Adaptation of superconducting fault current limiter to high-speed reclosing

NASA Astrophysics Data System (ADS)

Koyama, T.; Yanabu, S.

2009-10-01

Using a high temperature superconductor, we constructed and tested a model superconducting fault current limiter (SFCL). The superconductor might break in some cases because of its excessive generation of heat. Therefore, it is desirable to interrupt early the current that flows to superconductor. So, we proposed the SFCL using an electromagnetic repulsion switch which is composed of a superconductor, a vacuum interrupter and a by-pass coil, and its structure is simple. Duration that the current flow in the superconductor can be easily minimized to the level of less than 0.5 cycle using this equipment. On the other hand, the fault current is also easily limited by large reactance of the parallel coil. There is duty of high-speed reclosing after interrupting fault current in the electric power system. After the fault current is interrupted, the back-up breaker is re-closed within 350 ms. So, the electromagnetic repulsion switch should return to former state and the superconductor should be recovered to superconducting state before high-speed reclosing. Then, we proposed the SFCL using an electromagnetic repulsion switch which employs our new reclosing function. We also studied recovery time of the superconductor, because superconductor should be recovered to superconducting state within 350 ms. In this paper, the recovery time characteristics of the superconducting wire were investigated. Also, we combined the superconductor with the electromagnetic repulsion switch, and we did performance test. As a result, a high-speed reclosing within 350 ms was proven to be possible.

Critical Current Test of Liquid Hydrogen Cooled HTC Superconductors under External Magnetic Field

NASA Astrophysics Data System (ADS)

Shirai, Yasuyuki; Shiotsu, Masahiro; Tatsumoto, Hideki; Kobayashi, Hiroaki; Naruo, Yoshihiro; Nonaka, Satoshi; Inatani, Yoshifumi

High-Tc (HTC) superconductors including MgB2 will show excellent properties under temperature of Liquid Hydrogen (LH2:20K), which has large latent heat and low viscosity coefficient. In order to design and fabricate the LH2 cooled superconducting energy devices, we must clear the cooling property of LH2 for superconductors, the cooling system and safety design of LH2 cooled superconducting devices and electro-magnetic property evaluation of superconductors (BSCCO, REBCO and MgB2) and their magnets cooled by LH2. As the first step of the study, an experimental setup which can be used for investigating heat transfer characteristics of LH2 in a pool and also in forced flow (circulation loop with a pump), and also for evaluation of electro-magnetic properties of LH2 cooled superconductors under external magnetic field (up to 7 T). In this paper, we will show a short sketch of the experimental set-up, practical experiences in safety operation of liquid hydrogen cooling system and example test results of critical current evaluation of HTC superconductors cooled by LH2.

''Football'' test coil: a simulated service test of internally-cooled, cabled superconductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marston, P.G.; Iwasa, Y.; Thome, R.J.

Internally-cooled, cabled superconductor, (ICCS), appears from small-scale tests to be a viable alternative to pool-boiling cooled superconductors for large superconducting magnets. Potential advantages may include savings in helium inventory, smaller structure and ease of fabrication. Questions remain, however, about the structural performance of these systems. The ''football'' test coil has been designed to simulate the actual ''field-current-stress-thermal'' operating conditions of a 25 ka ICCS in a commercial scale MHD magnet. The test procedure will permit demonstration of the 20 year cyclic life of such a magnet in less than 20 days. This paper describes the design, construction and test ofmore » that coil which is wound of copper-stabilized niobium-titanium cable in steel conduit. 2 refs.« less

Nanoscale memory elements based on the superconductor-ferromagnet proximity effect and spin-transfer torque magnetization switching

NASA Astrophysics Data System (ADS)

Baek, Burm

Superconducting-ferromagnetic hybrid devices have potential for a practical memory technology compatible with superconducting logic circuits and may help realize energy-efficient, high-performance superconducting computers. We have developed Josephson junction devices with pseudo-spin-valve barriers. We observed changes in Josephson critical current depending on the magnetization state of the barrier (parallel or anti-parallel) through the superconductor-ferromagnet proximity effect. This effect persists to nanoscale devices in contrast to the remanent field effect. In nanopillar devices, the magnetization states of the pseudo-spin-valve barriers could also be switched with applied bias currents at 4 K, which is consistent with the spin-transfer torque effect in analogous room-temperature spin valve devices. These results demonstrate devices that combine major superconducting and spintronic effects for scalable read and write of memory states, respectively. Further challenges and proposals towards practical devices will also be discussed.In collaboration with: William Rippard, NIST - Boulder, Matthew Pufall, NIST - Boulder, Stephen Russek, NIST-Boulder, Michael Schneider, NIST - Boulder, Samuel Benz, NIST - Boulder, Horst Rogalla, NIST-Boulder, Paul Dresselhaus, NIST - Boulder

Study of Electromagnetic Repulsion Switch to High Speed Reclosing and Recover Time Characteristics of Superconductor

NASA Astrophysics Data System (ADS)

Koyama, Tomonori; Kaiho, Katsuyuki; Yamaguchi, Iwao; Yanabu, Satoru

Using a high-temperature superconductor, we constructed and tested a model superconducting fault current limiter (SFCL). The superconductor and vacuum interrupter as the commutation switch were connected in parallel using a bypass coil. When the fault current flows in this equipment, the superconductor is quenched and the current is then transferred to the parallel coil due to the voltage drop in the superconductor. This large current in the parallel coil actuates the magnetic repulsion mechanism of the vacuum interrupter and the current in the superconductor is broken. Using this equipment, the current flow time in the superconductor can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of the parallel coil. This system has many merits. So, we introduced to electromagnetic repulsion switch. There is duty of high speed re-closing after interrupting fault current in the electrical power system. So the SFCL should be recovered to superconducting state before high speed re-closing. But, superconductor generated heat at the time of quench. It takes time to recover superconducting state. Therefore it is a matter of recovery time. In this paper, we studied recovery time of superconductor. Also, we proposed electromagnetic repulsion switch with reclosing system.

Applications of Logic Coverage Criteria and Logic Mutation to Software Testing

ERIC Educational Resources Information Center

Kaminski, Garrett K.

2011-01-01

Logic is an important component of software. Thus, software logic testing has enjoyed significant research over a period of decades, with renewed interest in the last several years. One approach to detecting logic faults is to create and execute tests that satisfy logic coverage criteria. Another approach to detecting faults is to perform mutation…

Superconducting properties of copper oxide high-temperature superconductors

PubMed Central

Chen, Guanhua; Langlois, Jean-Marc; Guo, Yuejin; Goddard, William A.

1989-01-01

The equations for the magnon pairing theory of high-temperature copper-oxide-based superconductors are solved and used to calculate several properties, leading to results for specific heat and critical magnetic fields consistent with experimental results. In addition, the theory suggests an explanation of why there are two sets of transition temperatures (Tc ≈ 90 K and Tc ≈ 55 K) for the Y1Ba2Cu3O6+x class of superconductors. It also provides an explanation of why La2-xSrxCuO4 is a superconductor for only a small range of x (and suggests an experiment to independently test the theory). These results provide support for the magnon pairing theory of high-temperature superconductors. On the basis of the theory, some suggestions are made for improving these materials. PMID:16594038

Phase-tunable temperature amplifier

NASA Astrophysics Data System (ADS)

Paolucci, F.; Marchegiani, G.; Strambini, E.; Giazotto, F.

2017-06-01

Coherent caloritronics, the thermal counterpart of coherent electronics, has drawn growing attention since the discovery of heat interference in 2012. Thermal interferometers, diodes, transistors and nano-valves have been theoretically proposed and experimentally demonstrated by exploiting the quantum phase difference between two superconductors coupled through a Josephson junction. So far, the quantum-phase modulator has been realized in the form of a superconducting quantum interference device (SQUID) or a superconducting quantum interference proximity transistor (SQUIPT). Thence, an external magnetic field is necessary in order to manipulate the heat transport. Here, we theoretically propose the first on-chip fully thermal caloritronic device: the phase-tunable temperature amplifier (PTA). Taking advantage of a recently discovered thermoelectric effect in spin-split superconductors coupled to a spin-polarized system, we generate the magnetic flux controlling the transport through a temperature-biased SQUIPT by applying a temperature gradient. We simulate the behavior of the device and define a number of figures of merit in full analogy with voltage amplifiers. Notably, our architecture ensures almost infinite input thermal impedance, maximum gain of about 11 and efficiency reaching the 95%. This concept paves the way for applications in radiation sensing, thermal logics and quantum information.

Built-in-test by signature inspection (bitsi)

DOEpatents

Bergeson, Gary C.; Morneau, Richard A.

1991-01-01

A system and method for fault detection for electronic circuits. A stimulus generator sends a signal to the input of the circuit under test. Signature inspection logic compares the resultant signal from test nodes on the circuit to an expected signal. If the signals do not match, the signature inspection logic sends a signal to the control logic for indication of fault detection in the circuit. A data input multiplexer between the test nodes of the circuit under test and the signature inspection logic can provide for identification of the specific node at fault by the signature inspection logic. Control logic responsive to the signature inspection logic conveys information about fault detection for use in determining the condition of the circuit. When used in conjunction with a system test controller, the built-in test by signature inspection system and method can be used to poll a plurality of circuits automatically and continuous for faults and record the results of such polling in the system test controller.

Round Robin Test of Residual Resistance Ratio of Nb$$_3$$Sn Composite Superconductors

DOE PAGES

Matsushita, Teruo; Otabe, Edmund Soji; Kim, Dong Ho; ...

2017-12-07

A round robin test of residual resistance ratio (RRR) was performed for Nb 3Sn composite superconductors prepared by internal tin method by six institutes with the international standard test method described in IEC 61788-4. It was found that uncertainty mainly resulted from determination of the cryogenic resistance from the intersection of two straight lines drawn to fit the voltage vs. temperature curve around the resistive transition. As a result, the measurement clarified that RRR can be measured with expanded uncertainty not larger than 5% with the coverage factor 2 by using this test method.

Round Robin Test of Residual Resistance Ratio of Nb$$_3$$Sn Composite Superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matsushita, Teruo; Otabe, Edmund Soji; Kim, Dong Ho

A round robin test of residual resistance ratio (RRR) was performed for Nb 3Sn composite superconductors prepared by internal tin method by six institutes with the international standard test method described in IEC 61788-4. It was found that uncertainty mainly resulted from determination of the cryogenic resistance from the intersection of two straight lines drawn to fit the voltage vs. temperature curve around the resistive transition. As a result, the measurement clarified that RRR can be measured with expanded uncertainty not larger than 5% with the coverage factor 2 by using this test method.

Quantitative magneto-optical investigation of superconductor/ferromagnet hybrid structures

NASA Astrophysics Data System (ADS)

Shaw, G.; Brisbois, J.; Pinheiro, L. B. G. L.; Müller, J.; Blanco Alvarez, S.; Devillers, T.; Dempsey, N. M.; Scheerder, J. E.; Van de Vondel, J.; Melinte, S.; Vanderbemden, P.; Motta, M.; Ortiz, W. A.; Hasselbach, K.; Kramer, R. B. G.; Silhanek, A. V.

2018-02-01

We present a detailed quantitative magneto-optical imaging study of several superconductor/ferromagnet hybrid structures, including Nb deposited on top of thermomagnetically patterned NdFeB and permalloy/niobium with erasable and tailored magnetic landscapes imprinted in the permalloy layer. The magneto-optical imaging data are complemented with and compared to scanning Hall probe microscopy measurements. Comprehensive protocols have been developed for calibrating, testing, and converting Faraday rotation data to magnetic field maps. Applied to the acquired data, they reveal the comparatively weaker magnetic response of the superconductor from the background of larger fields and field gradients generated by the magnetic layer.

Integrated Cryogenic Electronics Testbed (ICE-T) for Evaluation of Superconductor and Cryo-Semiconductor Integrated Circuits

NASA Astrophysics Data System (ADS)

Dotsenko, V. V.; Sahu, A.; Chonigman, B.; Tang, J.; Lehmann, A. E.; Gupta, V.; Talalevskii, A.; Ruotolo, S.; Sarwana, S.; Webber, R. J.; Gupta, D.

2017-02-01

Research and development of cryogenic application-specific integrated circuits (ASICs), such as high-frequency (tens of GHz) semiconductor and superconductor mixed-signal circuits and large-scale (>10,000 Josephson Junctions) superconductor digital circuits, have long been hindered by the absence of specialized cryogenic test apparatus. During their iterative development phase, most ASICs require many additional input-output lines for applying independent bias controls, injecting test signals, and monitoring outputs of different sub-circuits. We are developing a full suite of modular test apparatus based on cryocoolers that do not consume liquid helium, and support extensive electrical interfaces to standard and custom test equipment. Our design separates the cryogenics from electrical connections, allowing even inexperienced users to conduct testing by simply mounting their ASIC on a removable electrical insert. Thermal connections between the cold stages and the inserts are made with robust thermal links. ICE-T accommodates two independent electrical inserts at the same time. We have designed various inserts, such as universal ones with all 40 or 80 coaxial cables and those with customized wiring and temperature-controlled stages. ICE-T features fast thermal cycling for rapid testing, enables detailed testing over long periods (days to months, if necessary), and even supports automated testing of digital ICs with modular additions.

21 CFR 866.5400 - Alpha-globulin immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5400 Alpha-globulin immuno-logical test system. (a) Identification. An alpha-globulin immunological... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Alpha-globulin immuno-logical test system. 866...

21 CFR 866.5380 - Free secretory component immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5380 Free secretory component immuno-logical test system. (a) Identification. A free... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Free secretory component immuno-logical test...

21 CFR 866.5350 - Fibrinopeptide A immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5350 Fibrinopeptide A immuno-logical test system. (a) Identification. A fibrinopeptide A immunological... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Fibrinopeptide A immuno-logical test system. 866...

People Like Logical Truth: Testing the Intuitive Detection of Logical Value in Basic Propositions.

PubMed

Nakamura, Hiroko; Kawaguchi, Jun

2016-01-01

Recent studies on logical reasoning have suggested that people are intuitively aware of the logical validity of syllogisms or that they intuitively detect conflict between heuristic responses and logical norms via slight changes in their feelings. According to logical intuition studies, logically valid or heuristic logic no-conflict reasoning is fluently processed and induces positive feelings without conscious awareness. One criticism states that such effects of logicality disappear when confounding factors such as the content of syllogisms are controlled. The present study used abstract propositions and tested whether people intuitively detect logical value. Experiment 1 presented four logical propositions (conjunctive, biconditional, conditional, and material implications) regarding a target case and asked the participants to rate the extent to which they liked the statement. Experiment 2 tested the effects of matching bias, as well as intuitive logic, on the reasoners' feelings by manipulating whether the antecedent or consequent (or both) of the conditional was affirmed or negated. The results showed that both logicality and matching bias affected the reasoners' feelings, and people preferred logically true targets over logically false ones for all forms of propositions. These results suggest that people intuitively detect what is true from what is false during abstract reasoning. Additionally, a Bayesian mixed model meta-analysis of conditionals indicated that people's intuitive interpretation of the conditional "if p then q" fits better with the conditional probability, q given p.

21 CFR 866.5270 - C-reactive protein immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5270 C-reactive protein immuno-logical test system. (a) Identification. A C-reactive protein... 21 Food and Drugs 8 2010-04-01 2010-04-01 false C-reactive protein immuno-logical test system. 866...

21 CFR 866.5360 - Cohn fraction IV immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5360 Cohn fraction IV immuno-logical test system. (a) Identification. A Cohn fraction IV immunological... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cohn fraction IV immuno-logical test system. 866...

21 CFR 866.5580 - Alpha-1-lipoprotein immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5580 Alpha-1-lipoprotein immuno-logical test system. (a) Identification. An alpha-1-lipoprotein... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Alpha-1-lipoprotein immuno-logical test system...

Accurate experimental and theoretical comparisons between superconductor-insulator-superconductor mixers showing weak and strong quantum effects

NASA Technical Reports Server (NTRS)

Mcgrath, W. R.; Richards, P. L.; Face, D. W.; Prober, D. E.; Lloyd, F. L.

1988-01-01

A systematic study of the gain and noise in superconductor-insulator-superconductor mixers employing Ta based, Nb based, and Pb-alloy based tunnel junctions was made. These junctions displayed both weak and strong quantum effects at a signal frequency of 33 GHz. The effects of energy gap sharpness and subgap current were investigated and are quantitatively related to mixer performance. Detailed comparisons are made of the mixing results with the predictions of a three-port model approximation to the Tucker theory. Mixer performance was measured with a novel test apparatus which is accurate enough to allow for the first quantitative tests of theoretical noise predictions. It is found that the three-port model of the Tucker theory underestimates the mixer noise temperature by a factor of about 2 for all of the mixers. In addition, predicted values of available mixer gain are in reasonable agreement with experiment when quantum effects are weak. However, as quantum effects become strong, the predicted available gain diverges to infinity, which is in sharp contrast to the experimental results. Predictions of coupled gain do not always show such divergences.

Development and evaluation of superconducting circuit elements

NASA Technical Reports Server (NTRS)

Haertling, Gene H.; Lee, Burtrand; Hsi, Dennis; Modi, Vibhakar; Marone, Matt

1990-01-01

An approach to the application of high Tc ceramic superconductors to practical circuit elements was developed and demonstrated. This method, known as the rigid-conductor process (RCP), involves the combination of a pre-formed, sintered, and tested superconductor material with an appropriate, rigid substrate via an epoxy adhesive which also serves to encapsulate the element from the ambient environment. Emphasis was on the practical means to achieve functional, reliable, and reproducible components. Although all of the work described in this report involved a YBa2Cu3Osub(7-x) high Tc superconductor material, the techniques developed and conclusions reached are equally applicable to other high Tc materials.

Spatial Relevancies of Hybrid Systems Relates to Superfluid

NASA Astrophysics Data System (ADS)

Hidajatullah-Widastra, Fatahillah

2015-05-01

After S/F hybrid system from Martin Lange, of spatial modulation Superconductor-Electromagnet hybrids superconductor producing studies conclusion, for superconductor at large Hand/or T(i.e close to the phase transitionline), when the superfluid densitiy tends to 0. Further as for He3-B superfluid ``testing ground'', after sought extensometer for every materials testing application from , in K Matsumoto:``Flux pinning Engineering for Application of HTS'', 2013 quote Higgs boson , whereas it plays role as similar phenomena of Meissner effect, both involves magnet levitating. Accompanying Gosowong vein, US 16. 3 Million costed study-report who said the toxic waste also endangering biodiversity[Dini Septanti: ``The BUYAT Case: Straddling between Environmental Securitization & De-securitization'', herewith proposed the ``complexity systems'' comparison comprises also phase transition & ``directed polymer'' notions of JP Bouchaud et al: ``Wealth condensation in a simple model of economy''. Incredibles acknowledgment to HE. Mr. Drs. P. SWANTORO & HE.Mr.Ir. H. ABURIZAL BAKRIE.

21 CFR 866.5330 - Factor XIII, A, S, immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866.5330 Factor XIII, A, S, immuno-logical test system. (a) Identification. A factor XIII, A, S... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Factor XIII, A, S, immuno-logical test system. 866...

People Like Logical Truth: Testing the Intuitive Detection of Logical Value in Basic Propositions

PubMed Central

2016-01-01

Recent studies on logical reasoning have suggested that people are intuitively aware of the logical validity of syllogisms or that they intuitively detect conflict between heuristic responses and logical norms via slight changes in their feelings. According to logical intuition studies, logically valid or heuristic logic no-conflict reasoning is fluently processed and induces positive feelings without conscious awareness. One criticism states that such effects of logicality disappear when confounding factors such as the content of syllogisms are controlled. The present study used abstract propositions and tested whether people intuitively detect logical value. Experiment 1 presented four logical propositions (conjunctive, biconditional, conditional, and material implications) regarding a target case and asked the participants to rate the extent to which they liked the statement. Experiment 2 tested the effects of matching bias, as well as intuitive logic, on the reasoners’ feelings by manipulating whether the antecedent or consequent (or both) of the conditional was affirmed or negated. The results showed that both logicality and matching bias affected the reasoners’ feelings, and people preferred logically true targets over logically false ones for all forms of propositions. These results suggest that people intuitively detect what is true from what is false during abstract reasoning. Additionally, a Bayesian mixed model meta-analysis of conditionals indicated that people’s intuitive interpretation of the conditional “if p then q” fits better with the conditional probability, q given p. PMID:28036402

Experimental feasibility study of the application of magnetic suspension techniques to large-scale aerodynamic test facilities

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1974-01-01

Based on the premises that (1) magnetic suspension techniques can play a useful role in large-scale aerodynamic testing and (2) superconductor technology offers the only practical hope for building large-scale magnetic suspensions, an all-superconductor three-component magnetic suspension and balance facility was built as a prototype and was tested successfully. Quantitative extrapolations of design and performance characteristics of this prototype system to larger systems compatible with existing and planned high Reynolds number facilities have been made and show that this experimental technique should be particularly attractive when used in conjunction with large cryogenic wind tunnels.

Development of a superconductor magnetic suspension and balance prototype facility for studying the feasibility of applying this technique to large scale aerodynamic testing

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1975-01-01

The basic research and development work towards proving the feasibility of operating an all-superconductor magnetic suspension and balance device for aerodynamic testing is presented. The feasibility of applying a quasi-six-degree-of freedom free support technique to dynamic stability research was studied along with the design concepts and parameters for applying magnetic suspension techniques to large-scale aerodynamic facilities. A prototype aerodynamic test facility was implemented. Relevant aspects of the development of the prototype facility are described in three sections: (1) design characteristics; (2) operational characteristics; and (3) scaling to larger facilities.

Experimental feasibility study of the application of magnetic suspension techniques to large-scale aerodynamic test facilities. [cryogenic traonics wind tunnel

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1975-01-01

Based on the premises that magnetic suspension techniques can play a useful role in large scale aerodynamic testing, and that superconductor technology offers the only practical hope for building large scale magnetic suspensions, an all-superconductor 3-component magnetic suspension and balance facility was built as a prototype and tested sucessfully. Quantitative extrapolations of design and performance characteristics of this prototype system to larger systems compatible with existing and planned high Reynolds number facilities at Langley Research Center were made and show that this experimental technique should be particularly attractive when used in conjunction with large cryogenic wind tunnels.

Potential aerospace applications of high temperature superconductors

NASA Technical Reports Server (NTRS)

Selim, Raouf

1994-01-01

The recent discovery of High Temperature Superconductors (HTS) with superconducting transition temperature, T(sub c), above the boiling point of liquid nitrogen has opened the door for using these materials in new and practical applications. These materials have zero resistance to electric current, have the capability of carrying large currents and as such have the potential to be used in high magnetic field applications. One of the space applications that can use superconductors is electromagnetic launch of payloads to low-earth-orbit. An electromagnetic gun-type launcher can be used in small payload systems that are launched at very high velocity, while sled-type magnetically levitated launcher can be used to launch larger payloads at smaller velocities. Both types of launchers are being studied by NASA and the aerospace industry. The use of superconductors will be essential in any of these types of launchers in order to produce the large magnetic fields required to obtain large thrust forces. Low Temperature Superconductor (LTS) technology is mature enough and can be easily integrated in such systems. As for the HTS, many leading companies are currently producing HTS coils and magnets that potentially can be mass-produced for these launchers. It seems that designing and building a small-scale electromagnetic launcher is the next logical step toward seriously considering this method for launching payloads into low-earth-orbit. A second potential application is the use of HTS to build sensitive portable devices for the use in Non Destructive Evaluation (NDE). Superconducting Quantum Interference Devices (SQUID's) are the most sensitive instruments for measuring changes in magnetic flux. By using HTS in SQUID's, one will be able to design a portable unit that uses liquid nitrogen or a cryocooler pump to explore the use of gradiometers or magnetometers to detect deep cracks or corrosion in structures. A third use is the replacement of Infra-Red (IR) sensor leads on Earth Orbit Systems (EOS) with HTS leads. IR detectors on these EOS missions are cooled to a 4.2K to improve their signal to noise ratio. They are connected to data acquisitions systems using manganin wires (low thermal conductors) to reduce the heat load on the cryogen. Replacing these wires with HTS leads will increase the lifetime of these missions by about 50 percent. This is a promising application that is ready for actual implementation on such systems. The analysis also show that an the number of IR detectors increase in larger EOS systems, substantial increase in the lifetime of each mission will be realized by using HTS leads instead of the manganin ones.

Test aspects of the JPL Viterbi decoder

NASA Technical Reports Server (NTRS)

Breuer, M. A.

1989-01-01

The generation of test vectors and design-for-test aspects of the Jet Propulsion Laboratory (JPL) Very Large Scale Integration (VLSI) Viterbi decoder chip is discussed. Each processor integrated circuit (IC) contains over 20,000 gates. To achieve a high degree of testability, a scan architecture is employed. The logic has been partitioned so that very few test vectors are required to test the entire chip. In addition, since several blocks of logic are replicated numerous times on this chip, test vectors need only be generated for each block, rather than for the entire circuit. These unique blocks of logic have been identified and test sets generated for them. The approach employed for testing was to use pseudo-exhaustive test vectors whenever feasible. That is, each cone of logid is tested exhaustively. Using this approach, no detailed logic design or fault model is required. All faults which modify the function of a block of combinational logic are detected, such as all irredundant single and multiple stuck-at faults.

Influence of kondo effect on the specific heat jump of anisotropic superconductors

NASA Astrophysics Data System (ADS)

Yoksan, S.

1986-01-01

A calculation for the specific heat jump of an anisotropic superconductor with Kondo impurities is presented. The impurities are treated within the Matsuura - Ichinose - Nagaoka framework and the anisotropy effect is described by the factorizable model of Markowitz and Kadanoff. We give explicit expressions for the change in specific heat jump due to anisotropy and impurities which can be tested experimentally.

21 CFR 866.5775 - Rheumatoid factor immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

.... Measurement of rheumatoid factor may aid in the diagnosis of rheumatoid arthritis. (b) Classification. Class... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Rheumatoid factor immuno-logical test system. 866....5775 Rheumatoid factor immuno-logical test system. (a) Identification. A rheumatoid factor...

21 CFR 866.5775 - Rheumatoid factor immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Measurement of rheumatoid factor may aid in the diagnosis of rheumatoid arthritis. (b) Classification. Class... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Rheumatoid factor immuno-logical test system. 866....5775 Rheumatoid factor immuno-logical test system. (a) Identification. A rheumatoid factor...

21 CFR 866.5775 - Rheumatoid factor immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

.... Measurement of rheumatoid factor may aid in the diagnosis of rheumatoid arthritis. (b) Classification. Class... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Rheumatoid factor immuno-logical test system. 866....5775 Rheumatoid factor immuno-logical test system. (a) Identification. A rheumatoid factor...

21 CFR 866.5580 - Alpha-1-lipoprotein immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Alpha-1-lipoprotein immuno-logical test system....5580 Alpha-1-lipoprotein immuno-logical test system. (a) Identification. An alpha-1-lipoprotein... the alpha-1-lipoprotein (high-density lipoprotein) in serum and plasma. Measurement of alpha-1...

21 CFR 866.5580 - Alpha-1-lipoprotein immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Alpha-1-lipoprotein immuno-logical test system....5580 Alpha-1-lipoprotein immuno-logical test system. (a) Identification. An alpha-1-lipoprotein... the alpha-1-lipoprotein (high-density lipoprotein) in serum and plasma. Measurement of alpha-1...

21 CFR 866.5580 - Alpha-1-lipoprotein immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Alpha-1-lipoprotein immuno-logical test system....5580 Alpha-1-lipoprotein immuno-logical test system. (a) Identification. An alpha-1-lipoprotein... the alpha-1-lipoprotein (high-density lipoprotein) in serum and plasma. Measurement of alpha-1...

21 CFR 866.5580 - Alpha-1-lipoprotein immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Alpha-1-lipoprotein immuno-logical test system....5580 Alpha-1-lipoprotein immuno-logical test system. (a) Identification. An alpha-1-lipoprotein... the alpha-1-lipoprotein (high-density lipoprotein) in serum and plasma. Measurement of alpha-1...

21 CFR 866.5775 - Rheumatoid factor immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Measurement of rheumatoid factor may aid in the diagnosis of rheumatoid arthritis. (b) Classification. Class... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Rheumatoid factor immuno-logical test system. 866....5775 Rheumatoid factor immuno-logical test system. (a) Identification. A rheumatoid factor...

21 CFR 866.5775 - Rheumatoid factor immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

.... Measurement of rheumatoid factor may aid in the diagnosis of rheumatoid arthritis. (b) Classification. Class... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Rheumatoid factor immuno-logical test system. 866....5775 Rheumatoid factor immuno-logical test system. (a) Identification. A rheumatoid factor...

Method for determining transport critical current densities and flux penetration depth in bulk superconductors

NASA Technical Reports Server (NTRS)

Israelsson, Ulf E. (Inventor); Strayer, Donald M. (Inventor)

1992-01-01

A contact-less method for determining transport critical current density and flux penetration depth in bulk superconductor material. A compressor having a hollow interior and a plunger for selectively reducing the free space area for distribution of the magnetic flux therein are formed of superconductor material. Analytical relationships, based upon the critical state model, Maxwell's equations and geometrical relationships define transport critical current density and flux penetration depth in terms of the initial trapped magnetic flux density and the ratio between initial and final magnetic flux densities whereby data may be reliably determined by means of the simple test apparatus for evaluating the current density and flux penetration depth.

Fine-Filament MgB2 Superconductor Wire

NASA Technical Reports Server (NTRS)

Cantu, Sherrie

2015-01-01

Hyper Tech Research, Inc., has developed fine-filament magnesium diboride (MgB2) superconductor wire for motors and generators used in turboelectric aircraft propulsion systems. In Phase I of the project, Hyper Tech demonstrated that MgB2 multifilament wires (<10 micrometers) could reduce alternating current (AC) losses that occur due to hysteresis, eddy currents, and coupling losses. The company refined a manufacturing method that incorporates a magnesium-infiltration process and provides a tenfold enhancement in critical current density over wire made by a conventional method involving magnesium-boron powder mixtures. Hyper Tech also improved its wire-drawing capability to fabricate fine multifilament strands. In Phase II, the company developed, manufactured, and tested the wire for superconductor and engineering current density and AC losses. Hyper Tech also fabricated MgB2 rotor coil packs for a superconducting generator. The ultimate goal is to enable low-cost, round, lightweight, low-AC-loss superconductors for motor and generator stator coils operating at 25 K in next-generation turboelectric aircraft propulsion systems.

Investigation of current transfer in built-up superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, J.R.; Dresner, L.; Lue, J.W.

1977-01-01

Superconductors carrying 10 kA or more have been widely suggested for use in fusion research and reactor magnets. Built-up or cable conductors have been proposed in which superconductor is concentrated in part of the conductor or part of the strands while the stabilizer occupies the rest. This scheme leads to substantial saving in manufacturing cost and to reduction of ac losses. Simplified analysis indicates that the current transfer from superconducting wire to normal wire takes place over a characteristic length depending on the resistivity of the contact barrier, the resistivity of the stabilizer, and the geometry of the conductor. Furthermore,more » the cold-end recovery suffers a reduction. Two types of conductors were constructed for the experimental test. Triplex conductors consisting of either three superconducting wires or two superconducting plus one copper wire were used to simulate cables. Laminated superconductor and copper strips with different soldering bonds were used for build-ups. Normal zone propagation and recovery experiments have been performed and results are compared with the theory.« less

Switchable geometric frustration in an artificial-spin-ice-superconductor heterosystem.

PubMed

Wang, Yong-Lei; Ma, Xiaoyu; Xu, Jing; Xiao, Zhi-Li; Snezhko, Alexey; Divan, Ralu; Ocola, Leonidas E; Pearson, John E; Janko, Boldizsar; Kwok, Wai-Kwong

2018-06-11

Geometric frustration emerges when local interaction energies in an ordered lattice structure cannot be simultaneously minimized, resulting in a large number of degenerate states. The numerous degenerate configurations may lead to practical applications in microelectronics 1 , such as data storage, memory and logic 2 . However, it is difficult to achieve very high degeneracy, especially in a two-dimensional system 3,4 . Here, we showcase in situ controllable geometric frustration with high degeneracy in a two-dimensional flux-quantum system. We create this in a superconducting thin film placed underneath a reconfigurable artificial-spin-ice structure 5 . The tunable magnetic charges in the artificial-spin-ice strongly interact with the flux quanta in the superconductor, enabling switching between frustrated and crystallized flux quanta states. The different states have measurable effects on the superconducting critical current profile, which can be reconfigured by precise selection of the spin-ice magnetic state through the application of an external magnetic field. We demonstrate the applicability of these effects by realizing a reprogrammable flux quanta diode. The tailoring of the energy landscape of interacting 'particles' using artificial-spin-ices provides a new paradigm for the design of geometric frustration, which could illuminate a path to control new functionalities in other material systems, such as magnetic skyrmions 6 , electrons and holes in two-dimensional materials 7,8 , and topological insulators 9 , as well as colloids in soft materials 10-13 .

CADAT network translator

NASA Technical Reports Server (NTRS)

Pitts, E. R.

1981-01-01

Program converts cell-net data into logic-gate models for use in test and simulation programs. Input consists of either Place, Route, and Fold (PRF) or Place-and-Route-in-Two-Dimensions (PR2D) layout data deck. Output consists of either Test Pattern Generator (TPG) or Logic-Simulation (LOGSIM) logic circuitry data deck. Designer needs to build only logic-gate-model circuit description since program acts as translator. Language is FORTRAN IV.

A Fifth Force: Generalized through Superconductors

NASA Technical Reports Server (NTRS)

Robertson, Glen A.

1999-01-01

The connection between the Biefield-Brown Effect, the recent repeat of the 1902 Trouton-Noble (TN) experiments, and the gravity shielding experiments was explored. This connection is visualized through high capacitive electron concentrations. From this connection, a theory is proposed that connects mass energy to gravity and a fifth force. The theory called the Gravi-Atomic Energy theory presents two new terms: Gravi-atomic energy and quantum vacuum pressure (QVP). Gravi-atomic energy is defined as the radiated mass energy, which acts on vacuum energy to create a QVP about a mass, resulting in gravity and the fifth force. The QVP emission from a superconductor was discussed followed by the description of a test for QVP from a superconductor using a Cavendish balance.

A Study of Geometric Understanding via Logical Reasoning in Hong Kong

ERIC Educational Resources Information Center

Poon, Kin-Keung; Leung, Chi-Keung

2016-01-01

The purposes of the study reported herein were to identify the common mistakes in geometry made by junior secondary school students in Hong Kong, and to compare the students' performance in geometry with their results in a logic test. A geometry test and a logic test were developed and administered to a sample of 554 students aged between 13 and…

Melting of the Abrikosov flux lattice in anisotropic superconductors

NASA Technical Reports Server (NTRS)

Beck, R. G.; Farrell, D. E.; Rice, J. P.; Ginsberg, D. M.; Kogan, V. G.

1992-01-01

It has been proposed that the Abrikosov flux lattice in high-Tc superconductors is melted over a significant fraction of the phase diagram. A thermodynamic argument is provided which establishes that the angular dependence of the melting temperature is controlled by the superconducting mass anisotropy. Using a low-frequency torsional-oscillator technique, this relationship has been tested in untwinned single-crystal YBa2Cu3O(7-delta). The results offer decisive support for the melting proposal.

LOGICAL REASONING ABILITY AND STUDENT PERFORMANCE IN GENERAL CHEMISTRY.

PubMed

Bird, Lillian

2010-03-01

Logical reasoning skills of students enrolled in General Chemistry at the University of Puerto Rico in Río Piedras were measured using the Group Assessment of Logical Thinking (GALT) test. The results were used to determine the students' cognitive level (concrete, transitional, formal) as well as their level of performance by logical reasoning mode (mass/volume conservation, proportional reasoning, correlational reasoning, experimental variable control, probabilistic reasoning and combinatorial reasoning). This information was used to identify particular deficiencies and gender effects, and to determine which logical reasoning modes were the best predictors of student performance in the general chemistry course. Statistical tests to analyze the relation between (a) operational level and final grade in both semesters of the course; (b) GALT test results and performance in the ACS General Chemistry Examination; and (c) operational level and student approach (algorithmic or conceptual) towards a test question that may be answered correctly using either strategy, were also performed.

LOGICAL REASONING ABILITY AND STUDENT PERFORMANCE IN GENERAL CHEMISTRY

PubMed Central

Bird, Lillian

2010-01-01

Logical reasoning skills of students enrolled in General Chemistry at the University of Puerto Rico in Río Piedras were measured using the Group Assessment of Logical Thinking (GALT) test. The results were used to determine the students’ cognitive level (concrete, transitional, formal) as well as their level of performance by logical reasoning mode (mass/volume conservation, proportional reasoning, correlational reasoning, experimental variable control, probabilistic reasoning and combinatorial reasoning). This information was used to identify particular deficiencies and gender effects, and to determine which logical reasoning modes were the best predictors of student performance in the general chemistry course. Statistical tests to analyze the relation between (a) operational level and final grade in both semesters of the course; (b) GALT test results and performance in the ACS General Chemistry Examination; and (c) operational level and student approach (algorithmic or conceptual) towards a test question that may be answered correctly using either strategy, were also performed. PMID:21373364

Processing of Bulk YBa2Cu3O(7-x) High Temperature Superconductor Materials for Gravity Modification Experiments and Performance Under AC Levitation

NASA Technical Reports Server (NTRS)

Koczor, Ronald; Noever, David; Hiser, Robert

1999-01-01

We have previously reported results using a high precision gravimeter to probe local gravity changes in the neighborhood of bulk-processed high temperature superconductor disks. Others have indicated that large annular disks (on the order of 25cm diameter) and AC levitation fields play an essential role in their observed experiments. We report experiments in processing such large bulk superconductors. Successful results depend on material mechanical characteristics, and pressure and heat treat protocols. Annular disks having rough dimensions of 30cm O.D., 7cm I.D. and 1 cm thickness have been routinely fabricated and tested under AC levitation fields ranging from 45 to 300OHz. Implications for space transportation initiatives and power storage flywheel technology will be discussed.

Simulated Laboratory in Digital Logic.

ERIC Educational Resources Information Center

Cleaver, Thomas G.

Design of computer circuits used to be a pencil and paper task followed by laboratory tests, but logic circuit design can now be done in half the time as the engineer accesses a program which simulates the behavior of real digital circuits, and does all the wiring and testing on his computer screen. A simulated laboratory in digital logic has been…

The High Field Path to Practical Fusion Energy

NASA Astrophysics Data System (ADS)

Mumgaard, Robert; Whyte, D.; Greenwald, M.; Hartwig, Z.; Brunner, D.; Sorbom, B.; Marmar, E.; Minervini, J.; Bonoli, P.; Irby, J.; Labombard, B.; Terry, J.; Vieira, R.; Wukitch, S.

2017-10-01

We propose a faster, lower cost development path for fusion energy enabled by high temperature superconductors, devices at high magnetic field, innovative technologies and modern approaches to technology development. Timeliness, scale, and economic-viability are the drivers for fusion energy to combat climate change and aid economic development. The opportunities provided by high-temperature superconductors, innovative engineering and physics, and new organizational structures identified over the last few years open new possibilities for realizing practical fusion energy that could meet mid-century de-carbonization needs. We discuss re-factoring the fusion energy development path with an emphasis on concrete risk retirement strategies utilizing a modular approach based on the high-field tokamak that leverages the broader tokamak physics understanding of confinement, stability, and operational limits. Elements of this plan include development of high-temperature superconductor magnets, simplified immersion blankets, advanced long-leg divertors, a compact divertor test tokamak, efficient current drive, modular construction, and demountable magnet joints. An R&D plan culminating in the construction of an integrated pilot plant and test facility modeled on the ARC concept is presented.

Defining, illustrating and reflecting on logic analysis with an example from a professional development program.

PubMed

Tremblay, Marie-Claude; Brousselle, Astrid; Richard, Lucie; Beaudet, Nicole

2013-10-01

Program designers and evaluators should make a point of testing the validity of a program's intervention theory before investing either in implementation or in any type of evaluation. In this context, logic analysis can be a particularly useful option, since it can be used to test the plausibility of a program's intervention theory using scientific knowledge. Professional development in public health is one field among several that would truly benefit from logic analysis, as it appears to be generally lacking in theorization and evaluation. This article presents the application of this analysis method to an innovative public health professional development program, the Health Promotion Laboratory. More specifically, this paper aims to (1) define the logic analysis approach and differentiate it from similar evaluative methods; (2) illustrate the application of this method by a concrete example (logic analysis of a professional development program); and (3) reflect on the requirements of each phase of logic analysis, as well as on the advantages and disadvantages of such an evaluation method. Using logic analysis to evaluate the Health Promotion Laboratory showed that, generally speaking, the program's intervention theory appeared to have been well designed. By testing and critically discussing logic analysis, this article also contributes to further improving and clarifying the method. Copyright © 2013 Elsevier Ltd. All rights reserved.

C-band superconductor/semiconductor hybrid field-effect transistor amplifier on a LaAlO3 substrate

NASA Technical Reports Server (NTRS)

Nahra, J. J.; Bhasin, K. B.; Toncich, S. S.; Subramanyam, G.; Kapoor, V. J.

1992-01-01

A single-stage C-band superconductor/semiconductor hybrid field-effect transistor amplifier was designed, fabricated, and tested at 77 K. The large area (1 inch x 0.5 inches) high temperature superconducting Tl-Ba-Ca-Cu-O (TBCCO) thin film was rf magnetron sputtered onto a LaAlO3 substrate. The film had a transition temperature of about 92 K after it was patterned and etched. The amplifier showed a gain of 6 dB and a 3 dB bandwidth of 100 MHz centered at 7.9 GHz. An identical gold amplifier circuit was tested at 77 K, and these results are compared with those from the hybrid amplifier.

Fabrication of high temperature superconductors

DOEpatents

Balachandran, Uthamalingam; Dorris, Stephen E.; Ma, Beihai; Li, Meiya

2003-06-17

A method of forming a biaxially aligned superconductor on a non-biaxially aligned substrate substantially chemically inert to the biaxially aligned superconductor comprising is disclosed. A non-biaxially aligned substrate chemically inert to the superconductor is provided and a biaxially aligned superconductor material is deposited directly on the non-biaxially aligned substrate. A method forming a plume of superconductor material and contacting the plume and the non-biaxially aligned substrate at an angle greater than 0.degree. and less than 90.degree. to deposit a biaxially aligned superconductor on the non-biaxially aligned substrate is also disclosed. Various superconductors and substrates are illustrated.

Effect of grain-alignment on the levitation force of melt-processed YBCO bulk superconductors

NASA Astrophysics Data System (ADS)

Yang, Wan-min; Zhou, Lian; Feng, Yong; Zhang, Ping-xiang; Wu, Min-zhi; Wu, Xiao-zu; Gawalek, W.

1999-07-01

Single-domain YBCO bulk superconductors have been fabricated by Top Seeded Melt Slow Cooling Growth(TSSCG) process. Two typical YBCO cylinder samples with differential grain-alignment were selected for the investigation of the relationship between the grain-alignment and the levitation force under the same testing condition at liquid nitrogen temperature. It is found that the levitation force values is much different for the two samples, the levitation force of the sample with H par c-axis is more than two times higher than that of the samples with H ⊥ c-axis. So it is necessary to take account of this anisotropy in practical applications. The relationship between a magnet and a superconductor can be well described with a double exponential function. All the results are discussed in details.

Clock Controller For Ac Self-Timing Analysis Of Logic System

DOEpatents

Lo, Tinchee; Flanagan, John D.

2004-05-18

A clock controller and clock generating method are provided for AC self-test timing analysis of a logic system. The controller includes latch circuitry which receives a DC input signal at a data input, and a pair of continuous out-of-phase clock signals at capture and launch clock inputs thereof. The latch circuitry outputs two overlapping pulses responsive to the DC input signal going high. The two overlapping pulses are provided to waveform shaper circuitry which produces therefrom two non-overlapping pulses at clock speed of the logic system to be tested. The two non-overlapping pulses are a single pair of clock pulses which facilitate AC self-test timing analysis of the logic system.

Energy and economic implications of magnetically-levitated vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, L.R.; Rote, D.M.

1988-01-01

Maglev systems, if implemented as ''spokes'' around the nation's major hub airports, have the potential to significantly reduce air traffic congestion. Maglev systems could improve the capacity of existing airports, obviating the need to build major new airports at a time when there is widespread public opposition to both airport expansion and new construction. Because of maglev's high speed (250-300 mph), the maglev has a logical market niche of trips between 100 and 600 miles. These short distance flights are the most energy intensive for the airlines; consequently, maglevs provide the opportunity to save 10 to 15% of the energymore » used by the scheduled airlines, through substitution of more efficient transport and reduced delays. Integrated into airline service, rather than competing with airlines, the economics of maglev systems is substantially enhanced. Indeed, a substantial portion of a national maglev system (3000 miles) around several major hub airports could be built over the next twenty years with a portion of the costs that the Federal Aviation Administration calculates are incurred by the airlines and the passengers---nearly $5 billion in 1986. Further, maglevs are the most promising large-scale application for the new class of high temperature superconductors, because of the relatively low threshold design requirements of the magnets compared to other potential applications. In addition, the new superconductors will improve maglev system reliability and may reduce capital and operating costs by as much as 10%. 2 figs.« less

Superconductor bearings, flywheels and transportation

NASA Astrophysics Data System (ADS)

Werfel, F. N.; Floegel-Delor, U.; Rothfeld, R.; Riedel, T.; Goebel, B.; Wippich, D.; Schirrmeister, P.

2012-01-01

This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS-FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN2. More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

Superconductor shields test chamber from ambient magnetic fields

NASA Technical Reports Server (NTRS)

Hildebrandt, A. F.

1965-01-01

Shielding a test chamber for magnetic components enables it to maintain a constant, low magnetic field. The chamber is shielded from ambient magnetic fields by a lead foil cylinder maintained in a superconducting state by liquid helium.

Continuous lengths of oxide superconductors

DOEpatents

Kroeger, Donald M.; List, III, Frederick A.

2000-01-01

A layered oxide superconductor prepared by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon. A continuous length of a second substrate ribbon is overlaid on the first substrate ribbon. Sufficient pressure is applied to form a bound layered superconductor precursor powder between the first substrate ribbon and the second substrate ribbon. The layered superconductor precursor is then heat treated to establish the oxide superconducting phase. The layered oxide superconductor has a smooth interface between the substrate and the oxide superconductor.

Teaching to the Test: A Pragmatic Approach to Teaching Logic

ERIC Educational Resources Information Center

Vannatta, Seth C.

2014-01-01

The proper goal of an introductory logic course, teaching critical thinking, is best achieved by maintaining the principle of continuity between student experiences and the curriculum. To demonstrate this I explain Dewey's naturalistic approach to logic and the process of inquiry, one which presents the elements of traditional logic in the…

The relationship between students critical thinking measured by science virtual test and students logical thinking on eighth grade secondary school

NASA Astrophysics Data System (ADS)

Nurismawati, R.; Sanjaya, Y.; Rusyati, L.

2018-05-01

The aim of this study is to examine the relationship between students’ critical thinking skill and students’ logical thinking skill of Junior High School students in Tasikmalaya city. The respondent consists of 168 students from eighth grade at three public schools in Tasikmalaya City. Science Virtual Test and Test of Logical Thinking were used in this research study. Science virtual test instrument consist of 26 questions with 5 different topics. IBM SPSS 23.00 program was used for analysis of the data. By the findings; students’ critical thinking skill has significant differences in elements of generating purpose, embodying point of view, utilizing concept and making implication and consequence. By Post Hoc LSD Test, from those four elements, there are significant differences between concrete - transitional groups and transitional – concrete groups. There is positive and weak correlation between students’ critical thinking and students’ logical thinking attainment.

Ground state, collective mode, phase soliton and vortex in multiband superconductors.

PubMed

Lin, Shi-Zeng

2014-12-10

This article reviews theoretical and experimental work on the novel physics in multiband superconductors. Multiband superconductors are characterized by multiple superconducting energy gaps in different bands with interaction between Cooper pairs in these bands. The discovery of prominent multiband superconductors MgB2 and later iron-based superconductors, has triggered enormous interest in multiband superconductors. The most recently discovered superconductors exhibit multiband features. The multiband superconductors possess novel properties that are not shared with their single-band counterpart. Examples include: the time-reversal symmetry broken state in multiband superconductors with frustrated interband couplings; the collective oscillation of number of Cooper pairs between different bands, known as the Leggett mode; and the phase soliton and fractional vortex, which are the main focus of this review. This review presents a survey of a wide range of theoretical exploratory and experimental investigations of novel physics in multiband superconductors. A vast amount of information derived from these studies is shown to highlight unusual and unique properties of multiband superconductors and to reveal the challenges and opportunities in the research on the multiband superconductivity.

Simultaneous constraint and phase conversion processing of oxide superconductors

DOEpatents

Li, Qi; Thompson, Elliott D.; Riley, Jr., Gilbert N.; Hellstrom, Eric E.; Larbalestier, David C.; DeMoranville, Kenneth L.; Parrell, Jeffrey A.; Reeves, Jodi L.

2003-04-29

A method of making an oxide superconductor article includes subjecting an oxide superconductor precursor to a texturing operation to orient grains of the oxide superconductor precursor to obtain a highly textured precursor; and converting the textured oxide superconducting precursor into an oxide superconductor, while simultaneously applying a force to the precursor which at least matches the expansion force experienced by the precursor during phase conversion to the oxide superconductor. The density and the degree of texture of the oxide superconductor precursor are retained during phase conversion. The constraining force may be applied isostatically.

Interactions and scattering of quantum vortices in a polariton fluid.

PubMed

Dominici, Lorenzo; Carretero-González, Ricardo; Gianfrate, Antonio; Cuevas-Maraver, Jesús; Rodrigues, Augusto S; Frantzeskakis, Dimitri J; Lerario, Giovanni; Ballarini, Dario; De Giorgi, Milena; Gigli, Giuseppe; Kevrekidis, Panayotis G; Sanvitto, Daniele

2018-04-13

Quantum vortices, the quantized version of classical vortices, play a prominent role in superfluid and superconductor phase transitions. However, their exploration at a particle level in open quantum systems has gained considerable attention only recently. Here we study vortex pair interactions in a resonant polariton fluid created in a solid-state microcavity. By tracking the vortices on picosecond time scales, we reveal the role of nonlinearity, as well as of density and phase gradients, in driving their rotational dynamics. Such effects are also responsible for the split of composite spin-vortex molecules into elementary half-vortices, when seeding opposite vorticity between the two spinorial components. Remarkably, we also observe that vortices placed in close proximity experience a pull-push scenario leading to unusual scattering-like events that can be described by a tunable effective potential. Understanding vortex interactions can be useful in quantum hydrodynamics and in the development of vortex-based lattices, gyroscopes, and logic devices.

Phase-coherent engineering of electronic heat currents with a Josephson modulator

NASA Astrophysics Data System (ADS)

Fornieri, Antonio; Blanc, Christophe; Bosisio, Riccardo; D'Ambrosio, Sophie; Giazotto, Francesco

In this contribution we report the realization of the first balanced Josephson heat modulator designed to offer full control at the nanoscale over the phase-coherent component of electronic thermal currents. The ability to master the amount of heat transferred through two tunnel-coupled superconductors by tuning their phase difference is the core of coherent caloritronics, and is expected to be a key tool in a number of nanoscience fields, including solid state cooling, thermal isolation, radiation detection, quantum information and thermal logic. Our device provides magnetic-flux-dependent temperature modulations up to 40 mK in amplitude with a maximum of the flux-to-temperature transfer coefficient reaching 200 mK per flux quantum at a bath temperature of 25 mK. Foremost, it demonstrates the exact correspondence in the phase-engineering of charge and heat currents, breaking ground for advanced caloritronic nanodevices such as thermal splitters, heat pumps and time-dependent electronic engines.

Defect-sensitivity analysis of an SEU immune CMOS logic family

NASA Technical Reports Server (NTRS)

Ingermann, Erik H.; Frenzel, James F.

1992-01-01

Fault testing of resistive manufacturing defects is done on a recently developed single event upset immune logic family. Resistive ranges and delay times are compared with those of traditional CMOS logic. Reaction of the logic to these defects is observed for a NOR gate, and an evaluation of its ability to cope with them is determined.

Majorana-assisted nonlocal electron transport through a floating topological superconductor

NASA Astrophysics Data System (ADS)

Ulrich, Jascha; Hassler, Fabian

2015-08-01

The nonlocal nature of the fermionic mode spanned by a pair of Majorana bound states in a one-dimensional topological superconductor has inspired many proposals aiming at demonstrating this property in transport. In particular, transport through the mode from a lead attached to the left bound state to a lead attached to the right will result in current cross correlations. For ideal zero modes on a grounded superconductor, the cross correlations are however completely suppressed in favor of purely local Andreev reflection. In order to obtain a nonvanishing cross correlation, previous studies have required the presence of an additional global charging energy. Adding nonlocal terms in the form of a global charging energy to the Hamiltonian when testing the intrinsic nonlocality of the Majorana modes seems to be conceptually troublesome. Here, we show that a floating superconductor allows observing nonlocal current correlations in the absence of charging energy. We show that the noninteracting and the Coulomb-blockade regime have the same peak conductance e2/h but different shot-noise power; whereas the shot noise is sub-Poissonian in the Coulomb-blockade regime in the large-bias limit, Poissonian shot noise is generically obtained in the noninteracting case.

Method of texturing a superconductive oxide precursor

DOEpatents

DeMoranville, Kenneth L.; Li, Qi; Antaya, Peter D.; Christopherson, Craig J.; Riley, Jr., Gilbert N.; Seuntjens, Jeffrey M.

1999-01-01

A method of forming a textured superconductor wire includes constraining an elongated superconductor precursor between two constraining elongated members placed in contact therewith on opposite sides of the superconductor precursor, and passing the superconductor precursor with the two constraining members through flat rolls to form the textured superconductor wire. The method includes selecting desired cross-sectional shape and size constraining members to control the width of the formed superconductor wire. A textured superconductor wire formed by the method of the invention has regular-shaped, curved sides and is free of flashing. A rolling assembly for single-pass rolling of the elongated precursor superconductor includes two rolls, two constraining members, and a fixture for feeding the precursor superconductor and the constraining members between the rolls. In alternate embodiments of the invention, the rolls can have machined regions which will contact only the elongated constraining members and affect the lateral deformation and movement of those members during the rolling process.

Ultrasonic and elastic properties of Tl- and Hg-Based cuprate superconductors: a review

NASA Astrophysics Data System (ADS)

Abd-Shukor, R.

2018-01-01

This review is regarding the ultrasonic and elastic properties of Tl- and Hg-based cuprate superconductors. The objectives of this paper were to review the ultrasonic attenuation above the transition temperature ?, and sound velocity and elastic anomalies at ? in the Tl- and Hg-based cuprate superconductors. A discontinuity in the sound velocity and elastic moduli is observed near ? for the Hg-based and other cuprate high temperature superconductor but not the Tl-based superconductor. Ultrasonic attenuation peaks are observed between 200 and 250 K in almost all Tl- and Hg-based cuprate superconductors reported. These peaks were attributed to lattice stepping and oxygen ordering in the Tl-O and Hg-O layers. Some Tl- and Hg-based superconductors show attenuation peak near ?. However, this is not a common feature for the cuprate superconductors. The ultrasonic attenuation decrease rate below ? is slower than that expected from a Bardeen-Cooper-Schrieffer (BCS) and pseudo-gapped superconductor.

Integrated circuit test-port architecture and method and apparatus of test-port generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teifel, John

A method and apparatus are provided for generating RTL code for a test-port interface of an integrated circuit. In an embodiment, a test-port table is provided as input data. A computer automatically parses the test-port table into data structures and analyzes it to determine input, output, local, and output-enable port names. The computer generates address-detect and test-enable logic constructed from combinational functions. The computer generates one-hot multiplexer logic for at least some of the output ports. The one-hot multiplexer logic for each port is generated so as to enable the port to toggle between data signals and test signals. Themore » computer then completes the generation of the RTL code.« less

Method of manufacturing a high temperature superconductor with improved transport properties

DOEpatents

Balachandran, Uthamalingam; Siegel, Richard W.; Askew, Thomas R.

2001-01-01

A method of preparing a high temperature superconductor. A method of preparing a superconductor includes providing a powdered high temperature superconductor and a nanophase paramagnetic material. These components are combined to form a solid compacted mass with the paramagnetic material disposed on the grain boundaries of the polycrystaline high temperature superconductor.

A Double-Decker Levitation Experiment Using a Sandwich of Superconductors.

ERIC Educational Resources Information Center

Jacob, Anthony T.; And Others

1988-01-01

Shows that the mutual repulsion that enables a superconductor to levitate a magnet and a magnet to levitate a superconductor can be combined into a single demonstration. Uses an overhead projector, two pellets of "1-2-3" superconductor, Nd-Fe-B magnets, liquid nitrogen, and paraffin. Offers superconductor preparation, hazards, and disposal…

System and method for quench and over-current protection of superconductor

DOEpatents

Huang, Xianrui; Laskaris, Evangelos Trifon; Sivasubramaniam, Kiruba Haran; Bray, James William; Ryan, David Thomas; Fogarty, James Michael; Steinbach, Albert Eugene

2005-05-31

A system and method for protecting a superconductor. The system may comprise a current sensor operable to detect a current flowing through the superconductor. The system may comprise a coolant temperature sensor operable to detect the temperature of a cryogenic coolant used to cool the superconductor to a superconductive state. The control circuit is operable to estimate the superconductor temperature based on the current flow and the coolant temperature. The system may also be operable to compare the estimated superconductor temperature to at least one threshold temperature and to initiate a corrective action when the superconductor temperature exceeds the at least one threshold temperature.

21 CFR 866.5860 - Total spinal fluid immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... diagnosis of multiple sclerosis and other diseases of the nervous system. (b) Classification. Class I... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Total spinal fluid immuno-logical test system. 866... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866...

21 CFR 866.5860 - Total spinal fluid immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... diagnosis of multiple sclerosis and other diseases of the nervous system. (b) Classification. Class I... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Total spinal fluid immuno-logical test system. 866... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866...

21 CFR 866.5860 - Total spinal fluid immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... diagnosis of multiple sclerosis and other diseases of the nervous system. (b) Classification. Class I... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Total spinal fluid immuno-logical test system. 866... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866...

21 CFR 866.5860 - Total spinal fluid immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... diagnosis of multiple sclerosis and other diseases of the nervous system. (b) Classification. Class I... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Total spinal fluid immuno-logical test system. 866... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866...

21 CFR 866.5860 - Total spinal fluid immuno-logical test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... diagnosis of multiple sclerosis and other diseases of the nervous system. (b) Classification. Class I... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Total spinal fluid immuno-logical test system. 866... SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test Systems § 866...

Hypothesis Testing in the Real World

ERIC Educational Resources Information Center

Miller, Jeff

2017-01-01

Critics of null hypothesis significance testing suggest that (a) its basic logic is invalid and (b) it addresses a question that is of no interest. In contrast to (a), I argue that the underlying logic of hypothesis testing is actually extremely straightforward and compelling. To substantiate that, I present examples showing that hypothesis…

An Introduction to the properties of Superconductors

NASA Astrophysics Data System (ADS)

Letarte, Alec

2001-03-01

A brief introductory presentation of the various properties of superconductors. The discussion will be focussed mainly on the newer ceramic superconductors, but the classic metal ones will also be touched upon. Some of the properties to be considered are: Optical properties, transport properties, persistent currents, coherence length, flux magnetisation, and the ``anti-gravity effect" produced be superconductors Another subject to be looked at will be the recent technological uses and developments of superconductors. For example, they have developed thin superconductors which they are making into a superconducting cable.

Apparatus for fabricating continuous lengths of superconductor

DOEpatents

Kroeger, Donald M.; List, III, Frederick A.

2002-01-01

A process and apparatus for manufacturing a superconductor. The process is accomplished by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon, overlaying a continuous length of a second substrate ribbon on said first substrate ribbon, and applying sufficient pressure to form a bound layered superconductor comprising a layer of said superconducting precursor powder between said first substrate ribbon and said second substrates ribbon. The layered superconductor is then heat treated to establish the superconducting phase of said superconductor precursor powder.

Apparatus for fabricating continuous lengths of superconductor

DOEpatents

Kroeger, Donald M.; List, III, Frederick A.

2001-01-01

A process and apparatus for manufacturing a superconductor. The process is accomplished by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon, overlaying a continuous length of a second substrate ribbon on said first substrate ribbon, and applying sufficient pressure to form a bound layered superconductor comprising a layer of said superconducting precursor powder between said first substrate ribbon and said second substrates ribbon. The layered superconductor is then heat treated to establish the superconducting phase of said superconductor precursor powder.

Operating characteristics of superconducting fault current limiter using 24kV vacuum interrupter driven by electromagnetic repulsion switch

NASA Astrophysics Data System (ADS)

Endo, M.; Hori, T.; Koyama, K.; Yamaguchi, I.; Arai, K.; Kaiho, K.; Yanabu, S.

2008-02-01

Using a high temperature superconductor, we constructed and tested a model Superconducting Fault Current Limiter (SFCL). SFCL which has a vacuum interrupter with electromagnetic repulsion mechanism. We set out to construct high voltage class SFCL. We produced the electromagnetic repulsion switch equipped with a 24kV vacuum interrupter(VI). There are problems that opening speed becomes late. Because the larger vacuum interrupter the heavier weight of its contact. For this reason, the current which flows in a superconductor may be unable to be interrupted within a half cycles of current. In order to solve this problem, it is necessary to change the design of the coil connected in parallel and to strengthen the electromagnetic repulsion force at the time of opening the vacuum interrupter. Then, the design of the coil was changed, and in order to examine whether the problem is solvable, the current limiting test was conducted. We examined current limiting test using 4 series and 2 parallel-connected YBCO thin films. We used 12-centimeter-long YBCO thin film. The parallel resistance (0.1Ω) is connected with each YBCO thin film. As a result, we succeed in interrupting the current of superconductor within a half cycle of it. Furthermore, series and parallel-connected YBCO thin film could limit without failure.

Metriwave final report

NASA Technical Reports Server (NTRS)

Williams, Wyman

1991-01-01

The superconductor-insulator-superconductor (SIS) mixer is a device which is being used in the construction of very sensitive receivers in the millimeter and submillimeter wavelength regions. With its potential for conversion gain and quantum-limited performance, it is becoming a device of prime importance in radio astronomy as well as earth and planetary atmospheric research. Many of the parameters of the SIS mixer cannot be readily measured in the laboratory, however, since most commercially available test instruments use test signal powers large enough to saturate or destroy SIS junctions. Detailed here is the construction of a microwave network analyzer with extremely low test signal powers. The results of a development performed by Dynamics Technology, Inc., under a Phase 2 SBIR contract from NASA (NAS7-1025) are documented. The work resulted in a network analyzer to be delivered to workers at the Jet Propulsion Laboratory, which should be capable of SIS mixer characterization in support of their ongoing work in this area.

Comparative Logic Modeling for Policy Analysis: The Case of HIV Testing Policy Change at the Department of Veterans Affairs

PubMed Central

Langer, Erika M; Gifford, Allen L; Chan, Kee

2011-01-01

Objective Logic models have been used to evaluate policy programs, plan projects, and allocate resources. Logic Modeling for policy analysis has been used rarely in health services research but can be helpful in evaluating the content and rationale of health policies. Comparative Logic Modeling is used here on human immunodeficiency virus (HIV) policy statements from the Department of Veterans Affairs (VA) and Centers for Disease Control and Prevention (CDC). We created visual representations of proposed HIV screening policy components in order to evaluate their structural logic and research-based justifications. Data Sources and Study Design We performed content analysis of VA and CDC HIV testing policy documents in a retrospective case study. Data Collection Using comparative Logic Modeling, we examined the content and primary sources of policy statements by the VA and CDC. We then quantified evidence-based causal inferences within each statement. Principal Findings VA HIV testing policy structure largely replicated that of the CDC guidelines. Despite similar design choices, chosen research citations did not overlap. The agencies used evidence to emphasize different components of the policies. Conclusion Comparative Logic Modeling can be used by health services researchers and policy analysts more generally to evaluate structural differences in health policies and to analyze research-based rationales used by policy makers. PMID:21689094

Thermomagnetic phenomena in the mixed state of high temperature superconductors

NASA Technical Reports Server (NTRS)

Meilikhov, E. Z.

1995-01-01

Galvano- and thermomagnetic-phenomena in high temperature superconductors, based on kinetic coefficients, are discussed, along with a connection between the electric field and the heat flow in superconductor mixed state. The relationship that determines the transport coefficients of high temperature superconductors in the mixed state based on Seebeck and Nernst effects is developed. It is shown that this relationship is true for a whole transition region of the resistive mixed state of a superconductor. Peltier, Ettingshausen and Righi-Leduc effects associated with heat conductivity as related to high temperature superconductors are also addressed.

Intrinsic superspin Hall current

NASA Astrophysics Data System (ADS)

Linder, Jacob; Amundsen, Morten; Risinggârd, Vetle

2017-09-01

We discover an intrinsic superspin Hall current: an injected charge supercurrent in a Josephson junction containing heavy normal metals and a ferromagnet generates a transverse spin supercurrent. There is no accompanying dissipation of energy, in contrast to the conventional spin Hall effect. The physical origin of the effect is an antisymmetric spin density induced among transverse modes ky near the interface of the superconductor arising due to the coexistence of p -wave and conventional s -wave superconducting correlations with a belonging phase mismatch. Our predictions can be tested in hybrid structures including thin heavy metal layers combined with strong ferromagnets and ordinary s -wave superconductors.

Electronic evidence of an insulator-superconductor crossover in single-layer FeSe/SrTiO3 films.

PubMed

He, Junfeng; Liu, Xu; Zhang, Wenhao; Zhao, Lin; Liu, Defa; He, Shaolong; Mou, Daixiang; Li, Fangsen; Tang, Chenjia; Li, Zhi; Wang, Lili; Peng, Yingying; Liu, Yan; Chen, Chaoyu; Yu, Li; Liu, Guodong; Dong, Xiaoli; Zhang, Jun; Chen, Chuangtian; Xu, Zuyan; Chen, Xi; Ma, Xucun; Xue, Qikun; Zhou, X J

2014-12-30

In high-temperature cuprate superconductors, it is now generally agreed that superconductivity is realized by doping an antiferromagnetic Mott (charge transfer) insulator. The doping-induced insulator-to-superconductor transition has been widely observed in cuprates, which provides important information for understanding the superconductivity mechanism. In the iron-based superconductors, however, the parent compound is mostly antiferromagnetic bad metal, raising a debate on whether an appropriate starting point should go with an itinerant picture or a localized picture. No evidence of doping-induced insulator-superconductor transition (or crossover) has been reported in the iron-based compounds so far. Here, we report an electronic evidence of an insulator-superconductor crossover observed in the single-layer FeSe film grown on a SrTiO3 substrate. By taking angle-resolved photoemission measurements on the electronic structure and energy gap, we have identified a clear evolution of an insulator to a superconductor with increasing carrier concentration. In particular, the insulator-superconductor crossover in FeSe/SrTiO3 film exhibits similar behaviors to that observed in the cuprate superconductors. Our results suggest that the observed insulator-superconductor crossover may be associated with the two-dimensionality that enhances electron localization or correlation. The reduced dimensionality and the interfacial effect provide a new pathway in searching for new phenomena and novel superconductors with a high transition temperature.

Electronic evidence of an insulator–superconductor crossover in single-layer FeSe/SrTiO3 films

PubMed Central

He, Junfeng; Liu, Xu; Zhang, Wenhao; Zhao, Lin; Liu, Defa; He, Shaolong; Mou, Daixiang; Li, Fangsen; Tang, Chenjia; Li, Zhi; Wang, Lili; Peng, Yingying; Liu, Yan; Chen, Chaoyu; Yu, Li; Liu, Guodong; Dong, Xiaoli; Zhang, Jun; Chen, Chuangtian; Xu, Zuyan; Chen, Xi; Ma, Xucun; Xue, Qikun; Zhou, X. J.

2014-01-01

In high-temperature cuprate superconductors, it is now generally agreed that superconductivity is realized by doping an antiferromagnetic Mott (charge transfer) insulator. The doping-induced insulator-to-superconductor transition has been widely observed in cuprates, which provides important information for understanding the superconductivity mechanism. In the iron-based superconductors, however, the parent compound is mostly antiferromagnetic bad metal, raising a debate on whether an appropriate starting point should go with an itinerant picture or a localized picture. No evidence of doping-induced insulator–superconductor transition (or crossover) has been reported in the iron-based compounds so far. Here, we report an electronic evidence of an insulator–superconductor crossover observed in the single-layer FeSe film grown on a SrTiO3 substrate. By taking angle-resolved photoemission measurements on the electronic structure and energy gap, we have identified a clear evolution of an insulator to a superconductor with increasing carrier concentration. In particular, the insulator–superconductor crossover in FeSe/SrTiO3 film exhibits similar behaviors to that observed in the cuprate superconductors. Our results suggest that the observed insulator–superconductor crossover may be associated with the two-dimensionality that enhances electron localization or correlation. The reduced dimensionality and the interfacial effect provide a new pathway in searching for new phenomena and novel superconductors with a high transition temperature. PMID:25502774

Disorder-induced topological phase transitions in two-dimensional spin-orbit coupled superconductors

PubMed Central

Qin, Wei; Xiao, Di; Chang, Kai; Shen, Shun-Qing; Zhang, Zhenyu

2016-01-01

Normal superconductors with Rashba spin-orbit coupling have been explored as candidate systems of topological superconductors. Here we present a comparative theoretical study of the effects of different types of disorder on the topological phases of two-dimensional Rashba spin-orbit coupled superconductors. First, we show that a topologically trivial superconductor can be driven into a chiral topological superconductor upon diluted doping of isolated magnetic disorder, which close and reopen the quasiparticle gap of the paired electrons in a nontrivial manner. Secondly, the superconducting nature of a topological superconductor is found to be robust against Anderson disorder, but the topological nature is not, converting the system into a topologically trivial state even in the weak scattering limit. These topological phase transitions are distinctly characterized by variations in the topological invariant. We discuss the central findings in connection with existing experiments, and provide new schemes towards eventual realization of topological superconductors. PMID:27991541

Radio frequency-assisted fast superconducting switch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solovyov, Vyacheslav; Li, Qiang

A radio frequency-assisted fast superconducting switch is described. A superconductor is closely coupled to a radio frequency (RF) coil. To turn the switch "off," i.e., to induce a transition to the normal, resistive state in the superconductor, a voltage burst is applied to the RF coil. This voltage burst is sufficient to induce a current in the coupled superconductor. The combination of the induced current with any other direct current flowing through the superconductor is sufficient to exceed the critical current of the superconductor at the operating temperature, inducing a transition to the normal, resistive state. A by-pass MOSFET maymore » be configured in parallel with the superconductor to act as a current shunt, allowing the voltage across the superconductor to drop below a certain value, at which time the superconductor undergoes a transition to the superconducting state and the switch is reset.« less

Disorder-induced topological phase transitions in two-dimensional spin-orbit coupled superconductors

NASA Astrophysics Data System (ADS)

Qin, Wei; Xiao, Di; Chang, Kai; Shen, Shun-Qing; Zhang, Zhenyu

2016-12-01

Normal superconductors with Rashba spin-orbit coupling have been explored as candidate systems of topological superconductors. Here we present a comparative theoretical study of the effects of different types of disorder on the topological phases of two-dimensional Rashba spin-orbit coupled superconductors. First, we show that a topologically trivial superconductor can be driven into a chiral topological superconductor upon diluted doping of isolated magnetic disorder, which close and reopen the quasiparticle gap of the paired electrons in a nontrivial manner. Secondly, the superconducting nature of a topological superconductor is found to be robust against Anderson disorder, but the topological nature is not, converting the system into a topologically trivial state even in the weak scattering limit. These topological phase transitions are distinctly characterized by variations in the topological invariant. We discuss the central findings in connection with existing experiments, and provide new schemes towards eventual realization of topological superconductors.

Fourth international cryogenic materials conference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, R.P.; Clark, A.F.

1982-01-01

In a comprehensive and current collection of 911 papers on a vest range of materials research topics in the field of cryogenic technology, this 924-page volume presents the most recent work of an international spectrum of materials and cyrogenic engineers at industrial and academic laboratories and institutions. The papers are collected under the broad headings of structural alloys; nometallics and composites; flux pinning in superconductors; high field superconductors; A15 superconductors; multiply-connected superconductors; superconductor properties and measurements; strain effects in superconductors; superconductor performance; the fabrication of superconductors; and the fabrication of structural alloys and composits. Ample and adequate photographic, plot, schematic,more » and tabulation illustration are included; the volume is also cross-referenced and has an author, materials, and subject index. It is volume 28 in a series which annually updates the existing knowledge of all areas of low-temperature technology.« less

Correlated spin currents generated by resonant-crossed Andreev reflections in topological superconductors

PubMed Central

He, James J.; Wu, Jiansheng; Choy, Ting-Pong; Liu, Xiong-Jun; Tanaka, Y.; Law, K. T.

2014-01-01

Topological superconductors, which support Majorana fermion excitations, have been the subject of intense studies due to their novel transport properties and their potential applications in fault-tolerant quantum computations. Here we propose a new type of topological superconductors that can be used as a novel source of correlated spin currents. We show that inducing superconductivity on a AIII class topological insulator wire, which respects a chiral symmetry and supports protected fermionic end states, will result in a topological superconductor. This topological superconductor supports two topological phases with one or two Majorana fermion end states, respectively. In the phase with two Majorana fermions, the superconductor can split Cooper pairs efficiently into electrons in two spatially separated leads due to Majorana-induced resonant-crossed Andreev reflections. The resulting currents in the leads are correlated and spin-polarized. Importantly, the proposed topological superconductors can be realized using quantum anomalous Hall insulators in proximity to superconductors. PMID:24492649

Programmer's guide to the fuzzy logic ramp metering algorithm : software design, integration, testing, and evaluation

DOT National Transportation Integrated Search

2000-02-01

A Fuzzy Logic Ramp Metering Algorithm was implemented on 126 ramps in the greater Seattle area. This report documents the implementation of the Fuzzy Logic Ramp Metering Algorithm at the Northwest District of the Washington State Department of Transp...

75 FR 36066 - Sunshine Act Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-24

... hearing to receive presentations on the following topic: Voting System Pre-Election Logic and Accuracy... voting system pre- election logic and accuracy testing and post-election audit grants may send a request... mail): Grants: Logic/Accuracy/Audits. Please note that these comments will be made available to the...

Rotational symmetry breaking in the topological superconductor SrxBi2Se3 probed by upper-critical field experiments

NASA Astrophysics Data System (ADS)

Pan, Y.; Nikitin, A. M.; Araizi, G. K.; Huang, Y. K.; Matsushita, Y.; Naka, T.; de Visser, A.

2016-06-01

Recently it was demonstrated that Sr intercalation provides a new route to induce superconductivity in the topological insulator Bi2Se3. Topological superconductors are predicted to be unconventional with an odd-parity pairing symmetry. An adequate probe to test for unconventional superconductivity is the upper critical field, Bc2. For a standard BCS layered superconductor Bc2 shows an anisotropy when the magnetic field is applied parallel and perpendicular to the layers, but is isotropic when the field is rotated in the plane of the layers. Here we report measurements of the upper critical field of superconducting SrxBi2Se3 crystals (Tc = 3.0 K). Surprisingly, field-angle dependent magnetotransport measurements reveal a large anisotropy of Bc2 when the magnet field is rotated in the basal plane. The large two-fold anisotropy, while six-fold is anticipated, cannot be explained with the Ginzburg-Landau anisotropic effective mass model or flux flow induced by the Lorentz force. The rotational symmetry breaking of Bc2 indicates unconventional superconductivity with odd-parity spin-triplet Cooper pairs (Δ4-pairing) recently proposed for rhombohedral topological superconductors, or might have a structural nature, such as self-organized stripe ordering of Sr atoms.

Wide-band operation of quasi-optical distributed superconductor/insulator/superconductor mixers with epitaxial NbN/AlN/NbN junctions

NASA Astrophysics Data System (ADS)

Kohjiro, S.; Shitov, S. V.; Wang, Z.; Uzawa, Y.; Miki, S.; Kawakami, A.; Shoji, A.

2004-05-01

For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 µm and the other is an anti-phase feed of 30 µm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature TRX = 691 K at 0.91 THz and TRX = 844 K at 0.80 THz, while 17% and TRX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz.

Rotational symmetry breaking in the topological superconductor SrxBi2Se3 probed by upper-critical field experiments.

PubMed

Pan, Y; Nikitin, A M; Araizi, G K; Huang, Y K; Matsushita, Y; Naka, T; de Visser, A

2016-06-28

Recently it was demonstrated that Sr intercalation provides a new route to induce superconductivity in the topological insulator Bi2Se3. Topological superconductors are predicted to be unconventional with an odd-parity pairing symmetry. An adequate probe to test for unconventional superconductivity is the upper critical field, Bc2. For a standard BCS layered superconductor Bc2 shows an anisotropy when the magnetic field is applied parallel and perpendicular to the layers, but is isotropic when the field is rotated in the plane of the layers. Here we report measurements of the upper critical field of superconducting SrxBi2Se3 crystals (Tc = 3.0 K). Surprisingly, field-angle dependent magnetotransport measurements reveal a large anisotropy of Bc2 when the magnet field is rotated in the basal plane. The large two-fold anisotropy, while six-fold is anticipated, cannot be explained with the Ginzburg-Landau anisotropic effective mass model or flux flow induced by the Lorentz force. The rotational symmetry breaking of Bc2 indicates unconventional superconductivity with odd-parity spin-triplet Cooper pairs (Δ4-pairing) recently proposed for rhombohedral topological superconductors, or might have a structural nature, such as self-organized stripe ordering of Sr atoms.

Rotational symmetry breaking in the topological superconductor SrxBi2Se3 probed by upper-critical field experiments

PubMed Central

Pan, Y.; Nikitin, A. M.; Araizi, G. K.; Huang, Y. K.; Matsushita, Y.; Naka, T.; de Visser, A.

2016-01-01

Recently it was demonstrated that Sr intercalation provides a new route to induce superconductivity in the topological insulator Bi2Se3. Topological superconductors are predicted to be unconventional with an odd-parity pairing symmetry. An adequate probe to test for unconventional superconductivity is the upper critical field, Bc2. For a standard BCS layered superconductor Bc2 shows an anisotropy when the magnetic field is applied parallel and perpendicular to the layers, but is isotropic when the field is rotated in the plane of the layers. Here we report measurements of the upper critical field of superconducting SrxBi2Se3 crystals (Tc = 3.0 K). Surprisingly, field-angle dependent magnetotransport measurements reveal a large anisotropy of Bc2 when the magnet field is rotated in the basal plane. The large two-fold anisotropy, while six-fold is anticipated, cannot be explained with the Ginzburg-Landau anisotropic effective mass model or flux flow induced by the Lorentz force. The rotational symmetry breaking of Bc2 indicates unconventional superconductivity with odd-parity spin-triplet Cooper pairs (Δ4-pairing) recently proposed for rhombohedral topological superconductors, or might have a structural nature, such as self-organized stripe ordering of Sr atoms. PMID:27350295

An ABS control logic based on wheel force measurement

NASA Astrophysics Data System (ADS)

Capra, D.; Galvagno, E.; Ondrak, V.; van Leeuwen, B.; Vigliani, A.

2012-12-01

The paper presents an anti-lock braking system (ABS) control logic based on the measurement of the longitudinal forces at the hub bearings. The availability of force information allows to design a logic that does not rely on the estimation of the tyre-road friction coefficient, since it continuously tries to exploit the maximum longitudinal tyre force. The logic is designed by means of computer simulation and then tested on a specific hardware in the loop test bench: the experimental results confirm that measured wheel force can lead to a significant improvement of the ABS performances in terms of stopping distance also in the presence of road with variable friction coefficient.

SCDFT Study of High Tc Nitride Superconductors

NASA Astrophysics Data System (ADS)

Arita, R.

Based on the density functional theory for superconductors (SCDFT), we study the pairing mechanism of the layered nitride superconductors, β-LixMNCl (M=Zr, Hf). Recently, it has been shown that SCDFT reproduces experimental superconducting transition temperatures (Tc) of conventional superconductors very accurately. Here we use SCDFT as a "litmus paper" to determine whether the system is a conventional or unconventional superconductor. We show that Tc estimated by SCDFT is less than half of the experimental Tc and its doping dependence is opposite to that observed in the experiments. The present result suggests that β- LixMNCl is not a Migdal-Eliashberg type superconductor.

Surface texturing of superconductors by controlled oxygen pressure

DOEpatents

Chen, N.; Goretta, K.C.; Dorris, S.E.

1999-01-05

A method of manufacture of a textured layer of a high temperature superconductor on a substrate is disclosed. The method involves providing an untextured high temperature superconductor material having a characteristic ambient pressure peritectic melting point, heating the superconductor to a temperature below the peritectic temperature, establishing a reduced pO{sub 2} atmosphere below ambient pressure causing reduction of the peritectic melting point to a reduced temperature which causes melting from an exposed surface of the superconductor and raising pressure of the reduced pO{sub 2} atmosphere to cause solidification of the molten superconductor in a textured surface layer. 8 figs.

Surface texturing of superconductors by controlled oxygen pressure

DOEpatents

Chen, Nan; Goretta, Kenneth C.; Dorris, Stephen E.

1999-01-01

A method of manufacture of a textured layer of a high temperature superconductor on a substrate. The method involves providing an untextured high temperature superconductor material having a characteristic ambient pressure peritectic melting point, heating the superconductor to a temperature below the peritectic temperature, establishing a reduced pO.sub.2 atmosphere below ambient pressure causing reduction of the peritectic melting point to a reduced temperature which causes melting from an exposed surface of the superconductor and raising pressure of the reduced pO.sub.2 atmosphere to cause solidification of the molten superconductor in a textured surface layer.

Failure detection and identification for a reconfigurable flight control system

NASA Technical Reports Server (NTRS)

Dallery, Francois

1987-01-01

Failure detection and identification logic for a fault-tolerant longitudinal control system were investigated. Aircraft dynamics were based upon the cruise condition for a hypothetical transonic business jet transport configuration. The fault-tolerant control system consists of conventional control and estimation plus a new outer loop containing failure detection, identification, and reconfiguration (FDIR) logic. It is assumed that the additional logic has access to all measurements, as well as to the outputs of the control and estimation logic. The pilot may also command the FDIR logic to perform special tests.

PREFACE: Special section featuring selected papers from the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors Special section featuring selected papers from the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors

NASA Astrophysics Data System (ADS)

Granados, Xavier; Sánchez, Àlvar; López-López, Josep

2012-10-01

The development of superconducting applications and superconducting engineering requires the support of consistent tools which can provide models for obtaining a good understanding of the behaviour of the systems and predict novel features. These models aim to compute the behaviour of the superconducting systems, design superconducting devices and systems, and understand and test the behavior of the superconducting parts. 50 years ago, in 1962, Charles Bean provided the superconducting community with a model efficient enough to allow the computation of the response of a superconductor to external magnetic fields and currents flowing through in an understandable way: the so called critical-state model. Since then, in addition to the pioneering critical-state approach, other tools have been devised for designing operative superconducting systems, allowing integration of the superconducting design in nearly standard electromagnetic computer-aided design systems by modelling the superconducting parts with consideration of time-dependent processes. In April 2012, Barcelona hosted the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors (HTS), the third in a series of workshops started in Lausanne in 2010 and followed by Cambridge in 2011. The workshop reflected the state-of-the-art and the new initiatives of HTS modelling, considering mathematical, physical and technological aspects within a wide and interdisciplinary scope. Superconductor Science and Technology is now publishing a selection of papers from the workshop which have been selected for their high quality. The selection comprises seven papers covering mathematical, physical and technological topics which contribute to an improvement in the development of procedures, understanding of phenomena and development of applications. We hope that they provide a perspective on the relevance and growth that the modelling of HTS superconductors has achieved in the past 25 years.

48 CFR 252.242-7004 - Material Management and Accounting System.

Code of Federal Regulations, 2011 CFR

2011-10-01

... logic for costing of material transactions; and (2) Assess its MMAS and take reasonable action to comply...) necessary to evaluate system logic and to verify through transaction testing that the system is operating as... transfers of parts; (7) Maintain a consistent, equitable, and unbiased logic for costing of material...

Matrix Tests as a Means of the Students' Level of Logical Thinking Diagnosis

ERIC Educational Resources Information Center

Roman, Yavich; Gein, Alexander; Gerkerova, Alexandra

2017-01-01

Nowadays pedagogical testing technology has become the basic tool for diagnosis and assessment of the level of students' mastery of learning material. Primarily they allow testing the acquired knowledge and skills in their use as a technology of the definite types of problems solution. Thus, the level of logical reasoning development plays a…

The effectiveness of web-programming module based on scientific approach to train logical thinking ability for students in vocational high school

NASA Astrophysics Data System (ADS)

Nashiroh, Putri Khoirin; Kamdi, Waras; Elmunsyah, Hakkun

2017-09-01

Web programming is a basic subject in Computer and Informatics Engineering, a program study in a vocational high school. It requires logical thinking ability in its learning activities. The purposes of this research were (1) to develop a web programming module that implement scientific approach that can improve logical thinking ability for students in vocational high school; and (2) to test the effectiveness of web programming module based on scientific approach to train students' logical thinking ability. The results of this research was a web-programming module that apply scientific approach for learning activities to improve logical thinking ability of students in the vocational high school. The results of the effectiveness test of web-programming module give conclusion that it was very effective to train logical thinking ability and to improve learning result, this conclusion was supported by: (1) the average of posttest result of students exceeds the minimum criterion value, it was 79.91; (2) the average percentage of students' logical thinking score is 82,98; and (3) the average percentage of students' responses to the web programming module was 81.86%.

FPGA-based gating and logic for multichannel single photon counting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pooser, Raphael C; Earl, Dennis Duncan; Evans, Philip G

2012-01-01

We present results characterizing multichannel InGaAs single photon detectors utilizing gated passive quenching circuits (GPQC), self-differencing techniques, and field programmable gate array (FPGA)-based logic for both diode gating and coincidence counting. Utilizing FPGAs for the diode gating frontend and the logic counting backend has the advantage of low cost compared to custom built logic circuits and current off-the-shelf detector technology. Further, FPGA logic counters have been shown to work well in quantum key distribution (QKD) test beds. Our setup combines multiple independent detector channels in a reconfigurable manner via an FPGA backend and post processing in order to perform coincidencemore » measurements between any two or more detector channels simultaneously. Using this method, states from a multi-photon polarization entangled source are detected and characterized via coincidence counting on the FPGA. Photons detection events are also processed by the quantum information toolkit for application testing (QITKAT)« less

Preface

NASA Astrophysics Data System (ADS)

2003-09-01

MEM03: The Second International Workshop on Mechano-Electromagnetic Properties of Composite Superconductors (Kyoto, Japan, 3–5 March 2003) Superconductivity is on course to be widely applied in various advanced technologies including: (1) magnetically levitated vehicles (MAGLEV), international thermonuclear experimental reactors (ITER), electric generators, high energy accelerator and magnetic resonance imaging (MRI) using metallic composite superconductors; (2) cable, fault-current-limiters (FCL), transformers, flywheels and motors by using oxide composite superconductors; (3) high field NMR and other sophisticated devices by combining both metallic and oxide superconductors. In order to create a real market for these advanced technologies using superconductivity, it is absolutely essential to develop superconducting wires/tapes with better performance. The development of accompanying assessment technologies is therefore indispensable for their R&D. Some important properties are related to the mechanical properties of the conductors. It is well known that degraded superconducting and mechanical properties (during fabrication as well as under operation) can cause serious problems, because the critical current depends sensitively on bending and tensile stresses, electromagnetic force, and mechanical and thermal cycling. Therefore he assessment of mechanical properties and the effect of strain on transport properties is crucial for improving and developing high performance superconducting devices. It is now very timely to have a meeting in order to discuss common scientific problems systematically and comprehensively. The Second International Workshop on Mechano-Electromagnetic Properties of Composite Superconductors, MEM03, was held in Kyoto, Japan, 3–5 March 2003, mainly to discuss the fundamentals of the following topics. • Electromagnetic properties: change of critical current, RRR and ac loss due to external forces like bending, compressive and tensile stresses, electromagnetic force, and mechanical and thermal cycling. • Mechanical properties: tensile and compressive properties, fatigue characteristics and fracture behaviour. • Thermal properties: thermal conductivity, thermal dilatation and thermal strain. • Modelling: prediction of critical current and mechanical properties of composite superconductors through statistical analysis, finite element analysis, etc. • Test methods: international cooperative research work to establish test methods for assessing mechano-electromagnetic properties based on the activity of VAMAS/TWA-16. This discussion took place with respect to three types of composites: • MFC (multifilamentary composite): BSCCO, MgB2, Nb-Ti, Nb3Sn and Nb3Al. • CCC (coated conductor composite): YBCO and ReBCO. • BCC (bulk crystal composite): YBCO and ReBCO. More than 55 researchers attended the MEM03 workshop, coming from eight different countries. A total of 42 papers were presented. In this special issue of Superconductor Science and Technology selected papers have been included that are concerned with the comprehensive scientific research subjects mentioned above. The aim of this issue is to provide a snapshot of some of the current state-of-the-art research and to promote further research into the mechano-electromagnetic properties of composite superconductors. The workshop was organized under the activities of NEDO technology quest and VAMAS/TWA-16. We wish to thank the following for their contribution to the success of the workshop: NEDO Super-ACE project, AFOSR, AOARD and IEC/TC90-JNC. Guest Editors: Kozo Osamura Hitoshi Wada Arman Nyilas Damian Hampshire

Process for fabricating continuous lengths of superconductor

DOEpatents

Kroeger, Donald M.; List, III, Frederick A.

1998-01-01

A process for manufacturing a superconductor. The process is accomplished by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon, overlaying a continuous length of a second substrate ribbon on said first substrate ribbon, and applying sufficient pressure to form a bound layered superconductor precursor between said first substrate ribbon and said second substrates ribbon. The layered superconductor precursor is then heat treated to form a super conductor layer.

Trapped field internal dipole superconducting motor generator

DOEpatents

Hull, John R.

2001-01-01

A motor generator including a high temperature superconductor rotor and an internally disposed coil assembly. The motor generator superconductor rotor is constructed of a plurality of superconductor elements magnetized to produce a dipole field. The coil assembly can be either a conventional conductor or a high temperature superconductor. The superconductor rotor elements include a magnetization direction and c-axis for the crystals of the elements and which is oriented along the magnetization direction.

Rigid levitation, flux pinning, thermal depinning and fluctuation in high-Tc superconductors

NASA Technical Reports Server (NTRS)

Brandt, E. H.

1991-01-01

Here, the author shows that the strong velocity-independent frictional force on a levitating superconductor and on any type-II superconductor moving in a homogeneous magnetic field is caused by pinning and depinning of the magnetic flux lines in its interior. Levitation may thus be used to investigate the pinning properties of a superconductor, and friction in a superconductor bearing may be minimized by choosing appropriate materials and geometries.

Self field triggered superconducting fault current limiter

DOEpatents

Tekletsadik, Kasegn D [Rexford, NY

2008-02-19

A superconducting fault current limiter array with a plurality of superconductor elements arranged in a meanding array having an even number of supconductors parallel to each other and arranged in a plane that is parallel to an odd number of the plurality of superconductors, where the odd number of supconductors are parallel to each other and arranged in a plane that is parallel to the even number of the plurality of superconductors, when viewed from a top view. The even number of superconductors are coupled at the upper end to the upper end of the odd number of superconductors. A plurality of lower shunt coils each coupled to the lower end of each of the even number of superconductors and a plurality of upper shunt coils each coupled to the upper end of each of the odd number of superconductors so as to generate a generally orthoganal uniform magnetic field during quenching using only the magenetic field generated by the superconductors.

Topological surface states in nodal superconductors.

PubMed

Schnyder, Andreas P; Brydon, Philip M R

2015-06-24

Topological superconductors have become a subject of intense research due to their potential use for technical applications in device fabrication and quantum information. Besides fully gapped superconductors, unconventional superconductors with point or line nodes in their order parameter can also exhibit nontrivial topological characteristics. This article reviews recent progress in the theoretical understanding of nodal topological superconductors, with a focus on Weyl and noncentrosymmetric superconductors and their protected surface states. Using selected examples, we review the bulk topological properties of these systems, study different types of topological surface states, and examine their unusual properties. Furthermore, we survey some candidate materials for topological superconductivity and discuss different experimental signatures of topological surface states.

Summary of Proton Test on the Quick Logic QL3025 at Indiana University

NASA Technical Reports Server (NTRS)

Katz, Richard

1998-01-01

This issue of the Programmable Logic Application Notes is a compilation of topics: (1) Proton irradiation tests were performed on the Quick Logic QL3025 at the Indian University Cyclotron facility. The devices, tests, and results are discussed; (2) The functional failure of EEPROM's in heavy ion environment is presented; (3) the Act 1 architecture is summarized; (4) Antifuse hardness and hardness testing is updated; the single even upset (SEU) response of hardwired flip-flops is also presented; (4) Total dose results of the ACT 2 and ACT 3 circuits is presented in a chart; (5) Recent sub-micron devices testing of total dose is presented in a chart along with brief discussion; and (6) a reference to the WWW site for more articles of interest.

Engineered flux-pinning centers in BSCCO TBCCO and YBCO superconductors

DOEpatents

Goretta, Kenneth C.; Lanagan, Michael T.; Miller, Dean J.; Sengupta, Suvankar; Parker, John C.; Hu, Jieguang; Balachandran, Uthamalingam; Siegel, Richard W.; Shi, Donglu

1999-01-01

A method of preparing a high temperature superconductor. A method of preparing a superconductor includes providing a powdered high temperature superconductor and a nanophase material. These components are combined to form a solid compacted mass with the material disposed in the polycrystalline high temperature superconductor. This combined mixture is rapidly heated, forming a dispersion of nanophase size particles without a eutectic reaction. These nanophase particles can have a flat plate or columnar type morphology.

Processing of Superconductor-Normal-Superconductor Josephson Edge Junctions

NASA Technical Reports Server (NTRS)

Kleinsasser, A. W.; Barner, J. B.

1997-01-01

The electrical behavior of epitaxial superconductor-normal-superconductor (SNS) Josephson edge junctions is strongly affected by processing conditions. Ex-situ processes, utilizing photoresist and polyimide/photoresist mask layers, are employed for ion milling edges for junctions with Yttrium-Barium-Copper-Oxide (YBCO) electrodes and primarily Co-doped YBCO interlayers.

MLM Builder: An Integrated Suite for Development and Maintenance of Arden Syntax Medical Logic Modules

PubMed Central

Sailors, R. Matthew

1997-01-01

The Arden Syntax specification for sharable computerized medical knowledge bases has not been widely utilized in the medical informatics community because of a lack of tools for developing Arden Syntax knowledge bases (Medical Logic Modules). The MLM Builder is a Microsoft Windows-hosted CASE (Computer Aided Software Engineering) tool designed to aid in the development and maintenance of Arden Syntax Medical Logic Modules (MLMs). The MLM Builder consists of the MLM Writer (an MLM generation tool), OSCAR (an anagram of Object-oriented ARden Syntax Compiler), a test database, and the MLManager (an MLM management information system). Working together, these components form a self-contained, unified development environment for the creation, testing, and maintenance of Arden Syntax Medical Logic Modules.

Logical Reasoning Ability and Student Performance in General Chemistry

ERIC Educational Resources Information Center

Bird, Lillian

2010-01-01

Logical reasoning skills of students enrolled in a general chemistry course at the University of Puerto Rico in Rio Piedras were measured using the Group Assessment of Logical Thinking (GALT) test. The results were used to determine the students' cognitive level (concrete, transitional, formal) as well as their level of performance by logical…

Giant ultrafast Kerr effect in superconductors

NASA Astrophysics Data System (ADS)

Robson, Charles W.; Fraser, Kieran A.; Biancalana, Fabio

2017-06-01

We study the ultrafast Kerr effect and high-harmonic generation in superconductors by formulating a model for a time-varying electromagnetic pulse normally incident on a thin-film superconductor. It is found that superconductors exhibit exceptionally large χ(3 ) due to the progressive destruction of Cooper pairs, and display high-harmonic generation at low incident intensities, and the highest nonlinear susceptibility of all known materials in the THz regime. Our theory opens up avenues for accessible analytical and numerical studies of the ultrafast dynamics of superconductors.

Engineered flux-pinning centers in BSCCO TBCCO and YBCO superconductors

DOEpatents

Goretta, K.C.; Lanagan, M.T.; Miller, D.J.; Sengupta, S.; Parker, J.C.; Hu, J.; Balachandran, U.; Siegel, R.W.; Shi, D.

1999-07-27

A method of preparing a high temperature superconductor is disclosed. A method of preparing a superconductor includes providing a powdered high temperature superconductor and a nanophase material. These components are combined to form a solid compacted mass with the material disposed in the polycrystalline high temperature superconductor. This combined mixture is rapidly heated, forming a dispersion of nanophase size particles without a eutectic reaction. These nanophase particles can have a flat plate or columnar type morphology. 4 figs.

Sealed glass coating of high temperature ceramic superconductors

DOEpatents

Wu, W.; Chu, C.Y.; Goretta, K.C.; Routbort, J.L.

1995-05-02

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor is disclosed. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor. 8 figs.

Sealed glass coating of high temperature ceramic superconductors

DOEpatents

Wu, Weite; Chu, Cha Y.; Goretta, Kenneth C.; Routbort, Jules L.

1995-01-01

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor.

Microwave Properties of Superconductors Close to the Superconductor-Insulator Transition.

PubMed

Feigel'man, M V; Ioffe, L B

2018-01-19

Strongly disordered pseudogapped superconductors are expected to display arbitrarily high values of kinetic inductance close to the superconductor-insulator transition (SIT), which make them attractive for the implementation of large dissipationless inductance. We develop the theory of the collective modes in these superconductors and discuss associated dissipation at microwave frequencies. We obtain the collective mode spectra dependence on the disorder level and conclude that collective modes become a relevant source of dissipation and noise in the outer proximity of the SIT.

Microwave Properties of Superconductors Close to the Superconductor-Insulator Transition

NASA Astrophysics Data System (ADS)

Feigel'man, M. V.; Ioffe, L. B.

2018-01-01

Strongly disordered pseudogapped superconductors are expected to display arbitrarily high values of kinetic inductance close to the superconductor-insulator transition (SIT), which make them attractive for the implementation of large dissipationless inductance. We develop the theory of the collective modes in these superconductors and discuss associated dissipation at microwave frequencies. We obtain the collective mode spectra dependence on the disorder level and conclude that collective modes become a relevant source of dissipation and noise in the outer proximity of the SIT.

Creativity. Education Today Series.

ERIC Educational Resources Information Center

Cropley, A. J.

The relationship between creativity and intelligence is discussed; and the position that intellect is not synonymous with the ability to respond in the usual logical way to a standard test item is developed. This logical (convergent) way of thinking, measured by IQ tests, is contrasted with the creative (divergent) way of thinking, measured by…

POLE.VAULT: A Semantic Framework for Health Policy Evaluation and Logical Testing.

PubMed

Shaban-Nejad, Arash; Okhmatovskaia, Anya; Shin, Eun Kyong; Davis, Robert L; Buckeridge, David L

2017-01-01

The major goal of our study is to provide an automatic evaluation framework that aligns the results generated through semantic reasoning with the best available evidence regarding effective interventions to support the logical evaluation of public health policies. To this end, we have designed the POLicy EVAlUation & Logical Testing (POLE.VAULT) Framework to assist different stakeholders and decision-makers in making informed decisions about different health-related interventions, programs and ultimately policies, based on the contextual knowledge and the best available evidence at both individual and aggregate levels.

Student Levels of Cognitive Development: Establishing Links between Logical Thinking Skills and Success in Earth Science

NASA Astrophysics Data System (ADS)

Steer, D. N.; McConnell, D. A.; Owens, K.

2003-12-01

Students in inquiry-based, general education Earth Science courses were found to display a wide range of logical thinking skills that are known indicators of success in science courses. The Group Assessment of Logical Thinking instrument that tests six logical operations was administered on the first day of class and near the end of the course. Such tests can be used to assess a student's overall level of cognitive development (concrete, transitional or formal) and specific logical thinking strengths or weaknesses. Results from paired pre- and post-course logical thinking tests of 393 students indicated that 25% of the incoming students were concrete, 30% were transitional and 45% were formal thinkers. Concrete and transitional thinkers were far more likely to withdraw from or fail the course when compared to their formal thinking peers (35%, 25% and 10% respectively). Differences in scores between genders were significant with 210 females testing at 30% concrete, 35% transitional and 35% formal on the pretest compared to 183 males who tested 15% concrete, 25% transitional and 60% formal. Overall logical thinking scores of students increased significantly in every inquiry-based class with lecture-based classes showing overall lower increases. Post-test data indicated that there were fewer concrete thinkers (16% female, 7% male), little change in the number of transitional thinkers (30% female, 23% male) and more formal thinkers (54% female, 70% male) toward the end of the inquiry-based course. Scores on two of the logical operations, conservation and probability, were sufficient to separate those who received a high grade (A or B in course) from those were unsuccessful (D, F or withdrew). Students who score low in conservation operations (n=46) tend to rely on intuition rather than logic when trying to understand typical Earth System concepts such as plate tectonics, atmospheric processes and climate change. Students who score low in probability skills (n=46) have difficulty distinguishing the difference between unrelated, but possible, data and those data that confirm a supposition. Such skills are necessary to properly apply the scientific method. By the end of the course, unsuccessful concrete students improved conservation reasoning skills to the same levels of their higher performing concrete peers on the post-test but remained behind them in probability skills. Successful transitional thinkers (n=50) displayed better correlation-reasoning skills than their lower performing contemporaries (n=51). Correlation reasoning skills are necessary to understand some of the many causal relationships routinely developed in the Earth Sciences (e.g. those associated with plate tectonics and earthquakes or volcanoes; CO2 and global climate change).

Overdamped Nb/Al-AlO{sub x}/Nb Josephson junctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lacquaniti, V.; Cagliero, C.; Maggi, S.

2005-01-24

We report the fabrication and characterization of overdamped Nb/Al-AlO{sub x}/Nb superconductor-insulator-superconductor Josephson junction whose fabrication process derives from that of the well-known hysteretic junctions. These junctions are an intermediate state between the superconductor-normal metal-superconductor and the superconductor-insulator-superconductor Josephson junctions. Stable and reproducible nonhysteretic current-voltage characteristics are obtained with a proper choice of the fabrication parameters. We have measured critical current densities J{sub C} from 10{sup 3} up to 2x10{sup 4} A/cm{sup 2}, with characteristic voltages from 80 to nearly 450 {mu}V. The junctions are stable against time and repeated thermal cycling.

Axial force in a superconductor magnet journal bearing

NASA Astrophysics Data System (ADS)

Postrekhin, E.; Chong, Wang; Ki Bui, Ma; Chen, Quark; Chu, Wei-Kan

Using superconductors and magnets, a journal bearing could be made from a permanent magnet cylinder in a superconductor ring. We have assembled a prototype superconductor magnet journal bearing of this configuration, and investigated the behavior of the axial force that it can provide. We have put together a numerical model of the interaction between the permanent magnet and the superconductor that is capable of describing these experimental results semi-quantitatively. Combining direct experimental measurements and using the numerical models proposed, we have achieved a qualitative understanding of the behavior of the axial force and its relationship of to the dimensions of the magnet and material quality such as the homogeneity of the superconductor that constitute the bearing.

Electro-physical properties of superconducting ceramic thick film prepared by partial melting method.

PubMed

Lee, Sang Heon

2013-05-01

BiSrCaCuO superconductor thick films were prepared at several curing temperatures, and their electro-physical properties were determined to find an optimum fabrication conditions. Critical temperatures of the superconductors were decreased with increasing melting temperature, which was related to the amount of equilibrium phases of the superconducting materials with temperature. The critical temperature of BiSrCaCuO bulk and thick film superconductors were 107 K and 96 K, respectively. The variation of susceptibility of the superconductor thick film formed at 950 degrees C had multi-step-type curve for 70 G externally applied field, whereas, a superconductor thick film formed at 885 degrees C had a single step-type curve like a bulk BiSrCaCuO ceramic superconductor in the temperature-susceptibility curves. A partial melting at 865 degrees C is one of optimum conditions for making a superconductor thick film with a relatively homogeneous phase.

Magnetic exchange coupling through superconductors: A trilayer study

NASA Astrophysics Data System (ADS)

Sá de Melo, C. A.

2000-11-01

The possibility of magnetic exchange coupling between two ferromagnets (F) separated by a superconductor (S) spacer is analyzed using the functional integral method. For this coupling to occur three prima facie conditions need to be satisfied. First, an indirect exchange coupling between the ferromagnets must exist when the superconductor is in its normal state. Second, superconductivity must not be destroyed due to the proximity to ferromagnetic boundaries. Third, roughness of the F/S interfaces must be small. Under these conditions, when the superconductor is cooled to below its critical temperature, the magnetic coupling changes. The appearance of the superconducting gap introduces a new length scale (the coherence length of the superconductor) and modifies the temperature dependence of the indirect exchange coupling existent in the normal state. The magnetic coupling is oscillatory both above and below the the critical temperature of the superconductor, as well as strongly temperature-dependent. However, at low temperatures the indirect exchange coupling decay length is controlled by the coherence length of the superconductor, while at temperatures close to and above the critical temperature of the superconductor the magnetic coupling decay length is controlled by the thermal length.

Current Technology--Superconductors.

ERIC Educational Resources Information Center

Grace, Gary; Barnhard, Ralph

1988-01-01

Describes how to make a superconducting pellet for classroom use. Details two tests that can use the pellet to demonstrate superconductivity. Discusses some of the mechanics and chemistry of superconductivity. Lists materiads and equipment necessary for these activities. (CW)

Testing and operating a multiprocessor chip with processor redundancy

DOEpatents

Bellofatto, Ralph E; Douskey, Steven M; Haring, Rudolf A; McManus, Moyra K; Ohmacht, Martin; Schmunkamp, Dietmar; Sugavanam, Krishnan; Weatherford, Bryan J

2014-10-21

A system and method for improving the yield rate of a multiprocessor semiconductor chip that includes primary processor cores and one or more redundant processor cores. A first tester conducts a first test on one or more processor cores, and encodes results of the first test in an on-chip non-volatile memory. A second tester conducts a second test on the processor cores, and encodes results of the second test in an external non-volatile storage device. An override bit of a multiplexer is set if a processor core fails the second test. In response to the override bit, the multiplexer selects a physical-to-logical mapping of processor IDs according to one of: the encoded results in the memory device or the encoded results in the external storage device. On-chip logic configures the processor cores according to the selected physical-to-logical mapping.

Young Children Detect and Avoid Logically Inconsistent Sources: The Importance of Communicative Context and Executive Function

ERIC Educational Resources Information Center

Doebel, Sabine; Rowell, Shaina F.; Koenig, Melissa A.

2016-01-01

The reported research tested the hypothesis that young children detect logical inconsistency in communicative contexts that support the evaluation of speakers' epistemic reliability. In two experiments (N = 194), 3- to 5-year-olds were presented with two speakers who expressed logically consistent or inconsistent claims. Three-year-olds failed to…

Ambient-pressure organic superconductor

DOEpatents

Williams, Jack M.; Wang, Hsien-Hau; Beno, Mark A.

1986-01-01

A new class of organic superconductors having the formula (ET).sub.2 MX.sub.2 wherein ET represents bis(ethylenedithio)-tetrathiafulvalene, M is a metal such as Au, Ag, In, Tl, Rb, Pd and the like and X is a halide. The superconductor (ET).sub.2 AuI.sub.2 exhibits a transition temperature of 5 K which is high for organic superconductors.

Gravitoelectromagnetism and Dark Energy in Superconductors

NASA Astrophysics Data System (ADS)

de Matos, Clovis Jacinto

A gravitomagnetic analog of the London moment in superconductors could explain the anomalous Cooper pair mass excess reported by Janet Tate. Ultimately the gravitomagnetic London moment is attributed to the breaking of the principle of general covariance in superconductors. This naturally implies nonconservation of classical energy-momentum. A possible relation with the manifestation of dark energy in superconductors is questioned.

Rotating superconductor magnet for producing rotating lobed magnetic field lines

DOEpatents

Hilal, Sadek K.; Sampson, William B.; Leonard, Edward F.

1978-01-01

This invention provides a rotating superconductor magnet for producing a rotating lobed magnetic field, comprising a cryostat; a superconducting magnet in the cryostat having a collar for producing a lobed magnetic field having oppositely directed adjacent field lines; rotatable support means for selectively rotating the superconductor magnet; and means for energizing the superconductor magnet.

System and method for quench protection of a superconductor

DOEpatents

Huang, Xianrui; Sivasubramaniam, Kiruba Haran; Bray, James William; Ryan, David Thomas

2008-03-11

A system and method for protecting a superconductor from a quench condition. A quench protection system is provided to protect the superconductor from damage due to a quench condition. The quench protection system comprises a voltage detector operable to detect voltage across the superconductor. The system also comprises a frequency filter coupled to the voltage detector. The frequency filter is operable to couple voltage signals to a control circuit that are representative of a rise in superconductor voltage caused by a quench condition and to block voltage signals that are not. The system is operable to detect whether a quench condition exists in the superconductor based on the voltage signal received via the frequency filter and to initiate a protective action in response.

Phonon properties of iron-based superconductors

NASA Astrophysics Data System (ADS)

Gupta, Yuhit; Goyal, Megha; Sinha, M. M.

2018-05-01

Earlier, it was thought there is antagonist relationship between superconductivity and ferromagnetic materials, But, a discovery of iron-based superconductors have removed this misconception. It gives an idea to make a review on the superconductivity properties of different materials. The new iron-based superconductors' present symmetry breaking competing phases in the form of tetragonal to orthorhombic transition. It consists of mainly four families [1111], [111], [122], and [11] type. Superconductivity of iron-based superconductors mainly related with the phonons and there is an excellent relation between phonons and superconductivity. Phonons properties are helpful in predicting the superconducting properties of materials. Phonon properties of iron-based superconductors in various phases are summarized in this study. We are presenting the review of phonon properties of iron-based superconductors.

Thermodynamic properties of Dynes superconductors

NASA Astrophysics Data System (ADS)

Herman, František; Hlubina, Richard

2018-01-01

The tunneling density of states in dirty s -wave superconductors is often well described by the phenomenological Dynes formula. Recently we have shown that this formula can be derived, within the coherent potential approximation, for superconductors with simultaneously present pair-conserving and pair-breaking impurity scattering. Here we demonstrate that the theory of such so-called Dynes superconductors is thermodynamically consistent. We calculate the specific heat and critical field of the Dynes superconductors, and we show that their gap parameter, specific heat, critical field, and penetration depth exhibit power-law scaling with temperature in the low-temperature limit. We also show that in the vicinity of a coupling-constant-controlled superconductor to normal metal transition, the Homes law is replaced by a different, pair-breaking-dominated scaling law.

Development of Fuzzy Logic Controller for Quanser Bench-Top Helicopter

NASA Astrophysics Data System (ADS)

Jafri, M. H.; Mansor, H.; Gunawan, T. S.

2017-11-01

Bench-top helicopter is a laboratory scale helicopter that usually used as a testing bench of the real helicopter behavior. This helicopter is a 3 Degree of Freedom (DOF) helicopter which works by three different axes wshich are elevation, pitch and travel. Thus, fuzzy logic controller has been proposed to be implemented into Quanser bench-top helicopter because of its ability to work with non-linear system. The objective for this project is to design and apply fuzzy logic controller for Quanser bench-top helicopter. Other than that, fuzzy logic controller performance system has been simulated to analyze and verify its behavior over existing PID controller by using Matlab & Simulink software. In this research, fuzzy logic controller has been designed to control the elevation angle. After simulation has been performed, it can be seen that simulation result shows that fuzzy logic elevation control is working for 4°, 5° and 6°. These three angles produce zero steady state error and has a fast response. Other than that, performance comparisons have been performed between fuzzy logic controller and PID controller. Fuzzy logic elevation control has a better performance compared to PID controller where lower percentage overshoot and faster settling time have been achieved in 4°, 5° and 6° step response test. Both controller are have zero steady state error but fuzzy logic controller is managed to produce a better performance in term of settling time and percentage overshoot which make the proposed controller is reliable compared to the existing PID controller.

Tests on a 30 kVA class superconducting transformer

NASA Astrophysics Data System (ADS)

Yoneda, E. S.; Tashiro, I.; Morohoshi, M.; Ito, D.

To demonstrate the applicability of superconductors to electric power machines, the present authors made and tested a 30 kVA class single-phase superconducting transformer. The aim of the study was to determine the superconducting transformer properties. Therefore the superconducting transformer has a simple structure, i.e. the primary to secondary voltage ratio is 1:1 and the iron core is immersed in liquid helium. The core loss, evaluated from no-load tests, was 13 W and leakage impedance, obtained by short circuit tests, was 0.02 Ω in accordance with a calculated value. The superconducting transformer showed the limitation effect of fault currents. The authors succeeded in continuous operation with a 0.5 Ω load resistance. These results suggest that efficiency can be 98.5%, if the iron core is located outside the cryostat and if high Tc superconductors are used as current leads. Superconducting windings exhibit training quenches in general. The authors also developed a superconducting transformer quench detector with a third winding around the iron core. The quench detector revealed that the secondary winding quenches before the primary winding.

Diagnosable structured logic array

NASA Technical Reports Server (NTRS)

Whitaker, Sterling (Inventor); Miles, Lowell (Inventor); Gambles, Jody (Inventor); Maki, Gary K. (Inventor)

2009-01-01

A diagnosable structured logic array and associated process is provided. A base cell structure is provided comprising a logic unit comprising a plurality of input nodes, a plurality of selection nodes, and an output node, a plurality of switches coupled to the selection nodes, where the switches comprises a plurality of input lines, a selection line and an output line, a memory cell coupled to the output node, and a test address bus and a program control bus coupled to the plurality of input lines and the selection line of the plurality of switches. A state on each of the plurality of input nodes is verifiably loaded and read from the memory cell. A trusted memory block is provided. The associated process is provided for testing and verifying a plurality of truth table inputs of the logic unit.

Comparing Two Tests of Formal Reasoning in a College Chemistry Context

ERIC Educational Resources Information Center

Jiang, Bo; Xu, Xiaoying; Garcia, Alicia; Lewis, Jennifer E.

2010-01-01

The Test of Logical Thinking (TOLT) and the Group Assessment of Logical Thinking (GALT) are two of the instruments most widely used by science educators and researchers to measure students' formal reasoning abilities. Based on Piaget's cognitive development theory, formal thinking ability has been shown to be essential for student achievement in…

21 CFR 866.5400 - Alpha-globulin immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... alpha-globulin (a serum protein) in serum and other body fluids. Measurement of alpha-globulin may aid... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Alpha-globulin immuno-logical test system. 866.5400 Section 866.5400 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5350 - Fibrinopeptide A immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... fibrinopeptide A (a blood-clotting factor) in plasma and other body fluids. Measurement of fibrinopeptide A may... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Fibrinopeptide A immuno-logical test system. 866.5350 Section 866.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5350 - Fibrinopeptide A immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... fibrinopeptide A (a blood-clotting factor) in plasma and other body fluids. Measurement of fibrinopeptide A may... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Fibrinopeptide A immuno-logical test system. 866.5350 Section 866.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5350 - Fibrinopeptide A immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... fibrinopeptide A (a blood-clotting factor) in plasma and other body fluids. Measurement of fibrinopeptide A may... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Fibrinopeptide A immuno-logical test system. 866.5350 Section 866.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5400 - Alpha-globulin immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... alpha-globulin (a serum protein) in serum and other body fluids. Measurement of alpha-globulin may aid... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Alpha-globulin immuno-logical test system. 866.5400 Section 866.5400 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5350 - Fibrinopeptide A immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... fibrinopeptide A (a blood-clotting factor) in plasma and other body fluids. Measurement of fibrinopeptide A may... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Fibrinopeptide A immuno-logical test system. 866.5350 Section 866.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5400 - Alpha-globulin immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... alpha-globulin (a serum protein) in serum and other body fluids. Measurement of alpha-globulin may aid... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Alpha-globulin immuno-logical test system. 866.5400 Section 866.5400 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 866.5400 - Alpha-globulin immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... alpha-globulin (a serum protein) in serum and other body fluids. Measurement of alpha-globulin may aid... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Alpha-globulin immuno-logical test system. 866.5400 Section 866.5400 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

Determination of Factors Related to Students' Understandings of Heat, Temperature and Internal Energy Concepts

ERIC Educational Resources Information Center

Gurcay, Deniz; Gulbas, Etna

2018-01-01

The purpose of this research is to investigate the relationships between high school students' learning approaches and logical thinking abilities and their understandings of heat, temperature and internal energy concepts. Learning Approach Questionnaire, Test of Logical Thinking and Three-Tier Heat, Temperature and Internal Energy Test were used…

Electronic structure and superconductivity of FeSe-related superconductors.

PubMed

Liu, Xu; Zhao, Lin; He, Shaolong; He, Junfeng; Liu, Defa; Mou, Daixiang; Shen, Bing; Hu, Yong; Huang, Jianwei; Zhou, X J

2015-05-13

FeSe superconductors and their related systems have attracted much attention in the study of iron-based superconductors owing to their simple crystal structure and peculiar electronic and physical properties. The bulk FeSe superconductor has a superconducting transition temperature (Tc) of ~8 K and it can be dramatically enhanced to 37 K at high pressure. On the other hand, its cousin system, FeTe, possesses a unique antiferromagnetic ground state but is non-superconducting. Substitution of Se with Te in the FeSe superconductor results in an enhancement of Tc up to 14.5 K and superconductivity can persist over a large composition range in the Fe(Se,Te) system. Intercalation of the FeSe superconductor leads to the discovery of the AxFe2-ySe2 (A = K, Cs and Tl) system that exhibits a Tc higher than 30 K and a unique electronic structure of the superconducting phase. A recent report of possible high temperature superconductivity in single-layer FeSe/SrTiO3 films with a Tc above 65 K has generated much excitement in the community. This pioneering work opens a door for interface superconductivity to explore for high Tc superconductors. The distinct electronic structure and superconducting gap, layer-dependent behavior and insulator-superconductor transition of the FeSe/SrTiO3 films provide critical information in understanding the superconductivity mechanism of iron-based superconductors. In this paper, we present a brief review of the investigation of the electronic structure and superconductivity of the FeSe superconductor and related systems, with a particular focus on the FeSe films.

Development of superconductor magnetic suspension and balance prototype facility for studying the feasibility of applying this technique to large scale aerodynamic testing

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1975-01-01

The unique design and operational characteristics of a prototype magnetic suspension and balance facility which utilizes superconductor technology are described and discussed from the point of view of scalability to large sizes. The successful experimental demonstration of the feasibility of this new magnetic suspension concept of the University of Virginia, together with the success of the cryogenic wind-tunnel concept developed at Langley Research Center, appear to have finally opened the way to clean-tunnel, high-Re aerodynamic testing. Results of calculations corresponding to a two-step design extrapolation from the observed performance of the prototype magnetic suspension system to a system compatible with the projected cryogenic transonic research tunnel are presented to give an order-of-magnitude estimate of expected performance characteristics. Research areas where progress should lead to improved design and performance of large facilities are discussed.

Magnetic exchange coupling through superconductors : a trilayer study.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sa de Melo, C. A. R.; Materials Science Division

1997-09-08

The possibility of magnetic exchange coupling between two ferromagnets (F) separated by a superconductor (S) spacer is analyzed using the functional integral method. For this coupling to occur three prima facie conditions need to be satisfied. First, an indirect exchange coupling between the ferromagnets must exist when the superconductor is in its normal state. Second, superconductivity must not be destroyed due to the proximity to ferromagnetic boundaries. Third, roughness of the F/S interfaces must be small. Under these conditions, when the superconductor is cooled to below its critical temperature, the magnetic coupling changes. The appearance of the superconducting gap introducesmore » a new length scale (the coherence length of the superconductor) and modifies the temperature dependence of the indirect exchange coupling existent in the normal state. The magnetic coupling is oscillatory both above and below the critical temperature of the superconductor, as well as strongly temperature-dependent. However, at low temperatures the indirect exchange coupling decay length is controlled by the coherence length of the superconductor, while at temperatures close to and above the critical temperature of the superconductor the magnetic coupling decay length is controlled by the thermal length.« less

Superconductor Electronics Fabrication Process with MoNx Kinetic Inductors and Self-Shunted Josephson Junctions

NASA Astrophysics Data System (ADS)

Tolpygo, Sergey K.; Bolkhovsky, Vladimir; Oates, Daniel E.; Rastogi, Ravi; Zarr, Scott; Day, Alexandra L.; Weir, Tarence J.; Wynn, Alex; Johnson, Leonard M.

2018-06-01

Recent progress in superconductor electronics fabrication has enabled single-flux-quantum (SFQ) digital circuits with close to one million Josephson junctions (JJs) on 1-cm$^2$ chips. Increasing the integration scale further is challenging because of the large area of SFQ logic cells, mainly determined by the area of resistively shunted Nb/AlO$_x$-Al/Nb JJs and geometrical inductors utilizing multiple layers of Nb. To overcome these challenges, we are developing a fabrication process with self-shunted high-J$_c$ JJs and compact thin-film MoN$_x$ kinetic inductors instead of geometrical inductors. We present fabrication details and properties of MoN$_x$ films with a wide range of T$_c$, including residual stress, electrical resistivity, critical current, and magnetic field penetration depth {\\lambda}$_0$. As kinetic inductors, we implemented Mo$_2$N films with T$_c$ about 8 K, {\\lambda}$_0$ about 0.51 {\\mu}m, and inductance adjustable in the range from 2 to 8 pH/sq. We also present data on fabrication and electrical characterization of Nb-based self-shunted JJs with AlO$_x$ tunnel barriers and J$_c$ = 0.6 mA/{\\mu}m$^2$, and with 10-nm thick Si$_{1-x}$Nb$_x$ barriers, with x from 0.03 to 0.15, fabricated on 200-mm wafers by co-sputtering. We demonstrate that the electron transport mechanism in Si$_{1-x}$Nb$_x$ barriers at x < 0.08 is inelastic resonant tunneling via chains of multiple localized states. At larger x, their Josephson characteristics are strongly dependent on x and residual stress in Nb electrodes, and in general are inferior to AlO$_x$ tunnel barriers.

Superconducting magnetic control system for manipulation of particulate matter and magnetic probes in medical and industrial applications

DOEpatents

Cha, Yung Sheng; Hull, John R.; Askew, Thomas R.

2006-07-11

A system and method of controlling movement of magnetic material with at least first and second high temperature superconductors at spaced locations. A plurality of solenoids are associated with the superconductors to induce a persistent currents in preselected high temperature superconductors establishing a plurality of magnetic fields in response to pulsed currents introduced to one or more of the solenoids. Control mechanism in communication with said solenoids and/or said high temperature superconductors are used to demagnetize selected ones of the high temperature superconductors to reduce the magnetic fields substantially to zero. Magnetic material is moved between magnetic fields by establishing the presence thereof and thereafter reducing magnetic fields substantially to zero and establishing magnetic fields in other superconductors arranged in a predetermined configuration.

Synthesizing Biomolecule-based Boolean Logic Gates

PubMed Central

Miyamoto, Takafumi; Razavi, Shiva; DeRose, Robert; Inoue, Takanari

2012-01-01

One fascinating recent avenue of study in the field of synthetic biology is the creation of biomolecule-based computers. The main components of a computing device consist of an arithmetic logic unit, the control unit, memory, and the input and output devices. Boolean logic gates are at the core of the operational machinery of these parts, hence to make biocomputers a reality, biomolecular logic gates become a necessity. Indeed, with the advent of more sophisticated biological tools, both nucleic acid- and protein-based logic systems have been generated. These devices function in the context of either test tubes or living cells and yield highly specific outputs given a set of inputs. In this review, we discuss various types of biomolecular logic gates that have been synthesized, with particular emphasis on recent developments that promise increased complexity of logic gate circuitry, improved computational speed, and potential clinical applications. PMID:23526588

Logic models to predict continuous outputs based on binary inputs with an application to personalized cancer therapy

PubMed Central

Knijnenburg, Theo A.; Klau, Gunnar W.; Iorio, Francesco; Garnett, Mathew J.; McDermott, Ultan; Shmulevich, Ilya; Wessels, Lodewyk F. A.

2016-01-01

Mining large datasets using machine learning approaches often leads to models that are hard to interpret and not amenable to the generation of hypotheses that can be experimentally tested. We present ‘Logic Optimization for Binary Input to Continuous Output’ (LOBICO), a computational approach that infers small and easily interpretable logic models of binary input features that explain a continuous output variable. Applying LOBICO to a large cancer cell line panel, we find that logic combinations of multiple mutations are more predictive of drug response than single gene predictors. Importantly, we show that the use of the continuous information leads to robust and more accurate logic models. LOBICO implements the ability to uncover logic models around predefined operating points in terms of sensitivity and specificity. As such, it represents an important step towards practical application of interpretable logic models. PMID:27876821

Synthesizing biomolecule-based Boolean logic gates.

PubMed

Miyamoto, Takafumi; Razavi, Shiva; DeRose, Robert; Inoue, Takanari

2013-02-15

One fascinating recent avenue of study in the field of synthetic biology is the creation of biomolecule-based computers. The main components of a computing device consist of an arithmetic logic unit, the control unit, memory, and the input and output devices. Boolean logic gates are at the core of the operational machinery of these parts, and hence to make biocomputers a reality, biomolecular logic gates become a necessity. Indeed, with the advent of more sophisticated biological tools, both nucleic acid- and protein-based logic systems have been generated. These devices function in the context of either test tubes or living cells and yield highly specific outputs given a set of inputs. In this review, we discuss various types of biomolecular logic gates that have been synthesized, with particular emphasis on recent developments that promise increased complexity of logic gate circuitry, improved computational speed, and potential clinical applications.

Logic models to predict continuous outputs based on binary inputs with an application to personalized cancer therapy.

PubMed

Knijnenburg, Theo A; Klau, Gunnar W; Iorio, Francesco; Garnett, Mathew J; McDermott, Ultan; Shmulevich, Ilya; Wessels, Lodewyk F A

2016-11-23

Mining large datasets using machine learning approaches often leads to models that are hard to interpret and not amenable to the generation of hypotheses that can be experimentally tested. We present 'Logic Optimization for Binary Input to Continuous Output' (LOBICO), a computational approach that infers small and easily interpretable logic models of binary input features that explain a continuous output variable. Applying LOBICO to a large cancer cell line panel, we find that logic combinations of multiple mutations are more predictive of drug response than single gene predictors. Importantly, we show that the use of the continuous information leads to robust and more accurate logic models. LOBICO implements the ability to uncover logic models around predefined operating points in terms of sensitivity and specificity. As such, it represents an important step towards practical application of interpretable logic models.

[Processes of logical thought in a case of cerebral vascular lesion].

PubMed

Blanco Men ndez, R; Aguado Balsas, A M

Reasoning and logical thought processes have traditionally been attributed to frontal lobe function or,on the other hand, have been considered as diffuse functions of the brain. However, there is today evidence enough about the possibility to find dissociations in thought processes, depending on logical structure of the experimental tasks and referring to different areas of the brain, frontal and post rolandic ones. To study possible dissociations between thought structures corresponding to categorical and relational logic, on one hand, and propositional logic on the other hand. The case of a brain injured patient with vascular etiology, localized in left frontal parietal cortex, is presented. A specific battery of reasoning tests has been administered. . A differential performance at some reasoning experimental tasks has been found depending on such logical conceptual structures. The possibility of establishing dissociations among certain logical thought and intelectual functions depending on localization of possible brain lesion (frontal versus temporal) is discussed.

Dynamical Tests in a Linear Superconducting Magnetic Bearing

NASA Astrophysics Data System (ADS)

Dias, D. H. N.; Sotelo, G. G.; Sass, F.; Motta, E. S.; , R. de Andrade, Jr.; Stephan, R. M.

The unique properties of high critical temperature superconductors (HTS) make possible the development of an effective and self-stable magnetic levitation (MagLev) transportation system. In this context, a full scale MagLev vehicle, named MagLev-Cobra, has been developed at the Laboratory for Applied Superconductivity (LASUP/UFRJ). The vehicle is borne by a linear superconducting magnetic bearing (LSMB). The most important design constraint of the levitation system is the force that appears due to the interaction between the HTS and the permanent magnetic (PM) rail, which composes the LSMB. Static and dynamic characteristics of this force must be studied. The static behavior was already reported in previous work. The dynamic operation of this kind of vehicle, which considers the entry and exit of passengers and vibration movements, may result in the decrease of the gap between the superconductor and the PM rail in LSMB. In order to emulate the vehicle operation and to study the gap variation with time, the superconductors are submitted to a series of vertical displacements performed with the help of an experimental test rig. These movements are controlled by a time-variant reference force that reproduces the vehicle dynamic. In the present work, the results obtained for the dynamic gap behavior are presented. These measurements are essential to the commissioning process of a superconducting MagLev full scale vehicle.

Manufacturing and test of 2G-HTS coils for rotating machines: Challenges, conductor requirements, realization

NASA Astrophysics Data System (ADS)

Oomen, Marijn; Herkert, Werner; Bayer, Dietmar; Kummeth, Peter; Nick, Wolfgang; Arndt, Tabea

2012-11-01

We investigate the use of 2nd-generation High-Temperature Superconductors (2G-HTSs) in the rotors of electrical motors and generators. For these devices the conductor must be wound into robust impregnated coils, which are operated in vacuum at temperatures around 30 K, in strong magnetic fields of about 2T. Differences in thermal contraction between the coil former, conductor constituents, impregnation resin, bandage and heat-sink materials (assembled at room temperature) cause mechanical stresses at operating temperature. Rotating-machine operation adds Lorentz forces and challenging centripetal accelerations up to thousands of g. Second generation-HTS conductors withstand large tensile stresses in axial direction and compression in normal direction. However, shear stresses, axial compression, and tension normal to the conductor can cause degradation in superconducting properties. Such stresses can be mitigated by correct choice of materials, coil lay-out and manufacturing process. A certain stress level will remain, which the conductor must withstand. We have manufactured many impregnated round and race-track coils, using different 2G-HTS conductors, and tested them at temperatures from 25 K to 77 K. Degradation of the superconductor in early coils was traced to the mentioned differences in thermal contraction, and was completely avoided in coils produced later. We will discuss appropriate coil-winding techniques to assure robust and reliable superconductor performance.

Determination of spin polarization using an unconventional iron superconductor

DOE PAGES

Gifford, J. A.; Chen, B. B.; Zhang, J.; ...

2016-11-21

Here, an unconventional iron superconductor, SmO 0.7F 0.3FeAs, has been utilized to determine the spin polarization and temperature dependence of a highly spin-polarized material, La 0.67Sr 0.33MnO 3, with Andreev reflection spectroscopy. The polarization value obtained is the same as that determined using a conventional superconductor Pb but the temperature dependence of the spin polarization can be measured up to 52 K, a temperature range, which is several times wider than that using a typical conventional superconductor. The result excludes spin-parallel triplet pairing in the iron superconductor.

Epitaxial heterojunctions of oxide semiconductors and metals on high temperature superconductors

NASA Technical Reports Server (NTRS)

Vasquez, Richard P. (Inventor); Hunt, Brian D. (Inventor); Foote, Marc C. (Inventor)

1994-01-01

Epitaxial heterojunctions formed between high temperature superconductors and metallic or semiconducting oxide barrier layers are provided. Metallic perovskites such as LaTiO3, CaVO3, and SrVO3 are grown on electron-type high temperature superconductors such as Nd(1.85)Ce(0.15)CuO(4-x). Alternatively, transition metal bronzes of the form A(x)MO(3) are epitaxially grown on electron-type high temperature superconductors. Also, semiconducting oxides of perovskite-related crystal structures such as WO3 are grown on either hole-type or electron-type high temperature superconductors.

Superconductor rotor cooling system

DOEpatents

Gamble, Bruce B.; Sidi-Yekhlef, Ahmed; Schwall, Robert E.; Driscoll, David I.; Shoykhet, Boris A.

2004-11-02

A system for cooling a superconductor device includes a cryocooler located in a stationary reference frame and a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with a rotating reference frame in which the superconductor device is located. A method of cooling a superconductor device includes locating a cryocooler in a stationary reference frame, and transferring heat from a superconductor device located in a rotating reference frame to the cryocooler through a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with the rotating reference frame.

Superconductor rotor cooling system

DOEpatents

Gamble, Bruce B.; Sidi-Yekhlef, Ahmed; Schwall, Robert E.; Driscoll, David I.; Shoykhet, Boris A.

2002-01-01

A system for cooling a superconductor device includes a cryocooler located in a stationary reference frame and a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with a rotating reference frame in which the superconductor device is located. A method of cooling a superconductor device includes locating a cryocooler in a stationary reference frame, and transferring heat from a superconductor device located in a rotating reference frame to the cryocooler through a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with the rotating reference frame.

Evidence that logical reasoning depends on conscious processing.

PubMed

DeWall, C Nathan; Baumeister, Roy F; Masicampo, E J

2008-09-01

Humans, unlike other animals, are equipped with a powerful brain that permits conscious awareness and reflection. A growing trend in psychological science has questioned the benefits of consciousness, however. Testing a hypothesis advanced by [Lieberman, M. D., Gaunt, R., Gilbert, D. T., & Trope, Y. (2002). Reflection and reflexion: A social cognitive neuroscience approach to attributional inference. Advances in Experimental Social Psychology, 34, 199-249], four studies suggested that the conscious, reflective processing system is vital for logical reasoning. Substantial decrements in logical reasoning were found when a cognitive load manipulation preoccupied conscious processing, while hampering the nonconscious system with consciously suppressed thoughts failed to impair reasoning (Experiment 1). Nonconscious activation (priming) of the idea of logical reasoning increased the activation of logic-relevant concepts, but failed to improve logical reasoning performance (Experiments 2a-2c) unless the logical conclusions were largely intuitive and thus not reliant on logical reasoning (Experiment 3). Meanwhile, stimulating the conscious goal of reasoning well led to improvements in reasoning performance (Experiment 4). These findings offer evidence that logical reasoning is aided by the conscious, reflective processing system.

Cooper pair splitter realized in a two-quantum-dot Y-junction.

PubMed

Hofstetter, L; Csonka, S; Nygård, J; Schönenberger, C

2009-10-15

Non-locality is a fundamental property of quantum mechanics that manifests itself as correlations between spatially separated parts of a quantum system. A fundamental route for the exploration of such phenomena is the generation of Einstein-Podolsky-Rosen (EPR) pairs of quantum-entangled objects for the test of so-called Bell inequalities. Whereas such experimental tests of non-locality have been successfully conducted with pairwise entangled photons, it has not yet been possible to realize an electronic analogue of it in the solid state, where spin-1/2 mobile electrons are the natural quantum objects. The difficulty stems from the fact that electrons are immersed in a macroscopic ground state-the Fermi sea-which prevents the straightforward generation and splitting of entangled pairs of electrons on demand. A superconductor, however, could act as a source of EPR pairs of electrons, because its ground-state is composed of Cooper pairs in a spin-singlet state. These Cooper pairs can be extracted from a superconductor by tunnelling, but, to obtain an efficient EPR source of entangled electrons, the splitting of the Cooper pairs into separate electrons has to be enforced. This can be achieved by having the electrons 'repel' each other by Coulomb interaction. Controlled Cooper pair splitting can thereby be realized by coupling of the superconductor to two normal metal drain contacts by means of individually tunable quantum dots. Here we demonstrate the first experimental realization of such a tunable Cooper pair splitter, which shows a surprisingly high efficiency. Our findings open a route towards a first test of the EPR paradox and Bell inequalities in the solid state.

In situ/non-contact superfluid density measurement apparatus

NASA Astrophysics Data System (ADS)

Nam, Hyoungdo; Su, Ping-Hsang; Shih, Chih-Kang

2018-04-01

We present a double-coil apparatus designed to operate with in situ capability, which is strongly desired for superconductivity studies on recently discovered two-dimensional superconductors. Coupled with a scanning tunneling microscope, the study of both local and global superconductivity [for superconducting gap and superfluid density (SFD), respectively] is possible on an identical sample without sample degradations due to damage, contamination, or oxidation in an atmosphere. The performance of the double-coil apparatus was tested on atomically clean surfaces of non-superconducting Si(111)-7 × 7 and on superconducting films of 100 nm-thick Pb and 1.4 nm-ultrathin Pb. The results clearly show the normal-to-superconductor phase transition for Pb films with a strong SFD.

Effect of an applied magnetic field on the performance of a SIS receiver near 300 GHz

NASA Technical Reports Server (NTRS)

Mallison, W. H.; De Zafra, R. L.

1992-01-01

A superconductor-insulator-superconductor (SIS) receiver has been successfully constructed and tested for operation at 265 - 280 GHz using 1 micron/sq area Nb-AlO(x)-Nb tunnel junctions fabricated at Stony Brook. The best performance to date is a double sideband (DSB) receiver noise temperature of 129 K at 278 GHz. It is found that suppression of the Josephson pair currents with a magnetic field is essential for good performance and a stable dc bias point. Fields as high as 280 gauss have been used with no degradation of mixing performance. The improvement in the intermediate frequency output stability with progressively increasing magnetic fields is illustrated.

Submicron Systems Architecture Project

DTIC Science & Technology

1981-11-01

This project is concerned with the architecture , design , and testing of VLSI Systems. The principal activities in this report period include: The Tree Machine; COPE, The Homogeneous Machine; Computational Arrays; Switch-Level Model for MOS Logic Design; Testing; Local Network and Designer Workstations; Self-timed Systems; Characterization of Deadlock Free Resource Contention; Concurrency Algebra; Language Design and Logic for Program Verification.

Processing of Mixed Oxide Superconductors

DTIC Science & Technology

1990-07-01

rapid changes world wide a major research centre on high Tc superconductors was awarded to Cambridge which involved moving the work and people to a...reports and paper is in the appendices. Separation Ceramic superconductors tend to be mixtures of phases, especially when first discovered. It would...properties of the superconducting state will in principle allow superconducting material to be levitated from the non superconductor and several designs

Microwave Resonators and Filters

DTIC Science & Technology

2015-12-22

endorsed by the United States Government. 2 Equation Chapter 1 Section 1Introduction Why use superconductors ? Although superconductors have zero...explained in other chapters, the surface resistance of superconductors at microwave frequencies can be as much as three orders of magnitude lower than the...for the use of superconductors in many applications, such as in high performance filters, is low loss even in a very small size. The energy stored is

Ambient-temperature superconductor symetrical metal-dihalide bis-(ethylenedithio)-tetrathiafulvalene compounds

DOEpatents

Williams, Jack M.; Wang, Hsien-Hau; Beno, Mark A.

1987-01-01

A new class of organic superconductors having the formula (ET).sub.2 MX.sub.2 wherein ET represents bis(ethylenedithio)-tetrathiafulvalene, M is a metal such as Au, Ag, In, Tl, Rb, Pd and the like and X is a halide. The superconductor (ET).sub.2 AuI.sub.2 exhibits a transition temperature of 5 K. which is high for organic superconductors.

How to detect fluctuating stripes in the high-temperature superconductors

NASA Astrophysics Data System (ADS)

Kivelson, S. A.; Bindloss, I. P.; Fradkin, E.; Oganesyan, V.; Tranquada, J. M.; Kapitulnik, A.; Howald, C.

2003-10-01

This article discusses fluctuating order in a quantum disordered phase proximate to a quantum critical point, with particular emphasis on fluctuating stripe order. Optimal strategies are derived for extracting information concerning such local order from experiments, with emphasis on neutron scattering and scanning tunneling microscopy. These ideas are tested by application to two model systems—an exactly solvable one-dimensional (1D) electron gas with an impurity, and a weakly interacting 2D electron gas. Experiments on the cuprate high-temperature superconductors which can be analyzed using these strategies are extensively reviewed. The authors adduce evidence that stripe correlations are widespread in the cuprates. They compare and contrast the advantages of two limiting perspectives on the high-temperature superconductor: weak coupling, in which correlation effects are treated as a perturbation on an underlying metallic (although renormalized) Fermi-liquid state, and strong coupling, in which the magnetism is associated with well-defined localized spins, and stripes are viewed as a form of micro phase separation. The authors present quantitative indicators that the latter view better accounts for the observed stripe phenomena in the cuprates.

Out-of-equilibrium spin transport in mesoscopic superconductors.

PubMed

Quay, C H L; Aprili, M

2018-08-06

The excitations in conventional superconductors, Bogoliubov quasi-particles, are spin-[Formula: see text] fermions but their charge is energy-dependent and, in fact, zero at the gap edge. Therefore, in superconductors (unlike normal metals) spin and charge degrees of freedom may be separated. In this article, we review spin injection into conventional superconductors and focus on recent experiments on mesoscopic superconductors. We show how quasi-particle spin transport and out-of-equilibrium spin-dependent superconductivity can be triggered using the Zeeman splitting of the quasi-particle density of states in thin-film superconductors with small spin-mixing scattering. Finally, we address the spin dynamics and the feedback of quasi-particle spin imbalances on the amplitude of the superconducting energy gap.This article is part of the theme issue 'Andreev bound states'. © 2018 The Author(s).

Precursor composites for oxygen dispersion hardened silver sheathed superconductor composites

DOEpatents

Podtburg, E.R.

1999-06-22

An oxide superconductor composite having improved texture and durability is disclosed. The oxide superconductor composite includes an oxide superconductor phase substantially surrounded with/by a noble metal matrix, the noble metal matrix comprising a metal oxide in an amount effective to form metal oxide domains that increase hardness of the composite. The composite is characterized by a degree of texture at least 10% greater than a comparable oxide superconductor composite lacking metal oxide domains. An oxide superconducting composite may be prepared by oxidizing the precursor composite under conditions effective to form solute metal oxide domains within the silver matrix and to form a precursor oxide in the precursor alloy phase; subjecting the oxidized composite to a softening anneal under conditions effective to relieve stress within the noble metal phase; and converting the oxide precursor into an oxide superconductor. 1 fig.

Precursor composites for oxygen dispersion hardened silver sheathed superconductor composites

DOEpatents

Podtburg, Eric R.

1999-01-01

An oxide superconductor composite having improved texture and durability. The oxide superconductor composite includes an oxide superconductor phase substantially surrounded with/by a noble metal matrix, the noble metal matrix comprising a metal oxide in an amount effective to form metal oxide domains that increase hardness of the composite. The composite is characterized by a degree of texture at least 10% greater than a comparable oxide superconductor composite lacking metal oxide domains. An oxide superconducting composite may be prepared by oxidizing the precursor composite under conditions effective to form solute metal oxide domains within the silver matrix and to form a precursor oxide in the precursor alloy phase; subjecting the oxidized composite to a softening anneal under conditions effective to relieve stress within the noble metal phase; and converting the oxide precursor into an oxide superconductor.

Improvement in trapped fields by stacking bulk superconductors

NASA Astrophysics Data System (ADS)

Suzuki, A.; Wongsatanawarid, A.; Seki, H.; Murakami, M.

2009-10-01

We studied the effects of stacking several bulk superconductor blocks on the field trapping properties. In order to avoid the detrimental effects of the bottom deteriorated parts, bulk Dy-Ba-Cu-O superconductors 45 mm in diameter and 10 mm in thickness were cut from the top parts of as-grown bulk blocks of 25 mm diameter. We stacked the superconductors and measured the field distribution as a function of the gap. The trapped field measurements were performed by field-cooling the samples inserted in between two permanent magnets with liquid nitrogen. It was found that the trapped field values are almost doubled when the number of stacked bulk superconductors increased from two to three. The present results clearly show that one can expect beneficial effects of increasing the ratio of the height to the diameter even in bulk high temperature superconductors.

Proposal of Magnetic Circuit using Magnetic Shielding with Bulk-Type High Tc Superconductors

NASA Astrophysics Data System (ADS)

Fukuoka, Katsuhiro; Hashimoto, Mitsuo; Tomita, Masaru; Murakami, Masato

Recently, bulk-type high Tc superconductors having a characteristic of critical current density over 104 A/cm2 in liquid nitrogen temperature (77K) on 1T, can be produced. They are promising for many practical applications such as a magnetic bearing, a magnetic levitation, a flywheel, a magnetic shielding and others. In this research, we propose a magnetic circuit that is able to use for the magnetic shield of plural superconductors as an application of bulk-type high Tc superconductors. It is a closed magnetic circuit by means of a toroidal core. Characteristics of the magnetic circuit surrounded with superconductors are evaluated and the possibility is examined. As the magnetic circuit of the ferrite core is surrounded with superconductors, the magnetic flux is shielded even if it leaked from the ferrite core.

Techniques for Connecting Superconducting Thin Films

NASA Technical Reports Server (NTRS)

Mester, John; Gwo, Dz-Hung

2006-01-01

Several improved techniques for connecting superconducting thin films on substrates have been developed. The techniques afford some versatility for tailoring the electronic and mechanical characteristics of junctions between superconductors in experimental electronic devices. The techniques are particularly useful for making superconducting or alternatively normally conductive junctions (e.g., Josephson junctions) between patterned superconducting thin films in order to exploit electron quantum-tunneling effects. The techniques are applicable to both low-Tc and high-Tc superconductors (where Tc represents the superconducting- transition temperature of a given material), offering different advantages for each. Most low-Tc superconductors are metallic, and heretofore, connections among them have been made by spot welding. Most high-Tc superconductors are nonmetallic and cannot be spot welded. These techniques offer alternatives to spot welding of most low-Tc superconductors and additional solutions to problems of connecting most high-Tc superconductors.

Electromechanical properties of superconductors for DOE fusion applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ekin, J.W.; Moreland, J.; Brauch, J.C.

1986-03-01

This is an interim report presenting data on superconductor performance under mechanical load, which are needed for the selection of superconductors and the mechanical design of superconducting magnets for DOE fusion energy systems. A further aim of the reported research is to measure and understand the electromechanical properties of promising new superconductor materials with strong application potential at high magnetic fields. Results include the following. The first strain vs. critical-current studies were made on a Chevrel-phase superconductor, PbMo/sub 6/S/sub 8/. Chevrel-phase superconductors were found to have a large strain effect, comparable in magnitude to A-15 superconductors like Nb/sub 3/Sn. Electromechanical-propertymore » measurements of an experimental liquid-tin-infiltrated Nb/sub 3/Sn conductor showed it to have an irreversible strain limit twice as large as bronze-process supercondutors and a significantly higher overall critical-current denstiy; the liquid-infiltration process thus has the potential for development of a practical Nb/sub 3/Sn conductors with both superior critical-current density and extremely good mechanical properties. Electromechanical parameters were obtained on several Nb/sub 3/Sn conductors that are candidate materials for superconducting fusion magnets, icluding conductors fabricated by the bronze, internal-tin, and jelly-roll processes. Thermal contraction data are reported on several new structural materials for superconductor sheathing and reinforcement, and a new diagnostic tool for probing the energy gap of practical superconductors has been developed using electron tunneling.« less

Multi-layer articles and methods of making same

DOEpatents

Fritzemeier, Leslie G.; Zhang, Wei; Palm, Walter C.; Rupich, Martin W.

2005-05-17

The invention relates to superconductor articles, and compositions and methods for making superconductor articles. The methods can include using a precursor solution having a relatively small concentration of total free acid. The articles can include more than one layer of superconductor material in which at least one layer of superconductor material can be formed by a solution process, such as a solution process involving the use of metalorganic precursors.

Low resistivity contact to iron-pnictide superconductors

DOEpatents

Tanatar, Makariy; Prozorov, Ruslan; Ni, Ni; Bud& #x27; ko, Sergey; Canfield, Paul

2013-05-28

Method of making a low resistivity electrical connection between an electrical conductor and an iron pnictide superconductor involves connecting the electrical conductor and superconductor using a tin or tin-based material therebetween, such as using a tin or tin-based solder. The superconductor can be based on doped AFe.sub.2As.sub.2, where A can be Ca, Sr, Ba, Eu or combinations thereof for purposes of illustration only.

Passivation Of High-Temperature Superconductors

NASA Technical Reports Server (NTRS)

Vasquez, Richard P.

1991-01-01

Surfaces of high-temperature superconductors passivated with native iodides, sulfides, or sulfates formed by chemical treatments after superconductors grown. Passivating compounds nearly insoluble in and unreactive with water and protect underlying superconductors from effects of moisture. Layers of cuprous iodide and of barium sulfate grown. Other candidate passivating surface films: iodides and sulfides of bismuth, strontium, and thallium. Other proposed techniques for formation of passivating layers include deposition and gas-phase reaction.

A Thermally Actuated Flux Pump for Energizing YBCO Pucks

DTIC Science & Technology

2016-05-01

transmitted through the thermal magnetic material sweeping magnetic field lines into the superconducting puck. We used YBCO as the superconductor with...of the YBCO sweeping vortices into the superconductor . These vortices would gradually accumulate in the superconductor . Successes have been reported...superconducting flux pump,” PHYSICA C, vol. 468, pp. 153-159, 2008. [2] T. A. Coombs, Z. Hong, Y. Yan and C. D. Rawlings, “ Superconductors : The

Design and Demonstration of a 30 GHz 16-bit Superconductor RSFQ Microprocessor

DTIC Science & Technology

2015-03-10

for Public Release; Distribution Unlimited Final Report: Design and Demonstration of a 30 GHz 16-bit Superconductor RSFQ Microprocessor The views...P.O. Box 12211 Research Triangle Park, NC 27709-2211 Superconductor technology, RSFQ, RQL, processor design, arithmetic units, high-performance...Demonstration of a 30 GHz 16-bit Superconductor RSFQ Microprocessor Report Title The major objective of the project was to design and demonstrate operation

Improved ambient-pressure organic superconductor. [Bis(ethylenedithio)TTF-MX/sub 2/

DOEpatents

Williams, J.M.; Wang, Hsien-Hau; Beno, M.A.

1985-05-29

Disclosed is a new class of organic superconductors having the formula (ET)/sub 2/MX/sub 2/ wherein ET represents bis(ethylenedithio)-tetrathiafulvalene, M is a metal such as Au, Ag, In, Tl, Rb, Pd and the like and X is a halide. The superconductor (ET)/sub 2/AuI/sub 2/ exhibits a transition temperature of 5/sup 0/K which is high for organic superconductors.

Realization of High-temperature Superconductivity in Nano-carbon Materials and Its Application

DTIC Science & Technology

2015-07-13

hottest topics in condensed matter physics and also for application to zero- emission energy system. In particular, carbon-based superconductors have...ernission energy system. In particular, carbon-based superconductors have attracted significant attention for high transition temperature (T c). In...e-based superconductors have previously shown T c > 40K among various superconductors . In particular, carbon-base new SC exhibited T c < 20K in any

GaN/NbN epitaxial semiconductor/superconductor heterostructures

NASA Astrophysics Data System (ADS)

Yan, Rusen; Khalsa, Guru; Vishwanath, Suresh; Han, Yimo; Wright, John; Rouvimov, Sergei; Katzer, D. Scott; Nepal, Neeraj; Downey, Brian P.; Muller, David A.; Xing, Huili G.; Meyer, David J.; Jena, Debdeep

2018-03-01

Epitaxy is a process by which a thin layer of one crystal is deposited in an ordered fashion onto a substrate crystal. The direct epitaxial growth of semiconductor heterostructures on top of crystalline superconductors has proved challenging. Here, however, we report the successful use of molecular beam epitaxy to grow and integrate niobium nitride (NbN)-based superconductors with the wide-bandgap family of semiconductors—silicon carbide, gallium nitride (GaN) and aluminium gallium nitride (AlGaN). We apply molecular beam epitaxy to grow an AlGaN/GaN quantum-well heterostructure directly on top of an ultrathin crystalline NbN superconductor. The resulting high-mobility, two-dimensional electron gas in the semiconductor exhibits quantum oscillations, and thus enables a semiconductor transistor—an electronic gain element—to be grown and fabricated directly on a crystalline superconductor. Using the epitaxial superconductor as the source load of the transistor, we observe in the transistor output characteristics a negative differential resistance—a feature often used in amplifiers and oscillators. Our demonstration of the direct epitaxial growth of high-quality semiconductor heterostructures and devices on crystalline nitride superconductors opens up the possibility of combining the macroscopic quantum effects of superconductors with the electronic, photonic and piezoelectric properties of the group III/nitride semiconductor family.

GaN/NbN epitaxial semiconductor/superconductor heterostructures.

PubMed

Yan, Rusen; Khalsa, Guru; Vishwanath, Suresh; Han, Yimo; Wright, John; Rouvimov, Sergei; Katzer, D Scott; Nepal, Neeraj; Downey, Brian P; Muller, David A; Xing, Huili G; Meyer, David J; Jena, Debdeep

2018-03-07

Epitaxy is a process by which a thin layer of one crystal is deposited in an ordered fashion onto a substrate crystal. The direct epitaxial growth of semiconductor heterostructures on top of crystalline superconductors has proved challenging. Here, however, we report the successful use of molecular beam epitaxy to grow and integrate niobium nitride (NbN)-based superconductors with the wide-bandgap family of semiconductors-silicon carbide, gallium nitride (GaN) and aluminium gallium nitride (AlGaN). We apply molecular beam epitaxy to grow an AlGaN/GaN quantum-well heterostructure directly on top of an ultrathin crystalline NbN superconductor. The resulting high-mobility, two-dimensional electron gas in the semiconductor exhibits quantum oscillations, and thus enables a semiconductor transistor-an electronic gain element-to be grown and fabricated directly on a crystalline superconductor. Using the epitaxial superconductor as the source load of the transistor, we observe in the transistor output characteristics a negative differential resistance-a feature often used in amplifiers and oscillators. Our demonstration of the direct epitaxial growth of high-quality semiconductor heterostructures and devices on crystalline nitride superconductors opens up the possibility of combining the macroscopic quantum effects of superconductors with the electronic, photonic and piezoelectric properties of the group III/nitride semiconductor family.

Electronic structure, irreversibility line and magnetoresistance of Cu 0.3Bi 2Se 3 superconductor

DOE PAGES

Hemian, Yi; Gu, Genda; Chen, Chao -Yu; ...

2015-06-01

Cu xBi 2Se 3 is a superconductor that is a potential candidate for topological superconductors. We report our laser-based angle-resolved photoemission measurement on the electronic structure of the Cu xBi 2Se 3 superconductor, and a detailed magneto-resistance measurement in both normal and superconducting states. We find that the topological surface state of the pristine Bi 2Se 3 topological insulator remains robust after the Cu-intercalation, while the Dirac cone location moves downward due to electron doping. Detailed measurements on the magnetic field-dependence of the resistance in the superconducting state establishes an irreversibility line and gives a value of the upper criticalmore » field at zero temperature of ~4000 Oe for the Cu 0.3Bi 2Se 3 superconductor with a middle point T c of 1.9K. The relation between the upper critical field Hc2 and temperature T is different from the usual scaling relation found in cuprates and in other kinds of superconductors. Small positive magneto-resistance is observed in Cu 0.3Bi 2Se 3 superconductors up to room temperature. As a result, these observations provide useful information for further study of this possible candidate for topological superconductors.« less

Method and apparatus to trigger superconductors in current limiting devices

DOEpatents

Yuan, Xing; Hazelton, Drew Willard; Walker, Michael Stephen

2004-10-26

A method and apparatus for magnetically triggering a superconductor in a superconducting fault current limiter to transition from a superconducting state to a resistive state. The triggering is achieved by employing current-carrying trigger coil or foil on either or both the inner diameter and outer diameter of a superconductor. The current-carrying coil or foil generates a magnetic field with sufficient strength and the superconductor is disposed within essentially uniform magnetic field region. For superconductor in a tubular-configured form, an additional magnetic field can be generated by placing current-carrying wire or foil inside the tube and along the center axial line.

Stress analysis in high-temperature superconductors under pulsed field magnetization

NASA Astrophysics Data System (ADS)

Wu, Haowei; Yong, Huadong; Zhou, Youhe

2018-04-01

Bulk high-temperature superconductors (HTSs) have a high critical current density and can trap a large magnetic field. When bulk superconductors are magnetized by the pulsed field magnetization (PFM) technique, they are also subjected to a large electromagnetic stress, and the resulting thermal stress may cause cracking of the superconductor due to the brittle nature of the sample. In this paper, based on the H-formulation and the law of heat transfer, we can obtain the distributions of electromagnetic field and temperature, which are in qualitative agreement with experiment. After that, based on the dynamic equilibrium equations, the mechanical response of the bulk superconductor is determined. During the PFM process, the change in temperature has a dramatic effect on the radial and hoop stresses, and the maximum radial and hoop stress are 24.2 {{MPa}} and 22.6 {{MPa}}, respectively. The mechanical responses of a superconductor for different cases are also studied, such as the peak value of the applied field and the size of bulk superconductors. Finally, the stresses are also presented for different magnetization methods.

Interaction between fractional Josephson vortices in multi-gap superconductor tunnel junctions

NASA Astrophysics Data System (ADS)

Kim, Ju H.

In a long Josephson junction (LJJ) with two-band superconductors, fractionalization of Josephson vortices (fluxons) can occur in the broken time reversal symmetry state when spatial phase textures (i-solitons) are excited. Excitation of i-solitons in each superconductor layer of the junction, arising due to the presence of two condensates and the interband Josephson effect, leads to spatial variation of the critical current density between the superconductor layers. Similar to the situation in a YBa2 Cu3O7 - x superconductor film grain boundary, this spatial dependence of the crtitical current density can self-generate magnetic flux in the insulator layer, resulting in fractional fluxons with large and small fraction of flux quantum. Similar to fluxons in one-band superconductor LJJ, these fractional fluxons are found to interact with each other. The interaction between large and small fractional fluxons determines the size of a fluxon which includes two (one large and one small) fractional fluxons. We discuss the nature of interaction between fractional fluxons and suggest that i-soliton excitations in multi-gap superconductor LJJs may be probed by using magnetic flux measurements.

Medical Students' vs. Family Physicians' Assessment of Practical and Logical Values of Pathophysiology Multiple-Choice Questions

ERIC Educational Resources Information Center

Secic, Damir; Husremovic, Dzenana; Kapur, Eldan; Jatic, Zaim; Hadziahmetovic, Nina; Vojnikovic, Benjamin; Fajkic, Almir; Meholjic, Amir; Bradic, Lejla; Hadzic, Amila

2017-01-01

Testing strategies can either have a very positive or negative effect on the learning process. The aim of this study was to examine the degree of consistency in evaluating the practicality and logic of questions from a medical school pathophysiology test, between students and family medicine doctors. The study engaged 77 family medicine doctors…

Extended Logic Intelligent Processing System for a Sensor Fusion Processor Hardware

NASA Technical Reports Server (NTRS)

Stoica, Adrian; Thomas, Tyson; Li, Wei-Te; Daud, Taher; Fabunmi, James

2000-01-01

The paper presents the hardware implementation and initial tests from a low-power, highspeed reconfigurable sensor fusion processor. The Extended Logic Intelligent Processing System (ELIPS) is described, which combines rule-based systems, fuzzy logic, and neural networks to achieve parallel fusion of sensor signals in compact low power VLSI. The development of the ELIPS concept is being done to demonstrate the interceptor functionality which particularly underlines the high speed and low power requirements. The hardware programmability allows the processor to reconfigure into different machines, taking the most efficient hardware implementation during each phase of information processing. Processing speeds of microseconds have been demonstrated using our test hardware.

Evidence of Spin-Injection-Induced Cooper Pair Breaking in Perovskite Ferromagnet-Insulator-Superconductor Heterostructures via Pulsed Current Measurements

NASA Technical Reports Server (NTRS)

Yeh, N. C.; Samoilov, A. V.; Veasquez, R. P.; Li, Y.

1998-01-01

The effect of spin-polarized currents on the critical current densities of cuprate superconductors is investigated in perovskite ferromagnet-insulator-superconductor heterostructures with a pulsed current technique.

Fine uniform filament superconductors

DOEpatents

Riley, Jr., Gilbert N.; Li, Qi; Roberts, Peter R.; Antaya, Peter D.; Seuntjens, Jeffrey M.; Hancock, Steven; DeMoranville, Kenneth L.; Christopherson, Craig J.; Garrant, Jennifer H.; Craven, Christopher A.

2002-01-01

A multifilamentary superconductor composite having a high fill factor is formed from a plurality of stacked monofilament precursor elements, each of which includes a low density superconductor precursor monofilament. The precursor elements all have substantially the same dimensions and characteristics, and are stacked in a rectilinear configuration and consolidated to provide a multifilamentary precursor composite. The composite is thereafter thermomechanically processed to provide a superconductor composite in which each monofilament is less than about 50 microns thick.

Self-triggering superconducting fault current limiter

DOEpatents

Yuan, Xing [Albany, NY; Tekletsadik, Kasegn [Rexford, NY

2008-10-21

A modular and scaleable Matrix Fault Current Limiter (MFCL) that functions as a "variable impedance" device in an electric power network, using components made of superconducting and non-superconducting electrically conductive materials. The matrix fault current limiter comprises a fault current limiter module that includes a superconductor which is electrically coupled in parallel with a trigger coil, wherein the trigger coil is magnetically coupled to the superconductor. The current surge doing a fault within the electrical power network will cause the superconductor to transition to its resistive state and also generate a uniform magnetic field in the trigger coil and simultaneously limit the voltage developed across the superconductor. This results in fast and uniform quenching of the superconductors, significantly reduces the burnout risk associated with non-uniformity often existing within the volume of superconductor materials. The fault current limiter modules may be electrically coupled together to form various "n" (rows).times."m" (columns) matrix configurations.

Analysis of current distribution in a large superconductor

NASA Astrophysics Data System (ADS)

Hamajima, Takataro; Alamgir, A. K. M.; Harada, Naoyuki; Tsuda, Makoto; Ono, Michitaka; Takano, Hirohisa

An imbalanced current distribution which is often observed in cable-in-conduit (CIC) superconductors composed of multistaged, triplet type sub-cables, can deteriorate the performance of the coils. It is, hence very important to analyze the current distribution in a superconductor and find out methods to realize a homogeneous current distribution in the conductor. We apply magnetic flux conservation in a loop contoured by electric center lines of filaments in two arbitrary strands located on adjacent layers in a coaxial multilayer superconductor, and thereby analyze the current distribution in the conductor. A generalized formula governing the current distribution can be described as explicit functions of the superconductor construction parameters, such as twist pitch, twist direction and radius of individual layer. We numerically analyze a homogeneous current distribution as a function of the twist pitches of layers, using the fundamental formula. Moreover, it is demonstrated that we can control current distribution in the coaxial superconductor.

Fractional Josephson vortices in two-gap superconductor long Josephson junctions

NASA Astrophysics Data System (ADS)

Kim, Ju

2014-03-01

We investigated the phase dynamics of long Josephson junctions (LJJ) with two-gap superconductors in the broken time reversal symmetry state. In this LJJ, spatial phase textures (i-solitons) can be excited due to the presence of two condensates and the interband Joesphson effect between them. The presence of a spatial phase texture in each superconductor layer leads to a spatial variation of the critical current density between the superconductor layers. We find that this spatial dependence of the crtitical current density can self-generate magnetic flux in the insulator layer, resulting in Josephson vortices with fractional flux quanta. Similar to the situation in a YBa2 Cu3O7 - x superconductor film grain boundary, the fractionalization of a Josephson vortex arises as a response to either periodic or random excitation of i-solitions. This suggests that magnetic flux measurements may be used to probe i-soliton excitations in multi-gap superconductor LJJs.

Giant supercurrent states in a superconductor-InAs/GaSb-superconductor junction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Xiaoyan, E-mail: xshi@sandia.gov; Pan, W.; Hawkins, S. D.

2015-10-07

Superconductivity in topological materials has attracted a great deal of interest in both electron physics and material sciences since the theoretical predictions that Majorana fermions can be realized in topological superconductors. Topological superconductivity could be realized in a type II, band-inverted, InAs/GaSb quantum well if it is in proximity to a conventional superconductor. Here, we report observations of the proximity effect induced giant supercurrent states in an InAs/GaSb bilayer system that is sandwiched between two superconducting tantalum electrodes to form a superconductor-InAs/GaSb-superconductor junction. Electron transport results show that the supercurrent states can be preserved in a surprisingly large temperature-magnetic fieldmore » (T – H) parameter space. In addition, the evolution of differential resistance in T and H reveals an interesting superconducting gap structure.« less

Rotational response of superconductors: Magnetorotational isomorphism and rotation-induced vortex lattice

NASA Astrophysics Data System (ADS)

Babaev, Egor; Svistunov, Boris

2014-03-01

The analysis of nonclassical rotational response of superfluids and superconductors was performed by Onsager [Onsager, Nuovo Cimento, Suppl. 6, 279 (1949), 10.1007/BF02780991] and London [Superfluids (Wiley, New York, 1950)] and crucially advanced by Feynman [Prog. Low Temp. Phys. 1, 17 (1955), 10.1016/S0079-6417(08)60077-3]. It was established that, in the thermodynamic limit, neutral superfluids rotate by forming—without any threshold—a vortex lattice. In contrast, the rotation of superconductors at angular frequency Ω—supported by uniform magnetic field BL∝Ω due to surface currents—is of the rigid-body type (London law). Here we show that, neglecting the centrifugal effects, the behavior of a rotating superconductor is identical to that of a superconductor placed in a uniform fictitious external magnetic field H ˜=-BL. In particular, the isomorphism immediately implies the existence of two critical rotational frequencies in type-2 superconductors.

Status of high temperature superconductor development for accelerator magnets

NASA Technical Reports Server (NTRS)

Hirabayashi, H.

1995-01-01

High temperature superconductors are still under development for various applications. As far as conductors for magnets are concerned, the development has just been started. Small coils wound by silver sheathed Bi-2212 and Bi-2223 oxide conductors have been reported by a few authors. Essential properties of high T(sub c) superconductors like pinning force, coherent length, intergrain coupling, weak link, thermal property, AC loss and mechanical strength are still not sufficiently understandable. In this talk, a review is given with comparison between the present achievement and the final requirement for high T(sub c) superconductors, which could be particularly used in accelerator magnets. Discussions on how to develop high T(sub c) superconductors for accelerator magnets are included with key parameters of essential properties. A proposal of how to make a prototype accelerator magnet with high T(sub c) superconductors with prospect for future development is also given.

0-π phase-controllable thermal Josephson junction

NASA Astrophysics Data System (ADS)

Fornieri, Antonio; Timossi, Giuliano; Virtanen, Pauli; Solinas, Paolo; Giazotto, Francesco

2017-05-01

Two superconductors coupled by a weak link support an equilibrium Josephson electrical current that depends on the phase difference ϕ between the superconducting condensates. Yet, when a temperature gradient is imposed across the junction, the Josephson effect manifests itself through a coherent component of the heat current that flows opposite to the thermal gradient for |ϕ| < π/2 (refs 2-4). The direction of both the Josephson charge and heat currents can be inverted by adding a π shift to ϕ. In the static electrical case, this effect has been obtained in a few systems, for example via a ferromagnetic coupling or a non-equilibrium distribution in the weak link. These structures opened new possibilities for superconducting quantum logic and ultralow-power superconducting computers. Here, we report the first experimental realization of a thermal Josephson junction whose phase bias can be controlled from 0 to π. This is obtained thanks to a superconducting quantum interferometer that allows full control of the direction of the coherent energy transfer through the junction. This possibility, in conjunction with the completely superconducting nature of our system, provides temperature modulations with an unprecedented amplitude of ∼100 mK and transfer coefficients exceeding 1 K per flux quantum at 25 mK. Then, this quantum structure represents a fundamental step towards the realization of caloritronic logic components such as thermal transistors, switches and memory devices. These elements, combined with heat interferometers and diodes, would complete the thermal conversion of the most important phase-coherent electronic devices and benefit cryogenic microcircuits requiring energy management, such as quantum computing architectures and radiation sensors.

Test Of A Microwave Amplifier With Superconductive Filter

NASA Technical Reports Server (NTRS)

Bhasin, K. B.; Toncich, S. S.; Chorey, C. M.; Bonetti, R. R.; Williams, A. E.

1995-01-01

Report describes design and low-temperature tests of low-noise GaAs microwave amplifier combined with microstrip band-pass filter. Two versions of microstrip filter used in alternate tests; in one version, microstrips formed as films of high-transition-temperature superconductor Y/Ba/Cu/O on lanthanum aluminate substrate with gold film as ground plane. Other version identical except microstrips as well as ground plane made of gold, normally conductive.

Try and Prove It: An Exercise in the Logic of Science.

ERIC Educational Resources Information Center

Bady, Richard J.; Enyeart, Morris A.

1978-01-01

Presents a classroom activity which can be used both to assess student's modes of thought and to clarify the logic of hypothesis testing. The task is based on Piaget's theories of cognitive development. (HM)

C-MOS array design techniques

NASA Technical Reports Server (NTRS)

Feller, A.

1978-01-01

The entire complement of standard cells and components, except for the set-reset flip-flop, was completed. Two levels of checking were performed on each device. Logic cells and topological layout are described. All the related computer programs were coded and one level of debugging was completed. The logic for the test chip was modified and updated. This test chip served as the first test vehicle to exercise the standard cell complementary MOS(C-MOS) automatic artwork generation capability.

A tactile paging system for deaf-blind people, phase 2

NASA Technical Reports Server (NTRS)

Baer, J. A.

1977-01-01

Control logic and the on-body radio transmitter is investigated. The control logic capability and studied methods for implementing the on-body portion of the logic in a small package are improved. A small low power, on-body transmitter was designed, developed, and tested with a wrist-strap antenna to extend the one-way communication system developed during Phase 1 to a two-way communication system.

Design of automata theory of cubical complexes with applications to diagnosis and algorithmic description

NASA Technical Reports Server (NTRS)

Roth, J. P.

1972-01-01

The following problems are considered: (1) methods for development of logic design together with algorithms, so that it is possible to compute a test for any failure in the logic design, if such a test exists, and developing algorithms and heuristics for the purpose of minimizing the computation for tests; and (2) a method of design of logic for ultra LSI (large scale integration). It was discovered that the so-called quantum calculus can be extended to render it possible: (1) to describe the functional behavior of a mechanism component by component, and (2) to compute tests for failures, in the mechanism, using the diagnosis algorithm. The development of an algorithm for the multioutput two-level minimization problem is presented and the program MIN 360 was written for this algorithm. The program has options of mode (exact minimum or various approximations), cost function, cost bound, etc., providing flexibility.

Superconducting Meissner Effect Bearings for Cryogenic Turbomachines. Phase 2

DTIC Science & Technology

1994-02-01

thick melt -grown superconductor...7 Figure 3. Magnetic field in a 1.3 mm thick melt -grown superconductor ............................................... 7 Figure 4. Levitation...force for a 25 mm magnet above a melt -grown superconductor-comparison of model and experiment

Photonic simulation of topological superconductor edge state and zero-energy mode at a vortex

PubMed Central

Tan, Wei; Chen, Liang; Ji, Xia; Lin, Hai-Qing

2014-01-01

Photonic simulations of quantum Hall edge states and topological insulators have inspired considerable interest in recent years. Interestingly, there are theoretical predictions for another type of topological states in topological superconductors, but debates over their experimental observations still remain. Here we investigate the photonic analogue of the px + ipy model of topological superconductor. Two essential characteristics of topological superconductor, particle-hole symmetry and px + ipy pairing potentials, are well emulated in photonic systems. Its topological features are presented by chiral edge state and zero-energy mode at a vortex. This work may fertilize the study of photonic topological states, and open up the possibility for emulating wave behaviors in superconductors. PMID:25488408

Software Safety Assurance of Programmable Logic

NASA Technical Reports Server (NTRS)

Berens, Kalynnda

2002-01-01

Programmable Logic (PLC, FPGA, ASIC) devices are hybrids - hardware devices that are designed and programmed like software. As such, they fall in an assurance gray area. Programmable Logic is usually tested and verified as hardware, and the software aspects are ignored, potentially leading to safety or mission success concerns. The objective of this proposal is to first determine where and how Programmable Logic (PL) is used within NASA and document the current methods of assurance. Once that is known, raise awareness of the PL software aspects within the NASA engineering community and provide guidance for the use and assurance of PL form a software perspective.

Test results of a 20 kA high temperature superconductor current lead using REBCO tapes

NASA Astrophysics Data System (ADS)

Heller, R.; Fietz, W. H.; Gröner, F.; Heiduk, M.; Hollik, M.; Lange, C.; Lietzow, R.

2018-05-01

The Karlsruhe Institute of Technology has developed a 20 kA high temperature superconductor (HTS) current lead (CL) using the second generation material REBCO, as industry worldwide concentrate on the production of this material. The aim was to demonstrate the possibility of replacing the Bi-2223/AgAu tapes by REBCO tapes, while for easy comparison of results, all other components are copies of the 20 kA HTS CL manufactured for the satellite tokamak JT-60SA. After the manufacture of all CL components including the newly developed REBCO module, the assembly of the CL has been executed at KIT and an experiment has been carried out in the CuLTKa test facility where the REBCO CL was installed and connected to a JT-60SA CL via a superconducting bus bar. The experiment covers steady state operation up to 20 kA, pulsed operation, measurement of the heat load at 4.5 K end, loss-of-flow-accident simulations, and quench performance studies. Here the results of these tests are reported and directly compared to those of the JT-60SA CL.

Near net shape processing of continuous lengths of superconducting wire

DOEpatents

Danyluk, Steven; McNallan, Michael; Troendly, Robert; Poeppel, Roger; Goretta, Kenneth; Lanagan, Michael

1997-01-01

A system and method for mechanically forming a ceramic superconductor product. A system for making the ceramic superconductor includes a metallic channel portion having a cross section for receiving a ceramic superconductor powder, a roll to mechanically reduce the channel cross section and included superconductor powder and a cap portion welded to the channel portion using a localized high energy source. The assembled bar is then mechanically reduced to form a tape or wire end product.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, S. A.; Plummer, G.; Fedor, J.

Mapping the distribution of currents inside a superconductor is usually performed indirectly through imaging of the stray magnetic fields above the surface. Here, we show that by direct imaging of the Doppler shift contribution to the quasiparticle excitation spectrum in the superconductor using low temperature scanning tunneling microscopy, we obtain directly the distribution of supercurrents inside the superconductor. We demonstrate the technique at the example of superconductor/ferromagnet hybrid structure that produces intricate current pattern consisting of combination Meissner shielding currents and Abrikosov vortex currents.

Testing of machine wound second generation HTS tape Vacuum Pressure Impregnated coils

NASA Astrophysics Data System (ADS)

Swaffield, D.; Lewis, C.; Eugene, J.; Ingles, M.; Peach, D.

2014-05-01

Delamination of second generation (2G) High Temperature Superconducting (HTS) tapes has previously been reported when using resin based insulation systems for wound coils. One proposed root cause is the differential thermal contraction between the coil former and the resin encapsulated coil turns resulting in the tape c-axis tensile stress being exceeded. Importantly, delamination results in unacceptable degradation of the superconductor critical current level. To mitigate the delamination risk and prove winding, jointing and Vacuum Pressure Impregnation (VPI) processes in the production of coils for superconducting rotating machines at GE Power Conversion two scaled trial coils have been wound and extensively tested. The coils are wound from 12mm wide 2G HTS tape supplied by AMSC onto stainless steel 'racetrack' coil formers. The coils are wound in two layers which include both in-line and layer-layer joints subject to in-process test. The resin insulation system chosen is VPI and oven cured. Tests included; insulation resistance, repeat quench and recovery of the superconductor, heat runs and measurement of n-value, before and after multiple thermal cycling between ambient and 35 Kelvin. No degradation of coil performance is evidenced.

Broad-Based Search for New and Practical Superconductors

DTIC Science & Technology

2014-10-31

dielectric metamaterial has been tested in experiments with compressed mixtures of tin and barium titanate (BTO) and strontium titanate(STO) nanoparticles...work is published in Phys. Rev. B 89 , 134516 (2014). 3. New/Unexplored Directions: Search for Superconductivity in Naturally Occurring Mineral

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lombardo, v.; Barzi, E.; Turrioni, D.

Superconducting magnets with magnetic fields above 20 T will be needed for a Muon Collider and possible LHC energy upgrade. This field level exceeds the possibilities of traditional Low Temperature Superconductors (LTS) such as Nb{sub 3}Sn and Nb{sub 3}Al. Presently the use of high field high temperature superconductors (HTS) is the only option available for achieving such field levels. Commercially available YBCO comes in tapes and shows noticeable anisotropy with respect to field orientation, which needs to be accounted for during magnet design. In the present work, critical current test results are presented for YBCO tape manufactured by Bruker. Shortmore » sample measurements results are presented up to 14 T, assessing the level of anisotropy as a function of field, field orientation and operating temperature.« less

Design of High Field Solenoids made of High Temperature Superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartalesi, Antonio; /Pisa U.

2010-12-01

This thesis starts from the analytical mechanical analysis of a superconducting solenoid, loaded by self generated Lorentz forces. Also, a finite element model is proposed and verified with the analytical results. To study the anisotropic behavior of a coil made by layers of superconductor and insulation, a finite element meso-mechanic model is proposed and designed. The resulting material properties are then used in the main solenoid analysis. In parallel, design work is performed as well: an existing Insert Test Facility (ITF) is adapted and structurally verified to support a coil made of YBa{sub 2}Cu{sub 3}O{sub 7}, a High Temperature Superconductormore » (HTS). Finally, a technological winding process was proposed and the required tooling is designed.« less

Measured losses in superconductor magnets for 60-Hertz ac operation.

NASA Technical Reports Server (NTRS)

Hamlet, I. L.; Kilgore, R. A.

1971-01-01

Results of an experimental study of electrical losses in superconductor magnets. Preliminary 60-Hz ac loss data are presented for coils constructed of Nb3Sn ribbon, Nb-Ti cable, and multifilament Nb-Ti. Losses have been measured for different size coils up to approximately 20 cm in diameter. Of the conductor types tested, Nb3Sn ribbon has the lowest losses for ac operation. In Nb3Sn-ribbon coils of different sizes, the loss per unit length of conductor is shown to decrease with a decrease in the rate of change of current and to increase, in general, with increase in coil size. An important aspect of the study is the high degree of repeatability of the data.

Program Monitoring with LTL in EAGLE

NASA Technical Reports Server (NTRS)

Barringer, Howard; Goldberg, Allen; Havelund, Klaus; Sen, Koushik

2004-01-01

We briefly present a rule-based framework called EAGLE, shown to be capable of defining and implementing finite trace monitoring logics, including future and past time temporal logic, extended regular expressions, real-time and metric temporal logics (MTL), interval logics, forms of quantified temporal logics, and so on. In this paper we focus on a linear temporal logic (LTL) specialization of EAGLE. For an initial formula of size m, we establish upper bounds of O(m(sup 2)2(sup m)log m) and O(m(sup 4)2(sup 2m)log(sup 2) m) for the space and time complexity, respectively, of single step evaluation over an input trace. This bound is close to the lower bound O(2(sup square root m) for future-time LTL presented. EAGLE has been successfully used, in both LTL and metric LTL forms, to test a real-time controller of an experimental NASA planetary rover.

Magnetic proximity effect at the interface between a cuprate superconductor and an oxide spin valve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ovsyannikov, G. A., E-mail: gena@hitech.cplire.ru; Demidov, V. V.; Khaydukov, Yu. N.

2016-04-15

A heterostructure that consists of the YBa{sub 2}Cu{sub 3}O{sub 7–δ} cuprate superconductor and the SrRuO{sub 3}/La{sub 0.7}Sr{sub 0.3}MnO{sub 3} ruthenate/manganite spin valve is investigated using SQUID magnetometry, ferromagnetic resonance, and neutron reflectometry. It is shown that a magnetic moment is induced due to the magnetic proximity effect in the superconducting part of the heterostructure, while the magnetic moment in the composite ferromagnetic interlayer is suppressed. The magnetization emerging in the superconductor coincides in order of magnitude with the results of calculations taking into account the induced magnetic moment of Cu atoms because of orbital reconstruction at the interface between themore » superconductor and the ferromagnet, as well as with the results of the model taking into account the variations in the density of states at a distance on the order of the coherence length in the superconductor. The experimentally obtained characteristic penetration depth of the magnetic moment in the superconductor considerably exceeds the coherence length of the cuprate superconductor, which indicates the predominance of the mechanism of induced magnetic moment of Cu atoms.« less

Near net shape processing of continuous lengths of superconducting wire

DOEpatents

Danyluk, S.; McNallan, M.; Troendly, R.; Poeppel, R.; Goretta, K.; Lanagan, M.

1997-08-26

A system and method for mechanically forming a ceramic superconductor product are disclosed. A system for making the ceramic superconductor includes a metallic channel portion having a cross section for receiving a ceramic superconductor powder, a roll to mechanically reduce the channel cross section and included superconductor powder and a cap portion welded to the channel portion using a localized high energy source. The assembled bar is then mechanically reduced to form a tape or wire end product. 9 figs.

Study of the glass formation of high temperature superconductors

NASA Technical Reports Server (NTRS)

Ethridge, Edwin C.; Kaukler, William F.; Rolin, Terry

1992-01-01

A number of compositions of ceramic oxide high T(sub c) superconductors were elevated for their glass formation ability by means of rapid thermal analysis during quenching, optical, and electron microscopy of the quenched samples, and with subsequent DSC measurements. Correlations between experimental measurements and the methodical composition changes identified the formulations of superconductors that can easily form glass. The superconducting material was first formed as a glass; then, with subsequent devitrification, it was formed into a bulk crystalline superconductor by a series of processing methods.

Superconductor in a weak static gravitational field

NASA Astrophysics Data System (ADS)

Ummarino, Giovanni Alberto; Gallerati, Antonio

2017-08-01

We provide the detailed calculation of a general form for Maxwell and London equations that takes into account gravitational corrections in linear approximation. We determine the possible alteration of a static gravitational field in a superconductor making use of the time-dependent Ginzburg-Landau equations, providing also an analytic solution in the weak field condition. Finally, we compare the behavior of a high-T_ {c} superconductor with a classical low-T_ {c} superconductor, analyzing the values of the parameters that can enhance the reduction of the gravitational field.

Status of high temperature superconductor cable and fault current limiter projects at American Superconductor

NASA Astrophysics Data System (ADS)

Maguire, J. F.; Yuan, J.

2009-10-01

This paper will describe the status of three key programs currently underway at American Superconductor Corp. The first program is the LIPA project which is a transmission voltage high temperature superconducting cable program, with funding support from the US Department of Energy. The 600 m cable, capable of carrying 574 MVA, was successfully installed and commissioned in LIPA grid on April 22, 2008. An overview of the project, system level design details and operational data will be provided. In addition, the status of the newly awarded LIPA II project will be described. The second program is Project Hydra, with funding support from the US Department of Homeland Security, to design, develop and demonstrate an HTS cable with fault current limiting functionality. The cable is 300 m long and is being designed to carry 96 MVA at a distribution level voltage of 13.8 kV. The cable will be permanently installed and energized in Manhattan, New York in 2010. The initial status of Project Hydra will be presented. The final program to be discussed is a transmission voltage, high temperature superconducting fault current limiter funded by the US DOE. The project encompasses the design, construction and test of a 115 kV FCL for power transmission within a time frame of 4-5 years. Installation and testing are planned for a Southern California Edison substation. A project overview and progress under the first phase will be reported.

An Adaptive Fuzzy-Logic Traffic Control System in Conditions of Saturated Transport Stream

PubMed Central

Marakhimov, A. R.; Igamberdiev, H. Z.; Umarov, Sh. X.

2016-01-01

This paper considers the problem of building adaptive fuzzy-logic traffic control systems (AFLTCS) to deal with information fuzziness and uncertainty in case of heavy traffic streams. Methods of formal description of traffic control on the crossroads based on fuzzy sets and fuzzy logic are proposed. This paper also provides efficient algorithms for implementing AFLTCS and develops the appropriate simulation models to test the efficiency of suggested approach. PMID:27517081

Electron refrigeration in hybrid structures with spin-split superconductors

NASA Astrophysics Data System (ADS)

Rouco, M.; Heikkilä, T. T.; Bergeret, F. S.

2018-01-01

Electron tunneling between superconductors and normal metals has been used for an efficient refrigeration of electrons in the latter. Such cooling is a nonlinear effect and usually requires a large voltage. Here we study the electron cooling in heterostructures based on superconductors with a spin-splitting field coupled to normal metals via spin-filtering barriers. The cooling power shows a linear term in the applied voltage. This improves the coefficient of performance of electron refrigeration in the normal metal by shifting its optimum cooling to lower voltage, and also allows for cooling the spin-split superconductor by reverting the sign of the voltage. We also show how tunnel coupling spin-split superconductors with regular ones allows for a highly efficient refrigeration of the latter.

Low-Level Space Optimization of an AES Implementation for a Bit-Serial Fully Pipelined Architecture

NASA Astrophysics Data System (ADS)

Weber, Raphael; Rettberg, Achim

A previously developed AES (Advanced Encryption Standard) implementation is optimized and described in this paper. The special architecture for which this implementation is targeted comprises synchronous and systematic bit-serial processing without a central controlling instance. In order to shrink the design in terms of logic utilization we deeply analyzed the architecture and the AES implementation to identify the most costly logic elements. We propose to merge certain parts of the logic to achieve better area efficiency. The approach was integrated into an existing synthesis tool which we used to produce synthesizable VHDL code. For testing purposes, we simulated the generated VHDL code and ran tests on an FPGA board.

Aluminum and gold deposition on cleaved single crystals of Bi2CaSr2Cu2O8 superconductor

NASA Astrophysics Data System (ADS)

Wells, B. O.; Lindberg, P. A. P.; Shen, Z.-X.; Dessau, D. S.; Lindau, I.; Spicer, W. E.; Mitzi, D. B.; Kapitulnik, A.

1989-02-01

We have used photoelectron spectroscopy to study the changes in the electronic structure of cleaved, single crystal Bi2CaSr2Cu2O8 caused by deposition of aluminum and gold. Al reacts strongly with the superconductor surface. Even the lowest coverages of Al reduces the valency of Cu in the superconductor, draws oxygen out of the bulk, and strongly modifies the electronic states in the valence band. The Au shows little reaction with the superconductor surface. Underneath Au, the Cu valency is unchanged and the core peaks show no chemically shifted components. Au appears to passivate the surface of the superconductor and thus may aid in the processing of the Bi-Ca-Sr-Cu-O material. These results are consistent with earlier studies of Al and Au interfaces with other, polycrystalline oxide superconductors. Comparing with our own previous results, we conclude that Au is superior to Ag in passivating the Bi-Ca-Sr-Cu-O surface.

The color of polarization in cuprate superconductors

NASA Technical Reports Server (NTRS)

Hoff, H. A.; Osofsky, M. S.; Lechter, W. L.; Pande, C. S.

1991-01-01

A technique for the identification of individual anisotropic grains in a heterogeneous and opaque material involves the observation of grain color in reflected light through crossed polarizers (color of polarization). Such colors are generally characteristic of particular phases. When grains of many members of the class of hole carrier cuprate superconductors are so viewed at room temperature with a 'daylight' source, a characteristic color of polarization is observed. This color was studied in many of these cuprate superconductors and a strong correlation was found between color and the existence of superconductivity. Two members were also examined of the electron cuprate superconductors and it was found that they possess the same color of polarization as the hole carrier cuprate superconductors so far examined. The commonality of the characteristic color regardless of charge carrier indicates that the presence of this color is independent of carrier type. The correlation of this color with the existence of superconductivity in the cuprate superconductors suggests that the origin of the color relates to the origin of superconductivity. Photometric techniques are also discussed.

Disappearance of nodal gap across the insulator-superconductor transition in a copper-oxide superconductor.

PubMed

Peng, Yingying; Meng, Jianqiao; Mou, Daixiang; He, Junfeng; Zhao, Lin; Wu, Yue; Liu, Guodong; Dong, Xiaoli; He, Shaolong; Zhang, Jun; Wang, Xiaoyang; Peng, Qinjun; Wang, Zhimin; Zhang, Shenjin; Yang, Feng; Chen, Chuangtian; Xu, Zuyan; Lee, T K; Zhou, X J

2013-01-01

The parent compound of the copper-oxide high-temperature superconductors is a Mott insulator. Superconductivity is realized by doping an appropriate amount of charge carriers. How a Mott insulator transforms into a superconductor is crucial in understanding the unusual physical properties of high-temperature superconductors and the superconductivity mechanism. Here we report high-resolution angle-resolved photoemission measurement on heavily underdoped Bi₂Sr₂-xLaxCuO(₆+δ) system. The electronic structure of the lightly doped samples exhibit a number of characteristics: existence of an energy gap along the nodal direction, d-wave-like anisotropic energy gap along the underlying Fermi surface, and coexistence of a coherence peak and a broad hump in the photoemission spectra. Our results reveal a clear insulator-superconductor transition at a critical doping level of ~0.10 where the nodal energy gap approaches zero, the three-dimensional antiferromagnetic order disappears, and superconductivity starts to emerge. These observations clearly signal a close connection between the nodal gap, antiferromagnetism and superconductivity.

Thermal mechanisms responsible for the irreversible degradation of superconductivity in commercial superconductors

NASA Astrophysics Data System (ADS)

Romanovskii, V. R.

2017-08-01

Conditions for the irreversible propagation of thermal instabilities in commercial superconductors subjected to intense and soft cooling have been formulated. An analysis has been conducted using two types of the superconductor's I-V characteristics, i.e., an ideal I-V characteristic, which assumes a step superconducting-to-normal transition, and a continuous I-V characteristic, which is described by a power law. The propagation rate of thermal instabilities along the superconducting composite has been determined. Calculations have been made for both subcritical and supercritical values of the current. It has been shown that they propagate along a commercial superconductor in the form of a switching wave. In rapidly cooled commercial superconductors, the steady-state rate of thermal instability propagation in the longitudinal direction can only be positive because there is no region of steady stabilization. It has been proved that, in the case of thermal instability irreversible propagation, the rise in the commercial superconductor temperature is similar to diffusion processes that occur in explosive chain reactions.

Magnetically leviated superconducting bearing

DOEpatents

Weinberger, Bernard R.; Lynds, Jr., Lahmer

1993-01-01

A magnetically levitated superconducting bearing includes a magnet (2) mounted on a shaft (12) that is rotatable around an axis of rotation and a Type II superconductor (6) supported on a stator (14) in proximity to the magnet (2). The superconductor (6) is positioned so that when it is cooled to its superconducting state in the presence of a magnetic field, it interacts with the magnet (2) to produce an attractive force that levitates the magnet (2) and supports a load on the shaft (12). The interaction between the superconductor (6) and magnet(2) also produces surface screening currents (8) that generate a repulsive force perpendicular to the load. The bearing also has means for maintaining the superconductor at a temperature below its critical temperature (16, 18). The bearing could also be constructed so the magnet (2) is supported on the stator (14) and the superconductor (6) is mounted on the shaft (12). The bearing can be operated by cooling the superconductor (6) to its superconducting state in the presence of a magnetic field.

Superconducting power transmission system development. Cable insulation development

NASA Astrophysics Data System (ADS)

1983-09-01

The development of an underground superconducting power transmission system which is economical and technically attractive to the utility industry is discussed. Suitable superconductors and dielectric insulation were developed. Cables several hundred feet long are tested under realistic conditions. Three operating runs of about 2 weeks duration each were accomplished. The 60 Hz steady state performance of the cables under rated conditions was explored. Over voltage endurance tests and emergency level current tests were performed.

Failure Control Techniques for the SSME

NASA Technical Reports Server (NTRS)

Taniguchi, M. H.

1987-01-01

Since ground testing of the Space Shuttle Main Engine (SSME) began in 1975, the detection of engine anomalies and the prevention of major damage have been achieved by a multi-faceted detection/shutdown system. The system continues the monitoring task today and consists of the following: sensors, automatic redline and other limit logic, redundant sensors and controller voting logic, conditional decision logic, and human monitoring. Typically, on the order of 300 to 500 measurements are sensed and recorded for each test, while on the order of 100 are used for control and monitoring. Despite extensive monitoring by the current detection system, twenty-seven (27) major incidents have occurred. This number would appear insignificant compared with over 1200 hot-fire tests which have taken place since 1976. However, the number suggests the requirement for and future benefits of a more advanced failure detection system.

A fault injection experiment using the AIRLAB Diagnostic Emulation Facility

NASA Technical Reports Server (NTRS)

Baker, Robert; Mangum, Scott; Scheper, Charlotte

1988-01-01

The preparation for, conduct of, and results of a simulation based fault injection experiment conducted using the AIRLAB Diagnostic Emulation facilities is described. An objective of this experiment was to determine the effectiveness of the diagnostic self-test sequences used to uncover latent faults in a logic network providing the key fault tolerance features for a flight control computer. Another objective was to develop methods, tools, and techniques for conducting the experiment. More than 1600 faults were injected into a logic gate level model of the Data Communicator/Interstage (C/I). For each fault injected, diagnostic self-test sequences consisting of over 300 test vectors were supplied to the C/I model as inputs. For each test vector within a test sequence, the outputs from the C/I model were compared to the outputs of a fault free C/I. If the outputs differed, the fault was considered detectable for the given test vector. These results were then analyzed to determine the effectiveness of some test sequences. The results established coverage of selt-test diagnostics, identified areas in the C/I logic where the tests did not locate faults, and suggest fault latency reduction opportunities.

Method of preforming and assembling superconducting circuit elements

NASA Astrophysics Data System (ADS)

Haertling, Gene H.; Buckley, John D.

1991-03-01

The invention is a method of preforming and pretesting rigid and discrete superconductor circuit elements to optimize the superconductivity development of the preformed circuit element prior to its assembly, and encapsulation on a substrate and final environmental testing of the assembled ceramic superconductive elements.

A model for the compositions of non-stoichiometric intermediate phases formed by diffusion reactions, and its application to Nb 3Sn superconductors

DOE PAGES

Xu, X.; Sumption, M. D.

2016-01-12

In this work we explore the compositions of non-stoichiometric intermediate phases formed by diffusion reactions: a mathematical framework is developed and tested against the specific case of Nb 3Sn superconductors. In the first part, the governing equations for the bulk diffusion and interphase interface reactions during the growth of a compound are derived, numerical solutions to which give both the composition profile and growth rate of the compound layer. The analytic solutions are obtained with certain approximations made. In the second part, we explain an effect that the composition characteristics of compounds can be quite different depending on whether itmore » is the bulk diffusion or grain boundary diffusion that dominates in the compounds, and that “frozen” bulk diffusion leads to unique composition characteristics that the bulk composition of a compound layer remains unchanged after its initial formation instead of varying with the diffusion reaction system; here the model is modified for the case of grain boundary diffusion. Lastly, we apply this model to the Nb 3Sn superconductors and propose approaches to control their compositions.« less

Memristor-CMOS hybrid integrated circuits for reconfigurable logic.

PubMed

Xia, Qiangfei; Robinett, Warren; Cumbie, Michael W; Banerjee, Neel; Cardinali, Thomas J; Yang, J Joshua; Wu, Wei; Li, Xuema; Tong, William M; Strukov, Dmitri B; Snider, Gregory S; Medeiros-Ribeiro, Gilberto; Williams, R Stanley

2009-10-01

Hybrid reconfigurable logic circuits were fabricated by integrating memristor-based crossbars onto a foundry-built CMOS (complementary metal-oxide-semiconductor) platform using nanoimprint lithography, as well as materials and processes that were compatible with the CMOS. Titanium dioxide thin-film memristors served as the configuration bits and switches in a data routing network and were connected to gate-level CMOS components that acted as logic elements, in a manner similar to a field programmable gate array. We analyzed the chips using a purpose-built testing system, and demonstrated the ability to configure individual devices, use them to wire up various logic gates and a flip-flop, and then reconfigure devices.

Notes on stochastic (bio)-logic gates: computing with allosteric cooperativity

PubMed Central

Agliari, Elena; Altavilla, Matteo; Barra, Adriano; Dello Schiavo, Lorenzo; Katz, Evgeny

2015-01-01

Recent experimental breakthroughs have finally allowed to implement in-vitro reaction kinetics (the so called enzyme based logic) which code for two-inputs logic gates and mimic the stochastic AND (and NAND) as well as the stochastic OR (and NOR). This accomplishment, together with the already-known single-input gates (performing as YES and NOT), provides a logic base and paves the way to the development of powerful biotechnological devices. However, as biochemical systems are always affected by the presence of noise (e.g. thermal), standard logic is not the correct theoretical reference framework, rather we show that statistical mechanics can work for this scope: here we formulate a complete statistical mechanical description of the Monod-Wyman-Changeaux allosteric model for both single and double ligand systems, with the purpose of exploring their practical capabilities to express noisy logical operators and/or perform stochastic logical operations. Mixing statistical mechanics with logics, and testing quantitatively the resulting findings on the available biochemical data, we successfully revise the concept of cooperativity (and anti-cooperativity) for allosteric systems, with particular emphasis on its computational capabilities, the related ranges and scaling of the involved parameters and its differences with classical cooperativity (and anti-cooperativity). PMID:25976626

Notes on stochastic (bio)-logic gates: computing with allosteric cooperativity.

PubMed

Agliari, Elena; Altavilla, Matteo; Barra, Adriano; Dello Schiavo, Lorenzo; Katz, Evgeny

2015-05-15

Recent experimental breakthroughs have finally allowed to implement in-vitro reaction kinetics (the so called enzyme based logic) which code for two-inputs logic gates and mimic the stochastic AND (and NAND) as well as the stochastic OR (and NOR). This accomplishment, together with the already-known single-input gates (performing as YES and NOT), provides a logic base and paves the way to the development of powerful biotechnological devices. However, as biochemical systems are always affected by the presence of noise (e.g. thermal), standard logic is not the correct theoretical reference framework, rather we show that statistical mechanics can work for this scope: here we formulate a complete statistical mechanical description of the Monod-Wyman-Changeaux allosteric model for both single and double ligand systems, with the purpose of exploring their practical capabilities to express noisy logical operators and/or perform stochastic logical operations. Mixing statistical mechanics with logics, and testing quantitatively the resulting findings on the available biochemical data, we successfully revise the concept of cooperativity (and anti-cooperativity) for allosteric systems, with particular emphasis on its computational capabilities, the related ranges and scaling of the involved parameters and its differences with classical cooperativity (and anti-cooperativity).

Notes on stochastic (bio)-logic gates: computing with allosteric cooperativity

NASA Astrophysics Data System (ADS)

Agliari, Elena; Altavilla, Matteo; Barra, Adriano; Dello Schiavo, Lorenzo; Katz, Evgeny

2015-05-01

Recent experimental breakthroughs have finally allowed to implement in-vitro reaction kinetics (the so called enzyme based logic) which code for two-inputs logic gates and mimic the stochastic AND (and NAND) as well as the stochastic OR (and NOR). This accomplishment, together with the already-known single-input gates (performing as YES and NOT), provides a logic base and paves the way to the development of powerful biotechnological devices. However, as biochemical systems are always affected by the presence of noise (e.g. thermal), standard logic is not the correct theoretical reference framework, rather we show that statistical mechanics can work for this scope: here we formulate a complete statistical mechanical description of the Monod-Wyman-Changeaux allosteric model for both single and double ligand systems, with the purpose of exploring their practical capabilities to express noisy logical operators and/or perform stochastic logical operations. Mixing statistical mechanics with logics, and testing quantitatively the resulting findings on the available biochemical data, we successfully revise the concept of cooperativity (and anti-cooperativity) for allosteric systems, with particular emphasis on its computational capabilities, the related ranges and scaling of the involved parameters and its differences with classical cooperativity (and anti-cooperativity).

Radiation evaluation study of LSI RAM technologies

NASA Astrophysics Data System (ADS)

Dinger, G. L.; Knoll, M. G.

1980-01-01

Five commercial LSI static random access memory technologies having a 1 kilobit capacity were radiation characterized. Arrays from the transistor-transistor-logic (TTL), Schottky TTL, n-channel metal oxide semiconductor, complementary metal oxide semiconductor (CMOS), and CMOS/silicon on sapphire families were evaluated. Radiation failure thresholds for gamma doserate logic upset, total gamma dose survivability, and neutron fluence survivability were determined. A brief analysis of the radiation failure mechanism for each of the logic families tested is included.

Steering of an automated vehicle in an unstructured environment

NASA Astrophysics Data System (ADS)

Kanakaraju, Sampath; Shanmugasundaram, Sathish K.; Thyagarajan, Ramesh; Hall, Ernest L.

1999-08-01

The purpose of this paper is to describe a high-level path planning logic, which processes the data from a vision system and an ultrasonic obstacle avoidance system and steers an autonomous mobile robot between obstacles. The test bed was an autonomous root built at University of Cincinnati, and this logic was tested and debugged on this machine. Attempts have already been made to incorporate fuzzy system on a similar robot, and this paper extends them to take advantage of the robot's ZTR capability. Using the integrated vision syste, the vehicle senses its location and orientation. A rotating ultrasonic sensor is used to map the location and size of possible obstacles. With these inputs the fuzzy logic controls the speed and the steering decisions of the robot. With the incorporation of this logic, it has been observed that Bearcat II has been very successful in avoiding obstacles very well. This was achieved in the Ground Robotics Competition conducted by the AUVS in June 1999, where it travelled a distance of 154 feet in a 10ft. wide path ridden with obstacles. This logic proved to be a significant contributing factor in this feat of Bearcat II.

Concealed d -wave pairs in the s ± condensate of iron-based superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ong, Tzen; Coleman, Piers; Schmalian, Jörg

A central question in iron-based superconductivity is the mechanism by which the paired electrons minimize their strong mutual Coulomb repulsion. In most unconventional superconductors, Coulomb repulsion is minimized through the formation of higher angular momentum Cooper pairs, with Fermi surface nodes in the pair wavefunction. The apparent absence of such nodes in the iron-based superconductors has led to a belief they form an s-wave (s ±) singlet state, which changes sign between the electron and hole pockets. However, the multiorbital nature of these systems opens an alternative possibility. In this paper, we propose a new class of s ± statemore » containing a condensate of d-wave Cooper pairs, concealed by their entanglement with the iron orbitals. By combining the d-wave (L=2) motion of the pairs with the internal angular momenta I =2 of the iron orbitals to make a singlet (J =L+I =0), an s ± superconductor with a nontrivial topology is formed. This scenario allows us to understand the development of octet nodes in potassium-doped Ba 1$-$xK XFe 2As 2 as a reconfiguration of the orbital and internal angular momentum into a high spin (J =L+I =4) state; the reverse transition under pressure into a fully gapped state can then be interpreted as a return to the low-spin singlet. Finally, the formation of orbitally entangled pairs is predicted to give rise to a shift in the orbital content at the Fermi surface, which can be tested via laser-based angle-resolved photoemission spectroscopy.« less

Concealed d -wave pairs in the s ± condensate of iron-based superconductors

DOE PAGES

Ong, Tzen; Coleman, Piers; Schmalian, Jörg

2016-05-02

A central question in iron-based superconductivity is the mechanism by which the paired electrons minimize their strong mutual Coulomb repulsion. In most unconventional superconductors, Coulomb repulsion is minimized through the formation of higher angular momentum Cooper pairs, with Fermi surface nodes in the pair wavefunction. The apparent absence of such nodes in the iron-based superconductors has led to a belief they form an s-wave (s ±) singlet state, which changes sign between the electron and hole pockets. However, the multiorbital nature of these systems opens an alternative possibility. In this paper, we propose a new class of s ± statemore » containing a condensate of d-wave Cooper pairs, concealed by their entanglement with the iron orbitals. By combining the d-wave (L=2) motion of the pairs with the internal angular momenta I =2 of the iron orbitals to make a singlet (J =L+I =0), an s ± superconductor with a nontrivial topology is formed. This scenario allows us to understand the development of octet nodes in potassium-doped Ba 1$-$xK XFe 2As 2 as a reconfiguration of the orbital and internal angular momentum into a high spin (J =L+I =4) state; the reverse transition under pressure into a fully gapped state can then be interpreted as a return to the low-spin singlet. Finally, the formation of orbitally entangled pairs is predicted to give rise to a shift in the orbital content at the Fermi surface, which can be tested via laser-based angle-resolved photoemission spectroscopy.« less

Concealed d-wave pairs in the s± condensate of iron-based superconductors.

PubMed

Ong, Tzen; Coleman, Piers; Schmalian, Jörg

2016-05-17

A central question in iron-based superconductivity is the mechanism by which the paired electrons minimize their strong mutual Coulomb repulsion. In most unconventional superconductors, Coulomb repulsion is minimized through the formation of higher angular momentum Cooper pairs, with Fermi surface nodes in the pair wavefunction. The apparent absence of such nodes in the iron-based superconductors has led to a belief they form an s-wave ([Formula: see text]) singlet state, which changes sign between the electron and hole pockets. However, the multiorbital nature of these systems opens an alternative possibility. Here, we propose a new class of [Formula: see text] state containing a condensate of d-wave Cooper pairs, concealed by their entanglement with the iron orbitals. By combining the d-wave ([Formula: see text]) motion of the pairs with the internal angular momenta [Formula: see text] of the iron orbitals to make a singlet ([Formula: see text]), an [Formula: see text] superconductor with a nontrivial topology is formed. This scenario allows us to understand the development of octet nodes in potassium-doped Ba1-x KXFe2As2 as a reconfiguration of the orbital and internal angular momentum into a high spin ([Formula: see text]) state; the reverse transition under pressure into a fully gapped state can then be interpreted as a return to the low-spin singlet. The formation of orbitally entangled pairs is predicted to give rise to a shift in the orbital content at the Fermi surface, which can be tested via laser-based angle-resolved photoemission spectroscopy.

High-Tc SNS Junctions: A New Generation of Proximity-Coupled Josephson Devices

NASA Technical Reports Server (NTRS)

Kleinsasser, A. W.

1997-01-01

This paper reviews this evolution of proximity - coupled Josephson jucntion from the early investigations on low temperature superconductor-normal -superconductor junctions through the introduction of hybrid superconductor-semiconductor devices and the resulting interest in mesoscopic Josephson junctions, to the recent development of high temperature devices.

High temperature superconductors: A technological revolution

NASA Technical Reports Server (NTRS)

1990-01-01

The objectives are to demonstrate the Meissner effect through magnetic levitation, to demonstrate one application of the Meissner effect, the low friction magnetic rotation bearing, and to demonstrate magnetic flux penetration and the Type II nature of ceramic superconductors via the stacking of the superconductor disks. Experimental equipment and procedures are described.

Superconducting matrix fault current limiter with current-driven trigger mechanism

DOEpatents

Yuan; Xing

2008-04-15

A modular and scalable Matrix-type Fault Current Limiter (MFCL) that functions as a "variable impedance" device in an electric power network, using components made of superconducting and non-superconducting electrically conductive materials. An inductor is connected in series with the trigger superconductor in the trigger matrix and physically surrounds the superconductor. The current surge during a fault will generate a trigger magnetic field in the series inductor to cause fast and uniform quenching of the trigger superconductor to significantly reduce burnout risk due to superconductor material non-uniformity.

Automatic HTS force measurement instrument

DOEpatents

Sanders, Scott T.; Niemann, Ralph C.

1999-01-01

A device for measuring the levitation force of a high temperature superconductor sample with respect to a reference magnet includes a receptacle for holding several high temperature superconductor samples each cooled to superconducting temperature. A rotatable carousel successively locates a selected one of the high temperature superconductor samples in registry with the reference magnet. Mechanism varies the distance between one of the high temperature superconductor samples and the reference magnet, and a sensor measures levitation force of the sample as a function of the distance between the reference magnet and the sample. A method is also disclosed.

Synthesis of highly phase pure BSCCO superconductors

DOEpatents

Dorris, S.E.; Poeppel, R.B.; Prorok, B.C.; Lanagan, M.T.; Maroni, V.A.

1995-11-21

An article and method of manufacture (Bi, Pb)-Sr-Ca-Cu-O superconductor are disclosed. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor. 5 figs.

Glass formability of high T(sub c) Bi-Sr-Ca-Cu-O superconductors

NASA Technical Reports Server (NTRS)

Kaukler, William F.

1992-01-01

A number of compositions of ceramic oxide high T(sub c) superconductors were evaluated for their glass formation ability by means of rapid thermal analysis during quenching, optical and electron microscopy of the quenched samples, and with subsequent DSC measurements. Correlations between experimental measurements and the methodical composition changes identified the formulations of superconductors that can easily form glass. The superconducting material was first formed as a glass, then with subsequent devitrification it was formed into bulk crystalline superconductor by a series of processing methods.

Synthesis of highly phase pure BSCCO superconductors

DOEpatents

Dorris, Stephen E.; Poeppel, Roger B.; Prorok, Barton C.; Lanagan, Michael T.; Maroni, Victor A.

1995-01-01

An article and method of manufacture of (Bi, Pb)-Sr-Ca-Cu-O superconductor. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor.

Synthesis of highly phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor

DOEpatents

Dorris, Stephen E.; Poeppel, Roger B.; Prorok, Barton C.; Lanagan, Michael T.; Maroni, Victor A.

1994-01-01

An article and method of manufacture of (Bi,Pb)-Sr-Ca-Cu-O superconductor. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi,Pb)-Sr-Ca-Cu-O superconductor.

Fabrication Of High-Tc Superconducting Integrated Circuits

NASA Technical Reports Server (NTRS)

Bhasin, Kul B.; Warner, Joseph D.

1992-01-01

Microwave ring resonator fabricated to demonstrate process for fabrication of passive integrated circuits containing high-transition-temperature superconductors. Superconductors increase efficiencies of communication systems, particularly microwave communication systems, by reducing ohmic losses and dispersion of signals. Used to reduce sizes and masses and increase aiming accuracies and tracking speeds of millimeter-wavelength, electronically steerable antennas. High-Tc superconductors preferable for such applications because they operate at higher temperatures than low-Tc superconductors do, therefore, refrigeration systems needed to maintain superconductivity designed smaller and lighter and to consume less power.

Cloaking magnetic field and generating electric field with topological insulator and superconductor bi-layer sphere

NASA Astrophysics Data System (ADS)

Xu, Jin

2017-12-01

When an electric field is applied on a topological insulator, not only the electric field is generated, but also the magnetic field is generated, vice versa. I designed topological insulator and superconductor bi-layer magnetic cloak, derived the electric field and magnetic field inside and outside the topological insulator and superconductor sphere. Simulation and calculation results show that the applied magnetic field is screened by the topological insulator and superconductor bi-layer, and the electric field is generated in the cloaked region.

Quasiparticle entropy in superconductor/normal metal/superconductor proximity junctions in the diffusive limit

NASA Astrophysics Data System (ADS)

Virtanen, P.; Vischi, F.; Strambini, E.; Carrega, M.; Giazotto, F.

2017-12-01

We discuss the quasiparticle entropy and heat capacity of a dirty superconductor/normal metal/superconductor junction. In the case of short junctions, the inverse proximity effect extending in the superconducting banks plays a crucial role in determining the thermodynamic quantities. In this case, commonly used approximations can violate thermodynamic relations between supercurrent and quasiparticle entropy. We provide analytical and numerical results as a function of different geometrical parameters. Quantitative estimates for the heat capacity can be relevant for the design of caloritronic devices or radiation sensor applications.

Symmetry conditions of a nodal superconductor for generating robust flat-band Andreev bound states at its dirty surface

NASA Astrophysics Data System (ADS)

Ikegaya, Satoshi; Kobayashi, Shingo; Asano, Yasuhiro

2018-05-01

We discuss the symmetry property of a nodal superconductor that hosts robust flat-band zero-energy states at its surface under potential disorder. Such robust zero-energy states are known to induce the anomalous proximity effect in a dirty normal metal attached to a superconductor. A recent study has shown that a topological index NZES describes the number of zero-energy states at the dirty surface of a p -wave superconductor. We generalize the theory to clarify the conditions required for a superconductor that enables NZES≠0 . Our results show that NZES≠0 is realized in a topological material that belongs to either the BDI or CII class. We also present two realistic Hamiltonians that result in NZES≠0 .

Electromagnetic properties of impure superconductors with pair-breaking processes

NASA Astrophysics Data System (ADS)

Herman, František; Hlubina, Richard

2017-07-01

Recently, a generic model was proposed for the single-particle properties of gapless superconductors with simultaneously present pair-conserving and pair-breaking impurity scatterings (the so-called Dynes superconductors). Here we calculate the optical conductivity of the Dynes superconductors. Our approach is applicable for all disorder strengths from the clean limit up to the dirty limit and for all relative ratios of the two types of scattering; nevertheless, the complexity of our description is equivalent to that of the widely used Mattis-Bardeen theory. We identify two optical fingerprints of the Dynes superconductors: (i) the presence of two absorption edges and (ii) finite absorption at vanishing frequencies even at the lowest temperatures. We demonstrate that the recent anomalous optical data on thin MoN films can be reasonably fitted by our theory.

Fluorescence intensity positivity classification of Hep-2 cells images using fuzzy logic

NASA Astrophysics Data System (ADS)

Sazali, Dayang Farzana Abang; Janier, Josefina Barnachea; May, Zazilah Bt.

2014-10-01

Indirect Immunofluorescence (IIF) is a good standard used for antinuclear autoantibody (ANA) test using Hep-2 cells to determine specific diseases. Different classifier algorithm methods have been proposed in previous works however, there still no valid set as a standard to classify the fluorescence intensity. This paper presents the use of fuzzy logic to classify the fluorescence intensity and to determine the positivity of the Hep-2 cell serum samples. The fuzzy algorithm involves the image pre-processing by filtering the noises and smoothen the image, converting the red, green and blue (RGB) color space of images to luminosity layer, chromaticity layer "a" and "b" (LAB) color space where the mean value of the lightness and chromaticity layer "a" was extracted and classified by using fuzzy logic algorithm based on the standard score ranges of antinuclear autoantibody (ANA) fluorescence intensity. Using 100 data sets of positive and intermediate fluorescence intensity for testing the performance measurements, the fuzzy logic obtained an accuracy of intermediate and positive class as 85% and 87% respectively.

Nanoscale phase engineering of thermal transport with a Josephson heat modulator.

PubMed

Fornieri, Antonio; Blanc, Christophe; Bosisio, Riccardo; D'Ambrosio, Sophie; Giazotto, Francesco

2016-03-01

Macroscopic quantum phase coherence has one of its pivotal expressions in the Josephson effect, which manifests itself both in charge and energy transport. The ability to master the amount of heat transferred through two tunnel-coupled superconductors by tuning their phase difference is the core of coherent caloritronics, and is expected to be a key tool in a number of nanoscience fields, including solid-state cooling, thermal isolation, radiation detection, quantum information and thermal logic. Here, we show the realization of the first balanced Josephson heat modulator designed to offer full control at the nanoscale over the phase-coherent component of thermal currents. Our device provides magnetic-flux-dependent temperature modulations up to 40 mK in amplitude with a maximum of the flux-to-temperature transfer coefficient reaching 200 mK per flux quantum at a bath temperature of 25 mK. Foremost, it demonstrates the exact correspondence in the phase engineering of charge and heat currents, breaking ground for advanced caloritronic nanodevices such as thermal splitters, heat pumps and time-dependent electronic engines.

Nanoscale phase engineering of thermal transport with a Josephson heat modulator

NASA Astrophysics Data System (ADS)

Fornieri, Antonio; Blanc, Christophe; Bosisio, Riccardo; D'Ambrosio, Sophie; Giazotto, Francesco

2016-03-01

Macroscopic quantum phase coherence has one of its pivotal expressions in the Josephson effect, which manifests itself both in charge and energy transport. The ability to master the amount of heat transferred through two tunnel-coupled superconductors by tuning their phase difference is the core of coherent caloritronics, and is expected to be a key tool in a number of nanoscience fields, including solid-state cooling, thermal isolation, radiation detection, quantum information and thermal logic. Here, we show the realization of the first balanced Josephson heat modulator designed to offer full control at the nanoscale over the phase-coherent component of thermal currents. Our device provides magnetic-flux-dependent temperature modulations up to 40 mK in amplitude with a maximum of the flux-to-temperature transfer coefficient reaching 200 mK per flux quantum at a bath temperature of 25 mK. Foremost, it demonstrates the exact correspondence in the phase engineering of charge and heat currents, breaking ground for advanced caloritronic nanodevices such as thermal splitters, heat pumps and time-dependent electronic engines.

Frequency-tunable superconducting resonators via nonlinear kinetic inductance

NASA Astrophysics Data System (ADS)

Vissers, M. R.; Hubmayr, J.; Sandberg, M.; Chaudhuri, S.; Bockstiegel, C.; Gao, J.

2015-08-01

We have designed, fabricated, and tested a frequency-tunable high-Q superconducting resonator made from a niobium titanium nitride film. The frequency tunability is achieved by injecting a DC through a current-directing circuit into the nonlinear inductor whose kinetic inductance is current-dependent. We have demonstrated continuous tuning of the resonance frequency in a 180 MHz frequency range around 4.5 GHz while maintaining the high internal quality factor Qi > 180 000. This device may serve as a tunable filter and find applications in superconducting quantum computing and measurement. It also provides a useful tool to study the nonlinear response of a superconductor. In addition, it may be developed into techniques for measurement of the complex impedance of a superconductor at its transition temperature and for readout of transition-edge sensors.

Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor.

PubMed

von Rohr, Fabian; Winiarski, Michał J; Tao, Jing; Klimczuk, Tomasz; Cava, Robert Joseph

2016-11-15

High-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder. Here we show that the valence electron count dependence of the superconducting transition temperature in the high-entropy alloy falls between those of analogous simple solid solutions and amorphous materials and test the effect of alloy complexity on the superconductivity. We propose high-entropy alloys as excellent intermediate systems for studying superconductivity as it evolves between crystalline and amorphous materials.

Robust d -wave pairing symmetry in multiorbital cobalt high-temperature superconductors

NASA Astrophysics Data System (ADS)

Li, Yinxiang; Han, Xinloong; Qin, Shengshan; Le, Congcong; Wang, Qiang-Hua; Hu, Jiangping

2017-07-01

The pairing symmetry of the cobalt high-temperature (high-Tc) superconductors formed by vertex-shared cation-anion tetrahedral complexes is studied by the methods of mean-field, random phase approximation (RPA), and functional renormalization-group (FRG) analyses. The results of all of these methods show that the dx2-y2 pairing symmetry is robustly favored near half filling. The RPA and FRG methods, which are valid in weak-interaction regions, predict that the superconducting state is also strongly orbital selective, namely, the dx2-y2 orbital that has the largest density near half filling among the three t2 g orbitals dominates superconducting pairing. These results suggest that these materials, if synthesized, can provide an indisputable test of the high-Tc pairing mechanism and the validity of different theoretical methods.

Micromachined Millimeter- and Submillimeter-Wave SIS Heterodyne Receivers for Remote Sensing

NASA Technical Reports Server (NTRS)

Hu, Qing

1998-01-01

A heterodyne mixer with a micromachined horn antenna and a superconductor -insulator-superconductor (SIS) tunnel junction as mixing element is tested in the W-band (75-115 GHz) frequency range. Micromachined integrated horn antennas consist of a dipole antenna suspended on a thin Si3N4 dielectric membrane inside a pyramidal cavity etched in silicon. The mixer performance is optimized by using a backing plane behind the dipole antenna to tune out the capacitance of the tunnel junction. The lowest receiver noise temperature of 30+/-3 K without any correction) is measured at 106 GHz with a 3-dB bandwidth of 8 GHz. This sensitivity is comparable to the state-of-the-art waveguide and quasi-optical SIS receivers, showing the potential use of micromachined horn antennas in imaging arrays.

Programmable Logic Application Notes

NASA Technical Reports Server (NTRS)

Katz, Richard

1998-01-01

This column will be provided each quarter as a source for reliability, radiation results, NASA capabilities, and other information on programmable logic devices and related applications. This quarter's column will include some announcements and some recent radiation test results and evaluations of interest. Specifically, the following topics will be covered: the Military and Aerospace Applications of Programmable Devices and Technologies Conference to be held at GSFC in September, 1998, proton test results, and some total dose results.

Design of automata theory of cubical complexes with applications to diagnosis and algorithmic description

NASA Technical Reports Server (NTRS)

Roth, J. P.

1972-01-01

Methods for development of logic design together with algorithms for failure testing, a method for design of logic for ultra-large-scale integration, extension of quantum calculus to describe the functional behavior of a mechanism component-by-component and to computer tests for failures in the mechanism using the diagnosis algorithm, and the development of an algorithm for the multi-output 2-level minimization problem are discussed.

Trust Management and Security in Satellite Telecommand Processing

DTIC Science & Technology

2011-03-24

include XREP, NICE, and P- Grid . These systems aggregate the perception of entities in the system to calculate a local reputation value for a specific...peripheral used is a Universal Asynchronous Receiver Transmitter ( UART ) which is connected to a Recommended Standard 232 (RS232) transceiver onboard [49...satellite, a logic analyzer was connected to monitor UART signals on the test board. The logic analyzer used for this testing was a USBee ZX module

JPRS Report, Science & Technology, Japan, Key Tech Center Advanced Communications Research

DTIC Science & Technology

1990-02-26

networks. 27 b. Fuzzy access Even when correct information regarding the connection destination is not available, this makes it possible to establish...a connection based on the stored fuzzy information. c. Logical accessing Makes it possible to effect a connection based on the logical name (indivi...understand fuzzy indications from the user. (b) Normality check tests The following tests should be conducted to check the normality of user- defined services

Profile of mathematical reasoning ability of 8th grade students seen from communicational ability, basic skills, connection, and logical thinking

NASA Astrophysics Data System (ADS)

Sumarsih; Budiyono; Indriati, D.

2018-04-01

This research aims to understand the students’ weaknesses in mathematical reasoning ability in junior secondary school. A set of multiple choice tests were used to measure this ability involve components mathematical communication, basic skills, connection, and logical thinking. A total of 259 respondents were determined by stratified cluster random sampling. Data were analyzed using one-way Anova test with Fobs = 109.5760 and F = 3.0000. The results show that students’ ability from schools with high National Exam in mathematics category was the best and followed by medium and low category. Mathematical connection is the most difficult component performed by students. In addition, most students also have difficulty in expressing ideas and developing logical arguments.

Enhancement of mechanical properties of 123 superconductors

DOEpatents

Balachandran, Uthamalingam

1995-01-01

A composition and method of preparing YBa.sub.2 Cu.sub.3 O.sub.7-x superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T.sub.c. About 5-20% additions give rise to substantially improved mechanical properties.

Topological Quantum Information Processing Mediated Via Hybrid Topological Insulator Structures

DTIC Science & Technology

2013-11-13

manipulation, entanglement and detection ofMajorana fermions in diamond-topological insulator - superconductor heterojunctions. Furthennore, we propose to...the formation, manipulation, entanglement and detection of Majorana fermions in diamond-topological insulator - superconductor heterojunctions...Interactions between Superconductors and Topological Insulators Recent advances have revealed a new type of information processing, topological quantum

Topological Quantum Information Processing Mediated Via Hybrid Topogical Insulator Structures

DTIC Science & Technology

2014-03-28

formation, manipulation, entanglement and detection of Majorana fermions in diamond-topological insulator - superconductor heterojunctions. Furthermore...between Superconductors and Topological Insulators Recent advances have revealed a new type of information processing, topological quantum...Topological Insulator - Superconductor Heterostructures," Physical Review B 84, 144507 (2011). 7 Hsiang-Hsuan Hung, Pouyan Ghaemi, Taylor L

Superconductors in the High School Classroom

ERIC Educational Resources Information Center

Lincoln, James

2017-01-01

In this article, we discuss the behavior of high-temperature superconductors and how to demonstrate them safely and effectively in the high school or introductory physics classroom. Included here is a discussion of the most relevant physics topics that can be demonstrated, some safety tips, and a bit of the history of superconductors. In an effort…

Fully gapped superconductivity in In-doped topological crystalline insulator Pb 0.5Sn 0.5Te

DOE PAGES

Du, Guan; Gu, G. D.; Du, Zengyi; ...

2015-07-27

In this study, superconductors derived from topological insulators and topological crystalline insulators by chemical doping have long been considered to be candidates as topological superconductors. Pb 0.5Sn 0.5Te is a topological crystalline insulator with mirror symmetry protected surface states on (001)-, (011)-, and (111)-oriented surfaces. The superconductor (Pb 0.5Sn 0.5) 0.7In 0.3Te is produced by In doping in Pb 0.5Sn 0.5Te, and is thought to be a topological superconductor. Here we report scanning tunneling spectroscopy measurements of the superconducting state as well as the superconducting energy gap in (Pb 0.5Sn 0.5) 0.7In 0.3Te on a (001)-oriented surface. The spectrum canmore » be well fitted by an anisotropic s-wave gap function of Δ = 0.72 + 0.18cos4θ meV using Dynes model. The results show that the superconductor seems to be a fully gapped one without any in-gap states, in contradiction with the expectation of a topological superconductor.« less

Experimental evidence for s-wave pairing symmetry in superconducting Cu(x)Bi2Se3 single crystals using a scanning tunneling microscope.

PubMed

Levy, Niv; Zhang, Tong; Ha, Jeonghoon; Sharifi, Fred; Talin, A Alec; Kuk, Young; Stroscio, Joseph A

2013-03-15

Topological superconductors represent a newly predicted phase of matter that is topologically distinct from conventional superconducting condensates of Cooper pairs. As a manifestation of their topological character, topological superconductors support solid-state realizations of Majorana fermions at their boundaries. The recently discovered superconductor Cu(x)Bi(2)Se(3) has been theoretically proposed as an odd-parity superconductor in the time-reversal-invariant topological superconductor class, and point-contact spectroscopy measurements have reported the observation of zero-bias conductance peaks corresponding to Majorana states in this material. Here we report scanning tunneling microscopy measurements of the superconducting energy gap in Cu(x)Bi(2)Se(3) as a function of spatial position and applied magnetic field. The tunneling spectrum shows that the density of states at the Fermi level is fully gapped without any in-gap states. The spectrum is well described by the Bardeen-Cooper-Schrieffer theory with a momentum independent order parameter, which suggests that Cu(x)Bi(2)Se(3) is a classical s-wave superconductor contrary to previous expectations and measurements.

Classification of reflection-symmetry-protected topological semimetals and nodal superconductors

NASA Astrophysics Data System (ADS)

Chiu, Ching-Kai; Schnyder, Andreas P.

2014-11-01

While the topological classification of insulators, semimetals, and superconductors in terms of nonspatial symmetries is well understood, less is known about topological states protected by crystalline symmetries, such as mirror reflections and rotations. In this work, we systematically classify topological semimetals and nodal superconductors that are protected, not only by nonspatial (i.e., global) symmetries, but also by a crystal reflection symmetry. We find that the classification crucially depends on (i) the codimension of the Fermi surface (nodal line or point) of the semimetal (superconductor), (ii) whether the mirror symmetry commutes or anticommutes with the nonspatial symmetries, and (iii) how the Fermi surfaces (nodal lines or points) transform under the mirror reflection and nonspatial symmetries. The classification is derived by examining all possible symmetry-allowed mass terms that can be added to the Bloch or Bogoliubov-de Gennes Hamiltonian in a given symmetry class and by explicitly deriving topological invariants. We discuss several examples of reflection-symmetry-protected topological semimetals and nodal superconductors, including topological crystalline semimetals with mirror Z2 numbers and topological crystalline nodal superconductors with mirror winding numbers.

Simulation and experiment of a fuzzy logic based MPPT controller for a small wind turbine system

NASA Astrophysics Data System (ADS)

Petrila, Diana; Muntean, Nicolae

2012-09-01

This paper describes the development of a fuzzy logic based maximum power point tracking (MPPT) strategy for a variable speed wind turbine system (VSWT). For this scope, a fuzzy logic controller (FLC) was described, simulated and tested on a real time "hardware in the loop" wind turbine emulator. Simulation and experimental results show that the controller is able to track the maximum power point for various wind conditions and validate the proposed control strategy.

EAGLE Monitors by Collecting Facts and Generating Obligations

NASA Technical Reports Server (NTRS)

Barrnger, Howard; Goldberg, Allen; Havelund, Klaus; Sen, Koushik

2003-01-01

We present a rule-based framework, called EAGLE, that has been shown to be capable of defining and implementing a range of finite trace monitoring logics, including future and past time temporal logic, extended regular expressions, real-time and metric temporal logics, interval logics, forms of quantified temporal logics, and so on. A monitor for an EAGLE formula checks if a finite trace of states satisfies the given formula. We present, in details, an algorithm for the synthesis of monitors for EAGLE. The algorithm is implemented as a Java application and involves novel techniques for rule definition, manipulation and execution. Monitoring is achieved on a state-by-state basis avoiding any need to store the input trace of states. Our initial experiments have been successful as EAGLE detected a previously unknown bug while testing a planetary rover controller.

Cryocooler based test setup for high current applications

NASA Astrophysics Data System (ADS)

Pradhan, Jedidiah; Das, Nisith Kr.; Roy, Anindya; Duttagupta, Anjan

2018-04-01

A cryo-cooler based cryogenic test setup has been designed, fabricated, and tested. The setup incorporates two numbers of cryo-coolers, one for sample cooling and the other one for cooling the large magnet coil. The performance and versatility of the setup has been tested using large samples of high-temperature superconductor magnet coil as well as short samples with high current. Several un-calibrated temperature sensors have been calibrated using this system. This paper presents the details of the system along with results of different performance tests.

Two-step complete polarization logic Bell-state analysis.

PubMed

Sheng, Yu-Bo; Zhou, Lan

2015-08-26

The Bell state plays a significant role in the fundamental tests of quantum mechanics, such as the nonlocality of the quantum world. The Bell-state analysis is of vice importance in quantum communication. Existing Bell-state analysis protocols usually focus on the Bell-state encoding in the physical qubit directly. In this paper, we will describe an alternative approach to realize the near complete logic Bell-state analysis for the polarized concatenated Greenberger-Horne-Zeilinger (C-GHZ) state with two logic qubits. We show that the logic Bell-state can be distinguished in two steps with the help of the parity-check measurement (PCM) constructed by the cross-Kerr nonlinearity. This approach can be also used to distinguish arbitrary C-GHZ state with N logic qubits. As both the recent theoretical and experiment work showed that the C-GHZ state has its robust feature in practical noisy environment, this protocol may be useful in future long-distance quantum communication based on the logic-qubit entanglement.

Theory for measurements of penetration depth in magnetic superconductors by magnetic force microscopy and scanning SQUID microscopy

NASA Astrophysics Data System (ADS)

Lin, Shi-Zeng; Bulaevskii, Lev N.

2012-07-01

The working principle of magnetic force microscopy and scanning SQUID microscopy is introducing a magnetic source near a superconductor and measuring the magnetic field distribution near the superconductor, from which one can obtain the penetration depth. We investigate the magnetic field distribution near the surface of a magnetic superconductor when a magnetic source is placed close to the superconductor, which can be used to extract both the penetration depth λL and magnetic susceptibility χ by magnetic force microscopy or scanning SQUID microscopy. When the magnetic moments are parallel to the surface, one extracts λL/1-4πχ. When the moments are perpendicular to the surface, one obtains λL. By changing the orientation of the crystal, one thus is able to extract both χ and λL.

Second-Generation High-Temperature Superconductor Wires for the Electric Power Grid

NASA Astrophysics Data System (ADS)

Malozemoff, A. P.

2012-08-01

Superconductors offer major advantages for the electric power grid, including high current and power capacity, high efficiency arising from the lossless current flow, and a unique current-limiting functionality arising from a superconductor-to-resistive transition. These advantages can be brought to bear on equipment such as underground power cables, fault current limiters, rotating machinery, transformers, and energy storage. The first round of significant commercial-scale superconductor power-equipment demonstrations, carried out during the past decade, relied on a first-generation high-temperature superconductor (HTS) wire. However, during the past few years, with the recent commercial availability of high-performance second-generation HTS wires, power-equipment demonstrations have increasingly been carried out with these new wires, which bring important advantages. The foundation is being laid for commercial expansion of this important technology into the power grid.

Philosophic Heuristic Instruction (PHI)--III.

ERIC Educational Resources Information Center

Coole, Walter A.

This publication contains a course outline, syllabus, and self-study units finished and partly tested in the Open Classroom, an auto-tutorial learning laboratory at Skagit Valley College (Washington). This self-contained course in elementary formal logic is designed for use in conjunction with Kalish and Montague's "Logic--Techniques of…

Hyper- and hypobaric processing of Tl-Ba-Ca-Cu-O superconductors

NASA Astrophysics Data System (ADS)

Goretta, K. C.; Routbort, J. L.; Shi, Donglu; Chen, J. G.; Hash, M. C.

1989-11-01

Tl-based superconductors of initial composition Tl:Ca:Ba:Cu equal to 2:2:2:3 and 1:3:1:3 were heated in oxygen at pressures of 10(sup 4) to 6 (times) 10(sup 5) Pa. The 2:2:2:3 composition formed primarily the 2-layer superconductor with zero resistance from 77 to 104 K. The 1:3:1:3 composition formed nearly phase pure 3-layer superconductor with a maximum zero resistance temperature of 120 K. Application of hyperbaric pressure influenced phase purities and transition temperatures slightly; phase purities decreased significantly with application of hypobaric pressures.

Fabrication of high-quality superconductor-insulator-superconductor junctions on thin SiN membranes

NASA Technical Reports Server (NTRS)

Garcia, Edouard; Jacobson, Brian R.; Hu, Qing

1993-01-01

We have successfully fabricated high-quality and high-current density superconductor-insulator-superconductor (SIS) junctions on freestanding thin silicon nitride (SIN) membranes. These devices can be used in a novel millimeter-wave and THz receiver system which is made using micromachining. The SIS junctions with planar antennas were fabricated first on a silicon wafer covered with a SiN membrane, the Si wafer underneath was then etched away using an anisotropic KOH etchant. The current-voltage characteristics of the SIS junctions remained unchanged after the whole process, and the junctions and the membrane survived thermal cycling.

Automatic HTS force measurement instrument

DOEpatents

Sanders, S.T.; Niemann, R.C.

1999-03-30

A device is disclosed for measuring the levitation force of a high temperature superconductor sample with respect to a reference magnet includes a receptacle for holding several high temperature superconductor samples each cooled to superconducting temperature. A rotatable carousel successively locates a selected one of the high temperature superconductor samples in registry with the reference magnet. Mechanism varies the distance between one of the high temperature superconductor samples and the reference magnet, and a sensor measures levitation force of the sample as a function of the distance between the reference magnet and the sample. A method is also disclosed. 3 figs.

Anisotropic effect of the magnetic sensor formed from metal/high-Tc superconductor contact

NASA Astrophysics Data System (ADS)

Miyake, S.; Aoyama, T.; Suzuki, Y.; Kusaka, T.; Yotsuya, T.

1991-03-01

The magnetic sensor formed via a metal/high-Tc superconductor small contact shows anisotropic properties below the lower critical field. An Ag wire was connected directly to the superconductor by an ultrasonic bonding method. It is shown that the resistance was changed by the field parallel to the superconductor surface, while it was not affected by the vertical field. The change is estimated to be 5 x 10 to the -5th ohm/G. No hysteresis is observed. Magnetic field direction can be detected by using these properties and a deferential measuring method of the resistance.

Large area bulk superconductors

DOEpatents

Miller, Dean J.; Field, Michael B.

2002-01-01

A bulk superconductor having a thickness of not less than about 100 microns is carried by a polycrystalline textured substrate having misorientation angles at the surface thereof not greater than about 15.degree.; the bulk superconductor may have a thickness of not less than about 100 microns and a surface area of not less than about 50 cm.sup.2. The textured substrate may have a thickness not less than about 10 microns and misorientation angles at the surface thereof not greater than about 15.degree.. Also disclosed is a process of manufacturing the bulk superconductor and the polycrystalline biaxially textured substrate material.

On the Mechanism for a Gravity Effect Using Type 2 Superconductors

NASA Technical Reports Server (NTRS)

Robertson, Glen A.

1999-01-01

In this paper, we formulate a percent mass change equation based on Woodward's transient mass shift and the Cavendish balance equations applied to superconductor Josephson junctions, A correction to the transient mass shift equation is presented due to the emission of the mass energy from the superconductor. The percentage of mass change predicted by the equation was estimated against the maximum percent mass change reported by Podkletnov in his gravity shielding experiments. An experiment is then discussed, which could shed light on the transient mass shift near superconductor and verify the corrected gravitational potential.

The use of high temperature superconductors to levitate lunar telescope

NASA Technical Reports Server (NTRS)

Brown, Beth A.

1992-01-01

The objective of this paper was to assist in the construction of a lunar telescope mirror model by conducting research on composite materials and other lightweight, rigid materials, and by determining how much weight can be levitated by available superconductors. It is believed that with the construction of four magnets suspended over four bulk superconductors (or vice versa), there should be no problems lifting a model mirror and stabilizing it at different positions. It may be necessary to increase the size and quality of the superconductors and/or magnets in order to achieve this.

Superconductors in the high school classroom

NASA Astrophysics Data System (ADS)

Lincoln, James

2017-11-01

In this article, we discuss the behavior of high-temperature superconductors and how to demonstrate them safely and effectively in the high school or introductory physics classroom. Included here is a discussion of the most relevant physics topics that can be demonstrated, some safety tips, and a bit of the history of superconductors. In an effort to include first-year physics students in the world of modern physics, a topic as engaging as superconductivity should not be missed. It is an opportunity to inspire students to study physics through the myriad of possible applications that high temperature superconductors hold for the future.

Synthesis of highly phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor

DOEpatents

Dorris, S.E.; Poeppel, R.B.; Prorok, B.C.; Lanagan, M.T.; Maroni, V.A.

1994-10-11

An article and method of manufacture of (Bi,Pb)-Sr-Ca-Cu-O superconductor are disclosed. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi,Pb)-Sr-Ca-Cu-O superconductor. 5 figs.

Rotordynamic Characterization of a Hybrid Superconductor Magnet Bearing

NASA Technical Reports Server (NTRS)

Ma, Ki B.; Xia, Zule H.; Cooley, Rodger; Fowler, Clay; Chu, Wei-Kan

1996-01-01

A hybrid superconductor magnet bearing uses magnetic forces between permanent magnets to provide lift and the flux pinning force between permanent magnets and superconductors to stabilize against instabilities intrinsic to the magnetic force between magnets. We have constructed a prototype kinetic energy storage system, using a hybrid superconductor magnet bearing to support a 42 lb. flywheel at the center. With five sensors on the periphery of the flywheel, we have monitored the position and attitude of the flywheel during its spin down. The results indicate low values of stiffnesses for the bearing. The implications of this and other consequences will be discussed.

Modelling default and likelihood reasoning as probabilistic

NASA Technical Reports Server (NTRS)

Buntine, Wray

1990-01-01

A probabilistic analysis of plausible reasoning about defaults and about likelihood is presented. 'Likely' and 'by default' are in fact treated as duals in the same sense as 'possibility' and 'necessity'. To model these four forms probabilistically, a logic QDP and its quantitative counterpart DP are derived that allow qualitative and corresponding quantitative reasoning. Consistency and consequence results for subsets of the logics are given that require at most a quadratic number of satisfiability tests in the underlying propositional logic. The quantitative logic shows how to track the propagation error inherent in these reasoning forms. The methodology and sound framework of the system highlights their approximate nature, the dualities, and the need for complementary reasoning about relevance.

Logic Design Pathology and Space Flight Electronics

NASA Technical Reports Server (NTRS)

Katz, Richard; Barto, Rod L.; Erickson, K.

1997-01-01

Logic design errors have been observed in space flight missions and the final stages of ground test. The technologies used by designers and their design/analysis methodologies will be analyzed. This will give insight to the root causes of the failures. These technologies include discrete integrated circuit based systems, systems based on field and mask programmable logic, and the use computer aided engineering (CAE) systems. State-of-the-art (SOTA) design tools and methodologies will be analyzed with respect to high-reliability spacecraft design and potential pitfalls are discussed. Case studies of faults from large expensive programs to "smaller, faster, cheaper" missions will be used to explore the fundamental reasons for logic design problems.

Towards An Engineering Discipline of Computational Security

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mili, Ali; Sheldon, Frederick T; Jilani, Lamia Labed

2007-01-01

George Boole ushered the era of modern logic by arguing that logical reasoning does not fall in the realm of philosophy, as it was considered up to his time, but in the realm of mathematics. As such, logical propositions and logical arguments are modeled using algebraic structures. Likewise, we submit that security attributes must be modeled as formal mathematical propositions that are subject to mathematical analysis. In this paper, we approach this problem by attempting to model security attributes in a refinement-like framework that has traditionally been used to represent reliability and safety claims. Keywords: Computable security attributes, survivability, integrity,more » dependability, reliability, safety, security, verification, testing, fault tolerance.« less

Hybrid quantum logic and a test of Bell's inequality using two different atomic isotopes.

PubMed

Ballance, C J; Schäfer, V M; Home, J P; Szwer, D J; Webster, S C; Allcock, D T C; Linke, N M; Harty, T P; Aude Craik, D P L; Stacey, D N; Steane, A M; Lucas, D M

2015-12-17

Entanglement is one of the most fundamental properties of quantum mechanics, and is the key resource for quantum information processing (QIP). Bipartite entangled states of identical particles have been generated and studied in several experiments, and post-selected or heralded entangled states involving pairs of photons, single photons and single atoms, or different nuclei in the solid state, have also been produced. Here we use a deterministic quantum logic gate to generate a 'hybrid' entangled state of two trapped-ion qubits held in different isotopes of calcium, perform full tomography of the state produced, and make a test of Bell's inequality with non-identical atoms. We use a laser-driven two-qubit gate, whose mechanism is insensitive to the qubits' energy splittings, to produce a maximally entangled state of one (40)Ca(+) qubit and one (43)Ca(+) qubit, held 3.5 micrometres apart in the same ion trap, with 99.8 ± 0.6 per cent fidelity. We test the CHSH (Clauser-Horne-Shimony-Holt) version of Bell's inequality for this novel entangled state and find that it is violated by 15 standard deviations; in this test, we close the detection loophole but not the locality loophole. Mixed-species quantum logic is a powerful technique for the construction of a quantum computer based on trapped ions, as it allows protection of memory qubits while other qubits undergo logic operations or are used as photonic interfaces to other processing units. The entangling gate mechanism used here can also be applied to qubits stored in different atomic elements; this would allow both memory and logic gate errors caused by photon scattering to be reduced below the levels required for fault-tolerant quantum error correction, which is an essential prerequisite for general-purpose quantum computing.

A hidden pseudogap under the 'dome' of superconductivity in electron-doped high-temperature superconductors.

PubMed

Alff, L; Krockenberger, Y; Welter, B; Schonecke, M; Gross, R; Manske, D; Naito, M

2003-04-17

The ground state of superconductors is characterized by the long-range order of condensed Cooper pairs: this is the only order present in conventional superconductors. The high-transition-temperature (high-T(c)) superconductors, in contrast, exhibit more complex phase behaviour, which might indicate the presence of other competing ground states. For example, the pseudogap--a suppression of the accessible electronic states at the Fermi level in the normal state of high-T(c) superconductors-has been interpreted as either a precursor to superconductivity or as tracer of a nearby ground state that can be separated from the superconducting state by a quantum critical point. Here we report the existence of a second order parameter hidden within the superconducting phase of the underdoped (electron-doped) high-T(c) superconductor Pr2-xCe(x)CuO4-y and the newly synthesized electron-doped material La2-xCe(x)CuO4-y (ref. 8). The existence of a pseudogap when superconductivity is suppressed excludes precursor superconductivity as its origin. Our observation is consistent with the presence of a (quantum) phase transition at T = 0, which may be a key to understanding high-T(c) superconductivity. This supports the picture that the physics of high-T(c) superconductors is determined by the interplay between competing and coexisting ground states.

Electric field effect in superconductor-ferroelectric structures

NASA Technical Reports Server (NTRS)

Lemanov, V. V.

1995-01-01

Electric field effect (the E-effect) in superconductors has been studied since 1960 when Glover and Sherill published their results on a shift of the critical temperature T(sub c) about 0.1 mK in Sn and In thin films under the action Off the field E=300 kV/cm. Stadler was the first to study the effect or spontaneous polarization of ferroelectric substrate on the electric properties of superconductors. He observed that the reversal of polarization of TGS substrate under action of external electric field in Sn-TGS structures induced the T(sub c) shift in Sn about 1.3 mK. Since in this case the effect is determined not by the electric field but by the spontaneous polarization, we may call this effect the P-effect. High-T(sub c) superconductors opened the new possibilities to study the E- and P-effects due to low charge carrier density, as compared to conventional superconductors, and to anomalously small coherence length. Experiments in this field began in many laboratories but a breakthrough was made where a shift in T(sub c) by 50 mK was observed in YBCO thin films. Much higher effects were observed in subsequent studies. The first experiments on the P-effect in high-T(sub c) superconductors were reported elsewhere. In this report we shall give a short description of study on the P-effect in high-T(sub c) superconductors.

The first man-loading high temperature superconducting Maglev test vehicle in the world

NASA Astrophysics Data System (ADS)

Wang, Jiasu; Wang, Suyu; Zeng, Youwen; Huang, Haiyu; Luo, Fang; Xu, Zhipei; Tang, Qixue; Lin, Guobin; Zhang, Cuifang; Ren, Zhongyou; Zhao, Guomin; Zhu, Degui; Wang, Shaohua; Jiang, He; Zhu, Min; Deng, Changyan; Hu, Pengfei; Li, Chaoyong; Liu, Fang; Lian, Jisan; Wang, Xiaorong; Wang, Lianghui; Shen, Xuming; Dong, Xiaogang

2002-10-01

The first man-loading high temperature superconducting Maglev test vehicle in the world is reported. This vehicle was first tested successfully on December 31, 2000 in the Applied Superconductivity Laboratory, Southwest Jiaotong University, China. Heretofore over 17,000 passengers took the vehicle, and it operates very well from beginning to now. The function of suspension is separated from one of propulsion. The high temperature superconducting Maglev provides inherent stable forces both in the levitation and in the guidance direction. The vehicle is 3.5 m long, 1.2 m wide, and 0.8 m high. When five people stand on vehicle and the total weight is 530 kg, the net levitation gap is more than 20 mm. The whole vehicle system includes three parts, vehicle body, guideway and controlling system. The high temperature superconducting Maglev equipment on board is the most important for the system. The onboard superconductors are melt-textured YBaCuO bulks. The superconductors are fixed on the bottom of liquid nitrogen vessels and cooled by liquid nitrogen. The guideway consists of two parallel permanent magnetic tracks, whose surface concentrating magnetic field is up to 1.2 T. The guideway is 15.5 m long.

Contactless system of excitation current measurement in the windings with high inductance

NASA Astrophysics Data System (ADS)

Chubraeva, L.; Evseev, E.; Timofeev, S.

2018-02-01

The results of development, manufacturing and testing of a special contactless maintenance-free excitation current measurement system intended for the windings with high inductance, typical for superconductive alternators, are presented. The system was assembled on the brushless exciter is intended for 1 MVA wind-power generator with the winding, manufactured of high-temperature superconductors (HTSC). The alternator with brushless exciter were manufactured and successfully tested.

Experiments in a real scale maglev vehicle prototype

NASA Astrophysics Data System (ADS)

Sotelo, G. G.; Dias, D. H. N.; Machado, O. J.; David, E. D.; de Andrade, R., Jr.; Stephan, R. M.; Costa, G. C.

2010-06-01

A Brazilian real scale magnetically levitated transport system prototype is under development at the Federal University of Rio de Janeiro. To test this system a 180 m long line has been projected and it will be concluded by the end of 2010. A superconducting linear bearing (SLB) is used to replace the wheels of a conventional train. High temperature superconductor bulks placed inside cryostats attached to the vehicle and a magnetic rail composes the SLB. To choose the magnetic rail for the test line three different rails, selected in a previous simulation work, were built and tested. They are composed by Nd-Fe-B and steel, arranged in a flux concentrator topology. The magnetic flux density for those magnetic rails was mapped. Also, the levitation force between those rails and the superconductor cryostat, for several cooling gaps, were measured to select the best rail geometry to be used in the real scale line. The SLB allows building a light vehicle with distributed load, silent and high energy efficient. The proposed vehicle is composed of four modules with just 1.5 m of length each one and it can transport up to 24 passengers. The test line having two curves with 45 m radius and a 15% acclivity ramp is also presented.

Nodal lines and nodal loops in nonsymmorphic odd-parity superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Micklitz, T.; Norman, M. R.

2017-01-01

We discuss the nodal structure of odd-parity superconductors in the presence of nonsymmorphic crystal symmetries, both with and without spin-orbit coupling, and with and without time-reversal symmetry. We comment on the relation of our work to previous work in the literature, and also the implications for unconventional superconductors such as UPt3.

X-ray photoemission study of the infinite-layer cuprate superconductor Sr(0.9) La (0.1) CuO(2)

NASA Technical Reports Server (NTRS)

Vasquez, R. P.; Jung, C. U.; Kim, J. Y.; Kim, M. S.; Lee, S. Y.; Lee, S. I.

2001-01-01

The electron-doped infinite-layer superconductor Sr(0.9)La(0.1) CuO(2) is studied with x-ray photoemission spectroscopy (XPS). A nonaqueous chemical etchant is shown to effectively remove contaminants and to yield surfaces from which signals intrinsic to the superconductor dominate.

Preparation of Bi-Sr-Ca-Cu-O superconductors from oxide-glass precursors

DOEpatents

Hinks, David G.; Capone, II, Donald W.

1992-01-01

A superconductor and precursor therefor from oxide mixtures of Ca, Sr, Bi and Cu. Glass precursors quenched to elevated temperatures result in glass free of crystalline precipitates having enhanced mechanical properties. Superconductors are formed from the glass precursors by heating in the presence of oxygen to a temperature below the melting point of the glass.

Enhancement of mechanical properties of 123 superconductors

DOEpatents

Balachandran, U.

1995-04-25

A composition and method are disclosed of preparing YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T{sub c}. About 5-20% additions give rise to substantially improved mechanical properties.

High-T(sub c) Superconductor-Normal-Superconductor Junctions with Polyimide-Passivated Ambient Temperature Edge Formation

NASA Technical Reports Server (NTRS)

Barner, J. B.; Kleinsasser, A. W.; Hunt, B. D.

1996-01-01

The ability to controllably fabricate High-Temperature Superconductor (HTS) S-Normal-S (SNS) Josephson Juntions (JJ's) enhances the possibilities fro many applications, including digital circuits, SQUID's, and mixers. A wide variety of approaches to fabricating SNS-like junctions has been tried and analyzed in terms of proximity effect behavior.

Micro-mechanical resonators for dynamically reconfigurable reduced voltage logic gates

NASA Astrophysics Data System (ADS)

Chappanda, K. N.; Ilyas, S.; Younis, M. I.

2018-05-01

Due to the limitations of transistor-based logic devices such as their poor performance at elevated temperature, alternative computing methods are being actively investigated. In this work, we present electromechanical logic gates using electrostatically coupled in-plane micro-cantilever resonators operated at modest vacuum conditions of 5 Torr. Operating in the first resonant mode, we demonstrate 2-bit XOR, 2- and 3-bit AND, 2- and 3-bit NOR, and 1-bit NOT gates; all condensed in the same device. Through the designed electrostatic coupling, the required voltage for the logic gates is reduced by 80%, along with the reduction in the number of electrical interconnects and devices per logic operation (contrary to transistors). The device is dynamically reconfigurable between any logic gates in real time without the need for any change in the electrical interconnects and the drive circuit. By operating in the first two resonant vibration modes, we demonstrate mechanical logic gates consisting of two 2-bit AND and two 2-bit XOR gates. The device is tested at elevated temperatures and is shown to be functional as a logic gate up to 150 °C. Also, the device has high reliability with demonstrated lifetime greater than 5  ×  1012 oscillations.

Response-Time Tests of Logical-Rule Models of Categorization

ERIC Educational Resources Information Center

Little, Daniel R.; Nosofsky, Robert M.; Denton, Stephen E.

2011-01-01

A recent resurgence in logical-rule theories of categorization has motivated the development of a class of models that predict not only choice probabilities but also categorization response times (RTs; Fific, Little, & Nosofsky, 2010). The new models combine mental-architecture and random-walk approaches within an integrated framework and…

Using Symbolic-Logic Matrices To Improve Confirmatory Factor Analysis Techniques.

ERIC Educational Resources Information Center

Creighton, Theodore B.; Coleman, Donald G.; Adams, R. C.

A continuing and vexing problem associated with survey instrument development is the creation of items, initially, that correlate favorably a posteriori with constructs being measured. This study tests the use of symbolic-logic matrices developed by D. G. Coleman (1979) in creating factorially "pure" statistically discrete constructs in…

Some Personality Correlates of Logical Reasoning Ability.

ERIC Educational Resources Information Center

Ross, G. Robert, Jr.; Fletcher, Harold J.

Four-hundred and nine students (grades 8, 10, 12 and 14) were given logical syllogism problems of the form "If p...then q" along with tests of dogmatism and intolerance of ambiguity. Aptitude scores were also obtained. Major results indicated that expressed dogmatism and intolerance of ambiguity were negatively correlated with syllogistic…

Performance of ceramic superconductors in magnetic bearings

NASA Technical Reports Server (NTRS)

Kirtley, James L., Jr.; Downer, James R.

1993-01-01

Magnetic bearings are large-scale applications of magnet technology, quite similar in certain ways to synchronous machinery. They require substantial flux density over relatively large volumes of space. Large flux density is required to have satisfactory force density. Satisfactory dynamic response requires that magnetic circuit permeances not be too large, implying large air gaps. Superconductors, which offer large magnetomotive forces and high flux density in low permeance circuits, appear to be desirable in these situations. Flux densities substantially in excess of those possible with iron can be produced, and no ferromagnetic material is required. Thus the inductance of active coils can be made low, indicating good dynamic response of the bearing system. The principal difficulty in using superconductors is, of course, the deep cryogenic temperatures at which they must operate. Because of the difficulties in working with liquid helium, the possibility of superconductors which can be operated in liquid nitrogen is thought to extend the number and range of applications of superconductivity. Critical temperatures of about 98 degrees Kelvin were demonstrated in a class of materials which are, in fact, ceramics. Quite a bit of public attention was attracted to these new materials. There is a difficulty with the ceramic superconducting materials which were developed to date. Current densities sufficient for use in large-scale applications have not been demonstrated. In order to be useful, superconductors must be capable of carrying substantial currents in the presence of large magnetic fields. The possible use of ceramic superconductors in magnetic bearings is investigated and discussed and requirements that must be achieved by superconductors operating at liquid nitrogen temperatures to make their use comparable with niobium-titanium superconductors operating at liquid helium temperatures are identified.

Assessment of Evidence-based Management Training Program: Application of a Logic Model.

PubMed

Guo, Ruiling; Farnsworth, Tracy J; Hermanson, Patrick M

2016-06-01

The purposes of this study were to apply a logic model to plan and implement an evidence-based management (EBMgt) educational training program for healthcare administrators and to examine whether a logic model is a useful tool for evaluating the outcomes of the educational program. The logic model was used as a conceptual framework to guide the investigators in developing an EBMgt educational training program and evaluating the outcomes of the program. The major components of the logic model were constructed as inputs, outputs, and outcomes/impacts. The investigators delineated the logic model based on the results of the needs assessment survey. Two 3-hour training workshops were delivered to 30 participants. To assess the outcomes of the EBMgt educational program, pre- and post-tests and self-reflection surveys were conducted. The data were collected and analyzed descriptively and inferentially, using the IBM Statistical Package for the Social Sciences (SPSS) 22.0. A paired sample t-test was performed to compare the differences in participants' EBMgt knowledge and skills prior to and after the training. The assessment results showed that there was a statistically significant difference in participants' EBMgt knowledge and information searching skills before and after the training (p< 0.001). Participants' confidence in using the EBMgt approach for decision-making was significantly increased after the training workshops (p< 0.001). Eighty-three percent of participants indicated that the knowledge and skills they gained through the training program could be used for future management decision-making in their healthcare organizations. The overall evaluation results of the program were positive. It is suggested that the logic model is a useful tool for program planning, implementation, and evaluation, and it also improves the outcomes of the educational program.

Passive microwave device applications of high T(c) superconducting thin films

NASA Astrophysics Data System (ADS)

Lyons, W. G.; Withers, R. S.

1990-11-01

Superconductors with a transition temperature T(c) from 40 K to 125 K are analyzed, with focus placed on their behavior around the boiling point of liquid nitrogen (77 K). It is shown that high-T(c) superconductors are similar to conventional type-II superconductors with paired holes instead of paired electrons. The nature of the electromagnetic response of a superconductor is illustrated with a two-fluid model, and surface resistance and conductor loss are assessed. Several microwave applications of high-T(c) superconductors are outlined including a six-pole dielectric loaded cavity filter used in multiplexers on current communication satellites and a four-pole superconducting filter. An implementation of a chirp filter using superconducting striplines with a cascaded array of backward-wave couplers to achieve a downchirp is presented as well as a 60-GHz phased antenna utilizing microstrip lines in the feed network.

Levitation of YBa2Cu3O(7-x) superconductor in a variable magnetic field

NASA Technical Reports Server (NTRS)

Terentiev, Alexander N.; Kuznetsov, Anatoliy A.

1992-01-01

The influence of both a linear alternating and rotational magnetic field component on the levitation behavior of a YBa2Cu3O(7-x) superconductor was examined. The transition from a plastic regime of levitation to an elastic one, induced by an alternating field component, was observed. An elastic regime in contrast to a plastic one is characterized by the unique position of stable levitation and field frequency dependence of relaxation time to this position. It was concluded that the vibrations of a magnet levitated above the superconductor can induce a transition from a plastic regime of levitation to an elastic one. It was found that a rotational magnetic field component induced rotations of a levitated superconductor. Rotational frictional motion of flux lines is likely to be an origin of torque developed. A prototype of a motor based on a levitated superconductor rotor is proposed.

A comparison of ASTROMAG coils made with aluminum and copper based superconductor

NASA Technical Reports Server (NTRS)

Green, M. A.

1991-01-01

The use of an aluminum matrix superconductor in the coils for the ASTROMAG magnet will increase the integrated field for conducting particle astrophysics experiments in space as compared to equal mass coils made with a copper matrix superconductor. The increased ability to detect charged particles can be achieved without decreasing the current margin of the superconductor in the coils. The use of a low-resistivity aluminum matrix conductor increases the energy needed to initiate a quench by two orders or magnitude. The current decay time constant during a quench is substantially increased. As a result, the quench energy dumped into the helium tank is reduced (the ASTROMAG coils are thermally decoupled from the helium tank), and the forces on the shield and shells due to eddy currents will be lower. A description is also given of the problems associated with the use of an aluminum matrix superconductor in the coils.

Unconventional Superconductivity in the BiS_{2}-Based Layered Superconductor NdO_{0.71}F_{0.29}BiS_{2}.

PubMed

Ota, Yuichi; Okazaki, Kozo; Yamamoto, Haruyoshi Q; Yamamoto, Takashi; Watanabe, Shuntaro; Chen, Chuangtian; Nagao, Masanori; Watauchi, Satoshi; Tanaka, Isao; Takano, Yoshihiko; Shin, Shik

2017-04-21

We investigate the superconducting-gap anisotropy in one of the recently discovered BiS_{2}-based superconductors, NdO_{0.71}F_{0.29}BiS_{2} (T_{c}∼5  K), using laser-based angle-resolved photoemission spectroscopy. Whereas the previously discovered high-T_{c} superconductors such as copper oxides and iron-based superconductors, which are believed to have unconventional superconducting mechanisms, have 3d electrons in their conduction bands, the conduction band of BiS_{2}-based superconductors mainly consists of Bi 6p electrons, and, hence, the conventional superconducting mechanism might be expected. Contrary to this expectation, we observe a strongly anisotropic superconducting gap. This result strongly suggests that the pairing mechanism for NdO_{0.71}F_{0.29}BiS_{2} is an unconventional one and we attribute the observed anisotropy to competitive or cooperative multiple paring interactions.

Manipulatable Andreev reflection due to the interplay between the DIII-class topological and s-wave superconductors

NASA Astrophysics Data System (ADS)

Wang, Xiao-Qi; Yi, Guang-Yu; Han, Yu; Jiang, Cui; Gong, Wei-Jiang

2018-07-01

We construct one mesoscopic circuit in which one quantum dot couples to one DIII-class topological superconductor and one s-wave superconductor, in addition to its connection with the metallic lead. And then, the Andreev reflection current in the metallic lead is evaluated. It is found that the two kinds of superconductors drive the Andreev reflection in the constructive manner. Next as finite superconducting phase difference is taken into account, the Andreev reflection oscillates in period π/2, and it can be suppressed in the low-energy region if the superconducting phase difference is (n + 1/2) π/2 (n ∈ Integer). Such a result is almost independent of the increase of the intradot Coulomb interaction. Therefore, this structure can assist to realize the manipulation of the Andreev reflection. Also, the result in this work provides useful information for understanding the property of the DIII-class topological superconductor.

Two-band induced superconductivity in single-layer graphene and topological insulator bismuth selenide

NASA Astrophysics Data System (ADS)

Talantsev, E. F.; Crump, W. P.; Tallon, J. L.

2018-01-01

Proximity-induced superconductivity in single-layer graphene (SLG) and in topological insulators represent almost ideal examples of superconductivity in two dimensions. Fundamental mechanisms governing superconductivity in the 2D limit are of central interest for modern condensed-matter physics. To deduce fundamental parameters of superconductor/graphene/superconductor and superconductor/bismuth selenide/superconductor junctions we investigate the self-field critical currents in these devices using the formalism of the Ambegaokar-Baratoff model. Our central finding is that the induced superconducting state in SLG and bismuth selenide each exhibits gapping on two superconducting bands. Based on recent results obtained on ultra-thin films of natural superconductors, including single-atomic layer of iron selenide, double and triple atomic layers of gallium, and several atomic layer tantalum disulphide, we conclude that a two-band induced superconducting state in SLG and bismuth selenide is part of a wider, more general multiple-band phenomenology of currently unknown origin.

Preparation of superconductor precursor powders

DOEpatents

Bhattacharya, R.

1998-08-04

A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic and/or reduced particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of all metals in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products. 7 figs.

Preparation of superconductor precursor powders

DOEpatents

Bhattacharya, Raghunath

1998-01-01

A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic and/or reduced particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of all metals in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products.

The non-equilibrium response of a superconductor to pair-breaking radiation measured over a broad frequency band

DOE Office of Scientific and Technical Information (OSTI.GOV)

Visser, P. J. de, E-mail: p.j.devisser@tudelft.nl; Yates, S. J. C.; Guruswamy, T.

2015-06-22

We have measured the absorption of terahertz radiation in a BCS superconductor over a broad range of frequencies from 200 GHz to 1.1 THz, using a broadband antenna-lens system and a tantalum microwave resonator. From low frequencies, the response of the resonator rises rapidly to a maximum at the gap edge of the superconductor. From there on, the response drops to half the maximum response at twice the pair-breaking energy. At higher frequencies, the response rises again due to trapping of pair-breaking phonons in the superconductor. In practice, this is a measurement of the frequency dependence of the quasiparticle creationmore » efficiency due to pair-breaking in a superconductor. The efficiency, calculated from the different non-equilibrium quasiparticle distribution functions at each frequency, is in agreement with the measurements.« less

Theoretical modeling of critical temperature increase in metamaterial superconductors

NASA Astrophysics Data System (ADS)

Smolyaninov, Igor I.; Smolyaninova, Vera N.

2016-05-01

Recent experiments have demonstrated that the metamaterial approach is capable of a drastic increase of the critical temperature Tc of epsilon near zero (ENZ) metamaterial superconductors. For example, tripling of the critical temperature has been observed in Al -A l2O3 ENZ core-shell metamaterials. Here, we perform theoretical modeling of Tc increase in metamaterial superconductors based on the Maxwell-Garnett approximation of their dielectric response function. Good agreement is demonstrated between theoretical modeling and experimental results in both aluminum- and tin-based metamaterials. Taking advantage of the demonstrated success of this model, the critical temperature of hypothetic niobium-, Mg B2- , and H2S -based metamaterial superconductors is evaluated. The Mg B2 -based metamaterial superconductors are projected to reach the liquid nitrogen temperature range. In the case of a H2S -based metamaterial Tc appears to reach ˜250 K.

Faster Evolution of More Multifunctional Logic Circuits

NASA Technical Reports Server (NTRS)

Stoica, Adrian; Zebulum, Ricardo

2005-01-01

A modification in a method of automated evolutionary synthesis of voltage-controlled multifunctional logic circuits makes it possible to synthesize more circuits in less time. Prior to the modification, the computations for synthesizing a four-function logic circuit by this method took about 10 hours. Using the method as modified, it is possible to synthesize a six-function circuit in less than half an hour. The concepts of automated evolutionary synthesis and voltage-controlled multifunctional logic circuits were described in a number of prior NASA Tech Briefs articles. To recapitulate: A circuit is designed to perform one of several different logic functions, depending on the value of an applied control voltage. The circuit design is synthesized following an automated evolutionary approach that is so named because it is modeled partly after the repetitive trial-and-error process of biological evolution. In this process, random populations of integer strings that encode electronic circuits play a role analogous to that of chromosomes. An evolved circuit is tested by computational simulation (prior to testing in real hardware to verify a final design). Then, in a fitness-evaluation step, responses of the circuit are compared with specifications of target responses and circuits are ranked according to how close they come to satisfying specifications. The results of the evaluation provide guidance for refining designs through further iteration.

Executing medical logic modules expressed in ArdenML using Drools.

PubMed

Jung, Chai Young; Sward, Katherine A; Haug, Peter J

2012-01-01

The Arden Syntax is an HL7 standard language for representing medical knowledge as logic statements. Despite nearly 2 decades of availability, Arden Syntax has not been widely used. This has been attributed to the lack of a generally available compiler to implement the logic, to Arden's complex syntax, to the challenges of mapping local data to data references in the Medical Logic Modules (MLMs), or, more globally, to the general absence of decision support in healthcare computing. An XML representation (ArdenML) may partially address the technical challenges. MLMs created in ArdenML can be converted into executable files using standard transforms written in the Extensible Stylesheet Language Transformation (XSLT) language. As an example, we have demonstrated an approach to executing MLMs written in ArdenML using the Drools business rule management system. Extensions to ArdenML make it possible to generate a user interface through which an MLM developer can test for logical errors.

Fuzzy logic feedback control for fed-batch enzymatic hydrolysis of lignocellulosic biomass.

PubMed

Tai, Chao; Voltan, Diego S; Keshwani, Deepak R; Meyer, George E; Kuhar, Pankaj S

2016-06-01

A fuzzy logic feedback control system was developed for process monitoring and feeding control in fed-batch enzymatic hydrolysis of a lignocellulosic biomass, dilute acid-pretreated corn stover. Digested glucose from hydrolysis reaction was assigned as input while doser feeding time and speed of pretreated biomass were responses from fuzzy logic control system. Membership functions for these three variables and rule-base were created based on batch hydrolysis data. The system response was first tested in LabVIEW environment then the performance was evaluated through real-time hydrolysis reaction. The feeding operations were determined timely by fuzzy logic control system and efficient responses were shown to plateau phases during hydrolysis. Feeding of proper amount of cellulose and maintaining solids content was well balanced. Fuzzy logic proved to be a robust and effective online feeding control tool for fed-batch enzymatic hydrolysis.

A new approach of active compliance control via fuzzy logic control for multifingered robot hand

NASA Astrophysics Data System (ADS)

Jamil, M. F. A.; Jalani, J.; Ahmad, A.

2016-07-01

Safety is a vital issue in Human-Robot Interaction (HRI). In order to guarantee safety in HRI, a model reference impedance control can be a very useful approach introducing a compliant control. In particular, this paper establishes a fuzzy logic compliance control (i.e. active compliance control) to reduce impact and forces during physical interaction between humans/objects and robots. Exploiting a virtual mass-spring-damper system allows us to determine a desired compliant level by understanding the behavior of the model reference impedance control. The performance of fuzzy logic compliant control is tested in simulation for a robotic hand known as the RED Hand. The results show that the fuzzy logic is a feasible control approach, particularly to control position and to provide compliant control. In addition, the fuzzy logic control allows us to simplify the controller design process (i.e. avoid complex computation) when dealing with nonlinearities and uncertainties.

Adiabatic quantum-flux-parametron cell library adopting minimalist design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takeuchi, Naoki, E-mail: takeuchi-naoki-kx@ynu.jp; Yamanashi, Yuki; Yoshikawa, Nobuyuki

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells inmore » the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.« less

Adiabatic quantum-flux-parametron cell library adopting minimalist design

NASA Astrophysics Data System (ADS)

Takeuchi, Naoki; Yamanashi, Yuki; Yoshikawa, Nobuyuki

2015-05-01

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells in the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.

Reflections on writing hydrologic reports

USGS Publications Warehouse

Olcott, Perry G.

1987-01-01

Reporting of scientific work should be characterized by a logical argument that is developed through presentation of the problem, tabulation and display of data pertinent to the problem , and testing and interpretation of the data to prove hypotheses that address the problem. Organization of the report is vital to developing this logical argument: it provides structure, continuity, logic, and emphasis to the presentation. Each part of the report serves a specific function and each is linked by a connecting logic, the logical argument of the report. Each scientific report normally has a title, table of contents, abstract, introduction, body (of the report), and summary and/or conclusions. Organization of sections within the body of the report is exactly parallel to overall organization; subjects presented in the section title are developed by logical subdivisions and pertinent discussion. The summary and/or conclusions section culminates the logical argument of the report by drawing together and quantitatively reiterating the principal conclusions developed in the discussion. Supplemental information on report content, background of the study, additional data or details on procedures, and other information of interest to the reader is presented in the foreward or preface, list of illustrations or tables, glossaries, and appendixes. (Lantz-PTT)

Logic, beliefs, and instruction: a test of the default interventionist account of belief bias.

PubMed

Handley, Simon J; Newstead, Stephen E; Trippas, Dries

2011-01-01

According to dual-process accounts of thinking, belief-based responses on reasoning tasks are generated as default but can be intervened upon in favor of logical responding, given sufficient time, effort, or cognitive resource. In this article, we present the results of 5 experiments in which participants were instructed to evaluate the conclusions of logical arguments on the basis of either their logical validity or their believability. Contrary to the predictions arising from these accounts, the logical status of the presented conclusion had a greater impact on judgments concerning its believability than did the believability of the conclusion on judgments about whether it followed logically. This finding was observed when instructional set was presented as a between-participants factor (Experiment 1), when instruction was indicated prior to problem presentation by a cue (Experiment 2), and when the cue appeared simultaneously with conclusion presentation (Experiments 3 and 4). The finding also extended to a range of simple and more complex argument forms (Experiment 5). In these latter experiments, belief-based judgments took significantly longer than those made under logical instructions. We discuss the implications of these findings for default interventionist accounts of belief bias.

Practice Effects on Story Memory and List Learning Tests in the Neuropsychological Assessment of Older Adults

PubMed Central

Gurnani, Ashita S.; Saurman, Jessica L.; Chapman, Kimberly R.; Steinberg, Eric G.; Martin, Brett; Chaisson, Christine E.; Mez, Jesse; Tripodis, Yorghos; Stern, Robert A.

2016-01-01

Two of the most commonly used methods to assess memory functioning in studies of cognitive aging and dementia are story memory and list learning tests. We hypothesized that the most commonly used story memory test, Wechsler's Logical Memory, would generate more pronounced practice effects than a well validated but less common list learning test, the Neuropsychological Assessment Battery (NAB) List Learning test. Two hundred eighty-seven older adults, ages 51 to 100 at baseline, completed both tests as part of a larger neuropsychological test battery on an annual basis. Up to five years of recall scores from participants who were diagnosed as cognitively normal (n = 96) or with mild cognitive impairment (MCI; n = 72) or Alzheimer's disease (AD; n = 121) at their most recent visit were analyzed with linear mixed effects regression to examine the interaction between the type of test and the number of times exposed to the test. Other variables, including age at baseline, sex, education, race, time (years) since baseline, and clinical diagnosis were also entered as fixed effects predictor variables. The results indicated that both tests produced significant practice effects in controls and MCI participants; in contrast, participants with AD declined or remained stable. However, for the delayed—but not the immediate—recall condition, Logical Memory generated more pronounced practice effects than NAB List Learning (b = 0.16, p < .01 for controls). These differential practice effects were moderated by clinical diagnosis, such that controls and MCI participants—but not participants with AD—improved more on Logical Memory delayed recall than on delayed NAB List Learning delayed recall over five annual assessments. Because the Logical Memory test is ubiquitous in cognitive aging and neurodegenerative disease research, its tendency to produce marked practice effects—especially on the delayed recall condition—suggests a threat to its validity as a measure of new learning, an essential construct for dementia diagnosis. PMID:27711147

Test-Enhanced E-Learning Strategies in Postgraduate Medical Education: A Randomized Cohort Study.

PubMed

DelSignore, Lisa A; Wolbrink, Traci A; Zurakowski, David; Burns, Jeffrey P

2016-11-21

The optimal design of pedagogical strategies for e-learning in graduate and postgraduate medical education remains to be determined. Video-based e-learning use is increasing, with initial research suggesting that taking short breaks while watching videos (independent of answering test questions) may improve learning by focusing attention on the content presented. Interspersed test questions may also improve knowledge acquisition and retention. To examine the effect of interspersed test questions and periodic breaks on immediate knowledge acquisition and retention at 6 months by pediatric residents engaged in video-based e-learning. First- and second-year pediatric residents were randomized to 1 of the following 3 groups: viewing the complete video uninterrupted (full video), viewing the video interrupted with unrelated logic puzzles (logic puzzles), or viewing the video interrupted with brief comprehension test questions (short answer questions). Residents answered pre- and post-tests before and after video viewing, followed by a retention test at 6 months. Primary outcome included comparison of the change in test scores between groups. A total of 49 residents completed the initial testing session. All 3 learning groups had comparable mean increases in immediate knowledge gain, but with no significant differences between groups (F 2,46 =0.35, P=.71). Thirty-five residents completed retention testing with comparable degrees of knowledge retention in the full video and short answer test questions groups (P<.001), but no significant change in the logic puzzles group (F 1,32 =2.44, P=.13). Improved knowledge gain was not demonstrated among residents answering interspersed questions or completing logic puzzles during interrupted online video viewing when compared with residents viewing uninterrupted video content. However, residents who either participated in uninterrupted video viewing or answered interspersed questions during interrupted video viewing demonstrated significant knowledge retention at 6 months. ©Lisa A DelSignore, Traci A Wolbrink, David Zurakowski, Jeffrey P Burns. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 21.11.2016.

Tensile testing method for rare earth based bulk superconductors at liquid nitrogen temperature

NASA Astrophysics Data System (ADS)

Kasaba, K.; Katagiri, K.; Murakami, A.; Sato, G.; Sato, T.; Murakami, M.; Sakai, N.; Teshima, H.; Sawamura, M.

2005-10-01

Bending tests have been commonly carried out to investigate the mechanical properties of melt-processed rare earth based bulk superconductors. Tensile tests by using small specimen, however, are preferable to evaluate the detailed distribution of the mechanical properties and the intrinsic elastic modulus because no stress distributions exist in the cross-section. In this study, the tensile test method at low temperature by using specimens with the dimensions of 3 × 3 × 4 mm from Y123 and Gd123 bulks was examined. They were glued to Al alloy rods at 400 K by using epoxy resin. Tests were carried out at liquid nitrogen temperature (LNT) by using the immersion type jig. Although the bending strength in the direction perpendicular to the c-axis of the bulks at LNT is higher than that at room temperature (RT), the tensile strength at LNT was lower than that at RT. Many of specimens fractured near the interface between the specimen and the Al alloy rod at LNT. According to the finite element method analysis, it was shown that there was a peak thermal stress in the loading direction near the interface and it was significantly higher at LNT than that at RT. It was also shown that the replacement of the Al alloy rod to Ti rod of which the coefficient of thermal expansion is close to that of bulks significantly increased the tensile strength.

SNS Heterojunctions With New Combinations Of Materials

NASA Technical Reports Server (NTRS)

Vasquez, Richard P.; Hunt, Brian D.; Foote, Marc C.

1992-01-01

New combinations of materials proposed for superconductor/normal-metal/superconductor (SNS) heterojunctions in low-temperature electronic devices such as fast switches, magnetometers, and mixers. Epitaxial heterojunctions formed between high-temperature superconductors and either oxide semiconductors or metals. Concept offers alternative to other three-layer heterojunction concepts; physical principles of operation permit SNS devices to have thicker barrier layers and fabricated more easily.

Optical Lattice Gases of Interacting Fermions

DTIC Science & Technology

2015-12-02

artificial gauge fields or spin-orbit coupling. This topological insulator phase turns into a topological superconductor featuring Majorana zero modes at... superconductors , are a prototypical topological superfluid. Despite its conceptually different origin, the state found by the research team for s-wave...release 2 external field [7]. A Weyl superconductor or superfluid is a gapless topological state of matter that features nontrivial (hedgehog

Depositing High-T(sub c) Superconductors On Normal-Conductor Wires

NASA Technical Reports Server (NTRS)

Kirlin, Peter S.

1994-01-01

Experiments have demonstrated feasibility of depositing thin layers of high-T(sub c) superconductor on normally electrically conductive wires. Superconductivity evident at and below critical temperature (T{sub c}) of 71 K. OMCVD, organometallic vapor deposition, apparatus coats Ag wire with layer high-T(sub c) superconductor. Superconductive phase of this material formed subsequently by annealing under controlled conditions.

Spectroscopy of Magnetic Excitations in Magnetic Superconductors Using Vortex Motion

NASA Astrophysics Data System (ADS)

Bulaevskii, L. N.; Hruška, M.; Maley, M. P.

2005-11-01

In magnetic superconductors a moving vortex lattice is accompanied by an ac magnetic field which leads to the generation of spin waves. At resonance conditions the dynamics of vortices in magnetic superconductors changes drastically, resulting in strong peaks in the dc I-V characteristics at voltages at which the washboard frequency of the vortex lattice matches the spin wave frequency ωs(g), where g are the reciprocal vortex lattice vectors. We show that if the washboard frequency lies above the magnetic gap, measurement of the I-V characteristics provides a new method to obtain information on the spectrum of magnetic excitations in borocarbides and cuprate layered magnetic superconductors.

Raman study of the Hg0.7Cr0.3Sr2CuO4+δ superconductors

NASA Astrophysics Data System (ADS)

Lee, S.-Y.; Chang, B.-Y.; Yang, I.-S.; Gwak, J.-H.; Kim, S.-J.; Choi, J.-H.; Lee, S.-I.; Yakhmi, J. V.; Mandal, J. B.; Bandyopadhyay, B.; Ghosh, B.

1997-08-01

The local environment of the apical oxygens (OA) in the Sr-substituted mercury-based superconductor Hg0.7Cr0.3Sr2CuO4+δ is investigated using Raman spectroscopy. Raman spectra from the Sr-substituted Hg-1201 samples show broad OA A1g double peaks at 553 and 583 cm-l, which are 10 - 20 cm-1 lower than the pristine Hg-1201. The existence of, and lower shift of, the double peaks in the Raman spectra of the Sr-substituted Hg-1201 superconductors indicate changes in the environment of OA in the Sr-substituted mercury-based superconductors.

Isotope effect on electron-phonon interaction in the multiband superconductor MgB 2

DOE PAGES

Mou, Daixiang; Manni, Soham; Taufour, Valentin; ...

2016-04-07

We investigate the effect of isotope substitution on the electron-phonon interaction in the multiband superconductor MgB 2 using tunable laser-based angle-resolved photoemission spectroscopy. The kink structure around 70 meV in the σ band, which is caused by electron coupling to the E 2g phonon mode, is shifted to higher binding energy by ~3.5 meV in Mg 10B 2 and the shift is not affected by superconducting transition. Furthermore, these results serve as the benchmark for investigations of isotope effects in known, unconventional superconductors and newly discovered superconductors where the origin of pairing is unknown.

Monolithic integrated high-T.sub.c superconductor-semiconductor structure

NASA Technical Reports Server (NTRS)

Barfknecht, Andrew T. (Inventor); Garcia, Graham A. (Inventor); Russell, Stephen D. (Inventor); Burns, Michael J. (Inventor); de la Houssaye, Paul R. (Inventor); Clayton, Stanley R. (Inventor)

2000-01-01

A method for the fabrication of active semiconductor and high-temperature superconducting device of the same substrate to form a monolithically integrated semiconductor-superconductor (MISS) structure is disclosed. A common insulating substrate, preferably sapphire or yttria-stabilized zirconia, is used for deposition of semiconductor and high-temperature superconductor substructures. Both substructures are capable of operation at a common temperature of at least 77 K. The separate semiconductor and superconductive regions may be electrically interconnected by normal metals, refractory metal silicides, or superconductors. Circuits and devices formed in the resulting MISS structures display operating characteristics which are equivalent to those of circuits and devices prepared on separate substrates.

Evaluation and Control of Mechanical Degradation of Austenitic Stainless 310S Steel Substrate During Coated Superconductor Processing

NASA Astrophysics Data System (ADS)

Kim, Seung-Gyu; Kim, Najung; Shim, Hyung-Seok; Kwon, Oh Min; Kwon, Dongil

2018-05-01

The superconductor industry considers cold-rolled austenitic stainless 310S steel a less expensive substitute for Hastelloy X as a substrate for coated superconductor. However, the mechanical properties of cold-rolled 310S substrate degrade significantly in the superconductor deposition process. To overcome this, we applied hot rolling at 900 °C (or 1000 °C) to the 310S substrate. To check the property changes, a simulated annealing condition equivalent to that used in manufacturing was determined and applied. The effects of the hot rolling on the substrate were evaluated by analyzing its physical properties and texture.

Fracture toughness for copper oxide superconductors

DOEpatents

Goretta, Kenneth C.; Kullberg, Marc L.

1993-01-01

An oxide-based strengthening and toughening agent, such as tetragonal Zro.sub.2 particles, has been added to copper oxide superconductors, such as superconducting YBa.sub.2 Cu.sub.3 O.sub.x (123) to improve its fracture toughness (K.sub.IC). A sol-gel coating which is non-reactive with the superconductor, such as Y.sub.2 BaCuO.sub.5 (211) on the ZrO.sub.2 particles minimized the deleterious reactions between the superconductor and the toughening agent dispersed therethrough. Addition of 20 mole percent ZrO.sub.2 coated with 211 yielded a 123 composite with a K.sub.IC of 4.5 MPa(m).sup.0.5.

Possible field-tuned superconductor-insulator transition in high-Tc superconductors: implications for pairing at high magnetic fields.

PubMed

Steiner, M A; Boebinger, G; Kapitulnik, A

2005-03-18

The behavior of some high temperature superconductors (HTSC), such as La(2-x)Sr(x)CuO(4) and Bi(2)Sr(2-x)La(x)CuO(6 + delta), at very high magnetic fields, is similar to that of thin films of amorphous InOx near the magnetic-field-tuned superconductor-insulator transition. Analyzing the InOx data at high fields in terms of persisting local pairing amplitude, we argue by analogy that the local pairing amplitude also persists well into the dissipative state of the HTSCs, the regime commonly denoted as the "normal state" in very high magnetic field experiments.

Frequency-dependent shot noise in long disordered superconductor-normal-metal-superconductor contacts.

PubMed

Nagaev, K E

2001-04-02

The shot noise in long diffusive superconductor-normal-metal-superconductor contacts is calculated using the semiclassical approach. At low frequencies and for purely elastic scattering, the voltage dependence of the noise is of the form S(I) = (4Delta+2eV)/3R. The electron-electron scattering suppresses the noise at small voltages resulting in vanishing noise yet infinite dS(I)/dV at V = 0. The distribution function of electrons consists of a series of steps, and the frequency dependence of noise exhibits peculiarities at omega = neV, omega = neV-2Delta, and omega = 2Delta-neV for integer n.

Engineering topological superconductors using surface atomic-layer/molecule hybrid materials

NASA Astrophysics Data System (ADS)

Uchihashi, Takashi

2015-08-01

Surface atomic-layer (SAL) superconductors consisting of epitaxially grown metal adatoms on a clean semiconductor surface have been recently established. Compared to conventional metal thin films, they have two important features: (i) space-inversion symmetry-breaking throughout the system and (ii) high sensitivity to surface adsorption of foreign species. These potentially lead to manifestation of the Rashba effect and a Zeeman field exerted by adsorbed magnetic organic molecules. After introduction of the archetypical SAL superconductor Si(111)-(√7 × √3)-In, we describe how these features are utilized to engineer a topological superconductor with Majorana fermions and discuss its promises and expected challenges.

Theory of quantum metal to superconductor transitions in highly conducting systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spivak, B.

2010-04-06

We derive the theory of the quantum (zero temperature) superconductor to metal transition in disordered materials when the resistance of the normal metal near criticality is small compared to the quantum of resistivity. This can occur most readily in situations in which 'Anderson's theorem' does not apply. We explicitly study the transition in superconductor-metal composites, in an swave superconducting film in the presence of a magnetic field, and in a low temperature disordered d-wave superconductor. Near the point of the transition, the distribution of the superconducting order parameter is highly inhomogeneous. To describe this situation we employ a procedure whichmore » is similar to that introduced by Mott for description of the temperature dependence of the variable range hopping conduction. As the system approaches the point of the transition from the metal to the superconductor, the conductivity of the system diverges, and the Wiedemann-Franz law is violated. In the case of d-wave (or other exotic) superconductors we predict the existence of (at least) two sequential transitions as a function of increasing disorder: a d-wave to s-wave, and then an s-wave to metal transition.« less

Odd-frequency pairing in superconducting heterostructures .

NASA Astrophysics Data System (ADS)

Golubov, A. A.; Tanaka, Y.; Yokoyama, T.; Asano, Y.

2007-03-01

We present a general theory of the proximity effect in junctions between unconventional superconductors and diffusive normal metals (DN) or ferromagnets (DF). We consider all possible symmetry classes in a superconductor allowed by the Pauli principle: even-frequency spin-singlet even-parity state, even-frequency spin-triplet odd-parity state, odd-frequency spin-triplet even-parity state and odd-frequency spin-singlet odd-parity state. For each of the above states, symmetry and spectral properties of the induced pair amplitude in the DN (DF) are determined. The cases of junctions with spin-singlet s- and d-wave superconductors and spin-triplet p-wave superconductors are adressed in detail. We discuss the interplay between the proximity effect and midgap Andreev bound states arising at interfaces in unconventional (d- or p-wave) junctions. The most striking property is the odd-frequency symmetry of the pairing amplitude induced in DN (DF) in contacts with p-wave superconductors. This leads to zero-energy singularity in the density of states and to anomalous screening of an external magnetic field. Peculiarities of Josephson effect in d- or p-wave junctions are discussed. Experiments are suggested to detect an order parameter symmetry using heterostructures with unconventional superconductors.

Microstructural control and superconducting properties of YBCO melt textured single crystals

NASA Astrophysics Data System (ADS)

Jongprateep, Oratai

The high temperature superconductor has great potential for practical applications such as superconducting energy storage systems. Since the levitation force, required specifically for these applications, largely depends on the critical current density and loop size of the superconducting current, large-sized single crystals with high critical current density are desired. To achieve the goal in fabricating YBa2Cu3O 7-delta (Y123) samples suitable for the applications, detailed and systematic studies are required to gain further understanding of the crystal growth and flux pinning mechanisms. This research is aimed at constituting a contribution to the knowledge base for the Y123 high temperature superconductor field by extending the study of processing conditions involved in controlling the microstructure of the Y123 superconductors for the enhancement of crystal growth and superconductor properties. Relations among processing parameters, microstructure, crystal growth, and critical current density of Y123 superconductors have been established. The experimental results reveal that low heating rate and short holding time can lead to refinement of Y2BaCuO5 (Y211) particles, which is strongly favorable to enhancement of the crystal growth and electrical properties of the Y123 superconductors. It was observed that relatively large Y123 crystals (17-22 mm in size) can be obtained with fine needle-shaped Y211 particles, processed with low heating rate and short holding time at the maximum temperatures. Additionally, the research also formulated a technique to fabricate Y123 superconductors with improved electrical properties required for the practical applications. By incorporating additives such as BaCeO3, BaSnO 3, Pt and Nd2O3 into Y123 superconductors, refinement of Y211 particles occurs. In addition, secondary phase particles with sizes in sub-micrometer and nanometer range can be formed in the Y123 superconductors. The interfaces between the Y123 matrix and these Y211 or secondary phase particles are believed to act as flux pinning sites and to enhance the critical current density (Jc) in the superconductor. The results showed that formation of secondary phase inclusions in Y123 by doping with BaCeO3, BaSnO 3, Pt or Nd2O3 result in enhancement of J c due to the effective flux pinning.

Nonlinear Aerodynamic Modeling From Flight Data Using Advanced Piloted Maneuvers and Fuzzy Logic

NASA Technical Reports Server (NTRS)

Brandon, Jay M.; Morelli, Eugene A.

2012-01-01

Results of the Aeronautics Research Mission Directorate Seedling Project Phase I research project entitled "Nonlinear Aerodynamics Modeling using Fuzzy Logic" are presented. Efficient and rapid flight test capabilities were developed for estimating highly nonlinear models of airplane aerodynamics over a large flight envelope. Results showed that the flight maneuvers developed, used in conjunction with the fuzzy-logic system identification algorithms, produced very good model fits of the data, with no model structure inputs required, for flight conditions ranging from cruise to departure and spin conditions.

Phase diagram of (Li(1-x)Fe(x))OHFeSe: a bridge between iron selenide and arsenide superconductors.

PubMed

Dong, Xiaoli; Zhou, Huaxue; Yang, Huaixin; Yuan, Jie; Jin, Kui; Zhou, Fang; Yuan, Dongna; Wei, Linlin; Li, Jianqi; Wang, Xinqiang; Zhang, Guangming; Zhao, Zhongxian

2015-01-14

Previous experimental results have shown important differences between iron selenide and arsenide superconductors which seem to suggest that the high-temperature superconductivity in these two subgroups of iron-based families may arise from different electronic ground states. Here we report the complete phase diagram of a newly synthesized superconducting (SC) system, (Li1-xFex)OHFeSe, with a structure similar to that of FeAs-based superconductors. In the non-SC samples, an antiferromagnetic (AFM) spin-density-wave (SDW) transition occurs at ∼127 K. This is the first example to demonstrate such an SDW phase in an FeSe-based superconductor system. Transmission electron microscopy shows that a well-known √5×√5 iron vacancy ordered state, resulting in an AFM order at ∼500 K in AyFe2-xSe2 (A = metal ions) superconductor systems, is absent in both non-SC and SC samples, but a unique superstructure with a modulation wave vector q = (1)/2(1,1,0), identical to that seen in the SC phase of KyFe2-xSe2, is dominant in the optimal SC sample (with an SC transition temperature Tc = 40 K). Hence, we conclude that the high-Tc superconductivity in (Li1-xFex)OHFeSe stems from the similarly weak AFM fluctuations as FeAs-based superconductors, suggesting a universal physical picture for both iron selenide and arsenide superconductors.

Magnetic Signals of High-Temperature Superconductor Bulk During the Levitation Force Measurement Process

NASA Astrophysics Data System (ADS)

Huang, Huan; Zheng, Jun; Qian, Nan; Che, Tong; Zheng, Botian; Jin, Liwei; Deng, Zigang

2017-05-01

In order to study the commonly neglected magnetic field information in the course of levitation force measurement process in a superconducting maglev system, a multipoint magnetic field measurement platform was employed to acquire magnetic signals of a bulk high-Tc superconductor on both the top and the bottom surface. Working conditions including field cooling (FC) and zero field cooling were investigated for these vertical down and up motions above a permanent magnet guideway performed on a HTS maglev measurement system. We have discussed the magnetic flux variation process based on the Bean model. A magnetic hysteresis effect similar to the levitation force hysteresis loop of the bulk superconductor was displayed and analyzed in this paper. What is more valuable, there exists some available magnetic flux on the top surface of the bulk superconductor, and the proportion is as high as 62.42% in the FC condition, which provides an experimental hint to design the superconductor bulk and the applied field for practical use in a more efficient way. In particular, this work reveals real-time magnetic flux variation of the bulk superconductor in the levitation application, which is the other important information in contrast to the macroscopic levitation and guidance force investigations in previous studies, and it enriches the existing research methods. The results are significant for understanding the magnetic characteristic of superconductors, and they can contribute to optimize the present HTS maglev system design.

Pairing States of Spin-3/2 Fermions: Symmetry-Enforced Topological Gap Functions

NASA Astrophysics Data System (ADS)

Venderbos, Jörn W. F.; Savary, Lucile; Ruhman, Jonathan; Lee, Patrick A.; Fu, Liang

2018-01-01

We study the topological properties of superconductors with paired j =3/2 quasiparticles. Higher spin Fermi surfaces can arise, for instance, in strongly spin-orbit coupled band-inverted semimetals. Examples include the Bi-based half-Heusler materials, which have recently been established as low-temperature and low-carrier density superconductors. Motivated by this experimental observation, we obtain a comprehensive symmetry-based classification of topological pairing states in systems with higher angular momentum Cooper pairing. Our study consists of two main parts. First, we develop the phenomenological theory of multicomponent (i.e., higher angular momentum) pairing by classifying the stationary points of the free energy within a Ginzburg-Landau framework. Based on the symmetry classification of stationary pairing states, we then derive the symmetry-imposed constraints on their gap structures. We find that, depending on the symmetry quantum numbers of the Cooper pairs, different types of topological pairing states can occur: fully gapped topological superconductors in class DIII, Dirac superconductors, and superconductors hosting Majorana fermions. Notably, we find a series of nematic fully gapped topological superconductors, as well as double- and triple-Dirac superconductors, with quadratic and cubic dispersion, respectively. Our approach, applied here to the case of j =3/2 Cooper pairing, is rooted in the symmetry properties of pairing states, and can therefore also be applied to other systems with higher angular momentum and high-spin pairing. We conclude by relating our results to experimentally accessible signatures in thermodynamic and dynamic probes.

Development of an experimental system for characterization of high-temperature superconductors cooled by liquid hydrogen under the external magnetic field

NASA Astrophysics Data System (ADS)

Tatsumoto, H.; Shirai, Y.; Shiotsu, M.; Naruo, Y.; Kobayashi, H.; Inatani, Y.

2014-05-01

An experimental system has been developed to investigate electro-magnetic properties of high-Tc superconductors cooled by liquid hydrogen under the external magnetic field of up to 7 T. A LH2 cryostat is concentrically mounted on the inside of a LHe cryostat to cool a NbTi superconducting magnet. The experimental system is installed in an explosion-proof room. Explosion proof electrical devices are used and current leads are covered with an enclosure filled with nitrogen gas. A remote control system has been developed. Furthermore, the effects of stray magnetic field on the existing and the new devices are investigated and electro-magnetic shielding panels and enclosure made of iron were designed. It is confirmed through the cryogenic test that the experimental system meets the design requirements.

A Low-noise Micromachined Millimeter-Wave Heterodyne Mixer using Nb Superconducting Tunnel Junctions

NASA Technical Reports Server (NTRS)

DeLange, Gert; Jacobson, Brian R.; Hu, Qing

1996-01-01

A heterodyne mixer with a micromachined horn antenna and a superconductor-insulator-superconductor (SIS) tunnel junction as mixing element is tested in the W-band (75-115 GHz) frequency range. Micromachined integrated horn antennas consist of a dipole antenna suspended on a thin Si3N4 dielectric membrane inside a pyramidal cavity etched in silicon. The mixer performance is optimized by using a backing plane behind the dipole antenna to tune out the capacitance of the tunnel junction. The lowest receiver noise temperature of 30 +/- 3 K (without any correction) is measured at 106 GHz with a 3-dB bandwidth of 8 GHz. This sensitivity is comparable to the state-of-the-art waveguide and quasi-optical SIS receivers, showing the potential use of micromachined horn antennas in imaging arrays.

Wideband fixed-tuned SIS receiver for 200-GHz operation

NASA Technical Reports Server (NTRS)

Blundell, Raymond; Tong, Cheuk-Yu E.; Papa, D. Cosmo; Leombruno, R. Louie; Zhang, Xiaolei; Paine, Scott; Stern, Jeffrey A.; Leduc, Henry G.; Bumble, Bruce

1995-01-01

We report on the design and development of a heterodyne receiver, designed to cover the frequency range 176-256 GHz. This receiver incorporates a niobium superconductor-insulator-superconductor (SIS) tunnel junction mixer, which, chiefly for reasons of reliability and ease of operation, is a fixed-tuned waveguide design. On-chip tuning is provided to resonate out the junction's geometric capacitance and produce a good match to the waveguide circuit. Laboratory measurements on the first test receiver indicate that the required input bandwidth (about 40%) is achieved with an average receiver noise temperature of below 50 K. Mixer conversion gain is observed at some frequencies, and the lowest measured receiver noise is less than 30 K. Furthermore, the SIS mixer used in this receiver is of simple construction, is easy to assemble and is therefore a good candidate for duplication.

Superconductivity. Observation of broken time-reversal symmetry in the heavy-fermion superconductor UPt₃.

PubMed

Schemm, E R; Gannon, W J; Wishne, C M; Halperin, W P; Kapitulnik, A

2014-07-11

Models of superconductivity in unconventional materials can be experimentally differentiated by the predictions they make for the symmetries of the superconducting order parameter. In the case of the heavy-fermion superconductor UPt3, a key question is whether its multiple superconducting phases preserve or break time-reversal symmetry (TRS). We tested for asymmetry in the phase shift between left and right circularly polarized light reflected from a single crystal of UPt3 at normal incidence and found that this so-called polar Kerr effect appears only below the lower of the two zero-field superconducting transition temperatures. Our results provide evidence for broken TRS in the low-temperature superconducting phase of UPt3, implying a complex two-component order parameter for superconductivity in this system. Copyright © 2014, American Association for the Advancement of Science.

Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

von Rohr, Fabian; Winiarski, Michał J.; Tao, Jing

High-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder. Here we show that the valence electron count dependence of the superconducting transition temperature in the high-entropy alloy falls between those of analogous simple solid solutions and amorphous materials and test the effect of alloy complexity on the superconductivity. We propose high-entropy alloys as excellentmore » intermediate systems for studying superconductivity as it evolves between crystalline and amorphous materials.« less

Frequency-tunable superconducting resonators via nonlinear kinetic inductance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vissers, M. R.; Hubmayr, J.; Sandberg, M.

2015-08-10

We have designed, fabricated, and tested a frequency-tunable high-Q superconducting resonator made from a niobium titanium nitride film. The frequency tunability is achieved by injecting a DC through a current-directing circuit into the nonlinear inductor whose kinetic inductance is current-dependent. We have demonstrated continuous tuning of the resonance frequency in a 180 MHz frequency range around 4.5 GHz while maintaining the high internal quality factor Q{sub i} > 180 000. This device may serve as a tunable filter and find applications in superconducting quantum computing and measurement. It also provides a useful tool to study the nonlinear response of a superconductor. In addition,more » it may be developed into techniques for measurement of the complex impedance of a superconductor at its transition temperature and for readout of transition-edge sensors.« less

Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor

PubMed Central

von Rohr, Fabian; Winiarski, Michał J.; Tao, Jing; Klimczuk, Tomasz; Cava, Robert Joseph

2016-01-01

High-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder. Here we show that the valence electron count dependence of the superconducting transition temperature in the high-entropy alloy falls between those of analogous simple solid solutions and amorphous materials and test the effect of alloy complexity on the superconductivity. We propose high-entropy alloys as excellent intermediate systems for studying superconductivity as it evolves between crystalline and amorphous materials. PMID:27803330

Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor

DOE PAGES

von Rohr, Fabian; Winiarski, Michał J.; Tao, Jing; ...

2016-11-01

High-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder. Here we show that the valence electron count dependence of the superconducting transition temperature in the high-entropy alloy falls between those of analogous simple solid solutions and amorphous materials and test the effect of alloy complexity on the superconductivity. We propose high-entropy alloys as excellentmore » intermediate systems for studying superconductivity as it evolves between crystalline and amorphous materials.« less

Airstart performance of a digital electronic engine control system on an F100 engine

NASA Technical Reports Server (NTRS)

Burcham, F. W., Jr.

1984-01-01

The digital electronic engine control (DEEC) system installed on an F100 engine in an F-15 aircraft was tested. The DEEC system incorporates a closed-loop air start feature in which the fuel flow is modulated to achieve the desired rate of compressor acceleration. With this logic the DEEC equipped F100 engine can achieve air starts over a larger envelope. The DEEC air start logic, the test program conducted on the F-15, and its results are described.

Fuzzy control of small servo motors

NASA Technical Reports Server (NTRS)

Maor, Ron; Jani, Yashvant

1993-01-01

To explore the benefits of fuzzy logic and understand the differences between the classical control methods and fuzzy control methods, the Togai InfraLogic applications engineering staff developed and implemented a motor control system for small servo motors. The motor assembly for testing the fuzzy and conventional controllers consist of servo motor RA13M and an encoder with a range of 4096 counts. An interface card was designed and fabricated to interface the motor assembly and encoder to an IBM PC. The fuzzy logic based motor controller was developed using the TILShell and Fuzzy C Development System on an IBM PC. A Proportional-Derivative (PD) type conventional controller was also developed and implemented in the IBM PC to compare the performance with the fuzzy controller. Test cases were defined to include step inputs of 90 and 180 degrees rotation, sine and square wave profiles in 5 to 20 hertz frequency range, as well as ramp inputs. In this paper we describe our approach to develop a fuzzy as well as PH controller, provide details of hardware set-up and test cases, and discuss the performance results. In comparison, the fuzzy logic based controller handles the non-linearities of the motor assembly very well and provides excellent control over a broad range of parameters. Fuzzy technology, as indicated by our results, possesses inherent adaptive features.

Statistical inference and Aristotle's Rhetoric.

PubMed

Macdonald, Ranald R

2004-11-01

Formal logic operates in a closed system where all the information relevant to any conclusion is present, whereas this is not the case when one reasons about events and states of the world. Pollard and Richardson drew attention to the fact that the reasoning behind statistical tests does not lead to logically justifiable conclusions. In this paper statistical inferences are defended not by logic but by the standards of everyday reasoning. Aristotle invented formal logic, but argued that people mostly get at the truth with the aid of enthymemes--incomplete syllogisms which include arguing from examples, analogies and signs. It is proposed that statistical tests work in the same way--in that they are based on examples, invoke the analogy of a model and use the size of the effect under test as a sign that the chance hypothesis is unlikely. Of existing theories of statistical inference only a weak version of Fisher's takes this into account. Aristotle anticipated Fisher by producing an argument of the form that there were too many cases in which an outcome went in a particular direction for that direction to be plausibly attributed to chance. We can therefore conclude that Aristotle would have approved of statistical inference and there is a good reason for calling this form of statistical inference classical.

Modelling default and likelihood reasoning as probabilistic reasoning

NASA Technical Reports Server (NTRS)

Buntine, Wray

1990-01-01

A probabilistic analysis of plausible reasoning about defaults and about likelihood is presented. Likely and by default are in fact treated as duals in the same sense as possibility and necessity. To model these four forms probabilistically, a qualitative default probabilistic (QDP) logic and its quantitative counterpart DP are derived that allow qualitative and corresponding quantitative reasoning. Consistency and consequent results for subsets of the logics are given that require at most a quadratic number of satisfiability tests in the underlying propositional logic. The quantitative logic shows how to track the propagation error inherent in these reasoning forms. The methodology and sound framework of the system highlights their approximate nature, the dualities, and the need for complementary reasoning about relevance.

Magnetic-field-controlled reconfigurable semiconductor logic.

PubMed

Joo, Sungjung; Kim, Taeyueb; Shin, Sang Hoon; Lim, Ju Young; Hong, Jinki; Song, Jin Dong; Chang, Joonyeon; Lee, Hyun-Woo; Rhie, Kungwon; Han, Suk Hee; Shin, Kyung-Ho; Johnson, Mark

2013-02-07

Logic devices based on magnetism show promise for increasing computational efficiency while decreasing consumed power. They offer zero quiescent power and yet combine novel functions such as programmable logic operation and non-volatile built-in memory. However, practical efforts to adapt a magnetic device to logic suffer from a low signal-to-noise ratio and other performance attributes that are not adequate for logic gates. Rather than exploiting magnetoresistive effects that result from spin-dependent transport of carriers, we have approached the development of a magnetic logic device in a different way: we use the phenomenon of large magnetoresistance found in non-magnetic semiconductors in high electric fields. Here we report a device showing a strong diode characteristic that is highly sensitive to both the sign and the magnitude of an external magnetic field, offering a reversible change between two different characteristic states by the application of a magnetic field. This feature results from magnetic control of carrier generation and recombination in an InSb p-n bilayer channel. Simple circuits combining such elementary devices are fabricated and tested, and Boolean logic functions including AND, OR, NAND and NOR are performed. They are programmed dynamically by external electric or magnetic signals, demonstrating magnetic-field-controlled semiconductor reconfigurable logic at room temperature. This magnetic technology permits a new kind of spintronic device, characterized as a current switch rather than a voltage switch, and provides a simple and compact platform for non-volatile reconfigurable logic devices.

Space qualified hybrid superconductor/semiconductor planar oscillator circuit

NASA Technical Reports Server (NTRS)

Miranda, F. A.; Chorey, C. M.; Romanofsky, R. R.; Bhasin, K. B.

1995-01-01

We report on the space qualification of a hybrid superconductor/semiconductor planar local oscillator (LO) at 8.4 GHz. This oscillator was designed, fabricated, and tested as a component for the High Temperature Superconductivity Space Experiment 2 (HTSSE-2). The LO consisted of a GaAs MESFET and microstrip circuitry patterned onto a YBa2Cu3O(7-delta) high temperature superconducting (HTS) thin film on a 1.0 x 1.0 sq cm lanthanum aluminate (LaAlO3) substrate. At 77 K, this oscillator achieved power output levels up to 10 dBm into a 50 Ohm load. When incorporated into a full cryogenic receiver, the LO provided output powers within 0.0-3.0 dBm with less than 50 mW of dc power dissipation. Space qualification data on the sensitivity of the HTS films to the processing steps involved in the fabrication of HTS-based components are presented. Data on ohmic contacts, strength of wire bonds made to such contacts, and aging effects as well as vibration test results are discussed.

Persistent-current switch for pancake coils of rare earth-barium-copper-oxide high-temperature superconductor: Design and test results of a double-pancake coil operated in liquid nitrogen (77–65 K) and in solid nitrogen (60–57 K)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qu, Timing; Michael, Philip C.; Bascuñán, Juan

2016-08-22

We present design and test results of a superconducting persistent current switch (PCS) for pancake coils of rare-earth-barium-copper-oxide, REBCO, high-temperature superconductor (HTS). Here, a REBCO double-pancake (DP) coil, 152-mm ID, 168-mm OD, 12-mm high, was wound with a no-insulation technique. We converted a ∼10-cm long section in the outermost layer of each pancake to a PCS. The DP coil was operated in liquid nitrogen (77–65 K) and in solid nitrogen (60–57 K). Over the operating temperature ranges of this experiment, the normal-state PCS enabled the DP coil to be energized; thereupon, the PCS resumed the superconducting state and the DP coil fieldmore » decayed with a time constant of 100 h, which would have been nearly infinite, i.e., persistent-mode operation, were the joint across the coil terminals superconducting.« less

Development of superconducting magnetic bearing using superconducting coil and bulk superconductor

NASA Astrophysics Data System (ADS)

Seino, H.; Nagashima, K.; Arai, Y.

2008-02-01

The authors conducted a study on superconducting magnetic bearing, which consists of superconducting rotor and stator to apply the flywheel energy-storage system for railways. In this study, high temperature bulk superconductor (HTS bulk) was combined with superconducting coils to increase the load capacity of the bearing. In the first step of the study, the thrust rolling bearing was selected for application by using liquid nitrogen cooled HTS bulk. 60mm-diameter HTS bulks and superconducting coil which generated a high gradient of magnetic field by cusp field were adopted as a rotor and a stator for superconducting magnetic bearing, respectively. The results of the static load test and the rotation test, creep of the electromagnetic forces caused by static flux penetration and AC loss due to eccentric rotation were decreased to the level without any problems in substantial use by using two HTS bulks. In the result of verification of static load capacity, levitation force (thrust load) of 8900N or more was supportable, and stable static load capacity was obtainable when weight of 460kg was levitated.

Conceptualizing Magnification and Scale: The Roles of Spatial Visualization and Logical Thinking

ERIC Educational Resources Information Center

Jones, M. Gail; Gardner, Grant; Taylor, Amy R.; Wiebe, Eric; Forrester, Jennifer

2011-01-01

This study explored factors that contribute to students' concepts of magnification and scale. Spatial visualization, logical thinking, and concepts of magnification and scale were measured for 46 middle school students. Scores on the "Zoom Assessment" (an assessment of knowledge of magnification and scale) were correlated with the "Test of Logical…

A Game Plan for Teaching Logic.

ERIC Educational Resources Information Center

Woloshin, Phyllis Lerman

An experiment using game-theory to teach a unit on "fallacies" in logic was conducted at Oakton Community College. One experimental and two control group lecture-style classes were taught by three teachers using the same text and final test. The experimental class, after an introductory segment presented in lecture style, were involved in a…

Program Theory Evaluation: Logic Analysis

ERIC Educational Resources Information Center

Brousselle, Astrid; Champagne, Francois

2011-01-01

Program theory evaluation, which has grown in use over the past 10 years, assesses whether a program is designed in such a way that it can achieve its intended outcomes. This article describes a particular type of program theory evaluation--logic analysis--that allows us to test the plausibility of a program's theory using scientific knowledge.…

The Relationships Among Logical and Spatial Skills and Understanding Genetics Concepts and Problems.

ERIC Educational Resources Information Center

Costello, Sandra Judith

The purpose of this study was to determine whether relationships occur among spatial skills, logical reasoning, and various genetic concepts. Twenty-one students enrolled in an undergraduate genetics course in a northern New Jersey institution completed a series of tests and tasks designed to measure flexibility of closure, visualization,…

In vitro corrosion behaviour and microhardness of high-copper amalgams with platinum and indium.

PubMed

Ilikli, B G; Aydin, A; Işimer, A; Alpaslan, G

1999-02-01

Samples prepared from Luxalloy, GS-80, Permite-C and Logic and polished after 24 h by traditional methods were stored in polypropylene tubes containing phosphate-buffered saline solutions (pH 3.5 and 6.5) and distilled water. The amounts of mercury, silver, tin, copper, zinc, platinum and indium in the test solutions were determined at the first, second, eighth, 52nd and 78th week by atomic absorption spectrometry. At the end of the eighth week the amalgam samples were removed from solutions and evaluated by Rockwell Super Scial Microhardness tester. Statistically significant low amounts of metal ions were measured for Permite-C containing indium and Logic containing platinum. The microhardness test results showed that there were statistically significant increases in the microhardness of Permite-C and Logic. As a result it was shown that the amalgam samples were affected from corrosion conditions to different degrees. Sample of the Logic group that was stored in distilled water, showed smoother surface properties than other amalgam samples containing high copper. However, it was observed that samples of Permite-C group had the smoothest surface properties.

Nanoscale Measurements of Magnetism & Spin Coherence in Semiconductors

DTIC Science & Technology

2015-12-17

superconductor created by magnetic defects. These energy-resolved studies are distinct from typical spin-selective measurements performed previously using...MacDonald, B. A. Bernevig, A. Yazdani. Observation of Majorana fermions in ferromagnetic atomic chains on a superconductor , Science, (10 2014): 602... superconductor , Physical Review B, (07 2013): 0. doi: 10.1103/PhysRevB.88.020407 TOTAL: 4 Number of Papers published in peer-reviewed journals

Forming YBa2Cu3O7-x Superconductors On Copper Substrates

NASA Technical Reports Server (NTRS)

Mackenzie, J. Devin; Young, Stanley G.

1991-01-01

Experimental process forms layer of high-critical-temperature ceramic superconductor YBa2Cu3O7-x on surface of copper substrate. Offers possible solution to problem of finishing ceramic superconductors to required final sizes and shapes (difficult problem because these materials brittle and cannot be machined or bent). Further research necessary to evaluate superconducting qualities of surface layers and optimize process.

Intrinsic Josephson effects in the magnetic superconductor RuSr2GdCu2O8.

PubMed

Nachtrab, T; Koelle, D; Kleiner, R; Bernhard, C; Lin, C T

2004-03-19

We have measured interlayer current transport in small-sized RuSr2GdCu2O8 single crystals. We find a clear intrinsic Josephson effect showing that the material acts as a natural superconductor-insulator-ferromagnet-insulator-superconductor superlattice. Thus far, we detected no unconventional behavior due to the magnetism of the RuO2 layers.

Computational and Theoretical Investigations of Strongly Correlated Fermions in Optical Lattices

DTIC Science & Technology

2013-08-29

and two-particle spectral functions across the disorder - driven superconductor - insulator transition". 22. Invited speaker, \\Fermions in Optical...energy gaps across the disorder - driven superconductor - insulator transition", October 7, 2010, Harvard. 27. Seminar on \\Probing Quantum Phases of...Perimeter Institute, November 14, 2011. 37. Seminar on \\Single and two-particle energy gaps across the disorder - driven superconductor - insulator transition

"It was an Emotional Baby": Previvors' Family Planning Decision-Making Styles about Hereditary Breast and Ovarian Cancer Risk.

PubMed

Dean, Marleah; Rauscher, Emily A

2017-12-01

Women who test positive for a BRCA genetic mutation are at an increased risk for developing hereditary breast and ovarian cancer and have a 50% chance of passing on their genetic mutation to their children. The purpose of this study was to investigate how women who test positive for a BRCA mutation but have not been diagnosed with cancer make decisions regarding family planning. Analysis of interviews with 20 women revealed they engage in logical and emotional decision-making styles. Although women want to be logical to reduce their hereditary cancer risk, emotions often complicate their decision-making. Women experience fear and worry about a future cancer diagnosis, yet also desire to create a family, particularly having children through natural conception. That is, women negotiate having preventative surgeries in a logical doctor-recommended timeframe but also organize those decisions around emotional desires of motherhood. Overall, this study demonstrates the complex decisions women who test positive for a BRCA mutation must make in regards to genetic testing timing, family planning, and overall quality of life.

The state of domestic affairs: Housework, gender and state-level institutional logics.

PubMed

Ruppanner, Leah; Maume, David J

2016-11-01

Multi-level cross-national research consistently shows individual housework arrangements are structured by broader contexts of equality. Across this body of research, the United States is treated as a single entity. Yet, individual-level housework time may vary by state-to-state differences in institutional market, family and legislative logics. To test these relationships, we pair individual-level data from the American Time Use Survey (2003-2012; aged 18 to 64 n = 106,190) with three state-level indices - female labor force empowerment, family traditionalism and state government liberalism. For market institutional logics, we find wives and husbands spend more but mothers less time in housework in states where women have more labor market power. For family logics, we find mothers spend more and husbands less time in housework in more traditional states. For legislative logics, we find women and husbands spend more time in housework in more liberal states. Our results highlight the importance of state-to-state institutional logics on individuals' housework time. Copyright © 2016 Elsevier Inc. All rights reserved.

The electronic properties of high (Tc) superconductors probed by positron annihilation

NASA Astrophysics Data System (ADS)

Sundar, C. S.; Bharathi, A.; Jean, Y. C.; Hinks, D. G.; Dabrowski, B.; Zheng, Y.; Mitchell, A. W.; Ho, J. C.; Howell, K. H.; Wachs, A. L.

1989-06-01

The discovery of superconductivity at 30 K in Ba(.6)K(.4) BiO3 has generated considerable excitement in view of the contrasting properties of the Ba-K-Bi-O system when compared to the well known Cu-O based high temperature superconductors. Positron annihilation spectroscopy, which is a sensitive local probe of the electronic and defect properties of a solid, was extensively applied in the study of Cu-O based superconductors. The results of positron lifetime as a function of temperature in Ba-K-Bi-O are presented and compared with the known results in the cuprate superconductors. Plausible reasons for the observed temperature dependence of positron lifetime are presented.

Vortex motion and flux-flow resistivity in dirty multiband superconductors

NASA Astrophysics Data System (ADS)

Silaev, Mihail; Vargunin, Artjom

2016-12-01

The conductivity of vortex lattices in multiband superconductors with high concentration of impurities is calculated based on microscopic kinetic theory at temperatures significantly smaller than the critical one. Both the limits of high and low fields are considered, when the magnetic induction is close to or much smaller than the critical field strength Hc 2, respectively. It is shown that in contrast to single-band superconductors, the resistive properties are not universal but depend on the pairing constants and ratios of diffusivities in different bands. The low-field magnetoresistance can strongly exceed the Bardeen-Stephen estimation in a quantitative agreement with experimental data for the two-band superconductor MgB2.

A Brief Review of Recent Superconductivity Research at NIST

PubMed Central

Lundy, D. R.; Swartzendruber, L. J.; Bennett, L. H.

1989-01-01

A brief overview of recent superconductivity research at NIST is presented. Emphasis is placed on the new high-temperature oxide superconductors, though mention is made of important work on low-temperature superconductors, and a few historical notes are included. NIST research covers a wide range of interests. For the new high-temperature superconductors, research activities include determination of physical properties such as elastic constants and electronic structure, development of new techniques such as magnetic-field modulated microwave-absorption and determination of phase diagrams and crystal structure. For the low-temperature superconductors, research spans studying the effect of stress on current density to the fabrication of a new Josephson junction voltage standard. PMID:28053408

Impurity-induced states in superconducting heterostructures

NASA Astrophysics Data System (ADS)

Liu, Dong E.; Rossi, Enrico; Lutchyn, Roman M.

2018-04-01

Heterostructures allow the realization of electronic states that are difficult to obtain in isolated uniform systems. Exemplary is the case of quasi-one-dimensional heterostructures formed by a superconductor and a semiconductor with spin-orbit coupling in which Majorana zero-energy modes can be realized. We study the effect of a single impurity on the energy spectrum of superconducting heterostructures. We find that the coupling between the superconductor and the semiconductor can strongly affect the impurity-induced states and may induce additional subgap bound states that are not present in isolated uniform superconductors. For the case of quasi-one-dimensional superconductor/semiconductor heterostructures we obtain the conditions for which the low-energy impurity-induced bound states appear.

Contact spectroscopy of high-temperature superconductors (Review). I - Physical and methodological principles of the contact spectroscopy of high-temperature superconductors. Experimental results for La(2-x)Sr(x)CuO4 and their discussion

NASA Astrophysics Data System (ADS)

Ianson, I. K.

1991-03-01

Research in the field of high-temperature superconductors based on methods of tunneling and microcontact spectroscopy is reviewed in a systematic manner. The theoretical principles of the methods are presented, and various types of contacts are described and classified. Attention is given to deviations of the measured volt-ampere characteristics from those predicted by simple theoretical models and those observed for conventional superconductors. Results of measurements of the energy gap and fine structure of volt ampere characteristic derivatives are presented for La(2-x)Sr(x)CuO4.

A new method for measuring low resistivity contacts between silver and YBa2Cu3O(7-x) superconductor

NASA Technical Reports Server (NTRS)

Hsi, Chi-Shiung; Haertling, Gene H.; Sherrill, Max D.

1991-01-01

Several methods of measuring contact resistivity between silver electrodes and YBa2Cu3O(7-x) superconductors were investigated; including the two-point, the three point, and the lap-joint methods. The lap-joint method was found to yield the most consistent and reliable results and is proposed as a new technique for this measurement. Painting, embedding, and melting methods were used to apply the electrodes to the superconductor. Silver electrodes produced good ohmic contacts to YBa2Cu3O(7-x) superconductors with contact resistivities as low as 1.9 x 10 to the -9th ohm sq cm.

Mean-field description of topological charge 4e superconductors

NASA Astrophysics Data System (ADS)

Gabriele, Victoria; Luo, Jing; Teo, Jeffrey C. Y.

BCS superconductors can be understood by a mean-field approximation of two-body interacting Hamiltonians, whose ground states break charge conservation spontaneously by allowing non-vanishing expectation values of charge 2e Cooper pairs. Topological superconductors, such as one-dimensional p-wave wires, have non-trivial ground states that support robust gapless boundary excitations. We construct a four-body Hamiltonian in one dimension and perform a mean-field analysis. The mean-field Hamiltonian is now quartic in fermions but is still exactly solvable. The ground state exhibits 4-fermion expectation values instead of Cooper pair ones. There also exists a topological phase, where the charge 4e superconductor carries exotic zero energy boundary excitations.

Materials design for new superconductors

DOE PAGES

Norman, M. R.

2016-05-23

Since the announcement in 2011 of the Materials Genome Initiative by the Obama administration, much attention has been given to the subject of materials design to accelerate the discovery of new materials that could have technological implications. Although having its biggest impact for more applied materials like batteries, there is increasing interest in applying these ideas to predict new superconductors. This is obviously a challenge, given that superconductivity is a many body phenomenon, with whole classes of known superconductors lacking a quantitative theory. Given this caveat, various efforts to formulate materials design principles for superconductors are reviewed in this paper,more » with a focus on surveying the periodic table in an attempt to identify cuprate analogues.« less

Fracture toughness for copper oxide superconductors

DOEpatents

Goretta, K.C.; Kullberg, M.L.

1993-04-13

An oxide-based strengthening and toughening agent, such as tetragonal ZrO[sub 2] particles, has been added to copper oxide superconductors, such as superconducting YBa[sub 2]Cu[sub 3]O[sub x] (123) to improve its fracture toughness (K[sub IC]). A sol-gel coating which is non-reactive with the superconductor, such as Y[sub 2]BaCuO[sub 5] (211) on the ZrO[sub 2] particles minimized the deleterious reactions between the superconductor and the toughening agent dispersed therethrough. Addition of 20 mole percent ZrO[sub 2] coated with 211 yielded a 123 composite with a K[sub IC] of 4.5 MPa(m)[sup 0.5].

The geometric field (gravity) as an electro-chemical potential in a Ginzburg-Landau theory of superconductivity

NASA Astrophysics Data System (ADS)

Atanasov, Victor

2017-07-01

We extend the superconductor's free energy to include an interaction of the order parameter with the curvature of space-time. This interaction leads to geometry dependent coherence length and Ginzburg-Landau parameter which suggests that the curvature of space-time can change the superconductor's type. The curvature of space-time doesn't affect the ideal diamagnetism of the superconductor but acts as chemical potential. In a particular circumstance, the geometric field becomes order-parameter dependent, therefore the superconductor's order parameter dynamics affects the curvature of space-time and electrical or internal quantum mechanical energy can be channelled into the curvature of space-time. Experimental consequences are discussed.

Problems of the theory of superconductivity which involve spatial inhomogeneity

NASA Astrophysics Data System (ADS)

Svidzinskii, A. V.

This book is concerned with questions which are related to equilibrium phenomena in superconductors, giving particular attention to effects determined by a spatial variation of the order parameter. The microscopic theory of superconductivity is developed on the basis of a model which takes into account the direct interaction between electrons. The theory of current relations in superconductors is discussed, taking into consideration the magnetic properties of superconductors in weak fields and the Meissner effect. Aspects regarding the general theory of tunneling are also explored, including the Josephson effect. An investigation is conducted of the theory of current conditions in areas in which the superconductor is in contact with normally conducting metal.

Method for making a monolithic integrated high-T.sub.c superconductor-semiconductor structure

NASA Technical Reports Server (NTRS)

Burns, Michael J. (Inventor); de la Houssaye, Paul R. (Inventor); Russell, Stephen D. (Inventor); Garcia, Graham A. (Inventor); Barfknecht, Andrew T. (Inventor); Clayton, Stanley R. (Inventor)

2000-01-01

A method for the fabrication of active semiconductor and high-temperature perconducting devices on the same substrate to form a monolithically integrated semiconductor-superconductor (MISS) structure is disclosed. A common insulating substrate, preferably sapphire or yttria-stabilized zirconia, is used for deposition of semiconductor and high-temperature superconductor substructures. Both substructures are capable of operation at a common temperature of at least 77 K. The separate semiconductor and superconductive regions may be electrically interconnected by normal metals, refractory metal silicides, or superconductors. Circuits and devices formed in the resulting MISS structures display operating characteristics which are equivalent to those of circuits and devices prepared on separate substrates.

Engineering one-dimensional topological phases on p -wave superconductors

NASA Astrophysics Data System (ADS)

Sahlberg, Isac; Westström, Alex; Pöyhönen, Kim; Ojanen, Teemu

2017-05-01

In this paper, we study how, with the aid of impurity engineering, two-dimensional p -wave superconductors can be employed as a platform for one-dimensional topological phases. We discover that, while chiral and helical parent states themselves are topologically nontrivial, a chain of scalar impurities on both systems supports multiple topological phases and Majorana end states. We develop an approach which allows us to extract the topological invariants and subgap spectrum, even away from the center of the gap, for the representative cases of spinless, chiral, and helical superconductors. We find that the magnitude of the topological gaps protecting the nontrivial phases may be a significant fraction of the gap of the underlying superconductor.

The superconducting state parameters of glassy superconductors

NASA Astrophysics Data System (ADS)

Vora, Aditya M.

2011-11-01

We present theoretical investigations of the superconducting state parameters (SSPs), i.e. the electron-phonon coupling strength, λ, Coulomb pseudopotential, μ*, transition temperature, Tc, isotope effect exponent, α, and effective interaction strength, N0V, of glassy superconductors by employing Ashcroft's well know empty core model potential for the first time using five screening functions proposed by Hartree (H), Taylor, Ichimaru-Utsumi (IU), Farid et al and Sarkar et al. The Tc obtained from the H and IU screening functions is found to be in excellent agreement with available experimental data. Also, the present results confirm the superconducting phase in bulk metallic glass superconductors. A strong dependency of the SSPs of the glassy superconductors on the 'Z' valence is found.

Hall viscosity of a chiral two-orbital superconductor at finite temperatures

NASA Astrophysics Data System (ADS)

Yazdani-Hamid, Meghdad; Shahzamanian, Mohammad Ali

2018-06-01

The Hall viscosity known as the anti-symmetric part of the viscosity fourth-rank tensor. Such dissipationless response which appears for systems with broken time reversal symmetry. We calculate this non-dissipative quantity for a chiral two-orbital superconductor placed in a viscoelastic magnetic field using the linear response theory and apply our calculations to the putative multiband chiral superconductor Sr2RuO4. The chirality origin of a multiband superconductor arises from the interorbital coupling of the superconducting state. This feature leads to the robustness of the Hall viscosity against temperature and impurity effects. We study the temperature effect on the Hall viscosity at the one-loop approximation.

Observation of conductance doubling in an Andreev quantum point contact

NASA Astrophysics Data System (ADS)

Kjaergaard, M.; Nichele, F.; Suominen, H.; Nowak, M.; Wimmer, M.; Akhmerov, A.; Folk, J.; Flensberg, K.; Shabani, J.; Palmstrom, C.; Marcus, C.

One route to study the non-Abelian nature of excitations in topological superconductors is to realise gateable two dimensional (2D) semiconducting systems, with spin-orbit coupling in proximity to an s-wave superconductor. Previous work on coupling 2D electron gases (2DEG) with superconductors has been hindered by a non-ideal interface and unstable gateability. We report measurements on a gateable 2DEG coupled to superconductors through a pristine interface, and use aluminum grown in situ epitaxially on an InGaAs/InAs electron gas. We demonstrate quantization in units of 4e2 / h in a quantum point contact (QPC) in such hybrid systems. Operating the QPC as a tunnel probe, we observe a hard superconducting gap, overcoming the soft-gap problem in 2D superconductor/semiconductor systems. Our work paves way for a new and highly scalable system in which to pursue topological quantum information processing. Research supported by Microsoft Project Q and the Danish National Research Foundation.

Higher-order topological insulators and superconductors protected by inversion symmetry

NASA Astrophysics Data System (ADS)

Khalaf, Eslam

2018-05-01

We study surface states of topological crystalline insulators and superconductors protected by inversion symmetry. These fall into the category of "higher-order" topological insulators and superconductors which possess surface states that propagate along one-dimensional curves (hinges) or are localized at some points (corners) on the surface. We provide a complete classification of inversion-protected higher-order topological insulators and superconductors in any spatial dimension for the 10 symmetry classes by means of a layer construction. We discuss possible physical realizations of such states starting with a time-reversal-invariant topological insulator (class AII) in three dimensions or a time-reversal-invariant topological superconductor (class DIII) in two or three dimensions. The former exhibits one-dimensional chiral or helical modes propagating along opposite edges, whereas the latter hosts Majorana zero modes localized to two opposite corners. Being protected by inversion, such states are not pinned to a specific pair of edges or corners, thus offering the possibility of controlling their location by applying inversion-symmetric perturbations such as magnetic field.

Quantized conductance doubling and hard gap in a two-dimensional semiconductor-superconductor heterostructure.

PubMed

Kjaergaard, M; Nichele, F; Suominen, H J; Nowak, M P; Wimmer, M; Akhmerov, A R; Folk, J A; Flensberg, K; Shabani, J; Palmstrøm, C J; Marcus, C M

2016-09-29

Coupling a two-dimensional (2D) semiconductor heterostructure to a superconductor opens new research and technology opportunities, including fundamental problems in mesoscopic superconductivity, scalable superconducting electronics, and new topological states of matter. One route towards topological matter is by coupling a 2D electron gas with strong spin-orbit interaction to an s-wave superconductor. Previous efforts along these lines have been adversely affected by interface disorder and unstable gating. Here we show measurements on a gateable InGaAs/InAs 2DEG with patterned epitaxial Al, yielding devices with atomically pristine interfaces between semiconductor and superconductor. Using surface gates to form a quantum point contact (QPC), we find a hard superconducting gap in the tunnelling regime. When the QPC is in the open regime, we observe a first conductance plateau at 4e 2 /h, consistent with theory. The hard-gap semiconductor-superconductor system demonstrated here is amenable to top-down processing and provides a new avenue towards low-dissipation electronics and topological quantum systems.

Electronic origin of high-temperature superconductivity in single-layer FeSe superconductor.

PubMed

Liu, Defa; Zhang, Wenhao; Mou, Daixiang; He, Junfeng; Ou, Yun-Bo; Wang, Qing-Yan; Li, Zhi; Wang, Lili; Zhao, Lin; He, Shaolong; Peng, Yingying; Liu, Xu; Chen, Chaoyu; Yu, Li; Liu, Guodong; Dong, Xiaoli; Zhang, Jun; Chen, Chuangtian; Xu, Zuyan; Hu, Jiangping; Chen, Xi; Ma, Xucun; Xue, Qikun; Zhou, X J

2012-07-03

The recent discovery of high-temperature superconductivity in iron-based compounds has attracted much attention. How to further increase the superconducting transition temperature (T(c)) and how to understand the superconductivity mechanism are two prominent issues facing the current study of iron-based superconductors. The latest report of high-T(c) superconductivity in a single-layer FeSe is therefore both surprising and significant. Here we present investigations of the electronic structure and superconducting gap of the single-layer FeSe superconductor. Its Fermi surface is distinct from other iron-based superconductors, consisting only of electron-like pockets near the zone corner without indication of any Fermi surface around the zone centre. Nearly isotropic superconducting gap is observed in this strictly two-dimensional system. The temperature dependence of the superconducting gap gives a transition temperature T(c)~ 55 K. These results have established a clear case that such a simple electronic structure is compatible with high-T(c) superconductivity in iron-based superconductors.

Recent Advances in Layered Metal Chalcogenides as Superconductors and Thermoelectric Materials: Fe-Based and Bi-Based Chalcogenides.

PubMed

Mizuguchi, Yoshikazu

2016-04-01

Recent advances in layered (Fe-based and Bi-based) chalcogenides as superconductors or functional materials are reviewed. The Fe-chalcogenide (FeCh) family are the simplest Fe-based high-Tc superconductors. The superconductivity in the FeCh family is sensitive to external or chemical pressure, and high Tc is attained when the local structure (anion height) is optimized. The Bi-chalcogenide (BiCh2) family are a new group of layered superconductors with a wide variety of stacking structures. Their physical properties are also sensitive to external or chemical pressure. Recently, we revealed that the emergence of superconductivity and the Tc in this family correlate with the in-plane chemical pressure. Since the flexibility of crystal structure and electronic states are an advantage of the BiCh2 family for designing functionalities, I briefly review recent developments in this family as not only superconductors but also other functional materials. © 2016 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Emergent loop-nodal s(±)-wave superconductivity in CeCu(2)Si(2): similarities to the iron-based superconductors.

PubMed

Ikeda, Hiroaki; Suzuki, Michi-To; Arita, Ryotaro

2015-04-10

Heavy-fermion superconductors are prime candidates for novel electron-pairing states due to the spin-orbital coupled degrees of freedom and electron correlations. Superconductivity in CeCu_{2}Si_{2} discovered in 1979, which is a prototype of unconventional (non-BCS) superconductors in strongly correlated electron systems, still remains unsolved. Here we provide the first report of superconductivity based on the advanced first-principles theoretical approach. We find that the promising candidate is an s_{±}-wave state with loop-shaped nodes on the Fermi surface, different from the widely expected line-nodal d-wave state. The dominant pairing glue is magnetic but high-rank octupole fluctuations. This system shares the importance of multiorbital degrees of freedom with the iron-based superconductors. Our findings reveal not only the long-standing puzzle in this material, but also urge us to reconsider the pairing states and mechanisms in all heavy-fermion superconductors.

Identifying the genes of unconventional high temperature superconductors.

PubMed

Hu, Jiangping

We elucidate a recently emergent framework in unifying the two families of high temperature (high [Formula: see text]) superconductors, cuprates and iron-based superconductors. The unification suggests that the latter is simply the counterpart of the former to realize robust extended s-wave pairing symmetries in a square lattice. The unification identifies that the key ingredients (gene) of high [Formula: see text] superconductors is a quasi two dimensional electronic environment in which the d -orbitals of cations that participate in strong in-plane couplings to the p -orbitals of anions are isolated near Fermi energy. With this gene, the superexchange magnetic interactions mediated by anions could maximize their contributions to superconductivity. Creating the gene requires special arrangements between local electronic structures and crystal lattice structures. The speciality explains why high [Formula: see text] superconductors are so rare. An explicit prediction is made to realize high [Formula: see text] superconductivity in Co/Ni-based materials with a quasi two dimensional hexagonal lattice structure formed by trigonal bipyramidal complexes.

Preparation of superconductor precursor powders

DOEpatents

Bhattacharya, Raghunath; Blaugher, Richard D.

1995-01-01

A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals, such as nitrate salts of thallium, barium, calcium, and copper, which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of thallium in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products.

Theoretical modeling of critical temperature increase in metamaterial superconductors

NASA Astrophysics Data System (ADS)

Smolyaninov, Igor; Smolyaninova, Vera

Recent experiments have demonstrated that the metamaterial approach is capable of drastic increase of the critical temperature Tc of epsilon near zero (ENZ) metamaterial superconductors. For example, tripling of the critical temperature has been observed in Al-Al2O3 ENZ core-shell metamaterials. Here, we perform theoretical modelling of Tc increase in metamaterial superconductors based on the Maxwell-Garnett approximation of their dielectric response function. Good agreement is demonstrated between theoretical modelling and experimental results in both aluminum and tin-based metamaterials. Taking advantage of the demonstrated success of this model, the critical temperature of hypothetic niobium, MgB2 and H2S-based metamaterial superconductors is evaluated. The MgB2-based metamaterial superconductors are projected to reach the liquid nitrogen temperature range. In the case of an H2S-based metamaterial Tc appears to reach 250 K. This work was supported in part by NSF Grant DMR-1104676 and the School of Emerging Technologies at Towson University.

Effect of Te doping on FeSe superconductor synthesized by powder-in-tube

NASA Astrophysics Data System (ADS)

Imaduddin, A.; Nisa, K.; Yudanto, S. D.; Nugraha, H.; Siswayanti, B.

2017-04-01

FeSe is a superconducting material, which has the simplest crystal structure among the Fe-based superconductors. It has no arsenic element, which is very harmful to the human body. In this study, we analyzed the effects of milling time and Te doping on FeSe superconductors. The synthesis of the samples were carried out using powder-in-tube method in a SS304 stainless steel tube. After the pressing process, followed by the sintering process at 500° C for 20 hours, the samples were removed from the tubes. Later, we analyzed its crystal structures, surfaces morphology and the superconductivity properties. Δ-FeSe phase (hexagonal, non-superconductor) and β-FeSe (tetragonal, superconductor) were formed in the samples, including minor phases of Fe and Fe3Se4. Te doping changed the crystal structure from β-FeSe and Δ-FeSe into FeSe0.5Te0.5. In addition, the onset critical temperature (TC, onset) shifted to higher temperature.

Hybrid crystals of cuprates and iron-based superconductors

NASA Astrophysics Data System (ADS)

Xia, Dai; Cong-Cong, Le; Xian-Xin, Wu; Jiang-Ping, Hu

2016-07-01

We propose two possible new compounds, Ba2CuO2Fe2As2 and K2CuO2Fe2Se2, which hybridize the building blocks of two high temperature superconductors, cuprates and iron-based superconductors. These compounds consist of square CuO2 layers and antifluorite-type Fe2 X 2 (X = As, Se) layers separated by Ba/K. The calculations of binding energies and phonon spectra indicate that they are dynamically stable, which ensures that they may be experimentally synthesized. The Fermi surfaces and electronic structures of the two compounds inherit the characteristics of both cuprates and iron-based superconductors. These compounds can be superconductors with intriguing physical properties to help to determine the pairing mechanisms of high T c superconductivity. Project supported by the National Basic Research Program of China (Grant No. 2015CB921300), the National Natural Science Foundation of China (Grant Nos. 1190020 and 11334012), and the Strategic Priority Research Program of Chinese Academy of Sciences (Grant No. XDB07000000).

Quantized conductance doubling and hard gap in a two-dimensional semiconductor–superconductor heterostructure

PubMed Central

Kjaergaard, M.; Nichele, F.; Suominen, H. J.; Nowak, M. P.; Wimmer, M.; Akhmerov, A. R.; Folk, J. A.; Flensberg, K.; Shabani, J.; Palmstrøm, C. J.; Marcus, C. M.

2016-01-01

Coupling a two-dimensional (2D) semiconductor heterostructure to a superconductor opens new research and technology opportunities, including fundamental problems in mesoscopic superconductivity, scalable superconducting electronics, and new topological states of matter. One route towards topological matter is by coupling a 2D electron gas with strong spin–orbit interaction to an s-wave superconductor. Previous efforts along these lines have been adversely affected by interface disorder and unstable gating. Here we show measurements on a gateable InGaAs/InAs 2DEG with patterned epitaxial Al, yielding devices with atomically pristine interfaces between semiconductor and superconductor. Using surface gates to form a quantum point contact (QPC), we find a hard superconducting gap in the tunnelling regime. When the QPC is in the open regime, we observe a first conductance plateau at 4e2/h, consistent with theory. The hard-gap semiconductor–superconductor system demonstrated here is amenable to top-down processing and provides a new avenue towards low-dissipation electronics and topological quantum systems. PMID:27682268

Holographic superconductors in Einstein-æther gravity

NASA Astrophysics Data System (ADS)

Lin, Kai; Wu, Yumei

2017-11-01

In this paper, we apply Anti-de Sitter (AdS) black hole solution of the Einstein-æther theory to the study of the holographic superconductor and show that the AdS black hole solution can be rewritten in some very simple forms, from which it is easy to identify the locations of various killing horizons. Then, we investigate the different effects of these horizons on the holographic superconductor.

Competing Quantum Orderings in Cuprate Superconductors:

NASA Astrophysics Data System (ADS)

Martin, I.; Ortiz, G.; Balatsky, A. V.; Bishop, A. R.

We present a minimal model for cuprate superconductors. At the unrestricted mean-field level, the model produces homogeneous superconductivity at large doping, striped superconductivity in the underdoped regime and various antiferromagnetic phases at low doping and for high temperatures. On the underdoped side, the superconductor is intrinsically inhomogeneous and global phase coherence is achieved through Josephson-like coupling of the superconducting stripes. The model is applied to calculate experimentally measurable ARPES spectra.

Interplay of Phonon and Exciton-Mediated Superconductivity in Hybrid Semiconductor-Superconductor Structures.

PubMed

Skopelitis, Petros; Cherotchenko, Evgenia D; Kavokin, Alexey V; Posazhennikova, Anna

2018-03-09

We predict a strong enhancement of the critical temperature in a conventional Bardeen-Cooper-Schrieffer (BCS) superconductor in the presence of a bosonic condensate of exciton polaritons. The effect depends strongly on the ratio of the cutoff frequencies for phonon and exciton-polariton mediated BCS superconductivity, respectively. We also discuss a possible design of hybrid semiconductor-superconductor structures suitable for the experimental observation of such an effect.

Investigation of the Feasibility of a Superconducting Self-Healing DC Grid on a LNG Carrier

DTIC Science & Technology

2015-06-21

art in High Temperature Superconductor technology is reviewed and an analytical approach of Superconducting DC Power Distribution on a power... Superconductors . I. INTRODUCTION During recent years, the usage of electrical power on- board vessels has grown exponentially. This fact, led...grid. When carrying DC current superconductors are perfectly lossless regardless of the cable length and the power rating of the line [1]. Also

Tailoring the Crystal Structure Toward Optimal Super Conductors

DTIC Science & Technology

2016-06-23

AFRL-AFOSR-VA-TR-2016-0210 TAILORING THE CRYSTAL STRUCTURE TOWARD OPTIMAL SUPERCONDUCTORS Emilia Morosan WILLIAM MARSH RICE UNIV HOUSTON TX Final...TAILORING THE CRYSTAL STRUCTURE TOWARD OPTIMAL SUPERCONDUCTORS 5a. CONTRACT NUMBER FA9550-11-1-0023 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...studied the properties of layered transition metal compounds in search of unconventional superconductors . The aim is to identify ground states competing

Advanced Fabrication Processes for Superconducting Very Large Scale Integrated Circuits

DTIC Science & Technology

2015-10-13

transistors. There are several reasons for this gigantic disparity: insufficient funding and lack of profit-driven investments in superconductor ...Inductance of circuit structures for MIT LL superconductor electronics fabrication process with 8 niobium layers,” IEEE Trans. Appl. Supercond., vol...vol. 25, No. 3, 1301704, June 2015. [7] V. Ambegaokar and A. Baratoff, “Tunneling between superconductors ,” Phys. Rev. Lett., vol. 10, no. 11, pp

Interplay of Phonon and Exciton-Mediated Superconductivity in Hybrid Semiconductor-Superconductor Structures

NASA Astrophysics Data System (ADS)

Skopelitis, Petros; Cherotchenko, Evgenia D.; Kavokin, Alexey V.; Posazhennikova, Anna

2018-03-01

We predict a strong enhancement of the critical temperature in a conventional Bardeen-Cooper-Schrieffer (BCS) superconductor in the presence of a bosonic condensate of exciton polaritons. The effect depends strongly on the ratio of the cutoff frequencies for phonon and exciton-polariton mediated BCS superconductivity, respectively. We also discuss a possible design of hybrid semiconductor-superconductor structures suitable for the experimental observation of such an effect.

Probing Electronic States of Magnetic Semiconductors Using Atomic Scale Microscopy & Spectroscopy

DTIC Science & Technology

2013-12-01

the metal- insulator transition, a feature that has long been predicted theoretically. We showed that a similar picture is at play in magnetic doping of... magnetic atoms on the surface of a superconductor can be used as a versatile platform for creating a topological superconductor . These initial...topological superconductivity and Majorana fermions in a chain of magnetic atoms on the surface of a superconductor Students and postdocs supported

Quantum interference in an interfacial superconductor.

PubMed

Goswami, Srijit; Mulazimoglu, Emre; Monteiro, Ana M R V L; Wölbing, Roman; Koelle, Dieter; Kleiner, Reinhold; Blanter, Ya M; Vandersypen, Lieven M K; Caviglia, Andrea D

2016-10-01

The two-dimensional superconductor that forms at the interface between the complex oxides lanthanum aluminate (LAO) and strontium titanate (STO) has several intriguing properties that set it apart from conventional superconductors. Most notably, an electric field can be used to tune its critical temperature (T c ; ref. 7), revealing a dome-shaped phase diagram reminiscent of high-T c superconductors. So far, experiments with oxide interfaces have measured quantities that probe only the magnitude of the superconducting order parameter and are not sensitive to its phase. Here, we perform phase-sensitive measurements by realizing the first superconducting quantum interference devices (SQUIDs) at the LAO/STO interface. Furthermore, we develop a new paradigm for the creation of superconducting circuit elements, where local gates enable the in situ creation and control of Josephson junctions. These gate-defined SQUIDs are unique in that the entire device is made from a single superconductor with purely electrostatic interfaces between the superconducting reservoir and the weak link. We complement our experiments with numerical simulations and show that the low superfluid density of this interfacial superconductor results in a large, gate-controllable kinetic inductance of the SQUID. Our observation of robust quantum interference opens up a new pathway to understanding the nature of superconductivity at oxide interfaces.

Impurity bound states in fully gapped d-wave superconductors with subdominant order parameters

PubMed Central

Mashkoori, Mahdi; Björnson, Kristofer; Black-Schaffer, Annica M.

2017-01-01

Impurities in superconductors and their induced bound states are important both for engineering novel states such as Majorana zero-energy modes and for probing bulk properties of the superconducting state. The high-temperature cuprates offer a clear advantage in a much larger superconducting order parameter, but the nodal energy spectrum of a pure d-wave superconductor only allows virtual bound states. Fully gapped d-wave superconducting states have, however, been proposed in several cuprate systems thanks to subdominant order parameters producing d + is- or d + id′-wave superconducting states. Here we study both magnetic and potential impurities in these fully gapped d-wave superconductors. Using analytical T-matrix and complementary numerical tight-binding lattice calculations, we show that magnetic and potential impurities behave fundamentally different in d + is- and d + id′-wave superconductors. In a d + is-wave superconductor, there are no bound states for potential impurities, while a magnetic impurity produces one pair of bound states, with a zero-energy level crossing at a finite scattering strength. On the other hand, a d + id′-wave symmetry always gives rise to two pairs of bound states and only produce a reachable zero-energy level crossing if the normal state has a strong particle-hole asymmetry. PMID:28281570

Universal linear-temperature resistivity: possible quantum diffusion transport in strongly correlated superconductors.

PubMed

Hu, Tao; Liu, Yinshang; Xiao, Hong; Mu, Gang; Yang, Yi-Feng

2017-08-25

The strongly correlated electron fluids in high temperature cuprate superconductors demonstrate an anomalous linear temperature (T) dependent resistivity behavior, which persists to a wide temperature range without exhibiting saturation. As cooling down, those electron fluids lose the resistivity and condense into the superfluid. However, the origin of the linear-T resistivity behavior and its relationship to the strongly correlated superconductivity remain a mystery. Here we report a universal relation [Formula: see text], which bridges the slope of the linear-T-dependent resistivity (dρ/dT) to the London penetration depth λ L at zero temperature among cuprate superconductor Bi 2 Sr 2 CaCu 2 O 8+δ and heavy fermion superconductors CeCoIn 5 , where μ 0 is vacuum permeability, k B is the Boltzmann constant and ħ is the reduced Planck constant. We extend this scaling relation to different systems and found that it holds for other cuprate, pnictide and heavy fermion superconductors as well, regardless of the significant differences in the strength of electronic correlations, transport directions, and doping levels. Our analysis suggests that the scaling relation in strongly correlated superconductors could be described as a hydrodynamic diffusive transport, with the diffusion coefficient (D) approaching the quantum limit D ~ ħ/m*, where m* is the quasi-particle effective mass.

Spontaneous Hall effect in a chiral p-wave superconductor

NASA Astrophysics Data System (ADS)

Furusaki, Akira; Matsumoto, Masashige; Sigrist, Manfred

2001-08-01

In a chiral superconductor with broken time-reversal symmetry a ``spontaneous Hall effect'' may be observed. We analyze this phenomenon by taking into account the surface properties of a chiral superconductor. We identify two main contributions to the spontaneous Hall effect. One contribution originates from the Bernoulli (or Lorentz) force due to spontaneous currents running along the surfaces of the superconductor. The other contribution has a topological origin and is related to the intrinsic angular momentum of Cooper pairs. The latter can be described in terms of a Chern-Simons-like term in the low-energy field theory of the superconductor and has some similarities with the quantum Hall effect. The spontaneous Hall effect in a chiral superconductor is, however, nonuniversal. Our analysis is based on three approaches to the problem: a self-consistent solution of the Bogoliubov-de Gennes equation, a generalized Ginzburg-Landau theory, and a hydrodynamic formulation. All three methods consistently lead to the same conclusion that the spontaneous Hall resistance of a two-dimensional superconducting Hall bar is of order h/(ekFλ)2, where kF is the Fermi wave vector and λ is the London penetration depth; the Hall resistance is substantially suppressed from a quantum unit of resistance. Experimental issues in measuring this effect are briefly discussed.

New Fe-based superconductors: properties relevant for applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Putti, M; Pallecchi, I; Bellingeri, E

2009-01-01

Less than two years after the discovery of high temperature superconductivity in oxypnictide LaFeAs(O, F) several families of superconductors based on Fe layers (1111, 122, 11, 111) are available. They share several characteristics with cuprate superconductors that compromise easy applications, such as the layered structure, the small coherence length and unconventional pairing. On the other hand, the Fe-based superconductors have metallic parent compounds and their electronic anisotropy is generally smaller and does not strongly depend on the level of doping, and the supposed order parameter symmetry is s-wave, thus in principle not so detrimental to current transmission across grain boundaries.more » From the application point of view, the main efforts are still devoted to investigate the superconducting properties, to distinguish intrinsic from extrinsic behaviors and to compare the different families in order to identify which one is the fittest for the quest for better and more practical superconductors. The 1111 family shows the highest T{sub c}, huge but also the most anisotropic upper critical field and in-field, fan-shaped resistive transitions reminiscent of those of cuprates. On the other hand, the 122 family is much less anisotropic with sharper resistive transitions as in low temperature superconductors, but with about half the T{sub c} of the 1111 compounds. An overview of the main superconducting properties relevant to applications will be presented. Upper critical field, electronic anisotropy parameter, and intragranular and intergranular critical current density will be discussed and compared, where possible, across the Fe-based superconductor families.« less

Magnetic Exchange Coupling in Ferromagnetic/Superconducting/Ferromagnetic Multilayers

NASA Astrophysics Data System (ADS)

de Melo, C. A. R. Sa

2001-03-01

The possibility of magnetic exchange coupling between ferromagnets (F) separated by superconductor (S) spacers in F/S/F multilayers is analysed theoretically [1,2]. Ideal systems for the observation of magnetic coupling through superconductors are complex oxide multilayers consisting of Colossal Magneto-Resistance (CMR) Ferromagnets and High Critical Temperature Cuprate Superconductors. For this coupling to occur, three "prima facie" conditions need to be satisfied. First, an indirect exchange coupling between the ferromagnets must exist when the superconductor is in its normal state. Second, superconductivity must not be destroyed due to the proximity of ferromagnetic boundaries. Third, roughness of the F/S interfaces must be small. Under these conditions, when the superconductor is cooled below its critical temperature T_c, the magnetic coupling changes. The appearance of the superconducting gap introduces a new length scale (the coherence length of the superconductor) and modifies the temperature dependence of the indirect exchange coupling existent in the normal state. The magnetic coupling is oscillatory both above and below T_c, as well as strongly temperature-dependent. However at low temperatures the indirect exchange coupling decay length is controlled by the coherence length of the superconductor, while at temperatures close to and above Tc the magnetic coupling decay length is controlled by the thermal length. [I would like to thank the Georgia Institute of Technology, NSF (Grant No. DMR-9803111) and NATO (Grant No. CRG-972261) for financial support.] [1] C. A. R. Sa de Melo, Phys. Rev. Lett. 79, 1933 (1997). [2] C. A. R. Sa de Melo, Phys. Rev. B 62, 12303 (2000).

Unique and shared validity of the "Wechsler logical memory test", the "California verbal learning test", and the "verbal learning and memory test" in patients with epilepsy.

PubMed

Helmstaedter, Christoph; Wietzke, Jennifer; Lutz, Martin T

2009-12-01

This study was set-up to evaluate the construct validity of three verbal memory tests in epilepsy patients. Sixty-one consecutively evaluated patients with temporal lobe epilepsy (TLE) or extra-temporal epilepsy (E-TLE) underwent testing with the verbal learning and memory test (VLMT, the German equivalent of the Rey auditory verbal learning test, RAVLT); the California verbal learning test (CVLT); the logical memory and digit span subtests of the Wechsler memory scale, revised (WMS-R); and testing of intelligence, attention, speech and executive functions. Factor analysis of the memory tests resulted in test-specific rather than test over-spanning factors. Parameters of the CVLT and WMS-R, and to a much lesser degree of the VLMT, were highly correlated with attention, language function and vocabulary. Delayed recall measures of logical memory and the VLMT differentiated TLE from E-TLE. Learning and memory scores off all three tests differentiated mesial temporal sclerosis from other pathologies. A lateralization of the epilepsy was possible only for a subsample of 15 patients with mesial TLE. Although the three tests provide overlapping indicators for a temporal lobe epilepsy or a mesial pathology, they can hardly be taken in exchange. The tests have different demands on semantic processing and memory organization, and they appear differentially sensitive to performance in non-memory domains. The tests capability to lateralize appears to be poor. The findings encourage the further discussion of the dependency of memory outcomes on test selection.

Improving NIS Tunnel Junction Refrigerators: Modeling, Materials, and Traps

NASA Astrophysics Data System (ADS)

O'Neil, Galen Cascade

This thesis presents a systematic study of electron cooling with Normal-metal/insulator/superconductor (NIS) tunnel junctions. NIS refrigerators have an exciting potential to simplify 100 mK and 10 mK cryogenics. Rather than using an expensive dilution refrigerator, researchers will be able to use much simpler cryogenics to reach 300 mK and supplement them with mass fabricated thin-film NIS refrigerators to reach 100 mK and below. The mechanism enabling NIS refrigeration is energy selective tunneling. Due to the gap in the superconducting density of states, only hot electrons tunnel from the normal-metal. Power is removed from the normal-metal, that same power and the larger IV power are both deposited in the superconductor. NIS refrigerators often cool less than theory predicts because of the power deposited in the superconductor returns to the normal-metal. When the superconductor temperature is raised, or athermal phonons due to quasiparticle recombination are absorbed in the normal-metal, refrigerator performance will be reduced. I studied the quasiparticle excitations in superconductors to develop the most complete thermal model of NIS refrigerators to date. I introduced overlayer quasiparticle traps, a new method for heatsinking the superconductor. I present measurements on NIS refrigerators with and without quasiparticle traps, to determine their effectiveness. This includes an NIS refrigerator that cools from 300 mK to 115 mK or lower, a large improvement over previous designs. I also looked into reducing the power deposited in the superconductor, by choosing the transition temperature of the superconductor based upon the NIS refrigerator launch temperature. I performed a detailed study of the density of states of superconducting AlMn alloys, demonstrating that Mn impurities behave non-magnetically in Al due to resonant scattering. The density of states remains BCS-like, but my measurements show that the deviations from a BCS density of states harm cooling in NIS refrigerators.

Review of Claims of Interaction Between Gravitation and High-Temperature Superconductors

NASA Astrophysics Data System (ADS)

Woods, R. Clive

2004-02-01

Recent reports have claimed that high-temperature superconductors can interact with gravitation under certain non-relativistic conditions. Only two such reports have been peer-reviewed: the first, describing changes in the weight of test masses, was by Podkletnov and Nieminen (1992) the other, reporting large-amplitude gravitational wave generation in a laboratory, was by Podkletnov and Modanese (2003). Common to these reports is the claim that the observed gravitational field may be modified using YBa2Cu3O7-δ (YBCO) below its superconducting critical temperature, Tc ~ 93K, and in a magnetic field B ~ 1T. Temperatures below 70K gave the largest effects. The first experiment used magnetically levitated YBCO rotated at ~5000 rpm; the second experiment did not spin or levitate the YBCO, but used a 2MV electrical discharge in a vacuum chamber. Several attempts have been made world-wide to replicate the first of these experiments, although no peer-reviewed reports have yet confirmed the observations. No known replications of the second experiment have been completed so far. A number of papers have presented theoretical models for the effects. This paper reviews the current experimental and theoretical scientific evidence regarding these experiments, together with further tests implied by the published explanations. The discussion includes a classical suggestion (due to Landau and Lifshitz) that gravitational waves can modify gravitational fields, Aquino's theory based upon electromagnetic fields, and Desbrandes's calculation to explain the Podkletnov and Nieminen results on the basis of gravity waves emitted from the Cooper pairs inside a superconductor. The conclusions are that these experiments are extremely difficult to replicate and that no complete replication confirming the effects has yet taken place. By contrast, no-one has conclusively disproved the existence of the effects.

Person-Fit and the Rasch Model, with an Application to Knowledge of Logical Quantors.

ERIC Educational Resources Information Center

Molenaar, Ivo W.; Hoijtink, Herbert

1996-01-01

Some specific person-fit results for the Rasch model are presented, followed by an application to a test measuring knowledge of reasoning with logical quantors. Some issues are relevant to all attempts to use person-fit statistics in research, but the special role of the Rasch model is highlighted. (SLD)

Math Ties: Problem Solving, Logic Teasers, and Math Puzzles All "Tied" to the Math Curriculum. Book A1.

ERIC Educational Resources Information Center

Santi, Terri

This book contains a classroom-tested approach to the teaching of problem solving to all students in Grades 4-6, regardless of ability. Information on problem solving in general is provided, then mathematical problems on logic, whole numbers, number theory, fractions, decimals, geometry, ratio, proportion, percent, probability, sets, and…

Logic, Beliefs, and Instruction: A Test of the Default Interventionist Account of Belief Bias

ERIC Educational Resources Information Center

Handley, Simon J.; Newstead, Stephen E.; Trippas, Dries

2011-01-01

According to dual-process accounts of thinking, belief-based responses on reasoning tasks are generated as default but can be intervened upon in favor of logical responding, given sufficient time, effort, or cognitive resource. In this article, we present the results of 5 experiments in which participants were instructed to evaluate the…

Logical-Rule Models of Classification Response Times: A Synthesis of Mental-Architecture, Random-Walk, and Decision-Bound Approaches

ERIC Educational Resources Information Center

Fific, Mario; Little, Daniel R.; Nosofsky, Robert M.

2010-01-01

We formalize and provide tests of a set of logical-rule models for predicting perceptual classification response times (RTs) and choice probabilities. The models are developed by synthesizing mental-architecture, random-walk, and decision-bound approaches. According to the models, people make independent decisions about the locations of stimuli…

Mapping individual logical processes in information searching

NASA Technical Reports Server (NTRS)

Smetana, F. O.

1974-01-01

An interactive dialog with a computerized information collection was recorded and plotted in the form of a flow chart. The process permits one to identify the logical processes employed in considerable detail and is therefore suggested as a tool for measuring individual thought processes in a variety of situations. A sample of an actual test case is given.

Text Cohesion and Comprehension: A Comparison of Prose Analysis Systems.

ERIC Educational Resources Information Center

Varnhagen, Connie K.; Goldman, Susan R.

To test three specific hypotheses about recall as a function of four categories of logical relations, a study was done to determine whether logical relations systems of prose analysis can be used to predict recall. Two descriptive passages of naturally occurring expository prose were used. Each text was parsed into 45 statements, consisting of…

Independent effects of relevance and arousal on deductive reasoning.

PubMed

Caparos, Serge; Blanchette, Isabelle

2017-08-01

Emotional content can have either a deleterious or a beneficial impact on logicality. Using standard deductive-reasoning tasks, we tested the hypothesis that the interplay of two factors - personal relevance and arousal - determines the nature of the effect of emotional content on logicality. Arousal was assessed using measures of skin conductance. Personal relevance was manipulated by asking participants to reason about semantic contents linked to an emotional event that they had experienced or not. Findings showed that (1) personal relevance exerts a positive effect on logicality while arousal exerts a negative effect, and that (2) these effects are independent of each other.

Quantum Communication without Alignment using Multiple-Qubit Single-Photon States

NASA Astrophysics Data System (ADS)

Aolita, L.; Walborn, S. P.

2007-03-01

We propose a scheme for encoding logical qubits in a subspace protected against collective rotations around the propagation axis using the polarization and transverse spatial degrees of freedom of single photons. This encoding allows for quantum key distribution without the need of a shared reference frame. We present methods to generate entangled states of two logical qubits using present day down-conversion sources and linear optics, and show that the application of these entangled logical states to quantum information schemes allows for alignment-free tests of Bell’s inequalities, quantum dense coding, and quantum teleportation.

Model checking for linear temporal logic: An efficient implementation

NASA Technical Reports Server (NTRS)

Sherman, Rivi; Pnueli, Amir

1990-01-01

This report provides evidence to support the claim that model checking for linear temporal logic (LTL) is practically efficient. Two implementations of a linear temporal logic model checker is described. One is based on transforming the model checking problem into a satisfiability problem; the other checks an LTL formula for a finite model by computing the cross-product of the finite state transition graph of the program with a structure containing all possible models for the property. An experiment was done with a set of mutual exclusion algorithms and tested safety and liveness under fairness for these algorithms.

Executing medical logic modules expressed in ArdenML using Drools

PubMed Central

Jung, Chai Young; Sward, Katherine A

2011-01-01

The Arden Syntax is an HL7 standard language for representing medical knowledge as logic statements. Despite nearly 2 decades of availability, Arden Syntax has not been widely used. This has been attributed to the lack of a generally available compiler to implement the logic, to Arden's complex syntax, to the challenges of mapping local data to data references in the Medical Logic Modules (MLMs), or, more globally, to the general absence of decision support in healthcare computing. An XML representation (ArdenML) may partially address the technical challenges. MLMs created in ArdenML can be converted into executable files using standard transforms written in the Extensible Stylesheet Language Transformation (XSLT) language. As an example, we have demonstrated an approach to executing MLMs written in ArdenML using the Drools business rule management system. Extensions to ArdenML make it possible to generate a user interface through which an MLM developer can test for logical errors. PMID:22180871

Competing quantum orderings in cuprate superconductors: A minimal model

NASA Astrophysics Data System (ADS)

Martin, I.; Ortiz, G.; Balatsky, A. V.; Bishop, A. R.

2001-02-01

We present a minimal model for cuprate superconductors. At the unrestricted mean-field level, the model produces homogeneous superconductivity at large doping, striped superconductivity in the underdoped regime and various antiferromagnetic phases at low doping and for high temperatures. On the underdoped side, the superconductor is intrinsically inhomogeneous and global phase coherence is achieved through Josephson-like coupling of the superconducting stripes. The model is applied to calculate experimentally measurable ARPES spectra.

Superconductivity in Cuba: Reaching the Frontline

NASA Astrophysics Data System (ADS)

Arés Muzio, Oscar; Altshuler, Ernesto

The start of experimental research in the field of superconductivity was a very special moment for Cuban physics: Cuban scientists at the Physics Faculty, University of Havana, synthesized the first Cuban superconductor (a 123-YBCO ceramic sample) just 2 months after the publication of the famous paper by Wu and co-workers that triggered the frantic race of High Tc superconductors all over the world. We timely joined the world's frontline in superconductor research.

Bearing design for flywheel energy storage using high-TC superconductors

DOEpatents

Hull, John R.; Mulcahy, Thomas M.

2000-01-01

A high temperature superconductor material bearing system (38) This system (38) includes a rotor (50) having a ring permanent magnet (60), a plurality of permanent magnets (16, 20 and 70) for interacting to generate levitation forces for the system (38). This group of magnets are a push/pull bearing (75). A high temperature superconductor structure (30) interacts with the ting permanent magnet (60) to provide stabilizing forces for the system (38).

Experimental Setup for the Investigation of Superconducting Persistent Current

DTIC Science & Technology

2015-09-01

This documentation is intended to support future investigations of coated conductors in either tape or wire form or for bulk superconductors in an...Introduction Second-generation, high-temperature, coated superconductors , such as yttrium barium copper oxide (Y1Ba2Cu3O7-δ, or REBCO, or RE123), are...source applications.8 In order to push the high-temperature superconductors to a more mature degree, new knowledge and deeper understanding of the

Magnetic-Field Dependences of Thermodynamic Quantities in the Vortex State of Type-Ii Superconductors

NASA Astrophysics Data System (ADS)

Watanabe, Koichi; Kita, Takafumi; Arai, Masao

2006-08-01

We develop an alternative method to solve the Eilenberger equations numerically for the vortex-lattice states of type-II superconductors. Using it, we clarify the magnetic-field and impurity-concentration dependences of the magnetization, the entropy, the Pauli paramagnetism, and the mixing of higher Landau levels in the pair potential for two-dimensional s- and dx2-y2-wave superconductors with a cylindrical Fermi surface.

Conversion Gain in MM-Wave Quasiparticle Heterodyne Mixers,

DTIC Science & Technology

1981-01-01

superconductor-insulating oxide -superconductor SIS (Josephson) tunnel junc- tions [4-141. Due to the singularity in density of states of quasiparticles in the...superconductors on two sides of the oxide barrier, there is a sudden onset of quasiparticle tunneling current at bias voltage near the full...Phillips, and D. P. Woody, ’Low noise 115 GHz mixing in supercon- ducting oxide barrier tunnel junctions,’ App. Phys. Lett., vol. 34, pp. 347-349, March

Compact terahertz passive spectrometer with wideband superconductor-insulator-superconductor mixer.

PubMed

Kikuchi, K; Kohjiro, S; Yamada, T; Shimizu, N; Wakatsuki, A

2012-02-01

We developed a compact terahertz (THz) spectrometer with a superconductor-insulator-superconductor (SIS) mixer, aiming to realize a portable and highly sensitive spectrometer to detect dangerous gases at disaster sites. The receiver cryostat which incorporates the SIS mixer and a small cryocooler except for a helium compressor has a weight of 27 kg and dimensions of 200 mm × 270 mm × 690 mm. In spite of the small cooling capacity of the cryocooler, the SIS mixer is successfully cooled lower than 4 K, and the temperature variation is suppressed for the sensitive measurement. By adopting a frequency sweeping system using photonic local oscillator, we demonstrated a spectroscopic measurement of CH(3)CN gas in 0.2-0.5 THz range.

A 0.2-0.5 THz single-band heterodyne receiver based on a photonic local oscillator and a superconductor-insulator-superconductor mixer

NASA Astrophysics Data System (ADS)

Kohjiro, Satoshi; Kikuchi, Kenichi; Maezawa, Masaaki; Furuta, Tomofumi; Wakatsuki, Atsushi; Ito, Hiroshi; Shimizu, Naofumi; Nagatsuma, Tadao; Kado, Yuichi

2008-09-01

We have demonstrated that a superconductor-insulator-superconductor (SIS) mixer pumped by a photonic local oscillator (LO) covers the whole frequency range of 0.2-0.5THz. In the bandwidth of 74% of the center frequency, this single-band receiver exhibits noise temperature of TRX⩽20hf/kB, where h is Planck's constant, f is the frequency, and kB is Boltzmann's constant. Resultant TRX is almost equal to TRX of the identical SIS mixer pumped by three conventional frequency-multiplier-based LOs which share the 0.2-0.5THz band. This technique will contribute to simple, wide-band, and low-noise heterodyne receivers in the terahertz region.

Superconductor Permanent Magnets for Advanced Propulsion Applications

NASA Astrophysics Data System (ADS)

Putman, Phil; Zhou, Yuxiang; Salama, Kamel; Robertson, Tony; Bond, Deborah D.

2005-02-01

Improved trapped fields of 17 T at 29 K and 11.2 T at 47 K have been reported for the melt-textured YBCO superconductor material. Such high field strengths give the possibility for producing superconductor permanent magnets (SCPM) for plasma-related space propulsion applications, such as the anti-matter trap, magnetohydrodynamic (MHD) propulsion and electrical power generation, and others that are under development or being studied. The SCPM could be beneficial in reducing the weight-to-power ratio for the associated delivery and containment systems needed for plasma interactions that are inherently imbedded in many of these propulsion systems. In this paper, a review of the superconductor literature is presented, followed by uses of the SCPM in high-performance space propulsion applications.

High-temperature superconductor antenna investigations

NASA Technical Reports Server (NTRS)

Karasack, Vincent G.

1990-01-01

The use of superconductors to increase antenna radiation efficiency and gain is examined. Although the gain of all normal-metal antennas can be increased through the use of superconductors, some structures have greater potential for practical improvement than others. Some structures suffer a great degradation in bandwidth when replaced with superconductors, while for others the improvement in efficiency is trivial due to the minimal contribution of the conductor loss mechanism to the total losses, or the already high efficiency of the structure. The following antennas and related structures are discussed: electrically small antennas, impedance matching of antennas, microstrip antennas, microwave and millimeter-wave antenna arrays, and superdirective arrays. The greatest potential practical improvements occur for large microwave and millimeter-wave arrays and the impedance matching of antennas.

Local antiferromagnetic exchange and collaborative Fermi surface as key ingredients of high temperature superconductors

PubMed Central

Hu, Jiangping; Ding, Hong

2012-01-01

Cuprates, ferropnictides and ferrochalcogenides are three classes of unconventional high temperature superconductors, who share similar phase diagrams in which superconductivity develops after a magnetic order is suppressed, suggesting a strong interplay between superconductivity and magnetism, although the exact picture of this interplay remains elusive. Here we show that there is a direct bridge connecting antiferromagnetic exchange interactions determined in the parent compounds of these materials to the superconducting gap functions observed in the corresponding superconducting materials: in all high temperature superconductors, the Fermi surface topology matches the form factor of the pairing symmetry favored by local magnetic exchange interactions. We suggest that this match offers a principle guide to search for new high temperature superconductors. PMID:22536479

Flux pinning characteristics and irreversibility line in high temperature superconductors

NASA Technical Reports Server (NTRS)

Matsushita, T.; Ihara, N.; Kiuchi, M.

1995-01-01

The flux pinning properties in high temperature superconductors are strongly influenced by thermally activated flux motion. The scaling relation of the pinning force density and the irreversibility line in various high temperature superconductors are numerically analyzed in terms of the flux creep model. The effect of two factors, i.e., the flux pinning strength and the dimensionality of the material, on these properties are investigated. It is speculated that the irreversibility line in Bi-2212 superconductors is one order of magnitude smaller than that in Y-123, even if the flux pinning strength in Bi-2212 is improved up to the level of Y-123. It is concluded that these two factors are equally important in determination of the flux pinning characteristics at high temperatures.

Tunable (δπ, δπ)-Type Antiferromagnetic Order in α-Fe(Te,Se) Superconductors

NASA Astrophysics Data System (ADS)

Bao, Wei; Qiu, Y.; Huang, Q.; Green, M. A.; Zajdel, P.; Fitzsimmons, M. R.; Zhernenkov, M.; Chang, S.; Fang, Minghu; Qian, B.; Vehstedt, E. K.; Yang, Jinhu; Pham, H. M.; Spinu, L.; Mao, Z. Q.

2009-06-01

The new α-Fe(Te,Se) superconductors share the common iron building block and ferminology with the LaFeAsO and BaFe2As2 families of superconductors. In contrast with the predicted commensurate spin-density-wave order at the nesting wave vector (π, 0), a completely different magnetic order with a composition tunable propagation vector (δπ, δπ) was determined for the parent compound Fe1+yTe in this powder and single-crystal neutron diffraction study. The new antiferromagnetic order survives as a short-range one even in the highest TC sample. An alternative to the prevailing nesting Fermi surface mechanism is required to understand the latest family of ferrous superconductors.

High Tc superconductors as thermal radiation shields

NASA Astrophysics Data System (ADS)

Zeller, A. F.

1990-06-01

The feasibility of using high-Tc superconductor films as IR-radiation shields for liquid-helium-temperature dewars is investigated. Calculations show that a Ba-Ca-Sr-Cu-O superconductor with Tc of 110 K, combined with a liquid-nitrogen temperature shield with an emissivity of 0.03 should produce an upper limit to the radiative heat transfer of 15 mW/sq m. The reduction of reflectivity depends on the field level and the extent of field penetration into the superconductor film, whose surface also would provide magnetic shielding for low magnetic fields. Such shields, providing both magnetic and thermal radiation shielding would be useful for spaceborne applications where exposure to the degrading effects of moist air would not be a problem.

Electron teleportation via Majorana bound states in a mesoscopic superconductor.

PubMed

Fu, Liang

2010-02-05

Zero-energy Majorana bound states in superconductors have been proposed to be potential building blocks of a topological quantum computer, because quantum information can be encoded nonlocally in the fermion occupation of a pair of spatially separated Majorana bound states. However, despite intensive efforts, nonlocal signatures of Majorana bound states have not been found in charge transport. In this work, we predict a striking nonlocal phase-coherent electron transfer process by virtue of tunneling in and out of a pair of Majorana bound states. This teleportation phenomenon only exists in a mesoscopic superconductor because of an all-important but previously overlooked charging energy. We propose an experimental setup to detect this phenomenon in a superconductor-quantum-spin-Hall-insulator-magnetic-insulator hybrid system.

Method and system for an on-chip AC self-test controller

DOEpatents

Flanagan, John D [Rhinebeck, NY; Herring, Jay R [Poughkeepsie, NY; Lo, Tin-Chee [Fishkill, NY

2008-09-30

A method and system for performing AC self-test on an integrated circuit that includes a system clock for use during normal operation are provided. The method includes applying a long data capture pulse to a first test register in response to the system clock, applying an at speed data launch pulse to the first test register in response to the system clock, inputting the data from the first register to a logic path in response to applying the at speed data launch pulse to the first test register, applying an at speed data capture pulse to a second test register in response to the system clock, inputting the logic path output to the second test register in response to applying the at speed data capture pulse to the second test register, and applying a long data launch pulse to the second test register in response to the system clock.

Cooling Stability Test of MgB2 Wire Immersed in Liquid Hydrogen under External Magnetic Field

NASA Astrophysics Data System (ADS)

Shirai, Yasuyuki; Hikawa, Kyosuke; Shiotsu, Masahiro; Tatsumoto, Hideki; Naruo, Yoshihiro; Kobayashi, Hiroaki; Inagaki, Yoshifumi

2014-05-01

Liquid hydrogen (LH2), which has large latent heat, low viscosity coefficient, is expected to be a candidate for a cryogen for superconducting wires, not only MgB2 but also other HTC superconductors. LH2 cooled superconducting wires are expected to have excellent electro-magnetic characteristics, which is necessary to be clear for cooling stability design of LH2 cooled superconducting device, however, due to handling difficulties of LH2, there are only few papers on the properties of LH2 cooled superconductors, especially under external magnetic field. We designed and made an experimental setup which can energize superconducting wires immersed in LH2 with the current of up to 500A under the condition of external magnetic field up to 7 T and pressure up to 1.5 MPa. In order to confirm experimental method and safety operation of the setup, over current tests were carried out using MgB2 superconducting wires under various external magnetic field conditions. Critical current of the test wire at the temperature 21, 24, 27, 29 K under external magnetic fields up to 1.2 T was successfully measured. The resistance of the wire also was measured, while the transport current exceeded the critical current of the wire.

NSSEFF Designing New Higher Temperature Superconductors

DTIC Science & Technology

2017-04-13

electronic structure calculations are integrated with the synthesis of new superconducting materials, with the aim of providing a rigorous test of the...apparent association of high temperature superconductivity with electron delocalization transitions occurring at quantum critical points. We will use...realistic electronic structure calculations to assess which transition metal monopnictides are closest to electron delocalization, and hence optimal for

Microwave amplification based on quasiparticle SIS up and down frequency converters

NASA Astrophysics Data System (ADS)

Kojima, T.; Uzawa, Y.; Shan, W.

2018-02-01

Heterodyne instruments have recently attained quantum-limited low-noise performance, particularly in radio astronomy, but it is difficult to develop large heterodyne arrays such as a modern radio camera using cryogenic sensitive detectors based on microwave kinetic inductance detectors, transition edge sensors, etc. In the realization of the heterodyne array, the reduction of power dissipation for semiconductor-based amplifiers remains a major challenge. Alternatively, superconducting parametric amplifiers still seem to have several barriers to application, especially in terms of operating temperature. Here, we show a novel concept of microwave amplification based on up and down frequency-conversion processes using quasiparticle superconductor-insulator-superconductor (SIS) tunnel junctions. We demonstrate positive gain using a proof-of-concept test module, which operates with a power dissipation of several μW at a bath temperature of 4 K. The performance of the module suggests great potential for application in large arrays.

A linear induction motor with a coated conductor superconducting secondary

NASA Astrophysics Data System (ADS)

Chen, Xin; Zheng, Shijun; Li, Jing; Ma, Guang Tong; Yen, Fei

2018-07-01

A linear induction motor system composed of a high-Tc superconducting secondary with close-ended coils made of REBCO coated conductor wire was designed and tested experimentally. The measured thrust, normal force and power loss are presented and explained by combining the flux dynamics inside superconductors with existing linear drive theory. It is found that an inherent capacitive component associated to the flux motion of vortices in the Type-II superconductor reduces the impedance of the coils; from such, the associated Lorentz forces are drastically increased. The resulting breakout thrust of the designed linear motor system was found to be extremely high (up to 4.7 kN/m2) while the associated normal forces only a fraction of the thrust. Compared to its conventional counterparts, high-Tc superconducting secondaries appear to be more feasible for use in maglev propulsion and electromagnetic launchers.

Hole-doped cuprate high temperature superconductors

NASA Astrophysics Data System (ADS)

Chu, C. W.; Deng, L. Z.; Lv, B.

2015-07-01

Hole-doped cuprate high temperature superconductors have ushered in the modern era of high temperature superconductivity (HTS) and have continued to be at center stage in the field. Extensive studies have been made, many compounds discovered, voluminous data compiled, numerous models proposed, many review articles written, and various prototype devices made and tested with better performance than their nonsuperconducting counterparts. The field is indeed vast. We have therefore decided to focus on the major cuprate materials systems that have laid the foundation of HTS science and technology and present several simple scaling laws that show the systematic and universal simplicity amid the complexity of these material systems, while referring readers interested in the HTS physics and devices to the review articles. Developments in the field are mostly presented in chronological order, sometimes with anecdotes, in an attempt to share some of the moments of excitement and despair in the history of HTS with readers, especially the younger ones.

^17O NMR Study of Sr_2CuO_2Cl_2, a Single-Layer Parent Compound of a High Tc Superconductor

NASA Astrophysics Data System (ADS)

Thurber, Kent; Hunt, Allen; Imai, Takashi; Chou, Fang-Cheng; Lee, Young

1997-03-01

We report NMR measurements of the ^17O nuclear spin-lattice relaxation rate 1/T_1, and the ^17O Knight shift of Sr_2CuO_2Cl2 (TN = 257 K) in the paramagnetic state from the Néel temperature up to 700 K. This establishes, for the first time, the temperature and frequency dependence of ^17O NMR in the paramagnetic state of a clean, single-layer, undoped parent compound of a high Tc superconductor. The ^17O NMR results test the nature of elementary spin excitations around q = 0 and give insight into the spin wave damping, Γ. The observation, ^17 1/T1 ~ a T^3 [ 1 + O(T/J) ], agrees semi-quantitatively with theoretical predictions based on spin waves in the spin S=1/2 2D Heisenberg model. electronically.

US Navy superconductivity program

NASA Technical Reports Server (NTRS)

Gubser, Donald U.

1991-01-01

Both the new high temperature superconductors (HTS) and the low temperature superconductors (LTS) are important components of the Navy's total plan to integrate superconductivity into field operational systems. Fundamental research is an important component of the total Navy program and focuses on the HTS materials. Power applications (ship propulsion) use LTS materials while space applications (millimeter wave electronics) use HTS materials. The Space Experiment to be conducted at NRL will involve space flight testing of HTS devices built by industry and will demonstrate the ability to engineer and space qualify these devices for systems use. Another important component of the Navy's effort is the development of Superconducting Quantum Interference Device (SQUID) magnetometers. This program will use LTS materials initially, but plans to implement HTS materials as soon as possible. Hybrid HTS/LTS systems are probable in many applications. A review of the status of the Navy's HTS materials research is given as well as an update on the Navy's development efforts in superconductivity.

Effect of spin fluctuations on the electronic structure in iron-based superconductors

NASA Astrophysics Data System (ADS)

Heimes, Andreas; Grein, Roland; Eschrig, Matthias

2012-08-01

Magnetic inelastic neutron scattering studies of iron-based superconductors reveal a strongly temperature-dependent spin-fluctuation spectrum in the normal conducting state, which develops a prominent low-energy resonance feature when entering the superconducting state. Angle-resolved photoemission spectroscopy (ARPES) and scanning tunneling spectroscopy (STS) allow us to study the fingerprints of fluctuation modes via their interactions with electronic quasiparticles. We calculate such fingerprints in 122 iron pnictides using an experimentally motivated spin-fluctuation spectrum and make a number of predictions that can be tested in ARPES and STS experiments. This includes discussions of the quasiparticle scattering rate and the superconducting order parameter. In quantitative agreement with experiment we reproduce the quasiparticle dispersions obtained from momentum distribution curves as well as energy distribution curves. We discuss the relevance of the coupling between spin fluctuations and electronic excitations for the superconducting mechanism.

Knowledge discovery from structured mammography reports using inductive logic programming.

PubMed

Burnside, Elizabeth S; Davis, Jesse; Costa, Victor Santos; Dutra, Inês de Castro; Kahn, Charles E; Fine, Jason; Page, David

2005-01-01

The development of large mammography databases provides an opportunity for knowledge discovery and data mining techniques to recognize patterns not previously appreciated. Using a database from a breast imaging practice containing patient risk factors, imaging findings, and biopsy results, we tested whether inductive logic programming (ILP) could discover interesting hypotheses that could subsequently be tested and validated. The ILP algorithm discovered two hypotheses from the data that were 1) judged as interesting by a subspecialty trained mammographer and 2) validated by analysis of the data itself.

Synthesizing Dynamic Programming Algorithms from Linear Temporal Logic Formulae

NASA Technical Reports Server (NTRS)

Rosu, Grigore; Havelund, Klaus

2001-01-01

The problem of testing a linear temporal logic (LTL) formula on a finite execution trace of events, generated by an executing program, occurs naturally in runtime analysis of software. We present an algorithm which takes an LTL formula and generates an efficient dynamic programming algorithm. The generated algorithm tests whether the LTL formula is satisfied by a finite trace of events given as input. The generated algorithm runs in linear time, its constant depending on the size of the LTL formula. The memory needed is constant, also depending on the size of the formula.

Integration of relational and textual biomedical sources. A pilot experiment using a semi-automated method for logical schema acquisition.

PubMed

García-Remesal, M; Maojo, V; Billhardt, H; Crespo, J

2010-01-01

Bringing together structured and text-based sources is an exciting challenge for biomedical informaticians, since most relevant biomedical sources belong to one of these categories. In this paper we evaluate the feasibility of integrating relational and text-based biomedical sources using: i) an original logical schema acquisition method for textual databases developed by the authors, and ii) OntoFusion, a system originally designed by the authors for the integration of relational sources. We conducted an integration experiment involving a test set of seven differently structured sources covering the domain of genetic diseases. We used our logical schema acquisition method to generate schemas for all textual sources. The sources were integrated using the methods and tools provided by OntoFusion. The integration was validated using a test set of 500 queries. A panel of experts answered a questionnaire to evaluate i) the quality of the extracted schemas, ii) the query processing performance of the integrated set of sources, and iii) the relevance of the retrieved results. The results of the survey show that our method extracts coherent and representative logical schemas. Experts' feedback on the performance of the integrated system and the relevance of the retrieved results was also positive. Regarding the validation of the integration, the system successfully provided correct results for all queries in the test set. The results of the experiment suggest that text-based sources including a logical schema can be regarded as equivalent to structured databases. Using our method, previous research and existing tools designed for the integration of structured databases can be reused - possibly subject to minor modifications - to integrate differently structured sources.

Method and system for an on-chip AC self-test controller

DOEpatents

Flanagan, John D.; Herring, Jay R.; Lo, Tin-Chee

2006-06-06

A method for performing AC self-test on an integrated circuit, including a system clock for use during normal operation. The method includes applying a long data capture pulse to a first test register in response to the system clock, and further applying at an speed data launch pulse to the first test register in response to the system clock. Inputting the data from the first register to a logic path in response to applying the at speed data launch pulse to the first test register. Applying at speed data capture pulse to a second test register in response to the system clock. Inputting the output from the logic path to the second test register in response to applying the at speed data capture pulse to the second register. Applying a long data launch pulse to the second test register in response to the system clock.

Computerized engineering logic for nuclear procurement and dedication processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tulay, M.P.

1996-12-31

In an attempt to better meet the needs of operations and maintenance organizations, many nuclear utility procurement engineering groups have simplified their procedures, developed on-line tools for performing the specification of replacement items, and developed relational databases containing part-level information necessary to automate the procurement process. Although these improvements have helped to reduce the engineering necessary to properly specify and accept/dedicate items for nuclear safety-related applications, a number of utilities have recognized that additional long-term savings can be realized by integrating a computerized logic to assist technical procurement engineering personnel. The most commonly used logic follows the generic processes containedmore » in Electric Power Research Institute (EPRI) published guidelines. The processes are typically customized to some extent to accommodate each utility`s organizational structure, operating procedures, and strategic goals. This paper will discuss a typical logic that integrates the technical evaluation, acceptance, and receipt inspection and testing processes. The logic this paper will describe has been successfully integrated at a growing number of nuclear utilities and has produced numerous positive results. The application of the logic ensures that utility-wide standards or procedures, common among multi-site utilities, are followed.« less

Test functions for three-dimensional control-volume mixed finite-element methods on irregular grids

USGS Publications Warehouse

Naff, R.L.; Russell, T.F.; Wilson, J.D.; ,; ,; ,; ,; ,

2000-01-01

Numerical methods based on unstructured grids, with irregular cells, usually require discrete shape functions to approximate the distribution of quantities across cells. For control-volume mixed finite-element methods, vector shape functions are used to approximate the distribution of velocities across cells and vector test functions are used to minimize the error associated with the numerical approximation scheme. For a logically cubic mesh, the lowest-order shape functions are chosen in a natural way to conserve intercell fluxes that vary linearly in logical space. Vector test functions, while somewhat restricted by the mapping into the logical reference cube, admit a wider class of possibilities. Ideally, an error minimization procedure to select the test function from an acceptable class of candidates would be the best procedure. Lacking such a procedure, we first investigate the effect of possible test functions on the pressure distribution over the control volume; specifically, we look for test functions that allow for the elimination of intermediate pressures on cell faces. From these results, we select three forms for the test function for use in a control-volume mixed method code and subject them to an error analysis for different forms of grid irregularity; errors are reported in terms of the discrete L2 norm of the velocity error. Of these three forms, one appears to produce optimal results for most forms of grid irregularity.

Nature of the superconductor-insulator transition in disordered superconductors.

PubMed

Dubi, Yonatan; Meir, Yigal; Avishai, Yshai

2007-10-18

The interplay of superconductivity and disorder has intrigued scientists for several decades. Disorder is expected to enhance the electrical resistance of a system, whereas superconductivity is associated with a zero-resistance state. Although superconductivity has been predicted to persist even in the presence of disorder, experiments performed on thin films have demonstrated a transition from a superconducting to an insulating state with increasing disorder or magnetic field. The nature of this transition is still under debate, and the subject has become even more relevant with the realization that high-transition-temperature (high-T(c)) superconductors are intrinsically disordered. Here we present numerical simulations of the superconductor-insulator transition in two-dimensional disordered superconductors, starting from a microscopic description that includes thermal phase fluctuations. We demonstrate explicitly that disorder leads to the formation of islands where the superconducting order is high. For weak disorder, or high electron density, increasing the magnetic field results in the eventual vanishing of the amplitude of the superconducting order parameter, thereby forming an insulating state. On the other hand, at lower electron densities or higher disorder, increasing the magnetic field suppresses the correlations between the phases of the superconducting order parameter in different islands, giving rise to a different type of superconductor-insulator transition. One of the important predictions of this work is that in the regime of high disorder, there are still superconducting islands in the sample, even on the insulating side of the transition. This result, which is consistent with experiments, explains the recently observed huge magneto-resistance peak in disordered thin films and may be relevant to the observation of 'the pseudogap phenomenon' in underdoped high-T(c) superconductors.