Dynamic frame resizing with convolutional neural network for efficient video compression

NASA Astrophysics Data System (ADS)

Kim, Jaehwan; Park, Youngo; Choi, Kwang Pyo; Lee, JongSeok; Jeon, Sunyoung; Park, JeongHoon

2017-09-01

In the past, video codecs such as vc-1 and H.263 used a technique to encode reduced-resolution video and restore original resolution from the decoder for improvement of coding efficiency. The techniques of vc-1 and H.263 Annex Q are called dynamic frame resizing and reduced-resolution update mode, respectively. However, these techniques have not been widely used due to limited performance improvements that operate well only under specific conditions. In this paper, video frame resizing (reduced/restore) technique based on machine learning is proposed for improvement of coding efficiency. The proposed method features video of low resolution made by convolutional neural network (CNN) in encoder and reconstruction of original resolution using CNN in decoder. The proposed method shows improved subjective performance over all the high resolution videos which are dominantly consumed recently. In order to assess subjective quality of the proposed method, Video Multi-method Assessment Fusion (VMAF) which showed high reliability among many subjective measurement tools was used as subjective metric. Moreover, to assess general performance, diverse bitrates are tested. Experimental results showed that BD-rate based on VMAF was improved by about 51% compare to conventional HEVC. Especially, VMAF values were significantly improved in low bitrate. Also, when the method is subjectively tested, it had better subjective visual quality in similar bit rate.

Region of interest based robust watermarking scheme for adaptation in small displays

NASA Astrophysics Data System (ADS)

Vivekanandhan, Sapthagirivasan; K. B., Kishore Mohan; Vemula, Krishna Manohar

2010-02-01

Now-a-days Multimedia data can be easily replicated and the copyright is not legally protected. Cryptography does not allow the use of digital data in its original form and once the data is decrypted, it is no longer protected. Here we have proposed a new double protected digital image watermarking algorithm, which can embed the watermark image blocks into the adjacent regions of the host image itself based on their blocks similarity coefficient which is robust to various noise effects like Poisson noise, Gaussian noise, Random noise and thereby provide double security from various noises and hackers. As instrumentation application requires a much accurate data, the watermark image which is to be extracted back from the watermarked image must be immune to various noise effects. Our results provide better extracted image compared to the present/existing techniques and in addition we have done resizing the same for various displays. Adaptive resizing for various size displays is being experimented wherein we crop the required information in a frame, zoom it for a large display or resize for a small display using a threshold value and in either cases background is not given much importance but it is only the fore-sight object which gains importance which will surely be helpful in performing surgeries.

Resizing procedure for structures under combined mechanical and thermal loading

NASA Technical Reports Server (NTRS)

Adelman, H. M.; Narayanaswami, R.

1976-01-01

The fully-stressed design (FSD) appears to be the most widely used approach for sizing of flight structures under strength and minimum-gage constraints. Almost all of the experience with FSD has been with structures primarily under mechanical loading as opposed to thermal loading. In this method the structural sizes are iterated with the step size, depending on the ratio of the total stress to the allowable stress. In this paper, the thermal fully-stressed design (TFSD) procedure developed for problems involving substantial thermal stress is extended to biaxial stress members using a Von Mises failure criterion. The TFSD resizing procedure for uniaxial stress is restated and the new procedure for biaxial stress members is developed. Results are presented for an application of the two procedures to size a simplified wing structure.

Exploiting parallel computing with limited program changes using a network of microcomputers

NASA Technical Reports Server (NTRS)

Rogers, J. L., Jr.; Sobieszczanski-Sobieski, J.

1985-01-01

Network computing and multiprocessor computers are two discernible trends in parallel processing. The computational behavior of an iterative distributed process in which some subtasks are completed later than others because of an imbalance in computational requirements is of significant interest. The effects of asynchronus processing was studied. A small existing program was converted to perform finite element analysis by distributing substructure analysis over a network of four Apple IIe microcomputers connected to a shared disk, simulating a parallel computer. The substructure analysis uses an iterative, fully stressed, structural resizing procedure. A framework of beams divided into three substructures is used as the finite element model. The effects of asynchronous processing on the convergence of the design variables are determined by not resizing particular substructures on various iterations.

A Methodology to Assess the Accuracy with which Remote Data Characterize a Specific Surface, as a Function of Full Width at Half Maximum (FWHM): Application to Three Italian Coastal Waters

PubMed Central

Cavalli, Rosa Maria; Betti, Mattia; Campanelli, Alessandra; Di Cicco, Annalisa; Guglietta, Daniela; Penna, Pierluigi; Piermattei, Viviana

2014-01-01

This methodology assesses the accuracy with which remote data characterizes a surface, as a function of Full Width at Half Maximum (FWHM). The purpose is to identify the best remote data that improves the characterization of a surface, evaluating the number of bands in the spectral range. The first step creates an accurate dataset of remote simulated data, using in situ hyperspectral reflectances. The second step evaluates the capability of remote simulated data to characterize this surface. The spectral similarity measurements, which are obtained using classifiers, provide this capability. The third step examines the precision of this capability. The assumption is that in situ hyperspectral reflectances are considered the “real” reflectances. They are resized with the same spectral range of the remote data. The spectral similarity measurements which are obtained from “real” resized reflectances, are considered “real” measurements. Therefore, the quantity and magnitude of “errors” (i.e., differences between spectral similarity measurements obtained from “real” resized reflectances and from remote data) provide the accuracy as a function of FWHM. This methodology was applied to evaluate the accuracy with which CHRIS-mode1, CHRIS-mode2, Landsat5-TM, MIVIS and PRISMA data characterize three coastal waters. Their mean values of uncertainty are 1.59%, 3.79%, 7.75%, 3.15% and 1.18%, respectively. PMID:24434875

Automotive Manufacturing Processes. volume I - Overview

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and re-sizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pr...

Automotive Manufacturing Processes. Volume I - Overview

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and re-sizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pr...

Adaptively resizing populations: Algorithm, analysis, and first results

NASA Technical Reports Server (NTRS)

Smith, Robert E.; Smuda, Ellen

1993-01-01

Deciding on an appropriate population size for a given Genetic Algorithm (GA) application can often be critical to the algorithm's success. Too small, and the GA can fall victim to sampling error, affecting the efficacy of its search. Too large, and the GA wastes computational resources. Although advice exists for sizing GA populations, much of this advice involves theoretical aspects that are not accessible to the novice user. An algorithm for adaptively resizing GA populations is suggested. This algorithm is based on recent theoretical developments that relate population size to schema fitness variance. The suggested algorithm is developed theoretically, and simulated with expected value equations. The algorithm is then tested on a problem where population sizing can mislead the GA. The work presented suggests that the population sizing algorithm may be a viable way to eliminate the population sizing decision from the application of GA's.

Automotive Manufacturing Processes. Volume III - Casting and Forging Processes

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and resizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pro...

Automotive Manufacturing Processes. Volume IV - Metal Stamping and Plastic Forming Processes

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and resizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pro...

Automotive Manufacturing Processes. Volume II - Manufacturing Processes for Passive Restraint Systems

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and resizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pro...

Line Segmentation in Handwritten Assamese and Meetei Mayek Script Using Seam Carving Based Algorithm

NASA Astrophysics Data System (ADS)

Kumar, Chandan Jyoti; Kalita, Sanjib Kr.

Line segmentation is a key stage in an Optical Character Recognition system. This paper primarily concerns the problem of text line extraction on color and grayscale manuscript pages of two major North-east Indian regional Scripts, Assamese and Meetei Mayek. Line segmentation of handwritten text in Assamese and Meetei Mayek scripts is an uphill task primarily because of the structural features of both the scripts and varied writing styles. Line segmentation of a document image is been achieved by using the Seam carving technique, in this paper. Researchers from various regions used this approach for content aware resizing of an image. However currently many researchers are implementing Seam Carving for line segmentation phase of OCR. Although it is a language independent technique, mostly experiments are done over Arabic, Greek, German and Chinese scripts. Two types of seams are generated, medial seams approximate the orientation of each text line, and separating seams separated one line of text from another. Experiments are performed extensively over various types of documents and detailed analysis of the evaluations reflects that the algorithm performs well for even documents with multiple scripts. In this paper, we present a comparative study of accuracy of this method over different types of data.

Randomized Controlled Trial of Daily Text Messages to Support Adherence to Preexposure Prophylaxis in Individuals at Risk for Human Immunodeficiency Virus: The TAPIR Study.

PubMed

Moore, David J; Jain, Sonia; Dubé, Michael P; Daar, Eric S; Sun, Xiaoying; Young, Jason; Corado, Katya; Ellorin, Eric; Milam, Joel; Collins, Deborah; Blumenthal, Jill; Best, Brookie M; Anderson, Peter; Haubrich, Richard; Morris, Sheldon R

2018-05-02

Adherence is critical for efficacy of tenofovir disoproxil fumarate/emtricitabine (FTC) as preexposure prophylaxis (PrEP). Between February 2013 and February 2016, 398 men who have sex with men and transgender women were randomized 1:1 to receive individualized texting for adherence building (iTAB) or standard care (SoC) for 48 weeks. The primary endpoint was dried blood spot (DBS) tenofovir diphosphate (TFV-DP) concentrations at both week 12 and the last on-drug visit of >719 fmol/punch (ie, adequate adherence). Secondary outcomes included DBS TFV-DP concentrations of >1246 fmol/punch (ie, near-perfect adherence) and plasma FTC >350 ng/mL (consistent with dosing within the past 24 hours). Concentrations >719 fmol/punch of TFV-DP were found in 88.6% of participants at week 12 and 82.5% at week 48. For the primary endpoint, the study arms did not differ (72.0% in iTAB and 69.2% in SoC; P > .05). For the secondary composite endpoint of >1246 fmol/punch the iTAB arm was superior to SoC (33.5% vs 24.8%; P = .06), reaching statistical significance when adjusting for age (odds ratio, 1.56 [95% confidence interval, 1.00-2.42]; P < .05). At week 48, iTAB was superior to SoC for near-perfect adherence (51.0% vs 37.4%; P = .02). At week 12, iTAB was superior to SoC for dosing in past 24 hours by plasma FTC (47.5% vs 33.3%; P = .007), but not at weeks 24, 36, and 48 (all P > .05). Automated text messaging is a low-burden tool that improves durability of near-perfect PrEP adherence. NCT01761643.

7 CFR 983.155 - Reinspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA... that is pin-picked, hand-sorted, color-sorted, and/or resized is considered to be “materially changed..., handlers exempted from order requirements under § 983.92 are exempt from all reinspection requirements. [70...

Configuration and Management of Wireless Sensor Networks

DTIC Science & Technology

2005-12-01

monitor network status. B. CONCLUSIONS AND FUTURE WORK WSNs are an exciting and useful technology which will be used in various areas in the...int h = getSize().height; Image resizedImage = null; ImageFilter replicate = new ReplicateScaleFilter(w, h); ImageProducer prod = new

Estimation of skeletal movement of human locomotion from body surface shapes using dynamic spatial video camera (DSVC) and 4D human model.

PubMed

Saito, Toshikuni; Suzuki, Naoki; Hattori, Asaki; Suzuki, Shigeyuki; Hayashibe, Mitsuhiro; Otake, Yoshito

2006-01-01

We have been developing a DSVC (Dynamic Spatial Video Camera) system to measure and observe human locomotion quantitatively and freely. A 4D (four-dimensional) human model with detailed skeletal structure, joint, muscle, and motor functionality has been built. The purpose of our research was to estimate skeletal movements from body surface shapes using DSVC and the 4D human model. For this purpose, we constructed a body surface model of a subject and resized the standard 4D human model to match with geometrical features of the subject's body surface model. Software that integrates the DSVC system and the 4D human model, and allows dynamic skeletal state analysis from body surface movement data was also developed. We practically applied the developed system in dynamic skeletal state analysis of a lower limb in motion and were able to visualize the motion using geometrically resized standard 4D human model.

Automotive Manufacturing Processes. Volume V - Manufacturing Processes and Equipment for the Mass Production and Assembly of Motor Vehicles

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and resizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pro...

Teaching Trends in Virtual Education: An Interpretative Approach

ERIC Educational Resources Information Center

Pando, Victor F.

2018-01-01

Based on the theoretical context of discussions about teaching trends in virtual education, particularly for higher education, this research develops an interpretation of some of these trends, resizing what was registered about it by other authors. To that end, a documentary study with an interpretative-analytical approach was carried out. The…

--No Title--

Science.gov Websites

; .fc-day-grid, .fc-scroller > .fc-time-grid { position: relative; /* re-scope all positions */ width -space: nowrap; overflow: hidden; } .fc-day-grid-event .fc-time { font-weight: bold; } /* resizer (cursor will be over the time grid */ } .fc-agenda-view .fc-day-grid .fc-row { min-height: 3em; /* all-day

Embedding Cognitive Systems into Systems Engineering Practice

DTIC Science & Technology

2008-12-01

application. Brahms, developed out of NASA Ames, is free for research and to the An Analysis of Alternatives consists of eight steps 1. Determine...said to look like a Star Trek ™ control panel. Fields dynamically resize when user click on them. This is helpful for those with vision degradation

Compressibility-aware media retargeting with structure preserving.

PubMed

Wang, Shu-Fan; Lai, Shang-Hong

2011-03-01

A number of algorithms have been proposed for intelligent image/video retargeting with image content retained as much as possible. However, they usually suffer from some artifacts in the results, such as ridge or structure twist. In this paper, we present a structure-preserving media retargeting technique that preserves the content and image structure as best as possible. Different from the previous pixel or grid based methods, we estimate the image content saliency from the structure of the content. A block structure energy is introduced with a top-down strategy to constrain the image structure inside to deform uniformly in either x or y direction. However, the flexibilities for retargeting are quite different for different images. To cope with this problem, we propose a compressibility assessment scheme for media retargeting by combining the entropies of image gradient magnitude and orientation distributions. Thus, the resized media is produced to preserve the image content and structure as best as possible. Our experiments demonstrate that the proposed method provides resized images/videos with better preservation of content and structure than those by the previous methods.

One Screen, Many Fingers: Young Children's Collaborative Literacy Play with Digital Puppetry Apps and Touchscreen Technologies

ERIC Educational Resources Information Center

Wohlwend, Karen E.

2015-01-01

This article examines the digital literacy practices that emerge when young children play together with digital apps on touchscreen devices. Children's collaborative composing with a digital puppetry app on a touchscreen--with many hands all busy dragging, resizing, and animating puppet characters, and many voices making sound effects, narrating,…

The Role of Visual Experience in Changing the Size of Objects in Imagery Processing

ERIC Educational Resources Information Center

Szubielska, Magdalena; Marek, Boguslaw

2015-01-01

Introduction: This paper investigates the question of whether or not subjects who are congenitally blind experience greater difficulties mentally in resizing images of objects than those who have low vision or are adventitiously blind. Methods: Two experiments were conducted--one in which subjects were asked to mentally enlarge objects they…

Tabular data and graphical images in support of the U.S. Geological Survey National Oil and Gas Assessment -- San Joaquin Basin (5010): Chapter 28 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

USGS Publications Warehouse

Klett, T.R.; Le, P.A.

2007-01-01

This chapter describes data used in support of the assessment process. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on this CD–ROM. Computers and software may import the data without transcription from the portable document format (.pdf) files of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

Chapter 2: Tabular Data and Graphical Images in Support of the U.S. Geological Survey National Oil and Gas Assessment - The Wind River Basin Province

USGS Publications Warehouse

Klett, T.R.; Le, P.A.

2007-01-01

This chapter describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on this CD-ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files) because of the number and variety of platforms and software available.

IMp: The customizable LEGO(®) Pinned Insect Manipulator.

PubMed

Dupont, Steen; Price, Benjamin; Blagoderov, Vladimir

2015-01-01

We present a pinned insect manipulator (IMp) constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble.

Raster Metafile And Raster Metafile Translator Programs

NASA Technical Reports Server (NTRS)

Randall, Donald P.; Gates, Raymond L.; Skeens, Kristi M.

1994-01-01

Raster Metafile (RM) computer program is generic raster-image-format program, and Raster Metafile Translator (RMT) program is assortment of software tools for processing images prepared in this format. Processing includes reading, writing, and displaying RM images. Such other image-manipulation features as minimal compositing operator and resizing option available under RMT command structure. RMT written in FORTRAN 77 and C language.

Population resizing on fitness improvement genetic algorithm to optimize promotion visit route based on android and google maps API

NASA Astrophysics Data System (ADS)

Listyorini, Tri; Muzid, Syafiul

2017-06-01

The promotion team of Muria Kudus University (UMK) has done annual promotion visit to several senior high schools in Indonesia. The visits were done to numbers of schools in Kudus, Jepara, Demak, Rembang and Purwodadi. To simplify the visit, each visit round is limited to 15 (fifteen) schools. However, the team frequently faces some obstacles during the visit, particularly in determining the route that they should take toward the targeted school. It is due to the long distance or the difficult route to reach the targeted school that leads to elongated travel duration and inefficient fuel cost. To solve these problems, the development of a certain application using heuristic genetic algorithm method based on the dynamic of population size or Population Resizing on Fitness lmprovement Genetic Algorithm (PRoFIGA), was done. This android-based application was developed to make the visit easier and to determine a shorter route for the team, hence, the visiting period will be effective and efficient. The result of this research was an android-based application to determine the shortest route by combining heuristic method and Google Maps Application Programming lnterface (API) that display the route options for the team.

Survey: interpolation methods for whole slide image processing.

PubMed

Roszkowiak, L; Korzynska, A; Zak, J; Pijanowska, D; Swiderska-Chadaj, Z; Markiewicz, T

2017-02-01

Evaluating whole slide images of histological and cytological samples is used in pathology for diagnostics, grading and prognosis . It is often necessary to rescale whole slide images of a very large size. Image resizing is one of the most common applications of interpolation. We collect the advantages and drawbacks of nine interpolation methods, and as a result of our analysis, we try to select one interpolation method as the preferred solution. To compare the performance of interpolation methods, test images were scaled and then rescaled to the original size using the same algorithm. The modified image was compared to the original image in various aspects. The time needed for calculations and results of quantification performance on modified images were also compared. For evaluation purposes, we used four general test images and 12 specialized biological immunohistochemically stained tissue sample images. The purpose of this survey is to determine which method of interpolation is the best to resize whole slide images, so they can be further processed using quantification methods. As a result, the interpolation method has to be selected depending on the task involving whole slide images. © 2016 The Authors Journal of Microscopy © 2016 Royal Microscopical Society.

Chapter 3: Tabular Data and Graphical Images in Support of the U.S. Geological Survey National Oil and Gas Assessment - Western Gulf Province, Smackover-Austin-Eagle Ford Composite Total Petroleum System (504702)

USGS Publications Warehouse

Klett, T.R.; Le, P.A.

2006-01-01

This chapter describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on this CD-ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

77 FR 46304 - Rimsulfuron; Pesticide Tolerances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

... types of entities not listed in this unit could also be affected. The North American Industrial... e-CFR site at http://ecfr.gpoaccess.gov/cgi/t/text/text-idx?&c=ecfr&tpl=/ecfrbrowse/Title40/40tab_02... petition submitted to the Agency. The Office of Management and Budget (OMB) has exempted these types of...

Case-Based Plan Recognition Using Action Sequence Graphs

DTIC Science & Technology

2014-10-01

resized as necessary. Similarly, trace- based reasoning (Zarka et al., 2013) and episode -based reasoning (Sánchez-Marré, 2005) store fixed-length...is a goal state of Π, where satisfies has the same semantics as originally laid out in Ghallab, Nau & Traverso (2004). Action 0 is ...Although there are syntactic similarities between planning encoding graphs and action sequence graphs, important semantic differences exist because the

Automated pupil remapping with binary optics

DOEpatents

Neal, Daniel R.; Mansell, Justin

1999-01-01

Methods and apparatuses for pupil remapping employing non-standard lenslet shapes in arrays; divergence of lenslet focal spots from on-axis arrangements; use of lenslet arrays to resize two-dimensional inputs to the array; and use of lenslet arrays to map an aperture shape to a different detector shape. Applications include wavefront sensing, astronomical applications, optical interconnects, keylocks, and other binary optics and diffractive optics applications.

IMp: The customizable LEGO® Pinned Insect Manipulator

PubMed Central

Dupont, Steen; Price, Benjamin; Blagoderov, Vladimir

2015-01-01

Abstract We present a pinned insect manipulator (IMp) constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble. PMID:25685035

Chapter 6. Tabular data and graphical images in support of the U.S. Geological Survey National Oil and Gas Assessment-East Texas basin and Louisiana-Mississippi salt basins provinces, Jurassic Smackover interior salt basins total petroleum system (504902), Travis Peak and Hosston formations.

USGS Publications Warehouse

,

2006-01-01

This chapter describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on the CD-ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

Chapter 3. Tabular data and graphical images in support of the U.S. Geological Survey National Oil and Gas Assessment--East Texas basin and Louisiana-Mississippi salt basins provinces, Jurassic Smackover Interior salt basins total petroleum system (504902), Cotton Valley group.

USGS Publications Warehouse

Klett, T.R.; Le, P.A.

2006-01-01

This chapter describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on the CD-ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

77 FR 74116 - Extension of Tolerances for Emergency Exemptions (Multiple Chemicals)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-13

.../text/text-idx?&c=ecfr&tpl=/ecfrbrowse/Title40/40tab_02.tpl . C. How can I file an objection or hearing... Management and Budget (OMB) has exempted these types of actions from review under Executive Order 12866.... 601 et seq.), do not apply. This final rule directly regulates growers, food processors, food handlers...

Automated pupil remapping with binary optics

DOEpatents

Neal, D.R.; Mansell, J.

1999-01-26

Methods and apparatuses are disclosed for pupil remapping employing non-standard lenslet shapes in arrays; divergence of lenslet focal spots from on-axis arrangements; use of lenslet arrays to resize two-dimensional inputs to the array; and use of lenslet arrays to map an aperture shape to a different detector shape. Applications include wavefront sensing, astronomical applications, optical interconnects, keylocks, and other binary optics and diffractive optics applications. 24 figs.

Seamless Integration of Desktop and Mobile Learning Experience through an Ontology-Based Adaptation Engine: Report of a Pilot-Project

ERIC Educational Resources Information Center

Mercurio, Marco; Torre, Ilaria; Torsani, Simone

2014-01-01

The paper describes a module within the distance language learning environment of the Language Centre at the Genoa University which adapts, through an ontology, learning activities to the device in use. Adaptation means not simply resizing a page but also the ability to transform the nature of a task so that it fits the device with the smallest…

Life Cycle Assessment of Vehicle Lightweighting: Novel Mathematical Methods to Estimate Use-Phase Fuel Consumption.

PubMed

Kim, Hyung Chul; Wallington, Timothy J; Sullivan, John L; Keoleian, Gregory A

2015-08-18

Lightweighting is a key strategy to improve vehicle fuel economy. Assessing the life-cycle benefits of lightweighting requires a quantitative description of the use-phase fuel consumption reduction associated with mass reduction. We present novel methods of estimating mass-induced fuel consumption (MIF) and fuel reduction values (FRVs) from fuel economy and dynamometer test data in the U.S. Environmental Protection Agency (EPA) database. In the past, FRVs have been measured using experimental testing. We demonstrate that FRVs can be mathematically derived from coast down coefficients in the EPA vehicle test database avoiding additional testing. MIF and FRVs calculated for 83 different 2013 MY vehicles are in the ranges 0.22-0.43 and 0.15-0.26 L/(100 km 100 kg), respectively, and increase to 0.27-0.53 L/(100 km 100 kg) with powertrain resizing to retain equivalent vehicle performance. We show how use-phase fuel consumption can be estimated using MIF and FRVs in life cycle assessments (LCAs) of vehicle lightweighting from total vehicle and vehicle component perspectives with, and without, powertrain resizing. The mass-induced fuel consumption model is illustrated by estimating lifecycle greenhouse gas (GHG) emission benefits from lightweighting a grille opening reinforcement component using magnesium or carbon fiber composite for 83 different vehicle models.

Tabular data and graphical images in support of the U.S. Geological Survey National Oil and Gas Assessment--San Juan Basin Province (5022): Chapter 7 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

USGS Publications Warehouse

Klett, T.R.; Le, P.A.

2013-01-01

This chapter describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on this CD–ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

All new custom path photo book creation

NASA Astrophysics Data System (ADS)

Wang, Wiley; Muzzolini, Russ

2012-03-01

In this paper, we present an all new custom path to allow consumers to have full control to their photos and the format of their books, while providing them with guidance to make their creation fast and easy. The users can choose to fully automate the initial creation, and then customize every page. The system manage many design themes along with numerous design elements, such as layouts, backgrounds, embellishments and pattern bands. The users can also utilize photos from multiple sources including their computers, Shutterfly accounts, Shutterfly Share sites and Facebook. The users can also use a photo as background, add, move and resize photos and text - putting what they want where they want instead of being confined to templates. The new path allows users to add embellishments anywhere in the book, and the high-performance platform can support up to 1,000 photos per book and up to 25 pictures per page. The path offers either Smart Autofill or Storyboard features allowing customers to populate their books with photos so they can add captions and customize the pages.

WOLF; automatic typing program

USGS Publications Warehouse

Evenden, G.I.

1982-01-01

A FORTRAN IV program for the Hewlett-Packard 1000 series computer provides for automatic typing operations and can, when employed with manufacturer's text editor, provide a system to greatly facilitate preparation of reports, letters and other text. The input text and imbedded control data can perform nearly all of the functions of a typist. A few of the features available are centering, titles, footnotes, indentation, page numbering (including Roman numerals), automatic paragraphing, and two forms of tab operations. This documentation contains both user and technical description of the program.

A Python library for FAIRer access and deposition to the Metabolomics Workbench Data Repository.

PubMed

Smelter, Andrey; Moseley, Hunter N B

2018-01-01

The Metabolomics Workbench Data Repository is a public repository of mass spectrometry and nuclear magnetic resonance data and metadata derived from a wide variety of metabolomics studies. The data and metadata for each study is deposited, stored, and accessed via files in the domain-specific 'mwTab' flat file format. In order to improve the accessibility, reusability, and interoperability of the data and metadata stored in 'mwTab' formatted files, we implemented a Python library and package. This Python package, named 'mwtab', is a parser for the domain-specific 'mwTab' flat file format, which provides facilities for reading, accessing, and writing 'mwTab' formatted files. Furthermore, the package provides facilities to validate both the format and required metadata elements of a given 'mwTab' formatted file. In order to develop the 'mwtab' package we used the official 'mwTab' format specification. We used Git version control along with Python unit-testing framework as well as continuous integration service to run those tests on multiple versions of Python. Package documentation was developed using sphinx documentation generator. The 'mwtab' package provides both Python programmatic library interfaces and command-line interfaces for reading, writing, and validating 'mwTab' formatted files. Data and associated metadata are stored within Python dictionary- and list-based data structures, enabling straightforward, 'pythonic' access and manipulation of data and metadata. Also, the package provides facilities to convert 'mwTab' files into a JSON formatted equivalent, enabling easy reusability of the data by all modern programming languages that implement JSON parsers. The 'mwtab' package implements its metadata validation functionality based on a pre-defined JSON schema that can be easily specialized for specific types of metabolomics studies. The library also provides a command-line interface for interconversion between 'mwTab' and JSONized formats in raw text and a variety of compressed binary file formats. The 'mwtab' package is an easy-to-use Python package that provides FAIRer utilization of the Metabolomics Workbench Data Repository. The source code is freely available on GitHub and via the Python Package Index. Documentation includes a 'User Guide', 'Tutorial', and 'API Reference'. The GitHub repository also provides 'mwtab' package unit-tests via a continuous integration service.

Overview of Necessary Modifications for Commercial Diesel Engines in Military Vehicles

DTIC Science & Technology

2012-01-20

TURBOCHARGING If the EGR system is removed from a COTS engine, changes to the turbocharger mostly likely will need to be made. Typically, EGR makes up...the compressor needs to compensate by drawing more fresh air. For optimum power and response, the turbocharger needs to be resized to handle the...7. Heywood, J, Internal Combustion Engine Fundamentals . New York : McGraw-Hill, 1988. 8. Brandt, A, Muzzell, P, Sattler, E, Likos, W, Military fuel

Some programming techniques for increasing program versatility and efficiency on CDC equipment

NASA Technical Reports Server (NTRS)

Tiffany, S. H.; Newsom, J. R.

1978-01-01

Five programming techniques used to decrease core and increase program versatility and efficiency are explained. The techniques are: (1) dynamic storage allocation, (2) automatic core-sizing and core-resizing, (3) matrix partitioning, (4) free field alphanumeric reads, and (5) incorporation of a data complex. The advantages of these techniques and the basic methods for employing them are explained and illustrated. Several actual program applications which utilize these techniques are described as examples.

Structural optimization of framed structures using generalized optimality criteria

NASA Technical Reports Server (NTRS)

Kolonay, R. M.; Venkayya, Vipperla B.; Tischler, V. A.; Canfield, R. A.

1989-01-01

The application of a generalized optimality criteria to framed structures is presented. The optimality conditions, Lagrangian multipliers, resizing algorithm, and scaling procedures are all represented as a function of the objective and constraint functions along with their respective gradients. The optimization of two plane frames under multiple loading conditions subject to stress, displacement, generalized stiffness, and side constraints is presented. These results are compared to those found by optimizing the frames using a nonlinear mathematical programming technique.

User's manual for the generalized computer program system. Open-channel flow and sedimentation, TABS-2. Main text

NASA Astrophysics Data System (ADS)

Thomas, W. A.; McAnally, W. H., Jr.

1985-07-01

TABS-2 is a generalized numerical modeling system for open-channel flows, sedimentation, and constituent transport. It consists of more than 40 computer programs to perform modeling and related tasks. The major modeling components--RMA-2V, STUDH, and RMA-4--calculate two-dimensional, depth-averaged flows, sedimentation, and dispersive transport, respectively. The other programs in the system perform digitizing, mesh generation, data management, graphical display, output analysis, and model interfacing tasks. Utilities include file management and automatic generation of computer job control instructions. TABS-2 has been applied to a variety of waterways, including rivers, estuaries, bays, and marshes. It is designed for use by engineers and scientists who may not have a rigorous computer background. Use of the various components is described in Appendices A-O. The bound version of the report does not include the appendices. A looseleaf form with Appendices A-O is distributed to system users.

Backward Registration Based Aspect Ratio Similarity (ARS) for Image Retargeting Quality Assessment.

PubMed

Zhang, Yabin; Fang, Yuming; Lin, Weisi; Zhang, Xinfeng; Li, Leida

2016-06-28

During the past few years, there have been various kinds of content-aware image retargeting operators proposed for image resizing. However, the lack of effective objective retargeting quality assessment metrics limits the further development of image retargeting techniques. Different from traditional Image Quality Assessment (IQA) metrics, the quality degradation during image retargeting is caused by artificial retargeting modifications, and the difficulty for Image Retargeting Quality Assessment (IRQA) lies in the alternation of the image resolution and content, which makes it impossible to directly evaluate the quality degradation like traditional IQA. In this paper, we interpret the image retargeting in a unified framework of resampling grid generation and forward resampling. We show that the geometric change estimation is an efficient way to clarify the relationship between the images. We formulate the geometric change estimation as a Backward Registration problem with Markov Random Field (MRF) and provide an effective solution. The geometric change aims to provide the evidence about how the original image is resized into the target image. Under the guidance of the geometric change, we develop a novel Aspect Ratio Similarity metric (ARS) to evaluate the visual quality of retargeted images by exploiting the local block changes with a visual importance pooling strategy. Experimental results on the publicly available MIT RetargetMe and CUHK datasets demonstrate that the proposed ARS can predict more accurate visual quality of retargeted images compared with state-of-the-art IRQA metrics.

Cost-efficient manufacturing of composite structures

NASA Technical Reports Server (NTRS)

Freeman, W. Tom; Davis, John G.; Johnston, Norman J.

1991-01-01

The Advanced Composites Technology (ACT) program is seeking research breakthroughs that will allow structures made of graphite epoxy materials to replace metals in the wings and fuselages of future aircrafts. NASA's goals are to reduce acquisition cost by 20 to 25 percent, structural weight for a resized aircraft by 40 to 50 percent, and the number of parts by half compared to current production aluminum aircraft. The innovative structural concepts, materials, and fabrication techniques emerging from the ACT program are described, and the relationship between aerospace developments and industrial, commercial, and sporting goods applications are discussed.

Preliminary structural sizing of a Mach 3.0 high-speed civil transport model

NASA Technical Reports Server (NTRS)

Blackburn, Charles L.

1992-01-01

An analysis has been performed pertaining to the structural resizing of a candidate Mach 3.0 High Speed Civil Transport (HSCT) conceptual design using a computer program called EZDESIT. EZDESIT is a computer program which integrates the PATRAN finite element modeling program to the COMET finite element analysis program for the purpose of calculating element sizes or cross sectional dimensions. The purpose of the present report is to document the procedure used in accomplishing the preliminary structural sizing and to present the corresponding results.

Inserting Phase Change Lines into Microsoft Excel® Graphs.

PubMed

Dubuque, Erick M

2015-10-01

Microsoft Excel® is a popular graphing tool used by behavior analysts to visually display data. However, this program is not always friendly to the graphing conventions used by behavior analysts. For example, adding phase change lines has typically been a cumbersome process involving the insertion of line objects that do not move when new data is added to a graph. The purpose of this article is to describe a novel way to add phase change lines that move when new data is added and when graphs are resized.

Edge directed image interpolation with Bamberger pyramids

NASA Astrophysics Data System (ADS)

Rosiles, Jose Gerardo

2005-08-01

Image interpolation is a standard feature in digital image editing software, digital camera systems and printers. Classical methods for resizing produce blurred images with unacceptable quality. Bamberger Pyramids and filter banks have been successfully used for texture and image analysis. They provide excellent multiresolution and directional selectivity. In this paper we present an edge-directed image interpolation algorithm which takes advantage of the simultaneous spatial-directional edge localization at the subband level. The proposed algorithm outperform classical schemes like bilinear and bicubic schemes from the visual and numerical point of views.

Inhibition of autophagy by TAB2 and TAB3.

PubMed

Criollo, Alfredo; Niso-Santano, Mireia; Malik, Shoaib Ahmad; Michaud, Mickael; Morselli, Eugenia; Mariño, Guillermo; Lachkar, Sylvie; Arkhipenko, Alexander V; Harper, Francis; Pierron, Gérard; Rain, Jean-Christophe; Ninomiya-Tsuji, Jun; Fuentes, José M; Lavandero, Sergio; Galluzzi, Lorenzo; Maiuri, Maria Chiara; Kroemer, Guido

2011-11-11

Autophagic responses are coupled to the activation of the inhibitor of NF-κB kinase (IKK). Here, we report that the essential autophagy mediator Beclin 1 and TGFβ-activated kinase 1 (TAK1)-binding proteins 2 and 3 (TAB2 and TAB3), two upstream activators of the TAK1-IKK signalling axis, constitutively interact with each other via their coiled-coil domains (CCDs). Upon autophagy induction, TAB2 and TAB3 dissociate from Beclin 1 and bind TAK1. Moreover, overexpression of TAB2 and TAB3 suppresses, while their depletion triggers, autophagy. The expression of the C-terminal domain of TAB2 or TAB3 or that of the CCD of Beclin 1 competitively disrupts the interaction between endogenous Beclin 1, TAB2 and TAB3, hence stimulating autophagy through a pathway that requires endogenous Beclin 1, TAK1 and IKK to be optimally efficient. These results point to the existence of an autophagy-stimulatory 'switch' whereby TAB2 and TAB3 abandon inhibitory interactions with Beclin 1 to engage in a stimulatory liaison with TAK1.

Inhibition of autophagy by TAB2 and TAB3

PubMed Central

Criollo, Alfredo; Niso-Santano, Mireia; Malik, Shoaib Ahmad; Michaud, Mickael; Morselli, Eugenia; Mariño, Guillermo; Lachkar, Sylvie; Arkhipenko, Alexander V; Harper, Francis; Pierron, Gérard; Rain, Jean-Christophe; Ninomiya-Tsuji, Jun; Fuentes, José M; Lavandero, Sergio; Galluzzi, Lorenzo; Maiuri, Maria Chiara; Kroemer, Guido

2011-01-01

Autophagic responses are coupled to the activation of the inhibitor of NF-κB kinase (IKK). Here, we report that the essential autophagy mediator Beclin 1 and TGFβ-activated kinase 1 (TAK1)-binding proteins 2 and 3 (TAB2 and TAB3), two upstream activators of the TAK1-IKK signalling axis, constitutively interact with each other via their coiled-coil domains (CCDs). Upon autophagy induction, TAB2 and TAB3 dissociate from Beclin 1 and bind TAK1. Moreover, overexpression of TAB2 and TAB3 suppresses, while their depletion triggers, autophagy. The expression of the C-terminal domain of TAB2 or TAB3 or that of the CCD of Beclin 1 competitively disrupts the interaction between endogenous Beclin 1, TAB2 and TAB3, hence stimulating autophagy through a pathway that requires endogenous Beclin 1, TAK1 and IKK to be optimally efficient. These results point to the existence of an autophagy-stimulatory ‘switch' whereby TAB2 and TAB3 abandon inhibitory interactions with Beclin 1 to engage in a stimulatory liaison with TAK1. PMID:22081109

A new approach to pre-processing digital image for wavelet-based watermark

NASA Astrophysics Data System (ADS)

Agreste, Santa; Andaloro, Guido

2008-11-01

The growth of the Internet has increased the phenomenon of digital piracy, in multimedia objects, like software, image, video, audio and text. Therefore it is strategic to individualize and to develop methods and numerical algorithms, which are stable and have low computational cost, that will allow us to find a solution to these problems. We describe a digital watermarking algorithm for color image protection and authenticity: robust, not blind, and wavelet-based. The use of Discrete Wavelet Transform is motivated by good time-frequency features and a good match with Human Visual System directives. These two combined elements are important for building an invisible and robust watermark. Moreover our algorithm can work with any image, thanks to the step of pre-processing of the image that includes resize techniques that adapt to the size of the original image for Wavelet transform. The watermark signal is calculated in correlation with the image features and statistic properties. In the detection step we apply a re-synchronization between the original and watermarked image according to the Neyman-Pearson statistic criterion. Experimentation on a large set of different images has been shown to be resistant against geometric, filtering, and StirMark attacks with a low rate of false alarm.

Structural arrangement trade study. Volume 3: Reusable Hydrogen Composite Tank System (RHCTS) and Graphite Composite Primary Structures (GCPS). Addendum

NASA Astrophysics Data System (ADS)

1995-03-01

This volume is the third of a 3 volume set that addresses the structural trade study plan that will identify the most suitable structural configuration for an SSTO winged vehicle capable of delivering 25,000 lbs to a 220 nm circular orbit at 51.6 deg inclination. The most suitable Reusable Hydrogen Composite Tank System (RHCTS), and Graphite Composite Tank System (GCPS) composite materials for intertank, wing and thrust structures are identified. Vehicle resizing charts, selection criteria and back-up charts, parametric costing approach and the finite element method analysis are discussed.

GelScape: a web-based server for interactively annotating, manipulating, comparing and archiving 1D and 2D gel images.

PubMed

Young, Nelson; Chang, Zhan; Wishart, David S

2004-04-12

GelScape is a web-based tool that permits facile, interactive annotation, comparison, manipulation and storage of protein gel images. It uses Java applet-servlet technology to allow rapid, remote image handling and image processing in a platform-independent manner. It supports many of the features found in commercial, stand-alone gel analysis software including spot annotation, spot integration, gel warping, image resizing, HTML image mapping, image overlaying as well as the storage of gel image and gel annotation data in compliance with Federated Gel Database requirements.

Selected topics from the structural acoustics program for the B-1 aircraft

NASA Technical Reports Server (NTRS)

Belcher, P. M.

1979-01-01

The major elements of the structural acoustics program for the B-1 aircraft are considered. Acoustic pressures measured at 280 sites on the surface of the vehicle were used to develop pressure models for a resizing of airframe components for aircraft No. 4 (A/C4). Acoustical fatigue design data for two dynamically complex structural configurations were acquired in laboratory programs, the conceptions for and executions of which detailed significant departures from the conventional. Design requirements for mechanical fasteners for configurations other than these two made use of analytical extensions of regrettably limited available information.

Structural arrangement trade study. Volume 3: Reusable Hydrogen Composite Tank System (RHCTS) and Graphite Composite Primary Structures (GCPS). Addendum

NASA Technical Reports Server (NTRS)

1995-01-01

This volume is the third of a 3 volume set that addresses the structural trade study plan that will identify the most suitable structural configuration for an SSTO winged vehicle capable of delivering 25,000 lbs to a 220 nm circular orbit at 51.6 deg inclination. The most suitable Reusable Hydrogen Composite Tank System (RHCTS), and Graphite Composite Tank System (GCPS) composite materials for intertank, wing and thrust structures are identified. Vehicle resizing charts, selection criteria and back-up charts, parametric costing approach and the finite element method analysis are discussed.

Weights assessment for orbit-on-demand vehicles

NASA Technical Reports Server (NTRS)

Macconochie, I. O.; Martin, J. A.; Breiner, C. A.; Cerro, J. A.

1985-01-01

Future manned, reusable earth-to-orbit vehicles may be required to reach orbit within hours or even minutes of a mission decision. A study has been conducted to consider vehicles with such a capability. In the initial phase of the study, 11 vehicles were sized for deployment of 5000 lbs to a polar orbit. From this matrix, two of the most promising concepts were resized for a modified mission and payload. A key feature of the study was the use of consistent mass estimating techniques for a broad range of concepts, allowing direct comparisons of sizes and weights.

jmzTab: a java interface to the mzTab data standard.

PubMed

Xu, Qing-Wei; Griss, Johannes; Wang, Rui; Jones, Andrew R; Hermjakob, Henning; Vizcaíno, Juan Antonio

2014-06-01

mzTab is the most recent standard format developed by the Proteomics Standards Initiative. mzTab is a flexible tab-delimited file that can capture identification and quantification results coming from MS-based proteomics and metabolomics approaches. We here present an open-source Java application programming interface for mzTab called jmzTab. The software allows the efficient processing of mzTab files, providing read and write capabilities, and is designed to be embedded in other software packages. The second key feature of the jmzTab model is that it provides a flexible framework to maintain the logical integrity between the metadata and the table-based sections in the mzTab files. In this article, as two example implementations, we also describe two stand-alone tools that can be used to validate mzTab files and to convert PRIDE XML files to mzTab. The library is freely available at http://mztab.googlecode.com. © 2014 The Authors PROTEOMICS Published by Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Craniomaxillofacial Surgical Assistance Workstation for Enhanced Single-Stage Reconstruction Using Patient-Specific Implants.

PubMed

Murphy, Ryan J; Liacouras, Peter C; Grant, Gerald T; Wolfe, Kevin C; Armand, Mehran; Gordon, Chad R

2016-11-01

Craniomaxillofacial reconstruction with patient-specific, customized craniofacial implants (CCIs) is ideal for skeletal defects involving areas of aesthetic concern-the non-weight-bearing facial skeleton, temporal skull, and/or frontal-forehead region. Results to date are superior to a variety of "off-the-shelf" materials, but require a protocol computed tomography scan and preexisting defect for computer-assisted design/computer-assisted manufacturing of the CCI. The authors developed a craniomaxillofacial surgical assistance workstation to address these challenges and intraoperatively guide CCI modification for an unknown defect size/shape. First, the surgeon designed an oversized CCI based on his/her surgical plan. Intraoperatively, the surgeon resected the bone and digitized the resection using a navigation pointer. Next, a projector displayed the limits of the craniofacial bone defect onto the prefabricated, oversized CCI for the size modification process; the surgeon followed the projected trace to modify the implant. A cadaveric study compared the standard technique (n = 1) to the experimental technique (n = 5) using surgical time and implant fit. The technology reduced the time and effort needed to resize the oversized CCI by an order of magnitude as compared with the standard manual resizing process. Implant fit was consistently better for the computer-assisted case compared with the control by at least 30%, requiring only 5.17 minutes in the computer-assisted cases compared with 35 minutes for the control. This approach demonstrated improvement in surgical time and accuracy of CCI-based craniomaxillofacial reconstruction compared with previously reported methods. The craniomaxillofacial surgical assistance workstation will provide craniofacial surgeons a computer-assisted technology for effective and efficient single-stage reconstruction when exact craniofacial bone defect sizes are unknown.

78 FR 35147 - Bacillus pumilus Strain BU F-33; Exemption From the Requirement of a Tolerance

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-12

...'s e-CFR site at http://www.ecfr.gov/cgi-bin/text-idx?&c=ecfr&tpl=/ecfrbrowse/Title40/40tab_02.tpl.... The Office of Management and Budget (OMB) has exempted these types of actions from review under... processors, food handlers, and food retailers, not States or tribes. As a result, this action does not alter...

Titania/CnTAB Nanoskeleton as adsorbent and photocatalyst for removal of alkylphenols dissolved in water.

PubMed

Sakai, Toshio; Da Loves, Albar; Okada, Tomohiko; Mishima, Shozi

2013-03-15

We report here on the removal of alkylphenols (phenol, 4-n-propylphenol, 4-n-heptylphenol and 4-nonylphenol) dissolved in water using the composite particles of nanocrystalline titania and alkyltrimethylammonium bromide (CnH2n+1N(CH3)3Br, CnTAB; n=12, 14, 16 and 18) (named as TiO2/CnTAB Nanoskeleton) as adsorbents and photocatalysts. In particular, the adsorption of alkylphenols onto TiO2/CnTAB Nanoskeleton in water was investigated in terms of hydrophobic interaction between alkylphenols and CnTAB, surface area, pore structure and crystal size of TiO2/CnTAB Nanoskeleton. We revealed that CnTAB incorporated in the TiO2/CnTAB Nanoskeleton promotes the adsorption of alkylphenols onto TiO2/CnTAB Nanoskeleton due to the hydrophobic interaction between alkylphenols and CnTAB. On the other hand, the surface area, pore structure and crystal size of TiO2/CnTAB Nanoskeleton did not affect the adsorption of alkylphenols onto TiO2/CnTAB Nanoskeleton. We also found that the alkylphenols dissolved in water were completely removed by the combination of adsorption and photocatalytic degradation by the TiO2/CnTAB Nanoskeleton under UV irradiation. These results prove that the TiO2/CnTAB Nanoskeleton acts as in tandem an adsorbent and a photocatalyst for removal of alkylphenols dissolved in water. Copyright © 2013 Elsevier B.V. All rights reserved.

Finite micro-tab system for load control on a wind turbine

NASA Astrophysics Data System (ADS)

Bach, A. B.; Lennie, M.; Pechlivanoglou, G.; Nayeri, C. N.; Paschereit, C. O.

2014-06-01

Finite micro-tabs have been investigated experimentally to evaluate the potential for load control on wind turbines. Two dimensional full span, as well as multiple finite tabs of various aspect ratios have been studied on an AH93W174 airfoil at different chord wise positions. A force balance was used to measure the aerodynamic loads. Furthermore, the wake vortex system consisting of the Karman vortex street as well as the tab tip vortices was analyzed with a 12-hole probe and hot wire anemometry. Finally, conventional oil paint as well as a quantitative digital flow analysis technique called SMARTviz were used to visualize the flow around the finite tab configurations. Results have shown that the devices are an effective solution to alleviate the airfoils overall load. The influence of the tab height, tab position as well as the finite tab aspect ratio on the lift and lift to drag ratio have been evaluated. It could be shown, that the lift difference can either be varied by changing the tab height as well as by altering the aspect ratio of the finite tabs. The drag of a two-dimensional flap is directly associated with the vortex street, while in the case of the finite tab, the solidity ratio of the tabs has the strongest effect on the drag. Therefore, the application of a finite tab system showed to improve the lift to drag ratio.

L∞-Optimal feedforward gust load alleviation design for a large blended wing body airliner

NASA Astrophysics Data System (ADS)

Wildschek, A.; Haniš, T.; Stroscher, F.

2013-12-01

The potential advantages of Blended Wing Body (BWB) aircraft in terms of fuel efficiency are opposed by technical challenges such as the alleviation of gust loads. Due to the low wing, loading gusts, generally, have a more severe impact on BWB aircraft than on conventional aircraft. This paper presents the design and optimization of a Gust Load Alleviation System (GLAS) for a large BWB airliner. Numerical simulations are performed with an aeroelastic model of the aircraft including GLAS in order to compute time series of modal displacements for deriving equivalent static load cases which are used for the resizing of the aircraft structure.

Finite-element reentry heat-transfer analysis of space shuttle Orbiter

NASA Technical Reports Server (NTRS)

Ko, William L.; Quinn, Robert D.; Gong, Leslie

1986-01-01

A structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat-transfer analysis of the space shuttle orbiter subjected to reentry aerodynamic heating. Three wing cross sections and one midfuselage cross section were selected for the thermal analysis. The predicted thermal protection system temperatures were found to agree well with flight-measured temperatures. The calculated aluminum structural temperatures also agreed reasonably well with the flight data from reentry to touchdown. The effects of internal radiation and of internal convection were found to be significant. The SPAR finite-element solutions agreed reasonably well with those obtained from the conventional finite-difference method.

Kelly and Lindgren conduct EMU Resize OPS

NASA Image and Video Library

2015-10-07

ISS045E050652 (10/07/2015) --- US astronauts Scott Kelly (bottom)and Kjell Lindgren (top) are counting down to a pair of spacewalks, now targeted for Oct. 28 and Nov. 6. The duo serviced their spacesuits replacing lithium batteries, checking their gloves and verifying power to video cameras. On the first spacewalk, the spacewalkers will lubricate the tip of the robotic arm Canadarm2, route power cables and place a thermal shroud over the Alpha Magnetic Spectrometer. During the second spacewalk, Kelly and Lindgren will refill coolant reservoirs and configure the port truss cooling system back to its original configuration after repair work completed back in 2012.

Flat tensile specimen design for advanced composites

NASA Technical Reports Server (NTRS)

Worthem, Dennis W.

1990-01-01

Finite element analyses of flat, reduced gage section tensile specimens with various transition region contours were performed. Within dimensional constraints, such as maximum length, tab region width, gage width, gage length, and minimum tab length, a transition contour radius of 41.9 cm produced the lowest stress values in the specimen transition region. The stresses in the transition region were not sensitive to specimen material properties. The stresses in the tab region were sensitive to specimen composite and/or tab material properties. An evaluation of stresses with different specimen composite and tab material combinations must account for material nonlinearity of both the tab and the specimen composite. Material nonlinearity can either relieve stresses in the composite under the tab or elevate them to cause failure under the tab.

Wind-Tunnel Investigation of the Effect of Tab Balance on Tab and Control-Surface Characteristics

NASA Technical Reports Server (NTRS)

Brewer, Jack D; Queijo, M J

1947-01-01

An investigation was conducted to furnish data on the effect of tab balance on tab and control-surface characteristics. The airfoil tested had a modified NACA 65(1)-012 contour with a plain flap having a chord equal to 25 percent of the wing chord and with a tab having a chord equal to 25 percent of the flap chord and having several nose shapes and overhang lengths. The results of the investigation indicated that, in general, tab balance affected tab hinge-moment characteristics in much the same manner that flap balance affects flap hinge-moment characteristics. A moderate amount of tab balance did not seem to have any adverse effect on flap hinge-moment characteristics.

Threaded Fastener Positive Anti-Rotation Locking Device

NASA Technical Reports Server (NTRS)

Hartman, Timm E. (Inventor); Hanlon, Casey (Inventor); Laidlaw, Mitchell (Inventor); Geck, Kellan (Inventor)

2015-01-01

An apparatus includes a shaft, a device, a fastener, and an anti-rotation clip. The shaft is configured for rotation. The device is mounted on, and surrounds at least a portion of, the shaft, and has first and second protrusions that are formed on one side and are spaced apart to define a tab space. The fastener is rotationally mounted relative to the shaft, and includes a tab slot formed in its outer surface that extends radially inwardly and is disposed radially inwardly of the tab space. The anti-rotation clip includes a main body portion and a head portion that has a first tab portion and a second tab portion. At least a portion the main body portion is disposed between the device and the fastener, the first tab is disposed in the tab space, and the second tab is disposed in the tab slot.

Experimental Investigation of a Preloaded Spring-tab Flutter Model

NASA Technical Reports Server (NTRS)

Smith, N H; Clevenson, S A; Barmby, J G

1947-01-01

An experimental investigation was made of a preloaded spring-tab flutter model to determine the effects on flutter speed of aspect ratio, tab frequency, and preloaded spring constant. The rudder was mass-balanced, and the flutter mode studied was essentially one of three degrees of freedom (fin bending coupled with rudder and tab oscillations). Inasmuch as the spring was preloaded, the tab-spring system was a nonlinear one. Frequency of the tab was the most significant parameter in this study, and an increase in flutter speed with increasing frequency is indicated. At a given frequency, the tab of high aspect ratio is shown to have a slightly lower flutter speed than the one of low aspect ratio. Because the frequency of the preloaded spring tab was found to vary radically with amplitude, the flutter speed decreased with increase in initial displacement of the tab.

An Experimental Study of the Near Field Region of a Free Jet with Passive Mixing Tabs

NASA Technical Reports Server (NTRS)

Bohl, D. G.; Foss, J. F.

1997-01-01

An experimental study was performed to determine the flow characteristics of a tabbed free jet. Results were acquired in the near field (nominally 2 tab widths upstream to 2 tab widths downstream of the exit plane) of a tabbed jet. Upstream pressure results showed static pressure distributions in both the x-and y-directions along the top surface of the tunnel. Hot-wire measurements showed rapid expansion of the core fluid into the ambient region. Two counter rotating regions of streamwise vorticity were shown on each side of the primary tab. An enhancement of the tabbed jet concept was proposed and tested. Specifically, two tabs, half the scale of the primary tab, were added to the primary tab to provide attachment surfaces for the normally occurring ejection of fluid. The secondary tabs caused a slight increase in the streamwise vorticity created from the upstream static pressure gradient while significantly increasing the re-oriented boundary layer vorticity. The combined pumping effect of the two counter rotating regions of vorticity caused a significant increase in the transport of the jet core fluid into the surrounding region.

Department of the Army Supply Bulletin, Army Medical Department Supply Information, SB8-75-S3

DTIC Science & Technology

2002-03-20

CITRATE INJ R 6505011282441 METHADONE HCL TABS100 R 6505011403199 ALPRAZOLAM TABS 100S Q 6505011403200 ALPRAZOLAM 1MG 100S Q 6505011403201... ALPRAZOLAM TABS 100S Q 6505011403202 ALPRAZOLAM TABS IS100 Q 6505011439269 ALPRAZOLAM TAB 100S Q 6505011461137 OXAZEPAM CAPS10MG100S Q 6505011468044...6505011932690 SUFENTANIL CITRATE IN R 6505011938484 MORPHINE SUL SOL120ML R 6505011947256 SUFENTANIL CITRATE IN R 6505011969501 ALPRAZOLAM TABS 500S Q

Experimental and computational investigation of lift-enhancing tabs on a multi-element airfoil

NASA Technical Reports Server (NTRS)

Ashby, Dale

1996-01-01

An experimental and computational investigation of the effect of lift enhancing tabs on a two-element airfoil was conducted. The objective of the study was to develop an understanding of the flow physics associated with lift enhancing tabs on a multi-element airfoil. A NACA 63(sub 2)-215 ModB airfoil with a 30 percent chord Fowler flap was tested in the NASA Ames 7 by 10 foot wind tunnel. Lift enhancing tabs of various heights were tested on both the main element and the flap for a variety of flap riggings. Computations of the flow over the two-element airfoil were performed using the two-dimensional incompressible Navier-Stokes code INS2D-UP. The computer results predict all of the trends in the experimental data quite well. When the flow over the flap upper surface is attached, tabs mounted at the main element trailing edge (cove tabs) produce very little change in lift. At high flap deflections. however, the flow over the flap is separated and cove tabs produce large increases in lift and corresponding reductions in drag by eliminating the separated flow. Cove tabs permit high flap deflection angles to be achieved and reduce the sensitivity of the airfoil lift to the size of the flap gap. Tabs attached to the flap training edge (flap tabs) are effective at increasing lift without significantly increasing drag. A combination of a cove tab and a flap tab increased the airfoil lift coefficient by 11 percent relative to the highest lift tab coefficient achieved by any baseline configuration at an angle of attack of zero percent and the maximum lift coefficient was increased by more than 3 percent. A simple analytic model based on potential flow was developed to provide a more detailed understanding of how lift enhancing tabs work. The tabs were modeled by a point vortex at the training edge. Sensitivity relationships were derived which provide a mathematical basis for explaining the effects of lift enhancing tabs on a multi-element airfoil. Results of the modeling effort indicate that the dominant effects of the tabs on the pressure distribution of each element of the airfoil can be captured with a potential flow model for cases with no flow separation.

Testing of the Trim Tab Parametric Model in NASA Langley's Unitary Plan Wind Tunnel

NASA Technical Reports Server (NTRS)

Murphy, Kelly J.; Watkins, Anthony N.; Korzun, Ashley M.; Edquist, Karl T.

2013-01-01

In support of NASA's Entry, Descent, and Landing technology development efforts, testing of Langley's Trim Tab Parametric Models was conducted in Test Section 2 of NASA Langley's Unitary Plan Wind Tunnel. The objectives of these tests were to generate quantitative aerodynamic data and qualitative surface pressure data for experimental and computational validation and aerodynamic database development. Six component force-and-moment data were measured on 38 unique, blunt body trim tab configurations at Mach numbers of 2.5, 3.5, and 4.5, angles of attack from -4deg to +20deg, and angles of sideslip from 0deg to +8deg. Configuration parameters investigated in this study were forebody shape, tab area, tab cant angle, and tab aspect ratio. Pressure Sensitive Paint was used to provide qualitative surface pressure mapping for a subset of these flow and configuration variables. Over the range of parameters tested, the effects of varying tab area and tab cant angle were found to be much more significant than varying tab aspect ratio relative to key aerodynamic performance requirements. Qualitative surface pressure data supported the integrated aerodynamic data and provided information to aid in future analyses of localized phenomena for trim tab configurations.

Identification and functional characterization of the TAB2 gene from Litopenaeus vannamei.

PubMed

Wang, Sheng; Li, Haoyang; Qian, Zhe; Song, Xuan; Zhang, Zijian; Zuo, Hongliang; Xu, Xiaopeng; Weng, Shaoping; He, Jianguo; Li, Chaozheng

2015-10-01

In Drosophila, TAB2, an important intermediate in the IMD signaling pathway, plays critical roles in the innate immune response in response to bacterial and viral infection. However, the role of TAB-related proteins in the immune response of shrimp has not yet been established. Here, we reported the identification of a TAB2-like gene in Litopenaeus vannamei designated as LvTAB2. The full-length cDNA of LvTAB2 was 2160 bp with an open reading frame of 1827 bp, which encoded a putative protein of 608 amino acids including a ubiquitin binding domain (CUE) at the N-terminal and a Zinc Finger domain (ZnF) at the C-terminus. Real-time RT-PCR analysis showed that LvTAB2 was expressed in all tested tissues and the expression levels of LvTAB2 in gills and hemocytes were positively induced in response to LPS, Vibrio parahemolyticus and White Spot Syndrome Virus (WSSV) challenges. Dual luciferase reporter assays demonstrated that LvTAB2 was able to induce the expression of antimicrobial peptide (AMP) genes, including Drosophila Attacin A and shrimp Penaeidins. Interestingly, over-expression of LvTAB2 could up-regulate the promoter activities of L. vannamei Vago1, Vago3 and Vago4 genes in S2 cells. To our knowledge, it was the first report that TAB2 participated in innate immune signaling to regulate the expression of Vago genes in invertebrates. Moreover, RNAi-mediated knockdown of LvTAB2 enhanced sensitivity of L. vannamei to Vibrio parahaemolyticus infection and caused elevated virus loads after WSSV infection. We suggested that the LvTAB2 may play important roles in the shrimp innate immunity. Copyright © 2015 Elsevier Ltd. All rights reserved.

An evolutionarily conserved motif in the TAB1 C-terminal region is necessary for interaction with and activation of TAK1 MAPKKK.

PubMed

Ono, K; Ohtomo, T; Sato, S; Sugamata, Y; Suzuki, M; Hisamoto, N; Ninomiya-Tsuji, J; Tsuchiya, M; Matsumoto, K

2001-06-29

TAK1, a member of the MAPKKK family, is involved in the intracellular signaling pathways mediated by transforming growth factor beta, interleukin 1, and Wnt. TAK1 kinase activity is specifically activated by the TAK1-binding protein TAB1. The C-terminal 68-amino acid sequence of TAB1 (TAB1-C68) is sufficient for TAK1 interaction and activation. Analysis of various truncated versions of TAB1-C68 defined a C-terminal 30-amino acid sequence (TAB1-C30) necessary for TAK1 binding and activation. NMR studies revealed that the TAB1-C30 region has a unique alpha-helical structure. We identified a conserved sequence motif, PYVDXA/TXF, in the C-terminal domain of mammalian TAB1, Xenopus TAB1, and its Caenorhabditis elegans homolog TAP-1, suggesting that this motif constitutes a specific TAK1 docking site. Alanine substitution mutagenesis showed that TAB1 Phe-484, located in the conserved motif, is crucial for TAK1 binding and activation. The C. elegans homolog of TAB1, TAP-1, was able to interact with and activate the C. elegans homolog of TAK1, MOM-4. However, the site in TAP-1 corresponding to Phe-484 of TAB1 is an alanine residue (Ala-364), and changing this residue to Phe abrogates the ability of TAP-1 to interact with and activate MOM-4. These results suggest that the Phe or Ala residue within the conserved motif of the TAB1-related proteins is important for interaction with and activation of specific TAK1 MAPKKK family members in vivo.

The H+/K+-ATPase inhibitory activities of Trametenolic acid B from Trametes lactinea (Berk.) Pat, and its effects on gastric cancer cells.

PubMed

Zhang, Qiaoyin; Huang, Nianyu; Wang, Junzhi; Luo, Huajun; He, Haibo; Ding, Mingruo; Deng, Wei-Qiao; Zou, Kun

2013-09-01

Trametenolic acid B (TAB), the bioactive component in the Trametes lactinea (Berk.) Pat, was reported to possess cytotoxic activities and thrombin inhibiting effects. This study was performed to investigate the effects of TAB on H(+)/K(+)-ATPase and gastric cancer. The H(+)/K(+)-ATPase inhibitory activity was determined by gastric parietal cells. Compared to the normal control group, TAB (10, 20, 40 and 80 μg/mL) inhibited the H(+)/K(+)-ATPase activity by 15.97, 16.96, 24.86 and 16.25%, respectively. In the study, 36 Kunming mice were randomly divided into six groups: control, model, TAB-L (TAB, 5 mg/kg/day, i.g.), TAB-M (TAB, 20 mg/kg/day, i.g.), TAB-H (TAB, 40 mg/kg/day, i.g.) and omeprazole (OL, 10 mg/kg/day, i.g.). All mice except the control group were administrated with anhydrous alcohol (5.0 mL/kg, i.g.) for induced gastric-ulcer 1h after the 5th day. At the same time, the control mice were given the same volume of physiological saline. After 4h, TAB was evaluated for H(+)/K(+)-ATPase inhibitory activities of ulcerative gaster, gastric ulcer index and ulcer inhibition. In vitro, the anti-proliferation effect of TAB to gastric cancer cell (HGC-27) in acid environment was detected by MTT, and the apoptosis morphological changes were also observed by Hoechst 33258 dye assay. The results indicated that TAB inhibited moderately H(+)/K(+)-ATPase activity in vitro. Compared to the model group, TAB showed anti-ulcer effects in gastric tissue with the dosages of 20 and 5 mg/kg in vivo. Apart from that, TAB could selectively inhibit gastric cancer cell viability and reduce cell apoptosis against HGC-27 cells at low doses in acid environment. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Parametric Study and Design of Tab Shape for Improving Aerodynamic Performance of Rotor Blade

NASA Astrophysics Data System (ADS)

Han, Jaeseong; Kwon, Oh Joon

2018-04-01

In the present study, the parametric study was performed to analyze the effect of the tab on the aerodynamic performance and characteristics of rotor blades. Also, the tab shape was designed to improve the aerodynamic performance of rotor blades. A computational fluid dynamics solver based on three-dimensional Reynolds averaged Navier-Stokes equation using an unstructured mesh was used for the parametric study and the tab design. For airfoils, the effect of length and angle of a tab was studied on the aerodynamic characteristics of airfoils. In addition, including those parameters, the effect of a span of a tab was studied for rotor blades in hovering flight. The results of the parametric study were analyzed in terms of change of the aerodynamic performance and characteristics to understand the effect of a tab. Considering the analysis, the design of tab shape was conducted to improve the aerodynamic performance of rotor blades. The simply attached tab to trailing edge of the rotor blades increases the thrust of the rotor blades without significant changing of aerodynamic characteristics of the rotor blades in hovering and forward flight.

Universal connectors for joining stringers

NASA Technical Reports Server (NTRS)

Harrison, Jr., Ernest (Inventor)

1987-01-01

This invention is a lightweight, universal connector that joins stringers at various angles. The connectors 10 are fabricated from fiber-epoxy resin strips that wrap around stringers 30 and have ends, tabs 16 and 18, which extend in one general direction. The inside surface of the first tab 16 lies on a plane defined by the stringers being joined, and the second tab 18 is separated from the first tab 16 by a distance equal to their thickness. Stringers 30 of different shapes and sizes are joined by alternately bonding the first tab 16 of one connector between the first 16 and second 18 tabs of another connector. Tee-joints are formed by using web elements 41 and 42 which each partially wrap around a stringer 3010 and have tabs 411 and 421 which are offset, and are bonded between tabs 16 and 18 of universal connectors 109 and 1010 bonded to another stringer 309. Sharp corners are trimmed from the tabs so that a gusset area remains between the stringers for support. Acute angle through obtuse angle joints are formed by trimming those edges of the tabs which lie against the stringers. A specific application of the invention is a Walker 60, utilized by handicapped individuals, fabricated from composite materials that is 40% lighter than similar metallic structures.

14 CFR 23.409 - Tabs.

Code of Federal Regulations, 2010 CFR

2010-01-01

...: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.409 Tabs. Control surface tabs must be designed for the most severe combination of airspeed and tab deflection likely to be obtained within the flight envelope for any usable loading condition. ...

Integrated Design and Engineering Analysis (IDEA) Environment - Propulsion Related Module Development and Vehicle Integration

NASA Technical Reports Server (NTRS)

Kamhawi, Hilmi N.

2013-01-01

This report documents the work performed during the period from May 2011 - October 2012 on the Integrated Design and Engineering Analysis (IDEA) environment. IDEA is a collaborative environment based on an object-oriented, multidisciplinary, distributed framework using the Adaptive Modeling Language (AML). This report will focus on describing the work done in the areas of: (1) Integrating propulsion data (turbines, rockets, and scramjets) in the system, and using the data to perform trajectory analysis; (2) Developing a parametric packaging strategy for a hypersonic air breathing vehicles allowing for tank resizing when multiple fuels and/or oxidizer are part of the configuration; and (3) Vehicle scaling and closure strategies.

Thermal response of Space Shuttle wing during reentry heating

NASA Technical Reports Server (NTRS)

Gong, L.; Ko, W. L.; Quinn, R. D.

1984-01-01

A structural performance and resizing (SPAR) finite element thermal analysis computer program was used in the heat transfer analysis of the space shuttle orbiter that was subjected to reentry aerodynamic heatings. One wing segment of the right wing (WS 240) and the whole left wing were selected for the thermal analysis. Results showed that the predicted thermal protection system (TPS) temperatures were in good agreement with the space transportation system, trajectory 5 (STS-5) flight-measured temperatures. In addition, calculated aluminum structural temperatures were in fairly good agreement with the flight data up to the point of touchdown. Results also showed that the internal free convection had a considerable effect on the change of structural temperatures after touchdown.

Applications of advanced electric/electronic technology to conventional aircraft

NASA Technical Reports Server (NTRS)

Heimbold, R. L.

1980-01-01

The desirability of seven advanced technologies as applied to three commercial aircraft of 1985 to 1995 was investigated. Digital fly by wire, multiplexing, ring laser gyro, integrated avionics, all electric airplane, electric load management, and fiber optics were considered for 500 passenger, 50 passenger, and 30 passenger aircraft. The major figure of merit used was Net Value of Technology based on procurement and operating cost over the life of the aircraft. An existing computer program, ASSET, was used to resize the aircraft and evalute fuel usage and maintenance costs for each candidate configuration. Conclusions were that, for the 500 passenger aircraft, all candidates had a worthwhile payoff with the all electric airplane having a large payoff.

Advanced composites structural concepts and materials technologies for primary aircraft structures: Design/manufacturing concept assessment

NASA Technical Reports Server (NTRS)

Chu, Robert L.; Bayha, Tom D.; Davis, HU; Ingram, J. ED; Shukla, Jay G.

1992-01-01

Composite Wing and Fuselage Structural Design/Manufacturing Concepts have been developed and evaluated. Trade studies were performed to determine how well the concepts satisfy the program goals of 25 percent cost savings, 40 percent weight savings with aircraft resizing, and 50 percent part count reduction as compared to the aluminum Lockheed L-1011 baseline. The concepts developed using emerging technologies such as large scale resin transfer molding (RTM), automatic tow placed (ATP), braiding, out-of-autoclave and automated manufacturing processes for both thermoset and thermoplastic materials were evaluated for possible application in the design concepts. Trade studies were used to determine which concepts carry into the detailed design development subtask.

Path planning for mobile robot using the novel repulsive force algorithm

NASA Astrophysics Data System (ADS)

Sun, Siyue; Yin, Guoqiang; Li, Xueping

2018-01-01

A new type of repulsive force algorithm is proposed to solve the problem of local minimum and the target unreachable of the classic Artificial Potential Field (APF) method in this paper. The Gaussian function that is related to the distance between the robot and the target is added to the traditional repulsive force, solving the problem of the goal unreachable with the obstacle nearby; variable coefficient is added to the repulsive force component to resize the repulsive force, which can solve the local minimum problem when the robot, the obstacle and the target point are in the same line. The effectiveness of the algorithm is verified by simulation based on MATLAB and actual mobile robot platform.

Low inductance busbar assembly

DOEpatents

Holbrook, Meghan Ann

2010-09-21

A busbar assembly for electrically coupling first and second busbars to first and second contacts, respectively, on a power module is provided. The assembly comprises a first terminal integrally formed with the first busbar, a second terminal integrally formed with the second busbar and overlapping the first terminal, a first bridge electrode having a first tab electrically coupled to the first terminal and overlapping the first and second terminals, and a second tab electrically coupled to the first contact, a second bridge electrode having a third tab electrically coupled to the second terminal, and overlapping the first and second terminals and the first tab, and a fourth tab electrically coupled to the second contact, and a fastener configured to couple the first tab to the first terminal, and the third tab to the second terminal.

Investigation of the Vortex Tab. M.S. Thesis

NASA Technical Reports Server (NTRS)

Hoffler, K. D.

1985-01-01

An investigation was made into the drag reduction capability of vortex tabs on delta wing vortex flaps. The vortex tab is an up-deflected leading edge portion of the vortex flap. Tab deflection augments vortex suction on the flap, thus improving its thrust, but the tab itself is drag producing. Whether a net improvement in the drag reduction can be obtained with vortex tabs, in comparison with plane vortex flaps of the same total area, was the objective of this investigation. Wind tunnel tests were conducted on two models, and analytical studies were performed on one of them using a free vortex sheet theory.

Color distribution of a shade guide in the value, chroma, and hue scale.

PubMed

Ahn, Jin-Soo; Lee, Yong-Keun

2008-07-01

Shade tabs in a shade guide are matched to teeth in the order of value, hue, and chroma; therefore, information on the distribution of shade tabs is essential for clinical application of a shade guide. However, there is limited information on the color distribution as sorted by these 3 parameters of a recently introduced shade guide. The purposes of this study were to determine the color distributions of tabs from a shade guide in the value (CIE L*), chroma (C*(ab)), and hue scale, and to determine the distribution of step intervals between adjacent tabs by value and chroma. The color of shade tabs (n=29) from a shade guide (Vitapan 3D-Master) was measured to determine the distribution of shade tabs by the value, chroma, hue angle, and CIE a* and b* values. The distribution of the ratios of the value and the chroma of each tab, when compared with the lowest value tab or the lowest chroma tab, was also determined. The data for each color parameter were analyzed by a 3-way ANOVA with the factors of value, chroma, and hue designations of the tabs (alpha=.05). The value, chroma, hue angle, and CIE a* and b* values were influenced by the value, chroma, and hue designations of shade tabs (P<.001). The distributions of the chroma of the tabs within the same value group were relatively ordered, but the values of different value groups overlapped in several instances. Distributions for the CIE a* and b* values reflected the chroma designations in each value group. In the same value group, L, M, and R hue designations corresponded with the manufacturer's stated hue, such as a yellow hue for the L designation and a red hue for the R designation. The distance in the value and chroma scales between adjacent tabs was not uniform. The color distribution of the Vitapan 3D-Master shade guide was more ordered than previously reported color distributions of other, traditional shade guides. However, the interval in the color parameters between adjacent tabs was not uniform; therefore, shade tabs spaced equally, according to the color parameters, should be studied based on the observer's response data.

Supersonic Aerodynamic Characteristics of Blunt Body Trim Tab Configurations

NASA Technical Reports Server (NTRS)

Korzun, Ashley M.; Murphy, Kelly J.; Edquist, Karl T.

2013-01-01

Trim tabs are aerodynamic control surfaces that can allow an entry vehicle to meet aerodynamic performance requirements while reducing or eliminating the use of ballast mass and providing a capability to modulate the lift-to-drag ratio during entry. Force and moment data were obtained on 38 unique, blunt body trim tab configurations in the NASA Langley Research Center Unitary Plan Wind Tunnel. The data were used to parametrically assess the supersonic aerodynamic performance of trim tabs and to understand the influence of tab area, cant angle, and aspect ratio. Across the range of conditions tested (Mach numbers of 2.5, 3.5, and 4.5; angles of attack from -4deg to +20deg; angles of sideslip from 0deg to +8deg), the effects of varying tab area and tab cant angle were found to be much more significant than effects from varying tab aspect ratio. Aerodynamic characteristics exhibited variation with Mach number and forebody geometry over the range of conditions tested. Overall, the results demonstrate that trim tabs are a viable approach to satisfy aerodynamic performance requirements of blunt body entry vehicles with minimal ballast mass. For a 70deg sphere-cone, a tab with 3% area of the forebody and canted approximately 35deg with no ballast mass was found to give the same trim aerodynamics as a baseline model with ballast mass that was 5% of the total entry mass.

76 FR 50405 - Airworthiness Directives; SOCATA Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-15

... elevator trim tab actuator jamming once the trim tab arrived to stop. The investigations conducted by the trim tab actuator manufacturer have shown that there was a discrepancy with PRECILEC manufacturing process of elevator trim tab actuator which caused this event. It has been determined as well that this...

Method for Fabricating Piezoelectric Polymer Acoustic Sensors

NASA Technical Reports Server (NTRS)

Hall, Thomas E., Jr. (Inventor); Bryant, Timothy D. (Inventor)

1998-01-01

A method for forming a sensor includes providing a first and a second film and bonding an internal connection tab there between. The internal connection tab is positioned between the inner surfaces of the first and second film. Then, a conductive adhesive is applied to either the tab or to the inner film surfaces such that the inner surfaces of the film and the tab are electrically connected. Finally, the films are pressed together to bond the film together with the internal connection tab in between.

14 CFR 25.407 - Trim tab effects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Trim tab effects. 25.407 Section 25.407... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads § 25.407 Trim tab effects. The effects of trim tabs on the control surface design conditions must be accounted for only where the...

14 CFR 25.407 - Trim tab effects.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Trim tab effects. 25.407 Section 25.407... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads § 25.407 Trim tab effects. The effects of trim tabs on the control surface design conditions must be accounted for only where the...

76 FR 30295 - Airworthiness Directives; SOCATA Model TBM 700 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-25

... case of elevator trim tab actuator jamming once the trim tab arrived to stop. The investigations conducted by the trim tab actuator manufacturer have shown that there was a discrepancy with PRECILEC manufacturing process of elevator trim tab actuator which caused this event. It has been determined as well that...

SWIMRT: A graphical user interface using the sliding window algorithm to construct a fluence map machine file

PubMed Central

Chow, James C.L.; Grigorov, Grigor N.; Yazdani, Nuri

2006-01-01

A custom‐made computer program, SWIMRT, to construct “multileaf collimator (MLC) machine” file for intensity‐modulated radiotherapy (IMRT) fluence maps was developed using MATLAB® and the sliding window algorithm. The user can either import a fluence map with a graphical file format created by an external treatment‐planning system such as Pinnacle3 or create his or her own fluence map using the matrix editor in the program. Through comprehensive calibrations of the dose and the dimension of the imported fluence field, the user can use associated image‐processing tools such as field resizing and edge trimming to modify the imported map. When the processed fluence map is suitable, a “MLC machine” file is generated for our Varian 21 EX linear accelerator with a 120‐leaf Millennium MLC. This machine file is transferred to the MLC console of the LINAC to control the continuous motions of the leaves during beam irradiation. An IMRT field is then irradiated with the 2D intensity profiles, and the irradiated profiles are compared to the imported or modified fluence map. This program was verified and tested using film dosimetry to address the following uncertainties: (1) the mechanical limitation due to the leaf width and maximum traveling speed, and (2) the dosimetric limitation due to the leaf leakage/transmission and penumbra effect. Because the fluence map can be edited, resized, and processed according to the requirement of a study, SWIMRT is essential in studying and investigating the IMRT technique using the sliding window algorithm. Using this program, future work on the algorithm may include redistributing the time space between segmental fields to enhance the fluence resolution, and readjusting the timing of each leaf during delivery to avoid small fields. Possible clinical utilities and examples for SWIMRT are given in this paper. PACS numbers: 87.53.Kn, 87.53.St, 87.53.Uv PMID:17533330

Development and wind tunnel evaluation of a shape memory alloy based trim tab actuator for a civil aircraft

NASA Astrophysics Data System (ADS)

Senthilkumar, P.; Jayasankar, S.; Satisha; Sateesh, V. L.; Kamaleshaiah, M. S.; Dayananda, G. N.

2013-09-01

This paper presents the development and wind tunnel evaluation of a shape memory alloy (SMA) based smart trim tab for a typical two seater civil aircraft. The SMA actuator was housed in the port side of the elevator for the purpose of actuating the trim tab. Wind tunnel tests were conducted on a full scale horizontal tail model with elevator and trim tab at free stream speeds of 25, 35 and 45 m s-1, and also for a number of deflections of the elevator (30° up, 0° neutral and 25° down) and trim tab (11° and 21° up and 15° and 31° down). To measure the hinge moment experienced by the trim tab under various test conditions, two miniaturized balances were designed and fabricated. A gain scheduled proportional integral (GSPI) controller was developed to control the SMA actuated smart trim tab. It was confirmed during the tests that the trim tab could be controlled at the desired position against the aerodynamic loads acting on it for the various test conditions.

Reversal in Spreading of a Tabbed Circular Jet Under Controlled Excitation

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.; Raman, G.

1997-01-01

Detailed flow field measurements have been carried out for a turbulent circular jet perturbed by tabs and artificial excitation. Two "delta tabs" were placed at the nozzle exit at diametricall opposite y locations. The excitation condition involved subharmonic resonance that manifested in a periodic vortex pairing in the near flow field. While the excitation and the tabs independently increased jet spreading, a combination of the two diminished the effect. The jet spreading was most pronounced with the tabs but was reduced when excitation was applied to the tabbed jet. The tabs generated streamwise vortex pairs that caused a lateral spreading of the jet in a direction perpendicular to the plane containing the tabs. ne excitation, on the other hand, organized the azimuthal vorticity into coherent ring structures whose evolution and pairing also increased entrainment by the jet. In the tabbed case, the excitation produced coherent azimuthal structures that were distorted and asymmetric in shape. The self-induction of these structures produced an effect that opposed the tendency for the lateral spreading of the streamwise vortex pairs. The passage of the distorted vortices, and their pairing, also had a cancellation effect on the time-averaged streamwise vorticity field. These led to the reduction in jet spreading.

14 CFR 23.407 - Trim tab effects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Trim tab effects. 23.407 Section 23.407... Loads § 23.407 Trim tab effects. The effects of trim tabs on the control surface design conditions must... deflections must correspond to the maximum degree of “out of trim” expected at the speed for the condition...

14 CFR 23.407 - Trim tab effects.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Trim tab effects. 23.407 Section 23.407... Loads § 23.407 Trim tab effects. The effects of trim tabs on the control surface design conditions must... deflections must correspond to the maximum degree of “out of trim” expected at the speed for the condition...

Direct molecular interactions between Beclin 1 and the canonical NFκB activation pathway.

PubMed

Niso-Santano, Mireia; Criollo, Alfredo; Malik, Shoaib Ahmad; Michaud, Michael; Morselli, Eugenia; Mariño, Guillermo; Lachkar, Sylvie; Galluzzi, Lorenzo; Maiuri, Maria Chaira; Kroemer, Guido

2012-02-01

General (macro)autophagy and the activation of NFκB constitute prominent responses to a large array of intracellular and extracellular stress conditions. The depletion of any of the three subunits of the inhibitor of NFκB (IκB) kinase (IKKα, IKKβ, IKKγ/NEMO), each of which is essential for the canonical NFκB activation pathway, limits autophagy induction by physiological or pharmacological triggers, while constitutive active IKK subunits suffice to stimulate autophagy. The activation of IKK usually relies on TGFβ-activated kinase 1 (TAK1), which is also necessary for the optimal induction of autophagy in multiple settings. TAK1 interacts with two structurally similar co-activators, TAK1-binding proteins 2 and 3 (TAB2 and TAB3). Importantly, in resting conditions both TAB2 and TAB3 bind the essential autophagic factor Beclin 1, but not TAK1. In response to pro-autophagic stimuli, TAB2 and TAB3 dissociate from Beclin 1 and engage in stimulatory interactions with TAK1. The inhibitory interaction between TABs and Beclin 1 is mediated by their coiled-coil domains (CCDs). Accordingly, the overexpression of either TAB2 or TAB3 CCD stimulates Beclin 1- and TAK1-dependent autophagy. These results point to the existence of a direct molecular crosstalk between the canonical NFκB activation pathway and the autophagic core machinery that guarantees the coordinated induction of these processes in response to stress.

Detecting Image Splicing Using Merged Features in Chroma Space

PubMed Central

Liu, Guangjie; Dai, Yuewei

2014-01-01

Image splicing is an image editing method to copy a part of an image and paste it onto another image, and it is commonly followed by postprocessing such as local/global blurring, compression, and resizing. To detect this kind of forgery, the image rich models, a feature set successfully used in the steganalysis is evaluated on the splicing image dataset at first, and the dominant submodel is selected as the first kind of feature. The selected feature and the DCT Markov features are used together to detect splicing forgery in the chroma channel, which is convinced effective in splicing detection. The experimental results indicate that the proposed method can detect splicing forgeries with lower error rate compared to the previous literature. PMID:24574877

Detecting image splicing using merged features in chroma space.

PubMed

Xu, Bo; Liu, Guangjie; Dai, Yuewei

2014-01-01

Image splicing is an image editing method to copy a part of an image and paste it onto another image, and it is commonly followed by postprocessing such as local/global blurring, compression, and resizing. To detect this kind of forgery, the image rich models, a feature set successfully used in the steganalysis is evaluated on the splicing image dataset at first, and the dominant submodel is selected as the first kind of feature. The selected feature and the DCT Markov features are used together to detect splicing forgery in the chroma channel, which is convinced effective in splicing detection. The experimental results indicate that the proposed method can detect splicing forgeries with lower error rate compared to the previous literature.

[Elderly human being with ostomy and environments of care: reflection on the perspective of complexity].

PubMed

Barros, Edaiane Joana Lima; Santos, Silvana Sidney Costa; Lunardi, Valéria Lerch; Lunardi Filho, Wilson Danilo

2012-01-01

This is discussion about the relationship between elderly human beings with ostomy and their environments care, under the perspective of Complexity Edgar Morin. An axis holds the reflection: environments of care for elderly humans with ostomy. In this sense, we present three types of environment that surround the context of elderly humans with ostomy: home environment, group environment and hospital environment. This brings, as a social contribution, a new look about resizing caring of elderly humans with ostomy in their environment. It is considered that the environment hosting this human being contains a diversity of feelings, emotions, experiences; it binds multiple meanings, from the Complexity perspective, about the relationship between the environment and the caring process.

Results of the Apogee-Raising Campaign of the Magnetospheric Multiscale Mission

NASA Technical Reports Server (NTRS)

Williams, Trevor; Ottenstein, Neil; Palmer, Eric J.; Hollister, Jacob

2017-01-01

This paper describes the apogee-raising campaign of the Magnetospheric Multiscale mission, where the spacecraft increased their apogee radii from 12 to 25 Earth radii in a total of 98 maneuvers. These maneuvers included an initial formation resize set to spread the spacecraft apart for safety, 32 apogee-raise delta-v maneuvers, their associated slews, four perigee-raise maneuvers and the associated slews, and finally a set of maneuvers to get back into formation. These activities were all accomplished successfully and on schedule with no anomalies, and at a fuel consumption somewhat less than predicted. As a result, MMS was set up ready to carry out in situ studies of magnetic reconnection in the magnetotail, with sufficient fuel remaining for a significant extended mission.

Application of Balancing Tabs to Ailerons

NASA Technical Reports Server (NTRS)

Sears, Richard I.

1942-01-01

Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.

Method of fabricating a solar cell array

DOEpatents

Lazzery, Angelo G.; Crouthamel, Marvin S.; Coyle, Peter J.

1982-01-01

A first set of pre-tabbed solar cells are assembled in a predetermined array with at least part of each tab facing upward, each tab being fixed to a bonding pad on one cell and abutting a bonding pad on an adjacent cell. The cells are held in place with a first vacuum support. The array is then inverted onto a second vacuum support which holds the tabs firmly against the cell pads they abut. The cells are exposed to radiation to melt and reflow the solder pads for bonding the tab portions not already fixed to bonding pads to these pads.

Thermal management for high-capacity large format Li-ion batteries

DOEpatents

Wang, Hsin; Kepler, Keith Douglas; Pannala, Sreekanth; Allu, Srikanth

2017-05-30

A lithium ion battery includes a cathode in electrical and thermal connection with a cathode current collector. The cathode current collector has an electrode tab. A separator is provided. An anode is in electrical and thermal connection with an anode current collector. The anode current collector has an electrode tab. At least one of the cathode current collector and the anode current collector comprises a thermal tab for heat transfer with the at least one current collector. The thermal tab is separated from the electrode tab. A method of operating a battery is also disclosed.

Shrimp TAB1 interacts with TAK1 and p38 and activates the host innate immune response to bacterial infection.

PubMed

Wang, Sheng; Li, Mengqiao; Yin, Bin; Li, Haoyang; Xiao, Bang; Lǚ, Kai; Huang, Zhijian; Li, Sedong; He, Jianguo; Li, Chaozheng

2017-08-01

Mammalian TAB1 has been previously identified as transforming growth factor-β (TGF-β)-activated kinase 1 (TAK1) binding protein, which functions as the activator of TAK1 and p38. This report, for the first time, identified and characterized the homolog of TAB1 in shrimp, to be specific, the homolog gene from Litopenaeus vannamei, containing a 1560-bp open reading frame (ORF) that encoded a putative protein of 519 amino acids with the conserved PP2Cc (Serine/threonine phosphatases, family 2C, catalytic) domain in N-terminal and a TAK1 binding motif in C-terminus, has been cloned and named LvTAB1. LvTAB1 was most abundant in gills and its expression could respond significantly to a series of stimuli, including LPS, Vibrio parahemolyticus and Staphylococcus aureus. Moreover, Co-immunoprecipitation (Co-IP) experiments showed that LvTAB1 could combine with LvTAK1 as well as Lvp38, two members of IMD-NF-κB/MAPK pathway, which meant LvTAB1 could have a role in regulating the activities of these kinases. Over-expression of LvTAB1 in drosophila S2 cells could improve the transcriptional levels of antimicrobial peptide genes (AMPs) such as Diptericin (Dpt), the hallmark of drosophila NF-κB activated genes, indicating its activation effect on NF-κB pathway. Furthermore, suppression of LvTAB1 expression in vivo by RNA-interference increased the sensibility of shrimps to V. parahaemolyticus infection, implying its protective role against bacterial infection. In conclusion, these results provide some insight into the function of LvTAB1 during bacterial infection. Copyright © 2017 Elsevier Ltd. All rights reserved.

Overexpression of a wheat (Triticum aestivum L.) bZIP transcription factor gene, TabZIP6, decreased the freezing tolerance of transgenic Arabidopsis seedlings by down-regulating the expression of CBFs.

PubMed

Cai, Wangting; Yang, Yaling; Wang, Weiwei; Guo, Guangyan; Liu, Wei; Bi, Caili

2018-03-01

The basic leucine zipper (bZIP) proteins play important roles against abiotic stress in plants, including cold stress. However, most bZIPs involved in plant freezing tolerance are positive regulators. Only a few bZIPs function negatively in cold stress response. In this study, TabZIP6, a Group C bZIP transcription factor gene from common wheat (Triticum aestivum L.), was cloned and characterized. The transcript of TabZIP6 was strongly induced by cold treatment (4 °C). TabZIP6 is a nuclear-localized protein with transcriptional activation activity. Arabidopsis plants overexpressing TabZIP6 showed decreased tolerance to freezing stress. Microarray as well as quantitative real-time PCR (qRT-PCR) analysis showed that CBFs and some key COR genes, including COR47 and COR15B, were down-regulated by cold treatment in TabZIP6-overexpressing Arabidopsis lines. TabZIP6 was capable of binding to the G-box motif and the CBF1 and CBF3 promoters in yeast cells. A yeast two-hybrid assay revealed that TabZIP6, as well as the other two Group S bZIP proteins involved in cold stress tolerance in wheat, Wlip19 and TaOBF1, can form homodimers by themselves and heterodimers with each other. These results suggest that TabZIP6 may function negatively in the cold stress response by binding to the promoters of CBFs, and thereby decreasing the expression of downstream COR genes in TabZIP6-overexpressing Arabidopsis seedlings. Copyright © 2018. Published by Elsevier Masson SAS.

Shade matching assisted by digital photography and computer software.

PubMed

Schropp, Lars

2009-04-01

To evaluate the efficacy of digital photographs and graphic computer software for color matching compared to conventional visual matching. The shade of a tab from a shade guide (Vita 3D-Master Guide) placed in a phantom head was matched to a second guide of the same type by nine observers. This was done for twelve selected shade tabs (tests). The shade-matching procedure was performed visually in a simulated clinic environment and with digital photographs, and the time spent for both procedures was recorded. An alternative arrangement of the shade tabs was used in the digital photographs. In addition, a graphic software program was used for color analysis. Hue, chroma, and lightness values of the test tab and all tabs of the second guide were derived from the digital photographs. According to the CIE L*C*h* color system, the color differences between the test tab and tabs of the second guide were calculated. The shade guide tab that deviated least from the test tab was determined to be the match. Shade matching performance by means of graphic software was compared with the two visual methods and tested by Chi-square tests (alpha= 0.05). Eight of twelve test tabs (67%) were matched correctly by the computer software method. This was significantly better (p < 0.02) than the performance of the visual shade matching methods conducted in the simulated clinic (32% correct match) and with photographs (28% correct match). No correlation between time consumption for the visual shade matching methods and frequency of correct match was observed. Shade matching assisted by digital photographs and computer software was significantly more reliable than by conventional visual methods.

Influence of surface layer removal of shade guide tabs on the measured color by spectrophotometer and spectroradiometer.

PubMed

Kim, Jin-Cheol; Yu, Bin; Lee, Yong-Keun

2008-12-01

To determine the changes in color parameters of Vitapan 3D-Master shade guide tabs by a spectrophotometer (SP) or a spectroradiometer (SR), and by the removal of the surface layer of the tabs that was performed to make a flat measuring surface for the SP color measurement. Color of the shade tabs was measured before and after removing the surface layer of the tabs using SP and SR. Correlations between the color parameters between the original (OR) and the surface layer removed (RM) tabs and between the SP and the SR measurements were determined (alpha=0.05). Based on SP, the lightness, chroma, CIE a* and b* values measured after the surface layer removal were higher than those of the original tabs except a few cases. Based on SR, the chroma and CIE a* and b* values measured after surface layer removal were higher than those of the original tabs except a few cases; however, in case of the lightness, the changes varied by the shade designation. Type of instrument influenced the changes in color parameters based on paired t-test (p<0.05). The color parameters of the OR and RM tabs showed correlations based on both SP and SR measurements (r=0.952-0.997 and p<0.01); however, color difference between the SP-RM and SR-OR tabs was in the range of 18.1-27.0 DeltaE(ab)(*) units (mean: 23.3+/-2.2). When the color of tooth-shaped objects is measured with a spectrophotometer or a spectroradiometer, measurement protocols should be specified because color difference by the surface layer removal and the instrument was high.

Structural and aerodynamic considerations of an active piezoelectric trailing-edge tab on a helicopter rotor

NASA Astrophysics Data System (ADS)

Murray, Gabriel Jon

This dissertation is concerned with an active tab for use on a rotorcraft for noise and vibration reduction. The tab is located at the trailing edge of the airfoil. The tab consists of a shim sandwiched by layers of the piezoelectric actuators, macro fiber composites, of varying length. This configuration is similar to a bimorph. The modus operandi is similar to that of a trailing edge flap. The actuators deform the tab, bending it to achieve a tip displacement. This provides a change in the lift, moment, and drag coefficients of the airfoil. By actuating the system at 3/rev to 5/rev, reductions in noise and vibration can be realized. The system was examined and designed around using the UH-60 Blackhawk as the model rotorcraft. The tab is envisioned to operate between 65% to 85% of the main rotor span. The tab's chordwise dimensions considered were 20% and 15% of the blade chord. In order to assess the potential of the tab to change the lift and moment coefficients of the airfoil-tab system, a steady computational fluid dynamics study was conducted. The results were generated via the University of Maryland's Transonic Unsteady Navier-Stokes code. Various tab deflection angles, Mach numbers, and angle-of-attack values were computed. These results were compared to a trailing edge flap of similar size. The comparison shows that the tab produces lift and moment increments similar to that of the trailing edge flap. The design of the tab---composed of both active piezoelectric actuators and passive materials---was conducted using finite element analysis. The objectives were to maximize the tip deflection due to the actuators, while minimizing the deformation due to inertial and aerodynamic forces and loads. The inertial loads (acceleration terms) come from both blade motion, such as flapping and pitch, as well as the rotation of the rotor (centrifugal force). All of these previously mentioned terms cause the tab to undergo undesirable deflections. The original concept consisted of a bimorph configuration with a single layer of macro fiber composite the entire length of the 20% chord tab. The final design has three, tapered actuator layers on either side of a shim. Also, the length of the tab was reduced to 15% of the chord. A multitude of designs were compared via their performance objectives as well as how the design variables changed performances relative to the objectives. The result of this detailed analysis was the selection of several configurations that were investigated in detail. With several designs selected, they formed the basis to build a prototype tab. This prototype was based on a 15% chord tab. Due to the available commercial actuator lengths, a two layer system was ultimately built. The tab tip displacement was measured with both static and harmonic inputs. Various input voltages, both with and without a DC offset, were tested, up to -500 V to 1500 V. The input frequency was varied between 0 Hz to 17.2 Hz. Also, a frequency response of the tab was generated. High voltage static tip displacement compares well with the expected result. The first bending natural frequency was measured at 138 Hz and compares well with the computed range of 135 Hz to 142 Hz, depending on bond layer thickness. The results of dynamic inputs uncovered an unexpected reduction in tip displacement of 60% to 65% of the static result, for high voltages. It is suspected that the actuator suffers from a time-dependent response, with quick initial displacement followed by a slow creeping to the final displacement value. This phenomena has also been observed in the literature, although it is not prevalent. Using the experiment as a guide to quantify the time-dependent behavior, the overall viability of the system is discussed. The maximum dynamic tip deflection (accounting for time-dependent behavior) of a 15% chord tab is 4°. The tab is able to generate lift coefficient increments up to 0.413 and moment increments of -0.068 for positive tab deflections. Deflections due to aerodynamic loads range from 0.3° to 2°. Deflections due to blade motions are less than 0.5° and due to the centrifugal force, 0.78°. This system can be stiffened, reducing the dynamic tip deflection to 3.25° and limiting the aerodynamic response to 1°. Overall, by designing the tab to modest deflections, moderate reductions in vibration are possible, but are limited by actuator authority. (Abstract shortened by UMI.)

Flight Measurements to Determine Effect of a Spring-Loaded Tab on Longitudinal Stability of an Airplane

NASA Technical Reports Server (NTRS)

Hunter, Paul A.; Reeder, John P.

1946-01-01

In conjunction with a program of research on the general problem of stability of airplanes in the climbing condition, tests have been made of a spring-loaded tb which. is referred to as a ?springy tab,? installed on the elevator of a low-wing scout bomber. The tab was arranged to deflect upward with decrease in speed which caused an increase in the pull force required to trim at low speeds and thereby increased the stick-free static longitudinal stability of the airplane. It was found that the springy tab would increase the stick-free stability in all flight conditions, would reduce the danger of inadvertent stalling because of the definite pull force required to stall the airplane with power on, would reduce the effect of center-of-gravity position on stick-free static stability, and would have little effect on the elevator stick forces in accelerated f11ght. Another advantage of the springy tab is that it might be used to provide almost any desired variation of elevator stick force with speed by adjusting the tab hinge-moment characteristics and the variation of spring moment with tab deflection. Unlike the bungee and the bobweight, the springy tab would provide stick-free static stability without requiring a pull force to hold the stick back while taxying. A device similar to the springy tab may be used on the rudder or ailerons to eliminate undesirable trim-force variations with speed.

Elliptic nozzle aspect ratio effect on controlled jet propagation

NASA Astrophysics Data System (ADS)

Aravindh Kumar, S. M.; Rathakrishnan, Ethirajan

2017-04-01

The present study deals with the control of a Mach 2 elliptic jet from a convergent-divergent elliptic nozzle of aspect ratio 4 using tabs at the nozzle exit. The experiments were carried out for rectangular and triangular tabs of the same blockage, placed along the major and minor axes of the nozzle exit, at different levels of nozzle expansion. The triangular tabs along the minor axis promoted superior mixing compared to the other controlled jets and caused substantial core length reduction at all the nozzle pressure ratios studied. The rectangular tabs along the minor axis caused core length reduction at all pressure ratios, but the values were minimal compared to that of triangular tabs along the minor axis. For all the test conditions, the mixing promotion caused by tabs along the major axis was inferior to that of tabs along the minor axis. The waves present in the core of controlled jets were visualized using a shadowgraph. Comparison of the present results with the results of a controlled Mach 2 elliptic jet of aspect ratio 2 (Aravindh Kumar and Sathakrishnan 2016 J. Propulsion Power 32 121-33, Aravindh Kumar and Rathakrishnan 2016 J. Aerospace Eng. at press (doi:10.1177/0954410016652921)) show that for all levels of expansion, the mixing effectiveness of triangular tabs along the minor axis of an aspect ratio 4 nozzle is better than rectangular or triangular tabs along the minor axis of an aspect ratio 2 nozzle.

Parametric Study of a Mixer/Ejector Nozzle with Mixing Enhancement Devices

NASA Technical Reports Server (NTRS)

DalBello, T.; Steffen, C. J., Jr.

2001-01-01

A numerical study employing a simplified model of the High Speed Civil Transport mixer/ejector nozzle has been conducted to investigate the effect of tabs (vortex generators) on the mixing process. More complete mixing of the primary and secondary flows within the confined ejector lowers peak exit velocity resulting in reduced jet noise. Tabs were modeled as vortex pairs and inserted into the computational model. The location, size, and number of tabs were varied and its effect on the mixing process is presented here both quantitatively and qualitatively. A baseline case (no tabs) along with six other cases involving two different vortex strengths at three different orientations have been computed and analyzed. The case with the highest vorticity (six vortices representing large tabs) gives the best mixing. It is shown that the influence of the vorticity acts primarily in the forward or middle portions of the duct, significantly alters the flow structure, and promotes some mixing in the lateral direction. Unmixed pockets were found at the top and bottom of the lobe, and more clever placement of tabs improved mixing in the vertical direction. The technique of replacing tabs with vortices shows promise as an efficient tool for quickly optimizing tab placement in lobed mixers.

Investigations on the stability, oscillation, and stress conditions of airplanes with tab control. Second partial report : application of the solutions obtained in the first partial report to tab-controlled airplanes.

NASA Technical Reports Server (NTRS)

Filzek, B

1949-01-01

The first partial report, FB 2000, contained a discussion of the derivation of the equations of motion and their solutions for a tab-controlled airplane; the results obtained there are now to be applied to the longitudinal motion of tab-controlled airplanes. In view of the abundance of structural factors and aerodynamic parameters, a general discussion of the problems is unfeasible. Thus it is demonstrated on the basis of examples what stability, oscillation, and stress conditions are to be expected for tab-controlled airplanes. (author)

Automated Interior Lighting Design Software for Base Civil Engineers.

DTIC Science & Technology

1987-09-01

1085 OPEN "I". #1, "A:MAINTCAT.INF" 1090 FOR ^=I TO 6 1i95 FOR B=l TO ? 1100 INPUT#I, MCAT $,A,B) 1105 NEXT B 1110 NEXT A 1115 CLOSE #1 112: REM 125...34 5415(1 PRINT 54155 FOR A=I TO 6 541,0 PRINT TAB󈧏 A; TAB(27) ’,A+61; TAB(45) ICAT$(A,I); TABt63) MCAT $(A,2, 54165 NEXT A 54170 PRINT :PRINT :PRINT...54305 54195 REM 542ry’) CLS 54205 PRINT :FRINT 54210 PRINT TAB(28) "MAINTENANCE CATEGORY EXAMPLE" 54215 PRINT 54:26 PRINT TAB(35i *CATEGORY " MCAT $(B

Examination of antimicrobial activity of selected non-antibiotic medicinal preparations.

PubMed

Kruszewska, Hanna; Zareba, Tomasz; Tyski, Stefan

2012-01-01

The aim of this study was to detect and characterize the antimicrobial activity of non-antibiotic drugs, selected from the pharmaceutical products analyzed during the state control performed in National Medicines Institute, Warszawa, Poland. In 2010, over 90 pharmaceutical preparations have been randomly chosen from different groups of drugs. The surveillance study was performed on standard ATCC microbial strains used for drug control: S. aureus, E. coli, P. aeruginosa and C. albicans. It was shown that the drugs listed below inhibited growth of at least one of the examined strains: Arketis 20 mg tab. (paroxetine), Buvasodil 150 mg tab. (buflomedile), Halidor 100 mg tab. (bencyclane), Hydroxyzinum espefa 25 mg tab. (hydroxyzine), Norifaz 35 mg tab. (risedronate), Strattera 60 mg cap. (atomoxetine), Tamiflu 75 mg tab. (oseltamivir), Valpro-ratiopharm Chrono 300 mg tab. with longer dissolution (valproate), Vetminth oral paste 24 g+3 g/100 mL (niclozamide, oxybendazol). Strattera cap. showed broad activity spectrum. It inhibited growth of all examined strains (MIC of active substance -- atomoxetine ranged between 2.6-13 mg/mL).

Effect of a delta tab on fine scale mixing in a turbulent two-stream shear layer

NASA Technical Reports Server (NTRS)

Foss, J. K.; Zaman, K. B. M. Q.

1996-01-01

The fine scale mixing produced by a delta tab in a shear layer has been studied experimentally. The tab was placed at the trailing edge of a splitter plate which produced a turbulent two-stream mixing layer. The tab apex tilted downstream and into the high speed stream. Hot-wire measurements in the 3-D space behind the tab detailed the three velocity components as well as the small scale population distributions. These small scale eddies, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. It was found that the small scale populations were greater in the shear region behind the tab, with the greatest increase occurring where the shear layer underwent a sharp turn. This location was near, but not coincident, with the core of the streamwise vortex, and away from the region exhibiting maximum turbulence intensity. Moreover, the tab increased the most probably frequency and strain rate of the small scales. It made the small scales smaller and more energetic.

Tabs and Accordions

EPA Pesticide Factsheets

While tabs and accordions were once common across the Web, we no longer recommend their use on EPA pages. Research has demonstrated that the use of tabs and accordions on websites can cause a number of search, access, and usability problems.

TabSQL: a MySQL tool to facilitate mapping user data to public databases.

PubMed

Xia, Xiao-Qin; McClelland, Michael; Wang, Yipeng

2010-06-23

With advances in high-throughput genomics and proteomics, it is challenging for biologists to deal with large data files and to map their data to annotations in public databases. We developed TabSQL, a MySQL-based application tool, for viewing, filtering and querying data files with large numbers of rows. TabSQL provides functions for downloading and installing table files from public databases including the Gene Ontology database (GO), the Ensembl databases, and genome databases from the UCSC genome bioinformatics site. Any other database that provides tab-delimited flat files can also be imported. The downloaded gene annotation tables can be queried together with users' data in TabSQL using either a graphic interface or command line. TabSQL allows queries across the user's data and public databases without programming. It is a convenient tool for biologists to annotate and enrich their data.

TabSQL: a MySQL tool to facilitate mapping user data to public databases

PubMed Central

2010-01-01

Background With advances in high-throughput genomics and proteomics, it is challenging for biologists to deal with large data files and to map their data to annotations in public databases. Results We developed TabSQL, a MySQL-based application tool, for viewing, filtering and querying data files with large numbers of rows. TabSQL provides functions for downloading and installing table files from public databases including the Gene Ontology database (GO), the Ensembl databases, and genome databases from the UCSC genome bioinformatics site. Any other database that provides tab-delimited flat files can also be imported. The downloaded gene annotation tables can be queried together with users' data in TabSQL using either a graphic interface or command line. Conclusions TabSQL allows queries across the user's data and public databases without programming. It is a convenient tool for biologists to annotate and enrich their data. PMID:20573251

Wheat bHLH-type transcription factor gene TabHLH1 is crucial in mediating osmotic stresses tolerance through modulating largely the ABA-associated pathway.

PubMed

Yang, Tongren; Yao, Sufei; Hao, Lin; Zhao, Yuanyuan; Lu, Wenjing; Xiao, Kai

2016-11-01

Wheat bHLH family gene TabHLH1 is responsive to drought and salt stresses, and it acts as one crucial regulator in mediating tolerance to aforementioned stresses largely through an ABA-associated pathway. Osmotic stresses are adverse factors for plant growth and crop productivity. In this study, we characterized TabHLH1, a gene encoding wheat bHLH-type transcription factor (TF) protein, in mediating plant adaptation to osmotic stresses. TabHLH1 protein contains a conserved basic-helix-loop-helix (bHLH) domain shared by its plant counterparts. Upon PEG-simulated drought stress, salt stress, and exogenous abscisic acid (ABA), the TabHLH1 transcripts in roots and leaves were induced. Under PEG-simulated drought stress and salt stress treatments, the tobacco seedlings with TabHLH1 overexpression exhibited improved growth and osmotic stress-associated traits, showing increased biomass and reduced leaf water loss rate (WLR) relative to wild type (WT). The transgenic lines also possessed promoted stomata closure under drought stress, salt stress, and exogenous ABA and increased proline and soluble sugar contents and reduced hydrogen peroxide (H 2 O 2 ) amount under osmotic stress conditions, indicating that TabHLH1-mediated osmolyte accumulation and cellular ROS homeostasis contributed to the drought stress and salt stress tolerance. NtPYL12 and NtSAPK2;1, the genes encoding ABA receptor and SnRK2 family kinase, respectively, showed up-regulated expression in lines overexpressing TabHLH1 under osmotic stress and exogenous ABA conditions; overexpression of them conferred plants modified stomata movement, leaf WLR, and growth feature under drought and high salinity, suggesting that these ABA-signaling genes are mediated by wheat TabHLH1 gene and involved in regulating plant responses to simulated drought and salt stresses. Our investigation indicates that the TabHLH1 gene plays critical roles in plant tolerance to osmotic stresses largely through an ABA-dependent pathway.

Lightness, chroma, and hue distributions of a shade guide as measured by a spectroradiometer.

PubMed

Lee, Yong-Keun; Yu, Bin; Lim, Ho-Nam

2010-09-01

The color attributes of commercially available shade guides have been measured by spectrophotometers (SP), which are designed to measure flat surfaces. However, there is limited information on the color distribution of shade guides as measured by spectroradiometers (SR), which are capable of measuring the color of curved surfaces. The purpose of this study was to determine the distributions of lightness (CIE L*) and chroma (C*(ab)) step intervals between adjacent shade tabs of a shade guide based on the lightness, chroma, and hue attributes measured by an SR. Lightness, chroma, hue angle, and CIE a* and b* values of the shade tabs (n=26) from a shade guide (Vitapan 3D-Master) were measured by an SR under daylight conditions. The distributions of the ratios in lightness and chroma of each tab compared with the lowest lightness tab or the lowest chroma tab were determined. The values for each color parameter were analyzed by a 3-way ANOVA with the factors of lightness, chroma, and hue designations of the shade tabs (alpha=.05). The chroma and CIE a* and b* values were influenced by the lightness, chroma, and hue designations of the shade tabs (P<.001); however, the lightness and hue angle were influenced by the lightness and hue designations, but not by the chroma designation. Distributions for the CIE a* and b* values, in each lightness group, corresponded with the chroma designation. However, the intervals in the lightness and chroma scales between adjacent tabs were not uniform. The intervals in the color parameters between adjacent shade tabs were not uniform based on SR measurements. Therefore, a shade guide in which shade tabs are more equally spaced by the color attributes, based on the values as measured by an SR along with observers' responses with respect to the equality of the intervals, should be devised. Copyright © 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Numerical investigation of multi-element airfoils

NASA Technical Reports Server (NTRS)

Cummings, Russell M.

1993-01-01

The flow over multi-element airfoils with flat-plate lift-enhancing tabs was numerically investigated. Tabs ranging in height from 0.25 percent to 1.25 percent of the reference airfoil chord were studied near the trailing edge of the main-element. This two-dimensional numerical simulation employed an incompressible Navier-Stokes solver on a structured, embedded grid topology. New grid refinements were used to improve the accuracy of the solution near the overlapping grid boundaries. The effects of various tabs were studied at a constant Reynolds number on a two-element airfoil with a slotted flap. Both computed and measured results indicated that a tab in the main-element cove improved the maximum lift and lift-to-drag ratio relative to the baseline airfoil without a tab. Computed streamlines revealed that the additional turning caused by the tab may reduce the amount of separated flow on the flap. A three-element airfoil was also studied over a range of Reynolds numbers. For the optimized flap rigging, the computed and measured Reynolds number effects were similar. When the flap was moved from the optimum position, numerical results indicated that a tab may help to reoptimize the airfoil to within 1 percent of the optimum flap case.

Lift-Enhancing Tabs on Multielement Airfoils

NASA Technical Reports Server (NTRS)

Ross, James C.; Storms, Bruce L.; Carrannanto, Paul G.

1995-01-01

The use of flat-plate tabs (similar to Gurney flaps) to enhance the lift of multielement airfoils is extended here by placing them on the pressure side and near the trailing edge of the main element rather than just on the furthest downstream wing element. The tabs studied range in height from 0.125 to 1.25% of the airfoil reference chord. In practice, such tabs would be retracted when the high-lift system is stowed. The effectiveness of the concept was demonstrated experimentally and computationally on a two-dimensional NACA 63(sub 2)-215 Mod B airfoil with a single-slotted, 30%-chord flap. Both the experiments and computations showed that the tabs significantly increase the lift at a given angle of attack and the maximum lift coefficient of the airfoil. The computational results showed that the increased lift was a result of additional turning of the flow by the tab that reduced or eliminated now separation on the flap. The best configuration tested, a 0.5%-chord tab placed 0.5% chord upstream of the trailing edge of the main element, increased the maximum lift coefficient of the airfoil by 12% and the maximum lift-to-drag ratio by 40%.

Jet Spreading Increase by Passive Control and Associated Performance Penalty

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

1999-01-01

This paper reviews the effects of 'screech', 'asymmetric nozzle shaping', 'tabs' and 'overexpansion' on the spreading of free jets. Corresponding thrust penalty for the tabs and overexpanded condition are also evaluated. The asymmetric shapes include rectangular ones with varying aspect ratio. Tabs investigated are triangular shaped 'delta-tabs' placed at the exit of a convergent circular nozzle. The effect of overexpansion is examined with circular convergent-divergent (C-D) nozzles. Tabs and overexpansion are found to yield the largest increase in jet spreading. Each, however, involves a performance penalty, i.e., a loss in thrust coefficient. Variation of the size of four delta-tabs show that there exists an optimum size for which the gain in jet spreading is the maximum per unit loss in thrust coefficient. With the C-D nozzles, the minimum in thrust coefficient is expected near the beginning of the overexpanded regime based on idealized flow calculations. The maximum increase in jet spreading, however, is found to occur at higher pressure ratios well into the overexpanded regime. The optimum benefit with the overexpanded flow, in terms of gain in spreading for unit penalty, is found to be comparable to the optimum tab case.

Experimental and Computational Investigation of Lift-Enhancing Tabs on a Multi-Element Airfoil

NASA Technical Reports Server (NTRS)

Ashby, Dale L.

1996-01-01

An experimental and computational investigation of the effect of lift-enhancing tabs on a two-element airfoil has been conducted. The objective of the study was to develop an understanding of the flow physics associated with lift-enhancing tabs on a multi-element airfoil. An NACA 63(2)-215 ModB airfoil with a 30% chord fowler flap was tested in the NASA Ames 7- by 10-Foot Wind Tunnel. Lift-enhancing tabs of various heights were tested on both the main element and the flap for a variety of flap riggings. A combination of tabs located at the main element and flap trailing edges increased the airfoil lift coefficient by 11% relative to the highest lift coefficient achieved by any baseline configuration at an angle of attack of 0 deg, and C(sub 1max) was increased by 3%. Computations of the flow over the two-element airfoil were performed using the two-dimensional incompressible Navier-Stokes code INS2D-UP. The computed results predicted all of the trends observed in the experimental data quite well. In addition, a simple analytic model based on potential flow was developed to provide a more detailed understanding of how lift-enhancing tabs work. The tabs were modeled by a point vortex at the air-foil or flap trailing edge. Sensitivity relationships were derived which provide a mathematical basis for explaining the effects of lift-enhancing tabs on a multi-element airfoil. Results of the modeling effort indicate that the dominant effects of the tabs on the pressure distribution of each element of the airfoil can be captured with a potential flow model for cases with no flow separation.

IIPImage: Large-image visualization

NASA Astrophysics Data System (ADS)

Pillay, Ruven

2014-08-01

IIPImage is an advanced high-performance feature-rich image server system that enables online access to full resolution floating point (as well as other bit depth) images at terabyte scales. Paired with the VisiOmatic (ascl:1408.010) celestial image viewer, the system can comfortably handle gigapixel size images as well as advanced image features such as both 8, 16 and 32 bit depths, CIELAB colorimetric images and scientific imagery such as multispectral images. Streaming is tile-based, which enables viewing, navigating and zooming in real-time around gigapixel size images. Source images can be in either TIFF or JPEG2000 format. Whole images or regions within images can also be rapidly and dynamically resized and exported by the server from a single source image without the need to store multiple files in various sizes.

TiConverter: A training image converting tool for multiple-point geostatistics

NASA Astrophysics Data System (ADS)

Fadlelmula F., Mohamed M.; Killough, John; Fraim, Michael

2016-11-01

TiConverter is a tool developed to ease the application of multiple-point geostatistics whether by the open source Stanford Geostatistical Modeling Software (SGeMS) or other available commercial software. TiConverter has a user-friendly interface and it allows the conversion of 2D training images into numerical representations in four different file formats without the need for additional code writing. These are the ASCII (.txt), the geostatistical software library (GSLIB) (.txt), the Isatis (.dat), and the VTK formats. It performs the conversion based on the RGB color system. In addition, TiConverter offers several useful tools including image resizing, smoothing, and segmenting tools. The purpose of this study is to introduce the TiConverter, and to demonstrate its application and advantages with several examples from the literature.

Automatic recognition of emotions from facial expressions

NASA Astrophysics Data System (ADS)

Xue, Henry; Gertner, Izidor

2014-06-01

In the human-computer interaction (HCI) process it is desirable to have an artificial intelligent (AI) system that can identify and categorize human emotions from facial expressions. Such systems can be used in security, in entertainment industries, and also to study visual perception, social interactions and disorders (e.g. schizophrenia and autism). In this work we survey and compare the performance of different feature extraction algorithms and classification schemes. We introduce a faster feature extraction method that resizes and applies a set of filters to the data images without sacrificing the accuracy. In addition, we have enhanced SVM to multiple dimensions while retaining the high accuracy rate of SVM. The algorithms were tested using the Japanese Female Facial Expression (JAFFE) Database and the Database of Faces (AT&T Faces).

Identifying images of handwritten digits using deep learning in H2O

NASA Astrophysics Data System (ADS)

Sadhasivam, Jayakumar; Charanya, R.; Kumar, S. Harish; Srinivasan, A.

2017-11-01

Automatic digit recognition is of popular interest today. Deep learning techniques make it possible for object recognition in image data. Perceiving the digit has turned into a fundamental part as far as certifiable applications. Since, digits are composed in various styles in this way to distinguish the digit it is important to perceive and arrange it with the assistance of machine learning methods. This exploration depends on supervised learning vector quantization neural system arranged under counterfeit artificial neural network. The pictures of digits are perceived, prepared and tried. After the system is made digits are prepared utilizing preparing dataset vectors and testing is connected to the pictures of digits which are separated to each other by fragmenting the picture and resizing the digit picture as needs be for better precision.

Duplex tab exhaust nozzle

NASA Technical Reports Server (NTRS)

Gutmark, Ephraim Jeff (Inventor); Martens, Steven (nmn) (Inventor)

2012-01-01

An exhaust nozzle includes a conical duct terminating in an annular outlet. A row of vortex generating duplex tabs are mounted in the outlet. The tabs have compound radial and circumferential aft inclination inside the outlet for generating streamwise vortices for attenuating exhaust noise while reducing performance loss.

The wheat transcription factor, TabHLH39, improves tolerance to multiple abiotic stressors in transgenic plants.

PubMed

Zhai, Yiqian; Zhang, Lichao; Xia, Chuan; Fu, Silu; Zhao, Guangyao; Jia, Jizeng; Kong, Xiuying

2016-05-13

Although bHLH transcription factors play important roles regulating plant development and abiotic stress response and tolerance, few functional studies have been performed in wheat. In this study, we isolated and characterized a bHLH gene, TabHLH39, from wheat. The TabHLH39 gene is located on wheat chromosome 5DL, and the protein localized to the nucleus and activated transcription. TabHLH39 showed variable expression in roots, stems, leaves, glumes, pistils and stamens and was induced by polyethylene glycol, salt and cold treatments. Further analysis revealed that TabHLH39 overexpression in Arabidopsis significantly enhanced tolerance to drought, salt and freezing stress during the seedling stage, which was also demonstrated by enhanced abiotic stress-response gene expression and changes to several physiological indices. Therefore, TabHLH39 has potential in transgenic breeding applications to improve abiotic stress tolerance in crops. Copyright © 2016 Elsevier Inc. All rights reserved.

The Infant Version of the Laboratory Temperament Assessment Battery (Lab-TAB): Measurement Properties and Implications for Concepts of Temperament

PubMed Central

Planalp, Elizabeth M.; Van Hulle, Carol; Gagne, Jeffrey R.; Goldsmith, H. Hill

2017-01-01

We describe large-sample research using the Infant Laboratory Temperament Assessment Battery (Lab-TAB; Goldsmith and Rothbart, 1996) in 1,076 infants at 6 and 12 months of age. The Lab-TAB was designed to assess temperament dimensions through a series of episodes that mimic everyday situations. Our goal is to provide guidelines for scoring Lab-TAB episodes to derive temperament composites. We also present a set of analyses examining mean differences and stability of temperament in early infancy, gender differences in infant temperament, as well as a validation of Lab-TAB episodes and composites with parent reported Infant Behavior Questionnaire (IBQ; Rothbart, 1981) scales. In general, laboratory observed temperament was only modestly related to parent reported temperament. However, temperament measures were significantly stable across time and several gender differences that align with previous research emerged. In sum, the Lab-TAB usefully assesses individual differences in infant emotionality. PMID:28596748

Deriving Childhood Temperament Measures from Emotion-eliciting Behavioral Episodes: Scale Construction and Initial Validation

PubMed Central

Gagne, Jeffrey R.; Van Hulle, Carol A.; Aksan, Nazan; Essex, Marilyn J.; Goldsmith, H. Hill

2010-01-01

The authors describe the development and initial validation of a home-based version of the Laboratory Temperament Assessment Battery (Lab-TAB), which was designed to assess childhood temperament using a comprehensive series of emotion-eliciting behavioral episodes. This paper provides researchers with general guidelines for assessing specific behaviors using the Lab-TAB and for forming behavioral composites that correspond to commonly researched temperament dimensions. We used mother ratings and independent post-visit observer ratings to provide validity evidence in a community sample of 4.5 year-old children. 12 Lab-TAB behavioral episodes were employed, yielding 24 within-episode temperament components that collapsed into 9 higher-level composites (Anger, Sadness, Fear, Shyness, Positive Expression, Approach, Active Engagement, Persistence, and Inhibitory Control). These dimensions of temperament are similar to those found in questionnaire-based assessments. Correlations among the 9 composites were low to moderate, suggesting relative independence. As expected, agreement between Lab-TAB measures and post-visit observer ratings was stronger than agreement between the Lab-TAB and mother questionnaire. However, for Active Engagement and Shyness, mother ratings did predict child behavior in the Lab-TAB quite well. Findings demonstrate the feasibility of emotion-eliciting temperament assessment methodologies, suggest appropriate methods for data aggregation into trait-level constructs, and set some expectations for associations between Lab-TAB dimensions and the degree of cross-method convergence between the Lab-TAB and other commonly used temperament assessments. PMID:21480723

Bioinformatic Analyses of Subgroup-A Members of the Wheat bZIP Transcription Factor Family and Functional Identification of TabZIP174 Involved in Drought Stress Response

PubMed Central

Li, Xueyin; Feng, Biane; Zhang, Fengjie; Tang, Yimiao; Zhang, Liping; Ma, Lingjian; Zhao, Changping; Gao, Shiqing

2016-01-01

Extensive studies in Arabidopsis and rice have demonstrated that Subgroup-A members of the bZIP transcription factor family play important roles in plant responses to multiple abiotic stresses. Although common wheat (Triticum aestivum) is one of the most widely cultivated and consumed food crops in the world, there are limited investigations into Subgroup A of the bZIP family in wheat. In this study, we performed bioinformatic analyses of the 41 Subgroup-A members of the wheat bZIP family. Phylogenetic and conserved motif analyses showed that most of the Subgroup-A bZIP proteins involved in abiotic stress responses of wheat, Arabidopsis, and rice clustered in Clade A1 of the phylogenetic tree, and shared a majority of conserved motifs, suggesting the potential importance of Clade-A1 members in abiotic stress responses. Gene structure analysis showed that TabZIP genes with close phylogenetic relationships tended to possess similar exon–intron compositions, and the positions of introns in the hinge regions of the bZIP domains were highly conserved, whereas introns in the leucine zipper regions were at variable positions. Additionally, eleven groups of homologs and two groups of tandem paralogs were also identified in Subgroup A of the wheat bZIP family. Expression profiling analysis indicated that most Subgroup-A TabZIP genes were responsive to abscisic acid and various abiotic stress treatments. TabZIP27, TabZIP74, TabZIP138, and TabZIP174 proteins were localized in the nucleus of wheat protoplasts, whereas TabZIP9-GFP fusion protein was simultaneously present in the nucleus, cytoplasm, and cell membrane. Transgenic Arabidopsis overexpressing TabZIP174 displayed increased seed germination rates and primary root lengths under drought treatments. Overexpression of TabZIP174 in transgenic Arabidopsis conferred enhanced drought tolerance, and transgenic plants exhibited lower water loss rates, higher survival rates, higher proline, soluble sugar, and leaf chlorophyll contents, as well as more stable osmotic potential under drought conditions. Additionally, overexpression of TabZIP174 increased the expression of stress-responsive genes (RD29A, RD29B, RAB18, DREB2A, COR15A, and COR47). The improved drought resistance might be attributed to the increased osmotic adjustment capacity. Our results indicate that TabZIP174 may participate in regulating plant response to drought stress and holds great potential for genetic improvement of abiotic stress tolerance in crops. PMID:27899926

In-flight tracking of helicopter rotor blades with tabs using shape memory alloy actuators

NASA Astrophysics Data System (ADS)

Epps, Jeanette Jo

The objective of this research is to develop a methodology to track helicopter rotor blades in-flight with tabs using shape memory alloy actuators. Tracking is required to reduce vibratory loads that are generated due to dissimilarity of blades. The research was conducted in two phases. The first phase involved a study on the thermo-mechanical behavior of shape memory alloys and the development of an analytical model to describe the behavior of the tab actuator (SMA-SMA actuator). The second phase of the research involved applying the knowledge of the SMA behavior to develop, construct and test a tab actuator to deflect a trailing-edge tab. In the first phase, four constitutive models for SMA were investigated and validated with test data. The models investigated were the Tanaka, Liang and Rogers, Brinson, and Boyd and Lagoudas models. These models were used to predict the quasi-static stress-strain-temperature behavior. All models showed acceptable correlation with test data. Then a constrained recovery model was developed for the case where the SMA wire is plastically deformed, clamped at both ends, and then heat activated. The Brinson model over-predicted the recovery stress-temperature behavior. The refined model developed in this dissertation showed acceptable correlation with test data. In the second phase of the research, a NACA 0012 blade section with a tab actuator embedded was constructed. The actuator was tested on bench-top as well as in an open-jet wind tunnel to determine the actuator performance under different flight conditions. This task also included building and testing a locking mechanism and a position feedback controller. It was shown that a 2-wire actuator, with all wires plastically elongated to 4.21% initially, is able to deflect the tab of a blade section sufficiently at a forward velocity of 120 ft/sec for angles of attack up to 15°. The tab deflected up 9.35° and deflected down 31°. A 5-wire actuator with all wires plastically deformed 2.43% initially was also tested in the open-jet wind tunnel. The tab deflected up 14° and down 11.5° at a forward velocity of 120 ft/sec and an angle of attack of 15°. The position feedback controller demonstrated its ability to track to a desired tab position in about 10 seconds. The locking mechanism showed its ability to lock the tab in position for the tab deflecting up during bench-top tests. (Abstract shortened by UMI.)

14 CFR 25.409 - Tabs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Tabs. 25.409 Section 25.409 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS... for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those...

14 CFR 25.409 - Tabs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Tabs. 25.409 Section 25.409 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS... for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those...

14 CFR 25.409 - Tabs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Tabs. 25.409 Section 25.409 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS... for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those...

14 CFR 25.409 - Tabs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tabs. 25.409 Section 25.409 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS... for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those...

14 CFR 25.409 - Tabs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Tabs. 25.409 Section 25.409 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS... for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those...

Trademark Status & Document Retrieval

Science.gov Websites

Policy & Law Reports TSDR now includes a Post Registration Maintenance Tab. When viewing a Registered mark, users will now find a new 3rd tab providing Post Registration information next to the " mark is not registered. TSDR now includes a Post Registration Maintenance Tab. When viewing a

77 FR 58330 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-20

... requires repetitive inspections of the aft attach lugs of the elevator tab control mechanisms, and replacement of any discrepant elevator tab control mechanism. Since we issued that AD, Boeing has developed a modification of the aft attach lugs of the elevator tab control mechanisms, which will adequately address the...

77 FR 45513 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-01

... prompted by a report of elevator vibration and bearing swage failures. This proposed AD would require, for... aft attach lugs for the elevator tab control mechanism, and replacement if necessary, and for other... elevator tab control mechanism, which could result in elevator and tab vibration. Consequent structural...

Application of spring tabs to elevator controls

NASA Technical Reports Server (NTRS)

Phillips, William H

1944-01-01

Equations are presented for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of a satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling or in flight at low airspeeds, and to prevent flutter. Examples are presented to show the design features of spring tabs required to solve these problems for airplanes of various sizes.

linkedISA: semantic representation of ISA-Tab experimental metadata.

PubMed

González-Beltrán, Alejandra; Maguire, Eamonn; Sansone, Susanna-Assunta; Rocca-Serra, Philippe

2014-01-01

Reporting and sharing experimental metadata- such as the experimental design, characteristics of the samples, and procedures applied, along with the analysis results, in a standardised manner ensures that datasets are comprehensible and, in principle, reproducible, comparable and reusable. Furthermore, sharing datasets in formats designed for consumption by humans and machines will also maximize their use. The Investigation/Study/Assay (ISA) open source metadata tracking framework facilitates standards-compliant collection, curation, visualization, storage and sharing of datasets, leveraging on other platforms to enable analysis and publication. The ISA software suite includes several components used in increasingly diverse set of life science and biomedical domains; it is underpinned by a general-purpose format, ISA-Tab, and conversions exist into formats required by public repositories. While ISA-Tab works well mainly as a human readable format, we have also implemented a linked data approach to semantically define the ISA-Tab syntax. We present a semantic web representation of the ISA-Tab syntax that complements ISA-Tab's syntactic interoperability with semantic interoperability. We introduce the linkedISA conversion tool from ISA-Tab to the Resource Description Framework (RDF), supporting mappings from the ISA syntax to multiple community-defined, open ontologies and capitalising on user-provided ontology annotations in the experimental metadata. We describe insights of the implementation and how annotations can be expanded driven by the metadata. We applied the conversion tool as part of Bio-GraphIIn, a web-based application supporting integration of the semantically-rich experimental descriptions. Designed in a user-friendly manner, the Bio-GraphIIn interface hides most of the complexities to the users, exposing a familiar tabular view of the experimental description to allow seamless interaction with the RDF representation, and visualising descriptors to drive the query over the semantic representation of the experimental design. In addition, we defined queries over the linkedISA RDF representation and demonstrated its use over the linkedISA conversion of datasets from Nature' Scientific Data online publication. Our linked data approach has allowed us to: 1) make the ISA-Tab semantics explicit and machine-processable, 2) exploit the existing ontology-based annotations in the ISA-Tab experimental descriptions, 3) augment the ISA-Tab syntax with new descriptive elements, 4) visualise and query elements related to the experimental design. Reasoning over ISA-Tab metadata and associated data will facilitate data integration and knowledge discovery.

Total Petroleum Systems and Geologic Assessment of Oil and Gas Resources in the Powder River Basin Province, Wyoming and Montana

USGS Publications Warehouse

Anna, L.O.

2009-01-01

The U.S. Geological Survey completed an assessment of the undiscovered oil and gas potential of the Powder River Basin in 2006. The assessment of undiscovered oil and gas used the total petroleum system concept, which includes mapping the distribution of potential source rocks and known petroleum accumulations and determining the timing of petroleum generation and migration. Geologically based, it focuses on source and reservoir rock stratigraphy, timing of tectonic events and the configuration of resulting structures, formation of traps and seals, and burial history modeling. The total petroleum system is subdivided into assessment units based on similar geologic characteristics and accumulation and petroleum type. In chapter 1 of this report, five total petroleum systems, eight conventional assessment units, and three continuous assessment units were defined and the undiscovered oil and gas resources within each assessment unit quantitatively estimated. Chapter 2 describes data used in support of the process being applied by the U.S. Geological Survey (USGS) National Oil and Gas Assessment (NOGA) project. Digital tabular data used in this report and archival data that permit the user to perform further analyses are available elsewhere on this CD-ROM. Computers and software may import the data without transcription from the Portable Document Format files (.pdf files) of the text by the reader. Because of the number and variety of platforms and software available, graphical images are provided as .pdf files and tabular data are provided in a raw form as tab-delimited text files (.tab files).

A Novel Wheat C-bZIP Gene, TabZIP14-B, Participates in Salt and Freezing Tolerance in Transgenic Plants

PubMed Central

Zhang, Lina; Zhang, Lichao; Xia, Chuan; Gao, Lifeng; Hao, Chenyang; Zhao, Guangyao; Jia, Jizeng; Kong, Xiuying

2017-01-01

The group C-bZIP transcription factors (TFs) are involved in diverse biological processes, such as the regulation of seed storage protein (SSP) production and the responses to pathogen challenge and abiotic stress. However, our knowledge of the abiotic functions of group C-bZIP genes in wheat remains limited. Here, we present the function of a novel TabZIP14-B gene in wheat. This gene belongs to the group C-bZIP TFs and contains six exons and five introns; three haplotypes were identified among accessions of tetraploid and hexaploid wheat. A subcellular localization analysis indicated that TabZIP14-B was targeted to the nucleus of tobacco epidermal cells. A transactivation assay demonstrated that TabZIP14-B showed transcriptional activation ability and was capable of binding the abscisic acid (ABA) responsive element (ABRE) in yeast. RT-qPCR revealed that TabZIP14-B was expressed in the roots, stems, leaves, and young spikes and was up-regulated by exogenous ABA, salt, low-temperature, and polyethylene glycol (PEG) stress treatments. Furthermore, Arabidopsis plants overexpressing TabZIP14-B exhibited enhanced tolerance to salt, freezing stresses and ABA sensitivity. Overexpression of TabZIP14-B resulted in increased expression of the AtRD29A, AtCOR47, AtRD20, AtGSTF6, and AtRAB18 genes and changes in several physiological characteristics. These results suggest that TabZIP14-B could function as a positive regulator in mediating the abiotic stress response. PMID:28536588

78 FR 2910 - Airworthiness Directives; GROB-WERKE Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-15

... condition on an aviation product. The MCAI describes the unsafe condition as cracks in the elevator trim tab... for the specified products. The MCAI states: On several Grob G 115 aeroplanes, elevator trim tab arms... the rear edge of the trim tab arm. This condition, if not detected and corrected, could lead to...

TAB2 Is Essential for Prevention of Apoptosis in Fetal Liver but Not for Interleukin-1 Signaling

PubMed Central

Sanjo, Hideki; Takeda, Kiyoshi; Tsujimura, Tohru; Ninomiya-Tsuji, Jun; Matsumoto, Kunihiro; Akira, Shizuo

2003-01-01

The proinflammatory cytokine interleukin-1 (IL-1) transmits a signal via several critical cytoplasmic proteins such as MyD88, IRAKs and TRAF6. Recently, serine/threonine kinase TAK1 and TAK1 binding protein 1 and 2 (TAB1/2) have been identified as molecules involved in IL-1-induced TRAF6-mediated activation of AP-1 and NF-κB via mitogen-activated protein (MAP) kinases and IκB kinases, respectively. However, their physiological functions remain to be clarified. To elucidate their roles in vivo, we generated TAB2-deficient mice. The TAB2 deficiency was embryonic lethal due to liver degeneration and apoptosis. This phenotype was similar to that of NF-κB p65-, IKKβ-, and NEMO/IKKγ-deficient mice. However, the IL-1-induced activation of NF-κB and MAP kinases was not impaired in TAB2-deficient embryonic fibroblasts. These findings demonstrate that TAB2 is essential for embryonic development through prevention of liver apoptosis but not for the IL-1 receptor-mediated signaling pathway. PMID:12556483

Photocontrol of Voltage-Gated Ion Channel Activity by Azobenzene Trimethylammonium Bromide in Neonatal Rat Cardiomyocytes

PubMed Central

Frolova, Sheyda R.; Gaiko, Olga; Tsvelaya, Valeriya A.; Pimenov, Oleg Y.; Agladze, Konstantin I.

2016-01-01

The ability of azobenzene trimethylammonium bromide (azoTAB) to sensitize cardiac tissue excitability to light was recently reported. The dark, thermally relaxed trans- isomer of azoTAB suppressed spontaneous activity and excitation propagation speed, whereas the cis- isomer had no detectable effect on the electrical properties of cardiomyocyte monolayers. As the membrane potential of cardiac cells is mainly controlled by activity of voltage-gated ion channels, this study examined whether the sensitization effect of azoTAB was exerted primarily via the modulation of voltage-gated ion channel activity. The effects of trans- and cis- isomers of azoTAB on voltage-dependent sodium (INav), calcium (ICav), and potassium (IKv) currents in isolated neonatal rat cardiomyocytes were investigated using the whole-cell patch-clamp technique. The experiments showed that azoTAB modulated ion currents, causing suppression of sodium (Na+) and calcium (Ca2+) currents and potentiation of net potassium (K+) currents. This finding confirms that azoTAB-effect on cardiac tissue excitability do indeed result from modulation of voltage-gated ion channels responsible for action potential. PMID:27015602

Tab2, a novel recombinant polypeptide tag offering sensitive and specific protein detection and reliable affinity purification.

PubMed

Crusius, Kerstin; Finster, Silke; McClary, John; Xia, Wei; Larsen, Brent; Schneider, Douglas; Lu, Hong-Tao; Biancalana, Sara; Xuan, Jian-Ai; Newton, Alicia; Allen, Debbie; Bringmann, Peter; Cobb, Ronald R

2006-10-01

The detection and purification of proteins are often time-consuming and frequently involve complicated protocols. The addition of a peptide tag to recombinant proteins can make this process more efficient. Many of the commonly used tags, such as Flagtrade mark, Myc, HA and V5 are recognized by specific monoclonal antibodies and therefore, allow immunoaffinity-based purification. Enhancing the current scope of flexibility in using diverse peptide tags, we report here the development of a novel, short polypeptide tag (Tab2) for detection and purification of recombinant proteins. The Tab2 epitope corresponds to the NH2-terminal seven amino acid residues of human TGFalpha. A monoclonal anti-Tab2 antibody was raised and characterized. To investigate the potential of this peptide sequence as a novel tag for recombinant proteins, we expressed several different recombinant proteins containing this tag in E. coli, baculovirus, and mammalian cells. The data presented demonstrates the Tab2 tag-anti-Tab2 antibody combination is a reliable tool enabling specific Western blot detection, FACS analysis, and immunoprecipitation as well as non-denaturing protein affinity purification.

25 CFR 542.8 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2010 CFR

2010-04-01

... the accuracy of the ending balance in the pull tab control by reconciling the pull tabs on hand. (6) A.... (g) Standards for statistical reports. (1) Records shall be maintained, which include win, write (sales), and a win-to-write hold percentage as compared to the theoretical hold percentage derived from...

75 FR 60659 - Airworthiness Directives; 328 Support Services GmbH (Type Certificate Previously Held by AvCraft...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-01

... identified as stress corrosion. This condition, if not corrected, could lead to in-flight failure of the tab... was found on a trim tab fitting assembly. The cause of the cracking was identified as stress corrosion... is more resistant to stress corrosion. The improved material rudder spring tab fittings were...

Inspection of the Armed Forces Retirement Home

DTIC Science & Technology

2010-02-25

22 Tab D – Information Technology ............................................................................................. 25 Tab E...Forces Retirement Home February 25, 2010 Report No. IE-2010-002 Tab D – Information Technology Overall Assessment We used the National Institute of Science...and Technology (NIST) SP 800-53, Revision 2, “Recommended Security Controls for Federal Information Systems,” dated December 2007 as the basis for

76 FR 13069 - Airworthiness Directives; BAE Systems (Operations) Limited Model ATP Airplanes; BAE Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

..., an operator found an aileron trim tab hinge pin that had migrated sufficiently to cause a rubbing.... Recently, during a walk round check, an operator found an aileron trim tab hinge pin that had migrated... walk round check, an operator found an aileron trim tab hinge pin that had migrated sufficiently to...

Lift enhancing tabs for airfoils

NASA Technical Reports Server (NTRS)

Ross, James C. (Inventor)

1994-01-01

A tab deployable from the trailing edge of a main airfoil element forces flow onto a following airfoil element, such as a flap, to keep the flow attached and thus enhance lift. For aircraft wings with high lift systems that include leading edge slats, the slats may also be provided with tabs to turn the flow onto the following main element.

76 FR 34011 - Airworthiness Directives; Viking Air Limited (Type Certificate No. A-815 Formerly Held by...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

... listed above. The existing AD currently requires repetitively inspecting the elevator control tabs for... section. We are proposing this AD to add new repetitive inspections of the elevator control tabs. If these inspections are not done, excessive free-play in the elevator control tabs could develop. This condition could...

75 FR 16648 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

.... Subsequent investigation revealed extensive damage to the elevator tab control system. Severe vibration in... and right elevator control tab mechanisms for gaps between the swage ring and the aft attach lug, and... replacing any discrepant elevator tab control mechanism, including performing the detailed inspection on the...

VA and DoD Operating as One

DTIC Science & Technology

2011-01-25

Dextromethorphan Hydrobromide U UD ŕ RFO DoD Menthol + Cetylpyridinium Chloride, lozenge, I USE AS DIRECTED FOR COUGH I DoD ACETAMINOPHEN. 325 MG. TABLET...ORAL TAKE 1·2 TABS EVERY 4-6HOUR DoD BISMUTH SU8SAUCYLATE. 262 MG. TAB C~ CHEW 2 TABS EVERY 1/2 HOUR DoD Menthol + Cetylpyridinium Chloride

Multidisciplinary design integration system for a supersonic transport aircraft

NASA Technical Reports Server (NTRS)

Dovi, A. R.; Wrenn, G. A.; Barthelemy, J.-F. M.; Coen, P. G.; Hall, L. E.

1992-01-01

An aircraft preliminary design system which provides the multidisciplinary communications and couplings between several engineering disciplines is described. A primary benefit of this system is to demonstrate advanced technology multidisciplinary design integration methodologies. The current version includes the disciplines of aerodynamics and structures. Contributing engineering disciplines are coupled using the Global Sensitivity Equation approach to influence the global design optimization problem. A high speed civil transport configuration is used for configuration trade studies. Forty four independent design variables are used to control the cross-sectional areas of wing rib and spar caps and the thicknesses of wingskincover panels. A total of 300 stress, strain, buckling and displacement behavioral constraints and minimum gages on the design variables were used to optimize the idealized wing structure. The goal of the designs to resize the wing cover panels and internal structure for minimum mass.

Self adaptive solution strategies: Locally bound constrained Newton Raphson solution algorithms

NASA Technical Reports Server (NTRS)

Padovan, Joe

1991-01-01

A summary is given of strategies which enable the automatic adjustment of the constraint surfaces recently used to extend the range and numerical stability/efficiency of nonlinear finite element equation solvers. In addition to handling kinematic and material induced nonlinearity, both pre-and postbuckling behavior can be treated. The scheme employs localized bounds on various hierarchical partitions of the field variables. These are used to resize, shape, and orient the global constraint surface, thereby enabling essentially automatic load/deflection incrementation. Due to the generality of the approach taken, it can be implemented in conjunction with the constraints of an arbitrary functional type. To benchmark the method, several numerical experiments are presented. These include problems involving kinematic and material nonlinearity, as well as pre- and postbuckling characteristics. Also included is a list of papers published in the course of the work.

Modular, security enclosure and method of assembly

DOEpatents

Linker, Kevin L.; Moyer, John W.

1995-01-01

A transportable, reusable rapidly assembled and disassembled, resizable modular, security enclosure utilizes a stepped panel construction. Each panel has an inner portion and an outer portion which form joints. A plurality of channels can be affixed to selected joints of the panels. Panels can be affixed to a base member and then affixed to one another by the use of elongated pins extending through the channel joints. Alternatively, the base member can be omitted and the panels themselves can be used as the floor of the enclosure. The pins will extend generally parallel to the joint in which they are located. These elongated pins are readily inserted into and removable from the channels in a predetermined sequence to allow assembly and disassembly of the enclosure. A door constructed from panels is used to close the opening to the enclosure.

Nursing education: training evaluation by graduates, employers and teachers.

PubMed

Meira, Maria Dyrce Dias; Kurcgant, Paulina

2016-01-01

to support the assessment and the necessary changes in the curriculum of an undergraduate degree in Nursing. it is a descriptive study developed in two stages as an action research. In the first stage, the speeches of 19 graduates and 15 employers were interviewed and analyzed; in the second stage, five teachers participated in the focus group. For processing the data, the content analysis was adopted. based on the assessment of the actors, an action plan was created with suggestions regarding the curriculum flexibility, content resizing, continuing education, practice enhancement, active methodologies and autonomy of the student. the participation of actors participants of the training process and performance of professional nurses in the evaluation of a curriculum pointed aspects to realignment and provided concrete benefits to improving the quality of undergraduate course curriculum, scenario of this study.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Broad Funding Opportunity Announcement Project: Led by MIT professor Donald Sadoway, the Electroville project team is creating a community-scale electricity storage device using new materials and a battery design inspired by the aluminum production process known as smelting. A conventional battery includes a liquid electrolyte and a solid separator between its 2 solid electrodes. MIT’s battery contains liquid metal electrodes and a molten salt electrolyte. Because metals and salt don’t mix, these 3 liquids of different densities naturally separate into layers, eliminating the need for a solid separator. This efficient design significantly reduces packaging materials, which reduces cost and allowsmore » more space for storing energy than conventional batteries offer. MIT’s battery also uses cheap, earth-abundant, domestically available materials and is more scalable. By using all liquids, the design can also easily be resized according to the changing needs of local communities.« less

Mixing Enhancement by Tabs in Round Supersonic Jets

NASA Technical Reports Server (NTRS)

Seiner, John M.; Grosch, C. E.

1998-01-01

The objective of this study was to analyze jet plume mass flow entrainment rates associated with the introduction of counter-rotating streamwise vorticity by prism shaped devices (tabs) located at the lip of the nozzle. We have examined the resulting mixing process through coordinated experimental tests and numerical simulations of the supersonic flow from a model axisymmetric nozzle. In the numerical simulations, the total induced vorticity was held constant while varying the distribution of counter-rotating vorticity around the nozzle lip training edge. In the experiment, the number of tabs applied was varied while holding the total projected area constant. Evaluations were also conducted on initial vortex strength. The results of this work show that the initial growth rate of the jet shear layer is increasingly enhanced as more tabs are added, but that the lowest tab count results in the largest entrained mass flow. The numerical simulations confirm these results.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cavieres, Andres; Al-Haddad, Tristan; Goodman, Joseph

A photovoltaic panel mounting clip comprising a base, central indexing tabs, flanges, lateral indexing tabs, and vertical indexing tabs. The mounting clip removably attaches one or more panels to a beam or the like structure, both mechanically and electrically. It provides secure locking of the panels in all directions, while providing guidance in all directions for accurate installation of the panels to the beam or the like structure.

Adhesive-Bonded Tab Attaches Thermocouples to Titanium

NASA Technical Reports Server (NTRS)

Cook, C. F.

1982-01-01

Mechanical strength of titanium-alloy structures that support thermocouples is preserved by first spotwelding thermocouples to titanium tabs and then attaching tabs to titanium with a thermosetting adhesive. In contrast to spot welding, a technique previously used for thermocouples, fatigue strength of the titanium is unaffected by adhesive bonding. Technique is also gentler than soldering or attaching thermocouples with a tap screw.

78 FR 23112 - Airworthiness Directives; Grob-Werke Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-18

... aviation product. The MCAI describes the unsafe condition as cracks in the elevator trim tab arms on... MCAI states: On several Grob G 115 aeroplanes, elevator trim tab arms Part Number (P/N) 115E-3758 have been found cracked, from a rear mounting hole (either L/H or R/H) to the rear edge of the trim tab arm...

25 CFR 542.8 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false What are the minimum internal control standards for pull tabs? 542.8 Section 542.8 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.8 What are the minimum internal control standards for pull tabs? (a) Computer applications. For...

25 CFR 542.8 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false What are the minimum internal control standards for pull tabs? 542.8 Section 542.8 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.8 What are the minimum internal control standards for pull tabs? (a) Computer applications. For...

25 CFR 542.8 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 2 2012-04-01 2012-04-01 false What are the minimum internal control standards for pull tabs? 542.8 Section 542.8 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.8 What are the minimum internal control standards for pull tabs? (a) Computer applications. For...

TABS Manual for the Temperament and Atypical Behavior Scale: Early Childhood Indicators of Developmental Dysfunction.

ERIC Educational Resources Information Center

Neisworth, John T.; Bagnato, Stephen J.; Salvia, John; Hunt, Frances M.

This manual describes the rationale, use, and validity of the Temperament and Atypical Behavior Scale (TABS), a norm-referenced measure of dysfunctional behavior appropriately used with infants and young children between the ages of 11 and 71 months. TABS is intended to identify children who are developing atypically or are at risk for atypical…

Apparatus for preparing cornea material for tabbed (sutureless) transplantation

DOEpatents

Collins, Joseph Patrick

1997-01-01

A tool and a method for preparing a donor material used in sutureless corneal transplants uses a first cutting portion to prepare a donor blank having tabbed portions extending outwardly radially. A second cutting portion is used to cut the central portion of the blank. The tool is used as a guide member for the second cutting portion. In one embodiment the tool has slits laterally defined therethrough which allow the tabbed portions of the donor material to be thinned to a desired thickness using a scalpel. In an another embodiment the second cutting portion is a round trephine which is used to simultaneously trim each of the tabbed portions.

Lattice-structures and constructs with designed thermal expansion coefficients

DOEpatents

Spadaccini, Christopher; Hopkins, Jonathan

2014-10-28

A thermal expansion-managed lattice structure having a plurality of unit cells each having flexure bearing-mounted tabs supported on a base and actuated by thermal expansion of an actuator having a thermal expansion coefficient greater than the base and arranged so that the tab is inwardly displaced into a base cavity. The flexure bearing-mounted tabs are connected to other flexure-bearing-mounted tabs of adjacent unit cells so that the adjacent unit cells are spaced from each other to accommodate thermal expansion of individual unit cells while maintaining a desired bulk thermal expansion coefficient of the lattice structure as a whole.

A recognizable systemic connective tissue disorder with polyvalvular heart dystrophy and dysmorphism associated with TAB2 mutations.

PubMed

Ritelli, M; Morlino, S; Giacopuzzi, E; Bernardini, L; Torres, B; Santoro, G; Ravasio, V; Chiarelli, N; D'Angelantonio, D; Novelli, A; Grammatico, P; Colombi, M; Castori, M

2018-01-01

Deletions encompassing TAK1-binding protein 2 (TAB2) associated with isolated and syndromic congenital heart defects. Rare missense variants are found in patients with a similar phenotype as well as in a single individual with frontometaphyseal dysplasia. We describe a family and an additional sporadic patient with polyvalvular heart disease, generalized joint hypermobility and related musculoskeletal complications, soft, velvety and hyperextensible skin, short limbs, hearing impairment, and facial dysmorphism. In the first family, whole-exome sequencing (WES) disclosed the novel TAB2 c.1398dup (p.Thr467Tyrfs*6) variant that eliminates the C-terminal zinc finger domain essential for activation of TAK1 (TGFβ-activated kinase 1)-dependent signaling pathways. The sporadic case carryed a ~2 Mb de novo deletion including 28 genes also comprising TAB2. This study reveal an association between TAB2 mutations and a phenotype resembling Ehlers-Danlos syndrome with severe polyvalvular heart disease and subtle facial dysmorphism. Our findings support the existence of a wider spectrum of clinical phenotypes associated with TAB2 perturbations and emphasize the role of TAK1 signaling network in human development. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Exploring the use of tablet technology as a teaching tool at Kolej Matrikulasi Perak

NASA Astrophysics Data System (ADS)

Mohamad Amirnudin, Mohamad Tahar; Sulaiman, Hajar

2013-04-01

The use of technology in teaching and learning (T&L) of mathematics is gaining popularity these days. There are various technologies that are designed to facilitate the process of learning, such as graphic calculators, three-dimensional projectors and multimedia softwares. Tablet is a portable technology used as a tool for communication and information search. In addition, it can also be used as a teaching aid. Galaxy Tab (tab) is a tablet produced by the giant company SAMSUNG which uses Android operating system. For this study, the researcher had to download and install the two softwares, SynSpace and Google + into the tab. The purpose of this study was to explore the use of tabs in the T&L of mathematics and get the students' perceptions. This study is divided into five phases. In Phase One, the researcher prepared the lesson plan. In the Second Phase, a workshop was conducted to introduce the students to the basic use of tab which contained two modules: Module 1 was on Syncspace Applications and Module 2 was on Google+. Third phase involves teaching and learning mathematics using tab. In Phase Four, questionnaires were distributed and then collected to obtain the data for analysis. In Phase Five, the collected data was analyzed using simple statistics involving frequency tables and bar charts. The findings showed that the use of tab in teaching and learning mathematics was accepted very by the students at Kolej Matrikulasi Perak.

Spreading Characteristics and Thrust of Jets from Asymmetric Nozzles

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

1995-01-01

The spreading characteristics of jets from several asymmetric nozzles are studied in comparison to those of an axisymmetric jet, over the Mach number (M(sub J)) range of 0.3 to 1.96. The effect of tabs in two cases, the axisymmetric nozzle fitted with four tabs and a rectangular nozzle fitted with two large tabs, is also included in the comparison. Compared to the axisymmetric jet, the asymmetric jets spread only slightly faster at subsonic conditions, while at supersonic conditions, when screech occurs, they spread much faster. Screech profoundly increases the spreading of all jets. The effect varies in the different stages of screech, and the corresponding unsteady flowfield characteristics are documented via phase-averaged measurement of the fluctuating total pressure. An organization and intensification of the azimuthal vortical structures under the screeching condition is believed to be responsible for the increased spreading. Curiously, the jet from a 'lobed mixer' nozzle spreads much less at supersonic conditions compared to all other cases. This is due to the absence of screech with this nozzle. Jet spreading for the two tab configurations, on the other hand, is significantly more than any of the no-tab cases. This is true in the subsonic regime, as well as in the supersonic regime in spite of the fact that screech is essentially eliminated by the tabs. The dynamics of the streamwise vortex pairs produced by the tabs cause the most efficient jet spreading thus far observed in the study.

25 CFR 543.9 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false What are the minimum internal control standards for pull tabs? 543.9 Section 543.9 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS FOR CLASS II GAMING § 543.9 What are the minimum internal control standards for pull tabs? (a)...

25 CFR 543.9 - What are the minimum internal control standards for pull tabs?

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false What are the minimum internal control standards for pull tabs? 543.9 Section 543.9 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS FOR CLASS II GAMING § 543.9 What are the minimum internal control standards for pull tabs? (a)...

TabHLH1, a bHLH-type transcription factor gene in wheat, improves plant tolerance to Pi and N deprivation via regulation of nutrient transporter gene transcription and ROS homeostasis.

PubMed

Yang, Tongren; Hao, Lin; Yao, Sufei; Zhao, Yuanyuan; Lu, Wenjing; Xiao, Kai

2016-07-01

Basic helix-loop-helix (bHLH) transcription factors (TFs) comprise a large TF family and act as crucial regulators in various biological processes in plants. Here, we report the functional characterization of TabHLH1, a bHLH TF member in wheat (Triticum aestivum). TabHLH1 shares conserved bHLH domain and targets to nucleus with transactivation activity. Upon Pi and N deprivation, the expression of TabHLH1 was up-regulated in roots and leaves, showing a pattern to be gradually increased within 23-h treatment regimes. The lines with overexpression of TabHLH1 exhibited drastically improved tolerance to Pi and N deprivation, showing larger plant phenotype, more biomass, higher concentration and more accumulation of P and N than wild type (WT) upon the Pi- and N-starvation stresses. NtPT1 and NtNRT2.2, the genes encoding phosphate transporter (PT) and nitrate transporter (NRT) in tobacco, respectively, showed up-regulated expression in TabHLH1-overexpressing plants; knockdown expression of them led to deteriorated growth feature, lowered biomass, and decreased nutrient accumulation of plants under Pi- and N-deficient conditions. Compared with WT, the TabHLH1-overexpressing plants also showed lowered reactive oxygen species (ROS) accumulation and improved antioxidant enzyme (AE) activities, such as those of superoxide dismutase (SOD), catalase (CAT), and peroxidase (POD). NtSOD1, NtCAT1, and NtPOD1;6 that encode SOD, CAT, and POD, respectively, were up-regulated in TabHLH1-overexpressing plants. Further knockdown of these AE gene expression caused reduced antioxidant enzymatic activities, indicative of their crucial roles in mediating cellular ROS homeostasis in Pi- and N-starvation conditions. Together, TabHLH1 plays an important role in mediating adaptation to the Pi- and N-starvation stresses through transcriptional regulation of a set of genes encoding PT, NRT and AEs that mediate the taken up of Pi and N and the cellular homeostasis of ROS initiated by the nutrient stresses. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Apparatus for preparing cornea material for tabbed (sutureless) transplantation

DOEpatents

Collins, J.P.

1997-07-22

A tool and a method for preparing a donor material used in sutureless corneal transplants uses a first cutting portion to prepare a donor blank having tabbed portions extending outwardly radially. A second cutting portion is used to cut the central portion of the blank. The tool is used as a guide member for the second cutting portion. In one embodiment the tool has slits laterally defined therethrough which allow the tabbed portions of the donor material to be thinned to a desired thickness using a scalpel. In an another embodiment the second cutting portion is a round trephine which is used to simultaneously trim each of the tabbed portions. 26 figs.

Explorative visual analytics on interval-based genomic data and their metadata.

PubMed

Jalili, Vahid; Matteucci, Matteo; Masseroli, Marco; Ceri, Stefano

2017-12-04

With the wide-spreading of public repositories of NGS processed data, the availability of user-friendly and effective tools for data exploration, analysis and visualization is becoming very relevant. These tools enable interactive analytics, an exploratory approach for the seamless "sense-making" of data through on-the-fly integration of analysis and visualization phases, suggested not only for evaluating processing results, but also for designing and adapting NGS data analysis pipelines. This paper presents abstractions for supporting the early analysis of NGS processed data and their implementation in an associated tool, named GenoMetric Space Explorer (GeMSE). This tool serves the needs of the GenoMetric Query Language, an innovative cloud-based system for computing complex queries over heterogeneous processed data. It can also be used starting from any text files in standard BED, BroadPeak, NarrowPeak, GTF, or general tab-delimited format, containing numerical features of genomic regions; metadata can be provided as text files in tab-delimited attribute-value format. GeMSE allows interactive analytics, consisting of on-the-fly cycling among steps of data exploration, analysis and visualization that help biologists and bioinformaticians in making sense of heterogeneous genomic datasets. By means of an explorative interaction support, users can trace past activities and quickly recover their results, seamlessly going backward and forward in the analysis steps and comparative visualizations of heatmaps. GeMSE effective application and practical usefulness is demonstrated through significant use cases of biological interest. GeMSE is available at http://www.bioinformatics.deib.polimi.it/GeMSE/ , and its source code is available at https://github.com/Genometric/GeMSE under GPLv3 open-source license.

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 1: Results and discussion

NASA Technical Reports Server (NTRS)

Brown, W. H.; Ahuja, K. K.

1989-01-01

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. The conclusions derived were: (1) intrusive probes can produce significant errors in the measurements of the velocity of jets if they are large in diameter and penetrate beyond the jet center; (2) rectangular jets without tabs, compared to circular jets of the same exit area, provide faster jet mixing; and (3) further mixing enhancement is possible by using mechanical tabs.

Evaluation of Dental Shade Guide Variability Using Cross-Polarized Photography.

PubMed

Gurrea, Jon; Gurrea, Marta; Bruguera, August; Sampaio, Camila S; Janal, Malvin; Bonfante, Estevam; Coelho, Paulo G; Hirata, Ronaldo

2016-01-01

This study evaluated color variability in the A hue between the VITA Classical (VITA Zahnfabrik) shade guide and four other VITA-coded ceramic shade guides using a Canon EOS 60D camera and software (Photoshop CC, Adobe). A total of 125 photographs were taken, 5 per shade tab for each of 5 shades (A1 to A4) from the following shade guides: VITA Classical (control), IPS e.max Ceram (Ivoclar Vivadent), IPS d.SIGN (Ivoclar Vivadent), Initial ZI (GC), and Creation CC (Creation Willi Geller). Photos were processed with Adobe Photoshop CC to allow standardized evaluation of hue, chroma, and value between shade tabs. None of the VITA-coded shade tabs fully matched the VITA Classical shade tab for hue, chroma, or value. The VITA-coded shade guides evaluated herein showed an overall unmatched shade in all tabs when compared with the control, suggesting that shade selection should be made using the guide produced by the manufacturer of the ceramic intended for the final restoration.

Evaluation of a standard shade guide for color change after disinfection.

PubMed

Pohjola, Randall M; Hackman, Steven T; Browning, William D

2007-09-01

To determine if surface disinfectants cause a change in the shade perception of a standard Classic Vitapan shade guide. Consistency in shade selection for dental restorations involves many factors, and one of the most important is the shade tabs used in the selection process. Ten shade tabs each of shades B2, D2, C1, and A3.5 were selected from the Classic Vitapan shade guide (Vident). All tabs were measured with the EasyShade shade device (Vident) at baseline. Three tabs of each shade were set aside as controls. The other 7 tabs of each shade were treated with the surface disinfectant Cavicide (Metrex Research) for 480 cycles to simulate a year's usage. After each 480 cycles, all the tabs were again measured with the EasyShade. This process was repeated to simulate 2 and 3 years of use. The data were analyzed to calculate the delta E 2000 for any change. A statistically significant increase was observed in the value (L*) and chroma (C*) after 2 and 3 years of simulated treatments. These changes were not perceptible to the clinician. The authors suggest that 1 standard shade guide be set aside to compare against those in clinical use to determine when they should be replaced.

Haploinsufficiency of TAB2 Causes Congenital Heart Defects in Humans

PubMed Central

Thienpont, Bernard; Zhang, Litu; Postma, Alex V.; Breckpot, Jeroen; Tranchevent, Léon-Charles; Van Loo, Peter; Møllgård, Kjeld; Tommerup, Niels; Bache, Iben; Tümer, Zeynep; van Engelen, Klaartje; Menten, Björn; Mortier, Geert; Waggoner, Darrel; Gewillig, Marc; Moreau, Yves; Devriendt, Koen; Larsen, Lars Allan

2010-01-01

Congenital heart defects (CHDs) are the most common major developmental anomalies and the most frequent cause for perinatal mortality, but their etiology remains often obscure. We identified a locus for CHDs on 6q24-q25. Genotype-phenotype correlations in 12 patients carrying a chromosomal deletion on 6q delineated a critical 850 kb region on 6q25.1 harboring five genes. Bioinformatics prioritization of candidate genes in this locus for a role in CHDs identified the TGF-β-activated kinase 1/MAP3K7 binding protein 2 gene (TAB2) as the top-ranking candidate gene. A role for this candidate gene in cardiac development was further supported by its conserved expression in the developing human and zebrafish heart. Moreover, a critical, dosage-sensitive role during development was demonstrated by the cardiac defects observed upon titrated knockdown of tab2 expression in zebrafish embryos. To definitively confirm the role of this candidate gene in CHDs, we performed mutation analysis of TAB2 in 402 patients with a CHD, which revealed two evolutionarily conserved missense mutations. Finally, a balanced translocation was identified, cosegregating with familial CHD. Mapping of the breakpoints demonstrated that this translocation disrupts TAB2. Taken together, these data clearly demonstrate a role for TAB2 in human cardiac development. PMID:20493459

Vortex dynamics in the near-wake of tabs with various geometries using 2D and 3D PIV

NASA Astrophysics Data System (ADS)

Pagan-Vazquez, Axy; Khovalyg, Dolaana; Marsh, Charles; Hamed, Ali M.; Chamorro, Leonardo P.

2016-11-01

The vortex dynamics and turbulence statistics in the near-wake of rectangular, trapezoidal, triangular, and ellipsoidal tabs were studied in a refractive-index-matching channel at Re = 2000 and 13000, based on the tab height. The tabs share the same bulk dimensions including a 17 mm height, a 28 mm base width, and a 24.5o angle. 3D PIV was used to study the mean flow and dominant large-scale vortices, while high-spatial resolution planar PIV was used to quantify high-order statistics. The results show the coexistence of counter-rotating vortex pair (CVP) and hairpin structures. These vortices exhibit distinctive topology and strength across Re and tab geometry. The CVP is a steady structure that grows in strength over a significantly longer distance at the low Re due to the lower turbulence levels and the delayed shedding of the hairpin vortices. These features at the low Re are associated with the presence of K-H instability that develops over three tab heights. The interaction between the hairpins and CVP is measured in 3D for the first time and shows complex coexistence. Although the CVP suffers deformation and splitting at times, it maintains its presence and leads to significant spanwise and wall-normal flows.

TAB interconnects for space concentrator solar cell arrays

NASA Technical Reports Server (NTRS)

Avery, J.; Bauman, J. S.; Gallagher, P.; Yerkes, J. W.

1993-01-01

The Boeing Company has evaluated the use of Tape Automated Bonding (TAB) and Surface Mount Technology (SMT) for a highly reliable, low cost interconnect for concentrator solar cell arrays. TAB and SMT are currently used in the electronics industry for chip interconnects and printed circuit board assembly. TAB tape consists of sixty-four 3-mil/1-oz tin-plated copper leads on 8-mil centers. The leads are thermocompression gang bonded to GaAs concentrator solar cell with silver contacts. This bond, known as an Inner Lead Bond (ILB), allows for pretesting and sorting capability via nondestruct wire bond pull and flash testing. Destructive wire pull tests resulted in preferred mid-span failures. Improvements in fill factor were attributed to decreased contact resistance on TAB bonded cells. Preliminary thermal cycling and aging tests were shown excellent bond strength and metallurgical results. Auger scans of bond sites reveals an Ag-Cu-Tin composition. Improper bonds are identified through flash testing as a performance degradation. On going testing of cells are underway at Lewis Research Center. SMT techniques are utilized to excise and form TAB leads post ILB. The formed leads' shape isolates thermal mismatches between the cells and the flex circuit they are mounted on. TABed cells are picked and placed with a gantry x-y-z positioning system with pattern recognition. Adhesives are selected to avoid thermal expansion mismatch and promote thermal transfer to the flex circuit. TAB outer lead bonds are parallel gap welded (PGW) to the flex circuit to finish the concentrator solar cell subassembly.

Influence of illuminants on the color distribution of shade guides.

PubMed

Park, Ji-Hoon; Lee, Yong-Keun; Lim, Bum-Soon

2006-12-01

Although a shade tab in a shade guide is matched to a natural tooth in the order of value, hue, and chroma, there are limited data on the color distribution of currently available shade guides sorted by these 3 parameters. Furthermore, spectrophotometric color measurements of shade tabs differ depending on the standard illuminant employed. The purpose of this study was to determine the color distributions of 2 shade guides in value (CIE L( *)), chroma (C( *)(ab)) and hue angle (h(o)) scale relative to the standard illuminants D(65), A, and F2. Color of shade tabs (n=36) from 2 shade guides (Vita Lumin and Chromascop) were measured, and the distributions for CIE L( *), C( *)(ab) and h(o) values were compared. Color differences of shade tabs depending on the illuminant were calculated. The distributions of the ratios of CIE L( *) and C( *)(ab) values of each shade tab compared with the lowest value tab or the lowest chroma tab were determined. The data for the value, chroma, and hue angle within each shade guide were analyzed with a 2-way ANOVA with the factors of shade designation and type of illuminant (alpha=.05). Color difference caused by change of illuminant was analyzed with a 2-way ANOVA with the factors of shade designation and pair of illuminants compared (alpha=.05). The Scheffe multiple comparison test was performed as a post hoc test. CIE L( *), C( *)(ab) and h(o) values were influenced by shade designation and type of illuminant in both shade guides. Color difference caused by change of the illuminant was influenced by the shade designation and pair of illuminants compared. The order of mean color differences of 16 Vita Lumin shade tabs by pairs of illuminants compared was as follows: DeltaE( *)(ab) (D(65)/F2) = 1.63 3.7). Color distribution of 2 shade guides by the value and chroma was not logical.

Means of determining extrusion temperatures

DOEpatents

McDonald, Robert E.; Canonico, Domenic A.

1977-01-01

In an extrusion process comprising the steps of fabricating a metal billet, heating said billet for a predetermined time and at a selected temperature to increase its plasticity and then forcing said heated billet through a small orifice to produce a desired extruded object, the improvement comprising the steps of randomly inserting a plurality of small metallic thermal tabs at different cross sectional depths in said billet as a part of said fabricating step, and examining said extruded object at each thermal tab location for determining the crystal structure at each extruded thermal tab thus revealing the maximum temperature reached during extrusion in each respective tab location section of the extruded object, whereby the thermal profile of said extruded object during extrusion may be determined.

TabPath: interactive tables for metabolic pathway analysis.

PubMed

Moraes, Lauro Ângelo Gonçalves de; Felestrino, Érica Barbosa; Assis, Renata de Almeida Barbosa; Matos, Diogo; Lima, Joubert de Castro; Lima, Leandro de Araújo; Almeida, Nalvo Franco; Setubal, João Carlos; Garcia, Camila Carrião Machado; Moreira, Leandro Marcio

2018-03-15

Information about metabolic pathways in a comparative context is one of the most powerful tool to help the understanding of genome-based differences in phenotypes among organisms. Although several platforms exist that provide a wealth of information on metabolic pathways of diverse organisms, the comparison among organisms using metabolic pathways is still a difficult task. We present TabPath (Tables for Metabolic Pathway), a web-based tool to facilitate comparison of metabolic pathways in genomes based on KEGG. From a selection of pathways and genomes of interest on the menu, TabPath generates user-friendly tables that facilitate analysis of variations in metabolism among the selected organisms. TabPath is available at http://200.239.132.160:8686. lmmorei@gmail.com.

A comparative study of basal metabolism and thermoregulation in a folivorous (Colobus guereza) and an omnivorous (Cercopithecus mitis) primate species.

PubMed

Müller, E F; Kamau, J M; Maloiy, G M

1983-01-01

1. Abdominal temperatures (Tab) and oxygen consumption (VO2) were measured in two males each of colobus and Sykes monkeys. 2. Tab in both species had the same range (36 38.5 C), but there were marked differences in the daily rhythms. 3. Low ambient temperatures (Ta) had little effect on Tab; at Ta = 33.5 35.5 C. however, Tab rose quickly to above 40 C. 4. The thermoneutral zone (TNZ) extended from about 5 to 28 C in both species. 5. In the colobus monkeys the basal metabolic rate (BMR) was considerably lower than in the Sykes monkeys: 85% vs 113% of the value predicted from body mass.

Surface, interphase and tensile properties of unsized, sized and heat treated basalt fibres

NASA Astrophysics Data System (ADS)

Förster, T.; Sommer, G. S.; Mäder, E.; Scheffler, C.

2016-07-01

Recycling of fibre reinforced polymers is in the focus of several investigations. Chemical and thermal treatments of composites are the common ways to separate the reinforcing fibres from the polymer matrices. However, most sizings on glass and basalt fibre are not designed to resist high temperatures. Hence, a heat treatment might also lead to a sizing removal, a decrease of mechanical performance and deterioration in fibre-matrix adhesion. Different basalt fibres were investigated using surface analysis methods as well as single fibre tensile tests and single fibre pull-out tests in order to reveal the possible causes of these issues. Heat treatment in air reduced the fibre tensile strength in the same level like heat treatment in nitrogen atmosphere, but it influenced the wetting capability. Re-sizing by a coupling agent slightly increased the adhesion strength and reflected a decreased post-debonding friction.

Visualization of molecular structures using HoloLens-based augmented reality

PubMed Central

Hoffman, MA; Provance, JB

2017-01-01

Biological molecules and biologically active small molecules are complex three dimensional structures. Current flat screen monitors are limited in their ability to convey the full three dimensional characteristics of these molecules. Augmented reality devices, including the Microsoft HoloLens, offer an immersive platform to change how we interact with molecular visualizations. We describe a process to incorporate the three dimensional structures of small molecules and complex proteins into the Microsoft HoloLens using aspirin and the human leukocyte antigen (HLA) as examples. Small molecular structures can be introduced into the HoloStudio application, which provides native support for rotating, resizing and performing other interactions with these molecules. Larger molecules can be imported through the Unity gaming development platform and then Microsoft Visual Developer. The processes described here can be modified to import a wide variety of molecular structures into augmented reality systems and improve our comprehension of complex structural features. PMID:28815109

A VLSI implementation of DCT using pass transistor technology

NASA Technical Reports Server (NTRS)

Kamath, S.; Lynn, Douglas; Whitaker, Sterling

1992-01-01

A VLSI design for performing the Discrete Cosine Transform (DCT) operation on image blocks of size 16 x 16 in a real time fashion operating at 34 MHz (worst case) is presented. The process used was Hewlett-Packard's CMOS26--A 3 metal CMOS process with a minimum feature size of 0.75 micron. The design is based on Multiply-Accumulate (MAC) cells which make use of a modified Booth recoding algorithm for performing multiplication. The design of these cells is straight forward, and the layouts are regular with no complex routing. Two versions of these MAC cells were designed and their layouts completed. Both versions were simulated using SPICE to estimate their performance. One version is slightly faster at the cost of larger silicon area and higher power consumption. An improvement in speed of almost 20 percent is achieved after several iterations of simulation and re-sizing.

Accuracy concerns in digital speckle photography combined with Fresnel digital holographic interferometry

NASA Astrophysics Data System (ADS)

Zhao, Yuchen; Zemmamouche, Redouane; Vandenrijt, Jean-François; Georges, Marc P.

2018-05-01

A combination of digital holographic interferometry (DHI) and digital speckle photography (DSP) allows in-plane and out-of-plane displacement measurement between two states of an object. The former can be determined by correlating the two speckle patterns whereas the latter is given by the phase difference obtained from DHI. We show that the amplitude of numerically reconstructed object wavefront obtained from Fresnel in-line digital holography (DH), in combination with phase shifting techniques, can be used as speckle patterns in DSP. The accuracy of in-plane measurement is improved after correcting the phase errors induced by reference wave during reconstruction process. Furthermore, unlike conventional imaging system, Fresnel DH offers the possibility to resize the pixel size of speckle patterns situated on the reconstruction plane under the same optical configuration simply by zero-padding the hologram. The flexibility of speckle size adjustment in Fresnel DH ensures the accuracy of estimation result using DSP.

Advanced aerosense display interfaces

NASA Astrophysics Data System (ADS)

Hopper, Darrel G.; Meyer, Frederick M.

1998-09-01

High-resolution display technologies are being developed to meet the ever-increasing demand for realistic detail. The requirement for evermore visual information exceeds the capacity of fielded aerospace display interfaces. In this paper we begin an exploration of display interfaces and evolving aerospace requirements. Current and evolving standards for avionics, commercial, and flat panel displays are summarized and compared to near term goals for military and aerospace applications. Aerospace and military applications prior to 2005 up to UXGA and digital HDTV resolution can be met by using commercial interface standard developments. Advanced aerospace requirements require yet higher resolutions (2560 X 2048 color pixels, 5120 X 4096 color pixels at 85 Hz, etc.) and necessitate the initiation of discussion herein of an 'ultra digital interface standard (UDIS)' which includes 'smart interface' features such as large memory and blazingly fast resizing microcomputer. Interface capacity, IT, increased about 105 from 1973 to 1998; 102 more is needed for UDIS.

NASA-UVa Light Aerospace Alloy and Structures Technology Program: Aluminum-Based Materials for High Speed Aircraft

NASA Technical Reports Server (NTRS)

Starke, E. A., Jr. (Editor)

1996-01-01

This report is concerned with 'Aluminum-Based Materials for High Speed Aircraft' which was initiated to identify the technology needs associated with advanced, low-cost aluminum base materials for use as primary structural materials. Using a reference baseline aircraft, these materials concept will be further developed and evaluated both technically and economically to determine the most attractive combinations of designs, materials, and manufacturing techniques for major structural sections of an HSCT. Once this has been accomplished, the baseline aircraft will be resized, if applicable, and performance objectives and economic evaluations made to determine aircraft operating costs. The two primary objectives of this study are: (1) to identify the most promising aluminum-based materials with respect to major structural use on the HSCT and to further develop those materials, and (2) to assess these materials through detailed trade and evaluation studies with respect to their structural efficiency on the HSCT.

Integrated digital/electric aircraft concepts study

NASA Technical Reports Server (NTRS)

Cronin, M. J.; Hays, A. P.; Green, F. B.; Radovcich, N. A.; Helsley, C. W.; Rutchik, W. L.

1985-01-01

The integrated digital/electrical aircraft (IDEA) is an aircraft concept which employs all electric secondary power systems and advanced digital flight control systems. After trade analysis, preferred systems were applied to the baseline configuration. An additional configuration, the alternate IDEA, was also considered. For this concept the design ground rules were relaxed in order to quantify additional synergistic benefits. It was proposed that an IDEA configuration and technical risks associated with the IDEA systems concepts be defined and the research and development required activities to reduce these risks be identified. The selected subsystems include: power generation, power distribution, actuators, environmental control system and flight controls systems. When the aircraft was resized, block fuel was predicted to decrease by 11.3 percent, with 7.9 percent decrease in direct operating cost. The alternate IDEA shows a further 3.4 percent reduction in block fuel and 3.1 percent reduction in direct operating cost.

First uses of HAART 300 rings for aortic valve repair in Poland - 4 case studies.

PubMed

Juściński, Jacek H; Koprowski, Andrzej; Kołaczkowska, Magdalena; Kowalik, Maciej M; Rogowski, Jan A; Rankin, James S

2018-03-01

Aortic valve reconstructions using geometric annuloplasty rings HAART 300/200 open new era in aortic valve surgery. The HAART technology resizes, reshapes, stabilizes and simplifies aortic valve repair. The HAART aortic repair rings are designed to be implanted directly into aortic annulus (under aortic valve leaflets). We present first in Poland 4 cases of aortic valve reconstructions using geometric annuloplasty rings HAART 300. Two patients had type IA aortic insufficiency (due to El-Khoury classification) - they were treated by HAART 300 ring insertion and ascending aorta prosthesis implantation. Third patient, Marfan with type IB aortic insufficiency was repaired by HAART 300 ring implantation followed by remodeling (Yacoub) procedure. Fourth patient with type II aortic insufficiency (due to RCC prolapse) was repaired by HAART 300 implantation and cusp plication. All patients shows good results on 6 months postoperative 3D TTE examinations. Presented technique is reproducible and simplify aortic valve reconstructions.

Display challenges resulting from the use of wide field of view imaging devices

NASA Astrophysics Data System (ADS)

Petty, Gregory J.; Fulton, Jack; Nicholson, Gail; Seals, Ean

2012-06-01

As focal plane array technologies advance and imagers increase in resolution, display technology must outpace the imaging improvements in order to adequately represent the complete data collection. Typical display devices tend to have an aspect ratio similar to 4:3 or 16:9, however a breed of Wide Field of View (WFOV) imaging devices exist that skew from the norm with aspect ratios as high as 5:1. This particular quality, when coupled with a high spatial resolution, presents a unique challenge for display devices. Standard display devices must choose between resizing the image data to fit the display and displaying the image data in native resolution and truncating potentially important information. The problem compounds when considering the applications; WFOV high-situationalawareness imagers are sought for space-limited military vehicles. Tradeoffs between these issues are assessed to the image quality of the WFOV sensor.

Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration

NASA Technical Reports Server (NTRS)

Turner, M. J.; Grande, D. L.

1978-01-01

Based on estimated graphite and boron fiber properties, allowable stresses and strains were established for advanced composite materials. Stiffened panel and conventional sandwich panel concepts were designed and analyzed, using graphite/polyimide and boron/polyimide materials. The conventional sandwich panel was elected as the structural concept for the modified wing structure. Upper and lower surface panels of the arrow wing structure were then redesigned, using high strength graphite/polyimide sandwich panels, retaining the titanium spars and ribs from the prior study. The ATLAS integrated analysis and design system was used for stress analysis and automated resizing of surface panels. Flutter analysis of the hybrid structure showed a significant decrease in flutter speed relative to the titanium wing design. The flutter speed was increased to that of the titanium design by selective increase in laminate thickness and by using graphite fibers with properties intermediate between high strength and high modulus values.

Study of Allocation Guaranteed Time Slot Wireless Body Area Networks Based on IEEE 802.15.4

NASA Astrophysics Data System (ADS)

Yundra, E.; Harsono, G. D.

2018-04-01

This paper aims to determine the size of the Guaranteed Time Slot (GTS) on the super frame structure required for each sensor as well as to know the performance of the GTS resized system compared to the GTS standard on IEEE 802.15.4. This article proposes a scheme to improve IEEE 802.15.4 medium access control, called allocation Guaranteed Time Slot (ALGATIS). ALGATIS is expected to effectively allocate guaranteed time slot to the requested sensors, it adjusts the length of the slot in super frame duration based on the length of the packet data. This article presents a simulation experiment of IEEE 802.15.4, especially for star network, to predict the throughput of networks and average energy consumption. The simulation experiments show that the performance of ALGATIS is better than that of IEEE 802.15.4 standard in term of the throughput of networks and average energy consumption

Application of an optimized winglet configuration to an advanced commercial transport

NASA Technical Reports Server (NTRS)

Shollenberger, C. A.

1979-01-01

The design is presented of an aircraft which employs an integrated wing and winglet lift system. Comparison was made with a conventional baseline configuration employing a high-aspect-ratio supercritical wing. An optimized wing-winglet combination was selected from four proposed configurations for which aerodynamic, structural, and weight characteristics were evaluated. Each candidate wing-winglet configuration was constrained to the same induced drag coefficient as the baseline aircraft. The selected wing-winglet configuration was resized for a specific medium-range mission requirement, and operating costs were estimated for a typical mission. Study results indicated that the wing-winglet aircraft was lighter and could complete the specified mission at less cost than the conventional wing aircraft. These indications were sensitive to the impact of flutter characteristics and, to a lesser extent, to the performance of the high-lift system. Further study in these areas is recommended to reduce uncertainty in future development.

Effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter

NASA Technical Reports Server (NTRS)

Ko, William L.; Olona, Timothy

1987-01-01

The effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter was investigated. Several structural performance and resizing (SPAR) thermal models and NASA structural analysis (NASTRAN) structural models were set up for the orbiter wing midspan bay 3. The thermal model was found to be the one that determines the limit of finite-element fineness because of the limitation of computational core space required for the radiation view factor calculations. The thermal stresses were found to be extremely sensitive to a slight variation of structural temperature distributions. The minimum degree of element fineness required for the thermal model to yield reasonably accurate solutions was established. The radiation view factor computation time was found to be insignificant compared with the total computer time required for the SPAR transient heat transfer analysis.

SPHERES tethered formation flight testbed: advancements in enabling NASA's SPECS mission

NASA Astrophysics Data System (ADS)

Chung, Soon-Jo; Adams, Danielle; Saenz-Otero, Alvar; Kong, Edmund; Miller, David W.; Leisawitz, David; Lorenzini, Enrico; Sell, Steve

2006-06-01

This paper reports on efforts to control a tethered formation flight spacecraft array for NASA's SPECS mission using the SPHERES test-bed developed by the MIT Space Systems Laboratory. Specifically, advances in methodology and experimental results realized since the 2005 SPIE paper are emphasized. These include a new test-bed setup with a reaction wheel assembly, a novel relative attitude measurement system using force torque sensors, and modeling of non-ideal tethers to account for tether vibration modes. The nonlinear equations of motion of multi-vehicle tethered spacecraft with elastic flexible tethers are derived from Lagrange's equations. The controllability analysis indicates that both array resizing and spin-up are fully controllable by the reaction wheels and the tether motor, thereby saving thruster fuel consumption. Based upon this analysis, linear and nonlinear controllers have been successfully implemented on the tethered SPHERES testbed, and tested at the NASA MSFC's flat floor facility using two and three SPHERES configurations.

A general optimality criteria algorithm for a class of engineering optimization problems

NASA Astrophysics Data System (ADS)

Belegundu, Ashok D.

2015-05-01

An optimality criteria (OC)-based algorithm for optimization of a general class of nonlinear programming (NLP) problems is presented. The algorithm is only applicable to problems where the objective and constraint functions satisfy certain monotonicity properties. For multiply constrained problems which satisfy these assumptions, the algorithm is attractive compared with existing NLP methods as well as prevalent OC methods, as the latter involve computationally expensive active set and step-size control strategies. The fixed point algorithm presented here is applicable not only to structural optimization problems but also to certain problems as occur in resource allocation and inventory models. Convergence aspects are discussed. The fixed point update or resizing formula is given physical significance, which brings out a strength and trim feature. The number of function evaluations remains independent of the number of variables, allowing the efficient solution of problems with large number of variables.

System Study: Technology Assessment and Prioritizing Update

NASA Technical Reports Server (NTRS)

2008-01-01

For the Intelligent Engine System (Propulsion 21) study, each technology was evaluated to determine the impact to fuel burn, acoustics, and NOx emissions. The optimum combination of technologies and their overall benefits to the system were also evaluated, resulting in noise improvement potential of 1.89 EPNdB cumulative margin,-1.34 percent fuel burn, and 50 percent NOx reduction from the 2015 UEET-QAT baseline. All the technology evaluations, except T18-20D, were based on newengines, where the engine was resized to obtain the maximum system benefit while maintaining the same cycle parameters as the 2015 UEET-QAT baseline. The impact of turbine clearance control on deteriorated engines, T18-20D, was also evaluated. Recommendations for future system study work include, but were not limited to, validation of a university-developed engine deterioration model and customer value analysis as figures of merit beside fuel burn, emissions, and acoustics.

V/STOL tilt rotor aircraft study. Volume 6: Preliminary design of a composite wing for tilt rotor research aircraft

NASA Technical Reports Server (NTRS)

Soule, V. A.; Badri-Nath, Y.

1973-01-01

The results of a study of the use of composite materials in the wing of a tilt rotor aircraft are presented. An all-metal tilt rotor aircraft was first defined to provide a basis for comparing composite with metal structure. A configuration study was then done in which the wing of the metal aircraft was replaced with composite wings of varying chord and thickness ratio. The results of this study defined the design and performance benefits obtainable with composite materials. Based on these results the aircraft was resized with a composite wing to extend the weight savings to other parts of the aircraft. A wing design was then selected for detailed structural analysis. A development plan including costs and schedules to develop this wing and incorporate it into a proposed flight research tilt rotor vehicle has been devised.

Noise and performance calibration study of a Mach 2.2 supersonic cruise aircraft

NASA Technical Reports Server (NTRS)

Mascitti, V. R.; Maglieri, D. J.

1979-01-01

The baseline configuration of a Mach 2.2 supersonic cruise concept employing a 1980 - 1985 technology level, dry turbojet, mechanically suppressed engine, was calibrated to identify differences in noise levels and performance as determined by the methodology and ground rules used. In addition, economic and noise information is provided consistent with a previous study based on an advanced technology Mach 2.7 configuration, reported separately. Results indicate that the difference between NASA and manufacturer performance methodology is small. Resizing the aircraft to NASA groundrules results in negligible changes in takeoff noise levels (less than 1 EPNdB) but approach noise is reduced by 5.3 EPNdB as a result of increasing approach speed. For the power setting chosen, engine oversizing resulted in no reduction in traded noise. In terms of summated noise level, a 6 EPNdB reduction is realized for a 5% increase in total operating costs.

Society Influencing Science: The role of the Transdisciplinary Advisory Board (TAB) of the European Joint Programming Initiative on Climate.

NASA Astrophysics Data System (ADS)

Noone, K. J.; Manderscheid, P.; Monfray, P.

2017-12-01

It is becoming increasingly apparent that the separation between science and the rest of society is not helping us find solutions to "wicked" problems like climate change or achieving the Sustainable Development Goals. It is clear that a broader approach to research is necessary - one that includes stakeholders in the research process itself. What is unclear is how best to do this. The Transdisciplinary Advisory Board (TAB) of the European Joint Programming Initiative on Climate (JPI Climate) is an example of scientists and stakeholders working together to frame climate research and move the results of scientific research into decision support. JPI Climate is a consortium of 12 European countries (with partners from nine more countries) and is a major funding channel and forum for climate research in Europe. The TAB has an equal number of stakeholders and researchers from 10 different European countries, has an even gender balance, and its members have widely differing backgrounds. The TAB provides input and advice to the governing board of JPI Climate, and influences both the strategic planning for this funding initiative as well as specific calls for proposals issued through the consortium. In addition to its advisory role, the TAB explores the transdisciplinary process itself, expanding the boundaries of how stakeholders and science can interact positively. The TAB is a two-way mechanism through which stakeholders can help improve research and science can help improve society. We will give examples of the spectrum of how the TAB provides mutual influence between stakeholders and science - from helping to draft 10-year research strategies to helping advance the uptake of climate research into the private and policy sectors.

ISA-TAB-Nano: a specification for sharing nanomaterial research data in spreadsheet-based format.

PubMed

Thomas, Dennis G; Gaheen, Sharon; Harper, Stacey L; Fritts, Martin; Klaessig, Fred; Hahn-Dantona, Elizabeth; Paik, David; Pan, Sue; Stafford, Grace A; Freund, Elaine T; Klemm, Juli D; Baker, Nathan A

2013-01-14

The high-throughput genomics communities have been successfully using standardized spreadsheet-based formats to capture and share data within labs and among public repositories. The nanomedicine community has yet to adopt similar standards to share the diverse and multi-dimensional types of data (including metadata) pertaining to the description and characterization of nanomaterials. Owing to the lack of standardization in representing and sharing nanomaterial data, most of the data currently shared via publications and data resources are incomplete, poorly-integrated, and not suitable for meaningful interpretation and re-use of the data. Specifically, in its current state, data cannot be effectively utilized for the development of predictive models that will inform the rational design of nanomaterials. We have developed a specification called ISA-TAB-Nano, which comprises four spreadsheet-based file formats for representing and integrating various types of nanomaterial data. Three file formats (Investigation, Study, and Assay files) have been adapted from the established ISA-TAB specification; while the Material file format was developed de novo to more readily describe the complexity of nanomaterials and associated small molecules. In this paper, we have discussed the main features of each file format and how to use them for sharing nanomaterial descriptions and assay metadata. The ISA-TAB-Nano file formats provide a general and flexible framework to record and integrate nanomaterial descriptions, assay data (metadata and endpoint measurements) and protocol information. Like ISA-TAB, ISA-TAB-Nano supports the use of ontology terms to promote standardized descriptions and to facilitate search and integration of the data. The ISA-TAB-Nano specification has been submitted as an ASTM work item to obtain community feedback and to provide a nanotechnology data-sharing standard for public development and adoption.

ISA-TAB-Nano: A Specification for Sharing Nanomaterial Research Data in Spreadsheet-based Format

PubMed Central

2013-01-01

Background and motivation The high-throughput genomics communities have been successfully using standardized spreadsheet-based formats to capture and share data within labs and among public repositories. The nanomedicine community has yet to adopt similar standards to share the diverse and multi-dimensional types of data (including metadata) pertaining to the description and characterization of nanomaterials. Owing to the lack of standardization in representing and sharing nanomaterial data, most of the data currently shared via publications and data resources are incomplete, poorly-integrated, and not suitable for meaningful interpretation and re-use of the data. Specifically, in its current state, data cannot be effectively utilized for the development of predictive models that will inform the rational design of nanomaterials. Results We have developed a specification called ISA-TAB-Nano, which comprises four spreadsheet-based file formats for representing and integrating various types of nanomaterial data. Three file formats (Investigation, Study, and Assay files) have been adapted from the established ISA-TAB specification; while the Material file format was developed de novo to more readily describe the complexity of nanomaterials and associated small molecules. In this paper, we have discussed the main features of each file format and how to use them for sharing nanomaterial descriptions and assay metadata. Conclusion The ISA-TAB-Nano file formats provide a general and flexible framework to record and integrate nanomaterial descriptions, assay data (metadata and endpoint measurements) and protocol information. Like ISA-TAB, ISA-TAB-Nano supports the use of ontology terms to promote standardized descriptions and to facilitate search and integration of the data. The ISA-TAB-Nano specification has been submitted as an ASTM work item to obtain community feedback and to provide a nanotechnology data-sharing standard for public development and adoption. PMID:23311978

Agreement between digital image analysis and clinical spectrophotometer in CIEL*C*h° coordinate differences and total color difference (ΔE) measurements of dental ceramic shade tabs.

PubMed

Farah, Ra'fat I

2016-01-01

The objectives of this in vitro study were: 1) to test the agreement among color coordinate differences and total color difference (ΔL*, ΔC*, Δh°, and ΔE) measurements obtained by digital image analysis (DIA) and spectrophotometer, and 2) to test the reliability of each method for obtaining color differences. A digital camera was used to record standardized images of each of the 15 shade tabs from the IPS e.max shade guide placed edge-to-edge in a phantom head with a reference shade tab. The images were analyzed using image-editing software (Adobe Photoshop) to obtain the color differences between the middle area of each test shade tab and the corresponding area of the reference tab. The color differences for the same shade tab areas were also measured using a spectrophotometer. To assess the reliability, measurements for the 15 shade tabs were repeated twice using the two methods. The Intraclass Correlation Coefficient (ICC) and the Dahlberg index were used to calculate agreement and reliability. The total agreement of the two methods for measuring ΔL*, ΔC*, Δh°, and ΔE, according to the ICC, exceeded 0.82. The Dahlberg indices for ΔL* and ΔE were 2.18 and 2.98, respectively. For the reliability calculation, the ICCs for the DIA and the spectrophotometer ΔE were 0.91 and 0.94, respectively. High agreement was obtained between the DIA and spectrophotometer results for the ΔL*, ΔC*, Δh°, and ΔE measurements. Further, the reliability of the measurements for the spectrophotometer was slightly higher than the reliability of all measurements in the DIA.

Volume Sensor Canadian Demonstrator Prototype User’s Guide

DTIC Science & Technology

2011-03-23

The “ VSCS ” checkbox controls whether or not all network communications traffic is logged locally for debugging purposes. All of the shown settings...given in the VSCS.Bridge application. On the “Clusters” tab, as shown in Figure 10-4, the information to form the VSCS string ID (SID) are shown...for VSCS communication that is specified on the “Destinations” tab. Changes are committed by pressing the [+] button. On the “Destinations” tab, as

Computational Aeroheating Predictions for Mars Lander Configurations

NASA Technical Reports Server (NTRS)

Edquist, Karl T.; Alter, Stephen J.

2003-01-01

The proposed Mars Science Laboratory (MSL) mission is intended to deliver a large rover to the Martian surface within 10 km of the target site. This paper presents computational fluid dynamics (CFD) predictions of forebody heating rates for two MSL entry configurations with fixed aerodynamic trim tabs. Results are compared to heating on a 70-deg sphere-cone reference geometry. All three heatshield geometries are designed to trim hypersonically at a 16 deg angle of attack in order to generate the lift-to-drag ratio (L/D) required for precision landing. Comparisons between CFD and tunnel data are generally in good agreement for each configuration, but the computations predict more flow separation and higher heating on a trim tab inclined 10 deg relative to the surface. CFD solutions at flight conditions were obtained using an 8-species Mars gas in chemical and thermal nonequilibrium. Laminar and Baldwin-Lomax solutions were used to estimate the effects of the trim tabs and turbulence on heating. A tab extending smoothly from the heatshield flank is not predicted to increase laminar or turbulent heating rates above the reference levels. Laminar heating on a tab deflected 10 deg from the conical heatshield is influenced by flow separation and is up to 35% above the baseline heating rate. The turbulent solution on the inclined tab configuration predicts attached flow and a 43% heating increase above the reference level.

Computational Aeroheating Predictions for Mars Lander Configurations

NASA Technical Reports Server (NTRS)

Edquist, Karl T.; Alter, Stephen J.

2003-01-01

The proposed Mars Science Laboratory (MSL) mission is intended to deliver a large rover to the Martian surface within 10 km of the target site. This paper presents computational fluid dynamics (CFD) predictions of forebody heating rates for two MSL entry configurations with fixed aerodynamic trim tabs. Results are compared to heating on a 70-deg sphere-cone reference geometry. All three heatshield geometries are designed to trim hypersonically at a 16 deg angle of attack in order to generate the lift-to-drag ratio (LID) required for precision landing. Comparisons between CFD and tunnel data are generally in good agreement for each configuration, but the computations predict more flow separation and higher heating on a trim tab inclined 10 deg relative to the surface. CFD solutions at flight conditions were obtained using an 8-species Mars gas in chemical and thermal non-equilibrium. Laminar and Baldwin-Lomax solutions were used to estimate the effects of the trim tabs and turbulence on heating. A tab extending smoothly from the heatshield flank is not predicted to increase laminar or turbulent heating rates above the reference levels. Laminar heating on a tab deflected 10 deg from the conical heatshield is influenced by flow separation and is up to 35% above the baseline heating rate. The turbulent solution on the inclined tab configuration predicts attached flow and a 43% heating increase above the reference level.

Subsonic Jet Noise from Non-Axisymmetric and Tabbed Nozzles

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.; Tam, Christopher K. W.

1999-01-01

Subsonic jet noise from non-axisymmetric and tabbed nozzles are investigated experimentally and theoretically. It is shown that the noise spectra of these jets are in good agreement with the similarity spectra found empirically earlier by Tam, Golebiowski and Seiner through a detailed analysis of supersonic jet noise data. Further, the radiated noise fields of the jets under study, including elliptic and large aspect ratio rectangular jets, are found to be quite axisymmetric and are practically the same as that of a circular jet with the same exit area. These experimental results strongly suggest that nozzle geometry modification into elliptic or rectangular shapes is not an effective method for jet noise suppression. A lobed nozzle, on the other hand, is found to significantly impact the noise field. Noise from large scale turbulent structures, radiating principally in the downstream direction, is effectively suppressed. Tabs also impact the noise field, primarily by shifting the spectral peak to a higher frequency. A jetlets model is developed to provide a basic understanding of the noise from tabbed jets. The model predicts that the noise spectrum from a jet with N tabs (N > 2) can be obtained from that of the original jet (no tab) by a simple frequency shift. The shifted frequency is obtained by multiplying the original frequency by N(sup 1/2). This result is in fairly good agreement with experimental data.

Subsonic Jet Noise from Non-Axisymmetric and Tabbed Nozzles

NASA Technical Reports Server (NTRS)

Tam, Christopher K. W.; Zaman, K. B. M. Q.

1999-01-01

Subsonic jet noise from non-axisymmetric and tabbed nozzles are investigated experimentally and theoretically. It is shown that the noise spectra of these jets are in good agreement with the similarity spectra found empirically earlier by Tam, Golebiowski and Seiner through a detailed analysis of supersonic jet noise data. Further, the radiated noise fields of the jets under study, including elliptic and large aspect ratio rectangular jets, are found to be quite axisymmetric and are practically the same as that of a circular jet with the same exit area. These experimental results strongly suggest that nozzle geometry modification into elliptic or rectangular shapes is not an effective method for jet noise suppression. A lobed nozzle, on the other hand, is found to significantly impact the noise field. Noise from large scale turbulent structures, radiating principally in the downstream direction, is effectively suppressed. Tabs also impact the noise field, primarily by shifting the spectral peak to a higher frequency. A jetlets model is developed to provide a basic understanding of the noise from tabbed jets. The model predicts that the noise spectrum from a jet with N tabs (N greater than or equal to 2) can be obtained from that of the original jet (no tab) by a simple frequency shift. The shifted frequency is obtained by multiplying the original frequency by N(exp 1/2). This result is in fairly good agreement with experimental data.

The reliability and validity of the Tokyo Autistic Behaviour Scale.

PubMed

Kurita, H; Miyake, Y

1990-03-01

The Tokyo Autistic Behavior Scale (TABS) consisting of 39 items provisionally grouped in four areas--interpersonal-social relationship, language-communication, habit-mannerism and others--is an instrument used by a child's caretaker to rate the child's autistic behaviors on a 3-point scale. Test-retest reliability was satisfactory (i.e., an r for a total score was .94). Among six DSM-III diagnostic groups, infantile autism showed a significantly higher total TABS score than the other five groups, and a taxonomic validity coefficient was .54. An r between total scores of the TABS and the Childhood Autism Rating Scale--Tokyo Version was .59. The area scores showed a lower validity than the total score. The TABS appears to be a useful instrument to assess autistic behavior.

Combining Stereo SECCHI COR2 and HI1 Images for Automatic CME Front Edge Tracking

NASA Technical Reports Server (NTRS)

Kirnosov, Vladimir; Chang, Lin-Ching; Pulkkinen, Antti

2016-01-01

COR2 coronagraph images are the most commonly used data for coronal mass ejection (CME) analysis among the various types of data provided by the STEREO (Solar Terrestrial Relations Observatory) SECCHI (Sun-Earth Connection Coronal and Heliospheric Investigation) suite of instruments. The field of view (FOV) in COR2 images covers 215 solar radii (Rs) that allow for tracking the front edge of a CME in its initial stage to forecast the lead-time of a CME and its chances of reaching the Earth. However, estimating the lead-time of a CME using COR2 images gives a larger lead-time, which may be associated with greater uncertainty. To reduce this uncertainty, CME front edge tracking should be continued beyond the FOV of COR2 images. Therefore, heliospheric imager (HI1) data that covers 1590 Rs FOV must be included. In this paper, we propose a novel automatic method that takes both COR2 and HI1 images into account and combine the results to track the front edges of a CME continuously. The method consists of two modules: pre-processing and tracking. The pre-processing module produces a set of segmented images, which contain the signature of a CME, for both COR2 and HI1 separately. In addition, the HI1 images are resized and padded, so that the center of the Sun is the central coordinate of the resized HI1 images. The resulting COR2 andHI1 image set is then fed into the tracking module to estimate the position angle (PA) and track the front edge of a CME. The detected front edge is then used to produce a height-time profile that is used to estimate the speed of a CME. The method was validated using 15 CME events observed in the period from January 1, 2008 to August 31, 2009. The results demonstrate that the proposed method is effective for CME front edge tracking in both COR2 and HI1 images. Using this method, the CME front edge can now be tracked automatically and continuously in a much larger range, i.e., from 2 to 90 Rs, for the first time. These improvement scan greatly help in making the quantitative CME analysis more accurate and have the potential to assist in space weather forecasting.

Airplane automatic control force trimming device for asymmetric engine failures

NASA Technical Reports Server (NTRS)

Stewart, Eric C. (Inventor)

1987-01-01

The difference in dynamic pressure in the propeller slipstreams as measured by sensors is divided by the freestream dynamic pressure generating a quantity proportional to the differential thrust coefficient. This quantity is used to command an electric trim motor to change the position of trim tab thereby retrimming the airplane to the new asymmetric power condition. The change in position of the trim tab produced by the electric trim motor is summed with the pilot's input to produce the actual trim tab position.

Mechanical support of a ceramic gas turbine vane ring

DOEpatents

Shi, Jun; Green, Kevin E.; Mosher, Daniel A.; Holowczak, John E.; Reinhardt, Gregory E.

2010-07-27

An assembly for mounting a ceramic turbine vane ring onto a turbine support casing comprises a first metal clamping ring and a second metal clamping ring. The first metal clamping ring is configured to engage with a first side of a tab member of the ceramic turbine vane ring. The second metal clamping ring is configured to engage with a second side of the tab member such that the tab member is disposed between the first and second metal clamping rings.

Status of Standardization Projects, Quarter Ending 30 June 1992

DTIC Science & Technology

1992-06-30

6505 5697 A-A-XXX AMINO ACIDS, INJECT MB ON F2 A 922 932 932 A MO MS 03 N 6505 5698 A-A-XXX SIMETHICONE TABS MB DM F4 A 922 932 932 A MD MS 03 N 6505...4 F2 A 922 932 932 A MD MS 03 N 5505 5698 A-A-XXX SIMETHICONE TABS MB 094 F4 A 922 932 932 A MD MS 03 N 5505 5699 U-N-210A SIMETHCONE TABS MB 09 H5

Finger-Circumference-Measuring Device

NASA Technical Reports Server (NTRS)

Le, Suy

1995-01-01

Easy-to-use device quickly measures circumference of finger (including thumb) on human hand. Includes polytetrafluoroethylene band 1/8 in. wide, bent into loop and attached to tab that slides on scale graduated in millimeters. Sliding tab preloaded with constant-force tension spring, which pulls tab toward closure of loop. Designed to facilitate measurements at various points along fingers to obtain data for studies of volumetric changes of fingers in microgravity. Also used in normal Earth gravity studies of growth and in assessment of diseases like arthritis.

Erythrocyte Sedimentation Rate (ESR)

MedlinePlus

... 3 screens]. Available from: https://labtestsonline.org/understanding/analytes/esr/tab/test/ Lab Tests Online [Internet]. Washington ... 2 screens]. Available from: https://labtestsonline.org/understanding/analytes/esr/tab/sample/ National Heart, Lung, and Blood ...

EL PROTEOMA DEL TEJIDO ADIPOSO SUBCUTÁNEO MUESTRA HETEROGENEIDAD ANATÓMICA

PubMed Central

Martos-Moreno, G.A.; Sackmann-Sala, L.; Berryman, D.E.; Blome, D.W.; Argente, J.; Kopchick, y J.J.

2015-01-01

Introducción El tejido adiposo blanco (TAB) subcutáneo (Sc) humano podría variar dependiendo de su localización anatómica, con diferencias en su perfil proteómico. Pacientes y métodos Se obtuvieron aspirados de TAB-Sc de seis mujeres con IMC >25 kg/m2, sometidas a liposucción. Dicho TAB-Sc se obtuvo de seis localizaciones anatómicas: abdominal superior e inferior, muslo, dorsal, flanco y cadera, analizándose su perfil proteómico mediante electroforesis bidimensional. En muslo y abdomen superior se compararon, además, las muestras obtenidas de las dos capas del TAB-Sc (profunda y superficial). Resultados Se detectaron 21 proteínas que mostraban una intensidad de expresión diferente entre las seis localizaciones anatómicas y 14 entre las capas superficial y profunda de una misma región. Entre las proteínas identificadas se incluyen: vimentina (proteína estructural); proteínas “heat-shock” (HSPs), superóxido-dismutasa, (estrés/chaperoninas); proteína fijadora de ácidos grasos 4 (FABP-4) y alfa-enolasa (metabolismo lipídico y de los hidratos de carbono, respectivamente) y ATP-sintetasa (producción de energía). Entre las regiones estudiadas, el TAB-Sc dorsal mostraba un perfil proteómico particular, con menor expresión de proteínas implicadas en la producción de energía y metabolismo (ATP-sintetasa, alfa-enolasa, HSPs y FABP-4) que el resto de regiones. Conclusiones Los niveles de expresión de diversas proteínas en el TAB-Sc humano no son homogéneos, difiriendo entre localizaciones anatómicas. Esto sugiere la existencia de diferencias funcionales en el TAB-Sc de acuerdo con su localización anatómica, lo que debe considerarse antes de asumir la extrapolación de los datos derivados del TAB-Sc de una determinada localización al de otras partes de la anatomía. PMID:23228439

Value of supervised learning events in predicting doctors in difficulty.

PubMed

Patel, Mumtaz; Agius, Steven; Wilkinson, Jack; Patel, Leena; Baker, Paul

2016-07-01

In the UK, supervised learning events (SLE) replaced traditional workplace-based assessments for foundation-year trainees in 2012. A key element of SLEs was to incorporate trainee reflection and assessor feedback in order to drive learning and identify training issues early. Few studies, however, have investigated the value of SLEs in predicting doctors in difficulty. This study aimed to identify principles that would inform understanding about how and why SLEs work or not in identifying doctors in difficulty (DiD). A retrospective case-control study of North West Foundation School trainees' electronic portfolios was conducted. Cases comprised all known DiD. Controls were randomly selected from the same cohort. Free-text supervisor comments from each SLE were assessed for the four domains defined in the General Medical Council's Good Medical Practice Guidelines and each scored blindly for level of concern using a three-point ordinal scale. Cumulative scores for each SLE were then analysed quantitatively for their predictive value of actual DiD. A qualitative thematic analysis was also conducted. The prevalence of DiD in this sample was 6.5%. Receiver operator characteristic curve analysis showed that Team Assessment of Behaviour (TAB) was the only SLE strongly predictive of actual DiD status. The Educational Supervisor Report (ESR) was also strongly predictive of DiD status. Fisher's test showed significant associations of TAB and ESR for both predicted and actual DiD status and also the health and performance subtypes. None of the other SLEs showed significant associations. Qualitative data analysis revealed inadequate completion and lack of constructive, particularly negative, feedback. This indicated that SLEs were not used to their full potential. TAB and the ESR are strongly predictive of DiD. However, SLEs are not being used to their full potential, and the quality of completion of reports on SLEs and feedback needs to be improved in order to better identify and manage DiD. © 2016 John Wiley & Sons Ltd.

Collaborators | Office of Cancer Genomics

Cancer.gov

The TARGET initiative is jointly managed within the National Cancer Institute (NCI) by the Office of Cancer Genomics (OCG)Opens in a New Tab and the Cancer Therapy Evaluation Program (CTEP)Opens in a New Tab.

In vitro model to evaluate reliability and accuracy of a dental shade-matching instrument.

PubMed

Kim-Pusateri, Seungyee; Brewer, Jane D; Dunford, Robert G; Wee, Alvin G

2007-11-01

There are several electronic shade-matching instruments available for clinical use; unfortunately, there are limited acceptable in vitro models to evaluate their reliability and accuracy. The purpose of this in vitro study was to evaluate the reliability and accuracy of a dental clinical shade-matching instrument. Using the shade-matching instrument (ShadeScan), color measurements were made of 3 commercial shade guides (VITA Classical, VITA 3D-Master, and Chromascop). Shade tabs were selected and placed in the middle of a gingival matrix (Shofu Gummy), with tabs of the same nominal shade from additional shade guides placed on both sides. Measurements were made of the central region of the shade tab inside a black box. For the reliability assessment, each shade tab from each of the 3 shade guide types was measured 10 times. For the accuracy assessment, each shade tab from 10 guides of each of the 3 types evaluated was measured once. Reliability, accuracy, and 95% confidence intervals were calculated for each shade tab. Differences were determined by 1-way ANOVA followed by the Bonferroni multiple comparison procedure. Reliability of ShadeScan was as follows: VITA Classical = 95.0%, VITA 3D-Master = 91.2%, and Chromascop = 76.5%. Accuracy of ShadeScan was as follows: VITA Classical = 65.0%, VITA 3D-Master = 54.2%, Chromascop = 84.5%. This in vitro study showed a varying degree of reliability and accuracy for ShadeScan, depending on the type of shade guide system used.

Individualized FAC on bottom tab subassemblies to minimize adhesive gap between emitter and optics

NASA Astrophysics Data System (ADS)

Sauer, Sebastian; Müller, Tobias; Haag, Sebastian; Beleke, Andreas; Zontar, Daniel; Baum, Christoph; Brecher, Christian

2017-02-01

High Power Diode Laser (HPDL) systems with short focal length fast-axis collimators (FAC) require submicron assembly precision. Conventional FAC-Lens assembly processes require adhesive gaps of 50 microns or more in order to compensate for component tolerances (e.g. deviation of back focal length) and previous assembly steps. In order to control volumetric shrinkage of fast-curing UV-adhesives shrinkage compensation is mandatory. The novel approach described in this paper aims to minimize the impact of volumetric shrinkage due to the adhesive gap between HPDL edge emitters and FAC-Lens. Firstly, the FAC is actively aligned to the edge emitter without adhesives or bottom tab. The relative position and orientation of FAC to emitter are measured and stored. Consecutively, an individual subassembly of FAC and bottom tab is assembled on Fraunhofer IPT's mounting station with a precision of +/-1 micron. Translational and lateral offsets can be compensated, so that a narrow and uniform glue gap for the consecutive bonding process of bottom tab to heatsink applies (Figure 4). Accordingly, FAC and bottom tab are mounted to the heatsink without major shrinkage compensation. Fraunhofer IPT's department assembly of optical systems and automation has made several publications regarding active alignment of FAC lenses [SPIE LASE 8241-12], volumetric shrinkage compensation [SPIE LASE 9730-28] and FAC on bottom tab assembly [SPIE LASE 9727-31] in automated production environments. The approach described in this paper combines these and is the logical continuation of that work towards higher quality of HPDLs.

Assessment of airborne environmental bacteria and related factors in 25 underground railway stations in Seoul, Korea

NASA Astrophysics Data System (ADS)

Hwang, Sung Ho; Yoon, Chung Sik; Ryu, Kyong Nam; Paik, Samuel Y.; Cho, Jun Ho

2010-05-01

This study assessed bacterial concentrations in indoor air at 25 underground railway stations in Seoul, Korea, and investigated various related factors including the presence of platform screen doors (PSD), depth of the station, year of construction, temperature, relative humidity, and number of passengers. A total of 72 aerosol samples were collected from all the stations. Concentrations of total airborne bacteria (TAB) ranged from not detected (ND) to 4997 CFU m -3, with an overall geometric mean (GM) of 191 CFU m -3. Airborne bacteria were detected at 23 stations (92%) and Gram-negative bacteria (GNB) were detected at two stations (8%). TAB concentrations of four stations (16%) exceeded 800 CFU m -3, the Korea indoor bio-aerosol guideline. The results of the study showed that TAB concentrations at the stations without PSD showed higher TAB concentrations than those with PSD, though not at statistically significant levels. TAB concentrations of deeper stations revealed significantly higher levels than those of shallower stations. Based on this study, it is recommended that mitigation measures be applied to improve the indoor air quality (IAQ) of underground railway stations in Seoul, with focused attention on deeper stations.

Improved Quick-Release Pin Mechanism

NASA Technical Reports Server (NTRS)

Wright, Jay M.

2007-01-01

An improved quick-release pin mechanism supplants a prior such mechanism in which the pin bears a shear load to hold two objects together. The prior mechanism, of a ball-locking design, can fail when vibrations cause balls to fall out. The load-bearing pin is an outer tube with a handle at one end (hereafter denoted the near end). Within the outer tube is a spring-loaded inner tube that includes a handle at its near end and a pivoting tab at its far end. The pin is inserted through holes in the objects to be retained and the inner tube is pushed against an offset pivot inside the outer tube to make the tab rotate outward so that it protrudes past the outer diameter of the outer tube, and the spring load maintains this configuration so that the pin cannot be withdrawn through the holes. Pushing the handles together against the spring load moves the locking tab out far enough that the tab becomes free to rotate inward. Then releasing the inner-tube handle causes the tab to be pulled into a resting position inside the outer tube. The pin can then be pulled out through the holes.

An ISA-TAB-Nano based data collection framework to support data-driven modelling of nanotoxicology.

PubMed

Marchese Robinson, Richard L; Cronin, Mark T D; Richarz, Andrea-Nicole; Rallo, Robert

2015-01-01

Analysis of trends in nanotoxicology data and the development of data driven models for nanotoxicity is facilitated by the reporting of data using a standardised electronic format. ISA-TAB-Nano has been proposed as such a format. However, in order to build useful datasets according to this format, a variety of issues has to be addressed. These issues include questions regarding exactly which (meta)data to report and how to report them. The current article discusses some of the challenges associated with the use of ISA-TAB-Nano and presents a set of resources designed to facilitate the manual creation of ISA-TAB-Nano datasets from the nanotoxicology literature. These resources were developed within the context of the NanoPUZZLES EU project and include data collection templates, corresponding business rules that extend the generic ISA-TAB-Nano specification as well as Python code to facilitate parsing and integration of these datasets within other nanoinformatics resources. The use of these resources is illustrated by a "Toy Dataset" presented in the Supporting Information. The strengths and weaknesses of the resources are discussed along with possible future developments.

An ISA-TAB-Nano based data collection framework to support data-driven modelling of nanotoxicology

PubMed Central

Marchese Robinson, Richard L; Richarz, Andrea-Nicole; Rallo, Robert

2015-01-01

Summary Analysis of trends in nanotoxicology data and the development of data driven models for nanotoxicity is facilitated by the reporting of data using a standardised electronic format. ISA-TAB-Nano has been proposed as such a format. However, in order to build useful datasets according to this format, a variety of issues has to be addressed. These issues include questions regarding exactly which (meta)data to report and how to report them. The current article discusses some of the challenges associated with the use of ISA-TAB-Nano and presents a set of resources designed to facilitate the manual creation of ISA-TAB-Nano datasets from the nanotoxicology literature. These resources were developed within the context of the NanoPUZZLES EU project and include data collection templates, corresponding business rules that extend the generic ISA-TAB-Nano specification as well as Python code to facilitate parsing and integration of these datasets within other nanoinformatics resources. The use of these resources is illustrated by a “Toy Dataset” presented in the Supporting Information. The strengths and weaknesses of the resources are discussed along with possible future developments. PMID:26665069

Collaborators | Office of Cancer Genomics

Cancer.gov

The TARGET initiative has been jointly managed within the National Cancer Institute (NCI) by the Office of Cancer Genomics (OCG)Opens in a New Tab and the Cancer Therapy Evaluation Program (CTEP)Opens in a New Tab.

Effect of Delta Tabs on Free Jets from Complex Nozzles

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

2001-01-01

Effects of 'delta-tabs' on the mixing and noise characteristics of two model-scale nozzles have been investigated experimentally. The two models are (1) an eight-lobed nozzle simulating the primary flow of a mixer-ejector configuration considered for the HSCT program, (2) an axisymmetric nozzle with a centerbody simulating the 'ACE' configuration also considered for the HSCT program. Details of the flow-field for model (1) are explored, while primarily the noise-field is explored for model (2). Effects of different tab configurations are documented.

High-Throughput Synthetic Chemistry Enabled by Organic Solvent Disintegrating Tablet.

PubMed

Li, Tingting; Xu, Lei; Xing, Yanjun; Xu, Bo

2017-01-17

Synthetic chemistry remains a time- and labor-intensive process of inherent hazardous nature. Our organic solvent disintegrating tablet (O-Tab) technology has shown potential to make industrial/synthetic chemistry more efficient. As is the case with pharmaceutical tablets, our reagent-containing O-Tabs are mechanically strong, but disintegrate rapidly when in contact with reaction media (organic solvents). For O-Tabs containing sensitive chemicals, they can be further coated to insulate them from air and moisture. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reusable pipe flange covers

DOEpatents

Holden, James Elliott; Perez, Julieta

2001-01-01

A molded, flexible pipe flange cover for temporarily covering a pipe flange and a pipe opening includes a substantially round center portion having a peripheral skirt portion depending from the center portion, the center portion adapted to engage a front side of the pipe flange and to seal the pipe opening. The peripheral skirt portion is formed to include a plurality of circumferentially spaced tabs, wherein free ends of the flexible tabs are formed with respective through passages adapted to receive a drawstring for pulling the tabs together on a back side of the pipe flange.

The role of ZIP transporters and group F bZIP transcription factors in the Zn-deficiency response of wheat (Triticum aestivum).

PubMed

Evens, Nicholas P; Buchner, Peter; Williams, Lorraine E; Hawkesford, Malcolm J

2017-10-01

Understanding the molecular basis of zinc (Zn) uptake and transport in staple cereal crops is critical for improving both Zn content and tolerance to low-Zn soils. This study demonstrates the importance of group F bZIP transcription factors and ZIP transporters in responses to Zn deficiency in wheat (Triticum aestivum). Seven group F TabZIP genes and 14 ZIPs with homeologs were identified in hexaploid wheat. Promoter analysis revealed the presence of Zn-deficiency-response elements (ZDREs) in a number of the ZIPs. Functional complementation of the zrt1/zrt2 yeast mutant by TaZIP3, -6, -7, -9 and -13 supported an ability to transport Zn. Group F TabZIPs contain the group-defining cysteine-histidine-rich motifs, which are the predicted binding site of Zn 2+ in the Zn-deficiency response. Conservation of these motifs varied between the TabZIPs suggesting that individual TabZIPs may have specific roles in the wheat Zn-homeostatic network. Increased expression in response to low Zn levels was observed for several of the wheat ZIPs and bZIPs; this varied temporally and spatially suggesting specific functions in the response mechanism. The ability of the group F TabZIPs to bind to specific ZDREs in the promoters of TaZIPs indicates a conserved mechanism in monocots and dicots in responding to Zn deficiency. In support of this, TabZIPF1-7DL and TabZIPF4-7AL afforded a strong level of rescue to the Arabidopsis hypersensitive bzip19 bzip23 double mutant under Zn deficiency. These results provide a greater understanding of Zn-homeostatic mechanisms in wheat, demonstrating an expanded repertoire of group F bZIP transcription factors, adding to the complexity of Zn homeostasis. © 2017 The Authors The Plant Journal published by John Wiley & Sons Ltd and Society for Experimental Biology.

Survivability of Affordable High Temperature Polymer Matrix Composites for Propulsion Engine Components

NASA Technical Reports Server (NTRS)

Dean, Derrick; Haque, Anwar; Vaidya, Uday; Meador, Michael A. (Technical Monitor)

2003-01-01

PMR-type polyimides are regarded as state of the art high temperature polymers, due to their excellent thermo-mechanical properties and thermo-oxidative stability. One of their drawbacks, however is the inability to process them using cost-effective processing methods such as Resin Transfer Molding (RTM) and Resin Film Infusion (RFI). Development of low viscosity, high temperature polymers has been the subject of intense research. Recently, a new generation of low viscosity polyimides were synthesized by the introduction of twisted biphenyl or binapthyl groups into the backbone. This report details the progress for Year 1, which has involved acquiring samples and initiating Phases I and II of the proposed research. Specifically, studies of the process-property relationships of a series of polymers using oligomers based on 2,3,3' ,4'-biphenyltertracarboxylic dianhydride (PBDA) and a mixture of a diamine, BAX and a triamine, 1,3,5-Tris (4-aminophenoxybenzene), TAB, where the amount of TAB was varied have been initiated. The sample containing 10 percent TAB possesses a slightly higher degree of crystalline order versus that of the 20 percent TAB sample, based on x-ray diffraction studies of the b-staged oligomers. Both systems lose all of the crystalline order upon curing, however. The chemorheology has been studied as a function of the TAB content. While the magnitude of the viscosity is essentially the same for both systems, the cure kinetics of the 10 percent TAB system is faster than that for the 20 percent TAB system. The sample exhibits a melting-recrystallization-remelting behavior before the crosslinking commences. Correlation of other kinetic parameters, such as the activation energies for curing, the Tg and mechanical properties to the structure of these systems is underway. Future studies will involve characterization of mechanical and thermal properties of the pure resins and the fabrication of fiber reinforced composites using these materials.

Numerical Simulation of Liquid Jet Atomization Including Turbulence Effects

NASA Technical Reports Server (NTRS)

Trinh, Huu P.; Chen, C. P.; Balasubramanyam, M. S.

2005-01-01

This paper describes numerical implementation of a newly developed hybrid model, T-blob/T-TAB, into an existing computational fluid dynamics (CFD) program for primary and secondary breakup simulation of liquid jet atomization. This model extend two widely used models, the Kelvin-Helmholtz (KH) instability of Reitz (blob model) and the Taylor-Analogy-Breakup (TAB) secondary droplet breakup by O'Rourke and Amsden to include turbulence effects. In the primary breakup model, the level of the turbulence effect on the liquid breakup depends on the characteristic scales and the initial flow conditions. For the secondary breakup, an additional turbulence force acted on parent drops is modeled and integrated into the TAB governing equation. Several assessment studies are presented and the results indicate that the existing KH and TAB models tend to under-predict the product drop size and spray angle, while the current model provides superior results when compared with the measured data.

User’s Manual for the Generalized Computer Program System Open-Channel Flow and Sedimentation TABS-2. Main Text and Appendices A through O.

DTIC Science & Technology

1985-08-01

American Society of Civil Engineers,, No. HYIL. Ariathurai, R. 1974 (Aug). A Finite Element Model for Sediment Transport in Estuaries, Ph. D. Thesis ...11 aml ms po GR PH C 1.2 ś, I i 2 "’-..04/85 a I -- . a.., 4 4 - 4 I --.. - £ . ,. 04/85 4 444 4 9*4*4449 444 A4 A44 4 4 4 4 4 4 * 4 44 4 4 4 p 4...VEL MAGNITUDE (HOURS) CFT /SEC) (FT/SEC) (F/SEC) (FT) (FT) STATUS (FiSEC) (FT/SEC) (FT/SEC) .00 -. 115 -. 043 -. 123 5.501 100.507 MET -. 112 -. 069

Deadly Throwaways--Plastic Six-Pack Binders and Metal Pull-Tabs Doom Wildlife

ERIC Educational Resources Information Center

Ward, Penny

1975-01-01

Thousands of creatures are vulnerable to entrapment, entanglement, strangulation, or starvation as a result of plastic six-pack binders and metal pull-tabs. Possible solutions include: recycling, clean-up campaigns, and strong container legislation. (BT)

Giant cell arteritis: diagnostic accuracy of MR imaging of superficial cranial arteries in initial diagnosis-results from a multicenter trial.

PubMed

Klink, Thorsten; Geiger, Julia; Both, Marcus; Ness, Thomas; Heinzelmann, Sonja; Reinhard, Matthias; Holl-Ulrich, Konstanze; Duwendag, Dirk; Vaith, Peter; Bley, Thorsten Alexander

2014-12-01

To assess the diagnostic accuracy of contrast material-enhanced magnetic resonance (MR) imaging of superficial cranial arteries in the initial diagnosis of giant cell arteritis ( GCA giant cell arteritis ). Following institutional review board approval and informed consent, 185 patients suspected of having GCA giant cell arteritis were included in a prospective three-university medical center trial. GCA giant cell arteritis was diagnosed or excluded clinically in all patients (reference standard [final clinical diagnosis]). In 53.0% of patients (98 of 185), temporal artery biopsy ( TAB temporal artery biopsy ) was performed (diagnostic standard [ TAB temporal artery biopsy ]). Two observers independently evaluated contrast-enhanced T1-weighted MR images of superficial cranial arteries by using a four-point scale. Diagnostic accuracy, involvement pattern, and systemic corticosteroid ( sCS systemic corticosteroid ) therapy effects were assessed in comparison with the reference standard (total study cohort) and separately in comparison with the diagnostic standard TAB temporal artery biopsy ( TAB temporal artery biopsy subcohort). Statistical analysis included diagnostic accuracy parameters, interobserver agreement, and receiver operating characteristic analysis. Sensitivity of MR imaging was 78.4% and specificity was 90.4% for the total study cohort, and sensitivity was 88.7% and specificity was 75.0% for the TAB temporal artery biopsy subcohort (first observer). Diagnostic accuracy was comparable for both observers, with good interobserver agreement ( TAB temporal artery biopsy subcohort, κ = 0.718; total study cohort, κ = 0.676). MR imaging scores were significantly higher in patients with GCA giant cell arteritis -positive results than in patients with GCA giant cell arteritis -negative results ( TAB temporal artery biopsy subcohort and total study cohort, P < .001). Diagnostic accuracy of MR imaging was high in patients without and with sCS systemic corticosteroid therapy for 5 days or fewer (area under the curve, ≥0.9) and was decreased in patients receiving sCS systemic corticosteroid therapy for 6-14 days. In 56.5% of patients with TAB temporal artery biopsy -positive results (35 of 62), MR imaging displayed symmetrical and simultaneous inflammation of arterial segments. MR imaging of superficial cranial arteries is accurate in the initial diagnosis of GCA giant cell arteritis . Sensitivity probably decreases after more than 5 days of sCS systemic corticosteroid therapy; thus, imaging should not be delayed. Clinical trial registration no. DRKS00000594 . © RSNA, 2014.

miR-342-3p affects hepatocellular carcinoma cell proliferation via regulating NF-κB pathway

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Liang; Zhang, Yubao, E-mail: zhyb880077@sina.com

2015-02-13

Recent research indicates that non-coding microRNAs (miRNAs) help regulate basic cellular processes in many types of cancer cells. We hypothesized that overexpression of miR-342-3p might affect proliferation of hepatocellular carcinoma (HCC) cells. After confirming overexpression of miR-342-3p with qRT-PCR, MTT assay showed that HCC cell proliferation was significantly inhibited by miR-342-3p, and that it significantly decreased BrdU-positive cell proliferation by nearly sixfold. Searching for targets using three algorithms we found that miR-342-3p is related to the NF-κB pathway and luciferase assay found that IKK-γ, TAB2 and TAB3 are miR-342-3p target genes. Results of western blot on extracted nuclear proteins ofmore » HepG2 and HCT-116 cells showed that miR-342-3p reduced and miR-342-3p-in increased p65 nuclear levels and qRT-PCR found that NF-κB pathway downstream genes were downregulated by miR-342-3p and upregulated by miR-342-3p-in, confirming that miR-342 targets NF-κB pathway. Overexpression of Ikk-γ, TAB2 and TAB3 partially rescued HCC cells proliferation inhibited by miR-342-3p. Using the GSE54751 database we evaluated expression from 10 HCC samples, which strongly suggested downregulation of miR-342-3p and we also found inverse expression between miR-342-3p and its targets IKK-γ, TAB2 and TAB3 from 71 HCC samples. Our results show that miR-342-3p has a significant role in HCC cell proliferation and is suitable for investigation of therapeutic targets. - Highlights: • MiR-342-3p suppresses hepatocellular carcinoma cell proliferation. • MiR-342-3p targets IKK-γ, TAB2 and TAB3 genes. • MiR-342-3p downregulates NF-kB signaling pathway. • MiR-342-3p is downregulated in clinical hepatocellular carcinoma samples. • The expression of miR-342-3p and its target gene is inversely related.« less

Trust It or Trash It?

MedlinePlus

Trust It or Trash It? About | Contact | Español Tab 1 Tab 2 What is Trust It or Trash It? This is a tool ... be true, it may be. (See the second “Trust it” statement above). Click on each element below ...

Eddy-Current Inspection Of Tab Seals On Beverage Cans

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph

1994-01-01

Eddy-current inspection system monitors tab seals on beverage cans. Device inspects all cans at usual production rate of 1,500 to 2,000 cans per minute. Automated inspection of all units replaces visual inspection by microscope aided by mass spectrometry. System detects defects in real time. Sealed cans on conveyor pass near one of two coils in differential eddy-current probe. Other coil in differential eddy-current probe positioned near stationary reference can on which tab seal is known to be of acceptable quality. Signal of certain magnitude at output of probe indicates defective can, automatically ejected from conveyor.

Automatic system testing of a decision support system for insulin dosing using Google Android.

PubMed

Spat, Stephan; Höll, Bernhard; Petritsch, Georg; Schaupp, Lukas; Beck, Peter; Pieber, Thomas R

2013-01-01

Hyperglycaemia in hospitalized patients is a common and costly health care problem. The GlucoTab system is a mobile workflow and decision support system, aiming to facilitate efficient and safe glycemic control of non-critically ill patients. Being a medical device, the GlucoTab requires extensive and reproducible testing. A framework for high-volume, reproducible and automated system testing of the GlucoTab system was set up applying several Open Source tools for test automation and system time handling. The REACTION insulin titration protocol was investigated in a paper-based clinical trial (PBCT). In order to validate the GlucoTab system, data from this trial was used for simulation and system tests. In total, 1190 decision support action points were identified and simulated. Four data points (0.3%) resulted in a GlucoTab system error caused by a defective implementation. In 144 data points (12.1%), calculation errors of physicians and nurses in the PBCT were detected. The test framework was able to verify manual calculation of insulin doses and detect relatively many user errors and workflow anomalies in the PBCT data. This shows the high potential of the electronic decision support application to improve safety of implementation of an insulin titration protocol and workflow management system in clinical wards.

77 FR 24425 - Airworthiness Directives; Empresa Brasileria de Aeronáutica S.A. (EMBRAER) Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-24

... next 24 months after the effective date of this AD, rework the ailerons, ailerons trim-tabs, ailerons... effective date of this AD, rework the ailerons, ailerons trim-tabs, ailerons horn cover, rudder, rudder trim... 24427

The linear shade guide design of Vita 3D-master performs as well as the original design of the Vita 3D-master.

PubMed

Corcodel, N; Rammelsberg, P; Jakstat, H; Moldovan, O; Schwarz, S; Hassel, A J

2010-11-01

Visual tooth colour assessment by use of the Vita 3D-Master(®) (3D; Vita Zahnfabrik, Bad Säckingen, Germany) is well documented. To improve handling, a new linear arrangement of the shade tabs has been introduced (LG; Linearguide 3D-Master(®) ). The purpose of this study was to investigate whether the linear design has an effect on shade matching. Fifty-six students underwent identical, theoretical and practical training, by use of an Internet learning module [Toothguide Training Software(®) (TT)] and a standardised training programme [Toothguide Training Box(®) (TTB)]. Each student then matched 30 randomly chosen shade tabs presented in an intra-oral setting by a standardised device [Toothguide Check Box(®) (TCB)]; 15 matches were made using the 3D and 15 using the LG shade guide system, under a daylight lamp (840 matches for each guide). It was recorded to what extent the presented and selected shade tabs, or the lightness group of the tabs, matched, also the needed time for colour matching. The results showed that 35% of perfect matches were observed for the 3D and 32% for the LG. The lightness group was correct in 59% of cases for 3D and 56% for LG. Mean time needed for matching of tabs and lightness group was no different between groups (no significant difference for any assessment). Within the limitations of the study design, the colour assessment with regard to performance and time needed in shade matching was not different with the LG or the 3D. Therefore, the user should choose which shade tab arrangement is more applicable. © 2010 Blackwell Publishing Ltd.

Cellular and humoral immune responses to a tetanus toxoid booster in perinatally HIV-1-infected children and adolescents receiving highly active antiretroviral therapy (HAART).

PubMed

Ching, Natascha; Deville, Jaime G; Nielsen, Karin A; Ank, Bonnie; Wei, Lian S; Sim, Myung Shin; Wolinsky, Steven M; Bryson, Yvonne J

2007-01-01

Human immunodeficiency virus type 1 (HIV-1) infected children treated with highly active antiretroviral therapy (HAART) may develop a significant reduction of plasma viremia associated with an increase in CD4+ T-cell counts. Functional capacity of this reconstituted immune system in response to recall antigens is important to maintain protective immunity to vaccine-preventable diseases. We therefore determined cellular and humoral immune responses to tetanus toxoid (TT) booster in perinatally HIV-1-infected children and adolescents receiving HAART. Immune responses were prospectively evaluated pre- and post-tetanus booster using lymphocyte proliferation assay (LPA) stimulation index (SI > or = 3.0) and tetanus antibody (TAb > or = 0.15) in 15 patients. The median interval from primary tetanus immunization series was 6 years (range 2-12 years). We compared patients by their virological response to HAART (complete responders, CR, n=7; incomplete responders, ICR, n=8). There were no significant differences in median age 12.6 years (CR: 12.9; ICR: 10.6) or median CD4 T-cell pre-booster (CR: 35%/819; ICR: 26%/429) between groups. Tetanus LPA responses were observed in one patient prior to booster and in seven patients post-booster. In contrast, 38% of patients had protective TAb pre-booster, but 92% developed protective TAb post-booster. All of the CR and 5/6 ICR patients developed protective TAb. HIV-1-infected children and adolescents had modest LPA responses to tetanus following booster, similar to HIV-1-infected adults. However, the majority of patients developed protective TAb levels after booster and maintained the response. Shorter intervals may need to be considered for TT immunization boosters in HIV-1-infected pediatric patients, as only 38% had protective TAb at baseline.

Simplified and refined structural modeling for economical flutter analysis and design

NASA Technical Reports Server (NTRS)

Ricketts, R. H.; Sobieszczanski, J.

1977-01-01

A coordinated use of two finite-element models of different levels of refinement is presented to reduce the computer cost of the repetitive flutter analysis commonly encountered in structural resizing to meet flutter requirements. One model, termed a refined model (RM), represents a high degree of detail needed for strength-sizing and flutter analysis of an airframe. The other model, called a simplified model (SM), has a relatively much smaller number of elements and degrees-of-freedom. A systematic method of deriving an SM from a given RM is described. The method consists of judgmental and numerical operations to make the stiffness and mass of the SM elements equivalent to the corresponding substructures of RM. The structural data are automatically transferred between the two models. The bulk of analysis is performed on the SM with periodical verifications carried out by analysis of the RM. In a numerical example of a supersonic cruise aircraft with an arrow wing, this approach permitted substantial savings in computer costs and acceleration of the job turn-around.

Rock surface roughness measurement using CSI technique and analysis of surface characterization by qualitative and quantitative results

NASA Astrophysics Data System (ADS)

Mukhtar, Husneni; Montgomery, Paul; Gianto; Susanto, K.

2016-01-01

In order to develop image processing that is widely used in geo-processing and analysis, we introduce an alternative technique for the characterization of rock samples. The technique that we have used for characterizing inhomogeneous surfaces is based on Coherence Scanning Interferometry (CSI). An optical probe is first used to scan over the depth of the surface roughness of the sample. Then, to analyse the measured fringe data, we use the Five Sample Adaptive method to obtain quantitative results of the surface shape. To analyse the surface roughness parameters, Hmm and Rq, a new window resizing analysis technique is employed. The results of the morphology and surface roughness analysis show micron and nano-scale information which is characteristic of each rock type and its history. These could be used for mineral identification and studies in rock movement on different surfaces. Image processing is thus used to define the physical parameters of the rock surface.

PlenoPatch: Patch-Based Plenoptic Image Manipulation.

PubMed

Zhang, Fang-Lue; Wang, Jue; Shechtman, Eli; Zhou, Zi-Ye; Shi, Jia-Xin; Hu, Shi-Min

2017-05-01

Patch-based image synthesis methods have been successfully applied for various editing tasks on still images, videos and stereo pairs. In this work we extend patch-based synthesis to plenoptic images captured by consumer-level lenselet-based devices for interactive, efficient light field editing. In our method the light field is represented as a set of images captured from different viewpoints. We decompose the central view into different depth layers, and present it to the user for specifying the editing goals. Given an editing task, our method performs patch-based image synthesis on all affected layers of the central view, and then propagates the edits to all other views. Interaction is done through a conventional 2D image editing user interface that is familiar to novice users. Our method correctly handles object boundary occlusion with semi-transparency, thus can generate more realistic results than previous methods. We demonstrate compelling results on a wide range of applications such as hole-filling, object reshuffling and resizing, changing object depth, light field upscaling and parallax magnification.

SPHERES tethered formation flight testbed: application to NASA's SPECS mission

NASA Astrophysics Data System (ADS)

Chung, Soon-Jo; Kong, Edmund M.; Miller, David W.

2005-08-01

This paper elaborates on theory and experiment of the formation flight control for the future space-borne tethered interferometers. The nonlinear equations of multi-vehicle tethered spacecraft system are derived by Lagrange equations and decoupling method. The preliminary analysis predicts unstable dynamics depending on the direction of the tether motor. The controllability analysis indicates that both array resizing and spin-up are fully controllable only by the reaction wheels and the tether motor, thereby eliminating the need for thrusters. Linear and nonlinear decentralized control techniques have been implemented into the tethered SPHERES testbed, and tested at the NASA MSFC's flat floor facility using two and three SPHERES configurations. The nonlinear control using feedback linearization technique performed successfully in both two SPHERES in-line configuration and three triangular configuration while varying the tether length. The relative metrology system, using the ultra sound metrology system and the inertial sensors as well as the decentralized nonlinear estimator, is developed to provide necessary state information.

Discrete Walsh Hadamard transform based visible watermarking technique for digital color images

NASA Astrophysics Data System (ADS)

Santhi, V.; Thangavelu, Arunkumar

2011-10-01

As the size of the Internet is growing enormously the illegal manipulation of digital multimedia data become very easy with the advancement in technology tools. In order to protect those multimedia data from unauthorized access the digital watermarking system is used. In this paper a new Discrete walsh Hadamard Transform based visible watermarking system is proposed. As the watermark is embedded in transform domain, the system is robust to many signal processing attacks. Moreover in this proposed method the watermark is embedded in tiling manner in all the range of frequencies to make it robust to compression and cropping attack. The robustness of the algorithm is tested against noise addition, cropping, compression, Histogram equalization and resizing attacks. The experimental results show that the algorithm is robust to common signal processing attacks and the observed peak signal to noise ratio (PSNR) of watermarked image is varying from 20 to 30 db depends on the size of the watermark.

Jet noise and performance comparison study of a Mach 2.55 supersonic cruise aircraft

NASA Technical Reports Server (NTRS)

Mascitti, V. R.; Maglieri, D. J.

1979-01-01

Data provided by the manufacturer relating to noise and performance of a Mach 2.55 supersonic cruise concept employing a post 1985 technology level, variable cycle engine was used to identify differences in noise levels and performance between the manfacturer and NASA associated with methodology and groundrules. In addition, economic and noise information is provided consistent with a previous study based on an advanced technology Mach 2.7 configuration. The results indicate that the difference between the NASA's and manfacturer's performance methodology is small. Resizing the aircraft to NASA groundrules also results in small changes in flyover, sideline and approach noise levels. For the power setting chosen, engine oversizing resulted in no reduction in traded noise. In terms of summated noise level, a 10 EPNdB reduction is realized for an 8 percent increase in total operating costs. This corresponds to an average noise reduction of 3.3 EPNdB at the three observer positions.

A semi-blind logo watermarking scheme for color images by comparison and modification of DFT coefficients

NASA Astrophysics Data System (ADS)

Kusyk, Janusz; Eskicioglu, Ahmet M.

2005-10-01

Digital watermarking is considered to be a major technology for the protection of multimedia data. Some of the important applications are broadcast monitoring, copyright protection, and access control. In this paper, we present a semi-blind watermarking scheme for embedding a logo in color images using the DFT domain. After computing the DFT of the luminance layer of the cover image, the magnitudes of DFT coefficients are compared, and modified. A given watermark is embedded in three frequency bands: Low, middle, and high. Our experiments show that the watermarks extracted from the lower frequencies have the best visual quality for low pass filtering, adding Gaussian noise, JPEG compression, resizing, rotation, and scaling, and the watermarks extracted from the higher frequencies have the best visual quality for cropping, intensity adjustment, histogram equalization, and gamma correction. Extractions from the fragmented and translated image are identical to extractions from the unattacked watermarked image. The collusion and rewatermarking attacks do not provide the hacker with useful tools.

76 FR 68521 - Self-Regulatory Organizations; NYSE Arca, Inc.; Order Granting Approval of Proposed Rule Change...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... Managed Fund Shares of TrimTabs Float Shrink ETF under NYSE Arca Equities Rule 8.600; Correction November... Rule Change to List and Trade Managed Fund Shares of TrimTabs Float Shrink ETF under NYSE Arca Equities...

Solar array construction

NASA Technical Reports Server (NTRS)

Crouthamel, Marvin S. (Inventor); Coyle, Peter J. (Inventor)

1982-01-01

An interconnect tab on each cell of a first set of circular solar cells connects that cell in series with an adjacent cell in the set. This set of cells is arranged in alternate columns and rows of an array and a second set of similar cells is arranged in the remaining alternate columns and rows of the array. Three interconnect tabs on each solar cell of the said second set are employed to connect the cells of the second set to one another, in series and to connect the cells of the second set to those of the first set in parallel. Some tabs (making parallel connections) connect the same surface regions of adjacent cells to one another and others (making series connections) connect a surface region of one cell to the opposite surface region of an adjacent cell; however, the tabs are so positioned that the array may be easily assembled by depositing the cells in a certain sequence and in proper orientation.

Effect of delta tabs on mixing and axis switching in jets from asymmetric nozzles

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

1994-01-01

The effect of delta tabs on mixing and the phenomenon of axis switching in free air jets from various asymmetric nozzles was studied experimentally. Flow visualization and Pitot probe surveys were carried out with a set of small nozzles (D = 1.47 cm) at a jet Mach number, Mj = 1.63. Hot wire measurements for streamwise vorticity were carried out with larger nozzles (D = 6.35 cm) at Mj = 0.31. Jet mixing with the asymmetric nozzles, as indicated by the mass fluxes downstream, was found to be higher than that produced by a circular nozzle. The circular nozzle with four delta tabs, however, produced fluxes much higher than that produced by a asymmetric nozzles themselves or by most of the tab configurations tried with them. Even higher fluxes could be obtained with only a few cases, e.g., with 3:1 rectangular nozzle with two large delta tabs placed on the narrow edges. In this case, the jet 'fanned out' at a large angle after going through one axis switch. The axis switching could be either stopped or augmented with suitable choice of the tab configurations. Two mechanisms are identified governing the phenomenon. One, as described in Ref. 12 and referred to here as the omega(sub Theta)-induced dynamics, is due to differential induced velocities of different segments of a rolled up azimuthal vortical structure. The other is the omega(sub x)-induced dynamics due to the induced velocities of streamwise vortex pairs in the flow. While the former dynamics are responsible for rapid axis switching in periodically forced jets, the effect of the tabs is governed mainly by the latter. It is inferred that both dynamics are active in a natural asymmetric jet issuing from a nozzle having an upstream contraction. The tendency for axis switching caused by the omega(sub Theta)-induced dynamics is resisted by the omega(sub x)-induced dynamics, leading to a delayed or no switch over in that case. In jets from orifices and in screeching jets, the omega(sub Theta)-induced dynamics dominate causing a faster switch over.

Traditional alcoholic beverages and their value in the local culture of the Alta Valle del Reno, a mountain borderland between Tuscany and Emilia-Romagna (Italy).

PubMed

Egea, Teresa; Signorini, Maria Adele; Ongaro, Luca; Rivera, Diego; Obón de Castro, Concepción; Bruschi, Piero

2016-06-22

Traditional alcoholic beverages (TABs) have only received marginal attention from researchers and ethnobotanists so far, especially in Italy. This work is focused on plant-based TABs in the Alta Valle del Reno, a mountainous area on the border between Tuscany and Emilia-Romagna regions. The aims of our study were to document local knowledge about TABs and to analyze and discuss the distribution of related knowledge within the investigated communities. Field data were collected through semi-structured interviews. The relative importance of each plant species used to prepare TABs was assessed by calculating a general Use Value Index (UV general), a current UV (UV current) and a past UV (UV past). We also assessed personal experience of use by calculating effective and potential UV (UV effective, UV potential). A multivariate analysis was performed to compare ingredients in recipes recorded in the Alta Valle del Reno with those reported for neighboring areas. Forty-six plant species, belonging to 20 families, were recorded. Rosaceae was the most significant family (98 citations, 19 species), followed by Rutaceae (15, 3) and Lamiaceae (12, 4). The most important species was Prunus cerasus L. (UV general = 0.44), followed by Juglans regia L. (0.38), Rubus idaeus L. (0.27) and Prunus spinosa L. (0.22). Species with the highest UV current were Juglans regia (0.254), Prunus cerasus (0.238) and Citrus limon L. (0.159). The highest UV effective values were obtained by Prunus cerasus (0.413), Juglans regia (0.254), Rubus idaeus (0.222) and Citrus limon (0.206). We also discuss the results of the multivariate analysis. TABs proved to occupy an important place in the traditional culture and social life of the studied communities. Moreover, data highlight the local specificity and richness of this kind of tradition in the Alta Valle del Reno, compared to other Italian areas. Some plant ingredients used for TABs have potential nutraceutical and even therapeutic properties that are well known by local people. These properties could constitute an additional economic value for TABs' commercialization, which in turn could promote the local rural economy.

Evaluation of Insomrid Tablet and Shirodhara in the management of Anidra (Insomnia).

PubMed

Pokharel, Sanjay; Sharma, Ajay Kumar

2010-01-01

The study was conducted in 30 clinically diagnosed patients of Anidra (Insomnia) with an objective of clinical evaluation of the efficacy of Shirodhara and Tab. Insomrid (proposed herbal formulation) in the management of Anidra (Insomnia). These patients were randomly divided into three groups of 10 patients each. In was observed that the patients of Group III treated with Tab. Insomrid and Shirodhara with milk showed highly significant improvements, whereas the Group II treated with Shirodhara and Group I treated with Tab. Insomrid also showed significant improvements. No adverse effects were noted in any of the patients during the trial period.

Evaluation of Insomrid Tablet and Shirodhara in the management of Anidra (Insomnia)

PubMed Central

Pokharel, Sanjay; Sharma, Ajay Kumar

2010-01-01

The study was conducted in 30 clinically diagnosed patients of Anidra (Insomnia) with an objective of clinical evaluation of the efficacy of Shirodhara and Tab. Insomrid (proposed herbal formulation) in the management of Anidra (Insomnia). These patients were randomly divided into three groups of 10 patients each. In was observed that the patients of Group III treated with Tab. Insomrid and Shirodhara with milk showed highly significant improvements, whereas the Group II treated with Shirodhara and Group I treated with Tab. Insomrid also showed significant improvements. No adverse effects were noted in any of the patients during the trial period. PMID:22131683

14 CFR 25.677 - Trim systems.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.677 Trim systems. (a) Trim controls must be designed to prevent inadvertent or abrupt operation and to operate in the plane... designed to prevent creeping in flight. Trim tab controls must be irreversible unless the tab is...

14 CFR 25.677 - Trim systems.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.677 Trim systems. (a) Trim controls must be designed to prevent inadvertent or abrupt operation and to operate in the plane... designed to prevent creeping in flight. Trim tab controls must be irreversible unless the tab is...

14 CFR 25.677 - Trim systems.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.677 Trim systems. (a) Trim controls must be designed to prevent inadvertent or abrupt operation and to operate in the plane... designed to prevent creeping in flight. Trim tab controls must be irreversible unless the tab is...

14 CFR 25.677 - Trim systems.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.677 Trim systems. (a) Trim controls must be designed to prevent inadvertent or abrupt operation and to operate in the plane... designed to prevent creeping in flight. Trim tab controls must be irreversible unless the tab is...

Sildenafil ameliorates left ventricular T-tubule remodeling in a pressure overload-induced murine heart failure model

PubMed Central

Huang, Chun-kai; Chen, Bi-yi; Guo, Ang; Chen, Rong; Zhu, Yan-qi; Kutschke, William; Hong, Jiang; Song, Long-sheng

2016-01-01

Aim: Sildenafil, a phosphodiesterase 5 (PDE5) inhibitor, has been shown to exert beneficial effects in heart failure. The purpose of this study was to test whether sildenafil suppressed transverse-tubule (T-tubule) remodeling in left ventricular (LV) failure and thereby providing the therapeutic benefits. Methods: A pressure overload-induced murine heart failure model was established in mice by thoracic aortic banding (TAB). One day after TAB, the mice received sildenafil (100 mg·kg−1·d−1, sc) or saline for 5 weeks. At the end of treatment, echocardiography was used to examine LV function. Then the intact hearts were dissected out and placed in Langendorff-perfusion chamber for in situ confocal imaging of T-tubule ultrastructure from epicardial myocytes. Results: TAB surgery resulted in heart failure accompanied by remarkable T-tubule remodeling. Sildenafil treatment significantly attenuated TAB-induced cardiac hypertrophy and congestive heart failure, improved LV contractile function, and preserved T-tubule integrity in LV cardiomyocytes. But sildenafil treatment did not significantly affect the chamber dilation. The integrity of LV T-tubule structure was correlated with cardiac hypertrophy (R2=0.74, P<0.01) and global LV function (R2=0.47, P<0.01). Conclusion: Sildenafil effectively ameliorates LV T-tubule remodeling in TAB mice, revealing a novel mechanism underlying the therapeutic benefits of sildenafil in heart failure. PMID:26972492

Effects of a shade-matching light and background color on reliability in tooth shade selection.

PubMed

Najafi-Abrandabadi, Siamak; Vahidi, Farhad; Janal, Malvin N

2018-01-01

The purpose of this study was to evaluate the effects of a shade-matching light (Rite-Lite-2, AdDent) and different viewing backgrounds on reliability in a test of shade tab matching. Four members of the Prosthodontic faculty matched 10 shade tabs selected for a range of shades against the shade guide. All raters were tested for color blindness and were calibrated prior to the study. Matching took place under four combinations of conditions: with operatory light or the shade-matching light, and using either a pink or a blue background. Reliability was quantified with the kappa statistic, separately for agreement of value, hue, and chroma for each shade tab. In general, raters showed fair to moderate levels of agreement when judging the value of the shade tabs, but could not agree on the hue and chroma of the stimuli. The pink background led to higher levels of agreement than the blue background, and the shade-matching light improved agreement when used in conjunction with the pink but not the blue background. Moderate levels of agreement were found in matching shade tab value. Agreement was generally better when using the pink rather than the blue background, regardless of light source. The use of the shade-matching light tended to amplify the advantage of the pink background.

Microbiological examination of vegetable seed sprouts in Korea.

PubMed

Kim, Hoikyung; Lee, Youngjun; Beuchat, Larry R; Yoon, Bong-June; Ryu, Jee-Hoon

2009-04-01

Sprouted vegetable seeds used as food have been implicated as sources of outbreaks of Salmonella and Escherichia coli O157:H7 infections. We profiled the microbiological quality of sprouts and seeds sold at retail shops in Seoul, Korea. Ninety samples of radish sprouts and mixed sprouts purchased at department stores, supermarkets, and traditional markets and 96 samples of radish, alfalfa, and turnip seeds purchased from online stores were analyzed to determine the number of total aerobic bacteria (TAB) and molds or yeasts (MY) and the incidence of Salmonella, E. coli O157:H7, and Enterobacter sakazakii. Significantly higher numbers of TAB (7.52 log CFU/g) and MY (7.36 log CFU/g) were present on mixed sprouts than on radish sprouts (6.97 and 6.50 CFU/g, respectively). Populations of TAB and MY on the sprouts were not significantly affected by location of purchase. Radish seeds contained TAB and MY populations of 4.08 and 2.42 log CFU/g, respectively, whereas populations of TAB were only 2.54 to 2.84 log CFU/g and populations of MY were 0.82 to 1.69 log CFU/g on alfalfa and turnip seeds, respectively. Salmonella and E. coli O157:H7 were not detected on any of the sprout and seed samples tested. E. sakazakii was not found on seeds, but 13.3% of the mixed sprout samples contained this potentially pathogenic bacterium.

Impact of phlebotomine sand flies on U.S. Military operations at Tallil Air Base, Iraq: 1. background, military situation, and development of a "Leishmaniasis Control Program".

PubMed

Coleman, Russell E; Burkett, Douglas A; Putnam, John L; Sherwood, Van; Caci, Jennifer B; Jennings, Barton T; Hochberg, Lisa P; Spradling, Sharon L; Rowton, Edgar D; Blount, Keith; Ploch, John; Hopkins, Grady; Raymond, Jo-Lynne W; O'Guinn, Monica L; Lee, John S; Weina, Peter J

2006-07-01

One of the most significant modern day efforts to prevent and control an arthropod-borne disease during a military deployment occurred when a team of U.S. military entomologists led efforts to characterize, prevent, and control leishmaniasis at Tallil Air Base (TAB), Iraq, during Operation Iraqi Freedom. Soon after arriving at TAB on 22 March 2003, military entomologists determined that 1) high numbers of sand flies were present at TAB, 2) individual soldiers were receiving many sand fly bites in a single night, and 3) Leishmania parasites were present in 1.5% of the female sand flies as determined using a real-time (fluorogenic) Leishmania-generic polymerase chain reaction assay. The rapid determination that leishmaniasis was a specific threat in this area allowed for the establishment of a comprehensive Leishmaniasis Control Program (LCP) over 5 mo before the first case of leishmaniasis was confirmed in a U.S. soldier deployed to Iraq. The LCP had four components: 1) risk assessment, 2) enhancement of use of personal protective measures by all personnel at TAB, 3) vector and reservoir control, and 4) education of military personnel about sand flies and leishmaniasis. The establishment of the LCP at TAB before the onset of any human disease conclusively demonstrated that entomologists can play a critical role during military deployments.

Unitized Nut-and-Washer Assembly

NASA Technical Reports Server (NTRS)

Rossi, P. J.

1986-01-01

Combination nut, washer, and lockwasher secures parts quickly without damaging metal finishes. Nut and lockwasher are captured by bent tabs of flat washer in this concept for unified fastener. Optional perforated tab on flat washer allows easy tagging and storage. Fastener intended for attaching leads and buses to studs on electronic equipment.

Heat Lamps Solder Solar Array Quickly

NASA Technical Reports Server (NTRS)

Coyle, P. J.; Crouthamel, M. S.

1982-01-01

Interconnection tabs in a nine-solar-cell array have been soldered simultaneously with radiant heat. Cells and tabs are held in position for soldering by sandwiching them between compliant silicone-rubber vacuum platen and transparent polyimide sealing membrane. Heat lamps warm cells, producing smooth, flat solder joints of high quality.

Exploring Differences in Practicing Teachers' Valuing of Pedagogical Knowledge Based on Teaching Ability Beliefs

ERIC Educational Resources Information Center

Fives, Helenrose; Buehl, Michelle M.

2014-01-01

In this investigation, we assessed 443 teachers' beliefs with the "Teaching Ability Belief Scale" (TABS) and the "Importance of Teaching Knowledge Scale" (ITKS). Using cluster analysis, we identified four groups of teachers based on their responses to the TABS reflecting "Innate," "Learned,"…

1984 TABS Final Report.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

This report presents Austin Independent School District 1984 test results on the Texas Assessment of Basics Skills (TABS). It was administered to all third, fifth and ninth grade students and to high school students not meeting ninth grade state-set mastery criteria, the minimum competency requirement for graduation. Results are presented as…

Solar cell submodule design facilitates assembly of lightweight arrays

NASA Technical Reports Server (NTRS)

Yasui, R. K.

1966-01-01

Solar cell submodules with bus bars that leave tabs along one end of the submodule and wires with raised portions along the other end are assembled by interlocking the tabs and wires of adjacent submodules. This structural design is lightweight and reliable and requires no metallic substructure.

Standardizng Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Nathan A.; Klemm, Juli; Harper, Stacey

2013-02-05

To enable the rational design of nanomaterials for improved efficacy and safety, it is critical to understand and exploit the physicochemical properties that drive biological behavior (Morris, 2010). Data mining and computer simulation are essential for deriving information about nanomaterial behavior; however, the datasets needed to support such studies are sparse and stored across a variety of repositories and resources. Schrurs and Lison (2012) have expressed the need for more coherence and structure in the conduct of nanotechnology research. Additionally, the lack of common reporting standards and non-uniformity of information reported have proven to be significant barriers to such datamore » sharing and re-use. The Nanotechnology Working Group (Nano WG), of the US National Institutes of Health National Cancer Informatics Program, has been focused on addressing these barriers. The Nano WG - which includes representatives from over 20 organizations including government agencies, academia, industry, standards organizations, and alliances -has developed ISA-TAB-Nano (Thomas et al, 2013), a general framework for representing and integrating diverse types of data related to the description and characterization of nanomaterials. Recognizing that nanoparticle characterization studies have many of the same challenges as ‘omics-based assays, the Nano WG joined the ISA Commons (Sansone et al., 2012) to leverage lessons learned in ‘omics data sharing. The ISA Commons community brings together 50 collaborators at over 30 scientific organizations around the globe, including regulatory and industrial participants in an increasingly diverse set of life science domains. At the core of the ISA Commons is the ISA metadata tracking framework which forms the basis for the ISA-TAB-Nano extension. The extension of the ISA framework to nanotechnology domain illustrates the power of a synergistic approach that seeks the interoperability of data across multiple research disciplines. To increase adoption, especially in the commercial arena from vendors and manufactures, the ISA-Tab-Nano data-sharing specification has also been submitted for consideration as a standard to the American Society for Testing and Materials (ASTM). Delivering a community-driven specification is only the first phase of the process. To be useful and used, ISA-TAB-Nano must be implemented by tools and databases to assist researchers in reporting their data accordingly, shielding them from unnecessary complexity. Our next step is to extend the open source ISA Software Suite to provide user-oriented tools for the collection, curation, and storage of data compliant with the ISA-TAB-Nano specification. Future work will also focus on the application of the ISA-TAB-Nano format to support emerging standards on minimal information about nanomaterials in biological research (Ostraat et al, 2012; MinChar). ISA-TAB-Nano development is a community-driven effort and we welcome new contributions, collaborations and domain expertise. We invite researchers, software developers, vendors, and other stakeholders to work with us to implement the ISA-Tab-Nano format in their existing systems and research. Likewise, we welcome engagement of regulators, funding agencies, editors, and other policy makers to discuss how this standard can be used to facilitate the sharing and reuse of nanotechnology data across a wide range of disciplines. More information about the ISA-TAB-Nano project can be found online at https://wiki.nci.nih.gov/display/ICR/ISA-TAB-Nano.« less

Influence of the axial rotation angle on tool mark striations.

PubMed

Garcia, Derrel Louis; Pieterman, René; Baiker, Martin

2017-10-01

A tool's axial rotation influences the geometric properties of a tool mark. The larger the axial rotation angle, the larger the compression of structural details like striations. This complicates comparing tool marks at different axial rotations. Using chisels, tool marks were made from 0° to 75° axial rotation and compared using an automated approach Baiker et al. [10]. In addition, a 3D topographic surface of a chisel was obtained to generate virtual tool marks and to test whether the axial rotation angle of a mark could be predicted. After examination of the tool mark and chisel data-sets it was observed that marks lose information with increasing rotation due to the change in relative distance between geometrical details on the tool and the disappearance of smaller details. The similarity and repeatability were high for comparisons between marks with no difference in axial rotation, but decreasing with increased rotation angle from 0° to 75°. With an increasing difference in the rotation angles, the tool marks had to be corrected to account for the different compression factors between them. For compression up to 7.5%, this was obtained automatically by the tool mark alignment method. For larger compression, manually re-sizing the marks to the uncompressed widths at 0° rotation before the alignment was found suitable for successfully comparing even large differences in axial rotation. The similarity and repeatability were decreasing however, with increasing degree of re-sizing. The quality was assessed by determining the similarity at different detail levels within a tool mark. With an axial rotation up to 75°, tool marks were found to reliably represent structural details down to 100μm. The similarity of structural details below 100μm was dependent on the angle, with the highest similarity at small rotation angles and the lowest similarity at large rotation angles. Filtering to remove the details below 100μm lead to consistently higher similarity between tool marks at all angles and allowed for a comparison of marks up to 75° axial rotation. Finally, generated virtual tool mark profiles with an axial rotation were compared to experimental tool marks. The similarity between virtual and experimental tool marks remained high up to 60° rotation after which it decreased due to the loss in quality in both marks. Predicting the rotation angle is possible under certain conditions up to 45° rotation with an accuracy of 2.667±0.577° rotation. Copyright © 2017 Elsevier B.V. All rights reserved.

A versatile data-visualization application for the Norwegian flood forecasting service

NASA Astrophysics Data System (ADS)

Kobierska, Florian; Langsholt, Elin G.; Hamududu, Byman H.; Engeland, Kolbjørn

2017-04-01

- General motivation A graphical user interface has been developed to visualize multi-model hydrological forecasts at the flood forecasting service of the Norwegian water and energy directorate. It is based on the R 'shiny' package, with which interactive web applications can quickly be prototyped. The app queries multiple data sources, building a comprehensive infographics dashboard for the decision maker. - Main features of the app The visualization application comprises several tabs, each built with different functionality and focus. A map of forecast stations gives a rapid insight of the flood situation and serves, concurrently, as a map station selection (based on the 'leaflet' package). The map selection is linked to multi-panel forecast plots which can present input, state or runoff parameters. Another tab focuses on past model performance and calibration runs. - Software design choices The application was programmed with a focus on flexibility regarding data-sources. The parsing of text-based model results was explicitly separated from the app (in the separate R package 'NVEDATA'), so that it only loads standardized RData binary files. We focused on allowing re-usability in other contexts by structuring the app into specific 'shiny' modules. The code was bundled into an R package, which is available on GitHub. - Documentation efforts A documentation website is under development. For easier collaboration, we chose to host it on the 'GitHub Pages' branch of the repository and build it automatically with a continuous integration service. The aim is to gather all information about the flood forecasting methodology at NVE in one location. This encompasses details on each hydrological model used as well as the documentation of the data-visualization application. - Outlook for further development The ability to select a group of stations by filtering a table (i.e. past performance, past major flood events, catchment parameters) and exporting it to the forecast tab could be of interest for detailed model analysis. The design choices for this app were motivated by a need for extensibility and modularity and those qualities will be tested and improved as new datasets need integrating into this to​ol.

32 CFR 770.8 - Reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... killing a deer or turkey, a hunter must attach the appropriate tab from his big game license to the carcass before moving the game from the place of kill. The game will then be taken to the Game Checking Station where the tab will be exchanged for an official game tag. All other game, not requiring a tag...

32 CFR 770.8 - Reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... killing a deer or turkey, a hunter must attach the appropriate tab from his big game license to the carcass before moving the game from the place of kill. The game will then be taken to the Game Checking Station where the tab will be exchanged for an official game tag. All other game, not requiring a tag...

32 CFR 770.8 - Reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... killing a deer or turkey, a hunter must attach the appropriate tab from his big game license to the carcass before moving the game from the place of kill. The game will then be taken to the Game Checking Station where the tab will be exchanged for an official game tag. All other game, not requiring a tag...

32 CFR 770.8 - Reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... killing a deer or turkey, a hunter must attach the appropriate tab from his big game license to the carcass before moving the game from the place of kill. The game will then be taken to the Game Checking Station where the tab will be exchanged for an official game tag. All other game, not requiring a tag...

32 CFR 770.8 - Reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... killing a deer or turkey, a hunter must attach the appropriate tab from his big game license to the carcass before moving the game from the place of kill. The game will then be taken to the Game Checking Station where the tab will be exchanged for an official game tag. All other game, not requiring a tag...

The Comparison of the Inquiry Behavior of ISCS and Non-ISCS Science Students as Measured by the Tab Science Test

ERIC Educational Resources Information Center

Stallings, Everett S.; Snyder, William R.

1977-01-01

Studies of a group of seventh-grade students who were tested for inquiry skills using the TAB Science Test showed no significant differences between those students who had studied the Intermediate Science Curriculum Study (ISCS) and those who studied another curriculum. (MLH)

Rearview Mirror Dimming Function

ERIC Educational Resources Information Center

Layton, William

2011-01-01

Students are often unaware of the little tab on a rear-view mirror that is used to dim headlights from the rear. Those who know about this tab are usually interested in knowing how it works. Explanations of the optics involved can be found in Serway and Jewett and Jones and Edge. An alternate explanation is given.

Formed photovoltaic module busbars

DOEpatents

Rose, Douglas; Daroczi, Shan; Phu, Thomas

2015-11-10

A cell connection piece for a photovoltaic module is disclosed herein. The cell connection piece includes an interconnect bus, a plurality of bus tabs unitarily formed with the interconnect bus, and a terminal bus coupled with the interconnect bus. The plurality of bus tabs extend from the interconnect bus. The terminal bus includes a non-linear portion.

Engaging Learners through Artmaking: Choice-Based Art Education in the Classroom (TAB). Second Edition

ERIC Educational Resources Information Center

Douglas, Katherine M.; Jaquith, Diane B.

2018-01-01

The authors who introduced the concepts of Teaching for Artistic Behavior (TAB) and choice-based art education have completely revised and updated their original, groundbreaking bestseller that was designed to facilitate independent learning and support student choices in subject matter and media. More than ever before, teachers are held…

Ergonomics Designs of Aluminum Beverage Cans & Bottles

NASA Astrophysics Data System (ADS)

Han, Jing; Itoh, Ryouiti; Yamazaki, Koetsu; Nishiyama, Sadao; Shinguryo, Takuro

2005-08-01

This paper introduced the finite element analyses into the ergonomics designs to evaluate the human feelings numerically and objectively. Two design examples in developing aluminum beverage cans & bottles are presented. The first example describes a design of the tab of the can with better finger access. A simulation of finger pulling up the tab of the can has been performed and a pain in the finger has been evaluated by using the maximum value of the contact stress of a finger model. The finger access comparison of three kinds of tab ring shape designs showed that the finger access of the tab that may have a larger contact area with finger is better. The second example describes a design of rib-shape embossed bottles for hot vending. Analyses of tactile sensation of heat have been performed and the amount of heat transmitted from hot bottles to finger was used to present the hot touch feeling. Comparison results showed that the hot touch feeling of rib-shape embossed bottles is better than that of cylindrical bottles, and that the shape of the rib also influenced the hot touch feeling.

Analytic investigation of helicopter rotor blade appended aeroelastic devices

NASA Technical Reports Server (NTRS)

Bielawa, Richard L.

1984-01-01

Analytic evaluations of four different passive aeroelastic devices appended to helicopter rotor blades are presented. The devices consist of a passive tuned tab, a control coupled tab, an all-flying tip and a harmonic dilational airfoil tip. Each device was conceived for improving either aerodynamic performance or reducing vibratory control loads or hub shears. The evaluation was performed using a comprehensive rotor aeroelastic analysis (the G400PA code with appropriate modifications), together with data for a realistic helicopter rotor blade (the UH-60A Blackhawk), in high speed flight (90 m/s, 175 kts). The results of this study show that significant performance (L/(D sub e)) gains can be achieved with the all-flying free tip. Results from the harmonic dilational airfoil tip show the potential for moderate improvements in L/(D sub e). Finally, the results for the passive tuned tab and the control coupled tab, as configured for this study, show these devices to be impractical. Sections are included which describe the operation of each device, the required G400PA modifications, and the detailed results obtained for each device.

Method and apparatus for adding electrolyte to a fuel cell stack

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.V.; English, J.G.

1986-06-24

A process is described for adding electrolyte to a fuel cell stack, the stack comprising sheet-like elements defining a plurality of fuel cell units disposed one atop the other in abutting relationship, the units defining a substantially flat, vertically extending face, each unit including a cell comprising a pair of sheet-like spaced apart gas porous electrodes with a porous matrix layer sandwiched therebetween for retaining electrolyte during cell operation, each unit also including a sheet-like substantially non-porous separator, the separator being sandwiched between the cells of adjacent units. The improvement described here consists of: extending at least one of themore » sheet-like elements of each of a plurality of the fuel cell units outwardly from the stack face to define horizontal tabs disposed one above the other; depositing dilute electrolyte directly from electrolyte supply means upon substantially the full length, parallel to the stack face, of at least the uppermost tab, the tabs being constructed and arranged such that at least a portion of the deposited electrolyte cascades from tab to tab and down the face of the stack, the deposited electrolyte being absorbed by capillary action into the elements of the stack, the step of depositing continuing until all of the electrodes and matrix layers of the stack are fully saturated with the dilute electrolyte; and thereafter evaporating liquid from the saturated elements under controlled conditions of humidity and temperature until the stack has a desired electrolyte volume and electrolyte concentration therein.« less

Comparison of properties of tablets and energy profile of compaction of two spray-dried lactoses.

PubMed

Muzíková, Jitka; Sináglová, Pavla

2013-01-01

The paper compared two spray-dried lactoses Flowlac 100 and SuperTab 14SD from the standpoint of tensile strength and disintegration time of tablets, the effect of an addition of the lubricant magnesium stearate and silicified microcrystalline cellulose on these properties, and also from the standpoint of the energy profile of compression. The comparison of the values was performed at the compression force of 15 kN. The strength of tablets was higher in the case of SuperTab 14SD, an increase in the concentration of magnesium stearate did not decrease tablet strength. Prosolv SMCC 90 increased the strength of tablets and made it equal for both lactoses, but it also increased the sensitivity to the added lubricant. The disintegration time of tablets was shorter in the case of SuperTab 14SD, an increased concentration of magnesium stearate prolonged it, and an addition of Prosolv SMCC 90 shortened it and made it equal for both lactoses. From the energy standpoint, the maximal energy was higher in the case of SuperTab 14SD, an addition of Prosolv SMCC 90 increased it and again made it equal for both lactoses. The differences in the values of the maximal energy were primarily due to the values of the energy for friction and the energy accumulated by the tablet after compression, and there was no marked difference in the values of the energy of decompression. SuperTab 14SD showed a higher plasticity than Flowlac 100.

Direct and conceptual replications of the taxometric analysis of type a behavior.

PubMed

Wilmot, Michael P; Haslam, Nick; Tian, Jingyuan; Ones, Deniz S

2018-05-17

We present direct and conceptual replications of the influential taxometric analysis of Type A Behavior (TAB; Strube, 1989), which reported evidence for the latent typology of the construct. Study 1, the direct replication (N = 2,373), duplicated sampling and methodological procedures of the original study, but results showed that the item indicators used in the original study lacked sufficient validity to unambiguously determine latent structure. Using improved factorial subscale indicators to further test the question, multiple taxometric procedures, in combination with parallel analyses of simulated data, failed to replicate the original typological finding. Study 2, the conceptual replication, tested the latent structure of the wider construct of TAB using the sample from the Caerphilly Prospective Study (N = 2,254), which contains responses to the three most widely used self-report measures of TAB: the Jenkins Activity Survey, Bortner scale, and Framingham scale. Factorial subscale indicators were derived from the measures and submitted to multiple taxometric procedures. Results of Study 2 converged with those of Study 1, providing clear evidence of latent dimensional structure. Overall, results suggest there is no evidence for the type in TAB. Findings imply that theoretical models of TAB, assessment practices, and data analytic procedures that assume a typology should be replaced by dimensional models, factorial subscale measures, and corresponding statistical approaches. Specific subscale measures that tap multiple Big Five trait domains, and show evidence of predictive utility, are also recommended. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

The effect of various disinfectants on dental shade guides.

PubMed

Huang, Peterson Y; Masri, Radi; Romberg, Elaine; Driscoll, Carl F

2014-09-01

Dental shade guides are used to evaluate tooth color before prosthodontic procedures and are subjected to disinfection after use. The effect of disinfection on shade guides has not been thoroughly investigated. The purpose of this study was to evaluate the effect of disinfectants on the color of shade tabs. Changes in the color (ΔE) of VITA Classical Shade Guide tabs were measured with a VITA Easyshade spectrophotometer in the CIELAB system and calculated after being subjected to Cavicide, Asepticare TB, Sporicidin, and distilled water (control) over a simulated period of 2 years. Statistical analysis was accomplished by a 2-way analysis of variance followed by the Tukey honestly significant difference (HSD) test (α=.05). A significant difference was noted in the degree of shade tab color change, depending on the type of disinfectant used (F=153.2, P<.001). No significant difference was noted in the amount of shade tab color change that occurred after disinfection among the different shade tabs used (F=0.611, P=.865), nor was a significant interaction noted between the type of disinfectant and the different shade tabs used (F=0.7, P=.919). Asepticare TB showed the least significant amount of change (ΔE=0.401), and Sporicidin (ΔE=0.889) and the control (ΔE=0.969) showed significantly more color change than Asepticare TB but less than Cavicide (ΔE=1.198). The average total CIELAB color difference for 50% human perceptibility is approximately 1 unit (under standardized laboratory conditions). In the oral cavity, however, an average change of 3.7 ΔE units could still allow teeth to be perceived as having the same color. Therefore, although the results are statistically significant, they may not be clinically important. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

The relationship between clinical characteristics, radiographic osteoarthritis and 3D bone area: data from the osteoarthritis initiative.

PubMed

Barr, A J; Dube, B; Hensor, E M A; Kingsbury, S R; Peat, G; Bowes, M A; Conaghan, P G

2014-10-01

Radiographic measures of osteoarthritis (OA) are based upon two dimensional projection images. Active appearance modelling (AAM) of knee magnetic resonance imaging (MRI) enables accurate, 3D quantification of joint structures in large cohorts. This cross-sectional study explored the relationship between clinical characteristics, radiographic measures of OA and 3D bone area (tAB). Clinical data and baseline paired radiographic and MRI data, from the medial compartment of one knee of 2588 participants were obtained from the NIH Osteoarthritis Initiative (OAI). The medial femur (MF) and tibia (MT) tAB were calculated using AAM. 'OA-attributable' tAB (OA-tAB) was calculated using data from regression models of tAB of knees without OA. Associations between OA-tAB and radiographic measures of OA were investigated using linear regression. In univariable analyses, height, weight, and age in female knees without OA explained 43.1%, 32.1% and 0.1% of the MF tAB variance individually and 54.4% when included simultaneously in a multivariable model. Joint space width (JSW), osteophytes and sclerosis explained just 5.3%, 14.9% and 10.1% of the variance of MF OA-tAB individually and 17.4% when combined. Kellgren Lawrence (KL) grade explained approximately 20% of MF OA-tAB individually. Similar results were seen for MT OA-tAB. Height explained the majority of variance in tAB, confirming an allometric relationship between body and joint size. Radiographic measures of OA, derived from a single radiographic projection, accounted for only a small amount of variation in 3D knee OA-tAB. The additional structural information provided by 3D bone area may explain the lack of a substantive relationship with these radiographic OA measures. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Cardiovascular and Metabolic Demads of the Kettlebell Swing using Tabata Interval versus a Traditional Resistance Protocol

PubMed Central

FORTNER, HOWARD A.; SALGADO, JEANETTE M.; HOLMSTRUP, ANGELICA M.; HOLMSTRUP, MICHAEL E.

2014-01-01

Tabata (TAB) training, consisting of eight cycles of 20 seconds of maximal exercise followed by 10 seconds of rest, is time-efficient, with aerobic and anaerobic benefit. This study investigated the cardiovascular and metabolic demands of a TAB versus traditional (TRAD) resistance protocol with the kettlebell swing. Fourteen young (18–25y), non-obese (BMI 25.7±0.8 kg/m2) participants reported on three occasions. All testing incorporated measurements of HR, oxygen consumption, and blood lactate accumulation. Each participant completed Tabata kettlebell swings (male- 8kg, female- 4.5kg; 8 intervals; 20s maximal repetitions, 10s rest). On a subsequent visit (TRAD), the total swings from the TAB protocol were evenly divided into 4 sets, with 90s rest between sets. Outcome measures were compared using paired t-tests. The TAB was completed more quickly than the TRAD protocol (240.0±0.0 v. 521.5±3.3 sec, P<0.01), at a higher perceived exertion (Borg RPE; 15.1±0.7 v. 11.7±0.9, P<0.01). The TAB elicited a higher average VO2 value (33.1±1.5 v. 27.2±1.6 ml/kg/min, P<0.01), percent of VO2peak achieved (71.0±0.3 v. 58.4±0.3%, P<0.01), maximal HR (162.4±4.6 v. 145.6±4.8 bpm, P<0.01), and post-exercise blood lactate concentration (6.4±1.1 v. 3.7±0.5 mmol/L, P<0.01). Conclusion The kettlebell swing demonstrated significantly greater cardiovascular and metabolic responses within a TAB vs. TRAD framework. Appropriate screening and risk stratification are advised before implementing kettlebell swings. PMID:27182402

Prehospital high-dose sublingual nitroglycerin rarely causes hypotension.

PubMed

Clemency, Brian M; Thompson, Jeffrey J; Tundo, Gina N; Lindstrom, Heather A

2013-10-01

High-dose intravenous nitroglycerin is a common in-hospital treatment for respiratory distress due to congestive heart failure (CHF) with hypertension. Intravenous (IV) nitroglycerin administration is impractical in the prehospital setting. In 2011, a new regional Emergency Medical Services (EMS) protocol was introduced allowing advanced providers to treat CHF with high-dose oral nitroglycerin. The protocol calls for patients to be treated with two sublingual tabs (0.8 mg) when systolic blood pressure (SBP) was >160 mm Hg, or three sublingual tabs (1.2 mg) when SBP was >200 mm Hg, every five minutes as needed. Hypothesis/Problem To assess the protocol's safety, the incidence of hypotension following prehospital administration of multiple simultaneous nitroglycerin (MSN) tabs by EMS providers was studied. This study was a retrospective cohort study of patients from a single commercial EMS agency over a 6-month period. Records from patients with at least one administration of MSN were reviewed. For each administration, the first documented vital signs pre- and post-administration were compared. Administrations were excluded if pre- or post-administration vital signs were missing. One hundred case-patients had at least one MSN administration by an advanced provider during the study period. Twenty-five case-patients were excluded due to incomplete vital signs. Seventy-five case-patients with 95 individual MSN administrations were included for analysis. There were 65 administrations of two tabs, 29 administrations of three tabs, and one administration of four tabs. The mean change in SBP following MSN was -14.7 mm Hg (SD = 30.7; range, +59 to -132). Three administrations had documented systolic hypotension in the post-administration vital signs (97/71, 78/50 and 66/47). All three patients were over 65 years old, were administered two tabs, had documented improved respiratory status, and had repeat SBP of at least 100. The incidence of hypotension following MSN administration was 3.2%. Discussion High-dose oral nitroglycerin administration is a practical alternative to IV nitroglycerin in the prehospital setting when administered by advanced providers. The prehospital protocol for high dose oral nitroglycerin was demonstrated to be safe in the cohort of patients studied. Limitations of the study include the relatively small sample size and the inability to identify hypotension that may have occurred following the cessation of data collection in the field. Hypotension was rare and self-limited in prehospital patients receiving MSN.

A multifunctional role of trialkylbenzenes for the preparation of aqueous colloidal mesostructured/mesoporous silica nanoparticles with controlled pore size, particle diameter, and morphology

NASA Astrophysics Data System (ADS)

Yamada, Hironori; Ujiie, Hiroto; Urata, Chihiro; Yamamoto, Eisuke; Yamauchi, Yusuke; Kuroda, Kazuyuki

2015-11-01

Both the pore size and particle diameter of aqueous colloidal mesostructured/mesoporous silica nanoparticles (CMSS/CMPS) derived from tetrapropoxysilane were effectively and easily controlled by the addition of trialkylbenzenes (TAB). Aqueous highly dispersed CMPS with large pores were successfully obtained through removal of surfactants and TAB by a dialysis process. The pore size (from 4 nm to 8 nm) and particle diameter (from 50 nm to 380 nm) were more effectively enlarged by the addition of 1,3,5-triisopropylbenzene (TIPB) than 1,3,5-trimethylbenzene (TMB), and the enlargement did not cause the variation of the mesostructure and particle morphology. The larger molecular size and higher hydrophobicity of TIPB than TMB induce the incorporation of TIPB into micelles without the structural change. When TMB was used as TAB, the pore size of CMSS was also enlarged while the mesostructure and particle morphology were varied. Interestingly, when tetramethoxysilane and TIPB were used, CMSS with a very small particle diameter (20 nm) with concave surfaces and large mesopores were obtained, which may strongly be related to the initial nucleation of CMSS. A judicious choice of TAB and Si sources is quite important to control the mesostructure, size of mesopores, particle diameter, and morphology.Both the pore size and particle diameter of aqueous colloidal mesostructured/mesoporous silica nanoparticles (CMSS/CMPS) derived from tetrapropoxysilane were effectively and easily controlled by the addition of trialkylbenzenes (TAB). Aqueous highly dispersed CMPS with large pores were successfully obtained through removal of surfactants and TAB by a dialysis process. The pore size (from 4 nm to 8 nm) and particle diameter (from 50 nm to 380 nm) were more effectively enlarged by the addition of 1,3,5-triisopropylbenzene (TIPB) than 1,3,5-trimethylbenzene (TMB), and the enlargement did not cause the variation of the mesostructure and particle morphology. The larger molecular size and higher hydrophobicity of TIPB than TMB induce the incorporation of TIPB into micelles without the structural change. When TMB was used as TAB, the pore size of CMSS was also enlarged while the mesostructure and particle morphology were varied. Interestingly, when tetramethoxysilane and TIPB were used, CMSS with a very small particle diameter (20 nm) with concave surfaces and large mesopores were obtained, which may strongly be related to the initial nucleation of CMSS. A judicious choice of TAB and Si sources is quite important to control the mesostructure, size of mesopores, particle diameter, and morphology. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04465k

Universal Assembly for Captive Bolts

NASA Technical Reports Server (NTRS)

Marke, M. L.; Hagopian, B.

1982-01-01

New method allows for virtually any bolt to be easily converted to "captive" bolt. Method eliminates need for separate design for each application. Cup-shaped washer that is flattened secures tap to bolt. Wire attached to tab holds bolt assembly captive. Flattening washer can also be done during installation of bolt. Wash, tab and spacer are all made of corrosion-resistant steel.

76 FR 419 - Airworthiness Directives; 328 Support Services GmbH (Type Certificate Previously Held by AvCraft...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-05

... cracking was identified as stress corrosion. This condition, if not corrected, could lead to in-flight... identified as stress corrosion. This condition, if not corrected, could lead to in-flight failure of the tab..., using a material that is more resistant to stress corrosion. The improved material rudder spring tab...

Civilian Human Resources

Science.gov Websites

open the menu (new window). Open Menu Navigate Up This page location is: Civilian Human Resources Pages Default BrowseTab 1 of 2. PageTab 2 of 2. Sign In You are leaving the Civilian Human Resources Website LinkedIn Search this site... Search Civilian Human Resources Top Link Bar Civilian Human Resources Home

Texas Assessment of Basic Skills (TABS). Austin Independent School District. Final Report, 1985.

ERIC Educational Resources Information Center

Defino, Maria E.

This report presents the Austin (Texas) Independent School District's 1985 test results on the Texas Assessment of Basic Skills (TABS). It was administered to all third, fifth, and ninth grade students and to high school students not meeting ninth grade state-set mastery criteria, the minimum competency requirement for graduation. Results are…

76 FR 62873 - Self-Regulatory Organizations; NYSE Arca, Inc.; Order Granting Approval of Proposed Rule Change...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-11

... registered with the Commission as an open-end management investment company.\\4\\ The investment adviser to the Fund is AdvisorShares Investments, LLC (``Adviser''). Trim Tabs Asset Management, LLC (``TrimTabs'' or... is registered under the Investment Company Act of 1940 (``1940 Act''). On January 19, 2011, the Trust...

Passive zero-gravity leg restraint

NASA Technical Reports Server (NTRS)

Miller, Christopher R. (Inventor)

1989-01-01

A passive zero or microgravity leg restraint is described which includes a central support post with a top and a bottom. Extending from the central support post are a calf pad tab, to which calf pad is attached, and a foot pad tab, to which foot tab is attached. Also extending from central support post are knee pads. When the restraint is in use the user's legs are forced between pads by a user imposed scissors action of the legs. The user's body is then supported in a zero or microgravity neutral body posture by the leg restraint. The calf pad has semi-ridig elastic padding material covering structural stiffener. The foot pad has padding material and a structural stiffener. Knee pads have s structural tube stiffener at their core.

Systemic malignancies presenting as primary osteolytic lesion.

PubMed

Sirelkhatim, A; Kaiserova, E; Kolenova, A; Puskacova, J; Subova, Z; Petrzalkova, D; Banikova, K; Suvada, J; Sejnova, D

2009-01-01

The tumor formation may be the earliest manifestation preceeding other symptoms, signs and bone marrow evidence of systemic malignancy - leukemia/lymphoma. Here we present three cases of systemic malignancy in which bone lesions were the first manifested signs of the disease. All three cases were thought to be orthopedic cases and had been treated as so without genuing improvement. We would like to draw an attention to children who present with multifocal musculoskeletal pain and the importance of whole-body scaning. We describe interesting cases of diffuse large cell lymphoma and leukemia that initially presented as primary osteolytic bone lesion and discuss the differential diagnosis, literature review of non-Hodgkin's lymphoma arising in bone as the primary site (Tab. 1, Fig. 3, Ref. 18). Full Text (Free, PDF) www.bmj.sk.

Improved fatigue performance for wood-based structural panels using slot and tab construction

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2016-01-01

This paper presents static and fatigue bending behavior for a wood-based structural panel having a slot and tab (S/T) construction technique. Comparisons were made with similarly fabricated panels without the S/T construction technique. Experimental results showed that both types of panels had similar bending properties in the static tests. However, the panels with S/T...

An Introductory Guide to TOPS-20.

DTIC Science & Technology

1982-06-01

344@\\4859@\\5938@\\495 @\\3988@\\3975@\\384@\\394 M\\@\\397@\\2987 @tabcl ear @tabdivide[5J @\\234@\\ 8796 @\\9876@\\986 @\\2368@\\123@\\6797@\\23 @\\37545@\\2346@\\3759...prs file 8.6.1. Setting Tabs 344 4859 5938 495 3988 3975 384 394 397 2987 234 8796 9876 986 2368 123 6797 23 37545 2346 3759 234 I 8.6.2. Tabs used

[Study on the matching of the shade between beverage and modifying porcelain shade guide].

PubMed

Yao, Jiang-wu; Li, Shui-gen; Lin, Jin-ying

2007-10-01

To evaluate the matching of the shade between beverage and modifying porcelain shade guide according to Munsell color order system, thus to provide the reference basis for selecting modifying porcelain to mimic the stain of natural tooth by technician. The shade of Vita Akzent, Vita Interno, Shofu Vintage & Unibond and Noritake Super Porcelain EX-3 shade tabs as well as 15 kinds of beverage were measured according to Munsell color order system on Color-Eye 7000A spectrophotometer. The difference of the frequency of approximate hue, value, and chroma between shade tabs and beverage were compared by calculating the Fisher exact probabilities. The frequency of approximate hue between 4 kinds of shade tabs and 15 kinds of bev-erage was significant different (P<0.05), while the frequency of approximate value, and chroma was not significant different (P>0.05). Except the hue, the color distribution of 4 kinds of shade tabs was similar to that of 15 kinds of beverage. But the color of beverage also can be approximately matched by any kind of modifying porcelain by mixing porcelain powder of appropriate hue, value, and chroma.

Ergonomics Designs of Aluminum Beverage Cans and Bottles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han Jing; Itoh, Ryouiti; Shinguryo, Takuro

2005-08-05

This paper introduced the finite element analyses into the ergonomics designs to evaluate the human feelings numerically and objectively. Two design examples in developing aluminum beverage cans and bottles are presented. The first example describes a design of the tab of the can with better finger access. A simulation of finger pulling up the tab of the can has been performed and a pain in the finger has been evaluated by using the maximum value of the contact stress of a finger model. The finger access comparison of three kinds of tab ring shape designs showed that the finger accessmore » of the tab that may have a larger contact area with finger is better. The second example describes a design of rib-shape embossed bottles for hot vending. Analyses of tactile sensation of heat have been performed and the amount of heat transmitted from hot bottles to finger was used to present the hot touch feeling. Comparison results showed that the hot touch feeling of rib-shape embossed bottles is better than that of cylindrical bottles, and that the shape of the rib also influenced the hot touch feeling.« less

A new approach to the internal thermal management of cylindrical battery cells for automotive applications

NASA Astrophysics Data System (ADS)

Worwood, Daniel; Kellner, Quirin; Wojtala, Malgorzata; Widanage, W. D.; M^cGlen, Ryan; Greenwood, David; Marco, James

2017-04-01

Conventional cooling approaches that target either a singular tab or outer surface of common format cylindrical lithium-ion battery cells suffer from a high cell thermal resistance. Under an aggressive duty cycle, this resistance can result in the formation of large in-cell temperature gradients and high hot spot temperatures, which are known to accelerate ageing and further reduce performance. In this paper, a novel approach to internal thermal management of cylindrical battery cells to lower the thermal resistance for heat transport through the inside of the cell is investigated. The effectiveness of the proposed method is analysed for two common cylindrical formats when subject to highly aggressive electrical loading conditions representative of a high performance electric vehicle (EV) and hybrid electric vehicle (HEV). A mathematical model that captures the dominant thermal properties of the cylindrical cell is created and validated using experimental data. Results from the extensive simulation study indicate that the internal cooling strategy can reduce the cell thermal resistance by up to 67.8 ± 1.4% relative to single tab cooling, and can emulate the performance of a more complex pack-level double tab cooling approach whilst targeting cooling at a single tab.

Some Tests and Calculations Pertaining to the Dive Path and to Wing and Tail Loads in the Accident to Eastern Airlines C54B Airplane, NC-88814, Near Bainbridge, Maryland, May 30, 1947

NASA Technical Reports Server (NTRS)

Rhode, Richard V.; Stokke, Allen R.; Rogin, Leo

1947-01-01

Several dive paths were calculated for a C54 airplane starting from level flight at an altitude of 4000 feet and from an initial indicated airspeed of 200 miles per hour. The results show that, within the limits of the possible paths permitted by the evidence of the crash at Bainbridge, the speed of impact would be about 370 miles per hour and the time to crash would be between 12 1/2 and 15 1/2 seconds. Tail load calculations indicate that, with moderate negative acceleration of the airplane, the tail would fail near the end of the dive in a manner consistent in several important respects with the evidence. A number of tests were made of the elevator tab control system to determine whether the tab would move by an amount sufficient to have caused the observed dive if the stored energy in the tab control cable were suddenly released. The results of these tests indicated that the probable tab movement is such as to be capable of causing a dive similar to the one observed at Bainbridge.

Synergistic Effect of TPD7 and Berberine against Leukemia Jurkat Cell Growth through Regulating Ephrin-B2 Signaling.

PubMed

Ma, Weina; Zhu, Man; Yang, Liu; Yang, Tianfeng; Zhang, Yanmin

2017-09-01

TPD7, a novel biphenyl urea taspine derivative, and berberine have presented inhibition on VEGFR2 that can be regulated by ephrin-B2 reverse signaling through interactions with the PDZ domain. The purpose of this study is to investigate the inhibitory effect of the combination of TPD7 and berberine (TAB) on T-cell acute lymphoblastic leukemia cell growth. TPD7 and berberine together synergistically inhibited the proliferation of Jurkat cells. Also, the combination of TAB induced G 1 -phase cell-cycle arrest by downregulating the level of cyclin D1, cyclin E, and CDC2. Furthermore, the combination of TAB significantly enhanced apoptosis in Jurkat cells, and the apoptosis most likely resulted from the modulation of the level of Bcl-2 family members. Most importantly, the concomitant treatment simultaneously regulated the ephrin-B2 and VEGFR2 signaling, as well as modulated the MEK/ERK and PTEN/PI3K/AKT/mTOR signaling. Therefore, the combination treatment of TAB may be a promising therapeutic method in treating T-cell acute lymphoblastic leukemia. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

3D Thermal and Electrochemical Model for Spirally Wound Large Format Lithium-ion Batteries (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, K. J.; Kim, G. H.; Smith, K.

In many commercial cells, long tabs at both cell sides, leading to uniform potentials along the spiral direction of wound jelly rolls, are rarely seen because of their high manufacturing cost. More often, several metal strips are welded at discrete locations along both current collector foils. With this design, the difference of electrical potentials is easily built up along current collectors in the spiral direction. Hence, the design features of the tabs, such as number, location and size, can be crucial factors for spiral-shaped battery cells. This paper presents a Li-ion battery cell model having a 3-dimensional spiral mesh involvingmore » a wound jellyroll structure. Further results and analysis will be given regarding impacts of tab location, number, and size.« less

Leaf seal for inner and outer casings of a turbine

DOEpatents

Schroder, Mark Stewart; Leach, David

2002-01-01

A plurality of arcuate, circumferentially extending leaf seal segments form an annular seal spanning between annular sealing surfaces of inner and outer casings of a turbine. The ends of the adjoining seal segments have circumferential gaps to enable circumferential expansion and contraction of the segments. The end of a first segment includes a tab projecting into a recess of a second end of a second segment. Edges of the tab seal against the sealing surfaces of the inner and outer casings have a narrow clearance with opposed edges of the recess. An overlying cover plate spans the joint. Leakage flow is maintained at a minimum because of the reduced gap between the radially spaced edges of the tab and recess, while the seal segments retain the capacity to expand and contract circumferentially.

Localization and Classification of Paddy Field Pests using a Saliency Map and Deep Convolutional Neural Network.

PubMed

Liu, Ziyi; Gao, Junfeng; Yang, Guoguo; Zhang, Huan; He, Yong

2016-02-11

We present a pipeline for the visual localization and classification of agricultural pest insects by computing a saliency map and applying deep convolutional neural network (DCNN) learning. First, we used a global contrast region-based approach to compute a saliency map for localizing pest insect objects. Bounding squares containing targets were then extracted, resized to a fixed size, and used to construct a large standard database called Pest ID. This database was then utilized for self-learning of local image features which were, in turn, used for classification by DCNN. DCNN learning optimized the critical parameters, including size, number and convolutional stride of local receptive fields, dropout ratio and the final loss function. To demonstrate the practical utility of using DCNN, we explored different architectures by shrinking depth and width, and found effective sizes that can act as alternatives for practical applications. On the test set of paddy field images, our architectures achieved a mean Accuracy Precision (mAP) of 0.951, a significant improvement over previous methods.

Economic 3D-printing approach for transplantation of human stem cell-derived β-like cells

PubMed Central

Song, Jiwon; Millman, Jeffrey R.

2016-01-01

Transplantation of human pluripotent stem cells (hPSC) differentiated into insulin-producing β cells is a regenerative medicine approach being investigated for diabetes cell replacement therapy. This report presents a multifaceted transplantation strategy that combines differentiation into stem cell-derived β (SC-β) cells with 3D printing. By modulating the parameters of a low-cost 3D printer, we created a macroporous device composed of polylactic acid (PLA) that houses SC-β cell clusters within a degradable fibrin gel. Using finite element modeling of cellular oxygen diffusion-consumption and an in vitro culture system that allows for culture of devices at physiological oxygen levels, we identified cluster sizes that avoid severe hypoxia within 3D-printed devices and developed a microwell-based technique for resizing clusters within this range. Upon transplantation into mice, SC-β cell-embedded 3D-printed devices function for 12 weeks, are retrievable, and maintain structural integrity. Here, we demonstrate a novel 3D-printing approach that advances the use of differentiated hPSC for regenerative medicine applications and serves as a platform for future transplantation strategies. PMID:27906687

Mesenchymal Stem Cell Preparation and Transfection-free Ferumoxytol Labeling for MRI Cell Tracking.

PubMed

Liu, Li; Ho, Chien

2017-11-15

Mesenchymal stem cells (MSCs) are multipotent cells and are the most widely studied cell type for stem cell therapies. In vivo cell tracking of MSCs labeled with an FDA-approved superparamagnetic iron-oxide (SPIO) particle by magnetic resonance imaging (MRI) provides essential information, e.g., MSC engraftment, survival, and fate, thus improving cell therapy accuracy. However, current methodology for labeling MSCs with Ferumoxytol (Feraheme ® ), the only FDA-approved SPIO particle, needs transfection agents. This unit describes a new "bio-mimicry" protocol to prepare more native MSCs by using more "in vivo environment" of MSCs, so that the phagocytic activity of cultured MSCs is restored and expanded MSCs can be labeled with Ferumoxytol, without the need for transfection agents and/or electroporation. Moreover, MSCs re-size to a more native size, reducing from 32.0 to 19.5 μm. The MSCs prepared from this protocol retain more native properties and would be useful for biomedical applications and MSC-tracking studies by MRI. © 2017 by John Wiley & Sons, Inc. Copyright © 2017 John Wiley & Sons, Inc.

High frequency dynamic engine simulation. [TF-30 engine

NASA Technical Reports Server (NTRS)

Schuerman, J. A.; Fischer, K. E.; Mclaughlin, P. W.

1977-01-01

A digital computer simulation of a mixed flow, twin spool turbofan engine was assembled to evaluate and improve the dynamic characteristics of the engine simulation to disturbance frequencies of at least 100 Hz. One dimensional forms of the dynamic mass, momentum and energy equations were used to model the engine. A TF30 engine was simulated so that dynamic characteristics could be evaluated against results obtained from testing of the TF30 engine at the NASA Lewis Research Center. Dynamic characteristics of the engine simulation were improved by modifying the compression system model. Modifications to the compression system model were established by investigating the influence of size and number of finite dynamic elements. Based on the results of this program, high frequency engine simulations using finite dynamic elements can be assembled so that the engine dynamic configuration is optimum with respect to dynamic characteristics and computer execution time. Resizing of the compression systems finite elements improved the dynamic characteristics of the engine simulation but showed that additional refinements are required to obtain close agreement simulation and actual engine dynamic characteristics.

Economic 3D-printing approach for transplantation of human stem cell-derived β-like cells.

PubMed

Song, Jiwon; Millman, Jeffrey R

2016-12-01

Transplantation of human pluripotent stem cells (hPSC) differentiated into insulin-producing β cells is a regenerative medicine approach being investigated for diabetes cell replacement therapy. This report presents a multifaceted transplantation strategy that combines differentiation into stem cell-derived β (SC-β) cells with 3D printing. By modulating the parameters of a low-cost 3D printer, we created a macroporous device composed of polylactic acid (PLA) that houses SC-β cell clusters within a degradable fibrin gel. Using finite element modeling of cellular oxygen diffusion-consumption and an in vitro culture system that allows for culture of devices at physiological oxygen levels, we identified cluster sizes that avoid severe hypoxia within 3D-printed devices and developed a microwell-based technique for resizing clusters within this range. Upon transplantation into mice, SC-β cell-embedded 3D-printed devices function for 12 weeks, are retrievable, and maintain structural integrity. Here, we demonstrate a novel 3D-printing approach that advances the use of differentiated hPSC for regenerative medicine applications and serves as a platform for future transplantation strategies.

Localization and Classification of Paddy Field Pests using a Saliency Map and Deep Convolutional Neural Network

PubMed Central

Liu, Ziyi; Gao, Junfeng; Yang, Guoguo; Zhang, Huan; He, Yong

2016-01-01

We present a pipeline for the visual localization and classification of agricultural pest insects by computing a saliency map and applying deep convolutional neural network (DCNN) learning. First, we used a global contrast region-based approach to compute a saliency map for localizing pest insect objects. Bounding squares containing targets were then extracted, resized to a fixed size, and used to construct a large standard database called Pest ID. This database was then utilized for self-learning of local image features which were, in turn, used for classification by DCNN. DCNN learning optimized the critical parameters, including size, number and convolutional stride of local receptive fields, dropout ratio and the final loss function. To demonstrate the practical utility of using DCNN, we explored different architectures by shrinking depth and width, and found effective sizes that can act as alternatives for practical applications. On the test set of paddy field images, our architectures achieved a mean Accuracy Precision (mAP) of 0.951, a significant improvement over previous methods. PMID:26864172

Modeling Progressive Failure of Bonded Joints Using a Single Joint Finite Element

NASA Technical Reports Server (NTRS)

Stapleton, Scott E.; Waas, Anthony M.; Bednarcyk, Brett A.

2010-01-01

Enhanced finite elements are elements with an embedded analytical solution which can capture detailed local fields, enabling more efficient, mesh-independent finite element analysis. In the present study, an enhanced finite element is applied to generate a general framework capable of modeling an array of joint types. The joint field equations are derived using the principle of minimum potential energy, and the resulting solutions for the displacement fields are used to generate shape functions and a stiffness matrix for a single joint finite element. This single finite element thus captures the detailed stress and strain fields within the bonded joint, but it can function within a broader structural finite element model. The costs associated with a fine mesh of the joint can thus be avoided while still obtaining a detailed solution for the joint. Additionally, the capability to model non-linear adhesive constitutive behavior has been included within the method, and progressive failure of the adhesive can be modeled by using a strain-based failure criteria and re-sizing the joint as the adhesive fails. Results of the model compare favorably with experimental and finite element results.

Small transport aircraft technology propeller study

NASA Technical Reports Server (NTRS)

Black, B. M.; Magliozzi, B.; Rohrbach, C.

1983-01-01

A study to define potential benefits of advanced technology propeller for 1985-1990 STAT commuter airplanes was completed. Two baselines, a Convair, 30 passenger, 0.47 Mach number airplane and a Lockheed, 50 passenger, 0.70 Mach number airplane, were selected from NASA-Ames sponsored airframe contracts. Parametric performance, noise level, weight and cost trends for propellers with varying number of blades, activity factor, camber and diameter incorporating blade sweep, tip proplets, advanced composite materials, advanced airfoils, advanced prevision synchrophasing and counter-rotation are presented. The resulting DOC, fuel burned, empty weight and acquisition cost benefits are presented for resizings of the two baseline airplanes. Six-bladed propeller having advanced composite blades, advanced airfoils, tip proplets and advanced prevision synchrophasers provided the maximum DOC improvements for both airplanes. DOC and fuel burned were reduced by 8.3% and 17.0% respectively for the Convair airplane and by 24.9% and 41.2% respectively for the Lockheed airplane. The larger reductions arose from a baseline definition with very heavy fuselage acoustic treatment. An alternate baseline, with a cabin noise 13dB in excess of the objective, was also studied.

Performances of multiprocessor multidisk architectures for continuous media storage

NASA Astrophysics Data System (ADS)

Gennart, Benoit A.; Messerli, Vincent; Hersch, Roger D.

1996-03-01

Multimedia interfaces increase the need for large image databases, capable of storing and reading streams of data with strict synchronicity and isochronicity requirements. In order to fulfill these requirements, we consider a parallel image server architecture which relies on arrays of intelligent disk nodes, each disk node being composed of one processor and one or more disks. This contribution analyzes through bottleneck performance evaluation and simulation the behavior of two multi-processor multi-disk architectures: a point-to-point architecture and a shared-bus architecture similar to current multiprocessor workstation architectures. We compare the two architectures on the basis of two multimedia algorithms: the compute-bound frame resizing by resampling and the data-bound disk-to-client stream transfer. The results suggest that the shared bus is a potential bottleneck despite its very high hardware throughput (400Mbytes/s) and that an architecture with addressable local memories located closely to their respective processors could partially remove this bottleneck. The point- to-point architecture is scalable and able to sustain high throughputs for simultaneous compute- bound and data-bound operations.

Cement paste surface roughness analysis using coherence scanning interferometry and confocal microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Apedo, K.L., E-mail: apedo@unistra.fr; Munzer, C.; He, H.

2015-02-15

Scanning electron microscopy and scanning probe microscopy have been used for several decades to better understand the microstructure of cementitious materials. Very limited work has been performed to date to study the roughness of cementitious materials by optical microscopy such as coherence scanning interferometry (CSI) and chromatic confocal sensing (CCS). The objective of this paper is to better understand how CSI can be used as a tool to analyze surface roughness and topography of cement pastes. Observations from a series of images acquired using this technique on both polished and unpolished samples are described. The results from CSI are comparedmore » with those from a STIL confocal microscopy technique (SCM). Comparison between both optical techniques demonstrates the ability of CSI to measure both polished and unpolished cement pastes. - Highlights: • Coherence scanning interferometry (CSI) was used to analyze cement paste surfaces. • The results from the CSI were compared with those from a confocal microscopy. • 3D roughness parameters were obtained using the window resizing method. • Polished and unpolished cement pastes were studied.« less

Hospital downsizing and workforce reduction strategies: some inner workings.

PubMed

Weil, Thomas P

2003-02-01

Downsizing, manpower reductions, re-engineering, and resizing are used extensively in the United States to reduce cost and to evaluate the effectiveness and efficiency of various functions and processes. Published studies report that these managerial strategies result in a minimal impact on access to services, quality of care, and the ability to reduce costs. But, these approaches certainly alienate employees. These findings are usually explained by the significant difficulties experienced in eliminating nursing and other similar direct patient care-oriented positions and in terminating white-collar employees. Possibly an equally plausible reason why hospitals and physician practices react so poorly to these management strategies is their cost structure-high fixed (85%) and low variable (15%)-and that simply generating greater volume does not necessarily achieve economies of scale. More workable alternatives for health executives to effectuate cost reductions consist of simplifying prepayment, decreasing the overall availability and centralizing tertiary services at academic health centres, and closing superfluous hospitals and other health facilities. America's pluralistic values and these proposals having serious political repercussions for health executives and elected officials often present serious barriers in their implementation.

Advanced Supersonic Technology concept AST-100 characteristics developed in a baseline-update study

NASA Technical Reports Server (NTRS)

Baber, H. T., Jr.; Swanson, E. E.

1976-01-01

The advanced supersonic technology configuration, AST-100, is described. The combination of wing thickness reduction, nacelle recontouring for minimum drag at cruise, and the use of the horizontal tail to produce lift during climb and cruise resulted in an increase in maximum lift-to-drag ratio. Lighter engines and lower fuel weight associated with this resizing result in a six percent reduction in takeoff gross weight. The AST-100 takeoff maximum effective perceived noise at the runway centerline and sideline measurement stations was 114.4 decibels. Since 1.5-decibels tradeoff is available from the approach noise, the required engine noise supression is 4.9 decibels. The AST-100 largest maximum overpressure would occur during transonic climb acceleration when the aircraft was at relatively low altitude. Calculated standard +8 C day range of the AST-100, with a 292 passenger payload, is 7348 km (3968 n.mi). Fuel price is the largest contributor to direct operating cost. However, if the AST-100 were flown subsonically (M = 0.9), direct operating costs would increase approximately 50 percent because of time related costs.

Depth-aware image seam carving.

PubMed

Shen, Jianbing; Wang, Dapeng; Li, Xuelong

2013-10-01

Image seam carving algorithm should preserve important and salient objects as much as possible when changing the image size, while not removing the secondary objects in the scene. However, it is still difficult to determine the important and salient objects that avoid the distortion of these objects after resizing the input image. In this paper, we develop a novel depth-aware single image seam carving approach by taking advantage of the modern depth cameras such as the Kinect sensor, which captures the RGB color image and its corresponding depth map simultaneously. By considering both the depth information and the just noticeable difference (JND) model, we develop an efficient JND-based significant computation approach using the multiscale graph cut based energy optimization. Our method achieves the better seam carving performance by cutting the near objects less seams while removing distant objects more seams. To the best of our knowledge, our algorithm is the first work to use the true depth map captured by Kinect depth camera for single image seam carving. The experimental results demonstrate that the proposed approach produces better seam carving results than previous content-aware seam carving methods.

Postsecondary Institutions in the United States: Fall 2004 and Degrees and Other Awards Conferred: 2003-04. E.D. TAB. NCES 2005-182

ERIC Educational Resources Information Center

Knapp, Laura G.; Kelly-Reid, Janice E.; Whitmore, Roy W.; Cong, June; Levine, Burton; Berzofsky, Marcus; Broyles, Susan G.

2005-01-01

This E.D. TAB presents findings from the Integrated Postsecondary Education Data System (IPEDS) fall 2004 data collection, which included two survey components: Institutional Characteristics for the 2004-05 academic year, and Completions covering the period July 1, 2003, through June 30, 2004. These data were collected through the IPEDS web-based…

Employees in Postsecondary Institutions, Fall 2004, and Salaries of Full-Time Instructional Faculty, 2004-05. E.D. TAB. NCES 2006-187

ERIC Educational Resources Information Center

Knapp, Laura G.; Kelly-Reid, Janice E.; Whitmore, Roy W.; Levine, Burton; Broyles, Susan G.; Huh, Seungho; Broyles, Susan G.

2006-01-01

This E.D. TAB presents findings from the Integrated Postsecondary Education Data System (IPEDS) Winter 2004-05 data collection, which included two required survey components: Employees by Assigned Position (EAP) for fall 2004 and Salaries (SA) for academic year 2004-05; the Fall Staff (S) component was optional for fall 2004. These data were…

Enrollment in Postsecondary Institutions, Fall 2003; Graduation Rates 1997 & 2000 Cohorts; and Financial Statistics, Fiscal Year 2003. E.D. TAB. NCES 2005-177

ERIC Educational Resources Information Center

Knapp, Laura G.; Kelly-Reid, Janice E.; Whitmore, Roy W.; Huh, Seungho; Levine, Burton; Berzofsky, Marcus

2005-01-01

This E.D. TAB presents findings from the Integrated Postsecondary Education Data System (IPEDS) Spring 2004 data collection, which included four survey components: Student Financial Aid for full-time, first-time, degree/certificate-seeking undergraduate students for the 2002-03 academic year, Enrollment for fall 2003, Graduation Rates for…

Light shield for solar concentrators

DOEpatents

Plesniak, Adam P.; Martins, Guy L.

2014-08-26

A solar receiver unit including a housing defining a recess, a cell assembly received in the recess, the cell assembly including a solar cell, and a light shield received in the recess and including a body and at least two tabs, the body defining a window therein, the tabs extending outward from the body and being engaged with the recess, wherein the window is aligned with the solar cell.

Fire-climate relationships and long-lead seasonal wildfire prediction for Hawaii

Treesearch

Pao-Shin Chu; Weiping Yan; Francis Fujioka

2002-01-01

We examined statistical relationships between the seasonal Southern Oscillation Index (SOI) and total acreages burned (TAB) and the number of fires in the Hawaiian Islands. A composite of TAB during four El Niño/ Southern Oscillation (ENSO) events reveals that a large total of acres burned is likely to occur from spring to summer in the year following an ENSO event....

Using Exploratory and Confirmatory Factor Analysis to Measure Construct Validity of the Traits, Aptitudes, and Behaviors Scale (TABS)

ERIC Educational Resources Information Center

Besnoy, Kevin D.; Dantzler, John; Besnoy, Lisa R.; Byrne, Caitlin

2016-01-01

This study evaluated the construct validity of the Traits, Aptitudes, and Behaviors Scale (TABS). Data for this study were collected from two separate school districts across three different academic years in the Southeastern United States. Of the total sample (N = 2,330), 64.6% of the children were identified as African American, 29.0% as…

Comparison of Sodium Chloride Tablets-Induced, Sodium Chloride Solution-Induced, and Glycerol-Induced Hyperhydration on Fluid Balance Responses in Healthy Men.

PubMed

Savoie, Félix A; Asselin, Audrey; Goulet, Eric D B

2016-10-01

Savoie, FA, Asselin, A, and Goulet, EDB. Comparison of sodium chloride tablets-induced, sodium chloride solution-induced, and glycerol-induced hyperhydration on fluid balance responses in healthy men. J Strength Cond Res 30(10): 2880-2891, 2016-Sodium chloride solution-induced hyperhydration (NaCl-SolIH) is a powerful strategy to increase body water before exercise. However, NaCl-SolIH is associated with an unpleasant salty taste, potentially dissuading some athletes from using it and coaches from recommending it. Therefore, we evaluated the hyperhydrating potential of sodium chloride tablets-induced hyperhydration (NaCl-TabIH), which bypasses the palatability issue of NaCl-SolIH without sacrificing sodium chloride content, and compared it to NaCl-SolIH and glycerol-induced hyperhydration (GIH). Sixteen healthy males (age: 21 ± 2 years; fat-free mass (FFM): 65 ± 6 kg) underwent three, 3-hour long passive hyperhydration protocols during which they drank, over the first 60 minutes, 30-ml·kg FFM of an artificially sweetened solution. During NaCl-TabIH, participants swallowed 7.5, 1 g each, sodium chloride tablets with every liter of solution. During NaCl-SolIH, an equal quantity of sodium chloride tablets was dissolved in each liter of solution. With GIH, the glycerol concentration was 46.7 g·L. Urine production, fluid retention, hemoglobin, hematocrit, plasma volume, and perceptual variables were monitored throughout the trials. Total fluid intake was 1948 ± 182 ml. After 3 hour, there were no significant differences among treatments for hemoglobin, hematocrit, and plasma volume changes. Fluid retention was significantly greater with NaCl-SolIH (1150 ± 287 ml) than NaCl-TabIH (905 ± 340 ml) or GIH (800 ± 211 ml), with no difference between NaCl-TabIH and GIH. No differences were found among treatments for perceptual variables. NaCl-TabIH and GIH are equally effective, but inferior than NaCl-SolIH. NaCl-TabIH represents an alternative to hyperhydration induced with glycerol, which is prohibited by the World Anti-Doping Agency.

Longitudinal change in patellofemoral cartilage thickness, cartilage T2 relaxation times, and subchondral bone plate area in adolescent vs mature athletes.

PubMed

Culvenor, Adam G; Wirth, Wolfgang; Maschek, Susanne; Boeth, Heide; Diederichs, Gerd; Duda, Georg; Eckstein, Felix

2017-07-01

Patellofemoral cartilage changes have been evaluated in knee trauma and osteoarthritis; however, little is known about changes in patellar and trochlear cartilage thickness, T2 relaxation-time and subchondral bone plate area (tAB) during growth. Our prospective study aimed to explore longitudinal change in patellofemoral cartilage thickness, T2 and tAB in adolescent athletes, and to compare these data with those of mature (i.e., adult) athletes. 20 adolescent (age 16±1years) and 20 mature (46±5years) volleyball players were studied over 2-years (10 men and 10 women each group). 1.5T MRI 3D-VIBE and multi-echo spin-echo sequences were acquired at baseline and 2-year follow-up. Using manual segmentation and 3D reconstruction, longitudinal changes in patellar and trochlear cartilage thickness, patellar cartilage T2 (mono-exponential decay curve with five echoes [9.7-67.9ms]), and patellar and trochlear tAB were determined. The annual increase in both patellar and trochlear cartilage thickness was 0.8% (95% confidence interval [CI] 0.6, 1.0) and 0.6% (0.3, 0.9), for adolescent males and females respectively; the longitudinal gain in patellar and trochlear tAB was 1.3% (1.1, 1.5) and 0.5% (0.2, 0.8), and 1.6% (1.1, 2.2) and 0.8% (0.3, 0.7) for adolescent males and females, respectively (no significant between-sex differences). Mature athletes showed smaller gains in tAB, and loss of <1% of cartilage thickness annually. While no significant sex-differences existed in adolescent patellar T2 changes, mature males gained significantly greater T2 than mature females (p=0.002-0.013). Patellar and trochlear cartilage thickness and tAB were observed to increase in young athletes in late adolescence, without significant differences between sexes. Mature athletes displayed patellar cartilage loss (and T2 increases in mature males), potentially reflecting degenerative changes. Copyright © 2017 Elsevier B.V. All rights reserved.

VizieR Online Data Catalog: Vela Junior (RX J0852.0-4622) HESS image (HESS+, 2018)

NASA Astrophysics Data System (ADS)

H. E. S. S. Collaboration; Abdalla, H.; Abramowski, A.; Aharonian, F.; Ait Benkhali, F.; Akhperjanian, A. G.; Andersson, T.; Anguener, E. O.; Arakawa, M.; Arrieta, M.; Aubert, P.; Backes, M.; Balzer, A.; Barnard, M.; Becherini, Y.; Becker Tjus, J.; Berge, D.; Bernhard, S.; Bernloehr, K.; Blackwell, R.; Boettcher, M.; Boisson, C.; Bolmont, J.; Bordas, P.; Bregeon, J.; Brun, F.; Brun, P.; Bryan, M.; Buechele, M.; Bulik, T.; Capasso, M.; Carr, J.; Casanova, S.; Cerruti, M.; Chakraborty, N.; Chalme-Calvet, R.; Chaves, R. C. G.; Chen, A.; Chevalier, J.; Chretien, M.; Coffaro, M.; Colafrancesco, S.; Cologna, G.; Condon, B.; Conrad, J.; Cui, Y.; Davids, I. D.; Decock, J.; Degrange, B.; Deil, C.; Devin, J.; Dewilt, P.; Dirson, L.; Djannati-Atai, A.; Domainko, W.; Donath, A.; Drury, L. O'c.; Dutson, K.; Dyks, J.; Edwards, T.; Egberts, K.; Eger, P.; Ernenwein, J.-P.; Eschbach, S.; Farnier, C.; Fegan, S.; Fernandes, M. V.; Fiasson, A.; Fontaine, G.; Foerster, A.; Funk, S.; Fuessling, M.; Gabici, S.; Gajdus, M.; Gallant, Y. A.; Garrigoux, T.; Giavitto, G.; Giebels, B.; Glicenstein, J. F.; Gottschall, D.; Goyal, A.; Grondin, M.-H.; Hahn, J.; Haupt, M.; Hawkes, J.; Heinzelmann, G.; Henri, G.; Hermann, G.; Hervet, O.; Hinton, J. A.; Hofmann, W.; Hoischen, C.; Holler, M.; Horns, D.; Ivascenko, A.; Iwasaki, H.; Jacholkowska, A.; Jamrozy, M.; Janiak, M.; Jankowsky, D.; Jankowsky, F.; Jingo, M.; Jogler, T.; Jouvin, L.; Jung-Richardt, I.; Kastendieck, M. A.; Katarzynski, K.; Katsuragawa, M.; Katz, U.; Kerszberg, D.; Khangulyan, D.; Khelifi, B.; Kieffer, M.; King, J.; Klepser, S.; Klochkov, D.; Kluzniak, W.; Kolitzus, D.; Komin, Nu.; Kosack, K.; Krakau, S.; Kraus, M.; Krueger, P. P.; Laffon, H.; Lamanna, G.; Lau, J.; Lees, J.-P.; Lefaucheur, J.; Lefranc, V.; Lemiere, A.; Lemoine-Goumard, M.; Lenain, J.-P.; Leser, E.; Lohse, T.; Lorentz, M.; Liu, R.; Lopez-Coto, R.; Lypova, I.; Marandon, V.; Marcowith, A.; Mariaud, C.; Marx, R.; Maurin, G.; Maxted, N.; Mayer, M.; Meintjes, P. J.; Meyer, M.; Mitchell, A. M. W.; Moderski, R.; Mohamed, M.; Mohrmann, L.; Mora, K.; Moulin, E.; Murach, T.; Nakashima, S.; de Naurois, M.; Niederwanger, F.; Niemiec J.; Oakes, L.; O'Brien, P.; Odaka, H.; Oettl, S.; Ohm, S.; Ostrowski, M.; Oya, I.; Padovani, M.; Panter, M.; Parsons, R. D.; Paz Arribas, M.; Pekeur, N. W.; Pelletier, G.; Perennes, C.; Petrucci, P.-O.; Peyaud, B.; Piel, Q.; Pita, S.; Poon, H.; Prokhorov, D.; Prokoph, H.; Puehlhofer, G.; Punch, M.; Quirrenbach, A.; Raab, S.; Reimer, A.; Reimer, O.; Renaud, M.; de Los Reyes, R.; Richter, S.; Rieger, F.; Romoli, C.; Rowell, G.; Rudak, B.; Rulten, C. B.; Sahakian, V.; Saito, S.; Salek, D.; Sanchez, D. A.; Santangelo, A.; Sasaki, M.; Schlickeiser, R.; Schuessler, F.; Schulz, A.; Schwanke, U.; Schwemmer, S.; Seglar-Arroyo, M.; Settimo, M.; Seyffert, A. S.; Shafi, N.; Shilon, I.; Simoni, R.; Sol, H.; Spanier, F.; Spengler, G.; Spies, F.; Stawarz, L.; Steenkamp, R.; Stegmann, C.; Stycz, K.; Sushch, I.; Takahashi, T.; Tavernet, J.-P.; Tavernier, T.; Taylor, A. M.; Terrier, R.; Tibaldo, L.; Tiziani, D.; Tluczykont, M.; Trichard, C.; Tsuji, N.; Tuffs, R.; Uchiyama, Y.; van der, Walt D. J.; van Eldik, C.; van Rensburg, C.; van Soelen, B.; Vasileiadis, G.; Veh, J.; Venter, C.; Viana, A.; Vincent, P.; Vink, J.; Voisin, F.; Voelk, H. J.; Vuillaume, T.; Wadiasingh, Z.; Wagner, S. J.; Wagner, P.; Wagner, R. M.; White, R.; Wierzcholska, A.; Willmann, P.; Woernlein, A.; Wouters, D.; Yang, R.; Zabalza, V.; Zaborov, D.; Zacharias, M.; Zanin, R.; Zdziarski, A. A.; Zech, A.; Zefi, F.; Ziegler, A.; Zywucka, N.

2018-03-01

skymap.fit: H.E.S.S. excess skymap in FITS format of the region comprising Vela Junior and its surroundings. The excess map has been corrected for the gradient of exposure and smoothed with a Gaussian function of width 0.08° to match the analysis point spread function, matching the procedure applied to derive the maps in Fig. 1. sp_stat.txt: H.E.S.S. spectral points and fit parameters for Vela Junior (H.E.S.S. data points in Fig. 3 and Tab. A.2 and H.E.S.S. spectral fit parameters in Tab. 4). The errors in this file represent statistical uncertainties at 1 sigma confidence level. The covariance matrix of the fit is also included in the format: c11 c12 c_13 c21 c22 c_23 c31 c32 c_33 where the subindices represent the following parameters of the power-law with exponential cut-off (ECPL) formula in Tab. 2: 1: flux normalization (Phi0) 2: spectral index (Gamma) 3: inverse of the cutoff energy (lambda=1/Ecut) The units for the covariance matrix are the same as for the fit parameters. Notice that, while the fit parameters section of the file shows E_cut as parameter, the fit was done in lambda=1/Ecut; hence the covariance matrix shows the values for lambda in TeV-1. sp_syst.txt: H.E.S.S. spectral points and fit parameters for Vela Junior (H.E.S.S. data points in Fig. 3 and Tab. A.2 and H.E.S.S. spectral fit parameters in Tab. 4). The errors in this file represent systematic uncertainties at 1 sigma confidence level. The integral fluxes for several energy ranges are also included. (4 data files).

The mzTab data exchange format: communicating mass-spectrometry-based proteomics and metabolomics experimental results to a wider audience.

PubMed

Griss, Johannes; Jones, Andrew R; Sachsenberg, Timo; Walzer, Mathias; Gatto, Laurent; Hartler, Jürgen; Thallinger, Gerhard G; Salek, Reza M; Steinbeck, Christoph; Neuhauser, Nadin; Cox, Jürgen; Neumann, Steffen; Fan, Jun; Reisinger, Florian; Xu, Qing-Wei; Del Toro, Noemi; Pérez-Riverol, Yasset; Ghali, Fawaz; Bandeira, Nuno; Xenarios, Ioannis; Kohlbacher, Oliver; Vizcaíno, Juan Antonio; Hermjakob, Henning

2014-10-01

The HUPO Proteomics Standards Initiative has developed several standardized data formats to facilitate data sharing in mass spectrometry (MS)-based proteomics. These allow researchers to report their complete results in a unified way. However, at present, there is no format to describe the final qualitative and quantitative results for proteomics and metabolomics experiments in a simple tabular format. Many downstream analysis use cases are only concerned with the final results of an experiment and require an easily accessible format, compatible with tools such as Microsoft Excel or R. We developed the mzTab file format for MS-based proteomics and metabolomics results to meet this need. mzTab is intended as a lightweight supplement to the existing standard XML-based file formats (mzML, mzIdentML, mzQuantML), providing a comprehensive summary, similar in concept to the supplemental material of a scientific publication. mzTab files can contain protein, peptide, and small molecule identifications together with experimental metadata and basic quantitative information. The format is not intended to store the complete experimental evidence but provides mechanisms to report results at different levels of detail. These range from a simple summary of the final results to a representation of the results including the experimental design. This format is ideally suited to make MS-based proteomics and metabolomics results available to a wider biological community outside the field of MS. Several software tools for proteomics and metabolomics have already adapted the format as an output format. The comprehensive mzTab specification document and extensive additional documentation can be found online. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

The mzTab Data Exchange Format: Communicating Mass-spectrometry-based Proteomics and Metabolomics Experimental Results to a Wider Audience*

PubMed Central

Griss, Johannes; Jones, Andrew R.; Sachsenberg, Timo; Walzer, Mathias; Gatto, Laurent; Hartler, Jürgen; Thallinger, Gerhard G.; Salek, Reza M.; Steinbeck, Christoph; Neuhauser, Nadin; Cox, Jürgen; Neumann, Steffen; Fan, Jun; Reisinger, Florian; Xu, Qing-Wei; del Toro, Noemi; Pérez-Riverol, Yasset; Ghali, Fawaz; Bandeira, Nuno; Xenarios, Ioannis; Kohlbacher, Oliver; Vizcaíno, Juan Antonio; Hermjakob, Henning

2014-01-01

The HUPO Proteomics Standards Initiative has developed several standardized data formats to facilitate data sharing in mass spectrometry (MS)-based proteomics. These allow researchers to report their complete results in a unified way. However, at present, there is no format to describe the final qualitative and quantitative results for proteomics and metabolomics experiments in a simple tabular format. Many downstream analysis use cases are only concerned with the final results of an experiment and require an easily accessible format, compatible with tools such as Microsoft Excel or R. We developed the mzTab file format for MS-based proteomics and metabolomics results to meet this need. mzTab is intended as a lightweight supplement to the existing standard XML-based file formats (mzML, mzIdentML, mzQuantML), providing a comprehensive summary, similar in concept to the supplemental material of a scientific publication. mzTab files can contain protein, peptide, and small molecule identifications together with experimental metadata and basic quantitative information. The format is not intended to store the complete experimental evidence but provides mechanisms to report results at different levels of detail. These range from a simple summary of the final results to a representation of the results including the experimental design. This format is ideally suited to make MS-based proteomics and metabolomics results available to a wider biological community outside the field of MS. Several software tools for proteomics and metabolomics have already adapted the format as an output format. The comprehensive mzTab specification document and extensive additional documentation can be found online. PMID:24980485

Release of Apical Dominance in Potato Tuber Is Accompanied by Programmed Cell Death in the Apical Bud Meristem[C][W

PubMed Central

Teper-Bamnolker, Paula; Buskila, Yossi; Lopesco, Yael; Ben-Dor, Shifra; Saad, Inbal; Holdengreber, Vered; Belausov, Eduard; Zemach, Hanita; Ori, Naomi; Lers, Amnon; Eshel, Dani

2012-01-01

Potato (Solanum tuberosum) tuber, a swollen underground stem, is used as a model system for the study of dormancy release and sprouting. Natural dormancy release, at room temperature, is initiated by tuber apical bud meristem (TAB-meristem) sprouting characterized by apical dominance (AD). Dormancy is shortened by treatments such as bromoethane (BE), which mimics the phenotype of dormancy release in cold storage by inducing early sprouting of several buds simultaneously. We studied the mechanisms governing TAB-meristem dominance release. TAB-meristem decapitation resulted in the development of increasing numbers of axillary buds with time in storage, suggesting the need for autonomous dormancy release of each bud prior to control by the apical bud. Hallmarks of programmed cell death (PCD) were identified in the TAB-meristems during normal growth, and these were more extensive when AD was lost following either extended cold storage or BE treatment. Hallmarks included DNA fragmentation, induced gene expression of vacuolar processing enzyme1 (VPE1), and elevated VPE activity. VPE1 protein was semipurified from BE-treated apical buds, and its endogenous activity was fully inhibited by a cysteinyl aspartate-specific protease-1-specific inhibitor N-Acetyl-Tyr-Val-Ala-Asp-CHO (Ac-YVAD-CHO). Transmission electron microscopy further revealed PCD-related structural alterations in the TAB-meristem of BE-treated tubers: a knob-like body in the vacuole, development of cytoplasmic vesicles, and budding-like nuclear segmentations. Treatment of tubers with BE and then VPE inhibitor induced faster growth and recovered AD in detached and nondetached apical buds, respectively. We hypothesize that PCD occurrence is associated with the weakening of tuber AD, allowing early sprouting of mature lateral buds. PMID:22362870

Energy demand and thermal comfort of HVAC systems with thermally activated building systems as a function of user profile

NASA Astrophysics Data System (ADS)

Pałaszyńska, Katarzyna; Bandurski, Karol; Porowski, Mieczysław

2017-11-01

Thermally Activated Building Systems (TABS) are a way to use building structure as a thermal energy storage. As a result, renewable energy sources may be used more efficiently. The paper presents numerical analysis of a HVAC system with TABS energy demand and indoor thermal comfort of a representative room in a non-residential building (governmental, commercial, educational). The purpose of analysis is to investigate the influence of a user profile on system performance. The time span of the analysis is one year - a typical meteorological year. The model was prepared using a generally accepted simulation tool - TRNSYS 17. The results help to better understand the interaction of a user profile with TABS. Therefore they are important for the development of optimal control algorithms for energy efficient buildings equipped with such systems.

Method and apparatus for mounting a dichroic mirror in a microwave powered lamp assembly using deformable tabs

DOEpatents

Ury, M.; Sowers, F.; Harper, C.; Love, W.

1998-11-24

A microwave powered electrodeless lamp includes an improved screen unit having mesh and solid sections with an internal reflector secured at the juncture of the two sections to reflect light into a light-transmitting chamber defined in the lamp microwave cavity by the reflector and the mesh section. A discharge envelope of a bulb is disposed in the light-transmitting chamber. Light emitted from the envelope is prevented by the reflector from entering the cavity portion bounded by the solid section of the screen. The reflector is mounted in the cavity by tabs formed in the screen unit and bendable into the cavity to define support planes abutting respective surfaces of the reflector. The mesh section and tabs are preferably formed by etching a thin metal sheet. 7 figs.

Method and apparatus for mounting a dichroic mirror in a microwave powered lamp assembly using deformable tabs

DOEpatents

Ury, Michael; Sowers, Frank; Harper, Curt; Love, Wayne

1998-01-01

A microwave powered electrodeless lamp includes an improved screen unit having mesh and solid sections with an internal reflector secured at the juncture of the two sections to reflect light into a light-transmitting chamber defined in the lamp microwave cavity by the reflector and the mesh section. A discharge envelope of a bulb is disposed in the light-transmitting chamber. Light emitted from the envelope is prevented by the reflector from entering the cavity portion bounded by the solid section of the screen. The reflector is mounted in the cavity by tabs formed in the screen unit and bendable into the cavity to define support planes abutting respective surfaces of the reflector. The mesh section and tabs are preferably formed by etching a thin metal sheet.

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 2: Tabulated data

NASA Technical Reports Server (NTRS)

Brown, W. H.; Ahuja, K. K.

1989-01-01

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. This volume contains tabulated data for each of the data runs cited in Volume 1. Baseline characteristics, mixing modifications (subsonic and supersonic, heated and unheated) and miscellaneous charts are included.

Testing and evaluation of a slot and tab construction technique for light-weight wood-fiber-based structural panels under bending

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2015-01-01

This paper presented construction and strain distributions for light-weight wood-fiber-based structural panels with tri-grid core made from phenolic impregnated laminated paper composites under bending. A new fastening configuration of slots in the faces and tabs on the core was applied to the face/core interfaces of the sandwich panel in addition to epoxy resin. Both...

Enrollment in Postsecondary Institutions, Fall 2004; Graduation Rates, 1998 & 2001 Cohorts; and Financial Statistics, Fiscal Year 2004 E.D. TAB. NCES 2006-155

ERIC Educational Resources Information Center

Knapp, Laura, G.; Kelly-Reid, Janice E.; Whitmore, Roy W.; Miller, Elise S.

2006-01-01

This E.D. TAB presents findings from the Integrated Postsecondary Education Data System (IPEDS) Spring 2005 data collection, which included four components: Student Financial Aid for full-time, first-time, degree/certificate-seeking undergraduate students for the 2003-04 academic year, Enrollment for fall 2004 and 12-month counts for 2003-04.…

Photovoltaic sheathing element with one or more tabs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keenihan, James R; Langmaid, Joseph A; Lopez, Leonardo C.

2017-02-07

The present invention is premised upon an assembly that includes at least a photovoltaic sheathing element capable of being affixed on a building structure. The shingle including at least a photovoltaic cell assembly, a body portion attached to one or more portions of the photovoltaic cell assembly. Wherein the body portion includes one or more top peripheral tabs each capable of fitting under one or more vertically adjoining devices.

Consistency in color parameters of a commonly used shade guide.

PubMed

Tashkandi, Esam

2010-01-01

The use of shade guides to assess the color of natural teeth subjectively remains one of the most common means for dental shade assessment. Any variation in the color parameters of the different shade guides may lead to significant clinical implications. Particularly, since the communication between the clinic and the dental laboratory is based on using the shade guide designation. The purpose of this study was to investigate the consistency of the L∗a∗b∗ color parameters of a sample of a commonly used shade guide. The color parameters of a total of 100 VITAPAN Classical Vacuum shade guide (VITA Zahnfabrik, Bad Säckingen, Germany(were measured using a X-Rite ColorEye 7000A Spectrophotometer (Grand Rapids, Michigan, USA). Each shade guide consists of 16 tabs with different designations. Each shade tab was measured five times and the average values were calculated. The ΔE between the average L∗a∗b∗ value for each shade tab and the average of the 100 shade tabs of the same designation was calculated. Using the Student t-test analysis, no significant differences were found among the measured sample. There is a high consistency level in terms of color parameters of the measured VITAPAN Classical Vacuum shade guide sample tested.

[Research on the designing method of a special shade guide for tooth whitening].

PubMed

Xu, Yingxin

2015-10-01

To investigate a method of designing an accurate and scientific shade guide, especially used for judging the effect of tooth whitening, by analyzing the colorimetric values of discolored teeth statistically. One hundred thirty-six pictures of patients who had been receiving the Beyond cold light whitening treatment from February 2009 to July 2014 were analyzed, including 25 tetracycline teeth, 61 mottled-enamel teeth, and 50 yellow teeth. The colorimetric values of discolored teeth were measured. The L* values of shade tabs were calculated by hierarchical clustering of those of discolored teeth. The a* and b* values of shade tabs were the mean of those observed for discolored teeth. Accordingly, different shade guides were designed for each type of discolored teeth, and the effects were evaluated. A statistically significant difference in colorimetric values was found among the three types of discolored teeth. Compared with the Vitapan Classical shade guide, the shade guides designed through the present method were more scientific and accurate in judging the effect of tooth whitening. Moreover, the arrangement of shade tabs was more logical, and the color difference between shade tabs and discolored teeth was smaller. The proposed designing method is theoretically feasible, although its clinical effect has yet to be proven.

Regular and irregular deswelling of polyacrylate and hyaluronate gels induced by oppositely charged surfactants.

PubMed

Nilsson, Peter; Hansson, Per

2008-09-15

The deswelling kinetics of macroscopic polyacrylate (PA) gels in solutions of dodecyltrimethylammonium bromide (C(12)TAB) and cetyltrimethylammonium bromide (C(16)TAB), with and without added sodium bromide, as well as hyaluronate (HA) gels in solutions of cetylpyridinium chloride (CPC) are investigated. Additional data are also provided by small-angle X-ray scattering and microgel experiments. The purpose is to study the deswelling behavior of (1) regularly deswelling gels, for which the deswelling is successfully described using a core/shell model earlier employed for microgels, and (2) irregularly deswelling gels, where the gel turns into a balloon-like structure with a dense outer layer surrounding a liquid-filled core. For regularly deswelling gels, the deswelling of PA/C(12)TAB is found to be controlled by diffusion through both stagnant layer and collapsed surface phase, while for PA/C(16)TAB it is found to be controlled mainly by the latter. The difference in deswelling rate between the two is found to correspond to the difference in surfactant diffusion coefficient in the surface phase. Factors found to promote irregular deswelling, described as balloon formation, are rapid surfactant binding, high bromide and surfactant concentration, longer surfactant chain length, and macroscopic gel size. Scattering data indicating a cubic structure for HA/CPC complexes are reported.

A Randomized Controlled Trial Provides Evidence to Support Aromatherapy to Minimize Anxiety in Women Undergoing Breast Biopsy.

PubMed

Trambert, Renee; Kowalski, Mildred Ortu; Wu, Betty; Mehta, Nimisha; Friedman, Paul

2017-10-01

Aromatherapy has been used to reduce anxiety in a variety of settings, but usefulness associated with breast biopsies has not been documented. This study was conducted in women undergoing image-guided breast biopsy. We explored the use of two different aromatherapy scents, compared to placebo, aimed at reducing anxiety with the intent of generating new knowledge. This was a randomized, placebo-controlled study of two different types of external aromatherapy tabs (lavender-sandalwood and orange-peppermint) compared with a matched placebo-control delivery system. Anxiety was self-reported before and after undergoing a breast biopsy using the Spielberger State Anxiety Inventory Scale. Eighty-seven women participated in this study. There was a statistically significant reduction in self-reported anxiety with the use of the lavender-sandalwood aromatherapy tab compared with the placebo group (p = .032). Aromatherapy tabs reduced anxiety during image-guided breast biopsy. The completion of the biopsy provided some relief from anxiety in all groups. The use of aromatherapy tabs offers an evidence-based nursing intervention to improve adaptation and reduce anxiety for women undergoing breast biopsy. Lavender-sandalwood aromatherapy reduced anxiety and promoted adaptation more than orange-peppermint aromatherapy or placebo. © 2017 Sigma Theta Tau International.

Impact of self-assembled surfactant structures on rheology of concentrated nanoparticle dispersions.

PubMed

Zaman, A A; Singh, P; Moudgil, B M

2002-07-15

Rheological behavior of surfactant-stabilized colloidal dispersions of silica particles under extreme conditions (low pH, high ionic strength) has been investigated in relation to interparticle forces and stability of the dispersion. The surfactant used as the dispersing agent was C(12)TAB, a cationic surfactant. Stability analysis through turbidity measurements indicated that there is a sharp increase in the stability of the dispersion when the surfactant concentration is in the range of 8 to 10 mM in the system. The state of the dispersion changes from an unstable regime to a stable regime above a critical concentration of C(12)TAB in the system. In the case of interaction forces measured between the silica substrate and AFM tip, no repulsive force was observed up to a surfactant concentration of 8 mM and a transition from no repulsive forces to steric repulsive forces occurred between 8 and 10 mM. Rheological measurements as a function of C(12)TAB concentration indicated a significant decrease in the viscosity and linear viscoelastic functions of the dispersion over the same range of surfactant concentration (8 to 10 mM C(12)TAB), showing a strong correlation between the viscosity behavior, interparticle forces, and structure development in the dispersion.

HGDB: A web retrieving cardiovascular-associated gene data.

PubMed

Noorabad-Ghahroodi, Faezeh; Abdi, Samaneh; Zand, Amir Hossein; Najafi, Mohammad

2017-04-01

The use of data obtained from high throughput techniques in genetics studies is an essential subject in biology. The system approaches of networking and enriching may improve the data management. Here, we annotated the molecular features for cardiovascular-associated genes and presented the HGDB search-based database (www.hgdb.ir). The initial seed data was primarily used from Gene Ontology and was automatically enriched with other molecular features. The data was managed in a SQL popular and open source. The search tabs on the HGDB homepage were applied for ID/Name Gene, chromosome, cell organelle and all gene options. The search results were presented on the gene text-based and source link-based descriptions. The HGDB is a friendly website to present gene data in the cardiovascular field. Copyright © 2017 Elsevier B.V. All rights reserved.

Fathers of U.S. Children Born in 2001: Findings from the Early Childhood Longitudinal Study, Birth Cohort (ECLS-B) E.D. TAB. NCES 2006-002

ERIC Educational Resources Information Center

Avenilla, Frank; Rosenthal, Emily; Tice, Pete

2006-01-01

This E.D. TAB presents information about the biological fathers of children born in the United States in the year 2001. It is the first publication of findings using the data collected from fathers during the base year collection of the Early Childhood Longitudinal Study, Birth Cohort (ECLS-B). It presents information on the demographic…

Cross-contact chain

NASA Technical Reports Server (NTRS)

Lieneweg, Udo (Inventor)

1988-01-01

A system is provided for use with wafers that include multiple integrated circuits that include two conductive layers in contact at multiple interfaces. Contact chains are formed beside the integrated circuits, each contact chain formed of the same two layers as the circuits, in the form of conductive segments alternating between the upper and lower layers and with the ends of the segments connected in series through interfaces. A current source passes a current through the series-connected segments, by way of a pair of current tabs connected to opposite ends of the series of segments. While the current flows, voltage measurements are taken between each of a plurality of pairs of voltage tabs, the two tabs of each pair connected to opposite ends of an interface that lies along the series-connected segments. A plot of interface conductances on a normal probability chart, enables prediction of the yield of good integrated circuits from the wafer.

Cross-contact chain

NASA Technical Reports Server (NTRS)

Lieneweg, U. (Inventor)

1986-01-01

A system is provided for use with wafers that include multiple integrated circuits that include two conductive layers in contact at multiple interfaces. Contact chains are formed beside the integrated circuits, each contact chain formed of the same two layers as the circuits, in the form of conductive segments alternating between the upper and lower layers and with the ends of the segments connected in series through interfaces. A current source passes a current through the series-connected segments, by way of a pair of current tabs connected to opposite ends of the series of segments. While the current flows, voltage measurements are taken between each of a plurality of pairs of voltage tabs, the two tabs of each pair connected to opposite ends of an interface that lies along the series-connected segments. A plot of interface conductances on normal probability chart enables prediction of the yield of good integrated circuits from the wafer.

Digital photocontrol of the network of live excitable cells

NASA Astrophysics Data System (ADS)

Erofeev, I. S.; Magome, N.; Agladze, K. I.

2011-11-01

Recent development of tissue engineering techniques allows creating and maintaining almost indefinitely networks of excitable cells with desired architecture. We coupled the network of live excitable cardiac cells with a common computer by sensitizing them to light, projecting a light pattern on the layer of cells, and monitoring excitation with the aid of fluorescent probes (optical mapping). As a sensitizing substance we used azobenzene trimethylammonium bromide (AzoTAB). This substance undergoes cis-trans-photoisomerization and trans-isomer of AzoTAB inhibits excitation in the cardiac cells, while cis-isomer does not. AzoTAB-mediated sensitization allows, thus, reversible and dynamic control of the excitation waves through the entire cardiomyocyte network either uniformly, or in a preferred spatial pattern. Technically, it was achieved by coupling a common digital projector with a macroview microscope and using computer graphic software for creating the projected pattern of conducting pathways. This approach allows real time interactive photocontrol of the heart tissue.

Differential effects of human interferon alpha and interferon gamma on xenografted human thyroid tissue in severe combined immunodeficient mice and nude mice.

PubMed

Kawai, K; Enomoto, T; Fornasier, V; Resetkova, E; Volpé, R

1997-03-01

We have studied the in vivo effects of human interferon alpha (IFN-alpha) and interferon gamma (IFN-gamma) administration on human thyroid tissue xenografted into two mouse strains: severe combined immunodeficient (SCID) mice and nude mice. Human lymphocytes survive in SCID mice but are lysed in nude mice. Thyroid tissues from Graves' disease or Hashimoto's thyroiditis, or paranodular [normal, (N)] tissue was xenografted into SCID mice (0.8 g/mouse) pretreated with anti-asialo GM-1 antiserum and radiation and also into nude mice. One week after xenografting, SCID and nude mice were divided into three groups. Group A was treated with IFN-alpha intraperitoneally (2,000 units/mouse) three times weekly; group B was treated with IFN-gamma similarly; group C was treated with phosphate buffered saline (PBS) only (control). Autologous human peripheral blood mononuclear cells (PBMCs) were added to mice receiving N xenografts. Blood was taken every 2 weeks for levels of IgG and thyroid antibodies (TAb). After 6 weeks of treatment, mice were sacrificed, and xenograft thyrocyte histocompatibility leukocyte antigen (HLA-DR) and intercellular adhesion molecule (ICAM-1) expression were measured. In addition, thyrocyte cultures were stimulated in vitro with 200 units/ml of either IFN-alpha or IFN-gamma or PBS (control). SCID mice xenografted with autoimmune thyroid disease (AITD) in group A showed a significantly higher TAb production than group C, whereas in group B, TAb production was not statistically increased compared to control (group C). SCID mice xenografted with N did not produce TAb in any group, nor did nude mice xenografted with AITD. Thyrocyte HLA-DR expression was markedly increased in group A and B in SCID mice xenografted with Graves' disease, Hashimoto's thyroiditis, and N tissue compared to group C. In contrast, only group B (IFN-gamma) showed an increase in thyrocyte HLA-DR in nude mice. In the in vitro studies, only IFN-gamma (not IFN-alpha) stimulated thyrocyte HLA-DR and ICAM-1 expression in Graves' disease, Hashimoto's thyroiditis, and N tissues. We concluded that in SCID mice, IFN-alpha causes TAB production in AITD xenografts but not in N xenografts, while increasing thyrocyte HLA-DR expression in both. Also, IFN-gamma does not cause a statistically increased TAb in AITD xenografts in SCID mice, despite a sharp rise in thyrocyte HLA-DR expression. In addition, because IFN-alpha has no effect in nude mice or in vitro on thyrocyte HLA-DR expression, its effects in SCID mice must be mediated via local infiltrating lymphocytes. Finally, IFN-gamma has a direct effect on thyrocytes to increase HLA-DR expression (and, in vitro, ICAM-1 expression) but may not stimulate TAb production.

Structure-Function Relationship of Hydrophiidae Postsynaptic Neurotoxins

DTIC Science & Technology

1992-03-11

monster venom concluded that gila toxin is an arginine esterase with kallikrein-like activity causing lethality and gyration in mice. However, it is not a...Fractionation of Lapemis venom ............ 49 Fig 3-4 Fractionation of Gila Toxin ............... 50 Fig 3-5 Fibrinogenolytic Activity of Gila toxin...Sequence of 8 kD Fragment of Lapemis PLA ..... 8 7 Tab 3-9 Enzyme Activity of Native and Metal Pl . 88 Tab 3-10 Amino Acid Analysis of Lapemis 9 kD prorein

Evaluation of Rhenium Joining Methods

NASA Technical Reports Server (NTRS)

Reed, Brian D.; Morren, Sybil H.

1995-01-01

Coupons of rhenium-to-Cl03 flat plate joints, formed by explosive and diffusion bonding, were evaluated in a series of shear tests. Shear testing was conducted on as-received, thermally-cycled (100 cycles, from 21 to 1100 C), and thermally-aged (3 and 6 hrs at 1100 C) joint coupons. Shear tests were also conducted on joint coupons with rhenium and/or Cl03 electron beam welded tabs to simulate the joint's incorporation into a structure. Ultimate shear strength was used as a figure of merit to assess the effects of the thermal treatment and the electron beam welding of tabs on the joint coupons. All of the coupons survived thermal testing intact and without any visible degradation. Two different lots of as-received, explosively-bonded joint coupons had ultimate shear strengths of 281 and 310 MPa and 162 and 223 MPa, respectively. As-received, diffusion-bonded coupons had ultimate shear strengths of 199 and 348 MPa. For the most part, the thermally-treated and rhenium weld tab coupons had shear strengths slightly reduced or within the range of the as-received values. Coupons with Cl03 weld tabs experienced a significant reduction in shear strength. The degradation of strength appeared to be the result of a poor heat sink provided during the electron beam welding. The Cl03 base material could not dissipate heat as effectively as rhenium, leading to the formation of a brittle rhenium-niobium intermetallic.

Reliability and accuracy of four dental shade-matching devices.

PubMed

Kim-Pusateri, Seungyee; Brewer, Jane D; Davis, Elaine L; Wee, Alvin G

2009-03-01

There are several electronic shade-matching instruments available for clinical use, but the reliability and accuracy of these instruments have not been thoroughly investigated. The purpose of this in vitro study was to evaluate the reliability and accuracy of 4 dental shade-matching instruments in a standardized environment. Four shade-matching devices were tested: SpectroShade, ShadeVision, VITA Easyshade, and ShadeScan. Color measurements were made of 3 commercial shade guides (Vitapan Classical, Vitapan 3D-Master, and Chromascop). Shade tabs were placed in the middle of a gingival matrix (Shofu GUMY) with shade tabs of the same nominal shade from additional shade guides placed on both sides. Measurements were made of the central region of the shade tab positioned inside a black box. For the reliability assessment, each shade tab from each of the 3 shade guide types was measured 10 times. For the accuracy assessment, each shade tab from 10 guides of each of the 3 types evaluated was measured once. Differences in reliability and accuracy were evaluated using the Standard Normal z test (2 sided) (alpha=.05) with Bonferroni correction. Reliability of devices was as follows: ShadeVision, 99.0%; SpectroShade, 96.9%; VITA Easyshade, 96.4%; and ShadeScan, 87.4%. A significant difference in reliability was found between ShadeVision and ShadeScan (P=.008). All other comparisons showed similar reliability. Accuracy of devices was as follows: VITA Easyshade, 92.6%; ShadeVision, 84.8%; SpectroShade, 80.2%; and ShadeScan, 66.8%. Significant differences in accuracy were found between all device pairs (P<.001) for all comparisons except for SpectroShade versus ShadeVision (P=.033). Most devices had similar high reliability (over 96%), indicating predictable shade values from repeated measurements. However, there was more variability in accuracy among devices (67-93%), and differences in accuracy were seen with most device comparisons.

Pathologic Markers Determining Prognosis in Patients with Treated or Healing Giant Cell Arteritis.

PubMed

Sultan, Harris; Smith, Stacy V; Lee, Andrew G; Chévez-Barrios, Patricia

2018-06-08

To provide quantitative evidence linking the Cluster of Differentiation-68 (CD68)+ macrophage-marker found on temporal artery biopsies (TABs) with disease prognosis. Retrospective, cross-sectional study METHODS: We examined 42 consecutive patients who had undergone unilateral TABs at a single hospital in 2015. Clinical data, laboratory data, and histopathologic features of TABs were recorded. clinical diagnosis of giant cell arteritis (GCA) with TAB performed at the same center. CD68 immunohistochemistry was used to label macrophages in the TABs. multiple logistic regression and bivariate comparisons to measure the association between CD68+ cells per histologic section with placement on immunomodulatory therapy (IMT). Twenty seven patients were females (64%), with a mean age of 72 (standard deviation [S.D.] ±7.7). Eleven patients (26%) were placed on IMT, 17 (40%) had disease recurrence during steroid taper, and 25 (60%) were referred to rheumatology. Of 42 biopsies, 35 underwent staining with CD68 to confirm active inflammation in suspicious, but not diagnostic, specimens. Patients eventually placed on IMT had increased CD68+ cells/slice compared to those not on IMT (median 5.00 [25-75 th quartile 2.00-7.15] vs 1.21 [0.38-2.57], p=0.031, respectively). A receiver operating characteristics (ROC) curve demonstrates that 2.17 CD68+ cells/slice predicts placement on IMT with an odds ratio of 1.54 (95% C.I. 1.02-2.33, p=0.038). Patients refractory to initial steroid tapers and those eventually placed on IMT had increased CD68 cells/section. CD68+ macrophages and their location on the internal elastic lamina may predict disease severity in patients with presumed GCA. Our results suggest that this marker may expedite patient triaging to alternate treatment to the usual steroid therapy. Copyright © 2018 Elsevier Inc. All rights reserved.

Tensiometry and dilational rheology of mixed β-lactoglobulin/ionic surfactant adsorption layers at water/air and water/hexane interfaces.

PubMed

Dan, Abhijit; Gochev, Georgi; Miller, Reinhard

2015-07-01

Oscillating drop tensiometry was applied to study adsorbed interfacial layers at water/air and water/hexane interfaces formed from mixed solutions of β-lactoglobulin (BLG, 1 μM in 10 mM buffer, pH 7 - negative net charge) and the anionic surfactant SDS or the cationic DoTAB. The interfacial pressure Π and the dilational viscoelasticity modulus |E| of the mixed layers were measured for mixtures of varying surfactant concentrations. The double capillary technique was employed which enables exchange of the protein solution in the drop bulk by surfactant solution (sequential adsorption) or by pure buffer (washing out). The first protocol allows probing the influence of the surfactant on a pre-adsorbed protein layer thus studying the protein/surfactant interactions at the interface. The second protocol gives access to the residual values of Π and |E| measured after the washing out procedure thus bringing information about the process of protein desorption. The DoTAB/BLG complexes exhibit higher surface activity and higher resistance to desorption in comparison with those for the SDS/BLG complexes due to hydrophobization via electrostatic binding of surfactant molecules. The neutral DoTAB/BLG complexes achieve maximum elastic response of the mixed layer. Mixed BLG/surfactant layers at the water/oil interface are found to reach higher surface pressure and lower maximum dilational elasticity than those at the water/air surface. The sequential adsorption mode experiments and the desorption study reveal that binding of DoTAB to pre-adsorbed BLG globules is somehow restricted at the water/air surface in comparison with the case of complex formation in the solution bulk and subsequently adsorbed at the water/air surface. Maximum elasticity is achieved with washed out layers obtained after simultaneous adsorption, i.e. isolation of the most surface active DoTAB/BLG complex. These specific effects are much less pronounced at the W/H interface. Copyright © 2015 Elsevier Inc. All rights reserved.

Evaluation of reliability and validity of three dental color-matching devices.

PubMed

Tsiliagkou, Aikaterini; Diamantopoulou, Sofia; Papazoglou, Efstratios; Kakaboura, Afrodite

2016-01-01

To assess the repeatability and accuracy of three dental color-matching devices under standardized and freehand measurement conditions. Two shade guides (Vita Classical A1-D4, Vita; and Vita Toothguide 3D-Master, Vita), and three color-matching devices (Easyshade, Vita; SpectroShade, MHT Optic Research; and ShadeVision, X-Rite) were used. Five shade tabs were selected from the Vita Classical A1-D4 (A2, A3.5, B1, C4, D3), and five from the Vita Toothguide 3D-Master (1M1, 2R1.5, 3M2, 4L2.5, 5M3) shade guides. Each shade tab was recorded 15 continuous, repeated times with each device under two different measurement conditions (standardized, and freehand). Both qualitative (color shade) and quantitative (L, a, and b) color characteristics were recorded. The color difference (ΔE) of each recorded value with the known values of the shade tab was calculated. The repeatability of each device was evaluated by the coefficient of variance. The accuracy of each device was determined by comparing the recorded values with the known values of the reference shade tab (one sample t test; α = 0.05). The agreement between the recorded shade and the reference shade tab was calculated. The influence of the parameters (devices and conditions) on the parameter ΔE was investigated (two-way ANOVA). Comparison of the devices was performed with Bonferroni pairwise post-hoc analysis. Under standardized conditions, repeatability of all three devices was very good, except for ShadeVision with Vita Classical A1-D4. Accuracy ranged from good to fair, depending on the device and the shade guide. Under freehand conditions, repeatability and accuracy for Easyshade and ShadeVision were negatively influenced, but not for SpectroShade, regardless of the shade guide. Based on the total of the color parameters assessed per device, SpectroShade was the most reliable of the three color-matching devices studied.

Towards a semantic medical Web: HealthCyberMap's tool for building an RDF metadata base of health information resources based on the Qualified Dublin Core Metadata Set.

PubMed

Boulos, Maged N; Roudsari, Abdul V; Carson, Ewart R

2002-07-01

HealthCyberMap (http://healthcybermap.semanticweb.org/) aims at mapping Internet health information resources in novel ways for enhanced retrieval and navigation. This is achieved by collecting appropriate resource metadata in an unambiguous form that preserves semantics. We modelled a qualified Dublin Core (DC) metadata set ontology with extra elements for resource quality and geographical provenance in Prot g -2000. A metadata collection form helps acquiring resource instance data within Prot g . The DC subject field is populated with UMLS terms directly imported from UMLS Knowledge Source Server using UMLS tab, a Prot g -2000 plug-in. The project is saved in RDFS/RDF. The ontology and associated form serve as a free tool for building and maintaining an RDF medical resource metadata base. The UMLS tab enables browsing and searching for concepts that best describe a resource, and importing them to DC subject fields. The resultant metadata base can be used with a search and inference engine, and have textual and/or visual navigation interface(s) applied to it, to ultimately build a medical Semantic Web portal. Different ways of exploiting Prot g -2000 RDF output are discussed. By making the context and semantics of resources, not merely their raw text and formatting, amenable to computer 'understanding,' we can build a Semantic Web that is more useful to humans than the current Web. This requires proper use of metadata and ontologies. Clinical codes can reliably describe the subjects of medical resources, establish the semantic relationships (as defined by underlying coding scheme) between related resources, and automate their topical categorisation.

Risk factors special to eastern culture for the development of anal fissure.

PubMed

Erel, Serap; Adahan, Didem; Kismet, Kemal; Caylan, Ayse; Tanrikulu, Yusuf; Akkus, Mehmet Ali

2009-01-01

To reveal the effect of diet, bowel functions and toilet habits on the development of anal fissure. One hundred patients complaining of anal fissure were included to the case group; and one hundred age- and gender-matched patients referred for other reasons except for anorectal complaints were included to the control group. The information was obtained by face to face interviews using questionnaires. Statistically significant differences were found in coffee, fruit, and meat consumption between the groups. The patients suffering from anal fissure avoided paprika consumption. The rate of anal fissure incidence was higher in squat toilet users. This study is the first study which evaluates the risk factors such as paprika consumption and squat toilet usage that are specific to Eastern culture. Further studies including large numbers of population are needed to evaluate different risk factors for anal fissure development (Tab. 2, Ref. 11). Full Text (Free, PDF) www.bmj.sk.

Hanford cultural resources management plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chatters, J.C.

1989-06-01

As a federal agency, the US Department of Energy (DOE) has been directed by Congress and the President to provide leadership in the preservation of prehistoric, historical, and cultural resources on lands it administers, to manage these in a spirit of stewardship for future generations, and to protect and preserve the rights of Native Americans to religious freedom. The purpose of this document is to describe how the DOE-Richland Operations (DOE-RL) will meet those responsibilities on the Hanford Site, pursuant to guidelines for Agency Responsibilities under the Historic Preservation Act (FR 53:31, February 17, 1988). This document is intended formore » multiple uses. Among other things, the text is designed as a manual for cultural resource managers to follow and as an explanation of the process of cultural resource regulatory compliance for the DOE-RL and Site contractors. 10 refs., 17 figs., 11 tabs.« less

DoD/VA Health Information Technology (IT) Data Sharing to Benefit Our Patients

DTIC Science & Technology

2011-01-25

drug·drug interaction: ERYTHROMYCIN!. SIMVASTATIN [SIMVASTATIN TAB 40MG 1--:====- 1/2 TABLET BY MOUTH EVERY EVENING FOR 90 DAYS ’ TO LOWER Patient lnsbuction...rv TAKEN LESTEROL’AVOID GRAPEFRUIT AND ITS JUICE’USE TABLET CUTTER change from 20 mg. [ACTIVEJ] drug·drug interaction: ERYTHROMYCIN!. SIMVASTATIN...SIMVASTATIN 20MG TAB ONE TABLET BY MOUTH EVERYDAY IN THE EVENING TO LOWER CHOLESTEROL II RF3[ACTIVEI » NH Great Lakes IL) I Accept Order I Cancel

Syllabus Design and Manner of Delivery Impacts on Content Memory and Impressions

DTIC Science & Technology

2015-05-15

for submission of article at Tab I to the Journal of Effective Teaching 2. BACKGROUND. Tab I : Authors: C IC Jasmine Leyro (soon to be 2L T) and Dr...So TL research project conducted by Jasmine Leyro and Dr. Scharff during Spring 2013 that investigated how targeted content location (beginning vs...and Impressions Jasmine G. Leyro Lauren V. Scharff U. S. Air Force Academy Author Note We recognize and thank David J. Heaphy for his

Ballistic Missile Defense Organization, Advance Planning Briefing for Industry, Updated Agenda, Attendance Roster, Proceedings.

DTIC Science & Technology

1994-03-01

DC 20007-2172 (202) 944-6434 x Mr. Dennis G. Evans Galaxy Scientific Corp. 4900 Seminary Rd Suite 400 Alexandria VA 22311-1860 (703) 379-2107 x...the Ranger Tab. General O’Neill and his wife, Judy, have two children, Bonnie and John. The general is a native of Chicago, El. (Current as of...with two Oak Leaf Clusters, the Army Commendation Medal with Oak Leaf Cluster, the Combat Infantryman Badge, the Ranger Tab, and the Army Staff

Human MicroRNA miR-532-5p Exhibits Antiviral Activity against West Nile Virus via Suppression of Host Genes SESTD1 and TAB3 Required for Virus Replication

PubMed Central

Slonchak, Andrii; Shannon, Rory P.; Pali, Gabor

2015-01-01

ABSTRACT West Nile virus (WNV) is a mosquito-transmitted flavivirus that naturally circulates between mosquitos and birds but can also infect humans, causing severe neurological disease. The early host response to WNV infection in vertebrates primarily relies on the type I interferon pathway; however, recent studies suggest that microRNAs (miRNAs) may also play a notable role. In this study, we assessed the role of host miRNAs in response to WNV infection in human cells. We employed small RNA sequencing (RNA-seq) analysis to determine changes in the expression of host miRNAs in HEK293 cells infected with an Australian strain of WNV, Kunjin (WNVKUN), and identified a number of host miRNAs differentially expressed in response to infection. Three of these miRNAs were confirmed to be significantly upregulated in infected cells by quantitative reverse transcription (qRT)-PCR and Northern blot analyses, and one of them, miR-532-5p, exhibited a significant antiviral effect against WNVKUN infection. We have demonstrated that miR-532-5p targets and downregulates expression of the host genes SESTD1 and TAB3 in human cells. Small interfering RNA (siRNA) depletion studies showed that both SESTD1 and TAB3 were required for efficient WNVKUN replication. We also demonstrated upregulation of mir-532-5p expression and a corresponding decrease in the expression of its targets, SESTD1 and TAB3, in the brains of WNVKUN -infected mice. Our results show that upregulation of miR-532-5p and subsequent suppression of the SESTD1 and TAB3 genes represent a host antiviral response aimed at limiting WNVKUN infection and highlight the important role of miRNAs in controlling RNA virus infections in mammalian hosts. IMPORTANCE West Nile virus (WNV) is a significant viral pathogen that poses a considerable threat to human health across the globe. There is no specific treatment or licensed vaccine available for WNV, and deeper insight into how the virus interacts with the host is required to facilitate their development. In this study, we addressed the role of host microRNAs (miRNAs) in antiviral response to WNV in human cells. We identified miR-532-5p as a novel antiviral miRNA and showed that it is upregulated in response to WNV infection and suppresses the expression of the host genes TAB3 and SESTD1 required for WNV replication. Our results show that upregulation of miR-532-5p and subsequent suppression of the SESTD1 and TAB3 genes represent an antiviral response aimed at limiting WNV infection and highlight the important role of miRNAs in controlling virus infections in mammalian hosts. PMID:26676784

KSC-04pd1337

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., look over a solar panel ready to be installed on NASA’s MESSENGER spacecraft. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1366

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) prepare one of two solar array panels on the MESSENGER spacecraft for deployment. The panels will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1347

NASA Image and Video Library

2004-06-25

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians secure guide wires on the second solar panel to be installed on NASA’s MESSENGER spacecraft. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1368

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., a technician with The Johns Hopkins University Applied Physics Laboratory (APL) watches as one of the solar array panels on the MESSENGER spacecraft is deployed. The two panels will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1339

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., carry a solar panel toward NASA’s MESSENGER spacecraft for installation. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1370

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) check one of two solar panels on the MESSENGER spacecraft after a deployment test. The other panel is at right, undeployed. The solar arrays will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1340

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., adjust a solar panel suspended from above for installation on NASA’s MESSENGER spacecraft. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1346

NASA Image and Video Library

2004-06-25

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians check the second solar panel that will be installed on NASA’s MESSENGER spacecraft. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1345

NASA Image and Video Library

2004-06-25

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians maneuver a second solar panel to a vertical position to move it toward NASA’s MESSENGER spacecraft for installation. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1367

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) prepare one of two solar array panels on the MESSENGER spacecraft for deployment. The panels will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1341

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., maneuver a solar panel into place for installation on NASA’s MESSENGER spacecraft. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1344

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., help guide a solar panel toward NASA’s MESSENGER spacecraft for installation. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1349

NASA Image and Video Library

2004-06-25

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., hold steady the second solar panel being installed on NASA’s MESSENGER spacecraft. At left is the first panel already installed. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1343

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., guide a solar panel closer to NASA’s MESSENGER spacecraft for installation. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1338

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., attach a bar to a solar panel in order to lift it and move it to NASA’s MESSENGER spacecraft for installation. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

KSC-04pd1342

NASA Image and Video Library

2004-06-24

KENNEDY SPACE CENTER, FLA. - Technicians at Astrotech in Titusville, Fla., steady a solar panel suspended from above as others prepare to install it on NASA’s MESSENGER spacecraft. It is one of two large solar panels, supplemented with a nickel-hydrogen battery, that will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

Detection of cyst using image segmentation and building knowledge-based intelligent decision support system as an aid to telemedicine

NASA Astrophysics Data System (ADS)

Janet, J.; Natesan, T. R.; Santhosh, Ramamurthy; Ibramsha, Mohideen

2005-02-01

An intelligent decision support tool to the Radiologist in telemedicine is described. Medical prescriptions are given based on the images of cyst that has been transmitted over computer networks to the remote medical center. The digital image, acquired by sonography, is converted into an intensity image. This image is then subjected to image preprocessing which involves correction methods to eliminate specific artifacts. The image is resized into a 256 x 256 matrix by using bilinear interpolation method. The background area is detected using distinct block operation. The area of the cyst is calculated by removing the background area from the original image. Boundary enhancement and morphological operations are done to remove unrelated pixels. This gives us the cyst volume. This segmented image of the cyst is sent to the remote medical center for analysis by Knowledge based artificial Intelligent Decision Support System (KIDSS). The type of cyst is detected and reported to the control mechanism of KIDSS. Then the inference engine compares this with the knowledge base and gives appropriate medical prescriptions or treatment recommendations by applying reasoning mechanisms at the remote medical center.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Hyung Chul; Wallington, Timothy J.

Assessing the life-cycle benefits of vehicle lightweighting requires a quantitative description of mass-induced fuel consumption (MIF) and fuel reduction values (FRVs). We have extended our physics-based model of MIF and FRVs for internal combustion engine vehicles (ICEVs) to electrified vehicles (EVs) including hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs). We illustrate the utility of the model by calculating MIFs and FRVs for 37 EVs and 13 ICEVs. BEVs have much smaller MIF and FRVs, both in the range 0.04-0.07 L e/(100 km 100 kg), than those for ICEVs which are in the rangesmore » 0.19-0.32 and 0.16-0.22 L/(100 km 100 kg), respectively. The MIF and FRVs for HEVs and PHEVs mostly lie between those for ICEVs and BEVs. Powertrain resizing increases the FRVs for ICEVs, HEVs and PHEVs. Lightweighting EVs is less effective in reducing greenhouse gas emissions than lightweighting ICEVs, however the benefits differ substantially for different vehicle models. The physics-based approach outlined here enables model specific assessments for ICEVs, HEVs, PHEVs, and BEVs required to determine the optimal strategy for maximizing the life-cycle benefits of lightweighting the light-duty vehicle fleet.« less

Flexible Wing Model for Structural Sizing and Multidisciplinary Design Optimization of a Strut-Braced Wing

NASA Technical Reports Server (NTRS)

Gern, Frank H.; Naghshineh, Amir H.; Sulaeman, Erwin; Kapania, Rakesh K.; Haftka, Raphael T.

2000-01-01

This paper describes a structural and aeroelastic model for wing sizing and weight calculation of a strut-braced wing. The wing weight is calculated using a newly developed structural weight analysis module considering the special nature of strut-braced wings. A specially developed aeroelastic model enables one to consider wing flexibility and spanload redistribution during in-flight maneuvers. The structural model uses a hexagonal wing-box featuring skin panels, stringers, and spar caps, whereas the aerodynamics part employs a linearized transonic vortex lattice method. Thus, the wing weight may be calculated from the rigid or flexible wing spanload. The calculations reveal the significant influence of the strut on the bending material weight of the wing. The use of a strut enables one to design a wing with thin airfoils without weight penalty. The strut also influences wing spanload and deformations. Weight savings are not only possible by calculation and iterative resizing of the wing structure according to the actual design loads. Moreover, as an advantage over the cantilever wing, employment of the strut twist moment for further load alleviation leads to increased savings in structural weight.

The influence of sulcus width on simulated electric fields induced by transcranial magnetic stimulation

PubMed Central

Janssen, A M; Rampersad, S M; Lucka, F; Lanfer, B; Lew, S; Aydin, Ü; Wolters, C H; Stegeman, D F; Oostendorp, T F

2013-01-01

Volume conduction models can help in acquiring knowledge about the distribution of the electric field induced by transcranial magnetic stimulation (TMS). One aspect of a detailed model is an accurate description of the cortical surface geometry. Since its estimation is difficult, it is important to know how accurate the geometry has to be represented. Previous studies only looked at the differences caused by neglecting the complete boundary between the CSF and GM (Thielscher et al. 2011; Bijsterbosch et al. 2012), or by resizing the whole brain (Wagner et al. 2008). However, due to the high conductive properties of the CSF, it can be expected that alterations in sulcus width can already have a significant effect on the distribution of the electric field. To answer this question, the sulcus width of a highly realistic head model, based on T1-, T2- and diffusion-weighted magnetic resonance images (MRI), was altered systematically. This study shows that alterations in the sulcus width do not cause large differences in the majority of the electric field values. However, considerable overestimation of sulcus width produces an overestimation of the calculated field strength, also at locations distant from the target location. PMID:23787706

KSC-04pd1373

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) prepare to cover the MESSESNGER spacecraft for a move to a hazardous processing facility in preparation for loading the spacecraft’s complement of hypergolic propellants. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla., on a journey to Mercury. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1372

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) prepare the MESSESNGER spacecraft for a move to a hazardous processing facility in preparation for loading the spacecraft’s complement of hypergolic propellants. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla., on a journey to Mercury. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1369

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) monitor the progress of the solar array deployment on the MESSENGER spacecraft. The two panels will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

Integration of low level and ontology derived features for automatic weapon recognition and identification

NASA Astrophysics Data System (ADS)

Sirakov, Nikolay M.; Suh, Sang; Attardo, Salvatore

2011-06-01

This paper presents a further step of a research toward the development of a quick and accurate weapons identification methodology and system. A basic stage of this methodology is the automatic acquisition and updating of weapons ontology as a source of deriving high level weapons information. The present paper outlines the main ideas used to approach the goal. In the next stage, a clustering approach is suggested on the base of hierarchy of concepts. An inherent slot of every node of the proposed ontology is a low level features vector (LLFV), which facilitates the search through the ontology. Part of the LLFV is the information about the object's parts. To partition an object a new approach is presented capable of defining the objects concavities used to mark the end points of weapon parts, considered as convexities. Further an existing matching approach is optimized to determine whether an ontological object matches the objects from an input image. Objects from derived ontological clusters will be considered for the matching process. Image resizing is studied and applied to decrease the runtime of the matching approach and investigate its rotational and scaling invariance. Set of experiments are preformed to validate the theoretical concepts.

NASA Earth Observations (NEO): Data Imagery for Education and Visualization

NASA Astrophysics Data System (ADS)

Ward, K.

2008-12-01

NASA Earth Observations (NEO) has dramatically simplified public access to georeferenced imagery of NASA remote sensing data. NEO targets the non-traditional data users who are currently underserved by functionality and formats available from the existing data ordering systems. These users include formal and informal educators, museum and science center personnel, professional communicators, and citizen scientists. NEO currently serves imagery from 45 different datasets with daily, weekly, and/or monthly temporal resolutions, with more datasets currently under development. The imagery from these datasets is produced in coordination with several data partners who are affiliated either with the instrument science teams or with the respective data processing center. NEO is a system of three components -- website, WMS (Web Mapping Service), and ftp archive -- which together are able to meet the wide-ranging needs of our users. Some of these needs include the ability to: view and manipulate imagery using the NEO website -- e.g., applying color palettes, resizing, exporting to a variety of formats including PNG, JPEG, KMZ (Google Earth), GeoTIFF; access the NEO collection via a standards-based API (WMS); and create customized exports for select users (ftp archive) such as Science on a Sphere, NASA's Earth Observatory, and others.

Optimal Filter Estimation for Lucas-Kanade Optical Flow

PubMed Central

Sharmin, Nusrat; Brad, Remus

2012-01-01

Optical flow algorithms offer a way to estimate motion from a sequence of images. The computation of optical flow plays a key-role in several computer vision applications, including motion detection and segmentation, frame interpolation, three-dimensional scene reconstruction, robot navigation and video compression. In the case of gradient based optical flow implementation, the pre-filtering step plays a vital role, not only for accurate computation of optical flow, but also for the improvement of performance. Generally, in optical flow computation, filtering is used at the initial level on original input images and afterwards, the images are resized. In this paper, we propose an image filtering approach as a pre-processing step for the Lucas-Kanade pyramidal optical flow algorithm. Based on a study of different types of filtering methods and applied on the Iterative Refined Lucas-Kanade, we have concluded on the best filtering practice. As the Gaussian smoothing filter was selected, an empirical approach for the Gaussian variance estimation was introduced. Tested on the Middlebury image sequences, a correlation between the image intensity value and the standard deviation value of the Gaussian function was established. Finally, we have found that our selection method offers a better performance for the Lucas-Kanade optical flow algorithm.

Automatic Detection of Acromegaly From Facial Photographs Using Machine Learning Methods.

PubMed

Kong, Xiangyi; Gong, Shun; Su, Lijuan; Howard, Newton; Kong, Yanguo

2018-01-01

Automatic early detection of acromegaly is theoretically possible from facial photographs, which can lessen the prevalence and increase the cure probability. In this study, several popular machine learning algorithms were used to train a retrospective development dataset consisting of 527 acromegaly patients and 596 normal subjects. We firstly used OpenCV to detect the face bounding rectangle box, and then cropped and resized it to the same pixel dimensions. From the detected faces, locations of facial landmarks which were the potential clinical indicators were extracted. Frontalization was then adopted to synthesize frontal facing views to improve the performance. Several popular machine learning methods including LM, KNN, SVM, RT, CNN, and EM were used to automatically identify acromegaly from the detected facial photographs, extracted facial landmarks, and synthesized frontal faces. The trained models were evaluated using a separate dataset, of which half were diagnosed as acromegaly by growth hormone suppression test. The best result of our proposed methods showed a PPV of 96%, a NPV of 95%, a sensitivity of 96% and a specificity of 96%. Artificial intelligence can automatically early detect acromegaly with a high sensitivity and specificity. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Image re-sampling detection through a novel interpolation kernel.

PubMed

Hilal, Alaa

2018-06-01

Image re-sampling involved in re-size and rotation transformations is an essential element block in a typical digital image alteration. Fortunately, traces left from such processes are detectable, proving that the image has gone a re-sampling transformation. Within this context, we present in this paper two original contributions. First, we propose a new re-sampling interpolation kernel. It depends on five independent parameters that controls its amplitude, angular frequency, standard deviation, and duration. Then, we demonstrate its capacity to imitate the same behavior of the most frequent interpolation kernels used in digital image re-sampling applications. Secondly, the proposed model is used to characterize and detect the correlation coefficients involved in re-sampling transformations. The involved process includes a minimization of an error function using the gradient method. The proposed method is assessed over a large database of 11,000 re-sampled images. Additionally, it is implemented within an algorithm in order to assess images that had undergone complex transformations. Obtained results demonstrate better performance and reduced processing time when compared to a reference method validating the suitability of the proposed approaches. Copyright © 2018 Elsevier B.V. All rights reserved.

Design of a powered elevator control system. [powered elevator system for modified C-8A aircraft for STOL operation

NASA Technical Reports Server (NTRS)

Glende, W. L. B.

1974-01-01

The design, fabrication and flight testing of a powered elevator system for the Augmentor Wing Jet STOL Research Aircraft (AWJSRA or Mod C-8A) are discussed. The system replaces a manual spring tab elevator control system that was unsatisfactory in the STOL flight regime. Pitch control in the AWJSRA is by means of a single elevator control surface. The elevator is used for both maneuver and trim control as the stabilizer is fixed. A fully powered, irreversible flight control system powered by dual hydraulic sources was designed. The existing control columns and single mechanical cable system of the AWJSRA have been retained as has been the basic elevator surface, except that the elevator spring tab is modified into a geared balance tab. The control surface is directly actuated by a dual tandem moving body actuator. Control signals are transmitted from the elevator aft quadrant to the actuator by a linkage system that includes a limited authority series servo actuator.

Skin permeation and retention of topical bead formulation containing tranexamic acid.

PubMed

Vijayakumar, Ajay; Baskaran, Rengarajan; Yoo, Bong Kyu

2017-02-01

The objective of this study is to develop a topical bead formulation of tranexamic acid (TA) which can be used concomitantly with laser treatment. The bead formulation of TA (TAB) was successfully prepared by fluidized bed drying method. Physicochemical properties of the TAB were evaluated in terms of chemical stability of TA and differential scanning calorimetry. TA in the bead was stable up to six months at 25°C and existed as amorphous state. In vitro skin permeation and in vivo skin retention of TA in the beads were significantly higher compared to a commercial product. When the bead was dissolved into distilled water and applied concomitantly with laser treatment, the amount of TA retained in the skin in the in vivo study was inversely proportional to the energy levels of laser treatment, indicating absorption into subcutaneous tissue and drainage to systemic circulation. Therefore, when laser treatment is used concomitantly with TAB, energy level should be very carefully monitored to avoid possible adverse events associated with systemic side effects of TA.

Modeling of Turbulence Effects on Liquid Jet Atomization and Breakup

NASA Technical Reports Server (NTRS)

Trinh, Huu P.; Chen, C. P.

2005-01-01

Recent experimental investigations and physical modeling studies have indicated that turbulence behaviors within a liquid jet have considerable effects on the atomization process. This study aims to model the turbulence effect in the atomization process of a cylindrical liquid jet. Two widely used models, the Kelvin-Helmholtz (KH) instability of Reitz (blob model) and the Taylor-Analogy-Breakup (TAB) secondary droplet breakup by O Rourke et al, are further extended to include turbulence effects. In the primary breakup model, the level of the turbulence effect on the liquid breakup depends on the characteristic scales and the initial flow conditions. For the secondary breakup, an additional turbulence force acted on parent drops is modeled and integrated into the TAB governing equation. The drop size formed from this breakup regime is estimated based on the energy balance before and after the breakup occurrence. This paper describes theoretical development of the current models, called "T-blob" and "T-TAB", for primary and secondary breakup respectivety. Several assessment studies are also presented in this paper.

Density Fluctuation in Asymmetric Nozzle Plumes and Correlation with Far Field Noise

NASA Technical Reports Server (NTRS)

Panda, J.; Zaman, K. B. M. Q.

2001-01-01

A comparative experimental study of air density fluctuations in the unheated plumes of a circular, 4-tabbed-circular, chevron-circular and 10-lobed rectangular nozzles was performed at a fixed Mach number of 0.95 using a recently developed Rayleigh scattering based technique. Subsequently, the flow density fluctuations are cross-correlated with the far field sound pressure fluctuations to determine sources for acoustics emission. The nearly identical noise spectra from the baseline circular and the chevron nozzles are found to be in agreement with the similarity in spreading, turbulence fluctuations, and flow-sound correlations measured in the plumes. The lobed nozzle produced the least low frequency noise, in agreement with the weakest overall density fluctuations and flow-sound correlation. The tabbed nozzle took an intermediate position in the hierarchy of noise generation, intensity of turbulent fluctuation and flow-sound correlation. Some of the features in the 4-tabbed nozzle are found to be explainable in terms of splitting of the jet in a central large core and 4 side jetlets.

Manually Operated Welding Wire Feeder

NASA Technical Reports Server (NTRS)

Rybicki, Daniel J. (Inventor)

2001-01-01

A manual welding wire feeder apparatus comprising a bendable elongate metal frame with a feed roller mounted at the center thereof for rotation about an axis transverse to the longitudinal axis of the frame. The frame ends are turned up as tabs and each provided with openings in alignment with each other and the mid-width center of the roller surface. The tab openings are sized to accommodate welding wire and each extends to a side edge of the tab, both opening on the same side of the frame, whereby welding wire can be side-loaded onto the frame. On the side of the frame, opposite the roller a lock ring handle is attached tangentially and is rotatable about the attachment point and an axis perpendicular to the frame. The device is grasped in the hand normally used to hold the wire. A finger is placed through the loop ring and the frame positioned across the palm and lower fingers. The thumb is positioned atop the wire so it can be moved from the back of the frame across the roller, and towards the front. In doing so, the wire is advanced at a steady rate in axial alignment with the tab openings and roller. To accommodate different wire diameters the frame is bendable about its center in the plane of the frame axis and wire so as to keep the wire in sufficient tension against the roller and to keep the wire fixed when the frame is tilted and thumb pressure released.

GIDEP Batching Tool

NASA Technical Reports Server (NTRS)

Fong, Danny; Odell,Dorice; Barry, Peter; Abrahamian, Tomik

2008-01-01

This software provides internal, automated search mechanics of GIDEP (Government- Industry Data Exchange Program) Alert data imported from the GIDEP government Web site. The batching tool allows the import of a single parts list in tab-delimited text format into the local JPL GIDEP database. Delimiters from every part number are removed. The original part numbers with delimiters are compared, as well as the newly generated list without the delimiters. The two lists run against the GIDEP imports, and output any matches. This feature only works with Netscape 2.0 or greater, or Internet Explorer 4.0 or greater. The user selects the browser button to choose a text file to import. When the submit button is pressed, this script will import alerts from the text file into the local JPL GIDEP database. This batch tool provides complete in-house control over exported material and data for automated batch match abilities. The batching tool has the ability to match capabilities of the parts list to tables, and yields results that aid further research and analysis. This provides more control over GIDEP information for metrics and reports information not provided by the government site. This software yields results quickly and gives more control over external data from the government site in order to generate other reports not available from the external source. There is enough space to store years of data. The program relates to risk identification and management with regard to projects and GIDEP alert information encompassing flight parts for space exploration.

[Evaluation of occupational risk factors, nutritional habits and nutritional status in industrial workers].

PubMed

Domagała-Dobrzycka, M

2000-01-01

The objective of this study was to examine the relationship between selected risk factors at the workplace and health indices in relation to nutritional habits and nutritional status in industrial workers. Exposure to physical and chemical risk factors and their impact on health in the province of Szczecin and in Poland was evaluated basing on data published in the Yearbooks of the Province of Szczecin, the Central Statistics Bureau (GUS) and Regional Inspectorate of Labor (OIP) in Szczecin. A random selection of plants in Szczecin was done and workplaces with chemical and physical risk levels exceeding the highest acceptable values were identified. Measurements of concentrations of chemicals and intensity of physical factors were performed by Work Environment Research Laboratories of the plants and by the laboratory of the Sanitary and Epidemiological Center in Szczecin. Eighty-eight men exposed to occupational risk factors were randomly selected. The mean period of exposure in that group was approximately ten years. The control group was composed of male workers (n = 83) not exposed to any of the risk factors in question (Tab. 3). Nutritional habits and nutritional status were studied during summer/autumn and winter/spring periods. Dietary survey consisted of the last 24-hour nutrient intake questionnaire. Nutritional status evaluation was based on body mass index (BMI) values and results of the following laboratory tests: blood cell count, levels of total protein, prealbumin, retinol binding protein (RBP), magnesium, inorganic phosphorus, and ascorbic acid. The following results were obtained: 1. Physical factors constituted the most frequent source of occupational risk in the province of Szczecin and in Poland in 1990-1994 (Tab. 1); 2. The incidence of occupational risk and occupational disease morbidity rates in 1990-1994 were lower for the province of Szczecin than the average for Poland; 3. The rate of fatal accidents at work in 1982-1994 was higher for the province of Szczecin than the average for Poland (Tab. 2); 4. Differences in dietary habits between the study and control groups were not statistically significant; 5. Statistically significant differences as to levels of prealbumin (Tab. 6), inorganic phosphorus (Tab. 7) and ascorbic acid (Tab. 8) between the study and control groups were found. In conclusion, conditions at the workplace should be improved, efforts to reduce exposure to physical and chemical risk factors should be intensified, and a healthy lifestyle should be promoted among industrial workers.

Altimeter Processing Tools for Analyzing Mesoscale Ocean Features

DTIC Science & Technology

1990-09-01

However, since the programs are modular, users can easily use their own orbit and geoid corrections to study basin scale problems. We left programs that...g..repeat c*/c*.a002c > a002cs-m or %g.repeat c???/c???.a002c > a002cs-m The file aOO2cs.m contains the following information in tab delimited ...information in tab delimited columns: The sea surface height residual files are similar to those created by g.repeat. except that fi(z ,t) is the original

Effect of Strain Rates and Pre-Twist on Tensile Strength of Kevlar KM2 Single Fiber

DTIC Science & Technology

2013-04-01

cardboard tabs at a standard gage length of 5.2 mm for testing using 3M DP8005 epoxy . The cardboard tabs were glued to stainless steel setscrews so that...did not pull out of the glue . If pullout were evident, the force would rise followed by a flat portion where the fiber takes a small amount of load...until the fiber comes back into contact with the glue followed by another rise and so on until failure. Figure 5. Raw data from a high-rate

Characteristics of a Sealed Internally Balanced Aileron from Tests of a 1/4-Scale Partial-Span Model of the Republic XF-12 Airplane in the Langley 19-Foot Pressure Tunnel

NASA Technical Reports Server (NTRS)

Graham, Robert R.; Martina, Albert P.; Salmi, Reino J.

1946-01-01

This paper presents the results of the aileron investigation and includes rolling-moment, yawing-moment, and aileron hinge-moment coefficients and pressure coefficients across the aileron-balance seal through a range of angle of attack, tab deflection, and aileron deflection with flaps neutral and deflected 20 degrees and 55 degrees. Some of the effects of wing roughness and balance seal leakage on the aileron and tab characteristics are also presented.

Simplified Flutter Prevention Criteria for Personal Type Aircraft

DTIC Science & Technology

1955-01-01

Play of Ailerons The total free play at the aileron edge of each aileron, when the other aileron is cla:nped to the wing should not exceed 2.5 percent of...the aileron chcrd aft of the hinge line at the station where the free play is measured. Elevator Balance Each elevator should be dynamically balanced...8217•. • . e •% f% ’dr-,•~~ • . S•, ,,,8- 2. The total free play at the tab trailing edge should be less than 2.5% of the tab chord aft of the hinge

Quick Reaction Evaluation of Materials and Processes. Delivery Order 0011: Engineering Properties, Fatigue, and Crack Growth Data on SCS-6/Ti-6Al-4V Titanium Matrix Composite (16 Ply) Panels

DTIC Science & Technology

2009-05-01

tabs were bonded to the specimen using a TIG welding process to ensure adhesion of the tabs throughout the experiment. The shear specimens and the...AFRL-RX-WP-TR-2010-4175 QUICK REACTION EVALUATION OF MATERIALS AND PROCESSES Delivery Order 0011: Engineering Properties, Fatigue, and Crack...From - To) May 2009 Final 03 April 2006 – 29 May 2009 4. TITLE AND SUBTITLE QUICK REACTION EVALUATION OF MATERIALS AND PROCESSES Delivery Order

Status of wraparound contact solar cells and arrays

NASA Technical Reports Server (NTRS)

Baraona, C. R.; Young, L. E.

1978-01-01

Solar cells with wraparound contacts provide the following advantages in array assembly: (1) eliminate the need for discretely formed, damage susceptible series tabs; (2) eliminate the n gap problem by allowing the use of uniform covers over the entire cell surface; (3) allow a higher packing factor by reducing the additional series spacing formly required for forming, and routing the series tab; and (4) allow the cell bonding to the interconnect system to be a single-side function wherein series contacts can be made at the same time parallel contracts are made.

Texas Automated Buoy System 1995-2005 and Beyond

NASA Astrophysics Data System (ADS)

Guinasso, N. L.; Bender, L. C.; Walpert, J. N.; Lee, L. L.; Campbell, L.; Hetland, R. D.; Howard, M. K.; Martin, R. D.

2005-05-01

TABS was established in l995 to provide data to assess oil spill movement along Texas coast for the Texas General Land Office Oil Spill Prevention and Response Program. A system of nine automated buoys provide wind and current data in near real time. Two of these buoys are supported by the Flower Garden Banks Joint Industry Program. A TABS web site provides a public interface to view and download the data. A real time data analysis web page presents a wide variety of useful data products derived from the field measurements. Integration efforts now underway include transfer of buoy data to the National Data Buoy Center for quality control and incorporation into the Global Telecommunications Stream. The TGLO ocean circulation nowcast/forecast modeling system has been in continuous operation since 1998. Two models, POM and ROMS, are used to produce forecasts of near-surface wind driven currents up to 48 hours into the future. Both models are driven using wind fields obtained from the NAM (formerly Eta) forecast models operated by NOAA NCEP. Wind and current fields are displayed on websites in both static and animated forms and are updated four times per day. Under funding from the SURA/SCOOP program we are; 1) revamping the system to conform with the evolving Data Management and Communications (DMAC) framework adopted by the NSF Orion and OCEAN.US IOOS programs, 2) producing model-data comparisons, and 3) integrating the wind and current fields into the GNOME oil trajectory model used by NOAA/Hazmat. Academic research is planned to assimilate near real-time observations from TABS buoys and some 30-40 ADCP instruments scheduled to be mounted on offshore oil platforms in early 2005. Texas Automated Buoy System (TABS) and its associated modeling efforts provide a reliable source of accurate, up-to-date information on currents along the Texas coast. As the nation embarks on the development of an Integrated Ocean Observing System (IOOS), TABS will be an active participant as a foundational regional component to the national backbone of ocean observations.

Evaluating the accuracy of tooth color measurement by combining the Munsell color system and dental colorimeter.

PubMed

Chang, Jiun-Yao; Chen, Wen-Cheng; Huang, Ta-Ko; Wang, Jen-Chyan; Fu, Po-Sung; Chen, Jeng-Huey; Hung, Chun-Cheng

2012-09-01

As we pay increasing attention to dental aesthetics, tooth color matching has become an important part of daily dental practice. This aim of this study was to develop a method to enhance the accuracy of a tooth color matching machine. The Munsell color tabs in the range of natural human teeth were measured using a tooth color measuring machine (ShadeEye NCC). The machine's accuracy was analyzed using an analysis of variance test and a Tukey post-hoc test. When matching the Munsell color tabs with the ShadeEye NCC colorimeter, settings of Chroma greater than 6 and Value less than 4 showed unacceptable clinical results. When the CIELAB mode was used, the a* value (which represents the red-green axis in the Commission Internationale de l'Eclairage color space) made no significant difference (p=0.84), the L* value (which represents the lightness) resulted in a negative correlation, and the b* value (which represents the yellow-blue axis) resulted in a positive correlation with ΔE. When the Munsell color tabs and the Vitapan were measured in the same mode and compared, the inaccuracies showed that the Vitapan was not a proper tool for evaluating the stability and accuracy of ShadeEye NCC. By knowing the limitations of the machine, we evaluated the data using the Munsell color tabs; shade beyond the acceptable range should be reevaluated using a visual shade matching method, or if measured by another machine, this shade range should be covered to obtain more accurate results. Copyright © 2012. Published by Elsevier B.V.

Adjustable mounting device for high-volume production of beam-shaping systems for high-power diode lasers

NASA Astrophysics Data System (ADS)

Haag, Sebastian; Bernhardt, Henning; Rübenach, Olaf; Haverkamp, Tobias; Müller, Tobias; Zontar, Daniel; Brecher, Christian

2015-02-01

In many applications for high-power diode lasers, the production of beam-shaping and homogenizing optical systems experience rising volumes and dynamical market demands. The automation of assembly processes on flexible and reconfigurable machines can contribute to a more responsive and scalable production. The paper presents a flexible mounting device designed for the challenging assembly of side-tab based optical systems. It provides design elements for precisely referencing and fixating two optical elements in a well-defined geometric relation. Side tabs are presented to the machine allowing the application of glue and a rotating mechanism allows the attachment to the optical elements. The device can be adjusted to fit different form factors and it can be used in high-volume assembly machines. The paper shows the utilization of the device for a collimation module consisting of a fast-axis and a slow-axis collimation lens. Results regarding the repeatability and process capability of bonding side tab assemblies as well as estimates from 3D simulation for overall performance indicators achieved such as cycle time and throughput will be discussed.

Supersonic Aerodynamic Characteristics of Proposed Mars '07 Smart Lander Configurations

NASA Technical Reports Server (NTRS)

Murphy, Kelly J.; Horvath, Thomas J.; Erickson, Gary E.; Green, Joseph M.

2002-01-01

Supersonic aerodynamic data were obtained for proposed Mars '07 Smart Lander configurations in NASA Langley Research Center's Unitary Plan Wind Tunnel. The primary objective of this test program was to assess the supersonic aerodynamic characteristics of the baseline Smart Lander configuration with and without fixed shelf/tab control surfaces. Data were obtained over a Mach number range of 2.3 to 4.5, at a free stream Reynolds Number of 1 x 10(exp 6) based on body diameter. All configurations were run at angles of attack from -5 to 20 degrees and angles of sideslip of -5 to 5 degrees. These results were complemented with computational fluid dynamic (CFD) predictions to enhance the understanding of experimentally observed aerodynamic trends. Inviscid and viscous full model CFD solutions compared well with experimental results for the baseline and 3 shelf/tab configurations. Over the range tested, Mach number effects were shown to be small on vehicle aerodynamic characteristics. Based on the results from 3 different shelf/tab configurations, a fixed control surface appears to be a feasible concept for meeting aerodynamic performance metrics necessary to satisfy mission requirements.

Dental Shade Guide Variability for Hues B, C, and D Using Cross-Polarized Photography.

PubMed

Sampaio, Camila S; Gurrea, Jon; Gurrea, Marta; Bruguera, August; Atria, Pablo J; Janal, Malvin; Bonfante, Estevam A; Coelho, Paulo G; Hirata, Ronaldo

2018-04-20

This study evaluated the color variability of hues B, C, and D between the VITA Classical shade guide (Vita Zahnfabrik) and four other VITA-coded ceramic shade guides using a digital camera (Canon EOS 60D) and computer software (Adobe Photoshop CC). A cross-polarizing filter was used to standardize external light sources influencing color match. A total of 275 pictures were taken, 5 per shade tab, for 11 shades (B1, B2, B3, B4, C1, C2, C3, C4, D2, D3, and D4), from the following shade guides: VITA Classical (control); IPS e.max Ceram (Ivoclar Vivadent); IPS d.SIGN (Ivoclar Vivadent); Initial ZI (GC); and Creation CC (Creation Willi Geller). Pictures were evaluated using Adobe Photoshop CC for standardization of hue, chroma, and value between shade tabs. The VITA-coded shade guides evaluated here showed an overall unmatched shade in all their tabs when compared to the control, suggesting that shade selection should be made with the corresponding manufacturer guide of the ceramic intended for the final restoration.

Effect of Oscillating Tabs on a Jet-in-Cross-Flow

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

2003-01-01

A novel technique for active control of a jet-in-cross-flow is explored in this study. Two triangular tabs are placed at the 90 degree and 270 degree edges of the jet orifice, relative to the direction of the cross-flow. A slight asymmetry in the placement of the two tabs is reversed periodically. This causes a profound oscillation of the flow field that persists as far downstream as the measurements were permitted by the facility (100 orifice diameters). Parametric dependence of the unsteadiness and its impact on the flowfield has been investigated preliminarily. It is found that the effect becomes increasingly pronounced with increasing value of the momentum flux ratio (J). However, there is little or no effect at low values of J in the range, J less than 15. The effective frequencies of oscillation are low - more than an order of magnitude lower than that found with oscillatory blowing technique in previous studies. The flow mechanism apparently involves a direct perturbation of the counter-rotating streamwise vortex pair of the flow.

Improving cylinder-type LiFePO4 battery performance via control of internal resistance

NASA Astrophysics Data System (ADS)

Purwanto, Agus; Jumari, Arif; Nizam, Muhammad; Widiyandari, Hendri; Sudaryanto; Deswita; Azmin Mohamad, Ahmad

2018-04-01

Strategies for controlling the internal resistance to improve battery performance were systematically investigated. Electrode densification of LiFePO4 cathodes significantly reduced the internal resistance of the prepared batteries. Densification by reduction to 31.25% of initial thickness resulted in optimal electrochemical performance of the prepared LiFePO4 batteries. The addition of KS 6 graphite material improved the conductivity of the cathodes, which was indicated by a lowering of the internal resistance. The internal resistance was decreased from 73 to 54 when the KS6/AB ratio was varied from 3 to 1. Another factor in controlling the internal resistance was the location of a welded aluminum tab in the cathode. The welding of an aluminum tab in a small gap in the cathode significantly reduced the internal resistance. Thus, three main factors can be performed during fabrication to reduce the internal resistance of a LiFePO4 battery: cathode densification, KS-6 graphite addition, and the arrangement of an aluminum tab welded to the cathode. By optimizing these factors, high-performance LFP batteries were produced.

A role for NRAGE in NF-κB activation through the non-canonical BMP pathway

PubMed Central

2010-01-01

Background Previous studies have linked neurotrophin receptor-interacting MAGE protein to the bone morphogenic protein signaling pathway and its effect on p38 mediated apoptosis of neural progenitor cells via the XIAP-Tak1-Tab1 complex. Its effect on NF-κB has yet to be explored. Results Herein we report that NRAGE, via the same XIAP-Tak1-Tab1 complex, is required for the phosphorylation of IKK -α/β and subsequent transcriptional activation of the p65 subunit of NF-κB. Ablation of endogenous NRAGE by siRNA inhibited NF-κB pathway activation, while ablation of Tak1 and Tab1 by morpholino inhibited overexpression of NRAGE from activating NF-κB. Finally, cytokine profiling of an NRAGE over-expressing stable line revealed the expression of macrophage migration inhibitory factor. Conclusion Modulation of NRAGE expression revealed novel roles in regulating NF-κB activity in the non-canonical bone morphogenic protein signaling pathway. The expression of macrophage migration inhibitory factor by bone morphogenic protein -4 reveals novel crosstalk between an immune cytokine and a developmental pathway. PMID:20100315

Automated solar module assembly line

NASA Technical Reports Server (NTRS)

Bycer, M.

1980-01-01

The solar module assembly machine which Kulicke and Soffa delivered under this contract is a cell tabbing and stringing machine, and capable of handling a variety of cells and assembling strings up to 4 feet long which then can be placed into a module array up to 2 feet by 4 feet in a series of parallel arrangement, and in a straight or interdigitated array format. The machine cycle is 5 seconds per solar cell. This machine is primarily adapted to 3 inch diameter round cells with two tabs between cells. Pulsed heat is used as the bond technique for solar cell interconnects. The solar module assembly machine unloads solar cells from a cassette, automatically orients them, applies flux and solders interconnect ribbons onto the cells. It then inverts the tabbed cells, connects them into cell strings, and delivers them into a module array format using a track mounted vacuum lance, from which they are taken to test and cleaning benches prior to final encapsulation into finished solar modules. Throughout the machine the solar cell is handled very carefully, and any contact with the collector side of the cell is avoided or minimized.

Method and design for externally applied laser welding of internal connections in a high power electrochemical cell

DOEpatents

Martin, Charles E; Fontaine, Lucien; Gardner, William H

2014-01-21

An electrochemical cell includes components that are welded from an external source after the components are assembled in a cell canister. The cell canister houses electrode tabs and a core insert. An end cap insert is disposed opposite the core insert. An external weld source, such as a laser beam, is applied to the end cap insert, such that the end cap insert, the electrode tabs, and the core insert are electrically coupled by a weld which extends from the end cap insert to the core insert.

Ceramic gas turbine shroud

DOEpatents

Shi, Jun; Green, Kevin E.

2014-07-22

An example gas turbine engine shroud includes a first annular ceramic wall having an inner side for resisting high temperature turbine engine gasses and an outer side with a plurality of radial slots. A second annular metallic wall is positioned radially outwardly of and enclosing the first annular ceramic wall and has a plurality of tabs in communication with the slot of the first annular ceramic wall. The tabs of the second annular metallic wall and slots of the first annular ceramic wall are in communication such that the first annular ceramic wall and second annular metallic wall are affixed.

Functional photosystem I maintains proper energy balance during nitrogen depletion in Chlamydomonas reinhardtii, promoting triacylglycerol accumulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gargouri, Mahmoud; Bates, Philip D.; Park, Jeong-Jin

Nutrient deprivation causes significant stress to the unicellular microalga, Chlamydomonas reinhardtii, which responds by significantly altering its metabolic program. In following N deprivation, the accumulation of starch and triacylglycerols (TAGs) is significantly altered following massive reprogramming of cellular metabolism. One protein that was found to change dramatically and early to this stress was TAB2, a photosystem I (PSI) translation initiation factor, whose transcript and protein levels increased significantly after only 30 min of N deprivation. A detailed physiological and omics-based analysis of an insertional mutant of Chlamydomonas with reduced TAB2 function was conducted to determine what role the functional PSImore » plays in regulating the cellular response to N deprivation. The tab2 mutant displayed increased acetate assimilation and elevated starch levels during the first 6 h of N deprivation, followed by a shift toward altered amino acid synthesis, reduced TAG content and altered fatty acid profiles. Our results suggested a central role for PSI in controlling cellular metabolism and its implication in regulation of lipid/starch partitioning. Time course analyses of the tab2 mutant versus wild type under N-deprived versus N replete conditions revealed changes in the ATP/NADPH ratio and suggested that TAG biosynthesis may be associated with maintaining the redox state of the cell during N deprivation. The loss of ability to accumulate TAG in the tab2 mutant co-occurred with an up-regulation of photo-protective mechanisms, suggesting that the synthesis of TAG in the wild type occurs not only as a temporal energy sink, but also as a protective electron sink. By exploiting the tab2 mutation in the cells of C. reinhardtii cultured under autotrophic, mixotrophic, and heterotrophic conditions during nitrogen replete growth and for the first 8 days of nitrogen deprivation, we showed that TAG accumulation and lipid/starch partitioning are dynamically regulated by alterations in PSI function, which concomitantly alters the immediate ATP/NADPH demand. This occurs even without removal of nitrogen from the medium, but sufficient external carbon must nevertheless be available. Our efforts to increase lipid accumulation in algae such as Chlamydomonas need to consider carefully how the energy balance of the cell is involved in or affected by such efforts and that numerous layers of metabolic and genetic regulatory control are likely to interfere with such efforts to control oil biosynthesis. Such knowledge will enable synthetic biology approaches to alter the response to the N depletion stress, leading to rewiring of the regulatory networks so that lipid accumulation could be turned on in the absence of N deprivation, allowing for the development of algal production strains with highly enhanced lipid accumulation profiles.« less

Functional photosystem I maintains proper energy balance during nitrogen depletion in Chlamydomonas reinhardtii, promoting triacylglycerol accumulation

DOE PAGES

Gargouri, Mahmoud; Bates, Philip D.; Park, Jeong-Jin; ...

2017-04-13

Nutrient deprivation causes significant stress to the unicellular microalga, Chlamydomonas reinhardtii, which responds by significantly altering its metabolic program. In following N deprivation, the accumulation of starch and triacylglycerols (TAGs) is significantly altered following massive reprogramming of cellular metabolism. One protein that was found to change dramatically and early to this stress was TAB2, a photosystem I (PSI) translation initiation factor, whose transcript and protein levels increased significantly after only 30 min of N deprivation. A detailed physiological and omics-based analysis of an insertional mutant of Chlamydomonas with reduced TAB2 function was conducted to determine what role the functional PSImore » plays in regulating the cellular response to N deprivation. The tab2 mutant displayed increased acetate assimilation and elevated starch levels during the first 6 h of N deprivation, followed by a shift toward altered amino acid synthesis, reduced TAG content and altered fatty acid profiles. Our results suggested a central role for PSI in controlling cellular metabolism and its implication in regulation of lipid/starch partitioning. Time course analyses of the tab2 mutant versus wild type under N-deprived versus N replete conditions revealed changes in the ATP/NADPH ratio and suggested that TAG biosynthesis may be associated with maintaining the redox state of the cell during N deprivation. The loss of ability to accumulate TAG in the tab2 mutant co-occurred with an up-regulation of photo-protective mechanisms, suggesting that the synthesis of TAG in the wild type occurs not only as a temporal energy sink, but also as a protective electron sink. By exploiting the tab2 mutation in the cells of C. reinhardtii cultured under autotrophic, mixotrophic, and heterotrophic conditions during nitrogen replete growth and for the first 8 days of nitrogen deprivation, we showed that TAG accumulation and lipid/starch partitioning are dynamically regulated by alterations in PSI function, which concomitantly alters the immediate ATP/NADPH demand. This occurs even without removal of nitrogen from the medium, but sufficient external carbon must nevertheless be available. Our efforts to increase lipid accumulation in algae such as Chlamydomonas need to consider carefully how the energy balance of the cell is involved in or affected by such efforts and that numerous layers of metabolic and genetic regulatory control are likely to interfere with such efforts to control oil biosynthesis. Such knowledge will enable synthetic biology approaches to alter the response to the N depletion stress, leading to rewiring of the regulatory networks so that lipid accumulation could be turned on in the absence of N deprivation, allowing for the development of algal production strains with highly enhanced lipid accumulation profiles.« less

Long-term Immunogenicity of Elosulfase Alfa in the Treatment of Morquio A Syndrome: Results From MOR-005, a Phase III Extension Study.

PubMed

Long, Brian; Tompkins, Troy; Decker, Celeste; Jesaitis, Lynne; Khan, Shahid; Slasor, Peter; Harmatz, Paul; O'Neill, Charles A; Schweighardt, Becky

2017-01-01

Elosulfase alfa is an enzyme replacement therapy for the treatment of Morquio A syndrome (mucopolysaccharidosis IVA), a lysosomal storage disorder caused by a deficiency of the enzyme N-acetylgalactose-amine-6-sulfatase. We previously reported immunogenicity data from our 24-week placebo-controlled Phase III study, MOR-004. Here, we report the long-term immunogenicity profile of elosulfase alfa from MOR-005, the Phase III extension trial to assess potential correlations between antidrug antibodies and efficacy and safety profile outcomes throughout 120 weeks of treatment. The long-term immunogenicity of elosulfase alfa was evaluated in patients with Morquio A syndrome in an open-label extension study for a total of 120 weeks. All patients received 2.0 mg/kg elosulfase alfa either weekly or every other week before establishment of 2.0 mg/kg/wk as the recommended dose, at which time all patients received weekly treatment. Efficacy measures were compared with those from the MOR-004 baseline, enabling analysis of changes over 120 weeks. The primary efficacy measure was the change from baseline in 6-minute walk test. Secondary measures included changes from baseline in 3-minute stair climb test and normalized urine keratan sulfate, a pharmacodynamic metric. All patients treated with elosulfase alfa developed antidrug total antibodies (TAb) by week 24 of MOR-004. In the extension study, all patients, including those who had previously received placebo, were TAb positive by study week 36 (MOR-005 week 12). All patients remained TAb positive throughout the study, and TAb titers were similar across treatment groups at week 120. Nearly all patients tested positive for neutralizing antibodies (NAb) at least once, with incidence of NAb positivity peaking at 85.9% at study week 36, then steadily declining to 66.0% at study week 120. In all treatment groups, mean urine keratan sulfate remained below treatment-naive baseline despite the presence of antidrug antibodies. No relationship was observed between TAb titers or NAb positivity and changes in urine keratan sulfate, 6-minute walk test, or 3-minute stair climb test from baseline to week 120. No consistent associations were detected between antidrug antibodies and the occurrence of hypersensitivity adverse events or anaphylaxis over the course of the study. Immunogenicity results from this long-term study are consistent with previously reported 24-week results. Despite the sustained presence of antidrug antibodies, elosulfase alfa was well tolerated, and patients continued to benefit from treatment through week 120. No associations were detected between higher TAb titers or NAb positivity and reduced treatment effect or worsened safety profile measures. ClinicalTrials.gov identifier: NCT01415427. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Procarcinogenic effects of cyclosporine A are mediated through the activation of TAK1/TAB1 signaling pathway

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Jianmin; Walsh, Stephanie B.; Verney, Zoe M.

Research highlights: {yields} Organ transplant recipients are highly susceptible to early skin cancer development. {yields} CsA-mediated TGFB1-dependent TAK1/TAB1 signaling augments invasive tumor growth. {yields} CsA enhances accumulation of upstream kinases, ZMP, AMPK and IRAK to activate TAK1. {yields} TAK1 mediates enhanced proliferation and reduced apoptosis via CsA-dependent NF{kappa}B. -- Abstract: Cyclosporine A (CsA) is an immunosuppressive drug commonly used for maintaining chronic immune suppression in organ transplant recipients. It is known that patients receiving CsA manifest increased growth of aggressive non-melanoma skin cancers. However, the underlying mechanism by which CsA augments tumor growth is not fully understood. Here, we showmore » that CsA augments the growth of A431 epidermoid carcinoma xenograft tumors by activating tumor growth factor {beta}-activated kinase1 (TAK1). The activation of TAK1 by CsA occurs at multiple levels by kinases ZMP, AMPK and IRAK. TAK1 forms heterodimeric complexes with TAK binding protein 1 and 2 (TAB1/TAB2) which in term activate nuclear factor {kappa}B (NF{kappa}B) and p38 MAP kinase. Transcriptional activation of NF{kappa}B is evidenced by IKK{beta}-mediated phosphorylation-dependent degradation of I{kappa}B and consequent nuclear translocation of p65. This also leads to enhancement in the expression of its transcriptional target genes cyclin D1, Bcl2 and COX-2. Similarly, activation of p38 leads to enhanced inflammation-related signaling shown by increased phosphorylation of MAPKAPK2 and which in turn phosphorylates its substrate HSP27. Activation of both NF{kappa}B and p38 MAP kinase provide mitogenic stimuli to augment the growth of SCCs.« less

Is intimal hyperplasia a marker of neuro-ophthalmic complications of giant cell arteritis?

PubMed

Makkuni, D; Bharadwaj, A; Wolfe, K; Payne, S; Hutchings, A; Dasgupta, B

2008-04-01

The ischaemic complications of giant cell arteritis (GCA) such as blindness and stroke may result from luminal narrowing of the affected arteries. This study focuses on the association between the severity of intimal proliferation on temporal artery biopsy (TAB) histology and neuro-ophthalmic complications (NOCs) of GCA. We identified 30 cases of biopsy-proven temporal arteritis. One histopathologist (blinded to the clinical details) evaluated the TAB specimens and categorized the degree of maximum stenosis due to intimal hyperplasia into four grades: grade 1 is <50% luminal occlusion due to intimal hyperplasia, grade 2 is 50-75%, grade 3 is >75% and grade 4 is complete luminal occlusion. A second histopathologist (also blinded to the clinical details) independently evaluated the TAB specimens using the same grading system. The NOCs in these patients were noted after a case record review. Of the 30 patients, 12 had NOC-10 with eye complications (complete visual loss, anterior ischaemic neuropathy, visual field defects), one patient had cerebral infarcts and one had both cerebral infarcts and vision loss. There was evidence for a statistically significant trend of NOC associated with higher intimal hyperplasia scores (P = 0.001). The scores of the histopathologists agreed for 23 (77%) patients and differed by 1 category for the remaining 7 (kappa-statistic 0.88). Our study suggests that the degree of intimal hyperplasia on TAB histology (routinely available to all hospital units) seems to be closely associated with NOCs of GCA. The study highlights the possible prognostic as well as diagnostic role of the biopsy. We feel that intimal hyperplasia noted in biopsy specimens may help us in the risk stratification of GCA patients and targeting of appropriate and novel therapies.

Colour compatibility between teeth and dental shade guides in Quinquagenarians and Septuagenarians.

PubMed

Cocking, C; Cevirgen, E; Helling, S; Oswald, M; Corcodel, N; Rammelsberg, P; Reinelt, G; Hassel, A J

2009-11-01

The aim of this investigation was to determine colour compatibility between dental shade guides, namely, VITA Classical (VC) and VITA 3D-Master (3D), and human teeth in quinquagenarians and septuagenarians. Tooth colour, described in terms of L*a*b* values of the middle third of facial tooth surface of 1391 teeth, was measured using VITA Easyshade in 195 subjects (48% female). These were compared with the colours (L*a*b* values) of the shade tabs of VC and 3D. The mean coverage error and the percentage of tooth colours being within a given colour difference (DeltaE(ab)) from the tabs of VC and 3D were calculated. For comparison, hypothetical, optimized, population-specific shade guides were additionally calculated based on discrete optimization techniques for optimizing coverage. Mean coverage error was DeltaE(ab) = 3.51 for VC and DeltaE(ab) = 2.96 for 3D. Coverage of tooth colours by the tabs of VC and 3D within DeltaE(ab) = 2 was 23% and 24%, respectively, (DeltaE(ab)

Concerns Expressed by Parents of Children with Pervasive Developmental Disorders for Different Time Periods of the Day: A Case–Control Study

PubMed Central

Sasaki, Yoshinori; Usami, Masahide; Sasayama, Daimei; Okada, Takashi; Iwadare, Yoshitaka; Watanabe, Kyota; Ushijima, Hirokage; Tanaka, Tetsuya; Harada, Maiko; Tanaka, Hiromi; Kodaira, Masaki; Sugiyama, Nobuhiro; Sawa, Tetsuji; Saito, Kazuhiko

2015-01-01

Background/Aim The Questionnaire: Children with Difficulties (QCD) is a parent-assessed questionnaire designed to evaluate child’s difficulties in functioning during specific periods of the day. This study aimed to evaluate difficulties in daily functioning of children and adolescents with pervasive developmental disorder (PDD) using the QCD. Results were compared with those for a community sample. Methods A case–control design was used. The cases comprised elementary school students (182 males, 51 females) and junior high school students (100 males, 39 females) with PDD, whereas a community sample of elementary school students (568 males, 579 females) and junior high school students (180 males, 183 females) was enrolled as controls. Their behavior was assessed using the QCD, the Tokyo Autistic Behavior Scale (TABS), the ADHD-rating scale (ADHD-RS), and the Oppositional Defiant Behavior Inventory (ODBI) for elementary and junior high school students, respectively. Effects of gender and diagnosis on the QCD scores were analyzed. Correlation coefficients between QCD and TABS, ADHD-RS, and ODBI scores were analyzed. Results The QCD scores for the children with PDD were significantly lower compared with those from the community sample (P < 0.001). Significantly strong correlations were observed in more areas of the ADHD-RS and ODBI scores compared with the TABS scores. Conclusions Children with PDD experienced greater difficulties in completing basic daily activities; moreover, their QCD scores revealed stronger associations with their ADHD-RS and ODBI scores in comparison with their TABS scores. The difficulties of PDD, ADHD and OBDI symptoms combined in children makes it necessary to assess all diagnoses before any therapy for PDD is initiated in order to be able to evaluate its results properly. PMID:25898260

Evaluation of an optimized shade guide made from porcelain powder mixtures.

PubMed

Wang, Peng; Wei, Jiaqiang; Li, Qing; Wang, Yining

2014-12-01

Color errors associated with current shade guides and problems with color selection and duplication are still challenging for restorative dentists. The purpose of this study was to evaluate an optimized shade guide for visual shade duplication. Color distributions (L*, a*, and b*) of the maxillary left central incisors of 236 participants, whose ages ranged from 20 to 60, were measured with a spectrophotometer. Based on this color map, an optimized shade guide was designed with 14 shade tabs evenly distributed within the given color range of the natural incisors. The shade tabs were fabricated with porcelain powder mixtures and conventional laboratory procedures. A comparison of shade duplication by using the optimized and Vitapan Classical shade guides was conducted. Thirty Chinese participants were involved, and the colors of the left maxillary incisors were selected by using 2 shade guides. Metal ceramic crowns were fabricated according to the results of the shade selection. The colors of the shade tabs, natural teeth, and the ceramic crowns were measured with a spectrophotometer. The color differences among the natural teeth, the shade tabs, and the corresponding metal ceramic crowns were calculated and analyzed (α=.017). Significant differences were found in both phases of shade determination and shade duplication (P<.017). The total number of color errors with the optimized shade guide was 3.5, which was significantly less than that of Vitapan, 5.1 (P<.001). The optimized shade guide system improved performance not only in the color selection phase but also in the color of the fabricated crowns. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Accurate shade image matching by using a smartphone camera.

PubMed

Tam, Weng-Kong; Lee, Hsi-Jian

2017-04-01

Dental shade matching by using digital images may be feasible when suitable color features are properly manipulated. Separating the color features into feature spaces facilitates favorable matching. We propose using support vector machines (SVM), which are outstanding classifiers, in shade classification. A total of 1300 shade tab images were captured using a smartphone camera with auto-mode settings and no flash. The images were shot at angled distances of 14-20cm from a shade guide at a clinic equipped with light tubes that produced a 4000K color temperature. The Group 1 samples comprised 1040 tab images, for which the shade guide was randomly positioned in the clinic, and the Group 2 samples comprised 260 tab images, for which the shade guide had a fixed position in the clinic. Rectangular content was cropped manually on each shade tab image and further divided into 10×2 blocks. The color features extracted from the blocks were described using a feature vector. The feature vectors in each group underwent SVM training and classification by using the "leave-one-out" strategy. The top one and three accuracies of Group 1 were 0.86 and 0.98, respectively, and those of Group 2 were 0.97 and 1.00, respectively. This study provides a feasible technique for dental shade classification that uses the camera of a mobile device. The findings reveal that the proposed SVM classification might outperform the shade-matching results of previous studies that have performed similarity measurements of ΔE levels or used an S, a*, b* feature set. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Sunlight Exposure and Breast Density: A Population-Based Study

PubMed Central

Wu, Sheng-Hui; So, Edwin; Lam, Tsz-ping; Woo, Jean; Yuen, PY; Qin, Ling; Ku, Susanna

2013-01-01

Purpose This study aims to assess the association of sunlight exposure with breast cancer risk, measured by the breast density assessed from Tabár's mammographic pattern in Chinese women. Methods A total of 676 premenopausal women were recruited to participate in this study, in which 650 completed a validated sunlight exposure questionnaire via telephone. The mammograms were classified according to Tabár's classification for parenchyma, and patterns IV & V and I, II & III indicated respectively high and low risk mammographic patterns for breast cancer. The odds ratios (OR) and 95% confidence intervals (CIs) for sun exposure-related variables were estimated using unconditional logistic regression with adjustment for potential confounders. Results Among 646 participants, women with high breast cancer risk (Tabár's patterns IV &V) had less hours spent in the sun than those with low risk (I, II & III) at any age stage. A higher level of sunlight exposure was associated with a significantly lower risk having high risk Tabár's pattern. Women aged 40 to 44 years who were in the highest tertile of lifetime total hours spent in the sun had a multi-adjusted OR of 0.41 (95% CI, 0.18-0.92; p for trend=0.03) compared with those in the lowest tertile (>2.19 hr/day vs. <1.32 hr/day). For hours spent in the sun across the ages of 6 to 12 years, the comparable OR was 0.37 (95% CI, 0.15-0.91; p for trend=0.03). Conclusion These findings suggest that higher sunlight exposure is related to a lower risk of having high risk breast density pattern in premenopausal women. Our results also suggest the most relevant period of exposure is during earlier life. PMID:23843849

Loading capacity and interaction of DNA binding on catanionic vesicles with different cationic surfactants.

PubMed

Xu, Lu; Chen, Jingfei; Feng, Lei; Dong, Shuli; Hao, Jingcheng

2014-12-07

Cationic and anionic (catanionic) vesicles were constructed from the mixtures of sodium laurate (SL) and alkyltrimethylammonium bromide (CnTAB, n = 12, 14, and 16) and were used to control the loading capacity of DNA. The binding saturation point (BSP) of DNA to catanionic vesicles increases with the chain length of cationic surfactants, which is at 1.0, 1.3 and 1.5 for CnTAB with n = 12, 14, and 16, respectively. Our measurements showed that the loading capacity and affinity of DNA can be controlled by catanionic vesicles. It increases with the chain length of cationic surfactants. Because of a large reduction in surface charge density, catanionic vesicles are prone to undergo re-aggregation or fusion with the addition of DNA. DNA molecules can still maintain original coil state during the interaction with catanionic CnTAL vesicles. (1)H NMR data reveals that the obvious dissociation of anionic ions, L(-), from catanionic C14TAL vesicles is due to the interaction with DNA; however, this phenomenon cannot be observed in C12TAB-SL vesicles. Agarose gel electrophoresis (AGE) results demonstrate that the electrostatic interaction between the two oppositely charged cationic and anionic surfactants is stronger than that between DNA and cationic surfactant, CnTAB (n = 12, 14, and 16). Not only is the dissociation of L(-) simply determined by the charge competition, but it also depends largely on the variations in the surface charge density as well as the cationic and anionic surfactant competing ability in geometry configuration of catanionic vesicles. The complicated interaction between DNA and catanionic vesicles induces the deformation of cationic vesicles. Our results should provide clear guidance for choosing more proper vectors for DNA delivery and gene therapy in cell experiments.

The significance of pulmonary nodule in breast cancer patients.

PubMed

Daglar, Gul; Yuksek, Yunus Nadi; Gozalan, Ugur; Tutuncu, Tanju; Kama, Nuri Aydin

2010-01-01

Pulmonary nodule in patients with breast cancer is a difficult problem and constitutes a therapeutic challenge. This study questioned the significance of solitary pulmonary nodule in breast cancer patients and compared the survival with patients who had normal thorax tomography. There were 58 breast cancer patients included in the study. From these, 28 patients had normal preoperative tomography (group 1), and 30 patients had pulmonary nodule less than 1 cm on thorax tomography (group 2). Chi-square and Fisher tests were used for comparisons and Kaplan-Meier test for survival. Stage, tumour size, treatment, histology, lymph node involvement, adjuvant therapy, were similar in both groups. We did not find a significant difference in disease-free and overall survival rates, between two groups. For the nodules that show benign properties at tomography, there is no need to do further investigation and no need to change treatment plan in breast cancer patients (Tab. 2, Fig. 2, Ref. 12). Full Text (Free, PDF) www.bmj.sk.

Increase in the circulating level of hepatocyte growth factor in pancreatic cancer patients.

PubMed

Kemik, Ozgur; Purisa, Sevim; Kemik, Ahu Sarbay; Tuzun, Sefa

2009-01-01

Hepatocyte growth factor (HGF) has been reported the cause of many biological events, including cell proliferation, invasiveness, morphogenesis, and angiogenesis. Elevated HGF content in tumor tissue was reported to predict a more aggressive biology in breast and gastric cancer patients. Eighty patients with invasive pancreatic cancer investigated. Venous blood samples were collected before the surgery. Sera were obtained by centrifugation and stored at -70 degrees C until assayed. The control group created from healthy individuals. Serum concentrations of soluble HGF were measured by the quantitative sandwich enzyme immunoassay technique. The mean value of serum soluble HGF in patients with invasive pancreatic cancer was 497.2 +/- 53.8 pg/ml and that of control group was 53.6 +/- 7.5 pg/ml and the difference was significant (p < 0.001). The serum levels of soluble HGF might reflect the severity of invasive pancreatic cancer and deserve further evaluation (Tab. 2, Ref. 19). Full Text (Free, PDF) www.bmj.sk.

The value of fine needle aspiration and cytologic examination of impalpable complicated breast cysts.

PubMed

Tez, Selda; Dener, Cenap; Köktener, Aslý; Caydere, Muzaffer; Tez, Mesut

2008-01-01

The purpose of the study was to evaluate the utility of fine needle aspiration--FNA and cytologic analysis of impalpable complicated breast cysts. We rewieved the imaging findings, aspiration, cytology and biopsy results and followup imaging findings of 246 complicated cysts in 166 women retrospectively. FNA was performed in 169 out of the 246 complicated cysts. Thirtyone lesions were followed-up with US. Surgical biopsy was performed from five lesions. No malignant cells (137 cysts), insufficient cellular material (17 cysts), atypical cells (4 cysts) were seen in cytological examination of the aspirates. None of these lesions were found to represent malignancy at the time of surgical excision and during follow-up. Impalpable complicated breast cysts may be classified as probably benign and can be managed with follow-up imaging studies instead of intervention. Routine cytologic examination is unnecessary if the fluid is not bloody (Tab. 2, Ref. 18). Full Text (Free, PDF) www.bmj.sk.

Southern California Earthquake Center Geologic Vertical Motion Database

NASA Astrophysics Data System (ADS)

Niemi, Nathan A.; Oskin, Michael; Rockwell, Thomas K.

2008-07-01

The Southern California Earthquake Center Geologic Vertical Motion Database (VMDB) integrates disparate sources of geologic uplift and subsidence data at 104- to 106-year time scales into a single resource for investigations of crustal deformation in southern California. Over 1800 vertical deformation rate data points in southern California and northern Baja California populate the database. Four mature data sets are now represented: marine terraces, incised river terraces, thermochronologic ages, and stratigraphic surfaces. An innovative architecture and interface of the VMDB exposes distinct data sets and reference frames, permitting user exploration of this complex data set and allowing user control over the assumptions applied to convert geologic and geochronologic information into absolute uplift rates. Online exploration and download tools are available through all common web browsers, allowing the distribution of vertical motion results as HTML tables, tab-delimited GIS-compatible text files, or via a map interface through the Google Maps™ web service. The VMDB represents a mature product for research of fault activity and elastic deformation of southern California.

The antitussive activity of polysaccharides from Althaea officinalis l., var. Robusta, Arctium lappa L., var. Herkules, and Prunus persica L., Batsch.

PubMed

Sutovska, M; Nosalova, G; Franova, S; Kardosova, A

2007-01-01

The therapy of pathological type of cough presents serious medical problem. The aim of experiments was to investigate polysaccacharide influence on experimentally induced cough. The purified and/or modified polysaccharides from the flowers and plants, characterized by chemical composition and molecular properties were subjected to tests for antitussive activity on cough, induced mechanically in conscious cats of both sexes. The results revealed that the tested polysaccharides exhibited statistically significant cough-suppressing activity, which was noticeably higher than that of the non-narcotic drug used in clinical practice to treat coughing. The most expressive antitussive activity was observed with the polysaccharide from marsh mallow, containing the highest proportion of the uronic acid constituent. Negative influence of the tested compounds on expectoration was negligible when compared to that of codeine. Antitussive activity of various plant polysaccharides was confirmed. These results allow ranging them among prospective antitussive agents (Tab. 2, Fig. 6, Ref. 15) Full Text (Free, PDF) www.bmj.sk.

Stem cell motility enables a density-dependent rate of fate commitment during scaled resizing of adult organs

NASA Astrophysics Data System (ADS)

Du, Xinxin; O'Brien, Lucy; Riedel-Kruse, Ingmar

Many adult organs grow or shrink to accommodate fluctuating levels of physiological demand. Specifically, the intestine of the fruit fly (the midgut) expands four-fold in the number of mature cells and, proportionally, the number of stem cells when the fly eats. However, the cellular behaviors that give rise to this stem scaling are not well-understood. Here we present a biophysical model of the adult fly midgut. A set of differential equations can recapitulate the physiological kinetics of cells during midgut growth and shrinkage as long as the rate of stem cell fate commitment depends on the stem cell number density in the tissue. To elucidate the source of this dependence, we model the tissue in a 2D simulation with soft spheres, where stem cells choose fate commitment through Delta-Notch pathway interactions with other stem cells, a known process in fly midguts. We find that as long as stem cells exhibit a large enough amplitude of random motion through the tissue (`stem cell motility'), and explore a large enough `territory' in their lifetime, stem cell scaling can occur. These model observations are confirmed through in vivo live-imaging, where we indeed see that stem cells are motile in the fly midgut.

Reentry heat transfer analysis of the space shuttle orbiter

NASA Technical Reports Server (NTRS)

Ko, W. L.; Quinn, R. D.; Gong, L.

1982-01-01

A structural performance and resizing finite element thermal analysis computer program was used in the reentry heat transfer analysis of the space shuttle. Two typical wing cross sections and a midfuselage cross section were selected for the analysis. The surface heat inputs to the thermal models were obtained from aerodynamic heating analyses, which assumed a purely turbulent boundary layer, a purely laminar boundary layer, separated flow, and transition from laminar to turbulent flow. The effect of internal radiation was found to be quite significant. With the effect of the internal radiation considered, the wing lower skin temperature became about 39 C (70 F) lower. The results were compared with fight data for space transportation system, trajectory 1. The calculated and measured temperatures compared well for the wing if laminar flow was assumed for the lower surface and bay one upper surface and if separated flow was assumed for the upper surfaces of bays other than bay one. For the fuselage, good agreement between the calculated and measured data was obtained if laminar flow was assumed for the bottom surface. The structural temperatures were found to reach their peak values shortly before touchdown. In addition, the finite element solutions were compared with those obtained from the conventional finite difference solutions.

Precision Closed-Loop Orbital Maneuvering System Design and Performance for the Magnetospheric Multi-Scale Mission (MMS) Formation

NASA Technical Reports Server (NTRS)

Chai, Dean; Queen, Steve; Placanica, Sam

2015-01-01

NASA's Magnetospheric Multi-Scale (MMS) mission successfully launched on March 13, 2015 (UTC) consists of four identically instrumented spin-stabilized observatories that function as a constellation to study magnetic reconnection in space. The need to maintain sufficiently accurate spatial and temporal formation resolution of the observatories must be balanced against the logistical constraints of executing overly-frequent maneuvers on a small fleet of spacecraft. These two considerations make for an extremely challenging maneuver design problem. This paper focuses on the design elements of a 6-DOF spacecraft attitude control and maneuvering system capable of delivering the high-precision adjustments required by the constellation designers---specifically, the design, implementation, and on-orbit performance of the closed-loop formation-class maneuvers that include initialization, maintenance, and re-sizing. The maneuvering control system flown on MMS utilizes a micro-gravity resolution accelerometer sampled at a high rate in order to achieve closed-loop velocity tracking of an inertial target with arc-minute directional and millimeter-per-second magnitude accuracy. This paper summarizes the techniques used for correcting bias drift, sensor-head offsets, and centripetal aliasing in the acceleration measurements. It also discusses the on-board pre-maneuver calibration and compensation algorithms as well as the implementation of the post-maneuver attitude adjustments.

Precision Closed-Loop Orbital Maneuvering System Design and Performance for the Magnetospheric Multiscale Formation

NASA Technical Reports Server (NTRS)

Chai, Dean J.; Queen, Steven Z.; Placanica, Samuel J.

2015-01-01

NASAs Magnetospheric Multiscale (MMS) mission successfully launched on March 13,2015 (UTC) consists of four identically instrumented spin-stabilized observatories that function as a constellation to study magnetic reconnection in space. The need to maintain sufficiently accurate spatial and temporal formation resolution of the observatories must be balanced against the logistical constraints of executing overly-frequent maneuvers on a small fleet of spacecraft. These two considerations make for an extremely challenging maneuver design problem. This paper focuses on the design elements of a 6-DOF spacecraft attitude control and maneuvering system capable of delivering the high-precision adjustments required by the constellation designers specifically, the design, implementation, and on-orbit performance of the closed-loop formation-class maneuvers that include initialization, maintenance, and re-sizing. The maneuvering control system flown on MMS utilizes a micro-gravity resolution accelerometer sampled at a high rate in order to achieve closed-loop velocity tracking of an inertial target with arc-minute directional and millimeter-per second magnitude accuracy. This paper summarizes the techniques used for correcting bias drift, sensor-head offsets, and centripetal aliasing in the acceleration measurements. It also discusses the on-board pre-maneuver calibration and compensation algorithms as well as the implementation of the post-maneuver attitude adjustments.

Low Velocity Airdrop Tests of an X-38 Backup Parachute Design

NASA Technical Reports Server (NTRS)

Stein, Jenny M.; Machin, Ricardo A.; Wolf, Dean F.; Hillebrandt, F. David

2007-01-01

The NASA Johnson Space Center's X-38 program designed a new backup parachute system to recover the 25,000 lb X-38 prototype for the Crew Return Vehicle spacecraft. Due to weight and cost constraints, the main backup parachute design incorporated rapid and low cost fabrication techniques using off-the-shelf materials. Near the vent, the canopy was constructed of continuous ribbons, to provide more damage tolerance. The remainder of the canopy was a constructed with a continuous ringslot design. After cancellation of the X-38 program, the parachute design was resized, built, and drop tested for Natick Soldiers Center's Low Velocity Air Drop (LVAD) program to deliver cargo loads up to 22,000 lbs from altitudes as low as 500 feet above the ground. Drop tests results showed that the 500-foot LVAD parachute deployment conditions cause severe skirt inversion and inflation problems for large parachutes. The bag strip occurred at a high angle of attack, causing skirt inversion before the parachute could inflate. The addition of a short reefing line prevented the skirt inversion. Using a lower porosity in the vent area, than is normally used in large parachutes, improved inflation. The drop testing demonstrated that the parachute design could be refined to meet the requirements for the 500-foot LVAD mission.

Classification of SD-OCT volumes for DME detection: an anomaly detection approach

NASA Astrophysics Data System (ADS)

Sankar, S.; Sidibé, D.; Cheung, Y.; Wong, T. Y.; Lamoureux, E.; Milea, D.; Meriaudeau, F.

2016-03-01

Diabetic Macular Edema (DME) is the leading cause of blindness amongst diabetic patients worldwide. It is characterized by accumulation of water molecules in the macula leading to swelling. Early detection of the disease helps prevent further loss of vision. Naturally, automated detection of DME from Optical Coherence Tomography (OCT) volumes plays a key role. To this end, a pipeline for detecting DME diseases in OCT volumes is proposed in this paper. The method is based on anomaly detection using Gaussian Mixture Model (GMM). It starts with pre-processing the B-scans by resizing, flattening, filtering and extracting features from them. Both intensity and Local Binary Pattern (LBP) features are considered. The dimensionality of the extracted features is reduced using PCA. As the last stage, a GMM is fitted with features from normal volumes. During testing, features extracted from the test volume are evaluated with the fitted model for anomaly and classification is made based on the number of B-scans detected as outliers. The proposed method is tested on two OCT datasets achieving a sensitivity and a specificity of 80% and 93% on the first dataset, and 100% and 80% on the second one. Moreover, experiments show that the proposed method achieves better classification performances than other recently published works.

GeneOnEarth: fitting genetic PC plots on the globe.

PubMed

Torres-Sánchez, Sergio; Medina-Medina, Nuria; Gignoux, Chris; Abad-Grau, María M; González-Burchard, Esteban

2013-01-01

Principal component (PC) plots have become widely used to summarize genetic variation of individuals in a sample. The similarity between genetic distance in PC plots and geographical distance has shown to be quite impressive. However, in most situations, individual ancestral origins are not precisely known or they are heterogeneously distributed; hence, they are hardly linked to a geographical area. We have developed GeneOnEarth, a user-friendly web-based tool to help geneticists to understand whether a linear isolation-by-distance model may apply to a genetic data set; thus, genetic distances among a set of individuals resemble geographical distances among their origins. Its main goal is to allow users to first apply a by-view Procrustes method to visually learn whether this model holds. To do that, the user can choose the exact geographical area from an on line 2D or 3D world map by using, respectively, Google Maps or Google Earth, and rotate, flip, and resize the images. GeneOnEarth can also compute the optimal rotation angle using Procrustes analysis and assess statistical evidence of similarity when a different rotation angle has been chosen by the user. An online version of GeneOnEarth is available for testing and using purposes at http://bios.ugr.es/GeneOnEarth.

KSC-04pd1348

NASA Image and Video Library

2004-06-25

KENNEDY SPACE CENTER, FLA. - At right, technicians at Astrotech in Titusville, Fla., guide into place the second solar panel to be installed on NASA’s MESSENGER spacecraft. At left is the first panel already installed. The two large solar panels, supplemented with a nickel-hydrogen battery, will provide MESSENGER’s power. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

Mobile-Cloud Assisted Video Summarization Framework for Efficient Management of Remote Sensing Data Generated by Wireless Capsule Sensors

PubMed Central

Mehmood, Irfan; Sajjad, Muhammad; Baik, Sung Wook

2014-01-01

Wireless capsule endoscopy (WCE) has great advantages over traditional endoscopy because it is portable and easy to use, especially in remote monitoring health-services. However, during the WCE process, the large amount of captured video data demands a significant deal of computation to analyze and retrieve informative video frames. In order to facilitate efficient WCE data collection and browsing task, we present a resource- and bandwidth-aware WCE video summarization framework that extracts the representative keyframes of the WCE video contents by removing redundant and non-informative frames. For redundancy elimination, we use Jeffrey-divergence between color histograms and inter-frame Boolean series-based correlation of color channels. To remove non-informative frames, multi-fractal texture features are extracted to assist the classification using an ensemble-based classifier. Owing to the limited WCE resources, it is impossible for the WCE system to perform computationally intensive video summarization tasks. To resolve computational challenges, mobile-cloud architecture is incorporated, which provides resizable computing capacities by adaptively offloading video summarization tasks between the client and the cloud server. The qualitative and quantitative results are encouraging and show that the proposed framework saves information transmission cost and bandwidth, as well as the valuable time of data analysts in browsing remote sensing data. PMID:25225874

GenomeD3Plot: a library for rich, interactive visualizations of genomic data in web applications.

PubMed

Laird, Matthew R; Langille, Morgan G I; Brinkman, Fiona S L

2015-10-15

A simple static image of genomes and associated metadata is very limiting, as researchers expect rich, interactive tools similar to the web applications found in the post-Web 2.0 world. GenomeD3Plot is a light weight visualization library written in javascript using the D3 library. GenomeD3Plot provides a rich API to allow the rapid visualization of complex genomic data using a convenient standards based JSON configuration file. When integrated into existing web services GenomeD3Plot allows researchers to interact with data, dynamically alter the view, or even resize or reposition the visualization in their browser window. In addition GenomeD3Plot has built in functionality to export any resulting genome visualization in PNG or SVG format for easy inclusion in manuscripts or presentations. GenomeD3Plot is being utilized in the recently released Islandviewer 3 (www.pathogenomics.sfu.ca/islandviewer/) to visualize predicted genomic islands with other genome annotation data. However, its features enable it to be more widely applicable for dynamic visualization of genomic data in general. GenomeD3Plot is licensed under the GNU-GPL v3 at https://github.com/brinkmanlab/GenomeD3Plot/. brinkman@sfu.ca. © The Author 2015. Published by Oxford University Press.

The influence of sulcus width on simulated electric fields induced by transcranial magnetic stimulation

NASA Astrophysics Data System (ADS)

Janssen, A. M.; Rampersad, S. M.; Lucka, F.; Lanfer, B.; Lew, S.; Aydin, Ü.; Wolters, C. H.; Stegeman, D. F.; Oostendorp, T. F.

2013-07-01

Volume conduction models can help in acquiring knowledge about the distribution of the electric field induced by transcranial magnetic stimulation. One aspect of a detailed model is an accurate description of the cortical surface geometry. Since its estimation is difficult, it is important to know how accurate the geometry has to be represented. Previous studies only looked at the differences caused by neglecting the complete boundary between cerebrospinal fluid (CSF) and grey matter (Thielscher et al 2011 NeuroImage 54 234-43, Bijsterbosch et al 2012 Med. Biol. Eng. Comput. 50 671-81), or by resizing the whole brain (Wagner et al 2008 Exp. Brain Res. 186 539-50). However, due to the high conductive properties of the CSF, it can be expected that alterations in sulcus width can already have a significant effect on the distribution of the electric field. To answer this question, the sulcus width of a highly realistic head model, based on T1-, T2- and diffusion-weighted magnetic resonance images, was altered systematically. This study shows that alterations in the sulcus width do not cause large differences in the majority of the electric field values. However, considerable overestimation of sulcus width produces an overestimation of the calculated field strength, also at locations distant from the target location.

KSC-04pd1371

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - - After the deployment test of two solar panels at Astrotech in Titusville, Fla., technicians with The Johns Hopkins University Applied Physics Laboratory (APL) prepare the MESSESNGER spacecraft for a move to a hazardous processing facility in preparation for loading the spacecraft’s complement of hypergolic propellants. The solar arrays will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by APL in Laurel, Md.

KSC-04pd1364

NASA Image and Video Library

2004-06-28

KENNEDY SPACE CENTER, FLA. - At Astrotech in Titusville, Fla., NASA Mission Integration Manager Cheryle Mako and NASA Launch Site Integration Manager John Hueckel talk before the deployment of the solar array panels on the MESSENGER spacecraft behind them. The solar arrays will provide MESSENGER’s power on its journey to Mercury. MESSENGER is scheduled to launch Aug. 2 aboard a Boeing Delta II rocket from Pad 17-B, Cape Canaveral Air Force Station, Fla. It will return to Earth for a gravity boost in July 2005, then fly past Venus twice, in October 2006 and June 2007. The spacecraft uses the tug of Venus’ gravity to resize and rotate its trajectory closer to Mercury’s orbit. Three Mercury flybys, each followed about two months later by a course-correction maneuver, put MESSENGER in position to enter Mercury orbit in March 2011. During the flybys, MESSENGER will map nearly the entire planet in color, image most of the areas unseen by Mariner 10, and measure the composition of the surface, atmosphere and magnetosphere. It will be the first new data from Mercury in more than 30 years - and invaluable for planning MESSENGER’s year-long orbital mission. MESSENGER was built for NASA by the Johns Hopkins University Applied Physics Laboratory in Laurel, Md.

Life Cycle Assessment of Vehicle Lightweighting: A Physics-Based Model To Estimate Use-Phase Fuel Consumption of Electrified Vehicles

DOE PAGES

Kim, Hyung Chul; Wallington, Timothy J.

2016-08-17

Assessing the life-cycle benefits of vehicle lightweighting requires a quantitative description of mass-induced fuel consumption (MIF) and fuel reduction values (FRVs). We have extended our physics-based model of MIF and FRVs for internal combustion engine vehicles (ICEVs) to electrified vehicles (EVs) including hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs). We illustrate the utility of the model by calculating MIFs and FRVs for 37 EVs and 13 ICEVs. BEVs have much smaller MIF and FRVs, both in the range 0.04-0.07 L e/(100 km 100 kg), than those for ICEVs which are in the rangesmore » 0.19-0.32 and 0.16-0.22 L/(100 km 100 kg), respectively. The MIF and FRVs for HEVs and PHEVs mostly lie between those for ICEVs and BEVs. Powertrain resizing increases the FRVs for ICEVs, HEVs and PHEVs. Lightweighting EVs is less effective in reducing greenhouse gas emissions than lightweighting ICEVs, however the benefits differ substantially for different vehicle models. The physics-based approach outlined here enables model specific assessments for ICEVs, HEVs, PHEVs, and BEVs required to determine the optimal strategy for maximizing the life-cycle benefits of lightweighting the light-duty vehicle fleet.« less

Life Cycle Assessment of Vehicle Lightweighting: A Physics-Based Model To Estimate Use-Phase Fuel Consumption of Electrified Vehicles.

PubMed

Kim, Hyung Chul; Wallington, Timothy J

2016-10-18

Assessing the life-cycle benefits of vehicle lightweighting requires a quantitative description of mass-induced fuel consumption (MIF) and fuel reduction values (FRVs). We have extended our physics-based model of MIF and FRVs for internal combustion engine vehicles (ICEVs) to electrified vehicles (EVs) including hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs). We illustrate the utility of the model by calculating MIFs and FRVs for 37 EVs and 13 ICEVs. BEVs have much smaller MIF and FRVs, both in the range 0.04-0.07 L e /(100 km 100 kg), than those for ICEVs which are in the ranges 0.19-0.32 and 0.16-0.22 L/(100 km 100 kg), respectively. The MIF and FRVs for HEVs and PHEVs mostly lie between those for ICEVs and BEVs. Powertrain resizing increases the FRVs for ICEVs, HEVs and PHEVs. Lightweighting EVs is less effective in reducing greenhouse gas emissions than lightweighting ICEVs, however the benefits differ substantially for different vehicle models. The physics-based approach outlined here enables model specific assessments for ICEVs, HEVs, PHEVs, and BEVs required to determine the optimal strategy for maximizing the life-cycle benefits of lightweighting the light-duty vehicle fleet.

Current progress in tissue engineering of heart valves: multiscale problems, multiscale solutions.

PubMed

Cheung, Daniel Y; Duan, Bin; Butcher, Jonathan T

2015-01-01

Heart valve disease is an increasingly prevalent and clinically serious condition. There are no clinically effective biological diagnostics or treatment strategies. The only recourse available is replacement with a prosthetic valve, but the inability of these devices to grow or respond biologically to their environments necessitates multiple resizing surgeries and life-long coagulation treatment, especially in children. Tissue engineering has a unique opportunity to impact heart valve disease by providing a living valve conduit, capable of growth and biological integration. This review will cover current tissue engineering strategies in fabricating heart valves and their progress towards the clinic, including molded scaffolds using naturally derived or synthetic polymers, decellularization, electrospinning, 3D bioprinting, hybrid techniques, and in vivo engineering. Whereas much progress has been made to create functional living heart valves, a clinically viable product is not yet realized. The next leap in engineered living heart valves will require a deeper understanding of how the natural multi-scale structural and biological heterogeneity of the tissue ensures its efficient function. Related, improved fabrication strategies must be developed that can replicate this de novo complexity, which is likely instructive for appropriate cell differentiation and remodeling whether seeded with autologous stem cells in vitro or endogenously recruited cells.

Semantic transcoding of video based on regions of interest

NASA Astrophysics Data System (ADS)

Lim, Jeongyeon; Kim, Munchurl; Kim, Jong-Nam; Kim, Kyeongsoo

2003-06-01

Traditional transcoding on multimedia has been performed from the perspectives of user terminal capabilities such as display sizes and decoding processing power, and network resources such as available network bandwidth and quality of services (QoS) etc. The adaptation (or transcoding) of multimedia contents to given such constraints has been made by frame dropping and resizing of audiovisual, as well as reduction of SNR (Signal-to-Noise Ratio) values by saving the resulting bitrates. Not only such traditional transcoding is performed from the perspective of user"s environment, but also we incorporate a method of semantic transcoding of audiovisual based on region of interest (ROI) from user"s perspective. Users can designate their interested parts in images or video so that the corresponding video contents can be adapted focused on the user"s ROI. We incorporate the MPEG-21 DIA (Digital Item Adaptation) framework in which such semantic information of the user"s ROI is represented and delivered to the content provider side as XDI (context digital item). Representation schema of our semantic information of the user"s ROI has been adopted in MPEG-21 DIA Adaptation Model. In this paper, we present the usage of semantic information of user"s ROI for transcoding and show our system implementation with experimental results.

Deep-cascade: Cascading 3D Deep Neural Networks for Fast Anomaly Detection and Localization in Crowded Scenes.

PubMed

Sabokrou, Mohammad; Fayyaz, Mohsen; Fathy, Mahmood; Klette, Reinhard

2017-02-17

This paper proposes a fast and reliable method for anomaly detection and localization in video data showing crowded scenes. Time-efficient anomaly localization is an ongoing challenge and subject of this paper. We propose a cubicpatch- based method, characterised by a cascade of classifiers, which makes use of an advanced feature-learning approach. Our cascade of classifiers has two main stages. First, a light but deep 3D auto-encoder is used for early identification of "many" normal cubic patches. This deep network operates on small cubic patches as being the first stage, before carefully resizing remaining candidates of interest, and evaluating those at the second stage using a more complex and deeper 3D convolutional neural network (CNN). We divide the deep autoencoder and the CNN into multiple sub-stages which operate as cascaded classifiers. Shallow layers of the cascaded deep networks (designed as Gaussian classifiers, acting as weak single-class classifiers) detect "simple" normal patches such as background patches, and more complex normal patches are detected at deeper layers. It is shown that the proposed novel technique (a cascade of two cascaded classifiers) performs comparable to current top-performing detection and localization methods on standard benchmarks, but outperforms those in general with respect to required computation time.

Collaborative decision-making on wind power projects based on AHP method

NASA Astrophysics Data System (ADS)

Badea, A.; Proştean, G.; Tămăşilă, M.; Vârtosu, A.

2017-01-01

The complexity of projects implementation in Renewable Energy Sources (RES) requires finding collaborative alliances between suppliers and project developers in RES. Links activities in supply chain in RES, respectively, transportation of heavy components, processing orders to purchase quality raw materials, storage and materials handling, packaging, and other complex activities requiring a logistics system collaboratively to be permanently dimensioned properly selected and monitored. Requirements imposed by stringency of wind power energy projects implementation inevitably involves constraints in infrastructure, implementation and logistics. Thus, following an extensive research in RES project, to eliminate these constraints were identified alternative collaboration to provide feasible solutions on different levels of performance. The paper presents a critical analysis of different collaboration alternatives in supply chain for RES projects, selecting the ones most suitable for particular situations by using decision-making method Analytic Hierarchy Process (AHP). The role of AHP method was to formulate a decision model by which can be establish the collaboration alternative choice through mathematical calculation to reduce the impact created by constraints encountered. The solution provided through AHP provides a framework for detecting optimal alternative collaboration between suppliers and project developers in RES and avoids some breaks in the chain by resizing safety buffers for leveling orders in RES projects.

Mobile-cloud assisted video summarization framework for efficient management of remote sensing data generated by wireless capsule sensors.

PubMed

Mehmood, Irfan; Sajjad, Muhammad; Baik, Sung Wook

2014-09-15

Wireless capsule endoscopy (WCE) has great advantages over traditional endoscopy because it is portable and easy to use, especially in remote monitoring health-services. However, during the WCE process, the large amount of captured video data demands a significant deal of computation to analyze and retrieve informative video frames. In order to facilitate efficient WCE data collection and browsing task, we present a resource- and bandwidth-aware WCE video summarization framework that extracts the representative keyframes of the WCE video contents by removing redundant and non-informative frames. For redundancy elimination, we use Jeffrey-divergence between color histograms and inter-frame Boolean series-based correlation of color channels. To remove non-informative frames, multi-fractal texture features are extracted to assist the classification using an ensemble-based classifier. Owing to the limited WCE resources, it is impossible for the WCE system to perform computationally intensive video summarization tasks. To resolve computational challenges, mobile-cloud architecture is incorporated, which provides resizable computing capacities by adaptively offloading video summarization tasks between the client and the cloud server. The qualitative and quantitative results are encouraging and show that the proposed framework saves information transmission cost and bandwidth, as well as the valuable time of data analysts in browsing remote sensing data.

Current Progress in Tissue Engineering of Heart Valves: Multiscale Problems, Multiscale Solutions

PubMed Central

Cheung, Daniel Y; Duan, Bin; Butcher, Jonathan T.

2016-01-01

Introduction Heart valve disease is an increasingly prevalent and clinically serious condition. There are no clinically effective biological diagnostics or treatment strategies. The only recourse available is replacement with a prosthetic valve, but the inability of these devices to grow or respond biologically to their environments necessitates multiple resizing surgeries and life-long coagulation treatment, especially in children. Tissue engineering has a unique opportunity to impact heart valve disease by providing a living valve conduit, capable of growth and biological integration. Areas covered This review will cover current tissue engineering strategies in fabricating heart valves and their progress towards the clinic, including molded scaffolds using naturally-derived or synthetic polymers, decellularization, electrospinning, 3D bioprinting, hybrid techniques, and in vivo engineering. Expert opinion While much progress has been made to create functional living heart valves, a clinically viable product is not yet realized. The next leap in engineered living heart valves will require a deeper understanding of how the natural multi-scale structural and biological heterogeneity of the tissue ensures its efficient function. Related, improved fabrication strategies must be developed that can replicate this de novo complexity, which is likely instructive for appropriate cell differentiation and remodeling whether seeded with autologous stem cells in vitro or endogenously recruited cells. PMID:26027436

Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel

NASA Technical Reports Server (NTRS)

Hunton, Lynn W.

1947-01-01

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Inviscid Flow Computations of Two '07 Mars Lander Aeroshell Configurations Over a Mach Number Range of 2 to 24

NASA Technical Reports Server (NTRS)

Prabhu, Ramadas K.

2001-01-01

This report documents the results of an inviscid computational study conducted on two aeroshell configurations for a proposed '07 Mars Lander. The aeroshell configurations are asymmetric due to the presence of the tabs at the maximum diameter location. The purpose of these tabs was to change the pitching moment characteristics so that the aeroshell will trim at a non-zero angle of attack and produce a lift-to-drag ratio of approximately -0.25. This is required in the guidance of the vehicle on its trajectory. One of the two configurations is called the shelf and the other is called the tab. The unstructured grid software FELISA with the equilibrium Mars gas option was used for these computations. The computations were done for six points on a preliminary trajectory of the '07 Mars Lander at nominal Mach numbers of 2, 3, 5, 10, 15, and 24. Longitudinal aerodynamic characteristics namely lift, drag, and pitching moment were computed for 10, 15, and 20 degrees angles of attack. The results indicated that the two configurations have aerodynamic characteristics that have very similar aerodynamic characteristics, and provide the desired trim LID of approximately -0.25.

Saddle clamp assembly

NASA Technical Reports Server (NTRS)

Belrose, Charles R. (Inventor)

1994-01-01

A saddle clamp assembly is presented. The assembly is comprised of a hollow cylindrical body centered about a longitudinal axis and being diametrically split into semicircular top and bottom sections. Each section has a pair of connection flanges, at opposite ends, that project radially outward. A pair of bolts are retained on the top section flanges and are threadable into nuts retained on the bottom section flanges. A base member is anchored to a central underside portion of the bottom clamp body section and has a pair of connection tabs positioned beneath the bottom clamp body section connection flanges on opposite sides of the clamp axis. A pair of bolts are retained on the base member connection tabs and are threadable into a pair of nuts retainable on a support structure. The connection tab and connection flanges on each side of the clamp body are axially offset in a manner permitting downward installation/removable tool access to the lower bolts past the connection flanges. An elongated retention tether is used to connect the top clamp body section to the balance of the clamp assembly. This prevents loss of the top clamp body section when it is removed from the bottom clamp body section.

[Comparison of the color difference between teeth underwent cold light whitening and two kinds of shade guides].

PubMed

Xu, Y X

2018-06-18

To investigate which shade guide, Vitapan Classical or Vita Bleachedguide 3DMaster, is better matched with the color of teeth in judging whitening effect, by comparing the color difference between shade tabs and corresponding teeth underwent cold light tooth whitening. A total of 60 patients underwent Beyond cold light tooth whitening from May 2014 to April 2016. The patients were divided into two experimental groups according to the shade guide used. Vitapan Classical shade guide was used to judge whitening effect in one group, and Vita Bleachedguide 3DMaster shade guide was used in another. Shade matching was carried out before and after whitening in both the two groups, and the results were recorded by digital photographs. Shade matching procedures were carried out by two doctors independently. If they chose the same tab, it would be seen as the shade matching result; While if they chose different tabs, another doctor would be invited to make a decision. Photographs were taken in preset conditions: intraoral photos of the full dentition in the front, and the proportion of shooting was 1:3; aperture was F22; shutter speed was 1/200; intensity of flash was M/8; ISO value was 200. The photographs were analyzed by Photoshop software. Chromatic values were measured, and color difference values were calculated. Measuring of chromatic values was carried out by three doctors independently, and all the photos were measured twice by each doctor. Six measure results of each photo were recorded, and the maximum and the minimum were excluded, then the mean was seen as the final result. The color difference values were compared by independent-sample t test. Besides, changes of shade tabs after whitening in the two groups were recorded. Color difference value was 5.06±1.71 in Vitapan Classical group, and 3.39±1.36 in Vita Bleachedguide 3D-Master group. There was statistically significant difference between the two groups (t=4.68,P<0.001). Change of shade tabs was 3.63±1.75 in Vitapan Classical group, and 2.23±1.01 in Vita Bleachedguide 3DMaster group. Vita Bleachedguide 3D-Master is better matched with the color of teeth, so it is preferred in judging the effect of cold light tooth whitening.

Jet Evolution Visualized and Quantified Using Filtered Rayleigh Scattering

NASA Technical Reports Server (NTRS)

Reeder, Mark F.

1996-01-01

Filtered Rayleigh scattering was utilized as a flow diagnostic in an investigation of a method for enhancing mixing in supersonic jets. The primary objectives of the study were to visualize the effect of vortex generating tabs on supersonic jets, to exact quantitative data from these planar visualizations, and to detect the presence of secondary flows (i.e., streamwise vorticity) generated by the tabs. An injection seeded frequency-doubled Nd:YAG was the light source and a 14 bit Princeton Instruments iodine charge coupled display (ICCD) camera recorded the image through an iodine cell. The incident wave length of the laser was held constant for each flow case so that the filter absorbed unwanted background light, but permitted part of the thermally broadened Rayleigh scattering light to pas through. The visualizations were performed for axisymmetric jets (D=1.9 cm) operated at perfectly expanded conditions for Mach 1.0, 1.5, and 2.0. All data were recorded for the jet cross section at x/D=3. One hundred instantaneous images were recorded and averaged for each case, with a threshold set to eliminate unavoidable particulate scattering. A key factor in these experiments was that the stagnation air was heated such that the expansion of the flow in the nozzle resulted in the static temperature in the jet being equal to the ambient temperature, assuming isentropic flow. Since the thermodynamic conditions of the flow were approximately the same for each case, increases in the intensity recorded by the ICCD camera could be directly attributed to the Doppler shift, and hence velocity. Visualizations were performed for Mach 1.5 and Mach 2.0 jets with tabs inserted at the nozzle exit. The distortion of the jet was readily apparent and was consistent with Mie scattering-based visualizations. Asymmetry in the intensities of the images indicate the presence of secondary flow patterns which are consistent with the streamwise vortices measured using more traditional diagnostics in subsonic jets with the same tab configurations. Because each tab causes shocks to form, the assumption of isentropic flow is not valid for these cases. However, within a reasonable first-order estimation,the intensity across the illuminated plane for these cases can be related to a value combining density and velocity.

About some processes of replacement of PGM from the placers of Southern Siberia

NASA Astrophysics Data System (ADS)

Shvedov, G. I.; Knyazev, V. N.; Nekos, V. V.

2003-04-01

Authors observed a series of replacement (conversions) in PGM from gold-bearing placers of southern part of Krasnoyarsk region. These facts have mineralogical and genetic interest. In researched placers primary PGM are presented by solid solutions Os-Ir-Ru with different ratios of main elements from osmium to iridium (by classification of D. Harris and L. Cabri /5 /. At smaller amounts Pt-Fe and sperrylite are presented, and other PGM were found in single cases. In minerals of Os-Ir-Ru system the main typical replacement is the forming of edgings of phase (Os,Ir,Ru)S_2 upon the edges of native Os, Ir, Ru or rutheniridosmine. Usually, the process of transformation takes place in grains in a direction of the best permeability, i.e. along deformational gaps or along planes of cleavage, because the phases of this system are chemically stable. The structures of replacements are diversified: fulfillment of gaps, formation of edgings around the grains, selective replacement, forming of metacrystalls or metagrains. The thickness of forming edgings is not stable; boundaries have corrosion textures with penetration inside of replaced grain. The chemical composition of cations of forming disulfides depends upon the composition of primary mineral first of all, but it cannot be subject to this rule. For example, grains from placer of Bolshoy Khailyk river (Western Sayan) have a composition adequate to ruthenium (tab., No. 1) and are replaced by laurite more often (tab., No. 1-1). In Kuznetsky Alatau (placer of Talanovaya river) authors observed simultaneous replacement of osmium (with admixtures of Ru and Ir) (tab., No. 2) by laurite (tab., No. 2-1) and irarsite (tab., No. 2-2) along gaps. This fact is explained by more affinity of ruthenium to sulfur, then iridium and osmium to sulfur /2/. In conditions of low fugitivity of sulfur the edgings with more rare composition (Ir,Os,Ru)_3S_2 (tab., No. 3-1) are formed. It was observed by the authors on iridium (tab., No. 3) from placer of Sysim river (Eastern Sayan). The similar composition of phase was described by S.A.Toma and S.Murphy /6/. In placer of Talanovaya river (Kuznetsky Alatau) the edging of idealized composition Os_2S (tab., No. 4-1) are develops on the grain of Os-Ir-ruthenium (tab., No.4). It indicates deficit of sulfur in a solution. In case of increased concentration of arsenic the minerals of Os-Ir-Ru system (tab., No. 5) are replaced by diarsenides (anduoite - omeiite series) (tab., No. 5-1) or sulfoarsenides of these elements as it was observed in PGM from placer of Rudnaya river (Western Sayan). In the extremely rare cases at superposition of sulfurless and arsenicless solutions the replacement of alloys Os-Ir-Ru by exotic phases can happen. For example, authors find the grain of native iridium, which was heavily deformed and impregnated on microgaps by phases of generalized composition from Pt(Ni,Cu,Fe)_2 to Ir(Ni,Fe,Cu)_3 in placer of Bolshoy Khaylik river /7/. The forming of similar phases can be initiated by very specific conditions: the extremely reducing conditions, very low fugitivity of sulfur and oxygen, absence of other anion-forming elements, high activity of a nickel, iron and cooper. The similar phases were found in streak-schlieren chromitic ores in one massif of alpine-type ultramafic rocks of Koryak Highland /3/. Also rather rare replacement of platinum with the high contents of ruthenium and iridium (platruthenosmiridium by old nomenclature) (tab., No.6) by Pt-Fe alloys (tab., No.6-1). It was observed by authors in PGM from placer of Talanovaya river (Kuznetsky Alatau). In the system Pt-Fe most widespread placer-forming minerals are ferriferous platinum, tetraferroplatinum and isoferroplatinum. In placers that were investigated by the authors the Pt-Fe alloys most frequently is replaced by cuperite, which forms the various thickness edgings. It usual phenomenon in some cases becomes complicated by forming of narrow (first microns) intermittent band of high-standard gold on the boundary of cuperite and Pt-Fe alloy. Same edgings of gold round the grains of alloys with consequent overlap by a more broad band of cuperite were observed by S.A. Shcheka with the co-authors in PGM from placers of Far East /4/. According to these authors the forming of edgings of gold is connected to effect of gold-bearing solutions with low fugitivity of S and As on the Pt-Fe alloy. Hereinafter under the opinion of the quoted authors the concentrations of S and As have increased and cuperite or arsenides (sulfoarsenides) of platinum were formed. On ours opinion the forming of edgings of gold between PtS and Pt-Fe alloy may occur by two ways. At the first, the allocation of the bands of high-standard gold on the boundary Pt-Fe alloy and PtS was simultaneously with replacement. It is connected that the gold and silver was included in the crystalline of Pt-Fe alloys primary and at the time of replacement of this mineral these elements reduced to native phase because the entry to the lattice of cuperite is impossible. Such process can be presented as the following equation: (Pt,Pd,Au,Ag)_3Fe + 2S_2 =3(Pt,Pd)S + 3(Au,Ag)^0 + FeS There aren't crystallochemical prohibitions for such process. At the second, the gold from later solutions may penetrate deep into the grain through porous edging of cuperite and locate at the boundary of PtS and Pt-Fe alloy. Probability of these processes must be test by experiments. The cuperite edgings on Pt-Fe alloys are acquired by the band or metacrystalls of sperrilite later. It is connected to occurrence of arsenic in the system. A feature of the composition of these sperrylites is increased contents of those elements, which originally were included in the lattice of Pt-Fe alloys (Rh, Ir, Os). The complex replacements of Pt-Fe alloys were observed by the authors in placer Sysim river. Pt-Fe alloys from this placer are presented by small-sized isomeric grains and contain increased contents of rhodium (tab., No.7). This feature was reflected in phases of replacement. In one case the edgings of Rh-sperrylite thickness 15-30 microns rounds the grain of Pt-Fe alloy and between these minerals the thin intermittent band of mineral with adequate RhAs (cherepanovite?) composition is situated (tab., No.7-1). This association is complicated by formation of small-sized selections hollingworthite (tab., No.7-2). In the near-drift placers sperrylite occurs frequently. This mineral is brittle and havn't transported on distant distances, but it is chemically very stable phase. Nevertheless, it mineral is replaced by native platinum on the edgings frequently, that was observed by authors in placers of the rivers Coloromo, Danilovsky (Yenisei Ridge), Caragan (East Sayan) etc. This process can be finished by formation of the native platinum. According to T.L. Evstigneeva with co-authors /1/ the de-arsenization of sperrylite can happen only at rather high temperatures more 400^oC;. Therefore it cannot be attributed to process of low-temperature replacement in solid condition, and it is necessary to connect with temperature burning of sperrylite. The native platinum which was formed in it process differs from primary magmatic in high cleanness of composition and absence of any admixtures, except for As (tab., No.8, 8-1). References: 1.T.L.Evstigneeva, A.A.Kim, I.Ay.Nekrasov (1990) //About de-arsenization of sperrylite in nature. Mineralogical Zhurnal, vol.12, No3, pp.90-96 (in Russian). 2. A.A.Marakushev, N.I.Bezmen Thermodynamics of sulfides and oxides in connection with problems of ore-forming. - M., Nauka, 1972. - 230p (in Russian). 3. A.G.Mochalov, G.G.Dmitrenko, I.V.Zhernovskii, N.S.Rudashevskii (1985) New iridium-osmium-ruthenium type (solid solutions of rare platinum-group elements with iron) of platinum-group mineralization in chromium spinel-group minerals of alpine-type ultramafic rocks of Koryak Highland. - Zapiski Vses. Mineral. Obshch., 114, pp.544-554 (in Russian). 4. S.A.Shcheka, A.A.Vrzhosek, V.I. Sapin, N.I.Kiryukhina (1991) Trasformations of platinum-group minerals from Primor'ye placers. - Mineralogical Zhurnal, vol.13, No1, pp.31-40 (in Russian). 5. D.C.Harris, L.J.Cabri (1991) Nomenclature of platinum-group-element alloys: review and revision. - Canadian Mineralogist, vol.29, pp.231-237. 6. L.J.Cabri (ed.) (1978) Unnamed platinum-group minerals. In: Platinum-group elements: mineralogy, geology, recovery. - Canadian Institute of Mining and Metallurgy, Montreal, pp.177-195. 7. G.I.Shvedov, V.N.Knyazev Unnamed PGE Phases from Gold Placer Deposits of South Siberia, Russia. - 9th International Platinum Symposium, July 21-25, Billings, Montana, USA, 2002 (http://www.duke.edu/˜boudreau/IPS_Abstracts.htm).

A Multi-Purpose Data Dissemination Infrastructure for the Marine-Earth Observations

NASA Astrophysics Data System (ADS)

Hanafusa, Y.; Saito, H.; Kayo, M.; Suzuki, H.

2015-12-01

To open the data from a variety of observations, the Japan Agency for Marine-Earth Science and Technology (JAMSTEC) has developed a multi-purpose data dissemination infrastructure. Although many observations have been made in the earth science, all the data are not opened completely. We think data centers may provide researchers with a universal data dissemination service which can handle various kinds of observation data with little effort. For this purpose JAMSTEC Data Management Office has developed the "Information Catalog Infrastructure System (Catalog System)". This is a kind of catalog management system which can create, renew and delete catalogs (= databases) and has following features, - The Catalog System does not depend on data types or granularity of data records. - By registering a new metadata schema to the system, a new database can be created on the same system without sytem modification. - As web pages are defined by the cascading style sheets, databases have different look and feel, and operability. - The Catalog System provides databases with basic search tools; search by text, selection from a category tree, and selection from a time line chart. - For domestic users it creates the Japanese and English pages at the same time and has dictionary to control terminology and proper noun. As of August 2015 JAMSTEC operates 7 databases on the Catalog System. We expect to transfer existing databases to this system, or create new databases on it. In comparison with a dedicated database developed for the specific dataset, the Catalog System is suitable for the dissemination of small datasets, with minimum cost. Metadata held in the catalogs may be transfered to other metadata schema to exchange global databases or portals. Examples: JAMSTEC Data Catalog: http://www.godac.jamstec.go.jp/catalog/data_catalog/metadataList?lang=enJAMSTEC Document Catalog: http://www.godac.jamstec.go.jp/catalog/doc_catalog/metadataList?lang=en&tab=categoryResearch Information and Data Access Site of TEAMS: http://www.i-teams.jp/catalog/rias/metadataList?lang=en&tab=list

A New Interface for the Magnetics Information Consortium (MagIC) Paleo and Rock Magnetic Database

NASA Astrophysics Data System (ADS)

Jarboe, N.; Minnett, R.; Koppers, A. A. P.; Tauxe, L.; Constable, C.; Shaar, R.; Jonestrask, L.

2014-12-01

The Magnetic Information Consortium (MagIC) database (http://earthref.org/MagIC/) continues to improve the ease of uploading data, the creation of complex searches, data visualization, and data downloads for the paleomagnetic, geomagnetic, and rock magnetic communities. Data uploading has been simplified and no longer requires the use of the Excel SmartBook interface. Instead, properly formatted MagIC text files can be dragged-and-dropped onto an HTML 5 web interface. Data can be uploaded one table at a time to facilitate ease of uploading and data error checking is done online on the whole dataset at once instead of incrementally in an Excel Console. Searching the database has improved with the addition of more sophisticated search parameters and with the ability to use them in complex combinations. Searches may also be saved as permanent URLs for easy reference or for use as a citation in a publication. Data visualization plots (ARAI, equal area, demagnetization, Zijderveld, etc.) are presented with the data when appropriate to aid the user in understanding the dataset. Data from the MagIC database may be downloaded from individual contributions or from online searches for offline use and analysis in the tab delimited MagIC text file format. With input from the paleomagnetic, geomagnetic, and rock magnetic communities, the MagIC database will continue to improve as a data warehouse and resource.

Highly Automated Module Production Incorporating Advanced Light Management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perelli-Minetti, Michael; Roof, Kyle

2015-08-11

The objective was to enable a high volume, cost effective solution for increasing the amount of light captured by PV modules through utilization of an advanced Light Re-directing Film and to follow a phased approach to develop and implement this new technology in order to achieve an expected power gain of up to 12 watts per module. Full size PV modules were manufactured using a new Light Redirecting Film (LRF) material applied to two different areas of PV modules in order to increase the amount of light captured by the modules. One configuration involved applying thin strips of LRF filmmore » over the tabbing ribbon on the cells in order to redirect the light that is normally absorbed by the tabbing ribbon to the active areas of the cells. A second configuration involved applying thin strips of LRF film over the white spaces between cells within a module in order to capture some of the light that is normally reflected from the white areas back through the front glass of the modules. Significant power increases of 1.4% (3.9 watts) and 1.0% (3.2 watts), respectively, compared to standard PV modules were measured under standard test conditions. The performance of PV modules with LRF applied to the tabbing ribbon was modeled. The results showed that the power increase provided by LRF depended greatly on the angle of incident light with the optimum performance only occurring when the light was within a narrow range of being perpendicular to the solar module. The modeling showed that most of the performance gain would be lost when the angle of incident light was greater than 28 degrees off axis. This effect made the orientation of modules with LRF applied to tabbing ribbons very important as modules mounted in “portrait” mode were predicted to provide little to no power gain from LRF under real world conditions. Based on these results, modules with LRF on tabbing ribbons would have to be mounted in “landscape” mode to realize a performance advantage. In addition, modeling showed that under diffuse lighting conditions such as when the sky is overcast, there would be no significant performance advantage for modules with LRF. Modules were sent to an outside contractor to measure the power performance under different angles of incident light in order to validate the modeling results. The measured data agreed very well with the modeling predictions and showed that the power gain for modules with LRF applied to tabbing ribbons was completely lost at an angle of 25 degrees off of perpendicular. At even larger angles, the power was lower than standard modules. From 35 degrees to 55 degrees off axis, the power loss was about 1.4% or equal to the power gain at the optimum condition of perfectly on-axis light.« less

Modeling adsorption of cationic surfactants at air/water interface without using the Gibbs equation.

PubMed

Phan, Chi M; Le, Thu N; Nguyen, Cuong V; Yusa, Shin-ichi

2013-04-16

The Gibbs adsorption equation has been indispensable in predicting the surfactant adsorption at the interfaces, with many applications in industrial and natural processes. This study uses a new theoretical framework to model surfactant adsorption at the air/water interface without the Gibbs equation. The model was applied to two surfactants, C14TAB and C16TAB, to determine the maximum surface excesses. The obtained values demonstrated a fundamental change, which was verified by simulations, in the molecular arrangement at the interface. The new insights, in combination with recent discoveries in the field, expose the limitations of applying the Gibbs adsorption equation to cationic surfactants at the air/water interface.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oweis, Salah; Chagnon, Guy; Alunans, Peter

An electrochemical cell, including a jelly-roll type electrode stack, and a method for making such cell. The electrochemical cell includes folded electrode portions which form a plane recessed from the end of the electrode stack. The folded electrode portions are preferably formed by making pairs of slits in the electrode end and bending over the electrode portions between each pair of slits. The recessed plane forms a large area to which a current collection tab is subsequently connected. A coating may be applied to the folded portions of the electrode to further increase the contact area with the current collectionmore » tab by eliminating the slight variations in the recessed plane which are due to the overlap of the folded electrode portions.« less

Advanced Subsonic Technology (AST) Separate-Flow High-Bypass Ratio Nozzle Noise Reduction Program Test Report

NASA Technical Reports Server (NTRS)

Low, John K. C.; Schweiger, Paul S.; Premo, John W.; Barber, Thomas J.; Saiyed, Naseem (Technical Monitor)

2000-01-01

NASA s model-scale nozzle noise tests show that it is possible to achieve a 3 EPNdB jet noise reduction with inwardfacing chevrons and flipper-tabs installed on the primary nozzle and fan nozzle chevrons. These chevrons and tabs are simple devices and are easy to be incorporated into existing short duct separate-flow nonmixed nozzle exhaust systems. However, these devices are expected to cause some small amount of thrust loss relative to the axisymmetric baseline nozzle system. Thus, it is important to have these devices further tested in a calibrated nozzle performance test facility to quantify the thrust performances of these devices. The choice of chevrons or tabs for jet noise suppression would most likely be based on the results of thrust loss performance tests to be conducted by Aero System Engineering (ASE) Inc. It is anticipated that the most promising concepts identified from this program will be validated in full scale engine tests at both Pratt & Whitney and Allied-Signal, under funding from NASA s Engine Validation of Noise Reduction Concepts (EVNRC) programs. This will bring the technology readiness level to the point where the jet noise suppression concepts could be incorporated with high confidence into either new or existing turbofan engines having short-duct, separate-flow nacelles.

Socio-demographic correlates of sexual behaviours: a cross sectional survey of adolescents in Imo State secondary schools.

PubMed

Nwoke, E A; Okafor, J O; Chukwuocha, U M; Nworuh, B O

2011-03-01

The study was designed to determine the socio-demographic correlates of sexual behaviours of the adolescents in Imo State secondary schools. Three objectives and three hypotheses were formulated to guide the study. A cross sectional survey design was used and sample size was 3360 (2.2%) adolescents. A structured, validated and reliable questionnaire (r = 0.79) and focus group discussion were used as the instruments for data collection. Data analysis was done using mean and ANOVA statistics. The result generally, showed that the average sexual behaviours of the adolescents were below the decision mean of 2.50 and as such the adolescents were said to be sexually inactive. In Imo State secondary schools, various family sizes did not significantly influence the sexual behaviours of the adolescents (F-cal. 2.39, F-tab. 3.00 & P > 0.05), family structure significantly influenced their sexual behaviours (F-cal. 17.78, F-tab. 3.00 & P < 0.05) and different financial strengths influenced the adolescents sexual behaviours significantly (F-cal. 22.88, F-tab. 2.37 & P < 0.05. Of great worry is that unrestricted/uncontrolled adolescents sexual behaviours may expose them to sexually transmitted infections/HIV/AIDS, unwanted pregnancies, illegal abortion and dropping out of school. Thus comprehensive sex education was recommended.