Test/score/report: Simulation techniques for automating the test process

NASA Technical Reports Server (NTRS)

Hageman, Barbara H.; Sigman, Clayton B.; Koslosky, John T.

1994-01-01

A Test/Score/Report capability is currently being developed for the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) system which will automate testing of the Goddard Space Flight Center (GSFC) Payload Operations Control Center (POCC) and Mission Operations Center (MOC) software in three areas: telemetry decommutation, spacecraft command processing, and spacecraft memory load and dump processing. Automated computer control of the acceptance test process is one of the primary goals of a test team. With the proper simulation tools and user interface, the task of acceptance testing, regression testing, and repeatability of specific test procedures of a ground data system can be a simpler task. Ideally, the goal for complete automation would be to plug the operational deliverable into the simulator, press the start button, execute the test procedure, accumulate and analyze the data, score the results, and report the results to the test team along with a go/no recommendation to the test team. In practice, this may not be possible because of inadequate test tools, pressures of schedules, limited resources, etc. Most tests are accomplished using a certain degree of automation and test procedures that are labor intensive. This paper discusses some simulation techniques that can improve the automation of the test process. The TASS system tests the POCC/MOC software and provides a score based on the test results. The TASS system displays statistics on the success of the POCC/MOC system processing in each of the three areas as well as event messages pertaining to the Test/Score/Report processing. The TASS system also provides formatted reports documenting each step performed during the tests and the results of each step. A prototype of the Test/Score/Report capability is available and currently being used to test some POCC/MOC software deliveries. When this capability is fully operational it should greatly reduce the time necessary to test a POCC/MOC software delivery, as well as improve the quality of the test process.

7 CFR 28.956 - Prescribed fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., TESTING, AND STANDARDS Cotton Fiber and Processing Tests Fiber and Processing Tests § 28.956 Prescribed fees. Fees for fiber and processing tests shall be assessed as listed below: Item number and kind of test Fee per test 1.0Calibration cotton for use with High Volume Instruments, per 5 pound package: a. f...

7 CFR 28.956 - Prescribed fees.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., TESTING, AND STANDARDS Cotton Fiber and Processing Tests Fiber and Processing Tests § 28.956 Prescribed fees. Fees for fiber and processing tests shall be assessed as listed below: Item number and kind of test Fee per test 1.0Calibration cotton for use with High Volume Instruments, per 5 pound package: a. f...

Propulsion Test Handbook: MSFC and SSC. Draft 01

NASA Technical Reports Server (NTRS)

Hammond, John M.

2010-01-01

This Handbook was prepared to provide Propulsion Test Personnel a central source of fundamental reference material. The Testing Process, which is a three-part process of pre-test activities, testing, and post-test activities, involves a collaborative effort from the mechanical, electrical, safety, and environmental disciplines in the test environment. Pre-test activities, testing, and post-test activities processes will vary, per test requirements; however, the content of this Handbook should cover basic procedures and standards that are shared across Centers.

Transfer-appropriate processing in the testing effect.

PubMed

Veltre, Mary T; Cho, Kit W; Neely, James H

2015-01-01

The testing effect is the finding that taking a review test enhances performance on a final test relative to restudying the material. The present experiment investigated transfer-appropriate processing in the testing effect using semantic and orthographic cues to evoke conceptual and data-driven processing, respectively. After a study phase, subjects either restudied the material or took a cued-recall test consisting of half semantic and half orthographic cues in which the correct response was given as feedback. A final, cued-recall test consisted of the identical cue, or a new cue that was of the same type or different type of cue (semantic/orthographic or orthographic/semantic) as that used for that target in the review test. Testing enhanced memory in all conditions. When the review cues and final-test cues were identical, final recall was higher for semantic than orthographic cues. Consistent with test-based transfer-appropriate processing, memory performance improved as the review and final cues became more similar. These results suggest that the testing effect could potentially be caused by the episodic retrieval processes in a final memory test overlapping more with the episodic retrieval processes in a review test than with the encoding operations performed during restudy.

Improvement for enhancing effectiveness of universal power system (UPS) continuous testing process

NASA Astrophysics Data System (ADS)

Sriratana, Lerdlekha

2018-01-01

This experiment aims to enhance the effectiveness of the Universal Power System (UPS) continuous testing process of the Electrical and Electronic Institute by applying work scheduling and time study methods. Initially, the standard time of testing process has not been considered that results of unaccurate testing target and also time wasting has been observed. As monitoring and reducing waste time for improving the efficiency of testing process, Yamazumi chart and job scheduling theory (North West Corner Rule) were applied to develop new work process. After the improvements, the overall efficiency of the process possibly increased from 52.8% to 65.6% or 12.7%. Moreover, the waste time could reduce from 828.3 minutes to 653.6 minutes or 21%, while testing units per batch could increase from 3 to 4 units. Therefore, the number of testing units would increase from 12 units up to 20 units per month that also contribute to increase of net income of UPS testing process by 72%.

Generalization of the photo process window and its application to OPC test pattern design

NASA Astrophysics Data System (ADS)

Eisenmann, Hans; Peter, Kai; Strojwas, Andrzej J.

2003-07-01

From the early development phase up to the production phase, test pattern play a key role for microlithography. The requirement for test pattern is to represent the design well and to cover the space of all process conditions, e.g. to investigate the full process window and all other process parameters. This paper shows that the current state-of-the-art test pattern do not address these requirements sufficiently and makes suggestions for a better selection of test pattern. We present a new methodology to analyze an existing layout (e.g. logic library, test pattern or full chip) for critical layout situations which does not need precise process data. We call this method "process space decomposition", because it is aimed at decomposing the process impact to a layout feature into a sum of single independent contributions, the dimensions of the process space. This is a generalization of the classical process window, which examines defocus and exposure dependency of given test pattern, e.g. CD value of dense and isolated lines. In our process space we additionally define the dimensions resist effects, etch effects, mask error and misalignment, which describe the deviation of the printed silicon pattern from its target. We further extend it by the pattern space using a product based layout (library, full chip or synthetic test pattern). The criticality of pattern is defined by their deviation due to aerial image, their sensitivity to the respective dimension or several combinations of these. By exploring the process space for a given design, the method allows to find the most critical patterns independent of specific process parameters. The paper provides examples for different applications of the method: (1) selection of design oriented test pattern for lithography development (2) test pattern reduction in process characterization (3) verification/optimization of printability and performance of post processing procedures (like OPC) (4) creation of a sensitive process monitor.

SU-F-T-475: An Evaluation of the Overlap Between the Acceptance Testing and Commissioning Processes for Conventional Medical Linear Accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morrow, A; Rangaraj, D; Perez-Andujar, A

2016-06-15

Purpose: This work’s objective is to determine the overlap of processes, in terms of sub-processes and time, between acceptance testing and commissioning of a conventional medical linear accelerator and to evaluate the time saved by consolidating the two processes. Method: A process map for acceptance testing for medical linear accelerators was created from vendor documentation (Varian and Elekta). Using AAPM TG-106 and inhouse commissioning procedures, a process map was created for commissioning of said accelerators. The time to complete each sub-process in each process map was evaluated. Redundancies in the processes were found and the time spent on each weremore » calculated. Results: Mechanical testing significantly overlaps between the two processes - redundant work here amounts to 9.5 hours. Many beam non-scanning dosimetry tests overlap resulting in another 6 hours of overlap. Beam scanning overlaps somewhat - acceptance tests include evaluating PDDs and multiple profiles but for only one field size while commissioning beam scanning includes multiple field sizes and depths of profiles. This overlap results in another 6 hours of rework. Absolute dosimetry, field outputs, and end to end tests are not done at all in acceptance testing. Finally, all imaging tests done in acceptance are repeated in commissioning, resulting in about 8 hours of rework. The total time overlap between the two processes is about 30 hours. Conclusion: The process mapping done in this study shows that there are no tests done in acceptance testing that are not also recommended to do for commissioning. This results in about 30 hours of redundant work when preparing a conventional linear accelerator for clinical use. Considering these findings in the context of the 5000 linacs in the United states, consolidating acceptance testing and commissioning would have allowed for the treatment of an additional 25000 patients using no additional resources.« less

Incremental Validity of the Subscales of the Emotional Regulation Related to Testing Scale for Predicting Test Anxiety

ERIC Educational Resources Information Center

Feldt, Ronald; Lindley, Kyla; Louison, Rebecca; Roe, Allison; Timm, Megan; Utinkova, Nikola

2015-01-01

The Emotional Regulation Related to Testing Scale (ERT Scale) assesses strategies students use to regulate emotion related to academic testing. It has four dimensions: Cognitive Appraising Processes (CAP), Emotion-Focusing Processes (EFP), Task-Focusing Processes (TFP), and Regaining Task-Focusing Processes (RTFP). The study examined the factor…

Risk-based Strategy to Determine Testing Requirement for the Removal of Residual Process Reagents as Process-related Impurities in Bioprocesses.

PubMed

Qiu, Jinshu; Li, Kim; Miller, Karen; Raghani, Anil

2015-01-01

The purpose of this article is to recommend a risk-based strategy for determining clearance testing requirements of the process reagents used in manufacturing biopharmaceutical products. The strategy takes account of four risk factors. Firstly, the process reagents are classified into two categories according to their safety profile and history of use: generally recognized as safe (GRAS) and potential safety concern (PSC) reagents. The clearance testing of GRAS reagents can be eliminated because of their safe use historically and process capability to remove these reagents. An estimated safety margin (Se) value, a ratio of the exposure limit to the estimated maximum reagent amount, is then used to evaluate the necessity for testing the PSC reagents at an early development stage. The Se value is calculated from two risk factors, the starting PSC reagent amount per maximum product dose (Me), and the exposure limit (Le). A worst-case scenario is assumed to estimate the Me value, that is common. The PSC reagent of interest is co-purified with the product and no clearance occurs throughout the entire purification process. No clearance testing is required for this PSC reagent if its Se value is ≥1; otherwise clearance testing is needed. Finally, the point of the process reagent introduction to the process is also considered in determining the necessity of the clearance testing for process reagents. How to use the measured safety margin as a criterion for determining PSC reagent testing at process characterization, process validation, and commercial production stages are also described. A large number of process reagents are used in the biopharmaceutical manufacturing to control the process performance. Clearance testing for all of the process reagents will be an enormous analytical task. In this article, a risk-based strategy is described to eliminate unnecessary clearance testing for majority of the process reagents using four risk factors. The risk factors included in the strategy are (i) safety profile of the reagents, (ii) the starting amount of the process reagents used in the manufacturing process, (iii) the maximum dose of the product, and (iv) the point of introduction of the process reagents in the process. The implementation of the risk-based strategy can eliminate clearance testing for approximately 90% of the process reagents used in the manufacturing processes. This science-based strategy allows us to ensure patient safety and meet regulatory agency expectations throughout the product development life cycle. © PDA, Inc. 2015.

NASA Processes and Requirements for Conducting Human-in-the-Loop Closed Chamber Tests

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Montz, Michael E.

2004-01-01

NASA has specific processes and requirements that must be followed for tests involving human subjects to be conducted in a safe and effective manner. There are five distinct phases of test operations. Phase one, the test request phase, consists of those activities related to initiating, processing, reviewing, and evaluating the test request. Phase two, the test preparation phase consists of those activities related to planning, coordinating, documenting, and building up the test. Phase three, the test readiness phase consists of those activities related to verifying and reviewing the planned test operations. Phase four, the test activity phase, consists of all pretest operations, functional checkouts, emergency drills, and test operations. Phase five, the post test activity phase, consists of those activities performed once the test is completed, including briefings, documentation of anomalies, data reduction and archiving, and reporting. Project management processes must be followed for facility modifications and major test buildup, which include six phases: initiation and assessment, requirements evaluation, preliminary design, detailed design, use readiness review (URR) and acceptance. Compliance with requirements for safety and quality assurance are documented throughout the test buildup and test operation processes. Tests involving human subjects must be reviewed by the applicable Institutional Review Board (IRB).

Integrated Structural Analysis and Test Program

NASA Technical Reports Server (NTRS)

Kaufman, Daniel

2005-01-01

An integrated structural-analysis and structure-testing computer program is being developed in order to: Automate repetitive processes in testing and analysis; Accelerate pre-test analysis; Accelerate reporting of tests; Facilitate planning of tests; Improve execution of tests; Create a vibration, acoustics, and shock test database; and Integrate analysis and test data. The software package includes modules pertaining to sinusoidal and random vibration, shock and time replication, acoustics, base-driven modal survey, and mass properties and static/dynamic balance. The program is commanded by use of ActiveX controls. There is minimal need to generate command lines. Analysis or test files are selected by opening a Windows Explorer display. After selecting the desired input file, the program goes to a so-called analysis data process or test data process, depending on the type of input data. The status of the process is given by a Windows status bar, and when processing is complete, the data are reported in graphical, tubular, and matrix form.

The Effects of Test Trial and Processing Level on Immediate and Delayed Retention

ERIC Educational Resources Information Center

Chang, Sau Hou

2013-01-01

The purpose of the present study was to investigate the effects of test trial and processing level on immediate and delayed retention. Seventy-six college students were randomly assigned first to the single test and the repeated test trials, and then to the shallow processing level and the deep processing level to study forty stimulus words.…

High-impact strength acrylic denture base material processed by autoclave.

PubMed

Abdulwahhab, Salwan Sami

2013-10-01

To investigate the effect of two different cycles of autoclave processing on the transverse strength, impact strength, surface hardness and the porosity of high-impact strength acrylic denture base material. High Impact Acryl was the heat-cured acrylic denture base material included in the study. A total of 120 specimens were prepared, the specimens were grouped into: control groups in which high-impact strength acrylic resins processed by conventional water-bath processing technique (74°C for 1.5 h then boil for 30 min) and experimental groups in which high-impact strength acrylic resins processed by autoclave at 121°C, 210 kPa .The experimental groups were divided into (fast) groups for 15 min, and (slow) groups for 30 min. To study the effect of the autoclave processing (Tuttnauer 2540EA), four tests were conducted transverse strength (Instron universal testing machine), impact strength (Charpy tester), surface hardness (shore D), and porosity test. The results were analyzed to ANOVA and LSD test. In ANOVA test, there were highly significant differences between the results of the processing techniques in transverse, impact, hardness, and porosity test. The LSD test showed a significant difference between control and fast groups in transverse and hardness tests and a non-significant difference in impact test and a highly significant difference in porosity test; while, there were a highly significant differences between control and slow groups in all examined tests; finally, there were a non-significant difference between fast and slow groups in transverse and porosity tests and a highly significant difference in impact and hardness tests. In the autoclave processing technique, the slow (long) curing cycle improved the tested physical and mechanical properties as compared with the fast (short) curing cycle. The autoclave processing technique improved the tested physical and mechanical properties of High Impact Acryl. Copyright © 2013 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

21 CFR 113.83 - Establishing scheduled processes.

Code of Federal Regulations, 2011 CFR

2011-04-01

... procedures recognized by competent processing authorities. If incubation tests are necessary for process... the period of instituting the process. The incubation tests for confirmation of the scheduled... and associated incubation tests shall be prepared and shall be permanently retained by the person or...

Restless Legs Syndrome -- Self-Tests and Diagnosis

MedlinePlus

... Overview & Facts Symptoms & Causes Diagnosis & Self Tests Treatment Sleep Apnea Overview & Facts Symptoms & Risk Factors Self-Tests Diagnosis ... for a Sleep Study Testing Process & Results Home Sleep Apnea Testing Overview Testing Process & Results CPAP Overview Benefits ...

Using Workflow Modeling to Identify Areas to Improve Genetic Test Processes in the University of Maryland Translational Pharmacogenomics Project.

PubMed

Cutting, Elizabeth M; Overby, Casey L; Banchero, Meghan; Pollin, Toni; Kelemen, Mark; Shuldiner, Alan R; Beitelshees, Amber L

Delivering genetic test results to clinicians is a complex process. It involves many actors and multiple steps, requiring all of these to work together in order to create an optimal course of treatment for the patient. We used information gained from focus groups in order to illustrate the current process of delivering genetic test results to clinicians. We propose a business process model and notation (BPMN) representation of this process for a Translational Pharmacogenomics Project being implemented at the University of Maryland Medical Center, so that personalized medicine program implementers can identify areas to improve genetic testing processes. We found that the current process could be improved to reduce input errors, better inform and notify clinicians about the implications of certain genetic tests, and make results more easily understood. We demonstrate our use of BPMN to improve this important clinical process for CYP2C19 genetic testing in patients undergoing invasive treatment of coronary heart disease.

Using Workflow Modeling to Identify Areas to Improve Genetic Test Processes in the University of Maryland Translational Pharmacogenomics Project

PubMed Central

Cutting, Elizabeth M.; Overby, Casey L.; Banchero, Meghan; Pollin, Toni; Kelemen, Mark; Shuldiner, Alan R.; Beitelshees, Amber L.

2015-01-01

Delivering genetic test results to clinicians is a complex process. It involves many actors and multiple steps, requiring all of these to work together in order to create an optimal course of treatment for the patient. We used information gained from focus groups in order to illustrate the current process of delivering genetic test results to clinicians. We propose a business process model and notation (BPMN) representation of this process for a Translational Pharmacogenomics Project being implemented at the University of Maryland Medical Center, so that personalized medicine program implementers can identify areas to improve genetic testing processes. We found that the current process could be improved to reduce input errors, better inform and notify clinicians about the implications of certain genetic tests, and make results more easily understood. We demonstrate our use of BPMN to improve this important clinical process for CYP2C19 genetic testing in patients undergoing invasive treatment of coronary heart disease. PMID:26958179

The Rapid Integration and Test Environment: A Process for Achieving Software Test Acceptance

DTIC Science & Technology

2010-05-01

Test Environment : A Process for Achieving Software Test Acceptance 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S...mlif`v= 365= k^s^i=mlpqdo^ar^qb=p`elli= The Rapid Integration and Test Environment : A Process for Achieving Software Test Acceptance Patrick V...was awarded the Bronze Star. Introduction The Rapid Integration and Test Environment (RITE) initiative, implemented by the Program Executive Office

33 CFR 159.121 - Sewage processing test.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Sewage processing test. 159.121 Section 159.121 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION MARINE SANITATION DEVICES Design, Construction, and Testing § 159.121 Sewage processing test. (a...

Optimization and Improvement of Test Processes on a Production Line

NASA Astrophysics Data System (ADS)

Sujová, Erika; Čierna, Helena

2018-06-01

The paper deals with increasing processes efficiency at a production line of cylinder heads of engines in a production company operating in the automotive industry. The goal is to achieve improvement and optimization of test processes on a production line. It analyzes options for improving capacity, availability and productivity of processes of an output test by using modern technology available on the market. We have focused on analysis of operation times before and after optimization of test processes at specific production sections. By analyzing measured results we have determined differences in time before and after improvement of the process. We have determined a coefficient of efficiency OEE and by comparing outputs we have confirmed real improvement of the process of the output test of cylinder heads.

Millennials in the Fire Service: The Effectiveness of Fire Service Recruiting, Testing, and Retention

DTIC Science & Technology

2017-12-01

to effectively attract and retain millennials is in question. Stale marketing and static testing processes may be contributing to smaller hiring pools...ABSTRACT Modern-day fire service methods’ ability to effectively attract and retain millennials is in question. Stale marketing and static testing... Marketing of the Testing Process ..............................................................50  Table 6.  Type of Testing Process

A Systems Engineering Approach to Quality Assurance for Aerospace Testing

NASA Technical Reports Server (NTRS)

Shepherd, Christena C.

2014-01-01

On the surface, it appears that AS9100 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK) that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness. The Systems Engineering (SE) discipline is widely used in aerospace to ensure the progress from Stakeholder Expectations (the President, Congress, the taxpayers) to a successful, delivered product or service. Although this is well known, what is not well known is that these same SE processes are implemented in varying complexity, to prepare for and implement test projects that support research, development, verification and validation, qualification, and acceptance test projects. Although the test organization's terminology may vary from the SE terminology, and from one test service provider to another, the basic process is followed by successful, reliable testing organizations. For this analysis, NASA Procedural Requirements (NPR) 7123.1, NASA Systems Engineering Processes and Requirements is used to illustrate the SE processes that are used for major aerospace testing. Many of these processes are also implemented for smaller test projects, and this set of processes will also look familiar to those who have participated in launch site activation and flight demonstrations.

40 CFR 63.11980 - What are the test methods and calculation procedures for process wastewater?

Code of Federal Regulations, 2013 CFR

2013-07-01

... calculation procedures for process wastewater? 63.11980 Section 63.11980 Protection of Environment... § 63.11980 What are the test methods and calculation procedures for process wastewater? (a) Performance... performance tests during worst-case operating conditions for the PVCPU when the process wastewater treatment...

40 CFR 63.11980 - What are the test methods and calculation procedures for process wastewater?

Code of Federal Regulations, 2012 CFR

2012-07-01

... calculation procedures for process wastewater? 63.11980 Section 63.11980 Protection of Environment... § 63.11980 What are the test methods and calculation procedures for process wastewater? (a) Performance... performance tests during worst-case operating conditions for the PVCPU when the process wastewater treatment...

40 CFR 63.11980 - What are the test methods and calculation procedures for process wastewater?

Code of Federal Regulations, 2014 CFR

2014-07-01

... calculation procedures for process wastewater? 63.11980 Section 63.11980 Protection of Environment... § 63.11980 What are the test methods and calculation procedures for process wastewater? (a) Performance... performance tests during worst-case operating conditions for the PVCPU when the process wastewater treatment...

Sleep Eduction: Treatment & Therapy

MedlinePlus

... Overview & Facts Symptoms & Causes Diagnosis & Self Tests Treatment Sleep Apnea Overview & Facts Symptoms & Risk Factors Self-Tests Diagnosis ... for a Sleep Study Testing Process & Results Home Sleep Apnea Testing Overview Testing Process & Results CPAP Overview Benefits ...

The Effects of Test Trial and Processing Level on Immediate and Delayed Retention

ERIC Educational Resources Information Center

Chang, Sau Hou

2017-01-01

The purpose of the present study was to investigate the effects of test trial and processing level on immediate and delayed retention. A 2 × 2 × 2 mixed ANOVAs was used with two between-subject factors of test trial (single test, repeated test) and processing level (shallow, deep), and one within-subject factor of final recall (immediate,…

Find a Sleep Center Near You

MedlinePlus

... Overview & Facts Symptoms & Causes Diagnosis & Self Tests Treatment Sleep Apnea Overview & Facts Symptoms & Risk Factors Self-Tests Diagnosis ... for a Sleep Study Testing Process & Results Home Sleep Apnea Testing Overview Testing Process & Results CPAP Overview Benefits ...

End-of-fabrication CMOS process monitor

NASA Technical Reports Server (NTRS)

Buehler, M. G.; Allen, R. A.; Blaes, B. R.; Hannaman, D. J.; Lieneweg, U.; Lin, Y.-S.; Sayah, H. R.

1990-01-01

A set of test 'modules' for verifying the quality of a complementary metal oxide semiconductor (CMOS) process at the end of the wafer fabrication is documented. By electrical testing of specific structures, over thirty parameters are collected characterizing interconnects, dielectrics, contacts, transistors, and inverters. Each test module contains a specification of its purpose, the layout of the test structure, the test procedures, the data reduction algorithms, and exemplary results obtained from 3-, 2-, or 1.6-micrometer CMOS/bulk processes. The document is intended to establish standard process qualification procedures for Application Specific Integrated Circuits (ASIC's).

The Effects of Test Anxiety on Learning at Superficial and Deep Levels of Processing.

ERIC Educational Resources Information Center

Weinstein, Claire E.; And Others

1982-01-01

Using a deep-level processing strategy, low test-anxious college students performed significantly better than high test-anxious students in learning a paired-associate word list. Using a superficial-level processing strategy resulted in no significant difference in performance. A cognitive-attentional theory and test anxiety mechanisms are…

The beneficial effect of testing: an event-related potential study

PubMed Central

Bai, Cheng-Hua; Bridger, Emma K.; Zimmer, Hubert D.; Mecklinger, Axel

2015-01-01

The enhanced memory performance for items that are tested as compared to being restudied (the testing effect) is a frequently reported memory phenomenon. According to the episodic context account of the testing effect, this beneficial effect of testing is related to a process which reinstates the previously learnt episodic information. Few studies have explored the neural correlates of this effect at the time point when testing takes place, however. In this study, we utilized the ERP correlates of successful memory encoding to address this issue, hypothesizing that if the benefit of testing is due to retrieval-related processes at test then subsequent memory effects (SMEs) should resemble the ERP correlates of retrieval-based processing in their temporal and spatial characteristics. Participants were asked to learn Swahili-German word pairs before items were presented in either a testing or a restudy condition. Memory performance was assessed immediately and 1-day later with a cued recall task. Successfully recalling items at test increased the likelihood that items were remembered over time compared to items which were only restudied. An ERP subsequent memory contrast (later remembered vs. later forgotten tested items), which reflects the engagement of processes that ensure items are recallable the next day were topographically comparable with the ERP correlate of immediate recollection (immediately remembered vs. immediately forgotten tested items). This result shows that the processes which allow items to be more memorable over time share qualitatively similar neural correlates with the processes that relate to successful retrieval at test. This finding supports the notion that testing is more beneficial than restudying on memory performance over time because of its engagement of retrieval processes, such as the re-encoding of actively retrieved memory representations. PMID:26441577

Development of environmentally conscious cleaning process for leadless chip carrier assemblies. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, B.E.

1995-04-01

A cross-functional team of process, product, quality, material, and design lab engineers was assembled to develop an environmentally friendly cleaning process for leadless chip carrier assemblies (LCCAs). Using flush and filter testing, Auger surface analysis, GC-Mass spectrophotometry, production yield results, and electrical testing results over an extended testing period, the team developed an aqueous cleaning process for LCCAs. The aqueous process replaced the Freon vapor degreasing/ultrasonic rinse process.

Taking the Test Taker's Perspective: Response Process and Test Motivation in Multidimensional Forced-Choice Versus Rating Scale Instruments.

PubMed

Sass, Rachelle; Frick, Susanne; Reips, Ulf-Dietrich; Wetzel, Eunike

2018-03-01

The multidimensional forced-choice (MFC) format has been proposed as an alternative to the rating scale (RS) response format. However, it is unclear how changing the response format may affect the response process and test motivation of participants. In Study 1, we investigated the MFC response process using the think-aloud technique. In Study 2, we compared test motivation between the RS format and different versions of the MFC format (presenting 2, 3, 4, and 5 items simultaneously). The response process to MFC item blocks was similar to the RS response process but involved an additional step of weighing the items within a block against each other. The RS and MFC response format groups did not differ in their test motivation. Thus, from the test taker's perspective, the MFC format is somewhat more demanding to respond to, but this does not appear to decrease test motivation.

Impact of Educational Level on Performance on Auditory Processing Tests.

PubMed

Murphy, Cristina F B; Rabelo, Camila M; Silagi, Marcela L; Mansur, Letícia L; Schochat, Eliane

2016-01-01

Research has demonstrated that a higher level of education is associated with better performance on cognitive tests among middle-aged and elderly people. However, the effects of education on auditory processing skills have not yet been evaluated. Previous demonstrations of sensory-cognitive interactions in the aging process indicate the potential importance of this topic. Therefore, the primary purpose of this study was to investigate the performance of middle-aged and elderly people with different levels of formal education on auditory processing tests. A total of 177 adults with no evidence of cognitive, psychological or neurological conditions took part in the research. The participants completed a series of auditory assessments, including dichotic digit, frequency pattern and speech-in-noise tests. A working memory test was also performed to investigate the extent to which auditory processing and cognitive performance were associated. The results demonstrated positive but weak correlations between years of schooling and performance on all of the tests applied. The factor "years of schooling" was also one of the best predictors of frequency pattern and speech-in-noise test performance. Additionally, performance on the working memory, frequency pattern and dichotic digit tests was also correlated, suggesting that the influence of educational level on auditory processing performance might be associated with the cognitive demand of the auditory processing tests rather than auditory sensory aspects itself. Longitudinal research is required to investigate the causal relationship between educational level and auditory processing skills.

Recommendations for elaboration, transcultural adaptation and validation process of tests in Speech, Hearing and Language Pathology.

PubMed

Pernambuco, Leandro; Espelt, Albert; Magalhães, Hipólito Virgílio; Lima, Kenio Costa de

2017-06-08

to present a guide with recommendations for translation, adaptation, elaboration and process of validation of tests in Speech and Language Pathology. the recommendations were based on international guidelines with a focus on the elaboration, translation, cross-cultural adaptation and validation process of tests. the recommendations were grouped into two Charts, one of them with procedures for translation and transcultural adaptation and the other for obtaining evidence of validity, reliability and measures of accuracy of the tests. a guide with norms for the organization and systematization of the process of elaboration, translation, cross-cultural adaptation and validation process of tests in Speech and Language Pathology was created.

21 CFR 212.60 - What requirements apply to the laboratories where I test components, in-process materials, and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... I test components, in-process materials, and finished PET drug products? 212.60 Section 212.60 Food... finished PET drug products? (a) Testing procedures. Each laboratory used to conduct testing of components, in-process materials, and finished PET drug products must have and follow written procedures for the...

21 CFR 212.60 - What requirements apply to the laboratories where I test components, in-process materials, and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... I test components, in-process materials, and finished PET drug products? 212.60 Section 212.60 Food... materials, and finished PET drug products? (a) Testing procedures. Each laboratory used to conduct testing of components, in-process materials, and finished PET drug products must have and follow written...

21 CFR 212.60 - What requirements apply to the laboratories where I test components, in-process materials, and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... I test components, in-process materials, and finished PET drug products? 212.60 Section 212.60 Food... finished PET drug products? (a) Testing procedures. Each laboratory used to conduct testing of components, in-process materials, and finished PET drug products must have and follow written procedures for the...

21 CFR 212.60 - What requirements apply to the laboratories where I test components, in-process materials, and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... I test components, in-process materials, and finished PET drug products? 212.60 Section 212.60 Food... finished PET drug products? (a) Testing procedures. Each laboratory used to conduct testing of components, in-process materials, and finished PET drug products must have and follow written procedures for the...

21 CFR 212.60 - What requirements apply to the laboratories where I test components, in-process materials, and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... I test components, in-process materials, and finished PET drug products? 212.60 Section 212.60 Food... finished PET drug products? (a) Testing procedures. Each laboratory used to conduct testing of components, in-process materials, and finished PET drug products must have and follow written procedures for the...

Laboratory testing in primary care: A systematic review of health IT impacts.

PubMed

Maillet, Éric; Paré, Guy; Currie, Leanne M; Raymond, Louis; Ortiz de Guinea, Ana; Trudel, Marie-Claude; Marsan, Josianne

2018-08-01

Laboratory testing in primary care is a fundamental process that supports patient management and care. Any breakdown in the process may alter clinical information gathering and decision-making activities and can lead to medical errors and potential adverse outcomes for patients. Various information technologies are being used in primary care with the goal to support the process, maximize patient benefits and reduce medical errors. However, the overall impact of health information technologies on laboratory testing processes has not been evaluated. To synthesize the positive and negative impacts resulting from the use of health information technology in each phase of the laboratory 'total testing process' in primary care. We conducted a systematic review. Databases including Medline, PubMed, CINAHL, Web of Science and Google Scholar were searched. Studies eligible for inclusion reported empirical data on: 1) the use of a specific IT system, 2) the impacts of the systems to support the laboratory testing process, and were conducted in 3) primary care settings (including ambulatory care and primary care offices). Our final sample consisted of 22 empirical studies which were mapped to a framework that outlines the phases of the laboratory total testing process, focusing on phases where medical errors may occur. Health information technology systems support several phases of the laboratory testing process, from ordering the test to following-up with patients. This is a growing field of research with most studies focusing on the use of information technology during the final phases of the laboratory total testing process. The findings were largely positive. Positive impacts included easier access to test results by primary care providers, reduced turnaround times, and increased prescribed tests based on best practice guidelines. Negative impacts were reported in several studies: paper-based processes employed in parallel to the electronic process increased the potential for medical errors due to clinicians' cognitive overload; systems deemed not reliable or user-friendly hampered clinicians' performance; and organizational issues arose when results tracking relied on the prescribers' memory. The potential of health information technology lies not only in the exchange of health information, but also in knowledge sharing among clinicians. This review has underscored the important role played by cognitive factors, which are critical in the clinician's decision-making, the selection of the most appropriate tests, correct interpretation of the results and efficient interventions. By providing the right information, at the right time to the right clinician, many IT solutions adequately support the laboratory testing process and help primary care clinicians make better decisions. However, several technological and organizational barriers require more attention to fully support the highly fragmented and error-prone process of laboratory testing. Copyright © 2018 Elsevier B.V. All rights reserved.

Identifying failure in a tree network of a parallel computer

DOEpatents

Archer, Charles J.; Pinnow, Kurt W.; Wallenfelt, Brian P.

2010-08-24

Methods, parallel computers, and products are provided for identifying failure in a tree network of a parallel computer. The parallel computer includes one or more processing sets including an I/O node and a plurality of compute nodes. For each processing set embodiments include selecting a set of test compute nodes, the test compute nodes being a subset of the compute nodes of the processing set; measuring the performance of the I/O node of the processing set; measuring the performance of the selected set of test compute nodes; calculating a current test value in dependence upon the measured performance of the I/O node of the processing set, the measured performance of the set of test compute nodes, and a predetermined value for I/O node performance; and comparing the current test value with a predetermined tree performance threshold. If the current test value is below the predetermined tree performance threshold, embodiments include selecting another set of test compute nodes. If the current test value is not below the predetermined tree performance threshold, embodiments include selecting from the test compute nodes one or more potential problem nodes and testing individually potential problem nodes and links to potential problem nodes.

Testing military grade magnetics (transformers, inductors and coils).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Engineers and designers are constantly searching for test methods to qualify or 'prove-in' new designs. In the High Reliability world of military parts, design test, qualification tests, in process tests and product characteristic tests, become even more important. The use of in process and function tests has been adopted as a way of demonstrating that parts will operate correctly and survive its 'use' environments. This paper discusses various types of tests to qualify the magnetic components - the current carrying capability of coils, a next assembly 'as used' test, a corona test and inductance at temperature test. Each of thesemore » tests addresses a different potential failure on a component. The entire process from design to implementation is described.« less

CRT image recording evaluation

NASA Technical Reports Server (NTRS)

1971-01-01

Performance capabilities and limitations of a fiber optic coupled line scan CRT image recording system were investigated. The test program evaluated the following components: (1). P31 phosphor CRT with EMA faceplate; (2). P31 phosphor CRT with clear clad faceplate; (3). Type 7743 semi-gloss dry process positive print paper; (4). Type 777 flat finish dry process positive print paper; (5). Type 7842 dry process positive film; and (6). Type 1971 semi-gloss wet process positive print paper. Detailed test procedures used in each test are provided along with a description of each test, the test data, and an analysis of the results.

Using Automation to Improve the Flight Software Testing Process

NASA Technical Reports Server (NTRS)

ODonnell, James R., Jr.; Andrews, Stephen F.; Morgenstern, Wendy M.; Bartholomew, Maureen O.; McComas, David C.; Bauer, Frank H. (Technical Monitor)

2001-01-01

One of the critical phases in the development of a spacecraft attitude control system (ACS) is the testing of its flight software. The testing (and test verification) of ACS flight software requires a mix of skills involving software, attitude control, data manipulation, and analysis. The process of analyzing and verifying flight software test results often creates a bottleneck which dictates the speed at which flight software verification can be conducted. In the development of the Microwave Anisotropy Probe (MAP) spacecraft ACS subsystem, an integrated design environment was used that included a MAP high fidelity (HiFi) simulation, a central database of spacecraft parameters, a script language for numeric and string processing, and plotting capability. In this integrated environment, it was possible to automate many of the steps involved in flight software testing, making the entire process more efficient and thorough than on previous missions. In this paper, we will compare the testing process used on MAP to that used on previous missions. The software tools that were developed to automate testing and test verification will be discussed, including the ability to import and process test data, synchronize test data and automatically generate HiFi script files used for test verification, and an automated capability for generating comparison plots. A summary of the perceived benefits of applying these test methods on MAP will be given. Finally, the paper will conclude with a discussion of re-use of the tools and techniques presented, and the ongoing effort to apply them to flight software testing of the Triana spacecraft ACS subsystem.

Using Automation to Improve the Flight Software Testing Process

NASA Technical Reports Server (NTRS)

ODonnell, James R., Jr.; Morgenstern, Wendy M.; Bartholomew, Maureen O.

2001-01-01

One of the critical phases in the development of a spacecraft attitude control system (ACS) is the testing of its flight software. The testing (and test verification) of ACS flight software requires a mix of skills involving software, knowledge of attitude control, and attitude control hardware, data manipulation, and analysis. The process of analyzing and verifying flight software test results often creates a bottleneck which dictates the speed at which flight software verification can be conducted. In the development of the Microwave Anisotropy Probe (MAP) spacecraft ACS subsystem, an integrated design environment was used that included a MAP high fidelity (HiFi) simulation, a central database of spacecraft parameters, a script language for numeric and string processing, and plotting capability. In this integrated environment, it was possible to automate many of the steps involved in flight software testing, making the entire process more efficient and thorough than on previous missions. In this paper, we will compare the testing process used on MAP to that used on other missions. The software tools that were developed to automate testing and test verification will be discussed, including the ability to import and process test data, synchronize test data and automatically generate HiFi script files used for test verification, and an automated capability for generating comparison plots. A summary of the benefits of applying these test methods on MAP will be given. Finally, the paper will conclude with a discussion of re-use of the tools and techniques presented, and the ongoing effort to apply them to flight software testing of the Triana spacecraft ACS subsystem.

Impact of Salt Waste Processing Facility Streams on the Nitric-Glycolic Flowsheet in the Chemical Processing Cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C.

An evaluation of the previous Chemical Processing Cell (CPC) testing was performed to determine whether the planned concurrent operation, or “coupled” operations, of the Defense Waste Processing Facility (DWPF) with the Salt Waste Processing Facility (SWPF) has been adequately covered. Tests with the nitricglycolic acid flowsheet, which were both coupled and uncoupled with salt waste streams, included several tests that required extended boiling times. This report provides the evaluation of previous testing and the testing recommendation requested by Savannah River Remediation. The focus of the evaluation was impact on flammability in CPC vessels (i.e., hydrogen generation rate, SWPF solvent components,more » antifoam degradation products) and processing impacts (i.e., acid window, melter feed target, rheological properties, antifoam requirements, and chemical composition).« less

Testing Strategies for Model-Based Development

NASA Technical Reports Server (NTRS)

Heimdahl, Mats P. E.; Whalen, Mike; Rajan, Ajitha; Miller, Steven P.

2006-01-01

This report presents an approach for testing artifacts generated in a model-based development process. This approach divides the traditional testing process into two parts: requirements-based testing (validation testing) which determines whether the model implements the high-level requirements and model-based testing (conformance testing) which determines whether the code generated from a model is behaviorally equivalent to the model. The goals of the two processes differ significantly and this report explores suitable testing metrics and automation strategies for each. To support requirements-based testing, we define novel objective requirements coverage metrics similar to existing specification and code coverage metrics. For model-based testing, we briefly describe automation strategies and examine the fault-finding capability of different structural coverage metrics using tests automatically generated from the model.

Observations on the Use of SCAN To Identify Children at Risk for Central Auditory Processing Disorder.

ERIC Educational Resources Information Center

Emerson, Maria F.; And Others

1997-01-01

The SCAN: A Screening Test for Auditory Processing Disorders was administered to 14 elementary children with a history of otitis media and 14 typical children, to evaluate the validity of the test in identifying children with central auditory processing disorder. Another experiment found that test results differed based on the testing environment…

Improving preanalytic processes using the principles of lean production (Toyota Production System).

PubMed

Persoon, Thomas J; Zaleski, Sue; Frerichs, Janice

2006-01-01

The basic technologies used in preanalytic processes for chemistry tests have been mature for a long time, and improvements in preanalytic processes have lagged behind improvements in analytic and postanalytic processes. We describe our successful efforts to improve chemistry test turnaround time from a central laboratory by improving preanalytic processes, using existing resources and the principles of lean production. Our goal is to report 80% of chemistry tests in less than 1 hour and to no longer recognize a distinction between expedited and routine testing. We used principles of lean production (the Toyota Production System) to redesign preanalytic processes. The redesigned preanalytic process has fewer steps and uses 1-piece flow to move blood samples through the accessioning, centrifugation, and aliquoting processes. Median preanalytic processing time was reduced from 29 to 19 minutes, and the laboratory met the goal of reporting 80% of chemistry results in less than 1 hour for 11 consecutive months.

Using Dispersed Modes During Model Correlation

NASA Technical Reports Server (NTRS)

Stewart, Eric C.; Hathcock, Megan L.

2017-01-01

The model correlation process for the modal characteristics of a launch vehicle is well established. After a test, parameters within the nominal model are adjusted to reflect structural dynamics revealed during testing. However, a full model correlation process for a complex structure can take months of man-hours and many computational resources. If the analyst only has weeks, or even days, of time in which to correlate the nominal model to the experimental results, then the traditional correlation process is not suitable. This paper describes using model dispersions to assist the model correlation process and decrease the overall cost of the process. The process creates thousands of model dispersions from the nominal model prior to the test and then compares each of them to the test data. Using mode shape and frequency error metrics, one dispersion is selected as the best match to the test data. This dispersion is further improved by using a commercial model correlation software. In the three examples shown in this paper, this dispersion based model correlation process performs well when compared to models correlated using traditional techniques and saves time in the post-test analysis.

Investigation of the Factors Affecting the Pre-Test Effect in National Curriculum Science Assessment Development in England

ERIC Educational Resources Information Center

Pyle, Katie; Jones, Emily; Williams, Chris; Morrison, Jo

2009-01-01

Background: All national curriculum tests in England are pre-tested as part of the development process. Differences in pupil performance between pre-test and live test are consistently found. This difference has been termed the pre-test effect. Understanding the pre-test effect is essential in the test development and selection processes and in…

Summary of Granulation Matrix Testing for the Plutonium Immobilization Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herman, C.C.

2001-10-19

In FY00, a matrix for process development testing was created to identify those items related to the ceramic process that had not been fully developed or tested and to help identify variables that needed to be tested. This matrix, NMTP/IP-99-003, was jointly created between LLNL and SRTC and was issued to all affected individuals. The matrix was also used to gauge the progress of the development activities. As part of this matrix, several series of tests were identified for the granulation process. This summary provides the data and results from the granulation testing. The results of the granulation matrix testingmore » were used to identify the baseline process for testing in the PuCTF with cold surrogates in B241 at LLNL.« less

Molybdenum-99 Isotope Production Preparation at Sandia National Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carson, S.D.; Longley, S.W.; McDonald, M.J.

`Q&c M. J. McDonald, S. D. Carson, S. W. Longley, E. J. Parma, M. E. Vern `~ I@ .,., Sandia National Laboratories*, P. .0. Box 5800, Albuquerque, NM, 8 W? 1$ tl?;:q `f. (3 . 8 /'~ Abstract This report was prepared as an account of work sponsored byanagency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, make any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its usemore » would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. loading on the Cintichem targets. These tests were designed to gain process knowledge prior to processing an irradiated target. The chemical separation tests were performed in a fime hood During cold testing, several tests were performed on individual components of the process to complete, a series of `hot' tests was designed to process irradiated targets. These were designed to optimize the process, identify problems prior to processing higher inventory targets, and to the shielded containment box (SCB). Table 1 is a summary of the tests performed prior to the Test Target Power Post irradiation Total inventory 99M0 inventory (kW)/ Irradiation decay (hrs) (TBq*) /decay (TBq)/decay Time (hrs) inventory (TBq) inventory(TBq) in the processing boxes as color comparisons. Product quality control testing was conducted for all the tests and the results were compared to The production process generates a high activity acidic liquid waste. Several waste stabilization processing box. The cement, in addition to stabilizing the waste, neutralized the waste resulting The processing hardware and fixtures were developed in parallel to the cold tests and tested in a that expected during processing. During processing, precautions will be taken to minimize the Island incident. The facility consisted of shielded glove boxes, unshielded glove box lines and the the facility for production operations; the glove box lines and shielded glove boxes, all the new configuration will have six windows, four extraction boxes and a waste packaging box on the shielding. The walls and windows of the processing boxes will have the equivalent 150 of the purification box will be considerably less than the processing boxes with dose being from only `gMo. The increased wall thickness will reduce the dose levels to boxes will have under the box transport systems to move material into and out of the boxes. prior to FDA requiring process validation and, consequently, had not pertlormed a process« less

Automated plasma control with optical emission spectroscopy

NASA Astrophysics Data System (ADS)

Ward, P. P.

Plasma etching and desmear processes for printed wiring board (PWB) manufacture are difficult to predict and control. Non-uniformity of most plasma processes and sensitivity to environmental changes make it difficult to maintain process stability from day to day. To assure plasma process performance, weight loss coupons or post-plasma destructive testing must be used. These techniques are not real-time methods however, and do not allow for immediate diagnosis and process correction. These tests often require scrapping some fraction of a batch to insure the integrity of the rest. Since these tests verify a successful cycle with post-plasma diagnostics, poor test results often determine that a batch is substandard and the resulting parts unusable. These tests are a costly part of the overall fabrication cost. A more efficient method of testing would allow for constant monitoring of plasma conditions and process control. Process anomalies should be detected and corrected before the parts being treated are damaged. Real time monitoring would allow for instantaneous corrections. Multiple site monitoring would allow for process mapping within one system or simultaneous monitoring of multiple systems. Optical emission spectroscopy conducted external to the plasma apparatus would allow for this sort of multifunctional analysis without perturbing the glow discharge. In this paper, optical emission spectroscopy for non-intrusive, in situ process control will be explored along with applications of this technique to for process control, failure analysis and endpoint determination in PWB manufacture.

Collaborative Testing: Cognitive and Interpersonal Processes Related to Enhanced Test Performance

ERIC Educational Resources Information Center

Kapitanoff, Susan H.

2009-01-01

Research has demonstrated that collaborative testing, working on tests in groups, leads to improved test scores but the mechanism by which this occurs has not been specified. Three factors were proposed as mediators: cognitive processes, interpersonal interactions and reduced test-anxiety. Thirty-three students completed a multiple-choice exam…

Does Testing Impair Relational Processing? Failed Attempts to Replicate the Negative Testing Effect

ERIC Educational Resources Information Center

Rawson, Katherine A.; Wissman, Kathryn T.; Vaughn, Kalif E.

2015-01-01

Recent research on testing effects (i.e., practice tests are more effective than restudy for enhancing subsequent memory) has focused on explaining when and why testing enhances memory. Of particular interest for present purposes, Zaromb and Roediger (2010) reported evidence that testing effects in part reflect enhanced relational processing,…

Unconscious memory bias in depression: perceptual and conceptual processes.

PubMed

Watkins, P C; Martin, C K; Stern, L D

2000-05-01

Mood-congruent memory (MCM) bias in depression was investigated using 4 different implicit memory tests. Two of the implicit tests were perceptually driven, and 2 were conceptually driven. Depressed participants and nondepressed controls were assigned to 1 of 4 implicit memory tests after studying positive and negative adjectives. Results showed no MCM bias in the perceptually driven tests. MCM was demonstrated in 1 of the conceptually driven tests, but only for adjectives that were conceptually encoded. Results support the theory that mood-congruent processes in depression are limited to conceptual processing. However, activation of conceptual processes may not be sufficient for demonstrating mood congruency.

A process dissociation approach to objective-projective test score interrelationships.

PubMed

Bornstein, Robert F

2002-02-01

Even when self-report and projective measures of a given trait or motive both predict theoretically related features of behavior, scores on the 2 tests correlate modestly with each other. This article describes a process dissociation framework for personality assessment, derived from research on implicit memory and learning, which can resolve these ostensibly conflicting results. Research on interpersonal dependency is used to illustrate 3 key steps in the process dissociation approach: (a) converging behavioral predictions, (b) modest test score intercorrelations, and (c) delineation of variables that differentially affect self-report and projective test scores. Implications of the process dissociation framework for personality assessment and test development are discussed.

Presentation format effects in a levels-of-processing task.

PubMed

Foos, Paul W; Goolkasian, Paula

2008-01-01

Three experiments were conducted to examine better performance in long-term memory when stimulus items are pictures or spoken words compared to printed words. Hypotheses regarding the allocation of attention to printed words, the semantic link between pictures and processing, and a rich long-term representation for pictures were tested. Using levels-of-processing tasks eliminated format effects when no memory test was expected and processing was deep (El), and when study and test formats did not match (E3). Pictures produced superior performance when a memory test was expected (El & 2) and when study and test formats were the same (E3). Results of all experiments support the attenuation of attention model and that picture superiority is due to a more direct access to semantic processing and a richer visual code. General principles to guide the processing of stimulus information are discussed.

On Fast Post-Processing of Global Positioning System Simulator Truth Data and Receiver Measurements and Solutions Data

NASA Technical Reports Server (NTRS)

Kizhner, Semion; Day, John H. (Technical Monitor)

2000-01-01

Post-processing of data, related to a GPS receiver test in a GPS simulator and test facility, is an important step towards qualifying a receiver for space flight. Although the GPS simulator provides all the parameters needed to analyze a simulation, as well as excellent analysis tools on the simulator workstation, post-processing is not a GPS simulator or receiver function alone, and it must be planned as a separate pre-flight test program requirement. A GPS simulator is a critical resource, and it is desirable to move off the pertinent test data from the simulator as soon as a test is completed. The receiver and simulator databases are used to extract the test data files for postprocessing. These files are then usually moved from the simulator and receiver systems to a personal computer (PC) platform, where post-processing is done typically using PC-based commercial software languages and tools. Because of commercial software systems generality their functions are notoriously slow and more than often are the bottleneck even for short duration simulator-based tests. There is a need to do post-processing faster and within an hour after test completion, including all required operations on the simulator and receiver to prepare and move off the post-processing files. This is especially significant in order to use the previous test feedback for the next simulation setup or to run near back-to-back simulation scenarios. Solving the post-processing timing problem is critical for a pre-flight test program success. Towards this goal an approach was developed that allows to speed-up post-processing by an order of a magnitude. It is based on improving the post-processing bottleneck function algorithm using a priory information that is specific to a GPS simulation application and using only the necessary volume of truth data. The presented postprocessing scheme was used in support of a few successful space flight missions carrying GPS receivers.

High density electronic circuit and process for making

DOEpatents

Morgan, William P.

1999-01-01

High density circuits with posts that protrude beyond one surface of a substrate to provide easy mounting of devices such as integrated circuits. The posts also provide stress relief to accommodate differential thermal expansion. The process allows high interconnect density with fewer alignment restrictions and less wasted circuit area than previous processes. The resulting substrates can be test platforms for die testing and for multi-chip module substrate testing. The test platform can contain active components and emulate realistic operational conditions, replacing shorts/opens net testing.

40 CFR 60.255 - Performance tests and other compliance requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Preparation and Processing Plants § 60.255 Performance tests and other compliance requirements. (a) An owner... within a 60-minute period of) PM performance tests. (c) If any affected coal processing and conveying...) when the coal preparation and processing plant is in operation. Each observation must be recorded as...

40 CFR 60.255 - Performance tests and other compliance requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Preparation and Processing Plants § 60.255 Performance tests and other compliance requirements. (a) An owner... within a 60-minute period of) PM performance tests. (c) If any affected coal processing and conveying...) when the coal preparation and processing plant is in operation. Each observation must be recorded as...

40 CFR 60.255 - Performance tests and other compliance requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Preparation and Processing Plants § 60.255 Performance tests and other compliance requirements. (a) An owner... within a 60-minute period of) PM performance tests. (c) If any affected coal processing and conveying...) when the coal preparation and processing plant is in operation. Each observation must be recorded as...

40 CFR 60.255 - Performance tests and other compliance requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Preparation and Processing Plants § 60.255 Performance tests and other compliance requirements. (a) An owner... within a 60-minute period of) PM performance tests. (c) If any affected coal processing and conveying...) when the coal preparation and processing plant is in operation. Each observation must be recorded as...

The study of human higher mental functions as they relate to neurophysiological processes and personal characteristics

NASA Astrophysics Data System (ADS)

Runnova, Anastasiya; Zhuravlev, Maxim; Kulanin, Roman; Protasov, Pavel; Hramov, Alexander; Koronovskii, Alexey

2018-02-01

In this paper we study the correlation between the neurophysiological processes and personal characteristics arising in the processes of human higher mental functions. We find that the activity of the brain correlates with the results of psychological tests (according to the Cattell test). Experimental studies and math processing are described for operation design with the registration of human multi-channel EEG data in two phases (the processes of passive wakefulness (background) and special psychological testing (active phase)).

Processes of conscious and unconscious memory: evidence from current research on dissociation of memories within a test.

PubMed

Cheng, Chao-Ming; Huang, Chin-Lan

2011-01-01

The processes of conscious memory (CM) and unconscious memory (UM) are explored, based on the results of the current and previous studies in which the 2 forms of memory within a test were separated by either the process dissociation or metacognition-based dissociation procedure. The results assessing influences of shallow and deep processing, association, and self-generation on CM in explicit and implicit tests are taken as evidence that CM in a test is driven not only conceptually but also by the driving nature of the test, and CM benefits from an encoding condition to the extent that information processing for CM recapitulates that engaged in the encoding condition.Those influences on UM in explicit and implicit tests are taken to support the view that UM in a test is driven by the nature of the test itself, and UM benefits from an encoding condition to the extent that the cognitive environments at test and at study match to activate the same type of information (e.g., visual, lexical, or semantic) about memory items or the same content of a preexisting association or categorical structure.

Error-proofing test system of industrial components based on image processing

NASA Astrophysics Data System (ADS)

Huang, Ying; Huang, Tao

2018-05-01

Due to the improvement of modern industrial level and accuracy, conventional manual test fails to satisfy the test standards of enterprises, so digital image processing technique should be utilized to gather and analyze the information on the surface of industrial components, so as to achieve the purpose of test. To test the installation parts of automotive engine, this paper employs camera to capture the images of the components. After these images are preprocessed including denoising, the image processing algorithm relying on flood fill algorithm is used to test the installation of the components. The results prove that this system has very high test accuracy.

A rigorous approach to facilitate and guarantee the correctness of the genetic testing management in human genome information systems.

PubMed

Araújo, Luciano V; Malkowski, Simon; Braghetto, Kelly R; Passos-Bueno, Maria R; Zatz, Mayana; Pu, Calton; Ferreira, João E

2011-12-22

Recent medical and biological technology advances have stimulated the development of new testing systems that have been providing huge, varied amounts of molecular and clinical data. Growing data volumes pose significant challenges for information processing systems in research centers. Additionally, the routines of genomics laboratory are typically characterized by high parallelism in testing and constant procedure changes. This paper describes a formal approach to address this challenge through the implementation of a genetic testing management system applied to human genome laboratory. We introduced the Human Genome Research Center Information System (CEGH) in Brazil, a system that is able to support constant changes in human genome testing and can provide patients updated results based on the most recent and validated genetic knowledge. Our approach uses a common repository for process planning to ensure reusability, specification, instantiation, monitoring, and execution of processes, which are defined using a relational database and rigorous control flow specifications based on process algebra (ACP). The main difference between our approach and related works is that we were able to join two important aspects: 1) process scalability achieved through relational database implementation, and 2) correctness of processes using process algebra. Furthermore, the software allows end users to define genetic testing without requiring any knowledge about business process notation or process algebra. This paper presents the CEGH information system that is a Laboratory Information Management System (LIMS) based on a formal framework to support genetic testing management for Mendelian disorder studies. We have proved the feasibility and showed usability benefits of a rigorous approach that is able to specify, validate, and perform genetic testing using easy end user interfaces.

A rigorous approach to facilitate and guarantee the correctness of the genetic testing management in human genome information systems

PubMed Central

2011-01-01

Background Recent medical and biological technology advances have stimulated the development of new testing systems that have been providing huge, varied amounts of molecular and clinical data. Growing data volumes pose significant challenges for information processing systems in research centers. Additionally, the routines of genomics laboratory are typically characterized by high parallelism in testing and constant procedure changes. Results This paper describes a formal approach to address this challenge through the implementation of a genetic testing management system applied to human genome laboratory. We introduced the Human Genome Research Center Information System (CEGH) in Brazil, a system that is able to support constant changes in human genome testing and can provide patients updated results based on the most recent and validated genetic knowledge. Our approach uses a common repository for process planning to ensure reusability, specification, instantiation, monitoring, and execution of processes, which are defined using a relational database and rigorous control flow specifications based on process algebra (ACP). The main difference between our approach and related works is that we were able to join two important aspects: 1) process scalability achieved through relational database implementation, and 2) correctness of processes using process algebra. Furthermore, the software allows end users to define genetic testing without requiring any knowledge about business process notation or process algebra. Conclusions This paper presents the CEGH information system that is a Laboratory Information Management System (LIMS) based on a formal framework to support genetic testing management for Mendelian disorder studies. We have proved the feasibility and showed usability benefits of a rigorous approach that is able to specify, validate, and perform genetic testing using easy end user interfaces. PMID:22369688

Habituation, Response to Novelty, and Dishabituation in Human Infants: Tests of a Dual-Process Theory of Visual Attention.

ERIC Educational Resources Information Center

Kaplan, Peter S.; Werner, John S.

1986-01-01

Tests infants' dual-process performance (a process mediating response decrements called habituation and a state-dependent process mediating response increments called sensitization) on visual habituation-dishabituation tasks. (HOD)

Transfer-appropriate processing in recognition memory: perceptual and conceptual effects on recognition memory depend on task demands.

PubMed

Parks, Colleen M

2013-07-01

Research examining the importance of surface-level information to familiarity in recognition memory tasks is mixed: Sometimes it affects recognition and sometimes it does not. One potential explanation of the inconsistent findings comes from the ideas of dual process theory of recognition and the transfer-appropriate processing framework, which suggest that the extent to which perceptual fluency matters on a recognition test depends in large part on the task demands. A test that recruits perceptual processing for discrimination should show greater perceptual effects and smaller conceptual effects than standard recognition, similar to the pattern of effects found in perceptual implicit memory tasks. This idea was tested in the current experiment by crossing a levels of processing manipulation with a modality manipulation on a series of recognition tests that ranged from conceptual (standard recognition) to very perceptually demanding (a speeded recognition test with degraded stimuli). Results showed that the levels of processing effect decreased and the effect of modality increased when tests were made perceptually demanding. These results support the idea that surface-level features influence performance on recognition tests when they are made salient by the task demands. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Task difficulty differentially affects two measures of processing load: the pupil response during sentence processing and delayed cued recall of the sentences.

PubMed

Zekveld, Adriana A; Festen, Joost M; Kramer, Sophia E

2013-08-01

In this study, the authors assessed the influence of masking level (29% or 71% sentence perception) and test modality on the processing load during language perception as reflected by the pupil response. In addition, the authors administered a delayed cued stimulus recall test to examine whether processing load affected the encoding of the stimuli in memory. Participants performed speech and text reception threshold tests, during which the pupil response was measured. In the cued recall test, the first half of correctly perceived sentences was presented, and participants were asked to complete the sentences. Reading and listening span tests of working memory capacity were presented as well. Regardless of test modality, the pupil response indicated higher processing load in the 29% condition than in the 71% correct condition. Cued recall was better for the 29% condition. The consistent effect of masking level on the pupil response during listening and reading support the validity of the pupil response as a measure of processing load during language perception. The absent relation between pupil response and cued recall may suggest that cued recall is not directly related to processing load, as reflected by the pupil response.

[Does the Fragmented Images Test measure locally oriented visual processing in autism spectrum disorders?].

PubMed

Scheurich, Armin; Fellgiebel, Andreas; Müller, Mattias J; Poustka, Fritz; Bölte, Sven

2010-03-01

The cognitive phenotype of autism spectrum disorders (ASD) is characterized among other things by local processing (weak central coherence). It was examined whether a test that measures identification of fragmented pictures (FBT) is able to seize this preference for local processing. The FBT performance of 15 patients with ASD, 16 with depression, 16 with schizophrenia and of 16 control subjects was compared. In addition, two tests well known to be sensitive to local processing were assessed, namely the Embedded Figures Test (EFT) and the Block Design Test (BDT). ASD patients demonstrated a preference for local processing. Difficulties in global processing, or more specifically in gestalt perception (FBT), were accompanied by good performance on the EFT and BDT as expected. Controlling for age and nonverbal intelligence (ANCOVA) reduced differences to trends. However, the calculation of difference scores (i.e., subtraction of FBT from EFT performance) resulted in significant differences between ASD and control groups even after controlling for of age and intelligence. The FBT is a suitable exploratory test of local visual processing in ASD. In particular, a difference criterion can be generated (FBT vs. EFT) that discriminates between ASD and clinical as well as healthy control groups.

Performance tests.

PubMed Central

Wetherell, A

1996-01-01

This paper discusses the use of psychological performance tests to assess the effects of environmental stressors. The large number and the variety of performance tests are illustrated, and the differences between performance tests and other psychological tests are described in terms of their design, construction, use, and purpose. The stressor emphasis is on the effects of drugs since that is where most performance tests have found their main application, although other stressors, e.g., fatigue, toxic chemicals, are mentioned where appropriate. Diazepam is used as an example. There is no particular performance emphasis since the tests are intended to have wide applicability. However, vehicle-driving performance is discussed because it has been the subject of a great deal of research and is probably one of the most important areas of application. Performance tests are discussed in terms of the four main underlying models--factor analysis, general information processing, multiple resource and strategy models, and processing-stage models--and in terms of their psychometric properties--sensitivity, reliability, and content, criterion, construct, and face validity. Some test taxonomies are presented. Standardization is also discussed with reference to the reaction time, mathematical processing, memory search, spatial processing, unstable tracking, verbal processing, and dual task tests used in the AGARD STRES battery. Some comments on measurement strengths and appropriate study designs and methods are included. PMID:9182033

Communication with patients during the prenatal testing procedure: an explorative qualitative study.

PubMed

van Zwieten, Myra; Willems, Dick; Knegt, Lia; Leschot, Nico

2006-10-01

While generally two phases of prenatal genetic counseling are distinguished, i.e. pre- and post-test counseling, we revealed a third form of communication during the testing procedure. The content of this intermediate communication was explored. A secondary analysis was performed on data obtained in another observational study, which was focussed on how indefinite testing results are clarified. Thirteen testing trajectories in which communication with parents took place during the testing procedure were further analysed. In the majority of cases the content of intermediate communication was similar to the content of pre-test counseling. In four cases the content was different, because the communication involved the parents in decision-making about a testing result, which was still being processed. Communication in (prenatal) genetic testing is not always restricted to separate phases, but can be an ongoing process occurring parallel to, and sometimes even intertwined with, the testing process. The advocated model of shared decision-making might work better once it is determined if the decision concerns the area wherein the provider is the expert, or the patient. Further research into the process of continuing decision-making could clarify how providers' and patients' responsibilities regarding the diagnostic process are distributed. Meanwhile, the possible occurrence of continuous decision-making should be mentioned in (prenatal) genetic counseling.

Paradigms of Evaluation in Natural Language Processing: Field Linguistics for Glass Box Testing

ERIC Educational Resources Information Center

Cohen, Kevin Bretonnel

2010-01-01

Although software testing has been well-studied in computer science, it has received little attention in natural language processing. Nonetheless, a fully developed methodology for glass box evaluation and testing of language processing applications already exists in the field methods of descriptive linguistics. This work lays out a number of…

The Promise of NLP and Speech Processing Technologies in Language Assessment

ERIC Educational Resources Information Center

Chapelle, Carol A.; Chung, Yoo-Ree

2010-01-01

Advances in natural language processing (NLP) and automatic speech recognition and processing technologies offer new opportunities for language testing. Despite their potential uses on a range of language test item types, relatively little work has been done in this area, and it is therefore not well understood by test developers, researchers or…

Cognitive Process Modeling of Spatial Ability: The Assembling Objects Task

ERIC Educational Resources Information Center

Ivie, Jennifer L.; Embretson, Susan E.

2010-01-01

Spatial ability tasks appear on many intelligence and aptitude tests. Although the construct validity of spatial ability tests has often been studied through traditional correlational methods, such as factor analysis, less is known about the cognitive processes involved in solving test items. This study examines the cognitive processes involved in…

Eye-Tracking as a Tool in Process-Oriented Reading Test Validation

ERIC Educational Resources Information Center

Solheim, Oddny Judith; Uppstad, Per Henning

2011-01-01

The present paper addresses the continuous need for methodological reflection on how to validate inferences made on the basis of test scores. Validation is a process that requires many lines of evidence. In this article we discuss the potential of eye tracking methodology in process-oriented reading test validation. Methodological considerations…

40 CFR 63.145 - Process wastewater provisions-test methods and procedures to determine compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Process wastewater provisions-test... Operations, and Wastewater § 63.145 Process wastewater provisions—test methods and procedures to determine... analytical method for wastewater which has that compound as a target analyte. (7) Treatment using a series of...

40 CFR 63.145 - Process wastewater provisions-test methods and procedures to determine compliance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Process wastewater provisions-test... Operations, and Wastewater § 63.145 Process wastewater provisions—test methods and procedures to determine... analytical method for wastewater which has that compound as a target analyte. (7) Treatment using a series of...

Test Review: Wagner, R. K., Torgesen, J. K., Rashotte, C. A., & Pearson, N. A., "Comprehensive Test of Phonological Processing-2nd Ed. (CTOPP-2)." Austin, Texas: Pro-Ed

ERIC Educational Resources Information Center

Dickens, Rachel H.; Meisinger, Elizabeth B.; Tarar, Jessica M.

2015-01-01

The Comprehensive Test of Phonological Processing-Second Edition (CTOPP-2; Wagner, Torgesen, Rashotte, & Pearson, 2013) is a norm-referenced test that measures phonological processing skills related to reading for individuals aged 4 to 24. According to its authors, the CTOPP-2 may be used to identify individuals who are markedly below their…

The Cognitive Processing of Candidates during Reading Tests: Evidence from Eye-Tracking

ERIC Educational Resources Information Center

Bax, Stephen

2013-01-01

The research described in this article investigates test takers' cognitive processing while completing onscreen IELTS (International English Language Testing System) reading test items. The research aims, among other things, to contribute to our ability to evaluate the cognitive validity of reading test items (Glaser, 1991; Field, in press). The…

Development of dynamic Bayesian models for web application test management

NASA Astrophysics Data System (ADS)

Azarnova, T. V.; Polukhin, P. V.; Bondarenko, Yu V.; Kashirina, I. L.

2018-03-01

The mathematical apparatus of dynamic Bayesian networks is an effective and technically proven tool that can be used to model complex stochastic dynamic processes. According to the results of the research, mathematical models and methods of dynamic Bayesian networks provide a high coverage of stochastic tasks associated with error testing in multiuser software products operated in a dynamically changing environment. Formalized representation of the discrete test process as a dynamic Bayesian model allows us to organize the logical connection between individual test assets for multiple time slices. This approach gives an opportunity to present testing as a discrete process with set structural components responsible for the generation of test assets. Dynamic Bayesian network-based models allow us to combine in one management area individual units and testing components with different functionalities and a direct influence on each other in the process of comprehensive testing of various groups of computer bugs. The application of the proposed models provides an opportunity to use a consistent approach to formalize test principles and procedures, methods used to treat situational error signs, and methods used to produce analytical conclusions based on test results.

CATS, continuous automated testing of seismological, hydroacoustic, and infrasound (SHI) processing software.

NASA Astrophysics Data System (ADS)

Brouwer, Albert; Brown, David; Tomuta, Elena

2017-04-01

To detect nuclear explosions, waveform data from over 240 SHI stations world-wide flows into the International Data Centre (IDC) of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO), located in Vienna, Austria. A complex pipeline of software applications processes this data in numerous ways to form event hypotheses. The software codebase comprises over 2 million lines of code, reflects decades of development, and is subject to frequent enhancement and revision. Since processing must run continuously and reliably, software changes are subjected to thorough testing before being put into production. To overcome the limitations and cost of manual testing, the Continuous Automated Testing System (CATS) has been created. CATS provides an isolated replica of the IDC processing environment, and is able to build and test different versions of the pipeline software directly from code repositories that are placed under strict configuration control. Test jobs are scheduled automatically when code repository commits are made. Regressions are reported. We present the CATS design choices and test methods. Particular attention is paid to how the system accommodates the individual testing of strongly interacting software components that lack test instrumentation.

Central auditory processing disorder (CAPD) in children with specific language impairment (SLI). Central auditory tests.

PubMed

Dlouha, Olga; Novak, Alexej; Vokral, Jan

2007-06-01

The aim of this project is to use central auditory tests for diagnosis of central auditory processing disorder (CAPD) in children with specific language impairment (SLI), in order to confirm relationship between speech-language impairment and central auditory processing. We attempted to establish special dichotic binaural tests in Czech language modified for younger children. Tests are based on behavioral audiometry using dichotic listening (different auditory stimuli that presented to each ear simultaneously). The experimental tasks consisted of three auditory measures (test 1-3)-dichotic listening of two-syllable words presented like binaural interaction tests. Children with SLI are unable to create simple sentences from two words that are heard separately but simultaneously. Results in our group of 90 pre-school children (6-7 years old) confirmed integration deficit and problems with quality of short-term memory. Average rate of success of children with specific language impairment was 56% in test 1, 64% in test 2 and 63% in test 3. Results of control group: 92% in test 1, 93% in test 2 and 92% in test 3 (p<0.001). Our results indicate the relationship between disorders of speech-language perception and central auditory processing disorders.

High density electronic circuit and process for making

DOEpatents

Morgan, W.P.

1999-06-29

High density circuits with posts that protrude beyond one surface of a substrate to provide easy mounting of devices such as integrated circuits are disclosed. The posts also provide stress relief to accommodate differential thermal expansion. The process allows high interconnect density with fewer alignment restrictions and less wasted circuit area than previous processes. The resulting substrates can be test platforms for die testing and for multi-chip module substrate testing. The test platform can contain active components and emulate realistic operational conditions, replacing shorts/opens net testing. 8 figs.

21 CFR 113.83 - Establishing scheduled processes.

Code of Federal Regulations, 2010 CFR

2010-04-01

... shall be performed according to procedures recognized by competent processing authorities. If incubation... actual commercial production runs during the period of instituting the process. The incubation tests for... of the process and associated incubation tests shall be prepared and shall be permanently retained by...

Comparison of seven kinds of drinking water treatment processes to enhance organic material removal: a pilot test.

PubMed

Chen, Chao; Zhang, Xiaojian; He, Wenjie; Lu, Wei; Han, Hongda

2007-08-15

Organic matter in source water has presented many challenges in the field of water purification, especially for conventional treatment. A two-year-long pilot test comparing water treatment processes was conducted to enhance organic matter removal. The tested process combinations included the conventional process, conventional plus advanced treatment, pre-oxidation plus conventional process and pre-oxidation plus conventional plus advanced treatment. The efficiency of each kind of process was assayed with the comprehensive indices of COD(Mn), TOC, UV(254), AOC, BDOC, THMs, and HAAs and their formation potential. The results showed that the combination of the conventional process and O(3)-BAC provides integrated removal of organic matter and meets the required standards. It is the best performing treatment tested in this investigation for treating polluted source water in China. Moreover, much attention should be paid to organic removal before disinfection to control DBP formation and preserve biostability. This paper also reports the range of efficiency of each unit process to calculate the total efficiency of different process combinations in order to help choose the appropriate water treatment process.

Marking Tests to Certify Part Identification Processes for Use in Low Earth Orbit

NASA Technical Reports Server (NTRS)

Roxby, D. L.

2015-01-01

The primary purpose for the MISSE marking tests was to define Data Matrix symbol marking processes that will remain readable after exposure to Low Earth Orbit environments. A wide range of different Data Matrix symbol marking processes and materials, including some still under development, were evaluated. The samples flown on MISSE 1 and 2 were in orbit for 3 years and 348 days, MISSE 3 and 4 were in orbit for 1 year and 15 days, MISSE 6 was in orbit for 1 year and 130 days, and MISSE 8 was in orbit for 2 years and 55 days. The initial MISSE marking tests clearly reflected that intrusive marking processes can be successfully used for this purpose. All of the intrusive marking processes tested exceeded program expectations and met 100 percent of the principle investigators objectives. However, subsequent tests demonstrated that some additive marking processes will also satisfy the requirements. This was an unexpected result.

Influence of Eye Movements, Auditory Perception, and Phonemic Awareness in the Reading Process

ERIC Educational Resources Information Center

Megino-Elvira, Laura; Martín-Lobo, Pilar; Vergara-Moragues, Esperanza

2016-01-01

The authors' aim was to analyze the relationship of eye movements, auditory perception, and phonemic awareness with the reading process. The instruments used were the King-Devick Test (saccade eye movements), the PAF test (auditory perception), the PFC (phonemic awareness), the PROLEC-R (lexical process), the Canals reading speed test, and the…

Stochastic Processes as True-Score Models for Highly Speeded Mental Tests.

ERIC Educational Resources Information Center

Moore, William E.

The previous theoretical development of the Poisson process as a strong model for the true-score theory of mental tests is discussed, and additional theoretical properties of the model from the standpoint of individual examinees are developed. The paper introduces the Erlang process as a family of test theory models and shows in the context of…

CPAS Preflight Drop Test Analysis Process

NASA Technical Reports Server (NTRS)

Englert, Megan E.; Bledsoe, Kristin J.; Romero, Leah M.

2015-01-01

Throughout the Capsule Parachute Assembly System (CPAS) drop test program, the CPAS Analysis Team has developed a simulation and analysis process to support drop test planning and execution. This process includes multiple phases focused on developing test simulations and communicating results to all groups involved in the drop test. CPAS Engineering Development Unit (EDU) series drop test planning begins with the development of a basic operational concept for each test. Trajectory simulation tools include the Flight Analysis and Simulation Tool (FAST) for single bodies, and the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) simulation for the mated vehicle. Results are communicated to the team at the Test Configuration Review (TCR) and Test Readiness Review (TRR), as well as at Analysis Integrated Product Team (IPT) meetings in earlier and intermediate phases of the pre-test planning. The ability to plan and communicate efficiently with rapidly changing objectives and tight schedule constraints is a necessity for safe and successful drop tests.

Investigating the Construct Measured by Banked Gap-Fill Items: Evidence from Eye-Tracking

ERIC Educational Resources Information Center

McCray, Gareth; Brunfaut, Tineke

2018-01-01

This study investigates test-takers' processing while completing banked gap-fill tasks, designed to test reading proficiency, in order to test theoretically based expectations about the variation in cognitive processes of test-takers across levels of performance. Twenty-eight test-takers' eye traces on 24 banked gap-fill items (on six tasks) were…

A Process for Reviewing and Evaluating Generated Test Items

ERIC Educational Resources Information Center

Gierl, Mark J.; Lai, Hollis

2016-01-01

Testing organization needs large numbers of high-quality items due to the proliferation of alternative test administration methods and modern test designs. But the current demand for items far exceeds the supply. Test items, as they are currently written, evoke a process that is both time-consuming and expensive because each item is written,…

Alternative Vocabularies in the Test Validity Literature

ERIC Educational Resources Information Center

Markus, Keith A.

2016-01-01

Justification of testing practice involves moving from one state of knowledge about the test to another. Theories of test validity can (a) focus on the beginning of the process, (b) focus on the end, or (c) encompass the entire process. Analyses of four case studies test and illustrate three claims: (a) restrictions on validity entail a supplement…

An initial investigation into the validity of a computer-based auditory processing assessment (Feather Squadron).

PubMed

Barker, Matthew D; Purdy, Suzanne C

2016-01-01

This research investigates a novel method for identifying and measuring school-aged children with poor auditory processing through a tablet computer. Feasibility and test-retest reliability are investigated by examining the percentage of Group 1 participants able to complete the tasks and developmental effects on performance. Concurrent validity was investigated against traditional tests of auditory processing using Group 2. There were 847 students aged 5 to 13 years in group 1, and 46 aged 5 to 14 years in group 2. Some tasks could not be completed by the youngest participants. Significant correlations were found between results of most auditory processing areas assessed by the Feather Squadron test and traditional auditory processing tests. Test-retest comparisons indicated good reliability for most of the Feather Squadron assessments and some of the traditional tests. The results indicate the Feather Squadron assessment is a time-efficient, feasible, concurrently valid, and reliable approach for measuring auditory processing in school-aged children. Clinically, this may be a useful option for audiologists when performing auditory processing assessments as it is a relatively fast, engaging, and easy way to assess auditory processing abilities. Research is needed to investigate further the construct validity of this new assessment by examining the association between performance on Feather Squadron and objective evoked potential, lesion studies, and/or functional imaging measures of auditory function.

Investigating the mixture and subdivision of perceptual and conceptual processing in Japanese memory tests.

PubMed

Gabeza, R

1995-03-01

The dual nature of the Japanese writing system was used to investigate two assumptions of the processing view of memory transfer: (1) that both perceptual and conceptual processing can contribute to the same memory test (mixture assumption) and (2) that both can be broken into more specific processes (subdivision assumption). Supporting the mixture assumption, a word fragment completion test based on ideographic kanji characters (kanji fragment completion test) was affected by both perceptual (hiragana/kanji script shift) and conceptual (levels-of-processing) study manipulations kanji fragments, because it did not occur with the use of meaningless hiragana fragments. The mixture assumption is also supported by an effect of study script on an implicit conceptual test (sentence completion), and the subdivision assumption is supported by a crossover dissociation between hiragana and kanji fragment completion as a function of study script.

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR THE BENCH STEAM REFORMER TEST

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2010-08-03

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Fluid Bed Steam Reformer testing. The type, quantity and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluid bed steam reformer (FBSR). A determination of the adequacy of the FBSR process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the FBSR process is to select archived waste samples from the 222-S Laboratory that will be used to test the FBSR process. Analyses of the selected samples will be required to confirm the samples meet the testing criteria.« less

Response to an Abnormal Ovarian Cancer Screening Test Result: Test of the Social Cognitive Processing and Cognitive Social Health Information Processing Models

PubMed Central

Andrykowski, Michael A.; Pavlik, Edward J.

2009-01-01

All cancer screening tests produce a proportion of abnormal results requiring follow-up. Consequently, the cancer screening setting is a natural laboratory for examining psychological and behavioral response to a threatening health-related event. This study tested hypotheses derived from the Social Cognitive Processing and Cognitive-Social Health Information Processing models in trying to understand response to an abnormal ovarian cancer (OC) screening test result. Women (n=278) receiving an abnormal screening test result a mean of 7 weeks earlier were assessed prior to a repeat screening test intended to clarify their previous abnormal result. Measures of disposition (optimism, informational coping style), social environment (social support and constraint), emotional processing, distress, and benefit finding were obtained. Regression analyses indicated greater distress was associated with greater social constraint and emotional processing and a monitoring coping style in women with a family history of OC. Distress was unrelated to social support. Greater benefit finding was associated with both greater social constraint and support and greater distress. The primacy of social constraint in accounting for both benefit-finding and distress was noteworthy and warrants further research on the role of social constraint in adaptation to stressful events. PMID:20419561

[The balanced scorecard used as a management tool in a clinical laboratory: internal business processes indicators].

PubMed

Salinas La Casta, Maria; Flores Pardo, Emilio; Uris Selles, Joaquín

2009-01-01

to propose a set of indicators as a management tool for a clinical laboratory, by using the balanced scorecard internal business processes perspective. indicators proposed are obtained from different sources; external proficiency testing of the Valencia Community Government, by means of internal surveys and laboratory information system registers. One year testing process proportion indicators results are showed. internal management indicators are proposed (process, appropriateness and proficiency testing). The process indicators results show gradual improvement since its establishment. after one years of using a conceptually solid Balanced Scorecard Internal business processes perspective indicators, the obtained results validate the usefulness as a laboratory management tool.

Linking microbial community structure and microbial processes: An empirical and conceptual overview

USGS Publications Warehouse

Bier, R.L.; Bernhardt, Emily S.; Boot, Claudia M.; Graham, Emily B.; Hall, Edward K.; Lennon, Jay T.; Nemergut, Diana R.; Osborne, Brooke B.; Ruiz-Gonzalez, Clara; Schimel, Joshua P.; Waldrop, Mark P.; Wallenstein, Matthew D.

2015-01-01

A major goal of microbial ecology is to identify links between microbial community structure and microbial processes. Although this objective seems straightforward, there are conceptual and methodological challenges to designing studies that explicitly evaluate this link. Here, we analyzed literature documenting structure and process responses to manipulations to determine the frequency of structure-process links and whether experimental approaches and techniques influence link detection. We examined nine journals (published 2009–13) and retained 148 experimental studies measuring microbial community structure and processes. Many qualifying papers (112 of 148) documented structure and process responses, but few (38 of 112 papers) reported statistically testing for a link. Of these tested links, 75% were significant and typically used Spearman or Pearson's correlation analysis (68%). No particular approach for characterizing structure or processes was more likely to produce significant links. Process responses were detected earlier on average than responses in structure or both structure and process. Together, our findings suggest that few publications report statistically testing structure-process links. However, when links are tested for they often occur but share few commonalities in the processes or structures that were linked and the techniques used for measuring them.

Waveform Generator Signal Processing Software

DOT National Transportation Integrated Search

1988-09-01

This report describes the software that was developed to process test waveforms that were recorded by crash test data acquisition systems. The test waveforms are generated by an electronic waveform generator developed by MGA Research Corporation unde...

9 CFR 310.25 - Contamination with microorganisms; process control verification criteria and testing; pathogen...

Code of Federal Regulations, 2010 CFR

2010-01-01

... CERTIFICATION POST-MORTEM INSPECTION § 310.25 Contamination with microorganisms; process control verification... testing. (1) Each official establishment that slaughters livestock must test for Escherichia coli Biotype... poultry, shall test the type of livestock or poultry slaughtered in the greatest number. The establishment...

9 CFR 310.25 - Contamination with microorganisms; process control verification criteria and testing; pathogen...

Code of Federal Regulations, 2014 CFR

2014-01-01

... CERTIFICATION POST-MORTEM INSPECTION § 310.25 Contamination with microorganisms; process control verification... testing. (1) Each official establishment that slaughters livestock must test for Escherichia coli Biotype... poultry, shall test the type of livestock or poultry slaughtered in the greatest number. The establishment...

9 CFR 310.25 - Contamination with microorganisms; process control verification criteria and testing; pathogen...

Code of Federal Regulations, 2013 CFR

2013-01-01

... CERTIFICATION POST-MORTEM INSPECTION § 310.25 Contamination with microorganisms; process control verification... testing. (1) Each official establishment that slaughters livestock must test for Escherichia coli Biotype... poultry, shall test the type of livestock or poultry slaughtered in the greatest number. The establishment...

9 CFR 310.25 - Contamination with microorganisms; process control verification criteria and testing; pathogen...

Code of Federal Regulations, 2012 CFR

2012-01-01

... CERTIFICATION POST-MORTEM INSPECTION § 310.25 Contamination with microorganisms; process control verification... testing. (1) Each official establishment that slaughters livestock must test for Escherichia coli Biotype... poultry, shall test the type of livestock or poultry slaughtered in the greatest number. The establishment...

9 CFR 310.25 - Contamination with microorganisms; process control verification criteria and testing; pathogen...

Code of Federal Regulations, 2011 CFR

2011-01-01

... CERTIFICATION POST-MORTEM INSPECTION § 310.25 Contamination with microorganisms; process control verification... testing. (1) Each official establishment that slaughters livestock must test for Escherichia coli Biotype... poultry, shall test the type of livestock or poultry slaughtered in the greatest number. The establishment...

Modeling Student Software Testing Processes: Attitudes, Behaviors, Interventions, and Their Effects

ERIC Educational Resources Information Center

Buffardi, Kevin John

2014-01-01

Effective software testing identifies potential bugs and helps correct them, producing more reliable and maintainable software. As software development processes have evolved, incremental testing techniques have grown in popularity, particularly with introduction of test-driven development (TDD). However, many programmers struggle to adopt TDD's…

An Item Gains and Losses Analysis of False Memories Suggests Critical Items Receive More Item-Specific Processing than List Items

ERIC Educational Resources Information Center

Burns, Daniel J.; Martens, Nicholas J.; Bertoni, Alicia A.; Sweeney, Emily J.; Lividini, Michelle D.

2006-01-01

In a repeated testing paradigm, list items receiving item-specific processing are more likely to be recovered across successive tests (item gains), whereas items receiving relational processing are likely to be forgotten progressively less on successive tests. Moreover, analysis of cumulative-recall curves has shown that item-specific processing…

Developing a Science Process Skills Test for Secondary Students: Validity and Reliability Study

ERIC Educational Resources Information Center

Feyzioglu, Burak; Demirdag, Baris; Akyildiz, Murat; Altun, Eralp

2012-01-01

Science process skills are claimed to enable an individual to improve their own life visions and give a scientific view/literacy as a standard of their understanding about the nature of science. The main purpose of this study was to develop a test for measuring a valid, reliable and practical test for Science Process Skills (SPS) in secondary…

A macro-ergonomic work system analysis of the diagnostic testing process in an outpatient health care facility for process improvement and patient safety.

PubMed

Hallock, M L; Alper, S J; Karsh, B

The diagnosis of illness is important for quality patient care and patient safety and is greatly aided by diagnostic testing. For diagnostic tests, such as pathology and radiology, to positively impact patient care, the tests must be processed and the physician and patient must be notified of the results in a timely fashion. There are many steps in the diagnostic testing process, from ordering to result dissemination, where the process can break down and therefore delay patient care and reduce patient safety. This study was carried out to examine the diagnostic testing process (i.e. from ordering to result notification) and used a macro-ergonomic work system analysis to uncover system design flaws that contributed to delayed physician and patient notification of results. The study was carried out in a large urban outpatient health-care facility made up of 30 outpatient clinics. Results indicated a number of variances that contributed to delays, the majority of which occurred across the boundaries of different systems and were related to poor or absent feedback structures. Recommendations for improvements are discussed.

Preliminary Characterization Results from the DebriSat Project

NASA Technical Reports Server (NTRS)

Rivero, M.; Shiotani, B.; Kleespies, J.; Toledo-Burdett, R.; Moraguez, M.; Carrasquila, M.; Fitz-Coy, N.; Liou, J.-C.; Sorge, M.; Huynh, T.

2016-01-01

The DebriSat project is a continuing effort sponsored by NASA and DoD to update existing break-up models using data obtained from two separate hypervelocity impact tests used to simulate on-orbit collisions. To protect the fragments resulting from the impact tests, "soft-catch" arenas made of polyurethane foam panels were utilized. After each impact test, the test chamber was cleaned and debris resulting from the catastrophic demise of the test article were collected and shipped to the University of Florida for post-impact processing. The post-impact processing activities include collecting, characterizing, and cataloging of the fragments. Since the impact tests, a team of students has been working to characterize the fragments in terms of their mass, size, shape, color and material content. The focus of the 20 months since the impact tests has been on the collection of 2 millimeters- and larger fragments resulting from impact test on the 56 kilogram-representative LEO (Low Earth Orbit) satellite referred to as DebriSat. To date we have recovered in excess of 115,000 fragments, 30,000 more than the prediction of 85,000 fragments from the existing model. We continue to collect fragments but have transitioned to the characterization phase of the post-impact activities. Since the start of the characterization phase, the focus has been to utilize automation to (i) expedite fragment characterization process and (ii) minimize human-in-the- loop. We have developed and implemented such automated processes; e.g., we have automated the data entry process to reduce operator errors during transcription of the measurement data. However, at all steps of the process, there is human oversight to ensure the integrity of the data. Additionally, we have developed and implemented repeatability and reproducibility tests to ensure that the instrumentation used in the characterization process is accurate and properly calibrated. In this paper, the implemented processes are described and preliminary results presented. Additionally, lessons learned from the implemented automations and their impacts on the integrity of the results are discussed.

Infrared Database for Process Support Materials

NASA Technical Reports Server (NTRS)

Bennett, K. E.; Boothe, R. E.; Burns, H. D.

2003-01-01

Process support materials' compatibility with cleaning processes is critical to ensure final hardware cleanliness and that performance requirements are met. Previous discovery of potential contaminants in process materials shows the need for incoming materials testing and establishment of a process materials database. The Contamination Control Team of the Materials, Processes, and Manufacturing (MP&M) Department at Marshall Space Flight Center (MSFC) has initiated the development of such an infrared (IR) database, called the MSFC Process Materials IR database, of the common process support materials used at MSFC. These process support materials include solvents, wiper cloths, gloves, bagging materials, etc. Testing includes evaluation of the potential of gloves, wiper cloths, and other items to transfer contamination to handled articles in the absence of solvent exposure, and the potential for solvent exposure to induce material degradation. This Technical Memorandum (TM) summarizes the initial testing completed through December 2002. It is anticipated that additional testing will be conducted with updates provided in future TMs.Materials were analyzed using two different IR techniques: (1) Dry transference and (2) liquid extraction testing. The first of these techniques utilized the Nicolet Magna 750 IR spectrometer outfitted with a horizontal attenuated total reflectance (HATR) crystal accessory. The region from 650 to 4,000 wave numbers was analyzed, and 50 scans were performed per IR spectrum. A dry transference test was conducted by applying each sample with hand pressure to the HATR crystal to first obtain a spectrum of the parent material. The material was then removed from the HATR crystal and analyzed to determine the presence of any residues. If volatile, liquid samples were examined both prior to and following evaporation.The second technique was to perform an extraction test with each sample in five different solvents.Once the scans were complete for both the dry transference and the extraction tests, the residue from each scan was interpreted.

Strategy for 90% autoverification of clinical chemistry and immunoassay test results using six sigma process improvement.

PubMed

Randell, Edward W; Short, Garry; Lee, Natasha; Beresford, Allison; Spencer, Margaret; Kennell, Marina; Moores, Zoë; Parry, David

2018-06-01

Six Sigma involves a structured process improvement strategy that places processes on a pathway to continued improvement. The data presented here summarizes a project that took three clinical laboratories from autoverification processes that allowed between about 40% to 60% of tests being auto-verified to more than 90% of tests and samples auto-verified. The project schedule, metrics and targets, a description of the previous system and detailed information on the changes made to achieve greater than 90% auto-verification is presented for this Six Sigma DMAIC (Design, Measure, Analyze, Improve, Control) process improvement project.

7 CFR 28.958 - Payment of fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., TESTING, AND STANDARDS Cotton Fiber and Processing Tests Fiber and Processing Tests § 28.958 Payment of... earlier date. Payment shall be by check or by draft or post office or express money order, payable to the...

7 CFR 28.958 - Payment of fees.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., TESTING, AND STANDARDS Cotton Fiber and Processing Tests Fiber and Processing Tests § 28.958 Payment of... earlier date. Payment shall be by check or by draft or post office or express money order, payable to the...

PLAN-TA9-2443(U), Rev. B Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne

2016-03-16

This document identifies scope and some general procedural steps for performing Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing. This Test Plan describes the requirements, responsibilities, and process for preparing and testing a range of chemical surrogates intended to mimic the energetic response of waste created during processing of legacy nitrate salts. The surrogates developed are expected to bound1 the thermal and mechanical sensitivity of such waste, allowing for the development of process parameters required to minimize the risk to worker and public when processing this waste. Such parameters will be based on the worst-case kinetic parameters as derived frommore » APTAC measurements as well as the development of controls to mitigate sensitivities that may exist due to friction, impact, and spark. This Test Plan will define the scope and technical approach for activities that implement Quality Assurance requirements relevant to formulation and testing.« less

Test processing system (SEE)

NASA Technical Reports Server (NTRS)

Gaulene, P.

1986-01-01

The SEE data processing system, developed in 1985, manages and process test results. General information is provided on the SEE system: objectives, characteristics, basic principles, general organization, and operation. Full documentation is accessible by computer using the HELP SEE command.

A New Comparison Between Conventional Indexing (MEDLARS) and Automatic Text Processing (SMART)

ERIC Educational Resources Information Center

Salton, G.

1972-01-01

A new testing process is described. The design of the test procedure is covered in detail, and the several language processing features incorporated into the SMART system are individually evaluated. (20 references) (Author)

Processing, Properties and Arc Jet Testing of HfB2/SiC

NASA Technical Reports Server (NTRS)

Johnson, Sylvia M.; Beckman, Sarah; Irby, Edward; Ellerby, Don; Gasch, Matt; Gusman, Michael

2004-01-01

Contents include the following: Background on Ultra High Temperature Ceramics - UHTCs. Summary UNTC processing: power processing, scale-up. Preliminary material properties: mechanical, thermal. Arc jet testing: flat face models, cone models. Summary.

The Relationship between Processing and Storage in Working Memory Span: Not Two Sides of the Same Coin

ERIC Educational Resources Information Center

Maehara, Yukio; Saito, Satoru

2007-01-01

In working memory (WM) span tests, participants maintain memory items while performing processing tasks. In this study, we examined the impact of task processing requirements on memory-storage activities, looking at the stimulus order effect and the impact of storage requirements on processing activities, testing the processing time effect in WM…

The effects of mild and severe traumatic brain injury on speed of information processing as measured by the computerized tests of information processing (CTIP).

PubMed

Tombaugh, Tom N; Rees, Laura; Stormer, Peter; Harrison, Allyson G; Smith, Andra

2007-01-01

In spite of the fact that reaction time (RT) measures are sensitive to the effects of traumatic brain injury (TBI), few RT procedures have been developed for use in standard clinical evaluations. The computerized test of information processing (CTIP) [Tombaugh, T. N., & Rees, L. (2000). Manual for the computerized tests of information processing (CTIP). Ottawa, Ont.: Carleton University] was designed to measure the degree to which TBI decreases the speed at which information is processed. The CTIP consists of three computerized programs that progressively increase the amount of information that is processed. Results of the current study demonstrated that RT increased as the difficulty of the CTIP tests increased (known as the complexity effect), and as severity of injury increased (from mild to severe TBI). The current study also demonstrated the importance of selecting a non-biased measure of variability. Overall, findings suggest that the CTIP is an easy to administer and sensitive measure of information processing speed.

Set of Criteria for Efficiency of the Process Forming the Answers to Multiple-Choice Test Items

ERIC Educational Resources Information Center

Rybanov, Alexander Aleksandrovich

2013-01-01

Is offered the set of criteria for assessing efficiency of the process forming the answers to multiple-choice test items. To increase accuracy of computer-assisted testing results, it is suggested to assess dynamics of the process of forming the final answer using the following factors: loss of time factor and correct choice factor. The model…

The Impact of Retrieval Processes, Age, General Achievement Level, and Test Scoring Scheme for Children's Metacognitive Monitoring and Controlling

ERIC Educational Resources Information Center

Krebs, Saskia Susanne; Roebers, Claudia Maria

2012-01-01

This multi-phase study examined the influence of retrieval processes on children's metacognitive processes in relation to and in interaction with achievement level and age. First, N = 150 9/10- and 11/12-year old high and low achievers watched an educational film and predicted their test performance. Children then solved a cloze test regarding the…

Number of solutions effects in stem decision: support for the distinction between identification and production processes in priming.

PubMed

Barnhardt, Terrence M

2005-10-01

Three experiments explored the distinction between identification and production processes (e.g., Gabrieli et al., 1999). A stem decision test was introduced, in which participants were asked to state whether there were any English words that began with the presented three-letter stems. In Experiment 1, stem decision priming was robust for single-solution stems, but much reduced for many-solution stems. In Experiment 2, the solutions effect in stem decision was replicated in a within-subjects design, as was the contrast between the presence of priming in a many-solution stem completion test and the absence of priming in a many-solution stem decision test. In Experiment 3, for each critical many-solution stem in the stem decision test, participants studied three words that began with those three letters. Again, priming was not observed. These results were consistent with the notions that (a) many-solution stem completion relies on production processes, (b) the stem decision test eliminates production processes, and (c) single-solution priming relies on identification processes, regardless of whether the test is stem completion or stem decision.

Central Control Room in the Engine Research Building

NASA Image and Video Library

1968-11-21

Operators in the Engine Research Building’s Central Control Room at the National Aeronautics and Space Administration (NASA) Lewis Research Center. The massive 4.25-acre Engine Research Building contains dozens of test cells, test stands, and altitude chambers. A powerful a collection of compressors and exhausters located in the central portion of the basement provides process air and exhaust for these test areas. This system is connected to similar process air systems in the laboratory’s other large test facilities. The Central Control Room coordinates this activity and communicates with the local utilities. The panels on the wall contain schematics with indicator lights and instrumentation for the atmospheric exhaust, altitude exhaust, refrigerated air, and process air systems. The process air equipment included twelve exhausters, four compressors, refrigeration system, cooling water, and an exhaust system. The operators in the control room kept in contact with engineers running the process air system and those conducting the tests in the test cells. The operators also coordinated with the local power companies to make sure enough electricity was available to operate the powerful compressors and exhausters.

Cytochrome P450 (CYP450) Tests

MedlinePlus

... P450 (CYP450) tests Overview Your doctor may use cytochrome P450 (CYP450) tests to help determine how your body processes (metabolizes) a drug. The human body contains P450 enzymes to process medications. Because of inherited (genetic) traits ...

Waiting is the hardest part: anticipating medical test results affects processing and recall of important information.

PubMed

Portnoy, David B

2010-07-01

Waiting for medical test results that signal physical harm can be a stressful and potentially psychologically harmful experience. Despite this, interventionists and physicians often use this wait time to deliver behavior change messages and other important information about the test, possible results and its implications. This study examined how "bracing" for a medical test result impacts cognitive processing, as well as recall of information delivered during this period. Healthy U.S. university students (N = 150) were tested for a deficiency of a fictitious saliva biomarker that was said to be predictive of long-term health problems using a 2 (Test Result) x 2 (Expected immediacy of result: 10 min, 1 month) factorial design. Participants expecting to get the test result shortly should have been bracing for the result. While waiting for the test results participants completed measures of cognitive processing. After participants received the test result, recall of information about the biomarker was tested in addition to cognitive measures. One week later, participants who were originally told they did not have the deficiency had their recall assessed again. Results showed that anticipating an imminent test result increased cognitive distraction in the processing of information and lowered recall of information about the test and the biomarker. These results suggest that delivering critical information to patients after administering a test and immediately before giving the results may not be optimal.

Plasma Processing of Model Residential Solid Waste

NASA Astrophysics Data System (ADS)

Messerle, V. E.; Mossé, A. L.; Nikonchuk, A. N.; Ustimenko, A. B.; Baimuldin, R. V.

2017-09-01

The authors have tested the technology of processing of model residential solid waste. They have developed and created a pilot plasma unit based on a plasma chamber incinerator. The waste processing technology has been tested and prepared for commercialization.

A Comparison of Visual and Auditory Processing Tests on the Woodcock-Johnson Tests of Cognitive Ability, Revised and the Learning Efficiency Test-II.

ERIC Educational Resources Information Center

Bolen, L. M.; Kimball, D. J.; Hall, C. W.; Webster, R. E.

1997-01-01

Compares the visual and auditory processing factors of the Woodcock Johnson Tests of Cognitive Ability, Revised (WJR COG) and the visual and auditory memory factors of the Learning Efficiency Test, II (LET-II) among 120 college students. Results indicate two significant performance differences between the WJR COG and LET-II. (RJM)

Effects of Test Media on Different EFL Test-Takers in Writing Scores and in the Cognitive Writing Process

ERIC Educational Resources Information Center

Zou, Xiao-Ling; Chen, Yan-Min

2016-01-01

The effects of computer and paper test media on EFL test-takers with different computer familiarity in writing scores and in the cognitive writing process have been comprehensively explored from the learners' aspect as well as on the basis of related theories and practice. The results indicate significant differences in test scores among the…

The longevity of adaptive memory: evidence for mnemonic advantages of survival processing 24 and 48 hours later.

PubMed

Raymaekers, Linsey H C; Otgaar, Henry; Smeets, Tom

2014-01-01

Prior studies have convincingly demonstrated that survival-related processing of information enhances its subsequent retention. This phenomenon, known as the survival recall advantage, generalises to other stimuli, memory domains, and research populations, thereby underscoring its reliability. As previous studies used only short retention intervals between survival processing and the memory test, an important yet hitherto unanswered issue is whether this effect persists over time. The present experiment therefore examined whether survival processing also produces mnemonic benefits when retention is tested after longer delay periods. Participants (N =81) rated the relevance of words according to a survival and a moving scenario, and were then randomly assigned to the typical immediate (3-minute delay) retention test condition or conditions that included a 24- or 48-hour interval between survival processing and memory testing. In each of these conditions survival processing led to higher surprise free recall and recognition rates than processing words according to the moving scenario. Thus this study provides evidence that illustrates the longevity of survival processing advantages on memory performance.

“The Relationship between Executive Functioning, Processing Speed and White Matter Integrity in Multiple Sclerosis”

PubMed Central

Genova, Helen M.; DeLuca, John; Chiaravalloti, Nancy; Wylie, Glenn

2014-01-01

The primary purpose of the current study was to examine the relationship between performance on executive tasks and white matter integrity, assessed by diffusion tensor imaging (DTI) in Multiple Sclerosis (MS). A second aim was to examine how processing speed affects the relationship between executive functioning and FA. This relationship was examined in two executive tasks that rely heavily on processing speed: the Color-Word Interference Test and Trail-Making Test (Delis-Kaplan Executive Function System). It was hypothesized that reduced fractional anisotropy (FA) is related to poor performance on executive tasks in MS, but that this relationship would be affected by the statistical correction of processing speed from the executive tasks. 15 healthy controls and 25 persons with MS participated. Regression analyses were used to examine the relationship between executive functioning and FA, both before and after processing speed was removed from the executive scores. Before processing speed was removed from the executive scores, reduced FA was associated with poor performance on Color-Word Interference Test and Trail-Making Test in a diffuse network including corpus callosum and superior longitudinal fasciculus. However, once processing speed was removed, the relationship between executive functions and FA was no longer significant on the Trail Making test, and significantly reduced and more localized on the Color-Word Interference Test. PMID:23777468

What's to Be Done About Laboratory Quality? Process Indicators, Laboratory Stewardship, the Outcomes Problem, Risk Assessment, and Economic Value: Responding to Contemporary Global Challenges.

PubMed

Meier, Frederick A; Badrick, Tony C; Sikaris, Kenneth A

2018-02-17

For 50 years, structure, process, and outcomes measures have assessed health care quality. For clinical laboratories, structural quality has generally been assessed by inspection. For assessing process, quality indicators (QIs), statistical monitors of steps in the clinical laboratory total testing, have proliferated across the globe. Connections between structural and process laboratory measures and patient outcomes, however, have rarely been demonstrated. To inform further development of clinical laboratory quality systems, we conducted a selective but worldwide review of publications on clinical laboratory quality assessment. Some QIs, like seven generic College of American Pathologists Q-Tracks monitors, have demonstrated significant process improvement; other measures have uncovered critical opportunities to improve test selection and result management. The College of Pathologists of Australasia Key Indicator Monitoring and Management System has deployed risk calculations, introduced from failure mode effects analysis, as surrogate measures for outcomes. Showing economic value from clinical laboratory testing quality is a challenge. Clinical laboratories should converge on fewer (7-14) rather than more (21-35) process monitors; monitors should cover all steps of the testing process under laboratory control and include especially high-risk specimen-quality QIs. Clinical laboratory stewardship, the combination of education interventions among clinician test orderers and report consumers with revision of test order formats and result reporting schemes, improves test ordering, but improving result reception is more difficult. Risk calculation reorders the importance of quality monitors by balancing three probabilities: defect frequency, weight of potential harm, and detection difficulty. The triple approach of (1) a more focused suite of generic consensus quality indicators, (2) more active clinical laboratory testing stewardship, and (3) integration of formal risk assessment, rather than competing with economic value, enhances it.

Design Of Computer Based Test Using The Unified Modeling Language

NASA Astrophysics Data System (ADS)

Tedyyana, Agus; Danuri; Lidyawati

2017-12-01

The Admission selection of Politeknik Negeri Bengkalis through interest and talent search (PMDK), Joint Selection of admission test for state Polytechnics (SB-UMPN) and Independent (UM-Polbeng) were conducted by using paper-based Test (PBT). Paper Based Test model has some weaknesses. They are wasting too much paper, the leaking of the questios to the public, and data manipulation of the test result. This reasearch was Aimed to create a Computer-based Test (CBT) models by using Unified Modeling Language (UML) the which consists of Use Case diagrams, Activity diagram and sequence diagrams. During the designing process of the application, it is important to pay attention on the process of giving the password for the test questions before they were shown through encryption and description process. RSA cryptography algorithm was used in this process. Then, the questions shown in the questions banks were randomized by using the Fisher-Yates Shuffle method. The network architecture used in Computer Based test application was a client-server network models and Local Area Network (LAN). The result of the design was the Computer Based Test application for admission to the selection of Politeknik Negeri Bengkalis.

21 CFR 211.194 - Laboratory records.

Code of Federal Regulations, 2010 CFR

2010-04-01

... specific component, drug product container, closure, in-process material, or drug product, and lot tested... product container, closure, in-process material, or drug product tested. (7) The initials or signature of... of any testing and standardization of laboratory reference standards, reagents, and standard...

A Plea for Process in Personality Prevarication

PubMed Central

Kuncel, Nathan R.; Goldberg, Lewis R.; Kiger, Tom

2011-01-01

We make a series recommendations for focusing research on personality test faking. Overall we suggest that a focus on the response process test takers go through will accelerate our understanding of faking behavior. We argue that the decision making process for faking must be simple and dependent on a modest set of decision rules or heuristics. The set of heuristics used by any given test taker will, in turn, be the result of test taker goals and situational press. By focusing in on what the test taker is doing we will avoid adopting the wrong frame of reference and, hopefully, make ever more rapid progress. PMID:21966260

Holistic processing, contact, and the other-race effect in face recognition.

PubMed

Zhao, Mintao; Hayward, William G; Bülthoff, Isabelle

2014-12-01

Face recognition, holistic processing, and processing of configural and featural facial information are known to be influenced by face race, with better performance for own- than other-race faces. However, whether these various other-race effects (OREs) arise from the same underlying mechanisms or from different processes remains unclear. The present study addressed this question by measuring the OREs in a set of face recognition tasks, and testing whether these OREs are correlated with each other. Participants performed different tasks probing (1) face recognition, (2) holistic processing, (3) processing of configural information, and (4) processing of featural information for both own- and other-race faces. Their contact with other-race people was also assessed with a questionnaire. The results show significant OREs in tasks testing face memory and processing of configural information, but not in tasks testing either holistic processing or processing of featural information. Importantly, there was no cross-task correlation between any of the measured OREs. Moreover, the level of other-race contact predicted only the OREs obtained in tasks testing face memory and processing of configural information. These results indicate that these various cross-race differences originate from different aspects of face processing, in contrary to the view that the ORE in face recognition is due to cross-race differences in terms of holistic processing. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Model-based software process improvement

NASA Technical Reports Server (NTRS)

Zettervall, Brenda T.

1994-01-01

The activities of a field test site for the Software Engineering Institute's software process definition project are discussed. Products tested included the improvement model itself, descriptive modeling techniques, the CMM level 2 framework document, and the use of process definition guidelines and templates. The software process improvement model represents a five stage cyclic approach for organizational process improvement. The cycles consist of the initiating, diagnosing, establishing, acting, and leveraging phases.

Telerobotic electronic materials processing experiment

NASA Technical Reports Server (NTRS)

Ollendorf, Stanford

1991-01-01

The Office of Commercial Programs (OCP), working in conjunction with NASA engineers at the Goddard Space Flight Center, is supporting research efforts in robot technology and microelectronics materials processing that will provide many spinoffs for science and industry. The Telerobotic Materials Processing Experiment (TRMPX) is a Shuttle-launched materials processing test payload using a Get Away Special can. The objectives of the project are to define, develop, and demonstrate an automated materials processing capability under realistic flight conditions. TRMPX will provide the capability to test the production processes that are dependent on microgravity. The processes proposed for testing include the annealing of amorphous silicon to increase grain size for more efficient solar cells, thin film deposition to demonstrate the potential of fabricating solar cells in orbit, and the annealing of radiation damaged solar cells.

ASRM test report: Autoclave cure process development

NASA Technical Reports Server (NTRS)

Nachbar, D. L.; Mitchell, Suzanne

1992-01-01

ASRM insulated segments will be autoclave cured following insulation pre-form installation and strip wind operations. Following competitive bidding, Aerojet ASRM Division (AAD) Purchase Order 100142 was awarded to American Fuel Cell and Coated Fabrics Company, Inc. (Amfuel), Magnolia, AR, for subcontracted insulation autoclave cure process development. Autoclave cure process development test requirements were included in Task 3 of TM05514, Manufacturing Process Development Specification for Integrated Insulation Characterization and Stripwind Process Development. The test objective was to establish autoclave cure process parameters for ASRM insulated segments. Six tasks were completed to: (1) evaluate cure parameters that control acceptable vulcanization of ASRM Kevlar-filled EPDM insulation material; (2) identify first and second order impact parameters on the autoclave cure process; and (3) evaluate insulation material flow-out characteristics to support pre-form configuration design.

Neurophysiological evidence for transfer appropriate processing of memory: processing versus feature similarity.

PubMed

Schendan, Haune E; Kutas, Malra

2007-08-01

Transfer appropriate processing (TAP) accounts propose that memory is a function of the degree to which the same neural processes transfer appropriately from the study experience to the memory test. However, in prior research, study and test stimuli were often similar physically. In two experiments, event-related brain potentials (ERPs) were recorded to fragmented objects during an indirect memory test to isolate transfer of a specific perceptual process from overlap of physical features between experiences. An occipitotemporoparietal P2(00) at 200 msec showed implicit memory effects only when similar perceptual grouping processes of good continuation were repeatedly engaged-despite physical feature differences--as TAP accounts hypothesize. This result provides direct neurophysiological evidence for the critical role of process transfer across experiences for memory.

DATA SUMMARY REPORT SMALL SCALE MELTER TESTING OF HLW ALGORITHM GLASSES MATRIX1 TESTS VSL-07S1220-1 REV 0 7/25/07

DOE Office of Scientific and Technical Information (OSTI.GOV)

KRUGER AA; MATLACK KS; PEGG IL

2011-12-29

Eight tests using different HLW feeds were conducted on the DM100-BL to determine the effect of variations in glass properties and feed composition on processing rates and melter conditions (off-gas characteristics, glass processing, foaming, cold cap, etc.) at constant bubbling rate. In over seven hundred hours of testing, the property extremes of glass viscosity, electrical conductivity, and T{sub 1%}, as well as minimum and maximum concentrations of several major and minor glass components were evaluated using glass compositions that have been tested previously at the crucible scale. Other parameters evaluated with respect to glass processing properties were +/-15% batching errorsmore » in the addition of glass forming chemicals (GFCs) to the feed, and variation in the sources of boron and sodium used in the GFCs. Tests evaluating batching errors and GFC source employed variations on the HLW98-86 formulation (a glass composition formulated for HLW C-106/AY-102 waste and processed in several previous melter tests) in order to best isolate the effect of each test variable. These tests are outlined in a Test Plan that was prepared in response to the Test Specification for this work. The present report provides summary level data for all of the tests in the first test matrix (Matrix 1) in the Test Plan. Summary results from the remaining tests, investigating minimum and maximum concentrations of major and minor glass components employing variations on the HLW98-86 formulation and glasses generated by the HLW glass formulation algorithm, will be reported separately after those tests are completed. The test data summarized herein include glass production rates, the type and amount of feed used, a variety of measured melter parameters including temperatures and electrode power, feed sample analysis, measured glass properties, and gaseous emissions rates. More detailed information and analysis from the melter tests with complete emission chemistry, glass durability, and melter operating details will be provided in the final report. A summary of the tests that were conducted is provided in Table 1. Each of the seven tests was of nominally one hundred hours in duration. Test B was conducted in two equal segments: the first with nominal additives, and the second with the replacement of borax with a mixture of boric acid and soda ash to determine the effect of alternative OPC sources on production rates and processing characteristics. Interestingly, sugar additions were required near mid points of Tests W and Z to reduce excessive foaming that severely limited feed processing rates. The sugar additions were very effective in recovering manageable processing conditions, albeit over the relatively short remainder of the test duration. Tests W and Z employed the highest melt viscosities but not by a particularly wide margin. Other tests, which did not exhibit such foaming Issues, employed higher concentrations of manganese or iron or both. These results highlight the need for the development of protocols for the a priori determination of which HLW feeds will require sugar additions and the appropriate amounts of sugar to be added in order to control foaming (and maintain throughput) without over-reduction of the melt (which could lead to molten metal formation). In total, over 8,800 kg of feed was processed to produce over 3200 kg of glass. Steady-state processing rates were achieved, and no secondary sulfate phases were observed during any of the tests. Analysis was performed on samples of the glass product taken throughout the tests to verify composition and properties. Sampling and analysis was also performed on melter exhaust to determine the effect of the feed and glass changes on melter emissions.« less

The use of test structures for reliability prediction and process control of integrated circuits and photovoltaics

NASA Astrophysics Data System (ADS)

Trachtenberg, I.

How a reliability model might be developed with new data from accelerated stress testing, failure mechanisms, process control monitoring, and test structure evaluations is illustrated. The effects of the acceleration of temperature on operating life is discussed. Test structures that will further accelerate the failure rate are discussed. Corrosion testing is addressed. The uncoated structure is encapsulated in a variety of mold compounds and subjected to pressure-cooker testing.

Process Definition and Modeling Guidebook. Version 01.00.02

DTIC Science & Technology

1992-12-01

material (and throughout the guidebook)process defnition is considered to be the act of representing the important characteristics of a process in a...characterized by software standards and guidelines, software inspections and reviews, and more formalized testing (including test plans, test sup- port tools...paper-based approach works well for training, examples, and possibly even small pilot projects and case studies. However, large projects will benefit from

"Chance favors only the prepared mind": preparing minds to systematically reduce hazards in the testing process in primary care.

PubMed

Singh, Ranjit; Hickner, John; Mold, Jim; Singh, Gurdev

2014-03-01

Testing plays a vital role in primary care. Failures in the process are common and can be harmful. As the great 19th century microbiologist Louis Pasteur put it "chance favors only the prepared mind." Our objective is to prepare minds in primary care practices to improve safety in the testing process. Various principles from safety science can be applied. A prospective methodology that uses an anonymous practice survey based on concepts from failure modes and effects analysis is proposed. Responses are used to rank perceived hazards in the testing process, leading to prioritization of areas for intervention. Secondary data analysis (using data from a study of medication safety) was used to explore the value of this approach in the context of assessing the testing process. At 3 primary care practice sites, a total of 61 staff members completed 4 survey items examining the testing process. Comparison across practices shows that each has a distinct profile of hazards, which would lead each on a different path toward improvement. The proposed approach treats each practice as a unique complex adaptive system aiming to help it thrive by inculcating trust, mutual respect, and collaboration. Implications for patient safety research and practice are discussed.

Achievement Test Preparation: A Year-Long Goal, Not a Last-Minute Thought.

ERIC Educational Resources Information Center

Matter, M. Kevin; Ligon, Glynn

Yearly administrations of a standardized achievement test are a part of the educational process in many school districts in the United States. The Systemwide Testing Program in the Austin Independent School District Office of Research and Evaluation has gradually developed a process and support materials whereby the test administrations are a tool…

Testing Methodology in the Student Learning Process

ERIC Educational Resources Information Center

Gorbunova, Tatiana N.

2017-01-01

The subject of the research is to build methodologies to evaluate the student knowledge by testing. The author points to the importance of feedback about the mastering level in the learning process. Testing is considered as a tool. The object of the study is to create the test system models for defence practice problems. Special attention is paid…

Survey of Adult Students with Mathematical Difficulties

ERIC Educational Resources Information Center

Jarlskog, Linda

2016-01-01

This paper relates to one of the test procedures being used in Sweden, used to establish if students need a more thorough investigation of their mathematical difficulties. This paper mainly describes the test process and the results from 10 test subjects. The paper also refers to parts of the research forming the basis for the test process. The…

Triggers of self-conscious emotions in the sexually transmitted infection testing process

PubMed Central

2010-01-01

Background Self-conscious emotions (shame, guilt and embarrassment) are part of many individuals' experiences of seeking STI testing. These emotions can have negative impacts on individuals' interpretations of the STI testing process, their willingness to seek treatment and their willingness to inform sexual partners in light of positive STI diagnoses. Because of these impacts, researchers have called for more work to be completed on the connections between shame, guilt, embarrassment and STI testing. We examine the specific events in the STI testing process that trigger self-conscious emotions in young adults who seek STI testing; and to understand what it is about these events that triggers these emotions. Semi-structured interviews with 30 adults (21 women, 9 men) in the Republic of Ireland. Findings Seven specific triggers of self-conscious emotions were identified. These were: having unprotected sex, associated with the initial reason for seeking STI testing; talking to partners and peers about the intention to seek STI testing; the experience of accessing STI testing facilities and sitting in clinic waiting rooms; negative interactions with healthcare professionals; receiving a positive diagnosis of an STI; having to notify sexual partners in light of a positive STI diagnosis; and accessing healthcare settings for treatment for an STI. Self-conscious emotions were triggered in each case by a perceived threat to respondents' social identities. Conclusion There are multiple triggers of self-conscious emotions in the STI testing process, ranging from the initial decision to seek testing, right through to the experience of accessing treatment. The role of self-conscious emotions needs to be considered in each component of service design from health promotion approaches, through facility layout to the training of all professionals involved in the STI testing process. PMID:20716339

Technical activities report: Heat, water, and mechanical studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander, W.K.

1951-10-04

Topics in the heat studies section include: front and rear face reflector shields at the C-pile; process tube channel thermocouples; water temperature limits for horizontal rods; slug temperature and thermal conductivity calculations; maximum slug-end cap temperature; boiling consideration studies; scram time limit for Panellit alarm; heat transfer test; slug stresses; thermal insulation of bottom tube row at C-pile; flow tests; present pile enrichment; electric analog; and measurement of thermal contact resistance. Topics in the water studies section include: 100-D flow laboratory; process water studies; fundamental studies on film formation; coatings on tip-offs; can difference tests; slug jacket abrasion at highmore » flow rates; corrosion studies; front tube dummy slugs; metallographic examination of tubes from H-pile; fifty-tube mock-up; induction heating facility; operational procedures and standards; vertical safety rod dropping time tests; recirculation; and power recovery. Mechanical development studies include: effect of Sphincter seal and lubricant VSR drop time; slug damage; slug bubble tester; P-13 removal; chemical slug stripper; effect of process tube rib spacing and width; ink facility installation; charging and discharging machines; process tube creep; flapper nozzle assembly test; test of single gun barrel assembly; pigtail fixture test; horizontal rod gland seal test; function test of C-pile; and intermediate test of Ball 3-X and VSR systems.« less

20 CFR 404.906 - Testing modifications to the disability determination procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-AGE, SURVIVORS AND DISABILITY INSURANCE (1950- ) Determinations, Administrative Review Process, and... set out in this section to test modifications to our disability determination process. These... appropriate; and eliminating the reconsideration step in the administrative review process and having a...

Parameters of Emotional Processing in Neuropsychiatric Disorders: Conceptual Issues and a Battery of Tests.

ERIC Educational Resources Information Center

Borod, Joan C.; And Others

1990-01-01

Components of emotional processing (communication channel, processing mode, and emotional valence) were examined in psychiatric and neurological populations, using an experimental affect battery. The test battery exhibited good psychometric properties and discriminated among diagnostic groups. (Author/JDD)

Taking advantage of ground data systems attributes to achieve quality results in testing software

NASA Technical Reports Server (NTRS)

Sigman, Clayton B.; Koslosky, John T.; Hageman, Barbara H.

1994-01-01

During the software development life cycle process, basic testing starts with the development team. At the end of the development process, an acceptance test is performed for the user to ensure that the deliverable is acceptable. Ideally, the delivery is an operational product with zero defects. However, the goal of zero defects is normally not achieved but is successful to various degrees. With the emphasis on building low cost ground support systems while maintaining a quality product, a key element in the test process is simulator capability. This paper reviews the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) test tool that is used in the acceptance test process for unmanned satellite operations control centers. The TASS is designed to support the development, test and operational environments of the Goddard Space Flight Center (GSFC) operations control centers. The TASS uses the same basic architecture as the operations control center. This architecture is characterized by its use of distributed processing, industry standards, commercial off-the-shelf (COTS) hardware and software components, and reusable software. The TASS uses much of the same TPOCC architecture and reusable software that the operations control center developer uses. The TASS also makes use of reusable simulator software in the mission specific versions of the TASS. Very little new software needs to be developed, mainly mission specific telemetry communication and command processing software. By taking advantage of the ground data system attributes, successful software reuse for operational systems provides the opportunity to extend the reuse concept into the test area. Consistency in test approach is a major step in achieving quality results.

Auditory Alterations in Children Infected by Human Immunodeficiency Virus Verified Through Auditory Processing Test

PubMed Central

Romero, Ana Carla Leite; Alfaya, Lívia Marangoni; Gonçales, Alina Sanches; Frizzo, Ana Claudia Figueiredo; Isaac, Myriam de Lima

2016-01-01

Introduction The auditory system of HIV-positive children may have deficits at various levels, such as the high incidence of problems in the middle ear that can cause hearing loss. Objective The objective of this study is to characterize the development of children infected by the Human Immunodeficiency Virus (HIV) in the Simplified Auditory Processing Test (SAPT) and the Staggered Spondaic Word Test. Methods We performed behavioral tests composed of the Simplified Auditory Processing Test and the Portuguese version of the Staggered Spondaic Word Test (SSW). The participants were 15 children infected by HIV, all using antiretroviral medication. Results The children had abnormal auditory processing verified by Simplified Auditory Processing Test and the Portuguese version of SSW. In the Simplified Auditory Processing Test, 60% of the children presented hearing impairment. In the SAPT, the memory test for verbal sounds showed more errors (53.33%); whereas in SSW, 86.67% of the children showed deficiencies indicating deficit in figure-ground, attention, and memory auditory skills. Furthermore, there are more errors in conditions of background noise in both age groups, where most errors were in the left ear in the Group of 8-year-olds, with similar results for the group aged 9 years. Conclusion The high incidence of hearing loss in children with HIV and comorbidity with several biological and environmental factors indicate the need for: 1) familiar and professional awareness of the impact on auditory alteration on the developing and learning of the children with HIV, and 2) access to educational plans and follow-up with multidisciplinary teams as early as possible to minimize the damage caused by auditory deficits. PMID:28050213

Vocabulary Knowledge Predicts Lexical Processing: Evidence from a Group of Participants with Diverse Educational Backgrounds

PubMed Central

Mainz, Nina; Shao, Zeshu; Brysbaert, Marc; Meyer, Antje S.

2017-01-01

Vocabulary knowledge is central to a speaker's command of their language. In previous research, greater vocabulary knowledge has been associated with advantages in language processing. In this study, we examined the relationship between individual differences in vocabulary and language processing performance more closely by (i) using a battery of vocabulary tests instead of just one test, and (ii) testing not only university students (Experiment 1) but young adults from a broader range of educational backgrounds (Experiment 2). Five vocabulary tests were developed, including multiple-choice and open antonym and synonym tests and a definition test, and administered together with two established measures of vocabulary. Language processing performance was measured using a lexical decision task. In Experiment 1, vocabulary and word frequency were found to predict word recognition speed while we did not observe an interaction between the effects. In Experiment 2, word recognition performance was predicted by word frequency and the interaction between word frequency and vocabulary, with high-vocabulary individuals showing smaller frequency effects. While overall the individual vocabulary tests were correlated and showed similar relationships with language processing as compared to a composite measure of all tests, they appeared to share less variance in Experiment 2 than in Experiment 1. Implications of our findings concerning the assessment of vocabulary size in individual differences studies and the investigation of individuals from more varied backgrounds are discussed. PMID:28751871

Criteria for identifying the molecular basis of the engram (CaMKII, PKMzeta).

PubMed

Lisman, John

2017-11-29

The engram refers to the molecular changes by which a memory is stored in the brain. Substantial evidence suggests that memory involves learning-dependent changes at synapses, a process termed long-term potentiation (LTP). Thus, understanding the storages process that underlies LTP may provide insight into how the engram is stored. LTP involves induction, maintenance (storage), and expression sub-processes; special tests are required to specifically reveal properties of the storage process. The strongest of these is the Erasure test in which a transiently applied agent that attacks a putative storage molecule may lead to persistent erasure of previously induced LTP/memory. Two major hypotheses have been proposed for LTP/memory storage: the CaMKII and PKM-zeta hypotheses. After discussing the tests that can be used to identify the engram (Necessity test, Saturation/Occlusion test, Erasure test), the status of these hypotheses is evaluated, based on the literature on LTP and memory-guided behavior. Review of the literature indicates that all three tests noted above support the CaMKII hypothesis when done at both the LTP level and at the behavioral level. Taken together, the results strongly suggest that the engram is stored by an LTP process in which CaMKII is a critical memory storage molecule.

A whole process quality control system for energy measuring instruments inspection based on IOT technology

NASA Astrophysics Data System (ADS)

Yin, Bo; Liu, Li; Wang, Jiahan; Li, Xiran; Liu, Zhenbo; Li, Dewei; Wang, Jun; Liu, Lu; Wu, Jun; Xu, Tingting; Cui, He

2017-10-01

Electric energy measurement as a basic work, an accurate measurements play a vital role for the economic interests of both parties of power supply, the standardized management of the measurement laboratory at all levels is a direct factor that directly affects the fairness of measurement. Currently, the management of metering laboratories generally uses one-dimensional bar code as the recognition object, advances the testing process by manual management, most of the test data requires human input to generate reports. There are many problems and potential risks in this process: Data cannot be saved completely, cannot trace the status of inspection, the inspection process isn't completely controllable and so on. For the provincial metrology center's actual requirements of the whole process management for the performance test of the power measuring appliances, using of large-capacity RF tags as a process management information media, we developed a set of general measurement experiment management system, formulated a standardized full performance test process, improved the raw data recording mode of experimental process, developed a storehouse automatic inventory device, established a strict test sample transfer and storage system, ensured that all the raw data of the inspection can be traced back, achieved full life-cycle control of the sample, significantly improved the quality control level and the effectiveness of inspection work.

16 CFR 1210.16 - Production testing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... in the manufacturing process, the assembly process, the equipment used to manufacture the product, or... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Production testing. 1210.16 Section 1210.16... STANDARD FOR CIGARETTE LIGHTERS Certification Requirements § 1210.16 Production testing. (a) General...

Age-Associated Differences in Cognitive Performance in Older Community Dwelling Schizophrenia Patients: Differential Sensitivity of Clinical Neuropsychological and Experimental Information Processing Tests

PubMed Central

Bowie, Christopher R.; Reichenberg, Abraham; McClure, Margaret M.; Leung, Winnie L.; Harvey, Philip D.

2008-01-01

Cognitive dysfunction is a common feature of schizophrenia and deficits are present before the onset of psychosis, and are moderate to severe by the time of the first episode. Controversy exists over the course of cognitive dysfunction after the first episode. This study examined age-associated differences in performance on clinical neuropsychological (NP) and information processing tasks in a sample of geriatric community living schizophrenia patients (n=172). Compared to healthy control subjects (n=70), people with schizophrenia did not differ on NP tests across age groups but showed evidence for age-associated cognitive worsening on the more complex components of an information-processing test. Age-related changes in cognitive function in schizophrenia may be a function of both the course of illness and the processing demands of the cognitive measure of interest. Tests with fixed difficulty, such as clinical NP tests, may differ in their sensitivity from tests for which parametric difficulty manipulations can be performed. PMID:18053687

Continuous-flow stirred-tank reactor 20-L demonstration test: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, D.D.; Collins, J.L.

One of the proposed methods of removing the cesium, strontium, and transuranics from the radioactive waste storage tanks at Savannah River is the small-tank tetraphenylborate (TPB) precipitation process. A two-reactor-in-series (15-L working volume each) continuous-flow stirred-tank reactor (CSTR) system was designed, constructed, and installed in a hot cell to test the Savannah River process. The system also includes two cross-flow filtration systems to concentrate and wash the slurry produced in the process, which contains the bulk of radioactivity from the supernatant processed through the system. Installation, operational readiness reviews, and system preparation and testing were completed. The first test usingmore » the filtration systems, two CSTRs, and the slurry concentration system was conducted over a 61-h period with design removal of Cs, Sr, and U achieved. With the successful completion of Test 1a, the following tests, 1b and 1c, were not required.« less

Melter Throughput Enhancements for High-Iron HLW

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, A. A.; Gan, Hoa; Joseph, Innocent

2012-12-26

This report describes work performed to develop and test new glass and feed formulations in order to increase glass melting rates in high waste loading glass formulations for HLW with high concentrations of iron. Testing was designed to identify glass and melter feed formulations that optimize waste loading and waste processing rate while meeting all processing and product quality requirements. The work included preparation and characterization of crucible melts to assess melt rate using a vertical gradient furnace system and to develop new formulations with enhanced melt rate. Testing evaluated the effects of waste loading on glass properties and themore » maximum waste loading that can be achieved. The results from crucible-scale testing supported subsequent DuraMelter 100 (DM100) tests designed to examine the effects of enhanced glass and feed formulations on waste processing rate and product quality. The DM100 was selected as the platform for these tests due to its extensive previous use in processing rate determination for various HLW streams and glass compositions.« less

In situ vitrification application to buried waste: Final report of intermediate field tests at Idaho National Engineering Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Callow, R.A.; Weidner, J.R.; Loehr, C.A.

This report describes two in situ vitrification field tests conducted on simulated buried waste pits during June and July 1990 at the Idaho National Engineering Laboratory. In situ vitrification, an emerging technology for in place conversion of contaminated soils into a durable glass and crystalline waste form, is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to access the general suitability of the process to remediate waste structures representative of buried waste found at Idaho National Engineering Laboratory. In particular, these tests, as part of a treatability study, were designedmore » to provide essential information on the field performance of the process under conditions of significant combustible and metal wastes and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology successfully processed the high metal content waste. Test results indicate the process is a feasible technology for application to buried waste. 33 refs., 109 figs., 39 tabs.« less

A Systems Engineering Approach to Quality Assurance for Aerospace Testing

NASA Technical Reports Server (NTRS)

Shepherd, Christena C.

2015-01-01

On the surface, it appears that AS91001 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK)2 that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness.

Face Perception and Test Reliabilities in Congenital Prosopagnosia in Seven Tests

PubMed Central

Esins, Janina; Schultz, Johannes; Stemper, Claudia; Kennerknecht, Ingo

2016-01-01

Congenital prosopagnosia, the innate impairment in recognizing faces, is a very heterogeneous disorder with different phenotypical manifestations. To investigate the nature of prosopagnosia in more detail, we tested 16 prosopagnosics and 21 controls with an extended test battery addressing various aspects of face recognition. Our results show that prosopagnosics exhibited significant impairments in several face recognition tasks: impaired holistic processing (they were tested amongst others with the Cambridge Face Memory Test (CFMT)) as well as reduced processing of configural information of faces. This test battery also revealed some new findings. While controls recognized moving faces better than static faces, prosopagnosics did not exhibit this effect. Furthermore, prosopagnosics had significantly impaired gender recognition—which is shown on a groupwise level for the first time in our study. There was no difference between groups in the automatic extraction of face identity information or in object recognition as tested with the Cambridge Car Memory Test. In addition, a methodological analysis of the tests revealed reduced reliability for holistic face processing tests in prosopagnosics. To our knowledge, this is the first study to show that prosopagnosics showed a significantly reduced reliability coefficient (Cronbach’s alpha) in the CFMT compared to the controls. We suggest that compensatory strategies employed by the prosopagnosics might be the cause for the vast variety of response patterns revealed by the reduced test reliability. This finding raises the question whether classical face tests measure the same perceptual processes in controls and prosopagnosics. PMID:27482369

Procedures for central auditory processing screening in schoolchildren.

PubMed

Carvalho, Nádia Giulian de; Ubiali, Thalita; Amaral, Maria Isabel Ramos do; Santos, Maria Francisca Colella

2018-03-22

Central auditory processing screening in schoolchildren has led to debates in literature, both regarding the protocol to be used and the importance of actions aimed at prevention and promotion of auditory health. Defining effective screening procedures for central auditory processing is a challenge in Audiology. This study aimed to analyze the scientific research on central auditory processing screening and discuss the effectiveness of the procedures utilized. A search was performed in the SciELO and PUBMed databases by two researchers. The descriptors used in Portuguese and English were: auditory processing, screening, hearing, auditory perception, children, auditory tests and their respective terms in Portuguese. original articles involving schoolchildren, auditory screening of central auditory skills and articles in Portuguese or English. studies with adult and/or neonatal populations, peripheral auditory screening only, and duplicate articles. After applying the described criteria, 11 articles were included. At the international level, central auditory processing screening methods used were: screening test for auditory processing disorder and its revised version, screening test for auditory processing, scale of auditory behaviors, children's auditory performance scale and Feather Squadron. In the Brazilian scenario, the procedures used were the simplified auditory processing assessment and Zaidan's battery of tests. At the international level, the screening test for auditory processing and Feather Squadron batteries stand out as the most comprehensive evaluation of hearing skills. At the national level, there is a paucity of studies that use methods evaluating more than four skills, and are normalized by age group. The use of simplified auditory processing assessment and questionnaires can be complementary in the search for an easy access and low-cost alternative in the auditory screening of Brazilian schoolchildren. Interactive tools should be proposed, that allow the selection of as many hearing skills as possible, validated by comparison with the battery of tests used in the diagnosis. Copyright © 2018 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

Approximating the r-Process on Earth with Thermonuclear Explosions. Lessons Learned and Unanswered Questions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Becker, Stephen Allan

2016-01-28

During the astrophysical r-process, multiple neutron captures occur so rapidly on target nuclei that their daughter nuclei generally do not have time to undergo radioactive decay before another neutron is captured. The r-process can be approximately simulated on Earth in certain types of thermonuclear explosions through an analogous process of rapid neutron captures known as the "prompt capture" process. Between 1952 and 1969, 23 nuclear tests were fielded by the US which were involved (at least partially) with the "prompt capture" process. Of these tests, 15 were at least partially successful. Some of these tests were conducted under the Plowsharemore » Peaceful Nuclear Explosion Program as scientific research experiments. It is now known that the USSR conducted similar nuclear tests during 1966 to 1979. The elements einsteinium and fermium were first discovered by this process. The most successful tests achieved 19 successive neutron captures on the initial target nuclei. A review of the US program, target nuclei used, heavy element yields, scientific achievements of the program, and how some of the results have been used by the astrophysical community is given. Finally, some unanswered questions concerning very neutron-rich nuclei that could potentially have been answered with additional nuclear experiments is presented.« less

KSC-2014-4149

NASA Image and Video Library

2014-09-25

CAPE CANAVERAL, Fla. – Coupled Florida East Coast Railway, or FEC, locomotives No. 433 and No. 428 make the first run past the Orbiter Processing Facility and Thermal Protection System Facility in Launch Complex 39 at NASA’s Kennedy Space Center in Florida during the Rail Vibration Test for the Canaveral Port Authority. Seismic monitors are collecting data as the train passes by. The purpose of the test is to collect amplitude, frequency and vibration test data utilizing two Florida East Coast locomotives operating on KSC tracks to ensure that future railroad operations will not affect launch vehicle processing at the center. Buildings instrumented for the test include the Rotation Processing Surge Facility, Thermal Protection Systems Facility, Vehicle Assembly Building, Orbiter Processing Facility and Booster Fabrication Facility. Photo credit: NASA/Daniel Casper

MEASUREMENT OF INDOOR AIR EMISSIONS FROM DRY-PROCESS PHOTOCOPY MACHINES

EPA Science Inventory

The article provides background information on indoor air emissions from office equipment, with emphasis on dry-process photocopy machines. The test method is described in detail along with results of a study to evaluate the test method using four dry-process photocopy machines. ...

The Henry Ford Production System: LEAN Process Redesign Improves Service in the Molecular Diagnostic Laboratory

PubMed Central

Cankovic, Milena; Varney, Ruan C.; Whiteley, Lisa; Brown, Ron; D'Angelo, Rita; Chitale, Dhananjay; Zarbo, Richard J.

2009-01-01

Accurate and timely molecular test results play an important role in patient management; consequently, there is a customer expectation of short testing turnaround times. Baseline data analysis revealed that the greatest challenge to timely result generation occurred in the preanalytic phase of specimen collection and transport. Here, we describe our efforts to improve molecular testing turnaround times by focusing primarily on redesign of preanalytic processes using the principles of LEAN production. Our goal was to complete greater than 90% of the molecular tests in less than 3 days. The project required cooperation from different laboratory disciplines as well as individuals outside of the laboratory. The redesigned processes involved defining and standardizing the protocols and approaching blood and tissue specimens as analytes for molecular testing. The LEAN process resulted in fewer steps, approaching the ideal of a one-piece flow for specimens through collection/retrieval, transport, and different aspects of the testing process. The outcome of introducing the LEAN process has been a 44% reduction in molecular test turnaround time for tissue specimens, from an average of 2.7 to 1.5 days. In addition, extending LEAN work principles to the clinician suppliers has resulted in a markedly increased number of properly collected and shipped blood specimens (from 50 to 87%). These continuous quality improvements were accomplished by empowered workers in a blame-free environment and are now being sustained with minimal management involvement. PMID:19661386

Avoiding Assessment Anarchy. Quality Test Administration Strategies: Communicate Expectations, Reduce Variation, Increase Quality, Improve Relationships, Reward Excellence, Recognize Success.

ERIC Educational Resources Information Center

Matter, M. Kevin

This paper presents strategies that address the needs of the school district assessment office for standardized procedures to support reliable and efficient test processing and reporting and that meet the needs of school staff for test administration guidelines. The key to test administration and processing quality is a knowledgeable test…

New method for rapid testing of bond strength for wood adhesives

Treesearch

James M. Wescott; Michael J. Birkeland; Amy E. Traska; Charles R. Frihart; Brice N. Dally

2007-01-01

In developing new adhesives for wood bonding, the testing of bond performance can often be a limiting factor in the development process. Evaluating the bond performance of an adhesive that can be prepared in less than a day often takes several days using standard performance tests. This testing slows the development process and may cause a company to abandon a...

Design of experiments enhanced statistical process control for wind tunnel check standard testing

NASA Astrophysics Data System (ADS)

Phillips, Ben D.

The current wind tunnel check standard testing program at NASA Langley Research Center is focused on increasing data quality, uncertainty quantification and overall control and improvement of wind tunnel measurement processes. The statistical process control (SPC) methodology employed in the check standard testing program allows for the tracking of variations in measurements over time as well as an overall assessment of facility health. While the SPC approach can and does provide researchers with valuable information, it has certain limitations in the areas of process improvement and uncertainty quantification. It is thought by utilizing design of experiments methodology in conjunction with the current SPC practices that one can efficiently and more robustly characterize uncertainties and develop enhanced process improvement procedures. In this research, methodologies were developed to generate regression models for wind tunnel calibration coefficients, balance force coefficients and wind tunnel flow angularities. The coefficients of these regression models were then tracked in statistical process control charts, giving a higher level of understanding of the processes. The methodology outlined is sufficiently generic such that this research can be applicable to any wind tunnel check standard testing program.

Robust non-parametric one-sample tests for the analysis of recurrent events.

PubMed

Rebora, Paola; Galimberti, Stefania; Valsecchi, Maria Grazia

2010-12-30

One-sample non-parametric tests are proposed here for inference on recurring events. The focus is on the marginal mean function of events and the basis for inference is the standardized distance between the observed and the expected number of events under a specified reference rate. Different weights are considered in order to account for various types of alternative hypotheses on the mean function of the recurrent events process. A robust version and a stratified version of the test are also proposed. The performance of these tests was investigated through simulation studies under various underlying event generation processes, such as homogeneous and nonhomogeneous Poisson processes, autoregressive and renewal processes, with and without frailty effects. The robust versions of the test have been shown to be suitable in a wide variety of event generating processes. The motivating context is a study on gene therapy in a very rare immunodeficiency in children, where a major end-point is the recurrence of severe infections. Robust non-parametric one-sample tests for recurrent events can be useful to assess efficacy and especially safety in non-randomized studies or in epidemiological studies for comparison with a standard population. Copyright © 2010 John Wiley & Sons, Ltd.

Individual Differences in Behavioral and Electrophysiological Measures of Binaural Processing Across the Adult Life Span.

PubMed

Roup, Christina M; Leigh, Elizabeth D

2015-06-01

The purpose of the present study was to examine individual differences in binaural processing across the adult life span. Sixty listeners (aged 23-80 years) with symmetrical hearing were tested. Binaural behavioral processing was measured by the Words-in-Noise Test, the 500-Hz masking level difference, and the Dichotic Digit Test. Electrophysiologic responses were assessed by the auditory middle latency response binaural interaction component. No correlations among binaural measures were found. Age accounted for the greatest amount of variability in speech-in-noise performance. Age was significantly correlated with the Words-in-Noise Test binaural advantage and dichotic ear advantage. Partial correlations, however, revealed that this was an effect of hearing status rather than age per se. Inspection of individual results revealed that 20% of listeners demonstrated reduced binaural performance for at least 2 of the binaural measures. The lack of significant correlations among variables suggests that each is an important measurement of binaural abilities. For some listeners, binaural processing was abnormal, reflecting a binaural processing deficit not identified by monaural audiologic tests. The inclusion of a binaural test battery in the audiologic evaluation is supported given that these listeners may benefit from alternative forms of audiologic rehabilitation.

Corps of Engineers National Automation Team (CENAT) Technology Transfer Test Bed (T(3)B) Demonstration of the Design 4D Program

DTIC Science & Technology

1989-11-01

other design tools. RESULTS OF TEST/DEMONSTRATION: Training for the Design 4D Program was conducted at USACERL. Although nearly half of the test...subjects had difficulty with the prompts, their understanding of the program improved after experimenting with the commands. After training , most felt...Equipment Testing Process 3 TEST DISTRICT TRAINING ........................................... 10 Training Process Post Training Survey Post Training

Development of Partial Discharging Simulation Test Equipment

NASA Astrophysics Data System (ADS)

Kai, Xue; Genghua, Liu; Yan, Jia; Ziqi, Chai; Jian, Lu

2017-12-01

In the case of partial discharge training for recruits who lack of on-site work experience, the risk of physical shock and damage of the test equipment may be due to the limited skill level and improper operation by new recruits. Partial discharge simulation tester is the use of simulation technology to achieve partial discharge test process simulation, relatively true reproduction of the local discharge process and results, so that the operator in the classroom will be able to get familiar with and understand the use of the test process and equipment.The teacher sets up the instrument to display different partial discharge waveforms so that the trainees can analyze the test results of different partial discharge types.

The auditory processing battery: survey of common practices.

PubMed

Emanuel, Diana C

2002-02-01

A survey of auditory processing (AP) diagnostic practices was mailed to all licensed audiologists in the State of Maryland and sent as an electronic mail attachment to the American Speech-Language-Hearing Association and Educational Audiology Association Internet forums. Common AP protocols (25 from the Internet, 28 from audiologists in Maryland) included requiring basic audiologic testing, using questionnaires, and administering dichotic listening, monaural low-redundancy speech, temporal processing, and electrophysiologic tests. Some audiologists also administer binaural interaction, attention, memory, and speech-language/psychological/educational tests and incorporate a classroom observation. The various AP batteries presently administered appear to be based on the availability of AP tests with well-documented normative data. Resources for obtaining AP tests are listed.

The Internet Process Addiction Test: Screening for Addictions to Processes Facilitated by the Internet

PubMed Central

Northrup, Jason C.; Lapierre, Coady; Kirk, Jeffrey; Rae, Cosette

2015-01-01

The Internet Process Addiction Test (IPAT) was created to screen for potential addictive behaviors that could be facilitated by the internet. The IPAT was created with the mindset that the term “Internet addiction” is structurally problematic, as the Internet is simply the medium that one uses to access various addictive processes. The role of the internet in facilitating addictions, however, cannot be minimized. A new screening tool that effectively directed researchers and clinicians to the specific processes facilitated by the internet would therefore be useful. This study shows that the Internet Process Addiction Test (IPAT) demonstrates good validity and reliability. Four addictive processes were effectively screened for with the IPAT: Online video game playing, online social networking, online sexual activity, and web surfing. Implications for further research and limitations of the study are discussed. PMID:26226007

The Internet Process Addiction Test: Screening for Addictions to Processes Facilitated by the Internet.

PubMed

Northrup, Jason C; Lapierre, Coady; Kirk, Jeffrey; Rae, Cosette

2015-07-28

The Internet Process Addiction Test (IPAT) was created to screen for potential addictive behaviors that could be facilitated by the internet. The IPAT was created with the mindset that the term "Internet addiction" is structurally problematic, as the Internet is simply the medium that one uses to access various addictive processes. The role of the internet in facilitating addictions, however, cannot be minimized. A new screening tool that effectively directed researchers and clinicians to the specific processes facilitated by the internet would therefore be useful. This study shows that the Internet Process Addiction Test (IPAT) demonstrates good validity and reliability. Four addictive processes were effectively screened for with the IPAT: Online video game playing, online social networking, online sexual activity, and web surfing. Implications for further research and limitations of the study are discussed.

Development of CFC-Free Cleaning Processes at the NASA White Sands Test Facility

NASA Technical Reports Server (NTRS)

Beeson, Harold; Kirsch, Mike; Hornung, Steven; Biesinger, Paul

1995-01-01

The NASA White Sands Test Facility (WSTF) is developing cleaning and verification processes to replace currently used chlorofluorocarbon-113- (CFC-113-) based processes. The processes being evaluated include both aqueous- and solvent-based techniques. The presentation will include the findings of investigations of aqueous cleaning and verification processes that are based on a draft of a proposed NASA Kennedy Space Center (KSC) cleaning procedure. Verification testing with known contaminants, such as hydraulic fluid and commonly used oils, established correlations between nonvolatile residue and CFC-113. Recoveries ranged from 35 to 60 percent of theoretical. WSTF is also investigating enhancements to aqueous sampling for organics and particulates. Although aqueous alternatives have been identified for several processes, a need still exists for nonaqueous solvent cleaning, such as the cleaning and cleanliness verification of gauges used for oxygen service. The cleaning effectiveness of tetrachloroethylene (PCE), trichloroethylene (TCE), ethanol, hydrochlorofluorocarbon-225 (HCFC-225), tert-butylmethylether, and n-Hexane was evaluated using aerospace gauges and precision instruments and then compared to the cleaning effectiveness of CFC-113. Solvents considered for use in oxygen systems were also tested for oxygen compatibility using high-pressure oxygen autoignition and liquid oxygen mechanical impact testing.

Design of video processing and testing system based on DSP and FPGA

NASA Astrophysics Data System (ADS)

Xu, Hong; Lv, Jun; Chen, Xi'ai; Gong, Xuexia; Yang, Chen'na

2007-12-01

Based on high speed Digital Signal Processor (DSP) and Field Programmable Gate Array (FPGA), a video capture, processing and display system is presented, which is of miniaturization and low power. In this system, a triple buffering scheme was used for the capture and display, so that the application can always get a new buffer without waiting; The Digital Signal Processor has an image process ability and it can be used to test the boundary of workpiece's image. A video graduation technology is used to aim at the position which is about to be tested, also, it can enhance the system's flexibility. The character superposition technology realized by DSP is used to display the test result on the screen in character format. This system can process image information in real time, ensure test precision, and help to enhance product quality and quality management.

Self-Regulation Principles Underlying Risk Perception and Decision Making within the Context of Genomic Testing

PubMed Central

Cameron, Linda D.; Biesecker, Barbara Bowles; Peters, Ellen; Taber, Jennifer M.; Klein, William M. P.

2017-01-01

Advances in theory and research on self-regulation and decision-making processes have yielded important insights into how cognitive, emotional, and social processes shape risk perceptions and risk-related decisions. We examine how self-regulation theory can be applied to inform our understanding of decision-making processes within the context of genomic testing, a clinical arena in which individuals face complex risk information and potentially life-altering decisions. After presenting key principles of self-regulation, we present a genomic testing case example to illustrate how principles related to risk representations, approach and avoidance motivations, emotion regulation, defensive responses, temporal construals, and capacities such as numeric abilities can shape decisions and psychological responses during the genomic testing process. We conclude with implications for using self-regulation theory to advance science within genomic testing and opportunities for how this research can inform further developments in self-regulation theory. PMID:29225669

Self-Regulation Principles Underlying Risk Perception and Decision Making within the Context of Genomic Testing.

PubMed

Cameron, Linda D; Biesecker, Barbara Bowles; Peters, Ellen; Taber, Jennifer M; Klein, William M P

2017-05-01

Advances in theory and research on self-regulation and decision-making processes have yielded important insights into how cognitive, emotional, and social processes shape risk perceptions and risk-related decisions. We examine how self-regulation theory can be applied to inform our understanding of decision-making processes within the context of genomic testing, a clinical arena in which individuals face complex risk information and potentially life-altering decisions. After presenting key principles of self-regulation, we present a genomic testing case example to illustrate how principles related to risk representations, approach and avoidance motivations, emotion regulation, defensive responses, temporal construals, and capacities such as numeric abilities can shape decisions and psychological responses during the genomic testing process. We conclude with implications for using self-regulation theory to advance science within genomic testing and opportunities for how this research can inform further developments in self-regulation theory.

Energy Systems Test Area (ESTA) Battery Test Operations User Test Planning Guide

NASA Technical Reports Server (NTRS)

Salinas, Michael

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the ESTA Battery Test Operations. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

One process is not enough! A speed-accuracy tradeoff study of recognition memory.

PubMed

Boldini, Angela; Russo, Riccardo; Avons, S E

2004-04-01

Speed-accuracy tradeoff (SAT) methods have been used to contrast single- and dual-process accounts of recognition memory. In these procedures, subjects are presented with individual test items and are required to make recognition decisions under various time constraints. In this experiment, we presented word lists under incidental learning conditions, varying the modality of presentation and level of processing. At test, we manipulated the interval between each visually presented test item and a response signal, thus controlling the amount of time available to retrieve target information. Study-test modality match had a beneficial effect on recognition accuracy at short response-signal delays (< or =300 msec). Conversely, recognition accuracy benefited more from deep than from shallow processing at study only at relatively long response-signal delays (> or =300 msec). The results are congruent with views suggesting that both fast familiarity and slower recollection processes contribute to recognition memory.

Determining the compactive effort required to model pavement voids using the Corps of Engineers gyratory testing machine.

DOT National Transportation Integrated Search

1997-11-01

Various agencies have used the Corps of Engineers gyratory testing machine (GTM) to design and test asphalt mixes. Materials properties such as shear strength and strain are measured during the compaction process. However, a compaction process duplic...

Memory for pictures and words as a function of level of processing: Depth or dual coding?

PubMed

D'Agostino, P R; O'Neill, B J; Paivio, A

1977-03-01

The experiment was designed to test differential predictions derived from dual-coding and depth-of-processing hypotheses. Subjects under incidental memory instructions free recalled a list of 36 test events, each presented twice. Within the list, an equal number of events were assigned to structural, phonemic, and semantic processing conditions. Separate groups of subjects were tested with a list of pictures, concrete words, or abstract words. Results indicated that retention of concrete words increased as a direct function of the processing-task variable (structural < phonemic

Recycled poly(ethylene terephthalate) for direct food contact applications: challenge test of an inline recycling process.

PubMed

Franz, R; Welle, F

2002-05-01

Of all the plastics used for packaging, due to its low diffusivity and chemical inertness, poly(ethylene terephthalate) (PET) is one of the favoured candidate plastics for closed-loop recycling for new packaging applications. In the work reported here, a PET-recycling process was investigated with respect to its cleaning efficiency and compliance of the PET recyclate with food law. The key technology of the investigated PET-recycling process to remove contaminants consists of a predecontamination-extruder combination. At the end of the recycling process, there is either a pelletizing system or downstream equipment to produce preforms or flat sheets. Therefore, the process has two process options, an inline production of PET preforms and a batch option producing PET pellets. In the case of possible misuse of PET bottles by the consumer, the inline process produces higher concentrations in the bottle wall of the recyclate containing preforms. Owing to the dilution of the PET output material by large amounts of uncontaminated PET, the batch option is the less critical process in terms of consumer protection. Regarding an appropriate testing procedure for the evaluation of a bottle-to-bottle recycling process, both process options have their own specific requirements with respect to the design of a challenge test. A novel challenge test approach to the inline mode of a recycling process is presented here.

SED16 autonomous star tracker night sky testing

NASA Astrophysics Data System (ADS)

Foisneau, Thierry; Piriou, Véronique; Perrimon, Nicolas; Jacob, Philippe; Blarre, Ludovic; Vilaire, Didier

2017-11-01

The SED16 is an autonomous multi-missions star tracker which delivers three axis satellite attitude in an inertial reference frame and the satellite angular velocity with no prior information. The qualification process of this star sensor includes five validation steps using optical star simulator, digitized image simulator and a night sky tests setup. The night sky testing was the final step of the qualification process during which all the functions of the star tracker were used in almost nominal conditions : Autonomous Acquisition of the attitude, Autonomous Tracking of ten stars. These tests were performed in Calern in the premises of the OCA (Observatoire de la Cote d'Azur). The test set-up and the test results are described after a brief review of the sensor main characteristics and qualification process.

Cardiac examination and the effect of dual-processing instruction in a cardiopulmonary simulator.

PubMed

Sibbald, Matt; McKinney, James; Cavalcanti, Rodrigo B; Yu, Eric; Wood, David A; Nair, Parvathy; Eva, Kevin W; Hatala, Rose

2013-08-01

Use of dual-processing has been widely touted as a strategy to reduce diagnostic error in clinical medicine. However, this strategy has not been tested among medical trainees with complex diagnostic problems. We sought to determine whether dual-processing instruction could reduce diagnostic error across a spectrum of experience with trainees undertaking cardiac physical exam. Three experiments were conducted using a similar design to teach cardiac physical exam using a cardiopulmonary simulator. One experiment was conducted in each of three groups: experienced, intermediate and novice trainees. In all three experiments, participants were randomized to receive undirected or dual-processing verbal instruction during teaching, practice and testing phases. When tested, dual-processing instruction did not change the probability assigned to the correct diagnosis in any of the three experiments. Among intermediates, there was an apparent interaction between the diagnosis tested and the effect of dual-processing instruction. Among relative novices, dual processing instruction may have dampened the harmful effect of a bias away from the correct diagnosis. Further work is needed to define the role of dual-processing instruction to reduce cognitive error. This study suggests that it cannot be blindly applied to complex diagnostic problems such as cardiac physical exam.

Improving financial performance by modeling and analysis of radiology procedure scheduling at a large community hospital.

PubMed

Lu, Lingbo; Li, Jingshan; Gisler, Paula

2011-06-01

Radiology tests, such as MRI, CT-scan, X-ray and ultrasound, are cost intensive and insurance pre-approvals are necessary to get reimbursement. In some cases, tests may be denied for payments by insurance companies due to lack of pre-approvals, inaccurate or missing necessary information. This can lead to substantial revenue losses for the hospital. In this paper, we present a simulation study of a centralized scheduling process for outpatient radiology tests at a large community hospital (Central Baptist Hospital in Lexington, Kentucky). Based on analysis of the central scheduling process, a simulation model of information flow in the process has been developed. Using such a model, the root causes of financial losses associated with errors and omissions in this process were identified and analyzed, and their impacts were quantified. In addition, "what-if" analysis was conducted to identify potential process improvement strategies in the form of recommendations to the hospital leadership. Such a model provides a quantitative tool for continuous improvement and process control in radiology outpatient test scheduling process to reduce financial losses associated with process error. This method of analysis is also applicable to other departments in the hospital.

Antenna Test Facility (ATF): User Test Planning Guide

NASA Technical Reports Server (NTRS)

Lin, Greg

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the ATF. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Radiant Heat Test Facility (RHTF): User Test Planning Guide

NASA Technical Reports Server (NTRS)

DelPapa, Steven

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the RHTF. The User Test Planning Guide aids in establishing expectations for both NASA and non- NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Electronic Systems Test Laboratory (ESTL) User Test Planning Guide

NASA Technical Reports Server (NTRS)

Robinson, Neil

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the ESTL. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Structures Test Laboratory (STL). User Test Planning Guide

NASA Technical Reports Server (NTRS)

Zipay, John J.

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the STL. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Validation of contractor HMA testing data in the materials acceptance process - phase II : final report.

DOT National Transportation Integrated Search

2016-08-01

This study conducted an analysis of the SCDOT HMA specification. A Research Steering Committee provided oversight : of the process. The research process included extensive statistical analyses of test data supplied by SCDOT. : A total of 2,789 AC tes...

Fidelity of test development process within a national science grant

NASA Astrophysics Data System (ADS)

Brumfield, Teresa E.

In 2002, a math-science partnership (MSP) program was initiated by a national science grant. The purpose of the MSP program was to promote the development, implementation, and sustainability of promising partnerships among institutions of higher education, K-12 schools and school systems, as well as other important stakeholders. One of the funded projects included a teacher-scientist collaborative that instituted a professional development system to prepare teachers to use inquiry-based instructional modules. The MSP program mandated evaluations of its funded projects. One of the teacher-scientist collaborative project's outcomes specifically focused on teacher and student science content and process skills. In order to provide annual evidence of progress and to measure the impact of the project's efforts, and because no appropriate science tests were available to measure improvements in content knowledge of participating teachers and their students, the project contracted for the development of science tests. This dissertation focused on the process of test development within an evaluation and examined planned (i.e., expected) and actual (i.e., observed) test development, specifically concentrating on the factors that affected the actual test development process. Planned test development was defined as the process of creating tests according to the well-established test development procedures recommended by the AERA/APA/NCME 1999 Standards for Educational and Psychological Testing. Actual test development was defined as the process of creating tests as it actually took place. Because case study provides an in-depth, longitudinal examination of an event (i.e., case) in a naturalistic setting, it was selected as the appropriate methodology to examine the difference between planned and actual test development. The case (or unit of analysis) was the test development task, a task that was bounded by the context in which it occurred---and over which this researcher had no control---and by time. The purpose for studying the case was to gain a more in-depth, holistic understanding of the real-life test development task that took place within a project evaluation context. In particular, this case study investigated how the actual test development process was affected by: (1) the national and state (i.e., NC) science standards, (2) the NSF's definition of "evidence" in a project evaluation, (3) the MSP project's understanding of the role of the to-be-developed tests in their project evaluation, (4) the MSP project's understanding of the test development process, and (5) the MSP project's participants (e.g., teacher item-writers and scientists). From an investigation of this case, it was concluded that: (a) constructing psychometrically sound tests within an evaluation is not easy, (b) sufficient time and resources to construct such measures properly are seldom provided, and (c) test construction---at least within an evaluation---is not routine and unproblematic. Based upon the results from this case study, it was recommended that stakeholders (i.e., program managers, project directors, and evaluators) be familiar with the steps and standards used to develop psychometrically sound tests. Additionally, it was recommended that, for future research, a meta-analysis that examines only the test development process be conducted of all other MSP projects. A second suggested future research area was to establish a protocol that provides a systematic means by which to examine an existing or proposed MSP project for alignment with state science standards. Such a protocol would be cost-effective in that demonstrated alignment with state science standards would enable projects to use existing state science assessments, which must be in place, according to NCLB, by the 2007-2008 school year, to demonstrate student achievement. In this way, project directors and evaluators, typically with limited familiarity with the steps and standards by which psychometrically sound assessments are created, would not be placed in the role of test developer.

Aging of theory of mind: the influence of educational level and cognitive processing.

PubMed

Li, Xiaoming; Wang, Kai; Wang, Fan; Tao, Qian; Xie, Yu; Cheng, Qi

2013-01-01

Previous studies of theory of mind (ToM) in old age have provided mixed results. We predicted that educational level and cognitive processing are two factors influencing the pattern of the aging of ToM. To test this hypothesis, a younger group who received higher education (mean age 20.46 years), an older group with an education level equal to that of the young group (mean age 76.29 years), and an older group with less education (mean age 73.52 years) were recruited. ToM tasks included the following tests: the second-order false-belief task, the faux-pas task, the eyes test, and tests of fundamental aspects of cognitive function that included two background tests (memory span and processing speed) and three subcomponents of executive function (inhibition, updating, and shifting). We found that the younger group and the older group with equally high education outperformed the older group with less education in false-belief and faux-pas tasks. However, there was no significant difference between the two former groups. The three groups of participants performed equivalently in the eyes test as well as in control tasks (false-belief control question, faux-pas control question, faux-pas control story, and Eyes Test control task). The younger group outperformed the other two groups in the cognitive processing tasks. Mediation analyses showed that difficulties in inhibition, memory span, and processing speed mediated the age differences in false-belief reasoning. Also, the variables of inhibition, updating, memory span, and processing speed mediated age-related variance in faux-pas. Discussion focused on the links between ToM aging, educational level, and cognitive processing. Supported by Chinese National Natural Science Foundation (number: 30870766) and Anhui Province Natural Science Foundation (number: 11040606M166).

Using Multi-Objective Genetic Programming to Synthesize Stochastic Processes

NASA Astrophysics Data System (ADS)

Ross, Brian; Imada, Janine

Genetic programming is used to automatically construct stochastic processes written in the stochastic π-calculus. Grammar-guided genetic programming constrains search to useful process algebra structures. The time-series behaviour of a target process is denoted with a suitable selection of statistical feature tests. Feature tests can permit complex process behaviours to be effectively evaluated. However, they must be selected with care, in order to accurately characterize the desired process behaviour. Multi-objective evaluation is shown to be appropriate for this application, since it permits heterogeneous statistical feature tests to reside as independent objectives. Multiple undominated solutions can be saved and evaluated after a run, for determination of those that are most appropriate. Since there can be a vast number of candidate solutions, however, strategies for filtering and analyzing this set are required.

Coordination and organization of security software process for power information application environment

NASA Astrophysics Data System (ADS)

Wang, Qiang

2017-09-01

As an important part of software engineering, the software process decides the success or failure of software product. The design and development feature of security software process is discussed, so is the necessity and the present significance of using such process. Coordinating the function software, the process for security software and its testing are deeply discussed. The process includes requirement analysis, design, coding, debug and testing, submission and maintenance. In each process, the paper proposed the subprocesses to support software security. As an example, the paper introduces the above process into the power information platform.

Development and application of an acceptance testing model

NASA Technical Reports Server (NTRS)

Pendley, Rex D.; Noonan, Caroline H.; Hall, Kenneth R.

1992-01-01

The process of acceptance testing large software systems for NASA has been analyzed, and an empirical planning model of the process constructed. This model gives managers accurate predictions of the staffing needed, the productivity of a test team, and the rate at which the system will pass. Applying the model to a new system shows a high level of agreement between the model and actual performance. The model also gives managers an objective measure of process improvement.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Weizhao; Ren, Huaqing; Lu, Jie

This paper reports several characterization methods of the properties of the uncured woven prepreg during the preforming process. The uniaxial tension, bias-extension, and bending tests are conducted to measure the in-plane properties of the material. The friction tests utilized to reveal the prepreg-prepreg and prepreg-forming tool interactions. All these tests are performed within the temperature range of the real manufacturing process. The results serve as the inputs to the numerical simulation for the product prediction and preforming process parameter optimization.

Testing linen disinfection procedures in practice with phage-charged-bioindicators.

PubMed

Gerhardts, Anja; Mucha, Helmut; Höfer, Dirk

2012-01-01

Disinfecting laundry processes are essential to avoid contamination of laundering machines and linen during commercial laundry reprocessing in the health care sector. Recently a bacteriophage-charged bioindicator has been developed using MS2 as surrogate virus for testing of low-temperature disinfecting laundry processing on efficacy against viruses related to practice. This paper therefore aims to investigate application of MS2-bioindicators in chemothermal processes under practical conditions (phase 2/step 2) and in practice (phase 3). The experimental design was developed and modified according to the German Society for Hygiene and Microbiology (DGHM) Standard Methods for Testing Chemical Disinfection Processes. Tests under practical conditions were performed at 60 degrees C and 70 degrees C. Additional tests in tunnel washers were carried out at 60 degrees C and 70 degrees C. In all experiments validated disinfecting laundry processes, recommended for bactericidal and virucidal performance (categories A and B), were applied. The results show a temperature-dependent gradual efficacy against the test virus MS2 up to reduction values of more than 8 log10-steps. Therefore MS2-bioindicators prove to be suitable as a tool to determine the performance of disinfection procedures against viruses in practice. Phage-charged bioindicators may be a tool to provide further insights into the reliability of antiviral laundry processes for health care quality management and for infection control.

Estimating Missing Unit Process Data in Life Cycle Assessment Using a Similarity-Based Approach.

PubMed

Hou, Ping; Cai, Jiarui; Qu, Shen; Xu, Ming

2018-05-01

In life cycle assessment (LCA), collecting unit process data from the empirical sources (i.e., meter readings, operation logs/journals) is often costly and time-consuming. We propose a new computational approach to estimate missing unit process data solely relying on limited known data based on a similarity-based link prediction method. The intuition is that similar processes in a unit process network tend to have similar material/energy inputs and waste/emission outputs. We use the ecoinvent 3.1 unit process data sets to test our method in four steps: (1) dividing the data sets into a training set and a test set; (2) randomly removing certain numbers of data in the test set indicated as missing; (3) using similarity-weighted means of various numbers of most similar processes in the training set to estimate the missing data in the test set; and (4) comparing estimated data with the original values to determine the performance of the estimation. The results show that missing data can be accurately estimated when less than 5% data are missing in one process. The estimation performance decreases as the percentage of missing data increases. This study provides a new approach to compile unit process data and demonstrates a promising potential of using computational approaches for LCA data compilation.

40 CFR 65.164 - Performance test and flare compliance determination notifications and reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas System or a Process § 65.164 Performance test and flare... complete test report shall include a brief process description, sampling site description, description of...

Sensitizing Undergraduates to Potential Inaccuracies in Projective Test Interpretation.

ERIC Educational Resources Information Center

Barret, Robert L.; Wachowiak, Dale G.

This paper describes a methodology developed to provide undergraduate students with direct experience in the process of impressionistic test interpretation. In the experiential exercise, students were shown Thematic Apperception Test cards and then read the responses given by an anonymous client. A discussion of the process by which the students…

Using Knowledge Management to Revise Software-Testing Processes

ERIC Educational Resources Information Center

Nogeste, Kersti; Walker, Derek H. T.

2006-01-01

Purpose: This paper aims to use a knowledge management (KM) approach to effectively revise a utility retailer's software testing process. This paper presents a case study of how the utility organisation's customer services IT production support group improved their test planning skills through applying the American Productivity and Quality Center…

Development of The Science Processes Test.

ERIC Educational Resources Information Center

Ludeman, Robert R.

Presented is a description and copy of a test manual developed to include items in the test on the basis of children's performance; each item correlated highly with performance on an external criterion. The external criterion was the Individual Competency Measures of the elementary science program Science - A Process Approach (SAPA). The test…

Process test plan, phase II: waste retrieval sluicing system emissions collection

DOE Office of Scientific and Technical Information (OSTI.GOV)

POWERS, R.L.

1999-06-01

This Process Test Plan is prepared to continue from HNF-3733 which was Phase I of the test. Supplemental operational controls and sampling requirements are defined to safely obtain gas samples from the 296-C-006 ventilation system stack during active operation of the sluicing equipment.

49 CFR 40.83 - How do laboratories process incoming specimens?

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.83 How do laboratories... copies of the CCF or any copies of the alcohol testing form. (b) You must comply with applicable provisions of the HHS Guidelines concerning accessioning and processing urine drug specimens. (c) You must...

49 CFR 40.83 - How do laboratories process incoming specimens?

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.83 How do laboratories... copies of the CCF or any copies of the alcohol testing form. (b) You must comply with applicable provisions of the HHS Guidelines concerning accessioning and processing urine drug specimens. (c) You must...

49 CFR 40.83 - How do laboratories process incoming specimens?

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.83 How do laboratories... copies of the CCF or any copies of the alcohol testing form. (b) You must comply with applicable provisions of the HHS Guidelines concerning accessioning and processing urine drug specimens. (c) You must...

49 CFR 40.83 - How do laboratories process incoming specimens?

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.83 How do laboratories... copies of the CCF or any copies of the alcohol testing form. (b) You must comply with applicable provisions of the HHS Guidelines concerning accessioning and processing urine drug specimens. (c) You must...

49 CFR 40.83 - How do laboratories process incoming specimens?

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.83 How do laboratories... copies of the CCF or any copies of the alcohol testing form. (b) You must comply with applicable provisions of the HHS Guidelines concerning accessioning and processing urine drug specimens. (c) You must...

The Relation between Self-Selected Study Processes and Test Performance.

ERIC Educational Resources Information Center

Nist, Sherrie L.; And Others

1991-01-01

A correlational study examined the relationship between test performance and four study processes (encoding, word meaning, organizing, and executive control). Results with 123 college freshmen trained to use study strategies suggest that executive control is related to test performance and that trained subjects select a variety of strategies…

EVALUATION OF A TEST METHOD FOR MEASURING INDOOR AIR EMISSIONS FROM DRY-PROCESS PHOTOCOPIERS

EPA Science Inventory

A large chamber test method for measuring indoor air emissions from office equipment was developed, evaluated, and revised based on the initial testing of four dry-process photocopiers. Because all chambers may not necessarily produce similar results (e.g., due to differences in ...

Materials and processes laboratory composite materials characterization task, part 1. Damage tolerance

NASA Technical Reports Server (NTRS)

Nettles, A. T.; Tucker, D. S.; Patterson, W. J.; Franklin, S. W.; Gordon, G. H.; Hart, L.; Hodge, A. J.; Lance, D. G.; Russel, S. S.

1991-01-01

A test run was performed on IM6/3501-6 carbon-epoxy in which the material was processed, machined into specimens, and tested for damage tolerance capabilities. Nondestructive test data played a major role in this element of composite characterization. A time chart was produced showing the time the composite material spent within each Branch or Division in order to identify those areas which produce a long turnaround time. Instrumented drop weight testing was performed on the specimens with nondestructive evaluation being performed before and after the impacts. Destructive testing in the form of cross-sectional photomicrography and compression-after-impact testing were used. Results show that the processing and machining steps needed to be performed more rapidly if data on composite material is to be collected within a reasonable timeframe. The results of the damage tolerance testing showed that IM6/3501-6 is a brittle material that is very susceptible to impact damage.

Applying the Anderson-Darling test to suicide clusters: evidence of contagion at U. S. universities?

PubMed

MacKenzie, Donald W

2013-01-01

Suicide clusters at Cornell University and the Massachusetts Institute of Technology (MIT) prompted popular and expert speculation of suicide contagion. However, some clustering is to be expected in any random process. This work tested whether suicide clusters at these two universities differed significantly from those expected under a homogeneous Poisson process, in which suicides occur randomly and independently of one another. Suicide dates were collected for MIT and Cornell for 1990-2012. The Anderson-Darling statistic was used to test the goodness-of-fit of the intervals between suicides to distribution expected under the Poisson process. Suicides at MIT were consistent with the homogeneous Poisson process, while those at Cornell showed clustering inconsistent with such a process (p = .05). The Anderson-Darling test provides a statistically powerful means to identify suicide clustering in small samples. Practitioners can use this method to test for clustering in relevant communities. The difference in clustering behavior between the two institutions suggests that more institutions should be studied to determine the prevalence of suicide clustering in universities and its causes.

Systems Engineering, Quality and Testing

NASA Technical Reports Server (NTRS)

Shepherd, Christena C.

2015-01-01

AS9100 has little to say about how to apply a Quality Management System (QMS) to aerospace test programs. There is little in the quality engineering Body of Knowledge that applies to testing, unless it is nondestructive examination or some type of lab or bench testing. If one examines how the systems engineering processes are implemented throughout a test program; and how these processes can be mapped to AS9100, a number of areas for involvement of the quality professional are revealed.

Specialized Environmental Chamber Test Complex: User Test Planning Guide

NASA Technical Reports Server (NTRS)

Montz, Michael E.

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the Specialized Environmental Test Complex. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Electromagnetic Interference/Compatibility (EMI/EMC) Control Test and Measurement Facility: User Test Planning Guide

NASA Technical Reports Server (NTRS)

Scully, Robert C.

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the EMI/EMC Test Facility. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

MATTS- A Step Towards Model Based Testing

NASA Astrophysics Data System (ADS)

Herpel, H.-J.; Willich, G.; Li, J.; Xie, J.; Johansen, B.; Kvinnesland, K.; Krueger, S.; Barrios, P.

2016-08-01

In this paper we describe a Model Based approach to testing of on-board software and compare it with traditional validation strategy currently applied to satellite software. The major problems that software engineering will face over at least the next two decades are increasing application complexity driven by the need for autonomy and serious application robustness. In other words, how do we actually get to declare success when trying to build applications one or two orders of magnitude more complex than today's applications. To solve the problems addressed above the software engineering process has to be improved at least for two aspects: 1) Software design and 2) Software testing. The software design process has to evolve towards model-based approaches with extensive use of code generators. Today, testing is an essential, but time and resource consuming activity in the software development process. Generating a short, but effective test suite usually requires a lot of manual work and expert knowledge. In a model-based process, among other subtasks, test construction and test execution can also be partially automated. The basic idea behind the presented study was to start from a formal model (e.g. State Machines), generate abstract test cases which are then converted to concrete executable test cases (input and expected output pairs). The generated concrete test cases were applied to an on-board software. Results were collected and evaluated wrt. applicability, cost-efficiency, effectiveness at fault finding, and scalability.

A processing approach to the working memory/long-term memory distinction: evidence from the levels-of-processing span task.

PubMed

Rose, Nathan S; Craik, Fergus I M

2012-07-01

Recent theories suggest that performance on working memory (WM) tasks involves retrieval from long-term memory (LTM). To examine whether WM and LTM tests have common principles, Craik and Tulving's (1975) levels-of-processing paradigm, which is known to affect LTM, was administered as a WM task: Participants made uppercase, rhyme, or category-membership judgments about words, and immediate recall of the words was required after every 3 or 8 processing judgments. In Experiment 1, immediate recall did not demonstrate a levels-of-processing effect, but a subsequent LTM test (delayed recognition) of the same words did show a benefit of deeper processing. Experiment 2 showed that surprise immediate recall of 8-item lists did demonstrate a levels-of-processing effect, however. A processing account of the conditions in which levels-of-processing effects are and are not found in WM tasks was advanced, suggesting that the extent to which levels-of-processing effects are similar between WM and LTM tests largely depends on the amount of disruption to active maintenance processes. 2012 APA, all rights reserved

Effect of Speed of Processing Training on Older Driver Screening Measures.

PubMed

Eramudugolla, Ranmalee; Kiely, Kim M; Chopra, Sidhant; Anstey, Kaarin J

2017-01-01

Objective: Computerized training for cognitive enhancement is of great public interest, however, there is inconsistent evidence for the transfer of training gains to every day activity. Several large trials have focused on speed of processing (SOP) training with some promising findings for long-term effects on daily activity, but no immediate transfer to other cognitive tests. Here, we examine the transfer of SOP training gains to cognitive measures that are known predictors of driving safety in older adults. Methods: Fifty-three adults aged 65-87 years who were current drivers participated in a two group non-randomized design with repeated measures and a no-contact matched control group. The Intervention group completed an average of 7.9 ( SD = 3.0) hours of self-administered online SOP training at home. Control group was matched on age, gender and test-re-test interval. Measures included the Useful Field of View (UFOV) test, a Hazard Perception test, choice reaction time (Cars RT), Trail Making Test B, a Maze test, visual motion threshold, as well as road craft and road knowledge tests. Results: Speed of processing training resulted in significant improvement in processing speed on the UFOV test relative to controls, with an average change of -45.8 ms ( SE = 14.5), and effect size of ω 2 = 0.21. Performance on the Maze test also improved, but significant slowing on the Hazard Perception test was observed after SOP training. Training effects on the UFOV task was associated with similar effects on the Cars RT, but not the Hazard Perception and Maze tests, suggesting transfer to some but not all driving related measures. There were no effects of training on any of the other measures examined. Conclusion: Speed of processing training effects on the UFOV task can be achieved with self-administered, online training at home, with some transfer to other cognitive tests. However, differential effects of training may be observed for tasks requiring goal-directed search strategies rather than diffuse attention.

Processing Relative Clauses by Hungarian Typically Developing Children

ERIC Educational Resources Information Center

Kas, Bence; Lukacs, Agnes

2012-01-01

Hungarian is a language with morphological case marking and relatively free word order. These typological characteristics make it a good ground for testing the crosslinguistic validity of theories on processing sentences with relative clauses. Our study focused on effects of structural factors and processing capacity. We tested 43 typically…

40 CFR Table 8 to Subpart Sssss of... - Continuous Compliance with Operating Limits

Code of Federal Regulations, 2014 CFR

2014-07-01

... recent performance test; andii. Conducting annually an inspection of all duct work, vents, and capture... process operating parameters within the limits established during the most recent performance test i... processing rate at or below the maximum organic HAP processing rate established during the most recent...

40 CFR Table 8 to Subpart Sssss of... - Continuous Compliance with Operating Limits

Code of Federal Regulations, 2013 CFR

2013-07-01

... recent performance test; andii. Conducting annually an inspection of all duct work, vents, and capture... process operating parameters within the limits established during the most recent performance test i... processing rate at or below the maximum organic HAP processing rate established during the most recent...

40 CFR Table 8 to Subpart Sssss of... - Continuous Compliance with Operating Limits

Code of Federal Regulations, 2012 CFR

2012-07-01

... recent performance test; andii. Conducting annually an inspection of all duct work, vents, and capture... process operating parameters within the limits established during the most recent performance test i... processing rate at or below the maximum organic HAP processing rate established during the most recent...

Piagetian Cognitive Development and Primary Process Thinking in Children

ERIC Educational Resources Information Center

Wulach, James S.

1977-01-01

Thirty-seven middle-class white children, ages 5-8, were tested on eight Piagetian tasks and the Rorschach test, and divided into preoperational, transitional, and concrete operational groups. Measures of primary process vs. secondary process thinking were found to be related to the Piagetian stages of development. (GDC)

Autoverification process improvement by Six Sigma approach: Clinical chemistry & immunoassay.

PubMed

Randell, Edward W; Short, Garry; Lee, Natasha; Beresford, Allison; Spencer, Margaret; Kennell, Marina; Moores, Zoë; Parry, David

2018-05-01

This study examines effectiveness of a project to enhance an autoverification (AV) system through application of Six Sigma (DMAIC) process improvement strategies. Similar AV systems set up at three sites underwent examination and modification to produce improved systems while monitoring proportions of samples autoverified, the time required for manual review and verification, sample processing time, and examining characteristics of tests not autoverified. This information was used to identify areas for improvement and monitor the impact of changes. Use of reference range based criteria had the greatest impact on the proportion of tests autoverified. To improve AV process, reference range based criteria was replaced with extreme value limits based on a 99.5% test result interval, delta check criteria were broadened, and new specimen consistency rules were implemented. Decision guidance tools were also developed to assist staff using the AV system. The mean proportion of tests and samples autoverified improved from <62% for samples and <80% for tests, to >90% for samples and >95% for tests across all three sites. The new AV system significantly decreased turn-around time and total sample review time (to about a third), however, time spent for manual review of held samples almost tripled. There was no evidence of compromise to the quality of testing process and <1% of samples held for exceeding delta check or extreme limits required corrective action. The Six Sigma (DMAIC) process improvement methodology was successfully applied to AV systems resulting in an increase in overall test and sample AV by >90%, improved turn-around time, reduced time for manual verification, and with no obvious compromise to quality or error detection. Copyright © 2018 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Results for the Brine Evaporation Bag (BEB) Brine Processing Test

NASA Technical Reports Server (NTRS)

Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

2015-01-01

The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

Mapping Common Aphasia Assessments to Underlying Cognitive Processes and Their Neural Substrates.

PubMed

Lacey, Elizabeth H; Skipper-Kallal, Laura M; Xing, Shihui; Fama, Mackenzie E; Turkeltaub, Peter E

2017-05-01

Understanding the relationships between clinical tests, the processes they measure, and the brain networks underlying them, is critical in order for clinicians to move beyond aphasia syndrome classification toward specification of individual language process impairments. To understand the cognitive, language, and neuroanatomical factors underlying scores of commonly used aphasia tests. Twenty-five behavioral tests were administered to a group of 38 chronic left hemisphere stroke survivors and a high-resolution magnetic resonance image was obtained. Test scores were entered into a principal components analysis to extract the latent variables (factors) measured by the tests. Multivariate lesion-symptom mapping was used to localize lesions associated with the factor scores. The principal components analysis yielded 4 dissociable factors, which we labeled Word Finding/Fluency, Comprehension, Phonology/Working Memory Capacity, and Executive Function. While many tests loaded onto the factors in predictable ways, some relied heavily on factors not commonly associated with the tests. Lesion symptom mapping demonstrated discrete brain structures associated with each factor, including frontal, temporal, and parietal areas extending beyond the classical language network. Specific functions mapped onto brain anatomy largely in correspondence with modern neural models of language processing. An extensive clinical aphasia assessment identifies 4 independent language functions, relying on discrete parts of the left middle cerebral artery territory. A better understanding of the processes underlying cognitive tests and the link between lesion and behavior may lead to improved aphasia diagnosis, and may yield treatments better targeted to an individual's specific pattern of deficits and preserved abilities.

Processing of LEU targets for {sup 99}Mo production--testing and modification of the Cintichem process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, D.; Landsberger, S.; Buchholz, B.

1995-09-01

Recent experimental results on testing and modification of the Cintichem process to allow substitution of low enriched uranium (LEU) for high enriched uranium (HEU) targets are presented in this report. The main focus is on {sup 99}Mo recovery and purification by its precipitation with {alpha}-benzoin oxime. Parameters that were studied include concentrations of nitric and sulfuric acids, partial neutralization of the acids, molybdenum and uranium concentrations, and the ratio of {alpha}-benzoin oxime to molybdenum. Decontamination factors for uranium, neptunium, and various fission products were measured. Experiments with tracer levels of irradiated LEU were conducted for testing the {sup 99}Mo recoverymore » and purification during each step of the Cintichem process. Improving the process with additional processing steps was also attempted. The results indicate that the conversion of molybdenum chemical processing from HEU to LEU targets is possible.« less

Evidence of automatic processing in sequence learning using process-dissociation

PubMed Central

Mong, Heather M.; McCabe, David P.; Clegg, Benjamin A.

2012-01-01

This paper proposes a way to apply process-dissociation to sequence learning in addition and extension to the approach used by Destrebecqz and Cleeremans (2001). Participants were trained on two sequences separated from each other by a short break. Following training, participants self-reported their knowledge of the sequences. A recognition test was then performed which required discrimination of two trained sequences, either under the instructions to call any sequence encountered in the experiment “old” (the inclusion condition), or only sequence fragments from one half of the experiment “old” (the exclusion condition). The recognition test elicited automatic and controlled process estimates using the process dissociation procedure, and suggested both processes were involved. Examining the underlying processes supporting performance may provide more information on the fundamental aspects of the implicit and explicit constructs than has been attainable through awareness testing. PMID:22679465

Task Difficulty Differentially Affects Two Measures of Processing Load: The Pupil Response during Sentence Processing and Delayed Cued Recall of the Sentences

ERIC Educational Resources Information Center

Zekveld, Adriana A.; Festen, Joost M.; Kramer, Kramera

2013-01-01

Purpose: In this study, the authors assessed the influence of masking level (29% or 71% sentence perception) and test modality on the processing load during language perception as reflected by the pupil response. In addition, the authors administered a delayed cued stimulus recall test to examine whether processing load affected the encoding of…

Automated processing of endoscopic surgical instruments.

PubMed

Roth, K; Sieber, J P; Schrimm, H; Heeg, P; Buess, G

1994-10-01

This paper deals with the requirements for automated processing of endoscopic surgical instruments. After a brief analysis of the current problems, solutions are discussed. Test-procedures have been developed to validate the automated processing, so that the cleaning results are guaranteed and reproducable. Also a device for testing and cleaning was designed together with Netzsch Newamatic and PCI, called TC-MIC, to automate processing and reduce manual work.

A Hydrogen Containment Process for Nuclear Thermal Engine Ground testing

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Stewart, Eric; Canabal, Francisco

2016-01-01

The objective of this study is to propose a new total hydrogen containment process to enable the testing required for NTP engine development. This H2 removal process comprises of two unit operations: an oxygen-rich burner and a shell-and-tube type of heat exchanger. This new process is demonstrated by simulation of the steady state operation of the engine firing at nominal conditions.

Application of High Speed Digital Image Correlation in Rocket Engine Hot Fire Testing

NASA Technical Reports Server (NTRS)

Gradl, Paul R.; Schmidt, Tim

2016-01-01

Hot fire testing of rocket engine components and rocket engine systems is a critical aspect of the development process to understand performance, reliability and system interactions. Ground testing provides the opportunity for highly instrumented development testing to validate analytical model predictions and determine necessary design changes and process improvements. To properly obtain discrete measurements for model validation, instrumentation must survive in the highly dynamic and extreme temperature application of hot fire testing. Digital Image Correlation has been investigated and being evaluated as a technique to augment traditional instrumentation during component and engine testing providing further data for additional performance improvements and cost savings. The feasibility of digital image correlation techniques were demonstrated in subscale and full scale hotfire testing. This incorporated a pair of high speed cameras to measure three-dimensional, real-time displacements and strains installed and operated under the extreme environments present on the test stand. The development process, setup and calibrations, data collection, hotfire test data collection and post-test analysis and results are presented in this paper.

Proof test methodology for composites

NASA Technical Reports Server (NTRS)

Wu, Edward M.; Bell, David K.

1992-01-01

The special requirements for proof test of composites are identified based on the underlying failure process of composites. Two proof test methods are developed to eliminate the inevitable weak fiber sites without also causing flaw clustering which weakens the post-proof-test composite. Significant reliability enhancement by these proof test methods has been experimentally demonstrated for composite strength and composite life in tension. This basic proof test methodology is relevant to the certification and acceptance of critical composite structures. It can also be applied to the manufacturing process development to achieve zero-reject for very large composite structures.

Development of NASA's Sample Cartridge Assembly: Summary of GEDS Design, Development Testing, and Thermal Analyses

NASA Technical Reports Server (NTRS)

O'Connor, Brian; Hernandez, Deborah; Hornsby, Linda; Brown, Maria; Horton-Mullins, Kathryn

2017-01-01

Outline: Background of ISS (International Space Station) Material Science Research Rack; NASA SCA (Sample Cartridge Assembly) Design; GEDS (Gravitational Effects in Distortion in Sintering) Experiment Ampoule Design; Development Testing Summary; Thermal Modeling and Analysis. Summary: GEDS design development challenging (GEDS Ampoule design developed through MUGS (Microgravity) testing; Short duration transient sample processing; Unable to measure sample temperatures); MUGS Development testing used to gather data (Actual LGF (Low Gradient Furnace)-like furnace response; Provided sample for sintering evaluation); Transient thermal model integral to successful GEDS experiment (Development testing provided furnace response; PI (Performance Indicator) evaluation of sintering anchored model evaluation of processing durations; Thermal transient model used to determine flight SCA sample processing profiles).

Investigation of basic cognitive predictors of reading and spelling abilities in Tunisian third-grade primary school children.

PubMed

Batnini, Soulef; Uno, Akira

2015-06-01

This study investigated first the main cognitive abilities; phonological processing, visual cognition, automatization and receptive vocabulary in predicting reading and spelling abilities in Arabic. Second, we compared good/poor readers and spellers to detect the characteristics of cognitive predictors which contribute to identifying reading and spelling difficulties in Arabic speaking children. A sample of 116 Tunisian third-grade children was tested on their abilities to read and spell, phonological processing, visual cognition, automatization and receptive vocabulary. For reading, phonological processing and automatization uniquely predicted Arabic word reading and paragraph reading abilities. Automatization uniquely predicted Arabic non-word reading ability. For spelling, phonological processing was a unique predictor for Arabic word spelling ability. Furthermore, poor readers had significantly lower scores on the phonological processing test and slower reading times on the automatization test as compared with good readers. Additionally, poor spellers showed lower scores on the phonological processing test as compared with good spellers. Visual cognitive processing and receptive vocabulary were not significant cognitive predictors of Arabic reading and spelling abilities for Tunisian third grade children in this study. Our results are consistent with previous studies in alphabetic orthographies and demonstrate that phonological processing and automatization are the best cognitive predictors in detecting early literacy problems. We suggest including phonological processing and automatization tasks in screening tests and in intervention programs may help Tunisian children with poor literacy skills overcome reading and spelling difficulties in Arabic. Copyright © 2014 The Japanese Society of Child Neurology. Published by Elsevier B.V. All rights reserved.

Energy Systems Test Area (ESTA) Electrical Power Systems Test Operations: User Test Planning Guide

NASA Technical Reports Server (NTRS)

Salinas, Michael J.

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the ESTA Electrical Power Systems Test Laboratory. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Chamber B Thermal/Vacuum Chamber: User Test Planning Guide

NASA Technical Reports Server (NTRS)

Montz, Mike E.

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of Chamber B. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Audio Development Laboratory (ADL) User Test Planning Guide

NASA Technical Reports Server (NTRS)

Romero, Andy

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the ADL. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Advanced Materials Laboratory User Test Planning Guide

NASA Technical Reports Server (NTRS)

Orndoff, Evelyne

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the Advanced Materials Laboratory. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Developing Worksheet (LKS) Base on Process Skills in Curriculum 2013 at Elementary School Grade IV,V,VI

NASA Astrophysics Data System (ADS)

Subhan, M.; Oktolita, N.; Kn, M.

2018-04-01

The Lacks of students' skills in the learning process is due to lacks of exercises in the form of LKS. In the curriculum of 2013, there is no LKS as a companion to improve the students' skills. In order to solve those problem, it is necessary to develop LKS based on process skills as a teaching material to improve students' process skills. The purpose of this study is to develop LKS Process Skills based elementary school grade IV, V, VI which is integrated by process skill. The development of LKS can be used to develop the thematic process skills of elementary school students grade IV, V, VI based on curriculum 2013. The expected long-term goal is to produce teaching materials LKS Process Skill based of Thematic learning that is able to develop the process skill of elementary school students grade IV, V, VI. This development research refers to the steps developed by Borg & Gall (1983). The development process is carried out through 10 stages: preliminary research and gathering information, planning, draft development, initial test (limited trial), first product revision, final trial (field trial), product operational revision, Desemination and implementation. The limited subject of the this research is the students of SDN in Dharmasraya grade IV, V, VI. The field trial subjects in the experimental class are the students of SDN Dharmasraya grade IV, V, VI who have implemented the curriculum 2013. The data are collected by using LKS validation sheets, process skill observation sheets, and Thematic learning test (pre-test And post-test). The result of LKS development on the validity score is 81.70 (very valid), on practical score is 83.94 (very practical), and on effectiveness score is 86.67 (very effective). In the trial step the use of LKS using One Group Pretest-Posttest Design research design. The purpose of this trial is to know the effectiveness level of LKS result of development for improving the process skill of students in grade IV, V, and VI of elementary school. The data collection in this research uses the test result sheet of the process skill through pre-test and post-test. Observation results were analyzed with SPSS 16.0 software. The Result of analysis learning process of student skill of Sig value. (2-tailed) (0,000) <α (0.005) then H0 is rejected. There is a significant difference to the development of process skills between students using LKS with students who do not use LKS. It can be concluded that LKS have accuracy, ease and can improve result learn on aspect of skill process of student of grade IV, V and VI elementary school.

Pretreatment Engineering Platform Phase 1 Final Test Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.

2009-12-23

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes.( ) Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing wasmore » conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.« less

Control of polysilicon on-film particulates with on-product measurements

NASA Astrophysics Data System (ADS)

Barker, Judith B.; Chain, Elizabeth E.; Plachecki, Vincent E.

1997-08-01

Historically, a number of in-line particle measurements have been performed on separate test wafers included with product wafers during polysilicon processes. By performing film thickness and particulate measurements directly on product wafers, instead, a number of benefits accrue: (1) reduced test wafer usage, (2) reduced test wafer storage requirements, (3) reduced need for equipment to reclaim test wafers, (4) reduced need for direct labor to reclaim test wafers, and (5) reduced engineering 'false alarms' due to incorrectly processed test wafers. Implementation of on-product measurements for the polysilicon diffusion process required a number of changes in both philosophy and methodology. We show the necessary steps to implementation of on-product particle measurements with concern for overall manufacturing efficiency and the need to maintain appropriate control. Particle results from the Tencor 7600 Surfscan are presented.

The influence of retrieval practice on memory and comprehension of science texts

NASA Astrophysics Data System (ADS)

Hinze, Scott R.

The testing effect, where retrieval practice aids performance on later tests, may be a powerful tool for improving learning and retention. Three experiments test the potentials and limitations of retrieval practice for retention and comprehension of the content of science texts. Experiment 1 demonstrated that cued recall of paragraphs, but not fill-in-the-blank tests, improved performance on new memory items. Experiment 2 manipulated test expectancy and extended cued recall benefits to inference items. Test expectancies established prior to retrieval altered processing to either be ineffective (when expecting a memory test) or effective (when expecting an inference test). In Experiment 3, the processing task engaged in during retrieval practice was manipulated. Explanation during retrieval practice led to more effective transfer than free recall instructions, especially when participants were compliant and effective in their explanations. These experiments demonstrate that some, but not all, processing during retrieval practice can influence both memory and understanding of science texts.

Process Improvements in Training Device Acceptance Testing: A Study in Total Quality Management

DTIC Science & Technology

1990-12-12

Quality Management , a small group of Government and industry specialists examined the existing training device acceptance test process for potential improvements. The agreed-to mission of the Air Force/Industry partnership was to continuously identify and promote implementable approaches to minimize the cost and time required for acceptance testing while ensuring that validated performance supports the user training requirements. Application of a Total Quality process improvement model focused on the customers and their requirements, analyzed how work was accomplished, and

New cleaning technologies advance coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onursal, B.

1984-05-01

Alternative options are discussed for reducing sulfur dioxide emissions from coal burning utility and industrial sources. Test results indicate that it may be most advantageous to use the AED Process after coal preparation or on coals that do not need much ash removal. However, the developer claims that research efforts after 1981 have led to process improvements for producing clean coals containing 1.5% to 3% ash. This paper describes the test facility where a full-scale test of the AED Process is underway.

A Methodology and Software Environment for Testing Process Model’s Sequential Predictions with Protocols

DTIC Science & Technology

1992-12-21

in preparation). Foundations of artificial intelligence. Cambridge, MA: MIT Press. O’Reilly, R. C. (1991). X3DNet: An X- Based Neural Network ...2.2.3 Trace based protocol analysis 19 2.2A Summary of important data features 21 2.3 Tools related to process model testing 23 2.3.1 Tools for building...algorithm 57 3. Requirements for testing process models using trace based protocol 59 analysis 3.1 Definition of trace based protocol analysis (TBPA) 59

Dimensional processing of composite materials by picosecond pulsed ytterbium fiber laser

NASA Astrophysics Data System (ADS)

Kotov, S. A.

2017-12-01

In this paper, an experimental study of laser dimensional processing of thermoset carbon fiber reinforced plastics with a thickness of 2 and 3 mm was performed. In the process of work test rig setup based on picosecond pulsed fiber laser with 1.06 microns wavelength and 30 W average power was developed. Experimental tests were carried out at the maximum average power, with laser beam moved by a galvanometric mirrors system. Cutting tests were executed with different scanning velocity, using different laser modes, number of repetitions, hatching distance and focal plane position without process gas. As a result of the research recommendations for the selection processing mode parameters, providing minimal heat affected zone, good kerf geometry and high cutting speed were produced.

Engine Research Building’s Central Control Room

NASA Image and Video Library

1948-07-21

Operators in the Engine Research Building’s Central Control Room at the National Advisory Committee for Aeronautics (NACA) Lewis Flight Propulsion Laboratory. The massive 4.25-acre Engine Research Building contains dozens of test cells, test stands, and altitude chambers. A powerful collection of compressors and exhausters located in the central portion of the basement provided process air and exhaust for these test areas. This system is connected to similar process air systems in the laboratory’s other large test facilities. The Central Control Room coordinates this activity and communicates with the local utilities. This photograph was taken just after a major upgrade to the control room in 1948. The panels on the wall contain rudimentary floor plans of the different Engine Research Building sections with indicator lights and instrumentation for each test cell. The process air equipment included 12 exhausters, four compressors, a refrigeration system, cooling water, and an exhaust system. The operators in the control room kept in contact with engineers running the process air system and those conducting the tests in the test cells. The operators also coordinated with the local power companies to make sure enough electricity was available to operate the powerful compressors and exhausters.

Low-cost single-crystal turbine blades, volume 2

NASA Technical Reports Server (NTRS)

Strangman, T. E.; Dennis, R. E.; Heath, B. R.

1984-01-01

The overall objectives of Project 3 were to develop the exothermic casting process to produce uncooled single-crystal (SC) HP turbine blades in MAR-M 247 and higher strength derivative alloys and to validate the materials process and components through extensive mechanical property testing, rig testing, and 200 hours of endurance engine testing. These Program objectives were achieved. The exothermic casting process was successfully developed into a low-cost nonproperietary method for producing single-crystal castings. Single-crystal MAR-M 247 and two derivatives DS alloys developed during this project, NASAIR 100 and SC Alloy 3, were fully characterized through mechanical property testing. SC MAR-M 247 shows no significant improvement in strength over directionally solidified (DS) MAR-M 247, but the derivative alloys, NASAIR 100 and Alloy 3, show significant tensile and fatigue improvements. Firtree testing, holography, and strain-gauge rig testing were used to determine the effects of the anisotropic characteristics of single-crystal materials. No undesirable characteristics were found. In general, the single-crystal material behaved similarly to DS MAR-M 247. Two complete engine sets of SC HP turbine blades were cast using the exothermic casting process and fully machined. These blades were successfully engine-tested.

Identification of the Thickness of Nugget on Worksheet Spot Welding Using Non Destructive Test (NDT) - Effect of Pressure

NASA Astrophysics Data System (ADS)

Sifa, A.; Baskoro, A. S.; Sugeng, S.; Badruzzaman, B.; Endramawan, T.

2018-02-01

Resistance Spot Welding (RSW) is a process of connecting between two worksheet with thermomechanical loading process, RSW is widely used in automotive industry, the quality of splicing spot welding is influenced by several factors. One of the factors at the time of the welding process is pressure. The quality of welding on the nuggets can be determined by undertaking non-destructive testing by using Non Destructive Test (NDT) - Ultrasonic Test. In the NDT test is done by detecting the thickness of the nugget area, the purpose of research conducted to determine the effect of pressure to welding quality with Nugget thickness gauge measurement with Non Destructive Test method and manual measurement with micrometer, Experimental welding process by entering the welding parameters that have been specified and pressure variables 1 -5 bars on the worksheet thickness of 1 mm. The results of testing with NDT show there is addition of thickness in nugget superiority after compare with measurement result of thickness of nugget with micrometer which slightly experience thickness in nugget area, this indicates that the welding results have a connection between worksheet 1 and worksheet 2.

Laminated thermoplastic composite material from recycled high density polyethylene

NASA Technical Reports Server (NTRS)

Liu, Ping; Waskom, Tommy L.

1994-01-01

The design of a materials-science, educational experiment is presented. The student should understand the fundamentals of polymer processing and mechanical property testing of materials. The ability to use American Society for Testing and Materials (ASTM) standards is also necessary for designing material test specimens and testing procedures. The objectives of the experiment are (1) to understand the concept of laminated composite materials, processing, testing, and quality assurance of thermoplastic composites and (2) to observe an application example of recycled plastics.

Vibration and Acoustic Test Facility (VATF): User Test Planning Guide

NASA Technical Reports Server (NTRS)

Fantasia, Peter M.

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the VATF. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Six-Degree-of-Freedom Dynamic Test System (SDTS) User Test Planning Guide

NASA Technical Reports Server (NTRS)

Stokes, LeBarian

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the SDTS. The User Test Planning Guide aids in establishing expectations for both NASA and non- NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Goal Based Testing: A Risk Informed Process

NASA Technical Reports Server (NTRS)

Everline, Chester; Smith, Clayton; Distefano, Sal; Goldin, Natalie

2014-01-01

A process for life demonstration testing is developed, which can reduce the number of resources required by conventional sampling theory while still maintaining the same degree of rigor and confidence level. This process incorporates state-of-the-art probabilistic thinking and is consistent with existing NASA guidance documentation. This view of life testing changes the paradigm of testing a system for many hours to show confidence that a system will last for the required number of years to one that focuses efforts and resources on exploring how the system can fail at end-of-life and building confidence that the failure mechanisms are understood and well mitigated.

Evaluation of anomalies observed on film from S-190A flight system calibration test

NASA Technical Reports Server (NTRS)

Bourque, P. F.; Perry, L.; Sauer, G. E.

1975-01-01

Due to a persistent problem of scratched film from testing of the Skylab S-190A system, a series of tests were designed to identify the cause of the film scratching. The procedures followed in this test for pretest handling and packaging of the film, the makeup of the rolls for processing, and the results of the processed film evaluation are reported.

Feasibility Study of Cyclic Pressure Testing Thick-Walled Cylinders

DTIC Science & Technology

1975-01-01

Watervliet, and also • for tests on Navy barrela, is the hydrostatic pressure cycling test. This test employs a cloae-fitting, high -strength steel...mandrel to keep water volume at a minimum. High preaaure pumps then cycle the water up to the desired teat pres- • sure, thirty to fifty thousand...be accomplished using s high energy metalworking process - electrohydraulice. m • Electrohydraulica is a metalworking process which employs the

Adding Users to the Website Design Process

ERIC Educational Resources Information Center

Tomeo, Megan L.

2012-01-01

Alden Library began redesigning its website over a year ago. Throughout the redesign process the students, faculty, and staff that make up the user base were added to the conversation by utilizing several usability test methods. This article focuses on the usability testing conducted at Alden Library and delves into future usability testing, which…

Correlation of Selected Cognitive Abilities and Cognitive Processing Parameters: An Exploratory Study.

ERIC Educational Resources Information Center

Snow, Richard E.; And Others

This pilot study investigated some relationships between tested ability variables and processing parameters obtained from memory search and visual search tasks. The 25 undergraduates who participated had also participated in a previous investigation by Chiang and Atkinson. A battery of traditional ability tests and several film tests were…

Test results for SEU and SEL immune memory circuits

NASA Technical Reports Server (NTRS)

Wiseman, D.; Canaris, J.; Whitaker, S.; Gambles, J.; Arave, K.; Arave, L.

1993-01-01

Test results for three SEU logic/circuit hardened CMOS memory circuits verify upset and latch-up immunity for two configurations to be in excess of 120 MeV cm(exp 2)/mg using a commercial, non-radiation hardened CMOS process. Test chips from three separate fabrication runs in two different process were evaluated.

Investigating Test-Taking Behaviors Using Timing and Process Data

ERIC Educational Resources Information Center

Lee, Yi-Hsuan; Haberman, Shelby J.

2016-01-01

The use of computer-based assessments makes the collection of detailed data that capture examinees' progress in the tests and time spent on individual actions possible. This article presents a study using process and timing data to aid understanding of an international language assessment and the examinees. Issues regarding test-taking strategies,…

Levels of Conformity to Islamic Values and the Process of Identification.

ERIC Educational Resources Information Center

Nassir, Balkis

This study was conducted to measure the conformity levels and the identification process among university women students in an Islamic culture. Identity/conformity tests and costume identity tests were administered to 129 undergraduate female students at King Abdulaziz University in Saudi Arabia. The Photographic Costume Identity Test and the…

Comparison of infrared and 3D digital image correlation techniques applied for mechanical testing of materials

NASA Astrophysics Data System (ADS)

Krstulović-Opara, Lovre; Surjak, Martin; Vesenjak, Matej; Tonković, Zdenko; Kodvanj, Janoš; Domazet, Željko

2015-11-01

To investigate the applicability of infrared thermography as a tool for acquiring dynamic yielding in metals, a comparison of infrared thermography with three dimensional digital image correlation has been made. Dynamical tension tests and three point bending tests of aluminum alloys have been performed to evaluate results obtained by IR thermography in order to detect capabilities and limits for these two methods. Both approaches detect pastification zone migrations during the yielding process. The results of the tension test and three point bending test proved the validity of the IR approach as a method for evaluating the dynamic yielding process when used on complex structures such as cellular porous materials. The stability of the yielding process in the three point bending test, as contrary to the fluctuation of the plastification front in the tension test, is of great importance for the validation of numerical constitutive models. The research proved strong performance, robustness and reliability of the IR approach when used to evaluate yielding during dynamic loading processes, while the 3D DIC method proved to be superior in the low velocity loading regimes. This research based on two basic tests, proved the conclusions and suggestions presented in our previous research on porous materials where middle wave infrared thermography was applied.

Assessing Auditory Processing Abilities in Typically Developing School-Aged Children.

PubMed

McDermott, Erin E; Smart, Jennifer L; Boiano, Julie A; Bragg, Lisa E; Colon, Tiffany N; Hanson, Elizabeth M; Emanuel, Diana C; Kelly, Andrea S

2016-02-01

Large discrepancies exist in the literature regarding definition, diagnostic criteria, and appropriate assessment for auditory processing disorder (APD). Therefore, a battery of tests with normative data is needed. The purpose of this study is to collect normative data on a variety of tests for APD on children aged 7-12 yr, and to examine effects of outside factors on test performance. Children aged 7-12 yr with normal hearing, speech and language abilities, cognition, and attention were recruited for participation in this normative data collection. One hundred and forty-seven children were recruited using flyers and word of mouth. Of the participants recruited, 137 children qualified for the study. Participants attended schools located in areas that varied in terms of socioeconomic status, and resided in six different states. Audiological testing included a hearing screening (15 dB HL from 250 to 8000 Hz), word recognition testing, tympanometry, ipsilateral and contralateral reflexes, and transient-evoked otoacoustic emissions. The language, nonverbal IQ, phonological processing, and attention skills of each participant were screened using the Clinical Evaluation of Language Fundamentals-4 Screener, Test of Nonverbal Intelligence, Comprehensive Test of Phonological Processing, and Integrated Visual and Auditory-Continuous Performance Test, respectively. The behavioral APD battery included the following tests: Dichotic Digits Test, Frequency Pattern Test, Duration Pattern Test, Random Gap Detection Test, Compressed and Reverberated Words Test, Auditory Figure Ground (signal-to-noise ratio of +8 and +0), and Listening in Spatialized Noise-Sentences Test. Mean scores and standard deviations of each test were calculated, and analysis of variance tests were used to determine effects of factors such as gender, handedness, and birth history on each test. Normative data tables for the test battery were created for the following age groups: 7- and 8-yr-olds (n = 49), 9- and 10-yr-olds (n = 40), and 11- and 12-yr-olds (n = 48). No significant effects were seen for gender or handedness on any of the measures. The data collected in this study are appropriate for use in clinical diagnosis of APD. Use of a low-linguistically loaded core battery with the addition of more language-based tests, when language abilities are known, can provide a well-rounded picture of a child's auditory processing abilities. Screening for language, phonological processing, attention, and cognitive level can provide more information regarding a diagnosis of APD, determine appropriateness of the test battery for the individual child, and may assist with making recommendations or referrals. It is important to use a multidisciplinary approach in the diagnosis and treatment of APD due to the high likelihood of comorbidity with other language, learning, or attention deficits. Although children with other diagnoses may be tested for APD, it is important to establish previously made diagnoses before testing to aid in appropriate test selection and recommendations. American Academy of Audiology.

The use of applied software for the professional training of students studying humanities

NASA Astrophysics Data System (ADS)

Sadchikova, A. S.; Rodin, M. M.

2017-01-01

Research practice is an integral part of humanities students' training process. In this regard the training process is to include modern information techniques of the training process of students studying humanities. This paper examines the most popular applied software products used for data processing in social science. For testing purposes we selected the most commonly preferred professional packages: MS Excel, IBM SPSS Statistics, STATISTICA, STADIA. Moreover the article contains testing results of a specialized software Prikladnoy Sotsiolog that is applicable for the preparation stage of the research. The specialised software were tested during one term in groups of students studying humanities.

Developing Mathematical Processes (DMP). Field Test Evaluation, 1972-1973.

ERIC Educational Resources Information Center

Schall, William E.; And Others

The field test of the Developing Mathematical Processes (DMP) program was conducted jointly by the Falconer Central School, St. Mary's Elementary School in Dunkirk, New York, and the Teacher Education Research Center at the State University College in Fredonia, New York. DMP is a research-based, innovative, process-oriented elementary mathematics…

Benchmark Lisp And Ada Programs

NASA Technical Reports Server (NTRS)

Davis, Gloria; Galant, David; Lim, Raymond; Stutz, John; Gibson, J.; Raghavan, B.; Cheesema, P.; Taylor, W.

1992-01-01

Suite of nonparallel benchmark programs, ELAPSE, designed for three tests: comparing efficiency of computer processing via Lisp vs. Ada; comparing efficiencies of several computers processing via Lisp; or comparing several computers processing via Ada. Tests efficiency which computer executes routines in each language. Available for computer equipped with validated Ada compiler and/or Common Lisp system.

Why does selective attention to parts fail in face processing?

PubMed

Richler, Jennifer J; Tanaka, James W; Brown, Danielle D; Gauthier, Isabel

2008-11-01

One hallmark of holistic face processing is an inability to selectively attend to 1 face part while ignoring information in another part. In 3 sequential matching experiments, the authors tested perceptual and decisional accounts of holistic processing by measuring congruency effects between cued and uncued composite face halves shown in spatially aligned or disjointed configurations. The authors found congruency effects when the top and bottom halves of the study face were spatially aligned, misaligned (Experiment 1), or adjacent to one another (Experiment 2). However, at test, congruency effects were reduced by misalignment and abolished for adjacent configurations. This suggests that manipulations at test are more influential than manipulations at study, consistent with a decisional account of holistic processing. When encoding demands for study and test faces were equated (Experiment 3), the authors observed effects of study configuration suggesting that, consistent with a perceptual explanation, encoding does influence the magnitude of holistic processing. Together, these results cannot be accounted for by current perceptual or decisional accounts of holistic processing and suggest the existence of an attention-dependent mechanism that can integrate spatially separated face parts.

Advanced in-duct sorbent injection for SO{sub 2} control. Topical report No. 2, Subtask 2.2: Design optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenhoover, W.A.; Stouffer, M.R.; Withum, J.A.

1994-12-01

The objective of this research project is to develop second-generation duct injection technology as a cost-effective SO{sub 2} control option for the 1990 Clean Air Act Amendments. Research is focused on the Advanced Coolside process, which has shown the potential for achieving the performance targets of 90% SO{sub 2} removal and 60% sorbent utilization. In Subtask 2.2, Design Optimization, process improvement was sought by optimizing sorbent recycle and by optimizing process equipment for reduced cost. The pilot plant recycle testing showed that 90% SO{sub 2} removal could be achieved at sorbent utilizations up to 75%. This testing also showed thatmore » the Advanced Coolside process has the potential to achieve very high removal efficiency (90 to greater than 99%). Two alternative contactor designs were developed, tested and optimized through pilot plant testing; the improved designs will reduce process costs significantly, while maintaining operability and performance essential to the process. Also, sorbent recycle handling equipment was optimized to reduce cost.« less

Sleep quality and communication aspects in children.

PubMed

de Castro Corrêa, Camila; José, Maria Renata; Andrade, Eduardo Carvalho; Feniman, Mariza Ribeiro; Fukushiro, Ana Paula; Berretin-Felix, Giédre; Maximino, Luciana Paula

2017-09-01

To correlate quality of life of children in terms of sleep, with their oral language skills, auditory processing and orofacial myofunctional aspects. Nineteen children (12 males and seven females, in the mean age 9.26) undergoing otorhinolaryngological and speech evaluations participated in this study. The OSA-18 questionnaire was applied, followed by verbal and nonverbal sequential memory tests, dichotic digit test, nonverbal dichotic test and Sustained Auditory Attention Ability Test, related to auditory processing. The Phonological Awareness Profile test, Rapid Automatized Naming and Phonological Working Memory were used for assessment of the phonological processing. Language was assessed by the ABFW Child Language Test, analyzing the phonological and lexical levels. Orofacial myofunctional aspects were evaluated through the MBGR Protocol. Statistical tests used: the Mann-Whitney Test, Fisher's exact test and Spearman Correlation. Relating the performance of children in all evaluations to the results obtained in the OSA-18, there was a statistically significant correlation in the phonological working memory for backward digits (p = 0.04); as well as in the breathing item (p = 0.03), posture of the mandible (p = 0.03) and mobility of lips (p = 0.04). A correlation was seen between the sleep quality of life and the skills related to the phonological processing, specifically in the phonological working memory in backward digits, and related to orofacial myofunctional aspects. Copyright © 2017 Elsevier B.V. All rights reserved.

Text Processing: The Role of Reader Expectations and Background Knowledge.

DTIC Science & Technology

1987-08-01

essay test were expected, but spend more time processing lower-- level information than if a recognition test were expected. Furthermore, processing ...shifts ii tle amount of time devoted to reading information at various levels in a t.x, structure, rather than dramatic differences in processing patt...structures ( Craik & Lockhart , 1972; Goetz, Schallert, Reynolds, & Radin, 1983). If new information is compatible with existing memory structures, it is

PROCESS WATER BUILDING, TRA605. CONTEXTUAL VIEW, CAMERA FACING SOUTHEAST. PROCESS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PROCESS WATER BUILDING, TRA-605. CONTEXTUAL VIEW, CAMERA FACING SOUTHEAST. PROCESS WATER BUILDING AND ETR STACK ARE IN LEFT HALF OF VIEW. TRA-666 IS NEAR CENTER, ABUTTED BY SECURITY BUILDING; TRA-626, AT RIGHT EDGE OF VIEW BEHIND BUS. INL NEGATIVE NO. HD46-34-1. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Theoretical test of Jarzynski's equality for reversible volume-switching processes of an ideal gas system.

PubMed

Sung, Jaeyoung

2007-07-01

We present an exact theoretical test of Jarzynski's equality (JE) for reversible volume-switching processes of an ideal gas system. The exact analysis shows that the prediction of JE for the free energy difference is the same as the work done on the gas system during the reversible process that is dependent on the shape of path of the reversible volume-switching process.

Speed of processing and strategic control of attention after traumatic brain injury.

PubMed

Dymowski, Alicia Rhian; Owens, Jacqueline Anne; Ponsford, Jennie Louise; Willmott, Catherine

2015-01-01

Slowed information processing speed has consistently been documented after traumatic brain injury (TBI). Debate continues as to whether deficits in strategic control are proportionate to, or remain after controlling for, reduced speed of processing. The study aim was to investigate the association of speed of processing and strategic control of attention with working memory, selective attention, response inhibition, and mental flexibility task performance after TBI using traditional and novel clinical measures. Twenty-five individuals with complicated mild to severe TBI (post-traumatic amnesia duration, M = 39.52 days, SD = 38.34; worst Glasgow Coma Scale score, M = 7.33, SD = 4.35; time post-injury, M = 392.64 days, SD = 537.19) and 25 matched healthy controls completed assessment of attentional and executive functioning. Measures included the Symbol Digit Modalities Test (SDMT), the computerized Selective Attention Task (SAT), the Ruff 2&7 Selective Attention Test (2&7), the visual n-back, Digit Span, Hayling Test, and Trail Making Test (TMT). t tests revealed that individuals with TBI demonstrated reduced processing speed on the SDMT, n-back, SAT, 2&7, Hayling Test, and TMT-A (p ≤ .002 for all). Digit Span performance did not differ between groups. Mixed-model ANOVAs revealed that individuals with TBI demonstrated a disproportionate increase in reaction time with complexity, which was accounted for by speed on the SAT but remained on the Hayling Inhibition Test after controlling for speed in ANCOVAs. Mann-Whitney U tests revealed that individuals with TBI also made more errors on the Hayling Test, missed responses on the n-back and were unable to benefit from the automatic condition of the 2&7. While slowed speed of information processing was pervasive across tasks after TBI, residual difficulties in response inhibition remained after controlling for slowness, which suggests impaired strategic control. These findings support targeted intervention for slowed speed of thinking and inhibition following TBI.

J-2X Test Articles Using FDM Process

NASA Technical Reports Server (NTRS)

Anderson, Ted; Ruf, Joe; Steele, Phil

2010-01-01

This viewgraph presentation gives a brief history of the J-2X engine, along with detailed description of the material demonstrator and test articles that were created using Fused Deposition Modeling (FDM) process.

The broader cognitive phenotype of autism in parents: how specific is the tendency for local processing and executive dysfunction?

PubMed

Bölte, Sven; Poustka, Fritz

2006-06-01

The objective of this study was to investigate the tendency for local processing style ('weak central coherence') and executive dysfunction in parents of subjects with an autism spectrum disorder (ASD) compared with parents of individuals with early onset schizophrenia (EOS) and mental retardation (MR). Sixty-two parents of subjects with ASD, 36 parents of subjects with EOS and 30 parents of subjects with MR were examined. Data on two scales indicative of local visual processing (Embedded Figures Test, Block Design) and on three executive function tests (Wisconsin Card Sorting Test, Tower of Hanoi, Trailmaking Test) were collected for all participants. Parents of subjects with ASD performed significantly faster on the Embedded Figures Test compared with both control samples. No other substantial group differences were observed. The findings indicate that an increased tendency for local processing in terms of visual disembedding could be a relatively specific core feature of the broader cognitive phenotype of autism in parents.

The opto-mechanical design process: from vision to reality

NASA Astrophysics Data System (ADS)

Kvamme, E. Todd; Stubbs, David M.; Jacoby, Michael S.

2017-08-01

The design process for an opto-mechanical sub-system is discussed from requirements development through test. The process begins with a proper mission understanding and the development of requirements for the system. Preliminary design activities are then discussed with iterative analysis and design work being shared between the design, thermal, and structural engineering personnel. Readiness for preliminary review and the path to a final design review are considered. The value of prototyping and risk mitigation testing is examined with a focus on when it makes sense to execute a prototype test program. System level margin is discussed in general terms, and the practice of trading margin in one area of performance to meet another area is reviewed. Requirements verification and validation is briefly considered. Testing and its relationship to requirements verification concludes the design process.

Executive functioning and processing speed in age-related differences in memory: contribution of a coding task.

PubMed

Baudouin, Alexia; Clarys, David; Vanneste, Sandrine; Isingrini, Michel

2009-12-01

The aim of the present study was to examine executive dysfunctioning and decreased processing speed as potential mediators of age-related differences in episodic memory. We compared the performances of young and elderly adults in a free-recall task. Participants were also given tests to measure executive functions and perceptual processing speed and a coding task (the Digit Symbol Substitution Test, DSST). More precisely, we tested the hypothesis that executive functions would mediate the age-related differences observed in the free-recall task better than perceptual speed. We also tested the assumption that a coding task, assumed to involve both executive processes and perceptual speed, would be the best mediator of age-related differences in memory. Findings first confirmed that the DSST combines executive processes and perceptual speed. Secondly, they showed that executive functions are a significant mediator of age-related differences in memory, and that DSST performance is the best predictor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vorres, K S

The overall accomplishments of the HYGAS program to date are that it has demonstrated the key process concepts and integrated unit operations of coal gasification. It has also demonstrated several methods of hydrogen generation, including catalytic steam reforming of natural gas, electrothermal gasification, and also steam-oxygen gasification. A total of 37 tests with lignite, including a total of 5500 tons of lignite processed, demonstrated the technical feasibility of a gasification process using lignite. A total of 17 tests with bituminous coal involved a total of 3100 tons. Some specific objectives of the HYGAS program for fiscal 1977 include tests tomore » be conducted with subbituminous coal. Data will be collected for use in the design of an effluent treatment and water reuse cycles in a commercial plant. New methanation catalysts will be tested. Materials testing will continue.« less

Nondestructive examination of recovery stage during annealing of a cold-rolled low-carbon steel using eddy current testing technique

NASA Astrophysics Data System (ADS)

Seyfpour, M.; Ghanei, S.; Mazinani, M.; Kashefi, M.; Davis, C.

2018-04-01

The recovery process in steel is usually investigated by conventional destructive tests that are expensive, time-consuming and also cumbersome. In this study, an alternative non-destructive test technique (based on eddy current testing) is used to characterise the recovery process during annealing of cold-rolled low-carbon steels. For assessing the reliability of eddy current results corresponding to different levels of recovery, X-ray line broadening analysis is also employed. It is shown that there is a strong relationship between eddy current outputs and the extent to which recovery occurs at different annealing temperatures. Accordingly, the non-destructive eddy current test technique represents the potential to be used as a reliable process for detection of the occurrence of recovery in the steel microstructure.

Development of the GPM Observatory Thermal Vacuum Test Model

NASA Technical Reports Server (NTRS)

Yang, Kan; Peabody, Hume

2012-01-01

A software-based thermal modeling process was documented for generating the thermal panel settings necessary to simulate worst-case on-orbit flight environments in an observatory-level thermal vacuum test setup. The method for creating such a thermal model involved four major steps: (1) determining the major thermal zones for test as indicated by the major dissipating components on the spacecraft, then mapping the major heat flows between these components; (2) finding the flight equivalent sink temperatures for these test thermal zones; (3) determining the thermal test ground support equipment (GSE) design and initial thermal panel settings based on the equivalent sink temperatures; and (4) adjusting the panel settings in the test model to match heat flows and temperatures with the flight model. The observatory test thermal model developed from this process allows quick predictions of the performance of the thermal vacuum test design. In this work, the method described above was applied to the Global Precipitation Measurement (GPM) core observatory spacecraft, a joint project between NASA and the Japanese Aerospace Exploration Agency (JAXA) which is currently being integrated at NASA Goddard Space Flight Center for launch in Early 2014. From preliminary results, the thermal test model generated from this process shows that the heat flows and temperatures match fairly well with the flight thermal model, indicating that the test model can simulate fairly accurately the conditions on-orbit. However, further analysis is needed to determine the best test configuration possible to validate the GPM thermal design before the start of environmental testing later this year. Also, while this analysis method has been applied solely to GPM, it should be emphasized that the same process can be applied to any mission to develop an effective test setup and panel settings which accurately simulate on-orbit thermal environments.

A 'Turing' Test for Landscape Evolution Models

NASA Astrophysics Data System (ADS)

Parsons, A. J.; Wise, S. M.; Wainwright, J.; Swift, D. A.

2008-12-01

Resolving the interactions among tectonics, climate and surface processes at long timescales has benefited from the development of computer models of landscape evolution. However, testing these Landscape Evolution Models (LEMs) has been piecemeal and partial. We argue that a more systematic approach is required. What is needed is a test that will establish how 'realistic' an LEM is and thus the extent to which its predictions may be trusted. We propose a test based upon the Turing Test of artificial intelligence as a way forward. In 1950 Alan Turing posed the question of whether a machine could think. Rather than attempt to address the question directly he proposed a test in which an interrogator asked questions of a person and a machine, with no means of telling which was which. If the machine's answer could not be distinguished from those of the human, the machine could be said to demonstrate artificial intelligence. By analogy, if an LEM cannot be distinguished from a real landscape it can be deemed to be realistic. The Turing test of intelligence is a test of the way in which a computer behaves. The analogy in the case of an LEM is that it should show realistic behaviour in terms of form and process, both at a given moment in time (punctual) and in the way both form and process evolve over time (dynamic). For some of these behaviours, tests already exist. For example there are numerous morphometric tests of punctual form and measurements of punctual process. The test discussed in this paper provides new ways of assessing dynamic behaviour of an LEM over realistically long timescales. However challenges remain in developing an appropriate suite of challenging tests, in applying these tests to current LEMs and in developing LEMs that pass them.

The General Mission Analysis Tool (GMAT) System Test Plan

NASA Technical Reports Server (NTRS)

Conway, Darrel J.; Hughes, Steven P.

2007-01-01

This document serves as the System Test Approach for the GMAT Project. Preparation for system testing consists of three major stages: 1) The Test Approach sets the scope of system testing, the overall strategy to be adopted, the activities to be completed, the general resources required and the methods and processes to be used to test the release. It also details the activities, dependencies and effort required to conduct the System Test. 2) Test Planning details the activities, dependencies and effort required to conduct the System Test. 3) Test Cases documents the tests to be applied, the data to be processed, the automated testing coverage and the expected results. This document covers the first two of these items, and established the framework used for the GMAT test case development. The test cases themselves exist as separate components, and are managed outside of and concurrently with this System Test Plan.

Mapping common aphasia assessments to underlying cognitive processes and their neural substrates

PubMed Central

Lacey, Elizabeth H.; Skipper-Kallal, LM; Xing, S; Fama, ME; Turkeltaub, PE

2017-01-01

Background Understanding the relationships between clinical tests, the processes they measure, and the brain networks underlying them, is critical in order for clinicians to move beyond aphasia syndrome classification toward specification of individual language process impairments. Objective To understand the cognitive, language, and neuroanatomical factors underlying scores of commonly used aphasia tests. Methods 25 behavioral tests were administered to a group of 38 chronic left hemisphere stroke survivors and a high resolution MRI was obtained. Test scores were entered into a principal components analysis to extract the latent variables (factors) measured by the tests. Multivariate lesion-symptom mapping was used to localize lesions associated with the factor scores. Results The principal components analysis yielded four dissociable factors, which we labeled Word Finding/Fluency, Comprehension, Phonology/Working Memory Capacity, and Executive Function. While many tests loaded onto the factors in predictable ways, some relied heavily on factors not commonly associated with the tests. Lesion symptom mapping demonstrated discrete brain structures associated with each factor, including frontal, temporal, and parietal areas extending beyond the classical language network. Specific functions mapped onto brain anatomy largely in correspondence with modern neural models of language processing. Conclusions An extensive clinical aphasia assessment identifies four independent language functions, relying on discrete parts of the left middle cerebral artery territory. A better understanding of the processes underlying cognitive tests and the link between lesion and behavior may lead to improved aphasia diagnosis, and may yield treatments better targeted to an individual’s specific pattern of deficits and preserved abilities. PMID:28135902

Development Instrument’s Learning of Physics Through Scientific Inquiry Model Based Batak Culture to Improve Science Process Skill and Student’s Curiosity

NASA Astrophysics Data System (ADS)

Nasution, Derlina; Syahreni Harahap, Putri; Harahap, Marabangun

2018-03-01

This research aims to: (1) developed a instrument’s learning (lesson plan, worksheet, student’s book, teacher’s guide book, and instrument test) of physics learning through scientific inquiry learning model based Batak culture to achieve skills improvement process of science students and the students’ curiosity; (2) describe the quality of the result of develop instrument’s learning in high school using scientific inquiry learning model based Batak culture (lesson plan, worksheet, student’s book, teacher’s guide book, and instrument test) to achieve the science process skill improvement of students and the student curiosity. This research is research development. This research developed a instrument’s learning of physics by using a development model that is adapted from the development model Thiagarajan, Semmel, and Semmel. The stages are traversed until retrieved a valid physics instrument’s learning, practical, and effective includes :(1) definition phase, (2) the planning phase, and (3) stages of development. Test performed include expert test/validation testing experts, small groups, and test classes is limited. Test classes are limited to do in SMAN 1 Padang Bolak alternating on a class X MIA. This research resulted in: 1) the learning of physics static fluid material specially for high school grade 10th consisted of (lesson plan, worksheet, student’s book, teacher’s guide book, and instrument test) and quality worthy of use in the learning process; 2) each component of the instrument’s learning meet the criteria have valid learning, practical, and effective way to reach the science process skill improvement and curiosity in students.

Atmospheric Reentry Materials and Structures Evaluation Facility (ARMSEF). User Test Planning Guide

NASA Technical Reports Server (NTRS)

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the ARMSEF. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

vvtools v. 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drake, Richard R.

Vvtools is a suite of testing tools, with a focus on reproducible verification and validation. They are written in pure Python, and contain a test harness and an automated process management tool. Users of vvtools can develop suites of verification and validation tests and run them on small to large high performance computing resources in an automated and reproducible way. The test harness enables complex processes to be performed in each test and even supports a one-level parent/child dependency between tests. It includes a built in capability to manage workloads requiring multiple processors and platforms that use batch queueing systems.

Testing and Feedback Effects on Front-End Control over Later Retrieval

ERIC Educational Resources Information Center

Thomas, Ruthann C.; McDaniel, Mark A.

2013-01-01

In 2 experiments, we explored differences in cognitive control at retrieval on a final test to better understand the mechanisms underlying the powerful boost in recall of previously tested information. Memory retrieval can be enhanced by front-end control processes that regulate the scope of retrieval or by later processes that monitor retrieval…

How to Reason with Economic Concepts: Cognitive Process of Japanese Undergraduate Students Solving Test Items

ERIC Educational Resources Information Center

Asano, Tadayoshi; Yamaoka, Michio

2015-01-01

The authors administered a Japanese version of the Test of Understanding in College Economics, the fourth edition (TUCE-4) to assess the economic literacy of Japanese undergraduate students in 2006 and 2009. These two test results were combined to investigate students' cognitive process or reasoning with specific economic concepts and principles…

49 CFR 40.61 - What are the preliminary steps in the collection process?

Code of Federal Regulations, 2010 CFR

2010-10-01

... that the alcohol test is completed before the urine collection process begins. Example to paragraph (b... ensure that post-accident and reasonable suspicion alcohol tests happen as soon as possible (e.g., by... actually beginning a collection: (a) When a specific time for an employee's test has been scheduled, or the...

49 CFR 40.61 - What are the preliminary steps in the collection process?

Code of Federal Regulations, 2011 CFR

2011-10-01

... that the alcohol test is completed before the urine collection process begins. Example to paragraph (b... ensure that post-accident and reasonable suspicion alcohol tests happen as soon as possible (e.g., by... actually beginning a collection: (a) When a specific time for an employee's test has been scheduled, or the...

49 CFR 40.61 - What are the preliminary steps in the collection process?

Code of Federal Regulations, 2013 CFR

2013-10-01

... that the alcohol test is completed before the urine collection process begins. Example to paragraph (b... ensure that post-accident and reasonable suspicion alcohol tests happen as soon as possible (e.g., by... actually beginning a collection: (a) When a specific time for an employee's test has been scheduled, or the...

49 CFR 40.61 - What are the preliminary steps in the collection process?

Code of Federal Regulations, 2014 CFR

2014-10-01

... that the alcohol test is completed before the urine collection process begins. Example to paragraph (b... ensure that post-accident and reasonable suspicion alcohol tests happen as soon as possible (e.g., by... actually beginning a collection: (a) When a specific time for an employee's test has been scheduled, or the...

49 CFR 40.61 - What are the preliminary steps in the collection process?

Code of Federal Regulations, 2012 CFR

2012-10-01

... that the alcohol test is completed before the urine collection process begins. Example to paragraph (b... ensure that post-accident and reasonable suspicion alcohol tests happen as soon as possible (e.g., by... actually beginning a collection: (a) When a specific time for an employee's test has been scheduled, or the...

Lab Procedures. Sludge Treatment and Disposal Course #166. Instructor's Guide [and] Student Workbook.

ERIC Educational Resources Information Center

Carnegie, John W.

Laboratory tests used to determine status and to evaluate and/or maintain process control of the various sludge treatment processes are introduced in this lesson. Neither detailed test procedures nor explanations of how the tests should be applied to every unit are explained; this information is provided in other modules. The instructor's manual…

Joint Test Report for Validation of Alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel

NASA Technical Reports Server (NTRS)

Lewis, Pattie

2007-01-01

Headquarters National Aeronautics and Space Administration (NASA) chartered the NASA Acquisition Pollution Prevention (AP2) Office to coordinate agency activities affecting pollution prevention issues identified during system and component acquisition and sustainment processes. The primary objectives of the AP2 Office are to: (1) Reduce or eliminate the use of hazardous materials or hazardous processes at manufacturing, remanufacturing, and sustainment locations. (2) Avoid duplication of effort in actions required to reduce or eliminate hazardous materials through joint center cooperation and technology sharing. The objective of this project was to qualify candidate alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel applications at NASA facilities. This project compares the surface preparation/depainting performance of the proposed alternatives to existing surface preparation/depainting systems or standards. This Joint Test Report (JTR) contains the results of testing as per the outlines of the Joint Test Protocol (JTP), Joint Test Protocol for Validation of Alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel, and the Field Test Plan (FTP), Field Evaluations Test Plan for Validation of Alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel, for critical requirements and tests necessary to qualify alternatives for coating removal systems. These tests were derived from engineering, performance, and operational impact (supportability) requirements defined by a consensus of government and industry participants. This JTR documents the results of the testing as well as any test modifications made during the execution of the project. This JTR is made available as a reference for future pollution prevention endeavors by other NASA Centers, the Department of Defense and commercial users to minimize duplication of effort. The current coating removal processes identified herein are for polyurethane, epoxy and other paint systems applied by conventional wet-spray processes. A table summarizes the target hazardous materials, processes and materials, applications, affected programs, and candidate substrates.

Interest and attention in facial recognition.

PubMed

Burgess, Melinda C R; Weaver, George E

2003-04-01

When applied to facial recognition, the levels of processing paradigm has yielded consistent results: faces processed in deep conditions are recognized better than faces processed under shallow conditions. However, there are multiple explanations for this occurrence. The own-race advantage in facial recognition, the tendency to recognize faces from one's own race better than faces from another race, is also consistently shown but not clearly explained. This study was designed to test the hypothesis that the levels of processing findings in facial recognition are a result of interest and attention, not differences in processing. This hypothesis was tested for both own and other faces with 105 Caucasian general psychology students. Levels of processing was manipulated as a between-subjects variable; students were asked to answer one of four types of study questions, e.g., "deep" or "shallow" processing questions, while viewing the study faces. Students' recognition of a subset of previously presented Caucasian and African-American faces from a test-set with an equal number of distractor faces was tested. They indicated their interest in and attention to the task. The typical levels of processing effect was observed with better recognition performance in the deep conditions than in the shallow conditions for both own- and other-race faces. The typical own-race advantage was also observed regardless of level of processing condition. For both own- and other-race faces, level of processing explained a significant portion of the recognition variance above and beyond what was explained by interest in and attention to the task.

Performance Testing of a Trace Contaminant Control Subassembly for the International Space Station

NASA Technical Reports Server (NTRS)

Perry, J. L.; Curtis, R. E.; Alexandre, K. L.; Ruggiero, L. L.; Shtessel, N.

1998-01-01

As part of the International Space Station (ISS) Trace Contaminant Control Subassembly (TCCS) development, a performance test has been conducted to provide reference data for flight verification analyses. This test, which used the U.S. Habitation Module (U.S. Hab) TCCS as the test article, was designed to add to the existing database on TCCS performance. Included in this database are results obtained during ISS development testing; testing of functionally similar TCCS prototype units; and bench scale testing of activated charcoal, oxidation catalyst, and granular lithium hydroxide (LiOH). The present database has served as the basis for the development and validation of a computerized TCCS process simulation model. This model serves as the primary means for verifying the ISS TCCS performance. In order to mitigate risk associated with this verification approach, the U.S. Hab TCCS performance test provides an additional set of data which serve to anchor both the process model and previously-obtained development test data to flight hardware performance. The following discussion provides relevant background followed by a summary of the test hardware, objectives, requirements, and facilities. Facility and test article performance during the test is summarized, test results are presented, and the TCCS's performance relative to past test experience is discussed. Performance predictions made with the TCCS process model are compared with the U.S. Hab TCCS test results to demonstrate its validation.

Low visual information-processing speed and attention are predictors of fatigue in elementary and junior high school students

PubMed Central

2011-01-01

Background Fatigue is a common complaint among elementary and junior high school students, and is known to be associated with reduced academic performance. Recently, we demonstrated that fatigue was correlated with decreased cognitive function in these students. However, no studies have identified cognitive predictors of fatigue. Therefore, we attempted to determine independent cognitive predictors of fatigue in these students. Methods We performed a prospective cohort study. One hundred and forty-two elementary and junior high school students without fatigue participated. They completed a variety of paper-and-pencil tests, including list learning and list recall tests, kana pick-out test, semantic fluency test, figure copying test, digit span forward test, and symbol digit modalities test. The participants also completed computerized cognitive tests (tasks A to E on the modified advanced trail making test). These cognitive tests were used to evaluate motor- and information-processing speed, immediate and delayed memory function, auditory and visual attention, divided and switching attention, retrieval of learned material, and spatial construction. One year after the tests, a questionnaire about fatigue (Japanese version of the Chalder Fatigue Scale) was administered to all the participants. Results After the follow-up period, we confirmed 40 cases of fatigue among 118 students. In multivariate logistic regression analyses adjusted for grades and gender, poorer performance on visual information-processing speed and attention tasks was associated with increased risk of fatigue. Conclusions Reduced visual information-processing speed and poor attention are independent predictors of fatigue in elementary and junior high school students. PMID:21672212

Low visual information-processing speed and attention are predictors of fatigue in elementary and junior high school students.

PubMed

Mizuno, Kei; Tanaka, Masaaki; Fukuda, Sanae; Yamano, Emi; Shigihara, Yoshihito; Imai-Matsumura, Kyoko; Watanabe, Yasuyoshi

2011-06-14

Fatigue is a common complaint among elementary and junior high school students, and is known to be associated with reduced academic performance. Recently, we demonstrated that fatigue was correlated with decreased cognitive function in these students. However, no studies have identified cognitive predictors of fatigue. Therefore, we attempted to determine independent cognitive predictors of fatigue in these students. We performed a prospective cohort study. One hundred and forty-two elementary and junior high school students without fatigue participated. They completed a variety of paper-and-pencil tests, including list learning and list recall tests, kana pick-out test, semantic fluency test, figure copying test, digit span forward test, and symbol digit modalities test. The participants also completed computerized cognitive tests (tasks A to E on the modified advanced trail making test). These cognitive tests were used to evaluate motor- and information-processing speed, immediate and delayed memory function, auditory and visual attention, divided and switching attention, retrieval of learned material, and spatial construction. One year after the tests, a questionnaire about fatigue (Japanese version of the Chalder Fatigue Scale) was administered to all the participants. After the follow-up period, we confirmed 40 cases of fatigue among 118 students. In multivariate logistic regression analyses adjusted for grades and gender, poorer performance on visual information-processing speed and attention tasks was associated with increased risk of fatigue. Reduced visual information-processing speed and poor attention are independent predictors of fatigue in elementary and junior high school students. © 2011 Mizuno et al; licensee BioMed Central Ltd.

Apollo-Soyuz test project photographic film processing and sensitometric summary

NASA Technical Reports Server (NTRS)

Lockwood, H. E.

1975-01-01

The Photographic Technology Division at the NASA Lyndon B. Johnson Space Center processed original photographic films exposed in flight during the Apollo Soyuz Test Project (ASTP). Integrated with processing of the original films were strict sensitometric controls and certification procedures established prior to the flight. Information relative to the processing of the 54 rolls of original ASTP flight film and sensitometric data pertinent to each of these rolls of film is presented.

Dimpled ball grid array process development for space flight applications

NASA Technical Reports Server (NTRS)

Barr, S. L.; Mehta, A.

2000-01-01

A 472 dimpled ball grid array (D-BGA) package has not been used in past space flight environments, therefore it was necessary to develop a process that would yield robust and reliable solder joints. The process developing assembly, inspection and rework techniques, were verified by conducting environmental tests. Since the 472 D-BGA packages passed the above environmental tests within the specifications, the process was successfully developed for space flight electronics.

Auditory processing disorders, verbal disfluency, and learning difficulties: a case study.

PubMed

Jutras, Benoît; Lagacé, Josée; Lavigne, Annik; Boissonneault, Andrée; Lavoie, Charlen

2007-01-01

This case study reports the findings of auditory behavioral and electrophysiological measures performed on a graduate student (identified as LN) presenting verbal disfluency and learning difficulties. Results of behavioral audiological testing documented the presence of auditory processing disorders, particularly temporal processing and binaural integration. Electrophysiological test results, including middle latency, late latency and cognitive potentials, revealed that LN's central auditory system processes acoustic stimuli differently to a reference group with normal hearing.

40 CFR 63.1312 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

....111) Owner or operator (§ 63.2) Performance evaluation (§ 63.2) Performance test (§ 63.2) Permitting...) Research and development facility (§ 63.101) Routed to a process or route to a process (§ 63.161) Run (§ 63... vessel (§ 63.161) Temperature monitoring device (§ 63.111) Test method (§ 63.2) Treatment process (§ 63...

Testing Signal-Detection Models of Yes/No and Two-Alternative Forced-Choice Recognition Memory

ERIC Educational Resources Information Center

Jang, Yoonhee; Wixted, John T.; Huber, David E.

2009-01-01

The current study compared 3 models of recognition memory in their ability to generalize across yes/no and 2-alternative forced-choice (2AFC) testing. The unequal-variance signal-detection model assumes a continuous memory strength process. The dual-process signal-detection model adds a thresholdlike recollection process to a continuous…

Transfer of Training and Processing Instruction: From Input to Output

ERIC Educational Resources Information Center

VanPatten, Bill; Uludag, Onur

2011-01-01

In this paper we report the findings of an experiment to test whether training via processing instruction transfers to output tasks. Two groups of Turkish L1-English L2 learners participated: one that received processing instruction on passive structures and a control group that did not receive any instruction on passives. A pre-test/multiple…

Qualification of submerged-arc narrow strip cladding process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayres, P.S.; Gottschling, J.D.; Jeffers, G.K.

1975-08-01

An unique narrow strip cladding process for use on both plate and forging material for nuclear components was developed. The qualification testing of this low-heat input process for cladding nuclear components, including those of SA508 Class 2 material is described. The theory that explains the acceptable results of these tests is also given. (auth)

Qualification of submerged-arc narrow strip cladding process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayres, P.S.; Gottschling, J.D.; Jeffers, G.K.

1976-03-01

Babcock and Wilcox has developed an unique narrow strip cladding process for use on both plate and forging material for nuclear components. The qualification testing of this low-heat input process for cladding nuclear components is described, including those of SA508 Class 2 material. The theory that explains the acceptable results of these tests is also given.

A General Audiovisual Temporal Processing Deficit in Adult Readers with Dyslexia

ERIC Educational Resources Information Center

Francisco, Ana A.; Jesse, Alexandra; Groen, Margriet A.; McQueen, James M.

2017-01-01

Purpose: Because reading is an audiovisual process, reading impairment may reflect an audiovisual processing deficit. The aim of the present study was to test the existence and scope of such a deficit in adult readers with dyslexia. Method: We tested 39 typical readers and 51 adult readers with dyslexia on their sensitivity to the simultaneity of…

Partially Testing a Process Model for Understanding Victim Responses to an Anticipated Worksite Closure

ERIC Educational Resources Information Center

Blau, Gary

2007-01-01

This study partially tested a recent process model for understanding victim responses to worksite/function closure (W/FC) proposed by Blau [Blau, G. (2006). A process model for understanding victim responses to worksite/function closure. "Human Resource Management Review," 16, 12-28], in a pharmaceutical manufacturing site. Central to the model…

What Do Phonological Processing Errors Tell about Students' Skills in Reading, Writing, and Oral Language?

ERIC Educational Resources Information Center

Choi, Dowon; Hatcher, Ryan C.; Dulong-Langley, Susan; Liu, Xiaochen; Bray, Melissa A.; Courville, Troy; O'Brien, Rebecca; DeBiase, Emily

2017-01-01

The kinds of errors that children and adolescents make on phonological processing tasks were studied with a large sample between ages 4 and 19 (N = 3,842) who were tested on the Kaufman Test of Educational Achievement-Third Edition (KTEA-3). Principal component analysis identified two phonological processing factors: Basic Phonological Awareness…

Configural and component processing in simultaneous and sequential lineup procedures.

PubMed

Flowe, Heather D; Smith, Harriet M J; Karoğlu, Nilda; Onwuegbusi, Tochukwu O; Rai, Lovedeep

2016-01-01

Configural processing supports accurate face recognition, yet it has never been examined within the context of criminal identification lineups. We tested, using the inversion paradigm, the role of configural processing in lineups. Recent research has found that face discrimination accuracy in lineups is better in a simultaneous compared to a sequential lineup procedure. Therefore, we compared configural processing in simultaneous and sequential lineups to examine whether there are differences. We had participants view a crime video, and then they attempted to identify the perpetrator from a simultaneous or sequential lineup. The test faces were presented either upright or inverted, as previous research has shown that inverting test faces disrupts configural processing. The size of the inversion effect for faces was the same across lineup procedures, indicating that configural processing underlies face recognition in both procedures. Discrimination accuracy was comparable across lineup procedures in both the upright and inversion condition. Theoretical implications of the results are discussed.

Investigation of the microbial community structure and activity as indicators of compost stability and composting process evolution.

PubMed

Chroni, Christina; Kyriacou, Adamadini; Manios, Thrassyvoulos; Lasaridi, Konstantia-Ekaterini

2009-08-01

In a bid to identify suitable microbial indicators of compost stability, the process evolution during windrow composting of poultry manure (PM), green waste (GW) and biowaste was studied. Treatments were monitored with regard to abiotic factors, respiration activity (determined using the SOUR test) and functional microflora. The composting process went through typical changes in temperature, moisture content and microbial properties, despite the inherent feedstock differences. Nitrobacter and pathogen indicators varied as a monotonous function of processing time. Some microbial groups have shown a potential to serve as fingerprints of the different process stages, but still they should be examined in context with respirometric tests and abiotic parameters. Respiration activity reflected well the process stage, verifying the value of respirometric tests to access compost stability. SOUR values below 1 mg O(2)/g VS/h were achieved for the PM and the GW compost.

Evaluation of Fracture Initiation in the Mannesmann Piercing Process

NASA Astrophysics Data System (ADS)

Fanini, S.; Ghiotti, A.; Bruschi, S.

2007-04-01

One of the challenging objectives in studying the Mannesmann piercing process is to predict the fracture initiation, known as "Mannesmann effect", in order to design and optimize the working parameters of the piercing process. The objective of the paper is to investigate the workability of a tube steel tested in the same conditions of the Mannesman piercing process. The stress and strain states as well as temperature fields arising during the process are identified through numerical simulations. The hot tensile test is chosen for fundamental studies on fracture initiation, as a tensile state of stress in the centre of the billet in the first stages of the piercing process before the plug arrival seems to be one of the main causes of the crack initiation. The material constants of energy-based models implemented in FEM codes are calculated and numerical results are compared with non-plug piercing tests carried out on the industrial plant.

The Careful Puppet Master: Reducing risk and fortifying acceptance testing with Jenkins CI

NASA Astrophysics Data System (ADS)

Smith, Jason A.; Richman, Gabriel; DeStefano, John; Pryor, James; Rao, Tejas; Strecker-Kellogg, William; Wong, Tony

2015-12-01

Centralized configuration management, including the use of automation tools such as Puppet, can greatly increase provisioning speed and efficiency when configuring new systems or making changes to existing systems, reduce duplication of work, and improve automated processes. However, centralized management also brings with it a level of inherent risk: a single change in just one file can quickly be pushed out to thousands of computers and, if that change is not properly and thoroughly tested and contains an error, could result in catastrophic damage to many services, potentially bringing an entire computer facility offline. Change management procedures can—and should—be formalized in order to prevent such accidents. However, like the configuration management process itself, if such procedures are not automated, they can be difficult to enforce strictly. Therefore, to reduce the risk of merging potentially harmful changes into our production Puppet environment, we have created an automated testing system, which includes the Jenkins CI tool, to manage our Puppet testing process. This system includes the proposed changes and runs Puppet on a pool of dozens of RedHat Enterprise Virtualization (RHEV) virtual machines (VMs) that replicate most of our important production services for the purpose of testing. This paper describes our automated test system and how it hooks into our production approval process for automatic acceptance testing. All pending changes that have been pushed to production must pass this validation process before they can be approved and merged into production.

Improving Papanicolaou test quality and reducing medical errors by using Toyota production system methods.

PubMed

Raab, Stephen S; Andrew-Jaja, Carey; Condel, Jennifer L; Dabbs, David J

2006-01-01

The objective of the study was to determine whether the Toyota production system process improves Papanicolaou test quality and patient safety. An 8-month nonconcurrent cohort study that included 464 case and 639 control women who had a Papanicolaou test was performed. Office workflow was redesigned using Toyota production system methods by introducing a 1-by-1 continuous flow process. We measured the frequency of Papanicolaou tests without a transformation zone component, follow-up and Bethesda System diagnostic frequency of atypical squamous cells of undetermined significance, and diagnostic error frequency. After the intervention, the percentage of Papanicolaou tests lacking a transformation zone component decreased from 9.9% to 4.7% (P = .001). The percentage of Papanicolaou tests with a diagnosis of atypical squamous cells of undetermined significance decreased from 7.8% to 3.9% (P = .007). The frequency of error per correlating cytologic-histologic specimen pair decreased from 9.52% to 7.84%. The introduction of the Toyota production system process resulted in improved Papanicolaou test quality.

Multi-parameter comparison of a standardized mixed meal tolerance test in healthy and type 2 diabetic subjects: the PhenFlex challenge.

PubMed

Wopereis, Suzan; Stroeve, Johanna H M; Stafleu, Annette; Bakker, Gertruud C M; Burggraaf, Jacobus; van Erk, Marjan J; Pellis, Linette; Boessen, Ruud; Kardinaal, Alwine A F; van Ommen, Ben

2017-01-01

A key feature of metabolic health is the ability to adapt upon dietary perturbations. Recently, it was shown that metabolic challenge tests in combination with the new generation biomarkers allow the simultaneous quantification of major metabolic health processes. Currently, applied challenge tests are largely non-standardized. A systematic review defined an optimal nutritional challenge test, the "PhenFlex test" (PFT). This study aimed to prove that PFT modulates all relevant processes governing metabolic health thereby allowing to distinguish subjects with different metabolic health status. Therefore, 20 healthy and 20 type 2 diabetic (T2D) male subjects were challenged both by PFT and oral glucose tolerance test (OGTT). During the 8-h response time course, 132 parameters were quantified that report on 26 metabolic processes distributed over 7 organs (gut, liver, adipose, pancreas, vasculature, muscle, kidney) and systemic stress. In healthy subjects, 110 of the 132 parameters showed a time course response. Patients with T2D showed 18 parameters to be significantly different after overnight fasting compared to healthy subjects, while 58 parameters were different in the post-challenge time course after the PFT. This demonstrates the added value of PFT in distinguishing subjects with different health status. The OGTT and PFT response was highly comparable for glucose metabolism as identical amounts of glucose were present in both challenge tests. Yet the PFT reports on additional processes, including vasculature, systemic stress, and metabolic flexibility. The PFT enables the quantification of all relevant metabolic processes involved in maintaining or regaining homeostasis of metabolic health. Studying both healthy subjects and subjects with impaired metabolic health showed that the PFT revealed new processes laying underneath health. This study provides the first evidence towards adopting the PFT as gold standard in nutrition research.

AIDS

MedlinePlus

... people with HIV infection and AIDS. Exams and Tests DIAGNOSTIC TESTS These are tests that are done to check if you've ... general, testing is a 2-step process: Screening test. There are several kinds of tests. Some are ...

Preappointment testing for BRAF/KIT mutation in advanced melanoma: a model in molecular data delivery for individualized medicine.

PubMed

Mounajjed, Taofic; Brown, Char L; Stern, Therese K; Bjorheim, Annette M; Bridgeman, Andrew J; Rumilla, Kandelaria M; McWilliams, Robert R; Flotte, Thomas J

2014-11-01

The emergence of individualized medicine is driven by developments in precision diagnostics, epitomized by molecular testing. Because treatment decisions are being made based on such molecular data, data management is gaining major importance. Among data management challenges, creating workflow solutions for timely delivery of molecular data has become pivotal. This study aims to design and implement a scalable process that permits preappointment BRAF/KIT mutation analysis in melanoma patients, allowing molecular results necessary for treatment plans to be available before the patient's appointment. Process implementation aims to provide a model for efficient molecular data delivery for individualized medicine. We examined the existing process of BRAF/KIT testing in melanoma patients visiting our institution for oncology consultation. We created 5 working groups, each designing a specific segment of an alternative process that would allow preappointment BRAF/KIT testing and delivery of results. Data were captured and analyzed to evaluate the success of the alternative process. For 1 year, 35 (59%) of 55 patients had prior BRAF/KIT testing. The remaining 20 patients went through the new process of preappointment testing; results were available at the time of appointment for 12 patients (overall preappointment results availability, 85.5%). The overall process averaged 13.4 ± 4.7 days. In conclusion, we describe the successful implementation of a scalable workflow solution that permits preappointment BRAF/KIT mutation analysis and result delivery in melanoma patients. This sets the stage for further applications of this model to other conditions, answering an increasing demand for robust delivery of molecular data for individualized medicine. Copyright © 2014 Elsevier Inc. All rights reserved.

Evaluation of the dermal carcinogenicity of lubricant base oils by the mouse skin painting bioassay and other proposed methods.

PubMed

Chasey, K L; McKee, R H

1993-01-01

Lubricant base oils are petroleum products that are predominantly derived from the vacuum distillation of crude oil. Various types of refinement can be employed during the manufacturing process, and evidence suggests that certain of the associated process streams produce skin cancer. Polycyclic aromatic compounds (PACs), some of which are considered as the causative agents, are removed, concentrated or chemically converted during the refinement process. In order to understand the effects of various types of refinement processes on carcinogenic potential, 94 oils were evaluated in the mouse epidermal cancer bioassay. This Exxon database is unique, because of the wide range of crude oils and processing histories represented. Seven processing history classifications are described, and conclusions concerning the impacts of each refinement process on dermal carcinogenicity are discussed. This research also included an evaluation of selected biological and chemical test methods for predicting carcinogenic potential. These included a modified version of the Ames test for mutagenicity, as well as analytical characterizations of the polycyclic aromatic structures in the oils. For classification purposes, a sample was considered to be carcinogenic if it resulted in the production of two or more tumor-bearing animals (in test groups of either 40 or 50 animals). The modified Ames test was considered to be positive if the mutagenicity index was > or = 2.0, and PAC analyses were similarly designated as positive or negative according to proposed guidelines. All of the alternative test methods showed similar agreement with dermal carcinogenicity bioassay data; concordance values were > or = 80%. However, each test was incorrect in ca. 10%-20% of the cases evaluated.(ABSTRACT TRUNCATED AT 250 WORDS)

Spacecraft Testing Programs: Adding Value to the Systems Engineering Process

NASA Technical Reports Server (NTRS)

Britton, Keith J.; Schaible, Dawn M.

2011-01-01

Testing has long been recognized as a critical component of spacecraft development activities - yet many major systems failures may have been prevented with more rigorous testing programs. The question is why is more testing not being conducted? Given unlimited resources, more testing would likely be included in a spacecraft development program. Striking the right balance between too much testing and not enough has been a long-term challenge for many industries. The objective of this paper is to discuss some of the barriers, enablers, and best practices for developing and sustaining a strong test program and testing team. This paper will also explore the testing decision factors used by managers; the varying attitudes toward testing; methods to develop strong test engineers; and the influence of behavior, culture and processes on testing programs. KEY WORDS: Risk, Integration and Test, Validation, Verification, Test Program Development

Waste water processing technology for Space Station Freedom - Comparative test data analysis

NASA Technical Reports Server (NTRS)

Miernik, Janie H.; Shah, Burt H.; Mcgriff, Cindy F.

1991-01-01

Comparative tests were conducted to choose the optimum technology for waste water processing on SSF. A thermoelectric integrated membrane evaporation (TIMES) subsystem and a vapor compression distillation subsystem (VCD) were built and tested to compare urine processing capability. Water quality, performance, and specific energy were compared for conceptual designs intended to function as part of the water recovery and management system of SSF. The VCD is considered the most mature and efficient technology and was selected to replace the TIMES as the baseline urine processor for SSF.

Successful MPPF Pneumatics Verification and Validation Testing

NASA Image and Video Library

2017-03-28

Engineers and technicians completed verification and validation testing of several pneumatic systems inside and outside the Multi-Payload Processing Facility (MPPF) at NASA's Kennedy Space Center in Florida. In view is the service platform for Orion spacecraft processing. The MPPF will be used for offline processing and fueling of the Orion spacecraft and service module stack before launch. Orion also will be de-serviced in the MPPF after a mission. The Ground Systems Development and Operations Program (GSDO) is overseeing upgrades to the facility. The Engineering Directorate led the recent pneumatic tests.

Successful MPPF Pneumatics Verification and Validation Testing

NASA Image and Video Library

2017-03-28

Engineers and technicians completed verification and validation testing of several pneumatic systems inside and outside the Multi-Payload Processing Facility (MPPF) at NASA's Kennedy Space Center in Florida. In view is the top level of the service platform for Orion spacecraft processing. The MPPF will be used for offline processing and fueling of the Orion spacecraft and service module stack before launch. Orion also will be de-serviced in the MPPF after a mission. The Ground Systems Development and Operations Program (GSDO) is overseeing upgrades to the facility. The Engineering Directorate led the recent pneumatic tests.

The challenge of cross-cultural assessment--The Test of Ability To Explain for Zulu-speaking Children.

PubMed

Solarsh, Barbara; Alant, Erna

2006-01-01

A culturally appropriate test, The Test of Ability To Explain for Zulu-speaking Children (TATE-ZC), was developed to measure verbal problem solving skills of rural, Zulu-speaking, primary school children. Principles of 'non-biased' assessment, as well as emic (culture specific) and etic (universal) aspects of intelligence formed the theoretical backdrop. In addition, specific principles relating to test translation; test content; culturally appropriate stimulus material; scoring procedures and test administration were applied. Five categories of abstract thinking skills formed the basis of the TATE-ZC. These were: (a) Explaining Inferences, (b) Determining Cause, (c) Negative Why Questions, (d) Determining Solutions and (e) Avoiding Problem. The process of test development underwent three pilot studies. Results indicate that the TATE-ZC is a reliable and valid test for the target population. A critical analysis of the efficacy of creating a test of verbal reasoning for children from the developing world concludes the article. As a result of this activity (1) the participant will have a clearer understanding of the principles that need to be followed when developing culturally appropriate test material; (2) the participant will understand the process of developing culturally appropriate test material for non-mainstream cultures; (3) the participant will be able to apply the process and principles to other cross-cultural testing situations.

Using pattern enumeration to accelerate process development and ramp yield

NASA Astrophysics Data System (ADS)

Zhuang, Linda; Pang, Jenny; Xu, Jessy; Tsai, Mengfeng; Wang, Amy; Zhang, Yifan; Sweis, Jason; Lai, Ya-Chieh; Ding, Hua

2016-03-01

During a new technology node process setup phase, foundries do not initially have enough product chip designs to conduct exhaustive process development. Different operational teams use manually designed simple test keys to set up their process flows and recipes. When the very first version of the design rule manual (DRM) is ready, foundries enter the process development phase where new experiment design data is manually created based on these design rules. However, these IP/test keys contain very uniform or simple design structures. This kind of design normally does not contain critical design structures or process unfriendly design patterns that pass design rule checks but are found to be less manufacturable. It is desired to have a method to generate exhaustive test patterns allowed by design rules at development stage to verify the gap of design rule and process. This paper presents a novel method of how to generate test key patterns which contain known problematic patterns as well as any constructs which designers could possibly draw based on current design rules. The enumerated test key patterns will contain the most critical design structures which are allowed by any particular design rule. A layout profiling method is used to do design chip analysis in order to find potential weak points on new incoming products so fab can take preemptive action to avoid yield loss. It can be achieved by comparing different products and leveraging the knowledge learned from previous manufactured chips to find possible yield detractors.

Quality Indicators for the Total Testing Process.

PubMed

Plebani, Mario; Sciacovelli, Laura; Aita, Ada

2017-03-01

ISO 15189:2012 requires the use of quality indicators (QIs) to monitor and evaluate all steps of the total testing process, but several difficulties dissuade laboratories from effective and continuous use of QIs in routine practice. An International Federation of Clinical Chemistry and Laboratory Medicine working group addressed this problem and implemented a project to develop a model of QIs to be used in clinical laboratories worldwide to monitor and evaluate all steps of the total testing process, and decrease error rates and improve patient services in laboratory testing. All laboratories are invited, at no cost, to enroll in the project and contribute to harmonized management at the international level. Copyright © 2016 Elsevier Inc. All rights reserved.

Computed Tomography and Thermography Increases CMC Material and Process Development Efficiency and Testing Effectiveness

NASA Technical Reports Server (NTRS)

Effinger, Michael; Beshears, Ron; Hufnagle, David; Walker, James; Russell, Sam; Stowell, Bob; Myers, David

2002-01-01

Nondestructive characterization techniques have been used to steer development and testing of CMCs. Computed tomography is used to determine the volumetric integrity of the CMC plates and components. Thermography is used to determine the near surface integrity of the CMC plates and components. For process and material development, information such as density uniformity, part delamination, and dimensional tolerance conformity is generated. The information from the thermography and computed tomography is correlated and then specimen cutting maps are superimposed on the thermography images. This enables for tighter data and potential explanation of off nominal test data. Examples of nondestructive characterization utilization to make decisions in process and material development and testing are presented.

A preliminary 'test case' manufacturing sequence for 50 cents/watt solar photovoltaic modules in 1986

NASA Technical Reports Server (NTRS)

Bickler, D. B.

1979-01-01

The paper describes a 'test case' manufacturing process sequence for solar photovoltaic modules which will cost 50 cents/watt in 1986. The process, which starts with the purification of silicon grown into 75-mm-wide thin ribbons, is discussed, and the plant layout is depicted; each department is sized to produce 250 MW of modules/per year. The cost of this process sequence is compared to present technology at various companies showing considerable spread for each process; data are tabulated in a composite state-of-the-art cell processing cost summary for these processes.

Ground Handling of Batteries at Test and Launch-site Facilities

NASA Technical Reports Server (NTRS)

Jeevarajan, Judith A.; Hohl, Alan R.

2008-01-01

Ground handling of flight as well as engineering batteries at test facilities and launch-site facilities is a safety critical process. Test equipment interfacing with the batteries should have the required controls to prevent a hazardous failure of the batteries. Test equipment failures should not induce catastrophic failures on the batteries. Transportation requirements for batteries should also be taken into consideration for safe transportation. This viewgraph presentation includes information on the safe handling of batteries for ground processing at test facilities as well as launch-site facilities.

Hydrologic Source Term Processes and Models for the Clearwater and Wineskin Tests, Rainier Mesa, Nevada National Security Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carle, Steven F.

2011-05-04

This report describes the development, processes, and results of a hydrologic source term (HST) model for the CLEARWATER (U12q) and WINESKIN (U12r) tests located on Rainier Mesa, Nevada National Security Site, Nevada (Figure 1.1). Of the 61 underground tests (involving 62 unique detonations) conducted on Rainier Mesa (Area 12) between 1957 and 1992 (USDOE, 2015), the CLEARWATER and WINESKIN tests present many unique features that warrant a separate HST modeling effort from other Rainier Mesa tests.

A methodology of SiP testing based on boundary scan

NASA Astrophysics Data System (ADS)

Qin, He; Quan, Haiyang; Han, Yifei; Zhu, Tianrui; Zheng, Tuo

2017-10-01

System in Package (SiP) play an important role in portable, aerospace and military electronic with the microminiaturization, light weight, high density, and high reliability. At present, SiP system test has encountered the problem on system complexity and malfunction location with the system scale exponentially increase. For SiP system, this paper proposed a testing methodology and testing process based on the boundary scan technology. Combining the character of SiP system and referencing the boundary scan theory of PCB circuit and embedded core test, the specific testing methodology and process has been proposed. The hardware requirement of the under test SiP system has been provided, and the hardware platform of the testing has been constructed. The testing methodology has the character of high test efficiency and accurate malfunction location.

Effect of Friction Stir Process Parameters on the Mechanical and Thermal Behavior of 5754-H111 Aluminum Plates.

PubMed

Serio, Livia Maria; Palumbo, Davide; De Filippis, Luigi Alberto Ciro; Galietti, Umberto; Ludovico, Antonio Domenico

2016-02-23

A study of the Friction Stir Welding (FSW) process was carried out in order to evaluate the influence of process parameters on the mechanical properties of aluminum plates (AA5754-H111). The process was monitored during each test by means of infrared cameras in order to correlate temperature information with eventual changes of the mechanical properties of joints. In particular, two process parameters were considered for tests: the welding tool rotation speed and the welding tool traverse speed. The quality of joints was evaluated by means of destructive and non-destructive tests. In this regard, the presence of defects and the ultimate tensile strength (UTS) were investigated for each combination of the process parameters. A statistical analysis was carried out to assess the correlation between the thermal behavior of joints and the process parameters, also proving the capability of Infrared Thermography for on-line monitoring of the quality of joints.

Technology’s present situation and the development prospects of energy efficiency monitoring as well as performance testing & analysis for process flow compressors

NASA Astrophysics Data System (ADS)

Li, L.; Zhao, Y.; Wang, L.; Yang, Q.; Liu, G.; Tang, B.; Xiao, J.

2017-08-01

In this paper, the background of performance testing of in-service process flow compressors set in user field are introduced, the main technique barriers faced in the field test are summarized, and the factors that result in real efficiencies of most process flow compressors being lower than the guaranteed by manufacturer are analysed. The authors investigated the present operational situation of process flow compressors in China and found that low efficiency operation of flow compressors is because the compressed gas is generally forced to flow back into the inlet pipe for adapting to the process parameters variety. For example, the anti-surge valve is always opened for centrifugal compressor. To improve the operation efficiency of process compressors the energy efficiency monitoring technology was overviewed and some suggestions are proposed in the paper, which is the basis of research on energy efficiency evaluation and/or labelling of process compressors.

Effect of Friction Stir Process Parameters on the Mechanical and Thermal Behavior of 5754-H111 Aluminum Plates

PubMed Central

Serio, Livia Maria; Palumbo, Davide; De Filippis, Luigi Alberto Ciro; Galietti, Umberto; Ludovico, Antonio Domenico

2016-01-01

A study of the Friction Stir Welding (FSW) process was carried out in order to evaluate the influence of process parameters on the mechanical properties of aluminum plates (AA5754-H111). The process was monitored during each test by means of infrared cameras in order to correlate temperature information with eventual changes of the mechanical properties of joints. In particular, two process parameters were considered for tests: the welding tool rotation speed and the welding tool traverse speed. The quality of joints was evaluated by means of destructive and non-destructive tests. In this regard, the presence of defects and the ultimate tensile strength (UTS) were investigated for each combination of the process parameters. A statistical analysis was carried out to assess the correlation between the thermal behavior of joints and the process parameters, also proving the capability of Infrared Thermography for on-line monitoring of the quality of joints. PMID:28773246

Redox Control For Hanford HLW Feeds VSL-12R2530-1, REV 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, A. A.; Matlack, Keith S.; Pegg, Ian L.

2012-12-13

The principal objectives of this work were to investigate the effects of processing simulated Hanford HLW at the estimated maximum concentrations of nitrates and oxalates and to identify strategies to mitigate any processing issues resulting from high concentrations of nitrates and oxalates. This report provides results for a series of tests that were performed on the DM10 melter system with simulated C-106/AY-102 HLW. The tests employed simulated HLW feeds containing variable amounts of nitrates and waste organic compounds corresponding to maximum concentrations proj ected for Hanford HLW streams in order to determine their effects on glass production rate, processing characteristics,more » glass redox conditions, melt pool foaming, and the tendency to form secondary phases. Such melter tests provide information on key process factors such as feed processing behavior, dynamic effects during processing, processing rates, off-gas amounts and compositions, foaming control, etc., that cannot be reliably obtained from crucible melts.« less

Value stream mapping of the Pap test processing procedure: a lean approach to improve quality and efficiency.

PubMed

Michael, Claire W; Naik, Kalyani; McVicker, Michael

2013-05-01

We developed a value stream map (VSM) of the Papanicolaou test procedure to identify opportunities to reduce waste and errors, created a new VSM, and implemented a new process emphasizing Lean tools. Preimplementation data revealed the following: (1) processing time (PT) for 1,140 samples averaged 54 hours; (2) 27 accessioning errors were detected on review of 357 random requisitions (7.6%); (3) 5 of the 20,060 tests had labeling errors that had gone undetected in the processing stage. Four were detected later during specimen processing but 1 reached the reporting stage. Postimplementation data were as follows: (1) PT for 1,355 samples averaged 31 hours; (2) 17 accessioning errors were detected on review of 385 random requisitions (4.4%); and (3) no labeling errors were undetected. Our results demonstrate that implementation of Lean methods, such as first-in first-out processes and minimizing batch size by staff actively participating in the improvement process, allows for higher quality, greater patient safety, and improved efficiency.

Development of Statistical Process Control Methodology for an Environmentally Compliant Surface Cleaning Process in a Bonding Laboratory

NASA Technical Reports Server (NTRS)

Hutchens, Dale E.; Doan, Patrick A.; Boothe, Richard E.

1997-01-01

Bonding labs at both MSFC and the northern Utah production plant prepare bond test specimens which simulate or witness the production of NASA's Reusable Solid Rocket Motor (RSRM). The current process for preparing the bonding surfaces employs 1,1,1-trichloroethane vapor degreasing, which simulates the current RSRM process. Government regulations (e.g., the 1990 Amendments to the Clean Air Act) have mandated a production phase-out of a number of ozone depleting compounds (ODC) including 1,1,1-trichloroethane. In order to comply with these regulations, the RSRM Program is qualifying a spray-in-air (SIA) precision cleaning process using Brulin 1990, an aqueous blend of surfactants. Accordingly, surface preparation prior to bonding process simulation test specimens must reflect the new production cleaning process. The Bonding Lab Statistical Process Control (SPC) program monitors the progress of the lab and its capabilities, as well as certifies the bonding technicians, by periodically preparing D6AC steel tensile adhesion panels with EA-91 3NA epoxy adhesive using a standardized process. SPC methods are then used to ensure the process is statistically in control, thus producing reliable data for bonding studies, and identify any problems which might develop. Since the specimen cleaning process is being changed, new SPC limits must be established. This report summarizes side-by-side testing of D6AC steel tensile adhesion witness panels and tapered double cantilevered beams (TDCBs) using both the current baseline vapor degreasing process and a lab-scale spray-in-air process. A Proceco 26 inches Typhoon dishwasher cleaned both tensile adhesion witness panels and TDCBs in a process which simulates the new production process. The tests were performed six times during 1995, subsequent statistical analysis of the data established new upper control limits (UCL) and lower control limits (LCL). The data also demonstrated that the new process was equivalent to the vapor degreasing process.

[Attempt for development of rapid word reading test for children--evaluation of reliability and validity].

PubMed

Hashimoto, Ryusaku; Kashiwagi, Mitsuru; Suzuki, Shuhei

2008-09-01

We developed a rapid word reading test for examining the phonological processing ability of Japanese children. We prepared two versions of the test, version A and B. Each test has word and non-word tasks. Twenty-two healthy boys of third grade in primary schools participated in this validation study. For criterion related validity, we performed the serial Hiragana reading test, the sentence reading test, Raven's coloured progressive matrices (RCPM), the Token test for children, the Kana word dictation test, the standardized comprehension test of abstract words (SCTAW), and Trail Circle test. The reading times of the newly developed test correlated moderately or highly with those of the serial Hiragana reading test and the sentence reading test. However, the scores of the other tests (RCPM, Token test for children, Kana word dictation test, SCTAW, Trail Circle test) did not correlated with the reading time of the rapid word reading test. Test-retest reliabilities in the word tasks were more than moderate: 0.52 and 0.76 in versions A and B, while those in the non-word tasks were high: 0.91 and 0.88 in versions A and B. The correlation coefficient between versions A and B was 0.7 for the word tasks and 0.92 for the non-word tasks. This study showed that the rapid word reading test has substantial validity and reliability for testing the phonological processing ability of Japanese children. In addition, the non-word tasks were more suitable for selectively examining the speed of the grapheme to phoneme conversion process.

Factor analysis and predictive validity of microcomputer-based tests

NASA Technical Reports Server (NTRS)

Kennedy, R. S.; Baltzley, D. R.; Turnage, J. J.; Jones, M. B.

1989-01-01

11 tests were selected from two microcomputer-based performance test batteries because previously these tests exhibited rapid stability (less than 10 min, of practice) and high retest reliability efficiencies (r greater than 0.707 for each 3 min. of testing). The battery was administered three times to each of 108 college students (48 men and 60 women) and a factor analysis was performed. Two of the three identified factors appear to be related to information processing ("encoding" and "throughput/decoding"), and the third named an "output/speed" factor. The spatial, memory, and verbal tests loaded on the "encoding" factor and included Grammatical Reasoning, Pattern Comparison, Continuous Recall, and Matrix Rotation. The "throughput/decoding" tests included perceptual/numerical tests like Math Processing, Code Substitution, and Pattern Comparison. The output speed factor was identified by Tapping and Reaction Time tests. The Wonderlic Personnel Test was group administered before the first and after the last administration of the performance tests. The multiple Rs in the total sample between combined Wonderlic as a criterion and less than 5 min. of microcomputer testing on Grammatical Reasoning and Math Processing as predictors ranged between 0.41 and 0.52 on the three test administrations. Based on these results, the authors recommend a core battery which, if time permits, would consist of two tests from each factor. Such a battery is now known to permit stable, reliable, and efficient assessment.

PULSE COMBUSTOR DESIGN QUALIFICATION TEST AND CLEAN COAL FEEDSTOCK TEST - VOLUME I AND VOLUME II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

For this Cooperative Agreement, the pulse heater module is the technology envelope for an indirectly heated steam reformer. The field of use of the steam reformer pursuant to this Cooperative Agreement with DOE is for the processing of sub-bituminous coals and lignite. The main focus is the mild gasification of such coals for the generation of both fuel gas and char--for the steel industry is the main focus. An alternate market application for the substitution of metallurgical coke is also presented. This project was devoted to qualification of a 253-tube pulse heater module. This module was designed, fabricated, installed, instrumentedmore » and tested in a fluidized bed test facility. Several test campaigns were conducted. This larger heater is a 3.5 times scale-up of the previous pulse heaters that had 72 tubes each. The smaller heater has been part of previous pilot field testing of the steam reformer at New Bern, North Carolina. The project also included collection and reduction of mild gasification process data from operation of the process development unit (PDU). The operation of the PDU was aimed at conditions required to produce char (and gas) for the Northshore Steel Operations. Northshore Steel supplied the coal for the process unit tests.« less

The stress-corrosion behavior of Al-Li-Cu alloys: A comparison of test methods

NASA Technical Reports Server (NTRS)

Rizzo, P. P.; Galvin, R. P.; Nelson, H. G.

1982-01-01

Two powder metallurgy processed (Al-Li-Cu) alloys with and without Mg addition were studied in aqueous 3.5% NaCl solution during the alternate immersion testing of tuning fork specimens, slow crack growth tests using fracture mechanics specimens, and the slow strain rate testing of straining electrode specimens. Scanning electron microscopy and optical metallography were used to demonstrate the character of the interaction between the Al-Li-Cu alloys and the selected environment. Both alloys are susceptible to SC in an aqueous 3.5% NaCl solution under the right electrochemical and microstructural conditions. Each test method yields important information on the character of the SC behavior. Under all conditions investigated, second phase particles strung out in rows along the extrusion direction in the alloys were rapidly attacked, and played principal role in the SC process. With time, larger pits developed from these rows of smaller pits and under certain electrochemical conditions surface cracks initiated from the larger pits and contributed directly to the fracture process. Evidence to support slow crack growth was observed in both the slow strain rate tests and the sustained immersion tests of precracked fracture mechanics specimens. The possible role of H2 in the stress corrosion cracking process is suggested.

Exact and conceptual repetition dissociate conceptual memory tests: problems for transfer appropriate processing theory.

PubMed

McDermott, K B; Roediger, H L

1996-03-01

Three experiments examined whether a conceptual implicit memory test (specifically, category instance generation) would exhibit repetition effects similar to those found in free recall. The transfer appropriate processing account of dissociations among memory tests led us to predict that the tests would show parallel effects; this prediction was based upon the theory's assumption that conceptual tests will behave similarly as a function of various independent variables. In Experiment 1, conceptual repetition (i.e., following a target word [e.g., puzzles] with an associate [e.g., jigsaw]) did not enhance priming on the instance generation test relative to the condition of simply presenting the target word once, although this manipulation did affect free recall. In Experiment 2, conceptual repetition was achieved by following a picture with its corresponding word (or vice versa). In this case, there was an effect of conceptual repetition on free recall but no reliable effect on category instance generation or category cued recall. In addition, we obtained a picture superiority effect in free recall but not in category instance generation. In the third experiment, when the same study sequence was used as in Experiment 1, but with instructions that encouraged relational processing, priming on the category instance generation task was enhanced by conceptual repetition. Results demonstrate that conceptual memory tests can be dissociated and present problems for Roediger's (1990) transfer appropriate processing account of dissociations between explicit and implicit tests.

PROCESS WATER BUILDING, TRA605. INSIDE A FLASH EVAPORATOR. INL NEGATIVE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PROCESS WATER BUILDING, TRA-605. INSIDE A FLASH EVAPORATOR. INL NEGATIVE NO. 3323. Unknown Photographer, 9/12/1951 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Episodic, generalized, and semantic memory tests: switching and strength effects.

PubMed

Humphreys, Michael S; Murray, Krista L

2011-09-01

We continue the process of investigating the probabilistic paired associate paradigm in an effort to understand the memory access control processes involved and to determine whether the memory structure produced is in transition between episodic and semantic memory. In this paradigm two targets are probabilistically paired with a cue across a large number of short lists. Participants can recall the target paired with the cue in the most recent list (list specific test), produce the first of the two targets that have been paired with that cue to come to mind (generalised test), and produce a free association response (semantic test). Switching between a generalised test and a list specific test did not produce a switching cost indicating a general similarity in the control processes involved. In addition, there was evidence for a dissociation between two different strength manipulations (amount of study time and number of cue-target pairings) such that number of pairings influenced the list specific, generalised and the semantic test but amount of study time only influenced the list specific and generalised test. © 2011 Canadian Psychological Association

TQM in a test environment

NASA Technical Reports Server (NTRS)

Chambers, Gary D.; King, Elizabeth A.; Oleson, Keith

1992-01-01

In response to the changing aerospace economic climate, Martin Marietta Astronautics Group (MMAG) has adopted a Total Quality Management (TQM) philosophy to maintain a competitive edge. TQM emphasizes continuous improvement of processes, motivation to improve from within, cross-functional involvement, people empowerment, customer satisfaction, and modern process control techniques. The four major initiatives of TQM are Product Excellence, Manufacturing Resource Planning (MRP II), People Empowerment, and Subcontract Management. The Defense Space and Communications (DS&C) Test Lab's definition and implementation of the MRP II and people empowerment initiatives within TQM are discussed. The application of MRP II to environmental test planning and operations processes required a new and innovative approach. In an 18 month span, the test labs implemented MRP II and people empowerment and achieved a Class 'A' operational status. This resulted in numerous benefits, both tangible and intangible, including significant cost savings and improved quality of life. A detailed description of the implementation process and results are addressed.

Solutions for acceleration measurement in vehicle crash tests

NASA Astrophysics Data System (ADS)

Dima, D. S.; Covaciu, D.

2017-10-01

Crash tests are useful for validating computer simulations of road traffic accidents. One of the most important parameters measured is the acceleration. The evolution of acceleration versus time, during a crash test, form a crash pulse. The correctness of the crash pulse determination depends on the data acquisition system used. Recommendations regarding the instrumentation for impact tests are given in standards, which are focused on the use of accelerometers as impact sensors. The goal of this paper is to present the device and software developed by authors for data acquisition and processing. The system includes two accelerometers with different input ranges, a processing unit based on a 32-bit microcontroller and a data logging unit with SD card. Data collected on card, as text files, is processed with a dedicated software running on personal computers. The processing is based on diagrams and includes the digital filters recommended in standards.

Refining and end use study of coal liquids II - linear programming analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowe, C.; Tam, S.

1995-12-31

A DOE-funded study is underway to determine the optimum refinery processing schemes for producing transportation fuels that will meet CAAA regulations from direct and indirect coal liquids. The study consists of three major parts: pilot plant testing of critical upgrading processes, linear programming analysis of different processing schemes, and engine emission testing of final products. Currently, fractions of a direct coal liquid produced form bituminous coal are being tested in sequence of pilot plant upgrading processes. This work is discussed in a separate paper. The linear programming model, which is the subject of this paper, has been completed for themore » petroleum refinery and is being modified to handle coal liquids based on the pilot plant test results. Preliminary coal liquid evaluation studies indicate that, if a refinery expansion scenario is adopted, then the marginal value of the coal liquid (over the base petroleum crude) is $3-4/bbl.« less

TQM in a test environment

NASA Astrophysics Data System (ADS)

Chambers, Gary D.; King, Elizabeth A.; Oleson, Keith

1992-11-01

In response to the changing aerospace economic climate, Martin Marietta Astronautics Group (MMAG) has adopted a Total Quality Management (TQM) philosophy to maintain a competitive edge. TQM emphasizes continuous improvement of processes, motivation to improve from within, cross-functional involvement, people empowerment, customer satisfaction, and modern process control techniques. The four major initiatives of TQM are Product Excellence, Manufacturing Resource Planning (MRP II), People Empowerment, and Subcontract Management. The Defense Space and Communications (DS&C) Test Lab's definition and implementation of the MRP II and people empowerment initiatives within TQM are discussed. The application of MRP II to environmental test planning and operations processes required a new and innovative approach. In an 18 month span, the test labs implemented MRP II and people empowerment and achieved a Class 'A' operational status. This resulted in numerous benefits, both tangible and intangible, including significant cost savings and improved quality of life. A detailed description of the implementation process and results are addressed.

Advanced composite rudders for DC-10 aircraft: Design, manufacturing, and ground tests

NASA Technical Reports Server (NTRS)

Lehman, G. M.; Purdy, D. M.; Cominsky, A.; Hawley, A. V.; Amason, M. P.; Kung, J. T.; Palmer, R. J.; Purves, N. B.; Marra, P. J.; Hancock, G. R.

1976-01-01

Design synthesis, tooling and process development, manufacturing, and ground testing of a graphite epoxy rudder for the DC-10 commercial transport are discussed. The composite structure was fabricated using a unique processing method in which the thermal expansion characteristics of rubber tooling mandrels were used to generate curing pressures during an oven cure cycle. The ground test program resulted in certification of the rudder for passenger-carrying flights. Results of the structural and environmental tests are interpreted and detailed development of the rubber tooling and manufacturing process is described. Processing, tooling, and manufacturing problems encountered during fabrication of four development rudders and ten flight-service rudders are discussed and the results of corrective actions are described. Non-recurring and recurring manufacturing labor man-hours are tabulated at the detailed operation level. A weight reduction of 13.58 kg (33 percent) was attained in the composite rudder.

Central auditory processing and migraine: a controlled study.

PubMed

Agessi, Larissa Mendonça; Villa, Thaís Rodrigues; Dias, Karin Ziliotto; Carvalho, Deusvenir de Souza; Pereira, Liliane Desgualdo

2014-11-08

This study aimed to verify and compare central auditory processing (CAP) performance in migraine with and without aura patients and healthy controls. Forty-one volunteers of both genders, aged between 18 and 40 years, diagnosed with migraine with and without aura by the criteria of "The International Classification of Headache Disorders" (ICDH-3 beta) and a control group of the same age range and with no headache history, were included. Gaps-in-noise (GIN), Duration Pattern test (DPT) and Dichotic Digits Test (DDT) tests were used to assess central auditory processing performance. The volunteers were divided into 3 groups: Migraine with aura (11), migraine without aura (15), and control group (15), matched by age and schooling. Subjects with aura and without aura performed significantly worse in GIN test for right ear (p = .006), for left ear (p = .005) and for DPT test (p < .001) when compared with controls without headache, however no significant differences were found in the DDT test for the right ear (p = .362) and for the left ear (p = .190). Subjects with migraine performed worsened in auditory gap detection, in the discrimination of short and long duration. They also presented impairment in the physiological mechanism of temporal processing, especially in temporal resolution and temporal ordering when compared with controls. Migraine could be related to an impaired central auditory processing. Research Ethics Committee (CEP 0480.10) - UNIFESP.

Stability of prebiotic, laminaran oligosaccharide under food processing conditions

NASA Astrophysics Data System (ADS)

Chamidah, A.

2018-04-01

Prebiotic stability tests on laminaran oligosaccharide under food processing conditions were urgently performed to determine the ability of prebiotics deal with processing. Laminaran, oligosaccharide is produced from enzymatic hydrolysis. To further apply this prebiotic, it is necessary to test its performance on food processing. Single prebiotic or in combination with probiotic can improve human digestive health. The effectiveness evaluation of prebiotic should be taken into account in regards its chemical and functional stabilities. This study aims to investigate the stability of laminaran, oligosaccharide under food processing condition.

Space processing applications rocket project SPAR 4, engineering report

NASA Technical Reports Server (NTRS)

Reeves, F. (Compiler)

1980-01-01

The materials processing experiments in space, conducted on the SPAR 4 Black Brant VC rocket, are described and discussed. The SPAR 4 payload configuration, the rocket performance, and the flight sequence are reported. The results, analyses, and anomalies of the four experiments are discussed. The experiments conducted were the uniform dispersions of crystallization processing, the contained polycrstalline solidification in low gravity, the containerless processing of ferromagnetic materials, and the containerless processing technology. The instrumentation operations, payload power relay anomaly, relay postflight operational test, and relay postflight shock test are reported.

New Tests to Measure Individual Differences in Matching and Labelling Facial Expressions of Emotion, and Their Association with Ability to Recognise Vocal Emotions and Facial Identity

PubMed Central

Palermo, Romina; O’Connor, Kirsty B.; Davis, Joshua M.; Irons, Jessica; McKone, Elinor

2013-01-01

Although good tests are available for diagnosing clinical impairments in face expression processing, there is a lack of strong tests for assessing “individual differences” – that is, differences in ability between individuals within the typical, nonclinical, range. Here, we develop two new tests, one for expression perception (an odd-man-out matching task in which participants select which one of three faces displays a different expression) and one additionally requiring explicit identification of the emotion (a labelling task in which participants select one of six verbal labels). We demonstrate validity (careful check of individual items, large inversion effects, independence from nonverbal IQ, convergent validity with a previous labelling task), reliability (Cronbach’s alphas of.77 and.76 respectively), and wide individual differences across the typical population. We then demonstrate the usefulness of the tests by addressing theoretical questions regarding the structure of face processing, specifically the extent to which the following processes are common or distinct: (a) perceptual matching and explicit labelling of expression (modest correlation between matching and labelling supported partial independence); (b) judgement of expressions from faces and voices (results argued labelling tasks tap into a multi-modal system, while matching tasks tap distinct perceptual processes); and (c) expression and identity processing (results argued for a common first step of perceptual processing for expression and identity). PMID:23840821

Application of annular centrifugal contactors in the hot test of the improved total partitioning process for high level liquid waste.

PubMed

Duan, Wuhua; Chen, Jing; Wang, Jianchen; Wang, Shuwei; Feng, Xiaogui; Wang, Xinghai; Li, Shaowei; Xu, Chao

2014-08-15

High level liquid waste (HLLW) produced from the reprocessing of the spent nuclear fuel still contains moderate amounts of uranium, transuranium (TRU) actinides, (90)Sr, (137)Cs, etc., and thus constitutes a permanent hazard to the environment. The partitioning and transmutation (P&T) strategy has increasingly attracted interest for the safe treatment and disposal of HLLW, in which the partitioning of HLLW is one of the critical technical issues. An improved total partitioning process, including a TRPO (tri-alkylphosphine oxide) process for the removal of actinides, a CESE (crown ether strontium extraction) process for the removal of Sr, and a CECE (calixcrown ether cesium extraction) process for the removal of Cs, has been developed to treat Chinese HLLW. A 160-hour hot test of the improved total partitioning process was carried out using 72-stage 10-mm-dia annular centrifugal contactors (ACCs) and genuine HLLW. The hot test results showed that the average DFs of total α activity, Sr and Cs were 3.57 × 10(3), 2.25 × 10(4) and 1.68 × 10(4) after the hot test reached equilibrium, respectively. During the hot test, 72-stage 10-mm-dia ACCs worked stable, continuously with no stage failing or interruption of the operation. Copyright © 2014 Elsevier B.V. All rights reserved.

Proposal for a new categorization of aseptic processing facilities based on risk assessment scores.

PubMed

Katayama, Hirohito; Toda, Atsushi; Tokunaga, Yuji; Katoh, Shigeo

2008-01-01

Risk assessment of aseptic processing facilities was performed using two published risk assessment tools. Calculated risk scores were compared with experimental test results, including environmental monitoring and media fill run results, in three different types of facilities. The two risk assessment tools used gave a generally similar outcome. However, depending on the tool used, variations were observed in the relative scores between the facilities. For the facility yielding the lowest risk scores, the corresponding experimental test results showed no contamination, indicating that these ordinal testing methods are insufficient to evaluate this kind of facility. A conventional facility having acceptable aseptic processing lines gave relatively high risk scores. The facility showing a rather high risk score demonstrated the usefulness of conventional microbiological test methods. Considering the significant gaps observed in calculated risk scores and in the ordinal microbiological test results between advanced and conventional facilities, we propose a facility categorization based on risk assessment. The most important risk factor in aseptic processing is human intervention. When human intervention is eliminated from the process by advanced hardware design, the aseptic processing facility can be classified into a new risk category that is better suited for assuring sterility based on a new set of criteria rather than on currently used microbiological analysis. To fully benefit from advanced technologies, we propose three risk categories for these aseptic facilities.

New tests to measure individual differences in matching and labelling facial expressions of emotion, and their association with ability to recognise vocal emotions and facial identity.

PubMed

Palermo, Romina; O'Connor, Kirsty B; Davis, Joshua M; Irons, Jessica; McKone, Elinor

2013-01-01

Although good tests are available for diagnosing clinical impairments in face expression processing, there is a lack of strong tests for assessing "individual differences"--that is, differences in ability between individuals within the typical, nonclinical, range. Here, we develop two new tests, one for expression perception (an odd-man-out matching task in which participants select which one of three faces displays a different expression) and one additionally requiring explicit identification of the emotion (a labelling task in which participants select one of six verbal labels). We demonstrate validity (careful check of individual items, large inversion effects, independence from nonverbal IQ, convergent validity with a previous labelling task), reliability (Cronbach's alphas of.77 and.76 respectively), and wide individual differences across the typical population. We then demonstrate the usefulness of the tests by addressing theoretical questions regarding the structure of face processing, specifically the extent to which the following processes are common or distinct: (a) perceptual matching and explicit labelling of expression (modest correlation between matching and labelling supported partial independence); (b) judgement of expressions from faces and voices (results argued labelling tasks tap into a multi-modal system, while matching tasks tap distinct perceptual processes); and (c) expression and identity processing (results argued for a common first step of perceptual processing for expression and identity).

Development of the CROW{trademark} process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, L.A. Jr.

1994-05-01

The Contained Recovery of Oily Waste (CROW{trademark}) technology has been successfully tested in the laboratory and presently is being implemented at field sites contaminated with wood treating wastes and byproducts of town gas production. These field demonstrations will utilize only hot-water displacement without any chemical additives because the use of chemicals to enhance the hot-water flushing process has only been tested on a preliminary basis. Preliminary testing has shown that low concentrations of chemicals could reduce the contaminant content by an additional 10 to 20 wt %. Western Research Institute (WRI) research, plus research at Carnegie Mellon University, on surfactantmore » enhancement of solubility of polynuclear aromatic hydrocarbons in water and water-soil systems indicate the potential of chemical enhancement of the CROW process. Chemicals that have been tested and that were used in these tests are totally biodegradable. The objective of this task was to obtain sufficient baseline data to show the effectiveness and environmentally safe use of chemicals, primarily surfactants, to enhance the CROW process. To meet this objective, 14 one-dimensional displacement tests were conducted. Eleven tests were conducted on a material from a former manufactured gas plant (MGP) site and four tests were conducted with a contaminated soil from a former wood treatment facility. The tests investigated the effect of three chemical concentrations (0, 0.5, and 1.0 vol %) at three temperatures (ambient, the projected optimum temperature, and one 40{degree}F [22{degree}C] below the optimum temperature).« less

Joint EPA/NASA/USAF Interagency Depainting Study

NASA Technical Reports Server (NTRS)

Clark-Ingram, M.

2001-01-01

Environmental regulations such as National Emission Standards for Hazardous Air Pollutants (NESHAPs) are drivers for the implementation of environmentally compliant methodologies in the manufacture of aerospace hardware. In 1995, the Environmental Protection Agency (EPA) promulgated the NESHAP for the Aerospace Manufacture and Rework (Aerospace NESHAP) industry. Affected facilities were to be in compliance by September 1998. Several aerospace manufacturing operations are regulated within the Aerospace NESHAP including Depainting operations. The National Aeronautics and Space Administration (NASA), EPA, and United States Air Force (USAF) combined resources to evaluate the performance of nine alternative depainting processes. The seven alternative depainting processes were: (1) Chemical stripping (non-methylene chloride); (2) Carbon Dioxide Blasting; (3) Xenon Flashlamp; (4) Carbon Dioxide Laser Stripping; (5) Plastic Media Blasting; (6) Sodium Bicarbonate Wet Stripping; and (7) Waterjet Blasting and Wheat Starch Blasting. All epoxy primer and polyurethane top coat system was applied to 2024-T3 clad and non-clad aluminum test specimens. Approximately 200 test specimens were evaluated in this study. Each coupon was subjected to three, four, or five complete depainting cycles. This paper discusses the conclusions from the study including the test protocol, test parameters, and achievable strip rates for the alternative depainting processes. Test data includes immersion corrosion testing, sandwich corrosion testing and hydrogen embrittlement testing for the non-methylene chloride chemical strippers. Additionally, the cumulative effect of the alternative depainting processes on the metallurgical integrity of the test substrate is addressed with the results from tensile and fatigue evaluations.

Cryogenic Feedthrough Test Rig

NASA Technical Reports Server (NTRS)

Skaff, Antony

2009-01-01

The cryogenic feedthrough test rig (CFTR) allows testing of instrumentation feedthroughs at liquid oxygen and liquid hydrogen temperature and pressure extremes (dangerous process fluid) without actually exposing the feedthrough to a combustible or explosive process fluid. In addition, the helium used (inert gas), with cryogenic heat exchangers, exposes the feedthrough to that environment that allows definitive leak rates of feedthrough by typical industry-standard helium mass spectrometers.

Instructional Topics in Educational Measurement (ITEMS) Module: Using Automated Processes to Generate Test Items

ERIC Educational Resources Information Center

Gierl, Mark J.; Lai, Hollis

2013-01-01

Changes to the design and development of our educational assessments are resulting in the unprecedented demand for a large and continuous supply of content-specific test items. One way to address this growing demand is with automatic item generation (AIG). AIG is the process of using item models to generate test items with the aid of computer…

Spatial and Facial Processing in the Signed Discourse of Two Groups of Deaf Signers with Clinical Language Impairment

ERIC Educational Resources Information Center

Penn, Claire; Commerford, Ann; Ogilvy, Dale

2007-01-01

The linguistic and cognitive profiles of five deaf adults with a sign language disorder were compared with those of matched deaf controls. The test involved a battery of sign language tests, a signed narrative discourse task and a neuropsychological test protocol administered in sign language. Spatial syntax and facial processing were examined in…

Testing the Suitability of Mediation of Child Support Orders in Title IV-D Cases

ERIC Educational Resources Information Center

Schraufnagel, Scot; Li, Quan

2010-01-01

Objectives: The purpose of this study is to test mediation versus a traditional court process for the establishment or modification of child support orders. The intention is to determine which dispute resolution process is associated with greater client satisfaction and compliance. An auxiliary objective is to test the type of cases which are most…

Person Fit Based on Statistical Process Control in an Adaptive Testing Environment. Research Report 98-13.

ERIC Educational Resources Information Center

van Krimpen-Stoop, Edith M. L. A.; Meijer, Rob R.

Person-fit research in the context of paper-and-pencil tests is reviewed, and some specific problems regarding person fit in the context of computerized adaptive testing (CAT) are discussed. Some new methods are proposed to investigate person fit in a CAT environment. These statistics are based on Statistical Process Control (SPC) theory. A…

Effects of the Sense-Based Science Education Program on Scientific Process Skills of Children Aged 60-66 Months

ERIC Educational Resources Information Center

Tekerci, Hacer; Kandir, Adalet

2017-01-01

Purpose: This study aimed to examine the effects of the Sense-Based Science Education Program on 60-66 months old children's scientific process skills. Research Methods: In this study, which carries experimental attribute features, the pre-test/final-test/observing-test control grouped experimental pattern, and qualitative research were used.…

Psychological Reactance and Persuasive Health Communication: A Test and Extension of the Intertwined Model

ERIC Educational Resources Information Center

Rains, Stephen A.; Turner, Monique Mitchell

2007-01-01

This manuscript reports 2 experiments that were conducted to test and extend the work of J. P. Dillard and L. Shen (2005) examining the cognitive and affective processes involved in psychological reactance. In particular, the studies reported here (a) examined the best-fitting model of reactance processes and (b) tested 3 factors that may affect…

A Laminated Microfluidic Device for Comprehensive Preclinical Testing in the Drug ADME Process

PubMed Central

An, Fan; Qu, Yueyang; Luo, Yong; Fang, Ning; Liu, Yang; Gao, Zhigang; Zhao, Weijie; Lin, Bingcheng

2016-01-01

New techniques are urgently needed to replace conventional long and costly pre-clinical testing in the new drug administration process. In this study, a laminated microfluidic device was fabricated to mimic the drug ADME response test in vivo. This proposed device was loaded and cultured with functional cells for drug response investigation and organ tissues that are involved in ADME testing. The drug was introduced from the top of the device and first absorbed by the Caco-2 cell layer, and then metabolized by the primary hepatocyte layer. It subsequently interacted with the MCF-7 cell layer, distributed in the lung, heart and fat tissues, and was finally eliminated through the dialysis membrane. Throughout this on-chip ADME process, the proposed device can be used as a reliable tool to simultaneously evaluate the drug anti-tumor activity, hepatotoxicity and pharmacokinetics. Furthermore, this device was proven to be able to reflect the hepatic metabolism of a drug, drug distribution in the target tissues, and the administration method of a drug. Furthermore, this microdevice is expected to reduce the number of drug candidates and accelerate the pre-clinical testing process subject to animal testing upon adaptation in new drug discovery. PMID:27122192

Deficits in executive and memory processes in delusional disorder: a case-control study.

PubMed

Ibanez-Casas, Inmaculada; De Portugal, Enrique; Gonzalez, Nieves; McKenney, Kathryn A; Haro, Josep M; Usall, Judith; Perez-Garcia, Miguel; Cervilla, Jorge A

2013-01-01

Delusional disorder has been traditionally considered a psychotic syndrome that does not evolve to cognitive deterioration. However, to date, very little empirical research has been done to explore cognitive executive components and memory processes in Delusional Disorder patients. This study will investigate whether patients with delusional disorder are intact in both executive function components (such as flexibility, impulsivity and updating components) and memory processes (such as immediate, short term and long term recall, learning and recognition). A large sample of patients with delusional disorder (n = 86) and a group of healthy controls (n = 343) were compared with regard to their performance in a broad battery of neuropsychological tests including Trail Making Test, Wisconsin Card Sorting Test, Colour-Word Stroop Test, and Complutense Verbal Learning Test (TAVEC). When compared to controls, cases of delusional disorder showed a significantly poorer performance in most cognitive tests. Thus, we demonstrate deficits in flexibility, impulsivity and updating components of executive functions as well as in memory processes. These findings held significant after taking into account sex, age, educational level and premorbid IQ. Our results do not support the traditional notion of patients with delusional disorder being cognitively intact.

A Laminated Microfluidic Device for Comprehensive Preclinical Testing in the Drug ADME Process.

PubMed

An, Fan; Qu, Yueyang; Luo, Yong; Fang, Ning; Liu, Yang; Gao, Zhigang; Zhao, Weijie; Lin, Bingcheng

2016-04-28

New techniques are urgently needed to replace conventional long and costly pre-clinical testing in the new drug administration process. In this study, a laminated microfluidic device was fabricated to mimic the drug ADME response test in vivo. This proposed device was loaded and cultured with functional cells for drug response investigation and organ tissues that are involved in ADME testing. The drug was introduced from the top of the device and first absorbed by the Caco-2 cell layer, and then metabolized by the primary hepatocyte layer. It subsequently interacted with the MCF-7 cell layer, distributed in the lung, heart and fat tissues, and was finally eliminated through the dialysis membrane. Throughout this on-chip ADME process, the proposed device can be used as a reliable tool to simultaneously evaluate the drug anti-tumor activity, hepatotoxicity and pharmacokinetics. Furthermore, this device was proven to be able to reflect the hepatic metabolism of a drug, drug distribution in the target tissues, and the administration method of a drug. Furthermore, this microdevice is expected to reduce the number of drug candidates and accelerate the pre-clinical testing process subject to animal testing upon adaptation in new drug discovery.

High Vacuum Creep Facility in the Materials Processing Laboratory

NASA Image and Video Library

1973-01-21

Technicians at work in the Materials Processing Laboratory’s Creep Facility at the National Aeronautics and Space Administration (NASA) Lewis Research Center. The technicians supported the engineers’ studies of refractory materials, metals, and advanced superalloys. The Materials Processing Laboratory contained laboratories and test areas equipped to prepare and develop these metals and materials. The ultra-high vacuum lab, seen in this photograph, contained creep and tensile test equipment. Creep testing is used to study a material’s ability to withstand long durations under constant pressure and temperatures. The equipment measured the strain over a long period of time. Tensile test equipment subjects the test material to strain until the material fails. The two tests were used to determine the strength and durability of different materials. The Materials Processing Laboratory also housed arc and electron beam melting furnaces, a hydraulic vertical extrusion press, compaction and forging equipment, and rolling mills and swagers. There were cryogenic and gas storage facilities and mechanical and oil diffusion vacuum pumps. The facility contained both instrumental and analytical chemistry laboratories for work on radioactive or toxic materials and the only shop to machine toxic materials in the Midwest.

Experiments with Test Case Generation and Runtime Analysis

NASA Technical Reports Server (NTRS)

Artho, Cyrille; Drusinsky, Doron; Goldberg, Allen; Havelund, Klaus; Lowry, Mike; Pasareanu, Corina; Rosu, Grigore; Visser, Willem; Koga, Dennis (Technical Monitor)

2003-01-01

Software testing is typically an ad hoc process where human testers manually write many test inputs and expected test results, perhaps automating their execution in a regression suite. This process is cumbersome and costly. This paper reports preliminary results on an approach to further automate this process. The approach consists of combining automated test case generation based on systematically exploring the program's input domain, with runtime analysis, where execution traces are monitored and verified against temporal logic specifications, or analyzed using advanced algorithms for detecting concurrency errors such as data races and deadlocks. The approach suggests to generate specifications dynamically per input instance rather than statically once-and-for-all. The paper describes experiments with variants of this approach in the context of two examples, a planetary rover controller and a space craft fault protection system.

The design and application of virtual ion meter based on LABVIEW 8.0.

PubMed

Meng, Hu; Li, Jiangyuan; Tang, Yonghuai

2009-08-01

The virtual ion meter is developed based on LABVIEW 8.0 by homemade adjusting circuit, data acquisition (DAQ) board, and computer. This note provides details of the structure of testing system and flow chart of DAQ program. This virtual instrument system is applied to multitask testing such as determining rate constant of second-order reaction by pX, pX potentiometric titration, determining oscillating reaction by potential, etc. The result of application indicates that this test system not only has function of real-time data acquiring, displaying, storage, but also realizes remote monitoring and controlling test-control spots through internet, automatic analyzing and processing of data, reporting of result according to the different testing task; moreover, the veracity and repeatability of data processing result are higher than the results of manual data processing.

A Technique for Transient Thermal Testing of Thick Structures

NASA Technical Reports Server (NTRS)

Horn, Thomas J.; Richards, W. Lance; Gong, Leslie

1997-01-01

A new open-loop heat flux control technique has been developed to conduct transient thermal testing of thick, thermally-conductive aerospace structures. This technique uses calibration of the radiant heater system power level as a function of heat flux, predicted aerodynamic heat flux, and the properties of an instrumented test article. An iterative process was used to generate open-loop heater power profiles prior to each transient thermal test. Differences between the measured and predicted surface temperatures were used to refine the heater power level command profiles through the iteration process. This iteration process has reduced the effects of environmental and test system design factors, which are normally compensated for by closed-loop temperature control, to acceptable levels. The final revised heater power profiles resulted in measured temperature time histories which deviated less than 25 F from the predicted surface temperatures.

Item response theory scoring and the detection of curvilinear relationships.

PubMed

Carter, Nathan T; Dalal, Dev K; Guan, Li; LoPilato, Alexander C; Withrow, Scott A

2017-03-01

Psychologists are increasingly positing theories of behavior that suggest psychological constructs are curvilinearly related to outcomes. However, results from empirical tests for such curvilinear relations have been mixed. We propose that correctly identifying the response process underlying responses to measures is important for the accuracy of these tests. Indeed, past research has indicated that item responses to many self-report measures follow an ideal point response process-wherein respondents agree only to items that reflect their own standing on the measured variable-as opposed to a dominance process, wherein stronger agreement, regardless of item content, is always indicative of higher standing on the construct. We test whether item response theory (IRT) scoring appropriate for the underlying response process to self-report measures results in more accurate tests for curvilinearity. In 2 simulation studies, we show that, regardless of the underlying response process used to generate the data, using the traditional sum-score generally results in high Type 1 error rates or low power for detecting curvilinearity, depending on the distribution of item locations. With few exceptions, appropriate power and Type 1 error rates are achieved when dominance-based and ideal point-based IRT scoring are correctly used to score dominance and ideal point response data, respectively. We conclude that (a) researchers should be theory-guided when hypothesizing and testing for curvilinear relations; (b) correctly identifying whether responses follow an ideal point versus dominance process, particularly when items are not extreme is critical; and (c) IRT model-based scoring is crucial for accurate tests of curvilinearity. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nabeel A. Riza

The goals of the first six months of this project were to lay the foundations for both the SiC front-end optical chip fabrication as well as the free-space laser beam interferometer designs and preliminary tests. In addition, a Phase I goal was to design and experimentally build the high temperature and pressure infrastructure and test systems that will be used in the next 6 months for proposed sensor experimentation and data processing. All these goals have been achieved and are described in detail in the report. Both design process and diagrams for the mechanical elements as well as the opticalmore » systems are provided. In addition, photographs of the fabricated SiC optical chips, the high temperature & pressure test chamber instrument, the optical interferometer, the SiC sample chip holder, and signal processing data are provided. The design and experimentation results are summarized to give positive conclusions on the proposed novel high temperature optical sensor technology. The goals of the second six months of this project were to conduct high temperature sensing tests using the test chamber and optical sensing instrument designs developed in the first part of the project. In addition, a Phase I goal was to develop the basic processing theory and physics for the proposed first sensor experimentation and data processing. All these goals have been achieved and are described in detail. Both optical experimental design process and sensed temperature are provided. In addition, photographs of the fabricated SiC optical chips after deployment in the high temperature test chamber are shown from a material study point-of-view.« less

Effects of Cognitive Complexity and Emotional Upset on Processing Supportive Messages: Two Tests of a Dual-Process Theory of Supportive Communication Outcomes

ERIC Educational Resources Information Center

Bodie, Graham D.; Burleson, Brant R.; Holmstrom, Amanda J.; McCullough, Jennifer D.; Rack, Jessica J.; Hanasono, Lisa K.; Rosier, Jennifer G.

2011-01-01

We report tests of hypotheses derived from a theory of supportive communication outcomes that maintains the effects of supportive messages are moderated by factors influencing the motivation and ability to process these messages. Participants in two studies completed a measure of cognitive complexity, which provided an assessment of processing…

Testing Processability Theory in L2 Spanish: Can Readiness or Markedness Predict Development?

ERIC Educational Resources Information Center

Bonilla, Carrie L.

2012-01-01

The goal of this dissertation is to test the five stages of Processability Theory (PT) for second language (L2) learners of Spanish and investigate how instruction can facilitate the development through the stages. PT details five fixed stages in the acquisition of L2 morphosyntax based on principles of speech processing (Levelt, 1989) and modeled…

Industrial Tests to Modify Molten Copper Slag for Improvement of Copper Recovery

NASA Astrophysics Data System (ADS)

Guo, Zhengqi; Zhu, Deqing; Pan, Jian; Zhang, Feng; Yang, Congcong

2018-04-01

In this article, to improve the recovery of copper from copper slag by flotation process, industrial tests of the modification process involving addition of a composite additive into molten copper slag were conducted, and the modified slag was subjected to the flotation process to confirm the modification effect. The phase evolution of the slag in the modification process was revealed by thermodynamic calculations, x-ray diffraction, optical microscopy and scanning electron microscopy. The results show that more copper was transformed and enriched in copper sulfide phases. The magnetite content in the modified slag decreased, and that of "FeO" increased correspondingly, leading to a better fluidity of the molten slag, which improved the aggregation and growth of fine particles of the copper sulfide minerals. Closed-circuit flotation tests of the original and modified slags were conducted, and the results show that the copper recovery increased obviously from 69.15% to 73.38%, and the copper grade of concentrates was elevated slightly from 20.24% to 21.69%, further confirming that the industrial tests of the modification process were successful. Hence, the modification process has a bright future in industrial applications for enhancing the recovery of copper from the copper slag.

Development and pilot test of a process to identify research needs from a systematic review.

PubMed

Saldanha, Ian J; Wilson, Lisa M; Bennett, Wendy L; Nicholson, Wanda K; Robinson, Karen A

2013-05-01

To ensure appropriate allocation of research funds, we need methods for identifying high-priority research needs. We developed and pilot tested a process to identify needs for primary clinical research using a systematic review in gestational diabetes mellitus. We conducted eight steps: abstract research gaps from a systematic review using the Population, Intervention, Comparison, Outcomes, and Settings (PICOS) framework; solicit feedback from the review authors; translate gaps into researchable questions using the PICOS framework; solicit feedback from multidisciplinary stakeholders at our institution; establish consensus among multidisciplinary external stakeholders on the importance of the research questions using the Delphi method; prioritize outcomes; develop conceptual models to highlight research needs; and evaluate the process. We identified 19 research questions. During the Delphi method, external stakeholders established consensus for 16 of these 19 questions (15 with "high" and 1 with "medium" clinical benefit/importance). We pilot tested an eight-step process to identify clinically important research needs. Before wider application of this process, it should be tested using systematic reviews of other diseases. Further evaluation should include assessment of the usefulness of the research needs generated using this process for primary researchers and funders. Copyright © 2013 Elsevier Inc. All rights reserved.

Six Sigma methods applied to cryogenic coolers assembly line

NASA Astrophysics Data System (ADS)

Ventre, Jean-Marc; Germain-Lacour, Michel; Martin, Jean-Yves; Cauquil, Jean-Marc; Benschop, Tonny; Griot, René

2009-05-01

Six Sigma method have been applied to manufacturing process of a rotary Stirling cooler: RM2. Name of the project is NoVa as main goal of the Six Sigma approach is to reduce variability (No Variability). Project has been based on the DMAIC guideline following five stages: Define, Measure, Analyse, Improve, Control. Objective has been set on the rate of coolers succeeding performance at first attempt with a goal value of 95%. A team has been gathered involving people and skills acting on the RM2 manufacturing line. Measurement System Analysis (MSA) has been applied to test bench and results after R&R gage show that measurement is one of the root cause for variability in RM2 process. Two more root causes have been identified by the team after process mapping analysis: regenerator filling factor and cleaning procedure. Causes for measurement variability have been identified and eradicated as shown by new results from R&R gage. Experimental results show that regenerator filling factor impacts process variability and affects yield. Improved process haven been set after new calibration process for test bench, new filling procedure for regenerator and an additional cleaning stage have been implemented. The objective for 95% coolers succeeding performance test at first attempt has been reached and kept for a significant period. RM2 manufacturing process is now managed according to Statistical Process Control based on control charts. Improvement in process capability have enabled introduction of sample testing procedure before delivery.

Process Engineering Technology Center Initiative

NASA Technical Reports Server (NTRS)

Centeno, Martha A.

2001-01-01

NASA's Kennedy Space Center (KSC) is developing as a world-class Spaceport Technology Center (STC). From a process engineering (PE) perspective, the facilities used for flight hardware processing at KSC are NASA's premier factories. The products of these factories are safe, successful shuttle and expendable vehicle launches carrying state-of-the-art payloads. PE is devoted to process design, process management, and process improvement, rather than product design. PE also emphasizes the relationships of workers with systems and processes. Thus, it is difficult to speak of having a laboratory for PE at KSC because the entire facility is practically a laboratory when observed from a macro level perspective. However, it becomes necessary, at times, to show and display how KSC has benefited from PE and how KSC has contributed to the development of PE; hence, it has been proposed that a Process Engineering Technology Center (PETC) be developed to offer a place with a centralized focus on PE projects, and a place where KSC's PE capabilities can be showcased, and a venue where new Process Engineering technologies can be investigated and tested. Graphics for showcasing PE capabilities have been designed, and two initial test beds for PE technology research have been identified. Specifically, one test bed will look into the use of wearable computers with head mounted displays to deliver work instructions; the other test bed will look into developing simulation models that can be assembled into one to create a hierarchical model.

Process Engineering Technology Center Initiative

NASA Technical Reports Server (NTRS)

Centeno, Martha A.

2002-01-01

NASA's Kennedy Space Center (KSC) is developing as a world-class Spaceport Technology Center (STC). From a process engineering (PE) perspective, the facilities used for flight hardware processing at KSC are NASA's premier factories. The products of these factories are safe, successful shuttle and expendable vehicle launches carrying state-of-the-art payloads. PE is devoted to process design, process management, and process improvement, rather than product design. PE also emphasizes the relationships of workers with systems and processes. Thus, it is difficult to speak of having a laboratory for PE at K.S.C. because the entire facility is practically a laboratory when observed from a macro level perspective. However, it becomes necessary, at times, to show and display how K.S.C. has benefited from PE and how K.S.C. has contributed to the development of PE; hence, it has been proposed that a Process Engineering Technology Center (PETC) be developed to offer a place with a centralized focus on PE projects, and a place where K.S.C.'s PE capabilities can be showcased, and a venue where new Process Engineering technologies can be investigated and tested. Graphics for showcasing PE capabilities have been designed, and two initial test beds for PE technology research have been identified. Specifically, one test bed will look into the use of wearable computers with head mounted displays to deliver work instructions; the other test bed will look into developing simulation models that can be assembled into one to create a hierarchical model.

Mechanistic design data from ODOT instrumented pavement sites : phase II report.

DOT National Transportation Integrated Search

2017-03-01

This investigation examined data obtained from three previously-instrumented pavement test sites in Oregon. Data processing algorithms and templates were developed for each test site that facilitated full processing of all the data to build databases...

Mechanistic design data from ODOT instrumented pavement sites : phase 1 report.

DOT National Transportation Integrated Search

2017-03-01

This investigation examined data obtained from three previously-instrumented pavement test sites in Oregon. Data processing algorithms and templates were developed for each test site that facilitated full processing of all the data to build databases...

Field Testing of Cryogenic Carbon Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sayre, Aaron; Frankman, Dave; Baxter, Andrew

Sustainable Energy Solutions has been developing Cryogenic Carbon Capture™ (CCC) since 2008. In that time two processes have been developed, the External Cooling Loop and Compressed Flue Gas Cryogenic Carbon Capture processes (CCC ECL™ and CCC CFG™ respectively). The CCC ECL™ process has been scaled up to a 1TPD CO2 system. In this process the flue gas is cooled by an external refrigerant loop. SES has tested CCC ECL™ on real flue gas slip streams from subbituminous coal, bituminous coal, biomass, natural gas, shredded tires, and municipal waste fuels at field sites that include utility power stations, heating plants, cementmore » kilns, and pilot-scale research reactors. The CO2 concentrations from these tests ranged from 5 to 22% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2 and PMxx at 95+%. NO was also captured at a modest rate. The CCC CFG™ process has been scaled up to a .25 ton per day system. This system has been tested on real flue gas streams including subbituminous coal, bituminous coal and natural gas at field sites that include utility power stations, heating plants, and pilot-scale research reactors. CO2 concentrations for these tests ranged from 5 to 15% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2 and PMxx at 95+%. NO was also captured at 90+%. Hg capture was also verified and the resulting effluent from CCC CFG™ was below a 1ppt concentration. This paper will focus on discussion of the capabilities of CCC, the results of field testing and the future steps surrounding the development of this technology.« less

Effects on the efficiency of activated carbon on exposure to welding fumes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghosh, D.

1995-02-01

It is the intention of this paper to document that certain types of welding fumes have little or no effect on the effectiveness of the carbon filter air filtration efficiency when directly exposed to a controlled amount of welding fumes for a short-term period. The welding processes studied were restricted to shielded metal arc welding (SMAW), flux cored arc welding (FCAW), gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) processes. Contrary to the SMAW and FCAW processes, the GTAW (or TIG) and the GMAW (or MIG) welding processes do not require the use of flux as partmore » of the overall process. Credit was taken for these processes occurring in inert gas environments and producing minimal amount of smoke. It was concluded that a study involving the SMAW process would also envelop the effects of the TIG and MIG welding processes. The quantity of welding fumes generated during the arc welding process is a function of the particular process, the size and type of electrode, welding machine amperage, and operator proficiency. For this study, the amount of welding for specific testing was equated to the amount of welding normally conducted during plant unit outages. Different welding electrodes were also evaluated, and the subsequent testing was limited to an E7018 electrode which was judged to be representative of all carbon and stainless steel electrodes commonly used at the site. The effect of welding fumes on activated charcoal was tested using a filtration unit complete with prefilters, upstream and downstream high efficiency particulate air (HEPA) filters, and a carbon adsorber section. The complete system was field tested in accordance with ANSI N510 standards prior to exposing the filters and the adsorber bed to welding fumes. The carbon samples were tested at an established laboratory using ASTM D3803-1989 standards.« less

An Example for Integrated Gas Turbine Engine Testing and Analysis Using Modeling and Simulation

DTIC Science & Technology

2006-12-01

USAF Academy in a joint test and analysis effort of the F109 turbofan engine. This process uses a swirl investigation as a vehicle to exercise and...test and analysis effort of the F109 turbofan engine. This process uses a swirl investigation as a vehicle to exercise and demonstrate the approach...test and analysis effort of the F109 turbofan engine, an effort which uses a swirl investigation as a vehicle to exercise and demonstrate the

The Relationship between Types of Attention and Auditory Processing Skills: Reconsidering Auditory Processing Disorder Diagnosis

PubMed Central

Stavrinos, Georgios; Iliadou, Vassiliki-Maria; Edwards, Lindsey; Sirimanna, Tony; Bamiou, Doris-Eva

2018-01-01

Measures of attention have been found to correlate with specific auditory processing tests in samples of children suspected of Auditory Processing Disorder (APD), but these relationships have not been adequately investigated. Despite evidence linking auditory attention and deficits/symptoms of APD, measures of attention are not routinely used in APD diagnostic protocols. The aim of the study was to examine the relationship between auditory and visual attention tests and auditory processing tests in children with APD and to assess whether a proposed diagnostic protocol for APD, including measures of attention, could provide useful information for APD management. A pilot study including 27 children, aged 7–11 years, referred for APD assessment was conducted. The validated test of everyday attention for children, with visual and auditory attention tasks, the listening in spatialized noise sentences test, the children's communication checklist questionnaire and tests from a standard APD diagnostic test battery were administered. Pearson's partial correlation analysis examining the relationship between these tests and Cochrane's Q test analysis comparing proportions of diagnosis under each proposed battery were conducted. Divided auditory and divided auditory-visual attention strongly correlated with the dichotic digits test, r = 0.68, p < 0.05, and r = 0.76, p = 0.01, respectively, in a sample of 20 children with APD diagnosis. The standard APD battery identified a larger proportion of participants as having APD, than an attention battery identified as having Attention Deficits (ADs). The proposed APD battery excluding AD cases did not have a significantly different diagnosis proportion than the standard APD battery. Finally, the newly proposed diagnostic battery, identifying an inattentive subtype of APD, identified five children who would have otherwise been considered not having ADs. The findings show that a subgroup of children with APD demonstrates underlying sustained and divided attention deficits. Attention deficits in children with APD appear to be centred around the auditory modality but further examination of types of attention in both modalities is required. Revising diagnostic criteria to incorporate attention tests and the inattentive type of APD in the test battery, provides additional useful data to clinicians to ensure careful interpretation of APD assessments. PMID:29441033

The behavioural patterns and neural correlates of concrete and abstract verb processing in aphasia: A novel verb semantic battery.

PubMed

Alyahya, Reem S W; Halai, Ajay D; Conroy, Paul; Lambon Ralph, Matthew A

2018-01-01

Typically, processing is more accurate and efficient for concrete than abstract concepts in both healthy adults and individuals with aphasia. While, concreteness effects have been thoroughly documented with respect to noun processing, other words classes have received little attention despite tending to be less concrete than nouns. The aim of the current study was to explore concrete-abstract differences in verbs and identify their neural correlates in post-stroke aphasia. Given the dearth of comprehension tests for verbs, a battery of neuropsychological tests was developed in this study to assess the comprehension of concrete and abstract verbs. Specifically, a sensitive verb synonym judgment test was generated that varied both the items' imageability and frequency, and a picture-to-word matching test with numerous concrete verbs. Normative data were then collected and the tests were administered to a cohort of 48 individuals with chronic post-stroke aphasia to explore the behavioural patterns and neural correlates of verb processing. The results revealed significantly better comprehension of concrete than abstract verbs, aligning with the existing aphasiological literature on noun processing. In addition, the patients performed better during verb comprehension than verb production. Lesion-symptom correlational analyses revealed common areas that support processing of concrete and abstract verbs, including the left anterior temporal lobe, posterior supramarginal gyrus and superior lateral occipital cortex. A direct contrast between them revealed additional regions with graded differences. Specifically, the left frontal regions were associated with processing abstract verbs; whereas, the left posterior temporal and occipital regions were associated with processing concrete verbs. Moreover, overlapping and distinct neural correlates were identified in association with the comprehension and production of concrete verbs. These patient findings align with data from functional neuroimaging and neuro-stimulation, and existing models of language organisation.

Toward Higher QA: From Parametric Release of Sterile Parenteral Products to PAT for Other Pharmaceutical Dosage Forms.

PubMed

Hock, Sia Chong; Constance, Neo Xue Rui; Wah, Chan Lai

2012-01-01

Pharmaceutical products are generally subjected to end-product batch testing as a means of quality control. Due to the inherent limitations of conventional batch testing, this is not the most ideal approach for determining the pharmaceutical quality of the finished dosage form. In the case of terminally sterilized parenteral products, the limitations of conventional batch testing have been successfully addressed with the application of parametric release (the release of a product based on control of process parameters instead of batch sterility testing at the end of the manufacturing process). Consequently, there has been an increasing interest in applying parametric release to other pharmaceutical dosage forms, beyond terminally sterilized parenteral products. For parametric release to be possible, manufacturers must be capable of designing quality into the product, monitoring the manufacturing processes, and controlling the quality of intermediates and finished products in real-time. Process analytical technology (PAT) has been thought to be capable of contributing to these prerequisites. It is believed that the appropriate use of PAT tools can eventually lead to the possibility of real-time release of other pharmaceutical dosage forms, by-passing the need for end-product batch testing. Hence, this literature review attempts to present the basic principles of PAT, introduce the various PAT tools that are currently available, present their recent applications to pharmaceutical processing, and explain the potential benefits that PAT can bring to conventional ways of processing and quality assurance of pharmaceutical products. Last but not least, current regulations governing the use of PAT and the manufacturing challenges associated with PAT implementation are also discussed. Pharmaceutical products are generally subjected to end-product batch testing as a means of quality control. Due to the inherent limitations of conventional batch testing, this is not the most ideal approach. In the case of terminally sterilized parenteral products, these limitations have been successfully addressed with the application of parametric release (the release of a product based on control of process parameters instead of batch sterility testing at the end of the manufacturing process). Consequently, there has been an increasing interest in applying parametric release to other pharmaceutical dosage forms. With the advancement of process analytical technology (PAT), it is possible to monitor the manufacturing processes closely. This will eventually enable quality control of the intermediates and finished products, and thus their release in real-time. Hence, this literature review attempts to present the basic principles of PAT, introduce the various PAT tools that are currently available, present their recent applications to pharmaceutical processing, and explain the potential benefits that PAT can bring to conventional ways of processing and quality assurance of pharmaceutical products. It will also discuss the current regulations governing the use of PAT and the manufacturing challenges associated with the implementation of PAT.

Advances in Thin Film Thermocouple Durability Under High Temperature and Pressure Testing Conditions

NASA Technical Reports Server (NTRS)

Martin, Lisa C.; Fralick, Gustave C.; Taylor, Keith F.

1999-01-01

Thin film thermocouples for measuring material surface temperature have been previously demonstrated on several material systems and in various hostile test environments. A well-developed thin film fabrication procedure utilizing shadow masking for patterning the sensors elements had produced thin films with sufficient durability for applications in high temperature and pressure environments that exist in air-breathing and hydrogen-fueled burner rig and engine test facilities. However, while shadow masking had been a reliable method for specimens with flat and gently curved surfaces, it had not been consistently reliable for use on test components with sharp contours. This work reports on the feasibility of utilizing photolithography processing for patterning thin film thermocouples. Because this patterning process required changes in the thin film deposition process from that developed for shadow masking, the effect of these changes on thin film adherence during burner rig testing was evaluated. In addition to the results of changing the patterning method, the effects on thin film adherence of other processes used in the thin film fabrication procedure is also presented.

Review of Air Vitiation Effects on Scramjet Ignition and Flameholding Combustion Processes

NASA Technical Reports Server (NTRS)

Pellett, G. L.; Bruno, Claudio; Chinitz, W.

2002-01-01

This paper offers a detailed review and analysis of more than 100 papers on the physics and chemistry of scramjet ignition and flameholding combustion processes, and the known effects of air vitiation on these processes. The paper attempts to explain vitiation effects in terms of known chemical kinetics and flame propagation phenomena. Scaling methodology is also examined, and a highly simplified Damkoehler scaling technique based on OH radical production/destruction is developed to extrapolate ground test results, affected by vitiation, to flight testing conditions. The long term goal of this effort is to help provide effective means for extrapolating ground test data to flight, and thus to reduce the time and expense of both ground and flight testing.

Dynamic metrology and data processing for precision freeform optics fabrication and testing

NASA Astrophysics Data System (ADS)

Aftab, Maham; Trumper, Isaac; Huang, Lei; Choi, Heejoo; Zhao, Wenchuan; Graves, Logan; Oh, Chang Jin; Kim, Dae Wook

2017-06-01

Dynamic metrology holds the key to overcoming several challenging limitations of conventional optical metrology, especially with regards to precision freeform optical elements. We present two dynamic metrology systems: 1) adaptive interferometric null testing; and 2) instantaneous phase shifting deflectometry, along with an overview of a gradient data processing and surface reconstruction technique. The adaptive null testing method, utilizing a deformable mirror, adopts a stochastic parallel gradient descent search algorithm in order to dynamically create a null testing condition for unknown freeform optics. The single-shot deflectometry system implemented on an iPhone uses a multiplexed display pattern to enable dynamic measurements of time-varying optical components or optics in vibration. Experimental data, measurement accuracy / precision, and data processing algorithms are discussed.

The picture superiority effect in conceptual implicit memory: a conceptual distinctiveness hypothesis.

PubMed

Hamilton, Maryellen; Geraci, Lisa

2006-01-01

According to leading theories, the picture superiority effect is driven by conceptual processing, yet this effect has been difficult to obtain using conceptual implicit memory tests. We hypothesized that the picture superiority effect results from conceptual processing of a picture's distinctive features rather than a picture's semantic features. To test this hypothesis, we used 2 conceptual implicit general knowledge tests; one cued conceptually distinctive features (e.g., "What animal has large eyes?") and the other cued semantic features (e.g., "What animal is the figurehead of Tootsie Roll?"). Results showed a picture superiority effect only on the conceptual test using distinctive cues, supporting our hypothesis that this effect is mediated by conceptual processing of a picture's distinctive features.

Very high temperature fiber processing and testing through the use of ultrahigh solar energy concentration

NASA Astrophysics Data System (ADS)

Jacobson, Benjamin A.; Gleckman, Philip L.; Holman, Robert L.; Sagie, Daniel; Winston, Roland

1991-10-01

We have demonstrated the feasibility of a high temperature cool-wall optical furnace that harnesses the unique power of concentrated solar heating for advanced materials processing and testing. Out small-scale test furnace achieved temperatures as high as 2400 C within a 10 mm X 0.44 mm cylindrical hot-zone. Optimum performance and efficiency resulted from an innovative two-stage optical design using a long-focal length, point-focus, conventional primary concentrator and a non-imaging secondary concentrator specifically designed for the cylindrical geometry of the target fiber. A scale-up analysis suggests that even higher temperatures can be achieved over hot zones large enough for practical commercial fiber post- processing and testing.

KSC-2014-4133

NASA Image and Video Library

2014-09-25

CAPE CANAVERAL, Fla. – Operations are underway to couple Florida East Coast Railway, or FEC, locomotives No. 433 and No. 428 on the track alongside the Indian River, north of Launch Complex 39 at NASA’s Kennedy Space Center in Florida. Kennedy's Center Planning and Development Directorate has enlisted the locomotives to support a Rail Vibration Test for the Canaveral Port Authority. The purpose of the test is to collect amplitude, frequency and vibration test data utilizing two Florida East Coast locomotives operating on KSC tracks to ensure that future railroad operations will not affect launch vehicle processing at the center. Buildings instrumented for the test include the Rotation Processing Surge Facility, Thermal Protection Systems Facility, Vehicle Assembly Building, Orbiter Processing Facility and Booster Fabrication Facility. Photo credit: NASA/Daniel Casper

KSC-2014-4140

NASA Image and Video Library

2014-09-25

CAPE CANAVERAL, Fla. – Coupled Florida East Coast Railway, or FEC, locomotives No. 433 and No. 428 pass the Vehicle Assembly Building in Launch Complex 39 at NASA’s Kennedy Space Center in Florida on their way to NASA's Locomotive Maintenance Facility. Kennedy's Center Planning and Development Directorate has enlisted the locomotives to support a Rail Vibration Test for the Canaveral Port Authority. The purpose of the test is to collect amplitude, frequency and vibration test data utilizing two Florida East Coast locomotives operating on KSC tracks to ensure that future railroad operations will not affect launch vehicle processing at the center. Buildings instrumented for the test include the Rotation Processing Surge Facility, Thermal Protection Systems Facility, Vehicle Assembly Building, Orbiter Processing Facility and Booster Fabrication Facility. Photo credit: NASA/Daniel Casper

Galnon Facilitates Extinction of Morphine-Conditioned Place Preference but Also Potentiates the Consolidation Process

PubMed Central

Zhao, Xiaojie; Yun, Keming; Seese, Ronald R.; Wang, Zhenyuan

2013-01-01

Learning and memory systems are intimately involved in drug addiction. Previous studies suggest that galanin, a neuropeptide that binds G-protein coupled receptors, plays essential roles in the encoding of memory. In the present study, we tested the function of galnon, a galanin receptor 1 and 2 agonist, in reward-associated memory, using conditioned place preference (CPP), a widely used paradigm in drug-associated memory. Either before or following CPP-inducing morphine administration, galnon was injected at four different time points to test the effects of galanin activation on different reward-associated memory processes: 15 min before CPP training (acquisition), immediately after CPP training (consolidation), 15 min before the post-conditioning test (retrieval), and multiple injection after post-tests (reconsolidation and extinction). Galnon enhanced consolidation and extinction processes of morphine-induced CPP memory, but the compound had no effect on acquisition, retrieval, or reconsolidation processes. Our findings demonstrate that a galanin receptor 1 and 2 agonist, galnon, may be used as a viable compound to treat drug addiction by facilitating memory extinction process. PMID:24146862

Galnon facilitates extinction of morphine-conditioned place preference but also potentiates the consolidation process.

PubMed

Zhao, Xiaojie; Yun, Keming; Seese, Ronald R; Wang, Zhenyuan

2013-01-01

Learning and memory systems are intimately involved in drug addiction. Previous studies suggest that galanin, a neuropeptide that binds G-protein coupled receptors, plays essential roles in the encoding of memory. In the present study, we tested the function of galnon, a galanin receptor 1 and 2 agonist, in reward-associated memory, using conditioned place preference (CPP), a widely used paradigm in drug-associated memory. Either before or following CPP-inducing morphine administration, galnon was injected at four different time points to test the effects of galanin activation on different reward-associated memory processes: 15 min before CPP training (acquisition), immediately after CPP training (consolidation), 15 min before the post-conditioning test (retrieval), and multiple injection after post-tests (reconsolidation and extinction). Galnon enhanced consolidation and extinction processes of morphine-induced CPP memory, but the compound had no effect on acquisition, retrieval, or reconsolidation processes. Our findings demonstrate that a galanin receptor 1 and 2 agonist, galnon, may be used as a viable compound to treat drug addiction by facilitating memory extinction process.

Investigation of Conditions of Titanium Carbonization - IV

NASA Technical Reports Server (NTRS)

Meerson, G. A.; Lipkes, Y. M.

1949-01-01

In a previous paper, results are presented of accurate investigations of the processes of titanium carbonization and the succeeding titanium carbide decarbonization as related to the phenomenon of the graphitization of soot by heating at a constant temperature in atmospheres of pure hydrogen and carbon monoxide. These tests showed that the processes of titanium carbonization-decarbonization in an atmosphere of pure gases without nitrogen proceed in the same direction as the analogous processes under the conditions of the production furnace. In this case, however, the presence of admixtures of nitrogen changes the quantitative results of the decarbonization process. Thermodynamic computations confirming the results of previous tests conducted at atmospheric pressure and additional tests of titanium carbonization at lowered pressures are presented herein.

Framework for managing mycotoxin risks in the food industry.

PubMed

Baker, Robert C; Ford, Randall M; Helander, Mary E; Marecki, Janusz; Natarajan, Ramesh; Ray, Bonnie

2014-12-01

We propose a methodological framework for managing mycotoxin risks in the food processing industry. Mycotoxin contamination is a well-known threat to public health that has economic significance for the food processing industry; it is imperative to address mycotoxin risks holistically, at all points in the procurement, processing, and distribution pipeline, by tracking the relevant data, adopting best practices, and providing suitable adaptive controls. The proposed framework includes (i) an information and data repository, (ii) a collaborative infrastructure with analysis and simulation tools, (iii) standardized testing and acceptance sampling procedures, and (iv) processes that link the risk assessments and testing results to the sourcing, production, and product release steps. The implementation of suitable acceptance sampling protocols for mycotoxin testing is considered in some detail.

Assembly processes comparison for a miniaturized laser used for the Exomars European Space Agency mission

NASA Astrophysics Data System (ADS)

Ribes-Pleguezuelo, Pol; Inza, Andoni Moral; Basset, Marta Gilaberte; Rodríguez, Pablo; Rodríguez, Gemma; Laudisio, Marco; Galan, Miguel; Hornaff, Marcel; Beckert, Erik; Eberhardt, Ramona; Tünnermann, Andreas

2016-11-01

A miniaturized diode-pumped solid-state laser (DPSSL) designed as part of the Raman laser spectrometer (RLS) instrument for the European Space Agency (ESA) Exomars mission 2020 is assembled and tested for the mission purpose and requirements. Two different processes were tried for the laser assembling: one based on adhesives, following traditional laser manufacturing processes; another based on a low-stress and organic-free soldering technique called solderjet bumping technology. The manufactured devices were tested for the processes validation by passing mechanical, thermal cycles, radiation, and optical functional tests. The comparison analysis showed a device improvement in terms of reliability of the optical performances from the soldered to the assembled by adhesive-based means.

Investigation of hazards associated with plastic bonded starter mix manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

An investigation to determine the hazards potential evaluation of plastic bonded starter mix (PBSM) production processes and the application to the M18 and M7A3 grenades is reported. The investigation indicated: (1) the materials with the greatest hazards characteristics, (2) process operating stations most likely to initiate hazardous conditions, (3) the test program required to examine ignition characteristics and process hazards, and (4) the method of handling the accumulated information from testing and safety analyses.

Strategy Choice Mediates the Link between Auditory Processing and Spelling

PubMed Central

Kwong, Tru E.; Brachman, Kyle J.

2014-01-01

Relations among linguistic auditory processing, nonlinguistic auditory processing, spelling ability, and spelling strategy choice were examined. Sixty-three undergraduate students completed measures of auditory processing (one involving distinguishing similar tones, one involving distinguishing similar phonemes, and one involving selecting appropriate spellings for individual phonemes). Participants also completed a modified version of a standardized spelling test, and a secondary spelling test with retrospective strategy reports. Once testing was completed, participants were divided into phonological versus nonphonological spellers on the basis of the number of words they spelled using phonological strategies only. Results indicated a) moderate to strong positive correlations among the different auditory processing tasks in terms of reaction time, but not accuracy levels, and b) weak to moderate positive correlations between measures of linguistic auditory processing (phoneme distinction and phoneme spelling choice in the presence of foils) and spelling ability for phonological spellers, but not for nonphonological spellers. These results suggest a possible explanation for past contradictory research on auditory processing and spelling, which has been divided in terms of whether or not disabled spellers seemed to have poorer auditory processing than did typically developing spellers, and suggest implications for teaching spelling to children with good versus poor auditory processing abilities. PMID:25198787

Similarities and Differences Between Working Memory and Long-Term Memory: Evidence From the Levels-of-Processing Span Task

PubMed Central

Rose, Nathan S.; Myerson, Joel; Roediger, Henry L.; Hale, Sandra

2010-01-01

Two experiments compared the effects of depth of processing on working memory (WM) and long-term memory (LTM) using a levels-of-processing (LOP) span task, a newly developed WM span procedure that involves processing to-be-remembered words based on their visual, phonological, or semantic characteristics. Depth of processing had minimal effect on WM tests, yet subsequent memory for the same items on delayed tests showed the typical benefits of semantic processing. Although the difference in LOP effects demonstrates a dissociation between WM and LTM, we also found that the retrieval practice provided by recalling words on the WM task benefited long-term retention, especially for words initially recalled from supraspan lists. The latter result is consistent with the hypothesis that WM span tasks involve retrieval from secondary memory, but the LOP dissociation suggests the processes engaged by WM and LTM tests may differ. Therefore, similarities and differences between WM and LTM depend on the extent to which retrieval from secondary memory is involved and whether there is a match (or mismatch) between initial processing and subsequent retrieval, consistent with transfer-appropriate-processing theory. PMID:20192543

Strategy choice mediates the link between auditory processing and spelling.

PubMed

Kwong, Tru E; Brachman, Kyle J

2014-01-01

Relations among linguistic auditory processing, nonlinguistic auditory processing, spelling ability, and spelling strategy choice were examined. Sixty-three undergraduate students completed measures of auditory processing (one involving distinguishing similar tones, one involving distinguishing similar phonemes, and one involving selecting appropriate spellings for individual phonemes). Participants also completed a modified version of a standardized spelling test, and a secondary spelling test with retrospective strategy reports. Once testing was completed, participants were divided into phonological versus nonphonological spellers on the basis of the number of words they spelled using phonological strategies only. Results indicated a) moderate to strong positive correlations among the different auditory processing tasks in terms of reaction time, but not accuracy levels, and b) weak to moderate positive correlations between measures of linguistic auditory processing (phoneme distinction and phoneme spelling choice in the presence of foils) and spelling ability for phonological spellers, but not for nonphonological spellers. These results suggest a possible explanation for past contradictory research on auditory processing and spelling, which has been divided in terms of whether or not disabled spellers seemed to have poorer auditory processing than did typically developing spellers, and suggest implications for teaching spelling to children with good versus poor auditory processing abilities.

Successful MPPF Pneumatics Verification and Validation Testing

NASA Image and Video Library

2017-03-28

Engineers and technicians completed verification and validation testing of several pneumatic systems inside and outside the Multi-Payload Processing Facility (MPPF) at NASA's Kennedy Space Center in Florida. In view is the service platform for Orion spacecraft processing. To the left are several pneumatic panels. The MPPF will be used for offline processing and fueling of the Orion spacecraft and service module stack before launch. Orion also will be de-serviced in the MPPF after a mission. The Ground Systems Development and Operations Program (GSDO) is overseeing upgrades to the facility. The Engineering Directorate led the recent pneumatic tests.

Modernization of the Transonic Axial Compressor Test Rig

DTIC Science & Technology

2017-12-01

13. ABSTRACT (maximum 200 words) This work presents the design and simulation process of modernizing the Naval Postgraduate School’s transonic...fabricate the materials. Stiffness tests and modal analysis were conducted via Finite Element Analysis (FEA) software. This analysis was used to design ...work presents the design and simulation process of modernizing the Naval Postgraduate School’s transonic compressor test rig (TCR). The TCR, which

Testing of a Microfluidic Sampling System for High Temperature Electrochemical MC&A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pereira, Candido; Nichols, Kevin

2013-11-27

This report describes the preliminary validation of a high-temperature microfluidic chip system for sampling of electrochemical process salt. Electroanalytical and spectroscopic techniques are attractive candidates for improvement through high-throughput sample analysis via miniaturization. Further, microfluidic chip systems are amenable to micro-scale chemical processing such as rapid, automated sample purification to improve sensor performance. The microfluidic chip was tested to determine the feasibility of the system for high temperature applications and conditions under which microfluidic systems can be used to generate salt droplets at process temperature to support development of material balance and control systems in a used fuel treatment facility.more » In FY13, the project focused on testing a quartz microchip device with molten salts at near process temperatures. The equipment was installed in glove box and tested up to 400°C using commercial thermal transfer fluids as the carrier phase. Preliminary tests were carried out with a low-melting halide salt to initially characterize the properties of this novel liquid-liquid system and to investigate the operating regimes for inducing droplet flow within candidate carrier fluids. Initial results show that the concept is viable for high temperature sampling but further development is required to optimize the system to operate with process relevant molten salts.« less

Process capability determination of new and existing equipment

NASA Technical Reports Server (NTRS)

Mcclelland, H. T.; Su, Penwen

1994-01-01

The objective of this paper is to illustrate a method of determining the process capability of new or existing equipment. The method may also be modified to apply to testing laboratories. Long term changes in the system may be determined by periodically making new test parts or submitting samples from the original set to the testing laboratory. The technique described has been developed through a series of projects in special topics manufacturing courses and graduate student projects. It will be implemented as a standard experiment in an advanced manufacturing course in a new Manufacturing Engineering program at the University of Wisconsin-Stout campus. Before starting a project of this nature, it is important to decide on the exact question to be answered. In this case, it is desired to know what variation can be reasonably expected in the next part, feature, or test result produced. Generally, this question is answered by providing the process capability or the average value of a measured characteristic of the part or process plus or minus three standard deviations. There are two general cases to be considered: the part or test is made in large quantities with little change, or the process is flexible and makes a large variety of parts. Both cases can be accommodated; however, the emphasis in this report is on short run situations.

Experiments for practical education in process parameter optimization for selective laser sintering to increase workpiece quality

NASA Astrophysics Data System (ADS)

Reutterer, Bernd; Traxler, Lukas; Bayer, Natascha; Drauschke, Andreas

2016-04-01

Selective Laser Sintering (SLS) is considered as one of the most important additive manufacturing processes due to component stability and its broad range of usable materials. However the influence of the different process parameters on mechanical workpiece properties is still poorly studied, leading to the fact that further optimization is necessary to increase workpiece quality. In order to investigate the impact of various process parameters, laboratory experiments are implemented to improve the understanding of the SLS limitations and advantages on an educational level. Experiments are based on two different workstations, used to teach students the fundamentals of SLS. First of all a 50 W CO2 laser workstation is used to investigate the interaction of the laser beam with the used material in accordance with varied process parameters to analyze a single-layered test piece. Second of all the FORMIGA P110 laser sintering system from EOS is used to print different 3D test pieces in dependence on various process parameters. Finally quality attributes are tested including warpage, dimension accuracy or tensile strength. For dimension measurements and evaluation of the surface structure a telecentric lens in combination with a camera is used. A tensile test machine allows testing of the tensile strength and the interpreting of stress-strain curves. The developed laboratory experiments are suitable to teach students the influence of processing parameters. In this context they will be able to optimize the input parameters depending on the component which has to be manufactured and to increase the overall quality of the final workpiece.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. Test article, a 3.35m long with the diameter of 20 cm incline line, was filled with liquid (LH2)or gaseous hydrogen (GH2) and then purged with gaseous helium (GHe). Total of 10 tests were conducted. Influences of GHe flow rates and initial temperatures were evaluated. Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer, was utilized to model and simulate selective tests.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The NOXSO Process uses a regenerable sorbent that removes SO{sub 2} and NO{sub x} simultaneously from flue gas. The sorbent is a stabilized {gamma}-alumina bed impregnated with sodium carbonate. The process was successfully tested at three different scales, equivalent to 0.017, 0.06 and 0.75 MW of flue gas generated from a coal-fired power plant. The Proof-of-Concept (POC) Test is the last test prior to a full-scale demonstration. A slip stream of flue gas equivalent to a 5 MW coal-fired power plant was used for the POC test. This paper summarizes the NOXSO POC plant and its test results.

Final Report - Melt Rate Enhancement for High Aluminum HLW Glass Formulation, VSL-08R1360-1, Rev. 0, dated 12/19/08

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, Albert A.; Pegg, I. L.; Chaudhuri, M.

2013-11-13

The principal objective of the work reported here was to develop and identify HLW glass compositions that maximize waste processing rates for the aluminum limted waste composition specified by ORP while maintaining high waste loadings and acceptable glass properties. This was accomplished through a combination of crucible-scale tests, confirmation tests on the DM100 melter system, and demonstration at pilot scale (DM1200). The DM100-BL unit was selected for these tests since it was used previously with the HLW waste streams evaluated in this study, was used for tests on HLW glass compositions to support subsequent tests on the HLW Pilot Melter,more » conduct tests to determine the effect of various glass properties (viscosity and conductivity) and oxide concentrations on glass production rates with HLW feed streams, and to assess the volatility of cesium and technetium during the vitrification of an HLW AZ-102 composition. The same melter was selected for the present tests in order to maintain comparisons between the previously collected data. These tests provide information on melter processing characteristics and off-gas data, including formation of secondary phases and partitioning. Once DM100 tests were completed, one of the compositions was selected for further testing on the DM1200; the DM1200 system has been used for processing a variety of simulated Hanford waste streams. Tests on the larger melter provide processing data at one third of the scale of the actual WTP HLW melter and, therefore, provide a more accurate and reliable assessment of production rates and potential processing issues. The work focused on maximizing waste processing rates for high aluminum HLW compositions. In view of the diversity of forms of aluminum in the Hanford tanks, tests were also conducted on the DM100 to determine the effect of changes in the form of aluminum on feed properties and production rate. In addition, the work evaluated the effect on production rate of modest increases in melter operating temperature. Glass composition development was based on one of the HLW waste compositions specified by ORP that has a high concentration of aluminum. Small-scale tests were used to provide an initial screening of various glass formulations with respect to melt rates; more definitive screening was provided by the subsequent DM100 tests. Glass properties evaluated included: viscosity, electrical conductivity, crystallinity, gross glass phase separation and the 7- day Product Consistency Test (ASTM-1285). Glass property limits were based upon the reference properties for the WTP HLW melter. However, the WTP crystallinity limit (< 1 vol% at 950oC) was relaxed slightly as a waste loading constraint for the crucible melts.« less

Reliability and validity of the revised Gibson Test of Cognitive Skills, a computer-based test battery for assessing cognition across the lifespan.

PubMed

Moore, Amy Lawson; Miller, Terissa M

2018-01-01

The purpose of the current study is to evaluate the validity and reliability of the revised Gibson Test of Cognitive Skills, a computer-based battery of tests measuring short-term memory, long-term memory, processing speed, logic and reasoning, visual processing, as well as auditory processing and word attack skills. This study included 2,737 participants aged 5-85 years. A series of studies was conducted to examine the validity and reliability using the test performance of the entire norming group and several subgroups. The evaluation of the technical properties of the test battery included content validation by subject matter experts, item analysis and coefficient alpha, test-retest reliability, split-half reliability, and analysis of concurrent validity with the Woodcock Johnson III Tests of Cognitive Abilities and Tests of Achievement. Results indicated strong sources of evidence of validity and reliability for the test, including internal consistency reliability coefficients ranging from 0.87 to 0.98, test-retest reliability coefficients ranging from 0.69 to 0.91, split-half reliability coefficients ranging from 0.87 to 0.91, and concurrent validity coefficients ranging from 0.53 to 0.93. The Gibson Test of Cognitive Skills-2 is a reliable and valid tool for assessing cognition in the general population across the lifespan.

Hanford Low-Activity Waste Processing: Demonstration of the Off-Gas Recycle Flowsheet - 13443

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramsey, William G.; Esparza, Brian P.

2013-07-01

Vitrification of Hanford Low-Activity Waste (LAW) is nominally the thermal conversion and incorporation of sodium salts and radionuclides into borosilicate glass. One key radionuclide present in LAW is technetium-99. Technetium-99 is a low energy, long-lived beta emitting radionuclide present in the waste feed in concentrations on the order of 1-10 ppm. The long half-life combined with a high solubility in groundwater results in technetium-99 having considerable impact on performance modeling (as potential release to the environment) of both the waste glass and associated secondary waste products. The current Hanford Tank Waste Treatment and Immobilization Plant (WTP) process flowsheet calls formore » the recycle of vitrification process off-gas condensates to maximize the portion of technetium ultimately immobilized in the waste glass. This is required as technetium acts as a semi-volatile specie, i.e. considerable loss of the radionuclide to the process off-gas stream can occur during the vitrification process. To test the process flowsheet assumptions, a prototypic off-gas system with recycle capability was added to a laboratory melter (on the order of 1/200 scale) and testing performed. Key test goals included determination of the process mass balance for technetium, a non-radioactive surrogate (rhenium), and other soluble species (sulfate, halides, etc.) which are concentrated by recycling off-gas condensates. The studies performed are the initial demonstrations of process recycle for this type of liquid-fed melter system. This paper describes the process recycle system, the waste feeds processed, and experimental results. Comparisons between data gathered using process recycle and previous single pass melter testing as well as mathematical modeling simulations are also provided. (authors)« less

Laser Processed Heat Exchangers

NASA Technical Reports Server (NTRS)

Hansen, Scott

2017-01-01

The Laser Processed Heat Exchanger project will investigate the use of laser processed surfaces to reduce mass and volume in liquid/liquid heat exchangers as well as the replacement of the harmful and problematic coatings of the Condensing Heat Exchangers (CHX). For this project, two scale unit test articles will be designed, manufactured, and tested. These two units are a high efficiency liquid/liquid HX and a high reliability CHX.

Data reduction complex analog-to-digital data processing requirements for onsite test facilities

NASA Technical Reports Server (NTRS)

Debbrecht, J. D.

1976-01-01

The analog to digital processing requirements of onsite test facilities are described. The source and medium of all input data to the Data Reduction Complex (DRC) and the destination and medium of all output products of the analog-to-digital processing are identified. Additionally, preliminary input and output data formats are presented along with the planned use of the output products.

Real-time flight test data distribution and display

NASA Technical Reports Server (NTRS)

Nesel, Michael C.; Hammons, Kevin R.

1988-01-01

Enhancements to the real-time processing and display systems of the NASA Western Aeronautical Test Range are described. Display processing has been moved out of the telemetry and radar acquisition processing systems super-minicomputers into user/client interactive graphic workstations. Real-time data is provided to the workstations by way of Ethernet. Future enhancement plans include use of fiber optic cable to replace the Ethernet.

Ranking protective coatings: Laboratory vs. field experience

NASA Astrophysics Data System (ADS)

Conner, Jeffrey A.; Connor, William B.

1994-12-01

Environmentally protective coatings are used on a wide range of gas turbine components for survival in the harsh operating conditions of engines. A host of coatings are commercially available to protect hot-section components, ranging from simple aluminides to designer metallic overlays and ceramic thermal barrier coatings. A variety of coating-application processes are available, and they range from simple pack cementation processing to complex physical vapor deposition, which requires multimillion dollar facilities. Detailed databases are available for most coatings and coating/process combinations for a range of laboratory tests. Still, the analysis of components actually used in engines often yields surprises when compared against predicted coating behavior from laboratory testing. This paper highlights recent work to develop new laboratory tests that better simulate engine environments. Comparison of in-flight coating performance as well as industrial and factory engine testing on a range of hardware is presented along with laboratory predictions from standard testing and from recently developed cyclic burner-rig testing.

Plan for Quality to Improve Patient Safety at the Point of Care

PubMed Central

Ehrmeyer, Sharon S.

2011-01-01

The U.S. Institute of Medicine (IOM) much publicized report in “To Err is Human” (2000, National Academy Press) stated that as many as 98 000 hospitalized patients in the U.S. die each year due to preventable medical errors. This revelation about medical error and patient safety focused the public and the medical community's attention on errors in healthcare delivery including laboratory and point-of-care-testing (POCT). Errors introduced anywhere in the POCT process clearly can impact quality and place patient's safety at risk. While POCT performed by or near the patient reduces the potential of some errors, the process presents many challenges to quality with its multiple tests sites, test menus, testing devices and non-laboratory analysts, who often have little understanding of quality testing. Incoherent or no regulations and the rapid availability of test results for immediate clinical intervention can further amplify errors. System planning and management of the entire POCT process are essential to reduce errors and improve quality and patient safety. PMID:21808107

Input-output characterization of an ultrasonic testing system by digital signal analysis

NASA Technical Reports Server (NTRS)

Karaguelle, H.; Lee, S. S.; Williams, J., Jr.

1984-01-01

The input/output characteristics of an ultrasonic testing system used for stress wave factor measurements were studied. The fundamentals of digital signal processing are summarized. The inputs and outputs are digitized and processed in a microcomputer using digital signal processing techniques. The entire ultrasonic test system, including transducers and all electronic components, is modeled as a discrete-time linear shift-invariant system. Then the impulse response and frequency response of the continuous time ultrasonic test system are estimated by interpolating the defining points in the unit sample response and frequency response of the discrete time system. It is found that the ultrasonic test system behaves as a linear phase bandpass filter. Good results were obtained for rectangular pulse inputs of various amplitudes and durations and for tone burst inputs whose center frequencies are within the passband of the test system and for single cycle inputs of various amplitudes. The input/output limits on the linearity of the system are determined.

Assessment of DPOAE test-retest difference curves via hierarchical Gaussian processes.

PubMed

Bao, Junshu; Hanson, Timothy; McMillan, Garnett P; Knight, Kristin

2017-03-01

Distortion product otoacoustic emissions (DPOAE) testing is a promising alternative to behavioral hearing tests and auditory brainstem response testing of pediatric cancer patients. The central goal of this study is to assess whether significant changes in the DPOAE frequency/emissions curve (DP-gram) occur in pediatric patients in a test-retest scenario. This is accomplished through the construction of normal reference charts, or credible regions, that DP-gram differences lie in, as well as contour probabilities that measure how abnormal (or in a certain sense rare) a test-retest difference is. A challenge is that the data were collected over varying frequencies, at different time points from baseline, and on possibly one or both ears. A hierarchical structural equation Gaussian process model is proposed to handle the different sources of correlation in the emissions measurements, wherein both subject-specific random effects and variance components governing the smoothness and variability of each child's Gaussian process are coupled together. © 2016, The International Biometric Society.

Test Report for Permanganate and Cold Strontium Strike for Tank 241-AN-102

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duncan, James B.; Huber, Heinz J.; Smalley, Colleen S.

Tanks 241-AN-102 and 241-AN-107 supernatants contain soluble Sr-90 and transuranic elements that require removal prior to vitrification to comply with the Waste Treatment and Immobilization Plant immobilized low-activity waste specification (WTP Contract, DE-AC27-01RV 14136, Specification 2.2.2.8, "Radionuclide Concentration Limitations") and the U.S. Nuclear Regulatory Commission provisional agreement on waste incidental to reprocessing (letter, Paperiello, C. J., "Classification of Hanford Low-Activity Tank Waste Fraction"). These two tanks have high concentrations of organics and organic complexants and are referred to as complexant concentrate tanks. A precipitation process using sodium permanganate (NaMnO{sub 4}) and strontium nitrate (Sr(NO{sub 3}){sub 2}) was developed and testedmore » with tank waste samples to precipitate Sr-90 and transuranic elements from the supernate (PNWD-3141, Optimization of Sr/TRU Removal Conditions with Samples of AN-102 Tank Waste). Testing documented in this report was conducted to further evaluate the use of the strontium nitrate/sodium permanganate process in tank farms with a retention time of up to 12 months. Previous testing was focused on developing a process for deployment in the ultrafiltration vessels in the Waste Treatment and Immobilization Plant. This environment is different from tank farms in two important ways: the waste is diluted in the Waste Treatment and Immobilization Plant to ~5.5 M sodium, whereas the supernate in the tank farms is ~9 M Na. Secondly, while the Waste Treatment and Immobilization Plant allows for a maximum treatment time of hours to days, the in-tank farms treatment of tanks 241-AN102 and 241-AN-107 will result in a retention time of months (perhaps up to12 months) before processing. A comparative compilation of separation processes for Sr/transuranics has been published as RPP-RPT-48340, Evaluation of Alternative Strontium and Transuranic Separation Processes. This report also listed the testing needs for the permanganate precipitation process to be field-deployable. A more comprehensive listing of future testing needs to allow the process to be field deployable are contained in RPP-PLAN-51288, Development Test Plan for Sr/TRU Precipitation Process.« less

Mechanical Design of a Performance Test Rig for the Turbine Air-Flow Task (TAFT)

NASA Technical Reports Server (NTRS)

Forbes, John C.; Xenofos, George D.; Farrow, John L.; Tyler, Tom; Williams, Robert; Sargent, Scott; Moharos, Jozsef

2004-01-01

To support development of the Boeing-Rocketdyne RS84 rocket engine, a full-flow, reaction turbine geometry was integrated into the NASA-MSFC turbine air-flow test facility. A mechanical design was generated which minimized the amount of new hardware while incorporating all test and instrumentation requirements. This paper provides details of the mechanical design for this Turbine Air-Flow Task (TAFT) test rig. The mechanical design process utilized for this task included the following basic stages: Conceptual Design. Preliminary Design. Detailed Design. Baseline of Design (including Configuration Control and Drawing Revision). Fabrication. Assembly. During the design process, many lessons were learned that should benefit future test rig design projects. Of primary importance are well-defined requirements early in the design process, a thorough detailed design package, and effective communication with both the customer and the fabrication contractors.

Reliability growth modeling analysis of the space shuttle main engines based upon the Weibull process

NASA Technical Reports Server (NTRS)

Wheeler, J. T.

1990-01-01

The Weibull process, identified as the inhomogeneous Poisson process with the Weibull intensity function, is used to model the reliability growth assessment of the space shuttle main engine test and flight failure data. Additional tables of percentage-point probabilities for several different values of the confidence coefficient have been generated for setting (1-alpha)100-percent two sided confidence interval estimates on the mean time between failures. The tabled data pertain to two cases: (1) time-terminated testing, and (2) failure-terminated testing. The critical values of the three test statistics, namely Cramer-von Mises, Kolmogorov-Smirnov, and chi-square, were calculated and tabled for use in the goodness of fit tests for the engine reliability data. Numerical results are presented for five different groupings of the engine data that reflect the actual response to the failures.

Commercial Off-The-Shelf (COTS) Graphics Processing Board (GPB) Radiation Test Evaluation Report

NASA Technical Reports Server (NTRS)

Salazar, George A.; Steele, Glen F.

2013-01-01

Large round trip communications latency for deep space missions will require more onboard computational capabilities to enable the space vehicle to undertake many tasks that have traditionally been ground-based, mission control responsibilities. As a result, visual display graphics will be required to provide simpler vehicle situational awareness through graphical representations, as well as provide capabilities never before done in a space mission, such as augmented reality for in-flight maintenance or Telepresence activities. These capabilities will require graphics processors and associated support electronic components for high computational graphics processing. In an effort to understand the performance of commercial graphics card electronics operating in the expected radiation environment, a preliminary test was performed on five commercial offthe- shelf (COTS) graphics cards. This paper discusses the preliminary evaluation test results of five COTS graphics processing cards tested to the International Space Station (ISS) low earth orbit radiation environment. Three of the five graphics cards were tested to a total dose of 6000 rads (Si). The test articles, test configuration, preliminary results, and recommendations are discussed.

Mechanical characterization of poly-SiGe layers for CMOS-MEMS integrated application

NASA Astrophysics Data System (ADS)

Modlinski, Robert; Witvrouw, Ann; Verbist, Agnes; Puers, Robert; De Wolf, Ingrid

2010-01-01

Measuring mechanical properties at the microscale is essential to understand and to fabricate reliable MEMS. In this paper a tensile testing system and matching microscale test samples are presented. The test samples have a dog-bone-like structure. They are designed to mimic standard macro-tensile test samples. The micro-tensile tests are used to characterize 0.9 µm thick polycrystalline silicon germanium (poly-SiGe) films. The poly-SiGe film, that can be considered as a close equivalent to polycrystalline silicon (poly-Si), is studied as a very promising material for use in CMOS/MEMS integration in a single chip due to its low-temperature LPCVD deposition (T < 450 °C). The fabrication process of the poly-SiGe micro-tensile test structure is explained in detail: the design, the processing and post-processing, the testing and finally the results' discussion. The poly-SiGe micro-tensile results are also compared with nanoindentation data obtained on the same poly-SiGe films as well as with results obtained by other research groups.

Mechanical Design of a Performance Test Rig for the Turbine Air-Flow Task (TAFT)

NASA Technical Reports Server (NTRS)

Xenofos, George; Forbes, John; Farrow, John; Williams, Robert; Tyler, Tom; Sargent, Scott; Moharos, Jozsef

2003-01-01

To support development of the Boeing-Rocketdyne RS84 rocket engine, a fill-flow, reaction turbine geometry was integrated into the NASA-MSFC turbine air-flow test facility. A mechanical design was generated which minimized the amount of new hardware while incorporating all test and instrUmentation requirements. This paper provides details of the mechanical design for this Turbine Air-Flow Task (TAFT) test rig. The mechanical design process utilized for this task included the following basic stages: Conceptual Design. Preliminary Design. Detailed Design. Baseline of Design (including Configuration Control and Drawing Revision). Fabrication. Assembly. During the design process, many lessons were learned that should benefit future test rig design projects. Of primary importance are well-defined requirements early in the design process, a thorough detailed design package, and effective communication with both the customer and the fabrication contractors. The test rig provided steady and unsteady pressure data necessary to validate the computational fluid dynamics (CFD) code. The rig also helped characterize the turbine blade loading conditions. Test and CFD analysis results are to be presented in another JANNAF paper.

Accounting for Proof Test Data in a Reliability Based Design Optimization Framework

NASA Technical Reports Server (NTRS)

Ventor, Gerharad; Scotti, Stephen J.

2012-01-01

This paper investigates the use of proof (or acceptance) test data during the reliability based design optimization of structural components. It is assumed that every component will be proof tested and that the component will only enter into service if it passes the proof test. The goal is to reduce the component weight, while maintaining high reliability, by exploiting the proof test results during the design process. The proposed procedure results in the simultaneous design of the structural component and the proof test itself and provides the designer with direct control over the probability of failing the proof test. The procedure is illustrated using two analytical example problems and the results indicate that significant weight savings are possible when exploiting the proof test results during the design process.

A novel eco-friendly technique for efficient control of lime water softening process.

PubMed

Ostovar, Mohamad; Amiri, Mohamad

2013-12-01

Lime softening is an established type of water treatment used for water softening. The performance of this process is highly dependent on lime dosage. Currently, lime dosage is adjusted manually based on chemical tests, aimed at maintaining the phenolphthalein (P) and total (M) alkalinities within a certain range (2 P - M > or = 5). In this paper, a critical study of the softening process has been presented. It has been shown that the current method is frequently incorrect. Furthermore, electrical conductivity (EC) has been introduced as a novel indicator for effectively characterizing the lime softening process.This novel technique has several advantages over the current alkalinities method. Because no chemical reagents are needed for titration, which is a simple test, there is a considerable reduction in test costs. Additionally, there is a reduction in the treated water hardness and generated sludge during the lime softening process. Therefore, it is highly eco-friendly, and is a very cost effective alternative technique for efficient control of the lime softening process.

Validation study and routine control monitoring of moist heat sterilization procedures.

PubMed

Shintani, Hideharu

2012-06-01

The proposed approach to validation of steam sterilization in autoclaves follows the basic life cycle concepts applicable to all validation programs. Understand the function of sterilization process, develop and understand the cycles to carry out the process, and define a suitable test or series of tests to confirm that the function of the process is suitably ensured by the structure provided. Sterilization of product and components and parts that come in direct contact with sterilized product is the most critical of pharmaceutical processes. Consequently, this process requires a most rigorous and detailed approach to validation. An understanding of the process requires a basic understanding of microbial death, the parameters that facilitate that death, the accepted definition of sterility, and the relationship between the definition and sterilization parameters. Autoclaves and support systems need to be designed, installed, and qualified in a manner that ensures their continued reliability. Lastly, the test program must be complete and definitive. In this paper, in addition to validation study, documentation of IQ, OQ and PQ concretely were described.

DDS-Suite - A Dynamic Data Acquisition, Processing, and Analysis System for Wind Tunnel Testing

NASA Technical Reports Server (NTRS)

Burnside, Jathan J.

2012-01-01

Wind Tunnels have optimized their steady-state data systems for acquisition and analysis and even implemented large dynamic-data acquisition systems, however development of near real-time processing and analysis tools for dynamic-data have lagged. DDS-Suite is a set of tools used to acquire, process, and analyze large amounts of dynamic data. Each phase of the testing process: acquisition, processing, and analysis are handled by separate components so that bottlenecks in one phase of the process do not affect the other, leading to a robust system. DDS-Suite is capable of acquiring 672 channels of dynamic data at rate of 275 MB / s. More than 300 channels of the system use 24-bit analog-to-digital cards and are capable of producing data with less than 0.01 of phase difference at 1 kHz. System architecture, design philosophy, and examples of use during NASA Constellation and Fundamental Aerodynamic tests are discussed.

Design of an MR image processing module on an FPGA chip

NASA Astrophysics Data System (ADS)

Li, Limin; Wyrwicz, Alice M.

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments.

Microstructure and mechanical properties of nickel coated multi walled carbon nanotube reinforced stainless steel 316L matrix composites by laser sintering process

NASA Astrophysics Data System (ADS)

Mahanthesha, P.; Mohankumar, G. C.

2018-04-01

Electroless Ni coated Multi-walled Carbon nanotubes reinforced with Stainless Steel 316L matrix composite was developed by Direct Metal Laser Sintering process (DMLS). Homogeneous mixture of Stainless Steel 316L powder and carbon nanotubes in different vol. % was obtained by using double cone blender machine. Characterization of electroless Ni coated carbon nanotubes was done by using X-ray diffraction, FESEM and EDS. Test samples were fabricated at different laser scan speeds. Effect of process parameters and CNT vol. % content on solidification microstructure and mechanical properties of test samples was investigated by using Optical microscopy, FESEM, and Hounsfield tensometer. Experimental results reveal DMLS process parameters affect the density and microstructure of sintered parts. Dense parts with minimum porosity when processed at low laser scan speeds and low CNT vol. %. Tensile fractured surface of test specimens evidences the survival of carbon nanotubes under high temperature processing condition.

Design of an MR image processing module on an FPGA chip

PubMed Central

Li, Limin; Wyrwicz, Alice M.

2015-01-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. PMID:25909646

How holistic processing of faces relates to cognitive control and intelligence.

PubMed

Gauthier, Isabel; Chua, Kao-Wei; Richler, Jennifer J

2018-04-16

The Vanderbilt Holistic Processing Test for faces (VHPT-F) is the first standard test designed to measure individual differences in holistic processing. The test measures failures of selective attention to face parts through congruency effects, an operational definition of holistic processing. However, this conception of holistic processing has been challenged by the suggestion that it may tap into the same selective attention or cognitive control mechanisms that yield congruency effects in Stroop and Flanker paradigms. Here, we report data from 130 subjects on the VHPT-F, several versions of Stroop and Flanker tasks, as well as fluid IQ. Results suggested a small degree of shared variance in Stroop and Flanker congruency effects, which did not relate to congruency effects on the VHPT-F. Variability on the VHPT-F was also not correlated with Fluid IQ. In sum, we find no evidence that holistic face processing as measured by congruency in the VHPT-F is accounted for by domain-general control mechanisms.

LEACHING OF METALS FROM MINERAL PROCESSING WASTE

EPA Science Inventory

The purpose of this project is to test the leaching of Mineral processing Waste (MPW) contaminated with heavy metals using scientifically defendable leaching tests other than TCLP. Past experience and literature have shown that TCLP underestiates the levels of metals such as oxoa...

MTR AND ETR COMPLEXES. CAMERA FACING EASTERLY TOWARD CHEMICAL PROCESSING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR AND ETR COMPLEXES. CAMERA FACING EASTERLY TOWARD CHEMICAL PROCESSING PLANT. MTR AND ITS ATTACHMENTS IN FOREGROUND. ETR BEYOND TO RIGHT. INL NEGATIVE NO. 56-4100. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

LEACHING OF METALS FROM MINERAL PROCESSING WASTE

EPA Science Inventory

The purpose of this project is to test the leaching of Mineral Processing Waste (MPW) contaminated with heavy metals using scientifically defendable leaching tests other than TCLP. Past experience and literature have shown that TCLP underestimates the levels of metals such as oxo...

Coal Technology Program progress report, March 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Shakedown tests of the bench-scale hydrocarbonization system were successfully completed. Wyodak coal was fed to the reactor at a rate of 9.9 lb/hr where it was hydrocarbonized at 1050/sup 0/F under 20-atm hydrogen pressure. Laboratory results including settling tests, bench-scale settling tests, and sample ageing tests were continued. Two of ten compounds tested with the laboratory-scale apparatus were effective in increasing settling rates of solids in Solvent Refined Coal unfiltered oil, but bench-scale tests failed to show any improvements in the settling rate over the untreated SRC-UFO. Analytical chemistry efforts involved the removal and concentration of organic components in by-productmore » waters from fossil fuel conversion processes. A sephadex gel is being used to achieve hydrophilic-lipophilic separations in organic mixtures as a step in the analysis of fossil fuel related materials. Engineering Evaluations of the Synthiol and Hydrocarbonization Processes continued with the Synthiol process flow diagrams, heat and material balances, and utilities requirements being completed. Inspection techniques were developed for wear- and process-resistant coatings. Orders were placed for the Incoloy 800 tubing and a smaller quantity of Inconel 600 tubing for the tube matrix in the coal-fueled MIUS fluidized bed. An engineering feasibility review of General Atomic's proposal to ERDA for a bench-scale test program on thermochemical water splitting for hydrogen production was completed. (auth)« less

Central auditory processing and migraine: a controlled study

PubMed Central

2014-01-01

Background This study aimed to verify and compare central auditory processing (CAP) performance in migraine with and without aura patients and healthy controls. Methods Forty-one volunteers of both genders, aged between 18 and 40 years, diagnosed with migraine with and without aura by the criteria of “The International Classification of Headache Disorders” (ICDH-3 beta) and a control group of the same age range and with no headache history, were included. Gaps-in-noise (GIN), Duration Pattern test (DPT) and Dichotic Digits Test (DDT) tests were used to assess central auditory processing performance. Results The volunteers were divided into 3 groups: Migraine with aura (11), migraine without aura (15), and control group (15), matched by age and schooling. Subjects with aura and without aura performed significantly worse in GIN test for right ear (p = .006), for left ear (p = .005) and for DPT test (p < .001) when compared with controls without headache, however no significant differences were found in the DDT test for the right ear (p = .362) and for the left ear (p = .190). Conclusions Subjects with migraine performed worsened in auditory gap detection, in the discrimination of short and long duration. They also presented impairment in the physiological mechanism of temporal processing, especially in temporal resolution and temporal ordering when compared with controls. Migraine could be related to an impaired central auditory processing. Clinical trial registration Research Ethics Committee (CEP 0480.10) – UNIFESP PMID:25380661

Evaluation of continuous oxydesulfurization processes. Final technical report, September 1979-July 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, J.F.; Wever, D.M.

1981-07-01

Three processes developed by Pittsburgh Energy Technology Center (PETC), Ledgemont Laboratories, and Ames Laboratories for the oxydesulfurization of coal were evaluated in continuous processing equipment designed, built, and/or adapted for the purpose at the DOE-owned Multi-Use Fuels and Energy Processes Test Plant (MEP) located at TRW's Capistrano Test Site in California. The three processes differed primarily in the chemical additives (none, sodium carbonate, or ammonia), fed to the 20% to 40% coal/water slurries, and in the oxygen content of the feed gas stream. Temperature, pressure, residence time, flow rates, slurry concentration and stirrer speed were the other primary independent variables.more » The amount of organic sulfur removed, total sulfur removed and the Btu recovery were the primary dependent variables. Evaluation of the data presented was not part of the test effort.« less

Pyrotechnic hazards classification and evaluation program. Phase 2, segment 3: Test plan for determining hazards associated with pyrotechnic manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

A comprehensive test plan for determining the hazards associated with pyrotechnic manufacturing processes is presented. The rationale for each test is based on a systematic analysis of historical accounts of accidents and a detailed study of the characteristics of each manufacturing process. The most hazardous manufacturing operations have been determined to be pressing, mixing, reaming, and filling. The hazard potential of a given situation is evaluated in terms of the probabilities of initiation, communication, and transition to detonation (ICT). The characteristics which affect the ICT probabilities include the ignition mechanisms which are present either in normal or abnormal operation, the condition and properties of the pyrotechnic material, and the configuration of the processing equipment. Analytic expressions are derived which describe the physical conditions of the system, thus permitting a variety of processes to be evaluated in terms of a small number of experiments.

A methodology for evaluation of an interactive multispectral image processing system

NASA Technical Reports Server (NTRS)

Kovalick, William M.; Newcomer, Jeffrey A.; Wharton, Stephen W.

1987-01-01

Because of the considerable cost of an interactive multispectral image processing system, an evaluation of a prospective system should be performed to ascertain if it will be acceptable to the anticipated users. Evaluation of a developmental system indicated that the important system elements include documentation, user friendliness, image processing capabilities, and system services. The criteria and evaluation procedures for these elements are described herein. The following factors contributed to the success of the evaluation of the developmental system: (1) careful review of documentation prior to program development, (2) construction and testing of macromodules representing typical processing scenarios, (3) availability of other image processing systems for referral and verification, and (4) use of testing personnel with an applications perspective and experience with other systems. This evaluation was done in addition to and independently of program testing by the software developers of the system.

Assessment of Sensory Processing Characteristics in Children between 3 and 11 Years Old: A Systematic Review.

PubMed

Jorquera-Cabrera, Sara; Romero-Ayuso, Dulce; Rodriguez-Gil, Gemma; Triviño-Juárez, José-Matías

2017-01-01

The assessment of sensory perception, discrimination, integration, modulation, praxis, and other motor skills, such as posture, balance, and bilateral motor coordination, is necessary to identify the sensory and motor factors influencing the development of personal autonomy. The aim of this work is to study the assessment tools currently available for identifying different patterns of sensory processing. There are 15 tests available that have psychometric properties, primarily for the US population. Nine of them apply to children in preschool and up to grade 12. The assessment of sensory processing is a process that includes the use of standardized tests, administration of caregiver questionnaires, and clinical observations. The review of different studies using PRISMA criteria or Osteba Critical Appraisal Cards reveals that the most commonly used tools are the Sensory Integration and Praxis Test, the Sensory Processing Measure, and the Sensory Profile.

Assessment of Sensory Processing Characteristics in Children between 3 and 11 Years Old: A Systematic Review

PubMed Central

Jorquera-Cabrera, Sara; Romero-Ayuso, Dulce; Rodriguez-Gil, Gemma; Triviño-Juárez, José-Matías

2017-01-01

The assessment of sensory perception, discrimination, integration, modulation, praxis, and other motor skills, such as posture, balance, and bilateral motor coordination, is necessary to identify the sensory and motor factors influencing the development of personal autonomy. The aim of this work is to study the assessment tools currently available for identifying different patterns of sensory processing. There are 15 tests available that have psychometric properties, primarily for the US population. Nine of them apply to children in preschool and up to grade 12. The assessment of sensory processing is a process that includes the use of standardized tests, administration of caregiver questionnaires, and clinical observations. The review of different studies using PRISMA criteria or Osteba Critical Appraisal Cards reveals that the most commonly used tools are the Sensory Integration and Praxis Test, the Sensory Processing Measure, and the Sensory Profile. PMID:28424762

Quality by control: Towards model predictive control of mammalian cell culture bioprocesses.

PubMed

Sommeregger, Wolfgang; Sissolak, Bernhard; Kandra, Kulwant; von Stosch, Moritz; Mayer, Martin; Striedner, Gerald

2017-07-01

The industrial production of complex biopharmaceuticals using recombinant mammalian cell lines is still mainly built on a quality by testing approach, which is represented by fixed process conditions and extensive testing of the end-product. In 2004 the FDA launched the process analytical technology initiative, aiming to guide the industry towards advanced process monitoring and better understanding of how critical process parameters affect the critical quality attributes. Implementation of process analytical technology into the bio-production process enables moving from the quality by testing to a more flexible quality by design approach. The application of advanced sensor systems in combination with mathematical modelling techniques offers enhanced process understanding, allows on-line prediction of critical quality attributes and subsequently real-time product quality control. In this review opportunities and unsolved issues on the road to a successful quality by design and dynamic control implementation are discussed. A major focus is directed on the preconditions for the application of model predictive control for mammalian cell culture bioprocesses. Design of experiments providing information about the process dynamics upon parameter change, dynamic process models, on-line process state predictions and powerful software environments seem to be a prerequisite for quality by control realization. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Cognitive functions, their development and modern diagnostic methods].

PubMed

Klasik, Adam; Janas-Kozik, Małgorzata; Krupka-Matuszczyk, Irena; Augustyniak, Ewa

2006-01-01

Cognitive psychology is an interdisciplinary field whose main aim is to study the thinking mechanisms of humans leading to cognizance. Therefore the concept of human cognitive processes envelopes the knowledge related to the mechanisms which determine the way humans acquire information from the environment and utilize their knowledge and experience. There are three basic processes which need to be distinguished when discussing human perception development: acquiring sensations, perceptiveness and attention. Acquiring sensations means the experience arising from the stimulation of a single sense organ, i.e. detection and differentiation of sensory information. Perceptiveness stands for the interpretation of sensations and may include recognition and identification of sensory information. The attention process relates to the selectivity of perception. Mental processes of the higher order used in cognition, thanks to which humans tend to try to understand the world and adapt to it, doubtlessly include the processes of memory, reasoning, learning and problem solving. There is a great difference in the human cognitive functioning at different stages of one's life (from infancy to adulthood). The difference is both quantitative and qualitative. There are three main approaches to the human cognitive functioning development: Jean Piaget's approach, information processing approach and psychometric approach. Piaget's ideas continue to form the groundwork of child cognitive psychology. Piaget identified four developmental stages of child cognition: 1. Sensorimotor stage (birth - 2 years old); 2. Preoperational stage (ages 2-7); 3. Concrete operations (ages 7-11; 4. Formal operations (11 and more). The supporters of the information processing approach use a computer metaphor to present the human cognitive processes functioning model. The three important mechanisms involved are: coding, automation and strategy designing and they all often co-operate together. This theory has provided a theory. The psychometric approach concentrates on studying the differences in intelligence. The aim of this approach is to test intelligence by means of standardized tests (e.g. WISC-R, WAIS-R) used to show the individual differences among humans. Human cognitive functions determine individuals' adaptation capabilities and disturbances in this area indicate a number of psychopathological changes and are a symptom enabling to differentiate or diagnose one with a disorder. That is why the psychological assessment of cognitive functions is an important part of patients' diagnosis. Contemporary neuropsychological studies are to a great extent based computer tests. The use of computer methods has a number of measurement-related advantages. It allows for standardized testing environment, increasing therefore its reliability and standardizes the patient assessment process. Special attention should be paid to the neuropsychological tests included in the Vienna Test System (Cognitron, SIGNAL, RT, VIGIL, DAUF), which are used to assess the operational memory span, learning processes, reaction time, attention selective function, attention continuity as well as attention interference resistance. It also seems justified to present the CPT id test (Continuous Performance Test) as well as Free Recall. CPT is a diagnostic tool used to assess the attention selective function, attention continuity of attention, attention interference resistance as well as attention alertness. The Free Recall test is used in the memory processes diagnostics to assess patients' operational memory as well as the information organization degree in operational memory. The above mentioned neuropsychological tests are tools used in clinical assessment of cognitive function disorders.

Forest, Trees, Dynamics: Results from a Novel Wisconsin Card Sorting Test Variant Protocol for Studying Global-Local Attention and Complex Cognitive Processes

PubMed Central

Cowley, Benjamin; Lukander, Kristian

2016-01-01

Background: Recognition of objects and their context relies heavily on the integrated functioning of global and local visual processing. In a realistic setting such as work, this processing becomes a sustained activity, implying a consequent interaction with executive functions. Motivation: There have been many studies of either global-local attention or executive functions; however it is relatively novel to combine these processes to study a more ecological form of attention. We aim to explore the phenomenon of global-local processing during a task requiring sustained attention and working memory. Methods: We develop and test a novel protocol for global-local dissociation, with task structure including phases of divided (“rule search”) and selective (“rule found”) attention, based on the Wisconsin Card Sorting Task (WCST). We test it in a laboratory study with 25 participants, and report on behavior measures (physiological data was also gathered, but not reported here). We develop novel stimuli with more naturalistic levels of information and noise, based primarily on face photographs, with consequently more ecological validity. Results: We report behavioral results indicating that sustained difficulty when participants test their hypotheses impacts matching-task performance, and diminishes the global precedence effect. Results also show a dissociation between subjectively experienced difficulty and objective dimension of performance, and establish the internal validity of the protocol. Contribution: We contribute an advance in the state of the art for testing global-local attention processes in concert with complex cognition. With three results we establish a connection between global-local dissociation and aspects of complex cognition. Our protocol also improves ecological validity and opens options for testing additional interactions in future work. PMID:26941689

Routine failures in the process for blood testing and the communication of results to patients in primary care in the UK: a qualitative exploration of patient and provider perspectives

PubMed Central

Litchfield, Ian; Bentham, Louise; Hill, Ann; McManus, Richard J; Lilford, Richard; Greenfield, Sheila

2015-01-01

Background The testing and result communication process in primary care is complex. Its successful completion relies on the coordinated efforts of a range of staff in primary care and external settings working together with patients. Despite the importance of diagnostic testing in provision of care, this complexity renders the process vulnerable in the face of increasing demand, stretched resources and a lack of supporting guidance. Methods We conducted a series of focus groups with patients and staff across four primary care practices using process-improvement strategies to identify and understand areas where either unnecessary delay is introduced, or the process may fail entirely. We then worked with both patients and staff to arrive at practical strategies to improve the current system. Results A total of six areas across the process were identified where improvements could be introduced. These were: (1) delay in phlebotomy, (2) lack of a fail-safe to ensure blood tests are returned to practices and patients, (3) difficulties in accessing results by telephone, (4) role of non-clinical staff in communicating results, (5) routine communication of normal results and (6) lack of a protocol for result communication. Conclusions A number of potential failures in testing and communicating results to patients were identified, and some specific ideas for improving existing systems emerged. These included same-day phlebotomy sessions, use of modern technology methods to proactively communicate routine results and targeted training for receptionists handling sensitive data. There remains an urgent need for further work to test these and other potential solutions. PMID:26251507

Routine failures in the process for blood testing and the communication of results to patients in primary care in the UK: a qualitative exploration of patient and provider perspectives.

PubMed

Litchfield, Ian; Bentham, Louise; Hill, Ann; McManus, Richard J; Lilford, Richard; Greenfield, Sheila

2015-11-01

The testing and result communication process in primary care is complex. Its successful completion relies on the coordinated efforts of a range of staff in primary care and external settings working together with patients. Despite the importance of diagnostic testing in provision of care, this complexity renders the process vulnerable in the face of increasing demand, stretched resources and a lack of supporting guidance. We conducted a series of focus groups with patients and staff across four primary care practices using process-improvement strategies to identify and understand areas where either unnecessary delay is introduced, or the process may fail entirely. We then worked with both patients and staff to arrive at practical strategies to improve the current system. A total of six areas across the process were identified where improvements could be introduced. These were: (1) delay in phlebotomy, (2) lack of a fail-safe to ensure blood tests are returned to practices and patients, (3) difficulties in accessing results by telephone, (4) role of non-clinical staff in communicating results, (5) routine communication of normal results and (6) lack of a protocol for result communication. A number of potential failures in testing and communicating results to patients were identified, and some specific ideas for improving existing systems emerged. These included same-day phlebotomy sessions, use of modern technology methods to proactively communicate routine results and targeted training for receptionists handling sensitive data. There remains an urgent need for further work to test these and other potential solutions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

A systematic approach to the Planck LFI end-to-end test and its application to the DPC Level 1 pipeline

NASA Astrophysics Data System (ADS)

Frailis, M.; Maris, M.; Zacchei, A.; Morisset, N.; Rohlfs, R.; Meharga, M.; Binko, P.; Türler, M.; Galeotta, S.; Gasparo, F.; Franceschi, E.; Butler, R. C.; D'Arcangelo, O.; Fogliani, S.; Gregorio, A.; Lowe, S. R.; Maggio, G.; Malaspina, M.; Mandolesi, N.; Manzato, P.; Pasian, F.; Perrotta, F.; Sandri, M.; Terenzi, L.; Tomasi, M.; Zonca, A.

2009-12-01

The Level 1 of the Planck LFI Data Processing Centre (DPC) is devoted to the handling of the scientific and housekeeping telemetry. It is a critical component of the Planck ground segment which has to strictly commit to the project schedule to be ready for the launch and flight operations. In order to guarantee the quality necessary to achieve the objectives of the Planck mission, the design and development of the Level 1 software has followed the ESA Software Engineering Standards. A fundamental step in the software life cycle is the Verification and Validation of the software. The purpose of this work is to show an example of procedures, test development and analysis successfully applied to a key software project of an ESA mission. We present the end-to-end validation tests performed on the Level 1 of the LFI-DPC, by detailing the methods used and the results obtained. Different approaches have been used to test the scientific and housekeeping data processing. Scientific data processing has been tested by injecting signals with known properties directly into the acquisition electronics, in order to generate a test dataset of real telemetry data and reproduce as much as possible nominal conditions. For the HK telemetry processing, validation software have been developed to inject known parameter values into a set of real housekeeping packets and perform a comparison with the corresponding timelines generated by the Level 1. With the proposed validation and verification procedure, where the on-board and ground processing are viewed as a single pipeline, we demonstrated that the scientific and housekeeping processing of the Planck-LFI raw data is correct and meets the project requirements.

Measuring the Process and Quality of Informed Consent for Clinical Research: Development and Testing

PubMed Central

Cohn, Elizabeth Gross; Jia, Haomiao; Smith, Winifred Chapman; Erwin, Katherine; Larson, Elaine L.

2013-01-01

Purpose/Objectives To develop and assess the reliability and validity of an observational instrument, the Process and Quality of Informed Consent (P-QIC). Design A pilot study of the psychometrics of a tool designed to measure the quality and process of the informed consent encounter in clinical research. The study used professionally filmed, simulated consent encounters designed to vary in process and quality. Setting A major urban teaching hospital in the northeastern region of the United States. Sample 63 students enrolled in health-related programs participated in psychometric testing, 16 students participated in test-retest reliability, and 5 investigator-participant dyads were observed for the actual consent encounters. Methods For reliability and validity testing, students watched and rated videotaped simulations of four consent encounters intentionally varied in process and content and rated them with the proposed instrument. Test-retest reliability was established by raters watching the videotaped simulations twice. Inter-rater reliability was demonstrated by two simultaneous but independent raters observing an actual consent encounter. Main Research Variables The essential elements of information and communication for informed consent. Findings The initial testing of the P-QIC demonstrated reliable and valid psychometric properties in both the simulated standardized consent encounters and actual consent encounters in the hospital setting. Conclusions The P-QIC is an easy-to-use observational tool that provides a quick assessment of the areas of strength and areas that need improvement in a consent encounter. It can be used in the initial trainings of new investigators or consent administrators and in ongoing programs of improvement for informed consent. Implications for Nursing The development of a validated observational instrument will allow investigators to assess the consent process more accurately and evaluate strategies designed to improve it. PMID:21708532

Hydrothermal Testing of K Basin Sludge and N Reactor Fuel at Sludge Treatment Project Operating Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delegard, Calvin H.; Schmidt, Andrew J.; Thornton, Brenda M.

The Sludge Treatment Project (STP), managed for the U. S. DOE by Fluor Hanford (FH), was created to design and operate a process to eliminate uranium metal from K Basin sludge prior to packaging for Waste Isolation Pilot Plant (WIPP). The STP process uses high temperature liquid water to accelerate the reaction, produce uranium dioxide from the uranium metal, and safely discharge the hydrogen. Under nominal process conditions, the sludge will be heated in pressurized water at 185°C for as long as 72 hours to assure the complete reaction (corrosion) of up to 0.25-inch diameter uranium metal pieces. Under contractmore » to FH, the Pacific Northwest National Laboratory (PNNL) conducted bench-scale testing of the STP hydrothermal process in November and December 2006. Five tests (~50 ml each) were conducted in sealed, un-agitated reaction vessels under the hydrothermal conditions (e.g., 7 to 72 h at 185°C) of the STP corrosion process using radioactive sludge samples collected from the K East Basin and particles/coupons of N Reactor fuel also taken from the K Basins. The tests were designed to evaluate and understand the chemical changes that may be occurring and the effects that any changes would have on sludge rheological properties. The tests were not designed to evaluate engineering aspects of the process. The hydrothermal treatment affected the chemical and physical properties of the sludge. In each test, significant uranium compound phase changes were identified, resulting from dehydration and chemical reduction reactions. Physical properties of the sludge were significantly altered from their initial, as-settled sludge values, including, shear strength, settled density, weight percent water, and gas retention.« less

SOI-CMOS Process for Monolithic, Radiation-Tolerant, Science-Grade Imagers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, George; Lee, Adam

In Phase I, Voxtel worked with Jazz and Sandia to document and simulate the processes necessary to implement a DH-BSI SOI CMOS imaging process. The development is based upon mature SOI CMOS process at both fabs, with the addition of only a few custom processing steps for integration and electrical interconnection of the fully-depleted photodetectors. In Phase I, Voxtel also characterized the Sandia process, including the CMOS7 design rules, and we developed the outline of a process option that included a “BOX etch”, that will permit a “detector in handle” SOI CMOS process to be developed The process flows weremore » developed in cooperation with both Jazz and Sandia process engineers, along with detailed TCAD modeling and testing of the photodiode array architectures. In addition, Voxtel tested the radiation performance of the Jazz’s CA18HJ process, using standard and circular-enclosed transistors.« less

Potential Alternatives Report for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes

NASA Technical Reports Server (NTRS)

Lewis, pattie

2011-01-01

Identifying and selecting alternative materials and technologies that have the potential to reduce the identified HazMats and hazardous air pollutants (HAPs), while incorporating sound corrosion prevention and control technologies, is a complicated task due to the fast pace at which new technologies emerge and rules change. The alternatives are identified through literature searches, electronic database and Internet searches, surveys, and/or personal and professional contacts. Available test data was then compiled on the proposed alternatives to determine if the materials meet the test objectives or if further)laboratory or field-testing will be required. After reviewing technical information documented in the PAR, government representatives, technical representatives from the affected facilities, and other stakeholders involved in the process will select the list of viable alternative coatings for consideration and testing under the project's Joint Test Protocol entitled Joint Test Protocol for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes and Field Test Plan entitled Field Evaluations Test Plan for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes, both prepared by ITB. Test results will be reported in a Joint Test Report upon completion oftesting. The selection rationale and conclusions are documented in this PAR. A cost benefit analysis will be prepared to quantify the estimated capital and process costs of coating alternatives and cost savings relative to the current coating processes, however, some initial cost data has been included in this PAR. For this coatings project, isocyanates, as found in aliphatic isocyanate polyurethanes, were identified as the target HazMat to be eliminated. Table 1-1 lists the target HazMats, the related process and application, current specifications, and affected programs.

Testing of the BipiColombo Antenna Pointing Mechanism

NASA Astrophysics Data System (ADS)

Campo, Pablo; Barrio, Aingeru; Martin, Fernando

2015-09-01

BepiColombo is an ESA mission to Mercury, its planetary orbiter (MPO) has two antenna pointing mechanism, High gain antenna (HGA) pointing mechanism steers and points a large reflector which is integrated at system level by TAS-I Rome. Medium gain antenna (MGA) APM points a 1.5 m boom with a horn antenna. Both radiating elements are exposed to sun fluxes as high as 10 solar constants without protections.A previous paper [1] described the design and development process to solve the challenges of performing in harsh environment.. Current paper is focused on the testing process of the qualification units. Testing performance of antenna pointing mechanism in its specific environmental conditions has required special set-up and techniques. The process has provided valuable feedback on the design and the testing methods which have been included in the PFM design and tests.Some of the technologies and components were developed on dedicated items priort to EQM, but once integrated, test behaviour had relevant differences.Some of the major concerns for the APM testing are:- Create during the thermal vacuum testing the qualification temperature map with gradients along the APM. From of 200oC to 70oC.- Test in that conditions the radio frequency and pointing performances adding also high RF power to check the power handling and self-heating of the rotary joint.- Test in life up to 12000 equivalent APM revolutions, that is 14.3 million motor revolutions in different thermal conditions.- Measure low thermal distortion of the mechanical chain, being at the same time insulated from external environment and interfaces (55 arcsec pointing error)- Perform deployment of large items guaranteeing during the process low humidity, below 5% to protect dry lubrication- Verify stability with representative inertia of large boom or reflector 20 Kgm2.

The Hepatitis Testing and Linkage-to-Care Data Review Process: An Approach to Ensuring the Quality of Program Data.

PubMed

Mezzo, Jennifer L; Lamia, Tamara L; Danelski, Lisa L; Schipani, Anne Marie; Stokes, Scott A; Jacobs-Ware, Elizabeth D

2016-01-01

CDC's 2012 Hepatitis Testing and Linkage to Care (HepTLC) initiative was a nationally coordinated effort to conduct hepatitis B and hepatitis C screening, posttest counseling, and linkage to care at 34 U.S. sites. This project provided support for data management and monthly data reviews between awardees and a data manager, which facilitated monitoring of awardee progress and regular program improvement opportunities. CDC provided technical assistance to awardees for testing processes and program improvement, including Internet-based data submission, reporting software and data management to awardees, offering assistance with submitting, and reviewing data in real time. We describe how one awardee, AIDS Resource Center of Wisconsin (ARCW), used the data management process to improve data quality, inform testing processes and implementation, and measure and report missing variables from an online database. From October 2012 through July 2014, ARCW performed 2,255 HCV antibody (anti-HCV) tests and 244 HCV ribonucleic acid (RNA) tests as part of the HepTLC initiative. Participants who tested HCV RNA positive (n=189) were referred to medical care. At the end of the study, no records were missing for the anti-HCV test result or HCV RNA test result variables, and only one record was missing for those who were referred to medical care. Regular data review and monitoring by awardees and CDC-supported data managers provided opportunities for data quality and program improvement. Through regular data review, ARCW reduced the amount of missing data and promoted timely follow-up with participants testing positive for HCV to ensure receipt of results and linkage to care. Other programs can adopt a similar data management model.

Brain white matter structure and information processing speed in healthy older age.

PubMed

Kuznetsova, Ksenia A; Maniega, Susana Muñoz; Ritchie, Stuart J; Cox, Simon R; Storkey, Amos J; Starr, John M; Wardlaw, Joanna M; Deary, Ian J; Bastin, Mark E

2016-07-01

Cognitive decline, especially the slowing of information processing speed, is associated with normal ageing. This decline may be due to brain cortico-cortical disconnection caused by age-related white matter deterioration. We present results from a large, narrow age range cohort of generally healthy, community-dwelling subjects in their seventies who also had their cognitive ability tested in youth (age 11 years). We investigate associations between older age brain white matter structure, several measures of information processing speed and childhood cognitive ability in 581 subjects. Analysis of diffusion tensor MRI data using Tract-based Spatial Statistics (TBSS) showed that all measures of information processing speed, as well as a general speed factor composed from these tests (g speed), were significantly associated with fractional anisotropy (FA) across the white matter skeleton rather than in specific tracts. Cognitive ability measured at age 11 years was not associated with older age white matter FA, except for the g speed-independent components of several individual processing speed tests. These results indicate that quicker and more efficient information processing requires global connectivity in older age, and that associations between white matter FA and information processing speed (both individual test scores and g speed), unlike some other aspects of later life brain structure, are generally not accounted for by cognitive ability measured in youth.

Development of the technology for the fabrication of reliable laminar from control panels

NASA Technical Reports Server (NTRS)

Meade, L. E.; Kays, A. O.; Ferrill, R. S.; Young, H. R.

1977-01-01

Materials were assessed and fabrication techniques were developed for use in the manufacture of wing surface materials compatible with the application of both aluminum alloys and nonmetallic composites. The concepts investigated included perforations and slots in the metallic test panels and microporosity and perforations in the composite test panels. Perforations were produced in the metallic test panels by the electron beam process and slots were developed by controlled gaps between the metal sheets. Microporosity was produced in the composite test panels by the resin bleed process, and perforations were produced by the fugitive fiber technique. Each of these concepts was fabricated into test panels, and air flow tests were conducted on the panels.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2013-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

A Survey of UML Based Regression Testing

NASA Astrophysics Data System (ADS)

Fahad, Muhammad; Nadeem, Aamer

Regression testing is the process of ensuring software quality by analyzing whether changed parts behave as intended, and unchanged parts are not affected by the modifications. Since it is a costly process, a lot of techniques are proposed in the research literature that suggest testers how to build regression test suite from existing test suite with minimum cost. In this paper, we discuss the advantages and drawbacks of using UML diagrams for regression testing and analyze that UML model helps in identifying changes for regression test selection effectively. We survey the existing UML based regression testing techniques and provide an analysis matrix to give a quick insight into prominent features of the literature work. We discuss the open research issues like managing and reducing the size of regression test suite, prioritization of the test cases that would be helpful during strict schedule and resources that remain to be addressed for UML based regression testing.

Constructing Aligned Assessments Using Automated Test Construction

ERIC Educational Resources Information Center

Porter, Andrew; Polikoff, Morgan S.; Barghaus, Katherine M.; Yang, Rui

2013-01-01

We describe an innovative automated test construction algorithm for building aligned achievement tests. By incorporating the algorithm into the test construction process, along with other test construction procedures for building reliable and unbiased assessments, the result is much more valid tests than result from current test construction…

Semi-physical simulation test for micro CMOS star sensor

NASA Astrophysics Data System (ADS)

Yang, Jian; Zhang, Guang-jun; Jiang, Jie; Fan, Qiao-yun

2008-03-01

A designed star sensor must be extensively tested before launching. Testing star sensor requires complicated process with much time and resources input. Even observing sky on the ground is a challenging and time-consuming job, requiring complicated and expensive equipments, suitable time and location, and prone to be interfered by weather. And moreover, not all stars distributed on the sky can be observed by this testing method. Semi-physical simulation in laboratory reduces the testing cost and helps to debug, analyze and evaluate the star sensor system while developing the model. The test system is composed of optical platform, star field simulator, star field simulator computer, star sensor and the central data processing computer. The test system simulates the starlight with high accuracy and good parallelism, and creates static or dynamic image in FOV (Field of View). The conditions of the test are close to observing real sky. With this system, the test of a micro star tracker designed by Beijing University of Aeronautics and Astronautics has been performed successfully. Some indices including full-sky autonomous star identification time, attitude update frequency and attitude precision etc. meet design requirement of the star sensor. Error source of the testing system is also analyzed. It is concluded that the testing system is cost-saving, efficient, and contributes to optimizing the embed arithmetic, shortening the development cycle and improving engineering design processes.

Test anxiety in relation to measures of cognitive and intellectual functioning.

PubMed

Gass, Carlton S; Curiel, Rosie E

2011-08-01

The potential impact of test anxiety on cognitive testing was examined in a sample of 300 predominantly male veteran referrals who were administered a comprehensive neuropsychological test battery. Exclusionary criteria included failure on effort testing (n= 14). Level of test anxiety was significantly related to performance on the WAIS-III Working Memory Index (r = -.343, p < .001) but not to scores on the Processing Speed, Perceptual Organization, or Verbal Comprehension indexes. Test anxiety was not related to a global index of neuropsychological performance on the HRNES-R (Average Impairment Scale). Level of education had a collinear relationship with test anxiety in predicting cognitive test performance. Regression analyses revealed a more prominent role for education, indicating the possibility that test anxiety may be a reaction to, more than a cause of, deficient working memory performance. These results suggest that clinicians who use these particular tests should be reluctant to attribute poor test performance to anxiety that occurs during the testing process.

Monsanto may bypass NIH in microbe test.

PubMed

Sun, Marjorie

1985-01-11

The Monsanto Company is planning to ask the Environmental Protection Agency for clearance to field test a genetically engineered microbial pesticide, bypassing the traditional approval process of the National Institutes of Health. Although only federally funded institutions are required to obtain NIH approval for genetic engineering tests, Monsanto is the first company to bypass the NIH regulatory process, which has become mired in a lawsuit brought by Jeremy Rifkin.

Process for Testing Compaction of a Swaged Heater for an Anode Sub-Assembly of a Hollow Cathode Assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2003-01-01

A process for testing compaction of a swaged heater for an anode sub-assembly of a Hollow Cathode Assembly (HCA), in which a test sample is cleaned, its mass measured before and after immersion in kerosene for 24 hours, and a compaction percentage calculated. A swaged heater is rejected if the compaction percentage exceeds 84%, plus or minus 4%.

Study on the application of the time-compressed speech in children.

PubMed

Padilha, Fernanda Yasmin Odila Maestri Miguel; Pinheiro, Maria Madalena Canina

2017-11-09

To analyze the performance of children without alteration of central auditory processing in the Time-compressed Speech Test. This is a descriptive, observational, cross-sectional study. Study participants were 22 children aged 7-11 years without central auditory processing disorders. The following instruments were used to assess whether these children presented central auditory processing disorders: Scale of Auditory Behaviors, simplified evaluation of central auditory processing, and Dichotic Test of Digits (binaural integration stage). The Time-compressed Speech Test was applied to the children without auditory changes. The participants presented better performance in the list of monosyllabic words than in the list of disyllabic words, but with no statistically significant difference. No influence on test performance was observed with respect to order of presentation of the lists and the variables gender and ear. Regarding age, difference in performance was observed only in the list of disyllabic words. The mean score of children in the Time-compressed Speech Test was lower than that of adults reported in the national literature. Difference in test performance was observed only with respect to the age variable for the list of disyllabic words. No difference was observed in the order of presentation of the lists or in the type of stimulus.