Transonic Drag Reduction Through Trailing-Edge Blowing on the FAST-MAC Circulation Control Model

NASA Technical Reports Server (NTRS)

Chan, David T.; Jones, Gregory S.; Milholen, William E., II; Goodliff, Scott L.

2017-01-01

A third wind tunnel test of the FAST-MAC circulation control semi-span model was completed in the National Transonic Facility at the NASA Langley Research Center where the model was configured for transonic testing of the cruise configuration with 0deg flap detection to determine the potential for transonic drag reduction with the circulation control blowing. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged ap. Recent upgrades to transonic semi-span flow control testing at the NTF have demonstrated an improvement to overall data repeatability, particularly for the drag measurement, that allows for increased confidence in the data results. The static thrust generated by the blowing slot was removed from the wind-on data using force and moment balance data from wind-o thrust tares. This paper discusses the impact of the trailing-edge blowing to the transonic aerodynamics of the FAST-MAC model in the cruise configuration, where at flight Reynolds numbers, the thrust-removed corrected data showed that an overall drag reduction and increased aerodynamic efficiency was realized as a consequence of the blowing.

Concussion: comparison of humans and rats.

PubMed

Parkinson, D; West, M; Pathiraja, T

1978-01-01

Concussion is the most primitive and probably the most simple central nervous system response to an outside agent. Although millions of neurons undergo a very rapid reversal with loss and restoration of function, many physicians argue that every knockout blow leaves some residual damage, i.e., some or all of these neurons stop short of recovery. Clinical experience shows a wide discrepancy in the appearance or persistence of certain signs and symptoms after all types of head injury, but particularly after concussing blows, when third party or grievance cases are involved. Using slow motion filmstrips of boxing ring knockouts, we established a grading system for concussion and duplicated these grades in nonanesthetized rats. When we compared the performance, learning, and memory of concussed rats with their preconcussion performance and with the performance of nonconcussed controls, we were unable to find any differences.

Prospective Teachers' Value Orientations as Determinants of Preference for External and Anonymous Whistleblowing

ERIC Educational Resources Information Center

Gokce, Asiye Toker

2013-01-01

Whistle-blowing indicates disclosing organizational wrongdoings resulting in harm to third parties. An individual's decision to blow the whistle might be based upon organizational, situational or personal factors. This study inquires the relationship between value orientations of prospective teachers and choices for whistle-blowing with particular…

Cryoinsulation Material Development to Mitigate Obsolescence Risk for Global Warming Potential Foams

NASA Technical Reports Server (NTRS)

Protz, Alison; Bruyns, Roland; Nettles, Mindy

2015-01-01

Cryoinsulation foams currently being qualified for the Space Launch System (SLS) core stage are nonozone- depleting substances (ODP) and are compliant with current environmental regulations. However, these materials contain the blowing agent HFC-245fa, a hydrofluorocarbon (HFC), which is a Global Warming Potential (GWP) substance. In August 2014, the Environmental Protection Agency (EPA) proposed a policy change to reduce or eliminate certain HFCs, including HFC-245fa, in end-use categories including foam blowing agents beginning in 2017. The policy proposes a limited exception to allow continued use of HFC and HFC-blend foam blowing agents for military or space- and aeronautics-related applications, including rigid polyurethane spray foams, but only until 2022.

Asymptotic properties of blow-up solutions in reaction-diffusion equations with nonlocal boundary flux

NASA Astrophysics Data System (ADS)

Liu, Bingchen; Dong, Mengzhen; Li, Fengjie

2018-04-01

This paper deals with a reaction-diffusion problem with coupled nonlinear inner sources and nonlocal boundary flux. Firstly, we propose the critical exponents on nonsimultaneous blow-up under some conditions on the initial data. Secondly, we combine the scaling technique and the Green's identity method to determine four kinds of simultaneous blow-up rates. Thirdly, the lower and the upper bounds of blow-up time are derived by using Sobolev-type differential inequalities.

40 CFR 63.8698 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... water with an emulsifying agent) are not subject to this subpart. Blowing still means the equipment in..., called “blowing,” is the oxidation of asphalt flux, achieved by bubbling air through the heated asphalt... facility includes one or more asphalt flux blowing stills, asphalt flux storage tanks storing asphalt flux...

40 CFR 63.8698 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... water with an emulsifying agent) are not subject to this subpart. Blowing still means the equipment in..., called “blowing,” is the oxidation of asphalt flux, achieved by bubbling air through the heated asphalt... facility includes one or more asphalt flux blowing stills, asphalt flux storage tanks storing asphalt flux...

40 CFR 63.8698 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... water with an emulsifying agent) are not subject to this subpart. Blowing still means the equipment in..., called “blowing,” is the oxidation of asphalt flux, achieved by bubbling air through the heated asphalt... facility includes one or more asphalt flux blowing stills, asphalt flux storage tanks storing asphalt flux...

Study of Microstructure and Mechanical Properties of Particulate Reinforced Aluminum Matrix Composite Foam

NASA Astrophysics Data System (ADS)

Kumar, Suresh; Pandey, O. P.

Metal foams cellular metals have gained an important role in the field of metallurgy, though barely a few decades old. Aluminum composite foam exhibit unique properties such as light weight, blast palliation, sound absorption, high energy absorption, and flame resistance. In the present investigation the effect of variation in the amount of CaCO3 as blowing agent on the microstructure and wear behavior of LM13 alloy foams has been studied. The blowing agent was blended in highly viscous semi-solid melt by stirring process. The process parameters that influence the formation of bubbles like the melt temperature, size and amount of blowing agent and its distribution has been optimized to get uniform size foams. The distribution behavior of blowing agent is influenced by the melt viscosity and stirring speed. For packaging application, the dry sliding wear behavior of the prepared foam was investigated by using a pin on disc method at applied loads of 9.8, 19.6 and 29.4 N at room temperature. The results indicate that the wear rate is dependent on the cell size and cell wall thickness of the foam.

Nanocellular thermoplastic foam and process for making the same

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Lingbo; Costeux, Stephane; Patankar, Kshitish A.

Prepare a thermoplastic polymer foam having a porosity of 70% or more and at least one of: (i) an average cell size of 200 nanometers or less; and (ii) a nucleation density of at least 1.times.1015 effective nucleation sites per cubic centimeter of foamable polymer composition not including blowing agent using a foamable polymer composition containing a thermoplastic polymer selected from styrenic polymer and (meth)acrylic polymers, a blowing agent comprising at least 20 mole-percent carbon dioxide based on moles of blowing agent and an additive having a Total Hansen Solubility Parameter that differs from that of carbon dioxide by lessmore » than 2 and that is present at a concentration of 0.01 to 1.5 weight parts per hundred weight parts thermoplastic polymer.« less

A review of the feasibility of lightening structural polymeric composites with voids without compromising mechanical properties.

PubMed

Rutz, Benjamin H; Berg, John C

2010-10-15

High performance polymer-fiber composites are high strength, low weight materials that have many applications, many of which would benefit from a decrease in weight, without a decrease in material properties. Generally, the fibers serve as the main load carriers, while the matrix serves to distribute load and protect the fibers from the environment. Thus, it is postulated that if the volume fraction of matrix is reduced, while still ensuring complete wetting of the fibers by the matrix, the per unit weight, i.e., specific, mechanical properties could be improved. This can be done by introducing small, spherical bubbles. Given the small average inter-fiber distance and assuming that the bubbles must not interact with the surface of the reinforcements the bubble diameter would need to be less than 1 μm. Introducing bubbles this small and ensuring that they do not form, or become attached, on the surface of the reinforcement are significant challenges. Two methods to produce such bubbles and the effect of these bubbles on mechanical properties of neat resins are reviewed: the addition of hollow spherical fillers, called microballoons, and the creation of bubbles from blowing agents. Microballoons in resins are a class of materials called syntactic foams. Although commercial microballoons are too large, smaller diameters can be made and could be used to reduce the weight of a reinforced composite on the order of 10%. The use of a physical blowing agent to produce bubbles in a composite is also considered. However, traditional polymer foaming techniques may be inadequate, as nucleation on the reinforcing phase is likely, and the bubbles formed are generally too large, so the use of blowing agent wells is considered. Blowing agent wells are discontinuous regions made from copolymer micelles or immiscible polymers that act as reservoirs of blowing agent. Additionally, the use of nano-sized materials for use as heterogeneous nucleation sites and secondary reinforcement of the matrix is also considered. Bubbles made from blowing agent could reduce the weight slightly more than using hollow spheres, but the reduction would also be of the order of 10%. Copyright © 2010 Elsevier B.V. All rights reserved.

European emissions of HFC-365mfc, a chlorine-free substitute for the foam blowing agents HCFC-141b and CFC-11.

PubMed

Stemmler, Konrad; Folini, Doris; Ubl, Sandy; Vollmer, Martin K; Reimann, Stefan; O'Doherty, Simon; Greally, Brian R; Simmonds, Peter G; Manning, Alistair J

2007-02-15

HFC-365mfc (1,1,1,3,3-pentafluorobutane) is an industrial chemical used for polyurethane foam blowing. From early 2003, HFC-365mfc has been commercially produced as a substitute for HCFC-141b, whose use in Europe has been banned since January 2004. We describe the first detection of HFC-365mfc in the atmosphere and report on a 2 year long record at the high Alpine station of Jungfraujoch (Switzerland) and the Atlantic coast station of Mace Head (Ireland). The measurements at Jungfraujoch are used to estimate the central European emissions of HFC-365mfc, HCFC-141b, and CFC-11. For HFC-365mfc, we estimate the central European emissions (Germany, France, Italy, Switzerland, The Netherlands, Belgium, and Luxembourg) in 2003 and 2004 as 400-500 tonnes year(-1). These emissions are about one-third lower on a per capita basis than what we estimate from the Mace Head measurements for the total of Europe. The estimated emissions of HCFC-141b for central Europe are higher (i.e., 7.2-3.5 ktonnes year(-1)) with a decreasing trend in the period from 2000 to 2004. Residual emissions of CFC-11 are estimated at 2.4-4.7 ktonnes year(-1) in the same time period. The Po Valley (northern Italy) appears to be a main source region for HFC-365mfc and for the former blowing agents HCFC-141b and CFC-11. In 2004, the emissions of HFC-365mfc arose from a wider region of Europe, which we attribute to an increased penetration of HFC-365mfc into the European market.

Wind Tunnel Results of Pneumatic Forebody Vortex Control Using Rectangular Slots a Chined Forebody

NASA Technical Reports Server (NTRS)

Alexander, Michael; Meyn, Larry A.

1994-01-01

A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.

Extrusion foaming of thermoplastic cellulose acetate from renewable resources using a two-component physical blowing agent system

NASA Astrophysics Data System (ADS)

Hopmann, Ch.; Windeck, C.; Hendriks, S.; Zepnik, S.; Wodke, T.

2014-05-01

Thermoplastic cellulose acetate (CA) is a bio-based polymer with optical, mechanical and thermal properties comparable to those of polystyrene (PS). The substitution of the predominant petrol-based PS in applications like foamed food trays can lead to a more sustainable economic practice. However, CA is also suitable for more durable applications as the biodegradability rate can be controlled by adjusting the degree of substitutions. The extrusion foaming of CA still has to overcome certain challenges. CA is highly hydrophilic and can suffer from hydrolytic degradation if not dried properly. Therefore, the influence of residual moisture on the melt viscosity is rather high. Beyond, the surface quality of foam CA sheets is below those of PS due to the particular foaming behaviour. This paper presents results of a recent study on extrusion foamed CA, using a two-component physical blowing agent system compromising HFO 1234ze as blowing agent and organic solvents as co-propellant. Samples with different co-propellants are processed on a laboratory single screw extruder at IKV. Morphology and surface topography are investigated with respect to the blowing agent composition and the die pressure. In addition, relationships between foam density, foam morphology and the propellants are analysed. The choice of the co-propellant has a significant influence on melt-strength, foaming behaviour and the possible blow-up ratio of the sheet. Furthermore, a positive influence of the co-propellant on the surface quality can be observed. In addition, the focus is laid on the effect of external contact cooling of the foamed sheets after the die exit.

Impact of the lower third molar presence and position on the fragility of mandibular angle and condyle: A Three-dimensional finite element study.

PubMed

Antic, Svetlana; Vukicevic, Arso M; Milasinovic, Marko; Saveljic, Igor; Jovicic, Gordana; Filipovic, Nenad; Rakocevic, Zoran; Djuric, Marija

2015-07-01

The aim of the present study was to investigate the influences of the presence and position of a lower third molar (M3) on the fragility of mandibular angle and condyle, using finite element analysis. From computed tomographic scans of a human mandible with normally erupted M3, two additional virtual models were generated: a mandibular model with partially impacted M3 and a model without M3. Two cases of impact were considered: a frontal and a lateral blow. The results are based on the chromatic analysis of the distributed von Mises and principal stresses, and calculation of their failure indices. In the frontal blow, the angle region showed the highest stress in the case with partially impacted M3, and the condylar region in the case without M3. Compressive stresses were dominant but caused no failure. Tensile stresses were recorded in the retromolar areas, but caused failure only in the case with partially impacted M3. In the lateral blow, the stress concentrated at the point of impact, in the ipsilateral and contralateral angle and condylar regions. The highest stresses were recorded in the case with partially impacted M3. Tensile stresses caused the failure on the ipsilateral side, whereas compressive stresses on the contralateral side. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Gamma-irradiated cross-linked LDPE foams: Characteristics and properties

NASA Astrophysics Data System (ADS)

Cardoso, E. C. L.; Scagliusi, S. R.; Parra, D. F.; Lugão, A. B.

2013-03-01

Foamed polymers are future materials, as they are increasingly considered "green materials" due to their interesting properties at very low consumption of raw materials. They can be used to improve appearance of insulation structures, thermal and acoustic insulation, core materials for sandwich panels, fabrication of furniture and flotation materials or to reduce costs involving materials. Low-density polyethylene is widely used because of its excellent properties, such as softness, elasticity, processibility and insulation. In general, cross-linking is often applied to improve the thermal and mechanical properties of polyethylene products, due to the formation of a three-dimensional network. In particular for the production of PE foams, cross-linking is applied prior the expansion to control bubble formation, cell characteristics and final properties of the foam. However, the usual production process of PE foams is a process in which a gaseous blowing agent is injected into a melted thermoplastic polymer, under pressure, to form a solution between blowing agent and melted polymer. An extrusion system is provided for foaming the polymer, supplied to an extruder and moving through a rotating screw. The pressure must be high enough to keep the gas blowing agent (or foaming agent) in the solution with the melt. The foaming agent is then diffused and dissolved in the molten material to form a single-phase solution. In the present work carbon dioxide was used as the bowing agent, a chemically stable and non-toxic gas, with good diffusion coefficient; gas pressure used varied within a 20-40 bar range. Some requirements for physical foaming are required, as low friction heat generation, homogeneous melt temperature distribution, melt temperature at die exit just above crystallization temperature (die) and high melt strength during expansion. This work studied foams properties gamma-irradiated within 0, 10, 15, 20, 25, and 30 kGy, from a LDPE exhibiting 2.6 g/10 min Melt Index. Accomplished tests: DSC, gel-fraction, swelling ratio in various solvents, rheological measurements, infra-red spectroscopy and melt strength. It was verified that within a given radiation dose range; the material exhibited an optimization in viscoelastic properties, providing the desired melt strength range for obtaining foams.

Cytocompatibility and response of osteoblastic-like cells to starch-based polymers: effect of several additives and processing conditions.

PubMed

Gomes, M E; Reis, R L; Cunha, A M; Blitterswijk, C A; de Bruijn, J D

2001-07-01

This work reports on the biocompatibility evaluation of new biodegradable starch-based polymers that are under consideration for use in orthopaedic temporary applications and as tissue engineering scaffolds. It has been shown in previous works that by using these polymers it is both possible to produce polymer/hydroxyapatite (HA) composites (with or without the use of coupling agents) with mechanical properties matching those of the human bone, and to obtain 3D structures generated by solid blowing agents, that are suitable for tissue engineering applications. This study was focused on establishing the influence of several additives (ceramic fillers, blowing agents and coupling agents) and processing methods/conditions on the biocompatibility of the materials described above. The cytotoxicity of the materials was evaluated using cell culture methods, according to ISO/EN 109935 guidelines. A cell suspension of human osteosarcoma cells (HOS) was also seeded on a blend of corn starch with ethylene vinyl alcohol (SEVA-C) and on SEVA-C/HA composites, in order to have a preliminary indication on cell adhesion and proliferation on the materials surface. In general, the obtained results show that all the different materials based on SEVA-C, (which are being investigated for use in several biomedical applications), as well as all the additives (including the novel coupling agents) and different processing methods required to obtain the different properties/products, can be used without inducing a cytotoxic behaviour to the developed biomaterials.

Aluminum integral foams with tailored density profile by adapted blowing agents

NASA Astrophysics Data System (ADS)

Hartmann, Johannes; Fiegl, Tobias; Körner, Carolin

2014-05-01

The goal of the present work is the variation of the structure of aluminum integral foams regarding the thickness of the integral solid skin as well as the density profile. A modified die casting process, namely integral foam molding, is used in which an aluminum melt and blowing agent particles (magnesium hydride MgH2) are injected in a permanent steel mold. The high solidification rates at the cooled walls of the mold lead to the formation of a solid skin. In the inner region, hydrogen is released by thermal decomposition of MgH2 particles. Thus, the pore formation takes place parallel to the continuing solidification of the melt. The thickness of the solid skin and the density profile of the core strongly depend on the interplay between solidification velocity and kinetics of hydrogen release. By varying the melt and blowing agent properties, the structure of integral foams can be systematically changed to meet the requirements of the desired field of application of the produced component.

Ultra low density biodegradable shape memory polymer foams with tunable physical properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singhal, Pooja; Wilson, Thomas S.; Cosgriff-Hernandez, Elizabeth

Compositions and/or structures of degradable shape memory polymers (SMPs) ranging in form from neat/unfoamed to ultra low density materials of down to 0.005 g/cc density. These materials show controllable degradation rate, actuation temperature and breadth of transitions along with high modulus and excellent shape memory behavior. A method of m ly low density foams (up to 0.005 g/cc) via use of combined chemical and physical aking extreme blowing agents, where the physical blowing agents may be a single compound or mixtures of two or more compounds, and other related methods, including of using multiple co-blowing agents of successively higher boilingmore » points in order to achieve a large range of densities for a fixed net chemical composition. Methods of optimization of the physical properties of the foams such as porosity, cell size and distribution, cell openness etc. of these materials, to further expand their uses and improve their performance.« less

Effect of air-blowing variables on bond strength of all-in-one adhesives to bovine dentin.

PubMed

Shinkai, Koichi; Suzuki, Shiro; Katoh, Yoshiroh

2006-12-01

This study evaluated the effect of air-blowing variables on the microtensile bond strength (microTBS) of two all-in-one adhesives. A bonding agent was applied to the flat dentin surface of extracted bovine teeth, and the surface left undisturbed for 20 seconds. Gentle or intensive air-blowing was applied for five seconds, and the adhesive photopolymerized for 10 seconds. Resin composite paste was placed and cured after each bonding treatment. Specimens were subjected to microTBS test with a crosshead speed of 1.0 mm/min. Data were statistically analyzed using ANOVA, followed by Bonferroni post hoc test. When Clearfil tri-S Bond was bonded to dentin, the microTBS value of specimens applied with intensive air-blowing was significantly higher than that applied with gentle air-blowing (p<0.01). On the other hand, with Fluoro Bond Shake One, the microTBS value of specimens applied with intensive air-blowing was significantly lower than that applied with gentle air-blowing (p<0.01).

Computational Investigation of Tangential Slot Blowing on a Generic Chined Forebody

NASA Technical Reports Server (NTRS)

Agosta-Greenman, Roxana M.; Gee, Ken; Cummings, Russell M.; Schiff, Lewis B.

1995-01-01

The effect of tangential slot blowing on the flowfield about a generic chined forebody at high angles of attack is investigated numerically using solutions of the thin-layer, Reynolds-averaged, Navier-Stokes equations. The effects of jet mass now ratios, angle of attack, and blowing slot location in the axial and circumferential directions are studied. The computed results compare well with available wind-tunnel experimental data. Computational results show that for a given mass now rate, the yawing moments generated by slot blowing increase as the body angle of attack increases. It is observed that greater changes in the yawing moments are produced by a slot located closest to the lip of the nose. Also, computational solutions show that inboard blowing across the top surface is more effective at generating yawing moments than blowing outboard from the bottom surface.

High temperature adhesive silicone foam composition, foam generating system and method of generating foam

DOEpatents

Mead, Judith W.; Montoya, Orelio J.; Rand, Peter B.; Willan, Vernon O.

1984-01-01

Access to a space is impeded by generation of a sticky foam from a silicone polymer and a low boiling solvent such as a halogenated hydrocarbon. In a preferred aspect, the formulation is polydimethylsiloxane gel mixed with F502 Freon as a solvent and blowing agent, and pressurized with CO.sub.2 in a vessel to about 250 PSI, whereby when the vessel is opened, a sticky and solvent resistant foam is deployed. The foam is deployable, over a wide range of temperatures, adhering to wet surfaces as well as dry, is stable over long periods of time and does not propagate flame or lose adhesive properties during an externally supported burn.

Fabrication of superhydrophobic film by microcellular plastic foaming method

NASA Astrophysics Data System (ADS)

Zhang, Zhen Xiu; Li, Ya Nan; Xia, Lin; Ma, Zhen Guo; Xin, Zhen Xiang; Kim, Jin Kuk

2014-08-01

To solve the complicated manufacturing operation and the usage of toxic solvent problems, a simple and novel method to fabricate superhydrophobic film by surface foaming method was introduced in this paper. The superhydrophobic property of the foamed material was obtained at a contact angle >150° and a rolling angle about 8°. The foamed material can instantly generate its superhydrophobicity via peeling process. The effects of blowing agent content, foaming time and peeling rate on the foam structure and superhydrophobicity were studied.

Preparation and characterization of coating sodium trisilicate (Na2O.nSiO2) at calcium carbonate (CaCO3) for blowing agent in Mg alloy foam

NASA Astrophysics Data System (ADS)

Erryani, Aprilia; Lestari, Franciska Pramuji; Annur, Dhyah; Kartika, Ika

2018-05-01

The role of blowing agent in the manufacture of porous metal alloys is very important to produce the desired pore. The thermal stability and speed of foam formation have an effect on the resulting pore structure. In porous metal alloys, uniformity of size and pore deployment are the main determinants of the resulting alloys. The coating process of calcium carbonate (CaCO3) has been done using Sodium trisilicate solution by sol-gel method. Foaming agent was pretreated by coating SiO2 passive layer on the surface of CaCO3. This coating aims to produce a more stable blowing agent so that the foaming process can produce a more uniform pore size. The microstructure of the SiO2 passive was observed using Scanning Electron Microscope (SEM) equipped by Energy Dispersive X-Ray Spectrometer (EDS) mapping. The results showed coating CaCO3 using sodium trisilicate was successfully done creating a passive layer of SiO2 on the surface of CaCO3. By the coating process, the thermal stability of coated CaCO3 increased compared to uncoated CaCO3.

Analysis of Tangential Slot Blowing on F/A-18 Isolated Forebody

NASA Technical Reports Server (NTRS)

Gee, Ken; Rizk, Yehia M.; Schiff, Lewis B.

1995-01-01

The generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and underblowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind-tunnel and subscale wind-tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flowfield about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Evaluation of HFC 245ca and HFC 236ea as foam blowing agents

NASA Technical Reports Server (NTRS)

Sharpe, Jon; Macarthur, Doug; Kollie, Tom; Graves, Ron; Liu, Matthew; Hendriks, Robert V.

1995-01-01

Hydrochlorofluorocarbon (HCFC) 141b has been selected as the interim blowing agent for use in urethane insulations on NASA's Space Shuttle External Tank. Due to the expected limited commercial lifetime of this material, research efforts at the NASA Thermal Protection Systems Materials Research Laboratory at the Marshall Space Flight Center are now being devoted to the identification and development of alternatives with zero ozone depletion potential. Physical blowing agents identified to date have included hydrocarbons, fluorocarbons, hydrofluoroethers, and more predominantly, hydrofluorocarbons (HFCs). The majority of the HFC evaluations in industry have focused on the more readily available, low boiling candidates such as HFC 134a. Higher boiling HFC candidates that could be handled at ambient conditions and use current processing equipment would be more desirable. This paper will describe results from a research program of two such candidate HFC's performed as a cooperative effort between Martin Marietta Manned Space Systems, the U.S. Environmental Protection Agency, and Oak Ridge National Laboratories. The purpose of this effort was to perform a cursory evaluation of the developmental HFC's 245ca and 236ea as blowing agents in urethane based insulations. These two materials were selected from screening tests of 37 C2, C3, and C4 isomers based on physical properties, atmospheric lifetime, flammability, estimated toxicity, difficulty of synthesis, suitability for dual use as a refrigerant, and other factors. Solubility of the two materials in typical foam components was tested, pour foaming trials were performed, and preliminary data were gathered regarding foam insulation performance.

Foam injection molding of poly(lactic acid) with physical blowing agents

NASA Astrophysics Data System (ADS)

Pantani, R.; Sorrentino, A.; Volpe, V.; Titomanlio, G.

2014-05-01

Foam injection molding uses environmental friendly blowing agents under high pressure and temperature to produce parts having a cellular core and a compact solid skin (the so-called "structural foam"). The addition of a supercritical gas reduces the part weight and at the same time improves some physical properties of the material through the promotion of a faster crystallization; it also leads to the reduction of both the viscosity and the glass transition temperature of the polymer melt, which therefore can be injection molded adopting lower temperatures and pressures. These aspects are of extreme interest for biodegradable polymers, which often present a very narrow processing window, with the suitable processing temperatures close to the degradation conditions. In this work, foam injection molding was carried out by an instrumented molding machine, able to measure the pressure evolution in different positions along the flow-path. The material adopted was a biodegradable polymer, namely the Poly(lactic acid), PLA. The effect of a physical blowing agent (PBA) on the viscosity was measured. The density reduction and the morphology of parts obtained by different molding conditions was assessed.

Preparation and Structure Study of Water-Blown Polyurethane/RDX Gun Propellant Foams

NASA Astrophysics Data System (ADS)

Yang, Weitao; Yang, Jianxing; Zhao, Yuhua; Zhang, Yucheng

2018-01-01

Water-blown polyurethane/RDX foamed propellants were prepared using polyols and isocyanate as reactive binder system, hexogen (RDX) as energetic component, triethanolamine (TEA)/Ditin butyl dilaurate (T-12) as composite catalysts, and H2O as blowing agent. The influences of catalyst ratio, blowing agent amount, and solid filler content on the inner porous structure were studied. The results show that the balance of gel rate and cream rate that could be adjusted by catalyst ratio is a major influencing factor on porous structure of foamed propellants. When the ratio of TEA/T-12 was adjusted to 1/0.7, the morphology of the foamed propellant exhibited spherical and closed porous structure. Besides, when the water amount was increased from 0.1% to 0.5%, the pore size increased from 0.43 to 0.64 mm. The contents of RDX particles affected the cell nucleation and thus, the cell geometry. When the blowing agent amount was constant, the increased content of RDX filler led to a decreased pore size. The closed bomb test results showed that foamed propellants burned progressively in an in-depth combustion mode.

In Situ Observation of Plastic Foaming under Static Condition, Extensional Flow and Shear Flow

NASA Astrophysics Data System (ADS)

Wong, Anson Sze Tat

Traditional blowing agents (e.g., hydrochlorofluorocarbons) in plastic foaming processes has been phasing out due to environmental regulations. Plastic foaming industry is forced to employ greener alternatives (e.g., carbon dioxide, nitrogen), but their foaming processes are technologically challenging. Moreover, to improve the competitiveness of the foaming industry, it is imperative to develop a new generation of value-added plastic foams with cell structures that can be tailored to different applications. In this context, the objective of this thesis is to achieve a thorough understanding on cell nucleation and growth phenomena that determine cell structures in plastic foaming processes. The core research strategy is to develop innovative visualization systems to capture and study these phenomena. A system with accurate heating and cooling control has been developed to observe and study crystallization-induced foaming behaviors of polymers under static conditions. The cell nucleation and initial growth behavior of polymers blown with different blowing agents (nitrogen, argon and helium, and carbon dioxide-nitrogen mixtures) have also been investigated in great detail. Furthermore, two innovative systems have been developed to simulate the dynamic conditions in industrial foaming processes: one system captures a foaming process under an easily adjustable and uniform extensional strain in a high temperature and pressure environment, while the other achieves the same target, but with shear strain. Using these systems, the extensional and shear effects on bubble nucleation and initial growth processes has been investigated independently in an isolated manner, which has never been achieved previously. The effectiveness of cell nucleating agents has also been evaluated under dynamic conditions, which have led to the identification of new foaming mechanisms based on polymer-chain alignment and generation of microvoids under stress. Knowledge generated from these researches and the wide range of future studies made possible by the visualization systems will be valuable to the development of innovative plastic foaming technologies and foams.

Development of fine-celled bio-fiber composite foams using physical blowing agents and nano-particles

NASA Astrophysics Data System (ADS)

Guo, Gangjian

As one of eco-friendly bio-fibers, wood-fiber has been incorporated in plastics to make wood-fiber/plastic composites (WPC) with an increased stiffness, durability and lowered cost. However, these improvements are usually accompanied by loss in the ductility and impact strength of the composites. These shortcomings can be significantly improved by incorporating a fine-cell foam structure in the composites. This thesis presents the development of the foaming technology for the manufacture of fine-cell WPC foams with environmentally benign physical blowing agents (PBAs), and focuses on the elucidation of the fundamental foaming mechanisms and the related issues involved. One critical issue comes from the volatiles evolved from the wood-fiber during high temperature processing. The volatiles, as a blowing agent, can contribute to the foaming process. However, they lead to gross deterioration of the cell structure of WPC foams. The presence of volatiles makes foaming of WPC "a poorly understood black art". With the use of PBAs, a strategy of lowering processing temperature becomes feasible, to suppress the generation of volatiles. A series of PBA-based experiments were designed using a statistical design of experiments (DOE) technique, and were performed to establish the relationship of processing and material variables with the structure of WPC foams. Fundamental foaming behaviors for two different PBAs and two different polymer systems were identified. WPC foams with a fine-cell morphology and a desired density were successfully obtained at the optimized conditions. Another limitation for the wider application of WPC is their flammability. Innovative use of a small amount of nano-clay in WPC significantly improved the flame-retarding property of WPC, and the key issue was to achieve a high degree of exfoliation of nano-particles in the polymer matrix, to achieve a desired flammability reduction. The synergistic effects of nano-particles in foaming of WPC were identified as well.

Method of forming a foamed thermoplastic polymer

DOEpatents

Duchane, D.V.; Cash, D.L.

1984-11-21

A solid thermoplastic polymer is immersed in an immersant solution comprising a compatible carrier solvent and an infusant solution containing an incompatible liquid blowing agent for a time sufficient for the immersant solution to infuse into the polymer. The carrier solvent is then selectively extracted, preferably by a solvent exchange process in which the immersant solution is gradually diluted with and replaced by the infusant solution, so as to selectively leave behind the infustant solution permanently entrapped in the polymer. The polymer is then heated to volatilize the blowing agent and expand the polymer into a foamed state.

High temperature adhesive silicone foam composition, foam generating system and method of generating foam. [For access denial

DOEpatents

Mead, J.W.; Montoya, O.J.; Rand, P.B.; Willan, V.O.

1983-12-21

Access to a space is impeded by generation of a sticky foam from a silicone polymer and a low boiling solvent such as a halogenated hydrocarbon. In a preferred aspect, the formulation is polydimethylsiloxane gel mixed with F502 Freon as a solvent and blowing agent, and pressurized with CO/sub 2/ in a vessel to about 250 PSI, whereby when the vessel is opened, a sticky and solvent resistant foam is deployed. The foam is deployable, over a wide range of temperatures, adhering to wet surfaces as well as dry, is stable over long periods of time and does not propagate flame or lose adhesive properties during an externally supported burn.

Numerical analysis of tangential slot blowing on a generic chined forebody

NASA Technical Reports Server (NTRS)

Agosta, Roxana M.

1994-01-01

A numerical study is performed to investigate the effects of tangential slot blowing on a generic chined forebody. The Reynolds-averaged, thin-layer, Navier-Stokes equations are solved to obtain the high-angle-of-attack viscous flow field about a generic chined forebody. Tangential slot blowing is investigated as a means of forebody flow control to generate side force and yawing moment on the forebody. The effects of jet mass flow ratios, angle of attack, and blowing slot location in the axial and circumferential directions are studied. The computed results are compared with available wind tunnel experimental data. The solutions with and without blowing are also analyzed using helicity density contours, surface flow patterns, and off-surface instantaneous streamlines. The results of this analysis provide details of the flow field about the generic chined forebody, as well as show that tangential slot blowing can be used as a means of forebody flow control to generate side force and yawing moment.

Drug utilisation review (DUR) of the third generation cephalosporins. Focus on ceftriaxone, ceftazidime and cefotaxime.

PubMed

Adu, A; Armour, C L

1995-09-01

Six parenteral third generation cephalosporins have been introduced into clinical use in the past 10 years. The 3 most frequently available agents are cefotaxime, ceftriaxone and ceftazidime. These 3 third generation cephalosporins are characterised by a broad spectrum of activity and increased stability to beta-lactamases compared with the first and second generation cephalosporins. However, there are growing numbers of reports of resistance to these agents with increasing use. The major differences in the properties of the 3 agents are the long half-life of ceftriaxone and its dual route of elimination. Ceftazidime is best restricted to Pseudomonas aeruginosa infections where other agents are contraindicated or ineffective. Cefotaxime and ceftriaxone can be used in nosocomial Gram-negative infections where P. aeruginosa can be ruled out. The types and incidences of adverse drug reactions are not different for the 3 agents. A number of drug utilisation review (DUR) studies of these agents in the hospital setting have reported a considerable incidence of inappropriate use and substantial avoidable costs. There are methodological problems with most of the DUR studies, especially the criteria and the methods of cost estimation. The use of pharmacoeconomic methodology could ensure more realistic cost estimation; however, outcome data are, in most cases, not available.

Development of Mechanistic Reasoning and Multilevel Explanations of Ecology in Third Grade Using Agent-Based Models

ERIC Educational Resources Information Center

Dickes, Amanda Catherine; Sengupta, Pratim; Farris, Amy Voss; Satabdi, Basu

2016-01-01

In this paper, we present a third-grade ecology learning environment that integrates two forms of modeling--embodied modeling and agent-based modeling (ABMs)--through the generation of mathematical representations that are common to both forms of modeling. The term "agent" in the context of ABMs indicates individual computational objects…

Short- and long-term releases of fluorocarbons from disposal of polyurethane foam waste.

PubMed

Kjeldsen, Peter; Scheutz, Charlotte

2003-11-01

Several halocarbons having very high global warming or ozone depletion potentials have been used as a blowing agent (BA) for insulation foam in home appliances, such as refrigerators and freezers. Many appliances are shredded after the end of their useful life. Release experiments carried out in the laboratory on insulation foam blown with the blowing agents CFC-11, HCFC-141b, HCF-134fa, and HFC-245fa revealed that not all blowing agents are released during a 6-week period following the shredding process. The experiments confirmed the hypothesis that the release could be divided into three segments: By shredding foam panels, a proportion of the closed cells is either split or damaged to a degree allowing for a sudden release of the contained atmosphere in the cell (the instantaneous release). Cells adjacent to the cut surface may be only slightly damaged by tiny cracks or holes allowing a relative slow release of the BA to the surroundings (the short-term release). A significant portion of the cells in the foam particle will be unaffected and only allows release governed by slow diffusion through the PUR cell wall (the long-term release). The magnitude of the releases is for all three types highly dependent on how fine the foam is shredded. The residual blowing agent remaining after the 6-week period may be very slowly released if the integrity of the foam particles with respect to diffusion properties is kept after disposal of the foam waste on landfills. It is shown by setting up a national model simulating the BA releases following decommissioning of used domestic refrigerators/freezers in the United States that the release patterns are highly dependent on how the appliances are shredded.

Method of forming a foamed thermoplastic polymer

DOEpatents

Duchane, David V.; Cash, David L.

1986-01-01

A method of forming a foamed thermoplastic polymer. A solid thermoplastic lymer is immersed in an immersant solution comprising a compatible carrier solvent and an infusant solution containing an incompatible liquid blowing agent for a time sufficient for the immersant solution to infuse into the polymer. The carrier solvent is then selectively extracted, preferably by a solvent exchange process in which the immersant solution is gradually diluted with and replaced by the infusant solution, so as to selectively leave behind the infusant solution permanently entrapped in the polymer. The polymer is then heated to volatilize the blowing agent and expand the polymer into a foamed state.

Method for producing small hollow spheres

DOEpatents

Hendricks, C.D.

1979-01-09

Method is disclosed for producing small hollow spheres of glass, metal or plastic, wherein the sphere material is mixed with or contains as part of the composition a blowing agent which decomposes at high temperature (T [approx gt] 600 C). As the temperature is quickly raised, the blowing agent decomposes and the resulting gas expands from within, thus forming a hollow sphere of controllable thickness. The thus produced hollow spheres (20 to 10[sup 3] [mu]m) have a variety of application, and are particularly useful in the fabrication of targets for laser implosion such as neutron sources, laser fusion physics studies, and laser initiated fusion power plants. 1 fig.

Method and apparatus for producing small hollow spheres

DOEpatents

Hendricks, Charles D.

1979-01-01

Method and apparatus for producing small hollow spheres of glass, metal or plastic, wherein the sphere material is mixed with or contains as part of the composition a blowing agent which decomposes at high temperature (T.gtoreq.600.degree. C.). As the temperature is quickly raised, the blowing agent decomposes and the resulting gas expands from within, thus forming a hollow sphere of controllable thickness. The thus produced hollow spheres (20 to 10.sup.3 .mu.m) have a variety of application, and are particularly useful in the fabrication of targets for laser implosion such as neutron sources, laser fusion physics studies, and laser initiated fusion power plants.

Method for producing small hollow spheres

DOEpatents

Hendricks, Charles D. [Livermore, CA

1979-01-09

Method for producing small hollow spheres of glass, metal or plastic, wherein the sphere material is mixed with or contains as part of the composition a blowing agent which decomposes at high temperature (T .gtorsim. 600.degree. C). As the temperature is quickly raised, the blowing agent decomposes and the resulting gas expands from within, thus forming a hollow sphere of controllable thickness. The thus produced hollow spheres (20 to 10.sup.3 .mu.m) have a variety of application, and are particularly useful in the fabrication of targets for laser implosion such as neutron sources, laser fusion physics studies, and laser initiated fusion power plants.

Polyurethane Foams for Thermal Insulation Uses Produced from Castor Oil and Crude Glycerol Biopolyols.

PubMed

Carriço, Camila S; Fraga, Thaís; Carvalho, Vagner E; Pasa, Vânya M D

2017-07-02

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst (DBTDL) content and blowing agents in the foams' properties were evaluated. The use of physical blowing agents (cyclopentane and n-pentane) allowed foams with smaller cells to be obtained in comparison with the foams produced with a chemical blowing agent (water). The increase of the water content caused a decrease in density, thermal conductivity, compressive strength, and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amounts of catalyst in the foam formulations caused a slight density decrease and a small increase of thermal conductivity, compressive strength, and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation: density (23-41 kg·m -3 ), thermal conductivity (0.0128-0.0207 W·m -1 ·K -1 ), compressive strength (45-188 kPa), and Young's modulus (3-28 kPa). These biofoams are also environmentally friendly polymers and can aggregate revenue to the biodiesel industry, contributing to a reduction in fuel prices.

Convective Ignition of Propellant Cylinders in a Developing Cross-Flow Field.

DTIC Science & Technology

1980-09-01

Ignition. .. ...... ..... 69 (ii) Polymer Ignition .. ....... ....... 72 F . Flame Spreading and Blow -off Phenomena .. ...... 72 G. Ignition and Flame...polymeric fuel binder for mechanical integrity. It also includes solid additives (like aluminum) and various catalysts and plasticizing agents . Ballistic...placed on distinguishing the ignition sites and the flame spreading (and blow off) tendencies as functions of the external flow velocity pressure and

Crosslinked polyethylene foams, via EB radiation

NASA Astrophysics Data System (ADS)

Cardoso, E. C. L.; Lugão, A. B.; Andrade E. Silva, L. G.

1998-06-01

Polyethylene foams, produced by radio-induced crosslinking, show a smooth and homogeneous surface, when compared to chemical crosslinking method using peroxide as crosslinking agent. This process fosters excellent adhesive and printability properties. Besides that, closed cells, intrinsic to theses foams, imparts opitmum mechanical, shocks and insulation resistance, indicating these foams to some markets segments as: automotive and transport; buoyancy, flotation and marine: building and insulation: packaging: domestic sports and leisure goods. We were in search of an ideal foam, by adding 5 to 15% of blowing agent in LDPE. A series of preliminary trials defined 203° C as the right blowing agent decomposition temperature. At a 22.7 kGy/dose ratio, the lowest dose for providing an efficient foam was 30 kGy, for a formulation comprising 10% of azodicarbonamide in LDPE, within a 10 minutes foaming time.

IRIS TOXICOLOGICAL REVIEW AND SUMMARY DOCUMENTS FOR CHLOROETHANE (EXTERNAL REVIEW DRAFT)

EPA Science Inventory

Chloroethane (CE) is a gaseous halohydrocarbon under ambient conditions. Its uses include: a topical analgesic, an anesthetic when mixed with nitrous dioxide or trichloroethane, a degreasing agent, and an agent to blow styrene in foaming operations. Anecdotal human reports indica...

Deformation behavior of open-cell dry natural rubber foam: Effect of different concentration of blowing agent and compression strain rate

NASA Astrophysics Data System (ADS)

Samsudin, M. S. F.; Ariff, Z. M.; Ariffin, A.

2017-04-01

Compression and deformation behavior of partially open cell natural rubber (NR) foam produced from dry natural rubber (DNR), were investigated by performing compressive deformation at different strains and strain rates. Different concentrations of sodium bicarbonate as a blowing agent (BA) were utilized, from 4 to 16 phr in order to produce foams with range of cell size and morphology. Overall, increasing of blowing agent concentration had significantly changed relative foam density. Compression stress-strain curves of the foams exhibited that the compression behavior was directly correlated to the foam cells morphology and physical density. Pronounced changes were noticed for foams with bigger cells particularly at 4 phr concentration of BA where the compression stress at plateau region was greater compared to those with higher concentration of BA. Cell deformation progressive images confirmed that the foams demonstrated small degree of struts bending at 15% of strain and followed by continuous severe struts bending and elastic buckling up to 50% of strain. Compression test at different strain rates revealed that the strain rate factor only affected the foams with 4 phr of BA by causing immediate increment in the compression stress value when higher strain rate was applied.

Forebody tangential blowing for control at high angles of attack

NASA Technical Reports Server (NTRS)

Kroo, I.; Rock, S.; Roberts, L.

1991-01-01

A feasibility study to determine if the use of tangential leading edge blowing over the forebody could produce effective and practical control of the F-18 HARV aircraft at high angles of attack was conducted. A simplified model of the F-18 configuration using a vortex-lattice model was developed to obtain a better understanding of basic aerodynamic coupling effects and the influence of forebody circulation on lifting surface behavior. The effect of tangential blowing was estimated using existing wind tunnel data on normal forebody blowing and analytical studies of tangential blowing over conical forebodies. Incorporation of forebody blowing into the flight control system was investigated by adding this additional yaw control and sideforce generating actuator into the existing F-18 HARV simulation model. A control law was synthesized using LQG design methods that would schedule blowing rates as a function of vehicle sideslip, angle of attack, and roll and yaw rates.

Computational analysis of forebody tangential slot blowing on the high alpha research vehicle

NASA Technical Reports Server (NTRS)

Gee, Ken

1994-01-01

Current and future fighter aircraft can maneuver in the high-angle-of-attack flight regime while flying at low subsonic and transonic freestream Mach numbers. However, at any flight speed, the ability of the vertical tails to generate yawing moment is limited in high-angle-of-attack flight. Thus, any system designed to provide the pilot with additional side force and yawing moment must work in both low subsonic and transonic flight. However, previous investigations of the effectiveness of forebody tangential slot blowing in generating the desired control forces and moments have been limited to the low subsonic freestream flow regime. In order to investigate the effectiveness of tangential slot blowing in transonic flight, a computational fluid dynamics analysis was carried out during the grant period. Computational solutions were obtained at three different freestream Mach numbers and at various jet mass flow ratios. All results were obtained using the isolated F/A-18 forebody grid geometry at 30.3 degrees angle of attack. One goal of the research was to determine the effect of freestream Mach number on the effectiveness of forebody tangential slot blowing in generating yawing moment. The second part of the research studied the force onset time lag associated with blowing. The time required for the yawing moment to reach a steady-state value from the onset of blowing may have an impact on the implementation of a pneumatic system on a flight vehicle.

KOVATS RETENTION INDICES OF HALOCARBONS ON A HEXAFLUOROPROPYLENE EPOXIDE-MODIFIED GRAPHITIZED CARBON BLACK

EPA Science Inventory

The article gives results of measuring Kovats retention indices of 97 halocarbons related to research on alternative refrigerants, propellants, foaming agents, and blowing agents, on a packed-column stationary phase consisting of a 5% mass coating of a low-molecular-weight polyme...

Static and wind tunnel model tests for the development of externally blown flap noise reduction techniques

NASA Technical Reports Server (NTRS)

Pennock, A. P.; Swift, G.; Marbert, J. A.

1975-01-01

Externally blown flap models were tested for noise and performance at one-fifth scale in a static facility and at one-tenth scale in a large acoustically-treated wind tunnel. The static tests covered two flap designs, conical and ejector nozzles, third-flap noise-reduction treatments, internal blowing, and flap/nozzle geometry variations. The wind tunnel variables were triple-slotted or single-slotted flaps, sweep angle, and solid or perforated third flap. The static test program showed the following noise reductions at takeoff: 1.5 PNdB due to treating the third flap; 0.5 PNdB due to blowing from the third flap; 6 PNdB at flyover and 4.5 PNdB in the critical sideline plane (30 deg elevation) due to installation of the ejector nozzle. The wind tunnel program showed a reduction of 2 PNdB in the sideline plane due to a forward speed of 43.8 m/s (85 kn). The best combination of noise reduction concepts reduced the sideline noise of the reference aircraft at constant field length by 4 PNdB.

Self-Calibrating, Variable-Flow Pumping System

NASA Technical Reports Server (NTRS)

Walls, Joe T.

1994-01-01

Pumping system provides accurate, controlled flows of two chemical liquids mixed in spray head and react to form rigid or flexible polyurethane or polyisocyanurate foam. Compatible with currently used polyurethane-based coating materials and gas-bubble-forming agents (called "blowing agents" in industry) and expected to be compatible with materials that used in near future. Handles environmentally acceptable substitutes for chlorofluorocarbon foaming agents.

Hollow spherical shell manufacture

DOEpatents

O'Holleran, T.P.

1991-11-26

A process is disclosed for making a hollow spherical shell of silicate glass composition in which an aqueous suspension of silicate glass particles and an immiscible liquid blowing agent is placed within the hollow spherical cavity of a porous mold. The mold is spun to reduce effective gravity to zero and to center the blowing agent, while being heated so as to vaporize the immiscible liquid and urge the water carrier of the aqueous suspension to migrate into the body of the mold, leaving a green shell compact deposited around the mold cavity. The green shell compact is then removed from the cavity, and is sintered for a time and a temperature sufficient to form a silicate glass shell of substantially homogeneous composition and uniform geometry. 3 figures.

Hollow spherical shell manufacture

DOEpatents

O'Holleran, Thomas P.

1991-01-01

A process for making a hollow spherical shell of silicate glass composition in which an aqueous suspension of silicate glass particles and an immiscible liquid blowing agent is placed within the hollow spherical cavity of a porous mold. The mold is spun to reduce effective gravity to zero and to center the blowing agent, while being heated so as to vaporize the immiscible liquid and urge the water carrier of the aqueous suspension to migrate into the body of the mold, leaving a green shell compact deposited around the mold cavity. The green shell compact is then removed from the cavity, and is sintered for a time and a temperature sufficient to form a silicate glass shell of substantially homogeneous composition and uniform geometry.

Environmental risk assessment of hydrofluoroethers (HFEs).

PubMed

Tsai, Wen-Tien

2005-03-17

Hydrofluoroethers (HFEs) are being used as third generation replacements to chlorofluorocarbons (CFCs), hydrochlorofluorocarbons (HCFCs) and perfluorocarbons (PFCs) because of their nearly zero stratospheric ozone depletion and relatively low global warming potential. HFEs have been developed under commercial uses as cleaning solvents (incl., HFE-7500, C7F15OC2H5; HFE-7200, C4F9OC2H5; HFE-7100, C4F9CH3; HFE-7000, n-C3F7OCH3), blowing agents (incl., HFE-245mc, CF3CF2OCH3; HFC-356mec, CF3CHFCF2OCH3), refrigerants (incl., HFE-143a, CF3OCH3; HFE-134, CHF2OCHF2; HFE-245mc, CF3CF2OCH3), and dry etching agents in semiconductor manufacturing, (incl., HFE-227me, CF3OCHFCF3). From the environmental, ecological, and health points of view, it is important to understand their environmental risks for these HFEs from a diversity of commercial applications and industrial processes. This paper aims to introduce these HFEs with respect to physiochemical properties, commercial uses, and environmental hazards (i.e. global warming, photochemical potential, fire and explosion hazard, and environmental partition). Further, it addresses the updated data on the human toxicity, occupational exposure and potential health risk of commercial HFEs. It is concluded that there are few HFEs that still possess some environmental hazards, including global warming, flammability hazard and adverse effect of exposure. The partition coefficient for these HFEs has been estimated using the group contribution method; the values of logKow for commercial HFEs have been estimated to be below 3.5.

Lithic Scatters that Blow: Wind as an Agent of Secondary Deposition of Lithic Artifacts

USDA-ARS?s Scientific Manuscript database

Artifact presence or absence is frequently the only criteria used to define the horizontal extent of archaeological sites. Artifact transport by natural agents such as water and gravity is known to move artifacts from their primary context, though experimental simulated wind conditions demonstrate t...

Ultrasound contrast agent fabricated from microbubbles containing instant adhesives, and its ultrasound imaging ability

NASA Astrophysics Data System (ADS)

Makuta, T.; Tamakawa, Y.

2012-04-01

Non-invasive surgery techniques and drug delivery system with acoustic characteristics of ultrasound contrast agent have been studied intensively in recent years. Ultrasound contrast agent collapses easily under the blood circulating and the ultrasound irradiating because it is just a stabilized bubble without solid-shell by surface adsorption of surfactant or lipid. For improving the imaging stability, we proposed the fabrication method of the hollow microcapsule with polymer shell, which can be fabricated just blowing vapor of commonly-used instant adhesive (Cyanoacrylate monomer) into water as microbubbles. Therefore, the cyanoacrylate vapor contained inside microbubble initiates polymerization on the gasliquid interface soon after microbubbles are generated in water. Consequently, hollow microspheres coated by cyanoacrylate thin film are generated. In this report, we revealed that diameter distributions of microbubbles and microcapsules were approximately same and most of them were less than 10 μm, that is, smaller than blood capillary. In addition, we also revealed that hollow microcapsules enhanced the acoustic signal especially in the harmonic contrast imaging and were broken or agglomerated under the ultrasound field. As for the yield of hollow microcapsules, we revealed that sodium dodecyl sulfate addition to water phase instead of deoxycolic acid made the fabrication yield increased.

Blowing snow detection from ground-based ceilometers: application to East Antarctica

NASA Astrophysics Data System (ADS)

Gossart, Alexandra; Souverijns, Niels; Gorodetskaya, Irina V.; Lhermitte, Stef; Lenaerts, Jan T. M.; Schween, Jan H.; Mangold, Alexander; Laffineur, Quentin; van Lipzig, Nicole P. M.

2017-12-01

Blowing snow impacts Antarctic ice sheet surface mass balance by snow redistribution and sublimation. However, numerical models poorly represent blowing snow processes, while direct observations are limited in space and time. Satellite retrieval of blowing snow is hindered by clouds and only the strongest events are considered. Here, we develop a blowing snow detection (BSD) algorithm for ground-based remote-sensing ceilometers in polar regions and apply it to ceilometers at Neumayer III and Princess Elisabeth (PE) stations, East Antarctica. The algorithm is able to detect (heavy) blowing snow layers reaching 30 m height. Results show that 78 % of the detected events are in agreement with visual observations at Neumayer III station. The BSD algorithm detects heavy blowing snow 36 % of the time at Neumayer (2011-2015) and 13 % at PE station (2010-2016). Blowing snow occurrence peaks during the austral winter and shows around 5 % interannual variability. The BSD algorithm is capable of detecting blowing snow both lifted from the ground and occurring during precipitation, which is an added value since results indicate that 92 % of the blowing snow is during synoptic events, often combined with precipitation. Analysis of atmospheric meteorological variables shows that blowing snow occurrence strongly depends on fresh snow availability in addition to wind speed. This finding challenges the commonly used parametrizations, where the threshold for snow particles to be lifted is a function of wind speed only. Blowing snow occurs predominantly during storms and overcast conditions, shortly after precipitation events, and can reach up to 1300 m a. g. l. in the case of heavy mixed events (precipitation and blowing snow together). These results suggest that synoptic conditions play an important role in generating blowing snow events and that fresh snow availability should be considered in determining the blowing snow onset.

Mesoporous hollow spheres from soap bubbling.

PubMed

Yu, Xianglin; Liang, Fuxin; Liu, Jiguang; Lu, Yunfeng; Yang, Zhenzhong

2012-02-01

The smaller and more stable bubbles can be generated from the large parent bubbles by rupture. In the presence of a bubble blowing agent, hollow spheres can be prepared by bubbling a silica sol. Herein, the trapped gas inside the bubble acts as a template. When the porogen, i.e., other surfactant, is introduced, a mesostructured shell forms by the co-assembly with the silica sol during sol-gel process. Morphological evolution emphasizes the prerequisite of an intermediate interior gas flow rate and high exterior gas flow rate for hollow spheres. The method is valid for many compositions from inorganic, polymer to their composites. Copyright © 2011 Elsevier Inc. All rights reserved.

Building intelligence in third-generation training and battle simulations

NASA Astrophysics Data System (ADS)

Jacobi, Dennis; Anderson, Don; von Borries, Vance; Elmaghraby, Adel; Kantardzic, Mehmed; Ragade, Rammohan

2003-09-01

Current war games and simulations are primarily attrition based, and are centered on the concept of force on force. They constitute what can be defined as "second generation" war games. So-called "first generation" war games were focused on strategy with the primary concept of mind on mind. We envision "third generation" war games and battle simulations as concentrating on effects with the primary concept being system on system. Thus the third generation systems will incorporate each successive generation and take into account strategy, attrition and effects. This paper will describe the principal advantages and features that need to be implemented to create a true "third generation" battle simulation and the architectural issues faced when designing and building such a system. Areas of primary concern are doctrine, command and control, allied and coalition warfare, and cascading effects. Effectively addressing the interactive effects of these issues is of critical importance. In order to provide an adaptable and modular system that will accept future modifications and additions with relative ease, we are researching the use of a distributed Multi-Agent System (MAS) that incorporates various artificial intelligence methods. The agent architecture can mirror the military command structure from both vertical and horizontal perspectives while providing the ability to make modifications to doctrine, command structures, inter-command communications, as well as model the results of various effects upon one another, and upon the components of the simulation. This is commonly referred to as "cascading effects," in which A affects B, B affects C and so on. Agents can be used to simulate units or parts of units that interact to form the whole. Even individuals can eventually be simulated to take into account the affect to key individuals such as commanders, heroes, and aces. Each agent will have a learning component built in to provide "individual intelligence" based on experience.

46 CFR 31.10-18 - Firefighting equipment: General-TB/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... extinguishing agent is needed. Carbon dioxide Weigh cylinders. Recharge if weight loss exceeds 10 percent of... ascertain that the system is in good operating condition. For carbon dioxide or clean agent systems as... be tested with at least 50 pounds per square inch of air pressure or by blowing steam through the...

46 CFR 31.10-18 - Firefighting equipment: General-TB/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... extinguishing agent is needed. Carbon dioxide Weigh cylinders. Recharge if weight loss exceeds 10 percent of... ascertain that the system is in good operating condition. For carbon dioxide or clean agent systems as... be tested with at least 50 pounds per square inch of air pressure or by blowing steam through the...

Distributed Blowing and Suction for the Purpose of Streak Control in a Boundary Layer Subjected to a Favorable Pressure Gradient

NASA Technical Reports Server (NTRS)

Forgoston, Eric; Tumin, Anatoli; Ashpis, David E.

2005-01-01

An analysis of the optimal control by blowing and suction in order to generate stream- wise velocity streaks is presented. The problem is examined using an iterative process that employs the Parabolized Stability Equations for an incompressible uid along with its adjoint equations. In particular, distributions of blowing and suction are computed for both the normal and tangential velocity perturbations for various choices of parameters.

Computational analysis of forebody tangential slot blowing

NASA Technical Reports Server (NTRS)

Gee, Ken; Agosta-Greenman, Roxana M.; Rizk, Yehia M.; Schiff, Lewis B.; Cummings, Russell M.

1994-01-01

An overview of the computational effort to analyze forebody tangential slot blowing is presented. Tangential slot blowing generates side force and yawing moment which may be used to control an aircraft flying at high-angle-of-attack. Two different geometries are used in the analysis: (1) The High Alpha Research Vehicle; and (2) a generic chined forebody. Computations using the isolated F/A-18 forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of over- and under-blowing on force and moment production are analyzed. Time-accurate solutions using the isolated forebody are obtained to study the force onset timelag of tangential slot blowing. Computations using the generic chined forebody are obtained at experimental wind tunnel conditions, and the results compared with available experimental data. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about simple and complex geometries.

Applying tattoo dye as a third-harmonic generation contrast agent for in vivo optical virtual biopsy of human skin

NASA Astrophysics Data System (ADS)

Tsai, Ming-Rung; Lin, Chen-Yu; Liao, Yi-Hua; Sun, Chi-Kuang

2013-02-01

Third-harmonic generation (THG) microscopy has been reported to provide intrinsic contrast in elastic fibers, cytoplasmic membrane, nucleus, actin filaments, lipid bodies, hemoglobin, and melanin in human skin. For advanced molecular imaging, exogenous contrast agents are developed for a higher structural or molecular specificity. We demonstrate the potential of the commonly adopted tattoo dye as a THG contrast agent for in vivo optical biopsy of human skin. Spectroscopy and microscopy experiments were performed on cultured cells with tattoo dyes, in tattooed mouse skin, and in tattooed human skin to demonstrate the THG enhancement effect. Compared with other absorbing dyes or nanoparticles used as exogenous THG contrast agents, tattoo dyes are widely adopted in human skin so that future clinical biocompatibility evaluation is relatively achievable. Combined with the demonstrated THG enhancement effect, tattoo dyes show their promise for future clinical imaging applications.

9 CFR 147.24 - Cleaning and disinfecting.

Code of Federal Regulations, 2012 CFR

2012-01-01

... houses: (1) Remove all live “escaped” and dead birds from the building. Blow dust from equipment and...) Use cleaning agents and sanitizers that are registered by the U.S. Environmental Protection Agency as...

9 CFR 147.24 - Cleaning and disinfecting.

Code of Federal Regulations, 2013 CFR

2013-01-01

... houses: (1) Remove all live “escaped” and dead birds from the building. Blow dust from equipment and...) Use cleaning agents and sanitizers that are registered by the U.S. Environmental Protection Agency as...

9 CFR 147.24 - Cleaning and disinfecting.

Code of Federal Regulations, 2014 CFR

2014-01-01

... houses: (1) Remove all live “escaped” and dead birds from the building. Blow dust from equipment and...) Use cleaning agents and sanitizers that are registered by the U.S. Environmental Protection Agency as...

9 CFR 147.24 - Cleaning and disinfecting.

Code of Federal Regulations, 2011 CFR

2011-01-01

... houses: (1) Remove all live “escaped” and dead birds from the building. Blow dust from equipment and...) Use cleaning agents and sanitizers that are registered by the U.S. Environmental Protection Agency as...

Wind Texture

NASA Image and Video Library

2010-11-10

One of the most active agent of erosion on Mars today is the wind. This region, near Nicholson crater, has been sculpted by untold years of blowing grit and wind, as shown in this image captured by NASA Mars Odyssey.

Transitioning to Low-GWP Alternatives in Transport Refrigeration

EPA Pesticide Factsheets

This fact sheet provides information on low-GWP refrigerant and foam blowing agent alternatives used in transport refrigeration equipment. It discusses HFC alternatives, market trends, challenges to market entry for alternatives, and potential solutions.

Phenol-formaldehyde intumescent coating composition and coating prepared therefrom

NASA Technical Reports Server (NTRS)

Salyer, Ival O. (Inventor); Fox, Bernard L. (Inventor)

1986-01-01

Intumescent coatings which form a thick, uniform, fine celled, low density foam upon exposure to a high intensity heat flux or flame are disclosed, the invention coatings comprise phenolic resin prepolymer containing a blowing agent and a nucleating agent; in the preferred embodiments the coatings also contains a silicone surfactant, the coatings are useful in thermal and fire protection systems.

Active Control of Flow Separation Over an Airfoil

NASA Technical Reports Server (NTRS)

Ravindran, S. S.

1999-01-01

Designing an aircraft without conventional control surfaces is of interest to aerospace community. In this direction, smart actuator devices such as synthetic jets have been proposed to provide aircraft maneuverability instead of control surfaces. In this article, a numerical study is performed to investigate the effects of unsteady suction and blowing on airfoils. The unsteady suction and blowing is introduced at the leading edge of the airfoil in the form of tangential jet. Numerical solutions are obtained using Reynolds-Averaged viscous compressible Navier-Stokes equations. Unsteady suction and blowing is investigated as a means of separation control to obtain lift on airfoils. The effect of blowing coefficients on lift and drag is investigated. The numerical simulations are compared with experiments from the Tel-Aviv University (TAU). These results indicate that unsteady suction and blowing can be used as a means of separation control to generate lift on airfoils.

Gene expression during blow fly development: improving the precision of age estimates in forensic entomology.

PubMed

Tarone, Aaron M; Foran, David R

2011-01-01

Forensic entomologists use size and developmental stage to estimate blow fly age, and from those, a postmortem interval. Since such estimates are generally accurate but often lack precision, particularly in the older developmental stages, alternative aging methods would be advantageous. Presented here is a means of incorporating developmentally regulated gene expression levels into traditional stage and size data, with a goal of more precisely estimating developmental age of immature Lucilia sericata. Generalized additive models of development showed improved statistical support compared to models that did not include gene expression data, resulting in an increase in estimate precision, especially for postfeeding third instars and pupae. The models were then used to make blind estimates of development for 86 immature L. sericata raised on rat carcasses. Overall, inclusion of gene expression data resulted in increased precision in aging blow flies. © 2010 American Academy of Forensic Sciences.

Numerical study of the trailing vortex of a wing with wing-tip blowing

NASA Technical Reports Server (NTRS)

Lim, Hock-Bin

1994-01-01

Trailing vortices generated by lifting surfaces such as helicopter rotor blades, ship propellers, fixed wings, and canard control surfaces are known to be the source of noise, vibration, cavitation, degradation of performance, and other hazardous problems. Controlling these vortices is, therefore, of practical interest. The formation and behavior of the trailing vortices are studied in the present research. In addition, wing-tip blowing concepts employing axial blowing and spanwise blowing are studied to determine their effectiveness in controlling these vortices and their effects on the performance of the wing. The 3D, unsteady, thin-layer compressible Navier-Stokes equations are solved using a time-accurate, implicit, finite difference scheme that employs LU-ADI factorization. The wing-tip blowing is simulated using the actuator plane concept, thereby, not requiring resolution of the jet slot geometry. Furthermore, the solution blanking feature of the chimera scheme is used to simplify the parametric study procedure for the wing-tip blowing. Computed results are shown to compare favorably with experimental measurements. It is found that axial wing-tip blowing, although delaying the rolling-up of the trailing vortices and the near-field behavior of the flowfield, does not dissipate the circulation strength of the trailing vortex farther downstream. Spanwise wing-tip blowing has the effect of displacing the trailing vortices outboard and upward. The increased 'wing-span' due to the spanwise wing-tip blowing has the effect of lift augmentation on the wing and the strengthening of the trailing vortices. Secondary trailing vortices are created at high spanwise wing-tip blowing intensities.

Quest for Efficacious Next-Generation Taxoid Anticancer Agents and Their Tumor-Targeted Delivery

PubMed Central

2018-01-01

Paclitaxel and docetaxel are among the most widely used chemotherapeutic drugs against various types of cancer. However, these drugs cause undesirable side effects as well as drug resistance. Therefore, it is essential to develop next-generation taxoid anticancer agents with better pharmacological properties and improved activity especially against drug-resistant and metastatic cancers. The SAR studies by the authors have led to the development of numerous highly potent novel second- and third-generation taxoids with systematic modifications at the C-2, C-10, and C-3′ positions. The third-generation taxoids showed virtually no difference in potency against drug-resistant and drug-sensitive cell lines. Some of the next-generation taxoids also exhibited excellent potency against cancer stem cells. This account summarizes concisely investigations into taxoids over 25 years based on a strong quest for the discovery and development of efficacious next-generation taxoids. Discussed herein are SAR studies on different types of taxoids, a common pharmacophore proposal for microtubule-stabilizing anticancer agents and its interesting history, the identification of the paclitaxel binding site and its bioactive conformation, characteristics of the next-generation taxoids in cancer cell biology, including new aspects of their mechanism of action, and the highly efficacious tumor-targeted drug delivery of potent next-generation taxoids. PMID:29468872

Presidential Green Chemistry Challenge: 1996 Greener Reaction Conditions Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 1996 award winner, Dow Chemical Company, developed a process to manufacture polystyrene foam sheet packaging that uses carbon dioxide (CO2) as a blowing agent, eliminating CFC-12 and HCFC-22.

Morphologies, Processing and Properties of Ceramic Foams from Pre-Ceramic Foams from Pre-Ceramic Polymer Routes

NASA Technical Reports Server (NTRS)

Stackpoole, Mairead; Simoes, Conan R.; Venkatapathy, Ethiras (Technical Monitor)

2002-01-01

The current research is focused on processing ceramic foams that have potential as a thermal protection material. Ceramic foams with different architectures were formed from the pyrolysis of pre-ceramic polymers at 1200 C in different atmospheres. In some systems a sacrificial polyurethane was used as the blowing agent. We have also processed foams using sacrificial fillers to introduce controlled cell sizes. Each sacrificial filler or blowing agent leads to a unique morphology. The effect of different fillers on foam morphologies will be presented. The presentation will also focus on characterization of these foams in terms of mechanical and thermal properties. Foams processed using these approaches having bulk densities ranging from 0.15 to 0.9 g per cubic centimeter and a cell sizes from 5 to 500 micrometers. Compression strengths ranged from 2 to 7 MPa for these materials.

Advances in self-healing materials based on vascular networks with mechanical self-repair characteristics.

PubMed

Lee, Min Wook; An, Seongpil; Yoon, Sam S; Yarin, Alexander L

2018-02-01

Here, we review the state-of-the-art in the field of engineered self-healing materials. These materials mimic the functionalities of various natural materials found in the human body (e.g., the healing of skin and bones by the vascular system). The fabrication methods used to produce these "vascular-system-like" engineered self-healing materials, such as electrospinning (including co-electrospinning and emulsion spinning) and solution blowing (including coaxial solution blowing and emulsion blowing) are discussed in detail. Further, a few other approaches involving the use of hollow fibers are also described. In addition, various currently used healing materials/agents, such as dicyclopentadiene and Grubbs' catalyst, poly(dimethyl siloxane), and bisphenol-A-based epoxy, are described. We also review the characterization methods employed to verify the physical and chemical aspects of self-healing, that is, the methods used to confirm that the healing agent has been released and that it has resulted in healing, as well as the morphological changes induced in the damaged material by the healing agent. These characterization methods include different visualization and spectroscopy techniques and thermal analysis methods. Special attention is paid to the characterization of the mechanical consequences of self-healing. The effects of self-healing on the mechanical properties such as stiffness and adhesion of the damaged material are evaluated using the tensile test, double cantilever beam test, plane strip test, bending test, and adhesion test (e.g., blister test). Finally, the future direction of the development of these systems is discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Morphology of immature stages of blow fly, Lucilia sinensis Aubertin (Diptera: Calliphoridae), a potential species of forensic importance.

PubMed

Sanit, Sangob; Sukontason, Kom; Kurahashi, Hiromu; Tomberlin, Jeffery K; Wannasan, Anchalee; Kraisittipanit, Rungroj; Sukontason, Kabkaew L

2017-12-01

Lucilia sinensis Aubertin (Diptera: Calliphoridae) is a blow fly species of potential forensic importance since adults are attracted to, and colonize, decomposing vertebrate remains. Blow fly larvae associated with human corpses can be useful evidence in forensic investigations; however, their use is dependent in most cases on proper species identification and availability of developmental data. For identification, morphological information on each life stage is traditionally used. We used scanning electron microscopy (SEM) to examine the ultrastructure of eggs, all instars, and puparia, of L. sinensis. The important characteristics used to differentiate L. sinensis from other species are provided. Distinctive features of the eggs are the slight widening median area extending almost the entire length. The last abdominal segment of the first instar bears elongated outer ventral tubercles along the rim of the last abdominal segment. These tubercles, as well as the well developed median and outer dorsal tubercles, are more prominent in the second and third instars. The surface integument of the tubercles is equipped with circular rows of microtrichia. Pairs of inner dorsal tubercle are absent. Each anterior spiracle is comprised of 9-12 papillae arrange in a single row in the second and third instars. As for the third instar, the dorsal spines between the first and second thoracic segments are delicate, narrow, small, and close together (as row or set). The peristigmatic tufts adjacent to the posterior spiracle of the third instar are moderately branches of short, fine hairs, but minute in puparia. In conclusion, the prominent outer ventral tubercle in all instars and puparia is a new diagnostic feature of L. sinensis and helpful in differentiating it from other Lucilia species that are forensically important. The description of immature L. sinensis in this study will be useful for forensic entomologists in countries where this species exists. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of drying time and temperature on bond strength of contemporary adhesives to dentine.

PubMed

Garcia, Fernanda C P; Almeida, Júlio C F; Osorio, Raquel; Carvalho, Ricardo M; Toledano, Manuel

2009-04-01

To evaluate the bond strength (microTBS) of self-etching adhesives in different solvent evaporation conditions. Flat dentine surfaces from extracted human third molars were bonded with: (1) 2 two-steps self-etching adhesives (Clearfil SE Bond-CSEB); (Protect Bond-PB) and (2) 2 one-step self-etch systems (Adper Prompt L Pop-ADPLP); (Xeno III-XIII). Bonded dentine surfaces were air-dried for 5s, 20s, 30s or 40s at either 21 degrees C or 38 degrees C. Composite build-ups were constructed incrementally. After storage in water for 24h at 37 degrees C, the specimens were prepared for microtensile bond strength testing. Data were analyzed by two-way ANOVA and Student-Newman-Keuls at alpha=0.05. CSEB and PB performed better at warm temperature with only 20s of air-blowing. The bond strength increased when XIII was performed at warm temperature at 40s air-blowing. Extended air-blowing not affect the performance of ADPLP, except at 30s air-blowing time at warm temperature. The use of a warm air-dry stream seems to be a clinical tool to improve the bond strength to self-etching adhesives.

Aripiprazole.

PubMed

Prommer, Eric

2017-03-01

Delirium is a palliative care emergency where patients experience changes in perception, awareness, and behavior. Common features include changes in the sleep-wake cycle, emotional lability, delusional thinking, and language and thought disorders. Delirium results from neurotransmitter imbalances involving several neurotransmitters such as dopamine, glutamate, norepinephrine, acetylcholine, gamma-aminobutyric acid, and serotonin. Untreated delirium causes significant morbidity and mortality. Nonpharmacologic and pharmacologic approaches treat delirium. Current pharmacologic management of delirium involves using agents such as haloperidol or second-generation antipsychotics. Third-generation atypical antipsychotic drugs have emerged as a potential choice for delirium management. Aripiprazole is a third-generation antipsychotic with a dopamine receptor-binding profile distinct from other second-generation antipsychotics. Aripiprazole acts as partial agonist at dopamine D 2 and 5-hydroxytryptamine (5-HT) 1A receptors, stabilizing the dopamine receptor leading to improvement in symptoms. The article reviews the pharmacology, pharmacodynamics, metabolism, and evidence of clinical efficacy for this new antipsychotic agent. This article explores possible roles in palliative care.

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Michael K.; Brown, Jason R.; Thornberg, Steven Michael

HFE-7100 and FC-72 fluorinert are two fluids used during weapon component manufacturing. HFE-7100 is a solvent used in the cleaning of parts, and FC-72 is the blowing agent of a polymeric removable foam. The presence of either FC-72 or HFE-7100 gas in weapon components can provide valuable information as to the stability of the materials. Therefore, gas standards are needed so HFE-7100 and FC-72 gas concentrations can be accurately measured. There is no current established procedure for generating gas standards of either HFE-7100 or FC-72. This report outlines the development of a method to generate gas standards ranging in concentrationmore » from 0.1 ppm to 10% by volume. These standards were then run on a Jeol GC-Mate II mass spectrometer and analyzed to produce calibration curves. We present a manifold design that accurately generates gas standards of HFE-7100 and FC-72 and a procedure that allows the amount of each to be determined.« less

A Computational Study for the Utilization of Jet Pulsations in Gas Turbine Film Cooling and Flow Control

NASA Technical Reports Server (NTRS)

Kartuzova, Olga V.

2012-01-01

This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.

X-29 vortex flow control tests

NASA Technical Reports Server (NTRS)

Hancock, Regis; Fullerton, Gordon

1992-01-01

A joint Air Force/NASA X-29 aircraft program to improve yaw control at high angle of attack using vortex flow control (VFC) is described. Directional VFC blowing proved to a be a powerful yaw moment generator and was very effective in overriding natural asymmetries, but was essentially ineffective in suppressing wing rock. Symmetric aft blowing also had little effect on suppressing wing rock.

Method of fabricating nested shells and resulting product

DOEpatents

Henderson, Timothy M.; Kool, Lawrence B.

1982-01-01

A multiple shell structure and a method of manufacturing such structure wherein a hollow glass microsphere is surface treated in an organosilane solution so as to render the shell outer surface hydrophobic. The surface treated glass shell is then suspended in the oil phase of an oil-aqueous phase dispersion. The oil phase includes an organic film-forming monomer, a polymerization initiator and a blowing agent. A polymeric film forms at each phase boundary of the dispersion and is then expanded in a blowing operation so as to form an outer homogeneously integral monocellular substantially spherical thermoplastic shell encapsulating an inner glass shell of lesser diameter.

Blow spinning of food-grade-gelatin nanofibers (abstract)

USDA-ARS?s Scientific Manuscript database

Nanofibers have been examined for many diverse applications, including catalysis, filtration, controlled release of drugs and active agents, sensor, and tissue engineering and as texturized food ingredients. The primary advantage of nanofibers over larger diameter fibers is the larger surface area t...

Developing testing methods for characterizing emissions and sources of exposures from polyurehane products

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanate compounds, amine catalysts, flame retardants, and blowing agents, as well as aldehydes and other volatile or semivolatile organic compounds that may be...

A life-cycle comparison of several auxiliary blowing agents used for the manufacture of rigid polyurethane foam.

PubMed

Katz, Seton; Lindner, Angela S

2003-04-01

In a commitment to zero ozone depletion, the United Nations and the U.S. Environmental Protection Agency (EPA) have called for the phase-out of the manufacture and import of hydrochlorofluorocarbons (HCFCs), used as auxiliary blowing agents (ABAs) in the manufacture of polyurethane foams. As a result, more environmentally benign alternative ABAs are being sought by the foam-blowing industry. This study examined the life cycle of HCFC-22, hydrofluorocarbon-134a (HFC-134a), and cyclopentane, which are currently used or considered as potential alternative ABAs in the manufacture of rigid polyurethane foams that serve as insulation in a model North American refrigerator. The raw material extraction/refining, manufacturing, use, and disposal stages of the life cycle of each ABA were considered, and their resulting relative impacts on ozone depletion and global warming were compared. The manufacturing, use, and disposal stages were determined to affect ozone depletion and global warming to the largest extent, emphasizing the need for a greater focus on pollution prevention opportunities in these stages. The HFC-134a life cycle yields no impact on ozone depletion and a significantly decreased global warming impact compared with its predecessor, HCFC-22, and a tradeoff of slightly higher global warming impact and fewer added safety concerns compared with its more flammable counterpart, cyclopentane.

Further studies of turbulence structure resulting from interactions between embedded vortices and wall jets at high blowing ratios

NASA Astrophysics Data System (ADS)

Doner, William D.

1989-12-01

Interactions of wall jets and vortices embedded in turbulent layers commonly occur near gas turbine blades and endwalls where film cooling is employed. These interactions frequently result in undesirable heat transfer effects at blade and endwall surfaces. In this thesis, a crossed hot-wire probe is used to measure the turbulence structure resulting from this type of interaction. The vortex is generated using a half delta-wing vortex generator mounted 12 deg with respect to a 10 m/s mean velocity flow over a flat plate. A single injection hole, 0.95 cm in diameter, inclined 30 deg to the horizontal, is positioned 59.3 cm downstream of the vortex generator. The vortex generator is positioned so that vortex upwash and downwash could be located over the injection hole. Streamwise development of the turbulent boundary layer was investigated for the following cases: (1) boundary layer with jet only (m = 1.5), and (2) boundary layer with vortex only. Measurement of interaction between the boundary layer, vortex upwash, and the wall jet was made at one station with various blowing ratios. At low blowing ratios (m = 0.5 and 1.5) the vortex dominates the flow. Significant alterations to the turbulent structure are seen in the Reynolds stress components, vorticity distributions and mean velocities. At higher blowing ratios (m = 2.5 and 3.5) the jet dominates the flow, the vortex is blown away from the wall, and its turbulence effects are dispersed over a larger area.

A Mathematical Model for Reactions During Top-Blowing in the AOD Process: Validation and Results

NASA Astrophysics Data System (ADS)

Visuri, Ville-Valtteri; Järvinen, Mika; Kärnä, Aki; Sulasalmi, Petri; Heikkinen, Eetu-Pekka; Kupari, Pentti; Fabritius, Timo

2017-06-01

In earlier work, a fundamental mathematical model was proposed for side-blowing operation in the argon oxygen decarburization (AOD) process. In the preceding part "Derivation of the Model," a new mathematical model was proposed for reactions during top-blowing in the AOD process. In this model it was assumed that reactions occur simultaneously at the surface of the cavity caused by the gas jet and at the surface of the metal droplets ejected from the metal bath. This paper presents validation and preliminary results with twelve industrial heats. In the studied heats, the last combined-blowing stage was altered so that oxygen was introduced from the top lance only. Four heats were conducted using an oxygen-nitrogen mixture (1:1), while eight heats were conducted with pure oxygen. Simultaneously, nitrogen or argon gas was blown via tuyères in order to provide mixing that is comparable to regular practice. The measured carbon content varied from 0.4 to 0.5 wt pct before the studied stage to 0.1 to 0.2 wt pct after the studied stage. The results suggest that the model is capable of predicting changes in metal bath composition and temperature with a reasonably high degree of accuracy. The calculations indicate that the top slag may supply oxygen for decarburization during top-blowing. Furthermore, it is postulated that the metal droplets generated by the shear stress of top-blowing create a large mass exchange area, which plays an important role in enabling the high decarburization rates observed during top-blowing in the AOD process. The overall rate of decarburization attributable to top-blowing in the last combined-blowing stage was found to be limited by the mass transfer of dissolved carbon.

Development and Qualification of Alternate Blowing Agents for Space Shuttle External Tank Thermal Protection System

NASA Technical Reports Server (NTRS)

Williams, Charles W.; Cavalaris, James G.

1994-01-01

The Aerospace industry has a long history of using low density polyurethane and polyurethane-modified isocyanurate foam systems as lightweight, low cost, easily processed cryogenic Thermal Protection Systems (TPS) for ascent vehicles. The Thermal Protection System of the Space Shuttle External Tank (ET) is required so that quality liquid cryogenic propellant can be supplied to the Orbiter main engines and to protect the metal structure of the tanks from becoming too hot from aerodynamic heating, hence preventing premature break-up of the tank. These foams are all blown with CFC-1 I blowing agent which has been identified by the Environmental Protection Agency (EPA) as an ozone depleting substance. CFCs will not be manufactured after 1995, Consequently, alternate blowing agent substances must be identified and implemented to assure continued ET manufacture and delivery. This paper describes the various testing performed to select and qualify HCFC-1 41 b as a near term drop-in replacement for CFC-11. Although originally intended to be a one for one substitution in the formulation, several technical issues were identified regarding material performance and processability which required both formulation changes and special processing considerations to overcome. In order to evaluate these material changes, each material was subjected to various tests to qualify them to meet the various loads imposed on them during long term storage, pre-launch operations, launch, separation and re-entry. Each material was tested for structural, thermal, aeroshear, and stress/strain loads for the various flight environments each encounters. Details of the development and qualification program and the resolution of specific problems are discussed in this paper.

Development of mass production type rigid polyurethane foam for LNG carrier using ozone depletion free blowing agent

NASA Astrophysics Data System (ADS)

Lee, Yeongbeom; Baek, Kye Hyun; Choe, Kunhyung; Han, Chonghun

2016-12-01

Nowadays the price of natural gas has become higher and the efficiency of propulsion system of liquefied natural gas (LNG) carriers has improved. Due to these trends, required boil-off rate (BOR) for LNG carrier has been lowered from 0.15%/day to 0.12%/day for conventional LNG carriers with sizes between 125,000 m3 and 170,000 m3. This requirement of BOR can be satisfied by using a rigid polyurethane foam (PUF) blown by 1,1-dichloro-1-fluoroethane (HCFC-141b) as an insulator. However, ozone depletion potential (ODP) of HCFC-141b requires alternative blowing agents with zero ODP such as hydroflurocarbons (HFCs) because of tougher environmental regulations. This paper introduces use of HFCs and additives to enhance properties of rigid PUFs under a mass production environment. Among the additives, perfluoroalkane (PFA) reduces thermal conductivity down to 12% and increases compressive strength up to 15% of a rigid PUF prepared in a laboratory scale. Based on this result, a mass production type rigid PUF is manufactured and is evaluated for BOR, mechanical strengths over operation temperature range, and thermal shock stability for LNG carriers. The BOR of the manufactured rigid PUF is below 0.12%/day, which satisfies the recent BOR specification for LNG carriers. The other required properties are also met the specifications for a conventional LNG carrier. Consequently, it is expected that the results in this paper will bring low BOR (<0.12%/day) LNG carries with rigid PUFs using ODP free blowing agents and contribute environmental protection through saving energy and preserving the ozone layer in the stratosphere.

The problem of modeling the process of air blowing through finely perforated wall for skin friction reduction

NASA Astrophysics Data System (ADS)

Kornilov, V. I.; Boiko, A. V.

2017-10-01

Problems of experimental modeling of the process of air blowing into turbulent boundary layer of incompressible fluid through finely perforated wall are discussed. Particular attention is paid to the analysis of both the main factors responsible for the effectiveness of blowing and the possibility of studying the factors in artificially generated turbulent boundary layer. It was shown that uniformity of the injected gas is one of the main requirements to enhance the effectiveness of this method of flow control. An example of the successful application of this technology exhibiting a significant reduction of the turbulent skin friction is provided.

Chemicals used in the rubber industry. An overview.

PubMed

Fishbein, L

1983-01-01

Hundreds of chemicals illustrative of many structural and use categories are employed in the rubber industry. The present overview has centered on the structural features of a number of compounds representative of several select use categories, eg, vulcanizing agents, accelerators, antioxidants, antiozonants, and blowing agents, with focus on the nature of their impurities, their chemical degradation, and by-products, as well as on those chemicals that can be converted to N-nitrosamines.

Mutagen and Oncogen Study on JP-4

DTIC Science & Technology

1978-09-01

random bred mice were killed by cranial blow , decapitated and bled. The liver was immediately dissected from the animal using aseptic technique and placed...chemical. Positive Controls--N-methylnitrosoguanidine (MNNG) at a concentration of 10 pg/ml was used as the positive control agent in nonactivation tests...The positive control agent in activation tests was 3,4-benzo(u)pyrene (BiP) at a concentration of 10 pg/ml. EXPERIMENTAL DESIGN Cell Preparation

Numerical Modeling of Nanocellular Foams Using Classical Nucleation Theory and Influence Volume Approach

NASA Astrophysics Data System (ADS)

Khan, Irfan; Costeux, Stephane; Bunker, Shana; Moore, Jonathan; Kar, Kishore

2012-11-01

Nanocellular porous materials present unusual optical, dielectric, thermal and mechanical properties and are thus envisioned to find use in a variety of applications. Thermoplastic polymeric foams show considerable promise in achieving these properties. However, there are still considerable challenges in achieving nanocellular foams with densities as low as conventional foams. Lack of in-depth understanding of the effect of process parameters and physical properties on the foaming process is a major obstacle. A numerical model has been developed to simulate the simultaneous nucleation and bubble growth during depressurization of thermoplastic polymers saturated with supercritical blowing agents. The model is based on the popular ``Influence Volume Approach,'' which assumes a growing boundary layer with depleted blowing agent surrounds each bubble. Classical nucleation theory is used to predict the rate of nucleation of bubbles. By solving the mass balance, momentum balance and species conservation equations for each bubble, the model is capable of predicting average bubble size, bubble size distribution and bulk porosity. The model is modified to include mechanisms for Joule-Thompson cooling during depressurization and secondary foaming. Simulation results for polymer with and without nucleating agents will be discussed and compared with experimental data.

Development of test systems for characterizing emissions from spray polyurethane foam insulation (SPFI)

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanates, amines, flame retardants (FRs), blowing agents, aldehydes and other organic compounds that may be emitted from SPFI is not well understood. EPA is de...

Manufacturing a Porous Structure According to the Process Parameters of Functional 3D Porous Polymer Printing Technology Based on a Chemical Blowing Agent

NASA Astrophysics Data System (ADS)

Yoo, C. J.; Shin, B. S.; Kang, B. S.; Yun, D. H.; You, D. B.; Hong, S. M.

2017-09-01

In this paper, we propose a new porous polymer printing technology based on CBA(chemical blowing agent), and describe the optimization process according to the process parameters. By mixing polypropylene (PP) and CBA, a hybrid CBA filament was manufactured; the diameter of the filament ranged between 1.60 mm and 1.75 mm. A porous polymer structure was manufactured based on the traditional fused deposition modelling (FDM) method. The process parameters of the three-dimensional (3D) porous polymer printing (PPP) process included nozzle temperature, printing speed, and CBA density. Porosity increase with an increase in nozzle temperature and CBA density. On the contrary, porosity increase with a decrease in the printing speed. For porous structures, it has excellent mechanical properties. We manufactured a simple shape in 3D using 3D PPP technology. In the future, we will study the excellent mechanical properties of 3D PPP technology and apply them to various safety fields.

Gas Release Behavior of Cu-TiH2 Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

NASA Astrophysics Data System (ADS)

Cheng, Ying; Li, Yanxiang; Chen, Xiang; Liu, Zhiyong; Zhou, Xu; Wang, Ningzhen

2018-06-01

Compared to traditional pore structure with high porosity (≥ 80 pct) and large pore size (≥ 3 mm), aluminum foams with low porosity (60 to 70 pct) and small pore size (≤ 2 mm) possess higher compressive property and formability. In order to achieve the goal of reducing pore size, Cu-TiH2 composite powder prepared by ball milling preoxidized TiH2 with Cu powder was used as a blowing agent. Its gas release behavior was characterized by thermogravimetric analysis and differential scanning calorimetry. The results show that the ball milling treatment can advance the gas release process and slow the gas release rate at the same time. All these changes are favorable to the reduction of porosity and pore size. Such Cu-TiH2 composite powder provides an alternative way to fabricate aluminum foams with low porosity and small pore size.

Computational analysis of forebody tangential slot blowing on the high alpha research vehicle

NASA Technical Reports Server (NTRS)

Gee, Ken

1995-01-01

A numerical analysis of forebody tangential slot blowing as a means of generating side force and yawing moment is conducted using an aircraft geometry. The Reynolds-averaged, thin-layer, Navier-Stokes equations are solved using a partially flux-split, approximately-factored algorithm. An algebraic turbulence model is used to determine the turbulent eddy viscosity values. Solutions are obtained using both patched and overset grid systems. In the patched grid model, and actuator plane is used to introduce jet variables into the flow field. The overset grid model is used to model the physical slot geometry and facilitate modeling of the full aircraft configuration. A slot optimization study indicates that a short slot located close to the nose of the aircraft provided the most side force and yawing moment per unit blowing coefficient. Comparison of computed surface pressure with that obtained in full-scale wind tunnel tests produce good agreement, indicating the numerical method and grid system used in the study are valid. Full aircraft computations resolve the changes in vortex burst point due to blowing. A time-accurate full-aircraft solution shows the effect of blowing on the changes in the frequency of the aerodynamic loads over the vertical tails. A study of the effects of freestream Mach number and various jet parameters indicates blowing remains effective through the transonic Mach range. An investigation of the force onset time lag associated with forebody blowing shows the lag to be minimal. The knowledge obtained in this study may be applied to the design of a forebody tangential slot blowing system for use on flight aircraft.

Self-healing fiber-reinforced composite

NASA Astrophysics Data System (ADS)

Lee, Minwook; Yoon, Sam; Yarin, Alexander

In the present work two parts of the healing agent (commercially available epoxy resin and hardener) are encapsulated in separate polymeric nanofibers. The fibers are generated by a single-step dual coaxial solution blowing. The core-shell fibers with the diameters in the 200-2600 nm range are encased in the PDMS (polydimethyl siloxane) matrix to form a self-healing composite material. Under fatigue conditions, the core-shell fibers inside the composite material are ruptured and the healing agents released into the surrounding matrix. Various fatigue conditions including repeated bending and stretching are used to damage the composites and the degree of self-healing is quantified after that. Also, an incision resembling a crack is pre-notched and crack propagation is studied. It is found that the presence of the self-healing agents in the fibers significantly retards crack propagation due to curing by the epoxy at the ruptured site. The stiffness of the composites is also measured for the samples containing self-healing fibers inside them before and after the fatigue tests. A novel theory of crack propagation is proposed, which explains the observed jump-like growth of sub-critical cracks. This work was supported by the International Collaboration Program funded by the Agency for Defense Development.

German ’AT’ Mine Units

DTIC Science & Technology

1945-09-28

a fixed - osition by an arm mount- ed on the tail door, and the magnetonhone is released by the blow- ing of a fuse when -the mine becomes armed, it... sensitivity of the unit. The output is condenser-couoled to the second stage. The output of the sec- ond stage is trnnsformer-cou-oled to the third...no orovision for setting sensitivity similar to that u~ed in AT 2. As well, that third rtage is omitted, and the output of the second stage is

MRI brain in monohalomethane toxic encephalopathy: A case report.

PubMed

Deshmukh, Yogeshwari S; Atre, Ashish; Shah, Darshan; Kothari, Sudhir

2013-07-01

Monohalomethanes are alkylating agents that have been used as methylating agents, laboratory reagents, refrigerants, aerosol propellants, pesticides, fumigants, fire-extinguishing agents, anesthetics, degreasers, blowing agents for plastic foams, and chemical intermediates. Compounds in this group are methyl chloride, methyl bromide, methyl iodide (MI), and methyl fluoride. MI is a colorless volatile liquid used as a methylating agent to manufacture a few pharmaceuticals and is also used as a fumigative insecticide. It is a rare intoxicant. Neurotoxicity is known with both acute and chronic exposure to MI. We present the characteristic magnetic resonance imaging (MRI) brain findings in a patient who developed neuropsychiatric symptoms weeks after occupational exposure to excessive doses of MI.

Occupational asthma after exposure to azodicarbonamide: report of four cases.

PubMed Central

Normand, J C; Grange, F; Hernandez, C; Ganay, A; Davezies, P; Bergeret, A; Prost, G

1989-01-01

Azodicarbonamide (Chemical Abstract Service Registry No 123.77.3) is an organic low molecular weight agent used for blowing and foaming plastics. Finely ground azodicarbonamide can be a pulmonary and sometimes a cutaneous acute sensitiser. Four cases of work related asthma are reported. PMID:2920144

Combustion Instabilities In Solid Propellant Rocket Motors

DTIC Science & Technology

2004-01-01

instability in a self-excited system, sketched in Figure 1.5(a). In contrast, the initial transient in a linear system forced by an invariant external agent ...because the driving agent supplies only ¯nite power. (a) (b) Figure 1.5. Transient behavior of (a) Self Excited Linearly Unstable Motions; (b) Forced...the vibration of a Helmholtz resonator obtained, for example, by blowing over the open end of a bottle. The cause in a combustion chamber may be the

Blowing Carbon Nanotubes to Carbon Nanobulbs

NASA Astrophysics Data System (ADS)

Su, D. S.; Zhu, Z. P.; Lu, Y.; Schlögl, R.; Weinberg, G.; Liu, Z. Y.

2004-09-01

We report the blowing of multi-walled carbon nanotubes into carbon nanobulbs. This is realized in a unique tube growth environment generated by explosive decomposition of picric acid mixed with nickel formate. The carbon spherical bulbs are characterized by large dimensions (up to 900 nm), thin walls (around 10 nm), and fully hollow cores. The walls are in graphitic structure of sp2 hybridized carbons. Bulb-tube assemblies are found as intermediate derivatives of blowing. A joint action of the filled high-pressure gases and the structural defects in the carbon nanotubes is responsible to the formation of the carbon nanobulbs. Our finding may indicate the possibility to engineer the carbon nanotubes to the designed nanostructures.

Simulation of CO2 Solubility in Polystyrene-b-Polybutadieneb-Polystyrene (SEBS) by artificial intelligence network (ANN) method

NASA Astrophysics Data System (ADS)

Sharudin, R. W.; AbdulBari Ali, S.; Zulkarnain, M.; Shukri, M. A.

2018-05-01

This study reports on the integration of Artificial Neural Network (ANNs) with experimental data in predicting the solubility of carbon dioxide (CO2) blowing agent in SEBS by generating highest possible value for Regression coefficient (R2). Basically, foaming of thermoplastic elastomer with CO2 is highly affected by the CO2 solubility. The ability of ANN in predicting interpolated data of CO2 solubility was investigated by comparing training results via different method of network training. Regards to the final prediction result for CO2 solubility by ANN, the prediction trend (output generate) was corroborated with the experimental results. The obtained result of different method of training showed the trend of output generated by Gradient Descent with Momentum & Adaptive LR (traingdx) required longer training time and required more accurate input to produce better output with final Regression Value of 0.88. However, it goes vice versa with Levenberg-Marquardt (trainlm) technique as it produced better output in quick detention time with final Regression Value of 0.91.

Larval Distribution and Behavior of Chrysomya rufifacies (Macquart) (Diptera: Calliphoridae) Relative to Other Species on Florida Black Bear (Carnivora: Ursidae) Decomposing Carcasses.

PubMed

Swiger, S L; Hogsette, J A; Butler, J F

2014-02-01

Larval interactions of dipteran species, blow flies in particular, were observed and documented daily over time and location on five black bear carcasses in Gainesville, FL, USA, from June 2002 - September 2004. Cochliomyia macellaria (Fabricius) or Chrysomya megacephala (Fabricius) larvae were collected first, after which Chrysomya rufifacies (Macquart) oviposited on the carcasses in multiple locations (i.e., neck, anus, and exposed flesh) not inhabited already by the other blow fly larvae. Within the first week of decomposition, C. rufifacies larvae grew to ≥12 mm, filling the carcasses with thousands of larvae and replacing the other calliphorid larvae either through successful food source competition or by predation. As a result, C. macellaria and C. megacephala were not collected past their third instar feeding stage. The blow fly species, C. megacephala, C. macellaria, Lucilia caeruleiviridis (Macquart), Phormia regina (Meigen), Lucilia sericata (Meigen), and C. rufifacies, completed two developmental cycles in the 88.5-kg carcass. This phenomenon might serve to complicate or prevent the calculation of an accurate postmortem interval.

Mutagen and Oncogen Study on JP-8

DTIC Science & Technology

1978-09-01

as indicated for the nonactivated cells. Preparation of 9,000 x g Supernatant Male random bred mice were killed by cranial blow , decapitated and bled...at a concentration of 10 pg/ml was used as the positive control agent in nonactivation tests. The positive control agent in activation tests was 3,4...plate were covered with 2.5% sodium dodecyl sulfate (SDS) in 1 x (SSC) (0.15M NaCl - 0.015M Na citrate ) and scraped from the dish with a rubber

Mutagen and Oncogen Study on RJ-4

DTIC Science & Technology

1978-09-01

indicated for the nonactivated cells. Preparation of 9,000 x g Supernatant Male random bred mice were killed by cranial blow , decapitated and bled...used as the positive control agent in nonactivation tests. The positive control agent in activation tests was 3,4-benzo(ot)pyrene (BaP) at a...sodium dodecyl sulfate (SDS) in 1 x (SSC) (0.15M NaCl - 0.015M Na citrate ) and scraped from the dish with a rubber policeman. The cells were washed and

Novel thick-foam ferroelectret with engineered voids for energy harvesting applications

NASA Astrophysics Data System (ADS)

Luo, Z.; Shi, J.; Beeby, S. P.

2016-11-01

This work reports a novel thick-foam ferroelectret which is designed and engineered for energy harvesting applications. We fabricated this ferroelectret foam by mixing a chemical blowing agent with a polymer solution, then used heat treatment to activate the agent and create voids in the polymer foam. The dimensions of the foam, the density and size of voids can be well controlled in the fabrication process. Therefore, this ferroelectret can be engineered into optimized structure for energy harvesting applications.

Thrust Removal Scheme for the FAST-MAC Circulation Control Model Tested in the National Transonic Facility

NASA Technical Reports Server (NTRS)

Chan, David T.; Milholen, William E., II; Jones, Gregory S.; Goodliff, Scott L.

2014-01-01

A second wind tunnel test of the FAST-MAC circulation control semi-span model was recently completed in the National Transonic Facility at the NASA Langley Research Center. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged flap. The model was configured for transonic testing of the cruise configuration with 0deg flap deflection to determine the potential for drag reduction with the circulation control blowing. Encouraging results from analysis of wing surface pressures suggested that the circulation control blowing was effective in reducing the transonic drag on the configuration, however this could not be quantified until the thrust generated by the blowing slot was correctly removed from the force and moment balance data. This paper will present the thrust removal methodology used for the FAST-MAC circulation control model and describe the experimental measurements and techniques used to develop the methodology. A discussion on the impact to the force and moment data as a result of removing the thrust from the blowing slot will also be presented for the cruise configuration, where at some Mach and Reynolds number conditions, the thrust-removed corrected data showed that a drag reduction was realized as a consequence of the blowing.

Efficacy and safety of the third-generation chloroethylnitrosourea fotemustine for the treatment of chemorefractory T-cell lymphomas

PubMed Central

Corazzelli, Gaetano; Frigeri, Ferdinando; Arcamone, Manuela; Aloj, Luigi; Capobianco, Gaetana; Becchimanzi, Cristina; Morelli, Emanuela; Volzone, Francesco; Marcacci, Gianpaolo; Russo, Filippo; De Filippi, Rosaria; Lastoria, Secondo; Pinto, Antonio

2011-01-01

Patients with recurring T-cell non-Hodgkin lymphoma (T-NHL) are incurable and candidate for investigational agents. Here, we report on five patients with T-NHL refractory to multiple chemotherapy lines, including in all cases alkylators and gemcitabine, who received the third-generation chloroethylnitrosourea fotemustine at a dose of 120 mg/m2 every 21 d, up to eight courses. Median actual dose intensity was 79%; toxicity was manageable and mainly hematological. One complete remission, one partial remission, two protracted disease stabilization, and one transient, minor response were achieved. Time to progression ranged from 48 to 240+ d. This is the first evidence ever reporting the activity of fotemustine in end-stage T-NHL. Formal studies with this agent are warranted in T-cell malignancies. PMID:21752099

Intumescent all-polymer multilayer nanocoating capable of extinguishing flame on fabric

USDA-ARS?s Scientific Manuscript database

Cotton fabric was treated with flame-retardant coatings composed of poly (sodium phosphate), PSP, which acts as the acid source, and poly (allylamine), PAAm, which is used as the blowing agent, prepared via layer-by-layer (LbL) assembly. By applying these thin coating on fabric, after-glow is elimi...

Trends in Navy Waste Reduction and Materials Markets.

DTIC Science & Technology

1981-06-01

227 5,838 GENERAL PACKAGING 4,869 4,839 30 185 4,684 Aerosol 2,202 2,172 30 100 2,102 Motor Oil 546 546 -0- -0- 546 Paint & Varnish 873 873 -0- -0- 873...antioxidants, antistats, blowing agents, colorants, fluorine retardants, organic peroxides, plasticizers and ultraviolet stabilizers can be added to

A finite element analysis of the stress distribution to the mandible from impact forces with various orientations of third molars*

PubMed Central

Liu, Yun-feng; Wang, Russell; Baur, Dale A.; Jiang, Xian-feng

2018-01-01

Objective: To investigate the stress distribution to the mandible, with and without impacted third molars (IM3s) at various orientations, resulting from a 2000-Newton impact force either from the anterior midline or from the body of the mandible. Materials and methods: A 3D mandibular virtual model from a healthy dentate patient was created and the mechanical properties of the mandible were categorized to 9 levels based on the Hounsfield unit measured from computed tomography (CT) images. Von Mises stress distributions to the mandibular angle and condylar areas from static impact forces (Load I-front blow and Load II left blow) were evaluated using finite element analysis (FEA). Six groups with IM3 were included: full horizontal bony, full vertical bony, full 450 mesioangular bony, partial horizontal bony, partial vertical, and partial 450 mesioangular bony impaction, and a baseline group with no third molars. Results: Von Mises stresses in the condyle and angle areas were higher for partially than for fully impacted third molars under both loading conditions, with partial horizontal IM3 showing the highest fracture risk. Stresses were higher on the contralateral than on the ipsilateral side. Under Load II, the angle area had the highest stress for various orientations of IM3s. The condylar region had the highest stress when IM3s were absent. Conclusions: High-impact forces are more likely to cause condylar rather than angular fracture when IM3s are missing. The risk of mandibular fracture is higher for partially than fully impacted third molars, with the angulation of impaction having little effect on facture risk. PMID:29308606

Preparation of polyurethane foams using liquefied oil palm mesocarp fibre (OPMF) and renewable monomer from waste cooking oil

NASA Astrophysics Data System (ADS)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-09-01

The aim of this research is the production of polyurethane (PU) foams with biopolyols from liquefied oil palm mesocarp fibre (OPMF) and renewable monomer. Liquefaction of OPMF was studied using polyhydric alcohol (PA) which is PEG-400 as liquefaction solvents in conventional glass flask. In the second part of this paper was obtained the PU foams which presented good results when compared with commercial foams and include polyols from of fossil fuels. PU foams were prepared by mixing liquefied OPMF biopolyol, renewable monomer from waste cooking, additives and methylene diphenyl diisocyanate (MDI). Water was used as an environmental friendly blowing agent. The factors that influence the cell structure of foams (i.e., catalyst, surfactant, dosage of blowing agent, and mass ratio of biopolyol to renewable monomer were studied. The synthesized PU foams were characterized by FTIR and SEM. The formulation of the PU foams should be improved, but the results show that is possible the use biopolyols and renewable monomer to produce industrial foams with lower cost.

Broadband Noise Reduction of a Low-Speed Fan Noise Using Trailing Edge Blowing

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2005-01-01

An experimental proof-of-concept test was conducted to demonstrate reduction of rotor-stator interaction noise through the use of rotor-trailing edge blowing. The velocity deficit from the viscous wake of the rotor blades was reduced by injecting air into the wake from a continuous trailing edge slot. Hollow blades with interior guide vanes create flow channels through which externally supplied air flows from the blade root to the trailing edge. A previous paper documented the substantial tonal reductions of this Trailing Edge Rotor Blowing (TERB) fan. This report documents the broadband characteristics of TERB. The Active Noise Control Fan (ANCF), located at the NASA Glenn Research Center, was used as the proof-of-concept test bed. Two-component hotwire data behind the rotor, unsteady surface pressures on the stator vane, and farfield directivity acoustic data were acquired at blowing rates of 1.1, 1.5, and 1.8 percent of the total fan mass flow. The results indicate a substantial reduction in the rotor wake turbulent velocity and in the stator vane unsteady surface pressures. Based on the physics of the noise generation, these indirect measurements indicate the prospect of broadband noise reduction. However, since the broadband noise generated by the ANCF is rotor-dominated, any change in the rotor-stator interaction broadband noise levels is barely distinguishable in the farfield measurements.

Morphologies, Processing and Properties of Ceramic Foams and Their Potential as TPS Materials

NASA Technical Reports Server (NTRS)

Stackpoole, Mairead; Simoes, Conan R.; Johnson, Sylvia M.

2002-01-01

The current research is focused on processing ceramic foams with compositions that have potential as a thermal protection material. The use of pre-ceramic polymers with the addition of sacrificial blowing agents or sacrificial fillers offers a viable approach to form either open or closed cell insulation. Our work demonstrates that this is a feasible method to form refractory ceramic foams at relatively low processing temperatures. It is possible to foam complex shapes then pyrolize the system to form a ceramic while retaining the shape of the unfired foam. Initial work focused on identifying suitable pre-ceramic polymers with desired properties such as ceramic yield and chemical make up of the pyrolysis product after firing. We focused on making foams in the Si system (Sic, Si02, Si-0-C), which is in use in current acreage TPS systems. Ceramic foams with different architectures were formed from the pyrolysis of pre-ceramic polymers at 1200 C in different atmospheres. In some systems a sacrificial polyurethane was used as the blowing agent. We have also processed foams using sacrificial fillers to introduce controlled cell sizes. Each sacrificial filler or blowing agent leads to a unique morphology. The effect of different fillers on foam morphologies and the characterization of these foams in terms of mechanical and thermal properties are presented. We have conducted preliminary arc jet testing on selected foams with the materials being exposed to typical re-entry conditions for acreage TPS and these results will be discussed. Foams processed using these approaches have bulk densities ranging from 0.15 to 0.9 g/cm3 and cell sizes ranging from 5 to 500 pm. Compression strengths ranged from 2 to 7 MPa for these systems. Finally, preliminary oxidation studies have been conducted on selected systems and will be discussed.

A multi-agent approach to intelligent monitoring in smart grids

NASA Astrophysics Data System (ADS)

Vallejo, D.; Albusac, J.; Glez-Morcillo, C.; Castro-Schez, J. J.; Jiménez, L.

2014-04-01

In this paper, we propose a scalable multi-agent architecture to give support to smart grids, paying special attention to the intelligent monitoring of distribution substations. The data gathered by multiple sensors are used by software agents that are responsible for monitoring different aspects or events of interest, such as normal voltage values or unbalanced intensity values that can end up blowing fuses and decreasing the quality of service of end consumers. The knowledge bases of these agents have been built by means of a formal model for normality analysis that has been successfully used in other surveillance domains. The architecture facilitates the integration of new agents and can be easily configured and deployed to monitor different environments. The experiments have been conducted over a power distribution network.

Efficacy and safety of the third-generation chloroethylnitrosourea fotemustine for the treatment of chemorefractory T-cell lymphomas.

PubMed

Corazzelli, Gaetano; Frigeri, Ferdinando; Arcamone, Manuela; Aloj, Luigi; Capobianco, Gaetana; Becchimanzi, Cristina; Morelli, Emanuela; Volzone, Francesco; Marcacci, Gianpaolo; Russo, Filippo; De Filippi, Rosaria; Lastoria, Secondo; Pinto, Antonio

2011-12-01

Patients with recurring T-cell non-Hodgkin lymphoma (T-NHL) are incurable and candidate for investigational agents. Here, we report on five patients with T-NHL refractory to multiple chemotherapy lines, including in all cases alkylators and gemcitabine, who received the third-generation chloroethylnitrosourea fotemustine at a dose of 120 mg/m(2) every 21 d, up to eight courses. Median actual dose intensity was 79%; toxicity was manageable and mainly hematological. One complete remission, one partial remission, two protracted disease stabilization, and one transient, minor response were achieved. Time to progression ranged from 48 to 240+ d. This is the first evidence ever reporting the activity of fotemustine in end-stage T-NHL. Formal studies with this agent are warranted in T-cell malignancies. © 2011 John Wiley & Sons A/S.

Studies of shock/shock interaction on smooth and transpiration-cooled hemispherical nosetips in hypersonic flow

NASA Technical Reports Server (NTRS)

Holden, Michael S.; Rodriguez, Kathleen M.

1992-01-01

A program of experimental research and analysis was conducted to examine the heat transfer and pressure distributions in regions of shock/shock interaction over smooth and transpiration-cooled hemispherical noseshapes. The objective of this investigation was to determine whether the large heat transfer generated in regions of shock/shock interaction can be reduced by transpiration cooling. The experimental program was conducted at Mach numbers of 12 to 16 in the Calspan 48-Inch Shock Tunnel. Type 3 and type 4 interaction regions were generated for a range of freestream unit Reynolds numbers to provide shear layer Reynolds numbers from 10 exp 4 to 10 exp 6 to enable laminar and turbulent interaction regions to be studied. Shock/shock interactions were investigated on a smooth hemispherical nosetip and a similar transpiration-cooled nosetip, with the latter configuration being examined for a range of surface blowing rates up to one-third of the freestream mass flux. While the heat transfer measurements on the smooth hemisphere without shock/shock interaction were in good agreement with Fay-Riddell predictions, those on the transpiration-cooled nosetip indicated that its intrinsic roughness caused heating-enhancement factors of over 1.5. In the shock/shock interaction studies on the smooth nosetip, detailed heat transfer and pressure measurements were obtained to map the variation of the distributions with shock-impingement position for a range of type 3 and type 4 interactions. Such sets of measurements were obtained for a range of unit Reynolds numbers and Mach numbers to obtain both laminar and turbulent interactions. The measurements indicated that shear layer transition has a significant influence on the heating rates for the type 4 interaction as well as the anticipated large effects on type 3 interaction heating. In the absence of blowing, the peak heating in the type 3 and type 4 interaction regions, over the transpiration-cooled model, did not appear to be influenced by the model's rough surface characteristics. The studies of the effects of the transpiration cooling on type 3 and type 4 shock/shock interaction regions demonstrated that large surface blowing rates had significant effect on the structure of the flowfield, enlarging the shock layer and moving the region of peak-heating interaction around the body.

49 CFR 173.115 - Class 2, Divisions 2.1, 2.2, and 2.3-Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 3A1800”, the service pressure is 12410 kPa (1800 psig). (j) Refrigerant gas or Dispersant gas. The terms Refrigerant gas and Dispersant gas apply to all nonpoisonous refrigerant gases; dispersant gases... °F), used only as a refrigerant, dispersant, or blowing agent. (k) For Division 2.2 gases, the...

49 CFR 173.115 - Class 2, Divisions 2.1, 2.2, and 2.3-Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 3A1800”, the service pressure is 12410 kPa (1800 psig). (j) Refrigerant gas or Dispersant gas. The terms Refrigerant gas and Dispersant gas apply to all nonpoisonous refrigerant gases; dispersant gases... °F), used only as a refrigerant, dispersant, or blowing agent. (k) For Division 2.2 gases, the...

Method of aeration disinfecting and drying grain in bulk and pretreating seeds and a transverse blow silo grain dryer therefor

DOEpatents

Danchenko, Vitaliy G [Dnipropetrovsk, UA; Noyes, Ronald T [Stillwater, OK; Potapovych, Larysa P [Dnipropetrovsk, UA

2012-02-28

Aeration drying and disinfecting grain crops in bulk and pretreating seeds includes passing through a bulk of grain crops and seeds disinfecting and drying agents including an ozone and air mixture and surrounding air, subdividing the disinfecting and drying agents into a plurality of streams spaced from one another in a vertical direction, and passing the streams at different heights through levels located at corresponding heights of the bulk of grain crops and seeds transversely in a substantially horizontal direction.

RETRAN analysis of multiple steam generator blow down caused by an auxiliary feedwater steam-line break

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feltus, M.A.

1987-01-01

Analysis results for multiple steam generator blow down caused by an auxiliary feedwater steam-line break performed with the RETRAN-02 MOD 003 computer code are presented to demonstrate the capabilities of the RETRAN code to predict system transient response for verifying changes in operational procedures and supporting plant equipment modifications. A typical four-loop Westinghouse pressurized water reactor was modeled using best-estimate versus worst case licensing assumptions. This paper presents analyses performed to evaluate the necessity of implementing an auxiliary feedwater steam-line isolation modification. RETRAN transient analysis can be used to determine core cooling capability response, departure from nucleate boiling ratio (DNBR)more » status, and reactor trip signal actuation times.« less

Grid generation by elliptic partial differential equations for a tri-element Augmentor-Wing airfoil

NASA Technical Reports Server (NTRS)

Sorenson, R. L.

1982-01-01

Two efforts to numerically simulate the flow about the Augmentor-Wing airfoil in the cruise configuration using the GRAPE elliptic partial differential equation grid generator algorithm are discussed. The Augmentor-Wing consists of a main airfoil with a slotted trailing edge for blowing and two smaller airfoils shrouding the blowing jet. The airfoil and the algorithm are described, and the application of GRAPE to an unsteady viscous flow simulation and a transonic full-potential approach is considered. The procedure involves dividing a complicated flow region into an arbitrary number of zones and ensuring continuity of grid lines, their slopes, and their point distributions across the zonal boundaries. The method for distributing the body-surface grid points is discussed.

Checklist and distribution maps of the blow flies of Venezuela (Diptera, Calliphoridae, Mesembrinellidae)

PubMed Central

Velásquez, Yelitza; Martínez-Sánchez, Ana Isabel; Thomas, Arianna; Rojo, Santos

2017-01-01

Abstract A checklist of the 39 species of blow flies (Calliphoridae and Mesembrinellidae) so far known to occur in Venezuela is provided, based on a thorough literature review and the examination of ca. 500 specimens deposited in the main entomological collections of the country. Data from the literature and museum collections were used to generate distribution maps for 37 species. Three species are recorded from Venezuela for the first time: Chrysomya putoria (Wiedemann, 1830), Mesembrinella spicata Aldrich, 1925 and Mesembrinella umbrosa Aldrich, 1922. PMID:28228670

Sodium hydrogen carbonate as an alternative blowing agent in the preparation of palm-based polyurethane foam

NASA Astrophysics Data System (ADS)

Shakir, Amira Shakim Abdul; Badri, Khairiah Haji; Hua, Chia Chin

2016-11-01

An environmental-friendly blowing agent has been used to fabricate flexible polyurethane (PU) foam. Polyurethane foam was prepared from palm kernel oil-based monoester polyol (PKO-p) via prepolymerization method. Acetone has been used as solvent in this study. The developed polyurethane foam was characterized using tensile, differential scanning calorimetry analysis (DSC), thermogravimetric analysis (TGA), optical microscope and drop shape analyzer. The mechanical properties of the PU-reference (PU-R) and PU-NaHCO3 foam was analyzed by tensile using ASTM D 3574-01. From the results, the elongation of PU- NaHCO3 shows reduction to 26.3 % compared to PU-R. The DSC showed two glass transition temperatures in all samples that belonged to the PU-R and PU-NaHCO3. TGA revealed that the incorporation of sodium hydrogen carbonate into the PU system did not show significant difference as compared to the control PU. The morphology of both PU was investigated using optical microscope. Contact angle has been measured to determine the hydrophobicity of the PU. The PU- NaHCO3 exhibited an increase in contact angle (93.1°).

Generalized additive models and Lucilia sericata growth: assessing confidence intervals and error rates in forensic entomology.

PubMed

Tarone, Aaron M; Foran, David R

2008-07-01

Forensic entomologists use blow fly development to estimate a postmortem interval. Although accurate, fly age estimates can be imprecise for older developmental stages and no standard means of assigning confidence intervals exists. Presented here is a method for modeling growth of the forensically important blow fly Lucilia sericata, using generalized additive models (GAMs). Eighteen GAMs were created to predict the extent of juvenile fly development, encompassing developmental stage, length, weight, strain, and temperature data, collected from 2559 individuals. All measures were informative, explaining up to 92.6% of the deviance in the data, though strain and temperature exerted negligible influences. Predictions made with an independent data set allowed for a subsequent examination of error. Estimates using length and developmental stage were within 5% of true development percent during the feeding portion of the larval life cycle, while predictions for postfeeding third instars were less precise, but within expected error.

Test and Evaluation Management Guide, Third Edition.

DTIC Science & Technology

1998-03-01

chemical tests — chemical mixing and biotoxicity . Chemical-mixing tests are con- ducted to obtain information on the binary chemical reaction... Biotoxicity tests are per- formed to assess the potency of the agent generated. Chemical weapons testing, of necessity, relies heavily on the use of non

Southeast Asia: The Third Front in the Long War

DTIC Science & Technology

2009-05-04

of 2002 (a significant blow to the tourism industry ). Another Friend of Our Enemy: The Abu Sayyaf Group The Filipino Muslim population...1998, Jemaah Islamiyah entered into phase two and began limited attacks against government entities. Most notable to date has been the Bali bombings...island of Bali . 59 Most were foreigners, mainly Australian tourists. It was preceded by a blast at the U.S. consulate in nearby Denspasar. The

Optimisation of Ferrochrome Addition Using Multi-Objective Evolutionary and Genetic Algorithms for Stainless Steel Making via AOD Converter

NASA Astrophysics Data System (ADS)

Behera, Kishore Kumar; Pal, Snehanshu

2018-03-01

This paper describes a new approach towards optimum utilisation of ferrochrome added during stainless steel making in AOD converter. The objective of optimisation is to enhance end blow chromium content of steel and reduce the ferrochrome addition during refining. By developing a thermodynamic based mathematical model, a study has been conducted to compute the optimum trade-off between ferrochrome addition and end blow chromium content of stainless steel using a predator prey genetic algorithm through training of 100 dataset considering different input and output variables such as oxygen, argon, nitrogen blowing rate, duration of blowing, initial bath temperature, chromium and carbon content, weight of ferrochrome added during refining. Optimisation is performed within constrained imposed on the input parameters whose values fall within certain ranges. The analysis of pareto fronts is observed to generate a set of feasible optimal solution between the two conflicting objectives that provides an effective guideline for better ferrochrome utilisation. It is found out that after a certain critical range, further addition of ferrochrome does not affect the chromium percentage of steel. Single variable response analysis is performed to study the variation and interaction of all individual input parameters on output variables.

Manipulating Morality: Third-Party Intentions Alter Moral Judgments by Changing Causal Reasoning.

PubMed

Phillips, Jonathan; Shaw, Alex

2015-08-01

The present studies investigate how the intentions of third parties influence judgments of moral responsibility for other agents who commit immoral acts. Using cases in which an agent acts under some situational constraint brought about by a third party, we ask whether the agent is blamed less for the immoral act when the third party intended for that act to occur. Study 1 demonstrates that third-party intentions do influence judgments of blame. Study 2 finds that third-party intentions only influence moral judgments when the agent's actions precisely match the third party's intention. Study 3 shows that this effect arises from changes in participants' causal perception that the third party was controlling the agent. Studies 4 and 5, respectively, show that the effect cannot be explained by changes in the distribution of blame or perceived differences in situational constraint faced by the agent. © 2014 Cognitive Science Society, Inc.

Efficacy and safety of emtricitabine/tenofovir alafenamide (FTC/TAF) vs. emtricitabine/tenofovir disoproxil fumarate (FTC/TDF) as a backbone for treatment of HIV-1 infection in virologically suppressed adults: subgroup analysis by third agent of a randomized, double-blind, active-controlled phase 3 trial^.

PubMed

Post, Frank A; Yazdanpanah, Yazdan; Schembri, Gabriel; Lazzarin, Adriano; Reynes, Jacques; Maggiolo, Franco; Yan, Mingjin; Abram, Michael E; Tran-Muchowski, Cecilia; Cheng, Andrew; Rhee, Martin S

2017-05-01

FTC/TAF was shown to be noninferior to FTC/TDF with advantages in markers of renal and bone safety. To evaluate the efficacy and safety of switching to FTC/TAF from FTC/TDF by third agent (boosted protease inhibitor [PI] vs. unboosted third agent). We conducted a 48-week subgroup analysis based on third agent from a randomized, double blind study in virologically suppressed adults on a FTC/TDF-containing regimen who switched to FTC/TAF vs. continued FTC/TDF while remaining on the same third agent. We randomized (1:1) 663 participants to either switch to FTC/TAF (N = 333) or continue FTC/TDF (N = 330), each with baseline third agent stratifying by class of third agent in the prior treatment regimen (boosted PI 46%, unboosted third agent 54%). At week 48, significant differences in renal biomarkers and bone mineral density were observed favoring FTC/TAF over FTC/TDF (p < 0.05 for all), with similar improvements in the FTC/TAF arm in those who received boosted PI vs. unboosted third agents. At week 48, virologic success rates were similar between treatment groups for those who received a boosted PI (FTC/TAF 92%, FTC/TDF 93%) and for those who received an unboosted third agent (97% vs. 93%). In virologically suppressed patients switching to FTC/TAF from FTC/TDF, high rates of virologic suppression were maintained, while renal and bone safety parameters improved, regardless of whether participants were receiving a boosted PI or an unboosted third agent. FTC/TAF offers safety advantages over FTC/TDF and can be an important option as an NRTI backbone given with a variety of third agents.

Processing Characteristics and Properties of the Cellular Products Made by Using Special Foaming Agents

NASA Astrophysics Data System (ADS)

Garbacz, Tomasz; Dulebova, Ludmila

2012-12-01

The paper describes the manufacturing process of extruded products by the cellular extrusion method, and presents specifications of the blowing agents used in the extrusion process as well as process conditions. The process of cellular extrusion of thermoplastic materials is aimed at obtaining cellular shapes and coats with reduced density, presenting no hollows on the surface of extruder product and displaying minimal contraction under concurrent maintenance of properties similar to properties of products extruded by means of the conventional method. In order to obtain cellular structure, the properties of extruded product are modified by applying suitable plastic or inserting auxiliary agents.

Sea-floor methane blow-out and global firestorm at the K-T boundary

USGS Publications Warehouse

Max, M.D.; Dillon, William P.; Nishimura, C.; Hurdle, B.G.

1999-01-01

A previously unsuspected source of fuel for the global firestorm recorded by soot in the Cretaceous-Tertiary impact layer may have resided in methane gas associated with gas hydrate in the end-Cretaceous seafloor. End-Cretaceous impact-generated shock and megawaves would have had the potential to initiate worldwide oceanic methane gas blow-outs from these deposits. The methane would likely have ignited and incompletely combusted. This large burst of methane would have been followed by longer-term methane release as a part of a positive thermal feedback in the disturbed ocean-atmosphere system.

Phenomenological implications of the blown-up orbifolds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cvetic, M.

1987-05-01

We discuss the structure of the effective Lagrangian for the (2,2) Z/sub N/ orbifolds and the corresponding Calabi-Yau manifolds which are obtained by ''blowing-up'' the orbifold singularities. The method to ''blow-up'' such singularities is reviewed. Results are exact at the string tree-level. In particular, the question of generating an intermediate scale M/sub I/ in such models is addressed. It is shown that for Z/sub N/ orbifolds (except one) and the corresponding blown-up orbifolds which are compactified on any six-torus T/sup 6/ which can be obtained by continuously deforming T/sup 4/ circle times T/sup 2/, all the terms of the typemore » (2727)/sup K/ are absent from the effective superpotential, thus questioning the mechanism for generating a large intermediate scale for such compactifications.« less

Noise annoyance through railway traffic - a case study.

PubMed

Trombetta Zannin, Paulo Henrique; Bunn, Fernando

2014-01-08

This paper describes an assessment of noise caused by railway traffic in a large Latin American city. Measurements were taken of noise levels generated by trains passing through residential neighborhoods with and without blowing their horns. Noise maps were also calculated showing noise pollution generated by the train traffic. In addition - annoyance of the residents - affected by railway noise, was evaluated based on interviews. The measurements indicated that the noise levels generated by the passage of the train with its horn blowing are extremely high, clearly exceeding the daytime limits of equivalent sound pressure level - Leq = 55 dB(A) - established by the municipal laws No 10.625 of the city of Curitiba. The Leq = 45 dB (A) which is the limit for the night period also are exceeded during the passage of trains. The residents reported feeling affected by the noise generated by passing trains, which causes irritability, headaches, poor concentration and insomnia, and 88% of them claimed that nocturnal noise pollution is the most distressing. This study showed that the vast majority of residents surveyed, (69%) believe that the noise of the train can devalue their property.

End-functionalized ROMP polymers for Biomedical Applications

PubMed Central

Madkour, Ahmad E.; Koch, Amelie H. R.; Lienkamp, Karen; Tew, Gregory N.

2010-01-01

We present two novel allyl-based terminating agents that can be used to end-functionalize living polymer chains obtained by ring-opening metathesis polymerization (ROMP) using Grubbs’ third generation catalyst. Both terminating agents can be easily synthesized and yield ROMP polymers with stable, storable activated ester groups at the chain-end. These end-functionalized ROMP polymers are attractive building blocks for advanced polymeric materials, especially in the biomedical field. Dye-labeling and surface-coupling of antimicrobially active polymers using these end-groups were demonstrated. PMID:21499549

Soft Lithography for Oligonucleotide Arrays Fabrication

DTIC Science & Technology

2001-10-25

adenosine; Abbreviated T, C, G, A respectively), the other synthesis reagents and solvents except oxidation agent (seen in Table 1) were purchased...dried by cold blowing before hybridization. Oligonucleotide arrays were hybridized in 200 nM 3’-TCC TCC GAT TCA GAG AGT CC- HEX (PE Biosystems... citrate buffer), 0.1% SDS in 0.1xSSC respectively. The probe array was scanned on the Scanarray Microarray Systems (Packard Biochip Technologies, USA

Performance Versus Safety of Some Primary and Rechargeable Lithium Batteries

DTIC Science & Technology

2004-12-01

which can ignite during abuse. At the same time, manganese dioxide is an oxidising agent and it decomposes at 535oC, giving off oxygen, thus...is endothermic for nicad but exothermic for nickel- metal hydride. Therefore, nickel-metal hydride cells are more prone to damage from...With nail penetration, Figure 6. Photograph showing damage inflicted onto a lithium-ion gel-polymer cell by several hammer blows

Project SQUID. Quarterly Progress Report

DTIC Science & Technology

1948-10-01

cata- lysts imbedded in the liner walls, and endothermic diffusion processes. Summary The paper entitled Heat Transfer in Laminar Boundary Layer...in mixture strength must be effected up to that required for maximum heat release to prevent blow -off of the annu- lus flame. It is possible to...these films. An X-ray diffraction investigation of the effect of polishing agent on the character of oxidation product has been started. Samples

Polyurethane foams obtained from residues of PET manufacturing and modified with carbon nanotubes

NASA Astrophysics Data System (ADS)

Stiebra, L.; Cabulis, U.; Knite, M.

2016-04-01

In this work we report the preparation of rigid microcellular polyurethane/carbon nanotube nanocomposites with different CNT loadings (0.09-0.46%) and various isocyanate indexes (110-260). Water was used as a blowing agent for samples. Density of all obtained samples - 200 ± 10 kg/m3. Electrical properties, as well as heat conductivity, cellular structure and mechanical properties of these nanocomposites were investigated.

Source identification and apportionment of halogenated compounds observed at a remote site in East Asia.

PubMed

Li, Shanlan; Kim, Jooil; Park, Sunyoung; Kim, Seung-Kyu; Park, Mi-Kyung; Mühle, Jens; Lee, Gangwoong; Lee, Meehye; Jo, Chun Ok; Kim, Kyung-Ryul

2014-01-01

The sources of halogenated compounds in East Asia associated with stratospheric ozone depletion and climate change are relatively poorly understood. High-precision in situ measurements of 18 halogenated compounds and carbonyl sulfide (COS) made at Gosan, Jeju Island, Korea, from November 2007 to December 2011 were analyzed by a positive matrix factorization (PMF). Seven major industrial sources were identified from the enhanced concentrations of halogenated compounds observed at Gosan and corresponding concentration-based source contributions were also suggested: primary aluminum production explaining 37% of total concentration enhancements, solvent usage of which source apportionment is 25%, fugitive emissions from HCFC/HFC production with 11%, refrigerant replacements (9%), semiconductor/electronics industry (9%), foam blowing agents (6%), and fumigation (3%). Statistical trajectory analysis was applied to specify the potential emission regions for seven sources using back trajectories. Primary aluminum production, solvent usage and fugitive emission sources were mainly contributed by China. Semiconductor/electronics sources were dominantly located in Korea. Refrigerant replacement, fumigation and foam blowing agent sources were spread throughout East Asian countries. The specified potential source regions are consistent with country-based consumptions and emission patterns, verifying the PMF analysis results. The industry-based emission sources of halogenated compounds identified in this study help improve our understanding of the East Asian countries' industrial contributions to halogenated compound emissions.

The effects of foaming conditions on plasticized polyvinyl chloride foam morphology by using liquid carbon dioxide

NASA Astrophysics Data System (ADS)

Chuaponpat, N.; Areerat, S.

2017-11-01

This research studies the effects of foaming conditions by using liquid carbon dioxide (CO2) as a physical blowing agent on plasticized polyvinyl chloride (PVC) foam morphology. Foaming conditions were soaking time of 6, 10, and 12 h, foaming temperature of 70, 80, 90 °C for 5 s, at constant soaking temperature of -20 °C and pressure of 50 bar. Instantaneously increasing temperature was employed in this process for making foam structure. PVC foam samples were calculated percentage of shrinkage (Sh) by using density at before and after aging process at 30 °C for 12 h. When PVC samples were activated to form foam by using liquid CO2 as a physical blowing agent, it reveal bimodal foam structure with a thick bubble wall (10-20 μm). Bubble diameter of PVC foam at longer soaking time is in the range of 40-60 μm and its at shorter soaking time reveal a large bubble that is in the range of 80-120 μm. Foaming condition slightly affected to bubble density that was in the narrow range of 106-108 bubbles/cm3. PVC foam reveal reduction of density up to 65% when compare with PVC and Sh is less than 10%.

Deformation and Plateau Region of Functionally Graded Aluminum Foam by Amount Combinations of Added Blowing Agent.

PubMed

Hangai, Yoshihiko; Utsunomiya, Takao; Kuwazuru, Osamu; Kitahara, Soichiro; Yoshikawa, Nobuhiro

2015-10-21

Recently, to further improve the performance of aluminum foam, functionally graded (FG) aluminum foams, whose pore structure varies with their position, have been developed. In this study, three types of FG aluminum foam of aluminum alloy die casting ADC12 with combinations of two different amounts of added blowing agent titanium(II) hydride (TiH₂) powder were fabricated by a friction stir welding (FSW) route precursor foaming method. The combinations of 1.0-0 mass %, 0.4-0 mass %, and 0.2-0 mass % TiH₂ were selected as the amounts of TiH₂ relative to the mass of the volume stirred by FSW. The static compression tests of the fabricated FG aluminum foams were carried out. The deformation and fracture of FG aluminum foams fundamentally started in the high-porosity (with TiH₂ addition) layer and shifted to the low-porosity (without TiH₂ addition) layer. The first and second plateau regions in the relationship between compressive stress and strain independently appeared with the occurrence of deformations and fractures in the high- and low-porosity layers. It was shown that FG aluminum foams, whose plateau region varies in steps by the combination of amounts of added TiH₂ ( i.e. , the combination of pore structures), can be fabricated.

Turbulent transition behavior in a separated and attached-flow low pressure turbine passage

NASA Astrophysics Data System (ADS)

Memory, Curtis L.

Various time accurate numerical simulations were conducted on the aft-loaded L1A low pressure turbine airfoil operating at Reynolds numbers presenting with fully-stalled, non-reattaching laminar separation. The numerical solver TURBO was modified from its annular gas turbine simulation configuration to conduct simulations based on a linear cascade wind tunnel facility. Simulation results for the fully separated flow fields revealed various turbulent decay mechanisms. Separated shear layer decay, in the form of vortices forming between the shear layer and the blade wall, was shown to agree with experimental particle image velocimetry (PIV) data in terms of decay vortex size and core vorticity levels. These vortical structures eventually mix into a large recirculation zone which dominates the blade wake. Turbulent wake ex- tent and time-averaged velocity distributions agreed with PIV data. Steady-blowing vortex generating jet (VGJ) flow control was then applied to the flow fields. VGJ-induced streamwise vorticity was only present at blowing ratios above 1.5. VGJs actuated at the point of flow separation on the blade wall were more effective than those actuated downstream, within the separation zone. Pulsed-blowing VGJs at the upstream blade wall position were then actuated at various pulsing frequencies, duty cycles, and blowing ratios. These condition variations yielded differing levels of separation zone mitigation. Pulsed VGJs were shown to be more effective than steady blowing VGJs at conditions of high blowing ratio, high frequency, or high duty cycle, where blowing ratio had the highest level of influence on pulsed jet efficacy. The characteristic "calm zone" following the end of a given VGJ pulse was observed in simulations exhibiting high levels of separation zone mitigation. Numerical velocity fields near the blade wall during this calm zone was shown to be similar to velocity fields observed in PIV data. Instantaneous numerical vorticity fields indicated that the elimination of the separation zone directly downstream of the VGJ hole is a pri- mary indicator of pulsed VGJ efficacy. This indicator was confirmed by numerical time-averaged velocity magnitude rms data in the same region.

Plasma Wake-field Acceleration in the Blow-out Regime

NASA Astrophysics Data System (ADS)

Barov, Nikolai; Rosenzweig, James

1999-11-01

Recent experiments at Argonne National Laboratory, investigating the blow-out regime of the plasma wake-field accelerator, are discussed. These experiments achieved stable underdense (beam denser than the ambient plasma density) beam transport, and measured average acceleration of 25 MV/m, corresponding to peak wave fields of over 60 MVm. A comparison of the results to simulation is given, and the physics of the system is discussed. Potential for improvements in performance and achieved acceleration gradient, as well as accelerated beam quality are examined within the context of the next generation of experiments at the Fermilab Test Facility. The status of these experiments will be given.

PBSM3D: A finite volume, scalar-transport blowing snow model for use with variable resolution meshes

NASA Astrophysics Data System (ADS)

Marsh, C.; Wayand, N. E.; Pomeroy, J. W.; Wheater, H. S.; Spiteri, R. J.

2017-12-01

Blowing snow redistribution results in heterogeneous snowcovers that are ubiquitous in cold, windswept environments. Capturing this spatial and temporal variability is important for melt and runoff simulations. Point scale blowing snow transport models are difficult to apply in fully distributed hydrological models due to landscape heterogeneity and complex wind fields. Many existing distributed snow transport models have empirical wind flow and/or simplified wind direction algorithms that perform poorly in calculating snow redistribution where there are divergent wind flows, sharp topography, and over large spatial extents. Herein, a steady-state scalar transport model is discretized using the finite volume method (FVM), using parameterizations from the Prairie Blowing Snow Model (PBSM). PBSM has been applied in hydrological response units and grids to prairie, arctic, glacier, and alpine terrain and shows a good capability to represent snow redistribution over complex terrain. The FVM discretization takes advantage of the variable resolution mesh in the Canadian Hydrological Model (CHM) to ensure efficient calculations over small and large spatial extents. Variable resolution unstructured meshes preserve surface heterogeneity but result in fewer computational elements versus high-resolution structured (raster) grids. Snowpack, soil moisture, and streamflow observations were used to evaluate CHM-modelled outputs in a sub-arctic and an alpine basin. Newly developed remotely sensed snowcover indices allowed for validation over large basins. CHM simulations of snow hydrology were improved by inclusion of the blowing snow model. The results demonstrate the key role of snow transport processes in creating pre-melt snowcover heterogeneity and therefore governing post-melt soil moisture and runoff generation dynamics.

Formation of soap bubbles by gas jet

NASA Astrophysics Data System (ADS)

Zhou, Maolei; Li, Min; Chen, Zhiyuan; Han, Jifeng; Liu, Dong

2017-12-01

Soap bubbles can be easily generated by various methods, while their formation process is complicated and still worth studying. A model about the bubble formation process was proposed in the study by Salkin et al. [Phys. Rev. Lett. 116, 077801 (2016)] recently, and it was reported that the bubbles were formed when the gas blowing velocity was above one threshold. However, after a detailed study of these experiments, we found that the bubbles could be generated in two velocity ranges which corresponded to the laminar and turbulent gas jet, respectively, and the predicted threshold was only effective for turbulent gas flow. The study revealed that the bubble formation was greatly influenced by the aerodynamics of the gas jet blowing to the film, and these results will help to further understand the formation mechanism of the soap bubble as well as the interaction between the gas jet and the thin liquid film.

Fabrication of a high-density nano-porous structure on polyimide by using ultraviolet laser irradiation

NASA Astrophysics Data System (ADS)

Ma, Yong-Won; Jeong, Myung Yung; Lee, Sang-Mae; Shin, Bo Sung

2016-03-01

A new approach for fabricating a high-density nano-porous structure on polyimide (PI) by using a 355-nm UV laser is presented here. When PI was irradiated by using a laser, debris that had electrical conductivity was generated. Accordingly, that debris caused electrical defects in the field of electronics. Thus, many researchers have tried to focus on a clean processing without debris. However, this study focused on forming a high density of debris so as to fabricate a nano-porous structure consisting of nanofibers on the PI film. A PI film with closed pores and open pores was successfully formed by using a chemical blowing agent (azodicarbonamide, CBA) in an oven. Samples were precured at 130 °C and cured at 205 °C in sequence so that the closed pores might not coalesce in the film. When the laser irradiated the PI film with closed pores, nanofibers were generated because polyimide was not completely decomposed by photochemical ablation. Our results indicated that a film with micro-closed pores, in conjunction with a 355-nm pulsed laser, can facilitate the fabrication of a high-density nano-porous structure.

Polymeric foams from cross-linkable poly-N-ary lenebenzimidazoles

NASA Technical Reports Server (NTRS)

Harrison, E. S.; Delano, C. B.; Riccitello, S. R. (Inventor)

1978-01-01

Foamed cross-linked poly-N-arylenebinzimidazoles are prepared by mixing an organic tetraamine and an ortho substituted aromatic dicarboxylic acid anhydride in the presence of a blowing agent, and then heating the prepolymer to a temperature sufficient to complete polymerization and foaming of the reactants. In another embodiment of the process, the reactants are heated to form a prepolymer. The prepolymer is then cured at higher temperatures to complete foaming and polymerization.

Large Bright Ripples

NASA Technical Reports Server (NTRS)

2004-01-01

3 February 2004 Wind is the chief agent of change on Mars today. Wind blows dust and it can move coarser sediment such as sand and silt. This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows bright ripples or small dunes on the floors of troughs northeast of Isidis Planitia near 31.1oN, 244.6oW. The picture covers an area 3 km (1.9 mi) wide; sunlight illuminates the scene from the lower left.

Fluorescence Imaging of Posterior Spiracles from Second and Third Instars of Forensically-important Chrysomya rufifacies (Diptera: Calliphoridae)*

PubMed Central

Flores, Danielle; Miller, Amy L.; Showman, Angelique; Tobita, Caitlyn; Shimoda, Lori M.N.; Sung, Carl; Stokes, Alexander J.; Tomberlin, Jeffrey K.; Carter, David O.; Turner, Helen

2016-01-01

Entomological protocols for aging blow fly (Diptera: Calliphoridae) larvae to estimate the time of colonization (TOC) are commonly used to assist in death investigations. While the methodologies for analysing fly larvae differ, most rely on light microscopy, genetic analysis or, more rarely, electron microscopy. This pilot study sought to improve resolution of larval stage in the forensically-important blow fly Chrysomya rufifacies using high-content fluorescence microscopy and biochemical measures of developmental marker proteins. We established fixation and mounting protocols, defined a set of measurable morphometric criteria and captured developmental transitions of 2nd instar to 3rd instar using both fluorescence microscopy and anti-ecdysone receptor Western blot analysis. The data show that these instars can be distinguished on the basis of robust, non-bleaching, autofluorescence of larval posterior spiracles. High content imaging techniques using confocal microscopy, combined with morphometric and biochemical techniques, may therefore aid forensic entomologists in estimating TOC. PMID:27706817

Delta wing vortex manipulation using pulsed and steady blowing during ramp pitching

NASA Technical Reports Server (NTRS)

Moreira, J.; Johari, H.

1995-01-01

The effectiveness of steady and pulsed blowing as a method of controlling delta wing vortices during ramp pitching has been investigated in flow visualization experiments conducted in a water tunnel. The recessed angled spanwise blowing technique was utilized for vortex manipulation. This technique was implemented on a beveled 60 delta wing using a pair of blowing ports located beneath the vortex core at 40% chord. The flow was injected primarily in the spanwise direction but was also composed of a component normal to the wing surface. The location of vortex burst was measured as a function of blowing intensity and pulsing frequency under static conditions, and the optimum blowing case was applied at three different wing pitching rates. Experimental results have shown that, when the burst location is upstream of the blowing port, pulsed blowing delays vortex breakdown in static and dynamic cases. Dynamic tests verified the existence of a hysteresis effect and demonstrated the improvements offered by pulsed blowing over both steady blowing and no-blowing scenarios. The application of blowing, at the optimum pulsing frequency, made the vortex breakdown location comparable in static and ramp pitch-up conditions.

Blowing momentum and duty cycle effect on aerodynamic performance of flap by pulsed blowing

NASA Astrophysics Data System (ADS)

Zhou, Ping; Wang, Yankui; Wang, Jinjun; Sha, Yongxiang

2017-04-01

Control surface, which is often located in the trailing edge of wings, is important in the attitude control of an aircraft. However, the efficiency of the control surface declines severely under the high deflect angle of the control surface because of the flow separation. To improve the efficiency of control surface, this study discusses a flow-control technique aimed at suppressing the flow separation by pulsed blowing at the leading edge of the control surface. Results indicated that flow separation over the control surface can be suppressed by pulsed blowing, and the maximum average lift coefficient of the control surface can be 95% times higher than that of without blowing when average blowing momentum coefficient is 0.03 relative to that of without blowing. Finally, this study shows that the average blowing momentum coefficient and non-dimensional frequency of pulsed blowing are two of the key parameters of the pulsed blowing control technique. Otherwise, duty cycle also has influence on the effect of pulsed blowing. Numerical simulation is used in this study.

Control of Cavity Resonance Using Oscillatory Blowing

NASA Technical Reports Server (NTRS)

Scarfe, Alison Lamp; Chokani, Ndaona

2000-01-01

The near-zero net mass oscillatory blowing control of a subsonic cavity flow has been experimentally investigated. An actuator was designed and fabricated to provide both steady and oscillatory blowing over a range of blowing amplitudes and forcing frequencies. The blowing was applied just upstream of the cavity front Wall through interchangeable plate configurations These configurations enabled the effects of hole size, hole shape, and blowing angle to be examined. A significant finding is that in terms of the blowing amplitude, the near zero net mass oscillatory blowing is much more effective than steady blowing; momentum coefficients Lip two orders of magnitude smaller than those required for steady blowing are sufficient to accomplish the same control of cavity resonance. The detailed measurements obtained in the experiment include fluctuating pressure data within the cavity wall, and hot-wire measurements of the cavity shear layer. Spectral and wavelet analysis techniques are applied to understand the dynamics and mechanisms of the cavity flow with control. The oscillatory blowing, is effective in enhancing the mixing in the cavity shear layer and thus modifying the feedback loop associated with the cavity resonance. The nonlinear interactions in the cavity flow are no longer driven by the resonant cavity modes but by the forcing associated with the oscillatory blowing. The oscillatory blowing does not suppress the mode switching behavior of the cavity flow, but the amplitude modulation is reduced.

Aerodynamic control of NASP-type vehicles through Vortex manipulation. Volume 1: Static water tunnel tests

NASA Technical Reports Server (NTRS)

Suarez, Carlos J.; Ng, T. Terry; Ong, Lih-Yenn; Malcolm, Gerald N.

1993-01-01

Water tunnel tests were conducted on a NASP-type configuration to evaluate different pneumatic Forebody Vortex Control (FVC) methods. Flow visualization and yawing moment measurements were performed at angles of attack from 0 deg to 30 deg. The pneumatic techniques tested included jet and slot blowing. In general, blowing can be used efficiently to manipulate the forebody vortices at angles of attack greater than 20 deg. These vortices are naturally symmetric up to alpha = 25 deg and asymmetric between 25 deg and 30 deg angle of attack. Results indicate that tangential aft jet blowing is the most promising method for this configuration. Aft jet blowing produces a yawing moment towards the blowing side and the trends with blowing rate are well behaved. The size of the nozzle is not the dominant factor in the blowing process; the change in the blowing 'momentum,' i.e., the product of the mass flow rate and the velocity of the jet, appears to be the important parameter in the water tunnel (incompressible and unchoked flow at the nozzle exit). Forward jet blowing is very unpredictable and sensitive to mass flow rate changes. Slot blowing (with the exception of very low blowing rates) acts as a flow 'separator'; it promotes early separation on the blow side, producing a yawing moment toward the non-blowing side for the C(sub mu) range investigated.

Noise annoyance through railway traffic - a case study

PubMed Central

2014-01-01

This paper describes an assessment of noise caused by railway traffic in a large Latin American city. Measurements were taken of noise levels generated by trains passing through residential neighborhoods with and without blowing their horns. Noise maps were also calculated showing noise pollution generated by the train traffic. In addition - annoyance of the residents - affected by railway noise, was evaluated based on interviews. The measurements indicated that the noise levels generated by the passage of the train with its horn blowing are extremely high, clearly exceeding the daytime limits of equivalent sound pressure level - Leq = 55 dB(A) - established by the municipal laws No 10.625 of the city of Curitiba. The Leq = 45 dB (A) which is the limit for the night period also are exceeded during the passage of trains. The residents reported feeling affected by the noise generated by passing trains, which causes irritability, headaches, poor concentration and insomnia, and 88% of them claimed that nocturnal noise pollution is the most distressing. This study showed that the vast majority of residents surveyed, (69%) believe that the noise of the train can devalue their property. PMID:24401735

Advancements in dynamic kill calculations for blowout wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kouba, G.E.; MacDougall, G.R.; Schumacher, B.W.

1993-09-01

This paper addresses the development, interpretation, and use of dynamic kill equations. To this end, three simple calculation techniques are developed for determining the minimum dynamic kill rate. Two techniques contain only single-phase calculations and are independent of reservoir inflow performance. Despite these limitations, these two methods are useful for bracketing the minimum flow rates necessary to kill a blowing well. For the third technique, a simplified mechanistic multiphase-flow model is used to determine a most-probable minimum kill rate.

Militarization of Energy Security: Turkey as a Case Study

DTIC Science & Technology

2010-06-01

diplomats 22 Sep 1987 U.S. ship attacks and captures Iranian mine-laying vessel with mines on board 8–22 Oct 1987 U.S. sinks three Iranian patrol...U.S. blows up two Iranian oilrigs, destroys an Iranian frigate and immobilizes another. American warships sink six Iranian vessels 3 Jul 1988 USS...Libya, Romania, and Maldives ) and none of them attempted to participate in the war. The incentive for third parties to enter the war was not strong

Soot blower using fuel gas as blowing medium

DOEpatents

Tanca, Michael C.

1982-01-01

A soot blower assembly (10) for use in combination with a coal gasifier (14). The soot blower assembly is adapted for use in the hot combustible product gas generated in the gasifier as the blowing medium. The soot blower lance (20) and the drive means (30) by which it is moved into and out of the gasifier is housed in a gas tight enclosure (40) which completely surrounds the combination. The interior of the enclosure (40) is pressurized by an inert gas to a pressure level higher than that present in the gasifier so that any combustible product gas leaking from the soot blower lance (20) is forced into the gasifier rather than accumulating within the enclosure.

Discovery and Pre-Clinical Characterization of Third-Generation 4-H Heteroaryldihydropyrimidine (HAP) Analogues as Hepatitis B Virus (HBV) Capsid Inhibitors.

PubMed

Qiu, Zongxing; Lin, Xianfeng; Zhang, Weixing; Zhou, Mingwei; Guo, Lei; Kocer, Buelent; Wu, Guolong; Zhang, Zhisen; Liu, Haixia; Shi, Houguang; Kou, Buyu; Hu, Taishan; Hu, Yimin; Huang, Mengwei; Yan, S Frank; Xu, Zhiheng; Zhou, Zheng; Qin, Ning; Wang, Yue Fen; Ren, Shuang; Qiu, Hongxia; Zhang, Yuxia; Zhang, Yi; Wu, Xiaoyue; Sun, Kai; Zhong, Sheng; Xie, Jianxun; Ottaviani, Giorgio; Zhou, Yuan; Zhu, Lina; Tian, Xiaojun; Shi, Liping; Shen, Fang; Mao, Yi; Zhou, Xue; Gao, Lu; Young, John A T; Wu, Jim Zhen; Yang, Guang; Mayweg, Alexander V; Shen, Hong C; Tang, Guozhi; Zhu, Wei

2017-04-27

Described herein are the discovery and structure-activity relationship (SAR) studies of the third-generation 4-H heteroaryldihydropyrimidines (4-H HAPs) featuring the introduction of a C6 carboxyl group as novel HBV capsid inhibitors. This new series of 4-H HAPs showed improved anti-HBV activity and better drug-like properties compared to the first- and second-generation 4-H HAPs. X-ray crystallographic study of analogue 12 (HAP_R01) with Cp149 Y132A mutant hexamer clearly elucidated the role of C6 carboxyl group played for the increased binding affinity, which formed strong hydrogen bonding interactions with capsid protein and coordinated waters. The representative analogue 10 (HAP_R10) was extensively characterized in vitro (ADMET) and in vivo (mouse PK and PD) and subsequently selected for further development as oral anti-HBV infection agent.

A historical look at chlorofluorocarbon refrigerants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatti, M.S.

1999-07-01

A class of chemical compounds called chlorofluorocarbon refrigerants has been in widespread use since the 1930s in such diverse applications as refrigerants for refrigerating and air-conditioning systems, blowing agents for plastic foams, solvents for microelectronic circuitry and dry cleaning, sterilants for medical instruments, aerosol propellants for personal hygiene products and pesticides, and freezants for food. This paper describes the historical development of the chlorofluorocarbon refrigerants and gives brief biographical sketches of the inventors. 85 refs., 8 figs., 4 tabs.

Development of analysis technique to predict the material behavior of blowing agent

NASA Astrophysics Data System (ADS)

Hwang, Ji Hoon; Lee, Seonggi; Hwang, So Young; Kim, Naksoo

2014-11-01

In order to numerically simulate the foaming behavior of mastic sealer containing the blowing agent, a foaming and driving force model are needed which incorporate the foaming characteristics. Also, the elastic stress model is required to represent the material behavior of co-existing phase of liquid state and the cured polymer. It is important to determine the thermal properties such as thermal conductivity and specific heat because foaming behavior is heavily influenced by temperature change. In this study, three models are proposed to explain the foaming process and material behavior during and after the process. To obtain the material parameters in each model, following experiments and the numerical simulations are performed: thermal test, simple shear test and foaming test. The error functions are defined as differences between the experimental measurements and the numerical simulation results, and then the parameters are determined by minimizing the error functions. To ensure the validity of the obtained parameters, the confirmation simulation for each model is conducted by applying the determined parameters. The cross-verification is performed by measuring the foaming/shrinkage force. The results of cross-verification tended to follow the experimental results. Interestingly, it was possible to estimate the micro-deformation occurring in automobile roof surface by applying the proposed model to oven process analysis. The application of developed analysis technique will contribute to the design with minimized micro-deformation.

Deformation and Plateau Region of Functionally Graded Aluminum Foam by Amount Combinations of Added Blowing Agent

PubMed Central

Hangai, Yoshihiko; Utsunomiya, Takao; Kuwazuru, Osamu; Kitahara, Soichiro; Yoshikawa, Nobuhiro

2015-01-01

Recently, to further improve the performance of aluminum foam, functionally graded (FG) aluminum foams, whose pore structure varies with their position, have been developed. In this study, three types of FG aluminum foam of aluminum alloy die casting ADC12 with combinations of two different amounts of added blowing agent titanium(II) hydride (TiH2) powder were fabricated by a friction stir welding (FSW) route precursor foaming method. The combinations of 1.0–0 mass %, 0.4–0 mass %, and 0.2–0 mass % TiH2 were selected as the amounts of TiH2 relative to the mass of the volume stirred by FSW. The static compression tests of the fabricated FG aluminum foams were carried out. The deformation and fracture of FG aluminum foams fundamentally started in the high-porosity (with TiH2 addition) layer and shifted to the low-porosity (without TiH2 addition) layer. The first and second plateau regions in the relationship between compressive stress and strain independently appeared with the occurrence of deformations and fractures in the high- and low-porosity layers. It was shown that FG aluminum foams, whose plateau region varies in steps by the combination of amounts of added TiH2 (i.e., the combination of pore structures), can be fabricated. PMID:28793626

A Basic Study on Countermeasure Against Aerodynamic Force Acting on Train Running Inside Tunnel Using Air Blowing

NASA Astrophysics Data System (ADS)

Suzuki, Masahiro; Nakade, Koji

A basic study of flow controls using air blowing was conducted to reduce unsteady aerodynamic force acting on trains running in tunnels. An air blowing device is installed around a model car in a wind tunnel. Steady and periodic blowings are examined utilizing electromagnetic valves. Pressure fluctuations are measured and the aerodynamic force acting on the car is estimated. The results are as follows: a) The air blowing allows reducing the unsteady aerodynamic force. b) It is effective to blow air horizontally at the lower side of the car facing the tunnel wall. c) The reduction rate of the unsteady aerodynamic force relates to the rate of momentum of the blowing to that of the uniform flow. d) The periodic blowing with the same frequency as the unsteady aerodynamic force reduces the aerodynamic force in a manner similar to the steady blowing.

An investigation of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack. M.S. Thesis

NASA Technical Reports Server (NTRS)

Gittner, Nathan M.

1992-01-01

An experimental investigation of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was investigated. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were investigated and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Unsteady High Turbulence Effects on Turbine Blade Film Cooling Heat Transfer Performance Using a Transient Liquid Crystal Technique

NASA Technical Reports Server (NTRS)

Han, J. C.; Ekkad, S. V.; Du, H.; Teng, S.

2000-01-01

Unsteady wake effect, with and without trailing edge ejection, on detailed heat transfer coefficient and film cooling effectiveness distributions is presented for a downstream film-cooled gas turbine blade. Tests were performed on a five-blade linear cascade at an exit Reynolds number of 5.3 x 10(exp 5). Upstream unsteady wakes were simulated using a spoke-wheel type wake generator. Coolant blowing ratio was varied from 0.4 to 1.2; air and CO2 were used as coolants to simulate different density ratios. Surface heat transfer and film effectiveness distributions were obtained using a transient liquid crystal technique; coolant temperature profiles were determined with a cold wire technique. Results show that Nusselt numbers for a film cooled blade are much higher compared to a blade without film injection. Unsteady wake slightly enhances Nusselt numbers but significantly reduces film effectiveness versus no wake cases. Nusselt numbers increase only slic,htly but film cooling, effectiveness increases significantly with increasing, blowing ratio. Higher density coolant (CO2) provides higher effectiveness at higher blowing ratios (M = 1.2) whereas lower density coolant (Air) provides higher 0 effectiveness at lower blowing ratios (M = 0.8). Trailing edge ejection generally has more effect on film effectiveness than on the heat transfer, typically reducing film effectiveness and enhancing heat transfer. Similar data is also presented for a film cooled cylindrical leading edge model.

Electric field measurements during the blowing snow in a cryogenic wind tunnel by a non-contact voltmeter

NASA Astrophysics Data System (ADS)

Sato, A.; Omiya, S.

2011-12-01

It is known that the average atmospheric electric field is +100V/m in fair weather (positive electric field vector points downward). An increase of atmospheric electric field is reported when the blowing snow occurred. This phenomenon is mainly explained by the fact that the blowing snow particles have negative charge in average. It is suggested that an electrostatic force, given by the product of the electric field and the charge of the particle, may influence the particle trajectory and change those movements, saltation and suspension. The purpose of this experiment is to clarify the characteristics of the electric field during blowing snow event. Experiments were carried out in the cryogenic wind tunnel of Snow and Ice Research Center, NIED. A non-contact voltmeter was used to measure the electric field. An artificial blowing snow was generated by a snow particle supply machine. The rolling brushes of the machine scratch the snow surface and supply snow particles into the airflow. This machine made it possible to supply the snow particles at an arbitrary rate. This experiment was conducted in the following experimental conditions; wind speed of 5 to 7 m/s (3 patterns), supply snow quantity of 8.7 to 34.9 g/m/s (4 patterns), air temperature of -10 degree Celsius, fetch of 10 m and hard snow surface. Measured electric field was all negative, which is opposite direction to the previous measurements. This means that the blowing snow particles had positive charges. The negative electric field tended to increase with increase of the wind speed and the mass flux. These results can be explained from the previous experiment by Omiya and Sato (2010). The snow particles gain positive charges by the friction with the rolling brush which is made from polypropylene, however the particles accumulate negative charges gradually with increase of the collisions to the snow surface. Probably, the positive charges might have remained on the snow particles that had passed over the measurement point. Moreover, it is thought that because the saltation length is longer when the wind speed is higher, fewer collision frequencies left the particles more positive charges. REFERENCE:Omiya and Sato(2010): Measurement of electrostatic charge of blowing snow particles in a wind tunnel focusing on collision frequency to the snow surface. Hokkaido University Collection of Scholarly and Academic Papers

Experimental investigation of the effects of aft blowing with various nozzle exit geometries on a 3.0 caliber tangent ogive at high angles of attack: Forebody pressure distributions

NASA Technical Reports Server (NTRS)

Chokani, Ndaona; Gittner, N. M.

1992-01-01

An experimental study of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was studied. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were studied and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Tilt Nacelle Vertical and Short Takeoff and Landing Engine

NASA Image and Video Library

1979-03-21

Center Director John McCarthy, left, and researcher Al Johns pose with a one-third scale model of a Grumman Aerospace tilt engine nacelle for Vertical and Short Takeoff and Landing (V/STOL) in the 9- by 15-Foot Low Speed Wind Tunnel at the National Aeronautics and Space Administration (NASA) Lewis Research Center. Lewis researchers had been studying tilt nacelle and inlet issues for several years. One area of concern was the inlet flow separation during the transition from horizontal to vertical flight. The separation of air flow from the inlet’s internal components could significantly stress the fan blades or cause a loss of thrust. In 1978 NASA researchers Robert Williams and Al Johns teamed with Grumman’s H.C. Potonides to develop a series of tests in the Lewis 9- by 15-foot tunnel to study a device designed to delay the flow separation by blowing additional air into the inlet. A jet of air, supplied through the hose on the right, was blown over the inlet surfaces. The researchers verified that the air jet slowed the flow separation. They found that the blowing on boundary layer control resulted in a doubling of the angle-of-attack and decreases in compressor blade stresses and fan distortion. The tests were the first time the concept of blowing air for boundary layer control was demonstrated. Boundary layer control devices like this could result in smaller and lighter V/STOL inlets.

Agent-based Decision Support System for the Third Generation Distributed Dynamic Decision-making (DDD-III) Simulator

DTIC Science & Technology

2004-06-01

suitable form of organizational adaptation is effective organizational diagnosis and analysis. The organizational diagnosis and analysis involve...related to the mission environment, organizational structure, and strategy is imperative for an effective and efficient organizational diagnosis . The...not easily articulated nor expressed otherwise. These displays are crucial to facilitate effective organizational diagnosis and analysis, and

Aspects of tests and assessment of filtering materials used for respiratory protection against bioaerosols. Part I: type of active substance, contact time, microorganism species.

PubMed

Majchrzycka, Katarzyna; Gutarowska, Beata; Brochocka, Agnieszka

2010-01-01

This paper presents the results of a study on antimicrobial activity of polymer filter nonwovens produced by needle-punching or melt-blowing with an addition of disinfecting agents. The first part of the paper discusses how the biocidal activity of nonwovens is a function of the active agent added to the nonwovens, the duration of the contact of microorganisms with nonwovens and the type of microorganisms. The types of fibres and disinfecting agents had a considerable effect on the biocidal activity of nonwovens. The biocidal effect of nonwovens increased with the duration of their contact with microorganisms. Fibre activity differed considerably depending on the species of the microorganism. The microorganisms most sensitive to biocidal activity of the active filter nonwoven were S. aureus, M. flavus and E. coli. There were no biocidal effects on spore-forming bacterium B. subtilis.

22. Blow Down Valve for Unit 1, view to the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. Blow Down Valve for Unit 1, view to the southwest. This valve allows the water in the draft chest to be lowered (i.e., 'blown down') so that the unit can be motored (i.e., run like an electric motor rather than an electric power generator). The valve is operated by pressure from the instrument air system (part of which is visible in photograph MT-105-A-17 above), but the unit draws on the station air system (see photograph MT-105-A-24 below) to lower the water in the draft chest. - Washington Water Power Clark Fork River Noxon Rapids Hydroelectric Development, Powerhouse, South bank of Clark Fork River at Noxon Rapids, Noxon, Sanders County, MT

Video analysis of blows to the head and face at the 1999 World Taekwondo Championships.

PubMed

Koh, J O; Watkinson, E J

2002-09-01

Limited research has been done on head blows that may result in mild traumatic brain injury in Taekwondo. The purpose of this study was to investigate the fighting conditions under which blows to the head commonly take place, with a view to determining the typical conditions under which injury may occur. videotape analysis (retrospective). the semi-final and final matches (a total of 48 matches) at the 14th World Taekwondo Championships in 1999. 64 athletes (32 females and 32 males) who won elimination-round matches (out of 563 competitors), aged 15 to 38 years. frequency, mechanism of head blows, characteristics of situations leading up to and following head blows, frequency of multiple impacts. A total of 35 incidents of head blow occurred (365 blows per 1,000 athlete exposures). All of these head blows were associated with a direct head or face contact and frequently involved: a closed sparring stance, shorter athletes, axe or roundhouse type kicks, attacker's offensive kick, and head-blow-receiver's offensive action with absence of a blocking skill. To prevent possible brain injury resulting from direct head blows, updated safety education, a complete understanding of concussion for athletes, coaches, and referees, and a rule change in competition Taekwondo are recommended.

Rational Design, Synthesis, and Biological Evaluation of Third Generation α-Noscapine Analogues as Potent Tubulin Binding Anti-Cancer Agents

PubMed Central

Manchukonda, Naresh Kumar; Naik, Pradeep Kumar; Santoshi, Seneha; Lopus, Manu; Joseph, Silja; Sridhar, Balasubramanian; Kantevari, Srinivas

2013-01-01

Systematic screening based on structural similarity of drugs such as colchicine and podophyllotoxin led to identification of noscapine, a microtubule-targeted agent that attenuates the dynamic instability of microtubules without affecting the total polymer mass of microtubules. We report a new generation of noscapine derivatives as potential tubulin binding anti-cancer agents. Molecular modeling experiments of these derivatives 5a, 6a-j yielded better docking score (-7.252 to -5.402 kCal/mol) than the parent compound, noscapine (-5.505 kCal/mol) and its existing derivatives (-5.563 to -6.412 kCal/mol). Free energy (ΔG bind) calculations based on the linear interaction energy (LIE) empirical equation utilizing Surface Generalized Born (SGB) continuum solvent model predicted the tubulin-binding affinities for the derivatives 5a, 6a-j (ranging from -4.923 to -6.189 kCal/mol). Compound 6f showed highest binding affinity to tubulin (-6.189 kCal/mol). The experimental evaluation of these compounds corroborated with theoretical studies. N-(3-brormobenzyl) noscapine (6f) binds tubulin with highest binding affinity (KD, 38 ± 4.0 µM), which is ~ 4.0 times higher than that of the parent compound, noscapine (KD, 144 ± 1.0 µM) and is also more potent than that of the first generation clinical candidate EM011, 9-bromonoscapine (KD, 54 ± 9.1 µM). All these compounds exhibited substantial cytotoxicity toward cancer cells, with IC50 values ranging from 6.7 µM to 72.9 µM; compound 6f showed prominent anti-cancer efficacy with IC50 values ranging from 6.7 µM to 26.9 µM in cancer cells of different tissues of origin. These compounds perturbed DNA synthesis, delayed the cell cycle progression at G2/M phase, and induced apoptotic cell death in cancer cells. Collectively, the study reported here identified potent, third generation noscapinoids as new anti-cancer agents. PMID:24205049

The study of poly(L-lactide) grafted silica nanoparticles on the film blowing of poly(L-lactide)

NASA Astrophysics Data System (ADS)

Wu, Feng; Liu, Zhengying; Yang, Mingbo

2015-05-01

PLA nanocomposites are prepared by us, and to better develop the function of silica nanoparticle, the surface of silica nanoparticles are modified by introducing PLA chains via "grafting to" method in our research. According to the results of 1H NMR and TGA, it shows that the PLA grafted Silica nanoparticles are successfully synthesized by controlling the reaction condition, and the molecular weight of the grafted PLA chains is relatively as high as 22 400 g/mol. PLA Nanocomposites with modified nanoparticles are prepared using a convenient melt blending method to guarantee well-distribution of the particles. The well-dispersion state of silica nanospheres is confirmed by Scan Electrical Micrograph (SEM) technology. From the dynamic shear rheology tests, the strain and time sweep both reveal that stability networks are formed in these nanocomposites. And the frequency sweep shows that the nanoparticles with long grafted chains dramatically enhanced the storage and viscosity of the pure PLA. The rheology testing suggests that strong particle-matrix interactions between molecularly/nano-level dispersed grafted silica and PLA chains formed; and the elongational viscosity of PLA has been markedly improved with the addition of the nanoparticle. The effect of modified nanoparticles on the thermal properties of PLA has also been studied by us using Differential Scanning Calorimetry (DSC). It reveals that the crystallization rate of PLA has been improved as the long grafted chains play as the nucleation sites for PLA. Finally based on these rheology and crystallization researches, the nanocomposites are used to prepare PLA blowing films. Compared to pure PLA and PLA/unmodified silica nanocomposites, the results show that the stability of the film blowing has been greatly improved and the blow-up ratio has been increased with the addition of PLA grafted nanoparticles. The modified nanoparticles hold significant candidates to improve the thermal stability and the processability of pure PLA, especially used as special processing agent in the field of PLA stretch shaping process.

Experimental Study of Characteristics of Micro-Hole Porous Skins for Turbulent Skin Friction Reduction

NASA Technical Reports Server (NTRS)

Hwang, Danny P.

2002-01-01

Characteristics of micro-hole porous skins for the turbulent skin friction reduction technology called the micro-blowing technique (MBT) were assessed experimentally at Mach 0.4 and blowing fractions from zero to 0.005. The objective of this study was to provide guidelines for the selection of porous plates for MBT. The hole angle, pattern, diameter, aspect ratio, and porosity were the parameters considered for this study. The additional effort to angle and stagger the holes was experimentally determined to be unwarranted in terms of skin friction benefit; therefore, these parameters were systematically eliminated from the parametric study. The impact of the remaining three parameters was evaluated by fixing two parameters at the reference values while varying the third parameter. The best hole-diameter Reynolds number was found to be around 400, with an optimum aspect ratio of about 6. The optimum porosity was not conclusively discerned because the range of porosities in the test plates considered was not great enough. However, the porosity was estimated to be about 15 percent or less.

A technology path to tactical agent-based modeling

NASA Astrophysics Data System (ADS)

James, Alex; Hanratty, Timothy P.

2017-05-01

Wargaming is a process of thinking through and visualizing events that could occur during a possible course of action. Over the past 200 years, wargaming has matured into a set of formalized processes. One area of growing interest is the application of agent-based modeling. Agent-based modeling and its additional supporting technologies has potential to introduce a third-generation wargaming capability to the Army, creating a positive overmatch decision-making capability. In its simplest form, agent-based modeling is a computational technique that helps the modeler understand and simulate how the "whole of a system" responds to change over time. It provides a decentralized method of looking at situations where individual agents are instantiated within an environment, interact with each other, and empowered to make their own decisions. However, this technology is not without its own risks and limitations. This paper explores a technology roadmap, identifying research topics that could realize agent-based modeling within a tactical wargaming context.

Differentiation between Lucilia cuprina and Hemipyrellia ligurriens (Diptera: Calliphoridae) larvae for use in forensic entomology applications.

PubMed

Sukontason, Kom; Sribanditmongkol, Pongruk; Ngoen-klan, Ratchadawan; Klong-klaew, Tunwadee; Moophayak, Kittikhun; Sukontason, Kabkaew L

2010-02-01

Lucilia cuprina and Hemipyrellia ligurriens are forensically important blow flies in many countries. The immature stage, in particular the third instar, of both species are generally similar in morphological appearance. In this study, the use of three main characteristics, the posterior spiracle, the dorsal spines between the first and second thoracic segments, and the cephalopharyngeal skeleton, allows for identification of both fly species, with the number of papillae on anterior spiracle being a supportive characteristic in some cases. Comparison of these characteristics is illustrated in detail.

Extrusion foaming of protein-based thermoplastic and polyethylene blends

NASA Astrophysics Data System (ADS)

Gavin, Chanelle; Lay, Mark C.; Verbeek, Casparus J. R.

2016-03-01

Currently the extrusion foamability of Novatein® Thermoplastic Protein (NTP) is being investigated at the University of Waikato in collaboration with the Biopolymer Network Ltd (NZ). NTP has been developed from bloodmeal (>86 wt% protein), a co-product of the meat industry, by adding denaturants and plasticisers (tri-ethylene glycol and water) allowing it to be extruded and injection moulded. NTP alone does not readily foam when sodium bicarbonate is used as a chemical blowing agent as its extensional viscosity is too high. The thermoplastic properties of NTP were modified by blending it with different weight fractions of linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH) compatibiliser. Extrusion foaming was conducted in two ways, firstly using the existing water content in the material as the blowing agent and secondly by adding sodium bicarbonate. When processed in a twin screw extruder (L/D 25 and 10 mm die) the material readily expanded due to the internal moisture content alone, with a conditioned expansion ratio of up to ± 0.13. Cell structure was non-uniform exhibiting a broad range cell sizes at various stages of formation with some coalescence. The cell size reduced through the addition of sodium bicarbonate, overall more cells were observed and the structure was more uniform, however ruptured cells were also visible on the extrudate skin. Increasing die temperature and introducing water cooling reduced cell size, but the increased die temperature resulted in surface degradation.

High Temperature Structural Foam

NASA Technical Reports Server (NTRS)

Weiser, Erik S.; Baillif, Faye F.; Grimsley, Brian W.; Marchello, Joseph M.

1997-01-01

The Aerospace Industry is experiencing growing demand for high performance polymer foam. The X-33 program needs structural foam insulation capable of retaining its strength over a wide range of environmental conditions. The High Speed Research Program has a need for low density core splice and potting materials. This paper reviews the state of the art in foam materials and describes experimental work to fabricate low density, high shear strength foam which can withstand temperatures from -220 C to 220 C. Commercially available polymer foams exhibit a wide range of physical properties. Some with densities as low as 0.066 g/cc are capable of co-curing at temperatures as high as 182 C. Rohacell foams can be resin transfer molded at temperatures up to 180 C. They have moduli of elasticity of 0.19 MPa, tensile strengths of 3.7 Mpa and compressive strengths of 3.6 MPa. The Rohacell foams cannot withstand liquid hydrogen temperatures, however Imi-Tech markets Solimide (trademark) foams which withstand temperatures from -250 C to 200 C, but they do not have the required structural integrity. The research activity at NASA Langley Research Center focuses on using chemical blowing agents to produce polyimide thermoplastic foams capable of meeting the above performance requirements. The combination of blowing agents that decompose at the minimum melt viscosity temperature together with plasticizers to lower the viscosity has been used to produce foams by both extrusion and oven heating. The foams produced exhibit good environmental stability while maintaining structural properties.

Collaborative Model for Acceleration of Individualized Therapy of Colon Cancer

DTIC Science & Technology

2015-12-01

Approved for Public Release; Distribution Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Colorectal cancer (CRC) represents a major health burden...15. SUBJECT TERMS Colorectal cancer, novel anti-cancer agents, bioinformatics, next-generation sequencing, predictive biomarkers, individualized...INTRODUCTION:   Colorectal   cancer   (CRC)   represents   a  major   health  burden,   and   is   the   third   leading

TRICARE; TRICARE sanction authority for third-party billing agents. Final rule.

PubMed

2013-02-26

This final rule will provide the Director, TRICARE Management Activity (TMA), or designee, with the authority to sanction third-party billing agents by invoking the administrative remedy of exclusion or suspension from the TRICARE program. Such sanctions may be invoked in situations involving fraud or abuse on the part of third-party billing agents that prepare or submit claims presented to TRICARE for payment.

Experiments in Aircraft Roll-Yaw Control using Forebody Tangential Blowing

NASA Technical Reports Server (NTRS)

Pedreiro, Nelson

1997-01-01

Advantages of flight at high angles of attack include increased maneuverability and lift capabilities. These are beneficial not only for fighter aircraft, but also for future supersonic and hypersonic transport aircraft during take-off and landing. At high angles of attack the aerodynamics of the vehicle are dominated by separation, vortex shedding and possibly vortex breakdown. These phenomena severely compromise the effectiveness of conventional control surfaces. As a result, controlled flight at high angles of attack is not feasible for current aircraft configurations. Alternate means to augment the control of the vehicle at these flight regimes are therefore necessary. The present work investigates the augmentation of an aircraft flight control system by the injection of a thin sheet of air tangentially to the forebody of the vehicle. This method, known as Forebody Tangential Blowing (FTB), has been proposed as an effective means of increasing the controllability of aircraft at high angles of attack. The idea is based on the fact that a small amount of air is sufficient to change the separation lines on the forebody. As a consequence, the strength and position of the vortices are altered causing a change on the aerodynamic loads. Although a very effective actuator, forebody tangential blowing is also highly non-linear which makes its use for aircraft control very difficult. In this work, the feasibility of using FTB to control the roll-yaw motion of a wind tunnel model was demonstrated both through simulations and experimentally. The wind tunnel model used in the experiments consists of a wing-body configuration incorporating a delta wing with 70-degree sweep angle and a cone-cylinder fuselage. The model is equipped with forebody slots through which blowing is applied. There are no movable control surfaces, therefore blowing is the only form of actuation. Experiments were conducted at a nominal angle of attack of 45 degrees. A unique apparatus that constrains the model to two degrees-of-freedom, roll and yaw, was designed and built. The apparatus was used to conduct dynamic experiments which showed that the system was unstable, its natural motion divergent. A model for the unsteady aerodynamic loads was developed based on the basic physics of the flow and results from flow visualization experiments. Parameters of the aerodynamic model were identified from experimental data. The model was validated using data from dynamic experiments. The aerodynamic model completes the equations of motion of the system which were used in the design of control laws using blowing as the only actuator. The unsteady aerodynamic model was implemented as part of the real-time vehicle control system. A control strategy using asymmetric blowing was demonstrated experimentally. A discrete vortex method was developed to help understand the main physics of the flow. The method correctly captures the interactions between forebody and wing vortices. Moreover, the trends in static loads and flow structure are correctly represented. Flow visualization results revealed the vortical structure of the flow to be asymmetric even for symmetric flight conditions. The effects of blowing, and roll and yaw angles on the flow structure were determined. It is shown that superimposing symmetric and asymmetric blowing has a linearizing effect on the actuator characteristics. Transient responses of roll and yaw moments to step input blowing were characterized, and their differences were explained based on the physical mechanisms through which these loads are generated.

Whistle-Blowing Intentions of Prospective Teachers: Education Evidence

ERIC Educational Resources Information Center

Gökçe, Asiye Toker

2013-01-01

This study investigates whistle-blowing intentions of prospective teachers. Firstly, overall ethical awareness of the participants was examined, and then their underlying ethical reasons of whistle-blowing were investigated. Besides, impact on the intention to blow whistle to internal or external parties offering their job guarantee were searched.…

21 CFR 868.5220 - Blow bottle.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Blow bottle. 868.5220 Section 868.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5220 Blow bottle. (a) Identification. A blow bottle is a device...

21 CFR 868.5220 - Blow bottle.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Blow bottle. 868.5220 Section 868.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5220 Blow bottle. (a) Identification. A blow bottle is a device...

21 CFR 868.5220 - Blow bottle.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Blow bottle. 868.5220 Section 868.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5220 Blow bottle. (a) Identification. A blow bottle is a device...

21 CFR 868.5220 - Blow bottle.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Blow bottle. 868.5220 Section 868.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5220 Blow bottle. (a) Identification. A blow bottle is a device...

Propagation of Respiratory Aerosols by the Vuvuzela

PubMed Central

Lai, Ka-Man; Bottomley, Christian; McNerney, Ruth

2011-01-01

Vuvuzelas, the plastic blowing horns used by sports fans, recently achieved international recognition during the FIFA World Cup soccer tournament in South Africa. We hypothesised that vuvuzelas might facilitate the generation and dissemination of respiratory aerosols. To investigate the quantity and size of aerosols emitted when the instrument is played, eight healthy volunteers were asked to blow a vuvuzela. For each individual the concentration of particles in expelled air was measured using a six channel laser particle counter and the duration of blowing and velocity of air leaving the vuvuzela were recorded. To allow comparison with other activities undertaken at sports events each individual was also asked to shout and the measurements were repeated while using a paper cone to confine the exhaled air. Triplicate measurements were taken for each individual. The mean peak particle counts were 658×103 per litre for the vuvuzela and 3.7×103 per litre for shouting, representing a mean log10 difference of 2.20 (95% CI: 2.03,2.36; p<0.001). The majority (>97%) of particles captured from either the vuvuzela or shouting were between 0.5 and 5 microns in diameter. Mean peak airflows recorded for the vuvuzela and shouting were 6.1 and 1.8 litres per second respectively. We conclude that plastic blowing horns (vuvuzelas) have the capacity to propel extremely large numbers of aerosols into the atmosphere of a size able to penetrate the lower lung. Some respiratory pathogens are spread via contaminated aerosols emitted by infected persons. Further investigation is required to assess the potential of the vuvuzela to contribute to the transmission of aerosol borne diseases. We recommend, as a precautionary measure, that people with respiratory infections should be advised not to blow their vuvuzela in enclosed spaces and where there is a risk of infecting others. PMID:21629778

The prevalence of undiagnosed concussions in athletes.

PubMed

Meehan, William P; Mannix, Rebekah C; O'Brien, Michael J; Collins, Michael W

2013-09-01

Previous studies suggest athletes underreport concussions. We sought to determine whether athletes in our clinics have sustained previous concussions that went undiagnosed. Multicentered cross sectional study. Two sport concussion clinics. Patients diagnosed with sport-related concussions or concussions with injury mechanisms and forces similar to those observed in sports were included. The proportion of patients who answered "yes" to the following question were defined as having a previously undiagnosed concussion: "Have you ever sustained a blow to the head which was NOT diagnosed as a concussion but was followed by one or more of the signs and symptoms listed in the Post Concussion Symptom Scale?" Of the 486 patients included in the final analysis, 148 (30.5%) patients reported a previously undiagnosed concussion. Athletes reporting previously undiagnosed concussions had a higher mean Post Concussion Symptom Scale (PCSS) score (33 vs 25; P < 0.004) and were more likely to have lost consciousness (31% vs 22%; P = 0.038) with their current injury than athletes without previously undiagnosed concussions. Nearly one-third of athletes have sustained previously undiagnosed concussions, defined as a blow to the head followed by the signs and symptoms included in the PCSS. Furthermore, these previously undiagnosed concussions are associated with higher PCSS scores and higher loss of consciousness rates when future concussions occur. Many athletes have sustained previous blows to the head that result in the signs and symptoms of concussion but have not been diagnosed with a concussion. These injuries are associated with increased rates of loss of consciousness and higher symptom scale scores with future concussions.

Blow-up solutions for L 2 supercritical gKdV equations with exactly k blow-up points

NASA Astrophysics Data System (ADS)

Lan, Yang

2017-08-01

In this paper we consider the slightly L 2-supercritical gKdV equations \\partialt u+(uxx+u\\vert u\\vert p-1)_x=0 , with the nonlinearity 5 and 0<\\varepsilon\\ll 1 . In the previous work of the author, we know that there exists a stable self-similar blow-up dynamics for slightly L 2-supercritical gKdV equations. Such solutions can be viewed as solutions with a single blow-up point. In this paper we will prove the existence of solutions with multiple blow-up points, and give a description of the formation of the singularity near the blow-up time.

Blow-up for a three dimensional Keller-Segel model with consumption of chemoattractant

NASA Astrophysics Data System (ADS)

Jiang, Jie; Wu, Hao; Zheng, Songmu

2018-04-01

We investigate blow-up properties for the initial-boundary value problem of a Keller-Segel model with consumption of chemoattractant when the spatial dimension is three. Through a kinetic reformulation of the Keller-Segel system, we first derive some higher-order estimates and obtain certain blow-up criteria for the local classical solutions. These blow-up criteria generalize the results in [4,5] from the whole space R3 to the case of bounded smooth domain Ω ⊂R3. Lower global blow-up estimate on ‖ n ‖ L∞ (Ω) is also obtained based on our higher-order estimates. Moreover, we prove local non-degeneracy for blow-up points.

Application of ``POLIS'' PIV system for measurement of velocity fields in a supersonic flow of the wind tunnels

NASA Astrophysics Data System (ADS)

Akhmetbekov, Y. K.; Bilsky, A. V.; Markovich, D. M.; Maslov, A. A.; Polivanov, P. A.; Tsyryul'Nikov, I. S.; Yaroslavtsev, M. I.

2009-09-01

Measurement results on the mean velocity fields and fields of velocity pulsations in the supersonic flows obtained by means of the PIV measurement set “POLIS” are presented. Experiments were carried out in the supersonic blow-down and stationary wind tunnels at the Mach numbers of 4.85 and 6. The method of flow velocity estimate in the test section of the blow-down wind tunnel was grounded by direct measurements of stagnation pressure in the setup settling chamber. The size of tracer particles introduced into the supersonic flow by a mist generator was determined; data on the structure of pulsating velocity in a track of an oblique-cut gas-dynamic whistle were obtained under the conditions of self-oscillations.

An experimental study of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack

NASA Technical Reports Server (NTRS)

Gittner, Nathan M.; Chokani, Ndaona

1991-01-01

An experimental study of the effects of aft blowing on the forebody vortex asymmetry over a 3.0 caliber tangent ogive body at high angles of attack was conducted. The tip of the ogive body was equipped with a single blowing nozzle whose position could be adjusted. The tests were conducted in a subsonic wind tunnel at laminar flow conditions. The effects of model roll, angle of attack, blowing coefficient, and blowing nozzle axial position were independently studied. Surface pressure measurements and flow visualization results were obtained. Aft blowing was observed to alleviate the degree of vortex asymmetry at all angles of attack. The blowing was found to be more effective at the higher angles of attack. However, proportional control of the degree of vortex asymmetry was not observed, because the initial flowfield was highly asymmetric.

Video analysis of head blows leading to concussion in competition Taekwondo.

PubMed

Koh, Jae O; Watkinson, E Jane; Yoon, Yong-Jin

2004-12-01

To analyse the situational and contextual factors surrounding concussions and head blows in Taekwondo. Prospective design. Direct observation, subject interview and videotape recording used. A total of 2328 competitors participated in the 2001 tournament, South Korea. All matches were recorded on videotape. All recipients of head blows were interviewed by athletic therapists and the researcher immediately after the match. The videotapes of concussions and head blows were analysed. A total of 1009 head blows including concussions were analysed. Head blows and concussions were most evident when the attacker was situated in a closed stance and received a single roundhouse kick. The most frequent anatomical site of the head impact was the temporal region. The frequency of head blows and concussions is high in Taekwondo. Development of blocking skills, safety education, rigorous enforcement of the competition rules and improvement of head-gear are recommended.

An electrostatic charge measurement of blowing snow particles focusing on collision frequency to the snow surface

NASA Astrophysics Data System (ADS)

Omiya, S.; Sato, A.

2010-12-01

Blowing snow particles are known to have an electrostatic charge. This charge may be a contributing factor in the formation of snow drifts and snow cornices and changing of the trajectory of blowing snow particles. These formations and phenomena can cause natural disaster such as an avalanche and a visibility deterioration, and obstruct transportation during winter season. Therefore, charging phenomenon of the blowing snow particles is an important issue in terms of not only precise understanding of the particle motion but disaster prevention. The primary factor of charge accumulation to the blowing snow particles is thought to be due to “saltation” of them. The “saltation” is one of movement forms of blowing snow: when the snow particles are transported by the wind, they repeat frictional collisions with the snow surface. In previous studies, charge-to-mass ratios measured in the field were approximately -50 to -10 μC/kg, and in the wind tunnel were approximately -0.8 to -0.1 μC/kg. While there were qualitatively consistent in sign, negative, there were huge gaps quantitatively between them. One reason of those gaps is speculated to be due to differences in fetch. In other words, the difference of the collision frequency of snow particles to the snow surface has caused the gaps. But it is merely a suggestion and that has not been confirmed. The purpose of this experiment is to measure the charge of blowing snow particles focusing on the collision frequency and clarify the relationship between them. Experiments were carried out in the cryogenic wind tunnel of Snow and Ice Research Center (NIED, JAPAN). A Faraday cage and an electrometer were used to measure the charge of snow particles. These experiments were conducted over the hard snow surface condition to prevent the erosion of the snow surface and the generation of new snow particles from the surface. The collision frequency of particle was controlled by changing the wind velocity (4.5 to 7 m/s) under the fixed fetch (12m). The number of collisions of particle was converted from the wind velocity using an equation obtained by Kosugi et al. (2004). Blowing snow particles tend to accumulate negative charges gradually with increase of the number of collisions to the snow surface. As a result, it is demonstrated that the gaps between the field values and the wind tunnel ones were due to difference of the collision frequency of snow particles. Assuming a logarithmic relationship as first approximation between the measured charges and the number of collisions, the charge-to-mass ratios will reach roughly the same value which was obtained in the field with several hundreds collisions. For instance, fetch is needed roughly 200m for blowing snow particles to gain -30 μC/kg under the following conditions: air temperature -20 degrees Celsius, wind velocity 7m/s and hard snow surface. REFERENCE: Kosugi et al., (2004): Dependence of drifting snow saltation length on snow surface hardness. Cold Reg. Sci. Technol., 39, 133-139.

New Perspectives on Blowing Snow Transport, Sublimation, and Layer Thermodynamic Structure over Antarctica

NASA Technical Reports Server (NTRS)

Palm, Steve; Kayetha, Vinay; Yang, Yuekui; Pauly, Rebecca M.

2017-01-01

Blowing snow over Antarctica is a widespread and frequent event. Satellite remote sensing using lidar has shown that blowing snow occurs over 70% of the time over large areas of Antarctica in winter. The transport and sublimation of blowing snow are important terms in the ice sheet mass balance equation and the latter is also an important part of the hydrological cycle. Until now the only way to estimate the magnitude of these processes was through model parameterization. We present a technique that uses direct satellite observations of blowing snow and model (MERRA-2) temperature and humidity fields to compute both transport and sublimation of blowing snow over Antarctica for the period 2006 to 2016. The results show a larger annual continent-wide integrated sublimation than current published estimates and a significant transport of snow from continent to ocean. The talk will also include the lidar backscatter structure of blowing snow layers that often reach heights of 200 to 300 m as well as the first dropsonde measurements of temperature, moisture and wind through blowing snow layers.

Full-Scale Wind-Tunnel Investigation of a Jet Flap in Conjunction with a Plain Flap with Blowing Boundary-Layer Control on a 35 deg Sweptback-Wing Airplane

NASA Technical Reports Server (NTRS)

Aoyagi, Kiyoshi; Hickey, David H.

1959-01-01

Previous investigations have shown that increased blowing at the hinge-line radius of a plain flap will give flap lift increases above that realized with boundary-layer control. Other experiments and theory have shown that blowing from a wing trailing edge, through the jet flap effect, produced lift increases. The present investigation was made to determine whether blowing simultaneously at the hinge-line radius and trailing edge would be more effective than blowing separately at either location. The tests were made at a Reynolds number of 4.5 x 10(exp 6) with a 35 deg sweptback-wing airplane. For this report, only the lift data are presented. Of the three flap blowing arrangements tested, blowing distributed between the trailing edge and the hinge-line radius of a plain flap was found to be superior to blowing at either location separately at the plain flap deflections of interest. Comparison of estimated and experimental jet flap effectiveness was fair.

A review on adverse event profiles of epidermal growth factor receptor-tyrosine kinase inhibitors in nonsmall cell lung cancer patients.

PubMed

Biswas, B; Ghadyalpatil, N; Krishna, M V; Deshmukh, J

2017-12-01

The epidermal growth factor receptor (EGFR)-tyrosine kinase inhibitors (TKIs) have revolutionized the treatment of EGFR-mutant nonsmall cell lung cancer (NSCLC). These EGFR TKIs demonstrate a different adverse event (AE) profile as compared to conventional chemotherapy agents. They are more commonly associated with cutaneous AEs and diarrhea while hematological AEs occurred commonly with chemotherapy agents. These AEs are the extension of pharmacological effect and occur as a result of blockade of EGFR-regulated pathways in the skin and gastrointestinal tract. This review article sheds light on the safety profile of first-, second-, and third-generation EGFR TKIs based on data obtained from several clinical trials conducted in NSCLC patients and highlights trials comparing these agents with the conventional chemotherapy agents. The strategies to manage EGFR TKI-related AEs are also reviewed.

Controlled vortical flow on delta wings through unsteady leading edge blowing

NASA Technical Reports Server (NTRS)

Lee, K. T.; Roberts, Leonard

1990-01-01

The vortical flow over a delta wing contributes an important part of the lift - the so called nonlinear lift. Controlling this vortical flow with its favorable influence would enhance aircraft maneuverability at high angle of attack. Several previous studies have shown that control of the vortical flow field is possible through the use of blowing jets. The present experimental research studies vortical flow control by applying a new blowing scheme to the rounded leading edge of a delta wing; this blowing scheme is called Tangential Leading Edge Blowing (TLEB). Vortical flow response both to steady blowing and to unsteady blowing is investigated. It is found that TLEB can redevelop stable, strong vortices even in the post-stall angle of attack regime. Analysis of the steady data shows that the effect of leading edge blowing can be interpreted as an effective change in angle of attack. The examination of the fundamental time scales for vortical flow re-organization after the application of blowing for different initial states of the flow field is studied. Different time scales for flow re-organization are shown to depend upon the effective angle of attack. A faster response time can be achieved at angles of attack beyond stall by a suitable choice of the initial blowing momentum strength. Consequently, TLEB shows the potential of controlling the vortical flow over a wide range of angles of attack; i.e., in both for pre-stall and post-stall conditions.

[Gemcitabine and non small-cell lung cancer].

PubMed

Vignot, Stéphane; Besse, Benjamin

2007-01-01

Questions raised during gemcitabine development reflect non small-cell lung cancer (NSCLC) history during last 10 years. Third generation therapies (gemcitabine, vinorelbine and taxanes) combined with platinium compounds are now to be prescribed in almost all clinical situations, from surgically removed tumors to metastatic diseases. The 30% response rate usually reported in advanced disease (with a median survival of 10 months) has to be improved and a more global approach is nowadays mandatory, including targeted agents. This review sum-up the clinical situations in which gemcitabine can be prescribed (advanced disease), or shall be prescribed (adjuvant setting, combination with anti-angiogenic agent or EGFR inhibitors), and highlight opening questions.

Use of a rapid brain-sampling technique in a physiologic preparation: effects of morphine, ketamine, and halothane on tissue energy intermediates.

PubMed

Dedrick, D F; Sherer, Y D; Biebuyck, J F

1975-06-01

A new method of rapid sampling of brain tissue, "freeze-blowing," has been used to compare the neurochemistry of the brain during anesthesia with that in the awake state. The method avoids anoxia associated with the sampling process. Physiologic variables, including body temperature, blood-gas tensions and blood pressure, were carefully monitored and controlled in the experimental animals. None of the agents tested (halothane, morphine, and ketamine) reduced the brain tissue high-energy phosphate reserved. All three drugs doubled glucose levels. Morphine lowered both lactate and the lactate/pyruvate ratio. Uniformly, the three anesthetic agents led to twofold increases of brain cyclic 3'-5' adenosine monophosphate concentrations. These changes suggest a possible role for cyclic nucleotides in central neurotransmission.

Testosterone and progesterone concentrations in blow samples are biologically relevant in belugas (Delphinapterus leucas).

PubMed

Richard, Justin T; Robeck, Todd R; Osborn, Steven D; Naples, Lisa; McDermott, Alexa; LaForge, Robert; Romano, Tracy A; Sartini, Becky L

2017-05-15

Steroid hormone analysis in blow (respiratory vapor) may provide a minimally invasive way to assess the reproductive status of wild cetaceans. Biological validation of the method is needed to allow for the interpretation of hormone measurements in blow samples. Utilizing samples collected from trained belugas (Delphinapterus leucas, n=20), enzyme immunoassays for testosterone and progesterone were validated for use with beluga blow samples. Testosterone concentrations in 40 matched blood and blow samples collected from 4 male belugas demonstrated a positive correlation (R 2 =0.52, p<0.0001). Progesterone concentrations in 64 matching blood and blow samples from 11 females were also positively correlated (R 2 =0.60, p<0.0001). Testosterone concentrations (mean±SD) in blow samples collected from adult males (119.3±14.2pg/ml) were higher (p<0.01) than that of a juvenile male (<8years) (59.4±6.5pg/ml) or female belugas (54.1±25.7pg/ml). Among adult males, testosterone concentrations in blow demonstrated a seasonal pattern of secretion, with peak secretion occurring during the breeding season (February-April, 136.95±33.8pg/ml). Progesterone concentrations in blow varied by reproductive status; pregnant females (410.6±87.8pg/ml) and females in the luteal phase of the estrous cycle (339.5±51.0pg/ml) had higher (p<0.0001) blow progesterone concentrations than non-pregnant females without a corpus luteum (242.5±27.3pg/ml). Results indicate that blow sample analysis can be used to detect variation in reproductive states associated with large differences in circulating testosterone or progesterone in belugas. Copyright © 2016 Elsevier Inc. All rights reserved.

Isolation of NDM-1-producing multidrug-resistant Pseudomonas putida from a paediatric case of acute gastroenteritis, India.

PubMed

Bhattacharya, D; Dey, S; Kadam, S; Kalal, S; Jali, S; Koley, H; Sinha, R; Nag, D; Kholkute, S D; Roy, S

2015-05-01

Pseudomonas putida is an uncommon opportunistic pathogen, usually susceptible to antimicrobial agents. Data concerning resistance to antimicrobial agents in clinical P. putida isolates are limited. To the best of our knowledge we report for the first time the isolation of NDM-1-producing multidrug-resistant P. putida from a case of acute gastroenteritis. The isolate showed resistance to a wide range of antimicrobials, including fluoroquinolones, third-generation cephalosporins and carbapenems. The isolate also exhibited multiple mutations in the quinolone resistance determining region and showed the presence of qepA, bla TEM , bla OXA1 and bla OXA7 genes. The present study highlights the importance of looking for the relatively rare aetiological agents in clinical samples that do not yield common pathogens.

Isolation of NDM-1-producing multidrug-resistant Pseudomonas putida from a paediatric case of acute gastroenteritis, India

PubMed Central

Bhattacharya, D.; Dey, S.; Kadam, S.; Kalal, S.; Jali, S.; Koley, H.; Sinha, R.; Nag, D.; Kholkute, S.D.; Roy, S.

2015-01-01

Pseudomonas putida is an uncommon opportunistic pathogen, usually susceptible to antimicrobial agents. Data concerning resistance to antimicrobial agents in clinical P. putida isolates are limited. To the best of our knowledge we report for the first time the isolation of NDM-1-producing multidrug-resistant P. putida from a case of acute gastroenteritis. The isolate showed resistance to a wide range of antimicrobials, including fluoroquinolones, third-generation cephalosporins and carbapenems. The isolate also exhibited multiple mutations in the quinolone resistance determining region and showed the presence of qepA, blaTEM, blaOXA1 and blaOXA7 genes. The present study highlights the importance of looking for the relatively rare aetiological agents in clinical samples that do not yield common pathogens. PMID:25893095

Whistle-Blowing and the Code of Silence in Police Agencies: Policy and Structural Predictors

ERIC Educational Resources Information Center

Rothwell, Gary R.; Baldwin, J. Norman

2007-01-01

This article reports the findings from a study that investigates predictors of police willingness to blow the whistle and police frequency of blowing the whistle on seven forms of misconduct. It specifically investigates the capacity of nine policy and structural variables to predict whistle-blowing. The results indicate that two variables, a…

Reducing secondary losses by blowing cold air in a turbine

NASA Technical Reports Server (NTRS)

Koschel, W.

1977-01-01

Local blowing on the profile suction side of the turbine guide wheel blades can be effective in preventing the propagation of secondary flows that is, the transport of casing and hub boundary layers by pressure gradients. Some preliminary results on how the blowing should be accomplished in order to influence the secondary flows in the desired manner are given. The effectiveness of blowing is demonstrated. Blowing is also seen to be more effective than using boundary layer slots as far as diminishing losses in the rim zones is concerned.

Experimental investigation of tangential blowing for control of the strong shock boundary layer interaction on inlet ramps

NASA Technical Reports Server (NTRS)

Schwendemann, M. F.

1981-01-01

A 0.165-scale isolated inlet model was tested in the NASA Lewis Research Center 8-ft by 6-ft Supersonic Wind Tunnel. Ramp boundary layer control was provided by tangential blowing from a row of holes in an aft-facing step set into the ramp surface. Testing was performed at Mach numbers from 1.36 to 1.96 using both cold and heated air in the blowing system. Stable inlet flow was achieved at all Mach numbers. Blowing hole geometry was found to be significant at 1.96M. Blowing air temperature was found to have only a small effect on system performance. High blowing levels were required at the most severe test conditions.

Tangential blowing for control of strong normal shock - Boundary layer interactions on inlet ramps

NASA Technical Reports Server (NTRS)

Schwendemann, M. F.; Sanders, B. W.

1982-01-01

The use of tangential blowing from a row of holes in an aft facing step is found to provide good control of the ramp boundary layer, normal shock interaction on a fixed geometry inlet over a wide range of inlet mass flow ratios. Ramp Mach numbers of 1.36 and 1.96 are investigated. The blowing geometry is found to have a significant effect on system performance at the highest Mach number. The use of high-temperature air in the blowing system, however, has only a slight effect on performance. The required blowing rates are significantly high for the most severe test conditions. In addition, the required blowing coefficient is found to be proportional to the normal shock pressure rise.

Use of cooling tower blow down in ethanol fermentation.

PubMed

Rajagopalan, N; Singh, V; Panno, B; Wilcoxon, M

2010-01-01

Reducing water consumption in bioethanol production conserves an increasingly scarce natural resource, lowers production costs, and minimizes effluent management issues. The suitability of cooling tower blow down water for reuse in fermentation was investigated as a means to lower water consumption. Extensive chemical characterization of the blow down water revealed low concentrations of toxic elements and total dissolved solids. Fermentation carried out with cooling tower blow down water resulted in similar levels of ethanol and residual glucose as a control study using deionized water. The study noted good tolerance by yeast to the specific scale and corrosion inhibitors found in the cooling tower blow down water. This research indicates that, under appropriate conditions, reuse of blow down water from cooling towers in fermentation is feasible.

Production and Compressive Characterization of Aluminium MMC Foam Manufactured Using Dual Foaming Agent

NASA Astrophysics Data System (ADS)

Haidar, S.; Ansary, S.; Rahman, A.

2016-02-01

Aluminium foams, produced by melting Aluminium alloy (LM6) containing blowing agent(s) and vigorous stirring. TiH2 is a known agent for this. As TiH2 begins to decompose into Ti and gaseous H2 when heated above about 465°C, large volumes of hydrogen gas are rapidly produced, creating bubbles that leads to a closed cell foam. A novel Strategy to enhance the mechanical properties of Al-MMC foams is discussed here, and it is demonstrated that titanium hydride (TiH2) in the form of 10-15 μm diameter particles can be pre-treated by selective oxidation to produce more uniform foams having better compressive properties (yield strength and energy absorption). It is found that the mechanical properties of the foams and the uniformity of cell size distribution is improved when the foam is blown with an optimized mixture of CaCO3 and pretreated TiH2. In order to define the relationship of mechanical properties with relative density of this material, correlations which uniquely defines the compressive behaviour of this modified Al- MMC foam has been developed.

Implications of current recommendations for third-generation cephalosporin use in the WHO Western Pacific Region following the emergence of multiresistant gonococci.

PubMed

Tapsall, J W

2009-08-01

To ascertain recommendations for the treatment of gonorrhoea in the WHO Western Pacific Region (WPR) following the emergence of "cephalosporin-resistant" Neisseria gonorrhoeae and to relate these to clinical and laboratory measures directed towards disease and antibiotic resistance control. WHO WPR Gonococcal Antimicrobial Resistance Programme members provided data on the type, dose and source of third-generation cephalosporins recommended for the treatment of gonorrhoea. Ceftriaxone was recommended more widely (11/15 respondents) than cefixime (five centres). No cephalosporins were recommended in three jurisdictions. One other oral (ceftibuten) and injectable (cefodizime) agent was recommended. Uniform (400 mg) doses of cefixime were recommended but ceftriaxone regimens ranged between 125 mg and 1 g, with nine of 11 respondents using a 250 mg dose. Both generic and proprietary preparations were widely used. Third-generation cephalosporins are widely recommended for the treatment of gonorrhoea in the WPR, with injectable ceftriaxone more extensively so than oral cefixime and in an expanded dose range. Few other cephalosporins were recommended. Current knowledge suggests that the trend towards ceftriaxone treatment in higher doses may decrease the impact of the circulation of "cephalosporin-resistant" gonococci in the WPR. These recommendations represent public sector practice only and of themselves are unlikely to contain the further spread of "cephalosporin-resistant" gonococci because of the general clinical use of cephalosporins. Optimisation of strategies for laboratory detection of third-generation cephalosporin resistance can be simplified in the WPR because of the restricted spectrum of cephalosporins recommended. Additional efforts are urgently required for both disease and antibiotic resistance control in gonorrhoea.

Winds of Change Blowing for Wind Farm Research with NREL's SOWFA Tool |

Science.gov Websites

News | NREL Winds of Change Blowing for Wind Farm Research with NREL's SOWFA Tool Winds of Change Blowing for Wind Farm Research with NREL's SOWFA Tool April 1, 2016 Before the Energy Department's that researchers all over the world could embrace. Now, the winds of change are blowing. SOWFA is a

Control of VR-7 Dynamic Stall by Strong Steady Blowing

NASA Technical Reports Server (NTRS)

Weaver, D.; McAlister, K. W.; Tso, J.

2004-01-01

An experiment was performed in a water tunnel on a Boeing-Vertol VR-7 airfoil to study the effects of tangential blowing over the upper surface. Blowing was applied at the quarter-chord location during sinusoidal pitching oscillations described by alpha = alpha(sub m) + 10 deg sin omega t. Results were obtained for a Reynolds number of 1 x 10(exp 5), mean angles of 10 and 15 deg, reduced frequencies ranging from 0.005 to 0.15, and blowing rates from C(sub mu) = 0.16 to 0.66. Unsteady lift, drag, and pitching moment loads are reported, along with fluorescent-dye flow visualizations. Strong steady blowing was found to prevent the bursting of the leading-edge separation bubble at several test points. When this occurred, the lift was increased significantly, stall was averted, and the shape of the moment response showed a positive damping in pitch. In almost all cases, steady blowing reduced the hysteresis amplitudes present in the loads, but the benefits diminished as the reduced frequency and mean angle of oscillation increased. A limited number of pulsed blowing cases indicated that for low blowing rates, the greatest gains were achieved at F(sup +) = 0.9.

Low-Speed Wind-Tunnel Investigation of Blowing Boundary-Layer Control on Leading- and Trailing-Edge Flaps of a Large-Scale, Low-Aspect-Ratio, 45 Swept-wing Airplane Configuration

NASA Technical Reports Server (NTRS)

Maki, Ralph L.

1959-01-01

Blowing boundary-layer control was applied to the leading- and trailing-edge flaps of a 45 deg sweptback-wing complete model in a full-scale low-speed wind-tunnel study. The principal purpose of the study was to determine the effects of leading-edge flap deflection and boundary-layer control on maximum lift and longitudinal stability. Leading-edge flap deflection alone was sufficient to maintain static longitudinal stability without trailing-edge flaps. However, leading-edge flap blowing was required to maintain longitudinal stability by delaying leading-edge flow separation when trailing-edge flaps were deflected either with or without blowing. Partial-span leading-edge flaps deflected 60 deg with moderate blowing gave the major increase in maximum lift, although higher deflection and additional blowing gave some further increase. Inboard of 0.4 semispan leading-edge flap deflection could be reduced to 40 deg and/or blowing could be omitted with only small loss in maximum lift. Trailing-edge flap lift increments were increased by boundary-layer control for deflections greater than 45 deg. Maximum lift was not increased with deflected trailing-edge flaps with blowing.

Augmentation of maneuver performance by spanwise blowing

NASA Technical Reports Server (NTRS)

Erickson, G. E.; Campbell, J. F.

1977-01-01

A generalized wind tunnel model was tested to investigate new component concepts utilizing spanwise blowing to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on high angle of attack performance, stability, and control at subsonic speeds. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex-induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack. Spanwise blowing on the wing reduced horizontal tail loading and improved the lateral-directional stability characteristics of a wing-horizontal tail-vertical tail configuration.

Extremely low order time-fractional differential equation and application in combustion process

NASA Astrophysics Data System (ADS)

Xu, Qinwu; Xu, Yufeng

2018-11-01

Fractional blow-up model, especially which is of very low order of fractional derivative, plays a significant role in combustion process. The order of time-fractional derivative in diffusion model essentially distinguishes the super-diffusion and sub-diffusion processes when it is relatively high or low accordingly. In this paper, the blow-up phenomenon and condition of its appearance are theoretically proved. The blow-up moment is estimated by using differential inequalities. To numerically study the behavior around blow-up point, a mixed numerical method based on adaptive finite difference on temporal direction and highly effective discontinuous Galerkin method on spatial direction is proposed. The time of blow-up is calculated accurately. In simulation, we analyze the dynamics of fractional blow-up model under different orders of fractional derivative. It is found that the lower the order, the earlier the blow-up comes, by fixing the other parameters in the model. Our results confirm the physical truth that a combustor for explosion cannot be too small.

First Satellite-detected Perturbations of Outgoing Longwave Radiation Associated with Blowing Snow Events over Antarctica

NASA Technical Reports Server (NTRS)

Yang, Yuekui; Palm, Stephen P.; Marshak, Alexander; Wu, Dong L.; Yu, Hongbin; Fu, Qiang

2014-01-01

We present the first satellite-detected perturbations of the outgoing longwave radiation (OLR) associated with blowing snow events over the Antarctic ice sheet using data from Cloud-Aerosol Lidar with Orthogonal Polarization and Clouds and the Earth's Radiant Energy System. Significant cloud-free OLR differences are observed between the clear and blowing snow sky, with the sign andmagnitude depending on season and time of the day. During nighttime, OLRs are usually larger when blowing snow is present; the average difference in OLRs between without and with blowing snow over the East Antarctic Ice Sheet is about 5.2 W/m2 for the winter months of 2009. During daytime, in contrast, the OLR perturbation is usually smaller or even has the opposite sign. The observed seasonal variations and day-night differences in the OLR perturbation are consistent with theoretical calculations of the influence of blowing snow on OLR. Detailed atmospheric profiles are needed to quantify the radiative effect of blowing snow from the satellite observations.

The Effects of Sweeping Jet Actuator Parameters on Flow Separation Control

NASA Technical Reports Server (NTRS)

Koklu, Mehti

2015-01-01

A parametric experimental study was performed with sweeping jet actuators (fluidic oscillators) to determine their effectiveness in controlling flow separation on an adverse pressure gradient ramp. Actuator parameters that were investigated include blowing coefficients, operation mode, pitch and spreading angles, streamwise location, aspect ratio, and scale. Surface pressure measurements and surface oil flow visualization were used to characterize the effects of these parameters on the actuator performance. 2D Particle Image Velocimetry measurements of the flow field over the ramp and hot-wire measurements of the actuator's jet flow were also obtained for selective cases. In addition, the sweeping jet actuators were compared to other well-known flow control techniques such as micro-vortex generators, steady blowing, and steady vortex-generating jets. The results confirm that the sweeping jet actuators are more effective than steady blowing and steady vortex-generating jets. The results also suggest that an actuator with a larger spreading angle placed closer to the location where the flow separates provides better performance. For the cases tested, an actuator with an aspect ratio, which is the width/depth of the actuator throat, of 2 was found to be optimal. For a fixed momentum coefficient, decreasing the aspect ratio to 1 produced weaker vortices while increasing the aspect ratio to 4 reduced coverage area. Although scaling down the actuator (based on the throat dimensions) from 0.25 inch x 0.125 inch to 0.15 inch x 0.075 inch resulted in similar flow control performance, scaling down the actuator further to 0.075 inch x 0.0375 inch reduced the actuator efficiency by reducing the coverage area and the amount of mixing in the near-wall region. The results of this study provide insight that can be used to design and select the optimal sweeping jet actuator configuration for flow control applications.

Single-stage evaluation of highly-loaded high-Mach-number compressor stages 5. Data and performance of baseline, corner-blow wall suction and combined corner blow wall suction stator

NASA Technical Reports Server (NTRS)

Nikkanen, J. P.; Brooky, J. P.

1972-01-01

A single-stage compressor with a rotor tip speed of 1600 ft/sec and a 0.5 hub tip ratio was used to investigate the effects of several stator endwall treatment methods on stage range and performance. These endwall treatment methods consisted of stator corner-blow, annular wall suction upstream of stator leading edge, and combined corner-blow and annular wall suction. The overall stage performance with corner blow was essentially the same as the baseline performance. The performance for the annular wall suction and the combined corner-blow and wall suction showed a reduction in peak efficiency of 2.5 percentage points compared to the baseline data.

Cell Death Pathways and Phthalocyanine as an Efficient Agent for Photodynamic Cancer Therapy

PubMed Central

Mfouo-Tynga, Ivan; Abrahamse, Heidi

2015-01-01

The mechanisms of cell death can be predetermined (programmed) or not and categorized into apoptotic, autophagic and necrotic pathways. The process of Hayflick limits completes the execution of death-related mechanisms. Reactive oxygen species (ROS) are associated with oxidative stress and subsequent cytodamage by oxidizing and degrading cell components. ROS are also involved in immune responses, where they stabilize and activate both hypoxia-inducible factors and phagocytic effectors. ROS production and presence enhance cytodamage and photodynamic-induced cell death. Photodynamic cancer therapy (PDT) uses non-toxic chemotherapeutic agents, photosensitizer (PS), to initiate a light-dependent and ROS-related cell death. Phthalocyanines (PCs) are third generation and stable PSs with improved photochemical abilities. They are effective inducers of cell death in various neoplastic models. The metallated PCs localize in critical cellular organelles and are better inducers of cell death than other previous generation PSs as they favor mainly apoptotic cell death events. PMID:25955645

The evolution of recombinant thrombolytics: Current status and future directions

PubMed Central

Adivitiya; Khasa, Yogender Pal

2017-01-01

ABSTRACT Cardiovascular disorders are on the rise worldwide due to alcohol abuse, obesity, hypertension, raised blood lipids, diabetes and age-related risks. The use of classical antiplatelet and anticoagulant therapies combined with surgical intervention helped to clear blood clots during the inceptive years. However, the discovery of streptokinase and urokinase ushered the way of using these enzymes as thrombolytic agents to degrade the fibrin network with an issue of systemic hemorrhage. The development of second generation plasminogen activators like anistreplase and tissue plasminogen activator partially controlled this problem. The third generation molecules, majorly t-PA variants, showed desirable properties of improved stability, safety and efficacy with enhanced fibrin specificity. Plasmin variants are produced as direct fibrinolytic agents as a futuristic approach with targeted delivery of these drugs using liposome technlogy. The novel molecules from microbial, plant and animal origin present the future of direct thrombolytics due to their safety and ease of administration. PMID:27696935

Osimertinib: A Novel Dermatologic Adverse Event Profile in Patients with Lung Cancer.

PubMed

Chu, Chia-Yu; Choi, Jennifer; Eaby-Sandy, Beth; Langer, Corey J; Lacouture, Mario E

2018-04-12

Dermatologic adverse events (dAEs) are common with the use of epidermal growth factor receptor-tyrosine kinase inhibitor (EGFR-TKI) therapy. First- and second-generation agents (erlotinib, gefitinib, and afatinib) are frequently associated with acneiform rash, pruritus, xerosis, and paronychia; the incidence and characterization of these dAEs have been well described. However, there is evidence that the dAE profile is different with third-generation EGFR-TKIs. Herein, we describe the dAEs associated with third-generation EGFR-TKIs and our clinical experience with osimertinib, a third-generation EGFR-TKI approved by the U.S. Food and Drug Administration for the treatment of metastatic, EGFR T790M mutation-positive non-small cell lung cancer in patients whose disease has progressed on or after EGFR-TKI therapy. Case summaries of patients from two of our institutions who received osimertinib and were referred to a dermatologist for dAEs are also presented. Overall, the evidence suggests that osimertinib is associated with less severe and less frequent dAEs than first- and second-generation EGFR-TKIs and that therefore a different approach is warranted. Finally, we outline dAE management approaches for osimertinib in the context of those typically employed with first- and second-generation EGFR-TKIs. Appropriate prevention and management of dermatologic adverse events (dAEs) associated with the use of epidermal growth factor receptor-tyrosine kinase inhibitors (EGFR-TKIs) may help patients to continue therapy and lessen any negative impact on their quality of life. EGFR-TKIs are frequently associated with acneiform rash, pruritus, xerosis, and paronychia; however, dAEs associated with third-generation EGFR-TKIs are lower in frequency and severity. Before therapy, health care providers should discuss the potential osimertinib-associated dAEs and encourage patients to report their dAEs. Patients should also be educated on prophylactic measures to minimize the severity of dAEs and the importance of adherence to the treatment regimen. © AlphaMed Press 2018.

Influence of air-jet vortex generator diameter on separation region

NASA Astrophysics Data System (ADS)

Szwaba, Ryszard

2013-08-01

Control of shock wave and boundary layer interaction continues to attract a lot of attention. In recent decades several methods of interaction control have been investigated. The research has mostly concerned solid (vane type) vortex generators and transpiration methods of suction and blowing. This investigation concerns interaction control using air-jets to generate streamwise vortices. The effectiveness of air-jet vortex generators in controlling separation has been proved in a previous research. The present paper focuses on the influence of the vortex generator diameter on the separation region. It presents the results of experimental investigations and provides new guidelines for the design of air-jet vortex generators to obtain more effective separation control.

What Fraction of Active Galaxies Actually Show Outflows?

NASA Astrophysics Data System (ADS)

Ganguly, Rajib; Brotherton, M. S.

2007-12-01

Outflows from active galactic nuclei (AGNs) seem to be common and are thought to be important from a variety of perspectives: as an agent of chemical enhancement of the interstellar and intergalactic media, as an agent of angular momentum removal from the accreting central engine, and as an agent limiting star formation in starbursting systems by blowing out gas and dust from the host galaxy. To understand these processes, we must determine what fraction of AGNs feature outflows and understand what forms they take. We examine recent surveys of outflows detected in ultraviolet absorption over the entire range of velocities and velocity widths (i.e., broad absorption lines, associated absorption lines, and high-velocity narrow absorption lines). While the fraction of specific forms of outflows depends on AGN properties, the overall fraction displaying outflows is fairly constant, approximately 60%, over many orders of magnitude in luminosity. We discuss implications of this result and ways to refine our understanding of outflows. We acknowledge support from the US National Science Foundation through grant AST 05-07781.

Mesoscale cyclogenesis dynamics over the southwestern Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Carrasco, Jorge F.; Bromwich, David H.

1993-07-01

Previous work has shown that frequent mesoscale cyclogenesis adjacent to Franklin Island is linked to the strong and persistent katabatic winds from East Antarctica which funnel into Terra Nova Bay and then blow out over the southwestern Ross Sea. Four mesoscale cyclones that formed near Terra Nova Bay between February 16 and 20, 1988 are examined to more clearly define the governing mechanisms. These events are investigated using all available observations, including automatic weather station data, high-resolution satellite images, satellite soundings, and hemispheric synoptic analyses. The first two cyclones formed on low-level baroclinic zones established by the synoptic scale advection of warm moist air toward the cold continental air blowing gently from East Antarctica. In the second case, baroclinic instability of this small-scale cold front was apparently triggered by the enhanced upward vertical motion associated with the approach of a midtropospheric trough. The third mesocyclone formed shortly after on a baroclinic zone over the polar plateau; the second vortex completely disrupted the usual katabatic drainage over the plateau and forced warm moist air over the coastal slopes. All three cyclones moved to the north in the prevailing cyclonic flow, but the plateau vortex lasted for only 6 hours. The fourth mesoscale low formed in conjunction with an abrupt and intense surge of katabatic air from Terra Nova Bay which resharpened the coastal baroclinic zone. At the same time a transiting midtropospheric trough probably associated with lower tropospheric upward vertical motion apparently accelerated the katabatic winds and triggered the vortex formation. A similar katabatic wind-forced mesocyclone formed near Byrd Glacier. The two vortices moved to the east-southeast and northeast, respectively, apparently being steered by the generating katabatic airstreams, and merged just to the north of the Ross Ice Shelf. The combined vortex reintensified as another trough passed overhead and moved eastward to West Antarctica where it dissipated two days later.

Blowing Snow Sublimation and Transport over Antarctica from 11 Years of CALIPSO Observations

NASA Technical Reports Server (NTRS)

Palm, Stephen P.; Kayetha, Vinay; Yang, Yuekui; Pauly, Rebecca

2017-01-01

Blowing snow processes commonly occur over the earth's ice sheets when the 10 mile wind speed exceeds a threshold value. These processes play a key role in the sublimation and redistribution of snow thereby influencing the surface mass balance. Prior field studies and modeling results have shown the importance of blowing snow sublimation and transport on the surface mass budget and hydrological cycle of high-latitude regions. For the first time, we present continent-wide estimates of blowing snow sublimation and transport over Antarctica for the period 2006-2016 based on direct observation of blowing snow events. We use an improved version of the blowing snow detection algorithm developed for previous work that uses atmospheric backscatter measurements obtained from the CALIOP (Cloud-Aerosol Lidar with Orthogonal Polarization) lidar aboard the CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation) satellite. The blowing snow events identified by CALIPSO and meteorological fields from MERRA-2 are used to compute the blowing snow sublimation and transport rates. Our results show that maximum sublimation occurs along and slightly inland of the coastline. This is contrary to the observed maximum blowing snow frequency which occurs over the interior. The associated temperature and moisture reanalysis fields likely contribute to the spatial distribution of the maximum sublimation values. However, the spatial pattern of the sublimation rate over Antarctica is consistent with modeling studies and precipitation estimates. Overall, our results show that the 2006-2016 Antarctica average integrated blowing snow sublimation is about 393 +/- 196 Gt yr(exp -1), which is considerably larger than previous model-derived estimates. We find maximum blowing snow transport amount of 5 Mt km-1 yr(exp -1) over parts of East Antarctica and estimate that the average snow transport from continent to ocean is about 3.7 Gt yr(exp -1). These continent-wide estimates are the first of their kind and can be used to help model and constrain the surface mass budget over Antarctica.

Experimental and computational study of the effect of shocks on film cooling effectiveness in scramjet combustors

NASA Technical Reports Server (NTRS)

Kamath, Pradeep S.; Holden, Michael S.; Mcclinton, Charles R.

1990-01-01

This paper presents results from a study conducted to investigate the effect of incident oblique shocks on the effectiveness of a coolant film at Mach numbers, typical of those expected in a scramjet combustor at Mach 15 to 20 flight. Computations with a parabolic code are in good agreement with the measured pressures and heat fluxes, after accounting for the influence of the shock upstream of its point of impingement on the plate, and the expansion from the trailing edge of the shock generator. The test data shows that, for the blowing rates tested, the film is rendered largely ineffective by the shock. Computations show that coolant blowing rates five to ten times those tested are required to protect against shock-induced heating. The implications of the results to scramjet combustor design are discussed.

Blowing Snow Sublimation at a High Altitude Alpine Site and Effects on the Surface Boundary Layer

NASA Astrophysics Data System (ADS)

Vionnet, V.; Guyomarc'h, G.; Sicart, J. E.; Deliot, Y.; Naaim-Bouvet, F.; Bellot, H.; Merzisen, H.

2017-12-01

In alpine terrain, wind-induced snow transport strongly influences the spatial and temporal variability of the snow cover. During their transport, blown snow particles undergo sublimation with an intensity depending on atmospheric conditions (air temperature and humidity). The mass loss due to blowing snow sublimation is a source of uncertainty for the mass balance of the alpine snowpack. Additionally, blowing snow sublimation modifies humidity and temperature in the surface boundary layer. To better quantify these effects in alpine terrain, a dedicated measurement setup has been deployed at the experimental site of Col du Lac Blanc (2720 m a.s.l., French Alps, Cryobs-Clim network) since winter 2015/2016. It consists in three vertical masts measuring the near-surface vertical profiles (0.2-5 m) of wind speed, air temperature and humidity and blowing snow fluxes and size distribution. Observations collected during blowing snow events without concurrent snowfall show only a slight increase in relative humidity (10-20%) and near-surface saturation is never observed. Estimation of blowing snow sublimation rates are then obtained from these measurements. They range between 0 and 5 mmSWE day-1 for blowing snow events without snowfall in agreement with previous studies in different environments (North American prairies, Antarctica). Finally, an estimation of the mass loss due to blowing snow sublimation at our experimental site is proposed for two consecutive winters. Future use of the database collected in this study includes the evaluation of blowing snow models in alpine terrain.

Description of Larval Instars To Fill a Gap in Forensic Entomology: The Larvae of Paralucilia pseudolyrcea (Diptera: Calliphoridae).

PubMed

Da Silva, S M; Vairo, K P; Moura, M O

2018-05-04

A fundamental assumption of forensic entomology for estimating the postmortem interval is that insect species are accurately identified, which depends on diagnostic morphological characters. Larvae of the blow fly Paralucilia pseudolyrcea (Mello, 1969) (Diptera: Calliphoridae) were sampled from four corpses in the state of Paraná, Brazil, but despite the forensic importance of this species, morphological data for the identification of its larval instars are lacking, limiting its usefulness in such cases. Thus, the main goal of this study was to describe the larval instars of P. pseudolyrcea. The material was obtained from a colony established by larvae collected from a corpse of a murder case. Overall, the distribution of spines is a key character for identifying this species in the first, second and third instars. Other characteristics, such as the presence of an accessory oral sclerite, the small cirri, the number of lobes of the anterior spiracle and the morphology of posterior spiracles, separates P. pseudolyrcea from other necrophagous blow flies. The detailed morphological description provided here facilitates the identification of larval instars of P. pseudolyrcea and their differentiation from those of other calliphorid species.

Suppression of Dynamic Stall by Steady and Pulsed Upper-Surface Blowing

NASA Technical Reports Server (NTRS)

Weaver, D.; McAlister, K. W.; Tso, J.

1996-01-01

The Boeing-Vertol VR-7 airfoil was experimentally studied with steady and pulsed upper-surface blowing for sinusoidal pitching oscillations described by alpha = alpha(sub m) + 10 deg sin(omega t). The tests were conducted in the U.S. Army Aeroflightdynamics Directorate's Water Tunnel at NASA Ames Research Center. The experiment was performed at a Reynolds number of 100,000. Pitch oscillations with alpha(sub m) = 10 deg and 15 deg and with reduced frequencies ranging from k = 0.005 to 0.15 were examined. Blowing conditions ranged from C(sub mu) = 0.03 to 0.66 and F(+) = 0 to 3. Unsteady lift, drag, and pitching-moment loads were measured, and fluorescent-dye flow visualizations were obtained. Steady, upper-surface blowing was found to be capable of trapping a separation bubble near the leading edge during a portion of the airfoil's upward rotation. When this occurred, the lift was increased significantly and stall was averted. In all cases, steady blowing reduced the hysteresis amplitudes present in the loads and produced a large thrust force. The benefits of steady blowing diminished as the reduced frequency and mean angle of oscillation increased. Pulsed blowing showed only marginal benefits for the conditions tested. The greatest gains from pulsed blowing were achieved at F(+) = 0.9.

Roll-Yaw control at high angle of attack by forebody tangential blowing

NASA Technical Reports Server (NTRS)

Pedreiro, N.; Rock, S. M.; Celik, Z. Z.; Roberts, L.

1995-01-01

The feasibility of using forebody tangential blowing to control the roll-yaw motion of a wind tunnel model is experimentally demonstrated. An unsteady model of the aerodynamics is developed based on the fundamental physics of the flow. Data from dynamic experiments is used to validate the aerodynamic model. A unique apparatus is designed and built that allows the wind tunnel model two degrees of freedom, roll and yaw. Dynamic experiments conducted at 45 degrees angle of attack reveal the system to be unstable. The natural motion is divergent. The aerodynamic model is incorporated into the equations of motion of the system and used for the design of closed loop control laws that make the system stable. These laws are proven through dynamic experiments in the wind tunnel using blowing as the only actuator. It is shown that asymmetric blowing is a highly non-linear effector that can be linearized by superimposing symmetric blowing. The effects of forebody tangential blowing and roll and yaw angles on the flow structure are determined through flow visualization experiments. The transient response of roll and yaw moments to a step input blowing are determined. Differences on the roll and yaw moment dependence on blowing are explained based on the physics of the phenomena.

Roll-yaw control at high angle of attack by forebody tangential blowing

NASA Technical Reports Server (NTRS)

Pedreiro, N.; Rock, S. M.; Celik, Z. Z.; Roberts, L.

1995-01-01

The feasibility of using forebody tangential blowing to control the roll-yaw motion of a wind tunnel model is experimentally demonstrated. An unsteady model of the aerodynamics is developed based on the fundamental physics of the flow. Data from dynamic experiments is used to validate the aerodynamic model. A unique apparatus is designed and built that allows the wind tunnel model two degrees of freedom, roll and yaw. Dynamic experiments conducted at 45 degrees angle of attack reveal the system to be unstable. The natural motion is divergent. The aerodynamic model is incorporated into the equations of motion of the system and used for the design of closed loop control laws that make the system stable. These laws are proven through dynamic experiments in the wind tunnel using blowing as the only actuator. It is shown that asymmetric blowing is a highly non-linear effector that can be linearized by superimposing symmetric blowing. The effects of forebody tangential blowing and roll and yaw angles on the flow structure are determined through flow visualization experiments. The transient response of roll and yaw moments to a step input blowing are determined. Differences on the roll and yaw moment dependence on blowing are explained based on the physics of the phenomena.

Nonlinear behavior of the tarka flute's distinctive sounds.

PubMed

Gérard, Arnaud; Yapu-Quispe, Luis; Sakuma, Sachiko; Ghezzi, Flavio; Ramírez-Ávila, Gonzalo Marcelo

2016-09-01

The Andean tarka flute generates multiphonic sounds. Using spectral techniques, we verify two distinctive musical behaviors and the nonlinear nature of the tarka. Through nonlinear time series analysis, we determine chaotic and hyperchaotic behavior. Experimentally, we observe that by increasing the blow pressure on different fingerings, peculiar changes from linear to nonlinear patterns are produced, leading ultimately to quenching.

Nonlinear behavior of the tarka flute's distinctive sounds

NASA Astrophysics Data System (ADS)

Gérard, Arnaud; Yapu-Quispe, Luis; Sakuma, Sachiko; Ghezzi, Flavio; Ramírez-Ávila, Gonzalo Marcelo

2016-09-01

The Andean tarka flute generates multiphonic sounds. Using spectral techniques, we verify two distinctive musical behaviors and the nonlinear nature of the tarka. Through nonlinear time series analysis, we determine chaotic and hyperchaotic behavior. Experimentally, we observe that by increasing the blow pressure on different fingerings, peculiar changes from linear to nonlinear patterns are produced, leading ultimately to quenching.

[Why and how should serous otitis media be treated?].

PubMed

François, M; Bonfils, P; Van Haver, K; Narcy, P

1992-10-01

Serous otitis media is an extremely commonplace condition in pediatric patients and tends to resolve spontaneously. Only some forms warrant treatment. Indications for treatment include frequent superinfections, lasting hearing impairment with adverse consequences on socialization, or debilitation of the tympanic membrane carrying a risk for the ear. Tympanostomy tubes are a palliative treatment for serous otitis which restores hearing within a few hours and eliminates unfixated retractions of the tympanic membrane within a few weeks. Tympanostomy tubes may lead to complications including otorrhea and perforation of the tympanic membrane and should therefore be used only in patients with severe otitis media. Etiologic treatment of serous otitis rests on restoration of satisfactory nasal ventilation (education to improve nose-blowing, adenoidectomy), improvement of eustachian tube patency (corticosteroids), and modification of the characteristics of middle ear secretions (mucolytic agents and mucomodifying agents).

Navier-Stokes Computations of a Wing-Flap Model With Blowing Normal to the Flap Surface

NASA Technical Reports Server (NTRS)

Boyd, D. Douglas, Jr.

2005-01-01

A computational study of a generic wing with a half span flap shows the mean flow effects of several blown flap configurations. The effort compares and contrasts the thin-layer, Reynolds averaged, Navier-Stokes solutions of a baseline wing-flap configuration with configurations that have blowing normal to the flap surface through small slits near the flap side edge. Vorticity contours reveal a dual vortex structure at the flap side edge for all cases. The dual vortex merges into a single vortex at approximately the mid-flap chord location. Upper surface blowing reduces the strength of the merged vortex and moves the vortex away from the upper edge. Lower surface blowing thickens the lower shear layer and weakens the merged vortex, but not as much as upper surface blowing. Side surface blowing forces the lower surface vortex farther outboard of the flap edge by effectively increasing the aerodynamic span of the flap. It is seen that there is no global aerodynamic penalty or benefit from the particular blowing configurations examined.

The significance of vertical moisture diffusion on drifting snow sublimation near snow surface

NASA Astrophysics Data System (ADS)

Huang, Ning; Shi, Guanglei

2017-12-01

Sublimation of blowing snow is an important parameter not only for the study of polar ice sheets and glaciers, but also for maintaining the ecology of arid and semi-arid lands. However, sublimation of near-surface blowing snow has often been ignored in previous studies. To study sublimation of near-surface blowing snow, we established a sublimation of blowing snow model containing both a vertical moisture diffusion equation and a heat balance equation. The results showed that although sublimation of near-surface blowing snow was strongly reduced by a negative feedback effect, due to vertical moisture diffusion, the relative humidity near the surface does not reach 100 %. Therefore, the sublimation of near-surface blowing snow does not stop. In addition, the sublimation rate near the surface is 3-4 orders of magnitude higher than that at 10 m above the surface and the mass of snow sublimation near the surface accounts for more than half of the total snow sublimation when the friction wind velocity is less than about 0.55 m s-1. Therefore, the sublimation of near-surface blowing snow should not be neglected.

The performance of ethics course for increasing students intention to blow the whistle using information technology

NASA Astrophysics Data System (ADS)

Munandar, Agus

2017-10-01

The profession of accounting believes that ethics is very important in the workplace. For that, profession recommends that ethics course should be taught for accounting student. Unfornutaly, the impact of ethics courses on accounting students intention to blow the whistle on organizational wrongdoing using information technology have not been determined. For that, this paper attempts to measure the impact of ethics courses on accounting student intention to blow the whistle on organizational wrongdoing. The research using experimental design for investigate the impact of ethic course on students intention to blow the whistle using IT. The respondents for this study are 40 accountig students. The respondent were given the ethical scenarios and were measured their intention to blow the whistle using information technology. This result of study reports that 70% of accounting student who completed ethic course indicated high intention to blow the whistle on organizational wrongdoing using information technology. Hence, ethics course is beneficial for increasing accounting professionalism especially their intentio to blow the whistle wrongdoing using information technology.

Forebody vortex control for suppressing wing rock on a highly-swept wing configuration

NASA Technical Reports Server (NTRS)

Suarez, Carlos J.; Kramer, Brian R.; Ayers, Bert; Malcolm, Gerald N.

1992-01-01

Free-to-roll tests were conducted in a wind tunnel with a configuration that consisted of a highly-slender forebody and a 78 deg swept delta wing. A limit cycle oscillation was observed for angles of attack between 22 and 30 deg. In general, the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. Various blowing techniques were evaluated as means of wing rock suppression. Blowing tangentially aft from leeward side nozzles near the forebody tip can damp the roll motion at low blowing rates and stop it completely at higher blowing rates. At the high rates, significant vortex asymmetries are created, causing the model to stop at a non-zero roll angle. Forward blowing and alternating right/left pulsed blowing appear to be more efficient techniques for suppressing wing rock. The oscillations can be damped almost completely at lower blowing coefficients, and, apparently, no major vortex asymmetries are induced. Good agreement is observed between this study and previous water tunnel tests on the same configuration.

Wind Tunnel Testing of Powered Lift, All-Wing STOL Model

NASA Technical Reports Server (NTRS)

Collins, Scott W.; Westra, Bryan W.; Lin, John C.; Jones, Gregory S.; Zeune, Cal H.

2008-01-01

Short take-off and landing (STOL) systems can offer significant capabilities to warfighters and, for civil operators thriving on maximizing efficiencies they can improve airspace use while containing noise within airport environments. In order to provide data for next generation systems, a wind tunnel test of an all-wing cruise efficient, short take-off and landing (CE STOL) configuration was conducted in the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) 14- by 22-foot Subsonic Wind Tunnel. The test s purpose was to mature the aerodynamic aspects of an integrated powered lift system within an advanced mobility configuration capable of CE STOL. The full-span model made use of steady flap blowing and a lifting centerbody to achieve high lift coefficients. The test occurred during April through June of 2007 and included objectives for advancing the state-of-the-art of powered lift testing through gathering force and moment data, on-body pressure data, and off-body flow field measurements during automatically controlled blowing conditions. Data were obtained for variations in model configuration, angles of attack and sideslip, blowing coefficient, and height above ground. The database produced by this effort is being used to advance design techniques and computational tools for developing systems with integrated powered lift technologies.

Modeling of Mixing Behavior in a Combined Blowing Steelmaking Converter with a Filter-Based Euler-Lagrange Model

NASA Astrophysics Data System (ADS)

Li, Mingming; Li, Lin; Li, Qiang; Zou, Zongshu

2018-05-01

A filter-based Euler-Lagrange multiphase flow model is used to study the mixing behavior in a combined blowing steelmaking converter. The Euler-based volume of fluid approach is employed to simulate the top blowing, while the Lagrange-based discrete phase model that embeds the local volume change of rising bubbles for the bottom blowing. A filter-based turbulence method based on the local meshing resolution is proposed aiming to improve the modeling of turbulent eddy viscosities. The model validity is verified through comparison with physical experiments in terms of mixing curves and mixing times. The effects of the bottom gas flow rate on bath flow and mixing behavior are investigated and the inherent reasons for the mixing result are clarified in terms of the characteristics of bottom-blowing plumes, the interaction between plumes and top-blowing jets, and the change of bath flow structure.

Characterization of Generalized Young Measures Generated by Symmetric Gradients

NASA Astrophysics Data System (ADS)

De Philippis, Guido; Rindler, Filip

2017-06-01

This work establishes a characterization theorem for (generalized) Young measures generated by symmetric derivatives of functions of bounded deformation (BD) in the spirit of the classical Kinderlehrer-Pedregal theorem. Our result places such Young measures in duality with symmetric-quasiconvex functions with linear growth. The "local" proof strategy combines blow-up arguments with the singular structure theorem in BD (the analogue of Alberti's rank-one theorem in BV), which was recently proved by the authors. As an application of our characterization theorem we show how an atomic part in a BD-Young measure can be split off in generating sequences.

Nuclear quadrupole resonance studies project. [spectrometer design and spectrum analysis

NASA Technical Reports Server (NTRS)

Murty, A. N.

1978-01-01

The participation of undergraduates in nuclear quadrupole resonance research at Grambling University was made possible by NASA grants. Expanded laboratory capabilities include (1) facilities for high and low temperature generation and measurement; (2) facilities for radio frequency generation and measurement with the modern spectrum analyzers, precision frequency counters and standard signal generators; (3) vacuum and glass blowing facilities; and (4) miscellaneous electronic and machine shop facilities. Experiments carried out over a five year period are described and their results analyzed. Theoretical studies on solid state crystalline electrostatic fields, field gradients, and antishielding factors are included.

The effect of blow flies (Diptera: Calliphoridae) on the size and weight of mangos (Mangifera indica L.)

PubMed Central

Naqqash, Muhammad Nadir; Saeed, Qamar; Ghouri, Fozia

2016-01-01

Background: Pollination has a great effect on the yield of fruit trees. Blow flies are considered as an effective pollinator compared to hand pollination in fruit orchards. Therefore, this study was designed to evaluate the effect of different pollination methods in mango orchards. Methodology: The impact of pollination on quantity and quality of mango yield by blow flies was estimated by using three treatments, i.e., open pollinated trees, trees were covered by a net in the presence of blow flies for pollination, and trees were covered with a net but without insects. Results: The maximum number of flowers was recorded in irregular types of inflorescence, i.e., 434.80 flowers/inflorescence. Fruit setting (bud) was higher in open pollinated mango trees (i.e. 37.00/inflorescence) than enclosed pollination by blow flies (i.e. 22.34/inflorescence). The size of the mango fruit was the highest (5.06 mm) in open pollinated tree than those pollinated by blow flies (3.93 mm) and followed by without any pollinator (3.18 mm) at marble stage. We found that the maximum weight of mango fruit (201.19 g) was in open pollinated trees. Discussion: The results demonstrated that blow flies can be used as effective mango pollinators along with other flies and bees. The blow flies have shown a positive impact on the quality and quantity of mango. This study will be helpful in future and also applicable at farm level to use blow flies as pollinators that are cheap and easy to rear. PMID:27441107

Osimertinib, a third-generation tyrosine kinase inhibitor targeting non-small cell lung cancer with EGFR T790M mutations.

PubMed

McCoach, C E; Jimeno, A

2016-10-01

Oncogenic driver mutations in the epidermal growth factor receptor (EGFR) gene have provided a focus for effective targeted therapy. Unfortunately, all patients eventually develop resistance to frontline therapy with EGFR tyrosine kinase inhibitors (TKIs). The majority of patients develop a large subclonal population of tumor cells with a T790M mutation that renders these cells resistant to first-generation TKIs. Osimertinib is a third-generation EGFR TKI that was designed to overcome resistance from T790M mutations. This agent has demonstrated strong preclinical activity, and in the clinic it has demonstrated a high objective response rate and progression-free survival in patients with EGFR double mutations (L858R/T790M and exon 19 deletion/T790M). It is now approved by the FDA for patients who have a documented T790M mutation and who have progressed on a prior TKI. Osimertinib is also approved in the E.U. and Japan. Copyright 2016 Prous Science, S.A.U. or its licensors. All rights reserved.

Detecting Outliers in Marathon Data by Means of the Andrews Plot

NASA Astrophysics Data System (ADS)

Stehlík, Milan; Wald, Helmut; Bielik, Viktor; Petrovič, Juraj

2011-09-01

For an optimal race performance, it is important, that the runner keeps steady pace during most of the time of the competition. First time runners or athletes without many competitions often experience an "blow out" after a few kilometers of the race. This could happen, because of strong emotional experiences or low control of running intensity. Competition pace of half marathon of the middle level recreational athletes is approximately 10 sec quicker than their training pace. If an athlete runs the first third of race (7 km) at a pace that is 20 sec quicker than is his capacity (trainability), he would experience an "blow out" in the last third of the race. This would be reflected by reducing the running intensity and inability to keep steady pace in the last kilometers of the race and in the final time as well. In sports science, there are many diagnostic methods ([3], [2], [6]) that are used for prediction of optimal race pace tempo and final time. Otherwise there is lacking practical evidence of diagnostics methods and its use in the field (competition, race). One of the conditions that needs to be carried out is that athletes have not only similar final times, but it is important that they keep constant pace as much as possible during whole race. For this reason it is very important to find outliers. Our experimental group consisted of 20 recreational trained athletes (mean age 32,6 years±8,9). Before the race the athletes were instructed to run on the basis of their subjective feeling and previous experience. The data (running pace of each kilometer, average and maximal heart rate of each kilometer) were collected by GPS-enabled personal trainer Forerunner 305.

26 CFR 31.3402(g)-1 - Supplemental wage payments.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., wages paid as noncash fringe benefits, sick pay paid by a third party as an agent of the employer... one employer. (ii) Agents. For purposes of paragraph (a)(2) of this section, any payment made to an employee by a third party acting as an agent for the employer (regardless of whether such person shall have...

On lower bounds for possible blow-up solutions to the periodic Navier-Stokes equation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cortissoz, Jean C., E-mail: jcortiss@uniandes.edu.co; Montero, Julio A., E-mail: ja.montero907@uniandes.edu.co; Pinilla, Carlos E., E-mail: ce.pinilla108@uniandes.edu.co

2014-03-15

We show a new lower bound on the H{sup .3/2} (T{sup 3}) norm of a possible blow-up solution to the Navier-Stokes equation, and also comment on the extension of this result to the whole space. This estimate can be seen as a natural limiting result for Leray's blow-up estimates in L{sup p}(R{sup 3}), 3 < p < ∞. We also show a lower bound on the blow-up rate of a possible blow-up solution of the Navier-Stokes equation in H{sup .5/2} (T{sup 3}), and give the corresponding extension to the case of the whole space.

Blow-Out Velocities of Solutions of Hydrocarbons and Boron Hydride - Hydrocarbon Reaction Products in a 1 7/8-Inch-Diameter Combustor

NASA Technical Reports Server (NTRS)

Morris, James F.; Lord, Albert M.

1957-01-01

Blow-out velocities were determined for JP-4 solutions containing: (1) 10 % ethylene - decaborane reaction product, (2) 10% and 20% acetylene - diborane reaction product, and (3) 5.5%, 15.7%, and 30.7% methylacetylene - diborane reaction product. These were compared with blow-out velocities for JP-4, propylene oxide, and neohexane and previously reported data for JP-4 solutions of pentaborane. For those reaction products investigated, the blow-out velocities at a fixed equivalence ratio were higher for those materials containing higher boron concentrations; that is, blow-out velocity increased in the following order: (1) methylacetylene - diborane, (2) acetylene - diborane, and (3) ethylene - decaborane reaction products.

A One-Dimensional Global-Scaling Erosive Burning Model Informed by Blowing Wall Turbulence

NASA Technical Reports Server (NTRS)

Kibbey, Timothy P.

2014-01-01

A derivation of turbulent flow parameters, combined with data from erosive burning test motors and blowing wall tests results in erosive burning model candidates useful in one-dimensional internal ballistics analysis capable of scaling across wide ranges of motor size. The real-time burn rate data comes from three test campaigns of subscale segmented solid rocket motors tested at two facilities. The flow theory admits the important effect of the blowing wall on the turbulent friction coefficient by using blowing wall data to determine the blowing wall friction coefficient. The erosive burning behavior of full-scale motors is now predicted more closely than with other recent models.

Large-Scale Wind-Tunnel Tests of an Airplane Model with an Unswept, Aspect-Ratio-10 Wing, Two Propellers, and Blowing Flaps

NASA Technical Reports Server (NTRS)

Griffin, Roy N., Jr.; Holzhauser, Curt A.; Weiberg, James A.

1958-01-01

An investigation was made to determine the lifting effectiveness and flow requirements of blowing over the trailing-edge flaps and ailerons on a large-scale model of a twin-engine, propeller-driven airplane having a high-aspect-ratio, thick, straight wing. With sufficient blowing jet momentum to prevent flow separation on the flap, the lift increment increased for flap deflections up to 80 deg (the maximum tested). This lift increment also increased with increasing propeller thrust coefficient. The blowing jet momentum coefficient required for attached flow on the flaps was not significantly affected by thrust coefficient, angle of attack, or blowing nozzle height.

Augmenting ejector endwall effects. [V/STOL aircraft

NASA Technical Reports Server (NTRS)

Porter, J. L.; Squyers, R. A.

1979-01-01

Rectangular inlet ejectors which had multiple hypermixing nozzles for their primary jets were investigated for the effects of endwall blowing on thrust augmentation performance. The ejector configurations tested had both straight wall and active boundary layer control type diffusers. Endwall flows were energized and controlled by simple blowing jets suitably located in the ejector. Both the endwall and boundary layer control diffuser blowing rates were varied to determine optimum performance. High area ratio diffusers with insufficient endwall blowing showed endwall separation and rapid degradation of thrust performance. Optimized values of diffuser boundary layer control and endwall nozzle blowing rates in an ejector augmenter were shown to achieve high levels of augmentation performance for maximum compactness.

The role of alectinib in the treatment of advanced ALK-rearranged non-small-cell lung cancer.

PubMed

Srinivasamaharaj, Srividya; Salame, Bilal Khameze; Rios-Perez, Jorge; Kloecker, Goetz; Perez, Cesar A

2016-12-01

The identification of anaplastic lymphoma kinase (ALK) gene rearrangements in subsets of non-small cell lung cancer patients has provided with unparalleled opportunities to hinder the progression of this disease through targeting the activity of these specific molecules. Unfortunately most patients develop disease progression in less than a year of treatment with crizotinib, the first-generation ALK-inhibitor. Areas covered: We review the resistance mechanisms to ALK inhibitors as well as an overview of the clinical activity of the alectinib, a second generation ALK inhibitor. Expert commentary: Second generation ALK inhibitors as alectinib and ceritinib can overcome crizotinib-resistant mutations and improve central nervous system control. Novel third-generation inhibitors and combination of agents give hope of achieving an even longer disease control in the next decade.

Reduced-Pressure Foaming of Aluminum Alloys

NASA Astrophysics Data System (ADS)

Vinod Kumar, G. S.; Mukherjee, M.; Garcia-Moreno, F.; Banhart, J.

2013-01-01

We developed a novel process for foaming aluminum and its alloys without using a blowing agent. The process involves a designated apparatus in which molten aluminum and its alloys are first foamed under reduced pressure and then solidified quickly. Foaming was done for pure aluminum (99.99 pct) and AlMg5 alloy not containing stabilizing particles and AlMg5 and AlSi9Mg5 alloys containing 5 vol pct SiO2 particles. We discuss the foaming mechanism and develop a model for estimating the porosity that can be achieved in this process. The nucleation of pores in foams is also discussed.

Water-free synthesis of polyurethane foams using highly reactive diisocyanates derived from 5-hydroxymethylfurfural.

PubMed

Neumann, Christopher N D; Bulach, Winfried D; Rehahn, Matthias; Klein, Roland

2011-09-01

This paper reports on the synthesis of a new highly reactive diisocyanate monomer based on hydroxymethylfurfural. It further describes its catalyst-free conversion to linear-chain thermoplastic polyurethanes as well as to cross-linked polyurethane foams. In addition, a novel strategy for the synthesis of polyurethane foams without the necessity of using water is developed. Nitrogen is utilized herein as blowing agent which is formed during Curtius rearrangement of a new furan based carboxylic azide into its corresponding diisocyanate. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

2-hydroxyethyl metahcrylate/gelatin based superporous hydrogels for tissue regeneration

NASA Astrophysics Data System (ADS)

Tomić, Simonida Lj.; Babić, Marija M.; Vuković, Jovana S.; Perišić, Marija D.; Filipović, Vuk V.; Davidović, Sladjana Z.; Filipović, Jovanka M.

2016-05-01

In this study, superporous hydrogels were synthesized by free radical polymerization of 2-hydroxyethyl methacrylate without and in the presence of gelatin. Highly porous hydrogel structures were obtained by two different techniques: using a gas blowing agent, sodium bicarbonate, and a cryogenic treatment followed by freeze-drying. After the gel synthesis, gelatin molecules were covalently immobilised onto PHEMA via glytaraldehyde activation. All samples were characterized for morphological, mechanical, swelling and antibacterial properties. The results obtained show that samples with gelatin show better properties in comparison with PHEMA samples, which make these materials highly attractive for developing hydrogel scaffolds for tissue regeneration.

Mesoporous silica nanoparticles decorated with polycationic dendrimers for infection treatment.

PubMed

González, Blanca; Colilla, Montserrat; Díez, Jaime; Pedraza, Daniel; Guembe, Marta; Izquierdo-Barba, Isabel; Vallet-Regí, María

2018-03-01

This work aims to provide an effective and novel solution for the treatment of infection by using nanovehicles loaded with antibiotics capable of penetrating the bacterial wall, thus increasing the antimicrobial effectiveness. These nanosystems, named "nanoantibiotics", are composed of mesoporous silica nanoparticles (MSNs), which act as nanocarriers of an antimicrobial agent (levofloxacin, LEVO) localized inside the mesopores. To provide the nanosystem of bacterial membrane interaction capability, a polycationic dendrimer, concretely the poly(propyleneimine) dendrimer of third generation (G3), was covalently grafted to the external surface of the LEVO-loaded MSNs. After physicochemical characterization of this nanoantibiotic, the release kinetics of LEVO and the antimicrobial efficacy of each released dosage were evaluated. Besides, internalization studies of the MSNs functionalized with the G3 dendrimer were carried out, showing a high penetrability throughout Gram-negative bacterial membranes. This work evidences that the synergistic combination of polycationic dendrimers as bacterial membrane permeabilization agents with LEVO-loaded MSNs triggers an efficient antimicrobial effect on Gram-negative bacterial biofilm. These positive results open up very promising expectations for their potential application in new infection therapies. Seeking new alternatives to current available treatments of bacterial infections represents a great challenge in nanomedicine. This work reports the design and optimization of a new class of antimicrobial agent, named "nanoantibiotic", based on mesoporous silica nanoparticles (MSNs) decorated with polypropyleneimine dendrimers of third generation (G3) and loaded with levofloxacin (LEVO) antibiotic. The covalently grafting of these G3 dendrimers to MSNs allows an effective internalization in Gram-negative bacteria. Furthermore, the LEVO loaded into the mesoporous cavities is released in a sustained manner at effective antimicrobial dosages. The novelty and originality of this manuscript relies on proving that the synergistic combination of bacteria-targeting and antimicrobial agents into a unique nanosystem provokes a remarkable antimicrobial effect against bacterial biofilm. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

PIV Measurements on a Blowing Flap

NASA Technical Reports Server (NTRS)

Hutcheson, Florence V.; Stead, Daniel J.

2004-01-01

PIV measurements of the flow in the region of a flap side edge are presented for several blowing flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main-element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the vortex system or accelerated the merging of the side vortex to the flap top surface. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Lead sulfate nano- and microparticles in the acid plant blow-down generated at the sulfuric acid plant of the El Teniente mine, Chile.

PubMed

Barassi, Giancarlo M; Klimsa, Martin; Borrmann, Thomas; Cairns, Mathew J; Kinkel, Joachim; Valenzuela, Fernando

2014-12-01

The acid plant 'blow-down' (also called weak acid) produced at El Teniente mine in Chile was characterized. This liquid waste (tailing) is generated during the cooling and cleaning of the smelter gas prior to the production of sulfuric acid. The weak acid was composed of a liquid and a solid phase (suspended solids). The liquid phase of the sample analyzed in this study mainly contained Cu (562 mg L(-1)), SO4(2-) (32 800 mg L(-1)), Ca (1449 mg L(-1)), Fe (185 mg L(-1)), As (6 mg L(-1)), K (467 mg L(-1)) and Al (113 mg L(-1)). Additionally, the sample had a pH-value and total acidity of 0.45 and 2970 mg L(-1) as CaCO3, respectively. Hence, this waste was classified as extremely acidic and with a high metal content following the Ficklin diagram classification. Elemental analysis using atomic absorption, inductively coupled plasma, X-ray diffraction and electron microscopy showed that the suspended solids were anglesite (PbSO4) nano- and microparticles ranging from 50 nm to 500 nm in diameter.

Dead-blow hammer design applied to a calibration target mechanism to dampen excessive rebound

NASA Technical Reports Server (NTRS)

Lim, Brian Y.

1991-01-01

An existing rotary electromagnetic driver was specified to be used to deploy and restow a blackbody calibration target inside of a spacecraft infrared science instrument. However, this target was much more massive than any other previously inherited design applications. The target experienced unacceptable bounce when reaching its stops. Without any design modification, the momentum generated by the driver caused the target to bounce back to its starting position. Initially, elastomeric dampers were used between the driver and the target. However, this design could not prevent the bounce, and it compromised the positional accuracy of the calibration target. A design that successfully met all the requirements incorporated a sealed pocket 85 percent full of 0.75 mm diameter stainless steel balls in the back of the target to provide the effect of a dead-blow hammer. The energy dissipation resulting from the collision of balls in the pocket successfully dampened the excess momentum generated during the target deployment. The disastrous effects of new requirements on a design with a successful flight history, the modifications that were necessary to make the device work, and the tests performed to verify its functionality are described.

NaOCl degradation of a HEMA-free all-in-one adhesive bonded to enamel and dentin following two air-blowing techniques.

PubMed

De Munck, Jan; Ermis, R Banu; Koshiro, Kenichi; Inoue, Satoshi; Ikeda, Takatsumi; Sano, Hidehiko; Van Landuyt, Kirsten L; Van Meerbeek, Bart

2007-01-01

Phase-separation within HEMA-free all-in-one dental adhesives may result in the entrapment of droplets within the adhesive resin. Strongly air-blowing prior to polymerization, can remove most of these droplets. The objective of this study was to evaluate the effect these droplets may have on the resistance of the adhesive-tooth interface to NaOCl degradation. The micro-tensile bond strength (microTBS) to enamel and dentin was determined when a HEMA-free all-in-one adhesive was applied either following a mild or strong air-blowing technique. The bonds were also exposed to an aqueous sodium hypochlorite (NaOCl) solution for 1h, following a recently introduced methodology to mimic in vivo bond degradation. This study revealed that strong air-blowing of the adhesive only resulted in a significantly higher micro-tensile bond strength (microTBS) to dentin, but not to enamel. Likewise, NaOCl only reduced the microTBS to dentin for both the mild and strong air-blowing technique, but again not the microTBS to enamel. Failure analysis by SEM clearly revealed that strong air-blowing is less effective in droplet removal when the adhesive was applied in small and narrow class-I cavities, as compared to when it was applied to flat surfaces. NaOCl did preferentially dissolve the hybrid layer at dentin, and more for the mild than for the strong air-blowing technique. A strong air-blowing procedure resulted in a more NaOCl-resistant hybrid layer, so that it can be concluded that a HEMA-free one-step adhesive definitely benefits from a strong air-blowing technique.

Whistle-blowing process in healthcare: From suspicion to action.

PubMed

Pohjanoksa, Johanna; Stolt, Minna; Suhonen, Riitta; Löyttyniemi, Eliisa; Leino-Kilpi, Helena

2017-01-01

Whistle-blowing is an ethical activity that tries to end wrongdoing. Wrongdoing in healthcare varies from inappropriate behaviour to illegal action. Whistle-blowing can have negative consequences for the whistle-blower, often in the form of bullying or retribution. Despite the wrongdoing and negative tone of whistle-blowing, there is limited literature exploring them in healthcare. The aim was to describe possible wrongdoing in Finnish healthcare and to examine whistle-blowing processes described on the basis of the existing literature in healthcare as perceived by healthcare professionals. The study was a cross-sectional descriptive survey. The data were collected using the electronic questionnaire Whistle-blowing in Health Care and analysed statistically. Participants and research context: A total of 397 Finnish healthcare professionals participated, 278 of whom had either suspected or observed wrongdoing in healthcare, which established the data for this article. Ethical considerations: Ethical approval was obtained from the Ethics Committee of the University (20/2015). Permission to conduct the study was received according to the organisation's policies. Wrongdoing occurs in healthcare, as 96% of the participants had suspected and 94% had observed wrongdoing. Regarding the frequency, wrongdoing was suspected (57%) and observed (52%) more than once a month. Organisation-related wrongdoing was the most common type of wrongdoing (suspected 70%, observed 66%). In total, two whistle-blowing processes were confirmed in healthcare: (1) from suspicion to consequences occurred to 27%, and (2) from observation to consequences occurred to 37% of the participants. Wrongdoing occurs in healthcare quite frequently. Whistle-blowing processes were described based on the existing literature, but two separate processes were confirmed by the empirical data. More research is needed on wrongdoing and whistle-blowing on it in healthcare.

Clinical roundtable monograph: Unmet needs in the management of chronic myelogenous leukemia.

PubMed

Jabbour, Elias J; Bixby, Dale; Akard, Luke P

2012-12-01

Approximately 5,000 cases of chronic myelogenous leukemia (CML) are diagnosed each year in the United States. The introduction of tyrosine kinase inhibitors (TKIs) has dramatically improved survival time for many CML patients. Current first-line treatment options include imatinib and the second-generation agents nilotinib and dasatinib. Second- and third-line agents include nilotinib, dasatinib, bosutinib, and the new agent ponatinib. Despite the effectiveness of TKIs, some patients develop resistance or intolerance to these agents. A number of mutations of the BCR-ABL gene have been identified and are associated with TKI resistance. Patients may benefit from switching to a second-line TKI, undergoing hematopoietic stem cell transplant, or receiving newly emerging agents. Although early response is associated with improved patient outcome, clinicians lack tests that can determine which patients will benefit from which therapies. To ensure adequate response, patients should be monitored by both polymerase chain reaction and cytogenetic analysis of the bone marrow. This roundtable monograph reviews key unmet needs in patients with CML related to disease management and treatment options.

Glass shell manufacturing in space. [residual gases in spherical shells made from metal-organic gels

NASA Technical Reports Server (NTRS)

Nolen, R. J.; Ebner, M. A.; Downs, R. L.

1980-01-01

Residual gases always found in glass shells are CO2, O2 and N2. In those cases where high water vapor pressure is maintained in the furnace, water is also found in the shells. Other evidence for the existence of water in shells is the presence of water-induced surface weathering of the interior shell surface. Water and CO2 are the predominant volatiles generated by the pyrolysis of both inorganic and hydrolyzed metal-organic gels. The pyrolysates of unhydrolyzed metal-organic gels also contain, in addition to water and CO2, significant levels of organic volatiles, such as ethanol and some hydrocarbons; on complete oxidation, these produce CO2 and water as well. Water is most likely the initial blowing agent, it is produced copiously during the initial stages of heating. In the later stages, CO2 becomes the dominant gas as H2O is lost at increasing rates. Water in the shell arises mainly from gel dehydration, CO2 by sodium bicarbonate/carbonate decomposition and carbon oxidation, and O2 and N2 by permeation of the ambient furnace air through the molten shell wall.

The Effects of Blowing Over Various Trailing-edge Flaps on an NACA 0006 Airfoil Section, Comparisons with Various Types of Flaps on other Airfoil Sections, and an Analysis of Flow and Power Relationships for Blowing Systems

NASA Technical Reports Server (NTRS)

Dods, J. B., Jr.; Watson, E. C.

1976-01-01

The results are presented of a two-dimensional investigation conducted to determine the effect of blowing over various types of trailing-edge flaps on a wing having the NACA 0006 airfoil section and a drooped-nose flap. The position and profile of the trailing-edge flap, the nozzle height, and the location of the flap with respect to the nozzle were found to be important variables. Data from many investigations were used to make an evaluation of the effects of blowing on lift. An analysis was made of flow and power relationships for blowing systems.

Trailing Edge Blowing on a Two-Dimensional Six-Percent Thick Elliptical Circulation Control Airfoil Up to Transonic Conditions

NASA Technical Reports Server (NTRS)

Alexander, Michael G.; Anders, Scott G.; Johnson, Stuart K.; Florance, Jennifer P.; Keller, Donald F.

2005-01-01

A wind tunnel test was conducted in the NASA Langley Transonic Dynamics Tunnel (TDT) on a six percent thick slightly cambered elliptical circulation control airfoil with both upper and lower surface blowing capability. Parametric evaluations of jet slot heights and Coanda surface shapes were conducted at momentum coefficients (Cm) from 0.0 to 0.12. Test data were acquired at Mach numbers of 0.3, 0.5, 0.7, 0.8, and 0.84 at Reynolds numbers per foot of 2.43 x 105 to 1.05 x 106. For a transonic condition, (Mach = 0.8 at alpha = 3 degrees), it was generally found the smaller slot and larger Coanda surface combination was overall more effective than other slot/Coanda surface combinations. Lower surface blowing was not as effective as the upper surface blowing over the same range of momentum coefficients. No appreciable Coanda surface, slot height, or slot blowing position preference was indicated transonically with the dual slot blowing.

Effects of spanwise blowing on the pressure field and vortex-lift characteristics of a 44 deg swept trapezoidal wing. [wind tunnel stability tests - aircraft models

NASA Technical Reports Server (NTRS)

Campbell, J. F.

1975-01-01

Wind-tunnel data were obtained at a free-stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and jet location. Results of this study show that the sectional effects to spanwise blowing are strongly dependent on angle of attack, jet thrust coefficient, and span location; the largest effects occur at the highest angles of attack and thrust coefficients and on the inboard portion of the wing. Full vortex lift was achieved at the inboard span station with a small blowing rate, but successively higher blowing rates were necessary to achieve full vortex lift at increased span distances. It is shown that spanwise blowing increases lift throughout the angle-of-attack range, delays wing stall to higher angles of attack, and improves the induced-drag polars. The leading-edge suction analogy can be used to estimate the section and total lifts resulting from spanwise blowing.

Screening of nerve agent degradation products by MALDI-TOFMS.

PubMed

Shu, You-Ren; Su, An-Kai; Liu, Ju-Tsung; Lin, Cheng-Huang

2006-07-01

A novel method for the rapid screening of degradation products derived from nerve agents by matrix-assisted laser desorption ionization time-of-flight mass spectrometry is described. Five standard products were selected as model compounds, including isopropyl methylphosphonic acid (IMPA), pinacolyl methylphosphonic acid (PMPA), ethyl methylphosphonic acid (EMPA), isobutyl methylphosphonic acid (i-BuMPA), and cyclohexyl methylphosphonic acid (CHMPA), which are degradation products of Sarin (GB), Soman (GD), VX, Russian VX (RVX), and GF, respectively. For comparison, CHCA (alpha-cyano-4-hydroxycinnamic acid) and DCCA (7-(diethylamino)coumarin-3-carboxylic acid) were used as the MALDI-matrix when the third harmonic generation (355 nm) of a Nd:YAG laser and a hydrogen Raman laser (multifrequency laser) were used, respectively. The method permitted the five nerve agent degradation products to be screened rapidly and successfully, suggesting that it has the potential for use as a routine monitoring tool.

Direct Simulation of Evolution and Control of Three-Dimensional Instabilities in Attachment-Line Boundary Layers

NASA Technical Reports Server (NTRS)

Joslin, Ronald D.

1995-01-01

The spatial evolution of three-dimensional disturbances in an attachment-line boundary layer is computed by direct numerical simulation of the unsteady, incompressible Navier-Stokes equations. Disturbances are introduced into the boundary layer by harmonic sources that involve unsteady suction and blowing through the wall. Various harmonic- source generators are implemented on or near the attachment line, and the disturbance evolutions are compared. Previous two-dimensional simulation results and nonparallel theory are compared with the present results. The three-dimensional simulation results for disturbances with quasi-two-dimensional features indicate growth rates of only a few percent larger than pure two-dimensional results; however, the results are close enough to enable the use of the more computationally efficient, two-dimensional approach. However, true three-dimensional disturbances are more likely in practice and are more stable than two-dimensional disturbances. Disturbances generated off (but near) the attachment line spread both away from and toward the attachment line as they evolve. The evolution pattern is comparable to wave packets in at-plate boundary-layer flows. Suction stabilizes the quasi-two-dimensional attachment-line instabilities, and blowing destabilizes these instabilities; these results qualitatively agree with the theory. Furthermore, suction stabilizes the disturbances that develop off the attachment line. Clearly, disturbances that are generated near the attachment line can supply energy to attachment-line instabilities, but suction can be used to stabilize these instabilities.

Dogs Identify Agents in Third-Party Interactions on the Basis of the Observed Degree of Contingency.

PubMed

Tauzin, Tibor; Kovács, Krisztina; Topál, József

2016-08-01

To investigate whether dogs could recognize contingent reactivity as a marker of agents' interaction, we performed an experiment in which dogs were presented with third-party contingent events. In the perfect-contingency condition, dogs were shown an unfamiliar self-propelled agent (SPA) that performed actions corresponding to audio clips of verbal commands played by a computer. In the high-but-imperfect-contingency condition, the SPA responded to the verbal commands on only two thirds of the trials; in the low-contingency condition, the SPA responded to the commands on only one third of the trials. In the test phase, the SPA approached one of two tennis balls, and then the dog was allowed to choose one of the balls. The proportion of trials on which a dog chose the object indicated by the SPA increased with the degree of contingency: Dogs chose the target object significantly above chance level only in the perfect-contingency condition. This finding suggests that dogs may use the degree of temporal contingency observed in third-party interactions as a cue to identify agents. © The Author(s) 2016.

Computational studies of the effects of active and passive circulation enhancement concepts on wind turbine performance

NASA Astrophysics Data System (ADS)

Tongchitpakdee, Chanin

With the advantage of modern high speed computers, there has been an increased interest in the use of first-principles based computational approaches for the aerodynamic modeling of horizontal axis wind turbine (HAWT). Since these approaches are based on the laws of conservation (mass, momentum, and energy), they can capture much of the physics in great detail. The ability to accurately predict the airloads and power output can greatly aid the designers in tailoring the aerodynamic and aeroelastic features of the configuration. First-principles based analyses are also valuable for developing active means (e.g., circulation control), and passive means (e.g., Gurney flaps) of reducing unsteady blade loads, mitigating stall, and for efficient capture of wind energy leading to more electrical power generation. In this present study, the aerodynamic performance of a wind turbine rotor equipped with circulation enhancement technology (trailing edge blowing or Gurney flaps) is investigated using a three-dimensional unsteady viscous flow analysis. The National Renewable Energy Laboratory (NREL) Phase VI horizontal axis wind turbine is chosen as the baseline configuration. Prior to its use in exploring these concepts, the flow solver is validated with the experimental data for the baseline case under yawed flow conditions. Results presented include radial distribution of normal and tangential forces, shaft torque, root flap moment, surface pressure distributions at selected radial locations, and power output. Results show that good agreement has been for a range of wind speeds and yaw angles, where the flow is attached. At high wind speeds, however, where the flow is fully separated, it was found that the fundamental assumptions behind this present methodology breaks down for the baseline turbulence model (Spalart-Allmaras model), giving less accurate results. With the implementation of advanced turbulence model, Spalart-Allmaras Detached Eddy Simulation (SA-DES), the accuracy of the results at high wind speeds are improved. Results of circulation enhancement concepts show that, at low wind speed (attached flow) conditions, a Coanda jet at the trailing edge of the rotor blade is effective at increasing circulation resulting in an increase of lift and the chordwise thrust force. This leads to an increased amount of net power generation compared to the baseline configuration for moderate blowing coefficients. The effects of jet slot height and pulsed jet are also investigated in this study. A passive Gurney flap was found to increase the bound circulation and produce increased power in a manner similar to the Coanda jet. At high wind speed where the flow is separated, both the Coanda jet and Gurney flap become ineffective. Results of leading edge blowing indicate that a leading edge blowing jet is found to be beneficial in increasing power generation at high wind speeds. The effect of Gurney flap angle is also studied. Gurney flap angle has significant influence in power generation. Higher power output is obtained at higher flap angles.

Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route

PubMed Central

Hangai, Yoshihiko; Kamada, Hiroto; Utsunomiya, Takao; Kitahara, Soichiro; Kuwazuru, Osamu; Yoshikawa, Nobuhiro

2014-01-01

Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%–78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT) observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE) analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis. PMID:28788573

Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route.

PubMed

Hangai, Yoshihiko; Kamada, Hiroto; Utsunomiya, Takao; Kitahara, Soichiro; Kuwazuru, Osamu; Yoshikawa, Nobuhiro

2014-03-21

Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%-78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT) observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE) analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis.

An overview of fotemustine in high-grade gliomas: from single agent to association with bevacizumab.

PubMed

Lombardi, Giuseppe; Farina, Patrizia; Della Puppa, Alessandro; Cecchin, Diego; Pambuku, Ardi; Bellu, Luisa; Zagonel, Vittorina

2014-01-01

Fotemustine is a third-generation nitrosourea showing efficacy in various types of tumors such as melanoma and glioma. We reviewed the most important studies on fotemustine treatment in glioma patients analyzing its pharmacological profile and its activity and safety. Fotemustine was used as single agent or in association with new targeted drugs such as bevacizumab; fotemustine was used both as first-line chemotherapy before temozolomide era and in refractory-temozolomide patients during temozolomide era. Finally, analyzing and comparing the activity and safety of fotemustine alone or in combination with bevacizumab versus other nitrosoureas such as lomustine, we may suggest that the combination treatment with bevacizumab and fotemustine may be active and tolerable in patients with high grade gliomas.

An Overview of Fotemustine in High-Grade Gliomas: From Single Agent to Association with Bevacizumab

PubMed Central

Lombardi, Giuseppe; Farina, Patrizia; Della Puppa, Alessandro; Cecchin, Diego; Pambuku, Ardi; Bellu, Luisa; Zagonel, Vittorina

2014-01-01

Fotemustine is a third-generation nitrosourea showing efficacy in various types of tumors such as melanoma and glioma. We reviewed the most important studies on fotemustine treatment in glioma patients analyzing its pharmacological profile and its activity and safety. Fotemustine was used as single agent or in association with new targeted drugs such as bevacizumab; fotemustine was used both as first-line chemotherapy before temozolomide era and in refractory-temozolomide patients during temozolomide era. Finally, analyzing and comparing the activity and safety of fotemustine alone or in combination with bevacizumab versus other nitrosoureas such as lomustine, we may suggest that the combination treatment with bevacizumab and fotemustine may be active and tolerable in patients with high grade gliomas. PMID:24800248

Awareness and Ethical Orientation of Alternatively Certified Prospective Teachers to Intention for Whistle Blowing

ERIC Educational Resources Information Center

Toker Gokce, Asiye

2013-01-01

This study inquires whistle blowing intentions of alternatively certified prospective teachers, investigating their moral reasoning to blow the whistle. Specifically three hypotheses were tested: Overall ethical awareness of the alternatively certified prospective teachers is high; the participants will identify reasons related to philosophical…

Effect of Pylon Wake with and Without Pylon Blowing on Propeller Thrust

NASA Technical Reports Server (NTRS)

Gentry, Garl L., Jr.; Booth, Earl R., Jr.; Takallu, M. A.

1990-01-01

Pylon trailing edge blowing was investigated as a means of alleviating the effects of the pylon wake on a pusher arrangement of an advanced single-rotation turboprop. Measurements were made of steady-state propeller thrust and pylon wake pressures and turbulence levels with and without blowing. Results show that the pylon trailing edge blowing practically eliminated the pylon wake, significantly reduced the pylon wake turbulence, and had a relatively small effect on the steady-state propeller thrust. The data are presented with a minimum of analysis.

INTERIOR VIEW SHOWING QBOP FURNACE IN BLOW. OXYGEN AND NATURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW SHOWING Q-BOP FURNACE IN BLOW. OXYGEN AND NATURAL GAS ARE BLOWN INTO THE FURNACE THROUGH THE TUYERES TO CHARGE 460,000 LBS. OF HOT METAL, 100,000 LBS. OF SCRAP WITH 30,000 LBS. OF LIME. BLOW TIME IS 16 MINUTES. THE TIME TO BLOW AND TAP THE FURNACES OF THE RESULTING 205,000 TONS OF STEEL AND SLAG IS 35 MINUTES. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

The collision of masses and the way prices react to expectations

NASA Astrophysics Data System (ADS)

Chavez-Guzman, Luis

2004-12-01

When a body is impacted by other bodies its position is determined by the force of the impacts, likewise the price of a share is determined by expectations. This study intents to establish taxonomy of expectations based on the different types of impacts a body can receive, these can be: a blow without penetration, a blow that penetrates and stays in the body, a blow that goes through the body without affecting the body mass, and lastly, a blow that reduces but does not penetrate the body mass.

Numerical and experimental study of blowing jet on a high lift airfoil

NASA Astrophysics Data System (ADS)

Bobonea, A.; Pricop, M. V.

2013-10-01

Active manipulation of separated flows over airfoils at moderate and high angles of attack in order to improve efficiency or performance has been the focus of a number of numerical and experimental investigations for many years. One of the main methods used in active flow control is the usage of blowing devices with constant and pulsed blowing. Through CFD simulation over a 2D high-lift airfoil, this study is trying to highlight the impact of pulsed blowing over its aerodynamic characteristics. The available wind tunnel data from INCAS low speed facility are also beneficial for the validation of the numerical analysis. This study intends to analyze the impact of the blowing jet velocity and slot geometry on the efficiency of an active flow control.

Fledging success is a poor indicator of the effects of bird blow flies on ovenbird survival

USGS Publications Warehouse

Peterson, Sean M.; Streby, Henry M.; Kapfer, Paul M.

2009-01-01

Infestations of bird blow flies (Protocalliphora spp. and Trypocalliphora braueri) have various negative effects on the condition of nestling birds. In the absence of other stressors such as inclement weather, however, infestation alone rarely reduces fledging success. Previous studies have documented effects of blow flies on nestling condition and fledging success. Without information regarding fledgling survival, the full effect of blow-fly infestation remains unclear. To fully investigate the effect of blow-fly infestation on reproductive success of the Ovenbird (Seiurus aurocapilla), we monitored infested and non-infested nests and monitored fledglings from each by using radio telemetry. Blow flies did not affect birds during the nestling period, as brood size, mean nestling mass, fledging success, and time to fledging in infested and non-infested nests were no different. Fledgling survival and minimum distance traveled the first day after fledging, however, were significantly lower for infected fledglings than for those that were not infected. We conclude that the stress of the early fledgling period combined with recent or concurrent blow-fly infection increases mortality in young Oven-birds. Our results demonstrate the importance of including the post-fledging period in investigations of the effects of ectoparasitic infestations on birds.

Assessment of Potential Aerodynamic Benefits from Spanwise Blowing at the Wing Tip. Ph.D. Thesis - George Washington Univ.

NASA Technical Reports Server (NTRS)

Mineck, Raymond Edward

1992-01-01

A comprehensive set of experimental and analytical investigations have been conducted to assess the potential aerodynamic benefits from spanwise blowing at the tip of a moderate aspect ratio, swept wing. An analytical model has been developed to simulate a jet exhausting from the wing tip. An experimental study of a subsonic jet exhausting from the wing tip was conducted to investigate the effect of spanwise blowing from the tip on the aerodynamic characteristics of a moderate aspect ratio, swept wing. Wing force and moment data and surface pressure data were measured at Mach numbers up to 0.72. Results indicate that small amounts of blowing from small jets increase the lift curve slope a small amount, but have no effect on drag. Larger amounts of blowing from longer jets blowing increases lift near the tip and reduce drag at low Mach numbers. These benefits decrease with increasing Mach number, and vanish at Mach 0.5. A Navier-Stokes solver with modified boundary conditions at the tip was used to extrapolate the results to a Mach number of 0.72. With current technology and conventional wing shapes, spanwise blowing at the wing tip does not appear to be a practical means of reducing drag of moderate aspect ratio wings at high subsonic Mach numbers.

Lean Blow-out Studies in a Swirl Stabilized Annular Gas Turbine Combustor

NASA Astrophysics Data System (ADS)

Mishra, R. K.; Kishore Kumar, S.; Chandel, Sunil

2015-05-01

Lean blow out characteristics in a swirl stabilized aero gas turbine combustor have been studied using computational fluid dynamics. For CFD analysis, a 22.5° sector of an annular combustor is modeled using unstructured tetrahedral meshes comprising 1.2 × 106 elements. The governing equations are solved using the eddy dissipation combustion model in CFX. The primary combustion zone is analyzed by considering it as a well stirred reactor. The analysis has been carried out for different operating conditions of the reactants entering into the control volume. The results are treated as the base-line or reference values. Combustion lean blow-out limits are further characterized studying the behavior of combustion zone during transient engine operation. The validity of the computational study has been established by experimental study on a full-scale annular combustor in an air flow test facility that is capable of simulating different conditions at combustor inlet. The experimental result is in a good agreement with the analytical predictions. Upon increasing the combustor mass flow, the lean blow out limit increases, i.e., the blow out occurs at higher fuel-air ratios. In addition, when the operating pressure decreases, the lean blow out limit increases, i.e., blow out occurs at higher fuel-air ratios.

Study of potential aerodynamic benefits from spanwise blowing at wingtip. Ph.D. Thesis - George Washington Univ., 1992

NASA Technical Reports Server (NTRS)

Mineck, Raymond E.

1995-01-01

Comprehensive experimental and analytical studies have been conducted to assess the potential aerodynamic benefits from spanwise blowing at the tip of a moderate-aspect-ratio swept wing. Previous studies on low-aspect-ratio wings indicated that blowing from the wingtip can diffuse the tip vortex and displace it outward. The diffused and displaced vortex will induce a smaller downwash at the wing, and consequently the wing will have increased lift and decreased induced drag at a given angle of attack. Results from the present investigation indicated that blowing from jets with a short chord had little effect on lift or drag, but blowing from jets with a longer chord increased lift near the tip and reduced drag at low Mach numbers. A Navier-Stokes solver with modified boundary conditions at the tip was used to extrapolate the results to a Mach number of 0.72. Calculations indicated that lift and drag increase with increasing jet momentum coefficient. Because the momentum of the jet is typically greater than the reduction in the wing drag and the increase in the wing lift due to spanwise blowing is small, spanwise blowing at the wingtip does not appear to be a practical means of improving the aerodynamic efficiency of moderate-aspectratio swept wings at high subsonic Mach numbers.

Clinical roundtable monograph: Emerging treatment options for TKI-resistant chronic myelogenous leukemia.

PubMed

Cortes, Jorge; Radich, Jerald; Mauro, Michael J

2012-10-01

The development of tyrosine kinase inhibitors (TKIs) that inhibit signaling of the constitutive BCR-ABL protein revolutionized the treatment of chronic myelogenous leukemia (CML). These agents have dramatically changed the treatment landscape for CML, shifting the use of allogeneic stem cell transplantation to selected patients in the salvage setting. Four BCR-ABL TKIs are now commercially available for the treatment of CML: the first-generation TKI imatinib, and the second-generation TKIs dasatinib, nilotinib, and bosutinib. Continuous treatment with these agents induces durable responses in a high proportion of patients with chronic-phase CML. Research is focused on identifying which patients can discontinue therapy without a recurrence of disease. For the group of patients with resistance to TKIs, multiple alternative therapies are being evaluated. The third-generation TKI ponatinib is a BCR-ABL inhibitor that has demonstrated significant activity, including in patients with the TKI resistance mutation T315I. The homoharringtonine derivative omacetaxine mepesuccinate, which inhibits protein synthesis, has also demonstrated clinical activity in CML, including in patients with TKI resistance due to T315I and in patients who have TKI resistance despite no evidence of ABL mutations. It is essential that clinicians implement these new agents with care and change therapies only when appropriate in order to preserve as many options as possible for future use if needed.

The Effect of Primer Application Modifications on the Bond Strength of 4th Generation Adhesive Bonding Agents

DTIC Science & Technology

2012-03-30

dentin. Methods: The coronal enamel of 120 extracted human third molars was removed with a low-speed saw. The teeth were mounted in PVC pipe with dental...LITERATURE REVIEW A. Background 1. Acid Etching in Dentistry. Buonocore demonstrated in 1955 that the preparation of dental enamel with an...The influence of deviations from the manufacturer’s instructions for the use of six adhesive systems on the bond strengths to enamel and dentin

Field observations of the electrostatic charges of blowing snow in Hokkaido, Japan

NASA Astrophysics Data System (ADS)

Omiya, S.; Sato, A.

2011-12-01

An electrostatic charge of blowing snow may be a contributing factor in the formation of a snow drift and a snow cornice, and changing of the trajectory of own motion. However, detailed electrification characteristics of blowing snow are not known as there are few reports of charge measurements. We carried out field observations of the electrostatic charges of blowing snow in Tobetsu, Hokkaido, Japan in the mid winter of 2011. An anemovane and a thermohygrometer were used for the meteorological observation. Charge-to-mass ratios of blowing snow were obtained by a Faraday-cage, an electrometer and an electric balance. In this observation period, the air temperature during the blowing snow event was -6.5 to -0.5 degree Celsius. The measured charges in this observation were consistent with the previous studies in sign, which is negative, but they were smaller than the previous one. In most cases, the measured values increased with the temperature decrease, which corresponds with previous studies. However, some results contradicted the tendency, and the maximum value was obtained on the day of the highest air temperature of -0.5 degree Celsius. This discrepancy may be explained from the difference of the snow surface condition on observation day. The day when the maximum value was obtained, the snow surface was covered with old snow, and hard. On the other hand, in many other cases, the snow surface was covered with the fresh snow, and soft. Blowing snow particles on the hard surface can travel longer distance than on the soft one. Therefore, it can be surmised that the hard surface makes the blowing snow particles accumulate a lot of negative charges due to a large number of collisions to the surface. This can be supported by the results of the wind tunnel experiments by Omiya and Sato (2011). By this field observation, it was newly suggested that the electrostatic charge of blowing snow are influenced greatly by the difference of the snow surface condition. REFERENCE: Omiya and Sato,(2010):An electrostatic charge measurement of blowing snow particles focusing on collision frequency to the snow surface. AGU Abstract Database, 2010 Fall Meeting.

Porous starch-based drug delivery systems processed by a microwave route.

PubMed

Malafaya, P B; Elvira, C; Gallardo, A; San Román, J; Reis, R L

2001-01-01

Abstract-A new simple processing route to produce starch-based porous materials was developed based on a microwave baking methodology. This innovative processing route was used to obtain non-loaded controls and loaded drug delivery carriers, incorporating a non-steroid anti-inflammatory agent. This bioactive agent was selected as model drug with expectations that the developed methodology might be used for other drugs and growth factors. The prepared systems were characterized by 1H and 13C NMR spectroscopy which allow the study of the interactions between the starch-based materials and the processing components, i.e, the blowing agents. The porosity of the prepared materials was estimated by measuring their apparent density and studied by comparing drug-loaded and non-loaded carriers. The behaviour of the porous structures, while immersed in aqueous media, was studied in terms of swelling and degradation, being intimately related to their porosity. Finally, in vitro drug release studies were performed showing a clear burst effect, followed by a slow controlled release of the drug over several days (up to 10 days).

On the Fraction of Quasars with Outflows

NASA Astrophysics Data System (ADS)

Ganguly, Rajib; Brotherton, Michael S.

2008-01-01

Outflows from active galactic nuclei (AGNs) seem to be common and are thought to be important from a variety of perspectives: as an agent of chemical enhancement of the interstellar and intergalactic media, as an agent of angular momentum removal from the accreting central engine, and as an agent limiting star formation in starbursting systems by blowing out gas and dust from the host galaxy. To understand these processes, we must determine what fraction of AGNs feature outflows and understand what forms they take. We examine recent surveys of quasar absorption lines, reviewing the best means to determine if systems are intrinsic and result from outflowing material, and the limitations of approaches taken to date. The surveys reveal that, while the fraction of specific forms of outflows depends on AGN properties, the overall fraction displaying outflows is fairly constant, approximately 60%, over many orders of magnitude in luminosity. We emphasize some issues concerning classification of outflows driven by data type rather than necessarily the physical nature of outflows and illustrate how understanding outflows probably requires a more comprehensive approach than has usually been taken in the past.

Thermal, Morphological and Rheological Properties of Rigid Polyurethane Foams as Thermal Insulating Materials

NASA Astrophysics Data System (ADS)

Kim, Ji Mun; Han, Mi Sun; Kim, Youn Hee; Kim, Woo Nyon

2008-07-01

The polyurethane foams (PUFs) were prepared by polyether polyols, polymeric 4,4'-diphenylmethane diisocyanate (PMDI), silicone surfactants, amine catalysts and cyclopentane as a blowing agent. Solid and liquid type fillers were used as a nucleating agent to decrease a cell size of the PUFs as well as improve the thermal insulating properties of the PUFs. The PUFs were prepared by adding solid and liquid type fillers in the range of 1 to 3 wt%. For the liquid type fillers, the cell size of the PUFs showed minimum and found to decrease compared the PUF without adding fillers. Also, thermal conductivity of the PUFs with adding fillers showed minimum. For the solid type fillers, cell size and thermal conductivity of the PUFs were observed to decrease with the filler content up to 3 wt%. From these results, it is suggested that the thermal insulating property of the PUFs can be improved by adding fillers as a nucleating agent. Also, storage and loss modulus of the PUFs will be presented to study gelling points of the PUFs.

Characteristics of Organizational Climate and Perceived Wrongdoing Associated with Whistle-Blowing Decisions.

ERIC Educational Resources Information Center

Miceli, Marcia P.; Near, Janet P.

1985-01-01

Employees of 15 organizations (N=8,600) completed questionnaires concerning whistle-blowing. Discriminant analysis revealed that organization members who had observed alleged wrongdoing were more likely to blow the whistle if they had convincing evidence of wrongdoing, if the wrongdoing were serious, and if it directly affected them. (Author/BL)

74. View of small steam tank used in 'blowing down' ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

74. View of small steam tank used in 'blowing down' or cleaning boilers; in background can be seen the bottom of cylindrical water tank located in setback at southeast corner of blowing engine house. - Sloss-Sheffield Steel & Iron, First Avenue North Viaduct at Thirty-second Street, Birmingham, Jefferson County, AL

Blowing Polymer Bubbles in an Acoustic Levitator

NASA Technical Reports Server (NTRS)

Lee, M. C.

1985-01-01

In new manufacturing process, small gas-filled polymer shells made by injecting gas directly into acoustically levitated prepolymer drops. New process allows sufficient time for precise control of shell geometry. Applications foreseen in fabrication of deuterium/tritium-filled fusion targets and in pharmaceutical coatings. New process also useful in glass blowing and blow molding.

A computational investigation of the finite-time blow-up of the 3D incompressible Euler equations based on the Voigt regularization

DOE PAGES

Larios, Adam; Petersen, Mark R.; Titi, Edriss S.; ...

2017-04-29

We report the results of a computational investigation of two blow-up criteria for the 3D incompressible Euler equations. One criterion was proven in a previous work, and a related criterion is proved here. These criteria are based on an inviscid regularization of the Euler equations known as the 3D Euler-Voigt equations, which are known to be globally well-posed. Moreover, simulations of the 3D Euler-Voigt equations also require less resolution than simulations of the 3D Euler equations for xed values of the regularization parameter α > 0. Therefore, the new blow-up criteria allow one to gain information about possible singularity formationmore » in the 3D Euler equations indirectly; namely, by simulating the better-behaved 3D Euler-Voigt equations. The new criteria are only known to be suficient for blow-up. Therefore, to test the robustness of the inviscid-regularization approach, we also investigate analogous criteria for blow-up of the 1D Burgers equation, where blow-up is well-known to occur.« less

Scattering and sequestering of blow-up moduli in local string models

NASA Astrophysics Data System (ADS)

Conlon, Joseph P.; Witkowski, Lukas T.

2011-12-01

We study the scattering and sequestering of blow-up fields - either local to or distant from a visible matter sector - through a CFT computation of the dependence of physical Yukawa couplings on the blow-up moduli. For a visible sector of D3-branes on orbifold singularities we compute the disk correlator left< {tau_s^{{(1)}}tau_s^{{(2)}}...tau_s^{{(n)}}ψ ψ φ } rightrangle between orbifold blow-up moduli and matter Yukawa couplings. For n = 1 we determine the full quantum and classical correlator. This result has the correct factorisation onto lower 3-point functions and also passes numerous other consistency checks. For n > 1 we show that the structure of picture-changing applied to the twist operators establishes the sequestering of distant blow-up moduli at disk level to all orders in α'. We explain how these results are relevant to suppressing soft terms to scales parametrically below the gravitino mass. By giving vevs to the blow-up fields we can move into the smooth limit and thereby derive CFT results for the smooth Swiss-cheese Calabi-Yaus that appear in the Large Volume Scenario.

A computational investigation of the finite-time blow-up of the 3D incompressible Euler equations based on the Voigt regularization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larios, Adam; Petersen, Mark R.; Titi, Edriss S.

We report the results of a computational investigation of two blow-up criteria for the 3D incompressible Euler equations. One criterion was proven in a previous work, and a related criterion is proved here. These criteria are based on an inviscid regularization of the Euler equations known as the 3D Euler-Voigt equations, which are known to be globally well-posed. Moreover, simulations of the 3D Euler-Voigt equations also require less resolution than simulations of the 3D Euler equations for xed values of the regularization parameter α > 0. Therefore, the new blow-up criteria allow one to gain information about possible singularity formationmore » in the 3D Euler equations indirectly; namely, by simulating the better-behaved 3D Euler-Voigt equations. The new criteria are only known to be suficient for blow-up. Therefore, to test the robustness of the inviscid-regularization approach, we also investigate analogous criteria for blow-up of the 1D Burgers equation, where blow-up is well-known to occur.« less

Improvement of maneuver aerodynamics by spanwise blowing

NASA Technical Reports Server (NTRS)

Erickson, G. E.; Campbell, J. F.

1977-01-01

Spanwise blowing was used to test a generalized wind-tunnel model to investigate component concepts in order to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on performance, stability, and control at high angles of attack and subsonic speeds. Test data were obtained in the Langley high speed 7 by 10 foot tunnel at free stream Mach numbers up to 0.50 for a range of model angles of attack, jet momentum coefficients, and leading and trailing edge flap deflection angles. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack.

Finite-time blow-up for quasilinear degenerate Keller-Segel systems of parabolic-parabolic type

NASA Astrophysics Data System (ADS)

Hashira, Takahiro; Ishida, Sachiko; Yokota, Tomomi

2018-05-01

This paper deals with the quasilinear degenerate Keller-Segel systems of parabolic-parabolic type in a ball of RN (N ≥ 2). In the case of non-degenerate diffusion, Cieślak-Stinner [3,4] proved that if q > m + 2/N, where m denotes the intensity of diffusion and q denotes the nonlinearity, then there exist initial data such that the corresponding solution blows up in finite time. As to the case of degenerate diffusion, it is known that a solution blows up if q > m + 2/N (see Ishida-Yokota [13]); however, whether the blow-up time is finite or infinite has been unknown. This paper gives an answer to the unsolved problem. Indeed, the finite-time blow-up of energy solutions is established when q > m + 2/N.

Agent Model Development for Assessing Climate-Induced Geopolitical Instability.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boslough, Mark B.; Backus, George A.

2005-12-01

We present the initial stages of development of new agent-based computational methods to generate and test hypotheses about linkages between environmental change and international instability. This report summarizes the first year's effort of an originally proposed three-year Laboratory Directed Research and Development (LDRD) project. The preliminary work focused on a set of simple agent-based models and benefited from lessons learned in previous related projects and case studies of human response to climate change and environmental scarcity. Our approach was to define a qualitative model using extremely simple cellular agent models akin to Lovelock's Daisyworld and Schelling's segregation model. Such modelsmore » do not require significant computing resources, and users can modify behavior rules to gain insights. One of the difficulties in agent-based modeling is finding the right balance between model simplicity and real-world representation. Our approach was to keep agent behaviors as simple as possible during the development stage (described herein) and to ground them with a realistic geospatial Earth system model in subsequent years. This work is directed toward incorporating projected climate data--including various C02 scenarios from the Intergovernmental Panel on Climate Change (IPCC) Third Assessment Report--and ultimately toward coupling a useful agent-based model to a general circulation model.3« less

Noise Benefits of Rotor Trailing Edge Blowing for a Model Turbofan

NASA Technical Reports Server (NTRS)

Woodward, Richard P.; Fite, E. Brian; Podboy, Gary G.

2007-01-01

An advanced model turbofan was tested in the NASA Glenn 9- by 15-Foot Low Speed Wind Tunnel (9x15 LSWT) to explore far field acoustic effects associated with rotor Trailing-Edge-Blowing (TEB) for a modern, 1.294 stage pressure ratio turbofan model. The TEB rotor (Fan9) was designed to be aerodynamically similar to the previously tested Fan1, and used the same stator and nacelle hardware. Fan9 was designed with trailing edge blowing slots using an external air supply directed through the rotor hub. The TEB flow was heated to approximate the average fan exit temperature at each fan test speed. Rotor root blockage inserts were used to block TEB to all but the outer 40 and 20% span in addition to full-span blowing. A configuration with full-span TEB on alternate rotor blades was also tested. Far field acoustic data were taken at takeoff/approach conditions at 0.10 tunnel Mach. Far-field acoustic results showed that full-span blowing near 2.0% of the total flow could reduce the overall sound power level by about 2 dB. This noise reduction was observed in both the rotor-stator interaction tones and for the spectral broadband noise levels. Blowing only the outer span region was not very effective for lowering noise, and actually increased the far field noise level in some instances. Full-span blowing of alternate blades at 1.0% of the overall flow rate (equivalent to full-span blowing of all blades at 2.0% flow) showed a more modest noise decrease relative to full-span blowing of all blades. Detailed hot film measurements of the TEB rotor wake at 2.0% flow showed that TEB was not every effective for filling in the wake defect at approach fan speed toward the tip region, but did result in overfilling the wake toward the hub. Downstream turbulence measurements supported this finding, and support the observed reduction in spectral broadband noise.

The new albumin-free recombinant factor VIII concentrates for treatment of hemophilia: do they represent an actual incremental improvement?

PubMed

Josephson, Cassandra D; Abshire, Thomas

2004-07-01

The goal of eliminating the low levels of infectious disease risk from hemophilia treatment has resulted in the development of multiple generations of recombinant factor VIII (rFVIII) products. The ideal product should be devoid of human and animal proteins, which may transmit infectious agents. These products should also maintain molecular integrity, hemostatic efficacy, similar immunogenicity, and acceptable side effect profiles as compared to plasma-derived factor VIII. Currently available first-, second-, and third-generation rFVIII products include Recombinate; Kogenate FS/Helixate FS and ReFacto; and Advate, respectively. During the evolution of rFVIII products, either full-length or B-domain-deleted factor VIII were transfected into immortalized cell lines. The B-domain-deleted product, ReFacto, has resulted in an additional method to monitor factor VIII levels. The third-generation products offer the theoretical advantage of being produced without human and/or animal proteins. Upon initial introduction into the marketplace, the newer products have a higher cost. However, when analyzing historical trends, the prices of these products are almost equivalent to first-generation products within 3 years of licensure. Thus, the initial cost of the product may be a minimal issue in the medical decision process when selecting rFVIII replacement therapy.

76 FR 58202 - TRICARE; TRICARE Sanction Authority for Third-Party Billing Agents

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-20

..., TRICARE Management Activity (TMA), or designee, with the authority to sanction third-party billing agents... instructions for submitting comments. Mail: Federal Docket Management System Office, 4800 Mark Center Drive.... Joy Saly, TRICARE Management Activity, Medical Benefits and Reimbursement Branch, telephone (303) 676...

Control of Flow Structure on Low Swept Delta Wing with Steady Leading Edge Blowing

NASA Astrophysics Data System (ADS)

Ozturk, Ilhan; Zharfa, Mohammadreza; Yavuz, Mehmet Metin

2014-11-01

Interest in unmanned combat air vehicles (UCAVs) and micro air vehicles (MAVs) has stimulated investigation of the flow structure, as well as its control, on delta wings having low and moderate values of sweep angle. In the present study, the flow structure is characterized on a delta wing of low sweep 35-degree angle, which is subjected to steady leading edge blowing. The techniques of laser illuminated smoke visualization, laser Doppler anemometry (LDA), and surface pressure measurements are employed to investigate the steady and unsteady nature of the flow structure on delta wing, in relation to the dimensionless magnitude of the blowing coefficient. Using statistics and spectral analysis, unsteadiness of the flow structure is studied in detail. Different injection locations are utilized to apply different blowing patterns in order to identify the most efficient control, which provides the upmost change in the flow structure with the minimum energy input. The study aims to find the optimum flow control strategy to delay or to prevent the stall and possibly to reduce the buffeting on the wing surface. Since the blowing set-up is computer controlled, the unsteady blowing patterns compared to the present steady blowing patterns will be studied next. This project was supported by the Scientific and Technological Research Council of Turkey (Project Number: 3501 111M732).

Morphology and viscoelastic properties of sealing materials based on EPDM rubber.

PubMed

Milić, J; Aroguz, A; Budinski-Simendić, J; Radicević, R; Prendzov, S

2008-12-01

In this applicative study, the ratio of active and inactive filler loadings was the prime factor for determining the dynamic-mechanical behaviour of ethylene-propylene-diene monomer rubbers. Scanning electron microscopy was used to study the structure of reinforced dense and microcellular elastomeric materials. The effects of filler and blowing agent content on the morphology of composites were investigated. Microcellular samples cured in salt bath show smaller cells and uniform cell size compared with samples cured in hot air. Dynamic-mechanical thermal analysis showed appreciable changes in the viscoelastic properties by increasing active filler content, which could enable tailoring the material properties to suit sealing applications.

Calibrator device for the extrusion of cable coatings

NASA Astrophysics Data System (ADS)

Garbacz, Tomasz; Dulebová, Ľudmila; Spišák, Emil; Dulebová, Martina

2016-05-01

This paper presents selected results of theoretical and experimental research works on a new calibration device (calibrators) used to produce coatings of electric cables. The aim of this study is to present design solution calibration equipment and present a new calibration machine, which is an important element of the modernized technology extrusion lines for coating cables. As a result of the extrusion process of PVC modified with blowing agents, an extrudate in the form of an electrical cable was obtained. The conditions of the extrusion process were properly selected, which made it possible to obtain a product with solid external surface and cellular core.

Method for providing a low density high strength polyurethane foam

DOEpatents

Whinnery, Jr., Leroy L.; Goods, Steven H.; Skala, Dawn M.; Henderson, Craig C.; Keifer, Patrick N.

2013-06-18

Disclosed is a method for making a polyurethane closed-cell foam material exhibiting a bulk density below 4 lbs/ft.sup.3 and high strength. The present embodiment uses the reaction product of a modified MDI and a sucrose/glycerine based polyether polyol resin wherein a small measured quantity of the polyol resin is "pre-reacted" with a larger quantity of the isocyanate in a defined ratio such that when the necessary remaining quantity of the polyol resin is added to the "pre-reacted" resin together with a tertiary amine catalyst and water as a blowing agent, the polymerization proceeds slowly enough to provide a stable foam body.

Shooting method for solution of boundary-layer flows with massive blowing

NASA Technical Reports Server (NTRS)

Liu, T.-M.; Nachtsheim, P. R.

1973-01-01

A modified, bidirectional shooting method is presented for solving boundary-layer equations under conditions of massive blowing. Unlike the conventional shooting method, which is unstable when the blowing rate increases, the proposed method avoids the unstable direction and is capable of solving complex boundary-layer problems involving mass and energy balance on the surface.

Speeding up social waves. Propagation mechanisms of shimmering in giant honeybees.

PubMed

Kastberger, Gerald; Hoetzl, Thomas; Maurer, Michael; Kranner, Ilse; Weiss, Sara; Weihmann, Frank

2014-01-01

Shimmering is a defence behaviour in giant honeybees (Apis dorsata), whereby bees on the nest surface flip their abdomen upwards in a Mexican wave-like process. However, information spreads faster than can be ascribed to bucket bridging, which is the transfer of information from one individual to an adjacent one. We identified a saltatoric process that speeds up shimmering by the generation of daughter waves, which subsequently merge with the parental wave, producing a new wave front. Motion patterns of individual "focus" bees (n = 10,894) and their shimmering-active neighbours (n = 459,558) were measured with high-resolution video recording and stereoscopic imaging. Three types of shimmering-active surface bees were distinguished by their communication status, termed "agents": "Bucket-bridging" agents comprised 74.98% of all agents, affected 88.17% of their neighbours, and transferred information at a velocity of v = 0.317±0.015 m/s. "Chain-tail" agents comprised 9.20% of the agents, were activated by 6.35% of their neighbours, but did not motivate others to participate in the wave. "Generator agents" comprised 15.82% of agents, showed abdominal flipping before the arrival of the main wave front, and initiated daughter waves. They affected 6.75% of their neighbourhood and speeded up the compound shimmering process compared to bucket bridging alone by 41.5% to v = 0.514±0.019 m/s. The main direction of shimmering was reinforced by 35.82% of agents, whereas the contribution of the complementing agents was fuzzy. We discuss that the saltatoric process could enable the bees to instantly recruit larger cohorts to participate in shimmering and to respond rapidly to changes in flight direction of preying wasps. A third, non-exclusive explanation is that at a distance of up to three metres from the nest the acceleration of shimmering could notably contribute to the startle response in mammals and birds.

Effect of evaporation of solvents from one-step, self-etching adhesives.

PubMed

Furuse, Adilson Yoshio; Peutzfeldt, Anne; Asmussen, Erik

2008-02-01

To investigate whether and to what extent the bonding capacity of one-step, self-etching adhesives is influenced by the degree to which solvent is evaporated. Seven one-step, self-etching adhesives were tested (Adper Prompt L-Pop, Clearfil S3 Bond, Futurabond NR, G-Bond, Hybrid Bond, iBond, Xeno III). The variation in degree of evaporation was obtained by varying the duration of the air-blowing step. The duration required to immobilize the adhesive layer, as established in a pilot study, was used as control. Two experimental air-blowing durations, shorter (half the control duration) and longer (double the control duration) than the control duration, were chosen. The resin composite Herculite XRV was bonded to flat human dentin surfaces treated with one of the adhesives following manufacturer's instructions, except for the air-blowing duration after application. After being stored in water at 37 degrees C for 1 week, the bonded specimens were broken in shear. Failure modes were evaluated under stereomicroscope. Air-blowing duration and brand of adhesive both had an effect on shear bond strength. An interaction was found between adhesive and air-blowing duration. Some adhesives were insensitive to variations in air-drying duration, but in general, air-blowing durations shorter than the control duration produced lower shear bond strengths. Significant effects of adhesive and air-blowing duration were also detected in relation to failure mode. More adhesive failures were observed with shorter air-blowing durations. A significant negative correlation between number of adhesive failures and bond strength was found. On the basis of this in vitro study, it may be concluded that the one-step, self-etching adhesives evaluated were sensitive to degree of evaporation of the solvents.

Blow Collection as a Non-Invasive Method for Measuring Cortisol in the Beluga (Delphinapterus leucas)

PubMed Central

Thompson, Laura A.; Spoon, Tracey R.; Goertz, Caroline E. C.; Hobbs, Roderick C.; Romano, Tracy A.

2014-01-01

Non-invasive sampling techniques are increasingly being used to monitor glucocorticoids, such as cortisol, as indicators of stressor load and fitness in zoo and wildlife conservation, research and medicine. For cetaceans, exhaled breath condensate (blow) provides a unique sampling matrix for such purposes. The purpose of this work was to develop an appropriate collection methodology and validate the use of a commercially available EIA for measuring cortisol in blow samples collected from belugas (Delphinapterus leucas). Nitex membrane stretched over a petri dish provided the optimal method for collecting blow. A commercially available cortisol EIA for measuring human cortisol (detection limit 35 pg ml−1) was adapted and validated for beluga cortisol using tests of parallelism, accuracy and recovery. Blow samples were collected from aquarium belugas during monthly health checks and during out of water examination, as well as from wild belugas. Two aquarium belugas showed increased blow cortisol between baseline samples and 30 minutes out of water (Baseline, 0.21 and 0.04 µg dl−1; 30 minutes, 0.95 and 0.14 µg dl−1). Six wild belugas also showed increases in blow cortisol between pre and post 1.5 hour examination (Pre 0.03, 0.23, 0.13, 0.19, 0.13, 0.04 µg dl−1, Post 0.60, 0.31, 0.36, 0.24, 0.14, 0.16 µg dl−1). Though this methodology needs further investigation, this study suggests that blow sampling is a good candidate for non-invasive monitoring of cortisol in belugas. It can be collected from both wild and aquarium animals efficiently for the purposes of health monitoring and research, and may ultimately be useful in obtaining data on wild populations, including endangered species, which are difficult to handle directly. PMID:25464121

Blow collection as a non-invasive method for measuring cortisol in the beluga (Delphinapterus leucas).

PubMed

Thompson, Laura A; Spoon, Tracey R; Goertz, Caroline E C; Hobbs, Roderick C; Romano, Tracy A

2014-01-01

Non-invasive sampling techniques are increasingly being used to monitor glucocorticoids, such as cortisol, as indicators of stressor load and fitness in zoo and wildlife conservation, research and medicine. For cetaceans, exhaled breath condensate (blow) provides a unique sampling matrix for such purposes. The purpose of this work was to develop an appropriate collection methodology and validate the use of a commercially available EIA for measuring cortisol in blow samples collected from belugas (Delphinapterus leucas). Nitex membrane stretched over a petri dish provided the optimal method for collecting blow. A commercially available cortisol EIA for measuring human cortisol (detection limit 35 pg ml-1) was adapted and validated for beluga cortisol using tests of parallelism, accuracy and recovery. Blow samples were collected from aquarium belugas during monthly health checks and during out of water examination, as well as from wild belugas. Two aquarium belugas showed increased blow cortisol between baseline samples and 30 minutes out of water (Baseline, 0.21 and 0.04 µg dl-1; 30 minutes, 0.95 and 0.14 µg dl-1). Six wild belugas also showed increases in blow cortisol between pre and post 1.5 hour examination (Pre 0.03, 0.23, 0.13, 0.19, 0.13, 0.04 µg dl-1, Post 0.60, 0.31, 0.36, 0.24, 0.14, 0.16 µg dl-1). Though this methodology needs further investigation, this study suggests that blow sampling is a good candidate for non-invasive monitoring of cortisol in belugas. It can be collected from both wild and aquarium animals efficiently for the purposes of health monitoring and research, and may ultimately be useful in obtaining data on wild populations, including endangered species, which are difficult to handle directly.

Similarity transformation for equilibrium boundary layers, including effects of blowing and suction

NASA Astrophysics Data System (ADS)

Chen, Xi; Hussain, Fazle

2017-03-01

We present a similarity transformation for the mean velocity profiles in sink flow turbulent boundary layers, including effects of blowing and suction. It is based on symmetry analysis which transforms the governing partial differential equations (for mean mass and momentum) into an ordinary differential equation and yields a new result including an exact, linear relation between the mean normal (V ) and streamwise (U ) velocities. A characteristic length function is further introduced which, under a first order expansion (whose coefficient is η ) in wall blowing and suction velocity, leads to the similarity transformation for U with the value of η ≈-1 /9 . This transformation is shown to be a group invariant and maps different U profiles under different blowing and suction conditions into a (universal) profile for no blowing or suction. Its inverse transformation enables predictions of all mean quantities in the mean mass and momentum equations, in good agreement with DNS data.

Visualization of airflow growing soap bubbles

NASA Astrophysics Data System (ADS)

Al Rahbi, Hamood; Bock, Matthew; Ryu, Sangjin

2016-11-01

Visualizing airflow inside growing soap bubbles can answer questions regarding the fluid dynamics of soap bubble blowing, which is a model system for flows with a gas-liquid-gas interface. Also, understanding the soap bubble blowing process is practical because it can contribute to controlling industrial processes similar to soap bubble blowing. In this study, we visualized airflow which grows soap bubbles using the smoke wire technique to understand how airflow blows soap bubbles. The soap bubble blower setup was built to mimic the human blowing process of soap bubbles, which consists of a blower, a nozzle and a bubble ring. The smoke wire was placed between the nozzle and the bubble ring, and smoke-visualized airflow was captured using a high speed camera. Our visualization shows how air jet flows into the growing soap bubble on the ring and how the airflow interacts with the soap film of growing bubble.

Experimental parametric study of jet vortex generators for flow separation control

NASA Technical Reports Server (NTRS)

Selby, Gregory

1991-01-01

A parametric wind-tunnel study was performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low-speed turbulence flow over a two-dimensional rearward-facing ramp. Results indicate that flow-separation control can be accomplished, with the level of control achieved being a function of jet speed, jet orientation (with respect to the free-stream direction), and orifice pattern (double row of jets vs. single row). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed). Dye flow visualization tests in a water tunnel indicated that the most effective jet vortex generator configurations produced streamwise co-rotating vortices.

Pore Size Control in Aluminium Foam by Standardizing Bubble Rise Velocity and Melt Viscosity

NASA Astrophysics Data System (ADS)

Avinash, G.; Harika, V.; Sandeepika, Ch; Gupta, N.

2018-03-01

In recent years, aluminium foams have found use in a wide range of applications. The properties of these foams, as good structural strength with light weight have made them as a promising structural material for aerospace industry. Foaming techniques (direct and indirect) are used to produce these foams. Direct foaming involves blowing of gas to create gas bubbles in the melt whereas indirect foaming technique uses blowing agents as metallic hydrides, which create hydrogen bubbles. Porosity and its distribution in foams directly affect its properties. This demands for more theoretical studies, to control such cellular structure and hence properties. In present work, we have studied the effect of gas bubble rise velocity and melt viscosity, on pore size and its distribution in aluminium foam. A 15 PPI aluminium foam, prepared using indirect foaming technique having porosity ~86 % was used for study. In order to obtain metal foam, the bubble must not escape from the melt and should get entrapped during solidification. Our calculations suggest that bubble rise velocity and melt viscosity are responsible for vertical displacement of bubble in the melt. It is observed that melt viscosity opposes bubble rise velocity and help the bubbles to stay in the melt, resulting in porous structure.

Modeling Radicalization Phenomena in Heterogeneous Populations.

PubMed

Galam, Serge; Javarone, Marco Alberto

2016-01-01

The phenomenon of radicalization is investigated within a mixed population composed of core and sensitive subpopulations. The latest includes first to third generation immigrants. Respective ways of life may be partially incompatible. In case of a conflict core agents behave as inflexible about the issue. In contrast, sensitive agents can decide either to live peacefully adjusting their way of life to the core one, or to oppose it with eventually joining violent activities. The interplay dynamics between peaceful and opponent sensitive agents is driven by pairwise interactions. These interactions occur both within the sensitive population and by mixing with core agents. The update process is monitored using a Lotka-Volterra-like Ordinary Differential Equation. Given an initial tiny minority of opponents that coexist with both inflexible and peaceful agents, we investigate implications on the emergence of radicalization. Opponents try to turn peaceful agents to opponents driving radicalization. However, inflexible core agents may step in to bring back opponents to a peaceful choice thus weakening the phenomenon. The required minimum individual core involvement to actually curb radicalization is calculated. It is found to be a function of both the majority or minority status of the sensitive subpopulation with respect to the core subpopulation and the degree of activeness of opponents. The results highlight the instrumental role core agents can have to hinder radicalization within the sensitive subpopulation. Some hints are outlined to favor novel public policies towards social integration.

Modeling Radicalization Phenomena in Heterogeneous Populations

PubMed Central

2016-01-01

The phenomenon of radicalization is investigated within a mixed population composed of core and sensitive subpopulations. The latest includes first to third generation immigrants. Respective ways of life may be partially incompatible. In case of a conflict core agents behave as inflexible about the issue. In contrast, sensitive agents can decide either to live peacefully adjusting their way of life to the core one, or to oppose it with eventually joining violent activities. The interplay dynamics between peaceful and opponent sensitive agents is driven by pairwise interactions. These interactions occur both within the sensitive population and by mixing with core agents. The update process is monitored using a Lotka-Volterra-like Ordinary Differential Equation. Given an initial tiny minority of opponents that coexist with both inflexible and peaceful agents, we investigate implications on the emergence of radicalization. Opponents try to turn peaceful agents to opponents driving radicalization. However, inflexible core agents may step in to bring back opponents to a peaceful choice thus weakening the phenomenon. The required minimum individual core involvement to actually curb radicalization is calculated. It is found to be a function of both the majority or minority status of the sensitive subpopulation with respect to the core subpopulation and the degree of activeness of opponents. The results highlight the instrumental role core agents can have to hinder radicalization within the sensitive subpopulation. Some hints are outlined to favor novel public policies towards social integration. PMID:27166677

Field patterns without blow up

NASA Astrophysics Data System (ADS)

Mattei, Ornella; Milton, Graeme W.

2017-09-01

Field patterns, first proposed by the authors in Milton and Mattei (2017 Proc. R. Soc. A 473 20160819), are a new type of wave propagating along orderly patterns of characteristic lines which arise in specific space-time microstructures whose geometry in one spatial dimension plus time is somehow commensurate with the slope of the characteristic lines. In particular, in Milton and Mattei (2017 Proc. R. Soc. A 473 20160819) the authors propose two examples of space-time geometries in which field patterns occur: they are two-phase microstructures in which rectangular space-time inclusions of one material are embedded in another material. After a sufficiently long interval of time, field patterns have local periodicity both in time and space. This allows one to focus only on solving the problem on the discrete network on which a field pattern lives and to define a suitable transfer matrix that, given the solution at a certain time, provides the solution after one time period. For the aforementioned microstructures, many of the eigenvalues of this { P }{ T }-symmetric transfer matrix have unit norm and hence the corresponding eigenvectors correspond to propagating modes. However, there are also modes that blow up exponentially with time coupled with modes that decrease exponentially with time. The question arises as to whether there are space-time microstructures such that the transfer matrix only has eigenvalues on the unit circle, so that there are no growing modes (modes that blow-up)? The answer is found here, where we see that certain space-time checkerboards have the property that all the modes are propagating modes, within a certain range of the material parameters. Interestingly, when there is no blow-up, the waves generated by an instantaneous disturbance at a point look like shocks with a wake of oscillatory waves, whose amplitude, very remarkably, does not tend to zero away from the wave front.

Near-Surface Geophysical Imaging of Deformation Associated with the Daytona Beach Sand Blow Deposits, Lee County, Arkansas

NASA Astrophysics Data System (ADS)

Rohrer, M.; Harris, J. B.; Cearley, C.; Teague, M.

2017-12-01

Within the past decade or so, paleoseismologic and geophysical studies at the Daytona Beach (DB) site in east-central Arkansas have reported earthquake-induced liquefaction (sand blows) along a prominent NW-trending lineament dated to approximately 5.5 ka. A recent compressional-wave (P-wave) seismic reflection survey acquired by the U. S. Geological Survey (USGS) along Highway 243 in Lee County, Arkansas, across the DB sand blow cluster, identified a previously unknown fault zone that is likely associated with the liquefaction. However, the USGS data were not able to image the Quaternary section (<60 m deep) and show a direct connection between the deeper faulting and the sand blows. In order to investigate the near-surface structure of the fault zone, we acquired an integrated geophysical data set consisting of 430-m-long shear-wave (S-wave) seismic reflection and ground penetrating radar (GPR) profiles above the deformation imaged on the USGS profile. The S-wave reflection data were collected using a 24-channel, towable landstreamer and the seismic energy was generated by a sledgehammer/I-beam source. The GPR data were collected with a cart-mounted 250-MHz system, using a 0.5-m antenna spacing and a 0.10-m step size. The processed seismic profile exhibits coherent reflection energy throughout the Quaternary section. Changes in reflection amplitude and coherency, offset reflections, and abundant diffractions suggest the presence of a complex zone of high-angle faults in the shallow subsurface coincident with the mapped lineament. Folded shallow reflections show that the deformation extends upward to within 10 m of the surface. Furthermore, the GPR profile images a distinct zone of deformation in the very near surface (<1.5 m deep) that is coincident with the upward projection of the deformation imaged on the S-wave seismic reflection profile.

Flap noise measurements for STOL configurations using external upper surface blowing

NASA Technical Reports Server (NTRS)

Dorsch, R. G.; Reshotko, M.; Olsen, W. A.

1972-01-01

Screening tests of upper surface blowing on externally blown flaps configurations were conducted. Noise and turning effectiveness data were obtained with small-scale, engine-over-the-wing models. One large model was tested to determine scale effects. Nozzle types included circular, slot, D-shaped, and multilobed. Tests were made with and without flow attachment devices. For STOL applications the particular multilobed mixer and the D-shaped nozzles tested were found to offer little or no noise advantage over the round convergent nozzle. High aspect ratio slot nozzles provided the quietest configurations. In general, upper surface blowing was quieter than lower surface blowing for equivalent EBF models.

Free-flight investigation of forebody blowing for stability and control

NASA Technical Reports Server (NTRS)

Brandon, Jay M.; Simon, James M.; Owens, D. Bruce; Kiddy, Jason S.

1996-01-01

A free-flight wind-tunnel investigation was conducted on a generic fighter model with forebody pneumatic vortex control for high angle-of-attack directional control. This is believed to be the first flight demonstration of a forebody blowing concept integrated into a closed-loop flight control system for stability augmentation and control. The investigation showed that the static wind tunnel estimates of the yaw control available generally agreed with flight results. The control scheme for the blowing nozzles consisted of an on/off control with a deadband. Controlled flight was obtained for the model using forebody blowing for directional control to beyond 45 deg. angle of attack.

Local-in-space blow-up criteria for a class of nonlinear dispersive wave equations

NASA Astrophysics Data System (ADS)

Novruzov, Emil

2017-11-01

This paper is concerned with blow-up phenomena for the nonlinear dispersive wave equation on the real line, ut -uxxt +[ f (u) ] x -[ f (u) ] xxx +[ g (u) + f″/(u) 2 ux2 ] x = 0 that includes the Camassa-Holm equation as well as the hyperelastic-rod wave equation (f (u) = ku2 / 2 and g (u) = (3 - k) u2 / 2) as special cases. We establish some a local-in-space blow-up criterion (i.e., a criterion involving only the properties of the data u0 in a neighborhood of a single point) simplifying and precising earlier blow-up criteria for this equation.

Global existence and finite time blow-up for a class of thin-film equation

NASA Astrophysics Data System (ADS)

Dong, Zhihua; Zhou, Jun

2017-08-01

This paper deals with a class of thin-film equation, which was considered in Li et al. (Nonlinear Anal Theory Methods Appl 147:96-109, 2016), where the case of lower initial energy (J(u_0)≤ d and d is a positive constant) was discussed, and the conditions on global existence or blow-up are given. We extend the results of this paper on two aspects: Firstly, we consider the upper and lower bounds of blow-up time and asymptotic behavior when J(u_0)d.

Helical instability in film blowing process: Analogy to buckling instability

NASA Astrophysics Data System (ADS)

Lee, Joo Sung; Kwon, Ilyoung; Jung, Hyun Wook; Hyun, Jae Chun

2017-12-01

The film blowing process is one of the most important polymer processing operations, widely used for producing bi-axially oriented film products in a single-step process. Among the instabilities observed in this film blowing process, i.e., draw resonance and helical motion occurring on the inflated film bubble, the helical instability is a unique phenomenon portraying the snake-like undulation motion of the bubble, having the period on the order of few seconds. This helical instability in the film blowing process is commonly found at the process conditions of a high blow-up ratio with too low a freezeline position and/or too high extrusion temperature. In this study, employing an analogy to the buckling instability for falling viscous threads, the compressive force caused by the pressure difference between inside and outside of the film bubble is introduced into the simulation model along with the scaling law derived from the force balance between viscous force and centripetal force of the film bubble. The simulation using this model reveals a close agreement with the experimental results of the film blowing process of polyethylene polymers such as low density polyethylene and linear low density polyethylene.

Dynamic Modeling of the Main Blow in Basic Oxygen Steelmaking Using Measured Step Responses

NASA Astrophysics Data System (ADS)

Kattenbelt, Carolien; Roffel, B.

2008-10-01

In the control and optimization of basic oxygen steelmaking, it is important to have an understanding of the influence of control variables on the process. However, important process variables such as the composition of the steel and slag cannot be measured continuously. The decarburization rate and the accumulation rate of oxygen, which can be derived from the generally measured waste gas flow and composition, are an indication of changes in steel and slag composition. The influence of the control variables on the decarburization rate and the accumulation rate of oxygen can best be determined in the main blow period. In this article, the measured step responses of the decarburization rate and the accumulation rate of oxygen to step changes in the oxygen blowing rate, lance height, and the addition rate of iron ore during the main blow are presented. These measured step responses are subsequently used to develop a dynamic model for the main blow. The model consists of an iron oxide and a carbon balance and an additional equation describing the influence of the lance height and the oxygen blowing rate on the decarburization rate. With this simple dynamic model, the measured step responses can be explained satisfactorily.

Proteus mirabilis interkingdom swarming signals attract blow flies

PubMed Central

Ma, Qun; Fonseca, Alicia; Liu, Wenqi; Fields, Andrew T; Pimsler, Meaghan L; Spindola, Aline F; Tarone, Aaron M; Crippen, Tawni L; Tomberlin, Jeffery K; Wood, Thomas K

2012-01-01

Flies transport specific bacteria with their larvae that provide a wider range of nutrients for those bacteria. Our hypothesis was that this symbiotic interaction may depend on interkingdom signaling. We obtained Proteus mirabilis from the salivary glands of the blow fly Lucilia sericata; this strain swarmed significantly and produced a strong odor that attracts blow flies. To identify the putative interkingdom signals for the bacterium and flies, we reasoned that as swarming is used by this bacterium to cover the food resource and requires bacterial signaling, the same bacterial signals used for swarming may be used to communicate with blow flies. Using transposon mutagenesis, we identified six novel genes for swarming (ureR, fis, hybG, zapB, fadE and PROSTU_03490), then, confirming our hypothesis, we discovered that fly attractants, lactic acid, phenol, NaOH, KOH and ammonia, restore swarming for cells with the swarming mutations. Hence, compounds produced by the bacterium that attract flies also are utilized for swarming. In addition, bacteria with the swarming mutation rfaL attracted fewer blow flies and reduced the number of eggs laid by the flies. Therefore, we have identified several interkingdom signals between P. mirabilis and blow flies. PMID:22237540

The effects of local blowing perturbations on thermal turbulent structures

NASA Astrophysics Data System (ADS)

Liu, Can; Araya, Guillermo; Leonardi, Stefano; Castillo, Luciano

2013-11-01

Blowing is an active flow control technique with several industrial applications, particularly in film cooling of turbine blades. In the past, the effects of localized blowing have been mostly analyzed on the velocity field and its influence of the flow parameters and turbulence structures (Krogstad and Kourakine, 2000). However, little literature can be found on the effects of blowing on the coherent thermal structures. In the present study, an incompressible turbulent channel flow with given steady blowing at the wall is simulated via DNS by means of five spanwise holes. The Reynolds number based on the friction velocity and half channel height is approximately Re = 394 and the molecular Prandtl number is Pr = 0.71. Temperature is considered a passive scalar with isothermal conditions at the wall. Different blowing amplitudes and perturbing angles (with respect to the streamwise direction) are applied to find out their effects on the turbulent thermal structures by means of a two-point correlation analysis. In addition, local reduction and increase of drag are connected to vorticity. The corresponding influence of perturbing amplitudes and angles on the energy budget of thermal fluctuations and turbulent Prandtl numbers are also shown and discussed.

Numerical study of delta wing leading edge blowing

NASA Technical Reports Server (NTRS)

Yeh, David; Tavella, Domingo; Roberts, Leonard

1988-01-01

Spanwise and tangential leading edge blowing as a means of controlling the position and strength of the leading edge vortices are studied by numerical solution of the three-dimensional Navier-Stokes equations. The leading edge jet is simulated by defining a permeable boundary, corresponding to the jet slot, where suitable boundary conditions are implemented. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of spanwise leading edge blowing at moderate angle of attack magnifies the size and strength of the leading edge vortices, and moves the vortex cores outboard and upward. The increase in lift primarily comes from the greater nonlinear vortex lift. However, spanwise blowing causes earlier vortex breakdown, thus decreasing the stall angle. The effects of tangential blowing at low to moderate angles of attack tend to reduce the pressure peaks associated with leading edge vortices and to increase the suction peak around the leading edge, so that the integrated value of the surface pressure remains about the same. Tangential leading edge blowing in post-stall conditions is shown to re-establish vortical flow and delay vortex bursting, thus increasing C sub L sub max and stall angle.

Prospects and challenges of developing new agents for tough Gram-negatives.

PubMed

Meyer, Annette L

2005-10-01

Historically, the medical profession has been successful in treating most bacterial infections in humans with synthetic second- and third-generation antibiotics. Recently, the prospects for continued success have dimmed with the increase in multidrug-resistant stains of bacteria. Infections caused by the Gram-negative bacteria Pseudomonas aeruginosa and Acinetobacter spp. in particular have increased in frequency and severity, and become progressively more difficult to treat. Contributors to disease severity include chronic infections due to mutator strains, persister cells and biofilms. The worst-case scenario of infections susceptible only to toxic polymixins is now a reality. The need to address the treatment of multidrug-resistant pathogens with innovative combination approaches and/or novel antibacterial agents is occurring in the context of reduced investment in antimicrobial drug discovery by the pharmaceutical industry.

Gadolinium-labeled dendronized gold nanoparticles as new targeted MRI contrast agent

NASA Astrophysics Data System (ADS)

Pan, Hongmu; Daniel, Marie-Christine

2010-04-01

Early diagnosis is critical for positive outcome of cancer treatments. In many cases, lives would be saved if the tumor could be detected at a very early stage. Nanoparticles have the property of passively targeting tumor sites due to their enhanced permeation and retention (EPR) effect. Thus they can play a critical role in improving the ability to find cancer in its earliest and most treatable stages. Furthermore magnetic resonance imaging is one of the most precise techniques for cancer screening since it can show 3D images of the tumors. For a better enhancement of the sensitivity of this method, MRI contrast agent (DOTA)Gd was attached to poly(propylene imine) dendrons of third generation and the obtained dendrons were used for modification of gold nanoparticles.

Sales of veterinary antimicrobial agents for therapeutic use in food-producing animal species in Japan between 2005 and 2010.

PubMed

Hosoi, Y; Asai, T; Koike, R; Tsuyuki, M; Sugiura, K

2014-12-01

The use of veterinary antimicrobial agents in animals can result in the emergence and selection of resistant bacteria in food-producing animals. This study elucidated the use of veterinary antimicrobial agents in Japan in terms of milligrams of active ingredient sold per kilogram of biomass between 2005 and 2010. Data on sales of antimicrobial agents and on the biomass of the target animal species were compiled from statistics published bythe Japanese Ministry of Agriculture, Forestry and Fisheries. The quantities of antimicrobials used varied between animal species: the highest usage was observed in pigs (392 to 423 mg/ kg), followed by beef cattle (45 to 67 mg/kg), broiler chickens (44 to 63 mg/kg) and dairy cattle (33 to 49 mg/kg). For the animal species combined, usage of third- and fourth-generation cefalosporins, fluoroquinolones and macrolides ranged from 0.10 to 0.14 mg/kg biomass, 1.1 to 1.3 mg/kg biomass and 7.8 to 10.6 mg/kg biomass, respectively.

Description of third instars of Cochliomyia minima (Diptera: Calliphoridae) from West Indies, and updated identification key.

PubMed

Yusseff-Vanegas, S

2014-09-01

The blow fly Cochliomyia minima Shannon is endemic to the Caribbean, and it has great potential for forensic applications because of its abundance and broad distribution in the region. However, its larval stages are unknown. Here, I update previously published identification keys by describing for the first time the morphology of C. minima larvae. The larvae of C. minima are found to be very similar to those of Cochliomyia macellaria F., but the former can be easily identified by the oral sclerite completely pigmented, visible as a spike between mouth hooks. The description of C. minima larvae in this study will be useful to forensic scientists in the Caribbean region.

Aerodynamic control of NASP-type vehicles through Vortex manipulation. Volume 2: Static wind tunnel tests

NASA Technical Reports Server (NTRS)

Suarez, Carlos J.; Kramer, Brian R.; Smith, Brooke C.; Malcolm, Gerald N.

1993-01-01

Forebody Vortex Control (FVC) was explored in this research program for potential application to a NASP-type configuration. Wind tunnel tests were conducted to evaluate a number of jet blowing schemes. The configuration tested has a slender forebody and a 78 deg swept delta wing. Blowing jets were implemented on the leeward side of the forebody with small circular tubes tangential to the surface that could be directed aft, forward, or at angles in between. The effects of blowing are observed primarily in the yawing and rolling moments and are highly dependent on the jet configuration and the angle of attack. Results show that the baseline flow field, without blowing activated, is quite sensitive to the geometry differences of the various protruding jets, as well as being sensitive to the blowing, particularly in the angle of attack range where the forebody vortices are naturally asymmetric. The time lag of the flow field response to the initiation of blowing was also measured. The time response was very short, on the order of the time required for the flow disturbance to travel the distance from the nozzle to the specific airframe location of interest at the free stream velocity. Overall, results indicate that sizable yawing and rolling moments can be induced with modest blowing levels. However, direct application of this technique on a very slender forebody would require thorough wind tunnel testing to optimize the jet location and configuration.

Stagnation region gas film cooling: Spanwise angled injection from multiple rows of holes. [gas turbine engines

NASA Technical Reports Server (NTRS)

Luckey, D. W.; Lecuyer, M. R.

1981-01-01

The stagnation region of a cylinder in a cross flow was used in experiments conducted with both a single row and multiple rows of spanwise angled (25 deg) coolant holes for a range of the coolant blowing ratio with a freestream to wall temperature ratio approximately equal to 1.7 and R(eD) = 90,000. Data from local heat flux measurements are presented for injection from a single row located at 5 deg, 22.9 deg, 40.8 deg, 58.7 deg from stagnation using a hole spacing ratio of S/d(o) = 5 and 10. Three multiple row configurations were also investigated. Data are presented for a uniform blowing distribution and for a nonuniform blowing distribution simulating a plenum supply. The data for local Stanton Number reduction demonstrated a lack of lateral spreading by the coolant jets. Heat flux levels larger than those without film cooling were observed directly behind the coolant holes as the blowing ratio exceeded a particular value. The data were spanwise averaged to illustrate the influence of injection location, blowing ratio and hole spacing. The large values of blowing ratio for the blowing distribution simulating a plenum supply resulted in heat flux levels behind the holes in excess of the values without film cooling. An increase in freestream turbulence intensity from 4.4 to 9.5 percent had a negligible effect on the film cooling performance.

Technological Innovations of Carbon Dioxide Injection in EAF-LF Steelmaking

NASA Astrophysics Data System (ADS)

Wei, Guangsheng; Zhu, Rong; Wu, Xuetao; Dong, Kai; Yang, Lingzhi; Liu, Runzao

2018-06-01

In this study, the recent innovations and improvements in carbon dioxide (CO2) injection technologies for electric arc furnace (EAF)-ladle furnace (LF) steelmaking processes have been reviewed. The utilization of CO2 in the EAF-LF steelmaking process resulted in improved efficiency, purity and environmental impact. For example, coherent jets with CO2 and O2 mixed injection can reduce the amount of iron loss and dust generation, and submerged O2 and powder injection with CO2 in an EAF can increase the production efficiency and improve the dephosphorization and denitrification characteristics. Additionally, bottom-blowing CO2 in an EAF can strengthen molten bath stirring and improve nitrogen removal, while bottom-blowing CO2 in a LF can increase the rate of desulfurization and improve the removal of inclusions. Based on these innovations, a prospective process for the cyclic utilization of CO2 in the EAF-LF steelmaking process is introduced that is effective in mitigating greenhouse gas emissions from the steelmaking shop.

Generating Soap Bubbles by Blowing on Soap Films

NASA Astrophysics Data System (ADS)

Salkin, Louis; Schmit, Alexandre; Panizza, Pascal; Courbin, Laurent

2016-02-01

Making soap bubbles by blowing air on a soap film is an enjoyable activity, yet a poorly understood phenomenon. Working either with circular bubble wands or long-lived vertical soap films having an adjustable steady state thickness, we investigate the formation of such bubbles when a gas is blown through a nozzle onto a film. We vary film size, nozzle radius, space between the film and nozzle, and gas density, and we measure the gas velocity threshold above which bubbles are formed. The response is sensitive to containment, i.e., the ratio between film and jet sizes, and dissipation in the turbulent gas jet, which is a function of the distance from the film to the nozzle. We rationalize the observed four different regimes by comparing the dynamic pressure exerted by the jet on the film and the Laplace pressure needed to create the curved surface of a bubble. This simple model allows us to account for the interplay between hydrodynamic, physicochemical, and geometrical factors.

The damaging punch.

PubMed Central

Atha, J; Yeadon, M R; Sandover, J; Parsons, K C

1985-01-01

The mechanical properties of a boxing punch have been determined using several techniques. The results are consistent with the medical consequences of boxing discussed in the report of the Board of Science and Education Working Party on boxing. Data were gathered from a world ranked British professional heavyweight, Frank Bruno, as he punched an instrumented, padded target mass suspended as a ballistic pendulum. Within 0.1 s of the start the punch had travelled 0.49 m and attained a velocity on impact of 8.9 m/s. The peak force on impact of 4096N (0.4 ton), attained within 14 ms of contact, represents a blow to the human head of up to 6320N (0.63 ton). The transmitted impulse generated an acceleration of 520 m/s2 (53 g) in the target head. For comparison an equivalent blow would be delivered by a padded wooden mallet with a mass of 6 kg (13 lbs) if swung at 20 mph. Images FIG 1 FIG 2 PMID:3936571

Technological Innovations of Carbon Dioxide Injection in EAF-LF Steelmaking

NASA Astrophysics Data System (ADS)

Wei, Guangsheng; Zhu, Rong; Wu, Xuetao; Dong, Kai; Yang, Lingzhi; Liu, Runzao

2018-03-01

In this study, the recent innovations and improvements in carbon dioxide (CO2) injection technologies for electric arc furnace (EAF)-ladle furnace (LF) steelmaking processes have been reviewed. The utilization of CO2 in the EAF-LF steelmaking process resulted in improved efficiency, purity and environmental impact. For example, coherent jets with CO2 and O2 mixed injection can reduce the amount of iron loss and dust generation, and submerged O2 and powder injection with CO2 in an EAF can increase the production efficiency and improve the dephosphorization and denitrification characteristics. Additionally, bottom-blowing CO2 in an EAF can strengthen molten bath stirring and improve nitrogen removal, while bottom-blowing CO2 in a LF can increase the rate of desulfurization and improve the removal of inclusions. Based on these innovations, a prospective process for the cyclic utilization of CO2 in the EAF-LF steelmaking process is introduced that is effective in mitigating greenhouse gas emissions from the steelmaking shop.

Generating Soap Bubbles by Blowing on Soap Films.

PubMed

Salkin, Louis; Schmit, Alexandre; Panizza, Pascal; Courbin, Laurent

2016-02-19

Making soap bubbles by blowing air on a soap film is an enjoyable activity, yet a poorly understood phenomenon. Working either with circular bubble wands or long-lived vertical soap films having an adjustable steady state thickness, we investigate the formation of such bubbles when a gas is blown through a nozzle onto a film. We vary film size, nozzle radius, space between the film and nozzle, and gas density, and we measure the gas velocity threshold above which bubbles are formed. The response is sensitive to containment, i.e., the ratio between film and jet sizes, and dissipation in the turbulent gas jet, which is a function of the distance from the film to the nozzle. We rationalize the observed four different regimes by comparing the dynamic pressure exerted by the jet on the film and the Laplace pressure needed to create the curved surface of a bubble. This simple model allows us to account for the interplay between hydrodynamic, physicochemical, and geometrical factors.

Class act: safety comparison of approved tyrosine kinase inhibitors for non-small-cell lung carcinoma.

PubMed

Burotto, Mauricio; Ali, Syed Abbas; O'Sullivan Coyne, Geraldine

2015-01-01

The past decade has seen the development and widespread use of tyrosine kinase inhibitors (TKIs) targeting a mutated EGFR (mEGFR) for the treatment of metastatic NSCLC. We discuss the main properties of the TKIs currently recommended for the treatment of mEGFR NSCLC: gefitinib, erlotinib and afatinib. The mechanism of action, pharmacodynamics and pharmacokinetics of these drugs, with emphasis on the historical context of their preclinical and clinical development, will be covered, including potential resistance mechanisms to these first-generation TKIs that has driven the trial design for second and third generations of EGFR inhibitors. Six Phase III clinical trials comparing these three TKIs with cisplatin-based chemotherapy upfront for mEGFR NSCLC provide the basis for the comparative safety and toxicity analysis between these agents. Class-related toxicity of these EGFR inhibitors, including life-threatening effects, will be discussed. Toxicity and safety analysis from the Phase III trials of these agents in mEGFR populations suggests that afatinib has more frequent and severe side effects. Given that an efficacy advantage has not yet been demonstrated for afatinib over erlotinib and gefitinib, the consistent class toxicity profile of these agents means that gefitinib and erlotinib are a safer first-line treatment recommendation.

Kit for detecting nucleic acid sequences using competitive hybridization probes

DOEpatents

Lucas, Joe N.; Straume, Tore; Bogen, Kenneth T.

2001-01-01

A kit is provided for detecting a target nucleic acid sequence in a sample, the kit comprising: a first hybridization probe which includes a nucleic acid sequence that is sufficiently complementary to selectively hybridize to a first portion of the target sequence, the first hybridization probe including a first complexing agent for forming a binding pair with a second complexing agent; and a second hybridization probe which includes a nucleic acid sequence that is sufficiently complementary to selectively hybridize to a second portion of the target sequence to which the first hybridization probe does not selectively hybridize, the second hybridization probe including a detectable marker; a third hybridization probe which includes a nucleic acid sequence that is sufficiently complementary to selectively hybridize to a first portion of the target sequence, the third hybridization probe including the same detectable marker as the second hybridization probe; and a fourth hybridization probe which includes a nucleic acid sequence that is sufficiently complementary to selectively hybridize to a second portion of the target sequence to which the third hybridization probe does not selectively hybridize, the fourth hybridization probe including the first complexing agent for forming a binding pair with the second complexing agent; wherein the first and second hybridization probes are capable of simultaneously hybridizing to the target sequence and the third and fourth hybridization probes are capable of simultaneously hybridizing to the target sequence, the detectable marker is not present on the first or fourth hybridization probes and the first, second, third, and fourth hybridization probes each include a competitive nucleic acid sequence which is sufficiently complementary to a third portion of the target sequence that the competitive sequences of the first, second, third, and fourth hybridization probes compete with each other to hybridize to the third portion of the target sequence.

Blowing-Type Boundary-Layer Control as Applied to the Trailing-Edge Flaps of a 35 Degree Swept-Wing Airplane

NASA Technical Reports Server (NTRS)

Kelly, Mark W; Anderson, Seth B; Innis, Robert C

1958-01-01

A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying blowing-type boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effects of boundary-layer control on the handling qualities and operation of the airplane, particularly during landing and take-off. The wind-tunnel and flight tests indicated that blowing over the flaps produced large increases in flap lift increment, and significant increases in maximum lift. The use of blowing permitted reductions in the landing approach speeds of as much as 12 knots.

Mathematical model of whole-process calculation for bottom-blowing copper smelting

NASA Astrophysics Data System (ADS)

Li, Ming-zhou; Zhou, Jie-min; Tong, Chang-ren; Zhang, Wen-hai; Li, He-song

2017-11-01

The distribution law of materials in smelting products is key to cost accounting and contaminant control. Regardless, the distribution law is difficult to determine quickly and accurately by mere sampling and analysis. Mathematical models for material and heat balance in bottom-blowing smelting, converting, anode furnace refining, and electrolytic refining were established based on the principles of material (element) conservation, energy conservation, and control index constraint in copper bottom-blowing smelting. Simulation of the entire process of bottom-blowing copper smelting was established using a self-developed MetCal software platform. A whole-process simulation for an enterprise in China was then conducted. Results indicated that the quantity and composition information of unknown materials, as well as heat balance information, can be quickly calculated using the model. Comparison of production data revealed that the model can basically reflect the distribution law of the materials in bottom-blowing copper smelting. This finding provides theoretical guidance for mastering the performance of the entire process.

A feasible method to eliminate nanoleakage in dentin hybrid layers.

PubMed

Chen, Ji-Hua; Liu, Yan; Niu, Li-Na; Lu, Shuai; Tay, Franklin R; Gao, Yu

2014-10-01

To determine whether high-pressure air blowing during adhesive application affects the infiltration of resin comonomers and nanoleakage manifestation in the resin/dentin interface under simulated pulpal pressure. Thirty mid-coronal dentin surfaces were bonded with an etch-and-rinse adhesive (Adper Single Bond 2) under simulated pulpal pressure. In the control group, the adhesive was thinned by ordinary air blowing with a pressure of 0.2 MPa, while in the experimental group, a high-pressure air blowing technique (pressure: 0.4 MPa) was used. All other procedures followed the manufacturer's instructions. Resin tag formation and nanoleakage in the bonding interface were evaluated with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). When adhesive was thinned with high pressure air blowing, longer and more homogeneous resin tags were formed. The bonding interface demonstrated good overall morphology and integrity. Almost perfect infiltration of resin and no obvious nanoleakage were observed. Thinning of adhesive with high-pressure air blowing provides a clinically feasible adjunctive procedure for better resin infiltration.

On the Active and Passive Flow Separation Control Techniques over Airfoils

NASA Astrophysics Data System (ADS)

Moghaddam, Tohid; Banazadeh Neishabouri, Nafiseh

2017-10-01

In the present work, recent advances in the field of the active and passive flow separation control, particularly blowing and suction flow control techniques, applied on the common airfoils are briefly reviewed. This broad research area has remained the point of interest for many years as it is applicable to various applications. The suction and blowing flow control methods, among other methods, are more technically feasible and market ready techniques. It is well established that the uniform and/or oscillatory blowing and suction flow control mechanisms significantly improve the lift-to-drag ratio, and further, postpone the boundary layer separation as well as the stall. The oscillatory blowing and suction flow control, however, is more efficient compared to the uniform one. A wide range of parameters is involved in controlling the behavior of a blowing and/or suction flow control, including the location, length, and angle of the jet slots. The oscillation range of the jet slot is another substantial parameter.

Preparation and characterization of cellulose-based foams via microwave curing

PubMed Central

Demitri, Christian; Giuri, Antonella; Raucci, Maria Grazia; Giugliano, Daniela; Madaghiele, Marta; Sannino, Alessandro; Ambrosio, Luigi

2014-01-01

In this work, a mixture of a sodium salt of carboxymethylcellulose (CMCNa) and polyethylene glycol diacrylate (PEGDA700) was used for the preparation of a microporous structure by using the combination of two different procedures. First, physical foaming was induced using Pluronic as a blowing agent, followed by a chemical stabilization. This second step was carried out by means of an azobis(2-methylpropionamidine)dihydrochloride as the thermoinitiator (TI). This reaction was activated by heating the sample homogeneously using a microwave generator. Finally, the influence of different CMCNa and PEGDA700 ratios on the final properties of the foams was investigated. The viscosity, water absorption capacity, elastic modulus and porous structure were evaluated for each sample. In addition, preliminary biological characterization was carried out with the aim to prove the biocompatibility of the resulting material. The foam, including 20% of PEGDA700 in the mixture, demonstrated higher viscosity and stability before thermo-polymerization. In addition, increased water absorption capacity, mechanical resistance and a more uniform microporous structure were obtained for this sample. In particular, foam with 3% of CMCNa shows a hierarchical structure with open pores of different sizes. This morphology increased the properties of the foams. The full set of samples demonstrated an excellent biocompatibility profile with a good cell proliferation rate of more than 7 days. PMID:24501679

Antifungal efficiency of a lipopeptide biosurfactant derived from Bacillus subtilis SPB1 versus the phytopathogenic fungus, Fusarium solani.

PubMed

Mnif, Ines; Hammami, Ines; Triki, Mohamed Ali; Azabou, Manel Cheffi; Ellouze-Chaabouni, Semia; Ghribi, Dhouha

2015-11-01

Bacillus subtilis SPB1 lipopeptides were evaluated as a natural antifungal agent against Fusarium solani infestation. In vitro antifungal assay showed a minimal inhibitory concentration of about 3 mg/ml with a fungicidal mode of action. In fact, treatment of F. solani by SPB1 lipopeptides generated excessive lyses of the mycelium and caused polynucleation and destruction of the related spores together with a total inhibition of spore production. Furthermore, an inhibition of germination potency accompanied with a high spore blowing was observed. Moreover, in order to be applied in agricultural field, in vivo antifungal activity was proved against the dry rot potato tubers caused by F. solani. Preventive treatment appeared as the most promising as after 20 days of fungi inoculation, rot invasion was reduced by almost 78%, in comparison to that of non-treated one. When treating infected tomato plants, disease symptoms were reduced by almost 100% when applying the curative method. Results of this study are very promising as it enables the use of the crude lipopeptide preparation of B. subtilis SPB1 as a potent natural fungicide that could effectively control the infection of F. solani in tomato and potato tubers at a concentration similar to the commercial fungicide hymexazol and therefore prevent the damage of olive tree.

Developing and teaching the virtue-ethics foundations of healthcare whistle blowing.

PubMed

Faunce, Thomas

2004-10-01

Healthcare whistle blowing, despite the benefits it has brought to healthcare systems in many developed countries, remains generally regarded as a pariah activity by many of the most influential healthcare professionals and regulatory institutions. Few if any medical schools or law department health law and bioethics classes, teach whistle blowing in a formal sense. Yet without exception, public inquiries initiated by healthcare whistle blowers have validated their central allegations and demonstrated that the whistle blowers themselves were sincere in their desire to implement the fundamental virtues and principles of medical ethics, bioethics and public health law. In many jurisdictions, the law, this time remarkably in advance of professional opinion, has offered legislative protection for reasonable allegations of whistleblowers made in good faith and in the public interest concerning a substantial and imminent threat to public safety. One reason for this paradoxical position, explored here, is that healthcare whistle blowing lacks a firm virtue-based theoretical bioethical and jurisprudential foundation. The hypothesis discussed is that the lack of this bioethical and jurisprudential substrate has contributed to a situation where healthcare whistle blowing suffers in terms of institutional support due to its lack of academic legitimacy. This article commences the process of redressing this imbalance by attempting to lay the theoretical foundations for healthcare whistle blowing. As a case study, this article concludes by discussing the Personal and Professional Development course at the ANU Medical School where healthcare whistle blowing is a formal part of a virtue-based curriculum that emphasises the foundational importance of conscience. Illustrative elements of that program are discussed.

Ommatidia of blow fly, house fly, and flesh fly: implication of their vision efficiency.

PubMed

Sukontason, Kabkaew L; Chaiwong, Tarinee; Piangjai, Somsak; Upakut, Sorawit; Moophayak, Kittikhun; Sukontason, Kom

2008-06-01

This work aims to elucidate the number of ommatidia or facets (the outwardly visible units of each ommatidium) for compound eyes in blow flies [Chrysomya megacephala (F.), Chrysomya rufifacies (Macquart), Chrysomya nigripes (Aubertin), Lucilia cuprina (Wiedemann)], house flies (Musca domestica L.), and flesh flies (Liosarcophaga dux Thomson) by manual counts of the corneal spreads. The head of the fly in each species was soaked in 20% potassium hydroxide solution at room temperature for 7 days, and the clear compound eye was dissected into six small parts, each of which was placed onto a slide and flattened using a coverslip. Images of each part were obtained using a microscope connected to a computer. The printed images of each part were magnified, and the total number of ommatidia per eye was manually counted. For males, the mean number of ommatidia was statistically different among all flies examined: L. dux (6,032) > C. rufifacies (5,356) > C. nigripes (4,798) > C. megacephala (4,376) > L. cuprina (3,665) > M. domestica (3,484). Likewise, the mean number of facets in females was statistically different: L. dux (6,086) > C. megacephala (5,641) > C. rufifacies (5,208) > C. nigripes (4,774) > L. cuprina (3,608) > M. domestica (3433). Scanning electron microscopy analysis of adult flies revealed the sexual dimorphism in the compound eye. Male C. megacephala had large ommatidia in the upper two thirds part and small ommatidia in the lower one third part, whereas only small ommatidia were detected in females. Dense postulate appearance was detected in the external surface of the corneal lens of the ommatidia of C. megacephala, C. rufifacies, and C. nigripes, while a mix of dense postulate appearance and variable groove array length was detected in L. cuprina and M. domestica. The probable functions of ommatidia are discussed with reference to other literature.

Simultaneous silencing of ACSL4 and induction of GADD45B in hepatocellular carcinoma cells amplifies the synergistic therapeutic effect of aspirin and sorafenib

PubMed Central

Xia, Hongping; Lee, Kee Wah; Chen, Jianxiang; Kong, Shik Nie; Sekar, Karthik; Deivasigamani, Amudha; Seshachalam, Veerabrahma Pratap; Goh, Brian Kim Poh; Ooi, London Lucien; Hui, Kam M

2017-01-01

Sorafenib is currently the only US Food and Drug Administration (FDA)-approved molecular inhibitor for the systemic therapy of advanced hepatocellular carcinoma (HCC). Aspirin has been studied extensively as an anti-inflammation, cancer preventive and therapeutic agent. However, the potential synergistic therapeutic effects of sorafenib and aspirin on advanced HCC treatment have not been well studied. Drug combination studies and their synergy quantification were performed using the combination index method of Chou-Talalay. The synergistic therapeutic effects of sorafenib and aspirin were evaluated using an orthotopic mouse model of HCC and comprehensive gene profiling analyses were conducted to identify key factors mediating the synergistic therapeutic effects of sorafenib and aspirin. Sorafenib was determined to act synergistically on HCC cells with aspirin in vitro. Using Hep3B and HuH7 HCC cells, it was demonstrated that sorafenib and aspirin acted synergistically to induce apoptosis. Mechanistic studies demonstrated that combining sorafenib and aspirin yielded significant synergistically anti-tumor effects by simultaneously silencing ACSL4 and the induction of GADD45B expression in HCC cells both in vitro and in the orthotopic HCC xenograft mouse model. Importantly, clinical evidence has independently corroborated that survival of HCC patients expressing ACSL4highGADD45Blow was significantly poorer compared to patients with ACSL4lowGADD45Bhigh, thus demonstrating the potential clinical value of combining aspirin and sorafenib for HCC patients expressing ACSL4highGADD45Blow. In conclusion, sorafenib and aspirin provide synergistic therapeutic effects on HCC cells that are achieved through simultaneous silencing of ACSL4 and induction of GADD45B expression. Targeting HCC with ACSL4highGADD45Blow expression with aspirin and sorafenib could provide potential synergistic therapeutic benefits. PMID:28900541

Synthesis characterization and in vitro drug release from acrylamide and sodium alginate based superporous hydrogel devices

PubMed Central

Nagpal, Manju; Singh, Shailendra Kumar; Mishra, Dinanath

2013-01-01

Objective: Present investigation was aimed at developing gastroretentive superporous hydrogels (SPHs) having desired mechanical characteristics with sustained release. Materials and Methods: The acrylamide based SPHs of various generations (1st, 2nd and 3rd) were synthesized by gas blowing technique. The prepared SPHs were evaluated for swelling, mechanical strength studies and scanning electron microscopy studies. Verapamil hydrochloride was loaded into selected SPHs by aqueous drug loading method and characterized via Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (X-RD), differential scanning calorimetry (DSC), nuclear magnetic resonance (NMR) and in vitro drug release studies. Results: SPHs of third generation were observed to have desired mechanical strength with sufficient swelling properties. Integrity of the drug was maintained in hydrogel polymeric network as indicated by FTIR, X-RD, and DSC and NMR studies. Initially, fast drug release (up to 60%) was observed in 30 min in formulation batches containing pure drug only (A, C and E), which was further sustained untill 24 h. Discussion: The increase in mechanical strength was due to the chemical cross-linking of secondary polymer in hydrogel network. The initial burst release was due to the presence of free drug at the surface and later sustained drug release was due to diffusion of entrapped drug in polymeric network. Significant decrease in drug release was observed by the addition of hydroxypropyl methyl cellulose. Conclusion: SPH interpenetrating networks with fast swelling and sufficient mechanical strength were prepared, which can be potentially exploited for designing gastroretentive drug delivery devices. PMID:24167785

British Association of Plastic Surgeons Program from another generation.

PubMed

Freshwater, M Felix

2010-05-01

To Compare the Association's Summer Programs of 1971 and 2008. I attended the 1971 meeting of BAPS that was held in London and kept the program. I compared the content of that meeting with the 2008 Provisional Program. A blow-up of that 1971 program will be the highlight of the poster. The 1971 meeting's registration fee was 10 pounds for me as an overseas non-member registering at the desk compared to the current fee of 500 pounds. The meeting was three day long, but only one day was devoted to papers. The first and third days of the meeting were devoted to watching live cranio-facial surgery performed by Tessier at the Hospital for Sick Children. To make the length of these televised sessions more tolerable, a cash bar was available and lunch including beer and squash were served from noon until 4 pm followed by tea from 4 pm to 6 pm Dinner Jackets were required for the 1971 Association dinner compared with dark lounge suits in 2008. In contrast to 2008, the 1971 scientific program consisted of only 13 papers of which all but five were written by single authors. Seven of the papers were published in the British Journal of Plastic Surgery. There were no cosmetic and no breast papers. There were no poster sessions. There were no panel discussions. There were no exhibits. The 1971 meeting was truly from another generation in both its form and content. Copyright (c) 2009 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Psychrotrophic Clostridium spp. associated with 'blown pack' spoilage of chilled vacuum-packed red meats and dog rolls in gas-impermeable plastic casings.

PubMed

Broda, D M; DeLacy, K M; Bell, R G; Braggins, T J; Cook, R L

1996-04-01

'Blown pack' spoilage of vacuum-packed chilled beef, lamb and venison, and of a cooked meat product, chilled dog rolls packed in an oxygen-impermeable plastic casing, was characterised by sensory, chemical and microbiological analysis. Investigation of the probable causative agents led to the isolation of eight strains of psychrotrophic clostridia. Three strains have been provisionally identified as C. difficile, C. beijerinckii and C. lituseburense; the other five remain unidentified. In inoculation studies only one isolate produced significant amount of gas on meat, causing pack 'blowing'. It is, therefore, possible that 'blown pack' spoilage involves a synergism with one or more other organisms.

The Prevalence of Undiagnosed Concussions in Athletes

PubMed Central

Meehan, William P.; Mannix, Rebekah C.; O'Brien, Michael J.; Collins, Michael W.

2013-01-01

Objective Previous studies suggest athletes underreport concussions. We sought to determine whether athletes in our clinics have sustained previous concussions that went undiagnosed. Design Multi-centered, cross sectional study. Setting Two sport concussion clinics. Patients Patients diagnosed with sport-related concussions or concussions with injury mechanisms and forces similar to those observed in sports were included. Main Outcome Measures The proportion of patients that answered “yes” to the following question were defined as having a previously undiagnosed concussion: “Have you ever sustained a blow to the head which was NOT diagnosed as a concussion but was followed by one or more of the signs and symptoms listed in the Post Concussion Symptom Scale.” Results Of the 486 patients included in the final analysis, 148 (30.5%) reported a previously undiagnosed concussion. Athletes reporting previously undiagnosed concussions had a higher mean Post Concussion Symptom Scale score (33 v. 25; p < 0.004) and were more likely to have lost consciousness (31% v. 22%; p = 0.038) with their current injury than athletes without previously undiagnosed concussions. Conclusions Nearly one third of athletes have sustained previously undiagnosed concussions, defined as a blow to the head followed by the signs and symptoms included in the post concussion symptom scale. Furthermore, these previously undiagnosed concussions are associated with higher post concussion symptom scale scores and higher loss of consciousness rates when future concussions occur. PMID:23727697

Microbiology and resistance in first episodes of spontaneous bacterial peritonitis: implications for management and prognosis.

PubMed

Friedrich, Kilian; Nüssle, Simone; Rehlen, Tobias; Stremmel, Wolfgang; Mischnik, Alexander; Eisenbach, Christoph

2016-06-01

International guidelines for antibiotic treatment of spontaneous bacterial peritonitis (SBP) are based on studies conducted decades ago and do not reflect regional differences of bacterial epidemiology. We retrospectively analyzed epidemiology of agents, antibiotic resistance patterns, and survival in liver cirrhosis patients with their first episode of SBP during the years 2007-2013. Of the 311 patients included, 114 patients had a positive ascites culture, and 197 had an ascitic neutrophil count >250 μL. Gram-positive bacteria (47.8%) were more frequently found than Gram-negatives (44.9%), fungi in 7.2%. Enterobacter spp. (40.6%), Enterococcus spp. (26.1%), and Staphylcoccus spp. (13.8%) were the most frequently isolated agents. Third-generation cephalosporins covered 70.2% of non-nosocomial and 56.3% of nosocomial-acquired SBP cases.When SBP was diagnosed by a positive ascitic culture, survival was highly significantly reduced (mean: 13.9 ± 2.9 months; 95% confidence interval [CI]: 8.1-19.8) compared with culture-negative SBP patients (mean: 44.1 ± 5.4 months; 95% CI: 33.4-54.9; P = 0.000). Along with model of end-stage liver disease score and intensive care unit contact, a positive ascites culture remained an independent risk factor associated with poor survival (odds ratio: 1.49; 95% CI: 1.09-2.03) in multivariate analysis; piperacillin/tazobactam proved to be an adequate antibiotic for nosocomial and non-nosocomial SBP in 85.1% and 92.5%, respectively. SBP infection with Enterococcus spp. was associated with poor patient survival (P = 0.048). Third-generation cephalosporins have poor microbial coverage for treatment of SBP. Current guidelines need to adapt for the emerging number of Gram-positive infectious agents in SBP patients. © 2015 Journal of Gastroenterology and Hepatology Foundation and John Wiley & Sons Australia, Ltd.

Surveillance of antimicrobial susceptibility of aerobic and facultative Gram-negative bacilli isolated from patients with intra-abdominal infections in China: the 2002-2009 Study for Monitoring Antimicrobial Resistance Trends (SMART).

PubMed

Yang, Qiwen; Wang, Hui; Chen, Minjun; Ni, Yuxing; Yu, Yunsong; Hu, Bijie; Sun, Ziyong; Huang, Wenxiang; Hu, Yunjian; Ye, Huifen; Badal, Robert E; Xu, Yingchun

2010-12-01

The objective of this study was to investigate the distribution and susceptibility of aerobic and facultative Gram-negative bacilli (GNB) isolated from patients with intra-abdominal infections (IAIs) in China. From 2002 to 2009, minimum inhibitory concentrations of 14 antibiotics for 3420 aerobic and facultative GNB from up to eight hospitals in six cities were determined by the broth microdilution method. Enterobacteriaceae comprised 82.9% (2834/3420) of the total isolates, with Escherichia coli (49.2%) being the most commonly isolated species followed by Klebsiella pneumoniae (17.0%), Enterobacter cloacae (5.8%) and Citrobacter freundii (2.3%). Amongst the antimicrobial agents tested, the three carbapenems (ertapenem, imipenem and meropenem) were the most active agents against Enterobacteriaceae, with susceptibility rates of 96.1-99.6% (2002-2009), 98.2-100% (2002-2009) and 99.6-100% (2002-2004), respectively, followed by amikacin (86.8-95.1%) and piperacillin/tazobactam (84.5-94.3%). Susceptibility rates of all tested third- and fourth-generation cephalosporins against Enterobacteriaceae declined by nearly 30%, with susceptibility rates of 40.2%, 39.1%, 56.3% and 51.8% in 2009 for ceftriaxone, cefotaxime, ceftazidime and cefepime, respectively. The occurrence of extended-spectrum β-lactamases increased rapidly, especially for E. coli (from 20.8% in 2002 to 64.9% in 2009). Susceptibility of E. coli to ciprofloxacin decreased from 57.6% in 2002 to 24.2% in 2009. The least active agent against Enterobacteriaceae was ampicillin/sulbactam (SAM) (25.3-44.3%). In conclusion, Enterobacteriaceae were the major pathogens causing IAIs, and carbapenems retained the highest susceptibility rates over the 8-year study period. Third- and fourth-generation cephalosporins, fluoroquinolones and SAM may not be ideal choices for empirical therapy of IAIs in China. Copyright © 2010 Elsevier B.V. and the International Society of Chemotherapy. All rights reserved.

Zoledronic acid: a review of its use in the treatment of osteoporosis.

PubMed

Deeks, Emma D; Perry, Caroline M

2008-01-01

Zoledronic acid (Aclasta; Reclast), a third-generation nitrogen-containing bisphosphonate, is the first once-yearly treatment to have been approved for use in patients with postmenopausal osteoporosis or at high risk of fracture. Intravenous zoledronic acid 5 mg once yearly is effective in reducing the risk of several types of fracture in patients with postmenopausal osteoporosis or recent low-trauma hip fracture. Moreover, improvements in bone mineral density (BMD) and reductions in markers of bone turnover are also generally observed. Zoledronic acid is generally well tolerated. Additional comparative data are required to definitively position zoledronic acid with respect to other agents. In the meantime, intravenous zoledronic acid 5 mg once yearly is a convenient and effective treatment option that may have an advantage over some other agents, for which adherence to treatment regimens is a recognized problem.

Simulated Models Suggest That Price per Calorie Is the Dominant Price Metric That Low-Income Individuals Use for Food Decision Making123

PubMed Central

2016-01-01

Background: The price of food has long been considered one of the major factors that affects food choices. However, the price metric (e.g., the price of food per calorie or the price of food per gram) that individuals predominantly use when making food choices is unclear. Understanding which price metric is used is especially important for studying individuals with severe budget constraints because food price then becomes even more important in food choice. Objective: We assessed which price metric is used by low-income individuals in deciding what to eat. Methods: With the use of data from NHANES and the USDA Food and Nutrient Database for Dietary Studies, we created an agent-based model that simulated an environment representing the US population, wherein individuals were modeled as agents with a specific weight, age, and income. In our model, agents made dietary food choices while meeting their budget limits with the use of 1 of 3 different metrics for decision making: energy cost (price per calorie), unit price (price per gram), and serving price (price per serving). The food consumption patterns generated by our model were compared to 3 independent data sets. Results: The food choice behaviors observed in 2 of the data sets were found to be closest to the simulated dietary patterns generated by the price per calorie metric. The behaviors observed in the third data set were equidistant from the patterns generated by price per calorie and price per serving metrics, whereas results generated by the price per gram metric were further away. Conclusions: Our simulations suggest that dietary food choice based on price per calorie best matches actual consumption patterns and may therefore be the most salient price metric for low-income populations. PMID:27655757

Simulated Models Suggest That Price per Calorie Is the Dominant Price Metric That Low-Income Individuals Use for Food Decision Making.

PubMed

Beheshti, Rahmatollah; Igusa, Takeru; Jones-Smith, Jessica

2016-11-01

The price of food has long been considered one of the major factors that affects food choices. However, the price metric (e.g., the price of food per calorie or the price of food per gram) that individuals predominantly use when making food choices is unclear. Understanding which price metric is used is especially important for studying individuals with severe budget constraints because food price then becomes even more important in food choice. We assessed which price metric is used by low-income individuals in deciding what to eat. With the use of data from NHANES and the USDA Food and Nutrient Database for Dietary Studies, we created an agent-based model that simulated an environment representing the US population, wherein individuals were modeled as agents with a specific weight, age, and income. In our model, agents made dietary food choices while meeting their budget limits with the use of 1 of 3 different metrics for decision making: energy cost (price per calorie), unit price (price per gram), and serving price (price per serving). The food consumption patterns generated by our model were compared to 3 independent data sets. The food choice behaviors observed in 2 of the data sets were found to be closest to the simulated dietary patterns generated by the price per calorie metric. The behaviors observed in the third data set were equidistant from the patterns generated by price per calorie and price per serving metrics, whereas results generated by the price per gram metric were further away. Our simulations suggest that dietary food choice based on price per calorie best matches actual consumption patterns and may therefore be the most salient price metric for low-income populations. © 2016 American Society for Nutrition.

Deuterium Tetrabenazine for Tardive Dyskinesia.

PubMed

Cummings, Michael A; Proctor, George J; Stahl, Stephen M

2018-01-01

Tardive dyskinesia remains a significant, potentially stigmatizing or crippling adverse effect for any patient treated with an antipsychotic medication. While second- and third-generation antipsychotics have exhibited lower annual incidence rates for tardive dyskinesia than classic or first-generation agents, 3.9% versus 5.5%, the estimated incidence rate is only modestly lower. When coupled with the fact that second- and third-generation antipsychotic medications have come to be employed in treating a wider range of disorders (e.g., autism spectrum disorders, mood disorders, personality disorders, etc.), it is clear that the population of patients exposed to the risk of tardive dyskinesia has expanded. On April 3, 2017, the U.S. Food and Drug Administration (FDA) approved a deuterated version of tetrabenazine (Xenozine®) for the treatment of the involuntary choreic movements associated with Huntington's disease. More recent data, however, have indicated that deuterium tetrabenazine or deutetrabenazine (Austedo®) is effective in treating tardive dyskinesia. Moreover, like the other derivative of tetrabenazine, valbenazine (Ingrezza®), deutetrabenazine offers less frequent dosing and a better short-term adverse effect profile than that of tetrabenazine. Longer use in a broader range of patients, however, will be required to identify risks and benefits not found in short-term trials, as well as optimal use parameters for treatment of tardive dyskinesia.

Speeding Up Social Waves. Propagation Mechanisms of Shimmering in Giant Honeybees

PubMed Central

Kastberger, Gerald; Hoetzl, Thomas; Maurer, Michael; Kranner, Ilse; Weiss, Sara; Weihmann, Frank

2014-01-01

Shimmering is a defence behaviour in giant honeybees (Apis dorsata), whereby bees on the nest surface flip their abdomen upwards in a Mexican wave-like process. However, information spreads faster than can be ascribed to bucket bridging, which is the transfer of information from one individual to an adjacent one. We identified a saltatoric process that speeds up shimmering by the generation of daughter waves, which subsequently merge with the parental wave, producing a new wave front. Motion patterns of individual “focus” bees (n = 10,894) and their shimmering-active neighbours (n = 459,558) were measured with high-resolution video recording and stereoscopic imaging. Three types of shimmering-active surface bees were distinguished by their communication status, termed “agents”: “Bucket-bridging” agents comprised 74.98% of all agents, affected 88.17% of their neighbours, and transferred information at a velocity of v = 0.317±0.015 m/s. “Chain-tail” agents comprised 9.20% of the agents, were activated by 6.35% of their neighbours, but did not motivate others to participate in the wave. “Generator agents” comprised 15.82% of agents, showed abdominal flipping before the arrival of the main wave front, and initiated daughter waves. They affected 6.75% of their neighbourhood and speeded up the compound shimmering process compared to bucket bridging alone by 41.5% to v = 0.514±0.019 m/s. The main direction of shimmering was reinforced by 35.82% of agents, whereas the contribution of the complementing agents was fuzzy. We discuss that the saltatoric process could enable the bees to instantly recruit larger cohorts to participate in shimmering and to respond rapidly to changes in flight direction of preying wasps. A third, non-exclusive explanation is that at a distance of up to three metres from the nest the acceleration of shimmering could notably contribute to the startle response in mammals and birds. PMID:24475104

Viscous flow drag reduction; Symposium, Dallas, Tex., November 7, 8, 1979, Technical Papers

NASA Technical Reports Server (NTRS)

Hough, G. R.

1980-01-01

The symposium focused on laminar boundary layers, boundary layer stability analysis of a natural laminar flow glove on the F-111 TACT aircraft, drag reduction of an oscillating flat plate with an interface film, electromagnetic precipitation and ducting of particles in turbulent boundary layers, large eddy breakup scheme for turbulent viscous drag reduction, blowing and suction, polymer additives, and compliant surfaces. Topics included influence of environment in laminar boundary layer control, generation rate of turbulent patches in the laminar boundary layer of a submersible, drag reduction of small amplitude rigid surface waves, and hydrodynamic drag and surface deformations generated by liquid flows over flexible surfaces.

Evaluation of mechanical losses in a linear motor pressure wave generator

NASA Astrophysics Data System (ADS)

Jacob, Subhash; Rangasamy, Karunanithi; Jonnalagadda, Kranthi Kumar; Chakkala, Damu; Achanur, Mallappa; Govindswamy, Jagadish; Gour, Abhay Singh

2012-06-01

A moving magnet linear motor compressor or pressure wave generator (PWG) of 2 cc swept volume with dual opposed piston configuration has been developed to operate miniature pulse tube coolers. Prelimnary experiments yielded only a no-load cold end temperature of 180 K. Auxiliary tests and the interpretation of detailed modeling of a PWG suggest that much of the PV power has been lost in the form of blow-by at piston seals due to large and non-optimum clearance seal gap between piston and cylinder. The results of experimental parameters simulated using Sage provide the optimum seal gap value for maximizing the delivered PV power.

Mechanics of Micro- and Nano-Textured Systems: Nanofibers, Nanochannels, Nanoparticles and Slurries

NASA Astrophysics Data System (ADS)

Sinha Ray, Suman

The first chapter of this work deals with bundles of microscopically long carbon nanochannels, which were assembled as a nanofluidic device to study bi-layer flows of n-decane and air. These experiments were accompanied and supported by theoretical considerations. The study paradoxically showed that it is possible to deliver more liquid through the nanochannels if they are partially filled with liquid in comparison to those which are completely filled with liquid. In the following chapter these nanochannels were used to produce thermoresponsive nanoparticles (˜400 nm in diameter) at a very high production rate of 107 particles/sec. These nanoparticles were loaded with a low molecular weight dye to study the thermoresponsive release profile experimentally. The experiments were accompanied and guided by theoretical work. In the third part of the work, a rigorous electron microscopy revealed the 2-nm islands of thermoresponsive hydrogels nanofibers produced by electrospinning and cross-linking of electropun PNIPAM-containing nanofibers. These islands were found to be responsible for positive thermosensitivity in dye release experiments. In the following chapters meltblowing was studied both experimentally and theoretically. The role of air turbulence in this process was elucidated experimentally by blowing a solid flexible threadline in high-speed gas flow. Using this information, theoretical understanding of polymer jet/gas jet turbulent interactions was achieved and a theory of small (linearized) and large (nonlinear) bending perturbations of polymer jets was developed. This theory was extended to simulate numerically multiple polymer jets being deposited on a screen moving normally to the blowing direction. In the subsequent chapter, a novel method, solution blowing, for producing monolithic and core-shell nanofibers was developed. The core-shell fibers were also converted into hollow carbon nanotubes. The carbon nanofiber mats produced by this method were used as an electrode in a microbial fuel cell, which showed a higher current density in comparison to standard polycrystalline graphite rods. In addition, solution blowing was used to form soy-protein-containing biodegradable nanofibers. In the next chapter, a novel method of intercalating wax and butter en masse into carbon nanotubes was demonstrated. It was shown that by manipulating the intercalated solute the working temperature range of phase-change materials (PCM) can be significantly widened, while the response time reduced to minimum. In the final part of the work the elongational rheology of gypsum slurries was also studied and corroborated using the data from the corresponding shear rheological studies. It was shown that the gypsum slurries approximately follow the tensorial Ostwald-de-Waele (power law) constitutive equation.

The mechanisms of flame holding in the wake of a bluff body

NASA Technical Reports Server (NTRS)

Strehlow, R. A.; Malik, S.

1985-01-01

The flame holding mechanism for lean methane- and lean propane-air flames is examined under conditions where the recirculation zone is absent. The main objective of this work is to study the holding process in detail in an attempt to determine the mechanism of flame holding and also the conditions where this mechanism is viable and when it fails and blow-off occurs. Inverted flames held in the wake of a flat strip were studied. Experiments with different sizes of flame holders were performed. The velocity flow field was determined using a laser Doppler velocimetry technique. Equation of continuity was used to calculate the flame temperature from the change in area of flow streamlines before and after the flame. Observations of the inverted flame itself were obtained using schlieren and direct photography. Results show that there are different mechanisms operative at the time of blow-off for lean propane and methane flames. Blow-off or extinction occurs for lean propane-air flame in spite of the reaction going to completion and the disparity between the heat loss and the gain in mass diffusion in the reaction zone i.e., Le 1.0 causes the flame to blow-off. For methane-air flame the controlling factor or blow-off is incomplete reaction due to higher blowing rate leading to reduced residence time in the reaction zone.

Resection and primary anastomosis with or without modified blow-hole colostomy for sigmoid volvulus

PubMed Central

Coban, Sacid; Yilmaz, Mehmet; Terzi, Alpaslan; Yildiz, Fahrettin; Ozgor, Dincer; Ara, Cengiz; Yologlu, Saim; Kirimlioglu, Vedat

2008-01-01

AIM: To evaluate the efficacy of resection and primary anastomosis (RPA) and RPA with modified blow-hole colostomy for sigmoid volvulus. METHODS: From March 2000 to September 2007, 77 patients with acute sigmoid volvulus were treated. A total of 47 patients underwent RPA or RPA with modified blow-hole colostomy. Twenty-five patients received RPA (Group A), and the remaining 22 patients had RPA with modified blow-hole colostomy (Group B). The clinical course and postoperative complications of the two groups were compared. RESULTS: The mean hospital stay, wound infection and mortality did not differ significantly between the groups. Superficial wound infection rate was higher in group A (32% vs 9.1%). Anastomotic leakage was observed only in group A, with a rate of 6.3%. The difference was numerically impressive but was statistically not significant. CONCLUSION: RPA with modified blow-hole colostomy provides satisfactory results. It is easy to perform and may become a method of choice in patients with sigmoid volvulus. Further studies are required to further establish its role in the treatment of sigmoid volvulus. PMID:18810779

Humidification of Blow-By Oxygen During Recovery of Postoperative Pediatric Patients: One Unit's Journey.

PubMed

Donahue, Suzanne; DiBlasi, Robert M; Thomas, Karen

2018-02-02

To examine the practice of nebulizer cool mist blow-by oxygen administered to spontaneously breathing postanesthesia care unit (PACU) pediatric patients during Phase one recovery. Existing evidence was evaluated. Informal benchmarking documented practices in peer organizations. An in vitro study was then conducted to simulate clinical practice and determine depth and amount of airway humidity delivery with blow-by oxygen. Informal benchmarking information was obtained by telephone interview. Using a three-dimensional printed simulation model of the head connected to a breathing lung simulator, depth and amount of moisture delivery in the respiratory tree were measured. Evidence specific to PACU administration of cool mist blow-by oxygen was limited. Informal benchmarking revealed that routine cool mist oxygenated blow-by administration was not widely practiced. The laboratory experiment revealed minimal moisture reaching the mid-tracheal area of the simulated airway model. Routine use of oxygenated cool mist in spontaneously breathing pediatric PACU patients is not supported. Copyright © 2017 American Society of PeriAnesthesia Nurses. Published by Elsevier Inc. All rights reserved.

Aeroacoustic Duster

NASA Technical Reports Server (NTRS)

Wu, Jun-ru (Inventor); Hitt, Darren (Inventor); Vachon, Nicholas M. (Inventor); Chen, Di (Inventor); Marshall, Jeffrey S. (Inventor)

2016-01-01

The invention disclosed herein provides for high particle removal rate and/or heat transfer from surfaces. The device removes particulate matter from a surface using a bounded vortex generated over the surface, with suction in the vortex center and jets for blowing air along the periphery. The jets are tilted in the tangential direction to induce vortex motion within the suction region. The vortex is said to be bounded because streamlines originating in the downward jets are entrained back into the central vortex.

Effects of wall suction/blowing on two-dimensional flow past a confined square cylinder.

PubMed

Zhang, Wei; Jiang, Yanqun; Li, Lang; Chen, Guoping

2016-01-01

A numerical simulation is conducted to study the laminar flow past a square cylinder confined in a channel (the ratio of side length of the square to channel width is fixed at 1/4) subjected to a locally uniform blowing/suction speed placed at the top and bottom channel walls. Governing equations with boundary conditions are resolved using a finite volume method in pressure-velocity formulation. The flow patterns relevant to the critical spacing values are investigated. Numerical results show that wall blowing has a stabilizing effect on the flow, and the corresponding critical Reynolds number increases monotonically with increasing blowing velocity. Remarkably, steady asymmetric solutions and hysteretic mode transitions exist in a certain range of parameters (Reynolds number and suction speed) in the case of suction.

Feasibility study of launch vehicle ground cloud neutralization

NASA Technical Reports Server (NTRS)

Vanderarend, P. C.; Stoy, S. T.; Kranyecz, T. E.

1976-01-01

The distribution of hydrogen chloride in the cloud was analyzed as a function of launch pad geometry and rate of rise of the vehicle during the first 24 sec of burn in order to define neutralization requirements. Delivery systems of various types were developed in order to bring the proposed chemical agents in close contact with the hydrogen chloride. Approximately one-third of the total neutralizing agent required can be delivered from a ground installed system at the launch pad; concentrated sodium carbonate solution is the preferred choice of agent for this launch pad system. Two-thirds of the neutralization requirement appears to need delivery by aircraft. Only one chemical agent (ammonia) may be reasonably considered for delivery by aircraft, because weight and bulk of all other agents are too large.

Requirements for facilities transferring or receiving select agents. Final rule.

PubMed

2001-08-31

CDC administers regulations that govern the transfer of certain biological agents and toxins ("select agents"). These regulations require entities that transfer or receive select agents to register with CDC and comply with biosafety standards contained in the Third Edition of the CDC/NIH publication "Biosafety in Microbiological and Biomedical Laboratories ("BMBL")." On October 28,1999, CDC published a Notice of Proposed Rulemaking ("NPRM") seeking both to revise the biosafety standards facilities must follow when handling select agents and to provide new biosecurity standards for such facilities. These new standards are contained in the Fourth Edition of BMBL, which the NPRM proposed to incorporate by reference, thereby replacing the Third Edition. No comments were received in response to this proposal. CDC is therefore amending its regulations to incorporate the Fourth Edition.

The Polyanalytic Ginibre Ensembles

NASA Astrophysics Data System (ADS)

Haimi, Antti; Hedenmalm, Haakan

2013-10-01

For integers n, q=1,2,3,… , let Pol n, q denote the -linear space of polynomials in z and , of degree ≤ n-1 in z and of degree ≤ q-1 in . We supply Pol n, q with the inner product structure of the resulting Hilbert space is denoted by Pol m, n, q . Here, it is assumed that m is a positive real. We let K m, n, q denote the reproducing kernel of Pol m, n, q , and study the associated determinantal process, in the limit as m, n→+∞ while n= m+O(1); the number q, the degree of polyanalyticity, is kept fixed. We call these processes polyanalytic Ginibre ensembles, because they generalize the Ginibre ensemble—the eigenvalue process of random (normal) matrices with Gaussian weight. There is a physical interpretation in terms of a system of free fermions in a uniform magnetic field so that a fixed number of the first Landau levels have been filled. We consider local blow-ups of the polyanalytic Ginibre ensembles around points in the spectral droplet, which is here the closed unit disk . We obtain asymptotics for the blow-up process, using a blow-up to characteristic distance m -1/2; the typical distance is the same both for interior and for boundary points of . This amounts to obtaining the asymptotical behavior of the generating kernel K m, n, q . Following (Ameur et al. in Commun. Pure Appl. Math. 63(12):1533-1584, 2010), the asymptotics of the K m, n, q are rather conveniently expressed in terms of the Berezin measure (and density) [Equation not available: see fulltext.] For interior points | z|<1, we obtain that in the weak-star sense, where δ z denotes the unit point mass at z. Moreover, if we blow up to the scale of m -1/2 around z, we get convergence to a measure which is Gaussian for q=1, but exhibits more complicated Fresnel zone behavior for q>1. In contrast, for exterior points | z|>1, we have instead that , where is the harmonic measure at z with respect to the exterior disk . For boundary points, | z|=1, the Berezin measure converges to the unit point mass at z, as with interior points, but the blow-up to the scale m -1/2 exhibits quite different behavior at boundary points compared with interior points. We also obtain the asymptotic boundary behavior of the 1-point function at the coarser local scale q 1/2 m -1/2.

Optimisation of multi-layer rotationally moulded foamed structures

NASA Astrophysics Data System (ADS)

Pritchard, A. J.; McCourt, M. P.; Kearns, M. P.; Martin, P. J.; Cunningham, E.

2018-05-01

Multi-layer skin-foam and skin-foam-skin sandwich constructions are of increasing interest in the rotational moulding process for two reasons. Firstly, multi-layer constructions can improve the thermal insulation properties of a part. Secondly, foamed polyethylene sandwiched between solid polyethylene skins can increase the mechanical properties of rotationally moulded structural components, in particular increasing flexural properties and impact strength (IS). The processing of multiple layers of polyethylene and polyethylene foam presents unique challenges such as the control of chemical blowing agent decomposition temperature, and the optimisation of cooling rates to prevent destruction of the foam core; therefore, precise temperature control is paramount to success. Long cooling cycle times are associated with the creation of multi-layer foam parts due to their insulative nature; consequently, often making the costs of production prohibitive. Devices such as Rotocooler®, a rapid internal mould water spray cooling system, have been shown to have the potential to significantly decrease cooling times in rotational moulding. It is essential to monitor and control such devices to minimise the warpage associated with the rapid cooling of a moulding from only one side. The work presented here demonstrates the use of threaded thermocouples to monitor the polymer melt in multi-layer sandwich constructions, in order to analyse the cooling cycle of multi-layer foamed structures. A series of polyethylene skin-foam test mouldings were produced, and the effect of cooling medium on foam characteristics, mechanical properties, and process cycle time were investigated. Cooling cycle time reductions of 45%, 26%, and 29% were found for increasing (1%, 2%, and 3%) chemical blowing agent (CBA) amount when using internal water cooling technology from ˜123°C compared with forced air cooling (FAC). Subsequently, a reduction of IS for the same skin-foam parts was found to be 1%, 4%, and 16% compared with FAC.

Blow-up and symmetry of sign-changing solutions to some critical elliptic equations

NASA Astrophysics Data System (ADS)

Ben Ayed, Mohamed; El Mehdi, Khalil; Pacella, Filomena

In this paper we continue the analysis of the blow-up of low energy sign-changing solutions of semi-linear elliptic equations with critical Sobolev exponent, started in [M. Ben Ayed, K. El Mehdi, F. Pacella, Blow-up and nonexistence of sign-changing solutions to the Brezis-Nirenberg problem in dimension three, Ann. Inst. H. Poincaré Anal. Non Linéaire, in press]. In addition we prove axial symmetry results for the same kind of solutions in a ball.

Pavement Maintenance Management for Roads and Parking Lots.

DTIC Science & Technology

1981-10-01

PAVEMENT INSPECTION SHEET aRANCH SECT ION DA TE SAMPLE UNIT SURVEYED BY SLAB SIZE * 0 0 0 Distress Types !0 2f Blow- Up 3’ Polished Buckling/Shattering...10 21 Blow- up 31 Poisnec Buckling/Shatternrg Aggregate 0 1 22. Corner Break 32 Porouis 23. D’viOea SIcD 33 Ptmo,nq 9 24 Durability . " 34 Pancnout...Load Durability Drainage Other Factors Corner Break Blow- up Corner Break Faulting Divided Slab Ŕ" Cracking Divided Slab Lane/Shoulder Dropoff

An experimental investigation of delta wing vortex flow with and without external jet blowing

NASA Technical Reports Server (NTRS)

Iwanski, Kenneth P.; Ng, T. Terry; Nelson, Robert C.

1989-01-01

A visual and quantitative study of the vortex flow field over a 70-deg delta wing with an external jet blowing parallel to and at the leading edge was conducted. In the experiment, the vortex core was visually marked with TiCl4, and LDA was used to measure the velocity parallel and normal to the wing surface. It is found that jet blowing moved vortex breakdown farther downstream from its natural position and influenced the breakdown characteristics.

Blow-up of solutions to a quasilinear wave equation for high initial energy

NASA Astrophysics Data System (ADS)

Li, Fang; Liu, Fang

2018-05-01

This paper deals with blow-up solutions to a nonlinear hyperbolic equation with variable exponent of nonlinearities. By constructing a new control function and using energy inequalities, the authors obtain the lower bound estimate of the L2 norm of the solution. Furthermore, the concavity arguments are used to prove the nonexistence of solutions; at the same time, an estimate of the upper bound of blow-up time is also obtained. This result extends and improves those of [1,2].

Extensive Core Microbiome in Drone-Captured Whale Blow Supports a Framework for Health Monitoring

PubMed Central

Miller, Carolyn A.; Moore, Michael J.; Durban, John W.; Fearnbach, Holly; Barrett-Lennard, Lance G.

2017-01-01

ABSTRACT The pulmonary system is a common site for bacterial infections in cetaceans, but very little is known about their respiratory microbiome. We used a small, unmanned hexacopter to collect exhaled breath condensate (blow) from two geographically distinct populations of apparently healthy humpback whales (Megaptera novaeangliae), sampled in the Massachusetts coastal waters off Cape Cod (n = 17) and coastal waters around Vancouver Island (n = 9). Bacterial and archaeal small-subunit rRNA genes were amplified and sequenced from blow samples, including many of sparse volume, as well as seawater and other controls, to characterize the associated microbial community. The blow microbiomes were distinct from the seawater microbiomes and included 25 phylogenetically diverse bacteria common to all sampled whales. This core assemblage comprised on average 36% of the microbiome, making it one of the more consistent animal microbiomes studied to date. The closest phylogenetic relatives of 20 of these core microbes were previously detected in marine mammals, suggesting that this core microbiome assemblage is specialized for marine mammals and may indicate a healthy, noninfected pulmonary system. Pathogen screening was conducted on the microbiomes at the genus level, which showed that all blow and few seawater microbiomes contained relatives of bacterial pathogens; no known cetacean respiratory pathogens were detected in the blow. Overall, the discovery of a shared large core microbiome in humpback whales is an important advancement for health and disease monitoring of this species and of other large whales. IMPORTANCE The conservation and management of large whales rely in part upon health monitoring of individuals and populations, and methods generally necessitate invasive sampling. Here, we used a small, unmanned hexacopter drone to noninvasively fly above humpback whales from two populations, capture their exhaled breath (blow), and examine the associated microbiome. In the first extensive examination of the large-whale blow microbiome, we present surprising results about the discovery of a large core microbiome that was shared across individual whales from geographically separated populations in two ocean basins. We suggest that this core microbiome, in addition to other microbiome characteristics, could be a useful feature for health monitoring of large whales worldwide. PMID:29034331

Extensive Core Microbiome in Drone-Captured Whale Blow Supports a Framework for Health Monitoring.

PubMed

Apprill, Amy; Miller, Carolyn A; Moore, Michael J; Durban, John W; Fearnbach, Holly; Barrett-Lennard, Lance G

2017-01-01

The pulmonary system is a common site for bacterial infections in cetaceans, but very little is known about their respiratory microbiome. We used a small, unmanned hexacopter to collect exhaled breath condensate (blow) from two geographically distinct populations of apparently healthy humpback whales ( Megaptera novaeangliae ), sampled in the Massachusetts coastal waters off Cape Cod ( n = 17) and coastal waters around Vancouver Island ( n = 9). Bacterial and archaeal small-subunit rRNA genes were amplified and sequenced from blow samples, including many of sparse volume, as well as seawater and other controls, to characterize the associated microbial community. The blow microbiomes were distinct from the seawater microbiomes and included 25 phylogenetically diverse bacteria common to all sampled whales. This core assemblage comprised on average 36% of the microbiome, making it one of the more consistent animal microbiomes studied to date. The closest phylogenetic relatives of 20 of these core microbes were previously detected in marine mammals, suggesting that this core microbiome assemblage is specialized for marine mammals and may indicate a healthy, noninfected pulmonary system. Pathogen screening was conducted on the microbiomes at the genus level, which showed that all blow and few seawater microbiomes contained relatives of bacterial pathogens; no known cetacean respiratory pathogens were detected in the blow. Overall, the discovery of a shared large core microbiome in humpback whales is an important advancement for health and disease monitoring of this species and of other large whales. IMPORTANCE The conservation and management of large whales rely in part upon health monitoring of individuals and populations, and methods generally necessitate invasive sampling. Here, we used a small, unmanned hexacopter drone to noninvasively fly above humpback whales from two populations, capture their exhaled breath (blow), and examine the associated microbiome. In the first extensive examination of the large-whale blow microbiome, we present surprising results about the discovery of a large core microbiome that was shared across individual whales from geographically separated populations in two ocean basins. We suggest that this core microbiome, in addition to other microbiome characteristics, could be a useful feature for health monitoring of large whales worldwide.

Blow Up

ERIC Educational Resources Information Center

Carringer, Robert L.

1975-01-01

An evaluation of the career of Michelangelo Antonioni and his best known film, Blow Up, were followed with credits for the film, a sequence outline, study questions for class discussion, and some suggestions for additional reading. (RK)

Control of vortical separation on conical bodies

NASA Technical Reports Server (NTRS)

Mourtos, Nikos J.; Roberts, Leonard

1987-01-01

In a variety of aeronautical applications, the flow around conical bodies at incidence is of interest. Such applications include, but are not limited to, highly maneuverable aircraft with delta wings, the aerospace plane and nose portions of spike inlets. The theoretical model used has three parts. First, the single line vortex model is used within the framework of slender body theory, to compute the outer inviscid field for specified separation lines. Next, the three dimensional boundary layer is represented by a momentum equation for the cross flow, analogous to that for a plane boundary layer; a von Karman Pohlhausen approximation is applied to solve this equation. The cross flow separation for both laminar and turbulent layers is determined by matching the pressure at the upper and lower separation points. This iterative procedure yields a unique solution for the separation lines and consequently for the position of the vortices and the vortex lift on the body. Lastly, control of separation is achieved by blowing tangentially from a slot located along a cone generator. It is found that for very small blowing coefficients, the separation can be postponed or suppressedy completely.

Neonatal suppurative parotitis over the last 4 decades: report of three new cases and review.

PubMed

Ismail, Essam A; Seoudi, Tarek M; Al-Amir, Mohamad; Al-Esnawy, Ahmad A

2013-02-01

Neonatal suppurative parotitis is a rare disease. Only 32 cases were reported in the English-language literature between 1970 and 2004. We searched Medline for acute, neonatal, bacterial, suppurative, parotitis, facial, preauricular swelling starting from 1970, limiting our search to the English-language literature. We reviewed all the reported cases together with three more managed in our department. We identified nine new cases since 2004. The total number of patients reviewed was 44, including our patients. Most of them were male (77%). The majority developed unilateral inflamed parotid swelling (77%) and exuded pus from the ipsilateral Stensen duct. Fever was seen in fewer than half of them (47%). Premature babies constituted a third of the patients. Staphylococcus aureus was the leading causative agent (61%). Most patients responded well to conservative treatment with antibiotics (77%). The most frequently used combination of antibiotics was an anti-staphylococcal agent with either an aminoglycoside or a third-generation cephalosporin. A minority required surgical drainage. No deaths were reported in the group studied after 1970. Neonatal suppurative parotitis is rare but easy to diagnose and if readily treated with appropriate antibiotics the outcome is excellent. © 2012 The Authors. Pediatrics International © 2012 Japan Pediatric Society.

Predictors of responses to organizational wrongdoing: a study of intentions of management accountants.

PubMed

Casal, Jose C; Bogui, Frederic B

2008-08-01

It has been proposed that employees aware of organizational wrongdoing face two decisions: whether or not to blow the whistle and whether or not to leave their organizations. Of these only the decision to blow the whistle has received attention, leaving a gap in knowledge; thus, a survey of 330 management accountants was analyzed to examine potential predictors of intended responses to organizational wrongdoing. Analysis of ratings indicated that intent to leave increased with seriousness of wrongdoing and expected retaliation for whistleblowing and decreased with expected effectiveness of whistleblowing. Intent to stay and blow the whistle increased with expected effectiveness of whistleblowing and role responsibility for reporting and decreased with expected retaliation for whistleblowing; intent to leave and blow the whistle increased with expected effectiveness of whistleblowing and role responsibility for reporting.

Earthquake-induced liquefaction features in the coastal setting of South Carolina and in the fluvial setting of the New Madrid Seismic Zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Obermeier, S.F.; Jacobson, R.B.; Smoot, J.P.

1990-01-01

In both coastal South Carolina and the New Madrid seismic zone, the earthquake-induced liquefaction features generally originated in clean sand deposits that contain no or few intercalated silt- or clay-rich strata. The local geologic setting is a major influence on both development and surface expression of sand blows. Major factors controlling sand-blow formation include the thickness and physical properties of the deposits above the source sands, and these relationships are illustrated by comparing sand blows found in coastal South Carolina (in marine deposits) with sand blows found in the New Madrid seismic zone (in fluvial deposits). In coastal South Carolina,more » the surface stratum is typically a thin (about 1 m) soil that is weakly cemented with humate, and the sand blows are expressed as craters surrounded by a thin sheet of sand; in the New Madrid seismic zone the surface stratum generally is a clay-rich deposit ranging in thickness from 2 to 10 m, in which case sand blows characteristically are expressed as sand mounded above the original ground surface. Recognition of the various features described in this paper, and identification of the most probable origin for each, provides a set of important tools for understanding paleoseismicity in areas such as the Central and Eastern US where faults are not exposed for study and strong seismic activity is infrequent.« less

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Technical Reports Server (NTRS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-01-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Astrophysics Data System (ADS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-11-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Hybrid LES/RANS Simulation of the Effects of Boundary Layer Control Devices Using Immersed Boundary Methods

DTIC Science & Technology

2010-02-22

any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a... its use in simulating the effects of different types of flow control devices: micro vortex generators, bleed-hole arrays, aero- elastically...large scale, and that local pressure differences can lead to periodic blowing / suction even in “active” control devices [5], it appears that

Assessing the stretch-blow moulding FE simulation of PET over a large process window

NASA Astrophysics Data System (ADS)

Nixon, J.; Menary, G. H.; Yan, S.

2017-10-01

Injection stretch blow moulding has been extensively researched for numerous years and is a well-established method of forming thin-walled containers. This paper is concerned with validating the finite element analysis of the stretch-blow-moulding (SBM) process in an effort to progress the development of injection stretch blow moulding of poly(ethylene terephthalate). Extensive data was obtained experimentally over a wide process window accounting for material temperature, air flow rate and stretch-rod speed while capturing cavity pressure, stretch-rod reaction force, in-mould contact timing and material thickness distribution. This data was then used to assess the accuracy of the correlating FE simulation constructed using ABAQUS/Explicit solver and an appropriate user-defined viscoelastic material subroutine. Results reveal that the simulation was able to pick up the general trends of how the pressure, reaction force and in-mould contact timings vary with the variation in preform temperature and air flow rate. Trends in material thickness were also accurately predicted over the length of the bottle relative to the process conditions. The knowledge gained from these analyses provides insight into the mechanisms of bottle formation, subsequently improving the blow moulding simulation and potentially providing a reduction in production costs.

Physical Modelling of the Effect of Slag and Top-Blowing on Mixing in the AOD Process

NASA Astrophysics Data System (ADS)

Haas, Tim; Visuri, Ville-Valtteri; Kärnä, Aki; Isohookana, Erik; Sulasalmi, Petri; Eriç, Rauf Hürman; Pfeifer, Herbert; Fabritius, Timo

The argon-oxygen decarburization (AOD) process is the most common process for refining stainless steel. High blowing rates and the resulting efficient mixing of the steel bath are characteristic of the AOD process. In this work, a 1:9-scale physical model was used to study mixing in a 150 t AOD vessel. Water, air and rapeseed oil were used to represent steel, argon and slag, respectively, while the dynamic similarity with the actual converter was maintained using the modified Froude number and the momentum number. Employing sulfuric acid as a tracer, the mixing times were determined on the basis of pH measurements according to the 97.5% criterion. The gas blowing rate and slag-steel volume ratio were varied in order to study their effect on the mixing time. The effect of top-blowing was also investigated. The results suggest that mixing time decreases as the modified Froude number of the tuyères increases and that the presence of a slag layer increases the mixing time. Furthermore, top-blowing was found to increase the mixing time both with and without the slag layer.

A new impulsive seismic shear wave source for near-surface (0-30 m) seismic studies

NASA Astrophysics Data System (ADS)

Crane, J. M.; Lorenzo, J. M.

2010-12-01

Estimates of elastic moduli and fluid content in shallow (0-30 m) natural soils below artificial flood containment structures can be particularly useful in levee monitoring as well as seismic hazard studies. Shear wave moduli may be estimated from horizontally polarized, shear wave experiments. However, long profiles (>10 km) with dense receiver and shot spacings (<1m) cannot be collected efficiently using currently available shear wave sources. We develop a new, inexpensive, shear wave source for collecting fast, shot gathers over large acquisition sites. In particular, gas-charged, organic-rich sediments comprising most lower-delta sedimentary facies, greatly attenuate compressional body-waves. On the other hand, SH waves are relatively insensitive to pore-fluid moduli and can improve resolution. We develop a recoil device (Jolly, 1956) into a single-user, light-weight (<20 kg), impulsive, ground-surface-coupled SH wave generator, which is capable of working at rates of several hundred shotpoints per day. Older impulsive methods rely on hammer blows to ground-planted stationary targets. Our source is coupled to the ground with steel spikes and the powder charge can be detonated mechanically or electronically. Electrical fuses show repeatability in start times of < 50 microseconds. The barrel and shell-holder exceed required thicknesses to ensure complete safety during use. The breach confines a black-powder, 12-gauge shotgun shell, loaded with inert, environmentally safe ballast. In urban settings, produced heat and sound are confined by a detached, exterior cover. A moderate 2.5 g black-powder charge generates seismic amplitudes equivalent to three 4-kg sledge-hammer blows. We test this device to elucidate near subsurface sediment properties at former levee breach sites in New Orleans, Louisiana, USA. Our radio-telemetric seismic acquisition system uses an in-house landstreamer, consisting of 14-Hz horizontal component geophones, coupled to steel plates. Reflected, refracted and surface arrivals resulting from a single shot of this seismic source are comparable in signal, noise, and frequency composition to three stacked hammer blows to a ground-planted stationary target.

Pressure-Induced Foaming of Metals

NASA Astrophysics Data System (ADS)

García-Moreno, Francisco; Mukherjee, Manas; Jiménez, Catalina; Banhart, John

2015-05-01

Pressure-induced foaming (PIF) of metals is a foaming technique in which blowing agent free compacted metal powders are foamed. The method consists of heating hot-compacted metallic precursors to above their melting temperature under gas overpressure and foaming them by pressure release. This study focuses on PIF of Al99.7 and AlSi7 alloys under both air or Ar and overpressures up to 9 bar. In situ x-ray radioscopy allows us to follow the foaming process and to perform quantitative analyses of expansion, foam morphology, and coalescence rate. Mass spectrometry helps to identify hydrogen as the foaming gas. Adsorbates on the former powder particles are found to be the primary gas source. Various advantages of this new method are identified and discussed.

High Resolution Far Infrared Spectroscopy of HFC-134a at Cold Temperatures

NASA Astrophysics Data System (ADS)

Wong, Andy; Medcraft, Chris; Thompson, Christopher; Robertson, Evan Gary; Appadoo, Dominique; McNaughton, Don

2016-06-01

Since the signing of the Montreal protocol, long-lived chlorofluorocarbons have been banned due to their high ozone depleting potential. In order to minimise the effect of such molecules, hydrofluorocarbons (HFCs) were synthesized as replacement molecules to be used as refrigerants and foam blowing agents. HFC-134a, or 1,1,1,2-tetrafluoroethane, is one of these molecules. Although HFCs do not cause ozone depletion, they are typically strong absorbers within the 10 micron atmospheric window, which lead to high global warming potentials. A high resolution FT-IR analysis of the νb{8} band (near 665 wn) of HFC-134a has been performed to help understand the intermode coupling between the νb{8} vibrational state and unobserved dark states.

Numerical study of blow-up and stability of line solitons for the Novikov-Veselov equation

NASA Astrophysics Data System (ADS)

Kazeykina, Anna; Klein, Christian

2017-07-01

We study numerically the evolution of perturbed Korteweg-de Vries solitons and of well localized initial data by the Novikov-Veselov (NV) equation at different levels of the ‘energy’ parameter E. We show that as \\vert E\\vert \\to ∞ , NV behaves, as expected, similarly to its formal limit, the Kadomtsev-Petviashvili equation. However at intermediate regimes, i.e. when \\vert E \\vert is not very large, more varied scenarios are possible, in particular, blow-ups are observed. The mechanism of the blow-up is studied.

V/STOL aircraft and method

DOEpatents

Owens, Phillip R.

1997-01-01

Aircraft apparatus and method capable of V/STOL (vertical, short takeoff and landing) in addition to conventional flight. For V/STOL operation, induced lift is provided by blowing air over the upper surface of each wing through a duct installed near the leading edge. Intake air is supplied to the blowing fan through a duct installed near the trailing edge, thus providing suction as well as blowing. Two fans in series are required. The engine provides power not only to the propeller but also to a transmission which provides power to the pulleys driving the belt-driven fans.

NASA RapidScat Observes El Nino Blowing in the Winds

NASA Image and Video Library

2016-01-21

While El Niño events have a significant impact on the entire Earth System, they are most easily visible in measurements of sea surface temperature (SST), sea surface height (SSH) and ocean winds near the surface. In fact, the precursor and the main driver of El Niño events is manifested in the weakening of the normally westward blowing trade winds, or even their complete reversal to blow from west to east, in the Western and Central tropical Pacific. http://photojournal.jpl.nasa.gov/catalog/PIA20365

Global solutions and finite time blow-up for fourth order nonlinear damped wave equation

NASA Astrophysics Data System (ADS)

Xu, Runzhang; Wang, Xingchang; Yang, Yanbing; Chen, Shaohua

2018-06-01

In this paper, we study the initial boundary value problem and global well-posedness for a class of fourth order wave equations with a nonlinear damping term and a nonlinear source term, which was introduced to describe the dynamics of a suspension bridge. The global existence, decay estimate, and blow-up of solution at both subcritical (E(0) < d) and critical (E(0) = d) initial energy levels are obtained. Moreover, we prove the blow-up in finite time of solution at the supercritical initial energy level (E(0) > 0).

77 FR 59683 - Northern Trust Investments, Inc., et al.; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-28

... handled. Such changes would not take effect until the Index Provider has given (a) the Calculation Agent... Provider will enter into an agreement (``Calculation Agent Agreement'') with a third party to act as ``Calculation Agent.'' The Calculation Agent will be solely responsible for the calculation and maintenance of...

Sales of veterinary antibacterial agents in nine European countries during 2005-09: trends and patterns.

PubMed

Grave, Kari; Greko, Christina; Kvaale, Mari K; Torren-Edo, Jordi; Mackay, David; Muller, Arno; Moulin, Gerard

2012-12-01

To identify trends and patterns of sales of veterinary antimicrobial agents in nine European countries during 2005-09 in order to document the situation. Existing sales data, in tonnes of active ingredients, of veterinary antimicrobial agents by class were collected from nine European countries in a standardized manner for the years 2005-09 (one country for 2006-09). A population correction unit (PCU) is introduced as a proxy for the animal population potentially treated with antimicrobial agents. The sales data are expressed as mg of active substance/PCU. Data coverage was reported to be 98%-100% for the nine countries. Overall, sales of veterinary antimicrobials agents, in mg/PCU, declined during the reporting period in the nine countries. Substantial differences in the sales patterns and in the magnitude of sales of veterinary antimicrobial agents, expressed as mg/PCU, between the nine countries are observed. The major classes sold were penicillins, sulphonamides and tetracyclines. The sales accounted for by the various veterinary antimicrobial agents have changed substantially for most countries. An increase in the sales of third- and fourth-generation cephalosporins and fluoroquinolones were observed for the majority of the countries. Through re-analysis of existing data by application of a harmonized approach, an overall picture of the trends in the sales of veterinary antimicrobial agents in the nine countries was obtained. Notable differences in trends in sales between the countries were observed. Further studies, preferably including data by animal species, are needed to understand the factors that explain these observations.

Microbial effects on the development of forensically important blow fly species.

PubMed

Crooks, Esther R; Bulling, Mark T; Barnes, Kate M

2016-09-01

Colonisation times and development rates of specific blow fly species are used to estimate the minimum Post Mortem Interval (mPMI). The presence or absence of bacteria on a corpse can potentially affect the development and survival of blow fly larvae. Therefore an understanding of microbial-insect interactions is important for improving the interpretation of mPMI estimations. In this study, the effect of two bacteria (Escherichia coli and Staphylococcus aureus) on the growth rate and survival of three forensically important blow fly species (Lucilia sericata, Calliphora vicina and Calliphora vomitoria) was investigated. Sterile larvae were raised in a controlled environment (16:8h day: night light cycle, 23:21°C day: night temperature cycle and a constant 35% relative humidity) on four artificial diets prepared with 100μl of 10(5) CFU bacterial solutions as follows: (1) E. coli, (2) S. aureus, (3) a 50:50 E. coli:S. aureus mix and (4) a sterile bacteria-free control diet. Daily measurements (length, width and weight) were taken from first instar larvae through to the emergence of adult flies. Survival rates were also determined at pupation and adult emergence. Results indicate that bacteria were not essential for the development of any of the blow fly species. However, larval growth rates were affected by bacterial diet, with effects differing between blow fly species. Peak larval weights also varied according to species-diet combination; C. vomitoria had the largest weight on E. coli and mixed diets, C. vicina had the largest weight on S. aureus diets, and treatment had no significant effect on the peak larval weight of L. sericata. These results indicate the potential for the bacteria that larvae are exposed to during development on a corpse to alter both developmental rates and larval weight in some blow fly species. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Preliminary assessment of a previously unknown fault zone beneath the Daytona Beach sand blow cluster near Marianna, Arkansas

USGS Publications Warehouse

Odum, Jackson K.; Williams, Robert; Stephenson, William J.; Tuttle, Martitia P.; Al-Shukri, Hadar

2016-01-01

We collected new high‐resolution P‐wave seismic‐reflection data to explore for possible faults beneath a roughly linear cluster of early to mid‐Holocene earthquake‐induced sand blows to the south of Marianna, Arkansas. The Daytona Beach sand blow deposits are located in east‐central Arkansas about 75 km southwest of Memphis, Tennessee, and about 80 km south of the southwestern end of the New Madrid seismic zone (NMSZ). Previous studies of these sand blows indicate that they were produced between 10,500 and 5350 yr B.P. (before A.D. 1950). The sand blows are large and similar in size to those in the heart of the NMSZ produced by the 1811–1812 earthquakes. The seismic‐reflection profiles reveal a previously unknown zone of near‐vertical faults imaged in the 100–1100‐m depth range that are approximately coincident with a cluster of earthquake‐induced sand blows and a near‐linear surface lineament composed of air photo tonal anomalies. These interpreted faults are expressed as vertical discontinuities with the largest displacement fault showing about 40 m of west‐side‐up displacement at the top of the Paleozoic section at about 1100 m depth. There are about 20 m of folding on reflections within the Eocene strata at 400 m depth. Increasing fault displacement with depth suggests long‐term recurrent faulting. The imaged faults within the vicinity of the numerous sand blow features could be a causative earthquake source, although it does not rule out the possibility of other seismic sources nearby. These newly located faults add to a growing list of potentially active Pleistocene–Holocene faults discovered over the last two decades that are within the Mississippi embayment region but outside of the historical NMSZ.

Earthquake-induced liquefaction features in the coastal setting of South Carolina and in the fluvial setting of the New Madrid seismic zone

USGS Publications Warehouse

Obermeier, S.F.; Jacobson, R.B.; Smoot, J.P.; Weems, R.E.; Gohn, G.S.; Monroe, J.E.; Powars, D.S.

1990-01-01

Many types of liquefaction-related features (sand blows, fissures, lateral spreads, dikes, and sills) have been induced by earthquakes in coastal South Carolina and in the New Madrid seismic zone in the Central United States. In addition, abundant features of unknown and nonseismic origin are present. Geologic criteria for interpreting an earthquake origin in these areas are illustrated in practical applications; these criteria can be used to determine the origin of liquefaction features in many other geographic and geologic settings. In both coastal South Carolina and the New Madrid seismic zone, the earthquake-induced liquefaction features generally originated in clean sand deposits that contain no or few intercalated silt or clay-rich strata. The local geologic setting is a major influence on both development and surface expression of sand blows. Major factors controlling sand-blow formation include the thickness and physical properties of the deposits above the source sands, and these relationships are illustrated by comparing sand blows found in coastal South Carolina (in marine deposits) with sand blows found in the New Madrid seismic zone (in fluvial deposits). In coastal South Carolina, the surface stratum is typically a thin (about 1 m) soil that is weakly cemented with humate, and the sand blows are expressed as craters surrounded by a thin sheet of sand; in the New Madrid seismic zone the surface stratum generally is a clay-rich deposit ranging in thickness from 2 to 10 m, in which case sand blows characteristically are expressed as sand mounded above the original ground surface. Recognition of the various features described in this paper, and identification of the most probable origin for each, provides a set of important tools for understanding paleoseismicity in areas such as the Central and Eastern United States where faults are not exposed for study and strong seismic activity is infrequent.

Iowa's cooperative snow fence program.

DOT National Transportation Integrated Search

2005-06-01

While we cant keep it from blowing, there are ways to influence the wind that carries tons : of blowing and drifting snow. Periodically, severe winter storms will create large snow : drifts that close roads and driveways, isolate farmsteads and in...

Gradient flows without blow-up for Lefschetz thimbles

DOE PAGES

Tanizaki, Yuya; Nishimura, Hiromichi; Verbaarschot, Jacobus J. M.

2017-10-16

We propose new gradient flows that define Lefschetz thimbles and do not blow up in a finite flow time. Here, we study analytic properties of these gradient flows, and confirm them by numerical tests in simple examples.

Free-Flight Evaluation of Forebody Blowing for Yaw Control at High Angels of Attack

NASA Technical Reports Server (NTRS)

Kiddy, Jason

1995-01-01

Forebody blowing is a concept developed to provide yaw control for aircraft flying at high angles of attack where a conventional rudder becomes ineffective. The basic concept is fairly simple. A small jet of air is forced out of the nose of the aircraft. This jet causes a repositioning of the forebody vortices in an asymmetrical fashion. The asymmetric forebody vortex flows develop a side force on the forebody which results in substantial yawing moments at high angles of attack. The purpose of this project was to demonstrate the use of forebody blowing as a control device through free-flight evaluation. This unique type of testing was performed at the NASA-Langley 30- by 60-foot tunnel. From these tests, it could then be shown that forebody blowing is an effective method of maintaining yaw control at high angles of attack.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawellek, Nicole; Krivov, Alexander V.; Marshall, Jonathan P.

The radii of debris disks and the sizes of their dust grains are important tracers of the planetesimal formation mechanisms and physical processes operating in these systems. Here we use a representative sample of 34 debris disks resolved in various Herschel Space Observatory (Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA) programs to constrain the disk radii and the size distribution of their dust. While we modeled disks with both warm and cold components, and identified warm inner disks around about two-thirds of the stars, we focusmore » our analysis only on the cold outer disks, i.e., Kuiper-belt analogs. We derive the disk radii from the resolved images and find a large dispersion for host stars of any spectral class, but no significant trend with the stellar luminosity. This argues against ice lines as a dominant player in setting the debris disk sizes, since the ice line location varies with the luminosity of the central star. Fixing the disk radii to those inferred from the resolved images, we model the spectral energy distribution to determine the dust temperature and the grain size distribution for each target. While the dust temperature systematically increases toward earlier spectral types, the ratio of the dust temperature to the blackbody temperature at the disk radius decreases with the stellar luminosity. This is explained by a clear trend of typical sizes increasing toward more luminous stars. The typical grain sizes are compared to the radiation pressure blowout limit s {sub blow} that is proportional to the stellar luminosity-to-mass ratio and thus also increases toward earlier spectral classes. The grain sizes in the disks of G- to A-stars are inferred to be several times s {sub blow} at all stellar luminosities, in agreement with collisional models of debris disks. The sizes, measured in the units of s {sub blow}, appear to decrease with the luminosity, which may be suggestive of the disk's stirring level increasing toward earlier-type stars. The dust opacity index β ranges between zero and two, and the size distribution index q varies between three and five for all the disks in the sample.« less

Looking into the puparium: Micro-CT visualization of the internal morphological changes during metamorphosis of the blow fly, Calliphora vicina, with the first quantitative analysis of organ development in cyclorrhaphous dipterans.

PubMed

Martín-Vega, Daniel; Simonsen, Thomas J; Hall, Martin J R

2017-05-01

Metamorphosis of cyclorrhaphous flies takes place inside a barrel-like puparium, formed by the shrinking, hardening and darkening of the third-instar larval cuticle. The opacity of this structure hampers the visualization of the morphological changes occurring inside and therefore a full understanding of the metamorphosis process. Here, we use micro-computed tomography (micro-CT) to describe the internal morphological changes that occur during metamorphosis of the blow fly, Calliphora vicina Robineau-Desvoidy 1830 (Diptera: Calliphoridae) at a greater temporal resolution than anything hitherto published. The morphological changes were documented at 10% intervals of the total intra-puparial period, and down to 2.5% intervals during the first 20% interval, when the most dramatic morphological changes occur. Moreover, the development of an internal gas bubble, which plays an essential role during early metamorphosis, was further investigated with X-ray images and micro-CT virtual sections. The origin of this gas bubble has been largely unknown, but micro-CT virtual sections show that it is connected to one of the main tracheal trunks. Micro-CT virtual sections also provided enough resolution for determining the completion of the larval-pupal and pupal-adult apolyses, thus enabling an accurate timing of the different intra-puparial life stages. The prepupal, pupal, and pharate adult stages last for 7.5%, 22.5%, and 70% of the total intra-puparial development, respectively. Furthermore, we provide for the first time quantitative data on the development of two organ systems of the blow fly: the alimentary canal and the indirect flight muscles. There is a significant and negative correlation between the volume of the indirect flight muscles and the pre-helicoidal region of the midgut during metamorphosis. The latter occupies a large portion of the thorax during the pupal stage but narrows progressively as the indirect flight muscles increase in volume during the development of the pharate adult. © 2017 The Authors Journal of Morphology Published by Wiley Periodicals, Inc.

Vaccinia Virus Vaccines: Past, Present and Future

PubMed Central

Jacobs, Bertram L.; Langland, Jeffrey O.; Kibler, Karen V.; Denzler, Karen L.; White, Stacy D.; Holechek, Susan A.; Wong, Shukmei; Huynh, Trung; Baskin, Carole R.

2009-01-01

Vaccinia virus (VACV) has been used more extensively for human immunization than any other vaccine. For almost two centuries, VACV was employed to provide cross-protection against variola virus, the causative agent of smallpox, until the disease was eradicated in the late 1970s. Since that time, continued research on VACV has produced a number of modified vaccines with improved safety profiles. Attenuation has been achieved through several strategies, including sequential passage in an alternative host, deletion of specific genes or genetic engineering of viral genes encoding immunomodulatory proteins. Some highly attenuated third- and fourth-generation VACV vaccines are now being considered for stockpiling against a possible re-introduction of smallpox through bioterrorism. Researchers have also taken advantage of the ability of the VACV genome to accommodate additional genetic material to produce novel vaccines against a wide variety of infectious agents, including a recombinant VACV encoding the rabies virus glycoprotein that is administered orally to wild animals. This review provides an in-depth examination of these successive generations of VACV vaccines, focusing on how the understanding of poxviral replication and viral gene function permits the deliberate modification of VACV immunogenicity and virulence. PMID:19563829

Plant terpenoids: acute toxicities and effects on flight motor activity and wing beat frequency in the blow fly Phaenicia sericata.

PubMed

Waliwitiya, Ranil; Belton, Peter; Nicholson, Russell A; Lowenberger, Carl A

2012-02-01

We evaluated the acute toxicities and the physiological effects of plant monoterpenoids (eugenol, pulegone, citronellal and alpha-terpineol) and neuroactive insecticides (malathion, dieldrin and RH3421) on flight muscle impulses (FMI) and wing beat signals (WBS) of the blow fly (Phaenicia sericata). Topically-applied eugenol, pulegone, citronellal, and alpha-terpineol produced neurotoxic symptoms, but were less toxic than malathion, dieldrin, or RH3421. Topical application of eugenol, pulegone, and citronellal reduced spike amplitude in one of the two banks of blow fly dorsolongitudinal flight muscles within 6-8 min, but with citronellal, the amplitude of FMIs reverted to a normal pattern within 1 hr. In contrast to pulegone and citronellal, where impulse frequency remained relatively constant, eugenol caused a gradual increase, then a decline in the frequency of spikes in each muscle bank. Wing beating was blocked permanently within 6-7 min of administering pulegone or citronellal and within 16 mins with eugenol. alpha-Terpineol-treated blow flies could not beat their wings despite normal FMI patterns. The actions of these monoterpenoids on blow fly flight motor patterns are discussed and compared with those of dieldrin, malathion, RH3421, and a variety of other neuroactive substances we have previously investigated in this system. Eugenol, pulegone and citronellal readily penetrate blow fly cuticle and interfere with flight muscle and/or central nervous function. Although there were differences in the effects of these compounds, they mainly depressed flight-associated responses, and acted similarly to compounds that block sodium channels and facilitate GABA action.

Comparison of several asphalt design methods.

DOT National Transportation Integrated Search

1998-01-01

This laboratory study compared several methods of selecting the optimum asphalt content of surface mixes. Six surface mixes were tested using the 50-blow Marshall design, the 75-blow Marshall design, two brands of SHRP gyratory compactors, and the U....

Influence of in-hole roughness and high freestream turbulence on film cooling from a shaped hole

NASA Astrophysics Data System (ADS)

Schroeder, Robert P.

Gas turbines are heavily used for electricity generation and aircraft propulsion with a strong desire in both uses to maximize thermal efficiency while maintaining reasonable power output. As a consequence, gas turbines run at high turbine inlet temperatures that require sophisticated cooling technologies to ensure survival of turbine components. One such technology is film cooling with shaped holes, where air is withdrawn from latter stages of the compressor, is bypassed around the combustor, and is eventually ejected out holes in turbine component surfaces. Air ejected from these shaped holes helps maintain components at temperatures lower than flow from the combustor. Many studies have investigated different factors that influence shaped hole performance. However, no studies in open literature have investigated how cooling performance is affected by roughness along interior walls of the shaped hole. The effect of in-hole roughness on shaped hole film cooling was the focus of this research. Investigation of in-hole roughness effects first required the determination of behavior for a shaped hole with smooth walls. A public shaped hole, now used by other investigators as well, was designed with a diffused outlet having 7º expansion angles and an area ratio of 2.5. At low freestream turbulence intensity of 0.5%, film cooling adiabatic effectiveness for this smooth hole was found to peak at a blowing ratio of 1.5. Measurements of flowfields and thermal fields revealed causes of this behavior. Blowing ratio increases above 1.5 caused the jet from the smooth hole to penetrate higher into the surrounding mainstream, exhibit a stronger counter-rotating vortex pair, and have narrower contact with the wall than at lower blowing ratios. Experiments performed at high freestream turbulence intensity of 13% revealed dynamics of how freestream turbulence both diluted and laterally spread coolant. At the high blowing ratio of 3 the dilution and spreading were competing effects, such that elevated freestream turbulence did not cause a decrease in area-averaged effectiveness. At the blowing ratio of 1.5, high freestream turbulence caused area-averaged effectiveness to decrease 17% relative to the low freestream turbulence case. Film cooling performance was measured for the shaped hole geometry with several different configurations of in-hole roughness. At low freestream turbulence intensity, in hole roughness caused decreases in area-averaged adiabatic effectiveness up to 61% relative to the smooth hole performance. These percent decreases in adiabatic effectiveness were more severe with increasing roughness levels and with increasing blowing ratios. Flowfield and thermal field measurements for the configuration with largest roughness size showed that the decrease in adiabatic effectiveness for rough holes as compared to smooth holes was due to thicker boundary layers along the interior walls of the cooling holes. The thicker boundary layers resulted in faster jet core flow, which in turn caused increased penetration of coolant into the mainstream and increased turbulence intensity inside the jet, with both leading to reduced adiabatic effectiveness. Detrimental effects of in-hole roughness persisted at the high freestream turbulence conditions as well.

Fabrication of Aluminum Tubes Filled with Aluminum Alloy Foam by Friction Welding.

PubMed

Hangai, Yoshihiko; Nakano, Yukiko; Koyama, Shinji; Kuwazuru, Osamu; Kitahara, Soichiro; Yoshikawa, Nobuhiro

2015-10-23

Aluminum foam is usually used as the core of composite materials by combining it with dense materials, such as in Al foam core sandwich panels and Al-foam-filled tubes, owing to its low tensile and bending strengths. In this study, all-Al foam-filled tubes consisting of ADC12 Al-Si-Cu die-cast aluminum alloy foam and a dense A1050 commercially pure Al tube with metal bonding were fabricated by friction welding. First, it was found that the ADC12 precursor was firmly bonded throughout the inner wall of the A1050 tube without a gap between the precursor and the tube by friction welding. No deformation of the tube or foaming of the precursor was observed during the friction welding. Next, it was shown that by heat treatment of an ADC12-precursor-bonded A1050 tube, gases generated by the decomposition of the blowing agent expand the softened ADC12 to produce the ADC12 foam interior of the dense A1050 tube. A holding time during the foaming process of approximately t H = 8.5 min with a holding temperature of 948 K was found to be suitable for obtaining a sound ADC12-foam-filled A1050 tube with sufficient foaming, almost uniform pore structures over the entire specimen, and no deformation or reduction in the thickness of the tube.

Electrodeposition of NiO films from various solvent electrolytic solutions for dye sensitized solar cell application

NASA Astrophysics Data System (ADS)

Koussi-Daoud, S.; Pellegrin, Y.; Odobel, F.; Viana, B.; Pauporté, T.

2017-02-01

We have investigated the preparation of NiO layers by cathodic electrodeposition in various organic-based solvents, namely ethanol, dimethyl sulfoxide (DMSO), DMSO/2 vol.% H2O and DMSO/25 vol.% H2O mixtures. The layers were formed from the electrochemical reduction of nickel nitrate precursor. We show that, depending on the solvent used, various nickel compounds were deposited. In the case of ethanol, a transparent precursor layer was obtained that was transformed into NiO after an annealing treatment at 300°C. For DMSO and DMSO with 2 volume % of H2O, adherent, well-covering, mesoporous and rather thick NiO layers were obtained after an annealing treatment at 450°C. These layers, after growth, contained nickel oxide or hydroxide, metallic nickel and DMSO. The solvent acted as a blowing agent, being included in the deposit and giving rise to a mesoporous film after its elimination by thermal annealing. These porous layers of p-type oxide have been successfully sensitized by a push-pull dye (P1 dye) and showed photocurrent generation and an open circuit voltage (Voc) up to 167 mV in p-type dye-sensitized solar cells (p-DSSCs). For DMSO with 25 volume % of H2O, the deposited layers contained more metallic nickel and were dense even after annealing. They were unsuitable in p-DSSCs.

Fabrication of Aluminum Tubes Filled with Aluminum Alloy Foam by Friction Welding

PubMed Central

Hangai, Yoshihiko; Nakano, Yukiko; Koyama, Shinji; Kuwazuru, Osamu; Kitahara, Soichiro; Yoshikawa, Nobuhiro

2015-01-01

Aluminum foam is usually used as the core of composite materials by combining it with dense materials, such as in Al foam core sandwich panels and Al-foam-filled tubes, owing to its low tensile and bending strengths. In this study, all-Al foam-filled tubes consisting of ADC12 Al-Si-Cu die-cast aluminum alloy foam and a dense A1050 commercially pure Al tube with metal bonding were fabricated by friction welding. First, it was found that the ADC12 precursor was firmly bonded throughout the inner wall of the A1050 tube without a gap between the precursor and the tube by friction welding. No deformation of the tube or foaming of the precursor was observed during the friction welding. Next, it was shown that by heat treatment of an ADC12-precursor-bonded A1050 tube, gases generated by the decomposition of the blowing agent expand the softened ADC12 to produce the ADC12 foam interior of the dense A1050 tube. A holding time during the foaming process of approximately tH = 8.5 min with a holding temperature of 948 K was found to be suitable for obtaining a sound ADC12-foam-filled A1050 tube with sufficient foaming, almost uniform pore structures over the entire specimen, and no deformation and minimum reduction in the thickness of the tube. PMID:28793629

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mondy, Lisa Ann; Rao, Rekha Ranjana; Shelden, Bion

We are developing computational models to elucidate the expansion and dynamic filling process of a polyurethane foam, PMDI. The polyurethane of interest is chemically blown, where carbon dioxide is produced via the reaction of water, the blowing agent, and isocyanate. The isocyanate also reacts with polyol in a competing reaction, which produces the polymer. Here we detail the experiments needed to populate a processing model and provide parameters for the model based on these experiments. The model entails solving the conservation equations, including the equations of motion, an energy balance, and two rate equations for the polymerization and foaming reactions,more » following a simplified mathematical formalism that decouples these two reactions. Parameters for the polymerization kinetics model are reported based on infrared spectrophotometry. Parameters describing the gas generating reaction are reported based on measurements of volume, temperature and pressure evolution with time. A foam rheology model is proposed and parameters determined through steady-shear and oscillatory tests. Heat of reaction and heat capacity are determined through differential scanning calorimetry. Thermal conductivity of the foam as a function of density is measured using a transient method based on the theory of the transient plane source technique. Finally, density variations of the resulting solid foam in several simple geometries are directly measured by sectioning and sampling mass, as well as through x-ray computed tomography. These density measurements will be useful for model validation once the complete model is implemented in an engineering code.« less

Channel-wing System for Thrust Deflection and Force/Moment Generation

NASA Technical Reports Server (NTRS)

Englar, Robert J. (Inventor); Bushnell, Dennis M. (Inventor)

2006-01-01

An aircraft comprising a Channel Wing having blown c h - ne1 circulation control wings (CCW) for various functions. The blown channel CCW includes a channel that has a rounded or near-round trailing edge. The channel further has a trailing-edge slot that is adjacent to the rounded trailing edge of the channel. The trailing-edge slot has an inlet connected to a source of pressurized air and is capable of tangentially discharging pressurized air over the rounded trailing edge. The aircraft further has a propeller that is located in the channel and ahead of the rounded trailing edge of the channel. The propeller provides a propeller thrust exhaust stream across the channel wing to propel the aircraft through the air and to provide high lift. The pressurized air being discharged over the rounded trailing edge provides a high lift that is obtained independent of an aircraft angle of attack, thus preventing the asymmetry. separated flow, and stall experienced by the CC wing at the high angle of attack it required for high lift generation. The aircraft can further include blown outboard circulation control wings (CCW) that are synergistically connected to the blown channel CCWs. The blown outboard CCWs provide additional high lift, control thrust/drag interchange, and can provide all three aerodynamic moments when differential blowing is applied front-to-rear or left-to-right. Both the blown channel CCW and the outboard CCW also have leading-edge blowing slots to prevent flow separation or to provide aerodynamic moments for control.

Characterization of carbon nanofibre-reinforced polypropylene foams.

PubMed

Antunes, M; Velasco, J I; Realinho, V; Arencón, D

2010-02-01

In this paper, carbon-nanofibre-reinforced polypropylene foams were prepared and characterized regarding their foaming behaviour, cellular structure and both thermo-mechanical as well as electrical properties. Polypropylene (PP) nanocomposites containing 5, 10 and 20 wt% of carbon nanofibres (CNF) and a chemical blowing agent were prepared by melt-mixing inside a twin-screw extruder and subsequently water-cooled and pelletized. The extruded nanocomposites were later foamed using a one-step compression-moulding process. The thermo-mechanical properties of the CNF-reinforced PP foams were studied, analyzing the influence of the carbon nanofibres on the cellular structure and subsequent thermo-mechanical behaviour of the foams. Carbon nanofibres not only seemed to act as nucleating agents, reducing the average cell size of the foams and increasing their cell density for similar expansion ratios, but also helped produce mechanically-improved foams, even reaching for the 20 wt% CNF-reinforced ones a specific modulus around 1.2 GPa x cm3/g for densities as low as 300 kg/m3. An increasingly higher electrical conductivity was assessed for both the solids as well as the foams with increasing the amount of carbon nanofibres.

Exploratory development of foams from liquid crystal polymers

NASA Technical Reports Server (NTRS)

Chung, T. S.

1985-01-01

Two types of liquid crystal polymer (LCP) compositions were studied and evaluated as structural foam materials. One is a copolymer of 6-hydroxy-2-naphthoic acid, terephthalic acid, and p-acetoxyacetanilide (designed HNA/TA/AAA), and the other is a copolymer of p-hydroxybenzoic acid and 6-hydroxy-2-naphthoic acid (designated HBA/HNA). Experimental results showed that the extruded HNA/TA/AA foams have better mechanical quality and appearance than HBA/HNA foams. Heat treatment improved foam tensile strength and break elongation, but reduced their modulus. The injection molding results indicated that nitrogen foaming agents with a low-pressure process gave better void distribution in the injection molded LCP foams than those made by the conventional injection-molding machine and chemical blowing agents. However, in comparing LCP foams with other conventional plastic foams, HBA/HNA foams have better mechanical properties than foamed ABS and PS, but are comparable to PBT and inferior to polycarbonate foams, especially in heat-deflection temperature and impact resistance energy. These deficiencies are due to LCP molecules not having been fully oriented during the Union-Carbide low-pressure foaming process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zia-ul-Mustafa, M., E-mail: engr.ziamustafa@gmail.com; Ahmad, Faiz; Megat-Yusoff, Puteri S. M.

In this study, intumescent fire retardant coatings (IFRC) were developed to investigate the synergistic effects of reinforced mica and wollastonite fillers based IFRC towards heat shielding, char expansion, char composition and char morphology. Ammonium poly-phosphate (APP) was used as acid source, expandable graphite (EG) as carbon source, melamine as blowing agent, boric acid as additive and Hardener H-2310 polyamide amine in bisphenol A epoxy resin BE-188(BPA) was used as curing agent. Bunsen burner fire test was used for thermal performance according to UL-94 for 1 h. Field Emission Scanning Electron Microscopy (FESEM) was used to observe char microstructure. X-Ray Diffraction (XRD)more » and Fourier transform infrared spectroscopy (FTIR) were used to analyse char composition. The results showed that addition of clay filler in IFRC enhanced the fire protection performance of intumescent coating. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) results showed the presence of boron phosphate, silicon phosphate oxide, aluminium borate in the char that improved the thermal performance of intumescent fire retardant coating (IFRC). Resultantly, the presence of these developed compounds enhanced the Integrity of structural steel upto 500°C.« less

Integrating GIS and ABM to Explore Spatiotemporal Dynamics

NASA Astrophysics Data System (ADS)

Sun, M.; Jiang, Y.; Yang, C.

2013-12-01

Agent-based modeling as a methodology for the bottom-up exploration with the account of adaptive behavior and heterogeneity of system components can help discover the development and pattern of the complex social and environmental system. However, ABM is a computationally intensive process especially when the number of system components becomes large and the agent-agent/agent-environmental interaction is modeled very complex. Most of traditional ABM frameworks developed based on CPU do not have a satisfying computing capacity. To address the problem and as the emergence of advanced techniques, GPU computing with CUDA can provide powerful parallel structure to enable the complex simulation of spatiotemporal dynamics. In this study, we first develop a GPU-based ABM system. Secondly, in order to visualize the dynamics generated from the movement of agent and the change of agent/environmental attributes during the simulation, we integrate GIS into the ABM system. Advanced geovisualization technologies can be utilized for representing the spatiotemporal change events, such as proper 2D/3D maps with state-of-the-art symbols, space-time cube and multiple layers each of which presents pattern in one time-stamp, etc. Thirdly, visual analytics which include interactive tools (e.g. grouping, filtering, linking, etc.) is included in our ABM-GIS system to help users conduct real-time data exploration during the progress of simulation. Analysis like flow analysis and spatial cluster analysis can be integrated according to the geographical problem we want to explore.

Design integration and noise studies for jet STOL aircraft. Task 7A: Augmentor wing cruise blowing valveless system. Volume 1: System design and test integration

NASA Technical Reports Server (NTRS)

Roepcke, F. A.; Nickson, T. B.

1973-01-01

Exploratory design studies conducted to establish the configuration of an augmentor wing vruise blowing (valveless) system in a 150-passenger STOL airplane were reported in NASA CR-114570. Those studies have been updated to incorporate the results of static rig, flow duct, and wind tunnel tests. Minor adjustments in duct flow velocity, flap length, and blowing nozzle geometry were incorporated to provide airplane characteristics that minimize takeoff gross weight and achieve sideline noise objectives for an advanced commercial STOL airplane.

V/STOL aircraft and method

DOEpatents

Owens, P.R.

1997-11-18

Aircraft apparatus and method capable of V/STOL (vertical, short takeoff and landing) in addition to conventional flight are disclosed. For V/STOL operation, induced lift is provided by blowing air over the upper surface of each wing through a duct installed near the leading edge. Intake air is supplied to the blowing fan through a duct installed near the trailing edge, thus providing suction as well as blowing. Two fans in series are required. The engine provides power not only to the propeller but also to a transmission which provides power to the pulleys driving the belt-driven fans. 10 figs.

Seismotectonic implications of sand blows in the southern Mississippi Embayment

USGS Publications Warehouse

Cox, R.T.; Hill, A.A.; Larsen, D.; Holzer, T.; Forman, S.L.; Noce, T.; Gardner, C.; Morat, J.

2007-01-01

We explore seismically-induced sand blows from the southern Mississippi Embayment and their implications in resolving the question of near or distal epicentral source region. This was accomplished using aerial photography, field excavations, and cone penetration tests. Our analysis shows that three sand blow fields exhibit a distinct chronology of strong ground motion for the southern embayment: (1) The Ashley County, Arkansas sand blow field, near the Arkansas/Louisiana state border, experienced four Holocene sand venting episodes; (2) to the north, the Desha County field experienced at least three episodes of liquefaction; and (3) the Lincoln-Jefferson Counties field experienced at least one episode. Cone penetration tests (CPT) conducted in and between the sand blow fields suggest that the fields may not be distal liquefaction associated with New Madrid seismic zone earthquakes but rather are likely associated with strong earthquakes on local faults. This conclusion is consistent with the differences in timing of the southern embayment sand venting episodes and those in the New Madrid seismic zone. These results suggest that active tectonism and strong seismicity in intraplate North America may not be localized at isolated weak spots, but rather widespread on fault systems that are favorably oriented for slip in the contemporary stress field. ?? 2006 Elsevier B.V. All rights reserved.

Development of the Variable Atmosphere Testing Facility for Blow-Down Analysis of the Mars Hopper Prototype

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan D. Jerred; Robert C. O'Brien; Steven D. Howe

Recent developments at the Center for Space Nuclear Research (CSNR) on a Martian exploration probe have lead to the assembly of a multi-functional variable atmosphere testing facility (VATF). The VATF has been assembled to perform transient blow-down analysis of a radioisotope thermal rocket (RTR) concept that has been proposed for the Mars Hopper; a long-lived, long-ranged mobile platform for the Martian surface. This study discusses the current state of the VATF as well as recent blow-down testing performed on a laboratory-scale prototype of the Mars Hopper. The VATF allows for the simulation of Mars ambient conditions within the pressure vesselmore » as well as to safely perform blow-down tests through the prototype using CO2 gas; the proposed propellant for the Mars Hopper. Empirical data gathered will lead to a better understanding of CO2 behavior and will provide validation of simulation models. Additionally, the potential of the VATF to test varying propulsion system designs has been recognized. In addition to being able to simulate varying atmospheres and blow-down gases for the RTR, it can be fitted to perform high temperature hydrogen testing of fuel elements for nuclear thermal propulsion.« less

Simulation of the Two Stages Stretch-Blow Molding Process: Infrared Heating and Blowing Modeling

NASA Astrophysics Data System (ADS)

Bordival, M.; Schmidt, F. M.; Le Maoult, Y.; Velay, V.

2007-05-01

In the Stretch-Blow Molding (SBM) process, the temperature distribution of the reheated perform affects drastically the blowing kinematic, the bottle thickness distribution, as well as the orientation induced by stretching. Consequently, mechanical and optical properties of the final bottle are closely related to heating conditions. In order to predict the 3D temperature distribution of a rotating preform, numerical software using control-volume method has been developed. Since PET behaves like a semi-transparent medium, the radiative flux absorption was computed using Beer Lambert law. In a second step, 2D axi-symmetric simulations of the SBM have been developed using the finite element package ABAQUS®. Temperature profiles through the preform wall thickness and along its length were computed and applied as initial condition. Air pressure inside the preform was not considered as an input variable, but was automatically computed using a thermodynamic model. The heat transfer coefficient applied between the mold and the polymer was also measured. Finally, the G'sell law was used for modeling PET behavior. For both heating and blowing stage simulations, a good agreement has been observed with experimental measurements. This work is part of the European project "APT_PACK" (Advanced knowledge of Polymer deformation for Tomorrow's PACKaging).

77 FR 59225 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-26

...-17) requires approximately 477 registered transfer agents to conduct searches using third party... agencies with monitoring transfer agents and ensuring compliance with the rule. We estimate that the average number of hours necessary for each transfer agent to comply with Rule 17Ad-17 is five hours...

In vitro Comparative Evaluation of Tensile Bond Strength of 6(th), 7(th) and 8(th) Generation Dentin Bonding Agents.

PubMed

Kamble, Suresh S; Kandasamy, Baburajan; Thillaigovindan, Ranjani; Goyal, Nitin Kumar; Talukdar, Pratim; Seal, Mukut

2015-05-01

Newer dentin bonding agents were developed to improve the quality of composite restoration and to reduce time consumption in its application. The aim of the present study was to evaluate tensile bond strength of 6(th), 7(th) and 8(th) generation bonding agents by in vitro method. Selected 60 permanent teeth were assigned into 20 in each group (Group I: 6(th) generation bonding agent-Adper SE plus 3M ESPE, Group II: 7(th) generation bonding agent-G-Bond GC Corp Japan and Group III: 8(th) generation dentin adhesives-FuturaBond, DC, Voco, Germany). With high-speed diamond disc, coronal dentin was exposed, and selected dentin bonding agents were applied, followed by composite restoration. All samples were saved in saline for 24 h and tensile bond strength testing was done using a universal testing machine. The obtained data were tabulated and statistically analyzed using ANOVA test. The tensile bond strength readings for 6(th) generation bonding agent was 32.2465, for 7(th) generation was 31.6734, and for 8(th)-generation dentine bonding agent was 34.74431. The highest tensile bond strength was seen in 8(th) generation bonding agent compared to 6(th) and 7(th) generation bonding agents. From the present study it can be conclude that 8(th) generation dentine adhesive (Futura DC, Voco, Germany) resulted in highest tensile bond strength compared to 6(th) (Adper SE plus, 3M ESPE) and 7(th) generation (G-Bond) dentin bonding agents.

Smallpox vaccines: targets of protective immunity

PubMed Central

Moss, Bernard

2011-01-01

Summary The eradication of smallpox, one of the great triumphs of medicine, was accomplished through the prophylactic administration of live vaccinia virus, a comparatively benign relative of variola virus, the causative agent of smallpox. Nevertheless, recent fears that variola virus may be used as a biological weapon together with the present susceptibility of unimmunized populations have spurred the development of new generation vaccines that are safer than the original and can be produced by modern methods. Predicting the efficacy of such vaccines in the absence of human smallpox, however, depends on understanding the correlates of protection. This review outlines the biology of poxviruses with particular relevance to vaccine development, describes protein targets of humoral and cellular immunity, compares animal models of orthopoxvirus disease with human smallpox, and considers the status of second and third generation smallpox vaccines. PMID:21198662

Preparation of zein fibers using solution blow spinning method

USDA-ARS?s Scientific Manuscript database

Zein fibers were successfully fabricated via solution blow spinning (SBS) using acetic acid as solvent. Surface tension, viscosity and modulus of zein solutions were respectively determined by force tensiometer and rheometer. Increases of these properties were observed with an increase of concentrat...

The effect of the air-blowing step on the technique sensitivity of four different adhesive systems.

PubMed

Spreafico, Diego; Semeraro, Stefano; Mezzanzanica, Dario; Re, Dino; Gagliani, Massimo; Tanaka, Toru; Sano, Hidehiko; Sidhu, Sharanbir K

2006-03-01

To evaluate the technique sensitivity of four different adhesive systems using different air-blowing pressure. Four adhesive systems were employed: Clearfil SE Bond [SE] (Kuraray, Japan), G-Bond [GB] (GC Corporation, Japan), Adper Prompt L-Pop [LP] (3M ESPE, USA) and an experimental adhesive, SSB-200 [SSB] (Kuraray, Japan). Twenty-four extracted molars were used. After grinding the coronal enamel surface, the teeth were divided into two equal groups. The first group's teeth were randomly assigned for bonding with the different adhesives using gentle air-blowing (g). For the teeth of the second group, the four adhesive systems were applied using strong air-blowing (s). After storage overnight in 37 degrees C water, the bonded specimens were sectioned into sticks (1 mm x 1 mm wide), which were subjected to microtensile bond strength testing (microTBS) at a crosshead speed of 1 mm/min. The load at failure of each specimen was recorded and the data were analyzed by one-way ANOVA and Tukey HSD tests. The surfaces of the fractured specimens were observed using SEM to determine the failure mode. The results of the microTBS test showed that the highest bond strengths tended to be with SE for both gentle and strong air-blowing, and the significantly lowest for SSB with strong air streaming. Comparing the two techniques, significant differences were noted only for SSB-200 (P < 0.05). For each material, the SEM evaluation did not show distinct differences in the nature of the fractures between the two techniques, except for SSB-200. The adhesives tested are not technique sensitive, except SSB-200, with regards to the air-blowing step.

Optimization of bump and blowing to control the flow through a transonic compressor blade cascade

NASA Astrophysics Data System (ADS)

Mazaheri, K.; Khatibirad, S.

2018-03-01

Shock control bump (SCB) and blowing are two flow control methods, used here to improve the aerodynamic performance of transonic compressors. Both methods are applied to a NASA rotor 67 blade section and are optimized to minimize the total pressure loss. A continuous adjoint algorithm is used for multi-point optimization of a SCB to improve the aerodynamic performance of the rotor blade section, for a range of operational conditions around its design point. A multi-point and two single-point optimizations are performed in the design and off-design conditions. It is shown that the single-point optimized shapes have the best performance for their respective operating conditions, but the multi-point one has an overall better performance over the whole operating range. An analysis is given regarding how similarly both single- and multi-point optimized SCBs change the wave structure between blade sections resulting in a more favorable flow pattern. Interactions of the SCB with the boundary layer and the wave structure, and its effects on the separation regions are also studied. We have also introduced the concept of blowing for control of shock wave and boundary-layer interaction. A geometrical model is introduced, and the geometrical and physical parameters of blowing are optimized at the design point. The performance improvements of blowing are compared with the SCB. The physical interactions of SCB with the boundary layer and the shock wave are analyzed. The effects of SCB on the wave structure in the flow domain outside the boundary-layer region are investigated. It is shown that the effects of the blowing mechanism are very similar to the SCB.

Use of second-generation antipsychotic agents for sleep and sedation: a provider survey.

PubMed

Hermes, Eric D A; Sernyak, Michael; Rosenheck, Robert

2013-04-01

Anecdotal evidence suggests that second-generation antipsychotic agents are increasingly used to treat sleep problems. This study sought to quantify the proportion of new prescriptions for second-generation antipsychotic agents started for sleep/sedation and the correlates of such use. A cross-sectional survey of provider decision making at the time second-generation antipsychotic agents were prescribed, documenting the reasons for the medication, patient demographics, psychiatric and medical diagnoses, patient health characteristics, and provider background. A single Veterans Affairs Medical Center over a 20-month period. Prescribers of second-generation antipsychotic agents. N/A. Seven hundred seven (32.2%) of 2,613 surveys indicated sleep/sedation was at least one reason for using a second-generation anti-psychotic agent, whereas for 266 (12.1%) it was the only reason. Quetiapine was most frequently prescribed overall as well as for sleep/sedation (47.0% and 73.6% respectively). Second-generation antipsychotic agent use for sleep/sedation was unrelated to sociodemographic characteristics, least likely in patients with schizophrenia or bipolar disorder, and most likely as a newly started second-generation antipsychotic agent. Sleep/sedation is a common reason given for new prescriptions of second-generation antipsychotic agents. Quetiapine is most frequently used for this purpose. A greater understanding of why providers use second-generation antipsychotic agents rather than safer and less costly alternatives for sleep problems may advance the development of interventions to reduce adverse effects.

75 FR 22189 - Obtaining Information From the Postal Service

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-27

... rules governing (1) the issuance of subpoenas requiring officers, employees, agents, or contractors of... transmitted to third-party agents or contractors. Rule 14 is modified to revise the Postal Service's... officers and employees), to persons or entities currently acting as agents for the Postal Service, or to...

Antibiotic Use and Antimicrobial Resistance of Surgical Patients with Peritonitis at a Tertiary Referral Hospital in Rwanda.

PubMed

Rickard, Jennifer; Ngarambe, Christian; Ndayizeye, Leonard; Smart, Blair; Riviello, Robert; Majyambere, Jean Paul; Ghebre, Rahel G

There is growing recognition of the worsening problem of antibiotic resistance and the need for antibiotic stewardship in low-resource settings. The aim of this study was to describe antibiotic use and antimicrobial resistance in patients undergoing surgery for peritonitis at a Rwandan referral hospital. All surgical patients with peritonitis at a Rwandan referral hospital were enrolled. Prospective data were collected on epidemiology, clinical features, interventions, and outcomes. Antibiotic agents were prescribed and cultures were collected according to surgeon discretion. High risk for antibiotic treatment failure or death was defined as patients with severe sepsis, older than 70 years of age, tumor, or operating room delay more than 24 hours from hospital admission. Logistic regression was used to determine factors associated with high risk of antibiotic treatment failure or death. Over a six-month period, 280 patients underwent operation for peritonitis; 79 patients were excluded because no infectious etiology was identified at operation. Data on antibiotic usage were available for 165 patients. The most common diagnoses were intestinal obstruction (n = 43) and appendicitis (n = 36). Most patients received antibiotic agents, the most of of which being third-generation cephalosporins (n = 149; 90%) and metronidazole (n = 140; 85%). The mean duration of antibiotics was 5.1 days (range: 0-14). Overall, 80 (54%) patients were high-risk for antibiotic treatment failure or death. Risk for antibiotic treatment failure or death was associated with localized peritonitis (p = 0.001) and high American Society of Anesthesiologist score (p = 0.003). Cultures were collected from 33 patients and seven patients had an organism isolated. Escherichia coli was identified in in five surgical specimens and two 2 urine cultures. All Escherichia coli specimens showed resistance to cephalosporins. Broad antibiotic coverage with third-generation cephalosporins and metronidazole is common in Rwandan surgical patients with peritonitis. Areas for improvement should focus on choice and duration of antibiotic agents, tailored to underlying diagnosis and risk factors for antibiotic treatment failure or death. More data are needed on antibiotic resistance patterns to guide antimicrobial therapy.

CR-39 track etching and blow-up method

DOEpatents

Hankins, Dale E.

1987-01-01

This invention is a method of etching tracks in CR-39 foil to obtain uniformly sized tracks. The invention comprises a step of electrochemically etching the foil at a low frequency and a "blow-up" step of electrochemically etching the foil at a high frequency.

Designing, developing and implementing a living snow fence program for New York state.

DOT National Transportation Integrated Search

2015-07-01

Living snow fences (LSF) are a form of passive snow control designed to mitigate blowing and drifting snow problems : on roadways. Blowing and drifting snow can increase the cost of highway maintenance and create hazardous driving : conditions when s...

Solution blow spinning of food-grade gelatin nanofibers

USDA-ARS?s Scientific Manuscript database

The primary advantage of nanofibers over larger diameter fibers is the larger surface area to volume ratio. This study evaluated solution blow spinning (SBS) processing conditions for obtaining food-grade gelatin nanofibers from mammalian and fishery by-products, such as pork skin gelatins (PGs) and...

Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

USDA-ARS?s Scientific Manuscript database

Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

42. NORTHEAST VIEW OF BLOW ENGINE HOUSE No. 3, WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. NORTHEAST VIEW OF BLOW ENGINE HOUSE No. 3, WITH FILTER CAKE HOSUE IN CENTER FOREGROUND, AND EVAPORATIVE WASTE WATER TREATMENT COOLING TOWER TO THE LEFT. (Jet Lowe) - U.S. Steel Duquesne Works, Blast Furnace Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Proteus mirabilis interkingdom swarming signals attract blow flies

USDA-ARS?s Scientific Manuscript database

Flies transport specific bacteria with their larvae which provides a wider range of nutrients for those bacteria. Our hypothesis was that this symbiotic interaction may depend on interkingdom signaling. We obtained Proteus mirabilis from the salivary glands of the blow fly Lucilia sericat. This s...

Improved correlation between Texas cone penetrometer blow count and undrained shear strength of soft clays.

DOT National Transportation Integrated Search

2009-01-01

The objective of this project was to develop an improved correlation between Texas Cone Penetrometer (TCP) : blow count and undrained shear strength for soft, clay soils in the upper approximately 30 feet of the ground. Subsurface : explorations were...

Numerical modelling of heat transfer in a cavity due to liquid jet impingement for liquid supported stretch blow moulding

NASA Astrophysics Data System (ADS)

Smyth, Trevor; Menary, Gary; Geron, Marco

2018-05-01

Impingement of a liquid jet in a polymer cavity has been modelled numerically in this study. Liquid supported stretch blow moulding is a nascent polymer forming process using liquid as the forming medium to produce plastic bottles. The process derives from the conventional stretch blow moulding process which uses compressed air to deform the preform. Heat transfer away from the preform greatly increases when a liquid instead of a gas is flowing over a solid; in the blow moulding process the temperature of the preform is tightly controlled to achieve optimum forming conditions. A model was developed with Computational Fluid Dynamics code ANSYS Fluent which allows the extent of heat transfer between the incoming liquid and the solid preform to be determined in the initial transient stage, where a liquid jet enters an air filled preform. With this data, an approximation of the extent of cooling through the preform wall can be determined.

Suicide by blunt head trauma - Two cases with striking similarities.

PubMed

Park, Hyejin; Lee, Bongwoo; Yoon, Connie

2015-10-01

There have been several forensic pathological studies on the distinction between falls from height and homicidal blows in blunt head trauma, but few studies have focused on suicidal blows. Self-inflicted blunt head trauma is usually a part of a complex suicide with more than one suicidal method applied. Actually, no reports on suicide indicate blunt head trauma to be the singular cause of death in recent publications. Cases with self-inflicted blunt trauma are often challenging for those involved in the investigation because they are confronted with findings that are also found in homicides. A refined guideline to differentiate suicidal blows from homicidal blows in blunt head trauma allows for a more accurate representation of the events surrounding death. This paper presents two cases of suicide by self-inflicted blunt head trauma in which blunt head trauma from repeatedly hitting the decedent's head with a hammer was considered to be the only cause of death. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Integration Of Heat Transfer Coefficient In Glass Forming Modeling With Special Interface Element

NASA Astrophysics Data System (ADS)

Moreau, P.; César de Sá, J.; Grégoire, S.; Lochegnies, D.

2007-05-01

Numerical modeling of the glass forming processes requires the accurate knowledge of the heat exchange between the glass and the forming tools. A laboratory testing is developed to determine the evolution of the heat transfer coefficient in different glass/mould contact conditions (contact pressure, temperature, lubrication…). In this paper, trials are performed to determine heat transfer coefficient evolutions in experimental conditions close to the industrial blow-and-blow process conditions. In parallel of this work, a special interface element is implemented in a commercial Finite Element code in order to deal with heat transfer between glass and mould for non-meshing meshes and evolutive contact. This special interface element, implemented by using user subroutines, permits to introduce the previous heat transfer coefficient evolutions in the numerical modelings at the glass/mould interface in function of the local temperatures, contact pressures, contact time and kind of lubrication. The blow-and-blow forming simulation of a perfume bottle is finally performed to assess the special interface element performance.

Lattice enumeration for inverse molecular design using the signature descriptor.

PubMed

Martin, Shawn

2012-07-23

We describe an inverse quantitative structure-activity relationship (QSAR) framework developed for the design of molecular structures with desired properties. This framework uses chemical fragments encoded with a molecular descriptor known as a signature. It solves a system of linear constrained Diophantine equations to reorganize the fragments into novel molecular structures. The method has been previously applied to problems in drug and materials design but has inherent computational limitations due to the necessity of solving the Diophantine constraints. We propose a new approach to overcome these limitations using the Fincke-Pohst algorithm for lattice enumeration. We benchmark the new approach against previous results on LFA-1/ICAM-1 inhibitory peptides, linear homopolymers, and hydrofluoroether foam blowing agents. Software implementing the new approach is available at www.cs.otago.ac.nz/homepages/smartin.

Highly porous 3D nanofiber scaffold using an electrospinning technique.

PubMed

Kim, Geunhyung; Kim, WanDoo

2007-04-01

A successful 3D tissue-engineering scaffold must have a highly porous structure and good mechanical stability. High porosity and optimally designed pore size provide structural space for cell accommodation and migration and enable the exchange of nutrients between the scaffold and environment. Poly(epsilon-carprolactone) fibers were electrospun using an auxiliary electrode and chemical blowing agent (BA), and characterized according to porosity, pore size, and their mechanical properties. We also investigated the effect of the BA on the electrospinning processability. The growth characteristic of human dermal fibroblasts cells cultured in the webs showed the good adhesion with the blown web relative to a normal electrospun mat. The blown nanofiber web had good tensile properties and high porosity compared to a typical electrospun nanofiber scaffold. (c) 2006 Wiley Periodicals, Inc.

New Drugs and Novel Mechanisms of Action in Multiple Myeloma in 2013: A Report from the International Myeloma Working Group (IMWG)

PubMed Central

Ocio, EM; Richardson, PG; Rajkumar, SV; Palumbo, A; Mateos, MV; Orlowski, R; Kumar, S; Usmani, S; Roodman, D; Niesvizky, R; Einsele, H; Anderson, KC; Dimopoulos, MA; Avet-Loiseau, H; Mellqvist, UH; Turesson, I; Merlini, G; Schots, R; McCarthy, P; Bergsagel, L; Chim, J; Lahuerta, JJ; Shah, J; Reiman, A; Mikhael, J; Zweegman, S; Lonial, S; Comenzo, R; Chng, WJ; Moreau, P; Sonneveld, P; Ludwig, H; Durie, BGM; San Miguel, JF

2014-01-01

Treatment in medical oncology is gradually shifting from the use of non-specific chemotherapeutic agents towards an era of novel targeted therapy in which drugs and their combinations target specific aspects of the biology of tumor cells. Multiple myeloma (MM) has become one of the best examples in this regard, reflected in the identification of new pathogenic mechanisms, together with the development of novel drugs that are being explored from the preclinical setting to the early phases of clinical development. We review the biological rationale for the use of the most important new agents for treating MM and summarize their clinical activity in an increasingly busy field. First, we discuss data from already approved and active agents (including second- and third-generation- proteasome inhibitors, immunomodulatory agents (IMIDs) and alkylators). Then we focus on agents with novel mechanisms of action, such as monoclonal antibodies (MoAb), cell cycle specific drugs, deacetylase inhibitors, agents acting on the unfolded protein response, signaling transduction pathway inhibitors, and kinase inhibitors. Among this plethora of new agents or mechanisms some are specially promising: Anti-CD38 MoAb, such as daratumumab, are the first antibodies with clinical activity as single agents in MM. Also the kinesin spindle protein inhibitor Arry-520 is effective in monotherapy as well as in combination with dexamethasone in heavily pretreated patients. Immunotherapy against MM is also being explored, and probably the most attractive example of this approach is the combination of the anti-CS1 MoAb elotuzumab with lenalidomide and dexamethasone, that has produced exciting results in the relapsed/refractory setting. PMID:24253022

Application of Circulation Control Technology to Airframe Noise Reduction

NASA Technical Reports Server (NTRS)

Ahuja, K. K.; Sankar, L. N.; Englar, R. J.; Munro, Scott E.; Li, Yi; Gaeta, R. J.

2003-01-01

This report is a summary of the work performed by Georgia Tech Research Institute (GTRI) under NASA Langley Grant NAG-1-2146, which was awarded as a part of NASA's Breakthrough Innovative Technologies (BIT) initiative. This was a three-year program, with a one-year no-cost extension. Each year's study has been an integrated effort consisting of computational fluid dynamics, experimental aerodynamics, and detailed noise and flow measurements. Year I effort examined the feasibility of reducing airframe noise by replacing the conventional wing systems with a Circulation Control Wing (CCW), where steady blowing was used through the trailing edge of the wing over a Coanda surface. It was shown that the wing lift increases with CCW blowing and indeed for the same lift, a CCW wing was shown to produce less noise. Year 2 effort dealt with a similar study on the role of pulsed blowing on airframe noise. The main objective of this portion of the study was to assess whether pulse blowing from the trailing edge of a CCW resulted in more, less, or the same amount of radiated noise to the farfield. Results show that a reduction in farfield noise of up to 5 dB is measured when pulse flow is compared with steady flow for an equivalent lift configuration. This reduction is in the spectral region associated with the trailing edge jet noise. This result is due to the unique advantage that pulsed flow has over steady flow. For a range of frequencies, more lift is experienced with the same mass flow as the steady case. Thus, for an equivalent lift and slot height, the pulsed system can operate at lower jet velocities, and hence lower jet noise. The computational analysis showed that for a given time-averaged mass flow rate, pulsed jets give a higher value of C(sub l) and a higher L/D than equivalent steady jets. This benefit is attributable to higher instantaneous jet velocities, and higher instantaneous C(sub mu) values for the pulsed jet. Pulsed jet benefits increase at higher frequencies. However, these advantages are somewhat offset by the unsteadiness in the loads, which will cause structural vibrations and fatigue. Additional studies must be done, perhaps with multiple jets on the upper and lower surfaces, to smooth out the fluctuations in lift while retaining the benefits. The rest of the effort was devoted to examining ways of reducing flap edge noise by blowing air through a Coanda nozzle over a rounded tip of the flap. In this case, we were successful in moving the tip vortex away from the tip, but the device producing the blowing was noisy and we were unable to examine the noise benefits, although we believe that the movement of the tip vortex far from the tip should provide noise benefits. It should be noted that in an effort to understand the fluid dynamics and the aeroacoustics of a jet blowing over a Coanda surface, we also carried out a very extensive study of the high aspect ratio slot jets. A first-ever set of far-field noise spectra were measured for jets exhausting from slots with aspect ratios in the range 100 to 3000. Parallel measurements of velocity profiles, length scales and convection velocities were measured to understand the noise generation of high aspect ratio jets. Attempts were also made to develop jet noise prediction schemes for such jets. Much of the work done under this effort has been described in five conference papers and two doctoral theses. The first year s work on the use of steady blowing was described in two AIAA papers presented at the 2001 AIAA Aerospace Sciences Meeting in Reno. Subsequent work was presented at the 9th AIMCEAS Aeroacoustics Conference and Exhibit held at Hilton Head May 12-13. Another paper is to be presented at the 2004 AIAA Aerospace Sciences Meeting in Reno in January 2004. All six papers are included with this report as Appendices. The bulk of the experimental work done in an effort to produce a pulsed flow that is free of upstream noise is also attached as an Appendix.

Submerged Gas Jet Penetration: A Study of Bubbling Versus Jetting and Side Versus Bottom Blowing in Copper Bath Smelting

NASA Astrophysics Data System (ADS)

Kapusta, Joël P. T.

2017-06-01

Although the bottom blowing ShuiKouShan process has now been widely implemented in China, in both lead and copper smelters, some doubts, questions, and concerns still seem to prevail in the metallurgical community outside China. In the author's opinion, part of these doubts and concerns could be addressed by a better general understanding of key concepts of submerged gas injection, including gas jet trajectory and penetration, and the concept, application, and benefits of sonic injection in jetting regime. To provide some answers, this article first offers a discussion on the historical developments of the theory and mathematical characterization of submerged gas jet trajectory, including the proposed criteria for the transition from bubbling to jetting regime and the application of the Prandtl-Meyer theory to submerged gas jets. A second part is devoted to a quantitative study of submerged gas jet penetration in copper bath smelting, including a comparison between bubbling and jetting regimes, and side versus bottom blowing. In the specific cases studied, the calculated gas jet axis trajectory length in jetting regime is 159 cm for bottom blowing, whereas it varies between 129 and 168 cm for side blowing for inclination angles of +18° to -30° to the horizontal. This means that side blowing in the jetting regime would provide a deeper penetration and longer gas jet trajectory than generally obtained by conventional bath smelting vessels such as the Noranda and Teniente reactors. The theoretical results of this study do corroborate the successful high-intensity practice of the slag make converting process at Glencore Nickel in Canada that operates under high oxygen shrouded injection in the jetting regime, and this would then suggest that retrofitting conventional low-pressure, side-blowing tuyeres of bath smelting and converting reactors with sonic injectors in jetting regime certainly appears as a valuable option for process intensification with higher oxygen enrichment, without major process changes or large capital expenditure, i.e., no need for full reactor replacement.

Massive gravity and the suppression of anisotropies and gravitational waves in a matter-dominated contracting universe

NASA Astrophysics Data System (ADS)

Lin, Chunshan; Quintin, Jerome; Brandenberger, Robert H.

2018-01-01

We consider a modified gravity model with a massive graviton, but which nevertheless only propagates two gravitational degrees of freedom and which is free of ghosts. We show that non-singular bouncing cosmological background solutions can be generated. In addition, the mass term for the graviton prevents anisotropies from blowing up in the contracting phase and also suppresses the spectrum of gravitational waves compared to that of the scalar cosmological perturbations. This addresses two of the main problems of the matter bounce scenario.

Electrostatically focused addressable field emission array chips (AFEA's) for high-speed massively parallel maskless digital E-beam direct write lithography and scanning electron microscopy

DOEpatents

Thomas, Clarence E.; Baylor, Larry R.; Voelkl, Edgar; Simpson, Michael L.; Paulus, Michael J.; Lowndes, Douglas H.; Whealton, John H.; Whitson, John C.; Wilgen, John B.

2002-12-24

Systems and methods are described for addressable field emission array (AFEA) chips. A method of operating an addressable field-emission array, includes: generating a plurality of electron beams from a pluralitly of emitters that compose the addressable field-emission array; and focusing at least one of the plurality of electron beams with an on-chip electrostatic focusing stack. The systems and methods provide advantages including the avoidance of space-charge blow-up.

Crew Earth Observations (CEO) taken during Expedition Five on the ISS

NASA Image and Video Library

2002-08-25

ISS005-E-11189 (25 August 2002) --- Calanscio Sand Sea, Libya is featured in this digital image photographed by an Expedition 5 crewmember on the International Space Station (ISS). A plume of black smoke blowing westward is silhouetted against yellow linear dunes in the great sand sea of northeast Libya. Smoke from flares at remote well heads is commonly seen by astronauts flying over the Sahara Desert. NASA scientists studying the Station imagery had the following observations about the image. The plume dispersal pattern visible at the left edge of the image may be due to upper-level winds or gravitational settling of heavier particulates. The regular pattern of linear dunes is generated by two major winds: the dominant north wind (north is towards the top right) determines the orientation of the sand dunes. Gentler easterly winds, as were blowing when this view was taken, make the dunes asymmetric, with a gentle windward (west) slope and an over steeped downwind slope. Some over steepened slopes even cast shadows in the early morning light. One mound of sand (top right), due north of the well head, does not fit the pattern of linear dunes. This type is known as a star dune.

A computer program for calculating symmetrical aerodynamic characteristics and lateral-directional stability derivatives of wing-body combinations with blowing jets

NASA Technical Reports Server (NTRS)

Lan, C. E.; Mehrotra, S. C.; Fox, C. H., Jr.

1978-01-01

The necessary information for using a computer program to calculate the aerodynamic characteristics under symmetrical flight conditions and the lateral-directional stability derivatives of wing-body combinations with upper-surface-blowing (USB) or over-wing-blowing (OWB) jets are described. The following new features were added to the program: (1) a fuselage of arbitrary body of revolution has been included. The effect of wing-body interference can now be investigated, and (2) all nine lateral-directional stability derivatives can be calculated. The program is written in FORTRAN language and runs on CDC Cyber 175 and Honeywell 66/60 computers.

Vortex-generating coolant-flow-passage design for increased film-cooling effectiveness and surface coverage

NASA Astrophysics Data System (ADS)

Papell, S. S.

1984-11-01

The thermal film-cooling footprints observed by infrared imagery for three coolant-passage configurations embedded in adiabatic-test plates are discussed. The configurations included a standard round-hole cross section and two orientations of a vortex-generating flow passage. Both orientations showed up to factors of four increases in both film-cooling effectiveness and surface coverage over that obtained with the round coolant passage. The crossflow data covered a range of tunnel velocities from 15.5 to 45 m/sec with blowing rates from 0.20 to 2.05. A photographic streakline flow visualization technique supported the concept of the counterrotating apability of the flow passage design and gave visual credence to its role in inhibiting flow separation.

Vortex-generating coolant-flow-passage design for increased film-cooling effectiveness and surface coverage

NASA Technical Reports Server (NTRS)

Papell, S. S.

1984-01-01

The thermal film-cooling footprints observed by infrared imagery for three coolant-passage configurations embedded in adiabatic-test plates are discussed. The configurations included a standard round-hole cross section and two orientations of a vortex-generating flow passage. Both orientations showed up to factors of four increases in both film-cooling effectiveness and surface coverage over that obtained with the round coolant passage. The crossflow data covered a range of tunnel velocities from 15.5 to 45 m/sec with blowing rates from 0.20 to 2.05. A photographic streakline flow visualization technique supported the concept of the counterrotating apability of the flow passage design and gave visual credence to its role in inhibiting flow separation.

27 CFR 70.302 - Fees and costs for witnesses.

Code of Federal Regulations, 2014 CFR

2014-04-01

... issued, or an officer, employee, agent, accountant, or attorney of that person. (5) Third party records. Third party records are books, papers, records, or other data in which the person with respect to whose...

27 CFR 70.302 - Fees and costs for witnesses.

Code of Federal Regulations, 2012 CFR

2012-04-01

... issued, or an officer, employee, agent, accountant, or attorney of that person. (5) Third party records. Third party records are books, papers, records, or other data in which the person with respect to whose...

27 CFR 70.302 - Fees and costs for witnesses.

Code of Federal Regulations, 2013 CFR

2013-04-01

... issued, or an officer, employee, agent, accountant, or attorney of that person. (5) Third party records. Third party records are books, papers, records, or other data in which the person with respect to whose...

Blow-up in nonlinear models of extended particles with confined constituents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alvarez, A.; Ranada, A.F.

1988-11-15

It is shown that the indefinite character of the charge in classical models of extended particles with confined constituents is a serious handicap since infinite amounts of positive and negative charge can be emitted in some solutions, causing a blow-up in finite time.

A Molecular Key for the Identification of Blow Flies in Southeastern Nebraska

USDA-ARS?s Scientific Manuscript database

The identification of blow flies (Calliphoridae) (typically the first colonizers of cadavers) is difficult, especially in the earlier instars because of their small size, similarity and simplicity in external morphology. We consider how taxonomic keys based on molecular genetic data facilitate accur...

Correlation of the manual compaction hammer with mechanical hammers for the Marshall method of design for asphaltic concrete.

DOT National Transportation Integrated Search

1964-09-01

The purpose of this investigation was to establish, through a series of correlations, the compactive effort (number of blows) needed using the mechanical hammers to yield similar physical properties obtained with 75 blows of the manual hammer.

Preparation of fish skin gelatin-based nanofibers incorporating cinnamaldehyde by solution blow spinning

USDA-ARS?s Scientific Manuscript database

Cinnamaldehyde, a natural preservative that can non-specifically deactivate foodborne pathogens, was successfully incorporated into fish skin gelatin (FSG) solutions and blow spun into uniform nanofibers. The effects of cinnamaldehyde ratios (5-30%, w/w FSG) on physicochemical properties of fiber-fo...

Biomechanical correlates of symptomatic and asymptomatic neurophysiological impairment in high school football.

PubMed

Breedlove, Evan L; Robinson, Meghan; Talavage, Thomas M; Morigaki, Katherine E; Yoruk, Umit; O'Keefe, Kyle; King, Jeff; Leverenz, Larry J; Gilger, Jeffrey W; Nauman, Eric A

2012-04-30

Concussion is a growing public health issue in the United States, and chronic traumatic encephalopathy (CTE) is the chief long-term concern linked to repeated concussions. Recently, attention has shifted toward subconcussive blows and the role they may play in the development of CTE. We recruited a cohort of high school football players for two seasons of observation. Acceleration sensors were placed in the helmets, and all contact activity was monitored. Pre-season computer-based neuropsychological tests and functional magnetic resonance imaging (fMRI) tests were also obtained in order to assess cognitive and neurophysiological health. In-season follow-up scans were then obtained both from individuals who had sustained a clinically-diagnosed concussion and those who had not. These changes were then related through stepwise regression to history of blows recorded throughout the football season up to the date of the scan. In addition to those subjects who had sustained a concussion, a substantial portion of our cohort who did not sustain concussions showed significant neurophysiological changes. Stepwise regression indicated significant relationships between the number of blows sustained by a subject and the ensuing neurophysiological change. Our findings reinforce the hypothesis that the effects of repetitive blows to the head are cumulative and that repeated exposure to subconcussive blows is connected to pathologically altered neurophysiology. Copyright © 2012 Elsevier Ltd. All rights reserved.

Criteria on global boundedness versus finite time blow-up to a two-species chemotaxis system with two chemicals

NASA Astrophysics Data System (ADS)

Yu, Hao; Wang, Wei; Zheng, Sining

2018-02-01

This paper considers the two-species chemotaxis system with two chemicals in a smooth bounded domain Ω\\subset{R}2 , subject to the non-flux boundary condition, and χ, ξ, α, β, γ, δ>0 . We obtain a blow-up criterion that if m_1m_2-2π(\\frac{m_1}χβ+\\frac{m_2}ξδ)>0 , then there exist finite time blow-up solutions to the system with m_1:=\\int_Ω u_0(x)dx and m_2:=\\int_Ω w_0(x)dx . When χ=ξ= β=δ=1 , the blow-up criterion becomes m_1m_2-2π(m_1+m_2)>0 , and the global boundedness of solutions is furthermore established with α=γ=1 under the condition that \\max\\{m_1, m_2\\}<4π . This improves the current results for finite time blow-up with \\min\\{m_1, m_2\\}>4π and global boundedness with \\max\\{m_1, m_2\\}<\\frac{4}{C_GN} respectively in Tao and Winkler (2015 Discrete Contin. Dyn. Syst. Ser. B 20 3165-83) Supported by the National Natural Science Foundation of China (11171048), the Science Foundation of Liaoning Education Department grant (LYB201601) and the Fundamental Research Funds for the Central Universities (DUT16LK24).

Clinical profile of commotio cordis: an under appreciated cause of sudden death in the young during sports and other activities.

PubMed

Maron, B J; Link, M S; Wang, P J; Estes, N A

1999-01-01

Not particularly well recognized are athletic field catastrophes in which virtually instantaneous cardiac arrest is produced by nonpenetrating chest blows in the absence of heart disease or identifiable morphologic injury to the chest wall or heart (commotio cordis). To better characterize the clinical profile of this syndrome, we have assembled 70 cases, including 34 occurring during organized competitive athletics and 36 others that occurred during informal recreational sports at home, school or the playground, or during nonsporting activities. Ages were 2 to 38 (mean age: 12) with 70% < 16 years old. Most common sports involved were youth baseball (n = 40), softball (n = 7), and ice hockey (n = 7). Seven (10%) of the 70 commotio cordis victims, including six with documented ventricular fibrillation, have survived the consequences of their chest blow. Eleven of the events (16%) occurred despite the presence of chest padding believed to be potentially protective. Four victims experienced modest chest blows while in circumstances completely unrelated to sports activities; three of the four individuals who delivered these blows were ultimately convicted of criminal acts within the justice system. An experimental model of low-energy chest wall impact demonstrates that commotio cordis events are due largely to the exquisite timing of blows during a narrow window within the repolarization phase of the cardiac cycle, 15 to 30 msec prior to the peak of the T wave.

Bromine release from blowing snow and its impact on tropospheric chemistry

NASA Astrophysics Data System (ADS)

Griffiths, Paul; Yang, Xin; Abraham, N. Luke; Archibald, Alexander; Pyle, John

2016-04-01

In the last two decades, significant depletion of boundary layer ozone (ozone depletion events, ODEs) has been observed in both Arctic and Antarctic spring. ODEs are attributed to catalytic destruction by bromine radicals (Br plus BrO), especially during bromine explosion events (BEs), when high concentrations of BrO periodically occur. The source of bromine and the mechanism that sustains the high BrO levels are still the subject of study. Recent work by Pratt et al. (2013) posits Br2 production within saline snow and sea ice which leads to sudden ODEs. Previously, Yang et al. (2008) suggested snow could provide a source of (depleted) sea-salt aerosol if wicked from the surface of ice. They suggest that rapid depletion of bromide from the aerosol will constitute a source of photochemical Bry. Given the large sea ice extent in polar regions, this may constitute a significant source of sea salt and bromine in the polar lower atmosphere. While bromine release from blowing snow is perhaps less likely to trigger sudden ODEs, it may make a contribution to regional scale processes affecting ozone levels. Currently, the model parameterisations of Yang et al. assumes that rapid release of bromine occurs from fresh snow on sea ice during periods of strong wind. The parameterisation depends on an assumed sea-salt aerosol distribution generated via sublimation of the snow above the boundary layer, as well as taking into account the salinity of the snow. In this work, we draw on recent measurements by scientists from the British Antarctic Survey during a cruise aboard the Polarstern in the southern oceans. This has provided an extensive set of measurements of the chemical and physical characteristics of blowing snow over sea ice, and of the aerosol associated with it. Based on the observations, we have developed an improved parameterisation of the release of bromine from blowing snow. The paper presents results from the simulation performed using the United Kingdom Chemistry and Aerosols (UKCA) model, run as a component of the UK Met Office Unified Model, employing the updated parameterisation of Yang et al. We assess the performance of the parameterisation in simulating tropospheric BrO, a review of relevant parameters, as well as a quantitative assessment of the release of sea salt aerosol and its contribution to halogen chemistry in the polar and global atmosphere.

Observations on morphology of immature Lucilia porphyrina (Diptera: Calliphoridae), a fly species of forensic importance.

PubMed

Klong-Klaew, Tunwadee; Sukontason, Kom; Sribanditmongkol, Pongruk; Moophayak, Kittikhun; Sanit, Sangob; Sukontason, Kabkaew L

2012-11-01

Lucilia porphyrina (Walker) is a blow fly of forensic importance, and shares its geographical distribution with a related forensically important species, Lucilia cuprina (Wiedemann). The immature stages of both species are similar in general appearance; therefore, correct identification should be given special consideration. This study highlighted the main features of L. porphyrina larvae, as observed under light microscopy and scanning electron microscopy. Particular attention is given to the anterior and posterior spiracles, cephalopharyngeal skeleton, and characteristics of the dorsal spines between the prothorax and mesothorax. In the third instar specifically, morphological information on L. porphyrina showed several features that are shared by L. cuprina, and therefore need certain identification to distinguish between them. Such key features are (1) greater posterior spiracle, (2) apparent inner projection between the middle and lower slits of the posterior spiracle, and (3) strongly sclerotized peritreme. The number of papillae on the anterior spiracle may be a supplement, five to nine and three to six in L. porphyrina and L. cuprina, respectively. The key for identifying third instar of forensically important flies in Thailand has been updated to include L. porphyrina.

Individual and Situational Correlates of Whistle-Blowing.

ERIC Educational Resources Information Center

Miceli, Marcia P.; Near, Janet P.

1988-01-01

Analyzed archival survey data from observers of wrongdoing in 22 organizations. Found whistle-blowing more likely when observers held professional positions, had positive reactions to their work, had longer service, were recently recognized for good performance, were male, were members of larger work groups, and were employed by organizations…

Unsavory Problems at Tasty's: A Role-Play about Whistle-Blowing

ERIC Educational Resources Information Center

Comer, Debra R.; Vega, Gina

2006-01-01

This article presents a role-play exercise to make the topic of whistle-blowing personally salient to undergraduates. Students identify with the prospective whistle-blower, whose decision affects several stakeholders. The protagonist merely suspects her manager of stealing, until she hears concrete evidence of his thefts from her assistant…

76 FR 36571 - Bowdoin National Wildlife Refuge Complex, Malta, MT; Comprehensive Conservation Plan

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-22

... fishery due to high salinity levels or shallow water depth. Excluding Holm WPA, the remaining complex is... Thibadeau, and five alternatives for addressing the salinity and blowing salts issue on Bowdoin National... Alternative 2--Divestiture (proposed action). Alternatives for Salinity and Blowing Salts on Bowdoin National...

Nondestructive test determines overload destruction characteristics of current limiter fuses

NASA Technical Reports Server (NTRS)

Swartz, G. A.

1968-01-01

Nondestructive test predicts the time required for current limiters to blow /open the circuit/ when subjected to a given overload. The test method is based on an empirical relationship between the voltage rise across a current limiter for a fixed time interval and the time to blow.

[Diagnostic image (113). A neonate blowing bubbles. Esophageal atresia with tracheoesophageal fistula, Hirschsprung disease and suspected Down's syndrome].

PubMed

Postema, R R; Meradji, M; Langemeijer, R A Th M

2002-11-09

In a male neonate 'blowing bubbles', three diagnoses were seen on a combined thoracic and abdominal X-ray: esophageal atresia with tracheoesophageal fistula, Hirschsprung's disease, and suspected Down's syndrome (because of the presence of II pairs of ribs).

The Early Years: Blowing Bubbles

ERIC Educational Resources Information Center

Ashbrook, Peggy

2016-01-01

Blowing bubbles is not only a favorite summer activity for young children. Studying bubbles that are grouped together, or "foam," is fun for children and fascinating to many real-world scientists. Foam is widely used--from the bedroom (mattresses) to outer space (insulating panels on spacecraft). Bubble foam can provide children a…

Solution blow spun spinel ferrite and highly porous silica nanofibers

USDA-ARS?s Scientific Manuscript database

The novelty of this work is the production of nano- and submicrometric silica and spinel-ferrite fibers using the solution blow spinning (SBS) method. A pseudo-core-shell method for the production of large surface area silica fibers is also reported. Silica fibers present mean diameters and specific...

40 CFR 63.8698 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... facility used to transfer oxidized asphalt from a storage tank into a tank truck, rail car, or barge... facility includes one or more asphalt flux blowing stills, asphalt flux storage tanks storing asphalt flux intended for processing in the blowing stills, oxidized asphalt storage tanks, and oxidized asphalt loading...

Large wind ripples on Mars: A record of atmospheric evolution

NASA Astrophysics Data System (ADS)

Lapotre, M. G. A.; Ewing, R. C.; Lamb, M. P.; Fischer, W. W.; Grotzinger, J. P.; Rubin, D. M.; Lewis, K. W.; Ballard, M. J.; Day, M.; Gupta, S.; Banham, S. G.; Bridges, N. T.; Des Marais, D. J.; Fraeman, A. A.; Grant, J. A.; Herkenhoff, K. E.; Ming, D. W.; Mischna, M. A.; Rice, M. S.; Sumner, D. A.; Vasavada, A. R.; Yingst, R. A.

2016-07-01

Wind blowing over sand on Earth produces decimeter-wavelength ripples and hundred-meter- to kilometer-wavelength dunes: bedforms of two distinct size modes. Observations from the Mars Science Laboratory Curiosity rover and the Mars Reconnaissance Orbiter reveal that Mars hosts a third stable wind-driven bedform, with meter-scale wavelengths. These bedforms are spatially uniform in size and typically have asymmetric profiles with angle-of-repose lee slopes and sinuous crest lines, making them unlike terrestrial wind ripples. Rather, these structures resemble fluid-drag ripples, which on Earth include water-worked current ripples, but on Mars instead form by wind because of the higher kinematic viscosity of the low-density atmosphere. A reevaluation of the wind-deposited strata in the Burns formation (about 3.7 billion years old or younger) identifies potential wind-drag ripple stratification formed under a thin atmosphere.

Process computerization of No. 13 blast furnace at Gary works

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sherman, G.J.; Zmierski, M.L.; Hyle, F.W.

1993-10-01

No. 13 blast furnace underwent extensive modifications to the process control system during the second reline. This represents a major shift in control philosophy from hardwired relays and analog controllers to a totally integrated computer control system. The new system created the opportunity for comprehensive diagnostic analysis and increased flexibility for control strategy modifications. The goal of achieving maximum production with minimal delay was accomplished by an integrated test, and comprehensive operator and maintenance training. Normal production was reached within four days of blow-ink and design production capacity of 7800 NTHM/day was met in the third month of operation. Recordmore » furnace productivity of 8931 NTHM/day (8.56 NTHM/100 crwv) was achieved in less than five months of operation and again in April 1992 of 9062 NTHM/day (8.68 NTHM/100 cfwv).« less