Subscale solid motor nozzle tests, phase 4 and nozzle materials screening and thermal characterization, phase 5

NASA Technical Reports Server (NTRS)

Arnold, J.; Dodson, J.; Laub, B.

1979-01-01

Subscale solid motor nozzles containing a baseline material or low cost materials to be considered as potential replacements for the baseline material are designed and tested. Data are presented from tests of four identically designed 2.5 inch throat diameter nozzles and one 7 inch throat diameter nozzle. The screening of new candidate low cost materials, as well as their thermophysical and thermochemical characterization is also discussed.

Effect of ITE and nozzle exit cone erosion on specific impulse of solid rocket motors

NASA Astrophysics Data System (ADS)

Smith-Kent, Randall; Ridder, Jeffrey P.; Loh, Hai-Tien; Abel, Ralph

1993-06-01

Specific impulse loss due to the use of a slowly eroding integral throat entrance, or a throat insert, with a faster eroding nozzle exit cone is studied. It is suggested that an oblique shock wave produced by step-off erosion results in loss of specific impulse. This is studied by use of a shock capturing CFD method. The shock loss predictions for first-stage Peacekeeper and Castor 25 motors are found to match the trends of the test data. This work suggests that a loss mechanism, previously unaccounted, should be considered in the specific impulse prediction procedure for nozzles with step-off exit cone erosion.

21 CFR 874.4800 - Bone particle collector.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bone particle collector. 874.4800 Section 874.4800...) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4800 Bone particle collector. (a) Identification. A bone particle collector is a filtering device intended to be inserted into a suction tube...

21 CFR 874.4800 - Bone particle collector.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Bone particle collector. 874.4800 Section 874.4800...) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4800 Bone particle collector. (a) Identification. A bone particle collector is a filtering device intended to be inserted into a suction tube...

21 CFR 874.4800 - Bone particle collector.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Bone particle collector. 874.4800 Section 874.4800...) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4800 Bone particle collector. (a) Identification. A bone particle collector is a filtering device intended to be inserted into a suction tube...

21 CFR 874.4800 - Bone particle collector.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Bone particle collector. 874.4800 Section 874.4800...) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4800 Bone particle collector. (a) Identification. A bone particle collector is a filtering device intended to be inserted into a suction tube...

21 CFR 874.4800 - Bone particle collector.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Bone particle collector. 874.4800 Section 874.4800...) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4800 Bone particle collector. (a) Identification. A bone particle collector is a filtering device intended to be inserted into a suction tube...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferrario, Lorenzo, E-mail: lorenzo.ferrario@polimi.it; Little, Justin M., E-mail: jml@princeton.edu; Choueiri, Edgar Y., E-mail: choueiri@princeton.edu

The plasma flow in a finite-electron-temperature magnetic nozzle, under the influence of an applied azimuthal current at the throat, is modeled analytically to assess its propulsive performance. A correction to the nozzle throat boundary conditions is derived by modifying the radial equilibrium of a magnetized infinite two-population cylindrical plasma column with the insertion of an external azimuthal body force for the electrons. Inclusion of finite-temperature effects, which leads to a modification of the radial density profile, is necessary for calculating the propulsive performance, which is represented by nozzle divergence efficiency and thrust coefficient. The solutions show that the application ofmore » the azimuthal current enhances all the calculated performance parameters through the narrowing of the radial density profile at the throat, and that investing power in this beam focusing effect is more effective than using the same power to pre-heat the electrons. The results open the possibility for the design of a focusing stage between the plasma source and the nozzle that can significantly enhance the propulsive performance of electron-driven magnetic nozzles.« less

Prophylactic dexamethasone decreases the incidence of sore throat and hoarseness after tracheal extubation with a double-lumen endobronchial tube.

PubMed

Park, Sang-Hyun; Han, Sung-Hee; Do, Sang-Hwan; Kim, Jung-Won; Rhee, Ka-young; Kim, Jin-Hee

2008-12-01

Postoperative sore throat and hoarseness are common complications after tracheal intubation, particularly after using a double-lumen endobronchial tube (DLT). We conducted a prospective, randomized, double-blind, placebo-controlled study to evaluate the efficacy of dexamethasone for reducing the incidence and severity of postoperative sore throat and hoarseness. One hundred sixty-six patients (aged 18-75 yr) scheduled for thoracic surgery with a DLT were enrolled. Before induction of general anesthesia, 0.1 mg/kg dexamethasone (Group D1), 0.2 mg/kg dexamethasone (Group D2), or a placebo (Group P) were infused i.v. in a double-blind and prospectively randomized manner. Glottic exposure as defined by Cormack and Lehane score, resistance to DLT insertion, number of intubation attempts, time to achieve intubation, and the duration of tracheal intubation were recorded. At 1 h and 24 h after tracheal extubation, the patients were evaluated for sore throat and hoarseness using a visual analog scale (VAS; where 0 = no pain and 100 = worst pain imaginable). One hour after tracheal extubation, the incidence of postoperative sore throat and hoarseness, along with the severity of sore throat were lower in Group D1 (31%, P = 0.021; 11%, P = 0.003; and VAS 12.4, P < 0.001, respectively) and D2 (11%, P = 0.001; 4%, P = 0.001; and VAS 6.6, P < 0.001, respectively) compared with Group P (53%, 36% and VAS 30.9, respectively). Twenty-four hours after tracheal extubation, the incidence of postoperative sore throat, hoarseness, and the severity of sore throat were significantly lower in Group D2 (27%, P = 0.002; 15%, P = 0.001; and VAS 29.9, P < 0.002, respectively) compared with Group D1 (47%, 31%, and VAS = 43.9, respectively) and Group P (57%, 45%, and VAS = 51.3, respectively). There was no complication associated with the dexamethasone administration. The prophylactic use of 0.2 mg/kg of dexamethasone significantly decreases the incidence and severity of sore throat and hoarseness 1 h and 24 h after tracheal extubation of a DLT.

An Investigation of Convergent-Divergent Diffusers at Mach Number 1.85

NASA Technical Reports Server (NTRS)

Wyatt, Demarquis D; Hunczak, Henry R

1947-01-01

An investigation has been conducted in the Cleveland 18- by 18-inch supersonic tunnel at a Mach number of 1.85 and angles of attack from 0 deg to 5 deg to determine optimum design configurations for a convergent-divergent type of supersonic diffuser with a subsonic diffuser of 5 deg included divergence angle. Total pressure recoveries in excess of theoretical recovery across a normal shock at a free-stream Mach number of 1.85 wore obtained with several configurations. The highest recovery for configurations without a cylindrical throat section was obtained with an inlet having an included convergence angle of 20 deg. Insertion of a 2-inch throat section between a 10 deg included angle inlet and the subsonic diffuser stabilized the shock inside the diffuser and resulted in recoveries as high as 0.838 free-stream total pressure at an angle of attack of 0 deg, corresponding to recovery of 92.4 percent of the kinetic energy of the free air stream. Use of the throat section also lessened the reduction in recovery of all configurations due to angle of attack.

Anode Sheath Contributions in Plasma Thrusters

DTIC Science & Technology

1994-03-01

and considerable throat erosion, is shown to be related to the electron temperature’s (T) rise above the gas temperature (To). An elementary one...surface damage and considerable throat erosion, is shown to be related to the electron temperature’s (T.) rise above the gas temperature (T.). An...Exhaust velocity is also limited hy material heating limitations of the combustion chamber and nozzle throat , and "frozen flow Losses" (unrecoverable energy

Extrusion of electrode material by liquid injection into extruder barrel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, David Gerard; Giovannoni, Richard Thomas; MacFadden, Kenneth Orville

An electrode sheet product is formed using an extruder having a feed throat and a downstream section by separately mixing an active electrode material and a solid polymer electrolyte composition that contains lithium salt. The active electrode material is fed into the feed throat of the extruder, while a portion of at least one fluid component of the solid polymer electrolyte composition is introduced to the downstream section. The active electrode material and the solid polymer electrolyte composition are compounded in a downstream end of the extruder. The extruded sheets, adhered to current collectors, can be formed into battery cells.

[Discovery of Chlamydia trachomatis in the throat during diagnosis of secondary syphilis in an HIV+ patient].

PubMed

Deniaud, François; Scieux, Catherine; Spindler, Edith; Janier, Michel

2003-09-20

Chlamydia trachomatis (CT) pharyngitis has rarely been described in the literature. Studies in the last decade have shown a prevalence of less than 5%, with more women than men infected in the pharynx. Among homosexual men, only one study, conducted more than 5 years ago, detected the presence of CT in the throat (in one patient out of 13 tested). A 33 year-old homosexual man consulted for cutaneous lesions on the palms and the chest. Infected by HIV, he was taking antiretroviral therapy but no antibiotic prophylaxis. He admitted practising unprotected (insertive and receptive) fellatio with unknown partners. The lesions were those of secondary syphilis but the location of the chancre remained unknown. An enlarged screening for sexually transmitted infections detected the presence, through molecular amplification, of CT in the throat without further localisation (urethra, anus). After intramuscular injection of Extencillin and an 8-day-regimen of cycline, CT was no longer detected in the throat. The course of HIV infection did not appear modified by this infectious episode. According to a review of the literature, the 4 most recent studies have not revealed CT in the throat of homosexuals although the bacteria was detected in the urethra of 3 to 4% of them. Chlamydia trachomatis is more frequently detected in the genital tract rather than the pharynx of women also screened in various localisations. These results must be tempered by the participant recruitment methods, diagnostic methods used, sample size and history of recent antibiotherapy. The pharyngeal mucosa might be less receptive to CT than the urethral mucosa. Association of CT pharyngitis with syphilis or its occurrence during HIV infection are not documented. The molecular amplification technique detects CT in the throat with sensitivity and specificity. A one-week regimen of cycline can cure this pharyngitis. Cost-effectiveness of screening for pharyngeal CT has not yet been assessed in persons 'at risk'.

Feasibility evaluation of the monolithic braided ablative nozzle

NASA Astrophysics Data System (ADS)

Director, Mark N.; McPherson, Douglass J., Sr.

1992-02-01

The feasibility of the monolithic braided ablative nozzle was evaluated as part of an independent research and development (IR&D) program complementary to the National Aeronautics and Space Administration/Marshall Space Flight Center (NASA/MSFC) Low-Cost, High-Reliability Case, Insulation and Nozzle for Large Solid Rocket Motors (LOCCIN) Program. The monolithic braided ablative nozzle is a new concept that utilizes a continuous, ablative, monolithic flame surface that extends from the nozzle entrance, through the throat, to the exit plane. The flame surface is fabricated using a Through-the-Thickness braided carbon-fiber preform, which is impregnated with a phenolic or phenolic-like resin. During operation, the braided-carbon fiber/resin material ablates, leaving the structural backside at temperatures which are sufficiently low to preclude the need for any additional insulative materials. The monolithic braided nozzle derives its potential for low life cycle cost through the use of automated processing, one-component fabrication, low material scrap, low process scrap, inexpensive raw materials, and simplified case attachment. It also has the potential for high reliability because its construction prevents delamination, has no nozzle bondlines or leak paths along the flame surface, is amenable to simplified analysis, and is readily inspectable. In addition, the braided construction has inherent toughness and is damage-tolerant. Two static-firing tests were conducted using subscale, 1.8 - 2.0-inch throat diameter, hardware. Tests were approximately 15 seconds in duration, using a conventional 18 percent aluminum/ammonium perchlorate propellant. The first of these tests evaluated the braided ablative as an integral backside insulator and exit cone; the second test evaluated the monolithic braided ablative as an integral entrance/throat/exit cone nozzle. Both tests met their objectives. Radial ablation rates at the throat were as predicted, approximately 0.017 in/sec; these rates are comparable to those for tapewrapped carbon phenolic materials. The maximum temperature rise on the outside surface occurred one inch from the nozzle exit plane and was less than 50 F at the end of the test. Further development for this concept is scheduled as part of phase 2 on the NASA/MSFC LOCCIN Program. During this effort, the nozzle materials, architecture, and processing will be optimized and tested in nozzles with 3- and 10-inch diameter throats. Further, a design and manufacturing plan for a full-scale, 20-inch-diameter throat, nozzle will be developed.

Extrusion of electrode material by liquid injection into extruder barrel

DOEpatents

Keller, D.G.; Giovannoni, R.T.; MacFadden, K.O.

1998-03-10

An electrode sheet product is formed using an extruder having a feed throat and a downstream section by separately mixing an active electrode material and a solid polymer electrolyte composition that contains lithium salt. The active electrode material is fed into the feed throat of the extruder, while a portion of at least one fluid component of the solid polymer electrolyte composition is introduced to the downstream section. The active electrode material and the solid polymer electrolyte composition are compounded in a downstream end of the extruder. The extruded sheets, adhered to current collectors, can be formed into battery cells. 1 fig.

Extrusion of electrode material by liquid injection into extruder barrel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, D.G.; Giovannoni, R.T.; MacFadden, K.O.

An electrode sheet product is formed using an extruder having a feed throat and a downstream section by separately mixing an active electrode material and a solid polymer electrolyte composition that contains lithium salt. The active electrode material is fed into the feed throat of the extruder, while a portion of at least one fluid component of the solid polymer electrolyte composition is introduced to the downstream section. The active electrode material and the solid polymer electrolyte composition are compounded in a downstream end of the extruder. The extruded sheets, adhered to current collectors, can be formed into battery cells.more » 1 fig.« less

Crack cause analysis of a graphite nozzle throat insert

NASA Astrophysics Data System (ADS)

Sun, Lin; Bao, Futing; Zhao, Yu; Hou, Lian; Hui, Weihua; Zhang, Ning; Shi, Wei

2017-08-01

With an objective to determine the failure cause of a throughout crack at an angle of 45° and a breach during a firing test, a simplified analysis procedure with consideration of the structure gap was established to simulate the thermo-structural response of a nozzle. By neglecting erosion and pyrolysis of the insulating materials and establishing temperature-dependent or anisotropic material models, ANSYS Parameter Design Language codes were written to perform the fully coupled thermal-structural simulation. A Quasi-1D flow was calculated for supplying boundary conditions. Study on mesh independence and time step independence was also conducted to evaluate simulated results. It was found that shortly after ignition, compressive stress in the x direction and tensile stress in the y direction contributed to anomalies. And through contact status analysis, inappropriate gap design was regarded as the origin of the too large stress, which was the primary cause of these anomalies during firing test. Simulation results were in good agreement with firing test results. In addition, the simplified analysis procedure was proven effective. Gap size should be seriously dealt with in the future design.

Virtual impactor

DOEpatents

Yeh, Hsu-Chi; Chen, Bean T.; Cheng, Yung-Sung; Newton, George J.

1988-08-30

A virtual impactor having improved efficiency and low wall losses in which a core of clean air is inserted into the aerosol flow while aerosol flow is maintained adjacent inner wall surfaces of the focusing portion of the impactor. The flow rate of the core and the length of the throat of the impactor's collection probe, as well as the dimensional relationships of other components of the impactor adjacent the separation region of the impactor, are selected to optimize separation efficiency.

Estimation of the Human Extrathoracic Deposition Fraction of Inhaled Particles Using a Polyurethane Foam Collection Substrate in an IOM Sampler.

PubMed

Sleeth, Darrah K; Balthaser, Susan A; Collingwood, Scott; Larson, Rodney R

2016-03-07

Extrathoracic deposition of inhaled particles (i.e., in the head and throat) is an important exposure route for many hazardous materials. Current best practices for exposure assessment of aerosols in the workplace involve particle size selective sampling methods based on particle penetration into the human respiratory tract (i.e., inhalable or respirable sampling). However, the International Organization for Standardization (ISO) has recently adopted particle deposition sampling conventions (ISO 13138), including conventions for extrathoracic (ET) deposition into the anterior nasal passage (ET₁) and the posterior nasal and oral passages (ET₂). For this study, polyurethane foam was used as a collection substrate inside an inhalable aerosol sampler to provide an estimate of extrathoracic particle deposition. Aerosols of fused aluminum oxide (five sizes, 4.9 µm-44.3 µm) were used as a test dust in a low speed (0.2 m/s) wind tunnel. Samplers were placed on a rotating mannequin inside the wind tunnel to simulate orientation-averaged personal sampling. Collection efficiency data for the foam insert matched well to the extrathoracic deposition convention for the particle sizes tested. The concept of using a foam insert to match a particle deposition sampling convention was explored in this study and shows promise for future use as a sampling device.

Estimation of the Human Extrathoracic Deposition Fraction of Inhaled Particles Using a Polyurethane Foam Collection Substrate in an IOM Sampler

PubMed Central

Sleeth, Darrah K.; Balthaser, Susan A.; Collingwood, Scott; Larson, Rodney R.

2016-01-01

Extrathoracic deposition of inhaled particles (i.e., in the head and throat) is an important exposure route for many hazardous materials. Current best practices for exposure assessment of aerosols in the workplace involve particle size selective sampling methods based on particle penetration into the human respiratory tract (i.e., inhalable or respirable sampling). However, the International Organization for Standardization (ISO) has recently adopted particle deposition sampling conventions (ISO 13138), including conventions for extrathoracic (ET) deposition into the anterior nasal passage (ET1) and the posterior nasal and oral passages (ET2). For this study, polyurethane foam was used as a collection substrate inside an inhalable aerosol sampler to provide an estimate of extrathoracic particle deposition. Aerosols of fused aluminum oxide (five sizes, 4.9 µm–44.3 µm) were used as a test dust in a low speed (0.2 m/s) wind tunnel. Samplers were placed on a rotating mannequin inside the wind tunnel to simulate orientation-averaged personal sampling. Collection efficiency data for the foam insert matched well to the extrathoracic deposition convention for the particle sizes tested. The concept of using a foam insert to match a particle deposition sampling convention was explored in this study and shows promise for future use as a sampling device. PMID:26959046

Comparison of Effectiveness of Betamethasone gel Applied to the Tracheal Tube and IV Dexamethasone on Postoperative Sore Throat: A Randomized Controlled Trial

PubMed Central

Tabari, Masoomeh; Soltani, Ghasem; Zirak, Nahid; Alipour, Mohammad; Khazaeni, Kamran

2013-01-01

Introduction: Postoperative sore throat is a common complaint in patients with endotracheal intubation and has potentially dangerous complications. This randomized controlled trial study investigated the incidence of postoperative sore throat after general anesthesia when betamethasone gel is applied to a tracheal tube compared with when IV dexamethasone is prescribed. Materials and Methods: Two hundred and twenty five American Society of Anesthesiologist (ASA)-class I and II patients undergoing elective abdominal surgery with tracheal intubation were randomly divided into three groups: betamethasone gel, intravenous (IV) dexamethasone, and control groups. In the post-anesthesia care unit, a blinded anesthesiologist interviewed all patients regarding postoperative sore throat at 1,6, and 24 hours after surgery. Results: The incidence of sore throat was significantly lower in the betamethasone gel group compared with the IV dexamethasone and control groups, 1, 6, and 24 hours after surgery. In the first day after surgery 10.7% of the betamethasone group had sore throat whereas 26.7% of the IV dexamethasone group and 30.7% of the control group had sore throat. Bucking before extubation was observed in 14(18.4%), 8(10.4%), and 9(12.2%) patients, in the IV dexamethasone, betamethasone gel, and control group, respectively. Conclusion: We concluded that wide spread application of betamethasone gel over tracheal tubes effectively mitigates postoperative sore throat, compared with IV dexamethasone application. PMID:24303443

Indirect and direct methods for measuring a dynamic throat diameter in a solid rocket motor

NASA Astrophysics Data System (ADS)

Colbaugh, Lauren

In a solid rocket motor, nozzle throat erosion is dictated by propellant composition, throat material properties, and operating conditions. Throat erosion has a significant effect on motor performance, so it must be accurately characterized to produce a good motor design. In order to correlate throat erosion rate to other parameters, it is first necessary to know what the throat diameter is throughout a motor burn. Thus, an indirect method and a direct method for determining throat diameter in a solid rocket motor are investigated in this thesis. The indirect method looks at the use of pressure and thrust data to solve for throat diameter as a function of time. The indirect method's proof of concept was shown by the good agreement between the ballistics model and the test data from a static motor firing. The ballistics model was within 10% of all measured and calculated performance parameters (e.g. average pressure, specific impulse, maximum thrust, etc.) for tests with throat erosion and within 6% of all measured and calculated performance parameters for tests without throat erosion. The direct method involves the use of x-rays to directly observe a simulated nozzle throat erode in a dynamic environment; this is achieved with a dynamic calibration standard. An image processing algorithm is developed for extracting the diameter dimensions from the x-ray intensity digital images. Static and dynamic tests were conducted. The measured diameter was compared to the known diameter in the calibration standard. All dynamic test results were within +6% / -7% of the actual diameter. Part of the edge detection method consists of dividing the entire x-ray image by an average pixel value, calculated from a set of pixels in the x-ray image. It was found that the accuracy of the edge detection method depends upon the selection of the average pixel value area and subsequently the average pixel value. An average pixel value sensitivity analysis is presented. Both the indirect method and the direct method prove to be viable approaches to determining throat diameter during solid rocket motor operation.

Virtual impactor

DOEpatents

Yeh, H.C.; Chen, B.T.; Cheng, Y.S.; Newton, G.J.

1988-08-30

A virtual impactor is described having improved efficiency and low wall losses in which a core of clean air is inserted into the aerosol flow while aerosol flow is maintained adjacent to the inner wall surfaces of the focusing portion of the impactor. The flow rate of the core and the length of the throat of the impactor's collection probe, as well as the dimensional relationships of other components of the impactor adjacent the separation region of the impactor, are selected to optimize separation efficiency. 4 figs.

Comparative analysis of emm type pattern of Group A Streptococcus throat and skin isolates from India and their association with closely related SIC, a streptococcal virulence factor

PubMed Central

Sagar, Vivek; Kumar, Rajesh; Ganguly, Nirmal K; Chakraborti, Anuradha

2008-01-01

Background Group A streptococcus (GAS) causes a wide variety of life threatening diseases in humans and the incidence of such infections is high in developing countries like India. Although distribution of emm types of GAS in India has been described, there is a lack of data describing either the comparative distribution of emm types in throat versus skin isolates, or the distribution of certain virulence factors amongst these isolates. Therefore in the present study we have monitored the emm type pattern of Group A streptococcus throat and skin isolates from India. Additionally, the association of these isolates with closely related sic (crs), a multifunctional compliment binding virulence factor, was also explored. Results Of the 94 (46 throat and 48 skin) isolates analyzed, 37 emm types were identified. The most frequently observed emm types were emm49 (8.5%) and emm112 (7.5%) followed by 6.5% each of emm1-2, emm75, emm77, and emm81. Out of 37 emm types, 27 have been previously reported and rest were isolated for the first time in the Indian Community. The predominant emm types of throat (emm49 and emm75) samples were different from those of skin (emm44, emm81 and emm112) samples. After screening all the 94 isolates, the crs gene was found in six emm1-2 (crs1-2) isolates, which was confirmed by DNA sequencing and expression analysis. Despite the polymorphic nature of crs, no intravariation was observed within crs1-2. However, insertions and deletions of highly variable sizes were noticed in comparison to CRS isolated from other emm types (emm1.0, emm57). CRS1-2 showed maximum homology with CRS57, but the genomic location of crs1-2 was found to be the same as that of sic1.0. Further, among crs positive isolates, speA was only present in skin samples thus suggesting possible role of speA in tissue tropism. Conclusion Despite the diversity in emm type pattern of throat and skin isolates, no significant association between emm type and source of isolation was observed. The finding that the crs gene is highly conserved even in two different variants of emm1-2 GAS (speA +ve and -ve) suggests a single allele of crs may be prevalent in the highly diverse throat and skin isolates of GAS in India. PMID:18796133

Comparative analysis of emm type pattern of Group A Streptococcus throat and skin isolates from India and their association with closely related SIC, a streptococcal virulence factor.

PubMed

Sagar, Vivek; Kumar, Rajesh; Ganguly, Nirmal K; Chakraborti, Anuradha

2008-09-16

Group A streptococcus (GAS) causes a wide variety of life threatening diseases in humans and the incidence of such infections is high in developing countries like India. Although distribution of emm types of GAS in India has been described, there is a lack of data describing either the comparative distribution of emm types in throat versus skin isolates, or the distribution of certain virulence factors amongst these isolates. Therefore in the present study we have monitored the emm type pattern of Group A streptococcus throat and skin isolates from India. Additionally, the association of these isolates with closely related sic (crs), a multifunctional compliment binding virulence factor, was also explored. Of the 94 (46 throat and 48 skin) isolates analyzed, 37 emm types were identified. The most frequently observed emm types were emm49 (8.5%) and emm112 (7.5%) followed by 6.5% each of emm1-2, emm75, emm77, and emm81. Out of 37 emm types, 27 have been previously reported and rest were isolated for the first time in the Indian Community. The predominant emm types of throat (emm49 and emm75) samples were different from those of skin (emm44, emm81 and emm112) samples. After screening all the 94 isolates, the crs gene was found in six emm1-2 (crs1-2) isolates, which was confirmed by DNA sequencing and expression analysis. Despite the polymorphic nature of crs, no intravariation was observed within crs1-2. However, insertions and deletions of highly variable sizes were noticed in comparison to CRS isolated from other emm types (emm1.0, emm57). CRS1-2 showed maximum homology with CRS57, but the genomic location of crs1-2 was found to be the same as that of sic1.0. Further, among crs positive isolates, speA was only present in skin samples thus suggesting possible role of speA in tissue tropism. Despite the diversity in emm type pattern of throat and skin isolates, no significant association between emm type and source of isolation was observed. The finding that the crs gene is highly conserved even in two different variants of emm1-2 GAS (speA +ve and -ve) suggests a single allele of crs may be prevalent in the highly diverse throat and skin isolates of GAS in India.

An example of successful international cooperation in rocket motor technology

NASA Astrophysics Data System (ADS)

Ellis, Russell A.; Berdoyes, Michel

2002-07-01

The history of over 25 years of cooperation between Pratt & Whitney, San Jose, CA, USA and Snecma Moteurs, Le Haillan, France in solid rocket motor and, in one case, liquid rocket engine technology is presented. Cooperative efforts resulted in achievements that likely would not have been realized individually. The combination of resources and technologies resulted in synergistic benefits and advancement of the state of the art in rocket motors and components. Discussions begun between the two companies in the early 1970's led to the first cooperative project, demonstration of an advanced apogee motor nozzle, during the mid 1970's. Shortly thereafter advanced carboncarbon (CC) throat materials from Snecma were comparatively tested with other materials in a P&W program funded by the USAF. Use of Snecma throat materials in CSD Tomahawk boosters followed. Advanced space motors were jointly demonstrated in company-funded joint programs in the late 1970's and early 1980's: an advanced space motor with an extendible exit cone and an all-composite advanced space motor that included a composite chamber polar adapter. Eight integral-throat entrances (ITEs) of 4D and 6D construction were tested by P&W for Snecma in 1982. Other joint programs in the 1980's included test firing of a "membrane" CC exit cone, and integral throat and exit cone (ITEC) nozzle incorporating NOVOLTEX® SEPCARB® material. A variation of this same material was demonstrated as a chamber aft polar boss in motor firings that included demonstration of composite material hot gas valve thrust vector control (TVC). In the 1990's a supersonic splitline flexseal nozzle was successfully demonstrated by the two companies as part of a US Integrated High Payoff Rocket Propulsion Technology (IHPRPT) program effort. Also in the mid-1990s the NOVOLTEX® SEPCARB® material, so successful in solid rocket motor application, was successfully applied to a liquid engine nozzle extension. The first cooperative effort for the new millennium, a scale-up of the supersonic splitline flexseal nozzle, was begun in 2001. Key details of the above numerous cooperative successes are presented.

Study into the correlation of dominant pore throat size and SIP relaxation frequency

NASA Astrophysics Data System (ADS)

Kruschwitz, Sabine; Prinz, Carsten; Zimathies, Annett

2016-12-01

There is currently a debate within the SIP community about the characteristic textural length scale controlling relaxation time of consolidated porous media. One idea is that the relaxation time is dominated by the pore throat size distribution or more specifically the modal pore throat size as determined in mercury intrusion capillary pressure tests. Recently new studies on inverting pore size distributions from SIP data were published implying that the relaxation mechanisms and controlling length scale are well understood. In contrast new analytical model studies based on the Marshall-Madden membrane polarization theory suggested that two relaxation processes might compete: the one along the short narrow pore (the throat) with one across the wider pore in case the narrow pores become relatively long. This paper presents a first systematically focused study into the relationship of pore throat sizes and SIP relaxation times. The generality of predicted trends is investigated across a wide range of materials differing considerably in chemical composition, specific surface and pore space characteristics. Three different groups of relaxation behaviors can be clearly distinguished. The different behaviors are related to clay content and type, carbonate content, size of the grains and the wide pores in the samples.

Thermal Analysis in Support of the Booster Separation Motor Crack Investigation

NASA Technical Reports Server (NTRS)

Davis, Darrell; Prickett, Terry; Turner, Larry D. (Technical Monitor)

2001-01-01

During a post-test inspection of a Booster Separation Motor (BSM) from a Lot Acceptance Test (LAT), a crack was noticed in the graphite throat. Since this was an out-of-family occurrence, an investigation team was formed to determine the cause of the crack. This paper will describe thermal analysis techniques used in support of this investigation. Models were generated to predict gradients in nominal motor conditions, as well as potentially anomalous conditions. Analysis was also performed on throats that were tested in the Laser Hardened Material Evaluation Laboratory (LHMEL). Some of these throats were pre-cracked, while others represented configurations designed to amplify effects of thermal stresses. Results from these analyses will be presented in this paper.

Thermal Analysis in Support of the Booster Separation Motor Crack Investigation

NASA Technical Reports Server (NTRS)

Davis, Darrell; Prickett, Terry

2002-01-01

During a post-test inspection of a Booster Separation Motor (BSM) from a Lot Acceptance Test (LAT), a crack was noticed in the graphite throat. Since this was an out-of-family occurrence, an investigation team was formed to determine the cause of the crack. This paper will describe thermal analysis techniques used in support of this investigation. Models were generated to predict gradients in nominal motor conditions, as well as potentially anomalous conditions. Analysis was also performed on throats that were tested in the Laser Hardened Material Evaluation Laboratory (LHMEL). Some of these throats were pre-cracked, while others represented configurations designed to amplify effects of thermal stresses. Results from these analyses will be presented in this paper.

RSRM Nozzle Anomalous Throat Erosion Investigation Overview

NASA Technical Reports Server (NTRS)

Clinton, R. G., Jr.; Wendel, Gary M.

1998-01-01

In September, 1996, anomalous pocketing erosion was observed in the aft end of the throat ring of the nozzle of one of the reusable solid rocket motors (RSRM 56B) used on NASA's space transportation system (STS) mission 79. The RSRM throat ring is constructed of bias tape-wrapped carbon cloth/ phenolic (CCP) ablative material. A comprehensive investigation revealed necessary and sufficient conditions for occurrence of the pocketing event and provided rationale that the solid rocket motors for the subsequent mission, STS-80, were safe to fly. The nozzles of both of these motors also exhibited anomalous erosion similar to, but less extensive than that observed on STS-79. Subsequent to this flight, the investigation to identify both the specific causes and the corrective actions for elimination of the necessary and sufficient conditions for the pocketing erosion was intensified. A detailed fault tree approach was utilized to examine potential material and process contributors to the anomalous performance. The investigation involved extensive constituent and component material property testing, pedigree assessments, supplier audits, process audits, full scale processing test article fabrication and evaluation, thermal and thermostructural analyses, nondestructive evaluation, and material performance tests conducted using hot fire simulation in laboratory test beds and subscale and full scale solid rocket motor static test firings. This presentation will provide an over-view of the observed anomalous nozzle erosion and the comprehensive, fault-tree based investigation conducted to resolve this issue.

Incidence of nest material kleptoparasitism invlovling cerulean warblers

Treesearch

Kelly C. Jones; Kirk L. Roth; Kamal Islam; Paul B. Hamel; Carl G. III Smith

2007-01-01

document 21 observations of interspecific stealing of nesting material involving Cerulean Warblers (Dendroica cerulea), Red-eyed Vireos (Vireo olivaceus/i>), Blue-gray Gnatcatchers (Polioptila caerulea/i>), Northern Parulas (Parula americana/i>), Black-throated Green Warblers (D. virens), American Redstarts (

'Food Sticking in My Throat': Videofluoroscopic Evaluation of a Common Symptom.

PubMed

Madhavan, Aarthi; Carnaby, Giselle D; Crary, Michael A

2015-06-01

Prevalence of the symptom of food 'sticking' during swallowing has been reported to range from 5 to 50%, depending on the assessment setting. However, limited objective evidence has emerged to clarify factors that contribute to this symptom. Three hundred and fifteen patient records from an outpatient dysphagia clinic were reviewed to identify patients with symptoms of 'food sticking in the throat.' Corresponding videofluoroscopic swallowing studies for patients with this complaint were reviewed for the following variables: accuracy of symptom localization, identification and characteristics (anatomic, physiologic) of an explanatory cause for the symptom, and the specific swallowed material that identified the explanatory cause. One hundred and forty one patients (45%) were identified with a complaint of food 'sticking' in their throat during swallowing. Prevalence of explanatory findings on fluoroscopy was 76% (107/141). Eighty five percent (91/107) of explanatory causes were physiologic in nature, while 15% (16/107) were anatomic. The majority of explanatory causes were identified in the esophagus (71%). Symptom localization was more accurate when the explanatory cause was anatomic versus physiologic (75 vs. 18%). A non-masticated marshmallow presented with the highest diagnostic yield in identification of explanatory causes (71%). Patients complaining of 'food sticking in the throat' are likely to present with esophageal irregularities. Thus, imaging studies of swallowing function should include the esophagus. A range of materials, including a non-masticated marshmallow, is helpful in determining the location and characteristics of swallowing deficits contributing to this symptom.

Pegasus - Winged workhorse

NASA Astrophysics Data System (ADS)

Furniss, Tim

1988-08-01

DARPA has initiated the development of a three-stage, solid-propellant air-launched booster for the lofting of small military satellites, or 'lightsats'. This vehicle, designated 'Pegasus', will because of its substantial endoatmospheric mission segment serve as a testbed for the validation of the CFD codes used by NASA as analytical tools in the design of the National Aerospace Plane. The three rocket stages are novel designs, incorporating such features as three-dimensionally woven carbon-carbon integral throat inserts and carbon-phenolic nozzles. The aircraft that will take Pegasus to launch altitude will be the B-52 previously used to launch the X-15.

The effect of esophagogastroduodenoscopy probe insertion on the intracuff pressure of airway devices in children during general anesthesia.

PubMed

Balaban, Onur; Kamata, Mineto; Hakim, Mumin; Tumin, Dmitry; Tobias, Joseph D

2017-04-01

Given the size of the esophagogastroduodenoscopy (EGD) probe and the compressibility of the pediatric airway, the EGD probe may increase the intracuff pressure (IP) of an airway device. The current study evaluated IP changes during EGD examination under general anesthesia in pediatric patients. Following the induction of anesthesia, a laryngeal mask airway (LMA) or endotracheal tube (ETT) was placed without neuromuscular blockade. The IP was measured at baseline, during EGD probe insertion, while the EGD probe was in place, and after probe removal. The study cohort included 101 patients (mean age 11.3 years). The airway was secured with an LMA and an ETT in 88 and 13 patients, respectively. The IP increased from 27 ± 15 cmH 2 O at baseline to 34 ± 17 cmH 2 O during probe insertion (p < 0.001), remained at 33 ± 16 cmH 2 O while the probe was in place, and decreased to 26 ± 14 cmH 2 O after probe removal. The IP of the LMA or ETT increased during EGD probe insertion and remained elevated while the probe was in place. High IP may compromise mucosal perfusion resulting in a sore throat when using an LMA or the potential for airway damage if an ETT is used. Removal of air from the cuff and titration of the IP should be considered after EGD insertion.

A randomized prospective controlled trial comparing the laryngeal tube suction disposable and the supreme laryngeal mask airway: the influence of head and neck position on oropharyngeal seal pressure.

PubMed

Somri, Mostafa; Vaida, Sonia; Garcia Fornari, Gustavo; Mendoza, Gabriela Renee; Charco-Mora, Pedro; Hawash, Naser; Matter, Ibrahim; Swaid, Forat; Gaitini, Luis

2016-10-06

The Laryngeal Tube Suction Disposable (LTS-D) and the Supreme Laryngeal Mask Airway (SLMA) are second generation supraglottic airway devices (SADs) with an added channel to allow gastric drainage. We studied the efficacy of these devices when using pressure controlled mechanical ventilation during general anesthesia for short and medium duration surgical procedures and compared the oropharyngeal seal pressure in different head and-neck positions. Eighty patients in each group had either LTS-D or SLMA for airway management. The patients were recruited in two different institutions. Primary outcome variables were the oropharyngeal seal pressures in neutral, flexion, extension, right and left head-neck position. Secondary outcome variables were time to achieve an effective airway, ease of insertion, number of attempts, maneuvers necessary during insertion, ventilatory parameters, success of gastric tube insertion and incidence of complications. The oropharyngeal seal pressure achieved with the LTS-D was higher than the SLMA in, (extension (p=0.0150) and right position (p=0.0268 at 60 cm H 2 O intracuff pressures and nearly significant in neutral position (p = 0.0571). The oropharyngeal seal pressure was significantly higher with the LTS-D during neck extension as compared to SLMA (p= 0.015). Similar oropharyngeal seal pressures were detected in all other positions with each device. The secondary outcomes were comparable between both groups. Patients ventilated with LTS-D had higher incidence of sore throat (p = 0.527). No major complications occurred. Better oropharyngeal seal pressure was achieved with the LTS-D in head-neck right and extension positions , although it did not appear to have significance in alteration of management using pressure control mechanical ventilation in neutral position. The fiberoptic view was better with the SLMA. The post-operative sore throat incidence was higher in the LTS-D. ClinicalTrials.gov ID: NCT02856672 , Unique Protocol ID:BnaiZionMC-16-LG-001, Registered: August 2016.

Throat swab culture

MedlinePlus

... throat. It is most often used to diagnose strep throat . How the Test is Performed You will be ... done when a throat infection is suspected, particularly strep throat. A throat culture can also help your provider ...

Infections and foreign bodies in ENT.

PubMed

Kullar, Peter; Yates, Philip D

2012-10-30

Infections play a major role in the practice of ENT. Microbial penetration into tissues of the head and neck can initiate a focal reaction causing superficial self-resolving infections. However, some of these have the potential to develop into life-threatening disease. We provide an overview of the most common ENT infections with focus on the presentation, diagnosis and management. Foreign bodies of the ear, nose and throat are a common presentation to primary and emergency care. Most commonly these are seen in children and include plastic toys, beads and foodstuffs inserted into the ears and nose. Diagnosis is often delayed as insertion is usually not witnessed. In exceptional cases airway foreign bodies can present as a life-threatening emergency. Removal of foreign bodies can usually be achieved by a skilled practitioner with minimal complications. Methods of removal include suction catheters, syringing, and use of instrumentation. In adults, the treatment of oesophageal food bolus obstruction may require a combination of medical and surgical intervention.

Bottom-up approach for microstructure optimization of sound absorbing materials.

PubMed

Perrot, Camille; Chevillotte, Fabien; Panneton, Raymond

2008-08-01

Results from a numerical study examining micro-/macrorelations linking local geometry parameters to sound absorption properties are presented. For a hexagonal structure of solid fibers, the porosity phi, the thermal characteristic length Lambda('), the static viscous permeability k(0), the tortuosity alpha(infinity), the viscous characteristic length Lambda, and the sound absorption coefficient are computed. Numerical solutions of the steady Stokes and electrical equations are employed to provide k(0), alpha(infinity), and Lambda. Hybrid estimates based on direct numerical evaluation of phi, Lambda('), k(0), alpha(infinity), Lambda, and the analytical model derived by Johnson, Allard, and Champoux are used to relate varying (i) throat size, (ii) pore size, and (iii) fibers' cross-section shapes to the sound absorption spectrum. The result of this paper tends to demonstrate the important effect of throat size in the sound absorption level, cell size in the sound absorption frequency selectivity, and fibers' cross-section shape in the porous material weight reduction. In a hexagonal porous structure with solid fibers, the sound absorption level will tend to be maximized with a 48+/-10 microm throat size corresponding to an intermediate resistivity, a 13+/-8 microm fiber radius associated with relatively small interfiber distances, and convex triangular cross-section shape fibers allowing weight reduction.

Controlling the electronic and geometric structures of 2D insertions to realize high performance metal/insertion-MoS2 sandwich interfaces.

PubMed

Su, Jie; Feng, Liping; Zeng, Wei; Liu, Zhengtang

2017-06-08

Metal/insertion-MoS 2 sandwich interfaces are designed to reduce the Schottky barriers at metal-MoS 2 interfaces. The effects of geometric and electronic structures of two-dimensional (2D) insertion materials on the contact properties of metal/insertion-MoS 2 interfaces are comparatively studied by first-principles calculations. Regardless of the geometric and electronic structures of 2D insertion materials, Fermi level pinning effects and charge scattering at the metal/insertion-MoS 2 interface are weakened due to weak interactions between the insertion and MoS 2 layers, no gap states and negligible structural deformations for MoS 2 layers. The Schottky barriers at metal/insertion-MoS 2 interfaces are induced by three interface dipoles and four potential steps that are determined by the charge transfers and structural deformations of 2D insertion materials. The lower the electron affinities of 2D insertion materials, the more are the electrons lost from the Sc surface, resulting in lower n-type Schottky barriers at Sc/insertion-MoS 2 interfaces. The larger the ionization potentials and the thinner the thicknesses of 2D insertion materials, the fewer are the electrons that accumulate at the Pt surface, leading to lower p-type Schottky barriers at Pt/insertion-MoS 2 interfaces. All Sc/insertion-MoS 2 interfaces exhibited ohmic characters. The Pt/BN-MoS 2 interface exhibits the lowest p-type Schottky barrier of 0.52 eV due to the largest ionization potential (∼6.88 eV) and the thinnest thickness (single atomic layer thickness) of BN. These results in this work are beneficial to understand and design high performance metal/insertion-MoS 2 interfaces through 2D insertion materials.

The New Perilaryngeal Airway (CobraPLA™)1 Is as Efficient as the Laryngeal Mask Airway (LMA™)2, But Provides Better Airway Sealing Pressures

PubMed Central

Akça, Ozan; Wadhwa, Anupama; Sengupta, Papiya; Durrani, Jaleel; Hanni, Keith; Wenke, Mary; Yücel, Yüksel; Lenhardt, Rainer; Doufas, Anthony G.; Sessler, Daniel I.

2006-01-01

The Laryngeal Mask Airway (LMA) is a frequently-used efficient airway device, yet it sometimes seals poorly, thus reducing the efficacy of positive-pressure ventilation. The Perilaryngeal Airway (CobraPLA) is a novel airway device with a larger pharyngeal cuff (when inflated). We tested the hypothesis that the CobraPLA was superior to LMA with regard to insertion time and airway sealing pressure and comparable to LMA in airway adequacy and recovery characteristics. After midazolam and fentanyl, 81 ASA I-II outpatients having elective surgery were randomized to receive an LMA or CobraPLA. Anesthesia was induced with propofol (2.5 mg/kg, IV), and the airway inserted. We measured 1) insertion time; 2) adequacy of the airway (no leak at 15-cm-H2O peak pressure or tidal volume of 5 ml/kg); 3) airway sealing pressure; 4) number of repositioning attempts; and 5) sealing quality (no leak at tidal volume of 8 ml/kg). At the end of surgery, gastric insufflation, postoperative sore throat, dysphonia, and dysphagia were evaluated. Data were compared with unpaired t-tests, chi-square tests, or Fisher’s Exact tests; P<0.05 was significant. Patient characteristics, insertion times, airway adequacy, number of repositioning attempts, and recovery were similar in each group. Airway sealing pressure was significantly greater with CobraPLA (23±6 cm H2O) than LMA (18±5 cm H2O, P<0.001). The CobraPLA has insertion characteristics similar to LMA, but better airway sealing capabilities. PMID:15281543

Pore-wall roughness as a fractal surface and theoretical simulation of mercury intrusion/retraction in porous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsakiroglou, C.D.; Payatakes, A.C.

The mercury intrusion/retraction curves of many types of porous materials (e.g., sandstones) have sections of finite slope in the region of high and very high pressure. This feature is attributed to the existence of microroughness on the pore walls. In the present work pore-wall roughness features are added to a three-dimensional primary network of chambers-and-throats using ideas of fractal geometry. The roughness of the throats is modeled with a finite number of self-similar triangular prisms of progressively smaller sizes. The roughness of the chambers is modeled in a similar way using right circular cones instead of prisms. Three parameters sufficemore » for the complete characterization of the model of fractal roughness, namely, the number of features per unit length, the common angle of sharpness, and the number of layers (which is taken to be the same for throats and chambers). Analytical relations that give the surface area, pore volume, and mercury saturation of the pore network as functions of the fractal roughness parameters are developed for monolayer and multilayer arrangements. The chamber-and-throat network with fractal pore-wall roughness is used to develop an extended version of the computer-aided simulator of mercury porosimetry that has been reported in previous publications. This new simulator is used to investigate the effects of the roughness features on the form of mercury intrusion/retraction curves. It turns out that the fractal model of the porewall roughness gives an adequate representation of real porous media, and capillary pressure curves which are similar to the experimental ones for many typical porous materials such as sandstones. The method is demonstrated with the analysis of a Greek sandstone.« less

Efficacy of flurbiprofen 8.75 mg delivered as a spray or lozenge in patients with sore throat due to upper respiratory tract infection: a randomized, non-inferiority trial in the Russian Federation

PubMed Central

Radkova, Eugenia; Burova, Natalia; Bychkova, Valeria; DeVito, Robert

2017-01-01

Objective To assess the efficacy of flurbiprofen 8.75 mg delivered as a spray or lozenge in patients with sore throat due to upper respiratory tract infection (URTI). Materials and methods This multicenter, double-blind, double-dummy, non-inferiority study randomized 440 adults with recent-onset, moderate-to-severe sore throat due to URTI to a single dose of either flurbiprofen 8.75 mg spray (n=218) or flurbiprofen 8.75 mg lozenge (n=222). The presence or absence of beta-hemolytic streptococci (A or C) was confirmed by culture tests (throat swab). The primary efficacy end point was the difference from baseline to 2 hours post-dose in sore throat pain intensity scale (STPIS pain intensity difference [PID] 2h), a validated 100 mm visual analog scale (from 0=“no pain” to 100=“severe pain”), with a non-inferiority margin of −6 mm. Secondary end points included STPIS PID at 1 hour (STPIS PID 1h) and over 2 hours (STPIS sum of sore throat pain intensity differences [SPID]0–2h) and ratings of patient satisfaction and investigator assessment of drug efficacy at 2 hours. Safety (adverse events [AEs]) was also assessed. Results Reductions in sore throat pain intensity at 2 hours (STPIS PID 2h) were similar for spray (least square mean −40.51) and lozenge (−40.10) (difference: 0.41, 95% confidence interval [95% CI] −3.20, 4.01), with non-inferiority demonstrated. Subgroup analyses showed similar efficacy (STPIS PID 2h) for patients testing positive or negative for Strep A or C. There was no significant difference between spray and lozenge in STPIS PID 1h or STPIS SPID0–2h, and patient satisfaction and investigators’ assessment of efficacy at 2 hours were similar for both groups. There were no significant differences in AEs between the two groups, with 17 drug-related events across both groups, all being mild and none being serious. Conclusion Both formulations demonstrated comparable efficacy and safety profiles and provide patients with two different treatment formats to choose from for effective symptomatic relief of sore throat, depending on their preference. PMID:28740426

Ear, Nose and Throat Foreign Bodies Removed under General Anaesthesia: A Retrospective Study.

PubMed

Shunyu, Neizekhotuo Brian; Akhtar, Hanifa; Karim, Habib Md Rezaul; Lyngdoh, Nari M; Yunus, Md; Jamil, Md

2017-02-01

For Otorhinolaryngologist, removal of Foreign Bodies (FB) from the ear, nose and throat is one of the common emergency procedures done. Most of the cases especially of the ear and nose can be managed without General Anaesthesia (GA). But in some cases GA may be needed. There are very few studies that address the scenario of ear, nose and throat foreign body that required GA for its removal and the complications associated with it. This study was conducted with the aim to study the patient's profile, types and distribution of FB removed under GA, and the associated complications. The present study is a hospital based retrospective, cross-sectional study conducted in the Department of Otorhinolaryngology in association with Department of Anaesthesiology and Critical Care in North Eastern Indira Gandhi Regional Institute of Health and Medical Sciences, Shillong, Meghalaya, India from year 2009 to 2014. Information was collected from indoor patient file and operation record book. Those patients where foreign body was not found after examination under GA were excluded. A total of 112 cases of foreign body in ear, nose and throat removed under GA were selected. There was variation of age from youngest case being 11 months to 74 years with a slight male predominance. Two third of the patients belonged to paediatric age group. Most of the FB were inanimate with high number of inorganic type found in majority. Foreign body in food passage was found in most cases. Coin and meat bone were the common FB in children and adults respectively. We found no complications related to removal of foreign body from the food passage and nose. But some complications were seen in foreign body of ear and tracheo-bronchial tree. Ear, nose and throat FB that required GA were seen in all age groups. FB of food passage constitute the majority. Type of foreign body varies between children and adults. In children most common types were related to toys and their part and food materials. In adults, food materials were most common.

Method for improving the durability of ion insertion materials

DOEpatents

Lee, Se-Hee; Tracy, C. Edwin; Cheong, Hyeonsik M.

2002-01-01

The invention provides a method of protecting an ion insertion material from the degradative effects of a liquid or gel-type electrolyte material by disposing a protective, solid ion conducting, electrically insulating, layer between the ion insertion layer and the liquid or gel-type electrolyte material. The invention further provides liquid or gel-type electrochemical cells having improved durability having a pair of electrodes, a pair of ion insertion layers sandwiched between the pair of electrodes, a pair of solid ion conducting layers sandwiched between the ion insertion layers, and a liquid or gel-type electrolyte material disposed between the solid ion conducting layers, where the solid ion conducting layer minimizes or prevents degradation of the faces of the ion insertion materials facing the liquid or gel-type electrolyte material. Electrochemical cells of this invention having increased durability include secondary lithium batteries and electrochromic devices.

Shock-absorbing effect of shoe insert materials commonly used in management of lower extremity disorders.

PubMed

Shiba, N; Kitaoka, H B; Cahalan, T D; Chao, E Y

1995-01-01

The efficacy of 3 shock-absorbing materials was compared by determining impact characteristics with a drop test method and also by testing the effect of each material when used as a shoe insert in 16 asymptomatic subjects. Peak vertical ground reaction force (F1, F2, F3) and temporal force factors (T1, T2, T3) were obtained with a force plate at a high-frequency sampling rate. Impact force, impact time, impact slope, and impact energy were determined. A standard weight was dropped from 3 heights on each material covering the force plate while reduction of peak force was compared. Impact force was attenuated most effectively by Insert 3 (polymeric foam rubber) and averaged 11% less than that in shoes without inserts. Impact time was increased for all 3 inserts. Impact slope and impact energy were reduced significantly in Insert 3. There was a significant difference in peak vertical force F1 for all 3 inserts, in vertical force F2 for Insert 2 (viscoelastic polymeric material), and in vertical force F3 for Insert 2. Drop-test studies showed that at all ball heights, the highest mean peak force was observed consistently in Insert 2.

A study of the suitability of ferrite for use in low-field insertion devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, K.; Hassenzahl, W.V.

1995-02-01

Most insertion devices built to date use rare-earth permanent-magnet materials, which have a high remanent field and are more expensive than many other permanent-magnet materials. Low-field insertion devices could use less-expensive, lower performance magnetic materials if they had suitable magnetic characteristics. These materials must be resistant to demagnetization during construction and operation of the insertion device, have uniform magnetization, possess low minor-axis magnetic moments, and have small minor field components on the surfaces. This paper describes an investigation to determine if ferrite possesses magnetic qualities suitable for insertion device applications. The type of ferrite investigated, MMPA Ceramic 8 from Stackpolemore » Inc., was found to be acceptable for insertion device applications.« less

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter. Preliminary settling and resuspension testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Fowley, M. D.; Miller, D. H.

2016-05-01

The full-scale, room-temperature Hanford Tank Waste Treatment and Immobilization Plant (WTP) High-Level Waste (HLW) melter riser test system was successfully operated with silicone oil and magnetite particles at a loading of 0.1 vol %. Design and construction of the system and instrumentation, and the selection and preparation of simulant materials, are briefly reviewed. Three experiments were completed. A prototypic pour rate was maintained, based on the volumetric flow rate. Settling and accumulation of magnetite particles were observed at the bottom of the riser and along the bottom of the throat after each experiment. The height of the accumulated layer atmore » the bottom of the riser, after the first pouring experiment, approximated the expected level given the solids loading of 0.1 vol %. More detailed observations of particle resuspension and settling were made during and after the third pouring experiment. The accumulated layer of particles at the bottom of the riser appeared to be unaffected after a pouring cycle of approximately 15 minutes at the prototypic flow rate. The accumulated layer of particles along the bottom of the throat was somewhat reduced after the same pouring cycle. Review of the time-lapse recording showed that some of the settling particles flow from the riser into the throat. This may result in a thicker than expected settled layer in the throat.« less

Self-pressurized air-Q® intubating laryngeal airway versus the LMA® Classic™: a randomized clinical trial.

PubMed

Ha, Sang Hee; Kim, Min-Soo; Suh, Jiwoo; Lee, Jong Seok

2018-05-01

The self-pressurized air-Q® (air-Q SP) intubating laryngeal airway is a relatively new supraglottic airway (SGA) device. The intracuff pressure of air-Q dynamically equilibrates with the airway pressure and adjusts to the patient's pharyngeal and periglottic anatomy, potentially providing improved airway fit and seal. The aim of this prospective randomized study was to compare the clinical performance of air-Q to the LMA® Classic™ SGA. Adult patients requiring general anesthesia for elective surgery were prospectively enrolled and randomly assigned to either air-Q SP or the LMA Classic SGA. Oropharyngeal leak pressure (primary endpoint), success rate, insertion features (insertion time, ease of insertion, requirement for device manipulation), sealing function, gastric insufflation, bronchoscopic view, and oropharyngeal complications at device insertion and following its removal (sore throat, dysphagia, dysphonia) were compared. The mean (standard deviation [SD]) oropharyngeal leak pressure just after insertion was similar in the air-Q SP and LMA [16.8 (4.9) vs 18.6 (5.5) cm H 2 O, respectively; mean difference, 1.8 cm H 2 O; 95% CI, -0.5 to 4.2; P = 0.13] and did not differ at ten minutes following device insertion. Median [interquartile range (IQR)] peak inspiratory pressure just after insertion was lower in the air-Q SP (11.0 [10.0-13.0] vs 13.0 [11.0-14.0] cmH 2 O, median difference, 1.0 cm H 2 O; 95% CI, 0.0 to 2.0; P = 0.03) but no difference was observed at ten minutes. The median [IQR] insertion time was faster with the air-Q SP (15.9 [13.6-20.3] sec vs 24 [21.2-27.1] sec; median difference, 8.1 sec; 95% CI, 5.6 to 9.9; P < 0.001) and improved bronchoscopic viewing grade were seen with the air-Q SP immediately after insertion (P < 0.001). No differences between the groups were observed with respect to the rate of successful insertion at first attempt, overall insertion success rate, ease of insertion, and complications. The air-Q SP had similar leak pressures but a faster insertion time and superior bronchoscopic viewing grade when compared with the LMA Classic. The air-Q SP is a suitable alternative to the LMA Classic in adult patients and may be a superior conduit for tracheal intubation. www.clinicaltrials.gov (NCT02206438). Registered 1 August 2014.

Sore Throat

MedlinePlus

... and mononucleosis) can lead to a sore throat. Bacteria (such as those that cause strep throat) can ... each side of your throat) become infected by bacteria or a virus. It causes the tonsils to ...

Efficacy of flurbiprofen 8.75 mg lozenge in patients with a swollen and inflamed sore throat.

PubMed

Aspley, Sue; Shephard, Adrian; Schachtel, Emily; Sanner, Kathleen; Savino, Laurie; Schachtel, Bernard

2016-09-01

Sore throat is often over-treated with antibiotics, therefore there is a need for non-antibiotic treatments that provide effective relief. From the patient's point of view, symptoms of pharyngeal inflammation such as a "swollen" and "inflamed" throat are often considered the most bothersome; so, a non-steroidal anti-inflammatory drug could be an appropriate treatment. We investigated the efficacy and safety of flurbiprofen 8.75 mg lozenge in adults with a swollen and inflamed throat. We enrolled adults with moderate-to-severe sore throat and evidence of tonsillo-pharyngitis into a randomized, double-blind study. Patients received flurbiprofen 8.75 mg or placebo lozenges every 3-6 hours as needed (up to five lozenges in 24 hours) and rated their symptoms (sore throat pain, difficulty swallowing and the sensation of a swollen throat) on standard linear scales regularly over 24 hours. The efficacy of flurbiprofen lozenge was determined in patients reporting a swollen and inflamed throat at baseline, as well as those with relatively severe symptoms. ClinicalTrials.gov NCT01049334. The main outcome measures were the time-weighted summed differences in patient-reported sore throat pain, difficulty swallowing and swollen throat over 24 hours. Out of 204 patients, 124 (60.8%) described their throats as swollen and inflamed at baseline. Flurbiprofen lozenges provided greater relief than placebo over 24 hours: 79.8%, 99.6% and 69.3% (for sore throat pain, difficulty swallowing and swollen throat, respectively, all P ≤ 0.01). These outcomes were more substantial in patients with relatively severe symptoms. No serious or unexpected adverse events occurred. Flurbiprofen 8.75 mg lozenge appears to provide effective, well-tolerated relief of sore throat, difficulty swallowing and swollen throat in adults with a swollen and inflamed throat, as well as those with relatively severe symptoms. A limitation of these findings is that, while predetermined, these are secondary outcomes derived from a targeted sub-group of patients, not the entire study population.

Crank shaft support assembly

DOEpatents

Natkin, Robert J.; Oltmans, Bret; Allison, John E.; Heater, Thomas J.; Hines, Joy Adair; Tappen, Grant K.; Peiskammer, Dietmar

2007-10-23

A crank shaft support assembly for increasing stiffness and reducing thermal mismatch distortion in a crank shaft bore of an engine comprising different materials. A cylinder block comprises a first material and at least two crank journal inserts are insert-molded into respective crank journal regions of the cylinder block and comprise a second material having greater stiffness and a lower thermal coefficient of expansion that the first material. At least two bearing caps are bolted to the respective crank journal inserts and define, along with the crank journal inserts, at least two crank shaft support rings defining a crank shaft bore coaxially aligned with a crank shaft axis. The bearing caps comprise a material having higher stiffness and a lower thermal coefficient of expansion than the first material and are supported on the respective crank journal inserts independently of any direct connection to the cylinder block.

Throat infections are associated with exacerbation in a substantial proportion of patients with chronic plaque psoriasis

PubMed Central

Thorleifsdottir, Ragna H.; Eysteinsdottir, Jenna H.; Olafsson, Jon H.; Sigurdsson, Martin I.; Johnston, Andrew; Valdimarsson, Helgi; Sigurgeirsson, Bardur

2016-01-01

Streptococcal throat infections are known to trigger or exacerbate psoriasis, and several studies support the benefit of tonsillectomy. To evaluate the potential of tonsillectomy as a treatment, we used a retrospective study-specific questionnaire to assess the proportion of psoriasis patients with sore throat-associated psoriasis exacerbations. Our survey sampled 275 psoriasis patients. 42% of patients with plaque psoriasis reported sore throat-associated psoriasis exacerbations, and 72% of patients with confirmed streptococcal infections reported aggravation. Notably, women and early onset psoriasis patients were more likely to report psoriasis exacerbation after a sore throat (p<0.001, p=0.046 respectively). Other psoriasis aggravation factors were more common in patients with sore throat-associated exacerbations (p<0.01). 49% of tonsillectomized patients reported subsequent improvement and had more frequent sore throat-associated aggravation of psoriasis than patients who did not improve after tonsillectomy (p=0.015). These findings suggest a closer association between sore throats, streptococcal throat infections and plaque psoriasis than previously reported. PMID:26984718

Throat Infections are Associated with Exacerbation in a Substantial Proportion of Patients with Chronic Plaque Psoriasis.

PubMed

Thorleifsdottir, Ragna H; Eysteinsdóttir, Jenna H; Olafsson, Jón H; Sigurdsson, Martin I; Johnston, Andrew; Valdimarsson, Helgi; Sigurgeirsson, Bardur

2016-08-23

Streptococcal throat infections are known to trigger or exacerbate psoriasis, and several studies support the benefit of tonsillectomy. To evaluate the potential of tonsillectomy as a treatment, we used a retrospective study-specific questionnaire to assess the proportion of psoriasis patients with sore throat-associated psoriasis exacerbations. Our survey sampled 275 psoriasis patients. Of patients with plaque psoriasis, 42% reported sore throat-associated psoriasis exacerbations, and of patients with confirmed streptococcal infections, 72% reported aggravation. Notably, women and patients with early onset psoriasis were more likely to report psoriasis exacerbation after a sore throat (p < 0.001, p = 0.046, respectively). Other psoriasis aggravation factors were more common in patients with sore throat-associated exacerbations (p < 0.01). Of tonsillectomized patients, 49% reported subsequent improvement and had more frequent sore throat-associated aggravation of psoriasis than patients who did not improve after tonsillectomy (p = 0.015). These findings suggest a closer association between sore throats, streptococcal throat infections and plaque psoriasis than reported previously.

21 CFR 874.4780 - Intranasal splint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4780 Intranasal splint. (a) Identification... septum and the nasal cavity. It is placed in the nasal cavity after surgery or trauma. The intranasal splint is constructed from plastic, silicone, or absorbent material. (b) Classification. Class I (general...

21 CFR 874.4780 - Intranasal splint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4780 Intranasal splint. (a) Identification... septum and the nasal cavity. It is placed in the nasal cavity after surgery or trauma. The intranasal splint is constructed from plastic, silicone, or absorbent material. (b) Classification. Class I (general...

21 CFR 874.4780 - Intranasal splint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4780 Intranasal splint. (a) Identification... septum and the nasal cavity. It is placed in the nasal cavity after surgery or trauma. The intranasal splint is constructed from plastic, silicone, or absorbent material. (b) Classification. Class I (general...

21 CFR 874.4780 - Intranasal splint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4780 Intranasal splint. (a) Identification... septum and the nasal cavity. It is placed in the nasal cavity after surgery or trauma. The intranasal splint is constructed from plastic, silicone, or absorbent material. (b) Classification. Class I (general...

21 CFR 874.4780 - Intranasal splint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... DEVICES EAR, NOSE, AND THROAT DEVICES Surgical Devices § 874.4780 Intranasal splint. (a) Identification... septum and the nasal cavity. It is placed in the nasal cavity after surgery or trauma. The intranasal splint is constructed from plastic, silicone, or absorbent material. (b) Classification. Class I (general...

Flurbiprofen 8.75 mg lozenges for treating sore throat symptoms: a randomized, double-blind, placebo-controlled study.

PubMed

Schachtel, Bernard P; Shephard, Adrian; Shea, Timothy; Sanner, Kathleen; Savino, Laurie; Rezuke, Jeanne; Schachtel, Emily; Aspley, Sue

2016-11-01

This study assessed multiple doses of flurbiprofen 8.75 mg lozenges for the relief of three prominent symptoms of acute pharyngitis: pain intensity (primary end point), difficulty swallowing and swollen throat. A total of 204 patients (102 in each group) with confirmed pharyngitis (onset ≤4 days) were randomly assigned to take up to five flurbiprofen or placebo lozenges every 3-6 h, for 7 days. Using validated rating scales (sore throat pain intensity, difficulty swallowing and swollen throat) patients rated their symptoms for the duration of the study. Over the first 24 h, patients treated with flurbiprofen lozenges reported significantly greater reductions in sore throat pain (47%) as well as difficulty swallowing (66%) and swollen throat (40%) compared with placebo (all p < 0.05). Multiple doses of flurbiprofen lozenges provide effective relief of sore throat pain intensity as well as difficulty swallowing and swollen throat.

The rational clinical examination. Does this patient have strep throat?

PubMed

Ebell, M H; Smith, M A; Barry, H C; Ives, K; Carey, M

2000-12-13

Sore throat is a common complaint, and identifying patients with group A beta-hemolytic streptococcal pharyngitis (strep throat) is an important task for clinicians. Previous reviews have not systematically reviewed and synthesized the evidence. To review the precision and accuracy of the clinical examination in diagnosing strep throat. MEDLINE search for articles about diagnosis of strep throat using history-taking and physical examination. Large blinded, prospective studies (having > or =300 patients with sore throat) reporting history and physical examination data and using throat culture as the reference standard were included. Of 917 articles identified by the search, 9 met all inclusion criteria. Pairs of authors independently reviewed each article and used consensus to resolve discrepancies. The most useful findings for evaluating the likelihood of strep throat are presence of tonsillar exudate, pharyngeal exudate, or exposure to strep throat infection in the previous 2 weeks (positive likelihood ratios, 3.4, 2.1, and 1.9, respectively) and the absence of tender anterior cervical nodes, tonsillar enlargement, or exudate (negative likelihood ratios, 0.60, 0.63, and 0.74, respectively). No individual element of history-taking or physical examination is accurate enough by itself to rule in or rule out strep throat. Three validated clinical prediction rules are described for adult and pediatric populations. While no single element of history-taking or physical examination is sufficiently accurate to exclude or diagnose strep throat, a well-validated clinical prediction rule can be useful and can help physicians make more informed use of rapid antigen tests and throat cultures.

Mechanical trapping of particles in granular media

NASA Astrophysics Data System (ADS)

Kerimov, Abdulla; Mavko, Gary; Mukerji, Tapan; Al Ibrahim, Mustafa A.

2018-02-01

Mechanical trapping of fine particles in the pores of granular materials is an essential mechanism in a wide variety of natural and industrial filtration processes. The progress of invading particles is primarily limited by the network of pore throats and connected pathways encountered by the particles during their motion through the porous medium. Trapping of invading particles is limited to a depth defined by the size, shape, and distribution of the invading particles with respect to the size, shape, and distribution of the host porous matrix. Therefore, the trapping process, in principle, can be used to obtain information about geometrical properties, such as pore throat and particle size, of the underlying host matrix. A numerical framework is developed to simulate the mechanical trapping of fine particles in porous granular media with prescribed host particle size, shape, and distribution. The trapping of invading particles is systematically modeled in host packings with different host particle distributions: monodisperse, bidisperse, and polydisperse distributions of host particle sizes. Our simulation results show quantitatively and qualitatively to what extent trapping behavior is different in the generated monodisperse, bidisperse, and polydisperse packings of spherical particles. Depending on host particle size and distribution, the information about extreme estimates of minimal pore throat sizes of the connected pathways in the underlying host matrix can be inferred from trapping features, such as the fraction of trapped particles as a function of invading particle size. The presence of connected pathways with minimum and maximum of minimal pore throat diameters can be directly obtained from trapping features. This limited information about the extreme estimates of pore throat sizes of the connected pathways in the host granular media inferred from our numerical simulations is consistent with simple geometrical estimates of extreme value of pore and throat sizes of the densest structural arrangements of spherical particles and geometrical Delaunay tessellation analysis of the pore space of host granular media. Our results suggest simple relations between the host particle size and trapping features. These relationships can be potentially used to describe both the dynamics of the mechanical trapping process and the geometrical properties of the host granular media.

Mechanical trapping of particles in granular media.

PubMed

Kerimov, Abdulla; Mavko, Gary; Mukerji, Tapan; Al Ibrahim, Mustafa A

2018-02-01

Mechanical trapping of fine particles in the pores of granular materials is an essential mechanism in a wide variety of natural and industrial filtration processes. The progress of invading particles is primarily limited by the network of pore throats and connected pathways encountered by the particles during their motion through the porous medium. Trapping of invading particles is limited to a depth defined by the size, shape, and distribution of the invading particles with respect to the size, shape, and distribution of the host porous matrix. Therefore, the trapping process, in principle, can be used to obtain information about geometrical properties, such as pore throat and particle size, of the underlying host matrix. A numerical framework is developed to simulate the mechanical trapping of fine particles in porous granular media with prescribed host particle size, shape, and distribution. The trapping of invading particles is systematically modeled in host packings with different host particle distributions: monodisperse, bidisperse, and polydisperse distributions of host particle sizes. Our simulation results show quantitatively and qualitatively to what extent trapping behavior is different in the generated monodisperse, bidisperse, and polydisperse packings of spherical particles. Depending on host particle size and distribution, the information about extreme estimates of minimal pore throat sizes of the connected pathways in the underlying host matrix can be inferred from trapping features, such as the fraction of trapped particles as a function of invading particle size. The presence of connected pathways with minimum and maximum of minimal pore throat diameters can be directly obtained from trapping features. This limited information about the extreme estimates of pore throat sizes of the connected pathways in the host granular media inferred from our numerical simulations is consistent with simple geometrical estimates of extreme value of pore and throat sizes of the densest structural arrangements of spherical particles and geometrical Delaunay tessellation analysis of the pore space of host granular media. Our results suggest simple relations between the host particle size and trapping features. These relationships can be potentially used to describe both the dynamics of the mechanical trapping process and the geometrical properties of the host granular media.

Structure of the effective potential for a spherical wormhole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montelongo Garcia, N.; Zannias, T.

2008-09-15

The structure of the effective potential V describing causal geodesics near the throat of an arbitrary spherical wormhole is analyzed. Einstein's equations relative to a set of regular coordinates covering a vicinity of the throat imply that any spherical wormhole can be constructed from solutions of an effective initial value problem with the throat serving as an initial value surface. The initial data involve matter variables, the area A(0) of the throat, and the gradient {lambda}(0) of the redshift factor on the throat. Whenever {lambda}(0)=0, the effective potential V has a critical point on the throat. Conditions upon the datamore » are derived ensuring that the critical point is a local minimum (respectively maximum). For particular families of quasi-Schwarzschild wormholes, V exhibits a local minimum on the throat independently upon the energy E and angular momentum L{sup 2} of the test particles and thus such wormholes admit stable circular timelike and null geodesics on the throat. For families of Chaplygin wormholes, we show that such geodesics are unstable. Based on a suitable power series representation of the metric, properties of V away from the throat are obtained that are useful for the analysis of accretion disks and radiation processes near the throat of any spherical wormhole.« less

Controlled overspray spray nozzle

NASA Technical Reports Server (NTRS)

Prasthofer, W. P. (Inventor)

1981-01-01

A spray system for a multi-ingredient ablative material wherein a nozzle A is utilized for suppressing overspray is described. The nozzle includes a cyclindrical inlet which converges to a restricted throat. A curved juncture between the cylindrical inlet and the convergent portion affords unrestricted and uninterrupted flow of the ablative material. A divergent bell-shaped chamber and adjustable nozzle exit B is utilized which provides a highly effective spray pattern in suppressing overspray to an acceptable level and producing a homogeneous jet of material that adheres well to the substrate.

Insert Concepts for the Material Science Research Rack (MSRR-1) of the Material Science Research Facility (MSRF) on the International Space Station (ISS)

NASA Technical Reports Server (NTRS)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

2000-01-01

The Material Science Research Rack I (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit NASA's planned inserts include the Quench Module Insert (QMI) and the Diffusion Module Insert (DMI). The QMI is a high-gradient Bridgman-type vacuum furnace with quench capabilities used for experiments on directional solidification of metal alloys. The DMI is a vacuum Bridgman-Stockbarger-type furnace for experiments on Fickian and Soret diffusion in liquids. This paper discusses specific design features and performance capabilities of each insert. The paper also presents current prototype QMI hardware analysis and testing activities and selected results.

Bitter-type toroidal field magnet for zephyr

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathrath, N.; Keinath, W.; Kobusch, W.

1981-09-01

A feasibility study concerning stress computations, design and material technology of a Bitter-type magnet for the ZEPHYR project conducted in West Germany is reported. The big overall dimensions of the magnet (6.50 m diam 2.80 m high), access for diagnostics and neutral injection (16 ports), the possibility of remote handling of activated parts and high forces form the main requirements for design and material. A design with 16 identical modules (coils) was chosen, each coil consisting of 16 Bitter plates, plate housings and one diagnostic/neutral injection wedge. The structural parts are connected by bolts and form the bending stiff structuremore » of the magnet. The most critical area of the magnet is the inner wedge-shaped part of the coils (''throat area'') with extremely high tension, compression and shear stress values, to which temperature effects contribute heavily. Steel-copper compounds are found to be the best Bitter-plate materials. Copper-plating austenitic steel can be done galvanically or by explosive techniques. Cold-worked austenitic steels fulfil the requirements in the throat, in the flat-plate region milder steels can be used. Different plate concepts are being considered. Plasma-sprayed Al/sub 2/O/sub 3//TiO/sub 2/ and reinforced epoxy layers are provided as insulating materials in different magnet areas.« less

Ceramic backup ring prevents undesirable weld-metal buildup

NASA Technical Reports Server (NTRS)

Leonard, G. E.

1971-01-01

Removable ceramic backup material butted against weld zone back prevents weld metal buildup at that site. Method is successful with manual tungsten-inert gas /TIG/ welding of 316 corrosion resistant steel /CRES/ pieces with 0.76 cm throat diameter and 1.57 cm pipe internal diameter.

Utility of the sore throat pain model in a multiple-dose assessment of the acute analgesic flurbiprofen: a randomized controlled study.

PubMed

Schachtel, Bernard; Aspley, Sue; Shephard, Adrian; Shea, Timothy; Smith, Gary; Schachtel, Emily

2014-07-03

The sore throat pain model has been conducted by different clinical investigators to demonstrate the efficacy of acute analgesic drugs in single-dose randomized clinical trials. The model used here was designed to study the multiple-dose safety and efficacy of lozenges containing flurbiprofen at 8.75 mg. Adults (n=198) with moderate or severe acute sore throat and findings of pharyngitis on a Tonsillo-Pharyngitis Assessment (TPA) were randomly assigned to use either flurbiprofen 8.75 mg lozenges (n=101) or matching placebo lozenges (n=97) under double-blind conditions. Patients sucked one lozenge every three to six hours as needed, up to five lozenges per day, and rated symptoms on 100-mm scales: the Sore Throat Pain Intensity Scale (STPIS), the Difficulty Swallowing Scale (DSS), and the Swollen Throat Scale (SwoTS). Reductions in pain (lasting for three hours) and in difficulty swallowing and throat swelling (for four hours) were observed after a single dose of the flurbiprofen 8.75 mg lozenge (P<0.05 compared with placebo). After using multiple doses over 24 hours, flurbiprofen-treated patients experienced a 59% greater reduction in throat pain, 45% less difficulty swallowing, and 44% less throat swelling than placebo-treated patients (all P<0.01). There were no serious adverse events. Utilizing the sore throat pain model with multiple doses over 24 hours, flurbiprofen 8.75 mg lozenges were shown to be an effective, well-tolerated treatment for sore throat pain. Other pharmacologic actions (reduced difficulty swallowing and reduced throat swelling) and overall patient satisfaction from the flurbiprofen lozenges were also demonstrated in this multiple-dose implementation of the sore throat pain model. This trial was registered with ClinicalTrials.gov, registration number: NCT01048866, registration date: January 13, 2010.

De-agglomeration Effect of the US Pharmacopeia and Alberta Throats on Carrier-Based Powders in Commercial Inhalation Products.

PubMed

Leung, Sharon Shui Yee; Tang, Patricia; Zhou, Qi Tony; Tong, Zhenbo; Leung, Cassandra; Decharaksa, Janwit; Yang, Runyu; Chan, Hak-Kim

2015-11-01

The US pharmacopeia (USP) and Alberta throats were recently reported to cause further de-agglomeration of carrier-free powders emitted from some dry powder inhalers (DPIs). This study assessed if they have similar influences on commercially available carrier-based DPIs. A straight tube, a USP throat, and an Alberta throat (non-coated and coated) were used for cascade impaction testing. Aerosol fine particle fraction (FPF ≤ 5 μm) was computed to evaluate throat-induced de-agglomeration. Computational fluid dynamics are employed to simulate airflow patterns and particle trajectories inside the USP and Alberta throats. For all tested products, no significant differences in the in vitro aerosol performance were observed between the USP throat and the straight tube. Using fine lactose carriers (<10 μm), Symbicort(®) and Oxis(™) showed minimal impaction inside the Alberta throat and resulted in similar FPF among all induction ports. For products using coarse lactose carriers (>10 μm), impaction frequency and energy inside the Alberta throat were significant. Further de-agglomeration was noted inside the non-coated Alberta throat for Seretide(®) and Spiriva(®), but agglomerates emitted from Relenza(®), Ventolin(®), and Foradil(®) did not further break up into smaller fractions. The coated Alberta throat considerably reduced the FPF values of these products due to the high throat retention, but they generally agreed better with the in vivo data. In conclusion, depending on the powder formulation (including carrier particle size), the inhaler, and the induction port, further de-agglomeration could happen ex-inhaler and create differences in the in vitro measurements.

'Black universe' epoch in string cosmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchel, Alex; Perimeter Institute for Theoretical Physics, Waterloo, Ontario, N2J 2W9; Kofman, Lev

2008-10-15

String theory compactification involves manifolds with multiple warp factors. For cosmological applications, we often introduce a short, high-energy inflationary throat, and a long, low-energy standard model (SM) throat. It is assumed that at the end of inflation, the excited Kaluza-Klein modes from the inflationary throat tunnel to the SM throat and reheat standard model degrees of freedom, which are attached to probe brane(s). However, the huge hierarchy of energy scales can result in a highly dynamic transition of the throat geometry. We point out that in such a cosmological scenario the standard model throat (together with SM brane) will bemore » cloaked by a Schwarzschild horizon, produced by the Kaluza-Klein modes tunneling from the short throat. The black brane formation is dual to the first order chiral phase transition of the cascading gauge theory. We calculate the critical energy density corresponding the formation of the black hole (BH) horizon in the long throat. We discuss the duality between 'black universe' cosmology and an expanding universe driven by the hot gauge theory radiation. We address the new problem of the hierarchical multiple-throat scenarios: SM brane disappearance after the decay of the BH horizon.« less

Comparison of postoperative complication between Laryngeal Mask Airway and endotracheal tube during low-flow anesthesia with controlled ventilation

PubMed Central

Peirovifar, Ali; Eydi, Mahmood; Mirinejhad, Mir Mousa; Mahmoodpoor, Ata; Mohammadi, Afsaneh; EJ Golzari, Samad

2013-01-01

Objective: To compare the postoperative complications between Laryngeal Mask Airway (LMA) and endotracheal tube (ETT) during low-flow anesthesia with controlled ventilation. Methodology: Eighty adult Patients with ASA class I or II were randomly allocated into two forty-patient groups (ETT or LMA). Cuff pressure was monitored during anesthesia. After high uptake period, fresh gas flow (FGF) was decreased to 1 lit/min and isoflurane set to 1%. Monitoring during anesthesia included non-invasive blood pressure, ECG, ETCO2 and pulse oximetry. System leakage (>100 ml/min), rebreathing and any attempt to increase FGF to overcome the leak were monitored during anesthesia. Later, patients were extubated and transferred to Post Anesthesia Care Unit (PACU). In PACU, the incidence of sore throat, cough, difficulty in swallowing and shivering was monitored for all patients. Results: Leakage was observed in two and three cases in ETT and LMA groups respectively (P>0.05). Postoperative cough, sore throat and difficulty in swallowing were significantly less in LMA than ETT group. No significant difference was observed regarding ETCo2 values between 2 groups. Conclusion: If careful measures regarding insertion techniques, correct LMA position and routine monitoring of LMA cuff pressure are taken, LMA can be used as a safe alternative with lower incidence of post operation complication compared with ETT during low-flow controlled anesthesia with modern anesthetic machines. PMID:24353586

An inexpensive method for quantifying incubation patterns of open-cup nesting birds, with data for black-throated Blue warblers

USGS Publications Warehouse

Joyce, Elizabeth M.; Sillett, T. Scott; Holmes, Richard T.

2001-01-01

Quantifying incubation patterns has often involved long observation periods in the field, video cameras, or the use of other electronic devices that sometimes require the partial destruction of clutches and insertion of artificial eggs. In this study, we used an inexpensive, nondestructive method involving temperature probes combined with data loggers to examine the incubation rhythm of female Black-throated Blue Warblers (Dendroica caerulescens). The method provided detailed records of on–off patterns for females for selected 24-h periods during incubation. Female warblers spent an average (±SE) of 64.0% of daylight hours incubating in bouts lasting 20.5 ± 1.5 min and made 2.4 ± 0.1 departures from the nest/h on trips that lasted 10.6 ± 0.7 min. Incubation bouts were longer and females spent more time incubating per hour in the mornings and late afternoons than at mid-day. Older females had longer incubation bouts and tended to have shorter incubation periods than did yearling females, suggesting that experienced individuals were more effective incubators. Because of its ease of use and because nests with probes were not depredated at a higher rate than controls, we suggest that the temperature probe/data logger method is an efficient and effective way to quantify incubation rhythms for open-cup nesting birds.

Throat Swabs and Sputum Culture as Predictors of P. aeruginosa or S. aureus Lung Colonization in Adult Cystic Fibrosis Patients.

PubMed

Seidler, Darius; Griffin, Mary; Nymon, Amanda; Koeppen, Katja; Ashare, Alix

2016-01-01

Due to frequent infections in cystic fibrosis (CF) patients, repeated respiratory cultures are obtained to inform treatment. When patients are unable to expectorate sputum, clinicians obtain throat swabs as a surrogate for lower respiratory cultures. There is no clear data in adult subjects demonstrating the adequacy of throat swabs as a surrogate for sputum or BAL. Our study was designed to determine the utility of throat swabs in identifying lung colonization with common organisms in adults with CF. Adult CF subjects (n = 20) underwent bronchoscopy with BAL. Prior to bronchoscopy, a throat swab was obtained. A sputum sample was obtained from subjects who were able to spontaneously expectorate. All samples were sent for standard microbiology culture. Using BAL as the gold standard, we found the positive predictive value for Pseudomonas aeruginosa to be 100% in both sputum and throat swab compared to BAL. However, the negative predictive value for P. aeruginosa was 60% and 50% in sputum and throat swab, respectively. Conversely, the positive predictive value for Staphylococcus aureus was 57% in sputum and only 41% in throat swab and the negative predictive value of S. aureus was 100% in sputum and throat swab compared to BAL. Our data show that positive sputum and throat culture findings of P. aeruginosa reflect results found on BAL fluid analysis, suggesting these are reasonable surrogates to determine lung colonization with P. aeruginosa. However, sputum and throat culture findings of S. aureus do not appear to reflect S. aureus colonization of the lung.

Flurbiprofen microgranules for relief of sore throat: a randomised, double-blind trial

PubMed Central

Russo, Marc; Bloch, Mark; de Looze, Fred; Morris, Christopher; Shephard, Adrian

2013-01-01

Background Many people with sore throat seek, and are often inappropriately prescribed, antibiotics. Aim The objective of this study was to determine the analgesic efficacy of flurbiprofen 8.75 mg microgranules versus placebo. These microgranules are a possible alternative treatment for patients with sore throat due to upper respiratory tract infection (URTI). Design and setting Randomised, double-blind, placebo-controlled, multiple-dose study conducted at eight primary care sites in Australia. Method Participants with sore throat of onset within the past 4 days received either flurbiprofen 8.75 mg microgranules or non-medicated placebo microgranules. Throat soreness, difficulty in swallowing, sore throat pain intensity, sore throat relief, oral temperature, and treatment benefits were all assessed at regular intervals. Result Of 373 patients from eight centres, 186 received flurbiprofen 8.75 mg microgranules and 187 received placebo microgranules (intent-to-treat population). Throat soreness was significantly reduced over the first 2 hours after the first dose. Reductions in difficulty in swallowing were observed at all time points from 5 to 360 minutes after the first dose, after taking flurbiprofen microgranules versus placebo. Sore throat relief was also evident at 1 minute and lasted for at least 6 hours. The multiple-dose efficacy results showed reduction of difficulty in swallowing at the end of days 1–3 and sore throat relief at the end of day 1. Conclusion Microgranules containing flurbiprofen 8.75 mg provided fast and effective relief from sore throat due to URTI and represent an alternative treatment option to antibiotic therapy. PMID:23561694

Characterization of the performance of shoe insert materials.

PubMed

Lewis, G; Tan, T; Shiue, Y S

1991-08-01

It has been widely reported that shoe inserts are an effective interventional modality either for the relief of discomfort to the feet associated with a variety of orthopedic disorders or conditions or simply for comfort. Results from many types of experimental tests have been used to obtain the shock absorption capacity of shoe insert materials. The authors contend in this study that, while shock absorption is a highly desirable property, it is by no means the only that should be used to characterize these materials. Thus, a new index of performance of these materials is proposed. This index is computed from data, obtained in a simple experimental test, on both the shock absorption and energy return performances of the insert material.

Analysis of cured carbon-phenolic decomposition products to investigate the thermal decomposition of nozzle materials

NASA Technical Reports Server (NTRS)

Thompson, James M.; Daniel, Janice D.

1989-01-01

The development of a mass spectrometer/thermal analyzer/computer (MS/TA/Computer) system capable of providing simultaneous thermogravimetry (TG), differential thermal analysis (DTA), derivative thermogravimetry (DTG) and evolved gas detection and analysis (EGD and EGA) under both atmospheric and high pressure conditions is described. The combined system was used to study the thermal decomposition of the nozzle material that constitutes the throat of the solid rocket boosters (SRB).

Comparison between Indirect Immunofluorescence Assay and Shell Vial Culture for Detection of Mumps Virus from Clinical Samples

PubMed Central

Reina, Jordi; Ballesteros, Francisca; Ruiz de Gopegui, Enrique; Munar, Maria; Mari, Margarita

2003-01-01

We report a prospective comparison of the efficacies of an indirect immunofluorescence assay (IFA) and shell vial culture (SVC) of throat swab and urine samples from patients with mumps. Throat swab samples were used for the IFA; the urine samples and throat swabs were inoculated into vials of Vero cells. We studied 62 patients by using 62 throat swabs and 50 urine samples (50 patients with both samples). Sixty (96.7%) throat samples were positive in the SVC, and 61 (98.3%) were positive in the IFA. For the 50 patients from whom both samples were available, the IFA was positive in 50 (100%) cases, the urine sample was positive in 49 (98%) cases, and the throat swab was positive in 48 (96%) cases (P > 0.05). This comparison of throat swabs and urine samples has shown that the two clinical samples are similar in efficacy. PMID:14605158

Finite Element Simulation of Solid Rocket Booster Separation Motors During Motor Firing

NASA Technical Reports Server (NTRS)

Yu. Weiping; Crane, Debora J.

2007-01-01

One of the toughest challenges facing Solid Rocket Booster (SRB) engineers is to ensure that any design changes made to the Shuttle-Derived Booster Separation Motors (BSM) for future space exploration vehicles is able to withstand the increasingly hostile motor firing environment without cracking its critical component - the graphite throat. This paper presents a critical analysis methodology and techniques for assessing effects of BSM design changes with great accuracy and precision. For current Space Shuttle operation, the motor firing occurs at SRB separation - approximately 125 seconds after Shuttle launch at an altitude of about 28 miles. The motor operation event lasts about two seconds, however, the surface temperature of the graphite throat increases approximately 3400 F in less than one second with a corresponding increase in surface pressure of approximately 2200 pounds per square inch (psi) in less than one-tenth of a second. To capture this process fully and accurately, a two-phase sequentially coupled thermal-mechanical finite element approach was developed. This method allows the time- and location-dependent pressure fields to interact with the spatial-temporal thermal fields throughout the operation. The material properties of graphite throat are orthotropic and temperature-dependent. The analysis involves preload and multiple body contacts.

Throat swabs have no influence on the management of patients with sore throats.

PubMed

Cheung, L; Pattni, V; Peacock, P; Sood, S; Gupta, D

2017-11-01

Throat swabs are neither specific nor sensitive for micro-bacteria causing sore throat symptoms; however, current guidelines suggest they are still useful in some cases. Retrospective and prospective analyses were conducted of throat swabs requested within the months of January 2016 and August 2016, respectively. The study comprised 247 patients. Fifty-nine (24 per cent) had a positive culture. Forty-six grew group A beta-haemolytic streptococci, with the remainder growing candida (n = 10), coliform (n = 1) and klebsiella (n = 2). There was no significant difference in culture rates between primary or secondary care sources (χ2 = 0.56, p = 0.45). None of the swabs influenced a variation in patient management from local antimicrobial policies. Current practice has an estimated annual financial impact of £3 434 340 on the National Health Service. Throat swabs do not influence the antimicrobial treatment for patients with sore throats, even under current guidelines, and incur unnecessary cost. Current clinical guidelines could be reviewed to reduce the number of throat swabs being conducted unnecessarily.

Recent developments in turning hardened steels - A review

NASA Astrophysics Data System (ADS)

Sivaraman, V.; Prakash, S.

2017-05-01

Hard materials ranging from HRC 45 - 68 such as hardened AISI H13, AISI 4340, AISI 52100, D2 STL, D3 STEEL Steel etc., need super hard tool materials to machine. Turning of these hard materials is termed as hard turning. Hard turning makes possible direct machining of the hard materials and also eliminates the lubricant requirement and thus favoring dry machining. Hard turning is a finish turning process and hence conventional grinding is not required. Development of the new advanced super hard tool materials such as ceramic inserts, Cubic Boron Nitride, Polycrystalline Cubic Boron Nitride etc. enabled the turning of these materials. PVD and CVD methods of coating have made easier the production of single and multi layered coated tool inserts. Coatings of TiN, TiAlN, TiC, Al2O3, AlCrN over cemented carbide inserts has lead to the machining of difficult to machine materials. Advancement in the process of hard machining paved way for better surface finish, long tool life, reduced tool wear, cutting force and cutting temperatures. Micro and Nano coated carbide inserts, nanocomposite coated PCBN inserts, micro and nano CBN coated carbide inserts and similar developments have made machining of hardened steels much easier and economical. In this paper, broad literature review on turning of hardened steels including optimizing process parameters, cooling requirements, different tool materials etc., are done.

Passive Rocket Diffuser Theory: A Re-Examination of Minimum Second Throat Size

NASA Technical Reports Server (NTRS)

Jones, Daniel R.

2016-01-01

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure during testing without using active control systems. Among the most critical design parameters is the relative area of the diffuser throat to that of the nozzle throat. A smaller second throat is generally desirable because it decreases the stagnation-to-ambient pressure ratio the diffuser requires for nominal operation. There is a limit, however. Below a certain size, the second throat can cause pressure buildup within the diffuser and prevent it from reaching the start condition that protects the nozzle from side-load damage. This paper presents a method for improved estimation of the minimum second throat area which enables diffuser start. The new 3-zone model uses traditional quasi-one-dimensional compressible flow theory to approximate the structure of two distinct diffuser flow fields observed in Computational Fluid Dynamics (CFD) simulations and combines them to provide a less-conservative estimate of the second throat size limit. It is unique among second throat sizing methods in that it accounts for all major conical nozzle and second throat diffuser design parameters within its limits of application. The performance of the 3-zone method is compared to the historical normal shock and force balance methods, and verified against a large number of CFD simulations at specific heat ratios of 1.4 and 1.25. Validation is left as future work, and the model is currently intended to function only as a first-order design tool.

Streptococcus A in paediatric accident and emergency: are rapid streptococcal tests and clinical examination of any help?

PubMed

Van Limbergen, J; Kalima, P; Taheri, S; Beattie, T F

2006-01-01

Rapid streptococcal tests (RSTs) for streptococcal pharyngitis have made diagnosis at once simpler and more complicated. The American Academy of Pediatrics recommends that all RSTs be confirmed by a follow up throat culture unless local validation has proved the RST to be equally sensitive. To evaluate (a) RST as a single diagnostic tool, compared with RST with or without throat culture; (b) clinical diagnosis and the relative contribution of different symptoms. The study included 213 patients with clinical signs of pharyngitis. Throat swabs were analysed using Quickvue+ Strep A Test; negative RSTs were backed up by throat culture. Thirteen clinical features commonly associated with strep throat were analysed using backward stepwise logistic regression. Positive results (RST or throat culture) were obtained in 33 patients; RST correctly identified 21. Eleven samples were false negative on RST. At a strep throat prevalence of 15.9%, sensitivity of RST was 65.6% (95% CI 46.8% to 81.4%) and specificity 99.4% (96.7% to 99.9%). Sensitivity of clinical diagnosis alone was 57% (34% to 78%) and specificity 71% (61% to 80%). Clinically, only history of sore throat, rash, and pyrexia contributed to the diagnosis of strep throat (p<0.05). The high specificity of RST facilitates early diagnosis of strep throat. However, the low sensitivity of RST does not support its use as a single diagnostic tool. The sensitivity in the present study is markedly different from that reported by the manufacturer. Clinical examination is of limited value in the diagnosis of strep throat. It is important to audit the performance of new diagnostic tests, previously validated in different settings.

Streptococcus A in paediatric accident and emergency: are rapid streptococcal tests and clinical examination of any help?

PubMed Central

Van Limbergen, J; Kalima, P; Taheri, S; Beattie, T F

2006-01-01

Background Rapid streptococcal tests (RSTs) for streptococcal pharyngitis have made diagnosis at once simpler and more complicated. The American Academy of Pediatrics recommends that all RSTs be confirmed by a follow up throat culture unless local validation has proved the RST to be equally sensitive. Aims To evaluate (a) RST as a single diagnostic tool, compared with RST with or without throat culture; (b) clinical diagnosis and the relative contribution of different symptoms. Methods The study included 213 patients with clinical signs of pharyngitis. Throat swabs were analysed using Quickvue+ Strep A Test; negative RSTs were backed up by throat culture. Thirteen clinical features commonly associated with strep throat were analysed using backward stepwise logistic regression. Results Positive results (RST or throat culture) were obtained in 33 patients; RST correctly identified 21. Eleven samples were false negative on RST. At a strep throat prevalence of 15.9%, sensitivity of RST was 65.6% (95% CI 46.8% to 81.4%) and specificity 99.4% (96.7% to 99.9%). Sensitivity of clinical diagnosis alone was 57% (34% to 78%) and specificity 71% (61% to 80%). Clinically, only history of sore throat, rash, and pyrexia contributed to the diagnosis of strep throat (p<0.05). Conclusion The high specificity of RST facilitates early diagnosis of strep throat. However, the low sensitivity of RST does not support its use as a single diagnostic tool. The sensitivity in the present study is markedly different from that reported by the manufacturer. Clinical examination is of limited value in the diagnosis of strep throat. It is important to audit the performance of new diagnostic tests, previously validated in different settings. PMID:16373800

Effects of different types of pharyngeal packing in patients undergoing nasal surgery: A comparative study.

PubMed

Rizvi, Mohd Meesam; Singh, Raj Bahadur; Rasheed, Mohd Asim; Sarkar, Arindam

2015-01-01

Postoperative throat complaints such as postoperative sore throat (POST), dysphagia, and hoarseness frequently arises after tracheal intubation and throat packing for patient undergoing general anesthesia. This condition is very disturbing to patient. Avoiding POST is a major priority for these patients because preventing postoperative complications contributes to patient satisfaction. To describe and analyze the postoperative throat effects of nasopharyngeal packing and oropharyngeal packing in patients undergoing nasal surgery. A randomized comparative study. After obtaining approval of Ethical Committee 40 patients were included in study. After this patient were randomly allocated into two groups of 20 each. Group A - in which the oropharynx was packed and Group B - inwhich the nasopharynx was packed. General anesthesia were given and throat packing was done and patients were interviewed postoperatively for any throat complications such as sore throat, difficulty in swallowing (dysphagia), hoarseness of voice, throat irritation, and any other symptom pertaining to the study were noted and data were analyzed. T-test to compare the age, while Chi-square test and Fisher's exact test were used to compare sex distribution, sore throat, dysphagia, hoarseness, and throat irritation. Results showed statistically significant difference in incidence and severity of POST in Group A patients when compared to Group B patients to be more. Patients in Group A had a higher incidence of dysphagia when compared to their Group B counterparts. With respect to the incidence of hoarseness and throat irritation, there was no statistical significance between the groups. We concluded that the site of pharyngeal packing influences the incidence and severity of POST and as well as the incidence of dysphagia after general anesthesia. The use of nasopharyngeal packing in the patients undergoing nasal surgeries might lead to a reduction of the same.

Influence of throat configuration and fish density on escapement of channel catfish from hoop nets

USGS Publications Warehouse

Porath, Mark T.; Pape, Larry D.; Richters, Lindsey K.

2011-01-01

In recent years, several state agencies have adopted the use of baited, tandemset hoop nets to assess lentic channel catfish Ictalurus punctatus populations. Some level of escapement from the net is expected because an opening exists in each throat of the net, although factors influencing rates of escapement from hoop nets have not been quantified. We conducted experiments to quantify rates of escapement and to determine the influence of throat configuration and fish density within the net on escapement rates. An initial experiment to determine the rate of escapement from each net compartment utilized individually tagged channel catfish placed within the entrance (between the two throats) and cod (within the second throat) compartments of a single hoop net for overnight sets. From this experiment, the mean rate (±SE) of channel catfish escaping was 4.2% (±1.5) from the cod (cod throat was additionally restricted from the traditionally manufactured product), and 74% (±4.2) from the entrance compartments. In a subsequent experiment, channel catfish were placed only in the cod compartment with different throat configurations (restricted or unrestricted) and at two densities (low [6 fish per net] and high [60 fish per net]) for overnight sets to determine the influence of fish density and throat configuration on escapement rates. Escapement rates between throat configurations were doubled at low fish density (13.3 ± 5.4% restricted versus 26.7 ± 5.6% unrestricted) and tripled at high fish density (14.3 ± 4.9% restricted versus 51.9 ± 5.0% unrestricted). These results suggest that retention efficiency is high from cod compartments with restricted throat entrances. However, managers and researchers need to be aware that modification to the cod throats (restrictions) is needed for hoop nets ordered from manufacturers. Managers need to be consistent in their use and reporting of cod end throat configurations when using this gear.

Utility of the sore throat pain model in a multiple-dose assessment of the acute analgesic flurbiprofen: a randomized controlled study

PubMed Central

2014-01-01

Background The sore throat pain model has been conducted by different clinical investigators to demonstrate the efficacy of acute analgesic drugs in single-dose randomized clinical trials. The model used here was designed to study the multiple-dose safety and efficacy of lozenges containing flurbiprofen at 8.75 mg. Methods Adults (n = 198) with moderate or severe acute sore throat and findings of pharyngitis on a Tonsillo-Pharyngitis Assessment (TPA) were randomly assigned to use either flurbiprofen 8.75 mg lozenges (n = 101) or matching placebo lozenges (n = 97) under double-blind conditions. Patients sucked one lozenge every three to six hours as needed, up to five lozenges per day, and rated symptoms on 100-mm scales: the Sore Throat Pain Intensity Scale (STPIS), the Difficulty Swallowing Scale (DSS), and the Swollen Throat Scale (SwoTS). Results Reductions in pain (lasting for three hours) and in difficulty swallowing and throat swelling (for four hours) were observed after a single dose of the flurbiprofen 8.75 mg lozenge (P <0.05 compared with placebo). After using multiple doses over 24 hours, flurbiprofen-treated patients experienced a 59% greater reduction in throat pain, 45% less difficulty swallowing, and 44% less throat swelling than placebo-treated patients (all P <0.01). There were no serious adverse events. Conclusions Utilizing the sore throat pain model with multiple doses over 24 hours, flurbiprofen 8.75 mg lozenges were shown to be an effective, well-tolerated treatment for sore throat pain. Other pharmacologic actions (reduced difficulty swallowing and reduced throat swelling) and overall patient satisfaction from the flurbiprofen lozenges were also demonstrated in this multiple-dose implementation of the sore throat pain model. Trial registration This trial was registered with ClinicalTrials.gov, registration number: NCT01048866, registration date: January 13, 2010. PMID:24988909

Plasma spray nozzle with low overspray and collimated flow

NASA Technical Reports Server (NTRS)

Beason, Jr., George P. (Inventor); McKechnie, Timothy N. (Inventor); Power, Christopher A. (Inventor)

1996-01-01

An improved nozzle for reducing overspray in high temperature supersonic plasma spray devices comprises a body defining an internal passageway having an upstream end and a downstream end through which a selected plasma gas is directed. The nozzle passageway has a generally converging/diverging Laval shape with its upstream end converging to a throat section and its downstream end diverging from the throat section. The upstream end of the passageway is configured to accommodate a high current cathode for producing an electrical arc in the passageway to heat and ionize the gas flow to plasma form as it moves along the passageway. The downstream end of the nozzle is uniquely configured through the methodology of this invention to have a contoured bell-shape that diverges from the throat to the exit of the nozzle. Coating material in powder form is injected into the plasma flow in the region of the bell-shaped downstream end of the nozzle and the powder particles become entrained in the flow. The unique bell shape of the nozzle downstream end produces a plasma spray that is ideally expanded at the nozzle exit and thus virtually free of shock phenomena, and that is highly collimated so as to exhibit significantly reduced fanning and diffusion between the nozzle and the target. The overall result is a significant reduction in the amount of material escaping from the plasma stream in the form of overspray and a corresponding improvement in the cost of the coating operation and in the quality and integrity of the coating itself.

Effect of Pneumoperitoneum and Lateral Position on Oropharyngeal Seal Pressures of Proseal LMA in Laparoscopic Urological Procedures.

PubMed

Rustagi, Preeti; Patkar, Geeta A; Ourasang, Anil Kumar; Tendolkar, Bharati A

2017-02-01

A sustained and effective oropharyngeal sealing with supraglottic airway is required to maintain the ventilation during laparoscopic surgery. Previous studies have observed the Oropharyngeal Seal Pressure (OSP) for Proseal Laryngeal Mask Airway (PLMA) after pneumoperitoneum in supine and trendelenburg position, where PLMA was found to be an effective airway device. This study was conducted with ProSeal LMA, for laparoscopic Urologic procedures done in lateral position. To measure OSP in supine and lateral position and to observe the effect of pneumoperitoneum in lateral position on OSP. Secondary objectives were to assess adequacy of ventilation and incidence of adverse events. A total number of 25 patients of American Society of Anaesthesiologists (ASA) physical status II and I were enrolled. After induction of anaesthesia using a standardized protocol, PLMA was inserted. Ryle's tube was inserted through drain tube. The position of PLMA was confirmed with ease of insertion of Ryle's tube and fibreoptic grading of vocal cords. Patients were then put in lateral position. The OSP was measured in supine position. This value was baseline comparison for OSP in lateral position and that after pneumoperitoneum. We assessed the efficacy of PLMA for ventilation, after carboperitoneum in lateral position (peak airway pressure, End Tidal Carbon dioxide (EtCO 2 ), SPO 2 ). Incidence of adverse effects (displacement of device, gastric insufflation, regurgitation, coughing, sore throat, blood on device, trauma) was also noted. The OSP was above Peak Airway Pressure (PAP) in supine (22.1±5.4 and 15.4±4.49cm of H 2 O) and lateral position (22.6±5.3 and 16.1±4.6). After pneumoperitoneum, which was in lateral position, there was statistically significant (p-value <0.05) increase in both PAP (19.96±4.015) and OSP (24.32±4.98, p-value 0.03). There was no intraoperative displacement of PLMA. There was no event of suboptimal oxygenation. EtCO 2 was always within normal limits. Gastric insufflation was present in one patient. One patient had coughing and blood was detected on device. Three patients had throat discomfort post-operatively. In this study, Oropharyngeal seal pressures with PLMA were found to increase after pneumoperitoneum in lateral position. PLMA forms an effective seal around airway and is an efficient and safe alternative for airway management in urological laparoscopic surgeries done in lateral position.

Hoarseness

MedlinePlus

... as fever, cough, sore throat, difficulty swallowing, weight loss, or fatigue? You may have one or more of the following tests: Laryngoscopy Throat culture Throat examination with a small mirror X-rays ...

Risk factors for otolaryngological foreign bodies in Eastern Poland.

PubMed

Rybojad, Beata; Niedzielski, Artur; Niedzielska, Grazyna; Rybojad, Pawel

2012-11-01

To identify the sociodemographic characteristics and risk factors associated with suspected foreign bodies in the ear, nose, throat, airway, and esophagus among Polish children. Case series with chart review. Setting Tertiary care medical center. A retrospective analysis of the medical records of patients hospitalized for a suspected foreign body (FB) between 1998 and 2008 was conducted. Data regarding place of residence, presence of siblings, parents' educational status, seasonality, psychomotor development, age, and sex were collected and statistically analyzed. Of the 1011 patients with suspected foreign body insertion, 849 (84%) had a positive diagnosis. Of the confirmed foreign bodies, 96 were found in the tracheobronchial tree, 142 were found in the esophagus, and 611 were located in the external auditory canals, nasopharyngeal passage, tonsils, auricles, or lips. Sociodemographically, 596 of the children came from urban areas, with a preponderance of males (55%). Objects were removed more frequently in summer and autumn (60%). Children with siblings (53%) predominated. The majority of patients (52%) had parents with an elementary education. Food was the most frequent foreign body in children under 3 years of age. Patients with delayed psychomotor development constituted 1.6% of the analyzed population. Being male, 1 to 3 years of age, belonging to an urban family with siblings, and having parents with an elementary education increased the risk of foreign body insertion. Training caregivers about proper nutrition and safety rules when playing with children can reduce the risk of accidents related to foreign body insertion.

Guideline for the management of acute sore throat.

PubMed

Pelucchi, C; Grigoryan, L; Galeone, C; Esposito, S; Huovinen, P; Little, P; Verheij, T

2012-04-01

The European Society for Clinical Microbiology and Infectious Diseases established the Sore Throat Guideline Group to write an updated guideline to diagnose and treat patients with acute sore throat. In diagnosis, Centor clinical scoring system or rapid antigen test can be helpful in targeting antibiotic use. The Centor scoring system can help to identify those patients who have higher likelihood of group A streptococcal infection. In patients with high likelihood of streptococcal infections (e.g. 3-4 Centor criteria) physicians can consider the use of rapid antigen test (RAT). If RAT is performed, throat culture is not necessary after a negative RAT for the diagnosis of group A streptococci. To treat sore throat, either ibuprofen or paracetamol are recommended for relief of acute sore throat symptoms. Zinc gluconate is not recommended to be used in sore throat. There is inconsistent evidence of herbal treatments and acupuncture as treatments for sore throat. Antibiotics should not be used in patients with less severe presentation of sore throat, e.g. 0-2 Centor criteria to relieve symptoms. Modest benefits of antibiotics, which have been observed in patients with 3-4 Centor criteria, have to be weighed against side effects, the effect of antibiotics on microbiota, increased antibacterial resistance, medicalisation and costs. The prevention of suppurative complications is not a specific indication for antibiotic therapy in sore throat. If antibiotics are indicated, penicillin V, twice or three times daily for 10 days is recommended. At the present, there is no evidence enough that indicates shorter treatment length. © 2012 The Authors. Clinical Microbiology and Infection © 2012 European Society of Clinical Microbiology and Infectious Diseases.

Materials property definition and generation for carbon-carbon and carbon phenolic materials

NASA Technical Reports Server (NTRS)

Canfield, A. R.; Mathis, J. R.; Starrett, H. S.; Koenig, J. R.

1987-01-01

A data base program to generate statistically significant material-property data for carbon-carbon and carbon phenolic materials to be used in designs of Space Shuttle is described. The program, which will provide data necessary for thermal and stress modeling of Shuttle nozzle and exit cone structures, includes evaluation of tension, compression, shear strength, shear modulus, thermal expansion, thermal conductivity, permeability, and emittance for both materials; the testing of carbon phenolic materials also includes CTE, off-gassing, pyrolysis, and RTG. Materials to be tested will be excised from Space Shuttle inlet, throat, and exit cone billets and modified involute carbon-carbon exit cones; coprocessed blocks, panels, and cylinders will also be tested.

Meaningful relief with flurbiprofen 8.75 mg spray in patients with sore throat due to upper respiratory tract infection.

PubMed

de Looze, Ferdinandus; Russo, Marc; Bloch, Mark; Montgomery, Barney; Shephard, Adrian; DeVito, Robert

2018-03-01

Evaluate the efficacy of flurbiprofen 8.75 mg spray for sore throat relief. Randomized, double-blind study in adults with sore throat due to upper respiratory tract infection who took flurbiprofen (n = 249) or placebo spray (n = 256). Pain relief was assessed using the Sore Throat Relief Rating Scale. Flurbiprofen spray provided significantly greater relief versus placebo from 20 min to 6 h (p < 0.0001; maximum difference: 75 min). Sore throat severity was reduced ≥-2.2 on the Sore Throat Scale from 75 min to 6 h, indicating meaningful relief. Significantly more patients taking flurbiprofen spray reported ≥30 min of 'at least moderate' relief versus placebo over 6 h (p < 0.0001). Most adverse events were mild. Flurbiprofen spray provides rapid, long-lasting and clinically meaningful relief from sore throat (ANZCTR: ACTRN12612000457842).

Streptococcal Infections

MedlinePlus

... Group A strep causes Strep throat - a sore, red throat. Your tonsils may be swollen and have ... illness that follows strep throat. It causes a red rash on the body. Impetigo - a skin infection ...

-dimensional thin shell wormhole with deformed throat can be supported by normal matter

NASA Astrophysics Data System (ADS)

Mazharimousavi, S. Habib; Halilsoy, M.

2015-06-01

From the physics standpoint the exotic matter problem is a major difficulty in thin shell wormholes (TSWs) with spherical/cylindrical throat topologies. We aim to circumvent this handicap by considering angle dependent throats in dimensions. By considering the throat of the TSW to be deformed spherical, i.e., a function of and , we present general conditions which are to be satisfied by the shape of the throat in order to have the wormhole supported by matter with positive density in the static reference frame. We provide particular solutions/examples to the constraint conditions.

Throat or larynx cancer

MedlinePlus

Vocal cord cancer; Throat cancer; Laryngeal cancer; Cancer of the glottis; Cancer of oropharynx or hypopharynx ... use tobacco are at risk of developing throat cancer. Drinking too much alcohol over a long time ...

Incidence, causes, severity and treatment of throat discomfort: a four-region online questionnaire survey

PubMed Central

2012-01-01

Background Acute sore throat is commonly associated with viral infections. Consumers typically rely on over-the-counter treatments and other remedies to treat symptoms; however, limited information is available regarding consumer perceptions of sore throat or treatment needs. The aim of this study was to investigate perceptions of throat discomfort and how these influence attitudes and consumer behaviour with regard to treatment. Methods Online consumer surveys were completed by participants invited by email between 2003 and 2004 in four markets: the UK, France, Poland, and Malaysia. The questionnaire consisted of 24 questions that covered key issues surrounding throat discomfort including incidence in the past 12 months, causes, severity, effects on functionality and quality of life, actions taken to relieve throat discomfort, the efficacy of these approaches and the reasons behind using specific products. Results In total, 6465 men and women aged ≥18 years were surveyed, identifying 3514 participants who had suffered throat discomfort/irritation in the past 12 months (response rate of 54%). These participants completed the full survey. The breakdown of throat discomfort sufferers was: UK, 912; France, 899; Poland, 871; Malaysia, 832. A high proportion of respondents experienced one or more instances of throat discomfort in the previous 12 months, with an overall incidence of 54%. Infections including the common cold/influenza and other bacteria/viruses were commonly perceived causes of throat discomfort (72% and 46%, respectively). Physical and environmental factors were also perceived to be causative, including airborne pollution (28%), smoking (23%), and air conditioning (31%). Symptoms perceived to be caused by an infection were associated with a higher degree of suffering (mean degree of suffering for bacteria/virus and common cold/influenza; 3.4 and 3.0, respectively). Medicinal products were used for all perceived causes, but more commonly for sore throats thought to be caused by infections. Cold drinks were used more often for symptoms thought to be due to physical and environmental causes. Conclusions Not all throat discomfort is the same, as demonstrated by the range of perceived causes and the emotional and physical symptoms experienced. Patient expectations regarding treatment of throat discomfort differs and treatments should be tailored by pharmacists to suit the cause. PMID:22883470

A multicentre, randomised, double-blind, single-dose study assessing the efficacy of AMC/DCBA Warm lozenge or AMC/DCBA Cool lozenge in the relief of acute sore throat

PubMed Central

2011-01-01

Background Clinically proven over-the-counter (OTC) treatment options are becoming increasingly important in the self-management of acute sore throat. The aim of this study was to determine the analgesic and sensorial benefits of two different amylmetacresol/2,4-dichlorobenzyl alcohol (AMC/DCBA) throat lozenge formulation variants, AMC/DCBA Warm lozenge and AMC/DCBA Cool lozenge, compared with an unflavoured, non-medicated placebo lozenge in the relief of acute sore throat due to upper respiratory tract infections. Methods In this multicentre, randomised, double-blind, single-dose study, 225 adult patients with acute sore throat were randomly assigned to receive either one AMC/DCBA Warm lozenge (n = 77), one AMC/DCBA Cool lozenge (n = 74) or one unflavoured, non-medicated lozenge (matched for size, shape and demulcency; n = 74). After baseline assessments, patients received their assigned lozenge and completed four rating assessments at 11 timepoints from 1 to 120 minutes post dose. Analgesic properties were assessed by comparing severity of throat soreness and sore throat relief ratings. Difficulty in swallowing, throat numbness, functional, sensorial and emotional benefits were also assessed. Results Both the AMC/DCBA Warm and AMC/DCBA Cool lozenge induced significant analgesic, functional, sensorial and emotional effects compared with the unflavoured, non-medicated lozenge. Sore throat relief, improvements in throat soreness and difficulty in swallowing, and throat numbness were observed as early as 1-5 minutes, and lasted up to 2 hours post dose. Sensorial benefits of warming and cooling associated with the AMC/DCBA Warm and AMC/DCBA Cool lozenge, respectively, were experienced soon after first dose, and in the case of the latter, it lasted long after the lozenge had dissolved. Emotional benefits of feeling better, happier, less distracted and less frustrated were reported in those taking either of the AMC/DCBA throat lozenge variants, with no differences in adverse events compared with the unflavoured, non-medicated lozenge. Conclusions AMC/DCBA Warm and AMC/DCBA Cool lozenges are well-tolerated and effective OTC treatment options, offering functional, sensorial and emotional benefits to patients with acute sore throat, over and above that of the rapid efficacy effects provided. Trial registration ISRCTN: ISRCTN00003567 PMID:21332976

Assessment of Creep Deformation, Damage, and Rupture Life of 304HCu Austenitic Stainless Steel Under Multiaxial State of Stress

NASA Astrophysics Data System (ADS)

Sahoo, K. C.; Goyal, Sunil; Parameswaran, P.; Ravi, S.; Laha, K.

2018-03-01

The role of the multiaxial state of stress on creep deformation and rupture behavior of 304HCu austenitic stainless steel was assessed by performing creep rupture tests on both smooth and notched specimens of the steel. The multiaxial state of stress was introduced by incorporating circumferential U-notches of different root radii ranging from 0.25 to 5.00 mm on the smooth specimens of the steel. Creep tests were carried out at 973 K over the stress range of 140 to 220 MPa. In the presence of notch, the creep rupture strength of the steel was found to increase with the associated decrease in rupture ductility. Over the investigated stress range and notch sharpness, the strengthening was found to increase drastically with notch sharpness and tended toward saturation. The fractographic studies revealed the mixed mode of failure consisting of transgranular dimples and intergranular creep cavitation for shallow notches, whereas the failure was predominantly intergranular for relatively sharper notches. Detailed finite element analysis of stress distribution across the notch throat plane on creep exposure was carried out to assess the creep failure of the material in the presence of notch. The reduction in von-Mises stress across the notch throat plane, which was greater for sharper notches, increased the creep rupture strength of the material. The variation in fracture behavior of the material in the presence of notch was elucidated based on the von-Mises, maximum principal, and hydrostatic stresses. Electron backscatter diffraction analysis of creep strain distribution across the notch revealed localized creep straining at the notch root for sharper notches. A master curve for predicting creep rupture life under the multiaxial state of stress was generated considering the representative stress having contributions from both the von-Mises and principal stress components of the stress field in the notch throat plane. Rupture ductility was also predicted based on the multiaxial state of stress.

Sore Throat (For Parents)

MedlinePlus

... another illness, like a cold , the flu , or mononucleosis . They also can be caused by a strep ... topic for: Parents Kids Teens Strep Throat Coughing Mononucleosis Strep Test: Rapid Strep Test: Throat Culture Flu ...

21 CFR 201.315 - Over-the-counter drugs for minor sore throats; suggested warning.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Over-the-counter drugs for minor sore throats... Drug Products § 201.315 Over-the-counter drugs for minor sore throats; suggested warning. The Food and... counter for the relief of minor irritations of the mouth or throat. It will not object to the labeling of...

21 CFR 201.315 - Over-the-counter drugs for minor sore throats; suggested warning.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 4 2011-04-01 2011-04-01 false Over-the-counter drugs for minor sore throats... Drug Products § 201.315 Over-the-counter drugs for minor sore throats; suggested warning. The Food and... counter for the relief of minor irritations of the mouth or throat. It will not object to the labeling of...

Prevention of Influenza and other Respiratory Diseases

DTIC Science & Technology

1977-08-01

Virus isolation was attempted from throat washings collected in beef extract broth. These were stored at approximately -50 In a refrigerator at Lowry... throat cultures and blood specimens with individual Informed consent. Cooperation was remarkably good. Throat cultures were taken from...more rapidly in Rhesus monkey kidney tissue culture than did the A/Denver/77 strains. Viruses were isolated from 9 of 13 throat washings from

School Nurses on the Front Lines of Medicine: A Student With Fever and Sore Throat.

PubMed

Olympia, Robert P

2016-05-01

Fever and sore throat are common chief complaints encountered by school nurses. This article explains the etiology of both fever and sore throat in children, describes the office assessment, and delineates life-threatening complications associated with fever and sore throat that may prompt the school nurse to transfer the child to a local emergency department. © 2016 The Author(s).

Randomised, double-blind, placebo-controlled studies on flurbiprofen 8.75 mg lozenges in patients with/without group A or C streptococcal throat infection, with an assessment of clinicians' prediction of 'strep throat'.

PubMed

Shephard, A; Smith, G; Aspley, S; Schachtel, B P

2015-01-01

Diagnosing group A streptococcus (Strep A) throat infection by clinical examination is difficult, and misdiagnosis may lead to inappropriate antibiotic use. Most patients with sore throat seek symptom relief rather than antibiotics, therefore, therapies that relieve symptoms should be recommended to patients. We report two clinical trials on the efficacy and safety of flurbiprofen 8.75 mg lozenge in patients with and without streptococcal sore throat. The studies enrolled adults with moderate-to-severe throat symptoms (sore throat pain, difficulty swallowing and swollen throat) and a diagnosis of pharyngitis. The practitioner assessed the likelihood of Strep A infection based on historical and clinical findings. Patients were randomised to flurbiprofen 8.75 mg or placebo lozenges under double-blind conditions and reported the three throat symptoms at baseline and at regular intervals over 24 h. A total of 402 patients received study medication (n = 203 flurbiprofen, n = 199 placebo). Throat culture identified Strep A in 10.0% of patients and group C streptococcus (Strep C) in a further 14.0%. The practitioners' assessments correctly diagnosed Strep A in 11/40 cases (sensitivity 27.5%, and specificity 79.7%). A single flurbiprofen lozenge provided significantly greater relief than placebo for all three throat symptoms, lasting 3-4 h for patients with and without Strep A/C. Multiple doses of flurbiprofen lozenges over 24 h also led to symptom relief, although not statistically significant in the Strep A/C group. There were no serious adverse events. The results highlight the challenge of identifying Strep A based on clinical features. With the growing problem of antibiotic resistance, non-antibiotic treatments should be considered. As demonstrated here, flurbiprofen 8.75 mg lozenges are an effective therapeutic option, providing immediate and long-lasting symptom relief in patients with and without Strep A/C infection. © 2014 John Wiley & Sons Ltd.

What is LPR (Laryngopharyngeal Reflux)

MedlinePlus

... What role does an ear, nose, and throat specialist have in treating LPR? Laryngopharyngeal reflux (LPR) is ... by an otolaryngologist or ear, nose, and throat specialist. Symptoms related to LPR including throat discomfort, laryngitis, ...

Tonsillitis (For Parents)

MedlinePlus

... streptococci bacteria are causing the infection. If it's strep throat , your child will need treatment with an antibiotic ... Tonsils and Tonsillectomies Peritonsillar Abscess Strep Test: Rapid Strep Throat Strep Test: Throat Culture Enlarged Adenoids Having Your ...

Antibiotics for preventing recurrent sore throat.

PubMed

Ng, Gareth J Y; Tan, Stephanie; Vu, Anh N; Del Mar, Chris B; van Driel, Mieke L

2015-07-14

Antibiotics are sometimes used to prevent recurrent sore throat, despite concern about resistance. However, there is conflicting primary evidence regarding their effectiveness. To assess the effects of antibiotics in patients with recurrent sore throat. The Cochrane Ear, Nose and Throat Disorders Group (CENTDG) Trials Search Co-ordinator searched the CENTDG Trials Register; Central Register of Controlled Trials (CENTRAL 2015, Issue 5); PubMed; EMBASE; CINAHL; Web of Science; Clinicaltrials.gov; ICTRP and additional sources for published and unpublished trials. The date of the search was 25 June 2015. Randomised controlled trials (RCTs) of antibiotics in adults and children suffering from pre-existing recurrent sore throat, defined as three or more sore throats in a year, examining the incidence of sore throat recurrence, with follow-up of at least 12 months post-antibiotic therapy. Two authors independently assessed trial quality and extracted data. Multiple attempts to contact the authors of one study yielded no response. We identified no trials that met the inclusion criteria for the review. We discarded the majority of the references retrieved from our search following screening of the title and abstract. We formally excluded four studies following review of the full-text report. There is insufficient evidence to determine the effectiveness of antibiotics for preventing recurrent sore throat. This finding must be balanced against the known adverse effects and cost of antibiotic therapy, when considering antibiotics for this purpose. There is a need for high quality RCTs that compare the effects of antibiotics versus placebo in adults and children with pre-existing recurrent sore throat on the following outcomes: incidence of sore throat recurrence, adverse effects, days off work and absence from school, and the incidence of complications. Future studies should be conducted and reported according to the CONSORT statement.

Efficacy of flurbiprofen 8.75 mg spray in patients with sore throat due to an upper respiratory tract infection: A randomised controlled trial.

PubMed

de Looze, Ferdinandus; Russo, Marc; Bloch, Mark; Montgomery, Barney; Shephard, Adrian; Smith, Gary; Aspley, Sue

2016-06-01

Viral infections cause most cases of pharyngitis (sore throat); consequently, antibiotics are generally not warranted. However, a treatment targeting pain and inflammation, e.g. a topical non-steroidal anti-inflammatory spray, may be helpful for patients. To evaluate the efficacy and safety of flurbiprofen 8.75 mg spray. This randomised, double-blind, parallel group study was conducted at six community-based clinical research centres in Australia and two in New Zealand. Adults with sore throat due to upper respiratory tract infection (onset ≤ four days) took one dose of flurbiprofen (n = 249) or placebo spray (n = 256); after six hours, they could re-dose every three-six hours as required, for three days (max. five doses/day). The primary endpoint was the area under the change from baseline curve in throat soreness from zero-two hours (AUC0-2h). The change from baseline in other sore throat symptoms also assessed efficacy. The mean AUC0-2h for throat soreness was significantly greater with flurbiprofen spray (-1.82; 95% CI: -1.98 to 1.65) compared with placebo (-1.13; 95% CI: -1.27 to 0.99) (P < 0.0001). Significantly greater reductions from baseline were observed with flurbiprofen spray compared with placebo from the first time-points assessed (five minutes for throat soreness/difficulty swallowing, 20 minutes for sore throat pain intensity and 30 minutes for swollen throat) for up to six hours (P < 0.05 for all). There was no significant difference in adverse events between treatment groups during the three-day study. Flurbiprofen spray provides rapid and long-lasting relief from sore throat symptoms, and is well-tolerated over three days.

Throat hit in users of the electronic cigarette: An exploratory study.

PubMed

Etter, Jean-François

2016-02-01

A cross-sectional survey on the Internet in 2012-2014 was used to study the "throat hit," the specific sensation in the throat felt by users of e-cigarettes. Participants were 1672 current users of e-cigarettes, visitors of Websites dedicated to e-cigarettes and to smoking cessation. It was assessed whether the strength of the throat hit was associated with the characteristics of e-cigarettes and e-liquids, modifications of the devices, patterns of use, reasons for use, satisfaction with e-cigarettes, dependence on e-cigarettes, smoking behavior, and perceived effects on smoking. The strongest throat hit was obtained by using better-quality models and liquids with high nicotine content. Those who reported a "very strong" throat hit used liquids with 17.3 mg/mL nicotine, versus 7.1 mg/mL for those reporting a "very weak" hit (p < .001). The strength of the throat hit was also associated with ratings of dependence on e-cigarettes, and with the perceived efficacy of e-cigarettes to relieve craving for tobacco and to facilitate smoking cessation. All the variables assessing satisfaction with e-cigarettes were associated with a stronger throat hit. From a public health perspective, there is a trade-off between e-cigarette models that provide high levels of nicotine, a strong throat hit, high satisfaction, and more effects on smoking, but may also be addictive, and models than contain less nicotine and are less addictive, but produce a weaker throat hit, are less satisfactory, and are possibly less efficient at helping people quit smoking. This trade-off must be kept in mind when regulating e-cigarettes. (c) 2016 APA, all rights reserved).

Streptococcal throat infections and exacerbation of chronic plaque psoriasis: a prospective study.

PubMed

Gudjonsson, J E; Thorarinsson, A M; Sigurgeirsson, B; Kristinsson, K G; Valdimarsson, H

2003-09-01

Guttate psoriasis has a well-known association with streptococcal throat infections but the effects of these infections in patients with chronic psoriasis remains to be evaluated in a prospective study. To determine whether streptococcal throat infections are more common in and can cause exacerbation in patients with chronic psoriasis. Two hundred and eight patients with chronic plaque psoriasis and 116 unrelated age-matched household controls were followed for 1 year. At recruitment all patients were examined, their disease severity scored and throat swabs taken. Patients and corresponding controls were then re-examined and tested for streptococcal colonization whenever they reported sore throat or exacerbation of their psoriasis during the study period. The psoriasis patients reported sore throat significantly more often than controls (61 of 208 vs. three of 116, P < 0.0001), and beta-haemolytic streptococci of Lancefield groups A, C and G (M protein-positive streptococci) were more often cultured from the patients than the controls (19 of 208 vs. one of 116, P = 0.003). A significant exacerbation of psoriasis (P = 0.004) was observed only if streptococci were isolated and the patients were assessed 4 days or later after the onset of sore throat. No difference was observed between groups A, C or G streptococci in this respect. This study confirms anecdotal and retrospective reports that streptococcal throat infections can cause exacerbation of chronic plaque psoriasis. It is concluded that psoriasis patients should be encouraged to report sore throat to their physician and that early treatment of streptococcal throat infections might be beneficial in psoriasis. A controlled trial for assessing potential benefits of tonsillectomy in patients with severe psoriasis should also be considered.

Recurring Strep Throat: When Is Tonsillectomy Useful?

MedlinePlus

... throat: When is tonsillectomy useful? My 7-year-old daughter has been diagnosed with strep throat four ... of Privacy Practices Notice of Nondiscrimination Manage Cookies Advertising Mayo Clinic is a not-for-profit organization ...

Tonsils and Tonsillectomies (For Parents)

MedlinePlus

... may order a throat culture to check for strep throat. About Tonsillectomies Doctors might recommend surgical removal of ... Kids With No Tonsils More Susceptible to Infections? Strep Throat Preparing Your Child for Surgery Tonsillitis Enlarged Adenoids ...

Strep Throat (For Teens)

MedlinePlus

... First Aid & Safety Doctors & Hospitals Videos Recipes for Kids Kids site Sitio para niños How the Body ... teens. In fact, strep bacteria cause almost a third of all sore throats. Strep throat usually requires ...

Quench Module Insert (QMI) and the Diffusion Module Insert (DMI) Furnace Development

NASA Technical Reports Server (NTRS)

Crouch, Myscha R.; Carswell, William E.; Farmer, Jeff; Rose, Fred; Tidwell, Paul H., II

2000-01-01

The Quench Module Insert (QMI) and the Diffusion Module Insert (DMI) are microgravity furnaces under development at Marshall Space Flight Center. The furnaces are being developed for the first Materials Science Research Rack (MSRR-1) of the Materials Science Research Facility (MSRF), one of the first International Space Station (ISS) scientific payloads. QMI is a Bridgman furnace with quench capability for studying interface behavior during directional solidification of metallic and alloy materials. DMI will be a Bridgman-Stockbarger furnace to study diffusion processes in semiconductors. The design for each insert, both QMI and DMI, is driven by specific science, operations and safety requirements, as well as by constraints arising from resource limitations, such as volume, mass and power. Preliminary QMI analysis and testing indicates that the design meets these requirements.

Aeroelastic Flutter Behavior of Cantilever within a Nozzle-Diffuser Geometry

NASA Astrophysics Data System (ADS)

Tosi, Luis Phillipe; Colonius, Tim; Sherrit, Stewart; Lee, Hyeong Jae

2015-11-01

Aeroelastic flutter arises when the motion of a structure and its surrounding flowing fluid are coupled in a constructive manner, causing large amplitudes of vibration in the immersed solid. A cantilevered beam in axial flow within a nozzle-diffuser geometry exhibits interesting resonance behavior that presents good prospects for internal flow energy harvesting. Different modes can be excited as a function of throat velocity, nozzle geometry, fluid and cantilever material parameters. This work explores the relationship between the aeroelastic flutter instability boundaries and relevant non-dimensional parameters via experiments. Results suggest that for a linear expansion diffuser geometry, a non-dimensional stiffness, non-dimensional mass, and non-dimensional throat size are the critical parameters in mapping the instability. This map can serve as a guide to future work concerning possible electrical output and failure prediction in energy harvesters.

The role of colour in signalling and male choice in the agamid lizard Ctenophorus ornatus.

PubMed Central

LeBas, N R; Marshall, N J

2000-01-01

Bright coloration and complex visual displays are frequent and well described in many lizard families. Reflectance spectrometry which extends into the ultraviolet (UV) allows measurement of such coloration independent of our visual system. We examined the role of colour in signalling and mate choice in the agamid lizard Ctenophorus ornatus. We found that throat reflectance strongly contrasted against the granite background of the lizards' habitat. The throat may act as a signal via the head-bobbing and push-up displays of C. ornatus. Dorsal coloration provided camouflage against the granite background, particularly in females. C. ornatus was sexually dichromatic for all traits examined including throat UV reflectance which is beyond human visual perception. Female throats were highly variable in spectral reflectance and males preferred females with higher throat chroma between 370 and 400 nm. However, female throat UV chroma is strongly correlated to both throat brightness and chest UV chroma and males may choose females on a combination of these colour variables. There was no evidence that female throat or chest coloration was an indicator of female quality. However, female brightness significantly predicted a female's laying date and, thus, may signal receptivity. One function of visual display in this species appears to be intersexual signalling, resulting in male choice of females. PMID:10737400

Insert Design and Manufacturing for Foam-Core Composite Sandwich Structures

NASA Astrophysics Data System (ADS)

Lares, Alan

Sandwich structures have been used in the aerospace industry for many years. The high strength to weight ratios that are possible with sandwich constructions makes them desirable for airframe applications. While sandwich structures are effective at handling distributed loads such as aerodynamic forces, they are prone to damage from concentrated loads at joints or due to impact. This is due to the relatively thin face-sheets and soft core materials typically found in sandwich structures. Carleton University's Uninhabited Aerial Vehicle (UAV) Project Team has designed and manufactured a UAV (GeoSury II Prototype) which features an all composite sandwich structure fuselage structure. The purpose of the aircraft is to conduct geomagnetic surveys. The GeoSury II Prototype serves as the test bed for many areas of research in advancing UAV technologies. Those areas of research include: low cost composite materials manufacturing, geomagnetic data acquisition, obstacle detection, autonomous operations and magnetic signature control. In this thesis work a methodology for designing and manufacturing inserts for foam-core sandwich structures was developed. The results of this research work enables a designer wishing to design a foam-core sandwich airframe structure, a means of quickly manufacturing optimized inserts for the safe introduction of discrete loads into the airframe. The previous GeoSury II Prototype insert designs (v.1 & v.2) were performance tested to establish a benchmark with which to compare future insert designs. Several designs and materials were considered for the new v.3 inserts. A plug and sleeve design was selected, due to its ability to effectively transfer the required loads to the sandwich structure. The insert material was chosen to be epoxy, reinforced with chopped carbon fibre. This material was chosen for its combination of strength, low mass and also compatibility with the face-sheet material. The v.3 insert assembly is 60% lighter than the previous insert designs. A casting process for manufacturing the v.3 inserts was developed. The developed casting process, when producing more than 13 inserts, becomes more economical than machining. An exploratory study was conducted looking at the effects of dynamic loading on the v.3 insert performance. The results of this study highlighted areas for improving dynamic testing of foam-core sandwich structure inserts. Correlations were developed relating design variables such as face-sheet thickness and insert diameter to a failure load for different load cases. This was done through simulations using Computer Aided Engineering (CAE) software, and experimental testing. The resulting correlations were integrated into a computer program which outputs the required insert dimensions given a set of design parameters, and load values.

When a Sore Throat Is a More Serious Infection

MedlinePlus

... often called Hand, Foot, and Mouth disease). Infectious mononucleosis can produce a sore throat, often with marked ... most young children who are infected with the mononucleosis virus have few or no symptoms. Strep throat ...

Streptococcal screen

MedlinePlus

Rapid strep test ... recommend this test if you have signs of strep throat, which include: Fever Sore throat Tender and ... A negative strep screen most often means group A streptococcus is not present. It is unlikely that you have strep throat. ...

Difference between a Sore Throat, Strep, and Tonsillitis

MedlinePlus

... extreme trouble swallowing (causing her to drool). Throat culture This may indicate a more serious infection. The ... examine your child and may perform a throat culture to determine the nature of the infection. To ...

Strep Test: Throat Culture (For Parents)

MedlinePlus

... Fitness Diseases & Conditions Infections Drugs & Alcohol School & Jobs Sports Expert Answers (Q&A) Staying Safe Videos for Educators Search English Español Strep Test: Throat Culture KidsHealth / For Parents / Strep Test: Throat Culture What's ...

A five-year experience with throat cultures.

PubMed

Shank, J C; Powell, T A

1984-06-01

This study addresses the usefulness of the throat culture in a family practice residency setting and explores the following questions: (1) Do faculty physicians clinically identify streptococcal pharyngitis better than residents? (2) With time, will residents and faculty physicians improve in their diagnostic accuracy? (3) Should the throat culture be used always, selectively, or never? A total of 3,982 throat cultures were obtained over a five-year study period with 16 percent positive for beta-hemolytic streptococci. The results were compared with the physician's clinical diagnosis of either "nonstreptococcal" (category A) or "streptococcal" (category B). Within category A, 363 of 3,023 patients had positive cultures (12 percent clinical diagnostic error rate). Within category B, 665 of 959 patients had negative cultures (69 percent clinical diagnostic error rate). Faculty were significantly better than residents in diagnosing streptococcal pharyngitis, but not in diagnosing nonstreptococcal sore throats. Neither faculty nor residents improved their diagnostic accuracy over time. Regarding age-specific recommendations, the findings support utilizing a throat culture in all children aged 2 to 15 years with sore throat, but in adults only when the physician suspects streptococcal pharyngitis.

Polygyny, mate-guarding, and posthumous fertilization as alternative male mating strategies.

PubMed

Zamudio, K R; Sinervo, B

2000-12-19

Alternative male mating strategies within populations are thought to be evolutionarily stable because different behaviors allow each male type to successfully gain access to females. Although alternative male strategies are widespread among animals, quantitative evidence for the success of discrete male strategies is available for only a few systems. We use nuclear microsatellites to estimate the paternity rates of three male lizard strategies previously modeled as a rock-paper-scissors game. Each strategy has strengths that allow it to outcompete one morph, and weaknesses that leave it vulnerable to the strategy of another. Blue-throated males mate-guard their females and avoid cuckoldry by yellow-throated "sneaker" males, but mate-guarding is ineffective against aggressive orange-throated neighbors. The ultradominant orange-throated males are highly polygynous and maintain large territories; they overpower blue-throated neighbors and cosire offspring with their females, but are often cuckolded by yellow-throated males. Finally, yellow-throated sneaker males sire offspring via secretive copulations and often share paternity of offspring within a female's clutch. Sneaker males sire more offspring posthumously, indicating that sperm competition may be an important component of their strategy.

First Materials Science Research Rack Capabilities and Design Features

NASA Technical Reports Server (NTRS)

Schaefer, D.; King, R.; Cobb, S.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The first Materials Science Research Rack (MSRR-1) will accommodate dual Experiment Modules (EM's) and provide simultaneous on-orbit processing operations capability. The first international Materials Science Experiment Module for the MSRR-1 is an international cooperative research activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center. (ESTEC). This International Standard Payload Rack (ISPR) will contain the Materials Science Laboratory (MSL) developed by ESA as an Experiment Module. The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts. Module Inserts currently planned are a Quench Module Insert, Low Gradient Furnace, Solidification with Quench Furnace, and Diffusion Module Insert. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Department (SPD). It includes capabilities for vapor transport processes and liquid metal sintering. This Experiment Module will be replaced on-orbit with other NASA Materials Science EMs.

Safety and efficacy of a traditional herbal medicine (Throat Coat) in symptomatic temporary relief of pain in patients with acute pharyngitis: a multicenter, prospective, randomized, double-blinded, placebo-controlled study.

PubMed

Brinckmann, Josef; Sigwart, Herbert; van Houten Taylor, Leslie

2003-04-01

To investigate the safety and efficacy of Throat Coat) (Traditional Medicinals,) Sebastopol, CA), a traditional demulcent herbal tea, in comparison with a placebo tea in the symptomatic treatment of acute pharyngitis. Multicenter, prospective, randomized, double-blinded, placebo-controlled, two-armed, parallel-group clinical trial. Three primary care clinics in Duluth, MN, Madison, WI, and Middleton, WI. Patients of both genders (>or=18 years of age) with clinical diagnoses of acute pharyngitis. Patients (n = 60) were randomly assigned to receive 5-8 oz of Throat Coat (n = 30) or a placebo (n = 30), four to six times daily. The study period was 2 to 7 days with a window for the follow-up visit of 2-10 days accounting for the variable duration of sore throat symptoms. Primary efficacy parameter: sum of pain intensity differences (SPID) for pain in throat on swallowing, calculated as the area under the curve (AUC) of pain intensity difference scores (assessed at 1 minute, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 30 minutes after treatment). Secondary efficacy parameter: total pain relief (TOTPAR), calculated as the AUC from time 0 (baseline) to 30 minutes of pain relief (assessed at 1 minute, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 30 minutes). Compared to placebo, intensity of throat pain when swallowing was significantly reduced by Throat Coat in intention to treat and valid for efficacy analysis (VEA). Significant differences in change from baseline pain were observed at 5 min (p = 0.007), 10 min (p = 0.005), 15 minutes (p = 0.01), 20 minutes (p = 0.05), and 30 minutes (p = 0.04) after completion of the first dose (VEA analysis). There was a statistically significant improvement of SPID in the Throat Coat-treated group: Least square means +/- standard error of the means (SEM) of SPID were -16.5 +/- 13.9 in the placebo group and -43.8 +/- 11.9 in the Throat Coat-treated group (p = 0.012). TOTPAR was also significantly higher in the Throat Coat-treated group: Least square means +/- SEM of TOTPAR were 32.4 +/- 12.8 in the placebo group and 53.6 +/- 10.9 in the Throat Coat-treated group (p = 0.031). This study shows that Throat Coat is significantly superior to placebo and provided a rapid, temporary relief of sore throat pain in patients with pharyngitis.

Dual-fuel, dual-throat engine preliminary analysis

NASA Technical Reports Server (NTRS)

Obrien, C. J.

1979-01-01

A propulsion system analysis of the dual fuel, dual throat engine for launch vehicle applications was conducted. Basic dual throat engine characterization data were obtained to allow vehicle optimization studies to be conducted. A preliminary baseline engine system was defined.

Strep throat

MedlinePlus

... repeated cases of strep still occur in a family, you might check to see if someone is a strep carrier. Carriers have strep in their throats, but the bacteria do not make them sick. Sometimes, treating them can prevent others from getting strep throat.

Scoop on Strep Throat (For Kids)

MedlinePlus

... First Aid & Safety Doctors & Hospitals Videos Recipes for Kids Kids site Sitio para niños How the Body Works ... Educators Search English Español Strep Throat KidsHealth / For Kids / Strep Throat What's in this article? What Is ...

Use of antibiotics in the management of sore throat.

PubMed

Wilkinson, Ann Elizabeth

2015-03-01

As the number of antibiotic-resistant strains of bacteria rises, it becomes crucial that decisions about the use of antibiotics are based on sound evidence. This article offers a case study to explore the treatment of patients with sore throat who present to minor injury settings. It describes some 'red flag' presentations, discusses the pros and cons of prescribing antibiotics for sore throat, and describes some scoring systems that can help differentiate between bacterial and viral throat infections.

Comparison of Effectiveness of Betamethasone gel Applied to the Tracheal Tube and IV Dexamethasone on Postoperative Sore Throat: A Randomized Controlled Trial.

PubMed

Tabari, Masumeh; Soltani, Ghasem; Zirak, Nahid; Alipour, Moammad; Khazaeni, Kamran

2013-09-01

Postoperative sore throat is a common complaint in patients with endotracheal intubation and has potentially dangerous complications. This randomized controlled trial study investigated the incidence of postoperative sore throat after general anesthesia when betamethasone gel is applied to a tracheal tube compared with when IV dexamethasone is prescribed. Two hundred and twenty five American Society of Anesthesiologist (ASA)-class I and II patients undergoing elective abdominal surgery with tracheal intubation were randomly divided into three groups: betamethasone gel, intravenous (IV) dexamethasone, and control groups. In the post-anesthesia care unit, a blinded anesthesiologist interviewed all patients regarding postoperative sore throat at 1,6, and 24 hours after surgery. The incidence of sore throat was significantly lower in the betamethasone gel group compared with the IV dexamethasone and control groups, 1, 6, and 24 hours after surgery. In the first day after surgery 10.7% of the betamethasone group had sore throat whereas 26.7% of the IV dexamethasone group and 30.7% of the control group had sore throat. Bucking before extubation was observed in 14(18.4%), 8(10.4%), and 9(12.2%) patients, in the IV dexamethasone, betamethasone gel, and control group, respectively. We concluded that wide spread application of betamethasone gel over tracheal tubes effectively mitigates postoperative sore throat, compared with IV dexamethasone application.

Improvements in throat function and qualities of sore throat from locally applied flurbiprofen 8.75 mg in spray or lozenge format: findings from a randomized trial of patients with upper respiratory tract infection in the Russian Federation.

PubMed

Burova, Natalia; Bychkova, Valeria; Shephard, Adrian

2018-01-01

To assess the speed of relief provided by flurbiprofen 8.75 mg spray and lozenge and their effect on many of the different qualities and characteristics of throat pain and discomfort, and the many articulations of the broad term "sore throat" (ST). Four hundred and forty adults with recent-onset, moderate-to-severe ST due to upper respiratory tract infection (URTI) were randomized to a single dose of either flurbiprofen 8.75 mg spray (n=218) or flurbiprofen 8.75 mg lozenge (n=222). Throat swabs for bacterial culture were taken at baseline. ST relief was assessed at 1 minute, 1 and 2 hours post-dose using the Sore Throat Relief Rating Scale. The change from baseline at 1 and 2 hours post-dose in difficulty swallowing and swollen throat was assessed using the difficulty swallowing scale and the swollen throat scale, respectively. Patients' experience of URTI symptoms was assessed using a URTI questionnaire at baseline and 2 hours post-dose. The change in Qualities of Sore Throat Index, a 10-item index of qualities of ST, from baseline at 2 hours post-dose was also measured. ST relief was evident in the spray and the lozenge treatment groups at 1 minute, 1 and 2 hours post-dose ( P >0.05). In both groups, scores for difficulty swallowing and swollen throat significantly improved at 1 and 2 hours post-dose compared with baseline. At 2 hours post-dose, the number of patients experiencing URTI symptoms that can be attributed to or associated with ST decreased relative to baseline. The mean change from baseline to 2 hours post-dose for each individual score on the Qualities of Sore Throat Index showed significant improvements for flurbiprofen spray and lozenge (all P <0.0001). Non-inferiority was established, and flurbiprofen spray and lozenge provided effective relief from ST pain and many of the other commonly reported qualities of ST.

Orbital transfer vehicle 3000 LBF thrust chamber assembly hot fire test program

NASA Technical Reports Server (NTRS)

Schneider, Judy; Hayden, Warren R.

1988-01-01

The Aerojet Orbital Transfer Vehicle (OTV) Thrust Chamber Assembly (TCA) concept consists of a hydrogen cooled chamber, and annular injector, and an oxygen cooled centerbody. The hot fire testing of a heat sink version of the chamber with only the throat section using hydrogen cooling is documented. Hydraulic performance of the injector and cooled throat were verified by water flow testing prior to TCA assembly. The cooled throat was proof tested to 3000 psia to verify the integrity of the codeposited EF nickel-cobalt closeout. The first set of hot fire tests were conducted with a heat sink throat to obtain heat flux information. After demonstration of acceptable heat fluxes, the heat sink throat was replaced with the LH2 cooled throat section. Fourteen tests were conducted with a heat sink chamber and throat at chamber pressures of 85 to 359 psia. The injector face was modified at this time to add more face coolant flow. Ten tests were then conducted at chamber pressures of 197 to 620 psia. Actual heat fluxes at the higher chamber pressure range were 23 percent higher than the average of 10 Btu/in 2 predicted.

Internal Performance of a Fixed-Shroud Nonaxisymmetric Nozzle Equipped with an Aft-Hood Exhaust Deflector

NASA Technical Reports Server (NTRS)

Asbury, Scott C.

1997-01-01

An investigation was conducted in the model preparation area of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a fixed-shroud nonaxisymmetric nozzle equipped with an aft-hood exhaust deflector. Model geometric parameters investigated included nozzle power setting, aft-hood deflector angle, throat area control with the aft-hood deflector deployed, and yaw vector angle. Results indicate that cruise configurations produced peak performance in the range consistent with previous investigations of nonaxisymmetric convergent-divergent nozzles. The aft-hood deflector produced resultant pitch vector angles that were always less than the geometric aft-hood deflector angle when the nozzle throat was positioned upstream of the deflector exit. Significant losses in resultant thrust ratio occurred when the aft-hood deflector was deployed with an upstream throat location. At each aft-hood deflector angle, repositioning the throat to the deflector exit improved pitch vectoring performance and, in some cases, substantially improved resultant thrust ratio performance. Transferring the throat to the deflector exit allowed the flow to be turned upstream of the throat at subsonic Mach numbers, thereby eliminating losses associated with turning supersonic flow. Internal throat panel deflections were largely unsuccessful in generating yaw vectoring.

Polygyny, mate-guarding, and posthumous fertilization as alternative male mating strategies

PubMed Central

Zamudio, Kelly R.; Sinervo, Barry

2000-01-01

Alternative male mating strategies within populations are thought to be evolutionarily stable because different behaviors allow each male type to successfully gain access to females. Although alternative male strategies are widespread among animals, quantitative evidence for the success of discrete male strategies is available for only a few systems. We use nuclear microsatellites to estimate the paternity rates of three male lizard strategies previously modeled as a rock-paper-scissors game. Each strategy has strengths that allow it to outcompete one morph, and weaknesses that leave it vulnerable to the strategy of another. Blue-throated males mate-guard their females and avoid cuckoldry by yellow-throated “sneaker” males, but mate-guarding is ineffective against aggressive orange-throated neighbors. The ultradominant orange-throated males are highly polygynous and maintain large territories; they overpower blue-throated neighbors and cosire offspring with their females, but are often cuckolded by yellow-throated males. Finally, yellow-throated sneaker males sire offspring via secretive copulations and often share paternity of offspring within a female's clutch. Sneaker males sire more offspring posthumously, indicating that sperm competition may be an important component of their strategy. PMID:11106369

Diagnosis of Group A Streptococcal Infections Directly From Throat Gargle.

DTIC Science & Technology

1981-06-01

Streptococcal Infection Strep Throat Latex agglutination 20. ARVAT(Continue an revere side it neessar and identify by block num~ber) The diagnosis of... THROAT GARGLE ,-I E. A. EDWARDS, 1. A. PH1WPS & W. C. SUITER REPORT NO. 81-20 DTIC IELECTE VAL A11OCT I lSlt P.O. BOX 8022 SAN DIEGO, CALIFORNIA 92138...AVAL MICAL RESEARCH AND DEVELOPMENT COMMAND BE0hESDA, MARYLAND £ 81 9 30 069 (. DIAGNOSIS OF QROUP A STREPTOCOCCAL INFECTIONS ~1IRECTLY FROM ThROAT

Characterization and Persistence of Staphylococcus aureus Strains Isolated from the Anterior Nares and Throats of Healthy Carriers in a Mexican Community▿

PubMed Central

Hamdan-Partida, Aída; Sainz-Espuñes, Teresita; Bustos-Martínez, Jaime

2010-01-01

Healthy carriers of Staphylococcus aureus strains have an important role in the dissemination of this bacterium. To investigate the presence of S. aureus in the throat and anterior nares, samples from 1,243 healthy volunteers in a Mexican community were examined. The percentage of healthy carriers was 59.8%. Results showed that colonization of the throat occurred more frequently than that of the nares (46.5% versus 37.1%, P < 0.0001). Of the S. aureus carriers, 22.2% were exclusive nasal carriers and 38% were exclusive throat carriers. A total of 1,039 strains were isolated; 12.6% were shown to be methicillin-resistant S. aureus (MRSA). Of MRSA strains, 32.1% were isolated from exclusive throat carriers. Most of the strains isolated from the anterior nares and throat of the same carriers were the same or related; however, some were different. Pulsed-field gel electrophoresis (PFGE) pattern analysis of the MRSA strains isolated from the exclusive nasal carriers or exclusive throat carriers showed that they belong to different clusters. A 6-year prospective study was performed to investigate the persistence of S. aureus in the throat. Results showed that 13% of subjects were persistent carriers. Most of them were colonized with the same clone of S. aureus throughout the time of the study, and just three had different clones. Antimicrobial susceptibility testing showed that 91.1% of the strains were penicillin resistant. The presence of mecA and nucA genes (in order to confirm methicillin resistance) and of thermostable nuclease of S. aureus was examined. This study showed that some strains of S. aureus regularly colonized the throats of healthy people and could persist for years. PMID:20335416

Sore throat in primary care project: a clinical score to diagnose viral sore throat.

PubMed

Mistik, Selcuk; Gokahmetoglu, Selma; Balci, Elcin; Onuk, Fahri A

2015-06-01

Viral agents cause the majority of sore throats. However, there is not currently a score to diagnose viral sore throat. The aims of this study were (i) to find the rate of bacterial and viral causes, (ii) to show the seasonal variations and (iii) to form a new scoring system to diagnose viral sore throat. A throat culture for group A beta haemolytic streptococci (GABHS) and a nasopharyngeal swab to detect 16 respiratory viruses were obtained from each patient. Over a period of 52 weeks, a total of 624 throat cultures and polymerase chain reaction analyses were performed. Logistic regression analysis was performed to find the clinical score. Viral infection was found in 277 patients (44.3%), and GABHS infection was found in 116 patients (18.5%). An infectious cause was found in 356 patients (57.1%). Rhinovirus was the most commonly detected infectious agent overall (highest in November, 34.5%), and the highest GABHS rate was in November (32.7%). Analysis of data provided a scoring system, called the Mistik Score, to diagnose viral sore throat. The predictive model for positive viral analysis included the following variables: absence of headache, stuffy nose, sneezing, temperature of ≥37.5°C on physical examination, and the absence of tonsillar exudate and/or swelling. The probability of a positive viral analysis for a score of 5 was 82.1%. The Mistik Score may be useful to diagnose viral sore throat. We suggest its use either alone or in combination with the Modified Centor Score. © The Author 2015. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

A Reappraisal of the Minimum Duration of Antibiotic Treatment Before Approval of Return to School for Children With Streptococcal Pharyngitis.

PubMed

Schwartz, Richard H; Kim, Danica; Martin, Michael; Pichichero, Michael E

2015-12-01

To determine whether a single dose of amoxicillin administered to a symptomatic child with confirmed strep throat might allow the child to return to school as little as 12 hours later. We enrolled 111 evaluable children with sore throat plus a positive streptococcal rapid antigen detection test (RADT) as well as a positive result for group A Streptococci (GAS). After throat swab specimens were obtained, all participants received a single dose of amoxicillin (50 mg/kg). Twelve to 23 hours after the first dose of amoxicillin, all participants returned in the morning of day 2 for a second throat swab specimen. At the day 2 visit, a nurse or medical assistant obtained an interval history, tympanic membrane temperature, and a pediatrician or nurse practitioner examined the oropharynx. On the morning of day 2, only 10 of 111 participants continued to have a positive RADT result, confirmed by overnight throat culture. GAS were not detectable on the day 2 throat specimen by RADT and also by culture in 91% of the study participants (confidence interval: 86-96%). Seven of 10 failures had a marked decrease in number of β-hemolytic colonies, which were 3+ to 4+ on the initial overnight culture plate and decreased to 1+ on the follow-up (obtained on day 2) throat culture plate. Two participants continued to have 3+ or 4+ GAS after incubation of the second throat culture specimen. Even in the late afternoon, a full dose of amoxicillin (50 mg/kg) administered after notification of positive RADT results for GAS resulted in nondetection of GAS in 91% of children the next morning. All children treated with amoxicillin for "strep throat" by 5 PM of day 1 may, if afebrile and improved, attend school on day 2.

Electrochemical fluorination of La(2)CuO(4): a mild "chimie douce" route to superconducting oxyfluoride materials.

PubMed

Delville, M H; Barbut, D; Wattiaux, A; Bassat, J M; Ménétrier, M; Labrugère, C; Grenier, J C; Etourneau, J

2009-08-17

The fluorination of La(2)CuO(4) was achieved for the first time under normal conditions of pressure and temperature (1 MPa and 298 K) via electrochemical insertion in organic fluorinated electrolytes and led to lanthanum oxyfluorides of general formula La(2)CuO(4)F(x). Analyses showed that, underneath a very thin layer of LaF(3) (a few atomic layers), fluorine is effectively inserted in the material's structure. The fluorination strongly modifies the lanthanum environment, whereas very little modification is observed on copper, suggesting an insertion in the La(2)O(2) blocks of the structure. In all cases, fluorine insertion breaks the translation symmetry and introduces a long-distance disorder, as shown by electron spin resonance. These results highlight the efficiency of electrochemistry as a new "chimie douce" type fluorination technique for solid-state materials. Performed at room temperature, it additionally does not require any specific experimental care. The choice of the electrolytic medium is crucial with regard to the fluorine insertion rate as well as the material deterioration. Successful application of this technique to the well-known La(2)CuO(4) material provides a basis for further syntheses from other oxides.

21 CFR 874.4420 - Ear, nose, and throat manual surgical instrument.

Code of Federal Regulations, 2010 CFR

2010-04-01

... device includes the esophageal dilator; tracheal bistour (a long, narrow surgical knife); tracheal dilator; tracheal hook; laryngeal injection set; laryngeal knife; laryngeal saw; laryngeal trocar...; wire ear loop; microrule; mirror; mobilizer; ear, nose, and throat punch; ear, nose and throat knife...

Red-throated loons (Gavia stellata) breeding in Alaska, USA, are exposed to PCBs while on their Asian wintering grounds

USGS Publications Warehouse

Schmutz, J.A.; Trust, K.A.; Matz, A.C.

2009-01-01

Red-throated loons (Gavia stellata) breeding in Alaska declined 53% during 1977-1993. We compare concentrations of environmental contaminants in red-throated loons among four nesting areas in Alaska and discuss potential ramifications of exposure on reproductive success and population trends. Eggs from the four areas had similar total polychlorinated biphenyl (PCB) concentrations, but eggs from the Arctic coastal plain had different congener profiles and greater toxic equivalents (TEQs) than eggs from elsewhere. Satellite telemetry data indicate that red-throated loons from the Arctic coastal plain in northern Alaska winter in southeast Asia, while those breeding elsewhere in Alaska winter in North America. Different wintering areas may lead to differential PCB accumulation among red-throated loon populations. For eggs from the Arctic coastal plain, TEQs were great enough to postulate PCB-associated reproductive effects in piscivores. The correlation between migration patterns and PCB profiles suggests that red-throated loons breeding in northern Alaska are exposed to PCBs while on their Asian wintering grounds.

Improved composite material and method for production of improved composite material

NASA Technical Reports Server (NTRS)

Farley, Gary L. (Inventor)

1994-01-01

A laminated composite material with improved interlaminar strength and damage tolerance having short rods distributed evenly throughout the composite material perpendicular to the laminae is introduced. Each rod is shorter than the thickness of the finished laminate, but several times as long as the thickness of each lamina. The laminate is made by inserting short rods in layers of prepreg material, and then stacking and curing prepreg material with rods inserted therethrough.

Survival of adult Red-throated Loons (Gavia stellata) may be linked to marine conditions

USGS Publications Warehouse

Schmutz, Joel A.

2014-01-01

Large variations in the summering population size of Red-throated Loons (Gavia stellata) have occurred in recent decades in Alaska. Little information exists about annual or seasonal survival rates of adult Red-throated Loons. This study used tracking data from satellite transmitters implanted into 33 Red-throated Loons captured on breeding areas in Alaska to estimate annual survival with the sampling effort split between two study periods: 2000–2002 and 2008–2010. Mortality was inferred from transmitted sensor data that indicated body temperature of the Red-throated Loon and voltage of the transmitter's battery. Two definitive mortalities occurred, resulting in an annual survival estimate of 0.920 (SE = 0.054). The fates of two additional Red-throated Loons were ambiguous and, when treated as mortalities, the annual survival estimate was 0.838 (SE = 0.074). All four putative mortalities occurred during the non-breeding season in the early study period. Oceanic conditions, indexed by the Pacific Decadal Oscillation, appeared to differ between the study periods with higher Pacific Decadal Oscillation values associated with the early study period. Given that high values for Pacific Decadal Oscillation were also associated with the large decline of Red-throated Loons observed in Alaska during 1977–1993, this study suggests that survival of adult Red-throated Loons may vary in relation to the state of the marine ecosystem and thus contribute to long-term variation in population trends.

Methods for Using Durable Adhesively Bonded Joints for Sandwich Structures

NASA Technical Reports Server (NTRS)

Smeltzer, Stanley S., III (Inventor); Lundgren, Eric C. (Inventor)

2016-01-01

Systems, methods, and apparatus for increasing durability of adhesively bonded joints in a sandwich structure. Such systems, methods, and apparatus includes an first face sheet and an second face sheet as well as an insert structure, the insert structure having a first insert face sheet, a second insert face sheet, and an insert core material. In addition, sandwich core material is arranged between the first face sheet and the second face sheet. A primary bondline may be coupled to the face sheet(s) and the splice. Further, systems, methods, and apparatus of the present disclosure advantageously reduce the load, provide a redundant path, reduce structural fatigue, and/or increase fatigue life.

Systems, Apparatuses, and Methods for Using Durable Adhesively Bonded Joints for Sandwich Structures

NASA Technical Reports Server (NTRS)

Smeltzer, III, Stanley S. (Inventor); Lundgren, Eric C. (Inventor)

2014-01-01

Systems, methods, and apparatus for increasing durability of adhesively bonded joints in a sandwich structure. Such systems, methods, and apparatus includes an first face sheet and an second face sheet as well as an insert structure, the insert structure having a first insert face sheet, a second insert face sheet, and an insert core material. In addition, sandwich core material is arranged between the first face sheet and the second face sheet. A primary bondline may be coupled to the face sheet(s) and the splice. Further, systems, methods, and apparatus of the present disclosure advantageously reduce the load, provide a redundant path, reduce structural fatigue, and/or increase fatigue life.

Technique for joining metal tubing

NASA Technical Reports Server (NTRS)

Wright, H. W.

1976-01-01

Uniform wall thickness and uninterrupted heat transfer is achieved by using shaped metal insert as wall material for joint. Insert acts as support during brazing, after which excess material is ground away to bring joint to original tubing size.

Improvement of the radiographic method for measurement of effective energy of pulsed X-ray emission from a PF device for different anode's insert materials.

PubMed

Miremad, Seyed Milad; Shirani, Babak

2018-06-01

In this paper, effective energy of pulsed X-Ray emitted from a Mather-type plasma focus device in stored energy of 2.5 kJ with six different anode's insert materials was measured using radiographic method with attenuation filters. Since intensity and energy of X-ray beam were considerably changed with changing the insert material, the method was improved by using different filters simultaneously in all the experiments and selection of the best filter in each experiment according to the appropriate criteria. Effective energy of pulsed X-ray beam was measured 16, 28, 50, 51, 34 and 44 keV when aluminum, copper, zinc, tin, tungsten and lead were used as insert materials, and aluminum, copper, silver, silver, copper and lead were used as filters, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Variable flow gas turbine engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stroem, S.

1986-11-25

This patent describes a variable flow gas turbine engine of the type having a combustor for generating combustion gases and a turbine rotor for receiving and expanding the hot combustion gases, comprising: duct means for defining a channel for directing the flow of combustion gases from the combustor to the rotor; vane means in the channel forming at least one throat; means for varying the effective flow area for combustion gases flowing through the throat and impinging on the rotor. The varying means includes winglet means fixedly mounted in the throat for separating the gases flowing through the throat intomore » first and second streams; and means for injecting high pressure fluid into the throat for varying the flow of combustion gases in one of the streams.« less

Stakeholders' views of recurrent sore throat, tonsillitis and their management: a qualitative interview study for the NAtional Trial of Tonsillectomy IN Adults (NATTINA Part 1).

PubMed

McSweeney, L A; Rousseau, N S; Wilson, J A; Wilkes, S; Haighton, C A

2017-04-01

To determine the impact of recurrent sore throats and tonsillitis in adults and stakeholder views of treatment pathways. Qualitative semistructured interview design reporting novel data from a feasibility study for a UK national trial of tonsillectomy in adults. Nine study sites linked to ear, nose and throat departments in National Health Service hospitals located across the United Kingdom. Fifteen patients, 11 general practitioners and 22 ear, nose and throat staff consented to in-depth interviews, which were analysed using a framework analysis approach. Views of stakeholder groups. Recurrent sore throats were reported to severely impact patients' family, work and social life. Ear, nose and throat staff stated that patients faced increasing barriers to secondary care service access. General practitioners were under pressure to reduce 'limited clinical value' surgical procedures. The findings from this study suggest that there is a disconnect between the attitudes of the stakeholders and the reality of recurrent sore throat, tonsillectomy procedures and service provision. More evidence for the role of tonsillectomy is needed from randomised controlled trials to determine whether it should continue to be ranked as a procedure of limited clinical effectiveness. © 2016 John Wiley & Sons Ltd.

The effectiveness of the McIsaac clinical decision rule in the management of sore throat: an evaluation from a pediatrics ward.

PubMed

Thillaivanam, Saravanapriya; Amin, Arwa M; Gopalakrishnan, Sheila; Ibrahim, Baharudin

2016-10-01

Sore throats may be due to either viral or group A beta hemolytic streptococcus (GABHS) infections; but diagnosis of the etiology of a sore throat is difficult, often leading to unnecessary antibiotic prescriptions and consequent increases in bacterial resistance. Scoring symptoms using the McIsaac clinical decision rule can help physicians to diagnose and manage streptococcal infections leading to sore throat and have been recommended by the Ministry of Health, Malaysia. In this paper, we offer the first assessment of the effectiveness of the McIsaac rule in a clinical setting in Malaysia. This study is a retrospective review of 116 pediatric patients presenting with sore throat. Group A comprised patients before the implementation of the McIsaac rule and Group B comprised patients after the implementation. Unnecessary throat swab cultures were reduced by 40% (P = 0.003). Redundant antibiotic prescriptions were reduced by 26.5% (P = 0.003) and the overall use of antibiotics was reduced by 22.1% (P = 0.003). The pediatricians' compliance rate to McIsaac rule criteria was 45% before implementation of the McIsaac rule, but improved to 67.9% (P = 0.0005) after implementation. The McIsaac rule is an effective tool for the management of sore throat in children in Malaysia.

Improvements in throat function and qualities of sore throat from locally applied flurbiprofen 8.75 mg in spray or lozenge format: findings from a randomized trial of patients with upper respiratory tract infection in the Russian Federation

PubMed Central

Burova, Natalia; Bychkova, Valeria; Shephard, Adrian

2018-01-01

Objective To assess the speed of relief provided by flurbiprofen 8.75 mg spray and lozenge and their effect on many of the different qualities and characteristics of throat pain and discomfort, and the many articulations of the broad term “sore throat” (ST). Patients and methods Four hundred and forty adults with recent-onset, moderate-to-severe ST due to upper respiratory tract infection (URTI) were randomized to a single dose of either flurbiprofen 8.75 mg spray (n=218) or flurbiprofen 8.75 mg lozenge (n=222). Throat swabs for bacterial culture were taken at baseline. ST relief was assessed at 1 minute, 1 and 2 hours post-dose using the Sore Throat Relief Rating Scale. The change from baseline at 1 and 2 hours post-dose in difficulty swallowing and swollen throat was assessed using the difficulty swallowing scale and the swollen throat scale, respectively. Patients’ experience of URTI symptoms was assessed using a URTI questionnaire at baseline and 2 hours post-dose. The change in Qualities of Sore Throat Index, a 10-item index of qualities of ST, from baseline at 2 hours post-dose was also measured. Results ST relief was evident in the spray and the lozenge treatment groups at 1 minute, 1 and 2 hours post-dose (P>0.05). In both groups, scores for difficulty swallowing and swollen throat significantly improved at 1 and 2 hours post-dose compared with baseline. At 2 hours post-dose, the number of patients experiencing URTI symptoms that can be attributed to or associated with ST decreased relative to baseline. The mean change from baseline to 2 hours post-dose for each individual score on the Qualities of Sore Throat Index showed significant improvements for flurbiprofen spray and lozenge (all P<0.0001). Conclusion Non-inferiority was established, and flurbiprofen spray and lozenge provided effective relief from ST pain and many of the other commonly reported qualities of ST.

Tonsillectomy Versus Watchful Waiting for Recurrent Throat Infection: A Systematic Review

PubMed Central

Morad, Anna; Sathe, Nila A.; Francis, David O.; McPheeters, Melissa L.

2017-01-01

CONTEXT: The effectiveness of tonsillectomy or adenotonsillectomy (“tonsillectomy”) for recurrent throat infection compared with watchful waiting is uncertain. OBJECTIVE: To compare sleep, cognitive, behavioral, and health outcomes of tonsillectomy versus watchful waiting in children with recurrent throat infections. DATA SOURCES: MEDLINE, Embase, and the Cochrane Library. STUDY SELECTION: Two investigators independently screened studies against predetermined criteria. DATA EXTRACTION: One investigator extracted data with review by a second. Investigators independently assessed risk of bias and strength of evidence (SOE) and confidence in the estimate of effects. RESULTS: Seven studies including children with ≥3 infections in the previous 1 to 3 years addressed this question. In studies reporting baseline data, number of infections/sore throats decreased from baseline in both groups, with greater decreases in sore throat days, clinician contacts, diagnosed group A streptococcal infections, and school absences in tonsillectomized children in the short term (<12 months). Quality of life was not markedly different between groups at any time point. LIMITATIONS: Few studies fully categorized infection/sore throat severity; attrition was high. CONCLUSIONS: Throat infections, utilization, and school absences improved in the first postsurgical year in tonsillectomized children versus children not receiving surgery. Benefits did not persist over time; longer-term outcomes are limited. SOE is moderate for reduction in short-term throat infections and insufficient for longer-term reduction. SOE is low for no difference in longer-term streptococcal infection reduction. SOE is low for utilization and missed school reduction in the short term, low for no difference in longer-term missed school, and low for no differences in quality of life. PMID:28096515

Tonsillectomy Versus Watchful Waiting for Recurrent Throat Infection: A Systematic Review.

PubMed

Morad, Anna; Sathe, Nila A; Francis, David O; McPheeters, Melissa L; Chinnadurai, Sivakumar

2017-02-01

The effectiveness of tonsillectomy or adenotonsillectomy ("tonsillectomy") for recurrent throat infection compared with watchful waiting is uncertain. To compare sleep, cognitive, behavioral, and health outcomes of tonsillectomy versus watchful waiting in children with recurrent throat infections. MEDLINE, Embase, and the Cochrane Library. Two investigators independently screened studies against predetermined criteria. One investigator extracted data with review by a second. Investigators independently assessed risk of bias and strength of evidence (SOE) and confidence in the estimate of effects. Seven studies including children with ≥3 infections in the previous 1 to 3 years addressed this question. In studies reporting baseline data, number of infections/sore throats decreased from baseline in both groups, with greater decreases in sore throat days, clinician contacts, diagnosed group A streptococcal infections, and school absences in tonsillectomized children in the short term (<12 months). Quality of life was not markedly different between groups at any time point. Few studies fully categorized infection/sore throat severity; attrition was high. Throat infections, utilization, and school absences improved in the first postsurgical year in tonsillectomized children versus children not receiving surgery. Benefits did not persist over time; longer-term outcomes are limited. SOE is moderate for reduction in short-term throat infections and insufficient for longer-term reduction. SOE is low for no difference in longer-term streptococcal infection reduction. SOE is low for utilization and missed school reduction in the short term, low for no difference in longer-term missed school, and low for no differences in quality of life. Copyright © 2017 by the American Academy of Pediatrics.

Effect of porous material heating on the drag force of a cylinder with gas-permeable porous inserts in a supersonic flow

NASA Astrophysics Data System (ADS)

Mironov, S. G.; Poplavskaya, T. V.; Kirilovskiy, S. V.

2017-10-01

The paper presents the results of an experimental investigation of supersonic flow around a solid cylinder with a gas-permeable porous insert on its front end and of supersonic flow around a hollow cylinder with internal porous inserts in the presence of heating of the porous material. The experiments were performed in a supersonic wind tunnel with Mach number 4.85 and 7 with porous inserts of cellular-porous nickel. The results of measurements on the filtration stand of the air filtration rate through the cellular-porous nickel when it is heated are also shown. For a number of experiments, numerical modeling based on the skeletal model of a cellular-porous material was carried out.

21 CFR 874.4250 - Ear, nose, and throat electric or pneumatic surgical drill.

Code of Federal Regulations, 2010 CFR

2010-04-01

... surgical drill. 874.4250 Section 874.4250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH....4250 Ear, nose, and throat electric or pneumatic surgical drill. (a) Identification. An ear, nose, and throat electric or pneumatic surgical drill is a rotating drilling device, including the handpiece, that...

21 CFR 874.4500 - Ear, nose, and throat microsurgical carbon dioxide laser.

Code of Federal Regulations, 2011 CFR

2011-04-01

... laser. 874.4500 Section 874.4500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND..., nose, and throat microsurgical carbon dioxide laser. (a) Identification. An ear, nose, and throat microsurgical carbon dioxide laser is a device intended for the surgical excision of tissue from the ear, nose...

21 CFR 874.4500 - Ear, nose, and throat microsurgical carbon dioxide laser.

Code of Federal Regulations, 2010 CFR

2010-04-01

... laser. 874.4500 Section 874.4500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND..., nose, and throat microsurgical carbon dioxide laser. (a) Identification. An ear, nose, and throat microsurgical carbon dioxide laser is a device intended for the surgical excision of tissue from the ear, nose...

21 CFR 874.4500 - Ear, nose, and throat microsurgical carbon dioxide laser.

Code of Federal Regulations, 2013 CFR

2013-04-01

... laser. 874.4500 Section 874.4500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND..., nose, and throat microsurgical carbon dioxide laser. (a) Identification. An ear, nose, and throat microsurgical carbon dioxide laser is a device intended for the surgical excision of tissue from the ear, nose...

21 CFR 874.4500 - Ear, nose, and throat microsurgical carbon dioxide laser.

Code of Federal Regulations, 2012 CFR

2012-04-01

... laser. 874.4500 Section 874.4500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND..., nose, and throat microsurgical carbon dioxide laser. (a) Identification. An ear, nose, and throat microsurgical carbon dioxide laser is a device intended for the surgical excision of tissue from the ear, nose...

21 CFR 874.4500 - Ear, nose, and throat microsurgical carbon dioxide laser.

Code of Federal Regulations, 2014 CFR

2014-04-01

... laser. 874.4500 Section 874.4500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND..., nose, and throat microsurgical carbon dioxide laser. (a) Identification. An ear, nose, and throat microsurgical carbon dioxide laser is a device intended for the surgical excision of tissue from the ear, nose...

21 CFR 874.5220 - Ear, nose, and throat drug administration device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ear, nose, and throat drug administration device. 874.5220 Section 874.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5220 Ear, nose...

21 CFR 874.5220 - Ear, nose, and throat drug administration device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ear, nose, and throat drug administration device. 874.5220 Section 874.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5220 Ear, nose...

21 CFR 874.5220 - Ear, nose, and throat drug administration device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ear, nose, and throat drug administration device. 874.5220 Section 874.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5220 Ear, nose...

21 CFR 874.5300 - Ear, nose, and throat examination and treatment unit.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ear, nose, and throat examination and treatment unit. 874.5300 Section 874.5300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5300...

21 CFR 874.5220 - Ear, nose, and throat drug administration device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ear, nose, and throat drug administration device. 874.5220 Section 874.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5220 Ear, nose...

21 CFR 874.5300 - Ear, nose, and throat examination and treatment unit.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ear, nose, and throat examination and treatment unit. 874.5300 Section 874.5300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5300...

21 CFR 874.5300 - Ear, nose, and throat examination and treatment unit.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ear, nose, and throat examination and treatment unit. 874.5300 Section 874.5300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5300...

21 CFR 874.5220 - Ear, nose, and throat drug administration device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ear, nose, and throat drug administration device. 874.5220 Section 874.5220 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5220 Ear, nose...

Brown-headed Cowbird parasitism of the Black-throated Sparrow in central Arizona

USGS Publications Warehouse

Johnson, M.J.; van Riper, Charles

2004-01-01

From 1994-1996 we investigated effects of Brown-headed Cowbird (Molothrus ater) parasitism on Black-throated Sparrow (Amphispiza bilineata) nesting success in the Verde Valley of central Arizona. Of 56 Black-throated Sparrow nests, 52% were parasitized. Black-throated Sparrows appear to respond to natural parasitism by accepting the cowbird egg, deserting the nest, or burying the cowbird egg. Removal and damage of host eggs by female cowbirds effectively reduced clutch size from an average of 3.4 to 1.9 eggs. Because of this reduced clutch size, Black-throated Sparrow reproductive success was significantly lower in parasitized nests (0.2 young fledged/ nest) as compared to nonparasitized nests (1.6 young fledged/nest). When comparing cowbird parasitism between two habitat types, we found significantly higher parasitism frequencies in crucifixion-thorn (Canotia holacantha) versus creosote-bush (Larrea divaricata) habitat. We argue that this difference in parasitism is due to the greater number of tall perches (e.g., shrubs >4 m) available in crucifixion-thorn habitat, providing vantage points for female cowbirds to better find Black-throated Sparrow nests.

Ultrasonic airborne insertion loss measurements at normal incidence (L).

PubMed

Farley, Jayrin; Anderson, Brian E

2010-12-01

Transmission loss and insertion loss measurements of building materials at audible frequencies are commonly made using plane wave tubes or as a panel between reverberant rooms. These measurements provide information for noise isolation control in architectural acoustics and in product development. Airborne ultrasonic sound transmission through common building materials has not been fully explored. Technologies and products that utilize ultrasonic frequencies are becoming increasingly more common, hence the need to conduct such measurements. This letter presents preliminary measurements of the ultrasonic insertion loss levels for common building materials over a frequency range of 28-90 kHz using continuous-wave excitation.

Dual throat engine design for a SSTO launch vehicle

NASA Technical Reports Server (NTRS)

Obrien, C. J.; Salmon, J. W.

1980-01-01

A propulsion system analysis of a dual fuel, dual throat engine for launch vehicle application was conducted. Basic dual throat engine characterization data are presented to allow vehicle optimization studies to be conducted. A preliminary baseline engine system was defined. Dual throat engine performance, envelope, and weight parametric data were generated over the parametric range of thrust from 890 to 8896 KN (200K to 2M lb-force), chamber pressure from 6.89 million to 34.5 million N/sq m (1000 to 5000 psia) thrust ratio from 1.2 to 5, and a range of mixture ratios for the two tripropellant combinations: LO2/RP-1 + LH2 and LO2/LCH4 + LH2. The results of the study indicate that the dual fuel dual throat engine is a viable single stage to orbit candidate.

Pressure distribution in a converging-diverging nozzle during two-phase choked flow of subcooled nitrogen

NASA Technical Reports Server (NTRS)

Simoneau, R. J.

1975-01-01

Choked flow rates and axial pressure distributions were measured for subcooled nitrogen in a converging-diverging nozzle with a constant area section in the throat region. Stagnation pressures ranged from slightly above saturation to twice the thermodynamic critical pressure. Stagnation temperatures ranged from 0.75 to 1.03 times the thermodynamic critical temperature. The choking plane is at the divergence end of the constant area throat section. At high stagnation pressures the fluid stays liquid well into the constant area throat region; at near saturation stagnation pressures it appears that vaporization occurs at or before the entrance to the constant area throat region. The throat-to-stagnation pressure ratio data exhibits an anomalous flat region, and this anomaly is related to the two-phase process. The fluid is metastably all liquid below the saturation pressure.

Higher-Quality Weld Joints for Tube Sections

NASA Technical Reports Server (NTRS)

Olszewski, John T.

1987-01-01

Less material in weld inserts results in better fusion. Redesigned insert for joining tubes by welding improves quality of weld. In new insert, leg of T shorter so it does not protrude into tube cavity.

Post-intubation sore throat and menstruation cycles.

PubMed

Orandi, Amirali; Orandi, Amirhossein; Najafi, Atabak; Hajimohammadi, Fatemeh; Soleimani, Sara; Zahabi, Somayeh

2013-09-01

Postoperative sore throat is one of the most common complications of general anesthesia and intubation with prevalence of 18%-65% in different studies. Several risk factors including female gender, postoperative nausea and vomiting and so on have been mentioned. The aim of this study was to evaluate the incidence of postoperative sore throat in females and its association with menstrual cycles. One hundred females between 18-45 years old with ASA class I or II without predicted difficult airway that were candidate for operation in supine position were enrolled in study. Patients who had pulmonary disease, smoking, common cold within two weeks prior to the operation, previous traumatic intubation history, removable dentures, any congenital or acquired deformity in face, neck, mouth and airway, any known pathology in mouth like aphthous and mouth ulcer,pregnant women, and patients with irregular cycles, and those taking oral contraceptive pills were excluded. By the same protocol general anesthesia was provided and the patients were asked to fill out a three-point scale questionnaire (Low, High, None) 1,6 and 24 hours following intubation to study and record the incidence and severity of sore throat, dysphagia and hoarseness. The date of last menstrual period had been recorded as well. Of 100 patients, in the first six hours, 51 patients had sore throat and 49 had no pain. During the first 6 hours, 33 patients (33%) had dysphagia and 13 patients had hoarseness at 6th postoperative hour. Age, weight, LMP, intubation time, operation and extubation time and coughing were compared to sore throat, dysphagia and hoarseness. The association between the incidence of coughing and bucking and sore throat was significant (P = 0.03). None of the parameters had a statistically meaningful association with dysphagia. According to our results, by omitting probable risk factors of incidence of sore throat and evaluation of role of hormonal changes in women represented in menstrual cycles, there was no significant association between menstrual cycle and sore throat incidence.

Multiscale Pore Throat Network Reconstruction of Tight Porous Media Constrained by Mercury Intrusion Capillary Pressure and Nuclear Magnetic Resonance Measurements

NASA Astrophysics Data System (ADS)

Xu, R.; Prodanovic, M.

2017-12-01

Due to the low porosity and permeability of tight porous media, hydrocarbon productivity strongly depends on the pore structure. Effective characterization of pore/throat sizes and reconstruction of their connectivity in tight porous media remains challenging. Having a representative pore throat network, however, is valuable for calculation of other petrophysical properties such as permeability, which is time-consuming and costly to obtain by experimental measurements. Due to a wide range of length scales encountered, a combination of experimental methods is usually required to obtain a comprehensive picture of the pore-body and pore-throat size distributions. In this work, we combine mercury intrusion capillary pressure (MICP) and nuclear magnetic resonance (NMR) measurements by percolation theory to derive pore-body size distribution, following the work by Daigle et al. (2015). However, in their work, the actual pore-throat sizes and the distribution of coordination numbers are not well-defined. To compensate for that, we build a 3D unstructured two-scale pore throat network model initialized by the measured porosity and the calculated pore-body size distributions, with a tunable pore-throat size and coordination number distribution, which we further determine by matching the capillary pressure vs. saturation curve from MICP measurement, based on the fact that the mercury intrusion process is controlled by both the pore/throat size distributions and the connectivity of the pore system. We validate our model by characterizing several core samples from tight Middle East carbonate, and use the network model to predict the apparent permeability of the samples under single phase fluid flow condition. Results show that the permeability we get is in reasonable agreement with the Coreval experimental measurements. The pore throat network we get can be used to further calculate relative permeability curves and simulate multiphase flow behavior, which will provide valuable insights into the production optimization and enhanced oil recovery design.

Constraints on wrapped Dirac-Born-Infeld inflation in a warped throat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kobayashi, Takeshi; Mukohyama, Shinji; Kinoshita, Shunichiro, E-mail: tkobayashi@utap.phys.s.u-tokyo.ac.jp, E-mail: mukoyama@phys.s.u-tokyo.ac.jp, E-mail: kinoshita@utap.phys.s.u-tokyo.ac.jp

2008-01-15

We derive constraints on the tensor to scalar ratio and on the background charge of the warped throat for Dirac-Born-Infeld inflation driven by D5- and D7-branes wrapped over cycles of the throat. It is shown that background charge well beyond the known maximal value is required in most cases for Dirac-Born-Infeld inflation to generate cosmological observables compatible with the WMAP3 (Wilkinson Microwave Anisotropy Probe 3) data. Most of the results derived in this paper are insensitive to the details of the inflaton potential, and could be applied to generic warped throats.

Optimizing Naval Hospital Camp Pendleton’s Primary Care Access by Managing Demand of the Emergency Department through a Health Services Center: A Marcus Welby Care Initiative

DTIC Science & Technology

2006-06-01

10 strep throat . I want to order a throat culture and start you on some antibiotics." As quickly as the doctor appeared, he was gone, moving on to the...TRICARE Prime. She wakes up one morning with an awful sore throat and difficulty swallowing. She tries to contact her Primary Care Manager (PCM) by...next of what seemed a never ending stream of patients. After the throat culture and an additional hour wait at the pharmacy, Mrs. Smith is on her way

Optimization of Tape Winding Process Parameters to Enhance the Performance of Solid Rocket Nozzle Throat Back Up Liners using Taguchi's Robust Design Methodology

NASA Astrophysics Data System (ADS)

Nath, Nayani Kishore

2017-08-01

The throat back up liners is used to protect the nozzle structural members from the severe thermal environment in solid rocket nozzles. The throat back up liners is made with E-glass phenolic prepregs by tape winding process. The objective of this work is to demonstrate the optimization of process parameters of tape winding process to achieve better insulative resistance using Taguchi's robust design methodology. In this method four control factors machine speed, roller pressure, tape tension, tape temperature that were investigated for the tape winding process. The presented work was to study the cogency and acceptability of Taguchi's methodology in manufacturing of throat back up liners. The quality characteristic identified was Back wall temperature. Experiments carried out using L 9 ' (34) orthogonal array with three levels of four different control factors. The test results were analyzed using smaller the better criteria for Signal to Noise ratio in order to optimize the process. The experimental results were analyzed conformed and successfully used to achieve the minimum back wall temperature of the throat back up liners. The enhancement in performance of the throat back up liners was observed by carrying out the oxy-acetylene tests. The influence of back wall temperature on the performance of throat back up liners was verified by ground firing test.

Nozzle Aerodynamic Stability During a Throat Shift

NASA Technical Reports Server (NTRS)

Kawecki, Edwin J.; Ribeiro, Gregg L.

2005-01-01

An experimental investigation was conducted on the internal aerodynamic stability of a family of two-dimensional (2-D) High Speed Civil Transport (HSCT) nozzle concepts. These nozzles function during takeoff as mixer-ejectors to meet acoustic requirements, and then convert to conventional high-performance convergent-divergent (CD) nozzles at cruise. The transition between takeoff mode and cruise mode results in the aerodynamic throat and the minimum cross-sectional area that controls the engine backpressure shifting location within the nozzle. The stability and steadiness of the nozzle aerodynamics during this so called throat shift process can directly affect the engine aerodynamic stability, and the mechanical design of the nozzle. The objective of the study was to determine if pressure spikes or other perturbations occurred during the throat shift process and, if so, identify the caused mechanisms for the perturbations. The two nozzle concepts modeled in the test program were the fixed chute (FC) and downstream mixer (DSM). These 2-D nozzles differ principally in that the FC has a large over-area between the forward throat and aft throat locations, while the DSM has an over-area of only about 10 percent. The conclusions were that engine mass flow and backpressure can be held constant simultaneously during nozzle throat shifts on this class of nozzles, and mode shifts can be accomplished at a constant mass flow and engine backpressure without upstream pressure perturbations.

Fractal Characteristics of the Pore Network in Diatomites Using Mercury Porosimetry and Image Analysis

NASA Astrophysics Data System (ADS)

Stańczak, Grażyna; Rembiś, Marek; Figarska-Warchoł, Beata; Toboła, Tomasz

The complex pore space considerably affects the unique properties of diatomite and its significant potential for many industrial applications. The pore network in the diatomite from the Lower Miocene strata of the Skole nappe (the Jawornik deposit, SE Poland) has been investigated using a fractal approach. The fractal dimension of the pore-space volume was calculated using the Menger sponge as a model of a porous body and the mercury porosimetry data in a pore-throat diameter range between 10,000 and 10 nm. Based on the digital analyses of the two-dimensional images from thin sections taken under a scanning electron microscope at the backscattered electron mode at different magnifications, the authors tried to quantify the pore spaces of the diatomites using the box counting method. The results derived from the analyses of the pore-throat diameter distribution using mercury porosimetry have revealed that the pore space of the diatomite has the bifractal structure in two separated ranges of the pore-throat diameters considerably smaller than the pore-throat sizes corresponding to threshold pressures. Assuming that the fractal dimensions identified for the ranges of the smaller pore-throat diameters characterize the overall pore-throat network in the Jawornik diatomite, we can set apart the distribution of the pore-throat volume (necks) and the pore volume from the distribution of the pore-space volume (pores and necks together).

Validity of rapid antigen detection testing in group A beta-hemolytic streptococcal tonsillopharyngitis.

PubMed

Küçük, Oznur; Biçer, Suat; Giray, Tuba; Cöl, Defne; Erdağ, Gülay Ciler; Gürol, Yeşim; Kaspar, Ciğdem E; Vitrinel, Ayça

2014-02-01

To evaluate the utility of rapid antigen detection testing (RADT) for the diagnosis of group A beta-hemolytic streptococcal tonsillopharyngitis in children, and to detect the sensitivity and specificity of rapid antigen detection of group A beta-hemolytic streptococci from throat specimen compared with throat culture. Rapid antigen detection and throat culture results for group A beta-hemolytic streptococci from outpatients attending university hospital between 1st January 2011 and 31st of December 2011 were evaluated retrospectively. The antigen test negative-throat culture positive patients were investigated for streptococcal carriage. For this purpose, the throat culture results taken from these patients were reviewed after treatment. Eight hundred and ninetytwo children were included in the studywith a mean age of 5.34 y. There were 639 and 253 children in two groups with age of 0-6 and 7-17 y, RADT sensitivity and specificity were found to be 59.5 % and 97.2 %, respectively. The positive predictive value was 87.1 %, whereas negative predictive value was 88.4 %. After treatment of 74 patients with throat culture positive and antigen test negative. Group A beta-hemolytic streptococci were isolated in 12 of them (16.2 %) and accepted as a carrier. The low sensitivity of the RADT may be related to streptococcal carriage in some patients. The throat culture should be repeated after treatment to detect streptococcal carriage.

Streptococcal sore throat followup program in a hospital clinic, New York City.

PubMed Central

Kaufman, A; Murray, D; Starita, L; Brickner, P W

1975-01-01

To improve followup and treatment of patients with streptococcal sore throat at St. Vincent's Hospital and Medical Center, New York City, a simple and inexpensive method was devised for recalling and treating untreated patients with positive throat cultures and culturing household contacts. The program was conducted by a clinic nurse and a secretary, with only occasional assistance from a physician. All services were free for those without Medicaid coverage. The secretary sent notification letters to all patients with positive cultures urging them to return for treatment and emphasizing the need for their contacts to come for screening. The secretary, trained in the throat culturing technique, also performed the laboratory work on the cultures from contacts. The clinic nurse swabbed the throats of all contacts and administered treatment, according to a standing-order protocol, to all with culture-proved streptococcal sore throat. A comparison of initially untreated patients with positive cultures seen 3 months before and 6 months after the program was started revealed that 46 percent returned for treatment after the notification letter was sent; before the program only 21 percent returned for treatment. No attempt had been made to reach household contacts before the program began. The rate of streptococcal sore throat in contacts was 14 percent, and in the clinic patients it was 11 percent during the first 6 months of the program. Images p369-a p371-a PMID:808824

HIV Integration at Certain Sites in Host DNA Is Linked to the Expansion and Persistence of Infected Cells | Poster

Cancer.gov

Editor’s note: This article was originally published on the Center for Cancer Research website. When the Human Immunodeficiency Virus (HIV) infects a cell, the virus inserts a copy of its genetic material into the host cell’s DNA. The inserted genetic material, which is also called a provirus, is used to produce new viruses. Because the viral DNA can be inserted at many sites

Interaction of Highly Underexpanded Jets with Simulated Lunar Surfaces

NASA Technical Reports Server (NTRS)

Stitt, Leonard E.

1961-01-01

Pressure distributions and erosion patterns on simulated lunar surfaces (hard and soft) and interference effects between the surface and two representative lunar vehicles (cylindrical and spherical) were obtained with cold-air jets at various descent heights and nozzle total-pressure ratios up to 288,000. Surface pressure distributions were dependent on both nozzle area ratio and, nozzle contour. Peak pressures obtained with a sonic nozzle agreed closely with those predicted theoretically for a near-sonic jet expanding into a vacuum. Short bell-shaped nozzles gave annular pressure distributions; the low center pressure resulted from the coalescence of shocks that originated within the nozzle. The high surface pressures were contained within a circle whose diameter was about 16 throat diameters, regardless of nozzle area ratio or contour. The peak pressure increased rapidly as the vehicle approached the surface; for example, at a descent height of 40 throat diameters the peak pressure was 0.4 percent of the chamber pressure, but increased to 6 percent at 13 throat diameters. The exhaust jet eroded a circular concave hole in white sand at descent heights from about 200 to 600 throat diameters. The hole diameter was about 225 throat diameters, while the depth was approximately 60 throat diameters. The sand particles, which formed a conical sheet at a semivertex angle of 50 deg, appeared to follow a ballistic trajectory and at no time struck the vehicle. An increase in pressure was measured on the base of the cylindrical lunar vehicle when it approached to within 14 throat diameters of the hard, flat surface. No interference effects were noted between the spherical model and the surface to descent heights as low as 8 throat diameters.

Single bolus parecoxib attenuates sore throat after laryngeal microsurgery: a randomized double-blind control study.

PubMed

Huang, Hui-Fang; Chang, Pi-Ying; Chen, Yu-Chun; Tseng, Kuang-Yi; Hsu, Hung-Te; Cheng, Kuang-I; Lu, I-Cheng

2014-11-01

Laryngeal microsurgery is performed to assess disorders of the larynx. Parecoxib is the only parenterally administered selective cyclooxygenase (COX)-2 inhibitor widely used in acute pain control. The purpose of this study is to assess the analgesic effects of parecoxib compared with morphine for postoperative sore throat in patients undergoing laryngeal microsurgery. Fifty patients were randomly allocated to receive either parecoxib 0.5 mg/kg or morphine 50 μg/kg prior to anesthesia induction. General anesthesia was maintained with sevoflurane 2-4%. Postoperative sore throat and other outcomes were measured at a postanesthesia care unit (PACU) 4 hours and 24 hours postoperatively. The severity of postoperative sore throat was assessed by sore throat score as follows: none (0) = no pharyngeal or laryngeal discomfort; mild (1) = no pain at rest, but swallowing induced mild pain or discomfort; moderate (2) = constant pain without swallowing exacerbation; and severe (3) = constant pain with swallowing or respiratory exacerbation. The incidences of postoperative side effects (nausea, vomiting, itching, dizziness, and somnolence) were also recorded. Demographic data from the parecoxib (n = 25) and morphine (n = 25) groups did not differ significantly. The parecoxib group depicted similar sore throat scores as the morphine group at three measured postoperative time points. Patients requiring postoperative analgesics were comparable between the parecoxib group and morphine group (2/25, 8% vs. 3/25, 12%, p = 0.64). Overall postoperative adverse events were fewer in the parecoxib group than the morphine group (3/25, 12% vs. 9/25, 36%, p = 0.047). Both parecoxib and morphine are effective to attenuate postoperative sore throat after laryngeal microsurgery. Parecoxib may be an effective and well-tolerated injectable analgesic to manage postoperative sore throat after laryngeal microsurgery. Copyright © 2014. Published by Elsevier Taiwan.

Combined Use of Standard and Throat Microphones for Measurement of Acoustic Voice Parameters and Voice Categorization.

PubMed

Uloza, Virgilijus; Padervinskis, Evaldas; Uloziene, Ingrida; Saferis, Viktoras; Verikas, Antanas

2015-09-01

The aim of the present study was to evaluate the reliability of the measurements of acoustic voice parameters obtained simultaneously using oral and contact (throat) microphones and to investigate utility of combined use of these microphones for voice categorization. Voice samples of sustained vowel /a/ obtained from 157 subjects (105 healthy and 52 pathological voices) were recorded in a soundproof booth simultaneously through two microphones: oral AKG Perception 220 microphone (AKG Acoustics, Vienna, Austria) and contact (throat) Triumph PC microphone (Clearer Communications, Inc, Burnaby, Canada) placed on the lamina of thyroid cartilage. Acoustic voice signal data were measured for fundamental frequency, percent of jitter and shimmer, normalized noise energy, signal-to-noise ratio, and harmonic-to-noise ratio using Dr. Speech software (Tiger Electronics, Seattle, WA). The correlations of acoustic voice parameters in vocal performance were statistically significant and strong (r = 0.71-1.0) for the entire functional measurements obtained for the two microphones. When classifying into healthy-pathological voice classes, the oral-shimmer revealed the correct classification rate (CCR) of 75.2% and the throat-jitter revealed CCR of 70.7%. However, combination of both throat and oral microphones allowed identifying a set of three voice parameters: throat-signal-to-noise ratio, oral-shimmer, and oral-normalized noise energy, which provided the CCR of 80.3%. The measurements of acoustic voice parameters using a combination of oral and throat microphones showed to be reliable in clinical settings and demonstrated high CCRs when distinguishing the healthy and pathological voice patient groups. Our study validates the suitability of the throat microphone signal for the task of automatic voice analysis for the purpose of voice screening. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Evaluation of a streptococcal pharyngitis score in southern Taiwan.

PubMed

Shih, Ching-Tang; Lin, Ching-Chiang; Lu, Chung-Ching

2012-02-01

Group A streptococcus (GAS) pharyngitis can cause serious complications such as rheumatic heart disease. The McIsaac sore throat score is a clinical prediction score used to improve the detection rate of GAS pharyngitis. We evaluated the validity of the McIsaac sore throat score in Southern Taiwan and compared our findings to those of other studies. We retrospectively analyzed chart records from children aged 3 to 15 years old who complained of fever and sore throat. They had throat cultures collected at the outpatient pediatric clinic of Fooyin University Hospital, located in Pingtung County, Taiwan during the period between January 2007 and January 2010. Clinical characteristics were reviewed, and sore throat score was analyzed. A total of 342 throat cultures met the inclusion criteria of sore throat and fever. The positive rate of GAS was 4.1%. Culture-positive cases were associated with higher odds for a skin rash [adjusted odds ratio (AOR): 14.66, 95% confidence interval (CI): 4.63-46.40, p < 0.001), lower odds for cough (AOR: 0.19, 95% CI: 0.04-0.85, p = 0.030) and having a runny nose (AOR: 0.22, 95% CI: 0.05-0.99, p = 0.048). The most common physical sign was scarlet fever rash (AOR: 57.35, 95% CI: 15.45-212.98, p < 0.001). A McIsaac score of 5 had a sensitivity of 71%, specificity of 70%, and a positive predictive value of only 9.3%. Pediatric streptococcal pharyngitis in Southern Taiwan is uncommon. Diagnosis of GAS pharyngitis based on the McIsaac sore throat score is unreliable among pediatric patients with febrile pharyngitis in Southern Taiwan. Copyright © 2012. Published by Elsevier B.V.

Etiologic predictive value of a rapid immunoassay for the detection of group A Streptococcus antigen from throat swabs in patients presenting with a sore throat.

PubMed

Orda, Ulrich; Gunnarsson, Ronny; Orda, Sabine; Fitzgerald, Mark; Rofe, Geoff; Dargan, Anna

2016-04-01

Clinical reasoning utilizing certain symptoms and scores has not proven to be a reliable decision-making tool to determine whether or not to suspect a group A Streptococcus (GAS) infection in the patient presenting with a sore throat. Culture as the so-called 'gold standard' is impracticable because it takes 1 to 2 days (and even longer in remote locations) for a result, and thus treatment decisions will be made without the result available. Rapid diagnostic antigen tests have demonstrated sufficient sensitivities and specificities in detecting GAS antigens to identify GAS throat infections. Throat swab samples were collected from patients attending the Mount Isa Hospital emergency department for a sore throat; these samples were compared to swab samples collected from healthy controls who did not have a sore throat. Both groups were aged 3-15 years. All swab samples were analyzed with a point-of-care test (Alere Test Pack +Plus with OBC Strep A). The etiologic predictive value (EPV) of the throat swab was calculated. The 95% confidence interval for positive EPV was 88-100% and for negative EPV was 97-99%, depending on assumptions made. This study demonstrates that the point-of-care test Alere Test Pack +Plus Strep A has a high positive predictive value and is able to rule in GAS infection as long as the proportion of carriers is low. Also the negative predictive value for ruling out GAS as the etiologic agent is very high irrespective of the carrier rate. Hence, this test is always useful to rule out GAS infection. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

An intelligent artificial throat with sound-sensing ability based on laser induced graphene

PubMed Central

Tao, Lu-Qi; Tian, He; Liu, Ying; Ju, Zhen-Yi; Pang, Yu; Chen, Yuan-Quan; Wang, Dan-Yang; Tian, Xiang-Guang; Yan, Jun-Chao; Deng, Ning-Qin; Yang, Yi; Ren, Tian-Ling

2017-01-01

Traditional sound sources and sound detectors are usually independent and discrete in the human hearing range. To minimize the device size and integrate it with wearable electronics, there is an urgent requirement of realizing the functional integration of generating and detecting sound in a single device. Here we show an intelligent laser-induced graphene artificial throat, which can not only generate sound but also detect sound in a single device. More importantly, the intelligent artificial throat will significantly assist for the disabled, because the simple throat vibrations such as hum, cough and scream with different intensity or frequency from a mute person can be detected and converted into controllable sounds. Furthermore, the laser-induced graphene artificial throat has the advantage of one-step fabrication, high efficiency, excellent flexibility and low cost, and it will open practical applications in voice control, wearable electronics and many other areas. PMID:28232739

An intelligent artificial throat with sound-sensing ability based on laser induced graphene.

PubMed

Tao, Lu-Qi; Tian, He; Liu, Ying; Ju, Zhen-Yi; Pang, Yu; Chen, Yuan-Quan; Wang, Dan-Yang; Tian, Xiang-Guang; Yan, Jun-Chao; Deng, Ning-Qin; Yang, Yi; Ren, Tian-Ling

2017-02-24

Traditional sound sources and sound detectors are usually independent and discrete in the human hearing range. To minimize the device size and integrate it with wearable electronics, there is an urgent requirement of realizing the functional integration of generating and detecting sound in a single device. Here we show an intelligent laser-induced graphene artificial throat, which can not only generate sound but also detect sound in a single device. More importantly, the intelligent artificial throat will significantly assist for the disabled, because the simple throat vibrations such as hum, cough and scream with different intensity or frequency from a mute person can be detected and converted into controllable sounds. Furthermore, the laser-induced graphene artificial throat has the advantage of one-step fabrication, high efficiency, excellent flexibility and low cost, and it will open practical applications in voice control, wearable electronics and many other areas.

Genetic Diversity among Group A Streptococcus Isolated from Throats of Healthy and Symptomatic Children

PubMed Central

Kashyap, Nitin; Kanga, Anil; Thakur, Kamlesh; Sood, Anuradha; Chandel, Lata

2016-01-01

Background: Group A streptococcus (GAS) is the commonest bacterial cause of pharyngitis. Children in the age group of 5–15 years are most commonly affected. It can also colonize throats of healthy children in this age group. Both cases and carriers can transmit it in the community. Methods: Throat swab samples were collected from 1849 asymptomatic and 371 symptomatic children. Results: The rate of isolation of GAS was 1.41% among the asymptomatic group and 7.55% among the symptomatic group. Nine different emm types were encountered in the asymptomatic children and 14 among the symptomatic children. Conclusion: Throat swab cultures must be used in all cases of pharyngitis. Early and appropriate antibiotic therapy will prevent complications. Asymptomatic throat carriage of GAS in children was low in our study. However, they can still act as reservoirs. Emm typing helps in understanding epidemiology and finding new types. PMID:26743337

Response to nestling throat ligatures by three songbirds

USGS Publications Warehouse

Robinson, G.L.; Conway, C.J.; Kirkpatrick, C.; Laroche, D.D.

2010-01-01

We attempted to collect diet samples using throat ligatures from nestlings of three songbird species in a riparian woodland in southeastern Arizona from May to August 2009. We had success with Song Sparrows (Melospiza melodia), observed adult Yellow-breasted Chats (Icteria virens) reclaim food from nestlings, and discontinued the use of throat ligatures when we observed an adult Abert's Towhee (Pipilo aberti) remove two, 34-day-old ligatured nestlings from its nest. Previous studies have reported problems (e.g., aggression toward nestlings by adults) with throat ligatures, but we are the first to document removal (and subsequent nestling mortality) in response to this technique. We urge investigators to exercise caution when using throat ligatures on species for which evidence of the safety and efficacy of this method are lacking, especially when nestlings are small in size relative to adults. ?? 2010 by the Wilson Ornithological Society.

An intelligent artificial throat with sound-sensing ability based on laser induced graphene

NASA Astrophysics Data System (ADS)

Tao, Lu-Qi; Tian, He; Liu, Ying; Ju, Zhen-Yi; Pang, Yu; Chen, Yuan-Quan; Wang, Dan-Yang; Tian, Xiang-Guang; Yan, Jun-Chao; Deng, Ning-Qin; Yang, Yi; Ren, Tian-Ling

2017-02-01

Traditional sound sources and sound detectors are usually independent and discrete in the human hearing range. To minimize the device size and integrate it with wearable electronics, there is an urgent requirement of realizing the functional integration of generating and detecting sound in a single device. Here we show an intelligent laser-induced graphene artificial throat, which can not only generate sound but also detect sound in a single device. More importantly, the intelligent artificial throat will significantly assist for the disabled, because the simple throat vibrations such as hum, cough and scream with different intensity or frequency from a mute person can be detected and converted into controllable sounds. Furthermore, the laser-induced graphene artificial throat has the advantage of one-step fabrication, high efficiency, excellent flexibility and low cost, and it will open practical applications in voice control, wearable electronics and many other areas.

Shock position sensor for supersonic inlets. [measuring pressure in the throat of a supersonic inlet

NASA Technical Reports Server (NTRS)

Dustin, M. O. (Inventor)

1975-01-01

Static pressure taps or ports are provided in the throat of a supersonic inlet, and signals indicative of the pressure at each of the ports is fed to respective comparators. Means are also provided for directing a signal indicative of the total throat pressure to the comparators. A periodic signal is superimposed on the total throat pressure so that the signal from the static pressure tabs is compared to a varying scan signal rather than to total throat pressure only. This type of comparison causes each comparator to provide a pulse width modulated output which may vary from 0% 'time on' to 100% 'time on'. The pulse width modulated outputs of the comparators are summed, filtered, and directed to a controller which operates a bypass valve such as a door whereby air is dumped from the inlet to prevent the shock wave from being expelled out the front.

Epizootiology of arenaviral infections in the white-throated woodrat (Muridae: Sigmodontinae) and other woodrats in Arizona.

PubMed

Abbott, Ken D; Milazzo, Mary L; Keith, Josh; Bradley, Robert D; Fulhorst, Charles F

2004-12-01

The purpose of this study was to extend and refine our knowledge of the geographical distribution and natural host relationships of the arenaviruses associated with woodrats indigenous to Arizona. Antibody to a Tacaribe serocomplex virus was found in 112 of 1,250 white-throated woodrats, five of 208 Mexican woodrats, one of 114 Stephen's woodrats, and none of 862 other rodents captured at 51 sites in 10 counties in Arizona. Of the 112 antibody-positive white-throated woodrats, 109 (97.3%) were captured within extensive, dense patches of prickly pear cactus and cane cholla in three counties in mid-central Arizona. Analysis of the serological and zoographical data suggested that white-throated woodrats usually become infected early in life and that the distribution of antibody-positive white-throated woodrats in Arizona is not linked to a specific biome.

Qualities of Sore Throat Index (QuaSTI): measuring descriptors of sore throat in a randomized, placebo-controlled trial.

PubMed

Schachtel, Bernard; Shephard, Adrian; Schachtel, Emily; Lorton, Mary Beth; Shea, Tim; Aspley, Sue

2018-03-01

Patients with pharyngitis often describe various sensory, affective and evaluative pain qualities. Using an 11-word/phrase index, the Qualities of Sore Throat Index (QuaSTI), we characterized throat symptoms and evaluated changes in a randomized controlled trial (NCT01986361). Patients received a single flurbiprofen 8.75 mg (n = 101) or placebo (n = 21) lozenge and rated throat soreness at baseline and regular intervals over 3 h, and the QuaSTI at baseline, 1, 2 and 3 h post-treatment. The QuaSTI distinguished active drug from placebo and detected clinically important (≥2-point) changes over 3 h. Mean change from baseline over 3 h was significantly greater for flurbiprofen (154%) than placebo (p < 0.05). The QuaSTI is a sensitive instrument for measuring therapeutic effects in patients with pharyngitis.

Extreme throat initial data set and horizon area-angular momentum inequality for axisymmetric black holes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dain, Sergio; Max Planck Institute for Gravitational Physics

2010-11-15

We present a formula that relates the variations of the area of extreme throat initial data with the variation of an appropriate defined mass functional. From this expression we deduce that the first variation, with fixed angular momentum, of the area is zero and the second variation is positive definite evaluated at the extreme Kerr throat initial data. This indicates that the area of the extreme Kerr throat initial data is a minimum among this class of data. And hence the area of generic throat initial data is bounded from below by the angular momentum. Also, this result strongly suggestsmore » that the inequality between area and angular momentum holds for generic asymptotically flat axially symmetric black holes. As an application, we prove this inequality in the nontrivial family of spinning Bowen-York initial data.« less

Reversible magnesium and aluminium ions insertion in cation-deficient anatase TiO2

NASA Astrophysics Data System (ADS)

Koketsu, Toshinari; Ma, Jiwei; Morgan, Benjamin J.; Body, Monique; Legein, Christophe; Dachraoui, Walid; Giannini, Mattia; Demortière, Arnaud; Salanne, Mathieu; Dardoize, François; Groult, Henri; Borkiewicz, Olaf J.; Chapman, Karena W.; Strasser, Peter; Dambournet, Damien

2017-11-01

In contrast to monovalent lithium or sodium ions, the reversible insertion of multivalent ions such as Mg2+ and Al3+ into electrode materials remains an elusive goal. Here, we demonstrate a new strategy to achieve reversible Mg2+ and Al3+ insertion in anatase TiO2, achieved through aliovalent doping, to introduce a large number of titanium vacancies that act as intercalation sites. We present a broad range of experimental and theoretical characterizations that show a preferential insertion of multivalent ions into titanium vacancies, allowing a much greater capacity to be obtained compared to pure TiO2. This result highlights the possibility to use the chemistry of defects to unlock the electrochemical activity of known materials, providing a new strategy for the chemical design of materials for practical multivalent batteries.

Effect of inserted metal at anode tip on formation of pulsed X-ray emitting zone of plasma focus device

NASA Astrophysics Data System (ADS)

Miremad, Seyed Milad; Shirani Bidabadi, Babak

2018-04-01

The effect of the anode's insert material of a plasma focus device on the properties of X-ray emission zone was studied. Inserts were fabricated out of six different materials including aluminum, copper, zinc, tin, tungsten, and lead to cover a wide range of atomic numbers. For each anode's insert material at different gas pressures and different voltages, the shape of X-ray emission zone was recorded by three pinhole cameras, which were installed on sidewall and roof of the chamber of plasma focus device. The results indicated that by changing the gas pressure and the charge voltage of capacitor, the X-ray source of plasma focus emerges with different forms as a concentrated column or conical shape with sharp or cloudy edges. These structures are in the form of a combination of plasma emission and anode-tip emission with different intensities. These observations indicate that the material of the anode-tip especially affects the structure of X-ray emission zone.

NASA/First Materials Science Research Rack (MSRR-1) Module Inserts Development for the International Space Station

NASA Technical Reports Server (NTRS)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

1999-01-01

The Material Science Research Rack 1 (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit. Two of the NASA MIs being developed for specific material science investigations are described herein.

MX Siting Investigation. DTN/OBTS Field Surveys. Volume III. Biological Resources Nevada and Utah.

DTIC Science & Technology

1981-11-30

Black - throated sparrow (Amphispiza bilineata) X X X REPTILES Desert tortoise (Gopherus agassizi) X X Zebra-tailed...observed on the greatest number of sites was the black - throated sparrow (Amphispiza bilineata). The reptile most frequently observed was the side-blotched...Poliopt~ila caerula Loggerhead shrike Lanius ludovicianus Black - throated sparrow Amphispiza bilineata Unidentified sparrow Unidentified buteo REPTILES

21 CFR 874.4350 - Ear, nose, and throat fiberoptic light source and carrier.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ear, nose, and throat fiberoptic light source and carrier. 874.4350 Section 874.4350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... of plastic fibers and that is intended to provide illumination at the tip of an ear, nose, or throat...

Physical Standards for Appointment , Enlistment, and Induction

DTIC Science & Technology

1994-05-02

Pharynx , Trachea, and Larynx 1-24 Y. Other Defects and Diseases of the Mouth, Nose , Throat , Pharynx , and...or conditions of the mouth, tongue, throat , pharynx , larynx , and nose that interfere with mastication and swallowing of ordinary food, or with speech...Tracheostomy or tracheal fistula. y. OTHER DEFECTS AND DISEASES OF THEMOUTH. NOSE . THROAT . PARYNXAND LARYNX The causes for rejection for

Metal atomization spray nozzle

DOEpatents

Huxford, Theodore J.

1993-01-01

A spray nozzle for a magnetohydrodynamic atomization apparatus has a feed passage for molten metal and a pair of spray electrodes mounted in the feed passage. The electrodes, diverging surfaces which define a nozzle throat and diverge at an acute angle from the throat. Current passes through molten metal when fed through the throat which creates the Lorentz force necessary to provide atomization of the molten metal.

Throat-bypass bleed systems for increasing the stable airflow range of a Mach 2.50 axisymmetric inlet with 40-percent internal contraction

NASA Technical Reports Server (NTRS)

Sanders, B. W.; Mitchell, G. A.

1973-01-01

The results of an experimental investigation to increase the stable airflow range of a super sonic mixed-compression inlet are presented. Various throat-bypass bleeds were located on the inlet cowl. The bleed types were distributed porous normal holes, a forward slanted slot, or distributed educated slots. Large inlet stability margins were obtained with the inlet throat bleed systems if a constant pressure was maintained in the throat-bypass bleed plenum. Stability limits were determined for steady-state and limited transient internal air flow changes. Limited unstart angle-of-attack data are presented.

Incidence angle bounds for lip flow separation of three 13.97-centimeter-diameter inlets

NASA Technical Reports Server (NTRS)

Luidens, R. W.; Abbott, J. M.

1976-01-01

Low speed wind tunnel tests were conducted to establish a procedure for determining inlet-lip flow separation and to make preliminary examination of the incidence angle bounds for lip flow separation on inlets intended for the nacelles of STOL (short takeoff and landing) aircraft. Three inlets were tested. Two of the inlets had short centerbodies with lower lip area contraction ratios of 1.30 and 1.44. The third inlet had a cylindrical centerbody extended forward into the inlet throat with a lower lip area contraction ratio of 1.44. The inlets were sized to fit a 13.97 centimeter-diameter fan. For inlet throat Mach numbers less than about 0.43, the lip flow separation angle was increased by either increasing the ratio of throat velocity to freestream velocity (Vt/Vo) or by increasing the lower lip area contraction ratio. For throat Mach numbers greater than a certain value (ranging from 0.43 to 0.52), increasing throat Mach number in some cases resulted in a decrease in the lip flow separation angle. Extending a cylindrical centerbody into the inlet throat increased the flow separation angle for nearly all values of Vt/Vo.

Does cuff pressure monitoring reduce postoperative pharyngolaryngeal adverse events after LMA-ProSeal insertion? A parallel group randomised trial.

PubMed

Vasanth Karthik, R; Ranganathan, Priya; Kulkarni, Atul P; Sharma, Kailash S

2014-10-01

The incidence of postoperative pharyngolaryngeal complications after laryngeal mask airway (LMA) insertion can be as high as 50%. Over-inflation of the LMA cuff may be a causal factor. We conducted a single-centre parallel group randomised trial to determine whether maintaining LMA-ProSeal intra-cuff pressures below 60 cm H2O decreases postoperative pharyngolaryngeal complications. We recruited 120 adult patients who were scheduled to undergo elective surgery under general anaesthesia. Appropriate sized LMA-ProSeal was inserted and the cuff was inflated with air (to no more than the maximum recommended volume) until there was no audible leak. Patients were randomised to either the control group (n = 60), where the intra-cuff pressure was noted and no further action was taken, or to the pressure-monitored group (n = 60), where intra-cuff pressure was maintained below 60 cm H2O. Pharyngolaryngeal complications consisting of sore throat, dysphonia and dysphagia were assessed at 1, 2, and 24 h postoperatively. Patients, anaesthesiologists and assessors were blinded to group allocation. The primary outcome was a composite endpoint of any pharyngolaryngeal complication at any of the three time points. Secondary outcomes were the incidence of individual outcomes at each time point. The incidence of pharyngolaryngeal complications at any time point was 42% in the routine care group and 32% in the pressure-monitored group (95% CI for difference +28 to -7%, p = 0.26). There was no difference between groups for any of the secondary outcomes. Our study failed to demonstrate a statistically significant reduction in postoperative pharyngolaryngeal complications by limiting intra-cuff pressures in the LMA-Proseal.

Fully Coupled Aero-Thermochemical-Elastic Simulations of an Eroding Graphite Nozzle

NASA Technical Reports Server (NTRS)

Blades, E. L.; Reveles, N. D.; Nucci, M.; Maclean, M.

2017-01-01

A multiphysics simulation capability has been developed that incorporates mutual interactions between aerodynamics, structural response from aero/thermal loading, ablation/pyrolysis, heating, and surface-to-surface radiation to perform high-fidelity, fully coupled aerothermoelastic ablation simulations, which to date had been unattainable. The multiphysics framework couples CHAR (a 3-D implicit charring ablator solver), Loci/CHEM (a computational fluid dynamics solver for high-speed chemically reacting flows), and Abaqus (a nonlinear structural dynamics solver) to create a fully coupled aerothermoelastic charring ablative solver. The solvers are tightly coupled in a fully integrated fashion to resolve the effects of the ablation pyrolysis and charring process and chemistry products upon the flow field, the changes in surface geometry due to recession upon the flow field, and thermal-structural analysis of the body from the induced aerodynamic heating from the flow field. The multiphysics framework was successfully demonstrated on a solid rocket motor graphite nozzle erosion application. Comparisons were made with available experimental data that measured the throat erosion during the motor firing. The erosion data is well characterized, as the test rig was equipped with a windowed nozzle section for real-time X-ray radiography diagnostics of the instantaneous throat variations for deducing the instantaneous erosion rates. The nozzle initially undergoes a nozzle contraction due to thermal expansion before ablation effects are able to widen the throat. A series of parameters studies were conducted using the coupled simulation capability to determine the sensitivity of the nozzle erosion to different parameters. The parameter studies included the shape of the nozzle throat (flat versus rounded), the material properties, the effect of the choice of turbulence model, and the inclusion or exclusion of the mechanical thermal expansion. Overall, the predicted results match the experiment very well, and the predictions were able to bound the data within acceptable limits.

HIV Integration at Certain Sites in Host DNA is Linked to the Expansion and Persistence of Infected Cells | Center for Cancer Research

Cancer.gov

When the Human Immunodeficiency Virus (HIV) infects a cell, the virus inserts a copy of its genetic material into the host cell’s DNA. The inserted genetic material, which is also called a provirus, is used to produce new viruses. Because the viral DNA can be inserted at many sites in the host cell DNA, the site of integration marks each infected cell. Patients infected with

American River Watershed Investigation, California. Volume 3. Appendix M

DTIC Science & Technology

1991-12-01

curing of the concrete and for general construction. The water used in concrete mixes must be free from injurious materials. Water from the American River...in achieving the desired bond strength between lifts. Water is needed for curing and to maintain freshness of lift joints. Lift surfaces should be kept...dizziness, throat pain, breathing difficulty and coughing . The health effects caused by combined concentrations of certain sulfur oxides and ozone

Dexpanthenol pastille and benzydamine hydrochloride spray for the prevention of post-operative sore throat.

PubMed

Gulhas, N; Canpolat, H; Cicek, M; Yologlu, S; Togal, T; Durmus, M; Ozcan Ersoy, M

2007-02-01

In this study, we aimed to compare the effectiveness of dexpanthenol pastille and benzydamine hydrochloride spray on the prevention of a sore throat. One hundred and eighty patients undergoing general anaesthesia, who were ASA I-II and with their ages ranging between 15 and 70 years, were randomly allocated to three groups, each consisting of 60 patients. For group B, four puffs of benzydamine hydrochloride were sprayed into the mouth initially 30 min before the operation and repeatedly 5 min before anaesthesia induction. For group D, two pastilles of dexpanthenol were administered orally to be sucked 30 min before the operation. For group P, four puffs of distilled water were sprayed into the mouth initially 30 min before the operation. Post-operatively, patients were evaluated for a sore throat for the duration of 24 h. The incidence of a sore throat was significantly lower for group D when compared with group B and group P. The incidence of a sore throat was similar for group B and group P. According to the sore throat grading system, the number of patients experiencing no complaints was significantly higher for group D when compared with group B and group P. The number of patients achieving moderate scores was significantly higher for group B when compared with group D. The administration of 200 mg of dexpanthenol prophylactically before endotracheal intubation is effective in the prevention of post-operative sore throat.

Speech intelligibility in noise using throat and acoustic microphones.

PubMed

Acker-Mills, Barbara E; Houtsma, Adrianus J M; Ahroon, William A

2006-01-01

Helicopter cockpits are very noisy and this noise must be reduced for effective communication. The standard U.S. Army aviation helmet is equipped with a noise-canceling acoustic microphone, but some ambient noise still is transmitted. Throat microphones are not sensitive to air molecule vibrations and thus, transmittal of ambient noise is reduced. It is possible that throat microphones could enhance speech communication in helicopters, but speech intelligibility with the devices must first be assessed. In the current study, speech intelligibility of signals generated by an acoustic microphone, a throat microphone, and by the combined output of the two microphones was assessed using the Modified Rhyme Test (MRT). Stimulus words were recorded in a reverberant chamber with ambient broadband noise intensity at 90 and 106 dBA. Listeners completed the MRT task in the same settings, thus simulating the typical environment of a rotary-wing aircraft. Results show that speech intelligibility is significantly worse for the throat microphone (average percent correct = 55.97) than for the acoustic microphone (average percent correct = 69.70), particularly for the higher noise level. In addition, no benefit is gained by simultaneously using both microphones. A follow-up experiment evaluated different consonants using the Diagnostic Rhyme Test and replicated the MRT results. The current results show that intelligibility using throat microphones is poorer than with the use of boom microphones in noisy and in quiet environments. Therefore, throat microphones are not recommended for use in any situation where fast and accurate speech intelligibility is essential.

Experimental analysis of SiC-based refractory concrete in hybrid rocket nozzles

NASA Astrophysics Data System (ADS)

D'Elia, Raffaele; Bernhart, Gérard; Hijlkema, Jouke; Cutard, Thierry

2016-09-01

Hybrid propulsion represents a good alternative to the more widely used liquid and solid systems. This technology combines some important specifications of the latters, as the possibility of re-ignition, thrust modulation, a higher specific impulse than solid systems, a greater simplicity and a lower cost than liquid systems. Nevertheless the highly oxidizing environment represents a major problem as regards the thermo-oxidation and ablative behavior of nozzle materials. The main goal of this research is to characterize a silicon carbide based micro-concrete with a maximum aggregates size of 800 μm, in a hybrid propulsion environment. The nozzle throat has to resist to a highly oxidizing polyethylene/nitrous oxide hybrid environment, under temperatures up to 2900 K. Three tests were performed on concrete-based nozzles in HERA Hybrid Rocket Motor (HRM) test bench at ONERA. Pressure chamber evolution and observations before and after tests are used to investigate the ablated surface at nozzle throat. Ablation behavior and crack generation are discussed and some improvements are proposed.

Synthetic scaffolds with full pore interconnectivity for bone regeneration prepared by supercritical foaming using advanced biofunctional plasticizers.

PubMed

Salerno, Aurelio; Diéguez, Sara; Diaz-Gomez, Luis; Gómez-Amoza, José L; Magariños, Beatriz; Concheiro, Angel; Domingo, Concepción; Alvarez-Lorenzo, Carmen; García-González, Carlos A

2017-06-30

Supercritical foaming allows for the solvent-free processing of synthetic scaffolds for bone regeneration. However, the control on the pore interconnectivity and throat pore size with this technique still needs to be improved. The use of plasticizers may help overcome these limitations. Eugenol, a GRAS natural compound extracted from plants, is proposed in this work as an advanced plasticizer with bioactive properties. Eugenol-containing poly(ε-caprolactone) (PCL) scaffolds were obtained by supercritical foaming (20.0 MPa, 45 °C, 17 h) followed by a one or a two-step depressurization profile. The effects of the eugenol content and the depressurization profile on the porous structure of the material and the physicochemical properties of the scaffold were evaluated. The combination of both processing parameters was successful to simultaneously tune the pore interconnectivity and throat sizes to allow mesenchymal stem cells infiltration. Scaffolds with eugenol were cytocompatible, presented antimicrobial activity preventing the attachment of Gram positive (S. aureus, S. epidermidis) bacteria and showed good tissue integration.

Aeroelastic Flutter Behavior of a Cantilever and Elastically Mounted Plate within a Nozzle-Diffuser Geometry

NASA Astrophysics Data System (ADS)

Tosi, Luis Phillipe; Colonius, Tim; Lee, Hyeong Jae; Sherrit, Stewart; Jet Propulsion Laboratory Collaboration; California Institute of Technology Collaboration

2016-11-01

Aeroelastic flutter arises when the motion of a structure and its surrounding flowing fluid are coupled in a constructive manner, causing large amplitudes of vibration in the immersed solid. A cantilevered beam in axial flow within a nozzle-diffuser geometry exhibits interesting resonance behavior that presents good prospects for internal flow energy harvesting. Different modes can be excited as a function of throat velocity, nozzle geometry, fluid and cantilever material parameters. Similar behavior has been also observed in elastically mounted rigid plates, enabling new designs for such devices. This work explores the relationship between the aeroelastic flutter instability boundaries and relevant non-dimensional parameters via experiments, numerical, and stability analyses. Parameters explored consist of a non-dimensional stiffness, a non-dimensional mass, non-dimensional throat size, and Reynolds number. A map of the system response in this parameter space may serve as a guide to future work concerning possible electrical output and failure prediction in harvesting devices.

Advanced Monitoring of Migratory Birds on Military Lands

DTIC Science & Technology

2010-03-01

BRSP Brewer‟s Sparrow BTSP Black - throated Sparrow BLGR Blue Grosbeak CAKI Cassin‟s Kingbird CONI Common Nighthawk EAME Eastern...Fuller et al. 1998). This approach has been used for many species, ranging from Black - throated Sparrow (Amphispiza bilineata, Pidgeon et al 2003) to...lightest yellow indicates a predicted abundance of zero. Species acronym key: BTSP Black - throated Sparrow ; EAME Eastern Meadowlark; WEKI Western

Metal atomization spray nozzle

DOEpatents

Huxford, T.J.

1993-11-16

A spray nozzle for a magnetohydrodynamic atomization apparatus has a feed passage for molten metal and a pair of spray electrodes mounted in the feed passage. The electrodes, diverging surfaces which define a nozzle throat and diverge at an acute angle from the throat. Current passes through molten metal when fed through the throat which creates the Lorentz force necessary to provide atomization of the molten metal. 6 figures.

Reversible magnesium and aluminium ions insertion in cation-deficient anatase TiO 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koketsu, Toshinari; Ma, Jiwei; Morgan, Benjamin J.

In contrast to monovalent lithium or sodium ions, the reversible insertion of multivalent ions such as Mg 2+ and Al 3+ into electrode materials remains an elusive goal. In this work, we demonstrate a new strategy to achieve reversible Mg 2+ and Al 3+ insertion in anatase TiO 2, achieved through aliovalent doping, to introduce a large number of titanium vacancies that act as intercalation sites. We present a broad range of experimental and theoretical characterizations that show a preferential insertion of multivalent ions into titanium vacancies, allowing a much greater capacity to be obtained compared to pure TiO 2.more » In conclusion, this result highlights the possibility to use the chemistry of defects to unlock the electrochemical activity of known materials providing a new strategy for the chemical design of materials for practical multivalent batteries.« less

Reversible magnesium and aluminium ions insertion in cation-deficient anatase TiO 2

DOE PAGES

Koketsu, Toshinari; Ma, Jiwei; Morgan, Benjamin J.; ...

2017-09-18

In contrast to monovalent lithium or sodium ions, the reversible insertion of multivalent ions such as Mg 2+ and Al 3+ into electrode materials remains an elusive goal. In this work, we demonstrate a new strategy to achieve reversible Mg 2+ and Al 3+ insertion in anatase TiO 2, achieved through aliovalent doping, to introduce a large number of titanium vacancies that act as intercalation sites. We present a broad range of experimental and theoretical characterizations that show a preferential insertion of multivalent ions into titanium vacancies, allowing a much greater capacity to be obtained compared to pure TiO 2.more » In conclusion, this result highlights the possibility to use the chemistry of defects to unlock the electrochemical activity of known materials providing a new strategy for the chemical design of materials for practical multivalent batteries.« less

Space Shuttle Projects

NASA Image and Video Library

1991-07-01

This photograph shows the Solid Propellant Test Article (SPTA) test stand with the Modified Nasa Motor (M-NASA) test article at the Marshall Space Flight Center (MSFC). The SPTA test stand, 12-feet wide by 12-feet long by 24-feet high, was built in 1989 to provide comparative performance data on nozzle and case insulation material and to verify thermostructural analysis models. A modified NASA 48-inch solid motor (M-NASA motor) with a 12-foot blast tube and 10-inch throat makes up the SPTA. The M-NASA motor is being used to evaluate solid rocket motor internal non-asbestos insulation materials, nozzle designs, materials, and new inspection techniques. New internal motor case instrumentation techniques are also being evaluated.

Refractory electrodes for joule heating and methods of using same

DOEpatents

Lamar, David A.; Chapman, Chris C.; Elliott, Michael L.

1998-01-01

A certain group of electrically conductive refractory materials presently known for use in high temperature applications as throat constructions, melter sidewalls, forehearth, stacks, port sills, hot face lining for slagging coal gasifiers, slag runners, and linings for nuclear waste encapsulation furnaces may be used as electrodes permitting joule heating at temperatures in excess of 1200 C. in excess of about 4400 hours even in the presence of transition group element(s). More specifically, the invention is an electrode for melting earthen materials, wherein the electrode is made from an electrically conductive refractory material, specifically at least one metal oxide wherein the metal is selected from the group consisting of chrome, ruthenium, rhodium, tin and combinations thereof.

Design and testing of microfabricated surgical tools for large animal probe insertion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jorgensen, Shelly

Neural probes provide therapeutic stimulation for neuropsychiatric disorders or record neural activity to investigate the workings of the brain. Researchers utilize 6 mm long temporary silicon stiffeners attached with biodissolvable adhesive to insert flexible neural probes into rat brains, but increasing the probe length fivefold makes inserting large animal probes a significant challenge because of an increased potential for buckling. This study compared the insertion success rates of 6 mm and 30 mm long silicon stiffeners that were 80 μm wide and 30 μm thick, and ascertained the material thickness and modulus of elasticity that would provide successful insertion formore » a 30 mm probe. Using a microdrive, stiffeners were inserted into an agarose brain phantom at controlled insertion speeds while being video-recorded. Twenty-five percent of the 30 mm silicon stiffeners fully inserted at speeds approximately four times higher than the target rate of 0.13 mm/s, while 100 percent of the 6 mm silicon stiffeners inserted successfully at target speed. Critical buckling loads (P cr) were calculated for the 6 mm and 30 mm silicon stiffeners, and for 30 mm diamond and tungsten stiffeners, with thicknesses varying from 30-80 μm. Increasing the thickness of the material by 10 μm, 20 μm and 30 μm improved the P cr by 2.4, 4.7 and 8.2 times, respectively, independent of the material, and substituting diamond for silicon multiplied the buckling capacity by 5.0 times. Stiffeners made of silicon for large animal probe insertion are not strong enough to withstand buckling upon insertion without a significant increase in thickness. Replacing silicon with diamond and increasing the thickness of the stiffener to 50 μm would afford a stiffener with the same P cr capacity as the 6 mm silicon stiffener that had a 100 percent insertion success rate. Experiments should continue with diamond to determine a minimum thickness that will ensure successful insertions and provide an adequate margin of safety.« less

Objective evaluation of insert material for diabetic and athletic footwear.

PubMed

Brodsky, J W; Kourosh, S; Stills, M; Mooney, V

1988-12-01

Five of the most commonly used materials for shoe inserts (soft Plastazote, medium Pelite, PPT, Spenco, and Sorbothane) were objectively evaluated in the laboratory to characterize their behavior in the following three specific functions that correspond to clinical use: (1) the effect on the materials of repeated compression. (2) the effect of a combination of repetitive shear and compression. (3) the force-distribution (force-attenuation) properties of these materials, both when new and after repeated compression. The last function represents a model for relief of pressure beneath plantar bony prominences, a topic of special concern for the insensitive foot. All materials were effective in reducing transmitted force over the simulated bony prominence with a rank order of effectiveness. Other factors considered were: amount and rate of permanent deformation offset by considerations of enhanced moldability when comparing the neoprene and urethane materials with the polyethylene foams. The ideal insert represents a combination of material to achieve both durability and moldability.

Apparatus for establishing flow of a fluid mass having a known velocity

NASA Technical Reports Server (NTRS)

Price, P.; Veikins, O.; Bate, E. R., Jr.; Jones, R. H. (Inventor)

1974-01-01

An apparatus for establishing a flow of fluid mass, such as gas, having a known velocity is introduced. The apparatus is characterized by an hermetically sealed chamber conforming to a closed-loop configuration and including a throat and a plurality of axially displaceable pistons for sweeping through the throat a stream of gas including a core and an unsheared boundary layer. Within the throat there is a cylindrical coring body concentrically related to the throat for receiving the core, and a chamber surrounding the cylindrical body for drawing off the boundary layer, whereby the velocity of the core is liberated from the effects of the velocity of the boundary layer.

[Development of throat clearing herbal teas].

PubMed

Puodziūniene, Gene; Janulis, Valdimaras; Milasius, Arvydas; Budnikas, Milasius

2004-01-01

Medicinal herbs in tea for throat clearing are used from ancient times. Taking into consideration the bronchial mucus secretion stimulating and antispasmodic, antimicrobial, antiphlogistic and stimulating effect on the ciliated epithelium two new formulations of throat clearing herbal tea were originated. The first formulation consists of liquorice roots, sweet fennel and thyme, and the second one consists of pine gemmae, thyme and elder flowers. The methods for identification and assay of the active substances of the components were adapted. The purity of the mixtures was regulated by the limitation of the loss on drying, total ash, microbial contamination, contamination with radionuclides, heavy metals, pesticides and foreign matter. Expiry date of both throat clearing herbal teas was confirmed to be 2 years.

Analytical study of striated nozzle flow with small radius of curvature ratio throats

NASA Technical Reports Server (NTRS)

Norton, D. J.; White, R. E.

1972-01-01

An analytical method was developed which is capable of estimating the chamber and throat conditions in a nozzle with a low radius of curvature throat. The method was programmed using standard FORTRAN 4 language and includes chemical equilibrium calculation subprograms (modified NASA Lewis program CEC71) as an integral part. The method determines detailed and gross rocket characteristics in the presence of striated flows and gives detailed results for the motor chamber and throat plane with as many as 20 discrete zones. The method employs a simultaneous solution of the mass, momentum, and energy equations and allows propellant types, 0/F ratios, propellant distribution, nozzle geometry, and injection schemes to be varied so to predict spatial velocity, density, pressure, and other thermodynamic variable distributions in the chamber as well as the throat. Results for small radius of curvature have shown good comparison to experimental results. Both gaseous and liquid injection may be considered with frozen or equilibrium flow calculations.

Genetic Diversity among Group A Streptococcus Isolated from Throats of Healthy and Symptomatic Children.

PubMed

Chauhan, Smriti; Kashyap, Nitin; Kanga, Anil; Thakur, Kamlesh; Sood, Anuradha; Chandel, Lata

2016-04-01

Group A streptococcus (GAS) is the commonest bacterial cause of pharyngitis. Children in the age group of 5-15 years are most commonly affected. It can also colonize throats of healthy children in this age group. Both cases and carriers can transmit it in the community. Throat swab samples were collected from 1849 asymptomatic and 371 symptomatic children. The rate of isolation of GAS was 1.41% among the asymptomatic group and 7.55% among the symptomatic group. Nine different emm types were encountered in the asymptomatic children and 14 among the symptomatic children. Throat swab cultures must be used in all cases of pharyngitis. Early and appropriate antibiotic therapy will prevent complications. Asymptomatic throat carriage of GAS in children was low in our study. However, they can still act as reservoirs. Emm typing helps in understanding epidemiology and finding new types. © The Author [2016]. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The Application of Coconut Fiber as Dissipative Silencer

NASA Astrophysics Data System (ADS)

Madlan, M. A.; Ghazali, M. I.; Zaman, I.; Kasron, M. Z.; Ying, T. C.

2017-01-01

Heat ventilation air conditioning system (HVAC) is one of the ducting systems that broadly applied in the building. There are HVAC silencers in the market, however the sound absorptive material commonly used is mineral wool. In this research study, a sound absorptive material made of coconut fiber was tested to identify its performance as a potential replacement of green material for ducting silencer. The experiment was carried out in a testing apparatus that follows the BS EN ISO 11691:2009 standard. Different configurations of sound absorptive material and contents of coconut fiber were investigated in the study. The trend of insertion loss at 1/3 octave frequency was identified where at frequency below 3000Hz, the insertion loss of dissipative silencer is observed high at certain frequency with a very narrow range. At 3000Hz, the insertion loss of 4dB to 6dB is constant until 4000Hz and drops until 5000Hz before it increases again steadily up to 13dB at 10000Hz. A similar trend was observed for different configuration of sound absorptive material. Despite the configuration different, the outcome shows that the insertion loss is increasing with higher content of coconut fiber.

Load beam unit replaceable inserts for dry coal extrusion pumps

DOEpatents

Saunders, Timothy; Brady, John D.

2012-11-13

A track assembly for a particulate material extrusion pump according to an exemplary aspect of the present disclosure includes a link assembly with a roller bearing. An insert mounted to a load beam located such that the roller bearing contacts the insert.

Additive Manufacturing for Highly Efficient Window Inserts CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roschli, Alex C.; Chesser, Phillip C.; Love, Lonnie J.

ORNL partnered with the Mackinac Technology Company to demonstrate how additive manufacturing can be used to create highly energy efficient window inserts for retrofit in pre-existing buildings. Many early iterations of the window inserts were fabricated using carbon fiber reinforced thermoplastics and polycarbonate films as a stand in for the low-e coated films produced by the Mackinac Technology Company. After demonstration of the proof of concept, i.e. custom window inserts with tensioned film, the materials used for the manufacture of the frames was more closely examined. Hollow particle-filled syntactic foam and low-density polymer composites formed by expandable microspheres were exploredmore » as the materials used to additively manufacture the frames of the inserts. It was concluded that low-cost retrofit window inserts in custom sizes could be easily fabricated using large scale additive manufacturing. Furthermore, the syntactic and expanded foams developed and tested satisfy the mechanical performance requirements for the application.« less

Topology optimization of two-dimensional elastic wave barriers

NASA Astrophysics Data System (ADS)

Van hoorickx, C.; Sigmund, O.; Schevenels, M.; Lazarov, B. S.; Lombaert, G.

2016-08-01

Topology optimization is a method that optimally distributes material in a given design domain. In this paper, topology optimization is used to design two-dimensional wave barriers embedded in an elastic halfspace. First, harmonic vibration sources are considered, and stiffened material is inserted into a design domain situated between the source and the receiver to minimize wave transmission. At low frequencies, the stiffened material reflects and guides waves away from the surface. At high frequencies, destructive interference is obtained that leads to high values of the insertion loss. To handle harmonic sources at a frequency in a given range, a uniform reduction of the response over a frequency range is pursued. The minimal insertion loss over the frequency range of interest is maximized. The resulting design contains features at depth leading to a reduction of the insertion loss at the lowest frequencies and features close to the surface leading to a reduction at the highest frequencies. For broadband sources, the average insertion loss in a frequency range is optimized. This leads to designs that especially reduce the response at high frequencies. The designs optimized for the frequency averaged insertion loss are found to be sensitive to geometric imperfections. In order to obtain a robust design, a worst case approach is followed.

Normal Gravity Testing of a Microchannel Phase Separator for In Situ Resource Utilization

NASA Technical Reports Server (NTRS)

TeGrotenhuis, Ward E.; Stenkamp, Victoria S.; McQuillen, John (Technical Monitor)

2001-01-01

A microchannel separator, with 2.7 millimeters as the smallest dimension, was tested, and a pore throat structure captured and removed liquid from a gas-liquid stream. The microchannel device was tested over a of gas and liquid flow rates ranging from 0.0005 up to 0. 14 volume fraction of liquid. Four liquids were tested with air. The biggest factor affecting the throughput is the capacity of liquid flow through the pore throat, which is dictated by permeability, liquid viscosity, flow area, pore throat thickness, and pressure difference across the pore throat. Typically, complete separation of gas and liquid fractions was lost when the liquid flow rate reached about 40 to 60% of the pore throat capacity. However, this could occur over a range of 10 to 90% utilization of pore throat capacity. Breakthrough occurs in the microchannel phase separator at conditions similar to the annular to plug flow transition of two-phase microgravity pipe flow implying that operating in the proper flow regime is crucial. Analysis indicates that the Bond number did not affect performance, supporting the premise that hydrodynamic, interfacial, and capillary forces are more important than gravity. However, the relative importance of gravity is better discerned through testing under reduced gravity conditions.

Robotically Driven CT-guided Needle Insertion: Preliminary Results in Phantom and Animal Experiments.

PubMed

Hiraki, Takao; Kamegawa, Tetsushi; Matsuno, Takayuki; Sakurai, Jun; Kirita, Yasuzo; Matsuura, Ryutaro; Yamaguchi, Takuya; Sasaki, Takanori; Mitsuhashi, Toshiharu; Komaki, Toshiyuki; Masaoka, Yoshihisa; Matsui, Yusuke; Fujiwara, Hiroyasu; Iguchi, Toshihiro; Gobara, Hideo; Kanazawa, Susumu

2017-11-01

Purpose To evaluate the accuracy of the remote-controlled robotic computed tomography (CT)-guided needle insertion in phantom and animal experiments. Materials and Methods In a phantom experiment, 18 robotic and manual insertions each were performed with 19-gauge needles by using CT fluoroscopic guidance for the evaluation of the equivalence of accuracy of insertion between the two groups with a 1.0-mm margin. Needle insertion time, CT fluoroscopy time, and radiation exposure were compared by using the Student t test. The animal experiments were approved by the institutional animal care and use committee. In the animal experiment, five robotic insertions each were attempted toward targets in the liver, kidneys, lungs, and hip muscle of three swine by using 19-gauge or 17-gauge needles and by using conventional CT guidance. The feasibility, safety, and accuracy of robotic insertion were evaluated. Results The mean accuracies of robotic and manual insertion in phantoms were 1.6 and 1.4 mm, respectively. The 95% confidence interval of the mean difference was -0.3 to 0.6 mm. There were no significant differences in needle insertion time, CT fluoroscopy time, or radiation exposure to the phantom between the two methods. Effective dose to the physician during robotic insertion was always 0 μSv, while that during manual insertion was 5.7 μSv on average (P < .001). Robotic insertion was feasible in the animals, with an overall mean accuracy of 3.2 mm and three minor procedure-related complications. Conclusion Robotic insertion exhibited equivalent accuracy as manual insertion in phantoms, without radiation exposure to the physician. It was also found to be accurate in an in vivo procedure in animals. © RSNA, 2017 Online supplemental material is available for this article.

Heat transfer to throat tubes in a square-chambered rocket engine at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Nesbitt, James A.; Brindley, William J.

1989-01-01

A gaseous H2/O2 rocket engine was constructed at the NASA-Lewis to provide a high heat flux source representative of the heat flux to the blades in the high pressure fuel turbopump (HPFTP) during startup of the space shuttle main engines. The high heat flux source was required to evaluate the durability of thermal barrier coatings being investigated for use on these blades. The heat transfer, and specifically, the heat flux to tubes located at the throat of the test rocket engine was evaluated and compared to the heat flux to the blades in the HPFTP during engine startup. Gas temperatures, pressures and heat transfer coefficients in the test rocket engine were measured. Near surface metal temperatures below thin thermal barrier coatings were also measured at various angular orientations around the throat tube to indicate the angular dependence of the heat transfer coefficients. A finite difference model for a throat tube was developed and a thermal analysis was performed using the measured gas temperatures and the derived heat transfer coefficients to predict metal temperatures in the tube. Near surface metal temperatures of an uncoated throat tube were measured at the stagnation point and showed good agreement with temperatures predicted by the thermal model. The maximum heat flux to the throat tube was calculated and compared to that predicted for the leading edge of an HPFTP blade. It is shown that the heat flux to an uncooled throat tube is slightly greater than the heat flux to an HPFTP blade during engine startup.

Community-acquired methicillin-resistant Staphylococcus aureus can persist in the throat.

PubMed

Hamdan-Partida, Aida; González-García, Samuel; de la Rosa García, Estela; Bustos-Martínez, Jaime

2018-06-01

Colonization by Staphylococcus aureus is an important factor in infections caused by this microorganism. Among the colonization niches of staphylococci are the nose, skin, intestinal tract, and, recently, the throat has been given relevance. Infections caused by community-acquired methicillin-resistant Staphylococcus aureus (CA-MRSA) can be fatal. Persistence of S. aureus is an important process in the pathogenesis of this microorganism and must be studied. The aim of this study was to determine the persistence of S. aureus in the throat, and characterized the strains. We studied the persistence of S. aureus for 6 years in the throat of apparently healthy people. The isolated strains from the persistent carriers were characterized through PFGE, spa-typing, SCCmec typing, resistance to methicillin, presence of virulence genes (adhesins and toxins), and the formation of biofilm. We found persistent and intermittent carriers of S. aureus in the throat, with methicillin-sensitive (MSSA), methicillin-resistant (MRSA) strains, and confirmed for the first time that CA-MRSA colonizes this niche. These strains can colonize persistently the throat for four years or more. Typification of strains through PFGE and spa-typing revealed that some carriers present the same strain, whereas others present different strains along the period of persistence. Almost all strains induced a strong biofilm formation. All strains presented adhesin and toxin genes, but no shared genotype was found. We conclude that S. aureus, including CA-MRSA strains, can remain persistently in the throat, finding a wide variability among the persistent strains. Copyright © 2018 Elsevier GmbH. All rights reserved.

A comparative study of the diagnostic methods for Group A streptococcal sore throat in two reference hospitals in Yaounde, Cameroon

PubMed Central

Gonsu, Hortense Kamga; Bomki, Cynthia Mbimenyuy; Djomou, François; Toukam, Michel; Ndze, Valantine Ngum; Lyonga, Emilia Enjema; Mbakop, Calixte Didier; Koulla-Shiro, Sinata

2015-01-01

Introduction Sore throat is a common complaint in general practice which is more frequent in children. The most frequent pathogenic bacteria associated with this infection is Streptococcus pyogenes. Rapid Antigen Diagnostic Test (RADT) facilitates the rapid identification and consequently prompt treatment of patients, prevents complications, and also reduces the risk of spread of Group A Streptococcus (GAS). The main objective of this study was to assess the diagnostic value of a rapid streptococcal antigen detection test in patients with sore throat. Methods A cross-sectional descriptive study was carried out from January to April 2011 on patients aged 3 to 72 years consulting for pharyngitis or sore throat at the paediatric and Ear, Nose and Throat units of the University Teaching Hospital Yaounde and the Central Hospital Yaounde. Two throat swabs were collected per patient. One was used for the rapid test and the other for standard bacteriological analysis. Results The prevalence of GAS in the study population was 22.5%. Out of the 71 samples collected, the RADT detected group A streptococcal antigens in 12 of 16 positive cultures giving a sensitivity of 75%. The specificity of the rapid test was 96%, with positive predictive value of 85.7%, and negative predictive value of 93% respectively. Conclusion Rapid test may have an additional value in the management of patients with high risk of having GAS infection. However, tests with a higher sensitivity are needed for accurate and reliable results for early diagnosis of patients with sore throat caused by GAS. PMID:27386017

A comparative study of the diagnostic methods for Group A streptococcal sore throat in two reference hospitals in Yaounde, Cameroon.

PubMed

Gonsu, Hortense Kamga; Bomki, Cynthia Mbimenyuy; Djomou, François; Toukam, Michel; Ndze, Valantine Ngum; Lyonga, Emilia Enjema; Mbakop, Calixte Didier; Koulla-Shiro, Sinata

2015-01-01

Sore throat is a common complaint in general practice which is more frequent in children. The most frequent pathogenic bacteria associated with this infection is Streptococcus pyogenes. Rapid Antigen Diagnostic Test (RADT) facilitates the rapid identification and consequently prompt treatment of patients, prevents complications, and also reduces the risk of spread of Group A Streptococcus (GAS). The main objective of this study was to assess the diagnostic value of a rapid streptococcal antigen detection test in patients with sore throat. A cross-sectional descriptive study was carried out from January to April 2011 on patients aged 3 to 72 years consulting for pharyngitis or sore throat at the paediatric and Ear, Nose and Throat units of the University Teaching Hospital Yaounde and the Central Hospital Yaounde. Two throat swabs were collected per patient. One was used for the rapid test and the other for standard bacteriological analysis. The prevalence of GAS in the study population was 22.5%. Out of the 71 samples collected, the RADT detected group A streptococcal antigens in 12 of 16 positive cultures giving a sensitivity of 75%. The specificity of the rapid test was 96%, with positive predictive value of 85.7%, and negative predictive value of 93% respectively. Rapid test may have an additional value in the management of patients with high risk of having GAS infection. However, tests with a higher sensitivity are needed for accurate and reliable results for early diagnosis of patients with sore throat caused by GAS.

Protocol for north of England and Scotland study of tonsillectomy and adeno-tonsillectomy in children (NESSTAC). A pragmatic randomised controlled trial comparing surgical intervention with conventional medical treatment in children with recurrent sore throats

PubMed Central

Bond, John; Wilson, Janet; Eccles, Martin; Vanoli, Alessandra; Steen, Nick; Clarke, Ray; Zarod, Andrew; Lock, Catherine; Brittain, Katie; Speed, Chris; Rousseau, Nikki

2006-01-01

Background Uncertainties surrounding the effectiveness and cost-effectiveness of childhood tonsillectomy for recurrent sore throat led the NHS Health Technology Assessment Programme to commission this research to evaluate the effectiveness and cost-effectiveness of tonsillectomy and adeno-tonsillectomy in comparison with standard non-surgical management in children aged under 16 with recurrent throat infections. The aim is to evaluate if tonsillectomy and adeno-tonsillectomy reduces the number of episodes of sore throats among children to a clinically significant extent. Methods/design A simple prospective pragmatic randomised controlled trial with economic analysis and prospective cohort study of non-trial participants comparing surgical intervention with conventional medical treatment. The treatment arm will receive tonsillectomy and adeno-tonsillectomy while in the control arm non-surgical conventional medical treatment only will be used. The primary outcome measure will be reported number of episodes of sore throat over two years with secondary outcomes measures of reported number of episodes of sore throat, otitis media and upper respiratory tract infection which invoke a GP consultation; reported number of symptom-free days; reported severity of sore throats and surgical and anaesthetic morbidity. The study will take place in five hospitals in the UK. The trial population will be 406 children aged 4–15 on their last birthday with recurrent sore throat referred by primary care to the 5 otolaryngology departments. The duration of the study is seven years (July 2001- July 2008). Discussion As with all pragmatic randomised controlled trials it is impossible to control the external environment in which the research is taking place. Since this trial began a number of factors have arisen which could affect the outcome including; a reduction in the incidence of respiratory tract infections, marked socio-economic differences in consultation rates, the results from the National Prospective Tonsillectomy Audit and the Government's waiting list initiatives. PMID:16899123

Protocol for north of England and Scotland study of tonsillectomy and adeno-tonsillectomy in children (NESSTAC). A pragmatic randomised controlled trial comparing surgical intervention with conventional medical treatment in children with recurrent sore throats.

PubMed

Bond, John; Wilson, Janet; Eccles, Martin; Vanoli, Alessandra; Steen, Nick; Clarke, Ray; Zarod, Andrew; Lock, Catherine; Brittain, Katie; Speed, Chris; Rousseau, Nikki

2006-08-09

Uncertainties surrounding the effectiveness and cost-effectiveness of childhood tonsillectomy for recurrent sore throat led the NHS Health Technology Assessment Programme to commission this research to evaluate the effectiveness and cost-effectiveness of tonsillectomy and adeno-tonsillectomy in comparison with standard non-surgical management in children aged under 16 with recurrent throat infections. The aim is to evaluate if tonsillectomy and adeno-tonsillectomy reduces the number of episodes of sore throats among children to a clinically significant extent. A simple prospective pragmatic randomised controlled trial with economic analysis and prospective cohort study of non-trial participants comparing surgical intervention with conventional medical treatment. The treatment arm will receive tonsillectomy and adeno-tonsillectomy while in the control arm non-surgical conventional medical treatment only will be used. The primary outcome measure will be reported number of episodes of sore throat over two years with secondary outcomes measures of reported number of episodes of sore throat, otitis media and upper respiratory tract infection which invoke a GP consultation; reported number of symptom-free days; reported severity of sore throats and surgical and anaesthetic morbidity. The study will take place in five hospitals in the UK. The trial population will be 406 children aged 4-15 on their last birthday with recurrent sore throat referred by primary care to the 5 otolaryngology departments. The duration of the study is seven years (July 2001-July 2008). As with all pragmatic randomised controlled trials it is impossible to control the external environment in which the research is taking place. Since this trial began a number of factors have arisen which could affect the outcome including; a reduction in the incidence of respiratory tract infections, marked socio-economic differences in consultation rates, the results from the National Prospective Tonsillectomy Audit and the Government's waiting list initiatives.

Sore throat: effective communication delivers improved diagnosis, enhanced self-care and more rational use of antibiotics.

PubMed

van der Velden, A W; Bell, J; Sessa, A; Duerden, M; Altiner, A

2013-11-01

The majority of throat infections are of viral origin and resolve without antibiotic treatment. Despite this, antibiotic use for sore throat infections remains high, partly because it is difficult to determine when antibiotics may be useful, on the basis of physical findings alone. Antibiotics may be beneficial in bacterial throat infections under certain clinical and epidemiological circumstances; however, even many of those infections in which bacteria play a role do resolve just as quickly without antibiotics. Furthermore, non-medical factors such as patient expectations and patient pressure are also important drivers of antibiotic use. To address these issues, a behavioural change is required that can be facilitated by improved communication between primary healthcare providers and patients. In this article, we provide doctors, nurses and pharmacy staff, working in primary care or in the community, with a structured approach to sore throat management, with the aim of educating and empowering patients to self-manage their condition. The first component of this approach involves identifying and addressing patients' expectations and concerns with regard to their sore throat and eliciting their opinion on antibiotics. The second part is dedicated to a pragmatic assessment of the severity of the condition, with attention to red-flag symptoms and risk factors for serious complications. Rather than just focusing on the cause (bacterial or viral) of the upper respiratory tract infections as a rationale for antibiotic use, healthcare providers should instead consider the severity of the patient's condition and whether they are at high risk of complications. The third part involves counselling patients on effective self-management options and providing information on the expected clinical course. Such a structured approach to sore throat management, using empathetic, non-paternalistic language, combined with written patient information, will help to drive patient confidence in self-care and encourage them to accept the self-limiting character of the illness - important steps towards improving antibiotic stewardship in acute throat infections. © 2013 John Wiley & Sons Ltd.

Antibiotics for sore throat.

PubMed

Spinks, Anneliese; Glasziou, Paul P; Del Mar, Chris B

2013-11-05

Sore throat is a common reason for people to present for medical care. Although it remits spontaneously, primary care doctors commonly prescribe antibiotics for it. To assess the benefits of antibiotics for sore throat for patients in primary care settings. We searched CENTRAL 2013, Issue 6, MEDLINE (January 1966 to July week 1, 2013) and EMBASE (January 1990 to July 2013). Randomised controlled trials (RCTs) or quasi-RCTs of antibiotics versus control assessing typical sore throat symptoms or complications. Two review authors independently screened studies for inclusion and extracted data. We resolved differences in opinion by discussion. We contacted trial authors from three studies for additional information. We included 27 trials with 12,835 cases of sore throat. We did not identify any new trials in this 2013 update. 1. Symptoms Throat soreness and fever were reduced by about half by using antibiotics. The greatest difference was seen at day three. The number needed to treat to benefit (NNTB) to prevent one sore throat at day three was less than six; at week one it was 21. 2. Non-suppurative complications The trend was antibiotics protecting against acute glomerulonephritis but there were too few cases to be sure. Several studies found antibiotics reduced acute rheumatic fever by more than two-thirds within one month (risk ratio (RR) 0.27; 95% confidence interval (CI) 0.12 to 0.60). 3. Suppurative complications Antibiotics reduced the incidence of acute otitis media within 14 days (RR 0.30; 95% CI 0.15 to 0.58); acute sinusitis within 14 days (RR 0.48; 95% CI 0.08 to 2.76); and quinsy within two months (RR 0.15; 95% CI 0.05 to 0.47) compared to those taking placebo. 4. Subgroup analyses of symptom reduction Antibiotics were more effective against symptoms at day three (RR 0.58; 95% CI 0.48 to 0.71) if throat swabs were positive for Streptococcus, compared to RR 0.78; 95% CI 0.63 to 0.97 if negative. Similarly at week one the RR was 0.29 (95% CI 0.12 to 0.70) for positive and 0.73 (95% CI 0.50 to 1.07) for negative Streptococcus swabs. Antibiotics confer relative benefits in the treatment of sore throat. However, the absolute benefits are modest. Protecting sore throat sufferers against suppurative and non-suppurative complications in high-income countries requires treating many with antibiotics for one to benefit. This NNTB may be lower in low-income countries. Antibiotics shorten the duration of symptoms by about 16 hours overall.

Laser Journal (Selected Articles),

DTIC Science & Technology

1982-09-10

temperature CO2 branch selection laser with a lifetime already exceeding 6500 hours which may be even longer. HIGH POWER LONG LIFE HeCd LASER Qu Shipu...method of plating single crystal gold film in a vacuum with the foreign material extension method. First mica is used as the substrate. Then a special...Hospital) Chen Zhasping Zhou Yiping et al (Eye, Ear, Nose, Throat Hospital, Examination Department, Shanghai Medical School Number 1.) Qu Zhipu et al

Neck dissection

MedlinePlus

... cancer - neck dissection; Throat cancer - neck dissection; Squamous cell cancer - neck dissection ... blood cells around the body to fight infection. Cancer cells in the mouth or throat can travel in ...

Rapid Detection of Enveloped Viruses.

DTIC Science & Technology

1988-03-12

analysis of samples with the highest possible virus titer. Specimens were quick-frozen and stored at -700C. Throat washings were also obtained from...are throat washings performed with a veal infusion broth-gelatin mixture (2.5% V.I.B. and 0.5% gelatin in distilled water) and have been stored at -200C...enlisted the cooperation of the Director of Employee Health Services, Dr. Donald Smith, and obtained 14 throat wash specimens from Mount Sinai employees. We

Throat Culture from Patients with Meningococcal Meningitis

DTIC Science & Technology

1990-01-01

THROAT CULTURE FROM PATIENTS-’WITH MENINGOCOCCAL MENINGITIS BY J.E. Sippel and N.I. Girigs U.S. NAVAL MEDICAL RESEARCH UNIT NO. 3 (CAIRO, ARAB REPUBLIC...lowv albumin eoncen rations, characteristically, have a centra fpit and are throat swabs from teenage or young dults but that it als’q underestimites...8217described would’/cletzrly facilitate recognition read at 590 tim against commensal staphylococci and strep - NP IIRENWALD The procedure is linear t thie

Epidemic Outbreak Surveillance (EOS)

DTIC Science & Technology

2006-07-01

Experiment to Test Integrity of2003 Nasal Wash and Throat Swab Samples Stored at -80°C. September 2005 (Sue WorthyLuke Daum) Seven matched pairs of...Nasal Wash and Throat Swab samples, previously tested in September 2004 for Influenza A, were pulled from the -80°C storage freezer for re-testing...January 2006 a detailed vrocess was completed to inventorv and organize the sample storage freezers for all Nasal wash, Throat swab and PAXgene

Experimental and raytrace results for throat-to-throat compound parabolic concentrators

NASA Technical Reports Server (NTRS)

Leviton, D. B.; Leitch, J. W.

1986-01-01

Compound parabolic concentrators are nonimaging cone-shaped optics with useful angular transmission characteristics. Two cones used throat-to-throat accept radiant flux within one well-defined acceptance angle and redistribute it into another. If the entrance cone is fed with Lambertian flux, the exit cone produces a beam whose half-angle is the exit cone's acceptance angle and whose cross section shows uniform irradiance from near the exit mouth to infinity. (The pair is a beam angle transformer). The design of one pair of cones is discussed, also an experiment to map the irradiance of the emergent beam, and a raytracing program which models the cones fed by Lambertian flux. Experimental results compare favorably with raytrace results.

Pharyngitis - viral

MedlinePlus

... throat is due to a viral infection. The antibiotics will not help. Using them to treat viral infections helps bacteria become resistant to antibiotics. With some sore throats (such as those caused ...

Cybermaterials: materials by design and accelerated insertion of materials

NASA Astrophysics Data System (ADS)

Xiong, Wei; Olson, Gregory B.

2016-02-01

Cybermaterials innovation entails an integration of Materials by Design and accelerated insertion of materials (AIM), which transfers studio ideation into industrial manufacturing. By assembling a hierarchical architecture of integrated computational materials design (ICMD) based on materials genomic fundamental databases, the ICMD mechanistic design models accelerate innovation. We here review progress in the development of linkage models of the process-structure-property-performance paradigm, as well as related design accelerating tools. Extending the materials development capability based on phase-level structural control requires more fundamental investment at the level of the Materials Genome, with focus on improving applicable parametric design models and constructing high-quality databases. Future opportunities in materials genomic research serving both Materials by Design and AIM are addressed.

Pore-throat radius and tortuosity estimation from formation resistivity data for tight-gas sandstone reservoirs

NASA Astrophysics Data System (ADS)

Ziarani, Ali S.; Aguilera, Roberto

2012-08-01

A new model is proposed for estimation of pore-throat aperture size from formation resistivity factor and permeability data. The model is validated with data from the Mesaverde sandstone using brine salinities ranging from 20,000 to 200,000 ppm. The data analyzed includes various basins such as Green River, Piceance, Sand Wash, Powder River, Uinta, Washakie and Wind River, available in the literature. For pore-throat radii analysis the methodology involves the use of log-log plots of pore-throat radius versus the product of formation resistivity factor and permeability (rT = a(FK)b + c). The model fits over 280 samples from the Mesaverde formation with coefficients of determination varying between 0.95 and 0.99 depending primarily on the type of model used for pore throat radius calculation. The brine salinity has some minor effects on the results. The model can provide better estimates of pore-throat radii if it is calibrated with experimental techniques such as mercury porosimetry. The results show pore-throat radii varying between 0.001 and 5 μm for the Mesaverde tight sandstone; however, most of the samples fall in a range between 0.01 and 1 μm. For tortuosity analysis, the calculation involves the use of product of formation factor and porosity data. Results indicate that the estimated tortuosity values range mainly between 1 and 5. For samples with lower porosities (< 5%), tortuosity values show a wider scatter (between 1 and 8); whereas for samples with larger porosities (> 15%), the scattering in tortuosity decreases significantly. In general, for tortuosity calculation in tight gas sandstone formations, a square root model with a parameter (bf) representing various types of connecting pores, i.e., sheet-like and tubular pores, is recommended.

Comparison of Laryngeal Mask Airway Supreme and Laryngeal Mask Airway Proseal with respect to oropharyngeal leak pressure during laparoscopic cholecystectomy: a randomised controlled trial.

PubMed

Beleña, José M; Núñez, Mónica; Anta, Diego; Carnero, Maria; Gracia, José L; Ayala, José L; Alvarez, Raquel; Yuste, Javier

2013-03-01

A comparison of the efficacy and safety of the Laryngeal Mask Airway (LMA) Supreme (LMAS) versus the LMA Proseal (LMAP) in elective laparoscopic cholecystectomy. To compare the LMAS with LMAP in terms of ventilatory efficacy, airway leak pressure (airway protection), ease-of-use and complications. Prospective, single-blind, randomised, controlled study. The Hospital del Sureste and Hospital Ramon y Cajal, Madrid, between May 2009 and March 2011. The Hospital del Sureste is a secondary hospital and Hospital Ramon y Cajal is a tertiary hospital. Patients undergoing elective laparoscopic cholecystectomy were studied following informed consent. Inclusion criteria were American Society of Anesthesiologists physical status I to III and age 18 or more. Exclusion criteria were BMI more than 40 kg m, symptomatic hiatus hernia or severe gastro-oesophageal reflux. Anaesthesiologists experienced in the use of LMAP and LMAS participated in the trial. One hundred twenty-two patients were randomly allocated to LMAS or LMAP. Our primary outcome measure was the oropharyngeal leak pressure (OLP). Secondary outcomes were the time and number of attempts for insertion, ease of insertion of the drain tube, adequacy of ventilation and the incidence of complication. Patients were interviewed postoperatively to evaluate the presence of sore throat, dysphagia or dysphonia. Two patients were excluded when surgery changed from laparoscopic to open. A total of 120 patients were finally included in the analysis. The mean OLP in the LMAP group was significantly higher than that in the LMAS group (30.7 ± 6.2 versus 26.8 ± 4.1 cmH2O;P < 0.01). This was consistent with a higher maximum tidal volume achieved with the LMAP compared to the LMAS (511 ± 68 versus 475 ± 55 ml; P = 0.04). The success rate of the first attempt insertion was higher for the LMAS group than the LMAP group (96.7 and 71.2%, respectively; P < 0.01). The time taken for insertion, ease of insertion of the drain tube, complications and postoperative pharyngolaryngeal adverse events were similar in both groups. The LMAP has a higher OLP and achieves a higher maximum tidal volume compared to the LMAS, in patients undergoing elective laparoscopic cholecystectomy. The success of the first attempt insertion was higher for the LMAS.

Comparison of illumigene Group A Streptococcus Assay with Culture of Throat Swabs from Children with Sore Throats in the New Zealand School-Based Rheumatic Fever Prevention Program.

PubMed

Upton, Arlo; Bissessor, Liselle; Farrell, Elizabeth; Shulman, Stanford T; Zheng, Xiaotian; Lennon, Diana

2016-01-01

Group A streptococcal (GAS) pharyngitis is a particularly important condition in areas of New Zealand where the incidence of acute rheumatic fever remains unacceptably high. Prompt diagnosis and treatment of GAS pharyngitis are cornerstones of the Rheumatic Fever Prevention Programme, but these are hindered by the turnaround time of culture. Tests with excellent performance and rapid turnaround times are needed. For this study, throat swabs (Copan ESwabs) were collected from schoolchildren self-identifying with a sore throat. Samples were tested by routine culture and the illumigene GAS assay using loop-mediated isothermal amplification. Discrepant results were resolved by retesting of the same specimen by an alternative molecular assay. Seven hundred fifty-seven throat swab specimens were tested by both methods. The performance characteristics of the illumigene assay using culture on blood agar as the "gold standard" and following discrepancy analysis were as follows: sensitivity, 82% and 87%, respectively; specificity, 93% and 98%, respectively; positive predictive value, 61% and 88%, respectively; and negative predictive value, 97% and 97%, respectively. In our unique setting of a school-based throat swabbing program, the illumigene assay did not perform quite as well as described in previous reports. Despite this, its improved sensitivity and rapid turnaround time compared with those of culture are appealing. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Impact of an Exhaust Throat on Semi-Idealized Rotating Detonation Engine Performance

NASA Technical Reports Server (NTRS)

Paxson, Daniel E.

2016-01-01

A computational fluid dynamic (CFD) model of a rotating detonation engine (RDE) is used to examine the impact of an exhaust throat (i.e. a constriction) on performance. The model simulates an RDE which is premixed, adiabatic, inviscid, and which contains an inlet valve that prevents backflow from the high pressure region directly behind the rotating detonation. Performance is assessed in terms of ideal net specific impulse which is computed on the assumption of lossless expansion of the working fluid to the ambient pressure through a notional diverging nozzle section downstream of the throat. Such a semi-idealized analysis, while not real-world, allows the effect of the throat to be examined in isolation from, rather than coupled to (as it actually is) various loss mechanisms. For the single Mach 1.4 flight condition considered, it is found that the addition of a throat can yield a 9.4 percent increase in specific impulse. However, it is also found that when the exit throat restriction gets too small, an unstable type of operation ensues which eventually leads to the detonation failing. This behavior is found to be somewhat mitigated by the addition of an RDE inlet restriction across which there is an aerodynamic loss. Remarkably, this loss is overcome by the benefits of the further exhaust restrictions allowed. The end result is a configuration with a 10.3 percent improvement in ideal net specific thrust.

Impact of an Exhaust Throat on Semi-Idealized Rotating Detonation Engine Performance

NASA Technical Reports Server (NTRS)

Paxson, Daniel E.

2016-01-01

A computational fluid dynamic (CFD) model of a rotating detonation engine (RDE) is used to examine the impact of an exhaust throat (i.e., a constriction) on performance. The model simulates an RDE which is premixed, adiabatic, inviscid, and which contains an inlet valve that prevents backflow from the high pressure region directly behind the rotating detonation. Performance is assessed in terms of ideal net specific impulse which is computed on the assumption of lossless expansion of the working fluid to the ambient pressure through a notional diverging nozzle section downstream of the throat. Such a semi-idealized analysis, while not real-world, allows the effect of the throat to be examined in isolation from, rather than coupled to (as it actually is) various loss mechanisms. For the single Mach 1.4 flight condition considered, it is found that the addition of a throat can yield a 9.4 percent increase in specific impulse. However, it is also found that when the exit throat restriction gets too small, an unstable type of operation ensues which eventually leads to the detonation failing. This behavior is found to be somewhat mitigated by the addition of an RDE inlet restriction across which there is an aerodynamic loss. Remarkably, this loss is overcome by the benefits of the further exhaust restrictions allowed. The end result is a configuration with a 10.3 percent improvement in ideal net specific thrust.

Vocal Tract Discomfort and Risk Factors in University Teachers.

PubMed

Korn, Gustavo Polacow; Augusto de Lima Pontes, Antonio; Abranches, Denise; Augusto de Lima Pontes, Paulo

2016-07-01

To characterize the presence of and risk factors for throat pain or irritation among male and female university teachers in private institutions within the city of São Paulo. This is a cross-sectional survey. Voice self-evaluation forms prepared by the Brazilian Ministry of Labor were administered to 846 university teachers in a private institution in the city of São Paulo, Brazil. The prevalence of throat pain or irritation was 50.8% and was higher in the women (62.7%) than in the men (43.5%). The prevalence of throat pain or irritation was higher among professionals ≤60 years old and among those who spent most of their time teaching compared with those who spent most of their time performing other professional activities. Other factors, such as noise and sound competition, air pollution, stress and anxiety, personal habits, and lifestyle/quality of life, were related to the presence of throat pain or irritation. University teachers demonstrated a high prevalence of throat pain or irritation. Factors such as age ≤60 years, female gender, time-consuming professional activities, noise and sound competition in the work environment, stress and anxiety, air pollution, access to water, personal habits, and lifestyle/quality of life were related to the presence of throat pain or irritation. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Osteochondrodysplasias

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Osteopetroses

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Relationship between footwear comfort of shoe inserts and anthropometric and sensory factors.

PubMed

Mündermann, A; Stefanyshyn, D J; Nigg, B M

2001-11-01

The purposes of this study were (a) to determine lower extremity anthropometric and sensory factors that are related to differences in comfort perception of shoe inserts with varying shape and material and (b) to investigate whether shoe inserts that improve comfort decrease injury frequency in a military population. 206 military personnel volunteered for this study. The shoe inserts varied in arch and heel cup shape, hardness, and elasticity in the heel and forefoot regions. A no insert condition was included as the control condition. Measured subject characteristics included foot shape, foot and leg alignment, and tactile and vibration sensitivity of the plantar surface of the foot. Footwear comfort was assessed using a visual analog scale. Injury frequency was evaluated with a questionnaire. The statistical analyses included Student's t-tests for repeated measures, ANOVA (within subjects), MANOVA (within insert combinations), and chi-square tests. The average comfort ratings for all shoe inserts were significantly higher than the average comfort rating for the control condition. The incidence of stress fractures and pain at different locations was reduced by 1.5-13.4% for the insert compared with the control group. Foot arch height, foot and leg alignment, and foot sensitivity were significantly related to differences in comfort ratings for the hard/soft, the viscous/elastic, and the high arch/low arch insert combinations. Shoe inserts of different shape and material that are comfortable are able to decrease injury frequency. The results of this study showed that subject specific characteristics influence comfort perception of shoe inserts.

Simulation of a supersonic flow around a body with a frontal gas-permeable insert by using a skeleton model of a highly porous cellular material

NASA Astrophysics Data System (ADS)

Poplavskaya, T. V.; Kirilovskiy, S. V.; Mironov, S. G.

2017-10-01

Numerical simulation of supersonic flow past a cylinder with a frontal gas-permeable insert is performed using the skeleton model of a highly porous cellular material. Numerical simulation was carried out within the framework of two-dimensional RANS equations written in an axisymmetric form. The skeleton model is a system of coaxial rings of different diameters, arranged in staggered order. The calculations were carried out in a wide range of determining parameters: Mach numbers M∞ = 3, 4.85 and 7, unit Reynolds numbers Re1∞ = 13.8×105 ÷ 13.8×106 m-1, the cylinder diameter 6÷40mm, the length of the porous insert 3÷45mm, the cell diameter of 1 and 3 mm. The results of the calculations are consistent with the available experimental data. The applicability of the skeleton model for the description of supersonic flow around axisymmetric bodies with front inserts from cellular-porous materials is shown.

An algorithm for a selective use of throat swabs in the diagnosis of group A streptococcal pharyngo-tonsillitis in general practice.

PubMed

Hoffmann, S

1992-12-01

A prospective evaluation was made of an algorithm for a selective use of throat swabs in patients with sore throat in general practice. The algorithm states that a throat swab should be obtained (a) in all children younger than 15 years; (b) in patients aged 15 years or more who have pain on swallowing and at least three of four signs (enlarged or hyperaemic tonsils; exudate; enlarged or tender angular lymph nodes; and a temperature > or = 38 degrees C); and (c) in adults aged 15-44 years with pain on swallowing and one or two of the four signs, but not both cough and coryza. Group A streptococci were found by laboratory culture in 30% of throat swabs from 1783 patients. Using these results as the reference, the algorithm was 95% sensitive and 26% specific, and assigned 80% of the patients to be swabbed. Its positive and negative predictive values in this setting were 36% and 92%, respectively. It is concluded that this algorithm may be useful in general practice.

Female Preference for Sympatric vs. Allopatric Male Throat Color Morphs in the Mesquite Lizard (Sceloporus grammicus) Species Complex

PubMed Central

Bastiaans, Elizabeth; Bastiaans, Mary Jane; Morinaga, Gen; Castañeda Gaytán, José Gamaliel; Marshall, Jonathon C.; Bane, Brendan; de la Cruz, Fausto Méndez; Sinervo, Barry

2014-01-01

Color polymorphic sexual signals are often associated with alternative reproductive behaviors within populations, and the number, frequency, or type of morphs present often vary among populations. When these differences lead to assortative mating by population, the study of such polymorphic taxa may shed light on speciation mechanisms. We studied two populations of a lizard with polymorphic throat color, an important sexual signal. Males in one population exhibit orange, yellow, or blue throats; whereas males in the other exhibit orange, yellow, or white throats. We assessed female behavior when choosing between allopatric and sympatric males. We asked whether females discriminated more when the allopatric male was of an unfamiliar morph than when the allopatric male was similar in coloration to the sympatric male. We found that female rejection of allopatric males relative to sympatric males was more pronounced when males in a pair were more different in throat color. Our findings may help illuminate how behavioral responses to color morph differences between populations with polymorphic sexual signals contribute to reproductive isolation. PMID:24718297

Reactor pressure vessel nozzle

DOEpatents

Challberg, Roy C.; Upton, Hubert A.

1994-01-01

A nozzle for joining a pool of water to a nuclear reactor pressure vessel includes a tubular body having a proximal end joinable to the pressure vessel and a distal end joinable in flow communication with the pool. The body includes a flow passage therethrough having in serial flow communication a first port at the distal end, a throat spaced axially from the first port, a conical channel extending axially from the throat, and a second port at the proximal end which is joinable in flow communication with the pressure vessel. The inner diameter of the flow passage decreases from the first port to the throat and then increases along the conical channel to the second port. In this way, the conical channel acts as a diverging channel or diffuser in the forward flow direction from the first port to the second port for recovering pressure due to the flow restriction provided by the throat. In the backflow direction from the second port to the first port, the conical channel is a converging channel and with the abrupt increase in flow area from the throat to the first port collectively increase resistance to flow therethrough.

Experimental study of moving throat plug in a shock tunnel

NASA Astrophysics Data System (ADS)

Lee, J. K.; Park, C.; Kwon, O. J.

2015-07-01

An experimental study has been carried out to investigate the flow in the KAIST shock tunnel with two moving throat plugs at a primary shock velocity of 1.19 km/s. The nozzle reservoir pressure and the Pitot pressure at the exit of the nozzle were measured to examine the influence of the moving throat plugs on the shock tunnel flow. To assess the present experimental results, comparisons with previous work using a stationary throat plug were made. The mechanism for closing the moving throat plug was developed and verified. The source of the force to move the plug was the pressure generated when the primary shock was reflected at the bottom of the plug. It was observed that the two plugs terminated the shock tunnel flow after the steady flow. .The time for the plugs to terminate the flow showed good agreement with the calculation of the proposed simple analytic solution. There was a negligible difference in flow values such as the reflected pressure and the Pitot pressure between the moving and the stationary plugs.

Solid Propellant Test Article (SPTA) Test Stand

NASA Technical Reports Server (NTRS)

1991-01-01

This photograph shows the Solid Propellant Test Article (SPTA) test stand with the Modified Nasa Motor (M-NASA) test article at the Marshall Space Flight Center (MSFC). The SPTA test stand, 12-feet wide by 12-feet long by 24-feet high, was built in 1989 to provide comparative performance data on nozzle and case insulation material and to verify thermostructural analysis models. A modified NASA 48-inch solid motor (M-NASA motor) with a 12-foot blast tube and 10-inch throat makes up the SPTA. The M-NASA motor is being used to evaluate solid rocket motor internal non-asbestos insulation materials, nozzle designs, materials, and new inspection techniques. New internal motor case instrumentation techniques are also being evaluated.

Refractory electrodes for joule heating and methods of using same

DOEpatents

Lamar, D.A.; Chapman, C.C.; Elliott, M.L.

1998-05-12

A certain group of electrically conductive refractory materials presently known for use in high temperature applications as throat constructions, melter sidewalls, forehearth, stacks, port sills, hot face lining for slagging coal gasifiers, slag runners, and linings for nuclear waste encapsulation furnaces may be used as electrodes permitting joule heating at temperatures in excess of 1,200 C in excess of about 4400 hours even in the presence of transition group element(s). More specifically, the invention is an electrode for melting earthen materials, wherein the electrode is made from an electrically conductive refractory material, specifically at least one metal oxide wherein the metal is selected from the group consisting of chrome, ruthenium, rhodium, tin and combinations thereof. 2 figs.

Evaluation of waveguide coating materials

NASA Technical Reports Server (NTRS)

Chen, W. C. J.; Baker, B. W.

1982-01-01

Waveguide coating materials were tested at 8470 MHz for insertion loss. Samples of these coatings on waveguide pieces without flanges were tested in an environmental chamber to simulate the effects of high power microwave heating. Test results indicated that three types of coating materials are acceptable with regard to insertion loss. However, simulated microwave heating caused debonding of Metcot 7 and BD-991 coatings, resulting in peelings in the waveguide. The higher cost Chemglaze R104 does not exhibit this problem.

Congestive Hepatomegaly

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Cutis Laxa

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Bacterial Tracheitis

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Transpiration cooled throat for hydrocarbon rocket engines

NASA Technical Reports Server (NTRS)

May, Lee R.; Burkhardt, Wendel M.

1991-01-01

The objective for the Transpiration Cooled Throat for Hydrocarbon Rocket Engines Program was to characterize the use of hydrocarbon fuels as transpiration coolants for rocket nozzle throats. The hydrocarbon fuels investigated in this program were RP-1 and methane. To adequately characterize the above transpiration coolants, a program was planned which would (1) predict engine system performance and life enhancements due to transpiration cooling of the throat region using analytical models, anchored with available data; (2) a versatile transpiration cooled subscale rocket thrust chamber was designed and fabricated; (3) the subscale thrust chamber was tested over a limited range of conditions, e.g., coolant type, chamber pressure, transpiration cooled length, and coolant flow rate; and (4) detailed data analyses were conducted to determine the relationship between the key performance and life enhancement variables.

An orthodontic bracket embedded in the medial pterygoid surface: a case report.

PubMed

Wilmott, Sheryl E; Ikeagwuani, Okechukwu; McLeod, Niall M H

2016-01-08

There is a potential risk that orthodontic brackets can become dislodged into the aerodigestive tract. This case illustrates the management of an orthodontic bracket, which became embedded in the deep tissues of the oropharynx. We aim to highlight the potential risk misplaced dental instruments and materials pose, including that they may become embedded in the soft tissues of the throat and suggest that that this possibility should be considered when they cannot be localized.

An orthodontic bracket embedded in the medial pterygoid surface: a case report.

PubMed

Wilmott, Sheryl E; Ikeagwuani, Okechukwu; McLeod, Niall M H

2016-03-01

There is a potential risk that orthodontic brackets can become dislodged into the aerodigestive tract. This case illustrates the management of an orthodontic bracket, which became embedded in the deep tissues of the oropharynx. We aim to highlight the potential risk misplaced dental instruments and materials pose, including that they may become embedded in the soft tissues of the throat and suggest that that this possibility should be considered when they cannot be localized.

A life history study of the yellow throat

USGS Publications Warehouse

Stewart, R.E.

1953-01-01

Investigations concerning the life history of the Yellow-throat were made in southern Michigan during the spring and summer of 1938. Supplementary information was also obtained at Arlington, Virginia, in 1940 and at the Patuxent Research Refuge, Maryland, in 1947.....Resident males established territories almost immediately upon arrival in spring. In southern Michigan some resident males arrived at least as soon as, if not before, transient males. Most females appeared on their nesting ground about a week later. Adults were engaged in nesting activities from the time of their arrival in spring until the advent of the post-nuptial molt in late summer.....Typical Yellow-throat habitat consists of a mixture of a dense herbaceous vegetation and small woody plants in damp or wet situations. At Ann Arbor, the Yellow-throat was a common breeding species in its restricted suitable habitat. The population density in one area of suitable habitat was about 69 territorial males per 100 acres. Of 11 territorial males that were intensively studied, one was polygamous (with two mates), nine were monogamous, and one was probably monogamous (with at least one mate).....The song of the individual Yellow-throat was heard throughout the breeding season except for the courtship period. Two major types of song were the common song given while perched, and an occasional, more elaborate, flight song. Most males sing in spurts, singing at fairly regular intervals for a considerable period and then abruptly ceasing for another period. The vocabulary of both sexes included several types of call notes that appeared either to have special functions or to represent outward expressions of distinct emotional states of the bird.....Resident males were antagonistic toward each other throughout the breeding season. Most remained on well-established territories during this period. Territories of 10 monogamous males ranged in size from .8 to 1.8 acres but the territory of one polygamous male occupied. 3.4 acres. The behavior of males during inter-territorial encounters was similar in some respects to their behavior when courting females.....While courting females, the males are very attentive and seldom sing for about one week. During the courtship period the female locates the nesting site and builds the nest without assistance from the male.....Nests, constructed of dried plant materials, were situated on or near the ground and were supported on all sides by stems of herbaceous plants or limbs of shrubs. Many nests were composed of three layers with the coarser materials being used in the outer layer.....The full clutch of eggs in 12 nests ranged from 4 to 6 (average, 4.6). Early clutches seem to be larger than later ones. After the first egg is laid, one is laid on each succeeding day until the clutch is complete. Incubation period is about 12 days. Incubation is only by the female. Records of daytime incubation schedules of three females about half way through incubation indicate that the periods spent on and off the nests average about 61 and 16 minutes, respectively.....Young Yellow-throats usually remain in the nest for eight or nine days. During this period they grow and develop rapidly. Their weight quintuples in six days. Both sexes are active in feeding the young and in removing excreta from the nest. Records of feeding at three nests showed a range of one feeding per 5 1/2 minutes to one feeding per 22 minutes, the rate increasing with age of young. Adults care for the young for at least two weeks after the young leave the nest.....Ten of 12 females that were intensively studied were successful in raising young beyond the nestling stage. Only one of these raised two broods, although three females built at least three nests each. In 19 nests, 11 (58 per cent) produced nestlings and 7 (37 per cent) produced fledglings. In total, the 19 nests produced an average of one fledgling Yellow-throat per nest. Of 22 nests that were found near Ann Arbor, 10 (45

Method of fabricating a honeycomb structure

DOEpatents

Holleran, Louis M.; Lipp, G. Daniel

1999-01-01

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb.

Method of fabricating a honeycomb structure

DOEpatents

Holleran, L.M.; Lipp, G.D.

1999-08-03

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb. 7 figs.

Tonsillitis

MedlinePlus

... A bacterial or viral infection can cause tonsillitis. Strep throat is a common cause. The infection may also ... days after you start the antibiotics. Children with strep throat should be kept home from school or day ...

Biological Resources Survey of Mountain Springs Canyon on the Naval Weapons Center.

DTIC Science & Technology

1983-03-01

Black -headed Grosbeak m Lazuli Bunting b House Finch a Lesser Goldfinch b Inyo Brown Towhee b Black - throated Sparrow a...Scott’s Oriole 1.5 House Finch 30.3 Black - throated Sparrow 3.3 66.8 Sage Sparrow 2.3 4.5 Brewer’s Sparrow 181.0 105.8 AVERAGE PAIRS/40 ha 286.4 200.1...Pipilo fuscus eremoghilus Rufous-crowned Sparrow 2 Almophila ruflceps Black - throated Sparrow Amahispiza bilineata 78 I NWC TP 6424 I Table

Ecological Assessment of the Effects of Army Training Activities on a Desert Ecosystem. National Training Center, Fort Irwin, California

DTIC Science & Technology

1985-06-01

predators .) Several bird species ( black - throated sparrows , LeConte’s...7.3 7.7 12.5 33 28 23 24 39 Black - throated Sparrow - Amphispiza bilineata 5.0 0.3 6.7 7.7 4.5 16 1 21 24 14 Brewer’s Sparrow - Spizella breweri 6.5 0...identified as sensitive indicators of disturbances. The absence of black - throated sparrows and LeConte’s thrashers * indicate severely degraded habitats.

Dual nozzle aerodynamic and cooling analysis study. [dual throat and dual expander nozzles

NASA Technical Reports Server (NTRS)

Meagher, G. M.

1980-01-01

Geometric, aerodynamic flow field, performance prediction, and heat transfer analyses are considered for two advanced chamber nozzle concepts applicable to Earth-to-orbit engine systems. Topics covered include improvements to the dual throat aerodynamic and performance prediction program; geometric and flow field analyses of the dual expander concept; heat transfer analysis of both concepts, and engineering analysis of data from the NASA/MSFC hot-fire testing of a dual throat thruster model thrust chamber assembly. Preliminary results obtained are presented in graphs.

Construction and test of flexible walls for the throat of the ILR high-speed wind tunnel

NASA Technical Reports Server (NTRS)

Igeta, Y.

1983-01-01

Aerodynamic tests in wind tunnels are jeopardized by the lateral limitations of the throat. This influence expands with increasing size of the model in proportion to the cross-section of the throat. Wall interference of this type can be avoided by giving the wall the form of a stream surface that would be identical to the one observed during free flight. To solve this problem, flexible walls that can adapt to every contour of surface flow are needed.

Some tests on small-scale rectangular throat ejector. [thrust augmentation for V/STOL aircraft

NASA Technical Reports Server (NTRS)

Dean, W. N., Jr.; Franke, M. E.

1979-01-01

A small scale rectangular throat ejector with plane slot nozzles and a fixed throat area was tested to determine the effects of diffuser sidewall length, diffuser area ratio, and sidewall nozzle position on thrust and mass augmentation. The thrust augmentation ratio varied from approximately 0.9 to 1.1. Although the ejector did not have good thrust augmentation performance, the effects of the parameters studied are believed to indicate probable trends in thrust augmenting ejectors.

Fast acting multiple element valve

DOEpatents

Yang, Jefferson Y. S.; Wada, James M.

1991-01-01

A plurality of slide valve elements having plural axial-spaced annular parts and an internal slide are inserted into a bulkhead in a fluid conduit from a downstream side of the bulkhead, locked in place by a bayonet coupling and set screw, and project through the bulkhead into the upstream conduit. Pneumatic lines connecting the slide valve element actuator to pilot valves are brought out the throat of the valve element to the downstream side. Pilot valves are radially spaced around the exterior of the valve to permit the pneumatic lines to be made identical, thereby to minimize adverse timing tolerances in operation due to pressure variations. Ring manifolds surround the valve adjacent respective pilot valve arrangements to further reduce adverse timing tolerances due to pressure variations, the manifolds being directly connected to the respective pilot valves. Position sensors are provided the valve element slides to signal the precise time at which a slide reaches or passes through a particular point in its stroke to initiate a calibrated timing function.

Descemet's Stripping Automated Endothelial Keratoplasty Tissue Insertion Devices

PubMed Central

Khan, Salman Nasir; Shiakolas, Panos S.; Mootha, Venkateswara Vinod

2015-01-01

This review study provides information regarding the construction, design, and use of six commercially available endothelial allograft insertion devices applied for Descemet's stripping automated endothelial keratoplasty (DSAEK). We also highlight issues being faced in DSAEK and discuss the methods through which medical devices such as corneal inserters may alleviate these issues. Inserter selection is of high importance in the DSAEK procedure since overcoming the learning curve associated with the use of an insertion device is a time and energy consuming process. In the present review, allograft insertion devices were compared in terms of design, construction material, insertion technique, dimensions, incision requirements and endothelial cell loss to show their relative merits and capabilities based on available data in the literature. Moreover, the advantages/disadvantages of various insertion devices used for allograft insertion in DSAEK are reviewed and compared. The information presented in this review can be utilized for better selection of an insertion device for DSAEK. PMID:27051492

Anemia in the Newborn

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Birth Injury in Newborns

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Prospective surveillance of streptococcal sore throat in a tropical country.

PubMed

Steer, Andrew C; Jenney, Adam W J; Kado, Joseph; Good, Michael F; Batzloff, Michael; Magor, Graham; Ritika, Roselyn; Mulholland, Kim E; Carapetis, Jonathan R

2009-06-01

Acute rheumatic fever and rheumatic heart disease cause a high burden of disease in Fiji and surrounding Pacific Island countries, but little is known about the epidemiology of group A streptococcal (GAS) pharyngitis in the region. We designed a study to estimate the prevalence of carriage of beta-hemolytic streptococci (BHS) and the incidence of BHS culture-positive sore throat in school aged children in Fiji. We conducted twice-weekly prospective surveillance of school children aged 5 to 14 years in 4 schools in Fiji during a 9-month period in 2006, after an initial phase of pharyngeal swabbing to determine the prevalence of BHS carriage. We enrolled 685 children. The prevalence of GAS carriage was 6.0%, while the prevalence of group C streptococcal (GCS) and group G streptococcal (GGS) carriage was 6.9% and 12%, respectively. There were 61 episodes of GAS culture-positive sore throat during the study period equating to an incidence of 14.7 cases per 100 child-years (95% CI, 11.2-18.8). The incidence of GCS/GGS culture-positive sore throat was 28.8 cases per 100 child-years (95% CI, 23.9-34.5). The clinical nature of GAS culture-positive sore throat was more severe than culture-negative sore throat, but overall was mild compared with that found in previous studies. Of the 101 GAS isolates that emm sequence typed there were 45 emm types with no dominant types. There were very few emm types commonly encountered in industrialized nations and only 9 of the 45 emm types found in this study are emm types included in the 26-valent GAS vaccine undergoing clinical trials. GAS culture-positive sore throat was more common than expected. Group C and group G streptococci were frequently isolated in throat cultures, although their contribution to pharyngeal infection is not clear. The molecular epidemiology of pharyngeal GAS in our study differed greatly from that in industrialized nations and this has implications for GAS vaccine clinical research in Fiji and other tropical developing countries.

A Study to Determine if Addition of Palatal Petechiae to Centor Criteria Adds More Significance to Clinical Diagnosis of Acute Strep Pharyngitis in Children.

PubMed

Nibhanipudi, Kumara V

2016-01-01

Objective. A study to determine if addition of palatal petechiae to Centor criteria adds more value for clinical diagnosis of acute strep pharyngitis in children. Hypothesis. In children, Centor Criteria does not cover all the symptoms and signs of acute strep pharyngitis. We hypothesize that addition of palatal petechiae to Centor Criteria will increase the possibility of clinical diagnosis of group A streptococcal pharyngitis in children. Methods. One hundred patients with a complaint of sore throat were enrolled in the study. All the patients were examined clinically using the Centor Criteria. They were also examined for other signs and symptoms like petechial lesions over the palate, abdominal pain, and skin rash. All the patients were given rapid strep tests, and throat cultures were sent. No antibiotics were given until culture results were obtained. Results. The sample size was 100 patients. All 100 had fever, sore throat, and erythema of tonsils. Twenty of the 100 patients had tonsillar exudates, 85/100 had tender anterior cervical lymph nodes, and 86/100 had no cough. In total, 9 out of the 100 patients had positive throat cultures. We observed that petechiae over the palate, a very significant sign, is not included in the Centor Criteria. Palatal petechiae were present in 8 out of the 100 patients. Six out of these 8 with palatal petechiae had positive throat culture for strep (75%). Only 7 out of 20 with exudates had positive strep culture. Sixteen out of the 100 patients had rapid strep test positive. Those 84/100 who had negative rapid strep also had negative throat culture. Statistics. We used Fisher's exact test, comparing throat culture positive and negative versus presence of exudates and palatal hemorrhages with positive and negative throat cultures and the resultant P value <.0001. Conclusion. Our study concludes that addition of petechiae over the palate to Centor Criteria will increase the possibility of diagnosing acute group A streptococcal pharyngitis in children.

Intravenous dexamethasone versus ketamine gargle versus intravenous dexamethasone combined with ketamine gargle for evaluation of post-operative sore throat and hoarseness: A randomized, placebo-controlled, double blind clinical trial

PubMed Central

Safavi, Mohammadreza; Honarmand, Azim; Fariborzifar, Arghavan; Attari, Mohammadali

2014-01-01

Background: Sore throat and hoarseness are the most frequent subjective complaints after tracheal intubation for general anesthesia. We conducted a prospective, randomized, double-blind, placebo controlled study to evaluate the efficacy of intravenous (IV) dexamethasone plus ketamine gargle for reducing the incidence and severity of post-operative sore throat (POST) and hoarseness. Materials and Methods: 140 patients (aged 16-65 year) scheduled for elective surgery were enrolled. Patients were randomly allocated into four groups of 35 subjects each: Group K, gargled 40 mg ketamine in 30 ml saline; Group D, were infused 0.2 mg/kg IV dexamethasone; Group KD, gargled 40 mg ketamine in 30 ml saline plus 0.2 mg/kg IV dexamethasone; Group P (placebo) that received saline (gargle and IV). POST was graded at 0, 2, 4, 8, 16 and 24 h after operation on a four-point scale (0-3). Results: The incidence and severity of POST were significantly lower in Group KD, compared with the other groups at all times after tracheal extubation for up to 24 h (P < 0.05). Also the incidence and severity of hoarseness were significantly lower in each Groups of KD and K and D compared with group placebo (P < 0.05). Conclusion: The prophylactic use of 0.2 mg/kg of IV dexamethasone plus ketamine gargle significantly reduced the incidence and severity of POST compared with using each of these drugs alone or using placebo. PMID:25371869

Large for Gestational Age (LGA)

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Disorders of Amino Acid Metabolism

MedlinePlus

... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ... Drugs Ear, Nose, and Throat Disorders Eye Disorders Fundamentals Heart and Blood Vessel Disorders Hormonal and Metabolic ...

Tonsillitis (For Teens)

MedlinePlus

... bacteria are causing the infection. If you have strep throat , you'll need treatment with an antibiotic to ... prevent other problems that can come from untreated strep throat. If your doctor prescribes antibiotics, be sure to ...

Advanced ceramic material for high temperature turbine tip seals

NASA Technical Reports Server (NTRS)

Vogan, J. W.; Solomon, N. G.; Stetson, A. R.

1980-01-01

Forty-one material systems were evaluated for potential use in turbine blade tip seal applications at 1370 C. Both ceramic blade tip inserts and abradable ceramic tip shoes were tested. Hot gas erosion, impact resistance, thermal stability, and dynamic rub performance were the criteria used in rating the various materials. Silicon carbide and silicon nitride were used, both as blade tips and abradables. The blade tip inserts were fabricated by hot pressing while low density and honeycomb abradables were sintered or reaction bonded.

Double layered tailorable advanced blanket insulation

NASA Technical Reports Server (NTRS)

Falstrup, D.

1983-01-01

An advanced flexible reusable surface insulation material for future space shuttle flights was investigated. A conventional fly shuttle loom with special modifications to weave an integral double layer triangular core fabric from quartz yarn was used. Two types of insulating material were inserted into the cells of the fabric, and a procedure to accomplish this was developed. The program is follow up of a program in which single layer rectangular cell core fabrics are woven and a single type of insulating material was inserted into the cells.

Challenges for Insertion of Structural Nanomaterials in Aerospace Applications

NASA Technical Reports Server (NTRS)

Sochi, Emilie J.

2012-01-01

In the two decades since Iijima's report on carbon nanotubes (CNT), there has been great interest in realizing the benefits of mechanical properties observed at the nanoscale in large-scale structures. The weight savings possible due to dramatic improvements in mechanical properties relative to state-of-the-art material systems can be game changing for applications like aerospace vehicles. While there has been significant progress in commercial production of CNTs, major aerospace applications that take advantage of properties offered by this material have yet to be realized. This paper provides a perspective on the technical challenges and barriers for insertion of CNTs as an emerging material technology in aerospace applications and proposes approaches that may reduce the typical timeframe for technology maturation and insertion into aerospace structures.

What's a Nice Hummingbird Like You Doing at an AGU Meeting Like This? (or, Operation RubyThroat Meets The GLOBE Program)

NASA Astrophysics Data System (ADS)

Hilton, B.

2003-12-01

"Operation RubyThroat: The Hummingbird Project" is an international cross-disciplinary initiative that uses Ruby-throated Hummingbirds (Archilochus colubris) as a hook to excite K-12 students (and adults) about science learning. In 2002, Operation RubyThroat affiliated with The GLOBE Program as the first GLOBE protocol that involves animal behavior. Through Operation RubyThroat, students make observations about hummingbird phenology, behavior, and ecology and correlate their data against traditional GLOBE observations of atmosphere, climate, land cover, soils, hydrology, and phenology. Although Ruby-throated Hummingbirds (RTHUs) breed throughout the eastern half of the United States and southern Canada and may be the most common and most widely distributed of all 338 hummingbird species, little is known about how abiotic environmental factors affect their migration, nesting activities, and everyday behavior. Operation RubyThroat participants in the U.S. and Canada log early arrival dates of RTHUs during spring migration, note their presence throughout the breeding season, and report the last date RTHUs are seen in autumn. Conversely, participants in Mexico and all seven Central American countries (the region in which RTHUs spend their non-breeding months) watch for early arrivals in fall and late departures in spring. Participants also attempt to estimate numbers of RTHUs in local populations by counting the number of visits hummingbirds make to feeders and/or flowers in a 45-minute time block. Optional activities include observations of RTHU nesting behaviors and determining RTHU preferences for various species of native and exotic nectar sources. Participating schools are encouraged to establish Schoolyard Hummingbird Habitats in which to make their observations, but data may be collected in backyards or at local parks, nature centers, botanical gardens, and other sites where RTHUs occur. Adults not affiliated with K-12 schools are invited to become certified in the hummingbird protocols and to submit Operation RubyThroat data to GLOBE. Participants report sightings of any RTHUs that are banded and color-marked with dye or that have unusual plumage (albinistic, leucistic, etc.). Participants in the eastern U.S. and Canada also report the occurrence of "winter vagrant" hummingbirds, i.e., species from the western U. S. and Mexico that from August through March seem to be wandering more frequently into the region. These unusual movements by western hummingbird species, as well as migration timing and winter occurrences of RTHUs, are correlated against GLOBE data to determine possible effects of atmosphere, climate, and land use, including the impact of global warming. As a new GLOBE protocol, Operation RubyThroat is just beginning to generate data for analysis. Operation RubyThroat's collaboration with GLOBE is funded by a grant from the National Science Foundation. Support for other aspects of the project comes from, among others, Agilent Technologies, ConocoPhillips (through National Fish and Wildlife Foundation), The Christensen Fund, and individual donors. Operation RubyThroat is an education, research, and conservation initiative of Hilton Pond Center for Piedmont Natural History (www.hiltonpond.org) in York, South Carolina USA.

Strep Test: Rapid (For Parents)

MedlinePlus

... third of negative rapid strep test results are false (meaning someone actually has a strep throat infection even though the rapid strep results were negative). A throat culture may then be done to ensure accuracy. Risks ...

Cariprazine

MedlinePlus

... severe muscle stiffness muscle weakness or aching blank facial expression difficulty swallowing or breathing tightness in the throat tongue that sticks out of the mouth rash itching hives swelling of the face, throat, tongue, lips, or eyes dark or cola- ...

Enlarged Adenoids (For Parents)

MedlinePlus

... topic for: Parents Kids Teens Tonsils and Tonsillectomies Strep Throat Obstructive Sleep Apnea Preparing Your Child for Surgery ... the Operating Room? Snoring Tonsillitis All About Adenoids Strep Throat Enlarged Adenoids Tonsils and Tonsillectomies What's It Like ...

Polymer quantization of the Einstein-Rosen wormhole throat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kunstatter, Gabor; Peltola, Ari; Louko, Jorma

2010-01-15

We present a polymer quantization of spherically symmetric Einstein gravity in which the polymerized variable is the area of the Einstein-Rosen wormhole throat. In the classical polymer theory, the singularity is replaced by a bounce at a radius that depends on the polymerization scale. In the polymer quantum theory, we show numerically that the area spectrum is evenly spaced and in agreement with a Bohr-Sommerfeld semiclassical estimate, and this spectrum is not qualitatively sensitive to issues of factor ordering or boundary conditions except in the lowest few eigenvalues. In the limit of small polymerization scale we recover, within the numericalmore » accuracy, the area spectrum obtained from a Schroedinger quantization of the wormhole throat dynamics. The prospects of recovering from the polymer throat theory a full quantum-corrected spacetime are discussed.« less

CONTROL OF STREPTOCOCCAL THROAT INFECTIONS IN SCHOOLS—A Cooperative Program Followed in Orange County

PubMed Central

Russell, Edward Lee

1956-01-01

Attempts to identify streptococcal throat infections on clinical evidence alone do not provide an adequate or reliable index of the prevalence of these infections in the community. Epidemiologic information on streptococcal throat infections based on bacteriological identification permits a more accurate assessment of the situation and more logical and more effective control measures. Recent refinements in laboratory procedures have provided a simple, reliable and relatively inexpensive method for the identification of Group A beta hemolytic streptococci by public health or clinical laboratories. In Orange County a program for the identification of streptococcal throat infections by cooperative action of the medical profession, the health department and the school authorities greatly aided in control of the disease. A voluntary health agency (heart association) made an important contribution toward the success of the control program. PMID:13374555

Changes in the pore network structure of Hanford sediment after reaction with caustic tank wastes.

PubMed

Crandell, L E; Peters, C A; Um, W; Jones, K W; Lindquist, W B

2012-04-01

At the former nuclear weapon production site in Hanford, WA, caustic radioactive tank waste leaks into subsurface sediments and causes dissolution of quartz and aluminosilicate minerals, and precipitation of sodalite and cancrinite. This work examines changes in pore structure due to these reactions in a previously-conducted column experiment. The column was sectioned and 2D images of the pore space were generated using backscattered electron microscopy and energy dispersive X-ray spectroscopy. A pre-precipitation scenario was created by digitally removing mineral matter identified as secondary precipitates. Porosity, determined by segmenting the images to distinguish pore space from mineral matter, was up to 0.11 less after reaction. Erosion-dilation analysis was used to compute pore and throat size distributions. Images with precipitation had more small and fewer large pores. Precipitation decreased throat sizes and the abundance of large throats. These findings agree with previous findings based on 3D X-ray CMT imaging, observing decreased porosity, clogging of small throats, and little change in large throats. However, 2D imaging found an increase in small pores, mainly in intragranular regions or below the resolution of the 3D images. Also, an increase in large pores observed via 3D imaging was not observed in the 2D analysis. Changes in flow conducting throats that are the key permeability-controlling features were observed in both methods. Copyright © 2012 Elsevier B.V. All rights reserved.

Development and Testing of the Europa Mission's Venturi Flow Meter

NASA Technical Reports Server (NTRS)

Diaz, C. E.; McKim, S. A.

2017-01-01

NASA's Marshall Space Flight Center (MSFC), in collaboration with NASA's Goddard Space Flight Center (GSFC), Fox Valve Development Corp. and Oxford Lasers, is developing a set of venturi flow meters for use on the Europa Mission's propulsion subsystem. The requirement for the venturi flow meters' throat diameters is approximately 0.040". An early risk reduction activity conducted by MSFC revealed that a venturi flow meter produced by FOX with a throat diameter near 0.040" had much higher pressure loss than venturi flow meters with larger throat diameters and venturis of similar throat diameter size but with no pressure taps (i.e. venturis with a throat length to diameter ratio of zero). In response, a series of venturi flow meters was fabricated and flow tested to gain insight into pressure recovery as it is affected by pressure port diameter, throat length and diffuser angle in an effort to improve the performance of a venturi flow meter. This presentation provides a summary of the venturi flow meter development activity including: a description of the test's objectives, a detailed description of each venturi configuration, a description of the manufacturing processes of the venturis, and observations from the test data. A summary of the current development activities will also be given, as well as the current development path forward. Ultimately, the knowledge gained through the fabrication and testing of these venturis provides guidance to design a flight venturi flow meters with pressure recoveries that is acceptable for the Europa flight application.

Effect of shoe insert construction on foot and leg movement.

PubMed

Nigg, B M; Khan, A; Fisher, V; Stefanyshyn, D

1998-04-01

The purpose of this study was to quantify changes in foot eversion and tibial rotation during running resulting from systematic changes of material composition of five shoe inserts of the same shape. Tests were performed with 12 subjects. The inserts had a bilayer design using two different materials at the top and bottom of the insert. The functional kinematic variables examined in this study were the foot-leg in-eversion angle, beta, and the leg-foot tibial rotation, rho. Additionally, the subject characteristics of arch height, relative arch deformation, and active range of motion were quantified. The statistical analysis used was a two way repeated measures MANOVA (within trials and inserts). The average group changes resulting from the studied inserts in total shoe eversion, total foot eversion, and total internal tibial rotation were typically smaller than 1 degree when compared with the no-insert condition and were statistically not significant. The measured ranges of total foot eversion for all subjects were smallest for the softest and about twice as large for the hardest insert construction. Thus, the soft insert construction was more restrictive, forcing all feet into a similar movement pattern, whereas the harder combinations allowed for more individual variation of foot and leg movement and did not force the foot into a preset movement pattern. The individual results showed substantial differences between subjects and a trend: Subjects who generally showed a reduction of tibial rotation with all tested inserts typically had a flexible foot. However, subjects who generally showed an increase of tibial rotation typically had a stiff foot. The results of this study suggest that subject specific factors such as static, dynamic, and neuro-physiological characteristics of foot and leg are important to match specific feet and shoe inserts optimally.

Testing Mercury Porosimetry with 3D Printed Porosity Models

NASA Astrophysics Data System (ADS)

Hasiuk, F.; Ewing, R. P.; Hu, Q.

2014-12-01

Mercury intrusion porosimetry is one of the most widely used techniques to study the porous nature of a geological and man-made materials. In the geosciences, it is commonly used to describe petroleum reservoir and seal rocks as well as to grade aggregates for the design of asphalt and portland cement concretes. It's wide utility stems from its ability to characterize a wide range of pore throat sizes (from nanometers to around a millimeter). The fundamental physical model underlying mercury intrusion porosimetry, the Washburn Equation, is based on the assumption that rock porosity can be described as a bundle of cylindrical tubes. 3D printing technology, also known as rapid prototyping, allows the construction of intricate and accurate models, exactly what is required to build models of rock porosity. We evaluate the applicability of the Washburn Equation by comparing properties (like porosity, pore and pore throat size distribution, and surface area) computed on digital porosity models (built from CT data, CAD designs, or periodic geometries) to properties measured via mercury intrusion porosimetry on 3D printed versions of the same digital porosity models.

On the Influence of Material Parameters in a Complex Material Model for Powder Compaction

NASA Astrophysics Data System (ADS)

Staf, Hjalmar; Lindskog, Per; Andersson, Daniel C.; Larsson, Per-Lennart

2016-10-01

Parameters in a complex material model for powder compaction, based on a continuum mechanics approach, are evaluated using real insert geometries. The parameter sensitivity with respect to density and stress after compaction, pertinent to a wide range of geometries, is studied in order to investigate completeness and limitations of the material model. Finite element simulations with varied material parameters are used to build surrogate models for the sensitivity study. The conclusion from this analysis is that a simplification of the material model is relevant, especially for simple insert geometries. Parameters linked to anisotropy and the plastic strain evolution angle have a small impact on the final result.

Effect of insertion torque on bone screw pullout strength.

PubMed

Lawson, K J; Brems, J

2001-05-01

The effect of insertion torque on the holding strength of 4.5-mm ASIF/AO cortical bone screws was studied in vitro. Screw holding strength was determined using an Instron materials testing machine (Bristol, United Kingdom) on 55 lamb femora and 30 human tibiocortical bone sections. Holding strength was defined as tensile stress at pullout with rapid loading to construct failure. Different insertion torques were tested, normalizing to the thickness of cortical bone specimen engaged. These represented low, intermediate, high, and thread-damaging insertion torque. All screws inserted with thread-damaging torque and single cortex engaging screws inserted to high torque tightening moments showed diminished holding strength. This loss of strength amounted to 40%-50% less than screws inserted with less torque.

Reactor pressure vessel nozzle

DOEpatents

Challberg, R.C.; Upton, H.A.

1994-10-04

A nozzle for joining a pool of water to a nuclear reactor pressure vessel includes a tubular body having a proximal end joinable to the pressure vessel and a distal end joinable in flow communication with the pool. The body includes a flow passage therethrough having in serial flow communication a first port at the distal end, a throat spaced axially from the first port, a conical channel extending axially from the throat, and a second port at the proximal end which is joinable in flow communication with the pressure vessel. The inner diameter of the flow passage decreases from the first port to the throat and then increases along the conical channel to the second port. In this way, the conical channel acts as a diverging channel or diffuser in the forward flow direction from the first port to the second port for recovering pressure due to the flow restriction provided by the throat. In the backflow direction from the second port to the first port, the conical channel is a converging channel and with the abrupt increase in flow area from the throat to the first port collectively increase resistance to flow therethrough. 2 figs.

Surface Damage on Dental Implants with Release of Loose Particles after Insertion into Bone

PubMed Central

Senna, Plinio; Del Bel Cury, Altair Antoninha; Kates, Stephen; Meirelles, Luiz

2015-01-01

Background Modern dental implants present surface features of distinct dimensions that can be damaged during the insertion procedure into bone. Purpose The aims of this study were (1) to quantify by means of roughness parameters the surface damage caused by the insertion procedure of dental implants and (2) to investigate the presence of loose particles at the interface. Materials and Methods Three groups of dental implants representing different surface topographies were inserted in fresh cow rib bone blocks. The surface roughness was characterized by interferometry on the same area before and after the insertion. SEM-BSD analysis was used to identify loose particles at the interface. Results The amplitude and hybrid roughness parameters of all three groups were lower after insertion. The surface presenting predominance of peaks (Ssk>0) associated to higher structures (height parameters) presented higher damage associated to more pronounced reduction of material volume. SEM-BSD images revealed loose titanium and aluminum particles at the interface mainly at the crestal cortical bone level. Conclusions Shearing forces during the insertion procedure alters the surface of dental implants. Loose metal particles can be generated at bone-implant interface especially around surfaces composed mainly by peaks and with increased height parameters. PMID:24283455

21 CFR 874.5300 - Ear, nose, and throat examination and treatment unit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5300... chair and table, drawers for equipment, suction and blowing apparatus, and receptacles for connection of...

21 CFR 874.5300 - Ear, nose, and throat examination and treatment unit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5300... chair and table, drawers for equipment, suction and blowing apparatus, and receptacles for connection of...

Jewelry cleaners

MedlinePlus

... swelling (may also cause breathing difficulty) EYES, EARS, NOSE, AND THROAT Severe pain in the throat Severe pain or burning in the nose, eyes, ears, lips, or tongue Vision loss GASTROINTESTINAL SYSTEM ... pain (severe) Bloody stools Burns and possible holes of ...

Side Effects: Mouth and Throat Problems

Cancer.gov

Cancer treatments may cause dental, mouth, and throat side effects such as changes in taste (dysgeusia), dry mouth (xerostomia), infections, mouth sores, pain or swelling in your mouth (oral mucositis), sensitivity to foods, and swallowing problems.

Pediatric Obesity and Ear, Nose, and Throat Disorders

MedlinePlus

... Marketplace Find an ENT Doctor Near You Pediatric Obesity and Ear, Nose, and Throat Disorders Pediatric Obesity ... self-esteem, and isolation from their peers. Pediatric obesity and otolaryngic problems Otolaryngologists, or ear, nose, and ...

Mechanical Harvesting of Aquatic Plants. Report 2. Evaluation of Selected Handling Functions of Mechanical Control.

DTIC Science & Technology

1980-06-01

with the extracted plants. Pusher boats were used to feed the plants into the throat of the conveyor where they were then pulled onto the conveyor by...technique or variations of it that involve extracting from the river periodically on the Withlacoochee River or similar rivers, requires 48 that operations...way to readily estimate the land area required to stockpile the large volumes of material that must be extracted from the water in many operational

Experimental Attempts for Deep Insertion in Ultrasonically Forced Insertion Process

NASA Astrophysics Data System (ADS)

Ono, Satoshi; Aoyagi, Manabu; Tamura, Hideki; Takano, Takehiro

2011-07-01

In this paper, we describe two attempts of obtaining deep insertion in an ultrasonically forced insertion (USFI) process. One was to correct the inclination of an inserted rod by passively generated bending vibrations. The inclination causes a partial plastic deformation, which decreases the holding power of processing materials. Two types of horn with grooves for excitation of bending vibrations were examined. The other was to make differences in vibration velocity and the phase of a rod and a metal plate by damping the vibration of a metal plate by using a rubber sheet. As results, the attempts proposed in this study were confirmed to be effective to obtain a deep insertion.

The impact of incubating the throat culture for 72 h on the diagnosis of group A beta-hemolytic streptococci.

PubMed

Kocoglu, Esra; Karabay, Oguz; Yilmaz, Fahrettin; Ekerbicer, Hasan

2006-09-01

The accurate detection and treatment of group A beta-hemolytic streptococcal pharyngitis is important to prevent the potential sequels. Throat culture remains the gold standard for the diagnosis of streptococcal pharyngitis. Many authors recommended 48 h incubation time for the isolation of group A Streptococcus (GAS). In this study the diagnostic efficacy of prolonging the incubation time of throat cultures to 72 h for isolation of GAS was researched. Throat swab specimens were inoculated to 5% sheep blood agar plate and incubated at 37 degrees C, and evaluated at the 24th hour. GAS negative plates were incubated again for another 24h and read at the 48th hour. Negative plates at 48 h were incubated again, read at the 72nd hour, and positive results of all measurements were evaluated. A total of 367 cultures were examined. At the 24th hour evaluation 34 (9.3%) cultures were positive for GAS. Evaluation of 333 cultures that were found to be negative in the first 24th hour evaluation revealed 44 (13.6%) positive cultures at 48th hour evaluation. Out of 289 cultures that were negative during the 48th hour evaluation, an additional 13 (4.7%) cultures were found to be positive during the 72nd hour evaluation. The agreement between 24th-48th and 24th and 72nd were both moderate (kappa 0.54 and 0. 46, respectively), and between 48th and 72nd hour was very good (kappa: 0.90). Throat cultures that are negative for GAS at 24h should be incubated for second day. We conclude that, to confirm the throat cultures GAS negative, results of throat cultures need to be incubated for 72 h, since 72nd hour evaluations revealed additional 5% positive results.

Island biology and morphological divergence of the Skyros wall lizard Podarcis gaigeae: a combined role for local selection and genetic drift on color morph frequency divergence?

PubMed Central

2010-01-01

Background Patterns of spatial variation in discrete phenotypic traits can be used to draw inferences about the adaptive significance of traits and evolutionary processes, especially when compared to patterns of neutral genetic variation. Population divergence in adaptive traits such as color morphs can be influenced by both local ecology and stochastic factors such as genetic drift or founder events. Here, we use quantitative color measurements of males and females of Skyros wall lizard, Podarcis gaigeae, to demonstrate that this species is polymorphic with respect to throat color, and the morphs form discrete phenotypic clusters with limited overlap between categories. We use divergence in throat color morph frequencies and compare that to neutral genetic variation to infer the evolutionary processes acting on islet- and mainland populations. Results Geographically close islet- and mainland populations of the Skyros wall lizard exhibit strong divergence in throat color morph frequencies. Population variation in throat color morph frequencies between islets was higher than that between mainland populations, and the effective population sizes on the islets were small (Ne:s < 100). Population divergence (FST) for throat color morph frequencies fell within the neutral FST-distribution estimated from microsatellite markers, and genetic drift could thus not be rejected as an explanation for the pattern. Moreover, for both comparisons among mainland-mainland population pairs and between mainland-islet population pairs, morph frequency divergence was significantly correlated with neutral divergence, further pointing to some role for genetic drift in divergence also at the phenotypic level of throat color morphs. Conclusions Genetic drift could not be rejected as an explanation for the pattern of population divergence in morph frequencies. In spite of an expected stabilising selection, throat color frequencies diverged in the islet populations. These results suggest that there is an interaction between selection and genetic drift causing divergence even at a phenotypic level in these small, subdivided populations. PMID:20813033

Sore Throat: Symptoms and Causes

MedlinePlus

... of the mouth, throat and voice box. Allergies. Seasonal allergies or ongoing allergic reactions to dust, molds ... HIV, diabetes, treatment with steroids or chemotherapy drugs, stress, fatigue, and ... when soap and water aren't available. Avoid touching public phones or ...

Internal performance characteristics of vectored axisymmetric ejector nozzles

NASA Technical Reports Server (NTRS)

Lamb, Milton

1993-01-01

A series of vectoring axisymmetric ejector nozzles were designed and experimentally tested for internal performance and pumping characteristics at NASA-Langley Research Center. These ejector nozzles used convergent-divergent nozzles as the primary nozzles. The model geometric variables investigated were primary nozzle throat area, primary nozzle expansion ratio, effective ejector expansion ratio (ratio of shroud exit area to primary nozzle throat area), ratio of minimum ejector area to primary nozzle throat area, ratio of ejector upper slot height to lower slot height (measured on the vertical centerline), and thrust vector angle. The primary nozzle pressure ratio was varied from 2.0 to 10.0 depending upon primary nozzle throat area. The corrected ejector-to-primary nozzle weight-flow ratio was varied from 0 (no secondary flow) to approximately 0.21 (21 percent of primary weight-flow rate) depending on ejector nozzle configuration. In addition to the internal performance and pumping characteristics, static pressures were obtained on the shroud walls.

Sore throat: Is it such a big deal anymore?

PubMed

Herath, Verangi C K; Carapetis, Jonathan

2015-06-01

Sore throat remains a common disease of childhood, and a major cost and cause for antibiotic prescriptions. The management of sore throat remains controversial in affluent countries with various guidelines available and overall poor adherence to those guidelines. Group A streptococcus is the commonest bacterial cause with important sequelae including acute rheumatic fever (ARF). The driver for diagnosis and treatment is still questionable. In most affluent populations it is difficult to justify antibiotic treatment on the basis of preventing ARF, whereas this remains the major driver for sore throat management in populations at higher risk of ARF. Reduction in severity and duration of symptoms may be a reasonable basis to consider antibiotic treatment, and thus accurate diagnosis of GAS pharyngitis, particularly in those with more severe symptoms. The potential role of rapid tests in diagnosis appears to be increasing. Copyright © 2015 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

Improvement on Main/backup Controller Switching Device of the Nozzle Throat Area Control System for a Turbofan Aero Engine

NASA Astrophysics Data System (ADS)

Li, Jie; Duan, Minghu; Yan, Maode; Li, Gang; Li, Xiaohui

2014-06-01

A full authority digital electronic controller (FADEC) equipped with a full authority hydro-mechanical backup controller (FAHMBC) is adopted as the nozzle throat area control system (NTACS) of a turbofan aero engine. In order to ensure the switching reliability of the main/backup controller, the nozzle throat area control switching valve was improved from three-way convex desktop slide valve to six-way convex desktop slide valve. Simulation results show that, if malfunctions of FAEDC occur and abnormal signals are outputted from FADEC, NTACS will be seriously influenced by the main/backup controller switching in several working states, while NTACS will not be influenced by using the improved nozzle throat area control switching valve, thus the controller switching process will become safer and smoother and the working reliability of this turbofan aero engine is improved by the controller switching device improvement.

Diagnosis of group A streptococcal infections directly from throat secretions.

PubMed Central

Edwards, E A; Phillips, I A; Suiter, W C

1982-01-01

The diagnosis of group A streptococcal disease still relies on isolation of group A streptococcal strains on sheep blood agar followed by presumptive identification based on bacitracin sensitivity or the results of the more precise serogrouping methods such as the Lancefield precipitin test. A technique that would permit rapid identification of streptococcal infections directly from throat secretions would allow immediate appropriate antimicrobial therapy for the management of streptococcal infections to be started. We have been able to identify soluble group A antigen directly from throat secretions by using a latex agglutination test. In a clinical trial in which latex (Streptex group A) and conventional culturing techniques were used, 53 throat secretion cultures were tested: 26 were positive by both procedures, 5 were positive by culture only, 3 were positive by the latex agglutination test only, and 19 were negative by both tests. Images PMID:7042747

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. A larger image is available without labels (No. 0101755).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830).

International migration patterns of Red-throated Loons (Gavia stellata) from four breeding populations in Alaska

USGS Publications Warehouse

McCloskey, Sarah E.; Uher-Koch, Brian D.; Schmutz, Joel A.; Fondell, Thomas F.

2018-01-01

Identifying post-breeding migration and wintering distributions of migratory birds is important for understanding factors that may drive population dynamics. Red-throated Loons (Gavia stellata) are widely distributed across Alaska and currently have varying population trends, including some populations with recent periods of decline. To investigate population differentiation and the location of migration pathways and wintering areas, which may inform population trend patterns, we used satellite transmitters (n = 32) to describe migration patterns of four geographically separate breeding populations of Red-throated Loons in Alaska. On average (± SD) Red-throated Loons underwent long (6,288 ± 1,825 km) fall and spring migrations predominantly along coastlines. The most northern population (Arctic Coastal Plain) migrated westward to East Asia and traveled approximately 2,000 km farther to wintering sites than the three more southerly populations (Seward Peninsula, Yukon-Kuskokwim Delta, and Copper River Delta) which migrated south along the Pacific coast of North America. These migration paths are consistent with the hypothesis that Red-throated Loons from the Arctic Coastal Plain are exposed to contaminants in East Asia. The three more southerly breeding populations demonstrated a chain migration pattern in which the more northerly breeding populations generally wintered in more northerly latitudes. Collectively, the migration paths observed in this study demonstrate that some geographically distinct breeding populations overlap in wintering distribution while others use highly different wintering areas. Red-throated Loon population trends in Alaska may therefore be driven by a wide range of effects throughout the annual cycle.

Rapid PCR detection of group A Streptococcus from flocked throat swabs: a retrospective clinical study.

PubMed

Slinger, Robert; Goldfarb, David; Rajakumar, Derek; Moldovan, Ioana; Barrowman, Nicholas; Tam, Ronald; Chan, Francis

2011-09-02

Rapid diagnosis of GAS pharyngitis may improve patient care by ensuring that patients with GAS pharyngitis are treated quickly and also avoiding unnecessary use of antibiotics in those without GAS infection. Very few molecular methods for detection of GAS in clinical throat swab specimens have been described. We performed a study of a laboratory-developed internally-controlled rapid Group A streptococcus (GAS) PCR assay using flocked swab throat specimens. We compared the GAS PCR assay to GAS culture results using a collection of archived throat swab samples obtained during a study comparing the performance of conventional and flocked throat swabs. The sensitivity of the GAS PCR assay as compared to the reference standard was 96.0% (95% CI 90.1% to 98.4%), specificity 98.6% (95% CI 95.8% to 99.5%), positive predictive value (PPV) 96.9% (95% CI 91.4% to 99.0%) and negative predictive value (NPV) of 98.1% (95% CI 95.2% to 99.2%). For conventional swab cultures, sensitivity was 96.0% (95% CI 90.1% to 98.4%), specificity 100% (95% CI 98.2% to 100%), PPV 100%, (95% CI 96.1% to 100%) and NPV 98.1% (95% CI 95.2% to 99.3%) In this retrospective study, the GAS PCR assay appeared to perform as well as conventional throat swab culture, the current standard of practice. Since the GAS PCR assay, including DNA extraction, can be performed in approximately 1 hour, prospective studies of this assay are warranted to evaluate the clinical impact of the assay on management of patients with pharyngitis.

Management of patients with sore throats in relation to guidelines: an interview study in Sweden.

PubMed

Hedin, Katarina; Strandberg, Eva Lena; Gröndal, Hedvig; Brorsson, Annika; Thulesius, Hans; André, Malin

2014-12-01

To explore how a group of Swedish general practitioners (GPs) manage patients with a sore throat in relation to current guidelines as expressed in interviews. Qualitative content analysis was used to analyse semi-structured interviews. Swedish primary care. A strategic sample of 25 GPs. Perceived management of sore throat patients. It was found that nine of the interviewed GPs were adherent to current guidelines for sore throat and 16 were non-adherent. The two groups differed in terms of guideline knowledge, which was shared within the team for adherent GPs while idiosyncratic knowledge dominated for the non-adherent GPs. Adherent GPs had no or low concerns for bacterial infections and differential diagnosis whilst non-adherent GPs believed that in patients with a sore throat any bacterial infection should be identified and treated with antibiotics. Patient history and examination was mainly targeted by adherent GPs whilst for non-adherent GPs it was often redundant. Non-adherent GPs reported problems getting patients to abstain from antibiotics, whilst no such problems were reported in adherent GPs. This interview study of sore throat management in a strategically sampled group of Swedish GPs showed that while two-thirds were non-adherent and had a liberal attitude to antibiotics one-third were guideline adherent with a restricted view on antibiotics. Non-adherent GPs revealed significant knowledge gaps. Adherent GPs had discussed guidelines within the primary care team while non-adherent GPs had not. Guideline implementation thus seemed to be promoted by knowledge shared in team discussions.

Immunological evaluation of polystyrene and poly(ether imide) cell culture inserts with different roughness.

PubMed

Roch, Toralf; Krüger, Anne; Kratz, Karl; Ma, Nan; Jung, Friedrich; Lendlein, Andreas

2012-01-01

For the successful clinical and biological application of polymers, their interaction with cells, tissues, and body fluids has to be well characterized. In order to investigate how the physical, chemical, and mechanical properties of candidate biomaterials influence cell behaviours, the testing sample is usually placed in commercially available cell culture plates. Thus, not only the testing sample itself but also the culture dish material might influence the cell behaviour. Therefore, an insert system was created to exclude this influence and allow investigations of the testing material solely. In this study micropatterned inserts prepared from polystyrene (PS) as well as from poly(ether imide) (PEI) with three different roughness levels of i) Rq = 0.29 μm (PS) and 0.23 μm (PEI); ii) Rq = 3.47 μm (PS) and 3.92 μm (PEI); and iii) Rq = 22.16 μm [corrected] (PS) and 22.65 μm (PEI) were explored with regard of their immuno-compatibility including the determination of potential contaminations with endotoxins or other microbial products. The endotoxin levels of the inserts were determined to be less than 0.07 EU/mL, which is well below the U.S. Food and Drug Administration limit of 0.5 EU/mL and the survival of murine macrophages cultured in the inserts was not impaired. Activation of early immune mechanisms such as complement activation and the generation of reactive oxygen species could not be observed. All tested materials had no influence on the cytokine secretion from cells of whole human blood. The investigated inserts were immuno-compatible and apparently free of contaminations with microbial products. The roughness of the inserts had no stimulatory or inhibitory effect on early immune mechanisms. Conclusively, the 24-well plate insert systems introduced in this study allow investigating the interactions of tailored surface properties such as roughness with many other cell types, without the disadvantage of the standard commercially available culture vessels influencing the biomaterial testing.

Fiber optic connector

DOEpatents

Rajic, Slobodan; Muhs, Jeffrey D.

1996-01-01

A fiber optic connector and method for connecting composite materials within which optical fibers are imbedded. The fiber optic connector includes a capillary tube for receiving optical fibers at opposing ends. The method involves inserting a first optical fiber into the capillary tube and imbedding the unit in the end of a softened composite material. The capillary tube is injected with a coupling medium which subsequently solidifies. The composite material is machined to a desired configuration. An external optical fiber is then inserted into the capillary tube after fluidizing the coupling medium, whereby the optical fibers are coupled.

Efficacy of flurbiprofen 8.75 mg delivered as a spray or lozenge in patients with sore throat due to upper respiratory tract infection: a randomized, non-inferiority trial in the Russian Federation.

PubMed

Radkova, Eugenia; Burova, Natalia; Bychkova, Valeria; DeVito, Robert

2017-01-01

To assess the efficacy of flurbiprofen 8.75 mg delivered as a spray or lozenge in patients with sore throat due to upper respiratory tract infection (URTI). This multicenter, double-blind, double-dummy, non-inferiority study randomized 440 adults with recent-onset, moderate-to-severe sore throat due to URTI to a single dose of either flurbiprofen 8.75 mg spray (n=218) or flurbiprofen 8.75 mg lozenge (n=222). The presence or absence of beta-hemolytic streptococci (A or C) was confirmed by culture tests (throat swab). The primary efficacy end point was the difference from baseline to 2 hours post-dose in sore throat pain intensity scale (STPIS pain intensity difference [PID] 2h), a validated 100 mm visual analog scale (from 0="no pain" to 100="severe pain"), with a non-inferiority margin of -6 mm. Secondary end points included STPIS PID at 1 hour (STPIS PID 1h) and over 2 hours (STPIS sum of sore throat pain intensity differences [SPID] 0-2h ) and ratings of patient satisfaction and investigator assessment of drug efficacy at 2 hours. Safety (adverse events [AEs]) was also assessed. Reductions in sore throat pain intensity at 2 hours (STPIS PID 2h) were similar for spray (least square mean -40.51) and lozenge (-40.10) (difference: 0.41, 95% confidence interval [95% CI] -3.20, 4.01), with non-inferiority demonstrated. Subgroup analyses showed similar efficacy (STPIS PID 2h) for patients testing positive or negative for Strep A or C. There was no significant difference between spray and lozenge in STPIS PID 1h or STPIS SPID 0-2h , and patient satisfaction and investigators' assessment of efficacy at 2 hours were similar for both groups. There were no significant differences in AEs between the two groups, with 17 drug-related events across both groups, all being mild and none being serious. Both formulations demonstrated comparable efficacy and safety profiles and provide patients with two different treatment formats to choose from for effective symptomatic relief of sore throat, depending on their preference.

Innovative SPM Probes for Energy-Storage Science: MWCNT-Nanopipettes to Nanobattery Probes

NASA Astrophysics Data System (ADS)

Larson, Jonathan; Talin, Alec; Pearse, Alexander; Kozen, Alexander; Reutt-Robey, Janice

As energy-storage materials and designs continue to advance, new tools are needed to direct and explore ion insertion/de-insertion at well-defined battery materials interfaces. Scanned probe tips, assembled from actual energy-storage materials, permit SPM measures of local cathode-anode (tip-sample) interactions, including ion transfer. We present examples of ``cathode'' MWCNT-terminated STM probe tips interacting with Li(s)/Si(111) anode substrates. The MWCNT tip functions as both SPM probe and Li-nanopipette,[1] for controlled transport and manipulation of Li. Local field conditions for lithium ionization and transfer are determined and compared to electrostatic models. Additional lithium metallic and oxide tips have been prepared by thin film deposition on conventional W tips, the latter of which effectively functions as a nanobattery. We demonstrate use of these novel probe materials in the local lithiation of low-index Si anode interfaces, probing local barriers for lithium insertion. Prospects and limitations of these novel SPM probes will be discussed. U.S. Department of Energy Award Number DESC0001160.

The microbiology of ethmoid and maxillary sinuses in patients with chronic sinusitis.

PubMed

Aral, Murat; Keles, Erol; Kaygusuz, Irfan

2003-01-01

To investigate aerob-anaerob microorganisms growth in maxillary and ethmoid sinuses by evaluating aspiration materials from patients with chronic sinusitis. The study was performed prospectively, and there were 31 patients (23 men, 8 women; mean age, 31.4+/-14.15, between 18-65 years) who had endoscopic sinus surgery because of chronic sinusitis. During the operation, when the maxillary sinus ostium and ethmoid sinus were opened, readily aspirated materials from sinuses were evaluated regarding aerob and anaerob bacteria. Nose and throat swap samples were collected preoperatively to determine the upper respiratory tract flora and also to understand the relationship between the flora and the microorganisms aspirated from sinuses. Total aerob bacteria count, which was isolated from preoperative nasal swab cultures, was 36, and aerob-anaerob bacteria count that included cultures taken from maxillary and ethmoid sinuses during the functional endoscopic sinus surgery was 42. For each 2 samples, the most common isolated aerob bacteria were coagulase (-) staphylococci. Microorganisms were isolated in 87.0% of 27 patients, in which cultures taken from maxillary and ethmoid sinuses during the functional endoscopic sinus surgery were included. It is determined that the isolated aerob bacteria rate was 90.4%, and the isolated anaerob bacteria rate was 14.2%. All of the 6 samples in which anaerob bacteria isolated were all maxillary sinus aspiration materials. Microorganisms that isolated from the nose and the sinuses were similar with the rate of 25.8%, and microorganisms that isolated from the throat cultures and sinuses were similar with the rate of 22.5%. This study reveals the aerob and anaerob microbiology of the maxillary and ethmoid sinuses so the treatment of chronic sinusitis will be easier.

Application of Deep Cryogenic Treatment to Uncoated Tungsten Carbide Inserts in the Turning of AISI 304 Stainless Steel

NASA Astrophysics Data System (ADS)

Özbek, Nursel Altan; Çİçek, Adem; Gülesİn, Mahmut; Özbek, Onur

2016-12-01

This study investigated the effects of deep cryogenic treatment (DCT) on the wear performance of uncoated tungsten carbide inserts. AISI 304 austenitic stainless steel, widely used in industry, was selected as the workpiece material. Cutting experiments showed that the amount of wear significantly increased with increasing cutting speed. In addition, it was found that DCT contributed to the wear resistance of the turning inserts. The treated turning inserts were less worn by 48 and 38 pct in terms of crater wear and notch wear, respectively, whereas they exhibited up to 18 pct superior wear performance in terms of flank wear. This was attributed to the precipitation of new and finer η-carbides and their homogeneous distribution in the microstructure of the tungsten carbide material after deep cryogenic treatment. Analyses via image processing, hardness measurements, and SEM observations confirmed these findings.

Ablative material testing for low-pressure, low-cost rocket engines

NASA Technical Reports Server (NTRS)

Richter, G. Paul; Smith, Timothy D.

1995-01-01

The results of an experimental evaluation of ablative materials suitable for the production of light weight, low cost rocket engine combustion chambers and nozzles are presented. Ten individual specimens of four different compositions of silica cloth-reinforced phenolic resin materials were evaluated for comparative erosion in a subscale rocket engine combustion chamber. Gaseous hydrogen and gaseous oxygen were used as propellants, operating at a nominal chamber pressure of 1138 kPa (165 psi) and a nominal mixture ratio (O/F) of 3.3. These conditions were used to thermally simulate operation with RP-1 and liquid oxygen, and achieved a specimen throat gas temperature of approximately 2456 K (4420 R). Two high-density composition materials exhibited high erosion resistance, while two low-density compositions exhibited approximately 6-75 times lower average erosion resistance. The results compare favorably with previous testing by NASA and provide adequate data for selection of ablatives for low pressure, low cost rocket engines.

Vocal Cord Paralysis

MedlinePlus

... paralysis. Known causes may include: Injury to the vocal cord during surgery. Surgery on or near your neck or upper ... Factors that may increase your risk of developing vocal cord paralysis include: Undergoing throat or chest surgery. People who need surgery on their thyroid, throat ...

Development of an organ-specific insert phantom generated using a 3D printer for investigations of cardiac computed tomography protocols.

PubMed

Abdullah, Kamarul A; McEntee, Mark F; Reed, Warren; Kench, Peter L

2018-04-30

An ideal organ-specific insert phantom should be able to simulate the anatomical features with appropriate appearances in the resultant computed tomography (CT) images. This study investigated a 3D printing technology to develop a novel and cost-effective cardiac insert phantom derived from volumetric CT image datasets of anthropomorphic chest phantom. Cardiac insert volumes were segmented from CT image datasets, derived from an anthropomorphic chest phantom of Lungman N-01 (Kyoto Kagaku, Japan). These segmented datasets were converted to a virtual 3D-isosurface of heart-shaped shell, while two other removable inserts were included using computer-aided design (CAD) software program. This newly designed cardiac insert phantom was later printed by using a fused deposition modelling (FDM) process via a Creatbot DM Plus 3D printer. Then, several selected filling materials, such as contrast media, oil, water and jelly, were loaded into designated spaces in the 3D-printed phantom. The 3D-printed cardiac insert phantom was positioned within the anthropomorphic chest phantom and 30 repeated CT acquisitions performed using a multi-detector scanner at 120-kVp tube potential. Attenuation (Hounsfield Unit, HU) values were measured and compared to the image datasets of real-patient and Catphan ® 500 phantom. The output of the 3D-printed cardiac insert phantom was a solid acrylic plastic material, which was strong, light in weight and cost-effective. HU values of the filling materials were comparable to the image datasets of real-patient and Catphan ® 500 phantom. A novel and cost-effective cardiac insert phantom for anthropomorphic chest phantom was developed using volumetric CT image datasets with a 3D printer. Hence, this suggested the printing methodology could be applied to generate other phantoms for CT imaging studies. © 2018 The Authors. Journal of Medical Radiation Sciences published by John Wiley & Sons Australia, Ltd on behalf of Australian Society of Medical Imaging and Radiation Therapy and New Zealand Institute of Medical Radiation Technology.

Static internal performance of a two-dimensional convergent-divergent nozzle with thrust vectoring

NASA Technical Reports Server (NTRS)

Bare, E. Ann; Reubush, David E.

1987-01-01

A parametric investigation of the static internal performance of multifunction two-dimensional convergent-divergent nozzles has been made in the static test facility of the Langley 16-Foot Transonic Tunnel. All nozzles had a constant throat area and aspect ratio. The effects of upper and lower flap angles, divergent flap length, throat approach angle, sidewall containment, and throat geometry were determined. All nozzles were tested at a thrust vector angle that varied from 5.60 tp 23.00 deg. The nozzle pressure ratio was varied up to 10 for all configurations.

Towards multi-field D-brane inflation in a warped throat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Heng-Yu; Gong, Jinn-Ouk; Koyama, Kazuya

2010-11-01

We study the inflationary dynamics in a model of slow-roll inflation in warped throat. Inflation is realized by the motion of a D-brane along the radial direction of the throat, and at later stages instabilities develop in the angular directions. We closely investigate both the single field potential relevant for the slow-roll phase, and the full multi-field one including the angular modes which becomes important at later stages. We study the main features of the instability process, discussing its possible consequences and identifying the vacua towards which the angular modes are driven.

Impact of droplet evaporation rate on resulting in vitro performance parameters of pressurized metered dose inhalers.

PubMed

Sheth, Poonam; Grimes, Matthew R; Stein, Stephen W; Myrdal, Paul B

2017-08-07

Pressurized metered dose inhalers (pMDIs) are widely used for the treatment of pulmonary diseases. The overall efficiency of pMDI drug delivery may be defined by in vitro parameters such as the amount of drug that deposits on the model throat and the proportion of the emitted dose that has particles that are sufficiently small to deposit in the lung (i.e., fine particle fraction, FPF). The study presented examines product performance of ten solution pMDI formulations containing a variety of cosolvents with diverse chemical characteristics by cascade impaction with three inlets (USP induction port, Alberta Idealized Throat, and a large volume chamber). Through the data generated in support of this study, it was demonstrated that throat deposition, cascade impactor deposition, FPF, and mass median aerodynamic diameter of solution pMDIs depend on the concentration and vapor pressure of the cosolvent, and the selection of model throat. Theoretical droplet lifetimes were calculated for each formulation using a discrete two-stage evaporation process model and it was determined that the droplet lifetime is highly correlated to throat deposition and FPF indicating that evaporation kinetics significantly influences pMDI drug delivery. Copyright © 2017 Elsevier B.V. All rights reserved.

Antiproliferative Activity of Triterpene Glycoside Nutrient from Monk Fruit in Colorectal Cancer and Throat Cancer.

PubMed

Liu, Can; Dai, Longhai; Liu, Yueping; Rong, Long; Dou, Dequan; Sun, Yuanxia; Ma, Lanqing

2016-06-13

Colorectal cancer and throat cancer are the world's most prevalent neoplastic diseases, and a serious threat to human health. Plant triterpene glycosides have demonstrated antitumor activity. In this study, we investigated potential anticancer effects of mogroside IVe, a triterpenoid glycoside from monk fruit, using in vitro and in vivo models of colorectal and laryngeal cancer. The effects of mogroside IVe on the proliferation of colorectal cancer HT29 cells and throat cancer Hep-2 cells were determined by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, and the expression levels of p53, phosphorylated ERK1/2, and MMP-9 were analyzed by western blotting and immunohistochemistry. The results indicated that mogroside IVe inhibited, in a dose-dependent manner, the proliferation of HT29 and Hep-2 cells in culture and in xenografted mice, which was accompanied by the upregulation of tumor suppressor p53, and downregulation of matrix metallopeptidase 9 (MMP-9) and phosphorylated extracellular signal-regulated kinases (ERK)1/2. This study revealed the suppressive activity of mogroside IVe towards colorectal and throat cancers and identified the underlying mechanisms, suggesting that mogroside IVe may be potentially used as a biologically-active phytochemical supplement for treating colorectal and throat cancers.

Dual-throat thruster thermal model

NASA Technical Reports Server (NTRS)

Ewen, R. L.; Obrien, C. J.; Matthews, L. W.

1986-01-01

The dual-throat engine is one of the dual nozzle engine concepts studied for advanced space transportation applications. It provides a thrust change and an in-flight area ratio change through the use of two concentric combustors with their throats arranged in series. Test results are presented for a dual throat thruster burning gaseous oxygen and hydrogen at primary (inner) chamber pressures from 380 to 680 psia. Heat flux profiles were obtained from calorimetric cooling channels in the inner nozzle, outer or secondary chamber and the tip of the inner nozzle. Data were obtained for two nozzle spacings over a chamber pressure ratio (secondary/primary) range of 0.45 to 0.83 with both chambers firing (Mode I). Fluxes near the end of the inner nozzle were significantly higher than in Mode II when only the inner chamber was fired, due to the flow separation and recirculation caused by the back pressure imposed by the secondary chamber. As the pressure ratio increased, these heat fluxes increased and the region of high heat flux relative to Mode II extended farther upstream. The use of the gaseous hydrogen bleed flow in the secondary chamber to control heat fluxes in the primary plume attachment region was investigated in Mode II testing. A thermal model of a dual throat thruster was developed and upgraded using the experimental data.

Egg flotation estimates nest age for Pacific and Red-throated Loons

USGS Publications Warehouse

Rizzolo, Daniel; Schmutz, Joel A.

2007-01-01

We used Pacific Loon (Gavia pacifica) and Red-throated Loon (G. stellata) nests with known ages to gauge the efficacy of egg flotation for determining nest age in coastal Alaska. Egg flotation accurately estimated nest age for both species; the mean ± 1SD difference between known age and age determined with egg flotation was - 0.05 ± 2.00 d and -0.02 ± 1.63 d for Pacific and Red-throated Loons, respectively. Day of nest initiation did not influence the relationship between known nest age and nest age estimated with egg flotation, indicating incubation period was not shortened in nests initiated later in the season. Additionally, we found no difference in the ability of egg flotation to estimate nest age between two widely dispersed study sites for Pacific Loons, and only a small difference between two of three widely dispersed study sites for Red-throated Loons. Thus, our described relationships between egg flotation categories and nest age should be broadly applicable for these holarctic species. We conclude that for Pacific and Red-throated Loons, egg flotation is a useful technique for determining nest age in the field to better monitor nest fate, and to quantify nest age effects on nest daily survival rate.

Empirical validation of guidelines for the management of pharyngitis in children and adults.

PubMed

McIsaac, Warren J; Kellner, James D; Aufricht, Peggy; Vanjaka, Anita; Low, Donald E

2004-04-07

Recent guidelines for management of pharyngitis vary in their recommendations concerning empirical antibiotic treatment and the need for laboratory confirmation of group A streptococcus (GAS). To assess the impact of guideline recommendations and alternative approaches on identification and treatment of GAS pharyngitis in children and adults. Throat cultures and rapid antigen tests were performed on 787 children and adults aged 3 to 69 years with acute sore throat attending a family medicine clinic in Calgary, Alberta, from September 1999 to August 2002. Recommendations from 2 guidelines (those of the Infectious Diseases Society of America and of the American College of Physicians-American Society of Internal Medicine/American Academy of Family Physicians/US Centers for Disease Control and Prevention) were compared with rapid testing alone, a clinical prediction rule (ie, the modified Centor score), and a criterion standard of treatment for positive throat culture results only. Sensitivity and specificity of each strategy for identifying GAS pharyngitis, total antibiotics recommended, and unnecessary antibiotic prescriptions. In children, sensitivity for streptococcal infection ranged from 85.8% (133/155; 95% confidence interval [CI], 79.3%-90.0%) for rapid testing to 100% for culturing all. In adults, sensitivity ranged from 76.7% (56/73; 95% CI, 65.4%-85.8%) for rapid testing without culture confirmation of negative results to 100% for culturing all. In children, specificity ranged from 90.3% (270/299; 95% CI, 86.4%-93.4%) for use of modified Centor score and throat culture to 100% for culturing all. In adults, specificity ranged from 43.8% (114/260; 95% CI, 37.7%-50.1%) for empirical treatment based on a modified Centor score of 3 or 4 to 100% for culturing all. Total antibiotic prescriptions were lowest with rapid testing (24.7% [194/787]; 95% CI, 21.7%-27.8%) and highest with empirical treatment of high-risk adults (45.7% [360/787]; 95% CI, 42.2%-49.3%), due to a high rate of unnecessary prescriptions in adults (43.8% [146/333]; 95% CI, 38.4%-49.4%). Guideline recommendations for the selective use of throat cultures but antibiotic treatment based only on positive rapid test or throat culture results can reduce unnecessary use of antibiotics for treatment of pharyngitis. However, empirical treatment of adults having a Centor score of 3 or 4 is associated with a high rate of unnecessary antibiotic use. In children, strategies incorporating throat culture or throat culture confirmation of negative rapid antigen test results are highly sensitive and specific. Throat culture of all adults or those selected on the basis of a clinical prediction rule had the highest sensitivity and specificity.

Efficiency of a clinical prediction model for selective rapid testing in children with pharyngitis: A prospective, multicenter study

PubMed Central

Cohen, Robert; Bidet, Philippe; Elbez, Annie; Levy, Corinne; Bossuyt, Patrick M.; Chalumeau, Martin

2017-01-01

Background There is controversy whether physicians can rely on signs and symptoms to select children with pharyngitis who should undergo a rapid antigen detection test (RADT) for group A streptococcus (GAS). Our objective was to evaluate the efficiency of signs and symptoms in selectively testing children with pharyngitis. Materials and methods In this multicenter, prospective, cross-sectional study, French primary care physicians collected clinical data and double throat swabs from 676 consecutive children with pharyngitis; the first swab was used for the RADT and the second was used for a throat culture (reference standard). We developed a logistic regression model combining signs and symptoms with GAS as the outcome. We then derived a model-based selective testing strategy, assuming that children with low and high calculated probability of GAS (<0.12 and >0.85) would be managed without the RADT. Main outcomes and measures were performance of the model (c-index and calibration) and efficiency of the model-based strategy (proportion of participants in whom RADT could be avoided). Results Throat culture was positive for GAS in 280 participants (41.4%). Out of 17 candidate signs and symptoms, eight were retained in the prediction model. The model had an optimism-corrected c-index of 0.73; calibration of the model was good. With the model-based strategy, RADT could be avoided in 6.6% of participants (95% confidence interval 4.7% to 8.5%), as compared to a RADT-for-all strategy. Conclusions This study demonstrated that relying on signs and symptoms for selectively testing children with pharyngitis is not efficient. We recommend using a RADT in all children with pharyngitis. PMID:28235012

Pumpable rockbolt method

DOEpatents

Steinberg, Meyer; Manowitz, Bernard; Waide, Charles H.

1976-01-06

Method and apparatus for producing rockbolts in the roof of a subterranean cavity in which two components of an ambient temperature curable resin system are premixed and then inserted into a bore hole. The mixture is permitted to polymerize in situ and then the hardened material is cut off at the entrance to the hole leaving a hardened portion for insertion into the next hole as a precursor. In a preferred embodiment a flexible glass roving is employed to reinforce the material in the hole and a metal tube inserted to support the roving while it is fed into the hole and also to provide venting. The roving and tube is then cut off and left in the hole.

Internally folded expanded metal electrode for battery construction

NASA Technical Reports Server (NTRS)

Pierce, Doug C. (Inventor); Korinek, Paul D. (Inventor); Morgan, Maurice C. (Inventor)

1993-01-01

A battery system is disclosed which includes folded grids of expanded metal inserted through non-conductive substrates and pasted with electrochemically active materials. In the most preferred embodiment, a frame is provided with a plastic insert, and slots are provided in the latter to receive the expanded metal grid. After suitable coinage of the grid and insertion through the plastic film, the grid is sealed and pasted on opposite sides with positive and negative active material. A battery is assembled using one or a plurality of the resulting electrode elements, with separators, to produce a high-power, lead-acid battery. The folded grid provides many of the design benefits of standard bipolar construction.

A sticky situation: management of spray polyurethane foam insulation in body orifices.

PubMed

Sowerby, Robert J; Sowerby, Leigh J; Vinden, Chris

2011-11-01

Spray polyurethane foam insulation is commonly used in the construction industry to fill gaps, seal, and insulate. We present three cases of intentional spray foam insertion in body orifices and discuss the management of such situations in the emergency department. This series includes a case of oral foam insertion used in a suicide attempt by suffocation and two cases of rectal insertion. All of these cases had potential long-term consequences; one was life-threatening. To our knowledge, this is the first published report on the medical management and removal of foam insulation from body orifices. In all three cases, the foam insulation material was successfully removed after allowing the material to harden.

[Current requirements for polymeric biomaterials in ear, nose and throat medicine].

PubMed

Sternberg, K

2009-05-01

In recent years the ear, nose and throat medicine (ENT medicine) has been stimulated by numerous innovations in the field of implants which are based on new biomaterials and modern implant technologies. In this context, biomaterials integrated in living organisms have to allow for the technical requirements and the biological interactions between the implant and the tissue. With regard to their suitability, functional capability of the implant, which is complementary to the mechanical implant properties, sufficient stability against physiological media, as well as high biocompatibility are to be demanded. Another purpose of the use of biomaterials is the maintenance and the enhancement of biofunctionality over a long time period. These general requirements for biomaterials also have their validity in ENT medicine. Different materials are applied as biomaterials. Metals belong to the oldest biomaterials. In addition, alloys, ceramics, inorganic glasses and composites were tested. Furthermore, natural and synthetic polymers, which are primarily presented in this article regarding their properties and their applications as materials for cochlear implants, osteosynthesis implants, stents and novel scaffolds for tissue engineering, are increasingly applied. According to their use in permanent and temporary implants, polymers are to be differentiated between biostable and biodegradable polymers. The presented general and current requirements for biomaterials and biomaterial applications in ENT medicine demonstrate key aspects of the current biomaterial research in this field. They do as well document the high impact of the interdisciplinary collaboration of natural and medical scientists and engineers.

Evaluating the suitability of highly cross-linked and remelted materials for use in posterior stabilized knees.

PubMed

Huot, J Caitlin; Van Citters, Douglas W; Currier, John H; Currier, Barbara H; Mayor, Michael B; Collier, John P

2010-11-01

Posterior stabilized (PS) knee designs are a popular choice for cruciate sacrificing knee arthroplasty procedures. The introduction of PS inserts fabricated from highly cross-linked and remelted Ultra High Molecular Weight Polyethylene (UHMWPE) has recently generated concern as these materials have been shown to possess reduced mechanical properties. This study investigated whether highly cross-linked and remelted UHMWPE material (referred to as XRP) can be expected to perform similarly to historical gamma-air polyethylene, which has suffered few reported incidences of tibial post failure. Never-implanted gamma-air PS tibial inserts shelf-aged 14 years were examined and compared to XRP materials. Evaluation of oxidation levels, impact toughness, and fatigue strength demonstrated never-implanted gamma-air PS tibial inserts to possess nonuniform mechanical properties. Despite severe oxidation along the exterior of gamma-air tibial posts, comparatively low oxidation levels at the center of the tibial posts corresponded to sufficiently high mechanical properties. XRP material (75 kGy) showed superior impact toughness over shelf aged gamma-air material; however, tibial post fatigue testing demonstrated XRP material (100 kGy) to be less resistant to fatigue failure than historical gamma-air material. Results from this study indicate that XRP materials (100 kGy) may demonstrate an inferior resistance to tibial post failure than historical polyethylene. © 2010 Wiley Periodicals, Inc.

Observation of crystalline changes of titanium dioxide during lithium insertion by visible spectrum analysis.

PubMed

Nam, Inho; Park, Jongseok; Park, Soomin; Bae, Seongjun; Yoo, Young Geun; Han, Jeong Woo; Yi, Jongheop

2017-05-24

Real-time analysis of changes in the atomic environment of materials is a cutting edge technology that is being used to explain reaction dynamics in many fields of science. Previously, this kind of analysis was only possible using heavy nucleonic equipment such as XANES and EXAFS, or Raman spectroscopy on a moderate scale. Here, a new methodology is described that can be used to track changes in crystalline developments during complex Li insertion reactions via the observation of structural color. To be specific, the changes in atomic crystalline and nanostructure are shown during Li insertion in a complex TiO 2 polymorph. Structural color corresponds to the refractive indices of materials originating from their atomic bonding nature and precise wave interferences in accordance with their nanostructure. Therefore, this new analysis simultaneously reveals changes in the nanostructure as well as changes in the atomic bonding nature of materials.

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD). This image is from a digital still camera; higher resolution is not available.

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Here the transparent furnace is extracted for servicing. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, and TBD). This composite is from a digital still camera; higher resolution is not available.

Superconductive wire

DOEpatents

Korzekwa, David A.; Bingert, John F.; Peterson, Dean E.; Sheinberg, Haskell

1995-01-01

A superconductive article is made by inserting a rigid mandrel into an internal cavity of a first metallic tube, said tube having an interior surface and an exterior surface, said interior surface defining the interior cavity, forming a layer of a superconductive material or superconductive precursor upon the exterior surface of said first metallic tube, machining the layer of superconductive material or superconductive precursor to a predetermined diameter to form an intermediate article configured for insertion into a second metallic tube having an interior diameter corresponding to the predetermined diameter, inserting the machined intermediate article into a second metallic tube having an internal diameter corresponding to the predetermined diameter of the intermediate article to form a composite intermediate article, reducing or ironing the composite intermediate article to a predetermined cross-sectional diameter, and sintering the reduced or ironed composite intermediate article at temperatures and for time sufficient for the superconductive material or superconductive precursor to exhibit superconductivity.

Superconductive wire

DOEpatents

Korzekwa, D.A.; Bingert, J.F.; Peterson, D.E.; Sheinberg, H.

1995-07-18

A superconductive article is made by inserting a rigid mandrel into an internal cavity of a first metallic tube, said tube having an interior surface and an exterior surface, said interior surface defining the interior cavity, forming a layer of a superconductive material or superconductive precursor upon the exterior surface of said first metallic tube, machining the layer of superconductive material or superconductive precursor to a predetermined diameter to form an intermediate article configured for insertion into a second metallic tube having an interior diameter corresponding to the predetermined diameter, inserting the machined intermediate article into a second metallic tube having an internal diameter corresponding to the predetermined diameter of the intermediate article to form a composite intermediate article, reducing or ironing the composite intermediate article to a predetermined cross-sectional diameter, and sintering the reduced or ironed composite intermediate article at temperatures and for time sufficient for the superconductive material or superconductive precursor to exhibit superconductivity. 2 figs.

Mononucleosis

MedlinePlus

... foods and drink lots of water to prevent dehydration. If you have a sore throat, gargle saltwater, drink tea with honey, or suck on hard candy or ice pops. You can get some nutrition and soothe your throat with cold fruit smoothies or low-fat shakes. When you start ...

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Material Requirements. 52....211-5 Material Requirements. As prescribed in 11.304, insert the following clause: Material... components, whether manufactured from virgin material, recovered material in the form of raw material, or...

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 2 2014-10-01 2014-10-01 false Material Requirements. 52....211-5 Material Requirements. As prescribed in 11.304, insert the following clause: Material... components, whether manufactured from virgin material, recovered material in the form of raw material, or...

Which is the best method to trace group A streptococci in sore throat patients: culture or GAS antigen test?

PubMed

Lindbaek, Morten; Høiby, Ernst Arne; Lermark, Gro; Steinsholt, Inger Marie; Hjortdahl, Per

2004-12-01

To compare an antigen detection test (GAS antigen test) with the results from combinations of two various bacteriological test media in general practice patients with sore throat. Furthermore to assess the diagnostic properties of the chosen GAS antigen test and to compare semi-quantitative results of this test with the bacterial load found in the throat culture. Two Norwegian general practices in Stokke and Kongsberg communities. 306 patients with sore throat lasting less than 7 days; 244 were adults, 62 were children under 10 years old, mean age 23.9 years (SD 15.0), 40% were men. Results from GAS antigen test, and distribution of bacteriological findings in throat cultures, compared with the results of our GAS antigen test; semi-quantitative results of the GAS antigen test compared with the bacterial load by culture. In the primary culture 110 patients harboured group A streptococci (GAS) infection, while the second culture identified another 17, giving a total of 127 patients. Some 33 patients harboured large-colony groups C and G. The GAS antigen test used had a sensitivity of 97% and specificity of 95% regarding GAS when compared with the two cultures. We found a significant correlation between the bacterial loads by culture and the semi-quantitative results of the GAS antigen test. By using a second, different set of bacteriological media, we identified an additional 17 patients with GAS infections. This raises the question of validity of frequently used reference standards in studies related to streptococcal infections. Compared with the combined results of the two throat cultures, the GAS antigen test used showed high sensitivity and specificity. Semi-quantitative evaluations of the rapid immunological test may also be of clinical value.

NORMAL FLORA OF THE NOSE, THROAT, AND LOWER INTESTINE OF DOGS

PubMed Central

Clapper, W. E.; Meade, G. H.

1963-01-01

Clapper, W. E. (The Lovelace Foundation for Medical Education and Research, Albuquerque, N.M.) and G. H. Meade. Normal flora of the nose, throat, and lower intestine of dogs. J. Bacteriol. 85:643–648. 1963.—An attempt was made to isolate and identify the complete normal flora of the rectum, nose, and throat of beagles. For primary isolation, 12 different kinds of media were used. Incubation of blood agar plates and slants anaerobically, and of thioglycolate broth aerobically, allowed the growth of obligate anaerobes. From the rectal specimens, 20 species of bacteria and 10 species of fungi were isolated and identified. The organisms were similar to those found in the human intestine. Escherichia coli, Streptococcus mitis, enterococci, S. lactis, Bacillus species, and coliforms other than E. coli were most frequently encountered. The frequency of occurrence was approximately the same at both samplings in more commonly cultured bacteria. Pathogenic E. coli were isolated from nearly one-third of the first specimens. These were the only human pathogens observed. In the throat cultures, 29 species of bacteria and 2 species of yeasts were identified, and 27 species of bacteria were identified from the nasal cultures. S. mitis, Neisseria, and coagulase-negative Staphylococcus were most often isolated. The flora was similar to that found in human nose and throat cultures, except that more Haemophilus and pneumococcus and fewer coliforms are generally found in human throats. Organisms resembling human pathogens were group A streptococci and coagulase-positive staphylococci. These were isolated infrequently. It appears that this kind of examination would reveal any significant changes in normal flora that might be related to the health of the animal. PMID:14042944

Survey of Spanish general practitioners' attitudes toward management of sore throat: an internet-based questionnaire study.

PubMed

Llor, Carl; Vilaseca, Isabel; Lehrer-Coriat, Eduardo; Boleda, Xavier; Cañada, José L; Moragas, Ana; Cots, Josep M

2017-02-14

The management of sore throat varies widely in Europe. The objective of this study was to gain insight into clinicians' perceptions on the current management of sore throat in Spain. Cross-sectional, internet-based questionnaire study answered from July to September 2013. General practitioners (GPs) affiliated with the two largest scientific societies of primary care were invited to participate in the study. Questions were asked about physician knowledge, the use of current national guidelines for sore throat management, and management in two clinical scenarios, depicting a young adult with sore throat and: 1. cough, coriza with or without fever, and 2. fever without cough and coriza. The questionnaire was completed by 1476 GPs (5%) and 12.7% declared using rapid antigen detection tests. Antibiotics were considered by 18.8% of the GPs in the first scenario and by 32% in the second scenario (p < 0.001). The antibiotics most commonly mentioned by GPs were amoxicillin and amoxicillin + clavulanate (52.7 and 31.2%, respectively) whereas penicillin V was only prescribed in 11.9% of the cases. The drugs most commonly considered in both scenarios were analgesics and anti-inflammatory drugs. Antitussives, decongestants and expectorants were more commonly prescribed in cases of suspected viral infection (p < 0.001). GPs have misconceptions as to the indications for using rapid antigen detection tests and prescribing drugs in the management of sore throat. These results suggest that guidelines are seldom followed since one in five GPs declared giving antibiotics for patients with a suspected viral infection and the use of second-choice antibiotics seems considerable.

Detection of Japanese Encephalitis Virus RNA in Human Throat Samples in Laos - A Pilot study.

PubMed

Bharucha, Tehmina; Sengvilaipaseuth, Onanong; Seephonelee, Malee; Vongsouvath, Malavanh; Vongsouvath, Manivanh; Rattanavong, Sayaphet; Piorkowski, Géraldine; Lecuit, Marc; Gorman, Christopher; Pommier, Jean-David; Newton, Paul N; de Lamballerie, Xavier; Dubot-Pérès, Audrey

2018-05-22

Japanese encephalitis virus (JEV) is the most commonly identified cause of acute encephalitis syndrome (AES) in Asia. The WHO recommended test is anti-JEV IgM-antibody-capture-enzyme-linked-immunosorbent-assay (JEV MAC-ELISA). However, data suggest this has low positive predictive value, with false positives related to other Flavivirus infections and vaccination. JEV RT-PCR in cerebrospinal fluid (CSF) and/or serum is highly specific, but is rarely positive; 0-25% of patients that fulfil the WHO definition of JE (clinical Acute Encephalitis Syndrome (AES) and JEV MAC-ELISA positive). Testing other body fluids by JEV RT-qPCR may improve the diagnosis. As a pilot study thirty patients admitted to Mahosot Hospital 2014-2017, recruited to the South-East-Asia-Encephalitis study, were tested by JEV MAC-ELISA and two JEV real-time RT-PCR (RT-qPCR) assays (NS2A and NS3). Eleven (36.7%) were JEV MAC-ELISA positive. Available CSF and serum samples of these patients were JEV RT-qPCR negative but 2 (7%) had JEV RNA detected in their throat swabs. JEV RNA was confirmed by re-testing, and sequencing of RT-qPCR products. As the first apparent report of JEV RNA detection in human throat samples, the provides new perspectives on human JEV infection, potentially informing improving JEV detection. We suggest that testing patients' throat swabs for JEV RNA is performed, in combination with molecular and serological CSF and serum investigations, on a larger scale to investigate the epidemiology of the presence of JEV in human throats. Throat swabs are an easy and non-invasive tool that could be rolled out to a wider population to improve knowledge of JEV molecular epidemiology.

Effects of sweet flavorings and nicotine on the appeal and sensory properties of e-cigarettes among young adult vapers: Application of a novel methodology.

PubMed

Goldenson, Nicholas I; Kirkpatrick, Matthew G; Barrington-Trimis, Jessica L; Pang, Raina D; McBeth, Julia F; Pentz, Mary Ann; Samet, Jonathan M; Leventhal, Adam M

2016-11-01

Product characteristics that impact e-cigarette appeal by altering the sensory experience of vaping need to be identified to formulate evidence-based regulatory policies. While products that contain sweet flavorings and produce a "throat hit" (i.e., desirable airway irritation putatively caused by nicotine) are anecdotally cited as desirable reasons for vaping among young adults, experimental evidence of their impact on user appeal is lacking. This experiment applied a novel laboratory protocol to assess whether: (1) sweet flavorings and nicotine affect e-cigarette appeal; (2) sweet flavorings increase perceived sweetness; (3) nicotine increases throat hit; and (4) perceived sweetness and throat hit are associated with appeal. Young adult vapers (N=20; age 19-34) self-administered 20 standardized doses of aerosolized e-cigarette solutions varied according to a 3 flavor (sweet [e.g., cotton candy] vs. non-sweet [e.g., tobacco-flavored] vs. flavorless)×2 nicotine (6mg/mL nicotine vs. 0mg/mL [placebo]) double-blind, cross-over design. Participants rated appeal (liking, willingness to use again and perceived monetary value), perceived sweetness and throat hit strength after each administration. Sweet-flavored (vs. non-sweet and flavorless) solutions produced greater appeal and perceived sweetness ratings. Nicotine produced greater throat hit ratings than placebo, but did not significantly increase appeal nor interact with flavor effects on appeal. Controlling for flavor and nicotine, perceived sweetness was positively associated with appeal ratings; throat hit was not positively associated with appeal. Further identification of compounds in e-cigarette solutions that enhance sensory perceptions of sweetness, appeal, and utilization of e-cigarettes are warranted to inform evidence-based regulatory policies. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Incidence and clinical variables associated with streptococcal throat infections: a prospective diagnostic cohort study

PubMed Central

Little, Paul; Hobbs, FD Richard; Mant, David; McNulty, Cliodna AM; Mullee, Mark

2012-01-01

Background Management of pharyngitis is commonly based on features which are thought to be associated with Lancefield group A beta-haemolytic streptococci (GABHS) but it is debatable which features best predict GABHS. Non-group A strains share major virulence factors with group A, but it is unclear how commonly they present and whether their presentation differs. Aim To assess the incidence and clinical variables associated with streptococcal infections. Design and setting Prospective diagnostic cohort study in UK primary care. Method The presence of pathogenic streptococci from throat swabs was assessed among patients aged ≥5 years presenting with acute sore throat. Results Pathogenic streptococci were found in 204/597 patients (34%, 95% CI = 31 to 38%): 33% (68/204) were non-group A streptococci, mostly C (n = 29), G (n = 18) and B (n = 17); rarely D (n = 3) and Streptococcus pneumoniae (n = 1). Patients presented with similar features whether the streptococci were group A or non-group A. The features best predicting A, C or G beta-haemolytic streptococci were patient’s assessment of severity (odds ratio [OR] for a bad sore throat 3.31, 95% CI = 1.24 to 8.83); doctors’ assessment of severity (severely inflamed tonsils OR 2.28, 95% CI = 1.39 to 3.74); absence of a bad cough (OR 2.73, 95% CI = 1.56 to 4.76), absence of a coryza (OR 1.54, 95% CI = 0.99 to 2.41); and moderately bad or worse muscle aches (OR 2.20, 95% CI = 1.41 to 3.42). Conclusion Non-group A strains commonly cause streptococcal sore throats, and present with similar symptomatic clinical features to group A streptococci. The best features to predict streptococcal sore throat presenting in primary care deserve revisiting. PMID:23211183

Incidence and clinical variables associated with streptococcal throat infections: a prospective diagnostic cohort study.

PubMed

Little, Paul; Hobbs, F D Richard; Mant, David; McNulty, Cliodna A M; Mullee, Mark

2012-11-01

Management of pharyngitis is commonly based on features which are thought to be associated with Lancefield group A beta-haemolytic streptococci (GABHS) but it is debatable which features best predict GABHS. Non-group A strains share major virulence factors with group A, but it is unclear how commonly they present and whether their presentation differs. To assess the incidence and clinical variables associated with streptococcal infections. Prospective diagnostic cohort study in UK primary care. The presence of pathogenic streptococci from throat swabs was assessed among patients aged ≥5 years presenting with acute sore throat. Pathogenic streptococci were found in 204/597 patients (34%, 95% CI = 31 to 38%): 33% (68/204) were non-group A streptococci, mostly C (n = 29), G (n = 18) and B (n = 17); rarely D (n = 3) and Streptococcus pneumoniae (n = 1). Patients presented with similar features whether the streptococci were group A or non-group A. The features best predicting A, C or G beta-haemolytic streptococci were patient's assessment of severity (odds ratio [OR] for a bad sore throat 3.31, 95% CI = 1.24 to 8.83); doctors' assessment of severity (severely inflamed tonsils OR 2.28, 95% CI = 1.39 to 3.74); absence of a bad cough (OR 2.73, 95% CI = 1.56 to 4.76), absence of a coryza (OR 1.54, 95% CI = 0.99 to 2.41); and moderately bad or worse muscle aches (OR 2.20, 95% CI = 1.41 to 3.42). Non-group A strains commonly cause streptococcal sore throats, and present with similar symptomatic clinical features to group A streptococci. The best features to predict streptococcal sore throat presenting in primary care deserve revisiting.

Effects of Sweet Flavorings and Nicotine on the Appeal and Sensory Properties of e-Cigarettes Among Young Adult Vapers: Application of a Novel Methodology*

PubMed Central

Goldenson, Nicholas I.; Kirkpatrick, Matthew G.; Barrington-Trimis, Jessica L.; Pang, Raina D.; McBeth, Julia F.; Pentz, Mary Ann; Samet, Jonathan M.; Leventhal, Adam M.

2016-01-01

Introduction Product characteristics that impact e-cigarette appeal by altering the sensory experience of vaping need to be identified to formulate evidence-based regulatory policies. While products that contain sweet flavorings and produce a “throat hit” (i.e., desirable airway irritation putatively caused by nicotine) are anecdotally cited as desirable reasons for vaping among young adults, experimental evidence of their impact on user appeal is lacking. This experiment applied a novel laboratory protocol to assess whether: (1) sweet flavorings and nicotine affect e-cigarette appeal; (2) sweet flavorings increase perceived sweetness; (3) nicotine increases throat hit; and (4) perceived sweetness and throat hit are associated with appeal. Methods Young adult vapers (N=20; age 19–34) self-administered 20 standardized doses of aerosolized e-cigarette solutions varied according to a 3 flavor (sweet [e.g., cotton candy] vs. non-sweet [e.g., tobacco-flavored] vs. flavorless) × 2 nicotine (6 mg/mL nicotine vs. 0 mg/mL [placebo]) double-blind, cross-over design. Participants rated appeal (liking, willingness to use again and perceived monetary value), perceived sweetness and throat hit strength after each administration. Results Sweet-flavored (vs. non-sweet and flavorless) solutions produced greater appeal and perceived sweetness ratings. Nicotine produced greater throat hit ratings than placebo, but did not significantly increase appeal nor interact with flavor effects on appeal. Controlling for flavor and nicotine, perceived sweetness was positively associated with appeal ratings; throat hit was not positively associated with appeal. Conclusions Further identification of compounds in e-cigarette solutions that enhance sensory perceptions of sweetness, appeal, and utilization of e-cigarettes are warranted to inform evidence-based regulatory policies. PMID:27676583

Cyclic voltammetry modeling of proton transport effects on redox charge storage in conductive materials: application to a TiO2 mesoporous film.

PubMed

Kim, Y S; Balland, V; Limoges, B; Costentin, C

2017-07-21

Cyclic voltammetry is a particularly useful tool for characterizing charge accumulation in conductive materials. A simple model is presented to evaluate proton transport effects on charge storage in conductive materials associated with a redox process coupled with proton insertion in the bulk material from an aqueous buffered solution, a situation frequently encountered in metal oxide materials. The interplay between proton transport inside and outside the materials is described using a formulation of the problem through introduction of dimensionless variables that allows defining the minimum number of parameters governing the cyclic voltammetry response with consideration of a simple description of the system geometry. This approach is illustrated by analysis of proton insertion in a mesoporous TiO 2 film.

Lateral acoustic wave resonator comprising a suspended membrane of low damping resonator material

DOEpatents

Olsson, Roy H.; El-Kady; , Ihab F.; Ziaei-Moayyed, Maryam; Branch; , Darren W.; Su; Mehmet F.,; Reinke; Charles M.,

2013-09-03

A very high-Q, low insertion loss resonator can be achieved by storing many overtone cycles of a lateral acoustic wave (i.e., Lamb wave) in a lithographically defined suspended membrane comprising a low damping resonator material, such as silicon carbide. The high-Q resonator can sets up a Fabry-Perot cavity in a low-damping resonator material using high-reflectivity acoustic end mirrors, which can comprise phononic crystals. The lateral overtone acoustic wave resonator can be electrically transduced by piezoelectric couplers. The resonator Q can be increased without increasing the impedance or insertion loss by storing many cycles or wavelengths in the high-Q resonator material, with much lower damping than the piezoelectric transducer material.

Soft Tissue Phantoms for Realistic Needle Insertion: A Comparative Study.

PubMed

Leibinger, Alexander; Forte, Antonio E; Tan, Zhengchu; Oldfield, Matthew J; Beyrau, Frank; Dini, Daniele; Rodriguez Y Baena, Ferdinando

2016-08-01

Phantoms are common substitutes for soft tissues in biomechanical research and are usually tuned to match tissue properties using standard testing protocols at small strains. However, the response due to complex tool-tissue interactions can differ depending on the phantom and no comprehensive comparative study has been published to date, which could aid researchers to select suitable materials. In this work, gelatin, a common phantom in literature, and a composite hydrogel developed at Imperial College, were matched for mechanical stiffness to porcine brain, and the interactions during needle insertions within them were analyzed. Specifically, we examined insertion forces for brain and the phantoms; we also measured displacements and strains within the phantoms via a laser-based image correlation technique in combination with fluorescent beads. It is shown that the insertion forces for gelatin and brain agree closely, but that the composite hydrogel better mimics the viscous nature of soft tissue. Both materials match different characteristics of brain, but neither of them is a perfect substitute. Thus, when selecting a phantom material, both the soft tissue properties and the complex tool-tissue interactions arising during tissue manipulation should be taken into consideration. These conclusions are presented in tabular form to aid future selection.

FLOW SIMULATION IN THE HUMAN UPPER RESPIRATORY TRACT

EPA Science Inventory

ABSTRACT

Computer simulations of airflow patterns within the human upper respiratory tract (URT) are presented. The URT model includes airways of the head (nasal and oral), throat (pharyngeal and laryngeal), and lungs (trachea and main bronchi). The head and throat mor...

Principles of ear nose and throat surgery for pregnant women.

PubMed

Baruah, Paramita; Jasraj, Kailey; Ahmad, Ijaz

2017-04-02

Management of the pregnant surgical patient is challenging. The surgical procedure is usually postponed until the postpartum period, although this may not be possible in emergency situations. This article highlights the optimal management of the pregnant woman requiring ear nose and throat surgery.

Static investigation of several yaw vectoring concepts on nonaxisymmetric nozzles

NASA Technical Reports Server (NTRS)

Mason, M. L.; Berrier, B. L.

1985-01-01

A test has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the flow-turning capability and the effects on nozzle internal performance of several yaw vectoring concepts. Nonaxisymmetric convergent-divergent nozzles with throat areas simulating dry and afterburning power settings and single expansion ramp nozzles with a throat area simulating a dry power setting were modified for yaw thrust vectoring. Forward-thrust and pitch-vectored nozzle configurations were tested with each yaw vectoring concept. Four basic yaw vectoring concepts were investigated on the nonaxisymmetric convergent-divergent nozzles: (1) translating sidewall; (2) downstream (of throat) flaps; (3) upstream (of throat) port/flap; and (4) powered rudder. Selected combinations of the rudder with downstream flaps or upstream port/flap were also tested. A single yaw vectoring concept, post-exit flaps, was investigated on the single expansion ramp nozzles. All testing was conducted at static (no external flow) conditions and nozzle pressure ratios varied from 2.0 up to 10.0.

Rocketdyne - SE-7 and SE-8 Engines. Chapter 4, Appendix F

NASA Technical Reports Server (NTRS)

Harmon, Tim

2009-01-01

The 70-pound SE-7 engine is very similar with its two valves, ablative material, a silicon carbide liner, a silicon carbide throat, and overall configuration. There were different wraps. One had a ninety-degree ablative material orientation. That is important because it caused problems with the SE-8, but not for this application. It was not overly stressed. It was a validation of the off-the-shelf application approach. There were two SE-7 engines located on the stage near the bottom. They had their own propellant tanks. That was the application. All it did was give a little bit of gravity by firing to push the propellants to the bottom of the tanks for start or restart. It was not a particularly complicated setup. (See Slides 6 and 7, Appendix F) What had we learned? This was a proven engine in a space environment. There weren't any development issues. Off-the-shelf seemed to work. There were no operational issues, which made the SE-7 very cost-effective. Besides NASA, the customer for this application was the Douglas Aircraft Company. Douglas decided the off-the-shelf idea was cost-effective. With the Gemini Program, the company was McDonnell Aircraft Corporation, which was part of the reason the off-the-shelf idea was applied to the Apollo. (See Slide 8, Appendix F) However, here are some differences between Apollo and Gemini vehicles. For one thing, the Apollo vehicle was really moving at high speed when it re-entered the atmosphere. Instead of a mere 17,000 miles per hour, it was going 24,000 miles per hour. That meant the heat load was four times as high on the Apollo vehicle as on the Gemini craft. Things were vibrating a little more. We had two redundant systems. Apollo was redundant where it could be as much as possible. That was really a keystone or maybe an anchor point for Apollo. We decided to pursue the off-the-shelf approach. However, the prime contractor was a different entity - the North American Space Division. They thought they ought to tune up this off-the-shelf setup. It was a similar off-the-shelf application, but at a higher speed. They wanted to improve it. What they wanted to improve was the material performance of silicon carbide. They were uncomfortable with the cracks they were seeing. They were uncomfortable with the cracks in the throat, and feeling that the environment was a little tougher, that maybe it was going to rattle, perhaps something would fall out, and they would have a problem. They wanted to eliminate the ceramic liner, and they wanted a different throat material. (See Slides 9 and 10, Appendix F) The Rocketdyne solutions were to replace silicon carbide material with a more forgiving ceramic material. Also, due to the multiple locations within the vehicle, the shape of the nozzles varied. Some nozzles were long, and some nozzles were short. We came up with a single engine design with variable nozzle extensions and configurations to fit particular vehicle locations. (See Slides 10 and 11, Appendix F)

17 CFR 232.310 - Marking changed material.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ASCII and HTML documents by inserting the tag before and the tag following a paragraph containing changed material. HTML documents may be marked to show changed materials within paragraphs. Financial...

Disulfide-Bridged (Mo3S11) Cluster Polymer: Molecular Dynamics and Application as Electrode Material for a Rechargeable Magnesium Battery.

PubMed

Truong, Quang Duc; Kempaiah Devaraju, Murukanahally; Nguyen, Duc N; Gambe, Yoshiyuki; Nayuki, Keiichiro; Sasaki, Yoshikazu; Tran, Phong D; Honma, Itaru

2016-09-14

Exploring novel electrode materials is critical for the development of a next-generation rechargeable magnesium battery with high volumetric capacity. Here, we showed that a distinct amorphous molybdenum sulfide, being a coordination polymer of disulfide-bridged (Mo3S11) clusters, has great potential as a rechargeable magnesium battery cathode. This material provided good reversible capacity, attributed to its unique structure with high flexibility and capability of deformation upon Mg insertion. Free-terminal disulfide moiety may act as the active site for reversible insertion and extraction of magnesium.

Fiber optic connector

DOEpatents

Rajic, S.; Muhs, J.D.

1996-10-22

A fiber optic connector and method for connecting composite materials within which optical fibers are imbedded are disclosed. The fiber optic connector includes a capillary tube for receiving optical fibers at opposing ends. The method involves inserting a first optical fiber into the capillary tube and imbedding the unit in the end of a softened composite material. The capillary tube is injected with a coupling medium which subsequently solidifies. The composite material is machined to a desired configuration. An external optical fiber is then inserted into the capillary tube after fluidizing the coupling medium, whereby the optical fibers are coupled. 3 figs.

A remote fuzzy multicriteria diagnosis of sore throat.

PubMed

Dalalah, Doraid; Magableh, Sami

2008-09-01

A sore throat (also known as pharyngitis or tonsillitis) is most commonly caused by a contagious viral infection (such as the flu, cold, or mononucleosis), although more serious throat infections can be caused by a bacterial infection (such as strep, mycoplasma, or Haemophilus). Bacterial sore throats respond well to antibiotics, whereas viral ones do not. However, strep throat remains a leading cause for physician visits, and researchers have long struggled to determine how best to treat it. The current practice guidelines offer different management options for adult patients presenting with a sore throat. Thus, when a physician treats a patient with acute pharyngitis, the clinical decision that usually needs to be made is whether the pharyngitis is attributable to group A streptococci. The key concern is the degree to which the clinical possibility of a group A streptococcal infection should affect clinician's decisions. To determine the best treatment of pharyngitis, we conducted a multicriteria decision analysis using fuzzy reasoning for remote health service delivery between a healthcare provider and patients. The approach can be adopted for interactive phone use or online system application. Five alternative treatment options were considered, particularly: (a) no test no Rx, (b) rapid strep, (c) culture, (d) rapid strep and culture, and (e) empiric Rx. Fuzzy reasoning is used to examine the signs/symptoms and their ratings. The study includes seven criteria factors that can be rated according to each alternative clinical treatment using linguistic statements. The model shows that no test no Rx is the best option for the cases of low prevalence of group A streptococcal infection. Two strategies--culture and treat if positive and rapid strep with culture of negative results--are equally preferable for patients with moderate prevalence likelihood. Rapid strep and culture of negative results is the best management strategy for patients with high population prevalence of group A streptococcal infection. In conclusion, the best clinical management of patients with sore throat depends on both the clinical probability of group A streptococcal infection and clinical judgments that incorporate the importance ratings of the individual patients as well as practice circumstances.

The sensitivity and the specifity of rapid antigen test in streptococcal upper respiratory tract infections.

PubMed

Gurol, Yesim; Akan, Hulya; Izbirak, Guldal; Tekkanat, Zuhal Tazegun; Gunduz, Tehlile Silem; Hayran, Osman; Yilmaz, Gulden

2010-06-01

It is aimed to detect the sensitivity and specificity of rapid antigen detection of group A beta hemolytic streptococci from throat specimen compared with throat culture. The other goal of the study is to help in giving clinical decisions in upper respiratory tract infections according to the age group, by detection of sensitivity and positive predictive values of the rapid tests and throat cultures. Rapid antigen detection and throat culture results for group A beta hemolytic streptococci from outpatients attending to our university hospital between the first of November 2005 and 31st of December 2008 were evaluated retrospectively. Throat samples were obtained by swabs from the throat and transported in the Stuart medium and Quickvue Strep A [Quidel, San Diego, USA] cassette test was applied and for culture, specimen was inoculated on 5% blood sheep agar and identified according to bacitracin and trimethoprim-sulphametaxazole susceptibility from beta hemolytic colonies. During the dates between the first of November 2005 and 31st of December 2008, from 453 patients both rapid antigen detection and throat culture were evaluated. Rapid antigen detection sensitivity and specificity were found to be 64.6% and 96.79%, respectively. The positive predictive value was 80.95% whereas negative predictive value was 92.82%. Kappa index was 0.91. When the results were evaluated according to the age groups, the sensitivity and the positive predictive value of rapid antigen detection in children were 70%, 90.3% and in adults 59.4%, 70.4%. When bacterial infection is concerned to prevent unnecessary antibiotic use, rapid streptococcal antigen test (RSAT) is a reliable method to begin immediate treatment. To get the maximum sensitivity of RSAT, the specimen collection technique used and education of the health care workers is important. While giving clinical decision, it must be taken into consideration that the sensitivity and the positive predictive value of the RSAT is quite lower in adult age group than in pediatric age group. Copyright (c) 2010 Elsevier Ireland Ltd. All rights reserved.

Resonant Transmission of Air-Coupled Ultrasound Through Metallic Inserts in Honeycomb Sandwich Structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, J.J.; Barnard, D.J.; Hsu, D.K.

2005-04-09

Metallic inserts are embedded into composite honeycomb sandwiches as hard points for mechanical connections. Air-coupled ultrasound can be used for detecting disbonds between the insert and the facesheet. It was discovered in such inspections that a surprisingly large amplitude could be transmitted through thick metallic inserts (e.g. 0.75'' thick and 1.5'' diameter), whereas a thin plate of the same material will transmit a much weaker signal. This paper reports an experimental and analytic study of the geometrical effect of inserts on transmitted UT signals. Modal analyses of cylindrical inserts were made using the finite element code ANSYS. The transmission efficiencymore » or air-coupled ultrasound correlated well with the longitudinal vibration mode of the cylinder.« less

Electrical connector composite housing and method of making same

DOEpatents

Silva, Frank A.

1979-01-01

A sleeve-like insert of conductive elastomeric material of a type which serves as an internal shield in electrical connectors for connecting high voltage cables has an end portion folded upon itself, the enfolded portion being substantially permanently retained in its desired position by allowing insulative elastomeric material to fill apertures in the end portion and become bonded thereto in a void free manner, during molding of an insulating outer sleeve-like jacket about the insert.

Low Cost, Net Shape Fabrication of Rhenium and High Temperature Materials for Rocket Engine Components

DTIC Science & Technology

2001-03-01

tungsten thin wall nozzle liner removed from reusable mandrel. b) W and Re rocket, nozzle inserts (2 inserts per mandrel) for Air Force. Rhenium PPI...compares the fabrication time for the VPS nozzles with equivalent carbon / carbon composite (C/C) and forged tungsten materials. Table 5: Comparison of...UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADPO1 1181 TITLE: Low Cost, Net Shape Fabrication of Rhenium and High

Two lozenges containing benzocaine assessed in the relief of sore throat.

PubMed

Kagan, G; Huddlestone, L; Wolstencroft, P

1982-01-01

A study has been conducted in general practice comparing two brands of lozenges, Merocaine (Merrell) and Tyrozets, (M.S.D.), in the management of acute sore throat and pharyngitis. Eighty-eight patients entered the between-patient study and each completed a diary card covering symptoms experienced and dosage used for each of the two drugs. The doctor reported upon the appearance of the throat and added antibiotics in cases of necessity, which was approximately for one-third of patients. Merocaine proved to be significantly superior to Tyrozets in producing rapid pain relief (within 15 minutes) and reduction of faucial and pharyngeal injection.

Multi-Day Air Saturation at 20 and 22 FSW With Direct Ascent: Data Report on Project 92-09

DTIC Science & Technology

2002-03-01

0802 0 air L/S; Divers 7, 8, 9, 10, 11, 12 0803 22 air R/B Feb 09 1919 22 air DMO entry, Diver 12 has scratchy throat and post-nasal drip, given aspirin...10,11, fsw 12 _ Galley is shipshape as is food. 1919 8 OK Robinson 12 describes scratchy throat & post nasal drip with ????? with purulent nasal...Ball 12 scratchy throat , sniffles, ASA 2 PO every 4 hrs 9 no c/o 7 no c/o 10 no c/o 11 mild congestion, Sudafed 60 mg Divers in good spirits 1250 8

Detection of strep throat causing bacterium directly from medical swabs by touch spray-mass spectrometry.

PubMed

Jarmusch, Alan K; Pirro, Valentina; Kerian, Kevin S; Cooks, R Graham

2014-10-07

Strep throat causing Streptococcus pyogenes was detected in vitro and in simulated clinical samples by performing touch spray ionization-mass spectrometry. MS analysis took only seconds to reveal characteristic bacterial and human lipids. Medical swabs were used as the substrate for ambient ionization. This work constitutes the initial step in developing a non-invasive MS-based test for clinical diagnosis of strep throat. It is limited to the single species, S. pyogenes, which is responsible for the vast majority of cases. The method is complementary to and, with further testing, a potential alternative to current methods of point-of-care detection of S. pyogenes.

Possible behavioural, energetic and demographic effects of displacement of red-throated divers

USGS Publications Warehouse

Dierschke, Volker; Furness, Robert W.; Gray, Carrie E.; Petersen, Ib Krag; Schmutz, Joel A.; Zydelis, Ramunas; Daunt, Francis

2017-01-01

This report comprises the main points of discussion and agreement during a workshop, held in Edinburgh in May 2017, to discuss how displacement might affect individuals and the Red-throated diver population; with additional information added by the scientists following the workshop.

Achievable accuracy of hip screw holding power estimation by insertion torque measurement.

PubMed

Erani, Paolo; Baleani, Massimiliano

2018-02-01

To ensure stability of proximal femoral fractures, the hip screw must firmly engage into the femoral head. Some studies suggested that screw holding power into trabecular bone could be evaluated, intraoperatively, through measurement of screw insertion torque. However, those studies used synthetic bone, instead of trabecular bone, as host material or they did not evaluate accuracy of predictions. We determined prediction accuracy, also assessing the impact of screw design and host material. We measured, under highly-repeatable experimental conditions, disregarding clinical procedure complexities, insertion torque and pullout strength of four screw designs, both in 120 synthetic and 80 trabecular bone specimens of variable density. For both host materials, we calculated the root-mean-square error and the mean-absolute-percentage error of predictions based on the best fitting model of torque-pullout data, in both single-screw and merged dataset. Predictions based on screw-specific regression models were the most accurate. Host material impacts on prediction accuracy: the replacement of synthetic with trabecular bone decreased both root-mean-square errors, from 0.54 ÷ 0.76 kN to 0.21 ÷ 0.40 kN, and mean-absolute-percentage errors, from 14 ÷ 21% to 10 ÷ 12%. However, holding power predicted on low insertion torque remained inaccurate, with errors up to 40% for torques below 1 Nm. In poor-quality trabecular bone, tissue inhomogeneities likely affect pullout strength and insertion torque to different extents, limiting the predictive power of the latter. This bias decreases when the screw engages good-quality bone. Under this condition, predictions become more accurate although this result must be confirmed by close in-vitro simulation of the clinical procedure. Copyright © 2018 Elsevier Ltd. All rights reserved.

Investigating the Evolution of Progressive Die Wear on Uncoated Dp1180 Steel in Production Environment

NASA Astrophysics Data System (ADS)

Wu, W.; Zhou, D. J.; Adamski, D. J.; Young, D.; Wang, Y. W.

2017-09-01

A study of die wear was performed using an uncoated dual phase, 1,180 MPa ultimate tensile strength steel (DP1180) in a progressive die. The objectives of the current study are to evaluate the die durability of various tooling materials and coatings for forming operations on uncoated DP1180 steel and update OEM’s die standards based on the experimental results in the real production environment. In total, 100,800 hits were performed in manufacturing production conditions, where 33 die inserts with the combination of 10 die materials and 9 coatings were investigated. The die inserts were evaluated for surface wear using scanning electron microscopy and characterized in terms of die material and/or coating defects, failure mode, failure initiation and propagation. Surface roughness of the formed parts was characterized using a WYKO NT110 machine. The analytical analysis of the die inserts and formed parts, combined with the failure mode and service life, provide a basis for die material and coating selection for forming AHSS components. The conclusions of this study will guide the selection of die material and coatings for high-volume production of AHSS components.

Eye, nose, hair, and throat: external anatomy of the head of a neonate gray whale (Cetacea, Mysticeti, Eschrichtiidae).

PubMed

Berta, Annalisa; Ekdale, Eric G; Zellmer, Nicholas T; Deméré, Thomas A; Kienle, Sarah S; Smallcomb, Meghan

2015-04-01

Information is scarce on gray whale (Eschrichtius robustus) anatomy and that of mysticetes in general. Dissection of the head of a neonatal gray whale revealed novel anatomical details of the eye, blowhole, incisive papilla with associated nasopalatine ducts, sensory hairs, and throat grooves. Compared to a similar sized right whale calf, the gray whale eyeball is nearly twice as long. The nasal cartilages of the gray whale, located between the blowholes, differ from the bowhead in having accessory cartilages. A small, fleshy incisive papilla bordered by two blind nasopalatine pits near the palate's rostral tip, previously undescribed in gray whales, may be associated with the vomeronasal organ, although histological evidence is needed for definitive identification. Less well known among mysticetes are the numerous elongated, stiff sensory hairs (vibrissae) observed on the gray whale rostrum from the ventral tip to the blowhole and on the mandible. These hairs are concentrated on the chin, and those on the lower jaw are arranged in a V-shaped pattern. We confirm the presence of two primary, anteriorly converging throat grooves, confined to the throat region similar to those of ziphiid and physeteroid odontocetes. A third, shorter groove occurs lateral to the left primary groove. The throat grooves in the gray whale have been implicated in gular expansion during suction feeding. © 2015 Wiley Periodicals, Inc.

The impact of recurrent throat infection on children and their families.

PubMed

Howel, Denise; Webster, Simon; Hayes, Jane; Barton, Andrew; Donaldson, Liam

2002-06-01

Recurrent throat problems in children are common and have an impact on the family. The appropriateness of surgery will depend on both clinical and social factors. The aim of this study was to assess the impact on the whole family when a child is suffering from recurrent throat problems, and investigate related parental attitudes. A total of 1190 parents of children in northern England for whom tonsillectomy or adeno-tonsillectomy was a possible treatment option were sent a questionnaire covering social and clinical issues such as children's symptoms, the impact on family life and parental attitudes. The majority of children had experienced more than four episodes in the previous year, had their sleep affected and time off school. Most parents were worried and reported disruption to the family, including taking time off work and cross-infection. Parental disruption, worry and eagerness for surgery were significantly associated with the duration of episodes of throat problems and the number of episodes in the previous year, but not with duration of tonsillitis. Time off school, or parental time off work was significantly associated with parental worry and disruption, but not with eagerness for surgery. This work highlights the impact of recurrent throat problems and related parental attitudes, and will aid in striking a balance between clinical requirements and the needs and wishes of the family.

Usefulness of Leukocyte Esterase Test Versus Rapid Strep Test for Diagnosis of Acute Strep Pharyngitis.

PubMed

Nibhanipudi, Kumara V

2015-01-01

A study to compare the usage of throat swab testing for leukocyte esterase on a test strip(urine dip stick-multi stick) to rapid strep test for rapid diagnosis of Group A Beta hemolytic streptococci in cases of acute pharyngitis in children. The testing of throat swab for leukocyte esterase on test strip currently used for urine testing may be used to detect throat infection and might be as useful as rapid strep. All patients who come with a complaint of sore throat and fever were examined clinically for erythema of pharynx, tonsils and also for any exudates. Informed consent was obtained from the parents and assent from the subjects. 3 swabs were taken from pharyngo-tonsillar region, testing for culture, rapid strep & Leukocyte Esterase. Total number is 100. Cultures 9(+); for rapid strep== 84(-) and16 (+); For LE== 80(-) and 20(+) From data configuration Rapid Strep versus LE test don't seem to be a random (independent) assignment but extremely aligned. The Statistical results show rapid and LE show very agreeable results. Calculated Value of Chi Squared Exceeds Tabulated under 1 Degree Of Freedom (P<.0.0001) reject Null HYPOTHESIS and Conclude Alternative Conclusions: Leukocyte esterase on throat swab is as useful as rapid strep test for rapid diagnosis of strep pharyngitis on test strip currently used for urine dip stick causing acute pharyngitis in children.

A tandem mirror hybrid plume plasma propulsion facility

NASA Technical Reports Server (NTRS)

Yang, T. F.; Krueger, W. A.; Peng, S.; Urbahn, J.; Chang-Diaz, F. R.

1988-01-01

This paper discusses a novel concept in electrodeless plasma propulsion, in which the materials problems are ameliorated by an electrodeless magnetic confinement scheme borrowed from the tandem mirror approach to controlled thermonuclear fusion. The concept also features a two-stage magnetic nozzle with an annular hypersonic coaxial gas injector near the throat. The nozzle produces hybrid plume by the coaxial injection of hypersonic neutral gas, and the gas layer thus formed protects the material walls from the hot plasma and, through increased collisions, helps detach it from the diverging magnetic field. The tandem mirror plasma propulsion facility is capable of delivering a variable I(sp). The results of numerical simulation of this concept are presented together with those from an experimental tandem-mirror plasma propulsion device.

ITO-TiN-ITO Sandwiches for Near-Infrared Plasmonic Materials.

PubMed

Chen, Chaonan; Wang, Zhewei; Wu, Ke; Chong, Haining; Xu, Zemin; Ye, Hui

2018-05-02

Indium tin oxide (ITO)-based sandwich structures with the insertion of ultrathin (<10 nm) titanium nitride (TiN) are investigated as near-infrared (NIR) plasmonic materials. The structural, electrical, and optical properties reveal the improvement of the sandwich structures stemmed from TiN insertion. TiN is a well-established alternative to noble metals such as gold, elevating the electron conductivity of sandwich structures as its thickness increases. Dielectric permittivities of TiN and top ITO layers show TiN-thickness-dependent properties, which lead to moderate and tunable effective permittivities for the sandwiches. The surface plasmon polaritons (SPP) of the ITO-TiN-ITO sandwich at the telecommunication window (1480-1570 nm) are activated by prism coupling using Kretschmann configuration. Compared with pure ITO films or sandwiches with metal insertion, the reflectivity dip for sandwiches with TiN is relatively deeper and wider, indicating the enhanced coupling ability in plasmonic materials for telecommunications. The SPP spatial profile, penetration depth, and degree of confinement, as well as the quality factors, demonstrate the applicability of such sandwiches for NIR plasmonic materials in various devices.

A familial {open_quotes}balanced{close_quotes} 3;9 translocation with cryptic 8q insertion leading to deletion and duplication of 9p23 loci in siblings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagstaff, J.; Hemann, M.

1995-01-01

A child with phenotypic features of the 9p{sup {minus}} syndrome, including metopic craniosynostosis, small ears, abdominal wall defect, and mental retardation, as well as hypopigmentation, was found to have a cytogenetically balanced 3;9 translocation, with breakpoints at 3p11 and 9p23, inherited from his phenotypically normal father. Molecular analysis showed heterozygous deletion of the TYRP (tyrosinase-related protein) locus, as well as loci D9S157, D9S274, D9S268, and D9S267, in the child but in neither parent. FISH analysis of the proband`s father indicated that loci deleted in his son, including TYRP, were present on neither the der(3) nor the der(9) translocation products butmore » had been inserted into the long arm of chromosome 8. Therefore, the apparent deletion of these loci in the proband was the result of meiotic segregation of the father`s 3;9 translocation chromosomes together with his normal chromosome 8 (not bearing the insertion from 9p23). Neither the deletion of these 9p23 loci from the translocation chromosomes nor their insertion into 8q was detectable by standard chromosome banding techniques. The proband`s sister exhibited speech delay, mild facial dysmorphism, and renal malformation, and her karyotype was 46,XX. Molecular analysis showed that she had inherited normal chromosomes 3 and 9, as well as the chromosome 8 with the insertion of 9p23 material, from her father. This analysis illustrates a new mechanism to explain cases in which an apparently balanced translocation has been transmitted from a normal parent to a child with a phenotypic abnormality: submicroscopic deletion of material from the translocation breakpoint and insertion into a third chromosome in the balanced parent, with meiotic segregation leading to loss of the inserted material in the child. 36 refs., 9 figs., 1 tab.« less

Effect of Different Composite Restorations on the Cuspal Deflection of Premolars Restored with Different Insertion Techniques- An In vitro Study.

PubMed

Singhal, Sakshi; Gurtu, Anuraag; Singhal, Anurag; Bansal, Rashmi; Mohan, Sumit

2017-08-01

This study was conducted to assess the effect of different composite materials on the cuspal deflection of premolars restored with bulk placement of resin composite in comparison to horizontal incremental placement and modified tangential incremental placement. The aim of this study was to evaluate the cuspal deflection caused by different composite materials when different insertion techniques were used. Two different composite materials were used that is Tetric N Ceram (Ivoclar Vivadent marketing, India) and SonicFill TM (Kerr Sybron Dental). Forty standardized Mesio-Occluso-Distal (MOD) preparations were prepared on maxillary first premolars. Each group was divided according to composite insertion technique (n=10), as follows: Group I - bulk insertion using Tetric N Ceram, Group II - Horizontal incremental insertion technique using Tetric N Ceram, Group III- Modified tangential incremental technique using Tetric N Ceram, and Group IV- bulk insertion using SonicFill TM . Preparations were acid-etched, and bonded with adhesive resin to provide micro mechanical attachment before restoration using a uniform etching and bonding protocol in all the groups. All groups received the same total photo-polymerization time. Cuspal deflection was measured during the restorative procedure using customized digital micrometer assembly. One-way ANOVA test was applied for the analysis of significant difference between the groups, p-value less than 0.05 was considered statistically significant. The average cuspal deflections for the different groups were as follows: Group I 0.045±0.018, Group II 0.029±0.009, Group III 0.018±0.005 and Group IV 0.017±0.004. The intergroup comparison revealed statistically significant difference. A measurable amount of cuspal deflection was present in all the four studied groups. In general, bulkfill restoration technique with conventional composite showed significantly highest cusp deflection. There were no significant differences in cuspal deflection among sonicFill TM and modified tangential incremental insertion techniques.

MTR MAIN FLOOR. MEN DEMONSTRATE INSERTION OF DUMMY PLUG INTO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR MAIN FLOOR. MEN DEMONSTRATE INSERTION OF DUMMY PLUG INTO AN MTR BEAM HOLE. ONE MAN CHECKS RADIATION LEVEL AT THE END OF THE UNIVERSAL COFFIN, WHILE ANOTHER USES TOOL TO INSERT PLUG INTO HOLE THROUGH COFFIN. MEN WEAR "ANTI-C" (ANTI-CONTAMINATION) CLOTHING. INL NEGATIVE NO. 6198. R.G. Larsen, Photographer, 6/27/1952 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Long lifetime hollow cathodes for 30-cm mercury ion thrusters

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Kerslake, W. R.

1976-01-01

An experimental investigation of hollow cathodes for 30-cm Hg bombardment thrusters was carried out. Both main and neutralizer cathode configurations were tested with both rolled foil inserts coated with low work function material and impregnated porous tungsten inserts. Temperature measurements of an impregnated insert at various positions in the cathode were made. These, along with the cathode thermal profile are presented. A theory for rolled foil and impregnated insert operation and lifetime in hollow cathodes is developed. Several endurance tests, as long as 18000 hours at emission currents of up to 12 amps were attained with no degradation in performance.

Sequential cooling insert for turbine stator vane

DOEpatents

Jones, Russell B.; Krueger, Judson J.; Plank, William L.

2014-04-01

A sequential impingement cooling insert for a turbine stator vane that forms a double impingement for the pressure and suction sides of the vane or a triple impingement. The insert is formed from a sheet metal formed in a zigzag shape that forms a series of alternating impingement cooling channels with return air channels, where pressure side and suction side impingement cooling plates are secured over the zigzag shaped main piece. Another embodiment includes the insert formed from one or two blocks of material in which the impingement channels and return air channels are machined into each block.

Sequential cooling insert for turbine stator vane

DOEpatents

Jones, Russel B; Krueger, Judson J; Plank, William L

2014-11-04

A sequential impingement cooling insert for a turbine stator vane that forms a double impingement for the pressure and suction sides of the vane or a triple impingement. The insert is formed from a sheet metal formed in a zigzag shape that forms a series of alternating impingement cooling channels with return air channels, where pressure side and suction side impingement cooling plates are secured over the zigzag shaped main piece. Another embodiment includes the insert formed from one or two blocks of material in which the impingement channels and return air channels are machined into each block.

21 CFR 874.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., and throat devices intended for human use that are in commercial distribution. (b) The identification..., nose, and throat device that has two or more types of uses (e.g., used both as a diagnostic device and...) Guidance documents referenced in this part are available on the Internet at http://www.fda.gov/cdrh...

Tuvan Throat Singing and Harmonics

ERIC Educational Resources Information Center

Ruiz, Michael J.; Wilken, David

2018-01-01

Tuvan throat singing, also called overtone singing, provides for an exotic demonstration of the physics of harmonics as well as introducing an Asian musical aesthetic. A low fundamental is sung and the singer skillfully alters the resonances of the vocal system to enhance an overtone (harmonic above the fundamental). The result is that the…

Trying Not to "Shove Religion down Their Throats"

ERIC Educational Resources Information Center

King, Jason

2015-01-01

This article attempts two tasks. First, to clarify how the claim that colleges and universities may "shove religion down students' throats" has a historical background. Second, to indicate how pedagogical strategies--like service learning, discussions, paper revisions, and "Just in Time Teaching" exercises--can be used in ways…

The Symptomatic Persian Gulf Veterans Protocol: An Analysis of Risk Factors with an Immunologic and Neuropsychiatric Assessment.

DTIC Science & Technology

1999-01-01

Evaluation of peripheral blood mononuclear cells, urine and throat cultures samples for the presence of mycoplasma or ureaplasma organisms by...c) by PCR with a universal mycoplasma primer. Mycoplasma or ureaplasma were detected frequently in urine and throat swabs, however no significant

Professional Implications of the Expansion of Retail-Based Clinics into Community Pharmacies

DTIC Science & Technology

2007-01-25

Common Illnesses Allergies (ages 6+), Bronchitis (ages 10-64), Ear Infections, Pink Eye and Styes, $49 & Strep Throat Bladder Infections (females...ages 12-64) & $59 Strep Throat Skin Conditions Athletes Foot, Cold Sores, Deer Tick Bite, Impetigo, Minor Bums & Rashes, $49 Minor Skin Infection, Poison

Modeling the Insertion Mechanics of Flexible Neural Probes Coated with Sacrificial Polymers for Optimizing Probe Design

PubMed Central

Singh, Sagar; Lo, Meng-Chen; Damodaran, Vinod B.; Kaplan, Hilton M.; Kohn, Joachim; Zahn, Jeffrey D.; Shreiber, David I.

2016-01-01

Single-unit recording neural probes have significant advantages towards improving signal-to-noise ratio and specificity for signal acquisition in brain-to-computer interface devices. Long-term effectiveness is unfortunately limited by the chronic injury response, which has been linked to the mechanical mismatch between rigid probes and compliant brain tissue. Small, flexible microelectrodes may overcome this limitation, but insertion of these probes without buckling requires supporting elements such as a stiff coating with a biodegradable polymer. For these coated probes, there is a design trade-off between the potential for successful insertion into brain tissue and the degree of trauma generated by the insertion. The objective of this study was to develop and validate a finite element model (FEM) to simulate insertion of coated neural probes of varying dimensions and material properties into brain tissue. Simulations were performed to predict the buckling and insertion forces during insertion of coated probes into a tissue phantom with material properties of brain. The simulations were validated with parallel experimental studies where probes were inserted into agarose tissue phantom, ex vivo chick embryonic brain tissue, and ex vivo rat brain tissue. Experiments were performed with uncoated copper wire and both uncoated and coated SU-8 photoresist and Parylene C probes. Model predictions were found to strongly agree with experimental results (<10% error). The ratio of the predicted buckling force-to-predicted insertion force, where a value greater than one would ideally be expected to result in successful insertion, was plotted against the actual success rate from experiments. A sigmoidal relationship was observed, with a ratio of 1.35 corresponding to equal probability of insertion and failure, and a ratio of 3.5 corresponding to a 100% success rate. This ratio was dubbed the “safety factor”, as it indicated the degree to which the coating should be over-designed to ensure successful insertion. Probability color maps were generated to visually compare the influence of design parameters. Statistical metrics derived from the color maps and multi-variable regression analysis confirmed that coating thickness and probe length were the most important features in influencing insertion potential. The model also revealed the effects of manufacturing flaws on insertion potential. PMID:26959021

Effectiveness of nurse-led clinics on service delivery and clinical outcomes in adults with chronic ear, nose and throat complaints: a systematic review.

PubMed

Whiteford, Caroline; White, Sarahlouise; Stephenson, Matthew

2016-04-01

Ear, nose and throat complaints are very common and can cause significant disruption to patients' lives. Many conditions are of a chronic nature and are not currently managed in a timely manner by general practitioners in the community. This may be due to a lack of specialized knowledge, necessary diagnostic equipment or time for lengthy patient education on management of their condition. A nurse-led model of care may be an effective alternative. To examine the effectiveness of nurse-led clinics on adults with chronic ear, nose and throat complaints. Adult patients, aged 18 years and older, attending ear, nose and throat clinics, regardless of the complaint. Nurse-led care in general practice and acute care in which the nurse was identified as taking a lead role in the care of the patients with chronic ear, nose and throat complaints. General practitioner-led care, or ear, nose and throat consultant-led care, sometimes described as "standard care". Service delivery outcomes, clinical and health outcomes and financial outcomes. Any relevant quantitative studies published in English between 1980 and 2013 were considered. A standardized three-step search strategy aimed to find both published and unpublished studies. Databases searched include PubMed, CINAHL, Cochrane Library (CENTRAL), Scopus, Embase, MedNar and ProQuest Theses and Dissertations. Methodological validity was assessed independently by two reviewers using standardized critical appraisal instruments from the Joanna Briggs Institute. Due to methodological heterogeneity of the included studies, no statistical pooling was possible and all results are presented narratively. The search identified 13,536 titles, of which 20 potentially relevant articles were retrieved. Of these 20, 17 were excluded following full-text review leaving three studies that were assessed for methodological quality and included in the review. Service delivery outcome findings were that patient satisfaction was equal or higher and waiting times were shorter in nurse led clinics. The other service delivery outcomes were not addressed. Clinical and health outcomes findings were that lower pain/discomfort levels were demonstrated in nurse led clinics but other clinical/health outcomes were not addressed. Financial outcomes findings were that nurse-led clinics were cost effective when compared with medical-led clinics. While all studies reported evidence of the effectiveness of nurse-led clinics in service delivery and clinical outcomes in adults with chronic ear, nose and throat complaints, most of the data was self-reported and many of the outcomes of interest were not considered. The lack of experimental trials means that the level of evidence is low and further research is needed. There was also not enough detail in the financial outcomes from which clear conclusions of the cost benefit of nurse-led clinics could be drawn. Evidence from included studies indicated higher levels of patient satisfaction, cost benefits and lower levels of pain/discomfort in nurse-led clinics, which suggests that nurse-led ear, nose and throat clinics may be considered in the management of adult patients with ear, nose and throat complaints. Currently there is little evidence examining the effectiveness of nurse-led ear, nose and throat clinics. Areas to be addressed by future research should include: levels of patient education, booking queues, levels of self-treatment change in presentation to clinic episodes, reinfection rates, prevention and cure and representation of patients at clinics for same complaint.

Cutting holes in fabric-faced panels

NASA Technical Reports Server (NTRS)

Peterson, S. A.

1981-01-01

Tool has 2 carbide inserts that bore clean holes through fibrous material with knifelike slicing action. Cutting edge of insert is curved, with plane inner surface at 30 degree angle to tool axis. Drill press or hand-held drill can be used to hold cutting tool.

Pop tests of storable biopropellant liquid apogee engine

NASA Astrophysics Data System (ADS)

Kuroda, Yukio; Tadano, Makoto; Sato, Masahiro; Kusaka, Kazuo; Kobayashi, Hideyuki; Iihara, Sigeyasu; Ban, Hiroyuki

1994-10-01

A pressure-fed, blowdown, hydrazine/NTO apogee propulsion system had been selected for the ETS-6. One of the problems encountered during the development of the engine was the occurrence of pops (popping) at the higher operating chamber pressures. Pops are irregular high amplitude pressure pulses. It is generally agreed that pops is a liquid spray/gas two-phase explosion triggered by a local explosion near the jet impingement region. The effects of operating parameters on pops observed in the development tests of the apogee engine for the ETS-6 were inconsistent with those reported earlier for single impingement injectors; pops with the apogee engine injectors was more likely to occur at higher chamber pressures, higher injection velocities, and higher propellant temperatures. Pops data were correlated fairly well in chamber pressures (bar-P(sub c)) vs. fuel Reynolds number (R(sub ef)) plane. However, the range of operating parameters for the above correlation were very narrow since they were obtained during injector screening tests for a particular application to the apogee engine. It was also felt that the above correlation was too simplistic to capture any effect of design parameters of multi-element injectors. In the present study, the demarcation between pops and the pops-free region was determined in broader operating ranges and design parameters. The range of bar-P(sub c) and R(sub ef) was extended by exchanging graphite nozzle throat inserts with different throat diameters. The injectors were carefully selected to obtain effects, if any, of (1) film cooling fraction, (2) secondary mixing, and (3) number of elements and/or fuel orifice diameters. It was found that there was a threshold fuel Reynolds number below which no pops were observed at any chamber pressures and that the pops region curve in the bar-P(sub c)-R(sub ef) plane had two branches: upper branches and lower branches.

Seal welded cast iron nuclear waste container

DOEpatents

Filippi, Arthur M.; Sprecace, Richard P.

1987-01-01

This invention identifies methods and articles designed to circumvent metallurgical problems associated with hermetically closing an all cast iron nuclear waste package by welding. It involves welding nickel-carbon alloy inserts which are bonded to the mating plug and main body components of the package. The welding inserts might be bonded in place during casting of the package components. When the waste package closure weld is made, the most severe thermal effects of the process are restricted to the nickel-carbon insert material which is far better able to accommodate them than is cast iron. Use of nickel-carbon weld inserts should eliminate any need for pre-weld and post-weld heat treatments which are a problem to apply to nuclear waste packages. Although the waste package closure weld approach described results in a dissimilar metal combination, the relative surface area of nickel-to-iron, their electrochemical relationship, and the presence of graphite in both materials will act to prevent any galvanic corrosion problem.

Electron-rich driven electrochemical solid-state amorphization in Li-Si alloys.

PubMed

Wang, Zhiguo; Gu, Meng; Zhou, Yungang; Zu, Xiaotao; Connell, Justin G; Xiao, Jie; Perea, Daniel; Lauhon, Lincoln J; Bang, Junhyeok; Zhang, Shengbai; Wang, Chongmin; Gao, Fei

2013-09-11

The physical and chemical behaviors of materials used in energy storage devices, such as lithium-ion batteries (LIBs), are mainly controlled by an electrochemical process, which normally involves insertion/extraction of ions into/from a host lattice with a concurrent flow of electrons to compensate charge balance. The fundamental physics and chemistry governing the behavior of materials in response to the ions insertion/extraction is not known. Herein, a combination of in situ lithiation experiments and large-scale ab initio molecular dynamics simulations are performed to explore the mechanisms of the electrochemically driven solid-state amorphization in Li-Si systems. We find that local electron-rich condition governs the electrochemically driven solid-state amorphization of Li-Si alloys. This discovery provides the fundamental explanation of why lithium insertion in semiconductor and insulators leads to amorphization, whereas in metals, it leads to a crystalline alloy. The present work correlates electrochemically driven reactions with ion insertion, electron transfer, lattice stability, and phase equilibrium.

Electron-Rich Driven Electrochemical Solid-State Amorphization in Li-Si Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhiguo; Gu, Meng; Zhou, Yungang

2013-08-14

The physical and chemical behaviors of materials used in energy storage devices, such as lithium-ion batteries (LIBs), are mainly controlled by an electrochemical process, which normally involves insertion/extraction of ions into/from a host lattice with a concurrent flow of electrons to compensate charge balance. The fundamental physics and chemistry governing the behavior of materials in response to the ions insertion/extraction is not known. Herein, a combination of in situ lithiation experiments and large-scale ab initio molecular dynamics simulations are performed to explore the mechanisms of the electrochemically driven solid-state amorphization in Li-Si systems. We find that local electron-rich condition governsmore » the electrochemically driven solid-state amorphization of Li-Si alloys. This discovery provides the fundamental explanation of why lithium insertion in semiconductor and insulators leads to amorphization, whereas in metals, it leads to a crystalline alloy. The present work correlates electrochemically driven reactions with ion insertion, electron transfer, lattice stability and phase equilibrium.« less

Outbreak of pyogenic abscesses after diphtheria and tetanus toxoids and pertussis vaccination.

PubMed

Simon, P A; Chen, R T; Elliott, J A; Schwartz, B

1993-05-01

Nine children who received diphtheria and tetanus toxoids and pertussis vaccine from the same vial at a clinic in Colorado developed pyogenic abscesses at the site of injection. Eight abscesses required surgical drainage and five children were hospitalized. Group A Streptococcus (GAS) was cultured from eight wounds and Staphylococcus aureus was also isolated from four. Epidemiologic investigation revealed that within the hour of the first child's vaccination, three children had been diagnosed in the clinic with GAS pharyngitis. GAS recovered from repeat throat swabs from two of these children and the eight case-isolates were all serotype M-12, T-12 and had identical immunoblot patterns on sodium dodecyl sulfate-polyacrylamide gel electrophoresis. Laboratory simulation studies demonstrated that GAS can survive for at least 4 days on the external surface of a vaccine vial rubber stopper and contaminate needles inserted through the stopper. Swabbing the stopper with 70% isopropyl alcohol resulted in effective disinfection. To prevent potential contamination meticulous attention to sterile technique is important when withdrawing vaccine from multidose vaccine vials.

A Comparison of Combustion Dynamics for Multiple 7-Point Lean Direct Injection Combustor Configurations

NASA Technical Reports Server (NTRS)

Tacina, K. M.; Hicks, Y. R.

2017-01-01

The combustion dynamics of multiple 7-point lean direct injection (LDI) combustor configurations are compared. LDI is a fuel-lean combustor concept for aero gas turbine engines in which multiple small fuel-air mixers replace one traditionally-sized fuel-air mixer. This 7-point LDI configuration has a circular cross section, with a center (pilot) fuel-air mixer surrounded by six outer (main) fuel-air mixers. Each fuel-air mixer consists of an axial air swirler followed by a converging-diverging venturi. A simplex fuel injector is inserted through the center of the air swirler, with the fuel injector tip located near the venturi throat. All 7 fuel-air mixers are identical except for the swirler blade angle, which varies with the configuration. Testing was done in a 5-atm flame tube with inlet air temperatures from 600 to 800 F and equivalence ratios from 0.4 to 0.7. Combustion dynamics were measured using a cooled PCB pressure transducer flush-mounted in the wall of the combustor test section.

Tool wear mechanisms in turning titanium-aluminum-vanadium using tungsten carbide and polycrystalline diamond inserts

NASA Astrophysics Data System (ADS)

Schrock, David James

The objective of this work is to identify some of the tool wear mechanisms at the material level for the machining of titanium and to provide some understanding of these mechanisms for use in physics based tool wear models. Turning experiments were conducted at cutting speeds of 61m/min, 91m/min, and 122m/min on Ti-6Al-4V, an alloy of titanium, using two different grades of tungsten carbide cutting inserts and one grade of polycrystalline diamond inserts. Three-dimensional wear data and two-dimensional wear profiles of the rake face were generated using Confocal Laser Scanning Microscopy to quantify the tool wear mechanisms. Additionally, the microstructure of the deformed work material (chip) and un-deformed parent material (work piece) were studied using Orientation Imaging Microscopy (OIM). Observations from tool wear studies on the PCD inserts revealed the presence of two fundamentally different wear mechanisms operating at the different cutting speeds. Microstructural analyses of the chip and the work material showed phase dependent tool wear mechanisms for machining titanium. There is a high likelihood of phase change occurring in the work material during machining, with a transformation from the alpha phase to the beta phase. The observed dramatic increase in wear is attributed to a combination of increased diffusivity in the beta phase of the titanium alloy in conjunction with a higher degree of recrystallization of the prior beta phase upon cooling. Results of other observations such as the influence of carbide grain size on tool wear are also discussed.

Dynamic analysis of a needle insertion for soft materials: Arbitrary Lagrangian-Eulerian-based three-dimensional finite element analysis.

PubMed

Yamaguchi, Satoshi; Tsutsui, Kihei; Satake, Koji; Morikawa, Shigehiro; Shirai, Yoshiaki; Tanaka, Hiromi T

2014-10-01

Our goal was to develop a three-dimensional finite element model that enables dynamic analysis of needle insertion for soft materials. To demonstrate large deformation and fracture, we used the arbitrary Lagrangian-Eulerian (ALE) method for fluid analysis. We performed ALE-based finite element analysis for 3% agar gel and three types of copper needle with bevel tips. To evaluate simulation results, we compared the needle deflection and insertion force with corresponding experimental results acquired with a uniaxial manipulator. We studied the shear stress distribution of agar gel on various time scales. For 30°, 45°, and 60°, differences in deflections of each needle between both sets of results were 2.424, 2.981, and 3.737mm, respectively. For the insertion force, there was no significant difference for mismatching area error (p<0.05) between simulation and experimental results. Our results have the potential to be a stepping stone to develop pre-operative surgical planning to estimate an optimal needle insertion path for MR image-guided microwave coagulation therapy and for analyzing large deformation and fracture in biological tissues. Copyright © 2014 Elsevier Ltd. All rights reserved.

An effective method to screen sodium-based layered materials for sodium ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Xu; Zhang, Zihe; Yao, Sai; Chen, An; Zhao, Xudong; Zhou, Zhen

2018-03-01

Due to the high cost and insufficient resource of lithium, sodium-ion batteries are widely investigated for large-scale applications. Typically, insertion-type materials possess better cyclic stability than alloy-type and conversion-type ones. Therefore, in this work, we proposed a facile and effective method to screen sodium-based layered materials based on Materials Project database as potential candidate insertion-type materials for sodium ion batteries. The obtained Na-based layered materials contains 38 kinds of space group, which reveals that the credibility of our screening approach would not be affected by the space group. Then, some important indexes of the representative materials, including the average voltage, volume change and sodium ion mobility, were further studied by means of density functional theory computations. Some materials with extremely low volume changes and Na diffusion barriers are promising candidates for sodium ion batteries. We believe that our classification algorithm could also be used to search for other alkali and multivalent ion-based layered materials, to accelerate the development of battery materials.

Welding of titanium and stainless steel using the composite insert

NASA Astrophysics Data System (ADS)

Cherepanov, A. N.; Mali, V. I.; Orishich, A. M.; Malikov, A. G.; Drozdov, V. O.; Malyutina, Y. N.

2016-11-01

The paper concerns the possibility of obtaining a lasting permanent joint of dissimilar metals: technically pure titanium and stainless steel using laser welding and an intermediate composite insert. The insert was a four-layer composition of plates of steel, copper, niobium, and titanium welded by explosion. The material layers used in the insert prevented the molten steel and titanium from mixing, which excluded the formation of brittle intermetallic compounds, such as FeTi and Fe2Ti. The optimization of explosion welding parameters provided a high quality of the four-layer composition and the absence of defects in the area of the joint of insert plates. The results of strength tests showed that values of the ultimate strength and yield of the permanent joint with the composite insert welded by explosion are comparable to the strength characteristics of titanium.

WITHDRAWN: Grommets (ventilation tubes) for recurrent acute otitis media in children.

PubMed

Lau, Loretta; Mick, Paul; Nunez, Desmond A

2018-04-06

This is an update of a Cochrane review first published in The Cochrane Library in Issue 4, 2008 and previously updated in 2011.Acute suppurative otitis media is one of the most common infectious diseases in childhood. Recurrent acute otitis media is defined for the purposes of this review as either three or more acute infections of the middle ear cleft in a six-month period, or at least four episodes in a year. Strategies for managing the condition include the assessment and modification of risk factors where possible, repeated courses of antibiotics for each new infection, antibiotic prophylaxis and the insertion of ventilation tubes (grommets). To establish whether grommet insertion reduces the frequency of episodes of recurrent acute otitis media and the proportion of symptomatic children. The Cochrane Ear, Nose and Throat Disorders Group (CENTDG) Trials Search Co-ordinator searched the CENTDG Trials Register; Central Register of Controlled Trials (CENTRAL 2014, Issue 10); PubMed; EMBASE; CINAHL; Web of Science; Clinicaltrials.gov; ICTRP and additional sources for published and unpublished trials. The date of the search was 6 November 2014. Randomised controlled trials comparing grommet insertion versus control (antibiotics/other treatments/no treatment) for recurrent acute otitis media in children aged from 0 to 16 years. Two authors independently selected studies. Three authors independently assessed study quality and extracted data. We synthesised data descriptively. Two randomised controlled trials with a total of 148 participants are included in this review. The overall risk of bias in the studies is unclear.The first study randomised 95 children to grommets or control (antibiotic treatment of acute otitis media episodes). For the primary outcome, this study showed that grommet insertion leads to a mean reduction of 1.5 episodes of acute otitis media in the first six months after treatment. In six months of follow-up significantly more children in the grommet group had no episodes of acute otitis media (P value < 0.001). Complications of surgery included grommet blockage with acute otitis media requiring re-operation within six months in 3/54 children who underwent grommet insertion. Adverse effects were not documented in the control group. The following pre-defined secondary outcomes were not reported: change in symptom scores for otalgia or otorrhoea, alteration in the frequency of otalgia or otorrhoea, and number of days at nursery or school lost secondary to acute otitis media.The second study reported on 53 of 68 children who were randomised to grommet insertion or six months of once a day sulfamethoxazole and trimethoprim antibiotic prophylaxis. There was no significant difference in the primary outcome, number of episodes of acute otitis media, during the six-month follow-up between grommet insertion and antibiotic treatment groups (64.5% in the surgical group versus 45.4% in the antibiotic group had no recurrence, P value = 0.4). Two participants underwent grommet re-insertion to replace extruded tubes during the follow-up period. The only other adverse effect reported was the development of a skin rash in two patients in the medical group. Other pre-defined secondary outcome measures were not reported. The study has a high risk of bias and the results should be interpreted cautiously. Grommets significantly increase the number of acute otitis media-free children in the first six months after insertion compared to children who receive no treatment. Grommet insertion maybe of equivalent efficacy to once a day antibiotic prophylaxis. Further research is required to confirm the advantage of grommets over no treatment, investigate the effect beyond six months, compare grommet effectiveness against alternative active treatments and confirm the low risk of adverse effects compared to no treatment and all active treatments in recurrent acute otitis media. In the interim clinicians should consider the possible adverse effects of grommet insertion and alternative treatments before recommending surgery.

Pressure recovery performance of conical diffusers at high subsonic Mach numbers

NASA Technical Reports Server (NTRS)

Dolan, F. X.; Runstadler, P. W., Jr.

1973-01-01

The pressure recovery performance of conical diffusers has been measured for a wide range of geometries and inlet flow conditions. The approximate level and location (in terms of diffuser geometry of optimum performance were determined. Throat Mach numbers from low subsonic (m sub t equals 0.2) through choking (m sub t equals 1.0) were investigated in combination with throat blockage from 0.03 to 0.12. For fixed Mach number, performance was measured over a fourfold range of inlet Reynolds number. Maps of pressure recovery are presented as a function of diffuser geometry for fixed sets of inlet conditions. The influence of inlet blockage, throat Mach number, and inlet Reynolds number is discussed.

Quantum detection of wormholes.

PubMed

Sabín, Carlos

2017-04-06

We show how to use quantum metrology to detect a wormhole. A coherent state of the electromagnetic field experiences a phase shift with a slight dependence on the throat radius of a possible distant wormhole. We show that this tiny correction is, in principle, detectable by homodyne measurements after long propagation lengths for a wide range of throat radii and distances to the wormhole, even if the detection takes place very far away from the throat, where the spacetime is very close to a flat geometry. We use realistic parameters from state-of-the-art long-baseline laser interferometry, both Earth-based and space-borne. The scheme is, in principle, robust to optical losses and initial mixedness.

Detection of strep throat causing bacterium directly from medical swabs by touch spray - mass spectrometry

PubMed Central

Jarmusch, Alan K.; Pirro, Valentina; Kerian, Kevin S.; Cooks, Graham

2014-01-01

Strep throat causing Streptococcus pyogenes was detected in vitro and in simulated clinical samples by performing touch spray ionization - mass spectrometry. MS analysis took only seconds to reveal characteristic bacterial and human lipids. Medical swabs were used as the substrate for ambient ionization. This work constitutes the initial step in developing a noninvasive MS-based test for clinical diagnosis of strep throat. It is limited to the single species, S. pyogenes, which is responsible for the vast majority of cases. The method is complementary to and, with further testing, a potential alternative to current methods of point-of-care detection of S. pyogenes. PMID:25102079

Tuvan throat singing and harmonics

NASA Astrophysics Data System (ADS)

Ruiz, Michael J.; Wilken, David

2018-05-01

Tuvan throat singing, also called overtone singing, provides for an exotic demonstration of the physics of harmonics as well as introducing an Asian musical aesthetic. A low fundamental is sung and the singer skillfully alters the resonances of the vocal system to enhance an overtone (harmonic above the fundamental). The result is that the listener hears two pitches simultaneously. Harmonics such as H8, H9, H10, and H12 form part of a pentatonic scale and are commonly selected for melody tones by Tuvan singers. A real-time spectrogram is provided in a video (Ruiz M J 2018 Video: Tuvan Throat Singing and Harmonics http://mjtruiz.com/ped/tuva/) so that Tuvan harmonics can be visualized as they are heard.

Biased insert for installing data transmission components in downhole drilling pipe

DOEpatents

Hall, David R [Provo, UT; Briscoe, Michael A [Lehi, UT; Garner, Kory K [Payson, UT; Wilde, Tyson J [Spanish Fork, UT

2007-04-10

An apparatus for installing data transmission hardware in downhole tools includes an insert insertable into the box end or pin end of drill tool, such as a section of drill pipe. The insert typically includes a mount portion and a slide portion. A data transmission element is mounted in the slide portion of the insert. A biasing element is installed between the mount portion and the slide portion and is configured to create a bias between the slide portion and the mount portion. This biasing element is configured to compensate for varying tolerances encountered in different types of downhole tools. In selected embodiments, the biasing element is an elastomeric material, a spring, compressed gas, or a combination thereof.

Fracture of Reduced-Diameter Zirconia Dental Implants Following Repeated Insertion.

PubMed

Karl, Matthias; Scherg, Stefan; Grobecker-Karl, Tanja

Achievement of high insertion torque values indicating good primary stability is a goal during dental implant placement. The objective of this study was to evaluate whether or not two-piece implants made from zirconia ceramic may be damaged as a result of torque application. A total of 10 two-piece zirconia implants were repeatedly inserted into polyurethane foam material with increasing density and decreasing osteotomy size. The insertion torque applied was measured, and implants were checked for fractures by applying the fluorescent penetrant method. Weibull probability of failure was calculated based on the recorded insertion torque values. Catastrophic failures could be seen in five of the implants from two different batches at insertion torques ranging from 46.0 to 70.5 Ncm, while the remaining implants (all belonging to one batch) survived. Weibull probability of failure seems to be low at the manufacturer-recommended maximum insertion torque of 35 Ncm. Chipping fractures at the thread tips as well as tool marks were the only otherwise observed irregularities. While high insertion torques may be desirable for immediate loading protocols, zirconia implants may fracture when manufacturer-recommended insertion torques are exceeded. Evaluating bone quality prior to implant insertion may be useful.

Design and Demonstration of Automated Data Analysis Algorithms for Ultrasonic Inspection of Complex Composite Panels with Bonds

DTIC Science & Technology

2016-02-01

certification process. INTRODUCTION The ultrasonic inspection of aerospace composites has been demonstrated to be one of the most effective methods to...normal part conditions. Anomalous indications studied in this program include inserted materials, porosity, ply ‘laps and gaps’, and wrinkles . Inserted...partially scanned inserts at the radii. Wrinkles , laps and gaps have also been included in the truth table, but detection rates for these flaws are

High Precision Grids for Neutron, Hard X-Ray, and Gamma-Ray Imaging Systems

NASA Technical Reports Server (NTRS)

Campbell, Jonathan W. (Inventor)

2002-01-01

Fourier telescopes permit observations over a very broad band of energy. They generally include synthetic spatial filtering structures, known as multilayer grids or grid pairs consisting of alternate layers of absorbing and transparent materials depending on whether neutrons or photons are being imaged. For hard x-rays and gamma rays high (absorbing) and low (transparent) atomic number elements, termed high-Z and low-Z materials may be used. Fabrication of these multilayer grid structures is not without its difficulties. Herein the alternate layers of the higher material and the lower material are inserted in a polyhedron, transparent to photons of interest, through an open face of the polyhedron. The inserted layers are then uniformly compressed to form a multilayer grid.

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101830, and TBD).

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830).

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. A larger image is available without labels (No. 0101755).

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Long anterior zonules and pigment dispersion.

PubMed

Moroi, Sayoko E; Lark, Kurt K; Sieving, Paul A; Nouri-Mahdavi, Kouros; Schlötzer-Schrehardt, Ursula; Katz, Gregory J; Ritch, Robert

2003-12-01

To describe pigment dispersion associated with long anterior zonules. Multicenter observational case series. Fifteen patients, seven of whom were treated for glaucoma or ocular hypertension, were identified with long anterior zonules and pigment dispersion. Transmission electron microscopy was performed on one anterior capsule specimen. All patients had anterior zonules that inserted centrally on the lens capsule. Signs of pigment dispersion included corneal endothelial pigmentation, loss of the pupillary ruff, and variable trabecular meshwork pigmentation. Ultrasound biomicroscopy verified the lack of posterior iris insertion and concavity. There was no exfoliation material. Transmission electron microscopy showed zonular lamellae with adherent pigment granules, and no exfoliation material. Long anterior zonules inserted onto the central lens capsule may cause mechanical disruption of the pigment epithelium at the pupillary ruff and central iris leading to pigment dispersion.

76 FR 62164 - VASRD Improvement Forum-Updating Disability Criteria for the Respiratory System, Cardiovascular...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... Respiratory System, Cardiovascular System, Hearing Impairment, and Ear, Nose and Throat Diseases AGENCY... System, Cardiovascular System, Hearing Impairment, and Ear, Nose and Throat Diseases. The purpose of this...) the Cardiovascular System (38 CFR 4.100-4.104), (3) the Impairment of Auditory Acuity (38 CFR 4.85 and...

Acquisition of plumage polymorphism in white-throated sparrows

Treesearch

Carter T. Atkinson; C. John Ralph

1980-01-01

The White-throated Sparrow (Zonotrichia albicollis) was thought to be polymorphic in breeding plumage, having distinct white and tan phases that are bimodal in distribution and independent of sex. Vardy (1971), however, submitted evidence that plumage type is determined primarily by age, sex, and molt cycle. We reexamined this question by measuring plumage...

The role of plumage polymorphism in dominance relationshipt of the white-throated sparrow

Treesearch

Doris J. Watt; C. John Ralph; Carter T. Atkinson

1984-01-01

We studied dominance behaviors of captive winter flocks of White-throated Sparrows (Zonotrichia albicollis) in central Pennsylvania. Preliminary tests with a small group of birds indicated that there might be differences in behaviors between color morphs if age and sexual differences were controlled. Studies of two larger groups produced...

Mach Stability Improvements Using an Existing Second Throat Capability at the National Transonic Facility

NASA Technical Reports Server (NTRS)

Chan, David T.; Balakrishna, Sundareswara; Walker, Eric L.; Goodliff, Scott L.

2015-01-01

Recent data quality improvements at the National Transonic Facility have an intended goal of reducing the Mach number variation in a data point to within plus or minus 0.0005, with the ultimate goal of reducing the data repeatability of the drag coefficient for full-span subsonic transport models at transonic speeds to within half a drag count. This paper will discuss the Mach stability improvements achieved through the use of an existing second throat capability at the NTF to create a minimum area at the end of the test section. These improvements were demonstrated using both the NASA Common Research Model and the NTF Pathfinder-I model in recent experiments. Sonic conditions at the throat were verified using sidewall static pressure data. The Mach variation levels from both experiments in the baseline tunnel configuration and the choked tunnel configuration will be presented and the correlation between Mach number and drag will also be examined. Finally, a brief discussion is given on the consequences of using the second throat in its location at the end of the test section.

Food-borne outbreak of group G streptococcal sore throat in an Israeli military base.

PubMed Central

Cohen, D.; Ferne, M.; Rouach, T.; Bergner-Rabinowitz, S.

1987-01-01

A food-borne outbreak of sore throat caused by Lancefield group G beta-haemolytic streptococci and involving 50 persons occurred in May 1983 in an Israeli military camp. All of the patients available for clinical examination had sore throat and difficulty in swallowing. Exudative tonsillitis occurred in 46% of the patients and the body temperature was above 37.5 degrees C in 81%. The pattern of attack was uniform over the base and 37 became ill during the night and morning of the 5 May. Thirty-two (84%) of the throat cultures taken from 37 patients grew group G beta-haemolytic streptococci. Eight of 29 contacts were positive for group G beta-haemolytic streptococci and 6 of the 28 foodhandlers examined had positive cultures of the same group. The organism was also isolated from one food sample. The epidemiological and laboratory investigations indicated that a food handler, a convalescent carrier of group G streptococci, might have been the source of infection. Assumptions on the potential of non-group A streptococci to cause epidemics are discussed. PMID:3678389

Emergency core cooling system

DOEpatents

Schenewerk, William E.; Glasgow, Lyle E.

1983-01-01

A liquid metal cooled fast breeder reactor provided with an emergency core cooling system includes a reactor vessel which contains a reactor core comprising an array of fuel assemblies and a plurality of blanket assemblies. The reactor core is immersed in a pool of liquid metal coolant. The reactor also includes a primary coolant system comprising a pump and conduits for circulating liquid metal coolant to the reactor core and through the fuel and blanket assemblies of the core. A converging-diverging venturi nozzle with an intermediate throat section is provided in between the assemblies and the pump. The intermediate throat section of the nozzle is provided with at least one opening which is in fluid communication with the pool of liquid sodium. In normal operation, coolant flows from the pump through the nozzle to the assemblies with very little fluid flowing through the opening in the throat. However, when the pump is not running, residual heat in the core causes fluid from the pool to flow through the opening in the throat of the nozzle and outwardly through the nozzle to the assemblies, thus providing a means of removing decay heat.

Mach Stability Improvements Using an Existing Second Throat Capability at the National Transonic Facility

NASA Technical Reports Server (NTRS)

Chan, David T.

2015-01-01

Recent data quality improvements at the National Transonic Facility (NTF) have an intended goal of reducing the Mach number variation in a data point to within unit vector A plus or minus 0.0005, with the ultimate goal of reducing the data repeatability of the drag coefficient for full-span subsonic transport models at transonic speeds to within half of a drag count. This paper will discuss the Mach stability improvements achieved through the use of an existing second throat capability at the NTF to create a minimum area at the end of the test section. These improvements were demonstrated using both the NASA Common Research Model and the NTF Pathfinder-I model in recent experiments. Sonic conditions at the throat were verified using sidewall static pressure data. The Mach variation levels from both experiments in the baseline tunnel configuration and the choked tunnel configuration will be presented. Finally, a brief discussion is given on the consequences of using the second throat in its location at the end of the test section.

Cold tolerance of the Australian spur-throated locust, Austracris guttulosa.

PubMed

Woodman, James D

2012-03-01

The cold tolerance of overwintering adult Spur-throated locusts, Austracris guttulosa, was examined using measures of supercooling point relative to gender, environmental acclimation and feeding state as well as mortality for a range of sub-zero temperature exposure treatments. Freezing was lethal and supercooling points ranged from -6 to -12.8°C, but were statistically independent of fresh mass, body water content, acclimation, and/or gut content in fed and starved individuals. A significant interaction effect of gender and feeding status showed that the larger bodied females had decreased supercooling capacity with increased food material in the digestive tract. Post-freezing dissections revealed differences in the amount of freshly consumed and retained food material in the digestive tract between fed and starved individuals of each gender, which could explain this effect based on inoculation of ice crystallisation by food particles. Above supercooling temperatures, neither gender nor the rate of cooling had a significant effect on mortality. When cooled from 25°C at 0.1 or 0.5°Cmin(-1) to a range of experimental minimum temperatures held for 3h, survival was ~74% to -7°C, but declined sharply to ~37% when cooled to -8°C or lower. Although the laboratory experiments reported here suggest that A. guttulosa is not freeze tolerant and unable to rapidly cold harden, exposure to typical cold and frosty nights that very rarely reach below -8°C as a night minimum in the field would be unlikely to cause mortality in the vast majority of overwintering aggregations. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Physical Explanation of Archie's Porosity Exponent in Granular Materials: A Process-Based, Pore-Scale Numerical Study

NASA Astrophysics Data System (ADS)

Niu, Qifei; Zhang, Chi

2018-02-01

The empirical Archie's law has been widely used in geosciences and engineering to explain the measured electrical resistivity of many geological materials, but its physical basis has not been fully understood yet. In this study, we use a pore-scale numerical approach combining discrete element-finite difference methods to study Archie's porosity exponent m of granular materials over a wide porosity range. Numerical results reveal that at dilute states (e.g., porosity ϕ > 65%), m is exclusively related to the particle shape and orientation. As the porosity decreases, the electric flow in pore space concentrates progressively near particle contacts and m increases continuously in response to the intensified nonuniformity of the local electrical field. It is also found that the increase in m is universally correlated with the volume fraction of pore throats for all the samples regardless of their particle shapes, particle size range, and porosities.

A feasibility service evaluation of screening and treatment of group A streptococcal pharyngitis in community pharmacies.

PubMed

Thornley, T; Marshall, G; Howard, P; Wilson, A P R

2016-11-01

The UK 5 year antimicrobial resistance strategy recognizes the role of point-of-care diagnostics to identify where antimicrobials are required, as well as to assess the appropriateness of the diagnosis and treatment. A sore throat test-and-treat service was introduced in 35 community pharmacies across two localities in England during 2014-15. Trained pharmacy staff assessed patients presenting with a sore throat using the Centor scoring system and patients meeting three or all four of the criteria were offered a throat swab test for Streptococcus pyogenes, Lancefield group A streptococci. Patients with a positive throat swab test were offered antibiotic treatment. Following screening by pharmacy staff, 149/367 (40.6%) patients were eligible for throat swab testing. Of these, only 36/149 (24.2%) were positive for group A streptococci. Antibiotics were supplied to 9.8% (n = 36/367) of all patients accessing the service. Just under half of patients that were not showing signs of a bacterial infection (60/123, 48.8%) would have gone to their general practitioner if the service had not been available. This study has shown that it is feasible to deliver a community-pharmacy-based screening and treatment service using point-of-care testing. This type of service has the potential to support the antimicrobial resistance agenda by reducing unnecessary antibiotic use and inappropriate antibiotic consumption. © The Author 2016. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy.

Changes in Hyolaryngeal Movement and Swallowing Function After Neuromuscular Electrical Stimulation in Patients With Dysphagia

PubMed Central

Lee, Hoo Young; Hong, Ji Seong; Lee, Kil Chan; Shin, Yoon-Kyum

2015-01-01

Objective To investigate immediate changes in hyolaryngeal movement and swallowing function after a cycle of neuromuscular electrical stimulation (NMES) on both submental and throat regions and submental placement alone in patients with dysphagia. Methods Fifteen patients with dysphagia were recruited. First, videofluoroscopic swallowing study (VFSS) was performed before NMES. All patients thereafter received a cycle of NMES by 2 methods of electrode placement: 1) both submental and throat regions and 2) submental placement alone concomitant with VFSS. The Penetration-Aspiration Score (PAS) and the NIH-Swallowing Safety Scale (NIH-SSS) were measured for swallowing function. Results During swallowing, hyolaryngeal descent significantly occurred by NMES on both submental and throat regions, and anterior displacement of hyolaryngeal complex was significant on submental placement alone. NMES on submental placement alone did not change the PAS and NIH-SSS. However, NMES on both submental and throat regions significantly reduced the NIH-SSS, although it did not change the PAS. Patients with no brainstem lesion and with dysphagia duration of <3 months showed significantly improved the NIH-SSS. Conclusion Immediate hyolaryngeal movement was paradoxically depressed after NMES on both submental and throat regions with significant reductions in the NIH-SSS but not the PAS, suggesting improvement in pharyngeal peristalsis and cricopharyngeal functions at the esophageal entry rather than decreased aspiration and penetration. The results also suggested that patients with dysphagia should be carefully screened when determining motor-level NMES. PMID:25932416

Usefulness of Leukocyte Esterase Test Versus Rapid Strep Test for Diagnosis of Acute Strep Pharyngitis

PubMed Central

2015-01-01

Objective: A study to compare the usage of throat swab testing for leukocyte esterase on a test strip(urine dip stick-multi stick) to rapid strep test for rapid diagnosis of Group A Beta hemolytic streptococci in cases of acute pharyngitis in children. Hypothesis: The testing of throat swab for leukocyte esterase on test strip currently used for urine testing may be used to detect throat infection and might be as useful as rapid strep. Methods: All patients who come with a complaint of sore throat and fever were examined clinically for erythema of pharynx, tonsils and also for any exudates. Informed consent was obtained from the parents and assent from the subjects. 3 swabs were taken from pharyngo-tonsillar region, testing for culture, rapid strep & Leukocyte Esterase. Results: Total number is 100. Cultures 9(+); for rapid strep== 84(-) and16 (+); For LE== 80(-) and 20(+) Statistics: From data configuration Rapid Strep versus LE test don’t seem to be a random (independent) assignment but extremely aligned. The Statistical results show rapid and LE show very agreeable results. Calculated Value of Chi Squared Exceeds Tabulated under 1 Degree Of Freedom (P<.0.0001) reject Null Hypothesis and Conclude Alternative Conclusions: Leukocyte esterase on throat swab is as useful as rapid strep test for rapid diagnosis of strep pharyngitis on test strip currently used for urine dip stick causing acute pharyngitis in children. PMID:27335975

Passive Rocket Diffuser Testing: Reacting Flow Performance of Four Second-Throat Geometries

NASA Technical Reports Server (NTRS)

Jones, Daniel R.; Allgood, Daniel C.; Saunders, Grady P.

2016-01-01

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure. As one of the nation's largest rocket testing facilities, the performance and design limitations of diffusers are of great interest to NASA's Stennis Space Center. This paper describes a series of tests conducted on four diffuser configurations to better understand the effects of inlet geometry and throat area on starting behavior and boundary layer separation. The diffusers were tested for a duration of five seconds with a 1455-pound thrust, LO2/GH2 thruster to ensure they each reached aerodynamic steady state. The effects of a water spray ring at the diffuser exits and a water-cooled deflector plate were also evaluated. Static pressure and temperature measurements were taken at multiple axial locations along the diffusers, and Computational Fluid Dynamics (CFD) simulations were used as a tool to aid in the interpretation of data. The hot combustion products were confirmed to enable the diffuser start condition with tighter second throats than predicted by historical cold-flow data or the theoretical normal shock method. Both aerodynamic performance and heat transfer were found to increase with smaller diffuser throats. Spray ring and deflector cooling water had negligible impacts on diffuser boundary layer separation. CFD was found to accurately capture diffuser shock structures and full-flowing diffuser wall pressures, and the qualitative behavior of heat transfer. However, the ability to predict boundary layer separated flows was not consistent.

Conspicuous female ornamentation and tests of male mate preference in threespine sticklebacks (Gasterosteus aculeatus).

PubMed

Wright, Daniel Shane; Pierotti, Michele E R; Rundle, Howard D; McKinnon, Jeffrey S

2015-01-01

Sexual selection drives the evolution of exaggerated male ornaments in many animal species. Female ornamentation is now acknowledged also to be common but is generally less well understood. One example is the recently documented red female throat coloration in some threespine stickleback (Gasterosteus aculeatus) populations. Although female sticklebacks often exhibit a preference for red male throat coloration, the possibility of sexual selection on female coloration has been little studied. Using sequential and simultaneous mate choice trials, we examined male mate preferences for female throat color, as well as pelvic spine color and standard length, using wild-captured threespine sticklebacks from the Little Campbell River, British Columbia. In a multivariate analysis, we found no evidence for a population-level mate preference in males, suggesting the absence of directional sexual selection on these traits arising from male mate choice. Significant variation was detected among males in their preference functions, but this appeared to arise from differences in their mean responsiveness across mating trials and not from variation in the strength (i.e., slope) of their preference, suggesting the absence of individual-level preferences as well. When presented with conspecific intruder males, male response decreased as intruder red throat coloration increased, suggesting that males can discriminate color and other aspects of phenotype in our experiment and that males may use these traits in intrasexual interactions. The results presented here are the first to explicitly address male preference for female throat color in threespine sticklebacks.

Conspicuous Female Ornamentation and Tests of Male Mate Preference in Threespine Sticklebacks (Gasterosteus aculeatus)

PubMed Central

Wright, Daniel Shane; Pierotti, Michele E. R.; Rundle, Howard D.; McKinnon, Jeffrey S.

2015-01-01

Sexual selection drives the evolution of exaggerated male ornaments in many animal species. Female ornamentation is now acknowledged also to be common but is generally less well understood. One example is the recently documented red female throat coloration in some threespine stickleback (Gasterosteus aculeatus) populations. Although female sticklebacks often exhibit a preference for red male throat coloration, the possibility of sexual selection on female coloration has been little studied. Using sequential and simultaneous mate choice trials, we examined male mate preferences for female throat color, as well as pelvic spine color and standard length, using wild-captured threespine sticklebacks from the Little Campbell River, British Columbia. In a multivariate analysis, we found no evidence for a population-level mate preference in males, suggesting the absence of directional sexual selection on these traits arising from male mate choice. Significant variation was detected among males in their preference functions, but this appeared to arise from differences in their mean responsiveness across mating trials and not from variation in the strength (i.e., slope) of their preference, suggesting the absence of individual-level preferences as well. When presented with conspecific intruder males, male response decreased as intruder red throat coloration increased, suggesting that males can discriminate color and other aspects of phenotype in our experiment and that males may use these traits in intrasexual interactions. The results presented here are the first to explicitly address male preference for female throat color in threespine sticklebacks. PMID:25806520

Sexual Dimorphism in Melanin Pigmentation, Feather Coloration and Its Heritability in the Barn Swallow (Hirundo rustica)

PubMed Central

Saino, Nicola; Romano, Maria; Rubolini, Diego; Teplitsky, Celine; Ambrosini, Roberto; Caprioli, Manuela; Canova, Luca; Wakamatsu, Kazumasa

2013-01-01

Melanin is the main pigment in animal coloration and considerable variation in the concentrations of the two melanin forms (pheo- and eumlanin) in pigmented tissues exists among populations and individuals. Melanin-based coloration is receiving increasing attention particularly in socio-sexual communication contexts because the melanocortin system has been hypothesized to provide a mechanistic basis for covariation between coloration and fitness traits. However, with few notable exceptions, little detailed information is available on inter-individual and inter-population variation in melanin pigmentation and on its environmental, genetic and ontogenetic components. Here, we investigate melanin-based coloration in an Italian population of a passerine bird, the barn swallow (Hirundo rustica rustica), its sex- and age-related variation, and heritability. The concentrations of eu- and pheomelanin in the throat (brown) and belly (white-to-brownish) feathers differed between sexes but not according to age. The relative concentration of either melanin (Pheo:Eu) differed between sexes in throat but not in belly feathers, and the concentrations in males compared to females were larger in belly than in throat feathers. There were weak correlations between the concentrations of melanins within as well as among plumage regions. Coloration of belly feathers was predicted by the concentration of both melanins whereas coloration of throat feathers was only predicted by pheomelanin in females. In addition, Pheo:Eu predicted coloration of throat feathers in females and that of belly feathers in males. Finally, we found high heritability of color of throat feathers. Melanization was found to differ from that recorded in Hirundo rustica rustica from Scotland or from H. r. erythrogaster from North America. Hence, present results show that pigmentation strategies vary in a complex manner according to sex and plumage region, and also among geographical populations, potentially reflecting adaptation to different natural and sexual selection regimes, and that some coloration components seem to be highly heritable. PMID:23469134

TOPPITS: Trial Of Proton Pump Inhibitors in Throat Symptoms. Study protocol for a randomised controlled trial.

PubMed

Watson, Gillian; O'Hara, James; Carding, Paul; Lecouturier, Jan; Stocken, Deborah; Fouweather, Tony; Wilson, Janet

2016-04-01

Persistent throat symptoms and Extra Oesophageal Reflux (EOR) are among the commonest reasons for attendance at a secondary care throat or voice clinic. There is a growing trend to treat throat symptom patients with proton pump inhibitors (PPIs) to suppress stomach acid, but most controlled studies fail to demonstrate a significant benefit of PPI over placebo. In addition, patient views on PPI use vary widely. A UK multi-centre, randomised, controlled trial for adults with persistent throat symptoms to compare the effectiveness of treatment with the proton pump inhibitor (PPI) lansoprazole versus placebo. The trial includes a six-month internal pilot, during which three sites will recruit 30 participants in total, to assess the practicality of the trial and assess the study procedures and willingness of the patient population to participate. If the pilot is successful, three additional sites will be opened to recruitment, and a further 302 participants recruited across the six main trial sites. Further trial sites may be opened, as necessary. The main trial will continue for a further 18 months. Participants will be followed up for 12 months from randomisation, throughout which both primary and secondary outcome data will be collected. The primary outcome is change in Reflux Symptom Index (RSI) score, the 'area standard' for this type of assessment, after 16 weeks (four months) of treatment. Secondary outcomes are RSI changes at 12 months after randomisation, Quality of Life assessment at four and 12 months, laryngeal mucosal changes, assessments of compliance and side effects, and patient-reported satisfaction. TOPPITS is designed to evaluate the relative effectiveness of treatment with a proton pump inhibitor versus placebo in patients with persistent throat symptoms. This will provide valuable information to clinicians and GPs regarding the treatment and management of care for these patients, on changes in symptoms, and in Quality of Life, over time. ISRCTN38578686 . Registered 17 April 2014.

Evaluation of Simplexa Group A Strep Direct Kit Compared to Hologic Group A Streptococcal Direct Assay for Detection of Group A Streptococcus in Throat Swabs.

PubMed

Church, Deirdre L; Lloyd, Tracie; Larios, Oscar; Gregson, Daniel B

2018-03-01

Diagnosis of bacterial pharyngitis is confirmed by detection of group A Streptococcus (GAS) in patient throat samples. Testing of throat samples has historically relied on culture, but new molecular methods allow much faster test turnaround time (i.e., same day versus 48 to 72 h for culture). Our laboratory uses the Hologic GAS Direct (GASD) assay for screening more than 125,000 throat samples per year. Simplexa GAS Direct is a new real-time quantitative PCR (qPCR) assay that does not require initial DNA extraction. Performance of Simplexa qPCR was compared to GASD. A total of 289 throat swabs were collected from patients attending ambulatory clinics in Calgary, Alberta, Canada. A total of 60 (20.8%) of the samples were initially GAS positive by either method: 54 by both methods, 4 by Simplex qPCR alone, and 2 by GASD alone. An in-house PCR using a unique GAS primer set was used to resolve the 6 discrepant results. Overall, GASD compared to Simplexa qPCR had a sensitivity, specificity, positive predictive value, and negative predictive value of 93.1% versus 100%, 100% versus 100%, 100% versus 100%, and 98.31% versus 100%, respectively. Implementation of Simplexa qPCR in our laboratory setting would cost more but allow the high sample volume to be reported in half the time and save 0.62 medical laboratory technician (MLT) full-time equivalent (FTE). In comparison to culture, the implementation of Simplexa qPCR would save 2.79 medical laboratory assistant (MLA) FTE plus 0.94 MLT FTE. Simplexa qPCR has improved performance and diagnostic efficiency in a high-volume laboratory compared to GASD for GAS detection in throat swabs. Copyright © 2018 American Society for Microbiology.

The prevalence of acute respiratory symptoms and role of protective measures among Malaysian hajj pilgrims.

PubMed

Deris, Zakuan Zainy; Hasan, Habsah; Sulaiman, Siti Amrah; Wahab, Mohd Suhaimi Ab; Naing, Nyi Nyi; Othman, Nor Hayati

2010-01-01

Respiratory symptoms including cough, runny nose, sore throat, and fever are the most common clinical manifestations faced by hajj pilgrims in Mecca. The aim of the study was to determine the prevalence of respiratory symptoms among Malaysian hajj pilgrims and the effect of a few protective measures taken by hajj pilgrims to reduce respiratory symptoms. A cross-sectional study was conducted by distributing survey forms to Malaysian hajj pilgrims at transit center before flying back to Malaysia. The recruitment of respondents to the survey was on a voluntary basis. A total of 387 survey forms were available for analysis. The mean age was 50.4 +/- 11.0 years. The common respiratory symptoms among Malaysian hajj pilgrims were: cough 91.5%, runny nose 79.3%, fever 59.2%, and sore throat 57.1%. The prevalence of hajj pilgrims with triad of cough, subjective fever, and sore throat were 40.1%. The symptoms lasted less than 2 weeks in the majority of cases. Only 3.6% did not suffer from any of these symptoms. Seventy-two percent of hajj pilgrims received influenza vaccination before departure and 72.9% wore facemasks. Influenza vaccination was not associated with any of respiratory symptoms but it was significantly associated with longer duration of sore throat. Wearing masks was significantly associated with sore throat and longer duration of sore throat and fever. The prevalence of respiratory symptoms was high among Malaysian hajj pilgrims and the current protective measures seemed inadequate to reduce it. Beside standardization of the term used in hajj studies, more collaborative effort should be taken to reduce respiratory symptoms. The hajj authority should prepare for the challenge of pandemic influenza by providing more healthcare facilities and implementation of more strict measures to reduce the transmission of pandemic influenza strain among hajj pilgrims.

Health Instruction Packages: Specific Nursing Skills.

ERIC Educational Resources Information Center

Bates, Clarice; And Others

Text, illustrations, and exercises are utilized in a set of five learning modules designed to instruct nursing students in a variety of clinical skills. The first module, "Down the Tube: Insertion of a Nasogastric Tube" by Clarice Bates, describes materials and procedures used to insert a nasogastric tube through the nose and esophagus…

Disposable and removable nucleic acid extraction and purification cartridges for automated flow-through systems

DOEpatents

Regan, John Frederick

2014-09-09

Removable cartridges are used on automated flow-through systems for the purpose of extracting and purifying genetic material from complex matrices. Different types of cartridges are paired with specific automated protocols to concentrate, extract, and purifying pathogenic or human genetic material. Their flow-through nature allows large quantities sample to be processed. Matrices may be filtered using size exclusion and/or affinity filters to concentrate the pathogen of interest. Lysed material is ultimately passed through a filter to remove the insoluble material before the soluble genetic material is delivered past a silica-like membrane that binds the genetic material, where it is washed, dried, and eluted. Cartridges are inserted into the housing areas of flow-through automated instruments, which are equipped with sensors to ensure proper placement and usage of the cartridges. Properly inserted cartridges create fluid- and air-tight seals with the flow lines of an automated instrument.

Long lifetime hollow cathodes for 30-cm mercury ion thrusters

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Kerslake, W. R.

1976-01-01

An experimental investigation of hollow cathodes for 30-cm Hg bombardment thrusters was carried out. Both main and neutralizer cathode configurations were tested with both rolled foil inserts coated with low work function material and impregnated porous tungsten inserts. Temperature measurements of an impregnated insert at various positions in the cathode were made. These, along with the cathode thermal profile are presented. A theory for rolled foil and impregnated insert operation and lifetime in hollow cathodes is developed. Several endurance tests, as long as 18,000 hours at emission currents of up to 12 amps were attained with no degradation in performance.

Methods of Using a Magnetic Field Response Sensor Within Closed, Electrically Conductive Containers

NASA Technical Reports Server (NTRS)

Woodward, Stanley E.; Taylor, Bryant D.

2010-01-01

Magnetic field response sensors are a class of sensors that are powered via oscillating magnetic fields, and when electrically active, respond with their own magnetic fields with attributes dependent upon the magnitude of the physical quantity being measured. A magnetic field response recorder powers and interrogates the magnetic sensors [see Magnetic-Field-Response Measurement- Acquisition System, NASA Tech Briefs Vol. 30, No, 6 (June 2006, page 28)]. Electrically conductive containers have low transmissivity for radio frequency (RF) energy and thus present problems for magnetic field response sensors. It is necessary in some applications to have a magnetic field response sensor s capacitor placed in these containers. Proximity to conductive surfaces alters the inductance and capacitance of the sensors. As the sensor gets closer to a conductive surface, the electric field and magnetic field energy of the sensor is reduced due to eddy currents being induced in the conductive surface. Therefore, the capacitors and inductors cannot be affixed to a conductive surface or embedded in a conductive material. It is necessary to have a fixed separation away from the conductive material. The minimum distance for separation is determined by the desired sensor response signal to noise ratio. Although the inductance is less than what it would be if it were not in proximity to the conductive surface, the inductance is fixed. As long as the inductance is fixed, all variations of the magnetic field response are due to capacitance changes. Numerous variations of inductor mounting can be utilized, such as providing a housing that provides separation from the conductive material as well as protection from impact damage. The sensor can be on the same flexible substrate with a narrow throat portion of the sensor between the inductor and the capacitor, Figure 1. The throat is of sufficient length to allow the capacitor to be appropriately placed within the container and the inductor placed outside the container. The throat is fed through the orifice in the container wall (e.g., fuel tank opening) and connects to the inductor and capacitor via electrical leads to form a closed circuit, Figure 2. Another embodiment is to have the inductor and capacitor fabricated as separate units. In this embodiment, the inductor is mounted external to the container, and the capacitor is mounted internal to the container, Figure 1. Electrical leads are fed through the orifice to connect the inductor and capacitor, Figure 2. When a container holding multiple sensors is made of a conductive material, an antenna can be placed internal to the container. An internal antenna allows all components of the sensors to reside inside the container. The antenna must be separated from the container wall s conductive surface. Additionally, the inductors must be maintained in a fixed position relative to and separated from the container

DEVELOPMENT OF DIES FOR EXTRUSION OF COMPLEX SHAPES OF STEEL AND REFRACTORY ALLOYS. Interim Technical Documentary Progress Report to Aeronautical Systems Division for the Period September 16,1962 through December 31, 1962

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, J.G.; Jenkins, R.G.; White, A.M.

1963-03-01

A number of ceramics, metallic compounds, and ceramic-metal composites were successfully hot pressed into the shape of die inserts. Steels were extruded through several of these for the purpose of evaluating the materials or to study methods of supporting the die inserts. Refractory metal inserts were also used in similar tests. Hot pressed inserts consisting of 80 vo1% Al/sub 2/O/ sub 3/--10 vol% W and 80 vol% ThO/sub 2/--10 vol% W cracked but did not erode. Sintered molybdenum inserts flowed excessively, whereas sintered tungsten inserts flowed to a lesser degree. A hard die casing with a slight shrink fit appearsmore » to be the most satisfactory method of support. (auth)« less

Damping insert materials for settling chambers of supersonic wind tunnels

NASA Astrophysics Data System (ADS)

Wu, Jie; Radespiel, Rolf

2017-03-01

This study describes the application of a novel damping insert material for reducing the flow fluctuations in a tandem nozzle supersonic wind tunnel. This new damping material is composed of multi-layer stainless steel wired meshes. The influences of the multi-layer mesh, such as the quantity of the mesh layer and the installed location in the settling chamber, to the freestream quality have been investigated. A Pitot probe instrumented with a Kulite pressure sensor and a hot-wire probe are employed to monitor the flow fluctuation in the test section of the wind tunnel. Thereafter, a combined modal analysis is applied for the disturbance qualification. Additionally, the transient Mach number in the test section is measured. The disturbance qualification indicates that the multi-layer mesh performs well in providing reduction of vorticity reduction and acoustic fluctuations. Comparable flow quality of the freestream was also obtained using a combination of flexible damping materials. However, the life-span of the new damping materials is much longer. The time transient of the Mach number measured in the test section indicates that the mean flow is rather constant over run time. Furthermore, the time-averaged pressure along the settling chamber is recorded and it shows the distribution of pressure drop by settling chamber inserts.

27 CFR 4.61 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., circular, mailer, book insert, catalog, promotional material, sales pamphlet, or any written, printed... or other reading material (i.e., news release) in any periodical or publication or newspaper for the...

Ear, nose and throat problems in Accident and Emergency.

PubMed

Reynolds, Tanya

Nurses working in A&E departments throughout the UK frequently encounter patients with ear, nose and throat conditions. While the majority of these are straightforward, a small number are serious and even life-threatening. Tanya Reynolds discusses the nursing management of this group of patients and stresses the importance of appropriate assessment, pain management and referral.

Know and Share the Facts about Flu Vaccination

ERIC Educational Resources Information Center

Grohskopf, Lisa

2012-01-01

Flu is a contagious respiratory illness caused by influenza viruses that infect the nose, throat, and lungs. It can cause mild to severe illness, and sometimes can lead to death. Symptoms of flu can include fever or a feverish feeling, cough, sore throat, runny or stuffy nose, muscle or body aches, headache, fatigue, vomiting, and diarrhea. Flu…

Global ENT Outreach: Taking Ear, Nose, and Throat Treatment and Surgery Techniques to Ethiopia

ERIC Educational Resources Information Center

Wagner, Richard

2007-01-01

The author, as an otolaryngologist and the Director of Global ENT (Ear, Nose and Throat) Outreach, traveled to Ethiopia to help 11 children who could not breathe because of respiratory papillomas blocking their airways and who had been hospitalized for years. The disease, called juvenile respiratory papillomatosis, is what affected these 11…

Vacuum polarization of a quantized scalar field in the thermal state in a long throat

NASA Astrophysics Data System (ADS)

Popov, Arkady A.

2016-12-01

Vacuum polarization of scalar fields in the background of a long throat is investigated. The field is assumed to be both massive or massless, with arbitrary coupling to the scalar curvature, and in a thermal state at an arbitrary temperature. Analytical approximation for ⟨φ2⟩ren is obtained.

Using Evaluability Assessment to Improve Program Evaluation for the Blue-Throated Macaw Environmental Education Project in Bolivia

ERIC Educational Resources Information Center

Salvatierra da Silva, Daniela; Jacobson, Susan K.; Monroe, Martha C.; Israel, Glenn D.

2016-01-01

An evaluability assessment of a program to save a critically endangered bird helped prepare the Blue-throated Macaw Environmental Education Project for evaluation and program improvement. The evaluability assessment facilitated agreement among key stakeholders on evaluation criteria and intended uses of evaluation information in order to maximize…

Coinfection with Hepatozoon sp. and Canine Distemper Virus in a Yellow-throated Marten ( Martes flavigula koreana) in Korea.

PubMed

Park, Surim; Choi, Ul Soo; Kim, Eun Ju; Lee, Jong Hyun; Lee, Hae Beom; Cho, Ho Seong; Kim, Wonil; Lim, Chae Woong; Kim, Bumseok

2016-04-28

We describe coinfection with Hepatozoon sp. and canine distemper virus (CDV) in a yellow-throated marten ( Martes flavigula koreana). We found Hepatozoon cysts in muscular tissue and viral inclusion bodies in the brain. Hepatozoon sp., and CDV was confirmed in blood and brain, respectively, by PCR.

Significance of Hemolytic Colonies in Throat Cultures

PubMed Central

Quinn, Robert W.; Lowry, P. Nye

1969-01-01

These studies indicate that a single strain of hemolytic streptococci almost exclusively predominates the bacterial flora in patients with streptococcal infections and in the carrier state. One can proceed with confidence that, in isolating streptococci from throat swabs cultured on blood-agar plates, only a single hemolytic colony need be picked for serological grouping and typing. PMID:4888863

Do Shale Pore Throats Have a Threshold Diameter for Oil Storage?

PubMed Central

Zou, Caineng; Jin, Xu; Zhu, Rukai; Gong, Guangming; Sun, Liang; Dai, Jinxing; Meng, Depeng; Wang, Xiaoqi; Li, Jianming; Wu, Songtao; Liu, Xiaodan; Wu, Juntao; Jiang, Lei

2015-01-01

In this work, a nanoporous template with a controllable channel diameter was used to simulate the oil storage ability of shale pore throats. On the basis of the wetting behaviours at the nanoscale solid-liquid interfaces, the seepage of oil in nano-channels of different diameters was examined to accurately and systematically determine the effect of the pore diameter on the oil storage capacity. The results indicated that the lower threshold for oil storage was a pore throat of 20 nm, under certain conditions. This proposed pore size threshold provides novel, evidence-based criteria for estimating the geological reserves, recoverable reserves and economically recoverable reserves of shale oil. This new understanding of shale oil processes could revolutionize the related industries. PMID:26314637

Do Shale Pore Throats Have a Threshold Diameter for Oil Storage?

PubMed

Zou, Caineng; Jin, Xu; Zhu, Rukai; Gong, Guangming; Sun, Liang; Dai, Jinxing; Meng, Depeng; Wang, Xiaoqi; Li, Jianming; Wu, Songtao; Liu, Xiaodan; Wu, Juntao; Jiang, Lei

2015-08-28

In this work, a nanoporous template with a controllable channel diameter was used to simulate the oil storage ability of shale pore throats. On the basis of the wetting behaviours at the nanoscale solid-liquid interfaces, the seepage of oil in nano-channels of different diameters was examined to accurately and systematically determine the effect of the pore diameter on the oil storage capacity. The results indicated that the lower threshold for oil storage was a pore throat of 20 nm, under certain conditions. This proposed pore size threshold provides novel, evidence-based criteria for estimating the geological reserves, recoverable reserves and economically recoverable reserves of shale oil. This new understanding of shale oil processes could revolutionize the related industries.

Static Investigation of a Multiaxis Thrust-Vectoring Nozzle With Variable Internal Contouring Ability

NASA Technical Reports Server (NTRS)

Wing, David J.; Mills, Charles T. L.; Mason, Mary L.

1997-01-01

The thrust efficiency and vectoring performance of a convergent-divergent nozzle were investigated at static conditions in the model preparation area of the Langley 16-Foot Transonic Tunnel. The diamond-shaped nozzle was capable of varying the internal contour of each quadrant individually by using cam mechanisms and retractable drawers to produce pitch and yaw thrust vectoring. Pitch thrust vectoring was achieved by either retracting the lower drawers to incline the throat or varying the internal flow-path contours to incline the throat. Yaw thrust vectoring was achieved by reducing flow area left of the nozzle centerline and increasing flow area right of the nozzle centerline; a skewed throat deflected the flow in the lateral direction.

MO-FG-204-06: A New Algorithm for Gold Nano-Particle Concentration Identification in Dual Energy CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, L; Shen, C; Ng, M

Purpose: Gold nano-particle (GNP) has recently attracted a lot of attentions due to its potential as an imaging contrast agent and radiotherapy sensitiser. Imaging the GNP at its low contraction is a challenging problem. We propose a new algorithm to improve the identification of GNP based on dual energy CT (DECT). Methods: We consider three base materials: water, bone, and gold. Determining three density images from two images in DECT is an under-determined problem. We propose to solve this problem by exploring image domain sparsity via an optimization approach. The objective function contains four terms. A data-fidelity term ensures themore » fidelity between the identified material densities and the DECT images, while the other three terms enforces the sparsity in the gradient domain of the three images corresponding to the density of the base materials by using total variation (TV) regularization. A primal-dual algorithm is applied to solve the proposed optimization problem. We have performed simulation studies to test this model. Results: Our digital phantom in the tests contains water, bone regions and gold inserts of different sizes and densities. The gold inserts contain mixed material consisting of water with 1g/cm3 and gold at a certain density. At a low gold density of 0.0008 g/cm3, the insert is hardly visible in DECT images, especially for those with small sizes. Our algorithm is able to decompose the DECT into three density images. Those gold inserts at a low density can be clearly visualized in the density image. Conclusion: We have developed a new algorithm to decompose DECT images into three different material density images, in particular, to retrieve density of gold. Numerical studies showed promising results.« less

Insertable fluid flow passage bridgepiece and method

DOEpatents

Jones, Daniel O.

2000-01-01

A fluid flow passage bridgepiece for insertion into an open-face fluid flow channel of a fluid flow plate is provided. The bridgepiece provides a sealed passage from a columnar fluid flow manifold to the flow channel, thereby preventing undesirable leakage into and out of the columnar fluid flow manifold. When deployed in the various fluid flow plates that are used in a Proton Exchange Membrane (PEM) fuel cell, bridgepieces of this invention prevent mixing of reactant gases, leakage of coolant or humidification water, and occlusion of the fluid flow channel by gasket material. The invention also provides a fluid flow plate assembly including an insertable bridgepiece, a fluid flow plate adapted for use with an insertable bridgepiece, and a method of manufacturing a fluid flow plate with an insertable fluid flow passage bridgepiece.

First Materials Science Research Facility Rack Capabilities and Design Features

NASA Technical Reports Server (NTRS)

Cobb, S.; Higgins, D.; Kitchens, L.; Curreri, Peter (Technical Monitor)

2002-01-01

The first Materials Science Research Rack (MSRR-1) is the primary facility for U.S. sponsored materials science research on the International Space Station. MSRR-1 is contained in an International Standard Payload Rack (ISPR) equipped with the Active Rack Isolation System (ARIS) for the best possible microgravity environment. MSRR-1 will accommodate dual Experiment Modules and provide simultaneous on-orbit processing operations capability. The first Experiment Module for the MSRR-1, the Materials Science Laboratory (MSL), is an international cooperative activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center (ESTEC). The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts which provide distinct thermal processing capabilities. Module Inserts currently planned for the MSL are a Quench Module Insert, Low Gradient Furnace, and a Solidification with Quench Furnace. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Development (SPD) Group. Transparent furnace assemblies include capabilities for vapor transport processes and annealing of glass fiber preforms. This Experiment Module is replaceable on-orbit. This paper will describe facility capabilities, schedule to flight and research opportunities.

27 CFR 5.62 - Definition.

Code of Federal Regulations, 2011 CFR

2011-04-01

... booklet, menu, wine card, leaflet, circular, mailer, book insert, catalog, promotional material, sales....42 of this part. (b) Any editorial or other reading material (i.e., news release) in any periodical...

Methods to Predict Stresses in Cutting Inserts Brazed Using Iron-Carbon Brazing Alloy

NASA Astrophysics Data System (ADS)

Konovodov, V. V.; Valentov, A. V.; Retuynskiy, O. Yu; Esekuev, Sh B.

2016-04-01

This work describes a method for predicting residual and operating stresses in a flat-form tool insert made of tungsten free carbides brazed using iron-carbon alloy. According to the studies’ results it is concluded that the recommendations relating to the limitation of a melting point of tool brazing alloys (950-1100°C according to different data) are connected with a negative impact on tools as a composite made of dissimilar materials rather than on hard alloys as a tool material. Due to the cooling process stresses inevitably occur in the brazed joint of dissimilar materials, and these stresses increase with the higher solidification temperature of the brazing alloy.

Magnetic latch trigger for inherent shutdown assembly

DOEpatents

Sowa, Edmund S.

1976-01-01

An inherent shutdown assembly for a nuclear reactor is provided. A neutron absorber is held ready to be inserted into the reactor core by a magnetic latch. The latch includes a magnet whose lines of force are linked by a yoke of material whose Curie point is at the critical temperature of the reactor at which the neutron absorber is to be inserted into the reactor core. The yoke is in contact with the core coolant or fissionable material so that when the coolant or the fissionable material increase in temperature above the Curie point the yoke loses its magnetic susceptibility and the magnetic link is broken, thereby causing the absorber to be released into the reactor core.

High-energy metal air batteries

DOEpatents

Zhang, Ji-Guang; Xiao, Jie; Xu, Wu; Wang, Deyu; Williford, Ralph E.; Liu, Jun

2014-07-01

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

High-energy metal air batteries

DOEpatents

Zhang, Ji-Guang; Xiao, Jie; Xu, Wu; Wang, Deyu; Williford, Ralph E.; Liu, Jun

2013-07-09

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

Cell wall elongation mode in Gram-negative bacteria is determined by peptidoglycan architecture.

PubMed

Turner, Robert D; Hurd, Alexander F; Cadby, Ashley; Hobbs, Jamie K; Foster, Simon J

2013-01-01

Cellular integrity and morphology of most bacteria is maintained by cell wall peptidoglycan, the target of antibiotics essential in modern healthcare. It consists of glycan strands, cross-linked by peptides, whose arrangement determines cell shape, prevents lysis due to turgor pressure and yet remains dynamic to allow insertion of new material, and hence growth. The cellular architecture and insertion pattern of peptidoglycan have remained elusive. Here we determine the peptidoglycan architecture and dynamics during growth in rod-shaped Gram-negative bacteria. Peptidoglycan is made up of circumferentially oriented bands of material interspersed with a more porous network. Super-resolution fluorescence microscopy reveals an unexpected discontinuous, patchy synthesis pattern. We present a consolidated model of growth via architecture-regulated insertion, where we propose only the more porous regions of the peptidoglycan network that are permissive for synthesis.

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Here the transparent furnace is extracted for servicing. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).