75 FR 35816 - Establishment of the Consumer Operated and Oriented Plan (CO-OP) Advisory Board

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-23

... (CO-OP) Advisory Board AGENCY: Department of Health and Human Services, Office of Consumer Information & Insurance Oversight. ACTION: Federal Register Notice. Authority: The Consumer Operated and Oriented Plan (CO... (PPACA) that calls for the establishment of the Consumer Operated and Oriented Plans (CO-OP) Program...

A Prospective Comparison of Robotic and Laparoscopic Pyeloplasty

PubMed Central

Link, Richard E.; Bhayani, Sam B.; Kavoussi, Louis R.

2006-01-01

Objective: To determine whether robotic-assisted pyeloplasty (RLP) has any significant clinical or cost advantages over laparoscopic pyeloplasty (LP) for surgeons already facile with intracorporeal suturing. Summary Background Data: LP has become an established management approach for primary ureteropelvic junction obstruction. More recently, the da Vinci robot has been applied to this procedure (RLP) in an attempt to shorten the learning curve. Whether RLP provides any significant advantage over LP for the experienced laparoscopist remains unclear. Methods: Ten consecutive cases each of transperitoneal RLP and LP performed by a single surgeon were compared prospectively with respect to surgical times and perioperative outcomes. Cost assessment was performed by sensitivity analysis using a mathematical cost model incorporating operative time, anesthesia fees, consumables, and capital equipment depreciation. Results: The RLP and LP groups had statistically indistinguishable demographics, pathology, and similar perioperative outcomes. Mean operative and total room time for RLP was significantly longer than LP by 19.5 and 39.0 minutes, respectively. RLP was much more costly than LP (2.7 times), due to longer operative time, increased consumables costs, and depreciation of the costly da Vinci system. However, even if depreciation was eliminated, RLP was still 1.7 times as costly as LP. One-way sensitivity analysis showed that LP operative time must increase to almost 6.5 hours for it to become cost equivalent to RLP. Conclusions: For the experienced laparoscopist, application of the da Vinci robot resulted in no significant clinical advantage and added substantial cost to transperitoneal laparoscopic dismembered pyeloplasty. PMID:16552199

A prospective comparison of robotic and laparoscopic pyeloplasty.

PubMed

Link, Richard E; Bhayani, Sam B; Kavoussi, Louis R

2006-04-01

To determine whether robotic-assisted pyeloplasty (RLP) has any significant clinical or cost advantages over laparoscopic pyeloplasty (LP) for surgeons already facile with intracorporeal suturing. LP has become an established management approach for primary ureteropelvic junction obstruction. More recently, the da Vinci robot has been applied to this procedure (RLP) in an attempt to shorten the learning curve. Whether RLP provides any significant advantage over LP for the experienced laparoscopist remains unclear. Ten consecutive cases each of transperitoneal RLP and LP performed by a single surgeon were compared prospectively with respect to surgical times and perioperative outcomes. Cost assessment was performed by sensitivity analysis using a mathematical cost model incorporating operative time, anesthesia fees, consumables, and capital equipment depreciation. The RLP and LP groups had statistically indistinguishable demographics, pathology, and similar perioperative outcomes. Mean operative and total room time for RLP was significantly longer than LP by 19.5 and 39.0 minutes, respectively. RLP was much more costly than LP (2.7 times), due to longer operative time, increased consumables costs, and depreciation of the costly da Vinci system. However, even if depreciation was eliminated, RLP was still 1.7 times as costly as LP. One-way sensitivity analysis showed that LP operative time must increase to almost 6.5 hours for it to become cost equivalent to RLP. For the experienced laparoscopist, application of the da Vinci robot resulted in no significant clinical advantage and added substantial cost to transperitoneal laparoscopic dismembered pyeloplasty.

Analysis on burnup step effect for evaluating reactor criticality and fuel breeding ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saputra, Geby; Purnama, Aditya Rizki; Permana, Sidik

Criticality condition of the reactors is one of the important factors for evaluating reactor operation and nuclear fuel breeding ratio is another factor to show nuclear fuel sustainability. This study analyzes the effect of burnup steps and cycle operation step for evaluating the criticality condition of the reactor as well as the performance of nuclear fuel breeding or breeding ratio (BR). Burnup step is performed based on a day step analysis which is varied from 10 days up to 800 days and for cycle operation from 1 cycle up to 8 cycles reactor operations. In addition, calculation efficiency based onmore » the variation of computer processors to run the analysis in term of time (time efficiency in the calculation) have been also investigated. Optimization method for reactor design analysis which is used a large fast breeder reactor type as a reference case was performed by adopting an established reactor design code of JOINT-FR. The results show a criticality condition becomes higher for smaller burnup step (day) and for breeding ratio becomes less for smaller burnup step (day). Some nuclides contribute to make better criticality when smaller burnup step due to individul nuclide half-live. Calculation time for different burnup step shows a correlation with the time consuming requirement for more details step calculation, although the consuming time is not directly equivalent with the how many time the burnup time step is divided.« less

Testing single point incremental forming molds for thermoforming operations

NASA Astrophysics Data System (ADS)

Afonso, Daniel; de Sousa, Ricardo Alves; Torcato, Ricardo

2016-10-01

Low pressure polymer processing processes as thermoforming or rotational molding use much simpler molds then high pressure processes like injection. However, despite the low forces involved with the process, molds manufacturing for this operations is still a very material, energy and time consuming operation. The goal of the research is to develop and validate a method for manufacturing plastically formed sheets metal molds by single point incremental forming (SPIF) operation for thermoforming operation. Stewart platform based SPIF machines allow the forming of thick metal sheets, granting the required structural stiffness for the mold surface, and keeping the short lead time manufacture and low thermal inertia.

Traffic management simulation development.

DOT National Transportation Integrated Search

2011-01-03

Microscopic simulation can provide significant support to traffic management center (TMC) operations. However, traffic simulation applications require data that are expensive and time-consuming to collect. Data collected by TMCs can be used as a prim...

Cassini Attitude Control Operations - Guidelines Levied on Science to Extend Reaction Wheel Life

NASA Technical Reports Server (NTRS)

Mittelsteadt, Carson O.

2011-01-01

The Cassini spacecraft was launched on October 15, 1997 and arrived at Saturn on June 30, 2004. It has performed detailed observations and remote sensing of Saturn, its rings, and its satellites since that time. Cassini deployed the European-built Huygens probe, which descended through the Titan atmosphere (Saturn's largest moon) and landed on its surface on January 14, 2005. The Cassini mission has recently been approved by NASA to continue through September of 2017. This 7-year extension is called the Solstice mission and it presents challenges to the spacecraft operations team and its ability to maintain the health of the spacecraft. To keep the spacecraft healthy for 7 more years, the spacecraft team must carefully manage hydrazine use (about 48% of the 132 kg launch load remains as of January 2011). A vital part of conserving hydrazine is to use the reaction wheel assembly (RWA) control system for precise pointing and slews wherever possible. In any given week, the Cassini spacecraft is commanded to use RWA control about 99% of the time, with about 1% of the time requiring reaction control system (RCS) thruster control (to perform Delta V course corrections or to bias the RWA momentum). Such extensive use of the RWA hardware throughout the mission requires that the RWAs be operated in a way that minimizes degradation in the RWA electronics, DC motor, and spin bearing for each reaction wheel. Three consumables in particular have been identified for the RWAs: (1) Total number of revolutions for each RWA. (2) Time spent at very low wheel speeds. At these low speeds, good elasto-hydrodynamic (EHD) film lubrication may be compromised. (3) Total number of on/off power cycles. The second of these consumables, minimizing the time spent at very low wheel speeds, is especially important to keep the spin bearing healthy and well-lubricated. These consumables are actively managed by the attitude control operations team throughout the mission. One vital management technique is to predict individual RWA momentum (given the pointing and slews that are needed to collect the best science) and to bias the RWA momentum in a way that reduces both the total number of revolutions as well as the time spent below EHD wheel speed. Another strategy to protect RWA health is to alter the planned pointing of the spacecraft (which can affect science collection) so that the RWA consumables are conserved. This paper focuses on why this second technique is needed, and discusses how guidelines have been developed by the attitude control team which affects the planned science pointing, so that science data can be most optimally collected while still minimizing RWA consumable usage.

Email Marketing for U.S. Army and Special Operations Forces (SOF) Recruiting

DTIC Science & Technology

2007-12-01

church. Users had the ability to read the church’s ministry goals and standpoint on religion . The site also contained podcasts of recent church...Cost vs. Time Table for Phone and Email The formula used in this model is: Y =CX The Decision Variables are listed below: X1= Phone Leads X2... Millennial Consumers. Consumer Behavior. United States. Molenaar, C. (2002). The Future of Marketing. Great Britain: Pearson Education

A Battalion/Division Fiscal Control System for Training Resource Management.

DTIC Science & Technology

1981-12-01

of each command using it. With many Army fiscal procedures consuming large volumes of time and resources to support operations with questionable...Document (FAD)) spe- cifying the appropriation and budget programs for which the funds may be used . The FAD is the installation’s approved financial...operating budgets. Although a proper term would be operating targets, budget is used for ease of understanding. These funds are principally for general

Commercialization of microfluidic devices.

PubMed

Volpatti, Lisa R; Yetisen, Ali K

2014-07-01

Microfluidic devices offer automation and high-throughput screening, and operate at low volumes of consumables. Although microfluidics has the potential to reduce turnaround times and costs for analytical devices, particularly in medical, veterinary, and environmental sciences, this enabling technology has had limited diffusion into consumer products. This article analyzes the microfluidics market, identifies issues, and highlights successful commercialization strategies. Addressing niche markets and establishing compatibility with existing workflows will accelerate market penetration. Copyright © 2014 Elsevier Ltd. All rights reserved.

Advanced Simulation in Undergraduate Pilot Training: Visual Display Development

DTIC Science & Technology

1975-12-01

properties of each member were calculated manually and were inserted by means of punched cards, thus it was relatively easy (but time consuming ) to...investigations leading to the decision to employ an all-glass approach which consisted of a two-part glass funnel produced by Corning Glass Wo ks... consuming . After complete sets of materials were selected they had to be cemented into a final assembly. This had to be done in two operations because of the

Testing the accuracy of timing reports in visual timing tasks with a consumer-grade digital camera.

PubMed

Smyth, Rachael E; Oram Cardy, Janis; Purcell, David

2017-06-01

This study tested the accuracy of a visual timing task using a readily available and relatively inexpensive consumer grade digital camera. A visual inspection time task was recorded using short high-speed video clips and the timing as reported by the task's program was compared to the timing as recorded in the video clips. Discrepancies in these two timing reports were investigated further and based on display refresh rate, a decision was made whether the discrepancy was large enough to affect the results as reported by the task. In this particular study, the errors in timing were not large enough to impact the results of the study. The procedure presented in this article offers an alternative method for performing a timing test, which uses readily available hardware and can be used to test the timing in any software program on any operating system and display.

Intelligent and robust optimization frameworks for smart grids

NASA Astrophysics Data System (ADS)

Dhansri, Naren Reddy

A smart grid implies a cyberspace real-time distributed power control system to optimally deliver electricity based on varying consumer characteristics. Although smart grids solve many of the contemporary problems, they give rise to new control and optimization problems with the growing role of renewable energy sources such as wind or solar energy. Under highly dynamic nature of distributed power generation and the varying consumer demand and cost requirements, the total power output of the grid should be controlled such that the load demand is met by giving a higher priority to renewable energy sources. Hence, the power generated from renewable energy sources should be optimized while minimizing the generation from non renewable energy sources. This research develops a demand-based automatic generation control and optimization framework for real-time smart grid operations by integrating conventional and renewable energy sources under varying consumer demand and cost requirements. Focusing on the renewable energy sources, the intelligent and robust control frameworks optimize the power generation by tracking the consumer demand in a closed-loop control framework, yielding superior economic and ecological benefits and circumvent nonlinear model complexities and handles uncertainties for superior real-time operations. The proposed intelligent system framework optimizes the smart grid power generation for maximum economical and ecological benefits under an uncertain renewable wind energy source. The numerical results demonstrate that the proposed framework is a viable approach to integrate various energy sources for real-time smart grid implementations. The robust optimization framework results demonstrate the effectiveness of the robust controllers under bounded power plant model uncertainties and exogenous wind input excitation while maximizing economical and ecological performance objectives. Therefore, the proposed framework offers a new worst-case deterministic optimization algorithm for smart grid automatic generation control.

Comparison of a Frail-Friendly Nomogram with Physician-Adjusted Warfarin Dosage for Prophylaxis after Orthopaedic Surgery on a Geriatric Rehabilitation Unit

ERIC Educational Resources Information Center

Freter, Susan; Bowles, Susan K.

2005-01-01

Warfarin dosing for thromboprophylaxis in post-operative patients is time-consuming. Warfarin-dosing nomograms can be used in post-operative arthroplasty patients, but warfarin requirements are lower in frail older people. We modified an existing post-arthroplasty nomogram to a frail-friendly version and evaluated its performance in a frail…

Save Energy Dollars with DOE Operations and Maintenance Guide

ERIC Educational Resources Information Center

Appel, Margo

2010-01-01

At budget-crunching time, school administrators and business officials sometimes find themselves trimming the district's budget for teachers, textbooks, and technology in order to cover ballooning energy costs. Nearly one-third of the energy consumed in the average U.S. school is wasted. The country's least efficient schools use four times more…

Improving delivery routes using combined heuristic and optimization in a consumer goods distribution company

NASA Astrophysics Data System (ADS)

Wibisono, E.; Santoso, A.; Sunaryo, M. A.

2017-11-01

XYZ is a distributor of various consumer goods products. The company plans its delivery routes daily and in order to obtain route construction in a short amount of time, it simplifies the process by assigning drivers based on geographic regions. This approach results in inefficient use of vehicles leading to imbalance workloads. In this paper, we propose a combined method involving heuristic and optimization to obtain better solutions in acceptable computation time. The heuristic is based on a time-oriented, nearest neighbor (TONN) to form clusters if the number of locations is higher than a certain value. The optimization part uses a mathematical modeling formulation based on vehicle routing problem that considers heterogeneous vehicles, time windows, and fixed costs (HVRPTWF) and is used to solve routing problem in clusters. A case study using data from one month of the company’s operations is analyzed, and data from one day of operations are detailed in this paper. The analysis shows that the proposed method results in 24% cost savings on that month, but it can be as high as 54% in a day.

Measurement of SIFT operating system overhead

NASA Technical Reports Server (NTRS)

Palumbo, D. L.; Butler, R. W.

1985-01-01

The overhead of the software implemented fault tolerance (SIFT) operating system was measured. Several versions of the operating system evolved. Each version represents different strategies employed to improve the measured performance. Three of these versions are analyzed. The internal data structures of the operating systems are discussed. The overhead of the SIFT operating system was found to be of two types: vote overhead and executive task overhead. Both types of overhead were found to be significant in all versions of the system. Improvements substantially reduced this overhead; even with these improvements, the operating system consumed well over 50% of the available processing time.

An FPGA computing demo core for space charge simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Jinyuan; Huang, Yifei; /Fermilab

2009-01-01

In accelerator physics, space charge simulation requires large amount of computing power. In a particle system, each calculation requires time/resource consuming operations such as multiplications, divisions, and square roots. Because of the flexibility of field programmable gate arrays (FPGAs), we implemented this task with efficient use of the available computing resources and completely eliminated non-calculating operations that are indispensable in regular micro-processors (e.g. instruction fetch, instruction decoding, etc.). We designed and tested a 16-bit demo core for computing Coulomb's force in an Altera Cyclone II FPGA device. To save resources, the inverse square-root cube operation in our design is computedmore » using a memory look-up table addressed with nine to ten most significant non-zero bits. At 200 MHz internal clock, our demo core reaches a throughput of 200 M pairs/s/core, faster than a typical 2 GHz micro-processor by about a factor of 10. Temperature and power consumption of FPGAs were also lower than those of micro-processors. Fast and convenient, FPGAs can serve as alternatives to time-consuming micro-processors for space charge simulation.« less

76 FR 17653 - Public Meeting of the Consumer Operated and Oriented Plan (CO-OP) Advisory Board, April 15, 2011

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-30

...] Public Meeting of the Consumer Operated and Oriented Plan (CO-OP) Advisory Board, April 15, 2011 AGENCY... of the Department of Health and Human Services' through CCIIO strategy to foster the creation of... Oversight (CCIIO) on the Department's strategy to foster the creation of qualified consumer-operated...

Defense Mapping Agency (DMA) Raster-to-Vector Analysis

DTIC Science & Technology

1984-11-30

model) to pinpoint critical deficiencies and understand trade-offs between alternative solutions. This may be exemplified by the allocation of human ...process, prone to errors (i.e., human operator eye/motor control limitations), and its time consuming nature (as a function of data density). It should...achieved through the facilities of coinputer interactive graphics. Each error or anomaly is individually identified by a human operator and corrected

Method and apparatus for controlling electrode gap during vacuum consumable arc remelting

DOEpatents

Fisher, R.W.; Maroone, J.P.; Tipping, D.W.; Zanner, F.J.

During vacuum consumable arc remelting the electrode gap between a consumable electrode and a pool of molten metal is difficult to control. The present invention monitors drop shorts by detecting a decrease in the voltage between the consumable electrode and molten pool. The drop shorts and their associated voltage reductions occur as repetitive pulses which are closely correlated to the electrode gap. Thus, the method and apparatus of the present invention controls electrode gap based upon drop shorts detected from the monitored anode-cathode voltage. The number of drop shorts are accumulated, and each time the number of drop shorts reach a predetermined number, the average period between drop shorts is calculated from this predetermined number and the time in which this number is accumulated. This average drop short period is used in a drop short period electrode gap model which determines the actual electrode gap from the drop short. The actual electrode gap is then compared with a desired electrode gap which is selected to produce optimum operating conditions and the velocity of the consumable error is varied based upon the gap error. The consumable electrode is driven according to any prior art system at this velocity. In the preferred embodiment, a microprocessor system is utilized to perform the necessary calculations and further to monitor the duration of each drop short. If any drop short exceeds a preset duration period, the consumable electrode is rapidly retracted a predetermined distance to prevent bonding of the consumable electrode to the molten remelt.

Apollo Soyuz Test Project Weights and Mass Properties Operational Management System

NASA Technical Reports Server (NTRS)

Collins, M. A., Jr.; Hischke, E. R.

1975-01-01

The Apollo Soyuz Test Project (ASTP) Weights and Mass Properties Operational Management System was established to assure a timely and authoritative method of acquiring, controlling, generating, and disseminating an official set of vehicle weights and mass properties data. This paper provides an overview of the system and its interaction with the various aspects of vehicle and component design, mission planning, hardware and software simulations and verification, and real-time mission support activities. The effect of vehicle configuration, design maturity, and consumables updates is discussed in the context of weight control.

Operation of controls on consumer products by physically impaired users.

PubMed

Kanis, H

1993-06-01

The self-reliance of the physically impaired can be seriously jeopardized by their inability to operate everyday products, especially if both upper extremities are impaired. To determine the difficulties impaired users encounter in operating consumer product controls, on-site video recordings were made of subjects suffering from arthritis or a muscular disease. Subjects' force exertion was compared with that of a group of nonimpaired users. The resulting inventory allowed the analysis of the manipulation problems faced by impaired subjects and the development of design recommendations. In this study the force exerted by the subjects and that required to operate the controls were measured. A comparison of the results of these force measurements led to a number of conclusions. This study led to the following design recommendations: the amount of force required to operate controls should be kept as low as possible; the user should not be required to make two manipulations at the same time, such as simultaneously pushing and rotating a control device; pushing is preferable to rotating; and there should be a great degree of freedom to manipulate controls.

Oceanic Flights and Airspace: Improving Efficiency by Trajectory-Based Operations

NASA Technical Reports Server (NTRS)

Fernandes, Alicia Borgman; Rebollo, Juan; Koch, Michael

2016-01-01

Oceanic operations suffer from multiple inefficiencies, including pre-departure planning that does not adequately consider uncertainty in the proposed trajectory, restrictions on the routes that a flight operator can choose for an oceanic crossing, time-consuming processes and procedures for amending en route trajectories, and difficulties exchanging data between Flight Information Regions (FIRs). These inefficiencies cause aircraft to fly suboptimal trajectories, burning fuel and time that could be conserved. A concept to support integration of existing and emerging capabilities and concepts is needed to transition to an airspace system that employs Trajectory Based Operations (TBO) to improve efficiency and safety in oceanic operations. This paper describes such a concept and the results of preliminary activities to evaluate the concept, including a stakeholder feedback activity, user needs analysis, and high level benefits analysis.

Time-driven activity-based costing to identify opportunities for cost reduction in pediatric appendectomy.

PubMed

Yu, Yangyang R; Abbas, Paulette I; Smith, Carolyn M; Carberry, Kathleen E; Ren, Hui; Patel, Binita; Nuchtern, Jed G; Lopez, Monica E

2016-12-01

As reimbursement programs shift to value-based payment models emphasizing quality and efficient healthcare delivery, there exists a need to better understand process management to unearth true costs of patient care. We sought to identify cost-reduction opportunities in simple appendicitis management by applying a time-driven activity-based costing (TDABC) methodology to this high-volume surgical condition. Process maps were created using medical record time stamps. Labor capacity cost rates were calculated using national median physician salaries, weighted nurse-patient ratios, and hospital cost data. Consumable costs for supplies, pharmacy, laboratory, and food were derived from the hospital general ledger. Time-driven activity-based costing resulted in precise per-minute calculation of personnel costs. Highest costs were in the operating room ($747.07), hospital floor ($388.20), and emergency department ($296.21). Major contributors to length of stay were emergency department evaluation (270min), operating room availability (395min), and post-operative monitoring (1128min). The TDABC model led to $1712.16 in personnel costs and $1041.23 in consumable costs for a total appendicitis cost of $2753.39. Inefficiencies in healthcare delivery can be identified through TDABC. Triage-based standing delegation orders, advanced practice providers, and same day discharge protocols are proposed cost-reducing interventions to optimize value-based care for simple appendicitis. II. Copyright © 2016 Elsevier Inc. All rights reserved.

An Incentive-based Online Optimization Framework for Distribution Grids

DOE PAGES

Zhou, Xinyang; Dall'Anese, Emiliano; Chen, Lijun; ...

2017-10-09

This article formulates a time-varying social-welfare maximization problem for distribution grids with distributed energy resources (DERs) and develops online distributed algorithms to identify (and track) its solutions. In the considered setting, network operator and DER-owners pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. The proposed algorithm affords an online implementation to enable tracking of the solutions in the presence of time-varying operational conditions and changing optimization objectives. It involves a strategy where the network operator collects voltage measurements throughout the feeder to build incentive signals for the DER-owners in real time; DERs thenmore » adjust the generated/consumed powers in order to avoid the violation of the voltage constraints while maximizing given objectives. Stability of the proposed schemes is analytically established and numerically corroborated.« less

An Incentive-based Online Optimization Framework for Distribution Grids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Xinyang; Dall'Anese, Emiliano; Chen, Lijun

This article formulates a time-varying social-welfare maximization problem for distribution grids with distributed energy resources (DERs) and develops online distributed algorithms to identify (and track) its solutions. In the considered setting, network operator and DER-owners pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. The proposed algorithm affords an online implementation to enable tracking of the solutions in the presence of time-varying operational conditions and changing optimization objectives. It involves a strategy where the network operator collects voltage measurements throughout the feeder to build incentive signals for the DER-owners in real time; DERs thenmore » adjust the generated/consumed powers in order to avoid the violation of the voltage constraints while maximizing given objectives. Stability of the proposed schemes is analytically established and numerically corroborated.« less

Maintenance and operations tasks accomplished at DSS 12 during the antenna panel replacement downtime

NASA Technical Reports Server (NTRS)

Butcher, L.; Jonas, T.; Wood, W.

1982-01-01

The heavy schedule of tracking activities at the Echo Deep Space Station (DSS 12) prevents some time-consuming maintenance tasks from being performed. Careful coordination prior to and during a mandatory task (antenna panel replacement) made it possible to do a large number of unrelated tasks that ordinarily would have to be deferred. The maintenance and operations tasks accomplished during the downtime are described.

Agent Based Modeling and Simulation Framework for Supply Chain Risk Management

DTIC Science & Technology

2012-03-01

Christopher and Peck 2004) macroeconomic , policy, competition, and resource (Ghoshal 1987) value chain, operational, event, and recurring (Shi 2004...clustering algorithms in agent logic to protect company privacy ( da Silva et al. 2006), aggregation of domain context in agent data analysis logic (Xiang...Operational Availability ( OA ) for FMC and PMC. 75 Mission Capable (MICAP) Hours is the measure of total time (in a month) consumable or reparable

A Conceptual Framework for Tactical Private Satellite Networks

DTIC Science & Technology

2008-09-01

will be deployed on a controlled basis so as not to consume valuable bandwidth during critical time windows. Faults inside the network can be tracked ... attitude control , timing, and navigation - More precise station keeping - Optical LANs and inter-satellite links - Inter satellite links - New...Cluster operations, such as electromagnetic formation flying systems and remote attitude determination systems. • Distributed spacecraft computing

75 FR 36138 - Self-Regulatory Organizations; New York Stock Exchange LLC; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-24

... p.m. The 10 minute interval is a legacy time frame related to the Exchange's prior publication of... in the face of a dilemma that is unique to a physical Trading Floor, i.e., how to position resources... efficient operation of the Exchange's market by reducing the frequency of time-consuming Floor broker oral...

LOCATING LEAKS WITH ACOUSTIC TECHNOLOGY

EPA Science Inventory

Many water distribution systems in this country are almost 100 years old. About 26 percent of piping in these systems is made of unlined cast iron or steel and is in poor condition. Many methods that locate leaks in these pipes are time-consuming, costly, disruptive to operations...

Vehicle energy conservation indicating device and process for use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crump, J.M.

A vehicle energy conservation indicating device comprises an integrated instrument cluster functioning basically as a nomographic computing mechanism. The odometer distance traveled indicator computing mechanism is linked with the fuel indicating gauge mechanism such that a three variable equation computing mechanism is obtained. The three variables are distance traveled, quantity of fuel consumed and distance traveled per unit of fuel consumed. Energy conservation is achieved by operating the vehicle under such performance conditions as to produce the highest possible value for distance traveled per unit of fuel consumed. The instrument panel cluster brings the operator's attention to focus upon andmore » continuously stimulated to conserving energy. Furthermore, the vehicle energy conservation indicating device can be adapted for recording these performance variables on tape type print out. The speedometer advises the vehicle operator when he is obeying or breaking the speed laws which are enforced and monitored by the police with specific punishment prescribed for violations of the law. At this time there is no comparable procedure for enforcing vehicle energy conservation. Thus, this direct read out of distance traveled per unit of energy will moderate the operation in an analogous manner similar to subliminal advertising. This device becomes the focal point of the instrument panel along with the speedometer, thereby providing constant motivation to obey both the speed and energy conservation laws.« less

Drop short control of electrode gap

DOEpatents

Fisher, Robert W.; Maroone, James P.; Tipping, Donald W.; Zanner, Frank J.

1986-01-01

During vacuum consumable arc remelting the electrode gap between a consumable electrode and a pool of molten metal is difficult to control. The present invention monitors drop shorts by detecting a decrease in the voltage between the consumable electrode and molten pool. The drop shorts and their associated voltage reductions occur as repetitive pulses which are closely correlated to the electrode gap. Thus, the method and apparatus of the present invention controls electrode gap based upon drop shorts detected from the monitored anode-cathode voltage. The number of drop shorts are accumulated, and each time the number of drop shorts reach a predetermined number, the average period between drop shorts is calculated from this predetermined number and the time in which this number is accumulated. This average drop short period is used in a drop short period electrode gap model which determines the actual electrode gap from the drop short. The actual electrode gap is then compared with a desired electrode gap which is selected to produce optimum operating conditions and the velocity of the consumable error is varied based upon the gap error. The consumable electrode is driven according to any prior art system at this velocity. In the preferred embodiment, a microprocessor system is utilized to perform the necessary calculations and further to monitor the duration of each drop short. If any drop short exceeds a preset duration period, the consumable electrode is rapidly retracted a predetermined distance to prevent bonding of the consumable electrode to the molten remelt.

Evaluation of pollution levels due to the use of consumer fertilizers under Florida conditions.

DOT National Transportation Integrated Search

2010-08-01

The Florida Department of Transportation has taken steps to reduce the amount of phosphorus and the time release of fertilizer compounds in all of its operations. Consequently, there may be a reduction in the mass of phosphorus being released to adja...

Food Cravings Consume Limited Cognitive Resources

ERIC Educational Resources Information Center

Kemps, Eva; Tiggemann, Marika; Grigg, Megan

2008-01-01

Using Tiffany's (1990) cognitive model of drug use and craving as a theoretical basis, the present experiments investigated whether cravings for food expend limited cognitive resources. Cognitive performance was assessed by simple reaction time (Experiment 1) and an established measure of working memory capacity, the operation span task…

Emotional balances in experimental consumer choices.

PubMed

Mengov, George; Egbert, Henrik; Pulov, Stefan; Georgiev, Kalin

2008-11-01

This paper presents an experiment, which builds a bridge over the gap between neuroscience and the analysis of economic behaviour. We apply the mathematical theory of Pavlovian conditioning, known as Recurrent Associative Gated Dipole (READ), to analyse consumer choices in a computer-based experiment. Supplier reputations, consumer satisfaction, and customer reactions are operationally defined and, together with prices, related to READ's neural dynamics. We recorded our participants' decisions with their timing, and then mapped those decisions on a sequence of events generated by the READ model. To achieve this, all constants in the differential equations were determined using simulated annealing with data from 129 people. READ predicted correctly 96% of all consumer choices in a calibration sample (n=1290), and 87% in a test sample (n=903), thus outperforming logit models. The rank correlations between self-assessed and dipole-generated consumer satisfactions were 89% in the calibration sample and 78% in the test sample, surpassing by a wide margin the best linear regression model.

MARO - Mass Atrocity Response Operations: A Military Planning Handbook

DTIC Science & Technology

2010-05-01

while conveying an implied deterrent message to perpetrators. • Current military presence in the region can be reinforced with addi- tional US ...complete HUMINT network is likely to be a time- consuming process, ear- ly efforts may provide useful dividends. • Shows of force can be conducted...climate change, the impact of the information environment on military operations, and the evolving nature of warfare. coL (ret) scott Feil ( Us army) is an

A Historical Perspective of Special Operations Forces as an Instrument of Strategy.

DTIC Science & Technology

1991-01-01

government of Winston Churchill had ascended to power. For the special operations effort, fits and starts toward a more capable organization had occurred...therefore reasonable to conclude that this halting method of agent and organization development though time- consuming , eventually provided a cadre of...Command and General Staff College, Ft. Leavenworth, KS. July 21, 1999. THIS PAGE IS UNCLASSIFIED AD-B 158 452 A HISTORICAL PERSPECTIVE OF ’ SPECIAL

75 FR 81612 - The Consumer Operated and Oriented Plan (CO-OP) Advisory Board; Office of Consumer Information...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... Operated and Oriented Plan (CO-OP) Advisory Board; Office of Consumer Information and Insurance Oversight... and Insurance Oversight (OCIIO) on the Department's strategy to foster the creation of qualified... and Insurance Oversight (OCIIO) on the Department's strategy to foster the creation of qualified...

Management accounting for advanced technological environments.

PubMed

Kaplan, R S

1989-08-25

Management accounting systems designed decades ago no longer provide timely, relevant information for companies in today's highly competitive environment. New operational control and performance measurement systems are recognizing the importance of direct measurement of quality, manufacturing lead times, flexibility, and customer responsiveness, as well as more accurate measures of the actual costs of consumed resources. Activity-based cost systems can assign the costs of indirect and support resources to the specific products and activities that benefit from these resources. Both operational control and activity-based systems represent new opportunities for improved managerial information in complex, technologically advanced environments.

US Hybrid Bucket Truck APM Phase I Final Scientific Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goodarzi, Abas

Presently, there are approximately 166,000 medium- and heavy-duty (MD/HD) bucket trucks operating in the United States, the majority of which are diesel powered. These vehicles spend a significant amount of time idling at the work site to power the truck’s hydraulic boom, lights, auxiliary equipment, and cabin heating and cooling. Nationally, bucket trucks use 0.5 billion gallons of diesel fuel annually, representing 1.5 percent of the U.S.’s total diesel fuel consumption [ ]. Increasing fuel costs and environmental concerns are driving efforts to develop cleaner, quieter, more productive, and more energy efficient bucket trucks. The emissions of the bucket truckmore » have a direct effect on public health. Bucket trucks operation mode imposes heavy loads on the powertrain and results in very poor fuel efficiency and high emissions. Electric powertrains perform well in such conditions, and in recent years, a number of initiatives have been launched to explore the potential of fuel cell electric systems for bucket truck propulsion. The proposed fuel cell powered ePTO offers the best ROI and compatibility with the existing vehicles and operation and also minimized the infrastructure need. To address these problems, US Hybrid Corporation has teamed with Hawaii Center for Advanced Transportation Technologies (HCATT) and Hawaii Natural Energy Institute (HNEI) and Hawaiian Electric Company (HECO) to perform a Phase I analysis on the development and deployment of a fuel cell powered bucket truck (FCBT) for operation by HECO within the City and County of Honolulu. Based on preliminary modeling of a typical bucket truck operation, it is anticipated that the fuel cell powertrain will provide a 200% fuel economy improvement with zero emissions job-site operation and lower operating noise. The zero-emission ePTO bucket truck will also support the Greenhouse Gas (GHG) emission goals set forth by the federal government as well as the State of Hawaii. The operators within the bucket industry will also benefit from the proposed fuel cell bucket truck with zero emission job-site operation and lower operating noise. The maximum benefits of a hybrid powertrain are realized when the system is designed for the specific duty cycle of the vehicle. In the case of the bucket truck, the duty cycle consists of approximately six hours (75% of time) field operation and two hours (25% of time) in cruising mode drive to and back from job sites. The vast majority of fuel is consumed in the field operation mode, in which the vehicle is much less efficient due to the high energy expenditure while inefficiently operating the hydraulic bucket handling equipment. The amount of fuel consumed to generate hydraulic power represents approximately 50% of the total fuel consumed in field operation mode. Our cost analysis indicated that the cost premium for commercial volume production has a payback time of four years based on a hydrogen cost of $6/kg, while providing lower noise, less maintenance cost with electrically driven variable speed pump and portable packaging.« less

Link monitor and control operator assistant: A prototype demonstrating semiautomated monitor and control

NASA Technical Reports Server (NTRS)

Lee, L. F.; Cooper, L. P.

1993-01-01

This article describes the approach, results, and lessons learned from an applied research project demonstrating how artificial intelligence (AI) technology can be used to improve Deep Space Network operations. Configuring antenna and associated equipment necessary to support a communications link is a time-consuming process. The time spent configuring the equipment is essentially overhead and results in reduced time for actual mission support operations. The NASA Office of Space Communications (Code O) and the NASA Office of Advanced Concepts and Technology (Code C) jointly funded an applied research project to investigate technologies which can be used to reduce configuration time. This resulted in the development and application of AI-based automated operations technology in a prototype system, the Link Monitor and Control Operator Assistant (LMC OA). The LMC OA was tested over the course of three months in a parallel experimental mode on very long baseline interferometry (VLBI) operations at the Goldstone Deep Space Communications Center. The tests demonstrated a 44 percent reduction in pre-calibration time for a VLBI pass on the 70-m antenna. Currently, this technology is being developed further under Research and Technology Operating Plan (RTOP)-72 to demonstrate the applicability of the technology to operations in the entire Deep Space Network.

Adiabatic Demagnetisation Refrigerators for Future Sub-Millimetre Space Missions

NASA Astrophysics Data System (ADS)

Hepburn, I. D.; Davenport, I.; Smith, A.

1995-10-01

Space worthy refrigeration capable of providing a 100 mK and below heat load sink for bolometric detectors will be required for the next generation of sub-millimetre space missions. Adiabatic demagnetisation refrigeration (ADR), being a gravity independent laboratory method for obtaining such temperatures, is a favourable technique for utilisation in space. We show that by considering a 3 salt pill refrigerator rather than the classic single salt pill design the space prohibitive laboratory ADR properties of high magnetic field (6 Tesla) and a<2 K environment (provided by a bath of liquid4He) can be alleviated, while maintaining a sufficient low temperature hold time and short recycle time. The additional salt pills, composed of Gadolinium Gallium Garnet (GGG) provide intermediate cooling stages, enabling operation from a 4 K environment provided by a single 4 K mechanical cooler, thereby providing consumable free operation. Such ADRs could operate with fields as low as 1 Tesla allowing the use of high temperature, mechanically cooled superconducting magnets and so effectively remove the risk of quenching. We discuss the possibility of increasing the hold time from 3 hours, for the model presented, to between 40 and 80 hours, plus reducing the number of salt pills to two, through the use of a more efficient Garnet. We believe the technical advances necessitated by the envisaged ADRs are minimal and conclude that such ADRs offer a long orbital life time, consumable free, high efficiency means of milli-Kelvin cooling, requiring relatively little laboratory development.

Compounds of parasitic roundworm absorbing in the visible region: target molecules for detection of roundworm in Atlantic cod.

PubMed

Stormo, Svein K; Ernstsen, Arild; Nilsen, Heidi; Heia, Karsten; Sivertsen, Agnar H; Elvevoll, Edel

2004-07-01

The objective of this study was to contribute to the development of technology that will be able to replace manual operations in processing of fish fillets. Removal of parasites, black lining, remnants of skin, and bloodstains are costly and time-consuming operations to the fish processing industry. The presence of parasites in fish products tends to spoil consumers' appetites. Recent reports questioning the safety of eating cod infected with parasites might lower consumer acceptance of seafood. Presently, parasites are detected and removed manually. An average efficiency of about 75% under commercial conditions has been reported. In this study, we focused on biochemical differences between cod muscle and the prevalent anisakine nematode species (Anisakis simplex and Pseudoterranova decipiens) infecting Atlantic cod (Gadus morhua). Using reversed phase high-performance liquid chromatography equipped with a photodiode array detector, substances absorbing in the range 300 to 600 nm were identified in extracts from parasite material. These substances were not detected in extracts from cod tissue. Significant biochemical differences between cod muscle and parasite material have thus been demonstrated.

Implications of Motivating Operations for the Functional Analysis of Consumer Choice

ERIC Educational Resources Information Center

Fagerstrom, Asle; Foxall, Gordon R.; Arntzen, Erik

2010-01-01

The present article introduces the concept of Motivating Operation (MO) to the context of consumer choice and discusses the function of the concept of MO in the context of the Behavioral Perspective Model (BPM). Including MO as part of the consumer behavior setting leads to a more comprehensive analysis and, as a result, improves our understanding…

Advancing satellite operations with intelligent graphical monitoring systems

NASA Technical Reports Server (NTRS)

Hughes, Peter M.; Shirah, Gregory W.; Luczak, Edward C.

1993-01-01

For nearly twenty-five years, spacecraft missions have been operated in essentially the same manner: human operators monitor displays filled with alphanumeric text watching for limit violations or other indicators that signal a problem. The task is performed predominately by humans. Only in recent years have graphical user interfaces and expert systems been accepted within the control center environment to help reduce operator workloads. Unfortunately, the development of these systems is often time consuming and costly. At the NASA Goddard Space Flight Center (GSFC), a new domain specific expert system development tool called the Generic Spacecraft Analyst Assistant (GenSAA) has been developed. Through the use of a highly graphical user interface and point-and-click operation, GenSAA facilitates the rapid, 'programming-free' construction of intelligent graphical monitoring systems to serve as real-time, fault-isolation assistants for spacecraft analysts. Although specifically developed to support real-time satellite monitoring, GenSAA can support the development of intelligent graphical monitoring systems in a variety of space and commercial applications.

47 CFR 64.703 - Consumer information.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (Federal Communications Commission, Consumer Information Bureau, Consumer Complaints—Telephone, Washington, D.C. 20554), to which the consumer may direct complaints regarding operator services. An existing... 47 Telecommunication 3 2011-10-01 2011-10-01 false Consumer information. 64.703 Section 64.703...

47 CFR 64.703 - Consumer information.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (Federal Communications Commission, Consumer Information Bureau, Consumer Complaints—Telephone, Washington, D.C. 20554), to which the consumer may direct complaints regarding operator services. An existing... 47 Telecommunication 3 2014-10-01 2014-10-01 false Consumer information. 64.703 Section 64.703...

47 CFR 64.703 - Consumer information.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (Federal Communications Commission, Consumer Information Bureau, Consumer Complaints—Telephone, Washington, D.C. 20554), to which the consumer may direct complaints regarding operator services. An existing... 47 Telecommunication 3 2012-10-01 2012-10-01 false Consumer information. 64.703 Section 64.703...

47 CFR 64.703 - Consumer information.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (Federal Communications Commission, Consumer Information Bureau, Consumer Complaints—Telephone, Washington, D.C. 20554), to which the consumer may direct complaints regarding operator services. An existing... 47 Telecommunication 3 2013-10-01 2013-10-01 false Consumer information. 64.703 Section 64.703...

ImageJ: Image processing and analysis in Java

NASA Astrophysics Data System (ADS)

Rasband, W. S.

2012-06-01

ImageJ is a public domain Java image processing program inspired by NIH Image. It can display, edit, analyze, process, save and print 8-bit, 16-bit and 32-bit images. It can read many image formats including TIFF, GIF, JPEG, BMP, DICOM, FITS and "raw". It supports "stacks", a series of images that share a single window. It is multithreaded, so time-consuming operations such as image file reading can be performed in parallel with other operations.

Red vertical cavity surface emitting lasers (VCSELs) for consumer applications

NASA Astrophysics Data System (ADS)

Duggan, Geoffrey; Barrow, David A.; Calvert, Tim; Maute, Markus; Hung, Vincent; McGarvey, Brian; Lambkin, John D.; Wipiejewski, Torsten

2008-02-01

There are many potential applications of visible, red (650nm - 690nm) vertical cavity surface emitting lasers (VCSELs) including high speed (Gb) communications using plastic optical fiber (POF), laser mouse sensors, metrology, position sensing. Uncertainty regarding the reliability of red VCSELs has long been perceived as the most significant roadblock to their commercialization. In this paper we will present data on red VCSELs optimized for performance and reliability that will allow exploitation of this class of VCSEL in a wide range of high volume consumer, communication and medical applications. VCSELs operating at ~665nm have been fabricated on 4" GaAs substrates using MOCVD as the growth process and using standard VCSEL processing technology. The active region is AlGaInP-based and the DBR mirrors are made from AlGaAs. Threshold currents are typically less than 2mA, the devices operate up to >60C and the light output is polarized in a stable, linear characteristic over all normal operating conditions. The 3dB modulation bandwidth of the devices is in excess of 3GHz and we have demonstrated the operation of a transceiver module operating at 1.25Gb/s over both SI-POF and GI-POF. Ageing experiments carried out using a matrix of current and temperature stress conditions allows us to estimate that the time to failure of 1% of devices (TT1%F) is over 200,000h for reasonable use conditions - making these red VCSELs ready for commercial exploitation in a variety of consumer-type applications. Experiments using appropriate pulsed driving conditions have resulted in operation of 665nm VCSELs at a temperature of 85°C whilst still offering powers useable for eye-safe free space and POF communications.

A race against time: can CO-OPs and provider start-ups survive in the health insurance marketplaces?

PubMed

Eggbeer, Bill

2015-12-01

> The Affordable Care Act's state and federal health insurance marketplaces, designed to provide affordable insurance coverage to individuals and small groups, are proving hostile territory to new market entrants. Efforts to inject competition into the marketplaces are being challenged by the wide-scale withdrawal o consumer-operated and oriented plans (CO-OPs). Meanwhile, premiums appear likely to increase for consumers as plans seek to balance medical losses. Flaws in the "Three R's" (reinsurance, risk corridors, and risk-adjustment) program are viewed as a threat to the survival of CO-OPs and start-ups.

Early chest tube removal after coronary artery bypass graft surgery.

PubMed

Mirmohammad-Sadeghi, Mohsen; Etesampour, Ali; Gharipour, Mojgan; Shariat, Zeinab; Nilforoush, Peyman; Saeidi, Mahmoud; Mackie, Mahsa; Sadeghi, Fatemeh Mirmohamad

2009-12-01

There is no clear data about the optimum time for chest tube removal after coronary artery bypass surgery. The aim of this study was to assess the impact of the chest tube removal time following coronary artery bypass grafting surgery on the clinical outcome of the patients. An analysis of data from 307 patients was performed. The patients were randomized into two groups: in group 1 (N=107) chest tubes were removed within the first 24 hours after surgery, whereas in group 2 (N=200), chest tubes were removed in the second 24 hours after surgery. Demographics, lactate and pH at the beginning, during and after the operation, creatinine, left ventricular ejection fraction, inotropic drugs administration, length of ICU stay, and mortality data were collected. Respiratory rate and pain level was assessed. In these surgeries, the mean± standard deviation for the aortic clamping time was 49.18±17.59 minutes and cardiopulmonary bypass time was 78.39±25.12 minutes. The amount of heparin consumed by the second group was higher (P <0.001) which could be considered as an important factor in increasing the drainage time after the surgery (P =0.047). The pain level evaluated 24 hours post-operation was lower in the first group, and the difference in the pain level between the 2 groups evaluated 30 hours post-operation was significant (P=0.016). The mean time of intensive care unit stay was longer in the second group but it was not statistically significant. Early extracting of chest tubes after coronary artery bypass graft surgery when there is no significant drainage can lead to pain reduction and consuming oxygen is an effective measure after surgery toward healing; it doesn't increase the risk of creation of plural effusion and pericardial effusion.

Wave Engine Technology Development

DTIC Science & Technology

1984-01-01

were the usual minor but time consuming problems of converting a program to run on a new computer with a new operating system and Fortran compiler...Exit Port. - - I _ _- i - - ~ = _ _ o71 - .. (I 00 kfC ) C: 4 03 \\. ft~ d) Ix- 3:- 0r i lzz 𔃾 14- Wave Field 81 and the associated port printouts are

The Case for Sustainable Laboratories: First Steps at Harvard University

ERIC Educational Resources Information Center

Woolliams, Jessica; Lloyd, Matthew; Spengler, John D.

2005-01-01

Purpose: Laboratories typically consume 4-5 times more energy than similarly-sized commercial space. This paper adds to a growing dialogue about how to "green" a laboratory's design and operations. Design/methodology/approach: The paper is divided into three sections. The first section reviews the background and theoretical issues. A…

Multiple view image analysis of freefalling U.S. wheat grains for damage assessment

USDA-ARS?s Scientific Manuscript database

Currently, inspection of wheat in the United States for grade and class is performed by human visual analysis. This is a time consuming operation typically taking several minutes for each sample. Digital imaging research has addressed this issue over the past two decades, with success in recognition...

A Utilization-Focused Approach to Evaluation by a Performance Audit Agency

ERIC Educational Resources Information Center

Perry, Ron; Thomas, Bob; DuBois, Elizabeth; McGowan, Rob

2006-01-01

For years, spending by the King County (Seattle, Washington) corrections department consumed a growing share of the county operating budget, and the department accrued a backlog of needed capital investments. At the same time, there was a history of mistrust between the county council and department management, which centered on whether the…

The Kane Experimental Forest carbon inventory: Carbon reporting with FVS

Treesearch

Coeli Hoover

2008-01-01

As the number of state and regional climate change agreements grows, so does the need to assess the carbon implications of planned forest management actions. At the operational level, producing detailed stock estimates for the primary carbon pools becomes time-consuming and cumbersome. Carbon reporting functionality has been fully integrated within the Forest...

Polybrominated diphenyl ethers (PBDE) in serum: findings from a US cohort of consumers of sport-caught fish.

PubMed

Anderson, Henry A; Imm, Pamela; Knobeloch, Lynda; Turyk, Mary; Mathew, John; Buelow, Carol; Persky, Victoria

2008-09-01

Polybrominated diphenyl ethers (PBDEs) have been used as flame retardants in foams, fabrics and plastics, and are common contaminants of household air and dust and bioaccumulate in wildlife, and are detectable in human tissues and in fish and animal food products. In the Great Lakes Basin sport fish consumption has been demonstrated to be an important source of PCB and DDE exposure. PBDEs are present in the same sport fish but prior to our study the contribution to human PBDE body burdens from Great Lakes sport fish consumption had not been investigated. This study was designed to assess PBDE, PCB and 1,1-bis(4-chlorophenyl)-2,2-dichloroethene (DDE) serum concentrations in an existing cohort of 508 frequent and infrequent consumers of sport-caught fish living in five Great Lake states. BDE congeners 47 and 99 were identified in the majority of blood samples, 98% and 62% respectively. summation operatorPBDE levels were positively associated with age, hours spent outdoors, DDE, summation operatorPCB, years of sportfish consumption, and catfish and shellfish intake, and negatively associated with income and recent weight loss. Other dietary components collected were not predictive of measured summation operatorPBDE levels. In multivariate models, summation operatorPBDE levels were positively associated with age, years consuming sport fish, shellfish meals, and computer use and negatively associated with recent weight loss. Having summation operatorPBDE levels in the highest quintile was independently associated with older age, male gender, consumption of catfish and shellfish, computer use and spending less time indoors. summation operatorPCB and DDE were strongly associated suggesting common exposure routes. The association between summation operatorPBDE and summation operatorPCB or DDE was much weaker and modeling suggested more diverse PBDE sources with few identified multi-contaminant-shared exposure routes. In our cohort Great Lakes sport fish consumption does not contribute strongly to PBDE exposure.

Distributed Optimization of Sustainable Power Dispatch and Flexible Consumer Loads for Resilient Power Grid Operations

NASA Astrophysics Data System (ADS)

Srikantha, Pirathayini

Today's electric grid is rapidly evolving to provision for heterogeneous system components (e.g. intermittent generation, electric vehicles, storage devices, etc.) while catering to diverse consumer power demand patterns. In order to accommodate this changing landscape, the widespread integration of cyber communication with physical components can be witnessed in all tenets of the modern power grid. This ubiquitous connectivity provides an elevated level of awareness and decision-making ability to system operators. Moreover, devices that were typically passive in the traditional grid are now `smarter' as these can respond to remote signals, learn about local conditions and even make their own actuation decisions if necessary. These advantages can be leveraged to reap unprecedented long-term benefits that include sustainable, efficient and economical power grid operations. Furthermore, challenges introduced by emerging trends in the grid such as high penetration of distributed energy sources, rising power demands, deregulations and cyber-security concerns due to vulnerabilities in standard communication protocols can be overcome by tapping onto the active nature of modern power grid components. In this thesis, distributed constructs in optimization and game theory are utilized to design the seamless real-time integration of a large number of heterogeneous power components such as distributed energy sources with highly fluctuating generation capacities and flexible power consumers with varying demand patterns to achieve optimal operations across multiple levels of hierarchy in the power grid. Specifically, advanced data acquisition, cloud analytics (such as prediction), control and storage systems are leveraged to promote sustainable and economical grid operations while ensuring that physical network, generation and consumer comfort requirements are met. Moreover, privacy and security considerations are incorporated into the core of the proposed designs and these serve to improve the resiliency of the future smart grid. It is demonstrated both theoretically and practically that the techniques proposed in this thesis are highly scalable and robust with superior convergence characteristics. These distributed and decentralized algorithms allow individual actuating nodes to execute self-healing and adaptive actions when exposed to changes in the grid so that the optimal operating state in the grid is maintained consistently.

Maintaining Balance: The Increasing Role of Energy Storage for Renewable Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stenclik, Derek; Denholm, Paul; Chalamala, Babu

For nearly a century, global power systems have focused on three key functions: generating, transmitting, and distributing electricity as a real-time commodity. Physics requires that electricity generation always be in real-time balance with load-despite variability in load on time scales ranging from subsecond disturbances to multiyear trends. With the increasing role of variable generation from wind and solar, the retirement of fossil-fuel-based generation, and a changing consumer demand profile, grid operators are using new methods to maintain this balance.

7 CFR 1212.54 - Operating reserve.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING... RESEARCH, PROMOTION, CONSUMER EDUCATION AND INDUSTRY INFORMATION ORDER Honey Packers and Importers Research, Promotion, Consumer Education, and Industry Information Order Expenses and Assessments § 1212.54 Operating...

Meeting Consumers' Information Needs: Putting Research to Work.

ERIC Educational Resources Information Center

Steketee, Drew

The Consumer Information Center is a federal program which encourages federal agencies to develop and release consumer information to the public. It also promotes consumer awareness and access to information through the "Consumer Information Catalog" and a mail order distribution operation. Through research, the Center can learn the…

Two-year survival rates of proximal atraumatic restorative treatment restorations in relation to glass ionomer cements and Postrestoration meals consumed.

PubMed

Kemoli, Arthur Musakulu; Opinya, Gladys N; van Amerongen, Willem Evert; Mwalili, Samuel M

2011-01-01

The purpose of this study was to investigate the influence of 3 glass ionomer cement (GIC) brands and the postrestoration meal consumed on the survival rate of proximal atraumatic restorative treatment (ART) restorations. A total of 804 proximal restorations were placed in primary molars by trained operators and assistants using 3 GIC brands. The materials' mixing/placement times, the room temperature and the postrestoration meal consumed by the subjects were documented. The restorations were evaluated soon after placement and after 2 years by trained and calibrated evaluators. After 2 years, approximately 31% of the restorations had survived. There were no statistically significant differences in the survival rate of the restorations in relation to the GIC brands. The postrestoration meal consumed, which was of "hard consistency," was associated with significantly lower survival rate of the restorations. The survival rate of the proximal restorations was not significantly affected by the glass ionomer cement brands used, but was significantly influenced by the consistency of the next meal consumed by each child.

Investigating the Concept of Consumers as Producers in Virtual Worlds: Looking through Social, Technical, Economic, and Legal Lenses

NASA Astrophysics Data System (ADS)

Kienle, Holger M.; Lober, Andreas; Vasiliu, Crina A.; Müller, Hausi A.

Virtual worlds such as World of Warcraft and Second Life enable consumers as producers, that is users can choose to be passive consumers of content, active producers of content, or both. Consumers as producers poses unique challenges and opportunities for both operators and users of virtual worlds. While the degrees of freedom for user-generated content differ depending on the world, instances of consumers as producers can be found in many virtual worlds. In this paper we characterize consumers as producers with the help of four "lenses"—social, technical, economic, and legal—and use the lenses to discuss implications for operators and users. These lenses provide a complementary analysis of consumers as producers from different angels and shows that an understanding of it requires a holistic approach.

Ground controlled robotic assembly operations for Space Station Freedom

NASA Technical Reports Server (NTRS)

Parrish, Joseph C.

1991-01-01

A number of dextrous robotic systems and associated positioning and transportation devices are available on Space Station Freedom (SSF) to perform assembly tasks that would otherwise need to be performed by extravehicular activity (EVA) crewmembers. The currently planned operating mode for these robotic systems during the assembly phase is teleoperation by intravehicular activity (IVA) crewmembers. While this operating mode is less hazardous and expensive than manned EVA operations, and has insignificant control loop time delays, the amount of IVA time available to support telerobotic operations is much less than the anticipated requirements. Some alternative is needed to allow the robotic systems to perform useful tasks without exhausting the available IVA resources; ground control is one such alternative. The issues associated with ground control of SSF robotic systems to alleviate onboard crew time availability constraints are investigated. Key technical issues include the effect of communication time delays, the need for safe, reliable execution of remote operations, and required modifications to the SSF ground and flight system architecture. Time delay compensation techniques such as predictive displays and world model-based force reflection are addressed and collision detection and avoidance strategies to ensure the safety of the on-orbit crew, Orbiter, and SSF are described. Although more time consuming and difficult than IVA controlled teleoperations or manned EVA, ground controlled telerobotic operations offer significant benefits during the SSF assembly phase, and should be considered in assembly planning activities.

Optimal Reservoir Operation using Stochastic Model Predictive Control

NASA Astrophysics Data System (ADS)

Sahu, R.; McLaughlin, D.

2016-12-01

Hydropower operations are typically designed to fulfill contracts negotiated with consumers who need reliable energy supplies, despite uncertainties in reservoir inflows. In addition to providing reliable power the reservoir operator needs to take into account environmental factors such as downstream flooding or compliance with minimum flow requirements. From a dynamical systems perspective, the reservoir operating strategy must cope with conflicting objectives in the presence of random disturbances. In order to achieve optimal performance, the reservoir system needs to continually adapt to disturbances in real time. Model Predictive Control (MPC) is a real-time control technique that adapts by deriving the reservoir release at each decision time from the current state of the system. Here an ensemble-based version of MPC (SMPC) is applied to a generic reservoir to determine both the optimal power contract, considering future inflow uncertainty, and a real-time operating strategy that attempts to satisfy the contract. Contract selection and real-time operation are coupled in an optimization framework that also defines a Pareto trade off between the revenue generated from energy production and the environmental damage resulting from uncontrolled reservoir spills. Further insight is provided by a sensitivity analysis of key parameters specified in the SMPC technique. The results demonstrate that SMPC is suitable for multi-objective planning and associated real-time operation of a wide range of hydropower reservoir systems.

Multitasking operating systems for microprocessors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cramer, T.

1981-01-01

Microprocessors, because of their low cost, low power consumption, and small size, have caused an explosion in the number of innovative computer applications. Although there is a great deal of variation in microprocessor applications software, there is relatively little variation in the operating-system-level software from one application to the next. Nonetheless, operating system software, especially when multitasking is involved, can be very time consuming and expensive to develop. The major microprocessor manufacturers have acknowledged the need for operating systems in microprocessor applications and are now supplying real-time multitasking operating system software that is adaptable to a wide variety of usermore » systems. Use of this existing operating system software will decrease the number of redundant operating system development efforts, thus freeing programmers to work on more creative and productive problems. This paper discusses the basic terminology and concepts involved with multitasking operating systems. It is intended to provide a general understanding of the subject, so that the reader will be prepared to evaluate specific operating system software according to his or her needs. 2 references.« less

16 CFR 1000.21 - Office of Compliance and Field Operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... enforces the Consumer Product Safety Act reporting requirements. It reviews consumer complaints, conducts.... 1000.21 Section 1000.21 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL COMMISSION... identifying and addressing safety hazards in consumer products already in distribution, promoting industry...

16 CFR 1000.21 - Office of Compliance and Field Operations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... enforces the Consumer Product Safety Act reporting requirements. It reviews consumer complaints, conducts.... 1000.21 Section 1000.21 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL COMMISSION... identifying and addressing safety hazards in consumer products already in distribution, promoting industry...

16 CFR 1000.21 - Office of Compliance and Field Operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... enforces the Consumer Product Safety Act reporting requirements. It reviews consumer complaints, conducts.... 1000.21 Section 1000.21 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL COMMISSION... identifying and addressing safety hazards in consumer products already in distribution, promoting industry...

16 CFR 1000.21 - Office of Compliance and Field Operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... enforces the Consumer Product Safety Act reporting requirements. It reviews consumer complaints, conducts.... 1000.21 Section 1000.21 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL COMMISSION... identifying and addressing safety hazards in consumer products already in distribution, promoting industry...

Developing a space network interface simulator: The NTS approach

NASA Technical Reports Server (NTRS)

Hendrzak, Gary E.

1993-01-01

This paper describes the approach used to redevelop the Network Control Center (NCC) Test System (NTS), a hardware and software facility designed to make testing of the NCC Data System (NCCDS) software efficient, effective, and as rigorous as possible prior to operational use. The NTS transmits and receives network message traffic in real-time. Data transfer rates and message content are strictly controlled and are identical to that of the operational systems. NTS minimizes the need for costly and time-consuming testing with the actual external entities (e.g., the Hubble Space Telescope (HST) Payload Operations Control Center (POCC) and the White Sands Ground Terminal). Discussed are activities associated with the development of the NTS, lessons learned throughout the project's lifecycle, and resulting productivity and quality increases.

Face validity of a pre-clinical model of operant binge drinking: just a question of speed.

PubMed

Jeanblanc, Jérôme; Sauton, Pierre; Jeanblanc, Virginie; Legastelois, Rémi; Echeverry-Alzate, Victor; Lebourgeois, Sophie; Gonzalez-Marin, Maria Del Carmen; Naassila, Mickaël

2018-06-04

Binge drinking (BD) is often defined as a large amount of alcohol consumed in a 'short' period of time or 'per occasion'. In clinical research, few researchers have included the notion of 'speed of drinking' in the definition of BD. Here, we aimed to describe a novel pre-clinical model based on voluntary operant BD, which included both the quantity of alcohol and the rapidity of consumption. In adult Long-Evans male rats, we induced BD by regularly decreasing the duration of ethanol self-administration from 1-hour to 15-minute sessions. We compared the behavioral consequences of BD with the behaviors of rats subjected to moderate drinking or heavy drinking (HD). We found that, despite high ethanol consumption levels (1.2 g/kg/15 minutes), the total amounts consumed were insufficient to differentiate HD from BD. However, consumption speed could distinguish between these groups. The motivation to consume was higher in BD than in HD rats. After BD, we observed alterations in locomotor coordination in rats that consumed greater than 0.8 g/kg, which was rarely observed in HD rats. Finally, chronic BD led to worse performance in a decision-making task, and as expected, we observed a lower stimulated dopaminergic release within nucleus accumbens slices in poor decision makers. Our BD model exhibited good face validity and can now provide animals voluntarily consuming very rapidly enough alcohol to achieve intoxication levels and thus allowing the study of the complex interaction between individual and environmental factors underlying BD behavior. © 2018 Society for the Study of Addiction.

Scale Modeling for the PATRIOT Electromagnetic Pulse Test.

DTIC Science & Technology

1981-05-01

concerned with providing basic in- formation that is either too costly and time consuming or impossible to obtain in a full-scale field operation. This...tar:je’.s.l The missiles are mounted on launching stations that are .4,t pfys;ically w.,nnected to the fire control section kFCS ). Fire contxoi vs mirnt

Military Curricula for Vocational & Technical Education. Petroleum Equipment and Technical Operations, QM0142, 19-5.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

This subcourse containg lesson assignments, lesson texts, and programmed reviews covers the most frequently used equipment for transporting and storing petroleum products from the time they are purchased until they are consumed by the user. The course is one of a number of military-developed curriculum packages selected for adaptation to…

Bottom-Up Influences on Voluntary Task Switching: The Elusive Homunculus Escapes

ERIC Educational Resources Information Center

Yeung, Nick

2010-01-01

Voluntary action can be studied by giving participants free choice over which task to perform in response to each presented stimulus. In such experiments, performance costs are observed when participants choose to switch tasks from the previous trial. It has been proposed that these costs primarily index the time-consuming operation of top-down…

Improving Program Results through the Use of Predictive Operational Performance Indicators: A Canadian Case Study

ERIC Educational Resources Information Center

Barrados, Maria; Blain, J. S.

2013-01-01

In Canada, in-depth evaluations of federal programs are intended to occur every 5 years. As such, evaluation is a periodic retrospective (lag) indicator examining results achieved versus program objectives. In a Canadian context, stand-alone evaluations have proved challenging to implement, time consuming, and not well adapted to annual management…

Testing single point incremental forming moulds for rotomoulding operations

NASA Astrophysics Data System (ADS)

Afonso, Daniel; de Sousa, Ricardo Alves; Torcato, Ricardo

2017-10-01

Low pressure polymer processes as thermoforming or rotational moulding use much simpler moulds than high pressure processes like injection. However, despite the low forces involved in the process, moulds manufacturing for these applications is still a very material, energy and time consuming operation. Particularly in rotational moulding there is no standard for the mould manufacture and very different techniques are applicable. The goal of this research is to develop and validate a method for manufacturing plastically formed sheet metal moulds by single point incremental forming (SPIF) for rotomoulding and rotocasting operations. A Stewart platform based SPIF machine allow the forming of thick metal sheets, granting the required structural stiffness for the mould surface, and keeping a short manufacture lead time and low thermal inertia. The experimental work involves the proposal of a hollow part, design and fabrication of a sheet metal mould using dieless incremental forming techniques and testing its operation in the production of prototype parts.

AEP Ohio gridSMART Demonstration Project Real-Time Pricing Demonstration Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widergren, Steven E.; Subbarao, Krishnappa; Fuller, Jason C.

2014-02-01

This report contributes initial findings from an analysis of significant aspects of the gridSMART® Real-Time Pricing (RTP) – Double Auction demonstration project. Over the course of four years, Pacific Northwest National Laboratory (PNNL) worked with American Electric Power (AEP), Ohio and Battelle Memorial Institute to design, build, and operate an innovative system to engage residential consumers and their end-use resources in a participatory approach to electric system operations, an incentive-based approach that has the promise of providing greater efficiency under normal operating conditions and greater flexibility to react under situations of system stress. The material contained in this report supplementsmore » the findings documented by AEP Ohio in the main body of the gridSMART report. It delves into three main areas: impacts on system operations, impacts on households, and observations about the sensitivity of load to price changes.« less

[MATCHE: Management Approach to Teaching Consumer and Homemaking Education.] Occupational Strand: Foods and Nutrition. Module II-C-2: Operations and Activities of a Food Service Operation.

ERIC Educational Resources Information Center

Waskey, Frank

This competency-based preservice home economics teacher education module on operations and activities of a food service operation is the second in a set of three modules on occupational education relating to foods and nutrition. (This set is part of a larger series of sixty-seven modules on the Management Approach to Teaching Consumer and…

Development of efficient time-evolution method based on three-term recurrence relation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akama, Tomoko, E-mail: a.tomo---s-b-l-r@suou.waseda.jp; Kobayashi, Osamu; Nanbu, Shinkoh, E-mail: shinkoh.nanbu@sophia.ac.jp

The advantage of the real-time (RT) propagation method is a direct solution of the time-dependent Schrödinger equation which describes frequency properties as well as all dynamics of a molecular system composed of electrons and nuclei in quantum physics and chemistry. Its applications have been limited by computational feasibility, as the evaluation of the time-evolution operator is computationally demanding. In this article, a new efficient time-evolution method based on the three-term recurrence relation (3TRR) was proposed to reduce the time-consuming numerical procedure. The basic formula of this approach was derived by introducing a transformation of the operator using the arcsine function.more » Since this operator transformation causes transformation of time, we derived the relation between original and transformed time. The formula was adapted to assess the performance of the RT time-dependent Hartree-Fock (RT-TDHF) method and the time-dependent density functional theory. Compared to the commonly used fourth-order Runge-Kutta method, our new approach decreased computational time of the RT-TDHF calculation by about factor of four, showing the 3TRR formula to be an efficient time-evolution method for reducing computational cost.« less

45 CFR 98.33 - Consumer education.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Consumer education. 98.33 Section 98.33 Public... Program Operations (Child Care Services)-Parental Rights and Responsibilities § 98.33 Consumer education... public consumer education information that will promote informed child care choices including, at a...

45 CFR 98.33 - Consumer education.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Consumer education. 98.33 Section 98.33 Public... Program Operations (Child Care Services)-Parental Rights and Responsibilities § 98.33 Consumer education... public consumer education information that will promote informed child care choices including, at a...

16 CFR § 1000.21 - Office of Compliance and Field Operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... enforces the Consumer Product Safety Act reporting requirements. It reviews consumer complaints, conducts...§ 1000.21 Section § 1000.21 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION GENERAL COMMISSION... identifying and addressing safety hazards in consumer products already in distribution, promoting industry...

Time-driven activity based costing of total knee replacement surgery at a London teaching hospital.

PubMed

Chen, Alvin; Sabharwal, Sanjeeve; Akhtar, Kashif; Makaram, Navnit; Gupte, Chinmay M

2015-12-01

The aim of this study was to conduct a time-driven activity based costing (TDABC) analysis of the clinical pathway for total knee replacement (TKR) and to determine where the major cost drivers lay. The in-patient pathway was prospectively mapped utilising a TDABC model, following 20 TKRs. The mean age for these patients was 73.4 years. All patients were ASA grade I or II and their mean BMI was 30.4. The 14 varus knees had a mean deformity of 5.32° and the six valgus knee had a mean deformity of 10.83°. Timings were prospectively collected as each patient was followed through the TKR pathway. Pre-operative costs including pre-assessment and joint school were £ 163. Total staff costs for admission and the operating theatre were £ 658. Consumables cost for the operating theatre were £ 1862. The average length of stay was 5.25 days at a total cost of £ 910. Trust overheads contributed £ 1651. The overall institutional cost of a 'noncomplex' TKR in patients without substantial medical co-morbidities was estimated to be £ 5422, representing a profit of £ 1065 based on a best practice tariff of £ 6487. The major cost drivers in the TKR pathway were determined to be theatre consumables, corporate overheads, overall ward cost and operating theatre staffing costs. Appropriate discounting of implant costs, reduction in length of stay by adopting an enhanced recovery programme and control of corporate overheads through the use of elective orthopaedic treatment centres are proposed approaches for reducing the overall cost of treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

Automated Interactive Simulation Model (AISIM) VAX Version 5.0 Training Manual.

DTIC Science & Technology

1987-05-29

action, activity, decision , etc. that consumes time. The entity is automatically created by the system when an ACTION Primitive is placed. 1.3.2.4 The...MODELED SYSTEM 1.3.2.1 The Process Entity. A Process is used to represent the operations, decisions , actions or activities that can be decomposed and...is associated with the Action entity described below, is included in Process definitions to indicate the time a certain Action (or process, decision

Protection for the Consumer; Business Education: 6463.07.

ERIC Educational Resources Information Center

Finora, Daniel

This course is designed to acquaint the student with the functions, criticisms, costs, and consumer analysis of advertising; Federal and State regulations of industry operation and advertising; Federal, State, and city agencies for consumer protection; private and business-sponsored organizations for consumer protection; and rights and…

Finite element methods on supercomputers - The scatter-problem

NASA Technical Reports Server (NTRS)

Loehner, R.; Morgan, K.

1985-01-01

Certain problems arise in connection with the use of supercomputers for the implementation of finite-element methods. These problems are related to the desirability of utilizing the power of the supercomputer as fully as possible for the rapid execution of the required computations, taking into account the gain in speed possible with the aid of pipelining operations. For the finite-element method, the time-consuming operations may be divided into three categories. The first two present no problems, while the third type of operation can be a reason for the inefficient performance of finite-element programs. Two possibilities for overcoming certain difficulties are proposed, giving attention to a scatter-process.

Consumer-Operated Service Programs: monetary and donated costs and cost-effectiveness.

PubMed

Yates, Brian T; Mannix, Danyelle; Freed, Michael C; Campbell, Jean; Johnsen, Matthew; Jones, Kristine; Blyler, Crystal R

2011-01-01

Examine cost differences between Consumer Operated Service Programs (COSPs) as possibly determined by a) size of program, b) use of volunteers and other donated resources, c) cost-of-living differences between program locales, d) COSP model applied, and e) delivery system used to implement the COSP model. As part of a larger evaluation of COSP, data on operating costs, enrollments, and mobilization of donated resources were collected for eight programs representing three COSP models (drop-in centers, mutual support, and education/advocacy training). Because the 8 programs were operated in geographically diverse areas of the US, costs were examined with and without adjustment for differences in local cost of living. Because some COSPs use volunteers and other donated resources, costs were measured with and without these resources being monetized. Scale of operation also was considered as a mediating variable for differences in program costs. Cost per visit, cost per consumer per quarter, and total program cost were calculated separately for funds spent and for resources donated for each COSP. Differences between COSPs in cost per consumer and cost per visit seem better explained by economies of scale and delivery system used than by cost-of-living differences between program locations or COSP model. Given others' findings that different COSP models produce little variation in service effectiveness, minimize service costs by maximizing scale of operation while using a delivery system that allows staff and facilities resources to be increased or decreased quickly to match number of consumers seeking services.

Military Influence Operations: Review of the Consumer Psychology Literature

DTIC Science & Technology

2008-11-01

behaviour research. Research in the area of consumer psychology is concerned with the relationship between people (either individuals or groups) and the...question by reviewing 20 articles from the domain of consumer psychology and consumer behaviour research.2 1.2 Search Strategies and Findings In keeping...and the products and services that they use. A prominent emphasis within the area of consumer psychology is the study of consumer behaviour

A Marine Corps Logistician Examines Logistics Planning and Execution During Operation OVERLORD: A Study in Effectiveness and Implications for Today

DTIC Science & Technology

2013-03-05

the Allies would attack to the east towards Paris . The operation was to conclude on D+90 at which time the Allied force would have taken Paris ... Paris . Despite the fact that the Germans sustained severe casualties in the Falaise pocket in mid-August 1944, the decision by SHAEF to forego the...forces becoming bogged down in Normandy and consuming much more ammunition than had originally been planned for by COMZ.33 After the TUSAG breakout

75 FR 30014 - Consumers Energy Company; Notice of Baseline Filing

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR10-25-000] Consumers Energy Company; Notice of Baseline Filing May 21, 2010. Take notice that on May 17, 2010, Consumers Energy Company (Consumers) submitted a baseline filing of its Statement of Operating Conditions for the...

Simulation of Propellant Loading System Senior Design Implement in Computer Algorithm

NASA Technical Reports Server (NTRS)

Bandyopadhyay, Alak

2010-01-01

Propellant loading from the Storage Tank to the External Tank is one of the very important and time consuming pre-launch ground operations for the launch vehicle. The propellant loading system is a complex integrated system involving many physical components such as the storage tank filled with cryogenic fluid at a very low temperature, the long pipe line connecting the storage tank with the external tank, the external tank along with the flare stack, and vent systems for releasing the excess fuel. Some of the very important parameters useful for design purpose are the prediction of pre-chill time, loading time, amount of fuel lost, the maximum pressure rise etc. The physics involved for mathematical modeling is quite complex due to the fact the process is unsteady, there is phase change as some of the fuel changes from liquid to gas state, then conjugate heat transfer in the pipe walls as well as between solid-to-fluid region. The simulation is very tedious and time consuming too. So overall, this is a complex system and the objective of the work is student's involvement and work in the parametric study and optimization of numerical modeling towards the design of such system. The students have to first become familiar and understand the physical process, the related mathematics and the numerical algorithm. The work involves exploring (i) improved algorithm to make the transient simulation computationally effective (reduced CPU time) and (ii) Parametric study to evaluate design parameters by changing the operational conditions

Proportional reasoning as a heuristic-based process: time constraint and dual task considerations.

PubMed

Gillard, Ellen; Van Dooren, Wim; Schaeken, Walter; Verschaffel, Lieven

2009-01-01

The present study interprets the overuse of proportional solution methods from a dual process framework. Dual process theories claim that analytic operations involve time-consuming executive processing, whereas heuristic operations are fast and automatic. In two experiments to test whether proportional reasoning is heuristic-based, the participants solved "proportional" problems, for which proportional solution methods provide correct answers, and "nonproportional" problems known to elicit incorrect answers based on the assumption of proportionality. In Experiment 1, the available solution time was restricted. In Experiment 2, the executive resources were burdened with a secondary task. Both manipulations induced an increase in proportional answers and a decrease in correct answers to nonproportional problems. These results support the hypothesis that the choice for proportional methods is heuristic-based.

Comparison of Stereotactic and Ultrasound-guided Biopsy of Solid Supratentorial Tumor: A Preliminary Report

PubMed Central

Satyarthee, Guru Dutta; Chandra, P. Sarat; Sharma, Bhawani S.; Mehta, V. S.

2017-01-01

Introduction: The computed tomography (CT) guided stereotactic biopsy (STB) is considered as method of choice for biopsy of intracranial mass lesions. However, it's disadvantages are frame fixation, time requirement for transportation between CT scan suit to the operation theater with added much higher equipment cost in the relatively resource scarred developing country. Ultrasound-guided biopsy (USGB) is relatively simpler, economical, less time consuming, and real-time procedure. Clinical Materials and Methods: Thirty-seven consecutively admitted patients with supratentorial brain tumors, who underwent biopsy of the lesion using CT compatible stereotactic and ultrasound-guided (USGB) procedure formed cohort of the study. Based on location and size of the lesions, the cases were divided into two groups, superficial and deep. Twenty-two patients underwent ultrasound-guided biopsy and 15 with STB. Results: The diagnostic yield of STB was 93% and 91% for ultrasound-guided biopsy. The mean operation time of STB group was 149.00 min and 94 min for USGB, which was statistically significant. Two cases in each group developed hematoma; however, one case in USGB group needed surgical evacuation. The real-time monitoring detected two hematoma intraoperatively, which were further also confirmed on postoperative CT scan head. Conclusions: The ultrasound-guided biopsy procedure (USGB) was simple, relatively shorter time-consuming procedure and equally efficacious and utilizing economical equipment and can act as a safer alternative to CT STB process for biopsy of the intracranial mass lesion. Furthermore, USGB also provided intra-operative real-time monitoring, which provided clue for close monitoring in the postoperative period after completion of biopsy to look for development of fresh hematoma development not only at the biopsy site but also along the biopsy track and adjoining area. Perhaps, a longer period of ultrasonic monitoring following the procedure would be of greater help to detect hematoma formation, which is one of the most common complications of the biopsy procedure. PMID:29114280

Brief Report: Consistency of Search Engine Rankings for Autism Websites

ERIC Educational Resources Information Center

Reichow, Brian; Naples, Adam; Steinhoff, Timothy; Halpern, Jason; Volkmar, Fred R.

2012-01-01

The World Wide Web is one of the most common methods used by parents to find information on autism spectrum disorders and most consumers find information through search engines such as Google or Bing. However, little is known about how the search engines operate or the consistency of the results that are returned over time. This study presents the…

Impacts of demand response and renewable generation in electricity power market

NASA Astrophysics Data System (ADS)

Zhao, Zhechong

This thesis presents the objective of the research which is to analyze the impacts of uncertain wind power and demand response on power systems operation and power market clearing. First, in order to effectively utilize available wind generation, it is usually given the highest priority by assigning zero or negative energy bidding prices when clearing the day-ahead electric power market. However, when congestion occurs, negative wind bidding prices would aggravate locational marginal prices (LMPs) to be negative in certain locations. A load shifting model is explored to alleviate possible congestions and enhance the utilization of wind generation, by shifting proper amount of load from peak hours to off peaks. The problem is to determine proper amount of load to be shifted, for enhancing the utilization of wind generation, alleviating transmission congestions, and making LMPs to be non-negative values. The second piece of work considered the price-based demand response (DR) program which is a mechanism for electricity consumers to dynamically manage their energy consumption in response to time-varying electricity prices. It encourages consumers to reduce their energy consumption when electricity prices are high, and thereby reduce the peak electricity demand and alleviate the pressure to power systems. However, it brings additional dynamics and new challenges on the real-time supply and demand balance. Specifically, price-sensitive DR load levels are constantly changing in response to dynamic real-time electricity prices, which will impact the economic dispatch (ED) schedule and in turn affect electricity market clearing prices. This thesis adopts two methods for examining the impacts of different DR price elasticity characteristics on the stability performance: a closed-loop iterative simulation method and a non-iterative method based on the contraction mapping theorem. This thesis also analyzes the financial stability of DR load consumers, by incorporating explicit LMP formulations and consumer payment requirements into the network-constrained unit commitment (NCUC) problem. The proposed model determines the proper amount of DR loads to be shifted from peak hours to off-peaks under ISO's direct load control, for reducing the operation cost and ensuring that consumer payments of DR loads will not deteriorate significantly after load shifting. Both MINLP and MILP models are discussed, and improved formulation strategies are presented.

76 FR 4907 - The Consumer Operated and Oriented Plan (CO-OP) Advisory Board, February 7, 2011

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-27

... DEPARTMENT OF HEALTH AND HUMAN SERVICES [OCIIO-9978-N] The Consumer Operated and Oriented Plan (CO... Department's strategy to foster the creation of qualified nonprofit health insurance issuers. Specifically... Oversight (OCIIO) on the Department's strategy to foster the creation of qualified nonprofit health...

New fixation method for maxillary distraction osteogenesis using locking attachments.

PubMed

Suzuki, Eduardo Yugo; Buranastidporn, Boonsiva; Ishii, Masatoshi

2006-10-01

The external traction hooks of the intraoral splint used in the rigid external distraction (RED) system for maxillary distraction osteogenesis interfere with the surgical procedures. The purpose of this study is to introduce an innovative splint fixation method for maxillary distraction osteogenesis with Locking Attachments and evaluate their advantages, such as reduction of operating time compared with the traditional intraoral splint method. Retrospective comparison of operative times of maxillary Le Fort I osteotomy procedures was carried out with the traditional protocol using the intraoral splint cemented to the maxillary dentition (n = 14), and a removable intraoral splint that is inserted postsurgically (n = 14). Operative procedure times were compared and analyzed statistically using the data extracted from the surgical records. There were no complications inserting the removable splint postsurgically, including pain, discomfort, or time-consuming procedure. Stable and secure splint fixation was obtained before the distraction procedure and the desired treatment goals were obtained in all patients. The total operative procedure times were significantly reduced in the Locking Attachments group by 24% to 41% (approximately 65 minutes) compared with earlier operations involving the conventional splints (P < .05). Maxillary distraction osteogenesis with the Locking Attachments is a highly effective fixation approach to manage severe hypoplastic maxilla, eliminating lip constraints resulting from scarring and allowing for easier, more deliberate and careful dissection. The use of the Locking Attachments is reliable in craniofacial surgery and has proved to be advantageous in the reduction of the operating time and surgical risks.

A proximity algorithm accelerated by Gauss-Seidel iterations for L1/TV denoising models

NASA Astrophysics Data System (ADS)

Li, Qia; Micchelli, Charles A.; Shen, Lixin; Xu, Yuesheng

2012-09-01

Our goal in this paper is to improve the computational performance of the proximity algorithms for the L1/TV denoising model. This leads us to a new characterization of all solutions to the L1/TV model via fixed-point equations expressed in terms of the proximity operators. Based upon this observation we develop an algorithm for solving the model and establish its convergence. Furthermore, we demonstrate that the proposed algorithm can be accelerated through the use of the componentwise Gauss-Seidel iteration so that the CPU time consumed is significantly reduced. Numerical experiments using the proposed algorithm for impulsive noise removal are included, with a comparison to three recently developed algorithms. The numerical results show that while the proposed algorithm enjoys a high quality of the restored images, as the other three known algorithms do, it performs significantly better in terms of computational efficiency measured in the CPU time consumed.

47 CFR 76.630 - Compatibility with consumer electronics equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Compatibility with consumer electronics equipment. 76.630 Section 76.630 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Compatibility with consumer electronics equipment. (a) Cable system operators shall not scramble or otherwise...

47 CFR 76.630 - Compatibility with consumer electronics equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Compatibility with consumer electronics equipment. 76.630 Section 76.630 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Compatibility with consumer electronics equipment. (a) Cable system operators shall not scramble or otherwise...

47 CFR 76.630 - Compatibility with consumer electronics equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Compatibility with consumer electronics equipment. 76.630 Section 76.630 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Compatibility with consumer electronics equipment. (a) Cable system operators shall not scramble or otherwise...

47 CFR 76.630 - Compatibility with consumer electronics equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Compatibility with consumer electronics equipment. 76.630 Section 76.630 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Compatibility with consumer electronics equipment. (a) Cable system operators shall not scramble or otherwise...

47 CFR 76.630 - Compatibility with consumer electronics equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Compatibility with consumer electronics equipment. 76.630 Section 76.630 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Compatibility with consumer electronics equipment. (a) Cable system operators shall not scramble or otherwise...

A comparison of septal stapler to suture closure in septoplasty: a prospective, randomized trial evaluating the effect on operative time.

PubMed

Sowerby, Leigh J; Wright, Erin D

2013-11-01

Septoplasty requires coaptation of the mucosal flaps at the conclusion of the procedure; classically this is done with nasal packing. Quilting sutures provide a welcome alternative to packing, but can be time-consuming to place. A septal stapler has recently been developed that provides a rapid alternative to quilting sutures but the timesaving has not been quantified. This study was a prospective, randomized trial comparing a septal stapler to quilting suture for coaptation of mucosal flaps in septoplasty. After meeting inclusion criteria, patients underwent septoplasty and inferior turbinoplasty. The total operative time, surgical segment times, including time for closure was recorded. Preoperative and postoperative Nasal Obstruction Symptom Evaluation (NOSE) scores were recorded. A sample size of 16 was determined to detect a difference of 5 minutes in closure time. A total of 16 patients were enrolled in the study. The mean time for closure with septal stapler was 35 ± 22 seconds vs 7 minutes ± 1 minute 10 seconds for suture closure (p < 0.0001). The mean total operative time using the septal stapler was 28 minutes ± 6 minutes whereas 43 minutes ± 13 minutes was required for suture (p = 0.014). No difference in postoperative complications or mucosal healing was seen; preoperative and postoperative improvement in NOSE scores was comparable. Coaptation of the mucosal flaps in septoplasty with a septal stapler affords a timesaving in the operating room with no difference in operative outcome. © 2013 ARS-AAOA, LLC.

Field Scale Testing of RESOLVE at 2010 ISRU Analog Test

NASA Technical Reports Server (NTRS)

Captain, Janine E.; Quinn, J. W.; Moss, T. J.; Weis, K. H.

2010-01-01

When mankind returns to the moon, there will be one aspect of the architecture that will totally change how we explore the solar system. For the first time in space exploration, we will take the initial steps towards breaking our reliance on Earth-supplied consumables by extracting resources from planetary bodies. Our first efforts in this area, known as In Situ Resource Utilization (ISRU), will be directed at extracting some of the abundant oxygen found in the lunar regolith. But the "holy grail" of lunar ISRU will be finding an exploitable source of lunar hydrogen. If we can find a source of hydrogen that can be reasonably extracted from the regolith, it would provide a foundation for true independence from Earth consumables. With in-situ hydrogen and oxygen (and/or water) we can produce many of the major consumables needed to travel to and operate on a sustainable lunar outpost. We would have water to drink, oxygen to breath, and rocket propellants and fuel cell reagents to enable extended access and operations across the moon. NASA initiated development of an experiment package named RESOLVE (Regolith & Environment Science and Oxygen & Lunar Volatile Extraction) that could be flown to the rim or into a permanently shadowed crater to answer the questions surrounding elevated hydrogen at the lunar poles.

Extensions to the Parallel Real-Time Artificial Intelligence System (PRAIS) for fault-tolerant heterogeneous cycle-stealing reasoning

NASA Technical Reports Server (NTRS)

Goldstein, David

1991-01-01

Extensions to an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS) are discussed. PRAIS strives for transparently parallelizing production (rule-based) systems, even under real-time constraints. PRAIS accomplished these goals (presented at the first annual C Language Integrated Production System (CLIPS) conference) by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors. Results using the original PRAIS architecture over a network of Sun 3's, Sun 4's and VAX's are presented. Mechanisms using the producer-consumer model to extend the architecture for fault-tolerance and distributed truth maintenance initiation are also discussed.

Transient-Free Operations With Physics-Based Real-time Analysis and Control

NASA Astrophysics Data System (ADS)

Kolemen, Egemen; Burrell, Keith; Eggert, William; Eldon, David; Ferron, John; Glasser, Alex; Humphreys, David

2016-10-01

In order to understand and predict disruptions, the two most common methods currently employed in tokamak analysis are the time-consuming ``kinetic EFITs,'' which are done offline with significant human involvement, and the search for correlations with global precursors using various parameterization techniques. We are developing automated ``kinetic EFITs'' at DIII-D to enable calculation of the stability as the plasma evolves close to the disruption. This allows us to quantify the probabilistic nature of the stability calculations and provides a stability metric for all possible linear perturbations to the plasma. This study also provides insight into how the control system can avoid the unstable operating space, which is critical for high-performance operations close to stability thresholds at ITER. A novel, efficient ideal stability calculation method and new real-time CER acquisition system are being developed, and a new 77-core server has been installed on the DIII-D PCS to enable experimental use. Sponsored by US DOE under DE-SC0015878 and DE-FC02-04ER54698.

Computer systems for automatic earthquake detection

USGS Publications Warehouse

Stewart, S.W.

1974-01-01

U.S Geological Survey seismologists in Menlo park, California, are utilizing the speed, reliability, and efficiency of minicomputers to monitor seismograph stations and to automatically detect earthquakes. An earthquake detection computer system, believed to be the only one of its kind in operation, automatically reports about 90 percent of all local earthquakes recorded by a network of over 100 central California seismograph stations. The system also monitors the stations for signs of malfunction or abnormal operation. Before the automatic system was put in operation, all of the earthquakes recorded had to be detected by manually searching the records, a time-consuming process. With the automatic detection system, the stations are efficiently monitored continuously. 

International Trade: Rules of Origin

DTIC Science & Technology

2009-03-06

products has been subcontracted to a global manufacturing company that operates in many countries. While some major retailers and brand -name distributors...often the case in today’s global trading environment—determining origin can be a very complex, sometimes subjective, and time-consuming process. U.S...CBP origin determinations, and the effects of the global manufacturing process on ROO. Third, we conclude with some alternatives and options that

Survey of U.S. Ancillary Services Markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Zhi; Levin, Todd; Conzelmann, Guenter

2016-01-01

In addition to providing energy to end-consumers, power system operators are also responsible for ensuring system reliability. To this end, power markets maintain an array of ancillary services to ensure it is always possible to balance the supply and demand for energy in real-time. A subset of these ancillary services are commonly procured through market-based mechanisms: namely, Regulation, Spinning, and Non-spinning Reserves.

7 CFR 1260.169 - Promotion, research, consumer information and industry information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... industry information. 1260.169 Section 1260.169 Agriculture Regulations of the Department of Agriculture... Operating Committee § 1260.169 Promotion, research, consumer information and industry information. The... approval any plans and projects for promotion, research, consumer information and industry information...

7 CFR 1260.169 - Promotion, research, consumer information and industry information.

Code of Federal Regulations, 2011 CFR

2011-01-01

... industry information. 1260.169 Section 1260.169 Agriculture Regulations of the Department of Agriculture... Operating Committee § 1260.169 Promotion, research, consumer information and industry information. The... approval any plans and projects for promotion, research, consumer information and industry information...

7 CFR 1260.169 - Promotion, research, consumer information and industry information.

Code of Federal Regulations, 2012 CFR

2012-01-01

... industry information. 1260.169 Section 1260.169 Agriculture Regulations of the Department of Agriculture... Operating Committee § 1260.169 Promotion, research, consumer information and industry information. The... approval any plans and projects for promotion, research, consumer information and industry information...

7 CFR 1260.169 - Promotion, research, consumer information and industry information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... industry information. 1260.169 Section 1260.169 Agriculture Regulations of the Department of Agriculture... Operating Committee § 1260.169 Promotion, research, consumer information and industry information. The... approval any plans and projects for promotion, research, consumer information and industry information...

A Hands-on Approach to the Teaching of Consumer Affairs.

ERIC Educational Resources Information Center

de Ruyter, Ko; Widdows, Richard

1992-01-01

In a course titled Computerized Consumer Responses and Information Systems, Purdue University students operate a consumer hotline for their school. They must promote its existence, answer calls, develop reports, produce training manuals, and set parameters for the computer system. (SK)

Formulation of consumables management models: Mission planning processor payload interface definition

NASA Technical Reports Server (NTRS)

Torian, J. G.

1977-01-01

Consumables models required for the mission planning and scheduling function are formulated. The relation of the models to prelaunch, onboard, ground support, and postmission functions for the space transportation systems is established. Analytical models consisting of an orbiter planning processor with consumables data base is developed. A method of recognizing potential constraint violations in both the planning and flight operations functions, and a flight data file storage/retrieval of information over an extended period which interfaces with a flight operations processor for monitoring of the actual flights is presented.

The Virtual Test Bed Project

NASA Technical Reports Server (NTRS)

Rabelo, Luis C.

2002-01-01

This is a report of my activities as a NASA Fellow during the summer of 2002 at the NASA Kennedy Space Center (KSC). The core of these activities is the assigned project: the Virtual Test Bed (VTB) from the Spaceport Engineering and Technology Directorate. The VTB Project has its foundations in the NASA Ames Research Center (ARC) Intelligent Launch & Range Operations program. The objective of the VTB project is to develop a new and unique collaborative computing environment where simulation models can be hosted and integrated in a seamless fashion. This collaborative computing environment will be used to build a Virtual Range as well as a Virtual Spaceport. This project will work as a technology pipeline to research, develop, test and validate R&D efforts against real time operations without interfering with the actual operations or consuming the operational personnel s time. This report will also focus on the systems issues required to conceptualize and provide form to a systems architecture capable of handling the different demands.

Consumer diversity across kingdoms supports multiple functions in a coastal ecosystem

PubMed Central

Hensel, Marc J. S.; Silliman, Brian R.

2013-01-01

The global biodiversity crisis impairs the valuable benefits ecosystems provide humans. These nature-generated benefits are defined by a multitude of different ecosystem functions that operate simultaneously. Although several studies have simulated species loss in communities and tracked the response of single functions such as productivity or nutrient cycling, these studies have involved relatively similar taxa, and seldom are strikingly different functions examined. With the exception of highly managed ecosystems such as agricultural fields, rarely are we interested in only one function being performed well. Instead, we rely on ecosystems to deliver several different functions at the same time. Here, we experimentally investigated the extinction impacts of dominant consumers in a salt marsh. These consumers are remarkably phylogenetically diverse, spanning two kingdoms (i.e., Animalia and Fungi). Our field studies reveal that a diverse consumer assemblage significantly enhances simultaneous functioning of disparate ecosystem processes (i.e., productivity, decomposition, and infiltration). Extreme functional and phylogenetic differences among consumers underlie this relationship. Each marsh consumer affected at least one different ecosystem function, and each individual function was affected by no more than two consumers. The implications of these findings are profound: If we want ecosystems to perform many different functions well, it is not just number of species that matter. Rather, the presence of species representing markedly different ecologies and biology is also essential to maximizing multiple functions. Moreover, this work emphasizes the need to incorporate both microcomponents and macrocomponents of food webs to accurately predict biodiversity declines on integrated-ecosystem functioning. PMID:24297926

Millimeter-wave irradiation heating for operation of doped CeO2 electrolyte-supported single solid oxide fuel cell

NASA Astrophysics Data System (ADS)

Che Abdullah, Salmie Suhana Binti; Teranishi, Takashi; Hayashi, Hidetaka; Kishimoto, Akira

2018-01-01

High operation temperature of solid oxide fuel cell (SOFC) results in high cell and operation cost, time consuming and fast cell degradation. Developing high performance SOFC that operates at lower temperature is required. Here we demonstrate 24 GHz microwave as a rapid heating source to replace conventional heating method for SOFC operation using 20 mol% Sm doped CeO2 electrolyte-supported single cell. The tested cell shows improvement of 62% in maximum power density at 630 °C under microwave heating. This improvement governs by bulk conductivity of the electrolyte. Investigation of ionic transference number reveals that the value is unchanged under microwave irradiation, confirming the charge carrier is dominated by oxygen ion species. This work shows a potential new concept of high performance as well as cost and energy effective SOFC.

Magellan Project: Evolving enhanced operations efficiency to maximize science value

NASA Technical Reports Server (NTRS)

Cheuvront, Allan R.; Neuman, James C.; Mckinney, J. Franklin

1994-01-01

Magellan has been one of NASA's most successful spacecraft, returning more science data than all planetary spacecraft combined. The Magellan Spacecraft Team (SCT) has maximized the science return with innovative operational techniques to overcome anomalies and to perform activities for which the spacecraft was not designed. Commanding the spacecraft was originally time consuming because the standard development process was envisioned as manual tasks. The Program understood that reducing mission operations costs were essential for an extended mission. Management created an environment which encouraged automation of routine tasks, allowing staff reduction while maximizing the science data returned. Data analysis and trending, command preparation, and command reviews are some of the tasks that were automated. The SCT has accommodated personnel reductions by improving operations efficiency while returning the maximum science data possible.

75 FR 27256 - Implementation of Section 304 of the Telecommunications Act of 1996: Commercial Availability of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-14

... Availability of Navigation Devices; Compatibility Between Cable Systems and Consumer Electronics Equipment... cable operators and the consumer electronics industry to establish the technical details of the... Cable and Telecommunications Association and the Consumer Electronics Association had agreed in a...

Novel handheld x-ray fluorescence spectrometer for routine testing for the presence of lead

NASA Astrophysics Data System (ADS)

Rensing, Noa M.; Tiernan, Timothy C.; Squillante, Michael R.

2011-06-01

RMD is developing a safe, inexpensive, and easy to operate lead detector for retailers and consumers that can reliably detect dangerous levels of lead in toys and other household products. Lead and its compounds have been rated as top chemicals that pose a great threat to human health. However, widespread testing for environmental lead is rarely undertaken until lead poisoning has already been diagnosed. The problem is not due to the accuracy or sensitivity of existing lead detection technology, but rather to the high expense, safety and licensing barriers of available test equipment. An inexpensive and easy to use lead detector would enable the identification of highly contaminated objects and areas and allow for timely and cost effective remediation. The military has similar needs for testing for lead and other heavy elements such as mercury, primarily in the decontamination of former military properties prior to their return to civilian use. RMD's research and development efforts are abased on advanced solid-state detectors combined with recently patented lead detection techniques to develop a consumer oriented lead detector that will be widely available and easy and inexpensive to use. These efforts will result in an instrument that offers: (1) high sensitivity, to identify objects containing dangerous amounts of lead, (2) low cost to encourage widespread testing by consumers and other end users and (3) convenient operation requiring no training or licensing. In contrast, current handheld x-ray fluorescence spectrometers either use a radioactive source requiring licensing and operating training, or use an electronic x-ray source that limits their sensitivity to surface lead.

Low cost and compact quantum key distribution

NASA Astrophysics Data System (ADS)

Duligall, J. L.; Godfrey, M. S.; Harrison, K. A.; Munro, W. J.; Rarity, J. G.

2006-10-01

We present the design of a novel free-space quantum cryptography system, complete with purpose-built software, that can operate in daylight conditions. The transmitter and receiver modules are built using inexpensive off-the-shelf components. Both modules are compact allowing the generation of renewed shared secrets on demand over a short range of a few metres. An analysis of the software is shown as well as results of error rates and therefore shared secret yields at varying background light levels. As the system is designed to eventually work in short-range consumer applications, we also present a use scenario where the consumer can regularly 'top up' a store of secrets for use in a variety of one-time-pad (OTP) and authentication protocols.

Mid-infrared spectroscopy and chemometrics in corn starch classification

NASA Astrophysics Data System (ADS)

Dupuy, N.; Wojciechowski, C.; Ta, C. D.; Huvenne, J. P.; Legrand, P.

1997-06-01

The authentication of food is a very important issue for both the consumer and the food industry at all levels of the food chain from raw materials to finished products. Corn starch can be used in a wide variety of food preparations such as bakery cream fillings, sauces, salad dressings, frozen foods etc. Many modifications are made to corn starch in connection with its use in agrofood. The value of the product increases with the degree of modification. Some chemical and physical tests have been devised to solve the problem of identifying these modifications but all the methods are time consuming and require skilled operators. We separate corn starches into groups related to their modification on the basis of the infrared spectra.

Optimum load distribution between heat sources based on the Cournot model

NASA Astrophysics Data System (ADS)

Penkovskii, A. V.; Stennikov, V. A.; Khamisov, O. V.

2015-08-01

One of the widespread models of the heat supply of consumers, which is represented in the "Single buyer" format, is considered. The methodological base proposed for its description and investigation presents the use of principles of the theory of games, basic propositions of microeconomics, and models and methods of the theory of hydraulic circuits. The original mathematical model of the heat supply system operating under conditions of the "Single buyer" organizational structure provides the derivation of a solution satisfying the market Nash equilibrium. The distinctive feature of the developed mathematical model is that, along with problems solved traditionally within the bounds of bilateral relations of heat energy sources-heat consumer, it considers a network component with its inherent physicotechnical properties of the heat network and business factors connected with costs of the production and transportation of heat energy. This approach gives the possibility to determine optimum levels of load of heat energy sources. These levels provide the given heat energy demand of consumers subject to the maximum profit earning of heat energy sources and the fulfillment of conditions for formation of minimum heat network costs for a specified time. The practical realization of the search of market equilibrium is considered by the example of a heat supply system with two heat energy sources operating on integrated heat networks. The mathematical approach to the solution search is represented in the graphical form and illustrates computations based on the stepwise iteration procedure for optimization of levels of loading of heat energy sources (groping procedure by Cournot) with the corresponding computation of the heat energy price for consumers.

Precise time and time interval applications to electric power systems

NASA Technical Reports Server (NTRS)

Wilson, Robert E.

1992-01-01

There are many applications of precise time and time interval (frequency) in operating modern electric power systems. Many generators and customer loads are operated in parallel. The reliable transfer of electrical power to the consumer partly depends on measuring power system frequency consistently in many locations. The internal oscillators in the widely dispersed frequency measuring units must be syntonized. Elaborate protection and control systems guard the high voltage equipment from short and open circuits. For the highest reliability of electric service, engineers need to study all control system operations. Precise timekeeping networks aid in the analysis of power system operations by synchronizing the clocks on recording instruments. Utility engineers want to reproduce events that caused loss of service to customers. Precise timekeeping networks can synchronize protective relay test-sets. For dependable electrical service, all generators and large motors must remain close to speed synchronism. The stable response of a power system to perturbations is critical to continuity of electrical service. Research shows that measurement of the power system state vector can aid in the monitoring and control of system stability. If power system operators know that a lightning storm is approaching a critical transmission line or transformer, they can modify operating strategies. Knowledge of the location of a short circuit fault can speed the re-energizing of a transmission line. One fault location technique requires clocks synchronized to one microsecond. Current research seeks to find out if one microsecond timekeeping can aid and improve power system control and operation.

Maintaining Balance: The Increasing Role of Energy Storage for Renewable Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stenclik, Derek; Denholm, Paul; Chalamala, Babu

For nearly a century, global power systems have focused on three key functions: to generate, transmit, and distribute electricity as a real-time commodity. Physics requires that electricity generation always be in real-time balance with load, despite variability in load on timescales ranging from sub-second disturbances to multi-year trends. With the increasing role of variable generation from wind and solar, retirements of fossil fuel-based generation, and a changing consumer demand profile, grid operators are using new methods to maintain this balance.

Charge scheduling of an energy storage system under time-of-use pricing and a demand charge.

PubMed

Yoon, Yourim; Kim, Yong-Hyuk

2014-01-01

A real-coded genetic algorithm is used to schedule the charging of an energy storage system (ESS), operated in tandem with renewable power by an electricity consumer who is subject to time-of-use pricing and a demand charge. Simulations based on load and generation profiles of typical residential customers show that an ESS scheduled by our algorithm can reduce electricity costs by approximately 17%, compared to a system without an ESS and by 8% compared to a scheduling algorithm based on net power.

A 2x2 W-Band Reference Time-Shifted Phase-Locked Transmitter Array in 65nm CMOS Technology

NASA Technical Reports Server (NTRS)

Tang, Adrian; Virbila, Gabriel; Hsiao, Frank; Wu, Hao; Murphy, David; Mehdi, Imran; Siegel, P. H.; Chang, M-C. Frank

2013-01-01

This paper presents a complete 2x2 phased array transmitter system operating at W-band (90-95 GHz) which employs a PLL reference time-shifting approach instead of using traditional mm-wave phase shifters. PLL reference shifting enables a phased array to be distributed over multiple chips without the need for coherent mm-wave signal distribution between chips. The proposed phased array transmitter system consumes 248 mW per array element when implemented in a 65 nm CMOS technology.

Understanding the cost bases of Space Shuttle pricing policies for commercial and foreign customers

NASA Technical Reports Server (NTRS)

Stone, Barbara A.

1984-01-01

The principles and underlying cost bases of the 1977 and 1982 Space Shuttle Reimbursement Policies are compared and contrasted. Out-of-pocket cost recovery has been chosen as the base of the price for the 1986-1988 time period. With this cost base, it is NASA's intent to recover the total cost of consumables and the launch and flight operations costs added by commercial and foreign customers over the 1986-1988 time period. Beyond 1988, NASA intends to return to its policy of full cost recovery.

Maintaining Balance: The Increasing Role of Energy Storage for Renewable Integration

DOE PAGES

Stenclik, Derek; Denholm, Paul; Chalamala, Babu

2017-10-17

For nearly a century, global power systems have focused on three key functions: to generate, transmit, and distribute electricity as a real-time commodity. Physics requires that electricity generation always be in real-time balance with load, despite variability in load on timescales ranging from sub-second disturbances to multi-year trends. With the increasing role of variable generation from wind and solar, retirements of fossil fuel-based generation, and a changing consumer demand profile, grid operators are using new methods to maintain this balance.

Charge Scheduling of an Energy Storage System under Time-of-Use Pricing and a Demand Charge

PubMed Central

Yoon, Yourim

2014-01-01

A real-coded genetic algorithm is used to schedule the charging of an energy storage system (ESS), operated in tandem with renewable power by an electricity consumer who is subject to time-of-use pricing and a demand charge. Simulations based on load and generation profiles of typical residential customers show that an ESS scheduled by our algorithm can reduce electricity costs by approximately 17%, compared to a system without an ESS and by 8% compared to a scheduling algorithm based on net power. PMID:25197720

Model-Based Verification and Validation of Spacecraft Avionics

NASA Technical Reports Server (NTRS)

Khan, Mohammed Omair

2012-01-01

Our simulation was able to mimic the results of 30 tests on the actual hardware. This shows that simulations have the potential to enable early design validation - well before actual hardware exists. Although simulations focused around data processing procedures at subsystem and device level, they can also be applied to system level analysis to simulate mission scenarios and consumable tracking (e.g. power, propellant, etc.). Simulation engine plug-in developments are continually improving the product, but handling time for time-sensitive operations (like those of the remote engineering unit and bus controller) can be cumbersome.

Energy consumption and energy-saving potential analysis of pollutant abatement systems in a 1000MW coal-fired power plant.

PubMed

Yang, Hang; Zhang, Yongxin; Zheng, Chenghang; Wu, Xuecheng; Chen, Linghong; Gao, Xiang; Fu, Joshua S

2018-05-10

The pollutant abatement systems are widely applied in the coal-fired power sector and the energy consumption was considered an important part of the auxiliary power. An energy consumption analysis and assessment model of pollutant abatement systems in a power unit was developed based on the dynamic parameters and technology. The energy consumption of pollutant abatement systems in a 1000 MW coal-fired power unit which meet the ultra-low emission limits and the factors of operating parameters including unit load and inlet concentration of pollutants on the operating power were analyzed. The results show that the total power consumption of the pollutant abatement systems accounted for 1.27% of the gross power generation during the monitoring period. The WFGD system consumed 67% of the rate while the SCR and ESP systems consumed 8.9% and 24.1%. The power consumption rate of pollutant abatement systems decreased with the increase of unit load and increased with the increase of the inlet concentration of pollutants. The operation adjustment was also an effective method to increase the energy efficiency. For example, the operation adjustment of slurry circulation pumps could promote the energy-saving operation of WFGD system. Implication Statement The application of pollutant abatement technologies increases the internal energy consumption of the power plant, which will lead to an increase of power generation costs. The real-time energy consumption of the different pollutant abatement systems in a typical power unit is analyzed based on the dynamic operating data. Further, the influence of different operating parameters on the operating power of the system and the possible energy-saving potential are analyzed.

10 CFR Appendix I to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Conventional Ranges, Conventional...

Code of Federal Regulations, 2011 CFR

2011-01-01

...) (density of mercury equals 13.595 grams per cubic centimeter). 1.9Thermocouple means a device consisting of... Cleaning Operations per Year T—Temperature t—Time V—Volume of Gas Consumed W—Weight of Test Block 2. Test.... 2.9.2Gas Measurements. 2.9.2.1Positive displacement meters. The gas meter to be used for measuring...

The Army’s Operational Energy Challenge

DTIC Science & Technology

2011-05-01

battery chargers . Solar Hybrid—a system capable of providing up to 10 kilowatts of power continuously while reducing gen- erator running time by 20...granted. Army vehicles consume unprecedented amounts of fuel for mobility and onboard power. Average fuel demand per soldier has increased from about 1... electric power. This depen- dence translates to a vulnerability as fuel and water com- pose the vast majority of resupply volume, which, in turn

Terrain Characterization for Trafficability

DTIC Science & Technology

1993-06-01

pensive and less time-consuming. Although carefully raphy, on vehicle operation. This report focuses on the controlled laboratory tests may be more...relating indentation to soil strength. on a portable test rig or on an off-road vehicle where it A series of controlled experiments to determine the is... Controls and setting values for hydraulic pressures and flow Figure 10. Wheel are test rig (after Wasterhund 1990). 7 Vertical Proximity L ock-Oit~u

The Selection and Placement Method of Materialized Views on Big Data Platform of Equipment Condition Assessment

NASA Astrophysics Data System (ADS)

Ma, Yan; Yao, Jinxia; Gu, Chao; Chen, Yufeng; Yang, Yi; Zou, Lida

2017-05-01

With the formation of electric big data environment, more and more big data analyses emerge. In the complicated data analysis on equipment condition assessment, there exist many join operations, which are time-consuming. In order to save time, the approach of materialized view is usually used. It places part of common and critical join results on external storage and avoids the frequent join operation. In the paper we propose the methods of selecting and placing materialized views to reduce the query time of electric transmission and transformation equipment, and make the profits of service providers maximal. In selection method we design a computation way for the value of non-leaf node based on MVPP structure chart. In placement method we use relevance weights to place the selected materialized views, which help reduce the network transmission time. Our experiments show that the proposed selection and placement methods have a high throughput and good optimization ability of query time for electric transmission and transformation equipment.

77 FR 63800 - Proposed Extension of Approval of Information Collection; Comment Request-Safety Standard for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-17

... CONSUMER PRODUCT SAFETY COMMISSION Proposed Extension of Approval of Information Collection; Comment Request--Safety Standard for Automatic Residential Garage Door Operators AGENCY: Consumer Product... 1995 (44 U.S.C. Chapter 35), the Consumer Product Safety Commission (CPSC) requested comments on a...

Coming to grips with consumerism. [Panel answers on utility operations and problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Utility companies, as regulated monopolies, are facing increasing questioning and challenges from consumers. Representatives of the Consumer Federation of America, The Department of Energy, and Edison Electric Institute discuss the kind of information that consumers want and how they can get satisfactory responses from utility companies. The movement, seen as a healthy way for citizens to understand how utilities operate and to learn how to communicate their concerns, is assuming more of a conciliatory than adversary nature. In a panel discussion, the participants outline the issues of communication, rate structure, public relations, utility decision making, and regulation.

Feedback-Based Projected-Gradient Method for Real-Time Optimization of Aggregations of Energy Resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dall-Anese, Emiliano; Bernstein, Andrey; Simonetto, Andrea

This paper develops an online optimization method to maximize operational objectives of distribution-level distributed energy resources (DERs), while adjusting the aggregate power generated (or consumed) in response to services requested by grid operators. The design of the online algorithm is based on a projected-gradient method, suitably modified to accommodate appropriate measurements from the distribution network and the DERs. By virtue of this approach, the resultant algorithm can cope with inaccuracies in the representation of the AC power flows, it avoids pervasive metering to gather the state of noncontrollable resources, and it naturally lends itself to a distributed implementation. Optimality claimsmore » are established in terms of tracking of the solution of a well-posed time-varying convex optimization problem.« less

A simple method to ensure proper screw position and plate size selection using the Morscher cervical spine locking plate. Technical note.

PubMed

Ball, P A; Benzel, E C; Baldwin, N G

1994-04-01

The use of bone plate instrumentation with screw fixation has proved to be a useful adjunctive measure in anterior cervical spine fusion surgery. Proper fitting, positioning, and attachment of this instrumentation have been shown to be frequently suboptimal if done without radiographic guidance. The most commonly used method of radiographic assistance for placement of this instrumentation is fluoroscopy. While this gives satisfactory technical results, it is expensive and time-consuming, and exposes the patient and the operating room personnel to ionizing radiation. The authors present a simple technique to ensure screw placement and plate fitting using Kirschner wires and a single lateral radiograph. This technique saves time, reduces exposure to radiation, and has led to satisfactory results in over 20 operative cases.

Feedback-Based Projected-Gradient Method For Real-Time Optimization of Aggregations of Energy Resources: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dall-Anese, Emiliano; Bernstein, Andrey; Simonetto, Andrea

This paper develops an online optimization method to maximize the operational objectives of distribution-level distributed energy resources (DERs) while adjusting the aggregate power generated (or consumed) in response to services requested by grid operators. The design of the online algorithm is based on a projected-gradient method, suitably modified to accommodate appropriate measurements from the distribution network and the DERs. By virtue of this approach, the resultant algorithm can cope with inaccuracies in the representation of the AC power, it avoids pervasive metering to gather the state of noncontrollable resources, and it naturally lends itself to a distributed implementation. Optimality claimsmore » are established in terms of tracking of the solution of a well-posed time-varying optimization problem.« less

A Coordinated Patient Transport System for ICU Patients Requiring Surgery: Impact on Operating Room Efficiency and ICU Workflow.

PubMed

Brown, Michael J; Kor, Daryl J; Curry, Timothy B; Marmor, Yariv; Rohleder, Thomas R

2015-01-01

Transfer of intensive care unit (ICU) patients to the operating room (OR) is a resource-intensive, time-consuming process that often results in patient throughput inefficiencies, deficiencies in information transfer, and suboptimal nurse to patient ratios. This study evaluates the implementation of a coordinated patient transport system (CPTS) designed to address these issues. Using data from 1,557 patient transfers covering the 2006-2010 period, interrupted time series and before and after designs were used to analyze the effect of implementing a CPTS at Mayo Clinic, Rochester. Using a segmented regression for the interrupted time series, on-time OR start time deviations were found to be significantly lower after the implementation of CPTS (p < .0001). The implementation resulted in a fourfold improvement in on-time OR starts (p < .01) while significantly reducing idle OR time (p < .01). A coordinated patient transfer process for moving patient from ICUs to ORs can significantly improve OR efficiency, reduce nonvalue added time, and ensure quality of care by preserving appropriate care provider to patient ratios.

Practical Study for the Properties of Hueckel Edge Detection Operator

NASA Astrophysics Data System (ADS)

Jabbar, Hameed M. Abdul; Hatem, Amal J.; Ameer, Inbethaq M. A. Abdul

2018-05-01

The first practical study for the Hueckel edge detection operator was presented in this research, where it is tested on standard step edge set images. A number of criteria were adopted to evaluate its practical performance, which is the accuracy in detecting the edges direction, the error in the edges location (dislocation), edges width, the calculated edge goodness criterion and the consumed execution time. These criteria were studied with the edge direction and the used disk radius of the Hueckel edge detection operator. Important notes were recorded for the performance of this operator depending on the direction of the edge and/or with the radius of the used disk. There is a variation in the performance of the operator in terms of precision in detecting of the edges direction and position. A discussion was presented for the all criteria adopted in the research.

Wastewater Biosolid Composting Optimization Based on UV-VNIR Spectroscopy Monitoring

PubMed Central

Temporal-Lara, Beatriz; Melendez-Pastor, Ignacio; Gómez, Ignacio; Navarro-Pedreño, Jose

2016-01-01

Conventional wastewater treatment generates large amounts of organic matter–rich sludge that requires adequate treatment to avoid public health and environmental problems. The mixture of wastewater sludge and some bulking agents produces a biosolid to be composted at adequate composting facilities. The composting process is chemically and microbiologically complex and requires an adequate aeration of the biosolid (e.g., with a turner machine) for proper maturation of the compost. Adequate (near) real-time monitoring of the compost maturity process is highly difficult and the operation of composting facilities is not as automatized as other industrial processes. Spectroscopic analysis of compost samples has been successfully employed for compost maturity assessment but the preparation of the solid compost samples is difficult and time-consuming. This manuscript presents a methodology based on a combination of a less time-consuming compost sample preparation and ultraviolet, visible and short-wave near-infrared spectroscopy. Spectroscopic measurements were performed with liquid compost extract instead of solid compost samples. Partial least square (PLS) models were developed to quantify chemical fractions commonly employed for compost maturity assessment. Effective regression models were obtained for total organic matter (residual predictive deviation—RPD = 2.68), humification ratio (RPD = 2.23), total exchangeable carbon (RPD = 2.07) and total organic carbon (RPD = 1.66) with a modular and cost-effective visible and near infrared (VNIR) spectroradiometer. This combination of a less time-consuming compost sample preparation with a versatile sensor system provides an easy-to-implement, efficient and cost-effective protocol for compost maturity assessment and near-real-time monitoring. PMID:27854280

Wastewater Biosolid Composting Optimization Based on UV-VNIR Spectroscopy Monitoring.

PubMed

Temporal-Lara, Beatriz; Melendez-Pastor, Ignacio; Gómez, Ignacio; Navarro-Pedreño, Jose

2016-11-15

Conventional wastewater treatment generates large amounts of organic matter-rich sludge that requires adequate treatment to avoid public health and environmental problems. The mixture of wastewater sludge and some bulking agents produces a biosolid to be composted at adequate composting facilities. The composting process is chemically and microbiologically complex and requires an adequate aeration of the biosolid (e.g., with a turner machine) for proper maturation of the compost. Adequate (near) real-time monitoring of the compost maturity process is highly difficult and the operation of composting facilities is not as automatized as other industrial processes. Spectroscopic analysis of compost samples has been successfully employed for compost maturity assessment but the preparation of the solid compost samples is difficult and time-consuming. This manuscript presents a methodology based on a combination of a less time-consuming compost sample preparation and ultraviolet, visible and short-wave near-infrared spectroscopy. Spectroscopic measurements were performed with liquid compost extract instead of solid compost samples. Partial least square (PLS) models were developed to quantify chemical fractions commonly employed for compost maturity assessment. Effective regression models were obtained for total organic matter (residual predictive deviation-RPD = 2.68), humification ratio (RPD = 2.23), total exchangeable carbon (RPD = 2.07) and total organic carbon (RPD = 1.66) with a modular and cost-effective visible and near infrared (VNIR) spectroradiometer. This combination of a less time-consuming compost sample preparation with a versatile sensor system provides an easy-to-implement, efficient and cost-effective protocol for compost maturity assessment and near-real-time monitoring.

Understanding facilities design parameters for a remanufacturing system

NASA Astrophysics Data System (ADS)

Topcu, Aysegul; Cullinane, Thomas

2005-11-01

Remanufacturing is rapidly becoming a very important element in the economies of the world. Products such as washing machines, clothes driers, automobile parts, cell phones and a wide range of consumer durable goods are being reclaimed and sent through processes that restore these products to levels of operating performance that are as good or better than their new product performance. The operations involved in the remanufacturing process add several new dimensions to the work that must be performed. Disassembly is an operation that rarely appears on the operations chart of a typical production facility. The inspection and test functions in remanufacturing most often involve several more tasks than those involved in the first time manufacturing cycle. A close evaluation of most any remanufacturing operation reveals several points in the process in which parts must be cleaned, tested and stored. Although several researchers have focused their work on optimizing the disassembly function and the inspection, test and store functions, very little research has been devoted to studying the impact of the facilities design on the effectiveness of the remanufacturing process. The purpose of this paper will be to delineate the differences between first time manufacturing operations and remanufacturing operations for durable goods and to identify the features of the facilities design that must be considered if the remanufacturing operations are to be effective.

47 CFR 22.353 - Blanketing interference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Operational and Technical Requirements Technical Requirements § 22.353 Blanketing interference. Licensees of... consumer antenna systems, or the use of high gain antennas or antenna booster amplifiers by consumers. (d...

47 CFR 22.353 - Blanketing interference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Operational and Technical Requirements Technical Requirements § 22.353 Blanketing interference. Licensees of... consumer antenna systems, or the use of high gain antennas or antenna booster amplifiers by consumers. (d...

47 CFR 22.353 - Blanketing interference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Operational and Technical Requirements Technical Requirements § 22.353 Blanketing interference. Licensees of... consumer antenna systems, or the use of high gain antennas or antenna booster amplifiers by consumers. (d...

47 CFR 22.353 - Blanketing interference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Operational and Technical Requirements Technical Requirements § 22.353 Blanketing interference. Licensees of... consumer antenna systems, or the use of high gain antennas or antenna booster amplifiers by consumers. (d...

Use of resources and postoperative outcome.

PubMed

Niskanen, M M; Takala, J A

2001-09-01

To characterise those surgical patients who consume one half of all hospital patient days, and to compare their outcome with that of low consumers. A retrospective cohort study. Tertiary referral centre, Finland. 13025 surgical patients who were admitted to a university hospital in Kuopio, Finland, during 1997. The length of stay below which half of all patient days fell was chosen as a cut-off value to divide patients into low and high consumers. Hospital and 12-month mortality and standardised mortality ratios (SMR: observed deaths/expected deaths based on the corresponding general population). The 2239 patients (17%) whose length of stay exceeded 9 days (high consumers) took up one half of all patient days. The pattern of resource use varied between operative specialities. At 12 months the SMRs showed excess mortality among high consumers (5.0, 95% confidence interval 4.4 to 5.7) compared with low consumers (2.1, 95% CI 1.9 to 2.3). Relating the length of stay to the proportion of resources consumed may provide a feasible tool for the recognition of different patterns of use of resources. SMRs may be more relevant measures of outcome than hospital mortality when assessing the efficacy of operative treatment.

The mental health consumer movement and peer providers in Israel.

PubMed

Moran, G S

2018-04-16

Self-help peer-support groups in Israel emerged in the 1980s and, over time, dynamically interacted and co-developed with the statutory mental health (MH) system. In this editorial, I outline historical milestones of how the evolution of the Israeli mental health system was influenced by the consumer movement. A brief depiction of the consumer movement history. At first, consumers operated outside of the mainstream MH system. Gradually, consumer groups and institutional personnel joined efforts towards community integration and enhancement of quality of life, pushing forward a person-centered recovery orientation. In turn, some administrators and key stakeholders in rehabilitation community services grew to value the impact of knowledge-by-experience in contemporary mental health care. In this context, over the past decade, peer roles were developed in the mental health system, including consumer-providers in community services and peer specialists in inpatient psychiatric hospitals. The insertion of peer roles into the mainstream MH system is far-reaching, including the placement of a peer-project coordinator within the ministry of health. I describe the unique contribution of peers, as experts-by-experience, to mainstream professional knowledge and practice. I also highlight the potential challenges involved when peer models of care are added to traditional medical models of care. The Israeli case demonstrates how the consumer movement can play an active role in MH systems and be acknowledged and recognised as a partner for changing policy, practice and reshaping formal institutions. In addition, they play a vital role in the development of peer-support services.

14 CFR 298.30 - Public disclosure of policy on consumer protection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Public disclosure of policy on consumer protection. 298.30 Section 298.30 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION... Limitations and Conditions on Exemptions and Operations § 298.30 Public disclosure of policy on consumer...

12 CFR 41.32 - Sharing medical information with affiliates.

Code of Federal Regulations, 2010 CFR

2010-01-01

... operating subsidiaries. (b) In general. The exclusions from the term “consumer report” in section 603(d)(2... the term “consumer report” in section 603(d)(2) of the Act to communicate the information in paragraph... individualized list or description based on the payment transactions of the consumer for medical products or...

The "Village" Model: A Consumer-Driven Approach for Aging in Place

ERIC Educational Resources Information Center

Scharlach, Andrew; Graham, Carrie; Lehning, Amanda

2012-01-01

Purpose of the Study: This study examines the characteristics of the "Village" model, an innovative consumer-driven approach that aims to promote aging in place through a combination of member supports, service referrals, and consumer engagement. Design and Methods: Thirty of 42 fully operational Villages completed 2 surveys. One survey examined…

Why measure patient satisfaction?

PubMed

Riskind, Patty; Fossey, Leslie; Brill, Kari

2011-01-01

A practice that consistently and continuously measures patient perceptions will be more efficient and effective in its daily operations. With pay-for-performance requirements on the horizon and consumer rating sites already publicizing impressions from physician encounters, a practice needs to know how it is performing through the eyes of the patients. Azalea Orthopedics has used patient feedback to coach its physicians on better patient communication. The Orthopaedic Institute has used patient satisfaction results to reduce wait times and measure the return on investment from its marketing efforts. Patient survey results that are put to work can enhance the efficiency and effectiveness of practice operations as well as position the practice for increased profitability.

Radical behaviorist interpretation: Generating and evaluating an account of consumer behavior.

PubMed

Foxall, G R

1998-01-01

This article considers an approach to the radical behaviorist interpretation of complex human social behavior. The chosen context is consumer psychology, a field currently dominated by cognitive models of purchase and consumption. The nature of operant interpretation is considered, and several levels of operant analysis of complex economic behavior in affluent marketing-oriented economies are developed. Empirical evidence for the interpretation is considered, and a case is made for the qualified use of the hypothetico-deductive method in the appraisal of operant interpretations of complex behaviors.

Radical behaviorist interpretation: Generating and evaluating an account of consumer behavior

PubMed Central

Foxall, Gordon R.

1998-01-01

This article considers an approach to the radical behaviorist interpretation of complex human social behavior. The chosen context is consumer psychology, a field currently dominated by cognitive models of purchase and consumption. The nature of operant interpretation is considered, and several levels of operant analysis of complex economic behavior in affluent marketing-oriented economies are developed. Empirical evidence for the interpretation is considered, and a case is made for the qualified use of the hypothetico-deductive method in the appraisal of operant interpretations of complex behaviors. PMID:22478315

Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine Program: Background and Issues for Congress

DTIC Science & Technology

2015-12-17

requirement. Given the time needed for at-sea training operations, restocking SSBNs with food and other consumables, performing maintenance and repair...affect U.S. military capabilities and funding requirements, and the U.S. shipbuilding industrial base. This report focuses on the Ohio replacement...strategic nuclear arms reduction treaty that included 14 Ohio-class SSBNs, all armed with D- 5s . This recommendation prompted interest in the idea of

Method to Select Technical Terms for Glossaries in Support of Joint Task Force Operations

DTIC Science & Technology

2012-01-01

have been prohibitively time-consuming. Instead, we identified two publicly available terminology extractor tools: TerMine (NaCTEM, 2011) and Alchemy ...and that from the latter, by high recall. The Alchemy approach contrasts with that used in TerMine in that Alchemy will process the text with...information categories, such as person, location, and organization, in addition to returning topic keywords. Output from both TerMine and Alchemy

Optimal Multi-scale Demand-side Management for Continuous Power-Intensive Processes

NASA Astrophysics Data System (ADS)

Mitra, Sumit

With the advent of deregulation in electricity markets and an increasing share of intermittent power generation sources, the profitability of industrial consumers that operate power-intensive processes has become directly linked to the variability in energy prices. Thus, for industrial consumers that are able to adjust to the fluctuations, time-sensitive electricity prices (as part of so-called Demand-Side Management (DSM) in the smart grid) offer potential economical incentives. In this thesis, we introduce optimization models and decomposition strategies for the multi-scale Demand-Side Management of continuous power-intensive processes. On an operational level, we derive a mode formulation for scheduling under time-sensitive electricity prices. The formulation is applied to air separation plants and cement plants to minimize the operating cost. We also describe how a mode formulation can be used for industrial combined heat and power plants that are co-located at integrated chemical sites to increase operating profit by adjusting their steam and electricity production according to their inherent flexibility. Furthermore, a robust optimization formulation is developed to address the uncertainty in electricity prices by accounting for correlations and multiple ranges in the realization of the random variables. On a strategic level, we introduce a multi-scale model that provides an understanding of the value of flexibility of the current plant configuration and the value of additional flexibility in terms of retrofits for Demand-Side Management under product demand uncertainty. The integration of multiple time scales leads to large-scale two-stage stochastic programming problems, for which we need to apply decomposition strategies in order to obtain a good solution within a reasonable amount of time. Hence, we describe two decomposition schemes that can be applied to solve two-stage stochastic programming problems: First, a hybrid bi-level decomposition scheme with novel Lagrangean-type and subset-type cuts to strengthen the relaxation. Second, an enhanced cross-decomposition scheme that integrates Benders decomposition and Lagrangean decomposition on a scenario basis. To demonstrate the effectiveness of our developed methodology, we provide several industrial case studies throughout the thesis.

Functional and taxonomic dynamics of an electricity-consuming methane-producing microbial community.

PubMed

Bretschger, Orianna; Carpenter, Kayla; Phan, Tony; Suzuki, Shino; Ishii, Shun'ichi; Grossi-Soyster, Elysse; Flynn, Michael; Hogan, John

2015-11-01

The functional and taxonomic microbial dynamics of duplicate electricity-consuming methanogenic communities were observed over a 6 months period to characterize the reproducibility, stability and recovery of electromethanogenic consortia. The highest rate of methanogenesis was 0.72 mg-CH4/L/day, which occurred during the third month of enrichment when multiple methanogenic phylotypes and associated Desulfovibrionaceae phylotypes were present in the electrode-associated microbial community. Results also suggest that electromethanogenic microbial communities are very sensitive to electron donor-limiting open-circuit conditions. A 45 min exposure to open-circuit conditions induced an 87% drop in volumetric methane production rates. Methanogenic performance recovered after 4 months to a maximum value of 0.30 mg-CH4/L/day under set potential operation (-700 mV vs Ag/AgCl); however, current consumption and biomass production was variable over time. Long-term functional and taxonomic analyses from experimental replicates provide new knowledge toward understanding how to enrich electromethanogenic communities and operate bioelectrochemical systems for stable and reproducible performance. Copyright © 2015 Elsevier Ltd. All rights reserved.

Low-Cost Control System Built Upon Consumer-Based Electronics For Supervisory Control Of A Gas-Operated Heat Pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wetherington Jr, G Randall; Vineyard, Edward Allan; Mahderekal, Isaac

A preliminary evaluation of the performance of a consumer-based control system was conducted by the Oak Ridge National Laboratory (ORNL) and Southwest Gas as part of a cooperative research and development agreement (CRADA) authorized by the Department of Energy (DOE) (Mahderekal et al. (2013). The goal of the research was to evaluate the low-cost approach as a solution for implementing a supervisory control system for a residential gas-operated heat pump. The design incorporated two consumer-based micro-controllers; the Arduino Mega-2650 and the BeagleBone (white). Ten five-ton heat pump systems were designed, fabricated, and operationally tested in the Las Vega NV region.more » A robust data set was produced that allowed detailed assessment of the reliability and the operational perfromance of the newly developed control system. Experiences gained from the test provided important points of improvement for subsequent evolution of the heat pump technology.« less

Small helicopter could find niche in remote heavy lift operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-21

A new helicopter specifically designed for external vertical lift operations, such as moving transportable rig components or seismic equipment in remote locations, operates more efficiently than most other medium or heavy-lift helicopters, according to manufacturer Kaman Aerospace. The single-pilot helicopter was designed as an aerial truck for efficient lifting of heavy loads but with the operating costs of a light-lift craft. The K-Max helicopter can lift more pounds of cargo per gallon of fuel consumed than other similar helicopters, according to Kaman. For example, to transport a 5,000-lb load at an elevation of 8,000 ft, the K-Max helicopter consumes 85more » gal of fuel/hr. Under the same load conditions, the next most efficient commercially available helicopter consumes 160 gal of fuel/hr and requires two pilots. The 4,500-lb helicopter can lift 5,000 lb to an altitude of 8,000 ft or about 6,000 lb at low altitudes.« less

GASP- General Aviation Synthesis Program. Volume 7: Economics

NASA Technical Reports Server (NTRS)

1978-01-01

The economic analysis includes: manufacturing costs; labor costs; parts costs; operating costs; markups and consumer price. A user's manual for a computer program to calculate the final consumer price is included.

Evaluation of Operating Time and Patient Perception Using Conventional Impression Taking and Intraoral Scanning for Crown Manufacture: A Split-mouth, Randomized Clinical Study.

PubMed

Haddadi, Yasser; Bahrami, Golnosh; Isidor, Flemming

To compare operating time and patient perception of conventional impression (CI) taking and intraoral scanning (IOS) for manufacture of a tooth-supported crown. A total of 19 patients needing indirect full-coverage restorations fitting the requirements for a split-mouth design were recruited. Each patient received two lithium disilicate crowns, one manufactured from CI taking and one from IOS. Both teeth were prepared following the manufacturers' recommendations. For both impression techniques, two retraction cords soaked in 15% ferric sulphate were used for tissue management. CIs were taken in a full-arch metallic tray using one-step, two-viscosity technique with polyvinyl siloxane silicone. The operating time for each step of the two impression methods was registered. Patient perception associated with each method was scored using a 100-mm visual analog scale (VAS), with 100 indicating maximum discomfort. Median total operating time for CI taking was 15:47 minutes (interquartile range [IQR] 15:18 to 17:30), and for IOS was 5:05 minutes (IQR 4:35 to 5:23). The median VAS score for patient perception was 73 (IQR 16 to 89) for CI taking and 6 (IQR 2 to 9) for IOS. The differences between the two groups were statistically significant (P < .05) for both parameters. IOS was less time consuming than CI taking, and patient perception was in favor of IOS.

Demand side management in recycling and electricity retail pricing

NASA Astrophysics Data System (ADS)

Kazan, Osman

This dissertation addresses several problems from the recycling industry and electricity retail market. The first paper addresses a real-life scheduling problem faced by a national industrial recycling company. Based on their practices, a scheduling problem is defined, modeled, analyzed, and a solution is approximated efficiently. The recommended application is tested on the real-life data and randomly generated data. The scheduling improvements and the financial benefits are presented. The second problem is from electricity retail market. There are well-known patterns in daily usage in hours. These patterns change in shape and magnitude by seasons and days of the week. Generation costs are multiple times higher during the peak hours of the day. Yet most consumers purchase electricity at flat rates. This work explores analytic pricing tools to reduce peak load electricity demand for retailers. For that purpose, a nonlinear model that determines optimal hourly prices is established based on two major components: unit generation costs and consumers' utility. Both are analyzed and estimated empirically in the third paper. A pricing model is introduced to maximize the electric retailer's profit. As a result, a closed-form expression for the optimal price vector is obtained. Possible scenarios are evaluated for consumers' utility distribution. For the general case, we provide a numerical solution methodology to obtain the optimal pricing scheme. The models recommended are tested under various scenarios that consider consumer segmentation and multiple pricing policies. The recommended model reduces the peak load significantly in most cases. Several utility companies offer hourly pricing to their customers. They determine prices using historical data of unit electricity cost over time. In this dissertation we develop a nonlinear model that determines optimal hourly prices with parameter estimation. The last paper includes a regression analysis of the unit generation cost function obtained from Independent Service Operators. A consumer experiment is established to replicate the peak load behavior. As a result, consumers' utility function is estimated and optimal retail electricity prices are computed.

76 FR 5774 - Planning and Establishment of Consumer Operated and Oriented Plan Program; Request for Comments...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-02

...This document is a request for comments regarding the provisions of section 1322 of the Patient Protection and Affordable Care Act (the Affordable Care Act), enacted on March 23, 2010, which requires the Secretary to establish the Consumer Operated and Oriented Plan program. The Secretary of Health and Human Services invites public comments in advance of future rulemaking and grant and loan solicitations.

Problems of standardizing and technical regulation in the electric power industry

NASA Astrophysics Data System (ADS)

Grabchak, E. P.

2016-12-01

A mandatory condition to ensure normal operation of a power system and efficiency in the sector is standardization and legal regulation of technological activities of electric power engineering entities and consumers. Compared to the times of USSR, the present-time technical guidance documents are not mandatory to follow in most cases, being of an advisory nature due to the lack of new ones. During the last five years, the industry has been showing a deterioration of the situation in terms of ensuring reliability and engineering controllability as a result of the dominant impact of short-term market stimuli and the differences in basic technological policies. In absence of clear requirements regarding the engineering aspects of such activities, production operation does not contribute to the preserving of technical integrity of the Russian power system, which leads to the loss of performance capability and controllability and causes disturbances in the power supply to consumers. The result of this problem is a high rate of accident incidence. The dynamics of accidents by the type of equipment is given, indicating a persisting trend of growth in the number of accidents, which are of a systematic nature. Several problematic aspects of engineering activities of electric power engineering entities, requiring standardization and legal regulation are pointed out: in the domestic power system, a large number of power electrotechnical and generating equipment operate along with systems of regulation, which do not comply with the principles and technical rules representing a framework where the Energy System of Russia is built and functioning

Consumables data base workbook: Formulation of consumables management models

NASA Technical Reports Server (NTRS)

Zamora, M. A.

1977-01-01

Activity consumables data specifications and data applications are presented. The data are structured in a series of "Consumable Data Worksheets" for each activity that includes a profile of its operations and the rate of each consumable required to support the given activity. The data worksheets provide for the uniform specification of consumables data, allows for the ready identification of the consumables affected by a given activity, and facilitates the updating process. An activity is defined and the data that must be included in the data worksheets are specified. An example of its use and application is given, i.e. consumables data requirements for the performance of the EVA. The consumables data for the activities currently identified for the shuttle spacecraft are included. The consumables data sources are identified and information to facilitate the maintenance process is detailed.

Very low cost real time histogram-based contrast enhancer utilizing fixed-point DSP processing

NASA Astrophysics Data System (ADS)

McCaffrey, Nathaniel J.; Pantuso, Francis P.

1998-03-01

A real time contrast enhancement system utilizing histogram- based algorithms has been developed to operate on standard composite video signals. This low-cost DSP based system is designed with fixed-point algorithms and an off-chip look up table (LUT) to reduce the cost considerably over other contemporary approaches. This paper describes several real- time contrast enhancing systems advanced at the Sarnoff Corporation for high-speed visible and infrared cameras. The fixed-point enhancer was derived from these high performance cameras. The enhancer digitizes analog video and spatially subsamples the stream to qualify the scene's luminance. Simultaneously, the video is streamed through a LUT that has been programmed with the previous calculation. Reducing division operations by subsampling reduces calculation- cycles and also allows the processor to be used with cameras of nominal resolutions. All values are written to the LUT during blanking so no frames are lost. The enhancer measures 13 cm X 6.4 cm X 3.2 cm, operates off 9 VAC and consumes 12 W. This processor is small and inexpensive enough to be mounted with field deployed security cameras and can be used for surveillance, video forensics and real- time medical imaging.

78 FR 13857 - Foreign-Trade Zone 93-Raleigh-Durham, NC; Authorization of Production Activity; Revlon Consumer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-01

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-77-2012] Foreign-Trade Zone 93--Raleigh-Durham, NC; Authorization of Production Activity; Revlon Consumer Products Corporation (Hair Coloring Products); Oxford, NC On October 10, 2012, Revlon Consumer Products Corporation, the operator of FTZ 93G, submitted a notification of proposed production...

Consumer satisfaction with telehealth advice-nursing.

PubMed

Chang, B L; Mayo, A; Omery, A

2001-01-01

An increase in interest in the establishment of telephone advice services has resulted in the proliferation of call centers. Despite their wide usage, research for the most part has not addressed the quality of care in relation to consumer satisfaction. This paper examines consumer outcomes of satisfaction, and follow-up with recommendations, within a framework of the nursing process and its associated components of assessment (including problem identification), care planning, intervention, and evaluation. The data for the study were obtained from seven after-hours call centers operating under the auspices of health maintenance organizations, preferred provider organizations, and private insurance companies. A sample of 157 non-redundant telephone calls from adults with medical-surgical problems were audiotaped with providers' and callers' consent. Sociodemographic information of the advice nurses, and chief complaints of the callers were obtained. The quality of nursing of the audiotaped calls was rated through an implicit review method by registered nurse raters using an advice nurse structured implicit review (AN-SIR) form developed for the study. Follow-up information was obtained through telephone calls to ascertain the consumers' perceptions of satisfaction, helpfulness, and follow-through with recommendations. Results indicated that consumers calling with a variety of general complaints contacted 32 nurses in advice nurse call centers. The quality of nursing process was found to be the best in the area of intervention. Evaluation was also well above the midpoint on a transformed scale of zero to 100. Assessment, although slightly above midpoint, was the lowest of the three components of the nursing process examined. Consumer satisfaction was high with 95.4 percent of the consumers rating the calls as completely or at least somewhat satisfied, and 93.2 percent, stating the advice was very or somewhat helpful. Exploratory regression analysis showed that the component of intervention was significantly related to consumer satisfaction. The present study pioneers the way to rate the quality of the advice nurses' interactions with consumers, and lays the groundwork for further investigations of health care provider behavior and consumer outcomes. Further studies are recommended to investigate predictors of consumer satisfaction, and cost-benefit in terms of consumer expenditures of time, funds, and energy.

Our experience with a new instrument for laparoscopic gallbladder extraction, the "Bergetrokar".

PubMed

Höferlin, A; Höhle, K D

1993-01-01

Laparoscopic cholecystectomy has become a standardized technique within the last years. However, the extraction of the stone-filled gallbladder often becomes a time-consuming and difficult part of the operation. We have developed a new instrument for quick and safe extraction of the stone-filled gallbladder. The instrument, called "Bergetrokar", is a trocar cannula with a trumpet valve and cone-shaped tip which can be spread. The application of this device is simple. After using the "Bergetrokar" in about 180 cases we have not observed any perforation of the gallbladder or loss of stones. Extraction times were reduced.

Thrust vectoring systems

NASA Technical Reports Server (NTRS)

King, H. J.; Schnelker, D.; Ward, J. W.; Dulgeroff, C.; Vahrenkamp, R.

1972-01-01

The design, fabrication, and testing of thrust vectorable ion optical systems capable of controlling the thrust direction from both 5- and 30-cm diameter ion thrusters is described. Both systems are capable of greater than 10 deg thrust deflection in any azimuthal direction. The 5-cm system is electrostatic and hence has a short response time and minimal power consumption. It has recently been tested for more than 7500 hours on an operational thruster. The 30-cm system is mechanical, has a response time of the order of 1 min, and consumes less than 0.3% of the total system input power at full deflection angle.

LASH Ship Pretest Results of the Joint Logistics-Over-the-Shore (LOTS) Test and Evaluation Program.

DTIC Science & Technology

1977-03-07

75-05. 9 0 wU C-7) z C) S.- C)C 40 10 GA’THEFRING CO~l BARGE LIFTING POINT I , I I II I I . . .. .. KI- V~~ PS4 and 5. LCM8 LIFT BEAM IS ENGAGED...design but which could not be delivered in time by the vendor. The attachment of the struts proved to be a time- consuming effort because of too close...actually used in the pretest, the general behavior and characteristics are similar.) C-4 APPENDIX D BREAKBULK CARGO THROUGHPUT OPERATIONS As an adjunct to

A comparison of optimal and noise-abatement trajectories of a tilt-rotor aircraft

NASA Technical Reports Server (NTRS)

Schmitz, F. H.; Stepniewski, W. Z.; Gibs, J.; Hinterkeuser, W. Z.

1972-01-01

The potential benefits of flight path control to optimize performance and/or reduce the noise of a tilt-rotor aircraft operating in the takeoff and landing phases of flight are investigated. A theoretical performance-acoustic model is developed and then mathematically flown to yield representative takeoff and landing profiles. Minimum-time and minimum-fuel trajectories are compared to proposed noise-abatement profiles to assess the reductions in annoyance possible through flight path control. Significant reductions are feasible if a nearly vertical-takeoff flight profile is flown near the landing site; however, the time expended and fuel consumed increase.

Study to design and develop remote manipulator system

NASA Technical Reports Server (NTRS)

Hill, J. W.; Sword, A. J.

1973-01-01

Human performance measurement techniques for remote manipulation tasks and remote sensing techniques for manipulators are described for common manipulation tasks, performance is monitored by means of an on-line computer capable of measuring the joint angles of both master and slave arms as a function of time. The computer programs allow measurements of the operator's strategy and physical quantities such as task time and power consumed. The results are printed out after a test run to compare different experimental conditions. For tracking tasks, we describe a method of displaying errors in three dimensions and measuring the end-effector position in three dimensions.

Tetraethylene glycol promoted two-step, one-pot rapid synthesis of indole-3-[1- 11C]acetic acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Sojeong; Qu, Wenchao; Alexoff, David L.

2014-12-12

An operationally friendly, two-step, one-pot process has been developed for the rapid synthesis of carbon-11 labeled indole-3-acetic acid ([ 11]IAA or [ 11]auxin). By replacing an aprotic polar solvent with tetraethylene glycol, nucleophilic [ 11]cyanation and alkaline hydrolysis reactions were performed consecutively in a single pot without a time-consuming intermediate purification step. The entire production time for this updated procedure is 55 min, which dramatically simplifies the entire synthesis and reduces the starting radioactivity required for a whole plant imaging study.

R AND D 100 EARLYBIRD AWARD ENTRY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dugan, J; Debbie Chapman, D

2007-01-30

The Smart Latch{trademark} is an electronically enhanced door lockset device for industrial and consumer applications, which uses existing neural network technology to analyze the sequence, timing, and acoustic signatures associated with lockset functions and provides immediate indication of failure to correctly lock and latch. It essentially ''listens'' to and learns the sequences and acoustic signatures associated with lockset function and latching. When triggered by specific door activity the Smart Latch{trademark} begins analyzing sequences, frequencies and other parameters. With a satisfactory outcome the device provides positive feedback (e.g. visual and/or audible) and returns to a ''sleep'' state awaiting the next activity.more » If any part of the normal door operation, including latching and length of time, are incorrect various alarm signals can be generated. With electronics and 5+ year battery integrated, the device is simple to install and transparent to the user. Because the device uses proven voice recognition algorithms, it could meet or exceed the performance of the human ear in detecting the unique and complex acoustic signature associated with a properly operating and secured door. Unlike existing technologies, such as limit switches, it is not easily spoofed or defeated and has a high level of immunity to interference. The Smart Latch{trademark} technology can be integrated into existing lockset and door hardware designs, including both low price consumer products and high end electronic/cipher locks. The concept and design are based on a simple security industry adage: ''It isn't locked if it isn't latched''. Even the most elaborate and robust security barriers are of little use if the locking and latching mechanisms are not properly functioning and engaged. Smart Latch{trademark} provides automatic verification of the first and most important step in facility security: Close and properly latch doors and barriers. It is a compelling product for households with children, elderly, or high traffic areas such as an office where a properly closed and latched door is essential for security and safety. In an age of ever increasing security concerns and limited human resources, Smart Latch{trademark} can be a significant addition to the $20 billion plus industrial and consumer lockset market. The Smart Latch{trademark} is unique because: (1) as an inexpensive, battery powered, stand-alone device or as integrated into any standard consumer lock set, the device uses neural network technology to analyze the acoustic signatures associated with normal door operation and generates an alert if a door is not latched correctly and within a set amount of time. (2) It is not easily spoofed or defeated. (3) Installation, setup, and use are simple.« less

Image based automatic water meter reader

NASA Astrophysics Data System (ADS)

Jawas, N.; Indrianto

2018-01-01

Water meter is used as a tool to calculate water consumption. This tool works by utilizing water flow and shows the calculation result with mechanical digit counter. Practically, in everyday use, an operator will manually check the digit counter periodically. The Operator makes logs of the number shows by water meter to know the water consumption. This manual operation is time consuming and prone to human error. Therefore, in this paper we propose an automatic water meter digit reader from digital image. The digits sequence is detected by utilizing contour information of the water meter front panel.. Then an OCR method is used to get the each digit character. The digit sequence detection is an important part of overall process. It determines the success of overall system. The result shows promising results especially in sequence detection.

On Fusing Recursive Traversals of K-d Trees

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajbhandari, Samyam; Kim, Jinsung; Krishnamoorthy, Sriram

Loop fusion is a key program transformation for data locality optimization that is implemented in production compilers. But optimizing compilers currently cannot exploit fusion opportunities across a set of recursive tree traversal computations with producer-consumer relationships. In this paper, we develop a compile-time approach to dependence characterization and program transformation to enable fusion across recursively specified traversals over k-ary trees. We present the FuseT source-to-source code transformation framework to automatically generate fused composite recursive operators from an input program containing a sequence of primitive recursive operators. We use our framework to implement fused operators for MADNESS, Multiresolution Adaptive Numerical Environmentmore » for Scientific Simulation. We show that locality optimization through fusion can offer more than an order of magnitude performance improvement.« less

Are there any advantages in using a distal aiming device for tibial nailing? Comparing the Centro Nailing System with the Unreamed Tibia Nail.

PubMed

Veen, Egbert J D; Ettema, Harmen B; Zuurmond, Rutger G; Mostert, Adriaan K

2011-10-01

The distal locking of an intramedullary tibial nail can be challenging and time consuming when performed freehand. This study was conducted to evaluate if a distal aiming device would reduce surgical time. A case-controlled study was performed between 2007 and 2009 with 30 patients receiving a reamed tibial nail (Centronail) with the use of a distal aiming device and 30 patients who were treated with an Unreamed Tibia Nail (UTN), with freehand distal locking, in the same period. The primary outcome in this study was operative time. Secondary outcomes were the need for fluoroscopy, time to consolidation and complications. Operation time was longer in the Centronail group compared with the UTN group (126 min vs. 96 min, p=0.000). Use of fluoroscopy for distal locking was needed in half of the cases (n=16) using a distal aiming device. No differences were found regarding time to consolidation, time to removal of the nail and complications. The use of an aiming device for distal locking of a tibia nail lengthens operation time rather than reducing it. Fluoroscopy was still needed in about half of the cases. No difference was seen in clinical outcomes. The use of a distal aiming device to lock a tibial nail appears to have no benefit. Copyright © 2011 Elsevier Ltd. All rights reserved.

Lunar Surface Operations with Dual Rovers

NASA Technical Reports Server (NTRS)

Horz, Friedrich; Lofgren, Gary E.; Eppler, Dean E.; Ming, Douglas

2010-01-01

Lunar Electric Rovers (LER) are currently being developed that are substantially more capable than the Apollo vehicle (LRN ,"). Unlike the LRV, the new LERs provide a pressurized cabin that serves as short-sleeve environment for the crew of two, including sleeping accommodations and other provisions that allow for long tern stays, possibly up to 60 days, on the hear surface, without the need to replenish consumables from some outside source, such as a lander or outpost. As a consequence, significantly larger regions may be explored in the future and traverse distances may be measured in a few hundred kilometers (1, 2). However, crew safety remains an overriding concern, and methods other than "walk back", the major operational constraint of all Apollo traverses, must be implemented to assure -at any time- the safe return of the crew to the lander or outpost. This then causes current Constellation plans to envision long-tern traverses to be conducted with 2 LERs exclusively, each carrying a crew of two: in case one rover fails, the other will rescue the stranded crew and return all 4 astronauts in a single LER to base camp. Recent Desert Research and Technology Studies (DRATS) analog field tests simulated a continuous 14 day traverse (3), covering some 135 km, and included a rescue operation that transferred the crew and diverse consumables from one LER to another these successful tests add substantial realism to the development of long-term, dual rover operations. The simultaneous utilization of 2 LERs is of course totally unlike Apollo and raises interesting issues regarding science productivity and mission operations, the thrust of this note.

Whole-Home Dehumidifiers: Field-Monitoring Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burke, Tom; Willem, Henry; Ni, Chun Chun

2014-09-23

Lawrence Berkeley National Laboratory (LBNL) initiated a WHD field-metering study to expand current knowledge of and obtain data on WHD operation and energy consumption in real-world applications. The field study collected real-time data on WHD energy consumption, along with information regarding housing characteristics, consumer behavior, and various outdoor conditions expected to affect WHD performance and efficiency. Although the metering study collected similar data regarding air conditioner operation, this report discusses only WHDs. The primary objectives of the LBNL field-metering study are to (1) expand knowledge of the configurations, energy consumption profiles, consumer patterns of use (e.g., relative humidity [RH] settings),more » and environmental parameters of whole-home dehumidification systems; and (2) develop distributions of hours of dehumidifier operation in four operating modes: off, standby, fan-only, and compressor (also called dehumidification mode). Profiling energy consumption entails documenting the power consumption, duration of power consumption in different modes, condensate generation, and properties of output air of an installed system under field conditions of varying inlet air temperature and RH, as well as system configuration. This profiling provides a more detailed and deeper understanding of WHD operation and its complexities. This report describes LBNL’s whole-home dehumidification field-metering study conducted at four homes in Wisconsin and Florida. The initial phase of the WHD field-metering study was conducted on one home in Madison, Wisconsin, from June to December of 2013. During a second phase, three Florida homes were metered from June to October of 2014. This report presents and examines data from the Wisconsin site and from the three Florida sites.« less

Longitudinal comparative evaluation of the equivalence of an integrated peer-support and clinical staffing model for residential mental health rehabilitation: a mixed methods protocol incorporating multiple stakeholder perspectives.

PubMed

Parker, Stephen; Dark, Frances; Newman, Ellie; Korman, Nicole; Meurk, Carla; Siskind, Dan; Harris, Meredith

2016-06-02

A novel staffing model integrating peer support workers and clinical staff within a unified team is being trialled at community based residential rehabilitation units in Australia. A mixed-methods protocol for the longitudinal evaluation of the outcomes, expectations and experiences of care by consumers and staff under this staffing model in two units will be compared to one unit operating a traditional clinical staffing. The study is unique with regards to the context, the longitudinal approach and consideration of multiple stakeholder perspectives. The longitudinal mixed methods design integrates a quantitative evaluation of the outcomes of care for consumers at three residential rehabilitation units with an applied qualitative research methodology. The quantitative component utilizes a prospective cohort design to explore whether equivalent outcomes are achieved through engagement at residential rehabilitation units operating integrated and clinical staffing models. Comparative data will be available from the time of admission, discharge and 12-month period post-discharge from the units. Additionally, retrospective data for the 12-month period prior to admission will be utilized to consider changes in functioning pre and post engagement with residential rehabilitation care. The primary outcome will be change in psychosocial functioning, assessed using the total score on the Health of the Nation Outcome Scales (HoNOS). Planned secondary outcomes will include changes in symptomatology, disability, recovery orientation, carer quality of life, emergency department presentations, psychiatric inpatient bed days, and psychological distress and wellbeing. Planned analyses will include: cohort description; hierarchical linear regression modelling of the predictors of change in HoNOS following CCU care; and descriptive comparisons of the costs associated with the two staffing models. The qualitative component utilizes a pragmatic approach to grounded theory, with collection of data from consumers and staff at multiple time points exploring their expectations, experiences and reflections on the care provided by these services. It is expected that the new knowledge gained through this study will guide the adaptation of these and similar services. For example, if differential outcomes are achieved for consumers under the integrated and clinical staffing models this may inform staffing guidelines.

Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine Program: Background and Issues for Congress

DTIC Science & Technology

2013-10-22

time needed for at-sea training operations, restocking SSBNs with food and other consumables, performing maintenance and repair work on the SSBNs, and...during that period will be encumbered by lengthy maintenance actions. The Navy in May 2013 estimated the procurement cost of the lead ship in the...funding requirements, and the U.S. shipbuilding industrial base. This report focuses on the Ohio replacement program as a Navy shipbuilding program

Advanced Airframe Structural Materials: A Primer and Cost Estimating Methodology

DTIC Science & Technology

1991-01-01

laying machines for larger, mildly con- toured parts such as wing and stabilizer skins. For such parts, automated tape laying machines can operate many...heat guns (90-130°F). However, thermoplastics require as much as 650°F for forming. Automated tape laying machines for these materials use warm...cycles to properly seat the plies onto the tool. This time-consuming process can sometimes be eliminated or reduced by the use of automated tape laying procedures

Military Caregivers: Cornerstones of Support for Our Nation’s Wounded, Ill, and Injured Veterans

DTIC Science & Technology

2013-01-01

States has been engaged in the longest continu- ous period of combat operations in our history, fought by just 1 percent of Americans —all of them...Quality of Health Information for Consumers on the World Wide Web: A Systematic Review,” Journal of American Medical Association, Vol. 287, No. 20...average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed

Defining the Roles, Responsibilities, and Functions for Data Science Within the Defense Intelligence Agency

DTIC Science & Technology

2016-01-01

of data science within DIA and ensure the activities assist and inform DIA’s decisionmakers, analysts , and operators. The research addressed two key...by an analyst or researcher . This type of identifi- cation can be time-consuming and potentially full of errors. GENIE learns from ana- 1 Interview... analysts . The protocol can be found in Appendix A. The protocol was intended to elicit information in five broad research areas. First, we asked a

Use of a Microprocessor to Implement an ADCCP Protocol (Federal Standard 1003).

DTIC Science & Technology

1980-07-01

results of other studies, to evaluate the operational and economic impact of incorporating various options in Federal Standard 1003. The effort...the LSI interface and the microprocessor; the LSI chip deposits bytes in its buffer as the producer, and the MPU reads this data as the consumer...on the interface between the MPU and the LSI protocol chip. This requires two main processes to be running at the same time--transmit and receive. The

Space Vehicle Powerdown Philosophies Derived from the Space Shuttle Program

NASA Technical Reports Server (NTRS)

Willsey, Mark; Bailey, Brad

2011-01-01

In spaceflight, electrical power is a vital but limited resource. Almost every spacecraft system, from avionics to life support systems, relies on electrical power. Since power can be limited by the generation system s performance, available consumables, solar array shading, or heat rejection capability, vehicle power management is a critical consideration in spacecraft design, mission planning, and real-time operations. The purpose of this paper is to capture the powerdown philosophies used during the Space Shuttle Program. This paper will discuss how electrical equipment is managed real-time to adjust the overall vehicle power level to ensure that systems and consumables will support changing mission objectives, as well as how electrical equipment is managed following system anomalies. We will focus on the power related impacts of anomalies in the generation systems, air and liquid cooling systems, and significant environmental events such as a fire, decrease in cabin pressure, or micrometeoroid debris strike. Additionally, considerations for executing powerdowns by crew action or by ground commands from Mission Control will be presented. General lessons learned from nearly 30 years of Space Shuttle powerdowns will be discussed, including an in depth case-study of STS-117. During this International Space Station (ISS) assembly mission, a failure of computers controlling the ISS guidance, navigation, and control system required that the Space Shuttle s maneuvering system be used to maintain attitude control. A powerdown was performed to save power generation consumables, thus extending the docked mission duration and allowing more time to resolve the issue.

Patient Protection and Affordable Care Act; HHS Notice of Benefit and Payment Parameters for 2018; Amendments to Special Enrollment Periods and the Consumer Operated and Oriented Plan Program. Final rule.

PubMed

2016-12-22

This final rule sets forth payment parameters and provisions related to the risk adjustment program; cost-sharing parameters and cost-sharing reductions; and user fees for Federally-facilitated Exchanges and State-based Exchanges on the Federal platform. It also provides additional guidance relating to standardized options; qualified health plans; consumer assistance tools; network adequacy; the Small Business Health Options Programs; stand-alone dental plans; fair health insurance premiums; guaranteed availability and guaranteed renewability; the medical loss ratio program; eligibility and enrollment; appeals; consumer-operated and oriented plans; special enrollment periods; and other related topics.

Scheduling job shop - A case study

NASA Astrophysics Data System (ADS)

Abas, M.; Abbas, A.; Khan, W. A.

2016-08-01

The scheduling in job shop is important for efficient utilization of machines in the manufacturing industry. There are number of algorithms available for scheduling of jobs which depend on machines tools, indirect consumables and jobs which are to be processed. In this paper a case study is presented for scheduling of jobs when parts are treated on available machines. Through time and motion study setup time and operation time are measured as total processing time for variety of products having different manufacturing processes. Based on due dates different level of priority are assigned to the jobs and the jobs are scheduled on the basis of priority. In view of the measured processing time, the times for processing of some new jobs are estimated and for efficient utilization of the machines available an algorithm is proposed and validated.

Consumers' choice of drinking water: Is it dependent upon perceived quality, convenience, price and attitude?

NASA Astrophysics Data System (ADS)

Wahid, Nabsiah Abdul; Cheng, Patrick Tan Foon; Abustan, Ismail; Nee, Goh Yen

2017-10-01

Tap water is one of the many sources of water that the public as consumers can choose for drinking. This study hypothesized that perceived quality, convenience, price and environmental attitude would determine consumers's choice of drinking water following the Attribution Theory as the underlying model. A survey was carried out on Malaysia's public at large. From 301 usable data, the PLS analysis revealed that only perceived quality, convenience and price attributed towards the public's choice of drinking water while attitude was not significant. The findings are beneficial for the water sector industry, particularly for drinking water operators, state governments, and alternative drinking water manufacturers like bottled water companies. The ability to identify factors for why consumers in the marketplace choose the source of their drinking water would enable the operators to plan and strategize tactics that can disseminate accurate knowledge about the product that can motivate marketability of drinking water in Malaysia.

Leadership and characteristics of nonprofit mental health peer-run organizations nationwide.

PubMed

Ostrow, Laysha; Hayes, Stephania L

2015-04-01

Mental health peer-run organizations are nonprofits providing venues for support and advocacy among people diagnosed as having mental disorders. It has been proposed that consumer involvement is essential to their operations. This study reported organizational characteristics of peer-run organizations nationwide and how these organizations differ by degree of consumer control. Data were from the 2012 National Survey of Peer-Run Organizations. The analyses described the characteristics of the organizations (N=380) on five domains of nonprofit research, comparing results for organizations grouped by degree of involvement by consumers in the board of directors. Peer-run organizations provided a range of supports and educational and advocacy activities and varied in their capacity and resources. Some variation was explained by the degree of consumer control. These organizations seemed to be operating consistently with evidence on peer-run models. The reach of peer-run organizations, and the need for in-depth research, continues to grow.

Functional requirements for onboard management of space shuttle consumables, volume 2.

NASA Technical Reports Server (NTRS)

Graf, P. J.; Herwig, H. A.; Neel, L. W.

1973-01-01

A study was conducted to develop the functional requirements for onboard management of space shuttle consumables. A specific consumables management concept for the space shuttle vehicle was developed and the functional requirements for the onboard portion of the concept were generated. Consumables management is the process of controlling or influencing the usage of expendable materials involved in vehicle subsystem operation. The subsystems considered in the study are: (1) propulsion, (2) power generation, and (3) environmental and life support.

47 CFR 27.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Operation of certificated signal boosters. 27.9... boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies... operate a signal booster. [78 FR 21564, Apr. 11, 2013] ...

47 CFR 27.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Operation of certificated signal boosters. 27.9... boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies... operate a signal booster. [78 FR 21564, Apr. 11, 2013] ...

Robotic and endoscopic transaxillary thyroidectomies may be cost prohibitive when compared to standard cervical thyroidectomy: a cost analysis.

PubMed

Cabot, Jennifer C; Lee, Cho Rok; Brunaud, Laurent; Kleiman, David A; Chung, Woong Youn; Fahey, Thomas J; Zarnegar, Rasa

2012-12-01

This study presents a cost analysis of the standard cervical, gasless transaxillary endoscopic, and gasless transaxillary robotic thyroidectomy approaches based on medical costs in the United States. A retrospective review of 140 patients who underwent standard cervical, transaxillary endoscopic, or transaxillary robotic thyroidectomy at 2 tertiary centers was conducted. The cost model included operating room charges, anesthesia fee, consumables cost, equipment depreciation, and maintenance cost. Sensitivity analyses assessed individual cost variables. The mean operative times for the standard cervical, transaxillary endoscopic, and transaxillary robotic approaches were 121 ± 18.9, 185 ± 26.0, and 166 ± 29.4 minutes, respectively. The total cost for the standard cervical, transaxillary endoscopic, and transaxillary robotic approaches were $9,028 ± $891, $12,505 ± $1,222, and $13,670 ± $1,384, respectively. Transaxillary approaches were significantly more expensive than the standard cervical technique (standard cervical/transaxillary endoscopic, P < .0001; standard cervical/transaxillary robotic, P < .0001; and transaxillary endoscopic/transaxillary robotic, P = .001). The transaxillary and standard cervical techniques became equivalent in cost when transaxillary endoscopic operative time decreased to 111 minutes and transaxillary robotic operative time decreased to 68 minutes. Increasing the case load did not resolve the cost difference. Transaxillary endoscopic and transaxillary robotic thyroidectomies are significantly more expensive than the standard cervical approach. Decreasing operative times reduces this cost difference. The greater expense may be prohibitive in countries with a flat reimbursement schedule. Copyright © 2012 Mosby, Inc. All rights reserved.

Immediate liposuction could shorten the time for endoscopic axillary lymphadenectomy in breast cancer patients.

PubMed

Shi, Fujun; Huang, Zonghai; Yu, Jinlong; Zhang, Pusheng; Deng, Jianwen; Zou, Linhan; Zhang, Cheng; Luo, Yunfeng

2017-01-31

Endoscopic axillary lymphadenectomy (EALND) was introduced to clinical work to reduce side effects of conventional axillary lymphadenectomy, while the lipolysis and liposuction of EALND made the process consume more time. The aim of the study was to determine whether immediate liposuction after tumescent solution injection to the axilla could shorten the total time of EALND. Fifty-nine patients were enrolled in the study, 30 of them received EALND with traditional liposuction method (TLM), and the rest 29 patients received EALND with immediate liposuction method (ILM). The operation time, cosmetic result, drainage amount, and hospitalization time of the two groups were compared. The median EALND operation time of TLM group and ILM group were 68 and 46 min, respectively, the difference was significant (P < 0.05); the median cosmetic results of the two groups were 6.6 and 6.4, respectively; the median drainage amount of the two groups were 366 and 385 ml, respectively; the hospitalization time of the two groups were 15 and 16 days, respectively. For the last three measures, no significant difference was confirmed (P > 0.05). Our work suggests immediate liposuction could shorten the endoscopic axillary lymphadenectomy process, and this method would not compromise the operation results. However, due to the limitations of the research, more work needs to be done to prove the availability and feasibility of immediate liposuction.

A sorting system with automated gates permits individual operant experiments with mice from a social home cage.

PubMed

Winter, York; Schaefers, Andrea T U

2011-03-30

Behavioral experiments based on operant procedures can be time-consuming for small amounts of data. While individual testing and handling of animals can influence attention, emotion, and behavior, and interfere with experimental outcome, many operant protocols require individual testing. We developed an RFID-technology- and transponder-based sorting system that allows removing the human factor for longer-term experiments. Identity detectors and automated gates route mice individually from their social home cage to an adjacent operant compartment with 24/7 operation. CD1-mice learnt quickly to individually pass through the sorting system. At no time did more than a single mouse enter the operant compartment. After 3 days of adjusting to the sorting system, groups of 4 mice completed about 50 experimental trials per day in the operant compartment without experimenter intervention. The automated sorting system eliminates handling, isolation, and disturbance of the animals, eliminates experimenter-induced variability, saves experimenter time, and is financially economical. It makes possible a new approach for high-throughput experimentation, and is a viable tool for increasing quality and efficiency of many behavioral and neurobiological investigations. It can connect a social home cage, through individual sorting automation, to diverse setups including classical operant chambers, mazes, or arenas with video-based behavior classification. Such highly automated systems will permit efficient high-throughput screening even for transgenic animals with only subtle neurological or psychiatric symptoms where elaborate or longer-term protocols are required for behavioral diagnosis. Copyright © 2011 Elsevier B.V. All rights reserved.

High-efficiency VCSEL arrays for illumination and sensing in consumer applications

NASA Astrophysics Data System (ADS)

Seurin, Jean-Francois; Zhou, Delai; Xu, Guoyang; Miglo, Alexander; Li, Daizong; Chen, Tong; Guo, Baiming; Ghosh, Chuni

2016-03-01

There has been increased interest in vertical-cavity surface-emitting lasers (VCSELs) for illumination and sensing in the consumer market, especially for 3D sensing ("gesture recognition") and 3D image capture. For these applications, the typical wavelength range of interest is 830~950nm and power levels vary from a few milli-Watts to several Watts. The devices are operated in short pulse mode (a few nano-seconds) with fast rise and fall times for time-of-flight applications (ToF), or in CW/quasi-CW for structured light applications. In VCSELs, the narrow spectrum and its low temperature dependence allows the use of narrower filters and therefore better signal-to-noise performance, especially for outdoor applications. In portable devices (mobile devices, wearable devices, laptops etc.) the size of the illumination module (VCSEL and optics) is a primary consideration. VCSELs offer a unique benefit compared to other laser sources in that they are "surface-mountable" and can be easily integrated along with other electronics components on a printed circuit board (PCB). A critical concern is the power-conversion efficiency (PCE) of the illumination source operating at high temperatures (>50 deg C). We report on various VCSEL based devices and diffuser-integrated modules with high efficiency at high temperatures. Over 40% PCE was achieved in broad temperature range of 0-70 °C for either low power single devices or high power VCSEL arrays, with sub- nano-second rise and fall time. These high power VCSEL arrays show excellent reliability, with extracted mean-time-to-failure (MTTF) of over 500 years at 60 °C ambient temperature and 8W peak output.

Triple Play over Satellite, Ka-Band Making the Difference

NASA Astrophysics Data System (ADS)

Benoit, Guillaume; Fenech, Hector; Pezzana, Stefano

Over the last years a number of operators have been deploying satellite-based consumer internet access services to reduce the digital divide and capture the market of households not covered by ADSL, cable or wireless broadband. These operators are proposing a step change improvement in the economics of consumer service, with lower terminal costs, broadband access with monthly fees comparable to ADSL and an integrated technology simplifying the process of terminal installation, provisioning and management.

Improving striping operations through system optimization.

DOT National Transportation Integrated Search

2015-09-01

Striping operations generate a significant workload for Missouri Department of Transportation (MoDOT) maintenance : operations. The requirement for each striping crew to replenish its stock of paint and other consumable items from a bulk storage : fa...

Urban community perception towards intermittent water supply system.

PubMed

Joshi, M W; Talkhande, A V; Andey, S P; Kelkar, P S

2002-04-01

While evaluating intermittent and continuous water supply systems, consumers opinion survey was undertaken for critical appraisal of both modes of operation. With the help of a pre-designed set of questions relating to various aspects of water supply and the opinion of consumers regarding degree of service, a house to house survey was conducted in the study area of Ghaziabad and Jaipur. The consumer opinion survey clearly indicated a satisfactory degree of service wherever adequate quantity of water was made available irrespective of the mode of water supply. Number of complaints regarding quality of water supplied, timings of supply, low pressures and breakdowns in supply were reported during intermittent water supply. Every family stored water for drinking and other uses. Most of the families discard drinking water once the fresh water supply is resumed next day. Discarded drinking water is usually used in kitchen for washing and gardening. Storage for other purposes depends on economic status and availability of other sources like open dug well in the house. While most of the respondents had no complaints on water tariff, all of them were in favour of continuous water supply.

Towards viable drinking water services.

PubMed

Hukka, J J; Katko, T S

1997-01-01

This article offers a framework for developing viable drinking water services and institutional development in developing countries. The framework evolved from the authors' research and field experience in transition and developing economies. Viability is related to operative technology, appropriate organizations, and adequate cost recovery within the context of water resources, human and economic resources, sociocultural conditions, and other constraints. The ability of institutions to solve the problems of coordination and production depends upon player motivation, the complexity of the environment, and the ability of the players to control the environment. Third party enforcement of agreements are essential to reduce gains from opportunism, cheating, and shirking. Empirical research finds that per capita water production costs are 4 times higher in centralized systems and lowest in decentralized systems with coordination from a central party. Three-tiered systems of governments, regulators, and service providers are recommended. Management options must be consumer driven. The worst case scenario is consumer's reliance on vending and reselling with no alternative source of supply. Policies should have a strong focus on institutional reforms in the water sector, the development of a consumer driven water sector, facilitation of appropriate private-public partnerships, sound management of existing capital assets, a system for building viability into national strategies for the water sector, and financially self-sufficient and consumer responsible water supply organizations.

7 CFR 1215.52 - Exemption from assessment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Expenses and Assessments... popcorn annually, based on the previous year, shall be exempted from assessment. (b) Persons that operate...

7 CFR 1215.52 - Exemption from assessment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Expenses and Assessments... popcorn annually, based on the previous year, shall be exempted from assessment. (b) Persons that operate...

7 CFR 1215.52 - Exemption from assessment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Expenses and Assessments... popcorn annually, based on the previous year, shall be exempted from assessment. (b) Persons that operate...

7 CFR 1215.52 - Exemption from assessment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Expenses and Assessments... popcorn annually, based on the previous year, shall be exempted from assessment. (b) Persons that operate...

7 CFR 1215.52 - Exemption from assessment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Expenses and Assessments... popcorn annually, based on the previous year, shall be exempted from assessment. (b) Persons that operate...

7 CFR 1209.52 - Exemption from assessment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MUSHROOM PROMOTION, RESEARCH, AND CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Expenses... mushrooms annually; and (2) A producer who operates under an approved National Organic Program (NOP) (7 CFR...

7 CFR 1209.52 - Exemption from assessment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MUSHROOM PROMOTION, RESEARCH, AND CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Expenses... mushrooms annually; and (2) A producer who operates under an approved National Organic Program (NOP) (7 CFR...

7 CFR 1209.52 - Exemption from assessment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MUSHROOM PROMOTION, RESEARCH, AND CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Expenses... mushrooms annually; and (2) A producer who operates under an approved National Organic Program (NOP) (7 CFR...

7 CFR 1209.52 - Exemption from assessment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MUSHROOM PROMOTION, RESEARCH, AND CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Expenses... mushrooms annually; and (2) A producer who operates under an approved National Organic Program (NOP) (7 CFR...

7 CFR 1209.52 - Exemption from assessment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MUSHROOM PROMOTION, RESEARCH, AND CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Expenses... mushrooms annually; and (2) A producer who operates under an approved National Organic Program (NOP) (7 CFR...

The Wallsend Owenites

ERIC Educational Resources Information Center

Todd, Nigel

2013-01-01

The nineteenth-century British Co-operative Movement included a commitment to education. Although only a minority of consumer co-operative societies offered educational facilities for their members, there was a willingness to experiment among those Co-operators whose grasp of Co-operation extended ideologically beyond remaining content with…

Multi-period equilibrium/near-equilibrium in electricity markets based on locational marginal prices

NASA Astrophysics Data System (ADS)

Garcia Bertrand, Raquel

In this dissertation we propose an equilibrium procedure that coordinates the point of view of every market agent resulting in an equilibrium that simultaneously maximizes the independent objective of every market agent and satisfies network constraints. Therefore, the activities of the generating companies, consumers and an independent system operator are modeled: (1) The generating companies seek to maximize profits by specifying hourly step functions of productions and minimum selling prices, and bounds on productions. (2) The goals of the consumers are to maximize their economic utilities by specifying hourly step functions of demands and maximum buying prices, and bounds on demands. (3) The independent system operator then clears the market taking into account consistency conditions as well as capacity and line losses so as to achieve maximum social welfare. Then, we approach this equilibrium problem using complementarity theory in order to have the capability of imposing constraints on dual variables, i.e., on prices, such as minimum profit conditions for the generating units or maximum cost conditions for the consumers. In this way, given the form of the individual optimization problems, the Karush-Kuhn-Tucker conditions for the generating companies, the consumers and the independent system operator are both necessary and sufficient. The simultaneous solution to all these conditions constitutes a mixed linear complementarity problem. We include minimum profit constraints imposed by the units in the market equilibrium model. These constraints are added as additional constraints to the equivalent quadratic programming problem of the mixed linear complementarity problem previously described. For the sake of clarity, the proposed equilibrium or near-equilibrium is first developed for the particular case considering only one time period. Afterwards, we consider an equilibrium or near-equilibrium applied to a multi-period framework. This model embodies binary decisions, i.e., on/off status for the units, and therefore optimality conditions cannot be directly applied. To avoid limitations provoked by binary variables, while retaining the advantages of using optimality conditions, we define the multi-period market equilibrium using Benders decomposition, which allows computing binary variables through the master problem and continuous variables through the subproblem. Finally, we illustrate these market equilibrium concepts through several case studies.

10 CFR Appendix Y to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Battery Chargers

Code of Federal Regulations, 2011 CFR

2011-01-01

... power (i.e., watts) consumed as the time series integral of the power consumed over a 1-hour test period...) consumed as the time series integral of the power consumed over a 1-hour test period, divided by the period...-maintenance mode and standby mode over time periods defined in the test procedure. b. Active mode is the...

10 CFR Appendix Y to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Battery Chargers

Code of Federal Regulations, 2010 CFR

2010-01-01

... power (i.e., watts) consumed as the time series integral of the power consumed over a 1-hour test period...) consumed as the time series integral of the power consumed over a 1-hour test period, divided by the period...-maintenance mode and standby mode over time periods defined in the test procedure. b. Active mode is the...

A Meaty Project. A Learning Activity Capsule in Consumer Operations Survival Training. Teacher's Guide [and] Student Material.

ERIC Educational Resources Information Center

Williams, Virginia

The unit introduces junior high school students to the different kinds of ground beef available to consumers. Objectives are to identify sources of meat for ground beef and evaluate the different types to determine how each can best be used by the consumer. Activities include identifying types of meat from an illustrated worksheet, buying at least…

Development of a Time-Intensity Evaluation System for Consumers: Measuring Bitterness and Retronasal Aroma of Coffee Beverages in 106 Untrained Panelists.

PubMed

Gotow, Naomi; Moritani, Ami; Hayakawa, Yoshinobu; Akutagawa, Akihito; Hashimoto, Hiroshi; Kobayakawa, Tatsu

2015-06-01

In order to develop products that are acceptable to consumers, it is necessary to incorporate consumers' intentions into products' characteristics. Therefore, investigation of consumers' perceptions of the taste or smell of common beverages provides information that should be useful in predicting market responses. In this study, we sought to develop a time-intensity evaluation system for consumer panels. Using our system, we performed time-intensity evaluation of flavor attributes (bitterness and retronasal aroma) that consumers perceived after swallowing a coffee beverage. Additionally, we developed quantitative evaluation methods for determining whether consumer panelists can properly perform time-intensity evaluation. In every trial, we fitted an exponential function to measured intensity data for bitterness and retronasal aroma. The correlation coefficients between measured time-intensity data and the fitted exponential curves were greater than 0.8 in about 90% of trials, indicating that we had successfully developed a time-intensity system for use with consumer panelists, even after just a single training trial using a nontrained consumer. We classified participants into two groups based on their consumption of canned coffee beverages. Significant difference was observed in only AUC of sensory modality (bitterness compared with retronasal aroma) among conventional TI parameters using two-way ANOVA. However, three-way ANOVA including a time course revealed significant difference between bitterness and retronasal aroma in the high-consumption group. Moreover, the high-consumption group more easily discriminated between bitterness and retronasal aroma than the low-consumption group. This finding implied that manufacturers should select consumer panelists who are suitable for their concepts of new products. © 2015 Institute of Food Technologists®

Total Probability of Collision as a Metric for Finite Conjunction Assessment and Collision Risk Management

NASA Technical Reports Server (NTRS)

Frigm, Ryan C.; Hejduk, Matthew D.; Johnson, Lauren C.; Plakalovic, Dragan

2015-01-01

On-orbit collision risk is becoming an increasing mission risk to all operational satellites in Earth orbit. Managing this risk can be disruptive to mission and operations, present challenges for decision-makers, and is time-consuming for all parties involved. With the planned capability improvements to detecting and tracking smaller orbital debris and capacity improvements to routinely predict on-orbit conjunctions, this mission risk will continue to grow in terms of likelihood and effort. It is very real possibility that the future space environment will not allow collision risk management and mission operations to be conducted in the same manner as it is today. This paper presents the concept of a finite conjunction assessment-one where each discrete conjunction is not treated separately but, rather, as a continuous event that must be managed concurrently. The paper also introduces the Total Probability of Collision as an analogous metric for finite conjunction assessment operations and provides several options for its usage in a Concept of Operations.

Constrained Optimization of Average Arrival Time via a Probabilistic Approach to Transport Reliability

PubMed Central

Namazi-Rad, Mohammad-Reza; Dunbar, Michelle; Ghaderi, Hadi; Mokhtarian, Payam

2015-01-01

To achieve greater transit-time reduction and improvement in reliability of transport services, there is an increasing need to assist transport planners in understanding the value of punctuality; i.e. the potential improvements, not only to service quality and the consumer but also to the actual profitability of the service. In order for this to be achieved, it is important to understand the network-specific aspects that affect both the ability to decrease transit-time, and the associated cost-benefit of doing so. In this paper, we outline a framework for evaluating the effectiveness of proposed changes to average transit-time, so as to determine the optimal choice of average arrival time subject to desired punctuality levels whilst simultaneously minimizing operational costs. We model the service transit-time variability using a truncated probability density function, and simultaneously compare the trade-off between potential gains and increased service costs, for several commonly employed cost-benefit functions of general form. We formulate this problem as a constrained optimization problem to determine the optimal choice of average transit time, so as to increase the level of service punctuality, whilst simultaneously ensuring a minimum level of cost-benefit to the service operator. PMID:25992902

New procedure speeds cold start, protects turbine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallard, R.E.; Jordan, C.A.

1995-09-01

System dispatch from today`s power plants must consider availability of purchase power (buy and sell), fuel prices, and unit availability and efficiency. To gain the best combination of these factors, steam units must be capable of quick removal and return to service. However, unit startups are expensive, time consuming nd operationally demanding. For example, excessive thermal stresses can be catastrophic to a unit. With those factors in mind, Jacksonville Electric Authority (JEA) developed the ``valve open start`` procedure described here.

75 FR 1076 - Outer Continental Shelf Civil Penalties

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-08

...The Outer Continental Shelf Lands Act requires the MMS to review the maximum daily civil penalty assessment for violations of regulations governing oil and gas operations in the Outer Continental Shelf at least once every 3 years. This review ensures that the maximum penalty assessment reflects any increases in the Consumer Price Index as prepared by the Bureau of Labor Statistics, U.S. Department of Labor. After conducting the required review in August 2009, the MMS determined that no adjustment is necessary at this time.

47 CFR 24.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Operation of certificated signal boosters. 24.9... PERSONAL COMMUNICATIONS SERVICES General Information § 24.9 Operation of certificated signal boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies regulated...

47 CFR 24.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Operation of certificated signal boosters. 24.9... PERSONAL COMMUNICATIONS SERVICES General Information § 24.9 Operation of certificated signal boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies regulated...

Integrated software health management for aerospace guidance, navigation, and control systems: A probabilistic reasoning approach

NASA Astrophysics Data System (ADS)

Mbaya, Timmy

Embedded Aerospace Systems have to perform safety and mission critical operations in a real-time environment where timing and functional correctness are extremely important. Guidance, Navigation, and Control (GN&C) systems substantially rely on complex software interfacing with hardware in real-time; any faults in software or hardware, or their interaction could result in fatal consequences. Integrated Software Health Management (ISWHM) provides an approach for detection and diagnosis of software failures while the software is in operation. The ISWHM approach is based on probabilistic modeling of software and hardware sensors using a Bayesian network. To meet memory and timing constraints of real-time embedded execution, the Bayesian network is compiled into an Arithmetic Circuit, which is used for on-line monitoring. This type of system monitoring, using an ISWHM, provides automated reasoning capabilities that compute diagnoses in a timely manner when failures occur. This reasoning capability enables time-critical mitigating decisions and relieves the human agent from the time-consuming and arduous task of foraging through a multitude of isolated---and often contradictory---diagnosis data. For the purpose of demonstrating the relevance of ISWHM, modeling and reasoning is performed on a simple simulated aerospace system running on a real-time operating system emulator, the OSEK/Trampoline platform. Models for a small satellite and an F-16 fighter jet GN&C (Guidance, Navigation, and Control) system have been implemented. Analysis of the ISWHM is then performed by injecting faults and analyzing the ISWHM's diagnoses.

An improved fast acquisition phase frequency detector for high speed phase-locked loops

NASA Astrophysics Data System (ADS)

Zhang, Lei; Wang, Zongmin; Zhang, Tieliang; Peng, Xinmang

2018-04-01

Phase-locked loops (PLL) have been widely applied in many high-speed designs, such as microprocessors or communication systems. In this paper, an improved fast acquisition phase frequency detector for high speed phase-locked loops is proposed. An improved structure based on dynamic latch is used to eliminate the non-ideal effect such as dead zone and blind zone. And frequency dividers are utilized to vastly extend the phase difference detection range and enhance the operation frequency of the PLL. Proposed PFD has been implemented in 65nm CMOS technology, which occupies an area of 0.0016mm2 and consumes 1.5mW only. Simulation results demonstrate that maximum operation frequency can be up to 5GHz. In addition, the acquisition time of PLL using proposed PFD is 1.0us which is 2.6 times faster than that of the PLL using latch-based PFD without divider.

Rapid automated classification of anesthetic depth levels using GPU based parallelization of neural networks.

PubMed

Peker, Musa; Şen, Baha; Gürüler, Hüseyin

2015-02-01

The effect of anesthesia on the patient is referred to as depth of anesthesia. Rapid classification of appropriate depth level of anesthesia is a matter of great importance in surgical operations. Similarly, accelerating classification algorithms is important for the rapid solution of problems in the field of biomedical signal processing. However numerous, time-consuming mathematical operations are required when training and testing stages of the classification algorithms, especially in neural networks. In this study, to accelerate the process, parallel programming and computing platform (Nvidia CUDA) facilitates dramatic increases in computing performance by harnessing the power of the graphics processing unit (GPU) was utilized. The system was employed to detect anesthetic depth level on related electroencephalogram (EEG) data set. This dataset is rather complex and large. Moreover, the achieving more anesthetic levels with rapid response is critical in anesthesia. The proposed parallelization method yielded high accurate classification results in a faster time.

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2013 CFR

2013-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2014 CFR

2014-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2012 CFR

2012-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

Tunable reverse-biased graphene/silicon heterojunction Schottky diode sensor.

PubMed

Singh, Amol; Uddin, Ahsan; Sudarshan, Tangali; Koley, Goutam

2014-04-24

A new chemical sensor based on reverse-biased graphene/Si heterojunction diode has been developed that exhibits extremely high bias-dependent molecular detection sensitivity and low operating power. The device takes advantage of graphene's atomically thin nature, which enables molecular adsorption on its surface to directly alter graphene/Si interface barrier height, thus affecting the junction current exponentially when operated in reverse bias and resulting in ultrahigh sensitivity. By operating the device in reverse bias, the work function of graphene, and hence the barrier height at the graphene/Si heterointerface, can be controlled by the bias magnitude, leading to a wide tunability of the molecular detection sensitivity. Such sensitivity control is also possible by carefully selecting the graphene/Si heterojunction Schottky barrier height. Compared to a conventional graphene amperometric sensor fabricated on the same chip, the proposed sensor demonstrated 13 times higher sensitivity for NO₂ and 3 times higher for NH₃ in ambient conditions, while consuming ∼500 times less power for same magnitude of applied voltage bias. The sensing mechanism based on heterojunction Schottky barrier height change has been confirmed using capacitance-voltage measurements. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Agent-Based Framework for Personalized Service Provisioning in Converged IP Networks

NASA Astrophysics Data System (ADS)

Podobnik, Vedran; Matijasevic, Maja; Lovrek, Ignac; Skorin-Kapov, Lea; Desic, Sasa

In a global multi-service and multi-provider market, the Internet Service Providers will increasingly need to differentiate in the service quality they offer and base their operation on new, consumer-centric business models. In this paper, we propose an agent-based framework for the Business-to-Consumer (B2C) electronic market, comprising the Consumer Agents, Broker Agents and Content Agents, which enable Internet consumers to select a content provider in an automated manner. We also discuss how to dynamically allocate network resources to provide end-to-end Quality of Service (QoS) for a given consumer and content provider.

Comparative assessment of the environmental sustainability of existing and emerging perchlorate treatment technologies for drinking water.

PubMed

Choe, Jong Kwon; Mehnert, Michelle H; Guest, Jeremy S; Strathmann, Timothy J; Werth, Charles J

2013-05-07

Environmental impacts of conventional and emerging perchlorate drinking water treatment technologies were assessed using life cycle assessment (LCA). Comparison of two ion exchange (IX) technologies (i.e., nonselective IX with periodic regeneration using brines and perchlorate-selective IX without regeneration) at an existing plant shows that brine is the dominant contributor for nonselective IX, which shows higher impact than perchlorate-selective IX. Resource consumption during the operational phase comprises >80% of the total impacts. Having identified consumables as the driving force behind environmental impacts, the relative environmental sustainability of IX, biological treatment, and catalytic reduction technologies are compared more generally using consumable inputs. The analysis indicates that the environmental impacts of heterotrophic biological treatment are 2-5 times more sensitive to influent conditions (i.e., nitrate/oxygen concentration) and are 3-14 times higher compared to IX. However, autotrophic biological treatment is most environmentally beneficial among all. Catalytic treatment using carbon-supported Re-Pd has a higher (ca. 4600 times) impact than others, but is within 0.9-30 times the impact of IX with a newly developed ligand-complexed Re-Pd catalyst formulation. This suggests catalytic reduction can be competitive with increased activity. Our assessment shows that while IX is an environmentally competitive, emerging technologies also show great promise from an environmental sustainability perspective.

12 CFR Supplement I to Part 1005 - Official Interpretations

Code of Federal Regulations, 2013 CFR

2013-01-01

... used to capture the Magnetic Ink Character Recognition (MICR) encoding to initiate a one-time automated clearinghouse (ACH) debit. For example, if a consumer authorizes a one-time ACH debit from the consumer's... involved at the time of the transaction, if the consumer's asset account is subsequently debited for the...

12 CFR Supplement I to Part 1005 - Official Interpretations

Code of Federal Regulations, 2012 CFR

2012-01-01

... used to capture the Magnetic Ink Character Recognition (MICR) encoding to initiate a one-time automated clearinghouse (ACH) debit. For example, if a consumer authorizes a one-time ACH debit from the consumer's... involved at the time of the transaction, if the consumer's asset account is subsequently debited for the...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2014 CFR

2014-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

12 CFR 1005.3 - Coverage.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-time electronic fund transfer from a consumer's account. The consumer must authorize the transfer. (ii... one-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR... transfer. A consumer authorizes a one-time electronic fund transfer from his or her account to pay the fee...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2011 CFR

2011-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2013 CFR

2013-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

77 FR 76005 - Submission for OMB Review; Comment Request-Requirements for Electrically Operated Toys and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... Request--Requirements for Electrically Operated Toys and Children's Articles AGENCY: Consumer Product... articles. DATES: Written comments on this request for extension of approval of information collection... the Requirements for Electrically Operated Toys or Other Electrically Operated Articles Intended for...

47 CFR 22.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Operation of certificated signal boosters. 22.9... PUBLIC MOBILE SERVICES Scope and Authority § 22.9 Operation of certificated signal boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies regulated under...

47 CFR 22.9 - Operation of certificated signal boosters.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Operation of certificated signal boosters. 22.9... PUBLIC MOBILE SERVICES Scope and Authority § 22.9 Operation of certificated signal boosters. Individuals and non-individuals may operate certificated Consumer Signal Boosters on frequencies regulated under...

45 CFR 98.33 - Consumer education.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Program Operations (Child Care Services)-Parental Rights and Responsibilities § 98.33 Consumer education... uses to determine if the parent has a demonstrated inability to obtain needed child care; (2) The...

45 CFR 98.33 - Consumer education.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Welfare Department of Health and Human Services GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Program Operations (Child Care Services)-Parental Rights and Responsibilities § 98.33 Consumer education... uses to determine if the parent has a demonstrated inability to obtain needed child care; (2) The...

45 CFR 98.33 - Consumer education.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Program Operations (Child Care Services)-Parental Rights and Responsibilities § 98.33 Consumer education... uses to determine if the parent has a demonstrated inability to obtain needed child care; (2) The...

A novel composite adaptive flap controller design by a high-efficient modified differential evolution identification approach.

PubMed

Li, Nailu; Mu, Anle; Yang, Xiyun; Magar, Kaman T; Liu, Chao

2018-05-01

The optimal tuning of adaptive flap controller can improve adaptive flap control performance on uncertain operating environments, but the optimization process is usually time-consuming and it is difficult to design proper optimal tuning strategy for the flap control system (FCS). To solve this problem, a novel adaptive flap controller is designed based on a high-efficient differential evolution (DE) identification technique and composite adaptive internal model control (CAIMC) strategy. The optimal tuning can be easily obtained by DE identified inverse of the FCS via CAIMC structure. To achieve fast tuning, a high-efficient modified adaptive DE algorithm is proposed with new mutant operator and varying range adaptive mechanism for the FCS identification. A tradeoff between optimized adaptive flap control and low computation cost is successfully achieved by proposed controller. Simulation results show the robustness of proposed method and its superiority to conventional adaptive IMC (AIMC) flap controller and the CAIMC flap controllers using other DE algorithms on various uncertain operating conditions. The high computation efficiency of proposed controller is also verified based on the computation time on those operating cases. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Effect of hydraulic retention time (HRT) on the anaerobic co-digestion of agro-industrial wastes in a two-stage CSTR system.

PubMed

Dareioti, Margarita Andreas; Kornaros, Michael

2014-09-01

A two-stage anaerobic digestion system consisting of two continuously stirred tank reactors (CSTRs) operating at mesophilic conditions (37°C) were used to investigate the effect of hydraulic retention time (HRT) on hydrogen and methane production. The acidogenic reactor was fed with a mixture consisting of olive mill wastewater, cheese whey and liquid cow manure (in a ratio 55:40:5, v/v/v) and operated at five different HRTs (5, 3, 2, 1 and 0.75 d) aiming to evaluate hydrogen productivity and operational stability. The highest system efficiency was achieved at HRT 0.75 d with a maximum hydrogen production rate of 1.72 L/LRd and hydrogen yield of 0.54 mol H2/mol carbohydrates consumed. The methanogenic reactor was operated at HRTs 20 and 25 d with better stability observed at HRT 25 d, whereas accumulation of volatile fatty acids took place at HRT 20 d. The methane production rate at the steady state of HRT 25 d reached 0.33 L CH4/LRd. Copyright © 2014 Elsevier Ltd. All rights reserved.

Taking a traditional web site to patient portal technology.

PubMed

Labow, Kimberly

2010-01-01

In this era of consumer-driven healthcare, consumers (your current and potential patients) seek healthcare information on the Internet. If your practice doesn't have a Web site, or has one that's static and uninformative, you won't be found, and the patient will move on to the next practice Web site. Why? Because only the most graphically appealing, informative, and patient-centered Web sites will drive patients to your practice. Patients are demanding improved communication with their physician. A practice Web site is a start, but the adoption of a fully functional, interactive Web site with patient portal solutions will not only improve patient-to-provider relationships but will also give the patient access to your practice from anywhere, at any time of the day. Furthermore, these solutions can help practices increase efficiencies and revenue, while reducing operating costs. With the American Recovery and Reinvestment Act of 2009 and other incentives for healthcare information technology adoption, the time is right for your practice to consider implementing technology that will bring considerable value to your practice and also increase patient satisfaction.

Improving the review of standard operating procedures: a novel electronic system for compounding pharmacies.

PubMed

Brensel, Robert; Brensel, Scott; Ng, Amy

2013-01-01

Since the New England Compounding Center disaster in 2012, the importance of following correct procedures during every phase of customized pharmacy has been a focus of governmental interest and action as well as public scrutiny. Many pharmacies rely on the rote review of standard operating procedures to ensure that staff members understand and follow protocols that ensure the safety and potency of all compounds prepared, but that approach to continuing education can be cumbersome and needlessly time-consuming. In addition, documenting and retrieving evidence of employee competence can be difficult. In this article, we describe our use of online technology to improve our methods of educating staff about the full range of standard operating procedures that must be followed in our pharmacy. The system we devised and implemented has proven to be effective, easy to update and maintain, very inexpensive, and user friendly. Its use has reduced the time previously required for a read-over review of standard operating procedures from 30 or 40 minutes to 5 or 10 minutes in weekly staff meetings, and we can now easily document and access proof of employees' comprehension of that content. It is our hope that other small compounding pharmacies will also find this system of online standard operating procedure review helpful.

An application of randomization for detecting evidence of thermoregulation in timber rattlesnakes (Crotalus horridus) from northwest Arkansas.

PubMed

Wills, C A; Beaupre, S J

2000-01-01

Most reptiles maintain their body temperatures within normal functional ranges through behavioral thermoregulation. Under some circumstances, thermoregulation may be a time-consuming activity, and thermoregulatory needs may impose significant constraints on the activities of ectotherms. A necessary (but not sufficient) condition for demonstrating thermoregulation is a difference between observed body temperature distributions and available operative temperature distributions. We examined operative and body temperature distributions of the timber rattlesnake (Crotalus horridus) for evidence of thermoregulation. Specifically, we compared the distribution of available operative temperatures in the environment to snake body temperatures during August and September. Operative temperatures were measured using 48 physical models that were randomly deployed in the environment and connected to a Campbell CR-21X data logger. Body temperatures (n=1,803) were recorded from 12 radiotagged snakes using temperature-sensitive telemetry. Separate randomization tests were conducted for each hour of day within each month. Actual body temperature distributions differed significantly from operative temperature distributions at most time points considered. Thus, C. horridus exhibits a necessary (but not sufficient) condition for demonstrating thermoregulation. However, unlike some desert ectotherms, we found no compelling evidence for thermal constraints on surface activity. Randomization may prove to be a powerful technique for drawing inferences about thermoregulation without reliance on studies of laboratory thermal preference.

Development of a real-time microchip PCR system for portable plant disease diagnosis.

PubMed

Koo, Chiwan; Malapi-Wight, Martha; Kim, Hyun Soo; Cifci, Osman S; Vaughn-Diaz, Vanessa L; Ma, Bo; Kim, Sungman; Abdel-Raziq, Haron; Ong, Kevin; Jo, Young-Ki; Gross, Dennis C; Shim, Won-Bo; Han, Arum

2013-01-01

Rapid and accurate detection of plant pathogens in the field is crucial to prevent the proliferation of infected crops. Polymerase chain reaction (PCR) process is the most reliable and accepted method for plant pathogen diagnosis, however current conventional PCR machines are not portable and require additional post-processing steps to detect the amplified DNA (amplicon) of pathogens. Real-time PCR can directly quantify the amplicon during the DNA amplification without the need for post processing, thus more suitable for field operations, however still takes time and require large instruments that are costly and not portable. Microchip PCR systems have emerged in the past decade to miniaturize conventional PCR systems and to reduce operation time and cost. Real-time microchip PCR systems have also emerged, but unfortunately all reported portable real-time microchip PCR systems require various auxiliary instruments. Here we present a stand-alone real-time microchip PCR system composed of a PCR reaction chamber microchip with integrated thin-film heater, a compact fluorescence detector to detect amplified DNA, a microcontroller to control the entire thermocycling operation with data acquisition capability, and a battery. The entire system is 25 × 16 × 8 cm(3) in size and 843 g in weight. The disposable microchip requires only 8-µl sample volume and a single PCR run consumes 110 mAh of power. A DNA extraction protocol, notably without the use of liquid nitrogen, chemicals, and other large lab equipment, was developed for field operations. The developed real-time microchip PCR system and the DNA extraction protocol were used to successfully detect six different fungal and bacterial plant pathogens with 100% success rate to a detection limit of 5 ng/8 µl sample.

Development of a Real-Time Microchip PCR System for Portable Plant Disease Diagnosis

PubMed Central

Kim, Hyun Soo; Cifci, Osman S.; Vaughn-Diaz, Vanessa L.; Ma, Bo; Kim, Sungman; Abdel-Raziq, Haron; Ong, Kevin; Jo, Young-Ki; Gross, Dennis C.; Shim, Won-Bo; Han, Arum

2013-01-01

Rapid and accurate detection of plant pathogens in the field is crucial to prevent the proliferation of infected crops. Polymerase chain reaction (PCR) process is the most reliable and accepted method for plant pathogen diagnosis, however current conventional PCR machines are not portable and require additional post-processing steps to detect the amplified DNA (amplicon) of pathogens. Real-time PCR can directly quantify the amplicon during the DNA amplification without the need for post processing, thus more suitable for field operations, however still takes time and require large instruments that are costly and not portable. Microchip PCR systems have emerged in the past decade to miniaturize conventional PCR systems and to reduce operation time and cost. Real-time microchip PCR systems have also emerged, but unfortunately all reported portable real-time microchip PCR systems require various auxiliary instruments. Here we present a stand-alone real-time microchip PCR system composed of a PCR reaction chamber microchip with integrated thin-film heater, a compact fluorescence detector to detect amplified DNA, a microcontroller to control the entire thermocycling operation with data acquisition capability, and a battery. The entire system is 25×16×8 cm3 in size and 843 g in weight. The disposable microchip requires only 8-µl sample volume and a single PCR run consumes 110 mAh of power. A DNA extraction protocol, notably without the use of liquid nitrogen, chemicals, and other large lab equipment, was developed for field operations. The developed real-time microchip PCR system and the DNA extraction protocol were used to successfully detect six different fungal and bacterial plant pathogens with 100% success rate to a detection limit of 5 ng/8 µl sample. PMID:24349341

77 FR 60685 - Proposed Extension of Approval of Information Collection; Comment Request-Electrically Operated...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-04

... Information Collection; Comment Request--Electrically Operated Toys and Children's Articles AGENCY: Consumer... electrically operated toys and children's articles. The collection of information consists of testing and... Electrically Operated Articles Intended for Use by Children,'' codified at 16 CFR part 1505. The Commission...

Postreinforcement Pause in Grocery Shopping: Comparing Interpurchase Times across Products and Consumers

ERIC Educational Resources Information Center

Oliveira-Castro, Jorge M.; James, Victoria K.; Foxall, Gordon R.

2007-01-01

Purchase probability as a function of interpurchase time was examined through comparison of findings from laboratory experiments on reinforcement schedules and from marketing investigations of consumers' interpurchase time. Panel data, based on a sample of 80 consumers who purchased nine supermarket food products during 16 weeks, were used. For…

Improving striping operations through system optimization - phase 2 : final report.

DOT National Transportation Integrated Search

2016-07-01

Striping operations generate a significant workload for MoDOT maintenance operations. The requirement for each striping crew : to replenish its stock of paint and other consumable items from a bulk storage facility, along with the necessity to make s...

75 FR 27051 - Privacy Act of 1974: System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-13

... address and appears below: DOT/FMCSA 004 SYSTEM NAME: National Consumer Complaint Database (NCCDB.... A system, database, and procedures for filing and logging consumer complaints relating to household... are stored in an automated system operated and maintained at the Volpe National Transportation Systems...

Illiteracy, Financial Services and Social Exclusion.

ERIC Educational Resources Information Center

Hajaj, Khaldoun

Despite calls by consumer advocates for Australia's governments and financial services institutions to provide consumers with resources to help them understand how the financial services sector operates, financial education remains something that most Australians gain by default. Research conducted in the United Kingdom and United States, has…

Problems of Value Measurement for a Theory of Induction and Decisions

DTIC Science & Technology

1956-01-01

interest in actions and goals: add to these operations research, social psychology, consumer research, psychoanalysis , law, to 53 54 THIRD BERKELEY...anthropology, psychoanalysis , psy- chology, ethics, industrial relations, consumer research [3]. We have no method of evalu- ating the results obtained

Leadership and Characteristics of Nonprofit Mental Health Peer-Run Organizations Nationwide

PubMed Central

Ostrow, Laysha; Hayes, Stephania L.

2015-01-01

Objective Mental health peer-run organizations are nonprofits providing venues for support and advocacy among people diagnosed as having mental disorders. It has been proposed that consumer involvement is essential to their operations. This study reported organizational characteristics of peer-run organizations nationwide and how these organizations differ by degree of consumer control. Methods Data were from the 2012 National Survey of Peer-Run Organizations. The analyses described the characteristics of the organizations (N = 380) on five domains of nonprofit research, comparing results for organizations grouped by degree of involvement by consumers in the board of directors. Results Peer-run organizations provided a range of supports and educational and advocacy activities and varied in their capacity and resources. Some variation was explained by the degree of consumer control. Conclusions These organizations seemed to be operating consistently with evidence on peer-run models. The reach of peer-run organizations, and the need for in-depth research, continues to grow. PMID:25639988

Maintenance and supply options

NASA Technical Reports Server (NTRS)

1988-01-01

The object of the Maintenance and Supply Option was to develop a high level operational philosophy related to maintenance and supply operations and incorporate these concepts into the Lunar Base Study. Specific products to be generated during this task were three trade studies and a conceptual design of the Logistic Supply Module. The crew size study was performed to evaluate crew sizes from the baseline size of four to a crew size of eight and determine the preferred crew size. The second trade study was to determine the impact of extending surface stay times and recommend a preferred duration of stay time as a function of crew, consumables, and equipment support capabilities. The third trade study was an evaluation of packaging and storage methods to determine the preferred logistics approach to support the lunar base. A modified scenario was developed and served as the basis of the individual trade studies. Assumptions and guidelines were also developed from experience with Apollo programs, Space Shuttle operations, and Space Station studies. With this information, the trade studies were performed and a conceptual design for the Logistic Supply Module was developed.

Peri-operative communication patterns and media usage--implications for systems design.

PubMed

Karlsen, Ero S; Toussaint, Pieter Jelle

2010-01-01

Inter-hospital communication amounts for a great deal of clinicians' work time. While communication is essential to coordinate care, it can also be time consuming and interruptive, and breakdown in communication is an important source of medical errors. One contributor to the interruptive nature of communication is the use of synchronous media, and there is clearly a potential for novel technologies. To assess communication patterns and media usage we performed an ethnographic field study in the peri-operative environment at a Norwegian hospital, as well as interviews with nurses. We analyze the results with regards to choice of media, characteristics of the conversations taking place and meta-messages, and account for addressing, obtrusiveness and information richness in the message exchanges. We find a relative high degree of interruptiveness in communication, and ascribe it to 1) a lack of situational awareness between locations in the peri-operative domain, as well as 2) use of synchronous media. This suggests that design of novel technology for intra-hospital communication should aim at supporting sender-receiver awareness and signaling of availability.

Performance of plasma trigonelline as a marker of coffee consumption in an epidemiologic setting.

PubMed

Midttun, Øivind; Ulvik, Arve; Nygård, Ottar; Ueland, Per M

2018-05-15

Coffee is a widely consumed beverage, and studies suggest that drinking coffee has beneficial health effects. The phytohormone trigonelline is present in large amounts in coffee beans, and circulating concentrations of trigonelline have been shown to be positively related to dietary intake of coffee and to increase significantly after the consumption of a bolus dose of coffee. We cross-sectionally investigated the utility of plasma trigonelline as a marker of coffee consumption in an epidemiologic setting. We secondarily investigated if coffee intake is related to plasma concentrations of vitamin B-3 (niacin) forms. In a Norwegian cohort of 3503 participants, we combined questionnaire data on the number of cups of coffee consumed per day with plasma trigonelline to evaluate trigonelline as a marker of coffee intake. The suitability of plasma trigonelline to discriminate those not consuming from those consuming coffee was investigated by receiver operating characteristic (ROC) analysis. Plasma collected at 2 time points 1 y apart was used to determine the within-person reproducibility of trigonelline. We found that plasma trigonelline concentrations increased strongly with increasing amounts of coffee consumed. ROC analysis showed that trigonelline had an area under the curve of 0.92 (95% CI: 0.90, 0.94) for distinguishing coffee abstainers from coffee drinkers. Plasma trigonelline had a good within-person reproducibility (0.66; 95% CI: 0.64, 0.68) for samples collected 1 y apart. The amount of coffee consumed was not associated with plasma concentrations of the niacin vitamers nicotinamide and N1-methylnicotinamide. Plasma trigonelline performs well as a marker of coffee intake. Data used in this study were derived from the clinical trial registered at www.clinicaltrials.gov as NCT00354081.

The food-service industry, dietary guidelines and change.

PubMed

Hughes, R G; Harvey, P W; Heywood, P F

1997-08-01

The influence of the food-service industry on compliance with the Australian dietary guidelines was investigated through three separate methods of data collection and analysis: a telephone survey of 1683 randomly selected Brisbane residents; telephone interviews with 69 food-service-industry operators and 10 face-to-face interviews with key stakeholders in industry and government. Nearly 40 per cent of respondents had consumed foods prepared by the food-service industry at least once on the day before the interview, mainly from restaurants, cafes and takeaway shops, in the form of fast-food or snacks. Consumption of these foods declined with age. Those consuming foods prepared by the food-service industry ate significantly less fruit, vegetables and dairy food and were therefore less likely to comply with the dietary guidelines. Outcomes from interviews with operators in the food-service industry show that food choices offered to consumers were the result of a dynamic interaction between consumer demand and operators' own tastes and perceptions of food quality. Key informant interviews show that public health nutrition programs will have limited effect without supportive environmental changes in the food-service industry supply. An effective means of increasing the likelihood of compliance with the Australian dietary guidelines will be to encourage food suppliers in ways that address their core business concerns simultaneously with the goals of health professionals.

78 FR 4725 - Escrow Requirements Under the Truth in Lending Act (Regulation Z)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-22

...The Bureau of Consumer Financial Protection (Bureau) is publishing a final rule that amends Regulation Z (Truth in Lending) to implement certain amendments to the Truth in Lending Act made by the Dodd-Frank Wall Street Reform and Consumer Protection Act (Dodd-Frank Act). Regulation Z currently requires creditors to establish escrow accounts for higher-priced mortgage loans secured by a first lien on a principal dwelling. The rule implements statutory changes made by the Dodd-Frank Act that lengthen the time for which a mandatory escrow account established for a higher-priced mortgage loan must be maintained. The rule also exempts certain transactions from the statute's escrow requirement. The primary exemption applies to mortgage transactions extended by creditors that operate predominantly in rural or underserved areas, originate a limited number of first-lien covered transactions, have assets below a certain threshold, and do not maintain escrow accounts on mortgage obligations they currently service.

A highly linear fully integrated powerline filter for biopotential acquisition systems.

PubMed

Alzaher, Hussain A; Tasadduq, Noman; Mahnashi, Yaqub

2013-10-01

Powerline interference is one of the most dominant problems in detection and processing of biopotential signals. This work presents a new fully integrated notch filter exhibiting high linearity and low power consumption. High filter linearity is preserved utilizing active-RC approach while IC implementation is achieved through replacing passive resistors by R-2R ladders achieving area saving of approximately 120 times. The filter design is optimized for low power operation using an efficient circuit topology and an ultra-low power operational amplifier. Fully differential implementation of the proposed filter shows notch depth of 43 dB (78 dB for 4th-order) with THD of better than -70 dB while consuming about 150 nW from 1.5 V supply.

Reshaping of large aeronautical structural parts: A simplified simulation approach

NASA Astrophysics Data System (ADS)

Mena, Ramiro; Aguado, José V.; Guinard, Stéphane; Huerta, Antonio

2018-05-01

Large aeronautical structural parts present important distortions after machining. This problem is caused by the presence of residual stresses, which are developed during previous manufacturing steps (quenching). Before being put into service, the nominal geometry is restored by means of mechanical methods. This operation is called reshaping and exclusively depends on the skills of a well-trained and experienced operator. Moreover, this procedure is time consuming and nowadays, it is only based on a trial and error approach. Therefore, there is a need at industrial level to solve this problem with the support of numerical simulation tools. By using a simplification hypothesis, it was found that the springback phenomenon behaves linearly and it allows developing a strategy to implement reshaping at an industrial level.

Spacecraft Fire Safety and Microgravity Combustion Research

NASA Technical Reports Server (NTRS)

Tien, James S.; Ferkul, Paul (Technical Monitor)

2001-01-01

Fire safety is an important concern in our daily lives and it plays a special role in the human presence in space. In a spacecraft, the outside environment is hostile and the opportunity to escape is small. Rescue missions are difficult and time consuming. As a result, we should avoid the occurrence of fires in spacecraft as much as possible. If a fire occurs, we need to keep it small and under control. This implies that the materials used on board the spacecraft should be screened carefully, all the machines and devices need to be operated without accident, and fire detectors have to function properly. Once a fire is detected, it can be extinguished quickly and the cabin can be cleaned up to restore operation and sustain life.

Characteristics associated with organizational independence in consumer-operated service organizations.

PubMed

Tanenbaum, Sandra J

2011-01-01

This research compares two types of consumer organizations in one state in order to explore the significance of organizational independence for internal structure/operations and external relationships. The first type, consumeroperated service organizations (COSOs), are independent and fully self-governing; the second are peer-support service organizations (PSSOs), which are part of larger non-consumer entities. Mail surveys were completed by COSO and PSSO directors of a geographically representative sample of organizations; telephone interviews were conducted with a sub-sample. Owing to small sample size, matched COSO-PSSO pairs were analyzed using non-parametric statistics. COSOs and PSSOs are similar in some ways, e.g., types of services provided, but significantly different on internal variables, such as budget size, and external variables, such as number of relationships with community groups. Organizational independence appears to be a significant characteristic for consumer service organizations and should be encouraged by funders and among participants. Funders might establish administrative and/or programmatic measures to support consumer organizations that are independent or moving toward independence; their participants would also benefit from the provision, by authorities or advocates, of materials to guide organizations toward, for example, 501(c)3 status.

Real-time measurements of airborne biologic particles using fluorescent particle counter to evaluate microbial contamination: results of a comparative study in an operating theater.

PubMed

Dai, Chunyang; Zhang, Yan; Ma, Xiaoling; Yin, Meiling; Zheng, Haiyang; Gu, Xuejun; Xie, Shaoqing; Jia, Hengmin; Zhang, Liang; Zhang, Weijun

2015-01-01

Airborne bacterial contamination poses a risk for surgical site infection, and routine surveillance of airborne bacteria is important. Traditional methods for detecting airborne bacteria are time consuming and strenuous. Measurement of biologic particle concentrations using a fluorescent particle counter is a novel method for evaluating air quality. The current study was to determine whether the number of biologic particles detected by the fluorescent particle counter can be used to indicate airborne bacterial counts in operating rooms. The study was performed in an operating theater at a university hospital in Hefei, China. The number of airborne biologic particles every minute was quantified using a fluorescent particle counter. Microbiologic air sampling was performed every 30 minutes using an Andersen air sampler (Pusong Electronic Instruments, Changzhou, China). Correlations between the 2 different methods were analyzed by Pearson correlation coefficients. A significant correlation was observed between biologic particle and bacterial counts (Pearson correlation coefficient = 0.76), and the counting results from 2 methods both increased substantially between operations, corresponding with human movements in the operating room. Fluorescent particle counters show potential as important tools for monitoring bacterial contamination in operating theatres. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Monitoring scale scores over time via quality control charts, model-based approaches, and time series techniques.

PubMed

Lee, Yi-Hsuan; von Davier, Alina A

2013-07-01

Maintaining a stable score scale over time is critical for all standardized educational assessments. Traditional quality control tools and approaches for assessing scale drift either require special equating designs, or may be too time-consuming to be considered on a regular basis with an operational test that has a short time window between an administration and its score reporting. Thus, the traditional methods are not sufficient to catch unusual testing outcomes in a timely manner. This paper presents a new approach for score monitoring and assessment of scale drift. It involves quality control charts, model-based approaches, and time series techniques to accommodate the following needs of monitoring scale scores: continuous monitoring, adjustment of customary variations, identification of abrupt shifts, and assessment of autocorrelation. Performance of the methodologies is evaluated using manipulated data based on real responses from 71 administrations of a large-scale high-stakes language assessment.

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2010 CFR

2010-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... the lease contract, so long as all disclosures are given at the same time. Alternatively, all...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2011 CFR

2011-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... the lease contract, so long as all disclosures are given at the same time. Alternatively, all...

Time trends and patterns of reported egg consumption in the U.S. by sociodemographic characteristics

USDA-ARS?s Scientific Manuscript database

Objectives: To 1) describe time trends of the percentage of individuals in the U.S that consume eggs, 2) describe time trends of the daily amount of eggs consumed per day, and 3) examine differences in the amount of eggs consumed per day; overall and by gender, age, income, education, race-ethnicit...

12 CFR Appendix I to Part 226 - Federal Enforcement Agencies

Code of Federal Regulations, 2010 CFR

2010-01-01

.... Retail, Department Stores, Consumer Finance Companies, All Other Creditors, and All Nonbank Credit Card... Office in which they operate.) Division of Credit Practices, Bureau of Consumer Protection, Federal Trade.... Federal Credit Unions Regional office of the National Credit Union Administration serving the area in...

16 CFR 1211.13 - Inherent force activated secondary door sensors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... sensors. 1211.13 Section 1211.13 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... § 1211.13 Inherent force activated secondary door sensors. (a) Normal operation test. (1) A force activated door sensor of a door system installed according to the installation instructions shall actuate...

16 CFR 1211.13 - Inherent force activated secondary door sensors.

Code of Federal Regulations, 2014 CFR

2014-01-01

... sensors. 1211.13 Section 1211.13 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... § 1211.13 Inherent force activated secondary door sensors. (a) Normal operation test. (1) A force activated door sensor of a door system installed according to the installation instructions shall actuate...

16 CFR 1211.13 - Inherent force activated secondary door sensors.

Code of Federal Regulations, 2012 CFR

2012-01-01

... sensors. 1211.13 Section 1211.13 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... § 1211.13 Inherent force activated secondary door sensors. (a) Normal operation test. (1) A force activated door sensor of a door system installed according to the installation instructions shall actuate...

DEVELOPMENT OF AN INNOVATIVE SPRAY DISPENSER TO REDUCE INDOOR AIR EMISSIONS FROM AEROSOL CONSUMER PRODUCTS

EPA Science Inventory

The report presents the operating principles and performance of a new type of spray nozzle. This nozzle, termed a "ligament-controlled effervescent atomizer," was developed to allow consumer product manufacturers to replace volatile organic compound (VOC) solvents with water, and...

Minimally invasive video-assisted thyroidectomy: Ascending the learning curve

PubMed Central

Capponi, Michela Giulii; Bellotti, Carlo; Lotti, Marco; Ansaloni, Luca

2015-01-01

BACKGROUND: Minimally invasive video-assisted thyroidectomy (MIVAT) is a technically demanding procedure and requires a surgical team skilled in both endocrine and endoscopic surgery. The aim of this report is to point out some aspects of the learning curve of the video-assisted thyroid surgery, through the analysis of our preliminary series of procedures. PATIENTS AND METHODS: Over a period of 8 months, we selected 36 patients for minimally invasive video-assisted surgery of the thyroid. The patients were considered eligible if they presented with a nodule not exceeding 35 mm and total thyroid volume <20 ml; presence of biochemical and ultrasound signs of thyroiditis and pre-operative diagnosis of cancer were exclusion criteria. We analysed surgical results, conversion rate, operating time, post-operative complications, hospital stay and cosmetic outcomes of the series. RESULTS: We performed 36 total thyroidectomy and in one case we performed a consensual parathyroidectomy. The procedure was successfully carried out in 33 out of 36 cases (conversion rate 8.3%). The mean operating time was 109 min (range: 80-241 min) and reached a plateau after 29 MIVAT. Post-operative complications included three transient recurrent nerve palsies and two transient hypocalcemias; no definitive hypoparathyroidism was registered. The cosmetic result was considered excellent by most patients. CONCLUSIONS: Advances in skills and technology allow surgeons to easily reproduce the standard open total thyroidectomy with video-assistance. Although the learning curve represents a time-consuming step, training remains a crucial point in gaining a reasonable confidence with video-assisted surgical technique. PMID:25883451

The traverse planning process for D-RATS 2010

NASA Astrophysics Data System (ADS)

Hörz, Friedrich; Lofgren, Gary E.; Gruener, John E.; Eppler, Dean B.; Skinner, James A.; Fortezzo, Corey M.; Graf, Jodi S.; Bluethmann, William J.; Seibert, Marc A.; Bell, Ernest R.

2013-10-01

This report describes the traverse planning process for the Desert Research and Technology Studies (D-RATS) 2010 field simulation of a conceptual 14-day planetary mission. This activity took place between August 23 and September 17, 2010 in the San Francisco Volcanic Field, Arizona. It focused on the utilization of two pressurized rovers and a ground-based communication system, as well as on the development of mission operation concepts for long duration, dual-rover missions. The early planning process began some 12 months prior to the actual field tests and defined the first order engineering-, flight operations, and science objectives. The detailed implementation and refinement of these objectives took place over the ensuing 10 months, resulting in a large number of technical and operational constraints that affected the actual traverse route or the cumulative Extravehicular Activity (EVA) time available for detailed field observations. The science planning proceeded from the generation of photogeologic maps of the test area, to the establishment of prioritized science objectives and associated candidate sites for detailed field exploration. The combination of operational constraints and science objectives resulted in the final design of traverse routes and time lines for each of the 24 traverses needed to support 12 field days by two rovers. Examples of daily traverses will be given that will hopefully illustrate that the design of long duration, long distance planetary traverses is a highly interdisciplinary and time-consuming collaboration between diverse engineers, flight operations personnel, human factors interests, and planetary scientists.

Alcohol operant self-administration: Investigating how alcohol-seeking behaviors predict drinking in mice using two operant approaches

PubMed Central

Blegen, Mariah B.; Silva, Daniel da Silva E; Bock, Roland; Morisot, Nadege; Ron, Dorit; Alvarez, Veronica A.

2018-01-01

Alcohol operant self-administration paradigms are critical tools for studying the neural circuits implicated in both alcohol-seeking and consummatory behaviors and for understanding the neural basis underlying alcohol-use disorders. In this study, we investigate the predictive value of two operant models of oral alcohol self-administration in mice, one in which alcohol is delivered into a cup following nose-poke responses with no accurate measurement of consumed alcohol solution, and another paradigm that provides access to alcohol via a sipper tube following lever presses and where lick rate and consumed alcohol volume can be measured. The goal was to identify a paradigm where operant behaviors such as lever presses and nose pokes, as well as other tracked behavior such as licks and head entries, can be used to reliably predict blood alcohol concentration (BAC). All mice were first exposed to alcohol in the home cage using the “drinking in the dark” (DID) procedure for 3 weeks and then were trained in alcohol self-administration using either of the operant paradigms for several weeks. Even without sucrose fading or food pre-training, mice acquired alcohol self-administration with both paradigms. However, neither lever press nor nose-poke rates were good predictors of alcohol intake or BAC. Only the lick rate and consumed alcohol were consistently and significantly correlated with BAC. Using this paradigm that accurately measures alcohol intake, unsupervised cluster analysis revealed three groups of mice: high-drinking (43%), low-drinking (37%), and non-drinking mice (20%). High-drinking mice showed faster acquisition of operant responding and achieved higher BACs than low-drinking mice. Lick rate and volume consumed varied with the alcohol concentration made available only for high- and low-drinking mice, but not for non-drinking mice. In addition, high- and low-drinking mice showed similar patterns during extinction and significant cue-induced reinstatement of seeking. Only high-drinking mice showed insensitivity to quinine adulteration, indicating a willingness to drink alcohol despite pairing with aversive stimuli. Thus, this study shows that relying on active presses is not an accurate determination of drinking behavior in mice. Only paradigms that allow for accurate measurements of consumed alcohol and/or lick rate are valid models of operant alcohol self-administration, where compulsive-like drinking could be accurately determined based on changes in alcohol intake when paired with bitter-tasting stimuli. PMID:29310048

A longitudinal model of the dynamics between HMOs' consumer-friendliness and preventive health care utilization.

PubMed

Xiao, Qian; Savage, Grant T; Zhuang, Weiling

2014-01-01

This study aims at replicating and extending Xiao and Savage's (2008) research to understand the multidimensional aspect of HMOs distinguished by HMOs' consumer-friendliness, and their relationship to consumers' preventive care utilization. This study develops a dynamic model to consider both concurrent and time lagging effects of HMOs' consumer-friendliness. Our data analysis discloses similar relationship patterns as revealed by Xiao and Savage. Additionally, our findings reveal the time-series changes of the influence of HMOs' consumer-friendliness that either the effects of early experienced HMOs' consumer-friendliness wear out totally or HMOs' consumer-friendly characteristics on the concurrent term contain most of the explanatory power.

Minimally invasive video-assisted thyroid surgery: how can we improve the learning curve?

PubMed

Castagnola, G; Giulii Cappone, M; Tierno, S M; Mezzetti, G; Centanini, F; Vetrone, I; Bellotti, C

2012-10-01

Minimally invasive video-assisted thyroidectomy (MIVAT) is a technically demanding procedure and requires a surgical team skilled in both endocrine and endoscopic surgery. A time consuming learning and training period is mandatory at the beginning of the experience. The aim of our report is to focus some aspects of the learning curve of the surgeon who practices video-assisted thyroid procedures for the first time, through the analysis of our preliminary series of 36 cases. From September 2004 to April 2005 we selected 36 patients for minimally invasive video-assisted surgery of the thyroid. The patients were considered eligible if they presented with a nodule not exceeding 35 mm in maximum diameter; total thyroid volume within normal range; absence of biochemical and echographic signs of thyroiditis. We analyzed surgical results, conversion rate, operating time, post-operative complications, hospital stay, cosmetic outcome of the series. We performed 36 total thyroidectomy. The procedure was successfully carried out in 33/36 cases. Post-operative complications included 3 transient recurrent nerve palsies and 2 transient hypocalcemias; no definitive hypoparathyroidism was registered. All patients were discharged 2 days after operation. The cosmetic result was considered excellent by most patients. Advances in skills and technology have enabled surgeons to reproduce most open surgical techniques with video-assistance or laparoscopically. Training is essential to acquire any new surgical technique and it should be organized in detail to exploit it completely.

Interactive autonomy and robotic skills

NASA Technical Reports Server (NTRS)

Kellner, A.; Maediger, B.

1994-01-01

Current concepts of robot-supported operations for space laboratories (payload servicing, inspection, repair, and ORU exchange) are mainly based on the concept of 'interactive autonomy' which implies autonomous behavior of the robot according to predefined timelines, predefined sequences of elementary robot operations and within predefined world models supplying geometrical and other information for parameter instantiation on the one hand, and the ability to override and change the predefined course of activities by human intervention on the other hand. Although in principle a very powerful and useful concept, in practice the confinement of the robot to the abstract world models and predefined activities appears to reduce the robot's stability within real world uncertainties and its applicability to non-predefined parts of the world, calling for frequent corrective interaction by the operator, which in itself may be tedious and time-consuming. Methods are presented to improve this situation by incorporating 'robotic skills' into the concept of interactive autonomy.

16 CFR 433.3 - Exemption of sellers taking or receiving open end consumer credit contracts before November 1...

Code of Federal Regulations, 2010 CFR

2010-01-01

... make loans, from time to time, directly from the creditor or indirectly by use of a credit card, check... open end consumer credit contracts before November 1, 1977 from requirements of § 433.2(a). 433.3... CONSUMERS' CLAIMS AND DEFENSES § 433.3 Exemption of sellers taking or receiving open end consumer credit...

Real-time emissions from construction equipment compared with model predictions.

PubMed

Heidari, Bardia; Marr, Linsey C

2015-02-01

The construction industry is a large source of greenhouse gases and other air pollutants. Measuring and monitoring real-time emissions will provide practitioners with information to assess environmental impacts and improve the sustainability of construction. We employed a portable emission measurement system (PEMS) for real-time measurement of carbon dioxide (CO), nitrogen oxides (NOx), hydrocarbon, and carbon monoxide (CO) emissions from construction equipment to derive emission rates (mass of pollutant emitted per unit time) and emission factors (mass of pollutant emitted per unit volume of fuel consumed) under real-world operating conditions. Measurements were compared with emissions predicted by methodologies used in three models: NONROAD2008, OFFROAD2011, and a modal statistical model. Measured emission rates agreed with model predictions for some pieces of equipment but were up to 100 times lower for others. Much of the difference was driven by lower fuel consumption rates than predicted. Emission factors during idling and hauling were significantly different from each other and from those of other moving activities, such as digging and dumping. It appears that operating conditions introduce considerable variability in emission factors. Results of this research will aid researchers and practitioners in improving current emission estimation techniques, frameworks, and databases.

77 FR 38305 - Agency Information Collection Activities; Announcement of Office of Management and Budget...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-27

...; ``Real Time'' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne...' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne Illness Outbreaks... ```Real Time' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne...

Cryogenics Testbed Laboratory Flange Baseline Configuration

NASA Technical Reports Server (NTRS)

Acuna, Marie Lei Ysabel D.

2013-01-01

As an intern at Kennedy Space Center (KSC), I was involved in research for the Fluids and Propulsion Division of the NASA Engineering (NE) Directorate. I was immersed in the Integrated Ground Operations Demonstration Units (IGODU) project for the majority of my time at KSC, primarily with the Ground Operations Demonstration Unit Liquid Oxygen (GODU L02) branch of IGODU. This project was established to develop advancements in cryogenic systems as a part of KSC's Advanced Exploration Systems (AES) program. The vision of AES is to develop new approaches for human exploration, and operations in and beyond low Earth orbit. Advanced cryogenic systems are crucial to minimize the consumable losses of cryogenic propellants, develop higher performance launch vehicles, and decrease operations cost for future launch programs. During my internship, I conducted a flange torque tracking study that established a baseline configuration for the flanges in the Simulated Propellant Loading System (SPLS) at the KSC Cryogenics Test Laboratory (CTL) - the testing environment for GODU L02.

Neural Network and Regression Soft Model Extended for PAX-300 Aircraft Engine

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Hopkins, Dale A.

2002-01-01

In fiscal year 2001, the neural network and regression capabilities of NASA Glenn Research Center's COMETBOARDS design optimization testbed were extended to generate approximate models for the PAX-300 aircraft engine. The analytical model of the engine is defined through nine variables: the fan efficiency factor, the low pressure of the compressor, the high pressure of the compressor, the high pressure of the turbine, the low pressure of the turbine, the operating pressure, and three critical temperatures (T(sub 4), T(sub vane), and T(sub metal)). Numerical Propulsion System Simulation (NPSS) calculations of the specific fuel consumption (TSFC), as a function of the variables can become time consuming, and numerical instabilities can occur during these design calculations. "Soft" models can alleviate both deficiencies. These approximate models are generated from a set of high-fidelity input-output pairs obtained from the NPSS code and a design of the experiment strategy. A neural network and a regression model with 45 weight factors were trained for the input/output pairs. Then, the trained models were validated through a comparison with the original NPSS code. Comparisons of TSFC versus the operating pressure and of TSFC versus the three temperatures (T(sub 4), T(sub vane), and T(sub metal)) are depicted in the figures. The overall performance was satisfactory for both the regression and the neural network model. The regression model required fewer calculations than the neural network model, and it produced marginally superior results. Training the approximate methods is time consuming. Once trained, the approximate methods generated the solution with only a trivial computational effort, reducing the solution time from hours to less than a minute.

Progress and challenges associated with halal authentication of consumer packaged goods.

PubMed

Premanandh, Jagadeesan; Bin Salem, Samara

2017-11-01

Abusive business practices are increasingly evident in consumer packaged goods. Although consumers have the right to protect themselves against such practices, rapid urbanization and industrialization result in greater distances between producers and consumers, raising serious concerns on the supply chain. The operational complexities surrounding halal authentication pose serious challenges on the integrity of consumer packaged goods. This article attempts to address the progress and challenges associated with halal authentication. Advancement and concerns on the application of new, rapid analytical methods for halal authentication are discussed. The significance of zero tolerance policy in consumer packaged foods and its impact on analytical testing are presented. The role of halal assurance systems and their challenges are also considered. In conclusion, consensus on the establishment of one standard approach coupled with a sound traceability system and constant monitoring would certainly improve and ensure halalness of consumer packaged goods. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

47 CFR 73.674 - Digital television transition notices by broadcasters.

Code of Federal Regulations, 2013 CFR

2013-10-01

... is operating under such an extension, must continue its DTV consumer education campaign until the... terminates analog service, it must continue to comply with the requirements of the Consumer Education Campaign Option that it has elected, except that the content of all on-air education must be revised to...

47 CFR 73.674 - Digital television transition notices by broadcasters.

Code of Federal Regulations, 2012 CFR

2012-10-01

... is operating under such an extension, must continue its DTV consumer education campaign until the... terminates analog service, it must continue to comply with the requirements of the Consumer Education Campaign Option that it has elected, except that the content of all on-air education must be revised to...

47 CFR 73.674 - Digital television transition notices by broadcasters.

Code of Federal Regulations, 2014 CFR

2014-10-01

... is operating under such an extension, must continue its DTV consumer education campaign until the... terminates analog service, it must continue to comply with the requirements of the Consumer Education Campaign Option that it has elected, except that the content of all on-air education must be revised to...

The Consumerization of IT: Pendulum or Wrecking Ball?

ERIC Educational Resources Information Center

Demski, Jennifer

2011-01-01

The burgeoning consumer-tech market is creating new challenges for higher education IT departments. As increased expectations of mobility and connectivity have students and faculty looking to consumer technology to meet their academic needs, IT must revamp operations and infrastructure to meet the demand, while keeping security risks and budgets…

77 FR 24687 - Impact of Overdraft Programs on Consumers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-25

..., is extended. Responses must now be received on or before June 29, 2012. ADDRESSES: You may submit...' operating policies; The economics of overdraft programs; and Long-term impacts on Consumers. The comment... period allotted for comments received pursuant to the Overdraft Notice. The comment period will now close...

Consumer Education in the Science Curriculum.

ERIC Educational Resources Information Center

Kowalski, Stephen W.

In this monograph, the implementation of consumer education topics into the science curriculum of secondary schools is advocated. Not only is the need for such activities explained, but several suggested instructional topics are provided. One area of recommended study is that of product comparison. A model outline of operation is provided, along…

On the Evolutionary Bases of Consumer Reinforcement

ERIC Educational Resources Information Center

Nicholson, Michael; Xiao, Sarah Hong

2010-01-01

This article locates consumer behavior analysis within the modern neo-Darwinian synthesis, seeking to establish an interface between the ultimate-level theorizing of human evolutionary psychology and the proximate level of inquiry typically favored by operant learning theorists. Following an initial overview of the central tenets of neo-Darwinism,…

All-Terrain Vehicles. Hearing before the Subcommittee on Commerce, Consumer Protection, and Competitiveness of the Committee on Energy and Commerce. House of Representatives, One Hundredth Congress, First Session.

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. House Committee on Energy and Commerce.

As part of a review of the operation of the Consumer Product Safety Commission (CPSC), a hearing was held to receive testimony concerning the safety of all-terrain vehicles (ATVs) and recommendations for protection of consumers who purchase them. Of particular interest was the question of whether the Commission, due to budget cuts or reliance on…

Application of information theory methods to food web reconstruction

USGS Publications Warehouse

Moniz, L.J.; Cooch, E.G.; Ellner, S.P.; Nichols, J.D.; Nichols, J.M.

2007-01-01

In this paper we use information theory techniques on time series of abundances to determine the topology of a food web. At the outset, the food web participants (two consumers, two resources) are known; in addition we know that each consumer prefers one of the resources over the other. However, we do not know which consumer prefers which resource, and if this preference is absolute (i.e., whether or not the consumer will consume the non-preferred resource). Although the consumers and resources are identified at the beginning of the experiment, we also provide evidence that the consumers are not resources for each other, and the resources do not consume each other. We do show that there is significant mutual information between resources; the model is seasonally forced and some shared information between resources is expected. Similarly, because the model is seasonally forced, we expect shared information between consumers as they respond to the forcing of the resources. The model that we consider does include noise, and in an effort to demonstrate that these methods may be of some use in other than model data, we show the efficacy of our methods with decreasing time series size; in this particular case we obtain reasonably clear results with a time series length of 400 points. This approaches ecological time series lengths from real systems.

The rise of ocean giants: maximum body size in Cenozoic marine mammals as an indicator for productivity in the Pacific and Atlantic Oceans.

PubMed

Pyenson, Nicholas D; Vermeij, Geerat J

2016-07-01

Large consumers have ecological influence disproportionate to their abundance, although this influence in food webs depends directly on productivity. Evolutionary patterns at geologic timescales inform expectations about the relationship between consumers and productivity, but it is very difficult to track productivity through time with direct, quantitative measures. Based on previous work that used the maximum body size of Cenozoic marine invertebrate assemblages as a proxy for benthic productivity, we investigated how the maximum body size of Cenozoic marine mammals, in two feeding guilds, evolved over comparable temporal and geographical scales. First, maximal size in marine herbivores remains mostly stable and occupied by two different groups (desmostylians and sirenians) over separate timeframes in the North Pacific Ocean, while sirenians exclusively dominated this ecological mode in the North Atlantic. Second, mysticete whales, which are the largest Cenozoic consumers in the filter-feeding guild, remained in the same size range until a Mio-Pliocene onset of cetacean gigantism. Both vertebrate guilds achieved very large size only recently, suggesting that different trophic mechanisms promoting gigantism in the oceans have operated in the Cenozoic than in previous eras. © 2016 The Authors.

Implementing real-time robotic systems using CHIMERA II

NASA Technical Reports Server (NTRS)

Stewart, David B.; Schmitz, Donald E.; Khosla, Pradeep K.

1990-01-01

A description is given of the CHIMERA II programming environment and operating system, which was developed for implementing real-time robotic systems. Sensor-based robotic systems contain both general- and special-purpose hardware, and thus the development of applications tends to be a time-consuming task. The CHIMERA II environment is designed to reduce the development time by providing a convenient software interface between the hardware and the user. CHIMERA II supports flexible hardware configurations which are based on one or more VME-backplanes. All communication across multiple processors is transparent to the user through an extensive set of interprocessor communication primitives. CHIMERA II also provides a high-performance real-time kernel which supports both deadline and highest-priority-first scheduling. The flexibility of CHIMERA II allows hierarchical models for robot control, such as NASREM, to be implemented with minimal programming time and effort.

Time-dependent resilience assessment and improvement of urban infrastructure systems

NASA Astrophysics Data System (ADS)

Ouyang, Min; Dueñas-Osorio, Leonardo

2012-09-01

This paper introduces an approach to assess and improve the time-dependent resilience of urban infrastructure systems, where resilience is defined as the systems' ability to resist various possible hazards, absorb the initial damage from hazards, and recover to normal operation one or multiple times during a time period T. For different values of T and its position relative to current time, there are three forms of resilience: previous resilience, current potential resilience, and future potential resilience. This paper mainly discusses the third form that takes into account the systems' future evolving processes. Taking the power transmission grid in Harris County, Texas, USA as an example, the time-dependent features of resilience and the effectiveness of some resilience-inspired strategies, including enhancement of situational awareness, management of consumer demand, and integration of distributed generators, are all simulated and discussed. Results show a nonlinear nature of resilience as a function of T, which may exhibit a transition from an increasing function to a decreasing function at either a threshold of post-blackout improvement rate, a threshold of load profile with consumer demand management, or a threshold number of integrated distributed generators. These results are further confirmed by studying a typical benchmark system such as the IEEE RTS-96. Such common trends indicate that some resilience strategies may enhance infrastructure system resilience in the short term, but if not managed well, they may compromise practical utility system resilience in the long run.

Time-dependent resilience assessment and improvement of urban infrastructure systems.

PubMed

Ouyang, Min; Dueñas-Osorio, Leonardo

2012-09-01

This paper introduces an approach to assess and improve the time-dependent resilience of urban infrastructure systems, where resilience is defined as the systems' ability to resist various possible hazards, absorb the initial damage from hazards, and recover to normal operation one or multiple times during a time period T. For different values of T and its position relative to current time, there are three forms of resilience: previous resilience, current potential resilience, and future potential resilience. This paper mainly discusses the third form that takes into account the systems' future evolving processes. Taking the power transmission grid in Harris County, Texas, USA as an example, the time-dependent features of resilience and the effectiveness of some resilience-inspired strategies, including enhancement of situational awareness, management of consumer demand, and integration of distributed generators, are all simulated and discussed. Results show a nonlinear nature of resilience as a function of T, which may exhibit a transition from an increasing function to a decreasing function at either a threshold of post-blackout improvement rate, a threshold of load profile with consumer demand management, or a threshold number of integrated distributed generators. These results are further confirmed by studying a typical benchmark system such as the IEEE RTS-96. Such common trends indicate that some resilience strategies may enhance infrastructure system resilience in the short term, but if not managed well, they may compromise practical utility system resilience in the long run.

Consumer’s market analysis of products based on cassava

NASA Astrophysics Data System (ADS)

Unteawati, Bina; Fitriani; Fatih, Cholid

2018-03-01

Cassava product has the important role for enhancing household's income in rural. Cassava as raw material food is plentiful as local food in Lampung. Cassava product is one of strategic value addition activities. Value additional activities are a key to create income source enrichment in rural. The household was product cassava as a snack or additional food. Their product cassava was operated in small-scale, traditional, and discontinuous production. They have been lacked in technology, capital, and market access. Measurement the sustainability of their business is important. The market has driven the business globally. This research aims to (1) describe the cassava demand to locally product cassava in rural and (2) analysis the consumer's perception of cassava product. Research take placed in Lampung Province, involved Bandar Lampung and Metro City, Pringsewu, Pesawaran, Central Lampung, and East Lampung district. It is held in February until April 2017. Data were analyzed by descriptive statistic and multidimensional scaling. Based on the analysis conclude that (1) the demand of product cassava from rural was massive in volume and regularity with the enormous transaction. This fact is very important to role business cycles. Consumers demand continuously will lead the production of cassava product sustain. Producers of product cassava will consume fresh cassava for the farmer. Consumption of fresh cassava for home industry regularly in rural will develop balancing in fresh cassava price in the farming gate (2) The consumer's perception on cassava product in the different market showed that they prefer much to consume cassava chips as cassava product products than other. Next are crackers, opak, and tiwul rice. Urban consumers prefer product products as snacks (chips, crumbs, and opak), with consumption frequency of 2-5 times per week and volume of 1-3 kg purchases. Consumers in rural were more frequent with daily consumption frequency. Multidimensional scaling analysis performed that price of cassava product was the centre of product attribute.

Consumer confidence in the safety of food and newspaper coverage of food safety issues: a longitudinal perspective.

PubMed

de Jonge, Janneke; Van Trijp, Hans; Renes, Reint Jan; Frewer, Lynn J

2010-01-01

This study develops a longitudinal perspective on consumer confidence in the safety of food to explore if, how, and why consumer confidence changes over time. In the first study, a theory-based monitoring instrument for consumer confidence in the safety of food was developed and validated. The monitoring instrument assesses consumer confidence together with its determinants. Model and measurement invariance were validated rigorously before developments in consumer confidence in the safety of food and its determinants were investigated over time. The results from the longitudinal analysis show that across four waves of annual data collection (2003-2006), the framework was stable and that the relative importance of the determinants of confidence was, generally, constant over time. Some changes were observed regarding the mean ratings on the latent constructs. The second study explored how newspaper coverage of food safety related issues affects consumer confidence in the safety of food through subjective consumer recall of food safety incidents. The results show that the newspaper coverage on food safety issues is positively associated with consumer recall of food safety incidents, both in terms of intensity and recency of media coverage.

Optimal PGU operation strategy in CHP systems

NASA Astrophysics Data System (ADS)

Yun, Kyungtae

Traditional power plants only utilize about 30 percent of the primary energy that they consume, and the rest of the energy is usually wasted in the process of generating or transmitting electricity. On-site and near-site power generation has been considered by business, labor, and environmental groups to improve the efficiency and the reliability of power generation. Combined heat and power (CHP) systems are a promising alternative to traditional power plants because of the high efficiency and low CO2 emission achieved by recovering waste thermal energy produced during power generation. A CHP operational algorithm designed to optimize operational costs must be relatively simple to implement in practice such as to minimize the computational requirements from the hardware to be installed. This dissertation focuses on the following aspects pertaining the design of a practical CHP operational algorithm designed to minimize the operational costs: (a) real-time CHP operational strategy using a hierarchical optimization algorithm; (b) analytic solutions for cost-optimal power generation unit operation in CHP Systems; (c) modeling of reciprocating internal combustion engines for power generation and heat recovery; (d) an easy to implement, effective, and reliable hourly building load prediction algorithm.

Program For Engineering Electrical Connections

NASA Technical Reports Server (NTRS)

Billitti, Joseph W.

1990-01-01

DFACS is interactive multiuser computer-aided-engineering software tool for system-level electrical integration and cabling engineering. Purpose of program to provide engineering community with centralized data base for putting in and gaining access to data on functional definition of system, details of end-circuit pinouts in systems and subsystems, and data on wiring harnesses. Objective, to provide instantaneous single point of interchange of information, thus avoiding error-prone, time-consuming, and costly shuttling of data along multiple paths. Designed to operate on DEC VAX mini or micro computer using Version 5.0/03 of INGRES.

Automating security monitoring and analysis for Space Station Freedom's electric power system

NASA Technical Reports Server (NTRS)

Dolce, James L.; Sobajic, Dejan J.; Pao, Yoh-Han

1990-01-01

Operating a large, space power system requires classifying the system's status and analyzing its security. Conventional algorithms are used by terrestrial electric utilities to provide such information to their dispatchers, but their application aboard Space Station Freedom will consume too much processing time. A new approach for monitoring and analysis using adaptive pattern techniques is presented. This approach yields an on-line security monitoring and analysis algorithm that is accurate and fast; and thus, it can free the Space Station Freedom's power control computers for other tasks.

Automating security monitoring and analysis for Space Station Freedom's electric power system

NASA Technical Reports Server (NTRS)

Dolce, James L.; Sobajic, Dejan J.; Pao, Yoh-Han

1990-01-01

Operating a large, space power system requires classifying the system's status and analyzing its security. Conventional algorithms are used by terrestrial electric utilities to provide such information to their dispatchers, but their application aboard Space Station Freedom will consume too much processing time. A novel approach for monitoring and analysis using adaptive pattern techniques is presented. This approach yields an on-line security monitoring and analysis algorithm that is accurate and fast; and thus, it can free the Space Station Freedom's power control computers for other tasks.

Large area sheet task: Advanced Dendritic Web Growth Development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1981-01-01

A melt level control system was implemented to provide stepless silicon feed rates from zero to rates exactly matching the silicon consumed during web growth. Bench tests of the unit were successfully completed and the system mounted in a web furnace for operational verification. Tests of long term temperature drift correction techniques were made; web width monitoring seems most appropriate for feedback purposes. A system to program the initiation of the web growth cycle was successfully tested. A low cost temperature controller was tested which functions as well as units four times as expensive.

The Challenges in Training of the Mechanized Infantry Units of the Republic of Korea Army in Transitioning from the Armored Personnel Carrier (K200) to Infantry Fighting Vehicle (K21)

DTIC Science & Technology

2012-12-14

Technology 2011). Because this paper mainly depends on the case study of the U.S. M2 BFV fielding, the author reviewed a wide variety of literature...defilade position. The dismounted element is also available for the military operations in urban terrain and forest enviroments , and providing...of the technological developments of the BFV, such as the blue force tracking system, it is still very important and requires much time- consuming

Note: Easy-to-maintain electron cyclotron resonance (ECR) plasma sputtering apparatus featuring hybrid waveguide and coaxial cables for microwave delivery

NASA Astrophysics Data System (ADS)

Akazawa, Housei

2016-06-01

The branched-waveguide electron cyclotron resonance plasma sputtering apparatus places quartz windows for transmitting microwaves into the plasma source not in the line of sight of the target. However, the quartz windows must be replaced after some time of operation. For maintenance, the loop waveguide branching from the T-junction must be dismounted and re-assembled accurately, which is a time-consuming job. We investigated substituting the waveguide branches with two sets of coaxial cables and waveguide/coaxial cable converters to simplify assembly as far as connection and disconnection go. The resulting hybrid system worked well for the purposes of plasma generation and film deposition.

Note: Easy-to-maintain electron cyclotron resonance (ECR) plasma sputtering apparatus featuring hybrid waveguide and coaxial cables for microwave delivery.

PubMed

Akazawa, Housei

2016-06-01

The branched-waveguide electron cyclotron resonance plasma sputtering apparatus places quartz windows for transmitting microwaves into the plasma source not in the line of sight of the target. However, the quartz windows must be replaced after some time of operation. For maintenance, the loop waveguide branching from the T-junction must be dismounted and re-assembled accurately, which is a time-consuming job. We investigated substituting the waveguide branches with two sets of coaxial cables and waveguide/coaxial cable converters to simplify assembly as far as connection and disconnection go. The resulting hybrid system worked well for the purposes of plasma generation and film deposition.

Requirements analysis for a hardware, discrete-event, simulation engine accelerator

NASA Astrophysics Data System (ADS)

Taylor, Paul J., Jr.

1991-12-01

An analysis of a general Discrete Event Simulation (DES), executing on the distributed architecture of an eight mode Intel PSC/2 hypercube, was performed. The most time consuming portions of the general DES algorithm were determined to be the functions associated with message passing of required simulation data between processing nodes of the hypercube architecture. A behavioral description, using the IEEE standard VHSIC Hardware Description and Design Language (VHDL), for a general DES hardware accelerator is presented. The behavioral description specifies the operational requirements for a DES coprocessor to augment the hypercube's execution of DES simulations. The DES coprocessor design implements the functions necessary to perform distributed discrete event simulations using a conservative time synchronization protocol.

Evaluating Mobile Graphics Processing Units (GPUs) for Real-Time Resource Constrained Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meredith, J; Conger, J; Liu, Y

2005-11-11

Modern graphics processing units (GPUs) can provide tremendous performance boosts for some applications beyond what a single CPU can accomplish, and their performance is growing at a rate faster than CPUs as well. Mobile GPUs available for laptops have the small form factor and low power requirements suitable for use in embedded processing. We evaluated several desktop and mobile GPUs and CPUs on traditional and non-traditional graphics tasks, as well as on the most time consuming pieces of a full hyperspectral imaging application. Accuracy remained high despite small differences in arithmetic operations like rounding. Performance improvements are summarized here relativemore » to a desktop Pentium 4 CPU.« less

Performance of optical fibers in space radiation environment

NASA Astrophysics Data System (ADS)

Alam, M.; Abramczyk, J.; Manyam, U.; Farroni, J.; Guertin, D.

2017-11-01

The use of optical fibers in low earth orbiting (LEO) satellites is a source of concern due to the radiation environment in which these satellites operate and the reliability of devices based on these fibers. Although radiation induced damage in optical fibers cannot be avoided, it can certainly be minimized by intelligent engineering. Qualifying fibers for use in space is both time consuming and expensive, and manufacturers of satellites and their payloads have started to ask for radiation performance data from optical fiber vendors. Over time, Nufern has developed fiber designs, compositions and processes to make radiation hard fibers. Radiation performance data of a variety of fibers that find application in space radiation environment are presented.

Note: Easy-to-maintain electron cyclotron resonance (ECR) plasma sputtering apparatus featuring hybrid waveguide and coaxial cables for microwave delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akazawa, Housei, E-mail: akazawa.housei@lab.ntt.co.jp

2016-06-15

The branched-waveguide electron cyclotron resonance plasma sputtering apparatus places quartz windows for transmitting microwaves into the plasma source not in the line of sight of the target. However, the quartz windows must be replaced after some time of operation. For maintenance, the loop waveguide branching from the T-junction must be dismounted and re-assembled accurately, which is a time-consuming job. We investigated substituting the waveguide branches with two sets of coaxial cables and waveguide/coaxial cable converters to simplify assembly as far as connection and disconnection go. The resulting hybrid system worked well for the purposes of plasma generation and film deposition.

Consumer-operated service organizations: organizational characteristics, community relationships, and the potential for citizenship.

PubMed

Tanenbaum, Sandra J

2012-08-01

Consumer-operated service organizations (COSOs) are independent organizations whose administrative and financial control resides with consumers. Based on a 2008 mail survey and followup interviews conducted in 2009, this study depicts the internal characteristics and external relationships, as well as some relationships between the two, of COSOs in one state. Profiles include on the one hand, governance structures, services provided, sources and levels of funding, etc. and on the other, relationships between COSOs and other actors in the mental health system and the local community. COSOs emerge as more self-governing and community-based than required by certification requirements and as developing internally and externally in tandem. COSOs are not only adjunct or alternative service providers, but also civic associations and loci for the expression of citizenship by mentally ill people.

77 FR 63799 - Proposed Extension of Approval of Information Collection; Comment Request-Electrically Operated...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-17

...; Comment Request--Electrically Operated Toys and Children's Articles AGENCY: Consumer Product Safety... and children's articles. The collection of information consists of testing and recordkeeping... Operated Articles Intended for Use by Children,'' codified at 16 CFR part 1505. This document was published...

Toward the intelligent use of health care consumer surveys.

PubMed

Allen, H M

1995-01-01

Consumer surveys are at a pivotal moment in health care. With demand for consumer-supplied data escalating in every sector of the industry, current opportunities for consumer surveys to demonstrate unique value in the marketplace are unparalleled. These opportunities, however, carry considerable risks, particularly with respect to performance report cards for competing health plans and providers. As investigators multiply in an area notably lacking in standardization, the chances increase that surveys will arrive at conflicting assessments of plans and providers. To resolve these inconsistencies, users will need to sharpen their understanding of the role of consumer surveys, the business and operational needs they can address, and how their results can be affected by methodology. This article discusses each of these issues with an eye toward promoting intelligent use of consumer surveys in the health care marketplace.

What Is Direct-to-Consumer Genetic Testing?

MedlinePlus

... consumer genetic testing? What is direct-to-consumer genetic testing? Most of the time, genetic testing is ... testing. For more information about direct-to-consumer genetic testing: Centers for Disease Control and Prevention (CDC) ...

Study of the performances of nano-case treatment cutting tools on carbon steel work material during turning operation

NASA Astrophysics Data System (ADS)

Afolalu, S. A.; Okokpujie, I. P.; Salawu, E. Y.; Abioye, A. A.; Abioye, O. P.; Ikumapayi, O. M.

2018-04-01

The degree of holding temperature and time play a major role in nano-case treatment of cutting tools which immensely contributed to its performance during machining operation. The objective of this research work is to carryout comparative study of performance of nano-case treatment tools developed using low and medium carbon steel as work piece. Turning operation was carried out under two different categories with specific work piece on universal lathe machine using HSS cutting tools 100 mm × 12mm × 12mm that has been nano-case treated under varying conditions of temperatures and timeof 800,850, 900, 950°C and 60, 90, 120 mins respectively. The turning parameters used in evaluating this experiment were cutting speed of 270, 380 and 560mm/min, feed rate of 0.15, 0.20 and 0.25 mm/min, depth of cut of 2mm, work piece diameter of 25mm and rake angle of 7° each at three levels. The results of comparative study of their performances revealed that the timespent in the machining of low carbon steel material at a minimum temperature and time of 800°C, 60 mins were1.50, 2.17 mins while at maximum temperature and time of 950°C, 120 mins were 1.19, 2.02 mins. It was also observed that at a corresponding constant speed of 270,380 and 560mm/min at higher temperature and time, a relative increased in the length of cut were observed. Critical observation of the result showed that at higher case hardening temperature and time (950°C/120mins), the HSS cutting tool gave a better performance as lesser time was consumed during the turning operation.

Single Incision Laparoscopic Assisted Appendectomy: Experience of 82 Cases

PubMed Central

Sinha, Anant Narayan; Deepak, Desh; Pandey, NK; Nandani

2016-01-01

Introduction Single Incision Laparoscopic Surgery (SILS) is one of the most recent developments which have been made in the field of minimal assesses surgery. It has potential advantages of less postoperative pain and better cosmesis, but at the same time, this procedure is time consuming and it increases the cost of surgery. Aim In this study, we evaluated the feasibility, safety and potential advantages of single incision laparoscopic assisted appendectomy. Materials and Methods Single incision laparoscopic assisted appendectomy was done in 82 patients who were diagnosed with acute or chronic appendicitis. A single 10mm incision made over right lower quadrant was used for placing two 5mm trocars and appendisectomy was done as in open surgery, after delivering out the appendix from the incision. Results Mean operative time was 32.56 ± 15.5 minutes. Mean post-operative pain scores as per visual analogue scalewere 6.5, 4.2 and 1.2 on 12 hours day 1 and day 2 after surgery respectively. Mean length of hospital stay was 1.4 ± 1.2 days. Conclusion Single incision laparoscopic appendectomy is safe and feasible. PMID:27437295

Non-exposed endoscopic wall-inversion surgery for gastrointestinal stromal tumor

PubMed Central

Mitsui, Takashi; Aikou, Susumu; Niimi, Keiko; Fujishiro, Mitsuhiro; Seto, Yasuyuki

2018-01-01

Laparoscopic and endoscopic cooperative surgery (LECS) is an accepted method of laparoscopic wedge resection, which is minimally invasive, for gastrointestinal stromal tumors (GISTs). We established a type of LECS achieving a full-thickness resection, non-exposed endoscopic wall-inversion surgery (NEWS), in an effort to prevent exposure of the peritoneal cavity to gastric intraluminal contents. We employed this surgical technique in 28 gastric GIST patients. We failed to complete NEWS in the initial two patients and in one patient with a large tumor (40 mm × 35 mm), but otherwise carried out the procedure successfully. Although a learning effect is speculated to occur, based on a decreasing trend in the operation time, the median operation time was 184 minutes showing that NEWS is still a time-consuming method. No significant differences were recognized in tumor size or location, except near the esophagogastric junction (EGJ), nor in the cross-sectional circumference. NEWS is feasible and appears to be a good option, especially for small GISTs with mucosal ulceration rendering full-thickness enucleation by opening of the gastric wall unfeasible. PMID:29682624

Automated Car Park Management System

NASA Astrophysics Data System (ADS)

Fabros, J. P.; Tabañag, D.; Espra, A.; Gerasta, O. J.

2015-06-01

This study aims to develop a prototype for an Automated Car Park Management System that will increase the quality of service of parking lots through the integration of a smart system that assists motorist in finding vacant parking lot. The research was based on implementing an operating system and a monitoring system for parking system without the use of manpower. This will include Parking Guidance and Information System concept which will efficiently assist motorists and ensures the safety of the vehicles and the valuables inside the vehicle. For monitoring, Optical Character Recognition was employed to monitor and put into list all the cars entering the parking area. All parking events in this system are visible via MATLAB GUI which contain time-in, time-out, time consumed information and also the lot number where the car parks. To put into reality, this system has a payment method, and it comes via a coin slot operation to control the exit gate. The Automated Car Park Management System was successfully built by utilizing microcontrollers specifically one PIC18f4550 and two PIC16F84s and one PIC16F628A.

Does a time constraint modify results from rating-based conjoint analysis? Case study with orange/pomegranate juice bottles.

PubMed

Reis, Felipe; Machín, Leandro; Rosenthal, Amauri; Deliza, Rosires; Ares, Gastón

2016-12-01

People do not usually process all the available information on packages for making their food choices and rely on heuristics for making their decisions, particularly when having limited time. However, in most consumer studies encourage participants to invest a lot of time for making their choices. Therefore, imposing a time-constraint in consumer studies may increase their ecological validity. In this context, the aim of the present work was to evaluate the influence of a time-constraint on consumer evaluation of pomegranate/orange juice bottles using rating-based conjoint task. A consumer study with 100 participants was carried out, in which they had to evaluate 16 pomegranate/orange fruit juice bottles, differing in bottle design, front-of-pack nutritional information, nutrition claim and processing claim, and to rate their intention to purchase. Half of the participants evaluated the bottle images without time constraint and the other half had a time-constraint of 3s for evaluating each image. Eye-movements were recorded during the evaluation. Results showed that time-constraint when evaluating intention to purchase did not largely modify the way in which consumers visually processed bottle images. Regardless of the experimental condition (with or without time constraint), they tended to evaluate the same product characteristics and to give them the same relative importance. However, a trend towards a more superficial evaluation of the bottles that skipped complex information was observed. Regarding the influence of product characteristics on consumer intention to purchase, bottle design was the variable with the largest relative importance in both conditions, overriding the influence of nutritional or processing characteristics, which stresses the importance of graphic design in shaping consumer perception. Copyright © 2016 Elsevier Ltd. All rights reserved.

Online total organic carbon (TOC) monitoring for water and wastewater treatment plants processes and operations optimization

NASA Astrophysics Data System (ADS)

Assmann, Céline; Scott, Amanda; Biller, Dondra

2017-08-01

Organic measurements, such as biological oxygen demand (BOD) and chemical oxygen demand (COD) were developed decades ago in order to measure organics in water. Today, these time-consuming measurements are still used as parameters to check the water treatment quality; however, the time required to generate a result, ranging from hours to days, does not allow COD or BOD to be useful process control parameters - see (1) Standard Method 5210 B; 5-day BOD Test, 1997, and (2) ASTM D1252; COD Test, 2012. Online organic carbon monitoring allows for effective process control because results are generated every few minutes. Though it does not replace BOD or COD measurements still required for compliance reporting, it allows for smart, data-driven and rapid decision-making to improve process control and optimization or meet compliances. Thanks to the smart interpretation of generated data and the capability to now take real-time actions, municipal drinking water and wastewater treatment facility operators can positively impact their OPEX (operational expenditure) efficiencies and their capabilities to meet regulatory requirements. This paper describes how three municipal wastewater and drinking water plants gained process insights, and determined optimization opportunities thanks to the implementation of online total organic carbon (TOC) monitoring.

Residential Customer Enrollment in Time-based Rate and Enabling Technology Programs: Smart Grid Investment Grant Consumer Behavior Study Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, Annika; Cappers, Peter; Goldman, Charles

2013-05-01

The U.S. Department of Energy’s (DOE’s) Smart Grid Investment Grant (SGIG) program is working with a subset of the 99 SGIG projects undertaking Consumer Behavior Studies (CBS), which examine the response of mass market consumers (i.e., residential and small commercial customers) to time-varying electricity prices (referred to herein as time-based rate programs) in conjunction with the deployment of advanced metering infrastructure (AMI) and associated technologies. The effort presents an opportunity to advance the electric industry’s understanding of consumer behavior.

77 FR 25168 - Appraisal Subcommittee (ASC); ASC Rules of Operation; Amended

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-27

... heads of the Bureau of Consumer Financial Protection and the Federal Housing Finance Agency. The ASC Rules of Operation serve as corporate bylaws outlining the ASC's purpose, functions, authority... Title XI. The ASC Rules of Operation serve as corporate bylaws outlining the ASC's purpose, functions...

Research-Based Model for Adult Consumer-Homemaking Education.

ERIC Educational Resources Information Center

Ball State Univ., Muncie, IN.

This model is designed to be used as a guide by all teachers and designers of adult vocational consumer and homemaking courses who usually function as program planners. Chapter 1 contains an operational definition, the rationale, and description of intended users. Chapter 2 presents the model description with an overview and discussion of the…

Electronics

DTIC Science & Technology

2001-01-01

International Acer Incorporated, Hsin Chu, Taiwan Aerospace Industrial Development Corporation, Taichung, Taiwan American Institute of Taiwan, Taipei, Taiwan...Singapore and Malaysia .5 - 4 - The largest market for semiconductor products is the high technology consumer electronics industry that consumes up...Singapore, and Malaysia . A new semiconductor facility costs around $3 billion to build and takes about two years to become operational

16 CFR § 1211.13 - Inherent force activated secondary door sensors.

Code of Federal Regulations, 2013 CFR

2013-01-01

... sensors. § 1211.13 Section § 1211.13 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER... Standard § 1211.13 Inherent force activated secondary door sensors. (a) Normal operation test. (1) A force activated door sensor of a door system installed according to the installation instructions shall actuate...

The Role of Consumers in Planning and Evaluation of College Health Programs.

ERIC Educational Resources Information Center

Remer, Robert B.

This report presents the thesis that most college health services will have to undergo critical reexamination and drastic changes before students can rightfully participate as consumers and before effective planning becomes standard operating procedure. The two basic areas where these changes will have to occur are: (1) in consideration and…

Human Health Baseline Risk Assessment for the Estuary, Operable Unit 1, Marsh Trespasser, Fish and Shellfish Consumer, Clapper Rail Consumer, LCP Chemicals Superfund Site

EPA Pesticide Factsheets

report on marsh trespasser and consumption of fish, shellfish, and clapper rail at LCP Superfund site in Brunswick, Georgia, prepared by EPS, Inc. in Aug. 2011. Region ID: 04 DocID: 10841008, DocDate: 08-01-2011

Requirements for Planetary Outpost Life-Support Systems and the Possible Use of In Situ Resources

NASA Technical Reports Server (NTRS)

Gruener, John E.; Ming, D. W.

1998-01-01

If humans are ever to live and work on the Moon or Mars for extended periods of time, the operation of regenerative life-support systems at the planetary outposts will be a critical requirement. The substantial amount of materials consumed by humans and the inevitable waste products make open-loop life-support systems and resupply missions (as used in Space Shuttle and Mir operations) impractical and expensive. Natural resources found on the Moon and Mars could be used in conjunction with regenerative life support systems to further reduce the amount of material that would need to be delivered from Earth. There have been numerous studies and experiments conducted on the production of O from regolith materials on the Moon and from the atmosphere of Mars. One or several of these processes could undoubtedly be used to produce the O required by the crews at planetary outposts. Water is required in the greatest quantities, primarily for tasks such as personal hygiene and clothes washing, and it will be the most precious consumable. Again, several process have been described to produce water on the Moon using solar-wind implanted H and O, and if water ice can be found and mined at the lunar poles, another source of water may be available.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawrence, Thomas M.; Boudreau, Marie-Claude; Helsen, Lieve

Recent advances in information and communications technology (ICT) have initiated development of a smart electrical grid and smart buildings. Buildings consume a large portion of the total electricity production worldwide, and to fully develop a smart grid they must be integrated with that grid. Buildings can now be 'prosumers' on the grid (both producers and consumers), and the continued growth of distributed renewable energy generation is raising new challenges in terms of grid stability over various time scales. Buildings can contribute to grid stability by managing their overall electrical demand in response to current conditions. Facility managers must balance demandmore » response requests by grid operators with energy needed to maintain smooth building operations. For example, maintaining thermal comfort within an occupied building requires energy and, thus an optimized solution balancing energy use with indoor environmental quality (adequate thermal comfort, lighting, etc.) is needed. Successful integration of buildings and their systems with the grid also requires interoperable data exchange. However, the adoption and integration of newer control and communication technologies into buildings can be problematic with older legacy HVAC and building control systems. Public policy and economic structures have not kept up with the technical developments that have given rise to the budding smart grid, and further developments are needed in both technical and non-technical areas.« less

Acousto-optic time- and space-integrating spotlight-mode SAR processor

NASA Astrophysics Data System (ADS)

Haney, Michael W.; Levy, James J.; Michael, Robert R., Jr.

1993-09-01

The technical approach and recent experimental results for the acousto-optic time- and space- integrating real-time SAR image formation processor program are reported. The concept overcomes the size and power consumption limitations of electronic approaches by using compact, rugged, and low-power analog optical signal processing techniques for the most computationally taxing portions of the SAR imaging problem. Flexibility and performance are maintained by the use of digital electronics for the critical low-complexity filter generation and output image processing functions. The results include a demonstration of the processor's ability to perform high-resolution spotlight-mode SAR imaging by simultaneously compensating for range migration and range/azimuth coupling in the analog optical domain, thereby avoiding a highly power-consuming digital interpolation or reformatting operation usually required in all-electronic approaches.

Determining the market value of high-rise residential buildings based on evaluation of consumer properties

NASA Astrophysics Data System (ADS)

Kolobova, Svetlana

2018-03-01

As you know, high-rise construction is an indicator of the practical implementation of advanced innovative technologies in the construction industry of the country. High-rise building inevitably comes to the big cities, in connection with the shortage and value of land. The life cycle of any construction project, including high-rise buildings consists of chains: of engineering survey - design-construction-operation. In the process of operation of a tall building, decisions about major repairs or reconstruction of a building are made for decision-making on further use. This article describes methods of assessing the consumer quality of high-rise residential buildings and the establishment of prices based on consumer characteristics of a tall residential building. It is proposed to assess the premises under their quality characteristics. The study was conducted to establish the influence of individual, comprehensive and integral indicators of comparable quality for effective quality living spaces. Simultaneously, there was established a relationship of quality with the consumer cost of housing, ultimately with the potential needs of owners, tenants of the home, lessor dwelling, or buyers of residential properties and other participants in the residential real estate market. This relationship further creates consumer requirements to quality standard of premises at a certain stage of socio-economic development.

Autonomously Generating Operations Sequences for a Mars Rover Using Artificial Intelligence-Based Planning

NASA Astrophysics Data System (ADS)

Sherwood, R.; Mutz, D.; Estlin, T.; Chien, S.; Backes, P.; Norris, J.; Tran, D.; Cooper, B.; Rabideau, G.; Mishkin, A.; Maxwell, S.

2001-07-01

This article discusses a proof-of-concept prototype for ground-based automatic generation of validated rover command sequences from high-level science and engineering activities. This prototype is based on ASPEN, the Automated Scheduling and Planning Environment. This artificial intelligence (AI)-based planning and scheduling system will automatically generate a command sequence that will execute within resource constraints and satisfy flight rules. An automated planning and scheduling system encodes rover design knowledge and uses search and reasoning techniques to automatically generate low-level command sequences while respecting rover operability constraints, science and engineering preferences, environmental predictions, and also adhering to hard temporal constraints. This prototype planning system has been field-tested using the Rocky 7 rover at JPL and will be field-tested on more complex rovers to prove its effectiveness before transferring the technology to flight operations for an upcoming NASA mission. Enabling goal-driven commanding of planetary rovers greatly reduces the requirements for highly skilled rover engineering personnel. This in turn greatly reduces mission operations costs. In addition, goal-driven commanding permits a faster response to changes in rover state (e.g., faults) or science discoveries by removing the time-consuming manual sequence validation process, allowing rapid "what-if" analyses, and thus reducing overall cycle times.

IMIS: An intelligence microscope imaging system

NASA Technical Reports Server (NTRS)

Caputo, Michael; Hunter, Norwood; Taylor, Gerald

1994-01-01

Until recently microscope users in space relied on traditional microscopy techniques that required manual operation of the microscope and recording of observations in the form of written notes, drawings, or photographs. This method was time consuming and required the return of film and drawings from space for analysis. No real-time data analysis was possible. Advances in digital and video technologies along with recent developments in article intelligence will allow future space microscopists to have a choice of three additional modes of microscopy: remote coaching, remote control, and automation. Remote coaching requires manual operations of the microscope with instructions given by two-way audio/video transmission during critical phases of the experiment. When using the remote mode of microscopy, the Principal Investigator controls the microscope from the ground. The automated mode employs artificial intelligence to control microscope functions and is the only mode that can be operated in the other three modes as well. The purpose of this presentation is to discuss the advantages and disadvantages of the four modes of of microscopy and how the IMIS, a proposed intelligent microscope imaging system, can be used as a model for developing and testing concepts, operating procedures, and equipment design of specifications required to provide a comprehensive microscopy/imaging capability onboard Space Station Freedom.

[Cost analysis for navigation in knee endoprosthetics].

PubMed

Cerha, O; Kirschner, S; Günther, K-P; Lützner, J

2009-12-01

Total knee arthroplasty (TKA) is one of the most frequent procedures in orthopaedic surgery. The outcome depends on a range of factors including alignment of the leg and the positioning of the implant in addition to patient-associated factors. Computer-assisted navigation systems can improve the restoration of a neutral leg alignment. This procedure has been established especially in Europe and North America. The additional expenses are not reimbursed in the German DRG system (Diagnosis Related Groups). In the present study a cost analysis of computer-assisted TKA compared to the conventional technique was performed. The acquisition expenses of various navigation systems (5 and 10 year depreciation), annual costs for maintenance and software updates as well as the accompanying costs per operation (consumables, additional operating time) were considered. The additional operating time was determined on the basis of a meta-analysis according to the current literature. Situations with 25, 50, 100, 200 and 500 computer-assisted TKAs per year were simulated. The amount of the incremental costs of the computer-assisted TKA depends mainly on the annual volume and the additional operating time. A relevant decrease of the incremental costs was detected between 50 and 100 procedures per year. In a model with 100 computer-assisted TKAs per year an additional operating time of 14 mins and a 10 year depreciation of the investment costs, the incremental expenses amount to 300-395 depending on the navigation system. Computer-assisted TKA is associated with additional costs. From an economical point of view an amount of more than 50 procedures per year appears to be favourable. The cost-effectiveness could be estimated if long-term results will show a reduction of revisions or a better clinical outcome.

SciBox, an end-to-end automated science planning and commanding system

NASA Astrophysics Data System (ADS)

Choo, Teck H.; Murchie, Scott L.; Bedini, Peter D.; Steele, R. Josh; Skura, Joseph P.; Nguyen, Lillian; Nair, Hari; Lucks, Michael; Berman, Alice F.; McGovern, James A.; Turner, F. Scott

2014-01-01

SciBox is a new technology for planning and commanding science operations for Earth-orbital and planetary space missions. It has been incrementally developed since 2001 and demonstrated on several spaceflight projects. The technology has matured to the point that it is now being used to plan and command all orbital science operations for the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) mission to Mercury. SciBox encompasses the derivation of observing sequences from science objectives, the scheduling of those sequences, the generation of spacecraft and instrument commands, and the validation of those commands prior to uploading to the spacecraft. Although the process is automated, science and observing requirements are incorporated at each step by a series of rules and parameters to optimize observing opportunities, which are tested and validated through simulation and review. Except for limited special operations and tests, there is no manual scheduling of observations or construction of command sequences. SciBox reduces the lead time for operations planning by shortening the time-consuming coordination process, reduces cost by automating the labor-intensive processes of human-in-the-loop adjudication of observing priorities, reduces operations risk by systematically checking constraints, and maximizes science return by fully evaluating the trade space of observing opportunities to meet MESSENGER science priorities within spacecraft recorder, downlink, scheduling, and orbital-geometry constraints.

Microfluidics-Based Lab-on-Chip Systems in DNA-Based Biosensing: An Overview

PubMed Central

Dutse, Sabo Wada; Yusof, Nor Azah

2011-01-01

Microfluidics-based lab-on-chip (LOC) systems are an active research area that is revolutionising high-throughput sequencing for the fast, sensitive and accurate detection of a variety of pathogens. LOCs also serve as portable diagnostic tools. The devices provide optimum control of nanolitre volumes of fluids and integrate various bioassay operations that allow the devices to rapidly sense pathogenic threat agents for environmental monitoring. LOC systems, such as microfluidic biochips, offer advantages compared to conventional identification procedures that are tedious, expensive and time consuming. This paper aims to provide a broad overview of the need for devices that are easy to operate, sensitive, fast, portable and sufficiently reliable to be used as complementary tools for the control of pathogenic agents that damage the environment. PMID:22163925

Single shot demountable self-contained He-3 refrigerator

NASA Technical Reports Server (NTRS)

Kittel, P.; Brooks, W. F.

1982-01-01

The present investigation is concerned with the development of a self-contained demountable He-3 refrigerator which greatly increases the versatility of a cold-plate-style helium Dewar. The refrigerator is controlled by a single heater. The considered design makes it possible to achieve a temperature of 0.27 K without costly or time-consuming modifications to the Dewar. An example for an employment of a temperature of less than 1 K in space is related to the study of the critical behavior of He-3/He-4 mixtures in the absence of gravitational mixing. This requires a temperature of 0.87 K. Such low temperatures can also be utilized in the space operation of infrared telescopes. Attention is given to details of system design, the operating principles, and aspects of performance.

Orbital Spacecraft Consumables Resupply System (OSCRS). Volume 3: Program Cost Estimate

NASA Technical Reports Server (NTRS)

Perry, D. L.

1986-01-01

A cost analysis for the design, development, qualification, and production of the monopropellant and bipropellant Orbital Spacecraft Consumable Resupply System (OSCRS) tankers, their associated avionics located in the Orbiter payload bay, and the unique ground support equipment (GSE) and airborne support equipment (ASE) required to support operations is presented. Monopropellant resupply for the Gamma Ray Observatory (GRO) in calendar year 1991 is the first defined resupply mission with bipropellant resupply missions expected in the early to mid 1990's. The monopropellant program estimate also includes contractor costs associated with operations support through the first GRO resupply mission.

The integrated feasibility analysis of water reuse management in the petroleum exploration performances of unconventional shale reservoirs

NASA Astrophysics Data System (ADS)

Davarpanah, Afshin

2018-05-01

Regarding the dramatic increase of water additional resource administration in numerous drilling industries' operational performances and oil/gas extractions, water supply plays a significant role in their performances as efficient as optimum operations, in respect of the way, this utilization is often invisible to the public eye. The necessity of water in a wide variety of drilling operation due to its vast applicant in several functions is widely reported in the literature that has been required to remain these procedures plateau. The objective of this comprehensive study is to conduct an investigation into the studied field and analyze the assessment of necessary water and produced water which is provided in the surface for reinjection procedures in the hydraulic fracturing and water injectivity; in respect of the way, petroleum and drilling industries will push themselves into limits to find suitable water sources from a local source to encapsulate their economic prosperities and virtually eliminate extra expenditures. In comparison to other industries and consumers, oil and gas development is not a significant water consumer, and its water demands can exert profound impacts on local water resources, and this is why it imposes particular challenges among water users in a vast majority of fields and areas in times of drought. Moreover, water has become an increasingly scarce and costly commodity over the past decades, and operators are being beneficially noted that awareness of recycling and reusing phenomenon that has treated effluent is both costs competent and socially responsible. Consequently, energy, environmental situation, and economic prosperity considerations should be analytically and preferably investigated to cover every eventuality and each possibility of disposal and water reuse options.

Anticipatory Consumer Socialization.

ERIC Educational Resources Information Center

Moore, Roy L.; Moschis, George P.

Anticipatory consumer socialization is the learning of consumer roles and perceptions, which will be assumed at a later time, such as those that children acquire before they become adult consumers. A survey of 784 adolescents was conducted in a southern state to examine the anticipatory consumer socialization effects of such factors as the mass…

An investigation of used electronics return flows: a data-driven approach to capture and predict consumers storage and utilization behavior.

PubMed

Sabbaghi, Mostafa; Esmaeilian, Behzad; Raihanian Mashhadi, Ardeshir; Behdad, Sara; Cade, Willie

2015-02-01

Consumers often have a tendency to store their used, old or un-functional electronics for a period of time before they discard them and return them back to the waste stream. This behavior increases the obsolescence rate of used still-functional products leading to lower profitability that could be resulted out of End-of-Use (EOU) treatments such as reuse, upgrade, and refurbishment. These types of behaviors are influenced by several product and consumer-related factors such as consumers' traits and lifestyles, technology evolution, product design features, product market value, and pro-environmental stimuli. Better understanding of different groups of consumers, their utilization and storage behavior and the connection of these behaviors with product design features helps Original Equipment Manufacturers (OEMs) and recycling and recovery industry to better overcome the challenges resulting from the undesirable storage of used products. This paper aims at providing insightful statistical analysis of Electronic Waste (e-waste) dynamic nature by studying the effects of design characteristics, brand and consumer type on the electronics usage time and end of use time-in-storage. A database consisting of 10,063 Hard Disk Drives (HDD) of used personal computers returned back to a remanufacturing facility located in Chicago, IL, USA during 2011-2013 has been selected as the base for this study. The results show that commercial consumers have stored computers more than household consumers regardless of brand and capacity factors. Moreover, a heterogeneous storage behavior is observed for different brands of HDDs regardless of capacity and consumer type factors. Finally, the storage behavior trends are projected for short-time forecasting and the storage times are precisely predicted by applying machine learning methods. Copyright © 2014 Elsevier Ltd. All rights reserved.

Laparoendoscopic single site (LESS) cholecystectomy.

PubMed

Hodgett, Steven E; Hernandez, Jonathan M; Morton, Connor A; Ross, Sharona B; Albrink, Michael; Rosemurgy, Alexander S

2009-02-01

The journey from conventional "open" operations to truly "minimally invasive" operations naturally includes progression from operations involving multiple trocars and multiple incisions to operations involving access through the umbilicus alone. Laparoscopic operations through the umbilicus alone, laparoendoscopic single site surgery (LESS), offer improved cosmesis and hopes for less pain and improved recovery. This study was undertaken to evaluate our initial experience with LESS cholecystectomy and to compare our initial experience to concurrent outcomes with more conventional multiport, multi-incision laparoscopic cholecystectomy. All patients referred for cholecystectomy over a 6-month period were offered LESS. Outcomes, including blood loss, operative time, complications, and length of stay were recorded. Outcomes with our first LESS cholecystectomies were compared to an uncontrolled group of concurrent patients undergoing multiport, multi-incision laparoscopic cholecystectomy at the same hospital by the same surgeon. Twenty-nine patients of median age 50 years undergoing LESS cholecystectomy from November 2007 until May 2008 were compared to 29* patients, median age 48 years, undergoing standard multiport, multiple-incision laparoscopic cholecystectomy over the same time period. Median operative time for patients undergoing LESS cholecystectomy was 72 min and was not different from that of patients undergoing multiport, multi-incision laparoscopic cholecystectomy (p = 0.81). Median length of hospital stay was 1.0 day for patients undergoing LESS cholecystectomy and was not different from patients undergoing standard laparoscopic cholecystectomy (p = 0.46). Operative estimated blood loss was less than 100 cc for all patients. No patients undergoing attempted LESS cholecystectomy had conversions to "open" operations; two patients had an additional trocar(s) placed distant from the umbilicus to aid in exposure. Three patients undergoing LESS cholecystectomy had complications: two were troubled by pain control and another had urinary retention. LESS cholecystectomy is a safe and effective alternative to standard laparoscopic cholecystectomy. It can be undertaken without the expense of added operative time and provides patients with minimal, if any, apparent scarring. We believe LESS cholecystectomy will be driven by consumer demand, and therefore, laparoscopic surgeons will need to become proficient with LESS procedures.

Simscape Modeling Verification in the Simulink Development Environment

NASA Technical Reports Server (NTRS)

Volle, Christopher E. E.

2014-01-01

The purpose of the Simulation Product Group of the Control and Data Systems division of the NASA Engineering branch at Kennedy Space Center is to provide a realtime model and simulation of the Ground Subsystems participating in vehicle launching activities. The simulation software is part of the Spaceport Command and Control System (SCCS) and is designed to support integrated launch operation software verification, and console operator training. Using Mathworks Simulink tools, modeling engineers currently build models from the custom-built blocks to accurately represent ground hardware. This is time consuming and costly due to required rigorous testing and peer reviews to be conducted for each custom-built block. Using Mathworks Simscape tools, modeling time can be reduced since there would be no custom-code developed. After careful research, the group came to the conclusion it is feasible to use Simscape's blocks in MatLab's Simulink. My project this fall was to verify the accuracy of the Crew Access Arm model developed using Simscape tools running in the Simulink development environment.

Automatic-heuristic and executive-analytic processing during reasoning: Chronometric and dual-task considerations.

PubMed

De Neys, Wim

2006-06-01

Human reasoning has been shown to overly rely on intuitive, heuristic processing instead of a more demanding analytic inference process. Four experiments tested the central claim of current dual-process theories that analytic operations involve time-consuming executive processing whereas the heuristic system would operate automatically. Participants solved conjunction fallacy problems and indicative and deontic selection tasks. Experiment 1 established that making correct analytic inferences demanded more processing time than did making heuristic inferences. Experiment 2 showed that burdening the executive resources with an attention-demanding secondary task decreased correct, analytic responding and boosted the rate of conjunction fallacies and indicative matching card selections. Results were replicated in Experiments 3 and 4 with a different secondary-task procedure. Involvement of executive resources for the deontic selection task was less clear. Findings validate basic processing assumptions of the dual-process framework and complete the correlational research programme of K. E. Stanovich and R. F. West (2000).

Interfaces detection after corneal refractive surgery by low coherence optical interferometry

PubMed Central

Verrier, I.; Veillas, C.; Lépine, T.; Nguyen, F.; Thuret, G.; Gain, P.

2010-01-01

The detection of refractive corneal surgery by LASIK, during the storage of corneas in Eye Banks will become a challenge when the numerous operated patients will arrive at the age of cornea donation. The subtle changes of corneal structure and refraction are highly suspected to negatively influence clinical results in recipients of such corneas. In order to detect LASIK cornea interfaces we developed a low coherence interferometry technique using a broadband continuum source. Real time signal recording, without moving any optical elements and without need of a Fourier Transform operation, combined with good measurement resolution is the main asset of this interferometer. The associated numerical processing is based on a method initially used in astronomy and offers an optimal correlation signal without the necessity to image the whole cornea that is time consuming. The detection of corneal interfaces - both outer and inner surface and the buried interface corresponding to the surgical wound – is then achieved directly by the innovative combination of interferometry and this original numerical process. PMID:21258562

Microbial fuel cell as power supply for implantable medical devices: a novel configuration design for simulating colonic environment.

PubMed

Dong, Kun; Jia, Boyang; Yu, Chaoling; Dong, Wenbo; Du, Fangzhou; Liu, Hong

2013-03-15

This study focused on providing power for implantable medical devices (IMDs) using a microbial fuel cell (MFC) implanted in human transverse colon. Considering the condition of colonic environment, a continuous-flow single-chamber MFC without membrane was set up. The performance of the MFC was investigated. The power output of 1.6 mW under the steady state was not rich enough for some high energy-consuming IMDs. Moreover, the parameters of the simulated colonic environment, such as pH and ORP value, varied along with the time. Hence, a new MFC configuration was developed. In this novel model, pH transducers were placed in cathodic and anodic areas, so as to regulate the reactor operation timely via external intervention. And two ORP transducers were inserted next to the pH transducers, for monitoring and adjusting the MFC operation efficiently. Besides, colonic haustra were designed in order to increase the difference between cathodic and anodic areas. Copyright © 2012 Elsevier B.V. All rights reserved.

ATTDES: An Expert System for Satellite Attitude Determination and Control. 2

NASA Technical Reports Server (NTRS)

Mackison, Donald L.; Gifford, Kevin

1996-01-01

The design, analysis, and flight operations of satellite attitude determintion and attitude control systems require extensive mathematical formulations, optimization studies, and computer simulation. This is best done by an analyst with extensive education and experience. The development of programs such as ATTDES permit the use of advanced techniques by those with less experience. Typical tasks include the mission analysis to select stabilization and damping schemes, attitude determination sensors and algorithms, and control system designs to meet program requirements. ATTDES is a system that includes all of these activities, including high fidelity orbit environment models that can be used for preliminary analysis, parameter selection, stabilization schemes, the development of estimators covariance analyses, and optimization, and can support ongoing orbit activities. The modification of existing simulations to model new configurations for these purposes can be an expensive, time consuming activity that becomes a pacing item in the development and operation of such new systems. The use of an integrated tool such as ATTDES significantly reduces the effort and time required for these tasks.

Improving Overall Equipment Effectiveness Using CPM and MOST: A Case Study of an Indonesian Pharmaceutical Company

NASA Astrophysics Data System (ADS)

Omega, Dousmaris; Andika, Aditya

2017-12-01

This paper discusses the results of a research conducted on the production process of an Indonesian pharmaceutical company. The company is experiencing low performance in the Overall Equipment Effectiveness (OEE) metric. The OEE of the company machines are below world class standard. The machine that has the lowest OEE is the filler machine. Through observation and analysis, it is found that the cleaning process of the filler machine consumes significant amount of time. The long duration of the cleaning process happens because there is no structured division of jobs between cleaning operators, differences in operators’ ability, and operators’ inability in utilizing available cleaning equipment. The company needs to improve the cleaning process. Therefore, Critical Path Method (CPM) analysis is conducted to find out what activities are critical in order to shorten and simplify the cleaning process in the division of tasks. Afterwards, The Maynard Operation and Sequence Technique (MOST) method is used to reduce ineffective movement and specify the cleaning process standard time. From CPM and MOST, it is obtained the shortest time of the cleaning process is 1 hour 28 minutes and the standard time is 1 hour 38.826 minutes.

A real-time visual inspection method of fastening bolts in freight car operation

NASA Astrophysics Data System (ADS)

Nan, Guo; Yao, JunEn

2015-10-01

A real-time inspection of the key components is necessary for ensuring safe operation of freight car. While traditional inspection depends on the trained human inspectors, which is time-consuming and lower efficient. With the development of machine vision, vision-based inspection methods get more railway on-spot applications. The cross rod end fastening bolts are important components on both sides of the train body that fixing locking plates together with the freight car main structure. In our experiment, we get the images containing fastening bolt components, and accurately locate the locking plate position using a linear Support Vector Machine (SVM) locating model trained with Histograms of Oriented Gradients (HOG) features. Then we extract the straight line segment using the Line Segment Detector (LSD) and encoding them in a range, which constitute a straight line segment dataset. Lastly we determine the locking plate's working state by the linear pattern. The experiment result shows that the localization accurate rate is over 99%, the fault detection rate is over 95%, and the module implementation time is 2f/s. The overall performance can completely meet the practical railway safety assurance application.

Traditional and online consumers in China: a preliminary study of their personality traits and decision-making styles.

PubMed

Zhu, Junpeng; Xu, You; Huang, Jingyi; Yeow, Changdar; Wang, Wei

2012-12-01

Population of online consumers increases rapidly, but the decision-making styles of online consumers and psychiatric denominators such as the personality correlates remain unclear. In 196 traditional, and 196 age-, education- and gender-matched online consumers, we have tested the Zuckerman-Kuhlman Personality Questionnaire (ZKPQ) and the Consumer Style Inventory (CSI). After exploratory and confirmatory factor analyses, we have defined a five-factor model CSI with 24 items. Online consumers scored lower on ZKPQ Neuroticism-Anxiety and higher on Aggression-Hostility than traditional ones did, and scored higher on CSI Novelty-fashion consciousness and Brand consciousness, and lower on Time consciousness than the traditional consumers did. ZKPQ Neuroticism-Anxiety was positively correlated with CSI Confused by overchoice in both groups, Sociability was positively correlated with Novelty-fashion consciousness and negatively with Time consciousness in traditional group, and Impulsive Sensation Seeking was positively correlated with Novelty-fashion consciousness and Time consciousness in online group. Our study suggests that, regarding the decision-making styles, online consumers display curiosity that lacks security and need other ways to improve their social lives. It also calls further designs to address the contributions of other psychiatric features to the particular decision-making styles in online consumers.

Towards an automated intelligence product generation capability

NASA Astrophysics Data System (ADS)

Smith, Alison M.; Hawes, Timothy W.; Nolan, James J.

2015-05-01

Creating intelligence information products is a time consuming and difficult process for analysts faced with identifying key pieces of information relevant to a complex set of information requirements. Complicating matters, these key pieces of information exist in multiple modalities scattered across data stores, buried in huge volumes of data. This results in the current predicament analysts find themselves; information retrieval and management consumes huge amounts of time that could be better spent performing analysis. The persistent growth in data accumulation rates will only increase the amount of time spent on these tasks without a significant advance in automated solutions for information product generation. We present a product generation tool, Automated PrOduct Generation and Enrichment (APOGEE), which aims to automate the information product creation process in order to shift the bulk of the analysts' effort from data discovery and management to analysis. APOGEE discovers relevant text, imagery, video, and audio for inclusion in information products using semantic and statistical models of unstructured content. APOGEEs mixed-initiative interface, supported by highly responsive backend mechanisms, allows analysts to dynamically control the product generation process ensuring a maximally relevant result. The combination of these capabilities results in significant reductions in the time it takes analysts to produce information products while helping to increase the overall coverage. Through evaluation with a domain expert, APOGEE has been shown the potential to cut down the time for product generation by 20x. The result is a flexible end-to-end system that can be rapidly deployed in new operational settings.

Ex vivo applications of multiphoton microscopy in urology

NASA Astrophysics Data System (ADS)

Jain, Manu; Mukherjee, Sushmita

2016-03-01

Background: Routine urological surgery frequently requires rapid on-site histopathological tissue evaluation either during biopsy or intra-operative procedure. However, resected tissue needs to undergo processing, which is not only time consuming but may also create artifacts hindering real-time tissue assessment. Likewise, pathologist often relies on several ancillary methods, in addition to H&E to arrive at a definitive diagnosis. Although, helpful these techniques are tedious and time consuming and often show overlapping results. Therefore, there is a need for an imaging tool that can rapidly assess tissue in real-time at cellular level. Multiphoton microscopy (MPM) is one such technique that can generate histology-quality images from fresh and fixed tissue solely based on their intrinsic autofluorescence emission, without the need for tissue processing or staining. Design: Fresh tissue sections (neoplastic and non-neoplastic) from biopsy and surgical specimens of bladder and kidney were obtained. Unstained deparaffinized slides from biopsy of medical kidney disease and oncocytic renal neoplasms were also obtained. MPM images were acquired using with an Olympus FluoView FV1000MPE system. After imaging, fresh tissues were submitted for routine histopathology. Results: Based on the architectural and cellular details of the tissue, MPM could characterize normal components of bladder and kidney. Neoplastic tissue could be differentiated from non-neoplastic tissue and could be further classified as per histopathological convention. Some of the tumors had unique MPM signatures not otherwise seen on H&E sections. Various subtypes of glomerular lesions were identified as well as renal oncocytic neoplasms were differentiated on unstained deparaffinized slides. Conclusions: We envision MPM to become an integral part of regular diagnostic workflow for rapid assessment of tissue. MPM can be used to evaluate the adequacy of biopsies and triage tissues for ancillary studies. It can also be used as an adjunct to frozen section analysis for intra-operative margin assessment. Further, it can play an important role for pathologist for guiding specimen grossing, selecting tissue for tumor banking and as a rapid ancillary diagnostic tool.

Consumers as mental health providers: first-person accounts of benefits and limitations.

PubMed

Mowbray, C T; Moxley, D P; Collins, M E

1998-11-01

Community support programs are increasingly establishing paid service positions designated exclusively for consumers. Project WINS (Work Incentives and Needs Study), a hybrid case management-vocational program for individuals with severe mental illness, used consumers as peer support specialists (PSSs) to supplement professional roles. Semistructured interviews were conducted with PSSs about 12 months after their employment ended. They identified substantial personal benefits specific to consumer-designated roles (e.g., a "safe" employment setting with accommodations) and general benefits from employment. Problems described were just as numerous, encompassing attitudes toward assigned peers and costs to their own well-being. Critical commentary addressed program operations (structure, supervision, and training needs) and problems in the mental health system. The authors discuss the changed sense of self that service provider roles can create for consumers and suggest that mental health administrators provide anticipatory socialization for this service innovation throughout their agencies and ongoing supports for consumers in their new roles.

Expert system for on-board satellite scheduling and control

NASA Technical Reports Server (NTRS)

Barry, John M.; Sary, Charisse

1988-01-01

An Expert System is described which Rockwell Satellite and Space Electronics Division (S&SED) is developing to dynamically schedule the allocation of on-board satellite resources and activities. This expert system is the Satellite Controller. The resources to be scheduled include power, propellant and recording tape. The activities controlled include scheduling satellite functions such as sensor checkout and operation. The scheduling of these resources and activities is presently a labor intensive and time consuming ground operations task. Developing a schedule requires extensive knowledge of the system and subsystems operations, operational constraints, and satellite design and configuration. This scheduling process requires highly trained experts anywhere from several hours to several weeks to accomplish. The process is done through brute force, that is examining cryptic mnemonic data off line to interpret the health and status of the satellite. Then schedules are formulated either as the result of practical operator experience or heuristics - that is rules of thumb. Orbital operations must become more productive in the future to reduce life cycle costs and decrease dependence on ground control. This reduction is required to increase autonomy and survivability of future systems. The design of future satellites require that the scheduling function be transferred from ground to on board systems.

Large deep neural networks for MS lesion segmentation

NASA Astrophysics Data System (ADS)

Prieto, Juan C.; Cavallari, Michele; Palotai, Miklos; Morales Pinzon, Alfredo; Egorova, Svetlana; Styner, Martin; Guttmann, Charles R. G.

2017-02-01

Multiple sclerosis (MS) is a multi-factorial autoimmune disorder, characterized by spatial and temporal dissemination of brain lesions that are visible in T2-weighted and Proton Density (PD) MRI. Assessment of lesion burden and is useful for monitoring the course of the disease, and assessing correlates of clinical outcomes. Although there are established semi-automated methods to measure lesion volume, most of them require human interaction and editing, which are time consuming and limits the ability to analyze large sets of data with high accuracy. The primary objective of this work is to improve existing segmentation algorithms and accelerate the time consuming operation of identifying and validating MS lesions. In this paper, a Deep Neural Network for MS Lesion Segmentation is implemented. The MS lesion samples are extracted from the Partners Comprehensive Longitudinal Investigation of Multiple Sclerosis (CLIMB) study. A set of 900 subjects with T2, PD and a manually corrected label map images were used to train a Deep Neural Network and identify MS lesions. Initial tests using this network achieved a 90% accuracy rate. A secondary goal was to enable this data repository for big data analysis by using this algorithm to segment the remaining cases available in the CLIMB repository.

Infrared sensor-based aerosol sanitization system for controlling Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes on fresh produce.

PubMed

Kim, Sang-Oh; Ha, Jae-Won; Park, Ki-Hwan; Chung, Myung-Sub; Kang, Dong-Hyun

2014-06-01

An economical aerosol sanitization system was developed based on sensor technology for minimizing sanitizer usage, while maintaining bactericidal efficacy. Aerosol intensity in a system chamber was controlled by a position-sensitive device and its infrared value range. The effectiveness of the infrared sensor-based aerosolization (ISA) system to inactivate Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes on spinach leaf surfaces was compared with conventional aerosolization (full-time aerosol treated), and the amount of sanitizer consumed was determined after operation. Three pathogens artificially inoculated onto spinach leaf surfaces were treated with aerosolized peracetic acid (400 ppm) for 15, 30, 45, and 60 min at room temperature (22 ± 2°C). Using the ISA system, inactivation levels of the three pathogens were equal or better than treatment with conventional full-time aerosolization. However, the amount of sanitizer consumed was reduced by ca. 40% using the ISA system. The results of this study suggest that an aerosol sanitization system combined with infrared sensor technology could be used for transportation and storage of fresh produce efficiently and economically as a practical commercial intervention.

Failure Mode and Effects Analysis: views of hospital staff in the UK.

PubMed

Shebl, Nada; Franklin, Bryony; Barber, Nick; Burnett, Susan; Parand, Anam

2012-01-01

To explore health care professionals' experiences and perceptions of Failure Mode and Effects Analysis (FMEA), a team-based, prospective risk analysis technique. Semi-structured interviews were conducted with 21 operational leads (20 pharmacists, one nurse) in medicines management teams of hospitals participating in a national quality improvement programme. Interviews were transcribed, coded and emergent themes identified using framework analysis. Themes identified included perceptions and experiences of participants with FMEA, validity and reliability issues, and FMEA's use in practice. FMEA was considered to be a structured but subjective process that helps health care professionals get together to identify high risk areas of care. Both positive and negative opinions were expressed, with the majority of interviewees expressing positive views towards FMEA in relation to its structured nature and the use of a multidisciplinary team. Other participants criticised FMEA for being subjective and lacking validity. Most likely to restrict its widespread use were its time consuming nature and its perceived lack of validity and reliability. FMEA is a subjective but systematic tool that helps identify high risk areas, but its time consuming nature, difficulty with the scores and perceived lack of validity and reliability may limit its widespread use.

Solar electric and thermal conversion system in close proximity to the consumer. [solar panels on house roofs

NASA Technical Reports Server (NTRS)

Boeer, K. W.

1975-01-01

Solar cells may be used to convert sunlight directly into electrical energy and into lowgrade heat to be used for large-scale terrestrial solar-energy conversion. Both forms of energy can be utilized if such cells are deployed in close proximity to the consumer (rooftop). Cadmium-sulfide/copper-sulfide (CdS/Cu2S) solar cells are an example of cells which may be produced inexpensively enough to become economically attractive. Cell parameters relevant for combined solar conversion are presented. Critical issues, such as production yield, life expectancy, and stability of performance, are discussed. Systems-design parameters related to operating temperatures are analyzed. First results obtained on Solar One, the experimental house of the University of Delaware, are given. Economic aspects are discussed. Different modes of operation are discussed in respect to the power utility and consumer incentives.

Mental health consumer-operated services organizations in the US: citizenship as a core function and strategy for growth.

PubMed

Tanenbaum, Sandra J

2011-06-01

Consumer-operated services organizations (COSOs) are independent, non-profit organizations that provide peer support and other non-clinical services to seriously mentally ill people. Mental health consumers provide many of these services and make up at least a majority of the organization's leadership. Although the dominant conception of the COSO is as an adjunct to clinical care in the public mental health system, this paper reconcieves the organization as a civic association and thereby a locus of citizenship. Drawing on empirical research on COSOs in one state and the citizenship and civic democracy literatures, COSOs are analyzed here as membership organizations with democratic norms and strong ties to local communities. The suggestion is made that by embracing and enhancing their status as civic associations, COSOs may advance the goals of the social movement that spawned them and avoid predictable obstacles to further growth and development.

The impact of services that offer individualised funds, shared management, person-centred relationships, and self-direction on the lived experiences of consumers with mental illness.

PubMed

Peterson, Sunila; Buchanan, Angus; Falkmer, Torbjorn

2014-01-01

Mental health service providers across Australia, including Western Australia (WA), have begun to offer individualised funds, shared management, person-centred and self-directed (SPS) services. No research exists on the impact of SPS services on the lived experiences of these particular consumers. This study explored the impact of a SPS service offered for the first time in WA to consumers with mental illness. Data on sixteen consumers' lived experiences were analysed using an abbreviated grounded theory approach. These data had been developed by the consumers, Guides (staff) and an independent evaluator, and most of it had been collected in the past prior to the commencement of the study. Three over-arching categories, and related subcategories, emerged indicating that 1) access to individualised funds enabled practical and psychological benefits to consumers; 2) consistent contact in shared management and person-centred relationships enhanced the provision of timely and meaningful staff support to consumers; and 3) high quality shared management and person-centred relationships with staff and the opportunity to self-direct enabled consumers' change and growth. SPS services enhanced consumers' lived experiences and enabled staff to provide and consumers to experience timely access to recovery resources, consistent contact, responsive and high quality support, and self-direction of services. In this, consumers changed, grew and achieved desired recovery experiences. The overall impact of the SPS service seemed to be founded on the goodness of fit between person characteristics of staff and consumers, which enabled rich support that provided for corrective emotional experiences. This enabled consumers to build meaningful and hopeful lives where they started to live with, and beyond, their mental illness.

Food Adulteration and Consumer Awareness in Dhaka City, 1995-2011

PubMed Central

Ahmed, Tahmeed

2014-01-01

ABSTRACT We conducted this study to investigate the magnitude of food adulteration during 1995–2011 and consumer awareness in Dhaka city. We reviewed results of food sample testing by Public Health Food Laboratory of Dhaka City Corporation, Bangladesh Standards and Testing Institution, Consumers Association of Bangladesh publications, reports from lay press, including those on mobile magistrate court operations. We conducted a cross-sectional survey among 96 residents of Dhaka city, using a structured questionnaire in 2006. The overall proportion of food samples adulterated decreased during 2001-2005, and 40-54% of daily-consumed food was adulterated during 1995-2011. More than 35 food items were commonly adulterated. Consumers considered expiry date and quality or freshness as the best criteria while buying packaged and open food items respectively; only 11 (12%) respondents considered approval of regulatory authority for buying packaged food items. More than half of the food consumed in Dhaka city is adulterated, which warrants actions by the Government, the industry, and the consumers. PMID:25395908

Food adulteration and consumer awareness in Dhaka City, 1995-2011.

PubMed

Nasreen, Sharifa; Ahmed, Tahmeed

2014-09-01

We conducted this study to investigate the magnitude of food adulteration during 1995-2011 and consumer awareness in Dhaka city. We reviewed results of food sample testing by Public Health Food Laboratory of Dhaka City Corporation, Bangladesh Standards and Testing Institution, Consumers Association of Bangladesh publications, reports from lay press, including those on mobile magistrate court operations. We conducted a cross-sectional survey among 96 residents of Dhaka city, using a structured questionnaire in 2006. The overall proportion of food samples adulterated decreased during 2001-2005, and 40-54% of daily-consumed food was adulterated during 1995-2011. More than 35 food items were commonly adulterated. Consumers considered expiry date and quality or freshness as the best criteria while buying packaged and open food items respectively; only 11 (12%) respondents considered approval of regulatory authority for buying packaged food items. More than half of the food consumed in Dhaka city is adulterated, which warrants actions by the Government, the industry, and the consumers.

Performance indicators for quality in surgical and laboratory services at Muhimbili National Hospital (MNH) in Tanzania.

PubMed

Mbembati, Naboth A; Mwangu, Mugwira; Muhondwa, Eustace P Y; Leshabari, Melkizedek M

2008-04-01

Muhimbili National Hospital (MNH), a teaching and national referral hospital, is undergoing major reforms to improve the quality of health care. We performed a retrospective descriptive study using a set of performance indicators for the surgical and laboratory services of MNH in years 2001 and 2002, to help monitor and evaluate the impact of reforms on the quality of health care during and after the reform process. Hospital records were reviewed and information recorded for planned and postponed operations, laboratory equipment, reagents, laboratory tests and quality assurance programmes. In the year 2001 a total of 4332 non-emergency operations were planned, 3313 operations were performed and 1019 (23.5%) operations were postponed. In the year 2002, 4301 non-emergency operations were planned, 3046 were performed and 1255 (29%) were postponed. The most common reasons for operation postponement were "time-barred", interference by emergency operations, no show of patients and inoperable anaesthetic machines. Equipment problems and supply and staff shortages together accounted for one quarter of postponements. In the laboratory, a lack of equipment prevented some tests, but quality assurance was performed for most tests. Current surgical services at MNH are inadequate; operating theatres require modern, functioning equipment and adequate supplies of consumables to provide satisfactory care.

Dental occlusion ties: A rapid, safe, and non‐invasive maxillo‐mandibular fixation technology

PubMed Central

2017-01-01

Objectives For decades, Erich arch bars have been a standard in establishing maxillo‐mandibular fixation (MMF). While reliable, the approach risks sharps injury, consumes operating room time, and inflicts gingival trauma. Newer technologies including screw‐based techniques and “hybrid” techniques have improved MMF by reducing sharps injuries and operating room time, but risk injury to tooth roots, nerves, and gingiva. This study aims to establish the application, strengths, and limitations of dental occlusion ties as a novel alternative in maxillo‐mandibular fixation. Study Design Prospective, non‐blinded, human feasibility clinical trial. Materials and Methods An iterative prototyping process was used to invent dental occlusion ties (brand name: Minne Ties). Development included 3D printing, cadaver prototype testing, human apical embrasure measurement, and ultimately non‐significant risk human clinical trial testing. In the IRB‐approved feasibility clinical trial, the devices were applied to mandible and maxilla fracture candidates with fractures amenable to intra‐operative MMF with open reduction with internal fixation. The ties were removed prior to extubation. Pre‐teens, comminuted fracture patients, and patients requiring post‐operative MMF were excluded. Results Manufactured, sterile prototypes secured MMF successfully in management of unilateral and bilateral mandible and maxilla fractures. All patients reported correction of pre‐operative malocclusion. Application times were typically 12–15 minutes for a single surgeon to achieve MMF. Patients incurred negligible gingival trauma from the technology as the ties require no tissue penetration for application. Conclusions Dental occlusion ties offer a non‐invasive solution featuring operating room efficiency, minimized sharps risk, and less bony and soft tissue trauma than current commercialized solutions. Level of Evidence Therapeutic, IV PMID:28894837

Transfer of a three step mAb chromatography process from batch to continuous: Optimizing productivity to minimize consumable requirements.

PubMed

Gjoka, Xhorxhi; Gantier, Rene; Schofield, Mark

2017-01-20

The goal of this study was to adapt a batch mAb purification chromatography platform for continuous operation. The experiments and rationale used to convert from batch to continuous operation are described. Experimental data was used to design chromatography methods for continuous operation that would exceed the threshold for critical quality attributes and minimize the consumables required as compared to batch mode of operation. Four unit operations comprising of Protein A capture, viral inactivation, flow-through anion exchange (AEX), and mixed-mode cation exchange chromatography (MMCEX) were integrated across two Cadence BioSMB PD multi-column chromatography systems in order to process a 25L volume of harvested cell culture fluid (HCCF) in less than 12h. Transfer from batch to continuous resulted in an increase in productivity of the Protein A step from 13 to 50g/L/h and of the MMCEX step from 10 to 60g/L/h with no impact on the purification process performance in term of contaminant removal (4.5 log reduction of host cell proteins, 50% reduction in soluble product aggregates) and overall chromatography process yield of recovery (75%). The increase in productivity, combined with continuous operation, reduced the resin volume required for Protein A and MMCEX chromatography by more than 95% compared to batch. The volume of AEX membrane required for flow through operation was reduced by 74%. Moreover, the continuous process required 44% less buffer than an equivalent batch process. This significant reduction in consumables enables cost-effective, disposable, single-use manufacturing. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Improving operational plume forecasts

NASA Astrophysics Data System (ADS)

Balcerak, Ernie

2012-04-01

Forecasting how plumes of particles, such as radioactive particles from a nuclear disaster, will be transported and dispersed in the atmosphere is an important but computationally challenging task. During the Fukushima nuclear disaster in Japan, operational plume forecasts were produced each day, but as the emissions continued, previous emissions were not included in the simulations used for forecasts because it became impractical to rerun the simulations each day from the beginning of the accident. Draxler and Rolph examine whether it is possible to improve plume simulation speed and flexibility as conditions and input data change. The authors use a method known as a transfer coefficient matrix approach that allows them to simulate many radionuclides using only a few generic species for the computation. Their simulations work faster by dividing the computation into separate independent segments in such a way that the most computationally time consuming pieces of the calculation need to be done only once. This makes it possible to provide real-time operational plume forecasts by continuously updating the previous simulations as new data become available. They tested their method using data from the Fukushima incident to show that it performed well. (Journal of Geophysical Research-Atmospheres, doi:10.1029/2011JD017205, 2012)

Design and Mechanical Evaluation of a Capacitive Sensor-Based Indexed Platform for Verification of Portable Coordinate Measuring Instruments

PubMed Central

Avila, Agustín Brau; Mazo, Jorge Santolaria; Martín, Juan José Aguilar

2014-01-01

During the last years, the use of Portable Coordinate Measuring Machines (PCMMs) in industry has increased considerably, mostly due to their flexibility for accomplishing in-line measuring tasks as well as their reduced costs and operational advantages as compared to traditional coordinate measuring machines (CMMs). However, their operation has a significant drawback derived from the techniques applied in the verification and optimization procedures of their kinematic parameters. These techniques are based on the capture of data with the measuring instrument from a calibrated gauge object, fixed successively in various positions so that most of the instrument measuring volume is covered, which results in time-consuming, tedious and expensive verification procedures. In this work the mechanical design of an indexed metrology platform (IMP) is presented. The aim of the IMP is to increase the final accuracy and to radically simplify the calibration, identification and verification of geometrical parameter procedures of PCMMs. The IMP allows us to fix the calibrated gauge object and move the measuring instrument in such a way that it is possible to cover most of the instrument working volume, reducing the time and operator fatigue to carry out these types of procedures. PMID:24451458

Design and mechanical evaluation of a capacitive sensor-based indexed platform for verification of portable coordinate measuring instruments.

PubMed

Avila, Agustín Brau; Mazo, Jorge Santolaria; Martín, Juan José Aguilar

2014-01-02

During the last years, the use of Portable Coordinate Measuring Machines (PCMMs) in industry has increased considerably, mostly due to their flexibility for accomplishing in-line measuring tasks as well as their reduced costs and operational advantages as compared to traditional coordinate measuring machines (CMMs). However, their operation has a significant drawback derived from the techniques applied in the verification and optimization procedures of their kinematic parameters. These techniques are based on the capture of data with the measuring instrument from a calibrated gauge object, fixed successively in various positions so that most of the instrument measuring volume is covered, which results in time-consuming, tedious and expensive verification procedures. In this work the mechanical design of an indexed metrology platform (IMP) is presented. The aim of the IMP is to increase the final accuracy and to radically simplify the calibration, identification and verification of geometrical parameter procedures of PCMMs. The IMP allows us to fix the calibrated gauge object and move the measuring instrument in such a way that it is possible to cover most of the instrument working volume, reducing the time and operator fatigue to carry out these types of procedures.

Automation of Coordinated Planning Between Observatories: The Visual Observation Layout Tool (VOLT)

NASA Technical Reports Server (NTRS)

Maks, Lori; Koratkar, Anuradha; Kerbel, Uri; Pell, Vince

2002-01-01

Fulfilling the promise of the era of great observatories, NASA now has more than three space-based astronomical telescopes operating in different wavebands. This situation provides astronomers with the unique opportunity of simultaneously observing a target in multiple wavebands with these observatories. Currently scheduling multiple observatories simultaneously, for coordinated observations, is highly inefficient. Coordinated observations require painstaking manual collaboration among the observatory staff at each observatory. Because they are time-consuming and expensive to schedule, observatories often limit the number of coordinated observations that can be conducted. In order to exploit new paradigms for observatory operation, the Advanced Architectures and Automation Branch of NASA's Goddard Space Flight Center has developed a tool called the Visual Observation Layout Tool (VOLT). The main objective of VOLT is to provide a visual tool to automate the planning of coordinated observations by multiple astronomical observatories. Four of NASA's space-based astronomical observatories - the Hubble Space Telescope (HST), Far Ultraviolet Spectroscopic Explorer (FUSE), Rossi X-ray Timing Explorer (RXTE) and Chandra - are enthusiastically pursuing the use of VOLT. This paper will focus on the purpose for developing VOLT, as well as the lessons learned during the infusion of VOLT into the planning and scheduling operations of these observatories.

Factors affecting dry-cured ham consumer acceptability.

PubMed

Morales, R; Guerrero, L; Aguiar, A P S; Guàrdia, M D; Gou, P

2013-11-01

The objectives of the present study were (1) to compare the relative importance of price, processing time, texture and intramuscular fat in purchase intention of dry-cured ham through conjoint analysis, (2) to evaluate the effect of dry-cured ham appearance on consumer expectations, and (3) to describe the consumer sensory preferences of dry-cured ham using external preference mapping. Texture and processing time influenced the consumer preferences in conjoint analysis. Red colour intensity, colour uniformity, external fat and white film presence/absence influenced consumer expectations. The consumer disliked hams with bitter and metallic flavour and with excessive saltiness and piquantness. Differences between expected and experienced acceptability were found, which indicates that the visual preference of consumers does not allow them to select a dry-cured ham that satisfies their sensory preferences of flavour and texture. Copyright © 2013 Elsevier Ltd. All rights reserved.

Consumer Law-Related Education Materials (Grades 4-7). Highlands County.

ERIC Educational Resources Information Center

Allen, Rodney F., Ed.; Landry, Russell H., Ed.

Intended for students in grades 4-7, the lessons in this guide focus on consumer law-related education. Major objectives are for students to gain an understanding of (1) the laws and legal practices in a democratic society; (2) the concepts of authority, order, property, and justice in the operation of institutions; and (3) the processes and…

10 CFR Appendix B1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Freezers

Code of Federal Regulations, 2011 CFR

2011-01-01

... defrost control. The energy consumption in kilowatt-hours per day shall be calculated equivalent to: ET... though the consumer-activated compartment temperature controls were preset so that the desired... calculated effect of operating a freezer for a period of 24 hours with the consumer-activated controls other...

78 FR 59880 - Enhanced Consumer Protections for Charter Air Transportation

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-30

...) The name of the company in operational control of the aircraft during flight; (2) any other ``doing... disclosure of the entity in operational control of the aircraft during the flight and seven of those comments... different from the entity in operational control of the aircraft, primarily on the basis that these entities...

75 FR 14131 - Effect on Propane Consumers of the Propane Education and Research Council's Operations, Market...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-24

... Education and Research Council (PERC), in conjunction with the cumulative effects of market changes and... the Secretary of Energy a report examining whether operation of the Council, in conjunction with the...

A Methodology for Flight-Time Identification of Helicopter-Slung Load Frequency Response Characteristics Using CIFER

NASA Technical Reports Server (NTRS)

Sahai, Ranjana; Pierce, Larry; Cicolani, Luigi; Tischler, Mark

1998-01-01

Helicopter slung load operations are common in both military and civil contexts. The slung load adds load rigid body modes, sling stretching, and load aerodynamics to the system dynamics, which can degrade system stability and handling qualities, and reduce the operating envelope of the combined system below that of the helicopter alone. Further, the effects of the load on system dynamics vary significantly among the large range of loads, slings, and flight conditions that a utility helicopter will encounter in its operating life. In this context, military helicopters and loads are often qualified for slung load operations via flight tests which can be time consuming and expensive. One way to reduce the cost and time required to carry out these tests and generate quantitative data more readily is to provide an efficient method for analysis during the flight, so that numerous test points can be evaluated in a single flight test, with evaluations performed in near real time following each test point and prior to clearing the aircraft to the next point. Methodology for this was implemented at Ames and demonstrated in slung load flight tests in 1997 and was improved for additional flight tests in 1999. The parameters of interest for the slung load tests are aircraft handling qualities parameters (bandwidth and phase delay), stability margins (gain and phase margin), and load pendulum roots (damping and natural frequency). A procedure for the identification of these parameters from frequency sweep data was defined using the CIFER software package. CIFER is a comprehensive interactive package of utilities for frequency domain analysis previously developed at Ames for aeronautical flight test applications. It has been widely used in the US on a variety of aircraft, including some primitive flight time analysis applications.

Real-time measurement system for evaluation of the carotid intima-media thickness with a robust edge operator.

PubMed

Faita, Francesco; Gemignani, Vincenzo; Bianchini, Elisabetta; Giannarelli, Chiara; Ghiadoni, Lorenzo; Demi, Marcello

2008-09-01

The purpose of this report is to describe an automatic real-time system for evaluation of the carotid intima-media thickness (CIMT) characterized by 3 main features: minimal interobserver and intraobserver variability, real-time capabilities, and great robustness against noise. One hundred fifty carotid B-mode ultrasound images were used to validate the system. Two skilled operators were involved in the analysis. Agreement with the gold standard, defined as the mean of 2 manual measurements of a skilled operator, and the interobserver and intraobserver variability were quantitatively evaluated by regression analysis and Bland-Altman statistics. The automatic measure of the CIMT showed a mean bias +/- SD of 0.001 +/- 0.035 mm toward the manual measurement. The intraobserver variability, evaluated with Bland-Altman plots, showed a bias that was not significantly different from 0, whereas the SD of the differences was greater in the manual analysis (0.038 mm) than in the automatic analysis (0.006 mm). For interobserver variability, the automatic measurement had a bias that was not significantly different from 0, with a satisfactory SD of the differences (0.01 mm), whereas in the manual measurement, a little bias was present (0.012 mm), and the SD of the differences was noticeably greater (0.044 mm). The CIMT has been accepted as a noninvasive marker of early vascular alteration. At present, the manual approach is largely used to estimate CIMT values. However, that method is highly operator dependent and time-consuming. For these reasons, we developed a new system for the CIMT measurement that conjugates precision with real-time analysis, thus providing considerable advantages in clinical practice.

The Effects of Consumer Education on Consumer Search.

ERIC Educational Resources Information Center

Fast, Janet; And Others

1989-01-01

A study investigated the relationship between selected consumer and marketplace characteristics and consumers' prepurchase allocation of search time among information sources (product test reports; dealer sales representatives; advertisements; family and friends). The household production model proved useful; written educational materials appeared…

Functional Requirements for Onboard Management of Space Shuttle Consumables. Volume 2

NASA Technical Reports Server (NTRS)

Graf, P. J.; Herwig, H. A.; Neel, L. W.

1973-01-01

This report documents the results of the study "Functional Requirements for Onboard Management of Space Shuttle Consumables." The study was conducted for the Mission Planning and Analysis Division of the NASA Lyndon B. Johnson Space Center, Houston, Texas, between 3 July 1972 and 16 November 1973. The overall study program objective was two-fold. The first objective was to define a generalized consumable management concept which is applicable to advanced spacecraft. The second objective was to develop a specific consumables management concept for the Space Shuttle vehicle and to generate the functional requirements for the onboard portion of that concept. Consumables management is the process of controlling or influencing the usage of expendable materials involved in vehicle subsystem operation. The report consists of two volumes. Volume I presents a description of the study activities related to general approaches for developing consumable management, concepts for advanced spacecraft applications, and functional requirements for a Shuttle consumables management concept. Volume II presents a detailed description of the onboard consumables management concept proposed for use on the Space Shuttle.

Precision in robotic rectal surgery using the da Vinci Xi system and integrated table motion, a technical note.

PubMed

Panteleimonitis, Sofoklis; Harper, Mick; Hall, Stuart; Figueiredo, Nuno; Qureshi, Tahseen; Parvaiz, Amjad

2017-09-15

Robotic rectal surgery is becoming increasingly more popular among colorectal surgeons. However, time spent on robotic platform docking, arm clashing and undocking of the platform during the procedure are factors that surgeons often find cumbersome and time consuming. The newest surgical platform, the da Vinci Xi, coupled with integrated table motion can help to overcome these problems. This technical note aims to describe a standardised operative technique of single docking robotic rectal surgery using the da Vinci Xi system and integrated table motion. A stepwise approach of the da Vinci docking process and surgical technique is described accompanied by an intra-operative video that demonstrates this technique. We also present data collected from a prospectively maintained database. 33 consecutive rectal cancer patients (24 male, 9 female) received robotic rectal surgery with the da Vinci Xi during the preparation of this technical note. 29 (88%) patients had anterior resections, and four (12%) had abdominoperineal excisions. There were no conversions, no anastomotic leaks and no mortality. Median operation time was 331 (249-372) min, blood loss 20 (20-45) mls and length of stay 6.5 (4-8) days. 30-day readmission rate and re-operation rates were 3% (n = 1). This standardised technique of single docking robotic rectal surgery with the da Vinci Xi is safe, feasible and reproducible. The technological advances of the new robotic system facilitate the totally robotic single docking approach.

Socio-economic differences in takeaway food consumption among adults.

PubMed

Miura, Kyoko; Giskes, Katrina; Turrell, Gavin

2012-02-01

To examine socio-economic differences in the frequency and types of takeaway foods consumed. A cross-sectional postal survey. Participants were asked about their usual consumption of overall takeaway food (<4 times/month or ≥4 times/month) and of twenty-two specific takeaway food items (<1 time/month or ≥1 time/month); these latter foods were grouped into 'healthy' and 'less healthy' choices. Socio-economic position was measured on the basis of educational level and equivalised household income, and differences in takeaway food consumption were assessed by calculating prevalence ratios using log binomial regression. Adults aged 25-64 years from Brisbane, Australia, were randomly selected from the electoral roll (n 903; 63·7 % response rate). Compared with their more educated counterparts, the least educated were more regular consumers of overall takeaway food and fruit or vegetable juice and less regular consumers of sushi. For the 'less healthy' items, the least educated more regularly consumed potato chips, savoury pies, fried chicken and non-diet soft drinks; however, the least educated were less likely to consume curry. Household income was not associated with overall takeaway consumption. The lowest-income group was a more regular consumer of fruit or vegetable juice compared with the highest-income group. Among the 'less healthy' items, the lowest-income group was a more regular consumer of fried fish, ice cream and milk shakes, whereas curry was consumed less regularly. The frequency and types of takeaway foods consumed by socio-economically disadvantaged groups may contribute to inequalities in overweight or obesity and to chronic disease.

12 CFR 227.22 - Unfair acts or practices regarding time to make payment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... THE FEDERAL RESERVE SYSTEM UNFAIR OR DECEPTIVE ACTS OR PRACTICES (REGULATION AA) Consumer Credit Card.... Except as provided in paragraph (c) of this section, a bank must not treat a payment on a consumer credit card account as late for any purpose unless the consumer has been provided a reasonable amount of time...

75 FR 36639 - Change in Times for Meeting of Chronic Hazard Advisory Panel on Phthalates and Phthalate...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

... children's toys and child care articles, pursuant to section 108 of the Consumer Product Safety Improvement..., pursuant to section 108 of the Consumer Product Safety Improvement Act of 2008 (CPSIA) (Pub. L. 110-314... CONSUMER PRODUCT SAFETY COMMISSION Change in Times for Meeting of Chronic Hazard Advisory Panel on...

An investigation of used electronics return flows: A data-driven approach to capture and predict consumers storage and utilization behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabbaghi, Mostafa, E-mail: mostafas@buffalo.edu; Esmaeilian, Behzad, E-mail: b.esmaeilian@neu.edu; Raihanian Mashhadi, Ardeshir, E-mail: ardeshir@buffalo.edu

Highlights: • We analyzed a data set of HDDs returned back to an e-waste collection site. • We studied factors that affect the storage behavior. • Consumer type, brand and size are among factors which affect the storage behavior. • Commercial consumers have stored computers more than household consumers. • Machine learning models were used to predict the storage behavior. - Abstract: Consumers often have a tendency to store their used, old or un-functional electronics for a period of time before they discard them and return them back to the waste stream. This behavior increases the obsolescence rate of usedmore » still-functional products leading to lower profitability that could be resulted out of End-of-Use (EOU) treatments such as reuse, upgrade, and refurbishment. These types of behaviors are influenced by several product and consumer-related factors such as consumers’ traits and lifestyles, technology evolution, product design features, product market value, and pro-environmental stimuli. Better understanding of different groups of consumers, their utilization and storage behavior and the connection of these behaviors with product design features helps Original Equipment Manufacturers (OEMs) and recycling and recovery industry to better overcome the challenges resulting from the undesirable storage of used products. This paper aims at providing insightful statistical analysis of Electronic Waste (e-waste) dynamic nature by studying the effects of design characteristics, brand and consumer type on the electronics usage time and end of use time-in-storage. A database consisting of 10,063 Hard Disk Drives (HDD) of used personal computers returned back to a remanufacturing facility located in Chicago, IL, USA during 2011–2013 has been selected as the base for this study. The results show that commercial consumers have stored computers more than household consumers regardless of brand and capacity factors. Moreover, a heterogeneous storage behavior is observed for different brands of HDDs regardless of capacity and consumer type factors. Finally, the storage behavior trends are projected for short-time forecasting and the storage times are precisely predicted by applying machine learning methods.« less

Cattle traceability system in Japan for bovine spongiform encephalopathy.

PubMed

Sugiura, Katsuaki; Onodera, Takashi

2008-01-01

To promote consumer confidence in the safety of beef and to ensure the proper implementation of eradication measures against bovine spongiform encephalopathy (BSE), the Cattle Traceability Law was approved by the Diet in June 2003 and a cattle traceability system has been in operation in Japan since December 2003. The system enables tracing the cohort and offspring animals of a BSE case within 24 h of its detection. The traceability database system also provides distributors, restaurants and consumers with information on the cattle from which the beef that they sell, serve and consume, originate.

The Field Artillery Battalion on the Nuclear Battlefield

DTIC Science & Technology

1975-06-06

flexibility of radio communications. The drawback to tactical wire communications is that the estao- lishment and maintenance of the system is time consuming ...Adjusted fires are a much simpler, though time consum - ing mission. Whatever the inaccuracies in target location, 16 . ■■■ ■’■"’ rgfimtm...SCP). The current practice of a separate SCP for the 8", SP battalion is both time consuming and illogical. Service support The application of the

Hydrodynamics study on drying of pepper in swirling fluidized bed dryer (SFBD)

NASA Astrophysics Data System (ADS)

Syaif Haron, Nazrul; Hazri Zakaria, Jamal; Faizal Mohideen Batcha, Mohd

2017-08-01

Malaysia is one of the pepper producer with exports quantity reaching more than 90000 tonnes between 2010 until 2016. Drying of pepper is mandatory before their export and at present, pepper was dried by sun drying to reduce cost. This conventional drying method was time consuming and may take four days during rainy season, which retards the production of pepper. This paper proposes the swirling fluidized bed drying (SFBD) method, which was known to have high mixing ability and improved solid-gas contact to shorten the drying time of products. A lab scale SFBD system was constructed to carry out this study. Hydrodynamic study was conducted for three beds loadings of 1.0 kg, 1.4 kg at a drying temperature of 90°C. The SFBD has shown excellent potential to dry the pepper with a relatively short drying time compared to the conventional method. Batch drying for the bed loads studied only took 3 hours of drying time only. It was found that bed higher bed loading of wet pepper requires longer drying time due to higher amount of moisture content in the bed. Four distinct regimes of operation were found during drying in the SFBD and these regimes offer flexibility of operation. The total bed pressure drop was relatively low during drying.

Improving 3D Character Posing with a Gestural Interface.

PubMed

Kyto, Mikko; Dhinakaran, Krupakar; Martikainen, Aki; Hamalainen, Perttu

2017-01-01

The most time-consuming part of character animation is 3D character posing. Posing using a mouse is a slow and tedious task that involves sequences of selecting on-screen control handles and manipulating the handles to adjust character parameters, such as joint rotations and end effector positions. Thus, various 3D user interfaces have been proposed to make animating easier, but they typically provide less accuracy. The proposed interface combines a mouse with the Leap Motion device to provide 3D input. A usability study showed that users preferred the Leap Motion over a mouse as a 3D gestural input device. The Leap Motion drastically decreased the number of required operations and the task completion time, especially for novice users.

A novel track-before-detect algorithm based on optimal nonlinear filtering for detecting and tracking infrared dim target

NASA Astrophysics Data System (ADS)

Tian, Yuexin; Gao, Kun; Liu, Ying; Han, Lu

2015-08-01

Aiming at the nonlinear and non-Gaussian features of the real infrared scenes, an optimal nonlinear filtering based algorithm for the infrared dim target tracking-before-detecting application is proposed. It uses the nonlinear theory to construct the state and observation models and uses the spectral separation scheme based Wiener chaos expansion method to resolve the stochastic differential equation of the constructed models. In order to improve computation efficiency, the most time-consuming operations independent of observation data are processed on the fore observation stage. The other observation data related rapid computations are implemented subsequently. Simulation results show that the algorithm possesses excellent detection performance and is more suitable for real-time processing.

33 Years of Continuous Solar Radio Flux Observations

NASA Astrophysics Data System (ADS)

Monstein, Christian

2015-10-01

In 1982, after development and testing of several analog receiver concepts, I started continuous solar radio flux observations at 230 MHz. My instruments for the observations were based on cheap commercial components out of consumer TV electronics. The main components included a TV-tuner (at that time analog), intermediate frequency (IF) amplifier and video-detector taken from used TV sets. The 5.5 MHz wide video signal was fed into an integrating circuit, in fact a low pass filter, followed by dc-offset circuit and dc-amplifier built with four ua741 and CA3140 operational amplifier integrated circuits. At that time the signal was recorded with a Heathkit stripchart recorder and ink pen; an example is shown in figure 1.

National Economic Policies: The Impact on Consumer Welfare. Proceedings of the American Council on Consumer Interests Annual Conference (29th, Kansas City, Missouri, March 16-19, 1983).

ERIC Educational Resources Information Center

Goebel, Karen P., Ed.

These proceedings contain the texts of the papers presented at a conference on consumer interests. Addressed in the first series of concurrent sessions are the following topics: consumers' new economic positions, consumers' choices with respect to price and quality trade-offs, time value in consumption decisions, and consumer information issues.…

A low-rank matrix recovery approach for energy efficient EEG acquisition for a wireless body area network.

PubMed

Majumdar, Angshul; Gogna, Anupriya; Ward, Rabab

2014-08-25

We address the problem of acquiring and transmitting EEG signals in Wireless Body Area Networks (WBAN) in an energy efficient fashion. In WBANs, the energy is consumed by three operations: sensing (sampling), processing and transmission. Previous studies only addressed the problem of reducing the transmission energy. For the first time, in this work, we propose a technique to reduce sensing and processing energy as well: this is achieved by randomly under-sampling the EEG signal. We depart from previous Compressed Sensing based approaches and formulate signal recovery (from under-sampled measurements) as a matrix completion problem. A new algorithm to solve the matrix completion problem is derived here. We test our proposed method and find that the reconstruction accuracy of our method is significantly better than state-of-the-art techniques; and we achieve this while saving sensing, processing and transmission energy. Simple power analysis shows that our proposed methodology consumes considerably less power compared to previous CS based techniques.

PHA production by mixed cultures: a way to valorize wastes from pulp industry.

PubMed

Queirós, Diogo; Rossetti, Simona; Serafim, Luísa S

2014-04-01

In this work, hardwood spent sulfite liquor (HSSL), a complex feedstock originating from the pulp industry, was tested for the first time as a substrate for polyhydroxyalkanoate (PHA) production by a mixed microbial culture (MMC) under aerobic dynamic feeding (ADF) conditions. A sequencing batch reactor (SBR) fed with HSSL was operated for 67days and the selected MMC reached a maximum PHA content of 67.6%. The MMC demonstrated a differential utilization of the carbon sources present in HSSL. Acetic acid was fully consumed, while xylose and lignosulphonates were partially consumed (30% and 14%, respectively). The selected culture was characterized by Fluorescence in Situ Hybridization (FISH). Bacteria belonging to the three main classes were identified: Alpha- (72.7±4.0%), Beta- (11.1±0.37%) and Gammaproteobacteria (10.3±0.3%). Within Alphaproteobacteria, a small amount of Paracoccus (4.2±0.51%) and Defluvicoccus related to Tetrad Forming Organisms (9.0±0.28%) were detected. Copyright © 2014 Elsevier Ltd. All rights reserved.

Design of time-pulse coded optoelectronic neuronal elements for nonlinear transformation and integration

NASA Astrophysics Data System (ADS)

Krasilenko, Vladimir G.; Nikolsky, Alexander I.; Lazarev, Alexander A.; Lazareva, Maria V.

2008-03-01

In the paper the actuality of neurophysiologically motivated neuron arrays with flexibly programmable functions and operations with possibility to select required accuracy and type of nonlinear transformation and learning are shown. We consider neurons design and simulation results of multichannel spatio-time algebraic accumulation - integration of optical signals. Advantages for nonlinear transformation and summation - integration are shown. The offered circuits are simple and can have intellectual properties such as learning and adaptation. The integrator-neuron is based on CMOS current mirrors and comparators. The performance: consumable power - 100...500 μW, signal period- 0.1...1ms, input optical signals power - 0.2...20 μW time delays - less 1μs, the number of optical signals - 2...10, integration time - 10...100 of signal periods, accuracy or integration error - about 1%. Various modifications of the neuron-integrators with improved performance and for different applications are considered in the paper.

Hydraulic Robotic Surgical Tool Changing Manipulator

PubMed Central

Pourghodrat, Abolfazl; Nelson, Carl A.; Oleynikov, Dmitry

2017-01-01

Natural orifice transluminal endoscopic surgery (NOTES) is a surgical technique to perform “scarless” abdominal operations. Robotic technology has been exploited to improve NOTES and circumvent its limitations. Lack of a multitasking platform is a major limitation. Manual tool exchange can be time consuming and may lead to complications such as bleeding. Previous multifunctional manipulator designs use electric motors. These designs are bulky, slow, and expensive. This paper presents design, prototyping, and testing of a hydraulic robotic tool changing manipulator. The manipulator is small, fast, low-cost, and capable of carrying four different types of laparoscopic instruments. PMID:28450979

Portable data flow in UNIX

NASA Astrophysics Data System (ADS)

Fox, R.; Molen, A. Vander; Hannuschke, S.

1994-02-01

We describe the dataflow of a nuclear physics data acquisition system. The system features a high speed active routing subsystem which allows an arbitrary number of data producers to contribute data to the system. Data are then routed to an arbitrary number of data consumers. Low overhead route-by-reference mechanisms are used to allow high rate operations. The system has been ported to a variety of UNIX systems. Timings are given for the routing component of the system on several systems. Finally, we give an example of a set of programs which can be added to the system to produce a complete data acquisition system.

CAD system for footwear design based on whole real 3D data of last surface

NASA Astrophysics Data System (ADS)

Song, Wanzhong; Su, Xianyu

2000-10-01

Two major parts of application of CAD in footwear design are studied: the development of last surface; computer-aided design of planar shoe-template. A new quasi-experiential development algorithm of last surface based on triangulation approximation is presented. This development algorithm consumes less time and does not need any interactive operation for precisely development compared with other development algorithm of last surface. Based on this algorithm, a software, SHOEMAKERTM, which contains computer aided automatic measurement, automatic development of last surface and computer aide design of shoe-template has been developed.

Transmasseteric antero-parotid approach for open reduction and internal fixation of condylar fractures.

PubMed

Wilson, A W; Ethunandan, M; Brennan, P A

2005-02-01

The morbidity that results from surgical approaches to the condylar neck, and the time-consuming nature of the operation inhibits many surgeons from using open reduction and internal fixation for the treatment of condylar fractures. The many approaches that have been described stand testimony to the disadvantages of the individual techniques. The most common problems are limited access and injury to the facial nerve. We describe the transmasseteric antero-parotid (TMAP) technique, which offers swift access to the condylar neck while substantially reducing the risk to the facial nerve and eliminating the complications associated with transparotid approaches.

Analytical solution of tt¯ dilepton equations

NASA Astrophysics Data System (ADS)

Sonnenschein, Lars

2006-03-01

The top quark antiquark production system in the dilepton decay channel is described by a set of equations which is nonlinear in the unknown neutrino momenta. Its most precise and least time consuming solution is of major importance for measurements of top quark properties like the top quark mass and tt¯ spin correlations. The initial system of equations can be transformed into two polynomial equations with two unknowns by means of elementary algebraic operations. These two polynomials of multidegree two can be reduced to one univariate polynomial of degree four by means of resultants. The obtained quartic equation is solved analytically.

Simulation of TunneLadder traveling-wave tube cold-test characteristics: Implementation of the three-dimensional, electromagnetic circuit analysis code micro-SOS

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Wilson, Jeffrey D.

1993-01-01

The three-dimensional, electromagnetic circuit analysis code, Micro-SOS, can be used to reduce expensive time-consuming experimental 'cold-testing' of traveling-wave tube (TWT) circuits. The frequency-phase dispersion characteristics and beam interaction impedance of a TunneLadder traveling-wave tube slow-wave structure were simulated using the code. When reasonable dimensional adjustments are made, computer results agree closely with experimental data. Modifications to the circuit geometry that would make the TunneLadder TWT easier to fabricate for higher frequency operation are explored.

"Juice Monsters": Sub-Ohm Vaping and Toxic Volatile Aldehyde Emissions.

PubMed

Talih, Soha; Salman, Rola; Karaoghlanian, Nareg; El-Hellani, Ahmad; Saliba, Najat; Eissenberg, Thomas; Shihadeh, Alan

2017-10-16

An emerging category of electronic cigarettes (ECIGs) is sub-Ohm devices (SODs) that operate at ten or more times the power of conventional ECIGs. Because carcinogenic volatile aldehyde (VA) emissions increase sharply with power, SODs may expose users to greater VAs. In this study, we compared VA emissions from several SODs and found that across device, VAs and power were uncorrelated unless power was normalized by coil surface area. VA emissions and liquid consumed were correlated highly. Analyzed in light of EU regulations limiting ECIG liquid nicotine concentration, these findings suggest potential regulatory levers and pitfalls for protecting public health.

Citizen journalism in a time of crisis: lessons from a large-scale California wildfire

Treesearch

S. Gillette; J. Taylor; D.J. Chavez; R. Hodgson; J. Downing

2007-01-01

The accessibility of news production tools through consumer communication technology has made it possible for media consumers to become media producers. The evolution of media consumer to media producer has important implications for the shape of public discourse during a time of crisis. Citizen journalists cover crisis events using camera cell phones and digital...

THE ROLE OF FARMERS IN MANAGING WATER Dr Tony Colman Professor Tony Allan Farmers manage about 92% of the water consumed by society which needs to recognise that farming practices and the decisions made by those who operate food supply chains - including corporates and those making public policy - determine how water is stewarded.

NASA Astrophysics Data System (ADS)

Colman, A. J.

2017-12-01

Title Food-water and society Dr. Tony Colman and Professor Tony Allan Abstract The purpose of the paper is to highlight some key relationships between water resources and society. First, water is an very important resource for society in that it provides an essential input to society's food supply chains. Secondly, it is an essential input to farmer livelihoods. About half of the families of the world still work in agriculture - albeit a declining proportion. Thirdly, farmers manage about 92% of the water consumed by society - including the blue water (surface and groundwater) for irrigation and the green water (effective rainfall) consumed on rainfed farms. They also account for about 66% of society's impacts on biodiversity and about 25% of emissions. Finally it will be argued that those who analyse allocation and management of water must recognise that farming practices and the decisions made by those who operate food supply chains - including corporates and those making public policy - must recognise that it is farmers and food consumers who determine how water is stewarded. It will be suggested that we need to understand that well informed consumers could be the regulators.

Voice Over Internet Protocol (VoIP) in a Control Center Environment

NASA Technical Reports Server (NTRS)

Pirani, Joseph; Calvelage, Steven

2010-01-01

The technology of transmitting voice over data networks has been available for over 10 years. Mass market VoIP services for consumers to make and receive standard telephone calls over broadband Internet networks have grown in the last 5 years. While operational costs are less with VoIP implementations as opposed to time division multiplexing (TDM) based voice switches, is it still advantageous to convert a mission control center s voice system to this newer technology? Marshall Space Flight Center (MSFC) Huntsville Operations Support Center (HOSC) has converted its mission voice services to a commercial product that utilizes VoIP technology. Results from this testing, design, and installation have shown unique considerations that must be addressed before user operations. There are many factors to consider for a control center voice design. Technology advantages and disadvantages were investigated as they refer to cost. There were integration concerns which could lead to complex failure scenarios but simpler integration for the mission infrastructure. MSFC HOSC will benefit from this voice conversion with less product replacement cost, less operations cost and a more integrated mission services environment.

Integrating Machine Learning into Space Operations

NASA Astrophysics Data System (ADS)

Kelly, K. G.

There are significant challenges with managing activities in space, which for the scope of this paper are primarily the identification of objects in orbit, maintaining accurate estimates of the orbits of those objects, detecting changes to those orbits, warning of possible collisions between objects and detection of anomalous behavior. The challenges come from the large amounts of data to be processed, which is often incomplete and noisy, limitations on the ability to influence objects in space and the overall strategic importance of space to national interests. The focus of this paper is on defining an approach to leverage the improved capabilities that are possible using state of the art machine learning in a way that empowers operations personnel without sacrificing the security and mission assurance associated with manual operations performed by trained personnel. There has been significant research in the development of algorithms and techniques for applying machine learning in this domain, but deploying new techniques into such a mission critical domain is difficult and time consuming. Establishing a common framework could improve the efficiency with which new techniques are integrated into operations and the overall effectiveness at providing improvements.

Resource planning and scheduling of payload for satellite with particle swarm optimization

NASA Astrophysics Data System (ADS)

Li, Jian; Wang, Cheng

2007-11-01

The resource planning and scheduling technology of payload is a key technology to realize an automated control for earth observing satellite with limited resources on satellite, which is implemented to arrange the works states of various payloads to carry out missions by optimizing the scheme of the resources. The scheduling task is a difficult constraint optimization problem with various and mutative requests and constraints. Based on the analysis of the satellite's functions and the payload's resource constraints, a proactive planning and scheduling strategy based on the availability of consumable and replenishable resources in time-order is introduced along with dividing the planning and scheduling period to several pieces. A particle swarm optimization algorithm is proposed to address the problem with an adaptive mutation operator selection, where the swarm is divided into groups with different probabilities to employ various mutation operators viz., differential evolution, Gaussian and random mutation operators. The probabilities are adjusted adaptively by comparing the effectiveness of the groups to select a proper operator. The simulation results have shown the feasibility and effectiveness of the method.

Determinants of choice for pigeons and humans on concurrent-chains schedules of reinforcement.

PubMed

Belke, T W; Pierce, W D; Powell, R A

1989-09-01

Concurrent-chains schedules of reinforcement were arranged for humans and pigeons. Responses of humans were reinforced with tokens exchangeable for money, and key pecks of 4 birds were reinforced with food. Variable-interval 30-s and 40-s schedules operated in the terminal links of the chains. Condition 1 exposed subjects to variable-interval 90-s and variable-interval 30-s initial links, respectively. Conditions 2 and 3 arranged equal initial-link schedules of 40 s or 120 s. Experimental conditions tested the descriptive adequacy of five equations: reinforcement density, delay reduction, modified delay reduction, matching and maximization. Results based on choice proportions and switch rates during the initial links showed that pigeons behaved in accord with delay-reduction models, whereas humans maximized overall rate of reinforcement. As discussed by Logue and associates in self-control research, different types of reinforcement may affect sensitivity to delay differentially. Pigeons' responses were reinforced with food, a reinforcer that is consumable upon presentation. Humans' responses were reinforced with money, a reinforcer exchanged for consumable reinforcers after it was earned. Reinforcers that are immediately consumed may generate high sensitivity to delay and behavior described as delay reduction. Reinforces with longer times to consumption may generate low sensitivity to delay and behavior that maximizes overall payoff.

SHEDS-HT: An Integrated Probabilistic Exposure Model for ...

EPA Pesticide Factsheets

United States Environmental Protection Agency (USEPA) researchers are developing a strategy for highthroughput (HT) exposure-based prioritization of chemicals under the ExpoCast program. These novel modeling approaches for evaluating chemicals based on their potential for biologically relevant human exposures will inform toxicity testing and prioritization for chemical risk assessment. Based on probabilistic methods and algorithms developed for The Stochastic Human Exposure and Dose Simulation Model for Multimedia, Multipathway Chemicals (SHEDS-MM), a new mechanistic modeling approach has been developed to accommodate high-throughput (HT) assessment of exposure potential. In this SHEDS-HT model, the residential and dietary modules of SHEDS-MM have been operationally modified to reduce the user burden, input data demands, and run times of the higher-tier model, while maintaining critical features and inputs that influence exposure. The model has been implemented in R; the modeling framework links chemicals to consumer product categories or food groups (and thus exposure scenarios) to predict HT exposures and intake doses. Initially, SHEDS-HT has been applied to 2507 organic chemicals associated with consumer products and agricultural pesticides. These evaluations employ data from recent USEPA efforts to characterize usage (prevalence, frequency, and magnitude), chemical composition, and exposure scenarios for a wide range of consumer products. In modeling indirec

Support vector machine for day ahead electricity price forecasting

NASA Astrophysics Data System (ADS)

Razak, Intan Azmira binti Wan Abdul; Abidin, Izham bin Zainal; Siah, Yap Keem; Rahman, Titik Khawa binti Abdul; Lada, M. Y.; Ramani, Anis Niza binti; Nasir, M. N. M.; Ahmad, Arfah binti

2015-05-01

Electricity price forecasting has become an important part of power system operation and planning. In a pool- based electric energy market, producers submit selling bids consisting in energy blocks and their corresponding minimum selling prices to the market operator. Meanwhile, consumers submit buying bids consisting in energy blocks and their corresponding maximum buying prices to the market operator. Hence, both producers and consumers use day ahead price forecasts to derive their respective bidding strategies to the electricity market yet reduce the cost of electricity. However, forecasting electricity prices is a complex task because price series is a non-stationary and highly volatile series. Many factors cause for price spikes such as volatility in load and fuel price as well as power import to and export from outside the market through long term contract. This paper introduces an approach of machine learning algorithm for day ahead electricity price forecasting with Least Square Support Vector Machine (LS-SVM). Previous day data of Hourly Ontario Electricity Price (HOEP), generation's price and demand from Ontario power market are used as the inputs for training data. The simulation is held using LSSVMlab in Matlab with the training and testing data of 2004. SVM that widely used for classification and regression has great generalization ability with structured risk minimization principle rather than empirical risk minimization. Moreover, same parameter settings in trained SVM give same results that absolutely reduce simulation process compared to other techniques such as neural network and time series. The mean absolute percentage error (MAPE) for the proposed model shows that SVM performs well compared to neural network.

Thermostat Interface and Usability: A Survey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meier, Alan; Peffer, Therese; Pritoni, Marco

2010-09-04

This report investigates the history of thermostats to better understand the context and legacy regarding the development of this important tool, as well as thermostats' relationships to heating, cooling, and other environmental controls. We analyze the architecture, interfaces, and modes of interaction used by different types of thermostats. For over sixty years, home thermostats have translated occupants' temperature preferences into heating and cooling system operations. In this position of an intermediary, the millions of residential thermostats control almost half of household energy use, which corresponds to about 10percent of the nation's total energy use. Thermostats are currently undergoing rapid developmentmore » in response to emerging technologies, new consumer and utility demands, and declining manufacturing costs. Energy-efficient homes require more careful balancing of comfort, energy consumption, and health. At the same time, new capabilities will be added to thermostats, including scheduling, control of humidity and ventilation, responsiveness to dynamic electricity prices, and the ability to join communication networks inside homes. Recent studies have found that as many as 50percent of residential programmable thermostats are in permanent"hold" status. Other evaluations found that homes with programmable thermostats consumed more energy than those relying on manual thermostats. Occupants find thermostats cryptic and baffling to operate because manufacturers often rely on obscure, and sometimes even contradictory, terms, symbols, procedures, and icons. It appears that many people are unable to fully exploit even the basic features in today's programmable thermostats, such as setting heating and cooling schedules. It is important that people can easily, reliably, and confidently operate thermostats in their homes so as to remain comfortable while minimizing energy use.« less

Customer and household matching: resolving entity identity in data warehouses

NASA Astrophysics Data System (ADS)

Berndt, Donald J.; Satterfield, Ronald K.

2000-04-01

The data preparation and cleansing tasks necessary to ensure high quality data are among the most difficult challenges faced in data warehousing and data mining projects. The extraction of source data, transformation into new forms, and loading into a data warehouse environment are all time consuming tasks that can be supported by methodologies and tools. This paper focuses on the problem of record linkage or entity matching, tasks that can be very important in providing high quality data. Merging two or more large databases into a single integrated system is a difficult problem in many industries, especially in the wake of acquisitions. For example, managing customer lists can be challenging when duplicate entries, data entry problems, and changing information conspire to make data quality an elusive target. Common tasks with regard to customer lists include customer matching to reduce duplicate entries and household matching to group customers. These often O(n2) problems can consume significant resources, both in computing infrastructure and human oversight, and the goal of high accuracy in the final integrated database can be difficult to assure. This paper distinguishes between attribute corruption and entity corruption, discussing the various impacts on quality. A metajoin operator is proposed and used to organize past and current entity matching techniques. Finally, a logistic regression approach to implementing the metajoin operator is discussed and illustrated with an example. The metajoin can be used to determine whether two records match, don't match, or require further evaluation by human experts. Properly implemented, the metajoin operator could allow the integration of individual databases with greater accuracy and lower cost.

Consumer involvement in the health technology assessment program.

PubMed

Royle, Jane; Oliver, Sandy

2004-01-01

This study aims to describe a cycle of development leading to sustainable methods for involving consumers in the management of a program commissioning health technology assessment. Staff time was dedicated to developing procedures for recruiting and briefing consumers to participate in prioritizing, commissioning, and reporting research. Resources and support were developed in light of early feedback from consumers and those working with them. These were piloted and amended before being used routinely. Over 4 years, procedures and resources have been developed to support six consumers attending seven to eight prioritization meetings a year; thirty to forty-five consumers each year commenting on research need for particular topics; thirty consumers a year commenting on research proposals, and twenty a year commenting on research reports. The procedures include clear job descriptions, induction and development days, clear briefing materials, payment for substantial tasks, and regularly seeking feedback to improve procedures. Explicit, inclusive, and reproducible methods for supporting consumer involvement that satisfy National Health Service policy recommendations for involving consumers in research require dedicated staff time to support a cycle of organizational development.

Value of outpatient follow-up after curative surgery for carcinoma of the large bowel.

PubMed

Cochrane, J P; Williams, J T; Faber, R G; Slack, W W

1980-03-01

The records were reviewed of 406 patients with carcinoma of the large bowel who had been treated at the Middlesex Hospital during 1958-62. Of these patients, 180 were followed up regularly in this hospital after radical surgery, and from six months to 15 years after operation they were seen 2319 times; 71 developed a recurrent carcinoma but, of these, 41 recurrences (58%) were diagnosed at times other than those of the patients' routine outpatient appointments, although they were being regularly reviewed. Only one patient with recurrence appeared to have been cured by further surgery. For the present, adequate education of patients in the symptoms of early recurrence, with instruction to return if any of these develop, is likely to be more effective than the unsatisfactory and time-consuming routine follow-up still used in many hospitals.

Algorithmic synthesis using Python compiler

NASA Astrophysics Data System (ADS)

Cieszewski, Radoslaw; Romaniuk, Ryszard; Pozniak, Krzysztof; Linczuk, Maciej

2015-09-01

This paper presents a python to VHDL compiler. The compiler interprets an algorithmic description of a desired behavior written in Python and translate it to VHDL. FPGA combines many benefits of both software and ASIC implementations. Like software, the programmed circuit is flexible, and can be reconfigured over the lifetime of the system. FPGAs have the potential to achieve far greater performance than software as a result of bypassing the fetch-decode-execute operations of traditional processors, and possibly exploiting a greater level of parallelism. This can be achieved by using many computational resources at the same time. Creating parallel programs implemented in FPGAs in pure HDL is difficult and time consuming. Using higher level of abstraction and High-Level Synthesis compiler implementation time can be reduced. The compiler has been implemented using the Python language. This article describes design, implementation and results of created tools.

Performance of a 100V Half-Bridge MOSFET Driver, Type MIC4103, Over a Wide Temperature Range

NASA Technical Reports Server (NTRS)

Patterson, Richard L.; Hammoud, Ahmad

2011-01-01

The operation of a high frequency, high voltage MOSFET (metal-oxide semiconductor field-effect transistors) driver was investigated over a wide temperature regime that extended beyond its specified range. The Micrel MIC4103 is a 100V, non-inverting, dual driver that is designed to independently drive both high-side and low-side N-channel MOSFETs. It features fast propagation delay times and can drive 1000 pF load with 10ns rise times and 6 ns fall times [1]. The device consumes very little power, has supply under-voltage protection, and is rated for a -40 C to +125 C junction temperature range. The floating high-side driver of the chip can sustain boost voltages up to 100 V. Table I shows some of the device manufacturer s specification.

JPRS Report, East Europe

DTIC Science & Technology

1988-03-09

food , and the development of high quality public eating establishments. One must add that in recent years consumer goods cooperatives have taken...their planned tasks—establishing direct relationships , the usual foreign trade operations, purchase of licenses, etc. The introduction of new...service in the consumer goods sector. Indeed, this figure can hide poor management, closed sales outlets and restaurants , and sales people who work

16 CFR 1145.17 - Multi-purpose lighters that can be operated by children; risks of death or injury.

Code of Federal Regulations, 2010 CFR

2010-01-01

... by children; risks of death or injury. 1145.17 Section 1145.17 Commercial Practices CONSUMER PRODUCT...; risks of death or injury. (a) The Commission finds that it is in the public interest to regulate under the Consumer Product Safety Act any risks of injury associated with the fact that multi-purpose...

Lights Out: Foreseeable Catastrophic Effects of Geomagnetic Storms on the North American Power Grid and How to Mitigate Them

DTIC Science & Technology

2011-08-21

poultry, pork , beef, fish, and other meat products also are typically automated operations, done on electrically driven processing lines. 53 Food ...Infrastructure ..................................................... 18 Power Outage Impact on Consumables ( Food , Water, Medication...transportation, consumables ( food , water, and medication), and emergency services, are so highly dependent on reliable power supply from the grid, a

Banking: One of a Series for Expanded Programs in Consumer Education.

ERIC Educational Resources Information Center

Idleman, Hillis K., Ed.

The publication was produced in cooperation with the New York State Banking Department and is intended primarily as a teaching module to introduce high school students to how banks operate and how consumers can make best use of a bank's services. There is no assumption of prior banking experience or knowledge. In addition to some brief notes to…

Mobile Agents for Battlespace Information Exchange

DTIC Science & Technology

2013-05-01

autonomously gather information and coordinate activities (e.g. meetings, e - commerce transactions) on behalf of their owners. Sometime in the...operations where consumer -level infrastructure is not available. The report provides an overview of MA characteristics and follows with a description of...detection for security, telecommunications and the military. With the advent of broadband communication (fixed and wireless) a typical consumer is now

On Motivating Operations at the Point of Online Purchase Setting

ERIC Educational Resources Information Center

Fagerstrom, Asle; Arntzen, Erik

2013-01-01

Consumer behavior analysis can be applied over a wide range of economic topics in which the main focus is the contingencies that influence the behavior of the economic agent. This paper provides an overview on the work that has been done on the impact from motivating operations at the point of online purchase situation. Motivating operations, a…

The STD Site Operator. Satellite Technology Demonstration, Technical Report No. 0419.

ERIC Educational Resources Information Center

Braunstein, Jean

Intimately involved in any equipment system is the human factor. The people operating the equipment at the remote installations for the Satellite Technology Demonstration (STD) were different from paid employees or from private consumers. The STD site operators were paid only token fees; thus, they are best describd as having been motivated by the…

16 CFR 1115.14 - Time computations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS SUBSTANTIAL... spend a reasonable time for investigation and evaluation. (See § 1115.14(d).) (d) Time for investigation and evaluation. A subject firm may conduct a reasonably expeditious investigation in order to evaluate...

Integrating consumer engagement in health and medical research - an Australian framework.

PubMed

Miller, Caroline L; Mott, Kathy; Cousins, Michael; Miller, Stephanie; Johnson, Anne; Lawson, Tony; Wesselingh, Steve

2017-02-10

Quality practice of consumer engagement is still in its infancy in many sectors of medical research. The South Australian Health and Medical Research Institute (SAHMRI) identified, early in its development, the opportunity to integrate evidence-driven consumer and community engagement into its operations. SAHMRI partnered with Health Consumers Alliance and consumers in evidence generation. A Partnership Steering Committee of researchers and consumers was formed for the project. An iterative mixed-method qualitative process was used to generate a framework for consumer engagement. This process included a literature review followed by semi-structured interviews with experts in consumer engagement and lead medical researchers, group discussions and a consensus workshop with the Partnership Steering Committee, facilitated by Health Consumer Alliance. The literature revealed a dearth of evidence about effective consumer engagement methodologies. Four organisational dimensions are reported to contribute to success, namely governance, infrastructure, capacity and advocacy. Key themes identified through the stakeholder interviews included sustained leadership, tangible benefits, engagement strategies should be varied, resourcing, a moral dimension, and challenges. The consensus workshop produced a framework and tangible strategies. Comprehensive examples of consumer participation in health and medical research are limited. There are few documented studies of what techniques are effective. This evidence-driven framework, developed in collaboration with consumers, is being integrated in a health and medical research institute with diverse programs of research. This framework is offered as a contribution to the evidence base around meaningful consumer engagement and as a template for other research institutions to utilise.

FBC: a flat binary code scheme for fast Manhattan hash retrieval

NASA Astrophysics Data System (ADS)

Kong, Yan; Wu, Fuzhang; Gao, Lifa; Wu, Yanjun

2018-04-01

Hash coding is a widely used technique in approximate nearest neighbor (ANN) search, especially in document search and multimedia (such as image and video) retrieval. Based on the difference of distance measurement, hash methods are generally classified into two categories: Hamming hashing and Manhattan hashing. Benefitting from better neighborhood structure preservation, Manhattan hashing methods outperform earlier methods in search effectiveness. However, due to using decimal arithmetic operations instead of bit operations, Manhattan hashing becomes a more time-consuming process, which significantly decreases the whole search efficiency. To solve this problem, we present an intuitive hash scheme which uses Flat Binary Code (FBC) to encode the data points. As a result, the decimal arithmetic used in previous Manhattan hashing can be replaced by more efficient XOR operator. The final experiments show that with a reasonable memory space growth, our FBC speeds up more than 80% averagely without any search accuracy loss when comparing to the state-of-art Manhattan hashing methods.

Increasingly automated procedure acquisition in dynamic systems

NASA Technical Reports Server (NTRS)

Mathe, Nathalie; Kedar, Smadar

1992-01-01

Procedures are widely used by operators for controlling complex dynamic systems. Currently, most development of such procedures is done manually, consuming a large amount of paper, time, and manpower in the process. While automated knowledge acquisition is an active field of research, not much attention has been paid to the problem of computer-assisted acquisition and refinement of complex procedures for dynamic systems. The Procedure Acquisition for Reactive Control Assistant (PARC), which is designed to assist users in more systematically and automatically encoding and refining complex procedures. PARC is able to elicit knowledge interactively from the user during operation of the dynamic system. We categorize procedure refinement into two stages: diagnosis - diagnose the failure and choose a repair - and repair - plan and perform the repair. The basic approach taken in PARC is to assist the user in all steps of this process by providing increased levels of assistance with layered tools. We illustrate the operation of PARC in refining procedures for the control of a robot arm.

Considerations for Architecture Level Trade Studies for Environmental Sensors

NASA Technical Reports Server (NTRS)

Peterson, Craig

2010-01-01

Comparisons of key characteristics of environmental sensors such as technology readiness levels, mass, power, volume, and detection capabilities are essential for initial trade studies to determine likely candidates for further development and evaluation. However, these trade studies only provide part of the information necessary to make selection decisions. Ultimately, the sensors must be judged based on the overall system architectures and operational scenarios for which they are intended. This means that additional characteristics, such as architectural needs for redundancy, operational lifetime, ability to maintain calibration, and repair and replacement strategies, among others, must also be considered. Given that these characteristics can be extremely time-consuming and costly to obtain, careful planning is essential to minimize the effort involved. In this paper, an approach is explored for determining an effective yet comprehensive set of architecture level trades which is minimally impacted by the inevitable changes in operational (mission) scenarios. The approach will also identify and integrate the various facilities and opportunities required to obtain the desired architecture level trade information.

PVDaCS - A prototype knowledge-based expert system for certification of spacecraft data

NASA Technical Reports Server (NTRS)

Wharton, Cathleen; Shiroma, Patricia J.; Simmons, Karen E.

1989-01-01

On-line data management techniques to certify spacecraft information are mandated by increasing telemetry rates. Knowledge-based expert systems offer the ability to certify data electronically without the need for time-consuming human interaction. Issues of automatic certification are explored by designing a knowledge-based expert system to certify data from a scientific instrument, the Orbiter Ultraviolet Spectrometer, on an operating NASA planetary spacecraft, Pioneer Venus. The resulting rule-based system, called PVDaCS (Pioneer Venus Data Certification System), is a functional prototype demonstrating the concepts of a larger system design. A key element of the system design is the representation of an expert's knowledge through the usage of well ordered sequences. PVDaCS produces a certification value derived from expert knowledge and an analysis of the instrument's operation. Results of system performance are presented.

Liquid chromatography-tandem mass spectrometry characterization of five new leucinostatins produced by Paecilomyces lilacinus CG-189.

PubMed

Martinez, Ana Flávia Canovas; Moraes, Luiz Alberto Beraldo

2015-03-01

The fungus Paecilomyces lilacinus produces leucinostatins—peptaibiotics that exert a range of biological activities including antimalarial, antiviral, antitumor and phytotoxicity. In this paper, we developed an analytical method employing LC-MS/MS in the precursor ion and product ion scan modes to elucidate five new leucinostatins. Direct Infusion (DI-MS) helped to identify the most abundant leucinostatins: F, D B2, S, A and K. MS/MS analysis using a triple quadrupole operating at different scan modes is a versatile tool to study natural products, especially peptaibiotics. Although DI-MS full-scan analysis is rapid and sensitive, it cannot distinguish between peptide isomers. On the other hand, LC-MS/MS operated in the precursor ion and product ion modes is time consuming, but allows identifying the structure of isomers or isobar in crude extracts.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong Sun Lee; Yu Ryang Pyun

A food drying process in a tunnel dryer was modeled from Keey's drying model and experimental drying curve, and optimized in operating conditions consisting of inlet air temperature, air recycle ratio and air flow rate. Radish was chosen as a typical food material to be dried, because it has the typical drying characteristics of food and quality indexes of ascorbic acid destruction and browning during drying. Optimization results of cocurrent and counter current tunnel drying showed higher inlet air temperature, lower recycle ratio and higher air flow rate with shorter total drying time. Compared with cocurrent operation counter current dryingmore » used lower air temperature, lower recycle ratio and lower air flow rate, and appeared to be more efficient in energy usage. Most of consumed energy was shown to be used for sir heating and then escaped from the dryer in the form of exhaust air.« less

Cassini Attitude Control Operations Flight Rules and How They are Enforced

NASA Technical Reports Server (NTRS)

Burk, Thomas; Bates, David

2008-01-01

The Cassini spacecraft was launched on October 15, 1997 and arrived at Saturn on June 30, 2004. It has performed detailed observations and remote sensing of Saturn, its rings, and its satellites since that time. Cassini deployed the European-built Huygens probe which descended through the Titan atmosphere and landed on its surface on January 14, 2005. Operating the Cassini spacecraft is a complex scientific, engineering, and management job. In order to safely operate the spacecraft, a large number of flight rules were developed. These flight rules must be enforced throughout the lifetime of the Cassini spacecraft. Flight rules are defined as any operational limitation imposed by the spacecraft system design, hardware, and software, violation of which would result in spacecraft damage, loss of consumables, loss of mission objectives, loss and/or degradation of science, and less than optimal performance. Flight rules require clear description and rationale. Detailed automated methods have been developed to insure the spacecraft is continuously operated within these flight rules. An overview of all the flight rules allocated to the Cassini Attitude Control and Articulation Subsystem and how they are enforced is presented in this paper.

Community air monitoring and the Village Green Project ...

EPA Pesticide Factsheets

Cost and logistics are practical issues that have historically constrained the number of locations where long-term, active air pollution measurement is possible. In addition, traditional air monitoring approaches are generally conducted by technical experts with limited engagement with community members. EPA’s Village Green Project (VGP) is a prototype technology designed to add value to a community environment – VGP is a park bench equipped with air and meteorological instruments that measure ozone, fine particles, wind, temperature, and humidity at a one-minute time resolution, with the open-source Arduino microprocessor operating as the system controller. The data are streamed wirelessly to a database, passed through automatic diagnostic quality checks, and then made publically available on an engaging website. The station was designed to minimize power use; it consumes an estimated 15W and operates entirely on solar power, is engineered to run for several days with minimal solar radiation, and is capable of automatically shutting down components of the system to conserve power and restarting when power availability increases. Situated outside a public library in Durham, North Carolina, VGP has also been a gathering location for air quality experts to engage with community members. During the time span of June, 2013 through January, 2014, the station collected about 3500 hours of ozone and PM2.5 data, with over 90% up-time operating only on solar po

Controversy of hand-assisted laparoscopic colorectal surgery

PubMed Central

Meshikhes, Abdul-Wahed Nasir

2010-01-01

Laparoscopically assisted colorectal procedures are time-consuming and technically demanding and hence have a long steep learning curve. In the technical demand, surgeons need to handle a long mobile organ, the colon, and have to operate on multiple abdominal quadrants, most of the time with the need to secure multiple mesenteric vessels. Therefore, a new surgical innovation called hand-assisted laparoscopic surgery (HALS) was introduced in the mid 1990s as a useful alternative to totally laparoscopic procedures. This hybrid operation allows the surgeon to introduce the non-dominant hand into the abdominal cavity through a special hand port while maintaining the pneumoperitoneum. A hand in the abdomen can restore the tactile sensation which is usually lacking in laparoscopic procedures. It also improves the eye-to-hand coordination, allows the hand to be used for blunt dissection or retraction and also permits rapid control of unexpected bleeding. All of those factors can contribute tremendously to reducing the operative time. Moreover, this procedure is also considered as a hybrid procedure that combines the advantages of both minimally invasive and conventional open surgery. Nevertheless, the exact role of HALS in colorectal surgery has not been well defined during the advanced totally laparoscopic procedures. This article reviews the current status of hand-assisted laparoscopic colorectal surgery as a minimally invasive procedure in the era of laparoscopic surgery. PMID:21128315

Operations research methods improve chemotherapy patient appointment scheduling.

PubMed

Santibáñez, Pablo; Aristizabal, Ruben; Puterman, Martin L; Chow, Vincent S; Huang, Wenhai; Kollmannsberger, Christian; Nordin, Travis; Runzer, Nancy; Tyldesley, Scott

2012-12-01

Clinical complexity, scheduling restrictions, and outdated manual booking processes resulted in frequent clerical rework, long waitlists for treatment, and late appointment notification for patients at a chemotherapy clinic in a large cancer center in British Columbia, Canada. A 17-month study was conducted to address booking, scheduling and workload issues and to develop, implement, and evaluate solutions. A review of scheduling practices included process observation and mapping, analysis of historical appointment data, creation of a new performance metric (final appointment notification lead time), and a baseline patient satisfaction survey. Process improvement involved discrete event simulation to evaluate alternative booking practice scenarios, development of an optimization-based scheduling tool to improve scheduling efficiency, and change management for implementation of process changes. Results were evaluated through analysis of appointment data, a follow-up patient survey, and staff surveys. Process review revealed a two-stage scheduling process. Long waitlists and late notification resulted from an inflexible first-stage process. The second-stage process was time consuming and tedious. After a revised, more flexible first-stage process and an automated second-stage process were implemented, the median percentage of appointments exceeding the final appointment notification lead time target of one week was reduced by 57% and median waitlist size decreased by 83%. Patient surveys confirmed increased satisfaction while staff feedback reported reduced stress levels. Significant operational improvements can be achieved through process redesign combined with operations research methods.

Making Space for Consuming Practices

ERIC Educational Resources Information Center

Rooney, Donna; Manidis, Marie; Scheeres, Hermine

2016-01-01

This empirically driven paper is about workplace learning with specific focus on the "work" of "consuming practices." By "consuming" we refer to the eating, and the drinking, and (at times) to the smoking that workers, in most organisations, do on a daily basis. Indeed, it is the quotidian nature of consuming, coupled…

Strategies to Increase Behavior-Specific Teacher Praise in an Inclusive Environment

ERIC Educational Resources Information Center

Musti-Rao, Shobana; Haydon, Todd

2011-01-01

Managing students' disruptive behavior in the classroom can be a time-consuming task and greatly reduces the amount of time teachers spend on instruction. Although there are several research-validated classroom management strategies, teachers are more likely to adopt strategies that are less time-consuming than strategies that take more time or…

Crew Health and Performance Improvements with Reduced Carbon Dioxide Levels and the Resource Impact to Accomplish Those Reductions

NASA Technical Reports Server (NTRS)

James, John T.; Meyers, Valerie E.; Sipes, Walter; Scully, Robert R.; Matty, Christopher M.

2011-01-01

Carbon dioxide (CO2) removal is one of the primary functions of the International Space Station (ISS) atmosphere revitalization systems. Primary CO2 removal is via the ISS s two Carbon Dioxide Removal Assemblies (CDRAs) and the Russian carbon dioxide removal assembly (Vozdukh); both of these systems are regenerable, meaning that their CO2 removal capacity theoretically remains constant as long as the system is operating. Contingency CO2 removal capability is provided by lithium hydroxide (LiOH) canisters, which are consumable, meaning that their CO2 removal capability disappears once the resource is used. With the advent of 6 crew ISS operations, experience showing that CDRA failures are not uncommon, and anecdotal association of crew symptoms with CO2 values just above 4 mmHg, the question arises: How much lower do we keep CO2 levels to minimize the risk to crew health and performance, and what will the operational cost to the CDRAs be to do it? The primary crew health concerns center on the interaction of increased intracranial pressure from fluid shifts and the increased intracranial blood flow induced by CO2. Typical acute symptoms include headache, minor visual disturbances, and subtle behavioral changes. The historical database of CO2 exposures since the beginning of ISS operations has been compared to the incidence of crew symptoms reported in private medical conferences. We have used this database in an attempt to establish an association between the CO2 levels and the risk of crew symptoms. This comparison will answer the question of the level needed to protect the crew from acute effects. As for the second part of the question, operation of the ISS s regenerable CO2 removal capability reduces the limited life of constituent parts. It also consumes limited electrical power and thermal control resources. Operation of consumable CO2 removal capability (LiOH) uses finite consumable materials, which must be replenished in the long term. Therefore, increased CO2 removal means increased resource use, with increased logistical capability to maintain necessary resources on board ISS. We must strike a balance between sufficiently low CO2 levels to maintain crew health and CO2 levels which are operationally feasible for the ISS program

Grid integration and smart grid implementation of emerging technologies in electric power systems through approximate dynamic programming

NASA Astrophysics Data System (ADS)

Xiao, Jingjie

A key hurdle for implementing real-time pricing of electricity is a lack of consumers' responses. Solutions to overcome the hurdle include the energy management system that automatically optimizes household appliance usage such as plug-in hybrid electric vehicle charging (and discharging with vehicle-to-grid) via a two-way communication with the grid. Real-time pricing, combined with household automation devices, has a potential to accommodate an increasing penetration of plug-in hybrid electric vehicles. In addition, the intelligent energy controller on the consumer-side can help increase the utilization rate of the intermittent renewable resource, as the demand can be managed to match the output profile of renewables, thus making the intermittent resource such as wind and solar more economically competitive in the long run. One of the main goals of this dissertation is to present how real-time retail pricing, aided by control automation devices, can be integrated into the wholesale electricity market under various uncertainties through approximate dynamic programming. What distinguishes this study from the existing work in the literature is that whole- sale electricity prices are endogenously determined as we solve a system operator's economic dispatch problem on an hourly basis over the entire optimization horizon. This modeling and algorithm framework will allow a feedback loop between electricity prices and electricity consumption to be fully captured. While we are interested in a near-optimal solution using approximate dynamic programming; deterministic linear programming benchmarks are use to demonstrate the quality of our solutions. The other goal of the dissertation is to use this framework to provide numerical evidence to the debate on whether real-time pricing is superior than the current flat rate structure in terms of both economic and environmental impacts. For this purpose, the modeling and algorithm framework is tested on a large-scale test case with hundreds of power plants based on data available for California, making our findings useful for policy makers, system operators and utility companies to gain a concrete understanding on the scale of the impact with real-time pricing.

A qualitative evaluation of New Zealand consumers perceptions of general practice nurses

PubMed Central

2013-01-01

Background An important consideration in health service delivery is ensuring that services meet consumer needs and that consumers are satisfied with service delivery. Patient satisfaction can impact on compliance with suggested treatments and therefore impact on health outcomes. Comparatively few studies have explored consumer satisfaction with nurses in general practice. Methods A sub-group of 18 consumers from a larger quantitative evaluation of consumer satisfaction with New Zealand general practice nurses participated in semi-structured telephone interviews. Interview data was analysed using thematic analysis. Results Four major themes emerged from the data. These themes highlighted that, despite confusion experienced by some consumers regarding the practice nurse role, consumers were happy with the level of care provided by them. Consumers felt valued by Practice Nurses and considered them competent and highly knowledgeable. Findings also convey that consumers appreciate the accessibility and financial benefits of utilising the services of practice nurses. Conclusions Consumers are highly satisfied with practice nurse service delivery and value their relationships with these health professionals. Consumers revealed that greater clarity around the practice nurse role and their scope of practice may enhance their utilisation. Spreading the message of practice nurses being the right person to deliver care, within their scope of practice, at the right time may have the potential to provide more timely care within the primary care setting. PMID:23433311

Consumption patterns of sweet drinks in a population of Australian children and adolescents (2003-2008).

PubMed

Jensen, Britt W; Nichols, Melanie; Allender, Steven; de Silva-Sanigorski, Andrea; Millar, Lynne; Kremer, Peter; Lacy, Kathleen; Swinburn, Boyd

2012-09-12

Intake of sweet drinks has previously been associated with the development of overweight and obesity among children and adolescents. The present study aimed to assess the consumption pattern of sweet drinks in a population of children and adolescents in Victoria, Australia. Data on 1,604 children and adolescents (4-18 years) from the comparison groups of two quasi-experimental intervention studies from Victoria, Australia were analysed. Sweet drink consumption (soft drink and fruit juice/cordial) was assessed as one day's intake and typical intake over the last week or month at two time points between 2003 and 2008 (mean time between measurement: 2.2 years). Assessed using dietary recalls, more than 70% of the children and adolescents consumed sweet drinks, with no difference between age groups (p = 0.28). The median intake among consumers was 500 ml and almost a third consumed more than 750 ml per day. More children and adolescents consumed fruit juice/cordial (69%) than soft drink (33%) (p < 0.0001) and in larger volumes (median intake fruit juice/cordial: 500 ml and soft drink: 375 ml). Secular changes in sweet drink consumption were observed with a lower proportion of children and adolescents consuming sweet drinks at time 2 compared to time 1 (significant for age group 8 to <10 years, p = 0.001). The proportion of Australian children and adolescents from the state of Victoria consuming sweet drinks has been stable or decreasing, although a high proportion of this sample consumed sweet drinks, especially fruit juice/cordial at both time points.

Use of New Commercial, Off-the-Shelf, High-Definition Structure Scanning Fathometer/Depth Finder For Coastal Current Survey Operations

NASA Astrophysics Data System (ADS)

Roggenstein, E. B.; Gray, G.

2013-12-01

The National Oceanic and Atmospheric Administration (NOAA) National Ocean Service (NOS) Center for Operational Oceanographic Products and Services (COOPS) manages three national observing system programs. These are the National Water level Observation Network (NWLON) (210 stations), the 23 NOAA/Physical Oceanographic Real-Time Systems (PORTS), and National Currents Observing Program (NCOP) (approximately 70 deployments/year). In support of its mission COOPS operates and maintains a number of small boats. During vessel operations, side-scan sonar data are at times needed to provide information about bottom structure for future work in the area. For example, potential hazards, obstructions, or bottom morphology features that have not been identified on localized charts for a given area could be used to inform decisions on planned installations. Side-scan sonar capability is also important when attempting to reacquire bottom mounts that fail to surface at the conclusion of a current meter survey. Structure mapping and side-scan capabilities have been added to recent consumer-level, commercial, off-the-shelf fathometers, generally intended for recreational, commercial fishing, and diving applications. We are proposing to investigate these systems' viability for meeting survey requirements. We assess their ability to provide a flexible alternative to research/commercial oceanographic level side-scan system at a significant cost savings. Such systems could provide important information to support scientific missions that require qualitative seafloor imagery.

Data-Mining Toolset Developed for Determining Turbine Engine Part Life Consumption

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.

2003-01-01

The current practice in aerospace turbine engine maintenance is to remove components defined as life-limited parts after a fixed time, on the basis of a predetermined number of flight cycles. Under this schedule-based maintenance practice, the worst-case usage scenario is used to determine the usable life of the component. As shown, this practice often requires removing a part before its useful life is fully consumed, thus leading to higher maintenance cost. To address this issue, the NASA Glenn Research Center, in a collaborative effort with Pratt & Whitney, has developed a generic modular toolset that uses data-mining technology to parameterize life usage models for maintenance purposes. The toolset enables a "condition-based" maintenance approach, where parts are removed on the basis of the cumulative history of the severity of operation they have experienced. The toolset uses data-mining technology to tune life-consumption models on the basis of operating and maintenance histories. The flight operating conditions, represented by measured variables within the engine, are correlated with repair records for the engines, generating a relationship between the operating condition of the part and its service life. As shown, with the condition-based maintenance approach, the lifelimited part is in service until its usable life is fully consumed. This approach will lower maintenance costs while maintaining the safety of the propulsion system. The toolset is a modular program that is easily customizable by users. First, appropriate parametric damage accumulation models, which will be functions of engine variables, must be defined. The tool then optimizes the models to match the historical data by computing an effective-cycle metric that reduces the unexplained variability in component life due to each damage mode by accounting for the variability in operational severity. The damage increment due to operating conditions experienced during each flight is used to compute the effective cycles and ultimately the replacement time. Utilities to handle data problems, such as gaps in the flight data records, are included in the toolset. The tool was demonstrated using the first stage, high-pressure turbine blade of the PW4077 engine (Pratt & Whitney, East Hartford, CT). The damage modes considered were thermomechanical fatigue and oxidation/erosion. Each PW4077 engine contains 82 first-stage, high-pressure turbine blades, and data from a fleet of engines were used to tune the life-consumption models. The models took into account not only measured variables within the engine, but also unmeasured variables such as engine health parameters that are affected by degradation of the engine due to aging. The tool proved effective at predicting the average number of blades scrapped over time due to each damage mode, per engine, given the operating history of the engine. The customizable tools are available to interested parties within the aerospace community.

Predicting Employment Outcomes of Consumers of State-Operated Comprehensive Rehabilitation Centers

ERIC Educational Resources Information Center

Beach, David Thomas

2009-01-01

This study used records from a state-operated comprehensive rehabilitation center to investigate possible predictive factors related to completing comprehensive rehabilitation center programs and successful vocational rehabilitation (VR) case closure. An analysis of demographic data of randomly selected comprehensive rehabilitation center…

Advances in dust cyclone research

USDA-ARS?s Scientific Manuscript database

Dust cyclones reduce particulate emissions but their operation consumes electrical energy. Response surface methodology was used to compare two strategies to reduce energy costs without increasing emissions. Cyclones of a standard design (1D3D) were operated singly and in series, as was an ‘Experi...

Real Time Intraoperative Monitoring of Blood Loss with a Novel Tablet Application.

PubMed

Sharareh, Behnam; Woolwine, Spencer; Satish, Siddarth; Abraham, Peter; Schwarzkopf, Ran

2015-01-01

Real-time monitoring of blood loss is critical in fluid management. Visual estimation remains the standard of care in estimating blood loss, yet is demonstrably inaccurate. Photometric analysis, which is the referenced "gold-standard" for measuring blood loss, is both time-consuming and costly. The purpose of this study was to evaluate the efficacy of a novel tablet-monitoring device for measurement of Hb loss during orthopaedic procedures. This is a prospective study of 50 patients in a consecutive series of joint arthroplasty cases. The novel System with Feature Extraction Technology was used to measure the amount of Hb contained within surgical sponges intra-operatively. The system's measures were then compared with those obtained via gravimetric method and photometric analysis. Accuracy was evaluated using linear regression and Bland-Altman analysis. Our results showed a significant positive correlation between Triton tablet system and photometric analysis with respect to intra-operative hemoglobin and blood loss at 0.92 and 0.91, respectively. This novel system can accurately determine Hb loss contained within surgical sponges. We believe that this user-friendly software can be used for measurement of total intraoperative blood loss and thus aid in a more accurate fluid management protocols during orthopaedic surgical procedures.

Sideband Algorithm for Automatic Wind Turbine Gearbox Fault Detection and Diagnosis: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zappala, D.; Tavner, P.; Crabtree, C.

2013-01-01

Improving the availability of wind turbines (WT) is critical to minimize the cost of wind energy, especially for offshore installations. As gearbox downtime has a significant impact on WT availabilities, the development of reliable and cost-effective gearbox condition monitoring systems (CMS) is of great concern to the wind industry. Timely detection and diagnosis of developing gear defects within a gearbox is an essential part of minimizing unplanned downtime of wind turbines. Monitoring signals from WT gearboxes are highly non-stationary as turbine load and speed vary continuously with time. Time-consuming and costly manual handling of large amounts of monitoring data representmore » one of the main limitations of most current CMSs, so automated algorithms are required. This paper presents a fault detection algorithm for incorporation into a commercial CMS for automatic gear fault detection and diagnosis. The algorithm allowed the assessment of gear fault severity by tracking progressive tooth gear damage during variable speed and load operating conditions of the test rig. Results show that the proposed technique proves efficient and reliable for detecting gear damage. Once implemented into WT CMSs, this algorithm can automate data interpretation reducing the quantity of information that WT operators must handle.« less

Usefulness of Deep Hypothermic Circulatory Arrest and Regional Cerebral Perfusion in Children

PubMed Central

Guo, Zheng; Hu, Ren-Jie; Zhu, De-Ming; Zhu, Zhong-Qun; Zhang, Hai-Bo

2013-01-01

To compare the safety and usefulness of deep hypothermic circulatory arrest (DHCA) and regional cerebral perfusion (RCP) during pediatric open heart surgery. Between January 1, 2004 and September 30, 2012, 1250 children with congenital cardiac defect underwent corrective operation with the DHCA or RCP technique in the Shanghai Children's Medical Center. Of them, 947 cases underwent the operation with the aid of DHCA (DHCA group), and 303 cases with RCP (RCP group). The mean DHCA time was 30.64±15.81 (7–63) minutes and mean RCP time was 36.18±12.86 (10–82) minutes. The mortality rate was 7.18% (68/947) and 6.60% (20/30) in two groups, respectively. The postoperative incidences of temporary and permanent neurological dysfunction were 6.23% (59/947) in the DHCA group and 2.64% (8/303) in the RCP group (p<0.01). The incidence of other complications such as low cardiac output, renal dysfunction, and lung issues are similar in both groups. RCP is a reliable technique for cerebral protection and it facilitates time-consuming corrected procedures for complex congenital cardiac defect repair procedures. PMID:24066266

Swarm satellite mission scheduling & planning using Hybrid Dynamic Mutation Genetic Algorithm

NASA Astrophysics Data System (ADS)

Zheng, Zixuan; Guo, Jian; Gill, Eberhard

2017-08-01

Space missions have traditionally been controlled by operators from a mission control center. Given the increasing number of satellites for some space missions, generating a command list for multiple satellites can be time-consuming and inefficient. Developing multi-satellite, onboard mission scheduling & planning techniques is, therefore, a key research field for future space mission operations. In this paper, an improved Genetic Algorithm (GA) using a new mutation strategy is proposed as a mission scheduling algorithm. This new mutation strategy, called Hybrid Dynamic Mutation (HDM), combines the advantages of both dynamic mutation strategy and adaptive mutation strategy, overcoming weaknesses such as early convergence and long computing time, which helps standard GA to be more efficient and accurate in dealing with complex missions. HDM-GA shows excellent performance in solving both unconstrained and constrained test functions. The experiments of using HDM-GA to simulate a multi-satellite, mission scheduling problem demonstrates that both the computation time and success rate mission requirements can be met. The results of a comparative test between HDM-GA and three other mutation strategies also show that HDM has outstanding performance in terms of speed and reliability.

Ion thruster system (8-cm) cyclic endurance test

NASA Technical Reports Server (NTRS)

Dulgeroff, C. R.; Beattie, J. R.; Poeschel, R. L.; Hyman, J., Jr.

1984-01-01

This report describes the qualification test of an Engineering-Model 5-mN-thrust 8-cm-diameter mercury ion thruster which is representative of the Ion Auxiliary Propulsion System (IAPS) thrusters. Two of these thrusters are scheduled for future flight test. The cyclic endurance test described herein was a ground-based test performed in a vacuum facility with a liquid-nitrogen-cooled cryo-surface and a frozen mercury target. The Power Electronics Unit, Beam Shield, Gimal, and Propellant Tank that were used with the thruster in the endurance test are also similar to those of the IAPS. The IAPS thruster that will undergo the longest beam-on-time during the actual space test will be subjected to 7,055 hours of beam-on-time and 2,557 cycles during the flight test. The endurance test was successfully concluded when the mercury in the IAPS Propellant Tank was consumed. At that time, 8,471 hours of beam-on-time and 599 cycles had been accumulated. Subsequent post-test-evaluation operations were performed (without breaking vacuum) which extended the test values to 652 cycles and 9,489 hours of beam-on-time. The Power Electronic Unit (PEU) and thruster were in the same vacuum chamber throughout the test. The PEU accumulated 10,268 hr of test time with high voltage applied to the operating thruster or dummy load.

Lunar Surface Architecture Utilization and Logistics Support Assessment

NASA Astrophysics Data System (ADS)

Bienhoff, Dallas; Findiesen, William; Bayer, Martin; Born, Andrew; McCormick, David

2008-01-01

Crew and equipment utilization and logistics support needs for the point of departure lunar outpost as presented by the NASA Lunar Architecture Team (LAT) and alternative surface architectures were assessed for the first ten years of operation. The lunar surface architectures were evaluated and manifests created for each mission. Distances between Lunar Surface Access Module (LSAM) landing sites and emplacement locations were estimated. Physical characteristics were assigned to each surface element and operational characteristics were assigned to each surface mobility element. Stochastic analysis was conducted to assess probable times to deploy surface elements, conduct exploration excursions, and perform defined crew activities. Crew time is divided into Outpost-related, exploration and science, overhead, and personal activities. Outpost-related time includes element deployment, EVA maintenance, IVA maintenance, and logistics resupply. Exploration and science activities include mapping, geological surveys, science experiment deployment, sample analysis and categorizing, and physiological and biological tests in the lunar environment. Personal activities include sleeping, eating, hygiene, exercising, and time off. Overhead activities include precursor or close-out tasks that must be accomplished but don't fit into the other three categories such as: suit donning and doffing, airlock cycle time, suit cleaning, suit maintenance, post-landing safing actions, and pre-departure preparations. Equipment usage time, spares, maintenance actions, and Outpost consumables are also estimated to provide input into logistics support planning. Results are normalized relative to the NASA LAT point of departure lunar surface architecture.

Cognitive patterns: giving autonomy some context

NASA Astrophysics Data System (ADS)

Dumond, Danielle; Stacy, Webb; Geyer, Alexandra; Rousseau, Jeffrey; Therrien, Mike

2013-05-01

Today's robots require a great deal of control and supervision, and are unable to intelligently respond to unanticipated and novel situations. Interactions between an operator and even a single robot take place exclusively at a very low, detailed level, in part because no contextual information about a situation is conveyed or utilized to make the interaction more effective and less time consuming. Moreover, the robot control and sensing systems do not learn from experience and, therefore, do not become better with time or apply previous knowledge to new situations. With multi-robot teams, human operators, in addition to managing the low-level details of navigation and sensor management while operating single robots, are also required to manage inter-robot interactions. To make the most use of robots in combat environments, it will be necessary to have the capability to assign them new missions (including providing them context information), and to have them report information about the environment they encounter as they proceed with their mission. The Cognitive Patterns Knowledge Generation system (CPKG) has the ability to connect to various knowledge-based models, multiple sensors, and to a human operator. The CPKG system comprises three major internal components: Pattern Generation, Perception/Action, and Adaptation, enabling it to create situationally-relevant abstract patterns, match sensory input to a suitable abstract pattern in a multilayered top-down/bottom-up fashion similar to the mechanisms used for visual perception in the brain, and generate new abstract patterns. The CPKG allows the operator to focus on things other than the operation of the robot(s).

Organizational capacity needs of consumer-run organizations.

PubMed

Wituk, Scott; Vu, Chi C; Brown, Louis D; Meissen, Greg

2008-05-01

Consumer-run organizations (CROs) are self-help oriented organizations that are run entirely by consumers (people who use or have used mental health services). The current study utilizes an organizational capacity framework to explore the needs of operating CROs. This framework includes four core capacity areas: (1) technical, (2) management, (3) leadership, and (4) adaptive capacity. An analysis reveals that the greatest organizational needs are related to technical and management capacities. Implications are discussed in terms of strategies and activities that CRO leaders and mental health professionals and administrators can use to strengthen the organizational capacity of CROs in their community.

Control of innovation activity in a competitive metallurgical business

NASA Astrophysics Data System (ADS)

Bogdanov, S. V.

2010-12-01

Certain competitive advantages of a manufacturer on a goods market can be provided if one creates conditions for bifurcation development of an innovation process in metallurgical business under conditions of market uncertainty of a demand for goods of a specified consumer quality and determines the technical-and-economic versions of stable operation of a production system for performing orders of metal product consumers.

United States Marine Corps Expeditionary Energy Strategy and Implementation Plan

DTIC Science & Technology

2011-02-01

Support System (NTCSS, OOMA/OIMA), and Aircraft Inventory Readiness and Reporting System (AIRRS) data in the Naval Aviation Logistics Data Analysis...Corps’ share is used for operational purposes—fuel for training, moving and sustaining our forces, aircraft and weapons platforms .1 Within this, and...this 75% was consumed by ‘ground forces,’ which includes use by vehicles, generators, and other sustainment equipment . Aircraft consumed

Beyond Enterprise Resource Planning (ERP): The Next Generation Enterprise Resource Planning Environment

DTIC Science & Technology

2012-02-01

Software as a Service ( SaaS )— SaaS solutions involve conforming an organization’s...consumer of the utilized service . Service Models Software as a Service ( SaaS ) The capability provided to the consumer is to use the provider’s...operating system, platforms, and software installed. In contrast, Software as a Service ( SaaS ) abstracts the entire stack except for a few

Determinants of reinforcer accumulation during an operant task.

PubMed

McFarland, J M; Lattal, K A

2001-11-01

Responses by rats on an earn lever made available food pellets that were delivered to a food cup by responses on a second, collect, lever. The rats could either collect and immediately consume or accumulate (defined as the percentage of multiple earn responses and as the number of pellets earned before a collect response) earned pellets. In Experiment 1, accumulation varied as a function of variations in the earn or collect response requirements and whether the earn and collect levers were proximal (31 cm) or distal (248 cm) to one another. Some accumulation occurred under all but one of the conditions, but generally was higher when the earn and collect levers were distal to one another, particularly when the earn response requirement was fixed-ratio (FR) 1. In Experiment 2, the contributions of responses and time to accumulation were assessed by comparing an FR 20 earn response requirement to a condition in which only a single earn response was required at the end of a time interval nominally yoked to the FR interval. When 248 cm separated the earn and collect levers, accumulation was always greater in the FR condition, and it was not systematically related to reinforcement rate. In Experiment 3, increasing the earn response requirement with a progressive-ratio schedule that reset only with a collect response increased the likelihood of accumulation when the collect and earn levers were 248 cm apart, even though such accumulation increased the next earn response requirement. Reinforcer accumulation is an understudied dimension of operant behavior that relates to the analysis of such phenomena as hoarding and self-control, in that they too involve accumulating versus immediately collecting or consuming reinforcers.

Determinants of reinforcer accumulation during an operant task.

PubMed Central

McFarland, J M; Lattal, K A

2001-01-01

Responses by rats on an earn lever made available food pellets that were delivered to a food cup by responses on a second, collect, lever. The rats could either collect and immediately consume or accumulate (defined as the percentage of multiple earn responses and as the number of pellets earned before a collect response) earned pellets. In Experiment 1, accumulation varied as a function of variations in the earn or collect response requirements and whether the earn and collect levers were proximal (31 cm) or distal (248 cm) to one another. Some accumulation occurred under all but one of the conditions, but generally was higher when the earn and collect levers were distal to one another, particularly when the earn response requirement was fixed-ratio (FR) 1. In Experiment 2, the contributions of responses and time to accumulation were assessed by comparing an FR 20 earn response requirement to a condition in which only a single earn response was required at the end of a time interval nominally yoked to the FR interval. When 248 cm separated the earn and collect levers, accumulation was always greater in the FR condition, and it was not systematically related to reinforcement rate. In Experiment 3, increasing the earn response requirement with a progressive-ratio schedule that reset only with a collect response increased the likelihood of accumulation when the collect and earn levers were 248 cm apart, even though such accumulation increased the next earn response requirement. Reinforcer accumulation is an understudied dimension of operant behavior that relates to the analysis of such phenomena as hoarding and self-control, in that they too involve accumulating versus immediately collecting or consuming reinforcers. PMID:11768714

Inspection of Pole-Like Structures Using a Visual-Inertial Aided VTOL Platform with Shared Autonomy

PubMed Central

Sa, Inkyu; Hrabar, Stefan; Corke, Peter

2015-01-01

This paper presents an algorithm and a system for vertical infrastructure inspection using a vertical take-off and landing (VTOL) unmanned aerial vehicle and shared autonomy. Inspecting vertical structures such as light and power distribution poles is a difficult task that is time-consuming, dangerous and expensive. Recently, micro VTOL platforms (i.e., quad-, hexa- and octa-rotors) have been rapidly gaining interest in research, military and even public domains. The unmanned, low-cost and VTOL properties of these platforms make them ideal for situations where inspection would otherwise be time-consuming and/or hazardous to humans. There are, however, challenges involved with developing such an inspection system, for example flying in close proximity to a target while maintaining a fixed stand-off distance from it, being immune to wind gusts and exchanging useful information with the remote user. To overcome these challenges, we require accurate and high-update rate state estimation and high performance controllers to be implemented onboard the vehicle. Ease of control and a live video feed are required for the human operator. We demonstrate a VTOL platform that can operate at close-quarters, whilst maintaining a safe stand-off distance and rejecting environmental disturbances. Two approaches are presented: Position-Based Visual Servoing (PBVS) using an Extended Kalman Filter (EKF) and estimator-free Image-Based Visual Servoing (IBVS). Both use monocular visual, inertia, and sonar data, allowing the approaches to be applied for indoor or GPS-impaired environments. We extensively compare the performances of PBVS and IBVS in terms of accuracy, robustness and computational costs. Results from simulations and indoor/outdoor (day and night) flight experiments demonstrate the system is able to successfully inspect and circumnavigate a vertical pole. PMID:26340631

High performance monolithic power management system with dynamic maximum power point tracking for microbial fuel cells.

PubMed

Erbay, Celal; Carreon-Bautista, Salvador; Sanchez-Sinencio, Edgar; Han, Arum

2014-12-02

Microbial fuel cell (MFC) that can directly generate electricity from organic waste or biomass is a promising renewable and clean technology. However, low power and low voltage output of MFCs typically do not allow directly operating most electrical applications, whether it is supplementing electricity to wastewater treatment plants or for powering autonomous wireless sensor networks. Power management systems (PMSs) can overcome this limitation by boosting the MFC output voltage and managing the power for maximum efficiency. We present a monolithic low-power-consuming PMS integrated circuit (IC) chip capable of dynamic maximum power point tracking (MPPT) to maximize the extracted power from MFCs, regardless of the power and voltage fluctuations from MFCs over time. The proposed PMS continuously detects the maximum power point (MPP) of the MFC and matches the load impedance of the PMS for maximum efficiency. The system also operates autonomously by directly drawing power from the MFC itself without any external power. The overall system efficiency, defined as the ratio between input energy from the MFC and output energy stored into the supercapacitor of the PMS, was 30%. As a demonstration, the PMS connected to a 240 mL two-chamber MFC (generating 0.4 V and 512 μW at MPP) successfully powered a wireless temperature sensor that requires a voltage of 2.5 V and consumes power of 85 mW each time it transmit the sensor data, and successfully transmitted a sensor reading every 7.5 min. The PMS also efficiently managed the power output of a lower-power producing MFC, demonstrating that the PMS works efficiently at various MFC power output level.

Sleep Disruption Medical Intervention Forecasting (SDMIF) Module for the Integrated Medical Model

NASA Technical Reports Server (NTRS)

Lewandowski, Beth; Brooker, John; Mallis, Melissa; Hursh, Steve; Caldwell, Lynn; Myers, Jerry

2011-01-01

The NASA Integrated Medical Model (IMM) assesses the risk, including likelihood and impact of occurrence, of all credible in-flight medical conditions. Fatigue due to sleep disruption is a condition that could lead to operational errors, potentially resulting in loss of mission or crew. Pharmacological consumables are mitigation strategies used to manage the risks associated with sleep deficits. The likelihood of medical intervention due to sleep disruption was estimated with a well validated sleep model and a Monte Carlo computer simulation in an effort to optimize the quantity of consumables. METHODS: The key components of the model are the mission parameter program, the calculation of sleep intensity and the diagnosis and decision module. The mission parameter program was used to create simulated daily sleep/wake schedules for an ISS increment. The hypothetical schedules included critical events such as dockings and extravehicular activities and included actual sleep time and sleep quality. The schedules were used as inputs to the Sleep, Activity, Fatigue and Task Effectiveness (SAFTE) Model (IBR Inc., Baltimore MD), which calculated sleep intensity. Sleep data from an ISS study was used to relate calculated sleep intensity to the probability of sleep medication use, using a generalized linear model for binomial regression. A human yes/no decision process using a binomial random number was also factored into sleep medication use probability. RESULTS: These probability calculations were repeated 5000 times resulting in an estimate of the most likely amount of sleep aids used during an ISS mission and a 95% confidence interval. CONCLUSIONS: These results were transferred to the parent IMM for further weighting and integration with other medical conditions, to help inform operational decisions. This model is a potential planning tool for ensuring adequate sleep during sleep disrupted periods of a mission.

[Cost comparison of open and robot-assisted partial nephrectomy in treatment of renal tumor].

PubMed

Abd El Fattah, V; Chevrot, A; Meusy, A; Mercier, G; Wagner, L; Soustelle, L; Boukaram, M; Thuret, R; Costa, P; Droupy, S

2016-04-01

Robot-assisted partial nephrectomy rapidly took on among urologists, even though studies showing its superiority over other techniques are still scarce and its costs hard to evaluate, especially in the French medical system. To evaluate the cost overrun of robot-assisted partial nephrectomy compared to that of open partial nephrectomy. From January 2010 to December 2013, 77 patients underwent a partial nephrectomy, 46 of which by robot-assisted laparoscopy and the remaining 31 by lombotomy. The two groups were similar in composition. Economic data regarding the staff, the consumables and the premises involved have been analyzed. Costs are significantly higher in the NPR group (9253.21 euros vs. 7448.42 euros) due to higher consumable expenses as well as the costs pertaining to the amortization and maintenance of the robot. Yet, that difference tends to diminish as the duration of the experiment increases. No significant difference was found in warm ischemia times, operation duration and renal function a month after the operation. On the other hand, patients from the NPR group spent a significantly smaller amount of time in recovery room (159 minutes vs. 205 minutes, P=0.004), presented fewer complications and were discharged faster (6.1 days vs. 8.1 days, P=0.04). To be profitable for the hospital in the French GHS system, robot-assisted partial nephrectomy must take place in a complex where at least 300 robot-assisted interventions are performed annually, in the framework of a hospitalization lasting four days or less, the use of a single needle holder and no systematic use of a haemostatic agent. 4. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Space Costing: Who Should Pay for the Use of College Space? A Report.

ERIC Educational Resources Information Center

Zacher, Sy

The costs of owning and operating physical facilities are consuming an increasing share of the budgets of colleges and universities. In the past, academic and operating units of colleges have viewed their space as a free commodity and often used it extravagantly. Space costing is a method of cost accounting the space and operating and maintenance…