Front-of-pack nutrition labels. Their effect on attention and choices when consumers have varying goals and time constraints.

PubMed

van Herpen, Erica; Trijp, Hans C M van

2011-08-01

Although front-of-pack nutrition labeling can help consumers make healthier food choices, lack of attention to these labels limits their effectiveness. This study examines consumer attention to and use of three different nutrition labeling schemes (logo, multiple traffic-light label, and nutrition table) when they face different goals and resource constraints. To understand attention and processing of labels, various measures are used including self-reported use, recognition, and eye-tracking measures. Results of two experiments in different countries show that although consumers evaluate the nutrition table most positively, it receives little attention and does not stimulate healthy choices. Traffic-light labels and especially logos enhance healthy product choice, even when consumers are put under time pressure. Additionally, health goals of consumers increase attention to and use of nutrition labels, especially when these health goals concern specific nutrients. Copyright © 2011 Elsevier Ltd. All rights reserved.

Preparation, characterization and dissolution of passive oxide film on the 400 series stainless steel surfaces

NASA Astrophysics Data System (ADS)

Sathyaseelan, V. S.; Rufus, A. L.; Chandramohan, P.; Subramanian, H.; Velmurugan, S.

2015-12-01

Full system decontamination of Primary Heat Transport (PHT) system of Pressurised Heavy Water Reactors (PHWRs) resulted in low decontamination factors (DF) on stainless steel (SS) surfaces. Hence, studies were carried out with 403 SS and 410 SS that are the material of construction of "End-Fitting body" and "End-Fitting Liner tubes". Three formulations were evaluated for the dissolution of passive films formed over these alloys viz., i) Two-step process consisting of oxidation and reduction reactions, ii) Dilute Chemical Decontamination (DCD) and iii) High Temperature Process. The two-step and high temperature processes could dissolve the oxide completely while the DCD process could remove only 60%. Various techniques like XRD, Raman spectroscopy and SEM-EDX were used for assessing the dissolution process. The two-step process is time consuming, laborious while the high temperature process is less time consuming and is recommended for SS decontamination.

Evaluating Process Improvement Courses of Action Through Modeling and Simulation

DTIC Science & Technology

2017-09-16

changes to a process is time consuming and has potential to overlook stochastic effects. By modeling a process as a Numerical Design Structure Matrix...13 Methods to Evaluate Process Performance ................................................................15 The Design Structure...Matrix ......................................................................................16 Numerical Design Structure Matrix

A Web-Based Course Assessment Tool with Direct Mapping to Student Outcomes

ERIC Educational Resources Information Center

Ibrahim, Walid; Atif, Yacine; Shuaib, Khaled; Sampson, Demetrios

2015-01-01

The assessment of curriculum outcomes is an essential element for continuous academic improvement. However, the collection, aggregation and analysis of assessment data are notoriously complex and time-consuming processes. At the same time, only few developments of supporting electronic processes and tools for continuous academic program assessment…

[The temporal dimension of drugs: a sociological analysis based on a category key to the study of health-disease-care processes].

PubMed

Sánchez Antelo, Victoria

2016-03-01

The temporal dimensions that shape the senses and practices of men and women who are poly-consumers of psychoactive substances, 18-35 years of age, and living in the metropolitan area of Buenos Aires were analyzed. Using a qualitative approach, 29 individual in-depth interviews were carried out and then analyzed through a constant comparative analysis process between the categories generated from the data obtained and the theoretical concepts. From the analysis, practices and meanings emerge that regulate the diverse temporalities that underlie drug consumption: feelings related to body rhythms, periods between consumptions, the timing of phases of the life cycle, or unspecific temporalities that become an adequate "moment" for consumption. These practices require that particular attention be paid to time, as this enables the flexibility to consume without being a consumer, to use drugs without being addicted to them.

Association mapping of SSR markers to sweet, bitter and roasted peanut sensory attributes in cultivated peanut

USDA-ARS?s Scientific Manuscript database

Certain roasted peanut quality sensory attributes are important breeding objectives for peanut product manufacturers and consumers. Currently the only means of measuring these traits is the use of a trained sensory panel. This is a costly and time-consuming process. It is desirable, from a cost, ti...

Some Communication and Demographic Determinants of Adolescent Consumer Learning.

ERIC Educational Resources Information Center

Moore, Roy L.; Stephens, Lowndes F.

Four basic objectives were investigated in this study. Age differences were tested on various dependent skills measured to determine if consumer skills change over a period of time; the extent of integration of the dependent measures within the two age groups was ascertained; antecedent processes within groups that account for variation in…

[Research on the Application of Lean Management in Medical Consumables Material Logistics Management].

PubMed

Yang, Chai; Zhang, Wei; Gu, Wei; Shen, Aizong

2016-11-01

Solve the problems of high cost, low utilization rate of resources, low medical care quality problem in medical consumables material logistics management for scientific of medical consumables management. Analysis of the problems existing in the domestic medical consumables material logistics management in hospital, based on lean management method, SPD(Supply, Processing, Distribution) for specific applications, combined HBOS(Hospital Business Operation System), HIS (Hospital Information System) system for medical consumables material management. Achieve the lean management in medical consumables material purchase, warehouse construction, push, clinical use and retrospect. Lean management in medical consumables material can effectively control the cost in logistics management, optimize the alocation of resources, liberate unnecessary time of medical staff, improve the quality of medical care. It is a scientific management method.

The Australian funding debate on quadrivalent HPV vaccine: a case study for the national pharmaceutical policy.

PubMed

Roughead, Elizabeth Ellen; Gilbert, Andrew L; Vitry, Agnes I

2008-12-01

To analyse the media and political reactions to the initial decision of the Pharmaceutical Benefits Advisory Committee (PBAC) to reject funding of the quadrivalent human papilloma virus (HPV) vaccine in Australia. A case study, informed by media reports and government documents, was utilised to examine the reactions of key stakeholders; PBAC, consumers, consumer organisations, pharmaceutical industry, politicians, health professionals and the media to the initial decision to reject funding of HPV vaccine. The initial decision to reject funding of the HPV vaccine led to unprecedented public response with over 300 newspaper articles and calls by consumers, health professionals and politicians to intervene in the decision making process. Misunderstanding of the decision making process, particularly cost-effectiveness assessments, the need for an independent process, the legislated inability of a timely and transparent response from policy makers and the lack of a risk mitigation strategy all played a role in the public outcry. Despite 15 years of implementation of cost-effectiveness assessments there is still a need for improving stakeholder understanding of the decision making process and for timely transfer of complete information. Risk mitigation strategies should be considered as part of the communication plan for all decisions.

A study of an adaptive replication framework for orchestrated composite web services.

PubMed

Mohamed, Marwa F; Elyamany, Hany F; Nassar, Hamed M

2013-01-01

Replication is considered one of the most important techniques to improve the Quality of Services (QoS) of published Web Services. It has achieved impressive success in managing resource sharing and usage in order to moderate the energy consumed in IT environments. For a robust and successful replication process, attention should be paid to suitable time as well as the constraints and capabilities in which the process runs. The replication process is time-consuming since outsourcing some new replicas into other hosts is lengthy. Furthermore, nowadays, most of the business processes that might be implemented over the Web are composed of multiple Web services working together in two main styles: Orchestration and Choreography. Accomplishing a replication over such business processes is another challenge due to the complexity and flexibility involved. In this paper, we present an adaptive replication framework for regular and orchestrated composite Web services. The suggested framework includes a number of components for detecting unexpected and unhappy events that might occur when consuming the original published web services including failure or overloading. It also includes a specific replication controller to manage the replication process and select the best host that would encapsulate a new replica. In addition, it includes a component for predicting the incoming load in order to decrease the time needed for outsourcing new replicas, enhancing the performance greatly. A simulation environment has been created to measure the performance of the suggested framework. The results indicate that adaptive replication with prediction scenario is the best option for enhancing the performance of the replication process in an online business environment.

Understanding Housing Delays and Relocations Within the Housing First Model.

PubMed

Zerger, Suzanne; Pridham, Katherine Francombe; Jeyaratnam, Jeyagobi; Hwang, Stephen W; O'Campo, Patricia; Kohli, Jaipreet; Stergiopoulos, Vicky

2016-01-01

This study explores factors contributing to delays and relocations during the implementation of the Housing First model in Toronto, Ontario. While interruptions in housing tenure are expected en route to recovery and housing stability, consumer and service provider views on finding and keeping housing remain largely unknown. In-person interviews and focus groups were conducted with 48 study participants, including 23 case managers or housing workers and 25 consumers. The following three factors contributed to housing delays and transfers: (1) the effectiveness of communication and collaboration among consumers and service providers, (2) consumer-driven preferences and ambivalence, and (3) provider prioritization of consumer choice over immediate housing access. Two strategies--targeted communications and consumer engagement in housing searches--supported the housing process. Several factors affect the timing and stability of housing. Communication between and among providers and consumers, and a shared understanding of consumer choice, can further support choice and recovery.

Evaluation and audit in a paediatric disability service.

PubMed Central

Cass, H D; Kugler, B T

1993-01-01

Parental and professional responses to questionnaires evaluating a paediatric disability service are reported and the viability of auditing structural, process, and outcome aspects of clinical practice are discussed. Expectations of waiting time to first appointment (met for only 52% of consumers) illustrate structural issues. Process issues are reflected in consumer reactions to outreach work (for example, 94% of parents and 84% of professionals found this supportive). Outcome measures such as consumer satisfaction with the service (76% of consumers reported being 'very satisfied' and 20% 'fairly satisfied') suggest that service aims are being met. Good concurrence of service aims with consumer needs is indicated by parental reasons for referral (for example, 75% for diagnostic help, 73% for a better understanding of the disorder, 88% for practical help), referrers' reasons (for example, 55% for a second diagnostic opinion, 45% due to lack of local expertise), and reports from most other professionals involved with the case that a similar service was not provided locally. PMID:8466242

Evaluation and audit in a paediatric disability service.

PubMed

Cass, H D; Kugler, B T

1993-03-01

Parental and professional responses to questionnaires evaluating a paediatric disability service are reported and the viability of auditing structural, process, and outcome aspects of clinical practice are discussed. Expectations of waiting time to first appointment (met for only 52% of consumers) illustrate structural issues. Process issues are reflected in consumer reactions to outreach work (for example, 94% of parents and 84% of professionals found this supportive). Outcome measures such as consumer satisfaction with the service (76% of consumers reported being 'very satisfied' and 20% 'fairly satisfied') suggest that service aims are being met. Good concurrence of service aims with consumer needs is indicated by parental reasons for referral (for example, 75% for diagnostic help, 73% for a better understanding of the disorder, 88% for practical help), referrers' reasons (for example, 55% for a second diagnostic opinion, 45% due to lack of local expertise), and reports from most other professionals involved with the case that a similar service was not provided locally.

Consumption of vegetables and their relation with ultra-processed foods in Brazil

PubMed Central

Canella, Daniela Silva; Louzada, Maria Laura da Costa; Claro, Rafael Moreira; Costa, Janaina Calu; Bandoni, Daniel Henrique; Levy, Renata Bertazzi; Martins, Ana Paula Bortoletto

2018-01-01

ABSTRACT OBJECTIVE To characterize the household purchase and the individual consumption of vegetables in Brazil and to analyze their relation with the consumption of ultra-processed foods. METHODS We have used data on the purchase of food for household consumption and individual consumption from the 2008–2009 Brazilian Household Budget Survey. The Brazilian Household Budget Survey studied the purchase of food of 55,970 households and the food consumption of 34,003 individuals aged 10 years and over. The foods of interest in this study were vegetables (excluding roots and tubers) and ultra-processed foods. We have described the amount of vegetables (grams) purchased and consumed by all Brazilians and according to the quintiles of caloric intake of ultra-processed food. To this end, we have calculated the crude and predicted values obtained by regression models adjusted for sociodemographic variables. We have analyzed the most commonly purchased types of vegetables (% in the total amount) and, in relation to individual food consumption, the variety of vegetables consumed (absolute number), the participation (%) of the types of culinary preparations based on vegetables, and the time of consumption. RESULTS The adjusted mean household purchase of vegetables was 42.9 g/per capita/day. The adjusted mean individual consumption was 46.1 g. There was an inverse relation between household purchase and individual consumption of vegetables and ultra-processed foods. Ten types of vegetables account for more than 80% of the total amount usually purchased. The variety consumed was, on average, 1.08 type/per capita/day. Approximately 60% of the vegetables were eaten raw, and the amount consumed at lunch was twice that consumed at dinner; individuals with higher consumption of ultra-processed foods tended to consume even less vegetables at dinner. CONCLUSIONS The consumption of vegetables in Brazil is insufficient, and this is worse among individuals with higher consumption of ultra-processed foods. The most frequent habit was to consume raw vegetables at lunch and with limited variety. PMID:29791530

Formulation of detailed consumables management models for the development (preoperational) period of advanced space transportation system. Volume 2: Consumables data base workbook

NASA Technical Reports Server (NTRS)

Zamora, M. A.

1976-01-01

The consumables characteristic data associated with the performance of the mission activities required by the mission planning processor are defined to calculate the consumables requirements. The activity data is defined in terms of discrete time periods having a distinct rate for each consumable required to support the performance of a given operation. The data is structured in a series of consumable data worksheets for each activity that includes a profile of its operations and the rate of each consumable required to support the given activity. The data worksheets provide for the uniform specification of consumables data, allows for the ready identification of the consumables affected by a given activity, and facilitates the updating process. An activity and the data that must be included in the data worksheets are defined and an example of its use and application the consumables data requirements for the performance of the EVA are presented.

Natural games

NASA Astrophysics Data System (ADS)

Anttila, Jani; Annila, Arto

2011-10-01

A course of a game is formulated as a physical process that will consume free energy in the least time. Accordingly, the rate of entropy increase is the payoff function that will subsume all forms of free energy that motivate diverse decisions. Also other concepts of game theory are related to their profound physical counterparts. When the physical portrayal of behavior is mathematically analyzed, the course of a game is found to be inherently unpredictable because each move affects motives in the future. Despite the non-holonomic character of the natural process, the objective of consuming free energy in the least time will direct an extensive-form game toward a Lyapunov-stable point that satisfies the minimax theorem.

The Effect of Time on Mediation Deficiency in Children and Adults

ERIC Educational Resources Information Center

Peterson, Candida C.

1973-01-01

Results support the inference that symbolic mediation is a measurably time-consuming process and that temporal factors are involved in the ontogenetic transition from single-link to symbolically mediated behavior. (Author/CB)

Numerical analysis of heat treatment of TiCN coated AA7075 aluminium alloy

NASA Astrophysics Data System (ADS)

Srinath, M. K.; Prasad, M. S. Ganesha

2018-04-01

The Numerical analysis of heat treatments of TiCN coated AA7075 aluminium alloys is presented in this paper. The Convection-Diffusion-Reaction (CDR) equation with solutions in the Streamlined-Upward Petrov-Galerkin (SUPG) method for different parameters is provided for the understanding of the process. An experimental process to improve the surface properties of AA-7075 aluminium alloy was attempted through the coatings of TiCN and subsequent heat treatments. From the experimental process, optimized temperature and time was obtained which gave the maximum surface hardness and corrosion resistance. The paper gives an understanding and use of the CDR equation for application of the process. Expression to determine convection, diffusion and reaction parameters are provided which is used to obtain the overall expression of the heat treatment process. With the substitution of the optimized temperature and time, the governing equation may be obtained. Additionally, the total energy consumed during the heat treatment process is also developed to give a mathematical formulation of the energy consumed.

A Stochastic Spiking Neural Network for Virtual Screening.

PubMed

Morro, A; Canals, V; Oliver, A; Alomar, M L; Galan-Prado, F; Ballester, P J; Rossello, J L

2018-04-01

Virtual screening (VS) has become a key computational tool in early drug design and screening performance is of high relevance due to the large volume of data that must be processed to identify molecules with the sought activity-related pattern. At the same time, the hardware implementations of spiking neural networks (SNNs) arise as an emerging computing technique that can be applied to parallelize processes that normally present a high cost in terms of computing time and power. Consequently, SNN represents an attractive alternative to perform time-consuming processing tasks, such as VS. In this brief, we present a smart stochastic spiking neural architecture that implements the ultrafast shape recognition (USR) algorithm achieving two order of magnitude of speed improvement with respect to USR software implementations. The neural system is implemented in hardware using field-programmable gate arrays allowing a highly parallelized USR implementation. The results show that, due to the high parallelization of the system, millions of compounds can be checked in reasonable times. From these results, we can state that the proposed architecture arises as a feasible methodology to efficiently enhance time-consuming data-mining processes such as 3-D molecular similarity search.

Cause and effect: the linkage between the health information seeking behavior and the online environment--a review.

PubMed

Bratucu, R; Gheorghe, I R; Purcarea, R M; Gheorghe, C M; Popa Velea, O; Purcarea, V L

2014-09-15

Today, health care consumers are taking more control over their health care problems, investing more time in finding and getting information as well as looking for proper methods in order to investigate more closely the health care information received from their physicians. Unfortunately, in health care consumers' views, the trustworthiness of health authorities and institutions has declined in the last years. So, consumers have found a new solution to their health problems, that is, the Internet. Recently, studies revealed that consumers seeking for health information have more options to look for data in comparison to the methods used a few years ago. Therefore, due to the available technology, consumers have more outlets to search for information. For instance, the Internet is a source that has revolutionized the way consumers seek data due its customized methods of assessing both quantitative and qualitative information which may be achieved with minimal effort and low costs, offering at the same time, several advantages such as making the decision process more efficient.

Information Processing in Memory Tasks.

ERIC Educational Resources Information Center

Johnston, William A.

The intensity of information processing engendered in different phases of standard memory tasks was examined in six experiments. Processing intensity was conceptualized as system capacity consumed, and was measured via a divided-attention procedure in which subjects performed a memory task and a simple reaction-time (RT) task concurrently. The…

78 FR 4418 - Electronic Submission Process for Requesting Export Certificates From the Center for Devices and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-22

... (CDRH). The electronic process will help fulfill both the legislative and application time processing... Devices and Radiological Health (CDRH), Division of Small Manufacturers, International and Consumer... regulated by CDRH as a voluntary alternative to paper submissions. With electronic submissions, CDRH can...

Automated Interactive Simulation Model (AISIM) VAX Version 5.0 Training Manual.

DTIC Science & Technology

1987-05-29

action, activity, decision , etc. that consumes time. The entity is automatically created by the system when an ACTION Primitive is placed. 1.3.2.4 The...MODELED SYSTEM 1.3.2.1 The Process Entity. A Process is used to represent the operations, decisions , actions or activities that can be decomposed and...is associated with the Action entity described below, is included in Process definitions to indicate the time a certain Action (or process, decision

A Quantitative Analysis of Virginia Public School Special Education Due Process Cases and Their Resolutions from 2004-2016

ERIC Educational Resources Information Center

Beaudoin-Saunders, Valerie Ann

2017-01-01

Special education-related lawsuits are a concern to school systems. They are time-consuming, expensive, and contentious. School and parental relationships become strained when litigation is involved. This study analyzed data from the Virginia Department of Education's due process database over a 12-year period of time to note common disabilities…

Automatic recognition of lactating sow behaviors through depth image processing

USDA-ARS?s Scientific Manuscript database

Manual observation and classification of animal behaviors is laborious, time-consuming, and of limited ability to process large amount of data. A computer vision-based system was developed that automatically recognizes sow behaviors (lying, sitting, standing, kneeling, feeding, drinking, and shiftin...

Analysis of consumer behavior in decision making of purchasing ornamental freshwater fish (case of study at ornamental freshwater fish market at Peta Street, Bandung)

NASA Astrophysics Data System (ADS)

Gumilar, I.; Rizal, A.; Sriati; Setiawan Putra, R.

2018-04-01

This research aim was to analyzed process of decision making of purchasing ornamental freshwater fish at Peta Street, Bandung City and Analyzed what factors are driving consumers to buy freshwater fish Peta Street. The method used in this research is case study with rating scale and rank spearman analysis. The sampling technique is the accidental random sampling method consist of 30 respondents. The consumer’s decision making process consist of five stages, namely the recognition of needs, information searching, alternative evaluation, process of purchasing, and the evaluation of results. The results showed that at the stage of recognition of needs the motivation of purchasing freshwater fish because respondents are very fond of ornamental freshwater fish, at the stage of information search, the information sources are from the print media and friends or neighborhood. At the stage of alternative evaluation, the reason consumers buy ornamental freshwater fish because the quality of good products. The stage of purchasing decision process consumers bought 1-5 fish with frequency of purchase 1 time per month. The evaluation of results of post-purchasing consumers feel very satisfied with the fish products and the price is very affordable. To observe the factors that influence purchasing motivation of consumers, spearman rank test is the method. The results showed that the quality and price of the product are the factors that most influence the purchase decision of ornamental freshwater fish with the range of student-t value 3,968 and 2,107.

DGIC Interconnection Insights | Distributed Generation Interconnection

Science.gov Websites

time and resources from utilities, customers, and local permitting authorities. Past research by the interconnection processes can benefit all parties by reducing the financial and time commitments involved. In this susceptible to time-consuming setbacks-for example, if an application is submitted with incomplete information

Variation in the Oral Processing of Everyday Meals Is Associated with Fullness and Meal Size; A Potential Nudge to Reduce Energy Intake?

PubMed

Ferriday, Danielle; Bosworth, Matthew L; Godinot, Nicolas; Martin, Nathalie; Forde, Ciarán G; Van Den Heuvel, Emmy; Appleton, Sarah L; Mercer Moss, Felix J; Rogers, Peter J; Brunstrom, Jeffrey M

2016-05-21

Laboratory studies have demonstrated that experimental manipulations of oral processing can have a marked effect on energy intake. Here, we explored whether variations in oral processing across a range of unmodified everyday meals could affect post-meal fullness and meal size. In Study 1, female participants (N = 12) attended the laboratory over 20 lunchtime sessions to consume a 400-kcal portion of a different commercially available pre-packaged meal. Prior to consumption, expected satiation was assessed. During each meal, oral processing was characterised using: (i) video-recordings of the mouth and (ii) real-time measures of plate weight. Hunger and fullness ratings were elicited pre- and post-consumption, and for a further three hours. Foods that were eaten slowly had higher expected satiation and delivered more satiation and satiety. Building on these findings, in Study 2 we selected two meals (identical energy density) from Study 1 that were equally liked but maximised differences in oral processing. On separate days, male and female participants (N = 24) consumed a 400-kcal portion of either the "fast" or "slow" meal followed by an ad libitum meal (either the same food or a dessert). When continuing with the same food, participants consumed less of the slow meal. Further, differences in food intake during the ad libitum meal were not compensated at a subsequent snacking opportunity an hour later. Together, these findings suggest that variations in oral processing across a range of unmodified everyday meals can affect fullness after consuming a fixed portion and can also impact meal size. Modifying food form to encourage increased oral processing (albeit to a lesser extent than in experimental manipulations) might represent a viable target for food manufacturers to help to nudge consumers to manage their weight.

Consumer responses to advertising on the Internet: the effect of individual difference on ambivalence and avoidance.

PubMed

Jin, Chang Hyun; Villegas, Jorge

2007-04-01

The purpose of this study was to understand the effect that individual characteristics have on consumer advertising processing under high- and low-interactivity circumstances on the Web. Tests on the relationship between individual differences and advertising responses form the basis of this empirical study on the Web. The results indicated that consumers have a higher tendency to avoid or experience ambivalence about Internet advertisements under low-interactivity circumstances, and attitudinal ambivalence lead to avoidance when responding to advertisements on the Internet. Personality variables are the main factors in consumer decision-making behaviors and Internet characteristics, such as levels of interactivity, can greatly influence the effectiveness of advertising in online environments. Advertising credibility could influence people's consumer attitudes, beliefs, or behaviors over time on the Web.

Left behind in the return-to-work journey: consumer insights for policy change and practice strategies.

PubMed

Korzycki, Monica; Korzycki, Martha; Shaw, Lynn

2008-01-01

This study examined system barriers that precluded injured workers from accessing services and supports in the return-to-work (RTW) process. A grounded theory approach was used to investigate injured worker experiences. Methods included in-depth telephone interviews and the constant comparative method to analyze the data. Findings revealed that consumers experienced tensions or a tug-of-war between the RTW system, the health care system, and in accessing and using knowledge. Over time consumers reflected upon these tensions and initiated strategies to enhance return to function and RTW. Insights from consumer-driven strategies that might inform future policy change and promote positive service delivery for injured workers are examined.

Wastewater Biosolid Composting Optimization Based on UV-VNIR Spectroscopy Monitoring

PubMed Central

Temporal-Lara, Beatriz; Melendez-Pastor, Ignacio; Gómez, Ignacio; Navarro-Pedreño, Jose

2016-01-01

Conventional wastewater treatment generates large amounts of organic matter–rich sludge that requires adequate treatment to avoid public health and environmental problems. The mixture of wastewater sludge and some bulking agents produces a biosolid to be composted at adequate composting facilities. The composting process is chemically and microbiologically complex and requires an adequate aeration of the biosolid (e.g., with a turner machine) for proper maturation of the compost. Adequate (near) real-time monitoring of the compost maturity process is highly difficult and the operation of composting facilities is not as automatized as other industrial processes. Spectroscopic analysis of compost samples has been successfully employed for compost maturity assessment but the preparation of the solid compost samples is difficult and time-consuming. This manuscript presents a methodology based on a combination of a less time-consuming compost sample preparation and ultraviolet, visible and short-wave near-infrared spectroscopy. Spectroscopic measurements were performed with liquid compost extract instead of solid compost samples. Partial least square (PLS) models were developed to quantify chemical fractions commonly employed for compost maturity assessment. Effective regression models were obtained for total organic matter (residual predictive deviation—RPD = 2.68), humification ratio (RPD = 2.23), total exchangeable carbon (RPD = 2.07) and total organic carbon (RPD = 1.66) with a modular and cost-effective visible and near infrared (VNIR) spectroradiometer. This combination of a less time-consuming compost sample preparation with a versatile sensor system provides an easy-to-implement, efficient and cost-effective protocol for compost maturity assessment and near-real-time monitoring. PMID:27854280

Wastewater Biosolid Composting Optimization Based on UV-VNIR Spectroscopy Monitoring.

PubMed

Temporal-Lara, Beatriz; Melendez-Pastor, Ignacio; Gómez, Ignacio; Navarro-Pedreño, Jose

2016-11-15

Conventional wastewater treatment generates large amounts of organic matter-rich sludge that requires adequate treatment to avoid public health and environmental problems. The mixture of wastewater sludge and some bulking agents produces a biosolid to be composted at adequate composting facilities. The composting process is chemically and microbiologically complex and requires an adequate aeration of the biosolid (e.g., with a turner machine) for proper maturation of the compost. Adequate (near) real-time monitoring of the compost maturity process is highly difficult and the operation of composting facilities is not as automatized as other industrial processes. Spectroscopic analysis of compost samples has been successfully employed for compost maturity assessment but the preparation of the solid compost samples is difficult and time-consuming. This manuscript presents a methodology based on a combination of a less time-consuming compost sample preparation and ultraviolet, visible and short-wave near-infrared spectroscopy. Spectroscopic measurements were performed with liquid compost extract instead of solid compost samples. Partial least square (PLS) models were developed to quantify chemical fractions commonly employed for compost maturity assessment. Effective regression models were obtained for total organic matter (residual predictive deviation-RPD = 2.68), humification ratio (RPD = 2.23), total exchangeable carbon (RPD = 2.07) and total organic carbon (RPD = 1.66) with a modular and cost-effective visible and near infrared (VNIR) spectroradiometer. This combination of a less time-consuming compost sample preparation with a versatile sensor system provides an easy-to-implement, efficient and cost-effective protocol for compost maturity assessment and near-real-time monitoring.

Differential responsiveness to caffeine and perceived effects of caffeine in moderate and high regular caffeine consumers.

PubMed

Attwood, A S; Higgs, S; Terry, P

2007-03-01

Individual differences in responsiveness to caffeine occur even within a caffeine-consuming population, but the factors that mediate differential responsiveness remain unclear. To compare caffeine's effects on performance and mood in a group of high vs moderate consumers of caffeine and to examine the potential role of subjective awareness of the effects of caffeine in mediating any differential responsiveness. Two groups of regular caffeine consumers (<200 mg/day and >200 mg/day) attended two sessions at which mood and cognitive functions were measured before and 30 min after consumption of 400-mg caffeine or placebo in a capsule. Cognitive tests included visual information processing, match-to-sample visual search (MTS) and simple and choice reaction times. Post-session questionnaires asked participants to describe any perceived effect of capsule consumption. High consumers, but not moderate consumers, demonstrated significantly faster simple and choice reaction times after caffeine relative to placebo. These effects were not attributable to obvious group differences in withdrawal or tolerance because there were no group differences in baseline mood or in reports of negative affect after caffeine. Instead, the high consumers were more likely to report experiencing positive effects of caffeine, whereas the moderate consumers were more likely to report no effect. The sensitivity of caffeine consumers to the mood- and performance-enhancing effects of caffeine is related to their levels of habitual intake. High caffeine consumers are more likely than moderate consumers to perceive broadly positive effects of caffeine, and this may contribute to their levels of use.

Time versus money.

PubMed

Monga, Ashwani; Zor, Ozum

2018-04-21

Consumers are known to spend both time and money. These two resources are often seen as economically comparable because the value of one's time can be equated to a monetary amount, such as one's wage rate. Recent research suggests that even when time and money are economically equivalent, they are psychologically different. We discuss how time (versus money) leads to decision making that is more heuristic rather than systematic, to an orientation that is more emotional rather than value-maximizing, to a thinking process that is more holistic rather than analytic, and to a mindset that is more abstract rather than concrete. Implications arise for a variety of domains such as consumer search, happiness, product evaluation, and charitable giving. Copyright © 2018 Elsevier Ltd. All rights reserved.

[Preferential habits of consumers of common bean (Phaseolus vulgaris L.) in Mexico].

PubMed

Castellanos, J Z; Guzmán Maldonado, H; Jiménez, A; Mejía, C; Muñoz Ramos, J J; Acosta Gallegos, J A; Hoyos, G; López Salinas, E; González Eguiarte, D; Salinas Pérez, R; González Acuña, J; Muñoz Villalobos, J A; Fernández Hernández, P; Cáceres, B

1997-06-01

A detailed knowledge of the consumer's preferences for the different classes of common bean is useful to define objectives in bean breeding and quality projects in a given region or country and it is also a valuable tool to design marketing strategies. The present work consisted on the application of a survey to 1514 common bean consumers in 14 states of Mexico. To facilitate the interpretation of the results the country was divided in four regions: North East, North West, Center and South. In the North West region, 98% of the surveyed individuals eat the "Azufrado" types (sulphur yellow); in the North East, 70% of the consumers prefer "pinto" (beige with brown mottles) and "Bayo" (cream) types; in the South, 90% of the consumers prefer the "Black" type; and in the Center of the country, all commercial classes are consumed. Within a commercial class, specific characteristics are demanded. For instance, in the black type, small and opaque seeds are preferred while in the "Flor de mayo" (Beige with pink mottles) type medium to large seeds having bright seed coat are preferred. The main characteristics utilized by consumers to select a given bean type are cooking time and flavor. It was observed that preferential classes are well established among the consumers since 70% responded that they would not change the preferred class even if the alternative class was sold to a lower price. Consumers do not soak the beans, because it changes the flavor and the aspect of the cooked beans and they do not add salt at the beginning of the cooking process due to the same reason. Organoleptic studies conducted in the laboratory confirmed that soaking of beans or addition of salts in the soaking water or at the beginning of the cooking process negatively affected acceptability of cooked beans by panelists. In this paper aspects related to ways of processing and consuming common beans as well as marketing aspects are discussed.

Importance of interactions between food quality, quantity, and gut transit time on consumer feeding, growth, and trophic dynamics.

PubMed

Mitra, Aditee; Flynn, Kevin J

2007-05-01

Ingestion kinetics of animals are controlled by both external food availability and feedback from the quantity of material already within the gut. The latter varies with gut transit time (GTT) and digestion of the food. Ingestion, assimilation efficiency, and thus, growth dynamics are not related in a simple fashion. For the first time, the important linkage between these processes and GTT is demonstrated; this is achieved using a biomass-based, mechanistic multinutrient model fitted to experimental data for zooplankton growth dynamics when presented with food items of varying quality (stoichiometric composition) or quantity. The results show that trophic transfer dynamics will vary greatly between the extremes of feeding on low-quantity/high-quality versus high-quantity/low-quality food; these conditions are likely to occur in nature. Descriptions of consumer behavior that assume a constant relationship between the kinetics of grazing and growth irrespective of food quality and/or quantity, with little or no recognition of the combined importance of these factors on consumer behavior, may seriously misrepresent consumer activity in dynamic situations.

Design and evaluation of a service oriented architecture for paperless ICU tarification.

PubMed

Steurbaut, Kristof; Colpaert, Kirsten; Van Hoecke, Sofie; Steurbaut, Sabrina; Danneels, Chris; Decruyenaere, Johan; De Turck, Filip

2012-06-01

The computerization of Intensive Care Units provides an overwhelming amount of electronic data for both medical and financial analysis. However, the current tarification, which is the process to tick and count patients' procedures, is still a repetitive, time-consuming process on paper. Nurses and secretaries keep track manually of the patients' medical procedures. This paper describes the design methodology and implementation of automated tarification services. In this study we investigate if the tarification can be modeled in service oriented architecture as a composition of interacting services. Services are responsible for data collection, automatic assignment of records to physicians and application of rules. Performance is evaluated in terms of execution time, cost evaluation and return on investment based on tracking of real procedures. The services provide high flexibility in terms of maintenance, integration and rules support. It is shown that services offer a more accurate, less time-consuming and cost-effective tarification.

The Decoy Duck.

ERIC Educational Resources Information Center

Ryan, Anna

1997-01-01

Describes the development processes of an instructional video for use in a course offered through the Extended Learning Institute of Northern Virginia Community College entitled Women Writers II. Characterizes the process of transforming this English course from a print-based to a distance-learning course as time-consuming, creative, and…

[Consumer's psychological processes of hoarding and avoidant purchasing after the Tohoku earthquake].

PubMed

Ohtomo, Shoji; Hirose, Yukio

2014-02-01

This study examined psychological processes of consumers that had determined hoarding and avoidant purchasing behaviors after the Tohoku earthquake within a dual-process model. The model hypothesized that both intentional motivation based on reflective decision and reactive motivation based on non-reflective decision predicted the behaviors. This study assumed that attitude, subjective norm and descriptive norm in relation to hoarding and avoidant purchasing were determinants of motivations. Residents in the Tokyo metropolitan area (n = 667) completed internet longitudinal surveys at three times (April, June, and November, 2011). The results indicated that intentional and reactive motivation determined avoidant purchasing behaviors in June; only intentional motivation determined the behaviors in November. Attitude was a main determinant of the motivations each time. Moreover, previous behaviors predicted future behaviors. In conclusion, purchasing behaviors were intentional rather than reactive behaviors. Furthermore, attitude and previous behaviors were important determinants in the dual-process model. Attitude and behaviors formed in April continued to strengthen the subsequent decisions of purchasing behavior.

Surrogate modelling for the prediction of spatial fields based on simultaneous dimensionality reduction of high-dimensional input/output spaces.

PubMed

Crevillén-García, D

2018-04-01

Time-consuming numerical simulators for solving groundwater flow and dissolution models of physico-chemical processes in deep aquifers normally require some of the model inputs to be defined in high-dimensional spaces in order to return realistic results. Sometimes, the outputs of interest are spatial fields leading to high-dimensional output spaces. Although Gaussian process emulation has been satisfactorily used for computing faithful and inexpensive approximations of complex simulators, these have been mostly applied to problems defined in low-dimensional input spaces. In this paper, we propose a method for simultaneously reducing the dimensionality of very high-dimensional input and output spaces in Gaussian process emulators for stochastic partial differential equation models while retaining the qualitative features of the original models. This allows us to build a surrogate model for the prediction of spatial fields in such time-consuming simulators. We apply the methodology to a model of convection and dissolution processes occurring during carbon capture and storage.

Cognitive and mood improvements of caffeine in habitual consumers and habitual non-consumers of caffeine.

PubMed

Haskell, Crystal F; Kennedy, David O; Wesnes, Keith A; Scholey, Andrew B

2005-06-01

The cognitive and mood effects of caffeine are well documented. However, the majority of studies in this area involve caffeine-deprived, habitual caffeine users. It is therefore unclear whether any beneficial findings are due to the positive effects of caffeine or to the alleviation of caffeine withdrawal. The present placebo-controlled, double-blind, balanced crossover study investigated the acute cognitive and mood effects of caffeine in habitual users and habitual non-users of caffeine. Following overnight caffeine withdrawal, 24 habitual caffeine consumers (mean=217 mg/day) and 24 habitual non-consumers (20 mg/day) received a 150 ml drink containing either 75 or 150 mg of caffeine or a matching placebo, at intervals of > or =48 h. Cognitive and mood assessments were undertaken at baseline and 30 min post-drink. These included the Cognitive Drug Research computerised test battery, two serial subtraction tasks, a sentence verification task and subjective visual analogue mood scales. There were no baseline differences between the groups' mood or performance. Following caffeine, there were significant improvements in simple reaction time, digit vigilance reaction time, numeric working memory reaction time and sentence verification accuracy, irrespective of group. Self-rated mental fatigue was reduced and ratings of alertness were significantly improved by caffeine independent of group. There were also group effects for rapid visual information processing false alarms and spatial memory accuracy with habitual consumers outperforming non-consumers. There was a single significant interaction of group and treatment effects on jittery ratings. Separate analyses of each groups' responses to caffeine revealed overlapping but differential responses to caffeine. Caffeine tended to benefit consumers' mood more while improving performance more in the non-consumers. These results do not support a withdrawal alleviation model. Differences in the patterns of responses to caffeine by habitual consumers and habitual non-consumers may go some way to explaining why some individuals become caffeine consumers.

Cause and effect: the linkage between the health information seeking behavior and the online environment- a review

PubMed Central

Bratucu, R; Gheorghe, IR; Purcarea, RM; Gheorghe, CM; Popa Velea, O; Purcarea, VL

2014-01-01

Abstract Today, health care consumers are taking more control over their health care problems, investing more time in finding and getting information as well as looking for proper methods in order to investigate more closely the health care information received from their physicians. Unfortunately, in health care consumers’ views, the trustworthiness of health authorities and institutions has declined in the last years. So, consumers have found a new solution to their health problems, that is, the Internet. Recently, studies revealed that consumers seeking for health information have more options to look for data in comparison to the methods used a few years ago. Therefore, due to the available technology, consumers have more outlets to search for information. For instance, the Internet is a source that has revolutionized the way consumers seek data due its customized methods of assessing both quantitative and qualitative information which may be achieved with minimal effort and low costs, offering at the same time, several advantages such as making the decision process more efficient. PMID:25408746

Consumer satisfaction with telehealth advice-nursing.

PubMed

Chang, B L; Mayo, A; Omery, A

2001-01-01

An increase in interest in the establishment of telephone advice services has resulted in the proliferation of call centers. Despite their wide usage, research for the most part has not addressed the quality of care in relation to consumer satisfaction. This paper examines consumer outcomes of satisfaction, and follow-up with recommendations, within a framework of the nursing process and its associated components of assessment (including problem identification), care planning, intervention, and evaluation. The data for the study were obtained from seven after-hours call centers operating under the auspices of health maintenance organizations, preferred provider organizations, and private insurance companies. A sample of 157 non-redundant telephone calls from adults with medical-surgical problems were audiotaped with providers' and callers' consent. Sociodemographic information of the advice nurses, and chief complaints of the callers were obtained. The quality of nursing of the audiotaped calls was rated through an implicit review method by registered nurse raters using an advice nurse structured implicit review (AN-SIR) form developed for the study. Follow-up information was obtained through telephone calls to ascertain the consumers' perceptions of satisfaction, helpfulness, and follow-through with recommendations. Results indicated that consumers calling with a variety of general complaints contacted 32 nurses in advice nurse call centers. The quality of nursing process was found to be the best in the area of intervention. Evaluation was also well above the midpoint on a transformed scale of zero to 100. Assessment, although slightly above midpoint, was the lowest of the three components of the nursing process examined. Consumer satisfaction was high with 95.4 percent of the consumers rating the calls as completely or at least somewhat satisfied, and 93.2 percent, stating the advice was very or somewhat helpful. Exploratory regression analysis showed that the component of intervention was significantly related to consumer satisfaction. The present study pioneers the way to rate the quality of the advice nurses' interactions with consumers, and lays the groundwork for further investigations of health care provider behavior and consumer outcomes. Further studies are recommended to investigate predictors of consumer satisfaction, and cost-benefit in terms of consumer expenditures of time, funds, and energy.

Real time microcontroller implementation of an adaptive myoelectric filter.

PubMed

Bagwell, P J; Chappell, P H

1995-03-01

This paper describes a real time digital adaptive filter for processing myoelectric signals. The filter time constant is automatically selected by the adaptation algorithm, giving a significant improvement over linear filters for estimating the muscle force and controlling a prosthetic device. Interference from mains sources often produces problems for myoelectric processing, and so 50 Hz and all harmonic frequencies are reduced by an averaging filter and differential process. This makes practical electrode placement and contact less critical and time consuming. An economic real time implementation is essential for a prosthetic controller, and this is achieved using an Intel 80C196KC microcontroller.

The roles of users in shaping transitions to new energy systems

NASA Astrophysics Data System (ADS)

Schot, Johan; Kanger, Laur; Verbong, Geert

2016-05-01

Current government information policies and market-based instruments aimed at influencing the energy choices of consumers often ignore the fact that consumer behaviour is not fully reducible to individuals making rational conscious decisions all the time. The decisions of consumers are largely configured by shared routines embedded in socio-technical systems. To achieve a transition towards a decarbonized and energy-efficient system, an approach that goes beyond individual consumer choice and puts shared routines and system change at its centre is needed. Here, adopting a transitions perspective, we argue that consumers should be reconceptualized as users who are important stakeholders in the innovation process shaping new routines and enacting system change. We review the role of users in shifts to new decarbonized and energy-efficient systems and provide a typology of user roles.

12 CFR Appendix A to Part 343 - Consumer Grievance Process

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 4 2011-01-01 2011-01-01 false Consumer Grievance Process A Appendix A to Part... POLICY CONSUMER PROTECTION IN SALES OF INSURANCE Pt. 343, App. A Appendix A to Part 343—Consumer Grievance Process Any consumer who believes that any bank or any other person selling, soliciting...

Scheduling job shop - A case study

NASA Astrophysics Data System (ADS)

Abas, M.; Abbas, A.; Khan, W. A.

2016-08-01

The scheduling in job shop is important for efficient utilization of machines in the manufacturing industry. There are number of algorithms available for scheduling of jobs which depend on machines tools, indirect consumables and jobs which are to be processed. In this paper a case study is presented for scheduling of jobs when parts are treated on available machines. Through time and motion study setup time and operation time are measured as total processing time for variety of products having different manufacturing processes. Based on due dates different level of priority are assigned to the jobs and the jobs are scheduled on the basis of priority. In view of the measured processing time, the times for processing of some new jobs are estimated and for efficient utilization of the machines available an algorithm is proposed and validated.

Consumer trait variation influences tritrophic interactions in salt marsh communities.

PubMed

Hughes, Anne Randall; Hanley, Torrance C; Orozco, Nohelia P; Zerebecki, Robyn A

2015-07-01

The importance of intraspecific variation has emerged as a key question in community ecology, helping to bridge the gap between ecology and evolution. Although much of this work has focused on plant species, recent syntheses have highlighted the prevalence and potential importance of morphological, behavioral, and life history variation within animals for ecological and evolutionary processes. Many small-bodied consumers live on the plant that they consume, often resulting in host plant-associated trait variation within and across consumer species. Given the central position of consumer species within tritrophic food webs, such consumer trait variation may play a particularly important role in mediating trophic dynamics, including trophic cascades. In this study, we used a series of field surveys and laboratory experiments to document intraspecific trait variation in a key consumer species, the marsh periwinkle Littoraria irrorata, based on its host plant species (Spartina alterniflora or Juncus roemerianus) in a mixed species assemblage. We then conducted a 12-week mesocosm experiment to examine the effects of Littoraria trait variation on plant community structure and dynamics in a tritrophic salt marsh food web. Littoraria from different host plant species varied across a suite of morphological and behavioral traits. These consumer trait differences interacted with plant community composition and predator presence to affect overall plant stem height, as well as differentially alter the density and biomass of the two key plant species in this system. Whether due to genetic differences or phenotypic plasticity, trait differences between consumer types had significant ecological consequences for the tritrophic marsh food web over seasonal time scales. By altering the cascading effects of the top predator on plant community structure and dynamics, consumer differences may generate a feedback over longer time scales, which in turn influences the degree of trait divergence in subsequent consumer populations.

Consumer input into health care: Time for a new active and comprehensive model of consumer involvement.

PubMed

Hall, Alix E; Bryant, Jamie; Sanson-Fisher, Rob W; Fradgley, Elizabeth A; Proietto, Anthony M; Roos, Ian

2018-03-07

To ensure the provision of patient-centred health care, it is essential that consumers are actively involved in the process of determining and implementing health-care quality improvements. However, common strategies used to involve consumers in quality improvements, such as consumer membership on committees and collection of patient feedback via surveys, are ineffective and have a number of limitations, including: limited representativeness; tokenism; a lack of reliable and valid patient feedback data; infrequent assessment of patient feedback; delays in acquiring feedback; and how collected feedback is used to drive health-care improvements. We propose a new active model of consumer engagement that aims to overcome these limitations. This model involves the following: (i) the development of a new measure of consumer perceptions; (ii) low cost and frequent electronic data collection of patient views of quality improvements; (iii) efficient feedback to the health-care decision makers; and (iv) active involvement of consumers that fosters power to influence health system changes. © 2018 The Authors Health Expectations published by John Wiley & Sons Ltd.

Continuous processing and the applications of online tools in pharmaceutical product manufacture: developments and examples.

PubMed

Ooi, Shing Ming; Sarkar, Srimanta; van Varenbergh, Griet; Schoeters, Kris; Heng, Paul Wan Sia

2013-04-01

Continuous processing and production in pharmaceutical manufacturing has received increased attention in recent years mainly due to the industries' pressing needs for more efficient, cost-effective processes and production, as well as regulatory facilitation. To achieve optimum product quality, the traditional trial-and-error method for the optimization of different process and formulation parameters is expensive and time consuming. Real-time evaluation and the control of product quality using an online process analyzer in continuous processing can provide high-quality production with very high-throughput at low unit cost. This review focuses on continuous processing and the application of different real-time monitoring tools used in the pharmaceutical industry for continuous processing from powder to tablets.

Making a splash!

PubMed

Weston, David

2012-05-01

The installation of a birthing pool can be a costly and time consuming process. This article provides some practical tips for making the installation run as smoothly as possible, saving work--and money--in the process. This article gives some advice as to what needs to be considered before you go ahead with installing a pool.

Organic acid formulation and dip to control listeria monocytogenes in hot dogs.

USDA-ARS?s Scientific Manuscript database

Processed meat products such as frankfurters, smoked sausage, and deli meat have gained popularity because consumers have less time for food preparation and demand more convenient meat items. Because these products are handled post processing and may not be reheated before consumption, the presence...

Development of Quantitative Structure-Activity Relationship (QSAR) Models to Predict the Carcinogenic Potency of Chemicals

EPA Science Inventory

Determining the carcinogenicity and carcinogenic potency of new chemicals is both a labor-intensive and time-consuming process. In order to expedite the screening process, there is a need to either: (1) identify alternative toxicity measures (shorter duration) that may be used as...

Student Costing: An Essential Tool in Site-based Budgeting and Teacher Empowerment.

ERIC Educational Resources Information Center

Sanders, K. Penney; Thiemann, Francis C.

1990-01-01

Although the process of participative, school-based budgeting might seem tedious and time-consuming, it can truly empower teachers and administrators. One cannot set instructional and budgetary priorities without knowing costs. A costing formula to help facilitate the budgeting process is presented. Includes 18 references. (MLH)

Community Meetings for Emergency Research Community Consultation

DTIC Science & Technology

2008-01-01

authors com- mented they found the entire community consultation process burdensome, time- consuming , and expensive (6). Given the time investment...Holloway KFC : Accidental communities: Race, emergency medicine, and the problem of PolyHeme. Am J Bioeth 2006; 6:7–17 12. Dickert NW, Sugarman J: Community

RAPID DETECTION METHOD FOR E.COLI, ENTEROCOCCI AND BACTEROIDES IN RECREATIONAL WATER

EPA Science Inventory

Current methodology for determining fecal contamination of drinking water sources and recreational waters rely on the time-consuming process of bacterial multiplication and require at least 24 hours from the time of sampling to the possible determination that the water is unsafe ...

The Brot System

NASA Astrophysics Data System (ADS)

Lanzing, Jan

1988-01-01

Processing meteor data from observation notes to a format which is used by people who use the observations for statistical reduction is a very time consuming business. It cost our group in Hengelo (Buurse) so much time that there were complaints by the reducers. That day we realized that we had to automatize the process of formatting. Because of the small budget we had to work with what we had, a CBM-64 homecomputer.

12 CFR Appendix A to Part 14 - Consumer Grievance Process

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Consumer Grievance Process A Appendix A to Part 14 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN SALES OF INSURANCE Pt. 14, App. A Appendix A to Part 14—Consumer Grievance Process Any consumer who...

12 CFR Appendix A to Part 536 - Consumer Grievance Process

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Consumer Grievance Process A Appendix A to Part 536 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN SALES OF INSURANCE Pt. 536, App. A Appendix A to Part 536—Consumer Grievance Process Any consumer who...

12 CFR Appendix A to Part 14 - Consumer Grievance Process

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 1 2011-01-01 2011-01-01 false Consumer Grievance Process A Appendix A to Part 14 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN SALES OF INSURANCE Pt. 14, App. A Appendix A to Part 14—Consumer Grievance Process Any consumer who...

A Data Preparation Methodology in Data Mining Applied to Mortality Population Databases.

PubMed

Pérez, Joaquín; Iturbide, Emmanuel; Olivares, Víctor; Hidalgo, Miguel; Martínez, Alicia; Almanza, Nelva

2015-11-01

It is known that the data preparation phase is the most time consuming in the data mining process, using up to 50% or up to 70% of the total project time. Currently, data mining methodologies are of general purpose and one of their limitations is that they do not provide a guide about what particular task to develop in a specific domain. This paper shows a new data preparation methodology oriented to the epidemiological domain in which we have identified two sets of tasks: General Data Preparation and Specific Data Preparation. For both sets, the Cross-Industry Standard Process for Data Mining (CRISP-DM) is adopted as a guideline. The main contribution of our methodology is fourteen specialized tasks concerning such domain. To validate the proposed methodology, we developed a data mining system and the entire process was applied to real mortality databases. The results were encouraging because it was observed that the use of the methodology reduced some of the time consuming tasks and the data mining system showed findings of unknown and potentially useful patterns for the public health services in Mexico.

Application of lean six sigma to waste minimization in cigarette paper industry

NASA Astrophysics Data System (ADS)

Syahputri, K.; Sari, R. M.; Anizar; Tarigan, I. R.; Siregar, I.

2018-02-01

The cigarette paper industry is one of the industry that is always experiencing increasing demand from consumers. Consumer expectations for the products produced also increased both in terms of quality and quantity. The company continuously improves the quality of its products by trying to minimize nonconformity, waste and improve the efficiency of the whole production process of the company. In this cigarette industry, there is a disability whose value is above the company’s defect tolerance that is 10% of the production amount per month. Another problem also occurs in the production time is too long due to the many activities that are not value added (non value added activities) on the production floor. To overcome this problem, it is necessary to improve the production process of cigarette paper and minimize production time by reducing non value added activities. Repairs done with Lean Six Sigma. Lean Six Sigma is a combination of Lean and Six Sigma concept with DMAIC method (Define, Measure, Analyze, Improve, Control). With this Lean approach, obtained total production time of 1479.13 minutes proposal with cycle efficiency process increased by 12.64%.

Effective nursing care of adolescents with anorexia nervosa: a consumer perspective.

PubMed

Zugai, Joel; Stein-Parbury, Jane; Roche, Michael

2013-07-01

To establish how nurses ensure weight gain and a positive inpatient experience for the treatment of adolescents with anorexia nervosa by considering consumer perspectives. Consumer perspective literature indicates approval and dissatisfaction with certain aspects of the inpatient experience, and there is a limited understanding of what consumers perceive to be effective nursing practice. The design of this study was qualitative, the data being interpreted with a thematic analysis. This study sought the perspectives of eight (n = 8) recovered consumers through semi-structured interviews. Nurses were considered highly influential over the inpatient experience. The findings of this study are characterised by three overall themes regarding nursing practice: (1) ensuring weight gain, (2) maintaining a therapeutic milieu, and (3) the nursing relationship. Consumers have clear perspectives of how nurses effectively ensure weight gain and how nurses ensure a positive inpatient experience. The quality of relationships between consumers and nurses had implications for both weight gain and the perceived quality of the inpatient experience. By relying on the strength of positive, thoughtful and well-timed interactions, nurses may contribute to productive physical outcomes and a positive inpatient experience. Consumers indicated that motivation to adhere to care was derived from strong relationships with nurses. Ensuring both weight gain and a positive experience involves achieving a productive 'balance of restrictions'. Consumers also valued nurses that created a comfortable and productive environment. This study indicates that the process of weight gain may be enhanced when accompanied by a process of therapeutic engagement. Therapeutic alliance may be an effective way for nurses to ensure weight gain and an enhanced inpatient experience. Therapeutically beneficial relationships may enhance treatment and possibly enhance outcomes for consumers. © 2013 Blackwell Publishing Ltd.

The impact of consumer involvement in research: an evaluation of consumer involvement in the London Primary Care Studies Programme.

PubMed

Wyatt, Katrina; Carter, Mary; Mahtani, Vinita; Barnard, Angela; Hawton, Annie; Britten, Nicky

2008-06-01

The value of consumer involvement in health services research is widely recognized. While there is a growing body of evidence about the principles of good consumer involvement, there is little research about the effect that involvement can have on the research. This evaluation assessed the level and impact of consumer involvement in the London Primary Care Studies Programme (LPCSP), all of whose individual projects had to demonstrate substantial involvement as a condition of funding. To evaluate consumer involvement in the LPSCP and understand what impact consumers had on the research process and outcomes. A multi-method case study approach was undertaken, using survey techniques, interviews, focus groups, observation and scrutiny of written documents. The overall data set comprised 61 questionnaires, 44 semi-structured interviews, 2 focus groups and 15 hours of observation of meetings. Eleven primary care-based research projects which together made up the LPCSP. An in-depth description of consumer involvement in the Programme was produced. Nine projects had consumers as co-applicants, four projects had been completed before the evaluation began and one was still ongoing at the time of the evaluation. Of the eight projects which have produced final reports, all met their aims and objectives. Consumers had had an additional impact in the research, in the initial design of the study, in recruitment of the research subjects, in developing data collection tools, in collecting the data, in analysis and disseminating the findings. Consumer involvement in National Health Service research is a relatively recent policy development and while there is an increasing amount of literature about how and why consumers should be involved in research, there is less evidence about the impact of such involvement. This evaluation provides evidence about the impact that consumers have not only on the research process but also on the outcomes of the research.

A Telemetry Browser Built with Java Components

NASA Astrophysics Data System (ADS)

Poupart, E.

In the context of CNES balloon scientific campaigns and telemetry survey field, a generic telemetry processing product, called TelemetryBrowser in the following, was developed reusing COTS, Java Components for most of them. Connection between those components relies on a software architecture based on parameter producers and parameter consumers. The first one transmit parameter values to the second one which has registered to it. All of those producers and consumers can be spread over the network thanks to Corba, and over every kind of workstation thanks to Java. This gives a very powerful mean to adapt to constraints like network bandwidth, or workstations processing or memory. It's also very useful to display and correlate at the same time information coming from multiple and various sources. An important point of this architecture is that the coupling between parameter producers and parameter consumers is reduced to the minimum and that transmission of information on the network is made asynchronously. So, if a parameter consumer goes down or runs slowly, there is no consequence on the other consumers, because producers don't wait for their consumers to finish their data processing before sending it to other consumers. An other interesting point is that parameter producers, also called TelemetryServers in the following are generated nearly automatically starting from a telemetry description using Flavori component. Keywords Java components, Corba, distributed application, OpenORBii, software reuse, COTS, Internet, Flavor. i Flavor (Formal Language for Audio-Visual Object Representation) is an object-oriented media representation language being developed at Columbia University. It is designed as an extension of Java and C++ and simplifies the development of applications that involve a significant media processing component (encoding, decoding, editing, manipulation, etc.) by providing bitstream representation semantics. (flavor.sourceforge.net) ii OpenORB provides a Java implementation of the OMG Corba 2.4.2 specification (openorb.sourceforge.net) 1/16

Reduction of produced elementary sulfur in denitrifying sulfide removal process.

PubMed

Zhou, Xu; Liu, Lihong; Chen, Chuan; Ren, Nanqi; Wang, Aijie; Lee, Duu-Jong

2011-05-01

Denitrifying sulfide removal (DSR) processes simultaneously convert sulfide, nitrate, and chemical oxygen demand from industrial wastewater into elemental sulfur, dinitrogen gas, and carbon dioxide, respectively. The failure of a DSR process is signaled by high concentrations of sulfide in reactor effluent. Conventionally, DSR reactor failure is blamed for overcompetition for heterotroph to autotroph communities. This study indicates that the elementary sulfur produced by oxidizing sulfide that is a recoverable resource from sulfide-laden wastewaters can be reduced back to sulfide by sulfur-reducing Methanobacterium sp. The Methanobacterium sp. was stimulated with excess organic carbon (acetate) when nitrite was completely consumed by heterotrophic denitrifiers. Adjusting hydraulic retention time of a DSR reactor when nitrite is completely consumed provides an additional control variable for maximizing DSR performance.

The Time Factor: Leveraging Intelligent Agents and Directed Narratives in Online Learning Environments

ERIC Educational Resources Information Center

Jones, Greg; Warren, Scott

2009-01-01

Using video games, virtual simulations, and other digital spaces for learning can be a time-consuming process; aside from technical issues that may absorb class time, students take longer to achieve gains in learning in virtual environments. Greg Jones and Scott Warren describe how intelligent agents, in-game characters that respond to the context…

Academic consumer researchers: a bridge between consumers and researchers.

PubMed

Griffiths, Kathleen M; Jorm, Anthony F; Christensen, Helen

2004-04-01

To describe the contributions that consumers, and academic consumer researchers in particular, can make to mental health research. A literature survey and a systematic consideration of the potential advantages of consumer and academic consumer researcher involvement in health research. Consumer researchers may contribute to better health outcomes, but there are significant barriers to their participation in the research process. To date, discussion has focused on the role of nonacademic consumers in the health research process. There has been little recognition of the particular contributions that consumers with formal academic qualifications and research experience can offer. Academic consumer researchers (ACRs) offer many of the advantages associated with lay consumer participation, as well as some unique advantages. These advantages include acceptance by other researchers as equal partners in the research process; skills in research; access to research funding; training in disseminating research findings within the scientific community; potential to influence research funding and research policy; capacity to influence the research culture; and potential to facilitate the involvement of lay consumers in the research process. In recognition of the value of a critical mass of ACRs in mental health, a new ACR unit (the Depression and Anxiety Consumer Research Unit [CRU]) has been established at the Centre for Mental Health Research at the Australian National University. Academic consumer researchers have the potential to increase the relevance of mental health research to consumers, to bridge the gap between the academic and consumer communities and to contribute to the process of destigmatizing mental disorders.

Flow cytometry as a method for the evaluation of raw material, product and process in the dairy industry.

PubMed

Ruszczyńska, A; Szteyn, J; Wiszniewska-Laszczych, A

2007-01-01

Producing dairy products which are safe for consumers requires the constant monitoring of the microbiological quality of raw material, the production process itself and the end product. Traditional methods, still a "gold standard", require a specialized laboratory working on recognized and validated methods. Obtaining results is time- and labor-consuming and do not allow rapid evaluation. Hence, there is a need for a rapid, precise method enabling the real-time monitoring of microbiological quality, and flow cytometry serves this function well. It is based on labeling cells suspended in a solution with fluorescent dyes and pumping them into a measurement zone where they are exposed to a precisely focused laser beam. This paper is aimed at presenting the possibilities of applying flow cytometry in the dairy industry.

CRITTERS! A Realistic Simulation for Teaching Evolutionary Biology

ERIC Educational Resources Information Center

Latham, Luke G., II; Scully, Erik P.

2008-01-01

Evolutionary processes can be studied in nature and in the laboratory, but time and financial constraints result in few opportunities for undergraduate and high school students to explore the agents of genetic change in populations. One alternative to time consuming and expensive teaching laboratories is the use of computer simulations. We…

Infantry Small-Unit Mountain Operations

DTIC Science & Technology

2011-02-01

expended to traverse it.  Unique sustainment solutions. Sustainment in a mountain environment is a challenging and time-consuming process . Terrain...a particular environment during the intelligence preparation of the battlefield (IPB) process and provide the analysis to the company. The IPB...consists of a four-step process that includes—  Defining the operational environment.  Describing environmental effects on operations.  Evaluating the

Helium process cycle

DOEpatents

Ganni, Venkatarao

2008-08-12

A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

Helium process cycle

DOEpatents

Ganni, Venkatarao

2007-10-09

A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

Does Consumer Confidence Forecast Household Saving and Borrowing Behavior? Evidence for Poland.

PubMed

Kłopocka, Aneta Maria

2017-01-01

Consumer confidence plays an important role in households' decision-making processes. This study investigates the effects of consumer confidence on household saving and borrowing behavior that are unsatisfactorily considered in previous discussions. The questions of interest are first, whether indexes of consumer confidence have any predictive power on their own for future household saving and borrowing rates, and second, whether they contain information about future household saving and borrowing rates aside from the information contained in other available indicators. In addition to aggregate confidence indicators, their components are used to provide more precise information. Overall, the multiple linear regression analysis (OLS technique) of Polish time-series data gives positive answers to both questions. This finding supports the recommendation of combining the strengths of objective indicators (such as economic fundamentals) and subjective indicators (such as consumer confidence) to improve household financial behavior forecasts.

The effects of concurrent cannabis use among ecstasy users: neuroprotective or neurotoxic?

PubMed

Fisk, John E; Montgomery, Catharine; Wareing, Michelle; Murphy, Philip N

2006-08-01

The research evidence regarding the potential effects of ecstasy suggests that it may be neurotoxic and that its use is associated with cognitive impairment. In recent years evidence has emerged suggesting that cannabinoids, the active ingredients in cannabis, can be neuroprotective under certain conditions. Given that many ecstasy users also consume cannabis at the same time, the possibility emerges that these individuals might be less susceptible to ecstasy-related impairment. The present paper reanalyses the data from a number of previous studies, contrasting the performance of those individuals who generally consume cannabis and ecstasy at the same time with those who generally consume ecstasy on its own. The two ecstasy-using groups are compared with non-ecstasy users on a range of measures including processing speed, random letter generation, verbal and visuo-spatial working memory span, reasoning and associative learning. The two ecstasy user groups did not differ significantly from each other on any of the measures. Both user groups were significantly worse than non-ecstasy users on measures of associative learning, verbal and visuo-spatial working memory and reasoning. The results suggest that consuming cannabis at the same time as ecstasy does not reduce the likelihood of cognitive impairment.

ADESSA: A Real-Time Decision Support Service for Delivery of Semantically Coded Adverse Drug Event Data

PubMed Central

Duke, Jon D.; Friedlin, Jeff

2010-01-01

Evaluating medications for potential adverse events is a time-consuming process, typically involving manual lookup of information by physicians. This process can be expedited by CDS systems that support dynamic retrieval and filtering of adverse drug events (ADE’s), but such systems require a source of semantically-coded ADE data. We created a two-component system that addresses this need. First we created a natural language processing application which extracts adverse events from Structured Product Labels and generates a standardized ADE knowledge base. We then built a decision support service that consumes a Continuity of Care Document and returns a list of patient-specific ADE’s. Our database currently contains 534,125 ADE’s from 5602 product labels. An NLP evaluation of 9529 ADE’s showed recall of 93% and precision of 95%. On a trial set of 30 CCD’s, the system provided adverse event data for 88% of drugs and returned these results in an average of 620ms. PMID:21346964

Nondestructive Evaluation Technology Working Group Report (IDA/OSD R&M (Institute for Defense Analyses/Office of the Secretary of Defense Reliability and Maintainability Study).

DTIC Science & Technology

1983-08-01

evaluating surface residual stresses in ferromagnetic materials, but until recently has - been considered too time consuming for production application. Fast...generic residual stress , X-ray, image processing, neutron processing, neutron radiography, vibrothermography, nuclear magnetic resonance 20. ABSTRACT...studied, this technology study effort would not have been possible within the time and resources available. P-3 i La

I Will Do It If I Enjoy It! The Moderating Effect of Seeking Sensory Pleasure When Exposed to Participatory CSR Campaigns.

PubMed

Ruiz de Maya, Salvador; Lardín-Zambudio, Rafaela; López-López, Inés

2015-01-01

In an attempt to gain differentiation, companies are allocating resources to corporate social responsibility (CSR) initiatives. At the same time, they are giving consumers a more active role in the process of creating value. In this sense, consumer participation represents a new approach to gain competitive advantage. However, the effectiveness of consumer participation in CSR campaigns still remains unknown. With the purpose of shedding light on this issue, this paper shows that participatory CSR campaigns lead to greater consumer perceptions of CSR, which in turn results in more favorable attitudes toward the company. Furthermore, the effect is stronger for sensory pleasure seekers, whose involvement with the experience is greater. The findings contribute to the CSR literature and reveal important implications for marketers.

Variation in the Oral Processing of Everyday Meals Is Associated with Fullness and Meal Size; A Potential Nudge to Reduce Energy Intake?

PubMed Central

Ferriday, Danielle; Bosworth, Matthew L.; Godinot, Nicolas; Martin, Nathalie; Forde, Ciarán G.; Van Den Heuvel, Emmy; Appleton, Sarah L.; Mercer Moss, Felix J.; Rogers, Peter J.; Brunstrom, Jeffrey M.

2016-01-01

Laboratory studies have demonstrated that experimental manipulations of oral processing can have a marked effect on energy intake. Here, we explored whether variations in oral processing across a range of unmodified everyday meals could affect post-meal fullness and meal size. In Study 1, female participants (N = 12) attended the laboratory over 20 lunchtime sessions to consume a 400-kcal portion of a different commercially available pre-packaged meal. Prior to consumption, expected satiation was assessed. During each meal, oral processing was characterised using: (i) video-recordings of the mouth and (ii) real-time measures of plate weight. Hunger and fullness ratings were elicited pre- and post-consumption, and for a further three hours. Foods that were eaten slowly had higher expected satiation and delivered more satiation and satiety. Building on these findings, in Study 2 we selected two meals (identical energy density) from Study 1 that were equally liked but maximised differences in oral processing. On separate days, male and female participants (N = 24) consumed a 400-kcal portion of either the “fast” or “slow” meal followed by an ad libitum meal (either the same food or a dessert). When continuing with the same food, participants consumed less of the slow meal. Further, differences in food intake during the ad libitum meal were not compensated at a subsequent snacking opportunity an hour later. Together, these findings suggest that variations in oral processing across a range of unmodified everyday meals can affect fullness after consuming a fixed portion and can also impact meal size. Modifying food form to encourage increased oral processing (albeit to a lesser extent than in experimental manipulations) might represent a viable target for food manufacturers to help to nudge consumers to manage their weight. PMID:27213451

Regulation of cold-induced sweetening in potatoes and markers for fast-track new variety development

USDA-ARS?s Scientific Manuscript database

Potato breeding is a tedious, time consuming process. With the growing requirements of the potato processing industry for new potato varieties, there is need for effective tools to speed-up new variety development. The purpose of this study was to understand the enzymatic regulation of cold-induce...

Toward Modeling the Learner's Personality Using Educational Games

ERIC Educational Resources Information Center

Essalmi, Fathi; Tlili, Ahmed; Ben Ayed, Leila Jemni; Jemmi, Mohamed

2017-01-01

Learner modeling is a crucial step in the learning personalization process. It allows taking into consideration the learner's profile to make the learning process more efficient. Most studies refer to an explicit method, namely questionnaire, to model learners. Questionnaires are time consuming and may not be motivating for learners. Thus, this…

Allocation of Limited Cognitive Resources during Text Comprehension in a Second Language

ERIC Educational Resources Information Center

Morishima, Yasunori

2013-01-01

For native (L1) comprehenders, lower-level language processes such as lexical access and parsing are considered to consume few cognitive resources. In contrast, these processes pose considerable demands for second-language (L2) comprehenders. Two reading-time experiments employing inconsistency detection found that English learners did not detect…

Consumer-driven nutrient dynamics in freshwater ecosystems: from individuals to ecosystems.

PubMed

Atkinson, Carla L; Capps, Krista A; Rugenski, Amanda T; Vanni, Michael J

2017-11-01

The role of animals in modulating nutrient cycling [hereafter, consumer-driven nutrient dynamics (CND)] has been accepted as an important influence on both community structure and ecosystem function in aquatic systems. Yet there is great variability in the influence of CND across species and ecosystems, and the causes of this variation are not well understood. Here, we review and synthesize the mechanisms behind CND in fresh waters. We reviewed 131 articles on CND published between 1973 and 1 June 2015. The rate of new publications in CND has increased from 1.4 papers per year during 1973-2002 to 7.3 per year during 2003-2015. The majority of investigations are in North America with many concentrating on fish. More recent studies have focused on animal-mediated nutrient excretion rates relative to nutrient demand and indirect impacts (e.g. decomposition). We identified several mechanisms that influence CND across levels of biological organization. Factors affecting the stoichiometric plasticity of consumers, including body size, feeding history and ontogeny, play an important role in determining the impact of individual consumers on nutrient dynamics and underlie the stoichiometry of CND across time and space. The abiotic characteristics of an ecosystem affect the net impact of consumers on ecosystem processes by influencing consumer metabolic processes (e.g. consumption and excretion/egestion rates), non-CND supply of nutrients and ecosystem nutrient demand. Furthermore, the transformation and transport of elements by populations and communities of consumers also influences the flow of energy and nutrients across ecosystem boundaries. This review highlights that shifts in community composition or biomass of consumers and eco-evolutionary underpinnings can have strong effects on the functional role of consumers in ecosystem processes, yet these are relatively unexplored aspects of CND. Future research should evaluate the value of using species traits and abiotic conditions to predict and understand the effects of consumers on ecosystem-level nutrient dynamics across temporal and spatial scales. Moreover, new work in CND should strive to integrate knowledge from disparate fields of ecology and environmental science, such as physiology and ecosystem ecology, to develop a comprehensive and mechanistic understanding of the functional role of consumers. Comparative and experimental studies that develop testable hypotheses to challenge the current assumptions of CND, including consumer stoichiometric homeostasis, are needed to assess the significance of CND among species and across freshwater ecosystems. © 2016 Cambridge Philosophical Society.

A time-driven, activity-based costing methodology for determining the costs of red blood cell transfusion in patients with beta thalassaemia major.

PubMed

Burns, K E; Haysom, H E; Higgins, A M; Waters, N; Tahiri, R; Rushford, K; Dunstan, T; Saxby, K; Kaplan, Z; Chunilal, S; McQuilten, Z K; Wood, E M

2018-04-10

To describe the methodology to estimate the total cost of administration of a single unit of red blood cells (RBC) in adults with beta thalassaemia major in an Australian specialist haemoglobinopathy centre. Beta thalassaemia major is a genetic disorder of haemoglobin associated with multiple end-organ complications and typically requiring lifelong RBC transfusion therapy. New therapeutic agents are becoming available based on advances in understanding of the disorder and its consequences. Assessment of the true total cost of transfusion, incorporating both product and activity costs, is required in order to evaluate the benefits and costs of these new therapies. We describe the bottom-up, time-driven, activity-based costing methodology used to develop process maps to provide a step-by-step outline of the entire transfusion pathway. Detailed flowcharts for each process are described. Direct observations and timing of the process maps document all activities, resources, staff, equipment and consumables in detail. The analysis will include costs associated with performing these processes, including resources and consumables. Sensitivity analyses will be performed to determine the impact of different staffing levels, timings and probabilities associated with performing different tasks. Thirty-one process maps have been developed, with over 600 individual activities requiring multiple timings. These will be used for future detailed cost analyses. Detailed process maps using bottom-up, time-driven, activity-based costing for determining the cost of RBC transfusion in thalassaemia major have been developed. These could be adapted for wider use to understand and compare the costs and complexities of transfusion in other settings. © 2018 British Blood Transfusion Society.

Factors that predict consumer acceptance of enriched processed meats.

PubMed

Shan, Liran C; Henchion, Maeve; De Brún, Aoife; Murrin, Celine; Wall, Patrick G; Monahan, Frank J

2017-11-01

The study aimed to understand predictors of consumers' purchase intention towards processed meat based functional foods (i.e. enriched processed meat). A cross-sectional survey was conducted with 486 processed meat consumers in spring 2016. Results showed that processed meats were perceived differently in healthiness, with sausage-type products perceived less healthy than cured meat products. Consumers were in general more uncertain than positive about enriched processed meat but differences existed in terms of the attitudes and purchase intention. Following regression analysis, consumers' purchase intention towards enriched processed meat was primarily driven by their attitudes towards the product concept. Perceived healthiness of existing products and eating frequency of processed meat were also positively associated with the purchase intention. Other factors such as general food choice motives, socio-demographic characteristics, consumer health and the consumption of functional foods and dietary supplements in general, were not significant predictors of the purchase intention for enriched processed meat. Copyright © 2017 Elsevier Ltd. All rights reserved.

An Ontological Informatics Framework for Pharmaceutical Product Development: Milling as a Case Study

ERIC Educational Resources Information Center

Akkisetty, Venkata Sai Pavan Kumar

2009-01-01

Pharmaceutical product development is an expensive, time consuming and information intensive process. Providing the right information at the right time is of great importance in pharmaceutical industry. To achieve this, knowledge management is the approach to deal with the humongous quantity of information. Ontological approach proposed in Venkat…

Strategies to reduce sodium consumption: a food industry perspective.

PubMed

Dötsch, Mariska; Busch, Johanneke; Batenburg, Max; Liem, Gie; Tareilus, Erwin; Mueller, Rudi; Meijer, Gert

2009-11-01

The global high prevalence of hypertension and cardiovascular disease has raised concerns regarding the sodium content of the foods which we consume. Over 75% of sodium intake in industrialized diets is likely to come from processed and restaurant foods. Therefore international authorities, such as the World Health Organisation, are encouraging the food industry to reduce sodium levels in their products. Significant sodium reduction is not without complications as salt plays an important role in taste, and in some products is needed also for preservation and processing. The most promising sodium reduction strategy is to adapt the preference of consumers for saltiness by reducing sodium in products in small steps. However, this is a time-consuming approach that needs to be applied industry-wide in order to be effective. Therefore the food industry is also investigating solutions that will maintain the same perceived salt intensity at lower sodium levels. Each of these has specific advantages, disadvantages, and time lines for implementation. Currently applied approaches are resulting in sodium reduction between 20-30%. Further reduction will require new technologies. Research into the physiology of taste perception and salt receptors is an emerging area of science that is needed in order to achieve larger sodium reductions.

Episodic memory and appetite regulation in humans.

PubMed

Brunstrom, Jeffrey M; Burn, Jeremy F; Sell, Nicola R; Collingwood, Jane M; Rogers, Peter J; Wilkinson, Laura L; Hinton, Elanor C; Maynard, Olivia M; Ferriday, Danielle

2012-01-01

Psychological and neurobiological evidence implicates hippocampal-dependent memory processes in the control of hunger and food intake. In humans, these have been revealed in the hyperphagia that is associated with amnesia. However, it remains unclear whether 'memory for recent eating' plays a significant role in neurologically intact humans. In this study we isolated the extent to which memory for a recently consumed meal influences hunger and fullness over a three-hour period. Before lunch, half of our volunteers were shown 300 ml of soup and half were shown 500 ml. Orthogonal to this, half consumed 300 ml and half consumed 500 ml. This process yielded four separate groups (25 volunteers in each). Independent manipulation of the 'actual' and 'perceived' soup portion was achieved using a computer-controlled peristaltic pump. This was designed to either refill or draw soup from a soup bowl in a covert manner. Immediately after lunch, self-reported hunger was influenced by the actual and not the perceived amount of soup consumed. However, two and three hours after meal termination this pattern was reversed - hunger was predicted by the perceived amount and not the actual amount. Participants who thought they had consumed the larger 500-ml portion reported significantly less hunger. This was also associated with an increase in the 'expected satiation' of the soup 24-hours later. For the first time, this manipulation exposes the independent and important contribution of memory processes to satiety. Opportunities exist to capitalise on this finding to reduce energy intake in humans.

Microwave Photonic Architecture for Direction Finding of LPI Emitters: Front End Analog Circuit Design and Component Characterization

DTIC Science & Technology

2016-09-01

design to control the phase shifters was complex, and the calibration process was time consuming. During the redesign process, we carried out...signals in time domain with a maximum sampling frequency of 20 Giga samples per second. In the previous tests of the design , the performance of...PHOTONIC ARCHITECTURE FOR DIRECTION FINDING OF LPI EMITTERS: FRONT-END ANALOG CIRCUIT DESIGN AND COMPONENT CHARACTERIZATION by Chew K. Tan

The Minimal Cost of Life in Space

NASA Astrophysics Data System (ADS)

Drysdale, A.; Rutkze, C.; Albright, L.; Ladue, R.

Life in space requires protection from the external environment, provision of a suitable internal environment, provision of consumables to maintain life, and removal of wastes. Protection from the external environment will mainly require shielding from radiation and meteoroids. Provision of a suitable environment inside the spacecraft will require provision of suitable air pressure and composition, temperature, and protection from environmental toxins (trace contaminants) and pathogenic micro-organisms. Gravity may be needed for longer missions to avoid excessive changes such as decalcification and muscle degeneration. Similarly, the volume required per crewmember will increase as the mission duration increases. Consumables required include oxygen, food, and water. Nitrogen might be required, depending on the total pressure and non-metabolic losses. We normally provide these consumables from the Earth, with a greater or lesser degree of regeneration. In principle, all consumables can be regenerated. Water and air are easiest to regenerate. At the present time, food can only be regenerated by using plants, and higher plants at that. Waste must be removed, including carbon dioxide and other metabolic waste as well as trash such as food packaging, filters, and expended spare parts. This can be done by dumping or regeneration. The minimal cost of life in space would be to use a synthesis process or system to regenerate all consumables from wastes. As the efficiency of the various processes rises, the minimal cost of life support will fall. However, real world regeneration requires significant equipment, power, and crew time. Make-up will be required for those items that cannot be economically regenerated. For very inefficient processes, it might be cheaper to ship all or part of the consumables. We are currently far down the development curve, and for short missions it is cheaper to ship consumables. For longer duration missions, greater closure is cost effective. However, there will always be losses and inefficiencies. An example is provided using the Cornell Controlled Environment Agriculture experimental unit to define the real-world state of the art. This unit produces lettuce on a small but commercial scale. System inputs and outputs are well documented. Some changes can be identified that could be made to reduce the cost of such a system in space. Other changes would be speculative. The mission impact of such a plant production system is estimated using an equivalent system mass approach.

Use of Existing CAD Models for Radiation Shielding Analysis

NASA Technical Reports Server (NTRS)

Lee, K. T.; Barzilla, J. E.; Wilson, P.; Davis, A.; Zachman, J.

2015-01-01

The utility of a radiation exposure analysis depends not only on the accuracy of the underlying particle transport code, but also on the accuracy of the geometric representations of both the vehicle used as radiation shielding mass and the phantom representation of the human form. The current NASA/Space Radiation Analysis Group (SRAG) process to determine crew radiation exposure in a vehicle design incorporates both output from an analytic High Z and Energy Particle Transport (HZETRN) code and the properties (i.e., material thicknesses) of a previously processed drawing. This geometry pre-process can be time-consuming, and the results are less accurate than those determined using a Monte Carlo-based particle transport code. The current work aims to improve this process. Although several Monte Carlo programs (FLUKA, Geant4) are readily available, most use an internal geometry engine. The lack of an interface with the standard CAD formats used by the vehicle designers limits the ability of the user to communicate complex geometries. Translation of native CAD drawings into a format readable by these transport programs is time consuming and prone to error. The Direct Accelerated Geometry -United (DAGU) project is intended to provide an interface between the native vehicle or phantom CAD geometry and multiple particle transport codes to minimize problem setup, computing time and analysis error.

Error image aware content restoration

NASA Astrophysics Data System (ADS)

Choi, Sungwoo; Lee, Moonsik; Jung, Byunghee

2015-12-01

As the resolution of TV significantly increased, content consumers have become increasingly sensitive to the subtlest defect in TV contents. This rising standard in quality demanded by consumers has posed a new challenge in today's context where the tape-based process has transitioned to the file-based process: the transition necessitated digitalizing old archives, a process which inevitably produces errors such as disordered pixel blocks, scattered white noise, or totally missing pixels. Unsurprisingly, detecting and fixing such errors require a substantial amount of time and human labor to meet the standard demanded by today's consumers. In this paper, we introduce a novel, automated error restoration algorithm which can be applied to different types of classic errors by utilizing adjacent images while preserving the undamaged parts of an error image as much as possible. We tested our method to error images detected from our quality check system in KBS(Korean Broadcasting System) video archive. We are also implementing the algorithm as a plugin of well-known NLE(Non-linear editing system), which is a familiar tool for quality control agent.

12 CFR Appendix A to Part 343 - Consumer Grievance Process

Code of Federal Regulations, 2010 CFR

2010-01-01

... POLICY CONSUMER PROTECTION IN SALES OF INSURANCE Pt. 343, App. A Appendix A to Part 343—Consumer... Consumer Protection (DSC), Federal Deposit Insurance Corporation, at the following address: 550 17th Street... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Consumer Grievance Process A Appendix A to Part...

Sensory shelf life estimation of minimally processed lettuce considering two stages of consumers' decision-making process.

PubMed

Ares, Gastón; Giménez, Ana; Gámbaro, Adriana

2008-01-01

The aim of the present work was to study the influence of context, particularly the stage of the decision-making process (purchase vs consumption stage), on sensory shelf life of minimally processed lettuce. Leaves of butterhead lettuce were placed in common polypropylene bags and stored at 5, 10 and 15 degrees C. Periodically, a panel of six assessors evaluated the appearance of the samples, and a panel of 40 consumers evaluated their appearance and answered "yes" or "no" to the questions: "Imagine you are in a supermarket, you want to buy a minimally processed lettuce, and you find a package of lettuce with leaves like this, would you normally buy it?" and "Imagine you have this leaf of lettuce stored in your refrigerator, would you normally consume it?". Survival analysis was used to calculate the shelf lives of minimally processed lettuce, considering both decision-making stages. Shelf lives estimated considering rejection to purchase were significantly lower than those estimated considering rejection to consume. Therefore, in order to be conservative and assure the products' quality, shelf life should be estimated considering consumers' rejection to purchase instead of rejection to consume, as traditionally has been done. On the other hand, results from logistic regressions of consumers' rejection percentage as a function of the evaluated appearance attributes suggested that consumers considered them differently while deciding whether to purchase or to consume minimally processed lettuce.

Critical Thinking Outcomes of Computer-Assisted Instruction versus Written Nursing Process.

ERIC Educational Resources Information Center

Saucier, Bonnie L.; Stevens, Kathleen R.; Williams, Gail B.

2000-01-01

Nursing students (n=43) who used clinical case studies via computer-assisted instruction (CAI) were compared with 37 who used the written nursing process (WNP). California Critical Thinking Skills Test results did not show significant increases in critical thinking. The WNP method was more time consuming; the CAI group was more satisfied. Use of…

A Process for Reviewing and Evaluating Generated Test Items

ERIC Educational Resources Information Center

Gierl, Mark J.; Lai, Hollis

2016-01-01

Testing organization needs large numbers of high-quality items due to the proliferation of alternative test administration methods and modern test designs. But the current demand for items far exceeds the supply. Test items, as they are currently written, evoke a process that is both time-consuming and expensive because each item is written,…

Automatic detection of health changes using statistical process control techniques on measured transfer times of elderly.

PubMed

Baldewijns, Greet; Luca, Stijn; Nagels, William; Vanrumste, Bart; Croonenborghs, Tom

2015-01-01

It has been shown that gait speed and transfer times are good measures of functional ability in elderly. However, data currently acquired by systems that measure either gait speed or transfer times in the homes of elderly people require manual reviewing by healthcare workers. This reviewing process is time-consuming. To alleviate this burden, this paper proposes the use of statistical process control methods to automatically detect both positive and negative changes in transfer times. Three SPC techniques: tabular CUSUM, standardized CUSUM and EWMA, known for their ability to detect small shifts in the data, are evaluated on simulated transfer times. This analysis shows that EWMA is the best-suited method with a detection accuracy of 82% and an average detection time of 9.64 days.

I Will Do It If I Enjoy It! The Moderating Effect of Seeking Sensory Pleasure When Exposed to Participatory CSR Campaigns

PubMed Central

Ruiz de Maya, Salvador; Lardín-Zambudio, Rafaela; López-López, Inés

2016-01-01

In an attempt to gain differentiation, companies are allocating resources to corporate social responsibility (CSR) initiatives. At the same time, they are giving consumers a more active role in the process of creating value. In this sense, consumer participation represents a new approach to gain competitive advantage. However, the effectiveness of consumer participation in CSR campaigns still remains unknown. With the purpose of shedding light on this issue, this paper shows that participatory CSR campaigns lead to greater consumer perceptions of CSR, which in turn results in more favorable attitudes toward the company. Furthermore, the effect is stronger for sensory pleasure seekers, whose involvement with the experience is greater. The findings contribute to the CSR literature and reveal important implications for marketers. PMID:26779070

Not just for consumers: context effects are fundamental to decision making.

PubMed

Trueblood, Jennifer S; Brown, Scott D; Heathcote, Andrew; Busemeyer, Jerome R

2013-06-01

Context effects--preference changes that depend on the availability of other options--have attracted a great deal of attention among consumer researchers studying high-level decision tasks. In the experiments reported here, we showed that these effects also arise in simple perceptual-decision-making tasks. This finding casts doubt on explanations limited to consumer choice and high-level decisions, and it indicates that context effects may be amenable to a general explanation at the level of the basic decision process. We demonstrated for the first time that three important context effects from the preferential-choice literature--similarity, attraction, and compromise effects--all occurred within a single perceptual-decision task. Not only do our results challenge previous explanations for context effects proposed by consumer researchers, but they also challenge the choice rules assumed in theories of perceptual decision making.

77 FR 17460 - Multistakeholder Process To Develop Consumer Data Privacy Codes of Conduct

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-26

.... 120214135-2203-02] RIN 0660-XA27 Multistakeholder Process To Develop Consumer Data Privacy Codes of Conduct... request for public comments on the multistakeholder process to develop consumer data privacy codes of...-multistakeholder-process without change. All personal identifying information (for example, name, address...

Managed care for Medicare: some considerations in designing effective information provision programs.

PubMed

Jayanti, R K

2001-01-01

Consumer information-processing theory provides a useful framework for policy makers concerned with regulating information provided by managed care organizations. The assumption that consumers are rational information processors and providing more information is better is questioned in this paper. Consumer research demonstrates that when faced with an uncertain decision, consumers adopt simplifying strategies leading to sub-optimal choices. A discussion on how consumers process risk information and the effects of various informational formats on decision outcomes is provided. Categorization theory is used to propose guidelines with regard to providing effective information to consumers choosing among competing managed care plans. Public policy implications borne out of consumer information-processing theory conclude the article.

State of the art in benefit-risk analysis: consumer perception.

PubMed

Ueland, Ø; Gunnlaugsdottir, H; Holm, F; Kalogeras, N; Leino, O; Luteijn, J M; Magnússon, S H; Odekerken, G; Pohjola, M V; Tijhuis, M J; Tuomisto, J T; White, B C; Verhagen, H

2012-01-01

Benefit and risk perception with respect to food consumption, have been a part of human daily life from beginning of time. In today's society the food chain is long with many different types of actors and low degree of transparency. Making informed food choices where knowledge of benefits and risks is part of the decision making process are therefore complicated for consumers. Thus, to understand how consumers perceive benefits and risks of foods, their importance in relation to quality evaluations are aspects that need to be addressed. The objective of this paper is to discuss state of the art in understanding consumer perceptions of benefits and risks of foods in order to improve understanding of consumer behaviour in the food domain. Risks may be associated with both acute and long term consequences, some of which may have serious effects. Perceived risks are connected to morbidity and mortality along two dimensions relating to unknown risk, and to which extent the risk is dreaded by the consumer. Unfamiliar, uncertain, unknown, uncontrollable, and severe consequences are some factors associated with risk perception. Novel food processing techniques, for instance, score high on several of these parameters and are consequently regarded with suspicion and perceived as risky by consumers. On a daily basis, benefits of foods and food consumption are more important in most consumers' minds than risks. Benefits are often associated with food's ability to assuage hunger, and to provide pleasure through eating and socialising. In addition, two main categories of benefits that are important for acceptance of product innovations are health and environmental benefits. Benefit and risk perception of foods seem to be inversely correlated, so when something is perceived as being highly beneficial, it is correspondingly perceived as having low risk. However, slightly different paths are used in the formation of these perceptions; benefit perception is based on heuristics and experience, while risk perception is to a larger extent the result of cognitive information processing. Consumers are particularly conservative when it comes to perception and acceptance of foods compared to other products. Benefit-risk evaluations tend to be skewed towards acceptance of all that is traditional and well-known (benefits), and rejection or suspicion towards anything that is novel or highly processed (risks) regardless of actual risk. Knowledge of how consumers perceive benefits and risks of foods, may contribute to understanding benefit-risk perception in other areas related to personal, societal or environmental perspectives. Copyright © 2011 Elsevier Ltd. All rights reserved.

Lost in a Giant Database: The Potentials and Pitfalls of Secondary Analysis for Deaf Education

ERIC Educational Resources Information Center

Kluwin, T. N.; Morris, C. S.

2006-01-01

Secondary research or archival research is the analysis of data collected by another person or agency. It offers several advantages, including reduced cost, a less time-consuming research process, and access to larger populations and thus greater generalizability. At the same time, it offers several limitations, including the fact that the…

Observing Ocean Ecosystems with Sonar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matzner, Shari; Maxwell, Adam R.; Ham, Kenneth D.

2016-12-01

We present a real-time processing system for sonar to detect and track animals, and to extract water column biomass statistics in order to facilitate continuous monitoring of an underwater environment. The Nekton Interaction Monitoring System (NIMS) is built to connect to an instrumentation network, where it consumes a real-time stream of sonar data and archives tracking and biomass data.

[Analysis of main risk factors causing foodborne diseases in food catering business].

PubMed

Fan, Yong-xiang; Liu, Xiu-mei; Bao, Yi-dan

2011-06-01

To study main risk factors that cause foodborne diseases in food catering business. Data from references and investigations conducted in food catering units were used to establish models which based on @Risk 4.5 with Monte Carlo method referring to food handling practice model (FHPM) to make risk assessment on factors of food contamination in food catering units. The Beta-Poisson models on dose-response relationship to Salmonella (developed by WHO/FAO and United States Department of Agriculture) and Vibrio parahaemolyticus (developed by US FDA) were used in this article to analyze the dose-response relationship of pathogens. The average probability of food poisoning by consuming Salmonella contaminated cooked meat under refrigeration was 1.96 × 10(-4) which was 1/2800 of the food under non-refrigeration (the average probability of food poisoning was 0.35 at room temperature 25°C). The average probability by consuming 6 hours stored meat under room temperature was 0.11 which was 16 times of 2 hours storage (6.79 × 10(-3)). The average probability by consuming contaminated meat without fully cooking was 1.71 × 10(-4) which was 100 times of consuming fully cooked meat (1.88 × 10(-6)). The probability growth of food poisoning by consuming Vibrio parahaemolyticus contaminated fresh seafood was proportional with contamination level and prevalence. The primary contamination level, storage temperature and time, cooking process and cross contamination are important factors of catering food safety.

Do pig farmers preferences bias consumer choice for pork? Response to critique of the pork preference studies.

PubMed

Ngapo, T M; Fortin, J; Martin, J-F

2010-08-01

Québec consumers and pig farmers selected their preferred chop from 16 images that had been modified to give 16 treatments: two levels each of fat cover, colour, marbling and drip. The selection process was repeated eight times from different groups of chops. Fat cover (47% preferred lean) and colour (44%, light red) were the most frequently chosen characteristics. No significant differences were observed between farmers and consumers preferences (chi(2) test, P<0.05). Two preference-based clusters were found; 41% preferring dark red, lean meat and 59%, light red, lean meat, without marbling or drip. Choice-based clusters showed no significant links with either individual socio-demographic items, including pig farmer as occupation, or the three socio-demographic-based clusters observed (chi(2) test, P<0.05). No evidence was found to suggest that the choices of pig farmers differed from those of consumers and, therefore, inclusion of pig farmers in consumer panels would not bias consumer choice for pork. Crown Copyright (c) 2010. Published by Elsevier Ltd. All rights reserved.

Optimized Laplacian image sharpening algorithm based on graphic processing unit

NASA Astrophysics Data System (ADS)

Ma, Tinghuai; Li, Lu; Ji, Sai; Wang, Xin; Tian, Yuan; Al-Dhelaan, Abdullah; Al-Rodhaan, Mznah

2014-12-01

In classical Laplacian image sharpening, all pixels are processed one by one, which leads to large amount of computation. Traditional Laplacian sharpening processed on CPU is considerably time-consuming especially for those large pictures. In this paper, we propose a parallel implementation of Laplacian sharpening based on Compute Unified Device Architecture (CUDA), which is a computing platform of Graphic Processing Units (GPU), and analyze the impact of picture size on performance and the relationship between the processing time of between data transfer time and parallel computing time. Further, according to different features of different memory, an improved scheme of our method is developed, which exploits shared memory in GPU instead of global memory and further increases the efficiency. Experimental results prove that two novel algorithms outperform traditional consequentially method based on OpenCV in the aspect of computing speed.

Study on Influencing Factor Analysis and Application of Consumer Mobile Commerce Acceptance

NASA Astrophysics Data System (ADS)

Li, Gaoguang; Lv, Tingjie

Mobile commerce (MC) refers to e-commerce activities carried out using a mobile device such as a phone or PDA. With new technology, MC will be rapidly growing in the near future. At the present time, what factors making consumer accept MC and what MC applications are acceptable by consumers are two of hot issues both for MC providers and f or MC researchers. This study presents a proposed MC acceptance model that integrates perceived playfulness, perceived risk and cost into the TAM to study which factors affect consumer MC acceptance. The proposed model includes five variables, namely perceived risk, cost, perceived usefulness, perceived playfulness, perceived ease of use, perceived playfulness. Then, using analytic hierarchy process (AHP) to calculate weight of criteria involved in proposed model. Finally, the study utilizes fuzzy comprehensive evaluation method to evaluate MC applications accepted possibility, and then a MC application is empirically tested using data collected from a survey of MC consumers.

Mosai-Zines.

ERIC Educational Resources Information Center

Lagattuta, Nunzio

2000-01-01

Discusses an art project in which students, using a photograph of a favorite person as a guide, create a paper mosaic with small pieces of paper from magazines, catalogues, and brochures. Describes the process of creating the mosaics. Warns that the project is time consuming. (CMK)

Advances in ingredient and processing systems for meat and meat products.

PubMed

Weiss, Jochen; Gibis, Monika; Schuh, Valerie; Salminen, Hanna

2010-09-01

Changes in consumer demand of meat products as well as increased global competition are causing an unprecedented spur in processing and ingredient system developments within the meat manufacturing sector. Consumers demand healthier meat products that are low in salt, fat, cholesterol, nitrites and calories in general and contain in addition health-promoting bioactive components such as for example carotenoids, unsaturated fatty acids, sterols, and fibers. On the other hand, consumers expect these novel meat products with altered formulations to taste, look and smell the same way as their traditionally formulated and processed counterparts. At the same time, competition is forcing the meat processing industry to use the increasingly expensive raw material "meat" more efficiently and produce products at lower costs. With these changes in mind, this article presents a review of novel ingredient systems and processing approaches that are emerging to create high quality, affordable meat products not only in batch mode but also in large-scale continuous processes. Fat replacers, fat profile modification and cholesterol reduction techniques, new texture modifiers and alternative antioxidant and antimicrobial systems are being discussed. Modern processing equipment to establish continuously operating product manufacturing lines and that allow new meat product structures to be created and novel ingredients to be effectively utilized including vacuum fillers, grinders and fine dispersers, and slicers is reviewed in the context of structure creation in meat products. Finally, trends in future developments of ingredient and processing systems for meat products are highlighted.

Testing single point incremental forming molds for thermoforming operations

NASA Astrophysics Data System (ADS)

Afonso, Daniel; de Sousa, Ricardo Alves; Torcato, Ricardo

2016-10-01

Low pressure polymer processing processes as thermoforming or rotational molding use much simpler molds then high pressure processes like injection. However, despite the low forces involved with the process, molds manufacturing for this operations is still a very material, energy and time consuming operation. The goal of the research is to develop and validate a method for manufacturing plastically formed sheets metal molds by single point incremental forming (SPIF) operation for thermoforming operation. Stewart platform based SPIF machines allow the forming of thick metal sheets, granting the required structural stiffness for the mold surface, and keeping the short lead time manufacture and low thermal inertia.

78 FR 30934 - Certain Consumer Electronics With Display and Processing Capabilities; Notice of Receipt of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-23

... INTERNATIONAL TRADE COMMISSION [Docket No 2956] Certain Consumer Electronics With Display and... the U.S. International Trade Commission has received a complaint entitled Certain Consumer Electronics... consumer electronics with display and processing capabilities. The complaint names as respondents Panasonic...

Health care knowledge and consumer learning: the case of direct-to-consumer drug advertising.

PubMed

Delbaere, Marjorie; Smith, Malcolm C

2006-01-01

This research develops a framework for understanding how consumers process health-related information and interact with their caregivers. The context is direct-to-consumer (DTC) advertising by pharmaceutical companies in North America. This theoretical research presents a research framework and focuses on the presentation of information in advertisements, consumer-learning processes, consumer utilization of health care knowledge, and bias in perceived risk. The paper proposes that consumers who lack expertise with prescription drugs learn from DTC ads differently than those with expertise. Further, it is proposed that consumers also process the information in DTC ads differently depending on the perceived effectiveness of the drug being advertised, and ultimately utilize the knowledge taken from the ads in many different ways, some of which may appear irrational to health care providers. By understanding how consumers interpret and learn from DTC ads, health care organizations and providers may be able to improve health care delivery and consumer outcomes.

Dual-Task Processing When Task 1 Is Hard and Task 2 Is Easy: Reversed Central Processing Order?

ERIC Educational Resources Information Center

Leonhard, Tanja; Fernandez, Susana Ruiz; Ulrich, Rolf; Miller, Jeff

2011-01-01

Five psychological refractory period (PRP) experiments were conducted with an especially time-consuming first task (Experiments 1, 3, and 5: mental rotation; Experiments 2 and 4: memory scanning) and with equal emphasis on the first task and on the second (left-right tone judgment). The standard design with varying stimulus onset asynchronies…

Automatic Item Generation: A More Efficient Process for Developing Mathematics Achievement Items?

ERIC Educational Resources Information Center

Embretson, Susan E.; Kingston, Neal M.

2018-01-01

The continual supply of new items is crucial to maintaining quality for many tests. Automatic item generation (AIG) has the potential to rapidly increase the number of items that are available. However, the efficiency of AIG will be mitigated if the generated items must be submitted to traditional, time-consuming review processes. In two studies,…

Integrated Data Capturing Requirements for 3d Semantic Modelling of Cultural Heritage: the Inception Protocol

NASA Astrophysics Data System (ADS)

Di Giulio, R.; Maietti, F.; Piaia, E.; Medici, M.; Ferrari, F.; Turillazzi, B.

2017-02-01

The generation of high quality 3D models can be still very time-consuming and expensive, and the outcome of digital reconstructions is frequently provided in formats that are not interoperable, and therefore cannot be easily accessed. This challenge is even more crucial for complex architectures and large heritage sites, which involve a large amount of data to be acquired, managed and enriched by metadata. In this framework, the ongoing EU funded project INCEPTION - Inclusive Cultural Heritage in Europe through 3D semantic modelling proposes a workflow aimed at the achievements of efficient 3D digitization methods, post-processing tools for an enriched semantic modelling, web-based solutions and applications to ensure a wide access to experts and non-experts. In order to face these challenges and to start solving the issue of the large amount of captured data and time-consuming processes in the production of 3D digital models, an Optimized Data Acquisition Protocol (DAP) has been set up. The purpose is to guide the processes of digitization of cultural heritage, respecting needs, requirements and specificities of cultural assets.

Nontoxic chemical process for in situ permeability enhancement and accelerated decontamination of fine-grain subsurface sediments

DOEpatents

Kansa, E.J.; Wijesinghe, A.M.; Viani, B.E.

1997-01-14

The remediation of heterogeneous subsurfaces is extremely time consuming and expensive with current and developing technologies. Although such technologies can adequately remove contaminants in the high hydraulic conductivity, coarse-grained sediments, they cannot access the contaminated low hydraulic conductivity fine-grained sediments. The slow bleed of contaminants from the fine-grained sediments is the primary reason why subsurface remediation is so time-consuming and expensive. This invention addresses the problem of remediating contaminated fine-grained sediments. It is intended that, in the future, a heterogeneous site be treated by a hybrid process that first remediates the high hydraulic conductivity, coarse-grained sediments, to be followed by the process, described in this invention, to treat the contaminated low hydraulic conductivity fine-grained sediments. The invention uses cationic flocculants and organic solvents to collapse the swelling negative double layer surrounding water saturated clay particles, causing a flocculated, cracked clay structure. The modification of the clay fabric in fine-grained sediments dramatically increases the hydraulic conductivity of previously very tight clays many orders of magnitude. 8 figs.

Nontoxic chemical process for in situ permeability enhancement and accelerated decontamination of fine-grain subsurface sediments

DOEpatents

Kansa, Edward J.; Wijesinghe, Ananda M.; Viani, Brian E.

1997-01-01

The remediation of heterogeneous subsurfaces is extremely time consuming and expensive with current and developing technologies. Although such technologies can adequately remove contaminants in the high hydraulic conductivity, coarse-grained sediments, they cannot access the contaminated low hydraulic conductivity fine-grained sediments. The slow bleed of contaminants from the fine-grained sediments is the primary reason why subsurface remediation is so time-consuming and expensive. This invention addresses the problem of remediating contaminated fine-grained sediments. It is intended that, in the future, a heterogeneous site be treated by a hybrid process that first remediates the high hydraulic conductivity, coarse-grained sediments, to be followed by the process, described in this invention, to treat the contaminated low hydraulic conductivity fine-grained sediments. The invention uses cationic flocculents and organic solvents to collapse the swelling negative double layer surrounding water saturated clay particles, causing a flocculated, cracked clay structure. The modification of the clay fabric in fine-grained sediments dramatically increases the hydraulic conductivity of previously very tight clays many orders of magnitude.

Episodic Memory and Appetite Regulation in Humans

PubMed Central

Brunstrom, Jeffrey M.; Burn, Jeremy F.; Sell, Nicola R.; Collingwood, Jane M.; Rogers, Peter J.; Wilkinson, Laura L.; Hinton, Elanor C.; Maynard, Olivia M.; Ferriday, Danielle

2012-01-01

Psychological and neurobiological evidence implicates hippocampal-dependent memory processes in the control of hunger and food intake. In humans, these have been revealed in the hyperphagia that is associated with amnesia. However, it remains unclear whether ‘memory for recent eating’ plays a significant role in neurologically intact humans. In this study we isolated the extent to which memory for a recently consumed meal influences hunger and fullness over a three-hour period. Before lunch, half of our volunteers were shown 300 ml of soup and half were shown 500 ml. Orthogonal to this, half consumed 300 ml and half consumed 500 ml. This process yielded four separate groups (25 volunteers in each). Independent manipulation of the ‘actual’ and ‘perceived’ soup portion was achieved using a computer-controlled peristaltic pump. This was designed to either refill or draw soup from a soup bowl in a covert manner. Immediately after lunch, self-reported hunger was influenced by the actual and not the perceived amount of soup consumed. However, two and three hours after meal termination this pattern was reversed - hunger was predicted by the perceived amount and not the actual amount. Participants who thought they had consumed the larger 500-ml portion reported significantly less hunger. This was also associated with an increase in the ‘expected satiation’ of the soup 24-hours later. For the first time, this manipulation exposes the independent and important contribution of memory processes to satiety. Opportunities exist to capitalise on this finding to reduce energy intake in humans. PMID:23227200

Cassava processing, consumption, and cyanide toxicity.

PubMed

Adewusi, S R; Akindahunsi, A A

1994-09-01

The frequency of cassava consumption was investigated among three groups of people representing students from traditional and nontraditional cassava-consuming environments and cassava processors. Of these, 64% of the students at Obafemi Awolowo University, Ile-Ife, 38% of those at the Federal University of Technology, Akure, and 44% of the cassava processors consumed cassava products at least once a day, while 4, 35, and 28% of the groups, respectively, were moderate consumers (4-6 times a week). The serum thiocyanate level of the processors was significantly higher (0.57 mg/dl) than those of the students (0.38 mg/dl), but there was no significant difference in the urinary thiocyanate level of the three groups. Analysis of cassava and its intermediate and final products for free cyanide, acetone cyanohydrin, and intact glucosides during the production of such cassava products as gari, fufu, and lafun revealed that while the finished products might be safe for human consumption, the workers were probably exposed at different stages of processing to nondietary sources of cyanide.

Advanced Decontamination Technologies: High Hydrostatic Pressure on Meat Products

NASA Astrophysics Data System (ADS)

Garriga, Margarita; Aymerich, Teresa

The increasing demand for “natural” foodstuffs, free from chemical additives, and preservatives has triggered novel approaches in food technology developments. In the last decade, practical use of high-pressure processing (HPP) made this emerging non-thermal technology very attractive from a commercial point of view. Despite the fact that the investment is still high, the resulting value-added products, with an extended and safe shelf-life, will fulfil the wishes of consumers who prefer preservative-free minimally processed foods, retaining sensorial characteristics of freshness. Moreover, unlike thermal treatment, pressure treatment is not time/mass dependant, thus reducing the time of processing.

12 CFR Appendix A to Subpart H of... - Consumer Grievance Process

Code of Federal Regulations, 2011 CFR

2011-01-01

... of the bank has violated the requirements of this subpart should contact the Consumer Complaints... 12 Banks and Banking 2 2011-01-01 2011-01-01 false Consumer Grievance Process A Appendix A to... SYSTEM MEMBERSHIP OF STATE BANKING INSTITUTIONS IN THE FEDERAL RESERVE SYSTEM (REGULATION H) Consumer...

12 CFR Appendix A to Subpart H of... - Consumer Grievance Process

Code of Federal Regulations, 2012 CFR

2012-01-01

... of the bank has violated the requirements of this subpart should contact the Consumer Complaints... 12 Banks and Banking 2 2012-01-01 2012-01-01 false Consumer Grievance Process A Appendix A to... SYSTEM MEMBERSHIP OF STATE BANKING INSTITUTIONS IN THE FEDERAL RESERVE SYSTEM (REGULATION H) Consumer...

12 CFR Appendix A to Subpart H of... - Consumer Grievance Process

Code of Federal Regulations, 2013 CFR

2013-01-01

... of the bank has violated the requirements of this subpart should contact the Consumer Complaints... 12 Banks and Banking 2 2013-01-01 2013-01-01 false Consumer Grievance Process A Appendix A to... SYSTEM MEMBERSHIP OF STATE BANKING INSTITUTIONS IN THE FEDERAL RESERVE SYSTEM (REGULATION H) Consumer...

12 CFR Appendix A to Subpart H of... - Consumer Grievance Process

Code of Federal Regulations, 2014 CFR

2014-01-01

... of the bank has violated the requirements of this subpart should contact the Consumer Complaints... 12 Banks and Banking 2 2014-01-01 2014-01-01 false Consumer Grievance Process A Appendix A to... SYSTEM MEMBERSHIP OF STATE BANKING INSTITUTIONS IN THE FEDERAL RESERVE SYSTEM (REGULATION H) Consumer...

Consumer Awareness and Willingness to Pay for High-Pressure Processing of Ready-to-Eat Food

ERIC Educational Resources Information Center

Hicks, Doris T.; Pivarnik, Lori F.; McDermott, Ryan; Richard, Nicole; Hoover, Dallas G.; Kniel, Kalmia E.

2009-01-01

Commercial, nonthermal processing of food, such as high hydrostatic-pressure processing (HPP), has increased. The safety and quality of foods produced by HPP has not been well communicated to the public. An online, nationwide consumer survey was implemented to assess awareness of alternative food processing technologies, consumer food safety…

Mobile Ultrasound Plane Wave Beamforming on iPhone or iPad using Metal- based GPU Processing

NASA Astrophysics Data System (ADS)

Hewener, Holger J.; Tretbar, Steffen H.

Mobile and cost effective ultrasound devices are being used in point of care scenarios or the drama room. To reduce the costs of such devices we already presented the possibilities of consumer devices like the Apple iPad for full signal processing of raw data for ultrasound image generation. Using technologies like plane wave imaging to generate a full image with only one excitation/reception event the acquisition times and power consumption of ultrasound imaging can be reduced for low power mobile devices based on consumer electronics realizing the transition from FPGA or ASIC based beamforming into more flexible software beamforming. The massive parallel beamforming processing can be done with the Apple framework "Metal" for advanced graphics and general purpose GPU processing for the iOS platform. We were able to integrate the beamforming reconstruction into our mobile ultrasound processing application with imaging rates up to 70 Hz on iPad Air 2 hardware.

[Study on the optimal extraction process of chaihushugan powder].

PubMed

Wang, Chun-yan; Zhang, Wan-ming; Zhang, Dan-shen; An, Fang; Tian, Jia-ming

2009-11-01

To study the optimal extraction process of chaihushugan powder by orthogonal design. RP-HPLC method was developed for the determination of saikosaponin a, ferulic acid, hesperidin and paeoniflorin in chaihushugan powder. The contents of the components and the extraction yield were selected as assessment indices. Four factors were study by L9 (3(4)), including the alcohol concentration, amount of alcohol, duration of extraction and times of extraction. The optimal extracting condition was 80% alcohol consumed as 10 times of crude herb amount, and extracting two times for 90 min each time. This study supplies theoretical base for the development of chaihushugan powder formulation.

Celiac Disease Testing (for Health Care Professionals)

MedlinePlus

... diet. tTG The tTG-IgA test is an enzyme-linked immunosorbent assay (ELISA) test. The tTG-IgA test is the preferred ... a more expensive and time-consuming process than ELISA testing. In addition, the EMA test is qualitative, ...

A Chemical Properties Simulator to Support Integrated Environmental Modeling

EPA Science Inventory

Users of Integrated Environmental Modeling (IEM) systems are responsible for defining individual chemicals and their properties, a process that is time-consuming at best and overwhelming at worst, especially for new chemicals with new structures. A software tool is needed to allo...

Sourcing Life Cycle Inventory Data

EPA Science Inventory

The collection and validation of quality lifecycle inventory (LCI) data can be the most difficult and time-consuming aspect of developing a life cycle assessment (LCA). Large amounts of process and production data are needed to complete the LCI. For many studies, the LCA analyst ...

On the Character of Consciousness

PubMed Central

Annila, Arto

2016-01-01

The human brain is a particularly demanding system to infer its nature from observations. Thus, there is on one hand plenty of room for theorizing and on the other hand a pressing need for a rigorous theory. We apply statistical mechanics of open systems to describe the brain as a hierarchical system in consuming free energy in least time. This holistic tenet accounts for cellular metabolism, neuronal signaling, cognitive processes all together, or any other process by a formal equation of motion that extends down to the ultimate precision of one quantum of action. According to this general thermodynamic theory cognitive processes are no different by their operational and organizational principle from other natural processes. Cognition too will emerge and evolve along path-dependent and non-determinate trajectories by consuming free energy in least time to attain thermodynamic balance within the nervous system itself and with its surrounding systems. Specifically, consciousness can be ascribed to a natural process that integrates various neural networks for coherent consumption of free energy, i.e., for meaningful deeds. The whole hierarchy of integrated systems can be formally summed up to thermodynamic entropy. The holistic tenet provides insight to the character of consciousness also by acknowledging awareness in other systems at other levels of nature's hierarchy. PMID:27065819

On the Character of Consciousness.

PubMed

Annila, Arto

2016-01-01

The human brain is a particularly demanding system to infer its nature from observations. Thus, there is on one hand plenty of room for theorizing and on the other hand a pressing need for a rigorous theory. We apply statistical mechanics of open systems to describe the brain as a hierarchical system in consuming free energy in least time. This holistic tenet accounts for cellular metabolism, neuronal signaling, cognitive processes all together, or any other process by a formal equation of motion that extends down to the ultimate precision of one quantum of action. According to this general thermodynamic theory cognitive processes are no different by their operational and organizational principle from other natural processes. Cognition too will emerge and evolve along path-dependent and non-determinate trajectories by consuming free energy in least time to attain thermodynamic balance within the nervous system itself and with its surrounding systems. Specifically, consciousness can be ascribed to a natural process that integrates various neural networks for coherent consumption of free energy, i.e., for meaningful deeds. The whole hierarchy of integrated systems can be formally summed up to thermodynamic entropy. The holistic tenet provides insight to the character of consciousness also by acknowledging awareness in other systems at other levels of nature's hierarchy.

78 FR 38072 - Certain Consumer Electronics With Display and Processing Capabilities; Institution of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-884] Certain Consumer Electronics With Display and... electronics with display and processing capabilities by reason of infringement of U.S. Patent No. 6,650,327... after importation of certain consumer electronics with display and processing capabilities by reason of...

The influence of social involvement, neighborhood aesthetics, and community garden participation on fruit and vegetable consumption.

PubMed

Litt, Jill S; Soobader, Mah-J; Turbin, Mark S; Hale, James W; Buchenau, Michael; Marshall, Julie A

2011-08-01

We considered the relationship between an urban adult population's fruit and vegetable consumption and several selected social and psychological processes, beneficial aesthetic experiences, and garden participation. We conducted a population-based survey representing 436 residents across 58 block groups in Denver, Colorado, from 2006 to 2007. We used multilevel statistical models to evaluate the survey data. Neighborhood aesthetics, social involvement, and community garden participation were significantly associated with fruit and vegetable intake. Community gardeners consumed fruits and vegetables 5.7 times per day, compared with home gardeners (4.6 times per day) and nongardeners (3.9 times per day). Moreover, 56% of community gardeners met national recommendations to consume fruits and vegetables at least 5 times per day, compared with 37% of home gardeners and 25% of nongardeners. Our study results shed light on neighborhood processes that affect food-related behaviors and provides insights about the potential of community gardens to affect these behaviors. The qualities intrinsic to community gardens make them a unique intervention that can narrow the divide between people and the places where food is grown and increase local opportunities to eat better.

The Influence of Social Involvement, Neighborhood Aesthetics, and Community Garden Participation on Fruit and Vegetable Consumption

PubMed Central

Soobader, Mah-J.; Turbin, Mark S.; Hale, James W.; Buchenau, Michael; Marshall, Julie A.

2011-01-01

Objectives. We considered the relationship between an urban adult population's fruit and vegetable consumption and several selected social and psychological processes, beneficial aesthetic experiences, and garden participation. Methods. We conducted a population-based survey representing 436 residents across 58 block groups in Denver, Colorado, from 2006 to 2007. We used multilevel statistical models to evaluate the survey data. Results. Neighborhood aesthetics, social involvement, and community garden participation were significantly associated with fruit and vegetable intake. Community gardeners consumed fruits and vegetables 5.7 times per day, compared with home gardeners (4.6 times per day) and nongardeners (3.9 times per day). Moreover, 56% of community gardeners met national recommendations to consume fruits and vegetables at least 5 times per day, compared with 37% of home gardeners and 25% of nongardeners. Conclusions. Our study results shed light on neighborhood processes that affect food-related behaviors and provides insights about the potential of community gardens to affect these behaviors. The qualities intrinsic to community gardens make them a unique intervention that can narrow the divide between people and the places where food is grown and increase local opportunities to eat better. PMID:21680931

Community representation in hospital decision making: a literature review.

PubMed

Murray, Zoë

2015-06-01

Advancing quality in health services requires structures and processes that are informed by consumer input. Although this agenda is well recognised, few researchers have focussed on the establishment and maintenance of customer input throughout the structures and processes used to produce high-quality, safe care. We present an analysis of literature outlining the barriers and enablers involved in community representation in hospital governance. The review aimed to explore how community representation in hospital governance is achieved. Studies spanning 1997-2012 were analysed using Donabedian' s model of quality systems as a guide for categories of interest: structure, in relation to administration of quality; process, which is particularly concerned with cooperation and culture; and outcome, considered, in this case, to be the achievement of effective community representation on quality of care. There are limited published studies on community representation in hospital governance in Australia. What can be gleaned from the literature is: 1) quality subcommittees set up to assist Hospital Boards are a key structure for involving community representation in decision making around quality of care, and 2) there are a number of challenges to effectively developing the process of community representation in hospital governance: ambiguity and the potential for escalated indecision; inadequate value and consideration given to it by decision makers resulting in a lack of time and resources needed to support the community engagement strategy (time, facilitation, budgets); poor support and attitude amongst staff; and consumer issues, such as feeling isolated and intimidated by expert opinion. The analysis indicates that: quality subcommittees set up to assist boards are a key structure for involving community representation in decision making around quality of care. There are clearly a number of challenges to effectively developing the process of community representation in hospital governance, associated with ambiguity, organisational and consumer issues. For an inclusive agenda to real life, work must be done on understanding the representatives' role and the decision making process, adequately supporting the representational process, and developing organisational cooperation and culture regarding community representation.

16 CFR 610.3 - Streamlined process for requesting annual file disclosures from nationwide specialty consumer...

Code of Federal Regulations, 2010 CFR

2010-01-01

... and prominently posted on any website owned or maintained by the nationwide specialty consumer... by any additional available request methods; and (2) Be designed, funded, implemented, maintained... consumers request while the consumer is in the process of making a request; (B) For a website request method...

12 CFR Appendix A to Part 536 - Consumer Grievance Process

Code of Federal Regulations, 2013 CFR

2013-01-01

..., or telephone 202-906-6237 or 800-842-6929, or e-mail consumer.complaint@ots.treas.gov. ... 12 Banks and Banking 6 2013-01-01 2012-01-01 true Consumer Grievance Process A Appendix A to Part 536 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN...

12 CFR Appendix A to Part 536 - Consumer Grievance Process

Code of Federal Regulations, 2011 CFR

2011-01-01

..., or telephone 202-906-6237 or 800-842-6929, or e-mail consumer.complaint@ots.treas.gov. ... 12 Banks and Banking 5 2011-01-01 2011-01-01 false Consumer Grievance Process A Appendix A to Part 536 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN...

12 CFR Appendix A to Part 536 - Consumer Grievance Process

Code of Federal Regulations, 2012 CFR

2012-01-01

..., or telephone 202-906-6237 or 800-842-6929, or e-mail consumer.complaint@ots.treas.gov. ... 12 Banks and Banking 6 2012-01-01 2012-01-01 false Consumer Grievance Process A Appendix A to Part 536 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN...

12 CFR Appendix A to Part 536 - Consumer Grievance Process

Code of Federal Regulations, 2014 CFR

2014-01-01

..., or telephone 202-906-6237 or 800-842-6929, or e-mail consumer.complaint@ots.treas.gov. ... 12 Banks and Banking 6 2014-01-01 2012-01-01 true Consumer Grievance Process A Appendix A to Part 536 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY CONSUMER PROTECTION IN...

16 CFR 610.3 - Streamlined process for requesting annual file disclosures from nationwide specialty consumer...

Code of Federal Regulations, 2012 CFR

2012-01-01

... and prominently posted on any website owned or maintained by the nationwide specialty consumer... by any additional available request methods; and (2) Be designed, funded, implemented, maintained... consumers request while the consumer is in the process of making a request; (B) For a website request method...

16 CFR 610.3 - Streamlined process for requesting annual file disclosures from nationwide specialty consumer...

Code of Federal Regulations, 2011 CFR

2011-01-01

... and prominently posted on any website owned or maintained by the nationwide specialty consumer... by any additional available request methods; and (2) Be designed, funded, implemented, maintained... consumers request while the consumer is in the process of making a request; (B) For a website request method...

The Power to drive change: Working together for excellence. Creating a continuously improving consumer engagement framework for excellence in patient-centered care.

PubMed

Ryan, Catherine

2016-01-01

The World Health Organization has acknowledged Patient Safety while receiving hospital care as a serious global public health issue, with patient empowerment and community engagement key to continuously improving safety and quality of care for the best possible clinical and patient outcomes. In Australia, the introduction of ten mandatory National Safety and Quality Health Service Standards in 2011 provided the catalyst for all Australian health facilities to review their systems. Standard 2: Partnering with Consumers required health facilities across Australia to assess commitment to, and capacity for consumer and community engagement and participation. At this time, the Royal Brisbane and Women's Hospital did not have a strategic perspective and understanding, or an organizational structure for engaging with consumers (patients, families, care givers and community members). The concept required a new model to replace the clinician-led model of healthcare historically featured in Australia, with a change in culture and core business. processes to partner with consumers at all levels of the system, from individual patient care through to participating in policy development, health service planning and delivery, and evaluation and measurement processes. The challenge for the hospital was to build a sustainable framework of engagement for a genuine patient-centered model of care informed by best practice, and provide leadership and commitment to developing as an area of excellence in patient engagement and experience. A successful and sustainable framework for consumer and community engagement has been embedded in the hospital, with resultant culture change, achieving accreditation across all core and developmental criteria for the partnering with consumer standards including several Met with Merit ratings.

Divergent trophic levels in two cryptic sibling bat species.

PubMed

Siemers, Björn M; Greif, Stefan; Borissov, Ivailo; Voigt-Heucke, Silke L; Voigt, Christian C

2011-05-01

Changes in dietary preferences in animal species play a pivotal role in niche specialization. Here, we investigate how divergence of foraging behaviour affects the trophic position of animals and thereby their role for ecosystem processes. As a model, we used two closely related bat species, Myotis myotis and M. blythii oxygnathus, that are morphologically very similar and share the same roosts, but show clear behavioural divergence in habitat selection and foraging. Based on previous dietary studies on synanthropic populations in Central Europe, we hypothesised that M. myotis would mainly prey on predatory arthropods (i.e., secondary consumers) while M. blythii oxygnathus would eat herbivorous insects (i.e., primary consumers). We thus expected that the sibling bats would be at different trophic levels. We first conducted a validation experiment with captive bats in the laboratory and measured isotopic discrimination, i.e., the stepwise enrichment of heavy in relation to light isotopes between consumer and diet, in insectivorous bats for the first time. We then tested our trophic level hypothesis in the field at an ancient site of natural coexistence for the two species (Bulgaria, south-eastern Europe) using stable isotope analyses. As predicted, secondary consumer arthropods (carabid beetles; Coleoptera) were more enriched in (15)N than primary consumer arthropods (tettigoniids; Orthoptera), and accordingly wing tissue of M. myotis was more enriched in (15)N than tissue of M. blythii oxygnathus. According to a Bayesian mixing model, M. blythii oxygnathus indeed fed almost exclusively on primary consumers (98%), while M. myotis ate a mix of secondary (50%), but also, and to a considerable extent, primary consumers (50%). Our study highlights that morphologically almost identical, sympatric sibling species may forage at divergent trophic levels, and, thus may have different effects on ecosystem processes.

Collaborating with consumer and community representatives in health and medical research in Australia: results from an evaluation.

PubMed

Payne, Janet M; D'Antoine, Heather A; France, Kathryn E; McKenzie, Anne E; Henley, Nadine; Bartu, Anne E; Elliott, Elizabeth J; Bower, Carol

2011-05-14

To collaborate with consumer and community representatives in the Alcohol and Pregnancy Project from 2006-2008 http://www.ichr.uwa.edu.au/alcoholandpregnancy and evaluate researchers' and consumer and community representatives' perceptions of the process, context and impact of consumer and community participation in the project. We formed two reference groups and sought consumer and community representatives' perspectives on all aspects of the project over a three year period. We developed an evaluation framework and asked consumer and community representatives and researchers to complete a self-administered questionnaire at the end of the project. Fifteen researchers (93.8%) and seven (53.8%) consumer and community representatives completed a questionnaire. Most consumer and community representatives agreed that the process and context measures of their participation had been achieved. Both researchers and consumer and community representatives identified areas for improvement and offered suggestions how these could be improved for future research. Researchers thought consumer and community participation contributed to project outputs and outcomes by enhancing scientific and ethical standards, providing legitimacy and authority, and increasing the project's credibility and participation. They saw it was fundamental to the research process and acknowledged consumer and community representatives for their excellent contribution. Consumer and community representatives were able to directly influence decisions about the research. They thought that consumer and community participation had significant influence on the success of project outputs and outcomes. Consumer and community participation is an essential component of good research practice and contributed to the Alcohol and Pregnancy Project by enhancing research processes, outputs and outcomes, and this participation was valued by community and consumer representatives and researchers. The National Health and Medical Research Council in Australia expects researchers to work in partnership and involve consumer and community representatives in health and medical research, and to evaluate community and consumer participation. It is important to demonstrate whether consumer and community participation makes a difference to health and medical research.

Collaborating with consumer and community representatives in health and medical research in Australia: results from an evaluation

PubMed Central

2011-01-01

Objective To collaborate with consumer and community representatives in the Alcohol and Pregnancy Project from 2006-2008 http://www.ichr.uwa.edu.au/alcoholandpregnancy and evaluate researchers' and consumer and community representatives' perceptions of the process, context and impact of consumer and community participation in the project. Methods We formed two reference groups and sought consumer and community representatives' perspectives on all aspects of the project over a three year period. We developed an evaluation framework and asked consumer and community representatives and researchers to complete a self-administered questionnaire at the end of the project. Results Fifteen researchers (93.8%) and seven (53.8%) consumer and community representatives completed a questionnaire. Most consumer and community representatives agreed that the process and context measures of their participation had been achieved. Both researchers and consumer and community representatives identified areas for improvement and offered suggestions how these could be improved for future research. Researchers thought consumer and community participation contributed to project outputs and outcomes by enhancing scientific and ethical standards, providing legitimacy and authority, and increasing the project's credibility and participation. They saw it was fundamental to the research process and acknowledged consumer and community representatives for their excellent contribution. Consumer and community representatives were able to directly influence decisions about the research. They thought that consumer and community participation had significant influence on the success of project outputs and outcomes. Conclusions Consumer and community participation is an essential component of good research practice and contributed to the Alcohol and Pregnancy Project by enhancing research processes, outputs and outcomes, and this participation was valued by community and consumer representatives and researchers. The National Health and Medical Research Council in Australia expects researchers to work in partnership and involve consumer and community representatives in health and medical research, and to evaluate community and consumer participation. It is important to demonstrate whether consumer and community participation makes a difference to health and medical research. PMID:21569591

Tropical field performance of dual-pass PV tray dryer

NASA Astrophysics Data System (ADS)

Iskandar, A. Noor; Ya'acob, M. E.; Anuar, M. S.

2017-09-01

Solar Photovoltaic technology has become the preferable solution in many countries around the globe to solve the ever increasing energy demand of the consumers. In line with the consumer need, food processing technology has huge potentials of integration with the renewable energy resources especially in drying process which consumes the highest electricity loads. Traditionally, the solar dryer technology was applied in agriculture and food industries utilizing the sun's energy for drying process, but this is highly dependable on the weather condition and surrounding factors. This work shares some field performance of the new design of portable dual-pass PV tray dryer for drying crops in an enclosed system. The dual-pass PV tray dryer encompass a lightweight aluminium box structure with dimensions of 1.1m (L) x 0.6m (W) x 0.2m (H) and can hold a load capacity of 300g - 3kg of crop depending on the types of the crops. Experiments of field performance monitoring were conducted in October -November 2016 which justifies a considerable reduction in time and crops quality improvement when using the dual-pass PV tray dryer as compared to direct-sun drying.

Dual-process theory and consumer response to front-of-package nutrition label formats.

PubMed

Sanjari, S Setareh; Jahn, Steffen; Boztug, Yasemin

2017-11-01

Nutrition labeling literature yields fragmented results about the effect of front-of-package (FOP) nutrition label formats on healthy food choice. Specifically, it is unclear which type of nutrition label format is effective across different shopping situations. To address this gap, the present review investigates the available nutrition labeling literature through the prism of dual-process theory, which posits that decisions are made either quickly and automatically (system 1) or slowly and deliberately (system 2). A systematically performed review of nutrition labeling literature returned 59 papers that provide findings that can be explained according to dual-process theory. The findings of these studies suggest that the effectiveness of nutrition label formats is influenced by the consumer's dominant processing system, which is a function of specific contexts and personal variables (eg, motivation, nutrition knowledge, time pressure, and depletion). Examination of reported findings through a situational processing perspective reveals that consumers might prefer different FOP nutrition label formats in different situations and can exhibit varying responses to the same label format across situations. This review offers several suggestions for policy makers and researchers to help improve current FOP nutrition label formats. © The Author(s) 2017. Published by Oxford University Press on behalf of the International Life Sciences Institute. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

BigDebug: Debugging Primitives for Interactive Big Data Processing in Spark.

PubMed

Gulzar, Muhammad Ali; Interlandi, Matteo; Yoo, Seunghyun; Tetali, Sai Deep; Condie, Tyson; Millstein, Todd; Kim, Miryung

2016-05-01

Developers use cloud computing platforms to process a large quantity of data in parallel when developing big data analytics. Debugging the massive parallel computations that run in today's data-centers is time consuming and error-prone. To address this challenge, we design a set of interactive, real-time debugging primitives for big data processing in Apache Spark, the next generation data-intensive scalable cloud computing platform. This requires re-thinking the notion of step-through debugging in a traditional debugger such as gdb, because pausing the entire computation across distributed worker nodes causes significant delay and naively inspecting millions of records using a watchpoint is too time consuming for an end user. First, BIGDEBUG's simulated breakpoints and on-demand watchpoints allow users to selectively examine distributed, intermediate data on the cloud with little overhead. Second, a user can also pinpoint a crash-inducing record and selectively resume relevant sub-computations after a quick fix. Third, a user can determine the root causes of errors (or delays) at the level of individual records through a fine-grained data provenance capability. Our evaluation shows that BIGDEBUG scales to terabytes and its record-level tracing incurs less than 25% overhead on average. It determines crash culprits orders of magnitude more accurately and provides up to 100% time saving compared to the baseline replay debugger. The results show that BIGDEBUG supports debugging at interactive speeds with minimal performance impact.

Perceptions of meal convenience: the case of at-home evening meals.

PubMed

Jaeger, Sara R; Meiselman, Herbert L

2004-06-01

Perceptions of a range of evening meal situations eaten in the home were explored in a female consumer population. The investigation was carried out using the repertory grid technique and using written scenarios as the research stimuli. The nine scenarios successfully manipulated perceived convenience, time and effort. A consumer-generated vocabulary pertaining to food-related convenience was derived and revealed that while elements of both time and effort contributed to perceived convenience, these two 'dimensions' were highly interdependent. The presence of terms related to planning, shopping, preparation, cooking and clean-up illustrated that all stages in the food provisioning process influenced perceived convenience. Some evidence was established of perceptual differences between individuals varying with respect to convenience orientation in meal preparation.

Categorization of Survey Text Utilizing Natural Language Processing and Demographic Filtering

DTIC Science & Technology

2017-09-01

SURVEY TEXT UTILIZING NATURAL LANGUAGE PROCESSING AND DEMOGRAPHIC FILTERING by Christine M. Cairoli September 2017 Thesis Advisor: Lyn...DATE September 2017 3. REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE CATEGORIZATION OF SURVEY TEXT UTILIZING NATURAL...words) Thousands of Navy survey free text comments are overlooked every year because reading and interpreting comments is expensive, time consuming

International Trade: Rules of Origin

DTIC Science & Technology

2009-03-06

products has been subcontracted to a global manufacturing company that operates in many countries. While some major retailers and brand -name distributors...often the case in today’s global trading environment—determining origin can be a very complex, sometimes subjective, and time-consuming process. U.S...CBP origin determinations, and the effects of the global manufacturing process on ROO. Third, we conclude with some alternatives and options that

Web-Based versus Paper-Based Data Collection for the Evaluation of Teaching Activity: Empirical Evidence from a Case Study

ERIC Educational Resources Information Center

Lalla, Michele; Ferrari, Davide

2011-01-01

The collection of teaching evaluation questionnaires in the traditional paper-and-pencil format is a costly and time-consuming process and yet it is a common assessment practice in many university systems. Web-based data collection would reduce costs and significantly increase the efficiency of the overall evaluation process in numerous ways.…

How to Build the Master Schedule in 10 Easy Steps: A Guide for Secondary School Administrators

ERIC Educational Resources Information Center

Kussin, Steven S.

2007-01-01

This book is an incredibly valuable resource to anyone involved in building a master schedule. The author provides a comprehensive description of the processes involved and makes the reader aware of what needs to be considered and done throughout the process. One of the most time-consuming tasks for school leaders is creating a master schedule…

Modeling Post-Accident Vehicle Egress

DTIC Science & Technology

2013-01-01

interest for military situations may involve rolled-over vehicles for which detailed movement data are not available. In the current design process...test trials. These evaluations are expensive and time-consuming, and are often performed late in the design process when it is too difficult to...alter the design if weaknesses are discovered. Yet, due to the limitations of current software tools, digital human models (DHMs) are not yet widely

Rearing insects on artificial diets

USDA-ARS?s Scientific Manuscript database

Insects are reared in the laboratory for various purposes. They may be reared either on their natural food or artificial diets. Developing artificial diets may be difficult and time consuming but once optimized, artificial diets usually are simple to prepare and easy to use. Because they are process...

A Chemical Properties Simulator to Support Integrated Environmental Modeling (proceeding)

EPA Science Inventory

Users of Integrated Environmental Modeling (IEM) systems are responsible for defining individual chemicals and their properties, a process that is time-consuming at best and overwhelming at worst, especially for new chemicals with new structures. A software tool is needed to allo...

78 FR 37601 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-21

... the Commission receives 2 of the most time-consuming applications annually, 4 applications of medium... of $200,000 on average to engage in the exemptive order application process, including preparation... applications. See also Political Contributions by Certain Investment Advisers, Investment Advisers Act Release...

A noninvasive technique for real-time detection of bruises in apple surface based on machine vision

NASA Astrophysics Data System (ADS)

Zhao, Juan; Peng, Yankun; Dhakal, Sagar; Zhang, Leilei; Sasao, Akira

2013-05-01

Apple is one of the highly consumed fruit item in daily life. However, due to its high damage potential and massive influence on taste and export, the quality of apple has to be detected before it reaches the consumer's hand. This study was aimed to develop a hardware and software unit for real-time detection of apple bruises based on machine vision technology. The hardware unit consisted of a light shield installed two monochrome cameras at different angles, LED light source to illuminate the sample, and sensors at the entrance of box to signal the positioning of sample. Graphical Users Interface (GUI) was developed in VS2010 platform to control the overall hardware and display the image processing result. The hardware-software system was developed to acquire the images of 3 samples from each camera and display the image processing result in real time basis. An image processing algorithm was developed in Opencv and C++ platform. The software is able to control the hardware system to classify the apple into two grades based on presence/absence of surface bruises with the size of 5mm. The experimental result is promising and the system with further modification can be applicable for industrial production in near future.

European consumer attitudes on the associated health benefits of neutraceutical-containing processed meats using Co-enzyme Q10 as a sample functional ingredient.

PubMed

Tobin, Brian D; O'Sullivan, Maurice G; Hamill, Ruth; Kerry, Joseph P

2014-06-01

This study accumulated European consumer attitudes towards processed meats and their use as a functional food. A survey was set up using an online web-application to gather information on consumer perception of processed meats as well as neutraceutical-containing processed meats. 548 responses were obtained and statistical analysis was carried out using a statistical software package. Data was summarized as frequencies for each question and statistical differences analyzed using the Chi-Square statistical test with a significance level of 5% (P<0.05). The majority of consumer attitudes towards processed meat indicate that they are unhealthy products. Most believe that processed meats contain large quantities of harmful chemicals, fat and salt. Consumers were found to be very pro-bioactive compounds in yogurt style products but unsure of their feelings in meat based products, which is likely due to the lack of familiarity to these products. Many of the respondents were willing to consume meat based functional foods but were not willing to pay more for them. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of input data variability on estimations of the equivalent constant temperature time for microbial inactivation by HTST and retort thermal processing.

PubMed

Salgado, Diana; Torres, J Antonio; Welti-Chanes, Jorge; Velazquez, Gonzalo

2011-08-01

Consumer demand for food safety and quality improvements, combined with new regulations, requires determining the processor's confidence level that processes lowering safety risks while retaining quality will meet consumer expectations and regulatory requirements. Monte Carlo calculation procedures incorporate input data variability to obtain the statistical distribution of the output of prediction models. This advantage was used to analyze the survival risk of Mycobacterium avium subspecies paratuberculosis (M. paratuberculosis) and Clostridium botulinum spores in high-temperature short-time (HTST) milk and canned mushrooms, respectively. The results showed an estimated 68.4% probability that the 15 sec HTST process would not achieve at least 5 decimal reductions in M. paratuberculosis counts. Although estimates of the raw milk load of this pathogen are not available to estimate the probability of finding it in pasteurized milk, the wide range of the estimated decimal reductions, reflecting the variability of the experimental data available, should be a concern to dairy processors. Knowledge of the C. botulinum initial load and decimal thermal time variability was used to estimate an 8.5 min thermal process time at 110 °C for canned mushrooms reducing the risk to 10⁻⁹ spores/container with a 95% confidence. This value was substantially higher than the one estimated using average values (6.0 min) with an unacceptable 68.6% probability of missing the desired processing objective. Finally, the benefit of reducing the variability in initial load and decimal thermal time was confirmed, achieving a 26.3% reduction in processing time when standard deviation values were lowered by 90%. In spite of novel technologies, commercialized or under development, thermal processing continues to be the most reliable and cost-effective alternative to deliver safe foods. However, the severity of the process should be assessed to avoid under- and over-processing and determine opportunities for improvement. This should include a systematic approach to consider variability in the parameters for the models used by food process engineers when designing a thermal process. The Monte Carlo procedure here presented is a tool to facilitate this task for the determination of process time at a constant lethal temperature. © 2011 Institute of Food Technologists®

Context-Sensitive Spelling Correction of Consumer-Generated Content on Health Care.

PubMed

Zhou, Xiaofang; Zheng, An; Yin, Jiaheng; Chen, Rudan; Zhao, Xianyang; Xu, Wei; Cheng, Wenqing; Xia, Tian; Lin, Simon

2015-07-31

Consumer-generated content, such as postings on social media websites, can serve as an ideal source of information for studying health care from a consumer's perspective. However, consumer-generated content on health care topics often contains spelling errors, which, if not corrected, will be obstacles for downstream computer-based text analysis. In this study, we proposed a framework with a spelling correction system designed for consumer-generated content and a novel ontology-based evaluation system which was used to efficiently assess the correction quality. Additionally, we emphasized the importance of context sensitivity in the correction process, and demonstrated why correction methods designed for electronic medical records (EMRs) failed to perform well with consumer-generated content. First, we developed our spelling correction system based on Google Spell Checker. The system processed postings acquired from MedHelp, a biomedical bulletin board system (BBS), and saved misspelled words (eg, sertaline) and corresponding corrected words (eg, sertraline) into two separate sets. Second, to reduce the number of words needing manual examination in the evaluation process, we respectively matched the words in the two sets with terms in two biomedical ontologies: RxNorm and Systematized Nomenclature of Medicine -- Clinical Terms (SNOMED CT). The ratio of words which could be matched and appropriately corrected was used to evaluate the correction system's overall performance. Third, we categorized the misspelled words according to the types of spelling errors. Finally, we calculated the ratio of abbreviations in the postings, which remarkably differed between EMRs and consumer-generated content and could largely influence the overall performance of spelling checkers. An uncorrected word and the corresponding corrected word was called a spelling pair, and the two words in the spelling pair were its members. In our study, there were 271 spelling pairs detected, among which 58 (21.4%) pairs had one or two members matched in the selected ontologies. The ratio of appropriate correction in the 271 overall spelling errors was 85.2% (231/271). The ratio of that in the 58 spelling pairs was 86% (50/58), close to the overall ratio. We also found that linguistic errors took up 31.4% (85/271) of all errors detected, and only 0.98% (210/21,358) of words in the postings were abbreviations, which was much lower than the ratio in the EMRs (33.6%). We conclude that our system can accurately correct spelling errors in consumer-generated content. Context sensitivity is indispensable in the correction process. Additionally, it can be confirmed that consumer-generated content differs from EMRs in that consumers seldom use abbreviations. Also, the evaluation method, taking advantage of biomedical ontology, can effectively estimate the accuracy of the correction system and reduce manual examination time.

Belgian and Spanish consumption data and consumer handling practices for fresh fruits and vegetables useful for further microbiological and chemical exposure assessment.

PubMed

Jacxsens, L; Ibañez, I Castro; Gómez-López, V M; Fernandes, J Araujo; Allende, A; Uyttendaele, M; Huybrechts, I

2015-04-01

A consumer survey was organized in Spain and Belgium to obtain consumption data and to gain insight into consumer handling practices for fresh vegetables consumed raw or minimally processed (i.e., heads of leafy greens, bell peppers, tomatoes, fresh herbs, and precut and packed leafy greens) and fruits to be consumed without peeling (i.e., apples, grapes, strawberries, raspberries, other berries, fresh juices, and precut mixed fruit). This information can be used for microbiological and/or chemical food safety research. After extensive cleanup of rough databases for missing and extreme values and age correction, information from 583 respondents from Spain and 1,605 respondents from Belgium (18 to 65 years of age) was retained. Daily intake (grams per day) was calculated taking into account frequency and seasonality of consumption, and distributions were obtained that can be used in quantitative risk assessment for chemical hazards with chronic effects on human health. Data also were recalculated to obtain discrete distributions of consumption per portion and the corresponding frequency of consumption, which can be used in acute microbiological risk assessment or outbreak investigations. The ranked median daily consumption of fruits and vegetables was similar in Spain and Belgium: apple > strawberry > grapes > strawberries and raspberries; and tomatoes > leafy greens > bell peppers > fresh herbs. However, vegetable consumption was higher (in terms of both portion and frequency of consumption) in Spain than in Belgium, whereas the opposite was found for fruit consumption. Regarding consumer handling practices related to storage time and method, Belgian consumers less frequently stored their fresh produce in a refrigerator and did so for shorter times compared with Spanish consumers. Washing practices for lettuce heads and packed leafy greens also were different. The survey revealed differences between these two countries in consumption and consumer handling practices, which can have an impact on outcomes of future microbiological or chemical risk assessment studies.

ImageJ: Image processing and analysis in Java

NASA Astrophysics Data System (ADS)

Rasband, W. S.

2012-06-01

ImageJ is a public domain Java image processing program inspired by NIH Image. It can display, edit, analyze, process, save and print 8-bit, 16-bit and 32-bit images. It can read many image formats including TIFF, GIF, JPEG, BMP, DICOM, FITS and "raw". It supports "stacks", a series of images that share a single window. It is multithreaded, so time-consuming operations such as image file reading can be performed in parallel with other operations.

Selecting automation for the clinical chemistry laboratory.

PubMed

Melanson, Stacy E F; Lindeman, Neal I; Jarolim, Petr

2007-07-01

Laboratory automation proposes to improve the quality and efficiency of laboratory operations, and may provide a solution to the quality demands and staff shortages faced by today's clinical laboratories. Several vendors offer automation systems in the United States, with both subtle and obvious differences. Arriving at a decision to automate, and the ensuing evaluation of available products, can be time-consuming and challenging. Although considerable discussion concerning the decision to automate has been published, relatively little attention has been paid to the process of evaluating and selecting automation systems. To outline a process for evaluating and selecting automation systems as a reference for laboratories contemplating laboratory automation. Our Clinical Chemistry Laboratory staff recently evaluated all major laboratory automation systems in the United States, with their respective chemistry and immunochemistry analyzers. Our experience is described and organized according to the selection process, the important considerations in clinical chemistry automation, decisions and implementation, and we give conclusions pertaining to this experience. Including the formation of a committee, workflow analysis, submitting a request for proposal, site visits, and making a final decision, the process of selecting chemistry automation took approximately 14 months. We outline important considerations in automation design, preanalytical processing, analyzer selection, postanalytical storage, and data management. Selecting clinical chemistry laboratory automation is a complex, time-consuming process. Laboratories considering laboratory automation may benefit from the concise overview and narrative and tabular suggestions provided.

Proportional reasoning as a heuristic-based process: time constraint and dual task considerations.

PubMed

Gillard, Ellen; Van Dooren, Wim; Schaeken, Walter; Verschaffel, Lieven

2009-01-01

The present study interprets the overuse of proportional solution methods from a dual process framework. Dual process theories claim that analytic operations involve time-consuming executive processing, whereas heuristic operations are fast and automatic. In two experiments to test whether proportional reasoning is heuristic-based, the participants solved "proportional" problems, for which proportional solution methods provide correct answers, and "nonproportional" problems known to elicit incorrect answers based on the assumption of proportionality. In Experiment 1, the available solution time was restricted. In Experiment 2, the executive resources were burdened with a secondary task. Both manipulations induced an increase in proportional answers and a decrease in correct answers to nonproportional problems. These results support the hypothesis that the choice for proportional methods is heuristic-based.

Towards an automated intelligence product generation capability

NASA Astrophysics Data System (ADS)

Smith, Alison M.; Hawes, Timothy W.; Nolan, James J.

2015-05-01

Creating intelligence information products is a time consuming and difficult process for analysts faced with identifying key pieces of information relevant to a complex set of information requirements. Complicating matters, these key pieces of information exist in multiple modalities scattered across data stores, buried in huge volumes of data. This results in the current predicament analysts find themselves; information retrieval and management consumes huge amounts of time that could be better spent performing analysis. The persistent growth in data accumulation rates will only increase the amount of time spent on these tasks without a significant advance in automated solutions for information product generation. We present a product generation tool, Automated PrOduct Generation and Enrichment (APOGEE), which aims to automate the information product creation process in order to shift the bulk of the analysts' effort from data discovery and management to analysis. APOGEE discovers relevant text, imagery, video, and audio for inclusion in information products using semantic and statistical models of unstructured content. APOGEEs mixed-initiative interface, supported by highly responsive backend mechanisms, allows analysts to dynamically control the product generation process ensuring a maximally relevant result. The combination of these capabilities results in significant reductions in the time it takes analysts to produce information products while helping to increase the overall coverage. Through evaluation with a domain expert, APOGEE has been shown the potential to cut down the time for product generation by 20x. The result is a flexible end-to-end system that can be rapidly deployed in new operational settings.

Putting the ‘patient’ in patient safety: a qualitative study of consumer experiences

PubMed Central

Rathert, Cheryl; Brandt, Julie; Williams, Eric S.

2011-01-01

Abstract Background  Although patient safety has been studied extensively, little research has directly examined patient and family (consumer) perceptions. Evidence suggests that clinicians define safety differently from consumers, e.g. clinicians focus more on outcomes, whereas consumers may focus more on processes. Consumer perceptions of patient safety are important for several reasons. First, health‐care policy leaders have been encouraging patients and families to take a proactive role in ensuring patient safety; therefore, an understanding of how patients define safety is needed. Second, consumer perceptions of safety could influence outcomes such as trust and satisfaction or compliance with treatment protocols. Finally, consumer perspectives could be an additional lens for viewing complex systems and processes for quality improvement efforts. Objectives  To qualitatively explore acute care consumer perceptions of patient safety. Design and methods  Thirty‐nine individuals with a recent overnight hospital visit participated in one of four group interviews. Analysis followed an interpretive analytical approach. Results  Three basic themes were identified: Communication, staffing issues and medication administration. Consumers associated care process problems, such as delays or lack of information, with safety rather than as service quality problems. Participants agreed that patients need family caregivers as advocates. Conclusions  Consumers seem acutely aware of care processes they believe pose risks to safety. Perceptual measures of patient safety and quality may help to identify areas where there are higher risks of preventable adverse events. PMID:21624026

Diagnostics of Dielectric Materials with Several Relaxation Times

NASA Astrophysics Data System (ADS)

Karpov, A. G.; Klemeshev, V. A.

2018-04-01

A set of means for detection and preprocessing of dielectrometric information has been suggested for studying the polarization/depolarization of dielectrics. Special attention has been paid to the processing of dielectrometric data for inhomogeneous materials using dielectric diagrams. Rapid analysis has been carried out the results of which can be used as initial approximations in more accurate (more complicated and time-consuming) iterative algorithms for model fitting.

Service Quality Management Systems: An Annotated Bibliography

DTIC Science & Technology

1992-05-01

customers, Fortune, 122, 38-48. Key words: Consumer preferences , customer expectations Abstract: Rice presents a profile of the 1990 U.S. consumers...business process, 16 competitive advantage, 6, 10 consumer, 5 consumer affairs department, 19 consumer preferences , 30 consumer research, 10,24

Improving the Aircraft Design Process Using Web-Based Modeling and Simulation

NASA Technical Reports Server (NTRS)

Reed, John A.; Follen, Gregory J.; Afjeh, Abdollah A.; Follen, Gregory J. (Technical Monitor)

2000-01-01

Designing and developing new aircraft systems is time-consuming and expensive. Computational simulation is a promising means for reducing design cycle times, but requires a flexible software environment capable of integrating advanced multidisciplinary and multifidelity analysis methods, dynamically managing data across heterogeneous computing platforms, and distributing computationally complex tasks. Web-based simulation, with its emphasis on collaborative composition of simulation models, distributed heterogeneous execution, and dynamic multimedia documentation, has the potential to meet these requirements. This paper outlines the current aircraft design process, highlighting its problems and complexities, and presents our vision of an aircraft design process using Web-based modeling and simulation.

Improving the Aircraft Design Process Using Web-based Modeling and Simulation

NASA Technical Reports Server (NTRS)

Reed, John A.; Follen, Gregory J.; Afjeh, Abdollah A.

2003-01-01

Designing and developing new aircraft systems is time-consuming and expensive. Computational simulation is a promising means for reducing design cycle times, but requires a flexible software environment capable of integrating advanced multidisciplinary and muitifidelity analysis methods, dynamically managing data across heterogeneous computing platforms, and distributing computationally complex tasks. Web-based simulation, with its emphasis on collaborative composition of simulation models, distributed heterogeneous execution, and dynamic multimedia documentation, has the potential to meet these requirements. This paper outlines the current aircraft design process, highlighting its problems and complexities, and presents our vision of an aircraft design process using Web-based modeling and simulation.

Consumables data base workbook: Formulation of consumables management models

NASA Technical Reports Server (NTRS)

Zamora, M. A.

1977-01-01

Activity consumables data specifications and data applications are presented. The data are structured in a series of "Consumable Data Worksheets" for each activity that includes a profile of its operations and the rate of each consumable required to support the given activity. The data worksheets provide for the uniform specification of consumables data, allows for the ready identification of the consumables affected by a given activity, and facilitates the updating process. An activity is defined and the data that must be included in the data worksheets are specified. An example of its use and application is given, i.e. consumables data requirements for the performance of the EVA. The consumables data for the activities currently identified for the shuttle spacecraft are included. The consumables data sources are identified and information to facilitate the maintenance process is detailed.

ENVIRONMENTAL RISK ASSESSMENT/COMMUNICATION TOOLS FOR REVITALIZATION OF POTENTIALLY CONTAMINATED SITES CD

EPA Science Inventory

Revitalization of potentially contaminated sites is often at a disadvantage compared to greenfield development. Apart from the lower cost of land in rural areas, redevelopment is very often still seen as a rather complex time- and cost-consuming process. Additionally, the potenti...

Fluorous Compounds and their Role in Separation Chemistry

ERIC Educational Resources Information Center

Ubeda, Maria Angeles; Dembinski, Roman

2006-01-01

The main focus of fluorous chemistry targets resource and time-consuming separation, in order to improve the material economy and thus represents potentially environmentally friendly technology. Fluorous chemistry offers the advantage of easy separation based on different affirmatives of organics and fluorous molecules, where the process called…

Modeling fuel succession

Treesearch

Brett Davis; Jan van Wagtendonk; Jen Beck; Kent van Wagtendonk

2009-01-01

Surface fuels data are of critical importance for supporting fire incident management, risk assessment, and fuel management planning, but the development of surface fuels data can be expensive and time consuming. The data development process is extensive, generally beginning with acquisition of remotely sensed spatial data such as aerial photography or satellite...

What We've Learned about Assessing Hands-On Science.

ERIC Educational Resources Information Center

Shavelson, Richard J.; Baxter, Gail P.

1992-01-01

A recent study compared hands-on scientific inquiry assessment to assessments involving lab notebooks, computer simulations, short-answer paper-and-pencil problems, and multiple-choice questions. Creating high quality performance assessments is a costly, time-consuming process requiring considerable scientific and technological know-how. Improved…

Organizational culture, climate and person-environment fit: Relationships with employment outcomes for mental health consumers.

PubMed

Kirsh, Bonnie

2000-01-01

Although the effects of organizational culture, climate and person-environment fit have been widely studied in the general population, little research exists in this area regarding consumers of mental health services. This research focuses on organizational culture, climate and person-environment fit and their relationship to employment outcomes for mental health consumers. It also examines specific components of organizational culture which are both desired and perceived by mental health consumers. Thirty-six (N=36) consumers were recruited into one of two groups: individuals who were employed at the time of the study and those who had recently left their jobs. Instruments used were the Workplace Climate Questionnaire (WCQ) and the Organizational Culture Profile (OCP). Significant differences were found between groups along the dimensions of organizational culture/climate and person-environment fit. Although few differences were found between groups with regards to desired workplace characteristics, many differences in perceived characteristics were found. The findings point to the importance of assessing the organizational culture/climate and its congruence with individuals' value systems as part of the work integration process.

Strategic questions for consumer-based health communications.

PubMed Central

Sutton, S M; Balch, G I; Lefebvre, R C

1995-01-01

Using the consumer-oriented approach of social and commercial marketers, this article presents a process for crafting messages designed to improve people's health behaviors. The process, termed consumer-based health communications (CHC), transforms scientific recommendations into message strategies that are relevant to the consumer. The core of CHC is consumer research conducted to understand the consumer's reality, and thereby allowing six strategic questions to be answered. The immediate result of the CHC process is a strategy statement--a few pages that lay out who the target consumer is, what action should be taken, what to promise and how to make the promise credible, how and when to reach him or her, and what image to convey. The strategy statement then guides the execution of all communication efforts, be they public relations, mass media, direct marketing, media advocacy, or interpersonal influence. It identifies the most important "levers" for contact with the consumer. Everyone from creative specialists through management and program personnel can use the strategy statement as a touchstone to guide and judge the effectiveness of their efforts. The article provides a step by step illustration of the CHC process using the 5 A Day campaign as an example. PMID:8570827

Strategic questions for consumer-based health communications.

PubMed

Sutton, S M; Balch, G I; Lefebvre, R C

1995-01-01

Using the consumer-oriented approach of social and commercial marketers, this article presents a process for crafting messages designed to improve people's health behaviors. The process, termed consumer-based health communications (CHC), transforms scientific recommendations into message strategies that are relevant to the consumer. The core of CHC is consumer research conducted to understand the consumer's reality, and thereby allowing six strategic questions to be answered. The immediate result of the CHC process is a strategy statement--a few pages that lay out who the target consumer is, what action should be taken, what to promise and how to make the promise credible, how and when to reach him or her, and what image to convey. The strategy statement then guides the execution of all communication efforts, be they public relations, mass media, direct marketing, media advocacy, or interpersonal influence. It identifies the most important "levers" for contact with the consumer. Everyone from creative specialists through management and program personnel can use the strategy statement as a touchstone to guide and judge the effectiveness of their efforts. The article provides a step by step illustration of the CHC process using the 5 A Day campaign as an example.

How Social Ties Influence Consumer: Evidence from Event-Related Potentials.

PubMed

Luan, Jing; Yao, Zhong; Bai, Yan

2017-01-01

A considerable amount of marketing research has reported that consumers are more saliently influenced by friends (strong social ties) than by acquaintances and strangers (weak social ties). To shed light on the neural and psychological processes underlying such phenomenon, in this study we designed an amended S1-S2 paradigm (product-[reviewer-review]) that is based on realistic consumer purchase experiences. After incoming all given information (product, reviewer, review), participants were required to state their purchase intentions. The neurocognitive and emotional processes related to friend and stranger stimuli were delineated to suggest how social ties influence consumers during their shopping processes. Larger P2 (fronto-central scalp areas) and P3 (central and posterior-parietal scalp areas) components under stranger condition were elicited successfully. These findings demonstrate that the cognitive and emotional processing of friend and stranger stimuli occurs at stages of neural activity, and can be indicated by the P2 and P3 components. Electrophysiological data also support the hypothesis that different neural and emotional processing magnitude and strength underlie friend and stranger effect in the context of consumer purchase. During this process, the perception of stimuli evoked P2, subsequently emotional processing and attention modulation were activated and indicated by P2 and P3. The friend dominated phenomenon can be interpreted as the result of distinctive neurocognitive and emotional processing magnitude, which suggests that psychological and emotional factors can guide consumer decision making. This study consolidates that event related potential (ERP) methodology is likely to be a more sensitive method for investigating consumer behaviors. From the perspectives of management and marketing, our findings show that the P2 and P3 components can be employed as an indicator to probe the influential factors of consumer purchase intentions.

How Social Ties Influence Consumer: Evidence from Event-Related Potentials

PubMed Central

Yao, Zhong

2017-01-01

A considerable amount of marketing research has reported that consumers are more saliently influenced by friends (strong social ties) than by acquaintances and strangers (weak social ties). To shed light on the neural and psychological processes underlying such phenomenon, in this study we designed an amended S1-S2 paradigm (product-[reviewer-review]) that is based on realistic consumer purchase experiences. After incoming all given information (product, reviewer, review), participants were required to state their purchase intentions. The neurocognitive and emotional processes related to friend and stranger stimuli were delineated to suggest how social ties influence consumers during their shopping processes. Larger P2 (fronto-central scalp areas) and P3 (central and posterior-parietal scalp areas) components under stranger condition were elicited successfully. These findings demonstrate that the cognitive and emotional processing of friend and stranger stimuli occurs at stages of neural activity, and can be indicated by the P2 and P3 components. Electrophysiological data also support the hypothesis that different neural and emotional processing magnitude and strength underlie friend and stranger effect in the context of consumer purchase. During this process, the perception of stimuli evoked P2, subsequently emotional processing and attention modulation were activated and indicated by P2 and P3. The friend dominated phenomenon can be interpreted as the result of distinctive neurocognitive and emotional processing magnitude, which suggests that psychological and emotional factors can guide consumer decision making. This study consolidates that event related potential (ERP) methodology is likely to be a more sensitive method for investigating consumer behaviors. From the perspectives of management and marketing, our findings show that the P2 and P3 components can be employed as an indicator to probe the influential factors of consumer purchase intentions. PMID:28081196

Natural antioxidant activity of commonly consumed plant foods in India: effect of domestic processing.

PubMed

Sreeramulu, D; Reddy, C V K; Chauhan, Anitha; Balakrishna, N; Raghunath, M

2013-01-01

Phytochemicals protect against oxidative stress which in turn helps in maintaining the balance between oxidants and antioxidants. In recent times natural antioxidants are gaining considerable interest among nutritionists, food manufacturers, and consumers because of their perceived safety, potential therapeutic value, and long shelf life. Plant foods are known to protect against degenerative diseases and ageing due to their antioxidant activity (AOA) attributed to their high polyphenolic content (PC). Data on AOA and PC of Indian plant foods is scanty. Therefore we have determined the antioxidant activity in 107 commonly consumed Indian plant foods and assessed their relation to their PC. Antioxidant activity is presented as the range of values for each of the food groups. The foods studied had good amounts of PC and AOA although they belonged to different food groups. Interestingly, significant correlation was observed between AOA (DPPH and FRAP) and PC in most of the foods, corroborating the literature that polyphenols are potent antioxidants and that they may be important contributors to the AOA of the plant foods. We have also observed that common domestic methods of processing may not affect the PC and AOA of the foods studied in general. To the best of our knowledge, these are the first results of the kind in commonly consumed Indian plant foods.

Reference Pricing Changes The 'Choice Architecture' Of Health Care For Consumers.

PubMed

Robinson, James C; Brown, Timothy T; Whaley, Christopher

2017-03-01

Reference pricing in health insurance creates incentives for patients to select for nonemergency services providers that charge relatively low prices and still offer high quality of care. It changes the "choice architecture" by offering standard coverage if the patient chooses cost-effective providers but requires considerable consumer cost sharing if more expensive alternatives are selected. The short-term impact of reference pricing has been to shift patient volumes from hospital-based to freestanding surgical, diagnostic, imaging, and laboratory facilities. This article summarizes reference pricing's impacts to date on patient choice, provider prices, surgical complications, and employer spending and estimates its potential impacts if expanded to more services and a broader population. Reference pricing induces consumers to select lower-price alternatives for all of the forms of care studied, leading to significant reductions in prices paid and spending incurred by insurers and employers. The impact on consumer cost sharing is mixed, with some studies finding higher copayments and some lower. We conclude with a discussion of the incentives created for providers to redesign their clinical processes and for efficient providers to expand into price-sensitive markets. Over time, reference pricing may increase pressures for price competition and lead to further cost-reducing innovations in health care products and processes. Project HOPE—The People-to-People Health Foundation, Inc.

The impact of coercion on services from the perspective of mental health care consumers with co-occurring disorders.

PubMed

Stanhope, Victoria; Marcus, Steven; Solomon, Phyllis

2009-02-01

Disengagement from services by people with serious mental illnesses continues to be a major challenge for the mental health system. Assertive community treatment combined with Housing First services is an intervention targeted toward consumers whom the system has failed to engage. The processes involved in engaging and maintaining consumers in mental health services play an important role but remain an understudied aspect of the intervention. This study examined the social interaction between consumers and case managers from the perspective of consumers. Seventy service contacts between unique consumer-case manager dyads were sampled. Consumers with co-occurring serious mental illness and substance use disorders completed interviews after each service contact. They provided information on sociodemographic characteristics, service contact characteristics, consumer-provider relationship, utilization of coercive strategies, perceived coercion, and service contact evaluation. Multivariate regression analyses examined the association of consumer-provider relationship and perceived coercion with service contact evaluation. Consumer-provider relationship was negatively associated with perceived coercion (effect size=.08). Perceived coercion was negatively associated with service contact evaluation (effect size=.34). Perceived coercion was positively associated with time in the program (effect size=.17) and negatively associated with length of the service contact (effect size=.14). Effect sizes ranging from .08 to .34 are typically considered small to medium. Findings demonstrate that for consumers, a positive response to service contacts indicated that they did not feel coerced. With consumers whose connection to services is tenuous, an immediate positive response to service contacts may be vital to maintain engagement. Research is needed to identify supportive case manager strategies that facilitate relationship building.

Analysis of production flow process with lean manufacturing approach

NASA Astrophysics Data System (ADS)

Siregar, Ikhsan; Arif Nasution, Abdillah; Prasetio, Aji; Fadillah, Kharis

2017-09-01

This research was conducted on the company engaged in the production of Fast Moving Consumer Goods (FMCG). The production process in the company are still exists several activities that cause waste. Non value added activity (NVA) in the implementation is still widely found, so the cycle time generated to make the product will be longer. A form of improvement on the production line is by applying lean manufacturing method to identify waste along the value stream to find non value added activities. Non value added activity can be eliminated and reduced by utilizing value stream mapping and identifying it with activity mapping process. According to the results obtained that there are 26% of value-added activities and 74% non value added activity. The results obtained through the current state map of the production process of process lead time value of 678.11 minutes and processing time of 173.94 minutes. While the results obtained from the research proposal is the percentage of value added time of 41% of production process activities while non value added time of the production process of 59%. While the results obtained through the future state map of the production process of process lead time value of 426.69 minutes and processing time of 173.89 minutes.

Autocorrelated process control: Geometric Brownian Motion approach versus Box-Jenkins approach

NASA Astrophysics Data System (ADS)

Salleh, R. M.; Zawawi, N. I.; Gan, Z. F.; Nor, M. E.

2018-04-01

Existing of autocorrelation will bring a significant effect on the performance and accuracy of process control if the problem does not handle carefully. When dealing with autocorrelated process, Box-Jenkins method will be preferred because of the popularity. However, the computation of Box-Jenkins method is too complicated and challenging which cause of time-consuming. Therefore, an alternative method which known as Geometric Brownian Motion (GBM) is introduced to monitor the autocorrelated process. One real case of furnace temperature data is conducted to compare the performance of Box-Jenkins and GBM methods in monitoring autocorrelation process. Both methods give the same results in terms of model accuracy and monitoring process control. Yet, GBM is superior compared to Box-Jenkins method due to its simplicity and practically with shorter computational time.

A web-based tree crown condition training and evaluation tool for urban and community forestry

Treesearch

Matthew F. Winn; Neil A. Clark; Philip A. Araman; Sang-Mook Lee

2007-01-01

Training personnel for natural resource related field work can be a costly and time-consuming process. For that reason, web-based training is considered by many to be a more attractive alternative to on-site training. The U.S. Forest Service Southern Research Station unit with Virginia Tech cooperators in Blacksburg, Va., are in the process of constructing a web site...

Testing for context-dependence in a processing chain interaction among detritus-feeding aquatic insects

PubMed Central

DAUGHERTY, MATTHEW P.; JULIANO, STEVEN A.

2008-01-01

Scirtid beetles may benefit mosquitoes Ochlerotatus triseriatus (Say) by consuming whole leaves and leaving behind fine particles required by mosquito larvae. Such interactions based on the sequential use of a resource that occurs in multiple forms are known as processing chains.Models of processing chains predict that interactions can vary from commensal (0, +) to amensal (0, −), depending on how quickly resource is processed in the absence of consumers.The scirtid-O. triseriatus system was used to test the prediction derived from processing chain models that, as consumer-independent processing increases, scirtids benefit mosquitoes less. Consumer-independent processing rate was manipulated by using different leaf species that vary in decay rate, or by physically crushing a single leaf type to different degrees.Although scirtids increased the production of fine particles, the effects of scirtids on mosquitoes were weak and were not dependent on consumer-independent processing rate.In the leaf manipulation experiment, a correlation between scirtid feeding and consumer-independent processing was detected. Numerical simulations suggest that such a correlation may eliminate shifts from commensal to amensal at equilibrium; because mosquito populations are typically not at equilibrium, however, this correlation may not be important.There was evidence that mosquitoes affected scirtids negatively, which is inconsistent with the structure of processing chain interactions in models. Processing chain models need to incorporate more detail on the biology of scirtids and O. triseriatus, especially alternative mechanisms of interaction, if they are to describe scirtid-O. triseriatus dynamics accurately. PMID:19060960

Economy with the time delay of information flow—The stock market case

NASA Astrophysics Data System (ADS)

Miśkiewicz, Janusz

2012-02-01

Any decision process requires information about the past and present state of the system, but in an economy acquiring data and processing it is an expensive and time-consuming task. Therefore, the state of the system is often measured over some legal interval, analysed after the end of well defined time periods and the results announced much later before any strategic decision is envisaged. The various time delay roles have to be crucially examined. Here, a model of stock market coupled with an economy is investigated to emphasise the role of the time delay span on the information flow. It is shown that the larger the time delay the more important the collective behaviour of agents since one observes time oscillations in the absolute log-return autocorrelations.

Substrate-Limited Saccharomyces cerevisiae Yeast Strains Allow Control of Fermentation during Bread Making.

PubMed

Struyf, Nore; Laurent, Jitka; Verspreet, Joran; Verstrepen, Kevin J; Courtin, Christophe M

2017-04-26

Identification and use of yeast strains that are unable to consume one or more otherwise fermentable substrate types could allow a more controlled fermentation process with more flexibility regarding fermentation times. In this study, Saccharomyces cerevisiae strains with different capacities to consume substrates present in wheat were selected to investigate the impact of substrate limitation on dough fermentation and final bread volume. Results show that fermentation of dough with maltose-negative strains relies on the presence of fructan and sucrose as fermentable substrates and can be used for regular bread making. Levels of fructan and sucrose, endogenously present or added, hence determine the extent of fermentation and timing at the proofing stage. Whole meal is inherently more suitable for substrate-limited fermentation than white flour due to the presence of higher native levels of these substrates. Bread making protocols with long fermentation times are accommodated by addition of substrates such as sucrose.

The association between red and processed meat consumption and iron intakes and status among British adults.

PubMed

Gibson, Sigrid; Ashwell, Margaret

2003-06-01

To examine the association between consumption of red and processed meat (RPM) and iron intakes and status in adults. Further analysis of the Dietary and Nutritional Survey of British Adults, a cross-sectional study of 2197 adults aged 16-64 years carried out in 1986/7. Adults (836 men and 838 women) with serum ferritin measurements, who were not taking iron supplements, were classified into four groups according to RPM consumption (from 7-day weighed records). Iron absorbed was estimated from equations based on haem and non-haem iron and the influence of iron stores. Women who ate least meat (<90 g day-1) had three times the risk of a low iron intake (below the Lower Reference Nutrient Intake) compared with high consumers of RPM (>140 g day-1). Men who ate no RPM also had a higher risk of low iron intake. Using an estimate of minimal values for iron losses, there was a twofold difference in the potential risk of negative iron balance between women non-RPM consumers and high RPM consumers. Status measurements indicated that, among women, anaemia was least prevalent (6%) among high consumers compared with 12-14% among average RPM consumers. Inverse trends were also observed for serum ferritin in both sexes. Low consumption of RPM has implications for iron intakes and iron status in men and women, since the risk of negative iron balance and its consequences are increased. Dietary messages must consider these implications and provide appropriate advice.

Automatic segmentation of coronary arteries from computed tomography angiography data cloud using optimal thresholding

NASA Astrophysics Data System (ADS)

Ansari, Muhammad Ahsan; Zai, Sammer; Moon, Young Shik

2017-01-01

Manual analysis of the bulk data generated by computed tomography angiography (CTA) is time consuming, and interpretation of such data requires previous knowledge and expertise of the radiologist. Therefore, an automatic method that can isolate the coronary arteries from a given CTA dataset is required. We present an automatic yet effective segmentation method to delineate the coronary arteries from a three-dimensional CTA data cloud. Instead of a region growing process, which is usually time consuming and prone to leakages, the method is based on the optimal thresholding, which is applied globally on the Hessian-based vesselness measure in a localized way (slice by slice) to track the coronaries carefully to their distal ends. Moreover, to make the process automatic, we detect the aorta using the Hough transform technique. The proposed segmentation method is independent of the starting point to initiate its process and is fast in the sense that coronary arteries are obtained without any preprocessing or postprocessing steps. We used 12 real clinical datasets to show the efficiency and accuracy of the presented method. Experimental results reveal that the proposed method achieves 95% average accuracy.

Open-source hardware is a low-cost alternative for scientific instrumentation and research

USDA-ARS?s Scientific Manuscript database

Scientific research requires the collection of data in order to study, monitor, analyze, describe, or understand a particular process or event. Data collection efforts are often a compromise: manual measurements can be time-consuming and labor-intensive, resulting in data being collected at a low f...

The Domains for the Multi-Criteria Decisions about E-Learning Systems

ERIC Educational Resources Information Center

Uysal, Murat Pasa

2012-01-01

Developments in computer and information technologies continue to give opportunities for designing advanced E-learning systems while entailing objective and technical evaluation methodologies. Design and development of E-learning systems require time-consuming and labor-intensive processes; therefore any decision about these systems and their…

77 FR 39112 - State Official Notification Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... BUREAU OF CONSUMER FINANCIAL PROTECTION 12 CFR Part 1082 [Docket No. CFPB-2011-0005] RIN 3170-AA02... the SUPPLEMENTARY INFORMATION. V. Section-by-Section Summary Section 1082.1(a) Notice Requirement Section 1082.1(a) of the Interim Final Rule sets out the timing and process for notice by State Officials...

Use of Anthropogenic Radioisotopes to Estimate Rates of Soil Redistribution by Wind

USDA-ARS?s Scientific Manuscript database

Wind erosion results in soil degradation and fugitive dust emissions. The temporal and spatial variability of aeolian processes makes local estimates of long-term average erosion costly and time consuming. Atmospheric testing of nuclear weapons during the 1950s and 1960s resulted in previously non...

Predicting Stored Grain Insect Population Densities Using an Electronic Probe Trap

USDA-ARS?s Scientific Manuscript database

Manual sampling of insects in stored grain is a laborious and time consuming process. Automation of grain sampling should help to increase the adoption of stored-grain integrated pest management. A new commercial electronic grain probe trap (OPI Insector™) has recently been marketed. We field tested...

Oral Anatomy Laboratory Examinations in a Physical Therapy Program

ERIC Educational Resources Information Center

Fabrizio, Philip A.

2013-01-01

The process of creating and administering traditional tagged anatomy laboratory examinations is time consuming for instructors and limits laboratory access for students. Depending on class size and the number of class, sections, creating, administering, and breaking down a tagged laboratory examination may involve one to two eight-hour days.…

A Guide to Intellectual Property Protection, Third Edition.

ERIC Educational Resources Information Center

Minnesota Small Business Assistance Office, St. Paul.

Protecting an idea is often a difficult process. Some ideas and inventions cannot be protected, while others are eligible for only narrow or partial immunity from potential competition and imitation. Obtaining even minimal protection can often be expensive, time consuming, and ultimately result in uncertain or even negative benefits to the…

Field testing a mobile inelastic neutron scattering system to measure soil carbon

USDA-ARS?s Scientific Manuscript database

Cropping history in conjunction with soil management practices can have a major impact on the amount of organic carbon (C) stored in soil. Current methods of assessing soil C based on soil coring and subsequent processing procedures prior to laboratory analysis are labor intensive and time consuming...

Feature selection methods for object-based classification of sub-decimeter resolution digital aerial imagery

USDA-ARS?s Scientific Manuscript database

Due to the availability of numerous spectral, spatial, and contextual features, the determination of optimal features and class separabilities can be a time consuming process in object-based image analysis (OBIA). While several feature selection methods have been developed to assist OBIA, a robust c...

Computer Controlled Optical Surfacing With Orbital Tool Motion

NASA Astrophysics Data System (ADS)

Jones, Robert A.

1985-11-01

Asymmetric aspheric optical surfaces are very difficult to fabricate using classical techniques and laps the same size as the workpiece. Opticians can produce such surfaces by hand grinding and polishing, using small laps with orbital tool motion. However, this is a time consuming process unsuitable for large optical elements.

From Gutenberg to Gates: Media Matters

ERIC Educational Resources Information Center

Considine, David M.

2009-01-01

Media consolidation and convergence have increasingly changed the way individuals as both consumers and citizens access, process, and communicate information at the local, national, and global levels. Media industries and institutions influence public perception and occupy our time at work and at home more and more. Media literacy has become…

Research Trends with Cross Tabulation Search Engine

ERIC Educational Resources Information Center

Yin, Chengjiu; Hirokawa, Sachio; Yau, Jane Yin-Kim; Hashimoto, Kiyota; Tabata, Yoshiyuki; Nakatoh, Tetsuya

2013-01-01

To help researchers in building a knowledge foundation of their research fields which could be a time-consuming process, the authors have developed a Cross Tabulation Search Engine (CTSE). Its purpose is to assist researchers in 1) conducting research surveys, 2) efficiently and effectively retrieving information (such as important researchers,…

Sea Stories: A Collaborative Tool for Articulating Tactical Knowledge.

ERIC Educational Resources Information Center

Radtke, Paul H.; Frey, Paul R.

Having subject matter experts (SMEs) identify the skills and knowledge to be taught is among the more difficult and time-consuming steps in the training development process. A procedure has been developed for identifying specific tactical decision-making knowledge requirements and translating SME knowledge into appropriate multimedia…

Consumers' conceptualization of ultra-processed foods.

PubMed

Ares, Gastón; Vidal, Leticia; Allegue, Gimena; Giménez, Ana; Bandeira, Elisa; Moratorio, Ximena; Molina, Verónika; Curutchet, María Rosa

2016-10-01

Consumption of ultra-processed foods has been associated with low diet quality, obesity and other non-communicable diseases. This situation makes it necessary to develop educational campaigns to discourage consumers from substituting meals based on unprocessed or minimally processed foods by ultra-processed foods. In this context, the aim of the present work was to investigate how consumers conceptualize the term ultra-processed foods and to evaluate if the foods they perceive as ultra-processed are in concordance with the products included in the NOVA classification system. An online study was carried out with 2381 participants. They were asked to explain what they understood by ultra-processed foods and to list foods that can be considered ultra-processed. Responses were analysed using inductive coding. The great majority of the participants was able to provide an explanation of what ultra-processed foods are, which was similar to the definition described in the literature. Most of the participants described ultra-processed foods as highly processed products that usually contain additives and other artificial ingredients, stressing that they have low nutritional quality and are unhealthful. The most relevant products for consumers' conceptualization of the term were in agreement with the NOVA classification system and included processed meats, soft drinks, snacks, burgers, powdered and packaged soups and noodles. However, some of the participants perceived processed foods, culinary ingredients and even some minimally processed foods as ultra-processed. This suggests that in order to accurately convey their message, educational campaigns aimed at discouraging consumers from consuming ultra-processed foods should include a clear definition of the term and describe some of their specific characteristics, such as the type of ingredients included in their formulation and their nutritional composition. Copyright © 2016 Elsevier Ltd. All rights reserved.

Compounds of parasitic roundworm absorbing in the visible region: target molecules for detection of roundworm in Atlantic cod.

PubMed

Stormo, Svein K; Ernstsen, Arild; Nilsen, Heidi; Heia, Karsten; Sivertsen, Agnar H; Elvevoll, Edel

2004-07-01

The objective of this study was to contribute to the development of technology that will be able to replace manual operations in processing of fish fillets. Removal of parasites, black lining, remnants of skin, and bloodstains are costly and time-consuming operations to the fish processing industry. The presence of parasites in fish products tends to spoil consumers' appetites. Recent reports questioning the safety of eating cod infected with parasites might lower consumer acceptance of seafood. Presently, parasites are detected and removed manually. An average efficiency of about 75% under commercial conditions has been reported. In this study, we focused on biochemical differences between cod muscle and the prevalent anisakine nematode species (Anisakis simplex and Pseudoterranova decipiens) infecting Atlantic cod (Gadus morhua). Using reversed phase high-performance liquid chromatography equipped with a photodiode array detector, substances absorbing in the range 300 to 600 nm were identified in extracts from parasite material. These substances were not detected in extracts from cod tissue. Significant biochemical differences between cod muscle and parasite material have thus been demonstrated.

Cognitive load, stress, and disinhibited eating.

PubMed

Lattimore, Paul; Maxwell, Linda

2004-11-01

The impact of cognitive distraction on eating behaviour was examined in restrained and unrestrained eaters. It was predicted that restrained eaters would eat more than unrestrained eaters following high cognitive load when it involves processing of ego-threat information independent of self-reported anxiety. There were 119 female participants randomly allocated to one of four experimental conditions whereby cognitive load and ego threat were manipulated using modified colour-naming Stroop (CNS) tasks. Anxiety ratings were made prior to and following experimental tasks. After performing Stroop tasks, participants consumed snack foods ad libitum. Restrained eaters consumed significantly more food when high cognitive load was ego threatening than when it involved processing and memorisation of colour nouns and consumed significantly more than unrestrained eaters in a high cognitive load ego-threat condition. Posttask anxiety was greater than baseline across all conditions. Task difficulty was greater under high cognitive load than low cognitive load as indicated by Stroop response times. These results indicated that the escape theory of disinhibited eating is conceptually subsumed by a more generalisable limited cognitive capacity model.

Research on the Influence of Perceived Risk in Consumer On-line Purchasing Decision

NASA Astrophysics Data System (ADS)

Hong, Zhao; Yi, Li

Perceived risk is an important factor that affects consumer's on-line shopping purchasing decision, through the perceived theories the consumer can know clearly which step owns higher risk in the whole shopping process, then learn how to prevent it, this process also strengthen the consumer confidence, thus lowering to know that the risk adjudicate to the feeling, so the essay has important and realistic meaning for further expand the electronic commerce. At first, investigate, collect, tidy up, analyze the questionnaire information, and thus get the primary data. Finally try to find out the influence of perceived risk to each stage of purchasing decision during consumer on-line shopping process with data and personal analytical. The paper is a complement to the local and existing perceived theories. The result of the study manifests that, the order of main perceived risks which felt by consumer during on-line shopping process are as follow: financial risk, the performance risk and service risk.

Refrigerated fruit juices: quality and safety issues.

PubMed

Esteve, Maria Jose; Frígola, Ana

2007-01-01

Fruit juices are an important source of bioactive compounds, but techniques used for their processing and subsequent storage may cause alterations in their contents so they do not provide the benefits expected by the consumer. In recent years consumers have increasingly sought so-called "fresh" products (like fresh products), stored in refrigeration. This has led the food industry to develop alternative processing technologies to produce foods with a minimum of nutritional, physicochemical, or organoleptic changes induced by the technologies themselves. Attention has also focused on evaluating the microbiological or toxicological risks that may be involved in applying these processes, and their effect on food safety, in order to obtain safe products that do not present health risks. This concept of minimal processing is currently becoming a reality with conventional technologies (mild pasteurization) and nonthermal technologies, some recently introduced (pasteurization by high hydrostatic pressure) and some perhaps with a more important role in the future (pulsed electric fields). Nevertheless, processing is not the only factor that affects the quality of these products. It is also necessary to consider the conditions for refrigerated storage and to control time and temperature.

Towards Implementation of a Generalized Architecture for High-Level Quantum Programming Language

NASA Astrophysics Data System (ADS)

Ameen, El-Mahdy M.; Ali, Hesham A.; Salem, Mofreh M.; Badawy, Mahmoud

2017-08-01

This paper investigates a novel architecture to the problem of quantum computer programming. A generalized architecture for a high-level quantum programming language has been proposed. Therefore, the programming evolution from the complicated quantum-based programming to the high-level quantum independent programming will be achieved. The proposed architecture receives the high-level source code and, automatically transforms it into the equivalent quantum representation. This architecture involves two layers which are the programmer layer and the compilation layer. These layers have been implemented in the state of the art of three main stages; pre-classification, classification, and post-classification stages respectively. The basic building block of each stage has been divided into subsequent phases. Each phase has been implemented to perform the required transformations from one representation to another. A verification process was exposed using a case study to investigate the ability of the compiler to perform all transformation processes. Experimental results showed that the efficacy of the proposed compiler achieves a correspondence correlation coefficient about R ≈ 1 between outputs and the targets. Also, an obvious achievement has been utilized with respect to the consumed time in the optimization process compared to other techniques. In the online optimization process, the consumed time has increased exponentially against the amount of accuracy needed. However, in the proposed offline optimization process has increased gradually.

The psychology of nutrition messages.

PubMed

Schofield, Heather; Mullainathan, Sendhil

2008-01-01

The purpose of this paper is to explore consumer thinking about nutrition decisions and how firms can use consumers' awareness of the links between nutrients and health generated by public health messages to market products, including ones, which have little nutritional value. We approach this issue by tracking the development of public health messages based on scientific research, dissemination of those messages in the popular press, and use of nutrition claims in food advertisements to assess whether firms are timing the use of nutrition claims to take advantage of heuristic-based decision-making. Our findings suggest that the timing of the development of nutrition information, its dissemination in the press, and use in advertising accords well with a heuristic processing model in which firms take advantage of associations between nutrient information and health in their advertisements. However, the demonstrated relationships may not be causal. Further research will be needed to provide stronger and more comprehensive evidence regarding the proposed message hijacking process. If the message hijacking framework is borne out: (1) simple overall health rating scales could significantly improve consumer decision-making, (2) the impact of misleading advertisements could be mitigated by encouraging a multidimensional view of nutrition, and (3) more intensive regulation of product labeling could limit the impact of hijacked messages. Overall, this paper considers a novel hypothesis about the impact of public health messages on nutrition and health.

The dynamics of consumer behaviour. On habit, discontent, and other fish to fry.

PubMed

Scholderer, Joachim; Trondsen, Torbjørn

2008-11-01

Recent research has drawn attention to the role of past behaviour and habit in the overall structure of consumer behaviour. We argue that in cross-sectional data past behaviour and habit must be confounded with present beliefs and attitudes when the behaviour in question has been enacted numerous times before. To disentangle the effects, longitudinal data were collected from a large panel of Norwegian consumers (effective N=4184) in 1996, 2000, and 2004. Cross-lagged panel analysis indicated that higher consumption of traditional seafood led to increasingly negative evaluations of the product supply. These negative evaluations, in turn, prompted substitution of traditional seafood with newly available, processed seafood products and an increasing dominance of aqua-cultured species. The theoretical discussion focuses on the inability of static models of consumer behaviour (in particular, the theory of planned behaviour) to capture such dynamic effects. Marketing and policy implications related to the changing structure of the seafood market are outlined.

Context-Sensitive Spelling Correction of Consumer-Generated Content on Health Care

PubMed Central

Chen, Rudan; Zhao, Xianyang; Xu, Wei; Cheng, Wenqing; Lin, Simon

2015-01-01

Background Consumer-generated content, such as postings on social media websites, can serve as an ideal source of information for studying health care from a consumer’s perspective. However, consumer-generated content on health care topics often contains spelling errors, which, if not corrected, will be obstacles for downstream computer-based text analysis. Objective In this study, we proposed a framework with a spelling correction system designed for consumer-generated content and a novel ontology-based evaluation system which was used to efficiently assess the correction quality. Additionally, we emphasized the importance of context sensitivity in the correction process, and demonstrated why correction methods designed for electronic medical records (EMRs) failed to perform well with consumer-generated content. Methods First, we developed our spelling correction system based on Google Spell Checker. The system processed postings acquired from MedHelp, a biomedical bulletin board system (BBS), and saved misspelled words (eg, sertaline) and corresponding corrected words (eg, sertraline) into two separate sets. Second, to reduce the number of words needing manual examination in the evaluation process, we respectively matched the words in the two sets with terms in two biomedical ontologies: RxNorm and Systematized Nomenclature of Medicine -- Clinical Terms (SNOMED CT). The ratio of words which could be matched and appropriately corrected was used to evaluate the correction system’s overall performance. Third, we categorized the misspelled words according to the types of spelling errors. Finally, we calculated the ratio of abbreviations in the postings, which remarkably differed between EMRs and consumer-generated content and could largely influence the overall performance of spelling checkers. Results An uncorrected word and the corresponding corrected word was called a spelling pair, and the two words in the spelling pair were its members. In our study, there were 271 spelling pairs detected, among which 58 (21.4%) pairs had one or two members matched in the selected ontologies. The ratio of appropriate correction in the 271 overall spelling errors was 85.2% (231/271). The ratio of that in the 58 spelling pairs was 86% (50/58), close to the overall ratio. We also found that linguistic errors took up 31.4% (85/271) of all errors detected, and only 0.98% (210/21,358) of words in the postings were abbreviations, which was much lower than the ratio in the EMRs (33.6%). Conclusions We conclude that our system can accurately correct spelling errors in consumer-generated content. Context sensitivity is indispensable in the correction process. Additionally, it can be confirmed that consumer-generated content differs from EMRs in that consumers seldom use abbreviations. Also, the evaluation method, taking advantage of biomedical ontology, can effectively estimate the accuracy of the correction system and reduce manual examination time. PMID:26232246

Attitudes of nursing students on consumer participation: the effectiveness of the Mental Health Consumer Participation Questionnaire.

PubMed

Byrne, Louise; Happell, Brenda; Platania-Phung, Chris

2015-01-01

The aims of this article were to evaluate the Mental Health Consumer Participation Questionnaire, and measure nursing students' attitudes to consumer participation. Undergraduate nursing students (n = 116) completed the Mental Health Consumer Participation Questionnaire at the start of a course on recovery for mental health nursing practice. The current findings confirm an endorsement of consumer participation in individual care processes, but less agreement with participation in organizational-level processes, such as management of mental health services and education of providers. This article also confirms that the questionnaire can effectively measure attitudes to consumer participation. The participation of consumers is critical for achieving person-centered services mental health services. It is important that nursing education influence positive attitudes. © 2014 Wiley Periodicals, Inc.

Missing the Mark: Is ICS Training Achieving Its Goal

DTIC Science & Technology

2016-12-01

method achieves learning and actually gives students new knowledge, skills, and 281 Ibid. 282 Ibid...designed to be five days (40 hours) long.331 The class assumes that the student already has a general understanding of ICS and completion of at least...35–37. 64 The entire process is time consuming, as the student must complete the in- class time (as required for the specific class ) and

How consumers are affected by product descriptions in online shopping: Event-related potentials evidence of the attribute framing effect.

PubMed

Jin, Jia; Zhang, Wuke; Chen, Mingliang

2017-12-01

Due to the limitations of the human ability to process information, e-consumers' decisions are likely to be influenced by various cognitive biases, such as the attribute framing effect. This effect has been well studied by numerous scholars; however, the associated underlying neural mechanisms with a critical temporal resolution have not been revealed. Thus, this study applies the measurement of event-related potentials (ERPs) to directly examine the role of attribute framing in information processing and decision-making in online shopping. The behavioral results showed that participants demonstrated a higher purchase intention with a shorter reaction time under a positive framing condition compared to participants under a negative framing condition. Compared with positive framing messages, the results of ERPs indicated that negative framing messages attracted more attention resources at the early stage of rapid automatic processing (larger P2 amplitude) and resulted in greater cognitive conflict and decision difficulty (larger P2-N2 complex). Moreover, compared with negative messages, positive framing messages allowed consumers to perceive a better future performance of products and classify these products as a categorization of higher evaluation (larger LPP amplitude) at the late cognitive processing stage of evaluation. Based on these results, we provide evidence for a better understanding of how different attribute framing messages are processed and ultimately lead to the framing effect. Copyright © 2017 Elsevier Ireland Ltd and Japan Neuroscience Society. All rights reserved.

Perception of oyster-based products by French consumers. The effect of processing and role of social representations.

PubMed

Debucquet, Gervaise; Cornet, Josiane; Adam, Isabelle; Cardinal, Mireille

2012-12-01

The search for new markets in the seafood sector, associated with the question of the continuity of raw oyster consumption over generations can be an opportunity for processors to extend their ranges with oyster-based products. The twofold aim of this study was to evaluate the impact of processing and social representation on perception of oyster-based products by French consumers and to identify the best means of development in order to avoid possible failure in the market. Five products with different degrees of processing (cooked oysters in a half-shell, hot preparation for toast, potted oyster, oyster butter and oyster-based soup) were presented within focus groups and consumer tests, at home and in canteens with the staff of several companies in order to reach consumers with different ages and professional activities. The results showed that social representation had a strong impact and that behaviours were contrasted according to the initial profile of the consumer (traditional raw oyster consumers or non-consumers) and their age distribution (younger and older people). The degree of processing has to be adapted to each segment. It is suggested to develop early exposure to influence the food choices and preferences of the youngest consumers on a long-term basis. Copyright © 2012 Elsevier Ltd. All rights reserved.

Evaluation of a time efficient immunization strategy for anti-PAH antibody development

PubMed Central

Li, Xin; Kaattari, Stephen L.; Vogelbein, Mary Ann; Unger, Michael A.

2016-01-01

The development of monoclonal antibodies (mAb) with affinity to small molecules can be a time-consuming process. To evaluate shortening the time for mAb production, we examined mouse antisera at different time points post-immunization to measure titer and to evaluate the affinity to the immunogen PBA (pyrene butyric acid). Fusions were also conducted temporally to evaluate antibody production success at various time periods. We produced anti-PBA antibodies 7 weeks post-immunization and selected for anti-PAH reactivity during the hybridoma screening process. Moreover, there were no obvious sensitivity differences relative to antibodies screened from a more traditional 18 week schedule. Our results demonstrate a more time efficient immunization strategy for anti-PAH antibody development that may be applied to other small molecules. PMID:27282486

BigDebug: Debugging Primitives for Interactive Big Data Processing in Spark

PubMed Central

Gulzar, Muhammad Ali; Interlandi, Matteo; Yoo, Seunghyun; Tetali, Sai Deep; Condie, Tyson; Millstein, Todd; Kim, Miryung

2016-01-01

Developers use cloud computing platforms to process a large quantity of data in parallel when developing big data analytics. Debugging the massive parallel computations that run in today’s data-centers is time consuming and error-prone. To address this challenge, we design a set of interactive, real-time debugging primitives for big data processing in Apache Spark, the next generation data-intensive scalable cloud computing platform. This requires re-thinking the notion of step-through debugging in a traditional debugger such as gdb, because pausing the entire computation across distributed worker nodes causes significant delay and naively inspecting millions of records using a watchpoint is too time consuming for an end user. First, BIGDEBUG’s simulated breakpoints and on-demand watchpoints allow users to selectively examine distributed, intermediate data on the cloud with little overhead. Second, a user can also pinpoint a crash-inducing record and selectively resume relevant sub-computations after a quick fix. Third, a user can determine the root causes of errors (or delays) at the level of individual records through a fine-grained data provenance capability. Our evaluation shows that BIGDEBUG scales to terabytes and its record-level tracing incurs less than 25% overhead on average. It determines crash culprits orders of magnitude more accurately and provides up to 100% time saving compared to the baseline replay debugger. The results show that BIGDEBUG supports debugging at interactive speeds with minimal performance impact. PMID:27390389

Saving time and energy with oversubscription and semi-direct Møller-Plesset second order perturbation methods.

PubMed

Fought, Ellie L; Sundriyal, Vaibhav; Sosonkina, Masha; Windus, Theresa L

2017-04-30

In this work, the effect of oversubscription is evaluated, via calling 2n, 3n, or 4n processes for n physical cores, on semi-direct MP2 energy and gradient calculations and RI-MP2 energy calculations with the cc-pVTZ basis using NWChem. Results indicate that on both Intel and AMD platforms, oversubscription reduces total time to solution on average for semi-direct MP2 energy calculations by 25-45% and reduces total energy consumed by the CPU and DRAM on average by 10-15% on the Intel platform. Semi-direct gradient time to solution is shortened on average by 8-15% and energy consumption is decreased by 5-10%. Linear regression analysis shows a strong correlation between time to solution and total energy consumed. Oversubscribing during RI-MP2 calculations results in performance degradations of 30-50% at the 4n level. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Fast-tracking determination of homozygous transgenic lines and transgene stacking using a reliable quantitative real-time PCR assay.

PubMed

Wang, Xianghong; Jiang, Daiming; Yang, Daichang

2015-01-01

The selection of homozygous lines is a crucial step in the characterization of newly generated transgenic plants. This is particularly time- and labor-consuming when transgenic stacking is required. Here, we report a fast and accurate method based on quantitative real-time PCR with a rice gene RBE4 as a reference gene for selection of homozygous lines when using multiple transgenic stacking in rice. Use of this method allowed can be used to determine the stacking of up to three transgenes within four generations. Selection accuracy reached 100 % for a single locus and 92.3 % for two loci. This method confers distinct advantages over current transgenic research methodologies, as it is more accurate, rapid, and reliable. Therefore, this protocol could be used to efficiently select homozygous plants and to expedite time- and labor-consuming processes normally required for multiple transgene stacking. This protocol was standardized for determination of multiple gene stacking in molecular breeding via marker-assisted selection.

Estimating municipal solid waste generation by different activities and various resident groups: a case study of Beijing.

PubMed

Li, Zhen-shan; Fu, Hui-zhen; Qu, Xiao-yan

2011-09-15

Reliable and accurate determinations of the quantities and composition of wastes is required for the planning of municipal solid waste (MSW) management systems. A model, based on the interrelationships of expenditure on consumer goods, time distribution, daily activities, residents groups, and waste generation, was developed and employed to estimate MSW generation by different activities and resident groups in Beijing. The principle is that MSW is produced by consumption of consumer goods by residents in their daily activities: 'Maintenance' (meeting the basic needs of food, housing and personal care), 'Subsistence' (providing the financial requirements) and 'Leisure' (social and recreational pursuits) activities. Three series of important parameters - waste generation per unit of consumer expenditure, consumer expenditure distribution to activities in unit time, and time assignment to activities by different resident groups - were determined using a statistical analysis, a sampling survey and the Analytic Hierarchy Process, respectively. Data for analysis were obtained from the Beijing Statistical Yearbook (2004-2008) and questionnaire survey. The results reveal that 'Maintenance' activity produced the most MSW, distantly followed by 'Leisure' and 'Subsistence' activities. In 2008, in descending order of MSW generation the different resident groups were floating population, non-civil servants, retired people, civil servants, college students (including both undergraduates and graduates), primary and secondary students, and preschoolers. The new estimation model, which was successful in fitting waste generation by different activities and resident groups over the investigated years, was amenable to MSW prediction. Copyright © 2011 Elsevier B.V. All rights reserved.

Vision based tunnel inspection using non-rigid registration

NASA Astrophysics Data System (ADS)

Badshah, Amir; Ullah, Shan; Shahzad, Danish

2015-04-01

Growing numbers of long tunnels across the globe has increased the need for safety measurements and inspections of tunnels in these days. To avoid serious damages, tunnel inspection is highly recommended at regular intervals of time to find any deformations or cracks at the right time. While following the stringent safety and tunnel accessibility standards, conventional geodetic surveying using techniques of civil engineering and other manual and mechanical methods are time consuming and results in troublesome of routine life. An automatic tunnel inspection by image processing techniques using non rigid registration has been proposed. There are many other image processing methods used for image registration purposes. Most of the processes are operation of images in its spatial domain like finding edges and corners by Harris edge detection method. These methods are quite time consuming and fail for some or other reasons like for blurred or images with noise. Due to use of image features directly by these methods in the process, are known by the group, correlation by image features. The other method is featureless correlation, in which the images are converted into its frequency domain and then correlated with each other. The shift in spatial domain is the same as in frequency domain, but the processing is order faster than in spatial domain. In the proposed method modified normalized phase correlation has been used to find any shift between two images. As pre pre-processing the tunnel images i.e. reference and template are divided into small patches. All these relative patches are registered by the proposed modified normalized phase correlation. By the application of the proposed algorithm we get the pixel movement of the images. And then these pixels shifts are converted to measuring units like mm, cm etc. After the complete process if there is any shift in the tunnel at described points are located.

Trends in meat consumption in the United States

PubMed Central

Daniel, Carrie R.; Cross, Amanda J.; Koebnick, Corinna; Sinha, Rashmi

2010-01-01

OBJECTIVE To characterize the trends, distribution, potential determinants, and public health implications of meat consumption within the United States. DESIGN We examined temporal trends in meat consumption using food availability data from the Food and Agricultural Organization (FAO) and United States Department of Agriculture (USDA); and further evaluated meat intake by type (red, white, processed) in the National Health and Nutrition Examination Surveys (NHANES) linked to the MyPyramid Equivalents Database (MPED). RESULTS Overall meat consumption has continued to rise in the U.S., European Union, and developed world. Despite a shift toward higher poultry consumption, red meat still represents the largest proportion of meat consumed in the U.S (58%). Twenty-two percent of the meat consumed in the U.S. is processed. According to NHANES 2003–2004, total meat intake averaged 128 g/day. The type and quantities of meat reported varied by education, race, age, and gender. CONCLUSIONS Given the plausible epidemiologic evidence for red and processed meat intake in cancer and chronic disease risk, understanding the trends and determinants of meat consumption in the U.S., where meat is consumed at more than three times the global average, should be particularly pertinent to researchers and other public health professionals aiming to reduce the global burden of chronic disease. PMID:21070685

Consumer concerns and expectations about novel food processing technologies: effects on product liking.

PubMed

Cardello, Armand V

2003-06-01

Eighty-eight consumers participated in a blind pre-test in which they rated their baseline preference for chocolate pudding, their liking of three tasted brands of chocolate pudding, and their level of concern for 20 different food processing and preservation technologies. All returned one month later and tasted the same puddings, but this time they were informed that they had been processed by one of several different novel or traditional food processing techniques. Different sub-groups were informed of the name of the process, the name plus a factual description of the process, or the name, the factual description, plus a benefit statement. Ratings of expected liking were obtained before and after viewing the samples, but before tasting them. Finally, subjects tasted and rated the products for actual liking and a sub-group rated their concern levels for the same 20 technologies rated in the pre-test. Pre-test results showed females to have significantly higher concern levels for all technologies. Individuals who had demonstrated a willingness to consume foods processed by one novel technology (irradiation) had lower concern ratings for all technologies. Ratings of concern were negatively correlated with expected liking for products believed to be processed by the technologies. Expected liking ratings were positively influenced by visual exposure to the product and by a safety and benefit statement. Linear regression of the change in product liking as a function of whether products were better or worse than expected supported an assimilation model of the effect of disconfirmed expectations on liking/disliking. Lastly, post-test concern levels for many of the technologies were reduced by participation in the study.

78 FR 12331 - Request for Nominations for Voting and/or Nonvoting Consumer Representatives on Public Advisory...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-22

... Selection Process for Nominations for Voting and/or Nonvoting Consumer Representatives on Public Advisory... statements of interest from consumer organizations interested in participating in the selection process and... Evaluation and Vaccines and Related Biological Products. Research, 1401 Rockville Pike (HFM-71), Rockville...

The pivotal role of multimodality reporter sensors in drug discovery: from cell based assays to real time molecular imaging.

PubMed

Ray, Pritha

2011-04-01

Development and marketing of new drugs require stringent validation that are expensive and time consuming. Non-invasive multimodality molecular imaging using reporter genes holds great potential to expedite these processes at reduced cost. New generations of smarter molecular imaging strategies such as Split reporter, Bioluminescence resonance energy transfer, Multimodality fusion reporter technologies will further assist to streamline and shorten the drug discovery and developmental process. This review illustrates the importance and potential of molecular imaging using multimodality reporter genes in drug development at preclinical phases.

Multifractality of sectoral price indices: Hurst signature analysis of Cantillon effects in disequilibrium factor markets

NASA Astrophysics Data System (ADS)

Mulligan, Robert F.

2014-06-01

This paper presents Hurst exponent signatures from time series of aggregate price indices for the US over the 1975-2011 time period. Though all highly aggregated, these indices include both broad measures of consumer and producer prices. The constellation of prices evolves as a complex system throughout processes of production and distribution, culminating in the final delivery of output to consumers. Massive feedback characterizes this system, where the demand for consumable output determines the demand for the inputs used to produce it, and supply scarcities for the necessary inputs in turn determine the supply of the final product. Prices in both factor and output markets are jointly determined by interdependent supply and demand conditions. Fractal examination of the interplay among market prices would be of interest regardless, but added interest arises from the consideration of how these markets respond to external shocks over the business cycle, particularly monetary expansion. Because the initial impact of monetary injection is localized in specific sectors, the way the impact on prices diffuses throughout the economy is of special interest.

Advanced Signal Processing Analysis of Laser-Induced Breakdown Spectroscopy Data for the Discrimination of Obsidian Sources

DTIC Science & Technology

2012-02-09

different sources [12,13], but the analytical techniques needed for such analysis (XRD, INAA , & ICP-MS) are time consuming and require expensive...partial least-squares discriminant analysis (PLSDA) that used the SIMPLS solving method [33]. In the experi- ment design, a leave-one-sample-out (LOSO) para...REPORT Advanced signal processing analysis of laser-induced breakdown spectroscopy data for the discrimination of obsidian sources 14. ABSTRACT 16

USSR Report, Consumer Goods and Domestic Trade, No. 65

DTIC Science & Technology

1983-06-08

types of oil-bearing raw materials— grape seeds , fruit and tree-fruit pits, corn germs and others. In recent years the ties of the workers of oils and...brief, indicate how the original information was processed. Where no processing indicator is given, the information was summarized or extracted ...good crop. More than 2 million tons of grapes were harvested for the first time. Public education, science and culture underwent further development

[Collaborative application of BEPS at different time steps.

PubMed

Lu, Wei; Fan, Wen Yi; Tian, Tian

2016-09-01

BEPSHourly is committed to simulate the ecological and physiological process of vegetation at hourly time steps, and is often applied to analyze the diurnal change of gross primary productivity (GPP), net primary productivity (NPP) at site scale because of its more complex model structure and time-consuming solving process. However, daily photosynthetic rate calculation in BEPSDaily model is simpler and less time-consuming, not involving many iterative processes. It is suitable for simulating the regional primary productivity and analyzing the spatial distribution of regional carbon sources and sinks. According to the characteristics and applicability of BEPSDaily and BEPSHourly models, this paper proposed a method of collaborative application of BEPS at daily and hourly time steps. Firstly, BEPSHourly was used to optimize the main photosynthetic parameters: the maximum rate of carboxylation (V c max ) and the maximum rate of photosynthetic electron transport (J max ) at site scale, and then the two optimized parameters were introduced into BEPSDaily model to estimate regional NPP at regional scale. The results showed that optimization of the main photosynthesis parameters based on the flux data could improve the simulate ability of the model. The primary productivity of different forest types in descending order was deciduous broad-leaved forest, mixed forest, coniferous forest in 2011. The collaborative application of carbon cycle models at different steps proposed in this study could effectively optimize the main photosynthesis parameters V c max and J max , simulate the monthly averaged diurnal GPP, NPP, calculate the regional NPP, and analyze the spatial distribution of regional carbon sources and sinks.

Longitudinal Analysis of Nut-Inclusive Diets and Body Mass Index Among Overweight and Obese African American Women Living in Rural Alabama and Mississippi, 2011-2013.

PubMed

Sterling, Samara R; Bertrand, Brenda; Judd, Suzanne; Carson, Tiffany L; Chandler-Laney, Paula; Baskin, Monica L

2017-09-21

Nuts, when eaten alongside other nutritionally rich foods, may decrease obesity and related chronic disease risks, which are high among African American women in the rural South. We monitored changes in nut intake, other obesity-related foods (fruits, vegetables, red or processed meats, added sugars), and body mass index (BMI) over a 2-year weight loss intervention among 383 overweight and obese African American women in rural Alabama and Mississippi. Two dietary recalls were administered at 4 points over 24 months. Mann-Whitney tests compared differences in median food group intake between nut consumers and non-nut consumers, and t tests identified BMI differences between groups. Mixed linear models tested the relationship between nut intake and intake of the select food groups, and between nut intake and BMI over time. Overall nut consumers ate more fruits and vegetables and less red meat than non-nut consumers. Nut consumers had lower BMI values than non-nut consumers. Weight loss by the end of the intervention was significant for nut consumers but not for non-nut consumers, even after accounting for kilocalorie consumption and physical activity engagement. Nut consumption is associated with consumption of other nutritionally rich foods and lower BMI among African American women in rural Alabama and Mississippi. Future interventions should target increasing daily nut intake, decreasing added sugar intake, and identifying strategies to encourage positive dietary changes to continue after an intervention.

Changes in seafood consumer preference patterns and associated changes in risk exposure.

PubMed

Jensen, Helen H

2006-01-01

Consumers world-wide are driving changes in the agriculture and food sector. Rising consumer income, changing demographics and lifestyles, and shifting preferences due to new information about the links between diet and health all contribute to new demands for foods. At the same time, technological changes in production, processing and distribution, growth in large-scale retailing, and changes in product availability, as well as expansion of trade world wide, have contributed to a rapidly changing market for food products. Changes in seafood consumption reflect these changes. The changes in consumer consumption patterns, new technologies and trade in product offer both expanded markets as well as new challenges to consumer exposure to food-borne risks. The strict quality control requirements of retail brokers, growth of private labels, and development of value-protecting marketing channels have become increasingly important in food markets. This paper addresses major trends that affect seafood consumption and the market for seafood products and the implications of these changes for consumer risk exposure to food safety hazards. The current economic environment highlights similarities and differences between the developed and developing countries, as well as diversity worldwide in consumption of seafood. Within this context, four major trends affect consumer consumption of foods, including seafood and fish products today: rising income; changing demographics; changing markets for food; and an increasingly global market for food products. Changes in consumer risk exposure to food safety problems are addressed in the context of these trends.

The Neuroscience of Consumer Choice

PubMed Central

Hsu, Ming; Yoon, Carolyn

2015-01-01

We review progress and challenges relating to scientific and applied goals of the nascent field of consumer neuroscience. Scientifically, substantial progress has been made in understanding the neurobiology of choice processes. Further advances, however, require researchers to begin clarifying the set of developmental and cognitive processes that shape and constrain choices. First, despite the centrality of preferences in theories of consumer choice, we still know little about where preferences come from and the underlying developmental processes. Second, the role of attention and memory processes in consumer choice remains poorly understood, despite importance ascribed to them in interpreting data from the field. The applied goal of consumer neuroscience concerns our ability to translate this understanding to augment prediction at the population level. Although the use of neuroscientific data for market-level predictions remains speculative, there is growing evidence of superiority in specific cases over existing market research techniques. PMID:26665152

Evaluating Mobile Graphics Processing Units (GPUs) for Real-Time Resource Constrained Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meredith, J; Conger, J; Liu, Y

2005-11-11

Modern graphics processing units (GPUs) can provide tremendous performance boosts for some applications beyond what a single CPU can accomplish, and their performance is growing at a rate faster than CPUs as well. Mobile GPUs available for laptops have the small form factor and low power requirements suitable for use in embedded processing. We evaluated several desktop and mobile GPUs and CPUs on traditional and non-traditional graphics tasks, as well as on the most time consuming pieces of a full hyperspectral imaging application. Accuracy remained high despite small differences in arithmetic operations like rounding. Performance improvements are summarized here relativemore » to a desktop Pentium 4 CPU.« less

P80 SRM low torque flex-seal development - thermal and chemical modeling of molding process

NASA Astrophysics Data System (ADS)

Descamps, C.; Gautronneau, E.; Rousseau, G.; Daurat, M.

2009-09-01

The development of the flex-seal component of the P80 nozzle gave the opportunity to set up new design and manufacturing process methods. Due to the short development lead time required by VEGA program, the usual manufacturing iterative tests work flow, which is usually time consuming, had to be enhanced in order to use a more predictive approach. A newly refined rubber vulcanization description was built up and identified on laboratory samples. This chemical model was implemented in a thermal analysis code. The complete model successfully supports the manufacturing processes. These activities were conducted with the support of ESA/CNES Research & Technologies and DGA (General Delegation for Armament).

Classification of Concepts in Consumer Education. Consumer Education Development Program: A National Study.

ERIC Educational Resources Information Center

Bannister, Rosella; Monsma, Charles

This guide for program planners and curriculum developers identifies and describes the basic concepts in consumer education. Consumer education is defined as the process of gaining the knowledge and skills needed in managing consumer resources and taking actions to influence the factors which affect consumer decisions. The primary focus of…

The role of production process and information on quality expectations and perceptions of sparkling wines.

PubMed

Vecchio, Riccardo; Lisanti, Maria Tiziana; Caracciolo, Francesco; Cembalo, Luigi; Gambuti, Angelita; Moio, Luigi; Siani, Tiziana; Marotta, Giuseppe; Nazzaro, Concetta; Piombino, Paola

2018-05-28

The present research aims to analyse, by combining sensory and experimental economics techniques, to what extent production process, and the information about it, may affect consumer preferences. Sparkling wines produced by Champenoise and Charmat methods were the object of the study. A quantitative descriptive sensory analysis with a trained panel and non-hypothetical auctions combined with hedonic ratings involving young wine consumers (N=100), under different information scenarios(Blind, Info and Info Taste), were performed. Findings show that the production process impacts both the sensory profile of sparkling wines and consumer expectations. In particular, the hedonic ratings revealed that when tasting the products, both with no information on the production process (Blind) and with such information (Info Taste), the consumers preferred the Charmat wines. On the contrary, when detailed information on the production methods was given without tasting (Info), consumers liked more the two Champenoise wines. It can be concluded that sensory and non-sensory attributes of sparkling wines affect consumers' preferences. Specifically, the study suggests that production process information strongly impacts liking expectations, while not affecting informed liking. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Influence of cognitive style on information processing and selection of yogurt labels: Insights from an eye-tracking study.

PubMed

Mawad, Franco; Trías, Marcela; Giménez, Ana; Maiche, Alejandro; Ares, Gastón

2015-08-01

Cognitive styles are characteristic and stable ways in which people acquire, organize and use information for solving problems and making decisions. Field dependence/independence is one of the most studied cognitive styles. Field independent subjects are characterized by having less difficulty in separating information from its contextual surroundings and being less likely to be influenced by external cues than field dependent individuals. The present work aimed at studying the influence of field dependence/independence cognitive style on consumers' visual processing and choice of yogurt labels. One hundred and thirty three consumers completed a choice conjoint task. They were asked to select their preferred yogurt label from each of 16 pairs of labels. While they completed the task their eye movements were recorded using an eye-tracker. Then, consumers were asked to complete the Group Embedded Figure Test to determine their cognitive style. Consumers were divided into two groups with different cognitive styles: 58% of the sample was characterized as field dependent and 42% as field independent. When making their choices, field dependent consumers tended to engage in less thoughtful information processing than field independent consumers and they made fewer fixations on traditional nutritional information. Besides, cognitive style significantly affected the relative importance of fat and sugar content on consumer choices and modulated the influence of the traffic light system. Field dependent consumers gave less importance to the nutritional composition of the yogurts than field independent consumers for selecting their preferred label. Results from this work suggest that studying the psychological underpinnings of consumers' decision making process when selecting food products has a great potential to contribute to a better understanding of how eating patterns and consumer preferences are shaped. Copyright © 2015 Elsevier Ltd. All rights reserved.

Microwave processing of gustatory tissues for immunohistochemistry

PubMed Central

Bond, Amanda; Kinnamon, John C.

2013-01-01

We use immunohistochemistry to study taste cell structure and function as a means to elucidate how taste receptor cells communicate with nerve fibers and adjacent taste cells. This conventional method, however, is time consuming. In the present study we used taste buds from rat circumvallate papillae to compare conventional immunohistochemical tissue processing with microwave processing for the colocalization of several biochemical pathway markers (PLCβ2, syntaxin-1, IP3R3, α-gustducin) and the nuclear stain, Sytox. The results of our study indicate that in microwave versus conventional immunocytochemistry: (1) fixation quality is improved; (2) the amount of time necessary for processing tissue is decreased; (3) antigen retrieval is no longer needed; (4) image quality is superior. In sum, microwave tissue processing of gustatory tissues is faster and superior to conventional immunohistochemical tissue processing for many applications. PMID:23473796

Public reporting in health care: how do consumers use quality-of-care information? A systematic review.

PubMed

Faber, Marjan; Bosch, Marije; Wollersheim, Hub; Leatherman, Sheila; Grol, Richard

2009-01-01

One of the underlying goals of public reporting is to encourage the consumer to select health care providers or health plans that offer comparatively better quality-of-care. To review the weight consumers give to quality-of-care information in the process of choice, to summarize the effect of presentation formats, and to examine the impact of quality information on consumers' choice behavior. The evidence is organized in a theoretical consumer choice model. English language literature was searched in PubMed, the Cochrane Clinical Trial, and the EPOC Databases (January 1990-January 2008). Study selection was limited to randomized controlled trails, controlled before-after trials or interrupted time series. Included interventions focused on choice behavior of consumers in health care settings. Outcome measures referred to one of the steps in a consumer choice model. The quality of the study design was rated, and studies with low quality ratings were excluded. All 14 included studies examine quality information, usually CAHPS, with respect to its impact on the consumer's choice of health plans. Easy-to-read presentation formats and explanatory messages improve knowledge about and attitude towards the use of quality information; however, the weight given to quality information depends on other features, including free provider choice and costs. In real-world settings, having seen quality information is a strong determinant for choosing higher quality-rated health plans. This review contributes to an understanding of consumer choice behavior in health care settings. The small number of included studies limits the strength of our conclusions.

10 CFR Appendix Y to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Battery Chargers

Code of Federal Regulations, 2011 CFR

2011-01-01

... power (i.e., watts) consumed as the time series integral of the power consumed over a 1-hour test period...) consumed as the time series integral of the power consumed over a 1-hour test period, divided by the period...-maintenance mode and standby mode over time periods defined in the test procedure. b. Active mode is the...

10 CFR Appendix Y to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Battery Chargers

Code of Federal Regulations, 2010 CFR

2010-01-01

... power (i.e., watts) consumed as the time series integral of the power consumed over a 1-hour test period...) consumed as the time series integral of the power consumed over a 1-hour test period, divided by the period...-maintenance mode and standby mode over time periods defined in the test procedure. b. Active mode is the...

A comparison of three feature selection methods for object-based classification of sub-decimeter resolution UltraCam-L imagery

USDA-ARS?s Scientific Manuscript database

The availability of numerous spectral, spatial, and contextual features with object-based image analysis (OBIA) renders the selection of optimal features a time consuming and subjective process. While several feature election methods have been used in conjunction with OBIA, a robust comparison of th...

Science under Scrutiny

ERIC Educational Resources Information Center

Wright, Lynne

2003-01-01

Increasingly, coordinators are undertaking a scrutiny of work in order to check standards in their subjects. This is done frequently for English and mathematics, where annual targets for attainment in year 6 have to be set, but less so for science. Carrying out a scrutiny of work can be a daunting and time-consuming process. Faced with a pile of…

Finding Quality Geometry Apps: Not as Simple as a[superscript 2] + b[superscript 2] = c[superscript 2

ERIC Educational Resources Information Center

Larkin, Kevin

2016-01-01

Trying to find quality apps for use in mathematics classes can be time consuming and bewildering. This article outlines a process for evaluating apps and provides teachers with access to comprehensive qualitative evaluations of 53 geometrical apps based on pedagogical, mathematical and cognitive fidelities.

Widening the Knowledge Acquisition Bottleneck for Constraint-Based Tutors

ERIC Educational Resources Information Center

Suraweera, Pramuditha; Mitrovic, Antonija; Martin, Brent

2010-01-01

Intelligent Tutoring Systems (ITS) are effective tools for education. However, developing them is a labour-intensive and time-consuming process. A major share of the effort is devoted to acquiring the domain knowledge that underlies the system's intelligence. The goal of this research is to reduce this knowledge acquisition bottleneck and better…

Automated Problem Generation in Learning Management Systems: A Tutorial

ERIC Educational Resources Information Center

Romero, Jaime; Rozano, Mercedes

2016-01-01

The benefits of solving problems have been widely acknowledged by literature. Its implementation in e-learning platforms can make easier its management and the learning process itself. However, its implementation can also become a very time-consuming task, particularly when the number of problems to generate is high. In this tutorial we describe a…

Semi-Automatic Grading of Students' Answers Written in Free Text

ERIC Educational Resources Information Center

Escudeiro, Nuno; Escudeiro, Paula; Cruz, Augusto

2011-01-01

The correct grading of free text answers to exam questions during an assessment process is time consuming and subject to fluctuations in the application of evaluation criteria, particularly when the number of answers is high (in the hundreds). In consequence of these fluctuations, inherent to human nature, and largely determined by emotional…

Expanding the Audience for the Performing Arts.

ERIC Educational Resources Information Center

Andreasen, Alan R.

Becoming involved in the arts is a process that involves movement through several stages, from disinterest to active attendance at and enthusiasm for performing arts events. Since target consumers at any time will differ in their placement on this continuum, marketing programs to expand arts audiences must first identify where each target segment…

Course Recommendation Based on Query Classification Approach

ERIC Educational Resources Information Center

Gulzar, Zameer; Leema, A. Anny

2018-01-01

This article describes how with a non-formal education, a scholar has to choose courses among various domains to meet the research aims. In spite of this, the availability of large number of courses, makes the process of selecting the appropriate course a tedious, time-consuming, and risky decision, and the course selection will directly affect…

Assessing the Effectiveness of a Computer Simulation for Teaching Ecological Experimental Design

ERIC Educational Resources Information Center

Stafford, Richard; Goodenough, Anne E.; Davies, Mark S.

2010-01-01

Designing manipulative ecological experiments is a complex and time-consuming process that is problematic to teach in traditional undergraduate classes. This study investigates the effectiveness of using a computer simulation--the Virtual Rocky Shore (VRS)--to facilitate rapid, student-centred learning of experimental design. We gave a series of…

Using Technology to Improve Fee Collection

ERIC Educational Resources Information Center

Schoenberg, Doug

2008-01-01

A child care center's financial health depends on collecting and processing payments. It is one of the most time-consuming and unpleasant administrative tasks. Fortunately, it's an area where the smart use of technology can provide dramatic benefits. This article discusses various tools and technologies that can be used by child care centers to…

Determination of Sulfate by Conductometric Titration: An Undergraduate Laboratory Experiment

ERIC Educational Resources Information Center

Garcia, Jennifer; Schultz, Linda D.

2016-01-01

The classic technique for sulfate analysis in an undergraduate quantitative analysis lab involves precipitation as the barium salt with barium chloride, collection of the precipitate by gravity filtration using ashless filter paper, and removal of the filter paper by charring over a Bunsen burner. The entire process is time-consuming, hazardous,…

Readerbench: Automated Evaluation of Collaboration Based on Cohesion and Dialogism

ERIC Educational Resources Information Center

Dascalu, Mihai; Trausan-Matu, Stefan; McNamara, Danielle S.; Dessus, Philippe

2015-01-01

As Computer-Supported Collaborative Learning (CSCL) gains a broader usage, the need for automated tools capable of supporting tutors in the time-consuming process of analyzing conversations becomes more pressing. Moreover, collaboration, which presumes the intertwining of ideas or points of view among participants, is a central element of dialogue…

Using a Group Approach to Motivate Adults to Learn Braille

ERIC Educational Resources Information Center

Farrow, Kendra R.

2015-01-01

Teaching braille is one of the most time-consuming tasks for a vision rehabilitation therapist. Complicating this process, adults who might be considered to be good candidates for learning braille are often resistant to the idea (Ponchillia & Ponchillia, 1996). In an attempt to address these challenges, a combination of correspondence braille…

What to Consider when Looking for International Teachers

ERIC Educational Resources Information Center

Mulder, Cris Galicia

2009-01-01

While many school leaders are enticed by the benefits international teachers bring to their schools, some find the process of attracting and hiring educators from other countries to be daunting. Many of the challenges relate to visas. Procuring them can be costly and time-consuming. Additionally, the No Child Left Behind definition of a highly…

Professional Development Portfolio: Perceptions of Nutrition and Dietetics Current Students and Recent Graduates

ERIC Educational Resources Information Center

Vouchilas, Gus; George, Gretchen

2016-01-01

The Professional Development Portfolio (PDP) in family and consumer sciences nutrition and dietetics programs is a tool that can help students in their transition to professionals. Significant issues in the portfolio development process are: content selection, decision to create paper or online formatting, determination of proper timing to begin…

PROJECT SQUID. Field Survey Report. Volume 1, Part 3. Materials

DTIC Science & Technology

1947-06-30

are thought to deserve consideration as to rfrator meals iththoe otaie~l y tit~kl~~lj materials of construction ,titanium, tungsten, tanta- tion of...provide This is a time.consuming costly process with no guar - the n. (, .d data. antee of achieving optimum results. The determina- tion of the

Simulating the fate of fall- and spring-applied poultry litter nitrogen in corn production

USDA-ARS?s Scientific Manuscript database

Monitoring the fate of N derived from manures applied to fertilize crops is difficult, time consuming, and relatively expensive. But computer simulation models can help understand the interactions among various N processes in the soil-plant system and determine the fate of applied N. The RZWQM2 was ...

EFL Students' Perceptions of Corpus-Tools as Writing References

ERIC Educational Resources Information Center

Lai, Shu-Li

2015-01-01

A number of studies have suggested the potentials of corpus tools in vocabulary learning. However, there are still some concerns. Corpus tools might be too complicated to use; example sentences retrieved from corpus tools might be too difficult to understand; processing large number of sample sentences could be challenging and time-consuming;…

Automatic Coding of Dialogue Acts in Collaboration Protocols

ERIC Educational Resources Information Center

Erkens, Gijsbert; Janssen, Jeroen

2008-01-01

Although protocol analysis can be an important tool for researchers to investigate the process of collaboration and communication, the use of this method of analysis can be time consuming. Hence, an automatic coding procedure for coding dialogue acts was developed. This procedure helps to determine the communicative function of messages in online…

The Professors behind the MOOC Hype

ERIC Educational Resources Information Center

Kolowich, Steve

2013-01-01

The largest-ever survey of professors who have taught MOOCs, or massive open online courses, shows that the process is time-consuming, but, according to the instructors, often successful. Nearly half of the professors felt their online courses were as rigorous academically as the versions they taught in the classroom. The survey, conducted by "The…

Development of a Time-Intensity Evaluation System for Consumers: Measuring Bitterness and Retronasal Aroma of Coffee Beverages in 106 Untrained Panelists.

PubMed

Gotow, Naomi; Moritani, Ami; Hayakawa, Yoshinobu; Akutagawa, Akihito; Hashimoto, Hiroshi; Kobayakawa, Tatsu

2015-06-01

In order to develop products that are acceptable to consumers, it is necessary to incorporate consumers' intentions into products' characteristics. Therefore, investigation of consumers' perceptions of the taste or smell of common beverages provides information that should be useful in predicting market responses. In this study, we sought to develop a time-intensity evaluation system for consumer panels. Using our system, we performed time-intensity evaluation of flavor attributes (bitterness and retronasal aroma) that consumers perceived after swallowing a coffee beverage. Additionally, we developed quantitative evaluation methods for determining whether consumer panelists can properly perform time-intensity evaluation. In every trial, we fitted an exponential function to measured intensity data for bitterness and retronasal aroma. The correlation coefficients between measured time-intensity data and the fitted exponential curves were greater than 0.8 in about 90% of trials, indicating that we had successfully developed a time-intensity system for use with consumer panelists, even after just a single training trial using a nontrained consumer. We classified participants into two groups based on their consumption of canned coffee beverages. Significant difference was observed in only AUC of sensory modality (bitterness compared with retronasal aroma) among conventional TI parameters using two-way ANOVA. However, three-way ANOVA including a time course revealed significant difference between bitterness and retronasal aroma in the high-consumption group. Moreover, the high-consumption group more easily discriminated between bitterness and retronasal aroma than the low-consumption group. This finding implied that manufacturers should select consumer panelists who are suitable for their concepts of new products. © 2015 Institute of Food Technologists®

How Do Patients Choose Physicians? Evidence from a National Survey of Enrollees in Employment-Related Health Plans

PubMed Central

Harris, Katherine M

2003-01-01

Objective This study examines the process by which patients search for and choose physicians. Data Source A survey to a random sample of individuals between the ages of 21 and 64 with employer-related health benefits, drawn from a nationally representative panel of households. Study Design Logit models are used to measure the effect of patient characteristics on the probability of (1) using alternative sources of information to support the choice of a current physician, (2) seriously considering another physician before choosing a current physician, and (3) stating a willingness to switch physicians when information suggests that other health plan doctors receive higher quality ratings. Principal Findings Although a minority of respondents actively searches for a physician, there appears to be substantial variation in the degree of consumer activism across patient subgroups. Poor health status, higher levels of service use in the past year, and stronger ties to individual physicians are associated with less consumer activism. At the same time, greater levels of consumer activism were found among racial and ethnic minorities, among those who report using information to choose their physicians, and among those who switched physicians as a result of dissatisfaction some time in the past five years. Source of quality information (medical experts versus patient advocates) did not influence stated willingness to switch physicians. Conclusions Despite predictions of the increasing importance of consumer choice in shaping the health care delivery system, the results largely confirm the image depicted in the previous literature of patients as passive health care consumers of physician services, and highlight the importance of investments in the development of decision support tools in consumer-driven health care systems. PMID:12785569

Encryption and decryption algorithm using algebraic matrix approach

NASA Astrophysics Data System (ADS)

Thiagarajan, K.; Balasubramanian, P.; Nagaraj, J.; Padmashree, J.

2018-04-01

Cryptographic algorithms provide security of data against attacks during encryption and decryption. However, they are computationally intensive process which consume large amount of CPU time and space at time of encryption and decryption. The goal of this paper is to study the encryption and decryption algorithm and to find space complexity of the encrypted and decrypted data by using of algorithm. In this paper, we encrypt and decrypt the message using key with the help of cyclic square matrix provides the approach applicable for any number of words having more number of characters and longest word. Also we discussed about the time complexity of the algorithm. The proposed algorithm is simple but difficult to break the process.

Collaboration as a process and an outcome: Consumer experiences of collaborating with nurses in care planning in an acute inpatient mental health unit.

PubMed

Reid, Rebecca; Escott, Phil; Isobel, Sophie

2018-04-14

This qualitative study explores inpatient mental health consumer perceptions of how collaborative care planning with mental health nurses impacts personal recovery. Semi-structured interviews were conducted with consumers close to discharge from one unit in Sydney, Australia. The unit had been undertaking a collaborative care planning project which encouraged nurses to use care plan documentation to promote person-centred and goal-focussed interactions and the development of meaningful strategies to aid consumer recovery. The interviews explored consumer understandings of the collaborative care planning process, perceptions of the utility of the care plan document and the process of collaborating with the nurses, and their perception of the impact of collaboration on their recovery. Findings are presented under four organizing themes: the process of collaborating, the purpose of collaborating, the nurse as collaborator and the role of collaboration in wider care and recovery. Consumers highlighted the importance of the process of developing their care plan with a nurse as being as helpful for recovery as the goals and strategies themselves. The findings provide insights into consumers' experiences of care planning in an acute inpatient unit, the components of care that support recovery and highlight specific areas for mental health nursing practice improvement in collaboration. © 2018 Australian College of Mental Health Nurses Inc.

FRAME (Force Review Automation Environment): MATLAB-based AFM data processor.

PubMed

Partola, Kostyantyn R; Lykotrafitis, George

2016-05-03

Data processing of force-displacement curves generated by atomic force microscopes (AFMs) for elastic moduli and unbinding event measurements is very time consuming and susceptible to user error or bias. There is an evident need for consistent, dependable, and easy-to-use AFM data processing software. We have developed an open-source software application, the force review automation environment (or FRAME), that provides users with an intuitive graphical user interface, automating data processing, and tools for expediting manual processing. We did not observe a significant difference between manually processed and automatically processed results from the same data sets. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assesment on the performance of electrode arrays using image processing technique

NASA Astrophysics Data System (ADS)

Usman, N.; Khiruddin, A.; Nawawi, Mohd

2017-08-01

Interpreting inverted resistivity section is time consuming, tedious and requires other sources of information to be relevant geologically. Image processing technique was used in order to perform post inversion processing which make geophysical data interpretation easier. The inverted data sets were imported into the PCI Geomatica 9.0.1 for further processing. The data sets were clipped and merged together in order to match the coordinates of the three layers and permit pixel to pixel analysis. Dipole-dipole array is more sensitive to resistivity variation with depth in comparison with Werner-Schlumberger and pole-dipole. Image processing serves as good post-inversion tool in geophysical data processing.

Self-Calibrated In-Process Photogrammetry for Large Raw Part Measurement and Alignment before Machining

PubMed Central

Mendikute, Alberto; Zatarain, Mikel; Bertelsen, Álvaro; Leizea, Ibai

2017-01-01

Photogrammetry methods are being used more and more as a 3D technique for large scale metrology applications in industry. Optical targets are placed on an object and images are taken around it, where measuring traceability is provided by precise off-process pre-calibrated digital cameras and scale bars. According to the 2D target image coordinates, target 3D coordinates and camera views are jointly computed. One of the applications of photogrammetry is the measurement of raw part surfaces prior to its machining. For this application, post-process bundle adjustment has usually been adopted for computing the 3D scene. With that approach, a high computation time is observed, leading in practice to time consuming and user dependent iterative review and re-processing procedures until an adequate set of images is taken, limiting its potential for fast, easy-to-use, and precise measurements. In this paper, a new efficient procedure is presented for solving the bundle adjustment problem in portable photogrammetry. In-process bundle computing capability is demonstrated on a consumer grade desktop PC, enabling quasi real time 2D image and 3D scene computing. Additionally, a method for the self-calibration of camera and lens distortion has been integrated into the in-process approach due to its potential for highest precision when using low cost non-specialized digital cameras. Measurement traceability is set only by scale bars available in the measuring scene, avoiding the uncertainty contribution of off-process camera calibration procedures or the use of special purpose calibration artifacts. The developed self-calibrated in-process photogrammetry has been evaluated both in a pilot case scenario and in industrial scenarios for raw part measurement, showing a total in-process computing time typically below 1 s per image up to a maximum of 2 s during the last stages of the computed industrial scenes, along with a relative precision of 1/10,000 (e.g., 0.1 mm error in 1 m) with an error RMS below 0.2 pixels at image plane, ranging at the same performance reported for portable photogrammetry with precise off-process pre-calibrated cameras. PMID:28891946

Self-Calibrated In-Process Photogrammetry for Large Raw Part Measurement and Alignment before Machining.

PubMed

Mendikute, Alberto; Yagüe-Fabra, José A; Zatarain, Mikel; Bertelsen, Álvaro; Leizea, Ibai

2017-09-09

Photogrammetry methods are being used more and more as a 3D technique for large scale metrology applications in industry. Optical targets are placed on an object and images are taken around it, where measuring traceability is provided by precise off-process pre-calibrated digital cameras and scale bars. According to the 2D target image coordinates, target 3D coordinates and camera views are jointly computed. One of the applications of photogrammetry is the measurement of raw part surfaces prior to its machining. For this application, post-process bundle adjustment has usually been adopted for computing the 3D scene. With that approach, a high computation time is observed, leading in practice to time consuming and user dependent iterative review and re-processing procedures until an adequate set of images is taken, limiting its potential for fast, easy-to-use, and precise measurements. In this paper, a new efficient procedure is presented for solving the bundle adjustment problem in portable photogrammetry. In-process bundle computing capability is demonstrated on a consumer grade desktop PC, enabling quasi real time 2D image and 3D scene computing. Additionally, a method for the self-calibration of camera and lens distortion has been integrated into the in-process approach due to its potential for highest precision when using low cost non-specialized digital cameras. Measurement traceability is set only by scale bars available in the measuring scene, avoiding the uncertainty contribution of off-process camera calibration procedures or the use of special purpose calibration artifacts. The developed self-calibrated in-process photogrammetry has been evaluated both in a pilot case scenario and in industrial scenarios for raw part measurement, showing a total in-process computing time typically below 1 s per image up to a maximum of 2 s during the last stages of the computed industrial scenes, along with a relative precision of 1/10,000 (e.g. 0.1 mm error in 1 m) with an error RMS below 0.2 pixels at image plane, ranging at the same performance reported for portable photogrammetry with precise off-process pre-calibrated cameras.

A low-rank matrix recovery approach for energy efficient EEG acquisition for a wireless body area network.

PubMed

Majumdar, Angshul; Gogna, Anupriya; Ward, Rabab

2014-08-25

We address the problem of acquiring and transmitting EEG signals in Wireless Body Area Networks (WBAN) in an energy efficient fashion. In WBANs, the energy is consumed by three operations: sensing (sampling), processing and transmission. Previous studies only addressed the problem of reducing the transmission energy. For the first time, in this work, we propose a technique to reduce sensing and processing energy as well: this is achieved by randomly under-sampling the EEG signal. We depart from previous Compressed Sensing based approaches and formulate signal recovery (from under-sampled measurements) as a matrix completion problem. A new algorithm to solve the matrix completion problem is derived here. We test our proposed method and find that the reconstruction accuracy of our method is significantly better than state-of-the-art techniques; and we achieve this while saving sensing, processing and transmission energy. Simple power analysis shows that our proposed methodology consumes considerably less power compared to previous CS based techniques.

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2013 CFR

2013-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2014 CFR

2014-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2012 CFR

2012-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... time of consummation. The threshold amount in effect during a particular time period is the amount...

Predicting alcohol consumption and binge drinking in company employees: an application of planned behaviour and self-determination theories.

PubMed

Hagger, Martin S; Lonsdale, Adam J; Hein, Vello; Koka, Andre; Lintunen, Taru; Pasi, Heidi; Lindwall, Magnus; Rudolfsson, Lisa; Chatzisarantis, Nikos L D

2012-05-01

This study tested an integrated model of the psychosocial determinants of alcohol-related behaviour among company employees from four nations. A motivational sequence was proposed in which motivational orientations from self-determination theory influenced intentions to consume alcohol within guideline limits and alcohol-related behaviour via the mediation of the theory of planned behaviour variables of attitude, subjective norms, and perceived behavioural control (PBC). A three-wave prospective design using self-reported psychological and behavioural measures. Company employees (N= 486, males = 225, females = 261; M age = 30.41, SD= 8.31) from four nations (Estonia, Finland, Sweden, and UK) completed measures of autonomous and controlled motivation from self-determination theory, attitudes, subjective norms, PBC, intentions from the theory of planned behaviour, and self-reported measures of past alcohol consumption and binge-drinking occasions at the first time point (time 1). Follow-up psychological and behavioural measures were taken one month later (time 2) and follow-up behavioural measures taken a further 2 months later (time 3). Path analyses supported the motivational sequence with identified regulation (time 1), predicting intentions (time 1), and alcohol units consumed (time 2). The effects were indirect via the mediation of attitudes and PBC (time 1). A similar pattern of effects was found for the effect of time 2 psychological variables on time 3 units of alcohol consumed. There was little support for the effects of the psychological variables on binge-drinking behaviour. Findings provide new information on the psychosocial determinants of alcohol behaviour in company employees and the processes involved. Results may provide impetus for the development of interventions to reduce alcohol consumption. ©2011 The British Psychological Society.

Islamic value to the modification of BSC model (a case study in evaluating company performance)

NASA Astrophysics Data System (ADS)

Harwati; Permana, Y.

2017-12-01

Halal is the key word for the Muslim community in consuming goods or services. Providing halal products is the main focus for companies with the largest consumers from the Muslim community. Halal is not only from the ingredients but also from the process in its production. The purpose of this study is to design a model of performance measurement for a company in order to provide halal products. Balance Score Card (BSC) is used as a framework. BSC as a performance measurement system has advantages not only focus on financial aspect but also non finance. Islamic values are incorporated into four perspective of BSC. They are: Selection of sharia financial institutions in financial perspective, payment method by consumer in consumer perspective, number of product with halal certificate and menu clarify in internal business process perspective, then accuracy of payroll time in learning and growth perspective. The modified BSC model obtains 17 Key Performance Indicators (KPI). The model is applied in a culinary industry (restaurant). Structured questionnaires and scheduled interviews are used to collect the important data. The result show that these industry fail to meet 8 from total 17 KPI so performance achievement is only 70.81%, and only reach 22.58% in Islamic value aspect. This is recorded by the company as an input to improve their performance in order to compete in halal food business.

Social Computing and the Attention Economy

NASA Astrophysics Data System (ADS)

Huberman, Bernardo A.

2013-04-01

Social computing focuses on the interaction between social behavior and information, especially on how the latter propagates across social networks and is consumed and transformed in the process. At the same time the ubiquity of information has left it devoid of much monetary value. The scarce, and therefore valuable, resource is now attention, and its allocation gives rise to an attention economy that determines how content is consumed and propagated. Since two major factors involved in getting attention are novelty and popularity, we analyze the role that both play in attracting attention to web content and how to prioritize them in order to maximize it. We also demonstrate that the relative performance of strategies based on prioritizing either popularity or novelty exhibit an abrupt change around a critical value of the novelty decay time, resembling a phase transition.

Scalable Performance Measurement and Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamblin, Todd

2009-01-01

Concurrency levels in large-scale, distributed-memory supercomputers are rising exponentially. Modern machines may contain 100,000 or more microprocessor cores, and the largest of these, IBM's Blue Gene/L, contains over 200,000 cores. Future systems are expected to support millions of concurrent tasks. In this dissertation, we focus on efficient techniques for measuring and analyzing the performance of applications running on very large parallel machines. Tuning the performance of large-scale applications can be a subtle and time-consuming task because application developers must measure and interpret data from many independent processes. While the volume of the raw data scales linearly with the number ofmore » tasks in the running system, the number of tasks is growing exponentially, and data for even small systems quickly becomes unmanageable. Transporting performance data from so many processes over a network can perturb application performance and make measurements inaccurate, and storing such data would require a prohibitive amount of space. Moreover, even if it were stored, analyzing the data would be extremely time-consuming. In this dissertation, we present novel methods for reducing performance data volume. The first draws on multi-scale wavelet techniques from signal processing to compress systemwide, time-varying load-balance data. The second uses statistical sampling to select a small subset of running processes to generate low-volume traces. A third approach combines sampling and wavelet compression to stratify performance data adaptively at run-time and to reduce further the cost of sampled tracing. We have integrated these approaches into Libra, a toolset for scalable load-balance analysis. We present Libra and show how it can be used to analyze data from large scientific applications scalably.« less

Improve the Efficiency of the Service Process as a Result of the Muda Ideology

NASA Astrophysics Data System (ADS)

Lorenc, Augustyn; Przyłuski, Krzysztof

2018-06-01

The aim of the paper was to improve service processes carried out by Knorr-Bremse Systemy Kolejowe Polska sp. z o.o. Particularly, emphasise unnecessary movements and physical efforts of employees. The indirect goal was to find a solution in the simplest possible way using the Muda ideology. In order to improve the service process at the beginning was executed the process mapping for the devices to be repaired, ie. brake callipers, electro-hydraulic units and auxiliary release units. The processes were assessed and shown as Pareto-Lorenz analysis. In order to determine the most time consuming process. Based on the obtained results use of a column crane with articulated arm was proposed to facilitate the transfer of heavy components between areas. The final step was to assess the effectiveness of the proposed solution in terms of time saving. From the company perspective results of the analysis are important. The proposed solution not only reduces total service time but also contributes to crew's work comfort.

Consumer Decision Making in a Global Context.

ERIC Educational Resources Information Center

Lusby, Linda A.

This document examines the underlying rationale for the development of a global approach in consumer studies. The concept of consumer ethics is discussed and the consumer decision-making process is placed within an ecosystem perspective of the marketplace. The model developed introduces educators, marketers, and consumers to a more global…

7 CFR 1215.13 - Process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Definitions § 1215.13 Process. Process means to shell, clean, dry, and prepare popcorn for the market, but does not include...

7 CFR 1215.13 - Process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Definitions § 1215.13 Process. Process means to shell, clean, dry, and prepare popcorn for the market, but does not include...

7 CFR 1215.13 - Process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Definitions § 1215.13 Process. Process means to shell, clean, dry, and prepare popcorn for the market, but does not include...

7 CFR 1215.13 - Process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Definitions § 1215.13 Process. Process means to shell, clean, dry, and prepare popcorn for the market, but does not include...

7 CFR 1215.13 - Process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POPCORN PROMOTION, RESEARCH, AND CONSUMER INFORMATION Popcorn Promotion, Research, and Consumer Information Order Definitions § 1215.13 Process. Process means to shell, clean, dry, and prepare popcorn for the market, but does not include...

12 CFR Supplement I to Part 1005 - Official Interpretations

Code of Federal Regulations, 2013 CFR

2013-01-01

... used to capture the Magnetic Ink Character Recognition (MICR) encoding to initiate a one-time automated clearinghouse (ACH) debit. For example, if a consumer authorizes a one-time ACH debit from the consumer's... involved at the time of the transaction, if the consumer's asset account is subsequently debited for the...

12 CFR Supplement I to Part 1005 - Official Interpretations

Code of Federal Regulations, 2012 CFR

2012-01-01

... used to capture the Magnetic Ink Character Recognition (MICR) encoding to initiate a one-time automated clearinghouse (ACH) debit. For example, if a consumer authorizes a one-time ACH debit from the consumer's... involved at the time of the transaction, if the consumer's asset account is subsequently debited for the...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2014 CFR

2014-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

12 CFR 1005.3 - Coverage.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-time electronic fund transfer from a consumer's account. The consumer must authorize the transfer. (ii... one-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR... transfer. A consumer authorizes a one-time electronic fund transfer from his or her account to pay the fee...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2011 CFR

2011-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

12 CFR 205.3 - Coverage.

Code of Federal Regulations, 2013 CFR

2013-01-01

... to initiate a one-time electronic fund transfer from a consumer's account. The consumer must...-time electronic fund transfer (in providing a check to a merchant or other payee for the MICR encoding... information for the transfer shall also provide a notice to the consumer at the same time it provides the...

An Empirical Study of Combining Communicating Processes in a Parallel Discrete Event Simulation

DTIC Science & Technology

1990-12-01

dynamics of the cost/performance criteria which typically made up computer resource acquisition decisions . offering a broad range of tradeoffs in the way... prcesses has a significant impact on simulation performance. It is the hypothesis of this 3-4 SYSTEM DECOMPOSITION PHYSICAL SYSTEM 1: N PHYSICAL PROCESS 1...EMPTY)) next-event = pop(next-event-queue); lp-clock = next-event - time; Simulate next event departure- consume event-enqueue new event end while; If no

Increase The Sugar Concentration of The Solution Sugar by Reverse Osmotic Membrane

NASA Astrophysics Data System (ADS)

Redjeki, S.; Hapsari, N.; Iriani

2018-01-01

Sugar is one of the basic needs of people and food and drink industry. As technology advances and the demand for efficient usage of sugar rises, crystal sugar is seen as less advantageous than liquid sugar. If sugar is always dissolved in water before use, then it will be more efficient and practical for consumers to use sugar in liquid form than in crystal form. Other than that, liquid sugar is also attractive to consumers because it is economical, hygienic, instantly soluble in hot and cold water, fresher and longer-lasting, able to thicken and enrich the texture of foods and drinks, and functions as sweetener, syrup, and flavor enhancer. Liquid sugar is also more beneficial for sugar producers because of simpler production process, cheaper production cost, and similar yield with no extra cost. In sugar production, separation process is found in most of its stages and therefore the use of membrane technology for separating solute and water content has a good potential. In this research, water content reduction of sugar solution was done in order to increase the sugar concentration of the solution. The parameters of this research were 4%, 5%, and 6% starting concentration of sugar solution; 20, 40, and 60 minutes of process time; and 85 and 60 PSI ΔP. The best result was acquired on 4% starting concentration, 60 PSI ΔP, and 60 minutes process time.

New analytic results for speciation times in neutral models.

PubMed

Gernhard, Tanja

2008-05-01

In this paper, we investigate the standard Yule model, and a recently studied model of speciation and extinction, the "critical branching process." We develop an analytic way-as opposed to the common simulation approach-for calculating the speciation times in a reconstructed phylogenetic tree. Simple expressions for the density and the moments of the speciation times are obtained. Methods for dating a speciation event become valuable, if for the reconstructed phylogenetic trees, no time scale is available. A missing time scale could be due to supertree methods, morphological data, or molecular data which violates the molecular clock. Our analytic approach is, in particular, useful for the model with extinction, since simulations of birth-death processes which are conditioned on obtaining n extant species today are quite delicate. Further, simulations are very time consuming for big n under both models.

Knowledge Reasoning with Semantic Data for Real-Time Data Processing in Smart Factory

PubMed Central

Wang, Shiyong; Li, Di; Liu, Chengliang

2018-01-01

The application of high-bandwidth networks and cloud computing in manufacturing systems will be followed by mass data. Industrial data analysis plays important roles in condition monitoring, performance optimization, flexibility, and transparency of the manufacturing system. However, the currently existing architectures are mainly for offline data analysis, not suitable for real-time data processing. In this paper, we first define the smart factory as a cloud-assisted and self-organized manufacturing system in which physical entities such as machines, conveyors, and products organize production through intelligent negotiation and the cloud supervises this self-organized process for fault detection and troubleshooting based on data analysis. Then, we propose a scheme to integrate knowledge reasoning and semantic data where the reasoning engine processes the ontology model with real time semantic data coming from the production process. Based on these ideas, we build a benchmarking system for smart candy packing application that supports direct consumer customization and flexible hybrid production, and the data are collected and processed in real time for fault diagnosis and statistical analysis. PMID:29415444

Real-time parameter optimization based on neural network for smart injection molding

NASA Astrophysics Data System (ADS)

Lee, H.; Liau, Y.; Ryu, K.

2018-03-01

The manufacturing industry has been facing several challenges, including sustainability, performance and quality of production. Manufacturers attempt to enhance the competitiveness of companies by implementing CPS (Cyber-Physical Systems) through the convergence of IoT(Internet of Things) and ICT(Information & Communication Technology) in the manufacturing process level. Injection molding process has a short cycle time and high productivity. This features have been making it suitable for mass production. In addition, this process is used to produce precise parts in various industry fields such as automobiles, optics and medical devices. Injection molding process has a mixture of discrete and continuous variables. In order to optimized the quality, variables that is generated in the injection molding process must be considered. Furthermore, Optimal parameter setting is time-consuming work to predict the optimum quality of the product. Since the process parameter cannot be easily corrected during the process execution. In this research, we propose a neural network based real-time process parameter optimization methodology that sets optimal process parameters by using mold data, molding machine data, and response data. This paper is expected to have academic contribution as a novel study of parameter optimization during production compare with pre - production parameter optimization in typical studies.

Does appraisal enhance learning, improve practice and encourage continuing professional development? A survey of general practitioners' experiences of appraisal.

PubMed

Finlay, Karen; McLaren, Susan

2009-01-01

Revalidation of the medical profession is under review and a system has been proposed to ensure doctors meet standards of practice and professionalism. The current appraisal system allows clinicians to chart their progress and identify developmental needs in order to improve performance. Appraisal is now an annual compulsory requirement for all doctors. The aim of the study was to investigate the experiences of general practitioners (GPs) of the current appraisal process. The specific objectives were to consider the impact the appraisal process had exerted on their learning, practice and individual continuing professional development (CPD). We employed a cross-sectional design using a postal questionnaire sent to all doctors who work as GPs (n = 385) in West Kent. Questionnaires were returned from 71.7% of doctors (n = 276). The key findings obtained were that 47.5% (n = 131) of doctors stated that taking part in the appraisal process had enhanced their learning, 40.2% (n = 111) felt that the appraisal process had improved their practice and 55.8% (n = 154) stated that the appraisal process had encouraged their CPD. Qualitative findings derived from thematic analysis of open questions revealed that participants viewed the role of the appraiser as respected peer to be vital and there was a need for independence in the appraiser's appointment. The time-consuming nature of the appraisal process was emphasised, with little protected time for preparation of documentation and engagement in CPD. Concerns were expressed about links between appraisal and revalidation. Many doctors considered that the appraisal process had enhanced their learning, improved their practice and encouraged their CPD. A vital, independent role for the appraiser was emphasised as was a need to review the time-consuming nature of the current appraisal process, together with identifying protected time to complete this and CPD engagement. As the role of appraisal within the revalidation process changes it is recognised that ensuring the quality, consistency and nature of appraisal will be essential to maintain the confidence of patients and doctors.

Consumer evaluation of food with nutritional benefits: a systematic review and narrative synthesis.

PubMed

Mogendi, Joseph Birundu; De Steur, Hans; Gellynck, Xavier; Makokha, Anselimo

2016-06-01

As a consequence of the growing interest in, and development of, various types of food with nutritional benefits, the modern consumer views their kitchen cabinet more and more as a medicine cabinet. Given that consumer evaluation of food is considered key to the successful production, marketing and finally consumption of food, a procedure commonly used in medical fields was employed to systematically review and summarize evidence of consumer evaluation studies on nutritious foods. The focus is primarily on consumer understanding of nutritious food and the underlying determinants of consumer evaluation. Our results highlight four groups of key determinants: (1) nutrition knowledge and information; (2) attitudes, beliefs, perceptions and behavioural determinants; (3) price, process and product characteristics; and (4) socio-demographics. The findings also point to the importance of understanding consumer acceptance as one many concepts in the consumer evaluation process, and provide support for developing appropriate strategies for improving health and well-being of consumers.

Characteristics study of the gears by the CAD/CAE

NASA Astrophysics Data System (ADS)

Wang, P. Y.; Chang, S. L.; Lee, B. Y.; Nguyen, D. H.; Cao, C. W.

2017-09-01

Gears are the most important transmission component in machines. The rapid development of the machines in industry requires a shorter time of the analysis process. In traditional, the gears are analyzed by setting up the complete mathematical model firstly, considering the profile of cutter and coordinate systems relationship between the machine and the cutter. It is a really complex and time-consuming process. Recently, the CAD/CAE software is well developed and useful in the mechanical design. In this paper, the Autodesk Inventor® software is introduced to model the spherical gears firstly, and then the models can also be transferred into ANSYS Workbench for the finite element analysis. The proposed process in this paper is helpful to the engineers to speed up the analyzing process of gears in the design stage.

Consumer attitude and purchase intention towards processed meat products with natural compounds and a reduced level of nitrite.

PubMed

Hung, Yung; de Kok, Theo M; Verbeke, Wim

2016-11-01

This study investigates consumer attitude and purchase intention towards processed meat products with added natural compounds and a reduced level of nitrite. The rationale for such innovation relates to nitrite's negative health image as a chemical additive among consumers, versus the perception of compounds from fruits and vegetables as being natural and healthy. Cross-sectional data were collected through online questionnaires on knowledge about, interest in, attitude and intentions towards such new type of processed meat products in Belgium, The Netherlands, Italy and Germany (n=2057). Consumers generally had limited knowledge about nitrite being added to meat products. Yet, they expressed favourable attitudes and purchase intentions towards the new processed meat products. Purchase intention associated positively with: attitude; preference for natural over chemical additives; perceived harmfulness of chemical additives; risk importance; domain specific innovativeness; awareness of nitrite added; education; general health interest; and processed meat consumption frequency. Consumers from Italy and Germany had a lower level of purchase intention compared to Belgium. Four consumer segments were identified based on attitude and purchase intention: 'enthusiasts' (39.3% of the sample), 'accepters' (11.9%), 'half-hearted' (42.3%) and 'uninterested' (6.6%). This study provides valuable insight for further product development and effective tailoring of marketing communication strategies of innovative processed meat products. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effect of non-caloric sweeteners on cognition, choice, and post-consumption satisfaction.

PubMed

Hill, Sarah E; Prokosch, Marjorie L; Morin, Amanda; Rodeheffer, Christopher D

2014-12-01

Consumers often turn to non-caloric sweeteners (NCS) as a means of promoting a healthy body weight. However, several studies have now linked their long-term use to increased weight gain, raising the question of whether these products produce unintended psychological, physiological, or behavioral changes that have implications for weight management goals. In the following, we present the results of three experiments bearing on this issue, testing whether NCS-consumption influences how individuals think about and respond to food. Participants in each of our three experiments were randomly assigned to consume a sugar-sweetened beverage, an unsweetened beverage, or a beverage sweetened with NCS. We then measured their cognition (Experiment 1), product choice (Experiment 2), and subjective responses to a sugar-sweetened food (Experiment 3). Results revealed that consuming NCS-sweetened beverages influences psychological processes in ways that - over time - may increase calorie intake. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mechanically Milled Irregular Zinc Nanoparticles for Printable Bioresorbable Electronics.

PubMed

Mahajan, Bikram K; Yu, Xiaowei; Shou, Wan; Pan, Heng; Huang, Xian

2017-05-01

Bioresorbable electronics is predominantly realized by complex and time-consuming anhydrous fabrication processes. New technology explores printable methods using inks containing micro- or nano-bioresorbable particles (e.g., Zn and Mg). However, these particles have seldom been obtained in the context of bioresorbable electronics using cheap, reliable, and effective approaches with limited study on properties essential to printable electronics. Here, irregular nanocrystalline Zn with controllable sizes and optimized electrical performance is obtained through ball milling approach using polyvinylpyrrolidone (PVP) as a process control agent to stabilize Zn particles and prevent cold welding. Time and PVP dependence of the ball milled particles are studied with systematic characterizations of morphology and composition of the nanoparticles. The results reveal crystallized Zn nanoparticles with a size of ≈34.834 ± 1.76 nm and low surface oxidation. The resulting Zn nanoparticles can be readily printed onto bioresorbable substrates and sintered at room temperature using a photonic sintering approach, leading to a high conductivity of 44 643 S m -1 for printable zinc nanoparticles. The techniques to obtain Zn nanoparticles through ball milling and processing them through photonic sintering may potentially lead to a mass fabrication method for bioresorbable electronics and promote its applications in healthcare, environmental protection, and consumer electronics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hypothesis regarding the transformation of the intended direction of movement during the production of graphic trajectories: a study of drawing movements in 8- to 12-year-old children.

PubMed

Pellizzer, Giuseppe; Zesiger, Pascal

2009-03-01

Children from 8 to 12 years of age drew figure-eights and ellipses at a self-chosen tempo on a digitizing tablet. Global aspects (perimeter and average speed) and local aspects (relation between instantaneous speed and curvature) of performance were analyzed across age groups and types of figures. We tested the predictions of the transformation model, which is based on the hypothesis that changing the intended direction of movement is a time-consuming process that affects the evolution in time of the movement trajectory, and compared how well it fitted the data relative to the power law. We found that the relation between speed and curvature was typically better described by the transformation model than by the power law. However, the power law provided a better description when ellipses were drawn at a fast speed. The analyses of the parameters of the transformation model indicate that processing speed increased linearly with age. In addition, the results suggest that the effects of the spring-like properties of the arm were noticeable when ellipses were drawn at a fast speed. This study indicates that both biomechanical properties and central processes have an effect on the kinematics of continuous movements and particularly on the relation between speed and curvature. However, their relative importance varies with the type of figure and average movement speed. In conclusion, the results support the hypothesis that a time-consuming process of transformation of the intended direction of movement is operating during the production of continuous movements and that this process increases in speed between 8 to 12 years of age.

The gynecologic oncology fellowship interview process: Challenges and potential areas for improvement.

PubMed

Gressel, Gregory M; Van Arsdale, Anne; Dioun, Shayan M; Goldberg, Gary L; Nevadunsky, Nicole S

2017-05-01

The application and interview process for gynecologic oncology fellowship is highly competitive, time-consuming and expensive for applicants. We conducted a survey of successfully matched gynecologic oncology fellowship applicants to assess problems associated with the interview process and identify areas for improvement. All Society of Gynecologic Oncology (SGO) list-serve members who have participated in the match program for gynecologic oncology fellowship were asked to complete an online survey regarding the interview process. Linear regression modeling was used to examine association between year of match, number of programs applied to, cost incurred, and overall satisfaction. Two hundred and sixty-nine eligible participants reported applying to a mean of 20 programs [range 1-45] and were offered a mean of 14 interviews [range 1-43]. They spent an average of $6000 [$0-25,000], using personal savings (54%), credit cards (50%), family support (12%) or personal loans (3%). Seventy percent of respondents identified the match as fair, and 93% were satisfied. Interviewees spent a mean of 15 [0-45] days away from work and 37% reported difficulty arranging coverage. Linear regression showed an increase in number of programs applied to and cost per applicant over time ( p  < 0.001) between 1993 and 2016. Applicants who applied to all available programs spent more ( p  < 0.001) than those who applied to programs based on their location or quality. The current fellowship match was identified as fair and satisfying by most respondents despite being time consuming and expensive. Suggested alternative options included clustering interviews geographically or conducting preliminary interviews at the SGO Annual Meeting.

Generic-distributed framework for cloud services marketplace based on unified ontology.

PubMed

Hasan, Samer; Valli Kumari, V

2017-11-01

Cloud computing is a pattern for delivering ubiquitous and on demand computing resources based on pay-as-you-use financial model. Typically, cloud providers advertise cloud service descriptions in various formats on the Internet. On the other hand, cloud consumers use available search engines (Google and Yahoo) to explore cloud service descriptions and find the adequate service. Unfortunately, general purpose search engines are not designed to provide a small and complete set of results, which makes the process a big challenge. This paper presents a generic-distrusted framework for cloud services marketplace to automate cloud services discovery and selection process, and remove the barriers between service providers and consumers. Additionally, this work implements two instances of generic framework by adopting two different matching algorithms; namely dominant and recessive attributes algorithm borrowed from gene science and semantic similarity algorithm based on unified cloud service ontology. Finally, this paper presents unified cloud services ontology and models the real-life cloud services according to the proposed ontology. To the best of the authors' knowledge, this is the first attempt to build a cloud services marketplace where cloud providers and cloud consumers can trend cloud services as utilities. In comparison with existing work, semantic approach reduced the execution time by 20% and maintained the same values for all other parameters. On the other hand, dominant and recessive attributes approach reduced the execution time by 57% but showed lower value for recall.

Effects of gamma radiation on raspberries: safety and quality issues.

PubMed

Verde, S Cabo; Trigo, M J; Sousa, M B; Ferreira, A; Ramos, A C; Nunes, I; Junqueira, C; Melo, R; Santos, P M P; Botelho, M L

2013-01-01

There is an ever-increasing global demand from consumers for high-quality foods with major emphasis placed on quality and safety attributes. One of the main demands that consumers display is for minimally processed, high-nutrition/low-energy natural foods with no or minimal chemical preservatives. The nutritional value of raspberry fruit is widely recognized. In particular, red raspberries are known to demonstrate a strong antioxidant capacity that might prove beneficial to human health by preventing free radical-induced oxidative stress. However, food products that are consumed raw, are increasingly being recognized as important vehicles for transmission of human pathogens. Food irradiation is one of the few technologies that address both food quality and safety by virtue of its ability to control spoilage and foodborne pathogenic microorganisms without significantly affecting sensory or other organoleptic attributes of the food. Food irradiation is well established as a physical, nonthermal treatment (cold pasteurization) that processes foods at or nearly at ambient temperature in the final packaging, reducing the possibility of cross contamination until the food is actually used by the consumer. The aim of this study was to evaluate effects of gamma radiation on raspberries in order to assess consequences of irradiation. Freshly packed raspberries (Rubus idaeus L.) were irradiated in a (60)Co source at several doses (0.5, 1, or 1.5 kGy). Bioburden, total phenolic content, antioxidant activity, physicochemical properties such as texture, color, pH, soluble solids content, and acidity, and sensorial parameters were assessed before and after irradiation and during storage time up to 14 d at 4°C. Characterization of raspberries microbiota showed an average bioburden value of 10(4) colony-forming units (CFU)/g and a diverse microbial population predominantly composed of two morphological types (gram-negative, oxidase-negative rods, 35%, and filamentous fungi, 41%). The inactivation studies on the raspberries mesophilic population indicated a one log reduction of microbial load (95% inactivation efficiency for 1.5 kGy), in the surviving population mainly constituted by filamentous fungi (79-98%). The total phenolic content of raspberries indicated an increase with radiation doses and a decrease with storage time. The same trend was found for raspberries' antioxidant capacity with storage time. Regarding raspberries physicochemical properties, irradiation induced a significant decrease in firmness compared with nonirradiated fruit. However, nonirradiated and irradiated fruit presented similar physicochemical and sensory properties during storage time. Further studies are needed to elucidate the benefits of irradiation as a raspberries treatment process.

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

NASA Technical Reports Server (NTRS)

Goldman, H.; Wolf, M.

1979-01-01

The energy consumed in manufacturing silicon solar cell modules was calculated for the current process, as well as for 1982 and 1986 projected processes. In addition, energy payback times for the above three sequences are shown. The module manufacturing energy was partitioned two ways. In one way, the silicon reduction, silicon purification, sheet formation, cell fabrication, and encapsulation energies were found. In addition, the facility, equipment, processing material and direct material lost-in-process energies were appropriated in junction formation processes and full module manufacturing sequences. A brief methodology accounting for the energy of silicon wafers lost-in-processing during cell manufacturing is described.

Consumer evaluations of processed meat products reformulated to be healthier - A conjoint analysis study.

PubMed

Shan, Liran C; De Brún, Aoife; Henchion, Maeve; Li, Chenguang; Murrin, Celine; Wall, Patrick G; Monahan, Frank J

2017-09-01

Recent innovations in processed meats focus on healthier reformulations through reducing negative constituents and/or adding health beneficial ingredients. This study explored the influence of base meat product (ham, sausages, beef burger), salt and/or fat content (reduced or not), healthy ingredients (omega 3, vitamin E, none), and price (average or higher than average) on consumers' purchase intention and quality judgement of processed meats. A survey (n=481) using conjoint methodology and cluster analysis was conducted. Price and base meat product were most important for consumers' purchase intention, followed by healthy ingredient and salt and/or fat content. In reformulation, consumers had a preference for ham and sausages over beef burgers, and for reduced salt and/or fat over non reduction. In relation to healthy ingredients, omega 3 was preferred over none, and vitamin E was least preferred. Healthier reformulations improved the perceived healthiness of processed meats. Cluster analyses identified three consumer segments with different product preferences. Copyright © 2017 Elsevier Ltd. All rights reserved.

Traditional low-alcoholic and non-alcoholic fermented beverages consumed in European countries: a neglected food group.

PubMed

Baschali, Aristea; Tsakalidou, Effie; Kyriacou, Adamantini; Karavasiloglou, Nena; Matalas, Antonia-Leda

2017-06-01

Fermented beverages hold a long tradition and contribution to the nutrition of many societies and cultures worldwide. Traditional fermentation has been empirically developed in ancient times as a process of raw food preservation and at the same time production of new foods with different sensorial characteristics, such as texture, flavour and aroma, as well as nutritional value. Low-alcoholic fermented beverages (LAFB) and non-alcoholic fermented beverages (NAFB) represent a subgroup of fermented beverages that have received rather little attention by consumers and scientists alike, especially with regard to their types and traditional uses in European societies. A literature review was undertaken and research articles, review papers and textbooks were searched in order to retrieve data regarding the dietary role, nutrient composition, health benefits and other relevant aspects of diverse ethnic LAFB and NAFB consumed by European populations. A variety of traditional LAFB and NAFB consumed in European regions, such as kefir, kvass, kombucha and hardaliye, are presented. Milk-based LAFB and NAFB are also available on the market, often characterised as 'functional' foods on the basis of their probiotic culture content. Future research should focus on elucidating the dietary role and nutritional value of traditional and 'functional' LAFB and NAFB, their potential health benefits and consumption trends in European countries. Such data will allow for LAFB and NAFB to be included in national food composition tables.

Helping partnerships that facilitate recovery from severe mental illness.

PubMed

Anthony, Kathleen Hope

2008-07-01

The intent of this study was to learn how consumers experience helping partnerships that assist them in recovery to inform families, professionals, and peers about meaningful actions and strategies that promote the healing process. In-depth interviews were conducted with a purposeful sample of 10 individuals who had a self-reported diagnosis of severe mental illness. Using the phenomenological research process, helping partnerships and how they develop were described. Six key themes emerged from the data and included Networks of Helping Partnerships, Teaching-Learning, Spirituality, Creative Drive, Time, and Medication Adherence. Characteristics and behaviors of helping partners were identified, as well as structures that promoted their development. Educating the public, consumers, and mental health professionals about how to promote recovery, the role of spirituality and creativity, the benefits of medication and therapy, and the impact of learning on progressing through recovery can go a long way toward eliminating the mystery and fear associated with mental illness.

The service blueprint as a tool for designing innovative pharmaceutical services.

PubMed

Holdford, D A; Kennedy, D T

1999-01-01

To describe service blueprints, discuss their need and design, and provide examples of their use in advancing pharmaceutical care. Service blueprints are pictures or maps of service processes that permit the people involved in designing, providing, managing, and using the service to better understand them and deal with them objectively. A service blueprint simultaneously depicts the service process and the roles of consumers, service providers, and supporting services. Service blueprints can be useful in pharmacy because many of the obstacles to pharmaceutical care are a result of insufficient planning by service designers and/or poor communication between those designing services and those implementing them. One consequence of this poor design and communication is that many consumers and third party payers are uninformed about pharmacist roles. Service blueprints can be used by pharmacists to promote the value of pharmaceutical care to consumers and other decision makers. They can also assist in designing better pharmaceutical services. Blueprints are designed by identifying and mapping a process from the consumer's point of view, mapping employee actions and support activities, and adding visible evidence of service at each consumer action step. Key components of service blueprints are consumer actions, "onstage" and "backstage" employee actions, and support processes. Blueprints can help pharmacy managers identify and correct problems with the service process, provide pharmacy employees an opportunity to offer feedback in the planning stages of services, and demonstrate the value of pharmaceutical services to consumers. Service blueprints can be a valuable tool for designing, implementing, and evaluating pharmacy services.

Postreinforcement Pause in Grocery Shopping: Comparing Interpurchase Times across Products and Consumers

ERIC Educational Resources Information Center

Oliveira-Castro, Jorge M.; James, Victoria K.; Foxall, Gordon R.

2007-01-01

Purchase probability as a function of interpurchase time was examined through comparison of findings from laboratory experiments on reinforcement schedules and from marketing investigations of consumers' interpurchase time. Panel data, based on a sample of 80 consumers who purchased nine supermarket food products during 16 weeks, were used. For…

Improving quality of laser scanning data acquisition through calibrated amplitude and pulse deviation measurement

NASA Astrophysics Data System (ADS)

Pfennigbauer, Martin; Ullrich, Andreas

2010-04-01

Newest developments in laser scanner technologies put surveyors in the position to comply with the ever increasing demand of high-speed, high-accuracy, and highly reliable data acquisition from terrestrial, mobile, and airborne platforms. Echo digitization in pulsed time-of-flight laser ranging has demonstrated its superior performance in the field of bathymetry and airborne laser scanning for more than a decade, however at the cost of somewhat time consuming off line post processing. State-of-the-art online waveform processing as implemented in RIEGL's V-Line not only saves users post-processing time to obtain true 3D point clouds, it also adds the assets of calibrated amplitude and reflectance measurement for data classification and pulse deviation determination for effective and reliable data validation. We present results from data acquisitions in different complex target situations.

The Role of Virtual Reference in Library Web Site Design: A Qualitative Source for Usage Data

ERIC Educational Resources Information Center

Powers, Amanda Clay; Shedd, Julie; Hill, Clay

2011-01-01

Gathering qualitative information about usage behavior of library Web sites is a time-consuming process requiring the active participation of patron communities. Libraries that collect virtual reference transcripts, however, hold valuable data regarding how the library Web site is used that could benefit Web designers. An analysis of virtual…

Improving the Long-Term Care Referral Process: Insights from Patients and Caregivers

ERIC Educational Resources Information Center

Guihan, Marylou; Hedrick, Susan; Miller, Sara; Reder, Sheri

2011-01-01

Large increases in the need for long-term care (LTC) services are expected as baby boomers age. Little has been published about patient and caregiver preferences for information about LTC. However, our qualitative research findings suggest that potential consumers may find it difficult to obtain accurate and timely information about LTC programs…

Automatic Domain Adaptation of Word Sense Disambiguation Based on Sublanguage Semantic Schemata Applied to Clinical Narrative

ERIC Educational Resources Information Center

Patterson, Olga

2012-01-01

Domain adaptation of natural language processing systems is challenging because it requires human expertise. While manual effort is effective in creating a high quality knowledge base, it is expensive and time consuming. Clinical text adds another layer of complexity to the task due to privacy and confidentiality restrictions that hinder the…

A Requirements-Based Exploration of Open-Source Software Development Projects--Towards a Natural Language Processing Software Analysis Framework

ERIC Educational Resources Information Center

Vlas, Radu Eduard

2012-01-01

Open source projects do have requirements; they are, however, mostly informal, text descriptions found in requests, forums, and other correspondence. Understanding such requirements provides insight into the nature of open source projects. Unfortunately, manual analysis of natural language requirements is time-consuming, and for large projects,…

A Comparison of Web-Based Standard Setting and Monitored Standard Setting.

ERIC Educational Resources Information Center

Harvey, Anne L.; Way, Walter D.

Standard setting, when carefully done, can be an expensive and time-consuming process. The modified Angoff method and the benchmark method, as utilized in this study, employ representative panels of judges to provide recommended passing scores to standard setting decision-makers. It has been considered preferable to have the judges meet in a…

From Assessment to Annual Goal: Engaging a Decision-Making Process in Writing Measurable IEPs

ERIC Educational Resources Information Center

Capizzi, Andrea M.

2008-01-01

Despite federal regulations requiring measurable individualized education programs (IEPs), IEPs are often vague and unfocused, making them difficult to use in guiding instructional planning. Although a well-written IEP can be time consuming and labor intensive, a clearly written IEP, based on documented student needs, can and should be a guidepost…

The Polygonal Model: A Simple Representation of Biomolecules as a Tool for Teaching Metabolism

ERIC Educational Resources Information Center

Bonafe, Carlos Francisco Sampaio; Bispo, Jose Ailton Conceição; de Jesus, Marcelo Bispo

2018-01-01

Metabolism involves numerous reactions and organic compounds that the student must master to understand adequately the processes involved. Part of biochemical learning should include some knowledge of the structure of biomolecules, although the acquisition of such knowledge can be time-consuming and may require significant effort from the student.…

Contractor Past Performance Information (PPI) in Source Selection: A Comparison Study of Public and Private Sector

DTIC Science & Technology

2005-05-01

efficiencies similar to those in the private sector . However, along the way, Government and private sector industry have begun to disagree about how PPI is...double that of the private sector due to an evaluation process that is cumbersome, time-consuming, and lacking the efficiencies enjoyed by private

A hierarchical linear model for tree height prediction.

Treesearch

Vicente J. Monleon

2003-01-01

Measuring tree height is a time-consuming process. Often, tree diameter is measured and height is estimated from a published regression model. Trees used to develop these models are clustered into stands, but this structure is ignored and independence is assumed. In this study, hierarchical linear models that account explicitly for the clustered structure of the data...

Stripping Paint From Exterior Wood Surfaces

Treesearch

Mark T. Knaebe

2013-01-01

Removing paint and other film-forming finishes is a time consuming and often difficult process. In some cases, finishes need to be removed prior to repainting; for example, if the old surface is covered with severely peeled or blistered paint or if excessive paint buildup has caused cross-grain cracking. You must also remove the finish before applying a penetrating...

Word Learning in 6-Month-Olds: Fast Encoding-Weak Retention

ERIC Educational Resources Information Center

Friedrich, Manuela; Friederici, Angela D.

2011-01-01

There has been general consensus that initial word learning during early infancy is a slow and time-consuming process that requires very frequent exposure, whereas later in development, infants are able to quickly learn a novel word for a novel meaning. From the perspective of memory maturation, this shift in behavioral development might represent…

Activity Theory as a Framework for Designing the Model of College English Listening

ERIC Educational Resources Information Center

Zhang, Jianfeng

2014-01-01

Activity theory signifies that activities are at the centre of human behaviour and it has been used to study cognitive process in many fields. Nowadays, college English listening learning is time-consuming but less effective in China, so enhancing the performance of listening instruction is a very hot topic. Theoretically, activity theory is able…

Peer Assessment in the Classroom Using Mobile Devices

ERIC Educational Resources Information Center

Pellowe, William; Holster, Trevor; Lake, J.

2014-01-01

Peer feedback can engage the learning process, but collecting the survey data into a usable format can be time-consuming, which can deter classroom teachers from undertaking the kind of in-depth analysis for classroom research. To overcome this detriment, and in order to research the effects of learning by assessing, we created a peer feedback…

Development of an Imaging Fourier Transform Spectrometer

DTIC Science & Technology

1986-05-01

during multiple tests or concurrently applying many identical instrument systems to a single test. These difficult, expensive, and time-consuming...processes would introduce AEDC-TR-86-17 uncertainties due to nonstationary sources and instrument instability associated with multiple firings or... multiple instruments. For even moderate spatial, spectral, and temporal resolution, none of the previously mentioned approaches is reasonable. The

Consumer diversity across kingdoms supports multiple functions in a coastal ecosystem

PubMed Central

Hensel, Marc J. S.; Silliman, Brian R.

2013-01-01

The global biodiversity crisis impairs the valuable benefits ecosystems provide humans. These nature-generated benefits are defined by a multitude of different ecosystem functions that operate simultaneously. Although several studies have simulated species loss in communities and tracked the response of single functions such as productivity or nutrient cycling, these studies have involved relatively similar taxa, and seldom are strikingly different functions examined. With the exception of highly managed ecosystems such as agricultural fields, rarely are we interested in only one function being performed well. Instead, we rely on ecosystems to deliver several different functions at the same time. Here, we experimentally investigated the extinction impacts of dominant consumers in a salt marsh. These consumers are remarkably phylogenetically diverse, spanning two kingdoms (i.e., Animalia and Fungi). Our field studies reveal that a diverse consumer assemblage significantly enhances simultaneous functioning of disparate ecosystem processes (i.e., productivity, decomposition, and infiltration). Extreme functional and phylogenetic differences among consumers underlie this relationship. Each marsh consumer affected at least one different ecosystem function, and each individual function was affected by no more than two consumers. The implications of these findings are profound: If we want ecosystems to perform many different functions well, it is not just number of species that matter. Rather, the presence of species representing markedly different ecologies and biology is also essential to maximizing multiple functions. Moreover, this work emphasizes the need to incorporate both microcomponents and macrocomponents of food webs to accurately predict biodiversity declines on integrated-ecosystem functioning. PMID:24297926

Experimental calibration procedures for rotating Lorentz-force flowmeters

DOE PAGES

Hvasta, M. G.; Slighton, N. T.; Kolemen, E.; ...

2017-07-14

Rotating Lorentz-force flowmeters are a novel and useful technology with a range of applications in a variety of different industries. However, calibrating these flowmeters can be challenging, time-consuming, and expensive. In this paper, simple calibration procedures for rotating Lorentz-force flowmeters are presented. These procedures eliminate the need for expensive equipment, numerical modeling, redundant flowmeters, and system down-time. Finally, the calibration processes are explained in a step-by-step manner and compared to experimental results.

Experimental calibration procedures for rotating Lorentz-force flowmeters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hvasta, M. G.; Slighton, N. T.; Kolemen, E.

Rotating Lorentz-force flowmeters are a novel and useful technology with a range of applications in a variety of different industries. However, calibrating these flowmeters can be challenging, time-consuming, and expensive. In this paper, simple calibration procedures for rotating Lorentz-force flowmeters are presented. These procedures eliminate the need for expensive equipment, numerical modeling, redundant flowmeters, and system down-time. Finally, the calibration processes are explained in a step-by-step manner and compared to experimental results.

How important is vehicle safety for older consumers in the vehicle purchase process?

PubMed

Koppel, Sjaan; Clark, Belinda; Hoareau, Effie; Charlton, Judith L; Newstead, Stuart V

2013-01-01

This study aimed to investigate the importance of vehicle safety to older consumers in the vehicle purchase process. Older (n = 102), middle-aged (n = 791), and younger (n = 109) participants throughout the eastern Australian states of Victoria, New South Wales, and Queensland who had recently purchased a new or used vehicle completed an online questionnaire about their vehicle purchase process. When asked to list the 3 most important considerations in the vehicle purchase process (in an open-ended format), older consumers were mostly likely to list price as their most important consideration (43%). Similarly, when presented with a list of vehicle factors (such as price, design, Australasian New Car Assessment Program [ANCAP] rating), older consumers were most likely to identify price as the most important vehicle factor (36%). When presented with a list of vehicle features (such as automatic transmission, braking, air bags), older consumers in the current study were most likely to identify an antilock braking system (41%) as the most important vehicle feature, and 50 percent of older consumers identified a safety-related vehicle feature as the highest priority vehicle feature (50%). When asked to list up to 3 factors that make a vehicle safe, older consumers in the current study were most likely to list braking systems (35%), air bags (22%), and the driver's behavior or skill (11%). When asked about the influence of safety in the new vehicle purchase process, one third of older consumers reported that all new vehicles are safe (33%) and almost half of the older consumers rated their vehicle as safer than average (49%). A logistic regression model was developed to predict the profile of older consumers more likely to assign a higher priority to safety features in the vehicle purchasing process. The model predicted that the importance of safety-related features was influenced by several variables, including older consumers' beliefs that they could protect themselves and their family from a crash, their traffic infringement history, and whether they had children. These findings are consistent with previous research that suggests that, though older consumers highlight the importance of safety features (i.e., seat belts, air bags, braking), they often downplay the role of safety in their vehicle purchasing process and are more likely to equate vehicle safety with the presence of specific vehicle safety features or technologies rather than the vehicle's crash safety/test results or crashworthiness. The findings from this study provide a foundation to support further research in this area that can be used by policy makers, manufacturers, and other stakeholders to better target the promotion and publicity of vehicle safety features to particular consumer groups (such as older consumers). Better targeted campaigns may help to emphasize the value of safety features and their role in reducing the risk of injury/death. If older consumers are better informed of the benefits of safety features when purchasing a vehicle, a further reduction in injuries and deaths related to motor vehicle crashes may be realized.

Time-driven activity-based costing to identify opportunities for cost reduction in pediatric appendectomy.

PubMed

Yu, Yangyang R; Abbas, Paulette I; Smith, Carolyn M; Carberry, Kathleen E; Ren, Hui; Patel, Binita; Nuchtern, Jed G; Lopez, Monica E

2016-12-01

As reimbursement programs shift to value-based payment models emphasizing quality and efficient healthcare delivery, there exists a need to better understand process management to unearth true costs of patient care. We sought to identify cost-reduction opportunities in simple appendicitis management by applying a time-driven activity-based costing (TDABC) methodology to this high-volume surgical condition. Process maps were created using medical record time stamps. Labor capacity cost rates were calculated using national median physician salaries, weighted nurse-patient ratios, and hospital cost data. Consumable costs for supplies, pharmacy, laboratory, and food were derived from the hospital general ledger. Time-driven activity-based costing resulted in precise per-minute calculation of personnel costs. Highest costs were in the operating room ($747.07), hospital floor ($388.20), and emergency department ($296.21). Major contributors to length of stay were emergency department evaluation (270min), operating room availability (395min), and post-operative monitoring (1128min). The TDABC model led to $1712.16 in personnel costs and $1041.23 in consumable costs for a total appendicitis cost of $2753.39. Inefficiencies in healthcare delivery can be identified through TDABC. Triage-based standing delegation orders, advanced practice providers, and same day discharge protocols are proposed cost-reducing interventions to optimize value-based care for simple appendicitis. II. Copyright © 2016 Elsevier Inc. All rights reserved.

Accelerated pharmacokinetic map determination for dynamic contrast enhanced MRI using frequency-domain based Tofts model.

PubMed

Vajuvalli, Nithin N; Nayak, Krupa N; Geethanath, Sairam

2014-01-01

Dynamic Contrast Enhanced Magnetic Resonance Imaging (DCE-MRI) is widely used in the diagnosis of cancer and is also a promising tool for monitoring tumor response to treatment. The Tofts model has become a standard for the analysis of DCE-MRI. The process of curve fitting employed in the Tofts equation to obtain the pharmacokinetic (PK) parameters is time-consuming for high resolution scans. Current work demonstrates a frequency-domain approach applied to the standard Tofts equation to speed-up the process of curve-fitting in order to obtain the pharmacokinetic parameters. The results obtained show that using the frequency domain approach, the process of curve fitting is computationally more efficient compared to the time-domain approach.

Protein Folding Using a Vortex Fluidic Device.

PubMed

Britton, Joshua; Smith, Joshua N; Raston, Colin L; Weiss, Gregory A

2017-01-01

Essentially all biochemistry and most molecular biology experiments require recombinant proteins. However, large, hydrophobic proteins typically aggregate into insoluble and misfolded species, and are directed into inclusion bodies. Current techniques to fold proteins recovered from inclusion bodies rely on denaturation followed by dialysis or rapid dilution. Such approaches can be time consuming, wasteful, and inefficient. Here, we describe rapid protein folding using a vortex fluidic device (VFD). This process uses mechanical energy introduced into thin films to rapidly and efficiently fold proteins. With the VFD in continuous flow mode, large volumes of protein solution can be processed per day with 100-fold reductions in both folding times and buffer volumes.

Aspiration dynamics and the sustainability of resources in the public goods dilemma

NASA Astrophysics Data System (ADS)

Du, Jinming; Wu, Bin; Wang, Long

2016-04-01

How to exploit public non-renewable resources is a public goods dilemma. Individuals can choose to limit the depletion in order to use the resource for a longer time or consume more goods to benefit themselves. When the resource is used up, there is no benefit for the future generations any more, thus the evolutionary process ends. Here we investigate what mechanisms can extend the use of resources in the framework of evolutionary game theory under two updating rules based on imitation and aspiration, respectively. Compared with imitation process, aspiration dynamics may prolong the sustainable time of a public resource.

Applying Semantics in Dataset Summarization for Solar Data Ingest Pipelines

NASA Astrophysics Data System (ADS)

Michaelis, J.; McGuinness, D. L.; Zednik, S.; West, P.; Fox, P. A.

2012-12-01

One goal in studying phenomena of the solar corona (e.g., flares, coronal mass ejections) is to create and refine predictive models of space weather - which have broad implications for terrestrial activity (e.g., communication grid reliability). The High Altitude Observatory (HAO) [1] presently maintains an infrastructure for generating time-series visualizations of the solar corona. Through raw data gathered at the Mauna Loa Solar Observatory (MLSO) in Hawaii, HAO performs follow-up processing and quality control steps to derive visualization sets consumable by scientists. Individual visualizations will acquire several properties during their derivation, including: (i) the source instrument at MLSO used to obtain the raw data, (ii) the time the data was gathered, (iii) processing steps applied by HAO to generate the visualization, and (iv) quality metrics applied over both the raw and processed data. In parallel to MLSO's standard data gathering, time stamped observation logs are maintained by MLSO staff, which covers content of potential relevance to data gathered (such as local weather and instrument conditions). In this setting, while a significant amount of solar data is gathered, only small sections will typically be of interest to consuming parties. Additionally, direct presentation of solar data collections could overwhelm consumers (particularly those with limited background in the data structuring). This work explores how multidimensional analysis based navigation can be used to generate summary views of data collections, based on two operations: (i) grouping visualization entries based on similarity metrics (e.g., data gathered between 23:15-23:30 6-21-2012), or (ii) filtering entries (e.g., data with a quality score of UGLY, on a scale of GOOD, BAD, or UGLY). Here, semantic encodings of solar visualization collections (based on the Resource Description Framework (RDF) Datacube vocabulary [2]) are being utilized, based on the flexibility of the RDF model for supporting the following use cases: (i) Temporal alignment of time-stamped MLSO observations with raw data gathered at MLSO. (ii) Linking of multiple visualization entries to common (and structurally complex) workflow structures - designed to capture the visualization generation process. To provide real-world use cases for the described approach, a semantic summarization system is being developed for data gathered from HAO's Coronal Multi-channel Polarimeter (CoMP) and Chromospheric Helium-I Imaging Photometer (CHIP) pipelines. Web Links: [1] http://mlso.hao.ucar.edu/ [2] http://www.w3.org/TR/vocab-data-cube/

Design and implementation of Bluetooth beacon in mobile payment system

NASA Astrophysics Data System (ADS)

Han, Tiantian; Ding, Lei

2017-08-01

The current line of payment means, mainly in the following ways, cash payment, credit card payment, WeChat Alipay sweep payment. There are many inconvenience in Cash payment, large amounts of cash inconvenience to carry, count the money to spend time and effort, true and false banknotes difficult to distinguish, ticket settlement easy to go wrong. Credit card payment is relatively time-consuming, and WeChat Alipay sweep payment need to sweep. Therefore, the design of a convenient, fast payment to meet the line to pay the demand is particularly important. Based on the characteristics of BLE Bluetooth wireless communication technology, this paper designs a kind of payment method based on Bluetooth beacon. Through the Bluetooth beacon broadcast consumption, consumers only need to open the relevant APP in the Android client, and you can get Bluetooth via mobile phone Bluetooth the amount of consumption of the standard broadcast, in accordance with the corresponding payment platform to complete the payment process, which pay less time to improve the efficiency of payment.

Evolution of the Interstellar Gas Fraction Over Cosmic Time

NASA Astrophysics Data System (ADS)

Wiklind, Tommy; CANDELS

2018-01-01

Galaxies evolve by transforming gas into stars. The gas is acquired through accretion and mergers and is a highly intricate process where feed-back processes play an important role. Directly measuring the gas content in distant galaxies is, however, both complicated and time consuming. A direct observations involves either observing neutral hydrogen using the 21cm line or observing the molecular gas component using tracer molecules such as CO. The former method is impeded by man-made radio interference, and the latter is time consuming even with sensitive instruments such s ALMA. An indirect method is to observe the Raleigh-Jeans part of the dust SED and from this infer the gas mass. Here we present the results from a project using ALMA to measure the RJ part of the dust SED in a carefully selected sample of 70 galaxies at redshifts z=2-5. The galaxies are selected solely based on their redshift and stellar mass and therefore represents an unbiased sample. The stellar masses are selected using the MEAM method and thus the sample corresponds to progenitors of a z=0 galaxy of a particular stellar mass. Preliminary results show that the average gas fraction increases with redshift over the range z=2-3 in accordance with theoretical models, but at z≥4 the observed gas fraction is lower.

What criteria do consumer health librarians use to develop library collections? a phenomenological study.

PubMed

Papadakos, Janet; Trang, Aileen; Wiljer, David; Cipolat Mis, Chiara; Cyr, Alaina; Friedman, Audrey Jusko; Mazzocut, Mauro; Snow, Michelle; Raivich, Valeria; Catton, Pamela

2014-04-01

The criteria for determining whether resources are included in consumer health library collections are summarized in institutional collection development policies (CDPs). Evidence suggests that CDPs do not adequately capture all of these criteria. The aim of this study was to describe the resource review experience of librarians and compare it to what is described in CDPs. A phenomenological approach was used to explore and describe the process. Four consumer health librarians independently evaluated cancer-related consumer health resources and described their review process during a semi-structured telephone interview. Afterward, these librarians completed online questionnaires about their approaches to collection development. CDPs from participating libraries, interview transcripts, and questionnaire data were analyzed. Researchers summarized the findings, and participating librarians reviewed results for validation. Librarians all utilized similar criteria, as documented in their CDPs; however, of thirteen criteria described in the study, only four were documented in CDPs. CDPs for consumer health libraries may be missing important criteria that are considered integral parts of the collection development process. A better understanding of the criteria and contextual factors involved in the collection development process can assist with establishing high-quality consumer health library collections.

What criteria do consumer health librarians use to develop library collections? a phenomenological study*

PubMed Central

Papadakos, Janet; Trang, Aileen; Wiljer, David; Mis, Chiara Cipolat; Cyr, Alaina; Friedman, Audrey Jusko; Mazzocut, Mauro; Snow, Michelle; Raivich, Valeria; Catton, Pamela

2014-01-01

Objectives: The criteria for determining whether resources are included in consumer health library collections are summarized in institutional collection development policies (CDPs). Evidence suggests that CDPs do not adequately capture all of these criteria. The aim of this study was to describe the resource review experience of librarians and compare it to what is described in CDPs. Methods: A phenomenological approach was used to explore and describe the process. Four consumer health librarians independently evaluated cancer-related consumer health resources and described their review process during a semi-structured telephone interview. Afterward, these librarians completed online questionnaires about their approaches to collection development. CDPs from participating libraries, interview transcripts, and questionnaire data were analyzed. Researchers summarized the findings, and participating librarians reviewed results for validation. Results: Librarians all utilized similar criteria, as documented in their CDPs; however, of thirteen criteria described in the study, only four were documented in CDPs. Conclusions: CDPs for consumer health libraries may be missing important criteria that are considered integral parts of the collection development process. Implications: A better understanding of the criteria and contextual factors involved in the collection development process can assist with establishing high-quality consumer health library collections. PMID:24860261

A Longitudinal Study of Consumer Socialization.

ERIC Educational Resources Information Center

Moschis, George P.; Moore, Roy L.

A study examined the effects of factors (including television, family, peers, age, and socioeconomic status) on consumer socialization, the process by which individuals develop consumption-related cognitions and behaviors. The specific criterion variables studied included consumer affairs knowledge, puffery filtering, consumer finance management,…

Effective dose in SMAW and FCAW welding processes using rutile consumables.

PubMed

Herranz, M; Rozas, S; Idoeta, R; Alegría, N

2014-03-01

The shielded metal arc welding (SMAW) and flux cored arc welding (FCAW) processes use covered electrodes and flux cored wire as consumables. Among these consumables, ones containing rutile are the most widely used, and since they have a considerable natural radioactive content, they can be considered as NORM (naturally occurring radioactive material). To calculate the effective dose on workers during their use in a conservative situation, samples of slag and aerosols and particles emitted or deposited during welding were taken and measured by gamma, alpha and beta spectrometry. An analytical method was also developed for estimating the activity concentration of radionuclides in the inhaled air. (222)Rn activity concentration was also assessed. With all these data, internal and external doses were calculated. The results show that external doses are negligible in comparison with internal ones, which do not exceed 1 mSv yr(-1), either in this conservative situation or in any other more favourable one. Radionuclides after Rn in the radioactive natural series are emitted at the same activity concentration to the atmosphere, this being around 17 times higher than that corresponding to radionuclides before Rn. Taking into account these conclusions and the analytical method developed, it can be concluded that one way to assess the activity concentration of natural radionuclides in inhaled air and hence effective doses could be the early gamma-ray spectrometry of aerosols and particles sampled during the welding process.

Increased consumer density reduces the strength of neighborhood effects in a model system.

PubMed

Merwin, Andrew C; Underwood, Nora; Inouye, Brian D

2017-11-01

An individual's susceptibility to attack can be influenced by conspecific and heterospecifics neighbors. Predicting how these neighborhood effects contribute to population-level processes such as competition and evolution requires an understanding of how the strength of neighborhood effects is modified by changes in the abundances of both consumers and neighboring resource species. We show for the first time that consumer density can interact with the density and frequency of neighboring organisms to determine the magnitude of neighborhood effects. We used the bean beetle, Callosobruchus maculatus, and two of its host beans, Vigna unguiculata and V. radiata, to perform a response-surface experiment with a range of resource densities and three consumer densities. At low beetle density, damage to beans was reduced with increasing conspecific density (i.e., resource dilution) and damage to the less preferred host, V. unguiculata, was reduced with increasing V. radiata frequency (i.e., frequency-dependent associational resistance). As beetle density increased, however, neighborhood effects were reduced; at the highest beetle densities neither focal nor neighboring resource density nor frequency influenced damage. These findings illustrate the importance of consumer density in mediating indirect effects among resources, and suggest that accounting for consumer density may improve our ability to predict population-level outcomes of neighborhood effects and our use of them in applications such as mixed-crop pest management. © 2017 by the Ecological Society of America.

The influence of ultra-pasteurization by indirect heating versus direct steam injection on skim and 2% fat milks.

PubMed

Lee, A P; Barbano, D M; Drake, M A

2017-03-01

Fluid milk is traditionally pasteurized by high temperature, short time (HTST) pasteurization, which requires heating to at least 72°C for 15 s. Ultra-pasteurization (UP) extends milk shelf life and is defined as heating to at least 138°C for 2 s. The UP process can be done by indirect heating (IND) or by direct steam injection (DSI). The influence of these 2 UP methods on milk flavor has not been widely investigated. The objective of this study was to compare the effect of HTST, IND-UP, and DSI-UP on sensory perception of fluid milk. Raw skim and standardized 2% milks were pasteurized at 140°C for 2.3 s by IND or DSI or by HTST (78°C, 15 s) and homogenized at 20.7 MPa. The processed milks were stored in light-shielded opaque high-density polyethylene containers at 4°C and examined by descriptive analysis and microbial analysis on d 3, 7, and 14. Furosine and serum protein denaturation analyses were performed on d 0 and 14 as an indicator of heat treatment. Last, consumer acceptance testing was conducted at d 10, with adults (n = 250) and children (ages 8 to13 y, n = 100) who were self-reported consumers of skim or 2% milk; consumers only received samples for either skim or 2% milk. The entire experiment was repeated in triplicate. Milks treated by HTST had lower cooked flavor than either UP milk. Milks heated by DSI-UP were characterized by sulfur or eggy and cooked flavors, whereas IND-UP milks had higher sweet aromatic and sweet taste compared with DSI-UP milk. Aromatic flavor intensities of all milks decreased across 14 d of storage. Furosine concentrations and serum protein denaturation were highest for the IND treatments, followed by DSI and HTST. Furosine content in both skim and 2% milk increased with time, but the increase was faster in IND-UP skim milk. Adult and child consumers preferred HTST milk over either UP milk, regardless of fat content. Ultra-pasteurization by IND or DSI did not affect consumer acceptance at 10 d postprocessing, but traditional HTST milks were preferred by consumers of all ages. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

A GIS-based hedonic price model for agricultural land

NASA Astrophysics Data System (ADS)

Demetriou, Demetris

2015-06-01

Land consolidation is a very effective land management planning approach that aims towards rural/agricultural sustainable development. Land reallocation which involves land tenure restructuring is the most important, complex and time consuming component of land consolidation. Land reallocation relies on land valuation since its fundamental principle provides that after consolidation, each landowner shall be granted a property of an aggregate value that is approximately the same as the value of the property owned prior to consolidation. Therefore, land value is the crucial factor for the land reallocation process and hence for the success and acceptance of the final land consolidation plan. Land valuation is a process of assigning values to all parcels (and its contents) and it is usually carried out by an ad-hoc committee. However, the process faces some problems such as it is time consuming hence costly, outcomes may present inconsistency since it is carried out manually and empirically without employing systematic analytical tools and in particular spatial analysis tools and techniques such as statistical/mathematical. A solution to these problems can be the employment of mass appraisal land valuation methods using automated valuation models (AVM) based on international standards. In this context, this paper presents a spatial based linear hedonic price model which has been developed and tested in a case study land consolidation area in Cyprus. Results showed that the AVM is capable to produce acceptable in terms of accuracy and reliability land values and to reduce time hence cost required by around 80%.

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2010 CFR

2010-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... the lease contract, so long as all disclosures are given at the same time. Alternatively, all...

12 CFR Supplement I to Part 213 - Official Staff Commentary to Regulation M

Code of Federal Regulations, 2011 CFR

2011-01-01

... primary use. 2. Period of time. To be a consumer lease, the initial term of the lease must be more than... lease (unless terminable without penalty at any time by the consumer) under which the consumer: i... the lease contract, so long as all disclosures are given at the same time. Alternatively, all...

Time trends and patterns of reported egg consumption in the U.S. by sociodemographic characteristics

USDA-ARS?s Scientific Manuscript database

Objectives: To 1) describe time trends of the percentage of individuals in the U.S that consume eggs, 2) describe time trends of the daily amount of eggs consumed per day, and 3) examine differences in the amount of eggs consumed per day; overall and by gender, age, income, education, race-ethnicit...

Patterning of Indium Tin Oxide Films

NASA Technical Reports Server (NTRS)

Immer, Christopher

2008-01-01

A relatively rapid, economical process has been devised for patterning a thin film of indium tin oxide (ITO) that has been deposited on a polyester film. ITO is a transparent, electrically conductive substance made from a mixture of indium oxide and tin oxide that is commonly used in touch panels, liquid-crystal and plasma display devices, gas sensors, and solar photovoltaic panels. In a typical application, the ITO film must be patterned to form electrodes, current collectors, and the like. Heretofore it has been common practice to pattern an ITO film by means of either a laser ablation process or a photolithography/etching process. The laser ablation process includes the use of expensive equipment to precisely position and focus a laser. The photolithography/etching process is time-consuming. The present process is a variant of the direct toner process an inexpensive but often highly effective process for patterning conductors for printed circuits. Relative to a conventional photolithography/ etching process, this process is simpler, takes less time, and is less expensive. This process involves equipment that costs less than $500 (at 2005 prices) and enables patterning of an ITO film in a process time of less than about a half hour.

Optimizing ELISAs for precision and robustness using laboratory automation and statistical design of experiments.

PubMed

Joelsson, Daniel; Moravec, Phil; Troutman, Matthew; Pigeon, Joseph; DePhillips, Pete

2008-08-20

Transferring manual ELISAs to automated platforms requires optimizing the assays for each particular robotic platform. These optimization experiments are often time consuming and difficult to perform using a traditional one-factor-at-a-time strategy. In this manuscript we describe the development of an automated process using statistical design of experiments (DOE) to quickly optimize immunoassays for precision and robustness on the Tecan EVO liquid handler. By using fractional factorials and a split-plot design, five incubation time variables and four reagent concentration variables can be optimized in a short period of time.

Simulation of Propellant Loading System Senior Design Implement in Computer Algorithm

NASA Technical Reports Server (NTRS)

Bandyopadhyay, Alak

2010-01-01

Propellant loading from the Storage Tank to the External Tank is one of the very important and time consuming pre-launch ground operations for the launch vehicle. The propellant loading system is a complex integrated system involving many physical components such as the storage tank filled with cryogenic fluid at a very low temperature, the long pipe line connecting the storage tank with the external tank, the external tank along with the flare stack, and vent systems for releasing the excess fuel. Some of the very important parameters useful for design purpose are the prediction of pre-chill time, loading time, amount of fuel lost, the maximum pressure rise etc. The physics involved for mathematical modeling is quite complex due to the fact the process is unsteady, there is phase change as some of the fuel changes from liquid to gas state, then conjugate heat transfer in the pipe walls as well as between solid-to-fluid region. The simulation is very tedious and time consuming too. So overall, this is a complex system and the objective of the work is student's involvement and work in the parametric study and optimization of numerical modeling towards the design of such system. The students have to first become familiar and understand the physical process, the related mathematics and the numerical algorithm. The work involves exploring (i) improved algorithm to make the transient simulation computationally effective (reduced CPU time) and (ii) Parametric study to evaluate design parameters by changing the operational conditions

Consumer acceptance of irradiated food: theory and reality

NASA Astrophysics Data System (ADS)

Bruhn, Christine M.

1998-06-01

For years most consumers have expressed less concern about food irradiation than other food processing technologies. Attitude studies have demonstrated that when given science-based information, from 60% to 90% of consumers prefer the advantages irradiation processing provides. When information is accompanied by samples, acceptance may increase to 99%. Information on irradiation should include product benefits, safety and wholesomeness, address environmental safety issues, and include endorsements by recognized health authorities. Educational and marketing programs should now be directed toward retailers and processors. Given the opportunity, consumers will buy high quality, safety-enhanced irradiated food.

Aging and consumer decision making

PubMed Central

Carpenter, Stephanie M.; Yoon, Carolyn

2013-01-01

Research on consumer decision making and aging is especially important for fostering a better understanding of ways to maintain consumer satisfaction and high decision quality across the life span. We provide a review of extant research on the effects of normal aging on cognition and decision processes and how these age-related processes are influenced by task environment, meaningfulness of the task, and consumer expertise. We consider how research centered on these topics generates insights about changes in consumption decisions that occur with aging and identify a number of gaps and directions for future research. PMID:22360794

[Consumer involvement in the Disease Management Guideline for Asthma--a background report].

PubMed

Senger, Sylvia; Lelgemann, Monika; Kopp, Ina

2006-01-01

In the past clinical guidelines were mainly developed by experts and in everyday clinical practice almost exclusively used by clinical experts, while issues that were relevant from the patients' (consumers') point of view tended to be neglected. But then, the majority of patient information has not been perceptibly connected to clinical guidelines. Connecting the development of clinical guidelines with the development of patient information publications would make good sense for both products, though. On the one hand, evidence-based treatment guidelines could be made available to the actual target group of the clinical care process--i.e. the patients or consumers--and on the other hand, patient experiences and competencies (social evidence) might inform the production of guidelines. Such a procedure demands the cooperation of clinical experts and patients. So far there are no generally accepted methods in Germany for the practical implementation of consumer involvement on both the organizational and content level with the aim of involving patients in the development process of guidelines as well as the production of the respective patient information versions. Such a methodology shall be established as part of the National Program for Disease Management Guidelines. For the first time in this program, patient involvement is being exercised within the scope of the National Disease Management Guideline for Asthma (NDM Asthma). Here, patients are involved in the NDM development process by providing the opportunity to comment on the consented guideline draft and to participate in the translation of the NDM Asthma into a patient version. The present paper is a background report describing the current state of work and indicating consequences for some future developments.

Ultra-Rapid serial visual presentation reveals dynamics of feedforward and feedback processes in the ventral visual pathway.

PubMed

Mohsenzadeh, Yalda; Qin, Sheng; Cichy, Radoslaw M; Pantazis, Dimitrios

2018-06-21

Human visual recognition activates a dense network of overlapping feedforward and recurrent neuronal processes, making it hard to disentangle processing in the feedforward from the feedback direction. Here, we used ultra-rapid serial visual presentation to suppress sustained activity that blurs the boundaries of processing steps, enabling us to resolve two distinct stages of processing with MEG multivariate pattern classification. The first processing stage was the rapid activation cascade of the bottom-up sweep, which terminated early as visual stimuli were presented at progressively faster rates. The second stage was the emergence of categorical information with peak latency that shifted later in time with progressively faster stimulus presentations, indexing time-consuming recurrent processing. Using MEG-fMRI fusion with representational similarity, we localized recurrent signals in early visual cortex. Together, our findings segregated an initial bottom-up sweep from subsequent feedback processing, and revealed the neural signature of increased recurrent processing demands for challenging viewing conditions. © 2018, Mohsenzadeh et al.

Realia: Tools for Consumer Education Instruction

ERIC Educational Resources Information Center

Green, D. Hayden

1974-01-01

These suggestions on using realia in the classroom should augment carefully conceived strategies for teaching concepts concerning the consumer in the economy, the consumer in the marketplace, and the consumer's decision-making processes. Realia can bridge the gap between abstract subject matter and functional applications. (BP)

Contributions of Socialization Theory to Consumer Behavior Research

ERIC Educational Resources Information Center

Ward, Scott

1978-01-01

Socialization theory can contribute to consumer research because it focuses on (1) youth and development, (2) interaction of factors affecting consumer behavior, and (3) linkages between mental processes and overt behavior. Various approaches to socialization research and consumer research are described, including cognitive development and…

Community and consumer participation in Australian health services--an overview of organisational commitment and participation processes.

PubMed

Johnson, A; Silburn, K

2000-01-01

This article briefly describes recent initiatives to improve consumer participation in health services that have led to the establishment of the National Resource Centre for Consumer Participation in Health. The results of a component of the needs assessment undertaken by the newly established Centre are presented. They provide a 'snapshot' of the types of feedback and participation processes mainly being utilised by Australian health services at the different levels of seeking information, information sharing and consultation, partnership, delegated power and consumer control. They also allow identification of the organisational commitment made by Australian health services to support a more coordinated approach to community and consumer feedback and participation at different levels of health services such as particular emphasis on determining the presence of community and consumer participation in key organisational statements, specific consumer policies and plans, identifiable leadership, inclusion into job descriptions, allocation of resources, and staff development and consumer training. Discussion centres around four key observations and some of the key perceived external barriers.

A longitudinal model of the dynamics between HMOs' consumer-friendliness and preventive health care utilization.

PubMed

Xiao, Qian; Savage, Grant T; Zhuang, Weiling

2014-01-01

This study aims at replicating and extending Xiao and Savage's (2008) research to understand the multidimensional aspect of HMOs distinguished by HMOs' consumer-friendliness, and their relationship to consumers' preventive care utilization. This study develops a dynamic model to consider both concurrent and time lagging effects of HMOs' consumer-friendliness. Our data analysis discloses similar relationship patterns as revealed by Xiao and Savage. Additionally, our findings reveal the time-series changes of the influence of HMOs' consumer-friendliness that either the effects of early experienced HMOs' consumer-friendliness wear out totally or HMOs' consumer-friendly characteristics on the concurrent term contain most of the explanatory power.

Improving delivery routes using combined heuristic and optimization in a consumer goods distribution company

NASA Astrophysics Data System (ADS)

Wibisono, E.; Santoso, A.; Sunaryo, M. A.

2017-11-01

XYZ is a distributor of various consumer goods products. The company plans its delivery routes daily and in order to obtain route construction in a short amount of time, it simplifies the process by assigning drivers based on geographic regions. This approach results in inefficient use of vehicles leading to imbalance workloads. In this paper, we propose a combined method involving heuristic and optimization to obtain better solutions in acceptable computation time. The heuristic is based on a time-oriented, nearest neighbor (TONN) to form clusters if the number of locations is higher than a certain value. The optimization part uses a mathematical modeling formulation based on vehicle routing problem that considers heterogeneous vehicles, time windows, and fixed costs (HVRPTWF) and is used to solve routing problem in clusters. A case study using data from one month of the company’s operations is analyzed, and data from one day of operations are detailed in this paper. The analysis shows that the proposed method results in 24% cost savings on that month, but it can be as high as 54% in a day.

Mere exposure and the endowment effect on consumer decision making.

PubMed

Tom, Gail; Nelson, Carolyn; Srzentic, Tamara; King, Ryan

2007-03-01

Previous researchers (e.g., J. A. Bargh, 1992, 2002) demonstrated the importance of nonconscious processes on consumer choice behavior. Using an advertisement, the authors determined the effect of two nonconscious processes--the mere exposure effect, which increases object preference by increasing consumer exposure to an object, and the endowment effect, which increases object valuation by providing consumer possession of an object--on consumer behavior. Although the mere exposure effect and endowment effect did not produce an interaction, they produced independent effects. The endowment effect increased object valuation but not object preference. The mere exposure effect increased object preference but not object valuation. Thus, at the unconscious level, an increase in object preference does not lead to an increase in object valuation, nor does an increase in object valuation lead to an increase in object preference. The authors discuss the importance of developing measures of unconscious process in advertising effectiveness.

Weighting Statistical Inputs for Data Used to Support Effective Decision Making During Severe Emergency Weather and Environmental Events

NASA Technical Reports Server (NTRS)

Gardner, Adrian

2010-01-01

National Aeronautical and Space Administration (NASA) weather and atmospheric environmental organizations are insatiable consumers of geophysical, hydrometeorological and solar weather statistics. The expanding array of internet-worked sensors producing targeted physical measurements has generated an almost factorial explosion of near real-time inputs to topical statistical datasets. Normalizing and value-based parsing of such statistical datasets in support of time-constrained weather and environmental alerts and warnings is essential, even with dedicated high-performance computational capabilities. What are the optimal indicators for advanced decision making? How do we recognize the line between sufficient statistical sampling and excessive, mission destructive sampling ? How do we assure that the normalization and parsing process, when interpolated through numerical models, yields accurate and actionable alerts and warnings? This presentation will address the integrated means and methods to achieve desired outputs for NASA and consumers of its data.

Gene trap and gene inversion methods for conditional gene inactivation in the mouse

PubMed Central

Xin, Hong-Bo; Deng, Ke-Yu; Shui, Bo; Qu, Shimian; Sun, Qi; Lee, Jane; Greene, Kai Su; Wilson, Jason; Yu, Ying; Feldman, Morris; Kotlikoff, Michael I.

2005-01-01

Conditional inactivation of individual genes in mice using site-specific recombinases is an extremely powerful method for determining the complex roles of mammalian genes in developmental and tissue-specific contexts, a major goal of post-genomic research. However, the process of generating mice with recombinase recognition sequences placed at specific locations within a gene, while maintaining a functional allele, is time consuming, expensive and technically challenging. We describe a system that combines gene trap and site-specific DNA inversion to generate mouse embryonic stem (ES) cell clones for the rapid production of conditional knockout mice, and the use of this system in an initial gene trap screen. Gene trapping should allow the selection of thousands of ES cell clones with defined insertions that can be used to generate conditional knockout mice, thereby providing extensive parallelism that eliminates the time-consuming steps of targeting vector construction and homologous recombination for each gene. PMID:15659575

A multidirectional communication model: implications for social marketing practice.

PubMed

Thackeray, Rosemary; Neiger, Brad L

2009-04-01

The landscape of sending and receiving information has changed dramatically in the past 25 years. The communication process is changing from being unidirectional to multidirectional as consumers are becoming active participants by creating, seeking, and sharing information using a variety of channels and devices. The purpose of this article is to describe how this shift in the communication process- where gatekeepers control the creation and content of information and consumers are less active recipients to one that reflects a multidirectional and more dynamic process with participative consumers-will affect the social marketing process. This shift in communication does not represent an option for social marketers so much as a necessity. As professionals respond to this evolving communication model, the practice of social marketing can remain vibrant as a relevant consumer-oriented approach to behavior change.

Real-time volume rendering of 4D image using 3D texture mapping

NASA Astrophysics Data System (ADS)

Hwang, Jinwoo; Kim, June-Sic; Kim, Jae Seok; Kim, In Young; Kim, Sun Il

2001-05-01

Four dimensional image is 3D volume data that varies with time. It is used to express deforming or moving object in virtual surgery of 4D ultrasound. It is difficult to render 4D image by conventional ray-casting or shear-warp factorization methods because of their time-consuming rendering time or pre-processing stage whenever the volume data are changed. Even 3D texture mapping is used, repeated volume loading is also time-consuming in 4D image rendering. In this study, we propose a method to reduce data loading time using coherence between currently loaded volume and previously loaded volume in order to achieve real time rendering based on 3D texture mapping. Volume data are divided into small bricks and each brick being loaded is tested for similarity to one which was already loaded in memory. If the brick passed the test, it is defined as 3D texture by OpenGL functions. Later, the texture slices of the brick are mapped into polygons and blended by OpenGL blending functions. All bricks undergo this test. Continuously deforming fifty volumes are rendered in interactive time with SGI ONYX. Real-time volume rendering based on 3D texture mapping is currently available on PC.

RFID in Space: Exploring the Feasibility and Performance of Gen 2 Tags as a Means of Tracking Equipment, Supplies, and Consumable Products in Cargo Transport Bags onboard a Space Vehicle or Habitat

NASA Technical Reports Server (NTRS)

Jones, Erick C.; Richards, Casey; Herstein, Kelli; Franca, Rodrigo; Yagoda, Evan L.; Vasquez, Reuben

2008-01-01

Current inventory management techniques for consumables and supplies aboard space vehicles are burdensome and time consuming. Inventory of food, clothing, and supplies are taken periodically by manually scanning the barcodes on each item. The inaccuracy of reading barcodes and the excessive amount of time it takes for the astronauts to perform this function would be better spent doing scientific experiments. Therefore, there is a need for an alternative method of inventory control by NASA astronauts. Radio Frequency Identification (RFID) is an automatic data capture technology that has potential to create a more effective and user-friendly inventory management system (IMS). In this paper we introduce a Design for Six Sigma Research (DFSS-R) methodology that allows for reliability testing of RFID systems. The research methodology uses a modified sequential design of experiments process to test and evaluate the quality of commercially available RFID technology. The results from the experimentation are compared to the requirements provided by NASA to evaluate the feasibility of using passive Generation 2 RFID technology to improve inventory control aboard crew exploration vehicles.

Consumer Participation in Co-creation: An Enlightening Model of Causes and Effects Based on Ethical Values and Transcendent Motives.

PubMed

Martínez-Cañas, Ricardo; Ruiz-Palomino, Pablo; Linuesa-Langreo, Jorge; Blázquez-Resino, Juan J

2016-01-01

In the current highly interconnected modern world, the role of consumers has changed substantially due to their active collaboration with companies in product and process innovation. Specifically, consumer participation has become key to the development of successful products and services, as companies have come to rely more and more on consumers' opinion as a source of innovative ideas and brand value. However, whereas existing research has focused on identifying the different elements involved in consumers' co-creation, there is still the need to comprehend better this complex mechanism by integrating distinct dimensional insights. With an integrative review of research into three important perspectives, one nurturing from the Service-Dominant logic, another one based on the information and communication technologies (ICTs) platforms, and (the ethical values-driven) Marketing 3.0 paradigm, this article proposes a conceptual framework in which consumers' ethical values and transcendent motivations play an important role in encouraging their engagement in co-creation activities. In this connection, and with consumers increasingly embracing the need to fulfill a social and ethical function in society, the co-creation process is here comprehended as a means to emphasize the social and moral aspects of co-creation. This article also identifies the important, supportive role of the Marketing 3.0 paradigm and Web 3.0 tools to initiate the co-creation process, as well as the important valuable benefits attained by both companies and consumers after consumers engage in this process. Importantly, these benefits are highlighted to increase when ethical products are the object of these co-creation activities. All these insights have notable implications for both research and managerial practice.

Consumer Participation in Co-creation: An Enlightening Model of Causes and Effects Based on Ethical Values and Transcendent Motives

PubMed Central

Martínez-Cañas, Ricardo; Ruiz-Palomino, Pablo; Linuesa-Langreo, Jorge; Blázquez-Resino, Juan J.

2016-01-01

In the current highly interconnected modern world, the role of consumers has changed substantially due to their active collaboration with companies in product and process innovation. Specifically, consumer participation has become key to the development of successful products and services, as companies have come to rely more and more on consumers' opinion as a source of innovative ideas and brand value. However, whereas existing research has focused on identifying the different elements involved in consumers' co-creation, there is still the need to comprehend better this complex mechanism by integrating distinct dimensional insights. With an integrative review of research into three important perspectives, one nurturing from the Service-Dominant logic, another one based on the information and communication technologies (ICTs) platforms, and (the ethical values-driven) Marketing 3.0 paradigm, this article proposes a conceptual framework in which consumers' ethical values and transcendent motivations play an important role in encouraging their engagement in co-creation activities. In this connection, and with consumers increasingly embracing the need to fulfill a social and ethical function in society, the co-creation process is here comprehended as a means to emphasize the social and moral aspects of co-creation. This article also identifies the important, supportive role of the Marketing 3.0 paradigm and Web 3.0 tools to initiate the co-creation process, as well as the important valuable benefits attained by both companies and consumers after consumers engage in this process. Importantly, these benefits are highlighted to increase when ethical products are the object of these co-creation activities. All these insights have notable implications for both research and managerial practice. PMID:27303349

77 FR 38597 - Multistakeholder Process To Develop Consumer Data Privacy Code of Conduct Concerning Mobile...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-28

... Process To Develop Consumer Data Privacy Code of Conduct Concerning Mobile Application Transparency AGENCY... convene the first meeting of a privacy multistakeholder process concerning mobile application transparency... concerning mobile application transparency. Stakeholders will engage in an open, transparent, consensus...

Presenting quality data to vulnerable groups: charts, summaries or behavioral economic nudges?

PubMed

Elbel, Brian; Gillespie, Colleen; Raven, Maria C

2014-07-01

Despite the increased focus on health care consumers' active choice, not enough is known about how to best facilitate the choice process. We sought to assess methods of improving this process for vulnerable consumers in the United States by testing alternatives that emphasize insights from behavioral economics, or 'nudges'. We performed a hypothetical choice experiment where subjects were randomized to one of five experimental conditions and asked to choose a health center (location where they would receive all their care). The conditions presented the same information about health centers in different ways, including graphically as a chart, via written summary and using behavioral economics, 'nudging' consumers toward particular choices. We hypothesized that these 'nudges' might help simplify the choice process. Our primary outcomes focused on the health center chosen and whether consumers were willing to accept 'nudges'. We found that consumer choice was influenced by the method of presentation and the majority of consumers accepted the health center they were 'nudged' towards. Consumers were accepting of choices grounded in insights from behavioral economics and further consideration should be given to their role in patient choice. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Using Time-Driven Activity-Based Costing as a Key Component of the Value Platform: A Pilot Analysis of Colonoscopy, Aortic Valve Replacement and Carpal Tunnel Release Procedures.

PubMed

Martin, Jacob A; Mayhew, Christopher R; Morris, Amanda J; Bader, Angela M; Tsai, Mitchell H; Urman, Richard D

2018-04-01

Time-driven activity-based costing (TDABC) is a methodology that calculates the costs of healthcare resources consumed as a patient moves along a care process. Limited data exist on the application of TDABC from the perspective of an anesthesia provider. We describe the use of TDABC, a bottom-up costing strategy and financial outcomes for three different medical-surgical procedures. In each case, a multi-disciplinary team created process maps describing the care delivery cycle for a patient encounter using the TDABC methodology. Each step in a process map delineated an activity required for delivery of patient care. The resources (personnel, equipment and supplies) associated with each step were identified. A per minute cost for each resource expended was generated, known as the capacity cost rate, and multiplied by its time requirement. The total cost for an episode of care was obtained by adding the cost of each individual resource consumed as the patient moved along a clinical pathway. We built process maps for colonoscopy in the gastroenterology suite, calculated costs of an aortic valve replacement by comparing surgical aortic valve replacement (SAVR) versus transcatheter aortic valve replacement (TAVR) techniques, and determined the cost of carpal tunnel release in an operating room versus an ambulatory procedure room. TDABC is central to the value-based healthcare platform. Application of TDABC provides a framework to identify process improvements for health care delivery. The first case demonstrates cost-savings and improved wait times by shifting some of the colonoscopies scheduled with an anesthesiologist from the main hospital to the ambulatory facility. In the second case, we show that the deployment of an aortic valve via the transcatheter route front loads the costs compared to traditional, surgical replacement. The last case demonstrates significant cost savings to the healthcare system associated with re-organization of staff required to execute a carpal tunnel release.

Using Time-Driven Activity-Based Costing as a Key Component of the Value Platform: A Pilot Analysis of Colonoscopy, Aortic Valve Replacement and Carpal Tunnel Release Procedures

PubMed Central

Martin, Jacob A.; Mayhew, Christopher R.; Morris, Amanda J.; Bader, Angela M.; Tsai, Mitchell H.; Urman, Richard D.

2018-01-01

Background Time-driven activity-based costing (TDABC) is a methodology that calculates the costs of healthcare resources consumed as a patient moves along a care process. Limited data exist on the application of TDABC from the perspective of an anesthesia provider. We describe the use of TDABC, a bottom-up costing strategy and financial outcomes for three different medical-surgical procedures. Methods In each case, a multi-disciplinary team created process maps describing the care delivery cycle for a patient encounter using the TDABC methodology. Each step in a process map delineated an activity required for delivery of patient care. The resources (personnel, equipment and supplies) associated with each step were identified. A per minute cost for each resource expended was generated, known as the capacity cost rate, and multiplied by its time requirement. The total cost for an episode of care was obtained by adding the cost of each individual resource consumed as the patient moved along a clinical pathway. Results We built process maps for colonoscopy in the gastroenterology suite, calculated costs of an aortic valve replacement by comparing surgical aortic valve replacement (SAVR) versus transcatheter aortic valve replacement (TAVR) techniques, and determined the cost of carpal tunnel release in an operating room versus an ambulatory procedure room. Conclusions TDABC is central to the value-based healthcare platform. Application of TDABC provides a framework to identify process improvements for health care delivery. The first case demonstrates cost-savings and improved wait times by shifting some of the colonoscopies scheduled with an anesthesiologist from the main hospital to the ambulatory facility. In the second case, we show that the deployment of an aortic valve via the transcatheter route front loads the costs compared to traditional, surgical replacement. The last case demonstrates significant cost savings to the healthcare system associated with re-organization of staff required to execute a carpal tunnel release. PMID:29511420

16 CFR 433.3 - Exemption of sellers taking or receiving open end consumer credit contracts before November 1...

Code of Federal Regulations, 2010 CFR

2010-01-01

... make loans, from time to time, directly from the creditor or indirectly by use of a credit card, check... open end consumer credit contracts before November 1, 1977 from requirements of § 433.2(a). 433.3... CONSUMERS' CLAIMS AND DEFENSES § 433.3 Exemption of sellers taking or receiving open end consumer credit...

Improving Overall Equipment Effectiveness Using CPM and MOST: A Case Study of an Indonesian Pharmaceutical Company

NASA Astrophysics Data System (ADS)

Omega, Dousmaris; Andika, Aditya

2017-12-01

This paper discusses the results of a research conducted on the production process of an Indonesian pharmaceutical company. The company is experiencing low performance in the Overall Equipment Effectiveness (OEE) metric. The OEE of the company machines are below world class standard. The machine that has the lowest OEE is the filler machine. Through observation and analysis, it is found that the cleaning process of the filler machine consumes significant amount of time. The long duration of the cleaning process happens because there is no structured division of jobs between cleaning operators, differences in operators’ ability, and operators’ inability in utilizing available cleaning equipment. The company needs to improve the cleaning process. Therefore, Critical Path Method (CPM) analysis is conducted to find out what activities are critical in order to shorten and simplify the cleaning process in the division of tasks. Afterwards, The Maynard Operation and Sequence Technique (MOST) method is used to reduce ineffective movement and specify the cleaning process standard time. From CPM and MOST, it is obtained the shortest time of the cleaning process is 1 hour 28 minutes and the standard time is 1 hour 38.826 minutes.

77 FR 38305 - Agency Information Collection Activities; Announcement of Office of Management and Budget...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-27

...; ``Real Time'' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne...' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne Illness Outbreaks... ```Real Time' Surveys of Consumers' Knowledge, Perceptions and Reported Behavior Concerning Foodborne...

A small frog that makes a big difference: brain wave testing of TV advertisements.

PubMed

Ohme, Rafal; Matukin, Michal

2012-01-01

It is important for the marketing industry to better understand the role of the unconscious and emotions in advertising communication and shopping behavior. Yet, traditional consumer research is not enough for such a purpose. Conventional paper-and-pencil or verbal declarations favor conscious pragmatism and functionality as the principles underlying consumer decisions and motives. These approaches should be combined with an emerging discipline (consumer neuroscience or neuromarketing) to examine the brain and its functioning in the context of consumer choices. It has been widely acknowledged that patterns of brain activity are closely related to consumers cognition and behavior. Thus, the analysis of consumers neurophysiology may increase the understanding of how consumers process incoming information and how they use their memory and react emotionally (See "Three Types of Brain Wave Research on TV Advertisements"): Moreover, as the majority of consumer mental processes occur below the level of conscious awareness, observations of the brain reactions enable researchers to reach the very core (which is consciously inaccessible) foundations of consumer decisions, emotions, motivations, and preferences.

Consumer Health Informatics: Past, Present, and Future of a Rapidly Evolving Domain.

PubMed

Demiris, G

2016-05-20

Consumer Health Informatics (CHI) is a rapidly growing domain within the field of biomedical and health informatics. The objective of this paper is to reflect on the past twenty five years and showcase informatics concepts and applications that led to new models of care and patient empowerment, and to predict future trends and challenges for the next 25 years. We discuss concepts and systems based on a review and analysis of published literature in the consumer health informatics domain in the last 25 years. The field was introduced with the vision that one day patients will be in charge of their own health care using informatics tools and systems. Scientific literature in the field originally focused on ways to assess the quality and validity of available printed health information, only to grow significantly to cover diverse areas such as online communities, social media, and shared decision-making. Concepts such as home telehealth, mHealth, and the quantified-self movement, tools to address transparency of health care organizations, and personal health records and portals provided significant milestones in the field. Consumers are able to actively participate in the decision-making process and to engage in health care processes and decisions. However, challenges such as health literacy and the digital divide have hindered us from maximizing the potential of CHI tools with a significant portion of underserved populations unable to access and utilize them. At the same time, at a global scale consumer tools can increase access to care for underserved populations in developing countries. The field continues to grow and emerging movements such as precision medicine and the sharing economy will introduce new opportunities and challenges.

Consumer Health Informatics: Past, Present, and Future of a Rapidly Evolving Domain

PubMed Central

2016-01-01

Summary Objectives Consumer Health Informatics (CHI) is a rapidly growing domain within the field of biomedical and health informatics. The objective of this paper is to reflect on the past twenty five years and showcase informatics concepts and applications that led to new models of care and patient empowerment, and to predict future trends and challenges for the next 25 years. Methods We discuss concepts and systems based on a review and analysis of published literature in the consumer health informatics domain in the last 25 years. Results The field was introduced with the vision that one day patients will be in charge of their own health care using informatics tools and systems. Scientific literature in the field originally focused on ways to assess the quality and validity of available printed health information, only to grow significantly to cover diverse areas such as online communities, social media, and shared decision-making. Concepts such as home telehealth, mHealth, and the quantified-self movement, tools to address transparency of health care organizations, and personal health records and portals provided significant milestones in the field. Conclusion Consumers are able to actively participate in the decision-making process and to engage in health care processes and decisions. However, challenges such as health literacy and the digital divide have hindered us from maximizing the potential of CHI tools with a significant portion of underserved populations unable to access and utilize them. At the same time, at a global scale consumer tools can increase access to care for underserved populations in developing countries. The field continues to grow and emerging movements such as precision medicine and the sharing economy will introduce new opportunities and challenges. PMID:27199196

Integrating values and consumer involvement in guidelines with the patient at the center: article 8 in Integrating and coordinating efforts in COPD guideline development. An official ATS/ERS workshop report.

PubMed

Kelson, Marcia; Akl, Elie A; Bastian, Hilda; Cluzeau, Françoise; Curtis, J Randall; Guyatt, Gordon; Montori, Victor M; Oliver, Sandy; Schünemann, Holger J

2012-12-01

Professional societies, like many other organizations around the world, have recognized the need to use rigorous processes to ensure that healthcare recommendations are informed by the best available research evidence. They are also realizing the need to involve consumers of healthcare (patients, caregivers, and the public) and integrate their values and preferences in clinical guideline development. This is the eighth of a series of 14 articles that were prepared to advise guideline developers in respiratory and other diseases. It focuses on where to find information about consumer values and preferences, at what points in the guideline development process to integrate their values and preferences, and why. In this review, we addressed the following questions: (1) What do we mean by "consumers"? (2) Why integrate the values and preferences of consumers of healthcare (patients, caregivers, and the public) into clinical practice guidelines? (3) What are the sources of information on consumer values? (4) When and how should consumer values and preferences be integrated into chronic obstructive pulmonary disease guideline recommendations? We defined consumers as patients, caregivers, and members of the public, excluding groups that may also be identified as consumers of guidelines including health professionals, providers, and commissioners of services. We searched PubMed and other databases of methodological studies for existing systematic reviews and relevant methodological research. We did not conduct systematic reviews ourselves. Our conclusions are based on available evidence, supplemented by a rapid appraisal of a selection of qualitative studies, experience of what guideline developers are doing, and workshop discussions. A clear distinction needs to be made between the use of information on consumer values and preferences by guideline developers, and the direct involvement of consumers in guideline development processes. Sources of information on consumer values include the research literature and direct elicitation of values both from organizations representing consumer interests and from individuals. To complement the identification of consumer values, there are a range of methods for involving consumers at all stages of guideline development, from consultation to direct membership of guideline development groups. Evidence-based guidelines need to consider explicitly the values and preferences of all relevant stakeholders (including those of consumers) and to provide opportunities for patients, caregivers, and the public to engage in the processes that consider and integrate those values into the development of guideline recommendations.

Simplifying the negotiating process with physicians: critical elements in negotiating from private practice to employed physician.

PubMed

Gallucci, Armen; Deutsch, Thomas; Youngquist, Jaymie

2013-01-01

The authors attempt to simplify the key elements to the process of negotiating successfully with private physicians. From their experience, the business elements that have resulted in the most discussion center on the compensation including the incentive plan. Secondarily, how the issue of malpractice is handled will also consume a fair amount of time. What the authors have also learned is that the intangible issues can often be the reason for an unexpectedly large amount of discussion and therefore add time to the negotiation process. To assist with this process, they have derived a negotiation checklist, which seeks to help hospital leaders and administrators set the proper framework to ensure successful negotiation conversations. More importantly, being organized and recognizing these broad issues upfront and remaining transparent throughout the process will help to ensure a successful negotiation.

Automatic sample changer control software for automation of neutron activation analysis process in Malaysian Nuclear Agency

NASA Astrophysics Data System (ADS)

Yussup, N.; Ibrahim, M. M.; Rahman, N. A. A.; Mokhtar, M.; Salim, N. A. A.; Soh@Shaari, S. C.; Azman, A.; Lombigit, L.; Azman, A.; Omar, S. A.

2018-01-01

Most of the procedures in neutron activation analysis (NAA) process that has been established in Malaysian Nuclear Agency (Nuclear Malaysia) since 1980s were performed manually. These manual procedures carried out by the NAA laboratory personnel are time consuming and inefficient especially for sample counting and measurement process. The sample needs to be changed and the measurement software needs to be setup for every one hour counting time. Both of these procedures are performed manually for every sample. Hence, an automatic sample changer system (ASC) that consists of hardware and software is developed to automate sample counting process for up to 30 samples consecutively. This paper describes the ASC control software for NAA process which is designed and developed to control the ASC hardware and call GammaVision software for sample measurement. The software is developed by using National Instrument LabVIEW development package.

Application of information theory methods to food web reconstruction

USGS Publications Warehouse

Moniz, L.J.; Cooch, E.G.; Ellner, S.P.; Nichols, J.D.; Nichols, J.M.

2007-01-01

In this paper we use information theory techniques on time series of abundances to determine the topology of a food web. At the outset, the food web participants (two consumers, two resources) are known; in addition we know that each consumer prefers one of the resources over the other. However, we do not know which consumer prefers which resource, and if this preference is absolute (i.e., whether or not the consumer will consume the non-preferred resource). Although the consumers and resources are identified at the beginning of the experiment, we also provide evidence that the consumers are not resources for each other, and the resources do not consume each other. We do show that there is significant mutual information between resources; the model is seasonally forced and some shared information between resources is expected. Similarly, because the model is seasonally forced, we expect shared information between consumers as they respond to the forcing of the resources. The model that we consider does include noise, and in an effort to demonstrate that these methods may be of some use in other than model data, we show the efficacy of our methods with decreasing time series size; in this particular case we obtain reasonably clear results with a time series length of 400 points. This approaches ecological time series lengths from real systems.

Consumer server: A UNIX based event distributor in new CDF data acquisition system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abe, F.; Morita, Y.; Nomachi, M.

1994-12-31

Consumer Server is a program to handle event data and consumer trigger requests I/Os among Level 3 farm and consumer processes in CDF new data acquisition system. This program uses standard UNIX libraries and commercial network technologies to obtain higher portability. The authors describe the concept and configuration of the Consumer Server and report its performance.

Consumer protection and managed care: the need for organized consumers.

PubMed

Rodwin, M A

1996-01-01

Despite its many advantages, managed care creates new problems for consumers. Activists have proposed four types of remedies: (1) increased information and choice; (2) standards for services and marketing; (3) administrative oversight; and (4) procedural due process for complaints. Each approach offers some benefits, but they are insufficient to cope with consumer problems. What is lacking is effective, organized consumer advocacy.

Sterilization processes. Meeting the demands of today's health care technology.

PubMed

Crow, S

1993-09-01

Universal Precautions dictate sterilization for all invasive equipment that break the blood barrier; however, current methods of sterilization, such as steam and ethylene oxide gas (ETO), are not compatible with many of the delicate, heat-sensitive surgical instruments used in modern health care. In addition, traditional sterilization methods are often too time consuming for practical use in the operating room. Clearly, new sterilization processes need to be developed. In this article, the criteria modern sterilization processes must meet and how some manufacturers plan to meet this challenge are discussed. In addition, the pros and cons of using peracetic acid (the newest sterilization process currently available) are examined.

The productive techniques and constitutive effects of 'evidence-based policy' and 'consumer participation' discourses in health policy processes.

PubMed

Lancaster, K; Seear, K; Treloar, C; Ritter, A

2017-03-01

For over twenty years there have been calls for greater 'consumer' participation in health decision-making. While it is recognised by governments and other stakeholders that 'consumer' participation is desirable, barriers to meaningful involvement nonetheless remain. It has been suggested that the reifying of 'evidence-based policy' may be limiting opportunities for participation, through the way this discourse legitimates particular voices to the exclusion of others. Others have suggested that assumptions underpinning the very notion of the 'affected community' or 'consumers' as fixed and bounded 'policy publics' need to be problematised. In this paper, drawing on interviews (n = 41) with individuals closely involved in Australian drug policy discussions, we critically interrogate the productive techniques and constitutive effects of 'evidence-based policy' and 'consumer participation' discourses in the context of drug policy processes. To inform our analysis, we draw on and combine a number of critical perspectives including Foucault's concept of subjugated knowledges, the work of feminist theorists, as well as recent work regarding conceptualisations of emergent policy publics. First, we explore how the subject position of 'consumer' might be seen as enacted in the material-discursive practices of 'evidence-based policy' and 'consumer participation' in drug policy processes. Secondly, we consider the centralising power-effects of the dominant 'evidence-based policy' paradigm, and how resistance may be thought about in this context. We suggest that such interrogation has potential to recast the call for 'consumer' participation in health policy decision-making and drug policy processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Automatic-heuristic and executive-analytic processing during reasoning: Chronometric and dual-task considerations.

PubMed

De Neys, Wim

2006-06-01

Human reasoning has been shown to overly rely on intuitive, heuristic processing instead of a more demanding analytic inference process. Four experiments tested the central claim of current dual-process theories that analytic operations involve time-consuming executive processing whereas the heuristic system would operate automatically. Participants solved conjunction fallacy problems and indicative and deontic selection tasks. Experiment 1 established that making correct analytic inferences demanded more processing time than did making heuristic inferences. Experiment 2 showed that burdening the executive resources with an attention-demanding secondary task decreased correct, analytic responding and boosted the rate of conjunction fallacies and indicative matching card selections. Results were replicated in Experiments 3 and 4 with a different secondary-task procedure. Involvement of executive resources for the deontic selection task was less clear. Findings validate basic processing assumptions of the dual-process framework and complete the correlational research programme of K. E. Stanovich and R. F. West (2000).

Ocean Simulation Model. Version 2. First Order Frontal Simulation

DTIC Science & Technology

1991-05-01

REAL DEP(NXVS),TEMP(MXVS),SAL(MXVS),SIG(MXVS), DVF (MXVS), * DEP2(MXVS),TEMP2(MXVS),SAL2(MXVS),SIG2CMXVS),BVF2(MXVS), * DEPO(MXVS), TEMPO(MX)VS),SALO...processing parameters to desired values. Generating the Front Position Directive FRNT uses the current clock time as initial seed to call the intrinsic...potentially be very time consuming if the parameter ITER is set to a large number. Directive RES was designed to allow the user to resume the HELM

The Test and Evaluation Uses of Heterogeneous Computing: GPGPUs and Other Approaches

DTIC Science & Technology

2011-03-01

is commonly held that test and evaluation (T& E ) is one of the most critical steps in the development of virtually all defense systems (Fox et al. 2003...T& E of current systems is an elaborate and time-consuming process that reflects both the intricacies of the object of the test and the range of...bases (Kepner 2004). These questions are even more urgent because increasing emphasis in T& E concerns the expenditures of money and time in the

Multiple-Strain Approach and Probabilistic Modeling of Consumer Habits in Quantitative Microbial Risk Assessment: A Quantitative Assessment of Exposure to Staphylococcal Enterotoxin A in Raw Milk.

PubMed

Crotta, Matteo; Rizzi, Rita; Varisco, Giorgio; Daminelli, Paolo; Cunico, Elena Cosciani; Luini, Mario; Graber, Hans Ulrich; Paterlini, Franco; Guitian, Javier

2016-03-01

Quantitative microbial risk assessment (QMRA) models are extensively applied to inform management of a broad range of food safety risks. Inevitably, QMRA modeling involves an element of simplification of the biological process of interest. Two features that are frequently simplified or disregarded are the pathogenicity of multiple strains of a single pathogen and consumer behavior at the household level. In this study, we developed a QMRA model with a multiple-strain approach and a consumer phase module (CPM) based on uncertainty distributions fitted from field data. We modeled exposure to staphylococcal enterotoxin A in raw milk in Lombardy; a specific enterotoxin production module was thus included. The model is adaptable and could be used to assess the risk related to other pathogens in raw milk as well as other staphylococcal enterotoxins. The multiplestrain approach, implemented as a multinomial process, allowed the inclusion of variability and uncertainty with regard to pathogenicity at the bacterial level. Data from 301 questionnaires submitted to raw milk consumers were used to obtain uncertainty distributions for the CPM. The distributions were modeled to be easily updatable with further data or evidence. The sources of uncertainty due to the multiple-strain approach and the CPM were identified, and their impact on the output was assessed by comparing specific scenarios to the baseline. When the distributions reflecting the uncertainty in consumer behavior were fixed to the 95th percentile, the risk of exposure increased up to 160 times. This reflects the importance of taking into consideration the diversity of consumers' habits at the household level and the impact that the lack of knowledge about variables in the CPM can have on the final QMRA estimates. The multiple-strain approach lends itself to use in other food matrices besides raw milk and allows the model to better capture the complexity of the real world and to be capable of geographical specificity.

Sustainability in health care by allocating resources effectively (SHARE) 4: exploring opportunities and methods for consumer engagement in resource allocation in a local healthcare setting.

PubMed

Harris, Claire; Ko, Henry; Waller, Cara; Sloss, Pamela; Williams, Pamela

2017-05-05

This is the fourth in a series of papers reporting a program of Sustainability in Health care by Allocating Resources Effectively (SHARE) in a local healthcare setting. Healthcare decision-makers have sought to improve the effectiveness and efficiency of services through removal or restriction of practices that are unsafe or of little benefit, often referred to as 'disinvestment'. A systematic, integrated, evidence-based program for disinvestment was being established within a large Australian health service network. Consumer engagement was acknowledged as integral to this process. This paper reports the process of developing a model to integrate consumer views and preferences into an organisation-wide approach to resource allocation. A literature search was conducted and interviews and workshops were undertaken with health service consumers and staff. Findings were drafted into a model for consumer engagement in resource allocation which was workshopped and refined. Although consumer engagement is increasingly becoming a requirement of publicly-funded health services and documented in standards and policies, participation in organisational decision-making is not widespread. Several consistent messages for consumer engagement in this context emerged from the literature and consumer responses. Opportunities, settings and activities for consumer engagement through communication, consultation and participation were identified within the resource allocation process. Sources of information regarding consumer values and perspectives in publications and locally-collected data, and methods to use them in health service decision-making, were identified. A model bringing these elements together was developed. The proposed model presents potential opportunities and activities for consumer engagement in the context of resource allocation.

Consumer confidence in the safety of food and newspaper coverage of food safety issues: a longitudinal perspective.

PubMed

de Jonge, Janneke; Van Trijp, Hans; Renes, Reint Jan; Frewer, Lynn J

2010-01-01

This study develops a longitudinal perspective on consumer confidence in the safety of food to explore if, how, and why consumer confidence changes over time. In the first study, a theory-based monitoring instrument for consumer confidence in the safety of food was developed and validated. The monitoring instrument assesses consumer confidence together with its determinants. Model and measurement invariance were validated rigorously before developments in consumer confidence in the safety of food and its determinants were investigated over time. The results from the longitudinal analysis show that across four waves of annual data collection (2003-2006), the framework was stable and that the relative importance of the determinants of confidence was, generally, constant over time. Some changes were observed regarding the mean ratings on the latent constructs. The second study explored how newspaper coverage of food safety related issues affects consumer confidence in the safety of food through subjective consumer recall of food safety incidents. The results show that the newspaper coverage on food safety issues is positively associated with consumer recall of food safety incidents, both in terms of intensity and recency of media coverage.

75 FR 47606 - Strategic Plan for Consumer Education via Cooperative Agreement (U18)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-06

... or quantitative research with stakeholders and meetings with stakeholder groups and consumer experts... and resulting from an extensive consumer research process. In 2007, PFSE joined with USDA to create... responsibilities of FDA. B. Research Objectives PFSE supports a large, complex, and multi-faceted consumer food...

Reflections on how to write and organise a research thesis.

PubMed

Hardy, Sally; Ramjeet, Janet

2005-01-01

Writing up research projects and presenting a thesis are among the most challenging and time-consuming elements of the research process. The authors provide a structured guideline to help students, particularly those undertaking Master's degrees while still practising in clinical areas, to overcome the challenges of writing their thesis and produce a cogent, logical and reflective piece of work.

The State Authorization Reciprocity Agreement (SARA): A Good Idea Whose Time Has Come

ERIC Educational Resources Information Center

Longanecker, David; Hill, Marshall A.

2014-01-01

In this article the authors argue that states need a new way to oversee the delivery of postsecondary distance education across state borders. They assert that the current process is too spotty to assure consistent consumer protection and too cumbersome and expensive for institutions. Because education is not specified in the US Constitution as a…

Engaging Students as Tutors, Trainers, and Leaders

ERIC Educational Resources Information Center

Derrick, Deirdre

2015-01-01

While starting a tutoring program may seem like a daunting and time-consuming task, it does not have to be. The best way to approach the creation and development of a tutoring service is with a list of clear objectives. In this article, the author describes the process she used to create a tutoring program with her English as a foreign language…

Low Frequency Vibration approach to asess the Performance of wood structural Systems

Treesearch

Xiping Wang; Robert J. Ross; Michael O. Hunt

2004-01-01

The primary means of inspecting buildings and other structures is to evaluate each structure member individually. This is a time consuming process that is expensive, particularly if sheathing or other covering materials must be removed to access the structural members. This paper presents an effort to use a low frequency vibration method for assessing the structural...

The Use of Novel Camtasia Videos to Improve Performance of At-Risk Students in Undergraduate Physiology Courses

ERIC Educational Resources Information Center

Miller, Cynthia J.

2014-01-01

Students in undergraduate physiology courses often have difficulty understanding complex, multi-step processes, and these concepts consume a large portion of class time. For this pilot study, it was hypothesized that online multimedia resources may improve student performance in a high-risk population and reduce the in-class workload. A narrated…

Recovery of Picloram and 2,4-Dichlorophenoxyacetic Acid from Aqueous Samples by Reversed-Phase Solid-Phase Extraction

Treesearch

Martha J.M. Wells; Jerry L. Michael

1987-01-01

Extensive preparation of samples before chromatographic analysis is usually the most time-consuming process in the determination of many organic compounds in environmental matrices. In the past, removal of some organic from aqueous solution was commonly done by liquid/liquid extraction. However, the introduction of stable, covalently bonded reversed-phase sorbents now...

Evaluating the Effectiveness of Contact Tracing on Tuberculosis Outcomes in Saskatchewan Using Individual-Based Modeling

ERIC Educational Resources Information Center

Tian, Yuan; Osgood, Nathaniel D.; Al-Azem, Assaad; Hoeppner, Vernon H.

2013-01-01

Tuberculosis (TB) is a potentially fatal disease spread by an airborne pathogen infecting approximately one third of the globe. For decades, contact tracing (CT) has served a key role in the control of TB and many other notifiable communicable diseases. Unfortunately, CT is a labor-intensive and time-consuming process and is often conducted by a…

Classification of shiga toxin-producing escherichia coli (STEC) serotypes with hyperspectral microscope imagery

USDA-ARS?s Scientific Manuscript database

Non-O157:H7 Shiga toxin-producing Escherichia coli (STEC) strains such as O26, O45, O103, O111, O121 and O145 are recognized as serious outbreak to cause human illness due to their toxicity. Since a conventional microbiological method for cell counting is laborious and time-consuming process, optica...

A Novel Method for the In-Depth Multimodal Analysis of Student Learning Trajectories in Intelligent Tutoring Systems

ERIC Educational Resources Information Center

Liu, Ran; Stamper, John; Davenport, Jodi

2018-01-01

Temporal analyses are critical to understanding learning processes, yet understudied in education research. Data from different sources are often collected at different grain sizes, which are difficult to integrate. Making sense of data at many levels of analysis, including the most detailed levels, is highly time-consuming. In this paper, we…

Comparison of an automated Most Probable Number (MPN) technique to traditional plating methods for estimating populations of total aerobes, coliforms and E. coli associated with freshly processed broiler chickens

USDA-ARS?s Scientific Manuscript database

Traditional microbiological techniques for estimating populations of viable bacteria can be laborious and time consuming. The Most Probable Number (MPN) technique is especially tedious as multiple series of tubes must be inoculated at several different dilutions. Recently, an instrument (TEMPOTM) ...

Low frequency vibration approach for assessing performance of wood floor systems

Treesearch

Xiping Wang; Robert J. Ross; Michael O. Hunt; John R. Erickson; John W. Forsman

2005-01-01

The primary means of inspecting buildings and other structures is to evaluate each structure member individually. This is a time-consuming and expensive process, particularly if sheathing or other covering materials must be removed to access the structural members. The objective of this study was to determine if a low frequency vibration method could be used to...

Thematic and positional accuracy assessment of digital remotely sensed data

Treesearch

Russell G. Congalton

2007-01-01

Accuracy assessment or validation has become a standard component of any land cover or vegetation map derived from remotely sensed data. Knowing the accuracy of the map is vital to any decisionmaking performed using that map. The process of assessing the map accuracy is time consuming and expensive. It is very important that the procedure be well thought out and...

Developing a Machine-Supported Coding System for Constructed-Response Items in PISA. Research Report. ETS RR-17-47

ERIC Educational Resources Information Center

Yamamoto, Kentaro; He, Qiwei; Shin, Hyo Jeong; von Davier, Mattias

2017-01-01

Approximately a third of the Programme for International Student Assessment (PISA) items in the core domains (math, reading, and science) are constructed-response items and require human coding (scoring). This process is time-consuming, expensive, and prone to error as often (a) humans code inconsistently, and (b) coding reliability in…

Fast generation of computer-generated holograms using wavelet shrinkage.

PubMed

Shimobaba, Tomoyoshi; Ito, Tomoyoshi

2017-01-09

Computer-generated holograms (CGHs) are generated by superimposing complex amplitudes emitted from a number of object points. However, this superposition process remains very time-consuming even when using the latest computers. We propose a fast calculation algorithm for CGHs that uses a wavelet shrinkage method, eliminating small wavelet coefficient values to express approximated complex amplitudes using only a few representative wavelet coefficients.

AMDIS Case Conference

PubMed Central

Graham, J.; Levick, D.; Schreiber, R.

2010-01-01

Clinical decision support that provides enhanced patient safety at the point of care frequently encounters significant pushback from clinicians who find the process intrusive or time-consuming. We present a hypothetical medical center’s dilemma about its allergy alerting system and discuss similar problems faced by real hospitals. We then share some lessons learned and best practices for institutions who wish to implement these tools themselves. PMID:23616828

Exploring a Literacy Website that Works: ReadWriteThink.org

ERIC Educational Resources Information Center

Anderson, Rebecca S.; Balajthy, Ernest

2007-01-01

While it is easy to find lesson plans on the Internet, the quality of plans and the formats in which they are written vary considerably, and the process of sifting through the chaff in order to find the wheat can be time-consuming and discouraging. To address these concerns the authors of this Technology in Literacy column introduce…

I, S, T, and J Grading Techniques for Es, Ns, Fs, and Ps: Insights from the MBTI on Managing the Grading Process

ERIC Educational Resources Information Center

Fornaciari, Charles J.; Lund Dean, Kathy

2013-01-01

Most instructors at least occasionally experience grading student work as a frustrating, time-consuming task. The Myers-Briggs Type Indicator (MBTI) instrument can be a powerful self-awareness tool for management educators seeking to enhance their grading techniques. Evidence suggests that many management professors prefer Extraversion (E),…

Forecasting of indirect consumables for a Job Shop

NASA Astrophysics Data System (ADS)

Shakeel, M.; Khan, S.; Khan, W. A.

2016-08-01

A job shop has an arrangement where similar machines (Direct consumables) are grouped together and use indirect consumables to produce a product. The indirect consumables include hack saw blades, emery paper, painting brush etc. The job shop is serving various orders at a particular time for the optimal operation of job shop. Forecasting is required to predict the demand of direct and indirect consumables in a job shop. Forecasting is also needed to manage lead time, optimize inventory cost and stock outs. The objective of this research is to obtain the forecast for indirect consumables. The paper shows how job shop can manage their indirect consumables more accurately by establishing a new technique of forecasting. This results in profitable use of job shop by multiple users.

Shared decision making in the recovery of people with schizophrenia: the role of metacognitive capacities in insight and pragmatic language use.

PubMed

Chan, Kevin K S; Mak, Winnie W S

2012-08-01

In the development of consumer-centered care for mental health consumers with schizophrenia, one key ingredient is consumer participation in health care decisions together with their healthcare providers, termed "shared decision making" (SDM). SDM requires consumers to form a number of complex ideas about themselves and their providers then use that knowledge to make sense of the illness and reach medical and psychosocial decisions. However, metacognitive deficits widely observed in schizophrenia might lead to poor insight and pragmatic language deficits in some consumers, disrupting the whole process by which a personal and consensually valid narrative account of psychiatric challenges is synthesized and flexibly evolved. Given the current understanding that it is possible to improve metacognition, in this article we summarize how Metacognitive Training (MCT) and individual psychotherapy could potentially be tailored, or modified, to help consumers to develop metacognitive capacities with an end goal of facilitating the SDM process. Consistent with the principles of consumer-defined recovery, we also suggest a strategy for engaging consumers in SDM dialogue based on "where the consumers are at". Providers are advised to be cognizant of their medically driven perspective and attempt to work with the consumers in the perspective of the consumers' own recovery goals. Copyright © 2012 Elsevier Ltd. All rights reserved.

Responding rapidly to FDA drug withdrawals: design and application of a new approach for a consumer health website.

PubMed

Embi, Peter J; Acharya, Prasad; McCuistion, Mark; Kishman, Charles P; Haag, Doris; Marine, Stephen

2006-09-06

Information about drug withdrawals may not reach patients in a timely manner, and this could result in adverse events. Increasingly, the public turns to consumer health websites for health information, but such sites may not update their content for days or weeks following important events like Food and Drug Administration (FDA) drug withdrawal actions. There is no recognized standard for how quickly consumer health websites should respond to such events, and reports addressing this issue are lacking. The objective of this study was to develop and implement an approach to enhance the efficiency with which a consumer health website (NetWellness.org) responds to FDA drug withdrawal actions. Evaluation of the current approach used by NetWellness staff to update content affected by FDA action revealed a slow process driven by the goal of performing thorough and comprehensive review and editing. To achieve our desired goal of accurately updating affected content within 24 hours of FDA action, we developed a strategy that included rapid updating of affected Web pages with warning boxes and hyperlinks to the information about the withdrawal. With the next FDA withdrawal event, that of valdecoxib (Bextra) on April 7, 2005, we applied this new approach, observed the time and resource requirements, and monitored the rate at which consumers viewed the updated information to gauge its potential impact. Application of the new approach allowed one person to modify the affected Web pages in less than 1 hour and within 18 hours of the FDA announcement. Using the old strategy, response to a similar event, the withdrawal of rofecoxib (Vioxx) 6 months earlier, had taken over 3 weeks and the efforts of several personnel. Updated valdecoxib content received 188 hits within the first month and 4285 hits within 1 year. Rapid updating of a consumer health website's content in response to an FDA drug withdrawal event was easily accomplished by applying the approach described. This allowed consumers to view accurate information regarding the withdrawn drug much sooner than would otherwise have been the case. Given that consumers increasingly turn to websites for their health information, adoption of a rapid response standard for important health events like FDA drug withdrawals should be considered by the consumer health informatics community.

Evolutionary model of an anonymous consumer durable market

NASA Astrophysics Data System (ADS)

Kaldasch, Joachim

2011-07-01

An analytic model is presented that considers the evolution of a market of durable goods. The model suggests that after introduction goods spread always according to a Bass diffusion. However, this phase will be followed by a diffusion process for durable consumer goods governed by a variation-selection-reproduction mechanism and the growth dynamics can be described by a replicator equation. The theory suggests that products play the role of species in biological evolutionary models. It implies that the evolution of man-made products can be arranged into an evolutionary tree. The model suggests that each product can be characterized by its product fitness. The fitness space contains elements of both sites of the market, supply and demand. The unit sales of products with a higher product fitness compared to the mean fitness increase. Durables with a constant fitness advantage replace other goods according to a logistic law. The model predicts in particular that the mean price exhibits an exponential decrease over a long time period for durable goods. The evolutionary diffusion process is directly related to this price decline and is governed by Gompertz equation. Therefore it is denoted as Gompertz diffusion. Describing the aggregate sales as the sum of first, multiple and replacement purchase the product life cycle can be derived. Replacement purchase causes periodic variations of the sales determined by the finite lifetime of the good (Juglar cycles). The model suggests that both, Bass- and Gompertz diffusion may contribute to the product life cycle of a consumer durable. The theory contains the standard equilibrium view of a market as a special case. It depends on the time scale, whether an equilibrium or evolutionary description is more appropriate. The evolutionary framework is used to derive also the size, growth rate and price distribution of manufacturing business units. It predicts that the size distribution of the business units (products) is lognormal, while the growth rates exhibit a Laplace distribution. Large price deviations from the mean price are also governed by a Laplace distribution (fat tails). These results are in agreement with empirical findings. The explicit comparison of the time evolution of consumer durables with empirical investigations confirms the close relationship between price decline and Gompertz diffusion, while the product life cycle can be described qualitatively for a long time period.

Standardization of pitch-range settings in voice acoustic analysis.

PubMed

Vogel, Adam P; Maruff, Paul; Snyder, Peter J; Mundt, James C

2009-05-01

Voice acoustic analysis is typically a labor-intensive, time-consuming process that requires the application of idiosyncratic parameters tailored to individual aspects of the speech signal. Such processes limit the efficiency and utility of voice analysis in clinical practice as well as in applied research and development. In the present study, we analyzed 1,120 voice files, using standard techniques (case-by-case hand analysis), taking roughly 10 work weeks of personnel time to complete. The results were compared with the analytic output of several automated analysis scripts that made use of preset pitch-range parameters. After pitch windows were selected to appropriately account for sex differences, the automated analysis scripts reduced processing time of the 1,120 speech samples to less than 2.5 h and produced results comparable to those obtained with hand analysis. However, caution should be exercised when applying the suggested preset values to pathological voice populations.

Numerical techniques for high-throughput reflectance interference biosensing

NASA Astrophysics Data System (ADS)

Sevenler, Derin; Ünlü, M. Selim

2016-06-01

We have developed a robust and rapid computational method for processing the raw spectral data collected from thin film optical interference biosensors. We have applied this method to Interference Reflectance Imaging Sensor (IRIS) measurements and observed a 10,000 fold improvement in processing time, unlocking a variety of clinical and scientific applications. Interference biosensors have advantages over similar technologies in certain applications, for example highly multiplexed measurements of molecular kinetics. However, processing raw IRIS data into useful measurements has been prohibitively time consuming for high-throughput studies. Here we describe the implementation of a lookup table (LUT) technique that provides accurate results in far less time than naive methods. We also discuss an additional benefit that the LUT method can be used with a wider range of interference layer thickness and experimental configurations that are incompatible with methods that require fitting the spectral response.

Real-time assessment of critical quality attributes of a continuous granulation process.

PubMed

Fonteyne, Margot; Vercruysse, Jurgen; Díaz, Damián Córdoba; Gildemyn, Delphine; Vervaet, Chris; Remon, Jean Paul; De Beer, Thomas

2013-02-01

There exists the intention to shift pharmaceutical manufacturing of solid dosage forms from traditional batch production towards continuous production. The currently applied conventional quality control systems, based on sampling and time-consuming off-line analyses in analytical laboratories, would annul the advantages of continuous processing. It is clear that real-time quality assessment and control is indispensable for continuous production. This manuscript evaluates strengths and weaknesses of several complementary Process Analytical Technology (PAT) tools implemented in a continuous wet granulation process, which is part of a fully continuous from powder-to-tablet production line. The use of Raman and NIR-spectroscopy and a particle size distribution analyzer is evaluated for the real-time monitoring of critical parameters during the continuous wet agglomeration of an anhydrous theophylline- lactose blend. The solid state characteristics and particle size of the granules were analyzed in real-time and the critical process parameters influencing these granule characteristics were identified. The temperature of the granulator barrel, the amount of granulation liquid added and, to a lesser extent, the powder feed rate were the parameters influencing the solid state of the active pharmaceutical ingredient (API). A higher barrel temperature and a higher powder feed rate, resulted in larger granules.

Scheduling with non-decreasing deterioration jobs and variable maintenance activities on a single machine

NASA Astrophysics Data System (ADS)

Zhang, Xingong; Yin, Yunqiang; Wu, Chin-Chia

2017-01-01

There is a situation found in many manufacturing systems, such as steel rolling mills, fire fighting or single-server cycle-queues, where a job that is processed later consumes more time than that same job when processed earlier. The research finds that machine maintenance can improve the worsening of processing conditions. After maintenance activity, the machine will be restored. The maintenance duration is a positive and non-decreasing differentiable convex function of the total processing times of the jobs between maintenance activities. Motivated by this observation, the makespan and the total completion time minimization problems in the scheduling of jobs with non-decreasing rates of job processing time on a single machine are considered in this article. It is shown that both the makespan and the total completion time minimization problems are NP-hard in the strong sense when the number of maintenance activities is arbitrary, while the makespan minimization problem is NP-hard in the ordinary sense when the number of maintenance activities is fixed. If the deterioration rates of the jobs are identical and the maintenance duration is a linear function of the total processing times of the jobs between maintenance activities, then this article shows that the group balance principle is satisfied for the makespan minimization problem. Furthermore, two polynomial-time algorithms are presented for solving the makespan problem and the total completion time problem under identical deterioration rates, respectively.

What Is Direct-to-Consumer Genetic Testing?

MedlinePlus

... consumer genetic testing? What is direct-to-consumer genetic testing? Most of the time, genetic testing is ... testing. For more information about direct-to-consumer genetic testing: Centers for Disease Control and Prevention (CDC) ...

Effects of shopping addiction on consumer decision-making: Web-based studies in real time.

PubMed

Lo, Hui-Yi; Harvey, Nigel

2012-12-01

Background and aims Most research into compulsive buying has focused on its causes: questionnaires have been used to study its association with various factors assumed to be important in its etiology. Few studies have dealt with the effects of being a compulsive buyer on shopping decisions. Also, processes underlying compulsive buying are dynamic but questionnaires give access only to a retrospective view of them from the standpoint of the participant. The aim of the current study was to investigate the decision processes underlying compulsive buying. Methods Two simulated shopping experiments, each with over 100 participants, were used to compare the decision processes of compulsive shoppers with those of non-compulsive shoppers. This approach allowed us to measure many features of consumer decision-making that are relevant to compulsive shopping. Results Compulsive shoppers differed from general shoppers in six ways: choice characteristics, searching behavior, overspending, budget-consciousness, effects of credit card availability, and emotional responses to overspending. Conclusions Results are consistent with the view that compulsive buying, like other behavioral addictions, develops because the cognitive system under-predicts the extent of post-addiction craving produced by emotional and visceral processes.

ERP implementation in hospitals: a case study.

PubMed

Agarwal, Divya; Garg, Poonam

2012-01-01

In a competitive healthcare sector, hospitals have to focus on their processes in order to deliver high-quality care while at the same time reducing costs. Many hospitals have decided to adopt one or another Enterprise Resource Planning (ERP) system to improve their businesses, but implementing an ERP system can be a demanding endeavour. The systems are so difficult to implement that some are successful; many have failed, causing multimillion dollar losses. The challenge of ERP solutions lie in implementation because they are complex, time consuming and expensive too. This paper describes the various process workflows and phases of ERP implementation at Fortis Hospital Cunningham Road, Bangalore, India. This knowledge will provide valuable insights for the researchers and practitioners to understand the different process workflows and to make informed decisions when implementing ERP in any hospital.

A complexity-scalable software-based MPEG-2 video encoder.

PubMed

Chen, Guo-bin; Lu, Xin-ning; Wang, Xing-guo; Liu, Ji-lin

2004-05-01

With the development of general-purpose processors (GPP) and video signal processing algorithms, it is possible to implement a software-based real-time video encoder on GPP, and its low cost and easy upgrade attract developers' interests to transfer video encoding from specialized hardware to more flexible software. In this paper, the encoding structure is set up first to support complexity scalability; then a lot of high performance algorithms are used on the key time-consuming modules in coding process; finally, at programming level, processor characteristics are considered to improve data access efficiency and processing parallelism. Other programming methods such as lookup table are adopted to reduce the computational complexity. Simulation results showed that these ideas could not only improve the global performance of video coding, but also provide great flexibility in complexity regulation.

Tenderness, moistness, and flavor of pre- and postrigor marinated broiler breast fillets evaluated by consumer sensory panel.

PubMed

Saha, A; Perumalla, A V S; Lee, Y; Meullenet, J F; Owens, C M

2009-06-01

Prerigor deboning and marination of broiler breast fillets are growing trends in the poultry industry. Marination can often enhance product attributes such as flavor, juiciness, and texture. The purpose of this study was to evaluate consumer acceptance of marinated broiler breast fillets deboned pre- (<4 h postmortem) and postrigor (>or= 4 h postmortem). A total of 400 broiler carcasses were processed using an inline system and deboned at various times: 0.25, 1.25, 2, 2.5, 3, 3.5, 4, 6, and 24 h postmortem. A 2-stage chilling system was used for all treatments with the exception of the 0.25 h treatment, which was deboned before chilling. After chilling, carcasses or fillets, or both, were aged on ice. Breast fillets were marinated with a 1% salt and 0.45% phosphate final concentration. Consumer sensory evaluations for moistness, tenderness, saltiness, flavor, and overall impression were obtained on all treatments using hedonic and just-about-right (JAR) scales. Although there were slight differences in hedonic ratings for overall impression, texture, and flavor of marinated breast fillets, all treatments could be categorized as "like slightly" to "like moderately." Using a JAR scale, only a small percentage of consumers (<18%) considered any of the treatments as "too tough." The scores for overall flavor or moistness were not affected by the deboning times because the majority of the people considered them to be JAR. Most the consumers reported the potential for purchase of the product as "probably would buy" to "may or may not buy." The results of this study indicate that marination of prerigor deboned meat (with 1% salt) is effective in producing product similar to marinated postrigor deboned meat, suggesting its effectiveness in improving meat quality attributes of early deboned meat.

Utilization of community pharmacy space to enhance privacy: a qualitative study.

PubMed

Hattingh, H Laetitia; Emmerton, Lynne; Ng Cheong Tin, Pascale; Green, Catherine

2016-10-01

Community pharmacists require access to consumers' information about their medicines and health-related conditions to make informed decisions regarding treatment options. Open communication between consumers and pharmacists is ideal although consumers are only likely to disclose relevant information if they feel that their privacy requirements are being acknowledged and adhered to. This study sets out to explore community pharmacy privacy practices, experiences and expectations and the utilization of available space to achieve privacy. Qualitative methods were used, comprising a series of face-to-face interviews with 25 pharmacists and 55 pharmacy customers in Perth, Western Australia, between June and August 2013. The use of private consultation areas for certain services and sensitive discussions was supported by pharmacists and consumers although there was recognition that workflow processes in some pharmacies may need to change to maximize the use of private areas. Pharmacy staff adopted various strategies to overcome privacy obstacles such as taking consumers to a quieter part of the pharmacy, avoiding exposure of sensitive items through packaging, lowering of voices, interacting during pharmacy quiet times and telephoning consumers. Pharmacy staff and consumers regularly had to apply judgement to achieve the required level of privacy. Management of privacy can be challenging in the community pharmacy environment, and on-going work in this area is important. As community pharmacy practice is increasingly becoming more involved in advanced medication and disease state management services with unique privacy requirements, pharmacies' layouts and systems to address privacy challenges require a proactive approach. © 2015 The Authors. Health Expectations Published by John Wiley & Sons Ltd.

Design of forging process variables under uncertainties

NASA Astrophysics Data System (ADS)

Repalle, Jalaja; Grandhi, Ramana V.

2005-02-01

Forging is a complex nonlinear process that is vulnerable to various manufacturing anomalies, such as variations in billet geometry, billet/die temperatures, material properties, and workpiece and forging equipment positional errors. A combination of these uncertainties could induce heavy manufacturing losses through premature die failure, final part geometric distortion, and reduced productivity. Identifying, quantifying, and controlling the uncertainties will reduce variability risk in a manufacturing environment, which will minimize the overall production cost. In this article, various uncertainties that affect the forging process are identified, and their cumulative effect on the forging tool life is evaluated. Because the forging process simulation is time-consuming, a response surface model is used to reduce computation time by establishing a relationship between the process performance and the critical process variables. A robust design methodology is developed by incorporating reliability-based optimization techniques to obtain sound forging components. A case study of an automotive-component forging-process design is presented to demonstrate the applicability of the method.

Does Consuming Sugar and Artificial Sweeteners Change Taste Preferences?

PubMed Central

Bartolotto, Carole

2015-01-01

Americans consume a lot of sugar, primarily from sweeteners that are added to processed foods and beverages. Data from the US Department of Agriculture reveals that in 2013, Americans consumed 22.3 teaspoons of added caloric sweeteners a day, which is significantly more than the American Heart Association’s recommendation. Artificial and alternative sweeteners have also been added to a plethora of foods. These sweeteners range from about 180 times sweeter to as much as 13,000 times sweeter than sugar. Consumption of both sugar and artificial sweeteners may be changing our palates or taste preferences over time, increasing our desire for sweet foods. Unfortunately, the data on this are lacking. In the summer of 2014, a group of 20 people from Kaiser Permanente facilities throughout California agreed to cut out all added sugars and artificial sweeteners for 2 weeks and then complete a survey to determine whether their taste preferences had changed. After the 2-week challenge, 95% of participants (18 out of 19 respondents) found that sweet foods and drinks tasted sweeter or too sweet, 75% (15 out of 20 respondents) found that other foods tasted sweeter, and 95% (19 out of 20 respondents) said moving forward they would use less or even no sugar. Additionally, 86.6% of participants (13 out of 15 respondents) stopped craving sugar after 6 days. Although this was a small survey, the results suggest that using a 2-week sugar challenge can help to reset taste preferences and make consuming less or no sugar easier. Physicians should consider recommending a sugar and artificial sweetener challenge to all their patients, especially those with obesity, diabetes, or cardiovascular disease. PMID:26176574

Semi-automatic image analysis methodology for the segmentation of bubbles and drops in complex dispersions occurring in bioreactors

NASA Astrophysics Data System (ADS)

Taboada, B.; Vega-Alvarado, L.; Córdova-Aguilar, M. S.; Galindo, E.; Corkidi, G.

2006-09-01

Characterization of multiphase systems occurring in fermentation processes is a time-consuming and tedious process when manual methods are used. This work describes a new semi-automatic methodology for the on-line assessment of diameters of oil drops and air bubbles occurring in a complex simulated fermentation broth. High-quality digital images were obtained from the interior of a mechanically stirred tank. These images were pre-processed to find segments of edges belonging to the objects of interest. The contours of air bubbles and oil drops were then reconstructed using an improved Hough transform algorithm which was tested in two, three and four-phase simulated fermentation model systems. The results were compared against those obtained manually by a trained observer, showing no significant statistical differences. The method was able to reduce the total processing time for the measurements of bubbles and drops in different systems by 21-50% and the manual intervention time for the segmentation procedure by 80-100%.

Real-time spectral characterization of a photon pair source using a chirped supercontinuum seed.

PubMed

Erskine, Jennifer; England, Duncan; Kupchak, Connor; Sussman, Benjamin

2018-02-15

Photon pair sources have wide ranging applications in a variety of quantum photonic experiments and protocols. Many of these protocols require well controlled spectral correlations between the two output photons. However, due to low cross-sections, measuring the joint spectral properties of photon pair sources has historically been a challenging and time-consuming task. Here, we present an approach for the real-time measurement of the joint spectral properties of a fiber-based four wave mixing source. We seed the four wave mixing process using a broadband chirped pulse, studying the stimulated process to extract information regarding the spontaneous process. In addition, we compare stimulated emission measurements with the spontaneous process to confirm the technique's validity. Joint spectral measurements have taken many hours historically and several minutes with recent techniques. Here, measurements have been demonstrated in 5-30 s depending on resolution, offering substantial improvement. Additional benefits of this approach include flexible resolution, large measurement bandwidth, and reduced experimental overhead.

Low cost MATLAB-based pulse oximeter for deployment in research and development applications.

PubMed

Shokouhian, M; Morling, R C S; Kale, I

2013-01-01

Problems such as motion artifact and effects of ambient lights have forced developers to design different signal processing techniques and algorithms to increase the reliability and accuracy of the conventional pulse oximeter device. To evaluate the robustness of these techniques, they are applied either to recorded data or are implemented on chip to be applied to real-time data. Recorded data is the most common method of evaluating however it is not as reliable as real-time measurements. On the other hand, hardware implementation can be both expensive and time consuming. This paper presents a low cost MATLAB-based pulse oximeter that can be used for rapid evaluation of newly developed signal processing techniques and algorithms. Flexibility to apply different signal processing techniques, providing both processed and unprocessed data along with low implementation cost are the important features of this design which makes it ideal for research and development purposes, as well as commercial, hospital and healthcare application.

Residential Customer Enrollment in Time-based Rate and Enabling Technology Programs: Smart Grid Investment Grant Consumer Behavior Study Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, Annika; Cappers, Peter; Goldman, Charles

2013-05-01

The U.S. Department of Energy’s (DOE’s) Smart Grid Investment Grant (SGIG) program is working with a subset of the 99 SGIG projects undertaking Consumer Behavior Studies (CBS), which examine the response of mass market consumers (i.e., residential and small commercial customers) to time-varying electricity prices (referred to herein as time-based rate programs) in conjunction with the deployment of advanced metering infrastructure (AMI) and associated technologies. The effort presents an opportunity to advance the electric industry’s understanding of consumer behavior.

Effects of instant controlled pressure drop process on physical and sensory properties of puffed wheat snack.

PubMed

Yağcı, Sibel

2017-04-01

In this study, research on the development of a puffed wheat snack using the instant controlled pressure drop (DIC) process was carried out. Snack products were produced by expanding moistened wheat under various DIC processing conditions in order to obtain adequate puffing, followed by drying in a hot air dryer. The effects of operational variables such as wheat initial moisture content (11-23% w/w, wet basis), processing pressure (3-5 × 10 2 kPa) and processing time (3-11 min) on the physical (density, color and textural characteristics) and sensory properties of the product were investigated. The physical properties of the wheat snack were most affected by changes in processing pressure, followed by processing time and wheat moisture content. Increasing processing pressure and time often improved expansion and textural properties but led to darkening of the raw wheat color. The most acceptable snack in terms of physical properties was obtained at the lowest wheat moisture content. Sensory analysis suggested that consumer acceptability was optimal for wheat snacks produced at higher processing pressure, medium processing time and lower moisture content. The most desirable conditions for puffed wheat snack production using the DIC process were determined as 11% (w/w) of wheat moisture content, 5 × 10 2 kPa of processing pressure and 7 min of processing time. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Potential Economic Benefits of Consumer Education.

ERIC Educational Resources Information Center

Ferguson, Allen R.; And Others

A study explored the potential economic impacts of a large and successful national program of consumer education. Following a literature review, a qualitative analysis was performed on a wide range of topics. The topics pertained to information and the process of consumer choice, the role of advertising, consumer sovereignty and the supply system,…

The Frontier of Research in the Consumer Interest. Proceedings of the International Conference on Research in the Consumer Interest (Racine, Wisconsin, August 16-19, 1986).

ERIC Educational Resources Information Center

Maynes, E. Scott, Ed.; And Others

The following papers are included: "JFK's Four Consumer Rights" (Lampman); "Product Safety" (Gerner); "Use of Cost-Benefit Analysis in Product Safety Regulation" (Crandall); "CPCS's Voluntary Standards" (Ault); "Consumer Safety and Issue Emergence Process" (Mayer); "Reflections on Research in…

The Role of Advertising in Adolescent Consumer Learning.

ERIC Educational Resources Information Center

Moore, Roy L.; Moschis, George P.

A total of 734 sixth through twelfth grade students completed two questionnaires in a study that focused on the development of consumer skills, the sources of consumer skill acquisition, the effects of cognitive development and social factors on the socialization processes, and the effects of levels of competency on various consumer skills. A…

Food processing by animals: do beavers leach tree bark to improve palatability?

PubMed

Müller-Schwarze, D; Brashear, H; Kinnel, R; Hintz, K A; Lioubomirov, A; Skibo, C

2001-05-01

Beavers store and consume tree parts in the bodies of water where they live. We examined whether such soaking renders food more palatable by leaching out undesirable compounds. In experiment 1, saplings of red maple, Acer rubrum (RM), were first soaked in a pond for periods of 2, 18, and 36 days, then offered to free-ranging beavers. Soaking for two days rendered RM slightly more acceptable to beavers. To further examine the time window around two days, RM sticks were soaked in distilled water in the laboratory for 1, 2, 4, and 6 days before presenting them to beavers (experiment 2). In experiment 3, twigs of three species were placed on land. Beavers placed RM in the water for 1 to 3 days before consuming the twigs. In experiment 4, sticks were provided in the water at Cranberry Lake Biological Station (CLBS). Most quaking aspen (QA) was consumed during the first night, and most witch hazel, Hamamelis virginiana (WH), during the third night. At Allegany State Park (ASP), no such difference was found. Twigs were provided in the water in experiment 5. At ASP, WH was taken after three days in the water, and at CLBS little WH was consumed, and only during the third night. A meta-analysis of all experiments shows that relatively more WH is consumed after two days than any other species. Experiment 6 traced the time beavers left their own harvested branches in the water. Unlike other tree species, WH remained in the water for two to four days before being consumed. Experiment 7 measured the phenolics leached into water from RM twigs and small pieces of bark soaked for 10 and 8 days, respectively. Shredded bark lost 50-60% of leachable phenolics into the water, and twigs 70-80%. We conclude that beavers can use water to leach undesirable compounds from their food. Although this effect was not robust, our study is the first of its kind.

Selection of human consumables for future space missions

NASA Technical Reports Server (NTRS)

Bourland, C. T.; Smith, M. C.

1991-01-01

Consumables for human spaceflight include oxygen, water, food and food packaging, personal hygiene items, and clothing. This paper deals with the requirements for food and water, and their impact on waste product generation. Just as urbanization of society has been made possible by improved food processing and packaging, manned spaceflight has benefitted from this technology. The downside of this technology is increased food package waste product. Since consumables make up a major portion of the vehicle onboard stowage and generate most of the waste products, selection of consumables is a very critical process. Food and package waste comprise the majority of the trash generated on the current shuttle orbiter missions. Plans for future missions must include accurate assessment of the waste products to be generated, and the methods for processing and disposing of these wastes.

The perceived healthiness of functional foods. A conjoint study of Danish, Finnish and American consumers' perception of functional foods.

PubMed

Bech-Larsen, Tino; Grunert, Klaus G

2003-02-01

Functional foods presumably enable the consumer to lead a healthier life without changing eating habits. Whether consumers accept this proposition or not is potentially influenced by their perceptions of the healthiness of the processing methods, enrichment components, food-types, and health claims used in the production and marketing of functional foods. Because consumers may perceive functional enrichment as interfering with nature, cultural values pertaining to man's manipulation of nature may also influence consumer acceptance of functional foods. The purpose of the study described here is to clarify to which extent Danish, Finnish and American consumers' perceptions of the healthiness of functional foods are explained by the factors mentioned above. The general results indicate that values pertaining to man's manipulation of nature is only modestly related to the acceptance of functional foods, whereas the use of different health claims, processing methods, enrichments, product types, and especially the interactions between the two latter, are important determinants of consumers' perceptions of the healthiness of functional foods.

Motivational factors for consuming omega-3 PUFAs: an exploratory study with Danish consumers.

PubMed

Krutulyte, Rasa; Grunert, Klaus G; Scholderer, Joachim; Hagemann, Kit Skov; Elgaard, Peter; Nielsen, Brian; Graverholt, Jens Peter

2008-07-01

Growing consumer awareness of functional foods and understanding of their positive nutritional effects have led to the need of specific studies and have captured more attention than ever before. In Europe, Danish consumers have been found to be relatively negative towards the concept of functional foods. This paper presents the results of a qualitative pilot study that aimed to explore Danish consumers' motives for choosing omega-3/fish oil enriched products. The Health Action Process Approach (HAPA) was applied as a theoretical framework to understand the process by which people choose healthy foods. By conducting qualitative in-depth interviews the study mostly focused on the role of behavioural intention predictors such as risk perception, outcome expectations and self-efficacy. The results of the study suggest that consumers' understanding of healthy eating as such does not relate to the choice of omega-3/fish oil, whereas perception of omega-3 as an ingredient in selected foods does indeed influence consumers' choice of carrier-ingredient combinations.

Quad-phased data mining modeling for dementia diagnosis.

PubMed

Bang, Sunjoo; Son, Sangjoon; Roh, Hyunwoong; Lee, Jihye; Bae, Sungyun; Lee, Kyungwon; Hong, Changhyung; Shin, Hyunjung

2017-05-18

The number of people with dementia is increasing along with people's ageing trend worldwide. Therefore, there are various researches to improve a dementia diagnosis process in the field of computer-aided diagnosis (CAD) technology. The most significant issue is that the evaluation processes by physician which is based on medical information for patients and questionnaire from their guardians are time consuming, subjective and prone to error. This problem can be solved by an overall data mining modeling, which subsidizes an intuitive decision of clinicians. Therefore, in this paper we propose a quad-phased data mining modeling consisting of 4 modules. In Proposer Module, significant diagnostic criteria are selected that are effective for diagnostics. Then in Predictor Module, a model is constructed to predict and diagnose dementia based on a machine learning algorism. To help clinical physicians understand results of the predictive model better, in Descriptor Module, we interpret causes of diagnostics by profiling patient groups. Lastly, in Visualization Module, we provide visualization to effectively explore characteristics of patient groups. The proposed model is applied for CREDOS study which contains clinical data collected from 37 university-affiliated hospitals in republic of Korea from year 2005 to 2013. This research is an intelligent system enabling intuitive collaboration between CAD system and physicians. And also, improved evaluation process is able to effectively reduce time and cost consuming for clinicians and patients.

Mars ISRU for Production of Mission Critical Consumables - Options, Recent Studies, and Current State of the Art

NASA Technical Reports Server (NTRS)

Sanders, G. B.; Paz, A.; Oryshchyn, L.; Araghi, K.; Muscatello, A.; Linne, D.; Kleinhenz, J.; Peters, T.

2015-01-01

In 1978, a ground breaking paper titled, "Feasibility of Rocket Propellant Production on Mars" by Ash, Dowler, and Varsi discussed how ascent propellants could be manufactured on the Mars surface from carbon dioxide collected from the atmosphere to reduce launch mass. Since then, the concept of making mission critical consumables such as propellants, fuel cell reactants, and life support consumables from local resources, commonly known as In-Situ Resource Utilization (ISRU), for robotic and human missions to Mars has been studied many times. In the late 1990's, NASA initiated a series of Mars Human Design Reference Missions (DRMs), the first of which was released in 1997. These studies primarily focused on evaluating the impact of making propellants on Mars for crew ascent to Mars orbit, but creating large caches of life support consumables (water & oxygen) as a backup for regenerative life support systems for long-duration surface stays (>500 days) was also considered in Mars DRM 3.0. Until science data from the Mars Odyssey orbiter and subsequent robotic missions revealed that water may be widely accessable across the surface of Mars, prior Mars ISRU studies were limited to processing Mars atmospheric resources (carbon dioxide, nitrogen, argon, oxygen, and water vapor). In December 2007, NASA completed the Mars Human Design Reference Architecture (DRA) 5.0 study which considered water on Mars as a potential resource for the first time in a human mission architecture. While knowledge of both water resources on Mars and the hardware required to excavate and extract the water were very preliminary, the study concluded that a significant reduction in mass and significant enhancements to the mission architecture were possible if Mars water resources were utilized. Two subsequent Mars ISRU studies aimed at reexamining ISRU technologies, processing options, and advancements in the state-of-the-art since 2007 and to better understand the volume and packaging associated with Mars ISRU systems further substantiated the preliminary results from the Mars DRA 5.0 study. This paper will provide an overview of Mars ISRU consumable production options, the analyses, results, and conclusions from the Mars DRA 5.0 (2007), Mars Collaborative (2013), and Mars ISRU Payload for the Supersonic Retro Propulsion (2014) mission studies, and the current state-of-the-art of Mars ISRU technologies and systems. The paper will also briefly discuss the mission architectural implications associated with Mars resource and ISRU processing options.

Integrating consumer engagement in health and medical research - an Australian framework.

PubMed

Miller, Caroline L; Mott, Kathy; Cousins, Michael; Miller, Stephanie; Johnson, Anne; Lawson, Tony; Wesselingh, Steve

2017-02-10

Quality practice of consumer engagement is still in its infancy in many sectors of medical research. The South Australian Health and Medical Research Institute (SAHMRI) identified, early in its development, the opportunity to integrate evidence-driven consumer and community engagement into its operations. SAHMRI partnered with Health Consumers Alliance and consumers in evidence generation. A Partnership Steering Committee of researchers and consumers was formed for the project. An iterative mixed-method qualitative process was used to generate a framework for consumer engagement. This process included a literature review followed by semi-structured interviews with experts in consumer engagement and lead medical researchers, group discussions and a consensus workshop with the Partnership Steering Committee, facilitated by Health Consumer Alliance. The literature revealed a dearth of evidence about effective consumer engagement methodologies. Four organisational dimensions are reported to contribute to success, namely governance, infrastructure, capacity and advocacy. Key themes identified through the stakeholder interviews included sustained leadership, tangible benefits, engagement strategies should be varied, resourcing, a moral dimension, and challenges. The consensus workshop produced a framework and tangible strategies. Comprehensive examples of consumer participation in health and medical research are limited. There are few documented studies of what techniques are effective. This evidence-driven framework, developed in collaboration with consumers, is being integrated in a health and medical research institute with diverse programs of research. This framework is offered as a contribution to the evidence base around meaningful consumer engagement and as a template for other research institutions to utilise.

Acousto-optic time- and space-integrating spotlight-mode SAR processor

NASA Astrophysics Data System (ADS)

Haney, Michael W.; Levy, James J.; Michael, Robert R., Jr.

1993-09-01

The technical approach and recent experimental results for the acousto-optic time- and space- integrating real-time SAR image formation processor program are reported. The concept overcomes the size and power consumption limitations of electronic approaches by using compact, rugged, and low-power analog optical signal processing techniques for the most computationally taxing portions of the SAR imaging problem. Flexibility and performance are maintained by the use of digital electronics for the critical low-complexity filter generation and output image processing functions. The results include a demonstration of the processor's ability to perform high-resolution spotlight-mode SAR imaging by simultaneously compensating for range migration and range/azimuth coupling in the analog optical domain, thereby avoiding a highly power-consuming digital interpolation or reformatting operation usually required in all-electronic approaches.

Colt: an experiment in wormhole run-time reconfiguration

NASA Astrophysics Data System (ADS)

Bittner, Ray; Athanas, Peter M.; Musgrove, Mark

1996-10-01

Wormhole run-time reconfiguration (RTR) is an attempt to create a refined computing paradigm for high performance computational tasks. By combining concepts from field programmable gate array (FPGA) technologies with data flow computing, the Colt/Stallion architecture achieves high utilization of hardware resources, and facilitates rapid run-time reconfiguration. Targeted mainly at DSP-type operations, the Colt integrated circuit -- a prototype wormhole RTR device -- compares favorably to contemporary DSP alternatives in terms of silicon area consumed per unit computation and in computing performance. Although emphasis has been placed on signal processing applications, general purpose computation has not been overlooked. Colt is a prototype that defines an architecture not only at the chip level but also in terms of an overall system design. As this system is realized, the concept of wormhole RTR will be applied to numerical computation and DSP applications including those common to image processing, communications systems, digital filters, acoustic processing, real-time control systems and simulation acceleration.

Processed and ultra-processed food products: consumption trends in Canada from 1938 to 2011.

PubMed

Moubarac, Jean-Claude; Batal, Malek; Martins, Ana Paula Bortoletto; Claro, Rafael; Levy, Renata Bertazzi; Cannon, Geoffrey; Monteiro, Carlos

2014-01-01

A classification of foods based on the nature, extent, and purpose of industrial food processing was used to assess changes in household food expenditures and dietary energy availability between 1938 and 2011 in Canada. Food acquisitions from six household food budget surveys (1938/1939 , 1953, 1969, 1984, 2001, and 2011) were classified into unprocessed or minimally processed foods, processed culinary ingredients, and ready-to-consume processed or ultra-processed products. Contributions of each group to household food expenditures, and to dietary energy availability (kcal per capita) were calculated. During the period studied, household expenditures and dietary energy availability fell for both unprocessed or minimally processed foods and culinary ingredients, and rose for ready-to-consume products. The caloric share of foods fell from 34.3% to 25.6% and from 37% to 12.7% for culinary ingredients. The share of ready-to-consume products rose from 28.7% to 61.7%, and the increase was especially noteworthy for those that were ultra-processed. The most important factor that has driven changes in Canadian dietary patterns between 1938 and 2011 is the replacement of unprocessed or minimally processed foods and culinary ingredients used in the preparation of dishes and meals; these have been displaced by ready-to-consume ultra-processed products. Nutrition research and practice should incorporate information about food processing into dietary assessments.

From regained function to daily use: experiences of surgical reconstruction of grip in people with tetraplegia.

PubMed

Wangdell, Johanna; Carlsson, Gunnel; Friden, Jan

2014-01-01

To capture patients' relearning processes from regained function to improvements in daily life after grip reconstructive surgery in tetraplegia. Eleven people with tetraplegia who underwent grip reconstructive surgery during February 2009 to March 2011. Qualitative interviews were conducted 7 to 17 months after surgery and analysed using grounded theory. Determination to reach a higher level of independence was the core concept to integrate regained function into daily life. There were 3 phases identified; "Initiate activity training," "Establish hand control in daily activities," and "Challenge dependence." Between the phases psychological stages occurred, first; "a belief in improved ability", and later in the process; "confidence in ability". The process to fully integrate regain function in daily life was described as long and time-consuming. However, the participants claimed it useful to do the skills training in their home environment, without long-term in clinic rehabilitation. Relearning activities in daily life after a grip reconstruction is a time-consuming and demanding process. It includes skills training, mental strategies and psychological stages together with environmental and social factors. Accordingly, rehabilitation after grip reconstruction in tetraplegia should focus on both grip skills and psychological stages, to encourage that patient's keep their determination and achieve greater independence. Implications for Rehabilitation There is a stepwise process to transform improved function into daily use. The most important factor to transform improved function into daily use was motivation to reach a higher independence. Other important factors were; skills training, use of individual learning strategies, belief and confidence in personal ability, social and environmental factors. There was a long and demanding process to fully transform the improved function into daily use. The participants preferred to do activity training in the specific environment, usually at home.

Anticipatory Consumer Socialization.

ERIC Educational Resources Information Center

Moore, Roy L.; Moschis, George P.

Anticipatory consumer socialization is the learning of consumer roles and perceptions, which will be assumed at a later time, such as those that children acquire before they become adult consumers. A survey of 784 adolescents was conducted in a southern state to examine the anticipatory consumer socialization effects of such factors as the mass…

Real time 3D structural and Doppler OCT imaging on graphics processing units

NASA Astrophysics Data System (ADS)

Sylwestrzak, Marcin; Szlag, Daniel; Szkulmowski, Maciej; Gorczyńska, Iwona; Bukowska, Danuta; Wojtkowski, Maciej; Targowski, Piotr

2013-03-01

In this report the application of graphics processing unit (GPU) programming for real-time 3D Fourier domain Optical Coherence Tomography (FdOCT) imaging with implementation of Doppler algorithms for visualization of the flows in capillary vessels is presented. Generally, the time of the data processing of the FdOCT data on the main processor of the computer (CPU) constitute a main limitation for real-time imaging. Employing additional algorithms, such as Doppler OCT analysis, makes this processing even more time consuming. Lately developed GPUs, which offers a very high computational power, give a solution to this problem. Taking advantages of them for massively parallel data processing, allow for real-time imaging in FdOCT. The presented software for structural and Doppler OCT allow for the whole processing with visualization of 2D data consisting of 2000 A-scans generated from 2048 pixels spectra with frame rate about 120 fps. The 3D imaging in the same mode of the volume data build of 220 × 100 A-scans is performed at a rate of about 8 frames per second. In this paper a software architecture, organization of the threads and optimization applied is shown. For illustration the screen shots recorded during real time imaging of the phantom (homogeneous water solution of Intralipid in glass capillary) and the human eye in-vivo is presented.

An investigation of used electronics return flows: a data-driven approach to capture and predict consumers storage and utilization behavior.

PubMed

Sabbaghi, Mostafa; Esmaeilian, Behzad; Raihanian Mashhadi, Ardeshir; Behdad, Sara; Cade, Willie

2015-02-01

Consumers often have a tendency to store their used, old or un-functional electronics for a period of time before they discard them and return them back to the waste stream. This behavior increases the obsolescence rate of used still-functional products leading to lower profitability that could be resulted out of End-of-Use (EOU) treatments such as reuse, upgrade, and refurbishment. These types of behaviors are influenced by several product and consumer-related factors such as consumers' traits and lifestyles, technology evolution, product design features, product market value, and pro-environmental stimuli. Better understanding of different groups of consumers, their utilization and storage behavior and the connection of these behaviors with product design features helps Original Equipment Manufacturers (OEMs) and recycling and recovery industry to better overcome the challenges resulting from the undesirable storage of used products. This paper aims at providing insightful statistical analysis of Electronic Waste (e-waste) dynamic nature by studying the effects of design characteristics, brand and consumer type on the electronics usage time and end of use time-in-storage. A database consisting of 10,063 Hard Disk Drives (HDD) of used personal computers returned back to a remanufacturing facility located in Chicago, IL, USA during 2011-2013 has been selected as the base for this study. The results show that commercial consumers have stored computers more than household consumers regardless of brand and capacity factors. Moreover, a heterogeneous storage behavior is observed for different brands of HDDs regardless of capacity and consumer type factors. Finally, the storage behavior trends are projected for short-time forecasting and the storage times are precisely predicted by applying machine learning methods. Copyright © 2014 Elsevier Ltd. All rights reserved.

Optimization of airport security lanes

NASA Astrophysics Data System (ADS)

Chen, Lin

2018-05-01

Current airport security management system is widely implemented all around the world to ensure the safety of passengers, but it might not be an optimum one. This paper aims to seek a better security system, which can maximize security while minimize inconvenience to passengers. Firstly, we apply Petri net model to analyze the steps where the main bottlenecks lie. Based on average tokens and time transition, the most time-consuming steps of security process can be found, including inspection of passengers' identification and documents, preparing belongings to be scanned and the process for retrieving belongings back. Then, we develop a queuing model to figure out factors affecting those time-consuming steps. As for future improvement, the effective measures which can be taken include transferring current system as single-queuing and multi-served, intelligently predicting the number of security checkpoints supposed to be opened, building up green biological convenient lanes. Furthermore, to test the theoretical results, we apply some data to stimulate the model. And the stimulation results are consistent with what we have got through modeling. Finally, we apply our queuing model to a multi-cultural background. The result suggests that by quantifying and modifying the variance in wait time, the model can be applied to individuals with various habits customs and habits. Generally speaking, our paper considers multiple affecting factors, employs several models and does plenty of calculations, which is practical and reliable for handling in reality. In addition, with more precise data available, we can further test and improve our models.

Performance reporting for consumers: issues for the Australian private hospital sector.

PubMed

Sheahan, Margo; Little, Russ; Leggat, Sandra G

2007-05-30

A group of consumers of private hospital services and their carers collaborated with staff of a Melbourne private hospital and with industry representatives to develop a consumer-driven performance report on cardiac services. During the development process participating consumers identified situational and structural barriers to their right to be informed of costs, to choice and to quality care. Their growing appreciation of these barriers led them to a different perspective on performance reporting, which resulted in their redirecting the project. The consumer participants no longer wanted a performance report that provided comparative quantitative data. Instead they designed a report that outlined the structures, systems and processes the hospital had in place to address the quality and safety of services provided. In addition, consumer participants developed a decision support tool for consumers to use in navigating the private health care sector. The journey of these consumers in creating a consumer driven performance report for a private hospital service may assist those responsible for governance of Australia's health system in choosing appropriate strategies and mechanisms to enhance private hospital accountability. The situational and institutional industry barriers to choice, information and quality identified by these consumers need to be addressed before public performance reporting for private hospitals is introduced in Australia.

Performance reporting for consumers: issues for the Australian private hospital sector

PubMed Central

Sheahan, Margo; Little, Russ; Leggat, Sandra G

2007-01-01

A group of consumers of private hospital services and their carers collaborated with staff of a Melbourne private hospital and with industry representatives to develop a consumer-driven performance report on cardiac services. During the development process participating consumers identified situational and structural barriers to their right to be informed of costs, to choice and to quality care. Their growing appreciation of these barriers led them to a different perspective on performance reporting, which resulted in their redirecting the project. The consumer participants no longer wanted a performance report that provided comparative quantitative data. Instead they designed a report that outlined the structures, systems and processes the hospital had in place to address the quality and safety of services provided. In addition, consumer participants developed a decision support tool for consumers to use in navigating the private health care sector. The journey of these consumers in creating a consumer driven performance report for a private hospital service may assist those responsible for governance of Australia's health system in choosing appropriate strategies and mechanisms to enhance private hospital accountability. The situational and institutional industry barriers to choice, information and quality identified by these consumers need to be addressed before public performance reporting for private hospitals is introduced in Australia. PMID:17537238

Performance and scalability of Fourier domain optical coherence tomography acceleration using graphics processing units.

PubMed

Li, Jian; Bloch, Pavel; Xu, Jing; Sarunic, Marinko V; Shannon, Lesley

2011-05-01

Fourier domain optical coherence tomography (FD-OCT) provides faster line rates, better resolution, and higher sensitivity for noninvasive, in vivo biomedical imaging compared to traditional time domain OCT (TD-OCT). However, because the signal processing for FD-OCT is computationally intensive, real-time FD-OCT applications demand powerful computing platforms to deliver acceptable performance. Graphics processing units (GPUs) have been used as coprocessors to accelerate FD-OCT by leveraging their relatively simple programming model to exploit thread-level parallelism. Unfortunately, GPUs do not "share" memory with their host processors, requiring additional data transfers between the GPU and CPU. In this paper, we implement a complete FD-OCT accelerator on a consumer grade GPU/CPU platform. Our data acquisition system uses spectrometer-based detection and a dual-arm interferometer topology with numerical dispersion compensation for retinal imaging. We demonstrate that the maximum line rate is dictated by the memory transfer time and not the processing time due to the GPU platform's memory model. Finally, we discuss how the performance trends of GPU-based accelerators compare to the expected future requirements of FD-OCT data rates.

An efficient ASIC implementation of 16-channel on-line recursive ICA processor for real-time EEG system.

PubMed

Fang, Wai-Chi; Huang, Kuan-Ju; Chou, Chia-Ching; Chang, Jui-Chung; Cauwenberghs, Gert; Jung, Tzyy-Ping

2014-01-01

This is a proposal for an efficient very-large-scale integration (VLSI) design, 16-channel on-line recursive independent component analysis (ORICA) processor ASIC for real-time EEG system, implemented with TSMC 40 nm CMOS technology. ORICA is appropriate to be used in real-time EEG system to separate artifacts because of its highly efficient and real-time process features. The proposed ORICA processor is composed of an ORICA processing unit and a singular value decomposition (SVD) processing unit. Compared with previous work [1], this proposed ORICA processor has enhanced effectiveness and reduced hardware complexity by utilizing a deeper pipeline architecture, shared arithmetic processing unit, and shared registers. The 16-channel random signals which contain 8-channel super-Gaussian and 8-channel sub-Gaussian components are used to analyze the dependence of the source components, and the average correlation coefficient is 0.95452 between the original source signals and extracted ORICA signals. Finally, the proposed ORICA processor ASIC is implemented with TSMC 40 nm CMOS technology, and it consumes 15.72 mW at 100 MHz operating frequency.

Kpejigaou: an indigenous, high-protein, low-fat, cowpea-based griddled food proposed for coastal West Africa.

PubMed

Amonsou, Eric Oscar; Sakyi-Dawson, Esther; Saalia, Firibu Kwesi; Houssou, Paul

2008-12-01

Griddled cowpea paste foods have high nutritional potential because they are low in fat but high in protein. A good understanding of process and product characteristics of kpejigaou is necessary to improve its quality and enhance acceptability. To describe the product, evaluate critical variables in traditional processing, and determine consumer quality criteria and preferences for kpejigaou. A survey of kpejigaou processing was carried out among processors and regular consumers of kpejigaou. Kpejigaou is flat and circular in shape, with uniform thickness and porous structure. The production process of kpejigaou was found to be simple and rapid, but the quality of the finished product varied among processors and among batches. Critical processing variables affecting quality were dehulling of the cowpeas, type of griddling equipment, and griddling temperature. Texture (sponginess) is the most important quality index that determines the preference and acceptability of kpejigaou by consumers. Traditionally processed kpejigaou does not meet current standards for high-quality foods. This study provides the basis for efforts to standardize the kpejigaou process to ensure consistent product quality and enhance the acceptability of kpejigaou among consumers. Kpejigaou has a potential for success if marketed as a low-fat, nutritious fast food.

Traditional and online consumers in China: a preliminary study of their personality traits and decision-making styles.

PubMed

Zhu, Junpeng; Xu, You; Huang, Jingyi; Yeow, Changdar; Wang, Wei

2012-12-01

Population of online consumers increases rapidly, but the decision-making styles of online consumers and psychiatric denominators such as the personality correlates remain unclear. In 196 traditional, and 196 age-, education- and gender-matched online consumers, we have tested the Zuckerman-Kuhlman Personality Questionnaire (ZKPQ) and the Consumer Style Inventory (CSI). After exploratory and confirmatory factor analyses, we have defined a five-factor model CSI with 24 items. Online consumers scored lower on ZKPQ Neuroticism-Anxiety and higher on Aggression-Hostility than traditional ones did, and scored higher on CSI Novelty-fashion consciousness and Brand consciousness, and lower on Time consciousness than the traditional consumers did. ZKPQ Neuroticism-Anxiety was positively correlated with CSI Confused by overchoice in both groups, Sociability was positively correlated with Novelty-fashion consciousness and negatively with Time consciousness in traditional group, and Impulsive Sensation Seeking was positively correlated with Novelty-fashion consciousness and Time consciousness in online group. Our study suggests that, regarding the decision-making styles, online consumers display curiosity that lacks security and need other ways to improve their social lives. It also calls further designs to address the contributions of other psychiatric features to the particular decision-making styles in online consumers.

The practice and perception of precautionary allergen labelling by the Australasian food manufacturing industry.

PubMed

Zurzolo, G A; Peters, R L; Koplin, J J; de Courten, M; Mathai, M L; Tye-Din, J A; Tang, M L K; Campbell, D E; Ponsonby, A-L; Prescott, S L; Gurrin, L; Dharmage, S C; Allen, K J

2017-07-01

The precautionary allergen labelling (PAL) and Voluntary Incidental Trace Allergen Labelling (VITAL ® ) tools were designed by industry to assist consumers with selecting safe foods for consumption. However, a sizeable proportion of food products bear no label, and it is unclear whether these products are free from allergens and therefore safe to consume or have simply not undergone a risk assessment and therefore remain unlabelled for that reason. To assess the prevalence of unlabelled products that have undergone a risk assessment process and to examine the factors influencing industry's uptake of the VITAL ® process. A web-based questionnaire was distributed to Australasian food and grocery manufacturers. One hundred and thirty-seven Australasian manufacturers were contacted, and 59 questionnaires were returned (response rate: 43%). The respondents represented 454 different manufacturing sites. Manufacturers reported that 23% (95% CI 19-28) of products (n=102/434) that had been through the VITAL ® risk assessment process had no PAL statement on the label. 34% (95% CI 30-38), (n=204/600) of products that had undergone another (non-VITAL ® ) risk assessment process had no PAL statement. In examining the factors that influenced industry's uptake of the VITAL ® process, 25 manufacturers reported on factors that influenced the uptake of the VITAL ® process, 76% (CI 95% 55-91) reported that VITAL ® was an effective tool because it was based on science; 52% (CI 95% 31-72) reported that it was too time-consuming and 36% (CI 95% 18-57) identified a concern with it not being endorsed by the government. Currently, we estimate that at least 30% of products may have been through a risk assessment process and yet bear no PAL statement on the label. Permissive labelling could be incorporated onto these products if they have been assessed to be safe for consumption. © 2017 John Wiley & Sons Ltd.

Dietary habits of a school population and implications for oral health.

PubMed

Llena Puy, C; Forner, L

2010-04-01

The study analyzes the consumption of cariogenic foods in a population of children between 6 and 10 years old. Transversal descriptive study on a sample of 369 children who first attended to the Department 9 Dentistry dental office of the Valencia Region Health Agency (Spain). A self-administered food consumption frequency questionnaire was used to evaluate how often the food on the list were consumed by the children. Sticky sugar-rich foods, sugared milk and dairy products, food containing starch and sugar, sugary liquids and food with semihydrolyzed starch were consumed by over 50% of the sample at main meals and between meals. The mean intake of all these food groups, was over five times a week. The older children ate more fruit and foods rich in semihydrolyzed starch at main meals. Sweetened medication significantly reduced with age. Sugar-free sweets were consumed by almost 60% of the sample. The study shows a high intake of food with cariogenic potential, in particular processed food with added sugar and food with semihydrolyzed starch consumed between meals. This situation indicates the need to include health education programs in our population focused to improve the dietary habits of children and teenagers.

Nursing home consumer complaints and quality of care: a national view.

PubMed

Stevenson, David G

2006-06-01

This study uses 5 years of national data on investigated nursing home complaints (1998-2002) to evaluate whether complaints might be used to assess nursing home quality of care. On-Line Survey Certification and Reporting (OSCAR) data are used to evaluate the association between consumer complaints, facility and resident characteristics, and other nursing home quality measures. The analyses are undertaken in the context of considerable cross-state variation in nursing home complaint processes and rates. Complaints varied across facility characteristics in ways consistent with the nursing home quality literature. Complaints were significantly positively associated with survey deficiencies and the presence of serious survey deficiencies, and significantly negatively associated with nurse and nurse aide staffing. Complaints performance was significantly predictive of survey deficiencies at subsequent inspections. This study presents the first national evidence for using consumer complaints to assess nursing home quality of care. Despite limitations, nursing home complaints appear to offer a real-time signal of quality concerns.

Execution of a parallel edge-based Navier-Stokes solver on commodity graphics processor units

NASA Astrophysics Data System (ADS)

Corral, Roque; Gisbert, Fernando; Pueblas, Jesus

2017-02-01

The implementation of an edge-based three-dimensional Reynolds Average Navier-Stokes solver for unstructured grids able to run on multiple graphics processing units (GPUs) is presented. Loops over edges, which are the most time-consuming part of the solver, have been written to exploit the massively parallel capabilities of GPUs. Non-blocking communications between parallel processes and between the GPU and the central processor unit (CPU) have been used to enhance code scalability. The code is written using a mixture of C++ and OpenCL, to allow the execution of the source code on GPUs. The Message Passage Interface (MPI) library is used to allow the parallel execution of the solver on multiple GPUs. A comparative study of the solver parallel performance is carried out using a cluster of CPUs and another of GPUs. It is shown that a single GPU is up to 64 times faster than a single CPU core. The parallel scalability of the solver is mainly degraded due to the loss of computing efficiency of the GPU when the size of the case decreases. However, for large enough grid sizes, the scalability is strongly improved. A cluster featuring commodity GPUs and a high bandwidth network is ten times less costly and consumes 33% less energy than a CPU-based cluster with an equivalent computational power.

Labeling strategies to overcome the problem of niche markets for sustainable milk products: The example of pasture-raised milk.

PubMed

Kühl, S; Gassler, B; Spiller, A

2017-06-01

Pasture-raised milk is gaining in importance in some European countries and in the United States. The production of pasture-raised milk is linked to higher costs, as the milk is normally collected and processed separately from conventional barn milk. This could hinder the production of sustainable milk products. We discuss alternative labeling strategies that allow the mixing of pasture-raised (sustainable) and conventional milk to reduce costs and break free from the current niche market. The lower price would allow for more pasture-raised milk to be produced and enter the mainstream market. The aim of this study was to analyze consumers' willingness to pay for alternative labeling types using a discrete choice experiment with 1,065 German milk buyers. The 2 alternative labels, besides the classical labeling approach, are based on the mass balance approach (at least 50% pasture-raised milk in a package) and cause-related marketing (support of farmers who keep their cows on pasture). The discrete choice experiment was combined with a cluster analysis to get a deeper understanding of the buying behavior of the diverse consumer segments for milk. We found that all consumer groups prefer the classical label where products are segregated but also understand the benefits of cause-related marketing. The average consumer was willing to pay €0.50 more for pasture-raised milk certified with the classical label and €0.38 more for pasture-raised milk labeled with a cause-related marketing claim. However, differences between the clusters are strong: The smallest cluster of ethically involved consumers (15%) is willing to pay the highest premiums, especially for the classical label. Cause-related marketing is an interesting alternative for involved buyers under price pressure (41%), whereas the mass balance approach is little understood and thus less valued by consumers. From our results we concluded that cause-related marketing (in our case, the support of pasturing of dairy cows) can be useful for dairies for which it is not efficient to collect and process products separately. This approach is furthermore suitable for reaching consumers who are mainly interested in altruistic issues but at the same time are more price sensitive, as this labeling strategy does not need separate collection and processing and can thereby be marketed at a lower price. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Rui; Praggastis, Brenda L.; Smith, William P.

While streaming data have become increasingly more popular in business and research communities, semantic models and processing software for streaming data have not kept pace. Traditional semantic solutions have not addressed transient data streams. Semantic web languages (e.g., RDF, OWL) have typically addressed static data settings and linked data approaches have predominantly addressed static or growing data repositories. Streaming data settings have some fundamental differences; in particular, data are consumed on the fly and data may expire. Stream reasoning, a combination of stream processing and semantic reasoning, has emerged with the vision of providing "smart" processing of streaming data. C-SPARQLmore » is a prominent stream reasoning system that handles semantic (RDF) data streams. Many stream reasoning systems including C-SPARQL use a sliding window and use data arrival time to evict data. For data streams that include expiration times, a simple arrival time scheme is inadequate if the window size does not match the expiration period. In this paper, we propose a cache-enabled, order-aware, ontology-based stream reasoning framework. This framework consumes RDF streams with expiration timestamps assigned by the streaming source. Our framework utilizes both arrival and expiration timestamps in its cache eviction policies. In addition, we introduce the notion of "semantic importance" which aims to address the relevance of data to the expected reasoning, thus enabling the eviction algorithms to be more context- and reasoning-aware when choosing what data to maintain for question answering. We evaluate this framework by implementing three different prototypes and utilizing five metrics. The trade-offs of deploying the proposed framework are also discussed.« less

A comparison study on microwave-assisted extraction of Artemisia sphaerocephala polysaccharides with conventional method: Molecule structure and antioxidant activities evaluation.

PubMed

Wang, Junlong; Zhang, Ji; Wang, Xiaofang; Zhao, Baotang; Wu, Yiqian; Yao, Jian

2009-12-01

The conventional extraction methods for polysaccharides were time-consuming, laborious and energy-consuming. Microwave-assisted extraction (MAE) technique was employed for the extraction of Artemisia sphaerocephala polysaccharides (ASP), which is a traditional Chinese food. The extracting parameters were optimized by Box-Behnken design. In microwave heating process, a decrease in molecular weight (M(w)) was detected in SEC-LLS measurement. A d(f) value of 2.85 indicated ASP using MAE exhibited as a sphere conformation of branched clusters in aqueous solution. Furthermore, it showed stronger antioxidant activities compared with hot water extraction. The data obtained showed that the molecular weights played a more important role in antioxidant activities.

Optimal nonlinear information processing capacity in delay-based reservoir computers

NASA Astrophysics Data System (ADS)

Grigoryeva, Lyudmila; Henriques, Julie; Larger, Laurent; Ortega, Juan-Pablo

2015-09-01

Reservoir computing is a recently introduced brain-inspired machine learning paradigm capable of excellent performances in the processing of empirical data. We focus in a particular kind of time-delay based reservoir computers that have been physically implemented using optical and electronic systems and have shown unprecedented data processing rates. Reservoir computing is well-known for the ease of the associated training scheme but also for the problematic sensitivity of its performance to architecture parameters. This article addresses the reservoir design problem, which remains the biggest challenge in the applicability of this information processing scheme. More specifically, we use the information available regarding the optimal reservoir working regimes to construct a functional link between the reservoir parameters and its performance. This function is used to explore various properties of the device and to choose the optimal reservoir architecture, thus replacing the tedious and time consuming parameter scannings used so far in the literature.

Optimal nonlinear information processing capacity in delay-based reservoir computers.

PubMed

Grigoryeva, Lyudmila; Henriques, Julie; Larger, Laurent; Ortega, Juan-Pablo

2015-09-11

Reservoir computing is a recently introduced brain-inspired machine learning paradigm capable of excellent performances in the processing of empirical data. We focus in a particular kind of time-delay based reservoir computers that have been physically implemented using optical and electronic systems and have shown unprecedented data processing rates. Reservoir computing is well-known for the ease of the associated training scheme but also for the problematic sensitivity of its performance to architecture parameters. This article addresses the reservoir design problem, which remains the biggest challenge in the applicability of this information processing scheme. More specifically, we use the information available regarding the optimal reservoir working regimes to construct a functional link between the reservoir parameters and its performance. This function is used to explore various properties of the device and to choose the optimal reservoir architecture, thus replacing the tedious and time consuming parameter scannings used so far in the literature.

Use of automated rendezvous trajectory planning to improve spacecraft operations efficiency

NASA Technical Reports Server (NTRS)

Mulder, Tom A.

1991-01-01

The current planning process for space shuttle rendezvous with a second Earth-orbiting vehicle is time consuming and costly. It is a labor-intensive, manual process performed pre-mission with the aid of specialized maneuver processing tools. Real-time execution of a rendezvous plan must closely follow a predicted trajectory, and targeted solutions leading up to the terminal phase are computed on the ground. Despite over 25 years of Gemini, Apollo, Skylab, and shuttle vehicle-to-vehicle rendezvous missions flown to date, rendezvous in Earth orbit still requires careful monitoring and cannot be taken for granted. For example, a significant trajectory offset was experienced during terminal phase rendezvous of the STS-32 Long Duration Exposure Facility retrieval mission. Several improvements can be introduced to the present rendezvous planning process to reduce costs, produce more fuel-efficient profiles, and increase the probability of mission success.

Accelerating Biomedical Signal Processing Using GPU: A Case Study of Snore Sound Feature Extraction.

PubMed

Guo, Jian; Qian, Kun; Zhang, Gongxuan; Xu, Huijie; Schuller, Björn

2017-12-01

The advent of 'Big Data' and 'Deep Learning' offers both, a great challenge and a huge opportunity for personalised health-care. In machine learning-based biomedical data analysis, feature extraction is a key step for 'feeding' the subsequent classifiers. With increasing numbers of biomedical data, extracting features from these 'big' data is an intensive and time-consuming task. In this case study, we employ a Graphics Processing Unit (GPU) via Python to extract features from a large corpus of snore sound data. Those features can subsequently be imported into many well-known deep learning training frameworks without any format processing. The snore sound data were collected from several hospitals (20 subjects, with 770-990 MB per subject - in total 17.20 GB). Experimental results show that our GPU-based processing significantly speeds up the feature extraction phase, by up to seven times, as compared to the previous CPU system.

Optimal nonlinear information processing capacity in delay-based reservoir computers

PubMed Central

Grigoryeva, Lyudmila; Henriques, Julie; Larger, Laurent; Ortega, Juan-Pablo

2015-01-01

Reservoir computing is a recently introduced brain-inspired machine learning paradigm capable of excellent performances in the processing of empirical data. We focus in a particular kind of time-delay based reservoir computers that have been physically implemented using optical and electronic systems and have shown unprecedented data processing rates. Reservoir computing is well-known for the ease of the associated training scheme but also for the problematic sensitivity of its performance to architecture parameters. This article addresses the reservoir design problem, which remains the biggest challenge in the applicability of this information processing scheme. More specifically, we use the information available regarding the optimal reservoir working regimes to construct a functional link between the reservoir parameters and its performance. This function is used to explore various properties of the device and to choose the optimal reservoir architecture, thus replacing the tedious and time consuming parameter scannings used so far in the literature. PMID:26358528

Porting of the transfer-matrix method for multilayer thin-film computations on graphics processing units

NASA Astrophysics Data System (ADS)

Limmer, Steffen; Fey, Dietmar

2013-07-01

Thin-film computations are often a time-consuming task during optical design. An efficient way to accelerate these computations with the help of graphics processing units (GPUs) is described. It turned out that significant speed-ups can be achieved. We investigate the circumstances under which the best speed-up values can be expected. Therefore we compare different GPUs among themselves and with a modern CPU. Furthermore, the effect of thickness modulation on the speed-up and the runtime behavior depending on the input data is examined.

Next generation data harmonization

NASA Astrophysics Data System (ADS)

Armstrong, Chandler; Brown, Ryan M.; Chaves, Jillian; Czerniejewski, Adam; Del Vecchio, Justin; Perkins, Timothy K.; Rudnicki, Ron; Tauer, Greg

2015-05-01

Analysts are presented with a never ending stream of data sources. Often, subsets of data sources to solve problems are easily identified but the process to align data sets is time consuming. However, many semantic technologies do allow for fast harmonization of data to overcome these problems. These include ontologies that serve as alignment targets, visual tools and natural language processing that generate semantic graphs in terms of the ontologies, and analytics that leverage these graphs. This research reviews a developed prototype that employs all these approaches to perform analysis across disparate data sources documenting violent, extremist events.

Evaluation of Reaction Cross Section Data Used for Thin Layer Activation Technique

NASA Astrophysics Data System (ADS)

Ditrói, F.; Takács, S.; Tárkányi, F.

2005-05-01

Thin layer activation (TLA) is a widely used nuclear method to investigate and control the loss of material during wear, corrosion and erosion processes. The process requires knowledge of depth profiles of the investigated radioisotopes produced by charged particle bombardment. The depth distribution of the activity can be determined with direct, very time-consuming step by step measurement or by calculation from reliable cross section, stopping power and sample composition data. These data were checked experimentally at several points performing only a couple of measurements.

Evaluation of Reaction Cross Section Data Used for Thin Layer Activation Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ditroi, F.; Takacs, S.; Tarkanyi, F.

2005-05-24

Thin layer activation (TLA) is a widely used nuclear method to investigate and control the loss of material during wear, corrosion and erosion processes. The process requires knowledge of depth profiles of the investigated radioisotopes produced by charged particle bombardment. The depth distribution of the activity can be determined with direct, very time-consuming step by step measurement or by calculation from reliable cross section, stopping power and sample composition data. These data were checked experimentally at several points performing only a couple of measurements.

Challenging Common Sense: Cases of School Reform for Learning Community under an International Cooperation Project in Bac Giang Province, Vietnam

ERIC Educational Resources Information Center

Saito, Eisuke; Tsukui, Atsushi

2008-01-01

This paper aims to discuss the challenges in the process of building a learning community in Vietnamese primary schools. Five lessons emerge from the cases. First, changing teachers' beliefs is time-consuming. Second, because of the reluctance of teachers to change, large-scale delivery of the educational project should be critically revisited…

Development and evaluation of a dynamic web-based application.

PubMed

Hsieh, Yichuan; Brennan, Patricia Flatley

2007-10-11

Traditional consumer health informatics (CHI) applications that were developed for lay public on the Web were commonly written in a Hypertext Markup Language (HTML). As genetics knowledge rapidly advances and requires updating information in a timely fashion, a different content structure is therefore needed to facilitate information delivery. This poster will present the process of developing a dynamic database-driven Web CHI application.

Automatic Short Essay Scoring Using Natural Language Processing to Extract Semantic Information in the Form of Propositions. CRESST Report 831

ERIC Educational Resources Information Center

Kerr, Deirdre; Mousavi, Hamid; Iseli, Markus R.

2013-01-01

The Common Core assessments emphasize short essay constructed-response items over multiple-choice items because they are more precise measures of understanding. However, such items are too costly and time consuming to be used in national assessments unless a way to score them automatically can be found. Current automatic essay-scoring techniques…

Performance Assessment of the Masses in 30 Seconds or Less

ERIC Educational Resources Information Center

Dunbar, Laura

2012-01-01

Performance assessment does not have to be a time-consuming ordeal; it is a great way to assess our students' skills. It is essential to create a rubric that is simple, quick, and objective. This article discusses the process of creating a rubric as well as showing a rubric used by the author in her general music classroom for several years.…