Tsunami Detection by High Frequency Radar Beyond the Continental Shelf: II. Extension of Time Correlation Algorithm and Validation on Realistic Case Studies

NASA Astrophysics Data System (ADS)

Grilli, Stéphan T.; Guérin, Charles-Antoine; Shelby, Michael; Grilli, Annette R.; Moran, Patrick; Grosdidier, Samuel; Insua, Tania L.

2017-08-01

In past work, tsunami detection algorithms (TDAs) have been proposed, and successfully applied to offline tsunami detection, based on analyzing tsunami currents inverted from high-frequency (HF) radar Doppler spectra. With this method, however, the detection of small and short-lived tsunami currents in the most distant radar ranges is challenging due to conflicting requirements on the Doppler spectra integration time and resolution. To circumvent this issue, in Part I of this work, we proposed an alternative TDA, referred to as time correlation (TC) TDA, that does not require inverting currents, but instead detects changes in patterns of correlations of radar signal time series measured in pairs of cells located along the main directions of tsunami propagation (predicted by geometric optics theory); such correlations can be maximized when one signal is time-shifted by the pre-computed long wave propagation time. We initially validated the TC-TDA based on numerical simulations of idealized tsunamis in a simplified geometry. Here, we further develop, extend, and apply the TC algorithm to more realistic tsunami case studies. These are performed in the area West of Vancouver Island, BC, where Ocean Networks Canada recently deployed a HF radar (in Tofino, BC), to detect tsunamis from far- and near-field sources, up to a 110 km range. Two case studies are considered, both simulated using long wave models (1) a far-field seismic, and (2) a near-field landslide, tsunami. Pending the availability of radar data, a radar signal simulator is parameterized for the Tofino HF radar characteristics, in particular its signal-to-noise ratio with range, and combined with the simulated tsunami currents to produce realistic time series of backscattered radar signal from a dense grid of cells. Numerical experiments show that the arrival of a tsunami causes a clear change in radar signal correlation patterns, even at the most distant ranges beyond the continental shelf, thus making an early tsunami detection possible with the TC-TDA. Based on these results, we discuss how the new algorithm could be combined with standard methods proposed earlier, based on a Doppler analysis, to develop a new tsunami detection system based on HF radar data, that could increase warning time. This will be the object of future work, which will be based on actual, rather than simulated, radar data.

An FPGA-Based WASN for Remote Real-Time Monitoring of Endangered Species: A Case Study on the Birdsong Recognition of Botaurus stellaris

PubMed Central

Hervás, Marcos; Alsina-Pagès, Rosa Ma; Alías, Francesc; Salvador, Martí

2017-01-01

Fast environmental variations due to climate change can cause mass decline or even extinctions of species, having a dramatic impact on the future of biodiversity. During the last decade, different approaches have been proposed to track and monitor endangered species, generally based on costly semi-automatic systems that require human supervision adding limitations in coverage and time. However, the recent emergence of Wireless Acoustic Sensor Networks (WASN) has allowed non-intrusive remote monitoring of endangered species in real time through the automatic identification of the sound they emit. In this work, an FPGA-based WASN centralized architecture is proposed and validated on a simulated operation environment. The feasibility of the architecture is evaluated in a case study designed to detect the threatened Botaurus stellaris among other 19 cohabiting birds species in The Parc Natural dels Aiguamolls de l’Empordà, showing an averaged recognition accuracy of 91% over 2h 55’ of representative data. The FPGA-based feature extraction implementation allows the system to process data from 30 acoustic sensors in real time with an affordable cost. Finally, several open questions derived from this research are discussed to be considered for future works. PMID:28594373

[Return to work management of people with temporary disability].

PubMed

Okreglicka, Małgorzata

2011-01-01

There is a large and growing body of scientific evidence that return to work usually provides significant overall health benefit, and staying off work needlessly results in poorer overall health outcomes. Thus, employers, employees (patients), and insurers all benefit from individuals returning to work in usual time periods. Disability duration guidelines can be an important tool helping the injured workers to get back on the job. The return to work process needs to be accepted by all parties (physicians, employees, employers, insurers) as defensible, fair and evidence-based. "The medical disability advisor--Workplace guidelines for disability duration" by Presley Reed is the backbone of communication, understanding and measurement in case management programs, having great impact on many parties and steps during a case life cycle.

Excessive work and risk of haemorrhagic stroke: a nationwide case-control study.

PubMed

Kim, Beom Joon; Lee, Seung-Hoon; Ryu, Wi-Sun; Kim, Chi Kyung; Chung, Jong-Won; Kim, Dohoung; Park, Hong-Kyun; Bae, Hee-Joon; Park, Byung-Joo; Yoon, Byung-Woo

2013-10-01

Adverse effect of excessive work on health has been suggested previously, but it was not documented in cerebrovascular diseases. The authors investigated whether excessive working conditions would associate with increased risk of haemorrhagic stroke. A nationwide matched case-control study database, which contains 940 cases of incident haemorrhagic stroke (498 intracerebral haemorrhages and 442 sub-arachnoid haemorrhages) with 1880 gender- and age- (± 5-year) matched controls, was analysed. Work-related information based on the regular job situation, including type of occupation, regular working time, duration of strenuous activity during regular work and shift work, was gathered through face-to-face interviews. Conditional logistic regression analyses were used for the multivariable analyses. Compared with white-collar workers, blue-collar workers had a higher risk for haemorrhagic stroke (odds ratio, 1.33 [95% confidence interval, 1.06-1.66]). Longer regular working time was associated with increased risk of haemorrhagic stroke [odds ratio, 1.38 (95% confidence interval, 1.05-1.81) for 8-12 h/day; odds ratio, 1.95 (95% confidence interval, 1.33-2.86) for ≥ 13 h/day; compared with ≤ 4 h/day]. Exposure to ≥ 8 h/week of strenuous activity also associated haemorrhagic stroke risk [odds ratio, 1.61 (95% confidence interval, 1.26-2.05); compared with no strenuous activity]. Shift work was not associated with haemorrhagic stroke (P = 0.98). Positive associations between working condition indices and haemorrhagic stroke risk were consistent regardless of haemorrhagic stroke sub-types and current employment status. Blue-collar occupation, longer regular working time and extended duration of strenuous activity during work may relate to an increased risk of haemorrhagic stroke. © 2012 The Authors. International Journal of Stroke © 2012 World Stroke Organization.

[Morbidity caused by industrial accidents in a health zone].

PubMed

Cruzado Quevedo, J; Sánchez Sánchez, J A; Lázaro Gómez, M J; Moreno Pina, J P; Alvarez Orcajada, M J; Cazorla González, M A

1992-05-01

The aim of the present study is to discover the morbidity produced by workplace accidents among the earning population of Molina de Segura Health Area. This was a descriptive crossover study. Site. The study was carried out in the Primary Care framework, in the Molina de Segura Health Area and with the collaboration of the Labour Health Unit of Insalud-Murcia. Over a year a total of 774 cases of time off work due to workplace accidents, out of a total of 9,302 workers, were examined. 679 cases of workers resident in Molina de Segura were included in the study, whose time-off dates fell between July 1, 1989 and June 30, 1990 and where the company for which they worked was based or had its trading name located in Molina. Of the total cases of time off work studied, 539 (79.4%) were men and 140 (20.6%) were women. The pathologies most often found were "blows, bruisings and crushings" (22.8%), "wounds and cuts" (16.8%), "back pain" (10.5%), "strains" (9.4%) and "fractures" (4.5%). A statistically significant association was found between being "a man" and "back pain"; and "a woman" and "sprains". The predominant pathologies among workplace accidents are of a less serious nature. Some pathologies owing to workplace accidents are mistakenly referred to the health services as ordinary illness. There is insufficient compliance by health professionals with filling in the forms for time off work and return to work.

The Cultural and Intercultural Identities of Transnational English Teachers: Two Case Studies from the Americas

ERIC Educational Resources Information Center

Menard-Warwick, Julia

2008-01-01

This article presents case studies of two long-time English language teachers: a California English as a second language instructor originally from Brazil, and a Chilean English as a foreign language teacher who worked for many years in the United States before returning home. Based on interview and classroom observation data, this research…

78 FR 18865 - Defense Federal Acquisition Regulation Supplement: Proposal Adequacy Checklist (DFARS Case 2011...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

..., applicable CLIN, Work Breakdown Structure, rationale for estimate, applicable history, and time-phasing... price adjustments, not just those based on indices. Checklist item 45 (final rule item 35) is modified to read ``If the offeror is proposing Performance-Based Payments did the offeror comply with FAR...

Using vignettes to assess contributions to the work of addressing child mental health problems in primary care.

PubMed

Wissow, Lawrence S; Zafar, Waleed; Fothergill, Kate; Ruble, Anne; Slade, Eric

2016-01-22

To further efforts to integrate mental health and primary care, this study develops a novel approach to quantifying the amount and sources of work involved in shifting care for common mental health problems to pediatric primary care providers. Email/web-based survey of a convenience sample (n = 58) of Maryland pediatricians (77% female, 58% at their site 10 or more years; 44% in private practice, 52 % urban, 48 % practicing with a co-located mental health provider). Participants were asked to review 11 vignettes, which described primary care management of child/youth mental health problems, and rate them on an integer-based ordinal scale for the overall amount of work involved compared to a 12th reference vignette describing an uncomplicated case of ADHD. Respondents were also asked to indicate factors (time, effort, stress) accounting for their ratings. Vignettes presented combinations of three diagnoses (ADHD, anxiety, and depression) and three factors (medical co-morbidity, psychiatric co-morbidity, and difficult families) reported to complicate mental health care. The reference case was pre-assigned a work value of 2. Estimates of the relationship of diagnosis and complicating factors with workload were obtained using linear regression, with random effects at the respondent level. The 58 pediatricians gave 593 vignette responses. Depression was associated with a 1.09 unit (about 50%) increase in work (95% CL .94, 1.25), while anxiety did not differ significantly from the reference case of uncomplicated ADHD (p = .28). Although all three complicating factors increased work ratings compared with the reference case, family complexity and psychiatric co-morbidity did so the most (.87 and 1.07 units, respectively, P < .001) while medical co-morbidity increased it the least (.44 units, p < .001). Factors most strongly associated with increased overall work were physician time, physician mental effort, and stress; those least strongly associated were staff time, physician physical effort, and malpractice risk. Pediatricians working with co-located mental health providers gave higher work ratings than did those without co-located staff. Both diagnosis and cross-diagnosis complicating factors contribute to the work involved in providing mental health services in primary care. Vignette studies may facilitate understanding which mental health services can be most readily incorporated into primary care as it is presently structured and help guide the design of training programs and other implementation strategies.

"I Want an Education": Two Case Studies of Working-Class Ambition and Ambivalence in Further and Higher Education

ERIC Educational Resources Information Center

Morrison, Andrew

2010-01-01

Using data from in-depth individual interviews, this article discusses the educational experiences and ambitions of two young working-class full-time female students. The two studies are derived from a wider investigation into student post-16 educational experiences and decision-making, based on a sample of students and staff of an Advanced…

Distributed environmental control

NASA Technical Reports Server (NTRS)

Cleveland, Gary A.

1992-01-01

We present an architecture of distributed, independent control agents designed to work with the Computer Aided System Engineering and Analysis (CASE/A) simulation tool. CASE/A simulates behavior of Environmental Control and Life Support Systems (ECLSS). We describe a lattice of agents capable of distributed sensing and overcoming certain sensor and effector failures. We address how the architecture can achieve the coordinating functions of a hierarchical command structure while maintaining the robustness and flexibility of independent agents. These agents work between the time steps of the CASE/A simulation tool to arrive at command decisions based on the state variables maintained by CASE/A. Control is evaluated according to both effectiveness (e.g., how well temperature was maintained) and resource utilization (the amount of power and materials used).

Investigating work-related neoplasia associated with solar radiation.

PubMed

Turner, S; Forman, S D; McNamee, R; Wilkinson, S M; Agius, R

2015-01-01

Both solar and non-solar exposures associated with occupation and work tasks have been reported as skin carcinogens. In the UK, there are well-established surveillance schemes providing relevant information, including when exposures took place, occupation, location of work and dates of symptom onset and diagnosis. To add to the evidence on work-related skin neoplasia, including causal agents, geographical exposure and time lag between exposure and diagnosis. This study investigated incident case reports of occupational skin disease originating from clinical specialists in dermatology reporting to a UK-wide surveillance scheme (EPIDERM) by analysing case reports of skin neoplasia from 1996 to 2012 in terms of diagnosis, employment, suspected causal agent and symptom onset. The suspected causal agent was 'sun/sunlight/ultraviolet light' in 99% of the reported work-related skin neoplasia cases. Most cases reported (91%) were in males, and the majority (62%) were aged over 65 at the time of reporting. More detailed information on exposure was available for 42% of the cases, with the median time from exposure to symptom onset ranging from 44 (melanoma) to 57 (squamous cell carcinoma) years. Irrespective of diagnostic category, the median duration of exposure to 'sun/sunlight/ultraviolet light' appeared longer where exposures occurred in the UK (range 39-51 years) rather than outside the UK (range 2.5-6.5 years). It is important to provide effective information about skin protection to workers exposed to solar radiation, especially to outdoor workers based outside the UK. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Epidemiology of occupational hypersensitivity pneumonitis; reports from the SWORD scheme in the UK from 1996 to 2015

PubMed Central

Barber, C M; Wiggans, R E; Carder, M; Agius, R

2017-01-01

Objective To estimate the reported incidence of occupational hypersensitivity pneumonitis (OHP) in the UK and to consider whether the pattern of attributed causation has changed over time. Methods All cases of OHP reported to the SWORD scheme between January 1996 and December 2015 were classified into 1 of 10 categories of the suspected agent. Cases were grouped into four 5-year time periods to examine any changing pattern in incidence or suspected causation. For each time period, the annual incidence was calculated using the estimated number of reported cases and the working population of the UK. Results Between 1996 and 2015, there were 202 actual cases of OHP reported to SWORD, equating to an estimated 818 cases, when adjusting for the sampling ratio. Over this period, the annual UK incidence was 1.4 per million workers. The mean (SD) age of reported cases was 52 (13) years, and cases were four-times more likely to be men than women. Over the study period, there was a fall in the proportion of cases reported to be due to agricultural exposures (44–12%), and an increase in cases due to metalworking fluids (MWFs, 2–45%). Conclusions Over the last 20 years, the incidence of OHP in the UK has been ∼1–2 cases per million workers per year. Working with water-based MWFs is now the most commonly suspected causative exposure for OHP cases reported to the SWORD scheme in the UK. PMID:27919062

Design of Composite Structures Using Knowledge-Based and Case Based Reasoning

NASA Technical Reports Server (NTRS)

Lambright, Jonathan Paul

1996-01-01

A method of using knowledge based and case based reasoning to assist designers during conceptual design tasks of composite structures was proposed. The cooperative use of heuristics, procedural knowledge, and previous similar design cases suggests a potential reduction in design cycle time and ultimately product lead time. The hypothesis of this work is that the design process of composite structures can be improved by using Case-Based Reasoning (CBR) and Knowledge-Based (KB) reasoning in the early design stages. The technique of using knowledge-based and case-based reasoning facilitates the gathering of disparate information into one location that is easily and readily available. The method suggests that the inclusion of downstream life-cycle issues into the conceptual design phase reduces potential of defective, and sub-optimal composite structures. Three industry experts were interviewed extensively. The experts provided design rules, previous design cases, and test problems. A Knowledge Based Reasoning system was developed using the CLIPS (C Language Interpretive Procedural System) environment and a Case Based Reasoning System was developed using the Design Memory Utility For Sharing Experiences (MUSE) xviii environment. A Design Characteristic State (DCS) was used to document the design specifications, constraints, and problem areas using attribute-value pair relationships. The DCS provided consistent design information between the knowledge base and case base. Results indicated that the use of knowledge based and case based reasoning provided a robust design environment for composite structures. The knowledge base provided design guidance from well defined rules and procedural knowledge. The case base provided suggestions on design and manufacturing techniques based on previous similar designs and warnings of potential problems and pitfalls. The case base complemented the knowledge base and extended the problem solving capability beyond the existence of limited well defined rules. The findings indicated that the technique is most effective when used as a design aid and not as a tool to totally automate the composites design process. Other areas of application and implications for future research are discussed.

Design considerations for case series models with exposure onset measurement error.

PubMed

Mohammed, Sandra M; Dalrymple, Lorien S; Sentürk, Damla; Nguyen, Danh V

2013-02-28

The case series model allows for estimation of the relative incidence of events, such as cardiovascular events, within a pre-specified time window after an exposure, such as an infection. The method requires only cases (individuals with events) and controls for all fixed/time-invariant confounders. The measurement error case series model extends the original case series model to handle imperfect data, where the timing of an infection (exposure) is not known precisely. In this work, we propose a method for power/sample size determination for the measurement error case series model. Extensive simulation studies are used to assess the accuracy of the proposed sample size formulas. We also examine the magnitude of the relative loss of power due to exposure onset measurement error, compared with the ideal situation where the time of exposure is measured precisely. To facilitate the design of case series studies, we provide publicly available web-based tools for determining power/sample size for both the measurement error case series model as well as the standard case series model. Copyright © 2012 John Wiley & Sons, Ltd.

The Relationship between Musculoskeletal Symptoms and Work-related Risk Factors in Hotel Workers.

PubMed

Lee, Jin Woo; Lee, Ju Jong; Mun, Hyeon Je; Lee, Kyung-Jae; Kim, Joo Ja

2013-10-11

To identify work-related musculoskeletal symptoms and any associated work-related risk factors, focusing on structural labor factors among hotel workers. A total of 1,016 hotel workers (620 men and 396 women) were analyzed. The questionnaire surveyed participants' socio-demographics, health-related behaviors, job-related factors, and work-related musculoskeletal symptoms. Work-related musculoskeletal symptoms were assessed using the Nordic musculoskeletal questionnaire. All analyses were stratified by gender, and multiple logistic regression modeling was used to determine associations between work-related musculoskeletal symptoms and work-related risk factors. The risk of developing work-related musculoskeletal symptoms was 1.9 times higher among male workers in the kitchen department than males in the room department (OR = 1.92, 95% CI = 1.03-3.79), and 2.5 times higher among male workers with lower sleep satisfaction than those with higher sleep satisfaction (OR = 2.52, 95% CI = 1.57-4.04). All of the aforementioned cases demonstrated a statistically significant association with work-related musculoskeletal symptoms. Moreover, the risk of developing work-related musculoskeletal symptoms was 3.3 times higher among female workers aged between 30 and 34 than those aged 24 or younger (OR = 3.32, 95% CI = 1.56-7.04); 0.3 times higher among females in the back office department than those in the room department (OR = 0.34, 95% CI = 0.12-0.91); 1.6 times higher among females on shift schedules than those who were not (OR = 1.60, 95% CI = 1.02-2.59); 1.8 times higher among females who performed more intensive work than those who performed less intensive work (OR = 1.88, 95% CI = 1.17-3.02), and; 2.1 times higher among females with lower sleep satisfaction than those with higher sleep satisfaction (OR = 2.17, 95% CI = 1.34-3.50). All of the aforementioned cases also displayed a statistically significant association with work-related musculoskeletal symptoms. This study focused on structural risk factors in the working environment, such as the gender-based division of labor, shift work and labor intensity, that demonstrated a statistically significant correlation with the work-related musculoskeletal symptoms of hotel workers. Both men and women reported different prevalence rates of work-related musculoskeletal symptoms among different departments. This could indicate that a gender-based division of labor produces different ergonomic risk factors for each gender group. However, only females displayed a statistically significant correlation between shift work and labor intensity and musculoskeletal symptoms. Thus, minimizing ergonomic risk factors alone does not suffice to effectively prevent musculoskeletal diseases among hotel workers. Instead, work assignments should be based on gender, department, working hours and work intensity should be adjusted to address multi-dimensional musculoskeletal risk factors. In addition, an approach that seeks to minimize shift work is needed to reduce the incidence of musculoskeletal disorders.

The Relationship between Musculoskeletal Symptoms and Work-related Risk Factors in Hotel Workers

PubMed Central

2013-01-01

Objectives To identify work-related musculoskeletal symptoms and any associated work-related risk factors, focusing on structural labor factors among hotel workers. Methods A total of 1,016 hotel workers (620 men and 396 women) were analyzed. The questionnaire surveyed participants’ socio-demographics, health-related behaviors, job-related factors, and work-related musculoskeletal symptoms. Work-related musculoskeletal symptoms were assessed using the Nordic musculoskeletal questionnaire. All analyses were stratified by gender, and multiple logistic regression modeling was used to determine associations between work-related musculoskeletal symptoms and work-related risk factors. Results The risk of developing work-related musculoskeletal symptoms was 1.9 times higher among male workers in the kitchen department than males in the room department (OR = 1.92, 95% CI = 1.03-3.79), and 2.5 times higher among male workers with lower sleep satisfaction than those with higher sleep satisfaction (OR = 2.52, 95% CI = 1.57-4.04). All of the aforementioned cases demonstrated a statistically significant association with work-related musculoskeletal symptoms. Moreover, the risk of developing work-related musculoskeletal symptoms was 3.3 times higher among female workers aged between 30 and 34 than those aged 24 or younger (OR = 3.32, 95% CI = 1.56-7.04); 0.3 times higher among females in the back office department than those in the room department (OR = 0.34, 95% CI = 0.12-0.91); 1.6 times higher among females on shift schedules than those who were not (OR = 1.60, 95% CI = 1.02-2.59); 1.8 times higher among females who performed more intensive work than those who performed less intensive work (OR = 1.88, 95% CI = 1.17-3.02), and; 2.1 times higher among females with lower sleep satisfaction than those with higher sleep satisfaction (OR = 2.17, 95% CI = 1.34-3.50). All of the aforementioned cases also displayed a statistically significant association with work-related musculoskeletal symptoms. Conclusion This study focused on structural risk factors in the working environment, such as the gender-based division of labor, shift work and labor intensity, that demonstrated a statistically significant correlation with the work-related musculoskeletal symptoms of hotel workers. Both men and women reported different prevalence rates of work-related musculoskeletal symptoms among different departments. This could indicate that a gender-based division of labor produces different ergonomic risk factors for each gender group. However, only females displayed a statistically significant correlation between shift work and labor intensity and musculoskeletal symptoms. Thus, minimizing ergonomic risk factors alone does not suffice to effectively prevent musculoskeletal diseases among hotel workers. Instead, work assignments should be based on gender, department, working hours and work intensity should be adjusted to address multi-dimensional musculoskeletal risk factors. In addition, an approach that seeks to minimize shift work is needed to reduce the incidence of musculoskeletal disorders. PMID:24472690

Alternative approaches to analytical designs in occupational injury epidemiology.

PubMed

Mittleman, M A; Maldonado, G; Gerberich, S G; Smith, G S; Sorock, G S

1997-08-01

In this paper, we discuss the theoretical framework upon which observational studies of occupational injuries are based. Following a general description of how causal effects are estimated, the challenges faced by researchers working in this area are outlined, with an emphasis on case-control studies. These challenges include defining the at-risk period for workers whose tasks change over time and whose hazard period may be very brief, evaluating the underreporting of both exposures and injuries, and considering the effects of multiple injuries per individual on study design and data analysis. We review both the theoretical and practical considerations in the design and conduct of traditional case-control studies, based on the collection of individual level data, as well as other approaches, such as using information culled from administrative and descriptive databases, and case-control studies in which the plant or work site is the unit of analysis. The case-crossover design is also reviewed and its utility for reducing confounding due to differences between individuals by self-matching is highlighted. While this design has not yet been applied to the work setting, its potential for increasing our understanding of the causes of acute-onset occupational injuries seems promising. Finally, a variety of hybrid designs are discussed, including combinations of case-control, case-crossover, and cohort designs.

Computer aided segmentation of kidneys using locally shape constrained deformable models on CT images

NASA Astrophysics Data System (ADS)

Erdt, Marius; Sakas, Georgios

2010-03-01

This work presents a novel approach for model based segmentation of the kidney in images acquired by Computed Tomography (CT). The developed computer aided segmentation system is expected to support computer aided diagnosis and operation planning. We have developed a deformable model based approach based on local shape constraints that prevents the model from deforming into neighboring structures while allowing the global shape to adapt freely to the data. Those local constraints are derived from the anatomical structure of the kidney and the presence and appearance of neighboring organs. The adaptation process is guided by a rule-based deformation logic in order to improve the robustness of the segmentation in areas of diffuse organ boundaries. Our work flow consists of two steps: 1.) a user guided positioning and 2.) an automatic model adaptation using affine and free form deformation in order to robustly extract the kidney. In cases which show pronounced pathologies, the system also offers real time mesh editing tools for a quick refinement of the segmentation result. Evaluation results based on 30 clinical cases using CT data sets show an average dice correlation coefficient of 93% compared to the ground truth. The results are therefore in most cases comparable to manual delineation. Computation times of the automatic adaptation step are lower than 6 seconds which makes the proposed system suitable for an application in clinical practice.

Physical activity levels, sport activities, and risk of acute myocardial infarction: results of the INTERHEART study in China.

PubMed

Cheng, Xiaoru; Li, Wei; Guo, Jin; Wang, Yang; Gu, Hongqiu; Teo, Koon; Liu, Lisheng; Yusuf, Salim

2014-02-01

Physical activity (PA) during leisure time has been inversely associated with cardiovascular disease risk in the Western populations. We evaluated PA at work and leisure time in relation to acute myocardial infarction (AMI) in Chinese population. We conducted a hospital-based case-control study. The cases had first AMI (n = 2909). The controls (n = 2947) were matched to the cases in age and sex. The odds ratios (ORs) of leisure-time PA for strenuous exercise compared to mainly sedentary was 0.74 (95% confidence interval [CI]: 0.61-0.90) and for moderate exercise it was 0.96 (95% CI: 0.85-1.08). Multivariate adjustment did not substantially alter the association. The ORs of work-related PA for heavy PA compared to mainly sedentary was 1.44 (95% CI: 1.06-1.94), for climbing and lifting was 1.00 (95% CI: 0.77-.30), and for walking was 0.90 (95%CI: 0.75-1.07). Leisure-time PA was protective for AMI risk compared to sedentary lifestyles in a population in China.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beltran, C; Kamal, H

Purpose: To provide a multicriteria optimization algorithm for intensity modulated radiation therapy using pencil proton beam scanning. Methods: Intensity modulated radiation therapy using pencil proton beam scanning requires efficient optimization algorithms to overcome the uncertainties in the Bragg peaks locations. This work is focused on optimization algorithms that are based on Monte Carlo simulation of the treatment planning and use the weights and the dose volume histogram (DVH) control points to steer toward desired plans. The proton beam treatment planning process based on single objective optimization (representing a weighted sum of multiple objectives) usually leads to time-consuming iterations involving treatmentmore » planning team members. We proved a time efficient multicriteria optimization algorithm that is developed to run on NVIDIA GPU (Graphical Processing Units) cluster. The multicriteria optimization algorithm running time benefits from up-sampling of the CT voxel size of the calculations without loss of fidelity. Results: We will present preliminary results of Multicriteria optimization for intensity modulated proton therapy based on DVH control points. The results will show optimization results of a phantom case and a brain tumor case. Conclusion: The multicriteria optimization of the intensity modulated radiation therapy using pencil proton beam scanning provides a novel tool for treatment planning. Work support by a grant from Varian Inc.« less

Reimbursement in hospital-based vascular surgery: Physician and practice perspective.

PubMed

Perri, Jennifer L; Zwolak, Robert M; Goodney, Philip P; Rutherford, Gretchen A; Powell, Richard J

2017-07-01

The purpose of this study was to determine change in value of a vascular surgery division to the health care system during 6 years at a hospital-based academic practice and to compare physician vs hospital revenue earned during this period. Total revenue generated by the vascular surgery service line at an academic medical center from 2010 through 2015 was evaluated. Total revenue was measured as the sum of physician (professional) and hospital (technical) net revenue for all vascular-related patient care. Adjustments were made for work performed, case complexity, and inflation. To reflect the effect of these variables, net revenue was indexed to work relative value units (wRVUs), case mix index, and consumer price index, which adjusted for work, case complexity, and inflation, respectively. Differences in physician and hospital net revenue were compared over time. Physician work, measured in RVUs per year, increased by 4%; case complexity, assessed with case mix index, increased by 10% for the 6-year measurement period. Despite stability in payer mix at 64% to 69% Medicare, both physician and hospital vascular-related revenue/wRVU decreased during this period. Unadjusted professional revenue/wRVU declined by 14.1% (P = .09); when considering case complexity, physician revenue/wRVU declined by 20.6% (P = .09). Taking into account both case complexity and inflation, physician revenue declined by 27.0% (P = .04). Comparatively, hospital revenue for vascular surgery services decreased by 13.8% (P = .07) when adjusting for unit work, complexity, and inflation. At medical centers where vascular surgeons are hospital based, vascular care reimbursement decreased substantially from 2010 to 2015 when case complexity and inflation were considered. Physician reimbursement (professional fees) decreased at a significantly greater rate than hospital reimbursement for vascular care. This trend has significant implications for salaried vascular surgeons in hospital-based settings, where the majority of revenue generated by vascular surgery care is the technical component received by the facility. Appropriate care for patients with vascular disease is increasingly resource intensive, and as a corollary, reimbursement levels must reflect this situation if high-quality care is to be maintained. Copyright © 2017 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

An Intelligent E-Learning System Based on Learner Profiling and Learning Resources Adaptation

ERIC Educational Resources Information Center

Tzouveli, Paraskevi; Mylonas, Phivos; Kollias, Stefanos

2008-01-01

Taking advantage of the continuously improving, web-based learning systems plays an important role for self-learning, especially in the case of working people. Nevertheless, learning systems do not generally adapt to learners' profiles. Learners have to spend a lot of time before reaching the learning goal that is compatible with their knowledge…

Effects of seasonal and pandemic influenza on health-related quality of life, work and school absence in England: Results from the Flu Watch cohort study.

PubMed

Fragaszy, Ellen B; Warren-Gash, Charlotte; White, Peter J; Zambon, Maria; Edmunds, William J; Nguyen-Van-Tam, Jonathan S; Hayward, Andrew C

2018-01-01

Estimates of health-related quality of life (HRQoL) and work/school absences for influenza are typically based on medically attended cases or those meeting influenza-like-illness (ILI) case definitions and thus biased towards severe disease. Although community influenza cases are more common, estimates of their effects on HRQoL and absences are limited. To measure quality-adjusted life days and years (QALDs and QALYs) lost and work/school absences among community cases of acute respiratory infections (ARI), ILI and influenza A and B and to estimate community burden of QALY loss and absences from influenza. Flu Watch was a community cohort in England from 2006 to 2011. Participants were followed up weekly. During respiratory illness, they prospectively recorded daily symptoms, work/school absences and EQ-5D-3L data and submitted nasal swabs for RT-PCR influenza testing. Average QALD lost was 0.26, 0.93, 1.61 and 1.84 for ARI, ILI, H1N1pdm09 and influenza B cases, respectively. 40% of influenza A cases and 24% of influenza B cases took time off work/school with an average duration of 3.6 and 2.4 days, respectively. In England, community influenza cases lost 24 300 QALYs in 2010/11 and had an estimated 2.9 million absences per season based on data from 2006/07 to 2009/10. Our QALDs and QALYs lost and work and school absence estimates are lower than previous estimates because we focus on community cases, most of which are mild, may not meet ILI definitions and do not result in healthcare consultations. Nevertheless, they contribute a substantial loss of HRQoL on a population level. © 2017 The Authors. Influenza and Other Respiratory Viruses. Published by John Wiley & Sons Ltd.

An FPGA-Based WASN for Remote Real-Time Monitoring of Endangered Species: A Case Study on the Birdsong Recognition of Botaurus stellaris.

PubMed

Hervás, Marcos; Alsina-Pagès, Rosa Ma; Alías, Francesc; Salvador, Martí

2017-06-08

Fast environmental variations due to climate change can cause mass decline or even extinctions of species, having a dramatic impact on the future of biodiversity. During the last decade, different approaches have been proposed to track and monitor endangered species, generally based on costly semi-automatic systems that require human supervision adding limitations in coverage and time. However, the recent emergence of Wireless Acoustic Sensor Networks (WASN) has allowed non-intrusive remote monitoring of endangered species in real time through the automatic identification of the sound they emit. In this work, an FPGA-based WASN centralized architecture is proposed and validated on a simulated operation environment. The feasibility of the architecture is evaluated in a case study designed to detect the threatened Botaurus stellaris among other 19 cohabiting birds species in The Parc Natural dels Aiguamolls de l'Empord.

Impact of chronic lymphatic filariasis on quantity and quality of productive work among weavers in an endemic village from India.

PubMed

Babu, B V; Swain, B K; Rath, K

2006-05-01

To assess the impact of hydrocele and lymphoedema on the quantity and quality of productive work of weavers. Case-control study in an endemic village in Andhra Pradesh, India. We collected qualitative data on work activities from cases and age- and sex-matched controls through informal discussions and observation. The mean (+/-standard deviation) daily work time of cases was 7.38 h (+/-2.47), significantly less than that of controls (8.17+/-2.41 h). Lost work time was equivalent to around 29 days of work in a year. Gender had significant influence on the mean number of working hours in this occupational group. Most cases could not weave, which is physically demanding, and preferred less strenuous tasks such as spinning, starching, dyeing or sizing. Hard physical labour constitutes 71.5% of total work time among patients and 83.7% in controls. As income also depends on the type of work, cases earn less. Filariasis has an adverse impact on the productivity of weavers, and morbidity management strategies and control programmes need to take this into account.

Numerical study of time domain analogy applied to noise prediction from rotating blades

NASA Astrophysics Data System (ADS)

Fedala, D.; Kouidri, S.; Rey, R.

2009-04-01

Aeroacoustic formulations in time domain are frequently used to model the aerodynamic sound of airfoils, the time data being more accessible. The formulation 1A developed by Farassat, an integral solution of the Ffowcs Williams and Hawkings equation, holds great interest because of its ability to handle surfaces in arbitrary motion. The aim of this work is to study the numerical sensitivity of this model to specified parameters used in the calculation. The numerical algorithms, spatial and time discretizations, and approximations used for far-field acoustic simulation are presented. An approach of quantifying of the numerical errors resulting from implementation of formulation 1A is carried out based on Isom's and Tam's test cases. A helicopter blade airfoil, as defined by Farassat to investigate Isom's case, is used in this work. According to Isom, the acoustic response of a dipole source with a constant aerodynamic load, ρ0c02, is equal to the thickness noise contribution. Discrepancies are observed when the two contributions are computed numerically. In this work, variations of these errors, which depend on the temporal resolution, Mach number, source-observer distance, and interpolation algorithm type, are investigated. The results show that the spline interpolating algorithm gives the minimum error. The analysis is then extended to Tam's test case. Tam's test case has the advantage of providing an analytical solution for the first harmonic of the noise produced by a specific force distribution.

A Python-based interface to examine motions in time series of solar images

NASA Astrophysics Data System (ADS)

Campos-Rozo, J. I.; Vargas Domínguez, S.

2017-10-01

Python is considered to be a mature programming language, besides of being widely accepted as an engaging option for scientific analysis in multiple areas, as will be presented in this work for the particular case of solar physics research. SunPy is an open-source library based on Python that has been recently developed to furnish software tools to solar data analysis and visualization. In this work we present a graphical user interface (GUI) based on Python and Qt to effectively compute proper motions for the analysis of time series of solar data. This user-friendly computing interface, that is intended to be incorporated to the Sunpy library, uses a local correlation tracking technique and some extra tools that allows the selection of different parameters to calculate, vizualize and analyze vector velocity fields of solar data, i.e. time series of solar filtergrams and magnetograms.

Epidemiology of occupational hypersensitivity pneumonitis; reports from the SWORD scheme in the UK from 1996 to 2015.

PubMed

Barber, C M; Wiggans, R E; Carder, M; Agius, R

2017-07-01

To estimate the reported incidence of occupational hypersensitivity pneumonitis (OHP) in the UK and to consider whether the pattern of attributed causation has changed over time. All cases of OHP reported to the SWORD scheme between January 1996 and December 2015 were classified into 1 of 10 categories of the suspected agent. Cases were grouped into four 5-year time periods to examine any changing pattern in incidence or suspected causation. For each time period, the annual incidence was calculated using the estimated number of reported cases and the working population of the UK. Between 1996 and 2015, there were 202 actual cases of OHP reported to SWORD, equating to an estimated 818 cases, when adjusting for the sampling ratio. Over this period, the annual UK incidence was 1.4 per million workers. The mean (SD) age of reported cases was 52 (13) years, and cases were four-times more likely to be men than women. Over the study period, there was a fall in the proportion of cases reported to be due to agricultural exposures (44-12%), and an increase in cases due to metalworking fluids (MWFs, 2-45%). Over the last 20 years, the incidence of OHP in the UK has been ∼1-2 cases per million workers per year. Working with water-based MWFs is now the most commonly suspected causative exposure for OHP cases reported to the SWORD scheme in the UK. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Does Lean healthcare improve patient satisfaction? A mixed-method investigation into primary care.

PubMed

Poksinska, Bozena Bonnie; Fialkowska-Filipek, Malgorzata; Engström, Jon

2017-02-01

Lean healthcare is claimed to contribute to improved patient satisfaction, but there is limited evidence to support this notion. This study investigates how primary-care centres working with Lean define and improve value from the patient's perspective, and how the application of Lean healthcare influences patient satisfaction. This paper contains two qualitative case studies and a quantitative study based on results from the Swedish National Patient Survey. Through the case studies, we investigated how primary-care organisations realised the principle of defining and improving value from the patient's perspective. In the quantitative study, we compared results from the patient satisfaction survey for 23 primary-care centres working with Lean with a control group of 23 care centres not working with Lean. We also analysed changes in patient satisfaction over time. Our case studies reveal that Lean healthcare implementations primarily target efficiency and little attention is paid to the patient's perspective. The quantitative study shows no significantly better results in patient satisfaction for primary-care centres working with Lean healthcare compared with those not working with Lean. Further, care centres working with Lean show no significant improvements in patient satisfaction over time. Lean healthcare implementations seem to have a limited impact on improving patient satisfaction. Care providers need to pay more attention to integrating the patient's perspective in the application of Lean healthcare. Value needs to be defined and value streams need to be improved based on both the knowledge and clinical expertise of care providers, and the preferences and needs of patients. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

The general surgery chief resident operative experience: 23 years of national ACGME case logs.

PubMed

Drake, Frederick Thurston; Horvath, Karen D; Goldin, Adam B; Gow, Kenneth W

2013-09-01

The chief resident (CR) year is a pivotal experience in surgical training. Changes in case volume and diversity may impact the educational quality of this important year. To evaluate changes in operative experience for general surgery CRs. Review of Accreditation Council for Graduate Medical Education case logs from 1989-1990 through 2011-2012 divided into 5 periods. Graduates in period 3 were the last to train with unrestricted work hours; those in period 4 were part of a transition period and trained under both systems; and those in period 5 trained fully under the 80-hour work week. Diversity of cases was assessed based on Accreditation Council for Graduate Medical Education defined categories. Total cases and defined categories were evaluated for changes over time. The average total CR case numbers have fallen (271 in period 1 vs 242 in period 5, P < .001). Total CR cases dropped to their lowest following implementation of the 80-hour work week (236 cases), but rebounded in period 5. The percentage of residents' 5-year operative experience performed as CRs has decreased (30% in period 1 vs 25.6% in period 5, P < .001). Regarding case mix: thoracic, trauma, and vascular cases declined steadily, while alimentary and intra-abdominal operations increased. Recent graduates averaged 80 alimentary and 78 intra-abdominal procedures during their CR years. Compared with period 1, in which these 2 categories represented 47.1% of CR experience, in period 5, they represented 65.2% (P < .001). Endocrine experience has been relatively unchanged. Total CR cases declined especially acutely following implementation of the 80-hour work week but have since rebounded. Chief resident cases contribute less to overall experience, although this proportion stabilized before the 80-hour work week. Case mix has narrowed, with significant increases in alimentary and intra-abdominal cases. Broad-based general surgery training may be jeopardized by reduced case diversity. Chief resident cases are crucial in surgical training and educators should consider these findings as surgical training evolves.

The Case for an Arts-Based Curriculum

ERIC Educational Resources Information Center

Stuht, Amy Colcord; Gates, Janie Yuguchi

2007-01-01

Continuation schools were developed to enable students to continue earning a high school diploma while they worked, often full time, to support themselves and their families. Traditionally, continuation schools were home to poor teachers, narrowed curriculum and an unwelcoming culture. Intuitively, students attending today's continuation schools…

A Model Independent S/W Framework for Search-Based Software Testing

PubMed Central

Baik, Jongmoon

2014-01-01

In Model-Based Testing (MBT) area, Search-Based Software Testing (SBST) has been employed to generate test cases from the model of a system under test. However, many types of models have been used in MBT. If the type of a model has changed from one to another, all functions of a search technique must be reimplemented because the types of models are different even if the same search technique has been applied. It requires too much time and effort to implement the same algorithm over and over again. We propose a model-independent software framework for SBST, which can reduce redundant works. The framework provides a reusable common software platform to reduce time and effort. The software framework not only presents design patterns to find test cases for a target model but also reduces development time by using common functions provided in the framework. We show the effectiveness and efficiency of the proposed framework with two case studies. The framework improves the productivity by about 50% when changing the type of a model. PMID:25302314

Progress Report on the Airborne Composition Standard Variable Name and Time Series Working Groups of the 2017 ESDSWG

NASA Astrophysics Data System (ADS)

Evans, K. D.; Early, A. B.; Northup, E. A.; Ames, D. P.; Teng, W. L.; Olding, S. W.; Krotkov, N. A.; Arctur, D. K.; Beach, A. L., III; Silverman, M. L.

2017-12-01

The role of NASA's Earth Science Data Systems Working Groups (ESDSWG) is to make recommendations relevant to NASA's Earth science data systems from users' experiences and community insight. Each group works independently, focusing on a unique topic. Progress of two of the 2017 Working Groups will be presented. In a single airborne field campaign, there can be several different instruments and techniques that measure the same parameter on one or more aircraft platforms. Many of these same parameters are measured during different airborne campaigns using similar or different instruments and techniques. The Airborne Composition Standard Variable Name Working Group is working to create a list of variable standard names that can be used across all airborne field campaigns in order to assist in the transition to the ICARTT Version 2.0 file format. The overall goal is to enhance the usability of ICARTT files and the search ability of airborne field campaign data. The Time Series Working Group (TSWG) is a continuation of the 2015 and 2016 Time Series Working Groups. In 2015, we started TSWG with the intention of exploring the new OGC (Open Geospatial Consortium) WaterML 2 standards as a means for encoding point-based time series data from NASA satellites. In this working group, we realized that WaterML 2 might not be the best solution for this type of data, for a number of reasons. Our discussion with experts from other agencies, who have worked on similar issues, identified several challenges that we would need to address. As a result, we made the recommendation to study the new TimeseriesML 1.0 standard of OGC as a potential NASA time series standard. The 2016 TSWG examined closely the TimeseriesML 1.0 and, in coordination with the OGC TimeseriesML Standards Working Group, identified certain gaps in TimeseriesML 1.0 that would need to be addressed for the standard to be applicable to NASA time series data. An engineering report was drafted based on the OGC Engineering Report template, describing recommended changes to TimeseriesML 1.0, in the form of use cases. In 2017, we are conducting interoperability experiments to implement the use cases and demonstrate the feasibility and suitability of these modifications for NASA and related user communities. The results will be incorporated into the existing draft engineering report.

Progress Report on the Airborne Composition Standard Variable Name and Time Series Working Groups of the 2017 ESDSWG

NASA Technical Reports Server (NTRS)

Evans, Keith D.; Early, Amanda; Northup, Emily; Ames, Dan; Teng, William; Archur, David; Beach, Aubrey; Olding, Steve; Krotkov, Nickolay A.

2017-01-01

The role of NASA's Earth Science Data Systems Working Groups (ESDSWG) is to make recommendations relevant to NASA's Earth science data systems from users' experiences and community insight. Each group works independently, focusing on a unique topic. Progress of two of the 2017 Working Groups will be presented. In a single airborne field campaign, there can be several different instruments and techniques that measure the same parameter on one or more aircraft platforms. Many of these same parameters are measured during different airborne campaigns using similar or different instruments and techniques. The Airborne Composition Standard Variable Name Working Group is working to create a list of variable standard names that can be used across all airborne field campaigns in order to assist in the transition to the ICARTT Version 2.0 file format. The overall goal is to enhance the usability of ICARTT files and the search ability of airborne field campaign data. The Time Series Working Group (TSWG) is a continuation of the 2015 and 2016 Time Series Working Groups. In 2015, we started TSWG with the intention of exploring the new OGC (Open Geospatial Consortium) WaterML 2 standards as a means for encoding point-based time series data from NASA satellites. In this working group, we realized that WaterML 2 might not be the best solution for this type of data, for a number of reasons. Our discussion with experts from other agencies, who have worked on similar issues, identified several challenges that we would need to address. As a result, we made the recommendation to study the new TimeseriesML 1.0 standard of OGC as a potential NASA time series standard. The 2016 TSWG examined closely the TimeseriesML 1.0 and, in coordination with the OGC TimeseriesML Standards Working Group, identified certain gaps in TimeseriesML 1.0 that would need to be addressed for the standard to be applicable to NASA time series data. An engineering report was drafted based on the OGC Engineering Report template, describing recommended changes to TimeseriesML 1.0, in the form of use cases. In 2017, we are conducting interoperability experiments to implement the use cases and demonstrate the feasibility and suitability of these modifications for NASA and related user communities. The results will be incorporated into the existing draft engineering report.

Local bladder cancer clusters in southeastern Michigan accounting for risk factors, covariates and residential mobility.

PubMed

Jacquez, Geoffrey M; Shi, Chen; Meliker, Jaymie R

2015-01-01

In case control studies disease risk not explained by the significant risk factors is the unexplained risk. Considering unexplained risk for specific populations, places and times can reveal the signature of unidentified risk factors and risk factors not fully accounted for in the case-control study. This potentially can lead to new hypotheses regarding disease causation. Global, local and focused Q-statistics are applied to data from a population-based case-control study of 11 southeast Michigan counties. Analyses were conducted using both year- and age-based measures of time. The analyses were adjusted for arsenic exposure, education, smoking, family history of bladder cancer, occupational exposure to bladder cancer carcinogens, age, gender, and race. Significant global clustering of cases was not found. Such a finding would indicate large-scale clustering of cases relative to controls through time. However, highly significant local clusters were found in Ingham County near Lansing, in Oakland County, and in the City of Jackson, Michigan. The Jackson City cluster was observed in working-ages and is thus consistent with occupational causes. The Ingham County cluster persists over time, suggesting a broad-based geographically defined exposure. Focused clusters were found for 20 industrial sites engaged in manufacturing activities associated with known or suspected bladder cancer carcinogens. Set-based tests that adjusted for multiple testing were not significant, although local clusters persisted through time and temporal trends in probability of local tests were observed. Q analyses provide a powerful tool for unpacking unexplained disease risk from case-control studies. This is particularly useful when the effect of risk factors varies spatially, through time, or through both space and time. For bladder cancer in Michigan, the next step is to investigate causal hypotheses that may explain the excess bladder cancer risk localized to areas of Oakland and Ingham counties, and to the City of Jackson.

The General Surgery Chief Resident Operative Experience

PubMed Central

Drake, Frederick Thurston; Horvath, Karen D.; Goldin, Adam B.; Gow, Kenneth W.

2014-01-01

IMPORTANCE The chief resident (CR) year is a pivotal experience in surgical training. Changes in case volume and diversity may impact the educational quality of this important year. OBJECTIVE To evaluate changes in operative experience for general surgery CRs. DESIGN, SETTING, AND PARTICIPANTS Review of Accreditation Council for Graduate Medical Education case logs from 1989–1990 through 2011–2012 divided into 5 periods. Graduates in period 3 were the last to train with unrestricted work hours; those in period 4 were part of a transition period and trained under both systems; and those in period 5 trained fully under the 80-hour work week. Diversity of cases was assessed based on Accreditation Council for Graduate Medical Education defined categories. MAIN OUTCOMES AND MEASURES Total cases and defined categories were evaluated for changes over time. RESULTS The average total CR case numbers have fallen (271 in period 1 vs 242 in period 5, P < .001). Total CR cases dropped to their lowest following implementation of the 80-hour work week (236 cases), but rebounded in period 5. The percentage of residents’ 5-year operative experience performed as CRs has decreased (30% in period 1 vs 25.6% in period 5, P < .001). Regarding case mix: thoracic, trauma, and vascular cases declined steadily, while alimentary and intra-abdominal operations increased. Recent graduates averaged 80 alimentary and 78 intra-abdominal procedures during their CR years. Compared with period 1, in which these 2 categories represented 47.1% of CR experience, in period 5, they represented 65.2% (P < .001). Endocrine experience has been relatively unchanged. CONCLUSIONS AND RELEVANCE Total CR cases declined especially acutely following implementation of the 80-hour work week but have since rebounded. Chief resident cases contribute less to overall experience, although this proportion stabilized before the 80-hour work week. Case mix has narrowed, with significant increases in alimentary and intra-abdominal cases. Broad-based general surgery training may be jeopardized by reduced case diversity. Chief resident cases are crucial in surgical training and educators should consider these findings as surgical training evolves. PMID:23864049

A descriptive study of work aggravated asthma.

PubMed

Goe, S K; Henneberger, P K; Reilly, M J; Rosenman, K D; Schill, D P; Valiante, D; Flattery, J; Harrison, R; Reinisch, F; Tumpowsky, C; Filios, M S

2004-06-01

Work related asthma (WRA) is one of the most frequently reported occupational lung diseases in a number of industrialised countries. A better understanding of work aggravated asthma (WAA), as well as work related new onset asthma (NOA), is needed to aid in prevention efforts. WAA and NOA in the United States were compared using cases reported to the National Institute for Occupational Safety and Health (NIOSH) from four state Sentinel Event Notification Systems for Occupational Risks (SENSOR) surveillance programmes for 1993-95. A total of 210 WAA cases and 891 NOA cases were reported. WAA cases reported mineral and inorganic dusts as the most common exposure agent, as opposed to NOA cases, in which diisocyanates were reported most frequently. A similar percentage of WAA and NOA cases still experienced breathing problems at the time of the interview or had visited a hospital or emergency room for work related breathing problems. NOA cases were twice as likely to have applied for workers' compensation compared with WAA cases. However, among those who had applied for worker compensation, approximately three-fourths of both WAA and NOA cases had received awards. The services and manufacturing industrial categories together accounted for the majority of both WAA (62%) and NOA (75%) cases. The risk of WAA, measured by average annual rate, was clearly the highest in the public administration (14.2 cases/10(5)) industrial category, while the risk of NOA was increased in both the manufacturing (3.2 cases/10(5)) and public administration (2.9 cases/10(5)) categories. WAA cases reported many of the same adverse consequences as NOA cases. Certain industries were identified as potential targets for prevention efforts based on either the number of cases or the risk of WAA and NOA.

A case-crossover study of transient risk factors influence on occupational injuries: a study protocol based on a review of previous studies.

PubMed

Oesterlund, Anna H; Lander, Flemming; Lauritsen, Jens

2016-10-01

The occupational injury incident rate remains relatively high in the European Union. The case-crossover study gives a unique opportunity to study transient risk factors that normally would be very difficult to approach. Studies like this have been carried out in both America and Asia, but so far no relevant research has been conducted in Europe. Case-crossover studies of occupational injuries were collected from PubMed and Embase and read through. Previous experiences concerning method, exposure and outcome, time-related measurements and construction of the questionnaire were taken into account in the preparation of a pilot study. Consequently, experiences from the pilot study were used to design the study protocol. Approximately 2000 patients with an occupational injury will be recruited from the emergency departments in Herning and Odense, Denmark. A standardised questionnaire will be used to collect basic demographic data and information on eight transient risk factors. Based on previous studies and knowledge on occupational injuries the transient risk factors we chose to examine were: time pressure, performing a task with a different method/using unaccustomed technique, change in working surroundings, using a phone, disagreement, feeling ill, being distracted and using malfunctioning machinery/tools or work material. Exposure time 'just before the injury' will be compared with two control periods, 'previous day at the same time of the injury' (pair match) and the previous work week (usual frequency). This study protocol describes a unique opportunity to calculate the effect of transient risk factors on occupational injuries in a European setting. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Synchronized navigation of current and prior studies using image registration improves radiologist's efficiency.

PubMed

Forsberg, Daniel; Gupta, Amit; Mills, Christopher; MacAdam, Brett; Rosipko, Beverly; Bangert, Barbara A; Coffey, Michael D; Kosmas, Christos; Sunshine, Jeffrey L

2017-03-01

The purpose of this study was to investigate how the use of multi-modal rigid image registration integrated within a standard picture archiving and communication system affects the efficiency of a radiologist while performing routine interpretations of cases including prior examinations. Six radiologists were recruited to read a set of cases (either 16 neuroradiology or 14 musculoskeletal cases) during two crossover reading sessions. Each radiologist read each case twice, one time with synchronized navigation, which enables spatial synchronization across examinations from different study dates, and one time without. Efficiency was evaluated based upon time to read a case and amount of scrolling while browsing a case using Wilcoxon signed rank test. Significant improvements in efficiency were found considering either all radiologists simultaneously, the two sections separately and the majority of individual radiologists for time to read and for amount of scrolling. The relative improvement for each individual radiologist ranged from 4 to 32% for time to read and from 14 to 38% for amount of scrolling. Image registration providing synchronized navigation across examinations from different study dates provides a tool that enables radiologists to work more efficiently while reading cases with one or more prior examinations.

The European Working Time Directive and training in cardiothoracic surgery in the United Kingdom.

PubMed

West, D; Codispoti, M; Graham, T

2007-04-01

The European Working Time Directive (EWTD) limited average working hours for junior doctors to 58 per week in 2004. The Cardiothoracic Specialty Advisory Board conducted postal and email surveys of cardiothoracic trainees' work patterns and attitudes in 2003 and 2005-6. The results reveal an increase in shift-based working from 15% to 58% of respondents. One hundred per cent of respondents felt that the EWTD had had a negative impact on training, and only 30% were satisfied with their training to date. Satisfied trainees were more likely to work in larger units as assessed by ITU beds (20.6 vs. 8.9, p < 0.001) and cardiac cases/year (1586.2 vs. 828.4, p < 0.001). They had performed more cardiac cases than their peers (72.7 vs. 26.7, p = 0.005). Fifty-two per cent thought that their quality of life improved after EWTD implementation. The EWTD is unpopular amongst cardiothoracic trainees, who perceive it as harming training. Overall trainee satisfaction is low. Larger units and increased personal operative experience are associated with trainee satisfaction. Training programmes must act vigorously to safeguard training quality before implementation of the 48-hour limit in 2009.

Night shift work, chronotype and prostate cancer risk in the MCC-Spain case-control study.

PubMed

Papantoniou, Kyriaki; Castaño-Vinyals, Gemma; Espinosa, Ana; Aragonés, Nuria; Pérez-Gómez, Beatriz; Burgos, Javier; Gómez-Acebo, Inés; Llorca, Javier; Peiró, Rosana; Jimenez-Moleón, Jose Juan; Arredondo, Francisco; Tardón, Adonina; Pollan, Marina; Kogevinas, Manolis

2015-09-01

Night shift work has been classified as a probable human carcinogen based on experimental studies and limited human evidence on breast cancer. Evidence on other common cancers, such as prostate cancer, is scarce. Chronotype is an individual characteristic that may relate to night work adaptation. We evaluated night shift work with relation to prostate cancer, taking into account chronotype and disease severity in a population based case-control study in Spain. We included 1,095 prostate cancer cases and 1,388 randomly selected population controls. We collected detailed information on shift schedules (permanent vs. rotating, time schedules, duration, frequency), using lifetime occupational history. Sociodemographic and lifestyle factors were assessed by face-to-face interviews and chronotype through a validated questionnaire. We used unconditional logistic regression analysis adjusting for potential confounders. Subjects who had worked at least for one year in night shift work had a slightly higher prostate cancer risk [Odds Ratio (OR) 1.14; 95%CI 0.94, 1.37] compared with never night workers; this risk increased with longer duration of exposure (≥ 28 years: OR 1.37; 95%CI 1.05, 1.81; p-trend = 0.047). Risks were more pronounced for high risk tumors [D'Amico classification, Relative Risk Ratio (RRR) 1.40; 95%CI 1.05, 1.86], particularly among subjects with longer duration of exposure (≥28 years: RRR 1.63; 95%CI 1.08, 2.45; p-trend = 0.027). Overall risk was higher among subjects with an evening chronotype, but also increased in morning chronotypes after long-term night work. In this large population based study, we found an association between night shift work and prostate cancer particularly for tumors with worse prognosis. © 2014 UICC.

Beyond Newton's law of cooling - estimation of time since death

NASA Astrophysics Data System (ADS)

Leinbach, Carl

2011-09-01

The estimate of the time since death and, thus, the time of death is strictly that, an estimate. However, the time of death can be an important piece of information in some coroner's cases, especially those that involve criminal or insurance investigations. It has been known almost from the beginning of time that bodies cool after the internal mechanisms such as circulation of the blood stop. A first attempt to link this phenomenon to the determination of the time of death used a crude linear relationship. Towards the end of the nineteenth century, Newton's law of cooling using body temperature data obtained by the coroner was used to make a more accurate estimate. While based on scientific principles and resulting in a better estimate, Newton's law does not really describe the cooling of a non-homogeneous human body. This article will discuss a more accurate model of the cooling process based on the theoretical work of Marshall and Hoare and the laboratory-based statistical work of Claus Henssge. Using DERIVE®6.10 and the statistical work of Henssge, the double exponential cooling formula developed by Marshall and Hoare will be explored. The end result is a tool that can be used in the field by coroner's scene investigators to determine a 95% confidence interval for the time since death and, thus, the time of death.

Work-related olfactory disorder: a case series and review.

PubMed

Park, Soon Woo; Kang, Young Joong; Eom, Huisu; Cho, Hyun-Jin; Ahn, Jungho; Lee, Sang-Gil

2018-01-01

The olfactory bulb is anatomically exposed and thus can be directly damaged by external stimulation. This can occur as an occupational injury owing to contact with organic solvents or other causes. We present cases of eight patients who sustained occupation-related exposure to potentially toxic substances and later presented with signs and symptoms of anosmia. We examined the occupational and medical characteristics of the patients and evaluated their work-relatedness. Case 1: A 50-year-old man performed high-frequency heat treatments for approximately 11 years. He experienced decreased senses for olfaction and taste during the later years culminating in the diagnosis of anosmia after 3 years (high work-relatedness). Case 2: A 54-year-old man whose work involved exposure to various organic solvents, such as spray painting and application of paint and thinners for approximately 4 years, was subsequently diagnosed with anosmia based on rhinorrhea, headache, and loss of olfaction (high work-relatedness). Case 3: A 44-year-old-man who performed spray painting for approximately 17 years developed anosmia (high work-relatedness). Case 4: A 44-year-old man was involved in ship engine cleaning once a month, for approximately 7 h per cleaning session; he was diagnosed with anosmia based on loss of olfaction (low work-relatedness). Case 5: A 41-year-old man worked in ship building block construction for approximately 13 years; anosmia diagnosis was based on loss of olfaction (low work-relatedness). Case 6: A 47-year-old woman performed product inspection and labeling at a plant manufacturing automobile parts; anosmia diagnosis was based on decreased olfaction and taste (low work-relatedness). Case 7: A 50-year-old woman performed epoxy coating in a plant manufacturing automobile parts; anosmia diagnosis was based on diminishing olfaction (low work-relatedness). Case 8: A 57-year-old woman performed cleaning of the area where mobile phone parts were manufactured; anosmia diagnosis was based on diminishing olfaction (low work-relatedness). The study results confirmed work-relatedness when the subject was young, and the duration of exposure was long without any other cause of anosmia. Regarding compensation for occupational diseases, work-relatedness can be recognized as a relative concept.

Numerical and Experimental Case Study of Blasting Works Effect

NASA Astrophysics Data System (ADS)

Papán, Daniel; Valašková, Veronika; Drusa, Marian

2016-10-01

This article introduces the theoretical and experimental case study of dynamic monitoring of the geological environment above constructed highway tunnel. The monitored structure is in this case a very important water supply pipeline, which crosses the tunnel and was made from steel tubes with a diameter of 800 mm. The basic dynamic parameters had been monitored during blasting works, and were compared with the FEM (Finite Element Method) calculations and checked by the Slovak standard limits. A calibrated FEM model based on the experimental measurement data results was created and used in order to receive more realistic results in further predictions, time and space extrapolations. This case study was required and demanded by the general contractor company and also by the owner of water pipeline, and it was an answer of public safety evaluation of risks during tunnel construction.

Virtual Reality Based Support System for Layout Planning and Programming of an Industrial Robotic Work Cell

PubMed Central

Yap, Hwa Jen; Taha, Zahari; Md Dawal, Siti Zawiah; Chang, Siow-Wee

2014-01-01

Traditional robotic work cell design and programming are considered inefficient and outdated in current industrial and market demands. In this research, virtual reality (VR) technology is used to improve human-robot interface, whereby complicated commands or programming knowledge is not required. The proposed solution, known as VR-based Programming of a Robotic Work Cell (VR-Rocell), consists of two sub-programmes, which are VR-Robotic Work Cell Layout (VR-RoWL) and VR-based Robot Teaching System (VR-RoT). VR-RoWL is developed to assign the layout design for an industrial robotic work cell, whereby VR-RoT is developed to overcome safety issues and lack of trained personnel in robot programming. Simple and user-friendly interfaces are designed for inexperienced users to generate robot commands without damaging the robot or interrupting the production line. The user is able to attempt numerous times to attain an optimum solution. A case study is conducted in the Robotics Laboratory to assemble an electronics casing and it is found that the output models are compatible with commercial software without loss of information. Furthermore, the generated KUKA commands are workable when loaded into a commercial simulator. The operation of the actual robotic work cell shows that the errors may be due to the dynamics of the KUKA robot rather than the accuracy of the generated programme. Therefore, it is concluded that the virtual reality based solution approach can be implemented in an industrial robotic work cell. PMID:25360663

Virtual reality based support system for layout planning and programming of an industrial robotic work cell.

PubMed

Yap, Hwa Jen; Taha, Zahari; Dawal, Siti Zawiah Md; Chang, Siow-Wee

2014-01-01

Traditional robotic work cell design and programming are considered inefficient and outdated in current industrial and market demands. In this research, virtual reality (VR) technology is used to improve human-robot interface, whereby complicated commands or programming knowledge is not required. The proposed solution, known as VR-based Programming of a Robotic Work Cell (VR-Rocell), consists of two sub-programmes, which are VR-Robotic Work Cell Layout (VR-RoWL) and VR-based Robot Teaching System (VR-RoT). VR-RoWL is developed to assign the layout design for an industrial robotic work cell, whereby VR-RoT is developed to overcome safety issues and lack of trained personnel in robot programming. Simple and user-friendly interfaces are designed for inexperienced users to generate robot commands without damaging the robot or interrupting the production line. The user is able to attempt numerous times to attain an optimum solution. A case study is conducted in the Robotics Laboratory to assemble an electronics casing and it is found that the output models are compatible with commercial software without loss of information. Furthermore, the generated KUKA commands are workable when loaded into a commercial simulator. The operation of the actual robotic work cell shows that the errors may be due to the dynamics of the KUKA robot rather than the accuracy of the generated programme. Therefore, it is concluded that the virtual reality based solution approach can be implemented in an industrial robotic work cell.

Output synchronization of discrete-time dynamical networks based on geometrically incremental dissipativity.

PubMed

Li, Chensong; Zhao, Jun

2017-01-01

In this work, we investigate the output synchronization problem for discrete-time dynamical networks with identical nodes. Firstly, if each node of a network is geometrically incrementally dissipative, the entire network can be viewed as a geometrically dissipative nonlinear system by choosing a particular input-output pair. Then, based on the geometrical dissipativity property, we consider two cases: output synchronization under arbitrary topology and switching topology, respectively. For the first case, we establish several criteria of output synchronization under arbitrary switching between a set of connection topologies by employing a common Lyapunov function. For the other case, we give the design method of a switching signal to achieve output synchronization even if all subnetworks are not synchronous. Finally, an example is provided to illustrate the effectiveness of the main results. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Cooperative Learning through Team-Based Projects in the Biotechnology Industry †

PubMed Central

Luginbuhl, Sarah C.; Hamilton, Paul T.

2013-01-01

We have developed a cooperative-learning, case studies project model that has teams of students working with biotechnology professionals on company-specific problems. These semester-long, team-based projects can be used effectively to provide students with valuable skills in an industry environment and experience addressing real issues faced by biotechnology companies. Using peer-evaluations, we have seen improvement in students’ professional skills such as time-management, quality of work, and level of contribution over multiple semesters. This model of team-based, industry-sponsored projects could be implemented in other college and university courses/programs to promote professional skills and expose students to an industry setting. PMID:24358386

Cooperative Learning through Team-Based Projects in the Biotechnology Industry.

PubMed

Luginbuhl, Sarah C; Hamilton, Paul T

2013-01-01

We have developed a cooperative-learning, case studies project model that has teams of students working with biotechnology professionals on company-specific problems. These semester-long, team-based projects can be used effectively to provide students with valuable skills in an industry environment and experience addressing real issues faced by biotechnology companies. Using peer-evaluations, we have seen improvement in students' professional skills such as time-management, quality of work, and level of contribution over multiple semesters. This model of team-based, industry-sponsored projects could be implemented in other college and university courses/programs to promote professional skills and expose students to an industry setting.

Infusing an Inter-Professional and Inter-University Perspective into Healthcare Education

ERIC Educational Resources Information Center

Goldberg, Lynette R.; Koontz, Jennifer Scott; Downs, David; Uhlig, Paul; Kumar, Neil G.; Shah, Sapna; Clark, Paige E.; Coiner, Christina; Crumrine, Daiquirie

2010-01-01

A national (USA) student-led, case-based CLinician/Administrator Relationship Improvement OrganizatioN (CLARION) competition focuses students in medical and related healthcare programs on the provision of healthcare that is safe, timely, equitable, patient-centred, effective and efficient. Students work in four-person, inter-professional teams to…

Epidemiological, clinical and laboratory profile of scrub typhus cases detected by serology and RT-PCR in Kumaon, Uttarakhand: a hospital-based study.

PubMed

Rawat, Vinita; Singh, Rajesh Kumar; Kumar, Ashok; Saxena, Sandip R; Varshney, Umesh; Kumar, Mukesh

2018-04-01

We analysed the epidemiology, clinical and laboratory data of the 168 scrub typhus cases confirmed by a combination of any one of the following: real time polymerase chain reaction (RT-PCR) and/or immunofluorescence assay (IFA) (IgM and/or IgG). The peak season for scrub typhus was from July to October. By multivariate binary logistic regression analysis, the risk of scrub typhus was about four times in those working in occupation related to forest work. Major clinical manifestations were fever (100%), myalgia (65%), cough (51%) and vomiting (46%); major complications were meningitis/meningoencephatilitis (12.5%) and multi-organ failure (MOF) and pneumonia (5.3% each). Laboratory investigations revealed raised aminotranferase levels and thrombocytopenia in most confirmed cases. We conclude that scrub typhus is an important cause of febrile illness in the Kumaon hills of Uttarakhand where this disease had not previously been considered to exist.

Charge Transfer Inefficiency in Pinned Photodiode CMOS image sensors: Simple Montecarlo modeling and experimental measurement based on a pulsed storage-gate method

NASA Astrophysics Data System (ADS)

Pelamatti, Alice; Goiffon, Vincent; Chabane, Aziouz; Magnan, Pierre; Virmontois, Cédric; Saint-Pé, Olivier; de Boisanger, Michel Breart

2016-11-01

The charge transfer time represents the bottleneck in terms of temporal resolution in Pinned Photodiode (PPD) CMOS image sensors. This work focuses on the modeling and estimation of this key parameter. A simple numerical model of charge transfer in PPDs is presented. The model is based on a Montecarlo simulation and takes into account both charge diffusion in the PPD and the effect of potential obstacles along the charge transfer path. This work also presents a new experimental approach for the estimation of the charge transfer time, called pulsed Storage Gate (SG) method. This method, which allows reproduction of a ;worst-case; transfer condition, is based on dedicated SG pixel structures and is particularly suitable to compare transfer efficiency performances for different pixel geometries.

Does a Case-Based Online Group Project Increase Students' Satisfaction with Interaction in Online Courses?

ERIC Educational Resources Information Center

Lee, Sang Joon; Ngampornchai, Anchalee; Trail-Constant, Trudian; Abril, Andres; Srinivasan, Sandhya

2016-01-01

Due to the realistic, complex natures of authentic cases involved in case-based learning, the use of group work has been encouraged and expected to enhance the quality of interaction among participants and to improve students' learning experiences. The purpose of this study was to investigate whether the case-based online group work increased…

78 FR 36248 - Appendix B Guidelines for Reviewing Applications for Compensation and Reimbursement of Expenses...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-17

... recruiting and training. k. Non-working travel: Whether the application includes time billed for non-working... professional's full rate for time spent traveling without actively working on the bankruptcy case or while... $50 million or more in liabilities, aggregated for jointly administered cases. Single asset real...

Real-time volcano monitoring using GNSS single-frequency receivers

NASA Astrophysics Data System (ADS)

Lee, Seung-Woo; Yun, Sung-Hyo; Kim, Do Hyeong; Lee, Dukkee; Lee, Young J.; Schutz, Bob E.

2015-12-01

We present a real-time volcano monitoring strategy that uses the Global Navigation Satellite System (GNSS), and we examine the performance of the strategy by processing simulated and real data and comparing the results with published solutions. The cost of implementing the strategy is reduced greatly by using single-frequency GNSS receivers except for one dual-frequency receiver that serves as a base receiver. Positions of the single-frequency receivers are computed relative to the base receiver on an epoch-by-epoch basis using the high-rate double-difference (DD) GNSS technique, while the position of the base station is fixed to the values obtained with a deferred-time precise point positioning technique and updated on a regular basis. Since the performance of the single-frequency high-rate DD technique depends on the conditions of the ionosphere over the monitoring area, the ionospheric total electron content is monitored using the dual-frequency data from the base receiver. The surface deformation obtained with the high-rate DD technique is eventually processed by a real-time inversion filter based on the Mogi point source model. The performance of the real-time volcano monitoring strategy is assessed through a set of tests and case studies, in which the data recorded during the 2007 eruption of Kilauea and the 2005 eruption of Augustine are processed in a simulated real-time mode. The case studies show that the displacement time series obtained with the strategy seem to agree with those obtained with deferred-time, dual-frequency approaches at the level of 10-15 mm. Differences in the estimated volume change of the Mogi source between the real-time inversion filter and previously reported works were in the range of 11 to 13% of the maximum volume changes of the cases examined.

Worked Examples Leads to Better Performance in Analyzing and Solving Real-Life Decision Cases

ERIC Educational Resources Information Center

Cevik, Yasemin Demiraslan; Andre, Thomas

2012-01-01

This study compared the impact of three types of case-based methods (worked example, faded worked example, and case-based reasoning) on preservice teachers' (n=71) decision making and reasoning related to realistic classroom management situations. Participants in this study received a short-term implementation of one of these three major…

The content and meaning of administrative work: a qualitative study of nursing practices.

PubMed

Michel, Lucie; Waelli, Mathias; Allen, Davina; Minvielle, Etienne

2017-09-01

To investigate the content and meaning of nurses' administrative work. Nurses often report that administrative work keeps them away from bedside care. The content and meaning of this work remains insufficiently explored. Comparative case studies. The investigation took place in 2014. It was based on 254 hours of observations and 27 interviews with nurses and staff in two contrasting units: intensive care and long-term care. A time and motion study was also performed over a period of 96 hours. Documentation and Organizational Activities is composed of six categories; documenting the patient record, coordination, management of patient flow, transmission of information, reporting quality indicators, ordering supplies- stock management Equal amounts of time were spent on these activities in each case. Nurses did not express complaints about documentation in intensive care, whereas they reported feeling frustrated by it in long-term care. These differences reflected the extent to which these activities could be integrated into nurses' clinical work and this is in turn was related to several factors: staff ratios, informatics, and relevance to nursing work. Documentation and Organizational Activities are a main component of care. The meaning nurses attribute to them is dependent on organizational context. These activities are often perceived as competing with bedside care, but this does not have to be the case. The challenge for managers is to fully integrate them into nursing practice. Results also suggest that nurses' Documentation and Organizational Activities should be incorporated into informatics strategies. © 2017 John Wiley & Sons Ltd.

Bayesian analysis of time-series data under case-crossover designs: posterior equivalence and inference.

PubMed

Li, Shi; Mukherjee, Bhramar; Batterman, Stuart; Ghosh, Malay

2013-12-01

Case-crossover designs are widely used to study short-term exposure effects on the risk of acute adverse health events. While the frequentist literature on this topic is vast, there is no Bayesian work in this general area. The contribution of this paper is twofold. First, the paper establishes Bayesian equivalence results that require characterization of the set of priors under which the posterior distributions of the risk ratio parameters based on a case-crossover and time-series analysis are identical. Second, the paper studies inferential issues under case-crossover designs in a Bayesian framework. Traditionally, a conditional logistic regression is used for inference on risk-ratio parameters in case-crossover studies. We consider instead a more general full likelihood-based approach which makes less restrictive assumptions on the risk functions. Formulation of a full likelihood leads to growth in the number of parameters proportional to the sample size. We propose a semi-parametric Bayesian approach using a Dirichlet process prior to handle the random nuisance parameters that appear in a full likelihood formulation. We carry out a simulation study to compare the Bayesian methods based on full and conditional likelihood with the standard frequentist approaches for case-crossover and time-series analysis. The proposed methods are illustrated through the Detroit Asthma Morbidity, Air Quality and Traffic study, which examines the association between acute asthma risk and ambient air pollutant concentrations. © 2013, The International Biometric Society.

Examining Preservice Teachers' Decision Behaviors and Individual Differences in Three Online Case-Based Approaches

ERIC Educational Resources Information Center

Cevik, Yasemin Demiraslan; Andre, Thomas

2013-01-01

This study compared the impact of three types of case-based methods (case-based reasoning, worked example, and faded worked example) on preservice teachers' (n = 71) interaction with decision tasks and whether decision related measures (task difficulty, mental effort, decision making performance) were associated with the differences in student…

a Study on Satellite Diagnostic Expert Systems Using Case-Based Approach

NASA Astrophysics Data System (ADS)

Park, Young-Tack; Kim, Jae-Hoon; Park, Hyun-Soo

1997-06-01

Many research works are on going to monitor and diagnose diverse malfunctions of satellite systems as the complexity and number of satellites increase. Currently, many works on monitoring and diagnosis are carried out by human experts but there are needs to automate much of the routine works of them. Hence, it is necessary to study on using expert systems which can assist human experts routine work by doing automatically, thereby allow human experts devote their expertise more critical and important areas of monitoring and diagnosis. In this paper, we are employing artificial intelligence techniques to model human experts' knowledge and inference the constructed knowledge. Especially, case-based approaches are used to construct a knowledge base to model human expert capabilities which use previous typical exemplars. We have designed and implemented a prototype case-based system for diagnosing satellite malfunctions using cases. Our system remembers typical failure cases and diagnoses a current malfunction by indexing the case base. Diverse methods are used to build a more user friendly interface which allows human experts can build a knowledge base in as easy way.

How Work Organization Affects the Prevalence of WMSDs: A Case-control Study.

PubMed

Liu, Lu; Chen, Song Gen; Tang, Shi Chuan; Wang, Sheng; He, Li Hua; Guo, Ze Hua; Li, Jing Yun; Yu, Shan Fa; Wang, Zhong Xu

2015-09-01

In this study, we aimed at exploring the association between work-related musculoskeletal disorders (WMSDs) and work organization based on a case-control study. A total of 1938 workers who claimed to suffer from WMSDs were selected from Beijing, Henan, Hubei, and the Guangdong province. The control group consisted of 2009 workers employed in similar industries without severe disease or musculoskeletal discomforts. We used a modified version of the questionnaire developed by the NMQ and the DMQ to investigate individual and work-related factors. A total of 13 variables (P<0.1) were selected by the chi-square test and finally, 7 variables entered into the equation, with 6 variables reaching statistical significance (P<0.05). The odds ratios (OR) of 'work changing with season' and 'sufficient rest time' did not reach 1 (0.749 and 0.441, respectively). In addition, 'sufficient rest time' seemed to be the stronger protective factor according to its higher standardized coefficient. And 'repetitive work every minute', 'constantly repetitive work' (every day), 'shortage of site personnel', and 'often switching shifts with others' seemed to be the risk factors. Work organization may have comprehensive effects on the occurrence of WMSDs. This pattern of associations suggests that further investigation into the mechanism of how work organization affects the prevalence of WMSDs is required. Copyright © 2015 The Editorial Board of Biomedical and Environmental Sciences. Published by China CDC. All rights reserved.

Dealing with anxiety disorders in the workplace: importance of early intervention when anxiety leads to absence from work.

PubMed

Nash-Wright, Jennifer

2011-01-01

A report from the Partnership on Workplace Mental Health, a program of the American Psychiatric Foundation, supports the widely held view that intervening early in a psychiatric disability absence will result in earlier return to work and reduce the likelihood of permanent disability. Studies unfortunately reveal that patients with psychiatric illness do not receive a level of care consistent with evidence-based best practice. This article highlights the importance of early interventions that utilize best practices for anxiety disorders that impair an employee's occupational functioning. Behavioral Health Consulting Firm. Studies on occupational disability conclude that collaborative communication between clinicians, disability case managers, and the employer is important to facilitate a successful and timely return to work for employees with temporary psychiatric disability. Avoidance of preexisting workplace conflicts can undermine return to work. Undertreatment and ineffective treatment are common causes of delayed recovery from acute anxiety conditions. In addition, lack of urgency among clinicians regarding the crisis nature of absence from work due to psychiatric illness can contribute to lengthy and unnecessary absence from work. A basic understanding of the acute aspects of anxiety disorders can assist disability case managers working in collaboration with treating clinicians and employees in a successful and timely return to work when an anxiety condition leads to absence from work.

Students Using a Novel Web-Based Laboratory Class Support System: A Case Study in Food Chemistry Education

ERIC Educational Resources Information Center

van der Kolk, Koos; Beldman, Gerrit; Hartog, Rob; Gruppen, Harry

2012-01-01

The design, usage, and evaluation of a Web-based laboratory manual (WebLM) are described. The main aim of the WebLM is to support students while working in the laboratory by providing them with just-in-time information. Design guidelines for this electronic manual were derived from literature on cognitive load and user interface design. The WebLM…

Time trends in incidence of myocardial infarction in male and female dominated occupations in Stockholm, Sweden.

PubMed

Ostlin, Piroska; Klerdal, Kristina; Hammar, Niklas

2008-07-01

To investigate time trends in first acute myocardial infarction (MI) incidence in male and female dominated occupations in Stockholm during 1977-1996. Population-based case-control study, where all first events of acute MI among participants aged 40-69 in Stockholm 1977-1996 were identified, using registers of hospital discharges and deaths. Controls were selected randomly using national population registers. There were 16,531 male and 4382 female cases and 117,015 male and 102,083 female controls. In all, 222 female cases worked in male dominated occupations and 844 male cases worked in female dominated occupations. Both women and men in male dominated occupations showed an elevated relative risk of first MI compared to other employees during the study period. Between 1985-1996, when there was a general decline in MI incidence in Sweden, women in male dominated occupations tended to show an increasing trend. Women in female dominated high and intermediate occupations had a lower relative risk of MI compared to other women in the same socioeconomic group. In male dominated and non-manual female dominated occupations a decline in the incidence of MI was seen during 1985-1996 in men but not in women. Work in male dominated occupations appears to be associated with an increased risk of MI in both genders. There is a need to investigate possible work related or other factors that may be driving this elevated risk.

Learning in the workplace: Fostering resilience in disengaged youth.

PubMed

Deluca, Christopher; Hutchinson, Nancy L; Delugt, Jennifer S; Beyer, Wanda; Thornton, Antoinette; Versnel, Joan; Chin, Peter; Munby, Hugh

2010-01-01

International reports on school-to-work transition make it clear that worldwide youth are at-risk for educational disengagement and are three times as likely to be unemployed as their adult counterparts. Work-based education (WBE) is one of the most frequently recommended solutions for youth disengagement which suggests that WBE serves as a protective factor and encourages resilience in at-risk youth. The objective of this study was to describe and compare the experiences of two at-risk youth enrolled in WBE. Two 18-year old at-risk youth enrolled in WBE were chosen for study because they were learning in workplaces judged likely to promote resilience. Both had been disengaged from school prior to enrolling in WBE. Each multiple-perspective case study includes the perspective of the youth, the workplace employer, and the work-based educator. Data consisted of ethnographic observations and interviews conducted at the workplace, and with the teacher in the school. Each case study highlights how supportive adults and an at-risk youth engage in interactions that facilitate the emergence of resilience in the workplace. In these two cases, risk and resilience are context specific, suggesting that at-risk youth may require tailored workplace programs to meet their career development needs.

Improving a Field School Curriculum Using Modularized Lessons and Authentic Case-Based Learning

ERIC Educational Resources Information Center

Rea, Roy V.; Hodder, Dexter P.

2007-01-01

University course evaluations are replete with student comments expressing frustration with taking time out of work, paying money for, and putting energy into field education projects that lack authentic "real-world" problem-solving objectives. Here, we describe a model for field school education that borrows on pedagogical tools such as…

Work-Based Learning for Adolescents with Learning Disabilities: Creating a Context for Success

ERIC Educational Resources Information Center

Versnel, Joan; Hutchinson, Nancy L.; Munby, Hugh; Chin, Peter

2008-01-01

This paper describes cases of two adolescents with learning disabilities working in automotive repair businesses as part of a work-based education program. Neither adolescent was judged to have been successful by the workplace supervisors. The frameworks chosen for analyzing these cases draw upon recent work in self-determination, workplace…

Implementation of standardized time limits in sickness insurance and return-to-work: experiences of four actors.

PubMed

Ståhl, Christian; Müssener, Ulrika; Svensson, Tommy

2012-01-01

In 2008, time limits were introduced in Swedish sickness insurance, comprising a pre-defined schedule for return-to-work. The purpose of this study was to explore experienced consequences of these time limits. Sick-listed persons, physicians, insurance officials and employers were interviewed regarding the process of sick-listing, rehabilitation and return-to-work in relation to the reform. The study comprises qualitative interviews with 11 sick-listed persons, 4 insurance officials, 5 employers and 4 physicians (n = 24). Physicians, employers, and sick-listed persons described insurance officials as increasingly passive, and that responsibility for the process was placed on the sick-listed. Several ethical dilemmas were identified, where officials were forced to act against their ethical principles. Insurance officials' principle of care often clashed with the standardization of the process, that is based on principles of egalitarianism and equal treatment. The cases reported in this study suggest that a policy for activation and early return-to-work in some cases has had the opposite effect: central actors remain passive and the responsibility is placed on the sick-listed, who lacks the strength and knowledge to understand and navigate through the system. The standardized insurance system here promoted experiences of procedural injustice, for both officials and sick-listed persons.

Measurement methods and accuracy in copy number variation: failure to replicate associations of beta-defensin copy number with Crohn's disease.

PubMed

Aldhous, Marian C; Abu Bakar, Suhaili; Prescott, Natalie J; Palla, Raquel; Soo, Kimberley; Mansfield, John C; Mathew, Christopher G; Satsangi, Jack; Armour, John A L

2010-12-15

The copy number variation in beta-defensin genes on human chromosome 8 has been proposed to underlie susceptibility to inflammatory disorders, but presents considerable challenges for accurate typing on the scale required for adequately powered case-control studies. In this work, we have used accurate methods of copy number typing based on the paralogue ratio test (PRT) to assess beta-defensin copy number in more than 1500 UK DNA samples including more than 1000 cases of Crohn's disease. A subset of 625 samples was typed using both PRT-based methods and standard real-time PCR methods, from which direct comparisons highlight potentially serious shortcomings of a real-time PCR assay for typing this variant. Comparing our PRT-based results with two previous studies based only on real-time PCR, we find no evidence to support the reported association of Crohn's disease with either low or high beta-defensin copy number; furthermore, it is noteworthy that there are disagreements between different studies on the observed frequency distribution of copy number states among European controls. We suggest safeguards to be adopted in assessing and reporting the accuracy of copy number measurement, with particular emphasis on integer clustering of results, to avoid reporting of spurious associations in future case-control studies.

Examining Preservice Teachers' Classroom Management Decisions in Three Case-Based Teaching Approaches

ERIC Educational Resources Information Center

Cevik, Yasemin Demiraslan; Andre, Thomas

2013-01-01

This study was aimed at comparing the impact of three types of case-based approaches (worked example, faded work example, and case-based reasoning) on preservice teachers' decision making and reasoning skills related to realistic classroom management situations. Participants in this study received a short-term implementation of one of these three…

Interactive Land-Use Optimization Using Laguerre Voronoi Diagram with Dynamic Generating Point Allocation

NASA Astrophysics Data System (ADS)

Chaidee, S.; Pakawanwong, P.; Suppakitpaisarn, V.; Teerasawat, P.

2017-09-01

In this work, we devise an efficient method for the land-use optimization problem based on Laguerre Voronoi diagram. Previous Voronoi diagram-based methods are more efficient and more suitable for interactive design than discrete optimization-based method, but, in many cases, their outputs do not satisfy area constraints. To cope with the problem, we propose a force-directed graph drawing algorithm, which automatically allocates generating points of Voronoi diagram to appropriate positions. Then, we construct a Laguerre Voronoi diagram based on these generating points, use linear programs to adjust each cell, and reconstruct the diagram based on the adjustment. We adopt the proposed method to the practical case study of Chiang Mai University's allocated land for a mixed-use complex. For this case study, compared to other Voronoi diagram-based method, we decrease the land allocation error by 62.557 %. Although our computation time is larger than the previous Voronoi-diagram-based method, it is still suitable for interactive design.

Time management in health care social work.

PubMed

Sheridan, M S

1988-01-01

Health care social workers face significant problems in controlling and managing time. Among the causes are increased demands for service, economy measures in health care, and the concurrent responsibility which social workers often have for both ongoing case management and crisis coverage. Individuals and social work departments can increase productivity through streamlining case management, increasing use of available resources, and generating new resources. With planning and preparation, many emergencies can be moved into the expected work flow. The social work profession needs to address time management problems and expectations in a more realistic and systematic way.

Dynamics of salivary proteins and metabolites during extreme endurance sports - a case study.

PubMed

Zauber, Henrik; Mosler, Stephan; von Heßberg, Andreas; Schulze, Waltraud X

2012-07-01

As noninvasively accessible body fluid, saliva is of growing interest in diagnostics. To exemplify the diagnostic potential of saliva, we used a mass spectrometry-based approach to gain insights into adaptive physiological processes underlying long-lasting endurance work load in a case study. Saliva was collected from male and female athlete at four diurnal time points throughout a 1060 km nonstop cycling event. Total sampling time covered 180 h comprising 62 h of endurance cycling as well as reference samples taken over 3 days before the event, and over 2 days after. Altogether, 1405 proteins and 62 metabolites were identified in these saliva samples, of which 203 could be quantified across the majority of the sampling time points. Many proteins show clear diurnal abundance patterns in saliva. In many cases, these patterns were disturbed and altered by the long-term endurance stress. During the stress phase, metabolites of energy mobilization, such as creatinine and glucose were of high abundance, as well as metabolites with antioxidant functions. Lysozyme, amylase, and proteins with redox-regulatory function showed significant increase in average abundance during work phase compared to rest or recovery phase. The recovery phase was characterized by an increased abundance of immunoglobulins. Our work exemplifies the application of high-throughput technologies to understand adaptive processes in human physiology. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Healing the healer: one step at a time.

PubMed

Gershon, J Casey

2014-03-01

Health care workers have the most challenging of professions. They are expected to work long hours while demonstrating compassion and care for the patients that they serve. Although health care practitioners are among the most disciplined of working professionals, they are often some of the unhealthiest of individuals, facing enormous amounts of stress in their lives. Healing the Healer: One Step at a Time is a 6-week health fitness program. It explores the unique challenges faced in the field of health care and teaches techniques to address those challenges head on. Healing the Healer uses Nordic walking as the exercise portion of the class. The case study examines the structure, purpose, and design of this 6-week course. Special attention is given to four basic sections: balance, pacing, joy, and discipline. The arguments presented in this article are theory based and supported by case study evidence.

45 CFR 260.75 - If a State is claiming a waiver inconsistency for work requirements or time limits, what must the...

Code of Federal Regulations, 2013 CFR

2013-10-01

... experimental and control groups, which are not otherwise exempt, for the purpose of calculating the work... all experimental group cases and/or control group cases, not otherwise exempt, but may not exclude...) The certification must specify any special work or time-limit standards that apply to the control...

45 CFR 260.75 - If a State is claiming a waiver inconsistency for work requirements or time limits, what must the...

Code of Federal Regulations, 2011 CFR

2011-10-01

... experimental and control groups, which are not otherwise exempt, for the purpose of calculating the work... all experimental group cases and/or control group cases, not otherwise exempt, but may not exclude...) The certification must specify any special work or time-limit standards that apply to the control...

45 CFR 260.75 - If a State is claiming a waiver inconsistency for work requirements or time limits, what must the...

Code of Federal Regulations, 2014 CFR

2014-10-01

... experimental and control groups, which are not otherwise exempt, for the purpose of calculating the work... all experimental group cases and/or control group cases, not otherwise exempt, but may not exclude...) The certification must specify any special work or time-limit standards that apply to the control...

45 CFR 260.75 - If a State is claiming a waiver inconsistency for work requirements or time limits, what must the...

Code of Federal Regulations, 2010 CFR

2010-10-01

... experimental and control groups, which are not otherwise exempt, for the purpose of calculating the work... all experimental group cases and/or control group cases, not otherwise exempt, but may not exclude...) The certification must specify any special work or time-limit standards that apply to the control...

45 CFR 260.75 - If a State is claiming a waiver inconsistency for work requirements or time limits, what must the...

Code of Federal Regulations, 2012 CFR

2012-10-01

... experimental and control groups, which are not otherwise exempt, for the purpose of calculating the work... all experimental group cases and/or control group cases, not otherwise exempt, but may not exclude...) The certification must specify any special work or time-limit standards that apply to the control...

Cost of unreliability method to estimate loss of revenue based on unreliability data: Case study of Printing Company

NASA Astrophysics Data System (ADS)

alhilman, Judi

2017-12-01

In the production line process of the printing office, the reliability of the printing machine plays a very important role, if the machine fail it can disrupt production target so that the company will suffer huge financial loss. One method to calculate the financial loss cause by machine failure is use the Cost of Unreliability(COUR) method. COUR method works based on down time machine and costs associated with unreliability data. Based on the calculation of COUR method, so the sum of cost due to unreliability printing machine during active repair time and downtime is 1003,747.00.

Decision PBL: A 4-year retrospective case study of the use of virtual patients in problem-based learning.

PubMed

Ellaway, Rachel H; Poulton, Terry; Jivram, Trupti

2015-01-01

In 2009, St George's University of London (SGUL) replaced their paper-based problem-based learning (PBL) cases with virtual patients for intermediate-level undergraduate students. This involved the development of Decision-Problem-Based Learning (D-PBL), a variation on progressive-release PBL that uses virtual patients instead of paper cases, and focuses on patient management decisions and their consequences. Using a case study method, this paper describes four years of developing and running D-PBL at SGUL from individual activities up to the ways in which D-PBL functioned as an educational system. A number of broad issues were identified: the importance of debates and decision-making in making D-PBL activities engaging and rewarding; the complexities of managing small group dynamics; the time taken to complete D-PBL activities; the changing role of the facilitator; and the erosion of the D-PBL process over time. A key point in understanding this work is the construction and execution of the D-PBL activity, as much of the value of this approach arises from the actions and interactions of students, their facilitators and the virtual patients rather than from the design of the virtual patients alone. At a systems level D-PBL needs to be periodically refreshed to retain its effectiveness.

Tsunami detection by high-frequency radar in British Columbia: performance assessment of the time-correlation algorithm for synthetic and real events

NASA Astrophysics Data System (ADS)

Guérin, Charles-Antoine; Grilli, Stéphan T.; Moran, Patrick; Grilli, Annette R.; Insua, Tania L.

2018-05-01

The authors recently proposed a new method for detecting tsunamis using high-frequency (HF) radar observations, referred to as "time-correlation algorithm" (TCA; Grilli et al. Pure Appl Geophys 173(12):3895-3934, 2016a, 174(1): 3003-3028, 2017). Unlike standard algorithms that detect surface current patterns, the TCA is based on analyzing space-time correlations of radar signal time series in pairs of radar cells, which does not require inverting radial surface currents. This was done by calculating a contrast function, which quantifies the change in pattern of the mean correlation between pairs of neighboring cells upon tsunami arrival, with respect to a reference correlation computed in the recent past. In earlier work, the TCA was successfully validated based on realistic numerical simulations of both the radar signal and tsunami wave trains. Here, this algorithm is adapted to apply to actual data from a HF radar installed in Tofino, BC, for three test cases: (1) a simulated far-field tsunami generated in the Semidi Subduction Zone in the Aleutian Arc; (2) a simulated near-field tsunami from a submarine mass failure on the continental slope off of Tofino; and (3) an event believed to be a meteotsunami, which occurred on October 14th, 2016, off of the Pacific West Coast and was measured by the radar. In the first two cases, the synthetic tsunami signal is superimposed onto the radar signal by way of a current memory term; in the third case, the tsunami signature is present within the radar data. In light of these test cases, we develop a detection methodology based on the TCA, using a correlation contrast function, and show that in all three cases the algorithm is able to trigger a timely early warning.

Distributed finite-time containment control for double-integrator multiagent systems.

PubMed

Wang, Xiangyu; Li, Shihua; Shi, Peng

2014-09-01

In this paper, the distributed finite-time containment control problem for double-integrator multiagent systems with multiple leaders and external disturbances is discussed. In the presence of multiple dynamic leaders, by utilizing the homogeneous control technique, a distributed finite-time observer is developed for the followers to estimate the weighted average of the leaders' velocities at first. Then, based on the estimates and the generalized adding a power integrator approach, distributed finite-time containment control algorithms are designed to guarantee that the states of the followers converge to the dynamic convex hull spanned by those of the leaders in finite time. Moreover, as a special case of multiple dynamic leaders with zero velocities, the proposed containment control algorithms also work for the case of multiple stationary leaders without using the distributed observer. Simulations demonstrate the effectiveness of the proposed control algorithms.

A Distance Blended Learning Program to Upgrade the Clinical Competence of District Non-doctor Anesthesia Providers in Nepal.

PubMed

Shah, Shristi; Knoble, Stephen; Ross, Oliver; Pickering, Stephen

2017-12-01

Across Nepal, anesthesia at a district level is provided mostly by non-doctor anesthesia providers (anesthesia assistants-AAs). Nepal's Government recognized the need to sustain competence with continuous professional development and to upgrade 6-month trained working AAs to professional equivalence with the new national standard of 12-month training. As they are essential district health workers and AA clinical training sites are full, an innovative distance blended learning, competency-based, upgrade 1-year course was developed and conducted in 2014-2017 for two batches. The course content was developed over 18 months by a team of Nepali and overseas AA training experts. The 1-year course started with a refresher course, continued with tablet-based 12-month self-learning modules and clinical case logs, regular educational mentor communication, midcourse 2-week contact time in an AA training site, regular text messaging and ended with clinical examination and multiple-choice questions. Tablet content included 168 new case studies, pre- and posttests, video lectures, matching exercises and a resource library. All module work and logged clinical cases were uploaded centrally, where clinical mentors were able to review work. Clinical skills were upgraded, as needed, through direct clinical contact midway through the course. Quantitative and qualitative course assessments were included. Fourteen working AAs in first batch and eight working AAs in second batch from district, zonal and mission hospitals across Nepal were enrolled. All remained working at their hospitals throughout the course, and there were no significant tablet problems inhibiting course completion. Twenty-one AAs completed all modules successfully with time required for module completion averaging 19.2 h (range 11.2-32). One AA left the course after 3 months with a personal problem. Subjectively, AAs felt that the obstetric and pediatric modules were more difficult; lowest marks were objectively seen in the airway module. Clinical mentors averaged 8.2 h mentoring review work per module with direct student communication of 2.9 h per module per month. Participants logged a total of 5473 clinical cases, ranging between 50 and 788 cases each. Complications were recorded; outcomes were good. Challenges were the national IT infrastructure making data synchronization difficult and the lack of clinical exposure at some AA's hospitals. Nineteen AAs attended the final examination, and all passed. Two AAs withdrew before the final examination period due to personal and logistic reasons. This is the first use of distance blended learning to upgrade district health workers in Nepal and perhaps for non-doctor anesthesia providers globally. Key success factors were motivated students, cultural and contextualized clinical content, good educational mentoring relationships with regular communication, central IT and motivational support, and face-to-face midcourse clinical contact time.

Guillain–Barré Syndrome in India: Population-based validation of the Brighton criteria

PubMed Central

Mateen, Farrah J.; Cornblath, David R.; Jafari, Hamid; Shinohara, Russell T.; Khandit, Devendra; Ahuja, Bina; Bahl, Sunil; Sutter, Roland W.

2013-01-01

Objective Case definitions of GBS were recently developed in response to the 2009 H1N1 vaccination programme but have undergone limited field testing. We validate the sensitivity of the Brighton Working Group case definitions for Guillain–Barré Syndrome (GBS) using a population-based cohort in India. Methods The National Polio Surveillance Unit of India actively collects all cases of acute flaccid paralysis (AFP) in children <15 years old, including cases of GBS. Cases of GBS with available cerebrospinal fluid(CSF) and nerve conduction studies (NCS) results, neurological examination, clinical history, and exclusion of related diagnoses were selected (2002–2003). Relevant data were abstracted and entered into a central database. Sensitivity of the Brighton GBS criteria for level 3 of diagnostic certainty which requires no clinical laboratory testing, level 2 which employs CSF or NCS, and level 1 which employs both, were calculated. Results 79 cases of GBS (mean age 6.5 years, range 4.0–14.5; 39% female) met the case definition. GBS cases were ascending (79%), symmetrical (85%), and bilateral (100%); involving lower extremity hypotonia (86%) and weakness (100%), upper extremity hypotonia (62%) and weakness (80%), areflexia/hyporeflexia (88%), respiratory muscles (22%), bulbar muscles (22%), and cranial nerves (13%). Four limbs were involved in 80% of cases. Mean time to maximal weakness was 5.2 days (range 0.5–30 days) with nadir GBS disability scores of 3 (7%), 4 (67%), 5 (15%), 6 (10%), or unclear (1%). CSF (mean time to lumbar puncture 29 days) was normal in 29% with cytoalbuminologic dissociation in 65% (mean protein 105 mg/dL, range 10–1000; mean cell count 11/μL, range 0–220, n = 4 with >50 cells/μL). Significant improvement occurred in 73% whereas death (9%) occurred 6–29 days after sensorimotor symptom onset. The majority of cases (86%) fulfilled Brighton level 3, level 2 (84%), and level 1 (62%) of diagnostic certainty. Conclusion The diagnosis of GBS can be made using Brighton Working Group criteria in India with moderate to high sensitivity. Brighton Working Group case definitions are a plausible standard for capturing a majority of cases of GBS in field operations in low income settings during AFP surveillance. PMID:22001121

Evaluation of the North Country on the Job Network: a model of facilitated care for injured workers in rural upstate New York.

PubMed

Lipscomb, Hester J; Moon, Samuel D; Li, Leiming; Pompeii, Lisa; Kennedy, Margaret Q

2002-03-01

We describe the evaluation of a community-based program designed to facilitate access to care and return to work for injured workers in a rural, medically underserved area in upstate New York. Providers are recruited to provide easily accessible care and are oriented to concepts of transitional duty and rapid return to work as medically appropriate; companies are recruited with the agreement to provide transitional work for injured employees. Registered nurses, hired by the local hospital, serve as case coordinators to facilitate care and coordinate communications among all parties. Over 3000 injured workers received care through the program in the first 56 months, with a decline in the number of transitional days over time. The number of days that the cases remain open has steadily declined, and the number of return-to-work cases has increased. The success of this initiative provides an excellent background for continued improvement in delivery of care to injured workers and proactive efforts at improving workplace safety and health in a rural area.

Expression for time travel based on diffusive wave theory: applicability and considerations

NASA Astrophysics Data System (ADS)

Aguilera, J. C.; Escauriaza, C. R.; Passalacqua, P.; Gironas, J. A.

2017-12-01

Prediction of hydrological response is of utmost importance when dealing with urban planning, risk assessment, or water resources management issues. With the advent of climate change, special care must be taken with respect to variations in rainfall and runoff due to rising temperature averages. Nowadays, while typical workstations have adequate power to run distributed routing hydrological models, it is still not enough for modeling on-the-fly, a crucial ability in a natural disaster context, where rapid decisions must be made. Semi-distributed time travel models, which compute a watershed's hydrograph without explicitly solving the full shallow water equations, appear as an attractive approach to rainfall-runoff modeling since, like fully distributed models, also superimpose a grid on the watershed, and compute runoff based on cell parameter values. These models are heavily dependent on the travel time expression for an individual cell. Many models make use of expressions based on kinematic wave theory, which is not applicable in cases where watershed storage is important, such as mild slopes. This work presents a new expression for concentration times in overland flow, based on diffusive wave theory, which considers not only the effects of storage but also the effects on upstream contribution. Setting upstream contribution equal to zero gives an expression consistent with previous work on diffusive wave theory; on the other hand, neglecting storage effects (i.e.: diffusion,) is shown to be equivalent to kinematic wave theory, currently used in many spatially distributed time travel models. The newly found expression is shown to be dependent on plane discretization, particularly when dealing with very non-kinematic cases. This is shown to be the result of upstream contribution, which gets larger downstream, versus plane length. This result also provides some light on the limits on applicability of the expression: when a certain kinematic threshold is reached, the expression is no longer valid, and one must fall back to kinematic wave theory, for lack of a better option. This expression could be used for improving currently published spatially distributed time travel models, since they would become applicable in many new cases.

Zero-moment point determination of worst-case manoeuvres leading to vehicle wheel lift

NASA Astrophysics Data System (ADS)

Lapapong, S.; Brown, A. A.; Swanson, K. S.; Brennan, S. N.

2012-01-01

This paper proposes a method to evaluate vehicle rollover propensity based on a frequency-domain representation of the zero-moment point (ZMP). Unlike other rollover metrics such as the static stability factor, which is based on the steady-state behaviour, and the load transfer ratio, which requires the calculation of tyre forces, the ZMP is based on a simplified kinematic model of the vehicle and the analysis of the contact point of the vehicle relative to the edge of the support polygon. Previous work has validated the use of the ZMP experimentally in its ability to predict wheel lift in the time domain. This work explores the use of the ZMP in the frequency domain to allow a chassis designer to understand how operating conditions and vehicle parameters affect rollover propensity. The ZMP analysis is then extended to calculate worst-case sinusoidal manoeuvres that lead to untripped wheel lift, and the analysis is tested across several vehicle configurations and compared with that of the standard Toyota J manoeuvre.

Molecular properties via a subsystem density functional theory formulation: a common framework for electronic embedding.

PubMed

Höfener, Sebastian; Gomes, André Severo Pereira; Visscher, Lucas

2012-01-28

In this article, we present a consistent derivation of a density functional theory (DFT) based embedding method which encompasses wave-function theory-in-DFT (WFT-in-DFT) and the DFT-based subsystem formulation of response theory (DFT-in-DFT) by Neugebauer [J. Neugebauer, J. Chem. Phys. 131, 084104 (2009)] as special cases. This formulation, which is based on the time-averaged quasi-energy formalism, makes use of the variation Lagrangian techniques to allow the use of non-variational (in particular: coupled cluster) wave-function-based methods. We show how, in the time-independent limit, we naturally obtain expressions for the ground-state DFT-in-DFT and WFT-in-DFT embedding via a local potential. We furthermore provide working equations for the special case in which coupled cluster theory is used to obtain the density and excitation energies of the active subsystem. A sample application is given to demonstrate the method. © 2012 American Institute of Physics

The psychosocial work environment is associated with risk of stroke at working age.

PubMed

Jood, Katarina; Karlsson, Nadine; Medin, Jennie; Pessah-Rasmussen, Hélène; Wester, Per; Ekberg, Kerstin

2017-07-01

Objective The aim of this study was to explore the relation between the risk of first-ever stroke at working age and psychological work environmental factors. Methods A consecutive multicenter matched 1:2 case-control study of acute stroke cases (N=198, age 30-65 years) who had been working full-time at the time of their stroke and 396 sex- and age-matched controls. Stroke cases and controls answered questionnaires on their psychosocial situation during the previous 12 months. The psychosocial work environment was assessed using three different measures: the job-control-demand model, the effort-reward imbalance (ERI) score, and exposures to conflict at work. Results Among 198 stroke cases and 396 controls, job strain [odds ratio (OR) 1.30, 95% confidence interval (95% CI) 1.05-1.62], ERI (OR 1.28, 95% CI 1.01-1.62), and conflict at work (OR 1.75, 95% CI 1.07-2.88) were independent risk factors of stroke in multivariable regression models. Conclusions Adverse psychosocial working conditions during the past 12 months were more frequently observed among stroke cases. Since these factors are presumably modifiable, interventional studies targeting job strain and emotional work environment are warranted.

The Effectiveness of a Web-Based Computer-Tailored Intervention on Workplace Sitting: A Randomized Controlled Trial.

PubMed

De Cocker, Katrien; De Bourdeaudhuij, Ilse; Cardon, Greet; Vandelanotte, Corneel

2016-05-31

Effective interventions to influence workplace sitting are needed, as office-based workers demonstrate high levels of continued sitting, and sitting too much is associated with adverse health effects. Therefore, we developed a theory-driven, Web-based, interactive, computer-tailored intervention aimed at reducing and interrupting sitting at work. The objective of our study was to investigate the effects of this intervention on objectively measured sitting time, standing time, and breaks from sitting, as well as self-reported context-specific sitting among Flemish employees in a field-based approach. Employees (n=213) participated in a 3-group randomized controlled trial that assessed outcomes at baseline, 1-month follow-up, and 3-month follow-up through self-reports. A subsample (n=122) were willing to wear an activity monitor (activPAL) from Monday to Friday. The tailored group received an automated Web-based, computer-tailored intervention including personalized feedback and tips on how to reduce or interrupt workplace sitting. The generic group received an automated Web-based generic advice with tips. The control group was a wait-list control condition, initially receiving no intervention. Intervention effects were tested with repeated-measures multivariate analysis of variance. The tailored intervention was successful in decreasing self-reported total workday sitting (time × group: P<.001), sitting at work (time × group: P<.001), and leisure time sitting (time × group: P=.03), and in increasing objectively measured breaks at work (time × group: P=.07); this was not the case in the other conditions. The changes in self-reported total nonworkday sitting, sitting during transport, television viewing, and personal computer use, objectively measured total sitting time, and sitting and standing time at work did not differ between conditions. Our results point out the significance of computer tailoring for sedentary behavior and its potential use in public health promotion, as the effects of the tailored condition were superior to the generic and control conditions. Clinicaltrials.gov NCT02672215; http://clinicaltrials.gov/ct2/show/NCT02672215 (Archived by WebCite at http://www.webcitation.org/6glPFBLWv).

The Effectiveness of a Web-Based Computer-Tailored Intervention on Workplace Sitting: A Randomized Controlled Trial

PubMed Central

De Bourdeaudhuij, Ilse; Cardon, Greet; Vandelanotte, Corneel

2016-01-01

Background Effective interventions to influence workplace sitting are needed, as office-based workers demonstrate high levels of continued sitting, and sitting too much is associated with adverse health effects. Therefore, we developed a theory-driven, Web-based, interactive, computer-tailored intervention aimed at reducing and interrupting sitting at work. Objective The objective of our study was to investigate the effects of this intervention on objectively measured sitting time, standing time, and breaks from sitting, as well as self-reported context-specific sitting among Flemish employees in a field-based approach. Methods Employees (n=213) participated in a 3-group randomized controlled trial that assessed outcomes at baseline, 1-month follow-up, and 3-month follow-up through self-reports. A subsample (n=122) were willing to wear an activity monitor (activPAL) from Monday to Friday. The tailored group received an automated Web-based, computer-tailored intervention including personalized feedback and tips on how to reduce or interrupt workplace sitting. The generic group received an automated Web-based generic advice with tips. The control group was a wait-list control condition, initially receiving no intervention. Intervention effects were tested with repeated-measures multivariate analysis of variance. Results The tailored intervention was successful in decreasing self-reported total workday sitting (time × group: P<.001), sitting at work (time × group: P<.001), and leisure time sitting (time × group: P=.03), and in increasing objectively measured breaks at work (time × group: P=.07); this was not the case in the other conditions. The changes in self-reported total nonworkday sitting, sitting during transport, television viewing, and personal computer use, objectively measured total sitting time, and sitting and standing time at work did not differ between conditions. Conclusions Our results point out the significance of computer tailoring for sedentary behavior and its potential use in public health promotion, as the effects of the tailored condition were superior to the generic and control conditions. Trial Registration Clinicaltrials.gov NCT02672215; http://clinicaltrials.gov/ct2/show/NCT02672215 (Archived by WebCite at http://www.webcitation.org/6glPFBLWv) PMID:27245789

A population based study on the night-time effect in trauma care.

PubMed

Di Bartolomeo, Stefano; Marino, Massimiliano; Ventura, Chiara; Trombetti, Susanna; De Palma, Rossana

2014-10-01

The so-called off hour effect-that is, increased mortality for patients admitted outside normal working hours-has never been demonstrated in trauma care. However, most of the studies excluded transferred cases. Because these patients are a special challenge for trauma systems, we hypothesised that their processes of care could be more sensitive to the off hour effect. The study design was retrospective, cohort and population based. We compared the mortality of all patients by daytime and night-time admittance to hospitals in an Italian region, with 4.5 million inhabitants, following a major injury in 2011. Logistic regression was used, adjusted for demographics and severity of injury (TMPM-ICD9), and stratified by transfer status. 1940 major trauma cases were included; 105 were acutely transferred. Night-time admission had a significant pejorative effect on mortality in the adjusted analysis (OR=1.49; 95% CI 1.05 to 2.11). This effect was most evident in transferred cases (OR=3.71; 95% CI 1.11 to 12.43). The night-time effect in trauma care was demonstrated for the first time and was maximal in transferred cases. This may explain why it was not found in previous studies where these patients were mostly excluded. Also, the use of population based data-whereby patients not accessing trauma centre care and presumably receiving poorer care were included-may have contributed to the findings. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Time and interference: Effects on working memory.

PubMed

Botto, Marta; Palladino, Paola

2016-05-01

This study tested predictions from the time-based resource-sharing (TBRS) model with a classical verbal working memory (WM) task, where target and non-target information interfere strongly with each other. Different predictions can be formulated according to the dominant perspectives (TBRS and interference hypothesis) on the role of inhibitory control in WM task performance. Here, we aimed to trace the activation of irrelevant information, examining priming effects in a lexical decision task immediately following WM recall. Results indicate the roles of both time and interference constraints in determining task performance. In particular, the role of time available seemed crucial at the highest WM loads (i.e., 3 and 4 memoranda). These were also associated with a higher activation of no-longer-relevant information but, in this case, independently from time available for processing. © 2015 The British Psychological Society.

Both bias and lack of knowledge influence organizational focus on first case of the day starts.

PubMed

Dexter, Elisabeth U; Dexter, Franklin; Masursky, Danielle; Garver, Michael P; Nussmeier, Nancy A

2009-04-01

The economic costs of reducing first case delays are often high, because efforts need to be applied to multiple operating rooms (ORs) simultaneously. Nevertheless, delays in starting first cases of the day are a common topic in OR committee meetings. We added three scientific questions to a 24 question online, anonymous survey performed before the implementation of a new OR information system. The 57 respondents cared sufficiently about OR management at the United States teaching hospital to complete all questions. The survey revealed reasons why personnel may focus on the small reductions in nonoperative time achievable by reducing tardiness in first cases of the day. (A) Respondents lacked knowledge about principles in reducing over-utilized OR time to increase OR efficiency, based on their answering the relevant question correctly at a rate no different from guessing at random. Those results differed from prior findings of responses at a rate worse than random, resulting from a bias on the day of surgery of making decisions that increase clinical work per unit time. (B) Most respondents falsely believed that a 10 min delay at the start of the day causes subsequent cases to start at least 10 min late (P < 0.0001 versus random chance). (C) Most respondents did not know that cases often take less time than scheduled (P = 0.008 versus chance). No one who demonstrated knowledge (C) about cases sometimes taking less time than scheduled applied that information to their response to (B) regarding cases starting late (P = 0.0002). Knowledge of OR efficiency was low among the respondents working in ORs. Nevertheless, the apparent absence of bias shows that education may influence behavior. In contrast, presence of bias on matters of tardiness of start times shows that education may be of no benefit. As the latter results match findings of previous studies of scheduling decisions, interventions to reduce patient and surgeon waiting from start times may depend principally on the application of automation to guide decision-making.

Progress Report on the Airborne Metadata and Time Series Working Groups of the 2016 ESDSWG

NASA Astrophysics Data System (ADS)

Evans, K. D.; Northup, E. A.; Chen, G.; Conover, H.; Ames, D. P.; Teng, W. L.; Olding, S. W.; Krotkov, N. A.

2016-12-01

NASA's Earth Science Data Systems Working Groups (ESDSWG) was created over 10 years ago. The role of the ESDSWG is to make recommendations relevant to NASA's Earth science data systems from users' experiences. Each group works independently focusing on a unique topic. Participation in ESDSWG groups comes from a variety of NASA-funded science and technology projects, including MEaSUREs and ROSS. Participants include NASA information technology experts, affiliated contractor staff and other interested community members from academia and industry. Recommendations from the ESDSWG groups will enhance NASA's efforts to develop long term data products. The Airborne Metadata Working Group is evaluating the suitability of the current Common Metadata Repository (CMR) and Unified Metadata Model (UMM) for airborne data sets and to develop new recommendations as necessary. The overarching goal is to enhance the usability, interoperability, discovery and distribution of airborne observational data sets. This will be done by assessing the suitability (gaps) of the current UMM model for airborne data using lessons learned from current and past field campaigns, listening to user needs and community recommendations and assessing the suitability of ISO metadata and other standards to fill the gaps. The Time Series Working Group (TSWG) is a continuation of the 2015 Time Series/WaterML2 Working Group. The TSWG is using a case study-driven approach to test the new Open Geospatial Consortium (OGC) TimeseriesML standard to determine any deficiencies with respect to its ability to fully describe and encode NASA earth observation-derived time series data. To do this, the time series working group is engaging with the OGC TimeseriesML Standards Working Group (SWG) regarding unsatisfied needs and possible solutions. The effort will end with the drafting of an OGC Engineering Report based on the use cases and interactions with the OGC TimeseriesML SWG. Progress towards finalizing recommendations will be presented at the meeting.

Antecedents and characteristics of lean thinking implementation in a Swedish hospital: a case study.

PubMed

Ulhassan, Waqar; Sandahl, Christer; Westerlund, Hugo; Henriksson, Peter; Bennermo, Marie; von Thiele Schwarz, Ulrica; Thor, Johan

2013-01-01

Despite the reported success of Lean in health care settings, it is unclear why and how organizations adopt Lean and how Lean transforms work design and, in turn, affects employees' work. This study investigated a cardiology department's journey to adopt and adapt Lean. The investigation was focused on the rationale and evolution of the Lean adoption to illuminate how a department with a long quality improvement history arrived at the decision to introduce Lean, and how Lean influenced employees' daily work. This is an explanatory single case study based on semistructured interviews, nonparticipant observations, and document studies. Guided by a Lean model, we undertook manifest content analysis of the data. We found that previous improvement efforts may facilitate the introduction of Lean but may be less important when forecasting whether Lean will be sustained over time. Contextual factors seemed to influence both what Lean tools were implemented and how well the changes were sustained. For example, adoption of Lean varied with the degree to which staff saw a need for change. Work redesign and teamwork were found helpful to improve patient care whereas problem solving was found helpful in keeping the staff engaged and sustaining the results over time.

Risk factors for recurrent episodes of care and work disability: case of low back pain.

PubMed

Wasiak, Radoslaw; Verma, Santosh; Pransky, Glenn; Webster, Barbara

2004-01-01

Recurrences of injuries are common and have significant socioeconomic consequences; it is important to identify associated risk factors as potential opportunities for prevention. This study was conducted to identify risk factors for low back pain (LBP) recurrence and the extent that variation in recurrence definition impacts identified risk factors. Patients with new claims for LBP reported in New Hampshire to a workers' compensation provider were selected (n = 2023) with a minimum of 3-year follow up. Alternative definitions of recurrence included a new episode of medical care and a new episode of lost work time (work disability). Risk factors better predicted disability-based than treatment-based recurrence. Longer durations of the initial episode of care or work disability were the most powerful predictors of recurrence, implying that shorter episodes of care and early return to work contribute to better outcomes.

Placing a Value on Academic Work: The Development and Implementation of a Time-Based Academic Workload Model

ERIC Educational Resources Information Center

Kenny, John; Fluck, Andrew; Jetson, Tim

2012-01-01

This paper presents a detailed case study of the development and implementation of a quantifiable academic workload model in the education faculty of an Australian university. Flowing from the enterprise bargaining process, the Academic Staff Agreement required the implementation of a workload allocation model for academics that was quantifiable…

Dynamic intraligamentary stabilization versus conventional ACL reconstruction: A matched study on return to work.

PubMed

Bieri, Kathrin S; Scholz, Stefan M; Kohl, Sandro; Aghayev, Emin; Staub, Lukas P

2017-06-01

The dynamic intraligamentary stabilization (DIS) technique is based on a different treatment approach than ACL reconstruction in that it intends to promote self-healing of the ligament. It is only recommended for acute injuries (<21days). The purpose of the present study was to compare DIS and ACLR with respect to the extent of work incapacity, revision rates, secondary arthroscopies, and treatment costs during recovery. The study was a post-hoc analysis of prospectively collected data in the Swiss National Accident Insurance Fund (SUVA) database. All registered DIS cases treated until 31 December 2012 were included in the study. ACLR cases were matched to DIS cases using a propensity score approach and analysed in a follow-up period of 2 years after injury. Paired Student's T-test and the Chi-square test were used to compare the outcome measures. All 53 DIS patients were matched to an ACLR pair. The mean time period from injury to surgery was 14days for DIS and 50days for ACLR (p<0.001). Overall work incapacity was 13% for DIS and 17% for ACLR resulting in a difference of nearly 1 month of absence from work (p=0.03). The course of postoperative work incapacity was very similar between the groups, while the work incapacity prior to surgery lower in the DIS group. We found no difference in treatment costs, secondary arthroscopies and revision rates. DIS patients benefited from nearly one month shorter absence from work than ACLR patients. This difference is likely related to the early surgical timing that is recommended for DIS. Since no differences were found between DIS and ACLR in terms of treatment costs, secondary arthroscopies and revision rates, the study supports the choice of DIS as an additional treatment option for acute ACL injuries. Further comparative studies are proposed to improve the evidence about optimal timing and best practice in ACL treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Legislative change enabling use of early part-time sick leave enhanced return to work and work participation in Finland.

PubMed

Viikari-Juntura, Eira; Virta, Lauri J; Kausto, Johanna; Autti-Rämö, Ilona; Martimo, Kari-Pekka; Laaksonen, Mikko; Leinonen, Taina; Husgafvel-Pursiainen, Kirsti; Burdorf, Alex; Solovieva, Svetlana

2017-09-01

Objectives The aim of the study was to assess the effectiveness of the use of part-time sick leave at the early (first 12 weeks) stage of work disability due to mental disorder or musculoskeletal disease on sustained return to work (RTW) and overall work participation. Methods In a nation-wide register-based quasi-experimental study, we compared sustained RTW (ie, ≥28 consecutive days at work) and 2-year work participation between the part- and full-time sickness absence (SA) benefit groups (N=1878 in each group) using propensity-score matching. Persons who received partial or full SA benefit due to musculoskeletal diseases or mental disorders between January 1, 2010 and December 31, 2011 were eligible as cases or controls, respectively. Results A higher proportion showed sustained RTW after part- compared to full-time sick leave [absolute risk difference 8.0%, 95% confidence interval (95% CI) 5.3-10.9]. Moreover, the proportion of time at work was at a 10.5% higher level in the part- compared to full-time sick leave group. The prevalence of full disability retirement was almost three-fold among the full- compared to part-time sick leave group, whereas partial disability retirement was 4.5-fold more prevalent in the part- compared to full-time sick leave group. Conclusions The use of part-time sick leave during the first three months of SA enhances RTW and overall work participation during two years among persons with mental disorders and musculoskeletal diseases. The prescription of part-time sick leave can be recommended at an early stage of work disability.

Complexity analysis of human physiological signals based on case studies

NASA Astrophysics Data System (ADS)

Angelova, Maia; Holloway, Philip; Ellis, Jason

2015-04-01

This work focuses on methods for investigation of physiological time series based on complexity analysis. It is a part of a wider programme to determine non-invasive markers for healthy ageing. We consider two case studies investigated with actigraphy: (a) sleep and alternations with insomnia, and (b) ageing effects on mobility patterns. We illustrate, using these case studies, the application of fractal analysis to the investigation of regulation patterns and control, and change of physiological function. In the first case study, fractal analysis techniques were implemented to study the correlations present in sleep actigraphy for individuals suffering from acute insomnia in comparison with healthy controls. The aim was to investigate if complexity analysis can detect the onset of adverse health-related events. The subjects with acute insomnia displayed significantly higher levels of complexity, possibly a result of too much activity in the underlying regulatory systems. The second case study considered mobility patterns during night time and their variations with age. It showed that complexity metrics can identify change in physiological function with ageing. Both studies demonstrated that complexity analysis can be used to investigate markers of health, disease and healthy ageing.

University of Wolverhampton Case Study: Embedding Practical Work-Based Modules into a Traditionally, Theoretical Programme

ERIC Educational Resources Information Center

Nicholls, Emma; Walsh, Margaret

2007-01-01

Purpose: This case study aims to provide a critical evaluation of the decision by the University of Wolverhampton's School of Legal Studies to develop a number of work-based learning modules, offered as part of the undergraduate programme. It seeks to examine why the School has taken the approach of embedding work-based learning into what has…

Improving general practice based epidemiologic surveillance using desktop clients: the French Sentinel Network experience.

PubMed

Turbelin, Clément; Boëlle, Pierre-Yves

2010-01-01

Web-based applications are a choice tool for general practice based epidemiological surveillance; however their use may disrupt the general practitioners (GPs) work process. In this article, we propose an alternative approach based on a desktop client application. This was developed for use in the French General Practitioners Sentinel Network. We developed a java application running as a client on the local GP computer. It allows reporting cases to a central server and provides feedback to the participating GPs. XML was used to describe surveillance protocols and questionnaires as well as instances of case descriptions. An evaluation of the users' feelings was carried out and the impact on the timeliness and completeness of surveillance data was measured. Better integration in the work process was reported, especially when the software was used at the time of consultation. Reports were received more frequently with less missing data. This study highlights the potential of allowing multiple ways of interaction with the surveillance system to increase participation of GPs and the quality of surveillance.

Equine grass sickness in Scotland: A case-control study of environmental geochemical risk factors.

PubMed

Wylie, C E; Shaw, D J; Fordyce, F M; Lilly, A; Pirie, R S; McGorum, B C

2016-11-01

We hypothesised that the apparent geographical distribution of equine grass sickness (EGS) is partly attributable to suboptimal levels of soil macro- and trace elements in fields where EGS occurs. If proven, altering levels of particular elements could be used to reduce the risk of EGS. To determine whether the geographical distribution of EGS cases in eastern Scotland is associated with the presence or absence of particular environmental chemical elements. Retrospective time-matched case-control study. This study used data for 455 geo-referenced EGS cases and 910 time-matched controls in eastern Scotland, and geo-referenced environmental geochemical data from the British Geological Survey Geochemical Baseline Survey of the Environment stream sediment (G-BASE) and the James Hutton Institute, National Soil Inventory of Scotland (NSIS) datasets. Multivariable statistical analyses identified clusters of three main elements associated with cases from (i) the G-BASE dataset - higher environmental Ti and lower Zn, and (ii) the NSIS dataset - higher environmental Ti and lower Cr. There was also some evidence from univariable analyses for lower Al, Cd, Cu, Ni and Pb and higher Ca, K, Mo, Na and Se environmental concentrations being associated with a case. Results were complicated by a high degree of correlation between most geochemical elements. The work presented here would appear to reflect soil- not horse-level risk factors for EGS, but due to the complexity of the correlations between elements, further work is required to determine whether these associations reflect causality, and consequently whether interventions to alter concentrations of particular elements in soil, or in grazing horses, could potentially reduce the risk of EGS. The effect of chemical elements on the growth of those soil microorganisms implicated in EGS aetiology also warrants further study. © 2015 The The Authors Equine Veterinary Journal © 2015 EVJ Ltd.

Computer aided fixture design - A case based approach

NASA Astrophysics Data System (ADS)

Tanji, Shekhar; Raiker, Saiesh; Mathew, Arun Tom

2017-11-01

Automated fixture design plays important role in process planning and integration of CAD and CAM. An automated fixture setup design system is developed where when fixturing surfaces and points are described allowing modular fixture components to get automatically select for generating fixture units and placed into position with satisfying assembled conditions. In past, various knowledge based system have been developed to implement CAFD in practice. In this paper, to obtain an acceptable automated machining fixture design, a case-based reasoning method with developed retrieval system is proposed. Visual Basic (VB) programming language is used in integrating with SolidWorks API (Application programming interface) module for better retrieval procedure reducing computational time. These properties are incorporated in numerical simulation to determine the best fit for practical use.

Negotiating accommodations so that work-based education facilitates career development for youth with disabilities.

PubMed

Hutchinson, Nancy L; Versnel, Joan; Chin, Peter; Munby, Hugh

2008-01-01

Workers with disabilities are entitled to have their individual needs accommodated in a way that allows them to perform the essential duties of their job. However, adults with disabilities are often lacking in career development and are ill-prepared to negotiate workplace accommodations. This has led educators to seek workplaces that can accommodate the needs of adolescents with disabilities, so these adolescents can learn to negotiate accommodations and enhance their career development through work-based education. This paper reports on two case studies in which employers had agreed to accommodate the needs of adolescents with disabilities participating in work-based education. Social Cognitive Career Theory (SCCT) framed the analyses of these two cases - a case of a student with physical disabilities and a case of a student with developmental disabilities. SCCT proves valuable in understanding the role of work-based education in the career development of disabled youth.

High-speed technique based on a parallel projection correlation procedure for digital image correlation

NASA Astrophysics Data System (ADS)

Zaripov, D. I.; Renfu, Li

2018-05-01

The implementation of high-efficiency digital image correlation methods based on a zero-normalized cross-correlation (ZNCC) procedure for high-speed, time-resolved measurements using a high-resolution digital camera is associated with big data processing and is often time consuming. In order to speed-up ZNCC computation, a high-speed technique based on a parallel projection correlation procedure is proposed. The proposed technique involves the use of interrogation window projections instead of its two-dimensional field of luminous intensity. This simplification allows acceleration of ZNCC computation up to 28.8 times compared to ZNCC calculated directly, depending on the size of interrogation window and region of interest. The results of three synthetic test cases, such as a one-dimensional uniform flow, a linear shear flow and a turbulent boundary-layer flow, are discussed in terms of accuracy. In the latter case, the proposed technique is implemented together with an iterative window-deformation technique. On the basis of the results of the present work, the proposed technique is recommended to be used for initial velocity field calculation, with further correction using more accurate techniques.

Warfarin monitoring in nursing homes assessed by case histories. Do recommendations and electronic alerts affect judgements?

PubMed

Teruel, Reyes Serrano; Thue, Geir; Fylkesnes, Svein Ivar; Sandberg, Sverre; Kristoffersen, Ann Helen

2017-09-01

Older adults treated with warfarin are prone to complications, and high-quality monitoring is essential. The aim of this case history based study was to assess the quality of warfarin monitoring in a routine situation, and in a situation with an antibiotic-warfarin interaction, before and after receiving an electronic alert. In April 2014, a national web-based survey with two case histories was distributed among Norwegian nursing home physicians and general practitioners working part-time in nursing homes. Case A represented a patient on stable warfarin treatment, but with a substantial INR increase within the therapeutic interval. Case B represented a more challenging patient with trimethoprim sulfamethoxazole (TMS) treatment due to pyelonephritis. In both cases, the physicians were asked to state the next warfarin dose and the INR recall interval. In case B, the physicians could change their suggestions after receiving an electronic alert on the TMS-warfarin interaction. Three hundred and ninety eight physicians in 292 nursing homes responded. Suggested INR recall intervals and warfarin doses varied substantially in both cases. In case A, 61% gave acceptable answers according to published recommendations, while only 9% did so for case B. Regarding the TMS-warfarin interaction in case history B, the electronic alert increased the percentage of respondents correctly suggesting a dose reduction from 29% to 53%. Having an INR instrument in the nursing home was associated with shortened INR recall times. Practical advice on handling of warfarin treatment and drug interactions is needed. Electronic alerts as presented in electronic medical records seem insufficient to change practice. Availability of INR instruments may be important regarding recall time.

Lack of generalizability of observational studies' findings for turnover time reduction and growth in surgery based on the State of Iowa, where from one year to the next, most growth was attributable to surgeons performing only a few cases per week.

PubMed

Dexter, Franklin; Jarvie, Craig; Epstein, Richard H

2018-02-01

Three observational studies at large teaching hospitals found that reducing turnover times resulted in the surgeons performing more cases. We sought to determine if these findings are generalizable to other hospitals, because, if so, reducing turnover times may be an important mechanism for hospitals to use for growing caseloads. Observational cohort study. 116 hospitals in Iowa with inpatient or outpatient surgery from July 1, 2013 through June 30, 2015. Surgeons in Iowa, each with a unique identifier among hospitals. The independent variable was the number of inpatient and outpatient cases that each surgeon performed each week during the first fiscal year beginning July 1, 2013. The dependent variables were surgeons' number of inpatient and outpatient surgical cases, and intraoperative work relative value units (RVU's) for outpatient cases, during the second fiscal year. The average hospital in Iowa had less than half of its growth from year 1 to year 2 in numbers of cases among surgeons who performed >2 cases per week in the baseline year (23.0%±2.5% [SE], P<0.0001 comparing mean to 50%). Less than half the growth in RVU's was among those surgeons (18.1%±2.2%, P<0.0001). The average hospital in Iowa had less than half of its growth in numbers of cases among surgeons who performed 2 or fewer cases per week at the hospital during the baseline year and >2 cases per week at other hospitals in the state during that year (24.4%±2.6%, P<0.0001). Less than half the growth in RVU's was among those surgeons (21.3%±2.5%, P<0.0001). Most (≥50%) annual growth in surgery, both based on the number of total inpatient and outpatient surgical cases, and on the total outpatient RVU's, was attributable to surgeons who performed 2 or fewer cases per week at each hospital statewide during the preceding year. Therefore, the strategic priority should be to assure that the many low-caseload surgeons have access to convenient OR time (e.g., by allocating sufficient OR time, and assigning surgeon blocks, in a mathematically sound, evidence-based way). Although reducing turnover times and anesthesia-controlled times to promote growth will be beneficial for a few surgeons, the effect on total caseload will be small. Copyright © 2017 Elsevier Inc. All rights reserved.

The remote controlling technique based on the serial port for SR-620 universal counter

NASA Astrophysics Data System (ADS)

Su, Jian-Feng; Chen, Shu-Fang; Li, Xiao-Hui; Wu, Hai-Tao; Bian, Yu-Jing

2004-12-01

The function of SR-620 universal counter and the remote work mode are introduced, and the remote controlling technique for the counter is analysed. A method to realize the remote controlling via the serial port for the counter is demonstrated, in which an ActiveX control is used. Besides, some points for attention in debugging are discussed based on the experience, and a case of program running for measuring time-delay is presented.

Lean principles optimize on-time vascular surgery operating room starts and decrease resident work hours.

PubMed

Warner, Courtney J; Walsh, Daniel B; Horvath, Alexander J; Walsh, Teri R; Herrick, Daniel P; Prentiss, Steven J; Powell, Richard J

2013-11-01

Lean process improvement techniques are used in industry to improve efficiency and quality while controlling costs. These techniques are less commonly applied in health care. This study assessed the effectiveness of Lean principles on first case on-time operating room starts and quantified effects on resident work hours. Standard process improvement techniques (DMAIC methodology: define, measure, analyze, improve, control) were used to identify causes of delayed vascular surgery first case starts. Value stream maps and process flow diagrams were created. Process data were analyzed with Pareto and control charts. High-yield changes were identified and simulated in computer and live settings prior to implementation. The primary outcome measure was the proportion of on-time first case starts; secondary outcomes included hospital costs, resident rounding time, and work hours. Data were compared with existing benchmarks. Prior to implementation, 39% of first cases started on time. Process mapping identified late resident arrival in preoperative holding as a cause of delayed first case starts. Resident rounding process inefficiencies were identified and changed through the use of checklists, standardization, and elimination of nonvalue-added activity. Following implementation of process improvements, first case on-time starts improved to 71% at 6 weeks (P = .002). Improvement was sustained with an 86% on-time rate at 1 year (P < .001). Resident rounding time was reduced by 33% (from 70 to 47 minutes). At 9 weeks following implementation, these changes generated an opportunity cost potential of $12,582. Use of Lean principles allowed rapid identification and implementation of perioperative process changes that improved efficiency and resulted in significant cost savings. This improvement was sustained at 1 year. Downstream effects included improved resident efficiency with decreased work hours. Copyright © 2013 Society for Vascular Surgery. Published by Mosby, Inc. All rights reserved.

[A survey on fatal work accidents based on Mortality Registry data: results of the Tuscany study on INAIL and RMR cases in the period 1992-2996].

PubMed

Chellini, Elisabetta; Baldasseroni, Alberto; Giovannetti, Lucia; Zoppi, Ombretta

2002-01-01

Work-related deaths are important "sentinel events" of unsuccessful prevention. In Italy the most exhaustive source of such events is the National Fund for Occupational Diseases (INAIL), but the amount of cases from this source seems to be underestimated due to the fact that it refers only to cases occurred to subjects insured by the Fund. A previous survey estimated the real amount of work-related deaths 10-20% higher than that quantified by INAIL. This study evaluated the contribute of the two most important sources (INAIL and the Regional Mortality Registry of Tuscany-RMR) in estimating the number of these cases in Tuscany in the period 1992-96. Cases were identified from each source, and then it was applied a capture-recapture method to size the cases from work-related accident different from road accidents. RMR appeared to be the most exhaustive source with 72.3% completeness versus 56.4% completeness of INAIL source. Nevertheless the last one must be considered the primary source, more specific and accurate, and since few years also timely, than any other one. Work-related deaths from road accident represent 35.9% of INAIL cases but they are difficult to be identified from RMR and were not considered in this study. In conclusion the mortality data should be used for an epidemiologic surveillance system on work-related deaths not due to road accident in order to identify cases occurred to subjects not insured by INAIL (and therefore not defined by the Fund). These deaths are also important in terms of public health. Cases identified only from RMR, occurred in Tuscany in 1992-96, were 155: the vast majority occurred to farmers (mainly pensioners, and due to caterpillar upsetting), to bricklayers, to railway workers, to soldiers and to entrepreneurs.

Training in time-limited dynamic psychotherapy: A systematic comparison of pre- and post-training cases treated by one therapist.

PubMed

Anderson, Timothy; Strupp, Hans H

2015-01-01

This qualitative study systematically compared cases treated by the same therapist in order to understand the group comparison findings of a larger study on training of experienced therapists (the "Vanderbilt II" psychotherapy project). The therapist, Dr C., was selected based on the therapist's overall treatment successes. His two patients were selected based on their outcomes and the relative training cohort from which they were drawn: a case with successful outcome from the pre-training cohort and a case of negligible improvement from the post-training cohort. Dr C. demonstrated a variety of interpersonal skills throughout his pre-training case, though there was also poor interpersonal process throughout. However, in the second case he had considerable difficulty in adapting his typical therapeutic approach to the requirements of the time-limited dynamic psychotherapy (TLDP) manual, even while appearing to work hard to find ways to use the manual. Dr C.'s spontaneity, and his unique set of interpersonal skills may enhanced his initial rapport and alliance building with clients and yet may not have interfaced well with TLDP. His unique interpersonal skills also may have contributed to problems of interpersonal process. Future research may benefit from examining the interaction of between therapist interpersonal skills and the implementation of the treatment manual.

Redesign links CMs, primary care.

PubMed

2013-12-01

At WellSpan Health, teams that include hospital-based case managers and social workers, and health coaches located in physician offices, work together to coordinate care. The case managers and social workers are assigned by physician and spend most of their time in the hospital, but are expected to spend a target of two hours a week at the WellSpan Medical Group physician practices. Practices that are not part of the WellSpan Medical Group are assigned a case manager and a social worker who follow their patients in the hospital but do not visit the practice. The initiative promotes communication and collaboration between the hospital level of care and primary care.

Dramatic dwindling of the power spectrum of high order harmonics by shrinking of the gap size in bowtie nanostructures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hosseinzadeh, F.; Batebi, S., E-mail: s-batebi@guilan.ac.ir; Soofi, M. Q.

2017-03-15

Our work is based on high harmonic generation in a gaseous medium (helium ion), by exploiting gold bowtie nanostructures as laser field amplifiers. As the result of emission of a laser pulse, the wave function of the atom varies with time; so, it is necessary to solve 1D time-dependent Schrödinger equation by means of split operator method. By illumination of a short duration, long wavelength three color laser pulse inside the gap, the enhanced field not only changes with time, but also varies in space. In this work we considered this space inhomogeneity in linear and nonlinear schemes. We showmore » that in nonlinear case, the plateau region is more extended. We also show that in larger gaps, cutoff occurs on higher frequencies. But limitation of electron motion in bowtie nanostructures leads to the choice of an optimum 16 nm gap size in our case. We predict that, by the superposition of supercontinuum harmonics, a 26 attosecond pulse can be generated.« less

Arts as an ecological method to enhance quality of work experience of healthcare staff: a phenomenological-hermeneutic study

PubMed Central

Bojner Horwitz, Eva; Grape Viding, Christina; Rydwik, Elisabeth; Huss, Ephrat

2017-01-01

ABSTRACT This paper explores the impact of self-chosen arts-based recreational activities, as opposed to the traditional arts therapy activities, on the well-being of healthcare providers. Three qualitative case studies of programs in which arts-based activities were used to work with healthcare providers, lasting for 10 weeks each, are phenomenological-hermeneutically evaluated using interviews and focus groups. The findings show what we refer to as an “ecological” ripple of effects: (1) the arts-based activities helped to reduce individual stress and to enhance mood over time, (2) the activities helped to transform workplace relationships within wards, and (3) the arts humanized the overall work climate in the healthcare setting. These effects go beyond those of using the art production as a strategy for stress reduction and imply potential for a more encompassing role for the arts within healthcare. PMID:28609216

Does case-mix based reimbursement stimulate the development of process-oriented care delivery?

PubMed

Vos, Leti; Dückers, Michel L A; Wagner, Cordula; van Merode, Godefridus G

2010-11-01

Reimbursement based on the total care of a patient during an acute episode of illness is believed to stimulate management and clinicians to reduce quality problems like waiting times and poor coordination of care delivery. Although many studies already show that this kind of case-mix based reimbursement leads to more efficiency, it remains unclear whether care coordination improved as well. This study aims to explore whether case-mix based reimbursement stimulates development of care coordination by the use of care programmes, and a process-oriented way of working. Data for this study were gathered during the winter of 2007/2008 in a survey involving all Dutch hospitals. Descriptive and structural equation modelling (SEM) analyses were conducted. SEM reveals that adoption of the case-mix reimbursement within hospitals' budgeting processes stimulates hospitals to establish care programmes by the use of process-oriented performance measures. However, the implementation of care programmes is not (yet) accompanied by a change in focus from function (the delivery of independent care activities) to process (the delivery of care activities as being connected to a chain of interdependent care activities). This study demonstrates that hospital management can stimulate the development of care programmes by the adoption of case-mix reimbursement within hospitals' budgeting processes. Future research is recommended to confirm this finding and to determine whether the establishment of care programmes will in time indeed lead to a more process-oriented view of professionals. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Addressing the Barriers to Agile Development in DoD

DTIC Science & Technology

2015-05-01

Acquisition Small, Frequent Releases Iteratively Developed Review Working Software Vice Extensive Docs Responsive to Changes...Distribution Unlimited. Case Number 15-1457’ JCIDS IT Box Model  Streamlined requirements process for software >$15M  JROC approves IS-ICD...Services (FAR Part 37) Product-based Pay for the time and expertise of an Agile development contractor Contract for a defined software delivery

Strategic Brain Drain: Implications for Higher Education in Oman

ERIC Educational Resources Information Center

Al-Barwani, Thuwayba; Chapman, David W.; Ameen, Hana

2009-01-01

Oman will soon be producing three times more college graduates than there are jobs available in the country each year, forcing graduates to seek employment outside of Oman. Their success in securing and holding employment will be based more on training and performance than might be the case if they were working in Oman. If graduates find that the…

Establishing treatment protocols for clinical mastitis.

PubMed

Roberson, Jerry R

2003-03-01

Each farm has a unique mix of mastitis pathogens and management procedures that have evolved over time. The herd veterinarian should work with the manager/owner to systematically develop treatment protocols that meet the needs and management of the farm. To establish a mastitis treatment protocol, it is necessary to develop a system to routinely identify clinical mastitis cases, develop a herd-specific severity level assessment system, manage the clinical mastitis cases based on severity level and culture result (when available), avoid antibiotic residues, and monitor the success of the system and alter the protocol as necessary.

CyberPetri at CDX 2016: Real-time Network Situation Awareness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arendt, Dustin L.; Best, Daniel M.; Burtner, Edwin R.

CyberPetri is a novel visualization technique that provides a flexible map of the network based on available characteristics, such as IP address, operating system, or service. Previous work introduced CyberPetri as a visualization feature in Ocelot, a network defense tool that helped security analysts understand and respond to an active defense scenario. In this paper we present a case study in which we use the CyberPetri visualization technique to support real-time situation awareness during the 2016 Cyber Defense Exercise.

An embedded real-time red peach detection system based on an OV7670 camera, ARM cortex-M4 processor and 3D look-up tables.

PubMed

Teixidó, Mercè; Font, Davinia; Pallejà, Tomàs; Tresanchez, Marcel; Nogués, Miquel; Palacín, Jordi

2012-10-22

This work proposes the development of an embedded real-time fruit detection system for future automatic fruit harvesting. The proposed embedded system is based on an ARM Cortex-M4 (STM32F407VGT6) processor and an Omnivision OV7670 color camera. The future goal of this embedded vision system will be to control a robotized arm to automatically select and pick some fruit directly from the tree. The complete embedded system has been designed to be placed directly in the gripper tool of the future robotized harvesting arm. The embedded system will be able to perform real-time fruit detection and tracking by using a three-dimensional look-up-table (LUT) defined in the RGB color space and optimized for fruit picking. Additionally, two different methodologies for creating optimized 3D LUTs based on existing linear color models and fruit histograms were implemented in this work and compared for the case of red peaches. The resulting system is able to acquire general and zoomed orchard images and to update the relative tracking information of a red peach in the tree ten times per second.

An Embedded Real-Time Red Peach Detection System Based on an OV7670 Camera, ARM Cortex-M4 Processor and 3D Look-Up Tables

PubMed Central

Teixidó, Mercè; Font, Davinia; Pallejà, Tomàs; Tresanchez, Marcel; Nogués, Miquel; Palacín, Jordi

2012-01-01

This work proposes the development of an embedded real-time fruit detection system for future automatic fruit harvesting. The proposed embedded system is based on an ARM Cortex-M4 (STM32F407VGT6) processor and an Omnivision OV7670 color camera. The future goal of this embedded vision system will be to control a robotized arm to automatically select and pick some fruit directly from the tree. The complete embedded system has been designed to be placed directly in the gripper tool of the future robotized harvesting arm. The embedded system will be able to perform real-time fruit detection and tracking by using a three-dimensional look-up-table (LUT) defined in the RGB color space and optimized for fruit picking. Additionally, two different methodologies for creating optimized 3D LUTs based on existing linear color models and fruit histograms were implemented in this work and compared for the case of red peaches. The resulting system is able to acquire general and zoomed orchard images and to update the relative tracking information of a red peach in the tree ten times per second. PMID:23202040

Can Work-Based Learning Add to the Research Inventory of Higher Education? The Case of Collaborative Research

ERIC Educational Resources Information Center

Portwood, Derek

2007-01-01

Work-based learning's preoccupation with developing award-bearing programmes has affected the scope and style of work-based research. While offering development opportunities for work-based research, the emphasis of work-based learning programmes on the individual learner has curtailed the use of collaborative research. This article explores how…

Combining Model-Based and Feature-Driven Diagnosis Approaches - A Case Study on Electromechanical Actuators

NASA Technical Reports Server (NTRS)

Narasimhan, Sriram; Roychoudhury, Indranil; Balaban, Edward; Saxena, Abhinav

2010-01-01

Model-based diagnosis typically uses analytical redundancy to compare predictions from a model against observations from the system being diagnosed. However this approach does not work very well when it is not feasible to create analytic relations describing all the observed data, e.g., for vibration data which is usually sampled at very high rates and requires very detailed finite element models to describe its behavior. In such cases, features (in time and frequency domains) that contain diagnostic information are extracted from the data. Since this is a computationally intensive process, it is not efficient to extract all the features all the time. In this paper we present an approach that combines the analytic model-based and feature-driven diagnosis approaches. The analytic approach is used to reduce the set of possible faults and then features are chosen to best distinguish among the remaining faults. We describe an implementation of this approach on the Flyable Electro-mechanical Actuator (FLEA) test bed.

Communication and collaboration among return-to-work stakeholders.

PubMed

Russell, Elizabeth; Kosny, Agnieszka

2018-05-17

Workers who are injured or become ill on the job are best able to return-to-work when stakeholders involved in their case collaborate and communicate. This study examined health care providers' and case managers' engagement in rehabilitation and return-to-work following workplace injury or illness. In-depth interviews were conducted with 97 health care providers and 34 case managers in four Canadian provinces about their experiences facilitating rehabilitation and return-to-work, and interacting with system stakeholders. A qualitative thematic content analysis demonstrated two key findings. Firstly, stakeholders were challenged to collaborate as a result of: barriers to interdisciplinary and cross-professional communication; philosophical differences about the timing and appropriateness of return-to-work; and confusion among health care providers about the workers' compensation system. Secondly, these challenges adversely affected the co-ordination of patient care, and consequentially, injured workers often became information conduits, and effective and timely treatment and return-to-work was sometimes negatively impacted. Communication challenges between health care providers and case managers may negatively impact patient care and alienate treating health care providers. Discussion about role clarification, the appropriateness of early return-to-work, how paperwork shapes health care providers' role expectations, and strengthened inter-professional communication are considered. Implications for Rehabilitation Administrative and conceptual barriers in workers' compensation systems challenge collaboration and communication between health care providers and case managers. Injured workers may become conduits of incorrect information, resulting in adversarial relationships, overturned health care providers' recommendations, and their disengagement from rehabilitation and return-to-work. Stakeholders should clarify the role of health care providers during rehabilitation and return-to-work and the appropriateness of early return-to-work to mitigate recurring challenges. Communication procedures between health care specialists may disrupt these challenges, increasing the likelihood of timely and effective rehabilitation and return-to-work.

Monte Carlo grain growth modeling with local temperature gradients

NASA Astrophysics Data System (ADS)

Tan, Y.; Maniatty, A. M.; Zheng, C.; Wen, J. T.

2017-09-01

This work investigated the development of a Monte Carlo (MC) simulation approach to modeling grain growth in the presence of non-uniform temperature field that may vary with time. We first scale the MC model to physical growth processes by fitting experimental data. Based on the scaling relationship, we derive a grid site selection probability (SSP) function to consider the effect of a spatially varying temperature field. The SSP function is based on the differential MC step, which allows it to naturally consider time varying temperature fields too. We verify the model and compare the predictions to other existing formulations (Godfrey and Martin 1995 Phil. Mag. A 72 737-49 Radhakrishnan and Zacharia 1995 Metall. Mater. Trans. A 26 2123-30) in simple two-dimensional cases with only spatially varying temperature fields, where the predicted grain growth in regions of constant temperature are expected to be the same as for the isothermal case. We also test the model in a more realistic three-dimensional case with a temperature field varying in both space and time, modeling grain growth in the heat affected zone of a weld. We believe the newly proposed approach is promising for modeling grain growth in material manufacturing processes that involves time-dependent local temperature gradient.

[Study on the ARIMA model application to predict echinococcosis cases in China].

PubMed

En-Li, Tan; Zheng-Feng, Wang; Wen-Ce, Zhou; Shi-Zhu, Li; Yan, Lu; Lin, Ai; Yu-Chun, Cai; Xue-Jiao, Teng; Shun-Xian, Zhang; Zhi-Sheng, Dang; Chun-Li, Yang; Jia-Xu, Chen; Wei, Hu; Xiao-Nong, Zhou; Li-Guang, Tian

2018-02-26

To predict the monthly reported echinococcosis cases in China with the autoregressive integrated moving average (ARIMA) model, so as to provide a reference for prevention and control of echinococcosis. SPSS 24.0 software was used to construct the ARIMA models based on the monthly reported echinococcosis cases of time series from 2007 to 2015 and 2007 to 2014, respectively, and the accuracies of the two ARIMA models were compared. The model based on the data of the monthly reported cases of echinococcosis in China from 2007 to 2015 was ARIMA (1, 0, 0) (1, 1, 0) 12 , the relative error among reported cases and predicted cases was -13.97%, AR (1) = 0.367 ( t = 3.816, P < 0.001), SAR (1) = -0.328 ( t = -3.361, P = 0.001), and Ljung-Box Q = 14.119 ( df = 16, P = 0.590) . The model based on the data of the monthly reported cases of echinococcosis in China from 2007 to 2014 was ARIMA (1, 0, 0) (1, 0, 1) 12 , the relative error among reported cases and predicted cases was 0.56%, AR (1) = 0.413 ( t = 4.244, P < 0.001), SAR (1) = 0.809 ( t = 9.584, P < 0.001), SMA (1) = 0.356 ( t = 2.278, P = 0.025), and Ljung-Box Q = 18.924 ( df = 15, P = 0.217). The different time series may have different ARIMA models as for the same infectious diseases. It is needed to be further verified that the more data are accumulated, the shorter time of predication is, and the smaller the average of the relative error is. The establishment and prediction of an ARIMA model is a dynamic process that needs to be adjusted and optimized continuously according to the accumulated data, meantime, we should give full consideration to the intensity of the work related to infectious diseases reported (such as disease census and special investigation).

Optimizing the real-time ground level enhancement alert system based on neutron monitor measurements: Introducing GLE Alert Plus

NASA Astrophysics Data System (ADS)

Souvatzoglou, G.; Papaioannou, A.; Mavromichalaki, H.; Dimitroulakos, J.; Sarlanis, C.

2014-11-01

Whenever a significant intensity increase is being recorded by at least three neutron monitor stations in real-time mode, a ground level enhancement (GLE) event is marked and an automated alert is issued. Although, the physical concept of the algorithm is solid and has efficiently worked in a number of cases, the availability of real-time data is still an open issue and makes timely GLE alerts quite challenging. In this work we present the optimization of the GLE alert that has been set into operation since 2006 at the Athens Neutron Monitor Station. This upgrade has led to GLE Alert Plus, which is currently based upon the Neutron Monitor Database (NMDB). We have determined the critical values per station allowing us to issue reliable GLE alerts close to the initiation of the event while at the same time we keep the false alert rate at low levels. Furthermore, we have managed to treat the problem of data availability, introducing the Go-Back-N algorithm. A total of 13 GLE events have been marked from January 2000 to December 2012. GLE Alert Plus issued an alert for 12 events. These alert times are compared to the alert times of GOES Space Weather Prediction Center and Solar Energetic Particle forecaster of the University of Málaga (UMASEP). In all cases GLE Alert Plus precedes the GOES alert by ≈8-52 min. The comparison with UMASEP demonstrated a remarkably good agreement. Real-time GLE alerts by GLE Alert Plus may be retrieved by http://cosray.phys.uoa.gr/gle_alert_plus.html, http://www.nmdb.eu, and http://swe.ssa.esa.int/web/guest/space-radiation. An automated GLE alert email notification system is also available to interested users.

BladeRunners and Picasso Cafe: A Case Study Evaluation of Two Work-Based Training Programs for Disadvantaged Youth.

ERIC Educational Resources Information Center

Currie, Sheila; Foley, Kelly; Schwartz, Saul; Taylor-Lewis, Musu

In 1998, Canada's Social Research and Demonstration Corporation (SRDC) conducted case studies of two work-based training and skill development programs for street youth in Vancouver, British Columbia. The BladeRunners program places youth on construction sites while encouraging them to work toward an apprenticeship in the building trades. The…

A "CASE" Study on Developing Science Communication and Outreach Skills of University Graduate Student Researchers in Alaska

NASA Astrophysics Data System (ADS)

Tedesche, M. E.; Conner, L.

2015-12-01

Well rounded scientific researchers are not only experts in their field, but can also communicate their work to a multitude of various audiences, including the general public and undergraduate university students. Training in these areas should ideally start during graduate school, but many programs are not preparing students to effectively communicate their work. Here, we present results from the NSF-funded CASE (Changing Alaska Science Education) program, which was funded by NSF under the auspices of the GK-12 program. CASE placed science graduate students (fellows) in K-12 classrooms to teach alongside of K-12 teachers with the goal of enhancing communication and teaching skills among graduate students. CASE trained fellows in inquiry-based and experiential techniques and emphasized the integration of art, writing, and traditional Alaska Native knowledge in the classroom. Such techniques are especially effective in engaging students from underrepresented groups. As a result of participation, many CASE fellows have reported increased skills in communication and teaching, as well as in time management. These skills may prove directly applicable to higher education when teaching undergraduate students.

Flex-Time. A Catalyst Occasional Paper.

ERIC Educational Resources Information Center

Catalyst, New York, NY.

Contains history, case studies, and discussion of the use and benefits of flex-time employment, a pattern of working hours in which individual employees begin and end their work day at times of their choice, within certain limits, as long as they work a prescribed number of hours. The paper addresses the following topics: (1) What is flex-time,…

Intelligent Transportation Systems in Work Zones - A Case Study: Work Zone Travel Time System. Reducing Congestion with the Use of a Traffic Management Contract Incentive during the Reconstruction of Arizona State Route 68

DOT National Transportation Integrated Search

2004-10-01

This case study is one in a series of documents that examines the use of Intelligent Transportation Systems (ITS) in work zones. This case study presents information gathered through interviews with key personnel on the Arizona State Route (SR) 68 pr...

Piloting a Collaborative Web-Based System for Testing ICD-11.

PubMed

Donada, Marc; Kostanjsek, Nenad; Della Mea, Vincenzo; Celik, Can; Jakob, Robert

2017-01-01

The 11^th revision of the International Classification of Diseases (ICD-11), for the first time in ICD history, deployed web-based collaboration of experts and ICT tools. To ensure that ICD-11 is working well, it needs to be systematically field tested in different settings, across the world. This will be done by means of a number of experiments. In order to support its implementation, a web-based system (ICDfit) has been designed and developed. The present paper illustrates the current prototype of the system and its technical testing. the system has been designed according to WHO requirements, and implemented using PHP and MySQL. Then, a preliminary technical test has been designed and run in January 2016, involving 8 users. They had to carry out double coding, that is, coding case summaries with both ICD-10 and ICD-11, and answering quick questions on the coding difficulty. the 8 users coded 632 cases each, spending an average of 163 seconds per case. While we found an issue in the mechanism used to record coding times, no further issues were found. the proposed system seems to be technically adequate for supporting future ICD-11 testing.

Jobs to Manufacturing Careers: Work-Based Courses. Work-Based Learning in Action

ERIC Educational Resources Information Center

Kobes, Deborah

2016-01-01

This case study, one of a series of publications exploring effective and inclusive models of work-based learning, finds that work-based courses bring college to the production line by using the job as a learning lab. Work-based courses are an innovative way to give incumbent workers access to community college credits and degrees. They are…

Study of the performances of nano-case treatment cutting tools on carbon steel work material during turning operation

NASA Astrophysics Data System (ADS)

Afolalu, S. A.; Okokpujie, I. P.; Salawu, E. Y.; Abioye, A. A.; Abioye, O. P.; Ikumapayi, O. M.

2018-04-01

The degree of holding temperature and time play a major role in nano-case treatment of cutting tools which immensely contributed to its performance during machining operation. The objective of this research work is to carryout comparative study of performance of nano-case treatment tools developed using low and medium carbon steel as work piece. Turning operation was carried out under two different categories with specific work piece on universal lathe machine using HSS cutting tools 100 mm × 12mm × 12mm that has been nano-case treated under varying conditions of temperatures and timeof 800,850, 900, 950°C and 60, 90, 120 mins respectively. The turning parameters used in evaluating this experiment were cutting speed of 270, 380 and 560mm/min, feed rate of 0.15, 0.20 and 0.25 mm/min, depth of cut of 2mm, work piece diameter of 25mm and rake angle of 7° each at three levels. The results of comparative study of their performances revealed that the timespent in the machining of low carbon steel material at a minimum temperature and time of 800°C, 60 mins were1.50, 2.17 mins while at maximum temperature and time of 950°C, 120 mins were 1.19, 2.02 mins. It was also observed that at a corresponding constant speed of 270,380 and 560mm/min at higher temperature and time, a relative increased in the length of cut were observed. Critical observation of the result showed that at higher case hardening temperature and time (950°C/120mins), the HSS cutting tool gave a better performance as lesser time was consumed during the turning operation.

Linear time-dependent reference intervals where there is measurement error in the time variable-a parametric approach.

PubMed

Gillard, Jonathan

2015-12-01

This article re-examines parametric methods for the calculation of time specific reference intervals where there is measurement error present in the time covariate. Previous published work has commonly been based on the standard ordinary least squares approach, weighted where appropriate. In fact, this is an incorrect method when there are measurement errors present, and in this article, we show that the use of this approach may, in certain cases, lead to referral patterns that may vary with different values of the covariate. Thus, it would not be the case that all patients are treated equally; some subjects would be more likely to be referred than others, hence violating the principle of equal treatment required by the International Federation for Clinical Chemistry. We show, by using measurement error models, that reference intervals are produced that satisfy the requirement for equal treatment for all subjects. © The Author(s) 2011.

Molecular Analysis of Spinal Muscular Atrophy: A genotyping protocol based on TaqMan(®) real-time PCR.

PubMed

de Souza Godinho, Fernanda Marques; Bock, Hugo; Gheno, Tailise Conte; Saraiva-Pereira, Maria Luiza

2012-12-01

Spinal muscular atrophy (SMA) is an autosomal recessive inherited disorder caused by alterations in the survival motor neuron I (SMN1) gene. SMA patients are classified as type I-IV based on severity of symptoms and age of onset. About 95% of SMA cases are caused by the homozygous absence of SMN1 due to gene deletion or conversion into SMN2. PCR-based methods have been widely used in genetic testing for SMA. In this work, we introduce a new approach based on TaqMan(®)real-time PCR for research and diagnostic settings. DNA samples from 100 individuals with clinical signs and symptoms suggestive of SMA were analyzed. Mutant DNA samples as well as controls were confirmed by DNA sequencing. We detected 58 SMA cases (58.0%) by showing deletion of SMN1 exon 7. Considering clinical information available from 56 of them, the patient distribution was 26 (46.4%) SMA type I, 16 (28.6%) SMA type II and 14 (25.0%) SMA type III. Results generated by the new method was confirmed by PCR-RFLP and by DNA sequencing when required. In conclusion, a protocol based on real-time PCR was shown to be effective and specific for molecular analysis of SMA patients.

The virtual continuity in learning programme: results.

PubMed

Wood, Eleanor; Tso, Simon

2012-08-01

The implementation of the European Working Time Directive and specialty-driven care has resulted in the loss of continuity of patient care, and thus a loss of continuity in learning. We proposed a potential solution to this fragmentation of junior doctor workplace learning in the Virtual Continuity in Learning Programme (VCLP). The VCLP enables the doctor to follow the virtual patient journey (of an actual patient who is no longer under their care) using the Virtual Consulting Room (VcR), and to understand the rationale behind clinical decision making prior to completing their case-based discussion (CbD) work-based assessments. Fifty-seven out of 62 (92%) of foundation doctors (Homerton University Hospital, London, UK) consented to participate in the study. Web-tracking software was used. Fifty-three out of 57 (93%) doctors completed an initial questionnaire. Twenty-nine out of 57 (51%) doctors returned a follow-up questionnaire 6 months later. Eleven doctors were interviewed in three focus groups: the VcR user group; the VcR non-user group; and a mixed group. The data was analysed qualitatively. Tracking showed 33.3 per cent (19/57) of doctors used the VcR over a 6-month period. Interestingly doctors used the VcR in a range of situations, not solely as instructed. Results enabled us to understand how doctors learn and their perception of using the VCLP to support their learning and completion of work-based assessments. Foundation doctors use the educational resources available, including the VcR, to help structure their workplace learning. The majority of VcR users found it particularly useful for just-in-time learning. The VCLP offers support to junior doctors learning during their preparation for case-based discussion. © Blackwell Publishing Ltd 2012.

Comparison of 2015 Medicare relative value units for gender-specific procedures: Gynecologic and gynecologic-oncologic versus urologic CPT coding. Has time healed gender-worth?

PubMed

Benoit, M F; Ma, J F; Upperman, B A

2017-02-01

In 1992, Congress implemented a relative value unit (RVU) payment system to set reimbursement for all procedures covered by Medicare. In 1997, data supported that a significant gender bias existed in reimbursement for gynecologic compared to urologic procedures. The present study was performed to compare work and total RVU's for gender specific procedures effective January 2015 and to evaluate if time has healed the gender-based RVU worth. Using the 2015 CPT codes, we compared work and total RVU's for 50 pairs of gender specific procedures. We also evaluated 2015 procedure related provider compensation. The groups were matched so that the procedures were anatomically similar. We also compared 2015 to 1997 RVU and fee schedules. Evaluation of work RVU's for the paired procedures revealed that in 36 cases (72%), male vs female procedures had a higher wRVU and tRVU. For total fee/reimbursement, 42 (84%) male based procedures were compensated at a higher rate than the paired female procedures. On average, male specific surgeries were reimbursed at an amount that was 27.67% higher for male procedures than for female-specific surgeries. Female procedure based work RVU's have increased minimally from 1997 to 2015. Time and effort have trended towards resolution of some gender-related procedure worth discrepancies but there are still significant RVU and compensation differences that should be further reviewed and modified as surgical time and effort highly correlate. Copyright © 2016. Published by Elsevier Inc.

Ranking streamflow model performance based on Information theory metrics

NASA Astrophysics Data System (ADS)

Martinez, Gonzalo; Pachepsky, Yakov; Pan, Feng; Wagener, Thorsten; Nicholson, Thomas

2016-04-01

The accuracy-based model performance metrics not necessarily reflect the qualitative correspondence between simulated and measured streamflow time series. The objective of this work was to use the information theory-based metrics to see whether they can be used as complementary tool for hydrologic model evaluation and selection. We simulated 10-year streamflow time series in five watersheds located in Texas, North Carolina, Mississippi, and West Virginia. Eight model of different complexity were applied. The information-theory based metrics were obtained after representing the time series as strings of symbols where different symbols corresponded to different quantiles of the probability distribution of streamflow. The symbol alphabet was used. Three metrics were computed for those strings - mean information gain that measures the randomness of the signal, effective measure complexity that characterizes predictability and fluctuation complexity that characterizes the presence of a pattern in the signal. The observed streamflow time series has smaller information content and larger complexity metrics than the precipitation time series. Watersheds served as information filters and and streamflow time series were less random and more complex than the ones of precipitation. This is reflected the fact that the watershed acts as the information filter in the hydrologic conversion process from precipitation to streamflow. The Nash Sutcliffe efficiency metric increased as the complexity of models increased, but in many cases several model had this efficiency values not statistically significant from each other. In such cases, ranking models by the closeness of the information-theory based parameters in simulated and measured streamflow time series can provide an additional criterion for the evaluation of hydrologic model performance.

Virtual patients in the acquisition of clinical reasoning skills: does presentation mode matter? A quasi-randomized controlled trial.

PubMed

Schubach, Fabian; Goos, Matthias; Fabry, Götz; Vach, Werner; Boeker, Martin

2017-09-15

The objective of this study is to compare two different instructional methods in the curricular use of computerized virtual patients in undergraduate medical education. We aim to investigate whether using many short and focused cases - the key feature principle - is more effective for the learning of clinical reasoning skills than using few long and systematic cases. We conducted a quasi-randomized, non-blinded, controlled parallel-group intervention trial in a large medical school in Southwestern Germany. During two seminar sessions, fourth- and fifth-year medical students (n = 56) worked on the differential diagnosis of the acute abdomen. The educational tool - virtual patients - was the same, but the instructional method differed: In one trial arm, students worked on multiple short cases, with the instruction being focused only on important elements ("key feature arm", n = 30). In the other trial arm, students worked on few long cases, with the instruction being comprehensive and systematic ("systematic arm", n = 26). The overall training time was the same in both arms. The students' clinical reasoning capacity was measured by a specifically developed instrument, a script concordance test. Their motivation and the perceived effectiveness of the instruction were assessed using a structured evaluation questionnaire. Upon completion of the script concordance test with a reference score of 80 points and a standard deviation of 5 for experts, students in the key feature arm attained a mean of 57.4 points (95% confidence interval: 50.9-63.9), and in the systematic arm, 62.7 points (57.2-68.2), with Cohen's d at 0.337. The difference is statistically non-significant (p = 0.214). In the evaluation survey, students in the key feature arm indicated that they experienced more time pressure and perceived the material as more difficult. In this study powered for a medium effect, we could not provide empirical evidence for the hypothesis that a key feature-based instruction on multiple short cases is superior to a systematic instruction on few long cases in the curricular implementation of virtual patients. The results of the evaluation survey suggest that learners should be given enough time to work through case examples, and that caution should be taken to prevent cognitive overload.

Negotiating therapeutic alliances with a family at impasse.

PubMed

Friedlander, Myrna L; Lee, Hsin-Hua; Shaffer, Katharine S; Cabrera, Patricia

2014-03-01

To bridge the science-practice gap, the APA Presidential Task Force endorsed the publication of evidence-based case studies, but to date, there have been few such investigations of conjoint family therapy. To fill this gap, we studied a successful case of treatment-as-usual in a community agency. Owing to the complexity of the working alliance in conjoint therapy, we examined how an experienced family therapist managed to develop and sustain multiple alliances over time with an estranged couple in crisis. The outcome data showed clinically meaningful changes as well as high satisfaction levels and notable declines in the target complaint discomfort levels of all family members. Alliance indicators showed that the therapist worked diligently over time to connect emotionally with each family member and to foster and maintain safety. Session impact scores showed consistently deep sessions but more variability in smoothness. By working toward the only shared treatment goal-to repair each parent's individual relationship with their very angry daughter-the therapist was able to reduce the effect of the marital estrangement on the child. At the end of the 10 contracted family sessions, the parents agreed to begin working on their relationship in couples therapy, which led shortly thereafter to a reconciliation. (c) 2014 APA, all rights reserved.

Impaired work performance among women with symptomatic uterine fibroids.

PubMed

Lerner, Debra; Mirza, Fadi G; Mirza, Fadi; Chang, Hong; Renzulli, Karen; Perch, Katherine; Chelmow, David

2008-10-01

To assess the work impact of symptomatic uterine fibroids (UFs). A cohort study compared 58 employed women with symptomatic UFs to 56 healthy controls. Data sources included a self-administered mail questionnaire and medical charts. At-work performance limitations and productivity loss were measured with the Work Limitations Questionnaire. Univariate and multivariate case-control group differences were tested. Based on adjusted mean scores, the UF group had significantly more at-work limitations and productivity loss than controls, while absence rates were similar. The UF group's performance was impaired 18% of the time on average versus 8% for controls (P-values, 0.005-0.040). At-work limitations were explained by depression symptoms, Non-White race/ethnicity, and poorer health-related quality of life. Fibroids and related symptoms impose a burden on the working lives' of women, their employers, and the economy.

Dynamics of Conflicts in Wikipedia

PubMed Central

Yasseri, Taha; Sumi, Robert; Rung, András; Kornai, András; Kertész, János

2012-01-01

In this work we study the dynamical features of editorial wars in Wikipedia (WP). Based on our previously established algorithm, we build up samples of controversial and peaceful articles and analyze the temporal characteristics of the activity in these samples. On short time scales, we show that there is a clear correspondence between conflict and burstiness of activity patterns, and that memory effects play an important role in controversies. On long time scales, we identify three distinct developmental patterns for the overall behavior of the articles. We are able to distinguish cases eventually leading to consensus from those cases where a compromise is far from achievable. Finally, we analyze discussion networks and conclude that edit wars are mainly fought by few editors only. PMID:22745683

Nonstationary EO/IR Clutter Suppression and Dim Object Tracking

DTIC Science & Technology

2010-01-01

Brown, A., and Brown, J., Enhanced Algorithms for EO /IR Electronic Stabilization, Clutter Suppression, and Track - Before - Detect for Multiple Low...estimation-suppression and nonlinear filtering-based multiple-object track - before - detect . These algorithms are suitable for integration into...In such cases, it is imperative to develop efficient real or near-real time tracking before detection methods. This paper continues the work started

[Development and practice evaluation of blood acid-base imbalance analysis software].

PubMed

Chen, Bo; Huang, Haiying; Zhou, Qiang; Peng, Shan; Jia, Hongyu; Ji, Tianxing

2014-11-01

To develop a blood gas, acid-base imbalance analysis computer software to diagnose systematically, rapidly, accurately and automatically determine acid-base imbalance type, and evaluate the clinical application. Using VBA programming language, a computer aided diagnostic software for the judgment of acid-base balance was developed. The clinical data of 220 patients admitted to the Second Affiliated Hospital of Guangzhou Medical University were retrospectively analyzed. The arterial blood gas [pH value, HCO(3)(-), arterial partial pressure of carbon dioxide (PaCO₂)] and electrolytes included data (Na⁺ and Cl⁻) were collected. Data were entered into the software for acid-base imbalances judgment. At the same time the data generation was calculated manually by H-H compensation formula for determining the type of acid-base imbalance. The consistency of judgment results from software and manual calculation was evaluated, and the judgment time of two methods was compared. The clinical diagnosis of the types of acid-base imbalance for the 220 patients: 65 cases were normal, 90 cases with simple type, mixed type in 41 cases, and triplex type in 24 cases. The accuracy of the judgment results of the normal and triplex types from computer software compared with which were calculated manually was 100%, the accuracy of the simple type judgment was 98.9% and 78.0% for the mixed type, and the total accuracy was 95.5%. The Kappa value of judgment result from software and manual judgment was 0.935, P=0.000. It was demonstrated that the consistency was very good. The time for software to determine acid-base imbalances was significantly shorter than the manual judgment (seconds:18.14 ± 3.80 vs. 43.79 ± 23.86, t=7.466, P=0.000), so the method of software was much faster than the manual method. Software judgment can replace manual judgment with the characteristics of rapid, accurate and convenient, can improve work efficiency and quality of clinical doctors and has great clinical application promotion value.

Anticipating cognitive effort: roles of perceived error-likelihood and time demands.

PubMed

Dunn, Timothy L; Inzlicht, Michael; Risko, Evan F

2017-11-13

Why are some actions evaluated as effortful? In the present set of experiments we address this question by examining individuals' perception of effort when faced with a trade-off between two putative cognitive costs: how much time a task takes vs. how error-prone it is. Specifically, we were interested in whether individuals anticipate engaging in a small amount of hard work (i.e., low time requirement, but high error-likelihood) vs. a large amount of easy work (i.e., high time requirement, but low error-likelihood) as being more effortful. In between-subject designs, Experiments 1 through 3 demonstrated that individuals anticipate options that are high in perceived error-likelihood (yet less time consuming) as more effortful than options that are perceived to be more time consuming (yet low in error-likelihood). Further, when asked to evaluate which of the two tasks was (a) more effortful, (b) more error-prone, and (c) more time consuming, effort-based and error-based choices closely tracked one another, but this was not the case for time-based choices. Utilizing a within-subject design, Experiment 4 demonstrated overall similar pattern of judgments as Experiments 1 through 3. However, both judgments of error-likelihood and time demand similarly predicted effort judgments. Results are discussed within the context of extant accounts of cognitive control, with considerations of how error-likelihood and time demands may independently and conjunctively factor into judgments of cognitive effort.

Mining Distance Based Outliers in Near Linear Time with Randomization and a Simple Pruning Rule

NASA Technical Reports Server (NTRS)

Bay, Stephen D.; Schwabacher, Mark

2003-01-01

Defining outliers by their distance to neighboring examples is a popular approach to finding unusual examples in a data set. Recently, much work has been conducted with the goal of finding fast algorithms for this task. We show that a simple nested loop algorithm that in the worst case is quadratic can give near linear time performance when the data is in random order and a simple pruning rule is used. We test our algorithm on real high-dimensional data sets with millions of examples and show that the near linear scaling holds over several orders of magnitude. Our average case analysis suggests that much of the efficiency is because the time to process non-outliers, which are the majority of examples, does not depend on the size of the data set.

Shotgun metabolomic approach based on mass spectrometry for hepatic mitochondria of mice under arsenic exposure.

PubMed

García-Sevillano, M A; García-Barrera, T; Navarro, F; Montero-Lobato, Z; Gómez-Ariza, J L

2015-04-01

Mass spectrometry (MS)-based toxicometabolomics requires analytical approaches for obtaining unbiased metabolic profiles. The present work explores the general application of direct infusion MS using a high mass resolution analyzer (a hybrid systems triple quadrupole-time-of-flight) and a complementary gas chromatography-MS analysis to mitochondria extracts from mouse hepatic cells, emphasizing on mitochondria isolation from hepatic cells with a commercial kit, sample treatment after cell lysis, comprehensive metabolomic analysis and pattern recognition from metabolic profiles. Finally, the metabolomic platform was successfully checked on a case-study based on the exposure experiment of mice Mus musculus to inorganic arsenic during 12 days. Endogenous metabolites alterations were recognized by partial least squares-discriminant analysis. Subsequently, metabolites were identified by combining MS/MS analysis and metabolomics databases. This work reports for the first time the effects of As-exposure on hepatic mitochondria metabolic pathways based on MS, and reveals disturbances in Krebs cycle, β-oxidation pathway, amino acids degradation and perturbations in creatine levels. This non-target analysis provides extensive metabolic information from mitochondrial organelle, which could be applied to toxicology, pharmacology and clinical studies.

Five Strategies of Successful Part-Time Work.

ERIC Educational Resources Information Center

Corwin, Vivien; Lawrence, Thomas B.; Frost, Peter J.

2001-01-01

Identifies commonalities in the approaches of successful part-time professionals. Discusses five strategies for success: (1) communicating work-life priorities and schedules to the organization; (2) making the business case for part-time arrangements; (3) establishing time management routines; (4) cultivating advocates in senior management; and…

Influence of changing work patterns on training in anaesthesia: an analysis of activity in a UK teaching hospital from 1996 to 2004.

PubMed

Underwood, S M; McIndoe, A K

2005-11-01

We aimed to assess the influence of reduced working hours on training in a UK teaching hospital as the specialist registrar grade was introduced in 1996, the New Deal was implemented in 2001 and the Working Time Directive (WTD) took effect for doctors in training in 2004. We analysed data from operating theatres in our hospital looking at grade of anaesthetist, time of day, emergency category, and specialty for more than 50,000 cases. Although direct supervision of trainees increased from 32 to 37 to 47%, senior house officer (SHO) and specialist registrar (SpR) caseload reduced by 20 and 21%, respectively, while that of the consultants rose. The reduction in total operating theatre cases for our trainees was evident across the epochs analysed, case numbers fell after introduction of the New Deal as well as more recently following the WTD, particularly for SHOs who are now doing a larger proportion of their work at night. SHOs and SpRs are doing more obstetric cases than in previous times but these are regional and not general anaesthetics.

The role of production and teamwork practices in construction safety: a cognitive model and an empirical case study.

PubMed

Mitropoulos, Panagiotis Takis; Cupido, Gerardo

2009-01-01

In construction, the challenge for researchers and practitioners is to develop work systems (production processes and teams) that can achieve high productivity and high safety at the same time. However, construction accident causation models ignore the role of work practices and teamwork. This study investigates the mechanisms by which production and teamwork practices affect the likelihood of accidents. The paper synthesizes a new model for construction safety based on the cognitive perspective (Fuller's Task-Demand-Capability Interface model, 2005) and then presents an exploratory case study. The case study investigates and compares the work practices of two residential framing crews: a 'High Reliability Crew' (HRC)--that is, a crew with exceptional productivity and safety over several years, and an average performing crew from the same company. The model explains how the production and teamwork practices generate the work situations that workers face (the task demands) and affect the workers ability to cope (capabilities). The case study indicates that the work practices of the HRC directly influence the task demands and match them with the applied capabilities. These practices were guided by the 'principle' of avoiding errors and rework and included work planning and preparation, work distribution, managing the production pressures, and quality and behavior monitoring. The Task Demand-Capability model links construction research to a cognitive model of accident causation and provides a new way to conceptualize safety as an emergent property of the production practices and teamwork processes. The empirical evidence indicates that the crews' work practices and team processes strongly affect the task demands, the applied capabilities, and the match between demands and capabilities. The proposed model and the exploratory case study will guide further discovery of work practices and teamwork processes that can increase both productivity and safety in construction operations. Such understanding will enable training of construction foremen and crews in these practices to systematically develop high reliability crews.

Case-Based Learning with Worked Examples in Complex Domains: Two Experimental Studies in Undergraduate Medical Education

ERIC Educational Resources Information Center

Stark, Robin; Kopp, Veronika; Fischer, Martin R.

2011-01-01

To investigate the effects of example format (erroneous examples vs. correct examples) and feedback format (elaborated feedback vs. knowledge of results feedback) on medical students' diagnostic competence in the context of a web-based learning environment containing case-based worked examples, two studies with a 2 x 2 design were conducted in the…

An advanced approach to traditional round robin CPU scheduling algorithm to prioritize processes with residual burst time nearest to the specified time quantum

NASA Astrophysics Data System (ADS)

Swaraj Pati, Mythili N.; Korde, Pranav; Dey, Pallav

2017-11-01

The purpose of this paper is to introduce an optimised variant to the round robin scheduling algorithm. Every algorithm works in its own way and has its own merits and demerits. The proposed algorithm overcomes the shortfalls of the existing scheduling algorithms in terms of waiting time, turnaround time, throughput and number of context switches. The algorithm is pre-emptive and works based on the priority of the associated processes. The priority is decided on the basis of the remaining burst time of a particular process, that is; lower the burst time, higher the priority and higher the burst time, lower the priority. To complete the execution, a time quantum is initially specified. In case if the burst time of a particular process is less than 2X of the specified time quantum but more than 1X of the specified time quantum; the process is given high priority and is allowed to execute until it completes entirely and finishes. Such processes do not have to wait for their next burst cycle.

Defining Tsunami Magnitude as Measure of Potential Impact

NASA Astrophysics Data System (ADS)

Titov, V. V.; Tang, L.

2016-12-01

The goal of tsunami forecast, as a system for predicting potential impact of a tsunami at coastlines, requires quick estimate of a tsunami magnitude. This goal has been recognized since the beginning of tsunami research. The work of Kajiura, Soloviev, Abe, Murty, and many others discussed several scales for tsunami magnitude based on estimates of tsunami energy. However, difficulties of estimating tsunami energy based on available tsunami measurements at coastal sea-level stations has carried significant uncertainties and has been virtually impossible in real time, before tsunami impacts coastlines. The slow process of tsunami magnitude estimates, including collection of vast amount of available coastal sea-level data from affected coastlines, made it impractical to use any tsunami magnitude scales in tsunami warning operations. Uncertainties of estimates made tsunami magnitudes difficult to use as universal scale for tsunami analysis. Historically, the earthquake magnitude has been used as a proxy of tsunami impact estimates, since real-time seismic data is available of real-time processing and ample amount of seismic data is available for an elaborate post event analysis. This measure of tsunami impact carries significant uncertainties in quantitative tsunami impact estimates, since the relation between the earthquake and generated tsunami energy varies from case to case. In this work, we argue that current tsunami measurement capabilities and real-time modeling tools allow for establishing robust tsunami magnitude that will be useful for tsunami warning as a quick estimate for tsunami impact and for post-event analysis as a universal scale for tsunamis inter-comparison. We present a method for estimating the tsunami magnitude based on tsunami energy and present application of the magnitude analysis for several historical events for inter-comparison with existing methods.

Trajectory Planning by Preserving Flexibility: Metrics and Analysis

NASA Technical Reports Server (NTRS)

Idris, Husni R.; El-Wakil, Tarek; Wing, David J.

2008-01-01

In order to support traffic management functions, such as mitigating traffic complexity, ground and airborne systems may benefit from preserving or optimizing trajectory flexibility. To help support this hypothesis trajectory flexibility metrics have been defined in previous work to represent the trajectory robustness and adaptability to the risk of violating safety and traffic management constraints. In this paper these metrics are instantiated in the case of planning a trajectory with the heading degree of freedom. A metric estimation method is presented based on simplifying assumptions, namely discrete time and heading maneuvers. A case is analyzed to demonstrate the estimation method and its use in trajectory planning in a situation involving meeting a time constraint and avoiding loss of separation with nearby traffic. The case involves comparing path-stretch trajectories, in terms of adaptability and robustness along each, deduced from a map of estimated flexibility metrics over the solution space. The case demonstrated anecdotally that preserving flexibility may result in enhancing certain factors that contribute to traffic complexity, namely reducing proximity and confrontation.

An experimental study on the effects of a simulation game on students' clinical cognitive skills and motivation.

PubMed

Dankbaar, Mary E W; Alsma, Jelmer; Jansen, Els E H; van Merrienboer, Jeroen J G; van Saase, Jan L C M; Schuit, Stephanie C E

2016-08-01

Simulation games are becoming increasingly popular in education, but more insight in their critical design features is needed. This study investigated the effects of fidelity of open patient cases in adjunct to an instructional e-module on students' cognitive skills and motivation. We set up a three-group randomized post-test-only design: a control group working on an e-module; a cases group, combining the e-module with low-fidelity text-based patient cases, and a game group, combining the e-module with a high-fidelity simulation game with the same cases. Participants completed questionnaires on cognitive load and motivation. After a 4-week study period, blinded assessors rated students' cognitive emergency care skills in two mannequin-based scenarios. In total 61 students participated and were assessed; 16 control group students, 20 cases students and 25 game students. Learning time was 2 h longer for the cases and game groups than for the control group. Acquired cognitive skills did not differ between groups. The game group experienced higher intrinsic and germane cognitive load than the cases group (p = 0.03 and 0.01) and felt more engaged (p < 0.001). Students did not profit from working on open cases (in adjunct to an e-module), which nonetheless challenged them to study longer. The e-module appeared to be very effective, while the high-fidelity game, although engaging, probably distracted students and impeded learning. Medical educators designing motivating and effective skills training for novices should align case complexity and fidelity with students' proficiency level. The relation between case-fidelity, motivation and skills development is an important field for further study.

In search of a representative sample of residential building work.

PubMed

Lobb, Brenda; Woods, Gregory R

2012-09-01

Most research investigating injuries in construction work is limited by reliance on work samples unrepresentative of the multiple, variable-cycle tasks involved, resulting in incomplete characterisation of ergonomic exposures. In this case study, a participatory approach was used including hierarchical task analysis and site observations of a typical team of house builders in New Zealand, over several working days, to obtain a representative work sample. The builders' work consisted of 14 goal-defined jobs using varying subsets of 15 task types, each taking from less than 1 s to more than 1 h and performed in a variety of postures. Task type and duration varied within and between participants and days, although all participants spent at least 25% of the time moving from place to place, mostly carrying materials, and more than half the time either reaching up or bending down to work. This research has provided a description of residential building work based on a work sample more nearly representative than those previously published and has demonstrated a simple, low-cost but robust field observation method that can provide a valid basis for further study of hazard exposures. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Fibromyalgia: epidemiology and risk factors, a population-based case-control study in Lebanon.

PubMed

Moukaddem, Afaf; Chaaya, Monique; Slim, Zeinab F N; Jaffa, Miran; Sibai, Abla Mehio; Uthman, Imad

2017-02-01

To investigate the epidemiology of fibromyalgia (FM) and assess its risk factors. Using data from the 2009 Community Oriented Program for Control of Rheumatic Diseases (COPCORD) study conducted in Lebanon, a population-based case control study was performed. The sample included 34 FM patients, frequency matched with 136 controls free from any musculoskeletal complaints and randomly sampled from the population. The controls were frequency matched with cases by age and gender. The 34 female FM cases were prevalent cases which existed for a long period of time and all those who consulted a doctor were previously misdiagnosed. Family history of joint problems (OR = 4.93, 95% CI: 1.56-15.58) and working status (OR = 2.69, 95% CI: 1.04-6.93) were significant risk factors for FM, after adjusting for body mass index, distress level, smoking status and residence location. This was the first study to address the epidemiology of FM in Lebanon and the region. The chronic nature of FM that is characterized by frequent bouts of intense disabling pain and symptoms constitutes a significant health and economic burden. Clustering of cases in coastal areas was partially explained by other factors such as body mass index, distress level, smoking and work status. The high burden of FM found in our study calls for further investigation of potential risk factors of this condition. © 2015 Asia Pacific League of Associations for Rheumatology and Wiley Publishing Asia Pty Ltd.

Lung cancer among coal miners, ore miners and quarrymen: smoking-adjusted risk estimates from the synergy pooled analysis of case-control studies.

PubMed

Taeger, Dirk; Pesch, Beate; Kendzia, Benjamin; Behrens, Thomas; Jöckel, Karl-Heinz; Dahmann, Dirk; Siemiatycki, Jack; Kromhout, Hans; Vermeulen, Roel; Peters, Susan; Olsson, Ann; Brüske, Irene; Wichmann, Heinz-Erich; Stücker, Isabelle; Guida, Florence; Tardón, Adonina; Merletti, Franco; Mirabelli, Dario; Richiardi, Lorenzo; Pohlabeln, Hermann; Ahrens, Wolfgang; Landi, Maria Teresa; Caporaso, Neil; Pesatori, Angela Cecilia; Mukeriya, Anush; Szeszenia-Dabrowska, Neonila; Lissowska, Jolanta; Gustavsson, Per; Field, John; Marcus, Michael W; Fabianova, Eleonora; 't Mannetje, Andrea; Pearce, Neil; Rudnai, Peter; Bencko, Vladimir; Janout, Vladimir; Dumitru, Rodica Stanescu; Foretova, Lenka; Forastiere, Francesco; McLaughlin, John; Paul Demers, Paul Demers; Bueno-de-Mesquita, Bas; Schüz, Joachim; Straif, Kurt; Brüning, Thomas

2015-09-01

Working in mines and quarries has been associated with an elevated lung cancer risk but with inconsistent results for coal miners. This study aimed to estimate the smoking-adjusted lung cancer risk among coal miners and compare the risk pattern with lung cancer risks among ore miners and quarrymen. We estimated lung cancer risks of coal and ore miners and quarrymen among 14 251 lung cancer cases and 17 267 controls from the SYNERGY pooled case-control study, controlling for smoking and employment in other at-risk occupations. Ever working as miner or quarryman (690 cases, 436 controls) was associated with an elevated odds ratio (OR) of 1.55 [95% confidence interval (95% CI) 1.34-1.79] for lung cancer. Ore miners (53 cases, 24 controls) had a higher OR (2.34, 95% CI 1.36-4.03) than quarrymen (67 cases, 39 controls; OR 1.92, 95% CI 1.21-3.05) and coal miners (442 cases, 297 controls; OR 1.40, 95% CI 1.18-1.67), but CI overlapped. We did not observe trends by duration of exposure or time since last exposure. This pooled analysis of population-based studies demonstrated an excess lung cancer risk among miners and quarrymen that remained increased after adjustment for detailed smoking history and working in other at-risk occupations. The increase in risk among coal miners were less pronounced than for ore miners or quarrymen.

Breaking the Long Hours Culture.

ERIC Educational Resources Information Center

Kodz, J.; Kersley, B.; Strebler, M. T.; O'Regan, S.

Case studies of 12 leading British employers were driven by employers' interest in issues related to working long hours in light of introduction of the Working Time Directive, a European Community initiative enacted into British law that sets limits on working hours per week. Data showed over one-fourth of full-time employees worked over 48 hours…

The utilization of tachymetry in forensic medicine.

PubMed

Hagara, M; Sidlo, J; Stuparin, J; Siget, V; Soral, A; Valent, D

2009-01-01

Tachymetry is a geodetic method enabling to measure angles and distances. The aim of the work was to demonstrate alternatives of its utilization in daily forensic medicine practice. The work is dealing with confusing cases of gunshot injuries. It is impossible to determine the trajectory of the projectile, the sequence of gunshots, to identify shooting person etc. in these cases only on the base of autopsy findings and investigated circumstances. In these cases the investigation experiments on the crime scene in collaboration with the land surveyors were realized. The work presents two case reports. For our measurements the electronic tachymeter TOPCON 211D was used. These were performed by the means of polar method in local coordinate system with relative heights. In the first case the position of victim was simulated by a figurant according to testimonies of witnesses and the accused. The second case dealed with suicide. In the first case there were two gunshots. The trajectory of the first gunshot was determined and the projectile was found. Hereby the most authentic testimony could be estimated. Also high grade probability of the relative position of the victim and the accused was figured out. In the case of suicide also the projectile was found and the position of the victim in the time of gunshot was determined. In the both case reports demonstrated the projectiles were not found by ballistics expert investigations. All questions of expert opinions could be answered only with the help of tachymetry. The advantage of this method is its good regional availability even at places far from specialized criminal investigation workplaces.

A Case-Based Study with Radiologists Performing Diagnosis Tasks in Virtual Reality.

PubMed

Venson, José Eduardo; Albiero Berni, Jean Carlo; Edmilson da Silva Maia, Carlos; Marques da Silva, Ana Maria; Cordeiro d'Ornellas, Marcos; Maciel, Anderson

2017-01-01

In radiology diagnosis, medical images are most often visualized slice by slice. At the same time, the visualization based on 3D volumetric rendering of the data is considered useful and has increased its field of application. In this work, we present a case-based study with 16 medical specialists to assess the diagnostic effectiveness of a Virtual Reality interface in fracture identification over 3D volumetric reconstructions. We developed a VR volume viewer compatible with both the Oculus Rift and handheld-based head mounted displays (HMDs). We then performed user experiments to validate the approach in a diagnosis environment. In addition, we assessed the subjects' perception of the 3D reconstruction quality, ease of interaction and ergonomics, and also the users opinion on how VR applications can be useful in healthcare. Among other results, we have found a high level of effectiveness of the VR interface in identifying superficial fractures on head CTs.

Professional relationships and power dynamics between urban community-based nurses and social work case managers: advocacy in action.

PubMed

Young, Staci

2009-01-01

The purpose of this study was to explore how community-based case managers interface with their clients' healthcare providers and other community organizations as a function within their advocacy efforts. Case managers previously defined advocacy as occurring at individual, organizational, and community levels. The relationships they attempt to develop and maintain are consistent with case management ideology, yet this is a complex process to ensure care for vulnerable populations with many medical and socioeconomic needs. Community-based case management settings. In-depth qualitative interviews with a total of 20 nurse and social work case managers working in public housing, university-affiliated community nursing centers, local parishes, and community ministry. The case managers in this study reflected on how they interface with their clients, other healthcare providers, and community organizations on behalf of their clients. They reflect on the importance of trust and communication to facilitate this process. The advocacy work of case managers is influenced by the setting, others' perceptions of their knowledge and expertise, and power dynamics. Their ability to effectively advocate is greatly influenced by the strength of the relationships they forge. Advocacy for vulnerable clients is influenced by the existing relationship between case managers and their clients' healthcare providers. Case managers need to be persistent in their interactions with other providers to ensure that their clients have access to valuable community resources. Clear lines of communication should be established between case managers so that there is clarity around roles and expectations in service provision. Case managers should also participate in the mentoring of future health professions students so they may learn the application of advocacy work in community settings.

Time-based management of patient processes.

PubMed

Kujala, Jaakko; Lillrank, Paul; Kronström, Virpi; Peltokorpi, Antti

2006-01-01

The purpose of this paper is to present a conceptual framework that would enable the effective application of time based competition (TBC) and work in process (WIP) concepts in the design and management of effective and efficient patient processes. This paper discusses the applicability of time-based competition and work-in-progress concepts to the design and management of healthcare service production processes. A conceptual framework is derived from the analysis of both existing research and empirical case studies. The paper finds that a patient episode is analogous to a customer order-to-delivery chain in industry. The effective application of TBC and WIP can be achieved by focusing on through put time of a patient episode by reducing the non-value adding time components and by minimizing time categories that are main cost drivers for all stakeholders involved in the patient episode. The paper shows that an application of TBC in managing patient processes can be limited if there is no consensus about optimal care episode in the medical community. In the paper it is shown that managing patient processes based on time and cost analysis enables one to allocate the optimal amount of resources, which would allow a healthcare system to minimize the total cost of specific episodes of illness. Analysing the total cost of patient episodes can provide useful information in the allocation of limited resources among multiple patient processes. This paper introduces a framework for health care managers and researchers to analyze the effect of reducing through put time to the total cost of patient episodes.

Application of State Quantization-Based Methods in HEP Particle Transport Simulation

NASA Astrophysics Data System (ADS)

Santi, Lucio; Ponieman, Nicolás; Jun, Soon Yung; Genser, Krzysztof; Elvira, Daniel; Castro, Rodrigo

2017-10-01

Simulation of particle-matter interactions in complex geometries is one of the main tasks in high energy physics (HEP) research. An essential aspect of it is an accurate and efficient particle transportation in a non-uniform magnetic field, which includes the handling of volume crossings within a predefined 3D geometry. Quantized State Systems (QSS) is a family of numerical methods that provides attractive features for particle transportation processes, such as dense output (sequences of polynomial segments changing only according to accuracy-driven discrete events) and lightweight detection and handling of volume crossings (based on simple root-finding of polynomial functions). In this work we present a proof-of-concept performance comparison between a QSS-based standalone numerical solver and an application based on the Geant4 simulation toolkit, with its default Runge-Kutta based adaptive step method. In a case study with a charged particle circulating in a vacuum (with interactions with matter turned off), in a uniform magnetic field, and crossing up to 200 volume boundaries twice per turn, simulation results showed speedups of up to 6 times in favor of QSS while it being 10 times slower in the case with zero volume boundaries.

Historical Trends of Participation of Women Scientists in Robotic Spacecraft Mission Science Teams: Effect of Participating Scientist Programs

NASA Astrophysics Data System (ADS)

Rathbun, Julie A.; Castillo-Rogez, Julie; Diniega, Serina; Hurley, Dana; New, Michael; Pappalardo, Robert T.; Prockter, Louise; Sayanagi, Kunio M.; Schug, Joanna; Turtle, Elizabeth P.; Vasavada, Ashwin R.

2016-10-01

Many planetary scientists consider involvement in a robotic spacecraft mission the highlight of their career. We have searched for names of science team members and determined the percentage of women on each team. We have limited the lists to members working at US institutions at the time of selection. We also determined the year each team was selected. The gender of each team member was limited to male and female and based on gender expression. In some cases one of the authors knew the team member and what pronouns they use. In other cases, we based our determinations on the team member's name or photo (obtained via a google search, including institution). Our initial analysis considered 22 NASA planetary science missions over a period of 41 years and only considered NASA-selected PI and Co-Is and not participating scientists, postdocs, or graduate students. We found that there has been a dramatic increase in participation of women on spacecraft science teams since 1974, from 0-2% in the 1970s - 1980s to an average of 14% 2000-present. This, however, is still lower than the recent percentage of women in planetary science, which 3 different surveys found to be ~25%. Here we will present our latest results, which include consideration of participating scientists. As in the case of PIs and Co-Is, we consider only participating scientists working at US institutions at the time of their selection.

Employer Involvement in Work-Based Learning Programs.

ERIC Educational Resources Information Center

Bailey, Thomas; Hughes, Katherine

A 3-year research project focused on whether sufficient numbers of employers could be recruited to create a national school-to-work system with a substantial work-based learning component as called for by the 1994 School-to-Work Opportunities Act. Research methods were as follows: case studies of 12 work-based learning programs at 9 sites located…

Judicial case management and the custody and access assessment: melding the approaches.

PubMed

Leverette, J; Crowe, T; Wenglensky, R; Dunbar, M

1997-08-01

The presence of the Unified Family Court, with procedures emphasizing judicial case management and settlement in custody disputes, provided an opportunity to combine these practices with those of a university hospital-based family court clinic experienced in the provision of custody assessments. Specifically, a process integrating the clinical custody assessment with the work of counsel and court procedures was developed. This format, incorporating the preparation of a clinical settlement conference brief, was then evaluated with emphasis on time management, outcome in relation to settlement or trial, and the effect of clinical assessment at critical points in the combined endeavour. Seventy-two judicial referrals conducted using this format were reviewed. To assess efficiency, we determined time intervals to various points in the process and compared them to previous local practice. Settlement rates, recorded incrementally to mark each component's contribution, were compared with rates noted in the literature. Assessment functions were identified according to the point of resolution of the dispute and in a manner to facilitate comparison with previously published work. The format resulted in 50% of cases settling without trial in under 5 months, a minimum settlement rate of 50%, and confirmed the ability of clinical assessment to contribute flexibly to dispute resolution in several conciliation venues and at trial. Combining legal and mental health efforts can results in more efficient use of resources and a substantial diversion of cases from continuing litigation. While altering the process of clinical assessments enhances such findings, further work is required to assure appropriate selection criteria for various intervention formats.

RDBMS Applications as Online Based Data Archive: A Case of Harbour Medical Center in Pekanbaru

NASA Astrophysics Data System (ADS)

Febriadi, Bayu; Zamsuri, Ahmad

2017-12-01

Kantor Kesehatan Pelabuhan Kelas II Pekanbaru is a government office that concerns about healthy, especially about environment health. There is a problem in case of saving electronic data, also in analyzing daily data both for internal and external data. The office has some computers and other tools that are useful in saving electronic data. In fact, the data are still saved in available cupboards and it is not efficient for an important data that is analyzed for more than one time. In other words, it is not good for a data is needed to be analyzed continuously. Rational Data Base Management System (RDBMS) application is an online based saving data and it uses System Development Life Cycle (SDLC) method. Hopefully, the application will be very useful for employees Kantor Kesehatan Pelabuhan Pekanbaru in managing their work.

A study of work injuries in eight Asian countries.

PubMed

Ong, C N; Phoon, W O; Tan, T C; Jeyaratnam, J; Cho, S C; Suma'mur, P K; Mahathevan, R; Reverente, B R; Wongphanich, W; Kogi, K

1984-04-01

This study is based on a survey conducted in Hong Kong, Indonesia, Korea, Malaysia, the Philippines, Singapore, Sri Lanka and Thailand on occupational injuries during the years 1975-1980. The number of work accidents have risen rapidly during this period in all of the 8 countries studied. In the case of Thailand, the total number of work injuries increased four fold from 1975-1978, whereas, in Singapore it has almost doubled in 6 years. The number of permanent disablement nearly trebled in Korea, and the Philippines for the year 1967-1980. The largest percentage of accidents are lost-time injuries in all of the 8 countries. Thailand had a three fold increase in lost-time injuries whilst in Hong Kong the figure doubled. Six out of the 8 countries indicated that the building construction industry had the largest number of fatal accidents, followed by the manufacturing industry.

Case formulation in clinical practice: Associations with psychological mindedness, attachment and burnout in staff working with people experiencing psychosis.

PubMed

Hartley, Samantha; Jovanoska, Jelena; Roberts, Susan; Burden, Nicolas; Berry, Katherine

2016-06-01

Case formulation can impact on therapeutic relationships, staff understanding and outcomes, which might be particularly important when working with complex mental health problems such as psychosis. However, the evidence base is equivocal and there is insufficient understanding around the staff-related factors that influence effective psychological case formulation. This study investigated the influence of staff characteristics (both professional and personal) on case formulation skill. This was a cross-sectional study, with all of the measures collected at the same time point. Fifty staff members working on inpatient wards with individuals experiencing psychosis were recruited. Measures included independently rated case formulation skill and psychological mindedness (the ability to draw together aspects of thoughts, feelings and actions), both in relation to hypothetical cases. Self-report questionnaires assessed psychological mindedness, attachment styles, symptoms of burnout and professional qualifications. The preliminary analyses indicated that case formulation skill was associated with higher psychological mindedness (both self-reported and independently-rated) and lower levels of avoidant attachment styles. Simultaneous entry multiple regression demonstrated that the only independent predictor of case formulation skill was independently rated psychological mindedness. These findings highlight the factors that contribute to staff's ability to case formulate and the possibility for services to develop psychological mindedness and case formulation skills through formal training, alongside fostering a psychological minded working environment. Case formulation skill is positively associated with the personal ability (or inclination) to draw together aspects of experience in a psychological manner (i.e., psychological mindedness) It might also be important to consider avoidant attachment tendencies in relation to formulation skills The sample was relatively small and drawn from a limited number of services, which might reduce the generalizability of the findings Psychological mindedness might not be captured adequately by self-report tools and services may wish to employ more novel ways of assessing this important skill in staff groups (such as the speech sample used in the current study). © 2015 The British Psychological Society.

A Step-by-Step Design Methodology for a Base Case Vanadium Redox-Flow Battery

ERIC Educational Resources Information Center

Moore, Mark; Counce, Robert M.; Watson, Jack S.; Zawodzinski, Thomas A.; Kamath, Haresh

2012-01-01

The purpose of this work is to develop an evolutionary procedure to be used by Chemical Engineering students for the base-case design of a Vanadium Redox-Flow Battery. The design methodology is based on the work of Douglas (1985) and provides a profitability analysis at each decision level so that more profitable alternatives and directions can be…

Many-Particle Dephasing after a Quench

NASA Astrophysics Data System (ADS)

Kiendl, Thomas; Marquardt, Florian

2017-03-01

After a quench in a quantum many-body system, expectation values tend to relax towards long-time averages. However, temporal fluctuations remain in the long-time limit, and it is crucial to study the suppression of these fluctuations with increasing system size. The particularly important case of nonintegrable models has been addressed so far only by numerics and conjectures based on analytical bounds. In this work, we are able to derive analytical predictions for the temporal fluctuations in a nonintegrable model (the transverse Ising chain with extra terms). Our results are based on identifying a dynamical regime of "many-particle dephasing," where quasiparticles do not yet relax but fluctuations are nonetheless suppressed exponentially by weak integrability breaking.

Many-Particle Dephasing after a Quench.

PubMed

Kiendl, Thomas; Marquardt, Florian

2017-03-31

After a quench in a quantum many-body system, expectation values tend to relax towards long-time averages. However, temporal fluctuations remain in the long-time limit, and it is crucial to study the suppression of these fluctuations with increasing system size. The particularly important case of nonintegrable models has been addressed so far only by numerics and conjectures based on analytical bounds. In this work, we are able to derive analytical predictions for the temporal fluctuations in a nonintegrable model (the transverse Ising chain with extra terms). Our results are based on identifying a dynamical regime of "many-particle dephasing," where quasiparticles do not yet relax but fluctuations are nonetheless suppressed exponentially by weak integrability breaking.

Augment clinical measurement using a constraint-based esophageal model

NASA Astrophysics Data System (ADS)

Kou, Wenjun; Acharya, Shashank; Kahrilas, Peter; Patankar, Neelesh; Pandolfino, John

2017-11-01

Quantifying the mechanical properties of the esophageal wall is crucial to understanding impairments of trans-esophageal flow characteristic of several esophageal diseases. However, these data are unavailable owing to technological limitations of current clinical diagnostic instruments that instead display esophageal luminal cross sectional area based on intraluminal impedance change. In this work, we developed an esophageal model to predict bolus flow and the wall property based on clinical measurements. The model used the constraint-based immersed-boundary method developed previously by our group. Specifically, we first approximate the time-dependent wall geometry based on impedance planimetry data on luminal cross sectional area. We then fed these along with pressure data into the model and computed wall tension based on simulated pressure and flow fields, and the material property based on the strain-stress relationship. As examples, we applied this model to augment FLIP (Functional Luminal Imaging Probe) measurements in three clinical cases: a normal subject, achalasia, and eosinophilic esophagitis (EoE). Our findings suggest that the wall stiffness was greatest in the EoE case, followed by the achalasia case, and then the normal. This is supported by NIH Grant R01 DK56033 and R01 DK079902.

Participation in Science Practices while Working in a Multimedia Case-Based Environment

ERIC Educational Resources Information Center

Kang, Hosun; Lundeberg, Mary A.

2010-01-01

The purpose of this study was to investigate how two female students participated in science practices as they worked in a multimedia case-based environment: interpreting simulated results, reading and writing multiple texts, role-playing, and Internet conferencing. Using discourse analysis, the following data were analyzed: students' published…

Problem-Based Learning in Online Environments

ERIC Educational Resources Information Center

An, Yun-Jo; Reigeluth, Charles M.

2008-01-01

This study examined 3 graduate-level online courses that utilized problem-based learning (PBL), considering each course as a case. Beyond describing how PBL was implemented in each case, this study identified what worked (strengths) and did not work (weaknesses) in the PBL and explored how the PBL could be improved (improvements) by collecting…

Symmetric and antisymmetric forms of the Pauli master equation.

PubMed

Klimenko, A Y

2016-07-21

When applied to matter and antimatter states, the Pauli master equation (PME) may have two forms: time-symmetric, which is conventional, and time-antisymmetric, which is suggested in the present work. The symmetric and antisymmetric forms correspond to symmetric and antisymmetric extensions of thermodynamics from matter to antimatter - this is demonstrated by proving the corresponding H-theorem. The two forms are based on the thermodynamic similarity of matter and antimatter and differ only in the directions of thermodynamic time for matter and antimatter (the same in the time-symmetric case and the opposite in the time-antisymmetric case). We demonstrate that, while the symmetric form of PME predicts an equibalance between matter and antimatter, the antisymmetric form of PME favours full conversion of antimatter into matter. At this stage, it is impossible to make an experimentally justified choice in favour of the symmetric or antisymmetric versions of thermodynamics since we have no experience of thermodynamic properties of macroscopic objects made of antimatter, but experiments of this kind may become possible in the future.

Integrating family work into the treatment of young people with severe and complex depression: a developmentally focused model.

PubMed

Rice, Simon; Halperin, Stephen; Blaikie, Simon; Monson, Katherine; Stefaniak, Rachel; Phelan, Mark; Davey, Christopher

2018-04-01

Although models of family intervention are clearly articulated in the child and early adolescent literature, there is less clarity regarding family intervention approaches in later adolescence and emerging adulthood. This study provides the rationale and intervention framework for a developmentally sensitive model of time-limited family work in the outpatient treatment of complex youth depression (15-25 years). Derived from current practice in the Youth Mood Clinic (YMC) at Orygen Youth Health, Melbourne, a stepped model of family intervention is discussed. YMC aims to provide comprehensive orientation, assessment and education to all families. For some, a family-based intervention, delivered either by the treating team or through the integration of a specialist family worker, offers an important adjunct in supporting the recovery of the young person. Developmental phases and challenges experienced by the young person with respect to family/caregiver involvement are discussed in the context of two case studies. A developmentally sensitive model is presented with particular attention to the developmental needs and preferences of young people. Formal evaluation of this model is required. Evaluation perspectives should include young people, caregivers, the broader family system (i.e. siblings) and the treating team (i.e. case manager, doctor and family worker) incorporating outcome measurement. Such work determines how best to apply a time-limited family-based intervention approach in strengthening family/caregiver relationships as part of the young person's recovery from severe and complex depression. © 2016 John Wiley & Sons Australia, Ltd.

Finding a Balance: Fifteen Institutional Case Studies on the Relationship between Part-Time Work and Advanced Level Study. Report.

ERIC Educational Resources Information Center

Hodgson, Ann, Ed.; Spours, Ken, Ed.

This document presents and discusses case studies that examined the relationship between part-time employment and advanced level study at 15 schools in Essex, England. "Foreword" (David Jones) provides a brief overview of the project. "Finding a Balance--Fifteen Institutional Case Studies on the Relationship between Part-time Work…

Comparison of 1997 Medicare relative value units for gender-specific procedures: is Adam still worth more than Eve?

PubMed

Goff, B A; Muntz, H G; Cain, J M

1997-08-01

On January 1, 1992, Congress implemented a Medicare payment system based on relative value units (RVUs). The total RVU (which is made up of work, practice, and malpractice RVUs) is multiplied by a dollar conversion factor to set the reimbursement for all procedures covered by Medicare. In a previous study, we found that significant gender bias exists in Medicare reimbursement for female-specific services. Recently, HCFA approved increases (beginning January 1997) in the work RVU for many gynecologic procedures. This study was undertaken to compare work and total RVUs for gender-specific procedures effective January 1, 1997. Using the May 1996 Federal Register, we compared work and total RVUs for 24 pairs of gender-specific procedures. The groups were matched so that the amount of work and level of difficulty would be similar, if not identical. We validated our selection of procedures for comparison by also evaluating the average time required to perform these procedures. Comparison of work RVUs for the 24 paired procedures revealed that in 19 cases (80%), male-specific procedures had a higher RVU; in 3 cases (12%), female-specific procedures were higher; and in 2 cases, there was no difference. On average, work RVUs were 49% higher for urologic procedures than for gynecologic procedures. Comparison of total RVUs revealed that in 20 cases (83%), urologic procedures had a higher total RVU and in 3 cases (12%), gynecologic procedures were higher. On average, male-specific surgeries are reimbursed at an amount which is 37% higher than that for female-specific surgeries. Recent increases in work RVUs for many gynecologic procedures have resulted in improved reimbursement. However, even with these improvements, significant gender bias still exists in the Medicare reimbursement of female-specific procedures. This gender bias is further magnified as more private insurance carriers use the system to set reimbursement.

40 CFR Appendix B to Subpart E of... - Federal Guidelines-User Charges for Operation and Maintenance of Publicly Owned Treatment Works

Code of Federal Regulations, 2014 CFR

2014-07-01

... characteristics; i.e., levels of biochemical oxygen demand, suspended solids, etc. Each class is then assigned its... all users per unit of time. Bc = O&M cost for treatment of a unit of biochemical oxygen demand (BOD... only in cases where the water charge is based on a constant cost per unit of consumption. [39 FR 5270...

40 CFR Appendix B to Subpart E of... - Federal Guidelines-User Charges for Operation and Maintenance of Publicly Owned Treatment Works

Code of Federal Regulations, 2012 CFR

2012-07-01

... characteristics; i.e., levels of biochemical oxygen demand, suspended solids, etc. Each class is then assigned its... all users per unit of time. Bc = O&M cost for treatment of a unit of biochemical oxygen demand (BOD... only in cases where the water charge is based on a constant cost per unit of consumption. [39 FR 5270...

40 CFR Appendix B to Subpart E of... - Federal Guidelines-User Charges for Operation and Maintenance of Publicly Owned Treatment Works

Code of Federal Regulations, 2013 CFR

2013-07-01

... characteristics; i.e., levels of biochemical oxygen demand, suspended solids, etc. Each class is then assigned its... all users per unit of time. Bc = O&M cost for treatment of a unit of biochemical oxygen demand (BOD... only in cases where the water charge is based on a constant cost per unit of consumption. [39 FR 5270...

Integral equation methods for computing likelihoods and their derivatives in the stochastic integrate-and-fire model.

PubMed

Paninski, Liam; Haith, Adrian; Szirtes, Gabor

2008-02-01

We recently introduced likelihood-based methods for fitting stochastic integrate-and-fire models to spike train data. The key component of this method involves the likelihood that the model will emit a spike at a given time t. Computing this likelihood is equivalent to computing a Markov first passage time density (the probability that the model voltage crosses threshold for the first time at time t). Here we detail an improved method for computing this likelihood, based on solving a certain integral equation. This integral equation method has several advantages over the techniques discussed in our previous work: in particular, the new method has fewer free parameters and is easily differentiable (for gradient computations). The new method is also easily adaptable for the case in which the model conductance, not just the input current, is time-varying. Finally, we describe how to incorporate large deviations approximations to very small likelihoods.

Trust-Guided Behavior Adaptation Using Case-Based Reasoning

DTIC Science & Technology

2015-08-01

the same behaviors were evaluated in each set. To account for this, the similarity function looks at the overlap between the two sets and ignores...interruptions would reduce the cost of case genera- tion. 6 Related Work Existing approaches for measuring inverse trust differ from our own in that...where a case- based reasoning system considers the reliability of a case’s source, also takes trust into account . Our work also has sim- ilarities

Exploring Student Preconceptions of Readiness for Remote-Online Case-Based Learning: A Case Study

PubMed Central

2016-01-01

Background Case-based learning (CBL) is an educational approach where students work in small, collaborative groups to solve problems. Web-conferencing software provides a platform to present information and share concepts that are vital to CBL. Previous studies have found that participants were resistant to change associated with implementing e-learning; however, strategies to reduce this resistance have not been explored. Objective This study was designed to explore student preconceptions and understanding of remote-online case-based learning (RO-CBL). Methods The study took place during the Bachelor of Physiotherapy program at Monash University, Victoria, Australia, in 2013. The entire third-year cohort (n=73) was invited to participate. The primary outcome of interest was students’ preconceptions of RO-CBL, collected via pre- and posttraining surveys. Results Of the 73 students, 66 completed both surveys (attrition rate 9.6%). Three key themes relevant to student preconceptions of RO-CBL emerged: flexibility in time and location of CBL, readiness or hesitation to change to a Web-based format, and the value of training in RO-CBL that included a demonstration and trial run. Thirty-four percent of the participants were hesitant to move to an online format. Conclusions This study explored students’ preconceptions of Web-based learning and evaluated the change in students’ attitudes after training. The results suggest that educational designers should not assume that students are confident and competent in applying these technologies to professional educational activities. By identifying students’ needs before implementation, training sessions can be designed to target these needs, and improve the understanding of RO-CBL and how it works in practice. This may reduce resistance to change, enhance students’ satisfaction, and ultimately improve the learning experience. PMID:27731854

Exploring Student Preconceptions of Readiness for Remote-Online Case-Based Learning: A Case Study.

PubMed

Nicklen, Peter; Keating, Jennifer L; Maloney, Stephen

2016-04-28

Case-based learning (CBL) is an educational approach where students work in small, collaborative groups to solve problems. Web-conferencing software provides a platform to present information and share concepts that are vital to CBL. Previous studies have found that participants were resistant to change associated with implementing e-learning; however, strategies to reduce this resistance have not been explored. This study was designed to explore student preconceptions and understanding of remote-online case-based learning (RO-CBL). The study took place during the Bachelor of Physiotherapy program at Monash University, Victoria, Australia, in 2013. The entire third-year cohort (n=73) was invited to participate. The primary outcome of interest was students' preconceptions of RO-CBL, collected via pre- and posttraining surveys. Of the 73 students, 66 completed both surveys (attrition rate 9.6%). Three key themes relevant to student preconceptions of RO-CBL emerged: flexibility in time and location of CBL, readiness or hesitation to change to a Web-based format, and the value of training in RO-CBL that included a demonstration and trial run. Thirty-four percent of the participants were hesitant to move to an online format. This study explored students' preconceptions of Web-based learning and evaluated the change in students' attitudes after training. The results suggest that educational designers should not assume that students are confident and competent in applying these technologies to professional educational activities. By identifying students' needs before implementation, training sessions can be designed to target these needs, and improve the understanding of RO-CBL and how it works in practice. This may reduce resistance to change, enhance students' satisfaction, and ultimately improve the learning experience.

Internal and external resorption in a lower molar with an associated endodontic-periodontic lesion: a case report.

PubMed

Komabayashi, Takashi; Zhu, Qiang

2012-08-01

This article describes a unique case in which both internal and external inflammatory resorption and endodontic-periodontic lesions were present at the same time in the patient's left mandibular first molar. Based on clinical and radiographic findings, it was determined that the nature of this case was a pulpal infection-induced inflammatory resorption and furcation lesion. After root canal therapy, the furcation lesion and external inflammatory resorption were completely resolved. This case indicates that the correct diagnosis of the stimulating factor for tooth resorption and determination of the primary origin of endodontic-periodontic lesions are critical for clinical management and success. Published 2011. This article is a U.S. Government work and is in the public domain in the USA.

Using Case Studies in Calculus-based Physics

NASA Astrophysics Data System (ADS)

Katz, Debora M.

2006-12-01

Do your students believe that the physics only works in your classroom or laboratory? Or do they see that physics underlies their everyday experience? Case studies in physics help students connect physics principles to their everyday experience. For decades, case studies have been used to teach law, medicine and biology, but they are rarely used in physics. I am working on a calculus-based physics textbook for scientists and engineers. Case studies are woven into each chapter. Stop by and get a case study to test out in your classroom. I would love to get your feedback.

Collaborative, case-based learning: how do students actually learn from each other?

PubMed

Thurman, Joanne; Volet, Simone E; Bolton, John R

2009-01-01

The value of collaborative, case-based, and problem-based learning has received increased attention in recent years. Several studies have documented veterinary staff and students' generally positive feedback on group learning activities, but one largely unaddressed question is how students actually learn from each other. This study examined how second-year veterinary students learned from each other during a collaborative, case-based learning project. Data were students' written reflections on their learning in the veterinary course and the specific learning experience, and a matched pre- and post-task questionnaire. Consistent with prior research describing veterinary students as individualistic learners, only a third of students spontaneously mentioned learning from each other as one of their most effective strategies. However, when prompted to describe a time when they felt that group members were really learning from each other, students reported highly valuable collaborative learning processes, which they explicitly linked to learning and understanding benefits. Questionnaire data were consistent, showing that students became more positive toward several aspects of the activity as well as toward group work in general. One unexpected finding was the lack of a relationship between students' self-evaluation of their learning and how well group members knew each other. These findings provide strong support for the educational value of collaborative, case-based learning. In light of other research evidence (using observation data) that the amount of time students actually engage in high-level collaborative processes may be rather limited, this article points to the need for veterinary teachers to better prepare students for group learning activities.

Surgical Pathology Resident Rotation Restructuring at a Tertiary Care Academic Center.

PubMed

Mehr, Chelsea R; Obstfeld, Amrom E; Barrett, Amanda C; Montone, Kathleen T; Schwartz, Lauren E

2017-01-01

Changes in the field of pathology and resident education necessitate ongoing evaluation of residency training. Evolutionary change is particularly important for surgical pathology rotations, which form the core of anatomic pathology training programs. In the past, we organized this rotation based on subjective insight. When faced with the recent need to restructure the rotation, we strove for a more evidence-based process. Our approach involved 2 primary sources of data. We quantified the number of cases and blocks submitted per case type to estimate workload and surveyed residents about the time required to gross specimens in all organ systems. A multidisciplinary committee including faculty, residents, and staff evaluated the results and used the data to model how various changes to the rotation would affect resident workload, turnaround time, and other variables. Finally, we identified rotation structures that equally distributed work and created a point-based system that capped grossing time for residents of different experience. Following implementation, we retrospectively compared turnaround time and duty hour violations before and after these changes and surveyed residents about their experiences with both systems. We evaluated the accuracy of the point-based system by examining grossing times and comparing them to the assigned point values. We found overall improvement in the rotation following the implementation. As there is essentially no literature on the subject of surgical pathology rotation organization, we hope that our experience will provide a road map to improve pathology resident education at other institutions.

Reading efficiency can be improved by minor modification of assigned duties; a pilot study on a small team of general radiologists.

PubMed

Yokota, Hajime; Goto, Mariko; Bamba, Chisa; Kiba, Maki; Yamada, Kei

2017-05-01

To assess whether alterations in the type of duty assignment system can affect the reading efficiency and stress level of diagnostic radiologists. Fourteen board-certified diagnostic radiologists were enrolled. We investigated three different reading systems for 1 week each. System 1 is our default, in which there are no assigned duties and everyone finishes when all cases are done. In system 2, two late shift readers are assigned every day, and, after everyone else leaves at a fixed time (5:30 p.m.), they take all remaining cases until they are finished. In system 3, a dedicated single reader is assigned to finish 30 cases, and everyone else will read all remaining cases. The total time required for reading and the number of cases read were recorded. In addition, participants completed two questionnaires regarding work-related stress. There was a trend toward shorter finishing time in system 2 and 3 compared to system 1 (P = 0.072 and 0.012). In terms of working stress, the subjective burden was lighter when systems 2 or 3 were employed. Minor modification of the duty assignment system has the potential to improve working efficiency and may reduce the work-related stress of diagnostic radiologists.

Surveillance of work-related asthma in new york state.

PubMed

Tice, Cori J; Cummings, Karen R; Gelberg, Kitty H

2010-04-01

The objective of this paper is to determine the percent of adults with asthma attributable to work and describe characteristics of the work-related asthma population in New York State. Sociodemographic and control characteristics of those with and without work-related asthma are compared. Data from three population-based surveys and one case-based surveillance system were analyzed. Work-relatedness of asthma was determined by self-report for the population-based surveys and by physician report for the case-based system. Self-reported sociodemographic and control characteristics were analyzed for the population-based surveys by work-relatedness. The percent of work-relatedness among adults with current asthma in New York State ranged from 10.6% to 44.5%. Significantly more adults with work-related asthma had poorly controlled asthma than those without work-related asthma. More adults with work-related asthma also tended to be employed in the manufacturing, educational services, and public administration industries than the general population. The most frequently reported exposure was dust. Adults with work-related asthma have decreased control and adverse socioeconomic impacts compared to those with asthma that is not work-related. Increased recognition and physician reporting is necessary to further prevent the impact of work-related exposures.

Evidence-based policy versus morality policy: the case of syringe access programs.

PubMed

de Saxe Zerden, Lisa; O'Quinn, Erin; Davis, Corey

2015-01-01

Evidence-based practice (EBP) combines proven interventions with clinical experience, ethics, and client preferences to inform treatment and services. Although EBP is integrated into most aspects of social work and public health, at times EBP is at odds with social policy. In this article the authors explore the paradox of evidence-based policy using syringe access programs (SAP) as a case example, and review methods of bridging the gap between the emphasis on EBP and lack of evidence informing SAP policy. Analysis includes the overuse of morality policy and examines historical and current theories why this paradox exists. Action steps are highlighted for creating effective policy and opportunities for public health change. Strategies on reframing the problem and shifting target population focus to garner support for evidence-based policy change are included. This interdisciplinary understanding of the way in which these factors converge is a critical first step in moving beyond morality-based policy toward evidence-based policy.

Changes in Student Perceptions and Study Strategies Over Time in a Veterinary Clinical Pathology Course Using Case-Based Instruction.

PubMed

Fernandez, Nicole J; Wagg, Catherine R; Warren, Amy L

2018-06-13

Veterinary students are challenged to develop new, nonlinear ways of thinking as they learn diagnostic reasoning skills. To support this process, we use real-life cases in our clinical pathology course. Changes in student perceptions regarding the use of cases and changes in study strategies over time have not been previously investigated or compared to student grades. Students participated in three voluntary online surveys that included 4-point Likert scale questions and open-ended questions on the helpfulness of cases for learning and study strategies used during the course. We used Friedman tests to detect any differences in perceptions over time; McNemar's test and "Wilcoxon signed-rank tests were used to detect any differences in study strategies over time. Fisher's exact tests'were used to examine the association between the Likert scale responses and grades in quartiles. Before beginning the course, 29% of students responded that cases were very helpful to their learning, with similar "responses for helpfulness in applying course material and grasping important concepts. There was a significant trend of increasing positivity over the duration of the course, with 74% responding that cases were very helpful at the end of the course. The most-reported study strategy was working individually on cases before the midterm (74% of students), and the most helpful study strategy was attending class regularly (88% reported it as very "helpful). Study strategies did not change significantly over time. Overall, perceptions and study strategies did not vary significantly with grades.

MathWorks Simulink and C++ integration with the new VLT PLC-based standard development platform for instrument control systems

NASA Astrophysics Data System (ADS)

Kiekebusch, Mario J.; Di Lieto, Nicola; Sandrock, Stefan; Popovic, Dan; Chiozzi, Gianluca

2014-07-01

ESO is in the process of implementing a new development platform, based on PLCs, for upcoming VLT control systems (new instruments and refurbishing of existing systems to manage obsolescence issues). In this context, we have evaluated the integration and reuse of existing C++ libraries and Simulink models into the real-time environment of BECKHOFF Embedded PCs using the capabilities of the latest version of TwinCAT software and MathWorks Embedded Coder. While doing so the aim was to minimize the impact of the new platform by adopting fully tested solutions implemented in C++. This allows us to reuse the in house expertise, as well as extending the normal capabilities of the traditional PLC programming environments. We present the progress of this work and its application in two concrete cases: 1) field rotation compensation for instrument tracking devices like derotators, 2) the ESO standard axis controller (ESTAC), a generic model-based controller implemented in Simulink and used for the control of telescope main axes.

A Novel Framework for Characterizing Exposure-Related ...

EPA Pesticide Factsheets

Descriptions of where and how individuals spend their time are important for characterizing exposures to chemicals in consumer products and in indoor environments. Herein we create an agent-based model (ABM) that is able to simulate longitudinal patterns in behaviors. By basing our ABM upon a needs-based artificial intelligence (AI) system, we create agents that mimic human decisions on these exposure-relevant behaviors. In a case study of adults, we use the AI to predict the inter-individual variation in the start time and duration of four behaviors: sleeping, eating, commuting, and working. The results demonstrate that the ABM can capture both inter-individual variation and how decisions on one behavior can affect subsequent behaviors. Preset NERL's research on the use of agent based modeling in exposure assessments. To obtain feed back on the approach from the leading experts in the field.

How long did it last? You would better ask a human

PubMed Central

Lacquaniti, Francesco; Carrozzo, Mauro; d’Avella, Andrea; La Scaleia, Barbara; Moscatelli, Alessandro; Zago, Myrka

2014-01-01

In the future, human-like robots will live among people to provide company and help carrying out tasks in cooperation with humans. These interactions require that robots understand not only human actions, but also the way in which we perceive the world. Human perception heavily relies on the time dimension, especially when it comes to processing visual motion. Critically, human time perception for dynamic events is often inaccurate. Robots interacting with humans may want to see the world and tell time the way humans do: if so, they must incorporate human-like fallacy. Observers asked to judge the duration of brief scenes are prone to errors: perceived duration often does not match the physical duration of the event. Several kinds of temporal distortions have been described in the specialized literature. Here we review the topic with a special emphasis on our work dealing with time perception of animate actors versus inanimate actors. This work shows the existence of specialized time bases for different categories of targets. The time base used by the human brain to process visual motion appears to be calibrated against the specific predictions regarding the motion of human figures in case of animate motion, while it can be calibrated against the predictions of motion of passive objects in case of inanimate motion. Human perception of time appears to be strictly linked with the mechanisms used to control movements. Thus, neural time can be entrained by external cues in a similar manner for both perceptual judgments of elapsed time and in motor control tasks. One possible strategy could be to implement in humanoids a unique architecture for dealing with time, which would apply the same specialized mechanisms to both perception and action, similarly to humans. This shared implementation might render the humanoids more acceptable to humans, thus facilitating reciprocal interactions. PMID:24478694

How long did it last? You would better ask a human.

PubMed

Lacquaniti, Francesco; Carrozzo, Mauro; d'Avella, Andrea; La Scaleia, Barbara; Moscatelli, Alessandro; Zago, Myrka

2014-01-01

In the future, human-like robots will live among people to provide company and help carrying out tasks in cooperation with humans. These interactions require that robots understand not only human actions, but also the way in which we perceive the world. Human perception heavily relies on the time dimension, especially when it comes to processing visual motion. Critically, human time perception for dynamic events is often inaccurate. Robots interacting with humans may want to see the world and tell time the way humans do: if so, they must incorporate human-like fallacy. Observers asked to judge the duration of brief scenes are prone to errors: perceived duration often does not match the physical duration of the event. Several kinds of temporal distortions have been described in the specialized literature. Here we review the topic with a special emphasis on our work dealing with time perception of animate actors versus inanimate actors. This work shows the existence of specialized time bases for different categories of targets. The time base used by the human brain to process visual motion appears to be calibrated against the specific predictions regarding the motion of human figures in case of animate motion, while it can be calibrated against the predictions of motion of passive objects in case of inanimate motion. Human perception of time appears to be strictly linked with the mechanisms used to control movements. Thus, neural time can be entrained by external cues in a similar manner for both perceptual judgments of elapsed time and in motor control tasks. One possible strategy could be to implement in humanoids a unique architecture for dealing with time, which would apply the same specialized mechanisms to both perception and action, similarly to humans. This shared implementation might render the humanoids more acceptable to humans, thus facilitating reciprocal interactions.

29 CFR 553.21 - Statutory provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... such work was any other work, the employee engaged in such work may accrue not more than 240 hours of... accrued 480 or 240 hours, as the case may be, of compensatory time off shall, for additional overtime... the employee receives such payment. (4) An employee who has accrued compensatory time off authorized...

Impulse response of a two-dimensional rough surface overlying an inhomogeneous, nondispersive medium: A hybrid model

NASA Astrophysics Data System (ADS)

Keiffer, Richard; Novarini, Jorge; Norton, Guy

2002-11-01

A numerical model to calculate the impulse response of a two-dimensional, impenetrable, rough surface directly in the time domain has been recently introduced [R. S. Keiffer and J. C. Novarini, J. Acoust. Soc. Am. 107, 27-39 (2000)]. This model is based on wedge diffraction theory and assumes the half-space containing the source and receiver is homogeneous. In this work, the model is extended to handle media where the index of refraction varies with depth by merging the scattering model with a ray-based propagation model. The resulting hybrid model is tested against a finite-difference time-domain (FDTD) method for backscattering from a corrugated surface in the presence of a refractive layer. This new model can be applied, for example, to calculate acoustic reverberation from the sea surface in cases where the water mass is inhomogeneous and dispersion is negligible. [Work supported by ONR/NRL (PE 61153N-32) and by grants of computer time DoD HPC Shared Resource Center at Stennis Space Center, MS.

Disentangling the causal relationships between work-home interference and employee health.

PubMed

van Hooff, Madelon L M; Geurts, Sabine A E; Taris, Toon W; Kompier, Michiel A J; Dikkers, Josje S E; Houtman, Irene L D; van den Heuvel, Floor M M

2005-02-01

The present study was designed to investigate the causal relationships between (time- and strain-based) work-home interference and employee health. The effort-recovery theory provided the theoretical basis for this study. Two-phase longitudinal data (with a 1-year time lag) were gathered from 730 Dutch police officers to test the following hypotheses with structural equation modeling: (i) work-home interference predicts health deterioration, (ii) health complaints precede increased levels of such interference, and (iii) both processes operate. The relationship between stable and changed levels of work-home interference across time and their relationships with the course of health were tested with a group-by-time analysis of variance. Four subgroups were created that differed in starting point and the development of work-home interference across time. The normal causal model, in which strain-based (but not time-based) work-home interference was longitudinally related to increased health complaints 1 year later, fit the data well and significantly better than the reversed causal model. Although the reciprocal model also provided a good fit, it was less parsimonious than the normal causal model. In addition, both an increment in (strain-based) work-home interference across time and a long-lasting experience of high (strain-based) work-home interference were associated with a deterioration in health. It was concluded that (strain-based) work-home interference acts as a precursor of health impairment and that different patterns of (strain-based) work-home interference across time are related to different health courses. Particularly long-term experience of (strain-based) work-home interference seems responsible for an accumulation of health complaints.

Supervised machine learning algorithms to diagnose stress for vehicle drivers based on physiological sensor signals.

PubMed

Barua, Shaibal; Begum, Shahina; Ahmed, Mobyen Uddin

2015-01-01

Machine learning algorithms play an important role in computer science research. Recent advancement in sensor data collection in clinical sciences lead to a complex, heterogeneous data processing, and analysis for patient diagnosis and prognosis. Diagnosis and treatment of patients based on manual analysis of these sensor data are difficult and time consuming. Therefore, development of Knowledge-based systems to support clinicians in decision-making is important. However, it is necessary to perform experimental work to compare performances of different machine learning methods to help to select appropriate method for a specific characteristic of data sets. This paper compares classification performance of three popular machine learning methods i.e., case-based reasoning, neutral networks and support vector machine to diagnose stress of vehicle drivers using finger temperature and heart rate variability. The experimental results show that case-based reasoning outperforms other two methods in terms of classification accuracy. Case-based reasoning has achieved 80% and 86% accuracy to classify stress using finger temperature and heart rate variability. On contrary, both neural network and support vector machine have achieved less than 80% accuracy by using both physiological signals.

[Compatibility of Work and Family Life: Survey of Physicians in the Munich Metropolitan Area].

PubMed

Lauchart, Meike; Ascher, Philipp; Kesel, Karin; Weber, Sabine; Grabein, Beatrice; Schneeweiss, Bertram; Fischer-Truestedt, Cordula; Schoenberg, Michael; Rogler, Gudrun; Borelli, Claudia

2017-05-15

Aim Investigation of the compatibility of work and family life for physicians in the Munich metropolitan area. Methods Survey of a representative sample of 1,800 physicians using a questionnaire. Results Men were less satisfied (7% very satisfied vs. 21%) with compatibility between work and family life than women. The group least satisfied overall was hospital-based physicians (p=0.000, chi-square=122.75). Women rather than men cut back their career due to children, perceived their professional advancement as impaired, desisted from establishing private practice or quit hospital employment altogether. Respondents strove for flexible childcare and makeshift solution if the established service failed. Most did not have that at their disposal. Hospital-based physicians wished for predictable working hours, and would like to have a say in the structure of their schedule. For the majority this was not the case. While for 80% it would be important to participate in the definition of their working hours, this was only possible in 17%. 86% found the opportunity to work part-time important, but many doctors (more than 30%) did not have that option. The biggest help for office-based physicians would be an expedited procedure by the Bavarian Association of Statutory Health Insurance Physicians (KVB) when applying for a proxy. The second most important would be the ability to hand over on-call duties. 36% of respondents felt that compatibility of work and family life was best achieved outside of patient care, during residency 42% believed this to be the case. Only 6% of physicians felt the best compatibility to be achieved in a hospital. Among the physician owners of practices, 34% considered their model to be the best way to reconcile both aspects of life. Conclusion More flexible options for childcare and more influence on the definition of working hours are necessary in order to better reconcile work and family life. For office-based physicians it must be made easier to find a substitute. Currently, especially women consider children as hindering their careers. Hospitals are perceived as extremely unfavorable workplaces for achieving compatibility between work and family life. © Georg Thieme Verlag KG Stuttgart · New York.

May radiofrequency be the best choice for III-IV degree hemorrhoids?

PubMed

Milito, Giovanni; Lisi, Giorgio; Aronadio, Elena; Campanelli, Michela; Venditti, Dario; Grande, Simona; Grande, Michele

2017-03-01

Hemorrhoidectomy is considered the most efficient method to treat hemorrhoids of III and IV grades. The aim of this study was to compare conventional diathermy hemorrhoidectomy and radiofrequency hemorrhoidectomy based on a large series of patients. Between June 2001 and June 2014, 1000 patients have been treated with radiofrequency hemorrhoidectomy (group A) and 500 patients have been treated with diathermy (group B) as a day-case procedure. Operating time, postoperative pain score, hospital stay, early and late postoperative complications, wound healing time and time to return to normal activities were assessed. The mean follow-up was seven years. The mean operating time for radiofrequency hemorrhoidectomy was shorter than diathermy but not significantly. Patients treated with radiofrequency had significantly less postoperative pain (measured on a Visual Analogue Scale; P=0.001), a shorter wound healing time, less time off work and postoperative complications (P=0.001) than patients who had diathermy. Neither wound healing nor mean hospital stay (day-case surgery) was significantly different. Radiofrequency hemorrhoidectomyis a valid alternative to the conventional diathermy technique, due to the reduction of operative time, postoperative pain, early and late complication rate.

A classification tree based modeling approach for segment related crashes on multilane highways.

PubMed

Pande, Anurag; Abdel-Aty, Mohamed; Das, Abhishek

2010-10-01

This study presents a classification tree based alternative to crash frequency analysis for analyzing crashes on mid-block segments of multilane arterials. The traditional approach of modeling counts of crashes that occur over a period of time works well for intersection crashes where each intersection itself provides a well-defined unit over which to aggregate the crash data. However, in the case of mid-block segments the crash frequency based approach requires segmentation of the arterial corridor into segments of arbitrary lengths. In this study we have used random samples of time, day of week, and location (i.e., milepost) combinations and compared them with the sample of crashes from the same arterial corridor. For crash and non-crash cases, geometric design/roadside and traffic characteristics were derived based on their milepost locations. The variables used in the analysis are non-event specific and therefore more relevant for roadway safety feature improvement programs. First classification tree model is a model comparing all crashes with the non-crash data and then four groups of crashes (rear-end, lane-change related, pedestrian, and single-vehicle/off-road crashes) are separately compared to the non-crash cases. The classification tree models provide a list of significant variables as well as a measure to classify crash from non-crash cases. ADT along with time of day/day of week are significantly related to all crash types with different groups of crashes being more likely to occur at different times. From the classification performance of different models it was apparent that using non-event specific information may not be suitable for single vehicle/off-road crashes. The study provides the safety analysis community an additional tool to assess safety without having to aggregate the corridor crash data over arbitrary segment lengths. Copyright © 2010. Published by Elsevier Ltd.

Robust estimation of thermodynamic parameters (ΔH, ΔS and ΔCp) for prediction of retention time in gas chromatography - Part II (Application).

PubMed

Claumann, Carlos Alberto; Wüst Zibetti, André; Bolzan, Ariovaldo; Machado, Ricardo A F; Pinto, Leonel Teixeira

2015-12-18

For this work, an analysis of parameter estimation for the retention factor in GC model was performed, considering two different criteria: sum of square error, and maximum error in absolute value; relevant statistics are described for each case. The main contribution of this work is the implementation of an initialization scheme (specialized) for the estimated parameters, which features fast convergence (low computational time) and is based on knowledge of the surface of the error criterion. In an application to a series of alkanes, specialized initialization resulted in significant reduction to the number of evaluations of the objective function (reducing computational time) in the parameter estimation. The obtained reduction happened between one and two orders of magnitude, compared with the simple random initialization. Copyright © 2015 Elsevier B.V. All rights reserved.

Algorithms for optimization of branching gravity-driven water networks

NASA Astrophysics Data System (ADS)

Dardani, Ian; Jones, Gerard F.

2018-05-01

The design of a water network involves the selection of pipe diameters that satisfy pressure and flow requirements while considering cost. A variety of design approaches can be used to optimize for hydraulic performance or reduce costs. To help designers select an appropriate approach in the context of gravity-driven water networks (GDWNs), this work assesses three cost-minimization algorithms on six moderate-scale GDWN test cases. Two algorithms, a backtracking algorithm and a genetic algorithm, use a set of discrete pipe diameters, while a new calculus-based algorithm produces a continuous-diameter solution which is mapped onto a discrete-diameter set. The backtracking algorithm finds the global optimum for all but the largest of cases tested, for which its long runtime makes it an infeasible option. The calculus-based algorithm's discrete-diameter solution produced slightly higher-cost results but was more scalable to larger network cases. Furthermore, the new calculus-based algorithm's continuous-diameter and mapped solutions provided lower and upper bounds, respectively, on the discrete-diameter global optimum cost, where the mapped solutions were typically within one diameter size of the global optimum. The genetic algorithm produced solutions even closer to the global optimum with consistently short run times, although slightly higher solution costs were seen for the larger network cases tested. The results of this study highlight the advantages and weaknesses of each GDWN design method including closeness to the global optimum, the ability to prune the solution space of infeasible and suboptimal candidates without missing the global optimum, and algorithm run time. We also extend an existing closed-form model of Jones (2011) to include minor losses and a more comprehensive two-part cost model, which realistically applies to pipe sizes that span a broad range typical of GDWNs of interest in this work, and for smooth and commercial steel roughness values.

A medical/vocational case coordination system for persons with brain injury: an evaluation of employment outcomes.

PubMed

Malec, J F; Buffington, A L; Moessner, A M; Degiorgio, L

2000-08-01

To evaluate initial placement and 1-year employment outcomes of a Medical/Vocational Case Coordination System (MVCCS) for persons with brain injury (BI) that provides: (1) early case identification and coordination, (2) appropriate medical and vocational rehabilitation interventions, (3) work trials, and (4) supported employment interventions including job coaching. One hundred fourteen Minnesota residents, ages 18 to 65 years, with acquired BI. Five levels of Vocational Independence Scale (VIS). Preinjury employment status (VIS) and years of education, severity of initial injury, time since injury, current impairment/disability as measured by the Rasch-analyzed Staff Mayo-Portland Adaptability Inventory (MPAI), and impaired self-awareness measured by staff rating and the difference between Staff MPAI and Survivor MPAI. At placement, 46% in independent work; 25% in transitional placements; 9% in long-term supported employment; 10% in sheltered work; and 10% not placed. At 1-year follow-up (n = 101), 53% in independent work; 19% in transitional placement; 9% in supported work; 6% in sheltered work; and 13% unemployed. Regression analyses showed time since injury and Rasch Staff MPAI predicted VIS at placement; only VIS at placement independently predicted VIS at 1-year follow-up; Rasch Staff MPAI and preinjury education level predicted time to placement. The MVCCS optimized vocational outcome after BI. Time since injury and impairment/disability best predicted vocational placement. Level of initial placement best predicted employment status at follow-up. Persons with greater disability required more extended time and more extensive rehabilitation services before placement.

Long-term follow-up of HAN-1, an acute plutonium oxide inhalation case

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbaugh, E.H.; Bihl, D.E.; Sula, M.J.

1990-06-01

The International Commission on Radiation Protection (ICRP) has recommended that plutonium oxide be designated an inhalation class Y material, indicating that a 500-day clearance half-time from the lung is adequate for radiation protection purposes. Based on extensive data obtained from one particular inhalation case (referred to here as HAN-1), and supported by somewhat less detailed data in nine other cases, an argument has been put forth that substantially longer clearance half-times may not be uncommon for Pu oxide. This has led to the tentative identification of a super class Y'' form of Pu which has been factored into worker monitoringmore » programs at the US Department of Energy's Hanford Site. In addition, the United States Transuranium Registry autopsy work has indicted evidence to support the super class Y case. The particular case described in this paper was the key case which caused the Hanford internal dosimetry staff to seriously consider super class Y material. This paper includes data from long-term follow up monitoring as well as early data for calculating intakes for comparisons with secondary limits. 13 refs, 2 figs., 1 tab.« less

What the Person Brings to the Table: Personality, Coping, and Work-Family Conflict

ERIC Educational Resources Information Center

Andreassi, Jeanine K.

2011-01-01

Employees (N = 291) of various industries and companies were surveyed to study how individual factors (coping and personality) affect work-family conflict: strain-based work-to-family conflict (S-WFC), time-based work-to-family conflict (T-WFC), strain-based family-to-work conflict (S-FWC), and time-based family-to-work conflict (T-FWC). As…

COLLABORATE©: A Universal Competency-Based Paradigm for Professional Case Management, Part II: Competency Clarification.

PubMed

Treiger, Teresa M; Fink-Samnick, Ellen

2013-01-01

The purpose of this second article of a 3-article series is to clarify the competencies for a new paradigm of case management built upon a value-driven foundation that : Applicable to all health care sectors where case management is practiced. In moving forward, the one fact that rings true is that there will be a constant change in our industry. As the health care terrain shifts and new influences continually surface, there will be consequences for case management practice. These impacts require nimble clinical professionals in possession of recognized and firmly established competencies. They must be agile to frame (and reframe) their professional practice to facilitate the best possible outcomes for their patients. Case managers can choose to be Gumby™ or Pokey™. This is exactly the time to define a competency-based case management model, highlighting one sufficiently fluid to fit into any setting of care. The practice of case management transcends the vast array of representative professional disciplines and educational levels. A majority of current models are driven by business priorities rather than the competencies critical to successful practice and quality patient outcomes. This results in a fragmented professional case management identity. Although there is an inherent value in what each discipline brings to the table, this advanced model unifies behind case management's unique, strengths-based identity instead of continuing to align within traditional divisions (e.g., discipline, work setting, population served). This model fosters case management's expanding career advancement opportunities, including a reflective clinical ladder.

A price- and-time-slot-negotiation mechanism for Cloud service reservations.

PubMed

Son, Seokho; Sim, Kwang Mong

2012-06-01

When making reservations for Cloud services, consumers and providers need to establish service-level agreements through negotiation. Whereas it is essential for both a consumer and a provider to reach an agreement on the price of a service and when to use the service, to date, there is little or no negotiation support for both price and time-slot negotiations (PTNs) for Cloud service reservations. This paper presents a multi-issue negotiation mechanism to facilitate the following: 1) PTNs between Cloud agents and 2) tradeoff between price and time-slot utilities. Unlike many existing negotiation mechanisms in which a negotiation agent can only make one proposal at a time, agents in this work are designed to concurrently make multiple proposals in a negotiation round that generate the same aggregated utility, differing only in terms of individual price and time-slot utilities. Another novelty of this work is formulating a novel time-slot utility function that characterizes preferences for different time slots. These ideas are implemented in an agent-based Cloud testbed. Using the testbed, experiments were carried out to compare this work with related approaches. Empirical results show that PTN agents reach faster agreements and achieve higher utilities than other related approaches. A case study was carried out to demonstrate the application of the PTN mechanism for pricing Cloud resources.

Dynamic Geometry Capture with a Multi-View Structured-Light System

DTIC Science & Technology

2014-12-19

funding was never a problem during my studies . One of the best parts of my time at UC Berkeley has been working with colleagues within the Video and...scientific and medical applications such as quantifying improvement in physical therapy and measuring unnatural poses in ergonomic studies . Specifically... cases with limited scene texture. This direct generation of surface geometry provides us with a distinct advantage over multi-camera based systems. For

The World of Work between the Personal and the Collective: A Demand for Social Justice and Guidance for Latin America

ERIC Educational Resources Information Center

Bello, Julio Gonzalez; Chacón, Omaira

2015-01-01

The struggle for justice has been permanent for a very long period of time. In this sense, it could be said that since Plato conceived it as one of the fundamental virtues, justice has constituted a goal to achieve for any society. In the case of justice, related to social aspects, the situation has been overwhelming in Latin America. Based on a…

Challenging evidence-based decision-making: a hypothetical case study about return to work.

PubMed

Aas, Randi W; Alexanderson, Kristina

2012-03-01

A hypothetical case study about return to work was used to explore the process of translating research into practice. The method involved constructing a case study derived from the characteristics of a typical, sick-listed employee with non-specific low back pain in Norway. Next, the five-step evidence-based process, including the Patient, Intervention, Co-Interventions and Outcome framework (PICO), was applied to the case study. An inductive analysis produced 10 technical and more fundamental challenges to incorporate research into intervention decisions for an individual with comorbidity. A more dynamic, interactive approach to the evidence-based practice process is proposed. It is recommended that this plus the 10 challenges are validated with real life cases, as the hypothetical case study may not be replicable. Copyright © 2011 John Wiley & Sons, Ltd.

Work-based learning experiences help students with disabilities transition to careers: a case study of University of Washington projects.

PubMed

Bellman, Scott; Burgstahler, Sheryl; Ladner, Richard

2014-01-01

This case study describes evidence-based practices employed by a collection of University of Washington projects that engage high school and postsecondary students with disabilities in work-based learning experiences such as industry and research internships, career development activities, job shadows, field trips, and mock interviews. The purpose of the article is two-fold. First, authors share best practices with others who wish to increase the participation of students with disabilities in work-based learning and thereby contribute to their academic and career success. The article discusses methods used to recruit students, employers and mentors, match students with specific opportunities, and prepare students for success. Second, authors share outcomes from studies regarding participation in these work-based learning opportunities, which include increased employment success, motivation to work toward a career, knowledge about careers and the workplace, job-related skills, ability to work with supervisors and coworkers, skills in self-advocating for accommodations, and perceived career options.

Development of a Web-based Glaucoma Registry at King Khaled Eye Specialist Hospital, Saudi Arabia: A Cost-Effective Methodology

PubMed Central

Zaman, Babar; Khandekar, Rajiv; Al Shahwan, Sami; Song, Jonathan; Al Jadaan, Ibrahim; Al Jiasim, Leyla; Owaydha, Ohood; Asghar, Nasira; Hijazi, Amar; Edward, Deepak P.

2014-01-01

In this brief communication, we present the steps used to establish a web-based congenital glaucoma registry at our institution. The contents of a case report form (CRF) were developed by a group of glaucoma subspecialists. Information Technology (IT) specialists used Lime Survey softwareTM to create an electronic CRF. A MY Structured Query Language (MySQL) server was used as a database with a virtual machine operating system. Two ophthalmologists and 2 IT specialists worked for 7 hours, and a biostatistician and a data registrar worked for 24 hours each to establish the electronic CRF. Using the CRF which was transferred to the Lime survey tool, and the MYSQL server application, data could be directly stored in spreadsheet programs that included Microsoft Excel, SPSS, and R-Language and queried in real-time. In a pilot test, clinical data from 80 patients with congenital glaucoma were entered into the registry and successful descriptive analysis and data entry validation was performed. A web-based disease registry was established in a short period of time in a cost-efficient manner using available resources and a team-based approach. PMID:24791112

Development of a web-based glaucoma registry at King Khaled Eye Specialist Hospital, Saudi Arabia: a cost-effective methodology.

PubMed

Zaman, Babar; Khandekar, Rajiv; Al Shahwan, Sami; Song, Jonathan; Al Jadaan, Ibrahim; Al Jiasim, Leyla; Owaydha, Ohood; Asghar, Nasira; Hijazi, Amar; Edward, Deepak P

2014-01-01

In this brief communication, we present the steps used to establish a web-based congenital glaucoma registry at our institution. The contents of a case report form (CRF) were developed by a group of glaucoma subspecialists. Information Technology (IT) specialists used Lime Survey softwareTM to create an electronic CRF. A MY Structured Query Language (MySQL) server was used as a database with a virtual machine operating system. Two ophthalmologists and 2 IT specialists worked for 7 hours, and a biostatistician and a data registrar worked for 24 hours each to establish the electronic CRF. Using the CRF which was transferred to the Lime survey tool, and the MYSQL server application, data could be directly stored in spreadsheet programs that included Microsoft Excel, SPSS, and R-Language and queried in real-time. In a pilot test, clinical data from 80 patients with congenital glaucoma were entered into the registry and successful descriptive analysis and data entry validation was performed. A web-based disease registry was established in a short period of time in a cost-efficient manner using available resources and a team-based approach.

TRADITIONAL CANISTER-BASED OPEN WASTE MANAGEMENT SYSTEM VERSUS CLOSED SYSTEM: HAZARDOUS EXPOSURE PREVENTION AND OPERATING THEATRE STAFF SATISFACTION.

PubMed

Horn, M; Patel, N; MacLellan, D M; Millard, N

2016-06-01

Exposure to blood and body fluids is a major concern to health care professionals working in operating rooms (ORs). Thus, it is essential that hospitals use fluid waste management systems that minimise risk to staff, while maximising efficiency. The current study compared the utility of a 'closed' system with a traditional canister-based 'open' system in the OR in a private hospital setting. A total of 30 arthroscopy, urology, and orthopaedic cases were observed. The closed system was used in five, four, and six cases, respectively and the open system was used in nine, two, and four cases, respectively. The average number of opportunities for staff to be exposed to hazardous fluids were fewer for the closed system when compared to the open during arthroscopy and urology procedures. The open system required nearly 3.5 times as much staff time for set-up, maintenance during procedures, and post-procedure disposal of waste. Theatre staff expressed greater satisfaction with the closed system than with the open. In conclusion, compared with the open system, the closed system offers a less hazardous and more efficient method of disposing of fluid waste generated in the OR.

Case-based discussion supporting learning and practice in optometry.

PubMed

Bullock, Alison; Barnes, Emma; Ryan, Barbara; Sheen, Nik

2014-09-01

To enhance continuing professional development and address the risk that professional isolation poses, the UK General Optical Council introduced a requirement for all optometrists to engage in at least one case-based discussion per 3 year cycle of continuing education. In this paper, we explore participants' impression of the acceptability, effectiveness and long-term impact-on-practice of case-based discussion as a mode of continuing education. Case-based discussion participants attended an evening session comprising a lecture and a group discussion. They completed three questionnaires: prior to the session, immediately post-session and 3-4 months post-session. We coded the questionnaires to allow matching. Seventy-five case-based discussion groups were held with 379 participants; 377 completed both pre- and post-questionnaires and 331 (88%) returned a follow-up questionnaire. Case-based discussions were an acceptable method of learning, with many preferring it to distance-learning. Prior to the event, women, employees and part-time workers were more likely to have concerns about participating. In terms of learning, gaps in knowledge were more likely to be revealed in those who work in isolation. The respondents highlighted social aspects, reassurance of practice as well as new learning. Participants significantly improved self-confidence ratings in all key learning areas. At three months post-session, the majority (75%) self-reported that they had implemented their intended changes to practice. The evaluation showed that participants felt that case-based discussion developed their knowledge, notably for sole practitioners, and influenced later workplace practice. The peer interaction of this mode of continuing education can combat professional isolation. © 2014 The Authors Ophthalmic & Physiological Optics © 2014 The College of Optometrists.

The time course of cancer detection performance

NASA Astrophysics Data System (ADS)

Taylor-Phillips, Sian; Clarke, Aileen; Wallis, Matthew; Wheaton, Margot; Duncan, Alison; Gale, Alastair G.

2011-03-01

The purpose of this study was to measure how mammography readers' performance varies with time of day and time spent reading. This was investigated in screening practice and when reading an enriched case set. In screening practice records of time and date that each case was read, along with outcome (whether the woman was recalled for further tests, and biopsy results where performed) was extracted from records from one breast screening centre in UK (4 readers). Patterns of performance with time spent reading was also measured using an enriched test set (160 cases, 41% malignant, read three times by eight radiologists). Recall rates varied with time of day, with different patterns for each reader. Recall rates decreased as the reading session progressed both when reading the enriched test set and in screening practice. Further work is needed to expand this work to a greater number of breast screening centres, and to determine whether these patterns of performance over time can be used to optimize overall performance.

Postgraduate Work-Based Learning Programmes in English Higher Education: Exploring Case Studies of Organizational Practice

ERIC Educational Resources Information Center

Smith, Paul; Preece, David

2009-01-01

The first part of the paper outlines and discusses the nature of work-based learning (WBL) and WBL programmes, and the overall direction of government strategy towards WBL programmes in Higher Education (HE) in England, with particular reference to postgraduate programmes, policy documents, and the WBL literature. Drawing upon case study research,…

Balint work and the creation of medical knowledge.

PubMed

Muench, John

2018-01-01

Michael Balint's pioneering work in primary care was not simply the application of psychodynamic theory to the complex problems and relationships encountered by clinicians. Rather, Balint's work was part of a wider conversation in Western epistemology that had already begun to break down the enlightenment rationalist agenda. Since the time of Descartes, we sought to find certain truth through decontextualizing and abstracting problems, and through separation of the observer from the thing observed, with a focus on finding universal timeless laws that could be generalized. By the mid-1950s, it was clear that this agenda was insufficient to answer important questions about what it means to be human and to live a healthy and happy life. Balint's experiment was a return to a method of knowledge creation that is case based, narrative, local, timely, particular, and especially considers specific contexts for finding solutions to problems. For current healthcare reform efforts to be effective, we must include Balint's focus on the context of the doctor, patient, and their relationship, as well as development of practical wisdom (i.e. Aristotelian phronesis) that we know in medicine as professional judgment. The case study method of the Balint group is one of the few and best formal methods to teach and practice this way of knowing.

Position-based dynamic of a particle system: a configurable algorithm to describe complex behaviour of continuum material starting from swarm robotics

NASA Astrophysics Data System (ADS)

dell'Erba, Ramiro

2018-04-01

In a previous work, we considered a two-dimensional lattice of particles and calculated its time evolution by using an interaction law based on the spatial position of the particles themselves. The model reproduced the behaviour of deformable bodies both according to the standard Cauchy model and second gradient theory; this success led us to use this method in more complex cases. This work is intended as the natural evolution of the previous one in which we shall consider both energy aspects, coherence with the principle of Saint Venant and we start to manage a more general tool that can be adapted to different physical phenomena, supporting complex effects like lateral contraction, anisotropy or elastoplasticity.

Schedule-Aware Workflow Management Systems

NASA Astrophysics Data System (ADS)

Mans, Ronny S.; Russell, Nick C.; van der Aalst, Wil M. P.; Moleman, Arnold J.; Bakker, Piet J. M.

Contemporary workflow management systems offer work-items to users through specific work-lists. Users select the work-items they will perform without having a specific schedule in mind. However, in many environments work needs to be scheduled and performed at particular times. For example, in hospitals many work-items are linked to appointments, e.g., a doctor cannot perform surgery without reserving an operating theater and making sure that the patient is present. One of the problems when applying workflow technology in such domains is the lack of calendar-based scheduling support. In this paper, we present an approach that supports the seamless integration of unscheduled (flow) and scheduled (schedule) tasks. Using CPN Tools we have developed a specification and simulation model for schedule-aware workflow management systems. Based on this a system has been realized that uses YAWL, Microsoft Exchange Server 2007, Outlook, and a dedicated scheduling service. The approach is illustrated using a real-life case study at the AMC hospital in the Netherlands. In addition, we elaborate on the experiences obtained when developing and implementing a system of this scale using formal techniques.

The Health Service Bus: an architecture and case study in achieving interoperability in healthcare.

PubMed

Ryan, Amanda; Eklund, Peter

2010-01-01

Interoperability in healthcare is a requirement for effective communication between entities, to ensure timely access to up to-date patient information and medical knowledge, and thus facilitate consistent patient care. An interoperability framework called the Health Service Bus (HSB), based on the Enterprise Service Bus (ESB) middleware software architecture is presented here as a solution to all three levels of interoperability as defined by the HL7 EHR Interoperability Work group in their definitive white paper "Coming to Terms". A prototype HSB system was implemented based on the Mule Open-Source ESB and is outlined and discussed, followed by a clinically-based example.

Continuum Fatigue Damage Modeling for Use in Life Extending Control

NASA Technical Reports Server (NTRS)

Lorenzo, Carl F.

1994-01-01

This paper develops a simplified continuum (continuous wrp to time, stress, etc.) fatigue damage model for use in Life Extending Controls (LEC) studies. The work is based on zero mean stress local strain cyclic damage modeling. New nonlinear explicit equation forms of cyclic damage in terms of stress amplitude are derived to facilitate the continuum modeling. Stress based continuum models are derived. Extension to plastic strain-strain rate models are also presented. Application of these models to LEC applications is considered. Progress toward a nonzero mean stress based continuum model is presented. Also, new nonlinear explicit equation forms in terms of stress amplitude are also derived for this case.

Turbomachinery

NASA Technical Reports Server (NTRS)

Simoneau, Robert J.; Strazisar, Anthony J.; Sockol, Peter M.; Reid, Lonnie; Adamczyk, John J.

1987-01-01

The discipline research in turbomachinery, which is directed toward building the tools needed to understand such a complex flow phenomenon, is based on the fact that flow in turbomachinery is fundamentally unsteady or time dependent. Success in building a reliable inventory of analytic and experimental tools will depend on how the time and time-averages are treated, as well as on who the space and space-averages are treated. The raw tools at disposal (both experimentally and computational) are truly powerful and their numbers are growing at a staggering pace. As a result of this power, a case can be made that a situation exists where information is outstripping understanding. The challenge is to develop a set of computational and experimental tools which genuinely increase understanding of the fluid flow and heat transfer in a turbomachine. Viewgraphs outline a philosophy based on working on a stairstep hierarchy of mathematical and experimental complexity to build a system of tools, which enable one to aggressively design the turbomachinery of the next century. Examples of the types of computational and experimental tools under current development at Lewis, with progress to date, are examined. The examples include work in both the time-resolved and time-averaged domains. Finally, an attempt is made to identify the proper place for Lewis in this continuum of research.

Generating macroscopic chaos in a network of globally coupled phase oscillators

PubMed Central

So, Paul; Barreto, Ernest

2011-01-01

We consider an infinite network of globally coupled phase oscillators in which the natural frequencies of the oscillators are drawn from a symmetric bimodal distribution. We demonstrate that macroscopic chaos can occur in this system when the coupling strength varies periodically in time. We identify period-doubling cascades to chaos, attractor crises, and horseshoe dynamics for the macroscopic mean field. Based on recent work that clarified the bifurcation structure of the static bimodal Kuramoto system, we qualitatively describe the mechanism for the generation of such complicated behavior in the time varying case. PMID:21974662

Improving health care costing with resource consumption accounting.

PubMed

Ozyapici, Hasan; Tanis, Veyis Naci

2016-07-11

Purpose - The purpose of this paper is to explore the differences between a traditional costing system (TCS) and resource consumption accounting (RCA) based on a case study carried out in a hospital. Design/methodology/approach - A descriptive case study was first carried out to identify the current costing system of the case hospital. An exploratory case study was then conducted to reveal how implementing RCA within the case hospital assigns costs differently to gallbladder surgeries than the current costing system (i.e. a TCS). Findings - The study showed that, in contrast to a TCS, RCA considers the unused capacity, which is the difference between the work that can be performed based on current resources and the work that is actually being performed. Therefore, it assigns lower total costs to open and laparoscopic gallbladder surgeries. The study also showed that by separating costs into fixed and variable RCA allows managers to benefit from a pricing strategy based on the difference between the service's selling price and variable costs incurred in providing that service. Research limitations/implications - The limitation of this study is that, because of time constraints, the implementation was performed in the general surgery department only. However, since RCA is an advanced system that has the same application procedures for any department inside in a hospital, managers need only time gaps to implement this system to all parts of the hospital. Practical implications - This study concluded that RCA is better than a TCS for use in health care settings that have high overhead costs because it accurately assigns overhead costs to services by considering unused capacities incurred by a hospital. Consequently, this study provides insight into both measuring and managing unused capacities within the health care sector. This study also concluded that RCA helps health care administrators increase their competitive advantage by allowing them to determine the lowest service price. Originality/value - Since the literature review found no study comparing RCA with TCS in a real-life health care setting, little is known about differences arising from applying these systems in this context. Thus, the current study fills this gap in the literature by comparing RCA with TCS for both open and laparoscopic gallbladder surgeries.

Work-Based Learning: A Practical Approach for Learning to Work and Working to Learn. A Case Study on Decision-Makers' Professional Development in Iran

ERIC Educational Resources Information Center

Arani, Mohammad Reza Sarkar; Alagamandan, Jafar; Tourani, Heidar

2004-01-01

The work-based learning model of human resource development has captured a great deal of attention and has gained increasing importance in higher education in recent years. Work-based learning is a powerful phenomenon that attempts to help policy-makers, managers and curriculum developers improve the quality of the decision and organizational…

Time-optical spinup maneuvers of flexible spacecraft

NASA Technical Reports Server (NTRS)

Singh, G.; Kabamba, P. T.; Mcclamroch, N. H.

1990-01-01

Attitude controllers for spacecraft have been based on the assumption that the bodies being controlled are rigid. Future spacecraft, however, may be quite flexible. Many applications require spinning up/down these vehicles. In this work the minimum time control of these maneuvers is considered. The time-optimal control is shown to possess an important symmetry property. Taking advantage of this property, the necessary and sufficient conditions for optimality are transformed into a system of nonlinear algebraic equations in the control switching times during one half of the maneuver, the maneuver time, and the costates at the mid-maneuver time. These equations can be solved using a homotopy approach. Control spillover measures are introduced and upper bounds on these measures are obtained. For a special case these upper bounds can be expressed in closed form for an infinite dimensional evaluation model. Rotational stiffening effects are ignored in the optimal control analysis. Based on a heuristic argument a simple condition is given which justifies the omission of these nonlinear effects. This condition is validated by numerical simulation.

Background on Establishing a Working Group to Create Home Clinical Cases for Education.

PubMed

Yoshitake, Taketo

2017-01-01

In Japan there are concerns that there will be a surge in social insurance costs such as medical and nursing care expenses as a result of the baby boom generation reaching the late stages of old age (75 years old and beyond) around 2025 ("The 2025 Problem"). In 2012, the "Outline on Social Insurance and Tax Reform" was approved by the Japanese cabinet and government, including "construction of regional comprehensive care". To promote participation in home medical care by pharmacists, this article presents the roles demanded of pharmacists in regional comprehensive care from the standpoint of physicians, and the discussion of case studies bridging the gap from knowledge learned in lectures to practical applications. In the field of medical education, "The 2023 Problem", regarding standards of education on a global level, caused medical schools across Japan to scramble for curriculum reform, specifically in the demand for increased time spent in clinical training and the expansion of community-based medical education. The current state of community-based medical education will be reviewed. In light of these developments, "the working group to create home clinical cases for education" was developed by clinical pharmacists in the field and university faculty members at Daiichi University of Pharmacy.

Generalizing DTW to the multi-dimensional case requires an adaptive approach

PubMed Central

Hu, Bing; Jin, Hongxia; Wang, Jun; Keogh, Eamonn

2017-01-01

In recent years Dynamic Time Warping (DTW) has emerged as the distance measure of choice for virtually all time series data mining applications. For example, virtually all applications that process data from wearable devices use DTW as a core sub-routine. This is the result of significant progress in improving DTW’s efficiency, together with multiple empirical studies showing that DTW-based classifiers at least equal (and generally surpass) the accuracy of all their rivals across dozens of datasets. Thus far, most of the research has considered only the one-dimensional case, with practitioners generalizing to the multi-dimensional case in one of two ways, dependent or independent warping. In general, it appears the community believes either that the two ways are equivalent, or that the choice is irrelevant. In this work, we show that this is not the case. The two most commonly used multi-dimensional DTW methods can produce different classifications, and neither one dominates over the other. This seems to suggest that one should learn the best method for a particular application. However, we will show that this is not necessary; a simple, principled rule can be used on a case-by-case basis to predict which of the two methods we should trust at the time of classification. Our method allows us to ensure that classification results are at least as accurate as the better of the two rival methods, and, in many cases, our method is significantly more accurate. We demonstrate our ideas with the most extensive set of multi-dimensional time series classification experiments ever attempted. PMID:29104448

Night work and breast cancer: a population-based case-control study in France (the CECILE study).

PubMed

Menegaux, Florence; Truong, Thérèse; Anger, Antoinette; Cordina-Duverger, Emilie; Lamkarkach, Farida; Arveux, Patrick; Kerbrat, Pierre; Févotte, Joëlle; Guénel, Pascal

2013-02-15

Night work involving disruption of circadian rhythm was suggested as a possible cause of breast cancer. We examined the role of night work in a large population-based case-control study carried out in France between 2005 and 2008. Lifetime occupational history including work schedules of each night work period was elicited in 1,232 cases of breast cancer and 1,317 population controls. Thirteen percent of the cases and 11% of the controls had ever worked on night shifts (OR = 1.27 [95% confidence interval = 0.99-1.64]). Odds ratios were 1.35 [1.01-1.80] in women who worked on overnight shifts, 1.40 [1.01-1.92] in women who had worked at night for 4.5 or more years, and 1.43 [1.01-2.03] in those who worked less than three nights per week on average. The odds ratio was 1.95 [1.13-3.35] in women employed in night work for >4 years before their first full-term pregnancy, a period where mammary gland cells are incompletely differentiated and possibly more susceptible to circadian disruption effects. Our results support the hypothesis that night work plays a role in breast cancer, particularly in women who started working at night before first full-term pregnancy. Copyright © 2012 UICC.

Fairness in optimizing bus-crew scheduling process.

PubMed

Ma, Jihui; Song, Cuiying; Ceder, Avishai Avi; Liu, Tao; Guan, Wei

2017-01-01

This work proposes a model considering fairness in the problem of crew scheduling for bus drivers (CSP-BD) using a hybrid ant-colony optimization (HACO) algorithm to solve it. The main contributions of this work are the following: (a) a valid approach for cases with a special cost structure and constraints considering the fairness of working time and idle time; (b) an improved algorithm incorporating Gamma heuristic function and selecting rules. The relationships of each cost are examined with ten bus lines collected from the Beijing Public Transport Holdings (Group) Co., Ltd., one of the largest bus transit companies in the world. It shows that unfair cost is indirectly related to common cost, fixed cost and extra cost and also the unfair cost approaches to common and fixed cost when its coefficient is twice of common cost coefficient. Furthermore, the longest time for the tested bus line with 1108 pieces, 74 blocks is less than 30 minutes. The results indicate that the HACO-based algorithm can be a feasible and efficient optimization technique for CSP-BD, especially with large scale problems.

Image selection in static telepathology through the Internet.

PubMed

Della Mea, V; Cataldi, P; Boi, S; Finato, N; Della Palma, P; Beltrami, C A

1998-01-01

A telepathology study was carried out to examine the differences occurring when the images were selected by an experienced pathologist, a junior pathologist and a first-year resident. One hundred and fifty-five consecutive frozen-section pathology cases were collected and sent for consultation to a remote experienced pathologist using multimedia email. Local diagnoses (as reported in the files of the Institute, not from the image selector) and remote diagnoses (based on the images) were compared with those performed on paraffin-embedded sections. Acquisition time and number of selected images were recorded for each case and used to compare the different behaviour of the three local pathologists. Of the 155 cases sent by telepathology, four were considered insufficient for a diagnosis by the remote pathologist and thus the diagnosis was postponed. In the remaining 151 cases, the overall diagnostic agreement between remote and definitive diagnosis was 96.7%. The results indicate that in the routine diagnostic work of a frozen-section service, an inexperienced pathologist can select images which are sufficiently informative for a remote diagnosis, in a sufficiently short time.

What Do Primary Students Say about School-Based Social Work Programmes?

ERIC Educational Resources Information Center

Testa, Doris

2014-01-01

This article focuses on primary school children's experiences of school-based social work programmes. These students, aged between 6 and 11, and drawn from a student population comprising 28 different cultural backgrounds and from low socio-economic backgrounds, participated in a case study that researched a school-based social work programme, the…

29 CFR 553.221 - Compensable hours of work.

Code of Federal Regulations, 2011 CFR

2011-07-01

... time (§ 553.222) apply to both law enforcement and firefighting employees for whom the section 7(k) exemption is claimed. Also, special rules for meal time apply in the case of employees in fire protection... independent employer, early relief, and work performed on an occasional or sporadic and part-time basis, all...

Time motion analysis of nursing work in ICU, telemetry and medical-surgical units.

PubMed

Schenk, Elizabeth; Schleyer, Ruth; Jones, Cami R; Fincham, Sarah; Daratha, Kenn B; Monsen, Karen A

2017-11-01

This study examined nurses' work, comparing nursing interventions and locations across three units in a United States hospital using Omaha System standardized terminology as the organizing framework. The differences in nurses' acute-care work across unit types are not well understood. Prior investigators have used time-motion methodologies; few have compared differences across units, nor used standardized terminology. Nurse-observers recorded locations and interventions of nurses on three acute-care units using hand-held devices and web-based TimeCaT ™ software. Nursing interventions were mapped to Omaha System terms. Unit-differences were analysed. Nurses changed locations approximately every 2 min, and averaged approximately one intervention/minute. Unit differences were found in both the interventions performed and the locations. Most interventions were case-management related, demonstrating the nurses' patient management/coordination role. Unit differences in nursing interventions and location were found among three unit types. Omaha System terminology, as well as the observational method used, were found to be feasible and practical. Nursing work varies by unit, yet managers have not been armed with empirical data with which to make more informed decisions about nurses' work priorities, clinical outcomes, patient satisfaction, staff satisfaction and cost. The results from this study will help them to do so. © 2017 John Wiley & Sons Ltd.

Dating furniture and coopered vessels without waney edge - Reconstructing historical wood-working in Austria with the help of dendrochronology.

PubMed

Klein, Andrea; Nemestothy, Sebastian; Kadnar, Julia; Grabner, Michael

In the present study, 208 furniture and 168 coopered vessels from three Austrian museums were examined. Dendrochronology was used to date objects and to extract further information such as the necessary time for seasoning, wood loss through wood-working and methods of construction. In most cases sampling was done by sanding the cross section and making digital photographs using a picture frame and measuring digitally. The dendrochronological dates of the sampled furniture range between 1524 and 1937. The group of furniture includes cupboards, chests, tables, benches, commodes and beds. In many cases furniture was artfully painted and sometimes even shows a painted year. With the help of dendrochronology it was proved that some objects had been painted for some time after construction, or had been over-painted. Most furniture, however, was painted immediately after completion. In this case, the seasoning and storage time of the boards and the wood loss due to shaping can be verified. As an average value, 14 years have passed between the dendrochronological date of the outermost ring and the painting. The time span includes time of seasoning and storage and the rings lost by wood-working. This leads, on the one hand to a short storage time of less than 10 years and on the other hand to very little wood loss due to manufacturing. Those boards being less shaped turned out to be back panels of cupboards, therefore they are recommended to be sampled for dating. Coopered vessels were dated between 1612 and 1940. There was evidence that staves were split and not sawn in many cases. The staves were often split out of the outermost part of the tree and hardly any wood was worked away which was proved by the close dendrochronological dates of the single staves of a vessel. Since there is a short time of storage and only little wood loss through wood-working, dating of objects without a waney edge becomes reasonable.

Path generation algorithm for UML graphic modeling of aerospace test software

NASA Astrophysics Data System (ADS)

Qu, MingCheng; Wu, XiangHu; Tao, YongChao; Chen, Chao

2018-03-01

Aerospace traditional software testing engineers are based on their own work experience and communication with software development personnel to complete the description of the test software, manual writing test cases, time-consuming, inefficient, loopholes and more. Using the high reliability MBT tools developed by our company, the one-time modeling can automatically generate test case documents, which is efficient and accurate. UML model to describe the process accurately express the need to rely on the path is reached, the existing path generation algorithm are too simple, cannot be combined into a path and branch path with loop, or too cumbersome, too complicated arrangement generates a path is meaningless, for aerospace software testing is superfluous, I rely on our experience of ten load space, tailor developed a description of aerospace software UML graphics path generation algorithm.

Pilot Project Technology Business Case: Mobile Work Packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Ken; Lawrie, Sean; Niedermuller, Josef

Performance advantages of the new pilot project technologies are widely acknowledged, but it has proven difficult for utilities to derive business cases for justifying investment in these new capabilities. Lack of a business case is often cited by utilities as a barrier to pursuing wide-scale application of digital technologies to nuclear plant work activities. The decision to move forward with funding usually hinges on demonstrating actual cost reductions that can be credited to budgets and thereby truly reduce O&M or capital costs. Technology enhancements, while enhancing work methods and making work more efficient, often fail to eliminate workload such thatmore » it changes overall staffing and material cost requirements. It is critical to demonstrate cost reductions or impacts on non-cost performance objectives in order for the business case to justify investment by nuclear operators. The Business Case Methodology (BCM) was developed in September of 2015 to frame the benefit side of II&C technologies to address the “benefit” side of the analysis—as opposed to the cost side—and how the organization evaluates discretionary projects (net present value (NPV), accounting effects of taxes, discount rates, etc.). The cost and analysis side is not particularly difficult for the organization and can usually be determined with a fair amount of precision (not withstanding implementation project cost overruns). It is in determining the “benefits” side of the analysis that utilities have more difficulty in technology projects and that is the focus of this methodology. The methodology is presented in the context of the entire process, but the tool provided is limited to determining the organizational benefits only. This report describes a the use of the BCM in building a business case for mobile work packages, which includes computer-based procedures and other automated elements of a work package. Key to those impacts will be identifying where the savings are “harvestable,” meaning they result in an actual reduction in headcount and/or cost. The report describes the specific activities conducted with a partner utility to examine the various work activities associated with mobile work packages to determine what time savings and error rate reductions are available. The report summarizes these findings in the form of a business case for the technology.« less

TH-E-BRF-05: Comparison of Survival-Time Prediction Models After Radiotherapy for High-Grade Glioma Patients Based On Clinical and DVH Features

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magome, T; Haga, A; Igaki, H

Purpose: Although many outcome prediction models based on dose-volume information have been proposed, it is well known that the prognosis may be affected also by multiple clinical factors. The purpose of this study is to predict the survival time after radiotherapy for high-grade glioma patients based on features including clinical and dose-volume histogram (DVH) information. Methods: A total of 35 patients with high-grade glioma (oligodendroglioma: 2, anaplastic astrocytoma: 3, glioblastoma: 30) were selected in this study. All patients were treated with prescribed dose of 30–80 Gy after surgical resection or biopsy from 2006 to 2013 at The University of Tokyomore » Hospital. All cases were randomly separated into training dataset (30 cases) and test dataset (5 cases). The survival time after radiotherapy was predicted based on a multiple linear regression analysis and artificial neural network (ANN) by using 204 candidate features. The candidate features included the 12 clinical features (tumor location, extent of surgical resection, treatment duration of radiotherapy, etc.), and the 192 DVH features (maximum dose, minimum dose, D95, V60, etc.). The effective features for the prediction were selected according to a step-wise method by using 30 training cases. The prediction accuracy was evaluated by a coefficient of determination (R{sup 2}) between the predicted and actual survival time for the training and test dataset. Results: In the multiple regression analysis, the value of R{sup 2} between the predicted and actual survival time was 0.460 for the training dataset and 0.375 for the test dataset. On the other hand, in the ANN analysis, the value of R{sup 2} was 0.806 for the training dataset and 0.811 for the test dataset. Conclusion: Although a large number of patients would be needed for more accurate and robust prediction, our preliminary Result showed the potential to predict the outcome in the patients with high-grade glioma. This work was partly supported by the JSPS Core-to-Core Program(No. 23003) and Grant-in-aid from the JSPS Fellows.« less

Four-year incidence of sick leave because of neck and shoulder pain and its association with work and lifestyle.

PubMed

Alipour, Akbar; Ghaffari, Mostafa; Shariati, Batoul; Jensen, Irene; Vingard, Eva

2009-02-15

Four-year prospective cohort study. To find the incidence of sick leave because of neck and shoulder pain (NSP) in industrial workers, and its association with work and lifestyle risk factors. Longitudinal studies to investigate NSP incidence and risk factors are rare, and even fewer have been conducted in middle- and low-income countries. After inviting all full-time employees of an Iranian car manufacturing company with 18,031 employees to participate in a baseline study, they were followed for 4 years. New episodes of sick leave because of NSP have been calculated based on sickness absence registration between the years 2003 and 2007. The incidence was compared for participants and nonparticipants. The association between sick leave, physical, and psychosocial risk factors at work, and previous self-reported NSP, was calculated for the remaining population of baseline participants (12,184 employees) during a 4-year follow-up. During a 4-year follow-up of study subjects for the remaining participants of the baseline study, the incidence of sick leave was 0.8% (98 sick leave cases in 12,184 employees). For nonparticipants this incidence was 4.2% (130 cases in 3127 employees). In the final regression model for sick leave cases, the remaining factors for potential physical risk factors were repetitive work and sitting positions at work; for psychosocial factors unattractive work was the only significant remaining factor. The incidence of NSP based on sick leave is definitely very low compared with previous studies in high-income countries. This incidence varies between participants and nonparticipants. Risk factors for sick leave differ from risk factors for self-reported pain. A young population, job security, the insurance system, different health behaviors, and healthy worker bias, are all factors that may affect the results, and sick-leave as an outcome must be interpreted with more caution in middle- and low-income countries.

Husband/Wife Differentials in Household Work Time: The Case of Dual-Earner Families.

ERIC Educational Resources Information Center

Abdel-Ghany, Mohamed; Nickols, Sharon Y.

1983-01-01

Inspite of the tremendous increase in the burden of market work faced by married American women in the last decade, the differential in household work time between husbands and wives still persists. The results of this study assert that the differences in socioeconomic characteristics between husbands and wives explain only part of that…

Equal Pay Act: Wage Differentials for Time of Day Worked

ERIC Educational Resources Information Center

Stanford, Richard Alan

1974-01-01

The Supreme Court held in Corning Glass Works cases involving male only employees for night shifts that the time of day worked could constitute a factor other than sex whereby the wage differential might qualify as an exception under the Equal Pay Act. Shift differentials could be legal if proven to be nondiscriminatory. (LBH)

"It's Time": A Case for the Professionalisation of Youth Work

ERIC Educational Resources Information Center

Emslie, Michael

2012-01-01

Michael Emslie argues that the time is right for youth work in Australia to be professionalised in line with other human service practices such as nursing, education and psychology. He identifies a groundswell of activities that support the professionalisation of youth work and a concurrent growth in high-level interest in strengthening social and…

Construction and validation of a low-cost surgical trainer based on iPhone technology for training laparoscopic skills.

PubMed

Pérez Escamirosa, Fernando; Ordorica Flores, Ricardo; Minor Martínez, Arturo

2015-04-01

In this article, we describe the construction and validation of a laparoscopic trainer using an iPhone 5 and a plastic document holder case. The abdominal cavity was simulated with a clear plastic document holder case. On 1 side of the case, 2 holes for entry of laparoscopic instruments were drilled. We added a window to place the camera of the iPhone, which works as our camera of the trainer. Twenty residents carried out 4 tasks using the iPhone Trainer and a physical laparoscopic trainer. The time of all tasks were analyzed with a simple paired t test. The construction of the trainer took 1 hour, with a cost of

A Framework of Combining Case-Based Reasoning with a Work Breakdown Structure for Estimating the Cost of Online Course Production Projects

ERIC Educational Resources Information Center

He, Wu

2014-01-01

Currently, a work breakdown structure (WBS) approach is used as the most common cost estimation approach for online course production projects. To improve the practice of cost estimation, this paper proposes a novel framework to estimate the cost for online course production projects using a case-based reasoning (CBR) technique and a WBS. A…

Improving real-time efficiency of case-based reasoning for medical diagnosis.

PubMed

Park, Yoon-Joo

2014-01-01

Conventional case-based reasoning (CBR) does not perform efficiently for high volume dataset because of case-retrieval time. Some previous researches overcome this problem by clustering a case-base into several small groups, and retrieve neighbors within a corresponding group to a target case. However, this approach generally produces less accurate predictive performances than the conventional CBR. This paper suggests a new case-based reasoning method called the Clustering-Merging CBR (CM-CBR) which produces similar level of predictive performances than the conventional CBR with spending significantly less computational cost.

Design of high-performance parallelized gene predictors in MATLAB.

PubMed

Rivard, Sylvain Robert; Mailloux, Jean-Gabriel; Beguenane, Rachid; Bui, Hung Tien

2012-04-10

This paper proposes a method of implementing parallel gene prediction algorithms in MATLAB. The proposed designs are based on either Goertzel's algorithm or on FFTs and have been implemented using varying amounts of parallelism on a central processing unit (CPU) and on a graphics processing unit (GPU). Results show that an implementation using a straightforward approach can require over 4.5 h to process 15 million base pairs (bps) whereas a properly designed one could perform the same task in less than five minutes. In the best case, a GPU implementation can yield these results in 57 s. The present work shows how parallelism can be used in MATLAB for gene prediction in very large DNA sequences to produce results that are over 270 times faster than a conventional approach. This is significant as MATLAB is typically overlooked due to its apparent slow processing time even though it offers a convenient environment for bioinformatics. From a practical standpoint, this work proposes two strategies for accelerating genome data processing which rely on different parallelization mechanisms. Using a CPU, the work shows that direct access to the MEX function increases execution speed and that the PARFOR construct should be used in order to take full advantage of the parallelizable Goertzel implementation. When the target is a GPU, the work shows that data needs to be segmented into manageable sizes within the GFOR construct before processing in order to minimize execution time.

A nested case-control study of fatal work related injuries among Brazilian steel workers.

PubMed Central

Barreto, S M; Swerdlow, A J; Smith, P G; Higgins, C D

1997-01-01

OBJECTIVES: To estimate the relative risk of death from work related injury in a steelworks, associated with exposure to various occupational hazards, sociodemographic factors, and medical history. MATERIAL AND METHODS: The study was a nested case-control design. It was based on a cohort of men employed in the steel plant of USIMINAS, Brazil between January 1977 and August 1990, who were followed up to November 1992. The cases were defined as all workers in the cohort who died from injury in the study period and whose death had been notified to the Brazilian Ministry of Labour as being related to work. Four controls per case, matched to cases on year of birth, were randomly selected from among workers employed in the plant at the time of death of the matching case. Data on potential risk factors for occupational injury were extracted from company records; for the controls these data were abstracted for the period preceding the death of the matching case. RESULTS: There were 37 deaths related to work injuries during the study period. Four surviving workers were selected as controls for each case, but for eight the personnel records were incomplete, leaving 140 controls in all. Significantly increased risk of fatal injury related to work was associated with exposure to noise, heat, dust and fumes, gases and vapours, rotating shift work, being a manual worker, and working in the steel mill, coke ovens, blast furnaces, and energy and water supply areas. Risk of fatal injury related to work increased with intensity of exposure to noise (P (trend) = 0.004) and heat (P < 0.001), and increased greatly with a hazard score that combined information on noise, heat, dust, and gas exposure (P < 0.001). Number of years of schooling (P = 0.03) and salary level (P = 0.03) were both negatively associated with risk. In a multivariate analysis including all these significant factors, only hazard score and area of work remained associated with death from injury related to work. The highest risks were for men exposed to all four environmental hazards (odds ratio (OR) 19.4; 95% confidence interval (95% CI) 1.1 to 352.1) and those working in the energy supply area (OR 18.0; 1.6 to 198.1). CONCLUSIONS: The study identified parts of the steelworks and types of hazard associated with greatly increased risk of fatal accident. Research and measures to prevent accidents need to concentrate on these areas and the people working in them. The use of a hazard score was successful in identifying high risk, and similar scoring might prove useful in other industrial situations. PMID:9326164

Time-based analysis of total cost of patient episodes: a case study of hip replacement.

PubMed

Peltokorpi, Antti; Kujala, Jaakko

2006-01-01

Healthcare in the public and private sectors is facing increasing pressure to become more cost-effective. Time-based competition and work-in-progress have been used successfully to measure and improve the efficiency of industrial manufacturing. Seeks to address this issue. Presents a framework for time based management of the total cost of a patient episode and apply it to the six sigma DMAIC-process development approach. The framework is used to analyse hip replacement patient episodes in Päijät-Häme Hospital District in Finland, which has a catchment area of 210,000 inhabitants and performs an average of 230 hip replacements per year. The work-in-progress concept is applicable to healthcare--notably that the DMAIC-process development approach can be used to analyse the total cost of patient episodes. Concludes that a framework, which combines the patient-in-process and the DMAIC development approach, can be used not only to analyse the total cost of patient episode but also to improve patient process efficiency. Presents a framework that combines patient-in-process and DMAIC-process development approaches, which can be used to analyse the total cost of a patient episode in order to improve patient process efficiency.

Night work, long work weeks, and risk of accidental injuries. A register-based study.

PubMed

Larsen, Ann D; Hannerz, Harald; Møller, Simone V; Dyreborg, Johnny; Bonde, Jens Peter; Hansen, Johnni; Kolstad, Henrik A; Hansen, Åse Marie; Garde, Anne Helene

2017-11-01

Objectives The aims of this study were to (i) investigate the association between night work or long work weeks and the risk of accidental injuries and (ii) test if the association is affected by age, sex or socioeconomic status. Methods The study population was drawn from the Danish version of the European Labour Force Survey from 1999-2013. The current study was based on 150 438 participants (53% men and 47% women). Data on accidental injuries were obtained at individual level from national health registers. We included all 20-59-year-old employees working ≥32 hours a week at the time of the interview. We used Poisson regression to estimate the relative rates (RR) of accidental injuries as a function of night work or long work weeks (>40 hours per week) adjusted for year of interview, sex, age, socioeconomic status (SES), industry, and weekly working hours or night work. Age, sex and SES were included as two-way interactions. Results We observed 23 495 cases of accidental injuries based on 273 700 person years at risk. Exposure to night work was statistically significantly associated with accidental injuries (RR 1.11, 99% CI 1.06-1.17) compared to participants with no recent night work. No associations were found between long work weeks (>40 hours) and accidental injuries. Conclusion We found a modest increased risk of accidental injuries when reporting night work. No associations between long work weeks and risk of accidental injuries were observed. Age, sex and SES showed no trends when included as two-way interactions.

WELDSMART: A vision-based expert system for quality control

NASA Technical Reports Server (NTRS)

Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

1992-01-01

This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and successfully demosntrated to work illustrates that the general approach taken here appears to be promising for commercial development of computerized quality inspection systems. Inspection based on these techniques may be used to supplement or substitute more elaborate inspection methods, such as x-ray inspections.

The Development of Time-Based Prospective Memory in Childhood: The Role of Working Memory Updating

ERIC Educational Resources Information Center

Voigt, Babett; Mahy, Caitlin E. V.; Ellis, Judi; Schnitzspahn, Katharina; Krause, Ivonne; Altgassen, Mareike; Kliegel, Matthias

2014-01-01

This large-scale study examined the development of time-based prospective memory (PM) across childhood and the roles that working memory updating and time monitoring play in driving age effects in PM performance. One hundred and ninety-seven children aged 5 to 14 years completed a time-based PM task where working memory updating load was…

The effect of Burns & Wounds (B&W)/burdock leaf therapy on burn-injured Amish patients: a pilot study measuring pain levels, infection rates, and healing times.

PubMed

Kolacz, Nicole M; Jaroch, Mark T; Bear, Monica L; Hess, Rosanna F

2014-12-01

The purposes of this pilot study were to measure pain associated with dressing changes, assess the presence of infection, and document healing times of burn-injured Amish in central Ohio using an herbal therapy consisting of Burns and Wounds™ ointment (B&W) and burdock (Arctium ssp.) leaves. B&W contains honey, lanolin, olive oil, wheat germ oil, marshmallow root, Aloe vera gel, wormwood, comfrey root, white oak bark, lobelia inflata, vegetable glycerin, bees wax, and myrrh. A prospective, case series design guided the study within a community-based participatory research framework. Amish burn dressers provided burn care. Registered nurses monitored each case and documented findings. Pain scores were noted and burns were inspected for infection during dressing changes; healing times were measured from day of burn to complete closure of the skin. All cases were photographed. Between October 2011 and May 2013, five Amish were enrolled. All had first- and second-degree burns. B&W/burdock leaf dressing changes caused minimal or no pain; none of the burns became infected, and healing times averaged less than 14 days. The use of this herbal remedy appears to be an acceptable alternative to conventional burn care for these types of burns. The trauma of dressing changes was virtually nonexistent. Nurses working in communities with Amish residents should be aware of this herbal-based method of burn care and monitor its use when feasible. © The Author(s) 2014.

A case-based assistant for clinical psychiatry expertise.

PubMed

Bichindaritz, I

1994-01-01

Case-based reasoning is an artificial intelligence methodology for the processing of empirical knowledge. Recent case-based reasoning systems also use theoretic knowledge about the domain to constrain the case-based reasoning. The organization of the memory is the key issue in case-based reasoning. The case-based assistant presented here has two structures in memory: cases and concepts. These memory structures permit it to be as skilled in problem-solving tasks, such as diagnosis and treatment planning, as in interpretive tasks, such as clinical research. A prototype applied to clinical work about eating disorders in psychiatry, reasoning from the alimentary questionnaires of these patients, is presented as an example of the system abilities.

The combined positive impact of Lean methodology and Ventana Symphony autostainer on histology lab workflow

PubMed Central

2010-01-01

Background Histologic samples all funnel through the H&E microtomy staining area. Here manual processes intersect with semi-automated processes creating a bottleneck. We compare alternate work processes in anatomic pathology primarily in the H&E staining work cell. Methods We established a baseline measure of H&E process impact on personnel, information management and sample flow from historical workload and production data and direct observation. We compared this to performance after implementing initial Lean process modifications, including workstation reorganization, equipment relocation and workflow levelling, and the Ventana Symphony stainer to assess the impact on productivity in the H&E staining work cell. Results Average time from gross station to assembled case decreased by 2.9 hours (12%). Total process turnaround time (TAT) exclusive of processor schedule changes decreased 48 minutes/case (4%). Mean quarterly productivity increased 8.5% with the new methods. Process redesign reduced the number of manual steps from 219 to 182, a 17% reduction. Specimen travel distance was reduced from 773 ft/case to 395 ft/case (49%) overall, and from 92 to 53 ft/case in the H&E cell (42% improvement). Conclusions Implementation of Lean methods in the H&E work cell of histology can result in improved productivity, improved through-put and case availability parameters including TAT. PMID:20181123

Model-Based Systems Engineering With the Architecture Analysis and Design Language (AADL) Applied to NASA Mission Operations

NASA Technical Reports Server (NTRS)

Munoz Fernandez, Michela Miche

2014-01-01

The potential of Model Model Systems Engineering (MBSE) using the Architecture Analysis and Design Language (AADL) applied to space systems will be described. AADL modeling is applicable to real-time embedded systems- the types of systems NASA builds. A case study with the Juno mission to Jupiter showcases how this work would enable future missions to benefit from using these models throughout their life cycle from design to flight operations.

Working with a fixed operating room team on consecutive similar cases and the effect on case duration and turnover time.

PubMed

Stepaniak, Pieter S; Vrijland, Wietske W; de Quelerij, Marcel; de Vries, Guus; Heij, Christiaan

2010-12-01

If variation in procedure times could be controlled or better predicted, the cost of surgeries could be reduced through improved scheduling of surgical resources. This study on the impact of similar consecutive cases on the turnover, surgical, and procedure times tests the perception that repeating the same manual tasks reduces the duration of these tasks. We hypothesize that when a fixed team works on similar consecutive cases the result will be shorter turnover and procedure duration as well as less variation as compared with the situation without a fixed team. Case-control study. St Franciscus Hospital, a large general teaching hospital in Rotterdam, the Netherlands. Two procedures, inguinal hernia repair and laparoscopic cholecystectomy, were selected and divided across a control group and a study group. Patients were randomly assigned to the study or control group. Preparation time, surgical time, procedure time, and turnover time. For inguinal hernia repair, we found a significantly lower preparation time and 10 minutes less procedure time in the study group, as compared with the control group. Variation in the study group was lower, as compared with the control group. For laparoscopic cholecystectomy, preparation time was significantly lower in the study group, as compared with the control group. For both procedures, there was a significant decrease in turnover time. Scheduling similar consecutive cases and performing with a fixed team results in lower turnover times and preparation times. The procedure time of the inguinal hernia repair decreased significantly and has practical scheduling implications. For more complex surgery, like laparoscopic cholecystectomy, there is no effect on procedure time.

Persistent work-life conflict and health satisfaction - A representative longitudinal study in Switzerland

PubMed Central

2011-01-01

Background The objectives of the present study were (1) to track work-life conflict in Switzerland during the years 2002 to 2008 and (2) to analyse the relationship between work-life conflict and health satisfaction, examining whether long-term work-life conflict leads to poor health satisfaction. Methods The study is based on a representative longitudinal database (Swiss Household Panel), covering a six-year period containing seven waves of data collection. The sample includes 1261 persons, with 636 men and 625 women. Data was analysed by multi-level mixed models and analysis of variance with repeated measures. Results In the overall sample, there was no linear increase or decrease of work-life conflict detected, in either its time-based or strain-based form. People with higher education were more often found to have a strong work-life conflict (time- and strain-based), and more men demonstrated a strong time-based work-life conflict than women (12.2% vs. 5%). A negative relationship between work-life conflict and health satisfaction over time was found. People reporting strong work-life conflict at every wave reported lower health satisfaction than people with consistently weak work-life conflict. However, the health satisfaction of those with a continuously strong work-life conflict did not decrease during the study period. Conclusions Both time-based and strain-based work-life conflict are strongly correlated to health satisfaction. However, no evidence was found for a persistent work-life conflict leading to poor health satisfaction. PMID:21529345

Persistent work-life conflict and health satisfaction - a representative longitudinal study in Switzerland.

PubMed

Knecht, Michaela K; Bauer, Georg F; Gutzwiller, Felix; Hämmig, Oliver

2011-04-29

The objectives of the present study were (1) to track work-life conflict in Switzerland during the years 2002 to 2008 and (2) to analyse the relationship between work-life conflict and health satisfaction, examining whether long-term work-life conflict leads to poor health satisfaction. The study is based on a representative longitudinal database (Swiss Household Panel), covering a six-year period containing seven waves of data collection. The sample includes 1261 persons, with 636 men and 625 women. Data was analysed by multi-level mixed models and analysis of variance with repeated measures. In the overall sample, there was no linear increase or decrease of work-life conflict detected, in either its time-based or strain-based form. People with higher education were more often found to have a strong work-life conflict (time- and strain-based), and more men demonstrated a strong time-based work-life conflict than women (12.2% vs. 5%). A negative relationship between work-life conflict and health satisfaction over time was found. People reporting strong work-life conflict at every wave reported lower health satisfaction than people with consistently weak work-life conflict. However, the health satisfaction of those with a continuously strong work-life conflict did not decrease during the study period. Both time-based and strain-based work-life conflict are strongly correlated to health satisfaction. However, no evidence was found for a persistent work-life conflict leading to poor health satisfaction.

Arnold diffusion for a complete family of perturbations

NASA Astrophysics Data System (ADS)

Delshams, Amadeu; Schaefer, Rodrigo G.

2017-01-01

In this work we illustrate the Arnold diffusion in a concrete example — the a priori unstable Hamiltonian system of 2 + 1/2 degrees of freedom H( p, q, I, φ, s) = p 2/2+ cos q - 1 + I 2/2 + h( q, φ, s; ɛ) — proving that for any small periodic perturbation of the form h( q, φ, s; ɛ) = ɛ cos q ( a 00 + a 10 cos φ + a 01 cos s) ( a 10 a 01 ≠ 0) there is global instability for the action. For the proof we apply a geometrical mechanism based on the so-called scattering map. This work has the following structure: In the first stage, for a more restricted case ( I* π/2 μ, μ = a 10/ a 01), we use only one scattering map, with a special property: the existence of simple paths of diffusion called highways. Later, in the general case we combine a scattering map with the inner map (inner dynamics) to prove the more general result (the existence of instability for any μ). The bifurcations of the scattering map are also studied as a function of μ. Finally, we give an estimate for the time of diffusion, and we show that this time is primarily the time spent under the scattering map.

A Framework to Improve Energy Efficient Behaviour at Home through Activity and Context Monitoring

PubMed Central

García, Óscar; Alonso, Ricardo S.; Corchado, Juan M.

2017-01-01

Real-time Localization Systems have been postulated as one of the most appropriated technologies for the development of applications that provide customized services. These systems provide us with the ability to locate and trace users and, among other features, they help identify behavioural patterns and habits. Moreover, the implementation of policies that will foster energy saving in homes is a complex task that involves the use of this type of systems. Although there are multiple proposals in this area, the implementation of frameworks that combine technologies and use Social Computing to influence user behaviour have not yet reached any significant savings in terms of energy. In this work, the CAFCLA framework (Context-Aware Framework for Collaborative Learning Applications) is used to develop a recommendation system for home users. The proposed system integrates a Real-Time Localization System and Wireless Sensor Networks, making it possible to develop applications that work under the umbrella of Social Computing. The implementation of an experimental use case aided efficient energy use, achieving savings of 17%. Moreover, the conducted case study pointed to the possibility of attaining good energy consumption habits in the long term. This can be done thanks to the system’s real time and historical localization, tracking and contextual data, based on which customized recommendations are generated. PMID:28758987

Improving ethical knowledge and sensemaking from cases through elaborative interrogation and outcome valence.

PubMed

Johnson, James F; Bagdasarov, Zhanna; MacDougall, Alexandra E; Steele, Logan; Connelly, Shane; Devenport, Lynn D; Mumford, Michael D

2014-01-01

The case-based approach to learning is popular among many applied fields. However, results of case-based education vary widely on case content and case presentation. This study examined two aspects of case-based education-outcome valence and case elaboration methods-in a two-day case-based Responsible Conduct of Research (RCR) ethics education program. Results suggest that outcome information is an integral part of a quality case. Furthermore, valence consistent outcomes may have certain advantages over mixed valence outcome information. Finally, students enjoy and excel working with case material, and the use of elaborative interrogation techniques can significantly improve internally-focused ethical sensemaking strategies associated with personal biases, constraints, and emotions.

Symmetric and antisymmetric forms of the Pauli master equation

PubMed Central

Klimenko, A. Y.

2016-01-01

When applied to matter and antimatter states, the Pauli master equation (PME) may have two forms: time-symmetric, which is conventional, and time-antisymmetric, which is suggested in the present work. The symmetric and antisymmetric forms correspond to symmetric and antisymmetric extensions of thermodynamics from matter to antimatter — this is demonstrated by proving the corresponding H-theorem. The two forms are based on the thermodynamic similarity of matter and antimatter and differ only in the directions of thermodynamic time for matter and antimatter (the same in the time-symmetric case and the opposite in the time-antisymmetric case). We demonstrate that, while the symmetric form of PME predicts an equibalance between matter and antimatter, the antisymmetric form of PME favours full conversion of antimatter into matter. At this stage, it is impossible to make an experimentally justified choice in favour of the symmetric or antisymmetric versions of thermodynamics since we have no experience of thermodynamic properties of macroscopic objects made of antimatter, but experiments of this kind may become possible in the future. PMID:27440454

Dominant takeover regimes for genetic algorithms

NASA Technical Reports Server (NTRS)

Noever, David; Baskaran, Subbiah

1995-01-01

The genetic algorithm (GA) is a machine-based optimization routine which connects evolutionary learning to natural genetic laws. The present work addresses the problem of obtaining the dominant takeover regimes in the GA dynamics. Estimated GA run times are computed for slow and fast convergence in the limits of high and low fitness ratios. Using Euler's device for obtaining partial sums in closed forms, the result relaxes the previously held requirements for long time limits. Analytical solution reveal that appropriately accelerated regimes can mark the ascendancy of the most fit solution. In virtually all cases, the weak (logarithmic) dependence of convergence time on problem size demonstrates the potential for the GA to solve large N-P complete problems.

A national survey of candidates: II: motivations, obstacles, and ideas on increasing interest in psychoanalytic training.

PubMed

Katz, Debra A; Kaplan, Marcia; Stromberg, Sarah E

2012-10-01

A national survey of candidates was conducted to identify motivations for pursuing psychoanalytic training, obstacles that prevent progression or completion, and candidates' ideas on how best to increase interest among potential trainees. In 2009-2010, 40 percent of candidates on the affiliate member e-mail list completed an anonymous web-based survey. Candidates strongly endorsed contact with a personal psychotherapist, psychoanalyst, or supervisor as the most important influence in discovering psychoanalysis and deciding to pursue training. They identified the total cost of analytic training as the greatest obstacle. This was followed by the cost of personal analysis, loss of income for low-fee cases, time away from family, and difficulty finding cases. To enhance training, local institutes should work to improve institute atmosphere and provide assistance with finding cases; national organizations should increase outreach activities and publicize psychoanalysis. Psychoanalytic institutes could recruit future candidates by working to increase personal contact with psychoanalysts, reducing the cost of training, improving institute atmosphere, assisting with case-finding, enhancing outreach activities, and widely publicizing psychoanalysis. Narrative comments from candidates and the implications of these findings regarding engagement of future trainees are discussed.

Sub-fragmentation of structural-reactive-material casings under explosion

NASA Astrophysics Data System (ADS)

Zhang, Fan

2015-06-01

The sub-fragmentation of structural reactive material (SRM) thick-casings is to generate fine fragments during casing fragmentation under explosive loading for their efficient energy release to enhance air blast. This has been investigated using a cylindrical casing made from either rich Al-MoO3 or Al-W-based granular composites. The former composite was to study the concept of reactive hot spots where the reaction of reactive particles, which were distributed into base SRM in a fuel-rich equivalence ratio, created heat and gas products during SRM fragmentation. The expansion of these distributed hot spots initiated local fractures of the casing, leading to fine fragments. The Al-W-based composite investigated the concept of impedance mismatch, where shock dynamics at the interfaces of different impedance ingredients resulted in non-uniform, high local temperatures and stresses and late in times the dissimilar inertia resulted in different accelerations, leading to material separation and fine fragments. The casings were manufactured through both hot iso-static pressing and cold gas dynamic spray deposition. Explosion experiments were conducted in a 3 m diameter, 23 m3 cylindrical chamber for these cased charges in a casing-to-explosive mass ratio of 1.75. The results demonstrated the presence of fine fragments and more efficient fragment combustion, compared with previous results, and indicated the effectiveness of both concepts. This work was jointly funded by Defence R&D Canada and the Advanced Energetics Program of DTRA (Dr. William H. Wilson).

Upper limb musculoskeletal complaints among technicians working in a diagnostic tuberculosis laboratory: two case reports.

PubMed

Wong, Joyce Y P; Chin, David; Fung, Henry; Li, Ann; Wong, Marcus M S; Kwok, Henry K H

2014-01-01

Upper limb musculoskeletal complaints are common among certain health professionals. We report two cases, both involving technicians working in a diagnostic tuberculosis laboratory in Hong Kong. A work process evaluation suggest that the need to repeatedly open and close small bottles, as well as to work for prolonged periods of time in confined areas, could be related to the workers' clinical presentation. The cases are also compatible with the diagnosis of repetitive strain injury (RSI) of the upper limb, but this term is not commonly used nowadays because of various definitional issues. A review of the various diagnostic issues in RSI is presented.

Effort-reward imbalance and work ability: cross-sectional and longitudinal findings from the Second German Sociomedical Panel of Employees

PubMed Central

2012-01-01

Background Although data from longitudinal studies are sparse, effort-reward imbalance (ERI) seems to affect work ability. However, the potential pathway from restricted work ability to ERI must also be considered. Therefore, the aim of our study was to analyse cross-sectional and longitudinal associations between ERI and work ability and vice versa. Methods Data come from the Second German Sociomedical Panel of Employees. Logistic regression models were estimated to determine cross-sectional and longitudinal associations. The sample used to predict new cases of poor or moderate work ability was restricted to cases with good or excellent work ability at baseline. The sample used to predict new cases of ERI was restricted to persons without ERI at baseline. Results The cross-sectional analysis included 1501 full-time employed persons. The longitudinal analyses considered 600 participants with good or excellent baseline work ability and 666 participants without baseline ERI, respectively. After adjustment for socio-demographic variables, health-related behaviour and factors of the work environment, ERI was cross-sectionally associated with poor or moderate work ability (OR = 1.980; 95% CI: 1.428 to 2.747). Longitudinally, persons with ERI had 2.1 times higher odds of poor or moderate work ability after one year (OR = 2.093; 95% CI: 1.047 to 4.183). Conversely, persons with poor or moderate work ability had 2.6 times higher odds of an ERI after one year (OR = 2.573; 95% CI: 1.314 to 5.041). Conclusions Interventions that enable workers to cope with ERI or address indicators of ERI directly could promote the maintenance of work ability. Integration management programmes for persons with poor work ability should also consider their psychosocial demands. PMID:23067110

Effects of the European Working Time Directive on anaesthetic training in the United Kingdom.

PubMed

Sim, D J; Wrigley, S R; Harris, S

2004-08-01

Decreases in the hours worked by trainee anaesthetists are being brought about by both the New Deal for Trainees and the European Working Time Directive. Anticipated improvements in health and safety achieved by a decrease in hours will be at the expense of training time if the amount of night-time work remains constant. This audit examined the effects of a change from a partial to a full shift system on a cohort of trainee anaesthetists working in a large district general hospital in the South-west of England. Logbook and list analyses were performed for two 10-week periods: one before and one after the decrease in hours. An 18% decrease in the number of cases done and an 11% decrease in the number of weekly training lists were found for specialist registrars. A 22% decrease in the number of cases done and a 14% decrease in the number of weekly training lists were found for senior house officers. Furthermore, a decrease of one service list per specialist registrar per week was seen, which will have implications for consultant manpower requirements.

Intraoperative computed tomography with integrated navigation system in a multidisciplinary operating suite.

PubMed

Uhl, Eberhard; Zausinger, Stefan; Morhard, Dominik; Heigl, Thomas; Scheder, Benjamin; Rachinger, Walter; Schichor, Christian; Tonn, Jörg-Christian

2009-05-01

We report our preliminary experience in a prospective series of patients with regard to feasibility, work flow, and image quality using a multislice computed tomographic (CT) scanner combined with a frameless neuronavigation system (NNS). A sliding gantry 40-slice CT scanner was installed in a preexisting operating room. The scanner was connected to a frameless infrared-based NNS. Image data was transferred directly from the scanner into the navigation system. This allowed updating of the NNS during surgery by automated image registration based on the position of the gantry. Intraoperative CT angiography was possible. The patient was positioned on a radiolucent operating table that fits within the bore of the gantry. During image acquisition, the gantry moved over the patient. This table allowed all positions and movements like any normal operating table without compromising the positioning of the patient. For cranial surgery, a carbon-made radiolucent head clamp was fixed to the table. Experience with the first 230 patients confirms the feasibility of intraoperative CT scanning (136 patients with intracranial pathology, 94 patients with spinal lesions). After a specific work flow, interruption of surgery for intraoperative scanning can be limited to 10 to 15 minutes in cranial surgery and to 9 minutes in spinal surgery. Intraoperative imaging changed the course of surgery in 16 of the 230 cases either because control CT scans showed suboptimal screw position (17 of 307 screws, with 9 in 7 patients requiring correction) or that tumor resection was insufficient (9 cases). Intraoperative CT angiography has been performed in 7 cases so far with good image quality to determine residual flow in an aneurysm. Image quality was excellent in spinal and cranial base surgery. The system can be installed in a preexisting operating environment without the need for special surgical instruments. It increases the safety of the patient and the surgeon without necessitating a change in the existing surgical protocol and work flow. Imaging and updating of the NNS can be performed at any time during surgery with very limited time and modification of the surgical setup. Multidisciplinary use increases utilization of the system and thus improves the cost-efficiency relationship.

Combining Reaction Time and Accuracy: The Relationship Between Working Memory Capacity and Task Switching as a Case Example.

PubMed

Draheim, Christopher; Hicks, Kenny L; Engle, Randall W

2016-01-01

It is generally agreed upon that the mechanisms underlying task switching heavily depend on working memory, yet numerous studies have failed to show a strong relationship between working memory capacity (WMC) and task-switching ability. We argue that this relationship does indeed exist but that the dependent variable used to measure task switching is problematic. To support our claim, we reanalyzed data from two studies with a new scoring procedure that combines reaction time (RT) and accuracy into a single score. The reanalysis revealed a strong relationship between task switching and WMC that was not present when RT-based switch costs were used as the dependent variable. We discuss the theoretical implications of this finding along with the potential uses and limitations of the scoring procedure we used. More broadly, we emphasize the importance of using measures that incorporate speed and accuracy in other areas of research, particularly in comparisons of subjects differing in cognitive and developmental levels. © The Author(s) 2015.

Remote Control and Data Acquisition: A Case Study

NASA Technical Reports Server (NTRS)

DeGennaro, Alfred J.; Wilkinson, R. Allen

2000-01-01

This paper details software tools developed to remotely command experimental apparatus, and to acquire and visualize the associated data in soft real time. The work was undertaken because commercial products failed to meet the needs. This work has identified six key factors intrinsic to development of quality research laboratory software. Capabilities include access to all new instrument functions without any programming or dependence on others to write drivers or virtual instruments, simple full screen text-based experiment configuration and control user interface, months of continuous experiment run-times, order of 1% CPU load for condensed matter physics experiment described here, very little imposition of software tool choices on remote users, and total remote control from anywhere in the world over the Internet or from home on a 56 Kb modem as if the user is sitting in the laboratory. This work yielded a set of simple robust tools that are highly reliable, resource conserving, extensible, and versatile, with a uniform simple interface.

Prostate carcinoma mimicking a sphenoid wing meningioma

PubMed Central

Bradley, Lucas H.; Burton, Matthew; Gokden, Murat; Serletis, Demitre

2015-01-01

Introduction We report here on a rare case of a large, lateral sphenoid wing tumor with radiographic and intraoperative findings highly suggestive of meningioma, yet pathology was in fact consistent with metastatic prostate adenocarcinoma. Presentation of case An 81 year-old male presented with expressive dysphasia, right-sided weakness and headaches. Imaging revealed a heterogeneously-enhancing lesion based on the left lateral sphenoid wing. The presumed diagnosis was strongly in favor of meningioma, and the patient underwent complete resection of the dural-based lesion. Final pathology confirmed the unexpected finding of a metastatic prostate adenocarcinoma. Although he tolerated surgery well, the patient was subsequently referred for palliative therapy given findings of widespread systemic disease. Discussion Intracranial metastases may involve the dura, at times presenting with rare radiographic features highly suggestive for meningioma, as in our case here. This makes differentiation, at least based on imaging, a challenge. Elderly patients presenting with neurological deficits secondary to a newly-diagnosed, dural-based lesion should thus be considered for metastasis, prompting additional imaging studies (including body CT, MRI or PET) to rule out a primary lesion elsewhere. In some cases, this may affect the overall decision to proceed with surgical resection, or alternatively, to proceed directly to palliative therapy (the latter decision made in the context of widespread metastatic disease). Conclusion We conclude that dural-based metastatic lesions may mimic meningiomas, warranting thorough pre-operative work-up to exclude the possibility of metastasis. In certain cases, identification of widespread disease might preclude surgery and favor palliation, instead. PMID:26318129

Occupational factors and pancreatic cancer.

PubMed Central

Norell, S; Ahlbom, A; Olin, R; Erwald, R; Jacobson, G; Lindberg-Navier, I; Wiechel, K L

1986-01-01

The relation between occupational factors and pancreatic cancer has been studied by two different approaches: a population based case-control study with two series of controls and a retrospective cohort study based on register data. With both approaches, some support was found for an association with occupational exposure to petroleum products. Associations were also indicated with exposure to paint thinner (case-control study) and work in painting and in paint and varnish factories (cohort study), for exposure to detergents, floor cleaning agents, or polish (case-control study) and with floor polishing or window cleaning (cohort study), and for exposure to refuse (case-control study) and work in refuse disposal plants (cohort study). PMID:3790458

Work-hour restrictions and orthopaedic resident education: a systematic review.

PubMed

Mauser, Nathan S; Michelson, James D; Gissel, Hannah; Henderson, Corey; Mauffrey, Cyril

2016-05-01

The ACGME (US) and The European Working Time Directive (UK) placed work-hour restrictions on medical trainees with the goal of improved patient safety. However, there has been concern over a potential decrease in medical education. Orthopaedic training is the focus of this study. We examined previously published subjective and objective data regarding education and work-hour restrictions and developed the questions: Do specific perceptions emerge within the subjective studies examined? Are there objective differences in educational measures before and after work-hour restrictions? Is there a difference between the subjective and objective data? A systematic review was conducted via MedLine, regarding orthopaedic studies in the USA and UK, with reference to work-hour restrictions and education. Subjective survey studies demonstrate that residents and attending physicians have a negative response to work-hour restrictions because of the perceived impact on their overall education and operating room experience. Conversely, limited objective studies demonstrated no change in operative volume before or after implementation of restrictions. This review highlights the need for more objective studies on the educational implications of work-hour restrictions. Studies to date have not demonstrated a measurable difference based on case logs or training scores. Opinion-based surveys demonstrate an overall negative perception by both residents and attending physicians, on the impact of work-hour restrictions on orthopaedic education. Current published data is limited and stronger evidence-based data are needed before definitive conclusions can be reached.

Multivariate exploration of non-intrusive load monitoring via spatiotemporal pattern network

DOE PAGES

Liu, Chao; Akintayo, Adedotun; Jiang, Zhanhong; ...

2017-12-18

Non-intrusive load monitoring (NILM) of electrical demand for the purpose of identifying load components has thus far mostly been studied using univariate data, e.g., using only whole building electricity consumption time series to identify a certain type of end-use such as lighting load. However, using additional variables in the form of multivariate time series data may provide more information in terms of extracting distinguishable features in the context of energy disaggregation. In this work, a novel probabilistic graphical modeling approach, namely the spatiotemporal pattern network (STPN) is proposed for energy disaggregation using multivariate time-series data. The STPN framework is shownmore » to be capable of handling diverse types of multivariate time-series to improve the energy disaggregation performance. The technique outperforms the state of the art factorial hidden Markov models (FHMM) and combinatorial optimization (CO) techniques in multiple real-life test cases. Furthermore, based on two homes' aggregate electric consumption data, a similarity metric is defined for the energy disaggregation of one home using a trained model based on the other home (i.e., out-of-sample case). The proposed similarity metric allows us to enhance scalability via learning supervised models for a few homes and deploying such models to many other similar but unmodeled homes with significantly high disaggregation accuracy.« less

Multivariate exploration of non-intrusive load monitoring via spatiotemporal pattern network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chao; Akintayo, Adedotun; Jiang, Zhanhong

Non-intrusive load monitoring (NILM) of electrical demand for the purpose of identifying load components has thus far mostly been studied using univariate data, e.g., using only whole building electricity consumption time series to identify a certain type of end-use such as lighting load. However, using additional variables in the form of multivariate time series data may provide more information in terms of extracting distinguishable features in the context of energy disaggregation. In this work, a novel probabilistic graphical modeling approach, namely the spatiotemporal pattern network (STPN) is proposed for energy disaggregation using multivariate time-series data. The STPN framework is shownmore » to be capable of handling diverse types of multivariate time-series to improve the energy disaggregation performance. The technique outperforms the state of the art factorial hidden Markov models (FHMM) and combinatorial optimization (CO) techniques in multiple real-life test cases. Furthermore, based on two homes' aggregate electric consumption data, a similarity metric is defined for the energy disaggregation of one home using a trained model based on the other home (i.e., out-of-sample case). The proposed similarity metric allows us to enhance scalability via learning supervised models for a few homes and deploying such models to many other similar but unmodeled homes with significantly high disaggregation accuracy.« less

Dynamic and Thermal Turbulent Time Scale Modelling for Homogeneous Shear Flows

NASA Technical Reports Server (NTRS)

Schwab, John R.; Lakshminarayana, Budugur

1994-01-01

A new turbulence model, based upon dynamic and thermal turbulent time scale transport equations, is developed and applied to homogeneous shear flows with constant velocity and temperature gradients. The new model comprises transport equations for k, the turbulent kinetic energy; tau, the dynamic time scale; k(sub theta), the fluctuating temperature variance; and tau(sub theta), the thermal time scale. It offers conceptually parallel modeling of the dynamic and thermal turbulence at the two equation level, and eliminates the customary prescription of an empirical turbulent Prandtl number, Pr(sub t), thus permitting a more generalized prediction capability for turbulent heat transfer in complex flows and geometries. The new model also incorporates constitutive relations, based upon invariant theory, that allow the effects of nonequilibrium to modify the primary coefficients for the turbulent shear stress and heat flux. Predictions of the new model, along with those from two other similar models, are compared with experimental data for decaying homogeneous dynamic and thermal turbulence, homogeneous turbulence with constant temperature gradient, and homogeneous turbulence with constant temperature gradient and constant velocity gradient. The new model offers improvement in agreement with the data for most cases considered in this work, although it was no better than the other models for several cases where all the models performed poorly.

29 CFR 553.221 - Compensable hours of work.

Code of Federal Regulations, 2010 CFR

2010-07-01

... time (§ 553.222) apply to both law enforcement and firefighting employees for whom the section 7(k) exemption is claimed. Also, special rules for meal time apply in the case of firefighters (§ 553.223). Part... relief, and work performed on an occasional or sporadic and part-time basis, all of which are covered in...

COLLABORATE©: a universal competency-based paradigm for professional case management, part i: introduction, historical validation, and competency presentation.

PubMed

Treiger, Teresa M; Fink-Samnick, Ellen

2013-01-01

The purpose of this first of a three-article series is to provide context and justification for a new paradigm of case management built upon a value-driven foundation that Applicable to all health care sectors where case management is practiced. In moving forward, the one fact that rings true is there will be constant change in our industry. As the health care terrain shifts and new influences continually surface, there will be consequences for case management practice. These impacts require nimble clinical professionals in possession of recognized and firmly established competencies. They must be agile to frame (and reframe) their professional practice to facilitate the best possible outcomes for their patients. Case managers can choose to be Gumby or Pokey. This is exactly why the definition of a competency-based case management model's time has come, one sufficiently fluid to fit into any setting of care. The practice of case management transcends the vast array of representative professional disciplines and educational levels. A majority of current models are driven by business priorities rather than by the competencies critical to successful practice and quality patient outcomes. This results in a fragmented professional case management identity. While there is inherent value in what each discipline brings to the table, this advanced model unifies behind case management's unique, strengths-based identity instead of continuing to align within traditional divisions (e.g., discipline, work setting, population served). This model fosters case management's expanding career advancement opportunities, including a reflective clinical ladder.

Probabilistic seismic history matching using binary images

NASA Astrophysics Data System (ADS)

Davolio, Alessandra; Schiozer, Denis Jose

2018-02-01

Currently, the goal of history-matching procedures is not only to provide a model matching any observed data but also to generate multiple matched models to properly handle uncertainties. One such approach is a probabilistic history-matching methodology based on the discrete Latin Hypercube sampling algorithm, proposed in previous works, which was particularly efficient for matching well data (production rates and pressure). 4D seismic (4DS) data have been increasingly included into history-matching procedures. A key issue in seismic history matching (SHM) is to transfer data into a common domain: impedance, amplitude or pressure, and saturation. In any case, seismic inversions and/or modeling are required, which can be time consuming. An alternative to avoid these procedures is using binary images in SHM as they allow the shape, rather than the physical values, of observed anomalies to be matched. This work presents the incorporation of binary images in SHM within the aforementioned probabilistic history matching. The application was performed with real data from a segment of the Norne benchmark case that presents strong 4D anomalies, including softening signals due to pressure build up. The binary images are used to match the pressurized zones observed in time-lapse data. Three history matchings were conducted using: only well data, well and 4DS data, and only 4DS. The methodology is very flexible and successfully utilized the addition of binary images for seismic objective functions. Results proved the good convergence of the method in few iterations for all three cases. The matched models of the first two cases provided the best results, with similar well matching quality. The second case provided models presenting pore pressure changes according to the expected dynamic behavior (pressurized zones) observed on 4DS data. The use of binary images in SHM is relatively new with few examples in the literature. This work enriches this discussion by presenting a new application to match pressure in a reservoir segment with complex pressure behavior.

Recovering Process from Child Sexual Abuse During Adulthood from an Integrative Approach to Solution-Focused Therapy: A Case Study.

PubMed

Gonzalez, Carolina

2017-10-01

In recent times, strengths-based recovery approaches that focus on the present and build strategies that look toward the future have become popular. However, some cases require the consideration of experiences from previous stages of the clients' development. This single-case study explores the psychotherapeutic process of a middle-aged woman who presented with a history of child sexual abuse (incest) and a long-term adult diagnosis of depression that was treated in public health services. This psychotherapy involved an integrative approach to solution-focused therapy; specifically, the approach proposed by Yvonne Dolan to work with adult survivors of sexual abuse, in conjunction with techniques and strategies from the transtheoretical model. Measures incorporating therapeutic working alliance and outcomes were administered over sessions. Results showed positive outcomes from this therapeutic intervention, which remained at 3-month and 12-month follow-ups. Implications for practitioners' specialist practice in health services are discussed, given the complexity of comorbid mental health conditions with a history of child sexual abuse.

Group Work in the MBA Classroom: Improving Pedagogical Practice and Maximizing Positive Outcomes with Part-Time MBA Students

ERIC Educational Resources Information Center

Rafferty, Patricia D.

2013-01-01

This article forms part of an exploration into how graduate students experience group work. A single case, embedded study was completed in 2011, which reveals insight and understanding into the manner in which part-time MBA students experience group work assignments and how these experiences contribute to their perception of positive group work…

Unilateral contact induced blade/casing vibratory interactions in impellers: Analysis for rigid casings

NASA Astrophysics Data System (ADS)

Batailly, Alain; Meingast, Markus; Legrand, Mathias

2015-02-01

This contribution addresses the vibratory analysis of unilateral-contact induced structural interactions between a bladed impeller and its surrounding rigid casing. Such assemblies can be found in helicopter or small aircraft engines for instance and the interactions of interest shall arise due to the always tighter operating clearances between the rotating and stationary components. The investigation is conducted by extending to cyclically symmetric structures an in-house time-marching based tool dedicated to unilateral contact occurrences in turbomachines. The main components of the considered impeller together with the associated assumptions and modelling principles considered in this work are detailed. Typical dynamical features of cyclically symmetric structures, such as the aliasing effect and frequency clustering are explored in this nonlinear framework by means of thorough frequency-domain analyses and harmonic trackings of the numerically predicted impeller displacements. Additional contact maps highlight the existence of critical rotational velocities at which displacements potentially reach high amplitudes due to the synchronization of the bladed assembly vibratory pattern with the shape of the rigid casing. The proposed numerical investigations are also compared to a simpler and (almost) empirical criterion: it is suggested, based on nonlinear numerical simulations with a linear reduced order model of the impeller and a rigid casing, that this criterion may miss important critical velocities emanating from the unfavorable combination of aliasing and contact-induced higher harmonics in the vibratory response of the impeller. Overall, this work suggests a way to enhance guidelines to improve the design of impellers in the context of nonlinear and nonsmooth dynamics.

[Development of pneumoconiosis and outsourcing work in peruvian miners].

PubMed

Cáceres-Mejía, Brenda; Mayta-Tristán, Percy; Pereyra-Elías, Reneé; Collantes, Héctor; Cáceres-Leturia, Walter

2015-10-01

The aim of this study is to evaluate the association between the time of outsourced work and the development of pneumoconiosis in Peruvian miners who attended the "Centro Nacional de Salud Ocupacional y Protección al Ambiente para la Salud" between 2008 and 2011. Retrospective case-control study. Cases were defined as workers diagnosed of pneumoconiosis under standardized criteria. Outsourced work was defined as the time (in months) of work in a company that does not own the primary mining project. The project owner company was registered in the Mining Companies Directory (Ministerio de Energía y Minas). We used multiple logistic regression with crude and adjusted ORs. The study comprised 391 cases and 1519 controls. In both groups, most of the study subjects had a level of education lower than complete high school and were born and currently lived in the Peruvian highlands. There was statistically significant association between more frequency of pneumoconiosis and working 10 or more years in an outsourced company (OR: 1.50; 95%CI: 1.05-1.14; p=0.026). Miners with pneumoconiosis were more likely not to have education (OR: 3.07; 95%CI: 1.55-6.08; p=0.001), be currently living at the Peruvian highlands (OR: 1.40; 95%CI: 1.10-1.78; p=0.007) and to have more than 20 years of underground work history (OR: 8.92; 95%CI: 4.53-18.25; p<0.001). A statistically significant association was found between pneumoconiosis and the time of outsourced work. Not having education, residing in the Peruvian highlands and the time of underground work were associated risk factors.

Vocational training courses as an intervention on change of work practice among immigrant cleaners.

PubMed

Jensen, Flemming W; Frydendall, Karen B; Flyvholm, Mari-Ann

2011-11-01

The aim of the study was to examine how knowledge and skills from vocational training courses on working techniques modified for immigrant cleaners are applied in practice and to identify factors that influence the implementation. The modifications of the standard course included language support with possibilities for translation and an extension of the duration of the course. The study is a prospective intervention study based on qualitative data. Data were collected as structured interviews and observations were carried out at the workplaces before and after the course. The study population included 31 immigrant cleaners from five different workplaces. Changes were observed in the use of working techniques (i.e., positioning of hands when using the floor mop). In some cases the use of the taught techniques was incorrect, partial, or only used part of the time. Interactions between individual factors (i.e., knowledge, awareness, capability, or work orientation) and environmental factors (i.e., equipment, time, workload, or physical surroundings) influenced the use of the techniques in practice. The course provided the participants with new working techniques through which some were able to reduce work related pain. However, with regard to incorrect and partial use of the working techniques, follow-up and post-training support is recommended. Copyright © 2011 Wiley Periodicals, Inc.

Performance assessment and beamline diagnostics based on evaluation of temporal information from infrared spectral datasets by means of R Environment for statistical analysis.

PubMed

Banas, Krzysztof; Banas, Agnieszka; Gajda, Mariusz; Kwiatek, Wojciech M; Pawlicki, Bohdan; Breese, Mark B H

2014-07-15

Assessment of the performance and up-to-date diagnostics of scientific equipment is one of the key components in contemporary laboratories. Most reliable checks are performed by real test experiments while varying the experimental conditions (typically, in the case of infrared spectroscopic measurements, the size of the beam aperture, the duration of the experiment, the spectral range, the scanner velocity, etc.). On the other hand, the stability of the instrument response in time is another key element of the great value. Source stability (or easy predictable temporal changes, similar to those observed in the case of synchrotron radiation-based sources working in non top-up mode), detector stability (especially in the case of liquid nitrogen- or liquid helium-cooled detectors) should be monitored. In these cases, recorded datasets (spectra) include additional variables such as time stamp when a particular spectrum was recorded (in the case of time trial experiments). A favorable approach in evaluating these data is building hyperspectral object that consist of all spectra and all additional parameters at which these spectra were recorded. Taking into account that these datasets could be considerably large in size, there is a need for the tools for semiautomatic data evaluation and information extraction. A comprehensive R archive network--the open-source R Environment--with its flexibility and growing potential, fits these requirements nicely. In this paper, examples of practical implementation of methods available in R for real-life Fourier transform infrared (FTIR) spectroscopic data problems are presented. However, this approach could easily be adopted to many various laboratory scenarios with other spectroscopic techniques.

Model-Based IN SITU Parameter Estimation of Ultrasonic Guided Waves in AN Isotropic Plate

NASA Astrophysics Data System (ADS)

Hall, James S.; Michaels, Jennifer E.

2010-02-01

Most ultrasonic systems employing guided waves for flaw detection require information such as dispersion curves, transducer locations, and expected propagation loss. Degraded system performance may result if assumed parameter values do not accurately reflect the actual environment. By characterizing the propagating environment in situ at the time of test, potentially erroneous a priori estimates are avoided and performance of ultrasonic guided wave systems can be improved. A four-part model-based algorithm is described in the context of previous work that estimates model parameters whereby an assumed propagation model is used to describe the received signals. This approach builds upon previous work by demonstrating the ability to estimate parameters for the case of single mode propagation. Performance is demonstrated on signals obtained from theoretical dispersion curves, finite element modeling, and experimental data.

Differences in day and night shift clinical performance in anesthesiology.

PubMed

Cao, Caroline G L; Weinger, Matthew B; Slagle, Jason; Zhou, Chuan; Ou, Jennie; Gillin, Shakha; Sheh, Bryant; Mazzei, William

2008-04-01

This study examined whether anesthesia residents (physicians in training) performed clinical duties in the operating room differently during the day versus at night. Fatigue from sleep deprivation and working through the night is common for physicians, particularly during residency training. Using a repeated-measures design, we studied 13 pairs of day-night matched anesthesia cases. Dependent measures included task times, workload ratings, response to an alarm light latency task, and mood. Residents spent significantly less time on manual tasks and more time on monitoring tasks during the maintenance phase at night than during the day. Residents reported more negative mood at night than during the day, both pre- and postoperation. However, time of day had no effect on the mood change between pre- and postoperation. Workload ratings and the response time to an alarm light latency task were not significantly different between night and day cases. Because night shift residents had been awake and working for more than 16 hr, the observed differences in task performance and mood may be attributed to fatigue. The changes in task distribution during night shift work may represent compensatory strategies to maintain patient care quality while keeping perceived workload at a manageable level. Fatigue effects during night shifts should be considered when designing work-rest schedules for clinicians. This matched-case control scheme can also be applied to study other phenomena associated with patient safety in the actual clinical environment.

Risk Factors Analysis and Death Prediction in Some Life-Threatening Ailments Using Chi-Square Case-Based Reasoning (χ2 CBR) Model.

PubMed

Adeniyi, D A; Wei, Z; Yang, Y

2018-01-30

A wealth of data are available within the health care system, however, effective analysis tools for exploring the hidden patterns in these datasets are lacking. To alleviate this limitation, this paper proposes a simple but promising hybrid predictive model by suitably combining the Chi-square distance measurement with case-based reasoning technique. The study presents the realization of an automated risk calculator and death prediction in some life-threatening ailments using Chi-square case-based reasoning (χ 2 CBR) model. The proposed predictive engine is capable of reducing runtime and speeds up execution process through the use of critical χ 2 distribution value. This work also showcases the development of a novel feature selection method referred to as frequent item based rule (FIBR) method. This FIBR method is used for selecting the best feature for the proposed χ 2 CBR model at the preprocessing stage of the predictive procedures. The implementation of the proposed risk calculator is achieved through the use of an in-house developed PHP program experimented with XAMP/Apache HTTP server as hosting server. The process of data acquisition and case-based development is implemented using the MySQL application. Performance comparison between our system, the NBY, the ED-KNN, the ANN, the SVM, the Random Forest and the traditional CBR techniques shows that the quality of predictions produced by our system outperformed the baseline methods studied. The result of our experiment shows that the precision rate and predictive quality of our system in most cases are equal to or greater than 70%. Our result also shows that the proposed system executes faster than the baseline methods studied. Therefore, the proposed risk calculator is capable of providing useful, consistent, faster, accurate and efficient risk level prediction to both the patients and the physicians at any time, online and on a real-time basis.

A simplified technique of orthograde MTA obturation on the elected canals of posterior teeth: Two case reports.

PubMed

Wahengbam, Brucelee; Wahengbam, Pragya; Tikku, Aseem Prakash

2014-01-01

This article suggests a simplified technique of orthograde MTA obturation in less accessible canal(s) of posteriors teeth without using costly ultrasonics or specialised carrier. Essentially few finger pluggers, absorbent points and a simple canal projection method were used. The orifice(s) of the elected canal(s) to be obturated with MTA were projected onto the external occlusal surface for easy delivery and predictive instrumentation. The idea was based on 'easy access', 'working one canal with one mix at one time', 'thorough condensation' and 'removal of excess moisture'. In case I, palatal canal of tooth no. 2 with gross apical perforation and suspected VRF was obturated with MTA. And in Case II, tooth no. 19 presented with incomplete furcal fracture extending into the canal was obturated with MTA in all 3 canals unitarily. Dense homogenous MTA obturation was achieved and both cases healed uneventfully.

Work, Productivity, and Human Performance: Practical Case Studies in Ergonomics, Human Factors and Human Engineering.

ERIC Educational Resources Information Center

Fraser, T. M.; Pityn, P. J.

This book contains 12 case histories, each based on a real-life problem, that show how a manager can use common sense, knowledge, and interpersonal skills to solve problems in human performance at work. Each case study describes a worker's problem and provides background information and an assignment; solutions are suggested. The following cases…

Energy-based operator splitting approach for the time discretization of coupled systems of partial and ordinary differential equations for fluid flows: The Stokes case

NASA Astrophysics Data System (ADS)

Carichino, Lucia; Guidoboni, Giovanna; Szopos, Marcela

2018-07-01

The goal of this work is to develop a novel splitting approach for the numerical solution of multiscale problems involving the coupling between Stokes equations and ODE systems, as often encountered in blood flow modeling applications. The proposed algorithm is based on a semi-discretization in time based on operator splitting, whose design is guided by the rationale of ensuring that the physical energy balance is maintained at the discrete level. As a result, unconditional stability with respect to the time step choice is ensured by the implicit treatment of interface conditions within the Stokes substeps, whereas the coupling between Stokes and ODE substeps is enforced via appropriate initial conditions for each substep. Notably, unconditional stability is attained without the need of subiterating between Stokes and ODE substeps. Stability and convergence properties of the proposed algorithm are tested on three specific examples for which analytical solutions are derived.

Shining X-rays on catalysts at work

NASA Astrophysics Data System (ADS)

Grunwaldt, J.-D.

2009-11-01

Structure-performance relationships gained by studying catalysts at work are considered the key to further development of catalysts underlined here by a brief overview on our research in this area. The partial oxidation of methane to hydrogen and carbon monoxide over Pt- and Rh-based catalysts and the total combustion of hydrocarbons demonstrate the importance of structural identification of catalysts in its working state and the measurement of the catalytic performance at the same time. Moreover, proper cell design is a key both here and in liquid phase reactions including preparation or high pressure reactions. In several cases structural changes during preparation, activation and reaction occur on a subminute scale or the catalyst structure varies inside a reactor as a result of temperature or concentration gradients. This, additionally, requires time and spatial resolution. Examples from time-resolved QEXAFS studies during the partial oxidation of methane over Pt- and Rh-based catalysts demonstrate some of the recent developments of the technique (use not only of Si(111) but also Si(311) crystals, angular encoder, full EXAFS spectra at subsecond recording time, and modulation excitation spectroscopy). In order to obtain spectroscopic information on the oxidation state inside a microreactor, scanning and full field X-ray microscopy with X-ray absorption spectroscopic contrast were achieved under reaction conditions. If a microbeam is applied, fast scanning techniques like QEXAFS are required. In this way, even X-ray absorption spectroscopic tomographic images of a slice of a microreactor were obtained. The studies were recently extended to spatiotemporal studies that give important insight into the dynamics of the catalyst structure in a spatial manner with subsecond time-resolution.

Occupational back disability in U.S. Army personnel.

PubMed

Berkowitz, S M; Feuerstein, M; Lopez, M S; Peck, C A

1999-06-01

Musculoskeletal disorders represent a prevalent source of outpatient visits, lost work time, hospitalization, and disability in the military. Recent research has identified patterns among military occupations, gender, and musculoskeletal disability. Although back disorders accounted for a high percentage of all cases, little is known about the relationship between job type and disability in soldiers. The present study analyzed 41,750 disability cases to determine (1) prevalence of work-related back disability diagnoses, (2) specific jobs associated with greater risk of back disability, and (3) association among gender, job type, and disability. The results indicate that (1) lumbosacral strain and intervertebral disc syndrome represent the most prevalent diagnoses for back disability, (2) certain occupations were associated with higher back disability risk, and (3) specific jobs were identified in which females experienced higher rates of back disability than males. The nature of these high-risk jobs, and recent research on work disability factors in U.S. Army soldiers, suggest that a combination of ergonomic and individual/organizational psychosocial factors may play a role in the development, exacerbation, and maintenance of work disability. Future research that identifies specific job factors contributing to increased back disability risk should assist in the development of empirically based work site prevention programs to improve musculoskeletal health and readiness.

Learning curve of single port laparoscopic cholecystectomy determined using the non-linear ordinary least squares method based on a non-linear regression model: An analysis of 150 consecutive patients.

PubMed

Han, Hyung Joon; Choi, Sae Byeol; Park, Man Sik; Lee, Jin Suk; Kim, Wan Bae; Song, Tae Jin; Choi, Sang Yong

2011-07-01

Single port laparoscopic surgery has come to the forefront of minimally invasive surgery. For those familiar with conventional techniques, however, this type of operation demands a different type of eye/hand coordination and involves unfamiliar working instruments. Herein, the authors describe the learning curve and the clinical outcomes of single port laparoscopic cholecystectomy for 150 consecutive patients with benign gallbladder disease. All patients underwent single port laparoscopic cholecystectomy using a homemade glove port by one of five operators with different levels of experiences of laparoscopic surgery. The learning curve for each operator was fitted using the non-linear ordinary least squares method based on a non-linear regression model. Mean operating time was 77.6 ± 28.5 min. Fourteen patients (6.0%) were converted to conventional laparoscopic cholecystectomy. Complications occurred in 15 patients (10.0%), as follows: bile duct injury (n = 2), surgical site infection (n = 8), seroma (n = 2), and wound pain (n = 3). One operator achieved a learning curve plateau at 61.4 min per procedure after 8.5 cases and his time improved by 95.3 min as compared with initial operation time. Younger surgeons showed significant decreases in mean operation time and achieved stable mean operation times. In particular, younger surgeons showed significant decreases in operation times after 20 cases. Experienced laparoscopic surgeons can safely perform single port laparoscopic cholecystectomy using conventional or angled laparoscopic instruments. The present study shows that an operator can overcome the single port laparoscopic cholecystectomy learning curve in about eight cases.

Talking Physics: Two Case Studies on Short Answers and Self-explanation in Learning Physics

NASA Astrophysics Data System (ADS)

Badeau, Ryan C.

This thesis explores two case studies into the use of short answers and self-explanation to improve student learning in physics. The first set of experiments focuses on the role of short answer questions in the context of computer-based instruction. Through a series of six experiments, we compare and evaluate the performance of computer-assessed short answer questions versus multiple choice for training conceptual topics in physics, controlling for feedback between the two formats. In addition to finding overall similar improvements on subsequent student performance and retention, we identify unique differences in how students interact with the treatments in terms of time spent on feedback and performance on follow-up short answer assessment. In addition, we identify interactions between the level of interactivity of the training, question format, and student attitudinal ratings of each respective training. The second case study focuses on the use of worked examples in the context of multi-concept physics problems - which we call "synthesis problems." For this part of the thesis, four experiments were designed to evaluate the effectiveness of two instructional methods employing worked examples on student performance with synthesis problems; these instructional techniques, analogical comparison and self-explanation, have previously been studied primarily in the context of single-concept problems. As such, the work presented here represents a novel focus on extending these two techniques to this class of more complicated physics problem. Across the four experiments, both self-explanation and certain kinds of analogical comparison of worked examples significantly improved student performance on a target synthesis problem, with distinct improvements in recognition of the relevant concepts. More specifically, analogical comparison significantly improved student performance when the comparisons were invoked between worked synthesis examples. In contrast, similar comparisons between corresponding pairs of worked single-concept examples did not significantly improve performance. On a more complicated synthesis problem, self-explanation was significantly more effective than analogical comparison, potentially due to differences in how successfully students encoded the full structure of the worked examples. Finally, we find that the two techniques can be combined for additional benefit, with the trade-off of slightly more time-on-task.

Interdisciplinary Data Fusion for Diachronic 3d Reconstruction of Historic Sites

NASA Astrophysics Data System (ADS)

Micoli, L. L.; Gonizzi Barsanti, S.; Guidi, G.

2017-02-01

In recent decades, 3D reconstruction has progressively become a tool to show archaeological and architectural monuments in their current state, presumed past aspect and to predict their future evolution. The 3D representations trough time can be useful in order to study and preserve the memory of Cultural Heritage and to plan maintenance and promotion of the historical sites. This paper represent a case study, at architectonic and urbanistic scale, based on methodological approach for CH time-varying representations proposed by JPI-CH European Project called Cultural Heritage Through Time (CHT2). The work is focused on the area of Milan Roman circus, relatively to which was conducted both a thorough philological research based on several sources and a 3D survey campaign of still accessible remains, aiming at obtaining the monumental representation of the area in 3 different ages.

Outdoor Light at Night and Breast Cancer Incidence in the Nurses’ Health Study II

PubMed Central

Bertrand, Kimberly A.; Hart, Jaime E.; Schernhammer, Eva S.; Tamimi, Rulla M.; Laden, Francine

2017-01-01

Background: Animal and epidemiologic studies suggest that exposure to light at night (LAN) may disrupt circadian patterns and decrease nocturnal secretion of melatonin, which may disturb estrogen regulation, leading to increased breast cancer risk. Objectives: We examined the association between residential outdoor LAN and breast cancer incidence using data from the nationwide U.S.-based Nurses’ Health Study II cohort. Methods: We followed 109,672 women from 1989 through 2013. Cumulative LAN exposure was estimated using time-varying satellite data for a composite of persistent nighttime illumination at ∼1 km2 scale for each residence during follow-up. Incident invasive breast cancer cases were confirmed by medical record review. We used Cox proportional hazard models to calculate hazard ratios (HRs) and 95% confidence intervals (CIs), adjusting for anthropometric, reproductive, lifestyle, and socioeconomic risk factors. Results: Over 2,187,425 person-years, we identified 3,549 incident breast cancer cases. Based on a fully adjusted model, the estimated HR for incident breast cancer with an interquartile range (IQR) (31.6 nW/cm2/sr) increase in cumulative average outdoor LAN was 1.05 (95% CI: 1.00, 1.11). An association between LAN and breast cancer appeared to be limited to women who were premenopausal at the time of a case [HR=1.07 (95% CI: 1.01, 1.14) based on 1,973 cases vs. HR=1.00 (95% CI: 0.91, 1.09) based on 1,172 cases in postmenopausal women; p-interaction=0.08]. The LAN–breast cancer association was observed only in past and current smokers at the end of follow-up [HR=1.00 (95% CI: 0.94, 1.07) based on 2,215 cases in never smokers; HR=1.10 (95% CI: 1.01, 1.19) based on 1,034 cases in past smokers vs. HR=1.21 (95% CI: 1.07, 1.37) for 300 cases in current smokers; p-interaction=0.08]. Conclusions: Although further work is required to confirm our results and to clarify potential mechanisms, our findings suggest that exposure to residential outdoor light at night may contribute to invasive breast cancer risk. https://doi.org/10.1289/EHP935 PMID:28886600

TH-A-19A-11: Validation of GPU-Based Monte Carlo Code (gPMC) Versus Fully Implemented Monte Carlo Code (TOPAS) for Proton Radiation Therapy: Clinical Cases Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giantsoudi, D; Schuemann, J; Dowdell, S

Purpose: For proton radiation therapy, Monte Carlo simulation (MCS) methods are recognized as the gold-standard dose calculation approach. Although previously unrealistic due to limitations in available computing power, GPU-based applications allow MCS of proton treatment fields to be performed in routine clinical use, on time scales comparable to that of conventional pencil-beam algorithms. This study focuses on validating the results of our GPU-based code (gPMC) versus fully implemented proton therapy based MCS code (TOPAS) for clinical patient cases. Methods: Two treatment sites were selected to provide clinical cases for this study: head-and-neck cases due to anatomical geometrical complexity (air cavitiesmore » and density heterogeneities), making dose calculation very challenging, and prostate cases due to higher proton energies used and close proximity of the treatment target to sensitive organs at risk. Both gPMC and TOPAS methods were used to calculate 3-dimensional dose distributions for all patients in this study. Comparisons were performed based on target coverage indices (mean dose, V90 and D90) and gamma index distributions for 2% of the prescription dose and 2mm. Results: For seven out of eight studied cases, mean target dose, V90 and D90 differed less than 2% between TOPAS and gPMC dose distributions. Gamma index analysis for all prostate patients resulted in passing rate of more than 99% of voxels in the target. Four out of five head-neck-cases showed passing rate of gamma index for the target of more than 99%, the fifth having a gamma index passing rate of 93%. Conclusion: Our current work showed excellent agreement between our GPU-based MCS code and fully implemented proton therapy based MC code for a group of dosimetrically challenging patient cases.« less

Guiding science expeditions: The design of a learning environment for project-based science

NASA Astrophysics Data System (ADS)

Polman, Joseph Louis

Project-based pedagogy has been revived recently as a teaching strategy for promoting students' active engagement in learning science by doing science. Numerous reform efforts have encouraged project-based teaching in high schools, along with a range of supports for its implementation, often including computers and the Internet. History has shown, however, that academic research and new technologies are not enough to effect real change in classrooms. Ultimately, teachers accomplish activity with their students daily in classrooms. Putting the idea of project-based teaching into practice depends on many particulars of teachers' situated work with students. To better understand the complexity of project-based science teaching in schools, I conducted an interpretive case study of one exceptional teacher's work. The teacher devotes all class time after the beginning of the year to open-ended, student-designed Earth Science research projects. Over four years of involvement with the Learning through Collaborative Visualization (CoVis) reform effort, this teacher has developed, implemented, and refined strategies for supporting and guiding students in conducting open-ended inquiry. Through a close examination of the teacher's work supporting student projects, I explore the design issues involved in such an endeavor, including affordances, constraints, and tradeoffs. In particular, I show how time constrains both student and teacher action, how the traditional school culture and grading create stumbling blocks for change, and how conflicting beliefs about teaching and learning undermine the accomplishment of guided inquiry. I also show how Internet tools including Usenet news, email, and the World Wide Web afford students an opportunity to gather and make use of distributed expertise and scientific data resources; how an activity structure, combined with a corresponding structure to the artifact of the final written product, supports student accomplishment of unfamiliar practices; and how the teacher guides students in real time through mutually transformative communication. I synthesize the important design elements into a framework for conducting project-based science, especially in settings where such pedagogy is relatively new. This study will inform teachers and reformers of the practical and complex work of implementing project-based teaching in schools.

Simulations of the vortex in the Dellenback abrupt expansion, resembling a hydro turbine draft tube operating at part-load

NASA Astrophysics Data System (ADS)

Nilsson, H.

2012-11-01

This work presents an OpenFOAM case-study, based on the experimental studies of the swirling flow in the abrupt expansion by Dellenback et al.[1]. The case yields similar flow conditions as those of a helical vortex rope in a hydro turbine draft tube working at part-load. The case-study is set up similar to the ERCOFTAC Conical Diffuser and Centrifugal Pump OpenFOAM case-studies [2,3], making all the files available and the results fully reproducable using OpenSource software. The mesh generation is done using m4 scripting and the OpenFOAM built-in blockMesh mesh generator. The swirling inlet boundary condition is specified as an axi-symmetric profile. The outlet boundary condition uses the zeroGradient condition for all variables except for the pressure, which uses the fixed mean value boundary condition. The wall static pressure is probed at a number of locations during the simulations, and post-processing of the time-averaged solution is done using the OpenFOAM sample utility. Gnuplot scripts are provided for plotting the results. The computational results are compared to one of the operating conditions studied by Dellenback, and measurements for all the experimentally studied operating conditions are available in the case-study. Results from five cases are here presented, based on the kEpsilon model, the kOmegaSST model, and a filtered version of the same kOmegaSST model, named kOmegaSSTF [4,5]. Two different inlet boundary conditions are evaluated. It is shown that kEpsilon and kOmegaSST give steady solutions, while kOmegaSSTF gives a highly unsteady solution. The time-averaged solution of the kOmegaSSTF model is much more accurate than the other models. The kEpsilon and kOmegaSST models are thus unable to accurately model the effect of the large-scale unsteadiness, while kOmegaSSTF resolves those scales and models only the smaller scales. The use of two different boundary conditions shows that the boundary conditions are more important than the choice between kEpsilon and kOmegaSST, for the results just after the abrupt expansion.

Safety Case Notations: Alternatives for the Non-Graphically Inclined?

NASA Technical Reports Server (NTRS)

Holloway, C. M.

2008-01-01

This working paper presents preliminary ideas of five possible text-based notations for representing safety cases, which may be easier for non-graphically inclined people to use and understand than the currently popular graphics-based representations.

How do geological sampling biases affect studies of morphological evolution in deep time? A case study of pterosaur (Reptilia: Archosauria) disparity.

PubMed

Butler, Richard J; Brusatte, Stephen L; Andres, Brian; Benson, Roger B J

2012-01-01

A fundamental contribution of paleobiology to macroevolutionary theory has been the illumination of deep time patterns of diversification. However, recent work has suggested that taxonomic diversity counts taken from the fossil record may be strongly biased by uneven spatiotemporal sampling. Although morphological diversity (disparity) is also frequently used to examine evolutionary radiations, no empirical work has yet addressed how disparity might be affected by uneven fossil record sampling. Here, we use pterosaurs (Mesozoic flying reptiles) as an exemplar group to address this problem. We calculate multiple disparity metrics based upon a comprehensive anatomical dataset including a novel phylogenetic correction for missing data, statistically compare these metrics to four geological sampling proxies, and use multiple regression modeling to assess the importance of uneven sampling and exceptional fossil deposits (Lagerstätten). We find that range-based disparity metrics are strongly affected by uneven fossil record sampling, and should therefore be interpreted cautiously. The robustness of variance-based metrics to sample size and geological sampling suggests that they can be more confidently interpreted as reflecting true biological signals. In addition, our results highlight the problem of high levels of missing data for disparity analyses, indicating a pressing need for more theoretical and empirical work. © 2011 The Author(s). Evolution © 2011 The Society for the Study of Evolution.

Medium-density fibreboard and occupational asthma. A case series.

PubMed

Burton, C; Bradshaw, L; Agius, R; Burge, S; Huggins, V; Fishwick, D

2011-08-01

Medium-density fibreboard (MDF) is a wood composite material, composed primarily of softwood, bonded with a synthetic formaldehyde-based resin. It is increasingly used, as it has various advantages over natural woods. Enquiry of the national reporting scheme data and three case reports were used to further the evidence base linking this exposure to occupational asthma (OA). From 1991 to 2007, 21 cases of occupational sensitization to MDF were reported to the UK voluntary reporting scheme, Surveillance of Work Related Occupational Respiratory Disease (SWORD): 18 reported as occupational asthma (OA) and 3 as occupational rhinitis. All workers were male, with a mean age of 48 years, working in education, furniture manufacturing or joinery among other employments. Whilst reporting scheme data identified relatively small numbers of cases of OA likely to be due to MDF, the evidence base supporting this link is generally lacking. The three cases presented, where OA was attributed to MDF exposure, add to this evidence.

Role of survivor bias in pancreatic cancer case-control studies.

PubMed

Hu, Zhen-Huan; Connett, John E; Yuan, Jian-Min; Anderson, Kristin E

2016-01-01

The purpose of this study was to evaluate the impact of survivor bias on pancreatic cancer case-control studies. The authors constructed five case-loss scenarios based on the Iowa Women's Health Study cohort to reflect how case recruitment in population-based studies varies by case survival time. Risk factors for disease incidence included smoking, body mass index (BMI), waist circumference, diabetes, and alcohol consumption. Odds ratios (ORs) were estimated by conditional logistic regression and quantitatively compared by the interactions between risk factors and 3-month survival time. Additionally, Kaplan-Meier estimates for overall survival were compared within the subset cohort of pancreatic cancer cases. BMI and waist circumference showed a significant inverse relationship with survival time. Decreasing trends in ORs for BMI and waist circumference were observed with increasing case survival time. The interaction between BMI and survival time based on a cutpoint of 3 months was significant (P < .01) as was the interaction between waist circumference and survival time (P < .01). The findings suggested that case losses could result in survivor bias causing underestimated odds ratios for both BMI and waist circumference, whereas other risk factors were not significantly affected by case losses. Copyright © 2016 Elsevier Inc. All rights reserved.

Characterising Extrinsic Challenges Linked to the Design and Implementation of Inquiry-Based Practical Work

NASA Astrophysics Data System (ADS)

Akuma, Fru Vitalis; Callaghan, Ronel

2017-11-01

Inquiry-based science education has been incorporated in science curricula internationally. In this regard, however, many teachers encounter challenges. The challenges have been characterised into those linked to the personal characteristics of these teachers (intrinsic challenges) and others associated with contextual factors (extrinsic challenges). However, this level of characterisation is inadequate in terms of appreciating the complexity of the challenges, tracking of their development, and discovering knowledge within specific categories. Against this background, the purpose of the research presented here was to characterise extrinsic challenges linked to the design and implementation of inquiry-based practical work. In order to do so, we used a conceptual framework of teaching challenges based on Bronfenbrenner's ecological theory of human development. The data gathered using a multi-method case study of practical work in two South African high schools, was analysed by combining the data-driven inductive approach and the deductive a priori template of codes approach in thematic analysis. On this basis, the extrinsic challenges linked to the design and implementation of inquiry-based practical work that participants are confronted with, were found to consist of macrosystem challenges (such as a restrictive curriculum) and microsystem challenges. At the latter level, the challenges are material-related (e.g., lack of science education equipment and materials) or non-material-related (such as time constraints and the lack of access to interactive computer simulations). We have discussed the theory-, practice- and research-based implications of these results in relation to the design and implementation of inquiry-based practical work in South Africa and internationally.

Sustaining patient and public involvement in research: A case study of a research centre

PubMed Central

Jinks, Clare; Carter, Pam; Rhodes, Carol; Beech, Roger; Dziedzic, Krysia; Hughes, Rhian; Blackburn, Steven; Ong, Bie Nio

2013-01-01

The literature on patient and public involvement (PPI) in research covers a wide range of topics. However, one area of investigation that appears under developed is the sustainability and impact of PPI beyond involvement in time-limited research projects. This paper presents a case study of PPI development in one primary care research centre in England, and its approach to making this sustainable using documentary sources and material from a formal evaluation. We provide narrative accounts of the set-up, operation and main processes of PPI, and its perceived impact. PPI requires a long-term perspective with participation and trust growing over time, and both users and researchers learning what approaches work best. PPI is a complex interplay of clarity of purpose, defined roles and relationships, organised support (paid PPI staff) and a well-funded infrastructure. ‘Soft systems’ are equally important such as flexible and informal approaches to meetings, adapting timetables and environments to meet the needs of lay members and to create spaces for relationships to develop between researchers and lay members that are based on mutual trust and respect. This case study highlights that the right combination of ethos, flexible working practices, leadership, and secure funding goes a long way to embedding PPI beyond ad hoc involvement. This allows PPI in research to be integrated in the infrastructure and sustainable. PMID:26705412

Determinants of papillary cancer of the thyroid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wingren, G.; Hatschek, T.; Axelson, O.

1993-10-01

Determinants of papillary thyroid cancer were evaluated in a questionnaire-based case-control study from southeastern Sweden. A total of 104 cases, diagnosed from 1977 to 1987, and 387 randomly selected controls were included in the analyses. Female subjects with papillary cancer reported a work history as dentists/dental assistants, telephone operators, teachers, and day nursery personnel, and an occupational contact with chemicals and video display terminals more often than did controls. The 11 male cases more often reported working as mechanics and metal workers and having occupational contact with solvents. Other factors associated with increased risk for female papillary cancer were havingmore » private well water at the birth address; leisure time exposure to combustion smoke; low intake of cruciferous vegetables and seafood; and a family history of goiter, heart disease, biliary disorder, or female genital cancer. Diagnostic radiographic examinations, especially to the head, neck, or upper back/chest area, or repeated dental examinations, were also found to be associated with this form of cancer. With regard to the possible influence from hormonal factors among women less than age 50 years at time of diagnosis, an increased risk was found for a pregnancy soon after puberty. Tendencies toward a decreasing risk with increasing age at first pregnancy as well as an increasing risk with increasing number of pregnancies were found as well. Multiparity seemed to potentiate the effect from prior radiographic examinations.« less

Transverse parton distribution functions at next-to-next-to-leading order: the quark-to-quark case.

PubMed

Gehrmann, Thomas; Lübbert, Thomas; Yang, Li Lin

2012-12-14

We present a calculation of the perturbative quark-to-quark transverse parton distribution function at next-to-next-to-leading order based on a gauge invariant operator definition. We demonstrate for the first time that such a definition works beyond the first nontrivial order. We extract from our calculation the coefficient functions relevant for a next-to-next-to-next-to-leading logarithmic Q(T) resummation in a large class of processes at hadron colliders.

Statistical techniques for the characterization of partially observed epidemics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Safta, Cosmin; Ray, Jaideep; Crary, David

Techniques appear promising to construct and integrate automated detect-and-characterize technique for epidemics - Working off biosurveillance data, and provides information on the particular/ongoing outbreak. Potential use - in crisis management and planning, resource allocation - Parameter estimation capability ideal for providing the input parameters into an agent-based model, Index Cases, Time of Infection, infection rate. Non-communicable diseases are easier than communicable ones - Small anthrax can be characterized well with 7-10 days of data, post-detection; plague takes longer, Large attacks are very easy.

Validation of a New Method to Automatically Select Cases With Intraoperative Red Blood Cell Transfusion for Audit.

PubMed

Dexter, Franklin; Epstein, Richard H; Ledolter, Johannes; Dasovich, Susan M; Herman, Jay H; Maga, Joni M; Schwenk, Eric S

2018-05-01

Hospitals review allogeneic red blood cell (RBC) transfusions for appropriateness. Audit criteria have been published that apply to 5 common procedures. We expanded on this work to study the management decision of selecting which cases involving transfusion of at least 1 RBC unit to audit (review) among all surgical procedures, including those previously studied. This retrospective, observational study included 400,000 cases among 1891 different procedures over an 11-year period. There were 12,616 cases with RBC transfusion. We studied the proportions of cases that would be audited based on criteria of nadir hemoglobin (Hb) greater than the hospital's selected transfusion threshold, or absent Hb or missing estimated blood loss (EBL) among procedures with median EBL <500 mL. This threshold EBL was selected because it is approximately the volume removed during the donation of a single unit of whole blood at a blood bank. Missing EBL is important to the audit decision for cases in which the procedures' median EBL is <500 mL because, without an indication of the extent of bleeding, there are insufficient data to assume that there was sufficient blood loss to justify the transfusion. Most cases (>50%) that would be audited and most cases (>50%) with transfusion were among procedures with median EBL <500 mL (P < .0001). Among cases with transfusion and nadir Hb >9 g/dL, the procedure's median EBL was <500 mL for 3.0 times more cases than for procedures having a median EBL ≥500 mL. A greater percentage of cases would be recommended for audit based on missing values for Hb and/or EBL than based on exceeding the Hb threshold among cases of procedures with median EBL ≥500 mL (P < .0001). There were 3.7 times as many cases with transfusion that had missing values for Hb and/or EBL than had a nadir Hb >9 g/dL and median EBL for the procedure ≥500 mL. An automated process to select cases for audit of intraoperative transfusion of RBC needs to consider the median EBL of the procedure, whether the nadir Hb is below the hospital's Hb transfusion threshold for surgical cases, and the absence of either a Hb or entry of the EBL for the case. This conclusion applies to all surgical cases and procedures.

Identification of Shifts and Trends in Hydrometric Data in Canada Based on Several Detection Tests

NASA Astrophysics Data System (ADS)

Lauzon, N.; Lence, B. J.

2004-05-01

This work proposes new detection tests based on the Kohonen neural network and on fuzzy c-means for the identification of shifts and trends in data sequences. Annual mean and maximum flow sequences are considered as application case, for they have often been considered for the study of shifts and trends in hydrologic data. In recent years, several studies for the identification of trends have been accomplished with North American hydrometric data, often making use of only one detection test. The assumption here is that one cannot rely on only one test, and consequently several are employed in this work. A total of eight tests are considered, four for shifts and four for trends. Four of these tests, two for shifts and two for trends, are conventional statistical tests that are regularly employed, while the other four are developed based on the Kohonen neural network and on fuzzy c-means. Data from a group of 40 hydrometric stations across Canada are assessed for the detection of shifts and trends in time periods of 30, 40 and 50 years. While the results obtained confirm the conclusions of previous studies performed on similar groups of data, they also indicate that each test may behave differently from one another. For example, one test may detect a trend in a given sequence while the other tests do not, or vice-versa. Thus, the strategy of using several tests ensures not only that they may confirm each others diagnostics but also may complement each other in the case of divergent diagnostics, with the possibility of improving the final conclusion on the detection of shifts and trends. Using artificial intelligence techniques for the construction of detection tests constitutes also a departure from the use of statistics, and a discussion in this work on complementary studies (i.e. detection on multivariate cases) highlights the possibility of enhanced performance by the artificial intelligence-based tests compared with conventional detection tests.

Boundary work for implementing adaptive management: A water sector application.

PubMed

Adem Esmail, Blal; Geneletti, Davide; Albert, Christian

2017-09-01

Boundary work, defined as effort to mediate between knowledge and action, is a promising approach for facilitating knowledge co-production for sustainable development. Here, we investigate a case study of knowledge co-production, to assess the applicability of boundary work as a conceptual framework to support implementing adaptive management in the water sector. We refer to a boundary work classification recently proposed by Clark et al., (2016), based on three types of knowledge uses, i.e. enlightenment, decision-, and negotiation-support, and three types of sources, i.e. personal expertise, single, and multiple communities of expertise. Our empirical results confirm boundary work has been crucial for the three types of knowledge use. For enlightenment and decision-support, effective interaction among knowledge producers and users was achieved through diverse boundary work practices, including joint agenda setting, and sharing of data and expertise. This initial boundary work eased subsequent knowledge co-production for decision-support and negotiations, in combination with stepping up of cooperation between relevant actors, suitable legislation and pressure for problem solving. Our analysis highlighted the temporal dimension matters - building trust around enlightenment first, and then using this as a basis for managing knowledge co-production for decision-, and negotiation support. We reconfirmed that boundary work is not a single time achievement, rather is a dynamic process, and we emphasized the importance of key actors driving the process, such as water utilities. Our results provide a rich case study of how strategic boundary work can facilitate knowledge co-production for adaptive management in the water sector. The boundary work practices employed here could also be transferred to other cases. Water utilities, as intermediaries between providers and beneficiaries of the important water-related ecosystem service of clean water provision, can indeed serve as key actors for initiating such boundary work practices. Copyright © 2017 Elsevier B.V. All rights reserved.

Combating Learning

ERIC Educational Resources Information Center

Jarvensivu, Anu; Koski, Pasi

2012-01-01

Purpose: The purpose of this paper is to look at workplace learning through research into sociology of work. It explores the "learning discourse" at work place level looking for possibilities to oppose learning. Design/methodology/approach: This paper is based on case studies conducted at six workplaces. The data on the cases include…

Cancer and treatment effects on job task performance for gynecological cancer survivors.

PubMed

Nachreiner, Nancy M; Shanley, Ryan; Ghebre, Rahel G

2013-01-01

Over 91,000 new cases of gynecological cancers are expected to be diagnosed in 2013 in the US alone. As cancer detection technology and treatment options improve, the number of working-age cancer survivors continues to grow. To describe US gynecological cancer survivors' perceptions of the effects of cancer and treatment on their job tasks. 104 adult gynecological cancer survivors who were working at the time of their cancer diagnosis, treated at a University-based women's health clinic, diagnosed in the previous 24 months, and spoke English. Women completed written surveys to describe their work experiences following diagnosis. Clinical characteristics were obtained through medical record review. Descriptive statistics and cross tabulations were performed to describe characteristics and associations. Fifteen percent of women had chemotherapy and radiation treatment; 48% had only chemotherapy, 9% only radiation therapy, and 28% had neither. Survivors described the frequency of performing seven job tasks, such as 'intense concentration', 'analyzing data', and 'lifting heavy loads.' Women who had undergone radiation treatment were more likely to indicate limitations for physical tasks; women undergoing chemotherapy were more likely to report limitations in more analytic tasks. Only 29% of women noted an employer-based policy facilitated their return-to-work process. Cancer and treatment have important effects on job performance and may vary by type of treatment. Employer-based policies focusing on improved communication and work accommodations may improve the return to work process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deka, Deepjyoti; Backhaus, Scott N.; Chertkov, Michael

Limited placement of real-time monitoring devices in the distribution grid, recent trends notwithstanding, has prevented the easy implementation of demand-response and other smart grid applications. Part I of this paper discusses the problem of learning the operational structure of the grid from nodal voltage measurements. In this work (Part II), the learning of the operational radial structure is coupled with the problem of estimating nodal consumption statistics and inferring the line parameters in the grid. Based on a Linear-Coupled(LC) approximation of AC power flows equations, polynomial time algorithms are designed to identify the structure and estimate nodal load characteristics and/ormore » line parameters in the grid using the available nodal voltage measurements. Then the structure learning algorithm is extended to cases with missing data, where available observations are limited to a fraction of the grid nodes. The efficacy of the presented algorithms are demonstrated through simulations on several distribution test cases.« less

Tracking cohesive subgroups over time in inferred social networks

NASA Astrophysics Data System (ADS)

Chin, Alvin; Chignell, Mark; Wang, Hao

2010-04-01

As a first step in the development of community trackers for large-scale online interaction, this paper shows how cohesive subgroup analysis using the Social Cohesion Analysis of Networks (SCAN; Chin and Chignell 2008) and Data-Intensive Socially Similar Evolving Community Tracker (DISSECT; Chin and Chignell 2010) methods can be applied to the problem of identifying cohesive subgroups and tracking them over time. Three case studies are reported, and the findings are used to evaluate how well the SCAN and DISSECT methods work for different types of data. In the largest of the case studies, variations in temporal cohesiveness are identified across a set of subgroups extracted from the inferred social network. Further modifications to the DISSECT methodology are suggested based on the results obtained. The paper concludes with recommendations concerning further research that would be beneficial in addressing the community tracking problem for online data.

Value-Based Requirements Traceability: Lessons Learned

NASA Astrophysics Data System (ADS)

Egyed, Alexander; Grünbacher, Paul; Heindl, Matthias; Biffl, Stefan

Traceability from requirements to code is mandated by numerous software development standards. These standards, however, are not explicit about the appropriate level of quality of trace links. From a technical perspective, trace quality should meet the needs of the intended trace utilizations. Unfortunately, long-term trace utilizations are typically unknown at the time of trace acquisition which represents a dilemma for many companies. This chapter suggests ways to balance the cost and benefits of requirements traceability. We present data from three case studies demonstrating that trace acquisition requires broad coverage but can tolerate imprecision. With this trade-off our lessons learned suggest a traceability strategy that (1) provides trace links more quickly, (2) refines trace links according to user-defined value considerations, and (3) supports the later refinement of trace links in case the initial value consideration has changed over time. The scope of our work considers the entire life cycle of traceability instead of just the creation of trace links.

Older women public sector workers in Ireland: Decisions about retirement timing.

PubMed

Léime, Áine Ní

2017-01-01

Older women workers' decision making around retirement is increasingly important given the increasing involvement of older women in paid employment. This article explores influences on the retirement decision making of older women workers in Ireland. It is based on a case study of 57 interviews with women in the Irish civil service exploring work-life decision making. It finds that retirement choices vary according to initial socioeconomic resources and/or life-course trajectories and are particularly affected by gendered caring norms, employment policy, job tenure, and place in organizational hierarchies. Those women with interrupted careers and low pay have fewer choices around retirement timing.

Analysis of Scattering from Archival Pulsar Data using a CLEAN-based Method

NASA Astrophysics Data System (ADS)

Tsai, -Wei, Jr.; Simonetti, John H.; Kavic, Michael

2017-02-01

In this work, we adopted a CLEAN-based method to determine the scatter time, τ, from archived pulsar profiles under both the thin screen and uniform medium scattering models and to calculate the scatter time frequency scale index α, where τ \\propto {ν }α . The value of α is -4.4, if a Kolmogorov spectrum of the interstellar medium turbulence is assumed. We deconvolved 1342 profiles from 347 pulsars over a broad range of frequencies and dispersion measures. In our survey, in the majority of cases the scattering effect was not significant compared to pulse profile widths. For a subset of 21 pulsars scattering at the lowest frequencies was large enough to be measured. Because reliable scatter time measurements were determined only for the lowest frequency, we were limited to using upper limits on scatter times at higher frequencies for the purpose of our scatter time frequency slope estimation. We scaled the deconvolved scatter time to 1 GHz assuming α =-4.4 and considered our results in the context of other observations which yielded a broad relation between scatter time and dispersion measure.

Spectra and spacecraft

NASA Astrophysics Data System (ADS)

Moroz, V. I.

2001-02-01

In June 1999, Dr. Regis Courtin, Associate Editor of PSS, suggested that I write an article for the new section of this journal: "Planetary Pioneers". I hesitated , but decided to try. One of the reasons for my doubts was my primitive English, so I owe the reader an apology for this in advance. Writing took me much more time than I supposed initially, I have stopped and again returned to manuscript many times. My professional life may be divided into three main phases: pioneering work in ground-based IR astronomy with an emphasis on planetary spectroscopy (1955-1970), studies of the planets with spacecraft (1970-1989), and attempts to proceed with this work in difficult times. I moved ahead using the known method of trials and errors as most of us do. In fact, only a small percentage of efforts led to some important results, a sort of dry residue. I will try to describe below how has it been in my case: what may be estimated as the most important, how I came to this, what was around, etc.

[Risk factors for absenteeism due to sick leave in the petroleum industry].

PubMed

Oenning, Nágila Soares Xavier; Carvalho, Fernando Martins; Lima, Veronica Maria Cadena

2014-02-01

To identify risk factors for absenteeism among workers with sick leave in an oil company. A case-control study (120 cases and 656 controls) nested in a retrospective cohort study following up all employees of an oil company in the North-Northeast of Brazil from 2007 to 2009. The response variable used to represent absenteeism with sick leave was the average incidence of sick leave, defined as the ratio between total sick days and potential working days in the period. Logistic regression techniques were used to investigate the association between average incidence of sick leave > 5.0% over the period and the variables sex, position, age, time at work, shift work, smoking, arterial hypertension, body mass index, physical activity, coronary risk, sleep, glycemia, non-managed diabetes, cardiovascular, digestive, musculoskeletal, neurological and neoplastic diseases, straining body positioning during work, satisfaction at work, relationship with management, and concentrated attention at work. Average incidence of sick leave higher than 5.0% in the cohort period was 15.5%. The logistic model revealed that workers with average incidence of sick leave higher than 5.0% were 2.6 times more likely to be female; 2.0 time more likely to be smokers; 1.8 time more likely to be former smokers; 2.2 times more likely to report abnormal sleep and 10.5 times more likely to report dissatisfaction with their than workers with average incidence of sick leave ≤ 5.0% in the period. In this population, female gender, being a smoker or a former smoker, reporting dissatisfaction with the job and reporting abnormal sleep are good predictors of occupational absenteeism with sick leave. To identify risk factors for absenteeism among workers with sick leave in an oil company. A case-control study (120 cases and 656 controls) nested in a retrospective cohort study following up all employees of an oil company in the North-Northeast of Brazil from 2007 to 2009. The response variable used to represent absenteeism with sick leave was the average incidence of sick leave, defined as the ratio between total sick days and potential working days in the period. Logistic regression techniques were used to investigate the association between average incidence of sick leave > 5.0% over the period and the variables sex, position, age, time at work, shift work, smoking, arterial hypertension, body mass index, physical activity, coronary risk, sleep, glycemia, non-managed diabetes, cardiovascular, digestive, musculoskeletal, neurological and neoplastic diseases, straining body positioning during work, satisfaction at work, relationship with management, and concentrated attention at work. Average incidence of sick leave higher than 5.0% in the cohort period was 15.5%. The logistic model revealed that workers with average incidence of sick leave higher than 5.0% were 2.6 times more likely to be female; 2.0 time more likely to be smokers; 1.8 time more likely to be former smokers; 2.2 times more likely to report abnormal sleep and 10.5 times more likely to report dissatisfaction with their than workers with average incidence of sick leave ≤ 5.0% in the period. In this population, female gender, being a smoker or a former smoker, reporting dissatisfaction with the job and reporting abnormal sleep are good predictors of occupational absenteeism with sick leave.

Chronic fatigue syndrome‐like caseness as a predictor of work status in fatigued employees on sick leave: four year follow up study

PubMed Central

Huibers, M J H; Leone, S S; Kant, IJ; Knottnerus, J A

2006-01-01

Objective To assess whether CFS‐like caseness (meeting the criteria for chronic fatigue syndrome (CFS)) predicts work status in the long term. Methods Prospective study in a sample of fatigued employees absent from work. Data were collected at baseline and four years later, and included CFS‐like caseness and work status (inactive work status and full work incapacity). Results CFS‐like cases at baseline were three times more likely to be unable to work at follow up than fatigued employees who did not meet CFS criteria at baseline (ORs 3–3.3). These associations grew even stronger when demographic and clinical confounders were controlled for (ORs 3.4–4.4). Conclusion A CFS‐like status (compared to non‐CFS fatigue) proved to be a strong predictor of an inactive work status and full work incapacity in the long term. Since little is known about effective interventions that prevent absenteeism and work incapacity or facilitate return to work in subjects with chronic fatigue, there is a great need for powerful early interventions that restore or preserve the ability to work, especially for workers who meet criteria for CFS. PMID:16698810

A simplified method for assessing cytotechnologist workload.

PubMed

Vaickus, Louis J; Tambouret, Rosemary

2014-01-01

Examining cytotechnologist workflow and how it relates to job performance and patient safety is important in determining guidelines governing allowable workloads. This report discusses the development of a software tool that significantly simplifies the process of analyzing cytotechnologist workload while simultaneously increasing the quantity and resolution of the data collected. The program runs in Microsoft Excel and minimizes manual data entry and data transcription by automating as many tasks as is feasible. Data show the cytotechnologists tested were remarkably consistent in the amount of time it took them to screen a cervical cytology (Gyn) or a nongynecologic cytology (Non-Gyn) case and that this amount of time was directly proportional to the number of slides per case. Namely, the time spent per slide did not differ significantly in Gyn versus Non-Gyn cases (216 ± 3.4 seconds and 235 ± 24.6 seconds, respectively; P=.16). There was no significant difference in the amount of time needed to complete a Gyn case between the morning and the evening (314 ± 4.7 seconds and 312 ± 7.1 seconds; P=.39), but a significantly increased time spent screening Non-Gyn cases (slide-adjusted) in the afternoon hours (323 ± 20.1 seconds and 454 ± 67.6 seconds; P=.027), which was largely the result of significantly increased time spent on prescreening activities such as checking the electronic medical record (62 ± 6.9 seconds and 145 ± 36 seconds; P=.006). This Excel-based data collection tool generates highly detailed data in an unobtrusive manner and is highly customizable to the individual working environment and clinical climate. © 2013 American Cancer Society.

Exploring the Work/Life/Study Balance: The Experience of Higher Education Students in a Scottish Further Education College

ERIC Educational Resources Information Center

Lowe, Janet; Gayle, Vernon

2007-01-01

This study explores the dimensions of the work/life/study balance and its influence on student participation in higher education, through a case study of the experience of higher education students, studying both full time and part time, in a Scottish further education college. The experience of the students and the work/life/study challenges that…

Moderating Role of Acculturation in a Mediation Model of Work-Family Conflict among Chinese Immigrants in New Zealand.

PubMed

Shang, Sudong; O'Driscoll, Michael P; Roche, Maree

2017-02-01

This study examined the antecedents of work-family conflict (WFC) and the mediation effects of WFC on well-being consequences among Chinese immigrants to New Zealand, along with the moderating role of acculturation. Four types of WFC were explored: time-based and strain-based work interference with family, and time-based and strain-based family interference with work. Data were collected from 577 Chinese immigrants in New Zealand, who had full-time or part-time work and lived with family members in New Zealand. The four types of WFC were differentially related to the antecedents and well-being consequences, providing some evidence that both Chinese and New Zealand cultures may exert influences on Chinese immigrants' experiences of WFC. Both directions of WFC (work interference with family, and family interference with work) were related to job satisfaction and family satisfaction, and strain-based WFC influenced their well-being more than time-based WFC. Most importantly, we found immigrants who were proficient in English perceived greater WFC and psychological strain. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Determination of work function of graphene under a metal electrode and its role in contact resistance.

PubMed

Song, Seung Min; Park, Jong Kyung; Sul, One Jae; Cho, Byung Jin

2012-08-08

Although the work function of graphene under a given metal electrode is critical information for the realization of high-performance graphene-based electronic devices, relatively little relevant research has been carried out to date. In this work, the work function values of graphene under various metals are accurately measured for the first time through a detailed analysis of the capacitance-voltage (C-V) characteristics of a metal-graphene-oxide-semiconductor (MGOS) capacitor structure. In contrast to the high work function of exposed graphene of 4.89-5.16 eV, the work function of graphene under a metal electrode varies depending on the metal species. With a Cr/Au or Ni contact, the work function of graphene is pinned to that of the contacted metal, whereas with a Pd or Au contact the work function assumes a value of ∼4.62 eV regardless of the work function of the contact metal. A study of the gate voltage dependence on the contact resistance shows that the latter case provides lower contact resistance.

Application of Time-Delay Absorber to Suppress Vibration of a Dynamical System to Tuned Excitation.

PubMed

El-Ganaini, W A A; El-Gohary, H A

2014-08-01

In this work, we present a comprehensive investigation of the time delay absorber effects on the control of a dynamical system represented by a cantilever beam subjected to tuned excitation forces. Cantilever beam is one of the most widely used system in too many engineering applications, such as mechanical and civil engineering. The main aim of this work is to control the vibration of the beam at simultaneous internal and combined resonance condition, as it is the worst resonance case. Control is conducted via time delay absorber to suppress chaotic vibrations. Time delays often appear in many control systems in the state, in the control input, or in the measurements. Time delay commonly exists in various engineering, biological, and economical systems because of the finite speed of the information processing. It is a source of performance degradation and instability. Multiple time scale perturbation method is applied to obtain a first order approximation for the nonlinear differential equations describing the system behavior. The different resonance cases are reported and studied numerically. The stability of the steady-state solution at the selected worst resonance case is investigated applying Runge-Kutta fourth order method and frequency response equations via Matlab 7.0 and Maple11. Time delay absorber is effective, but within a specified range of time delay. It is the critical factor in selecting such absorber. Time delay absorber is better than the ordinary one as from the effectiveness point of view. The effects of the different absorber parameters on the system behavior and stability are studied numerically. A comparison with the available published work showed a close agreement with some previously published work.

Noncanonical spike-related BOLD responses in focal epilepsy

PubMed Central

Lemieux, Louis; Laufs, Helmut; Carmichael, David; Paul, Joseph Suresh; Walker, Matthew C; Duncan, John S

2008-01-01

Till now, most studies of the Blood Oxygen Level-Dependent (BOLD) response to interictal epileptic discharges (IED) have assumed that its time course matches closely to that of brief physiological stimuli, commonly called the canonical event-related haemodynamic response function (canonical HRF). Analyses based on that assumption have produced significant response patterns that are generally concordant with prior electroclinical data. In this work, we used a more flexible model of the event-related response, a Fourier basis set, to investigate the presence of other responses in relation to individual IED in 30 experiments in patients with focal epilepsy. We found significant responses that had a noncanonical time course in 37% of cases, compared with 40% for the conventional, canonical HRF-based approach. In two cases, the Fourier analysis suggested activations where the conventional model did not. The noncanonical activations were almost always remote from the presumed generator of epileptiform activity. In the majority of cases with noncanonical responses, the noncanonical responses in single-voxel clusters were suggestive of artifacts. We did not find evidence for IED-related noncanonical HRFs arising from areas of pathology, suggesting that the BOLD response to IED is primarily canonical. Noncanonical responses may represent a number of phenomena, including artefacts and propagated epileptiform activity. Hum Brain Mapp 2008. © 2007 Wiley-Liss, Inc. PMID:17510926

Visual and Spatial Working Memory Are Not that Dissociated after All: A Time-Based Resource-Sharing Account

ERIC Educational Resources Information Center

Vergauwe, Evie; Barrouillet, Pierre; Camos, Valerie

2009-01-01

Examinations of interference between visual and spatial materials in working memory have suggested domain- and process-based fractionations of visuo-spatial working memory. The present study examined the role of central time-based resource sharing in visuo-spatial working memory and assessed its role in obtained interference patterns. Visual and…

Partial differential equation-based approach for empirical mode decomposition: application on image analysis.

PubMed

Niang, Oumar; Thioune, Abdoulaye; El Gueirea, Mouhamed Cheikh; Deléchelle, Eric; Lemoine, Jacques

2012-09-01

The major problem with the empirical mode decomposition (EMD) algorithm is its lack of a theoretical framework. So, it is difficult to characterize and evaluate this approach. In this paper, we propose, in the 2-D case, the use of an alternative implementation to the algorithmic definition of the so-called "sifting process" used in the original Huang's EMD method. This approach, especially based on partial differential equations (PDEs), was presented by Niang in previous works, in 2005 and 2007, and relies on a nonlinear diffusion-based filtering process to solve the mean envelope estimation problem. In the 1-D case, the efficiency of the PDE-based method, compared to the original EMD algorithmic version, was also illustrated in a recent paper. Recently, several 2-D extensions of the EMD method have been proposed. Despite some effort, 2-D versions for EMD appear poorly performing and are very time consuming. So in this paper, an extension to the 2-D space of the PDE-based approach is extensively described. This approach has been applied in cases of both signal and image decomposition. The obtained results confirm the usefulness of the new PDE-based sifting process for the decomposition of various kinds of data. Some results have been provided in the case of image decomposition. The effectiveness of the approach encourages its use in a number of signal and image applications such as denoising, detrending, or texture analysis.

Dynamic vehicle routing with time windows in theory and practice.

PubMed

Yang, Zhiwei; van Osta, Jan-Paul; van Veen, Barry; van Krevelen, Rick; van Klaveren, Richard; Stam, Andries; Kok, Joost; Bäck, Thomas; Emmerich, Michael

2017-01-01

The vehicle routing problem is a classical combinatorial optimization problem. This work is about a variant of the vehicle routing problem with dynamically changing orders and time windows. In real-world applications often the demands change during operation time. New orders occur and others are canceled. In this case new schedules need to be generated on-the-fly. Online optimization algorithms for dynamical vehicle routing address this problem but so far they do not consider time windows. Moreover, to match the scenarios found in real-world problems adaptations of benchmarks are required. In this paper, a practical problem is modeled based on the procedure of daily routing of a delivery company. New orders by customers are introduced dynamically during the working day and need to be integrated into the schedule. A multiple ant colony algorithm combined with powerful local search procedures is proposed to solve the dynamic vehicle routing problem with time windows. The performance is tested on a new benchmark based on simulations of a working day. The problems are taken from Solomon's benchmarks but a certain percentage of the orders are only revealed to the algorithm during operation time. Different versions of the MACS algorithm are tested and a high performing variant is identified. Finally, the algorithm is tested in situ: In a field study, the algorithm schedules a fleet of cars for a surveillance company. We compare the performance of the algorithm to that of the procedure used by the company and we summarize insights gained from the implementation of the real-world study. The results show that the multiple ant colony algorithm can get a much better solution on the academic benchmark problem and also can be integrated in a real-world environment.

An information-theoretic approach to surrogate-marker evaluation with failure time endpoints.

PubMed

Pryseley, Assam; Tilahun, Abel; Alonso, Ariel; Molenberghs, Geert

2011-04-01

Over the last decades, the evaluation of potential surrogate endpoints in clinical trials has steadily been growing in importance, not only thanks to the availability of ever more potential markers and surrogate endpoints, also because more methodological development has become available. While early work has been devoted, to a large extent, to Gaussian, binary, and longitudinal endpoints, the case of time-to-event endpoints is in need of careful scrutiny as well, owing to the strong presence of such endpoints in oncology and beyond. While work had been done in the past, it was often cumbersome to use such tools in practice, because of the need for fitting copula or frailty models that were further embedded in a hierarchical or two-stage modeling approach. In this paper, we present a methodologically elegant and easy-to-use approach based on information theory. We resolve essential issues, including the quantification of "surrogacy" based on such an approach. Our results are put to the test in a simulation study and are applied to data from clinical trials in oncology. The methodology has been implemented in R.

From Opinion-Based to Evidence-Based Social Work: The Swedish Case

ERIC Educational Resources Information Center

Sundell, Knut; Soydan, Haluk; Tengvald, Karin; Anttila, Sten

2010-01-01

This article presents an account of Sweden's Institute for Evidence-Based Social Work Practice (IMS), located in Stockholm, Sweden. The article places IMS in the context of making Swedish social care services less opinion-based and more evidence-based. The institute is an example of how policy-driven processes promote the use of evidence-based…

Exact analytic solutions for a global equation of plant cell growth.

PubMed

Pietruszka, Mariusz

2010-05-21

A generalization of the Lockhart equation for plant cell expansion in isotropic case is presented. The goal is to account for the temporal variation in the wall mechanical properties--in this case by making the wall extensibility a time dependent parameter. We introduce a time-differential equation describing the plant growth process with some key biophysical aspects considered. The aim of this work was to improve prior modeling efforts by taking into account the dynamic character of the plant cell wall with characteristics reminiscent of damped (aperiodic) motion. The equations selected to encapsulate the time evolution of the wall extensibility offer a new insight into the control of cell wall expansion. We find that the solutions to the time dependent second order differential equation reproduce much of the known experimental data for long- and short-time scales. Additionally, in order to support the biomechanical approach, a new growth equation based on the action of expansin proteins is proposed. Remarkably, both methods independently converge to the same kind, sigmoid-shaped, growth description functional V(t) proportional, exp(-exp(-t)), properly describing the volumetric growth and, consequently, growth rate as its time derivative. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Comparison of Canadian and Swiss Surgical Training Curricula: Moving on Toward Competency-Based Surgical Education.

PubMed

Hoffmann, Henry; Oertli, Daniel; Mechera, Robert; Dell-Kuster, Salome; Rosenthal, Rachel; Reznick, Richard; MacDonald, Hugh

Quality of surgical training in the era of resident duty-hour restrictions (RDHR) is part of an ongoing debate. Most training elements are provided during surgical service. As exposure to surgical procedures is important but time-consuming, RDHR may affect quality of surgical training. Providing structured training elements may help to compensate for this shortcoming. This binational anonymous questionnaire-based study evaluates frequency, time, and structure of surgical training programs at 2 typical academic teaching hospitals with different RDHR. Departments of Surgery of University of Basel (Basel, Switzerland) and the Queen's University (Kingston, Ontario, Canada). Surgical consultants and residents of the Queen's University Hospital (Kingston, Ontario, Canada) and the University Hospital Basel (Basel, Switzerland) were eligible for this study. Questionnaire response rate was 37% (105/284). Queen's residents work 80 hours per week, receiving 7 hours of formal training (8.8% of workweek). Basel residents work 60 hours per week, including 1 hour of formal training (1.7% of working time). Queen's faculty and residents rated their program as "structured" or "rather structured" in contrast to Basel faculty and residents who rated their programs as "neutral" in structure or "unstructured." Respondents identified specific structured training elements more frequently at Queen's than in Basel. Two-thirds of residents responded that they seek out additional surgical experiences through voluntary extra work. Basel participants articulated a stronger need for improvement of current surgical training. Although Basel residents and consultants in both institutions fear negative influence of RDHR on the training program, this was not the case in Queen's residents. Providing more structured surgical training elements may be advantageous in providing optimal-quality surgical education in an era of work-hour restrictions. Copyright © 2016 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Universal Verification Methodology Based Register Test Automation Flow.

PubMed

Woo, Jae Hun; Cho, Yong Kwan; Park, Sun Kyu

2016-05-01

In today's SoC design, the number of registers has been increased along with complexity of hardware blocks. Register validation is a time-consuming and error-pron task. Therefore, we need an efficient way to perform verification with less effort in shorter time. In this work, we suggest register test automation flow based UVM (Universal Verification Methodology). UVM provides a standard methodology, called a register model, to facilitate stimulus generation and functional checking of registers. However, it is not easy for designers to create register models for their functional blocks or integrate models in test-bench environment because it requires knowledge of SystemVerilog and UVM libraries. For the creation of register models, many commercial tools support a register model generation from register specification described in IP-XACT, but it is time-consuming to describe register specification in IP-XACT format. For easy creation of register model, we propose spreadsheet-based register template which is translated to IP-XACT description, from which register models can be easily generated using commercial tools. On the other hand, we also automate all the steps involved integrating test-bench and generating test-cases, so that designers may use register model without detailed knowledge of UVM or SystemVerilog. This automation flow involves generating and connecting test-bench components (e.g., driver, checker, bus adaptor, etc.) and writing test sequence for each type of register test-case. With the proposed flow, designers can save considerable amount of time to verify functionality of registers.

The prevalence and incidence of work absenteeism involving neck pain: a cohort of Ontario lost-time claimants.

PubMed

Côté, Pierre; Kristman, Vicki; Vidmar, Marjan; Van Eerd, Dwayne; Hogg-Johnson, Sheilah; Beaton, Dorcas; Smith, Peter M

2008-02-15

Cohort study. To measure the prevalence and incidence of work absenteeism involving neck pain in a cohort of claimants to the Ontario Workplace Safety & Insurance Board (WSIB). According to workers' compensation statistics, neck pain accounts for a small proportion of lost-time claims. However, these statistics may be biased by an underenumeration of claimants with neck disorders. We studied all lost-time claimants to the Ontario WSIB in 1998 and used 2 methods to enumerate neck pain cases. We report the prevalence and incidence of neck pain using 2 denominators: (1) annual number of lost-time claimants and (2) an estimate of the Ontario working population covered by the WSIB. The estimated percentage of lost-time claimants with neck pain ranged from 2.8% (95% CI 2.5-3.3) using only codes specific for neck pain to 11.3% (95% CI 9.5-13.1) using a weighted estimate of codes capturing neck pain cases. The health care sector had the highest percentage of claims with neck pain. The annual incidence of neck pain among the Ontario working population ranged from 6 per 10,000 full-time equivalents (FTE) (95% CI 5-6) to 23 per 10,000 FTE (95% CI 20-27) depending on the codes used to capture neck pain. Male workers between the ages of 20 and 39 years were the most likely to experience an episode of work absenteeism involving neck pain. Neck pain is a common and burdensome problem for Ontario workers. Our study highlights the importance of properly capturing all neck pain cases when describing its prevalence and incidence.

Earthworks logistics in the high density urban development conditions - case study

NASA Astrophysics Data System (ADS)

Sobotka, A.; Blajer, M.

2017-10-01

Realisation of the construction projects on highly urbanised areas carries many difficulties and logistic problems. Earthworks conducted in such conditions constitute a good example of how important it is to properly plan the works and use the technical means of the logistics infrastructure. The construction processes on the observed construction site, in combination with their external logistics service are a complex system, difficult for mathematical modelling and achievement of appropriate data for planning the works. The paper shows describe and analysis of earthworks during construction of the Centre of Power Engineering of AGH in Krakow for two stages of a construction project. At the planning stage in the preparatory phase (before realization) and in the implementation phase of construction works (foundation). In the first case, an example of the use of queuing theory for prediction of excavation time under random work conditions of the excavator and the associated trucks is provided. In the second case there is a change of foundation works technology resulting as a consequence of changes in logistics earthworks. Observation of the construction has confirmed that the use of appropriate methods of construction works management, and in this case agile management, the time and cost of the project have not been exceeded. The success of a project depends on the ability of the contractor to react quickly when changes occur in the design, technology, environment, etc.

Agreement between Myocardial Infarction Patients and Their Spouses on Reporting of Data on 82 Cardiovascular Risk Exposures.

PubMed

Quintana, Hedley Knewjen; Vikström, Max; Andersson, Tomas; Hallqvist, Johan; Leander, Karin

2015-01-01

The validity of exposure data collected from proxy respondents of myocardial infarction patients has scarcely been studied. We assessed the level of disagreement between myocardial infarction patients and their spouses with respect to the reporting of the patient´s cardiovascular risk exposures. Within the frame of the Stockholm Heart Epidemiology Program (SHEEP), a case-control study of risk factors of myocardial infarction performed in Stockholm county 1992-1994, a subset of 327 first time myocardial infarction cases aged 45-70 who survived >28 days after the event and who co-habited with a spouse or common-law spouse (proxy) were identified between 1993-04-05 and 1993-12-31. Among these, 243 cases participated along with their respective proxy in the present study. Control individuals, matched to cases by age, sex and residential area were also included (n = 243). Data were collected using questionnaires. Using conditional logistic regression we calculated for each of 82 exposures the odds ratio based on information collected from 1) myocardial infarction cases and controls [odds ratio A] and 2) proxies and the same set of controls [odds ratio B]. Disagreement was measured by calculating the ratio between odds ratio B and odds ratio A with 95% confidence intervals (CI) calculated using resampling bootstrap. For the vast majority of the exposures considered including diet, smoking, education, work-related stress, and family history of CVD, there was no statistically significant disagreement between myocardial infarction patients and proxies (n = 243 pairs). However, leisure time physical inactivity (proxy bias = 1.59, 95% CI 1.05-3.57) was overestimated by spouses compared to myocardial infarction patients. A few other exposures including some sleep-related problems and work-related issues also showed disagreement. Myocardial infarction patients and their spouses similarly reported data on a wide range of exposures including the majority of the traditional cardiovascular risk factors, leisure time physical inactivity being an exception.

[Application of general retention time formula for gradient liquid chromatography in the studies of ladder-like gradient elution].

PubMed

Sun, Xiaoli; Hao, Weiqiang; Wang, Junde; Di, Bin; Chen, Qiang; Zhuang, Wei; Yu, Qiang; Zhang, Peipei

2013-08-01

By not explicitly specifying the type of solvent strength model, the features of ladder-like gradient elution were studied based on the general retention time formula that was derived in our previous work. For the case where the solute is eluted at like gradient, we derived the expression that connects the mobile phase composition (phiR), at which the solute is eluted from the column, with the gradient slope (B). It was shown that phiR will increase with the increase of B in this case. For the case where the solute is eluted at the last isocratic segment of the ladder-like gradient, it was proven that the retention time (tR) will correlate linearly with the reciprocal of the gradient slope (1/B) when the initial and final mobile phase compositions are set to be constant. In experiments, by taking biphenyl as the sample, the values of retention time in isocratic and gradient elution were measured on a C18 column by using a mixture of methanol and water as the mobile phase. The experimental values were found to be well consistent with the theoretical values that were calculated from the expressions. These expressions will be helpful to understand the features of the ladder-like gradient in practice.

Critical Pedagogy and APA: A Resonant (and Timely) Interdisciplinary Blend.

PubMed

Connolly, Maureen; Harvey, William J

2018-04-12

Critical pedagogy owes much of its emergence, development, and ongoing relevance to the work of Paulo Freire whose legacy remains relevant for a next generation of scholars who seek to explore issues of inclusion, oppression, social justice, and authentic expression. An interdisciplinary dialogue between critical pedagogy and adapted physical activity is timely, appropriate, and should focus on complex profiles of neurodiversity, mental illness, and mental health, with emphasis on pedagogic practices of practitioners in service delivery and teacher educators who prepare them for professional practice. A case-based scenario approach is used to present practitioner and teacher educator practices. Concrete examples are provided for analyzing and understanding deeper issues and challenges related to neurodiversity in a variety of embodied dimensions in educational and activity contexts. We work with Szostak's approach to interdisciplinary research and model an analysis strategy that integrates and applies the methodological features of interdisciplinarity, adapted physical activity, and critical pedagogy.

MS-Electronic Nose Performance Improvement Using GC Retention Times And 2-Way And 3-Way Data Processing Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burian, Cosmin; Llobet, Eduard; Vilanova, Xavier

We have designed a challenging experimental sample set in the form of 20 solutions with a high degree of similarity in order to study whether the addition of chromatographic separation information improves the performance of regular MS based electronic noses. In order to make an initial study of the approach, two different chromatographic methods were used. By processing the data of these experiments with 2 and 3-way algorithms, we have shown that the addition of chromatographic separation information improves the results compared to the 2-way analysis of mass spectra or total ion chromatogram treated separately. Our findings show that whenmore » the chromatographic peaks are resolved (longer measurement times), 2-way methods work better than 3-way methods, whereas in the case of a more challenging measurement (more coeluted chromatograms, much faster GC-MS measurements) 3-way methods work better.« less

A new type industrial total station based on target automatic collimation

NASA Astrophysics Data System (ADS)

Lao, Dabao; Zhou, Weihu; Ji, Rongyi; Dong, Dengfeng; Xiong, Zhi; Wei, Jiang

2018-01-01

In the case of industrial field measurement, the present measuring instruments work with manual operation and collimation, which give rise to low efficiency for field measurement. In order to solve the problem, a new type industrial total station is presented in this paper. The new instrument can identify and trace cooperative target automatically, in the mean time, coordinate of the target is measured in real time. For realizing the system, key technology including high precision absolutely distance measurement, small high accuracy angle measurement, target automatic collimation with vision, and quick precise controlling should be worked out. After customized system assemblage and adjustment, the new type industrial total station will be established. As the experiments demonstrated, the coordinate accuracy of the instrument is under 15ppm in the distance of 60m, which proved that the measuring system is feasible. The result showed that the total station can satisfy most industrial field measurement requirements.

Numerical comparison of grid pattern diffraction effects through measurement and modeling with OptiScan software

NASA Astrophysics Data System (ADS)

Murray, Ian B.; Densmore, Victor; Bora, Vaibhav; Pieratt, Matthew W.; Hibbard, Douglas L.; Milster, Tom D.

2011-06-01

Coatings of various metalized patterns are used for heating and electromagnetic interference (EMI) shielding applications. Previous work has focused on macro differences between different types of grids, and has shown good correlation between measurements and analyses of grid diffraction. To advance this work, we have utilized the University of Arizona's OptiScan software, which has been optimized for this application by using the Babinet Principle. When operating on an appropriate computer system, this algorithm produces results hundreds of times faster than standard Fourier-based methods, and allows realistic cases to be modeled for the first time. By using previously published derivations by Exotic Electro-Optics, we compare diffraction performance of repeating and randomized grid patterns with equivalent sheet resistance using numerical performance metrics. Grid patterns of each type are printed on optical substrates and measured energy is compared against modeled energy.

Teamwork and team decision-making at multidisciplinary cancer conferences: barriers, facilitators, and opportunities for improvement.

PubMed

Lamb, Benjamin W; Sevdalis, Nick; Arora, Sonal; Pinto, Anna; Vincent, Charles; Green, James S A

2011-09-01

Anecdotally, multidisciplinary cancer conferences (MCCs) do not always function optimally. MCC members' experiences with and attitudes toward MCCs are explored, and barriers to and facilitators of effective team-working are identified. A total of 19 semistructured interviews were conducted with surgeons, oncologists, nurses, and administrators. Interviews explored participants' opinions on MCC attendance, information presentation, case discussion, leadership, team decision-making, and possible improvements to MCC meetings. Nonattendance was associated with not having protected time to attend the MCC. Contributions to MCC discussions were unequal among the participants, and patient-centered information was ignored. Good leadership was necessary to foster inclusive case discussion. Members were positive about MCCs, but protected time, improved case selection, and working in a more structured way were possible improvements. Results are consistent with previous research: Members of the MCC are positive about the benefits of MCCs, although improving the way MCCs work is a goal.

Management of a growing Skeletal Class II Patient: A Case Report.

PubMed

Sharma, Narendra Shriram

2013-01-01

Sagittal and transverse discrepancies often coexist in skeletal class II malocclusions. Orthopedic growth modification can work well in such cases, provided that the remaining pubertal growth is adequate and that the clinician can provide timely treatment to coincide with the peak growth period. The transverse discrepancy is generally corrected first, establishing a proper base for the sagittal correction to follow. For example, in a skeletal class II case with a narrow maxillary arch and retrusive mandible, maxillary expansion is performed initially to facilitate functional mandibular advancement. The present article illustrates an exception to this rule, in a case where sagittal correction was undertaken before transverse correction to make optimal use of the patient's pubertal growth spurt in first phase followed by a second phase of fixed appliance therapy during adolescence to achieve optimal results. How to cite this article: Sharma NS. Management of a growing Skeletal Class II Patient: A Case Report. Int J Clin Pediatr Dent 2013;6(1):48-54.

Forecasting malaria incidence based on monthly case reports and environmental factors in Karuzi, Burundi, 1997–2003

PubMed Central

Gomez-Elipe, Alberto; Otero, Angel; van Herp, Michel; Aguirre-Jaime, Armando

2007-01-01

Background The objective of this work was to develop a model to predict malaria incidence in an area of unstable transmission by studying the association between environmental variables and disease dynamics. Methods The study was carried out in Karuzi, a province in the Burundi highlands, using time series of monthly notifications of malaria cases from local health facilities, data from rain and temperature records, and the normalized difference vegetation index (NDVI). Using autoregressive integrated moving average (ARIMA) methodology, a model showing the relation between monthly notifications of malaria cases and the environmental variables was developed. Results The best forecasting model (R2adj = 82%, p < 0.0001 and 93% forecasting accuracy in the range ± 4 cases per 100 inhabitants) included the NDVI, mean maximum temperature, rainfall and number of malaria cases in the preceding month. Conclusion This model is a simple and useful tool for producing reasonably reliable forecasts of the malaria incidence rate in the study area. PMID:17892540

Microfluidic droplet-based liquid-liquid extraction.

PubMed

Mary, Pascaline; Studer, Vincent; Tabeling, Patrick

2008-04-15

We study microfluidic systems in which mass exchanges take place between moving water droplets, formed on-chip, and an external phase (octanol). Here, no chemical reaction takes place, and the mass exchanges are driven by a contrast in chemical potential between the dispersed and continuous phases. We analyze the case where the microfluidic droplets, occupying the entire width of the channel, extract a solute-fluorescein-from the external phase (extraction) and the opposite case, where droplets reject a solute-rhodamine-into the external phase (purification). Four flow configurations are investigated, based on straight or zigzag microchannels. Additionally to the experimental work, we performed two-dimensional numerical simulations. In the experiments, we analyze the influence of different parameters on the process (channel dimensions, fluid viscosities, flow rates, drop size, droplet spacing, ...). Several regimes are singled out. In agreement with the mass transfer theory of Young et al. (Young, W.; Pumir, A.; Pomeau, Y. Phys. Fluids A 1989, 1, 462), we find that, after a short transient, the amount of matter transferred across the droplet interface grows as the square root of time and the time it takes for the transfer process to be completed decreases as Pe-2/3, where Pe is the Peclet number based on droplet velocity and radius. The numerical simulation is found in excellent consistency with the experiment. In practice, the transfer time ranges between a fraction and a few seconds, which is much faster than conventional systems.

Fighting poverty: the economic adjustment of female migrants in Dhaka.

PubMed

Huq-hussain, S

1995-10-01

Data from a field survey of slum and squatter settlements in Dhaka, Bangladesh, are used to examine the social adjustment of poor, female migrants to work, occupational choice, work satisfaction, income, control over income, and women's role in the family economy. A "poor household," defined in terms of nutritional intake, included those families receiving under 2122 cal/person/day. 44% of the urban population in Bangladesh do not obtain the daily nutritional requirement. Findings indicate that 61% of all female migrants expected to find work on arrival in the city. 44% of female migrants were willing to take any kind of work available at the time of arrival. Over 66% of all females found work in less than 6 months. Almost 25% took 6 months to a year to find a job, and 15% found work after a year's time. Recent migrants, who were older, found work quicker. 16% of female migrants found their job with help from relatives and friends (23% of recent migrants and 14% of long-term migrants). Among female migrants who sought a job on their own, 14% found work within 6 months. 3% found work between 6 months and a year. The rest were engaged in family and home-based work or found a job much later. In Dhaka, most women migrants worked in the service or informal sector. 40% of the sample worked as domestics, 38% worked in the informal sector, 16% worked in other informal work, and 5% worked in export-based garment industries. Most female migrants lived in the British Dhaka zone and the post-British Dhaka zone. Those living in the Mughal Dhaka zone tended to work in home-based informal activities. Garment industry workers tended to have more education. Women in the informal sector did not receive cash income. Just over 33% received income in kind, about 25% received a low income, and another 25% received a moderate income. In 71% of cases, husbands or fathers handled the money. 29% handled income on their own. Their own earnings went mostly for survival needs. Over 70% changed jobs more than once. 44% were satisfied with their work. Women were unhappy with low wages, tiring and hard work, and long working hours.

Making Total Quality Management + Just-in-Time Manufacturing Work.

ERIC Educational Resources Information Center

Waldrop, Phillip S.; Scott, Thomas E.

2000-01-01

In one case study, teamwork was implemented in mainstream production; in a second, teamwork was applied to an ad hoc project. The cases show that process technologies and management strategies such as just-in-time are not enough; selection of the appropriate mix of individuals with complementary traits is crucial. (SK)

Time and learning efficiency in Internet-based learning: a systematic review and meta-analysis.

PubMed

Cook, David A; Levinson, Anthony J; Garside, Sarah

2010-12-01

Authors have claimed that Internet-based instruction promotes greater learning efficiency than non-computer methods. determine, through a systematic synthesis of evidence in health professions education, how Internet-based instruction compares with non-computer instruction in time spent learning, and what features of Internet-based instruction are associated with improved learning efficiency. we searched databases including MEDLINE, CINAHL, EMBASE, and ERIC from 1990 through November 2008. STUDY SELECTION AND DATA ABSTRACTION we included all studies quantifying learning time for Internet-based instruction for health professionals, compared with other instruction. Reviewers worked independently, in duplicate, to abstract information on interventions, outcomes, and study design. we identified 20 eligible studies. Random effects meta-analysis of 8 studies comparing Internet-based with non-Internet instruction (positive numbers indicating Internet longer) revealed pooled effect size (ES) for time -0.10 (p = 0.63). Among comparisons of two Internet-based interventions, providing feedback adds time (ES 0.67, p =0.003, two studies), and greater interactivity generally takes longer (ES 0.25, p = 0.089, five studies). One study demonstrated that adapting to learner prior knowledge saves time without significantly affecting knowledge scores. Other studies revealed that audio narration, video clips, interactive models, and animations increase learning time but also facilitate higher knowledge and/or satisfaction. Across all studies, time correlated positively with knowledge outcomes (r = 0.53, p = 0.021). on average, Internet-based instruction and non-computer instruction require similar time. Instructional strategies to enhance feedback and interactivity typically prolong learning time, but in many cases also enhance learning outcomes. Isolated examples suggest potential for improving efficiency in Internet-based instruction.

Prediction model for the return to work of workers with injuries in Hong Kong.

PubMed

Xu, Yanwen; Chan, Chetwyn C H; Lo, Karen Hui Yu-Ling; Tang, Dan

2008-01-01

This study attempts to formulate a prediction model of return to work for a group of workers who have been suffering from chronic pain and physical injury while also being out of work in Hong Kong. The study used Case-based Reasoning (CBR) method, and compared the result with the statistical method of logistic regression model. The database of the algorithm of CBR was composed of 67 cases who were also used in the logistic regression model. The testing cases were 32 participants who had a similar background and characteristics to those in the database. The methods of setting constraints and Euclidean distance metric were used in CBR to search the closest cases to the trial case based on the matrix. The usefulness of the algorithm was tested on 32 new participants, and the accuracy of predicting return to work outcomes was 62.5%, which was no better than the 71.2% accuracy derived from the logistic regression model. The results of the study would enable us to have a better understanding of the CBR applied in the field of occupational rehabilitation by comparing with the conventional regression analysis. The findings would also shed light on the development of relevant interventions for the return-to-work process of these workers.

puma: a Bioconductor package for propagating uncertainty in microarray analysis.

PubMed

Pearson, Richard D; Liu, Xuejun; Sanguinetti, Guido; Milo, Marta; Lawrence, Neil D; Rattray, Magnus

2009-07-09

Most analyses of microarray data are based on point estimates of expression levels and ignore the uncertainty of such estimates. By determining uncertainties from Affymetrix GeneChip data and propagating these uncertainties to downstream analyses it has been shown that we can improve results of differential expression detection, principal component analysis and clustering. Previously, implementations of these uncertainty propagation methods have only been available as separate packages, written in different languages. Previous implementations have also suffered from being very costly to compute, and in the case of differential expression detection, have been limited in the experimental designs to which they can be applied. puma is a Bioconductor package incorporating a suite of analysis methods for use on Affymetrix GeneChip data. puma extends the differential expression detection methods of previous work from the 2-class case to the multi-factorial case. puma can be used to automatically create design and contrast matrices for typical experimental designs, which can be used both within the package itself but also in other Bioconductor packages. The implementation of differential expression detection methods has been parallelised leading to significant decreases in processing time on a range of computer architectures. puma incorporates the first R implementation of an uncertainty propagation version of principal component analysis, and an implementation of a clustering method based on uncertainty propagation. All of these techniques are brought together in a single, easy-to-use package with clear, task-based documentation. For the first time, the puma package makes a suite of uncertainty propagation methods available to a general audience. These methods can be used to improve results from more traditional analyses of microarray data. puma also offers improvements in terms of scope and speed of execution over previously available methods. puma is recommended for anyone working with the Affymetrix GeneChip platform for gene expression analysis and can also be applied more generally.

Adherence to Clinical Practice Guidelines during Dementia Work-Up in a Real-World Setting: A Study from the Registry of Dementias of Girona.

PubMed

Turró-Garriga, Oriol; Calvó-Perxas, Laia; Vilalta-Franch, Joan; Hernández-Ferrándiz, Marta; Flaqué, Margarita; Linares, Marta; Cullell, Marta; Gich, Jordi; Casas, Isabel; Perkal, Héctor; Garre-Olmo, Josep

2017-01-01

There are several position statements and clinical practice guidelines (CPG) for diagnosing dementia. Our aims were to evaluate the adherence to CPG among specialists in the 7 memory clinics included in the Registry of Dementias of Girona (ReDeGi), and to compare the results between 2007-2011 and 2012-2015. We also determined the time and number of visits required to achieve a diagnosis, the supplementary tests ordered, and the drugs prescribed according to dementia subtypes. Medical charts of a stratified random sample of 475 ReDeGi cases were reviewed. Basic dementia work-up was evaluated using as a reference evidence-based CPG. An Index of Adherence (AI) was calculated using the following items in the medical chart: cognitive symptomatology; functional disability evaluation; physical examination; neurological examination; psychiatric examination; brief cognitive examination; activities of daily living performance examination; blood test; structural neuroimaging (CT-scan or MRI). The mean AI to CPG among specialists was of 8.2 points, and it improved from 7.9 points in 2007-2011 to 8.5 points in 2012-2015 (Cohen's d = 0.46). A lower adherence was detected in the most severe cases. A dementia diagnosis required 3.5 visits, regardless of the subtype of dementia, although milder cases required more time, more visits, and more supplementary tests than severe cases. The adherence to CPG in the catchment area of the ReDeGi is high, and an epidemiological surveillance system such as the ReDeGi may help in improving it. Dementia guidelines should establish procedures adapted to clinical practice, with simplified recommendations for most severe cases.

Computational Material Processing in Microgravity

NASA Technical Reports Server (NTRS)

2005-01-01

Working with Professor David Matthiesen at Case Western Reserve University (CWRU) a computer model of the DPIMS (Diffusion Processes in Molten Semiconductors) space experiment was developed that is able to predict the thermal field, flow field and concentration profile within a molten germanium capillary under both ground-based and microgravity conditions as illustrated. These models are coupled with a novel nonlinear statistical methodology for estimating the diffusion coefficient from measured concentration values after a given time that yields a more accurate estimate than traditional methods. This code was integrated into a web-based application that has become a standard tool used by engineers in the Materials Science Department at CWRU.

The Nurse in the University: A History of University Education for South African Nurses: A Case Study of the University of the Witwatersrand

PubMed Central

Horwitz, Simonne

2011-01-01

This paper charts the history and debates surrounding the introduction of academic, university-based training of nurses in South Africa. This was a process that was drawn out over five decades, beginning in the late 1930s. For nurses, university training was an important part of a process of professionalization; however, for other members of the medical community, nursing was seen as being linked to women's service work. Using the case-study of the University of the Witwatersrand, one of South Africa's premier universities and the place in the country to offer a university-based nursing program, we argue that an historical understanding of the ways in which nursing education was integrated into the university system tells us a great deal about the professionalization of nursing. This paper also recognises, for the first time, the pioneers of this important process. PMID:21994840

Adequacy of TRMM satellite rainfall data in driving the SWAT modeling of Tiaoxi catchment (Taihu lake basin, China)

NASA Astrophysics Data System (ADS)

Li, Dan; Christakos, George; Ding, Xinxin; Wu, Jiaping

2018-01-01

Spatial rainfall data is an essential input to Distributed Hydrological Models (DHM), and a significant contributor to hydrological model uncertainty. Model uncertainty is higher when rain gauges are sparse, as is often the case in practice. Currently, satellite-based precipitation products increasingly provide an alternative means to ground-based rainfall estimates, in which case a rigorous product assessment is required before implementation. Accordingly, the twofold objective of this work paper was the real-world assessment of both (a) the Tropical Rainfall Measuring Mission (TRMM) rainfall product using gauge data, and (b) the TRMM product's role in forcing data for hydrologic simulations in the area of the Tiaoxi catchment (Taihu lake basin, China). The TRMM rainfall products used in this study are the Version-7 real-time 3B42RT and the post-real-time 3B42. It was found that the TRMM rainfall data showed a superior performance at the monthly and annual scales, fitting well with surface observation-based frequency rainfall distributions. The Nash-Sutcliffe Coefficient of Efficiency (NSCE) and the relative bias ratio (BIAS) were used to evaluate hydrologic model performance. The satisfactory performance of the monthly runoff simulations in the Tiaoxi study supports the view that the implementation of real-time 3B42RT allows considerable room for improvement. At the same time, post-real-time 3B42 can be a valuable tool of hydrologic modeling, water balance analysis, and basin water resource management, especially in developing countries or at remote locations in which rainfall gauges are scarce.

A novel spatial-temporal detection method of dim infrared moving small target

NASA Astrophysics Data System (ADS)

Chen, Zhong; Deng, Tao; Gao, Lei; Zhou, Heng; Luo, Song

2014-09-01

Moving small target detection under complex background in infrared image sequence is one of the major challenges of modern military in Early Warning Systems (EWS) and the use of Long-Range Strike (LRS). However, because of the low SNR and undulating background, the infrared moving small target detection is a difficult problem in a long time. To solve this problem, a novel spatial-temporal detection method based on bi-dimensional empirical mode decomposition (EMD) and time-domain difference is proposed in this paper. This method is downright self-data decomposition and do not rely on any transition kernel function, so it has a strong adaptive capacity. Firstly, we generalized the 1D EMD algorithm to the 2D case. In this process, the project has solved serial issues in 2D EMD, such as large amount of data operations, define and identify extrema in 2D case, and two-dimensional signal boundary corrosion. The EMD algorithm studied in this project can be well adapted to the automatic detection of small targets under low SNR and complex background. Secondly, considering the characteristics of moving target, we proposed an improved filtering method based on three-frame difference on basis of the original difference filtering in time-domain, which greatly improves the ability of anti-jamming algorithm. Finally, we proposed a new time-space fusion method based on a combined processing of 2D EMD and improved time-domain differential filtering. And, experimental results show that this method works well in infrared small moving target detection under low SNR and complex background.

a Simple Spatially Weighted Measure of Temporal Stability for Data with Limited Temporal Observations

NASA Astrophysics Data System (ADS)

Piburn, J.; Stewart, R.; Morton, A.

2017-10-01

Identifying erratic or unstable time-series is an area of interest to many fields. Recently, there have been successful developments towards this goal. These new developed methodologies however come from domains where it is typical to have several thousand or more temporal observations. This creates a challenge when attempting to apply these methodologies to time-series with much fewer temporal observations such as for socio-cultural understanding, a domain where a typical time series of interest might only consist of 20-30 annual observations. Most existing methodologies simply cannot say anything interesting with so few data points, yet researchers are still tasked to work within in the confines of the data. Recently a method for characterizing instability in a time series with limitedtemporal observations was published. This method, Attribute Stability Index (ASI), uses an approximate entropy based method tocharacterize a time series' instability. In this paper we propose an explicitly spatially weighted extension of the Attribute StabilityIndex. By including a mechanism to account for spatial autocorrelation, this work represents a novel approach for the characterizationof space-time instability. As a case study we explore national youth male unemployment across the world from 1991-2014.

Importance of a midterm time horizon for addressing ethical issues integral to nanobiotechnology.

PubMed

Khushf, George

2007-01-01

There is a consensus emerging on the importance of upstream ethical engagement in nanobiotechnology. Such a preventive ethic would anticipate downstream concerns that might arise and mitigate them as part of the research and development process. However, there is an unappreciated tension between the time horizon of upstream ethics and that assumed by most bioethical research. Current standards of high-quality research on ethical issues biases the research in favor of near-term, science-based, results-oriented work. A near-term focus would miss many of the important ethical issues integral to nanobiotechnology and undermine the goals integral to upstream ethical engagement. However, if we move to a far-term time horizon, the ethical debates tend to get too speculative and are no longer disciplined by existing research trajectories. This paper addresses the link between the midterm time horizon necessary for upstream ethics and the form, content, and style of ethical reflection. New paradigm cases, standards, and criteria will be needed for high-quality upstream ethics work in the area of nanobiotechnology.

Neuromuscular assessment in elderly workers with and without work related shoulder/neck trouble: the NEW-study design and physiological findings.

PubMed

Sjøgaard, G; Søgaard, K; Hermens, H J; Sandsjö, L; Läubli, T; Thorn, S; Vollenbroek-Hutten, M M R; Sell, L; Christensen, H; Klipstein, A; Kadefors, R; Merletti, R

2006-01-01

Musculoskeletal disorders in the neck and shoulder area are a major occupational concern in the European countries especially among elderly females. The aim was to assess these disorders based on quantitative EMG indicators and functional tests. 252 female computer users (45-68 years) were recruited from four European countries in two contrast groups: (1) 88 neck/shoulder (NS) cases reporting trouble in the neck and/or shoulder region for more than 30 days during the last year, and (2) 164 NS-controls reporting such trouble for no more than 7 days. Questionnaires, functional/clinical tests, and physiological recordings were performed in workplace related field studies. The results showed no differences in anthropometrics but NS-cases reported more strained head positions and more eye problems than controls. The psychosocial working factors were similar, although, NS-controls had slightly better scores on working conditions, general health, and vitality compared to cases. The NS-cases had lower maximal voluntary contraction (MVC) during shoulder elevation (mean (SD) 310 (122) N) compared to the controls (364 (122) N). During 30% MVC electromyography (EMGrms) in the trapezius muscle was lower in NS-cases (194 (105) muV) than in controls (256 (169) muV), while no differences were found regarding endurance time. Estimated conduction velocity was not different between NS-cases and -controls. Four functional computer tests were performed equally well by NS-cases and -controls, and the corresponding EMG variables also did not differ. A major finding in this large-scale epidemiological study is the significantly lower MVC in NS-cases compared with NS-controls together with lower EMGrms value at 30% MVC, while computer tasks were performed at similar relative muscle activation. The study was unable to reveal quantitative EMG indicators and functional tests that could objectively assess disorders in NS-cases.

Paid and unpaid work, and its relation to low back and neck/shoulder disorders among women.

PubMed

Josephson, Malin; Ahlberg, Gunnel; Härenstam, Annika; Svensson, Helena; Theorell, Töres; Wiktorin, Christina; Vingård, Eva

2003-01-01

The aim of the present study was to estimate the influence of total work hours, paid work in the labor market and unpaid work in the family domain, on care-seeking for low back and neck/shoulder disorders in the female population. The exposure assessments considered a typical working' day during the previous twelve months and were assessed by interviews and questionnaires; 704 cases and 984 referents were examined. The cases had sought professional care during the study period; the referents were randomly selected from the same source population. There was no increased relative risk for care-seeking for low back and neck/shoulder disorders for gainfully employed women compared to those not employed, or for full-time compared to part-time working women. At least 60 hours per week of paid work, or at least 40 hours per week of unpaid work, separately, indicated an increased relative risk for care-seeking. The present results did not strengthen the hypothesis that a high amount of hours of work is an independent risk factor for musculoskeletal disorders.

7 CFR 718.10 - Time limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... in this title for the performance of any act falls on a Saturday, Sunday, national holiday, State... open for the transaction of business during normal working hours, the time for taking required action shall be extended to the close of business on the next working day. Or in case the action required to be...

Implications on 1 + 1 D Tsunami Runup Modeling due to Time Features of the Earthquake Source

NASA Astrophysics Data System (ADS)

Fuentes, M.; Riquelme, S.; Ruiz, J.; Campos, J.

2018-02-01

The time characteristics of the seismic source are usually neglected in tsunami modeling, due to the difference in the time scale of both processes. Nonetheless, there are just a few analytical studies that intended to explain separately the role of the rise time and the rupture velocity. In this work, we extend an analytical 1 + 1 D solution for the shoreline motion time series, from the static case to the kinematic case, by including both rise time and rupture velocity. Our results show that the static case corresponds to a limit case of null rise time and infinite rupture velocity. Both parameters contribute in shifting the arrival time, but maximum runup may be affected by very slow ruptures and long rise time. Parametric analysis reveals that runup is strictly decreasing with the rise time while is highly amplified in a certain range of slow rupture velocities. For even lower rupture velocities, the tsunami excitation vanishes and for larger, quicker approaches to the instantaneous case.

Implications on 1 + 1 D Tsunami Runup Modeling due to Time Features of the Earthquake Source

NASA Astrophysics Data System (ADS)

Fuentes, M.; Riquelme, S.; Ruiz, J.; Campos, J.

2018-04-01

The time characteristics of the seismic source are usually neglected in tsunami modeling, due to the difference in the time scale of both processes. Nonetheless, there are just a few analytical studies that intended to explain separately the role of the rise time and the rupture velocity. In this work, we extend an analytical 1 + 1 D solution for the shoreline motion time series, from the static case to the kinematic case, by including both rise time and rupture velocity. Our results show that the static case corresponds to a limit case of null rise time and infinite rupture velocity. Both parameters contribute in shifting the arrival time, but maximum runup may be affected by very slow ruptures and long rise time. Parametric analysis reveals that runup is strictly decreasing with the rise time while is highly amplified in a certain range of slow rupture velocities. For even lower rupture velocities, the tsunami excitation vanishes and for larger, quicker approaches to the instantaneous case.

Retrospective analysis of operative treatment of a series of 100 patients with subdural hematoma.

PubMed

Godlewski, Bartosz; Pawelczyk, Agnieszka; Pawelczyk, Tomasz; Ceranowicz, Katarzyna; Wojdyn, Maciej; Radek, Maciej

2013-01-01

This retrospective study of medical records, surgical protocols, patient observation cards, and imaging files of 100 patients treated for subdural hematoma analyzed the type of hematoma, patient age and sex, operative technique, neurological status, cause of injury, duration of hospital stay, mortality rate, and the number of and reasons for reoperations to determine the effects on treatment outcomes. The time between the head injury and onset of neurological symptoms was analyzed versus the type of hematoma determined from computed tomography (CT) scans. Acute hematomas accounted for 38% of the cases, with subacute hematomas representing 20%, and chronic ones accounting for 42%. In trauma patients, the mean time interval between the injury and onset of neurological symptoms was 0.38 days for acute hematomas, 13.8 days for subacute hematomas, and 23.75 days for chronic hematomas. Repeat surgery was carried out in 26% of the cases. Improvement was obtained in 44% of cases, deterioration in 20%, and no change in neurological status in 36%. Timing of the operations was between 15:00 and 23:00 in 45%, between 23:00 and 7:00 in 33%, and between 7:00 and 15:00 in 22%. The classification of hematomas based on CT presentation corresponds to the classification based on the time elapsed between injury and onset of symptoms, and appears to be appropriate and useful in everyday practice. No preceding injury was identified in 31.6% of acute hematomas, 50% of subacute hematomas, and 61.9% of chronic hematomas. Analysis of reoperations indicates that trepanation may be superior to craniotomy as primary surgery for subacute and chronic hematomas. Subdural hematoma surgeries take place at all times of the day, with most carried out outside the usual working hours.

Using mobile phone text messaging for malaria surveillance in rural Kenya

PubMed Central

2014-01-01

Background Effective surveillance systems are required to track malaria testing and treatment practices. A 26-week study “SMS for Life” was piloted in five rural districts of Kenya to examine whether SMS reported surveillance data could ensure real-time visibility of accurate data and their use by district managers to impact on malaria case-management. Methods Health workers from 87 public health facilities used their personal mobile phones to send a weekly structured SMS text message reporting the counts of four basic surveillance data elements to a web-based system accessed by district managers. Longitudinal monitoring of SMS reported data through the web-based system and two rounds of cross-sectional health facility surveys were done to validate accuracy of data. Results Mean response rates were 96% with 87% of facilities reporting on time. Fifty-eight per cent of surveillance data parameters were accurately reported. Overall mean testing rates were 37% with minor weekly variations ranging from 32 to 45%. Overall test positivity rate was 24% (weekly range: 17-37%). Ratio of anti-malarial treatments to test positive cases was 1.7:1 (weekly range: 1.3:1–2.2:1). District specific trends showed fluctuating patterns in testing rates without notable improvement over time but the ratio of anti-malarial treatments to test positive cases improved over short periods of time in three out of five districts. Conclusions The study demonstrated the feasibility of using simple mobile phone text messages to transmit timely surveillance data from peripheral health facilities to higher levels. However, accuracy of data reported was suboptimal. Future work should focus on improving quality of SMS reported surveillance data. PMID:24642130

Use of operating room information system data to predict the impact of reducing turnover times on staffing costs.

PubMed

Dexter, Franklin; Abouleish, Amr E; Epstein, Richard H; Whitten, Charles W; Lubarsky, David A

2003-10-01

Potential benefits to reducing turnover times are both quantitative (e.g., complete more cases and reduce staffing costs) and qualitative (e.g., improve professional satisfaction). Analyses have shown the quantitative arguments to be unsound except for reducing staffing costs. We describe a methodology by which each surgical suite can use its own numbers to calculate its individual potential reduction in staffing costs from reducing its turnover times. Calculations estimate optimal allocated operating room (OR) time (based on maximizing OR efficiency) before and after reducing the maximum and average turnover times. At four academic tertiary hospitals, reductions in average turnover times of 3 to 9 min would result in 0.8% to 1.8% reductions in staffing cost. Reductions in average turnover times of 10 to 19 min would result in 2.5% to 4.0% reductions in staffing costs. These reductions in staffing cost are achieved predominantly by reducing allocated OR time, not by reducing the hours that staff work late. Heads of anesthesiology groups often serve on OR committees that are fixated on turnover times. Rather than having to argue based on scientific studies, this methodology provides the ability to show the specific quantitative effects (small decreases in staffing costs and allocated OR time) of reducing turnover time using a surgical suite's own data. Many anesthesiologists work at hospitals where surgeons and/or operating room (OR) committees focus repeatedly on turnover time reduction. We developed a methodology by which the reductions in staffing cost as a result of turnover time reduction can be calculated for each facility using its own data. Staffing cost reductions are generally very small and would be achieved predominantly by reducing allocated OR time to the surgeons.

The dim light melatonin onset following fixed and free sleep schedules.

PubMed

Burgess, Helen J; Eastman, Charmane I

2005-09-01

The time at which the dim light melatonin onset (DLMO) occurs can be used to ensure the correct timing of light and/or melatonin administration in order to produce desired circadian phase shifts. Sometimes however, measuring the DLMO is not feasible. Here we determined if the DLMO was best estimated from fixed sleep times (based on habitual sleep times) or free (ad libitum) sleep times. Young healthy sleepers on fixed (n=60) or free (n=60) sleep schedules slept at home for 6 days. Sleep times were recorded with sleep logs verified with wrist actigraphy. Half-hourly saliva samples were then collected during a dim light phase assessment and were later assayed to determine the DLMO. We found that the DLMO was more highly correlated with sleep times in the free sleepers than in the fixed sleepers (DLMO versus wake time, r=0.70 and r=0.44, both P<0.05). The regression equation between wake time and the DLMO in the free sleepers predicted the DLMO in an independent sample of free sleepers (n=23) to within 1.5 h of the actual DLMO in 96% of cases. These results indicate that the DLMO can be readily estimated in people whose sleep times are minimally affected by work, class and family commitments. Further work is necessary to determine if the DLMO can be accurately estimated in people with greater work and family responsibilities that affect their sleep times, perhaps by using weekend wake times, and if this method will apply to the elderly and patients with circadian rhythm disorders.

The dim light melatonin onset following fixed and free sleep schedules

PubMed Central

Burgess, Helen J.; Eastman, Charmane I.

2013-01-01

Summary The time at which the dim light melatonin onset (DLMO) occurs can be used to ensure the correct timing of light and/or melatonin administration in order to produce desired circadian phase shifts. Sometimes however, measuring the DLMO is not feasible. Here we determined if the DLMO was best estimated from fixed sleep times (based on habitual sleep times) or free (ad libitum) sleep times. Young healthy sleepers on fixed (n = 60) or free (n = 60) sleep schedules slept at home for 6 days. Sleep times were recorded with sleep logs verified with wrist actigraphy. Half-hourly saliva samples were then collected during a dim light phase assessment and were later assayed to determine the DLMO. We found that the DLMO was more highly correlated with sleep times in the free sleepers than in the fixed sleepers (DLMO versus wake time, r = 0.70 and r = 0.44, both P < 0.05). The regression equation between wake time and the DLMO in the free sleepers predicted the DLMO in an independent sample of free sleepers (n = 23) to within 1.5 h of the actual DLMO in 96% of cases. These results indicate that the DLMO can be readily estimated in people whose sleep times are minimally affected by work, class and family commitments. Further work is necessary to determine if the DLMO can be accurately estimated in people with greater work and family responsibilities that affect their sleep times, perhaps by using weekend wake times, and if this method will apply to the elderly and patients with circadian rhythm disorders. PMID:16120097

Better approximation guarantees for job-shop scheduling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldberg, L.A.; Paterson, M.; Srinivasan, A.

1997-06-01

Job-shop scheduling is a classical NP-hard problem. Shmoys, Stein & Wein presented the first polynomial-time approximation algorithm for this problem that has a good (polylogarithmic) approximation guarantee. We improve the approximation guarantee of their work, and present further improvements for some important NP-hard special cases of this problem (e.g., in the preemptive case where machines can suspend work on operations and later resume). We also present NC algorithms with improved approximation guarantees for some NP-hard special cases.

Using a Technology-Based Case to Aid in Improving Assessment

ERIC Educational Resources Information Center

Zelin, Robert C., II

2008-01-01

This paper describes how a technology-based case using Microsoft Access can aid in the assessment process. A case was used in lieu of giving a final examination in an Accounting Information Systems course. Students worked in small groups to design a database-driven payroll system for a hypothetical company. Each group submitted its results along…

COLLABORATE©: a universal competency-based paradigm for professional case management, Part III: key considerations for making the paradigm shift.

PubMed

Treiger, Teresa M; Fink-Samnick, Ellen

2014-01-01

The purpose of the third of this 3-article series is to provide context and justification for a new paradigm of case management built upon a value-driven foundation that * improves the patient's experience of health care delivery, * provides consistency in approach applicable across health care populations, and * optimizes the potential for return on investment. Applicable to all health care sectors where case management is practiced. In moving forward the one fact that rings true is there will be constant change in our industry. As the health care terrain shifts and new influences continually surface, there will be consequences for case management practice. These impacts require nimble clinical professionals in possession of recognized and firmly established competencies. They must be agile to frame (and reframe) their professional practice to facilitate the best possible outcomes for their patients. Case managers can choose to be Gumby or Pokey. This is exactly why the definition of a competency-based case management model's time has come, one sufficiently fluid to fit into any setting of care. The practice of case management transcends the vast array of representative professional disciplines and educational levels. A majority of current models are driven by business priorities rather than the competencies critical to successful practice and quality patient outcomes. This results in a fragmented professional case management identity. While there is inherent value in what each discipline brings to the table, this advanced model unifies behind case management's unique, strengths-based identity instead of continuing to align within traditional divisions (e.g., discipline, work setting, population served). This model fosters case management's expanding career advancement opportunities, including a reflective clinical ladder.

[Results of Training for Personnel Involved in Blood-Transfusion Testing Outside of Regular Work Hours at Saga University Hospital].

PubMed

Yamada, Marie; Yamada, Naotomo; Higashitani, Takanori; Ohta, Shoichiro; Sueoka, Eisaburo

2015-11-01

Laboratory testing prior to blood transfusion outside of regular hours in many hospitals and clinics is frequently conducted by technicians without sufficient experience in such testing work. To obtain consistent test results regardless of the degree of laboratory experience with blood transfusion testing, the number of facilities introducing automated equipment for testing prior to blood transfusion is increasing. Our hospital's blood transfusion department introduced fully automated test equipment in October of 2010 for use when blood transfusions are conducted outside of regular hours. However, excessive dependence on automated testing can lead to an inability to do manual blood typing or cross-match testing when necessitated by breakdowns in the automated test equipment, in the case of abnormal specimen reactions, or other such case. In addition, even outside of normal working hours there are more than a few instances in which transfusion must take place based on urgent communications from clinical staff, with the need for prompt and flexible timing of blood transfusion test and delivery of blood products. To address this situation, in 2010 we began training after-hours laboratory personnel in blood transfusion testing to provide practice using test tubes manually and to achieve greater understanding of blood transfusion test work (especially in cases of critical blood loss). Results of the training and difficulties in its implementation for such after-hours laboratory personnel at our hospital are presented and discussed in this paper. [Original

[The use of volunteers to support family carers of dementia patients: results of a prospective longitudinal study investigating expectations towards and experience with training and professional support].

PubMed

Grässel, E; Schirmer, B

2006-06-01

Caring for a dementia patient in the family often turns out to be a full-time job for family carers. So home visitors-for example volunteers spending time with the patient and thus offering some respite to the family-may be a very important aspect of stabilizing home care. This study investigates the expectations of volunteers concerning their training and their future voluntary work, as well as their visiting experiences, and their reasons for stopping the voluntary work. A total of 40 volunteers were interviewed three times over a 18 month period. The interviews were based on interview guidelines and were problem-centered. The interviewees' replies were subject to a summarizing qualitative content analysis. Of the study participants 85% were women, 48% had previously been family carers themselves, and 50% had previous experience of other voluntary work. Their wish "to do something useful" and "to learn more about dementia" were the main reasons for participation in voluntary work. The interviewed persons tend to learn most about communicating with dementia patients through case studies and practical exercises. Work pressures or restarting employment were the most common reasons to stop the voluntary work. Only if the volunteers are supported by professionals--particularly in the form of a contact person who is always available when problems occur--can this type of respite for family carers be maintained.

Work-family conflict and sleep disturbance: the Malaysian working women study.

PubMed

Aazami, Sanaz; Mozafari, Mosayeb; Shamsuddin, Khadijah; Akmal, Syaqirah

2016-01-01

This study aimed at assessing effect of the four dimensions of work-family conflicts (strain and time-based work interference into family and family interference into work) on sleep disturbance in Malaysian working women. This cross-sectional study was conducted among 325 Malaysian married working women. Multiple-stage simple random sampling method was used to recruit women from public service departments of Malaysia. Self-administrated questionnaires were used to measure the study variables and data were analyzed using SPSS version 21. We found that high level of the four dimensions of work-family conflicts significantly increase sleep disturbance. Our analyses also revealed an age-dependent effect of the work-family conflict on sleep disturbance. Women in their 20 to 30 yr old suffer from sleep disturbance due to high level of time-based and strain-based work-interference into family. However, the quality of sleep among women aged 30-39 were affected by strain-based family-interference into work. Finally, women older than 40 yr had significantly disturbed sleep due to strain-based work-interference into family as well as time-based family interference into work. Our findings showed that sleep quality of working women might be disturbed by experiencing high level of work-family conflict. However, the effects of inter-role conflicts on sleep varied among different age groups.

Using Geo-Data Corporately on the Response Phase of Emergency Management

NASA Astrophysics Data System (ADS)

Demir Ozbek, E.; Ates, S.; Aydinoglu, A. C.

2015-08-01

Response phase of emergency management is the most complex phase in the entire cycle because it requires cooperation between various actors relating to emergency sectors. A variety of geo-data is needed at the emergency response such as; existing data provided by different institutions and dynamic data collected by different sectors at the time of the disaster. Disaster event is managed according to elaborately defined activity-actor-task-geodata cycle. In this concept, every activity of emergency response is determined with Standard Operation Procedure that enables users to understand their tasks and required data in any activity. In this study, a general conceptual approach for disaster and emergency management system is developed based on the regulations to serve applications in Istanbul Governorship Provincial Disaster and Emergency Directorate. The approach is implemented to industrial facility explosion example. In preparation phase, optimum ambulance locations are determined according to general response time of the ambulance to all injury cases in addition to areas that have industrial fire risk. Management of the industrial fire case is organized according to defined actors, activities, and working cycle that describe required geo-data. A response scenario was prepared and performed for an industrial facility explosion event to exercise effective working cycle of actors. This scenario provides using geo-data corporately between different actors while required data for each task is defined to manage the industrial facility explosion event. Following developing web technologies, this scenario based approach can be effective to use geo-data on the web corporately.

Decontamination of chemical tracers in droplets by a submerging thin film flow

NASA Astrophysics Data System (ADS)

Landel, Julien R.; McEvoy, Harry; Dalziel, Stuart B.

2016-11-01

We investigate the decontamination of chemical tracers contained in small viscous drops by a submerging falling film. This problem has applications in the decontamination of hazardous chemicals, following accidental releases or terrorist attacks. Toxic droplets lying on surfaces are cleaned by spraying a liquid decontaminant over the surface. The decontaminant film submerges the droplets, without detaching them, in order to neutralize toxic chemicals in the droplets. The decontamination process is controlled by advection, diffusion and reaction processes near the drop-film interface. Chemical tracers dissolve into the film flow forming a thin diffusive boundary layer at the interface. The chemical tracers are then neutralized through a reaction with a chemical decontaminant transported in the film. We assume in this work that the decontamination process occurs mainly in the film phase owing to low solubility of the decontaminant in the drop phase. We analyze the impact of the reaction time scale, assuming first-order reaction, in relation with the characteristic advection and diffusion time scales in the case of a single droplet. Using theoretical, numerical and experimental means, we find that the reaction time scale need to be significantly smaller than the characteristic time scale in the diffusive boundary layer in order to enhance noticeably the decontamination of a single toxic droplet. We discuss these results in the more general case of the decontamination of a large number of droplets. This material is based upon work supported by the Defense Threat Reduction Agency under Contract No. HDTRA1-12-D-0003-0001.

Functional measures developed for clinical populations identified impairment among active workers with upper extremity disorders

PubMed Central

Gardner, Bethany T.; Dale, Ann Marie; Buckner-Petty, Skye; Rachford, Robert; Strickland, Jaime; Kaskutas, Vicki; Evanoff, Bradley

2017-01-01

Purpose Few studies have explored measures of function across a range of health outcomes in a general working population. Using four upper extremity (UE) case definitions from the scientific literature, we described the performance of functional measures of work, activities of daily living, and overall health. Methods A sample of 573 workers completed several functional measures: modified recall versions of the QuickDASH, Levine Functional Status Scale (FSS), DASH Work module (DASH-W), and standard SF-8 physical component score. We determined case status based on four UE case definitions: 1) UE symptoms, 2) UE musculoskeletal disorders (MSD), 3) carpal tunnel syndrome (CTS), and 4) work limitations due to UE symptoms. We calculated effect sizes for each case definition to show the magnitude of the differences that were detected between cases and non-cases for each case definition on each functional measure. Sensitivity and specificity analyses showed how well each measure identified functional impairments across the UE case definitions. Results All measures discriminated between cases and non-cases for each case definition with the largest effect sizes for CTS and work limitations, particularly for the modified FSS and DASH-W measures. Specificity was high and sensitivity was low for outcomes of UE symptoms and UE MSD in all measures. Sensitivity was high for CTS and work limitations. Conclusions Functional measures developed specifically for use in clinical, treatment-seeking populations may identify mild levels of impairment in relatively healthy, active working populations, but measures performed better among workers with CTS or those reporting limitations at work. PMID:26091980

Injuries and fatalities among emergency medical technicians and paramedics in the United States.

PubMed

Maguire, Brian J; Smith, Sean

2013-08-01

Emergency medical services personnel treat 22 million patients a year, yet little is known of their risk of injury and fatality. Work-related injury and fatality rates among US paramedics and emergency medical technicians (EMTs) are higher than the national average for all occupations. Data collected by the Department of Labor (DOL) Bureau of Labor Statistics were reviewed to identify injuries and fatalities among EMTs and paramedics from 2003 through 2007. The characteristics of fatal injuries are described and the rates and relative risks of the non-fatal injuries were calculated and compared to the national average. Of the 21,749 reported cases, 21,690 involved non-fatal injuries or illnesses that resulted in lost work days among EMTs and paramedics within the private sector. Of the injuries, 3,710 (17%) resulted in ≥31 days of lost work time. A total of 14,470 cases (67%) involved sprains or strains; back injury was reported in 9,290 of the cases (43%); and the patient was listed as the source of injury in 7,960 (37%) cases. The most common events were overexertion (12,146, 56%), falls (2,169, 10%), and transportation-related (1,940, 9%). A total of 530 assaults were reported during the study period. Forty-five percent of the cases occurred among females (females accounted for 27% of employment in this occupation during 2007). In 2007, EMTs and paramedics suffered 349.9 injuries with days away from work per 10,000 full-time workers, compared to an average of 122.2 for all private industry occupations (Relative risk = 2.9; 95% CI: 2.7-3.0). During the study period, 59 fatalities occurred among EMTs and paramedics in both the private industry and in the public sector. Of those fatalities, 51 (86%) were transportation-related and five (8%) were assaults; 33 (56%) were classified as "multiple traumatic injuries." Data from the DOL show that EMTs and paramedics have a rate of injury that is about three times the national average for all occupations. The vast majority of fatalities are secondary to transportation related-incidents. Assaults are also identified as a significant cause of fatality. The findings also indicate that females in this occupational group may have a disproportionately larger number of injuries. Support is recommended for further research related to causal factors and for the development, evaluation and promulgation of evidence-based interventions to mitigate this problem.

Deliberating Tarceva: A case study of how British NHS managers decide whether to purchase a high-cost drug in the shadow of NICE guidance.

PubMed

Hughes, David; Doheny, Shane

2011-11-01

This paper examines audio-recorded data from meetings in which NHS managers decide whether to fund high-cost drugs for individual patients. It investigates the work of a Welsh individual patient commissioning (IPC) panel responsible for sanctioning the purchase of 'un-commissioned' treatments for exceptional cases. The case study presented highlights the changing rationales used for approving or denying a cancer drug, Tarceva, during a period when NICE first suggested it was not cost effective, but then changed its position in a final technology appraisal recommending use when the cost did not exceed that of an alternative product. Our data show how decisions taken in the shadow of NICE guidance remain complex and subject to local discretion. Guidance that takes time to prepare, is released in stages, and relates to particular disease stages, must be interpreted in the context of particular cases. The case-based IPC panel discourse stands in tension with the standardised population-based recommendations in guidance. Panel members, who based their decisions on the central notions of 'efficacy' and 'exceptionality', often struggled to apply NICE information on cost-effectiveness to their deliberations on efficacy (clinical effectiveness). The case study suggests that the complex nature of decision making makes standardization of outcomes very difficult to achieve, so that local professional judgement is likely to remain central to health care rationing at this level. Copyright © 2011 Elsevier Ltd. All rights reserved.

Methods to recognize work-related cancer in workplaces, the general population, and by experts in the clinic, a Norwegian experience

PubMed Central

2011-01-01

Background In most countries, the numbers of work-related cancer identified are much lower than are the estimated total burden of cancer caused by exposure at work. Therefore, there is a great need to use all available practical as well as epidemiological methods for identification as well as to develop new methods of recognizing cases of work-related cancers. Methods Primarily based on practical experiences from Norway, methods to identify cases of possible work-related cancers in the general population and at workplaces as well as methods to recognize more specific cases after referral to specialized clinics are reviewed in this publication. Results Countries applying a number of the available methods to detect work-related cancer reach a reporting rate of 60 such cases per million, while other countries that do not employ such methods hardly identify any cases. As most subjects previously exposed to cancer causing agents and substances at work are gradually recruited out of work, methods should be versatile for identification of cases in the general population, as well as at work. Conclusions Even in countries using a number of the available methods for identification, only a limited fraction of the real number of work-related cancer are notified to the labour inspectorate. Clinicians should be familiar with the methods and do the best to identify work-related cancer to serve prevention. PMID:21899752

Improvement of Automated POST Case Success Rate Using Support Vector Machines

NASA Technical Reports Server (NTRS)

Zwack, Matthew R.; Dees, Patrick D.

2017-01-01

During early conceptual design of complex systems, concept down selection can have a large impact upon program life-cycle cost. Therefore, any concepts selected during early design will inherently commit program costs and affect the overall probability of program success. For this reason it is important to consider as large a design space as possible in order to better inform the down selection process. For conceptual design of launch vehicles, trajectory analysis and optimization often presents the largest obstacle to evaluating large trade spaces. This is due to the sensitivity of the trajectory discipline to changes in all other aspects of the vehicle design. Small deltas in the performance of other subsystems can result in relatively large fluctuations in the ascent trajectory because the solution space is non-linear and multi-modal [1]. In order to help capture large design spaces for new launch vehicles, the authors have performed previous work seeking to automate the execution of the industry standard tool, Program to Optimize Simulated Trajectories (POST). This work initially focused on implementation of analyst heuristics to enable closure of cases in an automated fashion, with the goal of applying the concepts of design of experiments (DOE) and surrogate modeling to enable near instantaneous throughput of vehicle cases [2]. Additional work was then completed to improve the DOE process by utilizing a graph theory based approach to connect similar design points [3]. The conclusion of the previous work illustrated the utility of the graph theory approach for completing a DOE through POST. However, this approach was still dependent upon the use of random repetitions to generate seed points for the graph. As noted in [3], only 8% of these random repetitions resulted in converged trajectories. This ultimately affects the ability of the random reps method to confidently approach the global optima for a given vehicle case in a reasonable amount of time. With only an 8% pass rate, tens or hundreds of thousands of reps may be needed to be confident that the best repetition is at least close to the global optima. However, typical design study time constraints require that fewer repetitions be attempted, sometimes resulting in seed points that have only a handful of successful completions. If a small number of successful repetitions are used to generate a seed point, the graph method may inherit some inaccuracies as it chains DOE cases from the non-global-optimal seed points. This creates inherent noise in the graph data, which can limit the accuracy of the resulting surrogate models. For this reason, the goal of this work is to improve the seed point generation method and ultimately the accuracy of the resulting POST surrogate model. The work focuses on increasing the case pass rate for seed point generation.

Two-Step Optimization for Spatial Accessibility Improvement: A Case Study of Health Care Planning in Rural China

PubMed Central

Luo, Jing; Tian, Lingling; Luo, Lei; Yi, Hong

2017-01-01

A recent advancement in location-allocation modeling formulates a two-step approach to a new problem of minimizing disparity of spatial accessibility. Our field work in a health care planning project in a rural county in China indicated that residents valued distance or travel time from the nearest hospital foremost and then considered quality of care including less waiting time as a secondary desirability. Based on the case study, this paper further clarifies the sequential decision-making approach, termed “two-step optimization for spatial accessibility improvement (2SO4SAI).” The first step is to find the best locations to site new facilities by emphasizing accessibility as proximity to the nearest facilities with several alternative objectives under consideration. The second step adjusts the capacities of facilities for minimal inequality in accessibility, where the measure of accessibility accounts for the match ratio of supply and demand and complex spatial interaction between them. The case study illustrates how the two-step optimization method improves both aspects of spatial accessibility for health care access in rural China. PMID:28484707

Two-Step Optimization for Spatial Accessibility Improvement: A Case Study of Health Care Planning in Rural China.

PubMed

Luo, Jing; Tian, Lingling; Luo, Lei; Yi, Hong; Wang, Fahui

2017-01-01

A recent advancement in location-allocation modeling formulates a two-step approach to a new problem of minimizing disparity of spatial accessibility. Our field work in a health care planning project in a rural county in China indicated that residents valued distance or travel time from the nearest hospital foremost and then considered quality of care including less waiting time as a secondary desirability. Based on the case study, this paper further clarifies the sequential decision-making approach, termed "two-step optimization for spatial accessibility improvement (2SO4SAI)." The first step is to find the best locations to site new facilities by emphasizing accessibility as proximity to the nearest facilities with several alternative objectives under consideration. The second step adjusts the capacities of facilities for minimal inequality in accessibility, where the measure of accessibility accounts for the match ratio of supply and demand and complex spatial interaction between them. The case study illustrates how the two-step optimization method improves both aspects of spatial accessibility for health care access in rural China.

A collective case study of nursing students with learning disabilities.

PubMed

Kolanko, Kathrine M

2003-01-01

This collective case study described the meaning of being a nursing student with a learning disability and examined how baccalaureate nursing students with learning disabilities experienced various aspects of the nursing program. It also examined how their disabilities and previous educational and personal experiences influenced the meaning that they gave to their educational experiences. Seven nursing students were interviewed, completed a demographic data form, and submitted various artifacts (test scores, evaluation reports, and curriculum-based material) for document analysis. The researcher used Stake's model for collective case study research and analysis (1). Data analysis revealed five themes: 1) struggle, 2) learning how to learn with LD, 3) issues concerning time, 4) social support, and 5) personal stories. Theme clusters and individual variations were identified for each theme. Document analysis revealed that participants had average to above average intellectual functioning with an ability-achievement discrepancy among standardized test scores. Participants noted that direct instruction, structure, consistency, clear directions, organization, and a positive instructor attitude assisted learning. Anxiety, social isolation from peers, and limited time to process and complete work were problems faced by the participants.

Combining Adaptive Hypermedia with Project and Case-Based Learning

ERIC Educational Resources Information Center

Papanikolaou, Kyparisia; Grigoriadou, Maria

2009-01-01

In this article we investigate the design of educational hypermedia based on constructivist learning theories. According to the principles of project and case-based learning we present the design rational of an Adaptive Educational Hypermedia system prototype named MyProject; learners working with MyProject undertake a project and the system…

Mature vs. Active Deep-Seated Landslides: A Comparison Through Two Case Histories in the Alps

NASA Astrophysics Data System (ADS)

Delle Piane, Luca; Perello, Paolo; Baietto, Alessandro; Giorza, Alessandra; Musso, Alessia; Gabriele, Piercarlo; Baster, Ira

2016-06-01

Two case histories are presented, concerning the still poorly known alpine deep-seated gravitational slope deformations (DSD) located nearby Lanzada (central Italian Alps), and Sarre (north-western Italian Alps). The Lanzada DSD is a constantly monitored, juvenile, and active phenomenon, partly affecting an existing hydropower plant. Its well-developed landforms allow a precise field characterization of the instability-affected area. The Sarre DSD is a mature, strongly remodeled phenomenon, where the only hazard factor is represented by secondary instability processes at the base of the slope. In this case, the remodeling imposed the adoption of complementary analytical techniques to support the field work. The two presented studies had to be adapted to external factors, namely (a) available information, (b) geological and geomorphological setting, and (c) final scope of the work. The Lanzada case essentially relied upon accurate field work; the Sarre case was mostly based on digital image and DTM processing. In both cases a sound field structural analysis formed the necessary background to understand the mechanisms leading to instability. A back-analysis of the differences between the study methods adopted in the two cases is finally presented, leading to suggestions for further investigations and design.

Evaluation of the environmental impact of Brownfield remediation options: comparison of two life cycle assessment-based evaluation tools.

PubMed

Cappuyns, Valérie; Kessen, Bram

2012-01-01

The choice between different options for the remediation of a contaminated site traditionally relies on economical, technical and regulatory criteria without consideration of the environmental impact of the soil remediation process itself. In the present study, the environmental impact assessment of two potential soil remediation techniques (excavation and off-site cleaning and in situ steam extraction) was performed using two life cycle assessment (LCA)-based evaluation tools, namely the REC (risk reduction, environmental merit and cost) method and the ReCiPe method. The comparison and evaluation of the different tools used to estimate the environmental impact of Brownfield remediation was based on a case study which consisted of the remediation of a former oil and fat processing plant. For the environmental impact assessment, both the REC and ReCiPe methods result in a single score for the environmental impact of the soil remediation process and allow the same conclusion to be drawn: excavation and off-site cleaning has a more pronounced environmental impact than in situ soil remediation by means of steam extraction. The ReCiPe method takes into account more impact categories, but is also more complex to work with and needs more input data. Within the routine evaluation of soil remediation alternatives, a detailed LCA evaluation will often be too time consuming and costly and the estimation of the environmental impact with the REC method will in most cases be sufficient. The case study worked out in this paper wants to provide a basis for a more sounded selection of soil remediation technologies based on a more detailed assessment of the secondary impact of soil remediation.

Investigation of crew performance in a multi-vehicle supervisory control task

NASA Technical Reports Server (NTRS)

Miller, R. A.; Plamondon, B. D.; Jagacinski, R. J.; Kirlik, A. C.

1986-01-01

Crew information processing and decision making in a supervisory control task which is loosely based on the mission of future generation helicopters is measured and represented. Subjects control the motion and activities of their own vehicle and direct the activities of four additional craft. The task involves searching an uncertain environment for cargo and enemies, returning cargo to home base and destroying enemies while attempting to avoid destruction of the scout and the supervised vehicles. A series of experiments with two-person crews and one-person crews were performed. Resulting crew performance was modeled with the objective of describing and understanding the information processing strategies utilized. Of particular interest are problem simplification strategies under time stress and high work load, simplification and compensation in the one-person cases, crew coordination in the two-person cases, and the relationship between strategy and errors in all cases. The results should provide some insight into the effective use of aids, particularly aids based on artificial intelligence, for similar tasks. The simulation is described which is used for the study and some preliminary results from the first two-person crew study are discussed.

Dynamic mesh adaptation for front evolution using discontinuous Galerkin based weighted condition number relaxation

DOE PAGES

Greene, Patrick T.; Schofield, Samuel P.; Nourgaliev, Robert

2017-01-27

A new mesh smoothing method designed to cluster cells near a dynamically evolving interface is presented. The method is based on weighted condition number mesh relaxation with the weight function computed from a level set representation of the interface. The weight function is expressed as a Taylor series based discontinuous Galerkin projection, which makes the computation of the derivatives of the weight function needed during the condition number optimization process a trivial matter. For cases when a level set is not available, a fast method for generating a low-order level set from discrete cell-centered fields, such as a volume fractionmore » or index function, is provided. Results show that the low-order level set works equally well as the actual level set for mesh smoothing. Meshes generated for a number of interface geometries are presented, including cases with multiple level sets. Lastly, dynamic cases with moving interfaces show the new method is capable of maintaining a desired resolution near the interface with an acceptable number of relaxation iterations per time step, which demonstrates the method's potential to be used as a mesh relaxer for arbitrary Lagrangian Eulerian (ALE) methods.« less

Flash floods warning technique based on wireless communication networks data

NASA Astrophysics Data System (ADS)

David, Noam; Alpert, Pinhas; Messer, Hagit

2010-05-01

Flash floods can occur throughout or subsequent to rainfall events, particularly in cases where the precipitation is of high-intensity. Unfortunately, each year these floods cause severe property damage and heavy casualties. At present, there are no sufficient real time flash flood warning facilities found to cope with this phenomenon. Here we show the tremendous potential of flash floods advanced warning based on precipitation measurements of commercial microwave links. As was recently shown, wireless communication networks supply high resolution precipitation measurements at ground level while often being situated in flood prone areas, covering large parts of these hazardous regions. We present the flash flood warning potential of the wireless communication system for two different cases when floods occurred at the Judean desert and at the northern Negev in Israel. In both cases, an advanced warning regarding the hazard could have been announced based on this system. • This research was supported by THE ISRAEL SCIENCE FOUNDATION (grant No. 173/08). This work was also supported by a grant from the Yeshaya Horowitz Association, Jerusalem. Additional support was given by the PROCEMA-BMBF project and by the GLOWA-JR BMBF project.

10 CFR 2.649 - Partial decisions on limited work authorization.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Certain Utilization Facilities; and Advance Issuance of Limited Work Authorizations Phased Applications... same time as in the case of a full decision relating to the issuance of a construction permit or...

Implications on 1+1 D runup modeling due to time features of the earthquake source

NASA Astrophysics Data System (ADS)

Fuentes, M.; Riquelme, S.; Campos, J. A.

2017-12-01

The time characteristics of the seismic source are usually neglected in tsunami modeling, due to the difference in the time scale of both processes. Nonetheless, there are just a few analytical studies that intended to explain separately the role of the rise time and the rupture velocity. In this work, we extend an analytical 1+1D solution for the shoreline motion time series, from the static case to the dynamic case, by including both, rise time and rupture velocity. Results show that the static case correspond to a limit case of null rise time and infinite rupture velocity. Both parameters contribute in shifting the arrival time, but maximum run-up may be affected by very slow ruptures and long rise time. The analytical solution has been tested for the Nicaraguan tsunami earthquake, suggesting that the rupture was not slow enough to cause wave amplification to explain the high runup observations.

Case control study of neuroblastoma in west-Germany after the Chernobyl accident.

PubMed

Michaelis, J; Haaf, H G; Zöllner, J; Kaatsch, P; Krummenauer, F; Berthold, F

1996-01-01

To explore possible causes of a 1988 incidence peak of infant neuroblastoma in west German regions which were contaminated with more than 6000 Bq/m2 Cs137 from the Chernobyl accident. The primary working hypothesis was that parents of the diseased children had been contaminated by an excessive intake of locally produced food, especially mushrooms or deer. Case control study with 1:2 (cases:controls) matching. Data were collected from the children's parents by questionnaires and telephone interviews. Nation-wide study (former FRG) based on the German Childhood Cancer Registry. Cases born in 1988 and reported with a neuroblastoma to the registry until March 1992. Population-based healthy controls, matched for age, sex and residence at time of diagnosis. The working hypothesis could not be confirmed by the study, because the parents of cases tended to eat less locally grown food than the parents of controls (RR = 0.63, 95% CI:0.20-1.97). Possible influence factors which previously have been described to be associated with neuroblastoma incidence could not be confirmed by the study. Parental exposure to herbicides and pesticides was associated with the occurrence of neuroblastoma (RR = 4.2, 95% CI:1.4-12.9). Neuroblastoma stage distribution in the contaminated regions was shifted towards lower stages as compared to the less contaminated regions and previous age cohorts. The study does not show additional evidence that the observed increase in neuroblastoma incidence might have been caused by exposure to fallout from the Chernobyl accident. The observed shift towards lower clinical stages may rather indicate increased diagnostic awareness. The association between neuroblastoma and parental exposure with herbicides and pesticides resulted from an extensive exploratory data analysis and needs to be confirmed in further studies.

Quantum fluctuation theorems and power measurements

NASA Astrophysics Data System (ADS)

Prasanna Venkatesh, B.; Watanabe, Gentaro; Talkner, Peter

2015-07-01

Work in the paradigm of the quantum fluctuation theorems of Crooks and Jarzynski is determined by projective measurements of energy at the beginning and end of the force protocol. In analogy to classical systems, we consider an alternative definition of work given by the integral of the supplied power determined by integrating up the results of repeated measurements of the instantaneous power during the force protocol. We observe that such a definition of work, in spite of taking account of the process dependence, has different possible values and statistics from the work determined by the conventional two energy measurement approach (TEMA). In the limit of many projective measurements of power, the system’s dynamics is frozen in the power measurement basis due to the quantum Zeno effect leading to statistics only trivially dependent on the force protocol. In general the Jarzynski relation is not satisfied except for the case when the instantaneous power operator commutes with the total Hamiltonian at all times. We also consider properties of the joint statistics of power-based definition of work and TEMA work in protocols where both values are determined. This allows us to quantify their correlations. Relaxing the projective measurement condition, weak continuous measurements of power are considered within the stochastic master equation formalism. Even in this scenario the power-based work statistics is in general not able to reproduce qualitative features of the TEMA work statistics.

The relationship between worker, occupational and workplace characteristics and whether an injury requires time off work: a matched case-control analysis in Ontario, Canada.

PubMed

Smith, Peter; Chen, Cynthia; Mustard, Cameron; Hogg-Johnson, Sheilah; Tompa, Emile

2015-04-01

The objective of this study was to examine individual, occupational, and workplace level factors associated with time loss following a similar injury. Seven thousand three hundred and forty-eight workers' compensation claims that did not require time off work were matched with up to four claims that required time off work on the event, nature, and part of body injured as well as injury year. Conditional logistic regression models examined individual, occupational, and workplace level factors that were associated with the likelihood of not requiring time off work. Employees from firms with higher premium rates were more likely to report no time loss from work and workers in more physically demanding occupations were less likely to report no time loss from work. We observed no association between age or gender and the probability of a time loss claim submission. Our results suggest that insurance costs are an incentive for workplaces to adopt policies and practices that minimize time loss following a work injury. © 2015 Wiley Periodicals, Inc.

Shared Goal Setting in Team-Based Geriatric Oncology

PubMed Central

Wallace, James; Canin, Beverly; Chow, Selina; Dale, William; Mohile, Supriya G.; Hamel, Lauren M.

2016-01-01

We present the case of a 92-year-old man, MH, who was given a diagnosis of colorectal cancer. His primary care physician, surgeon, geriatric oncologist, and family members all played important roles in his care. MH’s case is an example of a lack of explicit shared goal setting by the health care providers with the patient and family members and how that impeded care planning and health. This case demonstrates the importance of explicitly discussing and establishing shared goals in team-based cancer care delivery early on and throughout the care process, especially for older adults. Each individual member’s goals should be understood as they fit within the overarching shared team goals. We emphasize that shared goal setting and alignment of individual goals is a dynamic process that must occur several times at critical decision points throughout a patient’s care continuum. Providers and researchers can use this illustrative case to consider their own work and contemplate how shared goal setting can improve patient-centered care and health outcomes in various team-based care settings. Shared goal setting among team members has been demonstrated to improve outcomes in other contexts. However, we stress, that little investigation into the impact of shared goal setting on team-based cancer care delivery has been conducted. We list immediate research goals within team-based cancer care delivery that can provide a foundation for the understanding of the process and outcomes of shared goal setting. PMID:27624949

TASS Model Application for Testing the TDWAP Model

NASA Technical Reports Server (NTRS)

Switzer, George F.

2009-01-01

One of the operational modes of the Terminal Area Simulation System (TASS) model simulates the three-dimensional interaction of wake vortices within turbulent domains in the presence of thermal stratification. The model allows the investigation of turbulence and stratification on vortex transport and decay. The model simulations for this work all assumed fully-periodic boundary conditions to remove the effects from any surface interaction. During the Base Period of this contract, NWRA completed generation of these datasets but only presented analysis for the neutral stratification runs of that set (Task 3.4.1). Phase 1 work began with the analysis of the remaining stratification datasets, and in the analysis we discovered discrepancies with the vortex time to link predictions. This finding necessitated investigating the source of the anomaly, and we found a problem with the background turbulence. Using the most up to date version TASS with some important defect fixes, we regenerated a larger turbulence domain, and verified the vortex time to link with a few cases before proceeding to regenerate the entire 25 case set (Task 3.4.2). The effort of Phase 2 (Task 3.4.3) concentrated on analysis of several scenarios investigating the effects of closely spaced aircraft. The objective was to quantify the minimum aircraft separations necessary to avoid vortex interactions between neighboring aircraft. The results consist of spreadsheets of wake data and presentation figures prepared for NASA technical exchanges. For these formation cases, NASA carried out the actual TASS simulations and NWRA performed the analysis of the results by making animations, line plots, and other presentation figures. This report contains the description of the work performed during this final phase of the contract, the analysis procedures adopted, and sample plots of the results from the analysis performed.

It's the nature of the work: examining behavior-based sources of work-family conflict across occupations.

PubMed

Dierdorff, Erich C; Ellington, J Kemp

2008-07-01

The consequences of work-family conflict for both individuals and organizations have been well documented, and the various sources of such conflict have received substantial attention. However, the vast majority of extant research has focused on only time- and strain-based sources, largely neglecting behavior-based sources. Integrating two nationally representative databases, the authors examine 3 behavior-based antecedents of work-family conflict linked specifically to occupational work role requirements (interdependence, responsibility for others, and interpersonal conflict). Results from multilevel analysis indicate that significant variance in work-family conflict is attributable to the occupation in which someone works. Interdependence and responsibility for others predict work-family conflict, even after controlling for several time- and strain-based sources.

Making a Case for a Blended Approach: The Need for The Design-Based Case Study

ERIC Educational Resources Information Center

Deaton, Cynthia C. M.; Malloy, Jacquelynn A.

2017-01-01

Design-based case studies address research questions that involve instructional innovations within a bounded system. This blend of case study and design-based research provides a systematic approach to examining instructional innovations that are bounded by perspective, context, and time. Design-based case studies provide a framework for engaging…

Monitoring road safety development at regional level: A case study in the ASEAN region.

PubMed

Chen, Faan; Wang, Jianjun; Wu, Jiaorong; Chen, Xiaohong; Zegras, P Christopher

2017-09-01

Persistent monitoring of progress, evaluating the results of interventions and recalibrating to achieve continuous improvement over time is widely recognized as being crucial towards the successful development of road safety. In the ASEAN (Association of Southeast Asian Nations) region there is a lack of well-resourced teams that contain multidisciplinary safety professionals, and specialists in individual countries, who are able to carry out this work effectively. In this context, not only must the monitoring framework be effective, it must also be easy to use and adapt. This paper provides a case study that can be easily reproduced; based on an updated and refined Road Safety Development Index (RSDI), by means of the RSR (Rank-sum ratio)-based model, for monitoring/reporting road safety development at regional level. The case study was focused on the road safety achievements in eleven Southeast Asian countries; identifying the areas of poor performance, potential problems and delays. These countries are finally grouped into several classes based on an overview of their progress and achievements regarding to road safety. The results allow the policymakers to better understand their own road safety progress toward their desired impact; more importantly, these results enable necessary interventions to be made in a quick and timely manner. Keeping action plans on schedule if things are not progressing as desired. This would avoid 'reinventing the wheel' and trial and error approaches to road safety, making the implementation of action plans more effective. Copyright © 2017 Elsevier Ltd. All rights reserved.

Office-based endoscopic revision using a microdebrider for failed endoscopic dacryocystorhinostomy.

PubMed

Park, Jongyeop; Kim, Hochang

2016-12-01

This article is to introduce office-based endoscopic revision surgery using a microdebrider for failed endoscopic dacryocystorhinostomy (EN-DCR). The authors conducted retrospective, non-comparative, interventional case series analysis of 27 eyes of 24 patients, treated by office-based revision EN-DCR using a microdebrider. After local anesthesia, anatomical failures (cicatrization, granuloma, synechia) after primary EN-DCR were treated with a microdebrider (Osseoduo 120, Bien-Air Surgery, Le Noirmont, Switzerland) in an office setting, and a bicanalicular silicone tube was placed. Anatomical improvement and functional relief of epiphora were evaluated at 6-months after revision. The causes of failed EN-DCR were rhinostomy site cicatrization (17/27, 63.0 %), granulomatous obstruction (7/27, 25.9 %) and synechial formation (3/27, 11.1 %). The anatomical success rate was 100 %, and 85.2 % cases achieved complete relief of epiphora. The surgery did not exceed 10 min in any case and no complications were observed. Office-based revision EN-DCR using a microdebrider provided prompt management of post-DCR epiphora. The portable nature and all-round ability of the microdebrider allowed office-based surgery, which offered advantage to work with the surgeon's own well-trained office staff. Office-based revision EN-DCR can be both time- and money-saving, and might be regarded the treatment of choice for failed EN-DCR.

The impact of ergonomic work environment exposures on the risk of disability pension: Prospective results from DWECS/DREAM.

PubMed

Labriola, Merete; Feveile, Helene; Christensen, Karl B; Strøyer, Jesper; Lund, Thomas

2009-11-01

The objectives were to identify the impact of ergonomic work environment exposures on the risk of disability pension. A representative sample of 8475 employees of the total working population in Denmark were interviewed regarding work environment exposures and followed in a national register with data on granted disability pension. For women, approximately 34% of the disability pension cases were attributable to ergonomic work environment exposures. For men, 21% of the disability pension cases were attributable to ergonomic work environment. Ergonomic work environment, especially physically demanding work, working with hands lifted and repetitive work, are areas of intervention at the workplace that can facilitate and prolong labour market participation. The study provides estimates for the association between ergonomic exposures at work and administrative, cost-related measures of work disability in a large population-based longitudinal cohort study over 14 years. Approximately 21% for men and 34% for women of the disability pension cases were attributable to ergonomic work environment exposures.

Discussion Material for Small Unit Leaders: Issues of Garrison Ethics and Leadership

DTIC Science & Technology

2009-01-01

Fraud………………………....8 Case 4. Surrogate Parenting; Honor; Fraud……………………………..10 Case 5. Alcohol Use /Abuse; Sexual Harassment…………………………12 Case 6...Manual. 11 Case 5. Alcohol use /abuse; Sexual Harassment You are an instructor at a SNCO academy. You work with another...his eyes are often glassy and he keeps a large bottle of mouthwash in his desk. Several times, when working late, he was giddy and his breath smelled

A continuum mechanics-based musculo-mechanical model for esophageal transport

NASA Astrophysics Data System (ADS)

Kou, Wenjun; Griffith, Boyce E.; Pandolfino, John E.; Kahrilas, Peter J.; Patankar, Neelesh A.

2017-11-01

In this work, we extend our previous esophageal transport model using an immersed boundary (IB) method with discrete fiber-based structural model, to one using a continuum mechanics-based model that is approximated based on finite elements (IB-FE). To deal with the leakage of flow when the Lagrangian mesh becomes coarser than the fluid mesh, we employ adaptive interaction quadrature points to deal with Lagrangian-Eulerian interaction equations based on a previous work (Griffith and Luo [1]). In particular, we introduce a new anisotropic adaptive interaction quadrature rule. The new rule permits us to vary the interaction quadrature points not only at each time-step and element but also at different orientations per element. This helps to avoid the leakage issue without sacrificing the computational efficiency and accuracy in dealing with the interaction equations. For the material model, we extend our previous fiber-based model to a continuum-based model. We present formulations for general fiber-reinforced material models in the IB-FE framework. The new material model can handle non-linear elasticity and fiber-matrix interactions, and thus permits us to consider more realistic material behavior of biological tissues. To validate our method, we first study a case in which a three-dimensional short tube is dilated. Results on the pressure-displacement relationship and the stress distribution matches very well with those obtained from the implicit FE method. We remark that in our IB-FE case, the three-dimensional tube undergoes a very large deformation and the Lagrangian mesh-size becomes about 6 times of Eulerian mesh-size in the circumferential orientation. To validate the performance of the method in handling fiber-matrix material models, we perform a second study on dilating a long fiber-reinforced tube. Errors are small when we compare numerical solutions with analytical solutions. The technique is then applied to the problem of esophageal transport. We use two fiber-reinforced models for the esophageal tissue: a bi-linear model and an exponential model. We present three cases on esophageal transport that differ in the material model and the muscle fiber architecture. The overall transport features are consistent with those observed from the previous model. We remark that the continuum-based model can handle more realistic and complicated material behavior. This is demonstrated in our third case where a spatially varying fiber architecture is included based on experimental study. We find that this unique muscle fiber architecture could generate a so-called pressure transition zone, which is a luminal pressure pattern that is of clinical interest. This suggests an important role of muscle fiber architecture in esophageal transport.

Under-reporting of work-related disorders in the workplace: a case study and review of the literature.

PubMed

Pransky, G; Snyder, T; Dembe, A; Himmelstein, J

1999-01-01

Accurate reporting of work-related conditions is necessary to monitor workplace health and safety, and to identify the interventions that are most needed. Reporting systems may be designed primarily for external agencies (OSHA or workers' compensation) or for the employer's own use. Under-reporting of workplace injuries and illnesses is common due to a variety of causes and influences. Based on previous reports, the authors were especially interested in the role of safety incentive programmes on under-reporting. Safety incentive programmes typically reward supervisors and employees for reducing workplace injury rates, and thus may unintentionally inhibit proper reporting. The authors describe a case study of several industrial facilities in order to illustrate the extent of under-reporting and the reasons for its occurrence. A questionnaire and interview survey was administered to 110 workers performing similar tasks and several managers, health, and safety personnel at each of three industrial facilities. Although less than 5% of workers had officially reported a work-related injury or illness during the past year, over 85% experienced work-related symptoms, 50% had persistent work-related problems, and 30% reported either lost time from work or work restrictions because of their ailment. Workers described several reasons for not reporting their injuries, including fear of reprisal, a belief that pain was an ordinary consequence of work activity or ageing, lack of management responsiveness after prior reports, and a desire not to lose their usual job. Interviews with management representatives revealed administrative and other barriers to reporting, stemming from their desire to attain a goal of no reported injuries, and misconceptions about requirements for recordability. The corporate and facility safety incentives appeared to have an indirect, but significant negative influence on the proper reporting of workplace injuries by workers. A variety of influences may contribute to under-reporting; because of under-reporting, worker surveys and symptom reports may provide more valuable and timely information on risks than recordable injury logs. Safety incentive programmes should be carefully designed to ensure that they provide a stimulus for safety-related changes, and to discourage under-reporting. A case-control study of similar establishments, or data before and after instituting safety incentives, would be required to more clearly establish the role of these programmes in under-reporting.

Estimating Ocean Currents from Automatic Identification System Based Ship Drift Measurements

NASA Astrophysics Data System (ADS)

Jakub, Thomas D.

Ship drift is a technique that has been used over the last century and a half to estimate ocean currents. Several of the shortcomings of the ship drift technique include obtaining the data from multiple ships, the time delay in getting those ship positions to a data center for processing and the limited resolution based on the amount of time between position measurements. These shortcomings can be overcome through the use of the Automatic Identification System (AIS). AIS enables more precise ocean current estimates, the option of finer resolution and more timely estimates. In this work, a demonstration of the use of AIS to compute ocean currents is performed. A corresponding error and sensitivity analysis is performed to help identify under which conditions errors will be smaller. A case study in San Francisco Bay with constant AIS message updates was compared against high frequency radar and demonstrated ocean current magnitude residuals of 19 cm/s for ship tracks in a high signal to noise environment. These ship tracks were only minutes long compared to the normally 12 to 24 hour ship tracks. The Gulf of Mexico case study demonstrated the ability to estimate ocean currents over longer baselines and identified the dependency of the estimates on the accuracy of time measurements. Ultimately, AIS measurements when combined with ship drift can provide another method of estimating ocean currents, particularly when other measurements techniques are not available.

Damage detection methodology on beam-like structures based on combined modal Wavelet Transform strategy

NASA Astrophysics Data System (ADS)

Serra, Roger; Lopez, Lautaro

2018-05-01

Different approaches on the detection of damages based on dynamic measurement of structures have appeared in the last decades. They were based, amongst others, on changes in natural frequencies, modal curvatures, strain energy or flexibility. Wavelet analysis has also been used to detect the abnormalities on modal shapes induced by damages. However the majority of previous work was made with non-corrupted by noise signals. Moreover, the damage influence for each mode shape was studied separately. This paper proposes a new methodology based on combined modal wavelet transform strategy to cope with noisy signals, while at the same time, able to extract the relevant information from each mode shape. The proposed methodology will be then compared with the most frequently used and wide-studied methods from the bibliography. To evaluate the performance of each method, their capacity to detect and localize damage will be analyzed in different cases. The comparison will be done by simulating the oscillations of a cantilever steel beam with and without defect as a numerical case. The proposed methodology proved to outperform classical methods in terms of noisy signals.

Novel deletions involving the USH2A gene in patients with Usher syndrome and retinitis pigmentosa.

PubMed

García-García, Gema; Aller, Elena; Jaijo, Teresa; Aparisi, Maria J; Larrieu, Lise; Faugère, Valérie; Blanco-Kelly, Fiona; Ayuso, Carmen; Roux, Anne-Francoise; Millán, José M

2014-01-01

The aim of the present work was to identify and characterize large rearrangements involving the USH2A gene in patients with Usher syndrome and nonsyndromic retinitis pigmentosa. The multiplex ligation-dependent probe amplification (MLPA) technique combined with a customized array-based comparative genomic hybridization (aCGH) analysis was applied to 40 unrelated patients previously screened for point mutations in the USH2A gene in which none or only one pathologic mutation was identified. We detected six large deletions involving USH2A in six out of the 40 cases studied. Three of the patients were homozygous for the deletion, and the remaining three were compound heterozygous with a previously identified USH2A point mutation. In five of these cases, the patients displayed Usher type 2, and the remaining case displayed nonsyndromic retinitis pigmentosa. The exact breakpoint junctions of the deletions found in USH2A in four of these cases were characterized. Our study highlights the need to develop improved efficient strategies of mutation screening based upon next generation sequencing (NGS) that reduce cost, time, and complexity and allow simultaneous identification of all types of disease-causing mutations in diagnostic procedures.

Work-based resources as moderators of the relationship between work hours and satisfaction with work-family balance.

PubMed

Valcour, Monique

2007-11-01

This study reports an investigation of the relationships of work hours, job complexity, and control over work time to satisfaction with work-family balance. Based on data from a sample of 570 telephone call center representatives, a moderated hierarchical regression analysis revealed that work hours were negatively related to satisfaction with work-family balance, consistent with the resource drain perspective. Job complexity and control over work time were positively associated with satisfaction with work-family balance. Control over work time moderated the relationship such that as work hours rose, workers with low control experienced a decline in work-family balance satisfaction, while workers with high control did not. Results encourage greater research attention to work characteristics, such as job complexity and control over work time, and skills that represent resources useful to the successful integration of work and family demands. (c) 2007 APA

Application of seemingly unrelated regression in medical data with intermittently observed time-dependent covariates.

PubMed

Keshavarzi, Sareh; Ayatollahi, Seyyed Mohammad Taghi; Zare, Najaf; Pakfetrat, Maryam

2012-01-01

BACKGROUND. In many studies with longitudinal data, time-dependent covariates can only be measured intermittently (not at all observation times), and this presents difficulties for standard statistical analyses. This situation is common in medical studies, and methods that deal with this challenge would be useful. METHODS. In this study, we performed the seemingly unrelated regression (SUR) based models, with respect to each observation time in longitudinal data with intermittently observed time-dependent covariates and further compared these models with mixed-effect regression models (MRMs) under three classic imputation procedures. Simulation studies were performed to compare the sample size properties of the estimated coefficients for different modeling choices. RESULTS. In general, the proposed models in the presence of intermittently observed time-dependent covariates showed a good performance. However, when we considered only the observed values of the covariate without any imputations, the resulted biases were greater. The performances of the proposed SUR-based models in comparison with MRM using classic imputation methods were nearly similar with approximately equal amounts of bias and MSE. CONCLUSION. The simulation study suggests that the SUR-based models work as efficiently as MRM in the case of intermittently observed time-dependent covariates. Thus, it can be used as an alternative to MRM.

Experimental evaluation of the certification-trail method

NASA Technical Reports Server (NTRS)

Sullivan, Gregory F.; Wilson, Dwight S.; Masson, Gerald M.; Itoh, Mamoru; Smith, Warren W.; Kay, Jonathan S.

1993-01-01

Certification trails are a recently introduced and promising approach to fault-detection and fault-tolerance. A comprehensive attempt to assess experimentally the performance and overall value of the method is reported. The method is applied to algorithms for the following problems: huffman tree, shortest path, minimum spanning tree, sorting, and convex hull. Our results reveal many cases in which an approach using certification-trails allows for significantly faster overall program execution time than a basic time redundancy-approach. Algorithms for the answer-validation problem for abstract data types were also examined. This kind of problem provides a basis for applying the certification-trail method to wide classes of algorithms. Answer-validation solutions for two types of priority queues were implemented and analyzed. In both cases, the algorithm which performs answer-validation is substantially faster than the original algorithm for computing the answer. Next, a probabilistic model and analysis which enables comparison between the certification-trail method and the time-redundancy approach were presented. The analysis reveals some substantial and sometimes surprising advantages for ther certification-trail method. Finally, the work our group performed on the design and implementation of fault injection testbeds for experimental analysis of the certification trail technique is discussed. This work employs two distinct methodologies, software fault injection (modification of instruction, data, and stack segments of programs on a Sun Sparcstation ELC and on an IBM 386 PC) and hardware fault injection (control, address, and data lines of a Motorola MC68000-based target system pulsed at logical zero/one values). Our results indicate the viability of the certification trail technique. It is also believed that the tools developed provide a solid base for additional exploration.

Fast decoder for local quantum codes using Groebner basis

NASA Astrophysics Data System (ADS)

Haah, Jeongwan

2013-03-01

Based on arXiv:1204.1063. A local translation-invariant quantum code has a description in terms of Laurent polynomials. As an application of this observation, we present a fast decoding algorithm for translation-invariant local quantum codes in any spatial dimensions using the straightforward division algorithm for multivariate polynomials. The running time is O (n log n) on average, or O (n2 log n) on worst cases, where n is the number of physical qubits. The algorithm improves a subroutine of the renormalization-group decoder by Bravyi and Haah (arXiv:1112.3252) in the translation-invariant case. This work is supported in part by the Insitute for Quantum Information and Matter, an NSF Physics Frontier Center, and the Korea Foundation for Advanced Studies.

[Young French neurosurgeons: Working conditions and outlook].

PubMed

Pommier, B; Manet, R; Gay, E; Vassal, F; Nuti, C; Hladky, J-P

2015-10-01

Due to the increase in the number of French neurosurgeon residents the neurosurgical workforce is changing. The main objective of this survey was to assess working conditions and perspectives for young French neurosurgeons. An on-line survey was sent to young French neurosurgeons based on a mailing-list (219 mail addresses of Residents and Fellows obtained during previous meetings). The form contained questions about career, amount of work, salary, quality of life, teaching and university work. We received 78 replies from January to March 2014. A total of 56% from fellows saying they had undergone difficulties in obtaining a fellowship, although 78% were satisfied. Fellows considered a private career more often than residents. Overall, young neurosurgeons were worried about future employment. Some 33% admitted contemplating a different career from one they originally wanted. The average weekly working time of 76.8 hours was deemed to be excessive. Security rests after overnight shifts were lacking or incomplete in 91% of cases. The work atmosphere was good overall (3.7/5), and so was the quality of life (3.2/5). Theoretical teaching was unsatisfactory (2.43/5) as well as the time allowed for academic work (approximately 1.58 half-days per month). However, practical teaching was considered rewarding (3.63/5). This study provides some guidance for upcoming reforms, and should be considered again at a later date to evaluate progress. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Organising the Chemistry of Question-Based Learning: A Case Study

ERIC Educational Resources Information Center

de Jesus, Helena Pedrosa; de Souza, Francisle Neri; Teixeira-Dias, Jose J. C.; Watts, Mike

2005-01-01

Designing inquiry-based-learning with and for university students develops problem-solving skills and logical reasoning, as well as reflective thinking. It involves working as a member of a team, questioning, being creative, shaping the skills for continued intellectual development. It is argued that inquiry-based group work is one of the most…

Increased care demand and medical costs after falls in nursing homes: A Delphi study.

PubMed

Sterke, Carolyn Shanty; Panneman, Martien J; Erasmus, Vicki; Polinder, Suzanne; van Beeck, Ed F

2018-04-21

To estimate the increased care demand and medical costs caused by falls in nursing homes. There is compelling evidence that falls in nursing homes are preventable. However, proper implementation of evidence-based guidelines to prevent falls is often hindered by insufficient management support, staff time and funding. A three-round Delphi study. A panel of 41 experts, all working in nursing homes in the Netherlands, received three online questionnaires to estimate the extra hours of care needed during the first year after the fall. This was estimated for ten falls categories with different levels of injury severity, in three scenarios, that is a best-case, a typical-case and a worst-case scenario. We calculated the costs of falls by multiplying the mean amount of extra hours that the participants spent on the care for a resident after a fall with their hourly wages. In case of a noninjurious fall, the extra time spent on the faller is on average almost 5 hr, expressed in euros that add to € 193. The extra staff time and costs of falls increased with increasing severity of injury. In the case of a fracture of the lower limb, the extra staff time increased to 132 hr, expressed in euros that is € 4,604. In the worst-case scenario of a fracture of the lower limb, the extra staff time increased to 284 hr, expressed in euros that is € 10,170. Falls in nursing homes result in a great deal of extra staff time spent on care, with extra costs varying between € 193 for a noninjurious fall and € 10,170 for serious falls. This study could aid decision-making on investing in appropriate implementation of falls prevention interventions in nursing homes. © 2018 John Wiley & Sons Ltd.

Polynomial time blackbox identity testers for depth-3 circuits : the field doesn't matter.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seshadhri, Comandur; Saxena, Nitin

Let C be a depth-3 circuit with n variables, degree d and top fanin k (called {Sigma}{Pi}{Sigma}(k, d, n) circuits) over base field F. It is a major open problem to design a deterministic polynomial time blackbox algorithm that tests if C is identically zero. Klivans & Spielman (STOC 2001) observed that the problem is open even when k is a constant. This case has been subjected to a serious study over the past few years, starting from the work of Dvir & Shpilka (STOC 2005). We give the first polynomial time blackbox algorithm for this problem. Our algorithm runsmore » in time poly(n)d{sup k}, regardless of the base field. The only field for which polynomial time algorithms were previously known is F = Q (Kayal & Saraf, FOCS 2009, and Saxena & Seshadhri, FOCS 2010). This is the first blackbox algorithm for depth-3 circuits that does not use the rank based approaches of Karnin & Shpilka (CCC 2008). We prove an important tool for the study of depth-3 identities. We design a blackbox polynomial time transformation that reduces the number of variables in a {Sigma}{Pi}{Sigma}(k, d, n) circuit to k variables, but preserves the identity structure. Polynomial identity testing (PIT) is a major open problem in theoretical computer science. The input is an arithmetic circuit that computes a polynomial p(x{sub 1}, x{sub 2},..., x{sub n}) over a base field F. We wish to check if p is the zero polynomial, or in other words, is identically zero. We may be provided with an explicit circuit, or may only have blackbox access. In the latter case, we can only evaluate the polynomial p at various domain points. The main goal is to devise a deterministic blackbox polynomial time algorithm for PIT.« less

Women in rural development.

PubMed

Palmer, I

1980-01-01

The integration of women in rural development means something more than mere labor involvement, but there has never been a clear definition of what it means. 4 principal concerns of policy-makers are briefly described as they affect women: unemployment and inadequate employment; 2) the satisfaction of basic needs and women's participation in decision-making; 3) population issues; and 4) rural-to-urban migration. The actual inter-household and inter-personal distribution of more work and higher productivity work could result in some hard-working people working even longer hours because of additional tasks with others losing their intermittent employment opportunities due to mechanization. These contradictions can be particularly acute for women. The non-material basic need of decision-making powers is more important in the case of women than of men, yet the personal status of women is being threatened by the institution-building that accompanies peasant-based agricultural intensification plans and anti-poverty programs. The education of females has been seen as a possible factor favoring family planning. In addition, education for women can mean access to public information and new expectations from life for themselves. At this time more women than men seem to be migrating to towns and cities in a number of countries with varied economic structures. 3 cases studies of agricultural development in Kenya, Bangladesh and Java, Indonesia are presented.

Spontaneous abortion in the British semiconductor industry: An HSE investigation. Health and Safety Executive.

PubMed

Elliott, R C; Jones, J R; McElvenny, D M; Pennington, M J; Northage, C; Clegg, T A; Clarke, S D; Hodgson, J T; Osman, J

1999-11-01

The UK Health and Safety Executive (HSE) conducted a study to examine the risk of spontaneous abortion (SAB) in British female semiconductor industry workers, following reports from the USA which suggested an association between risk of SAB and work in fabrication rooms and/or exposure to ethylene glycol ethers. A nested case-control study based on 2,207 women who had worked at eight manufacturing sites during a 5-year retrospective time frame was established; 36 cases were matched with 80 controls. The overall SAB rate in the industry was 10.0%. (65 SABs/651 pregnancies) The crude odds ratio (OR) for fabrication work was 0.65 (95% CI 0.30-1.40). This was essentially unchanged after adjustment for a range of potential confounding factors in the first 3 months of pregnancy and was reduced to 0.58 (95% CI 0.26-1.30) after adjustment for smoking in the previous 12 months. There were no statistically significantly elevated ORs for any work group or any specific chemical or physical exposure in the industry. There is no evidence of an increased risk of SAB in the British semiconductor industry. Am. J. Ind. Med. 36:557-572, 1999. Published 1999 Wiley-Liss, Inc.

The work of commissioning: a multisite case study of healthcare commissioning in England's NHS

PubMed Central

Shaw, Sara E; Smith, Judith A; Porter, Alison; Rosen, Rebecca; Mays, Nicholas

2013-01-01

Objective To examine the work of commissioning care for people with long-term conditions and the factors inhibiting or facilitating commissioners making service change. Design Multisite mixed methods case study research, combining qualitative analysis of interviews, documents and observation of meetings. Participants Primary care trust managers and clinicians, general practice-based commissioners, National Health Service trust and foundation trust senior managers and clinicians, voluntary sector and local government representatives. Setting Three ‘commissioning communities’ (areas covered by a primary care trust) in England, 2010–2012. Results Commissioning services for people with long-term conditions was a long drawn-out process involving a range of activities and partners. Only some of the activities undertaken by commissioners, such as assessment of local health needs, coordination of healthcare planning and service specification, appeared in the official ‘commissioning cycle’ promoted by the Department of Health. Commissioners undertook a significant range of additional activities focused on reviewing and redesigning services and providing support for implementation of new services. These activities often involved partnership working with providers and other stakeholders and appeared to be largely divorced from contracting and financial negotiations. At least for long-term condition services, the time and effort involved in such work appeared to be disproportionate to the anticipated or likely service gains. Commissioners adopting an incremental approach to service change in defined and manageable areas of work appeared to be more successful in terms of delivering planned changes in service delivery than those attempting to bring about wide-scale change across complex systems. Conclusions Commissioning for long-term condition services challenges the conventional distinction between commissioners and providers with a significant amount of work focused on redesigning services in partnership with providers. Such work is labour-intensive and potentially unsustainable at a time of reduced finances. New clinical commissioning groups will need to determine how best to balance the relational and transactional elements of commissioning. PMID:24014483

Stories of Self and Science: Preservice Elementary Teachers' Identity Work through Time and across Contexts

ERIC Educational Resources Information Center

Avraamidou, Lucy

2016-01-01

Grounded in theoretical and empirical underpinnings related to identity work and figured worlds, this case study explores the nature of two preservice elementary teachers' identities for science teaching and the experiences that impacted their development through time and across contexts. The participants in this study portray a range of…

"Learning to Play with New Friends": Systematic Quality Development Work in a Leisure-Time Centre

ERIC Educational Resources Information Center

Lager, Karin

2016-01-01

This article explores the recontextualisation of systematic quality development work (Sqdw) in a leisure-time centre. Two teachers' processes of planning, organisation, documentation and evaluation were investigated, the aim being to explore the recontextualisation of Sqdw in practice. The study is thus a case study of these teachers' practice…

Case-based synthesis in automatic advertising creation system

NASA Astrophysics Data System (ADS)

Zhuang, Yueting; Pan, Yunhe

1995-08-01

Advertising (ads) is an important design area. Though many interactive ad-design softwares have come into commercial use, none of them ever support the intelligent work -- automatic ad creation. The potential for this is enormous. This paper gives a description of our current work in research of an automatic advertising creation system (AACS). After careful analysis of the mental behavior of a human ad designer, we conclude that case-based approach is appropriate to its intelligent modeling. A model for AACS is given in the paper. A case in ads is described as two parts: the creation process and the configuration of the ads picture, with detailed data structures given in the paper. Along with the case representation, we put forward an algorithm. Some issues such as similarity measure computing, and case adaptation have also been discussed.

The careers of women graduates from St Mary's Hospital Medical School, London, 1961--72.

PubMed

Shaw, H E

1979-07-01

The careers of women doctors who qualified from St Mary's Hospital Medical School between 1961 and 1972 inclusive have been studied. Thirty-eight per cent were in full-time work, 47% were working part-time, and 15% were not practising medicine at the time of the survey. Those working full-time were predominantly single women and married women with no children. With the birth of children most women stopped working for a time, and 38% of those whose children were all under school age were not working. However, 90% returned to medicine, usually to part-time jobs that were compatible with family responsibilities. Eighty-six per cent of the respondents held one or more postgraduate qualifications. More of those with higher qualifications were in full-time work than was the case for women with a basic medical degree only, and fewer were not practising medicine. An equal proportion of single and married women intended to make their career in general practice. Fewer married women than single women chose a hospital career, because the possibilities of part-time work in this field were seen as limited.

GPU-based ultra-fast dose calculation using a finite size pencil beam model.

PubMed

Gu, Xuejun; Choi, Dongju; Men, Chunhua; Pan, Hubert; Majumdar, Amitava; Jiang, Steve B

2009-10-21

Online adaptive radiation therapy (ART) is an attractive concept that promises the ability to deliver an optimal treatment in response to the inter-fraction variability in patient anatomy. However, it has yet to be realized due to technical limitations. Fast dose deposit coefficient calculation is a critical component of the online planning process that is required for plan optimization of intensity-modulated radiation therapy (IMRT). Computer graphics processing units (GPUs) are well suited to provide the requisite fast performance for the data-parallel nature of dose calculation. In this work, we develop a dose calculation engine based on a finite-size pencil beam (FSPB) algorithm and a GPU parallel computing framework. The developed framework can accommodate any FSPB model. We test our implementation in the case of a water phantom and the case of a prostate cancer patient with varying beamlet and voxel sizes. All testing scenarios achieved speedup ranging from 200 to 400 times when using a NVIDIA Tesla C1060 card in comparison with a 2.27 GHz Intel Xeon CPU. The computational time for calculating dose deposition coefficients for a nine-field prostate IMRT plan with this new framework is less than 1 s. This indicates that the GPU-based FSPB algorithm is well suited for online re-planning for adaptive radiotherapy.

Safety in out-of-hours operating in trauma and orthopaedics at a district general hospital.

PubMed

Gulamhussein, M A; Chaudhry, S; Noor, S; Chaudhry, T; Guha, A; Knebel, R

2017-05-01

INTRODUCTION According to the National Confidential Enquiry into Perioperative Deaths (NCEPOD), out-of-hours operating in trauma and orthopaedics should be reserved for life or limb threatening cases only. The aim of our study was to determine the nature of non-emergency work carried out in our trust at night in 2015. The overall efficacy and clinical safety of the services provided was evaluated. METHODS Surgical activity undertaken after 9pm was reviewed along with patient ASA (American Society of Anesthesiologists) grade, grade of operating surgeon and any complications that occurred following the procedure. Furthermore, the clinical urgency and safety of cases was assessed based on whether there was any record of life or limb threatening indications at the time of admission. RESULTS Overall, 131 procedures were performed after 9pm, with 102 performed between 9pm and midnight, and 29 after midnight. Consultants performed 16 cases and the remaining 115 cases were operated on by middle grades or specialty trainees. A fifth (20%) of the cases were genuinely life or limb threatening. A total of 123 procedures were classed as having good outcomes. The complication rate was 8%. CONCLUSIONS In our study, 80% of the procedures performed after 9pm could not be categorised as life or limb threatening. Appropriate NCEPOD classification would ensure that only life or limb threatening cases were listed for theatre after 9pm. Alternative methods of operating within working hours should be considered.

Safety in out-of-hours operating in trauma and orthopaedics at a district general hospital

PubMed Central

Chaudhry, S; Noor, S; Chaudhry, T; Guha, A; Knebel, R

2017-01-01

INTRODUCTION According to the National Confidential Enquiry into Perioperative Deaths (NCEPOD), out-of-hours operating in trauma and orthopaedics should be reserved for life or limb threatening cases only. The aim of our study was to determine the nature of non-emergency work carried out in our trust at night in 2015. The overall efficacy and clinical safety of the services provided was evaluated. METHODS Surgical activity undertaken after 9pm was reviewed along with patient ASA (American Society of Anesthesiologists) grade, grade of operating surgeon and any complications that occurred following the procedure. Furthermore, the clinical urgency and safety of cases was assessed based on whether there was any record of life or limb threatening indications at the time of admission. RESULTS Overall, 131 procedures were performed after 9pm, with 102 performed between 9pm and midnight, and 29 after midnight. Consultants performed 16 cases and the remaining 115 cases were operated on by middle grades or specialty trainees. A fifth (20%) of the cases were genuinely life or limb threatening. A total of 123 procedures were classed as having good outcomes. The complication rate was 8%. CONCLUSIONS In our study, 80% of the procedures performed after 9pm could not be categorised as life or limb threatening. Appropriate CEPOD classification would ensure that only life or limb threatening cases were listed for theatre after 9pm. Alternative methods of operating within working hours should be considered. PMID:27917666

Occupational lung diseases in Australia.

PubMed

Hoy, Ryan F; Brims, Fraser

2017-11-20

Occupational exposures are an important determinant of respiratory health. International estimates note that about 15% of adult-onset asthma, 15% of chronic obstructive pulmonary disease and 10-30% of lung cancer may be attributable to hazardous occupational exposures. One-quarter of working asthmatics either have had their asthma caused by work or adversely affected by workplace conditions. Recently, cases of historical occupational lung diseases have been noted to occur with new exposures, such as cases of silicosis in workers fabricating kitchen benchtops from artificial stone products. Identification of an occupational cause of a lung disease can be difficult and requires maintaining a high index of suspicion. When an occupational lung disease is identified, this may facilitate a cure and help to protect coworkers. Currently, very little information is collected regarding actual cases of occupational lung diseases in Australia. Most assumptions about many occupational lung diseases are based on extrapolation from overseas data. This lack of information is a major impediment to development of targeted interventions and timely identification of new hazardous exposures. All employers, governments and health care providers in Australia have a responsibility to ensure that the highest possible standards are in place to protect workers' respiratory health.

Web-Based Environment for Maintaining Legacy Software

NASA Technical Reports Server (NTRS)

Tigges, Michael; Thompson, Nelson; Orr, Mark; Fox, Richard

2007-01-01

Advanced Tool Integration Environment (ATIE) is the name of both a software system and a Web-based environment created by the system for maintaining an archive of legacy software and expertise involved in developing the legacy software. ATIE can also be used in modifying legacy software and developing new software. The information that can be encapsulated in ATIE includes experts documentation, input and output data of tests cases, source code, and compilation scripts. All of this information is available within a common environment and retained in a database for ease of access and recovery by use of powerful search engines. ATIE also accommodates the embedment of supporting software that users require for their work, and even enables access to supporting commercial-off-the-shelf (COTS) software within the flow of the experts work. The flow of work can be captured by saving the sequence of computer programs that the expert uses. A user gains access to ATIE via a Web browser. A modern Web-based graphical user interface promotes efficiency in the retrieval, execution, and modification of legacy code. Thus, ATIE saves time and money in the support of new and pre-existing programs.

The Case For Prediction-based Best-effort Real-time Systems.

DTIC Science & Technology

1999-01-01

Real - time Systems Peter A. Dinda Loukas Kallivokas January...DISTRIBUTION STATEMENT A Approved for Public Release Distribution Unlimited DTIG QUALBR DISSECTED X The Case For Prediction-based Best-effort Real - time Systems Peter...Mellon University Pittsburgh, PA 15213 A version of this paper appeared in the Seventh Workshop on Parallel and Distributed Real - Time Systems

Amounts and activity concentrations of radioactive wastes from the cleanup of large areas contaminated in nuclear accidents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lehto, J.; Ikaeheimonen, T.K.; Salbu, B.

The fallout from a major nuclear accident at a nuclear plant may result in a wide-scale contamination of the environment. Cleanup of contaminated areas is of special importance if these areas are populated or cultivated. All cleanup measures generate high amounts of radioactive waste, which have to be treated and disposed of in a safe manner. Scenarios assessing the amounts and activity concentrations of radioactive wastes for various cleanup measures after severe nuclear accidents have been worked out for urban, forest and agricultural areas. These scenarios are based on contamination levels and ares of contaminated lands from a model accident,more » which simulates a worst case accident at a nuclear power plant. Amounts and activity concentrations of cleanup wastes are not only dependent on the contamination levels and areas of affected lands, but also on the type of deposition, wet or dry, on the time between the deposition and the cleanup work, on the season, at which the deposition took place, and finally on the level of cleanup work. In this study practically all types of cleanup wastes were considered, whether or not the corresponding cleanup measures are cost-effective or justified. All cleanup measures are shown to create large amounts of radioactive wastes, but the amounts, as well as the activity concentrations vary widely from case to case.« less

Evaluation of ConPrim: A three-part model for continuing education in primary health care.

PubMed

Berggren, Erika; Strang, Peter; Orrevall, Ylva; Ödlund Olin, Ann; Sandelowsky, Hanna; Törnkvist, Lena

2016-11-01

To overcome the gap between existing knowledge and the application of this knowledge in practice, a three-part continuing educational model for primary health care professionals (ConPrim) was developed. It includes a web-based program, a practical exercise and a case seminar. To evaluate professionals' perceptions of the design, pedagogy and adaptation to primary health care of the ConPrim continuing educational model as applied in a subject-specific intervention. A total of 67 professionals (nurses and physicians) completed a computer-based questionnaire evaluating the model's design, pedagogy and adaptation to primary health care one week after the intervention. Descriptive statistics were used. Over 90% found the design of the web-based program and case seminar attractive; 86% found the design of the practical exercise attractive. The professionals agreed that the time spent on two of the three parts was acceptable. The exception was the practical exercise: 32% did not fully agree. Approximately 90% agreed that the contents of all parts were relevant to their work and promoted interactive and interprofessional learning. In response to the statements about the intervention as whole, approximately 90% agreed that the intervention was suitable to primary health care, that it had increased their competence in the subject area, and that they would be able to use what they had learned in their work. ConPrim is a promising model for continuing educational interventions in primary health care. However, the time spent on the practical exercise should be adjusted and the instructions for the exercise clarified. ConPrim should be tested in other subject-specific interventions and its influence on clinical practice should be evaluated. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Pneumoconiosis in different sectors and their differences in Turkey.

PubMed

Alıcı, Nur Şafak; Çımrın, Arif; Coşkun Beyan, Ayşe

2016-12-01

Pneumoconiosis which is one of the ancient diseases, still affects many workers throughout the world despite "existing" control programs. We add data from a single center reviewing risk factors for pneumoconiosis; evaluate functional and radiological findings in different sectors. We reviewed medical records of patients diagnosed with pneumoconiosis who were admitted to our center between the years 2013 and 2015. Several personal and occupational features, together with functional and radiologic data, were collected. 60 were young males. Twenty-four of the cases (39.3%) worked at dental technician, 24 cases (39.3%) were ceramic workers, 5 cases (8.2%) were sandblasters, 2 cases (3.3%) were welders, 3 cases (4.9%) were miners, and 3 cases (4.9%) were marble cutters. The sectors in which the exposure started at the earliest ages were dental technicians and sandblasters, while the shortest working time was in sandblasting. The dental technicians were younger than the ceramic workers at the age of diagnosis (Kruskall-Wallis p= 0.003). The exposure time of the sandblasters was significantly shorter, especially than the ceramic workers (Kruskall-Wallis p= 0.002). The cases have been referred to us with pneumoconiosis suspicion based on the radiographic findings in the PA chest roentgenogram performed during the periodic examinations at their work place; but unlike other studies, in our study, following the HRCT assessment, cases which did not present any visible pathology in the re-evaluation of their PA chest roentgenogram, but had HRCT findings have been diagnosed as pneumoconiosis. Among the 44 cases in which micro-nodules had been detected at their HRCT, 15 of them had been previously classified as profusion of small opacities 0/1 according to their PA chest roentgenogram findings. It has been seen that the HRCT findings differ among sectors. Ceramics workers and sandblasters had significantly more micro-nodules, while dental technicians had significantly more mediastinal lymphadenopathies (Chi square, p= 0.004 and p= 0.007 respectively). When the relationship between the existence of big opacities and complaints was studied, statistically significant weight loss was detected in cases which had C opacities (chi square p= 0.01). Statistically significant FEV1 decrease was observed in cases which had weight loss (independent samples t-test p= 0.046). It has been observed that when the profusion of small opacities increased, while there was no statistically significant functional status change in non-smokers, a significant functional impairment was observed in smokers. Pneumoconiosis still exists in Turkey. Even a short exposure time as 2 years can cause pneumoconiosis. Workers in different sectors had different functional, radiological properties and smoking can affect the diseases' course. There are serious limitations related to the surveillance of both the workplace environment and the employees' health in Turkey. Without institutional preventive measures, personal protection and surveillance examinations, occupational hazards will continue to cause premature deaths. Pneumoconiosis in different sectors is a prototype of uncontrolled industry in the developing world.

The quality dilemma.

PubMed

Lucassen, Peter

2007-06-01

In the language and logic of the free market, providers of health care will have to demonstrate the quality of their work. However, in this setting quality is only interpreted in quantitative ways and consequently does not necessarily do justice to good physicians. Moreover, both outcome measures and process measures have serious drawbacks. An emphasis on outcome measures will disadvantage physicians working in deprived areas and doctors managing more complicated cases. Although process measures give the most direct information on the physician's performance, their evidence base is not always as straightforward as commonly supposed. Finally, measurement of quality indicators is complicated and time consuming. Physicians should be aware of the drawbacks of quality measurement and of the poor effects of quality improvement strategies on patient outcomes.

A multibiometric face recognition fusion framework with template protection

NASA Astrophysics Data System (ADS)

Chindaro, S.; Deravi, F.; Zhou, Z.; Ng, M. W. R.; Castro Neves, M.; Zhou, X.; Kelkboom, E.

2010-04-01

In this work we present a multibiometric face recognition framework based on combining information from 2D with 3D facial features. The 3D biometrics channel is protected by a privacy enhancing technology, which uses error correcting codes and cryptographic primitives to safeguard the privacy of the users of the biometric system at the same time enabling accurate matching through fusion with 2D. Experiments are conducted to compare the matching performance of such multibiometric systems with the individual biometric channels working alone and with unprotected multibiometric systems. The results show that the proposed hybrid system incorporating template protection, match and in some cases exceed the performance of corresponding unprotected equivalents, in addition to offering the additional privacy protection.

New well testing applications of the pressure derivative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onur, M.

1989-01-01

This work presents new derivative type curves based on a new derivative group which is equal to the dimensionless pressure group divided by its logarithmic derivative with respect to dimensionless time group. One major advantage of these type curves is that the type-curve match of field pressure/pressure-derivative data with the new derivative type curves is accomplished by moving the field data plot in only the horizontal direction. This type-curve match fixes time match-point values. The pressure change versus time data is then matched with the dimensionless pressure solution to determine match-point values. Well/reservoir parameters can then be estimated in themore » standard way. This two step type-curve matching procedure increases the likelihood of obtaining a unique match. Moreover, the unique correspondence between the ordinate of the field data plot and the new derivative type curves should prove useful in determining whether given field data actually represents the well/reservoir model assumed by a selected type curve solution. It is also shown that the basic idea used in construction the type curves can be used to ensure that proper semilog straight lines are chosen when analyzing pressure data by semilog methods. Analysis of both drawdown and buildup data is considered and actual field cases are analyzed using the new derivative type curves and the semilog identification method. This work also presents new methods based on the pressure derivative to analyze buildup data obtained at a well (fracture or unfractured) produced to pseudosteady-state prior to shut-in. By using a method of analysis based on the pressure derivative, it is shown that a well's drainage area at the instant of shut-in and the flow capacity can be computed directly from buildup data even in cases where conventional semilog straight lines are not well-defined.« less

Time management for case managers--so much work, so little time.

PubMed

Cesta, Toni

2014-08-01

The world of a case manager is a busy one, and you may not have all the resources you need each and every day. If you can maintain a routine it will make the workload more manageable for you and will allow room for those surprises that invariably happen. Whether you are a new or a seasoned case manager, organizing your workload can always help smooth out the rough edges in anyone's hectic day!

Lyapounov Functions of Closed Cone Fields: From Conley Theory to Time Functions

NASA Astrophysics Data System (ADS)

Bernard, Patrick; Suhr, Stefan

2018-03-01

We propose a theory "à la Conley" for cone fields using a notion of relaxed orbits based on cone enlargements, in the spirit of space time geometry. We work in the setting of closed (or equivalently semi-continuous) cone fields with singularities. This setting contains (for questions which are parametrization independent such as the existence of Lyapounov functions) the case of continuous vector-fields on manifolds, of differential inclusions, of Lorentzian metrics, and of continuous cone fields. We generalize to this setting the equivalence between stable causality and the existence of temporal functions. We also generalize the equivalence between global hyperbolicity and the existence of a steep temporal function.

Quantum control of isomerization by robust navigation in the energy spectrum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murgida, G. E., E-mail: murgida@tandar.cnea.gov.ar; Arranz, F. J., E-mail: fj.arranz@upm.es; Borondo, F., E-mail: f.borondo@uam.es

2015-12-07

In this paper, we present a detailed study on the application of the quantum control technique of navigation in the energy spectrum to chemical isomerization processes, namely, CN–Li⇆ Li–CN. This technique is based on the controlled time variation of a Hamiltonian parameter, an external uniform electric field in our case. The main result of our work establishes that the navigation involved in the method is robust, in the sense that quite sizable deviations from a pre-established control parameter time profile can be introduced and still get good final results. This is specially relevant thinking of a experimental implementation of themore » method.« less

Diagnostic Efficiency in Digital Pathology: A Comparison of Optical Versus Digital Assessment in 510 Surgical Pathology Cases.

PubMed

Mills, Anne M; Gradecki, Sarah E; Horton, Bethany J; Blackwell, Rebecca; Moskaluk, Christopher A; Mandell, James W; Mills, Stacey E; Cathro, Helen P

2018-01-01

Prior work has shown that digital images and microscopic slides can be interpreted with comparable diagnostic accuracy. Although accuracy has been well-validated, the interpretative time for digital images has scarcely been studied and concerns about efficiency remain a major barrier to adoption. We investigated the efficiency of digital pathology when compared with glass slide interpretation in the diagnosis of surgical pathology biopsy and resection specimens. Slides were pulled from 510 surgical pathology cases from 5 organ systems (gastrointestinal, gynecologic, liver, bladder, and brain). Original diagnoses were independently confirmed by 2 validating pathologists. Diagnostic slides were scanned using the Philips IntelliSite Pathology Solution. Each case was assessed independently on digital and optical by 3 reading pathologists, with a ≥6 week washout period between modalities. Reading pathologists recorded assessment times for each modality; digital times included time to load the case. Diagnostic accuracy was determined based on whether a rendered diagnosis differed significantly from the original diagnosis. Statistical analysis was performed to assess for differences in interpretative times across modalities. All 3 reading pathologists showed comparable diagnostic accuracy across optical and digital modalities (mean major discordance rates with original diagnosis: 4.8% vs. 4.4%, respectively). Mean assessment times ranged from 1.2 to 9.1 seconds slower on digital versus optical. The slowest reader showed a significant learning effect during the course of the study so that digital assessment times decreased over time and were comparable with optical times by the end of the series. Organ site and specimen type did not significantly influence differences in interpretative times. In summary, digital image reading times compare favorably relative to glass slides across a variety of organ systems and specimen types. Mean increase in assessment time is 4 seconds/case. This time can be minimized with experience and may be further balanced by the improved ease of electronic chart access allowed by digital slide viewing, as well as quantitative assessments which can be expedited on digital images.

Attributable fraction of work accidents related to occupational noise exposure in a Southeastern city of Brazil.

PubMed

Dias, Adriano; Cordeiro, Ricardo

2007-07-01

Noise is the most frequent type of occupational exposure and can lead to both auditory and extra-auditory dysfunction as well as increasing the risk of work accidents. The purpose of this study was to estimate the attributable fraction of work accidents related to occupational noise exposure in a medium-sized city in Southeast Brazil. In this hospital-based case-control study, including 600 cases and 822 controls, the odds ratio of work accidents (controlled for several covariables) was obtained classifying occupational noise exposure into four levels and determining the prevalence at each level. Based on these data, the calculated attributable fraction was 0.3041 (95%CI: 0.2341-0.3676), i.e., 30% of work accidents in the study area were statistically associated with occupational noise exposure. The authors discuss the causes of this association and the implications for the prevention of work accidents.

Work-family conflict and sleep disturbance: the Malaysian working women study

PubMed Central

AAZAMI, Sanaz; MOZAFARI, Mosayeb; SHAMSUDDIN, Khadijah; AKMAL, Syaqirah

2015-01-01

This study aimed at assessing effect of the four dimensions of work-family conflicts (strain and time-based work interference into family and family interference into work) on sleep disturbance in Malaysian working women. This cross-sectional study was conducted among 325 Malaysian married working women. Multiple-stage simple random sampling method was used to recruit women from public service departments of Malaysia. Self-administrated questionnaires were used to measure the study variables and data were analyzed using SPSS version 21. We found that high level of the four dimensions of work-family conflicts significantly increase sleep disturbance. Our analyses also revealed an age-dependent effect of the work-family conflict on sleep disturbance. Women in their 20 to 30 yr old suffer from sleep disturbance due to high level of time-based and strain-based work-interference into family. However, the quality of sleep among women aged 30–39 were affected by strain-based family-interference into work. Finally, women older than 40 yr had significantly disturbed sleep due to strain-based work-interference into family as well as time-based family interference into work. Our findings showed that sleep quality of working women might be disturbed by experiencing high level of work-family conflict. However, the effects of inter-role conflicts on sleep varied among different age groups. PMID:26423332

Social work in health care: do practitioners' writings suggest an applied social science?

PubMed

Rehr, H; Rosenberg, G; Showers, N; Blumenfield, S

1998-01-01

There are two sources of literature in social work-one from academics and the other from practitioners. Each group is driven by different motivations to write. Academics seek a 'scientific rationality' for the field, while practitioners assume practical and intuitive reasoning, experience aligned with theory, and the 'art of practice' to guide them. It has been said that practitioners do not write and that 'faculty' are the trustees of the knowledge base of the profession, and are responsible for its promulgation via publication. Practitioners, however, do write about their practice and their programs, and analyze both, but publish much of their work in non-social work media. Their work tends not to be referenced by academic writers. One department's social workers' publications are described. We learn, from their practice writings, what concerns clinicians. Theirs is case-based learning, theoretically supported, in which the organization of services calls for their participation in multi-professional decision-making. There is the growing realization among social workers that practice wisdom and scientific technologies need to be reassessed together to find ways to enhance social work services. Clinicians' knowledge can lead to continuing refinement of practice and enhanced institutional services. If practitioners' writings can be assessed, they may lead to a written practice knowledge base, subject to timely change. Academic and practitioner separateness hampers progress in the field. They need each other, and a shared professional literature. There is beginning indication they are getting together.

The Place of Community-Based Learning in Higher Education: A Case Study of Interchange

ERIC Educational Resources Information Center

Hardwick, Louise

2013-01-01

This article focuses on one strand of community engagement: community-based learning for students. It considers in particular Interchange as a case study. Interchange is a registered charity based in, but independent of, a department in a Higher Education Institution. It brokers between undergraduate research/work projects and Voluntary Community…

The Development of Work-Based Learning as Part of Post-Qualifying Education: A Case Study from the School of Nursing, University of Salford, UK

ERIC Educational Resources Information Center

Owens, Denise; Rutherford, June

2007-01-01

This paper describes the conception and progress to date of the development of work-based learning as part of post-qualifying education in the School of Nursing at the University of Salford. There is a changing culture in the university in relation to the delivery of programmes via non-traditional routes. In this context, work-based learning is a…

Towards real-time photon Monte Carlo dose calculation in the cloud

NASA Astrophysics Data System (ADS)

Ziegenhein, Peter; Kozin, Igor N.; Kamerling, Cornelis Ph; Oelfke, Uwe

2017-06-01

Near real-time application of Monte Carlo (MC) dose calculation in clinic and research is hindered by the long computational runtimes of established software. Currently, fast MC software solutions are available utilising accelerators such as graphical processing units (GPUs) or clusters based on central processing units (CPUs). Both platforms are expensive in terms of purchase costs and maintenance and, in case of the GPU, provide only limited scalability. In this work we propose a cloud-based MC solution, which offers high scalability of accurate photon dose calculations. The MC simulations run on a private virtual supercomputer that is formed in the cloud. Computational resources can be provisioned dynamically at low cost without upfront investment in expensive hardware. A client-server software solution has been developed which controls the simulations and transports data to and from the cloud efficiently and securely. The client application integrates seamlessly into a treatment planning system. It runs the MC simulation workflow automatically and securely exchanges simulation data with the server side application that controls the virtual supercomputer. Advanced encryption standards were used to add an additional security layer, which encrypts and decrypts patient data on-the-fly at the processor register level. We could show that our cloud-based MC framework enables near real-time dose computation. It delivers excellent linear scaling for high-resolution datasets with absolute runtimes of 1.1 seconds to 10.9 seconds for simulating a clinical prostate and liver case up to 1% statistical uncertainty. The computation runtimes include the transportation of data to and from the cloud as well as process scheduling and synchronisation overhead. Cloud-based MC simulations offer a fast, affordable and easily accessible alternative for near real-time accurate dose calculations to currently used GPU or cluster solutions.

Towards real-time photon Monte Carlo dose calculation in the cloud.

PubMed

Ziegenhein, Peter; Kozin, Igor N; Kamerling, Cornelis Ph; Oelfke, Uwe

2017-06-07

Near real-time application of Monte Carlo (MC) dose calculation in clinic and research is hindered by the long computational runtimes of established software. Currently, fast MC software solutions are available utilising accelerators such as graphical processing units (GPUs) or clusters based on central processing units (CPUs). Both platforms are expensive in terms of purchase costs and maintenance and, in case of the GPU, provide only limited scalability. In this work we propose a cloud-based MC solution, which offers high scalability of accurate photon dose calculations. The MC simulations run on a private virtual supercomputer that is formed in the cloud. Computational resources can be provisioned dynamically at low cost without upfront investment in expensive hardware. A client-server software solution has been developed which controls the simulations and transports data to and from the cloud efficiently and securely. The client application integrates seamlessly into a treatment planning system. It runs the MC simulation workflow automatically and securely exchanges simulation data with the server side application that controls the virtual supercomputer. Advanced encryption standards were used to add an additional security layer, which encrypts and decrypts patient data on-the-fly at the processor register level. We could show that our cloud-based MC framework enables near real-time dose computation. It delivers excellent linear scaling for high-resolution datasets with absolute runtimes of 1.1 seconds to 10.9 seconds for simulating a clinical prostate and liver case up to 1% statistical uncertainty. The computation runtimes include the transportation of data to and from the cloud as well as process scheduling and synchronisation overhead. Cloud-based MC simulations offer a fast, affordable and easily accessible alternative for near real-time accurate dose calculations to currently used GPU or cluster solutions.

Case Report on the Use of the Waldon Approach on an Adult with Severe to Moderate Intellectual Disability with Autistic Tendencies.

PubMed

Solomon, Walter G; Greenbaum, Eran

2016-01-01

This clinical case report describes a patient diagnosed with severe to moderate intellectual disability with autistic tendencies, resident in a home for adults with a range of disabilities. She had been resident for 18 years prior to intervention by the author when she was 48 years of age. The author worked with her from June 25, 2013 until January 12, 2015 for a total of 55 Waldon Approach (1), movement-based lessons each of about 45 min of which 33 were documented by video. This report describes changes in her cognition and her social behavior at a time when there were no other changes in her life. As far as the author is aware, this is the first clinical case report on the Waldon Approach to appear in a peer-reviewed journal and is unique in that most of the work using the approach is with children who are usually receiving other therapies at the same time as their Waldon Lessons, making it harder to evaluate the attribution of change. During the period of this report, she received no other therapy or intervention beyond that provided at Maon Roglit, which itself had not changed during this period. The patient remains without speech, but there has been real, meaningful, and noticeable change in her life from which she appears to derive pleasure. There has been a significant improvement in the patient's group participation, facial expression, and general demeanor.

Aeroacoustic simulation of a linear cascade by a prefactored compact scheme

NASA Astrophysics Data System (ADS)

Ghillani, Pietro

This work documents the development of a three-dimensional high-order prefactored compact finite-difference solver for computational aeroacoustics (CAA) based on the inviscid Euler equations. This time explicit scheme is applied to representative problems of sound generation by flow interacting with solid boundaries. Four aeroacoustic problems are explored and the results validated against available reference analytical solution. Selected mesh convergence studies are conducted to determine the effective order of accuracy of the complete scheme. The first test case simulates the noise emitted by a still cylinder in an oscillating field. It provides a simple validation for the CAA-compatible solid wall condition used in the remainder of the work. The following test cases are increasingly complex versions of the turbomachinery rotor-stator interaction problem taken from NASA CAA workshops. In all the cases the results are compared against the available literature. The numerical method features some appreciable contributions to computational aeroacoustics. A reduced data exchange technique for parallel computations is implemented, which requires the exchange of just two values for each boundary node, independently of the size of the zone overlap. A modified version of the non-reflecting buffer layer by Chen is used to allow aerodynamic perturbations at the through flow boundaries. The Giles subsonic boundary conditions are extended to three-dimensional curvilinear coordinates. These advances have enabled to resolve the aerodynamic noise generation and near-field propagation on a representative cascade geometry with a time-marching scheme, with accuracy similar to spectral methods..

The Use of Decision Cases to Foster Critical Thinking in Social Work Students

ERIC Educational Resources Information Center

Milner, Marleen; Wolfer, Terry

2014-01-01

This article discusses the vital importance of developing critical thinking skills in social work students and explores the use of case-based instruction as a means of fostering those skills. The challenges inherent in the teaching and assessment of critical thinking are addressed. The history and theoretical underpinnings for the use of decision…

Theoretical Modeling of the Interior Ballistics of the Electrothermal Gun

DTIC Science & Technology

1993-07-01

latter one 19 Table 2.1 Parameters Used for Nominal Data Base (after Oberle [2]). Chamber Volume 97.108 cm 3 Projectile Travel 145 cm Bore Diameter 14...at the time when the plasma supply is completed. When this occurs in the case of instantaneous mixing one has the projectile travel reduced by... Travel 400.0 cm Bore Diameter 4.0 cm Projectile Hass 160 g Plasma Energy 2000000 J Plasma Mass 0.0 g Working Fluid 420 g of H20 Density I g/cm. Bulk

Quantum Support Vector Machine for Big Data Classification

NASA Astrophysics Data System (ADS)

Rebentrost, Patrick; Mohseni, Masoud; Lloyd, Seth

2014-09-01

Supervised machine learning is the classification of new data based on already classified training examples. In this work, we show that the support vector machine, an optimized binary classifier, can be implemented on a quantum computer, with complexity logarithmic in the size of the vectors and the number of training examples. In cases where classical sampling algorithms require polynomial time, an exponential speedup is obtained. At the core of this quantum big data algorithm is a nonsparse matrix exponentiation technique for efficiently performing a matrix inversion of the training data inner-product (kernel) matrix.

Case studies approach for an undergraduate astrobiology course

NASA Astrophysics Data System (ADS)

Burko, Lior M.; Enger, Sandra

2013-04-01

Case studies is a well known and widely used method in law schools, medical schools, and business schools, but relatively little used in physics or astronomy courses. We developed an astrobiology course based strongly on the case studies approach, and after teaching it first at the University of Alabama in Huntsville, we have adapted it and are now teaching it at Alabama A&M University, a HBCU. The case studies approach uses several well tested and successful teaching methods - including group work, peer instruction, current interest topics, just-in-time teaching, &c. We have found that certain styles of cases are more popular among students than other styles, and will revise our cases to reflect such student preferences. We chose astrobiology -- an inherently multidisciplinary field -- because of the popularity of the subject matter, its frequent appearance in the popular media (news stories about searches for life in the universe, the discovery of Earth-like exoplanets, etc, in addition to SciFi movies and novels), and the rapid current progress in the field. In this talk we review briefly the case studies method, the styles of cases used in our astrobiology course, and student response to the course as found in our assessment analysis.

Students' Experience of Working with Socioscientific Issues - a Quantitative Study in Secondary School

NASA Astrophysics Data System (ADS)

Ottander, Christina; Ekborg, Margareta

2012-12-01

This research project aims to investigate how students in lower secondary school experience work with socioscientific issues (SSI). The six socioscientific cases developed and used in this project are relevant according to characteristics of SSI and to the national curriculum. Approximately 1,500 students in Sweden have worked with one SSI case chosen by the teachers. A questionnaire-based instrument was used to measure the affective domain of students' attitudes towards and interest in science before starting to work with the case and a second questionnaire after finishing a case. The second student questionnaire, measured the situational characteristics of the SSI work and perceived cognitive and affective outcomes. According to the students' self-reported experience, all cases were interesting and related to a current issue. Most cases were equally interesting to boys and girls, the only exception was You are what you eat, which girls found more interesting than boys did. Almost all students claim that they learnt new facts, learnt to argue for their standpoint and to search and evaluate information during the work with the cases. The girls' average scores were higher on several aspects of learning outcomes. Furthermore the students, especially the girls, perceived that the outcome of working with SSI had relevance for their future, with some cases more relevant than others. The more interesting the student found the case, the more they claimed they learnt. The students do not, however, claim that they learnt more science than during ordinary lessons.

Decay of solutions of the wave equation with arbitrary localized nonlinear damping

NASA Astrophysics Data System (ADS)

Bellassoued, Mourad

We study the problem of decay rate for the solutions of the initial-boundary value problem to the wave equation, governed by localized nonlinear dissipation and without any assumption on the dynamics (i.e., the control geometric condition is not satisfied). We treat separately the autonomous and the non-autonomous cases. Providing regular initial data, without any assumption on an observation subdomain, we prove that the energy decays at last, as fast as the logarithm of time. Our result is a generalization of Lebeau (in: A. Boutet de Monvel, V. Marchenko (Eds.), Algebraic and Geometric Methods in Mathematical Physics, Kluwer Academic Publishers, Dordrecht, the Netherlands, 1996, pp. 73) result in the autonomous case and Nakao (Adv. Math. Sci. Appl. 7 (1) (1997) 317) work in the non-autonomous case. In order to prove that result we use a new method based on the Fourier-Bross-Iaglintzer (FBI) transform.

Effectiveness of a Comprehensive Stress Management Program to Reduce Work-Related Stress in a Medium-Sized Enterprise

PubMed Central

2014-01-01

Objectives To assess the effectiveness of a comprehensive workplace stress management program consisting of participatory action-oriented training (PAOT) and individual management. Methods A comprehensive workplace stress management program was conducted in a medium-sized enterprise. The baseline survey was conducted in September 2011, using the Korean Occupational Stress Scale (KOSS) and Worker’s Stress Response Inventory (WSRI). After implementing both organizational and individual level interventions, the follow up evaluation was conducted in November 2011. Results Most of the workers participated in the organizational level PAOT and made Team-based improvement plans. Based on the stress survey, 24 workers were interviewed by a researcher. After the organizational and individual level interventions, there was a reduction of several adverse psychosocial factors and stress responses. In the case of blue-collar workers, psychosocial factors such as the physical environment, job demands, organizational system, lack of rewards, and occupational climate were significantly improved; in the case of white-collar workers, the occupational climate was improved. Conclusions In light of these results, we concluded that the comprehensive stress management program was effective in reducing work-related stress in a short-term period. A persistent long-term follow up is necessary to determine whether the observed effects are maintained over time. Both team-based improvement activities and individual interviews have to be sustainable and complementary to each other under the long-term plan. PMID:24524591

Problem-Based Learning: Using Ill-Structured Problems in Biology Project Work

ERIC Educational Resources Information Center

Chin, Christine; Chia, Li-Gek

2006-01-01

This case study involved year 9 students carrying out project work in biology via problem-based learning. The purpose of the study was to (a) find out how students approach and work through ill-structured problems, (b) identify some issues and challenges related to the use of such problems, and (c) offer some practical suggestions on the…

Correlates and perceived outcomes of four types of employee development activity.

PubMed

Birdi, K; Allan, C; Warr, P

1997-12-01

Participation in 4 different types of development activity was studied in a sample of manufacturing employees (N = 1,798). It was found that similar sets of variables were linked to greater participation in 3 activities: required training courses in work time, work-based development activity in work time, and career planning activity in work time or an individual's own time. Three kinds of reported benefits were studied, and the occurrence of these benefits was found to vary between different types of development activity. Overall job satisfaction and organizational commitment were significantly associated with prior participation in required training courses and work-based development activity. However, voluntary learning in one's own time was completely unrelated to these work attitudes.

Workers' compensation experience of North Carolina residential construction workers, 1986-1994.

PubMed

Dement, J M; Lipscomb, H

1999-02-01

A total of 31,113 workers' compensation claims among 7,400 North Carolina Homebuilders Association (NCHA) members and their subcontractors for the period 1986-1994 were analyzed to calculate workers' compensation claim incidence density rates. For the 7 years studied, the average rate (cases/200,000 work hours) for all claims was 16.40 and the rate for medical or lost time cases was 10.78. Highest rates for cases involving medical costs or paid lost time by mechanism of injury were observed for being struck by an object (3.1), lifting/movement (1.97), falls from a different level (1.13), striking against an object (0.87), and falls on the same level (0.46). Rates by mechanism of injury were highest for muscle strains (2.34), wounds/punctures (2.33), bruises/contusions (1.24), fractures/dislocations (0.98), and injuries to the eyes (0.81). Among medical cost or lost work time cases, body parts with highest injury rates were back/shoulders (1.99), fingers (1.31), leg/knee (1.00), hand/wrist (1.00), foot/ankle (0.86), and eyes (0.82). Injury rates were found to vary substantially among the residential construction trades. For more serious injuries involving medical costs greater than $2,000 or any lost work time, rates were highest for welders and cutters (28.1), insulators (24.3), roofers (19.4), and carpenters (15.3). The same general trends by trade were observed for cases involving paid lost time except that roofers were highest, with a rate of 9.1, followed by insulators (8.5), welders and cutters (5.8), and carpenters (5.8). Rates of falls from a different level resulting in medical costs or lost work time were highest for roofers (5.54), insulators (3.53), carpenters (2.05), and drywall installers (1.99). Descriptive information for falls from a different level resulting in paid lost time during 1993-1994 (n = 219) were reviewed to better determine the causes and circumstances of injuries. Falls from a roof accounted for 25.4 percent of the cases followed by falls involving scaffolds (23.9%) and ladders (20.6%), and falls from ceiling joists, floor joists, or framing (14.8%). Twenty-six work-related deaths occurred with vehicle accidents (n = 6) being the major known cause of death, followed by falls (n = 3), being struck by an object (n = 3), electric shock (n = 2), and contact with energy or chemicals (n = 2). Consistent with other analyses of workers' compensation data, chronic occupational diseases are not well captured in the workers' compensation claims among home builders; therefore, a companion study has examined mortality patterns among North Carolina construction workers.

HOROPLAN: computer-assisted nurse scheduling using constraint-based programming.

PubMed

Darmoni, S J; Fajner, A; Mahé, N; Leforestier, A; Vondracek, M; Stelian, O; Baldenweck, M

1995-01-01

Nurse scheduling is a difficult and time consuming task. The schedule has to determine the day to day shift assignments of each nurse for a specified period of time in a way that satisfies the given requirements as much as possible, taking into account the wishes of nurses as closely as possible. This paper presents a constraint-based, artificial intelligence approach by describing a prototype implementation developed with the Charme language and the first results of its use in the Rouen University Hospital. Horoplan implements a non-cyclical constraint-based scheduling, using some heuristics. Four levels of constraints were defined to give a maximum of flexibility: French level (e.g. number of worked hours in a year), hospital level (e.g. specific day-off), department level (e.g. specific shift) and care unit level (e.g. specific pattern for week-ends). Some constraints must always be verified and can not be overruled and some constraints can be overruled at a certain cost. Rescheduling is possible at any time specially in case of an unscheduled absence.

GPM Pre-Launch Algorithm Development for Physically-Based Falling Snow Retrievals

NASA Technical Reports Server (NTRS)

Jackson, Gail Skofronick; Tokay, Ali; Kramer, Anne W.; Hudak, David

2008-01-01

In this work we compare and correlate the long time series (Nov.-March) neasurements of precipitation rate from the Parsivels and 2DVD to the passive (89, 150, 183+/-1, +/-3, +/-7 GHz) observations of NOAA's AMSU-B radiometer. There are approximately 5-8 AMSU-B overpass views of the CARE site a day. We separate the comparisons into categories of no precipitation, liquid rain and falling snow precipitation. Scatterplots between the Parsivel snowfall rates and AMSU-B brightness temperatures (TBs) did not show an exploitable relationship for retrievals. We further compared and contrasted brightness temperatures to other surface measurements such as temperature and relative humidity with equally unsatisfying results. We found that there are similar TBs (especially at 89 and 150 GHz) for cases with falling snow and for non-precipitating cases. The comparisons indicate that surface emissivity contributions to the satellite observed TB over land can add uncertainty in detecting and estimating falling snow. The newest results show that the cloud icc scattering signal in the AMSU-B data call be detected by computing clear air TBs based on CARE radiosonde data and a rough estimate of surface emissivity. That is the differences in computed TI3 and AMSU-B TB for precipitating and nonprecipitating cases are unique such that the precipitating versus lon-precipitating cases can be identified. These results require that the radiosonde releases are within an hour of the AMSU-B data and allow for three surface types: no snow on the ground, less than 5 cm snow on the ground, and greater than 5 cm on the ground (as given by ground station data). Forest fraction and measured emissivities were combined to calculate the surface emissivities. The above work and future work to incorporate knowledge about falling snow retrievals into the framework of the expected GPM Bayesian retrievals will be described during this presentation.

[Reactive anxiety crisis: a unique case of work injury].

PubMed

Taino, G; Gazzoldi, T; Marandola, P; Valoti, E; Fabris, F; Imbriani, M

2007-01-01

The present study aims to describe a unique case in view of the disease diagnosed, the conditions of onset and the management by INAIL (Italian National Institute of Insurance for Injuries at Work and Occupational Diseases). A worker, after a verbal, animated dispute with some collegues, had an acute psychiatric agitation attack and went to the nearest emergency room, where he was investigated. No neuropsychiatric alteration was diagnosed, but based on anamnestic data, the physicians diagnosed an anxiety crisis reactive to work environment. A medical certificate for injury at work was produced and sent to the Insurance Board (INAIL). The worker was off work for 105 days diagnosed with a persistent anxious depressive syndrome, secondary to the traumatic event. INAIL reassessed the case later and confirmed only the first 30 days as due to work accident, while the following period was judged as related to affectivity disturbance due to common disease, not to work environment. Our case opens new perspective for the occupational physician in the assessment of ASD as work injury and of PTSD as professional disease, suggesting to give more attention to psychiatric health of workers.

EXAMINING TATOOINE: ATMOSPHERIC MODELS OF NEPTUNE-LIKE CIRCUMBINARY PLANETS

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, E. M.; Rauscher, E.

2016-08-01

Circumbinary planets experience a time-varying irradiation pattern as they orbit their two host stars. In this work, we present the first detailed study of the atmospheric effects of this irradiation pattern on known and hypothetical gaseous circumbinary planets. Using both a one-dimensional energy balance model (EBM) and a three-dimensional general circulation model (GCM), we look at the temperature differences between circumbinary planets and their equivalent single-star cases in order to determine the nature of the atmospheres of these planets. We find that for circumbinary planets on stable orbits around their host stars, temperature differences are on average no more thanmore » 1.0% in the most extreme cases. Based on detailed modeling with the GCM, we find that these temperature differences are not large enough to excite circulation differences between the two cases. We conclude that gaseous circumbinary planets can be treated as their equivalent single-star case in future atmospheric modeling efforts.« less

Neck postures in air traffic controllers with and without neck/shoulder disorders.

PubMed

Arvidsson, Inger; Hansson, Gert-Ake; Mathiassen, Svend Erik; Skerfving, Staffan

2008-03-01

Prolonged computer work with an extended neck is commonly believed to be associated with an increased risk of neck-shoulder disorders. The aim of this study was to compare neck postures during computer work between female cases with neck-shoulder disorders, and healthy referents. Based on physical examinations, 13 cases and 11 referents were selected among 70 female air traffic controllers with the same computer-based work tasks and identical workstations. Postures and movements were measured by inclinometers, placed on the forehead and upper back (C7/Th1) during authentic air traffic control. A recently developed method was applied to assess flexion/extension in the neck, calculated as the difference between head and upper back flexion/extension. cases and referents did not differ significantly in neck posture (median neck flexion/extension: -10 degrees vs. -9 degrees ; p=0.9). Hence, the belief that neck extension posture is associated with neck-shoulder disorders in computer work is not supported by the present data.

Job requirements compared to dental school education: impact of a case-based learning curriculum.

PubMed

Keeve, Philip L; Gerhards, Ute; Arnold, Wolfgang A; Zimmer, Stefan; Zöllner, Axel

2012-01-01

Case-based learning (CBL) is suggested as a key educational method of knowledge acquisition to improve dental education. The purpose of this study was to assess graduates from a patient-oriented, case-based learning (CBL)-based curriculum as regards to key competencies required at their professional activity. 407 graduates from a patient-oriented, case-based learning (CBL) dental curriculum who graduated between 1990 and 2006 were eligible for this study. 404 graduates were contacted between 2007 and 2008 to self-assess nine competencies as required at their day-to-day work and as taught in dental school on a 6-point Likert scale. Baseline demographics and clinical characteristics were presented as mean ± standard deviation (SD) for continuous variables. To determine whether dental education sufficiently covers the job requirements of physicians, we calculated the mean difference ∆ between the ratings of competencies as required in day-to-day work and as taught in medical school by subtracting those from each other (negative mean difference ∆ indicates deficit; positive mean difference ∆ indicates surplus). Spearman's rank correlation coefficient was calculated to reveal statistical significance (statistical significance p<0.05). 41.6% recipients of the questionnaire responded (n=168 graduates). A homogeneous distribution quantity of the graduate groups concerning gender, graduation date, professional experience and average examination grade was achieved.Comparing competencies required at work and taught in medical school, CBL was associated with benefits in "Research competence" (∆+0.6) "Interdisciplinary thinking" (∆+0.47), "Dental medical knowledge" (∆+0.43), "Practical dental skills" (∆+0.21), "Team work" (∆+0.16) and "Independent learning/working" (∆+0.08), whereas "Problem-solving skills" (∆-0.07), "Psycho-social competence" (∆-0.66) and "Business competence" (∆-2.86) needed improvement in the CBL-based curriculum. CBL demonstrated benefits with regard to competencies which were highly required in the job of dentists. Psycho-social and business competence deserve closer attention in future curricular development.

Design and implementation of a cost-accounting system in hospital pharmacy.

PubMed

Gouveia, W A; Anderson, E R; Decker, E L; Backer, K

1988-03-01

The design and implementation of a cost-accounting system in a hospital pharmacy department is described. Pharmacy resource use (labor, drugs, supplies, and overhead), or pharmacy's intermediate products, was clearly defined in terms of dosage forms (10 groupings representing variable labor and supplies) and drug products (more than 100 categories that incorporate cost and volume of use for 3000 line items). Costs were defined as variable or nonvariable (fixed), based on whether they were related to a specific medication order. Labor was divided into variable and fixed components. Time standards were developed using time and motion studies. Variable labor hours were determined as follows: specified hours (the volume of each dosage form multiplied by the standard time for each dosage form); nonspecified hours (time not directly associated with production); hours worked (specified plus nonspecified hours); and hours paid (hours worked plus sick leave and vacation). A standard cost for each drug product was based on the weighted average of volume and cost of the individual line items. The total drug budget was constructed by multiplying the standard cost for each drug product times the projected volume for each drug product. The pharmacy budget was developed by calculating the number and mix of pharmacy products used in association with the projected number and type of cases for the fiscal year. The monthly pharmacy budget reports were assembled with data from the payroll, billing, and cost-accounting systems.(ABSTRACT TRUNCATED AT 250 WORDS)

Brain-Inspired Photonic Signal Processor for Generating Periodic Patterns and Emulating Chaotic Systems

NASA Astrophysics Data System (ADS)

Antonik, Piotr; Haelterman, Marc; Massar, Serge

2017-05-01

Reservoir computing is a bioinspired computing paradigm for processing time-dependent signals. Its hardware implementations have received much attention because of their simplicity and remarkable performance on a series of benchmark tasks. In previous experiments, the output was uncoupled from the system and, in most cases, simply computed off-line on a postprocessing computer. However, numerical investigations have shown that feeding the output back into the reservoir opens the possibility of long-horizon time-series forecasting. Here, we present a photonic reservoir computer with output feedback, and we demonstrate its capacity to generate periodic time series and to emulate chaotic systems. We study in detail the effect of experimental noise on system performance. In the case of chaotic systems, we introduce several metrics, based on standard signal-processing techniques, to evaluate the quality of the emulation. Our work significantly enlarges the range of tasks that can be solved by hardware reservoir computers and, therefore, the range of applications they could potentially tackle. It also raises interesting questions in nonlinear dynamics and chaos theory.