Design and synthesis of inorganic/organic hybrid electrochemical materials

NASA Astrophysics Data System (ADS)

Harreld, John H.

An ambient pressure method for drying sol-gel materials is developed to synthesize high porosity (80--90%), high surface area vanadium oxide and silica aerogel materials (150--300 and 1000 m2/g for vanadium pentoxide and silica, respectively). The synthesis approach uses liquid exchange to replace the pore fluid with a low surface tension, nonpolar solvent which reduces the capillary pressures developed during drying. The Good-Girifalco interaction parameter is used to calculate pore stresses resulting from drying silica gels from various liquids. Vanadium oxide/polypyrrole hybrid aerogels are prepared using three strategies. These approaches focus on either sequential or consecutive polymerization of the inorganic and organic networks. Microcomposite aerogels are synthesized by encapsulating a dispersion of preformed polypyrrole in a vanadium pentoxide gel. In the second approach, pyrrole is polymerized and doped within the pore volume of preformed vanadium pentoxide gel. When the inorganic and organic precursors are polymerized simultaneously, the resulting gels exhibited a nanometer scaled microstructure with homogeneous distributions of either phases. Through this route, a suitable microstructure and composition for a lithium secondary battery cathode is obtained. Lithiated aerogels of hydrated nickel, cobalt, and mixed nickel-cobalt oxides are synthesized from lithium hydroxide and transition metal acetate precursors. The XRD analyses indicate that the nickel containing gels exhibit a lithium deficiency (less than 1 Li/transition metal. By increasing the concentration of the lithium precursor the lithium content in nickel oxides is increased, and additional base solution is no longer required to catalyze gelation. A non-hydrolytic sol-gel approach is utilized to create tin oxide and tin-aluminum binary oxide aerogels with high porosity (90%) and high surface area (300 m2/g). XRD data from single phase tin oxide aerogel indicates the growth of SnO2 crystallites between 150--400°C in air, accompanied by a reduction in surface area (30 m2/g). Heated tin oxide aerogel exhibits comparable reversible specific capacity (390 mAh/g) as that of commercial SnO2 (420 mAh/g). Amorphous tin oxide aerogel is stabilized to higher temperatures when aluminum oxide is incorporated into the structure. The tin oxide phase remains electrochemically active towards lithium insertion and exhibits excellent reversibility during cycling.

L-cysteine capped lanthanum hydroxide nanostructures for non-invasive detection of oral cancer biomarker.

PubMed

Tiwari, Sachchidanand; Gupta, Pramod K; Bagbi, Yana; Sarkar, Tamal; Solanki, Pratima R

2017-03-15

In this paper, we present the result of studies related to the in situ synthesis of amino acid (L-Cysteine) capped lanthanum hydroxide nanoparticles [Cys-La(OH) 3 NPs] towards the fabrication of efficient immunosensor for non-invasive detection of oral cancer. The characterization of Cys-La(OH) 3 NPs was carried out by different techniques including X-ray diffraction, scanning electron microscopy, transmission electron microscopy, fourier transform infrared spectroscopy and electrochemical techniques. These Cys-La(OH) 3 NPs were electrophoretically deposited onto an indium-tin-oxide glass substrate and used for immobilization of anti-cytokeratin fragment-21-1 (anti-Cyfra-21-1) for the electrochemical detection of Cyfra-21-1. This immunosensor shows a broad detection range of 0.001-10.2ngmL -1 , the low detection limit of 0.001ngmL -1 , and high sensitivity of 12.044µA (ng per mL cm -2 ) -1 with a response time of 5min. This immunosensor was found to be more advanced in terms of high sensitivity and low detection limit as compared to previously reported biosensors and commercially available ELISA kit (Kinesis DX). Copyright © 2016 Elsevier B.V. All rights reserved.

New SnO2/MgAl-layered double hydroxide composites as photocatalysts for cationic dyes bleaching.

PubMed

Dvininov, E; Ignat, M; Barvinschi, P; Smithers, M A; Popovici, E

2010-05-15

A new type of nanocomposite containing SnO(2) has been obtained by wet impregnation of dehydrated Mg/Al-hydrotalcite-type compounds with ethanolic solutions of SnCl(4).2H(2)O. Tin chloride hydrolysis was achieved using NaOH or NH(4)OH aqueous solutions, at pH around 9, followed by the conversion into corresponding hydroxides through calcinations. The powder X-ray diffraction (PXRD) and UV-Vis diffuse reflectance (UV-DR) methods confirmed the structure of as-synthesized solids. The chemical composition and morphology of the synthesized materials were investigated by energy dispersive X-ray analysis (EDX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The as-synthesized materials were used for photocatalytic studies showing a good activity for methylene blue decolourization, which varies with SnO(2) content and used as a hydrolysing agent. The proposed mechanism is based on the shifting of flat band potential of SnO(2) due to the interaction with Mg/Al-LDH, this being energetically favourable to the formation of hydroxyl radicals responsible for methylene blue degradation. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Low-temperature sintering behavior of nanocrystalline indium tin oxide prepared from polymer-containing sols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koroesi, Laszlo, E-mail: l.korosi@chem.u-szeged.hu; Papp, Szilvia; Oszko, Albert

2012-04-15

Highlights: Black-Right-Pointing-Pointer The synthesis of ITO powders and thin films from PVP-containing sols is presented. Black-Right-Pointing-Pointer The nano- and microstructures of ITO are more compact when PVP is used. Black-Right-Pointing-Pointer PVP acts both as a steric stabilizer of the sol and as a pre-sintering agent. Black-Right-Pointing-Pointer The PVP-induced enhanced sintering results in ITO with lower electrical resistance. Black-Right-Pointing-Pointer The surface composition of the ITO films is independent of the initial PVP content. -- Abstract: Indium tin hydroxide (ITH) xerogel powders and thin films with different polyvinylpyrrolidone (PVP) contents (0-22%, w/w) were prepared by a classical sol-gel method. To obtain nanocrystallinemore » indium tin oxide (ITO), the ITH xerogels were calcined at 550 Degree-Sign C. The effect of the initial polymer content on the structure of the ITO powders was studied by means of N{sub 2}-sorption measurements, small-angle X-ray scattering (SAXS), transmission and scanning electron microscopy. The N{sub 2}-sorption measurements revealed that the ITO powders obtained contained micropores and both their porosity and specific surface area decreased with increasing PVP content of the ITH xerogels. The SAXS measurements confirmed the enhanced sintering of the particles in the presence of PVP. The calculated mass fractal dimensions of the ITO powders increased significantly, indicating a significant compaction in structure. The pre-sintered structure could be achieved at relatively low temperature, which induced a significant decreasing (three orders of magnitude) in the electrical resistance of the ITO films.« less

Electrophoretic formation of semiconductor layers with adjustable band gap

NASA Astrophysics Data System (ADS)

Shindrov, Alexander; Yuvchenko, Sergey; Vikulova, Maria; Tretyachenko, Elena; Zimnyakov, Dmitry; Gorokhovsky, Alexander

2017-11-01

The ceramic layers of the potassium polytitanates modified by transition metal salts were electrophoretically deposited onto the surface of glassy substrate coated with indium-tin oxide. The deposition allows obtaining a dense ceramic layer formed by composite agglomerates consisting of nanoscale particles with average size of 130-190 nm. The optical absorption spectra of the coatings modified in the mixtures of aqueous solutions of different transition metal salts were investigated. It was recognized that a bandgap value of these composites can be adjusted in a range from 1.4 to 2.3 eV depending the chemical composition of layered double hydroxide obtained during modification. This might be very promising for optoelectronic applications of such coatings due to an explicit control of optical properties.

Recovery of copper from PVC multiwire cable waste by steam gasification.

PubMed

Zabłocka-Malicka, Monika; Rutkowski, Piotr; Szczepaniak, Włodzimierz

2015-12-01

Screened multiwire, PVC insulated tinned copper cable was gasified with steam at high temperature (HTSG) under atmospheric pressure for recovery of cooper. Gases from the process were additionally equilibrated at 850°C on the bed of calcined clay granules and more than 98% of C+H content in the cable was transformed to non-condensing species. Granules prepared from local clay were generally resistant for chlorination, there was also almost no deposition of metals, Cu and Sn, on the catalytic bed. It was found that 28% of chlorine reacted to form CaCl2, 71% was retained in aqueous condensate and only 0.6% was absorbed in alkaline scrubber. More than 99% of calcium existed in the process solid residue as a mixture of calcium chloride and calcium oxide/hydroxide. PVC and other hydrocarbon constituents were completely removed from the cable sample. Copper was preserved in original form and volatilization of copper species appeared insignificant. Tin was alloying with copper and its volatilization was less than 1%. Fractionation and speciation of metals, chlorine and calcium were discussed on the basis of equilibrium model calculated with HSC Chemistry software. High temperature steam gasification prevents direct use of the air and steam/water is in the process simultaneously gaseous carrier and reagent, which may be recycled together with hydrocarbon condensates. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oxygen reduction reaction (ORR) on mixed oxy-nitride non-noble catalyst: Ab-initio simulation, elaboration and characterization

NASA Astrophysics Data System (ADS)

Seifitokaldani, Ali

In this project, titanium oxy-nitride (TiOxN y) has been studied as a new non-noble electrocatalyst for the oxygen reduction reaction (ORR). A comprehensive comparison between four different sol-gel methods was carried out to evaluate the physicochemical and electrochemical properties of the produced electro-catalysts. Among them, a new urea-based sol-gel method (simply called U method) is introduced to prepare TiOxNy at a fairly low temperature and duration, with higher electro-catalytic activity for the ORR. The prepared electro-catalysts with different N/O ratios showed different properties from a less conductive behavior in oxygen-rich (low N/O ratio) materials to more conductive electro-catalyst behavior in nitrogen-rich (high N/O ratio) oxy-nitrides, respectively. Generally, electro-catalysts prepared by the U method had more titanium nitride in their structures than the electro-catalysts prepared by the other methods. Nevertheless, heat treatment had a key role in this phase transferring from having high oxide structure to high nitride structure. According to the elemental analysis done by energy dispersive spectroscopy (EDS), nitrogen percentage in the bulk material increased from 9 to 24 percent by increasing the temperature from 700 to 1100 °C, while the oxygen percentage was decreasing inversely. In addition, based on the X-ray diffraction (XRD) data, in the case of U method, the TiN characteristic peaks were obvious, even at lower temperatures. Increasing the temperature also made the peaks much sharper indicating the growth of the crystallite size. The calculated crystallite size showed the crystallite size of samples prepared by U method (20 to 40 nm) was almost in the same range of the TiN crystallite size, but the crystallite size of the samples prepared by the other sol-gel methods (40 to 60 nm) was in the same range of the TiO2 crystallite size. Scanning electron microscopy (SEM) and B.E.T. surface area analyzer were used to evaluate the particle size and surface area of different samples, respectively. They indicated a smaller particle size and a higher surface area in the electro-catalysts produced by the U method. Besides the aforementioned physicochemical characterizations, cyclic voltammetry (CV), polarization, and electrochemical impedance spectroscopy (EIS) were used to evaluate the electrochemical properties of the electro-catalysts. Obtained Tafel slope, exchange current density and onset potential revealed that the electro-catalyst prepared by the U method which was annealed at 1100 °C, had the best electro-catalytic activity among all other samples with Tafel slope of -203 mV/decade, exchange current density around 4E-04 mA/mg and the onset potential close to 0.8 volt vs. NHE (normal hydrogen electrode). EIS measurements also supported this assertion through revealing the highest specific capacitance (˜ 3.3 F/g). This result was in agreement with the highest B.E.T. surface area and the lowest charge transfer resistance exhibited by this electro-catalyst among the other samples. Stability is one of the determinant factors in selecting an electro-catalyst for the ORR. In this regard, ICP-TOF-MS was used to evaluate the chemical stability of the prepared electro-catalysts under corrosive acidic environment, by measuring the concentration of the dissolved titanium after a certain time. Heretofore, measuring the dissolved metal concentration by ICP-TOF-MS was done just to evaluate its chemical stability. However, in this project this technique was also used during the CV, to evaluate the electro-catalyst's electrochemical stability as well, which is more realistic and similar to the PEMFC's working condition. Stability of the best electrocatalyst with the highest catalytic activity (prepared by the U method) was better than the commercially used Pt/C electro-catalyst, both chemically and electrochemically. Electrochemical stability of the prepared electro-catalysts has also been studied at a high oxidizing potential (more than 2 volts vs. NHE). X-ray Photoelectron Spectroscopy (XPS) showed that the nitrogen amount on the surface of the electro-catalyst decreased from 11 % before the oxidation to 5 % after the oxidation, whereas the catalytic activity for the ORR decreased after the oxidation. Thus, decreasing the titanium nitride's amount in the titanium oxy-nitride surface reduced its catalytic activity. In the second phase of this project, electro-catalytic activity of the titanium nitride for the ORR was investigated via a density functional theory (DFT) computation. To the best of our knowledge, there is no theoretical and computational quantum chemistry study of the transition metal's nitride as the electro-catalyst in PEM fuel cells. ORR was considered to take place in three different sequential steps namely oxygen adsorption, hydroxide production and water desorption. Based on the XRD results, TiN(111) and TiN(200) were considered as the two major facets of the TiN. Simulation was done by the Vienna ab initio Simulation Package (VASP) based on the Plane-Wave basis sets and periodic boundary condition, while the PBE exchangecorrelational functional was used to describe the interactions among electrons. Comparing the adsorption energies proved existence of a strong dissociative adsorption of oxygen on the TiN(111) regardless of the adsorption sites. However, because of a relatively strong OH adsorption, TiN(111) loses the active sites to proceed the ORR, while on the TiN(200) surface, water production and desorption came about easily. Electron density of states (DOS) was obtained to calculate the d-band center and fractional filling in different situations. Considering two possible bridge and top adsorption sites on the TiN(200), these information indicated the hydroxide production and water desorption as the rate determining steps for the ORR in bridge and top sites, respectively. Therefore, it was shown that the TiN, specially TiN(200) had exhibited good electro-catalytic activity for the ORR. Losing this TiN amount from the titanium oxy-nitride's surface might be responsible for the decrease of the electro-catalytic activity of the titanium oxy-nitride for the ORR.

Role of iron and aluminum coagulant metal residuals and lead release from drinking water pipe materials.

PubMed

Knowles, Alisha D; Nguyen, Caroline K; Edwards, Marc A; Stoddart, Amina; McIlwain, Brad; Gagnon, Graham A

2015-01-01

Bench-scale experiments investigated the role of iron and aluminum residuals in lead release in a low alkalinity and high (> 0.5) chloride-to-sulfate mass ratio (CSMR) in water. Lead leaching was examined for two lead-bearing plumbing materials, including harvested lead pipe and new lead: tin solder, after exposure to water with simulated aluminum sulfate, polyaluminum chloride and ferric sulfate coagulation treatments with 1-25-μM levels of iron or aluminum residuals in the water. The release of lead from systems with harvested lead pipe was highly correlated with levels of residual aluminum or iron present in samples (R(2) = 0.66-0.88), consistent with sorption of lead onto the aluminum and iron hydroxides during stagnation. The results indicate that aluminum and iron coagulant residuals, at levels complying with recommended guidelines, can sometimes play a significant role in lead mobilization from premise plumbing.

A molecular approach to self-supported cobalt-substituted ZnO materials as remarkably stable electrocatalysts for water oxidation.

PubMed

Pfrommer, Johannes; Lublow, Michael; Azarpira, Anahita; Göbel, Caren; Lücke, Marcel; Steigert, Alexander; Pogrzeba, Martin; Menezes, Prashanth W; Fischer, Anna; Schedel-Niedrig, Thomas; Driess, Matthias

2014-05-12

In regard to earth-abundant cobalt water oxidation catalysts, very recent findings show the reorganization of the materials to amorphous active phases under catalytic conditions. To further understand this concept, a unique cobalt-substituted crystalline zinc oxide (Co:ZnO) precatalyst has been synthesized by low-temperature solvolysis of molecular heterobimetallic Co(4-x)Zn(x) O4 (x = 1-3) precursors in benzylamine. Its electrophoretic deposition onto fluorinated tin oxide electrodes leads after oxidative conditioning to an amorphous self-supported water-oxidation electrocatalyst, which was observed by HR-TEM on FIB lamellas of the EPD layers. The Co-rich hydroxide-oxidic electrocatalyst performs at very low overpotentials (512 mV at pH 7; 330 mV at pH 12), while chronoamperometry shows a stable catalytic current over several hours. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

INTERIM RESULTS FROM A STUDY OF THE IMPACTS OF TIN(II) BASED MERCURY TREATMENT IN A SMALL STREAM ECOSYSTEM: TIMS BRANCH, SAVANNAH RIVER SITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Looney, B.; Bryan, L.; Mathews, T.

2012-03-30

Mercury (Hg) has been identified as a 'persistent, bioaccumulative and toxic' pollutant with widespread impacts throughout North America and the world (EPA. 1997a, 1997b, 1998a, 1998b, 2000). Although most of the mercury in the environment is inorganic Hg, a small proportion of total Hg is transformed through the actions of aquatic microbes into methylmercury (MeHg). In contrast to virtually all other metals, MeHg biomagnifies or becomes increasingly concentrated as it is transferred through aquatic food chains so that the consumption of mercury contaminated fish is the primary route of this toxin to humans. For this reason, the ambient water qualitymore » criterion (AWQC) for mercury is based on a fish tissue endpoint rather than an aqueous Hg concentration, as the tissue concentration (e.g., < 0.3 {mu}g/g fillet) is considered to be a more consistent indicator of exposure and risk (EPA, 2001). Effective mercury remediation at point-source contaminated sites requires an understanding of the nature and magnitude of mercury inputs, and also knowledge of how these inputs must be controlled in order to achieve the desired reduction of mercury contamination in biota necessary for compliance with AWQC targets. One of the challenges to remediation is that mercury body burdens in fish are more closely linked to aqueous MeHg than to inorganic Hg concentrations (Sveinsdottir and Mason 2005), but MeHg production is not easily predicted or controlled. At point-source contaminated sites, mercury methylation is not only affected by the absolute mercury load, but also by the form of mercury loaded. In addition, once MeHg is formed, the hydrology, trophic structure, and water chemistry of a given system affect how it is transformed and transferred through the food chain to fish. Decreasing inorganic Hg concentrations and loading may often therefore be a more achievable remediation goal, but has led to mixed results in terms of responses in fish bioaccumulation. A number of source control measures have resulted in rapid responses in lake or reservoir fisheries (Joslin 1994, Turner and Southworth 1999; Orihel et al., 2007), but examples of similar responses in Hg-contaminated stream ecosystems are less common. Recent work suggests that stream systems may actually be more susceptible to mercury bioaccumulation than lakes, highlighting the need to better understand the ecological drivers of mercury bioaccumulation in stream-dwelling fish (Chasar et al. 2009, Ward et al. 2010). In the present study we examine the response of fish to remedial actions in Tims Branch, a point-source contaminated stream on the Department of Energy's (DOE) Savannah River Site in Aiken, South Carolina. This second order stream received inorganic mercury inputs at its headwaters from the 1950s-2000s which contaminated the water, sediments, and biota downstream. In 2007, an innovative mercury removal system using tin (II) chloride (stannous chloride, SnCl{sub 2}) was implemented at a pre-existing air stripper. Tin(II) reduces dissolved Hg (II) to Hg (0), which is removed by the air stripper. During this process, tin(II) is oxidized to tin (IV) which is expected to precipitate as colloidal tin(IV) oxides and hydroxides, particulate materials with relatively low toxicity (Hallas and Cooney, 1981, EPA 2002, ATSDR, 2005). The objectives of the present research are to provide an initial assessment of the net impacts of the tin(II) based mercury treatment on key biota and to document the distribution and fate of inorganic tin in this small stream ecosystem after the first several years of operating a full scale system. To support these objectives, we collected fish, sediment, water, invertebrates, and biofilm samples from Tims Branch to quantify the general behavior and accumulation patterns for mercury and tin in the ecosystem and to determine if the treatment process has resulted in: (1) a measurable beneficial impact on (i.e., decrease of) mercury concentration in upper trophic level fish and other biota; this is a key environmental endpoint since reducing mercury concentration in fish is a primary regulatory driver for controlling mercury in streams; and (2) the potential for negative impacts associated with inorganic tin, including, biological transformation and uptake, and/or undesirable accumulation/focusing of tin to in key ecosystem compartments.« less

Photocatalytic water oxidation with iron oxide hydroxide (rust) nanoparticles

NASA Astrophysics Data System (ADS)

Shelton, Timothy L.; Bensema, Bronwyn L.; Brune, Nicholas K.; Wong, Christopher; Yeh, Max; Osterloh, Frank E.

2017-01-01

Hematite has attracted considerable interest as a photoanode material for water oxidation under visible illumination. Here, we explore the limits of photocatalytic water oxidation activity with iron (III) oxide hydroxide nanocrystals and NaIO4 as a sacrificial electron acceptor (E=1.63 V NHE at pH=0.5). The sol was prepared by hydrolysis of FeCl3 in boiling 0.002-M HCl solution and confirmed to mainly consist of ß-FeO(OH) (akaganéite) particles with 5 to 15 nm diameter. From a 0.01 M aqueous NaIO4 solution, the sol evolves between 4.5 and 35.2 μmol O2 h-1, depending on pH, light intensity (>400 nm, 290 to 700 mW cm-2), ß-FeO(OH), and NaIO4 concentration. The activity increases with pH, and depends linearly on light intensity and photocatalyst amount, and it varies with sacrificial electron donor concentration. Under optimized conditions, the apparent quantum efficiency is 0.19% (at 400 nm and 460 mW cm-2), and the turnover number is 2.58 based on total ß-FeO(OH). Overall, the efficiency of the ß-FeO(OH)/NaIO4 photocatalytic system is limited by electron hole recombination and by particle aggregation over longer irradiation times (24 h). Lastly, surface photovoltage measurements on ß-FeO(OH) films on fluorine doped tin oxide substrate confirm a 2.15 eV effective band gap for the material.

Application of granular ferric hydroxides for removal elevated concentrations of arsenic from mine waters

NASA Astrophysics Data System (ADS)

Szlachta, Małgorzata; Włodarczyk, Paweł; Wójtowicz, Patryk

2015-04-01

Arsenic is naturally occurring element in the environment. Over three hundred minerals are known to contain some form of arsenic and among them arsenopyrite is the most common one. Arsenic-bearing minerals are frequently associated with ores containing mined metals such as copper, tin, nickel, lead, uranium, zinc, cobalt, platinum and gold. In the aquatic environment arsenic is typically present in inorganic forms, mainly in two oxidation states (+5, +3). As(III) is dominant in more reduced conditions, whereas As(V) is mostly present in an oxidizing environment. However, due to certain human activities the elevated arsenic levels in aquatic ecosystems are arising to a serious environmental problem. High arsenic concentrations found in surface and groundwaters, in some regions originate from mining activities and ore processing. Therefore, the major concern of mining industry is to maintain a good quality of effluents discharged in large volumes. This requires constant monitoring of effluents quality that guarantee the efficient protection of the receiving waters and reacting to possible negative impact of contamination on local communities. A number of proven technologies are available for arsenic removal from waters and wastewaters. In the presented work special attention is given to the adsorption method as a technically feasible, commonly applied and effective technique for the treatment of arsenic rich mine effluents. It is know that arsenic has a strong affinity towards iron rich materials. Thus, in this study the granular ferric hydroxides (CFH 12, provided by Kemira Oyj, Finland) was applied to remove As(III) and As(V) from aqueous solutions. The batch adsorption experiments were carried out to assess the efficiency of the tested Fe-based material under various operating parameters, including composition of treated water, solution pH and temperature. The results obtained from the fixed bed adsorption tests demonstrated the benefits of applying granular ferric hydroxides for treatment As-contaminated waters. This research is a part of the study supported by the National Centre for Research and Development grant (2014-2017) "Sustainable and responsible supply of primary resources - SUSMIN" (http://projects.gtk.fi/susmin), within the EU ERA-NET ERA-MIN program.

10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

Code of Federal Regulations, 2012 CFR

2012-01-01

... Indium-115 100 Indium-116m 1,000 Indium-117m 1,000 Indium-117 1,000 Indium-119m 1,000 Tin-110 100 Tin-111 1,000 Tin-113 100 Tin-117m 100 Tin-119m 100 Tin-121m 100 Tin-121 1,000 Tin-123m 1,000 Tin-123 10 Tin-125 10 Tin-126 10 Tin-127 1,000 Tin-128 1,000 Antimony-115 1,000 Antimony-116m 1,000 Antimony-116 1...

Crystal structure of tetra­wickmanite, Mn2+Sn4+(OH)6

PubMed Central

Lafuente, Barbara; Yang, Hexiong; Downs, Robert T.

2015-01-01

The crystal structure of tetra­wickmanite, ideally Mn2+Sn4+(OH)6 [mangan­ese(II) tin(IV) hexa­hydroxide], has been determined based on single-crystal X-ray diffraction data collected from a natural sample from Långban, Sweden. Tetra­wickmanite belongs to the octa­hedral-framework group of hydroxide-perovskite minerals, described by the general formula BB’(OH)6 with a perovskite derivative structure. The structure differs from that of an ABO3 perovskite in that the A site is empty while each O atom is bonded to an H atom. The perovskite B-type cations split into ordered B and B′ sites, which are occupied by Mn2+ and Sn4+, respectively. Tetra­wickmanite exhibits tetra­gonal symmetry and is topologically similar to its cubic polymorph, wickmanite. The tetra­wickmanite structure is characterized by a framework of alternating corner-linked [Mn2+(OH)6] and [Sn4+(OH)6] octa­hedra, both with point-group symmetry -1. Four of the five distinct H atoms in the structure are statistically disordered. The vacant A site is in a cavity in the centre of a distorted cube formed by eight octa­hedra at the corners. However, the hydrogen-atom positions and their hydrogen bonds are not equivalent in every cavity, resulting in two distinct environments. One of the cavities contains a ring of four hydrogen bonds, similar to that found in wickmanite, while the other cavity is more distorted and forms crankshaft-type chains of hydrogen bonds, as previously proposed for tetra­gonal stottite, Fe2+Ge4+(OH)6. PMID:25878828

The C-Terminal Extension Unique to the Long Isoform of the Shelterin Component TIN2 Enhances Its Interaction with TRF2 in a Phosphorylation- and Dyskeratosis Congenita Cluster-Dependent Fashion.

PubMed

Nelson, Nya D; Dodson, Lois M; Escudero, Laura; Sukumar, Ann T; Williams, Christopher L; Mihalek, Ivana; Baldan, Alessandro; Baird, Duncan M; Bertuch, Alison A

2018-06-15

TIN2 is central to the shelterin complex, linking the telomeric proteins TRF1 and TRF2 with TPP1/POT1. Mutations in TINF2 , which encodes TIN2, that are found in dyskeratosis congenita (DC) result in very short telomeres and cluster in a region shared by the two TIN2 isoforms, TIN2S (short) and TIN2L (long). Here we show that TIN2L, but not TIN2S, is phosphorylated. TRF2 interacts more with TIN2L than TIN2S, and both the DC cluster and phosphorylation promote this enhanced interaction. The binding of TIN2L, but not TIN2S, is affected by TRF2-F120, which is also required for TRF2's interaction with end processing factors such as Apollo. Conversely, TRF1 interacts more with TIN2S than with TIN2L. A DC-associated mutation further reduces TIN2L-TRF1, but not TIN2S-TRF1, interaction. Cells overexpressing TIN2L or phosphomimetic TIN2L are permissive to telomere elongation, whereas cells overexpressing TIN2S or phosphodead TIN2L are not. Telomere lengths are unchanged in cell lines in which TIN2L expression has been eliminated by clustered regularly interspaced short palindromic repeat (CRISPR)/Cas9-mediated mutation. These results indicate that TIN2 isoforms are biochemically and functionally distinguishable and that shelterin composition could be fundamentally altered in patients with TINF2 mutations. Copyright © 2018 Nelson et al.

Process for removal of mineral particulates from coal-derived liquids

DOEpatents

McDowell, William J.

1980-01-01

Suspended mineral solids are separated from a coal-derived liquid containing the solids by a process comprising the steps of: (a) contacting said coal-derived liquid containing solids with a molten additive having a melting point of 100.degree.-500.degree. C. in an amount of up to 50 wt. % with respect to said coal-derived liquid containing solids, said solids present in an amount effective to increase the particle size of said mineral solids and comprising material or mixtures of material selected from the group of alkali metal hydroxides and inorganic salts having antimony, tin, lithium, sodium, potassium, magnesium, calcium, beryllium, aluminum, zinc, molybdenum, cobalt, nickel, ruthenium, rhodium or iron cations and chloride, iodide, bromide, sulfate, phosphate, borate, carbonate, sulfite, or silicate anions; and (b) maintaining said coal-derived liquid in contact with said molten additive for sufficient time to permit said mineral matter to agglomerate, thereby increasing the mean particle size of said mineral solids; and (c) recovering a coal-derived liquid product having reduced mineral solids content. The process can be carried out with less than 5 wt. % additive and in the absence of hydrogen pressure.

Determination of butyltins, phenyltins and octyltins in foods with preservation of their moieties: A critical review on analytical methods.

PubMed

Chung, Stephen W C; Wu, Andy H T

2017-07-07

Tributyltin and triphenyltin have been extensively applied in anti-fouling paints since the 1960s. Hence, organotin compounds (OTCs), especially butyltins and phenyltins, in seafood has been of concern for decades. Even though the "International Convention on the Control of Harmful Anti-Fouling Systems on Ships, 2001" entered into force internationally in 2008 and prohibited the use of OTCs in anti-fouling paints used on ships, the analysis of OTCs in seafood was not commonly included in routine monitoring programmes. Besides, species of triphenyltin, including triphenyltin hydroxide and acetate, have been used as pesticides and may accumulate in food. Moreover, the European Food Safety Agency established a group tolerable daily intake for tributyltin, dibutyltin, triphenyltin and dioctyltin in 2004 as they exert their immunotoxic effects by similar mode of action and potency. Therefore, suitable methods are needed to analyze butyl-, phenyl- and octyl-tins simultaneously in food without affecting their moieties. This review aims to provide background information in this area. Copyright © 2017 Elsevier B.V. All rights reserved.

Aluminum Hydroxide and Magnesium Hydroxide

MedlinePlus

Aluminum Hydroxide, Magnesium Hydroxide are antacids used together to relieve heartburn, acid indigestion, and upset stomach. They ... They combine with stomach acid and neutralize it. Aluminum Hydroxide, Magnesium Hydroxide are available without a prescription. ...

Methods of using adsorption media for separating or removing constituents

DOEpatents

Tranter, Troy J [Idaho Falls, ID; Herbst, R Scott [Idaho Falls, ID; Mann, Nicholas R [Blackfoot, ID; Todd, Terry A [Aberdeen, ID

2011-10-25

Methods of using an adsorption medium to remove at least one constituent from a feed stream. The method comprises contacting an adsorption medium with a feed stream comprising at least one constituent and removing the at least one constituent from the feed stream. The adsorption medium comprises a polyacrylonitrile (PAN) matrix and at least one metal hydroxide homogenously dispersed therein. The adsorption medium may comprise from approximately 15 wt % to approximately 90 wt % of the PAN and from approximately 10 wt % to approximately 85 wt % of the at least one metal hydroxide. The at least one metal hydroxide may be selected from the group consisting of ferric hydroxide, zirconium hydroxide, lanthanum hydroxide, cerium hydroxide, titanium hydroxide, copper hydroxide, antimony hydroxide, and molybdenum hydroxide.

Synthesis and Characterization of Tin(IV) Oxide Obtained by Chemical Vapor Deposition Method

NASA Astrophysics Data System (ADS)

Nagirnyak, Svitlana V.; Lutz, Victoriya A.; Dontsova, Tatiana A.; Astrelin, Igor M.

2016-07-01

The effect of precursors on the characteristics of tin oxide obtained by chemical vapor deposition (CVD) method was investigated. The synthesis of nanosized tin(IV) oxide was carried out with the use of two different precursors: tin(II) oxalate obtained using tin chloride(II) and oxalic acid; tin(II) oxalate obtained using tin chloride(II); and ammonium oxalate. The synthesized tin(IV) oxide samples were studied by electron microscopy, X-ray diffraction and optical spectra. The lattice parameters of tin(IV) oxide samples were defined, the bandgap of samples were calculated.

International strategic minerals inventory summary report; tin

USGS Publications Warehouse

Sutphin, D.M.; Sabin, A.E.; Reed, B.L.

1990-01-01

The International Strategic Minerals Inventory tin inventory contains records for 56 major tin deposits and districts in 21 countries. These countries accounted for 98 percent of the 10 million metric tons of tin produced in the period 1934-87. Tin is a good alloying metal and is generally nontoxic, and its chief uses are as tinplate for tin cans and as solder in electronics. The 56 locations consist of 39 lode deposits and 17 placers and contain almost 7.5 million metric tons of tin in identified economic resources (R1E) and another 1.5 million metric tons of tin in other resource categories. Most of these resources are in major deposits that have been known for over a hundred years. Lode deposits account for 44 percent of the R1E and 87 percent of the resources in other categories. Placer deposits make up the remainder. Low-income and middle-income countries, including Bolivia and Brazil and countries along the Southeast Asian Tin Belt such as Malaysia, Thailand, and Indonesia account for 91 percent of the R1E resources of tin and for 61 percent of resources in other categories. The United States has less than 0.05 percent of the world's tin R1E in major deposits. Available data suggest that the Soviet Union may have about 4 percent of resources in this category. The industrial market economy countries of the United States, Japan, Federal Republic of Germany, and the United Kingdom are major consumers of tin, whereas the major tin-producing countries generally consume little tin. The Soviet Union and China are both major producers and consumers of tin. At the end of World War II, the four largest tin-producing countries (Bolivia, the Belgian Congo (Zaire), Nigeria, and Malaysia) produced over 80 percent of the world's tin. In 1986, the portion of production from the four largest producers (Malaysia, Brazil, Soviet Union, Indonesia) declined to about 55 percent, while the price of tin rose from about $1,500 to $18,000 per metric ton. In response to tin shortages during World War II, the United States began stockpiling refined tin metal from approximately 1946 to 1953 to ensure a strategic supply in the event of another war. Since World War II, there have been six International Tin Agreements to maintain price and supply stability between tin producers and consumers. Artificially high prices set by the tin-producing members and a tin glut brought on by independent producers like Brazil caused the collapse of the world tin market in late 1985; the International Tin Council exhausted its credit to support the market price. By the year 2025, Bolivia's underground lode mines will likely have insignificant production, as will those in the United Kingdom. Tin mines in the Southeast Asian Tin Belt will still be active. Brazil, which has risen from the eighth-ranked tin-producing country in 1982 to the largest producer in 1988, will likely be a major influence on world tin production well into the 21st century. The future mining activity of deposits presently inactive in Australia is impossible to predict.

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

Comparative assessment of gastrointestinal irritant potency in man of tin(II) chloride and tin migrated from packaging.

PubMed

Boogaard, Peter J; Boisset, Michel; Blunden, Steve; Davies, Scot; Ong, Teng Jin; Taverne, Jean-Pierre

2003-12-01

Tin is present in low concentrations in most canned foods and beverages, the highest levels being found in products packaged in unlacquered or partially lacquered tinplate cans. A limited number of case-reports of acute gastrointestinal disorders after consumption of food containing 100-500 mg/kg tin have been reported, but these reports suffer many insufficiencies. Controlled clinical studies on acute effects of tin migrated from packaging suggest a threshold concentration for adverse effects (AEs) of >730 mg/kg. Two separate randomised, single-centre, double-blind, crossover studies, enabling comparison of the tolerability of tin added as tin(II) chloride at concentrations of <0.5, 161, 264 and 529 mg/kg in 250 ml tomato juice in 20 volunteers (Study 1) and tin migrated from packaging at concentrations of <0.5, 201 and 267 mg/kg in 250 ml tomato soup in 24 volunteers (Study 2) were carried out. Distribution studies were conducted to get insight in the acute AEs of low molecular weight (<1000 Da) tin species in the soluble fraction of food products. Results show that the chemical form of tin and not the elemental concentration per se determines the severity of AEs. A clear dose-response relationship was only observed when tin was added as tin(II) chloride in tomato juice. No clinically significant AEs were reported in Study 2 and comparison of the incidence of tin-related AEs showed no difference between the dose levels (including control). Tin species of low molecular weight in supernatant represented 31-32% of total tin in canned tomato soup versus 56-61% in juice freshly spiked with tin(II) chloride. Differences in the incidence of AEs following administration of tomato juice with 161 and 264 mg of tin per kg and tomato soup with 201 and 267 mg of tin per kg likely results from differences in the concentration of low molecular weight tin species and in the nature of tin complexes formed. The results of this work demonstrate that tin levels up to 267 mg/kg in canned food cause no AEs in healthy adults and support the currently proposed tin levels of 200 mg/kg and 250 mg/kg for canned beverages and canned foods, respectively, as safe levels for adults in the general population.

Telomere dysfunction and cell survival: roles for distinctTIN2-containing complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sahn-Ho; Davalos, Albert R.; Heo, Seok-Jin

Telomeres are maintained by three DNA binding proteins, TRF1, TRF2 and POT1, and several associated factors. One factor, TIN2, binds TRF1 and TRF2 directly and POT1 indirectly. These and two other proteins form a soluble complex that may be the core telomere-maintenance complex. It is not clear whether subcomplexes exist or function in vivo. Here, we provide evidence for two TIN2 subcomplexes with distinct functions in human cells. TIN2 ablation by RNA interference caused telomere uncapping and p53-independent cell death in all cells tested. However, we isolated two TIN2 complexes from cell lysates, each selectively sensitive to a TIN2 mutantmore » (TIN2-13, TIN2-15C). In cells with wild-type p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere uncapping and eventual growth arrest. In cells lacking p53 function, TIN215C more than TIN2-13 caused genomic instability and cell death. Thus, TIN2 subcomplexes likely have distinct functions in telomere maintenance, and may provide selective targets for eliminating cells with mutant p53.« less

Sodium Hydroxide and Calcium Hydroxide Hybrid Oxygen Bleaching with System

NASA Astrophysics Data System (ADS)

Doelle, K.; Bajrami, B.

2018-01-01

This study investigates the replacement of sodium hydroxide in the oxygen bleaching stage using a hybrid system consisting of sodium hydroxide calcium hydroxide. Commercial Kraft pulping was studied using yellow pine Kraft pulp obtained from a company in the US. The impact of sodium hydroxide, calcium hydroxide hybrid system in regard to concentration, reaction time and temperature for Kraft pulp was evaluated. The sodium hydroxide and calcium hydroxide dosage was varied between 0% and 15% based on oven dry fiber content. The bleaching reaction time was varied between 0 and 180 minutes whereas the bleaching temperature ranged between 70 °C and 110 °C. The ability to bleach pulp was measured by determining the Kappa number. Optimum bleaching results for the hybrid system were achieved with 4% sodium hydroxide and 2% calcium hydroxide content. Beyond this, the ability to bleach pulp decreased.

Contribution to the knowledge of nickel hydroxide electrodes. 5. Analysis and electrochemical behavior of cadmium nickel hydroxides

NASA Technical Reports Server (NTRS)

Bode, H.; Dennstedt, W.

1981-01-01

Electrochemical experiments performed at sintered and bulk electrodes show that beta nickel hydroxide contains an electrochemically inactive proportion of cadmium hydroxide of up to 10%. The electrochemically ineffective cadmium hydroxide is homogeneously dissolved in beta nickel hydroxide.

Tin

USGS Publications Warehouse

Kamilli, Robert J.; Kimball, Bryn E.; Carlin, James F.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Tin (Sn) is one of the first metals to be used by humans. Almost without exception, tin is used as an alloy. Because of its hardening effect on copper, tin was used in bronze implements as early as 3500 B.C. The major uses of tin today are for cans and containers, construction materials, transportation materials, and solder. The predominant ore mineral of tin, by far, is cassiterite (SnO2).In 2015, the world’s total estimated mine production of tin was 289,000 metric tons of contained tin. Total world reserves at the end of 2016 were estimated to be 4,700,000 metric tons. China held about 24 percent of the world’s tin reserves and accounted for 38 percent of the world’s 2015 production of tin.The proportion of scrap used in tin production is between 10 and 25 percent. Unlike many metals, tin recycling is relatively efficient, and the fraction of tin in discarded products that get recycled is greater than 50 percent.Only about 20 percent of the world’s identified tin resources occur as primary hydrothermal hard-rock veins, or lodes. These lodes contain predominantly high-temperature minerals and almost invariably occur in close association with silicic, peraluminous granites. About 80 percent of the world’s identified tin resources occur as unconsolidated secondary or placer deposits in riverbeds and valleys or on the sea floor. The largest concentration of both onshore and offshore placers is in the extensive tin belt of Southeast Asia, which stretches from China in the north, through Thailand, Burma (also referred to as Myanmar), and Malaysia, to the islands of Indonesia in the south. Furthermore, tin placers are almost always found closely allied to the granites from which they originate. Other countries with significant tin resources are Australia, Bolivia, and Brazil.Most hydrothermal tin deposits belong to what can be thought of as a superclass of porphyry-greisen deposits. The hydrothermal tin deposits are all characterized by a close spatial, temporal, and genetic association with highly differentiated, peraluminous porphyritic granite intrusions. The intrusions form pegmatites; disseminated ore; parallel or subparallel, greisen-bordered sheeted veins that either cross-cut the intrusion or are peripheral to it; skarns; and (or) limestone replacements that contain different amounts of cassiterite, molybdenite, and wolframite.The tectonic settings of tin-bearing granites are relatively well understood and of limited variety. Tin and tungsten deposits and their associated igneous rocks are found mainly in continental settings.Historically, prospecting for tin has been carried out by the time-honored methods of panning, drilling, trenching, and assaying. Geophysical and geochemical surveys have been employed to cover large areas more rapidly, isolating areas of possible tin deposits so that drilling can be more effective and less costly. Elemental concentrations and relationships of the lithophile elements, especially barium, lithium, niobium, potassium, rubidium, and zirconium, are the most reliable chemical indicators of ore-forming processes and tin-bearing potential.The average human diet includes an intake of about 10 milligrams per day of tin. Ingestion of tin in significantly greater amounts than 10 milligrams per day may lead to a stomach ache, anemia, and liver and kidney problems. Exposure to some organo-tin compounds can interfere with brain and nervous system function and, in severe cases, can cause death. Extended inhalation of tin oxide—an issue mainly for those people who work in the tin industry—results in a higher potential to develop stannosis, which is a mild disease of the lungs caused by the inhalation of tin-bearing dust. Inorganic tin is poorly absorbed by the body, and no evidence exists for the carcinogenicity of metallic tin and tin compounds in humans.Most placer tin deposits are mined by open pit and (or) dredging methods. Mining of alluvial placers in modern streambeds and riverbeds is likely to increase the amount of sediment delivered downstream. This, combined with potential diversion of rivers and streams, may negatively affect downstream ecosystems. Many of the placer deposits located in Burma, Indonesia, Malaysia, and Thailand are located offshore. Most offshore placer tin deposits are mined by dredging methods, which have the potential to negatively affect benthic, midwater, and pelagic ecosystems.In a congressionally mandated U.S. Department of Defense study of strategic minerals published in 2013, tin has the greatest shortfall amount (insufficient supply to meet demand) at \\$416 million; this amount is more than twice that of antimony ($182 million), which is the strategic mineral with the next largest shortfall amount (U.S. Department of Defense, 2013). The United States imported 75 percent of its tin supply in 2015. During the period 2012–15, these imports were from, in descending order of amount imported, Peru, Indonesia, Malaysia, and Bolivia.A promising advancement concerning research into the origin of tin deposits is the recent development of a reliable method of analyzing tin isotopes in cassiterite. Although the mechanism of transport and deposition of tin is fairly well understood, the means by which tin is incorporated into the parent magma at the points of magma generation and ascent needs further investigation.Tin metallogenic provinces worldwide are well known. Consequently, any undiscovered tin deposits will likely be spatially close to known deposits or extensions of the same.

Hollow tin/chromium whiskers

NASA Astrophysics Data System (ADS)

Cheng, Jing; Vianco, Paul T.; Li, James C. M.

2010-05-01

Tin whiskers have been an engineering challenge for over five decades. The mechanism has not been agreed upon thus far. This experiment aimed to identify a mechanism by applying compressive stresses to a tin film evaporated on silicon substrate with an adhesion layer of chromium in between. A phenomenon was observed in which hollow whiskers grew inside depleted areas. Using focused ion beam, the hollow whiskers were found to contain both tin and chromium. At the bottom of the depleted areas, thin tin/tin oxide film remained over the chromium layer. It indicates that tin transport occurred along the interface between tin and chromium layers.

Peroxide induced tin oxide coating of graphene oxide at room temperature and its application for lithium ion batteries.

PubMed

Sladkevich, S; Gun, J; Prikhodchenko, P V; Gutkin, V; Mikhaylov, A A; Novotortsev, V M; Zhu, J X; Yang, D; Hng, H H; Tay, Y Y; Tsakadze, Z; Lev, O

2012-12-07

We describe a new, simple and low-temperature method for ultra-thin coating of graphene oxide (GO) by peroxostannate, tin oxide or a mixture of tin and tin oxide crystallites by different treatments. The technique is environmentally friendly and does not require complicated infrastructure, an autoclave or a microwave. The supported peroxostannate phase is partially converted after drying to crystalline tin oxide with average, 2.5 nm cassiterite crystals. Mild heat treatment yielded full coverage of the reduced graphene oxide by crystalline tin oxide. Extensive heat treatment in vacuum at >500 °C yielded a mixture of elemental tin and cassiterite tin oxide nanoparticles supported on reduced graphene oxide (rGO). The usefulness of the new approach was demonstrated by the preparation of two types of lithium ion anodes: tin oxide-rGO and a mixture of tin oxide and tin coated rGO composites (SnO(2)-Sn-rGO). The electrodes exhibited stable charge/discharge cyclability and high charging capacity due to the intimate contact between the conductive graphene and the very small tin oxide crystallites. The charging/discharging capacity of the anodes exceeded the theoretical capacity predicted based on tin lithiation. The tin oxide coated rGO exhibited higher charging capacity but somewhat lower stability upon extended charge/discharge cycling compared to SnO(2)-Sn-rGO.

Telomere dysfunction and cell survival: Roles for distinct TIN2-containing complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sahn-ho; Davalos, Albert R.; Heo, Seok-Jin

Telomeres are maintained by three DNA binding proteins (TRF1, TRF2 and POT1), and several associated factors. One factor, TIN2, binds TRF1 and TRF2 directly and POT1 indirectly. Along with two other proteins, TPP1 and hRap1, these form a soluble complex that may be the core telomere maintenance complex. It is not clear whether sub-complexes also exist in vivo. We provide evidence for two TIN2 sub-complexes with distinct functions in human cells. We isolated these two TIN2 sub-complexes from nuclear lysates of unperturbed cells and cells expressing TIN2 mutants TIN2-13, TIN2-15C, which cannot bind TRF2 or TRF1, respectively. In cells withmore » wild-type p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere uncapping and eventual growth arrest. In cells lacking p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere dysfunction and cell death. Our findings suggest that distinct TIN2 complexes exist, and that TIN2-15C-sensitive subcomplexes are particularly important for cell survival in the absence of functional p53.« less

SEPARATION OF PLUTONIUM HYDROXIDE FROM BISMUTH HYDROXIDE

DOEpatents

Watt, G.W.

1958-08-19

An tmproved method is described for separating plutonium hydroxide from bismuth hydroxide. The end product of the bismuth phosphate processes for the separation amd concentration of plutonium is a inixture of bismuth hydroxide amd plutonium hydroxide. It has been found that these compounds can be advantageously separated by treatment with a reducing agent having a potential sufficient to reduce bismuth hydroxide to metalltc bisinuth but not sufficient to reduce the plutonium present. The resulting mixture of metallic bismuth and plutonium hydroxide can then be separated by treatment with a material which will dissolve plutonium hydroxide but not metallic bismuth. Sodiunn stannite is mentioned as a preferred reducing agent, and dilute nitric acid may be used as the separatory solvent.

Strategies to Reduce Tin and Other Metals in Electronic Cigarette Aerosol

PubMed Central

Williams, Monique; To, An; Bozhilov, Krassimir; Talbot, Prue

2015-01-01

Background Metals are present in electronic cigarette (EC) fluid and aerosol and may present health risks to users. Objective The objective of this study was to measure the amounts of tin, copper, zinc, silver, nickel and chromium in the aerosol from four brands of EC and to identify the sources of these metals by examining the elemental composition of the atomizer components. Methods Four brands of popular EC were dissected and the cartomizers were examined microscopically. Elemental composition of cartomizer components was determined using integrated energy dispersive X-ray microanalysis, and the concentrations of the tin, copper, zinc silver, nickel, and chromium in the aerosol were determined for each brand using inductively coupled plasma optical emission spectroscopy. Results All filaments were made of nickel and chromium. Thick wires were copper coated with either tin or silver. Wires were joined to each other by tin solder, brazing, or by brass clamps. High concentrations of tin were detected in the aerosol when tin solder joints were friable. Tin coating on copper wires also contributed to tin in the aerosol. Conclusions Tin concentrations in EC aerosols varied both within and between brands. Tin in aerosol was reduced by coating the thick wire with silver rather than tin, placing stable tin solder joints outside the atomizing chamber, joining wires with brass clamps or by brazing rather than soldering wires. These data demonstrate the feasibility of removing tin and other unwanted metals from EC aerosol by altering designs and using materials of suitable quality. PMID:26406602

METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

DOEpatents

Lemon, L.C.

1960-05-24

Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

Raman Scattering from Tin

DTIC Science & Technology

2015-09-01

ARL-TR-7448 ● SEP 2015 US Army Research Laboratory Raman Scattering from Tin by Patrick A Folkes, Patrick Taylor, Charles Rong...REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Raman Scattering from Tin 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c... tin as an analytical tool for discerning specific allotropic differences in ultra-thin tin films, and discerning differences between the tin and the

Electrochemical mechanism of tin membrane electrodeposition under ultrasonic waves.

PubMed

Nan, Tianxiang; Yang, Jianguang; Chen, Bing

2018-04-01

Tin was electrodeposited from chloride solutions using a membrane cell under ultrasonic waves. Cyclic voltammetry (CV), linear sweep voltammetry (LSV), chronoamperometry (CHR), and chronopotentiometry were applied to investigate the electrochemical mechanism of tin electrodeposition under ultrasonic field. Chronoamperometry curves showed that the initial process of tin electrodeposition followed the diffusion controlled three-dimensional nucleation and grain growth mechanism. The analysis of the cyclic voltammetry and linear sweep voltammetry diagrams showed that the application of ultrasound can change the tin membrane electro-deposition reaction from diffusion to electrochemical control, and the optimum parameters for tin electrodeposition were H + concentration 3.5 mol·L -1 , temperature 35 °C and ultrasonic power 100 W. The coupling ultrasonic field played a role in refining the grain in this process. The growth of tin crystals showed no orientation preferential, and the tin deposition showed a tendency to form a regular network structure after ultrasonic coupling. While in the absence of ultrasonic coupling, the growth of tin crystals has a high preferential orientation, and the tin deposition showed a tendency to form tin whiskers. Ultrasonic coupling was more favorable for obtaining a more compact and smoother cathode tin layer. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of adhesions of amorphous Fe and Al hydroxides on surface charge and adsorption of K+ and Cd2+ on rice roots.

PubMed

Liu, Zhao-Dong; Wang, Hai-Cui; Zhou, Qin; Xu, Ren-Kou

2017-11-01

Iron (Fe) and aluminum (Al) hydroxides in variable charge soils attached to rice roots may affect surface-charge properties and subsequently the adsorption and uptake of nutrients and toxic metals by the roots. Adhesion of amorphous Fe and Al hydroxides onto rice roots and their effects on zeta potential of roots and adsorption of potassium (K + ) and cadmium (Cd 2+ ) by roots were investigated. Rice roots adsorbed more Al hydroxide than Fe hydroxide because of the greater positive charge on Al hydroxide. Adhesion of Fe and Al hydroxides decreased the negative charge on rice roots, and a greater effect of the Al hydroxide. Consequently, adhesion of Fe and Al hydroxides reduced the K + and Cd 2+ adsorption by rice roots. The results of attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and desorption of K + and Cd 2+ from rice roots indicated that physical masking by Fe and Al hydroxides and diffuse-layer overlapping between the positively-charged hydroxides and negatively-charged roots were responsible for the reduction of negative charge on roots induced by adhesion of the hydroxides. Therefore, the interaction between Fe and Al hydroxides and rice roots reduced negative charge on roots and thus inhibited their adsorption of nutrient and toxic cations. Copyright © 2017 Elsevier Inc. All rights reserved.

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

78 FR 16048 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-13

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services registration TIN matching--application and screens for TIN matching interactive. DATES: Written comments should be received...

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

75 FR 5854 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services Registration TIN Matching--Application and Screens for TIN Matching Interactive. DATES: Written comments should be received...

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

Epigenetic lead, zinc, silver, antimony, tin, and gold veins in Boulder Basin, Blaine and Custer counties, Idaho; potential for economic tin mineralization

USGS Publications Warehouse

Ratchford, Michael E.

2002-01-01

Boulder Basin is in a northwest-trending belt of allochthonous Paleozoic rocks in the Boulder Mountains of central Idaho. Regional Tertiary extension resulted in widespread normal faulting and coeval emplacement of shallow-level intrusions and extrusive rocks of the Challis Volcanic Group. Epigenetic lead-zinc-silver-antimony-tin-gold vein deposits formed during Tertiary extension and are hosted within Paleozoic strata. The major orebodies are in the lower plate of the Boulder Basin thrust fault, in massive quartzite of the Middle Pennsylvanian to Lower Permian Wood River Formation. Anomalous concentrations of tin are present in the base-metal mineral assemblage of the Boulder Basin ore deposits. The tin-bearing veins in Boulder Basin are strikingly similar to Bolivian tin deposits. The deposit model for Bolivian tin deposits identifies buried tin porphyry below the tin-bearing vein system.

Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

NASA Technical Reports Server (NTRS)

Dennstedt, W.; Loeser, W.

1982-01-01

Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

21 CFR 184.1631 - Potassium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Potassium hydroxide. 184.1631 Section 184.1631... Listing of Specific Substances Affirmed as GRAS § 184.1631 Potassium hydroxide. (a) Potassium hydroxide..., including pellets, flakes, sticks, lumps, and powders. Potassium hydroxide is obtained commercially from the...

21 CFR 184.1631 - Potassium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Potassium hydroxide. 184.1631 Section 184.1631... Listing of Specific Substances Affirmed as GRAS § 184.1631 Potassium hydroxide. (a) Potassium hydroxide..., including pellets, flakes, sticks, lumps, and powders. Potassium hydroxide is obtained commercially from the...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2014 CFR

2014-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2013 CFR

2013-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

78 FR 39644 - Information Reporting for Affordable Insurance Exchanges

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-02

... Exchange-- (i) The name, address, and taxpayer identification number (TIN), or date of birth if a TIN is... advance credit payments (taxpayer), and the name and TIN of the individual's spouse, if applicable; (ii) The name, address, and TIN, or date of birth if a TIN is not available, of an adult enrolling in...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

The prognostic value of tumor-infiltrating neutrophils in gastric adenocarcinoma after resection.

PubMed

Zhao, Jing-jing; Pan, Ke; Wang, Wei; Chen, Ju-gao; Wu, Yan-heng; Lv, Lin; Li, Jian-jun; Chen, Yi-bing; Wang, Dan-dan; Pan, Qiu-zhong; Li, Xiao-dong; Xia, Jian-chuan

2012-01-01

Several pieces of evidence indicate that tumor-infiltrating neutrophils (TINs) are correlated to tumor progression. In the current study, we explore the relationship between TINs and clinicopathological features of gastric adenocarcinoma patients. Furthermore, we investigated the prognostic value of TINs. The study was comprised of two groups, training group (115 patients) and test group (97 patients). Biomarkers (intratumoral CD15+ neutrophils) were assessed by immunohistochemistry. The relationship between clinicopathological features and patient outcome were evaluated using Cox regression and Kaplan-Meier analysis. Immunohistochemical detection showed that the tumor-infiltrating neutrophils (TINs) in the training group ranged from 0.00-115.70 cells/high-power microscopic field (HPF) and the median number was 21.60 cells/HPF. Based on the median number, the patients were divided into high and low TINs groups. Chi-square test analysis revealed that the density of CD15+ TINs was positively associated with lymph node metastasis (p = 0.024), distance metastasis (p = 0.004) and UICC (International Union Against Cancer) staging (p = 0.028). Kaplan-Meier analysis showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.002). Multivariate Cox's analysis showed that the density of CD15+ TINs was an independent prognostic factor for overall survival of gastric adenocarcinoma patients. Using another 97 patients as a test group and basing on the median number of TINs (21.60 cells/HPF) coming from the training group, Kaplan-Meier analysis also showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.032). The results verify that the number of CD15+ TINs can predict the survival of gastric adenocarcinoma surgical patients. The presence of CD15+ TINs is an independent and unfavorable factor in the prognosis of gastric adenocarcinoma patients. Targeting CD15+ TINs may be a potential intervenient therapy in the future.

21 CFR 184.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... is prepared as a white precipitate by the addition of sodium hydroxide to a water soluble magnesium... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Magnesium hydroxide. 184.1428 Section 184.1428... Listing of Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide...

21 CFR 184.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... is prepared as a white precipitate by the addition of sodium hydroxide to a water soluble magnesium... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Magnesium hydroxide. 184.1428 Section 184.1428... Listing of Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide...

21 CFR 184.1631 - Potassium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Potassium hydroxide. 184.1631 Section 184.1631... GRAS § 184.1631 Potassium hydroxide. (a) Potassium hydroxide (KOH, CAS Reg. No. 1310-58-3) is also... powders. Potassium hydroxide is obtained commercially from the electrolysis of potassium chloride solution...

Evaluation of the suitability of tin slag in cementitious materials: Mechanical properties and Leaching behaviour

NASA Astrophysics Data System (ADS)

Rustandi, Andi; Wafa' Nawawi, Fuad; Pratesa, Yudha; Cahyadi, Agung

2018-01-01

Tin slag, a by-product of tin production has been used in cementitious application. The present investigation focuses on the suitability of tin slag as primary component in cement and as component that substitute some amount of Portland Cement. The tin slags studied were taken from Bangka, Indonesia. The main contents of the tin slag are SiO2, Al2O3, and Fe2O3 according to the XRF investigation. The aim of this article was to study the mechanical behaviour (compressive strength), microstructure and leaching behaviour of tin slag blended cement. This study used air-cooled tin slag that had been passed through 400# sieve to replace Portland Cement with ratio 0, 10, 20, 30, 40 by weight. Cement pastes and tin slag blended cement pastes were prepared by using water/cement ratio (W/C) of 0.40 by weight and hydrated for various curing ages of 3, 7, 14 days The microstructure of the raw tin slag was investigated using Scanning Electron Microscope (SEM). The phase composition of each cement paste was investigated using X-ray Diffraction (XRD). The aim of the leachability test was to investigate the environmental impacts of tin slag blended cement product in the range 4-8 pH by using static pH-dependent leaching test. The result show that the increase of the tin slag content decreasing the mortar compressive strength at early ages. The use of tin slag in cement provide economic benefits for all related industries.

Electronic and Optical Properties of Titanium Nitride Bulk and Surfaces from First Principles Calculations (Postprint)

DTIC Science & Technology

2015-11-18

thickness of the film, or substrate. In this work, we report calculations for titanium nitride ( TiN ), a promising material for plasmonic applications...stoichiometric bulk TiN , as well as of the TiN (100), TiN (110), and TiN (111) outermost surfaces. Density functional theory (DFT) and many-body GW methods...and the band structure for bulk TiN were shown to be consistent with previous work. Calculated dielectric functions, plasma frequencies, reflectivity

76 FR 38129 - Applications for New Awards; Americans With Disabilities Act (ADA) National Network Knowledge...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-29

...) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with the... number and TIN on your application; and d. Maintain an active CCR registration with current information... a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

77 FR 40596 - Applications for New Awards: Disability and Rehabilitation Research Projects and Centers Program...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

...) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with the... number and TIN on your application; and d. Maintain an active CCR registration with current information... a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

Thermochemical Concrete Pavement Scaling Mechanism: Navy F/A-18 Jet Aircraft Parking Apron Problem

DTIC Science & Technology

1998-06-01

boiling and recondensation) in hot, concentrated potassium hydroxide (E): Eqn 11 Alkaline Hydrolysis of Esters with Potassium Hydroxide KOH...RC02R’ -> KC02R + R’OH potassium alkyl ester (B) potassium ethanol(L) hydroxide (E) carboxylate (F) The overall reaction appears to make sense...carbonate (H) water 2. The parallel between calcium hydroxide and potassium hydroxide is not very accurate. Potassium hydroxide is a much stronger alkali

The Southeast Asian Tin Belt

NASA Astrophysics Data System (ADS)

Schwartz, M. O.; Rajah, S. S.; Askury, A. K.; Putthapiban, P.; Djaswadi, S.

1995-07-01

The Southeast Asian Tin Belt is a north-south elongate zone 2800 km long and 400 km wide, extending from Burma (Myanmar) and Thailand to Peninsular Malaysia and the Indonesian Tin Islands. Altogether 9.6 million tonnes of tin, equivalent to 54% of the world's tin production is derived from this region. Most of the granitoids in the region can be grouped geographically into elongate provinces or belts, based on petrographic and geochronological features. - The Main Range Granitoid Province in western Peninsular Malaysia, southern Peninsular Thailand and central Thailand is almost entirely made up of biotite granite (184-230 Ma). Tin deposits associated with these granites contributed 55% of the historic tin production of Southeast Asia. - The Northern Granitoid Province in northern Thailand (0.1% of tin production) also has dominant biotite granite (200-269 Ma) but it is distinguished by abundant post-intrusion deformation. - The Eastern Granitoid Province extends from eastern Peninsular Malaysia to eastern Thailand. The Malaysian part is subdivided into the East Coast Belt (220-263 Ma), Boundary Range Belt (197-257 Ma) and Central Belt (79-219 Ma). The granitoids cover a wide compositional range from biotite granite to hornblende-biotite granite/granodiorite and diorite-gabbro. Tin deposits are associated with biotite granite in the East Coast Belt (3% of tin production). The granitoids in the other areas of the Eastern Granitoid Province are barren. - The Western Granitoid Province (22-149 Ma) in northern Peninsular Thailand, western Thailand and Burma has biotite granite and hornblende-biotite granite/granodiorite. Tin deposits are associated with biotite granite, which probably is the dominant phase (14% of tin production). The granitoids of the Indonesian Tin Islands (193-251 Ma) do not permit grouping into geographically distinct units. Main Range-type and Eastern Province-type plutons occur next to each other. Most of the tin deposits are associated with Main Range-type plutons (28% of tin production). Tin-mineralized plutons are characterized by high concentrations of SiO 2, K 2O, Rb, Sn, Th and U, whereas the concentrations of Fe 2O 3, MgO, CaO, Na 2O, Ba and Sr as well as the Fe2O3/FeO ratios are low. Tin-mineralized plutons are also distinguished by high initial 87Sr/86Sr ratios low magnetic susceptibilities.

21 CFR 184.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... addition of sodium hydroxide to a water soluble magnesium salt or by hydration of reactive grades of... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Magnesium hydroxide. 184.1428 Section 184.1428... GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide (Mg(OH)2, CAS Reg. No. 1309-42-8) occurs...

In-plane conductance of thin films as a probe of surface chemical environment: Adsorbate effects on film electronic properties of indium tin oxide and gold

NASA Astrophysics Data System (ADS)

Swint, Amy Lynn

Changes in the in-plane conductance of conductive thin films are observed as a result of chemical adsorption at the surface. Reaction of the indium tin oxide (ITO) surface with Bronsted acids (bases) leads to increases (decreases) in its in-plane conductance as measured by a four-point probe configuration. The conductance varies monotonically with pH suggesting that the degree of surface protonation or hydroxylation controls the surface charge density, which in turn affects the width of the n-type depletion layer, and ultimately the in-plane conductance. Measurements at constant pH with a series of tetraalkylammonium hydroxide species of varying cation size indicate that surface dipoles also affect ITO conductance by modulating the magnitude of the surface polarization. Modulating the double layer with varying aqueous salt solutions also affects ITO conductance, though not to the same degree as strong Bronsted acids and bases. Solvents of varying dielectric constant and proton donating ability (ethanol, dimethylformamide) decrease ITO conductance relative to H2O. In addition, changing solvent gives rise to thermally-derived conductance transients, which result from exothermic solvent mixing. The self-assembly of alkanethiols at the surface increases the conductance of ITO films, most likely through carrier population effects. In all cases examined the combined effects of surface charge, adsorbed dipole layer magnitude and carrier injection are responsible for altering the ITO conductance. Besides being directly applicable to the control of electronic properties, these results also point to the use of four-point probe resistance measurements in condensed phase sensing applications. Ultrasensitive conductance-based gas phase sensing of organothiol adsorption to gold nanowires is accomplished with a limit of detection in the 105 molecule range. Further refinement of the inherently low noise resistance measurement may lead to observation of single adsorption events at the gold surface.

Spray pyrolysis deposition and photoelectrochemical properties of n-type BiOI nanoplatelet thin films.

PubMed

Hahn, Nathan T; Hoang, Son; Self, Jeffrey L; Mullins, C Buddie

2012-09-25

Bismuth oxy-iodide is a potentially interesting visible-light-active photocatalyst; yet there is little research regarding its photoelectrochemical properties. Herein we report the synthesis of BiOI nanoplatelet photoelectrodes by spray pyrolysis on fluorine-doped tin oxide substrates at various temperatures. The films exhibited n-type conductivity, most likely due to the presence of anion vacancies, and optimized films possessed incident photon conversion efficiencies of over 20% in the visible range for the oxidation of I(-) to I(3)(-) at 0.4 V vs Ag/AgCl in acetonitrile. Visible-light photons (λ > 420 nm) contributed approximately 75% of the overall photocurrent under AM1.5G illumination, illustrating their usefulness under solar light illumination. A deposition temperature of 260 °C was found to result in the best performance due to the balance of morphology, crystallinity, impurity levels, and optical absorption, leading to photocurrents of roughly 0.9 mA/cm(2) at 0.4 V vs Ag/AgCl. Although the films performed stably in acetonitrile, their performance decreased significantly upon extended exposure to water, which was apparently caused by a loss of surface iodine and subsequent formation of an insulating bismuth hydroxide layer.

Chemical Functionalization, Self-Assembly, and Applications of Nanomaterials and Nanocomposites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiao, Tifeng; Yan, Xingbin; Balan, Lavinia

2014-01-01

This special issue addresses the research studies on chemical functionalization, self-assembly, and applications of nanomaterials and nanocomposites. It contains twentyfour articles including two reviews and twenty-two research articles. It is used to create new functional nanomaterials and nanocomposites with a variety of sizes and morphologies such as Zn/Al layered double hydroxide, tin oxide nanowires, FeOOH-modified anion resin, Au nanoclusters silica composite nanospheres, Ti-doped ZnO sol-composite films, TiO2/ZnO composite, graphene oxide nanocomposites, LiFePO4/C nanocomposites, and chitosan nanoparticles. These nanomaterials and nanocomposites have widespread applications in tissue engineering, antitumor, sensors, photoluminescence, electrochemical, and catalytic properties. In addition, this themed issue includes somemore » research articles about self-assembly systems covering organogels and Langmuir films. Furthermore, B. Blasiak et al. performed a literature survey on the recent advances in production, functionalization, toxicity reduction, and application of nanoparticles in cancer diagnosis, treatment, and treatment monitoring. P. Colson et al. performed a literature survey on the recent advances in nanosphere lithography due to its compatibility with wafer-scale processes as well as its potential to manufacture a wide variety of homogeneous one-, two-, or three-dimensional nanostructures.« less

Mineral resource of the month: tin

USGS Publications Warehouse

Carlin, James F.

2011-01-01

Tin was one of the earliest-known metals. Because of its hardening effect on copper, tin was used in bronze implements as early as 3500 B.C. Bronze, a copper-tin alloy that can be sharpened and is hard enough to retain a cutting edge, was used during the Bronze Age in construction tools as well as weapons for hunting and war. The geographical separation between tin-producing and tin-consuming nations greatly influenced the patterns of early trade routes. Historians think that as early as 1500 B.C., Phoenicians traveled by sea to the Cornwall district of England to obtain tin. The pure metal was not used unalloyed until about 600 B.C.

Tin recycling in the United States in 1998

USGS Publications Warehouse

Carlin, James F.

2001-01-01

This materials flow study includes a description of tin supply and demand factors for the United States to illustrate the extent of tin recycling and to identify recycling trends. Understanding the flow of materials from source to ultimate disposition can assist in improving the management of the use of natural resources in a manner that is compatible with sound environmental practices. The quantity of tin recycled in 1998 as a percentage of apparent tin supply was estimated to be about 22%, and recycling efficiency was estimated to be 75%. Of the total tin consumed in products for the U.S. market in 1998, an estimated 12% was consumed in products where the tin was not recyclable (dissipative uses).

Dissolution mechanism of aluminum hydroxides in acid media

NASA Astrophysics Data System (ADS)

Lainer, Yu. A.; Gorichev, I. G.; Tuzhilin, A. S.; Gololobova, E. G.

2008-08-01

The effects of the concentration, temperature, and potential at the hydroxide/electrolyte interface on the aluminum hydroxide dissolution in sulfuric, hydrochloric, and perchloric acids are studied. The limiting stage of the aluminum hydroxide dissolution in the acids is found to be the transition of the complexes that form on the aluminum hydroxide surface from the solid phase into the solution. The results of the calculation of the acid-base equilibrium constants at the oxide (hydroxide)/solution interface using the experimental data on the potentiometric titration of Al2O3 and AlOOH suspensions are analyzed. A mechanism is proposed for the dissolution of aluminum hydroxides in acid media.

76 FR 28426 - Applications for New Awards; Assistive Technology Act of 1998, as Amended (AT Act)-National...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-17

... (DUNS) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with... DUNS number and TIN on your application; and d. Maintain an active CCR registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

78 FR 42937 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-18

... Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

77 FR 11190 - Yokohama Tire Company, Denial of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-24

... (TIN)/partial TIN required by paragraph S5.5.1 on one of the tire sidewalls. YTC indicates that the noncompliant tires do however include the full TIN on the intended outboard sidewall. YTC argues that the TIN and the partial TIN are used to properly identify tires that are involved in a safety campaign. YTC...

26 CFR 31.3406(g)-1 - Exception for payments to certain payees and certain other payments.

Code of Federal Regulations, 2013 CFR

2013-04-01

... payee's TIN and the payee's TIN has been validated through the IRS TIN Matching Program; or (B) The QPCA... not constitute notice by the IRS that the payee's TIN is incorrect for purposes of section 3406(a)(1....) At the time of enrollment, Q obtains Merchant X's taxpayer identification number (TIN). Merchant X is...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

78 FR 36755 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-19

... Identification Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

78 FR 38958 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-28

... Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

Reductive spectrophotometry of divalent tin sensitization on soda lime glass

NASA Astrophysics Data System (ADS)

Bejugam, Vinith; Wei, Xingfei; Roper, D. Keith

2016-07-01

Rapid and facile evaluation of tin (II) sensitization could lead to improved understanding of metal deposition in electroless (EL) plating. This report used a balanced redox reaction between 3,3‧,5,5‧-tetramethylbenzidine dihydrochloride (TMB-HCL) and N-bromosuccinimide (NBS) to evaluate effects of sensitization conditions (i.e., sensitization time, analyte concentration, aqueous immersion, and acid content) on the accumulated mass of surface-associated divalent tin ion. The accumulated mass of tin (II) increased as the sensitization time increased up to 30 s in proportion to aqueous tin (II) chloride concentrations between 2.6 and 26 mM at a trifluoroacetic acid (TFA) content of 68 mM. The average mass peaked at 7.3 nanomoles (nmol) per cm2 after a 5 s aqueous immersion post-sensitization, and then decreased with increasing aqueous immersion post-sensitization. The total average tin (II) + tin (IV) accumulated on soda lime glass measured by inductively coupled plasma optical emission spectrometry (ICP-OES) was 17% higher at 30 s sensitization, suggesting a fraction of the tin (II) present may have oxidized to tin (IV). These results indicated that in situ spectrophotometric evaluation of tin (II) could support development of EL plating for electronics, catalysis, and solar cells.

Synthesis of high capacity cathodes for lithium-ion batteries by morphology-tailored hydroxide co-precipitation

NASA Astrophysics Data System (ADS)

Wang, Dapeng; Belharouak, Ilias; Ortega, Luis H.; Zhang, Xiaofeng; Xu, Rui; Zhou, Dehua; Zhou, Guangwen; Amine, Khalil

2015-01-01

Nickel manganese hydroxide co-precipitation inside a continuous stirred tank reactor was studied with sodium hydroxide and ammonium hydroxide as the precipitation agents. The ammonium hydroxide concentration had an effect on the primary and secondary particle evolution. The two-step precipitation mechanism proposed earlier was experimentally confirmed. In cell tests, Li- and Mn-rich composite cathode materials based on the hydroxide precursors demonstrated good electrochemical performance in terms of cycle life over a wide range of lithium content.

Corrosion Behavior of Carbon Steel in Concrete Material Composed of Tin Slag Waste in Aqueous Chloride Solution

NASA Astrophysics Data System (ADS)

Rustandi, Andi; Cahyadi, Agung; Taruli Siallagan, Sonia; Wafa' Nawawi, Fuad; Pratesa, Yudha

2018-01-01

Tin slag is a byproduct of tin ore smelting process which is rarely utilized. The main purpose of this work is to investigate the use of tin slag for concrete cement material application compared to the industrial Ordinary Portland Cement (OPC). Tin slag composition was characterized by XRD and XRF analysis. The characterization results showed the similar chemical composition of tin slag and OPC. It also revealed the semi crystalline structure of tin slag sample. Several electrochemical tests were performed to evaluate corrosion behavior of tin slag, OPC and various mixed composition of both materials and the addition of CaO. The corrosion behavior of OPC and tin slag were evaluated by using Cyclic Polarization, Electrochemical Impedance Spectroscopy (EIS) and Electrochemical Frequency Modulation (EFM) methods. Aqueous sodium chloride (NaCl) solution with 3.5% w.t concentration which similar to seawater was used as the electrolyte in this work. The steel specimen used as the reinforce bar (rebar) material of the concrete was carbon steel AISI 1045. The rebar was embedded in the concrete cement which composed of OPC and the various composition of tin slag including slag without addition of CaO and slag mixed with addition of 50 % CaO. The electrochemical tests results revealed that tin slag affected its corrosion behavior which becoming more active and increasing the corrosion rate as well as decreasing the electrochemical impedance.

Low temperature processed complementary metal oxide semiconductor (CMOS) device by oxidation effect from capping layer.

PubMed

Wang, Zhenwei; Al-Jawhari, Hala A; Nayak, Pradipta K; Caraveo-Frescas, J A; Wei, Nini; Hedhili, M N; Alshareef, H N

2015-04-20

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190 °C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field.

Corrosion resistance and mechanical properties of titanium nitride plating on orthodontic wires.

PubMed

Sugisawa, Haruki; Kitaura, Hideki; Ueda, Kyosuke; Kimura, Keisuke; Ishida, Masahiko; Ochi, Yumiko; Kishikawa, Akiko; Ogawa, Saika; Takano-Yamamoto, Teruko

2018-03-30

Titanium nitride (TiN) coating by ion plating has properties such as high hardness, wear resistance, corrosion resistance, and surface lubricity, therefore TiN coating is often used in various dental appliances and materials. In this study, we evaluated the corrosion behaviors and mechanical properties of TiN coated stainless steel (SS) and nickel titanium (Ni-Ti) orthodontic wires prepared by ion plating. TiN coating by ion plating improves the corrosion resistance of orthodontic wires. The corrosion pitting of the TiN coated wire surface become small. The tensile strength and stiffness of SS wire were increased after TiN coating. In contrast, its elastic force, which is a property for Ni-Ti wire, was decreased. In addition, TiN coating provided small friction forces. The low level of friction may increase tooth movement efficiently. Therefore, TiN coated SS wire could be useful for orthodontics treatment.

Low Temperature Processed Complementary Metal Oxide Semiconductor (CMOS) Device by Oxidation Effect from Capping Layer

PubMed Central

Wang, Zhenwei; Al-Jawhari, Hala A.; Nayak, Pradipta K.; Caraveo-Frescas, J. A.; Wei, Nini; Hedhili, M. N.; Alshareef, H. N.

2015-01-01

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190°C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field. PMID:25892711

The Prognostic Value of Tumor-Infiltrating Neutrophils in Gastric Adenocarcinoma after Resection

PubMed Central

Wang, Wei; Chen, Ju-gao; Wu, Yan-heng; Lv, Lin; Li, Jian-jun; Chen, Yi-bing; Wang, Dan-dan; Pan, Qiu-zhong; Li, Xiao-dong; Xia, Jian-chuan

2012-01-01

Background Several pieces of evidence indicate that tumor-infiltrating neutrophils (TINs) are correlated to tumor progression. In the current study, we explore the relationship between TINs and clinicopathological features of gastric adenocarcinoma patients. Furthermore, we investigated the prognostic value of TINs. Patients and Methods The study was comprised of two groups, training group (115 patients) and test group (97 patients). Biomarkers (intratumoral CD15+ neutrophils) were assessed by immunohistochemistry. The relationship between clinicopathological features and patient outcome were evaluated using Cox regression and Kaplan-Meier analysis. Results Immunohistochemical detection showed that the tumor-infiltrating neutrophils (TINs) in the training group ranged from 0.00–115.70 cells/high-power microscopic field (HPF) and the median number was 21.60 cells/HPF. Based on the median number, the patients were divided into high and low TINs groups. Chi-square test analysis revealed that the density of CD15+ TINs was positively associated with lymph node metastasis (p = 0.024), distance metastasis (p = 0.004) and UICC (International Union Against Cancer) staging (p = 0.028). Kaplan-Meier analysis showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.002). Multivariate Cox's analysis showed that the density of CD15+ TINs was an independent prognostic factor for overall survival of gastric adenocarcinoma patients. Using another 97 patients as a test group and basing on the median number of TINs (21.60 cells/HPF) coming from the training group, Kaplan-Meier analysis also showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.032). The results verify that the number of CD15+ TINs can predict the survival of gastric adenocarcinoma surgical patients. Conclusions The presence of CD15+ TINs is an independent and unfavorable factor in the prognosis of gastric adenocarcinoma patients. Targeting CD15+ TINs may be a potential intervenient therapy in the future. PMID:22442706

Canopy architectural and physiological characterization of near-isogenic wheat lines differing in the tiller inhibition gene tin.

PubMed

Moeller, Carina; Evers, Jochem B; Rebetzke, Greg

2014-01-01

Tillering is a core constituent of plant architecture, and influences light interception to affect plant and crop performance. Near-isogenic lines (NILs) varying for a tiller inhibition (tin) gene and representing two genetic backgrounds were investigated for tillering dynamics, organ size distribution, leaf area, light interception, red: far-red ratio, and chlorophyll content. Tillering ceased earlier in the tin lines to reduce the frequencies of later primary and secondary tillers compared to the free-tillering NILs, and demonstrated the genetically lower tillering plasticity of tin-containing lines. The distribution of organ sizes along shoots varied between NILs contrasting for tin. Internode elongation commenced at a lower phytomer, and the peduncle was shorter in the tin lines. The flag leaves of tin lines were larger, and the longest leaf blades were observed at higher phytomers in the tin than in free-tillering lines. Total leaf area was reduced in tin lines, and non-tin lines invested more leaf area at mid-canopy height. The tiller economy (ratio of seed-bearing shoots to numbers of shoots produced) was 10% greater in the tin lines (0.73-0.76) compared to the free-tillering sisters (0.62-0.63). At maximum tiller number, the red: far-red ratio (light quality stimulus that is thought to induce the cessation of tillering) at the plant-base was 0.18-0.22 in tin lines and 0.09-0.11 in free-tillering lines at levels of photosynthetic active radiation of 49-53% and 30-33%, respectively. The tin lines intercepted less radiation compared to their free-tillering sisters once genotypic differences in tiller numbers had established, and maintained green leaf area in the lower canopy later into the season. Greater light extinction coefficients (k) in tin lines prior to, but reduced k after, spike emergence indicated that differences in light interception between NILs contrasting in tin cannot be explained by leaf area alone but that geometric and optical canopy properties contributed. The careful characterization of specifically-developed NILs is refining the development of a physiology-based model for tillering to improve understanding of the value of architectural traits for use in cereal improvement.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer.

PubMed

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival ( p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation ( p < 0.001) and T cell activation ( p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8 + T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer

PubMed Central

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

ABSTRACT Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival (p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation (p < 0.001) and T cell activation (p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8+ T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis. PMID:28507798

A comparative study of fine polished stainless steel, TiN and TiN/Ag surfaces: adhesion and attachment strength of Listeria monocytogenes as well as anti-listerial effect.

PubMed

Skovager, Anne; Whitehead, Kathryn; Wickens, David; Verran, Joanna; Ingmer, Hanne; Arneborg, Nils

2013-09-01

Magnetron sputtering was used to produce nanocomposite TiN and TiN/Ag coatings on stainless steel surfaces. The surface chemistry (EDX), physicochemical properties (contact angles), topography and roughness parameters (WLP and AFM) of the fine polished stainless steel (FPSS), TiN and TiN/8.6 at.% Ag surfaces were examined. Real-time initial adhesion of two Listeria monocytogenes strains (EGDe and 64) to the three surfaces was determined under flow conditions, and their attachment strength after adhesion was measured using atomic force microscopy (AFM). The anti-listerial properties of the surfaces were determined using LIVE/DEAD staining. Our results demonstrate that FPSS, TiN and TiN/8.6 at.% Ag possessed different surface properties, which may influence both attachment strength and anti-listerial properties. There were no significant (p>0.05) differences in the initial adhesion of the two L. monocytogenes strains to the three different surfaces. Attachment studies showed that the two L. monocytogenes strains did not attach to FPSS under wetted conditions. However, both strains attached to TiN and TiN/8.6 at.% Ag surfaces, although with less strength to TiN/8.6 at.% Ag than to TiN surfaces. The TiN/8.6 at.% Ag surface showed marked anti-listerial properties as compared with FPSS and TiN. Initial adhesion, attachment strength and anti-listerial properties were found to be strain dependent. Copyright © 2013 Elsevier B.V. All rights reserved.

Tin recovery from tin slag using electrolysis method

NASA Astrophysics Data System (ADS)

Jumari, Arif; Purwanto, Agus; Nur, Adrian; Budiman, Annata Wahyu; Lerian, Metty; Paramita, Fransisca A.

2018-02-01

The process in industry, including in mining industry, would surely give negative effect such as waste polluting to the environment. Some of waste could be potentially reutilized to be a commodity with the higher economic value. Tin slag is one of them. The aim of this research was to recover the tin contained in tin slag. Before coming to the electrolysis, tin slag must be treated by dissolution. The grinded tin slag was dissolved into HCl solution to form a slurry. During dissolution, the slurry was agitated and heated, and finally filtered. The filtrate obtained was then electrolyzed. During the process of electrolysis, solid material precipitated on the used cathode. The precipitated solid was then separated and dried. The solid was then analyzed using XRD, XRF and SEM. The XRD analysis showed that the longest time of dissolution and electrolysis the highest the purity obtained in the product. The SEM analysis showed that the longest time of electrolysis the smallest tin particle obtained. Optimum time achieved in this research was 2 hours for the recovering time and 3 hours for the electrolysis time, with 9% tin recovered.

Transcription instability in high-risk neuroblastoma is associated with a global perturbation of chromatin domains.

PubMed

Zanon, Carlo; Tonini, Gian Paolo

2017-11-01

Chromosome instability has a pivotal role among the hallmarks of cancer, but its transcriptional counterpart is rarely considered a relevant factor in cell destabilization. To examine transcription instability (TIN), we first devised a metric we named TIN index and used it to evaluate TIN on a dataset containing more than 500 neuroblastoma samples. We found that metastatic tumors from high-risk (HR) patients are characterized by significantly different TIN index values compared to low/intermediate-risk patients. Our results indicate that the TIN index is a good predictor of neuroblastoma patient's outcome, and a related TIN index gene signature (TIN-signature) is also able to predict the neuroblastoma patient's outcome with high confidence. Interestingly, we find that TIN-signature genes have a strong positional association with superenhancers in neuroblastoma tumors. Finally, we show that TIN is linked to chromatin structural domains and interferes with their integrity in HR neuroblastoma patients. This novel approach to gene expression analysis broadens the perspective of genome instability investigations to include functional aspects. © 2017 The Authors. Published by FEBS Press and John Wiley & Sons Ltd.

Advances in aluminum hydroxide-based adjuvant research and its mechanism.

PubMed

He, Peng; Zou, Yening; Hu, Zhongyu

2015-01-01

In the past few decades, hundreds of materials have been tried as adjuvant; however, only aluminum-based adjuvants continue to be used widely in the world. Aluminum hydroxide, aluminum phosphate and alum constitute the main forms of aluminum used as adjuvants. Among these, aluminum hydroxide is the most commonly used chemical as adjuvant. In spite of its wide spread use, surprisingly, the mechanism of how aluminum hydroxide-based adjuvants exert their beneficial effects is still not fully understood. Current explanations for the mode of action of aluminum hydroxide-based adjuvants include, among others, the repository effect, pro-phagocytic effect, and activation of the pro-inflammatory NLRP3 pathway. These collectively galvanize innate as well as acquired immune responses and activate the complement system. Factors that have a profound influence on responses evoked by aluminum hydroxide-based adjuvant applications include adsorption rate, strength of the adsorption, size and uniformity of aluminum hydroxide particles, dosage of adjuvant, and the nature of antigens. Although vaccines containing aluminum hydroxide-based adjuvants are beneficial, sometimes they cause adverse reactions. Further, these vaccines cannot be stored frozen. Until recently, aluminum hydroxide-based adjuvants were known to preferentially prime Th2-type immune responses. However, results of more recent studies show that depending on the vaccination route, aluminum hydroxide-based adjuvants can enhance both Th1 as well as Th2 cellular responses. Advances in systems biology have opened up new avenues for studying mechanisms of aluminum hydroxide-based adjuvants. These will assist in scaling new frontiers in aluminum hydroxide-based adjuvant research that include improvement of formulations, use of nanoparticles of aluminum hydroxide and development of composite adjuvants.

Advances in aluminum hydroxide-based adjuvant research and its mechanism

PubMed Central

He, Peng; Zou, Yening; Hu, Zhongyu

2015-01-01

In the past few decades, hundreds of materials have been tried as adjuvant; however, only aluminum-based adjuvants continue to be used widely in the world. Aluminum hydroxide, aluminum phosphate and alum constitute the main forms of aluminum used as adjuvants. Among these, aluminum hydroxide is the most commonly used chemical as adjuvant. In spite of its wide spread use, surprisingly, the mechanism of how aluminum hydroxide-based adjuvants exert their beneficial effects is still not fully understood. Current explanations for the mode of action of aluminum hydroxide-based adjuvants include, among others, the repository effect, pro-phagocytic effect, and activation of the pro-inflammatory NLRP3 pathway. These collectively galvanize innate as well as acquired immune responses and activate the complement system. Factors that have a profound influence on responses evoked by aluminum hydroxide-based adjuvant applications include adsorption rate, strength of the adsorption, size and uniformity of aluminum hydroxide particles, dosage of adjuvant, and the nature of antigens. Although vaccines containing aluminum hydroxide-based adjuvants are beneficial, sometimes they cause adverse reactions. Further, these vaccines cannot be stored frozen. Until recently, aluminum hydroxide-based adjuvants were known to preferentially prime Th2-type immune responses. However, results of more recent studies show that depending on the vaccination route, aluminum hydroxide-based adjuvants can enhance both Th1 as well as Th2 cellular responses. Advances in systems biology have opened up new avenues for studying mechanisms of aluminum hydroxide-based adjuvants. These will assist in scaling new frontiers in aluminum hydroxide-based adjuvant research that include improvement of formulations, use of nanoparticles of aluminum hydroxide and development of composite adjuvants. PMID:25692535

Mineral of the month: tin

USGS Publications Warehouse

Carlin, James F.

2005-01-01

Tin was one of the first metals discovered by humans and, like most metals, tin is rarely used by itself. Most tin is used as a protective coating or as an alloy with other metals in a diverse range of commercial and defense applications.

Superlative TINs

NASA Technical Reports Server (NTRS)

Chamberlin, R.

2002-01-01

TIN is short for 'triangulated irregular network,' which is a piecewise planar model of a surface. If properly constructed, a TIN can be more than 30 times as efficient as a regular triangulation. In our project (a ground combat simulation to support U.S. Army training exercises), the TIN is used to represent the Earth's surface and is used primarily to determine whether line of sight is blocked by terrain. High efficiency requires accurate identification of ridgelines with as few triangles as possible. The work currently in progress is the implementation of a TINning process that we hope will produce superlative TINs. This presentation describes that process.

Tin whiskers in electronic circuits

NASA Astrophysics Data System (ADS)

Stupian, Gary W.

1992-12-01

Fibrous, conducting 'whiskers' often grow on pure tin plating. These tin whiskers have, for many years, been known to pose a reliability problem in electronic circuitry; therefore, the use of pure tin coatings in any critical electronic application is not recommended. Despite the warnings of the experts, tin plating is still found on electronic and mechanical components and problems with whiskers still arise. This document summarizes what is known about the growth of tin whiskers. A number of factors (e.g., coating thickness, plating conditions) are thought to be important in determining whether whiskers will grow. Although tin whiskers have been investigated from some decades, there is still disagreement on the effects of virtually every coating parameter. There is no disagreement, however, on the essential fact that it is very difficult to predict with certainty whether whiskers will grow on any specific tin-plated component, which of course is the basis of the 'experts' advice not to use pure tin plating. If tin-plated components are found in an electronic system, replacement is the safest policy. Some additional recommendations to minimize risk are presented here that may be of use in situations in which replacement of all suspect components is not the option of choice because of cost or schedule constraints.

Antibacterial action of calcium hydroxide vehicles and calcium hydroxide pastes.

PubMed

Pacios, María Gabriela; Silva, Clara; López, María Elena; Cecilia, Marta

2012-11-01

To evaluate the in vitro action of vehicles alone and with calcium hydroxide against different bacterial species. Agar plates were inoculated with the microbial suspensions, and wells were made and filled with the calcium hydroxide pastes and the vehicles used to prepare the pastes. The zones of inhibited bacterial growth were recorded, and the resulting measurements were statistically analyzed. Enterococcus faecalis was the most resistant microorganism to all medicaments. Calcium hydroxide + p-monochlorophenol; calcium hydroxide + p-monochlorophenol-propylene glycol pastes; and p-monochlorophenol, p-monochlorophenol-propylene glycol, and chlorhexidine gluconate gel alone showed the largest zones of inhibition against all the tested microorganisms. The vehicle used to prepare the calcium hydroxide paste might contribute to its antibacterial action. Chlorhexidine gluconate gel used alone, and camphorated p-monochlorophenol and camphorated p-monochlorophenol-propylene glycol as vehicles of calcium hydroxide, could be recommended, in an antimicrobial sense. © 2012 Wiley Publishing Asia Pty Ltd.

Friction and wear of tin and tin alloys from minus 100 C to 150 C

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1975-01-01

Sliding friction experiments were conducted with an iron (110) single-crystal pin sliding on single and polycrystalline tin and tin alloys. Specimens were examined at various ambient temperatures from -100 to 150 C. Applied loads varied from 1 to 50 grams, and sliding velocity was constant at 0.7 mm/min. Results indicate that the crystal transformation of tin influences the friction coefficient. Friction was higher for the diamond structure (gray tin) than it was for the body-centered tetragonal structure (white tin). Bismuth arrested the crystal transformation, which resulted in constant friction over the temperature range -100 to 150 C. Both copper and aluminum enhanced the kinetics of transformation, with aluminum producing a nearly twofold change in friction with the crystal transformation.

Cu2+ ions as a paramagnetic probe to study the surface chemical modification process of layered double hydroxides and hydroxide salts with nitrate and carboxylate anions.

PubMed

Arizaga, Gregorio Guadalupe Carbajal; Mangrich, Antonio Salvio; Wypych, Fernando

2008-04-01

A layered zinc hydroxide nitrate (Zn5(OH)8(NO3)2.2H2O) and a layered double hydroxide (Zn/Al-NO3) were synthesized by coprecipitation and doped with different amounts of Cu2+ (0.2, 1, and 10 mol%), as paramagnetic probe. Although the literature reports that the nitrate ion is free (with D3h symmetry) between the layers of these two structures, the FTIR spectra of two zinc hydroxide nitrate samples show the C2v symmetry for the nitrate ion, whereas the g ||/A || value in the EPR spectra of Cu2+ is high. This fact suggests bonding of some nitrate ions to the layers of the zinc hydroxide nitrate. The zinc hydroxide nitrate was used as matrix in the intercalation reaction with benzoate, o-chlorobenzoate, and o-iodobenzoate ions. FTIR spectra confirm the ionic exchange reaction and the EPR spectroscopy reveals bonding of the organic ions to the inorganic layers of the zinc hydroxide nitrate, while the layered double hydroxides show only exchange reactions.

A review of tin oxide-based catalytic systems: Preparation, characterization and catalytic behavior

NASA Technical Reports Server (NTRS)

Hoflund, Gar B.

1987-01-01

This paper reviews the important aspects of the preparation, characterization and catalytic behavior of tin oxide-based catalytic systems including doped tin oxide, mixed oxides which contain tin oxide, Pt supported on tin oxide and Pt/Sn supported on alumina. These systems have a broad range of applications and are continually increasing in importance. However, due to their complex nature, much remains to be understood concerning how they function catalytically.

Contributions of Stress and Oxidation on the Formation of Whiskers in Pb-free Solders

DTIC Science & Technology

2016-01-29

environmental factors influencing formation of tin whiskers on electrodeposited lead free, tin coatings over copper (or copper containing) substrates is the...Oxidation on the Formation of Whiskers in Pb‐free Solders,” WP-1754 15. SUBJECT TERMS Tin Whiskers, Residual Stress, Environmental Degradation 16...showing the surface of a tin film with whisker .................... 2 Figure 2: SEM Micrograph of Tin film on Copper Substrate cross-sectioned by FIB

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

77 FR 3725 - Proposed Significant New Use Rules on Certain Chemical Substances; Extension of Comment Period

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-25

... chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01- 2) and rutile, tin zinc, sodium... substances rutile, tin zinc, calcium- doped (CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (CAS No...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

Metallic tin quantum sheets confined in graphene toward high-efficiency carbon dioxide electroreduction

NASA Astrophysics Data System (ADS)

Lei, Fengcai; Liu, Wei; Sun, Yongfu; Xu, Jiaqi; Liu, Katong; Liang, Liang; Yao, Tao; Pan, Bicai; Wei, Shiqiang; Xie, Yi

2016-09-01

Ultrathin metal layers can be highly active carbon dioxide electroreduction catalysts, but may also be prone to oxidation. Here we construct a model of graphene confined ultrathin layers of highly reactive metals, taking the synthetic highly reactive tin quantum sheets confined in graphene as an example. The higher electrochemical active area ensures 9 times larger carbon dioxide adsorption capacity relative to bulk tin, while the highly-conductive graphene favours rate-determining electron transfer from carbon dioxide to its radical anion. The lowered tin-tin coordination numbers, revealed by X-ray absorption fine structure spectroscopy, enable tin quantum sheets confined in graphene to efficiently stabilize the carbon dioxide radical anion, verified by 0.13 volts lowered potential of hydroxyl ion adsorption compared with bulk tin. Hence, the tin quantum sheets confined in graphene show enhanced electrocatalytic activity and stability. This work may provide a promising lead for designing efficient and robust catalysts for electrolytic fuel synthesis.

Platelet composite coatings for tin whisker mitigation

DOE PAGES

Rohwer, Lauren E. S.; Martin, James E.

2015-09-14

In this study, reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results formore » several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF 2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.« less

Platelet Composite Coatings for Tin Whisker Mitigation

NASA Astrophysics Data System (ADS)

Rohwer, Lauren E. S.; Martin, James E.

2015-11-01

Reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results for several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.

Method and system for producing hydrogen using sodium ion separation membranes

DOEpatents

Bingham, Dennis N; Klingler, Kerry M; Turner, Terry D; Wilding, Bruce M; Frost, Lyman

2013-05-21

A method of producing hydrogen from sodium hydroxide and water is disclosed. The method comprises separating sodium from a first aqueous sodium hydroxide stream in a sodium ion separator, feeding the sodium produced in the sodium ion separator to a sodium reactor, reacting the sodium in the sodium reactor with water, and producing a second aqueous sodium hydroxide stream and hydrogen. The method may also comprise reusing the second aqueous sodium hydroxide stream by combining the second aqueous sodium hydroxide stream with the first aqueous sodium hydroxide stream. A system of producing hydrogen is also disclosed.

The effect of polymers onto the size of zinc layered hydroxide salt and its calcined product

NASA Astrophysics Data System (ADS)

Hussein, Mohd Zobir bin; Ghotbi, Mohammad Yeganeh; Yahaya, Asmah Hj; Abd Rahman, Mohd Zaki

2009-02-01

Zinc hydroxide nitrate, a brucite-like layered material was synthesized using pH control method. Poly(vinyl alcohol) and poly(ethylene glycol) were used at various percentages as size decreasing agents during the synthesis of zinc hydroxide nitrate. SEM and PXRD showed the decrease of size and thickness of the resultant zinc hydroxide nitrates. TG and surface area data confirmed the decrease of the particle sizes, too. When zinc hydroxide nitrates were heat treated at 500 °C, the physical properties of nano zinc oxides obtained depended on the parent material, zinc hydroxide nitrate.

Polynucleotides encoding TRF1 binding proteins

DOEpatents

Campisi, Judith; Kim, Sahn-Ho

2002-01-01

The present invention provides a novel telomere associated protein (Trf1-interacting nuclear protein 2 "Tin2") that hinders the binding of Trf1 to its specific telomere repeat sequence and mediates the formation of a Tin2-Trf1-telomeric DNA complex that limits telomerase access to the telomere. Also included are the corresponding nucleic acids that encode the Tin2 of the present invention, as well as mutants of Tin2. Methods of making, purifying and using Tin2 of the present invention are described. In addition, drug screening assays to identify drugs that mimic and/or complement the effect of Tin2 are presented.

Optical Properties and Plasmonic Performance of Titanium Nitride

PubMed Central

Patsalas, Panos; Kalfagiannis, Nikolaos; Kassavetis, Spyros

2015-01-01

Titanium nitride (TiN) is one of the most well-established engineering materials nowadays. TiN can overcome most of the drawbacks of palsmonic metals due to its high electron conductivity and mobility, high melting point and due to the compatibility of its growth with Complementary Metal Oxide Semiconductor (CMOS) technology. In this work, we review the dielectric function spectra of TiN and we evaluate the plasmonic performance of TiN by calculating (i) the Surface Plasmon Polariton (SPP) dispersion relations and (ii) the Localized Surface Plasmon Resonance (LSPR) band of TiN nanoparticles, and we demonstrate a significant plasmonic performance of TiN.

Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim J.; Asfour, Shihab S.; Onar, Arzu; Bayliss, Jon A.; Ludwig, Larry L.; Wright, Maria C.

2009-01-01

To comply with lead-free legislation, many manufacturers have converted from tin-lead to pure tin finishes of electronic components. However, pure tin finishes have a greater propensity to grow tin whiskers than tin-lead finishes. Since tin whiskers present an electrical short circuit hazard in electronic components, simulations have been developed to quantify the risk of said short circuits occurring. Existing risk simulations make the assumption that when a free tin whisker has bridged two adjacent exposed electrical conductors, the result is an electrical short circuit. This conservative assumption is made because shorting is a random event that had an unknown probability associated with it. Note however that due to contact resistance electrical shorts may not occur at lower voltage levels. In our first article we developed an empirical probability model for tin whisker shorting. In this paper, we develop a more comprehensive empirical model using a refined experiment with a larger sample size, in which we studied the effect of varying voltage on the breakdown of the contact resistance which leads to a short circuit. From the resulting data we estimated the probability distribution of an electrical short, as a function of voltage.

Demonstration of high-performance p-type tin oxide thin-film transistors using argon-plasma surface treatments

NASA Astrophysics Data System (ADS)

Bae, Sang-Dae; Kwon, Soo-Hun; Jeong, Hwan-Seok; Kwon, Hyuck-In

2017-07-01

In this work, we investigated the effects of low-temperature argon (Ar)-plasma surface treatments on the physical and chemical structures of p-type tin oxide thin-films and the electrical performance of p-type tin oxide thin-film transistors (TFTs). From the x-ray photoelectron spectroscopy measurement, we found that SnO was the dominant phase in the deposited tin oxide thin-film, and the Ar-plasma treatment partially transformed the tin oxide phase from SnO to SnO2 by oxidation. The resistivity of the tin oxide thin-film increased with the plasma-treatment time because of the reduced hole concentration. In addition, the root-mean-square roughness of the tin oxide thin-film decreased as the plasma-treatment time increased. The p-type oxide TFT with an Ar-plasma-treated tin oxide thin-film exhibited excellent electrical performance with a high current on-off ratio (5.2 × 106) and a low off-current (1.2 × 10-12 A), which demonstrates that the low-temperature Ar-plasma treatment is a simple and effective method for improving the electrical performance of p-type tin oxide TFTs.

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

An Investigation of the Electrical Short Circuit Characteristics of Tin Whiskers

NASA Technical Reports Server (NTRS)

Courey, Karim J.

2008-01-01

In this experiment, an empirical model to quantify the probability of occurrence of an electrical short circuit from tin whiskers as a function of voltage was developed. This model can be used to improve existing risk simulation models FIB and TEM images of a tin whisker confirm the rare polycrystalline structure on one of the three whiskers studied. FIB cross-section of the card guides verified that the tin finish was bright tin.

Effect of Tin, Copper and Boron on the Hot Ductility of 20CrMnTi Steel between 650 °C and 1100 °C

NASA Astrophysics Data System (ADS)

Peng, Hong-bing; Chen, Wei-qing; Chen, Lie; Guo, Dong

2015-02-01

The hot ductility of 20CrMnTi steel with x% tin, y% copper and z ppm boron (x = 0, 0.02; y = 0, 0.2; z = 0, 60) was investigated. The results show that tin and copper in 20CrMnTi steel are detrimental to its hot ductility while adding boron can eliminate the adverse effect and enhance hot ductility greatly. Tin is found to segregate to the boundaries tested by EPMA in 20CrMnTi steel containing tin and copper and tin-segregation is suppressed by adding boron, moreover, copper was found not to segregate to boundaries, however, fine copper sulfide was found from carbon extraction replicas using TEM. The adverse effect of tin and copper on the hot ductility was due mainly to tin segregation and fine copper sulfide in the steel. The proeutectoid ferrite film precipitating along the austenite grain boundary causes the ductility trough of the three examined steels. Tin and copper in 20CrMnTi steel can retard the occurrence of dynamic recrystallization (DRX) while boron-addition can compensate for that change. The beneficial effect of boron on 20CrMnTi steel containing tin and copper might be ascribed to the fact that boron segregates to grain boundaries, accelerates onset of DRX, retards austenite/ferrite transformation and promotes intragranular nucleation of ferrite.

Precipitation Behaviors of TiN Inclusion in GCr15 Bearing Steel Billet

NASA Astrophysics Data System (ADS)

Tian, Qianren; Wang, Guocheng; Zhao, Yang; Li, Jing; Wang, Qi

2018-06-01

There are many types of non-metallic TiN-based inclusions observed in GCr15 bearing steel, including single-particle TiN, multi-particle polymerized TiN, and complex inclusions like TiN-MnS, TiN-MgO-MgAl2O4 (TiN-MgO-MA), and TiN-MgAl2O4-MnS (TiN-MA-MnS). Thermodynamic calculations suggest that single-particle TiN precipitates dominate the mushy zone of GCr15 bearing steel. Kinetic calculations regarding TiN growth suggest that the final size of the single-particle TiN ranges between 1 and 6 μm in the initial concentration range of [pct Ti] = 0.0060 to 0.0079 and [pct N] = 0.0049 to 0.0070, at 1620 to 1640 K and a local cooling rate of 0.5 to 10 K/s. The multi-particle polymerized TiN are formed by single TiN particles in three stages: single-particle TiN inclusions approach each other drawn by the cavity bridge force (CBF), local active angles consolidate, and neck region sintering occurs. Based on the thermodynamic calculations of TiN, MnS, and MgO precipitation, the formation behaviors of complex inclusions of TiN-MnS, TiN-MgO-MA, and TiN-MA-MnS were investigated.

40 CFR 415.310 - Applicability; description of the calcium hydroxide production subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... calcium hydroxide production subcategory. 415.310 Section 415.310 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Calcium Hydroxide Production Subcategory § 415.310 Applicability; description of the calcium hydroxide production subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 415.310 - Applicability; description of the calcium hydroxide production subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... calcium hydroxide production subcategory. 415.310 Section 415.310 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Calcium Hydroxide Production Subcategory § 415.310 Applicability; description of the calcium hydroxide production subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 415.310 - Applicability; description of the calcium hydroxide production subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calcium hydroxide production subcategory. 415.310 Section 415.310 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Calcium Hydroxide Production Subcategory § 415.310 Applicability; description of the calcium hydroxide production subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 415.310 - Applicability; description of the calcium hydroxide production subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... calcium hydroxide production subcategory. 415.310 Section 415.310 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Calcium Hydroxide Production Subcategory § 415.310 Applicability; description of the calcium hydroxide production subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 415.310 - Applicability; description of the calcium hydroxide production subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calcium hydroxide production subcategory. 415.310 Section 415.310 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Calcium Hydroxide Production Subcategory § 415.310 Applicability; description of the calcium hydroxide production subcategory. The provisions of this subpart are applicable to discharges...

77 FR 32998 - Tin- and Chromium-Coated Steel Sheet From Japan

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-04

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-860 (Second Review)] Tin- and Chromium... order on tin- and chromium-coated steel sheet from Japan would be likely to lead to continuation or... USITC Publication 4325 (May 2012), entitled Tin- and Chromium-Coated Steel Sheet from Japan...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 15 2013-04-01 2013-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 15 2011-04-01 2011-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 15 2012-04-01 2012-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to waters of the...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to waters of the...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 15 2014-04-01 2014-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

An Empirical Model for Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim; Wright, Clara; Asfour, Shihab; Onar, Arzu; Bayliss, Jon; Ludwig, Larry

2009-01-01

In this experiment, an empirical model to quantify the probability of occurrence of an electrical short circuit from tin whiskers as a function of voltage was developed. This empirical model can be used to improve existing risk simulation models. FIB and TEM images of a tin whisker confirm the rare polycrystalline structure on one of the three whiskers studied. FIB cross-section of the card guides verified that the tin finish was bright tin.

Microwave plasma CVD of NANO structured tin/carbon composites

DOEpatents

Marcinek, Marek [Warszawa, PL; Kostecki, Robert [Lafayette, CA

2012-07-17

A method for forming a graphitic tin-carbon composite at low temperatures is described. The method involves using microwave radiation to produce a neutral gas plasma in a reactor cell. At least one organo tin precursor material in the reactor cell forms a tin-carbon film on a supporting substrate disposed in the cell under influence of the plasma. The three dimensional carbon matrix material with embedded tin nanoparticles can be used as an electrode in lithium-ion batteries.

Preparation of textural lamellar tin deposits via electrodeposition

NASA Astrophysics Data System (ADS)

Wen, Xiaoyu; Pan, Xiaona; Wu, Libin; Li, Ruinan; Wang, Dan; Zhang, Jinqiu; Yang, Peixia

2017-06-01

Lamellar tin deposits were prepared by galvanostatical electroplating from the aqueous acidic-sulfate bath, with gelatin and benzalacetone dissolved in ethanol (ABA+EtOH) as additive, and their morphologies were investigated by scanning electron microscopy. Cathodic polarization curves revealed that the absorbability of ABA+EtOH on the cathode surface was higher than that of gelatin. X-ray diffraction analysis indicated preferred orientations of tin growth led to the formation of lamellar structure and distortion of tin lattice. The growth mechanism of lamellar tin was also discussed.

NASA GSFC Tin Whisker Homepage http://nepp.nasa.gov/whisker

NASA Technical Reports Server (NTRS)

Shaw, Harry

2000-01-01

The NASA GSFC Tin Whisker Homepage provides general information and GSFC Code 562 experimentation results regarding the well known phenomenon of tin whisker formation from pure tin plated substrates. The objective of this www site is to provide a central repository for information pertaining to this phenomenon and to provide status of the GSFC experiments to understand the behavior of tin whiskers in space environments. The Tin Whisker www site is produced by Code 562. This www site does not provide information pertaining to patented or proprietary information. All of the information contained in this www site is at the level of that produced by industry and university researchers and is published at international conferences.

Effect of thiourea on electrochemical nucleation and electrochemical impedance spectroscopy of electrodeposited tin on a copper substrate in a sulfate bath.

PubMed

Lee, Mi-Ri; Na, Seong-Hun; Park, Hwa-Sun; Suh, Su-Jeong

2014-12-01

The effect of thiourea on the electrochemical nucleation of tin on a copper substrate from a sulfate bath was studied using voltammetry, chronoamperometry, electrochemical impedance spectroscopy, and scanning electron microscopy. Without thiourea, electrodeposition of tin showed very poor surface coverage. However, re-nucleation and growth of tin occurred after the addition of thiourea. In particular, very rapid re-nucleation and growth behavior of tin were observed when up to 6 g/L of thiourea was added. Furthermore, impedance analysis allowed the estimation of the change in the growth behavior of tin when up to 6 g/L of thiourea was added.

Structural studies of supported tin catalysts

NASA Astrophysics Data System (ADS)

Nava, Noel; Viveros, Tomás

1999-11-01

Tin oxide was supported on aluminium oxide, titanium oxide, magnesium oxide and silicon oxide, and the resulting interactions between the components in the prepared samples and after reduction were characterized by Mössbauer spectroscopy. It was observed that in the oxide state, tin is present as SnO2 on alumina, magnesia and silica, but on titania tin occupies Ti sites in the structure. After hydrogen treatment at high temperatures, tin is reduced from Sn(4) to Sn(2) on alumina and titania; it is reduced from Sn(4) to Sn(0) on silica, and is practically not reduced on magnesia. These results reveal the degree of interaction between tin and the different supports studied.

21 CFR 582.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Magnesium hydroxide. 582.1428 Section 582.1428 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1428 Magnesium hydroxide. (a) Product. Magnesium hydroxide. (b) Conditions of use. This...

40 CFR 721.10504 - Surface modified magnesium hydroxide (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Surface modified magnesium hydroxide... Specific Chemical Substances § 721.10504 Surface modified magnesium hydroxide (generic). (a) Chemical... as surface modified magnesium hydroxide (PMN P-06-682) is subject to reporting under this section for...

21 CFR 582.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Magnesium hydroxide. 582.1428 Section 582.1428 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1428 Magnesium hydroxide. (a) Product. Magnesium hydroxide. (b) Conditions of use. This...

21 CFR 582.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Magnesium hydroxide. 582.1428 Section 582.1428 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1428 Magnesium hydroxide. (a) Product. Magnesium hydroxide. (b) Conditions of use. This...

40 CFR 721.10573 - Magnesium hydroxide surface treated with substituted alkoxysilanes (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Magnesium hydroxide surface treated... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10573 Magnesium hydroxide surface... to reporting. (1) The chemical substance identified generically as magnesium hydroxide surface...

21 CFR 582.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Magnesium hydroxide. 582.1428 Section 582.1428 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1428 Magnesium hydroxide. (a) Product. Magnesium hydroxide. (b) Conditions of use. This...

40 CFR 721.10504 - Surface modified magnesium hydroxide (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Surface modified magnesium hydroxide... Specific Chemical Substances § 721.10504 Surface modified magnesium hydroxide (generic). (a) Chemical... as surface modified magnesium hydroxide (PMN P-06-682) is subject to reporting under this section for...

40 CFR 721.10573 - Magnesium hydroxide surface treated with substituted alkoxysilanes (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Magnesium hydroxide surface treated... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10573 Magnesium hydroxide surface... to reporting. (1) The chemical substance identified generically as magnesium hydroxide surface...

21 CFR 582.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Magnesium hydroxide. 582.1428 Section 582.1428 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1428 Magnesium hydroxide. (a) Product. Magnesium hydroxide. (b) Conditions of use. This...

21 CFR 582.1205 - Calcium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Calcium hydroxide. 582.1205 Section 582.1205 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1205 Calcium hydroxide. (a) Product. Calcium hydroxide. (b) Conditions of use. This...

21 CFR 582.1631 - Potassium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

21 CFR 582.1631 - Potassium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

21 CFR 582.1631 - Potassium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

21 CFR 582.1631 - Potassium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

21 CFR 582.1631 - Potassium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

Process for changing caking coals to noncaking coals

DOEpatents

Beeson, Justin L.

1980-01-01

Caking coals are treated in a slurry including alkaline earth metal hydroxides at moderate pressures and temperatures in air to form noncaking carbonaceous material. Hydroxides such as calcium hydroxide, magnesium hydroxide or barium hydroxide are contemplated for slurrying with the coal to interact with the agglomerating constituents. The slurry is subsequently dewatered and dried in air at atmospheric pressure to produce a nonagglomerating carbonaceous material that can be conveniently handled in various coal conversion and combustion processes.

Organic derivatives of tin (II/IV): Investigation of their structure

NASA Astrophysics Data System (ADS)

Szirtes, L.; Megyeri, J.; Kuzmann, E.; Beck, A.

2011-07-01

The structures of tin(II)-oxalate, tin(IV)Na-EDTA and tin(IV)Na 8-inositol hexaphosphate were investigated using XRD analysis. Samples were identified using the Mössbauer study, thermal analysis and FTIR spectrometry. The Mössbauer study determined two different oxidation states of tin atoms, and consequently two different tin surroundings in the end products. The tin oxalate was found to be orthorhombic with space group Pnma, a=9.2066(3) Å, b=9.7590(1) Å, c=13.1848(5) Å, V=1184.62 Å 3 and Z=8. SnNa-EDTA was found to be monoclinic with space group P2 1/c 1, a=10.7544(3) Å, b=10.1455(3) Å, c=16.5130(6) Å, β=98.59(2)°, V=1781.50(4) Å 3 and Z=4. Sn(C 6H 6Na 8O 24P 6) was found to be amorphous.

A charge optimized many-body potential for titanium nitride (TiN).

PubMed

Cheng, Y-T; Liang, T; Martinez, J A; Phillpot, S R; Sinnott, S B

2014-07-02

This work presents a new empirical, variable charge potential for TiN systems in the charge-optimized many-body potential framework. The potential parameters were determined by fitting them to experimental data for the enthalpy of formation, lattice parameters, and elastic constants of rocksalt structured TiN. The potential does a good job of describing the fundamental physical properties (defect formation and surface energies) of TiN relative to the predictions of first-principles calculations. This potential is used in classical molecular dynamics simulations to examine the interface of fcc-Ti(0 0 1)/TiN(0 0 1) and to characterize the adsorption of oxygen atoms and molecules on the TiN(0 0 1) surface. The results indicate that the potential is well suited to model TiN thin films and to explore the chemistry associated with their oxidation.

Effect of doping of tin on optoelectronic properties of indium oxide: DFT study

NASA Astrophysics Data System (ADS)

Tripathi, Madhvendra Nath

2015-06-01

Indium tin oxide is widely used transparent conductor. Experimentally observed that 6% tin doping in indium oxide is suitable for optoelectronic applications and more doping beyond this limit degrades the optoelectronic property. The stoichiometry (In32-xSnxO48+x/2; x=0-6) is taken to understand the change in lattice parameter, electronic structure, and optical property of ITO. It is observed that lattice parameter increases and becomes constant after 6% tin doping that is in good agreement of the experimental observation. The electronic structure calculation shows that the high tin doping in indium oxide adversely affects the dispersive nature of the bottom of conduction band of pure indium oxide and decreases the carrier mobility. Optical calculations show that transmittance goes down upto 60% for the tin concentration more than 6%. The present paper shows that how more than 6% tin doping in indium oxide adversely affects the optoelectronic property of ITO.

Controllable synthesis of layered Co-Ni hydroxide hierarchical structures for high-performance hybrid supercapacitors

NASA Astrophysics Data System (ADS)

Yuan, Peng; Zhang, Ning; Zhang, Dan; Liu, Tao; Chen, Limiao; Ma, Renzhi; Qiu, Guanzhou; Liu, Xiaohe

2016-01-01

A facile solvothermal method is developed for synthesizing layered Co-Ni hydroxide hierarchical structures by using hexamethylenetetramine (HMT) as alkaline reagent. The electrochemical measurements reveal that the specific capacitances of layered bimetallic (Co-Ni) hydroxides are generally superior to those of layered monometallic (Co, Ni) hydroxides. The as-prepared Co0.5Ni0.5 hydroxide hierarchical structures possesses the highest specific capacitance of 1767 F g-1 at a galvanic current density of 1 A g-1 and an outstanding specific capacitance retention of 87% after 1000 cycles. In comparison with the dispersed nanosheets of Co-Ni hydroxide, layered hydroxide hierarchical structures show much superior electrochemical performance. This study provides a promising method to construct hierarchical structures with controllable transition-metal compositions for enhancing the electrochemical performance in hybrid supercapacitors.

77 FR 13156 - Carolina Power & Light Company; Shearon Harris Nuclear Power Plant, Unit 1; Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

... percent) and niobium (~1 percent). The elimination of tin has resulted in superior corrosion resistance and reduced irradiation-induced growth relative to both standard zircaloy (1.7 percent tin) and low-tin zircaloy (1.2 percent tin). The addition of niobium increases ductility, which is desirable to...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

78 FR 52802 - Tin T. Win, M.D., Dismissal of Proceeding

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-26

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Tin T. Win, M.D., Dismissal of Proceeding On... Cause and Immediate Suspension of Registration to Tin T. Win, M.D. (hereinafter, Registrant), of Lake... order that the Order to Show Cause and Immediate Suspension of Registration issued to Tin T. Win, M.D...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

77 FR 66449 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-05

...) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with the...), the Government's primary registrant database; c. Provide your DUNS number and TIN on your application... you are a corporate entity, agency, institution, or organization, you can obtain a TIN from the...

77 FR 27031 - Applications for New Awards; Centers for Independent Living

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-08

... Number (TIN); b. Register both your DUNS number and TIN with the Central Contractor Registry (CCR), the Government's primary registrant database; c. Provide your DUNS number and TIN on your application; and d..., agency, institution, or organization, you can obtain a TIN from the Internal Revenue Service. If you are...

38 CFR 61.12 - Capital grant application packages-threshold requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... contains the Employer Identification Number or Taxpayer Identification Number (EIN/TIN) that corresponds to... must provide such an IRS determination letter, which includes their EIN/TIN. Applicants that apply under a group EIN/TIN must be identified by the parent EIN/TIN as a member or sub-unit of the parent EIN...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

38 CFR 61.12 - Capital grant application packages-threshold requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... contains the Employer Identification Number or Taxpayer Identification Number (EIN/TIN) that corresponds to... must provide such an IRS determination letter, which includes their EIN/TIN. Applicants that apply under a group EIN/TIN must be identified by the parent EIN/TIN as a member or sub-unit of the parent EIN...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

7 CFR 3.44 - Centralized administrative offset.

Code of Federal Regulations, 2012 CFR

2012-01-01

... TINs of debtors who owe debts referred to Treasury under this section shall be compared to the names and TINs on payments to be made by Federal disbursing officials. Federal disbursing officials include... and TIN of a debtor match the name and TIN of a payee and all other requirements for offset have been...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

40 CFR 721.10230 - Rutile, tin zinc, calcium doped.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Rutile, tin zinc, calcium doped. 721... Substances § 721.10230 Rutile, tin zinc, calcium doped. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as rutile, tin zinc, calcium-doped (PMN P-06...

40 CFR 721.10231 - Rutile, tin zinc, sodium-doped.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Rutile, tin zinc, sodium-doped. 721... Substances § 721.10231 Rutile, tin zinc, sodium-doped. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as rutile, tin zinc, sodium-doped (PMN P-06-37...

77 FR 34938 - Certain Tin Mill Products From Japan: Continuation of Antidumping Duty Order

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-854] Certain Tin Mill Products... duty order on certain tin mill products from Japan would likely lead to continuation or recurrence of...: Background On August 28, 2000, the Department published the antidumping duty order on certain tin mill...

42 CFR 425.504 - Incorporating reporting requirements related to the Physician Quality Reporting System.

Code of Federal Regulations, 2012 CFR

2012-10-01

... under their ACO participant TIN as a group practice under the Physician Quality Reporting System Group... participant TIN, on behalf of its ACO supplier/provider participants who are eligible professionals, will... Physician Fee Schedule for that TIN. (4) ACO participant TINs and individual ACO providers/suppliers who are...

42 CFR 425.504 - Incorporating reporting requirements related to the Physician Quality Reporting System.

Code of Federal Regulations, 2013 CFR

2013-10-01

... under their ACO participant TIN as a group practice under the Physician Quality Reporting System Group... participant TIN, on behalf of its ACO supplier/provider participants who are eligible professionals, will... Physician Fee Schedule for that TIN. (4) ACO participant TINs and individual ACO providers/suppliers who are...

7 CFR 3.44 - Centralized administrative offset.

Code of Federal Regulations, 2010 CFR

2010-01-01

... TINs of debtors who owe debts referred to Treasury under this section shall be compared to the names and TINs on payments to be made by Federal disbursing officials. Federal disbursing officials include... and TIN of a debtor match the name and TIN of a payee and all other requirements for offset have been...

76 FR 14902 - Certain Tin Mill Products From Japan: Rescission of Antidumping Duty Administrative Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-18

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-854] Certain Tin Mill Products... duty order covering certain tin mill products from Japan. The period of review is August 1, 2009... parties to request an administrative review of the antidumping duty order on certain tin mill products...

7 CFR 3.44 - Centralized administrative offset.

Code of Federal Regulations, 2011 CFR

2011-01-01

... TINs of debtors who owe debts referred to Treasury under this section shall be compared to the names and TINs on payments to be made by Federal disbursing officials. Federal disbursing officials include... and TIN of a debtor match the name and TIN of a payee and all other requirements for offset have been...

40 CFR 721.10231 - Rutile, tin zinc, sodium-doped.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Rutile, tin zinc, sodium-doped. 721... Substances § 721.10231 Rutile, tin zinc, sodium-doped. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as rutile, tin zinc, sodium-doped (PMN P-06-37...

77 FR 5767 - Certain Tin Mill Products From Japan: Rescission of Antidumping Duty Administrative Review

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-854] Certain Tin Mill Products... duty order covering certain tin mill products from Japan. The period of review is August 1, 2010... parties to request an administrative review of the antidumping duty order on certain tin mill products...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

7 CFR 3.44 - Centralized administrative offset.

Code of Federal Regulations, 2013 CFR

2013-01-01

... TINs of debtors who owe debts referred to Treasury under this section shall be compared to the names and TINs on payments to be made by Federal disbursing officials. Federal disbursing officials include... and TIN of a debtor match the name and TIN of a payee and all other requirements for offset have been...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

40 CFR 721.10230 - Rutile, tin zinc, calcium doped.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Rutile, tin zinc, calcium doped. 721... Substances § 721.10230 Rutile, tin zinc, calcium doped. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as rutile, tin zinc, calcium-doped (PMN P-06...

76 FR 68512 - Carolina Power & Light Company; H. B. Robinson Steam Electric Plant, Unit 2; Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... (~1 percent). The elimination of tin has resulted in superior corrosion resistance and reduced irradiation-induced growth relative to both standard zircaloy (1.7 percent tin) and low-tin zircaloy (1.2 percent tin). The addition of niobium increases ductility, which is desirable to avoid brittle failures...

7 CFR 3.44 - Centralized administrative offset.

Code of Federal Regulations, 2014 CFR

2014-01-01

... TINs of debtors who owe debts referred to Treasury under this section shall be compared to the names and TINs on payments to be made by Federal disbursing officials. Federal disbursing officials include... and TIN of a debtor match the name and TIN of a payee and all other requirements for offset have been...

Influence of Microstructure on the Electrical Properties of Heteroepitaxial TiN Films

NASA Astrophysics Data System (ADS)

Xiang, Wenfeng; Liu, Yuan; Zhang, Jiaqi

2018-05-01

Heteroepitaxial TiN films were deposited on Si substrates by pulse laser deposition at different substrate temperature. The microstructure and surface morphology of the films were investigated by X-ray diffraction (θ-2θ scan, ω-scan, and ϕ-scan) and atomic force microscopy. The electrical properties of the prepared TiN films were studied using a physical property measurement system. The experimental results showed that the crystallinity and surface morphology of the TiN films were improved gradually with increasing substrate temperature below 700 °C. Specially, single crystal TiN films were prepared when substrate temperature is above 700 °C; However, the quality of TiN films gradually worsened when the substrate temperature was increased further. The electrical properties of the films were directly correlated to their crystalline quality. At the optimal substrate temperature of 700 °C, the TiN films exhibited the lowest resistivity and highest mobility of 25.7 μΩ cm and 36.1 cm2/V s, respectively. In addition, the mechanism concerning the influence of substrate temperature on the microstructure of TiN films is discussed in detail.

From toothpaste to topological insulators and materials for valleytronics: The journeys of fluorinated tin

NASA Astrophysics Data System (ADS)

Barraza-Lopez, Salvador; Rivero, Pablo; Yan, Jia-An; Garcia-Suarez, Victor Manuel; Ferrer, Jaime

2015-03-01

Tin fluoride has a vast literature. This material is stable in bulk form at room temperature and has commercial applications that include fluorinated toothpaste. Bulk tin fluoride has a pair of fluorine atoms bridging two tin atoms. In the recent past the electronic properties of 2D tin with honeycomb structure have been discussed thus generating a wealth of literature that emphasizes its non-topologically-trivial electronic properties due to the combination of a Dirac-like dispersion and a strong spin-orbit coupling given its large atomic mass. Nevertheless the stability of such freestanding structures has been contested recently. As it turns out, the most stable form of fluorinated tin does not possess a graphane-like structure either. In the most stable phase to be discussed here, fluorine atoms tilt away from (graphane-like) positions over/below tin atoms; in an atomistic arrangement similar to the one seen on their parent bulk structure. Electronic properties depend on atomistic coordination, and the most stable form of fluorinated tin does not possess non-trivial topological properties. Nevertheless it represents a new paradigm for valleytronics in 2D.

Organo-tins in sediments and mussels from the Sado estuarine system (Portugal).

PubMed

Quevauviller, P; Lavigne, R; Pinel, R; Astruc, M

1989-01-01

Analyses of methyl- and butyl-tin levels in freshwater, estuarine and marine sediments from the Sado estuarine system, and in mussels (Mytilus galloprovincialis) from its adjacent coast, have been performed in order to detect the contaminated areas. The main inputs of tributyl-tin (TBT), along with degradation products di- and monobutyl-tin (DBT and MBT), were detected in the estuarine zone, due to high discharge from shipyards located in this area. These levels are sometimes very high, ranging from 235 to 12,200 ng g(-1) total butyl-tins in sediments. Such inputs lead to higher bioconcentration values in mussels in the estuarine zone, as well as in a harbour located along the adjacent coast. The bioconcentration of organo-tins in mussel tissues could be enhanced in estuarine turbid waters, due to an ingestion of butyl-tins adsorbed onto fine particles, in comparison with non-turbid coastal waters. Debutylation processes occur in both sediments and mussel tissues; in organisms, these processes may lead to the formation of inorganic tin, which may be methylated differently according to the period of the year.

Carbon/tin oxide composite electrodes for improved lithium-ion batteries

DOE PAGES

Li, Yunchao; Levine, Alan M.; Zhang, Jinshui; ...

2018-05-17

Tin and tin oxide-based electrodes are promising high-capacity anodes for lithium-ion batteries. However, poor capacity retention is the major issue with these materials due to the large volumetric expansion that occurs when lithium is alloyed with tin during lithiation and delithiation process. Here, a method to prepare a low-cost, scalable carbon and tin(II) oxide composite anode is reported. The composite material was prepared by ball milling of carbon recovered from used tire powders with 25 wt% tin(II) oxide to form lithium-ion battery anode. With the impact of energy from the ball milling, tin oxide powders were uniformly distributed inside themore » pores of waste-tire-derived carbon. During lithiation and delithiation, the carbon matrix can effectively absorb the volume expansion caused by tin, thereby minimizing pulverization and capacity fade of the electrodes. In conclusion, the as-synthesized anode yielded a capacity of 690 mAh g –1 after 300 cycles at a current density of 40 mA g –1 with a stable battery performance.« less

Carbon/tin oxide composite electrodes for improved lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yunchao; Levine, Alan M.; Zhang, Jinshui

Tin and tin oxide-based electrodes are promising high-capacity anodes for lithium-ion batteries. However, poor capacity retention is the major issue with these materials due to the large volumetric expansion that occurs when lithium is alloyed with tin during lithiation and delithiation process. Here, a method to prepare a low-cost, scalable carbon and tin(II) oxide composite anode is reported. The composite material was prepared by ball milling of carbon recovered from used tire powders with 25 wt% tin(II) oxide to form lithium-ion battery anode. With the impact of energy from the ball milling, tin oxide powders were uniformly distributed inside themore » pores of waste-tire-derived carbon. During lithiation and delithiation, the carbon matrix can effectively absorb the volume expansion caused by tin, thereby minimizing pulverization and capacity fade of the electrodes. In conclusion, the as-synthesized anode yielded a capacity of 690 mAh g –1 after 300 cycles at a current density of 40 mA g –1 with a stable battery performance.« less

Pechini process-derived tin oxide and tin oxide-graphite composites for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Zhang, R.; Lee, Jim Y.; Liu, Z. L.

The Pechini process [Ceram. Bull. 68 (1989) 1002] is used to obtain fine tin oxide powders that reduce the specific volume change in Li + insertion and extraction reactions. The suitability of these tin oxides as active materials for negative electrodes in lithium-ion batteries is investigated. From elemental analysis, it is found that the templating polymer network is almost completely obliterated after heating at 500 °C. The best tin oxide does not exhibit extensive crystallization of tin atoms even after 30 cycles of alloying and de-alloying reactions with Li. The structure and the specific capacity of the oxides are dependent on the heat treatment and remnants of the polymeric CH network can impose an unfavorable outcome. A capacity of 600 mAh g -1, which is unchanged for 30 cycles, can be obtained from tin oxide heat treated at 1000 °C. Composites of graphite and SnO 2 are also prepared and exhibit synergistic interactions between graphite and tin oxide which are similar to those reported previously [Electrochem. Solid State Lett. 3 (2000) 167].

Infrared Emissivity of Tin upon Release of a 25 GPa Shock into a LiF Window

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turley, W. D., Holtkamp, D. B., Marshall, B. R., Stevens, G. D., Veeser, L. R.

We measured the emissivity of a tin sample at its interface with a lithium-fluoride window upon release of a 25 GPa shock wave from the tin into the window. Measurements were made over four wavelength bands between 1.2 and 5.4 μm. Thermal emission backgrounds from the tin, glue, and lithium fluoride were successfully removed from the reflectance signals. Emissivity changes for the sample, which was initially nearly specular, were small except for the longest wavelength band, where uncertainties were high because of poor signal-to-noise ratio at that wavelength. A thin glue layer, which bonds the sample to the window, wasmore » found to heat from reverberations of the shock wave between the tin and the lithium fluoride. At approximately 3.4 μm the thermal emission from the glue was large compared to the tin, allowing a good estimate of the glue temperature from the thermal radiance. The glue appears to remain slightly colder than the tin, thereby minimizing heat conduction into or out of the tin immediately after the shock passage.« less

Influence of silicon oxide on the performance of TiN bottom electrode in phase change memory

NASA Astrophysics Data System (ADS)

Gao, Dan; Liu, Bo; Xu, Zhen; Wang, Heng; Xia, Yangyang; Wang, Lei; Zhu, Nanfei; Li, Ying; Zhan, Yipeng; Song, Zhitang; Feng, Songlin

2016-10-01

The stability of TiN which is the preferred bottom electrode contact (BEC) of phase change memory (PCM) due to its low thermal conductivity and suitable electrical conductivity, is very essential to the reliability of PCM devices. In this work, in order to investigate the effect of high aspect ratio process (HARP) SiO2 on the performance of TiN, both TiN/SiO2, TiN/SiN thin films and TiN BEC device structures are analyzed. By combining transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS), we found that the TiN would be oxidized after the deposition of HARP SiO2 and there exist a thin ( 4 nm) oxidation interfacial layer between TiN and SiO2. Electrical measurements were performed on the 1R PCM test-key die with 7 nm and 10 nm BEC-only cells. The statistical initial resistances of BEC have wide distribution and it is confirmed that the non-uniform oxidation of TiN BEC affects the astringency of the resistance of TiN BEC. The experimental results help to optimize the process of TiN BEC, and SiN is recommended as a better choice as the linear layer.

40 CFR 721.4600 - Recovered metal hydroxide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Recovered metal hydroxide. 721.4600... Substances § 721.4600 Recovered metal hydroxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a recovered metal hydroxide (PMN P-91-809...

Polysulfide intercalated layered double hydroxides for metal capture applications

DOEpatents

Kanatzidis, Mercouri G.; Ma, Shulan

2017-04-04

Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

21 CFR 73.1010 - Alumina (dried aluminum hydroxide).

Code of Federal Regulations, 2010 CFR

2010-04-01

... GENERAL LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1010 Alumina (dried aluminum hydroxide). (a) Identity. (1) The color additive alumina (dried aluminum hydroxide) is a white, odorless, tasteless, amorphous powder consisting essentially of aluminum hydroxide (Al2 O3· XH2 O). (2) Color additive...

21 CFR 73.1326 - Chromium hydroxide green.

Code of Federal Regulations, 2010 CFR

2010-04-01

... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide (Cr2O3·XH2O). (2) Color additive mixtures for drug use made with chromium hydroxide green may contain only those...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

21 CFR 184.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... salt or by hydration of reactive grades of magnesium oxide. (b) The ingredient meets the specifications... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Magnesium hydroxide. 184.1428 Section 184.1428... Listing of Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide...

21 CFR 184.1428 - Magnesium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... hydration of reactive grades of magnesium oxide. (b) The ingredient meets the specifications of the Food... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium hydroxide. 184.1428 Section 184.1428 Food... Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide (Mg(OH)2, CAS...

21 CFR 582.1763 - Sodium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Sodium hydroxide. 582.1763 Section 582.1763 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1763 Sodium hydroxide. (a) Product. Sodium hydroxide. (b) Conditions of use. This substance...

21 CFR 582.1763 - Sodium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Sodium hydroxide. 582.1763 Section 582.1763 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1763 Sodium hydroxide. (a) Product. Sodium hydroxide. (b) Conditions of use. This substance...

21 CFR 582.1763 - Sodium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium hydroxide. 582.1763 Section 582.1763 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1763 Sodium hydroxide. (a) Product. Sodium hydroxide. (b) Conditions of use. This substance...

21 CFR 582.1763 - Sodium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Sodium hydroxide. 582.1763 Section 582.1763 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1763 Sodium hydroxide. (a) Product. Sodium hydroxide. (b) Conditions of use. This substance...

21 CFR 582.1763 - Sodium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Sodium hydroxide. 582.1763 Section 582.1763 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1763 Sodium hydroxide. (a) Product. Sodium hydroxide. (b) Conditions of use. This substance...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

Tubulointerstitial nephritis antigen: an extracellular matrix protein that selectively regulates tubulogenesis vs. glomerulogenesis during mammalian renal development.

PubMed

Kanwar, Y S; Kumar, A; Yang, Q; Tian, Y; Wada, J; Kashihara, N; Wallner, E I

1999-09-28

Tubulointerstitial nephritis antigen (TIN-ag) is an extracellular matrix protein and is expressed in the renal tubular basement membranes. Its role in metanephric development was investigated. TIN-ag cDNA, isolated from the newborn mouse library, had an ORF of 1,425 nucleotides, a putative signal sequence, and an ATP/GTP-binding site. The translated sequence had approximately 80% identity with rabbit TIN-ag. Among various tissues, TIN-ag mRNA was primarily expressed in the newborn kidney. In the embryonic metanephros, TIN-ag expression was confined to the distal convolution or pole of the S-shaped body, the segment of the nascent nephron that is the progenitor of renal tubules. Treatment with TIN-ag antisense oligodeoxynucleotide induced dysmorphogenesis of the embryonic metanephroi, malformation of the S-shaped body, and a decrease in the tubular population, whereas the glomeruli were unaffected. Treatment also led to a decrease of TIN-Ag mRNA, de novo synthesis of TIN-ag protein, and its antibody reactivity. The mRNA expression of glomerular epithelial protein 1 (a marker for renal podocytes), anti-heparan-sulfate-proteoglycan antibody reactivity, and wheat germ agglutinin lectin staining of the metanephros were unaffected. The anti-TIN-ag antibody treatment also caused deformation of the S-shaped body and a reduction in the tubular population, whereas the glomeruli were unchanged. The data suggest that the TIN-ag, unlike other basement membrane proteins, selectively regulates tubulogenesis, whereas glomerulogenesis is largely unaffected.

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Lee, Mun Hyung; Park, Joo Hyun

2018-06-01

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When Δ T TiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the `Ostwald ripening model' based on the Lifshitz-Slyozov-Wagner theory in conjunction with the `Diffusion controlled model' using Ohnaka's microsegregation equation.

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Lee, Mun Hyung; Park, Joo Hyun

2018-03-01

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ΔT TiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the `Ostwald ripening model' based on the Lifshitz-Slyozov-Wagner theory in conjunction with the `Diffusion controlled model' using Ohnaka's microsegregation equation.

76 FR 17391 - Applications for New Awards; United States-Brazil Higher Education Consortia Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-29

... Number (TIN); b. Register both your DUNS number and TIN with the Central Contractor Registry (CCR), the Government's primary registrant database; c. Provide your DUNS number and TIN on your application; and d..., agency, institution, or organization, you can obtain a TIN from the Internal Revenue Service. If you are...

19 CFR 159.22 - Net weights and tares.

Code of Federal Regulations, 2013 CFR

2013-04-01

... tins imported from Spain: The following schedule drained weight shall be used as the Customs dutiable... in tins and such drained weight being the allowance made in liquidation for tare for water: Size can Drained weight 3 kilo 13.6 kilograms-case of 6 tins. 794 grams 16.7 kilograms-case of 24 tins. 425 grams 8...

78 FR 22855 - Applications for New Awards; Fulbright-Hays Group Projects Abroad Program-Short-Term Projects

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-17

... (DUNS) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with... (SAM), the Government's primary registrant database; c. Provide your DUNS number and TIN on your... you are a corporate entity, agency, institution, or organization, you can obtain a TIN from the...

76 FR 66855 - United States Savings Bonds, Series EE, HH and I

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-28

.... 351.43 to read as follows: Sec. 351.43 Are Taxpayer Identification Numbers (TINs) required for the... owner's TIN is not known, the TIN of the purchaser must be included in the registration of the bond. 0 6.... 359.28 Are Taxpayer Identification Numbers (TINs) required for the registration of definitive series I...

77 FR 37012 - Applications for New Awards: Disability and Rehabilitation Research Projects and Centers Program...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-20

... Number (TIN); b. Register both your DUNS number and TIN with the Central Contractor Registry (CCR), the Government's primary registrant database; c. Provide your DUNS number and TIN on your application; and d..., agency, institution, or organization, you can obtain a TIN from the Internal Revenue Service. If you are...

77 FR 51782 - Federal Acquisition Regulation; Information Collection; Taxpayer Identification Number Information

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-27

... agency is required to furnish its Tax Identification Number (TIN) to that agency. 31 U.S.C. 3325(d... and submitted to a disbursing official, the TIN of the contractor receiving payment under the voucher... other information, its TIN. The TIN may be used by the Government to collect and report on any...

19 CFR 159.22 - Net weights and tares.

Code of Federal Regulations, 2012 CFR

2012-04-01

... tins imported from Spain: The following schedule drained weight shall be used as the Customs dutiable... in tins and such drained weight being the allowance made in liquidation for tare for water: Size can Drained weight 3 kilo 13.6 kilograms-case of 6 tins. 794 grams 16.7 kilograms-case of 24 tins. 425 grams 8...

78 FR 18343 - Federal Acquisition Regulation; Submission for OMB Review; Taxpayer Identification Number...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-26

... agency is required to furnish its Tax Identification Number (TIN) to that agency. 31 U.S.C. 3325(d... and submitted to a disbursing official, the TIN of the contractor receiving payment under the voucher... other information, its TIN. The TIN may be used by the Government to collect and report on any...

77 FR 11189 - Yokohama Tire Corporation, Denial of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-24

... full Tire Identification Number (TIN) on one sidewall but omit the partial serial number on the other....'' YTC explained its belief that the Tire Identification Number (TIN) and the partial TIN are used to... TIN is molded on the intended outboard sidewall of these tires and consumers could be directed to have...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2014 CFR

2014-04-01

.... 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two molecules of water. It is prepared from...

19 CFR 159.22 - Net weights and tares.

Code of Federal Regulations, 2014 CFR

2014-04-01

... tins imported from Spain: The following schedule drained weight shall be used as the Customs dutiable... in tins and such drained weight being the allowance made in liquidation for tare for water: Size can Drained weight 3 kilo 13.6 kilograms-case of 6 tins. 794 grams 16.7 kilograms-case of 24 tins. 425 grams 8...

75 FR 51524 - Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-20

... noncompliance is that the subject tires do not have full or partial Tire Identification Numbers (TIN) on one of their sidewalls. YTC explained that the intended outboard sidewall did have the complete TIN, but the opposite sidewall has no TIN or partial TIN. YTC stated its belief that the noncompliance is...

76 FR 58536 - Tin- and Chromium-Coated Steel Sheet From Japan; Notice of Commission Determination To Conduct a...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-21

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-860 (Second Review)] Tin- and Chromium... Concerning the Antidumping Duty Order on Tin- and Chromium-Coated Steel Sheet From Japan AGENCY: United.... 1675(c)(5)) to determine whether revocation of the antidumping duty order on tin- and chromium-coated...

19 CFR 159.22 - Net weights and tares.

Code of Federal Regulations, 2010 CFR

2010-04-01

... tins imported from Spain: The following schedule drained weight shall be used as the Customs dutiable... in tins and such drained weight being the allowance made in liquidation for tare for water: Size can Drained weight 3 kilo 13.6 kilograms-case of 6 tins. 794 grams 16.7 kilograms-case of 24 tins. 425 grams 8...

19 CFR 159.22 - Net weights and tares.

Code of Federal Regulations, 2011 CFR

2011-04-01

... tins imported from Spain: The following schedule drained weight shall be used as the Customs dutiable... in tins and such drained weight being the allowance made in liquidation for tare for water: Size can Drained weight 3 kilo 13.6 kilograms-case of 6 tins. 794 grams 16.7 kilograms-case of 24 tins. 425 grams 8...

77 FR 42990 - Significant New Use Rules on Certain Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... Toxic Substances Control Act (TSCA) for the chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (CAS No. 389623-07-8) which were the subject of..., tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (PMN P...

Effect of alloying elements on the physicomechanical properties of copper and tin bronze

NASA Astrophysics Data System (ADS)

Ri, Kh.; Komkov, V. G.; Ri, E. Kh.

2014-09-01

The effect of alloying elements (Al, Si, Mn, Zn, Ni, As) on the physicomechanical properties of copper and tin bronze (6 wt % Sn) is studied. These alloying elements are found to increase the hardness and the microhardness of the structural constituents of Cu- X alloys due to hardening the α solid solution and eutectoid, and this effect of alloying elements is most effective in tin bronze. Alloyed copper and tin bronze have a lower thermal conductivity and corrosion resistance as compared to plain copper and tin bronze.

Stannosis in Hearth Tinners

PubMed Central

Cole, C. W. D.; Davies, J. V. S. A.; Kipling, M. D.; Ritchie, G. L.

1964-01-01

There have been no published reports of stannosis in tinners. In this paper its occurrence in hearth tinners is described. In hearth tinning molten tin is poured into heated iron hollow-ware and smoothed over the internal surface with a cork bat. Ammonium chloride powder is used as a flux. It is considered that fumes arising in the process from the reaction of the flux and the tin caused a concentration of tin compounds in the atmosphere, and this was the mechanism by which stannosis was produced. The literature on stannosis and tinning is reviewed. Images PMID:14180484

VO2 /TiN Plasmonic Thermochromic Smart Coatings for Room-Temperature Applications.

PubMed

Hao, Qi; Li, Wan; Xu, Huiyan; Wang, Jiawei; Yin, Yin; Wang, Huaiyu; Ma, Libo; Ma, Fei; Jiang, Xuchuan; Schmidt, Oliver G; Chu, Paul K

2018-03-01

Vanadium dioxide/titanium nitride (VO 2 /TiN) smart coatings are prepared by hybridizing thermochromic VO 2 with plasmonic TiN nanoparticles. The VO 2 /TiN coatings can control infrared (IR) radiation dynamically in accordance with the ambient temperature and illumination intensity. It blocks IR light under strong illumination at 28 °C but is IR transparent under weak irradiation conditions or at a low temperature of 20 °C. The VO 2 /TiN coatings exhibit a good integral visible transmittance of up to 51% and excellent IR switching efficiency of 48% at 2000 nm. These unique advantages make VO 2 /TiN promising as smart energy-saving windows. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Molten tin reprocessing of spent nuclear fuel elements

DOEpatents

Heckman, Richard A.

1983-01-01

A method and apparatus for reprocessing spent nuclear fuel is described. Within a containment vessel, a solid plug of tin and nitride precipitates supports a circulating bath of liquid tin therein. Spent nuclear fuel is immersed in the liquid tin under an atmosphere of nitrogen, resulting in the formation of nitride precipitates. The layer of liquid tin and nitride precipitates which interfaces the plug is solidified and integrated with the plug. Part of the plug is melted, removing nitride precipitates from the containment vessel, while a portion of the plug remains solidified to support the liquid tin and nitride precipitates remaining in the containment vessel. The process is practiced numerous times until substantially all of the precipitated nitrides are removed from the containment vessel.

Antimicrobial Activity of Calcium Hydroxide in Endodontics: A Review

PubMed Central

Shalavi, S; Yazdizadeh, M

2012-01-01

The purpose of endodontic therapy is to preserve the patient's natural teeth without compromising the patient's local or systemic health. Calcium hydroxide has been included in several materials and antimicrobial formulations that are used in several treatment modalities in endodontics, such as inter-appointment intracanal medicaments. The purpose of this article was to review the antimicrobial properties of calcium hydroxide in endodontics. Calcium hydroxide has a high pH (approximately 12.5-12.8) and is classified chemically as a strong base. The lethal effects of calcium hydroxide on bacterial cells are probably due to protein denaturation and damage to DNA and cytoplasmic membranes. Calcium hydroxide has a wide range of antimicrobial activity against common endodontic pathogens but is less effective against Enterococcus faecalis and Candida albicans. Calcium hydroxide is also a valuable anti-endotoxin agent. However, its effect on microbial biofilms is controversial. PMID:23323217

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

21 CFR 73.1326 - Chromium hydroxide green.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Chromium hydroxide green. 73.1326 Section 73.1326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide (Cr2O3·XH2O...

Ytterbium coating of spherical Ni(OH) 2 cathode materials for Ni-MH batteries at elevated temperature

NASA Astrophysics Data System (ADS)

He, Xiangming; Wang, Li; Li, Wen; Jiang, Changyin; Wan, Chunrong

The Yb/Co coated nickel hydroxides were prepared by precipitation of Yb(OH) 3 on the surface of spherical nickel hydroxide, followed by precipitation of Co(OH) 2 on its surface. The optimum coating content of ytterbium was around 2% (atomic concentration) to obtain high discharge capacity at 60 °C. It was shown that the discharge capacity of nickel hydroxide at high temperatures was improved by coating of ytterbium and cobalt hydroxide. The high temperature performances of the sealed AAA-sized Ni-MH batteries using Yb/Co coated nickel hydroxide as positive electrodes were carried out, showing much better than those using the un-coated and only Co(OH) 2 coated nickel hydroxide electrodes. The charge acceptance of the battery using 2% Yb and 2% Co coated nickel hydroxide reached 92% at 60 °C, where the charge acceptances for the un-coated and only cobalt coated ones were only 42 and 46%, respectively. It has shown that the Yb/Co coating is an effective way to improve the high temperature performance of nickel hydroxide for nickel-metal hydride batteries.

Comparison of phenol and sodium hydroxide chemical matricectomies for the treatment of ingrowing toenails.

PubMed

Bostanci, Seher; Kocyigit, Pelin; Gürgey, Erbak

2007-06-01

Chemical matricectomy is performed mainly by two agents: phenol and sodium hydroxide. Both agents have excellent cure rates, but there are no data about the comparison of postoperative healing periods. This study was designed to compare the postoperative morbidity rates of sodium hydroxide and phenol matricectomies. Forty-six patients with 154 ingrowing nail sides were treated with either sodium hydroxide or phenol matricectomy. In the postoperative period, the patients were evaluated for the duration and severity of pain, drainage, and peripheral tissue destruction; complete healing periods; and overall success rates. The incidence of pain was higher in the sodium hydroxide group on the first visit, on the second day, but all patients became pain-free after that. The incidence and duration of drainage and peripheral tissue destruction was significantly higher in the phenol group. The mean period for complete recovery was 10.8 days in the sodium hydroxide group, whereas it was 18.02 days in the phenol group. The overall success rates in the sodium hydroxide and phenol groups were found to be 95.1 and 95.8%, respectively. Both sodium hydroxide and phenol are effective agents giving high success rates, but sodium hydroxide causes less postoperative morbidity and provides faster recovery.

Antimicrobial activity of calcium hydroxide and chlorhexidine on intratubular Candida albicans

PubMed Central

Jacques Rezende Delgado, Ronan; Helena Gasparoto, Thaís; Renata Sipert, Carla; Ramos Pinheiro, Claudia; Gomes de Moraes, Ivaldo; Brandão Garcia, Roberto; Antônio Hungaro Duarte, Marco; Monteiro Bramante, Clóvis; Aparecido Torres, Sérgio; Pompermaier Garlet, Gustavo; Paula Campanelli, Ana; Bernardineli, Norberti

2013-01-01

This study investigated the efficacy of calcium hydroxide and chlorhexidine gel for the elimination of intratubular Candida albicans (C. albicans). Human single-rooted teeth contaminated with C. albicans were treated with calcium hydroxide, 2% chlorhexidine gel, calcium hydroxide plus 2% chlorhexidine gel, or saline (0.9% sodium chloride) as a positive control. The samples obtained at depths of 0–100 and 100–200 µm from the root canal system were analyzed for C. albicans load by counting the number of colony forming units and for the percentage of viable C. albicans using fluorescence microscopy. First, the antimicrobial activity of calcium hydroxide and the 2% chlorhexidine gel was evaluated by counting the number of colony forming units. After 14 days of intracanal medication, there was a significant decrease in the number of C. albicans colony forming units at a depth of 0–100 µm with chlorhexidine treatment either with or without calcium hydroxide compared with the calcium hydroxide only treatment. However, there were no differences in the number of colony forming units at the 100–200 µm depth for any of the medications investigated. C. albicans viability was also evaluated by vital staining techniques and fluorescence microscopy analysis. Antifungal activity against C. albicans significantly increased at both depths in the chlorhexidine groups with and without calcium hydroxide compared with the groups treated with calcium hydroxide only. Treatments with only chlorhexidine or chlorhexidine in combination with calcium hydroxide were effective for elimination of C. albicans. PMID:23538639

Evaluation of calcium ion, hydroxyl ion release and pH levels in various calcium hydroxide based intracanal medicaments: An in vitro study

PubMed Central

Fulzele, Punit; Baliga, Sudhindra; Thosar, Nilima; Pradhan, Debaprya

2011-01-01

Aims: Evaluation of calcium ion and hydroxyl ion release and pH levels in various calcium hydroxide based intracanal medicaments. Objective: The purpose of this study was to evaluate calcium and hydroxyl ion release and pH levels of calcium hydroxide based products, namely, RC Cal, Metapex, calcium hydroxide with distilled water, along with the new gutta-percha points with calcium hydroxide. Materials and Methods: The materials were inserted in polyethylene tubes and immersed in deionized water. The pH variation, Ca++ and OH- release were monitored periodically for 1 week. Statistical Analysis Used: Statistical analysis was carried out using one-way analysis of variance and Tukey's post hoc tests with PASW Statistics version 18 software to compare the statistical difference. Results: After 1 week, calcium hydroxide with distilled water and RC Cal raised the pH to 12.7 and 11.8, respectively, while a small change was observed for Metapex, calcium hydroxide gutta-percha points. The calcium released after 1 week was 15.36 mg/dL from RC Cal, followed by 13.04, 1.296, 3.064 mg/dL from calcium hydroxide with sterile water, Metapex and calcium hydroxide gutta-percha points, respectively. Conclusions: Calcium hydroxide with sterile water and RC Cal pastes liberate significantly more calcium and hydroxyl ions and raise the pH higher than Metapex and calcium hydroxidegutta-percha points. PMID:22346155

Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim J.; Asfour, Shihab S.; Onar, Arzu; Bayliss, Jon A.; Ludwig, Larry L.; Wright, Maria C.

2010-01-01

To comply with lead-free legislation, many manufacturers have converted from tin-lead to pure tin finishes of electronic components. However, pure tin finishes have a greater propensity to grow tin whiskers than tin-lead finishes. Since tin whiskers present an electrical short circuit hazard in electronic components, simulations have been developed to quantify the risk of said short circuits occurring. Existing risk simulations make the assumption that when a free tin whisker has bridged two adjacent exposed electrical conductors, the result is an electrical short circuit. This conservative assumption is made because shorting is a random event that had an unknown probability associated with it. Note however that due to contact resistance electrical shorts may not occur at lower voltage levels. In our first article we developed an empirical probability model for tin whisker shorting. In this paper, we develop a more comprehensive empirical model using a refined experiment with a larger sample size, in which we studied the effect of varying voltage on the breakdown of the contact resistance which leads to a short circuit. From the resulting data we estimated the probability distribution of an electrical short, as a function of voltage. In addition, the unexpected polycrystalline structure seen in the focused ion beam (FIB) cross section in the first experiment was confirmed in this experiment using transmission electron microscopy (TEM). The FIB was also used to cross section two card guides to facilitate the measurement of the grain size of each card guide's tin plating to determine its finish .

Developing an Empirical Model for Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim J.; Asfour, Shihab S.; Onar, Arzu; Bayliss, Jon A.; Ludwig, Larry L.; Wright, Maria C.

2009-01-01

To comply with lead-free legislation, many manufacturers have converted from tin-lead to pure tin finishes of electronic components. However, pure tin finishes have a greater propensity to grow tin whiskers than tin-lead finishes. Since tin whiskers present an electrical short circuit hazard in electronic components, simulations have been developed to quantify the risk of said short circuits occurring. Existing risk simulations make the assumption that when a free tin whisker has bridged two adjacent exposed electrical conductors, the result is an electrical short circuit. This conservative assumption is made because shorting is a random event that had an unknown probability associated with it. Note however that due to contact resistance electrical shorts may not occur at lower voltage levels. In our first article we developed an empirical probability model for tin whisker shorting. In this paper, we develop a more comprehensive empirical model using a refined experiment with a larger sample size, in which we studied the effect of varying voltage on the breakdown of the contact resistance which leads to a short circuit. From the resulting data we estimated the probability distribution of an electrical short, as a function of voltage. In addition, the unexpected polycrystalline structure seen in the focused ion beam (FIB) cross section in the first experiment was confirmed in this experiment using transmission electron microscopy (TEM). The FIB was also used to cross section two card guides to facilitate the measurement of the grain size of each card guide's tin plating to determine its finish.

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2010 CFR

2010-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-0969-091) is the chloride salt of metallic tin that contains two...

21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Tin-coated lead foil capsules for wine bottles... Substances Prohibited From Indirect Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one...

21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tin-coated lead foil capsules for wine bottles. 189... Substances Prohibited From Indirect Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one...

21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Tin-coated lead foil capsules for wine bottles... Substances Prohibited From Indirect Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one...

31 CFR 256.13 - Are agencies required to supply a taxpayer identification number (TIN) when submitting a request...

Code of Federal Regulations, 2011 CFR

2011-07-01

... taxpayer identification number (TIN) when submitting a request for payment? 256.13 Section 256.13 Money and... BILLS Requesting Payments § 256.13 Are agencies required to supply a taxpayer identification number (TIN) when submitting a request for payment? Yes, agencies must include a valid TIN on all requests for...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two...

31 CFR 359.53 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series I...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (TINs) required for registration of book-entry Series I savings bonds? 359.53 Section 359.53 Money and... Savings Bonds § 359.53 Are taxpayer identification numbers (TINs) required for registration of book-entry Series I savings bonds? The TIN of each person named in the registration is required to purchase a book...

31 CFR 351.68 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (TINs) required for registration of book-entry Series EE savings bonds? 351.68 Section 351.68 Money and... Savings Bonds § 351.68 Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE savings bonds? The TIN of each person named in the registration is required to purchase a book...

76 FR 60001 - Certain Tin Mill Products From Japan; Final Results of the Second Expedited Sunset Review of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-28

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-854] Certain Tin Mill Products... duty order on certain tin mill products from Japan, pursuant to section 751(c) of the Tariff [[Page... on certain tin mill products from Japan pursuant to section 751(c) of the Act. See Initiation of Five...

31 CFR 256.13 - Are agencies required to supply a taxpayer identification number (TIN) when submitting a request...

Code of Federal Regulations, 2010 CFR

2010-07-01

... taxpayer identification number (TIN) when submitting a request for payment? 256.13 Section 256.13 Money and... BILLS Requesting Payments § 256.13 Are agencies required to supply a taxpayer identification number (TIN) when submitting a request for payment? Yes, agencies must include a valid TIN on all requests for...

31 CFR 359.53 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series I...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (TINs) required for registration of book-entry Series I savings bonds? 359.53 Section 359.53 Money and... Savings Bonds § 359.53 Are taxpayer identification numbers (TINs) required for registration of book-entry Series I savings bonds? The TIN of each person named in the registration is required to purchase a book...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-0969-091) is the chloride salt of metallic tin that contains two...

31 CFR 256.13 - Are agencies required to supply a taxpayer identification number (TIN) when submitting a request...

Code of Federal Regulations, 2012 CFR

2012-07-01

... taxpayer identification number (TIN) when submitting a request for payment? 256.13 Section 256.13 Money and... BILLS Requesting Payments § 256.13 Are agencies required to supply a taxpayer identification number (TIN) when submitting a request for payment? Yes, agencies must include a valid TIN on all requests for...

31 CFR 351.68 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (TINs) required for registration of book-entry Series EE savings bonds? 351.68 Section 351.68 Money and... EE Savings Bonds § 351.68 Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE savings bonds? The TIN of each person named in the registration is required to...

31 CFR 359.53 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series I...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (TINs) required for registration of book-entry Series I savings bonds? 359.53 Section 359.53 Money and... Savings Bonds § 359.53 Are taxpayer identification numbers (TINs) required for registration of book-entry Series I savings bonds? The TIN of each person named in the registration is required to purchase a book...

31 CFR 256.13 - Are agencies required to supply a taxpayer identification number (TIN) when submitting a request...

Code of Federal Regulations, 2014 CFR

2014-07-01

... taxpayer identification number (TIN) when submitting a request for payment? 256.13 Section 256.13 Money and... BILLS Requesting Payments § 256.13 Are agencies required to supply a taxpayer identification number (TIN) when submitting a request for payment? Yes, agencies must include a valid TIN on all requests for...

21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Tin-coated lead foil capsules for wine bottles... Substances Prohibited From Indirect Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one...

31 CFR 351.68 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (TINs) required for registration of book-entry Series EE savings bonds? 351.68 Section 351.68 Money and... Savings Bonds § 351.68 Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE savings bonds? The TIN of each person named in the registration is required to purchase a book...

78 FR 34355 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-07

... (TIN); b. Register both your DUNS number and TIN with the Central Contractor Registry (CCR)--and, after...; c. Provide your DUNS number and TIN on your application; and d. Maintain an active CRR or SAM... organization, you can obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain...

31 CFR 359.53 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series I...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (TINs) required for registration of book-entry Series I savings bonds? 359.53 Section 359.53 Money and... Savings Bonds § 359.53 Are taxpayer identification numbers (TINs) required for registration of book-entry Series I savings bonds? The TIN of each person named in the registration is required to purchase a book...

31 CFR 351.68 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (TINs) required for registration of book-entry Series EE savings bonds? 351.68 Section 351.68 Money and... Savings Bonds § 351.68 Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE savings bonds? The TIN of each person named in the registration is required to purchase a book...

31 CFR 359.53 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series I...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (TINs) required for registration of book-entry Series I savings bonds? 359.53 Section 359.53 Money and... Savings Bonds § 359.53 Are taxpayer identification numbers (TINs) required for registration of book-entry Series I savings bonds? The TIN of each person named in the registration is required to purchase a book...

31 CFR 256.13 - Are agencies required to supply a taxpayer identification number (TIN) when submitting a request...

Code of Federal Regulations, 2013 CFR

2013-07-01

... taxpayer identification number (TIN) when submitting a request for payment? 256.13 Section 256.13 Money and... BILLS Requesting Payments § 256.13 Are agencies required to supply a taxpayer identification number (TIN) when submitting a request for payment? Yes, agencies must include a valid TIN on all requests for...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2012 CFR

2012-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two...

Tin Whisker Testing and Modeling

DTIC Science & Technology

2015-11-01

FINAL REPORT Tin Whisker Testing and Modeling SERDP Project WP-1753 NOVEMBER 2015 Stephan J. Meschter Polina Snugovsky BAE Systems...lead (Pb) is that component manufacturers have primarily switched to tin -rich finishes and solder alloys in commercial-off-the-shelf products...Unfortunately, this creates an increased risk of tin whisker formation that can result in undesirable electrical failures unless military and aerospace

31 CFR 351.68 - Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (TINs) required for registration of book-entry Series EE savings bonds? 351.68 Section 351.68 Money and... Savings Bonds § 351.68 Are taxpayer identification numbers (TINs) required for registration of book-entry Series EE savings bonds? The TIN of each person named in the registration is required to purchase a book...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide. The isooctyl radical in the mercaptoacetate is derived from...

Synthesis of tin (II) oxide from tin (II) oxohydroxide

NASA Astrophysics Data System (ADS)

Kuznetsova, Svetlana; Lisitsa, Konstantin

2017-11-01

Sufficiently limited use of tin (II) oxide is associated with the difficulties of its preparation without impurities of tin (IV) oxide. Understanding the cause of the oxidation process will make it possible to develop methods for obtaining SnO without impurities. The influence of ammonium chloride concentration in the suspension on the oxide composition was investigated. The temperature of oxidation (400 °C) on the air and temperature decomposition in the argon (350 °C) of Sn6O4(OH)4 in the solid phase were determined by the thermal analysis method. The decomposition temperature of the oxyhydroxide in the suspension of ammonium chloride does not exceed 100 °C. An increase in the content of ammonium chloride in an aqueous solution leads to an increase i n the solubility of oxohydroxide and leads to an increase in pH. The suspensions of Sn6O4(OH)4 were subjected to heat treatment on a sand bath and under microwave irradiation. Samples of tin oxide were obtained. The quantitative composition of the mixture of tin oxides was determined. The research also highlights emphasizes that the oxidation of tin (II) to tin (IV) is associated with the dissolved oxygen content in the suspension.

Wear of tin coating and Al-Si alloy substrate against carburized steel under mixed lubrication

NASA Astrophysics Data System (ADS)

Wang, Q.; Cheng, H. S.; Fine, M. E.

1994-04-01

Tin coatings on Al-Si alloys are widely used in the automotive industries. The soft tin coating and the harder substrate alloy form a tribological system with the advantages of low friction and reasonably high load-bearing capacity. Wear tests of tin coated Al-Si Z332 alloy in conformal contact against carburized 1016 steel have been carried out under mixed lubrications with SAE 10W30 oil to study the wear mechanisms. Two major wear mechanisms, uniform wear of the tin coating due to micro-plowing and spall pitting related to the substrate are found to contribute to the bearing material loss when the fluid lubrication film is relatively thick (Lambda about 1.6). Under conditions of thinner films (Lambda approximately = 0.8), some local coating debonding occurs. The pitting and local coating debounding are closely related to fracture in the substrate. The bonding between silicon and tin seems to be weaker than between aluminum and tin. During wear, oxidation occurs.

Fabrication of TiN nanorods by electrospinning and their electrochemical properties

NASA Astrophysics Data System (ADS)

Sun, Dongfei; Lang, Junwei; Yan, Xingbin; Hu, Litian; Xue, Qunji

2011-05-01

TiN nanorods were synthesized using electrospinning technique followed by thermolysis in different atmospheres. A dimethyl formamide-ethanol solution of poly-(vinyl pyrrolidone) and Ti (IV)-isopropoxide was used as the electrospinning precursor solution and as-spun nanofibers were calcined at 500 °C in air to generate TiO 2 nanofibers. Subsequently, a conversion from TiO 2 nanofibers to TiN nanorods was employed by the nitridation treatment at 600˜1400 °C in ammonia atmosphere. A typical characteristic of the final products was that the pristine nanofibers were cut into nanorods. The conversion from TiO 2 to TiN was realized when the nitridation temperature was above 800 °C. As-prepared nanorods were composed of TiN nano-crystallites and the average crystallite size gradually increased with the increase of the nitridation temperature. Electrochemical properties of TiN nanorods showed strong dependence on the nitridation temperature. The maximum value of the specific capacitance was obtained from the TiN nanorods prepared at 800 °C.

Effect of doping of tin on optoelectronic properties of indium oxide: DFT study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tripathi, Madhvendra Nath, E-mail: ommadhav27@gmail.com

2015-06-24

Indium tin oxide is widely used transparent conductor. Experimentally observed that 6% tin doping in indium oxide is suitable for optoelectronic applications and more doping beyond this limit degrades the optoelectronic property. The stoichiometry (In{sub 32-x}Sn{sub x}O{sub 48+x/2}; x=0-6) is taken to understand the change in lattice parameter, electronic structure, and optical property of ITO. It is observed that lattice parameter increases and becomes constant after 6% tin doping that is in good agreement of the experimental observation. The electronic structure calculation shows that the high tin doping in indium oxide adversely affects the dispersive nature of the bottom ofmore » conduction band of pure indium oxide and decreases the carrier mobility. Optical calculations show that transmittance goes down upto 60% for the tin concentration more than 6%. The present paper shows that how more than 6% tin doping in indium oxide adversely affects the optoelectronic property of ITO.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rohwer, Lauren E. S.; Martin, James E.

In this study, reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results formore » several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF 2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.« less

21 CFR 184.1205 - Calcium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Calcium hydroxide. 184.1205 Section 184.1205 Food... Specific Substances Affirmed as GRAS § 184.1205 Calcium hydroxide. (a) Calcium hydroxide (Ca(OH)2, CAS Reg. No. 1305-62-0) is also known as slaked lime or calcium hydrate. It is produced by the hydration of...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The empirical formula is NaOH. Sodium...

21 CFR 184.1205 - Calcium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium hydroxide. 184.1205 Section 184.1205 Food... GRAS § 184.1205 Calcium hydroxide. (a) Calcium hydroxide (Ca(OH)2, CAS Reg. No. 1305-62-0) is also known as slaked lime or calcium hydrate. It is produced by the hydration of lime. (b) The ingredient...

The alpha-form of the hydroxides of bivalent metals

NASA Technical Reports Server (NTRS)

Feitknecht, W.

1984-01-01

X-ray analyses were made of the hydroxides of the bivalent metals. The freshly pptd. hydroxide is usually in the alpha-form, which on standing is converted to another form or other forms. The alpha and c grating dimensions of the alpha-form and the C6-type of Co, Zn, C, Co-Zn and Ni-Zn hydroxides are tabulated. Ni hydroxide does not exhibit an alpha-form. The alpha-Co(OH)2, the blue form, is stabilized by sugar or by the higher alcohols: these compounds do not stabilize alpha-Zn(OH)2.

Amorphous tin-cadmium oxide films and the production thereof

DOEpatents

Li, Xiaonan; Gessert, Timothy A

2013-10-29

A tin-cadmium oxide film having an amorphous structure and a ratio of tin atoms to cadmium atoms of between 1:1 and 3:1. The tin-cadmium oxide film may have an optical band gap of between 2.7 eV and 3.35 eV. The film may also have a charge carrier concentration of between 1.times.10.sup.20 cm.sup.-3 and 2.times.10.sup.20 cm.sup.-3. The tin cadmium oxide film may also exhibit a Hall mobility of between 40 cm.sup.2V.sup.-1 s.sup.-1 and 60 cm.sup.2V.sup.-1 s.sup.-1. Also disclosed is a method of producing an amorphous tin-cadmium oxide film as described and devices using same.

Nucleation and growth of tin whiskers

NASA Astrophysics Data System (ADS)

Cheng, Jing; Vianco, Paul T.; Zhang, Bei; Li, James C. M.

2011-06-01

Pure tin film of one micron thick was evaporated onto a silicon substrate with chromium and nickel underlayers. The tinned silicon disk was bent by applying a dead load at the center and supported below around the edge to apply biaxial compressive stresses to the tin layer. After 180 C vacuum annealing for 1,2,4,6, and 8 weeks, tin whiskers/hillocks grew. A quantitative method revealed that the overall growth rate decreased with time with a tendency for saturation. A review of the literature showed in general, tin whisker growth has a nucleation period, a growth period and a period of saturation, very similar to recrystallization or phase transformation. In fact we found our data fit Avrami equation very well. This equation shows that the nucleation period was the first week.

Molten tin reprocessing of spent nuclear fuel elements. [Patent application; continuous process

DOEpatents

Heckman, R.A.

1980-12-19

A method and apparatus for reprocessing spent nuclear fuel is described. Within a containment vessel, a solid plug of tin and nitride precipitates supports a circulating bath of liquid tin therein. Spent nuclear fuel is immersed in the liquid tin under an atmosphere of nitrogen, resulting in the formation of nitride precipitates. The layer of liquid tin and nitride precipitates which interfaces the plug is solidified and integrated with the plug. Part of the plug is melted, removing nitride precipitates from the containment vessel, while a portion of the plug remains solidified to support te liquid tin and nitride precipitates remaining in the containment vessel. The process is practiced numerous times until substantially all of the precipitated nitrides are removed from the containment vessel.

Ammonium hydroxide poisoning

MedlinePlus

Ammonium hydroxide is a colorless liquid chemical solution. It is in a class of substances called caustics. Ammonium hydroxide forms when ammonia dissolves in water. This article discusses poisoning from ...

Resonance of an unshared electron pair between two atoms connected by a single bond

PubMed Central

Pauling, Linus

1983-01-01

The reported structure of the dimer of a compound of bicovalent tin indicates that the tin-tin bond is of a new type. It can be described as involving resonance between two structures in which there is transfer of an electron pair from one tin atom to the other. The tin atoms are connected by a single covalent bond (each also forms two covalent bonds with carbon atoms), and an unshared electron pair resonates between the fourth sp3 orbitals of the two atoms. Similar structures probably occur in digermene and distannene. PMID:16593329

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2010 CFR

2010-10-01

... and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN... deems appropriate for its business operations. Each subsidiary with a different TIN must obtain a...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2011 CFR

2011-10-01

... and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN... deems appropriate for its business operations. Each subsidiary with a different TIN must obtain a...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

NASA Goddard Space Flight Center Tin Whisker (and Other Metal Whisker) Homepage

NASA Technical Reports Server (NTRS)

Brusse, Jay; Sampson, Mike; Leidecker, Henning; Kadesch, Jong

2004-01-01

This website provides information about tin whiskers and related research. The independent research performed during the past 50+ years is so vast that it is impractical to cover all aspects of tin whiskers in this one resource. Therefore, the absence of information in this website about a particular aspect of tin whiskers should NOT be construed as evidence of absence.

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

31 CFR 359.28 - Are taxpayer identification numbers (TINs) required for the registration of definitive Series I...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (TINs) required for the registration of definitive Series I savings bonds? 359.28 Section 359.28 Money... Definitive Series I Savings Bonds § 359.28 Are taxpayer identification numbers (TINs) required for the... include the TIN of the owner or first-named coowner. If the bond was purchased as a gift or award and the...

31 CFR 359.28 - Are taxpayer identification numbers (TINs) required for the registration of definitive Series I...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (TINs) required for the registration of definitive Series I savings bonds? 359.28 Section 359.28 Money... Definitive Series I Savings Bonds § 359.28 Are taxpayer identification numbers (TINs) required for the... include the TIN of the owner or first-named coowner. If the bond is being purchased as a gift or award and...

31 CFR 359.28 - Are taxpayer identification numbers (TINs) required for the registration of definitive Series I...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (TINs) required for the registration of definitive Series I savings bonds? 359.28 Section 359.28 Money... Definitive Series I Savings Bonds § 359.28 Are taxpayer identification numbers (TINs) required for the... include the TIN of the owner or first-named coowner. If the bond was purchased as a gift or award and the...

31 CFR 359.28 - Are taxpayer identification numbers (TINs) required for the registration of definitive Series I...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (TINs) required for the registration of definitive Series I savings bonds? 359.28 Section 359.28 Money... Definitive Series I Savings Bonds § 359.28 Are taxpayer identification numbers (TINs) required for the... include the TIN of the owner or first-named coowner. If the bond is being purchased as a gift or award and...

21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Tin-coated lead foil capsules for wine bottles... Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one or both sides with a thin layer...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

76 FR 75794 - Significant New Use Rules on Certain Chemical Substances; Withdrawal of Two Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

...) for chemical substances which were the subject of premanufacture notices (PMNs), i.e., rutile, tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (PMN P-06-37... rutile, tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped...

31 CFR 359.28 - Are taxpayer identification numbers (TINs) required for the registration of definitive Series I...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (TINs) required for the registration of definitive Series I savings bonds? 359.28 Section 359.28 Money... Definitive Series I Savings Bonds § 359.28 Are taxpayer identification numbers (TINs) required for the... include the TIN of the owner or first-named coowner. If the bond was purchased as a gift or award and the...

Shielding properties of lead-free protective clothing and their impact on radiation doses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schlattl, Helmut; Zankl, Maria; Eder, Heinrich

2007-11-15

The shielding properties of two different lead-free materials--tin and a compound of 80% tin and 20% bismuth--for protective clothing are compared with those of lead for three typical x-ray spectra generated at tube voltages of 60, 75, and 120 kV. Three different quantities were used to compare the shielding capability of the different materials: (1) Air-kerma attenuation factors in narrow-beam geometry, (2) air-kerma attenuation factors in broad-beam geometry, and (3) ratios of organ and effective doses in the human body for a whole-body irradiation with a parallel beam directed frontally at the body. The thicknesses of tin (0.45 mm) andmore » the tin/bismuth compound (0.41 mm) to be compared against lead correspond to a lead equivalence value of 0.35 mm for the 75 kV spectrum. The narrow-beam attenuation factors for 0.45 mm tin are 54% and 32% lower than those for 0.35 mm lead for 60 and 120 kV; those for 0.41 mm tin/bismuth are 12% and 32% lower, respectively. The decrease of the broad-beam air-kerma attenuation factors compared to lead is 74%, 46%, and 41% for tin and 42%, 26%, and 33% for tin/bismuth and the spectra at 60, 75, and 120 kV, respectively. Therefore, it is recommended that the characterization of the shielding potential of a material should be done by measurements in broad-beam geometry. Since the secondary radiation that is mainly responsible for the shielding reduction in broad-beam geometry is of low penetrability, only more superficially located organs receive significantly enhanced doses. The increase for the dose to the glandular breast tissue (female) compared to being shielded by lead is 143%, 37%, and 45% when shielded by tin, and 35%, 15%, and 39% when shielded by tin/bismuth for 60, 75, and 120 kV, respectively. The effective dose rises by 60%, 6%, and 38% for tin, and 14%, 3% and, 35% for tin/bismuth shielding, respectively.« less

Cobalt oxide acicular nanorods with high sensitivity for the non-enzymatic detection of glucose.

PubMed

Kung, Chung-Wei; Lin, Chia-Yu; Lai, Yi-Hsuan; Vittal, R; Ho, Kuo-Chuan

2011-09-15

Acicular cobalt oxide nanorods (CoONRs) were prepared for the non-enzymatic detection of glucose, first by directly growing layered cobalt carbonate hydroxide (LCCH) on a conducting fluorine-doped tin oxide (FTO) substrate using a simple chemical bath deposition (CBD) technique and then by transforming the LCCH into CoONRs through pyrolysis. The composition and grain size of the films of LCCH and CoONRs were verified by X-ray diffraction (XRD); their morphologies were examined by scanning electron microscopic (SEM) and transmission electron microscopic (TEM) images. CoONRs showed high electrocatalytic activity for the electro-oxidation of glucose in alkaline media, and the activity was strongly influenced by NaOH concentration, annealing temperature of CoONRs, and thickness of CoONRs film. The pertinent sensor could be successfully used for the quantification of glucose by amperometric method. The sensing parameters include wide linear range up to 3.5 mM, a high sensitivity of 571.8 μA/(cm(2) mM), and a remarkable low detection limit of 0.058 μM. The CoONRs modified electrode exhibited a high selectivity for glucose in human serum, against ascorbic acid, uric acid, and acetaminophen. Copyright © 2011 Elsevier B.V. All rights reserved.

DOUBLE SHELL TANK (DST) HYDROXIDE DEPLETION MODEL FOR CARBON DIOXIDE ABSORPTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

OGDEN DM; KIRCH NW

2007-10-31

This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed.

Tinned Fruit Consumption and Mortality in Three Prospective Cohorts

PubMed Central

Aasheim, Erlend T.; Sharp, Stephen J.; Appleby, Paul N.; Shipley, Martin J.; Lentjes, Marleen A. H.; Khaw, Kay-Tee; Brunner, Eric; Key, Tim J.; Wareham, Nicholas J.

2015-01-01

Dietary recommendations to promote health include fresh, frozen and tinned fruit, but few studies have examined the health benefits of tinned fruit. We therefore studied the association between tinned fruit consumption and mortality. We followed up participants from three prospective cohorts in the United Kingdom: 22,421 participants from the European Prospective Investigation into Cancer and Nutrition (EPIC)-Norfolk cohort (1993–2012), 52,625 participants from the EPIC-Oxford cohort (1993–2012), and 7440 participants from the Whitehall II cohort (1991–2012), all reporting no history of heart attack, stroke, or cancer when entering these studies. We estimated the association between frequency of tinned fruit consumption and all cause mortality (primary outcome measure) using Cox regression models within each cohort, and pooled hazard ratios across cohorts using random-effects meta-analysis. Tinned fruit consumption was assessed with validated food frequency questionnaires including specific questions about tinned fruit. During 1,305,330 person years of follow-up, 8857 deaths occurred. After adjustment for lifestyle factors and risk markers the pooled hazard ratios (95% confidence interval) of all cause mortality compared with the reference group of tinned fruit consumption less often than one serving per month were: 1.05 (0.99, 1.12) for one to three servings per month, 1.10 (1.03, 1.18) for one serving per week, and 1.13 (1.04, 1.23) for two or more servings per week. Analysis of cause-specific mortality showed that tinned fruit consumption was associated with mortality from cardiovascular causes and from non-cardiovascular, non-cancer causes. In a pooled analysis of three prospective cohorts from the United Kingdom self-reported tinned fruit consumption in the 1990s was weakly but positively associated with mortality during long-term follow-up. These findings raise questions about the evidence underlying dietary recommendations to promote tinned fruit consumption as part of a healthy diet. PMID:25714554

7 CFR 1780.33 - Application requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... time lines. (g) The applicant's Internal Revenue Service Taxpayer Identification Number (TIN). The TIN will be used by the Agency to assign a case number which will be the applicant's or transferee's TIN...

7 CFR 1780.33 - Application requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... time lines. (g) The applicant's Internal Revenue Service Taxpayer Identification Number (TIN). The TIN will be used by the Agency to assign a case number which will be the applicant's or transferee's TIN...

7 CFR 1780.33 - Application requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... time lines. (g) The applicant's Internal Revenue Service Taxpayer Identification Number (TIN). The TIN will be used by the Agency to assign a case number which will be the applicant's or transferee's TIN...

7 CFR 1780.33 - Application requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... time lines. (g) The applicant's Internal Revenue Service Taxpayer Identification Number (TIN). The TIN will be used by the Agency to assign a case number which will be the applicant's or transferee's TIN...

7 CFR 1780.33 - Application requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... time lines. (g) The applicant's Internal Revenue Service Taxpayer Identification Number (TIN). The TIN will be used by the Agency to assign a case number which will be the applicant's or transferee's TIN...

Core Temperature Measurement During Submaximal Exercise: Esophageal, Rectal, and Intestinal Temperatures

NASA Technical Reports Server (NTRS)

Lee, Stuart M. C.; Williams, W. Jon; Schneider, Suzanne M.

2000-01-01

The purpose of this study was to determine if intestinal temperature (Tin) might be in acceptable alternative to esophageal (Tes) and rectal temperature (Trec) to assess thermoregulation during supine exercise. We hypothesized that Tin would have values similar to Tes and a response time similar to Trec, but the rate of temperature change across time would not be different between measurement sites. Seven subjects completed a continuous supine protocol of 20 min of rest, 20 min of cycle exercise at 40% peak oxygen consumption (VO2pk), 20 min of cycle exercise at 65% V02pk, and 20 min of recovery. Tes, Trec, and Tin were recorded each min throughout the test. Temperatures were not different after 20 min of rest, but Trec was less than the Tes and Tin at the end of the 40% and 65% VO2pk stages. After 20 min of recovery, Tes was less than either Trec or Tin, which were not different from each other. Time to threshold for increased temperature from rest was greater for Trec than Tes but not different from Tin. Time to reach peak temperature was greater for Tin and Trec than Tes. Similarly, time to a decrease in temperature after exercise was greater for Trec than Tes, but not different from Tin. The rate of temperature change from threshold to the end of the 40% VO2pk stage was not different between measurement sites. However, the rate of change during recovery was more negative for Tes than Tin and Trec, which were different from each other. Measurement of Tin may he an acceptable alternative to Tes and Trec with an understanding of its limitations.

21 CFR 582.1139 - Ammonium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Additives § 582.1139 Ammonium hydroxide. (a) Product. Ammonium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1205 - Calcium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Additives § 582.1205 Calcium hydroxide. (a) Product. Calcium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

Magnesium Hydroxide

MedlinePlus

Magnesium hydroxide is used on a short-term basis to treat constipation.This medication is sometimes prescribed ... Magnesium hydroxide come as a tablet and liquid to take by mouth. It usually is taken as ...

Aluminum Hydroxide

MedlinePlus

Aluminum hydroxide is used for the relief of heartburn, sour stomach, and peptic ulcer pain and to ... Aluminum hydroxide comes as a capsule, a tablet, and an oral liquid and suspension. The dose and ...

21 CFR 582.1205 - Calcium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Additives § 582.1205 Calcium hydroxide. (a) Product. Calcium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1139 - Ammonium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Additives § 582.1139 Ammonium hydroxide. (a) Product. Ammonium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1205 - Calcium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Additives § 582.1205 Calcium hydroxide. (a) Product. Calcium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1139 - Ammonium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Additives § 582.1139 Ammonium hydroxide. (a) Product. Ammonium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1139 - Ammonium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Additives § 582.1139 Ammonium hydroxide. (a) Product. Ammonium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1139 - Ammonium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Additives § 582.1139 Ammonium hydroxide. (a) Product. Ammonium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

21 CFR 582.1205 - Calcium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Additives § 582.1205 Calcium hydroxide. (a) Product. Calcium hydroxide. (b) Conditions of use. This substance is generally recognized as safe when used in accordance with good manufacturing or feeding...

Pretreatment of rapeseed straw by sodium hydroxide.

PubMed

Kang, Kyeong Eop; Jeong, Gwi-Taek; Park, Don-Hee

2012-06-01

Pretreatment method for rapeseed straw by sodium hydroxide was investigated for production of bioethanol and biobutanol. Various pretreatment parameters, including temperature, time, and sodium hydroxide concentration were optimized using a statistical method which is a central composite design of response surface methodology. In the case of sodium hydroxide pretreatment, optimal pretreatment conditions were found to be 7.9% sodium hydroxide concentration, 5.5 h of reaction time, and 68.4 °C of reaction temperature. The maximum glucose yield which can be recovered by enzymatic hydrolysis at the optimum conditions was 95.7% and the experimental result was 94.0 ± 4.8%. This experimental result was in agreement with the model prediction. An increase of surface area and pore size in pretreated rapeseed straw by sodium hydroxide pretreatment was observed by scanning electron microscope.

Nanostructured antistatic and antireflective thin films made of indium tin oxide and silica over-coat layer

NASA Astrophysics Data System (ADS)

Cho, Young-Sang; Hong, Jeong-Jin; Yang, Seung-Man; Choi, Chul-Jin

2010-08-01

Stable dispersion of colloidal indium tin oxide nanoparticles was prepared by using indium tin oxide nanopowder, organic solvent, and suitable dispersants through attrition process. Various comminution parameters during the attrition step were studied to optimize the process for the stable dispersion of indium tin oxide sol. The transparent and conductive films were fabricated on glass substrate using the indium tin oxide sol by spin coating process. To obtain antireflective function, partially hydrolyzed alkyl silicate was deposited as over-coat layer on the pre-fabricated indium tin oxide film by spin coating technique. This double-layered structure of the nanostructured film was characterized by measuring the surface resistance and reflectance spectrum in the visible wavelength region. The final film structure was enough to satisfy the TCO regulations for EMI shielding purposes.

Sodium hydroxide poisoning

MedlinePlus

Sodium hydroxide is a very strong chemical. It is also known as lye and caustic soda. This ... poisoning from touching, breathing in (inhaling), or swallowing sodium hydroxide. This article is for information only. Do ...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

Low resistivity contact to iron-pnictide superconductors

DOEpatents

Tanatar, Makariy; Prozorov, Ruslan; Ni, Ni; Bud& #x27; ko, Sergey; Canfield, Paul

2013-05-28

Method of making a low resistivity electrical connection between an electrical conductor and an iron pnictide superconductor involves connecting the electrical conductor and superconductor using a tin or tin-based material therebetween, such as using a tin or tin-based solder. The superconductor can be based on doped AFe.sub.2As.sub.2, where A can be Ca, Sr, Ba, Eu or combinations thereof for purposes of illustration only.

Uptake and Fate of Tri-N-Butyltin Cation in Estuarine Bacteria,

DTIC Science & Technology

1982-04-02

as well as Yamada and co-workers [31] found trialkyltins, especially tripropyl- tin (TPT) and tributyltin ( TBT ), had the highest antiw-,’.?ial...tin-resistant estuarine bacteria was studied. The bacterial isolates accumulated tributyltin to 3.7 to 7.7 mg tin per g dry weight of cells by a non...chromatography-atomic absorption spectrophotometry and tin-selective purge and trap flame photometric gas chromatography for possible tributyltin

Influence of implantation on the electrochemical properties of smooth and porous TiN coatings for stimulation electrodes

NASA Astrophysics Data System (ADS)

Meijs, S.; Sørensen, C.; Sørensen, S.; Rechendorff, K.; Fjorback, M.; Rijkhoff, N. J. M.

2016-04-01

Objective. To determine whether changes in electrochemical properties of porous titanium nitride (TiN) electrodes as a function of time after implantation are different from those of smooth TiN electrodes. Approach. Eight smooth and 8 porous TiN coated electrodes were implanted in 8 rats. Before implantation, voltage transients, cyclic voltammograms and impedance spectra were recorded in phosphate buffered saline (PBS). After implantation, these measurements were done weekly to investigate how smooth and porous electrodes were affected by implantation. Main results. The electrode capacitance of the porous TiN electrodes decreased more than the capacitance of the smooth electrodes due to acute implantation under fast measurement conditions (such as stimulation pulses). This indicates that protein adhesion presents a greater diffusion limitation for counter-ions for the porous than for the smooth electrodes. The changes in electrochemical properties during the implanted period were similar for smooth and porous TiN electrodes, indicating that cell adhesion poses a similar diffusion limitation for smooth and porous electrodes. Significance. This knowledge can be used to optimize the porous structure of the TiN film, so that the effect of protein adhesion on the electrochemical properties is diminished. Alternatively, an additional coating could be applied on the porous TiN that would prevent or minimize protein adhesion.

Silver-tin alloys and amalgams: electrochemical considerations.

PubMed

Mueller, H J

1980-01-01

The corrosion potential and anodic polarization profiles of a representative number of silver-tin alloys and their corresponding amalgams in a physiological solution were determined and compared to their microstructures. For the alloys with tin-content greater than 27%(wt) and for all amalgams, the corrosion process is related to the attack of free tin for the alloys and to the gamma-2 tin for the amalgams. The gamma-2 concentration in the amalgams increases with an increase in tin-content. For alloys with tin-content less than 27%, the corrosion process is even more restricted than for the process observed with pure silver. From a developed theory based upon the potential-time and polarization results, association of the O2 reduction process on a SnO cathodic film to an intermediate specie of H2O2 is made. The rate of H2O2 decomposition on a SnO surface in a four electron process is thought to control the O2 reduction overvoltage. The O2 reduction overvoltage decreases with increases in the silver-content of the amalgam, particularily seen with the 8 and 12% tin compositions. Due to the polarization induced corrosion process, a phase with high silver and high mercury concentrations was observed over the unreacted particles.

Role of point defects and HfO2/TiN interface stoichiometry on effective work function modulation in ultra-scaled complementary metal-oxide-semiconductor devices

NASA Astrophysics Data System (ADS)

Pandey, R. K.; Sathiyanarayanan, Rajesh; Kwon, Unoh; Narayanan, Vijay; Murali, K. V. R. M.

2013-07-01

We investigate the physical properties of a portion of the gate stack of an ultra-scaled complementary metal-oxide-semiconductor (CMOS) device. The effects of point defects, such as oxygen vacancy, oxygen, and aluminum interstitials at the HfO2/TiN interface, on the effective work function of TiN are explored using density functional theory. We compute the diffusion barriers of such point defects in the bulk TiN and across the HfO2/TiN interface. Diffusion of these point defects across the HfO2/TiN interface occurs during the device integration process. This results in variation of the effective work function and hence in the threshold voltage variation in the devices. Further, we simulate the effects of varying the HfO2/TiN interface stoichiometry on the effective work function modulation in these extremely-scaled CMOS devices. Our results show that the interface rich in nitrogen gives higher effective work function, whereas the interface rich in titanium gives lower effective work function, compared to a stoichiometric HfO2/TiN interface. This theoretical prediction is confirmed by the experiment, demonstrating over 700 meV modulation in the effective work function.

Lifetime of Sodium Beta-Alumina Membranes in Molten Sodium Hydroxide

DTIC Science & Technology

2008-07-01

ABSTRACT Summary: Sodium metal can be made by electrolysis of molten sodium hydroxide in sodium beta-alumina membrane electrolysis cells... electrolysis of molten sodium hydroxide in sodium ”-alumina membrane electrolysis cells. However, there are some uncertainties about the lifetime of the...the properties of the membrane degrade upon long term contact with molten sodium hydroxide. Electrolysis cells were designed, but it proved

Tin-silver-bismuth solders for electronics assembly

DOEpatents

Vianco, Paul T.; Rejent, Jerome A.

1995-01-01

A lead-free solder alloy for electronic assemblies composed of a eutectic alloy of tin and silver with a bismuth addition, x, of 0

Tin-silver-bismuth solders for electronics assembly

DOEpatents

Vianco, P.T.; Rejent, J.A.

1995-08-08

A lead-free solder alloy is disclosed for electronic assemblies composed of a eutectic alloy of tin and silver with a bismuth addition, x, of 0

The oxidation of carbon monoxide using tin oxide based catalysts

NASA Technical Reports Server (NTRS)

Sampson, Christopher F.; Jorgensen, Norman

1990-01-01

The preparation conditions for precious metal/tin oxide catalysts were optimized for maximum carbon monoxide/oxygen recombination efficiency. This was achieved by controlling the tin digestion, the peptization to form the sol, the calcination process and the method of adding the precious metals. Extensive studies of the tin oxide structure were carried out over the temperature range 20 to 500 C in air or hydrogen environments using Raman scattering and X ray diffraction. Adsorbed species on tin oxide, generated in an environment containing carbon monoxide, gave rise to a Raman band at about 1600 cm(exp -1) which was assigned to carbonaceous groups, possible carbonate.

Tribological characterization of TiN coatings prepared by magnetron sputtering

NASA Astrophysics Data System (ADS)

Makwana, Nishant S.; Chauhan, Kamlesh V.; Sonera, Akshay L.; Chauhan, Dharmesh B.; Dave, Divyeshkumar P.; Rawal, Sushant K.

2018-05-01

Titanium nitride (TiN) coating deposited on aluminium and brass pin substrates using RF reactive magnetron sputtering. The structural properties and surface morphology were characterized by X-ray diffraction (XRD), atomic force microscope (AFM) and field emission scanning electron microscope (FE-SEM). There was formation of (101) Ti2N, (110) TiN2 and (102) TiN0.30 peaks at 3.5Pa, 2Pa and 1.25Pa sputtering pressure respectively. The tribological properties of coating were inspected using pin on disc tribometer equipment. It was observed that TiN coated aluminium and brass pins demonstrated improved wear resistance than uncoated aluminium and brass pins.

Bonding in Some Zintl Phases: A Study by Tin-119 Mössbauer Spectroscopy

NASA Astrophysics Data System (ADS)

Asbrand, M.; Berry, F. J.; Eisenmann, B.; Kniep, R.; Smart, L. E.; Thied, R. C.

1995-09-01

The 119Sn Mössbauer parameters for a range of Zintl phase compounds are reported. The compounds containing tetrahedrally coordinated tin of composition M5SnX3 (M = Na, K; X = P, As, Sb) have chemical isomer shifts close to that of grey-tin and can be considered to be covalently bonded species. The layer structures of composition KSnX (X = As, Sb) and double-layer compounds M Sn2X2 (M = Na, Sr; X = As, Sb) have tin in a distorted octahedral environment. The chemical isomer shifts are closer to that of white-tin and can be interpreted in terms of metallic bonding.

99M-Technetium labeled tin colloid radiopharmaceuticals

DOEpatents

Winchell, Harry S.; Barak, Morton; Van Fleet, III, Parmer

1976-07-06

An improved 99m-technetium labeled tin(II) colloid, size-stabilized for reticuloendothelial organ imaging without the use of macromolecular stabilizers and a packaged tin base reagent and an improved method for making it are disclosed.

Determination of total tin in geological materials by electrothermal atomic-absorption spectrophotometry using a tungsten-impregnated graphite furnace

USGS Publications Warehouse

Zhou, L.; Chao, T.T.; Meier, A.L.

1984-01-01

An electrothermal atomic-absorption spectrophotometric method is described for the determination of total tin in geological materials, with use of a tungsten-impregnated graphite furnace. The sample is decomposed by fusion with lithium metaborate and the melt is dissolved in 10% hydrochloric acid. Tin is then extracted into trioctylphosphine oxide-methyl isobutyl ketone prior to atomization. Impregnation of the furnace with a sodium tungstate solution increases the sensitivity of the determination and improves the precision of the results. The limits of determination are 0.5-20 ppm of tin in the sample. Higher tin values can be determined by dilution of the extract. Replicate analyses of eighteen geological reference samples with diverse matrices gave relative standard deviations ranging from 2.0 to 10.8% with an average of 4.6%. Average tin values for reference samples were in general agreement with, but more precise than, those reported by others. Apparent recoveries of tin added to various samples ranged from 95 to 111% with an average of 102%. ?? 1984.

Morphology and Gas-Sensing Properties of Tin Oxide Foams with Dual Pore Structure

NASA Astrophysics Data System (ADS)

Nam, Kyungju; Kim, Hyeong-Gwan; Choi, Hyelim; Park, Hyeji; Kang, Jin Soo; Sung, Yung-Eun; Lee, Hee Chul; Choe, Heeman

2017-06-01

Tin oxide is a commonly used gas-sensing material, which can be applied as an n- or p-type gas sensor. To improve the gas-sensing performance of tin oxide, we successfully synthesized tin oxide foam via an ice-templating or freeze-casting method. The tin oxide foam samples showed different morphological features depending on the major processing parameters, which include sintering temperature, sintering time, and the amount of added powder. Based on scanning electron microscopy images, we could identify dual pore structure of tin oxide foam containing `wall' pores ranging from 5.3 μm to 10.7 μm, as well as smaller secondary pores (a few micrometers in size) on the wall surfaces. Gas-sensing performance tests for the synthesized tin oxide foams reveal a sensitivity of 13.1, a response time of 192 s, and a recovery time of 160 s at an ethanol gas concentration of 60 ppm at 300°C. This is a remarkable result given that it showed p-type semiconductor behavior and was used without the addition of any catalyst.

The application and research status of tin whisker formation in electric usage

NASA Astrophysics Data System (ADS)

Zhao, Heng; Liu, Qing-bin; Lan, Yuan-pei; Wang, Hua; Yao, Da-wei

2017-05-01

`Hair Like' crystalline structure grows from most pure tin or zinc finishes. Usually, the diameter of tin whisker is up to 10 mm and the length of tin whisker is typically 1 µm. In detail, the questions for tin whisker formation are classified into 6 categories: 1. Residual stress with in the tin plating; 2. Intermetallic Formation; 3. Externally Applied Compressive Stress; 4. Bending and Stretching; 5. Scratches and Nicks; 6. Coefficient of Thermal Expansion Mismatches. The result shows that, whisker formation could causes electrical short circuit (High current of whisker melting), debris contamination (Sensitive Optical and Micro Electrical Mechanical System) and metal vapor (Vaporize Damage). Thus, it is suggested that environmental tests and standards (Whisker Shape, Temperature, Pressure, Moisture, Thermal Cycling, and Electrical Field) are required for suppressing whisker formation. Nowadays, the new standards committee of Europe Union acts RoHS (Restriction of certain Hazardous Substances) and WEEE (Waste Electrical and Electronic Equipment) to restrict Pb usage. Thus, new compounds adding to alloys to suppress whiskers are required in electronic application area. In summary, the tin whisker formation is largely influenced by compositions and precipitations.

UV-visible spectroscopic estimation of photodegradation of rhodamine-B dye using tin(IV) oxide nanoparticles.

PubMed

Sangami, G; Dharmaraj, N

2012-11-01

Nanocrystalline, tin(IV) oxide (SnO(2)) particles has been prepared by thermal decomposition of tin oxalate precursor obtained from the reactions of tin(IV) chloride and sodium oxalate using eggshell membrane (ESM). The as-prepared SnO(2) nanoparticles were characterized by thermal studies, transmission electron microscopy (TEM), powder X-ray diffraction (XRD), Raman, FT-IR and UV-visible studies and used as a photocatalyst for the degradation of rhodamine-B (Rh-B) dye. The size of the prepared nanoparticles was in the range of 5-12nm as identified from the TEM images. Powder XRD data revealed the presence of a tetragonal, rutile crystalline phase of the tin(IV) oxide nanoparticles. Thermal analysis showed that the decomposition of tin oxalate precursor to yield the titled tin(IV) oxide nanoparticles was completed below 500°C. The extent of degradation of Rh-B in the presence of SnO(2) monitored by absorption spectral measurements demonstrated that 94.48% of the selected dye was degraded upon irradiation with UV light for 60 min. Copyright © 2012 Elsevier B.V. All rights reserved.

Inductively coupled plasma atomic emission spectrometric determination of tin in canned food.

PubMed

Sumitani, H; Suekane, S; Nakatani, A; Tatsuka, K

1993-01-01

Various canned foods were digested sequentially with HNO3 and HCl, diluted to 100 mL, and filtered, and then tin was determined by inductively coupled plasma atomic emission spectrometry (ICP/AES). Samples of canned Satsuma mandarin, peach, apricot, pineapple, apple juice, mushroom, asparagus, evaporated milk, short-necked clam, spinach, whole tomato, meat, and salmon were evaluated. Sample preparations did not require time-consuming dilutions, because ICP/AES has wide dynamic range. The standard addition method was used to determine tin concentration. Accuracy of the method was tested by analyzing analytical standards containing tin at 2 levels (50 and 250 micrograms/g). The amounts of tin found for the 50 and 250 micrograms/g levels were 50.5 and 256 micrograms/g, respectively, and the repeatability coefficients of variation were 4.0 and 3.8%, respectively. Recovery of tin from 13 canned foods spiked at 2 levels (50 and 250 micrograms/g) ranged from 93.9 to 109.4%, with a mean of 99.2%. The quantitation limit for tin standard solution was about 0.5 microgram/g.

Effects of vanadium ion implantation on microstructure, mechanical and tribological properties of TiN coatings

NASA Astrophysics Data System (ADS)

Deng, Bin; Tao, Ye; Guo, Deliang

2012-09-01

TiN coatings were deposited on the substrates of cemented carbide (WC-TiC-Co) by Magnetic Filter Arc Ion Plating (MFAIP) and then implanted with vanadium through Metal Vacuum Vapor Arc (MEVVA) ion source with the doses of 1 × 1017 and 5 × 1017 ions/cm2 at 40 kV. The microstructures and chemical compositions of the V-implanted TiN coatings were investigated using Glancing Incidence X-ray Diffraction (GIXRD) and X-ray Photoelectron Spectroscopy (XPS), together with the mechanical and tribological properties of coatings were characterized using nano-indentation and ball-on-disk tribometer. It was found that the diffraction peaks of the V-implanted TiN coatings at the doses of 5 × 1017 ions/cm2 shifted to higher angles and became broader. The hardness and elastic modulus of TiN coatings increased after V ion implantation. The wear mechanism for both un-implanted and V-implanted TiN coatings against GCr15 steel ball was adhesive wear, and the V-implanted TiN coatings had a lower friction coefficient as well as a better wear resistance

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bortolaz de Oliveira, Henrique; Wypych, Fernando, E-mail: wypych@ufpr.br

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO{sub 4}{sup 2−}/g of material, respectively. Although the removal values obtained for Zn/NiHN andmore » Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO{sub 4}{sup 2−}/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated. - Highlights: • Zinc hydroxide nitrate and Zn/Ni hydroxide nitrate or acetate were synthesized. • The interlayer anions were replaced by chromate anions at pH=8.0. • Only Zn/Ni hydroxide nitrate or acetate have the structure preserved after exchange. • Fast exchange reaction and high capacity of chromate removal were observed. • Magnetic materials were obtained to facilitate the solids removal the from solutions.« less

Effect of the Association of Nonsteroidal Anti-inflammatory and Antibiotic Drugs on Antibiofilm Activity and pH of Calcium Hydroxide Pastes.

PubMed

de Freitas, Rafaela Pignatti; Greatti, Vanessa Raquel; Alcalde, Murilo Priori; Cavenago, Bruno Cavalini; Vivan, Rodrigo Ricci; Duarte, Marco Antonio Hungaro; Weckwerth, Ana Carolina Villas Bôas; Weckwerth, Paulo Henrique

2017-01-01

The objective of the present study was to evaluate the in vitro antibiofilm activity and pH of calcium hydroxide associated with different nonsteroidal anti-inflammatory drugs (NSAIDs). The groups analyzed were as follows: group 1, calcium hydroxide paste with propylene glycol; group 2, calcium hydroxide paste with propylene glycol + 5% diclofenac sodium; group 3, calcium hydroxide paste with propylene glycol + 5% ibuprofen; group 4, calcium hydroxide paste with propylene glycol + 5% ciprofloxacin; and group 6, positive control (without medication). For analysis of the pH, the pastes were inserted into tubes and immersed in flasks containing ultrapure water. At the time intervals of 3, 24, 72, and 168 hours, the pH was measured with a calibrated pH meter. For microbial analysis, biofilm was induced in 30 bovine dentin blocks for 21 days. Subsequently, the pastes were placed on the blocks with biofilm for 7 days. Afterward, the pastes were removed by irrigation with sterile water, and the specimens were analyzed with a laser scanning confocal microscope with the 50 μL Live/Dead BacLight Bacterial Viability solution L7012 Kit (Molecular Probes, Inc, Eugene, OR). Data were subjected to statistical analysis at a significance level of 5%. The highest pH values were found for calcium hydroxide associated with ciprofloxacin in all periods analyzed. With the exception of pure calcium hydroxide paste, the other groups showed statistically significant differences (P < .05) in comparison with the positive control. The association of NSAIDs or antibiotic did not interfere with the pH of calcium hydroxide paste and increased the antimicrobial action of calcium hydroxide paste against Enterococcus faecalis biofilm formation. Published by Elsevier Inc.

Intercalation studies of zinc hydroxide chloride: Ammonia and amino acids

NASA Astrophysics Data System (ADS)

Arízaga, Gregorio Guadalupe Carbajal

2012-01-01

Zinc hydroxide chloride (ZHC) is a layered hydroxide salt with formula Zn5(OH)8Cl2·2H2O. It was tested as intercalation matrix for the first time and results were compared with intercalation products of the well-known zinc hydroxide nitrate and a Zn/Al layered double hydroxide. Ammonia was intercalated into ZHC, while no significant intercalation occurred in ZHN. Aspartic acid intercalation was only achieved by co-precipitation at pH=10 with ZHC and pH=8 with zinc hydroxide nitrate. Higher pH resistance in ZHC favored total deprotonation of both carboxylic groups of the Asp molecule. ZHC conferred more thermal protection against Asp combustion presenting exothermic peaks even at 452 °C while the exothermic event in ZHN was 366 °C and in the LDH at 276 °C.

Synthesis and adsorption properties of flower-like layered double hydroxide by a facile one-pot reaction with an eggshell membrane as assistant

NASA Astrophysics Data System (ADS)

Li, Songnan; Zhang, Jiawei; Jamil, Saba; Cai, Qinghai; Zang, Shuying

In this paper, flower-like layered double hydroxides were synthesized with eggshell membrane assistant. The as-prepared samples were characterized by a series of techniques including X-ray diffraction (XRD), Fourier transform infrared spectroscopy, Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Thermal gravity-differential thermal analysis and Nitrogen sorption/desorption. The resulting layered double hydroxides were composed of nanoplates with edge-to-face particle interactions. The specific surface area and total pore volume of the as-prepared flower-like layered double hydroxides were 160m2/g and 0.65m3/g, respectively. The adsorption capacity of flower-like layered double hydroxides to Congo Red was 258mg/g, which was higher than that of layered double hydroxides synthesized by the traditional method.

Hydroxide Solvation and Transport in Anion Exchange Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Chen; Tse, Ying-Lung Steve; Lindberg, Gerrick E.

Understanding hydroxide solvation and transport in anion exchange membranes (AEMs) can provide important insight into the design principles of these new membranes. To accurately model hydroxide solvation and transport, we developed a new multiscale reactive molecular dynamics model for hydroxide in aqueous solution, which was then subsequently modified for an AEM material. With this model, we investigated the hydroxide solvation structure and transport mechanism in the membrane. We found that a relatively even separation of the rigid side chains produces a continuous overlapping region for hydroxide transport that is made up of the first hydration shell of the tethered cationicmore » groups. Our results show that hydroxide has a significant preference for this overlapping region, transporting through it and between the AEM side chains with substantial contributions from both vehicular (standard diffusion) and Grotthuss (proton hopping) mechanisms. Comparison of the AEM with common proton exchange membranes (PEMs) showed that the excess charge is less delocalized in the AEM than the PEMs, which is correlated with a higher free energy barrier for proton transfer reactions. The vehicular mechanism also contributes considerably more than the Grotthuss mechanism for hydroxide transport in the AEM, while our previous studies of PEM systems showed a larger contribution from the Grotthuss mechanism than the vehicular mechanism for proton transport. The activation energy barrier for hydroxide diffusion in the AEM is greater than that for proton diffusion in PEMs, implying a more significant enhancement of ion transport in the AEM at elevated temperatures.« less

The effect of calcium hydroxide on the antibiotic component of Odontopaste and Ledermix paste.

PubMed

Athanassiadis, M; Jacobsen, N; Nassery, K; Parashos, P

2013-06-01

To investigate the chemical interaction of calcium hydroxide with the antibiotics demeclocycline calcium in Ledermix Paste and clindamycin hydrochloride in Odontopaste. Validated methods were developed to analyse the interaction of calcium hydroxide in two forms, Pulpdent and calcium hydroxide powder, with the two antibiotics. High-performance liquid chromatography (HPLC) was used to analyse the mixed samples of the pastes and calcium hydroxide. The concentration of demeclocycline calcium over 0-, 1-, 18-, 24-, 72-h and 7-day time-points was determined. The concentration of clindamycin hydrochloride over 1-, 6-, 24-, 72-h and 7-day time-points was determined. All tests with HPLC involved testing of the standard in duplicate alongside the samples. Linearity, precision and specificity of the testing procedures and apparatus were validated. Descriptive statistics are provided. The antibiotics in both Odontopaste and Ledermix Paste were affected by the addition of calcium hydroxide. When mixed with calcium hydroxide powder, Odontopaste had a 2% loss of clindamycin hydrochloride over 7 days, but when mixed with Pulpdent, there was a 36% loss over 7 days. Ledermix Paste showed an 80% loss of demeclocycline calcium over 7 days when mixed with calcium hydroxide powder and a 19% loss when mixed with Pulpdent over the 7-day period. The addition of calcium hydroxide to Odontopaste or Ledermix Paste results in reductions of the respective antibiotic over a 7-day time period. © 2012 International Endodontic Journal. Published by Blackwell Publishing Ltd.

Hydroxide Solvation and Transport in Anion Exchange Membranes.

PubMed

Chen, Chen; Tse, Ying-Lung Steve; Lindberg, Gerrick E; Knight, Chris; Voth, Gregory A

2016-01-27

Understanding hydroxide solvation and transport in anion exchange membranes (AEMs) can provide important insight into the design principles of these new membranes. To accurately model hydroxide solvation and transport, we developed a new multiscale reactive molecular dynamics model for hydroxide in aqueous solution, which was then subsequently modified for an AEM material. With this model, we investigated the hydroxide solvation structure and transport mechanism in the membrane. We found that a relatively even separation of the rigid side chains produces a continuous overlapping region for hydroxide transport that is made up of the first hydration shell of the tethered cationic groups. Our results show that hydroxide has a significant preference for this overlapping region, transporting through it and between the AEM side chains with substantial contributions from both vehicular (standard diffusion) and Grotthuss (proton hopping) mechanisms. Comparison of the AEM with common proton exchange membranes (PEMs) showed that the excess charge is less delocalized in the AEM than the PEMs, which is correlated with a higher free energy barrier for proton transfer reactions. The vehicular mechanism also contributes considerably more than the Grotthuss mechanism for hydroxide transport in the AEM, while our previous studies of PEM systems showed a larger contribution from the Grotthuss mechanism than the vehicular mechanism for proton transport. The activation energy barrier for hydroxide diffusion in the AEM is greater than that for proton diffusion in PEMs, implying a more significant enhancement of ion transport in the AEM at elevated temperatures.

Tinless Solder Investigation

DTIC Science & Technology

1937-06-24

tin solder. 4. By soldering coated thin (.015*) plates of tin- plate, terne-plate and galvanised iron with this mixture, the tensile strength in...9700 lbs/ln2 Average 9500 lbs/ln2 •The plates used In this test were tin-plate. Tests on bright annealed, terne-plate, brass and galvanised ...plates (tin-plate, terne- plate and galvanised iron) had coatings, it was impossible to use emery oloth OB them to completely remove the rust or

Synthesis and surface chemistry of high quality wurtzite and kesterite Cu2ZnSnS4 nanocrystals using tin(II) 2-ethylhexanoate as a new tin source.

PubMed

Gabka, Grzegorz; Bujak, Piotr; Gryszel, Maciej; Ostrowski, Andrzej; Malinowska, Karolina; Zukowska, Grazyna Z; Agnese, Fabio; Pron, Adam; Reiss, Peter

2015-08-21

A novel synthesis method for the preparation of Cu2ZnSnS4 nanocrystals is presented using a liquid precursor of tin, namely tin(II) 2-ethylhexanoate, which yields small and nearly monodisperse NCs either in the kesterite or in the wurtzite phase depending on the sulfur source (elemental sulfur in oleylamine vs. dodecanethiol).

Synthesis of antimony-doped tin oxide (ATO) nanoparticles by the nitrate-citrate combustion method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Jianrong; Gao Lian

2004-12-02

Antimony-doped tin oxide (ATO) nanoparticles having rutile structure have been synthesized by the combustion method using citric acid (CA) as fuel and nitrate as an oxidant, the metal sources were granulated tin and Sb{sub 2}O{sub 3}. The influence of citric acid (fuel) to metal ratio on the average crystallite size, specific surface area and morphology of the nanoparticles has been investigated. X-ray diffraction showed the tin ions were reduced to elemental tin during combustion reaction. The average ATO crystallite size increased with the increase of citric acid (fuel). Powder morphology and the comparison of crystallite size and grain size showsmore » that the degree of agglomeration of the powder decreased with an increase of the ratio. The highest specific surface area was 37.5 m{sup 2}/g when the citric acid to tin ratio was about 6.« less

Assessment of organotin and tin-free antifouling paints contamination in the Korean coastal area.

PubMed

Lee, Mi-Ri-Nae; Kim, Un-Jung; Lee, In-Seok; Choi, Minkyu; Oh, Jeong-Eun

2015-10-15

Twelve organotins (methyl-, octyl-, butyl-, and phenyl-tin), and eight tin-free antifouling paints and their degradation products were measured in marine sediments from the Korean coastal area, and Busan and Ulsan bays, the largest harbor area in Korea. The total concentration of tin-free antifouling paints was two- to threefold higher than the total concentration of organotins. Principal component analysis was used to identify sites with relatively high levels of contamination in the inner bay area of Busan and Ulsan bays, which were separated from the coastal area. In Busan and Ulsan bays, chlorothalonil and DMSA were more dominant than in the coastal area. However, Sea-Nine 211 and total diurons, including their degradation products, were generally dominant in the Korean coastal area. The concentrations of tin and tin-free compounds were significantly different between the east and west coasts. Copyright © 2015 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schulberg, M.T.; Allendorf, M.D.; Outka, D.A.

NH{sub 3} is an important component of many chemical vapor deposition (CVD) processes for TiN films, which are used for diffusion barriers and other applications in microelectronic circuits. In this study, the interaction of NH{sub 3} with TiN surfaces is examined with temperature programmed desorption (TPD) and Auger electron spectroscopy. NH{sub 3} has two adsorption states on TiN: a chemisorbed state and a multilayer state. A new method for analyzing TPD spectra in systems with slow pumping speeds yields activation energies for desorption for the two states of 24 kcal/mol and 7.3 kcal/mol, respectively. The sticking probability into the chemisorptionmore » state is {approximately}0.06. These results are discussed in the context of TiN CVD. In addition, the high temperature stability of TiN is investigated. TiN decomposes to its elements only after heating to 1300 K, showing that decomposition is unlikely to occur under CVD conditions.« less

Positive Active Material For Alkaline Electrolyte Storage Battert Nickel Electrodes

DOEpatents

Bernard, Patrick; Baudry, Michelle

2000-12-05

A method of manufacturing a positive active material for nickel electrodes of alkaline storage batteries which consists of particles of hydroxide containing mainly nickel and covered with a layer of a hydroxide phase based on nickel and yttrium is disclosed. The proportion of the hydroxide phase is in the range 0.15% to 3% by weight of yttrium expressed as yttrium hydroxide relative to the total weight of particles.

Synthesis, characterization, and evaluation of simple aluminum-based adsorbents for fluoride removal from drinking water.

PubMed

Du, Junyi; Sabatini, David A; Butler, Elizabeth C

2014-04-01

Simple aluminum (hydr)oxides and layered double hydroxides were synthesized using common chemicals and equipment by varying synthesis temperature, concentrations of extra sulfate and citrate, and metal oxide amendments. Aluminum (hydr)oxide samples were aged at either 25 or 200°C during synthesis and, in some cases, calcined at 600 °C. Despite yielding increased crystallinity and mineral phase changes, higher temperatures had a generally negative effect on fluoride adsorption. Addition of extra sulfate during synthesis of aluminum (hydr)oxides led to significantly higher fluoride adsorption capacity compared to aluminum (hydr)oxides prepared with extra citrate or no extra ligands. X-ray diffraction results suggest that extra sulfate led to the formation of both pseudoboehmite (γ-AlOOH) and basaluminite (Al4SO4(OH)10⋅4H2O) at 200 °C; energy dispersive X-ray spectroscopy confirmed the presence of sulfur in this solid. Treatment of aluminum (hydr)oxides with magnesium, manganese, and iron oxides did not significantly impact fluoride adsorption. While layered double hydroxides exhibited high maximum fluoride adsorption capacities, their adsorption capacities at dissolved fluoride concentrations close to the World Health Organization drinking water guideline of 1.5 mg L(-1) were much lower than those for the aluminum (hydr)oxides. Copyright © 2013 Elsevier Ltd. All rights reserved.

Arsenic removal from water

DOEpatents

Moore, Robert C [Edgewood, NM; Anderson, D Richard [Albuquerque, NM

2007-07-24

Methods for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical methods for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A method for continuous removal of arsenic from water is provided. Also provided is a method for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

The prognostic values of tumor-infiltrating neutrophils, lymphocytes and neutrophil/lymphocyte rates in bladder urothelial cancer.

PubMed

Liu, Kangkang; Zhao, Kun; Wang, Lining; Sun, Erlin

2018-05-20

Tumor-infiltrating neutrophils (TINs) and lymphocytes (TILs) are found to play essential roles in many tumors and associate with the prognosis of patients. But, the prognostic values of TINs, TILs and NLR (neutrophils-lymphocytes ratio) in bladder cancer (BC) are still undefined. The object of our study was to systematically interrogate the associations of these immune cells with clinical outcomes of BC patients. In our study, a total of 102 patients pathologically diagnosed with BC were included. CD66b + and CD8 + antibodies were used to mark neutrophils and CD8 + lymphocytes by immunohistochemistry. The results found that TINs and NLR were significantly associated with pathological T-stages of tumors (P < 0.01), but TILs were not. And TINs were also related to pathological tumor grades (P = 0.012). Regarding the prognostic values, TINs was related to the high risk of recurrence in non-muscle invasive BC (NMIBC) patients. Elevated TINs and NLR were associated with poor overall survivals of BC patients, whereas higher TILs were related to longer survivals (P < 0.01). Multivariate analysis showed that both of TINs (HR 2.427, 1.024-5.752, P = 0.044) and NLR (HR 3.529, 1.147-10.864, P = 0.028) were independent unfavorable prognosis markers. In conclusion, Tumor infiltrating immune cells, including TINs, TILs and NLR were important markers in predicting the prognosis of bladder cancer patients. TINs and NLR were more likely to be negative predictors, but TILs were favorable in patients with BC. Copyright © 2018 Elsevier GmbH. All rights reserved.

Evaluation of employee exposure to organic tin compounds used as stabilizers at PVC processing facilities.

PubMed

Boraiko, Carol; Batt, John

2005-02-01

Organic tin compounds are primary substances used as heat stabilizers by the polyvinyl chloride (PVC) industry. The use of these compounds in the PVC industry is generally well controlled, usually by automated processes. This study was conducted to provide an overview of worker exposure to organic tin compounds at PVC processing facilities and to verify that these exposures are below the threshold limit value (TLV((R))) set by the American Conference of Governmental Industrial Hygienists for organic tin. The basis of the TLV indicates the principal concern is to minimize adverse effects on immune function and the central nervous system from airborne exposure to organic tin. The TLV has a skin designation based on the potential for percutaneous absorption; the TLVs for inhalation exposures are based on the presumption that there is no concurrent exposure via the skin and oral ingestion routes. Personal exposure monitoring was conducted following the National Institute for Occupational Safety and Health (NIOSH) 5504 sampling method and a modified version of the NIOSH analytical method. The results were reported as"total tin."The data indicated no average exposure levels for individual tasks exceeded the organic tin TLV, and 96%of results the samples were less than 20%of the TLV. Only 1 sample of 102 exceeded the TLV, and the individual was wearing appropriate respiratory protection. Subsequent investigation indicated the highest exposures occurred while the operators were conducting tasks that included manual handling of the organic tin compounds. These data suggest manual operations may have a greater potential for organic tin exposure.

Effect of ammonium hydroxide on ultrastructure and tenderness of buffalo meat.

PubMed

Naveena, B M; Kiran, M; Reddy, K Sudhakar; Ramakrishna, C; Vaithiyanathan, S; Devatkal, Suresh K

2011-08-01

This study was conducted with an objective to improve the tenderness of tough buffalo meat using ammonium hydroxide. Buffalo meat chunks from Biceps femoris muscle were marinated with distilled water (control), 0.1%, 0.5% and 1.0% solution of ammonium hydroxide for 48 h at 4±1 °C and subjected to various physico-chemical analysis and ultrastructural studies. Ammonium hydroxide increased (P<0.05) the pH, water holding capacity (WHC), collagen solubility, total and salt soluble protein extractability and cooking yield. Reduction (P<0.05) in Warner-Bratzler shear force values were observed in all ammonium hydroxide treated samples compared to non-treated control. Electrophoretic pattern of muscle proteins exhibited reduction in the intensity and number of certain protein bands for 0.1% and 0.5% ammonium hydroxide treated samples compared to control. Scanning and transmission electron microscopy also revealed breakdown of endothelium layers surrounding muscle fibers and weakening of Z-discs respectively, in treated samples compared to controls. These results suggest that ammonium hydroxide might be used to tenderize tough buffalo meat. Copyright © 2011 Elsevier Ltd. All rights reserved.

Calcium hydroxide suppresses Porphyromonas endodontalis lipopolysaccharide-induced bone destruction.

PubMed

Guo, J; Yang, D; Okamura, H; Teramachi, J; Ochiai, K; Qiu, L; Haneji, T

2014-05-01

Porphyromonas endodontalis and its main virulence factor, lipopolysaccharide (LPS), are associated with the development of periapical diseases and alveolar bone loss. Calcium hydroxide is commonly used for endodontic therapy. However, the effects of calcium hydroxide on the virulence of P. endodontalis LPS and the mechanism of P. endodontalis LPS-induced bone destruction are not clear. Calcium hydroxide rescued the P. endodontalis LPS-suppressed viability of MC3T3-E1 cells and activity of nuclear factor-κB (NF-κB) in these cells, resulting in the reduced expression of interleukin-6 and tumor necrosis factor-α. In addition, calcium hydroxide inhibited P. endodontalis LPS-induced osteoclastogenesis by decreasing the activities of NF-κB, p38, and ERK1/2 and the expression of nuclear factor of activated T-cell cytoplasmic 1 in RAW264.7 cells. Calcium hydroxide also rescued the P. endodontalis LPS-induced osteoclastogenesis and bone destruction in mouse calvaria. Taken together, our present results indicate that calcium hydroxide suppressed bone destruction by attenuating the virulence of P. endodontalis LPS on bone cells.

77 FR 27438 - Certain Corrosion-Resistant Carbon Steel Flat Products From Korea: Final Results of Expedited...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-10

...- rolled steel products either plated or coated with tin, lead, chromium, chromium oxides, both tin and lead (``terne plate''), or both chromium and chromium oxides (``tin-free steel''), whether or not...

Effect of Composition of Alloys of Tin-Sodium Systems on Surface Tension

NASA Astrophysics Data System (ADS)

Alchagirov, B. B.; Kyasova, O. Kh.

2018-07-01

The results are presented from investigating the surface tensions of tin-sodium systems, along with original experimental data on the concentration dependences of the surface tensions of 19 tin-based sodium alloys obtained for samples of enhanced purity in a range of compositions with contents of 0.06 to 5.00 at % Na at T = 573 K. It is established that adding small amounts of sodium to tin greatly reduces the surface tensions of the studied melts. Calculations of sodium adsorption in alloys with tin show there is a maximum on the adsorption curve that corresponds to alloys with contents of around 1.5 at % Na in Sn.

Effect of pretreatment on a platinized tin oxide catalyst used for low-temperature CO-oxidation

NASA Technical Reports Server (NTRS)

Drawdy, Jean E.; Hoflund, Gar B.; Gardner, Steven D.; Yngvadottir, Eva; Schryer, David R.

1990-01-01

A commercial platinized tin oxide catalyst used for low-temperature CO oxidation has been characterized using ion scattering spectroscopy (ISS), Auger electron spectroscopy (AES) and Electron Spectroscopy for Chemical Analysis (ESCA) before and after reduction in 40 Torr of CO for 1 hour at various temperatures from 75 to 175 C. The reduction results in loss of surface oxygen, formation of metallic tin, conversion of platinum oxides to Pt-O-Sn and Pt(OH)2 and a small amount of metallic Pt which alloys with the tin. These results should be useful in understanding how the pretreatment temperature affects the catalytic activity of platinized tin oxide toward CO oxidation.

Melting of isolated tin nanoparticles

PubMed

Bachels; Guntherodt; Schafer

2000-08-07

The melting of isolated neutral tin cluster distributions with mean sizes of about 500 atoms has been investigated in a molecular beam experiment by calorimetrically measuring the clusters' formation energies as a function of their internal temperature. For this purpose the possibility to adjust the temperature of the clusters' internal degrees of freedom by means of the temperature of the cluster source's nozzle was exploited. The melting point of the investigated tin clusters was found to be lowered by 125 K and the latent heat of fusion per atom is reduced by 35% compared to bulk tin. The melting behavior of the isolated tin clusters is discussed with respect to the occurrence of surface premelting.

Prognostic value of intratumoral neutrophils in advanced gastric carcinoma in a high-risk area in northern Italy.

PubMed

Caruso, Rosario Alberto; Bellocco, Rino; Pagano, Marcello; Bertoli, Giovanni; Rigoli, Luciana; Inferrera, Cosimo

2002-08-01

Several lines of evidence indicate that neutrophils act nonspecifically against tumor cells. The correlation between tumor-infiltrating neutrophils (TINs) and clinicopathological features remains unclear and deserves to be investigated. To analyze the prognostic influence of TINs in gastric carcinoma, the authors selected 273 patients with advanced gastric carcinoma who underwent gastrectomy at Cremona Hospital (Lombardia, Italy) between 1990 and 1995 and followed them for a period of 5 years. The number of TINs was assessed in a semiquantitative manner using the mean value of 20 nonoverlapping high-power fields (magnification, 400x; 0.08 mm(2)). The patients were divided into two groups: patients with a moderate or extensive amount of TINs (n = 76; >10 TINs per 20 high-power fields) and patients with a minor amount of TINs (n = 197;

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

Rapeseed-straw enzymatic digestibility enhancement by sodium hydroxide treatment under ultrasound irradiation.

PubMed

Kang, Kyeong Eop; Jeong, Gwi-Taek; Park, Don-Hee

2013-08-01

In this study, we carried out sodium hydroxide and sonication pretreatments of rapeseed straw (Brassica napus) to obtain monosugar suitable for production of biofuels. To optimize the pretreatment conditions, we applied a statistical response-surface methodology. The optimal pretreatment conditions using sodium hydroxide under sonication irradiation were determined to be 75.0 °C, 7.0 % sodium hydroxide, and 6.8 h. For these conditions, we predicted 97.3 % enzymatic digestibility. In repeated experiments to validate the predicted value, 98.9 ± 0.3 % enzymatic digestibility was obtained, which was well within the range of the predicted model. Moreover, sonication irradiation was found to have a good effect on pretreatment in the lower temperature range and at all concentrations of sodium hydroxide. According to scanning electron microscopy images, the surface area and pore size of the pretreated rapeseed straw were modified by the sodium hydroxide pretreatment under sonication irradiation.

A tillering inhibition gene influences root–shoot carbon partitioning and pattern of water use to improve wheat productivity in rainfed environments

PubMed Central

Hendriks, P.W.; Kirkegaard, J.A.; Lilley, J.M.; Gregory, P.J.; Rebetzke, G.J.

2016-01-01

Genetic modification of shoot and root morphology has potential to improve water and nutrient uptake of wheat crops in rainfed environments. Near-isogenic lines (NILs) varying for a tillering inhibition (tin) gene and representing multiple genetic backgrounds were phenotyped in contrasting, controlled environments for shoot and root growth. Leaf area, shoot and root biomass were similar until tillering, whereupon reduced tillering in tin-containing NILs produced reductions of up to 60% in total leaf area and biomass, and increases in total root length of up to 120% and root biomass to 145%. Together, the root-to-shoot ratio increased two-fold with the tin gene. The influence of tin on shoot and root growth was greatest in the cv. Banks genetic background, particularly in the biculm-selected NIL, and was typically strongest in cooler environments. A separate de-tillering study confirmed greater root-to-shoot ratios with regular tiller removal in non-tin-containing genotypes. In validating these observations in a rainfed field study, the tin allele had a negligible effect on seedling growth but was associated with significantly (P<0.05) reduced tiller number (–37%), leaf area index (–26%), and spike number (–35%) to reduce plant biomass (–19%) at anthesis. Root biomass, root-to-shoot ratio at early stem elongation, and root depth at maturity were all increased in tin-containing NILs. Soil water use was slowed in tin-containing NILs, resulting in greater water availability, greater stomatal conductance, cooler canopy temperatures, and maintenance of green leaf area during grain-filling. Together these effects contributed to increases in harvest index and grain yield. In both the controlled and field environments, the tin gene was commonly associated with increased root length and biomass, but the significant influence of genetic background and environment suggests careful assessment of tin-containing progeny in selection for genotypic increases in root growth. PMID:26494729

Influence of different desapping agents on the incidence of sapburn, ripening behaviour and quality of mango.

PubMed

Barman, Kalyan; Asrey, Ram; Pal, R K; Jha, S K; Sharma, Swati

2015-01-01

Sapburn injury in mango is regarded as the most serious problem as it reduces the aesthetic appeal and downgrade the fruit quality with considerable economic losses. For the control of sapburn injury, physiologically mature mango fruits of cv. Chausa were harvested along with 5-8 cm stalk attached. Immediately after harvesting, fruits were de-stemmed and treated with different desapping agent solutions [calcium hydroxide (1 %), sodium hydroxide (1 %), alum (0.5 and 1 %)] by dipping them for 5 min. In control fruits, the pedicels were removed and sap was allowed to spread freely over the fruit surface. After treatment application, fruits were air-dried and stored at ambient condition (30 ± 2 °C) for 12 days. Among the treatments, fruits desapped with sodium hydroxide (1 %) showed significantly lower (7.6-fold) sapburn injury followed by alum (0.5 %) treatment than control. Respiration and ethylene evolution rates were also significantly suppressed and delayed with sodium hydroxide (1 %) treatment. Fruit firmness and functional properties like, antioxidant capacity, total carotenoids and total phenolics content were also found higher in sodium hydroxide (1 %) treated fruits. Pectin methyl esterase and polygalacturonase enzyme activity were recorded higher in fruits of control and calcium hydroxide treatment however; it was suppressed by sodium hydroxide and alum treatments. Fruit quality parameters like color, total soluble solids, titratable acidity and total sugars content were found higher in calcium hydroxide and sodium hydroxide treated fruits than control and alum treated fruits.

Structure, electronic properties, and oxygen incorporation/diffusion characteristics of the Σ 5 TiN(310)[001] tilt grain boundary

NASA Astrophysics Data System (ADS)

McKenna, Keith P.

2018-02-01

First principles calculations are employed to investigate the structure, electronic properties, and oxygen incorporation/diffusion characteristics of the Σ 5 TiN(310) tilt grain boundary with relevance to applications of polycrystalline TiN in microelectronics and protective coatings. We show that the grain boundary does not significantly modify electronic states near the Fermi energy but does induce an upward shift of up to 0.6 eV in a number of deeper occupied bands. We also show that oxygen is preferentially incorporated into the TiN grain boundary (GB) but must overcome relatively high activation energies for further diffusion. These predictions are consistent with the "stuffed barrier model" proposed to explain the good barrier characteristics of TiN. We also show that while the oxidizing power of TiN GBs is not sufficient to reduce HfO2 (a prototypical gate dielectric material), they can act as a scavenger for interstitial oxygen. Altogether, these results provide the much needed atomistic insights into the properties of a model GB in TiN and suggest a number of directions for future investigation.

High-performance Li-ion Sn anodes with enhanced electrochemical properties using highly conductive TiN nanotubes array as a 3D multifunctional support

NASA Astrophysics Data System (ADS)

Pu, Jun; Du, Hongxiu; Wang, Jian; Wu, Wenlu; Shen, Zihan; Liu, Jinyun; Zhang, Huigang

2017-08-01

High capacity electrodes are demanded to increase the energy and power density of lithium ion batteries. However, the cycling and rate properties are severely affected by the large volume changes caused by the lithium insertion and extraction. Structured electrodes with mechanically stable scaffolds are widely developed to mitigate the adverse effects of volume changes. Tin, as a promising anode material, receives great attentions because of its high theoretic capacity. There is a critical value of tin particle size above which tin anodes readily crack, leading to low cyclability. The electrode design using mechanical scaffolds must retain tin particles below the critical size and concurrently enable high volumetric capacity. It is a challenge to guarantee the critical size for high cyclability and space utilization for high volumetric capacity. This study provides a highly conductive TiN nanotubes array with submicron diameters, which enable thin tin coating without sacrificing the volumetric capacity. Such a structured electrode delivers a capacity of 795 mAh gSn-1 (Sn basis) and 1812 mAh cmel-3 (electrode basis). The long-term cycling shows only 0.04% capacity decay per cycle.

Nanoengineering of 2D tin sulfide nanoflake arrays incorporated on polyaniline nanofibers with boosted capacitive behavior

NASA Astrophysics Data System (ADS)

Wang, Huanhuan; Chao, DongLiang; Liu, Jilei; Lin, Jianyi; Shen, Ze Xiang

2018-07-01

Nanoscale engineering plays an important role in designing novel electrode architecture and boosting energy storage in supercapacitors. Herein, we demonstrate the fabrication of freestanding tin sulfide based supercapacitor electrode using facile nucleation substrate control, i.e. polyaniline network. This is the first time that tin sulfide based material is fabricated as a binder-free electrode for supercapacitors. The first combination of tin sulfide and polyaniline also evokes synergistic effect to enhance the performance as the polyaniline nanofibers facilitate the growth of tin sulfide flakes in nanosize which is further proved helpful for improving the capacity and stability of the electrode. The as-obtained electrode of tin sulfide nanoflake arrays incorporated on polyaniline nanofibers (365 F g‑1 at 10 mV s‑1) exhibits superior electrochemical performance compared with micro-scaled tin sulfide (32 F g‑1 at 10 mV s‑1). The significantly improved pseudocapacitive and diffusive contributions of polyaniline nanofibers incorporated electrode are identified by quantitative kinetics analysis due to greatly decreased particle size and introduced mesopores, nanoclusters, and exposed edges. Profited from effective nanostructure engineering, a Na+ intercalation mechanism is also pointed out in boosting the electrochemical performance.

Study of nickel hydroxide electrodes. 2: Oxidation products of nickel (2) hydroxides

NASA Technical Reports Server (NTRS)

Bode, H.; Demelt, K.; White, J.

1986-01-01

Pure phases of some oxidized Ni oxides were prepared galvanimetrically with the Ni(2) hydroxide electrode of an alkaline battery. The crystallographic data of these phases, their chemical behavior, and conditions of transition were studied.

Fabrication of Highly Ordered and Well-Aligned PbTiO 3/TiN Core–Shell Nanotube Arrays

DOE PAGES

Yoon, Jaesung; Kim, Sangjoon; Kim, Dongjin; ...

2015-04-30

Highly ordered and well-aligned PbTiO 3/TiN core–shell nanotubes are fabricated in this paper via an anodic aluminum oxide templating route followed by TiN and TiO 2 atomic layer deposition deposition and a subsequent PbO vapor reaction. Finally, PbTiO 3/TiN nanotubes keep their original shape after the vapor phase reaction, and they display well-defined piezoresponse hysteresis curves with remnant piezoresponse of 38 pm V -1.

Synthesis of Tetraphenylstannacyclopentadienes (Stannoles). II. Derivatives and Adducts of 1,1-Dihalo-2,3,4,5-tetraphenylstannoles.

DTIC Science & Technology

1981-04-15

products (4-bromo-l,2,3,4-tetraphenylbutadienyl)tin tribromide o (4-iodo-l,2,3,4-tetraphenylbutadienyl)tin triiodide. Even gentle chlorination of...hexaphenyistannole by elemental chlorine cleaves the ring tin-carbon bonds to form cis-cis-l ,4-dichloro-l ,2 ,3 ,4-tetraphenylbutadiene-l, 3 and diphenyltin... chlorination of hexaphenylstannole by elemental chlorine cleaves the ring tin-carbon bonds to form cis- cis-l,4-dichloro-l,2,3,4-tetraphenylbutadiene-1,3

Solderability of pre-tinned Cu sheet

NASA Astrophysics Data System (ADS)

Sunwoo, A. J.; Morris, J. W.; Lucey, G. K.

1992-05-01

The reliability and integrity of pre-tinned copper-clad printed circuit (PC) boards are serious concerns in the manufacture of electronic devices. The factors that influence the wetting during soldering of Cu are discussed. The results suggest that pre-tinning with a Pb-rich solder, such as 95Pb-5Sn, is preferred to pre-tinning with eutectic solder, since the latter can develop exposed intermetallics during aging that wet poorly. The results also confirm that the use of flux leads to carbon contamination in the solder.

System for removal of arsenic from water

DOEpatents

Moore, Robert C.; Anderson, D. Richard

2004-11-23

Systems for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical systems for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A system for continuous removal of arsenic from water is provided. Also provided is a system for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

Layered double hydroxide stability. 1. Relative stabilities of layered double hydroxides and their simple counterparts

NASA Technical Reports Server (NTRS)

Boclair, J. W.; Braterman, P. S.

1999-01-01

Solutions containing di- and trivalent metal chlorides [M(II) = Mg2+, Zn2+, Co2+, Ni2+, Mn2+; M(III) = Al3+, Fe3+] were titrated with NaOH to yield hydrotalcite-like layered double hydroxides (LDH), [[M(II)]1-x[M(III)]x(OH)2][Cl]x yH2O, by way of M(III) hydroxide/hydrous oxide intermediates. Analysis of the resultant titration curves yields nominal solubility constants for the LDH. The corresponding LDH stabilities are in the order Mg < Mn < Co approximately Ni < Zn for M(II) and Al < Fe for M(III). The stability of LDH relative to the separate metal hydroxides/hydrous oxides is discussed.

Conversion coatings prepared or treated with calcium hydroxide solutions

NASA Technical Reports Server (NTRS)

Maxey, Jason (Inventor); Nelson, Carl (Inventor); Eylem, Cahit (Inventor); Minevski, Zoran (Inventor); Clarke, Eric (Inventor)

2002-01-01

A conversion coating process that forms a stable and corrosion-resistant oxide layer on metal or metal oxide substrates or layers. Particularly, the conversion coating process involves contacting the metal or metal oxide substrate or layer with the aqueous calcium hydroxide solutions in order to convert the surface of the substrate to a stable metal oxide layer or coating. According to the present invention, the calcium hydroxide solution is prepared by removing carbon dioxide from water or an aqueous solution before introducing the calcium hydroxide. In this manner, formation of calcium carbonate particles is avoided and the porosity of the conversion coating produced by the calcium hydroxide solution is reduced to below about 1%.

The effect of calcium hydroxide on the steroid component of Ledermix and Odontopaste.

PubMed

Athanassiadis, M; Jacobsen, N; Parashos, P

2011-12-01

To investigate the chemical interaction of calcium hydroxide with the corticosteroid triamcinolone acetonide in Ledermix Paste and in Odontopaste, a new steroid/antibiotic paste. Validated methods were developed to analyse the interaction of calcium hydroxide in two forms, Pulpdent Paste and calcium hydroxide powder, with triamcinolone acetonide within Odontopaste and Ledermix Paste. High-performance liquid chromatography (HPLC) was used to analyse the mixed samples of the pastes and calcium hydroxide. The concentration of triamcinolone acetonide within the pastes was determined over 0, 2, 6, 24 and 72-h time-points. All tests with the HPLC involved the testing of the standard with triplicate injections alongside the samples. All samples were tested in duplicate with each injected twice; therefore, four tests were performed for each investigation. Linearity, precision and specificity of the testing procedures and apparatus were validated. Descriptive statistics are provided. In both pastes, there was a marked rapid destruction of the triamcinolone acetonide steroid upon mixing with calcium hydroxide. Odontopaste suffered a lower rate of destruction of the triamcinolone acetonide component than Ledermix Paste, but both pastes showed very similar degrees of steroid destruction after 72 h. When using calcium hydroxide powder with Ledermix Paste, the triamcinolone was destroyed entirely and immediately. The addition of calcium hydroxide to Odontopaste or Ledermix Paste results in the rapid destruction of the steroid. © 2011 International Endodontic Journal.

Study on improving the heat storage property of Ba(OH)2·8H2O with paraffin

NASA Astrophysics Data System (ADS)

Cui, Kaixuan; Liu, Liqiang; Sun, Mingjie

2017-12-01

Barium hydroxide octahydrate is the crystalline hydration salt with the highest latent heat density within the phase change temperature interval of 0-120 °C and it has a broad application prospect as a phase-change material (PCM). Firstly, red copper test tube was used for the melting—solidification heat cycle experiment in this paper, which was verified by the corrosion experiment of barium hydroxide solution. After the thermogravimetric analysis, it is found that paraffin can effectively reduce the evaporation escape of barium hydroxide octahydrate crystal water within 100 °C. Repeated heat cycle experiments indicated that the paraffin with larger coverage mass fraction can reduce the inhibiting effect of barium hydroxide octahydrate crystal water more obviously. X-ray diffraction analysis indicated that the phase composition of the barium hydroxide octahydrate sample covered with 50 wt% paraffin nearly had no change, while the sample not covered with paraffin has the weight loss ratio of 34.67% and reacted with CO2 in the air, generating BaCO3. In summary, paraffin can not only inhibit the evaporation of crystal water, but also effectively isolate the air to prevent barium hydroxide octahydrate from denaturation. This greatly improved the practicability of barium hydroxide octahydrate as a PCM, laying a good foundation for the further application of barium hydroxide octahydrate.

Layered zinc hydroxide salts: delamination, preferred orientation of hydroxide lamellae, and formation of ZnO nanodiscs.

PubMed

Demel, Jan; Pleštil, Josef; Bezdička, Petr; Janda, Pavel; Klementová, Mariana; Lang, Kamil

2011-08-15

Delamination of layered zinc hydroxide salts (LZH) into hydroxide layers provides nanobuilding blocs of a two-dimensional anisotropy. The methodology, extent of delamination, the size and stability of hydroxide lamellae are described in detail. The ability of lamellae to restack to form oriented hydroxide films depends on the solvent, original LZH salt, and conditions used for delamination. The most interesting results were obtained using LZH intercalated with dodecyl sulfate anions and LZH nitrate delaminated in butanol at 60 °C and in formamide at room temperature, respectively. The former method produces hydroxide lamellae of a lateral size of ca. 10-20 nm. The inner structure of the hydroxide layers is conserved and separated lamellae restack to the original layered structure of LZH dodecyl sulfate. The latter method yields lamellae with a size decreasing from 73.3 nm to 10 nm after a 2-week aging, while their thickness is nearly constant (2.6-3.8 nm). However, the use of formamide is complicated by the formation of Zn(II) formate. The major part of LZH intercalated with dodecyl sulfate anions is transformed during the delamination procedure to anisotropic ZnO nanoparticles, either needle-like particles prolonged in the [0 0 1] direction or disc-like particles flattened along the (0 0 1) plane. Copyright © 2011 Elsevier Inc. All rights reserved.

Effect of Nitrogen Content on Physical and Chemical Properties of TiN Thin Films Prepared by DC Magnetron Sputtering with Supported Discharge

NASA Astrophysics Data System (ADS)

Kavitha, A.; Kannan, R.; Gunasekhar, K. R.; Rajashabala, S.

2017-10-01

Amorphous titanium nitride (TiN) thin films have been prepared on silicon (Si) and glass substrates by direct-current (DC) reactive magnetron sputtering with a supported discharge (triode). Nitrogen gas (N2) at partial pressure of 0.3 Pa, 0.4 Pa, 0.5 Pa, and 0.6 Pa was used to prepare the TiN thin films, maintaining total pressure of argon and N2 of about 0.7 Pa. The chemical, microstructural, optical, and electrical properties of the TiN thin films were systematically studied. Presence of different phases of Ti with nitrogen (N), oxygen (O2), and carbon (C) elements was revealed by x-ray photoelectron spectroscopy characterization. Increase in the nitrogen pressure from 0.3 Pa to 0.6 Pa reduced the optical bandgap of the TiN thin film from 2.9 eV to 2.7 eV. Photoluminescence study showed that TiN thin film deposited at N2 partial pressure of 0.3 Pa exhibited three shoulder peaks at 330 nm, 335 nm, and 340 nm, which disappeared when the sample was deposited with N2 partial pressure of 0.6 Pa. Increase in the nitrogen content decreased the electrical resistivity of the TiN thin film from 3200 μΩ cm to 1800 μΩ cm. Atomic force microscopy studies of the TiN thin films deposited with N2 partial pressure of 0.6 Pa showed a uniform surface pattern associated with accumulation of fine grains. The results and advantages of this method of preparing TiN thin films are also reported.

Tumor-infiltrating Neutrophils is Prognostic and Predictive for Postoperative Adjuvant Chemotherapy Benefit in Patients With Gastric Cancer.

PubMed

Zhang, Heng; Liu, Hao; Shen, Zhenbin; Lin, Chao; Wang, Xuefei; Qin, Jing; Qin, Xinyu; Xu, Jiejie; Sun, Yihong

2018-02-01

This study was aimed to investigate the prognostic value of tumor-infiltrating neutrophils (TINs) and to generate a predictive model to refine postoperative risk stratification system for patients with gastric cancer. TIN presents in various malignant tumors, but its clinical significance in gastric cancer remains obscure. The study enrolled 3 independent sets of patients with gastric cancer from 2 institutional medical centers of China. TIN was estimated by immunohistochemical staining of CD66b, and its relationship with clinicopathological features and clinical outcomes were evaluated. Prognostic accuracies were evaluated by C-index and Akaike information criterion. TINs in gastric cancer tissues ranged from 0 to 192 cells/high magnification filed (HPF), 0 to 117 cells/HPF, and 0 to 142 cells/HPF in the training, testing, and validation sets, respectively. TINs were negatively correlated with lymph node classification (P = 0.007, P = 0.041, and P = 0.032, respectively) and tumor stage (P = 0.019, P = 0.013, and P = 0.025, respectively) in the 3 sets. Moreover, multivariate analysis identified TINs and tumor node metastasis (TNM) stage as 2 independent prognostic factors for overall survival. Incorporation of TINs into well-established TNM system generated a predictive model that shows better predictive accuracy for overall survival. More importantly, patients with higher TINs were prone to overall survival benefit from postoperative adjuvant chemotherapy. These results were validated in the independent testing and validation sets. TIN in gastric cancer was identified as an independent prognostic factor, which could be incorporated into standard TNM staging system to refine risk stratification and predict for overall survival benefit from postoperative chemotherapy in patients with gastric cancer.

Core-shell titanium dioxide-titanium nitride nanotube arrays with near-infrared plasmon resonances

NASA Astrophysics Data System (ADS)

Farsinezhad, Samira; Shanavas, Thariq; Mahdi, Najia; Askar, Abdelrahman M.; Kar, Piyush; Sharma, Himani; Shankar, Karthik

2018-04-01

Titanium nitride (TiN) is a ceramic with high electrical conductivity which in nanoparticle form, exhibits localized surface plasmon resonances (LSPRs) in the visible region of the solar spectrum. The ceramic nature of TiN coupled with its dielectric loss factor being comparable to that of gold, render it attractive for CMOS polarizers, refractory plasmonics, surface-enhanced Raman scattering and a whole host of sensing applications. We report core-shell TiO2-TiN nanotube arrays exhibiting LSPR peaks in the range 775-830 nm achieved by a simple, solution-based, low cost, large area-compatible fabrication route that does not involve laser-writing or lithography. Self-organized, highly ordered TiO2 nanotube arrays were grown by electrochemical anodization of Ti thin films on fluorine-doped tin oxide-coated glass substrates and then conformally coated with a thin layer of TiN using atomic layer deposition. The effects of varying the TiN layer thickness and thermal annealing on the LSPR profiles were also investigated. Modeling the TiO2-TiN core-shell nanotube structure using two different approaches, one employing effective medium approximations coupled with Fresnel coefficients, resulted in calculated optical spectra that closely matched the experimentally measured spectra. Modeling provided the insight that the observed near-infrared resonance was not collective in nature, and was mainly attributable to the longitudinal resonance of annular nanotube-like TiN particles redshifted due to the presence of the higher permittivity TiO2 matrix. The resulting TiO2-TiN core-shell nanotube structures also function as visible light responsive photocatalysts, as evidenced by their photoelectrochemical water-splitting performance under light emitting diode illumination using 400, 430 and 500 nm photons.

Accuracy of iodine removal using dual-energy CT with or without a tin filter: an experimental phantom study.

PubMed

Kawai, Tatsuya; Takeuchi, Mitsuru; Hara, Masaki; Ohashi, Kazuya; Suzuki, Hirochika; Yamada, Kiyotaka; Sugimura, Yuya; Shibamoto, Yuta

2013-10-01

The effects of a tin filter on virtual non-enhanced (VNE) images created by dual-energy CT have not been well evaluated. To compare the accuracy of VNE images between those with and without a tin filter. Two different types of columnar phantoms made of agarose gel were evaluated. Phantom A contained various concentrations of iodine (4.5-1590 HU at 120 kVp). Phantom B consisted of a central component (0, 10, 25, and 40 mgI/cm(3)) and a surrounding component (0, 50, 100, and 200 mgI/cm(3)) with variable iodine concentration. They were scanned by dual-source CT in conventional single-energy mode and dual-energy mode with and without a tin filter. CT values on each gel at the corresponding points were measured and the accuracy of iodine removal was evaluated. On VNE images, the CT number of the gel of Phantom A fell within the range between -15 and +15 HU under 626 and 881 HU at single-energy 120 kVp with and without a tin filter, respectively. With attenuation over these thresholds, iodine concentration of gels was underestimated with the tin filter but overestimated without it. For Phantom B, the mean CT numbers on VNE images in the central gel component surrounded by the gel with iodine concentrations of 0, 50, 100, and 200 mgI/cm(3) were in the range of -19-+6 HU and 21-100 HU with and without the tin filter, respectively. Both with and without a tin filter, iodine removal was accurate under a threshold of iodine concentration. Although a surrounding structure with higher attenuation decreased the accuracy, a tin filter improved the margin of error.

Friction and wear of selected metals and alloys in sliding contact with AISI 440 C stainless steel in liquid methane and in liquid natural gas

NASA Technical Reports Server (NTRS)

Wisander, D. W.

1978-01-01

Aluminum, titanium, beryllium, nickel, iron, copper, and several copper alloys were run in sliding contact with AISI 440C in liquid methane and natural gas. All of the metals run except copper and the copper alloys of tin and tin-lead showed severely galled wear scars. Friction coefficients varied from 0.2 to 1.0, the lowest being for copper, copper-17 wt. % tin, and copper-8 wt. % tin-22 wt. % lead. The wear rate for copper was two orders of magnitude lower than that of the other metals run. An additional order of magnitude of wear reduction was achieved by the addition of tin and/or lead to copper.

Influence of Direct Current Electric Field on Corrosion Behavior of Tin Under a Thin Electrolyte Layer

NASA Astrophysics Data System (ADS)

Huang, H. L.; Bu, F. R.; Tian, J.; Liu, D.

2017-12-01

The influence of a direct current electric field (DCEF) on corrosion behavior of tin under a thin electrolyte layer was investigated based on an array electrode technology by polarization, electrochemical impedance spectroscopy and surface analysis. The experimental results indicate that the corrosion rate of tin near the positive plate of DCEF increases with increased electric field intensity, which could be attributed to the acceleration of the migration of ions, the removal of corrosion products under DCEF and the damage of tin surface oxide film. Furthermore, tin at different positions in a DCEF exhibits different corrosion behavior, which could be ascribed to the difference of the local corrosion environment caused by the DCEF.

Method of manufacturing tin-doped indium oxide nanofibers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozcan, Soydan; Naskar, Amit K

2017-06-06

A method of making indium tin oxide nanofibers includes the step of mixing indium and tin precursor compounds with a binder polymer to form a nanofiber precursor composition. The nanofiber precursor composition is co-formed with a supporting polymer to form a composite nanofiber having a precursor composition nanofiber completely surrounded by the supporting polymer composition. The supporting polymer composition is removed from the composite nanofiber to expose the precursor composition nanofiber. The precursor composition nanofiber is then heated in the presence of oxygen such as O.sub.2 to form indium tin oxide and to remove the binder polymer to form anmore » indium tin oxide nanofiber. A method of making metal oxide nanofibers is also disclosed.« less

Geochemistry of tin in rivers and estuaries

NASA Astrophysics Data System (ADS)

Byrd, James T.; Andreae, Meinrat O.

1986-05-01

On the basis of measurements from a large number of rivers from pristine and polluted regions, we estimate the riverine fluxes of tin to the oceans to be 0.76 × 10 6molyr-1 for the dissolved fraction and 300-600 × 10 6 mol yr -1 for the paniculate fraction. The paniculate flux agrees with the flux calculated from denudation rates. Estuaries were found not to have a large effect upon the transport of tin to the oceans. Evidence for the remobilization of tin was found in an estuary that is highly polluted with tin from mining and smelting activities. Monobutyltin was found to be present in polluted estuaries and is presumed to be a degradation product of tributyltin additives to antifouling paint.

Anodes for alkaline electrolysis

DOEpatents

Soloveichik, Grigorii Lev [Latham, NY

2011-02-01

A method of making an anode for alkaline electrolysis cells includes adsorption of precursor material on a carbonaceous material, conversion of the precursor material to hydroxide form and conversion of precursor material from hydroxide form to oxy-hydroxide form within the alkaline electrolysis cell.

21 CFR 331.11 - Listing of specific active ingredients.

Code of Federal Regulations, 2010 CFR

2010-04-01

... aluminosilicates. (4) Magnesium carbonate. (5) Magnesium glycinate. (6) Magnesium hydroxide. (7) Magnesium oxide..., aluminum hydroxide-magnesium carbonate codried gel, aluminum hydroxide-magnesium trisilicate codried gel... or salt; maximum daily dosage limit 8 grams. (f) Glycine (aminoacetic acid). (g) Magnesium-containing...

21 CFR 331.11 - Listing of specific active ingredients.

Code of Federal Regulations, 2011 CFR

2011-04-01

... aluminosilicates. (4) Magnesium carbonate. (5) Magnesium glycinate. (6) Magnesium hydroxide. (7) Magnesium oxide..., aluminum hydroxide-magnesium carbonate codried gel, aluminum hydroxide-magnesium trisilicate codried gel... or salt; maximum daily dosage limit 8 grams. (f) Glycine (aminoacetic acid). (g) Magnesium-containing...

42 CFR 425.304 - Other program requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... interests in the judgment of the referring party. (d) Required reporting of NPIs and TINs. (1) The ACO must... times as specified by CMS the list of each ACO participant's TIN and ACO providers/supplier's NPI that... any changes to the list of NPIs and TINs. ...

42 CFR 425.304 - Other program requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... interests in the judgment of the referring party. (d) Required reporting of NPIs and TINs. (1) The ACO must... times as specified by CMS the list of each ACO participant's TIN and ACO providers/supplier's NPI that... any changes to the list of NPIs and TINs. ...

26 CFR 301.6721-0 - Table of Contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... TINs. (1) In general. (i) Initial solicitation. (ii) First annual solicitation. (iii) Second annual.... (f) Acting in a responsible manner—special rules for incorrect TINs. (1) In general. (i) Initial...) In general. (2) Special rules relating to TINs. (3) Effective dates. (h) Transitional rules for...

26 CFR 301.6721-0 - Table of Contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TINs. (1) In general. (i) Initial solicitation. (ii) First annual solicitation. (iii) Second annual.... (f) Acting in a responsible manner—special rules for incorrect TINs. (1) In general. (i) Initial...) In general. (2) Special rules relating to TINs. (3) Effective dates. (h) Transitional rules for...

78 FR 16832 - Corrosion-Resistant Carbon Steel Flat Products From Germany and the Republic of Korea: Revocation...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-19

.... Excluded from the scope of the orders are flat-rolled steel products either plated or coated with tin, lead, chromium, chromium oxides, both tin and lead (``terne plate''), or both chromium and chromium oxides (``tin...

42 CFR 425.304 - Other program requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... interests in the judgment of the referring party. (d) Required reporting of NPIs and TINs. (1) The ACO must... times as specified by CMS the list of each ACO participant's TIN and ACO providers/supplier's NPI that... any changes to the list of NPIs and TINs. ...

Facile Synthesis of Wormhole-Like Mesoporous Tin Oxide via Evaporation-Induced Self-Assembly and the Enhanced Gas-Sensing Properties

NASA Astrophysics Data System (ADS)

Li, Xiaoyu; Peng, Kang; Dou, Yewei; Chen, Jiasheng; Zhang, Yue; An, Gai

2018-01-01

Wormhole-like mesoporous tin oxide was synthesized via a facile evaporation-induced self-assembly (EISA) method, and the gas-sensing properties were evaluated for different target gases. The effect of calcination temperature on gas-sensing properties of mesoporous tin oxide was investigated. The results demonstrate that the mesoporous tin oxide sensor calcined at 400 °C exhibits remarkable selectivity to ethanol vapors comparison with other target gases and has a good performance in the operating temperature and response/recovery time. This might be attributed to their high specific surface area and porous structure, which can provide more active sites and generate more chemisorbed oxygen spices to promote the diffusion and adsorption of gas molecules on the surface of the gas-sensing material. A possible formation mechanism of the mesoporous tin oxide and the enhanced gas-sensing mechanism are proposed. The mesoporous tin oxide shows prospective detecting application in the gas sensor fields.

Nature of active tin species and promoting effect of nickle in silica supported tin oxide for dehydrogenation of propane

NASA Astrophysics Data System (ADS)

Wang, Haoren; Wang, Hui; Li, Xiuyi; Li, Chunyi

2017-06-01

Different with Wang et. al.'s study, we found that polymeric Si-O-Sn2+ rather than Ni-Sn alloy and metallic Sn are active species in silica-supported tin oxide catalysts for dehydrogenation of propane. The results showed that high surface area of mesoporous silica brought about high dispersion of tin oxide species, as a result, catalytic activity and stability were both improved. DRUV-vis, XPS, TPR and XRD studies of fresh and reduced catalysts indicated that the deactivation was related to the reduction of active species rather than the coke formation since active tin species cannot maintain its oxidation state at reaction conditions (high temperature and reducing atmosphere). The formed Ni3Sn2 alloy after reduction just functioned as promoter which accelerated the desorption of H2 and regeneration of active site. A synergy effect between active tin species and Ni3Sn2 alloy were observed.

Potential of tin (IV) chloride for treatment in Alor Pongsu as stabilized landfill leachate

NASA Astrophysics Data System (ADS)

Zainal, Sharifah Farah Fariza Syed; Aziz, Hamidi Abdul

2017-10-01

Leachate production from landfilling contributes crucial pollutants to the environment. This study examined the potential of tin (IV) chloride as coagulant that involved charge neutralization and sweep flocculation mechanisms. The negative charge of leachate is neutralized by adding tin (IV) chloride as cationic coagulant which resulted precipitation and swept most of the colloids and dissolved solids that entrapped in the settling as hydrous oxide floc. Parameters such as suspended solid (SS) content, color, and chemical oxygen demand (COD) were analyzed using standard jar test procedures. The best condition was observed at pH 8, with removal efficiencies of 75.99 %, 99.29 % and 98.36 % for COD, SS, and color, respectively. At optimum dosage, tin (IV) chloride successfully removed 98.40 % for color, 99.54 % for SS and 71.53 % for COD. These results indicated the satisfactory performance of tin (IV) chloride. Hence, tin (IV) chloride is a potential coagulant for the treatment of Alor Pongsu Landfill leachate.

Dopant-Free Tetrakis-Triphenylamine Hole Transporting Material for Efficient Tin-Based Perovskite Solar Cells.

PubMed

Ke, Weijun; Priyanka, Pragya; Vegiraju, Sureshraju; Stoumpos, Constantinos C; Spanopoulos, Ioannis; Soe, Chan Myae Myae; Marks, Tobin J; Chen, Ming-Chou; Kanatzidis, Mercouri G

2018-01-10

Developing dopant-free hole transporting layers (HTLs) is critical in achieving high-performance and robust state-of-the-art perovskite photovoltaics, especially for the air-sensitive tin-based perovskite systems. The commonly used HTLs require hygroscopic dopants and additives for optimal performance, which adds extra cost to manufacturing and limits long-term device stability. Here we demonstrate the use of a novel tetrakis-triphenylamine (TPE) small molecule prepared by a facile synthetic route as a superior dopant-free HTL for lead-free tin-based perovskite solar cells. The best-performing tin iodide perovskite cells employing the novel mixed-cation ethylenediammonium/formamidinium with the dopant-free TPE HTL achieve a power conversion efficiency as high as 7.23%, ascribed to the HTL's suitable band alignment and excellent hole extraction/collection properties. This efficiency is one of the highest reported so far for tin halide perovskite systems, highlighting potential application of TPE HTL material in low-cost high-performance tin-based perovskite solar cells.

Pretreatment of poly(l-lactide-co-glycolide) scaffolds with sodium hydroxide enhances osteoblastic differentiation and slows proliferation of mouse preosteoblast cells.

PubMed

Carpizo, Katherine H; Saran, Madeleine J; Huang, Weibiao; Ishida, Kenji; Roostaeian, Jason; Bischoff, David; Huang, Catherine K; Rudkin, George H; Yamaguchi, Dean T; Miller, Timothy A

2008-02-01

Surface topography is important in the creation of a scaffold for tissue engineering. Chemical etching of poly(l-lactide-co-glycolide) with sodium hydroxide has been shown to enhance adhesion and function of numerous cell types. The authors investigated the effects of sodium hydroxide pretreatment of three-dimensional poly(l-lactide-co-glycolide) scaffolds on the adhesion, differentiation, and proliferation of MC3T3-E1 murine preosteoblasts. MC3T3-E1 cells were seeded onto three-dimensional poly(l-lactide-co-glycolide) scaffolds with and without 1 M sodium hydroxide pretreatment. Cells were then cultured in osteogenic medium and harvested at varying time points for RNA extraction. Quantitative real-time reverse-transcriptase polymerase chain reaction was performed to measure mRNA expression of several osteogenic marker genes. In addition, cell numbers were determined at varying time points during the culture period. All experiments were performed in triplicate. Pretreatment of three-dimensional poly(l-lactide-co-glycolide) scaffolds with sodium hydroxide resulted in statistically significant up-regulation of mRNA expression of alkaline phosphatase, bone sialoprotein, osteocalcin, and vascular endothelial growth factor during the first 10 days of culture. Histologic analysis demonstrated a striking increase in mineralized cell matrix deposition in the sodium hydroxide-treated group. Cell number was statistically higher in the sodium hydroxide-treated group immediately after cell seeding, suggesting improved adhesion. During the first 24 hours of culture, cells grew faster in the control group than in the sodium hydroxide-treated group. Chemical etching of poly(l-lactide-co-glycolide) scaffolds with sodium hydroxide strongly influences the behavior of MC3T3-E1 preosteoblasts in vitro by enhancing adhesion and differentiation and slowing proliferation. Sodium hydroxide treatment may represent a simple and inexpensive way of improving scaffolds for use in bone tissue engineering.

Structural Differentiation between Layered Single (Ni) and Double Metal Hydroxides (Ni–Al LDHs) Using Wavelet Transformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siebecker, Matthew G.; Sparks, Donald L.

2017-09-07

Layered double hydroxides (LDHs) are anionic clays important in disciplines such as environmental chemistry, geochemistry, and materials science. Developments in signal processing of extended X-ray absorption fine structure (EXAFS) data, such as wavelet transformation (WT), have been used to identify transition metals and Al present in the hydroxide sheets of LDHs. The WT plots of LDHs should be distinct from those of isostructural single metal hydroxides. However, no direct comparison of these minerals appears in the literature using WT. This work systematically analyzes a suite of Ni-rich mineral standards, including Ni–Al LDHs, single metal Ni hydroxides, and Ni-rich silicates usingmore » WT. The results illustrate that the WT plots for α-Ni(OH)2 and Ni–Al LDHs are often indistinguishable from each other, with similar two-component plots for the different mineral types. This demonstrates that the WT of the first metal shell often cannot be used to differentiate an LDH from a single metal hydroxide. Interlayer anions adsorbed to the hydroxide sheet of α-Ni(OH)2 affect the EXAFS spectra and are not visible in the FT but are clearly resolved and discrete in the WT.« less

Chemical matricectomy with sodium hydroxide: long-term follow-up results.

PubMed

Bostanci, Seher; Kocyigit, Pelin; Parlak, Nehir; Gungor, Hilayda Karakok

2014-11-01

Chemical matricectomy with sodium hydroxide is a method being used successfully in the treatment of ingrown toenail. In this study, it was aimed to evaluate long-term recurrence rates after chemical matricectomy using sodium hydroxide application of different durations. Two hundred two patients with ingrown nail edges were treated with either 1-minute (Group 1) or 2-minute (Group 2) applications of sodium hydroxide matricectomy. All patients were followed for at least 2 years. Chemical matricectomy with sodium hydroxide was applied to a total of 585 nail edges of 202 cases. The overall recurrence rates in Group 1 and Group 2 were 6.4% and 7.1%, respectively, during the average 7.5-year follow-up period. No statistically significant differences were detected in terms of recurrence between the 2 groups (p = .73). Chemical matricectomy with sodium hydroxide is an easy method in the treatment of ingrown nails, with low morbidity and high success rates. There was no difference between 1-minute and 2-minute applications in terms of recurrence during the long-term follow-up. Chemical matricectomy with 1-minute application of sodium hydroxide showed high success in terms of long-term follow-up results.

Determination of total tin in silicate rocks by graphite furnace atomic absorption spectrometry

USGS Publications Warehouse

Elsheimer, H.N.; Fries, T.L.

1990-01-01

A method is described for the determination of total tin in silicate rocks utilizing a graphite furnace atomic absorption spectrometer with a stabilized-temperature platform furnace and Zeeman-effect background correction. The sample is decomposed by lithium metaborate fusion (3 + 1) in graphite crucibles with the melt being dissolved in 7.5% hydrochloric acid. Tin extractions (4 + 1 or 8 + 1) are executed on portions of the acid solutions using a 4% solution of tricotylphosphine oxide in methyl isobutyl ketone (MIBK). Ascorbic acid is added as a reducing agent prior to extraction. A solution of diammonium hydrogenphosphate and magnesium nitrate is used as a matrix modifier in the graphite furnace determination. The limit of detection is > 10 pg, equivalent to > 1 ??g l-1 of tin in the MIBK solution or 0.2-0.3 ??g g-61 in the rock. The concentration range is linear between 2.5 and 500 ??g l-1 tin in solution. The precision, measured as relative standard deviation, is < 20% at the 2.5 ??g l-1 level and < 7% at the 10-30 ??g l-1 level of tin. Excellent agreement with recommended literature values was found when the method was applied to the international silicate rock standards BCR-1, PCC-1, GSP-1, AGV-1, STM-1, JGb-1 and Mica-Fe. Application was made to the determination of tin in geological core samples with total tin concentrations of the order of 1 ??g g-1 or less.

Alkali Silicate Glass Coatings for Mitigating the Risks of Tin Whiskers

NASA Astrophysics Data System (ADS)

Hillman, Dave; Wilcoxon, Ross; Lower, Nate; Grossman, Dan

2015-12-01

Alkali silicate glass (ASG) coatings were investigated as a possible method for inhibiting tin whisker initiation and growth. The aqueous-based ASG formulations used in this study were deposited with equipment and conditions that are typical of those used to apply conventional conformal coatings. Processes for controlling ASG coating properties were developed, and a number of ASG-based coating combinations were applied to test components with pure tin surfaces. Coatings were applied both in a laboratory environment at Rockwell Collins and in a manufacturing environment at Plasma Ruggedized Solutions. Testing in elevated humidity/temperature environments and subsequent inspection of the test articles identified coating combinations that inhibited tin whisker growth as well as other material combinations that actually accelerated tin whisker growth. None of the coatings evaluated in this study, including conventional acrylic and Parylene conformal coatings, completely prevented the formation of tin whiskers. Two of the coatings were particularly effective at reducing the risks of whisker growth, albeit through different mechanisms. Parylene conformal coating almost, but not completely, eliminated whisker formation, and only a few tin whiskers were found on these surfaces during the study. A composite of ASG and alumina nanoparticles inhibited whisker formation to a lesser degree than Parylene, but did disrupt whisker growth mechanisms so as to inhibit the formation of long, and more dangerous, tin whiskers. Additional testing also demonstrated that the conformal coatings had relatively little effect on the dielectric loss of a stripline test structure operating at frequencies over 30 GHz.

Method of determining pH by the alkaline absorption of carbon dioxide

DOEpatents

Hobbs, David T.

1992-01-01

A method for measuring the concentration of hydroxides in alkaline solutions in a remote location using the tendency of hydroxides to absorb carbon dioxide. The method includes the passing of carbon dioxide over the surface of an alkaline solution in a remote tank before and after measurements of the carbon dioxide solution. A comparison of the measurements yields the absorption fraction from which the hydroxide concentration can be calculated using a correlation of hydroxide or pH to absorption fraction.

Method of treating inflammatory diseases using a radiolabeled ferric hydroxide calloid

DOEpatents

Atcher, Robert W.; Hines, John J.

1992-01-01

A ferric hydroxide colloid having an alpha-emitting radionuclide essentially on the outer surfaces and a method of forming same. The method includes oxidizing a ferrous hydroxide to ferric hydroxide in the presence of a preselected radionuclide to form a colloid having the radionuclide on the outer surface thereof, and thereafter washing the colloid, and suspending the washed colloid in a suitable solution. The labelled colloid is useful in cancer therapy and for the treatment of inflamed joints.

Nickel hydroxide/cobalt-ferrite magnetic nanocatalyst for alcohol oxidation.

PubMed

Bhat, Pooja B; Inam, Fawad; Bhat, Badekai Ramachandra

2014-08-11

A magnetically separable, active nickel hydroxide (Brønsted base) coated nanocobalt ferrite catalyst has been developed for oxidation of alcohols. High surface area was achieved by tuning the particle size with surfactant. The surface area of 120.94 m2 g(-1) has been achieved for the coated nanocobalt ferrite. Improved catalytic activity and selectivity were obtained by synergistic effect of transition metal hydroxide (basic hydroxide) on nanocobalt ferrite. The nanocatalyst oxidizes primary and secondary alcohols efficiently (87%) to corresponding carbonyls in good yields.

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

40 CFR 471.13 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS FORMING AND METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth...-tin-bismuth forming operations' process wastewater shall not exceed the following values: (a) Rolling... monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with emulsions...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 471.13 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS FORMING AND METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth...-tin-bismuth forming operations' process wastewater shall not exceed the following values: (a) Rolling... monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with emulsions...

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

NASA Technical Reports Server (NTRS)

Otterson, Dumas A.

1961-01-01

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

The effects of lithium hydroxide solution on alkali silica reaction gels created with opal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Lyndon D.; Beaudoin, James J.; Grattan-Bellew, Patrick

The reaction of Nevada opal with calcium hydroxide, potassium hydroxide and lithium hydroxide solutions was investigated. In addition, opal was exposed to a combined solution of these three hydroxides. The progress of the three reactions was followed using X-ray diffraction (XRD), {sup 29}Si nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). The XRD results indicated the presence of a low-angle peak exclusive to the lithium-based reactions. The NMR results suggested a change in the silicate structure in the presence of lithium. These techniques indicated that the reaction of the alkali with the opal starting material is inhibited and perhapsmore » stopped in the presence of lithium hydroxide. SEM revealed that the morphology of the reaction products on the surface of the reacted opal grains is markedly different invariably. It was concluded that evidence to support the theory of a protective layer exists and that the nature of the layer varies with ion type.« less

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

PubMed Central

Nakayama, Hirokazu; Hayashi, Aki

2014-01-01

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids. PMID:25080007

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition.

PubMed

Nakayama, Hirokazu; Hayashi, Aki

2014-07-30

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

Associating cooking additives with sodium hydroxide to pretreat bamboo residues for improving the enzymatic saccharification and monosaccharides production.

PubMed

Huang, Caoxing; He, Juan; Wang, Yan; Min, Douyong; Yong, Qiang

2015-10-01

Cooking additive pulping technique is used in kraft mill to increase delignification degree and pulp yield. In this work, cooking additives were firstly applied in the sodium hydroxide pretreatment for improving the bioconversion of bamboo residues to monosaccharides. Meanwhile, steam explosion and sulfuric acid pretreatments were also carried out on the sample to compare their impacts on monosaccharides production. Results indicated that associating anthraquinone with sodium hydroxide pretreatment showed the best performance in improving the original carbohydrates recovery, delignification, enzymatic saccharification, and monosaccharides production. After consecutive pretreatment and enzymatic saccharification process, 347.49 g, 307.48 g, 142.93 g, and 87.15 g of monosaccharides were released from 1000 g dry bamboo residues pretreated by sodium hydroxide associating with anthraquinone, sodium hydroxide, steam explosion and sulfuric acid, respectively. The results suggested that associating cooking additive with sodium hydroxide is an effective pretreatment for bamboo residues to enhance enzymatic saccharification for monosaccharides production. Copyright © 2015 Elsevier Ltd. All rights reserved.

Reversible storage of lithium in a rambutan-like tin-carbon electrode.

PubMed

Deng, Da; Lee, Jim Yang

2009-01-01

Fruity electrodes: A simple bottom-up self-assembly method was used to fabricate rambutan-like tin-carbon (Sn@C) nanoarchitecture (see scheme, green Sn) to improve the reversible storage of lithium in tin. The mechanism of the growth of the pear-like hairs is explored.

48 CFR 4.203 - Taxpayer identification information.

Code of Federal Regulations, 2010 CFR

2010-10-01

... furnished a Taxpayer Identification Number (TIN) when completing the solicitation provision at 52.204-3... the contract sent to the payment office. (b) If the TIN or type of organization is derived from a... last page of the contract or order forwarded to the payment office to state the contractor's TIN and...

48 CFR 4.902 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) requires each contractor doing business with a Government agency to furnish its TIN to that agency. 31 U.S... Government payment office and submitted to a disbursing official, the TIN of the contractor receiving payment under the voucher. The TIN may be used by the Government to collect and report on any delinquent amounts...

26 CFR 301.6724-1 - Reasonable cause.

Code of Federal Regulations, 2014 CFR

2014-04-01

... waiver where the filer's failure relates to a taxpayer identification number (TIN), and the failure is... incorrect TIN will be deemed to have acted in a responsible manner in compliance with this paragraph (d) only if the filer satisfies the requirements of paragraph (e) of this section (relating to missing TINs...

31 CFR 359.31 - What definitive Series I savings bonds are included in the computation?

Code of Federal Regulations, 2011 CFR

2011-07-01

... registered in the name of and bearing the taxpayer identification number (TIN) of that person alone or as co... bearing that person's TIN; and (c) All gift bonds registered in the name of that person but bearing the TIN of the purchaser. ...

40 CFR 471.14 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.14 Pretreatment standards for existing sources (PSES... in lead-tin-bismuth forming process wastewater introduced into a POTW shall not exceed the following... Maximum for monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with...

47 CFR 1.923 - Content of applications.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (TINs). Wireless applicants and licensees, including all attributable owners of auctionable licenses as defined by § 1.2112 of this part, are required to provide their Taxpayer Identification Numbers (TINS) (as... (DCIA). Under the DCIA, the FCC may use an applicant or licensee's TIN for purposes of collecting and...

40 CFR 471.14 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Tin-Bismuth Forming Subcategory § 471.14 Pretreatment standards for existing sources (PSES). Except as...-tin-bismuth forming process wastewater introduced into a POTW shall not exceed the following values... Maximum for monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with...

48 CFR 4.902 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) requires each contractor doing business with a Government agency to furnish its TIN to that agency. 31 U.S... Government payment office and submitted to a disbursing official, the TIN of the contractor receiving payment under the voucher. The TIN may be used by the Government to collect and report on any delinquent amounts...

78 FR 70102 - Advisory Committee to the Internal Revenue Service; Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-22

...)--additional addresses; Missing TINS for Employer and Insurer Reporting; Minimum Essential Coverage, Premium... (TIN) Matching Program to Improve the Accuracy of Information Reporting; IRC Sec. 6050W and Form 1099-K Reporting; Taxpayer Identification Number (TIN) Truncation; Stripped Tax Credits; Form 1098-T; Form 8300...

48 CFR 2152.204-70 - Taxpayer Identification Number.

Code of Federal Regulations, 2014 CFR

2014-10-01

... basis, and of which the Contractor is a member. Taxpayer Identification Number (TIN), as used in this... reporting income tax and other returns. The TIN is the Contractor's Social Security Number. (b) The... information will result in payment being withheld until the TIN is provided. (c) The Government may use the...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2012 CFR

2012-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

48 CFR 4.203 - Taxpayer identification information.

Code of Federal Regulations, 2011 CFR

2011-10-01

... furnished a Taxpayer Identification Number (TIN) when completing the solicitation provision at 52.204-3... the contract sent to the payment office. (b) If the TIN or type of organization is derived from a... last page of the contract or order forwarded to the payment office to state the contractor's TIN and...

47 CFR 1.923 - Content of applications.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Identification Number (TINs). Wireless applicants and licensees, including all attributable owners of auctionable... (TINS) (as defined in 26 U.S.C. 6109) to the Commission, pursuant to the Debt Collection Improvement Act of 1996 (DCIA). Under the DCIA, the FCC may use an applicant or licensee's TIN for purposes of...

48 CFR 4.902 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) requires each contractor doing business with a Government agency to furnish its TIN to that agency. 31 U.S... Government payment office and submitted to a disbursing official, the TIN of the contractor receiving payment under the voucher. The TIN may be used by the Government to collect and report on any delinquent amounts...

40 CFR 471.13 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Tin-Bismuth Forming Subcategory § 471.13 New source performance standards (NSPS). Any new source... pollutants in the lead-tin-bismuth forming operations' process wastewater shall not exceed the following... Maximum for monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with...

42 CFR 414.1205 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... physicians means a single Tax Identification Number (TIN) with 2 or more eligible professionals, as... rights to the TIN. Performance period means the calendar year that will be used to assess the quality of...) model. Taxpayer Identification Number (TIN) has the same meaning given this term under § 425.20 of this...

40 CFR 471.14 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.14 Pretreatment standards for existing sources (PSES... in lead-tin-bismuth forming process wastewater introduced into a POTW shall not exceed the following... Maximum for monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with...

40 CFR 471.13 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-Tin-Bismuth Forming Subcategory § 471.13 New source performance standards (NSPS). Any new source... pollutants in the lead-tin-bismuth forming operations' process wastewater shall not exceed the following... Maximum for monthly average mg/off-kg (pounds per million off-pounds) of lead-tin-bismuth rolled with...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2010 CFR

2010-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...