tool rake face: Topics by Science.gov

Sample records for tool rake face

Orthogonal cutting of cancellous bone with application to the harvesting of bone autograft.

PubMed

Malak, Sharif F F; Anderson, Iain A

2008-07-01

Autogenous bone graft harvesting results in cell death within the graft and trauma at the donor site. The latter can be mitigated by using minimally invasive tools and techniques, while cell morbidity may be reduced by improving cutter design and cutting parameters. We have performed orthogonal cutting experiments on bovine cancellous bone samples, to gain a basic understanding of the cutting mechanism and to determine design guidelines for tooling. Measurements were performed at cutting speeds from 11.2 to 5000 mm/min, with tool rake angles of 23 degrees, 45 degrees and 60 degrees, and depths of cut in the range of 0.1-3.0 mm. Horizontal and vertical cutting forces were measured, and the chip formation process video recorded. Continuous chip formation was observed for rake angles of 45 degrees and 60 degrees , and depths of cut greater than 0.8 mm. Chip formation for depths of cut greater than 1.0 mm was accompanied by bone marrow extruding out of the free surfaces and away from the rake face. Specific cutting energies decreased with increasing rake angle, increasing depth of cut and increasing cutting speed. Our orthogonal cutting experiments showed that a rake angle of 60 degrees and a depth of cut of 1mm, will avoid excessive fragmentation, keep specific cutting energy low and promote bone marrow extrusion, which may be beneficial for cell survival. We demonstrate how drill bit clearance angle and feed rate can be calculated facilitating a 1mm depth of cut.
Raking it in: the impact of enculturation on chimpanzee tool use.

PubMed

Furlong, E E; Boose, K J; Boysen, S T

2008-01-01

Recent evidence for different tool kits, proposed to be based upon culture-like transmission, have been observed across different chimpanzee communities across Western Africa. In light of these findings, the reported failures by seven captive juvenile chimpanzees tested with 27 tool use tasks (Povinelli 2000) seem enigmatic. Here we report successful performance by a group of nine captive, enculturated chimpanzees, and limited success by a group of six semi-enculturated chimpanzees, on two of the Povinelli tasks, the Flimsy Tool task, and the Hybrid Tool task. All chimpanzees were presented with a rake with a flimsy head and a second rake with a rigid head, either of which could be used to attempt to retrieve a food reward that was out of reach. The rigid rake was constructed such that it had the necessary functional features to permit successful retrieval, while the flimsy rake did not. Both chimpanzee groups in the present experiment selected the functional rigid tool correctly to use during the Flimsy Tool task. All animals were then presented with two "hybrid rakes" A and B, with one half of each rake head constructed from flimsy, non-functional fabric, and the other half of the head was made of wood. Food rewards were placed in front of the rigid side of Rake A and the flimsy side of Rake B. To be successful, the chimps needed to choose the rake that had the reward in front of the rigid side of the rake head. The fully enculturated animals were successful in selecting the functional rake, while the semi-enculturated subjects chose randomly between the two hybrid tools. Compared with findings from Povinelli, whose non-enculturated animals failed both tasks, our results demonstrate that chimpanzees reared under conditions of semi-enculturation could learn to discriminate correctly the necessary tool through trial-and-error during the Flimsy Tool task, but were unable to recognize the functional relationship necessary for retrieving the reward with the "hybrid" rake. In contrast, the enculturated chimpanzees were correct in their choices during both the Flimsy Tool and the Hybrid Tool tasks. These results provide the first empirical evidence for the differential effects of enculturation on subsequent tool use capacities in captive chimpanzees.
Design and flight testing of a nullable compressor face rake

NASA Technical Reports Server (NTRS)

Holzman, J. K.; Payne, G. A.

1973-01-01

A compressor face rake with an internal valve arrangement to permit nulling was designed, constructed, and tested in the laboratory and in flight at the NASA Flight Research Center. When actuated by the pilot in flight, the nullable rake allowed the transducer zero shifts to be determined and then subsequently removed during data reduction. Design details, the fabrication technique, the principle of operation, brief descriptions of associated digital zero-correction programs and the qualification tests, and test results are included. Sample flight data show that the zero shifts were large and unpredictable but could be measured in flight with the rake. The rake functioned reliably and as expected during 25 hours of operation under flight environmental conditions and temperatures from 230 K (-46 F) to greater than 430 K (314 F). The rake was nulled approximately 1000 times. The in-flight zero-shift measurement technique, as well as the rake design, was successful and should be useful in future applications, particularly where accurate measurements of both steady-state and dynamic pressures are required under adverse environmental conditions.
Investigating bone chip formation in craniotomy.

PubMed

Huiyu, He; Chengyong, Wang; Yue, Zhang; Yanbin, Zheng; Linlin, Xu; Guoneng, Xie; Danna, Zhao; Bin, Chen; Haoan, Chen

2017-10-01

In a craniotomy, the milling cutter is one of the most important cutting tools. The operating performance, tool durability and cutting damage to patients are influenced by the tool's sharpness, intensity and structure, whereas the cutting characteristics rely on interactions between the tool and the skull. In this study, an orthogonal cutting experiment during a craniotomy of fresh pig skulls was performed to investigate chip formation on the side cutting and face cutting of the skull using a high-speed camera. The cutting forces with different combinations of cutting parameters, such as the rake angle, clearance angle, depth of cut and cutting speed, were measured. The skull bone microstructure and cutting damage were observed by scanning electron microscope. Cutting models for different cutting approaches and various depths of cut were constructed and analyzed. The study demonstrated that the effects of shearing, tension and extrusion occur during chip formation. Various chip types, such as unit chips, splintering chips and continuous chips, were generated. Continuous pieces of chips, which are advisable for easy removal from the field of operation, were formed at greater depths of cut and tool rake angles greater than 10°. Cutting damage could be relieved with a faster recovery with clearance angles greater than 20°.
Effect of micro-scale texturing on the cutting tool performance

NASA Astrophysics Data System (ADS)

Vasumathy, D.; Meena, Anil

2018-05-01

The present study is mainly focused on the cutting performance of the micro-scale textured carbide tools while turning AISI 304 austenitic stainless steel under dry cutting environment. The texture on the rake face of the carbide tools was fabricated by laser machining. The cutting performance of the textured tools was further compared with conventional tools in terms of cutting forces, tool wear, machined surface quality and chip curl radius. SEM and EDS analyses have been also performed to better understand the tool surface characteristics. Results show that the grooves help in breaking the tool-chip contact leading to a lesser tool-chip contact area which results in reduced iron (Fe) adhesion to the tool.
Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G.

2011-01-17

The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasivemore » and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.« less
Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

NASA Astrophysics Data System (ADS)

Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G.

2011-01-01

The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasive and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.
Investigations on the Effect of Steady and Pulsed Surface. Thermal Perturbations on the Hypersonic Flow-Field Over a Flat Plate and a Sharp Cone

DTIC Science & Technology

2010-03-10

achieved by setting proper driver and driven pressures. A calibration of the tunnel was done for the decided freestream conditions with a pitot rake ...measurement. A rake of 12 pitot probes spanning the diameter of the nozzle (300 mm) was placed facing the freestream. The pitot pressures were... pitot rake and shock tube measurements, the freestream conditions for each of the observed rupture pressure are estimated. It was observed that of
Influence of Surface Features for Increased Heat Dissipation on Tool Wear

PubMed Central

Beno, Tomas; Hoier, Philipp; Wretland, Anders

2018-01-01

The critical problems faced during the machining process of heat resistant superalloys, (HRSA), is the concentration of heat in the cutting zone and the difficulty in dissipating it. The concentrated heat in the cutting zone has a negative influence on the tool life and surface quality of the machined surface, which in turn, contributes to higher manufacturing costs. This paper investigates improved heat dissipation from the cutting zone on the tool wear through surface features on the cutting tools. Firstly, the objective was to increase the available surface area in high temperature regions of the cutting tool. Secondly, multiple surface features were fabricated for the purpose of acting as channels in the rake face to create better access for the coolant to the proximity of the cutting edge. The purpose was thereby to improve the cooling of the cutting edge itself, which exhibits the highest temperature during machining. These modified inserts were experimentally investigated in face turning of Alloy 718 with high-pressure coolant. Overall results exhibited that surface featured inserts decreased flank wear, abrasion of the flank face, cutting edge deterioration and crater wear probably due to better heat dissipation from the cutting zone. PMID:29693579
On the closed form mechanistic modeling of milling: Specific cutting energy, torque, and power

NASA Astrophysics Data System (ADS)

Bayoumi, A. E.; Yücesan, G.; Hutton, D. V.

1994-02-01

Specific energy in metal cutting, defined as the energy expended in removing a unit volume of workpiece material, is formulated and determined using a previously developed closed form mechanistic force model for milling operations. Cutting power is computed from the cutting torque, cutting force, kinematics of the cutter, and the volumetric material removal rate. Closed form expressions for specific cutting energy were formulated and found to be functions of the process parameters: pressure and friction for both rake and flank surfaces and chip flow angle at the rake face of the tool. Friction is found to play a very important role in cutting torque and power. Experiments were carried out to determine the effects of feedrate, cutting speed, workpiece material, and flank wear land width on specific cutting energy. It was found that the specific cutting energy increases with a decrease in the chip thickness and with an increase in flank wear land.
2D simulations of orthogonal cutting of CFRP: Effect of tool angles on parameters of cut and chip morphology

NASA Astrophysics Data System (ADS)

Benhassine, Mehdi; Rivière-Lorphèvre, Edouard; Arrazola, Pedro-Jose; Gobin, Pierre; Dumas, David; Madhavan, Vinay; Aizpuru, Ohian; Ducobu, François

2018-05-01

Carbon-fiber reinforced composites (CFRP) are attractive materials for lightweight designs in applications needing good mechanical properties. Machining of such materials can be harder than metals due to their anisotropic behavior. In addition, the combination of the fibers and resin mechanical properties must also include the fiber orientation. In the case of orthogonal cutting, the tool inclination, rake angle or cutting angle usually influence the cutting process but such a detailed investigation is currently lacking in a 2D configuration. To address this issue, a model has been developed with Abaqus Explicit including Hashin damage. This model has been validated with experimental results from the literature. The effects of the tool parameters (rake angle, clearance angle) on the tool cutting forces, CFRP chip morphology and surface damage are herewith studied. It is shown that 90° orientation for the CFRP increases the surface damage. The rake angle has a minimal effect on the cutting forces but modifies the chip formation times. The feed forces are increased with increasing rake angle.
Effect of number of probes and their orientation on the calculation of several compressor face distortion descriptors

NASA Technical Reports Server (NTRS)

Stoll, F.; Tremback, J. W.; Arnaiz, H. H.

1979-01-01

A study was performed to determine the effects of the number and position of total pressure probes on the calculation of five compressor face distortion descriptors. This study used three sets of 320 steady state total pressure measurements that were obtained with a special rotating rake apparatus in wind tunnel tests of a mixed-compression inlet. The inlet was a one third scale model of the inlet on a YF-12 airplane, and it was tested in the wind tunnel at representative flight conditions at Mach numbers above 2.0. The study shows that large errors resulted in the calculation of the distortion descriptors even with a number of probes that were considered adequate in the past. There were errors as large as 30 and -50 percent in several distortion descriptors for a configuration consisting of eight rakes with five equal-area-weighted probes on each rake.
An analytical method on the surface residual stress for the cutting tool orientation

NASA Astrophysics Data System (ADS)

Li, Yueen; Zhao, Jun; Wang, Wei

2010-03-01

The residual stress is measured by choosing 8 kinds orientations on cutting the H13 dies steel on the HSM in the experiment of this paper. The measured data shows on that the residual stress exists periodicity for the different rake angle (β) and side rake angle (θ) parameters, further study find that the cutting tool orientations have closed relationship with the residual stresses, and for the original of the machined residual stress on the surface from the cutting force and the axial force, it can be gained the simply model of tool-workpiece force, using the model it can be deduced the residual stress model, which is feasible to calculate the size of residual stress. And for almost all the measured residual stresses are compressed stress, the compressed stress size and the direction could be confirmed by the input data for the H13 on HSM. As the result, the residual stress model is the key for optimization of rake angle (β) and side rake angle (θ) in theory, using the theory the more cutting mechanism can be expressed.
Astronaut Harrison Schmitt collects lunar rake samples during EVA

NASA Image and Video Library

1972-12-11

AS17-134-20425 (11 Dec. 1972) --- Scientist-astronaut Harrison H. Schmitt, lunar module pilot, collects lunar rake samples at Station 1 during the first Apollo 17 extravehicular activity (EVA) at the Taurus-Littrow landing site. This picture was taken by astronaut Eugene Cernan, commander. The lunar rake, an Apollo lunar geology hand tool, is used to collect discrete samples of rocks and rock chips ranging in size from one-half inch (1.3 centimeter) to one inch (2.5 centimeter).
Constraints on the exploitation of the functional properties of objects in expert tool-using chimpanzees (Pan troglodytes).

PubMed

Povinelli, Daniel J; Frey, Scott H

2016-09-01

Many species exploit immediately apparent dimensions of objects during tool use and manufacture and operate over internal perceptual representations of objects (they move and reorient objects in space, have rules of operation to deform or modify objects, etc). Humans, however, actively test for functionally relevant object properties before such operations begin, even when no previous percepts of a particular object's qualities in the domain have been established. We hypothesize that such prospective diagnostic interventions are a human specialization of cognitive function that has been entirely overlooked in the neuropsychological literature. We presented chimpanzees with visually identical rakes: one was functional for retrieving a food reward; the other was non-functional (its base was spring-loaded). Initially, they learned that only the functional tool could retrieve a distant reward. In test 1, we explored if they would manually test for the rakes' rigidity during tool selection, but before using it. We found no evidence of such behavior. In test 2, we obliged the apes to deform the non-functional tool's base before using it, in order to evaluate whether this would cause them to switch rakes. It did not. Tests 3-6 attempted to focus the apes' attention on the functionally relevant property (rigidity). Although one ape eventually learned to abandon the non-functional rake before using it, she still did not attempt to test the rakes for rigidity prior to use. While these results underscore the ability of chimpanzees to use novel tools, at the same time they point toward a fundamental (and heretofore unexplored) difference in causal reasoning between humans and apes. We propose that this behavioral difference reflects a human specialization in how object properties are represented, which could have contributed significantly to the evolution of our technological culture. We discuss developing a new line of evolutionarily motivated neuropsychological research on action disorders. Copyright © 2016 Elsevier Ltd. All rights reserved.
Research Results Of Stress-Strain State Of Cutting Tool When Aviation Materials Turning

NASA Astrophysics Data System (ADS)

Serebrennikova, A. G.; Nikolaeva, E. P.; Savilov, A. V.; Timofeev, S. A.; Pyatykh, A. S.

2018-01-01

Titanium alloys and stainless steels are hard-to-machine of all the machining types. Cutting edge state of turning tool after machining titanium and high-strength aluminium alloys and corrosion-resistant high-alloy steel has been studied. Cutting forces and chip contact arears with the rake surface of cutter has been measured. The relationship of cutting forces and residual stresses are shown. Cutting forces and residual stresses vs value of cutting tool rake angle relation were obtained. Measurements of residual stresses were performed by x-ray diffraction.
Astronaut Harrison Schmitt collects lunar rake samples during EVA

NASA Image and Video Library

1972-12-11

AS17-134-20426 (11 Dec. 1972) --- Scientist-astronaut Harrison H. Schmitt collects lunar rake samples at Station 1 during the first Apollo 17 extravehicular activity (EVA) at the Taurus-Littrow landing site. This picture was taken by astronaut Eugene A. Cernan, Apollo 17 commander. Schmitt is the lunar module pilot. The Lunar Rake, an Apollo Lunar Geology Hand Tool, is used to collect discrete samples of rocks and rock chips ranging in size from one-half inch (1.3 cm) to one inch (2.5 cm).
Human See, Human Do.

ERIC Educational Resources Information Center

Tomasello, Michael

1997-01-01

A human demonstrator showed human children and captive chimpanzees how to drag food or toys closer using a rakelike tool. One side of the rake was less efficient than the other for dragging. Chimps tried to reproduce results rather than methods while children imitated and used the more efficient rake side. Concludes that imitation leads to…
An application of wake survey rakes to the experimental determination of thrust for a propeller driven aircraft

NASA Technical Reports Server (NTRS)

Hall, K. R.; Miley, S. J.; Tsai, H. J.

1981-01-01

The lack of slipstream static pressure distribution seriously affected the results but recommendations for removing the deficiency are discussed. The wake survey rake is shown to be a valuable tool in aircraft flight testing. Flow characteristics in the wake of the propeller were examined.
Investigation of the Effect of Tool Edge Geometry upon Cutting Variables, Tool Wear and Burr Formation Using Finite Element Simulation — A Progress Report

NASA Astrophysics Data System (ADS)

Sartkulvanich, Partchapol; Al-Zkeri, Ibrahim; Yen, Yung-Chang; Altan, Taylan

2004-06-01

This paper summarizes some of the progress made on FEM simulations of metal cutting processes conducted at the Engineering Research Center (ERC/NSM). Presented research focuses on the performance of various cutting edge geometries (hone and chamfer edges) for different tool materials and specifically on: 1) the effect of round and chamfer edge geometries on the cutting variables in machining carbon steels and 2) the effect of the edge hone size upon the flank wear and burr formation behavior in face milling of A356-T6 aluminum alloy. In the second task, an innovative design of edge preparation with varying hone size around the tool nose is also explored using FEM. In order to model three-dimensional conventional turning and face milling with two-dimensional orthogonal cutting simulations, 2D simulation cross-sections consisting of the cutting speed direction and chip flow direction are selected at different locations along the tool nose radius. Then the geometries of the hone and chamfer edges and their associated tool angles as well as uncut chip thickness are determined on these planes and employed in cutting simulations. The chip flow direction on the tool rake face are obtained by examining the wear grooves on the experimental inserts or estimated by using Oxley's approximation theory of oblique cutting. Simulation results are compared with the available experimental results (e.g. cutting forces) both qualitatively and quantitatively.

The effects of raking on sugar pine mortality following prescribed fire in Sequoia and Kings Canyon National Parks, California, USA

USGS Publications Warehouse

Nesmith, Jonathan C. B.; O'Hara, Kevin L.; van Mantgem, Phillip J.; de Valpine, Perry

2010-01-01

Prescribed fire is an important tool for fuel reduction, the control of competing vegetation, and forest restoration. The accumulated fuels associated with historical fire exclusion can cause undesirably high tree mortality rates following prescribed fires and wildfires. This is especially true for sugar pine (Pinus lambertiana Douglas), which is already negatively affected by the introduced pathogen white pine blister rust (Cronartium ribicola J.C. Fisch. ex Rabenh). We tested the efficacy of raking away fuels around the base of sugar pine to reduce mortality following prescribed fire in Sequoia and Kings Canyon national parks, California, USA. This study was conducted in three prescribed fires and included 457 trees, half of which had the fuels around their bases raked away to mineral soil to 0.5 m away from the stem. Fire effects were assessed and tree mortality was recorded for three years after prescribed fires. Overall, raking had no detectable effect on mortality: raked trees averaged 30% mortality compared to 36% for unraked trees. There was a significant effect, however, between the interaction of raking and average pre-treatment forest floor fuel depth: the predicted probability of survival of a 50 cm dbh tree was 0.94 vs. 0.96 when average pre-treatment fuel depth was 0 cm for a raked and unraked tree, respectively. When average pre-treatment forest floor fuel depth was 30 cm, the predicted probability of survival for a raked 50 cm dbh tree was 0.60 compared to only 0.07 for an unraked tree. Raking did not affect mortality when fire intensity, measured as percent crown volume scorched, was very low (0% scorch) or very high (>80% scorch), but the raking treatment significantly increased the proportion of trees that survived by 9.6% for trees that burned under moderate fire intensity (1% to 80% scorch). Raking significantly reduced the likelihood of bole charring and bark beetle activity three years post fire. Fuel depth and anticipated fire intensity need to be accounted for to maximize the effectiveness of the treatments. Raking is an important management option to reduce tree mortality from prescribed fire, but is most effective under specific fuel and burning conditions.
Dust Emission Induced By Friction Modifications At Tool Chip Interface In Dry Machining In MMCp

NASA Astrophysics Data System (ADS)

Kremer, Arnaud; El Mansori, Mohamed

2011-01-01

This paper investigates the relationship between dust emission and tribological conditions at the tool-chip interface when machining Metal Matrix composite reinforced with particles (MMCp) in dry mode. Machining generates aerosols that can easily be inhaled by workers. Aerosols may be composed of oil mist, tool material or alloying elements of workpiece material. Bar turning tests were conducted on a 2009 aluminum alloy reinforced with different level of Silicon Carbide particles (15, 25 and 35% of SiCp). Variety of PCD tools and nanostructured diamond coatings were used to analyze their performances on air pollution. A spectrometer was used to detect airborne aerosol particles in the size range between 0.3μm to 20 μm and to sort them in 15 size channels in real time. It was used to compare the effects of test parameters on dust emission. Observations of tool face and chip morphology reveal the importance of friction phenomena. It was demonstrated that level of friction modifies chip curvature and dust emission. The increase of level of reinforcement increase the chip segmentation and decrease the contact length and friction area. A "running in" phenomenon with important dust emission appeared with PCD tool due to the tool rake face flatness. In addition dust generation is more sensitive to edge integrity than power consumption.
Strength of inserts in titanium alloy machining

NASA Astrophysics Data System (ADS)

Kozlov, V.; Huang, Z.; Zhang, J.

2016-04-01

In this paper, a stressed state of a non-worn cutting wedge in a machined titanium alloy (Ti6Al2Mo2Cr) is analyzed. The distribution of contact loads on the face of a cutting tool was obtained experimentally with the use of a ‘split cutting tool’. Calculation of internal stresses in the indexable insert made from cemented carbide (WC8Co) was carried out with the help of ANSYS 14.0 software. Investigations showed that a small thickness of the cutting insert leads to extremely high compressive stresses near the cutting edge, stresses that exceed the ultimate compressive strength of cemented carbide. The face and the base of the insert experience high tensile stresses, which approach the ultimate tensile strength of cemented carbide and increase a probability of cutting insert destruction. If the thickness of the cutting insert is bigger than 5 mm, compressive stresses near the cutting edge decrease, and tensile stresses on the face and base decrease to zero. The dependences of the greatest normal and tangential stresses on thickness of the cutting insert were found. Abbreviation and symbols: m/s - meter per second (cutting speed v); mm/r - millimeter per revolution (feed rate f); MPa - mega Pascal (dimension of specific contact loads and stresses); γ - rake angle of the cutting tool [°] α - clearance angle of the sharp cutting tool [°].
Experimental Parametric Model for Indirect Adhesion Wear Measurement in the Dry Turning of UNS A97075 (Al-Zn) Alloy

PubMed Central

Trujillo, Francisco Javier; Sevilla, Lorenzo; Marcos, Mariano

2017-01-01

In this work, the study of the influence of cutting parameters (cutting speed, feed, and depth of cut) on the tool wear used in in the dry turning of cylindrical bars of the UNS A97075 (Al-Zn) alloy, has been analyzed. In addition, a study of the physicochemical mechanisms of the secondary adhesion wear has been carried out. The behavior of this alloy, from the point of view of tool wear, has been compared to similar aeronautical aluminum alloys, such as the UNS A92024 (Al-Cu) alloy and UNS A97050 (Al-Zn) alloy. Furthermore, a first approach to the measurement of the 2D surface of the adhered material on the rake face of the tool has been conducted. Finally, a parametric model has been developed from the experimental results. This model allows predicting the intensity of the secondary adhesion wear as a function of the cutting parameters applied. PMID:28772510
Green Turning of FCD 700 Ductile Cast Iron Using Coated Carbide Tool

NASA Astrophysics Data System (ADS)

Rodzi, Mohd Nor Azmi Mohd; Ghani, Jaharah A.; Eghawail, A. M.; Othman, Kamal; Rahman, Mohd. Nizam Ab.; Haron, Che Hassan Che

2010-10-01

This paper presents the performance of carbide coated cutting insert in turning FCD700 ductile cast iron in various dry machining conditions (without air, using air and chilled air). The turning parameters studied were, cutting speed of 120 m/min., feed rate of 0.15 mm/rev-0.4 mm/rev, and depth of cut of 0.6 mm-1.0 mm. The results show that the tool life was significantly controlled by the type of air coolant used, whereas the cutting force and surface roughness were not influenced by these coolants. Chilled air was found to be significantly improved the tool life by about 30% and 40% respectively when compared with normal air and without air conditions. The wear mechanism was predominantly controlled by the flank and crater wears on the flank and rake faces respectively. Due to the low cutting speed used in the experiment, both flank and crater wears were uniformly formed along the cutting edge and no catastrophic failure was observed under the scanning electron microscope (SEM).
Effect of magneto rheological damper on tool vibration during hard turning

NASA Astrophysics Data System (ADS)

Paul, P. Sam; Varadarajan, A. S.

2012-12-01

Recently, the concept of hard turning has gained considerable attention in metal cutting as it can apparently replace the traditional process cycle of turning, heat treating, and finish grinding for assembly of hard wear resistant steel parts. The present investigation aims at developing a magneto rheological (MR) fluid damper for suppressing tool vibration and promoting better cutting performance during hard turning. The magneto rheological Fluid acts as a viscoelastic spring with non-linear vibration characteristics that are controlled by the composition of the magneto rheological fluid, the shape of the plunger and the electric parameters of the magnetizing field. Cutting experiments were conducted to arrive at a set of electrical, compositional and shape parameters that can suppress tool vibration and promote better cutting performance during turning of AISI 4340 steel of 46 HRC with minimal fluid application using hard metal insert with sculptured rake face. It was observed that the use of MR fluid damper reduces tool vibration and improves the cutting performance effectively. Also commercialization of this idea holds promise to the metal cutting industry.
Study on stability of rake teeth inserting soil of chain rake type mulching film recovery machine based on Adams

NASA Astrophysics Data System (ADS)

Guo, Wensong; Jian, Jianming; San, Yunlong; Lui, Rui; Li, Gang; Hou, Shulin

2017-08-01

Traditional rake type mulching film recycling machine has the problem of difficulty in unloading and packing film, poor continuity of the work. In order to solve such problems, this paper designs a kind of chain rake type mulching film recycling machine which can realize continuous raking film, collecting film, transporting film, shaking off soil, unloading film. Rake teeth is the basic part of chain rake mulching recycling machine. The stability of rake teeth's inserting soil is an important factor to ensure recovery efficiency of the plastic film recovery. By virtual prototype simulation, this paper study the influence of different factors on the stability of rake teeth inserting soil. The results are as follows: The speed of chain rake has no significant effect on the stability of rake teeth inserting soil; Reducing resistance of rake teeth in the process of working, is conducive to improve the stability of rake teeth inserting soil; Appropriate increasing elastic modulus of chain rake, is helpful to enhance the stability of rake teeth inserting soil.
Analyzing the effect of tool edge radius on cutting temperature in micro-milling process

NASA Astrophysics Data System (ADS)

Liang, Y. C.; Yang, K.; Zheng, K. N.; Bai, Q. S.; Chen, W. Q.; Sun, G. Y.

2010-10-01

Cutting heat is one of the important physical subjects in the cutting process. Cutting heat together with cutting temperature produced by the cutting process will directly have effects on the tool wear and the life as well as on the workpiece processing precision and surface quality. The feature size of the workpiece is usually several microns. Thus, the tiny changes of cutting temperature will affect the workpiece on the surface quality and accuracy. Therefore, cutting heat and temperature generated in micro-milling will have significantly different effect than the one in the traditional tools cutting. In this paper, a two-dimensional coupled thermal-mechanical finite element model is adopted to determine thermal fields and cutting temperature during the Micro-milling process, by using software Deform-2D. The effect of tool edge radius on effective stress, effective strain, velocity field and cutting temperature distribution in micro-milling of aluminum alloy Al2024-T6 were investigated and analyzed. Also, the transient cutting temperature distribution was simulated dynamically. The simulation results show that the cutting temperature in Micro-milling is lower than those occurring in conventional milling processes due to the small loads and low cutting velocity. With increase of tool edge radius, the maximum temperature region gradually occurs on the contact region between finished surfaced and flank face of micro-cutter, instead of the rake face or the corner of micro-cutter. And this phenomenon shows an obvious size effect.
Analysis about diamond tool wear in nano-metric cutting of single crystal silicon using molecular dynamics method

NASA Astrophysics Data System (ADS)

Wang, Zhiguo; Liang, Yingchun; Chen, Mingjun; Tong, Zhen; Chen, Jiaxuan

2010-10-01

Tool wear not only changes its geometry accuracy and integrity, but also decrease machining precision and surface integrity of workpiece that affect using performance and service life of workpiece in ultra-precision machining. Scholars made a lot of experimental researches and stimulant analyses, but there is a great difference on the wear mechanism, especially on the nano-scale wear mechanism. In this paper, the three-dimensional simulation model is built to simulate nano-metric cutting of a single crystal silicon with a non-rigid right-angle diamond tool with 0 rake angle and 0 clearance angle by the molecular dynamics (MD) simulation approach, which is used to investigate the diamond tool wear during the nano-metric cutting process. A Tersoff potential is employed for the interaction between carbon-carbon atoms, silicon-silicon atoms and carbon-silicon atoms. The tool gets the high alternating shear stress, the tool wear firstly presents at the cutting edge where intension is low. At the corner the tool is splitted along the {1 1 1} crystal plane, which forms the tipping. The wear at the flank face is the structure transformation of diamond that the diamond structure transforms into the sheet graphite structure. Owing to the tool wear the cutting force increases.
A sex difference in effect of prior experience on object-mediated problem-solving in gibbons.

PubMed

Cunningham, Clare; Anderson, James; Mootnick, Alan

2011-07-01

Understanding the functionally relevant properties of objects is likely facilitated by learning with a critical role for past experience. However, current evidence is conflicting regarding the effect of prior object exposure on acquisition of object manipulation skills. This may be due to the influence of life history variables on the capacity to benefit from such experience. This study assessed effect of task-relevant object exposure on object-mediated problem-solving in 22 gibbons using a raking-in task. Despite not using tools habitually, 14 gibbons spontaneously used a rake to obtain a reward. Having prior experience with the rake in an unrewarded context did not improve learning efficiency in males. However, females benefitted significantly from the opportunity to interact with the rake before testing, with reduced latencies to solution compared to those with no previous exposure. These results reflect potential sex differences in approach to novelty that moderate the possible benefits of prior experience. Due to their relatively high energetic requirements, reproductively active females may be highly motivated to explore potential resources; however, increased investment in developing offspring could make them more guarded in their investigations. Previous exposure that allows females to learn of an object's neutrality can offset this cautious exploration.
Evaluation of the Performance and Flow in an Axial Compressor.

DTIC Science & Technology

1982-10-01

A Exit Rake P 11.00-P tP noz P2noz -PA SP-1 PHub - PA Exit Rake Pt11.50-Pt p - PA SP-1 PTip - PA Exit Rake Pt2.00-PPtpipe ATp Att Pspipe - PA SP-2...PTip - PA Exit Rake Pt6.50-Pt Inlet Rake Pt14.40-PA SP-8 PTip - PA Exit Rake Pt 17.00-Pt Inlet Rake Pt 1.30-PA SP-8 PHub - PA Exit Rake Pt17.50-Pt...Determination from Probe Pressures Pt (1) =((Pt=(1) + Phub ) + (Pt(1) + Pt(2)))/3 P t(2) P t(2) Pt (3) = t(3) P t(4) = (P t(3) + P t(4))/2 P t(5) =P t(4) Pt
Design and Evaluation of a New Boundary-Layer Rake for Flight Testing

NASA Technical Reports Server (NTRS)

Bui, Trong T.; Oates, David L.; Gonsalez, Jose C.

2000-01-01

A new boundary-layer rake has been designed and built for flight testing on the NASA Dryden Flight Research Center F-15B/Flight Test Fixture. A feature unique to this rake is its curved body, which allows pitot tubes to be more densely clustered in the near-wall region than conventional rakes allow. This curved rake design has a complex three-dimensional shape that requires innovative solid-modeling and machining techniques. Finite-element stress analysis of the new design shows high factors of safety. The rake has passed a ground test in which random vibration measuring 12 g rms was applied for 20 min in each of the three normal directions. Aerodynamic evaluation of the rake has been conducted in the NASA Glenn Research Center 8 x 6 Supersonic Wind Tunnel at Mach 0-2. The pitot pressures from the new rake agree with conventional rake data over the range of Mach numbers tested. The boundary-layer profiles computed from the rake data have been shown to have the standard logarithmic-law profile. Skin friction values computed from the rake data using the Clauser plot method agree with the Preston tube results and the van Driest II compressible skin friction correlation to approximately +/-5 percent.
Cutting Zone Temperature Identification During Machining of Nickel Alloy Inconel 718

NASA Astrophysics Data System (ADS)

Czán, Andrej; Daniš, Igor; Holubják, Jozef; Zaušková, Lucia; Czánová, Tatiana; Mikloš, Matej; Martikáň, Pavol

2017-12-01

Quality of machined surface is affected by quality of cutting process. There are many parameters, which influence on the quality of the cutting process. The cutting temperature is one of most important parameters that influence the tool life and the quality of machined surfaces. Its identification and determination is key objective in specialized machining processes such as dry machining of hard-to-machine materials. It is well known that maximum temperature is obtained in the tool rake face at the vicinity of the cutting edge. A moderate level of cutting edge temperature and a low thermal shock reduce the tool wear phenomena, and a low temperature gradient in the machined sublayer reduces the risk of high tensile residual stresses. The thermocouple method was used to measure the temperature directly in the cutting zone. An original thermocouple was specially developed for measuring of temperature in the cutting zone, surface and subsurface layers of machined surface. This paper deals with identification of temperature and temperature gradient during dry peripheral milling of Inconel 718. The measurements were used to identification the temperature gradients and to reconstruct the thermal distribution in cutting zone with various cutting conditions.
New tool holder design for cryogenic machining of Ti6Al4V

NASA Astrophysics Data System (ADS)

Bellin, Marco; Sartori, Stefano; Ghiotti, Andrea; Bruschi, Stefania

2017-10-01

The renewed demand of increasing the machinability of the Ti6Al4V titanium alloy to produce biomedical and aerospace parts working at high temperature has recently led to the application of low-temperature coolants instead of conventional cutting fluids to increase both the tool life and the machined surface integrity. In particular, the liquid nitrogen directed to the tool rake face has shown a great capability of reducing the temperature at the chip-tool interface, as well as the chemical interaction between the tool coating and the titanium to be machined, therefore limiting the tool crater wear, and improving, at the same time, the chip breakability. Furthermore, the nitrogen is a safe, non-harmful, non-corrosive, odorless, recyclable, non-polluting and abundant gas, characteristics that further qualify it as an environmental friendly coolant to be applied to machining processes. However, the behavior of the system composed by the tool and the tool holder, exposed to the cryogenics temperatures may represent a critical issue in order to obtain components within the required geometrical tolerances. On this basis, the paper aims at presenting the design of an innovative tool holder installed on a CNC lathe, which includes the cryogenic coolant provision system, and which is able to hinder the part possible distortions due to the liquid nitrogen adduction by stabilizing its dimensions through the use of heating cartridges and appropriate sensors to monitor the temperature evolution of the tool holder.
9. VIEW OF THE TRASH RAKES, TRASH RAKE GATELIFTING MECHANISM, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. VIEW OF THE TRASH RAKES, TRASH RAKE GATE-LIFTING MECHANISM, AND SHED ROOF (REMOVED AUTUMN OF 1996), WITH TRASH LOG LIFTING MECHANISM IN FOREGROUND, LOOKING WEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID
The evaluation of a rake method to quantify submersed vegetation in the Upper Mississippi River

USGS Publications Warehouse

Yin, Yao; Kreiling, Rebecca M.

2011-01-01

A long-handled, double-headed garden rake was used to collect submersed aquatic vegetation (SAV) and compared to in-boat visual inspection to record species presence at 67 individual sites. Six rake subsamples were taken at each site and a rake density rating was given to each species collected in the subsamples. Presence at the site, frequency of occurrence in the six rake samples, and additive density rating (the sum of the six rake density ratings) were quantified for each species at each site. The validity of the indices was tested against biomass data collected by clipping all remaining vegetation from the 67 sites. In the turbid water of the Mississippi River, visual inspection of SAV from boats was ineffective with only 27% of the species detected, while raking retrieved on average 70% of the total number of submersed species in the 67 sites. Presence of species at individual sites was correlated with biomass from Stuckenia pectinata, while frequency of occurrence and additive density rating were correlated with biomass for species with greater than 21 g of total biomass from all sites. The efficiency of the rake to collect biomass varied among species; only 18% of total biomass was captured via raking the site six times. Additive density rating as an index of abundance can be used to detect temporal changes in the same water body; however, cross-species comparison is not encouraged unless the efficiency of the rake has been determined for each species being compared.
Side Flow Effect on Surface Generation in Nano Cutting

NASA Astrophysics Data System (ADS)

Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

2017-05-01

The side flow of material in nano cutting is one of the most important factors that deteriorate the machined surface quality. The effects of the crystallographic orientation, feed, and the cutting tool geometry, including tool edge radius, rake angle and inclination angle, on the side flow are investigated employing molecular dynamics simulation. The results show that the stagnation region is formed in front of tool edge and it is characterized by the stagnation radius R s and stagnation height h s . The side flow is formed because the material at or under the stagnation region is extruded by the tool edge to flow to the side of the tool edge. Higher stagnation height would increase the size of the side flow. The anisotropic nature of the material which partly determines the stagnation region also influences the side flow due to the different deformation mechanism under the action of the tool edge. At different cutting directions, the size of the side flow has a great difference which would finally affect the machined surface quality. The cutting directions of {100} < 011>, {110} < 001>, and {110} < 1-10 > are beneficial to obtain a better surface quality with small side flow. Besides that, the side flow could be suppressed by reducing the feed and optimizing the cutting tool geometry. Cutting tool with small edge radius, large positive rake angle, and inclination angle would decrease the side flow and consequently improve the machined surface quality.
Side Flow Effect on Surface Generation in Nano Cutting.

PubMed

Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

2017-12-01

The side flow of material in nano cutting is one of the most important factors that deteriorate the machined surface quality. The effects of the crystallographic orientation, feed, and the cutting tool geometry, including tool edge radius, rake angle and inclination angle, on the side flow are investigated employing molecular dynamics simulation. The results show that the stagnation region is formed in front of tool edge and it is characterized by the stagnation radius R s and stagnation height h s . The side flow is formed because the material at or under the stagnation region is extruded by the tool edge to flow to the side of the tool edge. Higher stagnation height would increase the size of the side flow. The anisotropic nature of the material which partly determines the stagnation region also influences the side flow due to the different deformation mechanism under the action of the tool edge. At different cutting directions, the size of the side flow has a great difference which would finally affect the machined surface quality. The cutting directions of {100} < 011>, {110} < 001>, and {110} < 1-10 > are beneficial to obtain a better surface quality with small side flow. Besides that, the side flow could be suppressed by reducing the feed and optimizing the cutting tool geometry. Cutting tool with small edge radius, large positive rake angle, and inclination angle would decrease the side flow and consequently improve the machined surface quality.
Does raking basal duff affect tree growth rates or mortality?

Treesearch

Erin Noonan-Wright; Sharon M. Hood; Danny R. Cluck

2010-01-01

Mortality and reduced growth rates due to raking accumulated basal duff were evaluated for old, large-diameter ponderosa and Jeffrey pine trees on the Lassen National Forest, California. No fire treatments were included to isolate the effect of raking from fire. Trees were monitored annually for 5 years after the raking treatment for mortality and then cored to measure...
Semiempirical method of determining flow coefficients for pitot rake mass flow rate measurements

NASA Technical Reports Server (NTRS)

Trefny, C. J.

1985-01-01

Flow coefficients applicable to area-weighted pitot rake mass flow rate measurements are presented for fully developed, turbulent flow in an annulus. A turbulent velocity profile is generated semiempirically for a given annulus hub-to-tip radius ratio and integrated numerically to determine the ideal mass flow rate. The calculated velocities at each probe location are then summed, and the flow rate as indicated by the rake is obtained. The flow coefficient to be used with the particular rake geometry is subsequently obtained by dividing the ideal flow rate by the rake-indicated flow rate. Flow coefficients ranged from 0.903 for one probe placed at a radius dividing two equal areas to 0.984 for a 10-probe area-weighted rake. Flow coefficients were not a strong function of annulus hub-to-tip radius ratio for rakes with three or more probes. The semiempirical method used to generate the turbulent velocity profiles is described in detail.

Characterization of N-doped polycrystalline diamond films deposited on microgrinding tools

NASA Astrophysics Data System (ADS)

Jackson, M. J.; Ahmed, W.

2005-10-01

Chemical vapor deposited diamond films have many industrial applications but are assuming increasing importance in the area of microengineering, most notably in the development of diamond coated microgrinding tools. For these applications the control of structure and morphology is of critical importance. The crystallite size, orientation, surface roughness, and the degree of sp 3 character have a profound effect on the tribological properties of the films deposited. In this article, we present experimental results on the effects of nitrogen doping on the surface morphology, crystallite size, and wear of microgrinding tools. The sp 3 character optimizes at 200 ppm nitrogen, and above this value the surface becomes much smoother and crystal sizes decrease considerably. Fracture-induced wear of the diamond grain is the most important mechanism of material removal from a microgrinding tool during the grinding process. Fracture occurs as a consequence of tensile stresses induced into diamond grains by grinding forces to which they are subjected. The relationship between the wear of diamond coated grinding tools, component grinding forces, and induced stresses in the model diamond grains is described in detail. A significant correlation was found between the maximum value of tensile stress induced in the diamond grain and the appropriate wheel-wear parameter (grinding ratio). It was concluded that the magnitude of tensile stresses induced in the diamond grain by grinding forces at the rake face is the best indicator of tool wear during the grinding process.
Analyzing the effect of cutting parameters on surface roughness and tool wear when machining nickel based hastelloy - 276

NASA Astrophysics Data System (ADS)

Khidhir, Basim A.; Mohamed, Bashir

2011-02-01

Machining parameters has an important factor on tool wear and surface finish, for that the manufacturers need to obtain optimal operating parameters with a minimum set of experiments as well as minimizing the simulations in order to reduce machining set up costs. The cutting speed is one of the most important cutting parameter to evaluate, it clearly most influences on one hand, tool life, tool stability, and cutting process quality, and on the other hand controls production flow. Due to more demanding manufacturing systems, the requirements for reliable technological information have increased. For a reliable analysis in cutting, the cutting zone (tip insert-workpiece-chip system) as the mechanics of cutting in this area are very complicated, the chip is formed in the shear plane (entrance the shear zone) and is shape in the sliding plane. The temperature contributed in the primary shear, chamfer and sticking, sliding zones are expressed as a function of unknown shear angle on the rake face and temperature modified flow stress in each zone. The experiments were carried out on a CNC lathe and surface finish and tool tip wear are measured in process. Machining experiments are conducted. Reasonable agreement is observed under turning with high depth of cut. Results of this research help to guide the design of new cutting tool materials and the studies on evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy - 276 machining.
Impact of raking and bioturbation-mediated ecological manipulation on sediment-water phosphorus diagenesis: a mesocosm study supported with radioactive signature.

PubMed

Biswas, Jayanta K; Hazra, Saumen; Majumdar, Jayjit; Mandal, Sushil K; Shaheen, Sabry M; Sarkar, Santosh K; Meissner, Ralph; Meers, Erik; Rinklebe, Jörg

2017-12-01

The study examined the impact of raking and fish bioturbation on modulating phosphorus (P) concentrations in the water and sediment under different trophic conditions. An outdoor experiment was set to monitor physicochemical and microbiological parameters of water and sediment influencing P diagenesis. A pilot study with radioactive 32 P was also performed under the agency of raking and bacteria (Bacillus sp.). Raking was more effective in release of P under unfertilized conditions by significantly enhancing orthophosphate (35%) and soluble reactive phosphate (31.8%) over respective controls. Bioturbation increased total and available P in sediments significantly as compared to control. The rates of increase were higher in the unfertilized conditions (17.6-28.4% for total P and 12.2 to 23.2% for available P) than the fertilized ones (6.5-12.4% for total P and 9.1 to 15% for available P). The combined effects of raking and bioturbation on orthophosphate and soluble reactive phosphate were also stronger under unfertilized state (54.5 and 81.8%) than fertilized ones (50 and 70%). The tracer signature showed that coupled action of introduced bacteria and repeated raking resulted in 59.2, 23 and 16% higher counts of radioactive P than the treatments receiving raking once, repeated raking and bacteria inoculation, respectively. Raking alone or in sync with bioturbation exerted pronounced impact on P diagenesis through induction of coupled mineralization and nutrient release. It has significant implication for performing regular raking of fish-farm sediments and manipulation of bottom-grazing fish to regulate mineralization of organic matter and release of obnoxious gases from the system. Further, they synergistically can enhance the buffering capacity against organic overload and help to maintain aquatic ecosystem health.
Pinestraw raking, fertilization and poultry litter amendment effects on soil physical properties for a mid-rotation loblolly pine plantation

Treesearch

William B. Patterson; Michael A. Blazier; Steven L. Holtard

2010-01-01

Frequent pinestraw raking and removal in pine plantations has led to concerns about nutrient removal from the stand. While soil chemistry of raked stands has been studied, little attention has been placed on potential compaction from raking operations. Four treatments were applied to a 16-year-old loblolly pine plantation at the Louisiana State University AgCenter...
Dual Rotating Rake Measurements of Higher-Order Duct Modes: Validation Using Experimental and Numerical Data

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Hixon, Duane R.; Sutliff, Daniel L.

2018-01-01

A rotating rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode coefficient amplitudes and phases were quantified. Early studies using this system found that mode power levels computed from rotating rake measured data would agree with the far-field power levels. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection and previous studies suggested conditions could exist where significant reflections could occur. This paper shows that mounting a second rake to the rotating system, with an offset in both the axial and the azimuthal directions, measures the data necessary to determine the modes propagating in both directions within a duct. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode coefficients at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode coefficients for the modes propagating in both directions within the duct while accounting for the presence of evanescent modes. The validation of the dual-rotating-rake measurements was conducted using data from a combination of experiments and numerical calculations to compute reflection coefficients and other mode coefficient ratios. Compared to results from analytical and numerical computations, the results from dual-rotating-rake measured data followed the expected trends when frequency, mode number, and duct termination geometry were changed.
Flow Visualization on a Small Scale.

DTIC Science & Technology

1988-03-01

1150 22.43 26 A good tunnel must have very uniform flow across the test section. The uniformity was checked using a seven tube pitot static rake ...calibration. il Figure 7. The Pitot Static Rake 27 To map the entire 15 x 24 inch cross section 84 individual readings and 12 rake locations were required... rake readings was taken, the micromanometer was reattached to the permanent pitot static probe to ensure calibration of the tunnel to .02 inches of
Further Development of Rotating Rake Mode Measurement Data Analysis

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Hixon, Ray; Sutliff, Daniel L.

2013-01-01

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode amplitudes and phases were quantified. For low-speed fans within axisymmetric ducts, mode power levels computed from rotating rake measured data would agree with the far-field power levels on a tone by tone basis. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection at the exit and previous studies suggested conditions could exist where significant reflections could occur. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. The fit equations were also modified to allow evanescent mode amplitudes to be computed. This extension of the rotating rake data analysis technique was tested using simulated data, numerical code produced data, and preliminary in-duct measured data.
Tool wear mechanisms in turning titanium-aluminum-vanadium using tungsten carbide and polycrystalline diamond inserts

NASA Astrophysics Data System (ADS)

Schrock, David James

The objective of this work is to identify some of the tool wear mechanisms at the material level for the machining of titanium and to provide some understanding of these mechanisms for use in physics based tool wear models. Turning experiments were conducted at cutting speeds of 61m/min, 91m/min, and 122m/min on Ti-6Al-4V, an alloy of titanium, using two different grades of tungsten carbide cutting inserts and one grade of polycrystalline diamond inserts. Three-dimensional wear data and two-dimensional wear profiles of the rake face were generated using Confocal Laser Scanning Microscopy to quantify the tool wear mechanisms. Additionally, the microstructure of the deformed work material (chip) and un-deformed parent material (work piece) were studied using Orientation Imaging Microscopy (OIM). Observations from tool wear studies on the PCD inserts revealed the presence of two fundamentally different wear mechanisms operating at the different cutting speeds. Microstructural analyses of the chip and the work material showed phase dependent tool wear mechanisms for machining titanium. There is a high likelihood of phase change occurring in the work material during machining, with a transformation from the alpha phase to the beta phase. The observed dramatic increase in wear is attributed to a combination of increased diffusivity in the beta phase of the titanium alloy in conjunction with a higher degree of recrystallization of the prior beta phase upon cooling. Results of other observations such as the influence of carbide grain size on tool wear are also discussed.
Analysis of Dual Rotating Rake Data from the NASA Glenn Advanced Noise Control Fan Duct with Artificial Sources

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Sutliff, Daniel L.

2014-01-01

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. Initially, the mode amplitudes and phases were quantified from a single rake measurement at one axial location. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was then extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. Validation experiments have been conducted using artificial acoustic sources. Results are shown for the measurement of the standing waves in the duct from sound generated by one and two acoustic sources that are separated into the component modes propagating in both directions within the duct. Measured reflection coefficients from the open end of the duct are compared to analytical predictions.
Ground Impingement of a Fan Jet Exhaust Plume

DTIC Science & Technology

1978-05-01

ground plane to avoid a possible interaction between the ground-deflected exhaust and the fan j .t engine inlet. Two pitot pressure rakes , shown on the...Pressure signals from the two rakes (total of 18 pitot tubes) were read sequentially with a Scannivalve system, time-averaged, and displayed on a pen...taken from the inner anid outer rakes with the ground plane normal to the flow at h/d f 2. Pitot pressures from each rake were normalized by the
Multipurpose Rotating Rake Arrays for Integrated Inlet and Fan Stage Performance Measurement

NASA Technical Reports Server (NTRS)

Wolter, John D.

2017-01-01

Low-pressure-ratio fan stage performance measurement requires precise measurement of conditions upstream and downstream of the fan stage. This presentation will discuss the rotating rake arrays used for the recent Boundary Layer Ingesting Inlet-Distortion-Tolerant Fan experiment in the NASA Glenn 8 by 6 foot wind tunnel. To achieve precise measurements, simulations of the rake sampling from pre-test CFD (Computerized Fluid Dynamics) solutions were used to optimize the number and locations of rake instruments.
Rotating Rake Turbofan Duct Mode Measurement System

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2005-01-01

An experimental measurement system was developed and implemented by the NASA Glenn Research Center in the 1990s to measure turbofan duct acoustic modes. The system is a continuously rotating radial microphone rake that is inserted into the duct. This Rotating Rake provides a complete map of the acoustic duct modes present in a ducted fan and has been used on a variety of test articles: from a low-speed, concept test rig, to a full-scale production turbofan engine. The Rotating Rake has been critical in developing and evaluating a number of noise reduction concepts as well as providing experimental databases for verification of several aero-acoustic codes. More detailed derivation of the unique Rotating Rake equations are presented in the appendix.
Design and development of an F/A-18 inlet distortion rake: A cost and time saving solution

NASA Technical Reports Server (NTRS)

Yuhas, Andrew J.; Ray, Ronald J.; Burley, Richard R.; Steenken, William G.; Lechtenberg, Leon; Thornton, Don

1995-01-01

An innovative inlet total pressure distortion measurement rake has been designed and developed for the F/A-18 A/B/C/D aircraft inlet. The design was conceived by NASA and General Electric Aircraft Engines personnel. This rake has been flight qualified and flown in the F/A-18 High Alpha Research Vehicle at NASA Dryden Flight Research Center, Edwards, California. The eight-legged, one-piece, wagon wheel design of the rake was developed at a reduced cost and offered reduced installation time compared to traditional designs. The rake features 40 dual-measurement ports for low- and high-frequency pressure measurements with the high-frequency transducer mounted at the port. This high-frequency transducer offers direct absolute pressure measurements from low to high frequencies of interest, thereby allowing the rake to be used during highly dynamic aircraft maneuvers. Outstanding structural characteristics are inherent to the design through its construction and use of lightweight materials.
Aero-Thermal Calibration of the NASA Glenn Icing Research Tunnel (2012 Test)

NASA Technical Reports Server (NTRS)

Pastor-Barsi, Christine M.; Arrington, E. Allen; VanZante, Judith Foss

2012-01-01

A major modification of the refrigeration plant and heat exchanger at the NASA Glenn Icing Research Tunnel (IRT) occurred in autumn of 2011. It is standard practice at NASA Glenn to perform a full aero-thermal calibration of the test section of a wind tunnel facility upon completion of major modifications. This paper will discuss the tools and techniques used to complete an aero-thermal calibration of the IRT and the results that were acquired. The goal of this test entry was to complete a flow quality survey and aero-thermal calibration measurements in the test section of the IRT. Test hardware that was used includes the 2D Resistive Temperature Detector (RTD) array, 9-ft pressure survey rake, hot wire survey rake, and the quick check survey rake. This test hardware provides a map of the velocity, Mach number, total and static pressure, total temperature, flow angle and turbulence intensity. The data acquired were then reduced to examine pressure, temperature, velocity, flow angle, and turbulence intensity. Reduced data has been evaluated to assess how the facility meets flow quality goals. No icing conditions were tested as part of the aero-thermal calibration. However, the effects of the spray bar air injections on the flow quality and aero-thermal calibration measurements were examined as part of this calibration.
Thrust Vectoring for Advanced Fighter Aircraft - High Angle of Attack Intake Investigations -

DTIC Science & Technology

2001-06-01

these losses. plane) a rake for the measurement of swirl and pressure recovery has been used. The five-hole probes and the pitot Whereas the total...true for the two be recognized in fig. 4,3.1. There exist 8 rake arms with 7 pitot intake parameters mean swirl and dynamic distortion. In order probes...recognized that at the low intake mass this rake is measured with the help of 16 rake arms with 5 pitot flowT the pressure recovery up to an angle of
Distribution of contact loads over the flank-land of the cutter with a rounded cutting edge

NASA Astrophysics Data System (ADS)

Kozlov, V.; Gerasimov, A.; Kim, A.

2016-04-01

In this paper, contact conditions between a tool and a workpiece material for wear-simulating turning by a cutter with a sharp-cornered edge and with a rounded cutting edge are analysed. The results of the experimental study of specific contact load distribution over the artificial flank wear-land of the cutter in free orthogonal turning of the disk from titanium alloy (Ti6Al2Mo2Cr), ductile (63Cu) and brittle (57Cu1Al3Mn) brasses are described. Investigations were carried out by the method of ‘split cutter’ and by the method of the artificial flank-land of variable width. The experiments with a variable feed rate and a cutting speed show that in titanium alloy machining with a sharp-cornered cutting edge the highest normal contact load (σh max = 3400…2200 MPa) is observed immediately at the cutting edge, and the curve has a horizontal region with the length of 0.2… 0.6 mm. At a distance from the cutting edge, the value of specific normal contact load is dramatically reduced to 1100…500 MPa. The character of normal contact load for a rounded cutting edge is different -it is uniform, and its value is approximately 2 times smaller compared to machining with a sharp-cornered cutting edge. In author’s opinion it is connected with generation of a seizure zone in a chip formation region and explains the capacity of highly worn-out cutting tools for titanium alloys machining. The paper analyses the distribution of tangential contact loads over the flank land, which pattern differs considerably for machining with a sharp-cornered edge and with a rounded cutting edge. Abbreviation and symbols: m/s - meter per second (cutting speed v); mm/r - millimeter per revolution (feed rate f); MPa - mega Pascal (specific contact load as a stress σ or τ) hf - the width of the flank wear land (chamfer) of the cutting tool, flank wear land can be natural or artificial like the one in this paper [mm]; xh - distance from the cutting edge on the surface of the flank-land [mm]; σh - normal specific contact load on the flank land [MPa]; τh - tangential (shear) specific contact load on the flank land [MPa]; HSS - high speed steel (material of cutting tool); Py - radial component of cutting force [N]; Py r - radial component of cutting force on the rake face [N]; Pz - tangential component of cutting force [N]; γ - rake angle of the cutting tool [°] α - clearance angle of the sharp cutting tool [°] αh - clearance angle of the flank wear land [°] ρ - rounding off radius of the cutting edge [mm]; b - width of the machined disk [mm].
Biomechanics of a convergently derived prey-processing mechanism in fishes: evidence from comparative tongue bite apparatus morphology and raking kinematics.

PubMed

Konow, Nicolai; Sanford, Christopher P J

2008-11-01

A tongue-bite apparatus (TBA) governs raking behaviors in two major and unrelated teleost lineages, the osteoglossomorph and salmoniform fishes. We present data on comparative morphology and kinematics from two representative species, the rainbow trout (Oncorhynchus mykiss) and the Australian arowana (Scleropages jardinii), which suggest that both the TBA and raking are convergently derived in these lineages. Similar TBA morphologies were present, except for differences in TBA dentition and shape of the novel cleithrobranchial ligament (CBL), which is arc-shaped in O. mykiss and straight in S. jardinii. Eight kinematic variables were used to quantify motion magnitude and maximum-timing in the kinematic input mechanisms of the TBA. Five variables differed inter-specifically (pectoral girdle retraction magnitude and timing, cranial and hyoid elevation and gape-distance timing), yet an incomplete taxon separation across multivariate kinematic space demonstrated an overall similarity in raking behavior. An outgroup analysis using bowfin (Amia calva) and pickerel (Esox americanus) to compare kinematics of raking with chewing and prey-capture provided robust quantitative evidence of raking being a convergently derived behavior. Support was also found for the notion that raking more likely evolved from the strike, a functionally distinct behavior, than from chewing, an alternative prey-processing behavior. Based on raking kinematic and muscle-activity data, we propose biomechanical models of the three input mechanisms that govern kinematics of the basihyal output mechanism during the raking power stroke: (1) cranial elevation protracts the upper TBA jaw from the lower (basihyal) TBA jaw; (2) basihyal retraction is caused directly by contraction of the sternohyoideus (SH); (3) hypaxial shortening, relayed via the pectoral girdle and SH-CBL complex, is an indirect basihyal retraction mechanism modeled as a four-bar linkage. These models will aid future analyses mapping structural and functional traits to the evolution of behaviors.
Longleaf pine site response to repeated fertilization and forest floor removal by raking and prescribed burning

Treesearch

Kim Ludovici; Robert Eaton; Stanley Zarnoch

2018-01-01

Removal of forest floor litter by pine needle raking and prescribed burning is a common practice in longleaf pine (Pinus palustris Mill.) stands on Coastal Plain sites in the Southeastern United States. Repeated removal of litter by raking and the loss of surface organic matter from controlled burns can affect the...
Skin-Friction Measurements at Subsonic and Transonic Mach Numbers with Embedded-Wire Gages

DTIC Science & Technology

1981-01-01

Model ................................... 17 9. Boundary-Layer Rake Installation on EBOR Model...boundary-layer total pressure rake eliminates this bulky mechanism and the long data acquisition time, but it introduces interferences which affect the...its construction. Further, boundary-layer rakes are restricted to measurements in thick boundary layers. Surface pressure probes such as Stanton tubes
Power optimization of digital baseband WCDMA receiver components on algorithmic and architectural level

NASA Astrophysics Data System (ADS)

Schämann, M.; Bücker, M.; Hessel, S.; Langmann, U.

2008-05-01

High data rates combined with high mobility represent a challenge for the design of cellular devices. Advanced algorithms are required which result in higher complexity, more chip area and increased power consumption. However, this contrasts to the limited power supply of mobile devices. This presentation discusses the application of an HSDPA receiver which has been optimized regarding power consumption with the focus on the algorithmic and architectural level. On algorithmic level the Rake combiner, Prefilter-Rake equalizer and MMSE equalizer are compared regarding their BER performance. Both equalizer approaches provide a significant increase of performance for high data rates compared to the Rake combiner which is commonly used for lower data rates. For both equalizer approaches several adaptive algorithms are available which differ in complexity and convergence properties. To identify the algorithm which achieves the required performance with the lowest power consumption the algorithms have been investigated using SystemC models regarding their performance and arithmetic complexity. Additionally, for the Prefilter Rake equalizer the power estimations of a modified Griffith (LMS) and a Levinson (RLS) algorithm have been compared with the tool ORINOCO supplied by ChipVision. The accuracy of this tool has been verified with a scalable architecture of the UMTS channel estimation described both in SystemC and VHDL targeting a 130 nm CMOS standard cell library. An architecture combining all three approaches combined with an adaptive control unit is presented. The control unit monitors the current condition of the propagation channel and adjusts parameters for the receiver like filter size and oversampling ratio to minimize the power consumption while maintaining the required performance. The optimization strategies result in a reduction of the number of arithmetic operations up to 70% for single components which leads to an estimated power reduction of up to 40% while the BER performance is not affected. This work utilizes SystemC and ORINOCO for the first estimation of power consumption in an early step of the design flow. Thereby algorithms can be compared in different operating modes including the effects of control units. Here an algorithm having higher peak complexity and power consumption but providing more flexibility showed less consumption for normal operating modes compared to the algorithm which is optimized for peak performance.

Calibration of a pitot-static rake

NASA Technical Reports Server (NTRS)

Stump, H. P.

1977-01-01

A five-element pitot-static rake was tested to confirm its accuracy and determine its suitability for use at Langley during low-speed tunnel calibration primarily at full-scale tunnel. The rake was tested at one airspeed of 74 miles per hour (33 meters per second) and at pitch and yaw angles of 0 to + or - 20 degrees in 4 deg increments.
Effect of Geometric Parameters on the Performance of Second Throat Annular Steam Ejectors

DTIC Science & Technology

1991-07-01

Cell Pressure versus Rake Average Exit Pitot Pressure . . . . . . . . . . . 42 15. Baseline Wall Pressure Profiles...diffuser exit plane pitot pressure rake . 2.5.2 Alternate Configurations Six alternate ejector diffuser configurations were tested. A summary of...along the walls of the diffusers to help characterize the flow. The ejector diffuser exit pitot pressure was measured with a 6-probe pitot pressure rake
Finite Element Analysis Of Influence Of Flank Wear Evolution On Forces In Orthogonal Cutting Of 42CrMo4 Steel

NASA Astrophysics Data System (ADS)

Madajewski, Marek; Nowakowski, Zbigniew

2017-01-01

This paper presents analysis of flank wear influence on forces in orthogonal turning of 42CrMo4 steel and evaluates capacity of finite element model to provide such force values. Data about magnitude of feed and cutting force were obtained from measurements with force tensiometer in experimental test as well as from finite element analysis of chip formation process in ABAQUS/Explicit software. For studies an insert with complex rake face was selected and flank wear was simulated by grinding operation on its flank face. The aim of grinding inset surface was to obtain even flat wear along cutting edge, which after the measurement could be modeled with CAD program and applied in FE analysis for selected range of wear width. By comparing both sets of force values as function of flank wear in given cutting conditions FEA model was validated and it was established that it can be applied to analyze other physical aspects of machining. Force analysis found that progression of wear causes increase in cutting force magnitude and steep boost to feed force magnitude. Analysis of Fc/Ff force ratio revealed that flank wear has significant impact on resultant force in orthogonal cutting and magnitude of this force components in cutting and feed direction. Surge in force values can result in transfer of substantial loads to machine-tool interface.
Congruence between muscle activity and kinematics in a convergently derived prey-processing behavior.

PubMed

Konow, Nicolai; Camp, Ariel L; Sanford, Christopher P J

2008-08-01

Quantification of anatomical and physiological characteristics of the function of a musculoskeletal system may yield a detailed understanding of how the organizational levels of morphology, biomechanics, kinematics, and muscle activity patterns (MAPs) influence behavioral diversity. Using separate analyses of these organizational levels in representative study taxa, we sought patterns of congruence in how organizational levels drive behavioral modulation in a novel raking prey-processing behavior found in teleosts belonging to two evolutionarily distinct lineages. Biomechanically divergent prey (elusive, robust goldfish and sedentary, malleable earthworms) were fed to knifefish, Chitala ornata (Osteoglossomorpha) and brook trout, Salvelinus fontinalis (Salmoniformes). Electromyography recorded MAPs from the hyoid protractor, jaw adductor, sternohyoideus, epaxialis, and hypaxialis musculature, while sonomicrometry sampled deep basihyal kinesis and contractile length dynamics in the basihyal protractor and retractor muscles. Syntheses of our results with recent analyses of cranial morphology and raking kinematics showed that raking in Salvelinus relies on an elongated cranial out lever, extensive cranial elevation and a curved cleithrobranchial ligament (CBL), and that both raking MAPs and kinematics remain entirely unmodulated-a highly unusual trait, particularly among feeding generalists. Chitala had a shorter CBL and a raking power stroke involving increased retraction of the elongated pectoral girdle during raking on goldfish. The raking MAP was also modulated in Chitala, involving an extensive overlap between muscle activity of the preparatory and power stroke phases, driven by shifts in hypaxial timing and recruitment of the hyoid protractor muscle. Sonomicrometry revealed that the protractor hyoideus muscle stored energy from retraction of the pectoral girdle for ca. 5-20 ms after onset of the power stroke and then hyper-extended. This mechanism of elastic recoil in Chitala, which amplifies retraction of the basihyal during raking on goldfish without a significant increase in recruitment of the hypaxialis, suggests a unique mechanism of modulation based on performance-enhancing changes in the design and function of the musculoskeletal system.
Design and Calibration of a Flowfield Survey Rake for Inlet Flight Research

NASA Technical Reports Server (NTRS)

Flynn, Darin C.; Ratnayake, Nalin A.; Frederick, Michael

2009-01-01

Flowfield rake was designed to quantify the flowfield for inlet research underneath NASA DFRC s F-15B airplane. Detailed loads and stress analysis performed using CFD and empirical methods to assure structural integrity. Calibration data were generated through wind tunnel testing of the rake. Calibration algorithm was developed to determine the local Mach and flow angularity at each probe. RAGE was flown November, 2008. Data is currently being analyzed.
Heat Transfer Due to Shock Wave Turbulent Boundary Layer Interactions on High Speed Weapon Systems

DTIC Science & Technology

1974-04-01

Thermocouple Location. ............ 20 8 Pressure Tap LoceL.lons ............ 23 9 Pitot Pressurp Rake Detail and Profile Measurement Stations... Pitot Pressure Profile Measurements - Pitot pressure measure- ments were made with a NASA Langley five-probe pitot pressure rake at the axial location...defined in Figure 6. Figure 9 is a schematic illustration providing the dimensions of the rake and the pitot pressure profile measure- ment stations. The
Tool wear of (Ti, Al) N-coated polycrystalline cubic boron nitride compact in cutting of hardened steel

NASA Astrophysics Data System (ADS)

Wada, Tadahiro; Hanyu, Hiroyuki

2017-11-01

Polycrystalline cubic boron nitride compact (cBN) is effective tool material for cutting hardened steel. In addition to coated high speed steel and coated cemented carbide that has long been used for cutting materials, more recently, coated cBN has also been used. In this study, to verify the effectiveness of the (Ti,Al)N-coated cBN, which is formed on the substrate of cBN by the physical vapor deposition method, the hardened steel was turned with the (Ti,Al)N-coated cBN tool at a cutting speed of 3.33, 5.00 m/s, a feed rate of 0.3 mm/rev and a depth of cut of 0.1 mm. Furthermore, the uncoated cBN, which was the substrate of the (Ti,Al)N-coated, was also used. The tool wear of the cBN tools was experimentally investigated. The following results were obtained: (1) The contact area between the rake face and the chip of the (Ti,.Al)N-coated cBN tool was smaller than that of the uncoated cBN tool. (2) The tool wear of the (Ti,Al)N-coated cBN was smaller than that of uncoated cBN. (3) The wear progress of the (Ti,Al)N-coated cBN with the main element phase of the TiCN-Al, was slower than that of the (Ti,Al)N-coated cBN with the main element phase of the TiN-Al. (4) In the case of the high cutting speed of 5.00 m/s, the tool wear of the (Ti,Al)N-coated cBN was also smaller than that of uncoated cBN. The above results clarify that the (Ti,Al)N-coated cBN can be used as a tool material in high feed cutting of hardened steel.
Tool Forces and Chip Types In Orthogonal Cutting Of Southern Hardwoods

Treesearch

G.E. Woodson

1979-01-01

Specimens (l/8 to l/4 inch thick) from 5 trees of each of 22 hardwood species were cut orthogonally at 5 inches per minute. Average parallel and normal cutting forces for various rake angles (50, 60, and 70 degrees for veneer; 10, 20, and 30 degrees for planing; 20, 30, and 40 degrees for crosscutting) were measured at three moisture contents (10 percent, 20 percent,...
The numerical study of the rake angle of impeller blade in centrifugal compressor

NASA Astrophysics Data System (ADS)

Drozdov, A.; Galerkin, Y.

2017-08-01

Investigated impellers have blade surfaces formed by straight generatrix. Blade profiles on shroud and disc surfaces are optimized by velocity diagram control (inviscid, quasi-three dimensional calculations). The blade profiles at hub and shroud blade-to-blade surfaces must be coordinated. A designer can choose the generatrix position at a trailing edge for it. The position is defined by the rake angle that is the angle between a trailing edge generatrix and a meridional plane. Two stages with 3D impellers, vaneless diffusers and return channels were investigated. Seven candidates of impellers of these stages with rake angles in range plus-minus 30 degrees were designed and investigated by quasi-three-dimensional inviscid calculation. CFD-calculations were made for the stages with these impellers. The optimal rake angle is minus 20 degrees for the high flow rate impeller due to lesser blade surface area and favorable meridian velocity field. Zero rake angle is optimal for the medium flow rate impeller where blade surface area is not so important. The combination of inviscid and viscid calculations is the informative instrument for further studies.
Sumatran orangutans differ in their cultural knowledge but not in their cognitive abilities.

PubMed

Gruber, Thibaud; Singleton, Ian; van Schaik, Carel

2012-12-04

Animal cultures are controversial because the method used to isolate culture in animals aims at excluding genetic and environmental influences rather than demonstrating social learning. Here, we analyzed these factors in parallel in captivity to determine their influences on tool use. We exposed Sumatran orangutan (Pongo abelii) orphans from tool-using and non-tool-using regions (western swamps and eastern Langkat, respectively) that differed in both genetic and cultural backgrounds to a raking task and a honey-dipping task to assess their understanding of stick use. Orangutans from both regions were equally successful in raking; however, swamp orangutans were more successful than Langkat orangutans in honey dipping, where previously acquired knowledge was required. A larger analysis suggested that the Alas River could constitute a geographical barrier to the spread of this cultural trait. Finally, honey-dipping individuals were on average less than 4 years old, but this behavior is not observed in the wild before 6 years of age. Our results suggest first that genetic differences between wild Sumatran populations cannot explain their differences in stick use; however, their performances in honey dipping support a cultural differentiation in stick knowledge. Second, the results suggest that the honey-dippers were too young when arriving at the quarantine center to have possibly mastered the behavior in the wild individually, suggesting that they arrived with preestablished mental representations of stick use or, simply put, "cultural ideas." Copyright © 2012 Elsevier Ltd. All rights reserved.
34. HILLMAN BARGE AND CONSTRUCTION COMPANY EMPLOYEES EXAMINING BARGE RAKE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. HILLMAN BARGE AND CONSTRUCTION COMPANY EMPLOYEES EXAMINING BARGE RAKE PART PATTERN, NORTHWEST MOLD LOFT - Hillman Barge & Construction Company, Paul Thomas Boulevard, Brownsville, Fayette County, PA
Tools being considered for use in freeing solar array wing of Skylab

NASA Technical Reports Server (NTRS)

1973-01-01

Engineers at the Marshall Space Flight Center examine tools that are being considered for use in freeing the solar array wing of Skylab. The device at center is a cable cutter which is operated by cable. At right is the handle end of a rod. White material taped just below the handle is buoyancy packing to make the oject weightless when submerged in water. Small object at left is the attachment head for a two-prong 'rake' device for use on the end of a pole made up of one, two or more five-foot secitons of extension rods.
Investigation of Differences Between Measured and Predicted Pressures in AEDC/VKF Hypersonic Tunnel B

DTIC Science & Technology

1997-01-01

coordinates are presented in Fig. 4b. The primary calibration data used in this paper is derived from the rake . The 42 pitot probes cov- ered a range...the lateral (YT) direction. Figures 5 and 6 show examples of the pitot pressure and total temperature rake data from a lateral survey and American...Figure 5. Rake pitot measurements, XT = 16 in. 0 10 YT, in. b. Local Mach number 20 Total Temperature Contours, R Static Temperature Contours, R
Characteristics of Perforated Diffusers at Free-Stream Mach Number 1.90

DTIC Science & Technology

1950-05-08

deg) Subscripts: 0 free stream 1 inlet entrance 2 Inlet throat 3 pitot -static rake in simulated combustion chamber 4 outlet of simulated...consisted of a 40-tube pitot -static survey rake located 0.55 combust Ion-chamber diameter downstream of the outlet of the subsonic diffuser (fig. 8(b...The rake was so designed that eaoh pitot -static tube was located at the oentroid of one of the forty equal area segments Into which the combustion
Comparison of conditional sampling and averaging techniques in a turbulent boundary layer

NASA Astrophysics Data System (ADS)

Subramanian, C. S.; Rajagopalan, S.; Antonia, R. A.; Chambers, A. J.

1982-10-01

A rake of cold wires was used in a slightly heated boundary layer to identify coherent temperature fronts. An X-wire/cold-wire arrangement was used simultaneously with the rake to provide measurements of the longitudinal and normal velocity fluctuations and temperature fluctuations. Conditional averages of these parameters and their products were obtained by application of conditional techniques (VITA, HOLE, BT, RA1, and RA3) based on the detection of temperature fronts using information obtained at only one point in space. It is found that none of the one-point detection techniques is in good quantitative agreement with the rake detection technique, the largest correspondence being 51%. Despite the relatively poor correspondence between the conditional techniques, these techniques, with the exception of HOLE, produce conditional averages that are in reasonable qualitative agreement with those deduced using the rake.
Development of a Rotating Rake Array for Boundary-Layer-Ingesting Fan-Stage Measurements

NASA Technical Reports Server (NTRS)

Wolter, John D.; Arend, David J.; Hirt, Stefanie M.; Gazzaniga, John A.

2017-01-01

The recent Boundary-Layer-Ingesting Inlet/Distortion Tolerant Fan wind tunnel experiment at NASA Glenn Research Center's 8- by 6-foot Supersonic Wind Tunnel (SWT) examined the performance of a novel inlet and fan stage that was designed to ingest the vehicle boundary layer in order to take advantage of a predicted overall propulsive efficiency benefit. A key piece of the experiment's instrumentation was a pair of rotating rake arrays located upstream and downstream of the fan stage. This paper examines the development of these rake arrays. Pre-test numerical solutions were sampled to determine placement and spacing for rake pressure and temperature probes. The effects of probe spacing and survey density on the repeatability of survey measurements was examined. These data were then used to estimate measurement uncertainty for the adiabatic efficiency.
Development of a Rotating Rake Array for Boundary-Layer-Ingesting Fan-Stage Measurements

NASA Technical Reports Server (NTRS)

Wolter, John D.; Arend, David J.; Hirt, Stefanie M.; Gazzaniga, John A.

2017-01-01

The recent Boundary-Layer-Ingesting Inlet/Distortion Tolerant Fan wind tunnel experiment at NASA Glenn Research Center's 8-foot by 6-foot supersonic wind tunnel examined the performance of a novel inlet and fan stage that was designed to ingest the vehicle boundary layer in order to take advantage of a predicted overall propulsive efficiency benefit. A key piece of the experiment's instrumentation was a pair of rotating rake arrays located upstream and downstream of the fan stage. This paper examines the development of these rake arrays. Pre-test numerical solutions were sampled to determine placement and spacing for rake pressure and temperature probes. The effects of probe spacing and survey density on the repeatability of survey measurements was examined. These data were then used to estimate measurement uncertainty for the adiabatic efficiency.
Cornice Detail of Rake, Cornice Detail of Eave, Wood DoubleHung ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Cornice Detail of Rake, Cornice Detail of Eave, Wood Double-Hung Window Details, Wood Door Details - Boxley Grist Mill, Boxley vicinity on State Route 43, Buffalo National River, Ponca, Newton County, AR
Shock Boundary Layer Interaction Flow Control with Micro Vortex Generators

DTIC Science & Technology

2011-05-01

Pitot rake ( p̄02p01 ) u = time-averaged streamwise velocity ufs = time-averaged freestream streamwise velocity u∗ = √ τw ρw = wall-shear velocity w...upstream of the normal shock-wave 2 = station 2, at the Pitot rake location I. Introduction With the exception of the scramjet, all current air-breathing...to this.7 1 shock holder near-normal shock μVGs 123 143 14 hole Pitot rake 6o x vg variable φ cylinder mounted on the centre-line 380 M ∞ =1.4
Satellite diversity and its implications on the RAKE receiver architecture for CDMA-based S-PCN's

NASA Technical Reports Server (NTRS)

Taaghol, P.; Sammut, A.; Tafazolli, R.; Evans, B. G.

1995-01-01

In this paper we examine the applicability of RAKE receivers in a mobile LEO satellite channel and identify the potential problem areas. We then proceed to investigate the possibility of a coherent combining architecture (downlink) in the presence of satellite diversity. We closely examine the path delay difference statistics of a diversity channel and propose a delay compensation scheme for the downlink in order to reduce the complexity of the user terminal. Finally, the required modifications to the conventional RAKE receiver are proposed and discussed.

F-16XL ship #1 - CAWAP outboard rakes #7 and inboard rack #3

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the #7 outboard rake and the #3 inboard rake on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.
Evaluation of beach grooming techniques on Escherichia coli density in foreshore sand at North Beach, Racine, WI

USGS Publications Warehouse

Kinzelman, Julie L.; Whitman, Richard L.; Byappanahalli, Muruleedhara N.; Jackson, Emma; Bagley, Robert C.

2003-01-01

Elevated levels of Escherichia coli(E. coli) in bathing waters at North Beach, a popular recreational site in Racine, Wisconsin, have been a persistent problem often resulting in the issuance of poor water quality advisories. Moreover, waterfowl (mostly Larus delawarensis and L. argentatus) in nearshore and offshore areas are common and may serve as non-point sources for bacterial contamination of recreational waters. Current beach management practice involves daily mechanical grooming of the nearshore sand for aesthetics and removal of hazardous debris. However, this practice has not been evaluated in terms of its effects on E. coli loading to beach sand and potential introduction to contiguous swimming water. In this study, we tested E. coli responses to three treatments: mechanical groomer, daily and twice weekly hand raking, and a control (no raking/grooming). A randomized block design consisted of replicated treatments and one control (10 each), for a total of 40 blocks sampled daily for 10 days. Foreshore sand samples were collected by hand coring to an average depth of 10 cm. Median E. colirecovered were 73 (mechanically groomed), 27 (hand-raked daily), 32 (hand-raked twice weekly), and 22 (control) colony-forming units (CFU) per gram dry weight sand. E. colicounts in sand that was groomed were significantly higher than hand rakings and control (p <0.0001), and there was no significant difference between control and raking treatments (p<0.01). This study demonstrates the beach management implications related to grooming efficacy and the importance of understanding non-point sources of bacterial contamination.
An Investigation of the McDonnell XP-85 Airplane in the Ames 40- by 80-Foot Wind Tunnel: Pressure-Distribution Tests

NASA Technical Reports Server (NTRS)

Hunton, Lynn W.; James, Harry A.

1948-01-01

Pressure measurements were made during wind-tunnel tests of the McDonnell XP-85 parasite fighter. Static-pressure orifices were located over the fuselage nose, over the canopy, along the wing root, and along the upper and lower stabilizer roots. A total-pressure and static-pressure rake was located in the turbojet engine air-intake duct. It was installed at the station where the compressor face would be located. Pressure data were obtained for two airplane conditions, clean and with skyhook extended, through a range of angle of attack and a range of yaw.
Modeling of thermal processes arising during shaping gears with internal non-involute teeth

NASA Astrophysics Data System (ADS)

Kanatnikov, N. V.; Kanatnikova, P. A.; Vlasov, V. V.; Pashmentova, A. S.

2018-03-01

The paper presents a model for predicting the thermal processes arising during shaping gears with internal non-involute teeth. The kinematics of cutting is modeled due to the analytical model. Chipping is modeled using the finite element method. The experiment is based on the method of infrared photography of the cutting process. The simulation results showed that the maximum temperatures and heat flows in the tool vary by more than 10% when the rake and clearance angels of the cutting are changed.
Rotating rake design for unique measurement of fan-generated spinning acoustic modes

NASA Technical Reports Server (NTRS)

Konno, Kevin E.; Hausmann, Clifford R.

1993-01-01

In light of the current emphasis on noise reduction in subsonic aircraft design, NASA has been actively studying the source of and propagation of noise generated by subsonic fan engines. NASA/LeRC has developed and tested a unique method of accurately measuring these spinning acoustic modes generated by an experimental fan. This mode measuring method is based on the use of a rotating microphone rake. Testing was conducted in the 9 x 15 Low-speed Wind Tunnel. The rotating rake was tested with the Advanced Ducted Propeller (ADP) model. This memorandum discusses the design and performance of the motor/drive system for the fan-synchronized rotating acoustic rake. This novel motor/drive design approach is now being adapted for additional acoustic mode studies in new test rigs as baseline data for the future design of active noise control for subsonic fan engines. Included in this memorandum are the research requirements, motor/drive specifications, test performance results, and a description of the controls and software involved.
Flight-measured base pressure coefficients for thick boundary-layer flow over an aft-facing step for Mach numbers from 0.4 to 2.5

NASA Technical Reports Server (NTRS)

Goecke, S. A.

1973-01-01

A 0.56-inch thick aft-facing step was located 52.1 feet from the leading edge of the left wing of an XB-70 airplane. A boundary-layer rake at a mirror location on the right wing was used to obtain local flow properties. Reynolds numbers were near 10 to the 8th power, resulting in a relatively thick boundary-layer. The momentum thickness ranged from slightly thinner to slightly thicker than the step height. Surface static pressures forward of the step were obtained for Mach numbers near 0.9, 1.5, 2.0, and 2.4. The data were compared with thin boundary-layer results from flight and wind-tunnel experiments and semiempirical relationships. Significant differences were found between the thick and the thin boundary-layer data.
5. UPSTREAM VIEW OF THE TRASH RAKES, GATES AND GATELIFTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. UPSTREAM VIEW OF THE TRASH RAKES, GATES AND GATE-LIFTING MECHANISMS FOR THE POST FALLS DAM AND POWERHOUSE, LOOKING NORTHWEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID
Effect of Cutting Angle and Depth of Cut on the Occurrence of Chipped Grain on Sycamore

Treesearch

Harold A. Stewart

1970-01-01

Sycamore specimens were planned with various combinations of depths of cut and rake angles. Depths of cut up to 1/16 inch had no significant effect on the occurrence of chipped grain in sycamore but rake angle did.
1. EXISTING TRASH RAKE STRUCTURE AND STEEL IBEAM TRACK, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EXISTING TRASH RAKE STRUCTURE AND STEEL I-BEAM TRACK, LOOKING EAST/NORTHEAST. - Washington Water Power Spokane River Upper Falls Hydroelectric Development, Gates & Gate-Lifting Mechanisms, Spokane River, approximately 0.5 mile northeast of intersection of Spokane Falls Boulevard & Post Street, Spokane, Spokane County, WA
A Link-Level Simulator of the cdma2000 Reverse-Link Physical Layer

PubMed Central

Gharavi, H.; Chin, F.; Ban, K.; Wyatt-Millington, R.

2003-01-01

The cdma2000 system is an evolutionary enhancement of the IS-95 standards which support 3G services defined by the International Telecommunications Union (ITU). cdma2000 comes in two phases: 1XRTT and 3XRTT (1X and 3X indicates the number of 1.25 MHz wide radio carrier channels used and RTT stands for Radio Transmission Technology). The cdma2000 1XRTT, which operates within a 1.25 MHz bandwidth, can be utilized in existing IS-95 CDMA channels as it uses the same bandwidth, while 3XRTT requires the commitment of 5 MHz bandwidth to support higher data rates. This paper describes a software model implementation of the cdma2000 reverse link and its application for evaluating the effect of rake receiver design parameters on the system performance under various multipath fading conditions. The cdma2000 models were developed at the National Institute of Standards and Technology (NIST), using SPW (Signal Processing Worksystem) commercial software tools. The model has been developed in a generic manner that includes all the reverse link six radio configurations and their corresponding data rates, according to cdma2000 specifications. After briefly reviewing the traffic channel characteristics of the cdma2000 reverse link (subscriber to base station), the paper discusses the rake receiver implementation including an ideal rake receiver. It then evaluates the performance of each receiver for a Spreading Rate 3 (3XRTT) operation, which is considered as a true “3G” cdma2000 technology. These evaluations are based on the vehicular IMT-2000 (International Mobile Telecommunication 2000) channel model using the link budget defined in cdma2000 specifications for the reverse link. PMID:27413613
An Analysis of Thrust Normalization of Ground Flowfield Pressures, Temperatures, and Velocities, for an AV-8B -408 Harrier During Hover

NASA Technical Reports Server (NTRS)

Naumowicz, Tim; Hange, Craig; Olson, Lawrence E. (Technical Monitor)

1998-01-01

An external environment test for an AV-8B Harrier during hover and vertical operations was conducted at NAWCAD at Patuxent River, Maryland in July 1997. Four boundary layer rakes were instrumented with static and total pressures, and thermocouples for measuring temperatures. These rakes were installed at 30, 50, 75, and 100 foot from the hover center. The 50 ft and 100 ft rakes were offset 20 deg from the other two to minimize interference effects. In order to measure a complete flowfield footprint, it was necessary to have the Harrier change its heading relative to the rakes from 0 to 180 deg. A 20 deg increment in azimuth was used. This permitted the four rakes to measure the flowfield at 72 locations relative to the aircraft. However, as the Harrier burns fuel, the hover thrust must be reduced by the pilot in order to maintain a constant height above ground. The typical test procedure employed was: (1) vertical takeoff at an initial heading; (2) 20 second hover dwell at that heading; (3) pedal turn to a second heading, followed by a 20 second dwell hover; (4) pedal turn to a third heading, followed by a 20 second dwell hover; and (5) vertical landing at the third heading. Additional information is contained in the original extended abstract.
9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...
9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...
9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

... nonhuman primates come in contact must be spot-cleaned daily and sanitized in accordance with § 3.84 of... bedding, sand, gravel, grass, or other similar material, and planted enclosures must be raked or spot.... Contaminated material must be removed or replaced whenever raking and spot cleaning does not eliminate odors...
9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...
Asphalt Raking. Instructor Manual. Trainee Manual.

ERIC Educational Resources Information Center

Laborers-AGC Education and Training Fund, Pomfret Center, CT.

This packet consists of the instructor and trainee manuals for an asphalt raking course. The instructor manual contains a course schedule for 4 days of instruction, content outline, and instructor outline. The trainee manual is divided into five sections: safety, asphalt basics, placing methods, repair and patching, and clean-up and maintenance.…
Implementing virtual reality interfaces for the geosciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bethel, W.; Jacobsen, J.; Austin, A.

1996-06-01

For the past few years, a multidisciplinary team of computer and earth scientists at Lawrence Berkeley National Laboratory has been exploring the use of advanced user interfaces, commonly called {open_quotes}Virtual Reality{close_quotes} (VR), coupled with visualization and scientific computing software. Working closely with industry, these efforts have resulted in an environment in which VR technology is coupled with existing visualization and computational tools. VR technology may be thought of as a user interface. It is useful to think of a spectrum, ranging the gamut from command-line interfaces to completely immersive environments. In the former, one uses the keyboard to enter threemore » or six-dimensional parameters. In the latter, three or six-dimensional information is provided by trackers contained either in hand-held devices or attached to the user in some fashion, e.g. attached to a head-mounted display. Rich, extensible and often complex languages are a vehicle whereby the user controls parameters to manipulate object position and location in a virtual world, but the keyboard is the obstacle in that typing is cumbersome, error-prone and typically slow. In the latter, the user can interact with these parameters by means of motor skills which are highly developed. Two specific geoscience application areas will be highlighted. In the first, we have used VR technology to manipulate three-dimensional input parameters, such as the spatial location of injection or production wells in a reservoir simulator. In the second, we demonstrate how VR technology has been used to manipulate visualization tools, such as a tool for computing streamlines via manipulation of a {open_quotes}rake.{close_quotes} The rake is presented to the user in the form of a {open_quotes}virtual well{close_quotes} icon, and provides parameters used by the streamlines algorithm.« less
Reproductive ecology of American Oystercatchers nesting on shell rakes

USGS Publications Warehouse

Jodice, Patrick G.R.; Thibault, Janet M.; Collins, S.A.; Spinks, Mark D.; Sanders, Felicia J.

2014-01-01

Degradation of nesting habitat for coastal birds has led to the use of nontraditional nesting habitat. The American Oystercatcher (Haematopus palliatus) is listed as a "Species of High Concern'' by the U. S. Shorebird Conservation Plan and is declining in the southern portion of its U. S. breeding range, where ~ 50% of breeding oystercatchers nest on shell substrate instead of beachfront habitat. We measured daily survival rates during incubation and chick rearing in shell rake habitats over five breeding seasons in the Cape Romain region of South Carolina, USA. Of 354 nesting attempts monitored, 16.1% hatched at least one egg. During incubation, daily survival rate was 0.938, corresponding to 22.8% success to hatching (nest success). For broods, daily survival was 0.991, or 74.0% success from hatching to fledging. Productivity in the Cape Romain region is primarily being lost during the incubation phase, when nests are exposed to overwash and predation. Mobile chicks may, however, be able to avoid flood events or predators by relocating to higher or more protected portions of a shell rake. Based on comparative data for American Oystercatchers from elsewhere in their range, it does not appear that shell rakes in the Cape Romain region are inferior breeding habitat. Our data suggest that conservation actions targeting nest and chick loss from flooding and predation have the greatest opportunity to enhance reproductive success in this core breeding area, and that an assessment of the availability, structure, avian use, and protection status of shell rakes is warranted.
Flight Test Results from the Rake Airflow Gage Experiment on the F-15B Airplane

NASA Technical Reports Server (NTRS)

Frederick, Michael A.; Ratnayake, Nalin A.

2010-01-01

The Rake Airflow Gage Experiment involves a flow-field survey rake that was flown on the Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center using the Dryden F-15B research test bed airplane. The objective of this flight test was to ascertain the flow-field angularity, local Mach number profile, total pressure distortion, and dynamic pressure at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment. This new mixed-compression, supersonic inlet is planned for flight test in the near term. Knowledge of the flow-field characteristics at this location underneath the airplane is essential to flight test planning and computational modeling of the new inlet, and it is also applicable for future propulsion systems research that may use the Propulsion Flight Test Fixture. This report describes the flight test preparation and execution, and the local flowfield properties calculated from pressure measurements of the rake. Data from the two Rake Airflow Gage Experiment research flights demonstrate that the F-15B airplane, flying at a free-stream Mach number of 1.65 and a pressure altitude of 40,000 ft, would achieve the desired local Mach number for the future inlet flight test. Interface plane distortion levels of 2 percent and a local angle of attack of 2 were observed at this condition. Alternative flight conditions for future testing and an exploration of certain anomalous data also are provided.
Flight Test Results from the Rake Airflow Gage Experiment on the F-15B Airplane

NASA Technical Reports Server (NTRS)

Frederick, Michael A.; Ratnayake, Nalin A.

2011-01-01

The Rake Airflow Gage Experiment involves a flow-field survey rake that was flown on the Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center using the Dryden F-15B research test bed airplane. The objective of this flight test was to ascertain the flow-field angularity, local Mach number profile, total pressure distortion, and dynamic pressure at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment. This new mixed-compression, supersonic inlet is planned for flight test in the near term. Knowledge of the flow-field characteristics at this location underneath the airplane is essential to flight test planning and computational modeling of the new inlet, an< it is also applicable for future propulsion systems research that may use the Propulsion Flight Test Fixture. This report describes the flight test preparation and execution, and the local flow-field properties calculated from pressure measurements of the rake. Data from the two Rake Airflow Gage Experiment research flights demonstrate that the F-15B airplane, flying at a free-stream Mach number of 1.65 and a pressure altitude of 40,000 ft, would achieve the desired local Mach number for the future inlet flight test. Interface plane distortion levels of 2 percent and a local angle of attack of -2 deg were observed at this condition. Alternative flight conditions for future testing and an exploration of certain anomalous data also are provided.

Prediction Of Abrasive And Diffusive Tool Wear Mechanisms In Machining

NASA Astrophysics Data System (ADS)

Rizzuti, S.; Umbrello, D.

2011-01-01

Tool wear prediction is regarded as very important task in order to maximize tool performance, minimize cutting costs and improve the quality of workpiece in cutting. In this research work, an experimental campaign was carried out at the varying of cutting conditions with the aim to measure both crater and flank tool wear, during machining of an AISI 1045 with an uncoated carbide tool P40. Parallel a FEM-based analysis was developed in order to study the tool wear mechanisms, taking also into account the influence of the cutting conditions and the temperature reached on the tool surfaces. The results show that, when the temperature of the tool rake surface is lower than the activation temperature of the diffusive phenomenon, the wear rate can be estimated applying an abrasive model. In contrast, in the tool area where the temperature is higher than the diffusive activation temperature, the wear rate can be evaluated applying a diffusive model. Finally, for a temperature ranges within the above cited values an adopted abrasive-diffusive wear model furnished the possibility to correctly evaluate the tool wear phenomena.
Thermocouple Rakes for Measuring Boundary Layer Flows Extremely Close to Surface

NASA Technical Reports Server (NTRS)

Hwang, Danny P.; Fralick, Gustave C.; Martin, Lisa C.; Blaha, Charles A.

2001-01-01

Of vital interest to aerodynamic researchers is precise knowledge of the flow velocity profile next to the surface. This information is needed for turbulence model development and the calculation of viscous shear force. Though many instruments can determine the flow velocity profile near the surface, none of them can make measurements closer than approximately 0.01 in. from the surface. The thermocouple boundary-layer rake can measure much closer to the surface than conventional instruments can, such as a total pressure boundary layer rake, hot wire, or hot film. By embedding the sensors (thermocouples) in the region where the velocity is equivalent to the velocity ahead of a constant thickness strut, the boundary-layer flow profile can be obtained. The present device fabricated at the NASA Glenn Research Center microsystem clean room has a heater made of platinum and thermocouples made of platinum and gold. Equal numbers of thermocouples are placed both upstream and downstream of the heater, so that the voltage generated by each pair at the same distance from the surface is indicative of the difference in temperature between the upstream and downstream thermocouple locations. This voltage differential is a function of the flow velocity, and like the conventional total pressure rake, it can provide the velocity profile. In order to measure flow extremely close to the surface, the strut is made of fused quartz with extremely low heat conductivity. A large size thermocouple boundary layer rake is shown in the following photo. The latest medium size sensors already provide smooth velocity profiles well into the boundary layer, as close as 0.0025 in. from the surface. This is about 4 times closer to the surface than the previously used total pressure rakes. This device also has the advantage of providing the flow profile of separated flow and also it is possible to measure simultaneous turbulence levels within the boundary layer.
Numerical Technique for Analyzing Rotating Rake Mode Measurements in a Duct With Passive Treatment and Shear Flow

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Sutliff, Daniel L.

2007-01-01

A technique is presented for the analysis of measured data obtained from a rotating microphone rake system. The system is designed to measure the interaction modes of ducted fans. A Fourier analysis of the data from the rotating system results in a set of circumferential mode levels at each radial location of a microphone inside the duct. Radial basis functions are then least-squares fit to this data to obtain the radial mode amplitudes. For ducts with soft walls and mean flow, the radial basis functions must be numerically computed. The linear companion matrix method is used to obtain both the eigenvalues of interest, without an initial guess, and the radial basis functions. The governing equations allow for the mean flow to have a boundary layer at the wall. In addition, a nonlinear least-squares method is used to adjust the wall impedance to best fit the data in an attempt to use the rotating system as an in-duct wall impedance measurement tool. Simulated and measured data are used to show the effects of wall impedance and mean flow on the computed results.
A Mode Propagation Database Suitable for Code Validation Utilizing the NASA Glenn Advanced Noise Control Fan and Artificial Sources

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2014-01-01

The NASA Glenn Research Center's Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. A series of tests were performed primarily for the use of code validation and tool validation. Rotating Rake mode measurements were acquired for parametric sets of: (i) mode blockage, (ii) liner insertion loss, (iii) short ducts, and (iv) mode reflection.
A Mode Propagation Database Suitable for Code Validation Utilizing the NASA Glenn Advanced Noise Control Fan and Artificial Sources

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2014-01-01

The NASA Glenn Research Center's Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. A series of tests were performed primarily for the use of code validation and tool validation. Rotating Rake mode measurements were acquired for parametric sets of: (1) mode blockage, (2) liner insertion loss, (3) short ducts, and (4) mode reflection.
10. CLOSEUP VIEW OF THE TRASH RAKES, THEIR LIFTING MECHANISM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. CLOSE-UP VIEW OF THE TRASH RAKES, THEIR LIFTING MECHANISM (RIGHT FOREGROUND), AND CLUTCHES THAT OPEN AND CLOSE THE SIX INTAKE GATES ON THE POST FALLS POWERHOUSE, LOOKING WEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID
A survey of aerobraking orbital transfer vehicle design concepts

NASA Technical Reports Server (NTRS)

Park, Chul

1987-01-01

The five existing design concepts of the aerobraking orbital transfer vehicle (namely, the raked sphere-cone designs, conical lifting-brake, raked elliptic-cone, lifting-body, and ballute) are reviewed and critiqued. Historical backgrounds, and the geometrical, aerothermal, and operational features of these designs are reviewed first. Then, the technological requirements for the vehicle (namely, navigation, aerodynamic stability and control, afterbody flow impingement, nonequilibrium radiation, convective heat-transfer rates, mission abort and multiple atmospheric passes, transportation and construction, and the payload-to-vehicle weight requirements) are delineated by summarizing the recent advancements made on these issues. Each of the five designs are critiqued and rated on these issues. The highest and the lowest ratings are given to the raked sphere-cone and the ballute design, respectively.
Comparison of Engine/Inlet Distortion Measurements with MEMS and ESP Pressure Sensors

NASA Technical Reports Server (NTRS)

Soto, Hector L.; Hernandez, Corey D.

2004-01-01

A study of active-flow control in a small-scale boundary layer ingestion inlet was conducted at the NASA Langley Basic Aerodynamic Research Tunnel (BART). Forty MEMS pressure sensors, in a rake style configuration, were used to examine both the mean (DC) and high frequency (AC) components of the total pressure across the inlet/engine interface plane. The mean component was acquired and used to calculate pressure distortion. The AC component was acquired separately, at a high sampling rate, and is used to study the unsteady effects of the active-flow control. An identical total pressure rake, utilizing an Electronically Scanned Pressure (ESP) system, was also used to calculate distortion; a comparison of the results obtained using the two rakes is presented.
Intensive straw harvesting, fertilization, and fertilizer source affect nitrogen mineralization and soil labile carbon of a loblolly pine plantation

Treesearch

K. Ellum; H.O. Liechty; M.A. Blazier

2013-01-01

Straw harvesting can supplement traditional revenues generated by loblolly pine (Pinus taeda L.) plantation management. However, repeated raking may alter soil properties and nutrition. In northcentral Louisiana, a study was conducted to evaluate the long-term effects of intensive straw raking and fertilizer source (inorganic or organic) on nitrogen...
Evaluation of Federal Aviation Administration Engine Exhaust Sampling Rake.

DTIC Science & Technology

1977-06-01

Engine exit total pressure - Pt7 " High turbine discharge temperature - Tt65,6 . Engine exit total temperature - Tt7 - Burner pressure - Ps4 0 Total...illustrated by Figure 22, a plot of Ps4 /Pt7 (expansion thru the turbine) vs. EPR (Pt7/Pt2). This plot indicates that the ECCP rake has no measurable effect on
67. September 1913 "No. 103. Oil being applied and raked ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

67. September 1913 "No. 103. Oil being applied and raked in, oil treated earth surface, experimental section. The frame in foreground was 1 x 5 yards, each square yard being indicated thereon, by which it was possible to determine the amount of oil placed in each square yard." - Crater Lake National Park Roads, Klamath Falls, Klamath County, OR
Design and Calibration of a Flowfield Survey Rake for Inlet Flight Research

NASA Technical Reports Server (NTRS)

Flynn, Darin C.; Ratnayake, Nalin A.; Frederick, Michael

2009-01-01

The Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center is a unique test platform available for use on NASA's F-15B aircraft, tail number 836, as a modular host for a variety of aerodynamics and propulsion research. For future flight data from this platform to be valid, more information must be gathered concerning the quality of the airflow underneath the body of the F-15B at various flight conditions, especially supersonic conditions. The flow angularity and Mach number must be known at multiple locations on any test article interface plane for measurement data at these locations to be valid. To determine this prerequisite information, flight data will be gathered in the Rake Airflow Gauge Experiment using a custom-designed flowfield rake to probe the airflow underneath the F-15B at the desired flight conditions. This paper addresses the design considerations of the rake and probe assembly, including the loads and stress analysis using analytical methods, computational fluid dynamics, and finite element analysis. It also details the flow calibration procedure, including the completed wind-tunnel test and posttest data reduction, calibration verification, and preparation for flight-testing.
Cone-Probe Rake Design and Calibration for Supersonic Wind Tunnel Models

NASA Technical Reports Server (NTRS)

Won, Mark J.

1999-01-01

A series of experimental investigations were conducted at the NASA Langley Unitary Plan Wind Tunnel (UPWT) to calibrate cone-probe rakes designed to measure the flow field on 1-2% scale, high-speed wind tunnel models from Mach 2.15 to 2.4. The rakes were developed from a previous design that exhibited unfavorable measurement characteristics caused by a high probe spatial density and flow blockage from the rake body. Calibration parameters included Mach number, total pressure recovery, and flow angularity. Reference conditions were determined from a localized UPWT test section flow survey using a 10deg supersonic wedge probe. Test section Mach number and total pressure were determined using a novel iterative technique that accounted for boundary layer effects on the wedge surface. Cone-probe measurements were correlated to the surveyed flow conditions using analytical functions and recursive algorithms that resolved Mach number, pressure recovery, and flow angle to within +/-0.01, +/-1% and +/-0.1deg , respectively, for angles of attack and sideslip between +/-8deg. Uncertainty estimates indicated the overall cone-probe calibration accuracy was strongly influenced by the propagation of measurement error into the calculated results.
Multiple Access Interference Reduction Using Received Response Code Sequence for DS-CDMA UWB System

NASA Astrophysics Data System (ADS)

Toh, Keat Beng; Tachikawa, Shin'ichi

This paper proposes a combination of novel Received Response (RR) sequence at the transmitter and a Matched Filter-RAKE (MF-RAKE) combining scheme receiver system for the Direct Sequence-Code Division Multiple Access Ultra Wideband (DS-CDMA UWB) multipath channel model. This paper also demonstrates the effectiveness of the RR sequence in Multiple Access Interference (MAI) reduction for the DS-CDMA UWB system. It suggests that by using conventional binary code sequence such as the M sequence or the Gold sequence, there is a possibility of generating extra MAI in the UWB system. Therefore, it is quite difficult to collect the energy efficiently although the RAKE reception method is applied at the receiver. The main purpose of the proposed system is to overcome the performance degradation for UWB transmission due to the occurrence of MAI during multiple accessing in the DS-CDMA UWB system. The proposed system improves the system performance by improving the RAKE reception performance using the RR sequence which can reduce the MAI effect significantly. Simulation results verify that significant improvement can be obtained by the proposed system in the UWB multipath channel models.
Low gravity liquid level sensor rake

NASA Technical Reports Server (NTRS)

Grayson, Gary D. (Inventor); Craddock, Jeffrey C. (Inventor)

2003-01-01

The low gravity liquid level sensor rake measures the liquid surface height of propellant in a propellant tank used in launch and spacecraft vehicles. The device reduces the tendency of the liquid propellant to adhere to the sensor elements after the bulk liquid level has dropped below a given sensor element thereby reducing the probability of a false liquid level measurement. The liquid level sensor rake has a mast attached internal to a propellant tank with an end attached adjacent the tank outlet. Multiple sensor elements that have an arm and a sensor attached at a free end thereof are attached to the mast at locations selected for sensing the presence or absence of the liquid. The sensor elements when attached to the mast have a generally horizontal arm and a generally vertical sensor.
A Future Moon Mission: Curatorial Statistics on Regolith Fragments Applicable to Sample Collection by Raking

NASA Technical Reports Server (NTRS)

Allton, J. H.; Bevill, T. J.

2003-01-01

The strategy of raking rock fragments from the lunar regolith as a means of acquiring representative samples has wide support due to science return, spacecraft simplicity (reliability) and economy [3, 4, 5]. While there exists widespread agreement that raking or sieving the bulk regolith is good strategy, there is lively discussion about the minimum sample size. Advocates of consor-tium studies desire fragments large enough to support petrologic and isotopic studies. Fragments from 5 to 10 mm are thought adequate [4, 5]. Yet, Jolliff et al. [6] demonstrated use of 2-4 mm fragments as repre-sentative of larger rocks. Here we make use of cura-torial records and sample catalogs to give a different perspective on minimum sample size for a robotic sample collector.
Survivorship of raked and unraked trees through prescribed fires in conifer forests in northeastern California

Treesearch

William F. Laudenslayer; George N. Steger; Jonathan Arnold

2008-01-01

Large diameter, old trees are an important component of functioning forests, as they provide habitat for many wildlife species and add value to the scenery along roads and trails that cross our National Forests and Parks. Tree mortality, from prescribed or wild fire, is of great concern to forests managers, especially mortality of those of large diameter. Raking away...
Blind information-theoretic multiuser detection algorithms for DS-CDMA and WCDMA downlink systems.

PubMed

Waheed, Khuram; Salem, Fathi M

2005-07-01

Code division multiple access (CDMA) is based on the spread-spectrum technology and is a dominant air interface for 2.5G, 3G, and future wireless networks. For the CDMA downlink, the transmitted CDMA signals from the base station (BS) propagate through a noisy multipath fading communication channel before arriving at the receiver of the user equipment/mobile station (UE/MS). Classical CDMA single-user detection (SUD) algorithms implemented in the UE/MS receiver do not provide the required performance for modern high data-rate applications. In contrast, multi-user detection (MUD) approaches require a lot of a priori information not available to the UE/MS. In this paper, three promising adaptive Riemannian contra-variant (or natural) gradient based user detection approaches, capable of handling the highly dynamic wireless environments, are proposed. The first approach, blind multiuser detection (BMUD), is the process of simultaneously estimating multiple symbol sequences associated with all the users in the downlink of a CDMA communication system using only the received wireless data and without any knowledge of the user spreading codes. This approach is applicable to CDMA systems with relatively short spreading codes but becomes impractical for systems using long spreading codes. We also propose two other adaptive approaches, namely, RAKE -blind source recovery (RAKE-BSR) and RAKE-principal component analysis (RAKE-PCA) that fuse an adaptive stage into a standard RAKE receiver. This adaptation results in robust user detection algorithms with performance exceeding the linear minimum mean squared error (LMMSE) detectors for both Direct Sequence CDMA (DS-CDMA) and wide-band CDMA (WCDMA) systems under conditions of congestion, imprecise channel estimation and unmodeled multiple access interference (MAI).
Influence of intertidal recreational fisheries and 'bouchot' mussel culture on bivalve recruitment.

PubMed

Toupoint, Nicolas; Barbier, Pierrick; Tremblay, Réjean; Archambault, Philippe; McKindsey, Christopher W; Winkler, Gesche; Meziane, Tarik; Olivier, Frédéric

2016-06-01

In coastal environments, fishing and aquaculture may be important sources of disturbance to ecosystem functioning, the quantification of which must be assessed to make them more sustainable. In the Chausey Archipelago, France, recreational fishing and commercial shellfish farming are the only two evident anthropogenic activities, dominated by bivalve hand-raking and 'bouchot' mussel culture, respectively. This study evaluates the impact of both activities on bivalve recruitment dynamics by comparing primary recruitment intensity (short-term effect) and recruitment efficiency (medium-term effect) by sampling bivalves in reference (undisturbed) and disturbed (i.e. subjected to hand-raking or in 'bouchot' mussel culture areas) parcels throughout and at the end of the recruitment season, respectively. Specific hypotheses evaluated were that (H1) bivalve hand-raking negatively affects bivalve recruitment and that (H2) 'bouchot' mussel culture promotes bivalve recruitment. Patterns in bivalve community structure in reference parcels (i.e. natural pattern) differed between initial and final recruitment, underlining the great importance of early post-settlement processes, particularly secondary dispersal. Primary recruitment intensity was inhibited in hand-raking parcels whereas it was promoted in 'bouchot' mussel culture parcels, but the effect on recruitment efficiency was muted for both activities due to post-settlement processes. Nevertheless, the importance of effects that occur during the first step of recruitment should not be ignored as they may affect bivalve communities and induce immediate consequences on the trophic web through a cascade effect. Finally, it is highlighted that hand-raking damages all life stages of the common cockle Cerastoderma edule, one of the major target species, suggesting that this activity should be managed with greater caution than is currently done. Copyright © 2016 Elsevier Ltd. All rights reserved.
F-16XL ship #1 outboard rake #7

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the #7 outboard rake on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

Design of a constant tension thermocouple rake suitable for flame studies

NASA Technical Reports Server (NTRS)

Ahuja, Sandeep; Miller, David L.

1993-01-01

An improved, spring-loaded thermocouple rake, suitable for studying flame structure, has been designed. This design keeps the thermocouple under tension thereby ensuring that the thermocouple does not droop due to the thermal expansion of the sensing wire when inserted in the flame. The present design allows the usage of thermocouple wire as small as 0.0508 mm and relative ease in changing thermocouple wire.
Noise Identification in a Hot Transonic Jet Using Low-Dimensional Methods

DTIC Science & Technology

2008-03-01

calibration between the nozzle static pressure (transducer) and total pressure ( pitot probe) reveals a nearly linear relationship between the two, exhibiting... rakes of hot-wires. Multi-point correlations of velocity components coupled with assumptions of homogeneity and periodicity in the jet flow flied...axisymmetric incompressible jet at one downstream position using an in-house designed rake of 138 hot-wires. The experiment was then carried out at multiple
Calibration of averaging total pressure flight wake rake and natural-laminar-flow airfoil drag certification

NASA Technical Reports Server (NTRS)

Irani, E.; Snyder, M. H.

1988-01-01

An averaging total pressure wake rake used by the Cessna Aircraft Company in flight tests of a modified 210 airplane with a laminar flow wing was calibrated in wind tunnel tests against a five-tube pressure probe. The model generating the wake was a full-scale model of the Cessna airplane wing. Indications of drag trends were the same for both instruments.
Pre-Flight Ground Testing of the Full-Scale HIFiRE-1 at Fully Duplicated Flight Conditions

DTIC Science & Technology

2008-05-14

survey rake installed in the test section to measure X ... -------- pitot pressure, static pressure and stagnation point heat transfer in . the...equilibrium at Figure 17. Photograph of Pitot Rake Assembly all points. This is a safe assumption, as the pressures and Mounted Inside Test Section of...measurement technique in supersonic and hypersonic test facilities, and the small size of the sensing element coupled with the insulating substrate
The AFFDL-Nielsen Flow-Field Study

DTIC Science & Technology

1976-04-01

76-18 1.0 INTRODUCTION This investigation was conducted in the von K ~ n Gas Dynamics Facility (VKF) Supersonic Wind Tunnel (A) for Nielsen...flow field-surveys, using a cone probe rake to determine the local velocity field; (2) pressure distributions on a store model; and (3) force and...moment data on a store model. In addition, free-stream (interference-free) data were obtained with the probe rake and on the force and pressure store
A flammability study of thin plastic film materials

NASA Technical Reports Server (NTRS)

Skinner, S. Ballou

1990-01-01

The Materials Science Laboratory at the Kennedy Space Center presently conducts flammability tests on thin plastic film materials by using a small needle rake method. Flammability data from twenty-two thin plastic film materials were obtained and cross-checked by using three different testing methods: (1) the presently used small needle rake; (2) the newly developed large needle rake; and (3) the previously used frame. In order to better discern the melting-burning phenomenon of thin plastic film material, five additional specific experiments were performed. These experiments determined the following: (1) the heat sink effect of each testing method; (2) the effect of the burn angle on the burn length or melting/shrinkage length; (3) the temperature profile above the ignition source; (4) the melting point and the fire point of each material; and (5) the melting/burning profile of each material via infrared (IR) imaging. The results of these experimentations are presented.
F-16XL ship #1 - CAWAP boundary layer rakes and hot film on left wing

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the boundary layer hot film and the boundary layer rakes on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.
F-16XL ship #1 - CAWAP outboard rake #7

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the #7 outboard rake on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.
Ductile-regime turning of germanium and silicon

NASA Technical Reports Server (NTRS)

Blake, Peter N.; Scattergood, Ronald O.

1989-01-01

Single-point diamond turning of silicon and germanium was investigated in order to clarify the role of cutting depth in coaxing a ductile chip formation in normally brittle substances. Experiments based on the rapid withdrawal of the tool from the workpiece have shown that microfracture damage is a function of the effective depth of cut (as opposed to the nominal cutting depth). In essence, damage created by the leading edge of the tool is removed several revolutions later by lower sections of the tool edge, where the effective cutting depth is less. It appears that a truly ductile cutting response can be achieved only when the effective cutting depth, or critical chip thickness, is less than about 20 nm. Factors such as tool rake angle are significant in that they will affect the actual value of the critical chip thickness for transition from brittle to ductile response. It is concluded that the critical chip thickness is an excellent parameter for measuring the effects of machining conditions on the ductility of the cut and for designing tool-workpiece geometry in both turning and grinding.
Numerical modelling of orthogonal cutting: application to woodworking with a bench plane.

PubMed

Nairn, John A

2016-06-06

A numerical model for orthogonal cutting using the material point method was applied to woodcutting using a bench plane. The cutting process was modelled by accounting for surface energy associated with wood fracture toughness for crack growth parallel to the grain. By using damping to deal with dynamic crack propagation and modelling all contact between wood and the plane, simulations could initiate chip formation and proceed into steady-state chip propagation including chip curling. Once steady-state conditions were achieved, the cutting forces became constant and could be determined as a function of various simulation variables. The modelling details included a cutting tool, the tool's rake and grinding angles, a chip breaker, a base plate and a mouth opening between the base plate and the tool. The wood was modelled as an anisotropic elastic-plastic material. The simulations were verified by comparison to an analytical model and then used to conduct virtual experiments on wood planing. The virtual experiments showed interactions between depth of cut, chip breaker location and mouth opening. Additional simulations investigated the role of tool grinding angle, tool sharpness and friction.
Investigation of Shock Diffusers at Mach Number 1.85. 2 - Projecting Double-Shock Cones

DTIC Science & Technology

1947-06-17

pitot - static rake located as shown in figure 1(a). Total-pressure recoveries were measured for a series of tip projections varied in minimum steps...is shown. The position of the pitot -static rake with which these distributions were .measured is shown in figure 1(a). The data points correspond...Schroeder SUMMARY An Investigation has "been undertaken in the Cleveland 18- by 18-Inch, supersonic tunnel to determine the total-pressure
Investigation of Shock Diffusers at Mach Number 1.85. 1 - Projecting Single Shock Cones

DTIC Science & Technology

1947-06-17

cylindrical simulated combustion chamber was used to vary the outlet area of the flow through the diffuser. The pitot -static rake , located as shown in the...Simulated combustion u chamber A 90° W •—Conical damper S Static-pressure orifice ps pitot -static "" rake ’ NATIONAL ADVISORY...recoveries were obtained with subsonic entrance flow. INTRODCJCTION For efficient conversion of the kinetic energy of a supersonic air stream into ram
Comparison of wind tunnel and flight test afterbody and nozzle pressures for a twin-jet fighter aircraft at transonic speeds

NASA Technical Reports Server (NTRS)

Nugent, Jack; Pendergraft, Odis C., Jr.

1987-01-01

Afterbody and nozzle pressures measured on a 1/12-scale model and in flight on a twin-jet fighter aircraft were compared as Mach number varied from 0.6 to 1.2, Reynolds number from 17.5 million to 302.5 million, and angle of attack from 1 to 7 deg. At Mach 0.6 and 0.8, nozzle pressure coefficient distributions and nozzle axial force coefficients agreed and showed good recompression. At Mach 0.9 and 1.2, flow complexity caused a loss in recompression for both flight and wind tunnel nozzle data. The flight data exhibited less negative values of pressure coefficient and lower axial force coefficients than did the wind tunnel data. Reynolds number effects were noted only at these Mach numbers. Jet temperature and mass flux ratio did not affect the comparisons of nozzle axial flow coefficient. At subsonic speeds, the levels of pressure coefficient distributions on the upper fuselage and lower nacelle surfaces for flight were less negative than those for the model. The model boundary layer thickness at the aft rake station exceeded that for the forward rake station and increased with increasing angle of attack. The flight boundary layer thickness at the aft rake station was less than that for the forward rake station and decreased with increasing angle of attack.
Calculation of skiving cutter blade

NASA Astrophysics Data System (ADS)

Xu, Lei; Lao, Qicheng; Shang, Zhiyi

2018-05-01

The gear skiving method is a kind of gear machining technology with high efficiency and high precision. According to the method of gear machining, a method for calculating the blade of skiving cutter in machining an involute gear is proposed. Based on the principle of meshing gear and the kinematic relationship between the machined flank and the gear skiving, the mathematical model of skiving for machining the internal gear is built and the gear tooth surface is obtained by solving the meshing equation. The mathematical model of the gear blade curve of the skiving cutter is obtained by choosing the proper rake face and the cutter tooth surface for intersection. Through the analysis of the simulation of the skiving gear, the feasibility and correctness of the skiving cutter blade design are verified.
Modular Rake of Pitot Probes

NASA Technical Reports Server (NTRS)

Dunlap, Timothy A.; Henry, Michael W.; Homyk, Raymond P.

2004-01-01

The figure presents selected views of a modular rake of 17 pitot probes for measuring both transient and steady-state pressures in a supersonic wind tunnel. In addition to pitot tubes visible in the figure, the probe modules contain (1) high-frequency dynamic-pressure transducers connected through wires to remote monitoring circuitry and (2) flow passages that lead to tubes that, in turn, lead to remote steady-state pressure transducers. Prior pitot-probe rakes were fabricated as unitary structures, into which the individual pitot probes were brazed. Repair or replacement of individual probes was difficult, costly, and time-consuming because (1) it was necessary to remove entire rakes in order to unbraze individual malfunctioning probes and (2) the heat of unbrazing a failed probe and of brazing a new probe in place could damage adjacent probes. In contrast, the modules in the present probe are designed to be relatively quickly and easily replaceable with no heating and, in many cases, without need for removal of the entire rake from the wind tunnel. To remove a malfunctioning probe, one first removes a screw-mounted V-cross-section cover that holds the probe and adjacent probes in place. Then one removes a screw-mounted cover plate to gain access to the steady-state pressure tubes and dynamicpressure wires. Next, one disconnects the tube and wires of the affected probe. Finally, one installs a new probe in the reverse of the aforementioned sequence. The wire connections can be made by soldering, but to facilitate removal and installation, they can be made via miniature plugs and sockets. The connections between the probe flow passages and the tubes leading to the remote pressure sensors can be made by use of any of a variety of readily available flexible tubes that can be easily pulled off and slid back on for removal and installation, respectively.
Laminar Boundary Layer Stability Measurements at Mach 7 Including Wall Temperature Effects

DTIC Science & Technology

1977-11-01

Diagnostics were done by a four-probe rake bearing a pitot tube, a To probe and two hot films - a boundary layer hot film probe (BLHF) and a freestream hot...tunnel. Inset shows hot film probe close to the surface with second probe positioned higher to sample simultaneously the frcestream turbulence ( pitot ... rake away from the surface by small increments and taking readings at each stop. The readings were simultaneously recorded and reduced by the Tunnel B
Cross-Grain Knife Planing Improves Surface Quality and Utilization of Aspen

Treesearch

Harold A. Stewart

1971-01-01

Aspen at 6 percent moisture content was planed parallel to the grain and across the grain on a cabinet planer with a 25? rake angle, 1/16- and 1/32-inch depth of cut, and 20 knife marks per inch. Aspen was also cross-grain knife planed with a 45? rake angle, 1/32-, 1/16-, and 1/8-inch depths of cut, and 20, 10, 5, and 2.5 knife marks per inch. Cross-grain knife...
F-16XL ship #1 - CAWAP boundary layer rakes and hot film on left wing

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the boundary layer hot film and the boundary layer rakes on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.
Wall Boundary Layer Measurements for the NASA Langley Transonic Dynamics Tunnel

NASA Technical Reports Server (NTRS)

Wieseman, Carol D.; Bennett, Robert M.

2007-01-01

Measurements of the boundary layer parameters in the NASA Langley Transonic Dynamics tunnel were conducted during extensive calibration activities following the facility conversion from a Freon-12 heavy-gas test medium to R-134a. Boundary-layer rakes were mounted on the wind-tunnel walls, ceiling, and floor. Measurements were made over the range of tunnel operation envelope in both heavy gas and air and without a model in the test section at three tunnel stations. Configuration variables included open and closed east sidewall wall slots, for air and R134a test media, reentry flap settings, and stagnation pressures over the full range of tunnel operation. The boundary layer thickness varied considerably for the six rakes. The thickness for the east wall was considerably larger that the other rakes and was also larger than previously reported. There generally was some reduction in thickness at supersonic Mach numbers, but the effect of stagnation pressure, and test medium were not extensive.
Aerodynamic Analysis of Variable Geometry Raked Wingtips for Mid-Range Transonic Transport Aircraft

NASA Astrophysics Data System (ADS)

Jingeleski, David J.

Previous applications have shown that a wingtip treatment on a commercial airliner will reduce drag and increase fuel efficiency and the most common types of treatment are blended winglets and raked wingtips. With Boeing currently investigating novel designs for its next generation of airliners, a variable geometry raked wingtip novel control effector (VGRWT/NCE) was studied to determine the aerodynamic performance benefits over an untreated wingtip. The Boeing SUGAR design employing a truss-braced wing was selected as the baseline. Vortex lattice method (VLM) and computational fluid dynamics (CFD) software was implemented to analyze the aerodynamic performance of such a configuration applied to a next-generation, transonic, mid-range transport aircraft. Several models were created to simulate various sweep positions for the VGRWT/NCE tip, as well as a baseline model with an untreated wingtip. The majority of investigation was conducted using the VLM software, with CFD used largely as a validation of the VLM analysis. The VGRWT/NCE tip was shown to increase the lift of the wing while also decreasing the drag. As expected, the unswept VGRWT/NCE tip increases the amount of lift available over the untreated wingtip, which will be very beneficial for take-off and landing. Similarly, the swept VGRWT/NCE tip reduced the drag of the wing during cruise compared to the unmodified tip, which will favorably impact the fuel efficiency of the aircraft. Also, the swept VGRWT/NCE tip showed an increase in moment compared to the unmodified wingtip, implying an increase in stability, as well providing an avenue for roll control and gust alleviation for flexible wings. CFD analysis validated VLM as a useful low fidelity tool that yielded quite accurate results. The main results of this study are tabulated "deltas" in the forces and moments on the VGRWT/NCE tip as a function of sweep angle and aileron deflection compared to the baseline wing. A side study of the effects of the joint between the main wing and the movable tip showed that the drag impact can be kept small by careful design.

High-Subsonic Performance Characteristics and Boundary-Layer Investigations of a 12 deg 10-Inch-Inlet-Diameter Conical Diffuser

DTIC Science & Technology

1950-05-11

available condition supersonic flow was obtained as far as K.5 inches downstream from the diffueer inlet with a maximum Mach number of M % 1.5...Boundary—layer total-pressure measurements were made with the rake shown in figure k. The tubes varied in size from 0.030-Inch outside diameter...at the wall to 0.050—inch outside diameter farther out. A static-pressure tube was mounted on the rake to measure static pressures at the same
Experiments in Numerical Studies of Low Density and Real Gas Effects on Regions of Shock Wave/Boundary Layer Interaction in Hypervelocity Flows

DTIC Science & Technology

2006-06-01

Figure 13 Survey Rake containing Instrumentation to Measure Pitot and Static Pressure, Heating Distributions on Cylinders and Spheres, and Cone...35a and is in close agreement with the inviscid flow prediction in Figure 35b. Measurements made with a pitot pressure rake positioned at the end of...Velocity 15,00o 7 ’ DISOl• AglOrf (feet per sec) 10 N•’’ 10,000 47_T"___ ____ VIBATIONA Hypersonic 5,000 EXCITATION REGION Supersonic IDEAL GAS -Transonic 0
Fluid Dynamic and Acoustic Experiments on Turbomachine Rotors Subject to Variable Flow Conditions

DTIC Science & Technology

1990-03-31

conjunction with a standard pitot tube that is mounted in the wind tunnel test section upstream of the dynamometer system. The 4 manometer has a...generator." The smoke is then pumped into a "smoke rake ," in which it cools to ambient temperature and is directed the smoke into the inlet of the wind...34 and "smoke rake " are shown in Figures 5 and 6. A more complete explanation of the smoke generation process and apparatus is provided by Mueller (1983
An Innovative Flow-Measuring Device: Thermocouple Boundary Layer Rake

NASA Technical Reports Server (NTRS)

Hwang, Danny P.; Fralick, Gustave C.; Martin, Lisa C.; Wrbanek, John D.; Blaha, Charles A.

2001-01-01

An innovative flow-measuring device, a thermocouple boundary layer rake, was developed. The sensor detects the flow by using a thin-film thermocouple (TC) array to measure the temperature difference across a heater strip. The heater and TC arrays are microfabricated on a constant-thickness quartz strut with low heat conductivity. The device can measure the velocity profile well into the boundary layer, about 65 gm from the surface, which is almost four times closer to the surface than has been possible with the previously used total pressure tube.
Experimental and numerical investigations on the temperature distribution in PVD AlTiN coated and uncoated Al2O3/TiCN mixed ceramic cutting tools in hard turning of AISI 52100 steel

NASA Astrophysics Data System (ADS)

Sateesh Kumar, Ch; Patel, Saroj Kumar; Das, Anshuman

2018-03-01

Temperature generation in cutting tools is one of the major causes of tool failure especially during hard machining where machining forces are quite high resulting in elevated temperatures. Thus, the present work investigates the temperature generation during hard machining of AISI 52100 steel (62 HRC hardness) with uncoated and PVD AlTiN coated Al2O3/TiCN mixed ceramic cutting tools. The experiments were performed on a heavy duty lathe machine with both coated and uncoated cutting tools under dry cutting environment. The temperature of the cutting zone was measured using an infrared thermometer and a finite element model has been adopted to predict the temperature distribution in cutting tools during machining for comparative assessment with the measured temperature. The experimental and numerical results revealed a significant reduction of cutting zone temperature during machining with PVD AlTiN coated cutting tools when compared to uncoated cutting tools during each experimental run. The main reason for decrease in temperature for AlTiN coated tools is the lower coefficient of friction offered by the coating material which allows the free flow of the chips on the rake surface when compared with uncoated cutting tools. Further, the superior wear behaviour of AlTiN coating resulted in reduction of cutting temperature.
Coseismic temporal changes of slip direction: the effect of absolute stress on dynamic rupture

USGS Publications Warehouse

Guatteri, Mariagiovanna; Spudich, P.

1998-01-01

We investigate the dynamics of rupture at low-stress level. We show that one main difference between the dynamics of high- and low-stress events is the amount of coseismic temporal rake rotation occurring at given points on the fault. Curved striations on exposed fault surfaces and earthquake dislocation models derived from ground-motion inversion indicate that the slip direction may change with time at a point on the fault during dynamic rupture. We use a 3D boundary integral method to model temporal rake variations during dynamic rupture propagation assuming a slip-weakening friction law and isotropic friction. The points at which the slip rotates most are characterized by an initial shear stress direction substantially different from the average stress direction over the fault plane. We show that for a given value of stress drop, the level of initial shear stress (i.e., the fractional stress drop) determines the amount of rotation in slip direction. We infer that seismic events that show evidence of temporal rake rotations are characterized by a low initial shear-stress level with spatially variable direction on the fault (possibly due to changes in fault surface geometry) and an almost complete stress drop.Our models motivate a new interpretation of curved and cross-cutting striations and put new constraints on their analysis. The initial rake is in general collinear with the initial stress at the hypocentral zone, supporting the assumptions made in stress-tensor inversion from first-motion analysis. At other points on the fault, especially away from the hypocenter, the initial slip rake may not be collinear with the initial shear stress, contradicting a common assumption of structural geology. On the other hand, the later part of slip in our models is systematically more aligned with the average stress direction than the early slip. Our modeling suggests that the length of the straight part of curved striations is usually an upper bound of the slip-weakening distance if this parameter is uniform over the fault plane, and the direction of the late part of slip of curved striations should have more weight in the estimate of initial stress direction.
Energy Analysis of Decoders for Rakeness-Based Compressed Sensing of ECG Signals.

PubMed

Pareschi, Fabio; Mangia, Mauro; Bortolotti, Daniele; Bartolini, Andrea; Benini, Luca; Rovatti, Riccardo; Setti, Gianluca

2017-12-01

In recent years, compressed sensing (CS) has proved to be effective in lowering the power consumption of sensing nodes in biomedical signal processing devices. This is due to the fact the CS is capable of reducing the amount of data to be transmitted to ensure correct reconstruction of the acquired waveforms. Rakeness-based CS has been introduced to further reduce the amount of transmitted data by exploiting the uneven distribution to the sensed signal energy. Yet, so far no thorough analysis exists on the impact of its adoption on CS decoder performance. The latter point is of great importance, since body-area sensor network architectures may include intermediate gateway nodes that receive and reconstruct signals to provide local services before relaying data to a remote server. In this paper, we fill this gap by showing that rakeness-based design also improves reconstruction performance. We quantify these findings in the case of ECG signals and when a variety of reconstruction algorithms are used either in a low-power microcontroller or a heterogeneous mobile computing platform.
Ductile cutting of silicon microstructures with surface inclination measurement and compensation by using a force sensor integrated single point diamond tool

NASA Astrophysics Data System (ADS)

Chen, Yuan-Liu; Cai, Yindi; Shimizu, Yuki; Ito, So; Gao, Wei; Ju, Bing-Feng

2016-02-01

This paper presents a measurement and compensation method of surface inclination for ductile cutting of silicon microstructures by using a diamond tool with a force sensor based on a four-axis ultra-precision lathe. The X- and Y-directional inclinations of a single crystal silicon workpiece with respect to the X- and Y-motion axes of the lathe slides were measured respectively by employing the diamond tool as a touch-trigger probe, in which the tool-workpiece contact is sensitively detected by monitoring the force sensor output. Based on the measurement results, fabrication of silicon microstructures can be thus carried out directly along the tilted silicon workpiece by compensating the cutting motion axis to be parallel to the silicon surface without time-consuming pre-adjustment of the surface inclination or turning of a flat surface. A diamond tool with a negative rake angle was used in the experiment for superior ductile cutting performance. The measurement precision by using the diamond tool as a touch-trigger probe was investigated. Experiments of surface inclination measurement and ultra-precision ductile cutting of a micro-pillar array and a micro-pyramid array with inclination compensation were carried out respectively to demonstrate the feasibility of the proposed method.
Tools being considered for use in freeing solar array wing of Skylab

NASA Image and Video Library

1973-06-05

S73-27403 (June 1973) --- Engineers at the NASA Marshall Space Flight Center examine tools that are being considered for use in freeing the solar array wing of Skylab. The device at center is a cable cutter which is operated by cable. Enhanced television pictures indicate that the wing is being held to the side of the Skylab by a strip of metal from the meteoroid shield. The cable cutter shown here clipped an identical strip of metal in a test at the Marshall Center, requiring 90 pounds of force. The cutter is one of several heads which could be attached to extension rods. Identical tools and rods were carried into orbit by the Skylab 2 crew. At right is the handle end of a rod. White material taped just below the handle is buoyancy packing to make the object weightless when submerged in water. The tools are being tested in underwater EVA tasks in the MSFC Neutral Buoyancy Simulator. Small object at left is the attachment head for a two-prong "rake" device for use on the end of a pole made up of one, two or more five-foot sections of extension rods. Photo credit: NASA
Tools and technologies needed for conducting planetary field geology while on EVA: Insights from the 2010 Desert RATS geologist crewmembers

NASA Astrophysics Data System (ADS)

Young, Kelsey; Hurtado, José M.; Bleacher, Jacob E.; Brent Garry, W.; Bleisath, Scott; Buffington, Jesse; Rice, James W.

2013-10-01

The tools used by crews while on extravehicular activity during future missions to other bodies in the Solar System will be a combination of traditional geologic field tools (e.g. hammers, rakes, sample bags) and state-of-the-art technologies (e.g. high definition cameras, digital situational awareness devices, and new geologic tools). In the 2010 Desert Research and Technology Studies (RATS) field test, four crews, each consisting of an astronaut/engineer and field geologist, tested and evaluated various technologies during two weeks of simulated spacewalks in the San Francisco volcanic field, Arizona. These tools consisted of both Apollo-style field geology tools and modern technological equipment not used during the six Apollo lunar landings. The underlying exploration driver for this field test was to establish the protocols and technology needed for an eventual manned mission to an asteroid, the Moon, or Mars. The authors of this paper represent Desert RATS geologist crewmembers as well as two engineers who worked on technology development. Here we present an evaluation and assessment of these tools and technologies based on our first-hand experience of using them during the analog field test. We intend this to serve as a basis for continued development of technologies and protocols used for conducting planetary field geology as the Solar System exploration community moves forward into the next generation of planetary surface exploration.
Calculation of sidewall boundary-layer parameters from rake measurements for the Langley 0.3-meter transonic cryogenic tunnel

NASA Technical Reports Server (NTRS)

Murthy, A. V.

1987-01-01

Correction of airfoil data for sidewall boundary-layer effects requires a knowledge of the boundary-layer displacement thickness and the shape factor with the tunnel empty. To facilitate calculation of these quantities under various test conditions for the Langley 0.3 m Transonic Cryogenic Tunnel, a computer program was written. This program reads the various tunnel parameters and the boundary-layer rake total head pressure measurements directly from the Engineering Unit tapes to calculate the required sidewall boundary-layer parameters. Details of the method along with the results for a sample case are presented.
Experimental and predicted pressure and heating distributions for an Aeroassist Flight Experiment vehicle in air at Mach 10

NASA Technical Reports Server (NTRS)

Micol, John R.

1989-01-01

The Aeroassisted Flight Experiment vehicle for whose scale model pressure and heat-transfer rate distributions have been measured in air at Mach 10 is a 60-deg elliptic cone, raked off at a 73-percent angle, with an ellipsoid nose and a skirt added to the base of the rake plane to reduce heating. The predictions of both an inviscid flow-field code and a Navier-Stokes solver are compared with measured values. Good agreement is obtained in the case of pressure distributions; the effect of Reynolds number on heat-transfer distributions is noted to be small.
Duct Mode Measurements on the TFE731-60 Full Scale Engine

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.; Konno, Kevin E.; Heidelberg, Laurence J.

2002-01-01

A continuously rotating rake with radial microphones was developed to measure the inlet and exhaust duct modes on a TFE731-60 turbofan engine. This was the first time the rotating rake technology was used on a production engine. The modal signature for the first three fan harmonics was obtained in the inlet and exhaust. Rotor-stator and rotor-strut interaction modes were measured. Total harmonic power was calculated over a range of fan speeds. Above sonic tip speed, the rotor locked mode was not strong enough to be identified, but the 'buzz-saw' noise at fan sub-harmonics was identified.
Flowfield measurements in the NASA Lewis Research Center 9- by 15-foot low-speed wind tunnel

NASA Technical Reports Server (NTRS)

Hughes, Christopher E.

1989-01-01

An experimental investigation was conducted in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel to determine the flow characteristics in the test section during wind tunnel operation. In the investigation, a 20-probe horizontally-mounted Pitot-static flow survey rake was used to obtain cross-sectional total and static pressure surveys at four axial locations in the test section. At each axial location, the cross-sectional flowfield surveys were made by repositioning the Pitot-static flow survey rake vertically. In addition, a calibration of the new wind tunnel rake instrumentation, used to determine the wind tunnel operating conditions, was performed. Boundary laser surveys were made at three axial locations in the test section. The investigation was conducted at tunnel Mach numbers 0.20, 0.15, 0.10, and 0.05. The test section profile results from the investigation indicate that fairly uniform total pressure profiles (outside the test section boundary layer) and fairly uniform static pressure and Mach number profiles (away from the test section walls and downstream of the test section entrance) exist throughout in the wind tunnel test section.
Wireless rake-receiver using adaptive filter with a family of partial update algorithms in noise cancellation applications

NASA Astrophysics Data System (ADS)

Fayadh, Rashid A.; Malek, F.; Fadhil, Hilal A.; Aldhaibani, Jaafar A.; Salman, M. K.; Abdullah, Farah Salwani

2015-05-01

For high data rate propagation in wireless ultra-wideband (UWB) communication systems, the inter-symbol interference (ISI), multiple-access interference (MAI), and multiple-users interference (MUI) are influencing the performance of the wireless systems. In this paper, the rake-receiver was presented with the spread signal by direct sequence spread spectrum (DS-SS) technique. The adaptive rake-receiver structure was shown with adjusting the receiver tap weights using least mean squares (LMS), normalized least mean squares (NLMS), and affine projection algorithms (APA) to support the weak signals by noise cancellation and mitigate the interferences. To minimize the data convergence speed and to reduce the computational complexity by the previous algorithms, a well-known approach of partial-updates (PU) adaptive filters were employed with algorithms, such as sequential-partial, periodic-partial, M-max-partial, and selective-partial updates (SPU) in the proposed system. The simulation results of bit error rate (BER) versus signal-to-noise ratio (SNR) are illustrated to show the performance of partial-update algorithms that have nearly comparable performance with the full update adaptive filters. Furthermore, the SPU-partial has closed performance to the full-NLMS and full-APA while the M-max-partial has closed performance to the full-LMS updates algorithms.
Flight-measured pressure characteristics of aft-facing steps in high Reynolds number flow at Mach numbers of 2.20, 2.50, and 2.80 and comparison with other data

NASA Technical Reports Server (NTRS)

Powers, S. G.

1978-01-01

The YF-12 airplane was studied to determine the pressure characteristics associated with an aft-facing step in high Reynolds number flow for nominal Mach numbers of 2.20, 2.50, and 2.80. Base pressure coefficients were obtained for three step heights. The surface static pressures ahead of and behind the step were measured for the no-step condition and for each of the step heights. A boundary layer rake was used to determine the local boundary layer conditions. The Reynolds number based on the length of flow ahead of the step was approximately 10 to the 8th power and the ratios of momentum thickness to step height ranged from 0.2 to 1.0. Base pressure coefficients were compared with other available data at similar Mach numbers and at ratios of momentum thickness to step height near 1.0. In addition, the data were compared with base pressure coefficients calculated by a semiempirical prediction method. The base pressure ratios are shown to be a function of Reynolds number based on momentum thickness. Profiles of the surface pressures ahead of and behind the step and the local boundary layer conditions are also presented.
Performance of Ultra Wideband On-Body Communication Based on Statistical Channel Model

NASA Astrophysics Data System (ADS)

Wang, Qiong; Wang, Jianqing

Ultra wideband (UWB) on-body communication is attracting much attention in biomedical applications. In this paper, the performance of UWB on-body communication is investigated based on a statistically extracted on-body channel model, which provides detailed characteristics of the multi-path-affected channel with an emphasis on various body postures or body movement. The possible data rate, the possible communication distance, as well as the bit error rate (BER) performance are clarified via computer simulation. It is found that the conventional correlation receiver is incompetent in the multi-path-affected on-body channel, while the RAKE receiver outperforms the conventional correlation receiver at a cost of structure complexity. Different RAKE receiver structures are compared to show the improvement of the BER performance.
Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation

PubMed Central

Gharwade, Chandrakant Rambhau

2016-01-01

Follicular unit extraction (FUE) is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant). Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs). The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°–15°) of emergent hair from scalp skin, higher variance angle (15°–35°) between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions. PMID:28216821
Enhancement of fine-scale mixing for fuel-rich plume combustion

NASA Astrophysics Data System (ADS)

Schadow, K. C.; Gutmark, E.; Parr, T. P.; Parr, D. M.; Wilson, K. J.; Ferrell, G. B.

1987-01-01

The effect of enhancing small-scale turbulent structures on the combustion intensity and flame stability was studied in nonreacting and reacting flows. Hot-wire anemometry was used to map the mean and turbulent flow fields of the nonreacting flows. Reacting flows were studied in a free flame and in a ducted gas-generator fuel-rich plume using Planar Laser Induced Fluorescence, a rake of thermocouples and high speed photography. A modified circular nozzle having several backward facing steps upstream of its exit was used to introduce numerous inflection points in the initial mean velocity profiles, thus producing multiple corresponding sources of small-scale turbulence generators. Cold flow tests showed turbulence increases of up to six times the initial turbulence level relative to a circular nozzle. The ensuing result was that the flame of this nozzle was more intense with a homogeneous heat release. The fuel-rich plume was stable even in supersonic speeds, and secondary ignition was obtained under conditions that prevented sustained afterburning using the circular nozzle.
Functional morphology and biomechanics of the tongue-bite apparatus in salmonid and osteoglossomorph fishes

PubMed Central

Camp, Ariel L; Konow, Nicolai; Sanford, Christopher P J

2009-01-01

The tongue-bite apparatus and its associated musculoskeletal elements of the pectoral girdle and neurocranium form the structural basis of raking, a unique prey-processing behaviour in salmonid and osteoglossomorph fishes. Using a quantitative approach, the functional osteology and myology of this system were compared between representatives of each lineage, i.e. the salmonid Salvelinus fontinalis (N =10) and the osteoglossomorph Chitala ornata(N = 8). Divergence was found in the morphology of the novel cleithrobranchial ligament, which potentially relates to kinematic differences between the raking lineage representatives. Salvelinus had greater anatomical cross-sectional areas of the epaxial, hypaxial and protractor hyoideus muscles, whereas Chitala had greater sternohyoideus and adductor mandibulae mass. Two osteology-based biomechanical models (a third-order lever for neurocranial elevation and a modified four-bar linkage for hyoid retraction) showed divergent force/velocity priorities in the study taxa. Salvelinus maximizes both force (via powerful cranial muscles) and velocity (through mechanical amplification) during raking. In contrast, Chitala has relatively low muscle force but more efficient force transmission through both mechanisms compared with Salvelinus. It remains unclear if and how behavioural modulation and specializations in the post-cranial anatomy may affect the force/velocity trade-offs in Chitala. Further studies of tongue-bite apparatus morphology and biomechanics in a broader species range may help to clarify the role that osteology and myology play in the evolution of behavioural diversity. PMID:19438765

Integrated CFD modeling of gas turbine combustors

NASA Technical Reports Server (NTRS)

Fuller, E. J.; Smith, C. E.

1993-01-01

3D, curvilinear, multi-domain CFD analysis is becoming a valuable tool in gas turbine combustor design. Used as a supplement to experimental testing. CFD analysis can provide improved understanding of combustor aerodynamics and used to qualitatively assess new combustor designs. This paper discusses recent advancements in CFD combustor methodology, including the timely integration of the design (i.e. CAD) and analysis (i.e. CFD) processes. Allied Signal's F124 combustor was analyzed at maximum power conditions. The assumption of turbulence levels at the nozzle/swirler inlet was shown to be very important in the prediction of combustor exit temperatures. Predicted exit temperatures were compared to experimental rake data, and good overall agreement was seen. Exit radial temperature profiles were well predicted, while the predicted pattern factor was 25 percent higher than the harmonic-averaged experimental pattern factor.
Golfer's Elbow

MedlinePlus

... your elbow can cause golfer's elbow. This includes painting, raking, hammering, chopping wood, using a computer, doing ... using older golfing irons, consider upgrading to lighter graphite clubs. If you play tennis, a racket with ...
Comparison of Direct Sequence Spread Spectrum Rake Receiver with a Maximum Ratio Combining Multicarrier Spread Spectrum Receiver

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daryl Leon Wasden; Hussein Moradi; Behrouz Farhang-Broujeny

2014-06-01

This paper presents a theoretical analysis of the performance of a filter bank-based multicarrier spread spectrum (FB-MC-SS) system. We consider an FB-MC-SS setup where each data symbol is spread across multiple subcarriers, but there is no spreading in time. The results are then compared with those of the well-known direct sequence spread spectrum (DS-SS) system with a rake receiver for its best performance. We compare the two systems when the channel noise is white. We prove that as the processing gains of the two systems tend to infinity both approach the same performance. However, numerical simulations show that, in practice,more » where processing gain is limited, FB-MC-SS outperforms DS-SS.« less
Slip re-orientation in the oblique Abiquiu embayment, northern Rio Grande rift

NASA Astrophysics Data System (ADS)

Liu, Y.; Murphy, M. A.; Andrea, R. A.

2015-12-01

Traditional models of oblique rifting predict that an oblique fault accommodates both dip-slip and strike-slip kinematics. However, recent analog experiments suggest that slip can be re-oriented to almost pure dip-slip on oblique faults if a preexisting weak zone is present at the onset of oblique extension. In this study, we use fault slip data from the Abiquiu embayment in northern Rio Grande rift to test the new model. The Rio Grande rift is a Cenozoic oblique rift extending from southern Colorado to New Mexico. From north to south, it comprises three major half grabens (San Luis, Española, and Albuquerque). The Abiquiu embayment is a sub-basin of the San Luis basin in northern New Mexico. Rift-border faults are generally older and oblique to the trend of the rift, whereas internal faults are younger and approximately N-S striking, i.e. orthogonal to the regional extension direction. Rift-border faults are deep-seated in the basement rocks while the internal faults only cut shallow stratigraphic sections. It has been suggested by many that inherited structures may influence the Rio Grande rifting. Particularly, Laramide structures (and possibly the Ancestral Rockies as well) that bound the Abiquiu embayment strike N- to NW. Our data show that internal faults in the Abiquiu embayment exhibit almost pure dip-slip (rake of slickenlines = 90º ± 15º), independent of their orientations with respect to the regional extension direction. On the contrary, border faults show two sets of rakes: almost pure dip-slip (rake = 90º ± 15º) where the fault is sub-parallel to the foliation, and moderately-oblique (rake = 30º ± 15º) where the fault is high angle to the foliation. We conclude that slip re-orientation occurs on most internal faults and some oblique border faults under the influence of inherited structures. Regarding those border faults on which slip is not re-oriented, we hypothesize that it may be caused by the Jemez volcanism or small-scale mantle convection.
Bonnie Takes Aim at an Oily Gulf

NASA Image and Video Library

2010-07-24

Tropical Storm Bonnie, now a depression, rakes South Florida in this infrared image from NASA Atmospheric Infrared Sounder , en route to a weekend run-in with the Gulf of Mexico and the Gulf oil spill.
In-flight comparisons of boundary-layer and wake measurement probes for incompressible flow

NASA Technical Reports Server (NTRS)

Mertaugh, L. J., Jr.

1972-01-01

The results are presented of in-flight comparisons of a number of boundary-layer and wake measurement probes suitable for low-speed flight-test investigations. The tested boundary-layer probes included a traversing total-pressure probe and a hot-film probe mounted on an internally-mounted drive mechanism, a curved and a straight boundary-layer rake, and a traversing hot-film probe with an externally-mounted drive mechanism. The wake measuring devices included a traversing, self-aligning probe, a wake rake, and an integrating wake rate. The boundary-layer data are compared with a common reference velocity profile and comments given regarding the accuracy of the static-pressure and total-pressure measurements. Discussions on the various calibration presentations used with hot-wire and hot-film sensors and various aspects of improving the accuracy of hot-film sensor results are given in the appendix of this report.
Probabilistic Analysis and Design of a Raked Wing Tip for a Commercial Transport

NASA Technical Reports Server (NTRS)

Mason Brian H.; Chen, Tzi-Kang; Padula, Sharon L.; Ransom, Jonathan B.; Stroud, W. Jefferson

2008-01-01

An approach for conducting reliability-based design and optimization (RBDO) of a Boeing 767 raked wing tip (RWT) is presented. The goal is to evaluate the benefits of RBDO for design of an aircraft substructure. A finite-element (FE) model that includes eight critical static load cases is used to evaluate the response of the wing tip. Thirteen design variables that describe the thickness of the composite skins and stiffeners are selected to minimize the weight of the wing tip. A strain-based margin of safety is used to evaluate the performance of the structure. The randomness in the load scale factor and in the strain limits is considered. Of the 13 variables, the wing-tip design was controlled primarily by the thickness of the thickest plies in the upper skins. The report includes an analysis of the optimization results and recommendations for future reliability-based studies.
Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake

NASA Astrophysics Data System (ADS)

Heidelberg, Laurence J.; Hall, David G.

1993-01-01

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.
Acoustic Mode Measurements in the Inlet of a Model Turbofan Using a Continuously Rotating Rake

NASA Technical Reports Server (NTRS)

Heidelberg, Laurence J.; Hall, David G.

1992-01-01

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.
Test data from small solid propellant rocket motor plume measurements (FA-21)

NASA Technical Reports Server (NTRS)

Hair, L. M.; Somers, R. E.

1976-01-01

A program is described for obtaining a reliable, parametric set of measurements in the exhaust plumes of solid propellant rocket motors. Plume measurements included pressures, temperatures, forces, heat transfer rates, particle sampling, and high-speed movies. Approximately 210,000 digital data points and 15,000 movie frames were acquired. Measurements were made at points in the plumes via rake-mounted probes, and on the surface of a large plate impinged by the exhaust plume. Parametric variations were made in pressure altitude, propellant aluminum loading, impinged plate incidence angle and distance from nozzle exit to plate or rake. Reliability was incorporated by continual use of repeat runs. The test setup of the various hardware items is described along with an account of test procedures. Test results and data accuracy are discussed. Format of the data presentation is detailed. Complete data are included in the appendix.
Integrating Cloud-Based Strategies and Tools in Face-to-Face Training Sessions to Increase the Impact of Professional Development

ERIC Educational Resources Information Center

Gradel, Kathleen; Edson, Alden J.

2012-01-01

This article is based on the premise that face-to-face training can be augmented with cloud-based technology tools, to potentially extend viable training supports as higher education staff and faculty implement new content/skills in their jobs and classrooms. There are significant benefits to harnessing cloud-based tools that can facilitate both…
Impact of Collection Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

DOE Office of Scientific and Technical Information (OSTI.GOV)

William Smith; Jeffery Einerson; Kevin Kenney

2014-09-01

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment testedmore » included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg-1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.« less
Promoting species establishment in a phragmites-dominated great lakes coastal wetland

USGS Publications Warehouse

Carlson, M.L.; Kowalski, K.P.; Wilcox, D.A.

2009-01-01

This study examined efforts to promote species establishment and maintain diversity in a Phragmites-dominated wetland where primary control measures were underway. A treatment experiment was performed at Crane Creek, a drowned-river-mouth wetland in Ottawa National Wildlife Refuge along the shore of western Lake Erie. Following initial aerial spraying of Phragmites with glyphosate, this study tested combinations of cutting, raking, and additional hand spraying of Phragmites with glyphosate as methods to promote growth of other wetland species and increase plant diversity. Percent-cover vegetation data were collected in permanent plots before and after treatments, and follow-up sampling was performed the following year. Increased species richness, species emergence, and relative dominance of non-Phragmites taxa were used as measures of treatment success. We also examined treatment effects on Phragmites cover. Dimensionality of seedbank and soil properties was reduced using principal component analysis. With the exception of nitrogen, soil nutrients affected species establishment, non-Phragmites taxa dominance, and Phragmites cover. A more viable seedbank led to greater species emergence. Treatments had differential effects on diversity depending on elevation and resulting degree of hydrologic inundation. Whereas raking to remove dead Phragmites biomass was central to promoting species establishment in dry areas, spraying had a greater impact in continually inundated areas. For treatment success across elevations into the year following treatments, spraying in combination with cutting and raking had the greatest effect. The results of this study suggest that secondary treatments can produce a short-term benefit to the plant community in areas treated for Phragmites.
CAE Based Die Face Engineering Development to Contribute to the Revitalization of the Tool & Die Industry

NASA Astrophysics Data System (ADS)

Tang, Arthur; Lee, Wing C.; St. Pierre, Shawn; He, Jeanne; Liu, Kesu; Chen, Chin C.

2005-08-01

Over the past two decades, the Computer Aided Engineering (CAE) tools have emerged as one of the most important engineering tools in various industries, due to its flexibility and accuracy in prediction. Nowadays, CAE tools are widely used in the sheet metal forming industry to predict the forming feasibility of a wide variety of complex components, ranging from aerospace and automotive components to household products. As the demand of CAE based formability accelerates, the need for a robust and streamlined die face engineering tool becomes more crucial, especially in the early stage when the tooling layout is not available, but a product design decision must be made. Ability to generate blank, binder and addendum surfaces with an appropriate layout of Drawbead, Punch Opening Line, Trim Line are the primary features and functions of a CAE based die face engineering tool. Once the die face layout is ready, a formability study should be followed to verify the die face layout is adequate to produce a formable part. If successful, the established die face surface should be exported back to the CAD/CAM environment to speed up the tooling and manufacturing design process with confidence that this particular part is formable with this given die face. With a CAE tool as described above, the tool & die industry will be greatly impacted as the processes will enable the bypass of hardware try-out and shorten the overall vehicle production timing. The trend has shown that OEMs and first tiers will source to low cost producers in the world which will have a negative impact to the traditional tool & die makers in the developed countries. CAE based tool as described should be adopted, along with many other solutions, in order to maintain efficiency of producing high quality product and meeting time-to-market requirements. This paper will describe how a CAE based die face engineering (DFE) tool could be further developed to enable the traditional tool & die makers to meet the challenge ahead.
Reliability-Based Design Optimization of a Composite Airframe Component

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Coroneos, Rula M.

2009-01-01

A stochastic design optimization methodology (SDO) has been developed to design components of an airframe structure that can be made of metallic and composite materials. The design is obtained as a function of the risk level, or reliability, p. The design method treats uncertainties in load, strength, and material properties as distribution functions, which are defined with mean values and standard deviations. A design constraint or a failure mode is specified as a function of reliability p. Solution to stochastic optimization yields the weight of a structure as a function of reliability p. Optimum weight versus reliability p traced out an inverted-S-shaped graph. The center of the inverted-S graph corresponded to 50 percent (p = 0.5) probability of success. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure that corresponds to unity for reliability p (or p = 1). Weight can be reduced to a small value for the most failure-prone design with a reliability that approaches zero (p = 0). Reliability can be changed for different components of an airframe structure. For example, the landing gear can be designed for a very high reliability, whereas it can be reduced to a small extent for a raked wingtip. The SDO capability is obtained by combining three codes: (1) The MSC/Nastran code was the deterministic analysis tool, (2) The fast probabilistic integrator, or the FPI module of the NESSUS software, was the probabilistic calculator, and (3) NASA Glenn Research Center s optimization testbed CometBoards became the optimizer. The SDO capability requires a finite element structural model, a material model, a load model, and a design model. The stochastic optimization concept is illustrated considering an academic example and a real-life raked wingtip structure of the Boeing 767-400 extended range airliner made of metallic and composite materials.
Portable Roller Staking Tool

NASA Technical Reports Server (NTRS)

Bird, R. G.; Berson, L. A.

1983-01-01

Staking tool compact and portable. Tool combines clamping and staking operations in single unit. Tool clamps workpiece (a bearing or bushing), alines it, and stakes on of flat faces. Used for most roller staking operations which acess both faces of workpiece.
Crashworthiness analysis of the January 26, 2005 Glendale, California rail collision

DOT National Transportation Integrated Search

2011-03-16

In Glendale, California on January 26, 2005, impact with : an SUV on the track caused a southbound commuter train to : derail, impact a standing freight train, buckle laterally outward, : and rake the side of a northbound commuter train. Significant ...
Effects of fault dip and slip rake angles on near-source ground motions: Why rupture directivity was minimal in the 1999 Chi-Chi, Taiwan, earthquake

USGS Publications Warehouse

Aagaard, Brad T.; Hall, J.F.; Heaton, T.H.

2004-01-01

We study how the fault dip and slip rake angles affect near-source ground velocities and displacements as faulting transitions from strike-slip motion on a vertical fault to thrust motion on a shallow-dipping fault. Ground motions are computed for five fault geometries with different combinations of fault dip and rake angles and common values for the fault area and the average slip. The nature of the shear-wave directivity is the key factor in determining the size and distribution of the peak velocities and displacements. Strong shear-wave directivity requires that (1) the observer is located in the direction of rupture propagation and (2) the rupture propagates parallel to the direction of the fault slip vector. We show that predominantly along-strike rupture of a thrust fault (geometry similar in the Chi-Chi earthquake) minimizes the area subjected to large-amplitude velocity pulses associated with rupture directivity, because the rupture propagates perpendicular to the slip vector; that is, the rupture propagates in the direction of a node in the shear-wave radiation pattern. In our simulations with a shallow hypocenter, the maximum peak-to-peak horizontal velocities exceed 1.5 m/sec over an area of only 200 km2 for the 30??-dipping fault (geometry similar to the Chi-Chi earthquake), whereas for the 60??- and 75??-dipping faults this velocity is exceeded over an area of 2700 km2 . These simulations indicate that the area subjected to large-amplitude long-period ground motions would be larger for events of the same size as Chi-Chi that have different styles of faulting or a deeper hypocenter.
Sugarcane cultural practices to increase profits

USDA-ARS?s Scientific Manuscript database

Multiple experiments were initiated in an effort to reduce costs, increase ratooning, and maximize profits. A new method of mechanical removal using a modified rake produced yields similarly to burning, with both yielding an additional 1000 lbs/A than full retention. Where burning was not an option,...
Big Jobs: Planning for Competence

ERIC Educational Resources Information Center

Jones, Nancy P.

2005-01-01

Three- to five-year-olds grow emotionally participating in meaningful and challenging physical, social, and problem-solving activities outdoors in an early childhood program on a farm. Caring for animals, planting, raking, shoveling, and engaging in meaningful indoor activities, under adult supervision, children learn to work collaboratively,…

Investigating the effects of PDC cutters geometry on ROP using the Taguchi technique

NASA Astrophysics Data System (ADS)

Jamaludin, A. A.; Mehat, N. M.; Kamaruddin, S.

2017-10-01

At times, the polycrystalline diamond compact (PDC) bit’s performance dropped and affects the rate of penetration (ROP). The objective of this project is to investigate the effect of PDC cutter geometry and optimize them. An intensive study in cutter geometry would further enhance the ROP performance. The relatively extended analysis was carried out and four significant geometry factors have been identified that directly improved the ROP. Cutter size, back rake angle, side rake angle and chamfer angle are the stated geometry factors. An appropriate optimization technique that effectively controls all influential geometry factors during cutters manufacturing is introduced and adopted in this project. By adopting L9 Taguchi OA, simulation experiment is conducted by using explicit dynamics finite element analysis. Through a structure Taguchi analysis, ANOVA confirms that the most significant geometry to improve ROP is cutter size (99.16% percentage contribution). The optimized cutter is expected to drill with high ROP that can reduce the rig time, which in its turn, may reduce the total drilling cost.
The effects of floor incline on lower extremity biomechanics during unilateral landing from a jump in dancers.

PubMed

Pappas, Evangelos; Orishimo, Karl F; Kremenic, Ian; Liederbach, Marijeanne; Hagins, Marshall

2012-05-01

Retrospective studies have suggested that dancers performing on inclined ("raked") stages have increased injury risk. One study suggests that biomechanical differences exist between flat and inclined surfaces during bilateral landings; however, no studies have examined whether such differences exist during unilateral landings. In addition, little is known regarding potential gender differences in landing mechanics of dancers. Professional dancers (N = 41; 14 male, 27 female) performed unilateral drop jumps from a 30 cm platform onto flat and inclined surfaces while extremity joint angles and moments were identified and analyzed. There were significant joint angle and moment effects due to the inclined flooring. Women had significantly decreased peak ankle dorsiflexion and hip adduction moment compared with men. Findings of the current study suggest that unilateral landings on inclined stages create measurable changes in lower extremity biomechanical variables. These findings provide a preliminary biomechanical rationale for differences in injury rates found in observational studies of raked stages.
Effects of Distortion on Mass Flow Plug Calibration

NASA Technical Reports Server (NTRS)

Sasson, Jonathan; Davis, David O.; Barnhart, Paul J.

2015-01-01

A numerical, and experimental investigation to study the effects of flow distortion on a Mass Flow Plug (MFP) used to control and measure mass-flow during an inlet test has been conducted. The MFP was first calibrated using the WIND-US flow solver for uniform (undistorted) inflow conditions. These results are shown to compare favorably with an experimental calibration under similar conditions. The effects of distortion were investigated by imposing distorted flow conditions taken from an actual inlet test to the inflow plane of the numerical simulation. The computational fluid dynamic (CFD) based distortion study only showed the general trend in mass flow rate. The study used only total pressure as the upstream boundary condition, which was not enough to define the flow. A better simulation requires knowledge of the turbulence structure and a specific distortion pattern over a range of plug positions. It is recommended that future distortion studies utilize a rake with at least the same amount of pitot tubes as the AIP rake.
The generation of tire cornering forces in aircraft with a free-swiveling nose gear

NASA Technical Reports Server (NTRS)

Daugherty, R. H.; Stubbs, S. M.

1985-01-01

An experimental investigation was conducted to study the effect of various parameters on the cornering forces produced by a rolling aircraft tire installed on a tilted, free-swiveling nose gear. The parameters studied included tilt angle, trial, tire inflation pressure, rake angle, vertical load, and whether or not a twin tire configuration corotates. These parameters were evaluated by measuring the cornering force produced by an aircraft tire installed on the nose gear of a modified vehicle as it was towed slowly. Cornering force coefficient increased with increasing tilt angle. Increasing trial or rake angle decreased the magnitude of the cornering force coefficient. Tire inflation pressure had no effect on the cornering force coefficient. Increasing vertical load decreased the cornering force coefficient. When the tires of a twin tire system rotated independently, the cornering force coefficients were the same as those for the single-tire configuration. When the twin tire system was made to corotate, however, the cornering force coefficients increased significantly.
16-foot transonic tunnel test section flowfield survey

NASA Technical Reports Server (NTRS)

Yetter, J. A.; Abeyounis, W. K.

1994-01-01

A flow survey has been made of the test section of the NASA Langley Research Center 16-Foot Transonic Tunnel at subsonic and supersonic speeds. The survey was performed using five five-hole pyramid-head probes mounted at 14 inch intervals on a survey rake. Probes were calibrated at freestream Mach numbers from 0.50 to 0.95 and from 1.18 to 1.23. Flowfield surveys were made at Mach numbers from 0.50 to 0.90 and at Mach 1.20. The surveys were made at tunnel stations 130.6, 133.6, and 136.0. By rotating the survey rake through 180 degrees, a cylindrical volume of the test section 4.7 feet in diameter and 5.4 feet long centered about the tunnel centerline was surveyed. Survey results showing the measured test section upflow and sideflow characteristics and local Mach number distributions are presented. The report documents the survey probe calibration techniques used, summarizes the procedural problems encountered during testing, and identifies the data discrepancies observed during the post-test data analysis.
Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake: Data collection/analysis techniques

NASA Technical Reports Server (NTRS)

Hall, David G.; Heidelberg, Laurence; Konno, Kevin

1993-01-01

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.
Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake - Data collection/analysis techniques

NASA Technical Reports Server (NTRS)

Hall, David G.; Heidelberg, Laurence; Konno, Kevin

1993-01-01

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.
Coulomb stress analysis of the 21 February 2008 Mw= 6.0 Wells, Nevada, earthquake

USGS Publications Warehouse

Sevilgen, Volkan

2011-01-01

Static Coulomb stress changes imparted by the February 21, 2008 Wells, Nevada earthquake are calculated, using an 8 x 6 km rectangular patch with a uniform slip as a source fault. Stress changes are resolved on nearby active faults using their rake, dip, and strike direction, assuming a fault friction of 0.4. The largest Coulomb stress increase (0.2 bars) imparted to surrounding major active faults from the Wells earthquake occurs on the Clover Hill fault, which may be the southern continuation of the ruptured fault. A 0.1 bar Coulomb stress increase is calculated on the western Snake Mountains fault. Coulomb stress decreases of 0.5 bars are calculated for the northern parts of the Independence and Ruby Mountains faults. The Coulomb stress change is calculated on relocated aftershocks assuming that they have the same strike, dip, and rake, as the source fault. Under this assumption, 75% of the aftershocks received a Coulomb stress increase.
Moment-tensor solutions for the 24 November 1987 Superstition Hills, California, earthquakes

USGS Publications Warehouse

Sipkin, S.A.

1989-01-01

The teleseismic long-period waveforms recorded by the Global Digital Seismograph Network from the two largest Superstition Hills earthquakes are inverted using an algorithm based on optimal filter theory. These solutions differ slightly from those published in the Preliminary Determination of Epicenters Monthly Listing because a somewhat different, improved data set was used in the inversions and a time-dependent moment-tensor algorithm was used to investigate the complexity of the main shock. The foreshock (origin time 01:54:14.5, mb 5.7, Ms6.2) had a scalar moment of 2.3 ?? 1025 dyne-cm, a depth of 8km, and a mechanism of strike 217??, dip 79??, rake 4??. The main shock (origin time 13:15:56.4, mb 6.0, Ms6.6) was a complex event, consisting of at least two subevents, with a combined scalar moment of 1.0 ?? 1026 dyne-cm, a depth of 10km, and a mechanism of strike 303??, dip 89??, rake -180??. -Authors
Aerodynamic Comparison of Hyper-Elliptic Cambered Span (HECS) Wings with Conventional Configurations

NASA Technical Reports Server (NTRS)

Lazos, Barry S.; Visser, Kenneth D.

2006-01-01

An experimental study was conducted to examine the aerodynamic and flow field characteristics of hyper-elliptic cambered span (HECS) wings and compare results with more conventional configurations used for induced drag reduction. Previous preliminary studies, indicating improved L/D characteristics when compared to an elliptical planform prompted this more detailed experimental investigation. Balance data were acquired on a series of swept and un-swept HECS wings, a baseline elliptic planform, two winglet designs and a raked tip configuration. Seven-hole probe wake surveys were also conducted downstream of a number of the configurations. Wind tunnel results indicated aerodynamic performance levels of all but one of the HECS wings exceeded that of the other configurations. The flow field data surveys indicate the HECS configurations displaced the tip vortex farther outboard of the wing than the Baseline configuration. Minimum drag was observed on the raked tip configuration and it was noted that the winglet wake lacked the cohesive vortex structure present in the wakes of the other configurations.
A study of the cornering forces generated by aircraft tires on a tilted, free-swiveling nose gear

NASA Technical Reports Server (NTRS)

Daugherty, R. H.; Stubbs, S. M.

1985-01-01

An experimental investigation was conducted to study the effect of various parameters on the cornering forces produced by a rolling aircraft tire installed on a tilted, free-swiveling nose gear. The parameters studied included tilt angle, trial, tire inflation pressure, rake angle, vertical load, and whether or not a twin tire configuration corotates. These parameters were evaluated by measuring the cornering force produced by an aircraft tire installed on the nose gear of a modified vehicle as it was towed slowly. Cornering force coefficient increased with increasing tilt angle. Increasing trial or rake angle decreased the magnitude of the cornering force coefficient. Tire inflation pressure had no effect on the cornering force coefficient. Increasing vertical load decreased the cornering force coefficient. When the tires of a twin tire system rotated independently, the cornering force coefficients were the same as those for the single-tire configuration. When the twin tire system was made to corotate, however, the cornering force coefficients increased significantly.
An Interactive Mobile Lecturing Model: Enhancing Student Engagement with Face-to-Face Sessions

ERIC Educational Resources Information Center

Boyinbode, Olutayo; Ng'ambi, Dick; Bagula, Antoine

2013-01-01

Although use of podcasts and vodcasts are increasingly becoming popular in higher education, their use is usually unidirectional and therefore replicates the transmission mode of traditional face-to-face lectures. In this paper, the authors propose a tool, MOBILect, a mobile lecturing tool that enables users to comment on lecture vodcasts using…
Study of the performances of nano-case treatment cutting tools on carbon steel work material during turning operation

NASA Astrophysics Data System (ADS)

Afolalu, S. A.; Okokpujie, I. P.; Salawu, E. Y.; Abioye, A. A.; Abioye, O. P.; Ikumapayi, O. M.

2018-04-01

The degree of holding temperature and time play a major role in nano-case treatment of cutting tools which immensely contributed to its performance during machining operation. The objective of this research work is to carryout comparative study of performance of nano-case treatment tools developed using low and medium carbon steel as work piece. Turning operation was carried out under two different categories with specific work piece on universal lathe machine using HSS cutting tools 100 mm × 12mm × 12mm that has been nano-case treated under varying conditions of temperatures and timeof 800,850, 900, 950°C and 60, 90, 120 mins respectively. The turning parameters used in evaluating this experiment were cutting speed of 270, 380 and 560mm/min, feed rate of 0.15, 0.20 and 0.25 mm/min, depth of cut of 2mm, work piece diameter of 25mm and rake angle of 7° each at three levels. The results of comparative study of their performances revealed that the timespent in the machining of low carbon steel material at a minimum temperature and time of 800°C, 60 mins were1.50, 2.17 mins while at maximum temperature and time of 950°C, 120 mins were 1.19, 2.02 mins. It was also observed that at a corresponding constant speed of 270,380 and 560mm/min at higher temperature and time, a relative increased in the length of cut were observed. Critical observation of the result showed that at higher case hardening temperature and time (950°C/120mins), the HSS cutting tool gave a better performance as lesser time was consumed during the turning operation.
Category-selective attention modulates unconscious processes in the middle occipital gyrus.

PubMed

Tu, Shen; Qiu, Jiang; Martens, Ulla; Zhang, Qinglin

2013-06-01

Many studies have revealed the top-down modulation (spatial attention, attentional load, etc.) on unconscious processing. However, there is little research about how category-selective attention could modulate the unconscious processing. In the present study, using functional magnetic resonance imaging (fMRI), the results showed that category-selective attention modulated unconscious face/tool processing in the middle occipital gyrus (MOG). Interestingly, MOG effects were of opposed direction for face and tool processes. During unconscious face processing, activation in MOG decreased under the face-selective attention compared with tool-selective attention. This result was in line with the predictive coding theory. During unconscious tool processing, however, activation in MOG increased under the tool-selective attention compared with face-selective attention. The different effects might be ascribed to an interaction between top-down category-selective processes and bottom-up processes in the partial awareness level as proposed by Kouider, De Gardelle, Sackur, and Dupoux (2010). Specifically, we suppose an "excessive activation" hypothesis. Copyright © 2013 Elsevier Inc. All rights reserved.
Remote repair appliance

DOEpatents

Heumann, Frederick K.; Wilkinson, Jay C.; Wooding, David R.

1997-01-01

A remote appliance for supporting a tool for performing work at a worksite on a substantially circular bore of a workpiece and for providing video signals of the worksite to a remote monitor comprising: a baseplate having an inner face and an outer face; a plurality of rollers, wherein each roller is rotatably and adjustably attached to the inner face of the baseplate and positioned to roll against the bore of the workpiece when the baseplate is positioned against the mouth of the bore such that the appliance may be rotated about the bore in a plane substantially parallel to the baseplate; a tool holding means for supporting the tool, the tool holding means being adjustably attached to the outer face of the baseplate such that the working end of the tool is positioned on the inner face side of the baseplate; a camera for providing video signals of the worksite to the remote monitor; and a camera holding means for supporting the camera on the inner face side of the baseplate, the camera holding means being adjustably attached to the outer face of the baseplate. In a preferred embodiment, roller guards are provided to protect the rollers from debris and a bore guard is provided to protect the bore from wear by the rollers and damage from debris.
Problems And Their Solutions When Thin-Walled Turned Parts Of High Precision With Quasi-Optical Surfaces Are Manufactured On A CNC Automatic Lathe Under Workshop Conditions

NASA Astrophysics Data System (ADS)

Jaeger, Valentin E.

1989-04-01

The geometrical accuracy and surface roughness of diamond-turned workpieces is influenced by several parameters: the properties of the machine tool, the cutting process and the environmental conditions. A thin-walled electrode made from an aluminium alloy (wall thickness: 1 mm, length: 169 mm, outer diameter: 126 mm) and intended for an electrostatic measuring instrument, serves as an example to show how quasi-optical surfaces with a surface roughness Rα < 10 nm and deviations from roundness of <= 5 μm can be achieved when some of these influence quantities are optimized. The cylindrical part of the electrode was turned by means of a rounded mirror-finish diamond tool, the width of the cutting edge being 2 mm, the rake angle -6° and the clearance angle 2°. Compliance with the tolerances of geometrical accuracy was particularly difficult. As age-hardened wrought aluminium alloys cannot be stress-relieved by annealing, or only insufficiently, the geometrical accuracy - in particular the roundness - of thin-walled, rotationally symmetric bodies decisively depends on the state of stress of the workpiece material, on the clamping fixture and on the balanced condition of this clamping fixture.
Exploring the influence of constitutive models and associated parameters for the orthogonal machining of Ti6Al4V

NASA Astrophysics Data System (ADS)

Pervaiz, S.; Anwar, S.; Kannan, S.; Almarfadi, A.

2018-04-01

Ti6Al4V is known as difficult-to-cut material due to its inherent properties such as high hot hardness, low thermal conductivity and high chemical reactivity. Though, Ti6Al4V is utilized by industrial sectors such as aeronautics, energy generation, petrochemical and bio-medical etc. For the metal cutting community, competent and cost-effective machining of Ti6Al4V is a challenging task. To optimize cost and machining performance for the machining of Ti6Al4V, finite element based cutting simulation can be a very useful tool. The aim of this paper is to develop a finite element machining model for the simulation of Ti6Al4V machining process. The study incorporates material constitutive models namely Power Law (PL) and Johnson – Cook (JC) material models to mimic the mechanical behaviour of Ti6Al4V. The study investigates cutting temperatures, cutting forces, stresses, and plastic strains with respect to different PL and JC material models with associated parameters. In addition, the numerical study also integrates different cutting tool rake angles in the machining simulations. The simulated results will be beneficial to draw conclusions for improving the overall machining performance of Ti6Al4V.
Effects of the six engine air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics

NASA Technical Reports Server (NTRS)

Mennell, R. C.; Soard, T.

1974-01-01

Experimental aerodynamic investigations were conducted on a 0.0405 scale representation of the -89B space shuttle orbiter in the 7.75 x 11.00 foot low speed wind tunnel during the time period September 4 - 14, 1973. The primary test objective was to optimize the air breathing propulsion system nacelle cowl-inlet design and to determine the aerodynamic effects of this design on the orbiter stability and control characteristics. Nacelle cowl-inlet optimization was determined from total pressure - static pressure measurements obtained from pressure rakes located in the left hand nacelle pod at the engine face station. After the optimum cow-inlet design, consisting of a 7 deg cowl lip angle, short cowl, 7 deg short diverter, and a nacelle toe-in angle of 5 deg was selected, the aerodynamic effects of various locations of this design were investigated. The 3 pod - 6 Nacelle configuration was tested both underwing and overwing in three different longitudinal locations. Orbiter control effectiveness, both with and without Nacelles, was investigated at elevon deflections of 0 deg, -10 deg and +15 deg and at aileron deflections of 0 deg and +10 deg about 0 deg elevon.
Smartphone based face recognition tool for the blind.

PubMed

Kramer, K M; Hedin, D S; Rolkosky, D J

2010-01-01

The inability to identify people during group meetings is a disadvantage for blind people in many professional and educational situations. To explore the efficacy of face recognition using smartphones in these settings, we have prototyped and tested a face recognition tool for blind users. The tool utilizes Smartphone technology in conjunction with a wireless network to provide audio feedback of the people in front of the blind user. Testing indicated that the face recognition technology can tolerate up to a 40 degree angle between the direction a person is looking and the camera's axis and a 96% success rate with no false positives. Future work will be done to further develop the technology for local face recognition on the smartphone in addition to remote server based face recognition.
9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...
9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...
Faculty Workload: An Analytical Approach

ERIC Educational Resources Information Center

Dennison, George M.

2012-01-01

Recent discussions of practices in higher education have tended toward muck-raking and self-styled exposure of cynical self-indulgence by faculty and administrators at the expense of students and their families, as usually occurs during periods of economic duress, rather than toward analytical studies designed to foster understanding This article…
Exploring Online Graduate Students' Responses to Online Self-Regulation Training

ERIC Educational Resources Information Center

Dunn, Karee E.; Rakes, Glenda C.

2015-01-01

In this study, online graduate students participated in four brief online self-regulatory trainings for self-efficacy, achievement goal orientation, learning strategies, and attributional thinking. These variables are critical to success in learning environments, but perhaps even more so in the online academic environment (Rakes, Dunn, &…
Resin film infusion mold tooling and molding method

NASA Technical Reports Server (NTRS)

Burgess, Roger (Inventor); Grossheim, Brian (Inventor); Mouradian, Karbis (Inventor); Thrash, Patrick J. (Inventor)

1999-01-01

A mold apparatus and method for resin film infusion molding including an outer mold tool having a facing sheet adapted to support a resin film and preform assembly. The facing sheet includes attachment features extending therefrom. An inner mold tool is positioned on the facing sheet to enclose the resin film and preform assembly for resin film infusion molding. The inner mold tool includes a plurality of mandrels positioned for engagement with the resin film and preform assembly. Each mandrel includes a slot formed therein. A plurality of locating bars cooperate with the slots and with the attachment features for locating the mandrels longitudinally on the outer mold tool.
Methods and systems for determining angular orientation of a drill string

DOEpatents

Cobern, Martin E.

2010-03-23

Preferred methods and systems generate a control input based on a periodically-varying characteristic associated with the rotation of a drill string. The periodically varying characteristic can be correlated with the magnetic tool face and gravity tool face of a rotating component of the drill string, so that the control input can be used to initiate a response in the rotating component as a function of gravity tool face.
An Earthquake Source Sensitivity Analysis for Tsunami Propagation in the Eastern Mediterranean

NASA Astrophysics Data System (ADS)

Necmioglu, Ocal; Meral Ozel, Nurcan

2013-04-01

An earthquake source parameter sensitivity analysis for tsunami propagation in the Eastern Mediterranean has been performed based on 8 August 1303 Crete and Dodecanese Islands earthquake resulting in destructive inundation in the Eastern Mediterranean. The analysis involves 23 cases describing different sets of strike, dip, rake and focal depth, while keeping the fault area and displacement, thus the magnitude, same. The main conclusions of the evaluation are drawn from the investigation of the wave height distributions at Tsunami Forecast Points (TFP). The earthquake vs. initial tsunami source parameters comparison indicated that the maximum initial wave height values correspond in general to the changes in rake angle. No clear depth dependency is observed within the depth range considered and no strike angle dependency is observed in terms of amplitude change. Directivity sensitivity analysis indicated that for the same strike and dip, 180° shift in rake may lead to 20% change in the calculated tsunami wave height. Moreover, an approximately 10 min difference in the arrival time of the initial wave has been observed. These differences are, however, greatly reduced in the far field. The dip sensitivity analysis, performed separately for thrust and normal faulting, has both indicated that an increase in the dip angle results in the decrease of the tsunami wave amplitude in the near field approximately 40%. While a positive phase shift is observed, the period and the shape of the initial wave stays nearly the same for all dip angles at respective TFPs. These affects are, however, not observed at the far field. The resolution of the bathymetry, on the other hand, is a limiting factor for further evaluation. Four different cases were considered for the depth sensitivity indicating that within the depth ranges considered (15-60 km), the increase of the depth has only a smoothing effect on the synthetic tsunami wave height measurements at the selected TFPs. The strike sensitivity analysis showed clear phase shift with respect to the variation of the strike angles, without leading to severe variation of the initial and maximum waves at locations considered. Travel time maps for two cases corresponding to difference in the strike value (60° vs 150°) presented a more complex wave propagation for the case with 60° strike angle due to the fact that the normal of the fault plane is orthogonal to the main bathymetric structure in the region, namely the Eastern section of the Hellenic Arc between Crete and Rhodes Islands. For a given set of strike, dip and focal depth parameters, the effect of the variation in the rake angle has been evaluated in the rake sensitivity analysis. A waveform envelope composed of symmetric synthetic recordings at one TFPs could be clearly observed as a result of rake angle variations in 0-180° range. This could also lead to the conclusion that for a given magnitude (fault size and displacement), the expected maximum and minimum tsunami wave amplitudes could be evaluated as a waveform envelope rather limited to a single point of time or amplitude. The Evaluation of the initial wave arrival times follows an expected pattern controlled by the distance, wheras maximum wave arrival time distribution presents no clear pattern. Nevertheless, the distribution is rather concentrated in time domain for some TFPs. Maximum positive and minimum negative wave amplitude distributions indicates a broader range for a subgroup of TFPs, wheras for the remaining TFPs the distributions are narrow. Any deviation from the expected trend of calculating narrower ranges of amplitude distributions could be interpreted as the result o the bathymetry and focusing effects. As similar studies conducted in the different parts of the globe indicated, the main characteristics of the tsunami propagation are unique for each basin. It should be noted, however, that the synthetic measurements obtained at the TFPs in the absence of high-resolution bathymetric data, should be considered only an overall guidance. The results indicate the importance of the accuracy of earthquake source parameters for reliable tsunami predictions and the need for high-resolution bathymetric data to be able to perform calculations with higher accuracy. On the other hand, this study did not address other parameters, such as heterogeneous slip distribution and rupture duration, which affect the tsunami initiation and propagation process.
Development and early application of the Scottish Community Nursing Workload Measurement Tool.

PubMed

Grafen, May; Mackenzie, Fiona C

2015-02-01

This article describes the development and early application of the Scottish Community Nursing Workload Measurement Tool, part of a suite of tools aiming to ensure a consistent approach to measuring nursing workload across NHS Scotland. The tool, which enables community nurses to record and report their actual workload by collecting information on six categories of activity, is now being used by all NHS boards as part of a triangulated approach. Data being generated by the tool at national level include indications that approximately 50% of band 6 district nurses' time is spent in face-to-face and non-face-to-face contact and planned sessions with patients, and that over 60% of face-to-face contacts are at 'moderate' and 'complex' levels of intervention (2012 data). These data are providing hard evidence of key elements of community nursing activity and practice that will enable informed decisions about workforce planning to be taken forward locally and nationally. The article features an account of the early impact of the tool's implementation in an NHS board by an associate director of nursing. Positive effects from implementation include the generation of reliable data to inform planning decisions, identification of issues around nursing time spent on administrative tasks, clarification of school nursing roles, and information being fed back to teams on various aspects of performance.
The Multimedia Case as a Tool for Professional Development: An Analysis of Online and Face-to-Face Interaction among Mathematics Pre-Service Teachers, In-Service Teachers, Mathematicians, and Mathematics Teacher Educators

ERIC Educational Resources Information Center

McGraw, Rebecca; Lynch, Kathleen; Koc, Yusuf; Budak, Ayfer; Brown, Catherine A.

2007-01-01

In this study, we consider the potential of multimedia cases as tools for teacher professional development. Specifically, we examined online and face-to-face discussions that occurred within groups composed of pre-service mathematics teachers, in-service mathematics teachers, mathematicians, and mathematics teacher educators. Discussions within…
Remote repair appliance

DOEpatents

Heumann, F.K.; Wilkinson, J.C.; Wooding, D.R.

1997-12-16

A remote appliance for supporting a tool for performing work at a work site on a substantially circular bore of a work piece and for providing video signals of the work site to a remote monitor comprises: a base plate having an inner face and an outer face; a plurality of rollers, wherein each roller is rotatably and adjustably attached to the inner face of the base plate and positioned to roll against the bore of the work piece when the base plate is positioned against the mouth of the bore such that the appliance may be rotated about the bore in a plane substantially parallel to the base plate; a tool holding means for supporting the tool, the tool holding means being adjustably attached to the outer face of the base plate such that the working end of the tool is positioned on the inner face side of the base plate; a camera for providing video signals of the work site to the remote monitor; and a camera holding means for supporting the camera on the inner face side of the base plate, the camera holding means being adjustably attached to the outer face of the base plate. In a preferred embodiment, roller guards are provided to protect the rollers from debris and a bore guard is provided to protect the bore from wear by the rollers and damage from debris. 5 figs.
Learning to Love Your Discovery Tool: Strategies for Integrating a Discovery Tool in Face-to-Face, Synchronous, and Asynchronous Instruction

ERIC Educational Resources Information Center

Fawley, Nancy; Krysak, Nikki

2014-01-01

Some librarians embrace discovery tools while others refuse to use them. This lack of consensus can have consequences for student learning when there is inconsistent use, especially in large-scale instruction programs. The authors surveyed academic librarians whose institutions have a discovery tool and who teach information literacy classes in…
Earth boring apparatus with multiple welds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bolton, J.B.; Crews, S.T.

1981-06-16

A box tool joint member of generally tubular configuration is adapted for securement by welding to one end of a steel tube to form a drill pipe. The box tool joint member comprises a body having a cylindrical outer periphery, an internally threaded socket at one end of the body, and a weld neck of smaller outer diameter than the body adjacent to the other end of the body. A tapered transition piece connecting the neck with the adjacent end of the body provides an elevator shoulder. A correlative pin tool joint member is welded to the opposite end ofmore » the tube to complete the drill pipe. The box tool joint member has an annular band of hard facing over the outer periphery of the transition piece and extending down over the adjacent part of the weld neck and up around the adjacent part of the body. The hard facing is corrosion resistant and has a smooth finished surface. Underneath the hard facing and extending beyond both ends of the hard facing is an annular butter layer of non-hardenable steel. The tool joint member is hardened and tempered after the butter layer is welded into a body groove and before the hard facing is welded on .The butter layer is grooved before the hard facing is welded on.« less
"Language Must Be Raked": Experience, Race, and the Pressure of Air

ERIC Educational Resources Information Center

Standish, Paul

2018-01-01

This article begins by clarifying the notion of what Stanley Cavell has called "Emersonian moral perfectionism." It goes on to explore this through close analysis of aspects of Emerson's essay "Experience," in which ideas of trying or attempting or experimenting bring out the intimate relation between perfectionism and styles…
46 CFR 32.63-20 - Hull structure-B/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... condition such that the forward rake bulkhead rests upon a pinnacle at the water surface, the maximum hull bending stress shall not exceed the following limits: (1) Independent tanks may be installed in such a... stress shall not exceed either 50 percent of the minimum ultimate tensile strength of the material or 70...
12. CLOSEUP OF THE CURRENT TRASH RAKELIFTING MECHANISM (CALLED 'JAWS' ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. CLOSE-UP OF THE CURRENT TRASH RAKE-LIFTING MECHANISM (CALLED 'JAWS' BY THE PRESENT OPERATORS), LOOKING WEST. THIS EQUIPMENT WAS REMOVED IN AUTUMN OF 1996. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID
Landscape in a Lacquer Box

ERIC Educational Resources Information Center

Savage, Martha

2010-01-01

A symbolic dry landscape garden of Eastern origin holds a special fascination for the author's middle-school students, which is why the author chose to create a project exploring this view of nature. A dry landscape garden, or "karesansui," is an arrangement of rocks, worn by nature and surrounded by a "sea" of sand, raked into patterns…
EFFECTS OF RECREATIONAL CLAM HARVESTING ON EELGRASS (ZOSTERA MARINA) AND ASSOCIATED INFAUNAL INVERTEBRATES: IN SITU MANIPULATIVE EXPERIMENTS

EPA Science Inventory

The effect of recreational clam harvesting on eelgrass (Zostera marina) was experimentally tested by raking or digging for clams in experimental 1-m2 plots located in a Yaquina Bay (Newport, OR) eelgrass meadow. After three monthly treatments, eelgrass measures of biomass, prima...
Performance Calculations for a Boundary-Layer-Ingesting Fan Stage from Sparse Measurements

NASA Technical Reports Server (NTRS)

Hirt, Stefanie M.; Wolter, John D.; Arend, David J.; Hearn, Tristan A.; Hardin, Larry W.; Gazzaniga, John A.

2018-01-01

A test of the Boundary Layer Ingesting-Inlet / Distortion-Tolerant Fan was completed in NASA Glenn's 8-Foot by 6-Foot supersonic wind tunnel. Inlet and fan performance were measured by surveys using a set of rotating rake arrays upstream and downstream of the fan stage. Surveys were conducted along the 100 percent speed line and a constant exit corrected flow line passing through the aerodynamic design point. These surveys represented only a small fraction of the data collected during the test. For other operating points, data was recorded as snapshots without rotating the rakes which resulted in a sparser set of recorded data. This paper will discuss analysis of these additional, lower measurement density data points to expand our coverage of the fan map. Several techniques will be used to supplement the snapshot data at test conditions where survey data also exists. The supplemented snapshot data will be compared with survey results to assess the quality of the approach. Effective methods will be used to analyze the data set for which only snapshots exist.
Pressure-sensing performance of upright cylinders in a Mach 10 boundary-layer

NASA Technical Reports Server (NTRS)

Johnson, Steven; Murphy, Kelly

1994-01-01

An experimental research program to provide basic knowledge of the pressure-sensing performance of upright, flushported cylinders in a hypersonic boundary layer is described. Three upright cylinders of 0.25-, 0.5- and l.0-in. diameters and a conventional rake were placed in the test section sidewall boundary layer of the 31 Inch Mach 10 Wind Tunnel at NASA Langley Research Center, Hampton, Virginia. Boundary-layer pressures from these cylinders were compared to those measured with a conventional rake. A boundary-layer thickness-to-cylinder-diameter ratio of 8 proved sufficient to accurately measure an overall pressure profile and ascertain the boundary-layer thickness. Effects of Reynolds number, flow angularity, and shock wave impingement on pressure measurement were also investigated. Although Reynolds number effects were negligible at the conditions studied, flow angularity above 10 deg significantly affects the measured pressures. Shock wave impingement was used to investigate orifice-to-orifice pressure crosstalk. No crosstalk was measured. The lower pressure measured above the oblique shock wave impingement showed no influence of the higher pressure generated at the lower port locations.
Release-ability of nano fillers from different nanomaterials (toward the acceptability of nanoproduct)

NASA Astrophysics Data System (ADS)

Golanski, L.; Guiot, A.; Pras, M.; Malarde, M.; Tardif, F.

2012-07-01

It is of great interest to set up a reproducible and sensitive method able to qualify nanomaterials before their market introduction in terms of their constitutive nanoparticle release-ability in usage. Abrasion was performed on polycarbonate, epoxy, and PA11 polymers containing carbone nanotubes (CNT) up to 4 %wt. Using Taber linear standard tool and standard abrasion conditions no release from polymer coatings containing CNT was measured. In this study, new practical tools inducing non-standardized stresses able to compete with van der Waals forces were developed and tested on model polymers, showing controlled CNT dispersion. These stresses are still realistic, corresponding to scratching, instantaneous mechanical shocks, and abrasion of the surface. They offer an efficient way to quantify if release is possible from nanomaterials under different mechanical stresses and therefore give an idea about the mechanisms that favors it. Release under mechanical shocks and hard abrasion was obtained using these tools but only when nanomaterials present a bad dispersion of CNT within the epoxy matrix. Under the same conditions no release was obtained from the same material presenting a good dispersion. The CNT used in this study showed an external diameter Dext = 12 nm, an internal diameter Din = 5 nm, and a mean length of 1 μm. Release from paints under hard abrasion using a standard rotative Taber tool was obtained from a intentionaly non-optimized paint containing SiO2 nanoparticles up to 35 %wt. The primary diameter of the SiO2 was estimated to be around 12 nm. A metallic rake was efficient to remove nanoparticles from a non-woven fabric nanomaterial.

There Is More than One Way to Crack an Oyster: Identifying Variation in Burmese Long-Tailed Macaque (Macaca fascicularis aurea) Stone-Tool Use

PubMed Central

Tan, Amanda; Tan, Say Hoon; Vyas, Dhaval; Malaivijitnond, Suchinda; Gumert, Michael D.

2015-01-01

We explored variation in patterns of percussive stone-tool use on coastal foods by Burmese long-tailed macaques (Macaca fascicularis aurea) from two islands in Laem Son National Park, Ranong, Thailand. We catalogued variation into three hammering classes and 17 action patterns, after examining 638 tool-use bouts across 90 individuals. Hammering class was based on the stone surface used for striking food, being face, point, and edge hammering. Action patterns were discriminated by tool material, hand use, posture, and striking motion. Hammering class was analyzed for associations with material and behavioural elements of tool use. Action patterns were not, owing to insufficient instances of most patterns. We collected 3077 scan samples from 109 macaques on Piak Nam Yai Island’s coasts, to determine the proportion of individuals using each hammering class and action pattern. Point hammering was significantly more associated with sessile foods, smaller tools, faster striking rates, smoother recoil, unimanual use, and more varied striking direction, than were face and edge hammering, while both point and edge hammering were significantly more associated with precision gripping than face hammering. Edge hammering also showed distinct differences depending on whether such hammering was applied to sessile or unattached foods, resembling point hammering for sessile foods and face hammering for unattached foods. Point hammering and sessile edge hammering compared to prior descriptions of axe hammering, while face and unattached edge hammering compared to pound hammering. Analysis of scans showed that 80% of individuals used tools, each employing one to four different action patterns. The most common patterns were unimanual point hammering (58%), symmetrical-bimanual face hammering (47%) and unimanual face hammering (37%). Unimanual edge hammering was relatively frequent (13%), compared to the other thirteen rare action patterns (<5%). We compare our study to other stone-using primates, and discuss implications for further research. PMID:25970286
Review and Comparison of Electronic Patient-Facing Family Health History Tools.

PubMed

Welch, Brandon M; Wiley, Kevin; Pflieger, Lance; Achiangia, Rosaline; Baker, Karen; Hughes-Halbert, Chanita; Morrison, Heath; Schiffman, Joshua; Doerr, Megan

2018-04-01

Family health history (FHx) is one of the most important pieces of information available to help genetic counselors and other clinicians identify risk and prevent disease. Unfortunately, the collection of FHx from patients is often too time consuming to be done during a clinical visit. Fortunately, there are many electronic FHx tools designed to help patients gather and organize their own FHx information prior to a clinic visit. We conducted a review and analysis of electronic FHx tools to better understand what tools are available, to compare and contrast to each other, to highlight features of various tools, and to provide a foundation for future evaluation and comparisons across FHx tools. Through our analysis, we included and abstracted 17 patient-facing electronic FHx tools and explored these tools around four axes: organization information, family history collection and display, clinical data collected, and clinical workflow integration. We found a large number of differences among FHx tools, with no two the same. This paper provides a useful review for health care providers, researchers, and patient advocates interested in understanding the differences among the available patient-facing electronic FHx tools.
11. VIEW SHOWING THE SUPERSTRUCTURE OF THE SHED ROOF (REMOVED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. VIEW SHOWING THE SUPERSTRUCTURE OF THE SHED ROOF (REMOVED AUTUMN OF 1996) PROTECTING THE PRESENT INTAKE GATES- AND RAKE-LIFTING MECHANISMS AND THE TRASH RACKS (LOWER FOREGROUND), LOOKING NORTH. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID
Behind the Scenes: Understanding Teacher Perspectives on Technology Integration in a Suburban District Technology Initiative

ERIC Educational Resources Information Center

Woolard, John

2012-01-01

Efforts to prepare students with skills necessary to compete in a 21st Century global, digital economy require technological literacy, but many teachers are inhibited by antiquated models of education and epistemological beliefs that leave them reluctant to integrate educational technologies in their content instruction (Dunn & Rakes, 2010;…
Computer Simulation of Replaceable Many Sider Plates (RMSP) with Enhanced Chip-Breaking Characteristics

NASA Astrophysics Data System (ADS)

Korchuganova, M.; Syrbakov, A.; Chernysheva, T.; Ivanov, G.; Gnedasch, E.

2016-08-01

Out of all common chip curling methods, a special tool face form has become the most widespread which is developed either by means of grinding or by means of profile pressing in the production process of RMSP. Currently, over 15 large tool manufacturers produce tools using instrument materials of over 500 brands. To this, we must add a large variety of tool face geometries, which purpose includes the control over form and dimensions of the chip. Taking into account all the many processed materials, specific tasks of the process planner, requirements to the quality of manufactured products, all this makes the choice of a proper tool which can perform the processing in the most effective way significantly harder. Over recent years, the nomenclature of RMSP for lathe tools with mechanical mounting has been considerably broadened by means of diversification of their faces
Factors Affecting Optimal Surface Roughness of AISI 4140 Steel in Turning Operation Using Taguchi Experiment

NASA Astrophysics Data System (ADS)

Novareza, O.; Sulistiyarini, D. H.; Wiradmoko, R.

2018-02-01

This paper presents the result of using Taguchi method in turning process of medium carbon steel of AISI 4140. The primary concern is to find the optimal surface roughness after turning process. The taguchi method is used to get a combination of factors and factor levels in order to get the optimum surface roughness level. Four important factors with three levels were used in experiment based on Taguchi method. A number of 27 experiments were carried out during the research and analysed using analysis of variance (ANOVA) method. The result of surface finish was determined in Ra type surface roughness. The depth of cut was found to be the most important factors for reducing the surface roughness of AISI 4140 steel. On the contrary, the other important factors i.e. spindle speed and rake side angle of the tool were proven to be less factors that affecting the surface finish. It is interesting to see the effect of coolant composition that gained the second important factors to reduce the roughness. It may need further research to explain this result.
The Earth isn't flat: The (large) influence of topography on geodetic fault slip imaging.

NASA Astrophysics Data System (ADS)

Thompson, T. B.; Meade, B. J.

2017-12-01

While earthquakes both occur near and generate steep topography, most geodetic slip inversions assume that the Earth's surface is flat. We have developed a new boundary element tool, Tectosaur, with the capability to study fault and earthquake problems including complex fault system geometries, topography, material property contrasts, and millions of elements. Using Tectosaur, we study the model error induced by neglecting topography in both idealized synthetic fault models and for the cases of the MW=7.3 Landers and MW=8.0 Wenchuan earthquakes. Near the steepest topography, we find the use of flat Earth dislocation models may induce errors of more than 100% in the inferred slip magnitude and rake. In particular, neglecting topographic effects leads to an inferred shallow slip deficit. Thus, we propose that the shallow slip deficit observed in several earthquakes may be an artefact resulting from the systematic use of elastic dislocation models assuming a flat Earth. Finally, using this study as an example, we emphasize the dangerous potential for forward model errors to be amplified by an order of magnitude in inverse problems.
Effect of Machining Parameters on Oxidation Behavior of Mild Steel

NASA Astrophysics Data System (ADS)

Majumdar, P.; Shekhar, S.; Mondal, K.

2015-01-01

This study aims to find out a correlation between machining parameters, resultant microstructure, and isothermal oxidation behavior of lathe-machined mild steel in the temperature range of 660-710 °C. The tool rake angles "α" used were +20°, 0°, and -20°, and cutting speeds used were 41, 232, and 541 mm/s. Under isothermal conditions, non-machined and machined mild steel samples follow parabolic oxidation kinetics with activation energy of 181 and ~400 kJ/mol, respectively. Exaggerated grain growth of the machined surface was observed, whereas, the center part of the machined sample showed minimal grain growth during oxidation at higher temperatures. Grain growth on the surface was attributed to the reduction of strain energy at high temperature oxidation, which was accumulated on the sub-region of the machined surface during machining. It was also observed that characteristic surface oxide controlled the oxidation behavior of the machined samples. This study clearly demonstrates the effect of equivalent strain, roughness, and grain size due to machining, and subsequent grain growth on the oxidation behavior of the mild steel.
High performance cutting using micro-textured tools and low pressure jet coolant

NASA Astrophysics Data System (ADS)

Obikawa, Toshiyuki; Nakatsukasa, Ryuta; Hayashi, Mamoru; Ohno, Tatsumi

2018-05-01

Tool inserts with different kinds of microtexture on the flank face were fabricated by laser irradiation for promoting the heat transfer from the tool face to the coolant. In addition to the micro-textured tools, jet coolant was applied to the tool tip from the side of the flank face, but under low-pressure conditions, to make Reynolds number of coolant as high as possible in the wedge shape zone between the tool flank and machined surface. First, the effect of jet coolant on the flank wear evolution was investigated using a tool without microtexture. The jet coolant showed an excellent improvement of the tool life in machining stainless steel SUS304 at higher cutting speeds. It was found that both the flow rate and velocity of jet coolant were indispensable to high performance cutting. Next, the effect of microtexture on the flank wear evolution was investigated using jet coolant. Three types of micro grooves extended tool life largely compared to the tool without microtexture. It was found that the depth of groove was one of important parameters affecting the tool life extension. As a result, the tool life was extended by more than l00 % using the microtextured tools and jet coolant compared to machining using flood coolant and a tool without microtexture.
Tools for Supporting Distributed Agile Project Planning

NASA Astrophysics Data System (ADS)

Wang, Xin; Maurer, Frank; Morgan, Robert; Oliveira, Josyleuda

Agile project planning plays an important part in agile software development. In distributed settings, project planning is severely impacted by the lack of face-to-face communication and the inability to share paper index cards amongst all meeting participants. To address these issues, several distributed agile planning tools were developed. The tools vary in features, functions and running platforms. In this chapter, we first summarize the requirements for distributed agile planning. Then we give an overview on existing agile planning tools. We also evaluate existing tools based on tool requirements. Finally, we present some practical advices for both designers and users of distributed agile planning tools.
An evaluation tool for Myofascial Adhesions in Patients after Breast Cancer (MAP-BC evaluation tool): Concurrent, face and content validity.

PubMed

De Groef, An; Van Kampen, Marijke; Moortgat, Peter; Anthonissen, Mieke; Van den Kerckhove, Eric; Christiaens, Marie-Rose; Neven, Patrick; Geraerts, Inge; Devoogdt, Nele

2018-01-01

To investigate the concurrent, face and content validity of an evaluation tool for Myofascial Adhesions in Patients after Breast Cancer (MAP-BC evaluation tool). 1) Concurrent validity of the MAP-BC evaluation tool was investigated by exploring correlations (Spearman's rank Correlation Coefficient) between the subjective scores (0 -no adhesions to 3 -very strong adhesions) of the skin level using the MAP-BC evaluation tool and objective elasticity parameters (maximal skin extension and gross elasticity) generated by the Cutometer Dual MPA 580. Nine different examination points on and around the mastectomy scar were evaluated. 2) Face and content validity were explored by questioning therapists experienced with myofascial therapy in breast cancer patients about the comprehensibility and comprehensiveness of the MAP-BC evaluation tool. 1) Only three meaningful correlations were found on the mastectomy scar. For the most lateral examination point on the mastectomy scar a moderate negative correlation (-0.44, p = 0.01) with the maximal skin extension and a moderate positive correlation with the resistance versus ability of returning or 'gross elasticity' (0.42, p = 0.02) were found. For the middle point on the mastectomy scar an almost moderate positive correlation with gross elasticity was found as well (0.38, p = 0.04) 2) Content and face validity have been found to be good. Eighty-nine percent of the respondent found the instructions understandable and 98% found the scoring system obvious. Thirty-seven percent of the therapists suggested to add the possibility to evaluate additional anatomical locations in case of reconstructive and/or bilateral surgery. The MAP-BC evaluation tool for myofascial adhesions in breast cancer patients has good face and content validity. Evidence for good concurrent validity of the skin level was found only on the mastectomy scar itself.
Developing a Data Set and Processing Methodology for Fluid/Structure Interaction Code Validation

DTIC Science & Technology

2007-06-01

50 29. 9-Probe Wake Survey Rake Configurations...structural stability and fatigue in test article components and, in general, in facility support structures and rotating machinery blading . Both T&E... blade analysis and simulations. To ensure the accuracy of the U of CO technology, validation using flight-test data and test data from a wind tunnel
Impacts of switchgrass intercropping in traditional pine forests on hydrology and water quality in the southeastern United States.

Treesearch

Devendra Amatya; G.M. Chescheir; J.E. Nettles

2016-01-01

Preliminary results indicate that switchgrass (Panicum virgatum L.), grown as a cellulosic biofuel between managed loblolly pine (Pinus taeda L.) beds on the Atlantic Coastal Plain forests has no significant effect on shallow ground water table and stream outflows. Although management operations (e.g. harvesting, shearing between pine rows, raking, and bedding)...
Project CHECO Southeast Asia Report. Operation DELAWARE 19 April - 17 May 1968

DTIC Science & Technology

1968-09-02

artillery delivered to LZs PEPPER and GOODMANT󈧸/ 25 (D+6) 3d Bde, 1st Cav Div, air-assaulted into LZ STALLION (A Luoi Airfield), 53/ Three 37-mm AAA guns...cases) 500 Beef bouillon qts) 10 Preserves (cases) 11 Pork and beef CHICOM) (qts) 1,125 MISCELLANEOUS ITEMS Barbed wire (rolls) 30 Pick, shovels, rakes
2. CLOSEUP OF SOUTH FACADE OF UPPER FALLS GATE HOUSE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. CLOSEUP OF SOUTH FACADE OF UPPER FALLS GATE HOUSE, SHOWING TRASH RACKS, REMOVABLE STEEL DOORS, TRASH RAKE STRUCTURE, AND DERRICK, WINCH AND CABLE GATE LIFTING DEVICE, LOOKING SOUTH/SOUTHWEST. - Washington Water Power Spokane River Upper Falls Hydroelectric Development, Gate House, Spokane River, approximately 0.5 mile northeast of intersection of Spokane Falls Boulevard & Post Street, Spokane, Spokane County, WA
Reliability Based Design for a Raked Wing Tip of an Airframe

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Coroneos, Rula M.

2011-01-01

A reliability-based optimization methodology has been developed to design the raked wing tip of the Boeing 767-400 extended range airliner made of composite and metallic materials. Design is formulated for an accepted level of risk or reliability. The design variables, weight and the constraints became functions of reliability. Uncertainties in the load, strength and the material properties, as well as the design variables, were modeled as random parameters with specified distributions, like normal, Weibull or Gumbel functions. The objective function and constraint, or a failure mode, became derived functions of the risk-level. Solution to the problem produced the optimum design with weight, variables and constraints as a function of the risk-level. Optimum weight versus reliability traced out an inverted-S shaped graph. The center of the graph corresponded to a 50 percent probability of success, or one failure in two samples. Under some assumptions, this design would be quite close to the deterministic optimum solution. The weight increased when reliability exceeded 50 percent, and decreased when the reliability was compromised. A design could be selected depending on the level of risk acceptable to a situation. The optimization process achieved up to a 20-percent reduction in weight over traditional design.
Determination Hypocentre and Focal Mechanism Earthquake of Oct 31, 2016 in Bone, South Sulawesi

NASA Astrophysics Data System (ADS)

Altin Massinai, Muhammad; Fawzy Ismullah M, Muhammad

2018-03-01

Indonesian Meteorology, Climatology and Geophysics Agency (BMKG) recorded an earthquake with M4.6 on at October 31, 2016 at Bone District, around 80 Km northeast form Makassar, South Sulawesi. The earthquake occurred 18:18:14 local time in 4.7°S, 120°E with depth 10 Km. Seismicity around location predicted caused by activity Walennae fault. We reprocessed earthquake data to determine precise hypocentre location and focal mechanism. The P- and S-wave arrival time got from BMKG used as input HYPOELLIPSE code to determine hypocentre. The results showed that the earthquake occurred 10:18:14.46 UTC in 4.638°S, 119.966°E with depth 24.76 Km. The hypocentre resolved 10 Km fix depth and had lower travel time residual than BMKG result. Focal mechanism determination used Azmtak code based on the first arrival polarity at earthquake waveform manually picked. The result showed a reverse mechanism with strike direction 38°, dip 44°, rake angle 134° on fault plane I and strike direction 164°, dip 60°, rake angle 56° on fault plane II. So, the earthquake which may be related to a reverse East Walennae Fault.
Modification of a liquid hydrogen tank for integrated refrigeration and storage

NASA Astrophysics Data System (ADS)

Swanger, A. M.; Jumper, K. M.; Fesmire, J. E.; Notardonato, W. U.

2015-12-01

The modification and outfitting of a 125,000-liter liquid hydrogen tank was performed to provide integrated refrigeration and storage capability. These functions include zero boil-off, liquefaction, and densification and therefore require provisions for sub-atmospheric tank pressures within the vacuum-jacketed, multilayer insulated tank. The primary structural modification was to add stiffening rings inside the inner vessel. The internal stiffening rings were designed, built, and installed per the ASME Boiler and Pressure Vessel Code, Section VIII, to prevent collapse in the case of vacuum jacket failure in combination with sub-atmospheric pressure within the tank. For the integrated refrigeration loop, a modular, skeleton-type heat exchanger, with refrigerant temperature instrumentation, was constructed using the stiffening rings as supports. To support the system thermal performance testing, three custom temperature rakes were designed and installed along the 21-meter length of the tank, once again using rings as supports. The temperature rakes included a total of 20 silicon diode temperature sensors mounted both vertically and radially to map the bulk liquid temperature within the tank. The tank modifications were successful and the system is now operational for the research and development of integrated refrigeration technology.
Formal implementation of a performance evaluation model for the face recognition system.

PubMed

Shin, Yong-Nyuo; Kim, Jason; Lee, Yong-Jun; Shin, Woochang; Choi, Jin-Young

2008-01-01

Due to usability features, practical applications, and its lack of intrusiveness, face recognition technology, based on information, derived from individuals' facial features, has been attracting considerable attention recently. Reported recognition rates of commercialized face recognition systems cannot be admitted as official recognition rates, as they are based on assumptions that are beneficial to the specific system and face database. Therefore, performance evaluation methods and tools are necessary to objectively measure the accuracy and performance of any face recognition system. In this paper, we propose and formalize a performance evaluation model for the biometric recognition system, implementing an evaluation tool for face recognition systems based on the proposed model. Furthermore, we performed evaluations objectively by providing guidelines for the design and implementation of a performance evaluation system, formalizing the performance test process.
The recalibration of tactile perception during tool use is body-part specific

PubMed Central

Cawley-Bennett, Andrew; Longo, Matthew R.; Saygin, Ayse P.

2018-01-01

Two decades of research have demonstrated that using a tool modulates spatial representations of the body. Whether this embodiment is specific to representations of the tool-using limb or extends to representations of other body parts has received little attention. Several studies of other perceptual phenomena have found that modulations to the primary somatosensory representation of the hand transfers to the face, due in part to their close proximity in primary somatosensory cortex. In the present study, we investigated whether tool-induced recalibration of tactile perception on the hand transfers to the cheek. Participants verbally estimated the distance between two tactile points applied to either their hand or face, before and after using a hand-shaped tool. Tool use recalibrated tactile distance perception on the hand—in line with previous findings—but left perception on the cheek unchanged. This finding provides support for the idea that embodiment is body-part specific. Furthermore, it suggests that tool-induced perceptual recalibration occurs at a level of somatosensory processing, where representations of the hand and face have become functionally disentangled. PMID:28702834

Development and validation of a nursing professionalism evaluation model in a career ladder system.

PubMed

Kim, Yeon Hee; Jung, Young Sun; Min, Ja; Song, Eun Young; Ok, Jung Hui; Lim, Changwon; Kim, Kyunghee; Kim, Ji-Su

2017-01-01

The clinical ladder system categorizes the degree of nursing professionalism and rewards and is an important human resource tool for managing nursing. We developed a model to evaluate nursing professionalism, which determines the clinical ladder system levels, and verified its validity. Data were collected using a clinical competence tool developed in this study, and existing methods such as the nursing professionalism evaluation tool, peer reviews, and face-to-face interviews to evaluate promotions and verify the presented content in a medical institution. Reliability and convergent and discriminant validity of the clinical competence evaluation tool were verified using SmartPLS software. The validity of the model for evaluating overall nursing professionalism was also analyzed. Clinical competence was determined by five dimensions of nursing practice: scientific, technical, ethical, aesthetic, and existential. The structural model explained 66% of the variance. Clinical competence scales, peer reviews, and face-to-face interviews directly determined nursing professionalism levels. The evaluation system can be used for evaluating nurses' professionalism in actual medical institutions from a nursing practice perspective. A conceptual framework for establishing a human resources management system for nurses and a tool for evaluating nursing professionalism at medical institutions is provided.
Looking east along the operating deck above the intake toward ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking east along the operating deck above the intake toward the Main Control Room. An evaporative-cooling system is to the left of the Control Room, and a motor-operated, geared trolly hoist and rake for removing debris from the trash rack is in the foreground - Wellton-Mohawk Irrigation System, Pumping Plant No. 1, Bounded by Gila River & Union Pacific Railroad, Wellton, Yuma County, AZ
Soil Profile Characteristics of a 25-Year-Old Windrowed Loblolly Pine Plantation in Louisiana

Treesearch

William B. Patterson; John C. Adams; Spencer E. Loe; R. Jarod Patterson

2002-01-01

Windrowing site preparation, the raking and piling of long rows of logging debris, has been reported to displace surface soil, redistribute nutrients, and reduce volume growth of southern pine forests. Many of these studies have reported short-term results, and there are few long-term studies of the effects of windrowing on soil properties and pine growth. A 16.2...
Eighteen-year response of slash pine to wet-weather harvesting and site preparation on a poorly drained silt loam soil in Louisiana

Treesearch

D. Andrew Scott; Allan E. Tiarks

2006-01-01

Physical disturbances to soil resulting from forest management operations may reduce tree survival and growth, but responses are soil-, species-, and disturbance-specific. We studied wet-weather harvesting, shearing, root-raking, disking, and phosphorus fertilization on a poorly drained flatwoods site in Louisiana. Slash pine survival was improved by wet-weather...
Slip complexity and frictional heterogeneities in dynamic fault models

NASA Astrophysics Data System (ADS)

Bizzarri, A.

2005-12-01

The numerical modeling of earthquake rupture requires the specification of the fault system geometry, the mechanical properties of the media surrounding the fault, the initial conditions and the constitutive law for fault friction. The latter accounts for the fault zone properties and allows for the description of processes of nucleation, propagation, healing and arrest of a spontaneous rupture. In this work I solve the fundamental elasto-dynamic equation for a planar fault, adopting different constitutive equations (slip-dependent and rate- and state-dependent friction laws). We show that the slip patterns may be complicated by different causes. The spatial heterogeneities of constitutive parameters are able to cause the healing of slip, like barrier-healing or slip pulses. Our numerical experiments show that the heterogeneities of the parameter L affect the dynamic rupture propagation and weakly modify the dynamic stress drop and the rupture velocity. The heterogeneity of a and b parameters affects the dynamic rupture propagation in a more complex way: a velocity strengthening area (a > b) can arrest a dynamic rupture, but can be driven to an instability if suddenly loaded by the dynamic rupture front. Our simulations provide a picture of the complex interactions between fault patches having different frictional properties. Moreover, the slip distribution on the fault plane is complicated considering the effects of the rake rotation during the propagation: depending on the position on the fault plane, the orientation of instantaneous total dynamic traction can change with time with respect to the imposed initial stress direction. These temporal rake rotations depend on the amplitude of the initial stress and on its distribution. They also depend on the curvature and direction of the rupture front with respect to the imposed initial stress direction: this explains why rake rotations are mostly located near the rupture front and within the cohesive zone, where the breakdown processes take places. Finally, the rupture behavior, the fault slip distribution and the traction evolution may be changed and complicated including additional physical phenomena, like thermal pressurization of pore fluid (due to frictional heating). Our results involve interesting implications for slip duration and fracture energy.
Simulated Firefighting Task Performance and Physiology Under Very Hot Conditions

PubMed Central

Larsen, Brianna; Snow, Rod; Williams-Bell, Michael; Aisbett, Brad

2015-01-01

Purpose: To assess the impact of very hot (45°C) conditions on the performance of, and physiological responses to, a simulated firefighting manual-handling task compared to the same work in a temperate environment (18°C). Methods: Ten male volunteer firefighters performed a 3-h protocol in both 18°C (CON) and 45°C (VH). Participants intermittently performed 12 × 1-min bouts of raking, 6 × 8-min bouts of low-intensity stepping, and 6 × 20-min rest periods. The area cleared during the raking task determined work performance. Core temperature, skin temperature, and heart rate were measured continuously. Participants also periodically rated their perceived exertion (RPE) and thermal sensation. Firefighters consumed water ad libitum. Urine specific gravity (USG) and changes in body mass determined hydration status. Results: Firefighters raked 19% less debris during the VH condition. Core and skin temperature were 0.99 ± 0.20 and 5.45 ± 0.53°C higher, respectively, during the VH trial, and heart rate was 14–36 beats.min−1 higher in the VH trial. Firefighters consumed 2950 ± 1034 mL of water in the VH condition, compared to 1290 ± 525 in the CON trial. Sweat losses were higher in the VH (1886 ± 474 mL) compared to the CON trial (462 ± 392 mL), though both groups were hydrated upon protocol completion (USG < 1.020). Participants' average RPE was higher in the VH (15.6 ± 0.9) compared to the CON trial (12.6 ± 0.9). Similarly, the firefighers' thermal sensation scores were significantly higher in the VH (6.4 ± 0.5) compared to the CON trial (4.4 ± 0.4). Conclusions: Despite the decreased work output and aggressive fluid replacement observed in the VH trial, firefighters' experienced increases in thermal stress, and exertion. Fire agencies should prioritize the health and safety of fire personnel in very hot temperatures, and consider the impact of reduced productivity on fire suppression efforts. PMID:26617527
Implementing standardized, inter-unit communication in an international setting: handoff of patients from emergency medicine to internal medicine.

PubMed

Balhara, Kamna S; Peterson, Susan M; Elabd, Mohamed Moheb; Regan, Linda; Anton, Xavier; Al-Natour, Basil Ali; Hsieh, Yu-Hsiang; Scheulen, James; Stewart de Ramirez, Sarah A

2018-04-01

Standardized handoffs may reduce communication errors, but research on handoff in community and international settings is lacking. Our study at a community hospital in the United Arab Emirates characterizes existing handoff practices for admitted patients from emergency medicine (EM) to internal medicine (IM), develops a standardized handoff tool, and assesses its impact on communication and physician perceptions. EM physicians completed a survey regarding handoff practices and expectations. Trained observers utilized a checklist based on the Systems Engineering Initiative for Patient Safety model to observe 40 handoffs. EM and IM physicians collaboratively developed a written tool encouraging bedside handoff of admitted patients. After the intervention, surveys of EM physicians and 40 observations were subsequently repeated. 77.5% of initial observed handoffs occurred face-to-face, with 42.5% at bedside, and in four different languages. Most survey respondents considered face-to-face handoff ideal. Respondents noted 9-13 patients suffering harm due to handoff in the prior month. After handoff tool implementation, 97.5% of observed handoffs occurred face-to-face (versus 77.5%, p = 0.014), with 82.5% at bedside (versus 42.5%, p < 0.001), and all in English. Handoff was streamlined from 7 possible pathways to 3. Most post-intervention survey respondents reported improved workflow (77.8%) and safety (83.3%); none reported patient harm. Respondents and observers noted reduced inefficiency (p < 0.05). Our standardized tool increased face-to-face and bedside handoff, positively impacted workflow, and increased perceptions of safety by EM physicians in an international, non-academic setting. Our three-step approach can be applied towards developing standardized, context-specific inter-specialty handoff in a variety of settings.
Mining planer with pivotal tool holder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun, E.; Braun, G.

1983-10-04

A planer assembly is disclosed for winning minerals from a mineral face comprising, a planer guide member, at least two planers slidably engaged on the guide member for movement in a travel direction along the face, a hinge interconnecting the two planers for transferring rotational moment applied to the planers and a planer tool holder mounted on each planer which carries a tool. The planer tool holder is positionable at an angle to make a cut of a selected depth with the depth increasing from planer to planer in a direction opposite the travel direction.
A brain-computer interface for potential non-verbal facial communication based on EEG signals related to specific emotions

PubMed Central

Kashihara, Koji

2014-01-01

Unlike assistive technology for verbal communication, the brain-machine or brain-computer interface (BMI/BCI) has not been established as a non-verbal communication tool for amyotrophic lateral sclerosis (ALS) patients. Face-to-face communication enables access to rich emotional information, but individuals suffering from neurological disorders, such as ALS and autism, may not express their emotions or communicate their negative feelings. Although emotions may be inferred by looking at facial expressions, emotional prediction for neutral faces necessitates advanced judgment. The process that underlies brain neuronal responses to neutral faces and causes emotional changes remains unknown. To address this problem, therefore, this study attempted to decode conditioned emotional reactions to neutral face stimuli. This direction was motivated by the assumption that if electroencephalogram (EEG) signals can be used to detect patients' emotional responses to specific inexpressive faces, the results could be incorporated into the design and development of BMI/BCI-based non-verbal communication tools. To these ends, this study investigated how a neutral face associated with a negative emotion modulates rapid central responses in face processing and then identified cortical activities. The conditioned neutral face-triggered event-related potentials that originated from the posterior temporal lobe statistically significantly changed during late face processing (600–700 ms) after stimulus, rather than in early face processing activities, such as P1 and N170 responses. Source localization revealed that the conditioned neutral faces increased activity in the right fusiform gyrus (FG). This study also developed an efficient method for detecting implicit negative emotional responses to specific faces by using EEG signals. A classification method based on a support vector machine enables the easy classification of neutral faces that trigger specific individual emotions. In accordance with this classification, a face on a computer morphs into a sad or displeased countenance. The proposed method could be incorporated as a part of non-verbal communication tools to enable emotional expression. PMID:25206321
A brain-computer interface for potential non-verbal facial communication based on EEG signals related to specific emotions.

PubMed

Kashihara, Koji

2014-01-01

Unlike assistive technology for verbal communication, the brain-machine or brain-computer interface (BMI/BCI) has not been established as a non-verbal communication tool for amyotrophic lateral sclerosis (ALS) patients. Face-to-face communication enables access to rich emotional information, but individuals suffering from neurological disorders, such as ALS and autism, may not express their emotions or communicate their negative feelings. Although emotions may be inferred by looking at facial expressions, emotional prediction for neutral faces necessitates advanced judgment. The process that underlies brain neuronal responses to neutral faces and causes emotional changes remains unknown. To address this problem, therefore, this study attempted to decode conditioned emotional reactions to neutral face stimuli. This direction was motivated by the assumption that if electroencephalogram (EEG) signals can be used to detect patients' emotional responses to specific inexpressive faces, the results could be incorporated into the design and development of BMI/BCI-based non-verbal communication tools. To these ends, this study investigated how a neutral face associated with a negative emotion modulates rapid central responses in face processing and then identified cortical activities. The conditioned neutral face-triggered event-related potentials that originated from the posterior temporal lobe statistically significantly changed during late face processing (600-700 ms) after stimulus, rather than in early face processing activities, such as P1 and N170 responses. Source localization revealed that the conditioned neutral faces increased activity in the right fusiform gyrus (FG). This study also developed an efficient method for detecting implicit negative emotional responses to specific faces by using EEG signals. A classification method based on a support vector machine enables the easy classification of neutral faces that trigger specific individual emotions. In accordance with this classification, a face on a computer morphs into a sad or displeased countenance. The proposed method could be incorporated as a part of non-verbal communication tools to enable emotional expression.
High speed transition prediction

NASA Technical Reports Server (NTRS)

Gasperas, Gediminis

1992-01-01

The main objective of this work period was to develop, acquire and apply state-of-the-art tools for the prediction of transition at high speeds at NASA Ames. Although various stability codes as well as basic state codes were acquired, the development of a new Parabolized Stability Equation (PSE) code was minimal. The time that was initially allocated for development was used on other tasks, in particular for the Leading Edge Suction problem, in acquiring proficiency in various graphics tools, and in applying these tools to evaluate various Navier-Stokes and Euler solutions. The second objective of this work period was to attend the Transition and Turbulence Workshop at NASA Langley in July and August, 1991. A report on the Workshop follows. From July 8, 1991 to August 2, 1991, the author participated in the Transition and Turbulence Workshop at NASA Langley. For purposes of interest here, analysis can be said to consist of solving simplified governing equations by various analytical methods, such as asymptotic methods, or by use of very meager computer resources. From the composition of the various groups at the Workshop, it can be seen that analytical methods are generally more popular in Great Britain than they are in the U.S., possibly due to historical factors and the lack of computer resources. Experimenters at the Workshop were mostly concerned with subsonic flows, and a number of demonstrations were provided, among which were a hot-wire experiment to probe the boundary layer on a rotating disc, a hot-wire rake to map a free shear layer behind a cylinder, and the use of heating strips on a flat plate to control instability waves and consequent transition. A highpoint of the demonstrations was the opportunity to observe the rather noisy 'quiet' supersonic pilot tunnel in operation.
Computer tools for face seal analyses developed at John Crane

NASA Technical Reports Server (NTRS)

Wu, Shifeng

1994-01-01

The purposes of the computer tools for face seal analysis are new product optimization, existing seals on new applications, existing seals on off-duty conditions, and trouble-shooting. Discussed in this viewgraph presentation are interface forces, friction/heat generation, heat transfer/temperature distribution, axisymmetric pressure/thermal distortion, leakage, and an example case.
Discussion Tool Effects on Collaborative Learning and Social Network Structure

ERIC Educational Resources Information Center

Tomsic, Astrid; Suthers, Daniel D.

2006-01-01

This study investigated the social network structure of booking officers at the Honolulu Police Department and how the introduction of an online discussion tool affected knowledge about operation of a booking module. Baseline data provided evidence for collaboration among officers in the same district using e-mail, telephone and face-to-face media…
A Face-to-Face Professional Development Model to Enhance Teaching of Online Research Strategies

ERIC Educational Resources Information Center

Terrazas-Arellanes, Fatima E.; Knox, Carolyn; Strycker, Lisa A.; Walden, Emily

2016-01-01

To help students navigate the digital environment, teachers not only need access to the right technology tools but they must also engage in pedagogically sound, high-quality professional development. For teachers, quality professional development can mean the difference between merely using technology tools and creating transformative change in…
Obstacles to Enhancing Professional Development with Digital Tools in Rural Landscapes

ERIC Educational Resources Information Center

Hunt-Barron, Sarah; Tracy, Kelly N.; Howell, Emily; Kaminski, Rebecca

2015-01-01

This case study examines the use of online tools, including blogs, as a means of enhancing face-to-face professional development in writing instruction for teachers in rural districts. Since many rural districts serve large physical areas that are geographically distant from larger metropolitan areas and/or colleges and universities, teachers in…
EUnetHTA information management system: development and lessons learned.

PubMed

Chalon, Patrice X; Kraemer, Peter

2014-11-01

The aim of this study was to describe the techniques used in achieving consensus on common standards to be implemented in the EUnetHTA Information Management System (IMS); and to describe how interoperability between tools was explored. Three face to face meetings were organized to identify and agree on common standards to the development of online tools. Two tools were created to demonstrate the added value of implementing interoperability standards at local levels. Developers of tools outside EUnetHTA were identified and contacted. Four common standards have been agreed on by consensus; and consequently all EUnetHTA tools have been modified or designed accordingly. RDF Site Summary (RSS) has demonstrated a good potential to support rapid dissemination of HTA information. Contacts outside EUnetHTA resulted in direct collaboration (HTA glossary, HTAi Vortal), evaluation of options for interoperability between tools (CRD HTA database) or a formal framework to prepare cooperation on concrete projects (INAHTA projects database). While being entitled a project on IT infrastructure, the work program was also about people. When having to agree on complex topics, fostering a cohesive group dynamic and hosting face to face meetings brings added value and enhances understanding between partners. The adoption of widespread standards enhanced the homogeneity of the EUnetHTA tools and should thus contribute to their wider use, therefore, to the general objective of EUnetHTA. The initiatives on interoperability of systems need to be developed further to support a general interoperable information system that could benefit the whole HTA community.
Development, implementation and evaluation of a patient handoff tool to improve safety in orthopaedic surgery.

PubMed

Gagnier, Joel J; Derosier, Joseph M; Maratt, Joseph D; Hake, Mark E; Bagian, James P

2016-06-01

To develop, implement and test the effect of a handoff tool for orthopaedic trauma residents that reduces adverse events associated with the omission of critical information and the transfer of erroneous information. Components of this project included a literature review, resident surveys and observations, checklist development and refinement, implementation and evaluation of impact on adverse events through a chart review of a prospective cohort compared with a historical control group. Large teaching hospital. Findings of a literature review were presented to orthopaedic residents, epidemiologists, orthopaedic surgeons and patient safety experts in face-to-face meetings, during which we developed and refined the contents of a resident handoff tool. The tool was tested in an orthopaedic trauma service and its impact on adverse events was evaluated through a chart review. The handoff tool was developed and refined during the face-to-face meetings and a pilot implementation. Adverse event data were collected on 127 patients (n = 67 baseline period; n = 60 test period). A handoff tool for use by orthopaedic residents. Adverse events in patients handed off by orthopaedic trauma residents. After controlling for age, gender and comorbidities, testing resulted in fewer events per person (25-27% reduction; P < 0.10). Preliminary evidence suggests that our resident handoff tool may contribute to a decrease in adverse events in orthopaedic patients. © The Author 2016. Published by Oxford University Press in association with the International Society for Quality in Health Care; all rights reserved.
The Cambridge Face Memory Test for Children (CFMT-C): a new tool for measuring face recognition skills in childhood.

PubMed

Croydon, Abigail; Pimperton, Hannah; Ewing, Louise; Duchaine, Brad C; Pellicano, Elizabeth

2014-09-01

Face recognition ability follows a lengthy developmental course, not reaching maturity until well into adulthood. Valid and reliable assessments of face recognition memory ability are necessary to examine patterns of ability and disability in face processing, yet there is a dearth of such assessments for children. We modified a well-known test of face memory in adults, the Cambridge Face Memory Test (Duchaine & Nakayama, 2006, Neuropsychologia, 44, 576-585), to make it developmentally appropriate for children. To establish its utility, we administered either the upright or inverted versions of the computerised Cambridge Face Memory Test - Children (CFMT-C) to 401 children aged between 5 and 12 years. Our results show that the CFMT-C is sufficiently sensitive to demonstrate age-related gains in the recognition of unfamiliar upright and inverted faces, does not suffer from ceiling or floor effects, generates robust inversion effects, and is capable of detecting difficulties in face memory in children diagnosed with autism. Together, these findings indicate that the CFMT-C constitutes a new valid assessment tool for children's face recognition skills. Copyright © 2014 Elsevier Ltd. All rights reserved.
Comparative Study on the Performance of Bachelor of Secondary Education (BSE) Students in Educational Technology Using Blended Learning Strategy and Traditional Face-to-Face Instruction

ERIC Educational Resources Information Center

Lorenzo, Arnold R.

2017-01-01

Technology offers various tools of improving the teaching -- learning process. It revolutionizes teaching from traditional face-to-face to distance and online learning. This study described and compared the performance of BSE II students in educational technology using the traditional face-to-face classroom interaction and the blended learning…
A self-report critical incident assessment tool for army night vision goggle helicopter operations.

PubMed

Renshaw, Peter F; Wiggins, Mark W

2007-04-01

The present study sought to examine the utility of a self-report tool that was designed as a partial substitute for a face-to-face cognitive interview for critical incidents involving night vision goggles (NVGs). The use of NVGs remains problematic within the military environment, as these devices have been identified as a factor in a significant proportion of aircraft accidents and incidents. The self-report tool was structured to identify some of the cognitive features of human performance that were associated with critical incidents involving NVGs. The tool incorporated a number of different levels of analysis, ranging from specific behavioral responses to broader cognitive constructs. Reports were received from 30 active pilots within the Australian Army using the NVG Critical Incident Assessment Tool (NVGCIAT). The results revealed a correspondence between specific types of NVG-related errors and elements of the Human Factors Analysis and Classification System (HFACS). In addition, uncertainty emerged as a significant factor associated with the critical incidents that were recalled by operators. These results were broadly consistent with previous research and provide some support for the utility of subjective assessment tools as a means of extracting critical incident-related data when face-to-face cognitive interviews are not possible. In some circumstances, the NVGCIAT might be regarded as a substitute cognitive interview protocol with some level of diagnosticity.

Fundamental Studies of SUBSONIC and Transonic Flow Separation. Part 3. Third Phase Summary Report

DTIC Science & Technology

1979-10-01

circular bump using a laser velocimeter and pitot probe. They point out that external probes like pitot probes or rakes of different kinds may...numerical Navier-Stokes solutions for high Reynolds number two-dimenslonal flow. The flow conditions have been extended to include low supersonic free...Setups . . . . . . . . . . . 19 Shock Holder and Its Orientation in the Tunnel . . . . . . . . . . . . . . 21 Pitot and Cone Probes Mounted on
Unsteady Force Calculations in Turbomachinery

DTIC Science & Technology

1991-07-01

Engineering for Gas Turbines and Power, Vol. 107, pp. 945-952, October 1985. Lefcort, M. P., "An Investigation into Unsteady Blade Forces in...generated unsteady flow around a rotating turbine blade row .. ..... 43 7 The rotating coordinate system with skew, 0, and rake, zr, defined at midchord...while Kerrebrock and Mikolajczak [19701 5 proved it experimentally. For a turbine blade passage, the wake fluid moves from the pressure 3 surface to the
Comparison of three site preparation techniques on growth of planted loblolly pine 6 years after a southern pine beetle epidemic

Treesearch

Wayne K. Clatterbuck; Michael Carr

2013-01-01

Three site preparation treatments: (1) complete removal of woody debrisâdrum chopped, raked, and disked; (2) drum chopping leaving woody debris; and (3) no site preparationâplanting among dead standing trees were compared by evaluating the growth and survival of planted loblolly pine (Pinus taeda L.) after six growing seasons following a southern...
Analysis of Building 839: Carlisle Barracks, Pennsylvania

DTIC Science & Technology

2013-09-01

within prehistory or history is made clear.”101 A historic property is determined as either significant or not significant by applying standardized...yielded, or is likely to yield, information important in prehistory or history. 3.3 Significance Eligibility to the NRHP is based upon...given period in history or prehistory . The workmanship of Building 839 is evident in the mortar joints of the brick walls (Figure 53), the rake boards
Selectivity for the human body in the fusiform gyrus.

PubMed

Peelen, Marius V; Downing, Paul E

2005-01-01

Functional neuroimaging studies have revealed human brain regions, notably in the fusiform gyrus, that respond selectively to images of faces as opposed to other kinds of objects. Here we use fMRI to show that the mid-fusiform gyrus responds with nearly the same level of selectivity to images of human bodies without faces, relative to tools and scenes. In a group-average analysis (n = 22), the fusiform activations identified by contrasting faces versus tools and bodies versus tools are very similar. Analyses of within-subjects regions of interest, however, show that the peaks of the two activations occupy close but distinct locations. In a second experiment, we find that the body-selective fusiform region, but not the face-selective region, responds more to stick figure depictions of bodies than to scrambled controls. This result further distinguishes the two foci and confirms that the body-selective response generalizes to abstract image formats. These results challenge accounts of the mid-fusiform gyrus that focus solely on faces and suggest that this region contains multiple distinct category-selective neural representations.
Radial and circumferential flow surveys at the inlet and exit of the Space Shuttle Main Engine High Pressure Fuel Turbine Model

NASA Technical Reports Server (NTRS)

Hudson, S. T.; Bordelon, W. J., Jr.; Smith, A. W.; Ramachandran, N.

1995-01-01

The main objective of this test was to obtain detailed radial and circumferential flow surveys at the inlet and exit of the SSME High Pressure Fuel Turbine model using three-hole cobra probes, hot-film probes, and a laser velocimeter. The test was designed to meet several objectives. First, the techniques for making laser velocimeter, hot-film probe, and cobra probe measurements in turbine flows were developed and demonstrated. The ability to use the cobra probes to obtain static pressure and, therefore, velocity had to be verified; insertion techniques had to be established for the fragile hot-film probes; and a seeding method had to be established for the laser velocimetry. Once the measurement techniques were established, turbine inlet and exit velocity profiles, temperature profiles, pressure profiles, turbulence intensities, and boundary layer thicknesses were measured at the turbine design point. The blockage effect due to the model inlet and exit total pressure and total temperature rakes on the turbine performance was also studied. A small range of off-design points were run to obtain the profiles and to verify the rake blockage effects off-design. Finally, a range of different Reynolds numbers were run to study the effect of Reynolds number on the various measurements.
Flow-Field Survey in the Test Region of the SR-71 Aircraft Test Bed Configuration

NASA Technical Reports Server (NTRS)

Mizukami, Masashi; Jones, Daniel; Weinstock, Vladimir D.

2000-01-01

A flat plate and faired pod have been mounted on a NASA SR-71A aircraft for use as a supersonic flight experiment test bed. A test article can be placed on the flat plate; the pod can contain supporting systems. A series of test flights has been conducted to validate this test bed configuration. Flight speeds to a maximum of Mach 3.0 have been attained. Steady-state sideslip maneuvers to a maximum of 2 deg have been conducted, and the flow field in the test region has been surveyed. Two total-pressure rakes, each with two flow-angle probes, have been placed in the expected vicinity of an experiment. Static-pressure measurements have been made on the flat plate. At subsonic and low supersonic speeds with no sideslip, the flow in the surveyed region is quite uniform. During sideslip maneuvers, localized flow distortions impinge on the test region. Aircraft sideslip does not produce a uniform sidewash over the test region. At speeds faster than Mach 1.5, variable-pressure distortions were observed in the test region. Boundary-layer thickness on the flat plate at the rake was less than 2.1 in. For future experiments, a more focused and detailed flow-field survey than this one would be desirable.
Wind Code Application to External Forebody Flowfields with Comparisons to Experimental Results

NASA Technical Reports Server (NTRS)

Frate, F. C.; Kim, H. D.

2001-01-01

The WIND Code, a general purpose Navier-Stokes solver, has been utilized to obtain supersonic external flowfield Computational Fluid Dynamics (CFD) solutions over an axisymmetric, parabolic forebody with comparisons made to wind tunnel experimental results. Various cases have been investigated at supersonic freestream conditions ranging from Mach 2.0 to 3.5, at 0 deg and 3 deg angles-of-attack, and with either a sharp-nose or blunt-nose forebody configuration. Both a turbulent (Baldwin-Lomax algebraic turbulence model) and a laminar model have been implemented in the CFD. Obtaining the solutions involved utilizing either the parabolized- or full-Navier-Stokes analyses supplied in WIND. Comparisons have been made with static pressure measurements, with boundary-layer rake and flowfield rake pitot pressure measurements, and with temperature sensitive paint experimental results. Using WIND's parabolized Navier-Stokes capability, grid sequencing, and the Baldwin-Lomax algebraic turbulence model allowed for significant reductions in computational time while still providing good agreement with experiment. Given that CFD and experiment compare well, WIND is found to be a good computational platform for solving this type of forebody problem, and the grids developed in conjunction with it will be used in the future to investigate varying freestream conditions not tested experimentally.
Quantitative determination of microbial activity and community nutritional status in estuarine sediments: evidence for a disturbance artifact

NASA Technical Reports Server (NTRS)

Findlay, R. H.; Pollard, P. C.; Moriarty, D. J.; White, D. C.

1985-01-01

In estuarine sediments with a high degree of vertical heterogeneity in reduced substrate and terminal electron acceptor concentrations, the method of exposure of the microbiota to labeled substrates can introduce a "disturbance artifact" into measures of metabolic activity. The detection of this artifact is based on quantitative measurement of the relative rates of incorporation of [14C]acetate into phospholipid fatty acids (PLFA) and endogenous storage lipid, poly-beta-hydroxyalkanoate (PHA). Previous studies have shown that PLFA synthesis measures cellular growth and that PHA synthesis measures carbon accumulation (unbalanced growth). The "disturbance artifact" of exposure to [14C]acetate was demonstrated by comparing injection of a core with the usual or pore-water replacement or slurry techniques. Only injection of labeled substrate allowed detection of preassay disturbance of the sediment with a garden rake. The raking increased PLFA synthesis with little effect to differences in concentration or distribution of [14C]acetate in the 10-min incubation. Bioturbation induced by sand dollar feeding in estuarine sediment could be detected in an increased PLFA/PHA ratio which was due to decreased PHA synthesis if the addition of labeled substrate was by the injection technique. Addition of labeled precursors to sediment by slurry or pore-water replacement induces greater disturbance artifacts than injection techniques.
CFD Models of a Serpentine Inlet, Fan, and Nozzle

NASA Technical Reports Server (NTRS)

Chima, R. V.; Arend, D. J.; Castner, R. S.; Slater, J. W.; Truax, P. P.

2010-01-01

Several computational fluid dynamics (CFD) codes were used to analyze the Versatile Integrated Inlet Propulsion Aerodynamics Rig (VIIPAR) located at NASA Glenn Research Center. The rig consists of a serpentine inlet, a rake assembly, inlet guide vanes, a 12-in. diameter tip-turbine driven fan stage, exit rakes or probes, and an exhaust nozzle with a translating centerbody. The analyses were done to develop computational capabilities for modeling inlet/fan interaction and to help interpret experimental data. Three-dimensional Reynolds averaged Navier-Stokes (RANS) calculations of the fan stage were used to predict the operating line of the stage, the effects of leakage from the turbine stream, and the effects of inlet guide vane (IGV) setting angle. Coupled axisymmetric calculations of a bellmouth, fan, and nozzle were used to develop techniques for coupling codes together and to investigate possible effects of the nozzle on the fan. RANS calculations of the serpentine inlet were coupled to Euler calculations of the fan to investigate the complete inlet/fan system. Computed wall static pressures along the inlet centerline agreed reasonably well with experimental data but computed total pressures at the aerodynamic interface plane (AIP) showed significant differences from the data. Inlet distortion was shown to reduce the fan corrected flow and pressure ratio, and was not completely eliminated by passage through the fan
Development of AMSTAR: a measurement tool to assess the methodological quality of systematic reviews.

PubMed

Shea, Beverley J; Grimshaw, Jeremy M; Wells, George A; Boers, Maarten; Andersson, Neil; Hamel, Candyce; Porter, Ashley C; Tugwell, Peter; Moher, David; Bouter, Lex M

2007-02-15

Our objective was to develop an instrument to assess the methodological quality of systematic reviews, building upon previous tools, empirical evidence and expert consensus. A 37-item assessment tool was formed by combining 1) the enhanced Overview Quality Assessment Questionnaire (OQAQ), 2) a checklist created by Sacks, and 3) three additional items recently judged to be of methodological importance. This tool was applied to 99 paper-based and 52 electronic systematic reviews. Exploratory factor analysis was used to identify underlying components. The results were considered by methodological experts using a nominal group technique aimed at item reduction and design of an assessment tool with face and content validity. The factor analysis identified 11 components. From each component, one item was selected by the nominal group. The resulting instrument was judged to have face and content validity. A measurement tool for the 'assessment of multiple systematic reviews' (AMSTAR) was developed. The tool consists of 11 items and has good face and content validity for measuring the methodological quality of systematic reviews. Additional studies are needed with a focus on the reproducibility and construct validity of AMSTAR, before strong recommendations can be made on its use.
Pre-Finishing of SiC for Optical Applications

NASA Technical Reports Server (NTRS)

Rozzi, Jay; Clavier, Odile; Gagne, John

2011-01-01

13 Manufacturing & Prototyping A method is based on two unique processing steps that are both based on deterministic machining processes using a single-point diamond turning (SPDT) machine. In the first step, a high-MRR (material removal rate) process is used to machine the part within several microns of the final geometry. In the second step, a low-MRR process is used to machine the part to near optical quality using a novel ductile regime machining (DRM) process. DRM is a deterministic machining process associated with conditions under high hydrostatic pressures and very small depths of cut. Under such conditions, using high negative-rake angle cutting tools, the high-pressure region near the tool corresponds to a plastic zone, where even a brittle material will behave in a ductile manner. In the high-MRR processing step, the objective is to remove material with a sufficiently high rate such that the process is economical, without inducing large-scale subsurface damage. A laser-assisted machining approach was evaluated whereby a CO2 laser was focused in advance of the cutting tool. While CVD (chemical vapor deposition) SiC was successfully machined with this approach, the cutting forces were substantially higher than cuts at room temperature under the same machining conditions. During the experiments, the expansion of the part and the tool due to the heating was carefully accounted for. The higher cutting forces are most likely due to a small reduction in the shear strength of the material compared with a larger increase in friction forces due to the thermal softening effect. The key advantage is that the hybrid machine approach has the potential to achieve optical quality without the need for a separate optical finishing step. Also, this method is scalable, so one can easily progress from machining 50-mm-diameter samples to the 250-mm-diameter mirror that NASA desires.
Developmental Changes in Face Recognition during Childhood: Evidence from Upright and Inverted Faces

ERIC Educational Resources Information Center

de Heering, Adelaide; Rossion, Bruno; Maurer, Daphne

2012-01-01

Adults are experts at recognizing faces but there is controversy about how this ability develops with age. We assessed 6- to 12-year-olds and adults using a digitized version of the Benton Face Recognition Test, a sensitive tool for assessing face perception abilities. Children's response times for correct responses did not decrease between ages 6…
Dimensions of Small Unit Resilience in Organizations Facing Threats, Disruption, and Stress

DTIC Science & Technology

2011-06-15

upbeat. ‘He was looking forward to getting back to Iraq,’ Scott recalls. ‘He missed his buddies. He wanted to learn to play the guitar when he got...the face of adversity,), as well as, a tool to mathematically measure and score the results. One possible solution is that survey questions on...resilience could be added to existing tools and scored separately, or a separate survey could be conducted in conjunction with the other tools
Can Water-Injected Turbomachines Provide Cost-Effective Emissions and Maintenance Reductions?

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Daggett, David L.; Shouse, Dale T.; Roquemore, William M.; Brankovic, Andreja; Ryder, Robert C., Jr.

2011-01-01

An investigation has been performed to evaluate the effect of water injection on the performance of the Air Force Research Laboratory (AFRL, Wright-Patterson Air Force Base (WPAFB)) experimental trapped vortex combustor (TVC) over a range of fuel-to-air and water-to-fuel ratios. Performance is characterized by combustor exit quantities: temperature and emissions measurements using rakes, and overall pressure drop, from upstream plenum to combustor exit. Combustor visualization is performed using gray-scale and color still photographs and high-frame-rate videos. A parallel investigation evaluated the performance of a computational fluid dynamics (CFD) tool for the prediction of the reacting flow in a liquid fueled combustor (e.g., TVC) that uses water injection for control of pollutant emissions and turbine inlet temperature. Generally, reasonable agreement is found between data and NO(x) computations. Based on a study assessing the feasibility and performance impact of using water injection on a Boeing 747-400 aircraft to reduce NO(x) emissions during takeoff, retrofitting does not appear to be cost effective; however, an operator of a newly designed engine and airframe might be able to save up to 1.0 percent in operating costs. Other challenges of water injection will be discussed.
Design and testing of coring bits on drilling lunar rock simulant

NASA Astrophysics Data System (ADS)

Li, Peng; Jiang, Shengyuan; Tang, Dewei; Xu, Bo; Ma, Chao; Zhang, Hui; Qin, Hongwei; Deng, Zongquan

2017-02-01

Coring bits are widely utilized in the sampling of celestial bodies, and their drilling behaviors directly affect the sampling results and drilling security. This paper introduces a lunar regolith coring bit (LRCB), which is a key component of sampling tools for lunar rock breaking during the lunar soil sampling process. We establish the interaction model between the drill bit and rock at a small cutting depth, and the two main influential parameters (forward and outward rake angles) of LRCB on drilling loads are determined. We perform the parameter screening task of LRCB with the aim to minimize the weight on bit (WOB). We verify the drilling load performances of LRCB after optimization, and the higher penetrations per revolution (PPR) are, the larger drilling loads we gained. Besides, we perform lunar soil drilling simulations to estimate the efficiency on chip conveying and sample coring of LRCB. The results of the simulation and test are basically consistent on coring efficiency, and the chip removal efficiency of LRCB is slightly lower than HIT-H bit from simulation. This work proposes a method for the design of coring bits in subsequent extraterrestrial explorations.
An Experimental Study of Fan Inflow Distortion Tone Noise

NASA Technical Reports Server (NTRS)

Koch, L. Danielle

2010-01-01

The tone noise generated when a fan ingests circumferentially distorted flow was studied by an experiment conducted with the Advanced Noise Control Fan at the NASA Glenn Research Center. The inflow was distorted by inserting cylindrical rods radially into the duct. The rods were arranged in circumferentially irregular patterns in three of the five configurations tested. Rods were held in place using a mounting ring with 30 equally spaced holes placed at an axial location one rotor chordlength upstream of the fan. Acoustic pressure was measured in the inlet and exhaust duct of the fan using the Rotating Rake fan tone measurement system. Sound power levels, calculated from the measured data, were plotted as a function of circumferential mode. An analytic description of the unsteady pressure distribution at the interaction plane between the stationary rods and the fan rotor is presented in a form suitable for representing the circumferentially irregularly placed rods. Terms in the analytical description for sound power were proven to be useful in determining the dominant circumferential modes measured in the experiment and the differences in mode power level between the configurations tested. Insight gained through this work will be useful in the development of tools to compute fan inflow distortion tone noise.
Framework for objective evaluation of privacy filters

NASA Astrophysics Data System (ADS)

Korshunov, Pavel; Melle, Andrea; Dugelay, Jean-Luc; Ebrahimi, Touradj

2013-09-01

Extensive adoption of video surveillance, affecting many aspects of our daily lives, alarms the public about the increasing invasion into personal privacy. To address these concerns, many tools have been proposed for protection of personal privacy in image and video. However, little is understood regarding the effectiveness of such tools and especially their impact on the underlying surveillance tasks, leading to a tradeoff between the preservation of privacy offered by these tools and the intelligibility of activities under video surveillance. In this paper, we investigate this privacy-intelligibility tradeoff objectively by proposing an objective framework for evaluation of privacy filters. We apply the proposed framework on a use case where privacy of people is protected by obscuring faces, assuming an automated video surveillance system. We used several popular privacy protection filters, such as blurring, pixelization, and masking and applied them with varying strengths to people's faces from different public datasets of video surveillance footage. Accuracy of face detection algorithm was used as a measure of intelligibility (a face should be detected to perform a surveillance task), and accuracy of face recognition algorithm as a measure of privacy (a specific person should not be identified). Under these conditions, after application of an ideal privacy protection tool, an obfuscated face would be visible as a face but would not be correctly identified by the recognition algorithm. The experiments demonstrate that, in general, an increase in strength of privacy filters under consideration leads to an increase in privacy (i.e., reduction in recognition accuracy) and to a decrease in intelligibility (i.e., reduction in detection accuracy). Masking also shows to be the most favorable filter across all tested datasets.
Surface deformation and friction characteristic of nano scratch at ductile-removal regime for optical glass BK7.

PubMed

Li, Chen; Zhang, Feihu; Ding, Ye; Liu, Lifei

2016-08-20

Nano scratch for optical glass BK7 based on the ductile-removal regime was carried out, and the influence rule of scratch parameters on surface deformation and friction characteristic was analyzed. Experimental results showed that, with increase of normal force, the deformation of burrs in the edge of the scratch was more obvious, and with increase of the scratch velocity, the deformation of micro-fracture and burrs in the edge of the scratch was more obvious similarly. The residual depth of the scratch was measured by atomic force microscope. The experimental results also showed that, with increase of normal force, the residual depth of the scratch increased linearly while the elastic recovery rate decreased. Furthermore, with increase of scratch velocity, the residual depth of the scratch decreased while the elastic recovery rate increased. The scratch process of the Berkovich indenter was divided into the cutting process of many large negative rake faces based on the improved cutting model, and the friction characteristic of the Berkovich indenter and the workpiece was analyzed. The analysis showed that the coefficient of friction increased and then tended to be stable with the increase of normal force. Meanwhile, the coefficient of friction decreased with the increase of scratch velocity, and the coefficients, k ln(v) and μ₀, were introduced to improve the original formula of friction coefficient.
Appropriation of a Representational Tool in a Second-Language Classroom

ERIC Educational Resources Information Center

Wen, Yun; Looi, Chee-Kit; Chen, Wenli

2015-01-01

While the affordances of face-to-face and online environments have been studied somewhat extensively, there is relatively less research on how technology-mediated learning takes place across multiple media in the networked classroom environment where face-to-face and online interactions are intertwined, especially in the context of language…

Extending Face-to-Face Interactions: Understanding and Developing an Online Teacher and Family Community

ERIC Educational Resources Information Center

Zhang, Chun; Du, Jianxia; Sun, Li; Ding, Yi

2018-01-01

Technology has been quickly changing human interactions, traditional practices, and almost every aspect of our lives. It is important to maintain effective face-to-face communication and interactions between teachers and families. Nonetheless, technology and its tools can also extend and enhance family-teacher relationships and partnerships. This…
Combined tool approach is 100% successful for emergency football face mask removal.

PubMed

Copeland, Aaron J; Decoster, Laura C; Swartz, Erik E; Gattie, Eric R; Gale, Stephanie D

2007-11-01

To compare effectiveness of two techniques for removing football face masks: cutting loop straps [cutting tool: FMXtractor (FMX)] or removing screws with a cordless screwdriver and using the FMXtractor as needed for failed removals [combined tool (CT)]. Null hypotheses: no differences in face mask removal success, removal time or difficulty between techniques or helmet characteristics. Retrospective, cross-sectional. NOCSAE-certified helmet reconditioning plants. 600 used high school helmets. Face mask removal attempted with two techniques. Success, removal time, rating of perceived exertion (RPE). Both techniques were effective [CT 100% (300/300); FMX 99.4% (298/300)]. Use of the backup FMXtractor in CT trials was required in 19% of trials. There was significantly (P<0.001) less call for the backup tool in helmets with silver screws (6%) than in helmets with other screws (31%). Mean removal time was 44.51+/-18.79s (CT: 37.84+/-15.37s, FMX: 51.21+/-19.54s; P<0.001). RPE was different between techniques (CT: 1.83+/-1.20, FMX: 3.11+/-1.27; P<0.001). Removal from helmets with silver screws was faster (Silver=33.38+/-11.03, Others=42.18+/-17.64; P<0.001) and easier (Silver=1.42+/-0.89, Other=2.23+/-1.33; P<0.001). CT was faster and easier than FMX. Most CT trials were completed with the screwdriver alone; helmets with silver screws had 94% screwdriver success. Clinically, these findings are important because this and other research shows that compared to removal with cutting tools, screwdriver removal decreases time, difficulty and helmet movement (reducing potential for iatrogenic injury). The combined-tool approach captures benefits of the screwdriver while offering a contingency for screw removal failure. Teams should use degradation-resistant screws. Sports medicine professionals must be prepared with appropriate tools and techniques to efficiently remove the face mask from an injured football player's helmet.
Recommender System and Web 2.0 Tools to Enhance a Blended Learning Model

ERIC Educational Resources Information Center

Hoic-Bozic, Natasa; Dlab, Martina Holenko; Mornar, Vedran

2016-01-01

Blended learning models that combine face-to-face and online learning are of great importance in modern higher education. However, their development should be in line with the recent changes in e-learning that emphasize a student-centered approach and use tools available on the Web to support the learning process. This paper presents research on…
Advanced CFD Methods for Hypervelocity Wind Tunnels

DTIC Science & Technology

2011-03-10

Mach 14 nozzle produces non-uniformities in the test section flow that are not desirable [1,2]. Calibration runs with Pitot pressure rakes suggest...flows is presented. The grid is based on the characteristic lines of the supersonic regions of the flow. This allows for grid alignment and clustering...novel grid generation scheme for hypersonic nozzle flows is presented. The grid is based on the characteristic lines of the supersonic regions of the
Astronaut John Young photographed collecting lunar samples

NASA Technical Reports Server (NTRS)

1972-01-01

Astronaut John W. Young, commander of the Apollo 16 lunar landing mission, is photographed collecting lunar samples near North Ray crater during the third Apollo 16 extravehicular activity (EVA-3) at the Descartes landing site. This picture was taken by Astronaut Charles M. Duke Jr., lunar module pilot. Young is using the lunar surface rake and a set of tongs. The Lunar Roving Vehicle is parked in the field of large boulders in the background.
Serpentine Diffuser Performance with Emphasis on Future Introduction to a Transonic Fan (Postprint)

DTIC Science & Technology

2013-01-01

conditioning barrel . The velocity distribution across the flow conditioning barrel was measured at the same axial location of inlet temperature and...rakes at the same axial plane (AIP) of the total pressure probe tips. The probes were constructed from stainless steel tubing with 0.027 inch inside...numbers with 195 axial and circumferential static pressure measurements within the diffuser flow path. Pressure distortion at the diffuser discharge
High-temperature, high-pressure bonding of nested tubular metallic components

DOEpatents

Quinby, T.C.

A tool is described for effecting high-temperature, high-compression bonding between the confronting faces of nested, tubular, metallic components. In a typical application, the tool is used to produce tubular target assemblies for irradiation in nuclear reactors or particle accelerators. The target assembly comprising a uranum foil and an aluninum-alloy substrate. The tool is composed of graphite. It comprises a tubular restraining member in which a mechanically expandable tubular core is mounted to form an annulus. The components to be bonded are mounted in nested relation in the annulus. The expandable core is formed of individually movable, axially elongated segments whose outer faces cooperatively define a cylindrical pressing surface and whose inner faces cooperatively define two opposed, inwardly tapered, axial bores. Tapered rams extend into the bores. The loaded tool is mounted in a conventional hot-press provided with evacuation means, heaters for maintaining its interior at bonding temperature, and hydraulic cylinders for maintaining a selected inwardly directed pressure on the tapered rams. With the hot-press evacuated and the loaded tool at the desired temperature, the cylinders are actuated to apply the selected pressure to the rams. The rams in turn expand the segmented core to maintain the nested components in compression against the restraining member. These conditions are maintained until the confronting faces of the nested components are joined in a continuous, uniform bond characterized by high thermal conductivity.
The Use of Internet-Based Social Media as a Tool in Enhancing Student's Learning Experiences in Biological Sciences

ERIC Educational Resources Information Center

Beltran-Cruz, Maribel; Cruz, Shannen Belle B.

2013-01-01

This study explored the use of social media as a tool in enhancing student's learning experiences, by using online instruction as a supplement to a face-to-face general education course, such as biological sciences. Survey data were collected from 186 students who were enrolled in a Biological Sciences course. The course was taught in a blended…
The Use of Technology as an Oral Achievement Testing Tool: Analysis of Students' Perceptions and Oral Performance in a Portuguese Language Program

ERIC Educational Resources Information Center

Santana-Paixao, Raquel C.

2017-01-01

Oral testing administration plays a significant role in foreign language programs aiming to foster the development of students' speaking abilities. With the development of language teaching software, the use of computer based recording tools are becoming increasingly used in language courses as an alternative to traditional face-to-face oral…
An Exploratory Study of the Use of Video as an Instructional Tool in an Introductory C# Programming Course

ERIC Educational Resources Information Center

Sharp, Jason H.; Schultz, Leah A.

2013-01-01

This study examines the background of introductory programming concepts and the use of video as an instructional tool. Thirty-five students in an introductory C# class were administered a survey to report data on demographics, usage on video, and opinions about the video. Students were in online and face to face sections of the class. Data were…
Learning Behaviours of Low-Achieving Children's Mathematics Learning in Using of Helping Tools in a Synchronous Peer-Tutoring System

ERIC Educational Resources Information Center

Tsuei, Mengping

2017-01-01

This study examined the effects of low-achieving children's use of helping tools in a synchronous mathematics peer-tutoring system on the children's mathematics learning and their learning behaviours. In a remedial class, 16 third-grade students in a remedial class engaged in peer tutoring in a face-to-face synchronous online environment during a…
Toward a Social Psychophysics of Face Communication.

PubMed

Jack, Rachael E; Schyns, Philippe G

2017-01-03

As a highly social species, humans are equipped with a powerful tool for social communication-the face. Although seemingly simple, the human face can elicit multiple social perceptions due to the rich variations of its movements, morphology, and complexion. Consequently, identifying precisely what face information elicits different social perceptions is a complex empirical challenge that has largely remained beyond the reach of traditional methods. In the past decade, the emerging field of social psychophysics has developed new methods to address this challenge, with the potential to transfer psychophysical laws of social perception to the digital economy via avatars and social robots. At this exciting juncture, it is timely to review these new methodological developments. In this article, we introduce and review the foundational methodological developments of social psychophysics, present work done in the past decade that has advanced understanding of the face as a tool for social communication, and discuss the major challenges that lie ahead.
The source parameters of 2013 Mw6.6 Lushan earthquake constrained with the restored local clipped seismic waveforms

NASA Astrophysics Data System (ADS)

Hao, J.; Zhang, J. H.; Yao, Z. X.

2017-12-01

We developed a method to restore the clipped seismic waveforms near epicenter using projection onto convex sets method (Zhang et al, 2016). This method was applied to rescue the local clipped waveforms of 2013 Mw 6.6 Lushan earthquake. We restored 88 out of 93 clipped waveforms of 38 broadband seismic stations of China Earthquake Networks (CEN). The epicenter distance of the nearest station to the epicenter that we can faithfully restore is only about 32 km. In order to investigate if the source parameters of earthquake could be determined exactly with the restored data, restored waveforms are utilized to get the mechanism of Lushan earthquake. We apply the generalized reflection-transmission coefficient matrix method to calculate the synthetic seismic records and simulated annealing method in inversion (Yao and Harkrider, 1983; Hao et al., 2012). We select 5 stations of CEN with the epicenter distance about 200km whose records aren't clipped and three-component velocity records are used. The result shows the strike, dip and rake angles of Lushan earthquake are 200o, 51o and 87o respectively, hereinafter "standard result". Then the clipped and restored seismic waveforms are applied respectively. The strike, dip and rake angles of clipped seismic waveforms are 184o, 53o and 72o respectively. The largest misfit of angle is 16o. In contrast, the strike, dip and rake angles of restored seismic waveforms are 198o, 51o and 87o respectively. It is very close to the "standard result". We also study the rupture history of Lushan earthquake constrained with the restored local broadband and teleseismic waves based on finite fault method (Hao et al., 2013). The result consists with that constrained with the strong motion and teleseismic waves (Hao et al., 2013), especially the location of the patch with larger slip. In real-time seismology, determining the source parameters as soon as possible is important. This method will help us to determine the mechanism of earthquake using the local clipped waveforms. Strong motion stations in China don't have good coverage at present. This method will help us to investigate the rupture history of large earthquake in China using the local clipped data of broadband stations.
Categorization for Faces and Tools-Two Classes of Objects Shaped by Different Experience-Differs in Processing Timing, Brain Areas Involved, and Repetition Effects.

PubMed

Kozunov, Vladimir; Nikolaeva, Anastasia; Stroganova, Tatiana A

2017-01-01

The brain mechanisms that integrate the separate features of sensory input into a meaningful percept depend upon the prior experience of interaction with the object and differ between categories of objects. Recent studies using representational similarity analysis (RSA) have characterized either the spatial patterns of brain activity for different categories of objects or described how category structure in neuronal representations emerges in time, but never simultaneously. Here we applied a novel, region-based, multivariate pattern classification approach in combination with RSA to magnetoencephalography data to extract activity associated with qualitatively distinct processing stages of visual perception. We asked participants to name what they see whilst viewing bitonal visual stimuli of two categories predominantly shaped by either value-dependent or sensorimotor experience, namely faces and tools, and meaningless images. We aimed to disambiguate the spatiotemporal patterns of brain activity between the meaningful categories and determine which differences in their processing were attributable to either perceptual categorization per se , or later-stage mentalizing-related processes. We have extracted three stages of cortical activity corresponding to low-level processing, category-specific feature binding, and supra-categorical processing. All face-specific spatiotemporal patterns were associated with bilateral activation of ventral occipito-temporal areas during the feature binding stage at 140-170 ms. The tool-specific activity was found both within the categorization stage and in a later period not thought to be associated with binding processes. The tool-specific binding-related activity was detected within a 210-220 ms window and was located to the intraparietal sulcus of the left hemisphere. Brain activity common for both meaningful categories started at 250 ms and included widely distributed assemblies within parietal, temporal, and prefrontal regions. Furthermore, we hypothesized and tested whether activity within face and tool-specific binding-related patterns would demonstrate oppositely acting effects following procedural perceptual learning. We found that activity in the ventral, face-specific network increased following the stimuli repetition. In contrast, tool processing in the dorsal network adapted by reducing its activity over the repetition period. Altogether, we have demonstrated that activity associated with visual processing of faces and tools during the categorization stage differ in processing timing, brain areas involved, and in their dynamics underlying stimuli learning.
Improving Students' Summary Writing Ability through Collaboration: A Comparison between Online Wiki Group and Conventional Face-To-Face Group

ERIC Educational Resources Information Center

Wichadee, Saovapa

2013-01-01

Wikis, as one of the Web 2.0 social networking tools, have been increasingly integrated into second language (L2) instruction to promote collaborative writing. The current study examined and compared summary writing abilities between students learning by wiki-based collaboration and students learning by traditional face-to-face collaboration.…
InterFace: A software package for face image warping, averaging, and principal components analysis.

PubMed

Kramer, Robin S S; Jenkins, Rob; Burton, A Mike

2017-12-01

We describe InterFace, a software package for research in face recognition. The package supports image warping, reshaping, averaging of multiple face images, and morphing between faces. It also supports principal components analysis (PCA) of face images, along with tools for exploring the "face space" produced by PCA. The package uses a simple graphical user interface, allowing users to perform these sophisticated image manipulations without any need for programming knowledge. The program is available for download in the form of an app, which requires that users also have access to the (freely available) MATLAB Runtime environment.
The development of a supportive care needs assessment tool for Indigenous people with cancer

PubMed Central

2012-01-01

Background Little is known about the supportive care needs of Indigenous people with cancer and to date, existing needs assessment tools have not considered cultural issues for this population. We aimed to adapt an existing supportive care needs assessment tool for use with Indigenous Australians with cancer. Methods Face-to-face interviews with Indigenous cancer patients (n = 29) and five focus groups with Indigenous key-informants (n = 23) were conducted to assess the face and content validity, cultural acceptability, utility and relevance of the Supportive Care Needs Survey - Short Form 34 (SCNS-SF34) for use with Indigenous patients with cancer. Results All items from the SCNS-SF34 were shortened and changed to use more appropriate language (e.g. the word 'anxiety' was substituted with 'worry'). Seven questions were omitted (e.g. items on death and future considerations) as they were deemed culturally inappropriate or irrelevant and 12 items were added (e.g. accessible transport). Optional instructions were added before the sexual items. The design and response format of the SCNS-SF34 was modified to make it easier to use for Indigenous cancer patients. Given the extensive modifications to the SCNS-SF34 and the liklihood of a different factor structure we consider this tool to be a new tool rather than a modification. The Supportive care needs assessment tool for Indigenous people (SCNAT-IP) shows promising face and content validity and will be useful in informing services where they need to direct their attention for these patients. Conclusions Indigenous people with cancer have language, customs and specific needs that are not accommodated within the standard SCNS-SF34. Our SCNAT-IP improves acceptability, relevance and face validity for Indigenous-specific concerns. Our SCNAT-IP will allow screening for supportive care needs that are specific to Indigenous cancer patients' and greatly inform targeted policy development and practice. PMID:22817614
Analytical, Numerical, and Experimental Results on Turbulent Boundary Layers

DTIC Science & Technology

1976-07-01

a pitot pressure rake where the spacing between probe centers was 0.5 in. near the wall and 1.0 in. away from the wall. Recently, measurements have...Pressure Gradient, Part II. Analysis- of the Experimental Data." BRL R 1543, June 1971. 51. Allen, J. M. " Pitot -Probe Displacement in a Supersonic Turbulent...numbers; (4) a description of the data reduction of pitot pressure measurements utilizing these analytical results in order to obtain velocity
Open-Water Resistance and Seakeeping Characteristics of Ships with Icebreaking Bows

DTIC Science & Technology

1991-05-13

of a Knuckled Forefoot on a Typical Icebreaker ...... ................... . 19 3-2. Lines Plan, T-AGS OCEAN (ICE) . * * .... . 23 3-3. Curve of...the ice. As the stem strikes the ice, initial failure of the ice occurs by simple crushing. Then the raked stem of the icebreaker rides up onto the ice...bossings, skegs, rudders, 18 and special stem forefoot shapes were not included in the shapes tested. To ensure that the parent and its variants
Change of magnetic domain structure by mechanically induced twin boundary motion in Ni-Mn-Ga single crystal

NASA Astrophysics Data System (ADS)

Kopecký, Vít; Heczko, Oleg

2017-10-01

The single variant state exhibits usual labyrinth and band magnetic domains depending on orientation of easy magnetization axis. By the passage of single twin boundary induced by mechanical stress the rake and granular domain patterns are formed. These domain patterns are further modified by repeated passage of the twin boundary resulting in similar domain patterns in the sample even though the orientation of the magnetization is different.

In-flight leading-edge extension vortex flow-field survey measurements on a F-18 aircraft at high angle of attack

NASA Technical Reports Server (NTRS)

Richwine, David M.; Fisher, David F.

1992-01-01

Flow-field measurements on the leading-edge extension (LEX) of the F-18 High Alpha Research Vehicle (HARV) were obtained using a rotating rake with 16 hemispherical-tipped five-hole probes. Detailed pressure, velocity, and flow direction data were obtained through the LEX vortex core. Data were gathered during 1-g quasi-stabilized flight conditions at angles of attack alpha from 10 degrees to 52 degrees and at Reynolds numbers based on mean aerodynamic cord up to 16 x 10(exp 6). Normalized dynamic pressures and crossflow velocities clearly showed the primary vortex above the LEX and formation of a secondary vortex at higher angles of attack. The vortex was characterized by a ring of high dynamic pressure surrounding a region of low dynamic pressure at the vortex core center. The vortex core, subcore diameter, and vertical location of the core above the LEX increased with angle of attack. Minimum values for static pressure were obtained in the vortex subcore and decreased nearly linearly with increasing angle of attack until vortex breakdown. Rake-measured static pressures were consistent with previously documented surface pressures and showed good agreement with flow visualization flight test results. Comparison of the LEX vortex flight test data to computational solutions at alpha approximately equals 19 degrees and 30 degrees showed fair correlation.
Accounting for Fault Roughness in Pseudo-Dynamic Ground-Motion Simulations

NASA Astrophysics Data System (ADS)

Mai, P. Martin; Galis, Martin; Thingbaijam, Kiran K. S.; Vyas, Jagdish C.; Dunham, Eric M.

2017-09-01

Geological faults comprise large-scale segmentation and small-scale roughness. These multi-scale geometrical complexities determine the dynamics of the earthquake rupture process, and therefore affect the radiated seismic wavefield. In this study, we examine how different parameterizations of fault roughness lead to variability in the rupture evolution and the resulting near-fault ground motions. Rupture incoherence naturally induced by fault roughness generates high-frequency radiation that follows an ω-2 decay in displacement amplitude spectra. Because dynamic rupture simulations are computationally expensive, we test several kinematic source approximations designed to emulate the observed dynamic behavior. When simplifying the rough-fault geometry, we find that perturbations in local moment tensor orientation are important, while perturbations in local source location are not. Thus, a planar fault can be assumed if the local strike, dip, and rake are maintained. We observe that dynamic rake angle variations are anti-correlated with the local dip angles. Testing two parameterizations of dynamically consistent Yoffe-type source-time function, we show that the seismic wavefield of the approximated kinematic ruptures well reproduces the radiated seismic waves of the complete dynamic source process. This finding opens a new avenue for an improved pseudo-dynamic source characterization that captures the effects of fault roughness on earthquake rupture evolution. By including also the correlations between kinematic source parameters, we outline a new pseudo-dynamic rupture modeling approach for broadband ground-motion simulation.
In-Flight Capability for Evaluating Skin-Friction Gages and Other Near-Wall Flow Sensors

NASA Technical Reports Server (NTRS)

Bui, Trong T.; Pipitone, Brett J.; Krake, Keith L.; Richwine, Dave (Technical Monitor)

2003-01-01

An 8-in.-square boundary-layer sensor panel has been developed for in-flight evaluation of skin-friction gages and other near-wall flow sensors on the NASA Dryden Flight Research Center F-15B/Flight Test Fixture (FTF). Instrumentation on the sensor panel includes a boundary-layer rake, temperature sensors, static pressure taps, and a Preston tube. Space is also available for skin-friction gages or other near-wall flow sensors. Pretest analysis of previous F-15B/FTF flight data has identified flight conditions suitable for evaluating skin-friction gages. At subsonic Mach numbers, the boundary layer over the sensor panel closely approximates the two-dimensional (2D), law-of-the-wall turbulent boundary layer, and skin-friction estimates from the Preston tube and the rake (using the Clauser plot method) can be used to evaluate skin-friction gages. At supersonic Mach numbers, the boundary layer over the sensor panel becomes complex, and other means of measuring skin friction are needed to evaluate the accuracy of new skin-friction gages. Results from the flight test of a new rubber-damped skin-friction gage confirm that at subsonic Mach numbers, nearly 2D, law-of-the-wall turbulent boundary layers exist over the sensor panel. Sensor panel data also show that this new skin-friction gage prototype does not work in flight.
High-temperature, high-pressure bonding of nested tubular metallic components

DOEpatents

Quinby, Thomas C.

1980-01-01

This invention is a tool for effecting high-temperature, high-compression bonding between the confronting faces of nested, tubular, metallic components. In a typical application, the tool is used to produce tubular target assemblies for irradiation in nuclear reactors or particle accelerators, the target assembly comprising a uranium foil and an aluminum-alloy substrate. The tool preferably is composed throughout of graphite. It comprises a tubular restraining member in which a mechanically expandable tubular core is mounted to form an annulus with the member. The components to be bonded are mounted in nested relation in the annulus. The expandable core is formed of individually movable, axially elongated segments whose outer faces cooperatively define a cylindrical pressing surface and whose inner faces cooperatively define two opposed, inwardly tapered, axial bores. Tapered rams extend respectively into the bores. The loaded tool is mounted in a conventional hot-press provided with evacuation means, heaters for maintaining its interior at bonding temperature, and hydraulic cylinders for maintaining a selected inwardly directed pressure on the tapered rams. With the hot-press evacuated and the loaded tool at the desired temperature, the cylinders are actuated to apply the selected pressure to the rams. The rams in turn expand the segmented core to maintain the nested components in compression against the restraining member. These conditions are maintained until the confronting faces of the nested components are joined in a continuous, uniform bond characterized by high thermal conductivity.
Family medicine practice performance and knowledge management.

PubMed

Orzano, A John; McInerney, Claire R; Tallia, Alfred F; Scharf, Davida; Crabtree, Benjamin F

2008-01-01

Knowledge management (KM) is the process by which people in organizations find, share, and develop knowledge for action. KM affects performance by influencing work relationships to enhance learning and decision making. To identify how family medicine practices exhibit KM. A model and a template of KM concepts were derived from a comprehensive organizational literature review. Two higher and two lower performing family medicine practices were purposefully selected from existing comparative case studies based on prevention delivery rates and innovation. Interviews, fieldnotes of operations, and clinical encounters were coded independently using the template. Face-to-face discussions resolved coding differences. All practices had processes and tools for finding, sharing, and developing knowledge; however, KM overall was limited despite implementation of expensive technologies like an electronic medical record. Where present, KM processes and tools were used by individuals but not integrated throughout the organization. Loss of information was prominent, and finding knowledge was underdeveloped. The use of technical tools and developing knowledge by reconfiguration and measurement were particularly limited. Socially related tools, such as face-to-face-communication for sharing and developing knowledge, were more developed. As in other organizations, tool use was tailored for specific outcomes and leveraged by other organizational capacities. Differences in KM occur within family practices and between family practices and other organizations and may have implications for improving practice performance. Understanding interaction patterns of work relationships and KM may explain why costly technical or externally imposed "one size fits all" practice organizational interventions have had mixed results and limited sustainability.
Judgment skills, a missing component in health literacy: development of a tool for asthma patients in the Italian-speaking region of Switzerland.

PubMed

Moreno Londoño, Ana Maria; Schulz, Peter J

2014-04-01

Health literacy has been recognized as an important factor influencing health behaviors and health outcomes. However, its definition is still evolving, and the tools available for its measurement are limited in scope. Based on the conceptualization of health literacy within the Health Empowerment Model, the present study developed and validated a tool to assess patient's health knowledge use, within the context of asthma self-management. A review of scientific literature on asthma self-management, and several interviews with pulmonologists and asthma patients were conducted. From these, 19 scenarios with 4 response options each were drafted and assembled in a scenario-based questionnaire. Furthermore, a three round Delphi procedure was carried out, to validate the tool with the participation of 12 specialists in lung diseases. The face and content validity of the tool were achieved by face-to-face interviews with 2 pulmonologists and 5 patients. Consensus among the specialists on the adequacy of the response options was achieved after the three round Delphi procedure. The final tool has a 0.97 intra-class correlation coefficient (ICC), indicating a strong level of agreement among experts on the ratings of the response options. The ICC for single scenarios, range from 0.92 to 0.99. The newly developed tool provides a final score representing patient's health knowledge use, based on the specialist's consensus. This tool contributes to enriching the measurement of a more advanced health literacy dimension.
Automated facial attendance logger for students

NASA Astrophysics Data System (ADS)

Krithika, L. B.; Kshitish, S.; Kishore, M. R.

2017-11-01

From the past two decades, various spheres of activity are in the aspect of ‘Face recognition’ as an essential tool. The complete series of actions of face recognition is composed of 3 stages: Face Detection, Feature Extraction and Recognition. In this paper, we make an effort to put forth a new application of face recognition and detection in education. The proposed system scans the classroom and detects the face of the students in class and matches the scanned face with the templates that is available in the database and updates the attendance of the respective students.
Search Engines for Tomorrow's Scholars

ERIC Educational Resources Information Center

Fagan, Jody Condit

2011-01-01

Today's scholars face an outstanding array of choices when choosing search tools: Google Scholar, discipline-specific abstracts and index databases, library discovery tools, and more recently, Microsoft's re-launch of their academic search tool, now dubbed Microsoft Academic Search. What are these tools' strengths for the emerging needs of…
Emerging Instructional Technologies: Exploring the Extent of Faculty Use of Web 2.0 Tools at a Midwestern Community College

ERIC Educational Resources Information Center

Daher, Tareq; Lazarevic, Bojan

2014-01-01

The purpose of this research is to provide insight into the several aspects of instructional use of emerging web-based technologies. The study first explores the extent of Web 2.0 technology integration into face-to-face classroom activities. In this phase, the main focus of research interests was on the types and dynamics of Web 2.0 tools used by…
Low Energy Consumption Hydraulic Techniques

DTIC Science & Technology

1988-08-30

usually at welds . 1-15 SECTION II PHASE I - ADVANCED AIRCRAFT HYDRAULIC SYSTEM SELECTION Phase I included Task 1 selection of the aircraft and definition...face was bronze plated. The bearings were 52100 tool steel and the pistons were M50 tool steel. The shoe faces were 4140 with bronze plate and the back...o Magnet assembly o Coil assembly DDV Force Motor - -- ,..._(First Stage) oeMain Control Valve __(Second Sae Main Control Valve LVDT Figure 282 Direct
Evaluating Standards-Based Assessment Rubrics in a Postgraduate Public Health Subject

ERIC Educational Resources Information Center

Kite, James; Phongsavan, Philayrath

2017-01-01

Standards-based assessment rubrics are recognised as an important tool for ensuring clear criteria in higher education. Most of the available evidence on rubrics comes from studies with face-to-face undergraduate students. Our study evaluated the introduction of rubrics into a postgraduate subject that included both online and face-to-face…
The Hybrid Advantage: Graduate Student Perspectives of Hybrid Education Courses

ERIC Educational Resources Information Center

Hall, Sarah; Villareal, Donna

2015-01-01

Hybrid courses combine online and face-to-face learning environments. To organize and teach hybrid courses, instructors must understand the uses of multiple online learning tools and face-toface classroom activities to promote and monitor the progress of students. The purpose of this phenomenological study was to explore the perspectives of…
Neural Computation as a Tool to Differentiate Perceptual from Emotional Processes: The Case of Anger Superiority Effect

ERIC Educational Resources Information Center

Mermillod, Martial; Vermeulen, Nicolas; Lundqvist, Daniel; Niedenthal, Paula M.

2009-01-01

Research findings in social and cognitive psychology imply that it is easier to detect angry faces than happy faces in a crowd of neutral faces [Hansen, C. H., & Hansen, R. D. (1988). Finding the face in the crowd--An anger superiority effect. "Journal of Personality and Social Psychology," 54(6), 917-924]. This phenomenon has been held to have…
Comparison of Three Biomass Sampling Techniques on Submersed Aquatic Plants in a Northern Tier Lake

DTIC Science & Technology

2010-07-01

distribution in 3 out of 14 species when comparing the box-core sampler and the rake method. These included forked duckweed (Lemna trisulca L, p...each site did not exhibit differences. These included coontail (p=0.2949), muskgrass (p=0.2746), American elodea (p=0.7622), forked duckweed (p...collected by the PVC-core sampler. These included coontail (p=0.000), chara (p=0.0219), American elodea (p=0.0061), forked duckweed (p=0.0000), najas (p
Measurements in Regions of Shock Wave/Turbulent Boundary Layer Interaction from Mach 3 to 10 for Open and Blind Code Evaluation/Validation

DTIC Science & Technology

2013-03-01

rakes containing pitot pressure probes, stagnation heat transfer gauges on hemispherical cylinders, total temperature measurements with vented...defined configurations in both “true temperature” and “cold” supersonic and hypersonic flows with boundary and flow conditions to provide the basis for...conducted over the past 50 years to provide data on both wedge- and shock- induced turbulent separated regions in supersonic and hypersonic flows suffer from
Pre-Flight Ground Testing of the Full-Scale HIFiRE-1 Vehicle at Fully Duplicated Flight Conditions: Part 2

DTIC Science & Technology

2008-05-14

survey rake installed in the test section to measure pitot pressure, static pressure and stagnation point heat transfer in the freestream. From these...on the cone, employing time of arrival pressure transducers to obtain 2"d mode transition frequencies, and making pitot pressure measurements to...these studies have proven to be the most accurate measurement technique in supersonic and hypersonic test facilities, and the small size of the sensing
Wind Tunnel Results from a Nozzle Afterbody Test of A 0.1-Scale Fighter Aircraft in the Mach Number Regime of 0.6 to 1.6

DTIC Science & Technology

1978-06-01

25 4. Nose Strake and Pitot Boom Details . . . . . . . . . . . . . . . . . . . . . . 28 5. Exhaust Nozzle Closure...actual wing through the use of simulated wing gloves (Fig. 3c) which duplicated the modification required on the wingtip supported model. The pitot ...pressure rakes located in the model plenum upstream of the nozzle throat were used to monitor the simulated jet flow. 2.2.5 Surface Pressures
Evaluation of a Wedge on a Force Balance as a Flow Angle Probe

DTIC Science & Technology

1975-02-01

pitot rake attached to the Captive Trajectory System (CTS), and (3) measurement of flow angles in the same region with a probe attached to the CTS...localized pressures. Although it was the characteristics of supersonic flow which led to this conclusion, and even though the wedge design was based...vary the open area from near zero to 10 percent. Suction through the porous walls is used to maximize flow uniformity and to develop supersonic flow
The Exoplanet Characterization ToolKit (ExoCTK)

NASA Astrophysics Data System (ADS)

Stevenson, Kevin; Fowler, Julia; Lewis, Nikole K.; Fraine, Jonathan; Pueyo, Laurent; Valenti, Jeff; Bruno, Giovanni; Filippazzo, Joseph; Hill, Matthew; Batalha, Natasha E.; Bushra, Rafia

2018-01-01

The success of exoplanet characterization depends critically on a patchwork of analysis tools and spectroscopic libraries that currently require extensive development and lack a centralized support system. Due to the complexity of spectroscopic analyses and initial time commitment required to become productive, there are currently a limited number of teams that are actively advancing the field. New teams with significant expertise, but without the proper tools, face prohibitively steep hills to climb before they can contribute. As a solution, we are developing an open-source, modular data analysis package in Python and a publicly facing web interface focused primarily on atmospheric characterization of exoplanets and exoplanet transit observation planning with JWST. The foundation of these software tools and libraries exist within pockets of the exoplanet community. Our project will gather these seedling tools and grow a robust, uniform, and well maintained exoplanet characterization toolkit.
Categorization for Faces and Tools—Two Classes of Objects Shaped by Different Experience—Differs in Processing Timing, Brain Areas Involved, and Repetition Effects

PubMed Central

Kozunov, Vladimir; Nikolaeva, Anastasia; Stroganova, Tatiana A.

2018-01-01

The brain mechanisms that integrate the separate features of sensory input into a meaningful percept depend upon the prior experience of interaction with the object and differ between categories of objects. Recent studies using representational similarity analysis (RSA) have characterized either the spatial patterns of brain activity for different categories of objects or described how category structure in neuronal representations emerges in time, but never simultaneously. Here we applied a novel, region-based, multivariate pattern classification approach in combination with RSA to magnetoencephalography data to extract activity associated with qualitatively distinct processing stages of visual perception. We asked participants to name what they see whilst viewing bitonal visual stimuli of two categories predominantly shaped by either value-dependent or sensorimotor experience, namely faces and tools, and meaningless images. We aimed to disambiguate the spatiotemporal patterns of brain activity between the meaningful categories and determine which differences in their processing were attributable to either perceptual categorization per se, or later-stage mentalizing-related processes. We have extracted three stages of cortical activity corresponding to low-level processing, category-specific feature binding, and supra-categorical processing. All face-specific spatiotemporal patterns were associated with bilateral activation of ventral occipito-temporal areas during the feature binding stage at 140–170 ms. The tool-specific activity was found both within the categorization stage and in a later period not thought to be associated with binding processes. The tool-specific binding-related activity was detected within a 210–220 ms window and was located to the intraparietal sulcus of the left hemisphere. Brain activity common for both meaningful categories started at 250 ms and included widely distributed assemblies within parietal, temporal, and prefrontal regions. Furthermore, we hypothesized and tested whether activity within face and tool-specific binding-related patterns would demonstrate oppositely acting effects following procedural perceptual learning. We found that activity in the ventral, face-specific network increased following the stimuli repetition. In contrast, tool processing in the dorsal network adapted by reducing its activity over the repetition period. Altogether, we have demonstrated that activity associated with visual processing of faces and tools during the categorization stage differ in processing timing, brain areas involved, and in their dynamics underlying stimuli learning. PMID:29379426

Wake Measurement Downstream of a Hybrid Wing Body Model with Blown Flaps

NASA Technical Reports Server (NTRS)

Lin, John C.; Jones, Gregory S.; Allan, Brian G.; Westra, Bryan W.; Collins, Scott W.; Zeune, Cale H.

2010-01-01

Flow-field measurements were obtained in the wake of a full-span Hybrid Wing Body model with internally blown flaps. The test was performed at the NASA Langley 14 x 22 Foot Subsonic Tunnel at low speeds. Off-body measurements were obtained with a 7-hole probe rake survey system. Three model configurations were investigated. At 0deg angle of attack the surveys were completed with 0deg and 60deg flap deflections. At 10deg angle of attack the wake surveys were completed with a slat and a 60deg flap deflection. The 7-hole probe results further quantified two known swirling regions (downstream of the outboard flap edge and the inboard/outboard flap juncture) for the 60deg flap cases with blowing. Flowfield results and the general trends are very similar for the two blowing cases at nozzle pressure ratios of 1.37 and 1.56. High downwash velocities correlated with the enhanced lift for the 60deg flap cases with blowing. Jet-induced effects are the largest at the most inboard station for all (three) velocity components due in part to the larger inboard slot height. The experimental data are being used to improve computational tools for high-lift wings with integrated powered-lift technologies.
Predicted and Measured Modal Sound Power Levels for a Fan Ingesting Distorted Inflow

NASA Technical Reports Server (NTRS)

Koch, L. Danielle

2010-01-01

Refinements have been made to a method for estimating the modal sound power levels of a ducted fan ingesting distorted inflow. By assuming that each propagating circumferential mode consists only of a single radial mode (the one with the highest cut-off ratio), circumferential mode sound power levels can be computed for a variety of inflow distortion patterns and operating speeds. Predictions from the refined theory have been compared to data from an experiment conducted in the Advanced Noise Control Fan at NASA Glenn Research Center. The inflow to the fan was distorted by inserting cylindrical rods radially into the inlet duct. The rods were placed at an axial location one rotor chord length upstream of the fan and arranged in both regular and irregular circumferential patterns. The fan was operated at 2000, 1800, and 1400 rpm. Acoustic pressure levels were measured in the fan inlet and exhaust ducts using the Rotating Rake fan mode measurement system. Far field sound pressure levels were also measured. It is shown that predicted trends in circumferential mode sound power levels closely match the experimental data for all operating speeds and distortion configurations tested. Insight gained through this work is being used to develop more advanced tools for predicting fan inflow distortion tone noise levels.
Effectiveness of integrating case studies in online and face-to-face instruction of pathophysiology: a comparative study.

PubMed

Saleh, Suha M; Asi, Yara M; Hamed, Kastro M

2013-06-01

Due to growing demand from students and facilitated by innovations in educational technology, institutions of higher learning are increasingly offering online courses. Subjects in the hard sciences, such as pathophysiology, have traditionally been taught in the face-to-face format, but growing demand for preclinical science courses has compelled educators to incorporate online components into their classes to promote comprehension. Learning tools such as case studies are being integrated into such courses to aid in student interaction, engagement, and critical thinking skills. Careful assessment of pedagogical techniques is essential; hence, this study aimed to evaluate and compare student perceptions of the use of case studies in face-to-face and fully online pathophysiology classes. A series of case studies was incorporated into the curriculum of a pathophysiology class for both class modes (online and face to face). At the end of the semester, students filled out a survey assessing the effectiveness of the case studies. Both groups offered positive responses about the incorporation of case studies in the curriculum of the pathophysiology class. This study supports the argument that with proper use of innovative teaching tools, such as case studies, online pathophysiology classes can foster a sense of community and interaction that is typically only seen with face-to-face classes, based on student responses. Students also indicated that regardless of class teaching modality, use of case studies facilitates student learning and comprehension as well as prepares them for their future careers in health fields.
Design and usability of heuristic-based deliberation tools for women facing amniocentesis.

PubMed

Durand, Marie-Anne; Wegwarth, Odette; Boivin, Jacky; Elwyn, Glyn

2012-03-01

Evidence suggests that in decision contexts characterized by uncertainty and time constraints (e.g. health-care decisions), fast and frugal decision-making strategies (heuristics) may perform better than complex rules of reasoning. To examine whether it is possible to design deliberation components in decision support interventions using simple models (fast and frugal heuristics). The 'Take The Best' heuristic (i.e. selection of a 'most important reason') and 'The Tallying' integration algorithm (i.e. unitary weighing of pros and cons) were used to develop two deliberation components embedded in a Web-based decision support intervention for women facing amniocentesis testing. Ten researchers (recruited from 15), nine health-care providers (recruited from 28) and ten pregnant women (recruited from 14) who had recently been offered amniocentesis testing appraised evolving versions of 'your most important reason' (Take The Best) and 'weighing it up' (Tallying). Most researchers found the tools useful in facilitating decision making although emphasized the need for simple instructions and clear layouts. Health-care providers however expressed concerns regarding the usability and clarity of the tools. By contrast, 7 out of 10 pregnant women found the tools useful in weighing up the pros and cons of each option, helpful in structuring and clarifying their thoughts and visualizing their decision efforts. Several pregnant women felt that 'weighing it up' and 'your most important reason' were not appropriate when facing such a difficult and emotional decision. Theoretical approaches based on fast and frugal heuristics can be used to develop deliberation tools that provide helpful support to patients facing real-world decisions about amniocentesis. © 2011 Blackwell Publishing Ltd.
Use of a Social Question Answering Application in a Face-to-Face College Biology Class

ERIC Educational Resources Information Center

Grasso, SandraJean M.

2017-01-01

University students use social media tools not only to connect with friends socially but also to collaborate with classmates. Many universities have embraced academically-focused social media platforms such as social question answering (SQA) applications to make student interactions easier. This study addresses how students in a face-to-face…
Development and validation of the health literacy assessment tool for older people in Taiwan: potential impacts of cultural differences.

PubMed

Chung, Min-Huey; Chen, Liang-Kung; Peng, Li-Ning; Chi, Mei-Ju

2015-01-01

To screen health literacy among urban elderly in Taiwan, who cannot be evaluated easily using the current measurement tools because of the "face", which meant someone felt embarrassed if he did not know how to do something. A literature review was performed to define a framework for developing the health literacy screening tool. Two hundred elderly were recruited to test the validity and reliability for pilot study. One thousand and eighty two elderly who came from quota sampling in Taipei City by administrative areas and gender were interviewed face-to-face to gather health literacy performance by the developed health literacy screening tool and the short-form Mandarin Health Literacy Scale (s-MHLS). 10-items of health literacy screening tool by self-perception were developed. The mean score of screening tool among analysis sample was 42.3 (0-50) and s-MHLS was 9.5 (0-11). Pearson correlation coefficient was 0.441 (p<0.0001) between these two measurements. Multiple regressions showed that, female, younger, higher education, living with family, has no primary caregiver, has few medical companionship, and higher score of health knowledge had better health literacy performance in both measurements. This screening tool should be applied to screen health literacy of elderly came from baby boomer who usually have lower education levels than the general population in Chinese regions. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.
A review of Integrated Vehicle Health Management tools for legacy platforms: Challenges and opportunities

NASA Astrophysics Data System (ADS)

Esperon-Miguez, Manuel; John, Philip; Jennions, Ian K.

2013-01-01

Integrated Vehicle Health Management (IVHM) comprises a set of tools, technologies and techniques for automated detection, diagnosis and prognosis of faults in order to support platforms more efficiently. Specific challenges are faced when IVHM tools are to be retrofitted into legacy vehicles since major modifications are much more challenging than with platforms whose design can still be modified. The topics covered in this Review Paper include the state of the art of IVHM tools and how their characteristics match the requirements of legacy aircraft, a summary of problems faced in the past trying to retrofit IVHM tools both from a technical and organisational perspective and the current level of implementation of IVHM in industry. Although the technology has not reached the level necessary to implement IVHM to its full potential on every kind of component, significant progress has been achieved on rotating equipment, structures or electronics. Attempts to retrofit some of these tools in the past faced both technical difficulties and opposition by some stakeholders, the later being responsible for the failure of technically sound projects in more than one occasion. Nevertheless, despite these difficulties, products and services based on IVHM technology have started to be offered by the manufacturers and, what is more important, demanded by the operators, providing guidance on what the industry would demand from IVHM on legacy aircraft.
FaceIt: face recognition from static and live video for law enforcement

NASA Astrophysics Data System (ADS)

Atick, Joseph J.; Griffin, Paul M.; Redlich, A. N.

1997-01-01

Recent advances in image and pattern recognition technology- -especially face recognition--are leading to the development of a new generation of information systems of great value to the law enforcement community. With these systems it is now possible to pool and manage vast amounts of biometric intelligence such as face and finger print records and conduct computerized searches on them. We review one of the enabling technologies underlying these systems: the FaceIt face recognition engine; and discuss three applications that illustrate its benefits as a problem-solving technology and an efficient and cost effective investigative tool.
Composite sandwich structure and method for making same

NASA Technical Reports Server (NTRS)

Magurany, Charles J. (Inventor)

1995-01-01

A core for a sandwich structure which has multi-ply laminate ribs separated by voids is made as an integral unit in one single curing step. Tooling blocks corresponding to the voids are first wrapped by strips of prepreg layup equal to one half of each rib laminate so a continuous wall of prepreg material is formed around the tooling blocks. The wrapped tooling blocks are next pressed together laterally, like tiles, so adjoining walls from two tooling blocks are joined. The assembly is then cured by conventional methods, and afterwards the tooling blocks are removed so voids are formed. The ribs can be provided with integral tabs forming bonding areas for face sheets, and face sheets may be co-cured with the core ribs. The new core design is suitable for discrete ribcores used in space telescopes and reflector panels, where quasiisotropic properties and zero coefficient of thermal expansion are required.
Understanding Surgical Resident and Fellow Perspectives on Their Operative Performance Feedback Needs: A Qualitative Study.

PubMed

Bello, Ricardo J; Sarmiento, Samuel; Meyer, Meredith L; Rosson, Gedge D; Cooney, Damon S; Lifchez, Scott D; Cooney, Carisa M

2018-04-20

Operative performance feedback is essential for surgical training. We aimed to understand surgical trainees' views on their operative performance feedback needs and to characterize feedback to elucidate factors affecting its value from the resident perspective. Using a qualitative research approach, 2 research fellows conducted semistructured, one-on-one interviews with surgical trainees. We analyzed recurring themes generated during interviews related to feedback characteristics, as well as the extent to which performance rating tools can help meet trainees' operative feedback needs. Departments or divisions of general or plastic surgery at 9 US academic institutions. Surgical residents and clinical fellows in general or plastic surgery. We conducted 30 interviews with 9 junior residents, 14 senior residents, and 7 clinical fellows. Eighteen (60%) participants were in plastic and 12 (40%) were in general surgery. Twenty-four participants (80%) reported feedback as very or extremely important during surgical training. All trainees stated that verbal, face-to-face feedback is the most valuable, especially if occurring during (92%) or immediately after (65%) cases. Of those trainees using performance rating tools (74%), most (57%) expressed positive views about them but wanted the tools to complement and not replace verbal feedback in surgical education. Trainees value feedback more if received within 1 week or the case. Verbal, face-to-face feedback is very or extremely important to surgical trainees. Residents and fellows prefer to receive feedback during or immediately after a case and continue to value feedback if received within 1 week of the event. Performance rating tools can be useful for providing formative feedback and documentation but should not replace verbal, face-to-face feedback. Considering trainee views on feedback may help reduce perceived gaps in feedback demand-versus-supply in surgical training, which may be essential to overcoming current challenges in surgical education. Copyright © 2018 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.
Diagnostic developments for velocity and temperature measurements in uni-element rocket environments

NASA Astrophysics Data System (ADS)

Philippart, Kenneth D.

1995-08-01

Velocity and temperature measurements were taken within a uni-element rocket combustion chamber for hydrogen-oxygen propellants using laser Doppler velocimetry, thermocouples, and a thermocouple-based temperature rake developed for this effort. Velocity and turbulence profiles were obtained for firings with a gaseous oxygen (GO2)/gaseous hydrogen (GH2) coaxial shear injector at axial locations of 1.6 mm (0.063 in.), 6.4 mm (0.25 in.), 12.7 mm (0.5 in.), 25.4 mm (1 in.) and 50.8 mm (2 in.). Aluminum oxide particles of various sizes seeded the flow in an attempt to explain the discrepancies. While cold-flow simulations were promising, hot-fire results for the various particles were virtually identical and still lower than earlier data. The hot-firings were self-consistent and question the reproducibility of the previous data. Velocity measurements were made closer to the injector than the preceding work. Asymmetries were noted in all profiles. The shear layer displayed high turbulence levels. The central flow near the injector resembled turbulent pipe flow. Recirculation zones existed at the chamber walls and became smaller as the flow evolved downstream. The combusting flow region expanded with increasing axial distance. A thermocouple-instrumented coaxial injector was fired with GO2/GH2 propellants. The injector exit plane boundary conditions were determined. The feasibility of a thermocouple-based temperature rake was established. Tests at three axial positions for air/GM2 firings revealed asymmetric profiles. Temperatures increased with increasing axial distance.
Macrophyte monitoring along the Trentino side of the Lake Garda

NASA Astrophysics Data System (ADS)

Pellegrini, Giovanna; Monauni, Catia; Fedrizzi, Fabio; Laura, Fravezzi; Paola, Testa; Silvia, Costaraoss; Mario, Mazzurana; Gaetano, Patti; Barbara, Zennaro

2013-04-01

Macrophytes, that grow along the Trentino shorezone of the Lake Garda, were sampled and mapped during summer 2010. The sampling protocol foresees a lake bottom survey until the depth of 15 using GPS system, for identifying sampling sites and transects, waterproof camcorder, batiscope and a rake. The proof of 13/14 meters is the internal limit for macrophyte development. The area between 6 and 13/14 meters was surveyed with a robot camcorder placed on a boat of the fireworks brigade of Trento. This boat was used to track the 14 km of the shorezone of the Trentino part of the Lake Garda. The investigation result is a survey of a wide carex prairie that has no interruption all along the lake perimeter. An inflatable boat was used to inspect the shorezone using a batiscope. The macrophyte samples were collected using a rake. The number of mapped sites is 15, transects are 15 and identified 18 different species. During 2011, in conjunction with the flight MIVIS within the EULAKES project, the macrophyte distribution was confirmed and further inspection was carried out for sampling and classifying caracee. Among the species collected, Chara globularis was present in all sites sampled, while sites 0 and 12, corresponding respectively to local reserve Val Gola and the bay of Torbole, showed the highest biodiversity among sites, with 11 species collected of the 18 total. Within each site, higher number of species were collected between 2 and 5 meters depth's.
Faulting Parameters of the January 16, 1994 Wyomissing Hills, Pennsylvania Earthquakes

USGS Publications Warehouse

Ammon, C.J.; Herrmann, Robert B.; Langston, C.A.; Benz, H.

1998-01-01

Two events dominated the January 1994, Wyomissing, PA earthquake sequence, an Mw 4.0 foreshock, followed by an Mw 4.6 mainshock. We modeled regional waveforms to estimate the event depth and the moment tensors for the two largest events in the sequence, and examine teleseismic wave-forms recorded on the ARCESS short-period seismic array to estimate the depth and source time function of the mainshock. Our data constrain the depth of the events to be shallower than 5 km, and prefer a depth of 3-5 km. For an assumed depth of 3 km, the mainshock moment tensor is 75% double couple, with (the major double couple) planes striking at 135??N, 347??N, dips of 49??, 46??, and rakes of 68??, 114??. The estimated moment is 8.9 ?? 1022 dyne-cm. The P axis strikes 241??N and plunges 2??, the Tension axis strikes 336??N and plunges 73??. The foreshock inversion results are virtually identical to the mainshock results; for a source depth of three km, we find a major double couple with a strike, dip, and rake of 121??N, 60??, and 66??, respectively. The seismic moment for the foreshock is 1.2 ?? 1022 dyne-cm, which is approximately 13% of the mainshock moment release. These events did not excite high-frequency Lg waves as effectively as typical eastern North American events, and the mainshock had a stress drop in the range of 25-50 bars.
Cutting holes in fabric-faced panels

NASA Technical Reports Server (NTRS)

Peterson, S. A.

1981-01-01

Tool has 2 carbide inserts that bore clean holes through fibrous material with knifelike slicing action. Cutting edge of insert is curved, with plane inner surface at 30 degree angle to tool axis. Drill press or hand-held drill can be used to hold cutting tool.
Conducting Creativity Brainstorming Sessions in Small and Medium-Sized Enterprises Using Computer-Mediated Communication Tools

NASA Astrophysics Data System (ADS)

Murthy, Uday S.

A variety of Web-based low cost computer-mediated communication (CMC) tools are now available for use by small and medium-sized enterprises (SME). These tools invariably incorporate chat systems that facilitate simultaneous input in synchronous electronic meeting environments, allowing what is referred to as “electronic brainstorming.” Although prior research in information systems (IS) has established that electronic brainstorming can be superior to face-to-face brainstorming, there is a lack of detailed guidance regarding how CMC tools should be optimally configured to foster creativity in SMEs. This paper discusses factors to be considered in using CMC tools for creativity brainstorming and proposes recommendations for optimally configuring CMC tools to enhance creativity in SMEs. The recommendations are based on lessons learned from several recent experimental studies on the use of CMC tools for rich brainstorming tasks that require participants to invoke domain-specific knowledge. Based on a consideration of the advantages and disadvantages of the various configuration options, the recommendations provided can form the basis for selecting a CMC tool for creativity brainstorming or for creating an in-house CMC tool for the purpose.
Design and usability of heuristic‐based deliberation tools for women facing amniocentesis

PubMed Central

Durand, Marie‐Anne; Wegwarth, Odette; Boivin, Jacky; Elwyn, Glyn

2011-01-01

Abstract Background Evidence suggests that in decision contexts characterized by uncertainty and time constraints (e.g. health‐care decisions), fast and frugal decision‐making strategies (heuristics) may perform better than complex rules of reasoning. Objective To examine whether it is possible to design deliberation components in decision support interventions using simple models (fast and frugal heuristics). Design The ‘Take The Best’ heuristic (i.e. selection of a ‘most important reason’) and ‘The Tallying’ integration algorithm (i.e. unitary weighing of pros and cons) were used to develop two deliberation components embedded in a Web‐based decision support intervention for women facing amniocentesis testing. Ten researchers (recruited from 15), nine health‐care providers (recruited from 28) and ten pregnant women (recruited from 14) who had recently been offered amniocentesis testing appraised evolving versions of ‘your most important reason’ (Take The Best) and ‘weighing it up’ (Tallying). Results Most researchers found the tools useful in facilitating decision making although emphasized the need for simple instructions and clear layouts. Health‐care providers however expressed concerns regarding the usability and clarity of the tools. By contrast, 7 out of 10 pregnant women found the tools useful in weighing up the pros and cons of each option, helpful in structuring and clarifying their thoughts and visualizing their decision efforts. Several pregnant women felt that ‘weighing it up’ and ‘your most important reason’ were not appropriate when facing such a difficult and emotional decision. Conclusion Theoretical approaches based on fast and frugal heuristics can be used to develop deliberation tools that provide helpful support to patients facing real‐world decisions about amniocentesis. PMID:21241434
Facilitating peer based learning through summative assessment - An adaptation of the Objective Structured Clinical Assessment tool for the blended learning environment.

PubMed

Wikander, Lolita; Bouchoucha, Stéphane L

2018-01-01

Adapting a course from face to face to blended delivery necessitates that assessments are modified accordingly. In Australia the Objective Structured Clinical Assessment tool, as a derivative from the Objective Structured Clinical Examination, has been used in the face-to-face delivery mode as a formative or summative assessment tool in medicine and nursing since 1990. The Objective Structured Clinical Assessment has been used at Charles Darwin University to assess nursing students' simulated clinical skills prior to the commencement of their clinical placements since 2008. Although the majority of the course is delivered online, students attend a one-week intensive clinical simulation block yearly, prior to attending clinical placements. Initially, the Objective Structured Clinical Assessment was introduced as a lecturer assessed summative assessment, over time it was adapted to better suit the blended learning environment. The modification of the tool from an academic to peer assessed assessment tool, was based on the empirical literature, student feedback and a cross-sectional, qualitative study exploring academics' perceptions of the Objective Structured Clinical Assessment (Bouchoucha et al., 2013a, b). This paper presents an overview of the process leading to the successful adaptation of the Objective Structured Clinical Assessment to suit the requirements of a preregistration nursing course delivered through blended learning. This is significant as many universities are moving their curriculum to fully online or blended delivery, yet little attention has been paid to adapting the assessment of simulated clinical skills. The aim is to identify the benefits and drawbacks of using the peer assessed Objective Structured Clinical Assessment and share recommendations for successful implementation. Copyright © 2017 Elsevier Ltd. All rights reserved.
Rotating hot-wire investigation of the vortex responsible for blade-vortex interaction noise

NASA Technical Reports Server (NTRS)

Fontana, Richard Remo

1988-01-01

This distribution of the circumferential velocity of the vortex responsible for blade-vortex interaction noise was measured using a rotating hot-wire rake synchronously meshed with a model helicopter rotor at the blade passage frequency. Simultaneous far-field acoustic data and blade differential pressure measurements were obtained. Results show that the shape of the measured far-field acoustic blade-vortex interaction signature depends on the blade-vortex interaction geometry. The experimental results are compared with the Widnall-Wolf model for blade-vortex interaction noise.
NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER HOT SHOT ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-4 FOR IDENTICAL B&W NEGATIVE. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA
NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER HOT SHOT ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-17 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

Advanced Noise Control Fan: A 20-Year Retrospective

NASA Technical Reports Server (NTRS)

Sutliff, Dan

2016-01-01

The ANCF test bed is used for evaluating fan noise reduction concepts, developing noise measurement technologies, and providing a database for Aero-acoustic code development. Rig Capabilities: 4 foot 16 bladed rotor @ 2500 rpm, Auxiliary air delivery system (3 lbm/sec @ 6/12 psi), Variable configuration (rotor pitch angle, stator count/position, duct length), synthetic acoustic noise generation (tone/broadband). Measurement Capabilities: 112 channels dynamic data system, Unique rotating rake mode measuremen, Farfield (variable radius), Duct wall microphones, Stator vane microphones, Two component CTA w/ traversing, ESP for static pressures.
Geometerial description for a proposed aeroassist flight experiment vehicle

NASA Technical Reports Server (NTRS)

Cheatwood, F. M.; Dejarnette, F. J.; Hamilton, H. H., II

1986-01-01

One geometry currently under consideration for the Aeroassist Flight Experiment (AFE) vehicle is composed of several segments of simple general conics: an ellipsoidal nose tangent to an elliptical cone and a base skirt with the base plane raked relative to the body axis. An analytic representation for the body coordinates and first and second partial derivatives of this configuration has been developed. Equations are given which define the body radius and partial derivatives for a prescribed axial and circumferential position on the vehicle. The results for a sample case are tabulated and presented graphically.
The investigation and implementation of real-time face pose and direction estimation on mobile computing devices

NASA Astrophysics Data System (ADS)

Fu, Deqian; Gao, Lisheng; Jhang, Seong Tae

2012-04-01

The mobile computing device has many limitations, such as relative small user interface and slow computing speed. Usually, augmented reality requires face pose estimation can be used as a HCI and entertainment tool. As far as the realtime implementation of head pose estimation on relatively resource limited mobile platforms is concerned, it is required to face different constraints while leaving enough face pose estimation accuracy. The proposed face pose estimation method met this objective. Experimental results running on a testing Android mobile device delivered satisfactory performing results in the real-time and accurately.
Creating a 'Born Digital' Introductory Online Geology Course with a Community of Inquiry that Supports Discussion of Societal Challenges

NASA Astrophysics Data System (ADS)

d'Alessio, M. A.; Schwartz, J. J.

2014-12-01

With earth science relevant to so many societal challenges, we created an introductory geology course as a forum for students to explore the interplay between geoscience and society. With new media and digital tools enabling such rich collaboration, we designed the course as a fully online lecture and laboratory experience that meets the natural science general education requirements of our university. We hook students by using popular Hollywood blockbusters paired with documentary films that address related science content. Student ask questions using an online question ranking tool (Google Moderator) to guide the direction of further content delivery using the slide sharing/collaboration tool 'VoiceThread.' It allows instructors to post slides, add video narration, and invite students to comment or answer specific questions using video, voice, or text. Students report that VoiceThread makes an asynchronous class feel like a face-to-face experience. Student also collect data using online tools and pool their data in Google Spreadsheets. They discuss their collective findings in VoiceThread. With these tools in place, each content unit culminates with a challenge scenario. Students work in teams to come to a consensus about a real-world decision that requires them to apply their geologic knowledge. Examples include whether or not to evacuate a town in light of volcanic activity, which house to purchase in an earthquake prone area, which industry was polluting local groundwater, and whether or not to sell mineral rights for hydraulic fracturing. While many of these activities are widely utilized, our approach using them in an integrated online lecture/lab environment is unique. A survey of student attitudes towards the course revealed that students felt a stronger personal connection to the course instructor and one another than typical face-to-face GE classes, including those from our own department. Students' self-report of how much they learned was strongly correlated to their perceived sense of community. We attribute the high course grades and low failure rates (30% A's with only 13% D/F/W) to this sense of community and the socially relevant content it enabled students to engage, as the scores were much higher than more traditional face-to-face courses taught by the same instructors.
Federated Search Tools in Fusion Centers: Bridging Databases in the Information Sharing Environment

DTIC Science & Technology

2012-09-01

considerable variation in how fusion centers plan for, gather requirements, select and acquire federated search tools to bridge disparate databases...centers, when considering integrating federated search tools; by evaluating the importance of the planning, requirements gathering, selection and...acquisition processes for integrating federated search tools; by acknowledging the challenges faced by some fusion centers during these integration processes
3rd Annual Earth System Grid Federation and 3rd Annual Earth System Grid Federation and Ultrascale Visualization Climate Data Analysis Tools Face-to-Face Meeting Report December 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Dean N.

The climate and weather data science community gathered December 3–5, 2013, at Lawrence Livermore National Laboratory, in Livermore, California, for the third annual Earth System Grid Federation (ESGF) and Ultra-scale Visualization Climate Data Analysis Tools (UV-CDAT) Face-to-Face (F2F) Meeting, which was hosted by the Department of Energy, National Aeronautics and Space Administration, National Oceanic and Atmospheric Administration, the European Infrastructure for the European Network of Earth System Modelling, and the Australian Department of Education. Both ESGF and UV-CDAT are global collaborations designed to develop a new generation of open-source software infrastructure that provides distributed access and analysis to observed andmore » simulated data from the climate and weather communities. The tools and infrastructure developed under these international multi-agency collaborations are critical to understanding extreme weather conditions and long-term climate change, while the F2F meetings help to build a stronger climate and weather data science community and stronger federated software infrastructure. The 2013 F2F meeting determined requirements for existing and impending national and international community projects; enhancements needed for data distribution, analysis, and visualization infrastructure; and standards and resources needed for better collaborations.« less
The "healthy lifestyle guide pyramid" for children and adolescents.

PubMed

González-Gross, M; Gómez-Lorente, J J; Valtueña, J; Ortiz, J C; Meléndez, A

2008-01-01

Increasing evidence demonstrates that risk factors for chronic diseases are established during childhood and adolescence. Consensus about the need to increase prevention efforts makes the adoption of a healthy lifestyle seem desirable from early childhood onwards. After reviewing educational tools for children and adolescents aimed at promoting a healthy lifestyle, it was recognized that there was a need to develop a simple educational tool specifically designed for these age groups. Development of the healthy lifestyle pyramid for children and adolescents. We propose a three-dimensional, truncated and staggered pyramid with 4 faces and a base, which introduces a completely new concept that goes beyond other published pyramids. Each of the faces is oriented towards achieving a different goal. Two faces (faces 1 and 2) are formulated around achieving a goal on a daily basis (daily food intake, face 1, and daily activities, face 2). Face 3 is an adaptation of the traditional food guide pyramid, adapted to children's energy, nutritional and hydration needs. Face 4 deals with both daily and life-long habits. On the base of the pyramid, there is advice about adequate nutrition alternating with advice about physical activity and sports. The Healthy Lifestyle Pyramid is specifically developed for children and adolescents according to current scientific knowledge and evidence-based data and includes easy-to-follow advice and full colour pictures. Following these guidelines should improve health and reduce risk factors, promoting enjoyable and appropriate development towards adulthood.
Arrangement for controlled engagement of the tools of a mining machine with a mine face

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blumenthal, G.; Bollmann, A.

1981-07-28

An arrangement for controlled engagement of the tools of a coal planer, with a mine face comprises a scraper conveyor, provided on its front face directed toward the mine face with a guide rail guiding the coal planer for reciprocation along the mine face and a mechanism for tilting the conveyor and the coal planer about a substantially horizontal axis. The tilting mechanism is connected to the rear face of the conveyor and extends in its entirety rearwardly of the rear face of the latter. The tilting mechanism comprises a guide linkage pivotally connected at its front end to themore » rear face of the scraper conveyor while its rear end portion forms a housing for a fluid operated cylinder and piston unit, the piston rod of which is connected to a connecting rod guided by the guide linkage for movement in longitudinal direction and having an upwardly extending front section pivotally connected at its upper free end to the rear face of the scraper conveyor. The fluid operated cylinder-and-piston unit is thus considerably spaced from the scraper conveyor and the material transported thereby and especially coal dust raised during transport of the mined coal by the conveyor, whereby maintenance of the tilting unit is reduced. The guide linkage, the connecting rod and the tilting unit are all in close vicinity to the sole of the mine gallery to leave a considerable free space between the arrangement and the roof of the mine gallery.« less
New Geometry of Worm Face Gear Drives with Conical and Cylindrical Worms: Generation, Simulation of Meshing, and Stress Analysis

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Nava, Alessandro; Fan, Qi; Fuentes, Alfonso

2002-01-01

New geometry of face worm gear drives with conical and cylindrical worms is proposed. The generation of the face worm-gear is based on application of a tilted head-cutter (grinding tool) instead of application of a hob applied at present. The generation of a conjugated worm is based on application of a tilted head-cutter (grinding tool) as well. The bearing contact of the gear drive is localized and is oriented longitudinally. A predesigned parabolic function of transmission errors for reduction of noise and vibration is provided. The stress analysis of the gear drive is performed using a three-dimensional finite element analysis. The contacting model is automatically generated. The developed theory is illustrated with numerical examples.
Alpha-band rhythm modulation under the condition of subliminal face presentation: MEG study.

PubMed

Sakuraba, Satoshi; Kobayashi, Hana; Sakai, Shinya; Yokosawa, Koichi

2013-01-01

The human brain has two streams to process visual information: a dorsal stream and a ventral stream. Negative potential N170 or its magnetic counterpart M170 is known as the face-specific signal originating from the ventral stream. It is possible to present a visual image unconsciously by using continuous flash suppression (CFS), which is a visual masking technique adopting binocular rivalry. In this work, magnetoencephalograms were recorded during presentation of the three invisible images: face images, which are processed by the ventral stream; tool images, which could be processed by the dorsal stream, and a blank image. Alpha-band activities detected by sensors that are sensitive to M170 were compared. The alpha-band rhythm was suppressed more during presentation of face images than during presentation of the blank image (p=.028). The suppression remained for about 1 s after ending presentations. However, no significant difference was observed between tool and other images. These results suggest that alpha-band rhythm can be modulated also by unconscious visual images.
Development and Early Usage Patterns of a Consumer-Facing Family Health History Tool

PubMed Central

Hulse, Nathan C.; Ranade-Kharkar, Pallavi; Post, Herman; Wood, Grant M.; Williams, Marc S.; Haug, Peter J.

2011-01-01

Personalized medicine will require detailed clinical patient profiles, and a particular focus on capturing data that is useful in forecasting risk. A detailed family health history is considered a critical component of these profiles, insomuch that it has been coined as ‘the best genetic test available’. Despite this, tools aimed at capturing this information for use in electronic health records have been characterized as inadequate. In this manuscript we detail the creation of a patient-facing family health history tool known as OurFamilyHealth, whose long-term emphasis is to facilitate risk assessment and clinical decision support. We present the rationale for such a tool, describe its development and release as a component of Intermountain Healthcare’s patient portal, and detail early usage statistics surrounding the application. Data derived from the tool since its release are also compared against family history charting patterns in Intermountain’s electronic health records, revealing differences in data availability. PMID:22195113
Development of Anthropometric Analogous Headforms. Phase 1.

DTIC Science & Technology

1994-10-31

shown in figure 5. This surface mesh can then be transformed into polygon faces that are able to be rendered by the AutoCAD rendering tools . Rendering of...computer-generated surfaces. The material removal techniques require the programming of the tool path of the cutter and in some cases requires specialized... tooling . Tool path programs are available to transfer the computer-generated surface into actual paths of the cutting tool . In cases where the
The Right Tools for the Right Jobs.

ERIC Educational Resources Information Center

Barbalich, Andrea, Ed.

1995-01-01

A chart shows the best campus public relations uses for 17 communication techniques: face-to-face contact; phone call, regular mail; electronic mail; special events; a speech; press release; press kit; press conference; television and radio public service announcements; video news releases; promotions and posters; advertising; newsletter;…
Incorporating Collaborative Technologies into University Curricula: Lessons Learned

ERIC Educational Resources Information Center

Hunt, C. Steven; Smith, Lola B.; Chen, Minder

2010-01-01

Web-based collaboration tools and groupware are uniquely qualified to address the emerging business opportunities heretofore hindered by location barriers, constraints of time, and expensive travel costs. Global business enterprises are implementing online collaboration software to augment their face-to-face meetings and group decision making in…
BatTool: an R package with GUI for assessing the effect of White-nose syndrome and other take events on Myotis spp. of bats

PubMed Central

2014-01-01

Background Myotis species of bats such as the Indiana Bat and Little Brown Bat are facing population declines because of White-nose syndrome (WNS). These species also face threats from anthropogenic activities such as wind energy development. Population models may be used to provide insights into threats facing these species. We developed a population model, BatTool, as an R package to help decision makers and natural resource managers examine factors influencing the dynamics of these species. The R package includes two components: 1) a deterministic and stochastic model that are accessible from the command line and 2) a graphical user interface (GUI). Results BatTool is an R package allowing natural resource managers and decision makers to understand Myotis spp. population dynamics. Through the use of a GUI, the model allows users to understand how WNS and other take events may affect the population. The results are saved both graphically and as data files. Additionally, R-savvy users may access the population functions through the command line and reuse the code as part of future research. This R package could also be used as part of a population dynamics or wildlife management course. Conclusions BatTool provides access to a Myotis spp. population model. This tool can help natural resource managers and decision makers with the Endangered Species Act deliberations for these species and with issuing take permits as part of regulatory decision making. The tool is available online as part of this publication. PMID:24955110
BatTool: an R package with GUI for assessing the effect of White-nose syndrome and other take events on Myotis spp. of bats

USGS Publications Warehouse

Erickson, Richard A.; Thogmartin, Wayne E.; Szymanski, Jennifer A.

2014-01-01

Background: Myotis species of bats such as the Indiana Bat and Little Brown Bat are facing population declines because of White-nose syndrome (WNS). These species also face threats from anthropogenic activities such as wind energy development. Population models may be used to provide insights into threats facing these species. We developed a population model, BatTool, as an R package to help decision makers and natural resource managers examine factors influencing the dynamics of these species. The R package includes two components: 1) a deterministic and stochastic model that are accessible from the command line and 2) a graphical user interface (GUI). Results: BatTool is an R package allowing natural resource managers and decision makers to understand Myotis spp. population dynamics. Through the use of a GUI, the model allows users to understand how WNS and other take events may affect the population. The results are saved both graphically and as data files. Additionally, R-savvy users may access the population functions through the command line and reuse the code as part of future research. This R package could also be used as part of a population dynamics or wildlife management course. Conclusions: BatTool provides access to a Myotis spp. population model. This tool can help natural resource managers and decision makers with the Endangered Species Act deliberations for these species and with issuing take permits as part of regulatory decision making. The tool is available online as part of this publication.
BatTool: an R package with GUI for assessing the effect of White-nose syndrome and other take events on Myotis spp. of bats.

PubMed

Erickson, Richard A; Thogmartin, Wayne E; Szymanski, Jennifer A

2014-01-01

Myotis species of bats such as the Indiana Bat and Little Brown Bat are facing population declines because of White-nose syndrome (WNS). These species also face threats from anthropogenic activities such as wind energy development. Population models may be used to provide insights into threats facing these species. We developed a population model, BatTool, as an R package to help decision makers and natural resource managers examine factors influencing the dynamics of these species. The R package includes two components: 1) a deterministic and stochastic model that are accessible from the command line and 2) a graphical user interface (GUI). BatTool is an R package allowing natural resource managers and decision makers to understand Myotis spp. population dynamics. Through the use of a GUI, the model allows users to understand how WNS and other take events may affect the population. The results are saved both graphically and as data files. Additionally, R-savvy users may access the population functions through the command line and reuse the code as part of future research. This R package could also be used as part of a population dynamics or wildlife management course. BatTool provides access to a Myotis spp. population model. This tool can help natural resource managers and decision makers with the Endangered Species Act deliberations for these species and with issuing take permits as part of regulatory decision making. The tool is available online as part of this publication.
Emissions Prediction and Measurement for Liquid-Fueled TVC Combustor with and without Water Injection

NASA Technical Reports Server (NTRS)

Brankovic, A.; Ryder, R. C., Jr.; Hendricks, R. C.; Liu, N.-S.; Shouse, D. T.; Roquemore, W. M.

2005-01-01

An investigation is performed to evaluate the performance of a computational fluid dynamics (CFD) tool for the prediction of the reacting flow in a liquid-fueled combustor that uses water injection for control of pollutant emissions. The experiment consists of a multisector, liquid-fueled combustor rig operated at different inlet pressures and temperatures, and over a range of fuel/air and water/fuel ratios. Fuel can be injected directly into the main combustion airstream and into the cavities. Test rig performance is characterized by combustor exit quantities such as temperature and emissions measurements using rakes and overall pressure drop from upstream plenum to combustor exit. Visualization of the flame is performed using gray scale and color still photographs and high-frame-rate videos. CFD simulations are performed utilizing a methodology that includes computer-aided design (CAD) solid modeling of the geometry, parallel processing over networked computers, and graphical and quantitative post-processing. Physical models include liquid fuel droplet dynamics and evaporation, with combustion modeled using a hybrid finite-rate chemistry model developed for Jet-A fuel. CFD and experimental results are compared for cases with cavity-only fueling, while numerical studies of cavity and main fueling was also performed. Predicted and measured trends in combustor exit temperature, CO and NOx are in general agreement at the different water/fuel loading rates, although quantitative differences exist between the predictions and measurements.
Effect of punch tip geometry and embossment on the punch tip adherence of a model ibuprofen formulation.

PubMed

Roberts, Matthew; Ford, James L; MacLeod, Graeme S; Fell, John T; Smith, George W; Rowe, Philip H; Dyas, A Mark

2004-07-01

The sticking of a model ibuprofen-lactose formulation with respect to compaction force, punch tip geometry and punch tip embossment was assessed. Compaction was performed at 10, 25 or 40 kN using an instrumented single-punch tablet press. Three sets of 'normal' concave punches were used to evaluate the influence of punch curvature and diameter. The punches were 10, 11 and 12 mm in diameter, respectively. The 10-mm punch was embossed with a letter 'A' logo to assess the influence of an embossment on sticking. Flat-faced punches (12.5 mm) were used for comparison with the concave tooling. Surface profiles (Taylor Hobson Talysurf 120) of the upper punch faces were obtained to evaluate the surface quality of the tooling used. Following compaction, ibuprofen attached to the upper punch face was quantified by spectroscopy. Increasing punch curvature from flat-faced punches to concave decreased sticking. Altering punch diameter of the concave punches had no effect on sticking when expressed as microg mm(-2). The embossed letter 'A' logo increased sticking considerably owing to the probable concentration of shear stresses at the lateral faces of the embossed logo.
Face-n-Food: Gender Differences in Tuning to Faces.

PubMed

Pavlova, Marina A; Scheffler, Klaus; Sokolov, Alexander N

2015-01-01

Faces represent valuable signals for social cognition and non-verbal communication. A wealth of research indicates that women tend to excel in recognition of facial expressions. However, it remains unclear whether females are better tuned to faces. We presented healthy adult females and males with a set of newly created food-plate images resembling faces (slightly bordering on the Giuseppe Arcimboldo style). In a spontaneous recognition task, participants were shown a set of images in a predetermined order from the least to most resembling a face. Females not only more readily recognized the images as a face (they reported resembling a face on images, on which males still did not), but gave on overall more face responses. The findings are discussed in the light of gender differences in deficient face perception. As most neuropsychiatric, neurodevelopmental and psychosomatic disorders characterized by social brain abnormalities are sex specific, the task may serve as a valuable tool for uncovering impairments in visual face processing.

Face-n-Food: Gender Differences in Tuning to Faces

PubMed Central

Pavlova, Marina A.; Scheffler, Klaus; Sokolov, Alexander N.

2015-01-01

Faces represent valuable signals for social cognition and non-verbal communication. A wealth of research indicates that women tend to excel in recognition of facial expressions. However, it remains unclear whether females are better tuned to faces. We presented healthy adult females and males with a set of newly created food-plate images resembling faces (slightly bordering on the Giuseppe Arcimboldo style). In a spontaneous recognition task, participants were shown a set of images in a predetermined order from the least to most resembling a face. Females not only more readily recognized the images as a face (they reported resembling a face on images, on which males still did not), but gave on overall more face responses. The findings are discussed in the light of gender differences in deficient face perception. As most neuropsychiatric, neurodevelopmental and psychosomatic disorders characterized by social brain abnormalities are sex specific, the task may serve as a valuable tool for uncovering impairments in visual face processing. PMID:26154177
Improved tool grinding machine

DOEpatents

Dial, C.E. Sr.

The present invention relates to an improved tool grinding mechanism for grinding single point diamond cutting tools to precise roundness and radius specifications. The present invention utilizes a tool holder which is longitudinally displaced with respect to the remainder of the grinding system due to contact of the tool with the grinding surface with this displacement being monitored so that any variation in the grinding of the cutting surface such as caused by crystal orientation or tool thicknesses may be compensated for during the grinding operation to assure the attainment of the desired cutting tool face specifications.
Tool grinding machine

DOEpatents

Dial, Sr., Charles E.

1980-01-01

The present invention relates to an improved tool grinding mechanism for grinding single point diamond cutting tools to precise roundness and radius specifications. The present invention utilizes a tool holder which is longitudinally displaced with respect to the remainder of the grinding system due to contact of the tool with the grinding surface with this displacement being monitored so that any variation in the grinding of the cutting surface such as caused by crystal orientation or tool thickness may be compensated for during the grinding operation to assure the attainment of the desired cutting tool face specifications.
Challenges When Introducing Electronic Exam

ERIC Educational Resources Information Center

Kuikka, Matti; Kitola, Markus; Laakso, Mikko-Jussi

2014-01-01

Time pressures often necessitate the use of more efficient exam tools, such as electronic exams (e-exams), instead of traditional paper exams. However, teachers may face challenges when introducing e-exams in a higher education context. This paper describes what kinds of challenges teachers may face when introducing e-exams, based on experiences…
Effects of Feeding Back the Motivation of a Collaboratively Learning Group

ERIC Educational Resources Information Center

Schoor, Cornelia; Kownatzki, Salome; Narciss, Susanne; Körndle, Hermann

2014-01-01

Introduction: Motivation is an important issue in both face-to-face and computer-supported collaborative learning. There are several approaches for enhancing motivation, including group awareness tools that provide feedback on the group's motivation. However, this feedback was rarely unconfounded with other constructs. Additionally, it is…
Synchronous E-Learning: Reflections and Design Considerations

ERIC Educational Resources Information Center

Tabak, Filiz; Rampal, Rohit

2014-01-01

This paper is a personal reflection on the design, development, and delivery of online synchronous conferencing as a pedagogical tool complementing traditional, face-to-face content delivery and learning. The purpose of the paper is to demonstrate how instructors can combine collaborative and virtual learning principles in course design. In…
The Development of Emotional Face Processing during Childhood

ERIC Educational Resources Information Center

Batty, Magali; Taylor, Margot J.

2006-01-01

Our facial expressions give others the opportunity to access our feelings, and constitute an important nonverbal tool for communication. Many recent studies have investigated emotional perception in adults, and our knowledge of neural processes involved in emotions is increasingly precise. Young children also use faces to express their internal…
Automated Feedback as a Convergence Tool

ERIC Educational Resources Information Center

Chenoweth, Tim; Corral, Karen; Scott, Kit

2016-01-01

This study evaluates two content delivery options for teaching a programming language to determine whether an asynchronous format can achieve the same learning efficacy as a traditional lecture (face-to-face) format. We use media synchronicity theory as a guide to choose media capabilities to incorporate into an asynchronous tutorial used…
Using Multimedia Tools to Support Teacher Candidates' Learning

ERIC Educational Resources Information Center

Kennedy, Michael J.; Ely, Emily; Thomas, Cathy Newman; Pullen, Paige C.; Newton, Jennifer R.; Ashworth, Kristen; Cole, Mira T.; Lovelace, Shelly P.

2012-01-01

Content Acquisition Podcasts (CAPs), created using Mayer's Cognitive Theory of Multimedia Learning, are a form of instructional technology that can deliver critical course content and be used by teacher educators to conserve limited face-to-face instructional time. In this study, the authors investigate whether the sequence of instruction for CAP…
Researching for Public Speaking Classes: Requiring Various Media.

ERIC Educational Resources Information Center

Greenberg, Cindy A.

This paper presents steps for incorporating research into a community college public speaking class curriculum. It outlines, from an historical perspective, the different techniques and tools of research, including face-to-face contact, the printing press, modern machinery, and computers. It suggests discussing research surveys and taking students…
Facing History and Ourselves: An Instructional Tool for Constructivist Theory.

ERIC Educational Resources Information Center

Presseisen, Barbara Z.; Beyer, Francine S.

This paper presents a study using "Facing History and Ourselves," an interdisciplinary approach to knowledge development that focuses on the period of Nazi totalitarianism as a powerful case study through which teachers can stimulate moral reasoning and develop critical thinking skills in their students. The program encourages teenage…
Face-to-Face Collaborative Learning Supported by Mobile Phones

ERIC Educational Resources Information Center

Echeverria, Alejandro; Nussbaum, Miguel; Calderon, Juan Felipe; Bravo, Claudio; Infante, Cristian; Vasquez, Andrea

2011-01-01

The use of handheld computers in educational contexts has increased considerably in recent years and their value as a teaching tool has been confirmed by many positive experiences, particular within collaborative learning systems (Mobile Computer Supported Collaborative Learning [MCSCL]). The cost of the devices has hindered widespread use in…
Increasing Student Engagement Using Asynchronous Learning

ERIC Educational Resources Information Center

Northey, Gavin; Bucic, Tania; Chylinski, Mathew; Govind, Rahul

2015-01-01

Student engagement is an ongoing concern for educators because of its positive association with deep learning and educational outcomes. This article tests the use of a social networking site (Facebook) as a tool to facilitate asynchronous learning opportunities that complement face-to-face interactions and thereby enable a stronger learning…
The New Parent Checklist: A Tool to Promote Parental Reflection.

PubMed

Keys, Elizabeth M; McNeil, Deborah A; Wallace, Donna A; Bostick, Jason; Churchill, A Jocelyn; Dodd, Maureen M

To design and establish content and face validity of an evidence-informed tool that promotes parental self-reflection during the transition to parenthood. The New Parent Checklist was developed using a three-phase sequential approach: Phase 1 a scoping review and expert consultation to develop and refine a prototype tool; Phase 2 content analysis of parent focus groups; and Phase 3 assessment of utility in a cross-sectional sample of parents completing the New Parent Checklist and a questionnaire. The initial version of the checklist was considered by experts to contain key information. Focus group participants found it useful, appropriate, and nonjudgmental, and offered suggestions to enhance readability, utility, as well as face and content validity. In the cross-sectional survey, 83% of the participants rated the New Parent Checklist as "helpful" or "very helpful" and 90% found the New Parent Checklist "very easy" to use. Open-ended survey responses included predominantly positive feedback. Notable differences existed for some items based on respondents' first language, age, and sex. Results and feedback from all three phases informed the current version, available for download online. The New Parent Checklist is a comprehensive evidence-informed self-reflective tool with promising content and face validity. Depending on parental characteristics and infant age, certain items of the New Parent Checklist have particular utility but may also require further adaptation and testing. Local resources for information and/or support are included in the tool and could be easily adapted by other regions to incorporate their own local resources.
TELMA: Technology-enhanced learning environment for minimally invasive surgery.

PubMed

Sánchez-González, Patricia; Burgos, Daniel; Oropesa, Ignacio; Romero, Vicente; Albacete, Antonio; Sánchez-Peralta, Luisa F; Noguera, José F; Sánchez-Margallo, Francisco M; Gómez, Enrique J

2013-06-01

Cognitive skills training for minimally invasive surgery has traditionally relied upon diverse tools, such as seminars or lectures. Web technologies for e-learning have been adopted to provide ubiquitous training and serve as structured repositories for the vast amount of laparoscopic video sources available. However, these technologies fail to offer such features as formative and summative evaluation, guided learning, or collaborative interaction between users. The "TELMA" environment is presented as a new technology-enhanced learning platform that increases the user's experience using a four-pillared architecture: (1) an authoring tool for the creation of didactic contents; (2) a learning content and knowledge management system that incorporates a modular and scalable system to capture, catalogue, search, and retrieve multimedia content; (3) an evaluation module that provides learning feedback to users; and (4) a professional network for collaborative learning between users. Face validation of the environment and the authoring tool are presented. Face validation of TELMA reveals the positive perception of surgeons regarding the implementation of TELMA and their willingness to use it as a cognitive skills training tool. Preliminary validation data also reflect the importance of providing an easy-to-use, functional authoring tool to create didactic content. The TELMA environment is currently installed and used at the Jesús Usón Minimally Invasive Surgery Centre and several other Spanish hospitals. Face validation results ascertain the acceptance and usefulness of this new minimally invasive surgery training environment. Copyright © 2013 Elsevier Inc. All rights reserved.
Occurrence detection and selection procedures in healthcare facilities: a comparison across Canada and Brazil.

PubMed

Morita, Plinio P; Burns, Catherine M

2011-01-01

Healthcare institutions face high levels of risk on a daily basis. Efforts have been made to address these risks and turn this complex environment into a safer environment for patients, staff, and visitors. However, healthcare institutions need more advanced risk management tools to achieve the safety levels currently seen in other industries. One of these potential tools is occurrence investigation systems. In order to be investigated, occurrences must be detected and selected for investigation, since not all institutions have enough resources to investigate all occurrences. A survey was conducted in healthcare institutions in Canada and Brazil to evaluate currently used risk management tools, the difficulties faced, and the possibilities for improvement. The findings include detectability difficulties, lack of resources, lack of support, and insufficient staff involvement.
Wind Tunnel Results from a Nozzle Afterbody Test of a 0.2-Scale Fighter Aircraft in the Mach Number Regime of 0.6 to 1.5. Volume 1. Test Technique Evaluation

DTIC Science & Technology

1979-04-01

edge up. The influence of the aircraft on the static pressure reading from the pitot boom was determined with a scaled version of the pltot probe...stabilization before advancing to the next port. Jet exhaust simulation flow was monitored by internal duct pressure and temperature rakes . Standard...Mach numbers 0.6 and 1.2, Figs. 24 and 25. 13 AE DC-TR-79-10 At supersonic speeds, changes in the afterbody and nozzle axial loads (Fig. 22b) are
Connections between survey calibration estimators and semiparametric models for incomplete data

PubMed Central

Lumley, Thomas; Shaw, Pamela A.; Dai, James Y.

2012-01-01

Survey calibration (or generalized raking) estimators are a standard approach to the use of auxiliary information in survey sampling, improving on the simple Horvitz–Thompson estimator. In this paper we relate the survey calibration estimators to the semiparametric incomplete-data estimators of Robins and coworkers, and to adjustment for baseline variables in a randomized trial. The development based on calibration estimators explains the ‘estimated weights’ paradox and provides useful heuristics for constructing practical estimators. We present some examples of using calibration to gain precision without making additional modelling assumptions in a variety of regression models. PMID:23833390
Measurement of beam divergence of 30-centimeter dished grids

NASA Technical Reports Server (NTRS)

Danilowicz, R. L.; Rawlin, V. K.; Banks, B. A.; Wintucky, E. G.

1973-01-01

The beam divergence of a 30-centimeter diameter thruster with dished grids was calculated from current densities measured with a probe rake containing seventeen planar molybdenum probes. The measured data were analyzed as a function of a number of parameters. The most sensitive parameters were the amount of compensation of the accelerator grid and the ratio of net to total accelerating voltage. The thrust losses were reduced by over 5 percent with the use of compensated grids alone, and by variation of other parameters the overall thrust losses due to beam divergence were reduced to less than 2 percent.
Identification of atmospheric structure by coherent microwave sounding

NASA Technical Reports Server (NTRS)

Birkemeier, W. P.

1969-01-01

Two atmospheric probing experiments involving beyond-the-horizon propagation of microwave signals are reported. In the first experiment, Doppler-shift caused by the cross path wind is measured by a phase lock receiver with the common volume displaced in azimuth from the great circle. Variations in the measured Doppler shift values are explained in terms of variations in atmospheric structure. The second experiment makes use of the pseudorandom sounding signal used in a RAKE communication system. Both multipath delay and Doppler shift are provided by the receiver, permitting the cross section of the atmospheric layer structure to be deduced.

Ship To Ship Pulse Recognition System

DTIC Science & Technology

1941-10-24

rflr" scrcwtirivar. At the tW;, a: tte cAbinet are a pli,; connectio f~Lrom, tae .uplexer to the antenn -a switci., t:.e control oea n to the antenna...The blinker li.)it uwncs L~.. sec 15 wrntto U1S Volt ia.;isa in ’WijarajL J1i. ’fli* p~rcp&a~aioY1 syv~o- (antmnnimi Antenne switch aind fIlipiexer...Iinput to thePrWsel•etr Is a 31/Sm coOentric line whose center conductor rakes a eml loop to pound which servos to inductively couple the antma system
Measurement of beam divergence of 30-centimeter dished grids

NASA Technical Reports Server (NTRS)

Danilowicz, R. L.; Rawlin, V. K.; Banks, B. A.; Wintucky, E. G.

1973-01-01

The beam divergence of a 30-centimeter diameter thrustor with dished grids was calculated from current densities measured with a probe rake containing seventeen planar molybdenum probes. The measured data were analyzed as a function of a number of parameters. The most sensitive parameters were the amount of compensation of the accelerator grid and the ratio of net to total accelerating voltage. The thrust losses were reduced by over 5 percent with the use of compensated grids alone, and by variation of other parameters the overall thrust losses due to beam divergence were reduced to less than 2 percent.
Influence of technical parameters of disk-shaped reactor on productivity of heat treatment of crushed wood

NASA Astrophysics Data System (ADS)

Safin, R. R.; Khasanshin, R. R.; Mukhametzyanov, S. R.

2018-03-01

The existing installations for heat treatment of the crushed wood are analyzed. The technology of heat treatment of the crushed wood in the devices of disk-shaped type is offered. The results of modeling for the purpose of determination of interrelation of the key design and technological parameters of the disk-shaped device are presented. It is established that the major factors, affecting duration of stay of the material in a device, are the speed of rotation of the mixer, the number of mixers and the number of rakes on the mixer.
Experimental Study of the Influence of Speed and Load on Thermal Behavior of High-Speed Helical Gear Trains

NASA Technical Reports Server (NTRS)

Handschuh, R.; Kilmain, C.

2005-01-01

An experimental effort has been conducted on an aerospace-quality helical gear train to investigate the thermal behavior of the gear system as speed, load, and lubricant flow rate were varied. Temperature test data from a helical gear train at varying speeds and loads (to 5000 hp and 15000 rpm) was collected using thermocouple rakes and axial arrays. The instrumentation was able to capture the radial and axial expelled lubricant-air environment (fling-off lubricant) that is expelled during the gear meshing process. Effects of operational characteristics are presented.
A medical home: value and implications of knowledge management.

PubMed

Orzano, A John; McInerney, Claire R; McDaniel, Reuben R; Meese, Abigail; Alajmi, Bibi; Mohr, Stewart M; Tallia, Alfred F

2009-01-01

Central to the "medical home" concept is the premise that the delivery of effective primary care requires a fundamental shift in relationships among practice members and between practice members and patients. Primary care practices can potentially increase their capacity to deliver effective care through knowledge management (KM), a process of sharing and making existing knowledge available or by developing new knowledge among practice members and patients. KM affects performance by influencing work relationships to enhance learning, decision making, and task execution. We extend our previous work to further characterize, describe, and contrast how primary care practices exhibit KM and explain why KM deserves attention in medical home redesign initiatives. Case studies were conducted, drawn from two higher and lower performing practices, which were purposely selected based on disease management, prevention, and productivity measures from an improvement trial. Observations of operations, clinical encounters, meetings, and interviews with office members and patients were transcribed and coded independently using a KM template developed from a previous secondary analysis. Face-to-face discussions resolved coding differences among research team members. Confirmation of findings was sought from practice participants. Practices manifested varying degrees of KM effectiveness through six interdependent processes and multiple overlapping tools. Social tools, such as face-to-face-communication for sharing and developing knowledge, were often more effective than were expensive technical tools such as an electronic medical record. Tool use was tailored for specific outcomes, interacted with each other, and leveraged by other organizational capacities. Practices with effective KM were more open to adopting and sustaining new ways of functioning, ways reflecting attributes of a medical home. Knowledge management differences occur within and between practices and can explain differences in performance. By relying more on social tools rather than costly, high-tech investment, KM leverages primary care's relationship-centered strength, facilitating practice redesign as a medical home.
Blended learning: how can we optimise undergraduate student engagement?

PubMed

Morton, Caroline E; Saleh, Sohag N; Smith, Susan F; Hemani, Ashish; Ameen, Akram; Bennie, Taylor D; Toro-Troconis, Maria

2016-08-04

Blended learning is a combination of online and face-to-face learning and is increasingly of interest for use in undergraduate medical education. It has been used to teach clinical post-graduate students pharmacology but needs evaluation for its use in teaching pharmacology to undergraduate medical students, which represent a different group of students with different learning needs. An existing BSc-level module on neuropharmacology was redesigned using the Blended Learning Design Tool (BLEnDT), a tool which uses learning domains (psychomotor, cognitive and affective) to classify learning outcomes into those taught best by self-directed learning (online) or by collaborative learning (face-to-face). Two online courses were developed, one on Neurotransmitters and the other on Neurodegenerative Conditions. These were supported with face-to-face tutorials. Undergraduate students' engagement with blended learning was explored by the means of three focus groups, the data from which were analysed thematically. Five major themes emerged from the data 1) Purpose and Acceptability 2) Structure, Focus and Consolidation 3) Preparation and workload 4) Engagement with e-learning component 5) Future Medical Education. Blended learning was acceptable and of interest to undergraduate students learning this subject. They expressed a desire for more blended learning in their courses, but only if it was highly structured, of high quality and supported by tutorials. Students identified that the 'blend' was beneficial rather than purely online learning.
Assessing face validity of a physical activity questionnaire for Spanish-speaking women in California

USDA-ARS?s Scientific Manuscript database

Background: A review of the literature produced no rigorously tested and validated Spanish-language physical activity survey or evaluation tools for use by USDA’s food assistance and education programs. The purpose of the current study was to develop and evaluate the face validity of a visually enha...
Online Survey Design and Development: A Janus-Faced Approach

ERIC Educational Resources Information Center

Lauer, Claire; McLeod, Michael; Blythe, Stuart

2013-01-01

In this article we propose a "Janus-faced" approach to survey design--an approach that encourages researchers to consider how they can design and implement surveys more effectively using the latest web and database tools. Specifically, this approach encourages researchers to look two ways at once; attending to both the survey interface…
An Integrated Multimedia Learning Model vs. the Traditional Face-to-Face Learning Model: An Examination of College Economics Classes

ERIC Educational Resources Information Center

Son, Barbara; Simonian, Mark

2016-01-01

Multimedia learning tools can assist and help motivate students by supplementing traditional teaching modalities with learner-centered learning through application and practice. The overall effectiveness of multimedia learning has been documented (Son & Simonian, 2013; Son & Goldstone, 2012; Zhang, 2005). How are effective multimedia…
Overcoming Barriers between Volunteer Professionals Advising Project-Based Learning Teams with Regulation Tools

ERIC Educational Resources Information Center

Rees Lewis, Daniel G.; Easterday, Matthew W.; Harburg, Emily; Gerber, Elizabeth M.; Riesbeck, Christopher K.

2018-01-01

To provide the substantial support required for project-based learning (PBL), educators can incorporate professional experts as "design coaches." However, previous work shows barriers incorporating design coaches who can rarely meet face-to-face: (1) communication online is time-consuming, (2) updating coaches online is not perceived as…
Best Practices of Online Professional Development for K-12 Teachers: A Quantitative Study

ERIC Educational Resources Information Center

Smirniotis-Giambatista, Cynthia

2017-01-01

Online flipped professional development allows direct instruction to take place through an interactive learning setting and allows the face-to-face contact to provide guidance and apply the concept. As technology advances, education needs instruments and tools used for effectively teaching using the enhanced technology to increase student…
Supporting Blended-Learning: Tool Requirements and Solutions with OWLish

ERIC Educational Resources Information Center

Álvarez, Ainhoa; Martín, Maite; Fernández-Castro, Isabel; Urretavizcaya, Maite

2016-01-01

Currently, most of the educational approaches applied to higher education combine face-to-face (F2F) and computer-mediated instruction in a Blended-Learning (B-Learning) approach. One of the main challenges of these approaches is fully integrating the traditional brick-and-mortar classes with online learning environments in an efficient and…
From Bricks to Clicks: Blurring Classroom/Cyber Lines

ERIC Educational Resources Information Center

Pape, Liz

2006-01-01

In recent years, thanks to the evolution of the Internet, wide availability of classroom computers and increased broadband access, blended learning is emerging as a new tool in the K-12 educational toolkit. Defined as learning that combines online and face-to-face approaches, blended learning is accomplished through the combined use of virtual and…
Intercultural Reflection through the "Autobiography of Intercultural Encounters": Students' Accounts of Their Images of Alterity

ERIC Educational Resources Information Center

Méndez García, María del Carmen

2017-01-01

The Council of Europe's "Autobiography of Intercultural Encounter" (AIE) is a tool to develop intercultural competence (IC) in education by encouraging users to reflect upon and learn from momentous intercultural encounters they have experienced face to face. Its parallel resource, the "Autobiography of Intercultural Encounters…
The Viability of Google Wave as an Online Collaboration Tool

ERIC Educational Resources Information Center

Ovadia, Steven

2010-01-01

Collaboration is an increasingly important skill in academia. Not only are librarians expected to collaborate with one another within a single library, but there are also expectations of both intracampus and intercampus collaboration. While face-to-face and telephone meetings are often possible, there are times when everyone cannot be brought…
Weblog Technology for Instruction, Learning, and Information Delivery

ERIC Educational Resources Information Center

Shim, J. P.; Guo, Chengqi

2009-01-01

Ever since Weblog emerged as an infusive online communication tool over the last decade, its impacts have been witnessed by the Internet society at large. Meanwhile, more and more universities and colleges are offering online classes enhanced by Web technology. In this article, we investigate the role of Weblog combined with face-to-face lectures…
The Embedded Librarian Online or Face-to-Face: American University's Experiences

ERIC Educational Resources Information Center

Matos, Michael A.; Matsuoka-Motley, Nobue; Mayer, William

2010-01-01

This article examines the role online communication and tools play in embedded librarianship at American University. Two embedded models of user engagement, traditional and hybrid, are discussed. The librarians operating in each mode share their experiences providing tailored support to the departments of music/performing arts and business. The…
A Dynamic Analysis of the Interplay between Asynchronous and Synchronous Communication in Online Learning: The Impact of Motivation

ERIC Educational Resources Information Center

Giesbers, B.; Rienties, B.; Tempelaar, D.; Gijselaers, W.

2014-01-01

With the increased affordances of synchronous communication tools, more opportunities for online learning to resemble face-to-face settings have recently become available. However, synchronous communication does not afford as much time for reflection as asynchronous communication. Therefore, a combination of synchronous and asynchronous…
Embracing Distance Education in a Blended Learning Model: Challenges and Prospects

ERIC Educational Resources Information Center

Fresen, Jill W.

2018-01-01

Distance education reaches out to non-traditional students in geographically dispersed locations, who are unable to attend face-to-face classes. Contact institutions have been quick to realise the many advantages of distance (online) learning, such as easy access to learning materials, interactive activities, assessment and communication tools.…
Technology Transfer Challenges for High-Assurance Software Engineering Tools

NASA Technical Reports Server (NTRS)

Koga, Dennis (Technical Monitor); Penix, John; Markosian, Lawrence Z.

2003-01-01

In this paper, we describe our experience with the challenges thar we are currently facing in our effort to develop advanced software verification and validation tools. We categorize these challenges into several areas: cost benefits modeling, tool usability, customer application domain, and organizational issues. We provide examples of challenges in each area and identrfj, open research issues in areas which limit our ability to transfer high-assurance software engineering tools into practice.

The FaceBase Consortium: A comprehensive program to facilitate craniofacial research

PubMed Central

Hochheiser, Harry; Aronow, Bruce J.; Artinger, Kristin; Beaty, Terri H.; Brinkley, James F.; Chai, Yang; Clouthier, David; Cunningham, Michael L.; Dixon, Michael; Donahue, Leah Rae; Fraser, Scott E.; Hallgrimsson, Benedikt; Iwata, Junichi; Klein, Ophir; Marazita, Mary L.; Murray, Jeffrey C.; Murray, Stephen; de Villena, Fernando Pardo-Manuel; Postlethwait, John; Potter, Steven; Shapiro, Linda; Spritz, Richard; Visel, Axel; Weinberg, Seth M.; Trainor, Paul A.

2012-01-01

The FaceBase Consortium consists of ten interlinked research and technology projects whose goal is to generate craniofacial research data and technology for use by the research community through a central data management and integrated bioinformatics hub. Funded by the National Institute of Dental and Craniofacial Research (NIDCR) and currently focused on studying the development of the middle region of the face, the Consortium will produce comprehensive datasets of global gene expression patterns, regulatory elements and sequencing; will generate anatomical and molecular atlases; will provide human normative facial data and other phenotypes; conduct follow up studies of a completed genome-wide association study; generate independent data on the genetics of craniofacial development, build repositories of animal models and of human samples and data for community access and analysis; and will develop software tools and animal models for analyzing and functionally testing and integrating these data. The FaceBase website (http://www.facebase.org) will serve as a web home for these efforts, providing interactive tools for exploring these datasets, together with discussion forums and other services to support and foster collaboration within the craniofacial research community. PMID:21458441
Assessing adherence to the evidence base in the management of poststroke dysphagia.

PubMed

Burton, Christopher; Pennington, Lindsay; Roddam, Hazel; Russell, Ian; Russell, Daphne; Krawczyk, Karen; Smith, Hilary A

2006-01-01

To evaluate the reliability and responsiveness to change of an audit tool to assess adherence to evidence of effectiveness in the speech and language therapy (SLT) management of poststroke dysphagia. The tool was used to review SLT practice as part of a randomized study of different education strategies. Medical records were audited before and after delivery of the trial intervention. Seventeen SLT departments in the north-west of England participated in the study. The assessment tool was used to assess the medical records of 753 patients before and 717 patients after delivery of the trial intervention across the 17 departments. A target of 10 records per department per month was sought, using systematic sampling with a random start. Inter- and intra-rater reliability were explored, together with the tool's internal consistency and responsiveness to change. The assessment tool had high face validity, although internal consistency was low (ra = 0.37). Composite scores on the tool were however responsive to differences between SLT departments. Both inter- and intra-rater reliability ranged from 'substantial' to 'near perfect' across all items. The audit tool has high face validity and measurement reliability. The use of a composite adherence score should, however, proceed with caution as internal consistency is low.
Understanding the Delamination Risk of a Trilayer Tablet Using Minipiloting Tools.

PubMed

Tao, Jing; Robertson-Lavalle, Sophia; Pandey, Preetanshu; Badawy, Sherif

2017-11-01

A multilayer tablet is one of the formulation options used to mitigate chemical and physical incompatibility between different drug substances. Feasibility studies of multilayer tablets are often conducted using round flat-faced punch tooling. However, the link between different tooling designs and multilayer tablet performance is not well established. This study uses a prototype trilayer tablet and examines tooling design considerations when conducting small-scale studies to gauge the risk of interfacial defects. The impact of tablet weight and dimensions was evaluated to gain understanding of the effect of scale-up/down of tablet size. The factors in tooling selection, including tablet shape, cup depth, and size of embossing were evaluated to gain insight on the impact of tooling design on the interfacial strength of the trilayer tablet. It was found that tablet weight and dimensions can significantly affect the interfacial strength due to their impact on force transmission during compression and the retardation force from the die wall during ejection. Round flat-faced tooling generated trilayer tablets of the strongest interfacial strength compared to typical commercial tablets-oval shaped with concave surfaces. These factors should be accounted for when using round flat compacts to assess the interface risks of a multilayer tablet. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.
HappyFace as a generic monitoring tool for HEP experiments

NASA Astrophysics Data System (ADS)

Kawamura, Gen; Magradze, Erekle; Musheghyan, Haykuhi; Quadt, Arnulf; Rzehorz, Gerhard

2015-12-01

The importance of monitoring on HEP grid computing systems is growing due to a significant increase in their complexity. Computer scientists and administrators have been studying and building effective ways to gather information on and clarify a status of each local grid infrastructure. The HappyFace project aims at making the above-mentioned workflow possible. It aggregates, processes and stores the information and the status of different HEP monitoring resources into the common database of HappyFace. The system displays the information and the status through a single interface. However, this model of HappyFace relied on the monitoring resources which are always under development in the HEP experiments. Consequently, HappyFace needed to have direct access methods to the grid application and grid service layers in the different HEP grid systems. To cope with this issue, we use a reliable HEP software repository, the CernVM File System. We propose a new implementation and an architecture of HappyFace, the so-called grid-enabled HappyFace. It allows its basic framework to connect directly to the grid user applications and the grid collective services, without involving the monitoring resources in the HEP grid systems. This approach gives HappyFace several advantages: Portability, to provide an independent and generic monitoring system among the HEP grid systems. Eunctionality, to allow users to perform various diagnostic tools in the individual HEP grid systems and grid sites. Elexibility, to make HappyFace beneficial and open for the various distributed grid computing environments. Different grid-enabled modules, to connect to the Ganga job monitoring system and to check the performance of grid transfers among the grid sites, have been implemented. The new HappyFace system has been successfully integrated and now it displays the information and the status of both the monitoring resources and the direct access to the grid user applications and the grid collective services.
Engineered Surface Properties of Porous Tungsten from Cryogenic Machining

NASA Astrophysics Data System (ADS)

Schoop, Julius Malte

Porous tungsten is used to manufacture dispenser cathodes due to it refractory properties. Surface porosity is critical to functional performance of dispenser cathodes because it allows for an impregnated ceramic compound to migrate to the emitting surface, lowering its work function. Likewise, surface roughness is important because it is necessary to ensure uniform wetting of the molten impregnate during high temperature service. Current industry practice to achieve surface roughness and surface porosity requirements involves the use of a plastic infiltrant during machining. After machining, the infiltrant is baked and the cathode pellet is impregnated. In this context, cryogenic machining is investigated as a substitutionary process for the current plastic infiltration process. Along with significant reductions in cycle time and resource use, surface quality of cryogenically machined un-infiltrated (as-sintered) porous tungsten has been shown to significantly outperform dry machining. The present study is focused on examining the relationship between machining parameters and cooling condition on the as-machined surface integrity of porous tungsten. The effects of cryogenic pre-cooling, rake angle, cutting speed, depth of cut and feed are all taken into consideration with respect to machining-induced surface morphology. Cermet and Polycrystalline diamond (PCD) cutting tools are used to develop high performance cryogenic machining of porous tungsten. Dry and pre-heated machining were investigated as a means to allow for ductile mode machining, yet severe tool-wear and undesirable smearing limited the feasibility of these approaches. By using modified PCD cutting tools, high speed machining of porous tungsten at cutting speeds up to 400 m/min is achieved for the first time. Beyond a critical speed, brittle fracture and built-up edge are eliminated as the result of a brittle to ductile transition. A model of critical chip thickness ( hc ) effects based on cutting force, temperature and surface roughness data is developed and used to study the deformation mechanisms of porous tungsten under different machining conditions. It is found that when hmax = hc, ductile mode machining of otherwise highly brittle porous tungsten is possible. The value of hc is approximately the same as the average ligament size of the 80% density porous tungsten workpiece.
The use of Skype in a community hospital inpatient palliative medicine consultation service.

PubMed

Brecher, David B

2013-01-01

Skype™, an Internet-based communication tool, has enhanced communication under numerous circumstances. As telemedicine continues to be an increasing part of medical practice, there will be more opportunities to use Skype and similar tools. Numerous scenarios in the lay literature have helped to highlight the potential uses. Although most commonly used to enhance physician-to-patient communication, there has been limited reported use of Skype for patient-to-family communication, especially in end of life and palliative care. Our inpatient Palliative Medicine Consultation Service has offered and used this technology to enhance our patients' quality of life. The objective was to provide another tool for our patients to use to communicate with family and/or friends, especially under circumstances in which clinical symptoms, functional status, financial concerns, or geographic limitations preclude in-person face-to face communication.
Repeatable reference for positioning sensors and transducers in drill pipe

DOEpatents

Hall, David R.; Fox, Joe; Pixton, David S.; Hall, Jr., H. Tracy

2005-05-03

A drill pipe having a box end having a tapered thread, and an internal shoulder and an external face for engagement with a drill pipe pin end having a tapered mating thread, and an external shoulder and an external face adapted for data acquisition or transmission. The relative dimensions of the box and pin ends are precisely controlled so that when the tool joint is made up, a repeatable reference plane is established for transmitting power and tuning downhole sensors, transducers, and means for sending and receiving data along the drill string. When the power or data acquisition and transmission means are located in the tool joint, the dimensions of the tool joint are further proportioned to compensate for the loss of cross-sectional area in order maintain the joints ability to sustain nominal makeup torque.
Efficient live face detection to counter spoof attack in face recognition systems

NASA Astrophysics Data System (ADS)

Biswas, Bikram Kumar; Alam, Mohammad S.

2015-03-01

Face recognition is a critical tool used in almost all major biometrics based security systems. But recognition, authentication and liveness detection of the face of an actual user is a major challenge because an imposter or a non-live face of the actual user can be used to spoof the security system. In this research, a robust technique is proposed which detects liveness of faces in order to counter spoof attacks. The proposed technique uses a three-dimensional (3D) fast Fourier transform to compare spectral energies of a live face and a fake face in a mathematically selective manner. The mathematical model involves evaluation of energies of selective high frequency bands of average power spectra of both live and non-live faces. It also carries out proper recognition and authentication of the face of the actual user using the fringe-adjusted joint transform correlation technique, which has been found to yield the highest correlation output for a match. Experimental tests show that the proposed technique yields excellent results for identifying live faces.
Rupture Dynamics and Seismic Radiation on Rough Faults for Simulation-Based PSHA

NASA Astrophysics Data System (ADS)

Mai, P. M.; Galis, M.; Thingbaijam, K. K. S.; Vyas, J. C.; Dunham, E. M.

2017-12-01

Simulation-based ground-motion predictions may augment PSHA studies in data-poor regions or provide additional shaking estimations, incl. seismic waveforms, for critical facilities. Validation and calibration of such simulation approaches, based on observations and GMPE's, is important for engineering applications, while seismologists push to include the precise physics of the earthquake rupture process and seismic wave propagation in 3D heterogeneous Earth. Geological faults comprise both large-scale segmentation and small-scale roughness that determine the dynamics of the earthquake rupture process and its radiated seismic wavefield. We investigate how different parameterizations of fractal fault roughness affect the rupture evolution and resulting near-fault ground motions. Rupture incoherence induced by fault roughness generates realistic ω-2 decay for high-frequency displacement amplitude spectra. Waveform characteristics and GMPE-based comparisons corroborate that these rough-fault rupture simulations generate realistic synthetic seismogram for subsequent engineering application. Since dynamic rupture simulations are computationally expensive, we develop kinematic approximations that emulate the observed dynamics. Simplifying the rough-fault geometry, we find that perturbations in local moment tensor orientation are important, while perturbations in local source location are not. Thus, a planar fault can be assumed if the local strike, dip, and rake are maintained. The dynamic rake angle variations are anti-correlated with local dip angles. Based on a dynamically consistent Yoffe source-time function, we show that the seismic wavefield of the approximated kinematic rupture well reproduces the seismic radiation of the full dynamic source process. Our findings provide an innovative pseudo-dynamic source characterization that captures fault roughness effects on rupture dynamics. Including the correlations between kinematic source parameters, we present a new pseudo-dynamic rupture modeling approach for computing broadband ground-motion time-histories for simulation-based PSHA
Orthogonal cutting of laser beam melted parts

NASA Astrophysics Data System (ADS)

Götze, Elisa; Zanger, Frederik; Schulze, Volker

2018-05-01

The finishing process of parts manufactured by laser beam melting is of high concern due to the lack of surface accuracy. Therefore, the focus of this work lies on the influence of the build-up direction of the parts and their effect on the finishing process. The orthogonal cutting reveals findings in the fields of chip formation, involved forces and temperatures appearing during machining. In the investigations, the cutting depth was varied between 0.05 and 0.15 mm representing a finishing process and the cutting velocity ranges from 30 to 200 m/min depending on the material. The experiments contain the materials stainless steel (AISI 316L), titanium (Ti6Al4V) and nickel-base alloy (IN718). The two materials named latter are of high interest in the aerospace sector and at the same time titanium is used in the medical field due to its biocompatibility. For the materials IN718 and Ti6Al4V a negative rake angle of -7.5° and for stainless steel a rake angle of 12.5° are chosen for the cutting experiments. The results provide the base for processing strategies. Therefore, the specimens were solely laser beam melted without post-processing like heat treatment. The evaluation of the experiments shows that an increase in cutting speed has different effects depending on the material. For stainless steel the measured forces regarding the machining direction to the layers approach the same values. In contrast, the influence of the layers regarding the forces appearing during orthogonal cutting of the materials IN718 and Ti6Al4V differ for lower cutting speeds.
Childhood exposure to Libby amphibole during outdoor activities.

PubMed

Ryan, Patrick H; LeMasters, Grace K; Burkle, Jeffrey; Lockey, James E; Black, Brad; Rice, Carol

2015-01-01

Residents of Libby, MT were exposed to amphibole asbestos through multiple environmental pathways. Previous exposure characterization has primarily relied on qualitative report of these exposure activities. The objectives of this study were to describe available data from the US EPA preremediation actions for Libby amphibole (LA) exposure in Libby, MT and develop an approach to characterize outdoor residential exposure to LA among children. Homes in Libby, MT included in the US EPA preremediation Contaminant Screening Survey (CSS) were categorized by the presence of interior and/or exterior visible vermiculite and concentrations of LA were measured in samples of dust and soil. Airborne exposure to LA while digging/gardening, raking, and mowing were estimated using US EPA activity-based sampling (ABS) results. Residential histories and frequency/duration of childhood activities were combined with ABS to demonstrate the approach for estimating potential exposure. A total of 3154 residential properties participated in the CSS and 44% of these had visible exterior vermiculite. Airborne concentrations of LA where there was visible vermiculite outdoors were 3-15 times higher during digging/gardening, raking, and mowing activities compared with homes without visible outdoor vermiculite. Digging and gardening activities represented the greatest contribution to estimated exposures and 73% of the participants reported this activity before the age of 6 years. This methodology demonstrated the use of historical preremediation data to estimate residential exposures of children for specific activities. Children younger than age 6 years may have been exposed to LA while digging/gardening, especially at homes where there is visible outdoor vermiculite. This approach may be extended to other activities and applied to the entire cohort to examine health outcomes.
The 2016 Mihoub (north-central Algeria) earthquake sequence: Seismological and tectonic aspects

NASA Astrophysics Data System (ADS)

Khelif, M. F.; Yelles-Chaouche, A.; Benaissa, Z.; Semmane, F.; Beldjoudi, H.; Haned, A.; Issaadi, A.; Chami, A.; Chimouni, R.; Harbi, A.; Maouche, S.; Dabbouz, G.; Aidi, C.; Kherroubi, A.

2018-06-01

On 28 May 2016 at 23:54 (UTC), an Mw5.4 earthquake occurred in Mihoub village, Algeria, 60 km southeast of Algiers. This earthquake was the largest event in a sequence recorded from 10 April to 15 July 2016. In addition to the permanent national network, a temporary network was installed in the epicentral region after this shock. Recorded event locations allow us to give a general overview of the sequence and reveal the existence of two main fault segments. The first segment, on which the first event in the sequence was located, is near-vertical and trends E-W. The second fault plane, on which the largest event of the sequence was located, dips to the southeast and strikes NE-SW. A total of 46 well-constrained focal mechanisms were calculated. The events located on the E-W-striking fault segment show mainly right-lateral strike-slip (strike N70°E, dip 77° to the SSE, rake 150°). The events located on the NE-SW-striking segment show mainly reverse faulting (strike N60°E, dip 70° to the SE, rake 130°). We calculated the static stress change caused by the first event (Md4.9) of the sequence; the result shows that the fault plane of the largest event in the sequence (Mw5.4) and most of the aftershocks occurred within an area of increased Coulomb stress. Moreover, using the focal mechanisms calculated in this work, we estimated the orientations of the main axes of the local stress tensor ellipsoid. The results confirm previous findings that the general stress field in this area shows orientations aligned NNW-SSE to NW-SE. The 2016 Mihoub earthquake sequence study thus improves our understanding of seismic hazard in north-central Algeria.
Pitot survey of exhaust flow field of a 2-D scramjet nozzle at Mach 6 with air or freon and argon used for exhaust simulation

NASA Technical Reports Server (NTRS)

Monta, William J.

1992-01-01

A pitot-rake survey of the simulated exhaust of a half-span scramjet nozzle model was conducted in the Langley 20-Inch Mach 6 Tunnel to provide an additional data set for computational fluid dynamics (CFD) code comparisons. A wind-tunnel model was tested with a 26-tube pitot rake that could be manually positioned along the mid-semispan plane of the model. The model configuration had an external expansion surface of 20 degrees and an internal cowl expansion of 12 degrees; tests were also performed with a flow fence. Tests were conducted at a free-stream Reynolds number of approximately 6.5 x 10(exp 6) per foot and a model angle of attack of -0.75 degrees. The two exhaust gas mediums that were tested were air and a Freon 12-argon mixture. Each medium was tested at two jet total pressures at approximately 28 and 14 psia. This document presents the flow-field survey results in graphical as well as tabular form, and several observations concerning the results are discussed. The surveys reveal the major expected flow-field characteristics for each test configuration. For a 50-percent freon 12 and 50-percent argon mixture by volume (Fr-Ar), the exhaust jet pressures were slightly higher than those for air. The addition of a flow fence slightly raised the pitot pressure for the Fr-Ar mixture, but it produced little change for air. For the Fr-Ar exhaust, the plume was larger and the region between the shock wave and plume was smaller.
Teleseismic Body Wave Analysis for the 27 September 2003 Altai, Earthquake (Mw7.4) and Large Aftershocks

NASA Astrophysics Data System (ADS)

Gomez-Gonzalez, J. M.; Mellors, R.

2007-05-01

We investigate the kinematics of the rupture process for the September 27, 2003, Mw7.3, Altai earthquake and its associated large aftershocks. This is the largest earthquake striking the Altai mountains within the last 50 years, which provides important constraints on the ongoing tectonics. The fault plane solution obtained by teleseismic body waveform modeling indicated a predominantly strike-slip event (strike=130, dip=75, rake 170), Scalar moment for the main shock ranges from 0.688 to 1.196E+20 N m, a source duration of about 20 to 42 s, and an average centroid depth of 10 km. Source duration would indicate a fault length of about 130 - 270 km. The main shock was followed closely by two aftershocks (Mw5.7, Mw6.4) occurred the same day, another aftershock (Mw6.7) occurred on 1 October , 2003. We also modeled the second aftershock (Mw6.4) to asses geometric similarities during their respective rupture process. This aftershock occurred spatially very close to the mainshock and possesses a similar fault plane solution (strike=128, dip=71, rake=154), and centroid depth (13 km). Several local conditions, such as the crustal model and fault geometry, affect the correct estimation of some source parameters. We perfume a sensitivity evaluation of several parameters, including centroid depth, scalar moment and source duration, based on a point and finite source modeling. The point source approximation results are the departure parameters for the finite source exploration. We evaluate the different reported parameters to discard poor constrained models. In addition, deformation data acquired by InSAR are also included in the analysis.
Establishing repeatable operation of a centrifugal compressor research facility for aerodynamic investigations

NASA Astrophysics Data System (ADS)

Dolan, Matthew Philip

The objective of this research has been to analyze the steady state performance of a new centrifugal compressor research facility. The CSTAR (Centrifugal STage for Aerodynamic Research) compressor has been designed to be placed as the last stage in an axial compressor and its performance in this flow regime was measured. Because the compressor was designed as a research vehicle, unique instrumentation throughout the flow path provides a detailed look at its steady state performance. Rakes at the inlet and deswirl section quantify the overall performance but other instrumentation is used to understand the component performance. Static pressure taps along the shroud, within the diffuser, and through the turn-to-axial show the static pressure rise. Additionally, rakes at the inlet and exit of diffuser also characterize the performance of the wedge diffuser and the impeller. Additionally, capacitance probes located at the knee and exducer of the impeller non-intrusively measure the size of the tip clearance during facility operation. An investigation into these measurements resulted in a standard procedure for in-situ calibration and installation to produce repeatable and accurate clearance measurements. Finally, the feasibility of future Laser Doppler Velocimetry measurements acquired through the shroud window was tested and was found to be achievable with the use of beam translators to ensure that measurement volumes are created after beam refraction through the windows. Inlet conditions of the facility have been investigated and fluctuations of the ambient conditions have been mitigated with a large settling chamber to ensure repeatable and stable operation. The current instrumentation was utilized to determine the compressor performance. Measurements of the steady performance parameters along with those of the internal flowfield are documented.
Rock Abrasion Tool Exhibits the Deep Red Pigment of Mars

NASA Image and Video Library

2006-07-21

This image shows the round, metallic working end of the rock abrasion tool at the end of a metallic cylinder. The flat grinding face, attached brush, and much of the smooth, metallic exterior of cylinder are covered with a deep reddish-brown layer of dust
THE TWO FACES OF WATER CHEMISTRY: STRESSOR ON, AND INDICATOR OF, THE ECOLOGICAL CONDITION OF THE GREAT RIVERS.

EPA Science Inventory

This poster presentation is designed to enlighten the interested masses about water quality assessment tools. It is not intended for policy, rather to stimulate thought on the importance of developing water chemistry as as assessment tool.
Aspirations and Assumptions: A Researcher's Account of Pupil Involvement in School-Based Research

ERIC Educational Resources Information Center

Mearns, Tessa L.; Coyle, Do; de Graaff, Rick

2014-01-01

This paper describes a research project conducted in collaboration with 10 "pupil co-researchers" (PCRs) and their classes in a secondary school in the Netherlands. The main research tools employed were online and face-to-face group discussions, in which PCRs contributed as consultants, co-designers and assistants. The research proved a…
Transitioning from Traditional Courses to Technologically Supported Classrooms. IDEA Paper #62

ERIC Educational Resources Information Center

Proctor, Janice; Bumgardner, Tiffany

2016-01-01

This paper focuses on the authors' experiences teaching on Ohio University's Learning Network (OULN), which uses interactive television and real-time face-to-face interaction as a distance-education (DE) delivery tool. One of the authors is a sociology professor, and the other is her former student and an experienced OULN system operator. The…
Establishing an Empirical Link between Computer-Mediated Communication (CMC) and SLA: A Meta-Analysis of the Research

ERIC Educational Resources Information Center

Lin, Huifen

2014-01-01

Drawing on interactionist and socio-cultural theories, tools provided in computer-mediated communication (CMC) environments have long been considered able to create an environment that shares many communicative features with face-to-face communication. Over the past two decades, researchers have employed a variety of strategies to examine the…

Using Clickers for Deliberate Practice in Five Large Science Courses

ERIC Educational Resources Information Center

Hodges, Linda C.; Anderson, Eric C.; Carpenter, Tara S.; Cui, Lili; Feeser, Elizabeth A.; Gierasch, Tiffany Malinky

2017-01-01

Clickers are often used as an active learning tool in face-to-face classes to enhance student engagement and assess student learning. In this article we share the variety of ways that we use clicker questions to promote deliberate practice in large science courses. Deliberate practice is the use of specifically structured exercises that develop…
A comparison of sampling methods for a standing tree acoustic device

Treesearch

Jerry M. Mahon, Jr.; Lewis Jordan; Lawrence R. Schimleck; Alexander Clark, III; Richard F. Daniels

2009-01-01

One method of evaluating potential product performance is the use of acoustic tools for identifying trees with high stiffness. Acoustic velocities for 100 standing loblolly pine (Pinus taeda) trees, obtained with the transmitting and receiving probes placed on the same face and opposite faces, were compared. Significant differences in velocity between the two...
Preparing ESOL Teachers Using Web-Based Learning: Strategies and Tactics.

ERIC Educational Resources Information Center

Vazquez-Montilla, Elia; Zhu, Erping

Communications technologies such as Web-based conferencing and chat are being used increasingly around the world by instructors and students in either face to face or distance learning courses. While some discuss the affects of this phenomena, others are more focused on how these technological tools can be used in specific courses to achieve…
Peer Observation, Feedback and Reflection for Development of Practice in Synchronous Online Teaching

ERIC Educational Resources Information Center

Jones, Mark H.; Gallen, Anne-Marie

2016-01-01

Peer observation of teaching is an established developmental tool in face-to-face settings. While there have been studies into peer observation as applied to asynchronous online teaching, less is known about its application to teaching online using synchronous communication systems. We describe a small-scale study of an online peer observation…
Administering Examinations for Quality Control in Distance Education: The National Open University of Nigeria Perspective

ERIC Educational Resources Information Center

Ibara, E. C.

2008-01-01

Examination is an important tool for evaluating students learning outcome and require proper planning to meet high standards. This paper therefore examines the processes leading to administration of face-to-face examination in distance education with focus on the National Open University of Nigeria. It highlighted some procedures such as test…
Is Your Avatar Ethical? On-Line Course Tools that Are Methods for Student Identity and Verification

ERIC Educational Resources Information Center

Semple, Mid; Hatala, Jeffrey; Franks, Patricia; Rossi, Margherita A.

2011-01-01

On-line college courses present a mandate for student identity verification for accreditation and funding sources. Student authentication requires course modification to detect fraud and misrepresentation of authorship in assignment submissions. The reality is that some college students cheat in face-to-face classrooms; however, the potential for…
Strategies for Accommodating Extension Clients Who Face Language, Vision, or Hearing Challenges

ERIC Educational Resources Information Center

Angima, Sam; Etuk, Lena; Maddy, Deborah

2016-01-01

Extension services nationwide seek to equalize access to university resources for all learners. In this article, we focus on accommodation as a tool of our trade. We discuss findings and implications from a study that documented approaches used by one state's Extension professionals to accommodate clients who face language, vision, or hearing…
Quick and Easy: Use Screen Capture Software to Train and Communicate

ERIC Educational Resources Information Center

Schuster, Ellen

2011-01-01

Screen capture (screen cast) software can be used to develop short videos for training purposes. Developing videos is quick and easy. This article describes how these videos are used as tools to reinforce face-to-face and interactive TV curriculum training in a nutrition education program. Advantages of developing these videos are shared.…
A Formative Evaluation of WIKI's as a Learning Tool in a Face to Face Juvenile Justice Course

ERIC Educational Resources Information Center

Bowman, Scott Wm.

2013-01-01

Current literature indicates an increased pedagogical value of technology integration in university coursework. One form of technology that encourages collaborative, online teaching and learning is a "wiki," an online application that allows participants to partner and direct a website. This article describes the design and formative evaluation of…
Designing a Self-Contained Group Area Network for Ubiquitous Learning

ERIC Educational Resources Information Center

Chen, Nian-Shing; Kinshuk; Wei, Chun-Wang; Yang, Stephen J. H.

2008-01-01

A number of studies have evidenced that handheld devices are appropriate tools to facilitate face-to-face collaborative learning effectively because of the possibility of ample social interactions. Group Area Network, or GroupNet, proposed in this paper, uses handheld devices to fill the gap between Local Area Network and Body Area Network.…
Database Design Learning: A Project-Based Approach Organized through a Course Management System

ERIC Educational Resources Information Center

Dominguez, Cesar; Jaime, Arturo

2010-01-01

This paper describes an active method for database design learning through practical tasks development by student teams in a face-to-face course. This method integrates project-based learning, and project management techniques and tools. Some scaffolding is provided at the beginning that forms a skeleton that adapts to a great variety of…
Theory of Mind Enhances Preference for Fairness

ERIC Educational Resources Information Center

Takagishi, Haruto; Kameshima, Shinya; Schug, Joanna; Koizumi, Michiko; Yamagishi, Toshio

2010-01-01

The purpose of the current study was to examine the role of theory of mind in fairness-related behavior in preschoolers and to introduce a tool for examining fairness-related behavior in children. A total of 68 preschoolers played the Ultimatum Game in a face-to-face setting. Acquisition of theory of mind was defined as the understanding of false…
Applying CASE Tools for On-Board Software Development

NASA Astrophysics Data System (ADS)

Brammer, U.; Hönle, A.

For many space projects the software development is facing great pressure with respect to quality, costs and schedule. One way to cope with these challenges is the application of CASE tools for automatic generation of code and documentation. This paper describes two CASE tools: Rhapsody (I-Logix) featuring UML and ISG (BSSE) that provides modeling of finite state machines. Both tools have been used at Kayser-Threde in different space projects for the development of on-board software. The tools are discussed with regard to the full software development cycle.
Can We Talk through a Robot As if Face-to-Face? Long-Term Fieldwork Using Teleoperated Robot for Seniors with Alzheimer's Disease.

PubMed

Kuwamura, Kaiko; Nishio, Shuichi; Sato, Shinichi

2016-01-01

This work presents a case study on fieldwork in a group home for the elderly with dementia using a teleoperated robot called Telenoid. We compared Telenoid-mediated and face-to-face conditions with three residents with Alzheimer's disease (AD). The result indicates that two of the three residents with moderate AD showed a positive reaction to Telenoid. Both became less nervous while communicating with Telenoid from the time they were first introduced to it. Moreover, they started to use more body gestures in the face-to-face condition and more physical interactions in the Telenoid-mediated condition. In this work, we present all the results and discuss the possibilities of using Telenoid as a tool to provide opportunities for seniors to communicate over the long term.
Assessing the safety culture of care homes: a multimethod evaluation of the adaptation, face validity and feasibility of the Manchester Patient Safety Framework.

PubMed

Marshall, Martin; Cruickshank, Lesley; Shand, Jenny; Perry, Sarah; Anderson, James; Wei, Li; Parker, Dianne; de Silva, Debra

2017-09-01

Understanding the cultural characteristics of healthcare organisations is widely recognised to be an important component of patient safety. A growing number of vulnerable older people are living in care homes but little attention has been paid to safety culture in this sector. In this study, we aimed to adapt the Manchester Patient Safety Framework (MaPSaF), a commonly used tool in the health sector, for use in care homes and then to test its face validity and preliminary feasibility as a tool for developing a better understanding of safety culture in the sector. As part of a wider improvement programme to reduce the prevalence of common safety incidents among residents in 90 care homes in England, we adapted MaPSaF and carried out a multimethod participatory evaluation of its face validity and feasibility for care home staff. Data were collected using participant observation, interviews, documentary analysis and a survey, and were analysed thematically. MaPSaF required considerable adaptation in terms of its length, language and content in order for it to be perceived to be acceptable and useful to care home staff. The changes made reflected differences between the health and care home sectors in terms of the local context and wider policy environment, and the expectations, capacity and capabilities of the staff. Based on this preliminary study, the adapted tool, renamed 'Culture is Key', appears to have reasonable face validity and, with adequate facilitation, it is usable by front-line staff and useful in raising their awareness about safety issues. 'Culture is Key' is a new tool which appears to have acceptable face validity and feasibility to be used by care home staff to deepen their understanding of the safety culture of their organisations and therefore has potential to contribute to improving care for vulnerable older people. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.
Tool simplifies machining of pipe ends for precision welding

NASA Technical Reports Server (NTRS)

Matus, S. T.

1969-01-01

Single tool prepares a pipe end for precision welding by simultaneously performing internal machining, end facing, and bevel cutting to specification standards. The machining operation requires only one milling adjustment, can be performed quickly, and produces the high quality pipe-end configurations required to ensure precision-welded joints.
Overview of EPA tools for supporting local- and regional-scale decision makers addressing energy and environmental issues

EPA Science Inventory

EPA’s Office of Research and Development (ORD) has been developing tools and illustrative case studies for decision makers in local and regional authorities who are facing challenges of establishing resilience to extreme weather events, aging built environment and infrastru...
End of Asset Life Reinvestment Decision Support Tool (INFR2R11AT)

EPA Science Inventory

This “End of Asset Life” Reinvestment Decision-Support Tool is intended as a step by step guide for the asset management practitioner who faces the challenge of developing an investment strategy that represents the best integration of maintenance, operations, and capital investme...
Network-Centric Data Mining for Medical Applications

ERIC Educational Resources Information Center

Davis, Darcy A.

2012-01-01

Faced with unsustainable costs and enormous amounts of under-utilized data, health care needs more efficient practices, research, and tools to harness the benefits of data. These methods create a feedback loop where computational tools guide and facilitate research, leading to improved biological knowledge and clinical standards, which will in…
Collection Development in Public Health: A Guide to Selection Tools

ERIC Educational Resources Information Center

Wallis, Lisa C.

2004-01-01

Public health librarians face many challenges in collection development because the field is multidisciplinary, the collection's users have varied needs, and many of the essential resources are grey literature materials. Further, little has been published about public health selection tools. However, librarians responsible for these areas have a…

Development and Classroom Implementation of an Environmental Data Creation and Sharing Tool

ERIC Educational Resources Information Center

Brogan, Daniel S.; McDonald, Walter M.; Lohani, Vinod K.; Dymond, Randel L.; Bradner, Aaron J.

2016-01-01

Education is essential for solving the complex water-related challenges facing society. The Learning Enhanced Watershed Assessment System (LEWAS) and the Online Watershed Learning System (OWLS) provide data creation and data sharing infrastructures, respectively, that combine to form an environmental learning tool. This system collects, integrates…
Wonder as a Tool to Engage Preservice Elementary Teachers in Science Learning and Teaching

ERIC Educational Resources Information Center

Gilbert, Andrew; Byers, Christie C.

2017-01-01

This exploratory project considers the use of "wonder" as a pedagogical tool with preservice elementary teachers (PSETs). An ongoing vexation facing science teacher educators is helping future elementary teachers overcome anxiety and negative associations with science due to their own school science experiences, while simultaneously…
Private Education as a Policy Tool in Turkey

ERIC Educational Resources Information Center

Cinoglu, Mustafa

2006-01-01

This paper discusses privatization as policy tool to solve educational problems in Turkey. Turkey, as a developing country, is faced with many problems in education. Large class size, low enrollment rate, girl's education, high illiteracy rate, religious education, textbooks, curriculum and multicultural education are some of the important…
Software management tools: Lessons learned from use

NASA Technical Reports Server (NTRS)

Reifer, D. J.; Valett, J.; Knight, J.; Wenneson, G.

1985-01-01

Experience in inserting software project planning tools into more than 100 projects producing mission critical software are discussed. The problems the software project manager faces are listed along with methods and tools available to handle them. Experience is reported with the Project Manager's Workstation (PMW) and the SoftCost-R cost estimating package. Finally, the results of a survey, which looked at what could be done in the future to overcome the problems experienced and build a set of truly useful tools, are presented.
Judgments at Gaze Value: Gaze Cuing in Banner Advertisements, Its Effect on Attention Allocation and Product Judgments.

PubMed

Palcu, Johanna; Sudkamp, Jennifer; Florack, Arnd

2017-01-01

Banner advertising is a popular means of promoting products and brands online. Although banner advertisements are often designed to be particularly attention grabbing, they frequently go unnoticed. Applying an eye-tracking procedure, the present research aimed to (a) determine whether presenting human faces (static or animated) in banner advertisements is an adequate tool for capturing consumers' attention and thus overcoming the frequently observed phenomenon of banner blindness, (b) to examine whether the gaze of a featured face possesses the ability to direct consumers' attention toward specific elements (i.e., the product) in an advertisement, and (c) to establish whether the gaze direction of an advertised face influences consumers subsequent evaluation of the advertised product. We recorded participants' eye gaze while they viewed a fictional online shopping page displaying banner advertisements that featured either no human face or a human face that was either static or animated and involved different gaze directions (toward or away from the advertised product). Moreover, we asked participants to subsequently evaluate a set of products, one of which was the product previously featured in the banner advertisement. Results showed that, when advertisements included a human face, participants' attention was more attracted by and they looked longer at animated compared with static banner advertisements. Moreover, when a face gazed toward the product region, participants' likelihood of looking at the advertised product increased regardless of whether the face was animated or not. Most important, gaze direction influenced subsequent product evaluations; that is, consumers indicated a higher intention to buy a product when it was previously presented in a banner advertisement that featured a face that gazed toward the product. The results suggest that while animation in banner advertising constitutes a salient feature that captures consumers' visual attention, gaze cuing can be an effective tool for driving viewers' attention toward specific elements in the advertisement and even shaping consumers' intentions to purchase the advertised product.
Judgments at Gaze Value: Gaze Cuing in Banner Advertisements, Its Effect on Attention Allocation and Product Judgments

PubMed Central

Palcu, Johanna; Sudkamp, Jennifer; Florack, Arnd

2017-01-01

Banner advertising is a popular means of promoting products and brands online. Although banner advertisements are often designed to be particularly attention grabbing, they frequently go unnoticed. Applying an eye-tracking procedure, the present research aimed to (a) determine whether presenting human faces (static or animated) in banner advertisements is an adequate tool for capturing consumers’ attention and thus overcoming the frequently observed phenomenon of banner blindness, (b) to examine whether the gaze of a featured face possesses the ability to direct consumers’ attention toward specific elements (i.e., the product) in an advertisement, and (c) to establish whether the gaze direction of an advertised face influences consumers subsequent evaluation of the advertised product. We recorded participants’ eye gaze while they viewed a fictional online shopping page displaying banner advertisements that featured either no human face or a human face that was either static or animated and involved different gaze directions (toward or away from the advertised product). Moreover, we asked participants to subsequently evaluate a set of products, one of which was the product previously featured in the banner advertisement. Results showed that, when advertisements included a human face, participants’ attention was more attracted by and they looked longer at animated compared with static banner advertisements. Moreover, when a face gazed toward the product region, participants’ likelihood of looking at the advertised product increased regardless of whether the face was animated or not. Most important, gaze direction influenced subsequent product evaluations; that is, consumers indicated a higher intention to buy a product when it was previously presented in a banner advertisement that featured a face that gazed toward the product. The results suggest that while animation in banner advertising constitutes a salient feature that captures consumers’ visual attention, gaze cuing can be an effective tool for driving viewers’ attention toward specific elements in the advertisement and even shaping consumers’ intentions to purchase the advertised product. PMID:28626436
Astronaut John Young collecting samples at North Ray crater during EVA

NASA Image and Video Library

1972-04-23

AS16-117-18826 (23 April 1972) --- Astronaut John W. Young collects samples at the North Ray Crater geological site during the mission's third and final Apollo 16 extravehicular activity (EVA). He has a rake in his hand, and the gnomon is near his foot. Note how soiled Young's Extravehicular Mobility Unit (EMU) is. While astronauts Young, commander; and Charles M. Duke Jr., lunar module pilot; descended in the Apollo 16 Lunar Module (LM) "Orion" to explore the Descartes highlands landing site on the moon, astronaut Thomas K. Mattingly II, command module pilot, remained with the Command and Service Modules (CSM) "Casper" in lunar orbit.
Optical Cryogenic Tank Level Sensor

NASA Technical Reports Server (NTRS)

Duffell, Amanda

2005-01-01

Cryogenic fluids play an important role in space transportation. Liquid oxygen and hydrogen are vital fuel components for liquid rocket engines. It is also difficult to accurately measure the liquid level in the cryogenic tanks containing the liquids. The current methods use thermocouple rakes, floats, or sonic meters to measure tank level. Thermocouples have problems examining the boundary between the boiling liquid and the gas inside the tanks. They are also slow to respond to temperature changes. Sonic meters need to be mounted inside the tank, but still above the liquid level. This causes problems for full tanks, or tanks that are being rotated to lie on their side.
Sidewall Mach Number Distributions for the NASA Langley Transonic Dynamics Tunnel

NASA Technical Reports Server (NTRS)

Florance, James R.; Rivera, Jose A., Jr.

2001-01-01

The Transonic Dynamics Tunnel(TDT) was recalibrated due to the conversion of the heavy gas test medium from R-12 to R-134a. The objectives of the tests were to determine the relationship between the free-stream Mach number and the measured test section Mach number, and to quantify any necessary corrections. Other tests included the measurement of pressure distributions along the test-section walls, test-section centerline, at certain tunnel stations via a rake apparatus, and in the tunnel settling chamber. Wall boundary layer, turbulence, and flow angularity measurements were also performed. This paper discusses the determination of sidewall Mach number distributions.
Study of the Effects of Centrifugal Instabilities on Flow in a 40 to 1 Aspect Ratio Rectangular Curved Channel, for Dean Numbers from 35 to Fully Turbulent Conditions

DTIC Science & Technology

1990-12-01

is constructed from stainless steel hypodermic tubing with inner and outer diameters of 0.203 mm and 0.406 mm. The five tubes were first joined by...for all channels is 256 kHz. A schematic diagram of the measurement process [Ref. 25] is given in Figure 78, and is also described below. The analog...and smoke rake. Combustion takes place inside a 40.64 cm long, 6.27 cm inside diameter (2.5 inch schedule 40) steel pipe. Inside this chamber, smoke is
Computations and turbulent flow modeling in support of helicopter rotor technology

NASA Technical Reports Server (NTRS)

Rose, W. C.

1985-01-01

The angle of attack (AOA) tandem cavity wind tunnel experiment was prepared. Actual wind tunnel testing started shortly after the beginning of 1985. A multi-probe aerodynamic rake was designed and installed for use in surveying the shear layers present over the open cavity on the Kuiper Airborne Observatory (KAO). The nature of the behavior of the thermal environment within the KAO cavity at operational altitudes was determined. Assistance was given in the design of the cavity for the University of Denver radiometer. Attempts to distinguish between the optical terms of blur circle size (or image size) and the term due to jitter were discussed.
Techniques used in the F-14 variable-sweep transition flight experiment

NASA Technical Reports Server (NTRS)

Anderson, Bianca Trujillo; Meyer, Robert R., Jr.; Chiles, Harry R.

1988-01-01

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system; (2) two boundary-layer rakes; (3) surface pitot tubes; and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.
Disk Rock Cutting Tool for the Implementation of Resource-Saving Technologies of Mining of Solid Minerals

NASA Astrophysics Data System (ADS)

Manietyev, Leonid; Khoreshok, Aleksey; Tsekhin, Alexander; Borisov, Andrey

2017-11-01

The directions of a resource and energy saving when creating a boom-type effectors of roadheaders of selective action with disc rock cutting tools on a multi-faceted prisms for the destruction of formation of minerals and rocks pricemax are presented. Justified reversing the modes of the crowns and booms to improve the efficiency of mining works. Parameters of destruction of coal and rock faces by the disk tool of a biconical design with the unified fastening knots to many-sided prisms on effectors of extraction mining machines are determined. Parameters of tension of the interfaced elements of knots of fastening of the disk tool at static interaction with the destroyed face of rocks are set. The technical solutions containing the constructive and kinematic communications realizing counter and reverse mode of rotation of two radial crowns with the disk tool on trihedral prisms and cases of booms with the disk tool on tetrahedral prisms in internal space between two axial crowns with the cutter are proposed. Reserves of expansion of the front of loading outside a table of a feeder of the roadheader of selective action, including side zones in which loading corridors by blades of trihedral prisms in internal space between two radial crowns are created are revealed.
Face and Content Validity of the MacArthur Competence Assessment Tool for the Treatment of Iranian Patients.

PubMed

Saber, Ali; Tabatabaei, Seyed Mahmoud; Akasheh, Godarz; Sehat, Mojtaba; Zanjani, Zahra; Larijani, Bagher

2017-01-01

There is not a valid Persian tool for measuring the decision-making competency of patients. The aim of this study is to evaluate the face and content validity of the MacArthur Competence Assessment Tool for the treatment of Iranian Persian-speaking patients. To assess the validity of the Persian version of the tool, a self-administrated questionnaire was designed. The Lawshe method was also used for assessing each item. Content validity ratio (CVR) and content validity index (CVI) were used to assess the content validity quantitatively. According to the experts' judgment, questions with a CVR ≥0.62 and CVR <0.62 were maintainable and unmaintainable, respectively. The questions were designed in a manner to achieve the desirable result (CVR ≥0.62). The CVI scale (S-CVI) and CVI (S-CVI/Ave) were 0.94 (higher than 0.79). Thus, the content validity was confirmed. Since capacity assessments are usually based on physician's subjective judgment, they are likely to bias and therefore, with this suitably validated tool, we can improve judgment of physicians and health-care providers in out- and in-patient cases.
A tool for exploring the dynamics of innovative interventions for public health: the critical event card.

PubMed

Figueiro, Ana Claudia; de Araújo Oliveira, Sydia Rosana; Hartz, Zulmira; Couturier, Yves; Bernier, Jocelyne; do Socorro Machado Freire, Maria; Samico, Isabella; Medina, Maria Guadalupe; de Sa, Ronice Franco; Potvin, Louise

2017-03-01

Public health interventions are increasingly represented as complex systems. Research tools for capturing the dynamic of interventions processes, however, are practically non-existent. This paper describes the development and proof of concept process of an analytical tool, the critical event card (CEC), which supports the representation and analysis of complex interventions' evolution, based on critical events. Drawing on the actor-network theory (ANT), we developed and field-tested the tool using three innovative health interventions in northeastern Brazil. Interventions were aimed to promote health equity through intersectoral approaches; were engaged in participatory evaluation and linked to professional training programs. The CEC developing involve practitioners and researchers from projects. Proof of concept was based on document analysis, face-to-face interviews and focus groups. Analytical categories from CEC allow identifying and describing critical events as milestones in the evolution of complex interventions. Categories are (1) event description; (2) actants (human and non-human) involved; (3) interactions between actants; (4) mediations performed; (5) actions performed; (6) inscriptions produced; and (7) consequences for interventions. The CEC provides a tool to analyze and represent intersectoral internvetions' complex and dynamic evolution.
A Cross-Sectional Descriptive Study of Graduate Students' Perceptions of Learning Effectiveness in Face-to-Face and Online Courses

ERIC Educational Resources Information Center

Evans, Nicole Stayton

2013-01-01

The measurement of student perceptions of learning effectiveness is often used as a tool at universities to enhance the quality of course offerings. The recent growth in online course offerings creates new challenges in evaluating learning effectiveness. This study used three principles of adult learning theory, foundation, self-concept, and…
The Use of Wiki in Teaching Programming: Effects upon Achievement, Attitudes, and Collaborative Programming Behaviors

ERIC Educational Resources Information Center

Lin, Yu-Tzu; Wu, Cheng-Chih; Chiu, Chiung-Fang

2018-01-01

This article explores the feasibility of employing cooperative program editing tools in teaching programming. A quasi-experimental study was conducted, in which the experimental group co-edited the programs with peers using the wiki. The control group co-edited the programs with peers using only the face-to-face approach. The findings show that…
Let's Connect: Using Adobe Connect to Foster Group Collaboration in the Online Classroom

ERIC Educational Resources Information Center

Kaufmann, Renee; Frisby, Brandi N.

2013-01-01

The need for students to become connected in the classroom parallels the need for students to become socially integrated into the college community. Because technological tools are always changing, the opportunity for all students on- and off-campus to ''meet'' face-to-face and build relationships within the classroom are…
Web-Based Lecture Technologies: Blurring the Boundaries between Face-to-Face and Distance Learning

ERIC Educational Resources Information Center

Woo, Karen; Gosper, Maree; McNeill, Margot; Preston, Greg; Green, David; Phillips, Rob

2008-01-01

Web-based lecture technologies (WBLT) have gained popularity amongst universities in Australia as a tool for delivering lecture recordings to students in close to real time. This paper reports on a selection of results from a larger research project investigating the impact of WBLT on teaching and learning. Results show that while staff see the…
Statistics? You Must Be Joking: The Application and Evaluation of Humor when Teaching Statistics

ERIC Educational Resources Information Center

Neumann, David L.; Hood, Michelle; Neumann, Michelle M.

2009-01-01

Humor has been promoted as a teaching tool that enhances student engagement and learning. The present report traces the pathway from research to practice by reflecting upon various ways to incorporate humor into the face-to-face teaching of statistics. The use of humor in an introductory university statistics course was evaluated via interviews…

The Impact of Wikis and Discussion Boards on Learning English as a Second Language. A Mixed Methods Research

ERIC Educational Resources Information Center

Sánchez-Gómez, Ma. Cruz; Pinto-Llorente, Ana Ma.; García-Peñalvo, Francisco José

2017-01-01

In the field of teaching a second language (L2), technology has always occupied a relevant position. The development of new technological tools has allowed the convergence of two learning environments, traditional face-to-face learning and virtual learning. This convergence has fostered the advantages of both types of instructions and the…
Brief Report: Telephone Administration of the Autism Diagnostic Interview-Revised--Reliability and Suitability for Use in Research

ERIC Educational Resources Information Center

Ward-King, Jessica; Cohen, Ira L.; Penning, Henderika; Holden, Jeanette J. A.

2010-01-01

The Autism Diagnostic Interview-Revised is one of the "gold standard" diagnostic tools for autism spectrum disorders. It is traditionally administered face-to-face. Cost and geographical concerns constrain the employment of the ADI-R for large-scale research projects. The telephone interview is a reasonable alternative, but has not yet been…
Incorporating Competency-Based Blended Learning in a Chinese Language Classroom: A Web 2.0 Drupal Module Design

ERIC Educational Resources Information Center

Huang, Chung-Kai; Lin, Chun-Yu; Chiang, Yueh-Hui

2010-01-01

This study aims to create a blended learning environment, based on the concept of competency-based training, in a Chinese as a Foreign Language (CFL) classroom at an American university. Drupal platform and web 2.0 tools were used as supplements to traditional face-to-face classroom instruction. Students completed various selective tasks and…
Effectiveness and Obstacle of Using Facebook as a Tool to Facilitate Student-Centred Learning in Higher Education

ERIC Educational Resources Information Center

Cheng, Irene Nga Yee; Chan, Janet Kit Yan; Kong, Suria Suet Yee; Leung, Kenneth Mei Yee

2016-01-01

Blended learning which combines face-to-face and online experiences of students by integrating technology into the curriculum is increasingly prevalent in university education. In a context of long time arguments on the educational value of using social networking websites on teaching and learning, this study was conducted in two higher education…
A Case Study of E-Tutors' Teaching Practice: Does Technology Drive Pedagogy?

ERIC Educational Resources Information Center

Chuang, Hsueh-Hua

2013-01-01

This article presents a case study of e-tutoring teaching practice during a 20-week e-tutoring program aimed at improving the English proficiency of targeted students. The study revealed what and why certain online tools were used by e-tutors and investigated how different technological proficiency and face-to-face (f2f) teaching experience shaped…
Physician recruitment websites: the territory ahead.

PubMed

DuPont, R E

2001-01-01

Recruitment is no longer just a face-to-face interaction between a recruiter and a job-seeker. To remain up-to-date with current technology, physicians should use the various electronic tools available today, including recruitment websites, video previews, and PC-to-PC interviews to get the job they've been looking for. This article discusses the pros and cons of these interfaces.
Analysis Matrix of Resilience in the Face of Disability, Old Age and Poverty

ERIC Educational Resources Information Center

Cardenas, Andrea; Lopez, Lucero

2010-01-01

The purpose of this article is to describe the process of the development of the "Resilience Theoretical Analysis Matrix" (RTAM) (or in its Spanish translation: MATR), a tool designed to facilitate a coherent and organised approach to the assessment of a wide spectrum of factors influencing the development of resilience in the face of disability,…
Face to face activation of a phenylselenium borane with α,β-unsaturated carbonyl substrates: facile synthesis of C-Se bonds.

PubMed

Sanz, Xavier; Vogels, Christopher M; Decken, Andreas; Bo, Carles; Westcott, Stephen A; Fernández, Elena

2014-08-07

Activated olefins directly react with a phenylselenium borane, at room temperature, without any metal or organocatalytic assistance. Up to 10 examples of β-(phenylseleno) substituted ketones and aldehydes have been prepared and theoretical evidence for the mechanism opens up non-existing pathways to create C-heteroatom bonds as a general tool.
Effects of Competitive E-Learning Tools on Higher Education Students: A Case Study

ERIC Educational Resources Information Center

Regueras, L. M.; Verdu, E.; Munoz, M. F.; Perez, M. A.; de Castro, J. P.; Verdu, M. J.

2009-01-01

Over the last few years, most of the attempts to introduce active learning methodologies in the classroom have made use of Information and Communication Technology (ICT). Many of these efforts have been directed to collaborative scenarios used in remote, blended or face-to-face experiences, in order to take advantage of the flexibility provided by…
Negotiation of Meaning as a Tool for Evaluating Conversational Skills in the OPI

ERIC Educational Resources Information Center

Kitajima, Ryu

2009-01-01

Though the oral proficiency interview (OPI) rates the examinee's overall language proficiency in face-to-face interaction, the rating is based solely upon the evaluation of the examinee's contribution in isolation. No attempt is made to evaluate conversational skills in interaction. A criticism that has been made of the OPI is that the format is…
The Usage Characteristics of Twitter in the Learning Process

ERIC Educational Resources Information Center

Cohen, Anat; Duchan, Galit

2012-01-01

This research discusses the use of Twitter as a teaching-supporting tool in face to face (F2F) learning. The uniqueness and importance of this research is in the age group on which it focuses, an age group that has not yet been examined (ninth grade); furthermore, data was analyzed by decoding tweets, grouping tweets into various pedagogical and…
Blended Learning: Understanding the Middle Ground between Traditional Classroom and Fully Online Instruction

ERIC Educational Resources Information Center

Welker, Jan; Berardino, Lisa

2006-01-01

Blended learning is any combined use of electronic learning tools that supplement but do not replace face-to-face learning. This article is about how two researchers are trying to comfortably and logically place blended learning somewhere in the middle of two extremes--traditional classroom at one end and fully online distance learning at the…
Evaluating Administrators with Portfolios: Principals Report Mostly Positive Experiences when Used as Part of a Performance Review

ERIC Educational Resources Information Center

Russo, Alexander

2004-01-01

Simple checklists, one-shot interviews, brief site visits and narrative evaluations remain widespread as the tools of assessment. In many school districts, the evaluation includes little or no face-to-face contact, and the principal simply gets his or her evaluation in the mail, leading one researcher to describe them as "infrequent, late,…
"Post It on the Wall!": Using Facebook to Complement Student Learning in Gender and Women's Studies Courses

ERIC Educational Resources Information Center

Alexander, Susan M.; Sapra, Sonalini

2013-01-01

College professors, including those in women's studies, are increasingly implementing pedagogical methods that include online social networking tools such as YouTube, Facebook, Friendster, Del.icio.us, blogs, etc., to enhance face-to-face discussions in the classroom. The sharing of up-to-the-minute information on a site that students are already…
A thin-plate spline analysis of the face and tongue in obstructive sleep apnea patients.

PubMed

Pae, E K; Lowe, A A; Fleetham, J A

1997-12-01

The shape characteristics of the face and tongue in obstructive sleep apnea (OSA) patients were investigated using thin-plate (TP) splines. A relatively new analytic tool, the TP spline method, provides a means of size normalization and image analysis. When shape is one's main concern, various sizes of a biologic structure may be a source of statistical noise. More seriously, the strong size effect could mask underlying, actual attributes of the disease. A set of size normalized data in the form of coordinates was generated from cephalograms of 80 male subjects. The TP spline method envisioned the differences in the shape of the face and tongue between OSA patients and nonapneic subjects and those between the upright and supine body positions. In accordance with OSA severity, the hyoid bone and the submental region positioned inferiorly and the fourth vertebra relocated posteriorly with respect to the mandible. This caused a fanlike configuration of the lower part of the face and neck in the sagittal plane in both upright and supine body positions. TP splines revealed tongue deformations caused by a body position change. Overall, the new morphometric tool adopted here was found to be viable in the analysis of morphologic changes.
The FaceBase Consortium: a comprehensive resource for craniofacial researchers

PubMed Central

Brinkley, James F.; Fisher, Shannon; Harris, Matthew P.; Holmes, Greg; Hooper, Joan E.; Wang Jabs, Ethylin; Jones, Kenneth L.; Kesselman, Carl; Klein, Ophir D.; Maas, Richard L.; Marazita, Mary L.; Selleri, Licia; Spritz, Richard A.; van Bakel, Harm; Visel, Axel; Williams, Trevor J.; Wysocka, Joanna

2016-01-01

The FaceBase Consortium, funded by the National Institute of Dental and Craniofacial Research, National Institutes of Health, is designed to accelerate understanding of craniofacial developmental biology by generating comprehensive data resources to empower the research community, exploring high-throughput technology, fostering new scientific collaborations among researchers and human/computer interactions, facilitating hypothesis-driven research and translating science into improved health care to benefit patients. The resources generated by the FaceBase projects include a number of dynamic imaging modalities, genome-wide association studies, software tools for analyzing human facial abnormalities, detailed phenotyping, anatomical and molecular atlases, global and specific gene expression patterns, and transcriptional profiling over the course of embryonic and postnatal development in animal models and humans. The integrated data visualization tools, faceted search infrastructure, and curation provided by the FaceBase Hub offer flexible and intuitive ways to interact with these multidisciplinary data. In parallel, the datasets also offer unique opportunities for new collaborations and training for researchers coming into the field of craniofacial studies. Here, we highlight the focus of each spoke project and the integration of datasets contributed by the spokes to facilitate craniofacial research. PMID:27287806
Search optimization of named entities from twitter streams

NASA Astrophysics Data System (ADS)

Fazeel, K. Mohammed; Hassan Mottur, Simama; Norman, Jasmine; Mangayarkarasi, R.

2017-11-01

With Enormous number of tweets, People often face difficulty to get exact information about those tweets. One of the approach followed for getting information about those tweets via Google. There is not any accuracy tool developed for search optimization and as well as getting information about those tweets. So, this system contains the search optimization and functionalities for getting information about those tweets. Another problem faced here are the tweets that contains grammatical errors, misspellings, non-standard abbreviations, and meaningless capitalization. So, these problems can be eliminated by the use of this tool. Lot of time can be saved and as well as by the use of efficient search optimization each information about those particular tweets can be obtained.
Solutions to Challenges Facing a University Digital Library and Press

PubMed Central

D'Alessandro, Michael P.; Galvin, Jeffrey R.; Colbert, Stephana I.; D'Alessandro, Donna M.; Choi, Teresa A.; Aker, Brian D.; Carlson, William S.; Pelzer, Gay D.

2000-01-01

During the creation of a university digital library and press intended to serve as a medical reference and education tool for health care providers and their patients, six distinct and complex digital publishing challenges were encountered. Over nine years, through a multidisciplinary approach, solutions were devised to the challenges of digital content ownership, management, mirroring, translation, interactions with users, and archiving. The result is a unique, author-owned, internationally mirrored, university digital library and press that serves as an authoritative medical reference and education tool for users around the world. The purpose of this paper is to share the valuable digital publishing lessons learned and outline the challenges facing university digital libraries and presses. PMID:10833161
Football Face-Mask Removal With a Cordless Screwdriver on Helmets Used for at Least One Season of Play

PubMed Central

Decoster, Laura C; Shirley, Chandra P; Swartz, Erik E

2005-01-01

Context: The Inter-Association Task Force for the Appropriate Care of the Spine-Injured Athlete recommends leaving a football player's helmet in place and removing the face mask from the helmet “as quickly as possible and with as little movement of the head and neck as possible.” Although 2 groups have studied face-mask removal from new equipment, to our knowledge no researchers have investigated equipment that has been previously used. A full season of play may have a significant effect on football equipment and its associated hardware. Countless impacts, weather, playing surfaces, sweat, and other unforeseen or unknown variables might make the face-mask removal process more difficult on equipment that has been used. Objective: To determine the percentage of face masks that we could unscrew, with a cordless screwdriver, from football helmets used for a full season. Design: Cross-sectional. Setting: Three New England high schools. Patients or Other Participants: All football helmets used at 3 local high schools were tested (n = 222, mean games, 9.7 ± 1.2; mean practice weeks, 13.7 ± 1.2). Intervention(s): Each helmet was secured to a board, and a cordless screwdriver was used to attempt to remove all 4 screws attaching the face mask to the helmet. Main Outcome Measure(s): Variables included overall success or failure, time required for face-mask removal, and success by screw location. Data were analyzed with χ2, analysis of variance, and Tamhane post hoc tests. Results: Overall, 832 (94%) of 885 screws were unscrewed, and 183 (82.4%) of 222 face masks were removed. Mean removal time was 26.9 ± 5.83 seconds. Face-mask removal success was significantly different between school 1 (24 [52.2%] of 46) and schools 2 (84 [91.3%] of 92) and 3 (75 [89.3%] of 84; F2,219 = 24.608; P < .001). The removal success rate was significantly higher at top screws (98%) than at screws adjacent to ear holes (90%) (P < .001). Conclusions: Based on our results and previous findings that demonstrated quicker access time and reduced head movement associated with the use of the screwdriver compared with cutting tools, the former may be a good tool for face-mask removal. However, an appropriate cutting tool must be immediately available should the screwdriver fail. Helmet hardware adjacent to ear holes was more vulnerable to failure, perhaps because it is protected by less padding than the top hardware. Possible causes of the higher failure rate at school 1 are the use of hardware materials subject to rust and corrosion and differences in helmet brand; these areas warrant future research and rules consideration. PMID:16284636
Development and Deployment of an Aerospace Recommended Practice (ARP) Compliant Measurement System for nvPM Certification Measurements of Aircraft Engines - Current Status.

NASA Astrophysics Data System (ADS)

Whitefield, P. D.; Hagen, D. E.; Lobo, P.; Miake-Lye, R. C.

2015-12-01

The Society of Automotive Engineers (SAE) Aircraft Exhaust Emissions Measurement Committee (E-31) has published an Aerospace Information Report (AIR) 6241 detailing the sampling system for the measurement of non-volatile particulate matter (nvPM) from aircraft engines (SAE 2013). The system is designed to operate in parallel with existing International Civil Aviation Organization (ICAO) Annex 16 compliant combustion gas sampling systems used for emissions certification from aircraft engines captured by conventional (Annex 16) gas sampling rakes (ICAO, 2008). The SAE E-31 committee is also working to ballot an Aerospace Recommended Practice (ARP) that will provide the methodology and system specification to measure nvPM from aircraft engines. The ARP is currently in preparation and is expected to be ready for ballot in 2015. A prototype AIR-compliant nvPM measurement system - The North American Reference System (NARS) has been built and evaluated at the MSTCOE under the joint sponsorship of the FAA, EPA and Transport Canada. It has been used to validate the performance characteristics of OEM AIR-compliant systems and is being used in engine certification type testing at OEM facilities to obtain data from a set of representative engines in the fleet. The data collected during these tests will be used by ICAO/CAEP/WG3/PMTG to develop a metric on which on the regulation for nvPM emissions will be based. This paper will review the salient features of the NARS including: (1) emissions sample transport from probe tip to the key diagnostic tools, (2) the mass and number-based diagnostic tools for nvPM mass and number concentration measurement and (3) methods employed to assess the extent of nvPM loss throughout the sampling system. This paper will conclude with a discussion of the recent results from inter-comparison studies conducted with other US - based systems that gives credence to the ARP's readiness for ballot.

The material performance of HSS (high speed steel) tools and its relation with chemical composition and carbide distribution

NASA Astrophysics Data System (ADS)

Darmawan, B.; Kusman, M.; Hamdani, R. A.

2016-04-01

The study aims to compare the performance of two types of material HSS (High Speed Steel) are widely used. It also will be the chemical composition and distribution of carbide particles therein. Two types of HSS are available in the market: HSS from Germany (Bohler) and HSS from China. This research employed the pure experimental design. It consists of two stages. The first, aims to test/operate lathe machines to determine the lifetime and performance of tools based on specified wear criteria. The second, characterization of microstructure using SEM-EDS was conducted. Firstly, grinding of toolss was done so that the toolss could be used for cutting metal in the turning process. Grinding processes of the two types of toolss were done at the same geometry, that is side rake angle (12°-18°), angle of keenness (60°-68°), and side relief angle (10°-12°). Likewise, machining parameters were set in the same machining conditions. Based on the results of the tests, it is found that to reach 0.2 mm wear point, toolss made of HSS from Germany needed 24 minutes, while toolss made of HSS from China needed 8 minutes. Next, microstructure tests using SEM/EDS were done. The results of the SEM tests indicate that the carbide particles of HSS from Germany were more evenly distributed than the carbide particles of HSS from China. Carbide compounds identified in HSS from China were Cr23C6 and Fe4Mo2C. Oxide impurity of Al2O3 was also found in the material. On the other hand, in HSS from Germany, no impurity and other carbide compounds were identified, except Cr23C6 and Fe4Mo2C, also Fe4W2C, and VC or V4C3.
Perioperative Care Coordination Measurement: A Tool to Support Care Integration of Pediatric Surgical Patients.

PubMed

Ferrari, Lynne R; Ziniel, Sonja I; Antonelli, Richard C

2016-03-01

The relationship of care coordination activities and outcomes to resource utilization and personnel costs has been evaluated for a number of pediatric medical home practices. One of the first tools designed to evaluate the activities and outcomes for pediatric care coordination is the Care Coordination Measurement Tool (CCMT). It has become widely used as an instrument for health care providers in both primary and subspecialty care settings. This tool enables the user to stratify patients based on acuity and complexity while documenting the activities and outcomes of care coordination. We tested the feasibility of adapting the CCMT to a pediatric surgical population at Boston Children's Hospital. The tool was used to assess the preoperative care coordination activities. Care coordination activities were tracked during the interval from the date the patient was scheduled for a surgical or interventional procedure through the day of the procedure. A care coordination encounter was defined as any task, whether face to face or not, supporting the development or implementation of a plan of care. Data were collected to enable analysis of 5675 care coordination encounters supporting the care provided to 3406 individual surgical cases (patients). The outcomes of care coordination, as documented by the preoperative nursing staff, included the elaboration of the care plan through patient-focused communication among specialist, facilities, perioperative team, and primary care physicians in 80.5% of cases. The average time spent on care coordination activities increased incrementally by 30 minutes with each additional care coordination encounter for a surgical case. Surgical cases with 1 care coordination encounter took an average of 35.7 minutes of preoperative care coordination, whereas those with ≥4 care coordination encounters reported an average of 121.6 minutes. We successfully adapted and implemented the CCMT for a pediatric surgical population and measured nonface-to-face, nonbillable encounters performed by perioperative nursing staff. The care coordination activities integrated into the preoperative process include elaboration of care plans and identification and remediation of discrepancies. Capturing the activities and outcomes of care coordination for preoperative care provides a framework for quality improvement and enables documentation of the value of nonface-to-face perioperative nursing encounters that comprise care coordination.
Development of three-dimensional patient face model that enables real-time collision detection and cutting operation for a dental simulator.

PubMed

Yamaguchi, Satoshi; Yamada, Yuya; Yoshida, Yoshinori; Noborio, Hiroshi; Imazato, Satoshi

2012-01-01

The virtual reality (VR) simulator is a useful tool to develop dental hand skill. However, VR simulations with reactions of patients have limited computational time to reproduce a face model. Our aim was to develop a patient face model that enables real-time collision detection and cutting operation by using stereolithography (STL) and deterministic finite automaton (DFA) data files. We evaluated dependence of computational cost and constructed the patient face model using the optimum condition for combining STL and DFA data files, and assessed the computational costs for operation in do-nothing, collision, cutting, and combination of collision and cutting. The face model was successfully constructed with low computational costs of 11.3, 18.3, 30.3, and 33.5 ms for do-nothing, collision, cutting, and collision and cutting, respectively. The patient face model could be useful for developing dental hand skill with VR.
Extraction and fusion of spectral parameters for face recognition

NASA Astrophysics Data System (ADS)

Boisier, B.; Billiot, B.; Abdessalem, Z.; Gouton, P.; Hardeberg, J. Y.

2011-03-01

Many methods have been developed in image processing for face recognition, especially in recent years with the increase of biometric technologies. However, most of these techniques are used on grayscale images acquired in the visible range of the electromagnetic spectrum. The aims of our study are to improve existing tools and to develop new methods for face recognition. The techniques used take advantage of the different spectral ranges, the visible, optical infrared and thermal infrared, by either combining them or analyzing them separately in order to extract the most appropriate information for face recognition. We also verify the consistency of several keypoints extraction techniques in the Near Infrared (NIR) and in the Visible Spectrum.
Confined Tube Crimp Using Portable Hand Tools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reynolds, Joseph James; Pereyra, R. A.; Archuleta, Jeffrey Christopher

2016-04-04

The Lawrence Radiation Laboratory developed handheld tools that crimp a 1/16 inch OD tube, forming a leak tight seal1 (see Figure 1). The leak tight seal forms by confining the 1/16 inch OD tubing inside a die while applying crimp pressure. Under confined pressure, the tube walls weld at the crimp. The purpose of this study was to determine conditions for fabricating a leak tight tube weld. The equipment was used on a trial-and-error basis, changing the conditions after each attempt until successful welds were fabricated. To better confine the tube, the die faces were polished. Polishing removed a fewmore » thousandths of an inch from the die face, resulting in a tighter grip on the tubing wall. Using detergent in an ultrasonic bath, the tubing was cleaned. Also, the time under crimp pressure was increased to 30 seconds. With these modifications, acceptable cold welds were fabricated. After setting the conditions for an acceptable cold weld, the tube was TIG welded across the crimped face.« less
An Evaluation of the Predictive Validity of Confidence Ratings in Identifying Functional Behavioral Assessment Hypothesis Statements

ERIC Educational Resources Information Center

Borgmeier, Chris; Horner, Robert H.

2006-01-01

Faced with limited resources, schools require tools that increase the accuracy and efficiency of functional behavioral assessment. Yarbrough and Carr (2000) provided evidence that informant confidence ratings of the likelihood of problem behavior in specific situations offered a promising tool for predicting the accuracy of function-based…
Evaluation of targeted and untargeted effects-based monitoring tools to assess impacts of contaminants of emerging concern on fish in the South Platte River, CO

EPA Science Inventory

Rivers in the arid Western United States face increasing influences from anthropogenic contaminants due to population growth, urbanization, and drought. To better understand and more effectively track the impacts of these contaminants, biologically-based monitoring tools are incr...
Using a Comprehensive Leadership Framework as a Scholarship and Teaching Tool

ERIC Educational Resources Information Center

Boyce, Kim

2006-01-01

Educators who work in community settings often encounter participants with a wide array of individual leadership beliefs, attitudes, and experiences. Given this situation, one of the challenges we face is to identify effective methods and tools to teach leadership in community and organizational settings. As an educator, it is important to…
Advanced Tools for Smartphone-Based Experiments: Phyphox

ERIC Educational Resources Information Center

Staacks, S.; Hütz, S.; Stampfer, C.; Heinke, H.

2018-01-01

The sensors in modern smartphones are a promising and cost-effective tool for experimentation in physics education, but many experiments face practical problems. Often the phone is inaccessible during the experiment and the data usually needs to be analyzed subsequently on a computer. We address both problems by introducing a new app, called…
"Dear Fresher …"--How Online Questionnaires Can Improve Learning and Teaching Statistics

ERIC Educational Resources Information Center

Bebermeier, Sarah; Nussbeck, Fridtjof W.; Ontrup, Greta

2015-01-01

Lecturers teaching statistics are faced with several challenges supporting students' learning in appropriate ways. A variety of methods and tools exist to facilitate students' learning on statistics courses. The online questionnaires presented in this report are a new, slightly different computer-based tool: the central aim was to support students…
Sanitation in wilderness: Balancing minimum tool policies and wilderness values

Treesearch

Paul R. Lachapelle

2000-01-01

Officials with the four wilderness managing agencies are faced with balancing wilderness preservation values and the minimum tool policies of their respective agencies. One example is the management of sanitation, particularly human waste and the often intrusive infrastructure that accompanies its treatment and disposal. Because the treatment and disposal of human...
Persistence and Change in Social Media

ERIC Educational Resources Information Center

Hogan, Bernie; Quan-Haase, Anabel

2010-01-01

In "Star Trek," Scotty suggests that Transwarp beaming is "like trying to hit a bullet with a smaller bullet, whilst wearing a blindfold, riding a horse." The study of social media faces similar challenges because new tools are developed at a rapid pace and existing tools are constantly being updated with new features, policies, and applications.…
29 CFR 1926.302 - Power-operated hand tools.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the source of supply or branch line to reduce pressure in case of hose failure. (8) Airless spray guns... the open barrel end. (6) Loaded tools shall not be left unattended. (7) Fasteners shall not be driven...-hardened steel, glass block, live rock, face brick, or hollow tile. (8) Driving into materials easily...
29 CFR 1926.302 - Power-operated hand tools.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the source of supply or branch line to reduce pressure in case of hose failure. (8) Airless spray guns... the open barrel end. (6) Loaded tools shall not be left unattended. (7) Fasteners shall not be driven...-hardened steel, glass block, live rock, face brick, or hollow tile. (8) Driving into materials easily...
29 CFR 1926.302 - Power-operated hand tools.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the source of supply or branch line to reduce pressure in case of hose failure. (8) Airless spray guns... the open barrel end. (6) Loaded tools shall not be left unattended. (7) Fasteners shall not be driven...-hardened steel, glass block, live rock, face brick, or hollow tile. (8) Driving into materials easily...
29 CFR 1926.302 - Power-operated hand tools.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the source of supply or branch line to reduce pressure in case of hose failure. (8) Airless spray guns... the open barrel end. (6) Loaded tools shall not be left unattended. (7) Fasteners shall not be driven...-hardened steel, glass block, live rock, face brick, or hollow tile. (8) Driving into materials easily...
29 CFR 1926.302 - Power-operated hand tools.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the source of supply or branch line to reduce pressure in case of hose failure. (8) Airless spray guns... the open barrel end. (6) Loaded tools shall not be left unattended. (7) Fasteners shall not be driven...-hardened steel, glass block, live rock, face brick, or hollow tile. (8) Driving into materials easily...
Integrating Six Sigma Concepts in an MBA Quality Management Class

ERIC Educational Resources Information Center

Weinstein, Larry B.; Petrick, Joseph; Castellano, Joseph; Vokurka, Robert J.

2008-01-01

Instructors face enormous challenges in presenting effective instruction on concepts and tools of quality management. Most textbooks focus on presenting individual concepts or tools and fail to address complex issues confronted in real-world problem-solving situations. The supplementary use of cases does not help students to understand the dynamic…
VideoANT: Extending Online Video Annotation beyond Content Delivery

ERIC Educational Resources Information Center

Hosack, Bradford

2010-01-01

This paper expands the boundaries of video annotation in education by outlining the need for extended interaction in online video use, identifying the challenges faced by existing video annotation tools, and introducing Video-ANT, a tool designed to create text-based annotations integrated within the time line of a video hosted online. Several…
Enhancing Knowledge Flow in a Health Care Context: A Mobile Computing Approach

PubMed Central

Souza, Diego Da Silva; de Lima, Patrícia Zudio; da Silveira, Pedro C; de Souza, Jano Moreira

2014-01-01

Background Advances in mobile computing and wireless communication have allowed people to interact and exchange knowledge almost anywhere. These technologies support Medicine 2.0, where the health knowledge flows among all involved people (eg, patients, caregivers, doctors, and patients’ relatives). Objective Our paper proposes a knowledge-sharing environment that takes advantage of mobile computing and contextual information to support knowledge sharing among participants within a health care community (ie, from patients to health professionals). This software environment enables knowledge exchange using peer-to-peer (P2P) mobile networks based on users’ profiles, and it facilitates face-to-face interactions among people with similar health interests, needs, or goals. Methods First, we reviewed and analyzed relevant scientific articles and software apps to determine the current state of knowledge flow within health care. Although no proposal was capable of addressing every aspect in the Medicine 2.0 paradigm, a list of requirements was compiled. Using this requirement list and our previous works, a knowledge-sharing environment was created integrating Mobile Exchange of Knowledge (MEK) and the Easy to Deploy Indoor Positioning System (EDIPS), and a twofold qualitative evaluation was performed. Second, we analyzed the efficiency and reliability of the knowledge that the integrated MEK-EDIPS tool provided to users according to their interest topics, and then performed a proof of concept with health professionals to determine the feasibility and usefulness of using this solution in a real-world scenario. Results . Using MEK, we reached 100% precision and 80% recall in the exchange of files within the peer-to-peer network. The mechanism that facilitated face-to-face interactions was evaluated by the difference between the location indicated by the EDIPS tool and the actual location of the people involved in the knowledge exchange. The average distance error was <6.28 m for an indoor environment. The usability and usefulness of this tool was assessed by questioning a sample of 18 health professionals: 94% (17/18) agreed the integrated MEK-EDIPS tool provides greater interaction among all the participants (eg, patients, caregivers, doctors, and patients’ relatives), most considered it extremely important in the health scenario, 72% (13/18) believed it could increase the knowledge flow in a health environment, and 67% (12/18) recommend it or would like to recommend its use. Conclusions The integrated MEK-EDIPS tool can provide more services than any other software tool analyzed in this paper. The proposed integrated MEK-EDIPS tool seems to be the best alternative for supporting health knowledge flow within the Medicine 2.0 paradigm. PMID:25427923

Some links on this page may take you to non-federal websites. Their policies may differ from this site.