Laboratory studies to characterize the efficacy of sand capping a coal tar-contaminated sediment.

PubMed

Hyun, Seunghun; Jafvert, Chad T; Lee, Linda S; Rao, P Suresh C

2006-06-01

Placement of a microbial active sand cap on a coal tar-contaminated river sediment has been suggested as a cost effective remediation strategy. This approach assumes that the flux of contaminants from the sediment is sufficiently balanced by oxygen and nutrient fluxes into the sand layer such that microbial activity will reduce contaminant concentrations within the new benthic zone and reduce the contaminant flux to the water column. The dynamics of such a system were evaluated using batch and column studies with microbial communities from tar-contaminated sediment under different aeration and nutrient inputs. In a 30-d batch degradation study on aqueous extracts of coal tar sediment, oxygen and nutrient concentrations were found to be key parameters controlling the degradation rates of polycyclic aromatic hydrocarbons (PAHs). For the five PAHs monitored (naphthalene, fluorene, phenanthrene, anthracene, and pyrene), degradation rates were inversely proportional to molecular size. For the column studies, where three columns were packed with a 20-cm sand layer on the top of a 5 cm of sediment layer, flow was established to sand layers with (1) aerated water, (2) N(2) sparged water, or (3) HgCl(2)-sterilized N(2) sparged water. After steady-state conditions, PAH concentrations in effluents were the lowest in the aerated column, except for pyrene, whose concentration was invariant with all effluents. These laboratory scale studies support that if sufficient aeration can be achieved in the field through either active and passive means, the resulting microbially active sand layer can improve the water quality of the benthic zone and reduce the flux of many, but not all, PAHs to the water column.

Processes controlling the seasonal and spatial variations in sulfate profiles in the pore water of the sediments surrounding Qi'ao Island, Pearl River Estuary, Southern China

NASA Astrophysics Data System (ADS)

Wu, Zijun; Zhou, Huaiyang; Ren, Dezhang; Gao, Hang; Li, Jiangtao

2015-04-01

Marine sediments are the main sink for seawater sulfate and bacterial sulfate reduction is a major component of the global sulfur cycle. Nevertheless, the factors controlling sulfate reduction in the coastal estuary sediments that undergo spatial and temporal variations are still not fully understood. In this study, we measured the concentrations of SO42-, Cl-, CH4, and DIC, and the δ13C of DIC in the pore water of five sampling stations surrounding the Qi'ao Island, Pearl River Estuary, Southern China during the dry season in November 2011 and during the wet season in May 2012. The results showed that the dilution-mixing of the Pearl River with low-concentration sulfate significantly affects the downcore profiles of the sulfate concentrations in the pore water of these estuary sediments. During the wet season, the dilution-mixing of the layers from the top of the sediments to a depth of 14-18 cm occurred at the different sampling stations. In this layer, the sulfate reduction is not appreciable based on the plot of the pore water Cl- and SO42-. Below the dilution-mixing layers, however, sulfate reduction that is driven by the anaerobic oxidation of methane (AOM) occurs. In our comparison, it appeared that the AOM played more important role in the consumption of the pore water sulfate in May 2012 than in November 2011. Meanwhile, we observed a relatively good correlation (r2=0.64) between the depth of the sulfate-methane interface (SMI) and the sulfate concentration in the pore water of the top sediments in dry season, indicating that the pore water sulfate concentration appears to be a primary controlling factor for the depth of the SMI in this estuary. These results highlight the need for an integrated analysis of the hydrologically driven the variations in the sulfate profiles to improve our understanding of the biogeochemical cycling of C, Fe and S and their budgets in estuarine environments.

3D Chirp Sonar Images on Fluid Migration Pathways and Their Implications on Seafloor Stability East of the Fangliao Submarine Canyon Offshore SW Taiwan

NASA Astrophysics Data System (ADS)

Lu, Y. W.; Liu, C. S.; Su, C. C.; Hsu, H. H.; Chen, Y. H.

2015-12-01

This study utilizes both chirp sonar images and coring results to investigate the unstable seafloor strata east of the Fangliao Submarine Canyon offshore southwestern Taiwan. We have constructed 3D chirp sonar images from a densely surveyed block to trace the attitude of an acoustic transparent layer and features caused by fluid activities. Based on the distribution of this transparent layer and fluid-related features, we suggest that this transparent layer forms a pathway for fluid migration which induces fluid-related characters such as acoustic blanking and fluid chimneys in the 3D chirp sonar images. Cored seafloor samples are used in this study to investigate the sediment compositions. The 210Pb activity profiles of the cores show oscillating and unsteady values at about 20~25 cm from core top. The bulk densities of the core samples in the same section (about 20~25 cm from core top) give values lower than those at deeper parts of the cores. These results indicate that the water content is much higher in the shallow sediments than in the deeper strata. From core sample analyses, we deduce that the local sediments are disturbed by liquefaction. From the analyses of 3D chirp sonar images and core data, we suggest that the seafloor east of the Fangliao Submarine Canyon is in an unstable condition, if disturbed by earthquakes, submarine landslides and gravity flows could be easily triggered and cause some geohazards, like breaking submarine cables during the 2006 Pingtung earthquake event.

Radiocarbon dating Arctic deep marine sediment to refine the usage of Mn pattern as a stratigraphic tool

NASA Astrophysics Data System (ADS)

Chiu, Pin-Yao Bernie; Löwemark, Ludvig

2016-04-01

The distinctive pattern of Mn content in Arctic deep marine sediment has been used as a proxy to indicate glacial-interglacial cyclicity (Löwemark et al., 2014). As has been observed in many sediment cores, Mn peaks correspond to warm interglacial periods. In order to improve the preciseness of Mn pattern as a proxy, we collected the foraminifera Neogloboquadrina pachyderma (sinistral) from brownish, Mn-rich layers, and performed radiocarbon dating on selected cores collected during the LOMROG07, LOMROG09 and LOMROG12 expeditions. Additional cores form the YMER and AO96 expeditions are also included. Based on our general understanding of the Mn system in the Arctic Ocean, we predicted a Mn pattern with a high peak in the uppermost core top, representing the Holocene. This Holocene peak in Mn is separated from the underlying warm period MIS 3 by a Mn-poor interval also characterized by a drop in Ca. This Mn and Ca poor interval reperesents MIS 2 and the LGM. Older warm periods, such as MIS 3, 5, 7 etc will display a similar pattern with distinct Mn peaks, separated by Mn minima representing cold iperiods For example, the MIS 5 sometimes shown a distinct pattern with three Mn peaks representing MIS 5a, 5c and 5e. However, there are still some limitations in the applicability of Mn stratigraphy, such as the remobilization of the Mn layer and the core-top loss during coring. We performed AMS carbon 14 dating on more than 10 cores, and the result revealed several cases of lost core tops, leading to depletion or complete loss of the Holocene interval. In several cores, our AMS dating revealed a hiatus in the MIS2 interval. The complete lack of MIS2 sediment likely is the result of extremely slow sedimentation rate due to severe sea ice conditions, while places with records of LGM may be the result of polynyas within the sea ice, or certain circulation pattern. Consequently, although Mn pattern can be used as a preliminary tool to identify glacial-interglacial cycles, the loss core tops and glacial hiatuses limits the usage and accuracy of the correlation of Mn stratigraphies. Therefore, additional radiocarbon dating can refine our understanding of the Mn patterns in Arctic marine sediment and help to make it a better proxy for both paleoenvironmental reconstructions and for the age models. Further study on the cause of hiatus often encountered in the LGM interval is necessary to ensure the usefulness of Mn stratigraphy.

Small-scale seismogenic soft sediment deformation (Hirlatzhöhle, Upper Austria)

NASA Astrophysics Data System (ADS)

Salomon, Martina Lan; Grasemann, Bernhard; Plan, Lukas; Gier, Susanne

2014-05-01

The Hirlatz Cave lies in the Dachstein Massif about 2 km SW of Hallstatt, in the Upper Austrian Salzkammergut. With a length of 101 km, this karst cave, located in the Dachstein nappe (Northern Calcareous Alps), is the second largest known cave system in Austria. Within the cave, in the so-called Lehmklamm, located 2.8 km southeast of the cave entrance, laminated (mm-scale) Quaternary clay-sized sediments with interbedded fine-grained sandy layers are preserved. In these layers, numerous soft sediment deformation structures are preserved in many layers. The unconsolidated sediments show rhythmic layering of brighter, carbonate and quartz rich, and darker, more clay mineral rich horizontal varve-like layers, that are assumed to be fluvio-lacustrine deposits. The present study focuses on a very detailed documentation of an approximately 6.8 x 3 m vertical outcrop that was cut by a small brook. Centimeter to millimeter sized water escape structures (intruded cusps and flame structures), folds (detachment folds, fault bend folds) and faults (normal faults, fault propagation folds, bookshelf faults) are described. Because of the geometric analogy to seismogenic structures which have been described at two orders of magnitude larger scales from areas close to the Dead Sea Fault, we suggest that the formation of the investigated soft-sediment structures was also triggered by seismic events. The structures were mainly formed by three different mechanism: (i) North directed gravitational gliding near the sediment surface; (ii) Liquefaction resulting in a density discontinuity and decreasing in shear strength within in the stratified layers; (iii) Extensional faulting that cut through the stratified layers. Observations of coarsening upwards into sandy layers on the top of the outcrop and current ripple indicate a north-directed flow under phreatic conditions, which is opposite to the present flow direction of the vadose water in the cave. The fact that deformation and erosion mostly occur in the uppermost meter of the outcrop wall suggests a higher seismic activity and at least periodically higher flow rates during sedimentation of the younger deposits. Since several extremely deformed layers occur between undeformed ones, we suggest that deformation of the layers occurred only in the uppermost highly water saturated sediments and that several seismic events lead to the formation of the observed structures. A possible source responsible for the seismic event is the Salzach-Ennstal-Mariazeller-Puchberger (SEMP) strike-slip fault, which accommodates the active extrusion of the Eastern Alps towards the Pannonian Basin.

Shallow structure and stratigraphy of the carbonate West Florida continental slope and their implications to sedimentation and geohazards

USGS Publications Warehouse

Doyle, Larry J.

1983-01-01

An 1800-joule sparker survey of the West Florida continental slope between about 26?N and 29?15?N showed a top bed of Pleistocene age forming an irregular drape over a surface that is probably Pliocene. The contact between the top two layers is unconformable in the south and, in some places, shows karst collapse and solution features. Karst topography grades into a more hummocky erosional surface to the north, which in turn smoothes out; the contact become conformable still further north. A period of folding, which is widespread over the outer portion of the study area and which may be related to large scale mass wasting, occurred at about the same time represented by the unconformity. Significant subsidence has occurred as late as Pleistocene. The surface layer thins to a minimum (0 in the south) at about 525-meters water depth and then thickens again dramatically to the west, downslope. This thinning is interpreted to be due to the Loop Current, which flows from north to south in the area and which acts to block deposition and scour the bottom. Despite the fact that the margin is dominated by carbonates, usually associated with low sedimentation rates, there is widespread evidence of mass wasting affecting ancient and surficial deposits on the outer part of the upper slope. Three potential groups of geohazards identified are: 1. Potential bottom failure in areas where a thin top layer overlies the karst surface. 2. Potential for sliding and slumping. 3. Scour due to currents which could also affect drilling and engineering activities.

Isotope analyses of the lake sediments in the Plitvice Lakes, Croatia

NASA Astrophysics Data System (ADS)

Horvatinčić, Nada; Sironić, Andreja; Barešić, Jadranka; Bronić, Ines Krajcar; Nikolov, Jovana; Todorović, Nataša; Hansman, Jan; Krmar, Miodrag

2014-10-01

The analyses of radioactive isotopes 14C, 137Cs and 210Pb, and stable isotope 13C were performed in the sediment cores, top 40 cm, taken in 2011 from karst lakes Prošće and Kozjak in the Plitvice Lakes National Park, central Croatia. Frozen sediment cores were cut into 1 cm thick layers and dried. 14C activity in both carbonate and organic fractions was measured using accelerator mass spectrometry technique with graphite synthesis. 137Cs, 210Pb, 214Pb and 214Bi were measured by low level gamma spectrometry method on ORTECHPGe detector with the efficiency of 32%. Distribution of 14C activity from both lakes showed increase of the 14C activity in the top 10-12 cm in both carbonate and organic fractions as a response to thermonuclear bomb-produced 14C in the atmosphere in the sixties of the 20th century. Anthropogenically produced 137Cs was also observed in sediment profiles. Sedimentation rates for both lake sediments were estimated based on the unsupported 210Pb activity. Different 14C activity of the carbonate fraction (63-80 pMC, percent of modern carbon) and organic fraction (82-93 pMC) is the result of geochemical and biological processes of the sediment precipitation in the lake waters. This is also confirmed by the δ 13 C values of both fractions. Carbon isotope composition, a 14 C and δ 13 C, was compared with the lake sediments from the same lakes collected in 1989 and 2003.

Evidence for gassy sediments on the inner shelf of SE Korea from geoacoustic properties

NASA Astrophysics Data System (ADS)

Gorgas, Thomas J.; Kim, Gil Y.; Park, Soo C.; Wilkens, Roy H.; Kim, Dae C.; Lee, Gwang H.; Seo, Young K.

2003-05-01

The inner shelf of SE Korea is characterized by an up to 40 m thick blanket of soft sediments often characterized by acoustic turbidity (AT). This AT is caused by a layer of sub-surface gas, which prohibits the identification of geological structures below that gas layer. Sound speeds were measured directly in these sediments using the Acoustic Lance (AL) in both mid- and late-September 1999. In situ sound speeds obtained in mid-September varied between 1400 and 1550 m/s, and thus did not confirm the presence of gas within the top 3.5 m of the seafloor. However, signal waveforms suggested that a gassy layer might have been just below the depth penetrated by the Lance. In late-September, on the other hand, two sites showed an abrupt decrease in signal amplitudes and in sound speed (less than 800 m/s) at depths as shallow as 2 m below seafloor, indicating the presence of free gas bubbles. Piston-cored sediments were retrieved at the same sites in February 1999. X-radiographs of some of the cores revealed numerous microcracks caused by the expansion of gas bubbles during core retrieval. In contrast to in situ acoustic data, ultrasonic sound speeds acquired in the laboratory in May 1999 on those cores did not differentiate convincingly between gas-bearing and gas-free sediments. Our measurements on the SE Korean shelf with the AL provide new data on the in situ acoustic behavior of gassy sediments and the sediments that overlie them in zones of AT.

Chemical gradients in sediment cores from an EPA reference site off the Farallon Islands - Assessing chemical indicators of dredged material disposal in the deep sea

USGS Publications Warehouse

Bothner, Michael H.; Gill, P.W.; Boothman, W.S.; Taylor, B.B.; Karl, Herman A.

1998-01-01

Heavy metal and organic contaminants have been determined in undisturbed sediment cores from the US Environmental Protection Agency reference site for dredged material on the continental slope off San Francisco. As expected, the concentrations are significantly lower than toxic effects guidelines, but concentrations of PCBs, PAHs, Hg, Pb, and Clostridium perfringens (a bacterium spore found in sewage) were nearly two or more times greater in the surface sediments than in intervals deeper in the cores. These observations indicate the usefulness of measuring concentration gradients in sediments at the San Francisco deep ocean disposal site (SF-DODS) where a thin (0.5 cm thick) layer of dredged material has been observed beyond the boundary. This thin layer has not been chemically characterized by the common practice of homogenizing over the top 10 cm. An estimated 300 million cubic yards of dredged material from San Francisco Bay are expected to be discharged at the SF-DODS site during the next 50 years. Detailed depth analysis of sediment cores would add significant new information about the fate and effects of dredged material in the deep sea.

Dependence of stratocumulus-topped boundary-layer entrainment on cloud-water sedimentation: Impact on global aerosol indirect effect in GISS ModelE3 single column model and global simulations

NASA Astrophysics Data System (ADS)

Ackerman, A. S.; Kelley, M.; Cheng, Y.; Fridlind, A. M.; Del Genio, A. D.; Bauer, S.

2017-12-01

Reduction in cloud-water sedimentation induced by increasing droplet concentrations has been shown in large-eddy simulations (LES) and direct numerical simulation (DNS) to enhance boundary-layer entrainment, thereby reducing cloud liquid water path and offsetting the Twomey effect when the overlying air is sufficiently dry, which is typical. Among recent upgrades to ModelE3, the latest version of the NASA Goddard Institute for Space Studies (GISS) general circulation model (GCM), are a two-moment stratiform cloud microphysics treatment with prognostic precipitation and a moist turbulence scheme that includes an option in its entrainment closure of a simple parameterization for the effect of cloud-water sedimentation. Single column model (SCM) simulations are compared to LES results for a stratocumulus case study and show that invoking the sedimentation-entrainment parameterization option indeed reduces the dependence of cloud liquid water path on increasing aerosol concentrations. Impacts of variations of the SCM configuration and the sedimentation-entrainment parameterization will be explored. Its impact on global aerosol indirect forcing in the framework of idealized atmospheric GCM simulations will also be assessed.

Investigation of River Seismic Signal Induced by Sediment Transport and Water Flow: Controlled Dam Breaking Experiments

NASA Astrophysics Data System (ADS)

Chen, H. Y.; Chen, S. C.; Chao, W. A.

2015-12-01

Natural river's bedload often hard to measure, which leads numerous uncertainties for us to predict the landscape evolution. However, the measurement of bedload flux has its certain importance to estimate the river hazard. Thus, we use seismometer to receive the seismic signal induced by bedload for partially fill the gap of field measurement capabilities. Our research conducted a controlled dam breaking experiments at Landao River, Huisun Forest since it has advantage to well constraining the spatial and temporal variation of bedload transport. We set continuous bedload trap at downstream riverbed of dam to trap the transport bedload after dam breaking so as to analyze its grain size distribution and transport behavior. In the meantime we cooperate with two portable velocity seismometers (Guralp CMG6TD) along the river to explore the relationship between bedload transport and seismic signal. Bedload trap was divided into three layers, bottom, middle, and top respectively. After the experiment, we analyzed the grain size and found out the median particle size from bottom to top is 88.664mm, 129.601mm, and 214.801mm individually. The median particle size of top layer is similar with the upstream riverbed before the experiment which median particle size is 230.683mm. This phenomena indicated that as the river flow become stronger after dam breaking, the sediment size will thereupon become larger, which meant the sediment from upstream will be carried down by the water flow and turned into bedload. Furthermore, we may tell apart the seismic signal induced by water flow and bedload by means of two different position seismometers. Eventually, we may estimate the probable error band of bedload quantity via accurately control of water depth, time-lapse photography, 3D LiDAR and other hydrology parameters.

Impact of beaver ponds on river discharge and sediment deposition along the Chevral River, Ardennes, Belgium

NASA Astrophysics Data System (ADS)

Nyssen, Jan; Frankl, Amaury; Pontzeele, Jolien; De Visscher, Maarten; Billi, Paolo

2013-04-01

With the recovery of the European beaver (Castor fiber) and their capacity to engineer fluvial landscapes, questions arise as to how they influence river discharge and sediment transport. The Chevral river (Ardennes, Belgium) contains two beaver dam sequences which appeared in 2004 and count now about 30 dams. Flow discharges and sediment fluxes were measured at the in- and outflow of each dam sequence. Volumes of sediment deposited behind the dams were measured. Between 2004 and 2011, peak flows were topped off, and the magnitude of extreme events decreased. 1710 m³ of sediment were deposited behind the beaver dams, with an average sediment thickness of 25 cm. The thickness of the sediment layer is related to the area of the beaver ponds. Along the stream, beaver pond sediment thickness displayed a sinusoidal deposition pattern, in which ponds with thick sediment layers were preceded by a series of ponds with thinner sediment layers. A downstream textural coarsening in the dam sequences was also observed, probably due to dam failures subsequent to surges. Differences in sediment flux between the in- and outflow at the beaver pond sequence were related to the river hydrograph, with deposition taking place during the rising limbs and slight erosion during the falling limbs. The seven-year-old sequences have filtered 190 tons of sediment out of the Chevral river, which is of the same order of magnitude as the 374 tons measured in pond deposits, with the difference between the values corresponding to beaver excavations (60 tons), inflow from small tributaries, and runoff from the valley flanks. Hydrogeomorphic effects of C. fiber and C. canadensis activity are similar in magnitude. The detailed analysis of changes to hydrology in beaver pond sequences confirms the potential of beavers to contribute to river and wetland restoration and catchment management.

Distribution of selenium, molybdenum and uranium in sediment cores from the Colorado River delta, Baja California, Mexico.

PubMed

Orozco-Durán, A; Daesslé, L W; Gutiérrez-Galindo, E A; Muñoz-Barbosa, A

2012-01-01

The distribution of selenium, molybdenum and uranium was studied in ~1.5 m sediment cores from the Colorado River delta, at the Colorado (CR) and Hardy (HR) riverbeds. Core HR2 showed highest Se, Mo and U concentrations at its bottom (2.3, 0.95 and 1.8 μg g(-1)) within a sandy-silt layer deposited prior to dam construction. In CR5 the highest concentrations of these elements (0.9, 1.4 and 1.7 μg g(-1) respectively) were located at the top of the core within a surface layer enriched in organic carbon. A few samples from HR2 had Se above the probable toxic effect level guidelines.

Sedimentary Characteristics of Marine Events from se Coast of India: Case Studies of 2004 Tsunami and 2013 Phailin Cyclone

NASA Astrophysics Data System (ADS)

Karthikeyan, A.

2015-12-01

The 2004 Indian Tsunami has deposited a varied layer of sand sheets along the coast which depends upon on the coastal topography. Recognition Tsunami deposits were clearly observed as the sand sheets were laid over the soil which is distinctly different due to differences in the weathering and presence of organic material of vegetation. To understand the preservation potential of 2004 tsunami deposits we were studied a transect profile with seven pits sediments along Thiruvengadu coast , Nagapattinam. The study reveals that presence of sand sheets preserved a mínimum of 10 cm thickness to máximum of 22 cm and the distance is 300 from HTL. From the present study six sedimentary layers were identfied which are (a) Top sediments deposited after IOT, (b). Tsunami sand sheets (c) Silty sand (d). Erosional base and top (e) Silty sand (d) Lagoonal sediments. The 2013 Phailin cyclon with wind speed of 220 kmph which was remnant cyclonic circulation from south china; it had major impact on geomorphology and sedimentology of odisha coast. At rushikulya river mouth, Ganjam district, cyclone had produced washover sand sheets as described in eyewitness along the river mouth of both north and south bar. The study reveals that the washover sand sheets provides the inundation of the water level, and characteristics of sediments where storm deposit has a highly variable grain-size distribution with a marked coarsening at its landward extent, is better sorted, coarser, and has a sharp, non-erosional lower contact associated with buried vegetation and soil. Also, the thickness of cyclone deposits are about 5 cm with the distance from coast 80 m, heavy mineral percentage ranges between 9 % to 75% for entire pit and sandsheets lateral extent are about 45 m. The presence of the laminations and alternate layers of heavy minerals are indicative of the complexity of sedimentation on the coast. The recent marine event Phailin cylcone deposits and 2004 tsunami deposits characteristic and its preservations potential are helpful to identify the paleo tsunami sediment characteristics the along east coast of India. The present study can be used as the background for distinguishing the tsunami and cyclone sediments. Keywords: 2004 Tsunami preservation, 2013 phailin cylcone, sedimentology, Topography.

On the geotechnical characterisation of the polluted submarine sediments from Taranto.

PubMed

Vitone, Claudia; Federico, Antonio; Puzrin, Alexander M; Ploetze, Michael; Carrassi, Elettra; Todaro, Francesco

2016-07-01

This paper reports the results of the first geomechanical laboratory experiments carried out on the polluted submarine clayey sediments of the Mar Piccolo in Taranto (South of Italy). The study had to face with extreme difficulties for the very soft consistency of the sediments and the contaminants. The mineralogy, composition and physical properties of the sediments were analysed, along with their compression and shearing behaviour. The investigation involved sediments up to about 20 m below the seafloor, along three vertical profiles in the most polluted area of the Mar Piccolo, facing the Italian Navy Arsenal. The experimental results were used to derive a preliminary geotechnical model of the site, necessary for the selection and design of the most sustainable in situ mitigation solutions. Moreover, the experimental data reveal that the clayey sediments of the most polluted top layer do not follow the classical geotechnical correlations for normally consolidated deposits. This seems to open interesting perspectives about the effects of pollutants on the geotechnical behaviour of the investigated sediments.

Global Paleobathymetry Reconstruction with Realistic Shelf-Slope and Sediment Wedge

NASA Astrophysics Data System (ADS)

Goswami, A.; Hinnov, L. A.; Gnanadesikan, A.; Olson, P.

2013-12-01

We present paleo-ocean bathymetry reconstructions in a 0.1°x0.1° resolution, using simple geophysical models (Plate Model Equation for oceanic lithosphere), published ages of the ocean floor (Müller et al. 2008), and modern world sediment thickness data (Divins 2003). The motivation is to create realistic paleobathymetry to understand the effect of ocean floor roughness on tides and heat transport in paleoclimate simulations. The values for the parameters in the Plate Model Equation are deduced from Crosby et al. (2006) and are used together with ocean floor age to model Depth to Basement. On top of the Depth to Basement, we added an isostatically adjusted multilayer sediment layer, as indicated from sediment thickness data of the modern oceans and marginal seas (Divins 2003). We also created another version of the sediment layer from the Müller et al. dataset. The Depth to Basement with the appropriate sediment layer together represent a realistic paleobathymetry. A Sediment Wedge was modeled to complement the reconstructed paleobathymetry by extending it to the coastlines. In this process we added a modeled Continental Shelf and Continental Slope to match the extent of the reconstructed paleobathymetry. The Sediment Wedge was prepared by studying the modern ocean where a complete history of seafloor spreading is preserved (north, south and central Atlantic Ocean, Southern Ocean between Australia-Antarctica, and the Pacific Ocean off the west coast of South America). The model takes into account the modern continental shelf-slope structure (as evident from ETOPO1/ETOPO5), tectonic margin type (active vs. passive margin) and age of the latest tectonic activity (USGS & CGMW). Once the complete ocean bathymetry is modeled, we combine it with PALEOMAP (Scotese, 2011) continental reconstructions to produce global paleoworld elevation-bathymetry maps. Modern time (00 Ma) was assumed as a test case. Using the above-described methodology we reconstructed modern ocean bathymetry, starting with age of the oceanic crust. We then reconstructed paleobathymetry for PETM (55 Ma) and Cenomanian-Turonian (90 Ma) times. For each case, the final products are: a) a global depth to basement measurement map based on plate model and EarthByte published age of the ocean crust for modern world; b) global oceanic crust bathymetry maps with a multilayer sediment layer (two versions with two types of sediment layers based on: i) observed total sediment thickness of the modern oceans and marginal seas, and ii) EarthByte-estimated global sediment data for 00 Ma); c) global oceanic bathymetry maps (two versions with two types of sediment layers) with reconstructed shelf and slope; and d) global elevation-bathymetry maps (two versions with two types of sediment layers) with continental elevations (PALEOMAP) and ocean bathymetry. Similar maps for other geological times can be produced using this method provided that ocean crustal age is known.

Is the Core Top Really Modern? A Story of Chemical Erosion, Bioturbation, and Lateral Sediment Redistribution from the Eastern Equatorial Pacific

NASA Astrophysics Data System (ADS)

Mekik, F.

2016-12-01

Paleoceanographic work is based on calibrating paleo-environmental proxies using well-preserved core top sediments which represent the last one thousand years or less. However, core top sediments may be in places as old as 9000 years due to various sedimentary and diagenetic processes, such as chemical erosion, bioturbation and lateral sediment redistribution. We hypothesize that in regions with high surface ocean productivity, high organic carbon to calcite ratios reaching the seabed promote calcite dissolution in sediments, even in regions above the lysocline. This process may lead to chemical erosion of core tops which in turn may result in core top aging. The eastern equatorial Pacific (EEP), a popular site for calibration of paleoceanographic proxies, is such a place. Better understanding the relationship between core top age and dissolution will help correct biases inherent in proxy calibration because dissolution of foraminifers alters shell chemistry, and wholesale dissolution of sediments leads to core top aging and loss. We present both new and literature-based core top data of radiocarbon ages from the EEP. We created regional maps of both core top radiocarbon age and calcite preservation measured with the Globorotalia menardii Fragmentation Index (MFI; over 100 core tops). Our maps show a clear pattern of deep sea sedimentary calcite dissolution mimicking the pattern of surface ocean productivity observed from satellites and sediment traps in the EEP. Core top radiocarbon ages generally parallel the dissolution patterns observed in the region. Where this relationship does not hold true, bioturbation and/or lateral sediment redistribution may play a role. Down core radiocarbon and 230Th-normalized sediment accumulation rate data from several cores in the EEP support this hypothesis. Better understanding the role of diagenesis promotes the development of more reliable paleo-environmental proxies.

Are lake sediments mere archives of degraded organic matter? - evidence of rapid biotic changes tracked in sediments of pre-alpine Lake Lunz, Austria

NASA Astrophysics Data System (ADS)

Hollaus, Lisa-Maria; Khan, Samiullah; Schelker, Jakob; Ejarque, Elisabet; Battin, Tom; Kainz, Martin

2016-04-01

Lake sediments are used as sentinels of changes in organic matter composition and dynamics within lakes and their catchments. In an effort to investigate how past and recent hydrological extreme events have affected organic matter composition in lake sediments, we investigated the biogeochemical composition of sediment cores and settling particles, using sediment traps in the pre-alpine, oligotrophic Lake Lunz, Austria. We assessed annual sedimentation rates using 137Cs and 210Pb, time integrated loads of settling particles, analyze stable carbon (δ13C) and nitrogen (δ15N) isotopes to track changes of carbon sources and trophic compositions, respectively, and use source-specific fatty acids as indicators of allochthonous, bacterial, and algal-derived organic matter. Preliminary results indicate that settling particles of Lake Lunz (33 m depth) contain high algae-derived organic matter, as assessed by long-chain polyunsaturated fatty acids (LC-PUFA), indicating low degradation of such labile organic matter within the water column of this lake. However, LC-PUFA decreased rapidly in sediment cores below the sediment-water interface. Concentrations of phosphorous remained stable throughout the sediment cores (40 cm), suggesting that past changes in climatic forcing did not alter the load of this limiting nutrient in lakes. Ongoing work reveals dramatic biotic changes within the top layers of the sediment cores as evidenced by high numbers of small-bodied cladocerans (e.g., Bosmina) and large-bodied zooplankton (e.g., Daphnia) are only detected at lower sediment layers. Current research on these lake sediments is aimed at investigating how organic matter sources changed during the past century as a result of recorded weather changes.

Detection of Fracture Patterns Within the Southern Portion of a Residential Complex (Tepozanes), Los Reyes-La Paz County (Edo. de Mexico)

NASA Astrophysics Data System (ADS)

Chavez, R. E.; Arango, C.; Tejero, A.; Cifuentes, G.; Hernandez, E.

2008-12-01

Most of the urban zone within the Valley of Mexico is built on top of the sediments of the ancient lakes of Chalco, Xochimilco, Mexico, Texcoco, Xaltocan and Zumpango. The sediments that cover this great valley are mainly composed by highly saturated clay-sandy materials; which offer a weak resistance to the constructions built on top. In addition, the increasing need of water supply for the population living in the valley (~22 million inhabitants) has weakened the main groundwater aquifers. This has lead to a differentiated subsidence and collapse of buildings, habitation units and roads. These effects put in a serious risk the inhabitants and the infrastructure of the city. As an example, we present a case of an area located in a densely populated zone, within a low-income residential complex denominated Tepozanes. This is located in the Los Reyes-La Paz County (Mexico State), towards the southeastern portion of the Valley of Mexico. The area is geologically limited by the Chimalhuacan Hill to the N, by the Santa Catarina volcanic range to the S. The previously mentioned effects are evident in the constructions of some buildings, where an exposed fracture is found in the NE-SW direction. This feature is affecting the structure of one of them in the residential complex, where the fracture runs underneath. A geophysical study was proposed to characterize the subsoil and to define the fracturing patterns in the zone. The electrical resistivity tomography (ETR) method employing the capacitive and galvanic modes was used to define the fracturing patters and the position at depth of the saturated layers, which might affect the Residential buildings. As a complement, GPR (Ground Penetrating Radar) profiles were carried out on the same profiles to correlate the information obtained from the ETR capacitive method which has a better resolution in the shallower zone. The computed results show that the buildings foundations were set on top of a high resistivity layer (~1000 Ohm-m), with variable thickness (5 m to 20 m). This layer depicts important discontinuities that can be associated to fractures. Low resistivity sediments lie on top of the resistive horizon. This feature corresponds to saturated sediments (clays and sands) that due to the water flow tend to form areas with low mechanical resistance and vey high compressibility, producing subsidence, following the fracture pattern in the resistive layer. The GPR study defined the presence of small fractures to depths ranging between 1 m and 3 m, which can be correlated with the information provided by the capacitive method. A subsidence map was produced for the studied zone. The fracture pattern is found in the SW-NE direction, affecting the residential complex at the surrounding. Three exploratory wells were drilled within the studied area. The stratigraphy obtained correlated well with the electrical models.

Polychaete Tubes, Turbulence, and Erosion of Fine-Grained Sediment

NASA Astrophysics Data System (ADS)

Kincke-Tootle, A.; Frank, D. P.; Briggs, K. B.; Calantoni, J.

2016-02-01

The role of polychaete tubes protruding through the benthic boundary layer in promoting or hindering erosion of fine-grained sediment was examined in laboratory experiments. Diver core samples of the top 10cm of sediment were collected west of Trinity Shoal off the Louisiana coast in 10-m depth. Diver cores were used in laboratory experiments conducted in a unidirectional flume. Tubes that were constructed by polychaetes, which comprised 70% of the species from the study area, were inserted into the core sediment surface. The sediment cores were then placed in the 2-m long test section of a small oscillatory flow tunnel and high-speed, stereo particle image velocimetry was used to determine the 2-dimensional, 3-component fluid velocity at high temporal (100 Hz) and spatial (< 1mm vector spacing) resolution. The tubes that protruded above the boundary layer allowed vortices to be initiated. Tubes are made up of shell fragments and fine-grained sediment, allowing for some rigidity and resistance to the flow. Rigidity determines the resistance causing small-scale eddies to form. The small-scale turbulence incited scour erosion, allowing fine-grained particles to be suspended into the water and in some cases coarser particles to be mobilized. Less-rigid tubes succumb to the shear stress, inhibit the formation of small-scale eddies, limit sediment erodibility, and increase the critical shear stress of the sediment. Discussion will focus on a modification to the critical Shields parameter to account for the effects of benthic biological activity.

Short-term environmental impact of clam dredging in coastal waters (south of Portugal): chemical disturbance and subsequent recovery of seabed.

PubMed

Falcão, M; Gaspar, M B; Caetano, M; Santos, M N; Vale, C

2003-12-01

The physical and chemical changes in sediment and near bottom water caused by clam dredging were examined during July and September 1999, at two locations Vilamoura (VL) and Armona (AR), south coast of Portugal. Sediment cores and near bottom water were collected simultaneously before dredging (control samples) and within short time intervals (min-h) after dredging. After dredging operations, microphytobenthos coming from the path were accumulated in the re-worked sediment (ridge). Chlorophyll a in superficial sediment increased from 1.2 microg x g(-1) before dredging to 1.7 microg x g(-1) after dredging and these higher values remained for a few hours. However, the expected increase of chlorophyll a in near bottom water due to re-suspension was not observed. After sediment disturbance an instantaneous sorption of phosphorus onto iron oxides occurred in the upper sediment layers (from 2 to 3 micromol x g(-1) before dredging to 4-5 micromol x g(-1) after dredging). A microcosm experiment showed that after sediment disturbance HPO(4)(2-) dissolved in pore water decreased from 40 to 10 microM being simultaneously sorbed onto iron oxides formed in the top layer of sediment. The ammonium, nitrates, organic nitrogen, phosphate and silicate dissolved in pore water decreased immediately after dredging activity and simultaneously an increase in near bottom water was sporadically observed. Generally, the re-establishment of seabed was reached within a short time (min-h), at both stations (VL and AR).

Microbial diversity and anaerobic hydrocarbon degradation potential in an oil-contaminated mangrove sediment

PubMed Central

2012-01-01

Background Mangrove forests are coastal wetlands that provide vital ecosystem services and serve as barriers against natural disasters like tsunamis, hurricanes and tropical storms. Mangroves harbour a large diversity of organisms, including microorganisms with important roles in nutrient cycling and availability. Due to tidal influence, mangroves are sites where crude oil from spills farther away can accumulate. The relationship between mangrove bacterial diversity and oil degradation in mangrove sediments remains poorly understood. Results Mangrove sediment was sampled from 0–5, 15–20 and 35–40 cm depth intervals from the Suruí River mangrove (Rio de Janeiro, Brazil), which has a history of oil contamination. DGGE fingerprinting for bamA, dsr and 16S rRNA encoding fragment genes, and qPCR analysis using dsr and 16S rRNA gene fragment revealed differences with sediment depth. Conclusions Analysis of bacterial 16S rRNA gene diversity revealed changes with depth. DGGE for bamA and dsr genes shows that the anaerobic hydrocarbon-degrading community profile also changed between 5 and 15 cm depth, and is similar in the two deeper sediments, indicating that below 15 cm the anaerobic hydrocarbon-degrading community appears to be well established and homogeneous in this mangrove sediment. qPCR analysis revealed differences with sediment depth, with general bacterial abundance in the top layer (0–5 cm) being greater than in both deeper sediment layers (15–20 and 35–40 cm), which were similar to each other. PMID:22935169

Microbial diversity and anaerobic hydrocarbon degradation potential in an oil-contaminated mangrove sediment.

PubMed

Andrade, Luiza L; Leite, Deborah C A; Ferreira, Edir M; Ferreira, Lívia Q; Paula, Geraldo R; Maguire, Michael J; Hubert, Casey R J; Peixoto, Raquel S; Domingues, Regina M C P; Rosado, Alexandre S

2012-08-30

Mangrove forests are coastal wetlands that provide vital ecosystem services and serve as barriers against natural disasters like tsunamis, hurricanes and tropical storms. Mangroves harbour a large diversity of organisms, including microorganisms with important roles in nutrient cycling and availability. Due to tidal influence, mangroves are sites where crude oil from spills farther away can accumulate. The relationship between mangrove bacterial diversity and oil degradation in mangrove sediments remains poorly understood. Mangrove sediment was sampled from 0-5, 15-20 and 35-40 cm depth intervals from the Suruí River mangrove (Rio de Janeiro, Brazil), which has a history of oil contamination. DGGE fingerprinting for bamA, dsr and 16S rRNA encoding fragment genes, and qPCR analysis using dsr and 16S rRNA gene fragment revealed differences with sediment depth. Analysis of bacterial 16S rRNA gene diversity revealed changes with depth. DGGE for bamA and dsr genes shows that the anaerobic hydrocarbon-degrading community profile also changed between 5 and 15 cm depth, and is similar in the two deeper sediments, indicating that below 15 cm the anaerobic hydrocarbon-degrading community appears to be well established and homogeneous in this mangrove sediment. qPCR analysis revealed differences with sediment depth, with general bacterial abundance in the top layer (0-5 cm) being greater than in both deeper sediment layers (15-20 and 35-40 cm), which were similar to each other.

Using XRF Geochemical Data to Differentiate Storm Event Deposits in a Backbarrier Lake in Coastal Louisiana

NASA Astrophysics Data System (ADS)

Dietz, M.; Liu, K. B.; Bianchette, T. A.; Yao, Q.; McCloskey, T.

2016-12-01

Hurricanes Gustav and Ike consecutively impacted coastal Louisiana in 2008 and generated significant storm surges. Three sediment cores taken from Bay Champagne, a coastal backbarrier lake near Port Fourchon, Louisiana, clearly show a deposition layer of clastic sediment up to 17 cm thick attributable to these two storms. X-ray fluorescence (XRF) analysis indicates that the two storm events can be distinguished from one another based on contrasting geochemical profiles. The bottom layer, presumably deposited by Hurricane Gustav, has high concentrations of S, Cl, Ca, and Sr, suggesting a strong marine influence. The top layer, presumably attributed to Hurricane Ike, has high concentrations of Ti, Mn, Fe and Zn, indicative of material of terrestrial origin. The elemental concentration profiles suggest that the storm deposits in each core were deposited through two distinct hydrological processes: a storm surge -driven marine intrusion during Hurricane Gustav, followed by intensive freshwater flooding during Hurricane Ike. Using these deposits as modern analogs, this technique could be applied to characterize older storm layers in the sedimentary record and potentially provide information about their respective depositional mechanisms.

Altitude of the top of the Sparta Sand and Memphis Sand in three areas of Arkansas

USGS Publications Warehouse

Pugh, Aaron L.; Westerfield, Paul W.; Gonthier, Gerard; Poynter, David T.

1998-01-01

The Sparta Sand and Memphis Sand form the second most productive aquifer in Arkansas. The Sparta Sand and Memphis Sand range in thick- ness from 0 to 900 feet, consisting of fine- to medium-grained sands interbedded with layers of silt, clay, shale, and minor amounts of lignite. Within the three areas of interest, the top surface of the Sparta Sand and Memphis Sand dips regionally east and southeast towards the axis of the Mississippi Embayment syncline and Desha Basin. Local variations in the top surface may be attributed to a combination of continued development of structural features, differential compaction, localized faulting, and erosion of the surface prior to subsequent inundation and deposition of younger sediments.

Determining metal origins and availability in fluvial deposits by analysis of geochemical baselines and solid-solution partitioning measurements and modelling.

PubMed

Vijver, Martina G; Spijker, Job; Vink, Jos P M; Posthuma, Leo

2008-12-01

Metals in floodplain soils and sediments (deposits) can originate from lithogenic and anthropogenic sources, and their availability for uptake in biota is hypothesized to depend on both origin and local sediment conditions. In criteria-based environmental risk assessments, these issues are often neglected, implying local risks to be often over-estimated. Current problem definitions in river basin management tend to require a refined, site-specific focus, resulting in a need to address both aspects. This paper focuses on the determination of local environmental availabilities of metals in fluvial deposits by addressing both the origins of the metals and their partitioning over the solid and solution phases. The environmental availability of metals is assumed to be a key force influencing exposure levels in field soils and sediments. Anthropogenic enrichments of Cu, Zn and Pb in top layers could be distinguished from lithogenic background concentrations and described using an aluminium-proxy. Cd in top layers was attributed to anthropogenic enrichment almost fully. Anthropogenic enrichments for Cu and Zn appeared further to be also represented by cold 2M HNO3 extraction of site samples. For Pb the extractions over-estimated the enrichments. Metal partitioning was measured, and measurements were compared to predictions generated by an empirical regression model and by a mechanistic-kinetic model. The partitioning models predicted metal partitioning in floodplain deposits within about one order of magnitude, though a large inter-sample variability was found for Pb.

Timing of Glacial Lake Missoula Outburst Floods and the southwestern Cordilleran Ice Sheet retreat.

NASA Astrophysics Data System (ADS)

Hendy, I. L.; Bervid, H. D.; Carlson, A. E.

2017-12-01

Glacial Lake Missoula formed when the Purcell Trench Lobe dammed the Clark Fork River in Montana and catastrophically collapsed repeatedly through the last glacial period as the southern Cordilleran Ice Sheet advanced and retreated. A well-dated 50-kyr jumbo piston core MD02-2496 (48.97˚ N, 127.04˚ W, water depth of 1243 m) collected from the continental slope 75 km off Vancouver Island contains evidence of these floods. The in-situ bulk elemental composition of the 35-m core was determined at 1 mm intervals using an ITRAX X-ray Fluorescence (XRF) Core Scanner (Cox Analytical Instruments) at the Sediment Geochemistry Lab of the College of Earth, Ocean, and Atmospheric Sciences at Oregon State University. With 40 mixed planktonic foraminifera and bulk organic carbon 14C ages, the core provides a high-resolution resolution record of glaciomarine sedimentation during deglaciation. A series of >81 layers of fine-grained sediments with ancient (K/Ar ages of 300 Ma and eNd of -8) shale-like (high Rb counts) composition can be found between 19.6 and 9.2 m below coretop. These layers are interspersed by coarser grained, young (K/Ar ages of 100 Ma and eNd of -3) sediments containing ice-rafted debris (IRD). The composition and age of the layers indicates the sediments originated in Glacial Lake Missoula and were transported by ocean currents 250 miles north along the west coast of North America. The flood layers begin at 19.5 ka with five thin (<5 cm thick) layers before thick flood layers (>5 cm thick) appear after 19.3 ka. At 17.1 ka, IRD concentrations increase from <1 grain g-1 to 20 grains g-1, and remain >50 grains g-1 from 16.5-16.35 ka, except in flood layers, as the Juan de Fuca Strait deglaciated. Another 16 flood layers occur from 16.3-15.65 ka; however, the base and top of these layers are diffuse rather than abrupt like earlier flood layers suggesting enhanced mixing between flood and melt waters. The final flood layers from 14.9-14.5 ka are thin (<2 cm thick) suggesting that the final floods were small events similar to the initial floods. This well-dated sequence displays how Glacial Lake Missoula flood sedimentation changed during the advance and retreat of the Cordilleran Ice Sheet.

Chironomus riparius exposure to fullerene-contaminated sediment results in oxidative stress and may impact life cycle parameters

PubMed Central

Waissi, G.C; Bold, S; Pakarinen, K; Akkanen, J; Leppänen, M.T; Petersen, E.J; Kukkonen, J.V.K

2016-01-01

A key component of understanding the potential environmental risks of fullerenes (C60) is their potential effects on benthic invertebrates. Using the sediment dwelling invertebrate Chironomus riparius we explored the effects of acute (12 h and 24 h) and chronic (10 d, 15 d, and 28 d) exposures of sediment associated fullerenes. The aims of this study were to assess the impact of exposure to C60 in the sediment top layer ((0.025, 0.18 and 0.48) C60 mg/cm2) on larval growth, oxidative stress and emergence rates and to quantify larval body burdens in similarly exposed organisms. Oxidative stress localization was observed in the tissues next to the microvilli and exoskeleton through a method for identifying oxidative stress reactions generated by reactive oxygen species. Rapid intake of fullerenes was shown in acute experiments, whereas body residues decreased after chronic exposure. Transmission electron microscopy analysis revealed oxidative damage and structural changes in cells located between the lipid droplets and next to the microvilli layer in fullerene exposed samples. Fullerene associated sediments also caused changes in the emergence rate of males and females, suggesting that the cellular interactions described above or other effects from the fullerenes may influence reproduction rates. PMID:27178647

Suspended Alexandrium spp. hypnozygote cysts in the Gulf of Maine

NASA Astrophysics Data System (ADS)

Kirn, Sarah L.; Townsend, David W.; Pettigrew, Neal R.

2005-09-01

The life cycle of dinoflagellates of the genus Alexandrium includes sexual reproduction followed by the formation of a dormant hypnozygote cyst, which serves as a resting stage. Negatively buoyant cysts purportedly fall to the benthos where they undergo a mandatory period of quiescence. Previous reports of cysts in the surficial sediments of the Gulf of Maine, where Alexandrium blooms are well documented, show a broad distribution of cysts, with highest concentrations generally in sediments below 100 m depth. We report here an exploration of cysts suspended in the water column, where they would be better positioned to inoculate springtime Alexandrium populations. During cruises in February, April, and June of 2000, water samples were collected at depths just off the bottom (within 5 m), at the top of the bottom nepheloid layer, and near the surface (1 m) and examined for cyst concentrations. Suspended cysts were found throughout the Gulf of Maine and westernmost Bay of Fundy. Planktonic cyst densities were generally greater in near-bottom and top of the bottom nepheloid layer samples than in near-surface water samples; densities were of the order of 10 2 cysts m -3 in surface waters, and 10 2-10 3 cysts m -3 at near-bottom depths. Temporally, they were most abundant in February and least abundant in April. Reports by earlier workers of cysts in the underlying sediments were on the order of 10 3 cysts cm -3. We present calculations that demonstrate the likelihood of cyst resuspension from bottom sediments forced by swell and tidal currents, and propose that such resuspended cysts are important in inoculating the seasonal bloom. We estimate that suspended cysts may contribute significantly to the annual vegetative cell population in the Gulf of Maine.

Spatial and Vertical Distribution of Dechlorane Plus in Mangrove Sediments of the Pearl River Estuary, South China.

PubMed

Sun, Yu-Xin; Zhang, Zai-Wang; Xu, Xiang-Rong; Hao, Qin-Wei; Hu, Yong-Xia; Zheng, Xiao-Bo; Luo, Xiao-Jun; Diao, Zeng-Hui; Mai, Bi-Xian

2016-10-01

Thirty surface sediments and three sediment cores were collected from mangrove wetlands in the Pearl River Estuary of South China to investigate the spatial and vertical distribution of Dechlorane Plus (DP). DP concentrations in the mangrove surface sediments ranged from 0.0130 to 1.504 ng/g dry weight (dw). DP concentrations in sediments from Shenzhen were significantly greater than those from Guangzhou and Zhuhai. Anti-Cl11-DP, the dechlorinated product of anti-DP, was also detected in the mangrove sediments with concentrations ranged from not detected to 0.0198 ng/g dw. Significant positive relationship between anti-Cl11-DP and anti-DP levels was observed in the mangrove sediments, suggesting that photo and/or microbial degradation of anti-DP might occur in the sediments. The f anti values in the mangrove sediments were close to those in the technical DP products, suggesting that stereoselective enrichment of anti-DP may not exist in the mangrove sediments. DP concentrations in the mangrove sediment cores generally showed an increasing trend from the bottom to top layers. This is the first study to report the occurrence of DP and its degradation product in the mangrove wetlands.

Near-Surface Geologic Units Exposed Along Ares Vallis and in Adjacent Areas: A Potential Source of Sediment at the Mars Pathfinder Landing Site

NASA Technical Reports Server (NTRS)

Treiman, Allan H.

1997-01-01

A sequence of layers, bright and dark, is exposed on the walls of canyons, impact craters and mesas throughout the Ares Vallis region, Chryse Planitia, and Xanthe Terra, Mars. Four layers can be seen: two pairs of alternating dark and bright albedo. The upper dark layer forms the top surface of many walls and mesas. The upper dark-bright pair was stripped as a unit from many streamlined mesas and from the walls of Ares Valles, leaving a bench at the top of the lower dark layer, approximately 250 m below the highland surface on streamlined islands and on the walls of Ares Vallis itself. Along Ares Vallis, the scarp between the highlands surface and this bench is commonly angular in plan view (not smoothly curving), suggesting that erosion of the upper dark-bright pair of layers controlled by planes of weakness, like fractures or joints. These near-surface layers in the Ares Vallis area have similar thicknesses, colors, and resistances to erosion to layers exposed near the tops of walls in Valles Marineris (Treiman et al.) and may represent the same pedogenic hardpan units. From this correlation, and from analogies with hardpans on Earth, the light-color layers may be cemented by calcite or gypsum. The dark layers are likely cemented by an iron-bearing mineral. Mars Pathfinder instruments should permit recognition and useful analyses of hardpan fragments, provided that clean uncoated surfaces are accessible. Even in hardpan-cemented materials, it should be possible to determine the broad types of lithologies in the Martian highlands. However, detailed geochemical modeling of highland rocks and soils may be compromised by the presence of hardpan cement minerals.

Importance of the colmation layer in the transport and removal of cyanobacteria, viruses, and dissolved organic carbon during natural lake-bank filtration

USGS Publications Warehouse

Harvey, Ronald W.; Metge, David W.; LeBlanc, Denis R.; Underwood, Jennifer C.; Aiken, George R.; Butler, Kenna D.; McCobb, Timothy D.; Jasperse, Jay

2015-01-01

This study focused on the importance of the colmation layer in the removal of cyanobacteria, viruses, and dissolved organic carbon (DOC) during natural bank filtration. Injection-and-recovery studies were performed at two shallow (0.5 m deep), sandy, near-shore sites at the southern end of Ashumet Pond, a waste-impacted, kettle pond on Cape Cod, MA, that is subject to periodic blooms of cyanobacteria and continuously recharges a sole-source drinking-water aquifer. The experiment involved assessing the transport behaviors of bromide (conservative tracer), Synechococcus sp. IU625 (cyanobacterium, 2.6 ± 0.2 µm), AS-1 (tailed cyanophage, 110 nm long), MS2 (coliphage, 26 nm diameter), and carboxylate-modified microspheres (1.7 µm diameter) introduced to the colmation layer using a bag-and-barrel (Lee-type) seepage meter. The injectate constituents were tracked as they were advected across the pond water–groundwater interface and through the underlying aquifer sediments under natural-gradient conditions past push-point samplers placed at ∼30-cm intervals along a 1.2-m-long, diagonally downward flow path. More than 99% of the microspheres, IU625, MS2, AS-1, and ∼44% of the pond DOC were removed in the colmation layer (upper 25 cm of poorly sorted bottom sediments) at two test locations characterized by dissimilar seepage rates (1.7 vs. 0.26 m d−1). Retention profiles in recovered core material indicated that >82% of the attached IU625 were in the top 3 cm of bottom sediments. The colmation layer was also responsible for rapid changes in the character of the DOC and was more effective (by three orders of magnitude) at removing microspheres than was the underlying 20-cm-thick segment of sediment.

Entrainment at a sediment concentration interface in turbulent channel flow

NASA Astrophysics Data System (ADS)

Salinas, Jorge; Shringarpure, Mrugesh; Cantero, Mariano; Balachandar, S.

2016-11-01

In this work we address the role of turbulence on entrainment at a sediment concentration interface. This process can be conceived as the entrainment of sediment-free fluid into the bottom sediment-laden flow, or alternatively, as the entrainment of sediment into the top sediment-free flow. We have performed direct numerical simulations for fixed Reynolds and Schmidt numbers while varying the values of Richardson number and particle settling velocity. The analysis performed shows that the ability of the flow to pick up a given sediment size decreases with the distance from the bottom, and thus only fine enough sediment particles are entrained across the sediment concentration interface. For these cases, the concentration profiles evolve to a final steady state in good agreement with the well-known Rouse profile. The approach towards the Rouse profile happens through a transient self-similar state. Detailed analysis of the three dimensional structure of the sediment concentration interface shows the mechanisms by which sediment particles are lifted up by tongues of sediment-laden fluid with positive correlation between vertical velocity and sediment concentration. Finally, the mixing ability of the flow is addressed by monitoring the center of mass of the sediment-laden layer. With the support of ExxonMobil, NSF, ANPCyT, CONICET.

The Character and Formation of Elongated Depressions on the Upper Bulgarian Slope

NASA Astrophysics Data System (ADS)

Xu, Cuiling; Greinert, Jens; Haeckel, Matthias; Bialas, Jörg; Dimitrov, Lyubomir; Zhao, Guangtao

2018-06-01

Seafloor elongated depressions are indicators of gas seepage or slope instability. Here we report a sequence of slopeparallel elongated depressions that link to headwalls of sediment slides on upper slope. The depressions of about 250 m in width and several kilometers in length are areas of focused gas discharge indicated by bubble-release into the water column and methane enriched pore waters. Sparker seismic profiles running perpendicular and parallel to the coast, show gas migration pathways and trapped gas underneath these depressions with bright spots and seismic blanking. The data indicate that upward gas migration is the initial reason for fracturing sedimentary layers. In the top sediment where two young stages of landslides can be detected, the slopeparallel sediment weakening lengthens and deepens the surficial fractures, creating the elongated depressions in the seafloor supported by sediment erosion due to slope-parallel water currents.

Coevolution of bed surface patchiness and channel morphology: 1. Mechanisms of forced patch formation

USGS Publications Warehouse

Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

2015-01-01

Riverbeds frequently display a spatial structure where the sediment mixture composing the channel bed has been sorted into discrete patches of similar grain size. Even though patches are a fundamental feature in gravel bed rivers, we have little understanding of how patches form, evolve, and interact. Here we present a two-dimensional morphodynamic model that is used to examine in greater detail the mechanisms responsible for the development of forced bed surface patches and the coevolution of bed morphology and bed surface patchiness. The model computes the depth-averaged channel hydrodynamics, mixed-grain-size sediment transport, and bed evolution by coupling the river morphodynamic model Flow and Sediment Transport with Morphological Evolution of Channels (FaSTMECH) with a transport relation for gravel mixtures and the mixed-grain-size Exner equation using the active layer assumption. To test the model, we use it to simulate a flume experiment in which the bed developed a sequence of alternate bars and temporally and spatially persistent forced patches with a general pattern of coarse bar tops and fine pools. Cross-stream sediment flux causes sediment to be exported off of bars and imported into pools at a rate that balances downstream gradients in the streamwise sediment transport rate, allowing quasi-steady bar-pool topography to persist. The relative importance of lateral gravitational forces on the cross-stream component of sediment transport is a primary control on the amplitude of the bars. Because boundary shear stress declines as flow shoals over the bars, the lateral sediment transport is increasingly size selective and leads to the development of coarse bar tops and fine pools.

A large-scale field trial of thin-layer capping of PCDD/F-contaminated sediments: Sediment-to-water fluxes up to 5 years post-amendment.

PubMed

Cornelissen, Gerard; Schaanning, Morten; Gunnarsson, Jonas S; Eek, Espen

2016-04-01

The longer-term effect (3-5 y) of thin-layer capping on in situ sediment-to-surface water fluxes was monitored in a large-scale field experiment in the polychlorinated dibenzodioxin and dibenzofuran (PCDD/F) contaminated Grenlandfjords, Norway (4 trial plots of 10,000 to 40,000 m(2) at 30 to 100 m water depth). Active caps (designed thickness 2.5 cm) were established in 2 fjords, consisting of dredged clean clay amended with powdered activated carbon (PAC) from anthracite. These active caps were compared to 2 nonactive caps in one of the fjords (designed thickness 5 cm) consisting of either clay only (i.e., without PAC) or crushed limestone. Sediment-to-water PCDD/F fluxes were measured in situ using diffusion chambers. An earlier study showed that during the first 2 years after thin-layer capping, flux reductions relative to noncapped reference fields were more extensive at the fields capped with nonactive caps (70%-90%) than at the ones with PAC-containing caps (50%-60%). However, the present work shows that between 3 and 5 years after thin-layer capping, this trend was reversed and cap effectiveness in reducing fluxes was increasing to 80% to 90% for the PAC caps, whereas cap effectiveness of the nonactive caps decreased to 20% to 60%. The increasing effectiveness over time of PAC-containing "active" caps is explained by a combination of slow sediment-to-PAC mass transfer of PCDD/Fs and bioturbation by benthic organisms. The decreasing effectiveness of "nonactive" limestone and clay caps is explained by deposition of contaminated particles on top of the caps. The present field data indicate that the capping efficiency of thin active caps (i.e., enriched with PAC) can improve over time as a result of slow diffusive PCDD/F transfer from sediment to PAC particles and better mixing of the PAC by bioturbation. © 2015 SETAC.

Is the core top modern? Observations from the eastern equatorial Pacific

NASA Astrophysics Data System (ADS)

Mekik, Figen; Anderson, Robert

2018-04-01

A compilation of ages from 67 core tops in the eastern equatorial Pacific (EEP) does not display an easily discernible regional pattern. The ages range from 790 to over 15,000 years. The youngest core tops with the highest sediment focusing factors are located in the Panama Basin. There are weak but statistically significant inverse relationships between core top age and age-model based mass accumulation rates, bioturbation depth, linear sedimentation rate and sediment focusing factors. However, we found no statistically significant relationship between core top age and calcite dissolution in sediments or 230Th-normalized mass accumulation rates. We found evidence suggesting that greater amount of sediment focusing helps to preserve the carbonate fraction of the sediment where focusing is taking place. When focusing factors are plotted against percent calcite dissolved, we observe a strong inverse relationship, and core tops younger than 4500 years tend to occur where focusing factors are high and percent calcite dissolved values are low. Using labile organic carbon fluxes to estimate bioturbation depth in the sediments results in the observation that where bioturbation depth is shallow (<4 cm), the core top age has a strong, inverse relationship with sediment accumulation rate. We used the Globorotalia menardii Fragmentation Index (MFI) as an indicator of percent calcite dissolved in deep sea sediments. There is a distinct pattern to core top calcite dissolution in the EEP which delineates bands of high surface ocean productivity as well as the clear increase in dissolution downward on the flanks of the East Pacific Rise.

In-situ falling-head test for hydraulic conductivity: Evaluation in layered sediments of an analysis derived for homogenous sediments

NASA Astrophysics Data System (ADS)

Burnette, Matthew C.; Genereux, David P.; Birgand, François

2016-08-01

The hydraulic conductivity (K) of streambeds is a critical variable controlling interaction of groundwater and surface water. The Hvorslev analysis for estimating K from falling-head test data has been widely used since the 1950s, but its performance in layered sandy sediments common in streams and lakes has not previously been examined. Our numerical simulations and laboratory experiments show that the Hvorslev analysis yields accurate K values in both homogenous sediment (for which the analysis was originally derived) and layered deposits with low-K sand over high-K sand. K from the Hvorslev analysis deviated significantly from true K only when two conditions were present together: (1) high-K sand was present over low-K sand, and (2) the bottom of the permeameter in which K was measured was at or very near the interface between high-K and low-K. When this combination of conditions exists, simulation and laboratory sand tank results show that in-situ Hvorslev K underestimates the true K of the sediment within a permeameter, because the falling-head test is affected by low-K sediment outside of (below the bottom of) the permeameter. In simulation results, the maximum underestimation (occurring when the bottom of the permeameter was at the interface of high K over low K) was by a factor of 0.91, 0.59, and 0.12 when the high-K to low-K ratio was 2, 10, and 100, respectively. In laboratory sand tank experiments, the underestimation was by a factor of about 0.83 when the high-K to low-K ratio was 2.3. Also, this underestimation of K by the Hvorslev analysis was about the same whether the underlying low-K layer was 2 cm or 174 cm thick (1% or 87% of the domain thickness). Numerical model simulations were useful in the interpretation of in-situ field K profiles at streambed sites with layering; specifically, scaling the model results to the maximum measured K at the top of the field K profiles helped constrain the likely ratio of high K to low K at field locations with layered heterogeneity. Vertical K values are important in field studies of groundwater-surface water interaction, and the Hvorslev analysis can be a useful tool, even in layered media, when applied carefully.

Reconstructing the Glacial Cycle of the Last 150 ka in the Southern Bay of Bengal

NASA Astrophysics Data System (ADS)

Holmes, B.; Dekens, P.; Weber, M. E.; Lantzsch, H.; Reilly, B. T.; Das, S. K.; Martos, Y. M.; Williams, T.

2017-12-01

The Himalayas and resulting monsoonal climate provide the source and mechanism for sediment deposition in the Bay of Bengal. Sediments from the distal Bengal Fan collected during IODP expedition 354, with the exception the westernmost Site U1454, show a several meter thick, hemipelagic top layer representing the Late Quaternary. This interval has abundant foraminifera throughout and therefore presents a unique opportunity to reconstruct oceanographic conditions, alongside records of terrestrial climate variability. We reconstructed oceanographic conditions at IODP site U1452 (8°N, 87°E, 3671 m water depth), in the southern Bay of Bengal. The age model was constructed by tuning the core's sediment lightness, L*, to the EDML ice core. The Toba Ash 1 (73.7 ka) is an additional constraint leading to an age model with a total of 35 tie points. We sampled the top 3.5 m of sediment at 2 cm resolution, and picked between 8 to 30 tests of the mixed surface layer planktonic foraminifera G. sacculifer from each sample. The tests were cracked open between two glass plates and the sample was homogenized before being split into separate aliquots for d18O and Mg/Ca analysis. Mg/Ca data range from 2.5 to 4.1 mmol/mol and show a SST change of 2-4°C between glacial and interglacial times. The δ18O data range from -2.63 to 0.17‰. The data shows the shift from the cooler glacial period into the warming interglacial period at 15 ka ending the LGM. The apparent late timing of the deglaciation in the record could be an artifact of lower resolution of the δ18O data (compared to the benthic stack). It is also possible the offset in the timing is due to the age model limitations and the assumption of linear sedimentation rates between tie points. We will further explore the age model implications by measuring d18O on benthic foraminifera where available in the sediment core. In collaboration with scientists from IODP Expedition 354, this data can be used to examine the link between tropical ocean conditions, monsoon strength, and glacial cycles.

Unlocking the relationship of biotic integrity of impaired waters to anthropogenic stresses.

PubMed

Novotny, Vladimir; Bartosová, Alena; O'Reilly, Neal; Ehlinger, Timothy

2005-01-01

The Clean Water Act expressed its goals in terms of restoring and preserving the physical, chemical and biological integrity of the Nation's waters. Integrity has been defined as the ability of the water body's ecological system to support and maintain a balanced integrated, adaptive community of organisms comparable to that of a natural biota of the region. Several indices of biotic integrity (IBIs) have been developed to measure quantitatively the biotic composition and, hence, the integrity. Integrity can be impaired by discharges of pollutants from point and nonpoint sources and by other pollution-related to watershed/landscape and channel stresses, including channel and riparian zone modifications and habitat impairment. Various models that link the stressors to the biotic assessment endpoints, i.e., the IBIs, have been presented and discussed. Simple models that link IBIs directly to single or multiple surrogate stressors such as percent imperviousness are inadequate because they may not represent a true cause-effect proximate relationship. Furthermore, some surrogate landscape parameters are irreversible and the relationships cannot be used for development of plans for restoration of the water body integrity. A concept of a layered hierarchical model that will link the watershed, landscape and stream morphology pollution stressors to the biotic assessment endpoints (IBIs) is described. The key groups of structural components of the model are: IBIs and their metrics in the top layer, chemical water and sediment risks and a habitat quality index in the layer below, in-stream concentrations in water and sediments and channel/habitat impairment parameters in the third layer, and watershed/landscaper pollution generating stressors, land use change rates, and hydrology in the lowest layer of stressors. A modified and expanded Maximum Species Richness concept is developed and used to reveal quantitatively the functional relationships between the top two layers of the structural components and parameters of the model.

Development of a Shallow Decollement Along the South-Central Chile Margin from 2D Seismic Reflection Data

NASA Astrophysics Data System (ADS)

Olsen, K.; Bangs, N. L.; Arnulf, A. F.; Trehu, A. M.; Contreras Reyes, E.

2017-12-01

In January and February, 2017, we acquired approximately 5,000 km of deep-penetrating 2D seismic reflection data along the Chile trench between 30° - 44°S as a part of the 2017 Crustal Examination from Valdivia to Illapel to Characterize Huge Earthquakes (CEVICHE) project, on the R/V Langseth. We used a 6,600 in3 airgun source to shoot every 50 m and recorded shots on a 15,100 m, 1212 channel streamer. This survey targeted the structure of this subduction zone across the slip regions of the 2015 Illapel (Mw 8.3), the 2010 Maule (Mw 8.8), and 1960 Valdivia (Mw 9.5) earthquakes. Two dip lines between 37.5°S and 39°S, within the overlapping slip areas of the Maule and Valdivia earthquakes, show a range in the style of initial thrust faulting at the deformation front. At 37.5°S, just south of the Arauco Peninsula, protothrusts at the deformation front are typical of many well-sedimented trench sections in subduction zones worldwide. Here we observe incipient landward-dipping thrusts consisting of 15 faults with typical horizontal spacing of 750 m that can be seen to extend down through the entire 2.5 km thick sediment sequence to the top of the subducting ocean crust. Some form conjugate fault pairs, but all have small offsets of 10-50 m. These thrusts appear to sole into a proto-decollement located just above the top of the ocean crust; however, farther landward beneath the lower slope, a thick, 2.5 km, sequence of layered sediment can be traced > 20 km into the subduction zone. The position of the primary decollement appears to be located near the top of the trench sediment sequence, well above the proto-decollement, allowing subduction of the entire trench sequence. A second line at 39°S across the deformation front shows no frontal thrusts or apparent deformation within the 1.5 km thick section of trench sediment. All of the incoming sediment appears to be subducting beneath a stable decollement that we can image near the top of the trench sediment sequence. The decollement along the northern line may be currently stepping down and transitioning from minimal accretion, typical of this segment of the Chile margin, to accretion of the entire trench section. Alternatively, the initial deformation at the toe may cease and allow slip to shift upward to the shallow decollement and continue to subduct the entire trench sediment section.

Repeated sedimentation and exposure of glacial Lake Missoula sediments: A lake-level history at Garden Gulch, Montana, USA

NASA Astrophysics Data System (ADS)

Smith, Larry N.

2017-01-01

Glaciolacustrine sediments record lake transgression, regression, and subaerial modification of the silty lake-bottom of glacial Lake Missoula in the Clark Fork River valley. The sequence preserved at Garden Gulch, MT documents lake-level fluctuations at >65% of its full-pool volume. Twelve sedimentary cycles fine upwards from (1) very fine-grained sandy silt to (2) silt with climbing ripples to (3) rhythmically laminated silt and some clay. The cycles are fine-grained turbidites capped locally by thin layers of angular gravel derived from local bedrock outcrops. The gravels appear to be the toes of mass wasting lobes carried onto the exposed lakebed surface during repeated lake-level lowerings. Periglacial wedges, small rotational faults, involutions, and clastic dikes deform the tops of eleven cycles. The wedges are 10-30 cm wide, penetrate 30-70 cm deep, are spaced <1 m apart, and contain vertically oriented gravel and massive to laminated sediment. Wedges split and taper in plan view. A few thin silt-filled dikes, which branch and taper downwards from wedges, are interpreted as filled frost cracks. One 10-20 cm-wide sand-filled dike protrudes upward from a sand bed; it is interpreted as a liquefaction feature consistent with a filling and draining lake. The deformed cycle tops preserve evidence of periglacial cold, subaerial exposure, seasonal frost heave, and the incipient formation of sorted polygons. The lowest five cycles are thicker and display more periglacial modification at their tops than the upper seven cycles. The Garden Gulch section may represent as few as seven and as many as twelve substantial fillings and partial to complete drainings of glacial Lake Missoula.

Benchscale Assessment of the Efficacy of a Reactive Core Mat to Isolate PAH-spiked Aquatic Sediments.

PubMed

Meric, Dogus; Barbuto, Sara; Sheahan, Thomas C; Shine, James P; Alshawabkeh, Akram N

2014-01-01

This paper describes the results of a benchscale testing program to assess the efficacy of a reactive core mat (RCM) for short term isolation and partial remediation of contaminated, subaqueous sediments. The 1.25 cm thick RCM (with a core reactive material such as organoclay with filtering layers on top and bottom) is placed on the sediment, and approximately 7.5 - 10 cm of overlying soil is placed on the RCM for stability and protection. A set of experiments were conducted to measure the sorption characteristics of the mat core (organoclay) and sediment used in the experiments, and to determine the fate of semi-volatile organic contaminants and non-reactive tracers through the sediment and reactive mat. The experimental study was conducted on naphthalene-spiked Neponset River (Milton, MA) sediment. The results show nonlinear sorption behavior for organoclay, with sorption capacity increasing with increasing naphthalene concentration. Neponset River sediment showed a notably high sorption capacity, likely due to the relatively high organic carbon fraction (14%). The fate and transport experiments demonstrated the short term efficiency of the reactive mat to capture the contamination that is associated with the post-capping period during which the highest consolidation-induced advective flux occurs, driving solid particles, pore fluid and soluble contaminants toward the reactive mat. The goal of the mat placement is to provide a physical filtering and chemically reactive layer to isolate contamination from the overlying water column. An important finding is that because of the high sorption capacity of the Neponset River sediment, the physical filtering capability of the mat is as critical as its chemical reactive capacity.

Anthropopression markers in lake bottom sediments

NASA Astrophysics Data System (ADS)

Nadolna, Anna; Nowicka, Barbara

2014-05-01

Lakes are vulnerable to various types of anthropogenic disturbances. Responses of lake ecosystems to environmental stressors are varied and depend not only on the type of a factor but also on the lake natural resistance to degradation. Within the EULAKES project an evaluation of anthropogenic stress extent in a flow-through, postglacial, ribbon lake (Lake Charzykowskie) was carried out. It was assumed, that this impact manifests unevenly, depending on a type and degree of the pressure on the shore zones, water quality of tributaries, lake basin shape and dynamics of a water movement. It was stated, that anthropogenic markers are substances accumulated in bottom sediments as a result of allochthonous substances inflow from the catchment and atmosphere. Along the selected transects 105 samples from the top layer of sediments (about 20 cm) was collected representing the contemporary accumulation (about 15 years). The content of selected chemical elements and compounds was examined, including nutrients (TN and TP), heavy metals (arsenic, cadmium, lead, chromium, nickel, copper, zinc, mercury, iron, and manganese) and pesticides (DDT, DDD, DDE, DMDT , γ-HCH). The research was conducted in the deepest points of each lake basin and along the research transects - while choosing the spots, the increased intensity of anthropogenic impact (ports, roads with heavy traffic, wastewater discharge zones, built-up areas) was taken into consideration. The river outlets to the lake, where there are ecotonal zones between limnic and fluvial environment, were also taken into account. Analysis of the markers distribution was carried out against the diversity of chemical characteristics of limnic sediments. Ribbon shape of the lake basin and the dominant wind direction provide an opportunity of easy water mixing to a considerable depth. Intensive waving processes cause removal of the matter from the littoral zone towards lake hollows (separated by the underwater tresholds), where the top layer of sediments consists of organic sediment ("sapropel" type). The littoral zone is dominated by sandy material from the shores denudation. In river mouths sandy deltas are formed. The most contaminated sediments are deposited in the central pool, which is a natural trap for the substances flowing with the river that is draining wastewaters from urban areas. At its mouth the sediment samples were significantly contaminated with chromium, zinc, cadmium, copper, nickel, lead and mercury. A high content of total phosphorus was also detected. A different role is played by a large river flowing through the lake. While flushing the sediments it reduces their pollution. The lowest content of markers was detected in headwater areas and in littoral zones exposed to waving.

Sediment texture and metal contamination in the Venice Lagoon (Italy): A snapshot before the installation of the MOSE system

NASA Astrophysics Data System (ADS)

Zonta, Roberto; Botter, Margherita; Cassin, Daniele; Bellucci, Luca Giorgio; Pini, Roberto; Dominik, Janusz

2018-05-01

Sediments of the Venice Lagoon down to 50 cm depth were investigated to assess sediment texture and metal contamination status, before the construction and activation of the MOSE system, which is intended to prevent the periodical flood events affecting the lagoon and the city of Venice. 380 cores were collected in shallow-water areas of the lagoon, and analysed along their vertical profile to determine grain-size distribution and concentrations of some major and trace elements (Al, As, Cr, Cu, Fe, Hg, Mn, Ni, Pb and Zn), total carbon and organic carbon. Radionuclide analyses (137Cs, 210Pb) were performed on 15 cores in an attempt to establish sediment chronology and determine radionuclide inventories in erosional and depositional areas. On the whole-lagoon scale, strong depletion of particles <31 μm in diameter (from medium silt to clay fractions) was observed in sediments down to 10 cm depth in comparison to deeper layers. This depletion characterised both erosional and depositional areas, and may be caused by increased water dynamics and resuspension of sediment due to anthropogenic activities. The apparent sediment accumulation rate determined with 210Pbxs in depositional areas was estimated at 0.2-0.4 cm y-1. In the majority of cores, 210Pbxs inventories were lower than expected from atmospheric fallout, suggesting its export along with fine particles. The different sediment characteristics in terms of grain-size distribution and organic carbon content observed in the upper layer with respect to the deeper ones reflect the modification of the sedimentary balance in recent years. The loss of fine particles, even from sediments in depositional areas of the northern part of the lagoon, may herald changes in local sediment texture leading to a further depletion of morphodiversity, which in turn may lead to the reduction or loss of important lagoon habitats. On the whole-lagoon scale, the prevalently lithogenic elements (Al, As, Cr, Fe, Mn, Ni) decreased towards the top of the cores, reflecting the depletion of fine particles in the upper sediment layer due to winnowing in non-confined lagoon areas. In contrast, partly anthropogenic elements (Cu, Hg, Pb, Zn) increased up to the subsurface sediment layers (5-10 and/or 10-20 cm) as an effect of increasing pollutant inputs until a certain time in the past. Enrichment Factors (EF) were calculated from 9 cores, comparing concentrations in the "pre-industrial" (>100 years ago) and recent (surface layer, 0-5 cm) sediments. The mostly lithogenic elements were not enriched (EF ˜ 1), whereas the partly anthropogenic elements showed slight (Cu and Pb, EF ˜ 1.2) to significant (Hg and Zn, EF ˜ 2) enrichment. The shallow waters on the landward side (particularly close to freshwater inputs), the area nearby the industrial district of Porto Marghera and a small zone adjacent to the city of Chioggia were identified as the main pollutant accumulation sites. Mercury was the only element potentially harmful for aquatic life. Its concentration in the biologically active surface sediment layer (0-5 cm) exceeded the NOAA Effects Range-Median (ERM) value in 27% of samples, corresponding to 20% of the shallow-water surface area. The collected data set represents a valuable reference for monitoring the impact of the construction and operation of the MOSE system on the sediment features of the Venice Lagoon.

Laboratory Experiments of Sand Ripples with Bimodal Size Distributions Under Asymmetric Oscillatory Flows

NASA Astrophysics Data System (ADS)

Calantoni, J.; Landry, B. J.

2010-12-01

The dynamics of sand ripples are vital to understanding numerous coastal processes such as sediment transport, wave attenuation, boundary layer development, and seafloor acoustic properties. Though significant laboratory research has been conducted to elucidate oscillatory flow morphodynamics under various constant and transient forcing conditions, the majority of the previous experiments were conducted only for beds with unimodal size distributions of sediment. Recent oscillatory flow experiments as well as past laboratory observations in uniform flows suggest that the presence of heterogeneous size sand compositions may significantly impact ripple morphology, resulting in a variety of observable effects (e.g., sediment sorting, bed armoring, and altered transport rates). Experimental work was conducted in a small oscillatory flow tunnel at the Sediment Dynamics Laboratory at the Naval Research Laboratory, Stennis Space Center. Three different monochromatic oscillatory forcings having velocity asymmetry were used to study sand ripple dynamics over five bimodal and two unimodal sediment beds. The seven different mixtures were composed using two unimodal sands of different colors (blue/white) and median grain diameters (d=0.31 mm / d=0.65 mm) combined into various mixtures by mass (i.e., 0/100; 10/90; 25/75; 50/50; 75/25; 90/10; and 100/0 which denotes mass percentage of blue/white sand, respectively, within each mixture). High-definition video of the sediment bed profile was acquired in conjunction with sediment trap measurements to resolve differences in ripple geometries, migration and evolution rates due to the different sediment mixtures and flow conditions. Observational findings clearly illustrate sediment stratification within ripple crests and the depth of the active mixing layer in addition to supporting sediment sorting in previous research on symmetric oscillatory flows in which the larger grains collect on top of ripple crests and smaller grains in the troughs. Preliminary quantitative results illuminate variations in equilibrium ripple geometry, ripple migration rates, and transition time scales between equilibrium states, all as functions of the sediment size mixture and flow forcing.

Time averaging and stratigraphic disorder of molluscan assemblages in the Holocene sediments in the NE Adriatic (Piran)

NASA Astrophysics Data System (ADS)

Tomasovych, Adam; Gallmetzer, Ivo; Haselmair, Alexandra; Kaufman, Darrell S.; Zuschin, Martin

2016-04-01

Stratigraphic changes in temporal resolution of fossil assemblages and the degree of their stratigraphic mixing in the Holocene deposits are of high importance in paleoecology, conservation paleobiology and paleoclimatology. However, few studies quantified downcore changes in time averaging and in stratigraphic disorder on the basis of dating of multiple shells occurring in individual stratigraphic layers. Here, we investigate downcore changes in frequency distribution of postmortem ages of the infaunal bivalve Gouldia minima in two, ~150 cm-thick piston cores (separated by more than 1 km) in the northern Adriatic Sea, close to the Slovenian city Piran at a depth of 24 m. We use radiocarbon-calibrated amino acid racemization to obtain postmortem ages of 564 shells, and quantify age-frequency distributions in 4-5 cm-thick stratigraphic intervals (with 20-30 specimens sampled per interval). Inter-quartile range for individual 4-5 cm-thick layers varies between 850 and 1,700 years, and range encompassing 95% of age data varies between 2,000 and 5,000 years in both cores. The uppermost sediments (20 cm) are age-homogenized and show that median age of shells is ~700-800 years. The interval between 20 and 90 cm shows a gradual increase in median age from ~2,000 to ~5,000 years, with maximum age ranging to ~8,000 years. However, the lowermost parts of both cores show a significant disorder, with median age of 3,100-3,300 years. This temporal disorder implies that many shells were displaced vertically by ~1 m. Absolute and proportional abundance of the bivalve Gouldia minima strongly increases towards the top of the both cores. We hypothesize that such increase in abundance, when coupled with depth-declining reworking, can explain stratigraphic disorder because numerically abundant young shells from the top of the core were more likely buried to larger sediment depths than less frequent shells at intermediate sediment depths.

A deterministic (non-stochastic) low frequency method for geoacoustic inversion.

PubMed

Tolstoy, A

2010-06-01

It is well known that multiple frequency sources are necessary for accurate geoacoustic inversion. This paper presents an inversion method which uses the low frequency (LF) spectrum only to estimate bottom properties even in the presence of expected errors in source location, phone depths, and ocean sound-speed profiles. Matched field processing (MFP) along a vertical array is used. The LF method first conducts an exhaustive search of the (five) parameter search space (sediment thickness, sound-speed at the top of the sediment layer, the sediment layer sound-speed gradient, the half-space sound-speed, and water depth) at 25 Hz and continues by retaining only the high MFP value parameter combinations. Next, frequency is slowly increased while again retaining only the high value combinations. At each stage of the process, only those parameter combinations which give high MFP values at all previous LF predictions are considered (an ever shrinking set). It is important to note that a complete search of each relevant parameter space seems to be necessary not only at multiple (sequential) frequencies but also at multiple ranges in order to eliminate sidelobes, i.e., false solutions. Even so, there are no mathematical guarantees that one final, unique "solution" will be found.

Vertical distribution of major, minor and trace elements in sediments from mud volcanoes of the Gulf of Cadiz: evidence of Cd, As and Ba fronts in upper layers

NASA Astrophysics Data System (ADS)

Carvalho, Lina; Monteiro, Rui; Figueira, Paula; Mieiro, Cláudia; Almeida, Joana; Pereira, Eduarda; Magalhães, Vítor; Pinheiro, Luís; Vale, Carlos

2018-01-01

Mud volcanoes are feature of the coastal margins where anaerobic oxidation of methane triggers geochemical signals. Elemental composition, percentage of fine particles and loss on ignition were determined in sediment layers of eleven gravity cores retrieved from four mud volcanoes (Sagres, Bonjardim, Soloviev and Porto) and three undefined structures located on the deep Portuguese margin of the Gulf of Cadiz. Calcium was positively correlated to Sr and inversely to Al as well as to most of the trace elements. Vertical profiles of Ba, Cd and As concentrations, and their ratios to Al, in Porto and Soloviev showed pronounced enhancements in the top 50-cm depth. Sub-surface enhancements were less pronounced in other mud volcanoes and were absent in sediments from the structures. These profiles were interpreted as diagenetic enrichments related to the anaerobic oxidation of methane originated from upward methane-rich fluxes. The observed barium fronts were most likely caused by the presence of barite which precipitated at the sulphate-methane transition zone. Cd and As enrichments have probably resulted from successive dissolution/precipitation of sulphides in response to vertical shifts of redox boundaries.

Piezoelectric Resonator with Two Layers

NASA Technical Reports Server (NTRS)

Stephanou, Philip J. (Inventor); Black, Justin P. (Inventor)

2013-01-01

A piezoelectric resonator device includes: a top electrode layer with a patterned structure, a top piezoelectric layer adjacent to the top layer, a middle metal layer adjacent to the top piezoelectric layer opposite the top layer, a bottom piezoelectric layer adjacent to the middle layer opposite the top piezoelectric layer, and a bottom electrode layer with a patterned structure and adjacent to the bottom piezoelectric layer opposite the middle layer. The top layer includes a first plurality of electrodes inter-digitated with a second plurality of electrodes. A first one of the electrodes in the top layer and a first one of the electrodes in the bottom layer are coupled to a first contact, and a second one of the electrodes in the top layer and a second one of the electrodes in the bottom layer are coupled to a second contact.

Characterising weak layers that accommodate submarine landslides on the Northwest African continental slope

NASA Astrophysics Data System (ADS)

Urlaub, M.; Krastel, S.; Geersen, J.; Schwenk, T.

2017-12-01

Numerous studies invoke weak layers to explain the occurrence of large submarine landslides (>100 km³), in particular those on very gentle slopes (<3°). Failure conditions are thought to be met only within this layer, which is embedded between stable sediments. Although key to understanding failure mechanisms, little is known about the nature and composition of such weak layers, mainly because they are (1) often destroyed with the landslide and (2) difficult to reach with ship-based gravity and piston coring. The Northwest African continental slope hosts numerous large submarine landslides that are translational, such that failure takes place along bedding-parallel surfaces at different stratigraphic depths. This suggests that failure occurs along weak layers, which are deposited repeatedly over time. Using high resolution seismic reflection data we trace several failure surfaces of the Cap Blanc Slide complex offshore Northwest Africa to ODP-Site 658. Core-seismic integration shows that the failure surfaces coincide with diatom oozes that are topped by clay. Along Northwest Africa diatom-rich sediments are typically deposited at the end of glacial periods. In the seismic data these oozes show up as distinct high amplitude reflectors due to their characteristic low densities. Similar high-amplitude reflectors embedded into low-reflective seismic units are commonly observed in shallow sediments (<100 m below seafloor) along the entire Northwest African continental slope. The failure surfaces of at least three large landslides coincide with such reflectors. As the most recent Pleistocene glacial periods likely influenced sediment deposition along the entire Northwest African margin in a similar manner we hypothesize that diatom oozes play a critical role for the generation of submarine landslides off Northwest Africa as well as globally within subtropical regions. An initiative to drill the Northwest African continental slope with IODP is ongoing, within which this hypothesis shall be tested.

Importance of the Colmation Layer in the Transport and Removal of Cyanobacteria, Viruses, and Dissolved Organic Carbon during Natural Lake-Bank Filtration.

PubMed

Harvey, Ronald W; Metge, David W; LeBlanc, Denis R; Underwood, Jen; Aiken, George R; Butler, Kenna; McCobb, Timothy D; Jasperse, Jay

2015-09-01

This study focused on the importance of the colmation layer in the removal of cyanobacteria, viruses, and dissolved organic carbon (DOC) during natural bank filtration. Injection-and-recovery studies were performed at two shallow (0.5 m deep), sandy, near-shore sites at the southern end of Ashumet Pond, a waste-impacted, kettle pond on Cape Cod, MA, that is subject to periodic blooms of cyanobacteria and continuously recharges a sole-source drinking-water aquifer. The experiment involved assessing the transport behaviors of bromide (conservative tracer), sp. IU625 (cyanobacterium, 2.6 ± 0.2 µm), AS-1 (tailed cyanophage, 110 nm long), MS2 (coliphage, 26 nm diameter), and carboxylate-modified microspheres (1.7 µm diameter) introduced to the colmation layer using a bag-and-barrel (Lee-type) seepage meter. The injectate constituents were tracked as they were advected across the pond water-groundwater interface and through the underlying aquifer sediments under natural-gradient conditions past push-point samplers placed at ∼30-cm intervals along a 1.2-m-long, diagonally downward flow path. More than 99% of the microspheres, IU625, MS2, AS-1, and ∼44% of the pond DOC were removed in the colmation layer (upper 25 cm of poorly sorted bottom sediments) at two test locations characterized by dissimilar seepage rates (1.7 vs. 0.26 m d). Retention profiles in recovered core material indicated that >82% of the attached IU625 were in the top 3 cm of bottom sediments. The colmation layer was also responsible for rapid changes in the character of the DOC and was more effective (by three orders of magnitude) at removing microspheres than was the underlying 20-cm-thick segment of sediment. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Karst is a repository for old sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbs, H.C.

1994-04-01

The Paleozoic plateau of southeastern Minnesota has been repeatedly glaciated, and has accumulated several sheets of loess. In the eastern part of this area, most of the older sediments have been eroded away and the late Wisconsinan Peoria loess directly overlies limestone. A lag of erratics from one or more older tills occurs sporadically on the bedrock surface. A more complete record is preserved in some sinkholes and solution cavities. Sinkholes (surface depressions) contain material that washed or collapsed into the hole, as well as material that was deposited directly (such as loess). Solution cavities contain only material sorted bymore » water. Sinkhole fills exposed in roadcuts and quarry walls commonly lack the surface expression and black-dirt funnel'' of active sinkholes. Several of these contain erratic-bearing sediment interpreted as slopewash and mudflow. One appears to contain actual till--unsorted, unbedded pebble-loam that is not mixed with other materials commonly found on the limestone surface, such as red clay or loess. It cannot be determined whether this material was deposited directly or collapsed in later. Solution cavities are typically packed with sediment right up to the top. The bulk of such deposits is typically clay and silt; however, erratic pebbles are present in some. The fine sediment is sorted and bedded, at least in places. In one large cavity fill, a layer of rip-up clay clasts occurs near the top. Study of the stratigraphy of karst sediments in southeastern Minnesota is still preliminary. Techniques which are used to correlate them include: physical characteristics, texture analysis (on material that has not been sorted), sand and pebble lithology, and magnetic polarity. Techniques that could be used include clay mineralogy, geochemical analysis, and thermoluminescence.« less

P-wave and surface wave survey for permafrost analysis in alpine regions

NASA Astrophysics Data System (ADS)

Godio, A.; Socco, L. V.; Garofalo, F.; Arato, A.; Théodule, A.

2012-04-01

In various high mountain environments the estimate of mechanical properties of slope and sediments are relevant for the link of the geo-mechanical properties with the climate change effects. Two different locations were selected to perform seismic and georadar surveying, the Tsanteleina glacier (Gran Paradiso) and the Blue Lake in Val d'Ayas in the massif of Monterosa. The analysis of the seismic and GPR lines allowed to characterize the silty soil (top layer) and underlying bedrock. We applied seismic survey in time lapse mode to check the presence of "active" layer and estimate the mechanical properties of the moraines material and their sensitivity to the permafrost changes. Mechanical properties of sediments and moraines in glacial areas are related to the grain-size, the compaction of the material subjected to the past glacial activity, the presence of frozen materials and the reactivity of the permafrost to the climate changes. The test site of Tsanteleina has been equipped with sensors to monitor the temperature of soil and air and with time domain reflectometry to estimate the soil moisture and the frozen and thawing cycle of the uppermost material. Seismic reflections from the top of the permafrost layer are difficult to identify as they are embedded in the source-generated noise. Therefore we estimate seismic velocities from the analysis of traveltime refraction tomography and the analysis of surface wave. This approach provides information on compressional and shear waves using a single acquisition layout and a hammer acts as source. This reduces the acquisition time in complex logistical condition especially in winter period. The seismic survey was performed using 48 vertical geophones with 2 m spacing. The survey has been repeated in two different periods: summer 2011 and winter 2011. Common offset reflection lines with a 200 MHz GPR system (in summer) permitted to investigate the sediments and obtain information on the subsoil layering. The processing of seismic data involved the tomographic interpretation of traveltime P-wave first arrivals by considering the continuous refraction of the ray-paths. Several surface-wave dispersion curves were extracted in f-k domain along the seismic line and then inverted through a laterally constrained inversion algorithm to obtain a pseudo-2D section of S-wave velocity. Georadar investigation (about 2 km of georadar lines in the first site) confirmed the presence both of fine and coarse sediments in the uppermost layer; the seismic data allowed the moraines to be characterized down to 20-25 meters of depth. At the elevation of 2700 m asl, we observed a general decrease of the P-wave traveltimes collected in November, when the near surface layer was in frozen condition, respect to the data acquired in June. The frozen layer is responsible of the inversion of P-wave velocity with depth; the higher velocity layer (frozen) cannot be detected in the tomographic interpretation of refraction tomographic of the P-wave arrivals. Compressional wave velocity ranges from 700 m/s on the uppermost part, to 2000-2500 m/s in the internal part of the sediments reaching values higher than 5000 m/s at depth about 20 m. The analysis of surface wave permitted to estimate a slight increase from summer to winter of the S-wave velocity, in the depth range between 0 to 5 m.

Post-depositional redistribution processes and their effects on middle rare earth element precipitation and the cerium anomaly in sediments in the South Korea Plateau, East Sea

NASA Astrophysics Data System (ADS)

Kang, Jeongwon; Jeong, Kap-Sik; Cho, Jin Hyung; Lee, Jun Ho; Jang, Seok; Kim, Seong Ryul

2014-03-01

We sampled two box-core sediments from the slope of the eastern South Korea Plateau (SKP) in the East Sea (Sea of Japan) at water depths of 1400 and 1700 m. Two chemical fractions of extractable (hydroxylamine/acetic acid) and residual rare earth elements (REEs) together with Al, Ca, Fe, Mg, Mn, P, S, As, Mo, and U were analyzed to assess the post-depositional redistribution of REEs. Extractable Fe and Mn are noticeably abundant in the oxic topmost sediment layer (<3 cm). However, some trace elements (e.g., S, As, Mo, U) are more abundant at depth, where redox conditions are different. Analysis of upper continental crust (UCC)-normalized (La/Gd)UCC, (La/Yb)UCC, and (Ce/Ce*)UCC revealed that the extractable REE is characterized by middle REE (MREE) enrichment and a positive cerium (Ce) anomaly, different from the case of the residual fraction which shows slight enrichment in light REEs (LREEs) with no Ce anomaly. The extractable MREEs seem to have been incorporated into high-Mg calcite during reductive dissolution of Fe oxyhydroxides. In the top sediment layer, the positive Ce anomaly is attributed to Ce oxide, which can be mobilized in deeper oxygen-poor environments and redistributed in the sediment column. In addition, differential concentrations of Ce and other LREEs in pore water appear to result in variable (Ce/Ce*)UCC ratios in the extractable fraction at depth.

Functional structure of laminated microbial sediments from a supratidal sandy beach of the German Wadden Sea (St. Peter-Ording)

NASA Astrophysics Data System (ADS)

Bühring, Solveig I.; Kamp, Anja; Wörmer, Lars; Ho, Stephanie; Hinrichs, Kai-Uwe

2014-01-01

Hidden for the untrained eye through a thin layer of sand, laminated microbial sediments occur in supratidal beaches along the North Sea coast. The inhabiting microbial communities organize themselves in response to vertical gradients of light, oxygen or sulfur compounds. We performed a fine-scale investigation on the vertical zonation of the microbial communities using a lipid biomarker approach, and assessed the biogeochemical processes using a combination of microsensor measurements and a 13C-labeling experiment. Lipid biomarker fingerprinting showed the overarching importance of cyanobacteria and diatoms in these systems, and heterocyst glycolipids revealed the presence of diazotrophic cyanobacteria even in 9 to 20 mm depth. High abundance of ornithine lipids (OL) throughout the system may derive from sulfate reducing bacteria, while a characteristic OL profile between 5 and 8 mm may indicate presence of purple non-sulfur bacteria. The fate of 13C-labeled bicarbonate was followed by experimentally investigating the uptake into microbial lipids, revealing an overarching importance of cyanobacteria for carbon fixation. However, in deeper layers, uptake into purple sulfur bacteria was evident, and a close microbial coupling could be shown by uptake of label into lipids of sulfate reducing bacteria in the deepest layer. Microsensor measurements in sediment cores collected at a later time point revealed the same general pattern as the biomarker analysis and the labeling experiments. Oxygen and pH-microsensor profiles showed active photosynthesis in the top layer. The sulfide that diffuses from deeper down and decreases just below the layer of active oxygenic photosynthesis indicates the presence of sulfur bacteria, like anoxygenic phototrophs that use sulfide instead of water for photosynthesis.

Effect of hydro mechanical coupling on natural fracture network formation in sedimentary basins

NASA Astrophysics Data System (ADS)

Ouraga, Zady; Guy, Nicolas; Pouya, Amade

2018-05-01

In sedimentary basin context, numerous phenomena, depending on the geological time span, can result in natural fracture network formation. In this paper, fracture network and dynamic fracture spacing triggered by significant sedimentation rate are studied considering mode I fracture propagation using a coupled hydro-mechanical numerical methods. The focus is put on synthetic geological structure under a constant sedimentation rate on its top. This model contains vertical fracture network initially closed and homogeneously distributed. The fractures are modelled with cohesive zone model undergoing damage and the flow is described by Poiseuille's law. The effect of the behaviour of the rock is studied and the analysis leads to a pattern of fracture network and fracture spacing in the geological layer.

Brominated flame retardants in mangrove sediments of the Pearl River Estuary, South China: spatial distribution, temporal trend and mass inventory.

PubMed

Zhang, Zai-Wang; Sun, Yu-Xin; Sun, Kai-Feng; Xu, Xiang-Rong; Yu, Shen; Zheng, Tian-Ling; Luo, Xiao-Jun; Tian, Yun; Hu, Yong-Xia; Diao, Zeng-Hui; Mai, Bi-Xian

2015-03-01

Sediments were collected from three mangrove wetlands in the Pearl River Estuary (PRE) of South China to investigate spatial and temporal distributions of polybrominated diphenyl ethers (PBDEs), decabromodiphenyl ethane (DBDPE) and 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE). Concentrations of ΣPBDEs, DBDPE and BTBPE in mangrove sediments of the PRE ranged from 1.25-206, 0.364-34.9, and not detected-0.794 ng g(-1) dry weight, respectively. The highest concentrations of ΣPBDEs, DBDPE and BTBPE were found at the mangrove wetland from Shenzhen, followed by Zhuhai and Guangzhou, showing the dependence on the proximity to urban areas. PBDEs were the predominant brominated flame retardants (BFRs) in mangrove sediments. The concentrations of ΣPBDEs, DBDPE and BTBPE in sediment cores showed an increasing trend from the bottom to top layers, reflecting the increasing usage of these BFRs. The inventories of ΣPBDEs, DBDPE and BTBPE in mangrove sediments were 1962, 245, and 4.10 ng cm(-2), respectively. This is the first study to report the occurrence of DBDPE and BTBPE in mangrove ecosystems. Copyright © 2014 Elsevier Ltd. All rights reserved.

Numerical simulation of mechanical compaction of deepwater shallow sediments

NASA Astrophysics Data System (ADS)

Sun, Jin; Wu, Shiguo; Deng, Jingen; Lin, Hai; Zhang, Hanyu; Wang, Jiliang; Gao, Jinwei

2018-02-01

To study the compaction law and overpressure evolution in deepwater shallow sediments, a large-strain compaction model that considers material nonlinearity and moving boundary is formulated. The model considers the dependence of permeability and material properties on void ratio. The modified Cam-Clay model is selected as the constitutive relations of the sediments, and the deactivation/reactivation method is used to capture the moving top surface during the deposition process. A one-dimensional model is used to study the compaction law of the shallow sediments. Results show that the settlement of the shallow sediments is large under their own weight during compaction. The void ratio decreases strictly with burial depth and decreases more quickly near the seafloor than in the deeper layers. The generation of abnormal pressure in the shallow flow sands is closely related to the compaction law of shallow sediments. The two main factors that affect the generation of overpressure in the sands are deposition rate and permeability of overlying clay sediments. Overpressure increases with an increase in deposition rate and a decrease in the permeability of the overlying clay sediment. Moreover, an upper limit for the overpressure exists. A two-dimensional model is used to study the differential compaction of the shallow sediments. The pore pressure will still increase due to the inflow of the pore fluid from the neighboring clay sediment even though the deposition process is interrupted.

Prehistoric (Chalcolithic) Eastern Mediterranean tsunami deposit identified offshore central Israel

NASA Astrophysics Data System (ADS)

Tyuleneva, Natalia; Braun, Yael; Suchkov, Igor; Goodman-Tchernov, Beverly

2017-04-01

The shallow shelf area ( 15-30 m water depth) offshore Israel, bears great potential for paleo-tsunami studies. It was shown in the course of previous research that in these offshore marine deposits, tsunami generated sedimentary layers can be well preserved and readily identified; unlike in onshore sedimentary sequences, which experience continuous exogenous natural and anthropogenic influence. A sediment core, 219 cm long, was obtained from 15.3 m water depth, in about 4 km north of Caesarea. Grain size at 1 cm interval as well as XRD and XRF analyses at coarser resolution were performed. Previously carried out research allowed correlation of two anomalous layers in this core with well described sediment sequences offshore Caesarea. These two events correspond best with the proposed events of 749 AD and 1500 BC. Identified unusual layers in this core bear certain set of proxies that are characteristic for tsunami generated deposits and easily distinguished from the local normal marine setting. The latter is characterized by three dominating mineralogical components, such as carbonaceous sand derived either from biogenic material, namely shell fragments or from eroded limestones and dolomites that outcrop the mountains to the east; siliciclastic quartz for the sand fraction and mineral smectite for the clays. The supply of the two latter terrigenous sedimentary components comes from the Nile River, which has been a stable and predominant source of sediments for the past 8 ka. The aim of this study is to characterize the earliest unusual sedimentary layer found down core between 191 and 211 cm. This layer was attributed to a tsunami-generated sedimentary sequence in the studied core. Absolute age determination based on 14C gave the time frame from 5.6 to 6 ka BP, making this event the oldest identified in the Eastern Mediterranean to date. This tsunami corresponds to the Chalcolithic ('Copper Age') cultural period of the region. Prehistoric age of these sediments makes it impossible to correlate these identified tsunami generated sediments with any known tsunami or earthquake, since the event pre dates any written catalogues of the mentioned hazardous events. The results of this study allow to make following conclusions: (1) the unusual sedimentary layer carries indicators, characteristic for tsunami generated sediments in the studied core, such as distinct deviation of granulometric coefficients (mean, median, standard deviation, skewness, kurtosis) and presence of whole, imbricated bivalve mollusks shells; (2) the upper part of tsunami generated layer is characterized by increased content of illite, a characteristic clay mineral for terrestrial sediments; (3) increased content of heavy minerals and such elements as iron, titanium and zirconium at the top of the layer coincide with increased content of coarse sand fraction (541-1821 micron) suggesting deposition in high energy sedimentological setting and influence of a strong backwash wave, carrying terrestrial material to offshore marine environment.

Direct sampling during multiple sediment density flows reveals dynamic sediment transport and depositional environment in Monterey submarine canyon

NASA Astrophysics Data System (ADS)

Maier, K. L.; Gales, J. A.; Paull, C. K.; Gwiazda, R.; Rosenberger, K. J.; McGann, M.; Lundsten, E. M.; Anderson, K.; Talling, P.; Xu, J.; Parsons, D. R.; Barry, J.; Simmons, S.; Clare, M. A.; Carvajal, C.; Wolfson-Schwehr, M.; Sumner, E.; Cartigny, M.

2017-12-01

Sediment density flows were directly sampled with a coupled sediment trap-ADCP-instrument mooring array to evaluate the character and frequency of turbidity current events through Monterey Canyon, offshore California. This novel experiment aimed to provide links between globally significant sediment density flow processes and their resulting deposits. Eight to ten Anderson sediment traps were repeatedly deployed at 10 to 300 meters above the seafloor on six moorings anchored at 290 to 1850 meters water depth in the Monterey Canyon axial channel during 6-month deployments (October 2015 - April 2017). Anderson sediment traps include a funnel and intervalometer (discs released at set time intervals) above a meter-long tube, which preserves fine-scale stratigraphy and chronology. Photographs, multi-sensor logs, CT scans, and grain size analyses reveal layers from multiple sediment density flow events that carried sediment ranging from fine sand to granules. More sediment accumulation from sediment density flows, and from between flows, occurred in the upper canyon ( 300 - 800 m water depth) compared to the lower canyon ( 1300 - 1850 m water depth). Sediment accumulated in the traps during sediment density flows is sandy and becomes finer down-canyon. In the lower canyon where sediment directly sampled from density flows are clearly distinguished within the trap tubes, sands have sharp basal contacts, normal grading, and muddy tops that exhibit late-stage pulses. In at least two of the sediment density flows, the simultaneous low velocity and high backscatter measured by the ADCPs suggest that the trap only captured the collapsing end of a sediment density flow event. In the upper canyon, accumulation between sediment density flow events is twice as fast compared to the lower canyon; it is characterized by sub-cm-scale layers in muddy sediment that appear to have accumulated with daily to sub-daily frequency, likely related to known internal tidal dynamics also measured in the experiment. The comprehensive scale of the Monterey Coordinated Canyon Experiment allows us to integrate sediment traps with ADCP instrument data and seafloor core samples, which provides important new data to constrain how, when, and what sediment is transported through submarine canyons and how this is archived in seafloor deposits.

Hydrogeologic implications of increased septic-tank-soil-absorption system density, Ogden Valley, Weber County, Utah

USGS Publications Warehouse

Lowe, Mike; Miner, Michael L.; ,

1990-01-01

Ground water in Ogden Valley occurs in perched, confined, and unconfined aquifers in the valley fill to depths of 600 feet and more. The confined aquifer, which underlies only the western portion of the valley, is overlain by cleyey silt lacustrine sediments probably deposited during the Bonneville Basin's Little Valley lake cycle sometime between 90,000 and 150,000 years ago. The top of this cleyey silt confining layer is generally 25 to 60 feet below the ground surface. Unconfined conditions occur above and beyond the outer margin of the confining layer. The sediments overlying the confining layer are primarily Lake Bonneville deposits. Water samples from springs, streams, and wells around Pineview Reservoir, and from the reservoir itself, were collected and analyzed. These samples indicate that water quality in Ogden Valley is presently good. Average nitrate concentrations in the shallow unconfined aquifer increase toward the center of Ogden Valley. This trend was not observed in the confined aquifer. There is no evidence, however, of significant water-quality deterioration, even in the vicinity of Huntsville, a town that has been densely developed using septic-tank-soil-absorption systems for much of the time since it was founded in 1860.

Synimpact-postimpact transition inside Chesapeake Bay crater

USGS Publications Warehouse

Poag, Claude (Wylie)

2002-01-01

The transition from synimpact to postimpact sedimentation inside Chesapeake Bay impact crater began with accumulation of fallout debris, the final synimpact deposit. Evi dence of a synimpact fallout layer at this site comes from the presence of unusual, millimeter- scale, pyrite microstructures at the top of the Exmore crater-fill breccia. The porous geometry of the pyrite microstructures indicates that they originally were part of a more extensive pyrite lattice that encompassed a layer of millimeter-scale glass microspherules—fallout melt particles produced by the bolide impact. Above this microspherule layer is the initial postimpact deposit, a laminated clay-silt-sand unit, 19 cm thick. This laminated unit is a dead zone, which contains abundant stratigraphically mixed and diagenetically altered or impact-altered microfossils (foraminifera, calcareous nannofossils, dinoflagellates, ostracodes), but no evidence of indigenous biota. By extrapolation of sediment- accumulation rates, I estimate that conditions unfavorable to microbiota persisted for as little as <1 k.y. to 10 k.y. after the bolide impact. Subsequently, an abrupt improvement of the late Eocene paleoenvironment allowed species-rich assemblages of foraminifera, ostracodes, dinoflagellates, radiolarians, and calcareous nannoplankton to quickly reoccupy the crater basin, as documented in the first sample of the Chickahominy Formation above the dead zone.

Synimpact-postimpact transition inside Chesapeake Bay crater

USGS Publications Warehouse

Poag, C.W.

2002-01-01

The transition from synimpact to postimpact sedimentation inside Chesapeake Bay impact crater began with accumulation of fallout debris, the final synimpact deposit. Evidence of a synimpact fallout layer at this site comes from the presence of unusual, millimeter-scale, pyrite microstructures at the top of the Exmore crater-fill breccia. The porous geometry of the pyrite microstructures indicates that they originally were part of a more extensive pyrite lattice that encompassed a layer of millimeter-scale glass microspherules-fallout melt particles produced by the bolide impact. Above this microspherule layer is the initial postimpact deposit, a laminated clay-silt-sand unit, 19 cm thick. This laminated unit is a dead zone, which contains abundant stratigraphically mixed and diagenetically altered or impact-altered microfossils (foraminifera, calcareous nannofossils, dinoflagellates, ostracodes), but no evidence of indigenous biota. By extrapolation of sediment-accumulation rates, I estimate that conditions unfavorable to microbiota persisted for as little as <1 k.y. to 10 k.y. after the bolide impact. Subsequently, an abrupt improvement of the late Eocene paleoenvironment allowed species-rich assemblages of foraminifera, ostracodes, dinoflagellates, radiolarians, and calcareous nannoplankton to quickly reoccupy the crater basin, as documented in the first sample of the Chickahominy Formation above the dead zone.

Fluvial landscapes evolution in the Gangkou River basin of southern Taiwan: Evidence from the sediment cores

NASA Astrophysics Data System (ADS)

Chen, Jia-Hong; Chyi, Shyh-Jeng; Yen, Jiun-Yee; Lin, Li-Hung; Yen, I.-Chin; Yu, Neng-Ti; Ho, Lih-Der; Jen, Chia-Hung

2017-04-01

The Gangkou River basin is the largest basin in the eastern Hengchun Peninsula of Taiwan. Its main river length is 31km and the basin area is 102sq. km. The width of the active channel is relatively narrow, but the valley from the middle to downstream is remarkably wide, indicating a feature of underfit stream. We drilled two sediment cores in the downstream area, including a 30m core (core-A) from a higher terrace, which is 14m above mean sea level, and a 20m core (core-B) from a lower terrace, which is 4m above mean sea level. Most of the sediments in the core-A are mud, which represents the flood plain facies, and 14C dates in the core-A range from 11ka to 7ka BP. Furthermore, the sediment layers reveal signals of marine events at the core depths of 5m to 11m by X-ray fluorescence. In the core-B, there is an erosional surface at the core depth of 5m. The age of the fluvial gravel layer above the erosional surface is about 0.4ka BP, and the mud layer top the surface is about 8.5ka BP. The preliminary results show that (1) as the tectonic uplift rate induced by the marine terraces around the basin is 1.0 to 2.5 mm/yr, and the accumulation rate of the mud layer in the basin is 6.7 to 8.7 mm/yr, the sediments infilling (more than 30-meters-thick) in the downstream area of the basin should be the results of the lower tectonic uplifting and the higher post-glacial sea level rise and; (2) the marine sediment layer with 14C dates of 7.5ka to 8.5ka BP is very likely the remain of the maximum flooding surface (MFS) in the early Holocene. These results indicate that the fluvial landscapes evolution of the basin was controlled by the sea-level; (3) the erosional surface in the core-B indicates the Gangkou River continuously erode the infilling sediments from 7ka to 0.4ka BP. Previous studies show that the sea-level around Taiwan gradually declined from its high stand since 6ka, we proposed that the continuous erosion was probably the results of tectonic uplifting and eustatic sea-level fall.

A smoothed particle hydrodynamics (SPH) study on polydisperse sediment from technical activities on seabed

NASA Astrophysics Data System (ADS)

Tran-Duc, Thien; Phan-Thien, Nhan; Khoo, Boo Cheong

2018-02-01

Technical activities to collect poly-metallic nodules on a seabed are likely to disturb the top-layer sediment and re-suspend it into the ambient ocean water. The transport of the re-suspended polydisperse-sized sediment is a process in which particles' size variation leads to a difference in their settling velocities; and thus the polydispersity in sizes of sediment has to be taken into account in the modeling process. The sediment transport within a window of 12 km is simulated and analyzed numerically in this study. The sediment characteristic and the ocean current data taken from the Peru Basin, Pacific Ocean, are used in the simulations. More than 50% of the re-suspended sediment are found to return to the bottom after 24 h. The sediment concentration in the ambient ocean water does not exceed 3.5 kg/m3 during the observed period. The deposition rate steadily increases and reaches 70% of the sediment re-suspension rate after 24 h. The sediment plume created by the activities comprises mainly very fine sediment particles (clays and silts), whereas coarser particles (sands) are found in abundance in the deposited sediment within 1 km from the source location. It is also found that the deposition process of the re-suspended sediment is changed remarkably as the current velocity increases from 0.05 m/s (medium current) to 0.1 m/s (strong current). The strong sediment deposition trend is also observed as the sediment source moves continuously over a region due to the sediment scattering effect.

In Situ Sedimentological Evidence for Climate Change in Early Mars Provided by the Curiosity Rover in Gale Crater

NASA Astrophysics Data System (ADS)

Heydari, Ezat; Fairen, Alberto G.

2016-10-01

The Striated formation is one of the rock units that was deposited in Gale crater, Mars, during the Late Noachian to Hesperian time (4.2 to 3.6 billion years ago). It crops out for 3 km along the Curiosity's traverse. The Striated formation strikes N65○E and has a depositional dip of 10○ - 20○ to SE. It consists of 500 m to 1000 m of highly rhythmic layers each 1 m to 4 m in thickness. Study of MAHLI and MastCam images provided by the Curiosity Rover indicates that layers form fining-upward cycles consisting of thick-bedded to massive conglomerate at the base that grades upward to thinly bedded conglomerate, then to pebbly sandstone, and topped by laminated, fine grained sandstone. Layers show slump folds, soft sediment deformation, and cross-beddings.The highly rhythmic occurrence and the fining-upward grain size characteristic indicate that each layer within the Striated formation is a coarse-grained turbidite: a type of rock that forms when sediments move down-hill by gravity-driven turbidity flows and deposit in deep waters. We propose that turbidite layers of the Striated formation are related to delivery of sediments to Gale crater by megafloods through its northern rim. Upon entering Gale crater, sediments moved down-hill and deposited as turbidite layers when the crater may have been filled to the rim with water. About 1000 to 3000 turbidite layers are present suggesting the occurrences of as many megafloods during hothouse climatic intervals when Mars was warmer than the Present and had plenty of liquid water. Floods were generated by one or a combination of the following processes: (1) torrential rain along the margins of Mars's Northern Ocean, 500 km to 1000 km to the north, (2) rapid melting of ice in highland areas, and (3) tsunamis formed by impacts on the Northern Ocean. Cold and/or dry climate of icehouse intervals may have followed each warming episode. Mars's climate forcing mechanism and periodicities of climate change are not clear at this point. However, the highly regular and rhythmic nature of turbidite layers point to an orbital triggering mechanism, possibly driven by changes in obliquity.

Composition of the low seismic velocity E' layer at the top of Earth's core

NASA Astrophysics Data System (ADS)

Badro, J.; Brodholt, J. P.

2017-12-01

Evidence for a layer (E') at the top of the outer core has been available since the '90s and while different studies suggest slightly different velocity contrasts and thicknesses, the common observation is that the layer has lower velocities than the bulk outer core (PREM). Although there are no direct measurements on the density of this layer, dynamic stability requires it to be less dense than the bulk outer core under those same pressure and temperature conditions. Using ab initio simulations on Fe-Ni-S-C-O-Si liquids we constrain the origin and composition of the low-velocity layer E' at the top of Earth's outer core. We find that increasing the concentration of any light-element always increases velocity and so a low-velocity and low-density layer (for stability) cannot be made by simply increasing light element concentration. This rules out barodiffusion or upwards sedimentation of a light phase for its origin. However, exchanging elements can—depending on the elements exchanged—produce such a layer. We evaluate three possibilities. Firstly, crystallization of a light phase from a core containing more than one light element may make such a layer, but only if the crystalizing phase is very Fe-rich, which is at odds with available phase diagrams at CMB conditions. Secondly, the E' layer may result from incomplete mixing of an early Earth core with a late impactor, depending on the light element compositions of the impactor and Earth's core, but such a primordial stratification is neither supported by dynamical models of the core nor thermodynamic models of core merger after the giant impact. The last and most plausible scenario is core-mantle chemical interaction; using thermodynamic models for metal-silicate partitioning of silicon and oxygen at CMB conditions, we show that a reaction between the core and an FeO-rich basal magma ocean can enrich the core in oxygen while depleting it in silicon, in relative amounts that produce a light and slow layer consistent with seismological observations.

Role of mariculture in the loading and speciation of mercury at the coast of the East China Sea.

PubMed

Liang, Peng; Gao, Xuefei; You, Qiongzhi; Zhang, Jin; Cao, Yucheng; Zhang, Chan; Wong, Ming-Hung; Wu, Sheng-Chun

2016-11-01

The effects of mariculture on mercury (Hg) contamination and speciation in water, sediment and cultured fish in a typical mariculture zone located in Xiangshan bay, Zhejiang province, east China, were studied. Water, sediment and fish samples were collected from mariculture sites (MS) and from corresponding reference sites (RS) 2500 m away from the MS. The THg concentration in overlying water in Xiangshan bay reached as high as 16.6 ± 19.5 ng L -1 , indicating that anthropogenic sources in this bay may contribution on Hg contamination in overlying water. Mariculture activities resulted in an increase in THg concentration in water from surface and bottom layers, which may be attributed to the discharge of domestic sewage and the accumulation of unconsumed fish feed and fish excreta in the benthic environment. Methylmercury (MeHg) concentrations in the bottom layer of overlying water and top surface layer of porewater underneath MS were higher than at RS, implying that mariculture activities promote Hg methylation in the interface between sediments and water. In addition, the concentrations of MeHg in sediment and porewater were significantly higher in summer than winter. It was observed that THg and MeHg contents in the muscle of blackhead seabream (Acanthopagrus schlegelii) (fed by the trash fish) were significantly higher (p < 0.001) than those in red snapper (Lutjanus campechanus) or perch (Perca fluviatilis) (fed by pellet fish feed). The THg and MeHg concentrations in the fish meat were closely related to the feeding mode, which indicate that fish feed rather than environmental media is the major pathway for Hg accumulation in fish muscle. Copyright © 2016 Elsevier Ltd. All rights reserved.

Constraining the velocity structure of the Juan de Fuca plate from ridge to trench with a 2D tomographic study of wide angle OBS data

NASA Astrophysics Data System (ADS)

Boulahanis, B.; Canales, J. P.; Carbotte, S. M.; Carton, H. D.; Han, S.; Nedimovic, M. R.

2016-12-01

We conduct a two-dimensional travel time tomography study of a cross-plate, 300-km long, ocean bottom seismometer (OBS) transect collected as part of the Ridge to Trench (R2T) program to investigate the structure, evolution and state of hydration of the Juan de Fuca (JdF) plate from the ridge axis to subduction at the Cascadia margin offshore Washington. Our study employs the methodology of Korenaga et al. (2000) to derive a P-wave velocity model using wide-angle data from 15 OBSs spaced on average 15 km apart, spanning from the Endeavour segment of the JdF ridge to the Cascadia accretionary prism. A top down modeling approach is employed, first assessing velocities of the sediment layer, then the crust, and finally the upper mantle; at each stage of the inversion we fix the structure of the overlaying layers. Quality of data fit is evaluated using the root mean square value of the difference between predicted and observed travel times normalized by pick uncertainty. Previous studies provide a well-resolved multi-channel seismic (MCS) reflection image of this transect (Han et al., 2016), affording good constraints of the location of basement and Moho reflectors while allowing for comparison of the relationship between velocities and crustal structure. MCS results along this transect suggest evidence of little bending faulting confined to the sediment and upper-middle crust. An initial velocity model of the sediment layer above igneous crust is constructed utilizing the MCS derived sediment velocities. A one-dimensional velocity starting model of the oceanic crust is generated using the results of Horning et al. (in press) from a quasi-parallel cross-plate transect also acquired as part of the R2T study. Seismic velocities are compared to predicted velocities for crustal and mantle lithologies at temperatures estimated from a plate-cooling model and are used to provide constraints on water contents in these layers.

Vertical structure of aeolian turbulence in a boundary layer with sand transport

NASA Astrophysics Data System (ADS)

Lee, Zoe S.; Baas, Andreas C. W.

2016-04-01

Recently we have found that Reynolds shear stress shows a significant variability with measurement height (Lee and Baas, 2016), and so an alternative parameter for boundary layer turbulence may help to explain the relationship between wind forcing and sediment transport. We present data that were collected during a field study of boundary layer turbulence conducted on a North Atlantic beach. High-frequency (50 Hz) 3D wind velocity measurements were collected using ultrasonic anemometry at thirteen different measurement heights in a tight vertical array between 0.11 and 1.62 metres above the surface. Thanks to the high density installation of sensors a detailed analysis of the boundary layer flow can be conducted using methods more typically used in studies where data is only available from one or just a few measurement heights. We use quadrant analysis to explore the vertical structure of turbulence and track the changes in quadrant signatures with measurement elevation and over time. Results of quadrant analysis, at the 'raw' 50 Hz timescale, demonstrates the tendency for event clustering across all four quadrants, which implies that at-a-point quadrant events are part of larger-scale turbulent structures. Using an HSV colour model, applied to the quadrant analysis data and plotted in series, we create colour maps of turbulence, which can provide a clear visualisation of the clustering of event activity at each height and illustrate the shape of the larger coherent flow structures that are present within the boundary layer. By including a saturation component to the colour model, the most significant stress producing sections of the data are emphasised. This results in a 'banded' colour map, which relates to clustering of quadrant I (Outward Interaction) and quadrant IV (Sweep) activity, separate from clustering of quadrant II (Burst) and quadrant III (Inward Interaction). Both 'sweep-type' and 'burst-type' sequences are shown to have a diagonal structure originating from the top of the boundary layer, indicating a downwards direction of eddy motion. While directionality of turbulence cannot be definitively determined, our results indicate that the top-down turbulence model is a suitable explanation, further supported by the presence of 'incomplete' eddies which originate at higher elevations but fail to extend to the surface. This provides the first evidence in support of a top down turbulence model as observed in aeolian geomorphology, and we present preliminary findings on its relationship to sand transport activity. Lee, Z.S., Baas, A.C.W. (2016) Variable and conflicting shear stress estimates inside a boundary layer with sediment transport. Earth Surface Processes and Landforms; DOI: 10.1002/esp.3829

A Classification of Subaqueous Density Flows Based on Transformations From Proximal to Distal Regions

NASA Astrophysics Data System (ADS)

Hermidas, Navid; Eggenhuisen, Joris; Luthi, Stefan; Silva Jacinto, Ricardo; Toth, Ferenc; Pohl, Florian

2017-04-01

Transformations of a subaqueous density flow from proximal to distal regions are investigated. A classification of these transformations based on the state of the free shear and boundary layers and existence of a plug layer during transition from a debris flow to a turbidity current is presented. A connection between the emplaced deposit by the flow and the relevant flow type is drawn through the results obtained from a series of laboratory flume experiments. These were performed using 9%, 15%, and 21% sediment mixture concentrations composed of sand, silt, clay, and tap water, on varying bed slopes of 6°, 8°, and 9.5°, and with discharge rates of 10[m3/h] and 15[m3/h]. Stress-controlled rheometry experiments were performed on the mixtures to obtain apparent viscosity data. A classification was developed based on the imposed flow conditions, where a cohesive flow may fall within one of five distinct flow types: 1) a cohesive plug flow (PF) with a laminar free shear and boundary layers, 2) a top transitional plug flow (TTPF) containing a turbulent free shear layer, a plug layer, and a laminar boundary layer, 3) a complete transitional plug flow (CTPF) consisting of a turbulent free shear and boundary layers and a plug, 4) a transitional turbidity current (TTC) with a turbulent free shear layer and a laminar boundary layer, and, 5) a completely turbulent turbidity current (TC). During the experiments, flow type PF resulted in en masse deposition of a thick uniform ungraded muddy sand mixture, which was emplaced once the yield stress overcame the gravitational forces within the tail region of the flow. Flow type TTPF resulted in deposition of a thin ungraded basal clean sand layer during the run. This layer was covered by a muddy sand deposit from the tail. Flow type TTC did not deposit any sediment during the run. A uniform muddy sand mixture was emplaced by the tail of the flow. Flow type TC resulted in deposition of poorly sorted massive bottom sand layer. This layer was overlain by either a muddy sand mixture or a sand and silt planar lamination. Flow type CTPF was not observed during the experiments. Furthermore, it was observed that flows which are in transition from a TTC to a TTPF result in a thin bottom clean sand layer covered by a banded transitional interval. This was overlain by a muddy sand layer and a very thin clean sand layer, resulting from traction by dilute turbulent wake. In all cases a mud cap was emplaced on top of the deposit after the runs were terminated.

The Effect of Bioturbation on Relative Paleointenstiy Records

NASA Astrophysics Data System (ADS)

Egli, R.; Zhao, X.; Gilder, S. A.

2015-12-01

Bioturbation is one of the key factors affecting the acquisition of a natural remanent magnetization (NRM) in sediments featuring a top mixed layer. In this case, a rotational diffusion process controls the acquisition timing, which is described in terms of a lock-in function, and NRM intensity. In general terms, NRM acquisition by rotational diffusion is described by a Smoluchowski-Debye differential equation, which yields analytical solutions describing how an initially acquired depositional remanent magnetization (DRM) is progressively replaced by a post-depositional remanent magnetization (PDRM) [Egli and Mao, Geochem. Geophys. Geosyst. 16, 995-1016, 2015]. These solutions in turn support the calculation of lock-in functions. Results are controlled by the following parameters: (1) a rotation diffusivity constant γ = 2DrL/ω, where Dr is the rotational diffusion coefficient, L the thickness of the mixed layer, and ω the sedimentation rate, and (2) the ratio between magnetic aligning torques τm = mB and the torques τp associated with mechanical interactions between sediment particles and with the action of perturbing forces. The PDRM acquisition rate and the extent of DRM replacement is controlled by γ, while PDRM intensity is a Langevin function of τm/ τp. Associated lock-in functions range from a constant (NRM is acquired only at the sediment surface) to the classical lock-in function starting below the mixed layer, though intermediate situations where PDRM is partially acquired in the mixed layer. This model has been confirmed by redeposition experiments performed with fresh sediment containing living microorganisms. Redeposition experiments show that the intensity of bioturbation-driven PDRMs can reach ~50% of the originally acquired DRM. Our model has profound consequences for the evaluation of relative paleointensity records, where variations can be driven by changes of the depositional environment. While this knowledge is not new, we provide for the first time a key for understanding, in a quantitative manner, how the NRM acquisition efficiency is controlled by bioturbation. A combination of proxies leading to estimates of the bioturbation activity might provide a new path for improving the reliability of relative paleointensity records.

A combined model for Sediment TRansport In Coastal Hazard Events (GeoClaw-STRICHE): Theoretical formulation and validation

NASA Astrophysics Data System (ADS)

Tang, H.; Weiss, R.

2016-12-01

GeoClaw-STRICHE is designed for simulating the physical impacts of tsunami as it relates to erosion, transport and deposition. GeoClaw-STRICHE comprises GeoClaw for the hydrodynamics and the sediment transport model we refer to as STRICHE, which includes an advection diffusion equation as well as bed-updating. Multiple grain sizes and sediment layers are added into GeoClaw-STRICHE to simulate grain-size distribution and add the capability to develop grain-size trends from bottom to the top of a simulated deposit as well as along the inundation. Unlike previous models based on empirical equations or sediment concentration gradient, the standard Van Leer method is applied to calculate sediment flux. We tested and verified GeoClaw-STRICHE with flume experiment by Johnson et al. (2016) and data from the 2004 Indian Ocean tsunami in Kuala Meurisi as published in Apotsos et al. (2011). The comparison with experimental data shows GeoClaw-STRICHE's capability to simulate sediment thickness and grain-size distribution in experimental conditions, which builds confidence that sediment transport is correctly predicted by this model. The comparison with the data from the 2004 Indian Ocean tsunami reveals that the pattern of sediment thickness is well predicted and is of similar quality, if not better than the established computational models such as Delft3D.

Geochemical, radiometric, and environmental approaches for the assessment of the intensity and chronology of metal contamination in the sediment cores from Oualidia lagoon (Morocco).

PubMed

Mejjad, Nezha; Laissaoui, Abdelmourhit; El-Hammoumi, Ouafa; Fekri, Ahmed; Amsil, Hamid; El-Yahyaoui, Adil; Benkdad, Azzouz

2018-06-01

The present study evaluates the distribution of metals over the last 100 years in the Oualidia lagoon by examining their concentrations in the sediment cores. The samples were analyzed by instrumental neutron activation analysis and inductively coupled plasma mass spectrometry. Activities of 210 Pb, 226 Ra, and 137 Cs were determined by gamma-ray spectrometry for establishing the age-depth relationships throughout the sediment cores by applying conventional models. The results indicated that the study area is contaminated by As and Cd revealing a detectable anthropogenic input of occurring metals as a consequence of the continuous development of human activities around the lagoon since 1950. The enrichment factor calculated for each layer of the three cores revealed that the studied sediments present no enrichment by Pb, K, and Mn; minor enrichment by Zn, Cr, Co, Cu, V, and Ni; and a moderately to severe enrichment by As and Cd. The pollution load index values increase from the bottom to the top of cores, and ranged from 0.9 to 2.8, which indicates levels of pollutants ranging from background to relatively high concentrations in the investigated sediments.

Diversity of Microbial Communities and Quantitative Chemodiversity in Layers of Marine Sediment Cores from a Causeway (Kaichu-Doro) in Okinawa Island, Japan.

PubMed

Soliman, Taha; Reimer, James D; Yang, Sung-Yin; Villar-Briones, Alejandro; Roy, Michael C; Jenke-Kodama, Holger

2017-01-01

Microbial community diversity and chemodiversity were investigated in marine sediments adjacent to the Okinawan "Kaichu-Doro" Causeway, which was constructed 46 years ago to connect a group of four islands (Henza-jima, Miyagi-jima, Ikei-jima, Hamahiga-jima) to the Okinawan main island. This causeway was not built on pilings, but by land reclamation; hence, it now acts as a long, thin peninsula. The construction of this causeway was previously shown to have influenced the surrounding marine ecosystem, causing ecosystem fragmentation and loss of water circulation. In this study, we collected sediment cores ( n = 10) from five paired sites in 1 m water depths. Each pair of sites consisted of one site each on the immediate north and south sides of the causeway. Originally the members of each pair were much closer to each other (<150 m) than to other pairs, but now the members of each pair are isolated by the causeway. Each core was 60-80 cm long and was divided into 15-cm layers. We examined the vertical diversity of microbial communities and chemical compounds to determine the correlation between chemodiversity and microbial communities among marine sediment cores and layers. Principal coordinate analyses (PCoA) of detected compounds and of bacterial and archaeal operational taxonomic units (OTUs) revealed that the north and south sides of the causeway are relatively isolated, with each side having unique microbial OTUs. Additionally, some bacterial families (e.g., Acidaminobacteraceae, Rhizobiaceae, and Xanthomonadaceae) were found only on the south side of Kaichu-Doro. Interestingly, we found that the relative abundance of OTUs for some microbial families increased from top to bottom, but this was reversed in some other families. We conclude that the causeway has altered microbial community composition and metabolite profiles in marine sediments.

Measuring Fast-Temporal Sediment Fluxes with an Analogue Acoustic Sensor: A Wind Tunnel Study

PubMed Central

Poortinga, Ate; van Minnen, Jan; Keijsers, Joep; Riksen, Michel; Goossens, Dirk; Seeger, Manuel

2013-01-01

In aeolian research, field measurements are important for studying complex wind-driven processes for land management evaluation and model validation. Consequently, there have been many devices developed, tested, and applied to investigate a range of aeolian-based phenomena. However, determining the most effective application and data analysis techniques is widely debated in the literature. Here we investigate the effectiveness of two different sediment traps (the BEST trap and the MWAC catcher) in measuring vertical sediment flux. The study was performed in a wind tunnel with sediment fluxes characterized using saltiphones. Contrary to most studies, we used the analogue output of five saltiphones mounted on top of each other to determine the total kinetic energy, which was then used to calculate aeolian sediment budgets. Absolute sediment losses during the experiments were determined using a balance located beneath the test tray. Test runs were conducted with different sand sizes and at different wind speeds. The efficiency of the two traps did not vary with the wind speed or sediment size but was affected by both the experimental setup (position of the lowest trap above the surface and number of traps in the saltation layer) and the technique used to calculate the sediment flux. Despite this, good agreement was found between sediment losses calculated from the saltiphone and those measured using the balance. The results of this study provide a framework for measuring sediment fluxes at small time resolution (seconds to milliseconds) in the field. PMID:24058512

Measuring fast-temporal sediment fluxes with an analogue acoustic sensor: a wind tunnel study.

PubMed

Poortinga, Ate; van Minnen, Jan; Keijsers, Joep; Riksen, Michel; Goossens, Dirk; Seeger, Manuel

2013-01-01

In aeolian research, field measurements are important for studying complex wind-driven processes for land management evaluation and model validation. Consequently, there have been many devices developed, tested, and applied to investigate a range of aeolian-based phenomena. However, determining the most effective application and data analysis techniques is widely debated in the literature. Here we investigate the effectiveness of two different sediment traps (the BEST trap and the MWAC catcher) in measuring vertical sediment flux. The study was performed in a wind tunnel with sediment fluxes characterized using saltiphones. Contrary to most studies, we used the analogue output of five saltiphones mounted on top of each other to determine the total kinetic energy, which was then used to calculate aeolian sediment budgets. Absolute sediment losses during the experiments were determined using a balance located beneath the test tray. Test runs were conducted with different sand sizes and at different wind speeds. The efficiency of the two traps did not vary with the wind speed or sediment size but was affected by both the experimental setup (position of the lowest trap above the surface and number of traps in the saltation layer) and the technique used to calculate the sediment flux. Despite this, good agreement was found between sediment losses calculated from the saltiphone and those measured using the balance. The results of this study provide a framework for measuring sediment fluxes at small time resolution (seconds to milliseconds) in the field.

Total Mercury and Methylmercury Response in Water, Sediment, and Biota to Destratification of the Great Salt Lake, Utah, United States.

PubMed

Valdes, Carla; Black, Frank J; Stringham, Blair; Collins, Jeffrey N; Goodman, James R; Saxton, Heidi J; Mansfield, Christopher R; Schmidt, Joshua N; Yang, Shu; Johnson, William P

2017-05-02

Measurements of chemical and physical parameters made before and after sealing of culverts in the railroad causeway spanning the Great Salt Lake in late 2013 documented dramatic alterations in the system in response to the elimination of flow between the Great Salt Lake's north and south arms. The flow of denser, more-saline water through the culverts from the north arm (Gunnison Bay) to the south arm (Gilbert Bay) previously drove the perennial stratification of the south arm and the existence of oxic shallow brine and anoxic deep brine layers. Closure of the causeway culverts occurred concurrently with a multiyear drought that resulted in a decrease in the lake elevation and a concomitant increase in top-down erosion of the upper surface of the deep brine layer by wind-forced mixing. The combination of these events resulted in the replacement of the formerly stratified water column in the south arm with one that was vertically homogeneous and oxic. Total mercury concentrations in the deep waters of the south arm decreased by approximately 81% and methylmercury concentrations in deep waters decreased by roughly 86% due to destratification. Methylmercury concentrations decreased by 77% in underlying surficial sediment, whereas there was no change observed in total mercury. The dramatic mercury loss from deep waters and methylmercury loss from underlying sediment in response to causeway sealing provides new understanding of the potential role of the deep brine layer in the accumulation and persistence of methylmercury in the Great Salt Lake. Additional mercury measurements in biota appear to contradict the previously implied connection between elevated methylmercury concentrations in the deep brine layer and elevated mercury in avian species reported prior to causeway sealing.

Across-canyon movement of earthquake-induced sediment gravity flow offshore southwestern Taiwan.

NASA Astrophysics Data System (ADS)

Chen, Yen-Ting; Su, Chih-Chieh; Lu, Yi-Wei; Cheng, Yiya

2017-04-01

Caused by the origin of oblique collision between the Eurasian and Philippine Sea Plate, Taiwan Island inevitably faces the destiny to be continuously influenced by frequent and severe earthquake activities. Thus, earthquake-induced sediment gravity flows are common marine geo-hazards in the submarine region of Taiwan. The Pingtung Doublet earthquakes occurred in Dec. 2006 offshore Fangliao Township and two submarine cables were broken at the Fangliao Submarine Canyon (FLSC) head, simultaneously. On the eastern side of the FLSC head, chirp sonar profiles and high-resolution bathymetry data revealed linear seafloor failures along the northwest direction and merged into the FLSC. Moreover, cores taken from the seafloor failure area and in the FLSC also observed thick debrite and turbidite layers at core tops. Nevertheless, in the western side of the FLSC head, local fishermen reported disturbed water just after the Pingtung Doublet earthquakes. Hence series of cores and chirp sonar data were collected at the western side of the FLSC, trying to figure out the linkage of Pingtung Doublet earthquakes induced gravity flow deposits on both sides of the FLSC. The analysis results suggest that the deposits of disturbed water at the western side of FLSC head was caused by the finer suspended sediments separated from the main body at the top of the gravity flow. Our results point out besides the traditional well-known downward transportation in the canyon, the across-canyon movement may also leave stratigraphic records and help us to establish a more complete transportation process of a sediment gravity flow.

Neogene basin infilling from cosmogenic nuclides (10Be and 21Ne) in Atacama, Chile

NASA Astrophysics Data System (ADS)

Sanchez, Caroline; Regard, Vincent; Carretier, Sébastien; Riquelme, Rodrigo; Blard, Pierre-Henri; Campos, Eduardo; Brichau, Stéphanie; Lupker, Marteen; Hérail, Gérard

2017-04-01

In the hyperarid Atacama Desert, northern Chile, Neogene sediments host copper rich layers (exotic supergene mineralization). Current mines are excavated into relatively thin (<200-300 m) Neogene basins whose infilling chronology is poorly constrained. We took advantage of one of these mining pits, and sampled for 10Be and 21Ne cosmogenic nuclide dosing. These cosmogenic nuclides help constraining the infilling chronology. Indeed, basin sediments were deposited with a cosmogenic nuclide content acquired on hillslopes. Then within the basin, cosmogenic nuclide concentrations evolved through the competing production (quickly decreasing with depth) and disintegration (not for 21Ne). Sampling depths are at ˜100 m and at ˜50 m below the desert surface. First, 21Ne gives lower boundaries for upstream erosion rates or local sedimentation rate. These bounds are between 2 and 10 m/Ma, which is quite important for the area. The ratio between the two cosmogenic nuclides indicate a maximum burial age of 12 Ma (minimal erosion rate of 15 m/Ma) and is surprisingly similar from bottom to top, indicating a probable rapid infilling. We finally processed a Monte-Carlo inversion. This inversion helps taking into account the post-deposition muonic production of cosmogenic nuclides. Inversion results is dependent on the muonic production scheme. Interestingly, the similarity in concentrations from bottom to top pleads for quite low production at depth. Our data finally indicates a quick infilling between 12.5 and 10 Ma BP accounting for ˜100 m of deposition (minimum sedimentation rate of 40 m/Ma).

Transient electromagnetic study of basin fill sediments in the Upper San Pedro Basin, Mexico

USGS Publications Warehouse

Bultman, M.W.; Gray, F.

2011-01-01

The Upper San Pedro River Basin in Mexico and the United States is an important riparian corridor that is coming under increasing pressure from growing populations and the associated increase in groundwater withdrawal. Several studies have produced three-dimensional maps of the basin fill sediments in the US portion of the basin but little work has been done in the Mexican portion of the basin. Here, the results of a ground-based transient electromagnetic (TEM) survey in the Upper San Pedro Basin, Mexico are presented. These basin fill sediments are characterized by a 10-40 m deep unsaturated surficial zone which is composed primarily of sands and gravels. In the central portion of the basin this unsaturated zone is usually underlain by a shallow clay layer 20-50 m thick. Beneath this may be more clay, as is usually the case near the San Pedro River, or interbedded sand, silt, and clay to a depth of 200-250 m. As you move away from the river, the upper clay layer disappears and the amount of sand in the sediments increases. At 1-2 km away from the river, sands can occupy up to 50% of the upper 200-250 m of the sediment fill. Below this, clays are always present except where bedrock highs are observed. This lower clay layer begins at a depth of about 200 m in the central portion of the basin (250 m or more at distances greater than 1-2 km from the river) and extends to the bottom of most profiles to depths of 400 m. While the depth of the top of this lower clay layer is probably accurate, its thickness observed in the models may be overestimated due to the relatively low magnetic moment of the TEM system used in this study. The inversion routine used for interpretation is based on a one-dimensional geologic model. This is a layer based model that is isotropic in both the x and y directions. Several survey soundings did not meet this requirement which invalidates the inversion process and the resulting interpretation at these locations. The results from these locations were rejected. ?? 2011 Springer-Verlag (outside the USA).

New insights into the paleolake sequence of Baumkirchen (Austria): multiple lake phases and a minor ice advance during MIS 4?

NASA Astrophysics Data System (ADS)

Barrett, Samuel; Starnberger, Reinhard; Spötl, Christoph; Brauer, Achim; Tjallingii, Rik; Dulski, Peter; Abfalterer, Christof

2015-04-01

The sequence of pre-LGM lacustrine sediments at Baumkirchen (Austria) provides a key record in Alpine Quaternary stratigraphy. These sediments from within the boundary of the Alps potentially provide unique insights into the regional paleoclimate. Recent drilling revealed at least ~250m (the base was not reached) of almost entirely mm- to cm-scale lacustrine sediments. The laminated sediments are comprised of alternations between clayey silt and event layers of medium silt to fine sand. The sequence is interrupted only by a short section of gravel supported in an unlaminated clay-rich matrix. Optically stimulated luminescence dating identifies two distinct sequences: the upper sequence spanning mid-late Marine Isotope Stage (MIS) 3 (~33 to ~45 ka BP), agreeing with existing calibrated radiocarbon ages, and the lower section dating to MIS 4 (~59 to ~73 ka BP). Whether the hiatus is an erosional unconformity, or if the sequences represent two separate lake phases is unclear. Although the precise location of the hiatus is hard to identify, the gravel-rich section lies at the very top of the lower sequence. Pebbles in these gravels are largely angular and contain a significant proportion of non-local, regional lithologies. Such gravels are absent in the remainder of the entire 250 m-thick sequence and hence suggest a unique event rather than e.g. an interfingering local delta gravel foresets with the basin sediments. The gravels are therefore likely to be ice-rafted debris from icebergs from nearby glaciers calving into the lake. This therefore represents the first sedimentological evidence of a MIS 4 ice advance in the Eastern Alps. X-ray fluorescence analysis (ITRAX core scanning) of event layers indicates a strong change in the geochemical composition from generally K, Zr and Ti-rich layers in the upper sequence to mainly Ca and/or Si-rich layers in the lower sequence. X-ray diffraction analysis shows the Ca and Si signals to be controlled by carbonate (both calcite and dolomite) and quartz, respectively. This suggests a change in dominant sediment source and may indicate a change in catchment or paleolake configuration, re-raising the long outstanding question of how the lake or lakes were dammed.

Vertical and lateral flux on the continental slope off Pakistan: correlation of sediment core and trap results

NASA Astrophysics Data System (ADS)

Schulz, H.; von Rad, U.

2014-06-01

Due to the lack of bioturbation, the varve-laminated muds from the oxygen minimum zone (OMZ) off Pakistan provide a unique opportunity to precisely determine the vertical and lateral sediment fluxes in the nearshore part of the northeastern Arabian Sea. West of Karachi (Hab area), the results of two sediment trap stations (EPT and WPT) were correlated with 16 short sediment cores on a depth transect crossing the OMZ. The top of a distinct, either reddish- or light-gray silt layer, 210Pb-dated as AD 1905 ± 10, was used as an isochronous stratigraphic marker bed to calculate sediment accumulation rates. In one core, the red and gray layer were separated by a few (5-10) thin laminae. According to our varve model, this contributes < 10 years to the dating uncertainty, assuming that the different layers are almost synchronous. We directly compared the accumulation rates with the flux rates from the sediment traps that collected the settling material within the water column above. All traps on the steep Makran continental slope show exceptionally high, pulsed winter fluxes of up to 5000 mg m-2 d-1. Based on core results, the flux at the seafloor amounts to 4000 mg m-2 d-1 and agrees remarkably well with the bulk winter flux of material, as well as with the flux of the individual bulk components of organic carbon, calcium carbonate and opal. However, due to the extreme mass of remobilized matter, the high winter flux events exceeded the capacity of the shallow traps. Based on our comparisons, we argue that high-flux events must occur regularly during winter within the upper OMZ off Pakistan to explain the high accumulations rates. These show distribution patterns that are a negative function of water depth and distance from the shelf. Some of the sediment fractions show marked shifts in accumulation rates near the lower boundary of the OMZ. For instance, the flux of benthic foraminifera is lowered but stable below ~1200-1300 m. However, flux and sedimentation in the upper eastern Makran area are dominated by the large amount of laterally advected fine-grained material and by the pulsed nature of the resuspension events at the upper margin during winter.

The last glacial cycle documented on the Lower Bengal Fan - chronological and paleoclimate implications

NASA Astrophysics Data System (ADS)

Weber, M. E.; Dekens, P.; Reilly, B.; Lantzsch, H.; Selkin, P. A.; Das, S. K.; Williams, T.; Martos, Y. M.; Adhikari, R. R.; Gyawali, B. R.; Jia, G.; Fox, L. R.; Ge, J.; Manoj, M. C.; Savian, J. F.; Meynadier, L.; Spiess, V.; France-Lanord, C.; Klaus, A.

2016-12-01

IODP Expedition 354 set out in February to March 2015 to drill seven sites along an east west oriented core transect of 320 km length at 8°N in the Bengal Fan (France-Lanord et al., 2015). Sediments show complex intercalation of turbiditic and hemipelagic deposits, documenting the interaction of fan evolution and paleoceanographic history. Hemipelagic sequences represent a several meter thick top layer of Late Quaternary sediment. Deposits are either rich in biogenic opal/clay or in carbonate. We studied physical, optical, geochemical, grain-size, and stable isotopic properties of this top layer to establish a time frame, estimate sedimentary properties, and assess the development of the region during the last glacial cycle. For this purpose, we sampled Site U1452C-1H continuously for the uppermost 480 cm in 2-cm increments. Preliminary results indicate the Toba Ash 1 (74 ka) is a distinct time marker in most physical property data sets. Records of wet-bulk density as well as color reflectance b* (the red-green component) and L* (the lightness) show a dominant precession cyclicity. Hence, we are able to provide an insolation-tuned chronology for the last 200 ka (MIS1 - 7). These records agree well with d18O records retrieved from Chinese caves. An independent age model is derived from records of relative paleointensity (RPI), including the assessment of the Laschamp Event ( 40 ka), and on RPI tuning to global templates. We will compare both chronologies and evaluate their chronological and paleoclimatic implications. We will also present preliminary grain-size and paleoceanographic proxy data (sea-surface temperature, sea-surface salinity, and Mg/Ca) as well as color endmember modeling to reconstruct ice volume, marine biological productivity, nutrient supply, and deep-water circulation. The sedimentologic, oceanographic and climatic conditions are linked to changes in monsoonal strength and terrestrial input, which will also be studied using sedimentary proxies to reconstruct chemical weathering, sediment sources, and transport time. Our work addresses primary cruise objectives - linking monsoon variability, regional and global climate, and Bay of Bengal sediment deposition.

Methane production from bicarbonate and acetate in an anoxic marine sediment

NASA Technical Reports Server (NTRS)

Crill, P. M.; Martens, C. S.

1986-01-01

Methane production from C-14 labeled bicarbonate and acetate was measured over the top 28 cm of anoxic Cape Lookout Bight sediments during the summer of 1983. The depth distribution and magnitude of summed radioisotopically determined rates compare well with previous measurements of total methane production and the sediment-water methane flux. Methane production from CO2 reduction and acetate fermentation accounts for greater than 80 percent of the total production rate and sediment-water flux. Methane production from bicarbonate was found to occur in all depth intervals sampled except those in the top 2 cm, whereas significant methane production from acetate only occurred at depths below 10 cm where sulfate was exhausted. Acetate provided 20 to 29 percent of the measured methane production integrated over the top 30 cm of the sediments.

Syn- and post-sedimentary controls on clay mineral assemblages in a tectonically active basin, Andean Argentinean foreland

NASA Astrophysics Data System (ADS)

Do Campo, Margarita; Nieto, Fernando; del Papa, Cecilia; Hongn, Fernando

2014-07-01

In the northern part of the Calchaquí Valley (NW Argentina), Palaeogene Andean foreland sediments are represented by a 1400-metre-thick continental succession (QLC: Quebrada de Los Colorados Formation) consisting of claystones, siltstones, sandstones, and conglomerates representing sedimentation in fluvial-alluvial plains and alluvial fan settings. To understand the main syn- and postsedimentary variables controlling the clay mineral assemblages of this succession, we have studied the fine-grained clastic sediments by X-ray diffraction and electron microscopy, along with a detailed sedimentary facies analysis, for two representative sections. In the northern section, the whole succession was sampled and analysed by XRD, whereas in the second section, a control point 15 km to the south, only the basal levels were analysed. The XRD study revealed a strong contrast in clay mineral assemblages between these two sections as well as with sections in the central Calchaquí Valley studied previously. In the northernmost part of the study area, a complete evolution from smectite at the top to R3 illite/smectite mixed-layers plus authigenic kaolinite at the bottom, through R1-type mixed-layers in between, has been recognized, indicating the attainment of late diagenesis. In contrast, the clay mineral assemblages of equivalent foreland sediments cropping out only 15 km to the south contain abundant smectite and micas, subordinate kaolinite and chlorite, and no I/S mixed-layers to the bottom of the sequence. Early diagenetic conditions were also inferred in a previous study for equivalent sediments of the QLC Formation cropping out to the south, in the central Calchaquí Valley, as smectite occurs in basal strata. Burial depths of approximately 3000 m were estimated for the QLC Formation in the central and northern Calchaquí Valley; in addition, an intermediate to slightly low geothermal gradient can be considered likely for both areas as foreland basins are regarded as hypothermal basins. Consequently, the attainment of late diagenesis in the northernmost study area cannot be explained by significant differences in burial depth nor in geothermal gradient in relation to the section 15 km to the south nor with the central Calchaquí Valley. The formation of R3 mixed-layer I/S and authigenic kaolinite in the northern study area was most likely controlled by the circulation of hot, deep fluids along the reverse faults that bounded the Calchaquí valley. These faults were active during the Cenozoic, as evidenced by the syndepositional deformation features preserved in the studied sediments. Stress could also have been a driving force in burial diagenesis at the R3 mixed-layer I/S stage in these young continental sediments.

Depositional dynamics in the El'gygytgyn Crater margin: implications for the 3.6 Ma old sediment archive

NASA Astrophysics Data System (ADS)

Schwamborn, G.; Fedorov, G.; Ostanin, N.; Schirrmeister, L.; Andreev, A.; El'gygytgyn Scientific Party, the

2012-11-01

The combination of permafrost history and dynamics, lake level changes and the tectonical framework is considered to play a crucial role for sediment delivery to El'gygytgyn Crater Lake, NE Russian Arctic. The purpose of this study is to propose a depositional framework based on analyses of the core strata from the lake margin and historical reconstructions from various studies at the site. A sedimentological program has been conducted using frozen core samples from the 141.5 m long El'gygytgyn 5011-3 permafrost well. The drill site is located in sedimentary permafrost west of the lake that partly fills the El'gygytgyn Crater. The total core sequence is interpreted as strata building up a progradational alluvial fan delta. Four macroscopically distinct sedimentary units are identified. Unit 1 (141.5-117.0 m) is comprised of ice-cemented, matrix-supported sandy gravel and intercalated sandy layers. Sandy layers represent sediments which rained out as particles in the deeper part of the water column under highly energetic conditions. Unit 2 (117.0-24.25 m) is dominated by ice-cemented, matrix-supported sandy gravel with individual gravel layers. Most of the Unit 2 diamicton is understood to result from alluvial wash and subsequent gravitational sliding of coarse-grained (sandy gravel) material on the basin slope. Unit 3 (24.25-8.5 m) has ice-cemented, matrix-supported sandy gravel that is interrupted by sand beds. These sandy beds are associated with flooding events and represent near-shore sandy shoals. Unit 4 (8.5-0.0 m) is ice-cemented, matrix-supported sandy gravel with varying ice content, mostly higher than below. It consists of slope material and creek fill deposits. The uppermost metre is the active layer (i.e. the top layer of soil with seasonal freeze and thaw) into which modern soil organic matter has been incorporated. The nature of the progradational sediment transport taking place from the western and northern crater margins may be related to the complementary occurrence of frequent turbiditic layers in the central lake basin, as is known from the lake sediment record. Slope processes such as gravitational sliding and sheet flooding occur especially during spring melt and promote mass wasting into the basin. Tectonics are inferred to have initiated the fan accumulation in the first place and possibly the off-centre displacement of the crater lake.

Denitrification potential in relation to lithology in five headwater riparian zones.

PubMed

Hill, Alan R; Vidon, Philippe G F; Langat, Jackson

2004-01-01

The influence of riparian zone lithology on nitrate dynamics is poorly understood. We investigated vertical variations in potential denitrification activity in relation to the lithology and stratigraphy of five headwater riparian zones on glacial till and outwash landscapes in southern Ontario, Canada. Conductive coarse sand and gravel layers occurred in four of the five riparian areas. These layers were thin and did not extend to the field-riparian perimeter in some riparian zones, which limited their role as conduits for ground water flow. We found widespread organic-rich layers at depths ranging from 40 to 300 cm that resulted from natural floodplain processes and the burial of surface soils by rapid valley-bottom sedimentation after European settlement. The organic matter content of these layers varied considerably from 2 to 5% (relic channel deposit) to 5 to 21% (buried soils) and 30 to 62% (buried peat). Denitrification potential (DNP) was measured by the acetylene block method in sediment slurries amended with nitrate. The highest DNP rates were usually found in the top 0- to 15-cm surface soil layer in all riparian zones. However, a steep decline in DNP with depth was often absent and high DNP activity occurred in the deep organic-rich layers. Water table variations in 2000-2002 indicated that ground water only interacted frequently with riparian surface soils between late March and May, whereas subsurface organic layers that sustain considerable DNP were below the water table for most of the year. These results suggest that riparian zones with organic deposits at depth may effectively remove nitrate from ground water even when the water table does not interact with organic-rich surface soil horizons.

Characterization of a complex near-surface structure using well logging and passive seismic measurements

NASA Astrophysics Data System (ADS)

Benjumea, Beatriz; Macau, Albert; Gabàs, Anna; Figueras, Sara

2016-04-01

We combine geophysical well logging and passive seismic measurements to characterize the near-surface geology of an area located in Hontomin, Burgos (Spain). This area has some near-surface challenges for a geophysical study. The irregular topography is characterized by limestone outcrops and unconsolidated sediments areas. Additionally, the near-surface geology includes an upper layer of pure limestones overlying marly limestones and marls (Upper Cretaceous). These materials lie on top of Low Cretaceous siliciclastic sediments (sandstones, clays, gravels). In any case, a layer with reduced velocity is expected. The geophysical data sets used in this study include sonic and gamma-ray logs at two boreholes and passive seismic measurements: three arrays and 224 seismic stations for applying the horizontal-to-vertical amplitude spectra ratio method (H/V). Well-logging data define two significant changes in the P-wave-velocity log within the Upper Cretaceous layer and one more at the Upper to Lower Cretaceous contact. This technique has also been used for refining the geological interpretation. The passive seismic measurements provide a map of sediment thickness with a maximum of around 40 m and shear-wave velocity profiles from the array technique. A comparison between seismic velocity coming from well logging and array measurements defines the resolution limits of the passive seismic techniques and helps it to be interpreted. This study shows how these low-cost techniques can provide useful information about near-surface complexity that could be used for designing a geophysical field survey or for seismic processing steps such as statics or imaging.

Soil sealing and vesicular layer formation as initial structure development and its effect on infiltration

NASA Astrophysics Data System (ADS)

Badorreck, A.; Gerke, H. H.; Weller, U.; Vontobel, P.

2009-04-01

In the Lusatia mining district (NE-Germany) an artificial catchment was constructed to study initial ecosystem development and runoff generation. As a key process in this early stage, we investigate the surface structure dynamics as it strongly influences erosion, infiltration, matter dynamics, and vegetation establishment. The presented work focuses on observations of soil pore structure formation at the surface at five sites in the catchment and in an adjacent "younger" area composed of comparable sediments. Moreover we've conducted infiltration experiments in the lab and field to relate the soil pore structure to the hydraulic properties. The surface soil was sampled in cylindrical rings (10 cm³) down to 2 cm depth from which bulk density profiles were obtained using X-ray computed tomography (CT) (at UFZ- Halle, Germany) with a resolution of 0.084 mm. The influence of structure on infiltration was investigated using neutron radiography (at the NEUTRA facility of the Paul-Scherrer-Institut, Villigen, Switzerland) to visualise two-dimensional (2D) infiltration patterns. The slab-type samples were equilibrated to different initial water contents and then exposed to drip irrigation (to simulate rainfall) while a series of neutron radiographs were taken. In addition, field measurements with a miniature tension infiltrometer were conduced. The micro-tomographies exhibit formation of surface sealing whose thickness and intensity vary with silt and clay content. The CT images show several coarser- and finer-textured micro-layers at the sample surfaces that were formed as a consequence of repeated washing in of finer particles in underlying coarser sediment. In micro-depressions, the uppermost layers consist of sorted fine sand and silt due to wind erosion. Similar as for desert pavements, a vesicular pore structure developed in these sediments on top, but also scattered in fine sand- and silt-enriched micro-layers. The infiltration rates were severely affected by the surface crusts; however, the rates were independent of the vesicular pore layer.

Seismic Characterization of Silica Diagenesis in the Northwestern Pacific

NASA Astrophysics Data System (ADS)

Greene, J. A.; Lizarralde, D.; Tominaga, M.; Tivey, M.

2017-12-01

We use seismic reflection data to investigate the silica diagenesis that converted siliceous ooze into the widespread chert/porcellanite layer in the northwestern Pacific. In particular, we investigate whether this process is currently ongoing in the oldest lithosphere of the Pacific. We present images of seismic reflection data collected during the R/V Thomas G. Thompson cruise TN272 and processed using a velocity model constructed from concurrently collected sonobuoy refraction data, applying a normal moveout correction and stack, post-stack Kirchhoff time migration, and predictive gap deconvolution. We compare our seismic observations of the chert/porcellanite layer with nearby drill holes and analogous studies of silica diagenesis around the world. In the processed seismic data, we identify a previously unobserved short-wavelength depth variation to a prominent reflector representing the top of the chert/porcellanite layer, with a vertical change in this horizon of 20 m. This short-wavelength character is in contrast to the flat, seafloor parallel character more typical of the regional chert/porcellanite reflector and may be indicative of the active transformation of siliceous ooze to chert/porcellanite. Drill results in the northwestern Pacific document little to no siliceous ooze above the chert/porcellanite layer; however, they have extremely low recovery rates that could have failed to sample this sediment. No folding or reflector offsets indicative of faulting are observed above or below the short-wave character of the chert/porcellanite reflector, suggesting a structural origin is unlikely, nor are the surrounding reflectors disturbed, as would be expected if these features were caused by fluid expulsion. Instead, the short-wavelength depth variation in the chert/porcellanite layer may be the result of differential advancement of the silica diagenetic front where the siliceous ooze to chert/porcellanite reaction locally occurs in shallower sediments, as has been seismically observed in settings around the world. This could indicate that silica diagenesis is currently ongoing in the northwestern Pacific, and that siliceous ooze remains present in the overlying sediment for conversion to chert/porcellanite.

Site-dependent proxy response to climate change during the last 140 years observed in varved lake sediments in Northern Poland

NASA Astrophysics Data System (ADS)

Ott, Florian; Kramkowski, Mateusz; Wulf, Sabine; Plessen, Birgit; Serb, Johanna; Tjallingii, Rik; Schwab, Markus; Słowiński, Michał; Brykała, Dariusz; Tyszkowski, Sebastian; Putyrskaya, Victoria; Appelt, Oona; Błaszkiewicz, Mirosław; Brauer, Achim

2017-04-01

This accurate dating and chronological correlation using crypto-tephras provide a powerful way to compare the varved sediment records of the lakes Głęboczek (JG), Czechowskie (JC) and Jelonek (JEL) (north-central Poland). For the last 140 years, high-resolution varve micro-facies analyses (seasonal layer composition and thickness) and µ-XRF element scanning as well as bulk geochemical analyses (TOC, CaCO3) at sub-decadal to decadal resolution were conducted for all three records. Varve chronologies have been independently established by means of annual layer counting. 137Cs activity concentration measurements confirmed the varve chronology from JC. The Askja AD1875 tephra has been used to synchronize the records. A comparison of sediment data with monthly temperature data from Koszalin since 1870 and daily temperature data from Chojnice since 1951 revealed different responses of lake deposition to recent temperature change. Varves are well-preserved over the entire 140 years only in the sediments of JG, while in the JC record two faintly varved intervals are intercalated and in JEL two non-varved intervals occur at the base and top of the profile. These differences likely are due to variations in lake characteristics. Climate changes at the demise of the Little Ice Age and the recent warming since the 1980s are expressed in varve micro-facies, CaCO3 and TOC contents in the three lakes with different response times and amplitudes. This allows us to discuss the role of local parameters like lake size, bathymetry and water depth in transferring climate change signals into lake sediment records. This study is a contribution to the Virtual Institute of Integrated Climate and Landscape Evolution Analyses - ICLEA - of the Helmholtz Association, grant number VH-VI-415.

16S rRNA Gene Survey of Microbial Communities in Winogradsky Columns

PubMed Central

Rundell, Ethan A.; Banta, Lois M.; Ward, Doyle V.; Watts, Corey D.; Birren, Bruce; Esteban, David J.

2014-01-01

A Winogradsky column is a clear glass or plastic column filled with enriched sediment. Over time, microbial communities in the sediment grow in a stratified ecosystem with an oxic top layer and anoxic sub-surface layers. Winogradsky columns have been used extensively to demonstrate microbial nutrient cycling and metabolic diversity in undergraduate microbiology labs. In this study, we used high-throughput 16s rRNA gene sequencing to investigate the microbial diversity of Winogradsky columns. Specifically, we tested the impact of sediment source, supplemental cellulose source, and depth within the column, on microbial community structure. We found that the Winogradsky columns were highly diverse communities but are dominated by three phyla: Proteobacteria, Bacteroidetes, and Firmicutes. The community is structured by a founding population dependent on the source of sediment used to prepare the columns and is differentiated by depth within the column. Numerous biomarkers were identified distinguishing sample depth, including Cyanobacteria, Alphaproteobacteria, and Betaproteobacteria as biomarkers of the soil-water interface, and Clostridia as a biomarker of the deepest depth. Supplemental cellulose source impacted community structure but less strongly than depth and sediment source. In columns dominated by Firmicutes, the family Peptococcaceae was the most abundant sulfate reducer, while in columns abundant in Proteobacteria, several Deltaproteobacteria families, including Desulfobacteraceae, were found, showing that different taxonomic groups carry out sulfur cycling in different columns. This study brings this historical method for enrichment culture of chemolithotrophs and other soil bacteria into the modern era of microbiology and demonstrates the potential of the Winogradsky column as a model system for investigating the effect of environmental variables on soil microbial communities. PMID:25101630

Pore fluid geochemistry from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

USGS Publications Warehouse

Torres, M.E.; Collett, T.S.; Rose, K.K.; Sample, J.C.; Agena, W.F.; Rosenbaum, E.J.

2011-01-01

The BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well was drilled and cored from 606.5 to 760.1. m on the North Slope of Alaska, to evaluate the occurrence, distribution and formation of gas hydrate in sediments below the base of the ice-bearing permafrost. Both the dissolved chloride and the isotopic composition of the water co-vary in the gas hydrate-bearing zones, consistent with gas hydrate dissociation during core recovery, and they provide independent indicators to constrain the zone of gas hydrate occurrence. Analyses of chloride and water isotope data indicate that an observed increase in salinity towards the top of the cored section reflects the presence of residual fluids from ion exclusion during ice formation at the base of the permafrost layer. These salinity changes are the main factor controlling major and minor ion distributions in the Mount Elbert Well. The resulting background chloride can be simulated with a one-dimensional diffusion model, and the results suggest that the ion exclusion at the top of the cored section reflects deepening of the permafrost layer following the last glaciation (???100 kyr), consistent with published thermal models. Gas hydrate saturation values estimated from dissolved chloride agree with estimates based on logging data when the gas hydrate occupies more than 20% of the pore space; the correlation is less robust at lower saturation values. The highest gas hydrate concentrations at the Mount Elbert Well are clearly associated with coarse-grained sedimentary sections, as expected from theoretical calculations and field observations in marine and other arctic sediment cores. ?? 2009 Elsevier Ltd.

Magnetic Hysteresis of Deep-Sea Sediments in Korea Deep Ocean Study(KODOS) Area, NE Pacific

NASA Astrophysics Data System (ADS)

Kim, K.; Park, C.; Yoo, C.

2001-12-01

The KODOS area within the Clarion-Clipperton fracture zone (C-C zone) is surrounded by the Hawaiian and Line Island Ridges to the west and the central American continent to the east. Topography of the seafloor consists of flat-topped abyssal hills and adjacent abyssal troughs, both of which run parallel in N-S direction. Sediments from the study area consist mainly of biogenic sediments. Latitudinal zonation of sedimentary facies was caused by the accumulation of biogenic materials associated with the equatorial current system and movement of the Pacific plate toward the north or northwest. The KODOS area belongs to the latitudinal transition zone having depositional characteristics between non-fossiliferous pelagic clay-dominated zone and calcareous sediment-dominated zone. The box core sediments of the KODOS area are analyzed in an attempt to obtain magnetic hysteresis information and to elucidate the relationship between hysteresis property and lithological facies. Variations in magnetic hysteresis parameters with unit layers reflect the magnetic grain-size and concentrations within the sediments. The ratios of remanant coercivity/coercive force (Hcr/Hc) and saturation remnance/saturation magnetization (Mrs/Ms) indicate that coarse magnetic grains are mainly distributed in dark brown sediments (lower part of the sediment core samples) reflecting high Hcr/Hc and low Mrs/Ms ratios. These results are mainly caused by dissolution differences with core depth. From the plotting of the ratios of hyteresis parameters, it is indicated that magnetic minerals in cubic samples are in pseudo-single domain (PSD) state.

Sedimentary processes on the Storfjorden trough-mouth fan during last deglaciation phase: the role of subglacial meltwater plumes on continental margin sedimentation

NASA Astrophysics Data System (ADS)

Lucchi, Renata G.; Camerlenghi, Angelo; Colmenero-Hidalgo, Elena; Sierro, Francisco J.; Bárcena, Maria Angeles; Flores, José-Abel; Urgeles, Roger; Macrı, Patrizia; Sagnotti, Leonardo; Caburlotto, Andrea

2010-05-01

The continental margin of the Southern Storfjorden trough-mouth fan was investigated within the SVAIS project (BIO Hesperides cruise, August 2007) as a Spanish contribution to IPY Activity N. 367 (Neogene ice streams and sedimentary processes on high- latitude continental margins - NICE STREAMS). The objectives were to investigate the glacially-dominated late-Neogene-Quaternary sedimentary architecture of the NW Barents Sea continental margin and reconstruct its sedimentary system in response to natural climate change. The paleo-ice streams in Storfjorden had a small catchment area draining ice from the southern Spitsbergen and Bear Island. The short distance from the ice source to the calving front produced a short residence time of ice, and therefore a rapid response to climatic changes. Here ground truthing recovered the last few thousands years sedimentary sequence thought to represent last deglaciation phase. Detailed palaeostratigraphic investigations together with paleomagnetic and rock magnetic analyses and AMS dating define the constraints for high-resolution inter-core correlation and dating. Most of the cores contain at the base gravity-mass deposits including debris flows and over-consolidated glacigenic diamicton. Mass deposits are overlain by an oxidized interval originated at the release and sink of fresh, cold and oxygenated melt-waters at the inception of the deglaciation phase. On the upper slope the oxidized interval is overlain by several meters of finely-stratified sediments composed of sandy-silt layers cyclically recurring within finer-grained laminated silty-clay sediments. Textural and compositional analyses suggest preferential deposition by settling from meltwater sediment-laden plumes (plumites) occurred during deglaciation with coarser layers representing episodes of subglacial meltwater discharge (glacial hyperpycnal flows) accompanying the ice streams retreat. The laminated sequence is truncated at uppermost part by a more recent gravity-mass deposit that possibly removed part of the younger sequence. In the deeper part of the slope the plumites consist of crudely laminated, terrigenous and almost barren sediments. Here the sedimentary sequence is topped by intensively bioturbated, bioclasts-bearing silty-clays representing the most recent interglacial sedimentation. On the continental shelf, the upper sedimentary sequence contains dispersed cm-thick bivalve's shells suggesting an oxygenated and nutrient-rich environment (interglacial) overlaying an interval of terrigenous, barren sediments (deglaciation). Here the short core's length suggests the presence of stiffer/coarser sediments at the base that could not be sampled. The seismic stratigraphy indicates that the slope is formed by alternating debris flow deposits and layered sediments corresponding into our cores to the fast-deposited, low-density, terrigenous plumites. Bathymetric and seismic data revealed the presence of widespread submarine landslides restricted to the southernmost part of Storfjorden continental slope. Geotechnical investigation are in progress in order to understand if such layered deposits can act on the slope as a possible preferential weak horizon favoring sediment failure.

Forced Convection and Sedimentation Past a Flat Plate

NASA Technical Reports Server (NTRS)

Pelekasis, Nikolaos A.; Acrivos, Andreas

1995-01-01

The steady laminar flow of a well-mixed suspension of monodisperse solid spheres, convected steadily past a horizontal flat plate and sedimenting under the action of gravity, is examined. It is shown that, in the limit as Re approaches infinity and epsilon approaches 0, where Re is the bulk Reynolds number and epsilon is the ratio of the particle radius a to the characteristic length scale L, the analysis for determining the particle concentration profile has several aspects in common with that of obtaining the temperature profile in forced-convection heat transfer from a wall to a fluid stream moving at high Reynolds and Prandtl numbers. Specifically, it is found that the particle concentration remains uniform throughout the O(Re(exp -1/2)) thick Blasius boundary layer except for two O(epsilon(exp 2/3)) thin regions on either side of the plate, where the concentration profile becomes non-uniform owing to the presence of shear-induced particle diffusion which balances the particle flux due to convection and sedimentation. The system of equations within this concentration boundary layer admits a similarity solution near the leading edge of the plate, according to which the particle concentration along the top surface of the plate increases from its value in the free stream by an amount proportional to X(exp 5/6), with X measuring the distance along the plate, and decreases in a similar fashion along the underside. But, unlike the case of gravity settling on an inclined plate in the absence of a bulk flow at infinity considered earlier, here the concentration profile remains continuous everywhere. For values of X beyond the region near the leading edge, the particle concentration profile is obtained through the numerical solution of the relevant equations. It is found that, as predicted from the similarity solution, there exists a value of X at which the particle concentration along the top side of the plate attains its maximum value phi(sub m) and that, beyond this point, a stagnant sediment layer will form that grows steadily in time. This critical value of X is computed as a function of phi(sub s), the particle volume fraction in the free stream. In contrast, but again in conformity with the similarity solution, for values of X sufficiently far removed from the leading edge along the underside of the plate, a particle-free region is predicted to form adjacent to the plate. This model, with minor modifications, can be used to describe particle migration in other shear flows, as, for example, in the case of crossflow microfiltration.

Tunnel barrier schottky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, Rongming; Cao, Yu; Li, Zijian

2018-02-20

A diode includes: a semiconductor substrate; a cathode metal layer contacting a bottom of the substrate; a semiconductor drift layer on the substrate; a graded aluminum gallium nitride (AlGaN) semiconductor barrier layer on the drift layer and having a larger bandgap than the drift layer, the barrier layer having a top surface and a bottom surface between the drift layer and the top surface, the barrier layer having an increasing aluminum composition from the bottom surface to the top surface; and an anode metal layer directly contacting the top surface of the barrier layer.

Does fluid infiltration affect the motion of sediment grains? - A 3-D numerical modelling approach using SPH

NASA Astrophysics Data System (ADS)

Bartzke, Gerhard; Rogers, Benedict D.; Fourtakas, Georgios; Mokos, Athanasios; Canelas, Ricardo B.; Huhn, Katrin

2017-04-01

With experimental techniques it is difficult to measure flow characteristics, e.g. the velocity of pore water flow in sediments, at a sufficient resolution and in a non-intrusive way. As a result, the effect of fluid flow at the surface and in the interior of a sediment bed on particle motion is not yet fully understood. Numerical models may help to overcome these problems. In this study Smoothed Particle Hydrodynamics (SPH) was chosen since it is ideally suited to simulate flows in sediment beds, at a high temporal and spatial resolution. The solver chosen is DualSPHysics 4.0 (www.dual.sphysics.org), since this is validated for a range of flow conditions. For the present investigation a 3D numerical flow channel was generated with a length of 15.0 cm, a width of 0.5 cm and a height of 4.0 cm. The entire domain was flooded with 8 million fluid particles, while 400 mobile sediment particles were deposited under applied gravity (grain diameter D50=10 mm) to generate randomly packed beds. Periodic boundaries were applied to the sidewalls to mimic an endless flow. To drive the flow, an acceleration perpendicular to the bed was applied to the fluid, reaching a target value of 0.3 cm/s, simulating 12 seconds of real time. Comparison of the model results to the law of the wall showed that flow speeds decreased logarithmically from the top of the domain towards the surface of the beds, indicating a fully developed boundary layer. Analysis of the fluid surrounding the sediment particles revealed critical threshold velocities, subsequently resulting in the initiation of motion due to drag. Sediment flux measurements indicated that with increasing simulation time a larger quantity of sediment particles was transported at the direct vicinity of the bed, whereas the amount of transported particles along with flow speed values, within the pore spaces, decreased with depth. Moreover, sediment - sediment particle collisions at the sediment surface lead to the opening of new pore spaces. As a result, higher quantities of fluid particles infiltrated through the larger interstices between the sediment particles, which successively increased the potential for the initiation of motion of sediment particles located in the deeper horizons. This effect has been underestimated in prior studies and highlights the importance of sediment - sediment particle collision and fluid infiltration as an important characteristic that can eventually help to better understand the development of the shear layer but also various sediment morphological features.

Feasibility Report and Environmental Impact Statement for Navigation Improvements at Bayou La Batre, Alabama

DTIC Science & Technology

1988-09-12

an active openwater disposal site. The results of their analyses indicated that petroleum hydrocarbon residues were predominant within the top 200 cm...Island. At this site petroleum hydrocarbons , concentrations of up to 50 ppm, were encountered within the top 100 cm of sediment. Other sites within the...general area showed low levels of petroleum hydrocarbons in surficial sediments with natural terrestrial hydrocarbons being predominant. Sediment

Consequences of the river valley bottom transformation after extreme flood (on the example of the Niida River, Japan)

NASA Astrophysics Data System (ADS)

Botavin, D.; Golosov, V.; Konoplev, A.; Wakiyama, Y.

2018-01-01

Detailed study of different sections of floodplain was undertaken in the Niida River basin (Fukushima Prefecture) after an extreme flood event which occurred in the middle of September 2015. The upstream part of the basin is located in the area with very high level of radionuclide contamination after the accident at Fukushima Dai-ichi NPP. Field and GIS methods were used, including direct measurement of the depth of fresh sediment and its area, with soil descriptions for the typical floodplain sections, measurement of dose rates, interpretation of space images for a few time intervals (before and after flood event) with the following evaluation of spatial changes in deposition for different floodplain sections. In addition, results of quantitative assessment of sedimentation rates and soil radionuclide contamination were applied for understanding the effect of extreme flood on alluvial soils of the different sections. It was established that the maximum sedimentation rates (20-50 cm/event) occurred in the middle part of the lower reach of the Niida River and in some locations of the upper reaches. Dose rates had reduced considerably for all the areas with high sedimentation because the top soil layers with high radionuclide contamination were buried under fresh sediments produced mostly due to bank erosion and mass movements.

Mussel beds are biological power stations on intertidal flats

NASA Astrophysics Data System (ADS)

Engel, Friederike G.; Alegria, Javier; Andriana, Rosyta; Donadi, Serena; Gusmao, Joao B.; van Leeuwe, Maria A.; Matthiessen, Birte; Eriksson, Britas Klemens

2017-05-01

Intertidal flats are highly productive areas that support large numbers of invertebrates, fish, and birds. Benthic diatoms are essential for the function of tidal flats. They fuel the benthic food web by forming a thin photosynthesizing compartment in the top-layer of the sediment that stretches over the vast sediment flats during low tide. However, the abundance and function of the diatom film is not homogenously distributed. Recently, we have realized the importance of bivalve reefs for structuring intertidal ecosystems; by creating structures on the intertidal flats they provide habitat, reduce hydrodynamic stress and modify the surrounding sediment conditions, which promote the abundance of associated organisms. Accordingly, field studies show that high chlorophyll a concentration in the sediment co-vary with the presence of mussel beds. Here we present conclusive evidence by a manipulative experiment that mussels increase the local biomass of benthic microalgae; and relate this to increasing biomass of microalgae as well as productivity of the biofilm across a nearby mussel bed. Our results show that the ecosystem engineering properties of mussel beds transform them into hot spots for primary production on tidal flats, highlighting the importance of biological control of sedimentary systems.

Reconstructing Oceanographic Conditions From the Holocene to the Last Glacial Maximum in the Bay of Bengal

NASA Astrophysics Data System (ADS)

Miller, J.; Dekens, P. S.; Weber, M. E.; Spiess, V.; France-Lanord, C.

2015-12-01

The International Ocean Discovery Program (IODP) Expedition 354 drilled 7 sites in the Bay of Bengal, providing a unique opportunity to improve our understanding of the link between glacial cycles, tropical oceanographic changes, and monsoon strength. Deep-sea sediment cores of the Bengal Fan fluctuate between sand, hemipelagic and terrestrial sediment layers. All but one of the sites (U1454) contain a layer of calcareous clay in the uppermost part of the core that is late Pleistocene in age. During Expedition 354 site U1452C was sampled at high resolution (every 2cm) by a broad group of collaborators with the goal of reconstructing monsoon strength and oceanographic conditions using a variety of proxies. The top 480 cm of site U1452C (8ºN, 87ºE, 3671m water depth) contains primarily nannofossil rich calcareous clay. The relatively high abundance of foraminifera will allow us to generate a high resolution record of sea surface temperature (SST) and sea surface salinity (SSS) using standard foraminifera proxies. We will present oxygen isotopes (δ18O) and Mg/Ca data of mixed layer planktonic foraminifera from the top 70cm of the core, representing the Holocene to the last glacial maximum. δ18O of planktonic foraminifera records global ice volume and local SST and SSS, while Mg/Ca of foraminifera is a proxy for SST. The paired Mg/Ca and δ18O measurements on the same samples of foraminifera, together with published estimates with global ocean δ18O, can be used to reconstruct both SST and local δ18O of seawater, which is a function of the evaporation/precipitation balance. In future work, the local SSS and SST during the LGM will be paired with terrestrial and other oceanic proxies to increase our understanding of how global climate is connected to monsoon strength.

Identifying the Jaramillo Subchron in cave sediments using ESR

NASA Astrophysics Data System (ADS)

Pares, J. M.; Moreno, D.; Duval, M.

2017-12-01

The Jaramillo Subchron is represented by marine isotope stages 31 to 28, a period that embodies a fundamental shift in the Earth's climate known as the Early-Middle Pleistocene transition (EMPT). Also, this time interval is a critical period in human evolution and therefore identifying the Jaramillo provides an invaluable timeline. The correlation of magnetic chrons to the GPTS in sediments is typically hampered by the lack of a tie-point, as radiometric methods are rarely appropriate. In this study we combine Electron Spin Resonance (ESR) results from quartz grains, and paleomagnetism to identify the Jaramillo Subchron in cave sediments that include artifact-bearing layers. The ESR age estimate is basically derived from the determination of the equivalent dose, which is the laboratory estimate of the total dose absorbed by the sample since the ESR signal has been last reset to zero by sunlight exposure, and the dose rate, which is an estimation of the mean dose annually absorbed by the sample. The magnetostratigraphic study, based on more than 140 specimens over 20 meters-thick sedimentary sequence, results in three major reversals, which are interpreted from top to bottom as the Matuyama-Brunhes boundary and the Jaramillo Subchron. Both sediments and speleothems generally carry stable remanent magnetization directions mostly residing in magnetite, as supported by progressive alternating field (AF) demagnetization and rock magnetism. ESR dating on quartz grains from an 80 cm-thick stratigraphic layer that displays normal polarity gives an age of 0.84±0.12 Ma, consistent within the error with the current ages of the Jaramillo Subchron. Documenting the Jaramillo in fossiliferous sediments is important because it saw the EMPT and associated faunal turnover, as well as the expansion of hominins outside Africa. Also, this study highlights the potential of ESR dating on quartz grains from cave sediments to interpret magnetostratigraphic records.

Facies implications of Trichichnus and Chondrites in turbidites and hemipelagites, Marnoso-arenacea Formation (Miocene), northern Apennines, Italy

DOE Office of Scientific and Technical Information (OSTI.GOV)

McBride, E.F.; Picard, M.D.

Trichichnus, a thread-like burrow possibly the work of sipunculan worms, is widespread in Bouma E (turbidite claystone) and H (hemipelagic claystone) layers and some thin turbidite sandstone beds in basin-plain and outer fan-lobe deposits of the Marnoso-arenacea Formation. Trichichnus closely resembles that described elsewhere in chalk and marlstone, although the burrows are smaller (mean diameter=0.13 mm) and burrow curvature is tighter. Trichichnus fills are darker than the host claystone because of high organic content and disseminated pyrite. Any distinctive internal structure of the burrow wall or fill was destroyed by pyrite growth. Trichichnus is most abundant in Bouma E layers,more » where burrow spacing ranges from 0.4 to 50 cm and burrows extend to depths of 160 cm. The Trichichnus maker commonly burrowed vertically down through E and D layers (clay and silt) and then horizontally on top of C layers (sand). The burrows also vertically penetrate Bouma C sandstone layers up to 6 cm thick, but they are rare in beds thicker than 3 cm. They are less abundant or not well displayed in H layers where Chondrites predominates. Trichichnus overprints Chondrites. Following deposition of the Contessa megaturbidite, which exceeds 9 m in thickness, the sediment surface was repopulated chiefly by Trichichnus and Chondrites producers. Trichichnus extends 160 cm below the top of the Contessa, whereas Chondrites extend only to 64 cm. This suggests a greater tolerance of Trichichnus makers to low in situ oxygen levels. The near absence of laminations in the E division of the Contessa megabed may be the result of Trichichnus burrows that were not pyritized and which lack textural identity.« less

Visualization of soil structure and pore structure modifications by pioneering ground beetles (Cicindelidae) in surface sediments of an artificial catchment

NASA Astrophysics Data System (ADS)

Badorreck, Annika; Gerke, Horst H.; Weller, Ulrich; Vontobel, Peter

2010-05-01

An artificial catchment was constructed to study initial soil and ecosystem development. As a key process, the pore structure dynamics in the soil at the surface strongly influences erosion, infiltration, matter dynamics, and vegetation establishment. Little is known, however, about the first macropore formation in the very early stage. This presentation focuses on observations of soil pore geometry and its effect on water flow at the surface comparing samples from three sites in the catchment and in an adjacent "younger" site composed of comparable sediments. The surface soil was sampled in cylindrical plastic rings (10 cm³) down to 2 cm depth in three replicates each site and six where caves from pioneering ground-dwelling beetles Cicindelidae were found. The samples were scanned with micro-X-ray computed tomography (at UFZ-Halle, Germany) with a resolution of 0.084 mm. The infiltration dynamics were visualized with neutronradiography (at Paul-Scherer-Institute, Switzerland) on slab-type soil samples in 2D. The micro-tomographies exhibit formation of surface sealing whose thickness and intensity vary with silt and clay content. The CT images show several coarser- and finer-textured micro-layers at the sample surfaces that were formed as a consequence of repeated washing in of finer particles in underlying coarser sediment. In micro-depressions, the uppermost layers consist of sorted fine sand and silt due to wind erosion. Similar as for desert pavements, a vesicular pore structure developed in these sediments on top, but also scattered in fine sand- and silt-enriched micro-layers. The ground-dwelling activity of Cicindelidae beetles greatly modifies the soil structure through forming caves in the first centimetres of the soil. Older collapsed caves, which form isolated pores within mixed zones, were also found. The infiltration rates were severely affected both, by surface crusts and activity of ground-dwelling beetles. The observations demonstrate relatively high abiotic and biotic dynamics of soil pore structure in the soil surface even during the very early development stages. The structure formation has potentially great effects on changing runoff and infiltration by forming sealing layers or preferential flow paths.

A systematic technique for the sequential restoration of salt structures

NASA Astrophysics Data System (ADS)

Rowan, Mark G.

1993-12-01

A method is described for the sequential restoration of cross sections in areas of salt tectonics where deformation is confined to the salt and higher layers. The subsurface geometry evolves with time through the interaction of various processes: sedimentation, compaction, isostatic adjustment, thermal subsidence (if present), faulting, and salt withdrawal/ diapirism. The technique systematically calculates and removes the effects of each of these processes during specified time intervals defined by the interpreted horizons. It makes no assumptions about salt kinematics and generally results in the area of the salt layer changing through time. The method is described for restoration of extensional terranes, but it is also suitable for areas of contractional salt tectonics with only minor modifications. After converting an interpreted seismic profile to depth, the top layer is stripped off and the underlying section is decompacted according to standard porosity-depth functions. A deep baseline, unaffected by compaction or deformation, is used to restore any isostatic compensation or thermal subsidence. Isostasy is calculated according to the Airy model, and differential sedimentary loading across a section is shown to be approximately balanced by changes in salt thickness so that the load is evenly distributed. After these processes have been reversed, the resulting geometry and the seismic data are used to create the sea-floor template for structural restoration. Fault offsets are removed and the layers down to the top salt are restored to this template, while the base salt remains fixed. The resulting space between the restored top salt and the fixed base salt defines the restored salt geometry. In addition, the difference between the sea-floor template and a fixed sea level provides a measure of the change in water depth (ignoring eustatic changes in sea level). The technique is applied to an interpreted seismic profile from the eastern Green Canyon/Ewing Bank area of offshore Louisiana. The section is characterized by a variety of salt structures, including salt rollers, a diapiric massif, a remnant salt sheet, and a salt weld, which are shown to have derived from an originally continuous salt sheet which has been modified by sedimentary loading. Early loading created vertical basin growth that was accommodated primarily by salt withdrawal and associated diapiric rise through the process of downbuilding. Once the salt weld formed, continued sedimentation was accommodated by a lateral increase in basin size caused by down-dip extension on listric growth faults.

Latest Pannonian and Quaternary evolution at the transition between Eastern Alps and Pannonian Basin: new insights from geophysical, sedimentological and geochronological data

NASA Astrophysics Data System (ADS)

Zámolyi, A.; Salcher, B.; Draganits, E.; Exner, U.; Wagreich, M.; Gier, S.; Fiebig, M.; Lomax, J.; Surányi, G.; Diel, M.; Zámolyi, F.

2017-07-01

The transition zone between Eastern Alps and Pannonian Basin is a key area for the investigation of the interplay between regional uplift, local tectonic subsidence and depositional environment. Our study area, the western margin of the Little Hungarian Plain, is characterized by gentle hills, plateaus and depressions, of which several are filled by lakes—including one of Austria's largest and shallowest lakes, Lake Neusiedl. Geological investigation is hampered by the scarcity of outcrops, and thus direct observation of sedimentological or structural features is difficult. Despite a long research history in the area, a consistent landscape evolution model considering all relevant constraints is lacking so far. In this study, we apply multidisciplinary methods to decipher the complex tectonic and fluvial depositional evolution of the region. Local data from shallow-lake drilling and seismic investigation are combined with regional data from industrial seismics and core data to gain new insights into the latest Pannonian (Late Miocene) and Quaternary evolution. Shallow-lake seismic data show the erosionally truncated Pannonian sediments dipping and thickening toward southeast, toward the modern depocenter of the Little Hungarian Plain. Overlying Quaternary fluvial sediments show a very similar thickening trend except for the area on the plateau north of the lake indicating ongoing subsidence in major parts of the basin. Drill cores from locations along the lake seismic lines were analyzed concerning their age, mineralogy and heavy minerals and compared with outcrop samples from the surrounding plains and the plateau to derive indications on sediment provenance. A key observation is the apparent lack of a significant gravel layer on top of the tilted Pannonian sediments beneath Lake Neusiedl. Small-scale faults can be observed in the lake seismic sections along with key sedimentary features. Significant differences of the current elevation of the top Pannonian between the surrounding plains and the plateau indicate post-Pannonian normal faulting, which is a key process in shaping the present-day morphology of the region. Luminescence ages of samples from the Quaternary fluvial gravels on top of the Pannonian sediments are a significantly higher (>300 ka) compared to the gravels in the plain (102 ± 11 and 76 ± 8 ka), suggesting ongoing tectonic subsidence.

Lateral variation in crustal and mantle structure in Bay of Bengal based on surface wave data

NASA Astrophysics Data System (ADS)

Kumar, Amit; Mukhopadhyay, Sagarika; Kumar, Naresh; Baidya, P. R.

2018-01-01

Surface waves generated by earthquakes that occurred near Sumatra, Andaman-Nicobar Island chain and Sunda arc are used to estimate crustal and upper mantle S wave velocity structure of Bay of Bengal. Records of these seismic events at various stations located along the eastern coast of India and a few stations in the north eastern part of India are selected for such analysis. These stations lie within regional distance of the selected earthquakes. The selected events are shallow focused with magnitude greater than 5.5. Data of 65, 37, 36, 53 and 36 events recorded at Shillong, Bokaro, Visakhapatnam, Chennai and Trivandrum stations respectively are used for this purpose. The ray paths from the earthquake source to the recording stations cover different parts of the Bay of Bengal. Multiple Filtering Technique (MFT) is applied to compute the group velocities of surface waves from the available data. The dispersion curves thus obtained for this data set are within the period range of 15-120 s. Joint inversion of Rayleigh and Love wave group velocity is carried out to obtain the subsurface information in terms of variation of S wave velocity with depth. The estimated S wave velocity at a given depth and layer thickness can be considered to be an average value for the entire path covered by the corresponding ray paths. However, we observe variation in the value of S wave velocity and layer thickness from data recorded at different stations, indicating lateral variation in these two parameters. Thick deposition of sediments is observed along the paths followed by surface waves to Shillong and Bokaro stations. Sediment thickness keeps on decreasing as the surface wave paths move further south. Based on velocity variation the sedimentary layer is further divided in to three parts; on top lay unconsolidated sediment, underlain by consolidated sediment. Below this lies a layer which we consider as meta-sediments. The thickness and velocity of these layers decrease from north to south. The crustal material has higher velocity at the southern part compared to that at the northern part of Bay of Bengal indicating that it changes from more oceanic type in the southern part of the Bay to more continental type to its north. Both Moho and lithosphere - asthenosphere boundary (LAB) dips gently towards north. Thicknesses of both lithosphere and asthenosphere also increase in the same direction. The mantle structure shows complex variation from south to north indicating possible effect of repeated changes in type of tectonic activity in the Bay of Bengal.

Continuous and Episodic Modern Sediment Accumulation on Monterey Fan: Evidence from Ddt, 137Cs and Excess 210Pb

NASA Astrophysics Data System (ADS)

Gwiazda, R.; Paull, C. K.; Alexander, C. R.; Ussler, W.

2012-12-01

The mode and magnitude of fine-grained sediment accumulation on the Monterey Fan off the California central coast was investigated using pesticide concentrations and radioactive tracer profiles in sediment cores. DDT is a man-made pesticide that was used extensively in central California between 1945 and 1970. As such, its presence in marine sediments is a telltale sign of a modern sedimentation age. DDT and its metabolites, DDE and DDD, (collectively referred to as DDTr) were measured in fifty-five ~20cm-long sediment cores collected from the surface of the Monterey Fan up to 250 km to the south and 210 km to the west of the Monterey Canyon head, and in four transects across the Monterey Canyon channel at maximum water depths of 3160, 3380, 3580, and 3880 meters. Profiles of excess 210Pb (210Pbxs) and 137Cs were measured in 5 cores from the Fan to estimate recent sedimentation rates. Detectable levels of DDTr were observed in all but one of these cores, with DDTr concentrations characteristically highest at the surface and decreasing with depth. The area-normalized and depth-integrated DDTr content measured in all the cores in the Fan and in the deepest two channel transects was geographically fairly homogenous, with no statistical relationship between DDTr inventory and distance from the main channel crossing the Fan. The total sediment mass deposited on the Fan over the last 60 years, inferred from the total inventory of DDTr present in the area surveyed, is consistent with the amount of sediment delivered by the Salinas River over the same time period. 210Pbxs activities are fairly homogeneous within an uppermost layer of variable thickness (4.6-8cm) and decrease exponentially below it, but these exponential decreases are often interrupted by horizons with constant or increased 210Pbxs activity. Moreover, the coexistence of variable DDTr concentrations with homogeneous 210Pbxs activities in the top sediment indicates that the uniformity of 210Pbxs is not due primarily to bioturbation but rather the result of deposition of thick layers with constant 210Pbxs. These data indicate that fine-grained sedimentation on the Monterrey Fan appears to have a dual modality consisting of sustained slow accumulation at a modest rate during quiescent periods interrupted by episodes of rapid accumulation during discrete events. Median sedimentation rates during quiescent periods are 0.07 cm yr-1, but over the 110 year period of detectable 210Pbxs, which includes both slow continuous sedimentation and rapid accumulation events, the median overall sedimentation rate, calculated from the deepest detectable 210Pbxs samples, is 0.19 cm yr-1. On a per mass basis, sedimentation on the Fan has been equally divided between periods of continual slow accumulation and episodes of fast accumulation. The rapidly deposited layers on the Monterey Fan are inferred to result from the injection of fluvial sediments onto the Fan during episodic and exceptionally large floods of the Salinas River.

Tropism in azalea and lily flowers

NASA Astrophysics Data System (ADS)

Shimizu, M.; Tomita-Yokotani, K.; Nakamura, T.; Yamashita, M.

Tropic responses were examined in azalea Rhododendrom pulchrum and lily Lilium cv. 'Casablanca' flowers. Orientation of the flowers in these two species depicts several up/down characteristics, such as angle of the corolla opening, alignment or configuration of a specific petal at the top, plus direction in the curved tip of the pistil and stamen. Gravity was found to be the prime factor, with light as a secondary signal that determines gravitropism in the pistil of the azalea. Within the azalea, sedimented amyloplasts were observed throughout the cells along the inner layers below the epidermis. In lily flowers, no sedimented amyloplasts were found in style cells, and phototropic responses caused upward bending of the pistil. Responses of lily pistils to monochromatic light were consistent with the action spectrum for phototropism in the shoots of monocotyledonous plants. We discuss how these features may increase the fitness for pollination in these two species.

The Grain-size Patchiness of Braided Gravel-Bed Streams - example of the Urumqi River (northeast Tian Shan, China)

NASA Astrophysics Data System (ADS)

Guerit, L.; Barrier, L.; Narteau, C.; Métivier, F.; Liu, Y.; Lajeunesse, E.; Gayer, E.; Meunier, P.; Malverti, L.; Ye, B.

2014-02-01

In gravel-bed rivers, sediments are often sorted into patches of different grain-sizes, but in braided streams, the link between this sorting and the channel morpho-sedimentary elements is still unclear. In this study, the size of the bed sediment in the shallow braided gravel-bed Urumqi River is characterized by surface-count and volumetric sampling methods. Three morpho-sedimentary elements are identified in the active threads of the river: chutes at flow constrictions, which pass downstream to anabranches and bars at flow expansions. The surface and surface-layer grain-size distributions of these three elements show that they correspond to only two kinds of grain-size patches: (1) coarse-grained chutes, coarser than the bulk river bed, and (2) finer-grained anabranches and bars, consistent with the bulk river bed. In cross-section, the chute patches are composed of one coarse-grained top layer, which can be interpreted as a local armour layer overlying finer deposits. In contrast, the grain size of the bar-anabranch patches is finer and much more homogeneous in depth than the chute patches. Those patches, which are features of lateral and vertical sorting associated to the transport dynamics that build braided patterns, may be typical of active threads in shallow gravel-bed rivers and should be considered in future works on sorting processes and their geomorphologic and stratigraphic results.

Joint inversions of three types of electromagnetic data explicitly constrained by seismic observations: results from the central Okavango Delta, Botswana

NASA Astrophysics Data System (ADS)

Kalscheuer, Thomas; Blake, Sarah; Podgorski, Joel E.; Wagner, Frederic; Green, Alan G.; Maurer, Hansruedi; Jones, Alan G.; Muller, Mark; Ntibinyane, Ongkopotse; Tshoso, Gomotsang

2015-09-01

The Okavango Delta of northern Botswana is one of the world's largest inland deltas or megafans. To obtain information on the character of sediments and basement depths, audiomagnetotelluric (AMT), controlled-source audiomagnetotelluric (CSAMT) and central-loop transient electromagnetic (TEM) data were collected on the largest island within the delta. The data were inverted individually and jointly for 1-D models of electric resistivity. Distortion effects in the AMT and CSAMT data were accounted for by including galvanic distortion tensors as free parameters in the inversions. By employing Marquardt-Levenberg inversion, we found that a 3-layer model comprising a resistive layer overlying sequentially a conductive layer and a deeper resistive layer was sufficient to explain all of the electromagnetic data. However, the top of the basal resistive layer from electromagnetic-only inversions was much shallower than the well-determined basement depth observed in high-quality seismic reflection images and seismic refraction velocity tomograms. To resolve this discrepancy, we jointly inverted the electromagnetic data for 4-layer models by including seismic depths to an interface between sedimentary units and to basement as explicit a priori constraints. We have also estimated the interconnected porosities, clay contents and pore-fluid resistivities of the sedimentary units from their electrical resistivities and seismic P-wave velocities using appropriate petrophysical models. In the interpretation of our preferred model, a shallow ˜40 m thick freshwater sandy aquifer with 85-100 Ωm resistivity, 10-32 per cent interconnected porosity and <13 per cent clay content overlies a 105-115 m thick conductive sequence of clay and intercalated salt-water-saturated sands with 15-20 Ωm total resistivity, 1-27 per cent interconnected porosity and 15-60 per cent clay content. A third ˜60 m thick sandy layer with 40-50 Ωm resistivity, 10-33 per cent interconnected porosity and <15 per cent clay content is underlain by the basement with 3200-4000 Ωm total resistivity. According to an interpretation of helicopter TEM data that cover the entire Okavango Delta and borehole logs, the second and third layers may represent lacustrine sediments from Paleo Lake Makgadikgadi and a moderately resistive freshwater aquifer comprising sediments of the recently proposed Paleo Okavango Megafan, respectively.

Large-scale fabrication of vertically aligned ZnO nanowire arrays

DOEpatents

Wang, Zhong Lin; Hu, Youfan; Zhang, Yan; Xu, Chen; Zhu, Guang

2014-09-09

A generator includes a substrate, a first electrode layer, a dense plurality of vertically-aligned piezoelectric elongated nanostructures, an insulating layer and a second electrode layer. The substrate has a top surface and the first electrode layer is disposed on the top surface of the substrate. The dense plurality of vertically-aligned piezoelectric elongated nanostructures extends from the first electrode layer. Each of the nanostructures has a top end. The insulating layer is disposed on the top ends of the nanostructures. The second electrode layer is disposed on the non-conductive layer and is spaced apart from the nanostructures.

Equilibrium and kinetic modeling of contaminant immobilization by activated carbon amended to sediments in the field.

PubMed

Rakowska, Magdalena I; Kupryianchyk, Darya; Koelmans, Albert A; Grotenhuis, Tim; Rijnaarts, Huub H M

2014-12-15

Addition of activated carbons (AC) to polluted sediments and soils is an attractive remediation technique aiming at reducing pore water concentrations of hydrophobic organic contaminants (HOCs). In this study, we present (pseudo-)equilibrium as well as kinetic parameters for sorption of a series of PAHs and PCBs to powdered and granular activated carbons (AC) after three different sediment treatments: sediment mixed with powdered AC (PAC), sediment mixed with granular AC (GAC), and addition of GAC followed by 2 d mixing and subsequent removal ('sediment stripping'). Remediation efficiency was assessed by quantifying fluxes of PAHs towards SPME passive samplers inserted in the sediment top layer, which showed that the efficiency decreased in the order of PAC > GAC stripping > GAC addition. Sorption was very strong to PAC, with Log KAC (L/kg) values up to 10.5. Log KAC values for GAC ranged from 6.3-7.1 and 4.8-6.2 for PAHs and PCBs, respectively. Log KAC values for GAC in the stripped sediment were 7.4-8.6 and 5.8-7.7 for PAH and PCB. Apparent first order adsorption rate constants for GAC (kGAC) in the stripping scenario were calculated with a first-order kinetic model and ranged from 1.6 × 10(-2) (PHE) to 1.7 × 10(-5) d(-1) (InP). Sorption affinity parameters did not change within 9 months post treatment, confirming the longer term effectiveness of AC in field applications for PAC and GAC. Copyright © 2014. Published by Elsevier Ltd.

Sediment phosphate composition in relation to emergent macrophytes in the Doñana Marshes (SW Spain)

USGS Publications Warehouse

Reina, M.; Espinar, J.L.; Serrano, L.

2006-01-01

We have studied the effect of the presence of emergent macrophytes on the sediment phosphate composition of a eutrophic shallow marsh on the NE margin of Doñana (SW Spain). Top sediment and water samples were collected from both the open-water and the vegetated sites at three areas covered by different plant species: Scirpus maritimus, Juncus subulatus and Phragmites australis. The concentration of organic matter was significantly higher in the top sediment of sites covered by vegetation than in their adjacent open-water sites at the three vegetation areas. The P-fractional composition showed that the sediment was dominated by the inorganic P-fractions in all cases, reaching the highest concentration in the Ca-bound P-fraction (281–372 μg g−1 d.w.). The sum of all P-fractions was significantly higher in the top sediment of the sites covered by J. subulatus and S. maritimus than in their adjacent open-water sites, and so were the org-P fraction extracted by hot NaOH and the concentration of phytate within this fraction. Deposition of plant material on the top sediment of areas vegetated by J. subulatus and S. maritimus explains these differences. The P-fractional composition of the seeds from J. subulatus showed that they contained a large proportion of organic P-fractions, particularly of the fraction extracted by hot NaOH (1868 μg g−1 d.w., 85% of which was phytate). The presence of emergent macrophytes, therefore, influenced the distribution of P-fractions in the sediment depending on plant species. The P-bioavailability of shallow aquatic systems must be fully understood if wetlands are to be protected from further eutrophication.

Orbital SAR and Ground-Penetrating Radar for Mars: Complementary Tools in the Search for Water

NASA Technical Reports Server (NTRS)

Campbell, B. A.; Grant, J. A.

2000-01-01

The physical structure and compositional variability of the upper martian crust is poorly understood. Optical and infrared measurements probe at most the top few cm of the surface layer and indicate the presence of layered volcanics and sediments, but it is likely that permafrost, hydrothermal deposits, and transient liquid water pockets occur at depths of meters to kilometers within the crust. An orbital synthetic aperture radar (SAR) can provide constraints on surface roughness, the depth of fine-grained aeolian or volcanic deposits, and the presence of strongly absorbing near-surface deposits such as carbonates. This information is crucial to the successful landing and operation of any rover designed to search for subsurface water. A rover-based ground-penetrating radar (GPR) can reveal layering in the upper crust, the presence of erosional or other subsurface horizons, depth to a permafrost layer, and direct detection of near-surface transient liquid water. We detail here the radar design parameters likely to provide the best information for Mars, based on experience with SAR and GPR in analogous terrestrial or planetary environments.

Reconstruction of anthropogenic eutrophication in the region off the Changjiang Estuary and central Yellow Sea: From decades to centuries

NASA Astrophysics Data System (ADS)

Zhu, Zhuo-Yi; Wu, Ying; Zhang, Jing; Du, Jin-Zhou; Zhang, Guo-Sen

2014-01-01

Anthropogenic activities are known to induce estuarine and coastal eutrophication. However, the eutrophication history over a longer time scale (e.g., over hundreds of years) is often missing, and this perspective is important for an objective assessment of recent-decades anthropogenic activities. To reconstruct eutrophication history in this region, two sediment cores were taken, core E4 in the region off the Changjiang Estuary in the coast of East China Sea, and core E2 in the central Yellow Sea. High sedimentation rate (3.8 cm/yr) of core E4 enabled us to reconstruct a detailed anthropogenic eutrophication history for the past 70 years, while the history at least back to 1855 was further revealed via core E2. Sedimentary nitrogen isotopes (δ15N) in core E4 showed a gradually depleting trend from 5‰ (1930s) to 3.8‰ in the top, which is consistent with the increasing riverine nitrogen flux over the past few decades. A negative relationship was found between total sedimentary Chla (=preserved chlorophyll a+its degradation products) and δ15N (r2=0.68), suggesting the promotion of estuarine productivity by chemical fertilizer-N. Preserved diagnostic pigments ratio (peridinin/fucoxanthin) further suggests that after 1995, the influence of dinoflagellates has been increasing compared to diatoms. At a longer time scale (i.e., core E2), sedimentary δ15N also decreased from 5.1‰ (before 1855) to 4.4‰ (at top layer). As normalized fossil cyanobacterial pigment (zeaxanthin) showed a decreasing trend from before 1855 to the top of the core, we propose that the decreasing sedimentary δ15N after 1855 was not due to assimilation of atmospheric nitrogen, but due to excess nutrients input to the central Yellow Sea, which promoted primary production. This is further proved by preserved pheopigments, which continuously increased from 41.7 nmol g OC-1 (before 1855) to 251 nmol g OC-1 (at top layer) in core E2. Besides revealing the eutrophication history, big history events were also recorded, including the 1998 flood of the Changjiang River (core E4) and the shift of the Yellow River mouth in 1855 (core E2).

The Fulong coastal area in northeast Taiwan: Late Holocene sedimentary phases including destruction and aggradation

NASA Astrophysics Data System (ADS)

Boese, Margot; Luethgens, Christopher; Bauersachs, Marc

2014-05-01

Coastal areas are often subject to rapid morphological transformations owing to varying processes such as sea level changes, tectonic uplift, and geomorphological changes by catastrophic storm events, followed by phases of resilience. The study sites in northeast Taiwan at Fulong beach and adjacent areas, situated close to a nuclear power plant construction site, give evidence of an aggradational phase, a destructive phase, and resilience by a second aggradational phase. According to OSL data, a first aeolian accumulation started on top of marine and peri-marine/fluvial sediments at about 3 ka and lasted about 1500 years, interrupted by one palaeosoil. These data refer to an outcrop at a meander bluff at the southern bank of the Shuangsi river, not far from its present-day mouth. According to the morphological situation, this sand accumulation is only the remnant of a former greater dune system that has been eroded in its northern part. The former course of the Shuangsi and the location of its mouth are not known. The top of the outcrop is represented by two sand layers which are definitely younger than the lower sands as their deposition started about max. 630 years ago. The present-day dune system to the north of the river shows at least four dune ridges and the seaward aggradation is still continuing. The oldest dune ridge was sampled close to its top and dated to about 600 years ago (Dörschner et al. 2012). About 3 km upstream, a sedimentary sequence at the river bank has been studied, comprising a lower silty deposit with organic remnants and layered tree trunks at its top. This deposit is considered to be of marine origin, probably a peri-marine situation. This fine-grained sediment is covered by coarse fluvial gravels, indicating one or several catastrophic events in this morphological environment. Above the gravels, another fine-grained sediment related to flood events with low energy has been found. Radiocarbon analyses of organic material in both fine-grained sediments yielded ages supporting the results from the coastline The sedimentological records and the geomorphological situation give evidence of a short time period with one or several destructive events that destroyed an older dune system at the coast and may be linked to the deposition of the coarse gravels in the river profile. If the existing age estimates are interpreted in this sense, the time window for such an event is about 660 to 600 years ago. The coast afterwards entered a phase of resilience: the new dune ridge system came into existence, and since then the process of a prograding coastline has been active and was supported by an uplift of about 2mm/a, which was calculated on the base of marine deposits found in two outcrops. Dörschner, N., Reimann, T., Wenske, D., Lüthgens, C., Tsukamoto, S., Frechen, M., Böse, M., 2012: Reconstruction of the Holocene coastal development at Fulong Beach in northeastern Taiwan using optically stimulated luminescence (OSL) dating. Quaternary International, 263, 3-13.

Diversity and spatial distribution of prokaryotic communities along a sediment vertical profile of a deep-sea mud volcano.

PubMed

Pachiadaki, Maria G; Kallionaki, Argyri; Dählmann, Anke; De Lange, Gert J; Kormas, Konstantinos Ar

2011-10-01

We investigated the top 30-cm sediment prokaryotic community structure in 5-cm spatial resolution, at an active site of the Amsterdam mud volcano, East Mediterranean Sea, based on the 16S rRNA gene diversity. A total of 339 and 526 sequences were retrieved, corresponding to 25 and 213 unique (≥98% similarity) phylotypes of Archaea and Bacteria, respectively, in all depths. The Shannon-Wiener diversity index H was higher for Bacteria (1.92-4.03) than for Archaea (0.99-1.91) and varied differently between the two groups. Archaea were dominated by anaerobic methanotrophs ANME-1, -2 and -3 groups and were related to phylotypes involved in anaerobic oxidation of methane from similar habitats. The much more complex Bacteria community consisted of 20 phylogenetic groups at the phylum/candidate division level. Proteobacteria, in particular δ-Proteobacteria, was the dominant group. In most sediment layers, the dominant phylotypes of both the Archaea and Bacteria communities were found in neighbouring layers, suggesting some overlap in species richness. The similarity of certain prokaryotic communities was also depicted by using four different similarity indices. The direct comparison of the retrieved phylotypes with those from the Kazan mud volcano of the same field revealed that 40.0% of the Archaea and 16.9% of the Bacteria phylotypes are common between the two systems. The majority of these phylotypes are closely related to phylotypes originating from other mud volcanoes, implying a degree of endemicity in these systems.

Accumulation, Release, and Solubility of Arsenic, Molybdenum, and Vanadium in Wetland Sediments

USGS Publications Warehouse

Fox, P.M.; Doner, H.E.

2003-01-01

This study was undertaken to determine the fate of As, Mo, and V (trace elements, TEs) in the sediments of a constructed wetland in use for the remediation of potentially toxic trace element-contaminated agricultural drainwater. After three years of wetland operation, sediment cores were collected to determine changes in TE concentrations as a function of depth and the effects of varying water column depth. All TE concentrations were highest in the top 2 to 4 cm and decreased with depth. Molybdenum accumulated in the wetland sediments, up to levels of 32.5 ?? 4.6, 30.2 ?? 8.9, and 59.3 ?? 26.1 mg kg-1 in the top 1 cm of sediment at water depths of 15, 30, and 60 cm, respectively. In the top 2 cm of sediment, As accumulated (28.2 ?? 3.0 mg kg-1) only at the 60-cm water depth. Below 2 cm, as much as 10 mg kg-1 of As was lost from the sediment at all water depths. In most cases, V concentrations decreased in the sediment. In this wetland system, the lowest redox potentials were found near the sediment surface and increased with depth. Thus, in general As, Mo, and V concentrations in the sediment were highest under more reducing conditions and lowest under more oxidizing conditions. Most of the accumulated Mo (73%) became water soluble on drying of samples. This has important implications for systems undergoing changes in redox status; for instance, if these wetland sediments are dried, potentially large amounts of Mo may be solubilized.

Heavy metal distributions in Peru Basin surface sediments in relation to historic, present and disturbed redox environments

NASA Astrophysics Data System (ADS)

Koschinsky, Andrea

Heavy metal distributions in deep-sea surface sediments and pore water profiles from five areas in the Peru Basin were investigated with respect to the redox environment and diagenetic processes in these areas. The 10-20-cm-thick Mn oxide-rich and minor metal-rich top layer is underlain by an increase in dissolved Mn and Ni concentrations resulting from the reduction of the MnO 2 phase below the oxic zone. The mobilised associated metals like Co, Zn and Cu are partly immobilised by sorption on clay, organic or Fe compounds in the post-oxic environment. Enrichment of dissolved Cu, Zn, Ni, Co, Pb, Cd, Fe and V within the upper 1-5 cm of the oxic zone can be attributed to the degradation of organic matter. In a core from one area at around 22-25 cm depth, striking enrichments of these metals in dissolved and solid forms were observed. Offset distributions between oxygen penetration and Mn reduction and the thickness of the Mn oxide-rich layer indicate fluctuations of the Mn redox boundary on a short-term time scale. Within the objectives of the German ATESEPP research programme, the effect of an industrial impact such as manganese nodule mining on the heavy metal cycle in the surface sediment was considered. If the oxic surface were to be removed or disturbed, oxygen would penetrate deep into the formerly suboxic sediment and precipitate Mn 2+ and metals like Ni and Co which are preferably scavenged by MnO 2. The solid enrichments of Cd, V, and other metals formed in post-oxic environments would move downward with the new redox boundary until a new equilibrium between oxygen diffusion and consumption is reached.

Development of a novel multi-functional active membrane capping barrier for the remediation of nitrobenzene-contaminated sediment.

PubMed

Wang, Qing; Li, Yi; Wang, Chao; Wu, Yue; Wang, Peifang

2014-07-15

A novel bio-reactive capping barrier composed of polysulfone/granular activated carbon (PS/GAC) hybrid membranes immobilized with microorganism was developed for the remediation of nitrobenzene in sediments. The SEM observation demonstrated that all the membranes had a dense top layer and a porous sublayer, this structure can block the transfer of nitrobenzene from sediment to the water and enhance nitrobenzene degradation. Adsorption behaviors of nitrobenzene on membranes showed that the membrane impregnated with GAC had better performance than the pure PS membrane. The values of Kads increased from 4.64 (without GAC) to 6.19 (1:2 GAC). 20mg/L nitrobenzene can be completely degraded by Pseudomonas putida immobilized on membranes. The biodegradation rate of activated carbon-filled membrane system was little higher than that of pure PS membrane system. For remediation experiments, only about 21.7, 28.3 and 43.9% of nitrobenzene in the sediment was removed by the end of the experiments for PS/GAC membrane, sand-alone and sand amended with activated carbon capping systems, respectively. While for PS/GAC+microorganisms capping system, more than 70% of nitrobenzene loss was observed. This demonstrated that nitrobenzene can be effectively removed from contaminated sediments by microbial degradation in the bio-reactive capping system. Copyright © 2014 Elsevier B.V. All rights reserved.

Hadal disturbance and radionuclide profiles at the deepest Japan Trench, northeastern Japan

NASA Astrophysics Data System (ADS)

Oguri, Kazumasa; Kawamura, Kiichiro; Sakaguchi, Arito; Toyofuku, Takashi; Kasaya, Takafumi; Murayama, Masafumi; Glud, Ronnie; Fujikura, Katsunori; Kitazato, Hiroshi

2013-04-01

Four months after the 2011 Tohoku-Oki earthquake, we carried out a video survey and collected sediment core collection from the hadal region (~7,600 m water depth) of the Japan Trench using an autonomous instrument. Fine material remained suspended at ~50 m above the seabed presumably induced by turbidities released during the central earthquake and the following aftershocks. Elevated levels of Cs-137 (T1/2=30 y) and excess Pb-210 (T1/2=22.3 y) concentrations suggested that 30 cm thick sediment layer had accumulated at the trench base (7,553 m) after the mainshock. However, no Cs-134 (T1/2=2 y) fallout from the Fukushima Dai-ichi nuclear disaster was detected. In contract, inspection of a nearby sediment site (7,261 m) 4.9 km away from the central trench site revealed fewer disturbances as reflected by a recent deposition of only 4 cm sediment, but here we encountered recent Cs-134 fallouts from the top 0-1 cm depth. We propose that the apparent lack of Cs-134 in the central trench is coursed by settlement of turbidites containing Cs-137 from past atmospheric fallout and higher excess Pb-210. The fast transport of the Cs-134 to the hadal slope sediment is presumably induced by enhanced scavenging and the vertical transport associated to an intensified diatom blooming occurring just at the time of the Fukushima disaster.

Sediment resuspension and bed armoring during high bottom stress events on the northern California inner continental shelf: measurements and predictions

NASA Astrophysics Data System (ADS)

Wiberg, Patricia L.; Drake, David E.; Cacchione, David A.

1994-08-01

Geoprobe bottom tripods were deployed during the winter of 1990-1991 on the northern California inner continental shelf as part of the STRESS field experiment. Transmissometer measurements of light beam attenuation were made at two levels and current velocity was measured at four levels in the bottom 1.2 m of water. Intervals of high measured bottom wave velocity were generally correlated with times of both high attenuation and high attenuation gradient in the bottom meter of the water column. Measured time series of light attenuation and attenuation gradient are compared to values computed using a modified version of the SMITH [(1977) The sea, Vol. 6, Wiley-Interscience, New York, pp. 539-577] steady wave-current bottom-boundary-layer model. Size-dependent transmissometer calibrations, which show significantly enhanced attenuation with decreasing grain size, are used to convert calculated suspended sediment concentration to light attenuation. The finest fractions of the bed, which are the most easily suspended and attenuate the most light, dominate the computed attenuation signal although they comprise only about 5-7% of the bed sediment. The calculations indicate that adjusting the value of the coefficient γ 0 in the expression for near-bed sediment concentration cannot in itself give both the correct magnitudes of light attenuation and attenuation gradient. To supply the volumes of fine sediment computed to be in suspension during peak events, even with values of γ 0 as low as 5 × 10 -5, requires suspension of particles from unreasonably large depths in the bed. A limit on the depth of sediment availability is proposed as a correction to suspended sediment calculations. With such a limit, reasonable attenuation values are computed with γ 0 ≈ 0.002. The effects of limiting availability and employing a higher γ 0 are to reduce the volume of the finest sediment in suspension and to increase the suspended volumes of the coarser fractions. As a consequence, the average size and settling velocity of suspended sediment increases as bottom shear stress increases, with accompanying increases in near-bed concentration gradients. Higher concentration gradients produce larger stratification effects, particularly near the top of the wave boundary layer at times when wave shear velocities are high and current shear velocities are low. These are the conditions under which maximum attenuation gradients are observed.

Sediment resuspension and bed armoring during high bottom stress events on the northern California inner continental shelf: measurements and predictions

USGS Publications Warehouse

Wiberg, P.L.; Drake, D.E.; Cacchione, D.A.

1994-01-01

Geoprobe bottom tripods were deployed during the winter of 1990-1991 on the northern California inner continental shelf as part of the STRESS field experiment. Transmissometer measurements of light beam attenuation were made at two levels and current velocity was measured at four levels in the bottom 1.2 m of water. Intervals of high measured bottom wave velocity were generally correlated with times of both high attenuation and high attenuation gradient in the bottom meter of the water column. Measured time series of light attenuation and attenuation gradient are compared to values computed using a modified version of the Smith [(1977) The sea, Vol. 6, Wiley-Interscience, New York, pp. 539-577] steady wave-current bottom-boundary-layer model. Size-dependent transmissometer calibrations, which show significantly enhanced attenuation with decreasing grain size, are used to convert calculated suspended sediment concentration to light attenuation. The finest fractions of the bed, which are the most easily suspended and attenuate the most light, dominate the computed attenuation signal although they comprise only about 5-7% of the bed sediment. The calculations indicate that adjusting the value of the coefficient ??0 in the expression for near-bed sediment concentration cannot in itself give both the correct magnitudes of light attenuation and attenuation gradient. To supply the volumes of fine sediment computed to be in suspension during peak events, even with values of ??0 as low as 5 ?? 10-5, requires suspension of particles from unreasonably large depths in the bed. A limit on the depth of sediment availability is proposed as a correction to suspended sediment calculations. With such a limit, reasonable attenuation values are computed with ??0 ??? 0.002. The effects of limiting availability and employing a higher ??0 are to reduce the volume of the finest sediment in suspension and to increase the suspended volumes of the coarser fractions. As a consequence, the average size and settling velocity of suspended sediment increases as bottom shear stress increases, with accompanying increases in near-bed concentration gradients. Higher concentration gradients produce larger stratification effects, particularly near the top of the wave boundary layer at times when wave shear velocities are high and current shear velocities are low. These are the conditions under which maximum attenuation gradients are observed. ?? 1994.

Trace metal in sediment from a deep-sea floor of Makassar Strait

NASA Astrophysics Data System (ADS)

Budianto, F.; Lestari

2018-02-01

Makassar Strait is located in the entrance of Indonesian Through Flow (ITF). However, the geochemistry of metals in sediment within Makassar Strait remains unexplored. The aim of this study was to measure the concentration of metals in sediment and to assess the sediment quality based on those metals concentrations. The sediment was collected from 632-4730 m in depth using giant piston corer on R/V Baruna Jaya VIII in December 2014. In each observation point, three layers of sediment were sub-sampled from the core i.e. surface layer (0-5 cm), middle layer (45-55 cm) and bottom layer. The metals were analyzed using acid digestion procedure followed by Atomic Absorption Spectrophotometer. The result indicated that the metal has spatially insignificant differences in sediment and the increase of metal concentration by depth was noticed. The Enrichment factor presented as no enrichment to minor enrichment of metal in sediment.

Evaluation of surficial sediment toxicity and sediment physico-chemical characteristics of representative sites in the Lagoon of Venice (Italy)

NASA Astrophysics Data System (ADS)

Losso, C.; Arizzi Novelli, A.; Picone, M.; Marchetto, D.; Pessa, G.; Molinaroli, E.; Ghetti, P. F.; Volpi Ghirardini, A.

2004-11-01

Toxic hazard in sites with varying types and levels of contamination in the Lagoon of Venice was estimated by means of toxicity bioassays based on the early life-stages of the autochthonous sea urchin Paracentrotus lividus. Elutriate was chosen as the test matrix, due to its ability to highlight potential toxic effects towards sensitive biological components of the water column caused by sediment resuspension phenomena affecting the Lagoon. Surficial sediments (core-top 5 cm deep), directly influenced by resuspension/redeposition processes, and core sediments (core 20 cm deep), recording time-mediated contamination, were sampled in some sites located in the lagoonal area most greatly influenced by anthropogenic activities. Particle size, organic matter and water content were also analysed. In two sites, the results of physical parameters showed that the core-top sediments were coarser than the 20-cm core sediments. Sperm cell toxicity test results showed the negligible acute toxicity of elutriates from all investigated sites. The embryo toxicity test demonstrated a short-term chronic toxicity gradient for elutriates from the 20-cm core sediments, in general agreement both with the expected contamination gradient and with results of the Microtox® solid-phase test. Elutriates of the core-top 5-cm sediments revealed a totally inverted gradient, in comparison with that for the 20-cm core sediments, and the presence of a "hot spot" of contamination in the site chosen as a possible reference. Investigations on ammonia and sulphides as possible confounding factors excluded their contribution to this "hot spot". Integrated physico-chemical and toxicity results on sediments at various depths demonstrated the presence of disturbed sediments in the central basin of the Lagoon of Venice.

Part 2: Sedimentary geology of the Valles, Marineris, Mars and Antarctic dry valley lakes

NASA Technical Reports Server (NTRS)

Nedell, Susan S.

1987-01-01

Detailed mapping of the layered deposits in the Valles Marineris, Mars from high-resolution Viking orbiter images revealed that they from plateaus of rhythmically layered material whose bases are in the lowest elevations of the canyon floors, and whose tops are within a few hundred meters in elevation of the surrounding plateaus. Four hypotheses for the origin of the layered deposits were considered: that they are eolian deposits; that they are remnants of the same material as the canyon walls; that they are explosive volcanic deposits; or that they were deposited in standing bodies of water. There are serious morphologic objections to each of the first three. The deposition of the layered deposits in standing bodies of water best explains their lateral continuity, horizontality, great thickness, rhythmic nature, and stratigraphic relationships with other units within the canyons. The Martian climatic history indicated that any ancient lakes were ice covered. Two methods for transporting sediment through a cover of ice on a martian lake appear to be feasible. Based on the presently available data, along with the theoretical calculations presented, it appears most likely that the layered deposits in the Valles Marineris were laid down in standing bodies of water.

A century long sedimentary record of anthropogenic lead (Pb), Pb isotopes and other trace metals in Singapore.

PubMed

Chen, Mengli; Boyle, Edward A; Switzer, Adam D; Gouramanis, Chris

2016-06-01

Reconstructing the history of metal deposition in Singapore lake sediments contributes to understanding the anthropogenic and natural metal deposition in the data-sparse Southeast Asia. To this end, we present a sedimentary record of Pb, Pb isotopes and eleven other metals (Ag, As, Ba, Cd, Co, Cr, Cu, Ni, Tl, U and Zn) from a well-dated sediment core collected near the depocenter of MacRitchie Reservoir in central Singapore. Before the 1900s, the sedimentary Pb concentration was less than 2 mg/kg for both soil and sediment, with a corresponding (206)Pb/(207)Pb of ∼1.20. The Pb concentration increased to 55 mg/kg in the 1990s, and correspondingly the (206)Pb/(207)Pb decreased to less than 1.14. The (206)Pb/(207)Pb in the core top sediment is concordant with the (206)Pb/(207)Pb signal of aerosols in Singapore and other Southeast Asian cities, suggesting that Pb in the reservoir sediment was mainly from atmospheric deposition. Using the Pb concentration in the topmost layer of sediment, the estimated atmospheric Pb flux in Singapore today is ∼1.6 × 10(-2) g/m(2) yr. The concentrations of eleven other metals preserved in the sediment were also determined. A principal component analysis showed that most of the metals exhibit an increasing trend towards 1990s with a local concentration peak in the mid-20(th) century. Copyright © 2016. Published by Elsevier Ltd.

An assessment of butyltins and metals in sediment cores from the St. Thomas East End Reserves, USVI.

PubMed

Hartwell, S Ian; Apeti, Dennis A; Mason, Andrew L; Pait, Anthony S

2016-11-01

Tributyltin (TBT) concentrations near a marina complex in Benner Bay on St. Thomas, US Virgin Islands, were elevated relative to other areas in a larger study of the southeastern shore of the island. At the request of the USVI Coastal Zone Management Program, sediment cores and surface sediment samples were collected to better define the extent and history of TBT deposition in the vicinity of Benner Bay. The sediment cores were sectioned into 2-cm intervals and dated with 210 Pb and 137 Cs. The core sections and the surface samples were analyzed for butyltins and 16 elements. Deposition rates varied from 0.07-5.0 mm/year, and were highest in the marina complex. Core ages ranged from 54 to 200 years. The bottoms of the cores contained shell hash, but the top layers all consisted of much finer material. Surface concentrations of TBT exceeded 2000 ng Sn/g (dry weight) at two locations. At a depth of 8 cm TBT exceeded 8800 ng Sn/g in the marina complex sediment. Based on the ratio of tributyltin to total butyltins, it appears that the marina sediments are the source of contamination of the surrounding area. There is evidence that vessels from neighboring islands may also be a source of fresh TBT. Copper concentrations increase over time up to the present. Gradients of virtually all metals and metalloids extended away from the marina complex. NOAA sediment quality guidelines were exceeded for As, Pb, Cu, Zn, and Hg.

Pleistocene ice-rich yedoma in Interior Alaska

NASA Astrophysics Data System (ADS)

Kanevskiy, M. Z.; Shur, Y.; Jorgenson, T. T.; Sturm, M.; Bjella, K.; Bray, M.; Harden, J. W.; Dillon, M.; Fortier, D.; O'Donnell, J.

2011-12-01

Yedoma, or the ice-rich syngenetic permafrost with large ice wedges, widely occurs in parts of Alaska that were unglaciated during the last glaciation including Interior Alaska, Foothills of Brooks Range and Seward Peninsula. A thick layer of syngenetic permafrost was formed by simultaneous accumulation of silt and upward permafrost aggradation. Until recently, yedoma has been studied mainly in Russia. In Interior Alaska, we have studied yedoma at several field sites (Erickson Creek area, Boot Lake area, and several sites around Fairbanks, including well-known CRREL Permafrost tunnel). All these locations are characterized by thick sequences of ice-rich silt with large ice wedges up to 30 m deep. Our study in the CRREL Permafrost tunnel and surrounding area revealed a yedoma section up to 18 m thick, whose formation began about 40,000 yr BP. The volume of wedge-ice (about 10-15%) is not very big in comparison with other yedoma sites (typically more than 30%), but soils between ice wedges are extremely ice-rich - an average value of gravimetric moisture content of undisturbed yedoma silt with micro-cryostructures is about 130%. Numerous bodies of thermokarst-cave ice were detected in the tunnel. Geotechnical investigations along the Dalton Highway near Livengood (Erickson Creek area) provided opportunities for studies of yedoma cores from deep boreholes. The radiocarbon age of sediments varies from 20,000 to 45,000 yr BP. Most of soils in the area are extremely ice-rich. Thickness of ice-rich silt varies from 10 m to more than 26 m, and volume of wedge-ice reaches 35-45%. Soil between ice wedges has mainly micro-cryostructures and average gravimetric moisture content from 80% to 100%. Our studies have shown that the top part of yedoma in many locations was affected by deep thawing during the Holocene, which resulted in formation of the layer of thawed and refrozen soils up to 6 m thick on top of yedoma deposits. Thawing of the upper permafrost could be related to climate changes during Holocene or to wildfires, or both. The ice-poor layer of thawed and refrozen sediments (gravimetric moisture content usually does not exceed 40%) was encountered in many boreholes below the thin ice-rich intermediate layer (gravimetric moisture content usually exceeds 100%). These two layers separate ice wedges from the active layer and protect them from further thawing. Such structure of the upper permafrost at different yedoma sites of Interior Alaska can explain a relatively rare occurrence of surface features related to yedoma degradation such as thermokarst mounds and erosional gullies developed along ice wedges.

Holocene Paleolimnological Records from Thule, Northwestern Greenland

NASA Astrophysics Data System (ADS)

Corbett, L.; Osterberg, E. C.; Kelly, M. A.; Axford, Y.

2012-12-01

Assessing Holocene climatic and environmental variability around the margin of the Greenland Ice Sheet provides important information against which to compare ice sheet margin fluctuations. Here, we report preliminary results from ongoing research in northwestern Greenland. We present records of physical properties of lake sediments and use these to make inferences about the evolution of the lake and its surroundings over the latter half of the Holocene. We collected two sediment cores, 90 and 72 cm in length, from a small (surface area ~0.3 km2), shallow (maximum depth ~4.5 m) lake at 76°33'40''N 68°26'31''W near Thule Air Base in July 2012. The length of the cores was limited by the length of the core barrel and does not reflect the total thickness of sediment in the lake. The lake is situated within the glacial limit and likely formed subsequent to deglaciation of the region during early Holocene time. No glaciers exist within the lake's catchment today; the primary modern source of sediment is a perennial inflow from the west. We developed a preliminary depth-age model using radiocarbon ages of terrestrial organic macrofossils. Thus far, we have analyzed the sediments for magnetic susceptibility and loss-on-ignition. A radiocarbon age of 6069 ± 90 cal yr BP at the base of the core indicates that the sediments preserve a continuous record of middle to late Holocene conditions. The top of both cores consists of a thick (~12 cm) layer of dark gray unlaminated sediments, while the rest of the material in both cores is lighter brown to olive, finely laminated sediment. The upper layer is characterized by low water content (<25%), low loss-on-ignition (<5%), and high magnetic susceptibility (~150-250 x10-6). Conversely, the laminated sediments beneath have higher water content (~40-50%), higher loss-on-ignition (~5-10%), and much lower magnetic susceptibility (<50 x10-6). We hypothesize that the upper, less organic unit may represent a single event in the lake's recent history. We are refining the depth-age model with more radiocarbon ages, measuring grain size and carbon to nitrogen ratios of the sediments, and evaluating possible linkages between the sediment physical properties and precipitation as recorded by annual accumulation in ice cores in northwestern Greenland and Arctic Canada. This project will provide a foundation for future work in Thule investigating Holocene fluctuations of local ice cap and ice sheet margin positions.

Top down arsenic uncertainty measurement in water and sediments from Guarapiranga dam (Brazil)

NASA Astrophysics Data System (ADS)

Faustino, M. G.; Lange, C. N.; Monteiro, L. R.; Furusawa, H. A.; Marques, J. R.; Stellato, T. B.; Soares, S. M. V.; da Silva, T. B. S. C.; da Silva, D. B.; Cotrim, M. E. B.; Pires, M. A. F.

2018-03-01

Total arsenic measurements assessment regarding legal threshold demands more than average and standard deviation approach. In this way, analytical measurement uncertainty evaluation was conducted in order to comply with legal requirements and to allow the balance of arsenic in both water and sediment compartments. A top-down approach for measurement uncertainties was applied to evaluate arsenic concentrations in water and sediments from Guarapiranga dam (São Paulo, Brazil). Laboratory quality control and arsenic interlaboratory tests data were used in this approach to estimate the uncertainties associated with the methodology.

230Th in the Eastern Equatorial Pacific Panama Basin

NASA Astrophysics Data System (ADS)

Singh, A. K.; Marcantonio, F.; Lyle, M.

2008-12-01

In the Panama Basin, higher glacial sediment mass accumulation rates (MARs), determined using oxygen isotope stratigraphy, have been suggested to be due to high surface water primary productivity [1]. More recently, however, the 230Th normalization method suggests that higher glacial sediment fluxes are due to sediment focusing by deep-ocean currents (e.g., [2]). Moreover, the 230Th inventory suggests that lateral advection of marine sediment in the Panama Basin is 2-4 times greater than the vertical flux, provided that the sediment is unfractionated by lateral transport. Differentiating between these two models of MARs is crucial to our understanding of the response of sedimentation to changes in climate, and how sediments record paleoceanographic information. Assuming that the 230Th model is correct, downslope transport of sediment from the top of the Carnegie ridge (an aseismic ridge that forms the southern boundary of the Panama Basin) may be the source of extra 230Th [2]. Previous geophysical studies also suggest that sediment focusing is a common phenomenon in the Panama Basin [3]. Here, we test the sediment redistribution hypothesis by measuring 230Th in cores located near the tops of the Carnegie ridge and other ridges that bound the Panama Basin (e.g., Cocos). If ridge tops are the source of sediment to the basin, then we expect the 230Th systematics to indicate focusing factors that are less than 1 there. An analysis of the mass balance of 230Th within the Panama Basin will be presented. [1] Lyle et al. 2002, Paleoceanography 17(2), 1013. [2] Kienast et al. 2007, Paleoceanography 22, 2213[3] Lonsdale and Malfait, 1974, Geol. Soc. Am. Bull., 85, 1697-1712

Methods to induce perpendicular magnetic anisotropy in full-Heusler Co2FeSi thin layers in a magnetic tunnel junction structure

NASA Astrophysics Data System (ADS)

Shinohara, Koki; Suzuki, Takahiro; Takamura, Yota; Nakagawa, Shigeki

2018-05-01

In this study, to obtain perpendicular magnetic tunnel junctions (p-MTJs) using half-metallic ferromagnets (HMFs), several methods were developed to induce perpendicular magnetic anisotropy (PMA) in full-Heusler Co2FeSi (CFS) alloy thin layers in an MTJ multilayer composed of a layered CFS/MgO/CFS structure. Oxygen exposure at 2.0 Pa for 10 min after deposition of the bottom CFS layer was effective for obtaining PMA in the CFS layer. One of the reasons for the PMA is the formation of nearly ideal CFS/MgO interfaces due to oxygen exposure before the deposition of the MgO layer. The annealing process was effective for obtaining PMA in the top CFS layer capped with a Pd layer. PMA was clearly observed in the top CFS layer of a Cr(40 nm)/Pd(50 nm)/bottom CFS(0.6 nm)/MgO(2.0 nm)/top CFS(0.6 nm)/ Pd(10 nm) multilayer, where the top CFS and Pd thin films were deposited at RT and subsequently annealed at 300°C. In addition to the continuous layer growth of the films, the crystalline orientation alignment at the top CFS/Pd interface probably attributes to the origin of PMA at the top CFS layer.

Earth Observations taken by the Expedition 15 Crew

NASA Image and Video Library

2007-09-12

ISS015-E-28002 (12 Sept. 2007) --- A section of Dinosaur National Monument along the Yampa River in Colorado, which straddles the Colorado/Utah border, is featured in this image photographed by an Expedition 15 crewmember on the International Space Station. Dinosaur National Monument is perhaps best known for the abundant fossils found in the approximately 145 Ma (mega-annum, or millions of years old) Morrison Formation exposed in valleys and low ridges, according to scientists. The fossil assemblage is a unique record of terrestrial life of the period (dinosaurs, plants, and other animal species). Remains accumulated in streams and shallow lakes and were swiftly buried (and preserved) by sediments associated with those environments. Scientists believe these sediments in turn were lithified over many millions of years as they were buried under younger deposits -- forming the distinctive stratigraphy of the Monument. The generally flat-laying "layer cake" geology of the region -- similar to the Colorado Plateau to the south - is expressed in the image by parallel beds of tan, reddish-brown, and gray-brown sedimentary rocks cut by the Yampa River at the northern end of the Monument (top). Erosion by the Yampa River exposed the Morrison layer and its trove of fossil material. Together with other fossils found in both older and younger rock layers in the area, the Dinosaur National Monument remains an important scientific resource that continues to provide new insights into the geologic history and paleoecology of the region.

Earth Observations taken by the Expedition 15 Crew

NASA Image and Video Library

2007-09-12

ISS015-E-28001 (12 Sept. 2007) --- A section of Dinosaur National Monument along the Yampa River in Colorado, which straddles the Colorado/Utah border, is featured in this image photographed by an Expedition 15 crewmember on the International Space Station. Dinosaur National Monument is perhaps best known for the abundant fossils found in the approximately 145 Ma (mega-annum, or millions of years old) Morrison Formation exposed in valleys and low ridges, according to scientists. The fossil assemblage is a unique record of terrestrial life of the period (dinosaurs, plants, and other animal species). Remains accumulated in streams and shallow lakes and were swiftly buried (and preserved) by sediments associated with those environments. Scientists believe these sediments in turn were lithified over many millions of years as they were buried under younger deposits -- forming the distinctive stratigraphy of the Monument. The generally flat-laying "layer cake" geology of the region -- similar to the Colorado Plateau to the south - is expressed in the image by parallel beds of tan, reddish-brown, and gray-brown sedimentary rocks cut by the Yampa River at the northern end of the Monument (top). Erosion by the Yampa River exposed the Morrison layer and its trove of fossil material. Together with other fossils found in both older and younger rock layers in the area, the Dinosaur National Monument remains an important scientific resource that continues to provide new insights into the geologic history and paleoecology of the region.

Earth Observations taken by the Expedition 15 Crew

NASA Image and Video Library

2007-09-12

ISS015-E-28004 (12 Sept. 2007) --- A section of Dinosaur National Monument along the Yampa River in Colorado, which straddles the Colorado/Utah border, is featured in this image photographed by an Expedition 15 crewmember on the International Space Station. Dinosaur National Monument is perhaps best known for the abundant fossils found in the approximately 145 Ma (mega-annum, or millions of years old) Morrison Formation exposed in valleys and low ridges, according to scientists. The fossil assemblage is a unique record of terrestrial life of the period (dinosaurs, plants, and other animal species). Remains accumulated in streams and shallow lakes and were swiftly buried (and preserved) by sediments associated with those environments. Scientists believe these sediments in turn were lithified over many millions of years as they were buried under younger deposits -- forming the distinctive stratigraphy of the Monument. The generally flat-laying "layer cake" geology of the region -- similar to the Colorado Plateau to the south - is expressed in the image by parallel beds of tan, reddish-brown, and gray-brown sedimentary rocks cut by the Yampa River at the northern end of the Monument (top). Erosion by the Yampa River exposed the Morrison layer and its trove of fossil material. Together with other fossils found in both older and younger rock layers in the area, the Dinosaur National Monument remains an important scientific resource that continues to provide new insights into the geologic history and paleoecology of the region.

Earth Observations taken by the Expedition 15 Crew

NASA Image and Video Library

2007-09-12

ISS015-E-28003 (12 Sept. 2007) --- A section of Dinosaur National Monument along the Yampa River in Colorado, which straddles the Colorado/Utah border, is featured in this image photographed by an Expedition 15 crewmember on the International Space Station. Dinosaur National Monument is perhaps best known for the abundant fossils found in the approximately 145 Ma (mega-annum, or millions of years old) Morrison Formation exposed in valleys and low ridges, according to scientists. The fossil assemblage is a unique record of terrestrial life of the period (dinosaurs, plants, and other animal species). Remains accumulated in streams and shallow lakes and were swiftly buried (and preserved) by sediments associated with those environments. Scientists believe these sediments in turn were lithified over many millions of years as they were buried under younger deposits -- forming the distinctive stratigraphy of the Monument. The generally flat-laying "layer cake" geology of the region -- similar to the Colorado Plateau to the south - is expressed in the image by parallel beds of tan, reddish-brown, and gray-brown sedimentary rocks cut by the Yampa River at the northern end of the Monument (top). Erosion by the Yampa River exposed the Morrison layer and its trove of fossil material. Together with other fossils found in both older and younger rock layers in the area, the Dinosaur National Monument remains an important scientific resource that continues to provide new insights into the geologic history and paleoecology of the region.

Acoustic Velocity Of The Sediments Offshore Southwestern Taiwan

NASA Astrophysics Data System (ADS)

Tsai, C.; Liu, C.; Huang, P.

2004-12-01

Along the Manila Trench south of 21øXN, deep-sea sediments are being underthrusted beneath the Taiwan accretionary prism which is composed of the Kaoping Slope and Hengchun Ridge. Offshore southwestern Taiwan, foreland sediments and Late Miocene strata of the Tainan Basin are being accreted onto the fold-and thrust belt of the syn-collision accretionary wedge of the Kaoping Slope. The Kaoping Slope consists of thick Neogene to Recent siliciclastics deformed by fold-and-thrust structures and mud diapers. These Pliocene-Quaternary sediments deposited in the Kaoping Shelf and upper slope area are considered to be paleo-channel deposits confined by NNE-SSW trend mud diapiric structure. Seismic P-wave velocities of the sediment deposited in the Kaoping Shelf and Kaoping Slope area are derived from mutichannel seismic reflection data and wide-angle reflection and refraction profiles collected by sonobuoys. Sediment velocity structures constrained from mutichannel seismic reflection data using velocity spectrum analysis method and that derived from sonobuoy data using tau-sum inversion method are compared, and they both provide consistent velocity structures. Seismic velocities were analyzed along the seismic profile from the surface to maximum depths of about 2.0 km below the seafloor. Our model features a sediment layer1 with 400 ms in thickness and a sediment layer2 with 600 ms in thickness. For the shelf sediments, we observe a linear interval velocity trend of V=1.53+1.91T in layer1, and V=1.86+0.87T in layer2, where T is the one way travel time within the layer. For the slop sediment, the trend of V=1.47+1.93T in layer1, and V=1.70+1.55T in layer2. The layer1¡¦s velocities gradients are similar between the shelf (1.91 km/sec2) and the slope(1.93 km/sec2). It means layer1 distributes over the slope and shelf widely. The result of the sediment velocity gradients in this area are in good agreement with that reported for the south Atlantic continental margins.

An Investigation of Instantaneous Plume Rise from Rocket Exhaust

DTIC Science & Technology

1996-12-01

METERS) TOP = 2973.48 BASE= 210.62 SIGMAR (AZ) AT THE SURFACE (DEGREES) 13.5054 SIGMER(EL) AT THE SURFACE (DEGREES) 2.9738 MET. WIND WIND LAYER WIND SPEED...SELECTED LAYER HEIGHT- (METERS) TOP = 2973.48 BASE= 210.62 SIGMAR (AZ) AT THE SURFACE (DEGREES) 13.6911 SIGMER(EL) AT THE SURFACE (DEGREES) 2.9738 MET...TIME (SECS) 368.08 FIRST MIXING LAYER HEIGHT- (METERS) TOP = 210.62 BASE= 0.00 SECOND SELECTED LAYER HEIGHT- (METERS) TOP = 2973.48 BASE= 210.62 SIGMAR

Turbidity Currents With Equilibrium Basal Driving Layers: A Mechanism for Long Runout

NASA Astrophysics Data System (ADS)

Luchi, R.; Balachandar, S.; Seminara, G.; Parker, G.

2018-02-01

Turbidity currents run out over 100 km in lakes and reservoirs, and over 1,000 km in the ocean. They do so without dissipating themselves via excess entrainment of ambient water. Existing layer-averaged formulations cannot capture this. We use a numerical model to describe the temporal evolution of a turbidity current toward steady state under condition of zero net sediment flux at the bed. The flow self-partitions itself into two layers. The lower "driving layer" approaches an invariant flow thickness, velocity profile, and suspended sediment concentration profile that sequesters nearly all of the suspended sediment. This layer can continue indefinitely at steady state over a constant bed slope. The upper "driven layer" contains a small fraction of the suspended sediment. The devolution of the flow into these two layers likely allows the driving layer to run out long distances.

Plasmon absorption modulator systems and methods

DOEpatents

Kekatpure, Rohan Deodatta; Davids, Paul

2014-07-15

Plasmon absorption modulator systems and methods are disclosed. A plasmon absorption modulator system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and a metal layer formed on a top surface of the stack of quantum well layers. A method for modulating plasmonic current includes enabling propagation of the plasmonic current along a metal layer, and applying a voltage across the stack of quantum well layers to cause absorption of a portion of energy of the plasmonic current by the stack of quantum well layers. A metamaterial switching system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and at least one metamaterial structure formed on a top surface of the stack of quantum well layers.

Anoxic sediments off Central Peru record interannual to multidecadal changes of climate and upwelling ecosystem during the last two centuries

NASA Astrophysics Data System (ADS)

Gutiérrez, D.; Sifeddine, A.; Reyss, J. L.; Vargas, G.; Velazco, F.; Salvatteci, R.; Ferreira, V.; Ortlieb, L.; Field, D.; Baumgartner, T.; Boussafir, M.; Boucher, H.; Valdés, J.; Marinovic, L.; Soler, P.; Tapia, P.

2006-01-01

High-resolution paleo-environmental and paleo-ecological archives in laminated sequences are present in selected areas from the upper continental Peruvian margin within the oxygen minimum zone. We present initial results of a multidisciplinary study (the PALEOPECES project) that aims to reconstruct environmental and ecosystem variability during the past 200 years from high-resolution records. We report chronology development, sediment structure, elemental, organic, and mineralogical compositions of a box core collected at 300 m depth off Pisco, central Peru. An average sedimentation rate of 2.2 mm y-1 was estimated from downcore excess 210Pb activities for the last 100-150 years. Extending this rate further downcore indicates that a slump located at 52 cm depth from the top of the core can be correlated with a large tsunami that struck the coast of central Peru in 1746. X-ray analyses reveal laminated structures composed of couplets of light and dark laminae. Observations under polarized microscope show that light laminae are dominated by more dense, detrital and terrigenous material, while dark laminae are less dense with greater concentrations of amorphous biogenic silica. Downcore variations in dry bulk density and X-ray radioscopy of gray level show similar patterns, including a major shift at 34 cm depth (ca. mid-nineteenth century). A finely laminated sequence, which may include annual varves, is present between 34 cm depth and the slump layer. Sediment characteristics of the sequence suggest increased seasonality of terrigenous versus biogenous sedimentation during the corresponding period. In addition to a mid-nineteenth century change and considerable multidecadal variability in TOC, there is a positive trend in the past 50 years. Mineralogical analyses from a Fourier Transformed Infrared Spectroscopy (FTIR) of the upper core covering the last 25 years, indicate higher concentrations of the mineral fraction (quartz, feldspar, kaolinite and illite) in layers including large El Niño events (1982-1983, 1986-1987 and 1997-1998), with the largest peak during the 1997-1998 episode. These results confirm that anoxic sediments off Pisco are suitable archives to investigate interannual and decadal changes in oceanographic conditions and climate of the northern Humboldt upwelling system.

Methane Ebullition During Simulated Lake Expansion and Permafrost Degradation

NASA Astrophysics Data System (ADS)

Mazéas, O.; von Fischer, J. C.; Whelan, M.; Rhew, R.

2007-12-01

Methane, a potent greenhouse gas, is emitted by Arctic tundra and lakes. Ebullition, or bubbling, of methane from Arctic lakes has been shown to be a major transport mechanism from the sediment to the atmosphere, and ebullition rates are greatest near the edges of the lakes where active erosion is occurring. In regions of continuous permafrost, Arctic lakes have been expanding in recent decades, attributed to permafrost melting and development of thermokarst. Lake expansion occurs when the margins erode into water, supplying large amounts of organic rich material to the sediment-water interface. This allows carbon that was previously stored in the soil (active layer and permafrost) to become bioavailable and subject to decomposition. An increase in Arctic methane emissions as a result of permafrost thawing and lake expansion would constitute a positive feedback to Arctic warming. In order to better understand these processes, an experiment was initiated in July 2007 at the Barrow Environmental Observatory, Barrow, AK. Different layers of locally collected tundra soil were placed into incubation chambers at the bottom of a shallow (about 1 m deep) lake. Each experimental chamber consists of a bucket fixed underneath an inverted funnel, with a sampling port on top to capture and collect the emitted gases. Gas samples are analyzed for methane and carbon dioxide concentrations, as well as relevant isotopic compositions. Gas sampling has occurred at frequent intervals during the late summer and will continue through the early winter. Three replicates of each layer (active layer, seasonally frozen active layer and permafrost) were incubated, as well as an empty control chamber. An additional chamber containing thawed permafrost and cellulose-rich sawdust was placed for comparison, as cellulose is a major component of plant tissue and the fermentation of the cellulose should yield substrates for methanogenesis. Total production of methane versus organic carbon content of initial sample, kinetics of ebullition, and relative potential emissions from each tundra layer will be assessed.

Neogene deformation of thrust-top Rzeszów Basin (Outer Carpathians, Poland)

NASA Astrophysics Data System (ADS)

Uroda, Joanna

2015-04-01

The Rzeszów Basin is a 220 km2 basin located in the frontal part of Polish Outer Carpathians fold-and-thrust belt. Its sedimentary succession consist of ca. 600 m- thick Miocene evaporates, litoral and marine sediments. This basin developed between Babica-Kąkolówka anticline and frontal thrust of Carpathian Orogen. Rzeszów thrust-top basin is a part of Carpathian foreland basin system- wedge-top depozone. The sediments of wedge -top depozone were syntectonic deformed, what is valuable tool to understand kinematic history of the orogen. Analysis of field and 3D seismic reflection data showed the internal structure of the basin. Seismic data reveal the presence of fault-bend-folds in the basement of Rzeszów basin. The architecture of the basin - the presence of fault-releated folds - suggest that the sediments were deformed in last compressing phase of Carpathian Orogen deformation. Evolution of Rzeszów Basin is compared with Bonini et.al. (1999) model of thrust-top basin whose development is controlled by the kinematics of two competing thrust anticlines. Analysis of seismic and well data in Rzeszów basin suggest that growth sediments are thicker in south part of the basin. During the thrusting the passive rotation of the internal thrust had taken place, what influence the basin fill architecture and depocentre migration opposite to thrust propagation. Acknowledgments This study was supported by grant No 2012/07/N/ST10/03221 of the Polish National Centre of Science "Tectonic activity of the Skole Nappe based on analysis of changes in the vertical profile and depocentre migration of Neogene sediments in Rzeszów-Strzyżów area (Outer Carpathians)". Seismic data by courtesy of the Polish Gas and Oil Company. References Bonini M., Moratti G., Sani F., 1999, Evolution and depocentre migration in thrust-top basins: inferences from the Messinian Velona Basin (Northern Apennines, Italy), Tectonophysics 304, 95-108.

Analysis of seismograms from a downhole array in sediments near San Francisco Bay

USGS Publications Warehouse

Joyner, William B.; Warrick, Richard E.; Oliver, Adolph A.

1976-01-01

A four-level downhole array of three-component instruments was established on the southwest shore of San Francisco Bay to monitor the effect of the sediments on low-amplitude seismic ground motion. The deepest instrument is at a depth of 186 meters, two meters below the top of the Franciscan bedrock. Earthquake data from regional distances (29 km ≤ Δ ≤ 485 km) over a wide range of azimuths are compared with the predictions of a simple plane-layered model with material properties independently determined. Spectral ratios between the surface and bedrock computed for the one horizontal component of motion that was analyzed agree rather well with the model predictions; the model predicts the frequencies of the first three peaks within 10 percent in most cases and the height of the peaks within 50 percent in most cases. Surface time histories computed from the theoretical model predict the time variations of amplitude and frequency content reasonably well, but correlations of individual cycles cannot be made between observed and predicted traces.

Understanding Mississippi Delta Subsidence through Stratigraphic and Geotechnical Analysis of a Continuous Holocene Core at a Subsidence Superstation

NASA Astrophysics Data System (ADS)

Bridgeman, J.; Tornqvist, T. E.; Jafari, N.; Allison, M. A.

2017-12-01

Land-surface subsidence can be a major contributor to the relative sea-level rise that is threatening coastal communities. Loosely constrained subsidence rate estimates across the Mississippi Delta make it difficult to differentiate between subsidence mechanisms and complicate modeling efforts. New data from a nearly 40 m long, 12 cm diameter core taken during the installation of a subsidence monitoring superstation near the Mississippi River, SW of New Orleans, provides insight into the stratigraphic and geotechnical properties of the Holocene succession. Stratigraphically, the core can be grouped into three sections. The top 12 m is dominated by clastic overbank sediment with interspersed organic-rich layers. The middle section, 12-35 m consists predominately of mud, and the bottom section, 35-38.7 m, is marked by a transition into a Holocene-aged basal peat (11,350-11,190 cal BP) which overlies densely packed Pleistocene sediment. Radiocarbon and OSL ages show up to 6 m of vertical displacement since 3,000 cal BP. We infer that most of this was due to compaction of the thick underlying mud package. The top ­­­­­ 70 cm of the core is a peat that represents the modern marsh surface and is inducing minimal surface loading. This is consistent with the negligible shallow subsidence rate as seen at a nearby rod-surface elevation table - marker horizon station and the initial strainmeter data. Future compaction scenarios for the superstation can be modeled from the stratigraphic and geotechnical properties of the core, including the loading from the planned Mid-Barataria sediment diversion which is expected to dramatically change the coastal landscape in this region.

Generation of net sediment transport by velocity skewness in oscillatory sheet flow

NASA Astrophysics Data System (ADS)

Chen, Xin; Li, Yong; Chen, Genfa; Wang, Fujun; Tang, Xuelin

2018-01-01

This study utilizes a qualitative approach and a two-phase numerical model to investigate net sediment transport caused by velocity skewness beneath oscillatory sheet flow and current. The qualitative approach is derived based on the pseudo-laminar approximation of boundary layer velocity and exponential approximation of concentration. The two-phase model can obtain well the instantaneous erosion depth, sediment flux, boundary layer thickness, and sediment transport rate. It can especially illustrate the difference between positive and negative flow stages caused by velocity skewness, which is considerably important in determining the net boundary layer flow and sediment transport direction. The two-phase model also explains the effect of sediment diameter and phase-lag to sediment transport by comparing the instantaneous-type formulas to better illustrate velocity skewness effect. In previous studies about sheet flow transport in pure velocity-skewed flows, net sediment transport is only attributed to the phase-lag effect. In the present study with the qualitative approach and two-phase model, phase-lag effect is shown important but not sufficient for the net sediment transport beneath pure velocity-skewed flow and current, while the asymmetric wave boundary layer development between positive and negative flow stages also contributes to the sediment transport.

Impact of sedimentation on wetland carbon sequestration in an agricultural watershed.

PubMed

McCarty, Gregory; Pachepsky, Yakov; Ritchie, Jerry

2009-01-01

Landscape redistribution of soil C is common within agricultural ecosystems. Little is known about the effects of upland sediment deposition on C dynamics within riparian wetlands. To assess sedimentation impact, we obtained profile samples of wetland soil and used the combination of (137)Cs, (210)Pb, and (14)C chronological markers to determine rates of C sequestration and mineral deposition over the history of a wetland within a first-order catchment under agricultural management in the coastal plains of the United States. Substantial post settlement deposition in the wetland soil was evidenced in places by a 20- to 40-cm layer of mineral soil that buried the original histosol. Soil profiles contained a minimum in C content within the top 35 cm of the profile which originated from a rapid deposition from low C upland soils. Radiocarbon and radioisotope dating showed that increases in C above this minimum were the result of C sequestered in the past approximately 50 yr. Modeling the kinetics of modern C dynamics using the (137)Cs and (210)Pb markers within these surface profiles provides strong evidence for accelerated C sequestration associated with mineral sediment deposition in the ecosystem. These findings indicate that at the landscape scale, dilution of ecosystem C by import of low C upland sediment into wetlands stimulates C sequestration by pulling soil C content below some pedogenic equilibrium value for the ecosystem. They also indicate that over the history of the wetland, rates of C accretion may be linked to mineral soil deposition.

Non-halide sediments from the Loule diapir salt mine: characterization and environmental significance

NASA Astrophysics Data System (ADS)

Ribeiro, Carlos; Terrinha, Pedro; Andrade, Alexandre; Fonseca, Bruno; Caetano, Miguel; Neres, Marta; Font, Eric; Mirão, José; Dias, Cristina; Rosado, Lúcia; Maurer, Anne-France; Manhita, Ana

2017-04-01

The sedimentary record of the Mesozoic Algarve Basin (south Portugal) spans from the Triassic to the Lower Cretaceous. Following the initial phase of Pangaea breakup and the related continental sedimentation during the Triassic, the sedimentation evolved through transitional (Triassic-Jurassic transition) to marine (Jurassic) environments. During the Hettangian a thick sequence of evaporites deposited in the basin. Most of the occurrences of these deposits have undetermined volumes, due to the post depositional diapiric movements. At the central Algarve, under the town of Loulé, a salt wall of up to > 1 km across, > 3 km in length and > 2 km in height has been exploited for the chemical industry (Loulé Diapir - LD). Most of the sediments that constitute LD are halides (> 99% halite), the exception being a package of non-halide sediments, constituted by carbonates (dolomite and magnesite) and sulphates (anhydrite) in various proportions with a maximum thickness of 3 meters. This package has a distinctive mesoscopic aspect of three layers of approximately the same thickness, different colours and primary sedimentary structures: black-brow-grey, from bottom to top. The sediments of this package were studied with a multidisciplinary approach aiming their mineralogical and chemical characterization, the determination of the organic matter content and origin, as well as the characterization and understanding of the chemical processes that occurred during the emplacement and compression of the LD: (i) X-ray diffraction for the determination of the mineral phases present and semi-quantification using the RIR-Reference Intensity Ratio method; (ii) micro analysis of the mineralogical samples by Scanning Electron Microscopy coupled to Energy Dispersive Spectroscopy; (iii) REE content determination by ICP-MS; (iv) determination of the carbon content by CHN Elemental analysis; (v) determination of the organic matter content by elemental analysis and their composition by pyrolysis-GC-MS; (vi) determination of the carbon and nitrogen stable isotopic ratios of the organic matter; (vii) anisotropy of the magnetic susceptibility to study it emplacement mode. The LD is deformed by a set of shear-zones and thrusts formed during the Cenozoic Alpine compression that are underlined by the presence of a fine grained, non-halide material, whose nature and characterization was also done, using the same analytical methods. The preliminary mineralogical and geochemical results show a clear pattern in the evolution of the environmental conditions of the sedimentation with influence on the availability of the dissolved cations. The three of the sediment package showed distinct organic carbon content reaching 4.42% in the black horizon, five times the values found in the adjacent layers. By using the rare earth elements as geochemical tracers of sediment provenance, shale normalised profiles suggest that sediment particles from the three layers have the same origin. However, the non-halide sediments retained in the shear zones showed a different profile with an increase of MREE and a positive Eu anomaly. This work was done in the scope of the MEDSALT - Uncovering the Mediterranean salt giant, COST action CA15103.

Early diagenetic processes of saline meromictic Lake Kai-ike, southwest Japan: III. Sulfur speciation and isotopes

NASA Astrophysics Data System (ADS)

Sakai, N.; Yamaguchi, K. E.; Oguri, K.

2014-12-01

Lake Kai-ike is a saline meromictic lake located along the coast of Kami-Koshiki Island. The lake is isolated from ocean by a gravel bar, through which seawater infiltrates by tidal pumping. The lake is permanently redox (density)-stratified with a mid-depth development of photic zone anoxia and a dense community of photosynthetic bacteria pinkish "bacterial plate". The early diagenesis of sulfur in sediments overlain by an anoxic water body was investigated using a sediment core (KAI4) from the lake. We determined abundance of various S-bearing species (i.e., Cr-reducible sulfide (= pyrite S: Spy), acid-volatile sulfide (AVS), sulfate sulfur (SSO4), elemental sulfur (S0), and organic sulfur) by an improved sequential extraction method. Here we focus on drastic and rapid changes on sulfur biogeochemistry found in the uppermost 5cm layer. With increasing depth, abundance of Spy increased but that of SSO4 and δ34S value of Spy (δ34Spy) decreased. These results suggest progressive formation of bacteriogenic pyrite. The δ34S values of SSO4 (δ34SSO4) ranged from 25.1 ‰ (at sediment surface) to 3.8 ‰ in the uppermost 5 cm layer. This δ34SSO4 decrease in the top 5 cm sediment suggests that SSO4 in the surface sediment inherits SO42- with elevated δ34S values (higher than typical seawater δ34S value of 21‰) in the water column, which is due to extensive bacterial sulfate reduction with preferential removal of low-δ34S sulfur as sulfide. In the lower part of the uppermost 5 cm layer, SO42- formed by oxidation of S0, AVS, and/or Spy with low-δ34S values by SO42--bearing seawater introduced by infiltration through the gravel bar. Increasing δ34Spy values with increasing depth suggest near complete consumption of SO42- by active bacterial sulfate reduction, and this process could be explained by Rayleigh distillation model. Early diagenesis of sulfur does occur in whole section of 25cm-long KAI4 core that accumulated for the last ~60 years (Yamaguchi et al., 2010; Palaeo3). Geochemical characteristics of sulfur in the uppermost part of Lake Kai-ike sediment were significantly modified during early diagenesis. Such diagenetic modification for sulfur isotopes should be fully taken into account to better reconstruct past anoxic environment such as Cretaceous OAEs and Archean oceans.

Rehabilitation options for inland waterways impacted by sulfidic sediments--field trials in a south-eastern Australian wetland.

PubMed

Fraser, Mark A; Baldwin, Darren S; Rees, Gavin N; Silvester, Ewen J; Whitworth, Kerry L

2012-07-15

The accumulation of significant pools of sulfidic sediments in inland wetlands and creeks is an emerging risk for the management of inland waterways. We used replicated plot trials to appraise the viability of various strategies for neutralizing oxidized, acidified sulfidic sediments in a highly degraded wetland. Of the twenty different treatments trialed only addition of calcium hydroxide or calcium carbonate, burning of wood, and planting of Phragmites australis, Typha domingensis and Atriplex nummularia into beds prepared with CaCO3 or P. australis and T. domingensis into beds of sediment and mulch, decreased total actual acidity (TAA) in the top 5 cm of sediment in the first two weeks following treatment. Only the calcium hydroxide treatments and planting of P. australis, T. domingensis and A. nummularia into beds prepared with CaCO3 decreased TAA for a longer period of time (6 months). None of the treatments, except the planting of P. australis into beds prepared with lime, decreased TAA in the 5-30 cm layer of sediments. Therefore, the only effective treatment appears to be the application of highly alkaline ameliorants which need to be transported to the site. A survey of the wetland was undertaken to estimate the total amount of actual and potential acidity stored in the wetland's sediment and overlying water and showed that up to 1200 tonnes of calcium carbonate would be required to neutralise all of the actual and potential acidity in the 10 ha wetland. However, neutralisation of the remaining water in the wetland (about 12.5 ML) would produce approximately 2750 m3 of metal rich sludge (approximately 100 tonnes dry weight) that would require separate disposal. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Effects of Desert Dust on Nutrient Cycling in the San Juan Mountains, Colorado

NASA Astrophysics Data System (ADS)

Neff, J. C.; Farmer, L.; Painter, T. H.; Landry, C.; Reynolds, R.

2005-12-01

The San Juan Mountains of southwestern Colorado lie downwind from several major deserts and experience several dust-deposition events each year. These events appear related to storms that erode soils in the deserts of the western US and then deposit atmospheric dust from these soils during or after snowfall during large late winter and spring deposition events. To evaluate the biogeochemical implications of eolian deposition, we collected dust from distinct layers deposited into the seasonal snowpack. We also sampled soils and lake sediments in a high-elevation catchment in the San Juan Mountains. Atmospheric dust was characterized by measurements of chemical composition, Sr isotopic content and analysis of the organic and inorganic constituents of deposited eolian material. The origins of snowpack dust in the San Juans were analyzed using atmospheric tracer transport modeling. These analyses suggest that many dust events originate in southern Utah and northern Arizona, areas that have undergone substantial land use change through the 20th century and that experience severe wind erosion of soils during periodic severe droughts. Analyses of 87Sr/86Sr isotope ratios dust, soils, bedrock, and sediments suggest that eolian dust may compose as much as 90% of the near-surface soil (top 5 cm). In alpine lake sediments, Sr isotopes suggest a relatively recent (20th century) increase in the fraction of sediments derived from dust (relative to bedrock) and a similarly large contribution of dust to surface sediments. Sediment chemistry in two small alpine tarns show changes in Ca, Mg, Al, and Fe concentrations that imply increasing dust (vs. bedrock) contributions to lake sediments over the past 100-200 years. Increasing loading of Ca, Mg and P to alpine basins may have implications for alpine and sub-alpine biogeochemical cycling including water quality and plant nutrient use.

Bioturbation delays attenuation of DDT by clean sediment cap but promotes sequestration by thin-layered activated carbon.

PubMed

Lin, Diana; Cho, Yeo-Myoung; Werner, David; Luthy, Richard G

2014-01-21

The effects of bioturbation on the performance of attenuation by sediment deposition and activated carbon to reduce risks from DDT-contaminated sediment were assessed for DDT sediment-water flux, biouptake, and passive sampler (PE) uptake in microcosm experiments with a freshwater worm, Lumbriculus variegatus. A thin-layer of clean sediment (0.5 cm) did not reduce the DDT flux when bioturbation was present, while a thin (0.3 cm) AC cap was still capable of reducing the DDT flux by 94%. Bioturbation promoted AC sequestration by reducing the 28-day DDT biouptake (66%) and DDT uptake into PE (>99%) compared to controls. Bioturbation further promoted AC-sediment contact by mixing AC particles into underlying sediment layers, reducing PE uptake (55%) in sediment compared to the AC cap without bioturbation. To account for the observed effects from bioturbation, a mass transfer model together with a biodynamic model were developed to simulate DDT flux and biouptake, respectively, and models confirmed experimental results. Both experimental measurements and modeling predictions imply that thin-layer activated carbon placement on sediment is effective in reducing the risks from contaminated sediments in the presence of bioturbation, while natural attenuation process by clean sediment deposition may be delayed by bioturbation.

Hybrid Dye-Sensitized Solar Cells Consisting of Double Titania Layers for Harvesting Light with Wide Range of Wavelengths

NASA Astrophysics Data System (ADS)

Sadamasu, Kengo; Inoue, Takafumi; Ogomi, Yuhei; Pandey, Shyam S.; Hayase, Shuzi

2011-02-01

We report a hybrid dye-sensitized solar cell consisting of double titania layers (top and bottom layers) stained with two dyes. A top layer fabricated on a glass was mechanically pressed with a bottom layer fabricated on a glass cloth. The glass cloth acts as a supporter of a porous titania layer as well as a holder of electrolyte. The incident photon to current efficiency (IPCE) curve had two peaks corresponding to those of the two dyes, which demonstrates that electrons are collected from both the top and bottom layers.

Interior trough deposits on Mars: Subice volcanoes?

USGS Publications Warehouse

Chapman, M.G.; Tanaka, K.L.

2001-01-01

Widespread, several-kilometer-thick successions of layered deposits occur as mounds that partly fill the troughs or chasmata that compose the Valles Marineris on Mars. Like terrestrial subice volcanoes, the layered deposits occur in a volcano-tectonic setting within basins that may have held ponded water or ice. On the basis of their dimensions, morphologies, and associated catastrophic floods and other geologic events as shown in Viking and new Mars Global Surveyor (MGS) data sets, we suggest that the interior deposits are volcanic in origin and possibly generated by subice eruptions. A tuya origin for the mounds can explain the lack of external sediment, mound heights that can rival the plateau, local flat-topped mesas, morphologically distinct mounds of different ages, horizontal to steep dips, fine-grained materials, indications of rare volcanic vents and lava flows, and spectral composition. The extremely diverse layering of west Candor Chasma and possible volcanic cones in Melas may have formed by related subaerial eruptions. Consistent with the suggestion that interior deposits are eroding out of the wall rock, some deposits could have been erupted from sites along the walls.

Role of storms and forest practices in sedimentation of an Oregon Coast Range lake

NASA Astrophysics Data System (ADS)

Richardson, K.; Hatten, J. A.; Wheatcroft, R. A.; Guerrero, F. J.

2014-12-01

The design of better management practices in forested watersheds to face climate change and the associated increase in the frequency of extreme events requires a better understanding of watershed responses to extreme events in the past and also under management regimes. One of the most sensitive watershed processes affected is sediment yield. Lake sediments record events which occur in a watershed and provide an opportunity to examine the interaction of storms and forest management practices in the layers of the stratigraphy. We hypothesize that timber harvesting and road building since the 1900s has resulted in increases in sedimentation; however, the passage of the Oregon Forest Practices Act (OFPA) in 1972 has led to a decrease in sedimentation. Sediment cores were taken at Loon Lake in the Oregon Coast Range. The 32-m deep lake captures sediment from a catchment highly impacted by recent land use and episodic Pacific storms. We can use sedimentological tools to measure changes in sediment production as motivated by extreme floods before settlement, during a major timber harvesting period, and after installation of forestry Best Management Practices. Quantification of changes in particle size and elemental composition (C, N, C/N) throughout the cores can elucidate changes in watershed response to extreme events, as can changes in layer thickness. Age control in the cores is being established by Cesium-137 and radiocarbon dating. Given the instrumental meteorological data and decadal climate reconstructions, we will disentangle climate driven signals from changes in land use practices. The sediment shows distinct laminations and varying thickness of layers throughout the cores. Background deposition is composed of thin layers (<0.5 cm) of fine silts and clays, punctuated by thicker layers (3-25 cm) every 10 to 75 cm. These thick layers consist of distinctly textured units, generally fining upward. We interpret the thick layers in Loon Lake to be deposited by sediment-producing floods throughout much of the 1500-year lifespan of this lake. We will explore the relationship between sedimentation, land use, and climate forcing events to determine if the OFPA is having an effect on reducing sedimentation rates as a result of extreme magnitude storm events.

Annually laminated lake sediments as recorders of flood events: evidence from combining monitoring and calibration

NASA Astrophysics Data System (ADS)

Kämpf, Lucas; Brauer, Achim; Mueller, Philip; Güntner, Andreas; Merz, Bruno

2015-04-01

The relation of changing climate and the occurrence of strong flood events has been controversially debated over the last years. One major limitation in this respect is the temporal extension of instrumental flood time series, rarely exceeding 50-100 years, which is too short to reflect the full range of natural climate variability in a region. Therefore, geoarchives are increasingly explored as natural flood recorders far beyond the range of instrumental flood time series. Annually laminated (varved) lake sediments provide particularly valuable archives since (i) lakes form ideal traps in the landscape continuously recording sediment flux from the catchment and (ii) individual flood events are recorded as detrital layers and can be dated with seasonal precision by varve counting. Despite the great potential of varved lake sediments for reconstructing long flood time series, there are still some confinements with respect to their interpretation due to a lack in understanding processes controlling the formation of detrital layers. For this purpose, we investigated the formation of detrital flood layers in Lake Mondsee (Upper Austria) in great detail by monitoring flood-related sediment flux and comparing detrital layers in sub-recent sediments with river runoff data. Sediment flux at the lake bottom was trapped over a three-year period (2011-2013) at two locations in Lake Mondsee, one located 0.9 km off the main inflow (proximal) and one in a more distal position at a distance of 2.8 km. The monitoring data include 26 floods of different amplitude (max. hourly discharge=10-110 cbm/s) which triggered variable fluxes of catchment sediment to the lake floor (4-760 g/(sqm*d)). The comparison of runoff and sediment data revealed empiric runoff thresholds for triggering significant detrital sediment influx to the proximal (20 cbm/s) and distal lake basin (30 cbm/s) and an exponential relation between runoff amplitude and the amount of deposited sediment. A succession of 20 sub-millimetre to maximum 8 mm thick flood-triggered detrital layers, deposited between 1976 and 2005, was detected in two varved surface sediment cores from the same locations as the sediment traps. Calibration of the detrital layer record with river runoff data revealed empirical thresholds for flood layer deposition. These thresholds are higher than those for trapped sediment flux but, similarly to the trap results, increasing from the proximal (50-60 cbm/s; daily mean=40 cbm/s) to the distal lake basin (80 cbm/s, 2 days>40 cbm/s). Three flood events above the threshold for detrital layer formation in the proximal and one in the distal lake basin were also recorded in the monitoring period. These events resulted in exceptional sediment transfer to the lake of more than 400 g/sqm at both sites, which is therefore interpreted as the minimum sediment amount for producing a visible detrital layer.

Sheet flow and suspended sediment due to wave groups in a large wave flume

USGS Publications Warehouse

Dohmen-Janssen, C. M.; Hanes, D.M.

2005-01-01

A series of sand bed experiments was carried out in the Large Wave Flume in Hannover, Germany as a component of the SISTEX99 experiment. The experiments focussed on the dynamic sediment response due to wave group forcing over a flat sand bed in order to improve understanding of cross-shore sediment transport mechanisms and determine sediment concentrations, fluxes and net transport rates under these conditions. Sediment concentrations were measured within the sheet flow layer (thickness in the order of 10 grain diameters) and in the suspension region (thickness in the order of centimetres). Within the sheet flow layer, the concentrations are highly coherent with the instantaneous near-bed velocities due to each wave within the wave group. However, in the suspension layer concentrations respond much more slowly to changes in near-bed velocity. At several centimetres above the bed, the suspended sediment concentrations vary on the time scale of the wave group, with a time delay relative to the peak wave within the wave group. The thickness of the sheet flow changes with time. It is strongly coherent with the wave forcing, and is not influenced by the history or sequence of the waves within the group. The velocity of the sediment was also measured within the sheet flow layer some of the time (during the larger wave crests of the group), and the velocity of the fluid was measured at several cm above the sheet flow layer. The grain velocity and concentration estimates can be combined to estimate the sediment flux. The estimates were found to be consistent with previous measurements under monochromatic waves. Under these conditions, without any significant mean current, the sediment flux within the sheet flow layer was found to greatly exceed the sediment flux in the suspension layer. As a result, net transport rates under wave groups are similar to those under monochromatic waves. ?? 2004 Elsevier Ltd. All rights reserved.

Investigating the influence of lithologic heterogeneity on gas hydrate formation and methane recycling at the base of the gas hydrate stability zone in channelized systems

NASA Astrophysics Data System (ADS)

Daigle, H.; Nole, M.; Cook, A.; Malinverno, A.

2017-12-01

In marine environments, gas hydrate preferentially accumulates in coarse-grained sediments. At the meso- to micro-scale, however, hydrate distribution in these coarse-grained units is often heterogeneous. We employ a methane hydrate reservoir simulator coupling heat and mass transfer as well as capillary effects to investigate how capillary controls on methane solubility affect gas and hydrate accumulations in reservoirs characterized by graded bedding and alternating sequences of coarse-grained sands and fine-grained silt and clay. Simulations bury a channelized reservoir unit encased in homogeneous, fine-grained material characterized by small pores (150 nm) and low permeability ( 1 md in the absence of hydrate). Pore sizes within each reservoir bed between vary between coarse sand and fine silt. Sands have a median pore size of 35 microns and a lognormal pore size distribution. We also investigate how the amount of labile organic carbon (LOC) affects hydrate growth due to microbial methanogenesis within the sediments. In a diffusion-dominated system, methane movies into reservoir layers along spatial gradients in dissolved methane concentration. Hydrate grows in such a way as to minimize these concentration gradients by accumulating slower in finer-grained reservoir layers and faster in coarser-grained layers. Channelized, fining-upwards sediment bodies accumulate hydrate first along their outer surfaces and thence inward from top to bottom. If LOC is present in thin beds within the channel, higher saturations of hydrate will be distributed more homogeneously throughout the unit. When buried beneath the GHSZ, gas recycling can occur only if enough hydrate is present to form a connected gas phase upon dissociation. Simulations indicate that this is difficult to achieve for diffusion-dominated systems, especially those with thick GHSZs and/or small amounts of LOC. However, capillary-driven fracturing behavior may be more prevalent in settings with thick GHSZs.

Investigating the influence of lithologic heterogeneity on gas hydrate formation and methane recycling at the base of the gas hydrate stability zone in channelized systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daigle, Hugh; Nole, Michael; Cook, Ann

In marine environments, gas hydrate preferentially accumulates in coarse-grained sediments. At the meso- to micro-scale, however, hydrate distribution in these coarse-grained units is often heterogeneous. We employ a methane hydrate reservoir simulator coupling heat and mass transfer as well as capillary effects to investigate how capillary controls on methane solubility affect gas and hydrate accumulations in reservoirs characterized by graded bedding and alternating sequences of coarse-grained sands and fine-grained silt and clay. Simulations bury a channelized reservoir unit encased in homogeneous, fine-grained material characterized by small pores (150 nm) and low permeability (~1 md in the absence of hydrate). Poremore » sizes within each reservoir bed between vary between coarse sand and fine silt. Sands have a median pore size of 35 microns and a lognormal pore size distribution. We also investigate how the amount of labile organic carbon (LOC) affects hydrate growth due to microbial methanogenesis within the sediments. In a diffusion-dominated system, methane movies into reservoir layers along spatial gradients in dissolved methane concentration. Hydrate grows in such a way as to minimize these concentration gradients by accumulating slower in finer-grained reservoir layers and faster in coarser-grained layers. Channelized, fining-upwards sediment bodies accumulate hydrate first along their outer surfaces and thence inward from top to bottom. If LOC is present in thin beds within the channel, higher saturations of hydrate will be distributed more homogeneously throughout the unit. When buried beneath the GHSZ, gas recycling can occur only if enough hydrate is present to form a connected gas phase upon dissociation. Simulations indicate that this is difficult to achieve for diffusion-dominated systems, especially those with thick GHSZs and/or small amounts of LOC. However, capillary-driven fracturing behavior may be more prevalent in settings with thick GHSZs.« less

Schiaparelli Sedimentary Rocks

NASA Technical Reports Server (NTRS)

2003-01-01

MGS MOC Release No. MOC2-403, 26 June 2003

Some of the most important high resolution imaging results of the Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) experiment center on discoveries about the presence and nature of the sedimentary rock record on Mars. This old meteor impact crater in northwestern Schiaparelli Basin exhibits a spectacular view of layered, sedimentary rock. The 2.3 kilometer (1.4 miles) wide crater may have once been completely filled with sediment; the material was later eroded to its present form. Dozens of layers of similar thickness and physical properties are now expressed in a wedding cake-like stack in the middle of the crater. Sunlight illuminating the scene from the left shows that the circle, or mesa top, at the middle of the crater stands higher than the other stair-stepped layers. The uniform physical properties and bedding of these layers might indicate that they were originally deposited in a lake (it is possible that the crater was at the bottom of a much larger lake, filling Schiaparelli Basin); alternatively, the layers were deposited by settling out of the atmosphere in a dry environment. This picture was acquired on June 3, 2003, and is located near 0.9oS, 346.2oW.

Replication of Annual Cycles in Mn in Hudson River Cores: Mn Peaks During High Water Flow

NASA Astrophysics Data System (ADS)

Abbott, D. H.; Hutson, D.; Marrero, A. M.; Block, K. A.; Chang, C.; Cai, Y.

2017-12-01

Using the results from an ITRAX, XRF scanner, we previously reported apparent annual cycles in Mn in a single, high sedimentation rate Hudson River core, LWB1-8, taken off Yonkers, NY (Carlson et al., 2016). We replicated these results in three more high sedimentation rate cores and found stratigraphic markers that verify our inferences about the annual nature of the Mn cycles. The three new cores are LWB4-5 taken off Peekskill, NY, and LWB3-44 and LWB3-25, both taken in Haverstraw Bay. The cores are from water depths of 7-9 meters and all have high magnetic susceptibilities (typically > 30 cgs units) in their upper 1 to 2 meters. The high susceptibilities are primarily produced by magnetite from modern industrial combustion. One core, LWB1-8, has reconnaissance Cs dates that verify the annual nature of the cycles. More Cs dates are expected before the meeting. We developed several new methods of verifying the annual nature of our layer counts. The first is looking at the grain size distribution and age of layers with unusually high Mn peaks. Peaks in Si, Ni and Ti and peaks in percentage of coarse material typically accompany the peaks in Mn. Some are visible as yellow sandy layers. The five highest peaks in Mn in LWB1-8 have layer counted ages that correspond (within 1 year in the top meter and within 2 years in the bottom meter) to 1996, 1948, 1913, 1857 and 1790. The latter three events are the three largest historical spring freshets on the Hudson. 1996 is a year of unusually high flow rate during the spring freshet. Based on our work and previous work on Mn cycling in rivers, we infer that the peaks in Mn are produced by extreme erosional events that erode sediment and release pore water Mn into the water column. The other methods of testing our chronology involve marine storms that increase Ca and Sr and a search for fragments of the Peekskill meteorite that fell in October 1992. More information on the latter will be available by the meeting.

Exploring Links Between Global Climate and Explosive Arc Volcanism in Tephra-Rich Quaternary Sediments: A Pilot Study from IODP Expedition 350 Site 1437B, Izu Bonin Rear-Arc Region

NASA Astrophysics Data System (ADS)

Corry-Saavedra, K.; Straub, S. M.; Bolge, L.; Schindlbeck, J. C.; Kutterolf, S.; Woodhead, J. D.

2015-12-01

Fallout tephra in marine sediment provide an excellent archive of explosive arc volcanism that can be directly related to the other parameters of climate change, such as ice volume data, IRD (ice-rafted debris) input, etc. Current studies are based on 'discrete' tephra beds, which are produced by major eruptions and visible with the naked eye. Yet the more common, but less explosive arc eruptions that are more continuous through time produce 'disperse' tephra, which is concealed by the non-volcanic host sediment and invisible to the eye. The proportion of disperse tephra in marine sediments is known to be significant and may be critical in elucidating potential synchronicity between arc volcanism and glacial cycles. We conducted a pilot study in young sediments of IODP Hole 1437B drilled at 31°47.3911'N and 139°01.5788'E at the rear-arc of the Izu Bonin volcanic arc. By means of δ18O (Vautravers, in revision), eleven climatic cycles are recorded in uppermost 120 meter of carbonate mud that is interspersed by cm-thick tephra fallout layers. We selected six tephra layers, ranging from 0.2 to 1.16 million years in age, and sampled those vertically, starting from carbonate mud below the basal contact throughout the typical gradational top into the carbonate mud above. From each tephra bed, volcanic particles (>125 micrometer) were handpicked. All other samples were powdered and leached in buffered acetic acid and hydroxylamine hydrochloride to remove the carbonate and authigenous fraction, respectively. Major and trace element abundances (except for SiO2) from all samples were determined by ICP-MS and ICP-OES methods. Strong binary mixing trends are revealed between the pure tephra end member, and detrital sediment component. The tephra is derived from the Izu Bonin volcanic front and rear-arc, while the sediment component is presumably transported by ocean surface currents from the East China Sea. Our data show that mixing proportions change systematically with sample percentage left after leaching and the stratigraphic position of sample, implying that the composition of the aluminosilicate fraction is an indicator of the percentage of disperse ash present in the carbonate mud. This data leave potential to investigate temporal trends. Our results are currently being refined with radiogenic isotope data.

A detailed Holocene glacial-periglacial reconstruction based on multidisciplinary studies of a 60 m permafrost core from central Svalbard

NASA Astrophysics Data System (ADS)

Hvidtfeldt Christiansen, Hanne; Elberling, Bo; Gilbert, Graham L.; Thiel, Christine; Murray, Andrew; Buylaert, Jan-Pieter; Dypvik, Henning; Lomstein, Bente; Hovgaard, Jonas; Christensen, Anne T.; Mørkved, Pål T.; Reigstad, Laila J.; Fromreide, Siren; Seidenkrantz, Marit-Solveig

2014-05-01

During summer 2012, a 60 m sedimentary permafrost core was retrieved from the lower part of the Adventdalen Valley, central Svalbard, as part of the Longyearbyen CO2 project. The core was taken in 3 m long sections, with 20 % core loss, and reached the sedimentary bedrock (Lower Cretaceous). Thus our samples had the potential to represent the entire Quaternary and reflect changes in the sedimentary environments through time. The stratigraphy and sedimentology of the core was first investigated, to establish an overall geological model for the sampling site. The general stratigraphy encompasses a layer of basal till at the bottom of the core. This is overlain by marine sediments documenting a transition from glacial-proximal to open-marine conditions. Subsequently, a thick package of deltaic sediments records the progradation of the local river system. Finally, aeolian sediments, characterizing the modern environment, form the top few meters of the core. The ice content of the permafrost is generally low. Gravimetric water content generally ranges between 20% and 40%, but is considerably higher in some ice-rich layers. High resolution optically stimulated luminescence dating of the core sediment shows that deposition was very fast and took place primarily during the mid Holocene, with very rapid sedimentation of around 4 m/ka. With the onset of aeolian deposition (around 3-4 ka) the sedimentation rate decreased significantly to 1m/ka. The microbial diversity and activity of the core are being studied displaying decreasing activity with depth. Microbial community and functional gene numbers indicate variations with depth and geochemistry. Incubation studies have been performed primarily on the upper 30 m, and indicate a potential CO2 production from all depth intervals being studied. The potential for using foraminifer studies for both dating and palaeoenvironmental reconstructions are evaluated with the intension of comparison with previous studies of marine sediment cores both from the fjords in the Svalbard area and from the Barents Sea and Fram Strait region. This multidisciplinary approach is allowing us to build the first detailed palaeoenvironmental reconstruction of the Holocene glacial-periglacial interaction in the lowlands of central Svalbard; this includes a detailed reconstruction of the permafrost conditions.

Increased Power in Sediment Microbial Fuel Cell: Facilitated Mass Transfer via a Water-Layer Anode Embedded in Sediment.

PubMed

Lee, Yoo Seok; An, Junyeong; Kim, Bongkyu; Park, HyunJun; Kim, Jisu; Chang, In Seop

2015-01-01

We report a methodology for enhancing the mass transfer at the anode electrode of sediment microbial fuel cells (SMFCs), by employing a fabric baffle to create a separate water-layer for installing the anode electrode in sediment. The maximum power in an SMFC with the anode installed in the separate water-layer (SMFC-wFB) was improved by factor of 6.6 compared to an SMFC having the anode embedded in the sediment (SMFC-woFB). The maximum current density in the SMFC-wFB was also 3.9 times higher (220.46 mA/m2) than for the SMFC-woFB. We found that the increased performance in the SMFC-wFB was due to the improved mass transfer rate of organic matter obtained by employing the water-layer during anode installation in the sediment layer. Acetate injection tests revealed that the SMFC-wFB could be applied to natural water bodies in which there is frequent organic contamination, based on the acetate flux from the cathode to the anode.

Influence of sediment recycling on the trace element composition of primitive arc lavas

NASA Astrophysics Data System (ADS)

Collinet, M.; Jagoutz, O. E.

2017-12-01

Primitive calc-alkaline lavas from continental arcs are, on average, enriched in incompatible elements compared to those from intra-oceanic arcs. This relative enrichment is observed in different groups of trace elements: LILE (e.g. K, Rb), LREE to MREE (La-Dy) and HFSE (e.g.Zr, Nb) and is thought to result from (1) a transfer of material from the subducting slab to the mantle wedge at higher temperature than in intra-oceanic margins and/or (2) lower average degrees of melting in the mantle wedge, as a consequence of thicker overlying crusts and higher average pressures of melting. In addition to thicker overlying crusts and generally higher slab temperatures, continental margins are characterized by larger volumes of rock exposed above sea level and enhanced erosion rates compared to intra-oceanic arcs. As several geochemical signatures of arc lavas attest to the importance of sediment recycling in subduction zones, we explore the possibility that the high concentrations of incompatible elements in primitive lavas from continental arcs directly reflect a larger input of sediment to the subduction system. Previous efforts to quantify the sediment flux to oceanic trenches focused on the thickness of pelagic and hemipelagic sediments on top of the plate entering the subduction zone (Plank and Langmuir, 1993, Nature). These estimates primarily relied on the sediment layer drilled outboard from the subduction system and likely underestimate the volume of sediment derived from the arc itself. Accordingly, we find that such estimates of sediment flux do not correlate with the concentration of incompatible elements in primitive arc lavas. To account for regional contributions of coarser detrital sediments, usually delivered to oceanic trenches by turbidity currents, we apply to arc segments a model that quantifies the sediment load of rivers based on the average relief, area, temperature and runoff of their respective drainage areas (Syvitski et al., 2003, Sediment. Geol.). Our new estimates of sediment fluxes correlate positively with incompatible element concentrations in primitive arc lavas. We conclude that a large fraction of the local terrigenous sediments is subducted and contributes to the observed dichotomy in the trace element budget between primitive lavas from continental and oceanic margins.

Characteristics of the near-bottom suspended sediment field over the continental shelf off northern California based on optical attenuation measurements during STRESS and SMILE

NASA Astrophysics Data System (ADS)

Trowbridge, J. H.; Butman, B.; Limeburner, R.

1994-08-01

Time-series measurements of current velocity, optical attenuation and surface wave intensity obtained during the Sediment Transport Events on Shelves and Slopes (STRESS) experiments, combined with shipboard measurements of conductivity, temperature and optical attenuation obtained during the Shelf Mixed Layer Experiment (SMILE), provide a description of the sediment concentration field over the central and outer shelf off northern California. The questions addressed are: (1) existence and characteristics of bottom nepheloid layers and their relationship to bottom mixed layers; (2) characteristics of temporal fluctuations in sediment concentration and their relationship to waves and currents; (3) spatial scales over which suspended sediment concentrations vary horizontally; and (4) vertical distribution of suspended sediment.

Cloud layer thicknesses from a combination of surface and upper-air observations

NASA Technical Reports Server (NTRS)

Poore, Kirk D.; Wang, Junhong; Rossow, William B.

1995-01-01

Cloud layer thicknesses are derived from base and top altitudes by combining 14 years (1975-1988) of surface and upper-air observations at 63 sites in the Northern Hemisphere. Rawinsonde observations are employed to determine the locations of cloud-layer top and base by testing for dewpoint temperature depressions below some threshold value. Surface observations serve as quality checks on the rawinsonde-determined cloud properties and provide cloud amount and cloud-type information. The dataset provides layer-cloud amount, cloud type, high, middle, or low height classes, cloud-top heights, base heights and layer thicknesses, covering a range of latitudes from 0 deg to 80 deg N. All data comes from land sites: 34 are located in continental interiors, 14 are near coasts, and 15 are on islands. The uncertainties in the derived cloud properties are discussed. For clouds classified by low-, mid-, and high-top altitudes, there are strong latitudinal and seasonal variations in the layer thickness only for high clouds. High-cloud layer thickness increases with latitude and exhibits different seasonal variations in different latitude zones: in summer, high-cloud layer thickness is a maximum in the Tropics but a minimum at high latitudes. For clouds classified into three types by base altitude or into six standard morphological types, latitudinal and seasonal variations in layer thickness are very small. The thickness of the clear surface layer decreases with latitude and reaches a summer minimum in the Tropics and summer maximum at higher latitudes over land, but does not vary much over the ocean. Tropical clouds occur in three base-altitude groups and the layer thickness of each group increases linearly with top altitude. Extratropical clouds exhibit two groups, one with layer thickness proportional to their cloud-top altitude and one with small (less than or equal to 1000 m) layer thickness independent of cloud-top altitude.

Something Old, Something New

NASA Technical Reports Server (NTRS)

2006-01-01

20 September 2006 When it was launched in 1996, the plan was that Mars Global Surveyor (MGS) would wrap up its mission in 2000. Damage to a hinge connected to a solar panel slowed the orbit insertion aerobraking process by a year, so in 1997 the spacecraft team determined that MGS's mission would end in early 2001. However, the spacecraft and its instruments remained healthy, and its mission was extended. And extended. And extended again. And again. MGS has now been orbiting the red planet for just over nine years. Throughout the mission, data from the Mars Orbiter Camera (MOC) have emphasized details about some of the very oldest and the very newest features exposed on the planet's surface.

The very ancient and the modern come together in this small, approximately 3 km by 3 km (1.9 mi by 1.9 mi) area on the floor of an unnamed impact crater in western Arabia Terra.

Old are the light-toned, layered mounds scattered across the image. The layers form stair-steps leading to the top of each mound. In most cases, the 'steps' are not clean, but are instead covered with debris eroded from the next layer, or step, above. The mounds are remnants of layered rock that once covered the entire scene. They were deposited as sediment in the large, unnamed crater in which these landforms occur. Their regular thickness and repeated character suggest that episodic, or perhaps cyclic, processes brought sediment to the crater floor. If the crater contained water at the time the sediments were deposited, then they represent lakebed materials. The processes that (a) brought sediment to this site, (b) cemented the sediment to form rock, and (c) eroded the sediment to form the mounds we see today, all occurred at some time in the distant past.

New are the dark-toned sand dunes and intermediate-toned ripples. The dark dunes were formed of sand that in relatively recent times has been blown by wind from the northeast (upper right) toward the southwest (lower left). The dunes have slowly encroached upon the older, light-toned, layered mounds. Surrounding each mound is a suite of intermediate-toned ripples. These are large ripples, relative to counterparts on Earth, and are most likely made up of grains somewhat coarser than sand, typically of several millimeters in size. The ripples form a pattern that is generally radial to each mound, indicating that they formed in winds that interacted with these topographic obstacles. The dark dunes are generally younger than the ripples, as dark sand has encroached upon and over-ridden some of the ripples.

This image is one of the favorites of the MOC operations team at Malin Space Science Systems, because it is not only pretty, it also emphasizes aspects of both the ancient and modern sedimentary processes and materials on Mars. Sediments, sedimentary rocks, and the environments in which they were deposited have been a key theme of the MOC science investigation from the beginning, more than 20 years ago, when MOC was selected by NASA to be built and sent to Mars. The first MOC was aboard Mars Observer when it was lost in 1993; the second MOC was built for MGS and is still operating today.

Location near: 8.8oN, 1.2oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Winter

Numerical simulations of sand production in interbedded hydrate-bearing sediments during depressurization

USGS Publications Warehouse

Uchida, Shun; Lin, Jeen-Shang; Myshakin, Evgeniy; Seol, Yongkoo; Collett, Timothy S.; Boswell, Ray

2017-01-01

Geomechanical behavior of hydrate-bearing sediments during gas production is complex, involving changes in hydrate-dependent mechanical properties. When interbedded clay layers are present, the complexity is more pronounced because hydrate dissociation tends to occur preferentially in the sediments adjacent to the clay layers due to clay layers acting as a heat source. This would potentially lead to shearing deformation along the sand/clay contacts and may contribute to solid migration, which hindered past field-scale gas production tests. This paper presents a near-wellbore simulation of sand/clay interbedded hydrate-bearing sediments that have been subjected to depressurization and discusses the effect of clay layers on sand production.

Light emitting ceramic device

DOEpatents

Valentine, Paul; Edwards, Doreen D.; Walker, Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

2010-05-18

A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, is herein claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

Exploring microphysical, radiative, dynamic and thermodynamic processes driving fog and low stratus clouds using ground-based Lidar and Radar measurements

NASA Astrophysics Data System (ADS)

Haeffelin, Martial

2016-04-01

Radiation fog formation is largely influenced by the chemical composition, size and number concentration of cloud condensation nuclei and by heating/cooling and drying/moistening processes in a shallow mixing layer near the surface. Once a fog water layer is formed, its development and dissipation become predominantly controlled by radiative cooling/heating, turbulent mixing, sedimentation and deposition. Key processes occur in the atmospheric surface layer, directly in contact with the soil and vegetation, and throughout the atmospheric column. Recent publications provide detailed descriptions of these processes for idealized cases using very high-resolution models and proper representation of microphysical processes. Studying these processes in real fog situations require atmospheric profiling capabilities to monitor the temporal evolution of key parameters at several heights (surface, inside the fog, fog top, free troposphere). This could be done with in-situ sensors flown on tethered balloons or drones, during dedicated intensive field campaigns. In addition Backscatter Lidars, Doppler Lidars, Microwave Radiometers and Cloud Doppler Radars can provide more continuous, yet precise monitoring of key parameters throughout the fog life cycle. The presentation will describe how Backscatter Lidars can be used to study the height and kinetics of aerosol activation into fog droplets. Next we will show the potential of Cloud Doppler Radar measurements to characterize the temporal evolution of droplet size, liquid water content, sedimentation and deposition. Contributions from Doppler Lidars and Microwave Radiometers will be discussed. This presentation will conclude on the potential to use Lidar and Radar remote sensing measurements to support operational fog nowcasting.

Holocene Depositional History of Shad Pond, a Hypersaline Coastal Lagoon, Eleuthera, Bahamas and Its Influence on Lucayan Occupation

NASA Astrophysics Data System (ADS)

Boush, L. E.; Fentress, S.; Conroy, M.; Cook, A.; Miseridina, D.; Buynevich, I. V.; Myrbo, A.; Brown, E. T.; Berman, M.; Gnivecki, P.; Kjellmark, E.; Savarese, M.; Brady, K.

2013-12-01

Shad Pond, an enclosed hypersaline lagoon on the southeastern tip of Eleuthera, Bahamas reveals a ~5000-year record of hurricane activity, as well as sea-level and climate change history. Three sediment cores recovered 1.04-2.54 m of sediment over bedrock along a transect perpendicular to shoreline. Sediment composition and grain size, loss on ignition, X-ray fluorescence (XRF) measurements of the cores along with dune transects and ground-penetrating radar (GPR) profiles adjacent to the lake provide a comprehensive dataset to interpret the history of this coastal basin. The sedimentary sequence was composed of alternating lithofacies that included microbial mats, sand, and peat. Laminated mats often alternated with sandy layers in thin to medium-bedded units. Two peat layers were found in the basal part of the shore-distal core (Site 1) between 1.82-2.40 m and 2.53-2.54 m and were separated by a 13-cm-thick gray mud layer. In general, organic matter and carbonate content tracked granulometry and composition in all cores. High-resolution XRF scans of Ca and Sr at Site 1 show elevated levels ~3,700 cal yBP, which correlate with the top of the peat layer, but these elemental concentrations vary at Site 3. XRF measurements of Fe indicate a dust flux that has been recorded regionally throughout the Caribbean. Dune transects and GPR profiles indicate a phased history of the pond, beginning with initial stages as an open lagoon dominated by red mangrove, with black mangrove and buttonwood also present. The lake likely closed at approximately 3,700 cal yBP indicated by the transition between the upper peat and microbial mat layers. This could have been due to increased storm events in a regime of rising sea level. Aeolian aggradation continued to heighten the barrier between the bedrock headlands to its present position. Hurricane overwash deposits punctuated the algal mat accumulation throughout this time period. Present-day hypersaline conditions sustain algal mats throughout the lake bottom. It is likely that the occupation by Lucayan culture was influenced by the position of the shoreline along southern Eleuthera and this lake was already unsuitable as a water source at the time of their arrival and occupation during 1300-600 years BP (AD 700-1400).

Sedimentary records of Typhoon Haiyan in the South China Sea

NASA Astrophysics Data System (ADS)

Su, C. C.; Chen, Y. H.; Chang, J. H.; Hsu, H. H.; Yu, P. S.; Liu, C. S.

2016-12-01

South China Sea (SCS), which is located at the boundary of the Eurasian, Philippine Sea, and Indian plates, is the largest marginal sea of the northwest Pacific and also on the North Western Pacific corridor of typhoons. The unique tectonic setting and climatic conditions make it has to face the severe natural hazards, like submarine landslides, and high sediment discharges which induced by typhoon. On November 8, 2013, the Typhoon Haiyan, which was one of the largest tropical cyclones ever recorded in western Pacific, devastated Philippines and caused catastrophic destruction. Before the Typhoon Haiyan reached Hainan Province, China and Quangninh Province, Vietnam, it emerged over the SCS. How was the large amount of terrestrial materials distributed and recorded in deep sea sediments by such intense typhoon? Is it possible for us to reconstruct the history of extreme tropical cyclones by using deep sea cores? In this study, twelve gravity cores were collected in the Central SCS Basin and around Taiping Island (Itu Aba Island) from 2014 to 2015 and a series of analysis including Multi-Sensor Core Logger, XRF Core Scanner, core surface and X-radiograph images, grain size, and excess 210Pb chronology were conducted for modern extreme event records in cores and attempt to evaluate the possibility of reconstructed extreme typhoon records in cores from the SCS. On core surface images, an obvious brownish oxidized layer exist in core top with higher 210Pb activities beneath the layer. According to the sampling time, we conjecture the oxidized layer might formed by Typhoon Haiyan in 2013. In addition, the Itrax data shows high manganese content only exist in this layer which might related to the modern industrial pollution delivered by typhoon induced flooding from Philippines. The Power Barge 103 of Napocor in Estancia IIoilo was dislodged from its mount by Typhoon Haiyan and the United Nations Disaster Assessment and Coordination Team reported 600,000 liters of bunker fuel had spilled. To clarify the relationship between the oil spill and high manganese records in sediments, some further analysis is needed. Our analysis result shows, in the Central SCS Basin, over 80 cm turbidite layer was deposited by Typhoon Haiyan and it will take more than 4000 years to deposit on seafloor without the impact of extreme events.

Sedimentary chronology reinterpreted from Changshou Lake of the Three Gorges Reservoir Area reveals natural and anthropogenic controls on sediment production.

PubMed

Anjum, Raheel; Tang, Qiang; Collins, Adrian L; Gao, Jinzhang; Long, Yi; Zhang, Xinbao; He, Xiubin; Shi, Zhonglin; Wen, Anbang; Wei, Jie

2018-04-17

Sedimentary archives preserved in geomorphic sinks provide records of historical sediment dynamics and its related natural and anthropogenic controls. This study reinterpreted sedimentary processes in Changshou Lake of the Three Gorges Reservoir Area in China by combining a rainfall erosivity index with multiple tracing proxies, and the impacts of natural and anthropogenic drivers on sediment production were also explored. Erosive rainfalls with low frequency and large magnitude in the rainy season contribute to a substantial proportion of annual total rainfall, which thus can be used to infer erosion and sediment yield events. The sedimentary chronology was determined by comparing rainfall erosivity index with depth distribution of 137 Cs and absolute particle size, which revealed annual sedimentation rates ranging from 1.1 to 2.3 cm a -1 . The multi-proxy dating index and variation of sedimentation rate divided the sediment profile into three major periods. The reference period (1956-1982) displays low variability of TOC, TN, trace metal concentrations, and mean sedimentation rate. In the stressed period (1982-1998), industrial and sewerage discharge led to input and deposition of TOC, TN, and trace metals (e.g., Cd, Co, Cu, Cr, and Ni). The highest annual sediment accumulation rate of 2.3 cm a -1 may be ascribed to the 1982 big flood event. In the present period (1998-2013), increased TOC, TN and decreased trace metals in the top layers of the sediment core indicated changes in lake ecology. Fish farming promoted algal growth and primary productivity which caused eutrophication until 2004-2005. The reduced mean sedimentation rate of 1.7 cm a -1 between 1998 and 2004, and thereafter, may be attributed to soil and water conservation and reforestation policies implemented in the Longxi catchment. Human activities such as deforestation, cultural and industrial revolution, and lake eutrophication associated with fish farming since 1989, therefore led to appreciable limnological variations. Overall, the dated sedimentary profile from Changshou Lake displays high consistency with archived historical events and reflects the impact of both natural and anthropogenic controls on sediment production.

Apulian crust: Top to bottom

NASA Astrophysics Data System (ADS)

Amato, Alessandro; Bianchi, Irene; Agostinetti, Nicola Piana

2014-12-01

We investigate the crustal seismic structure of the Adria plate using teleseismic receiver functions (RF) recorded at 12 broadband seismic stations in the Apulia region. Detailed models of the Apulian crust, e.g. the structure of the Apulian Multi-layer Platform (AMP), are crucial for assessing the presence of potential décollements at different depth levels that may play a role in the evolution of the Apenninic orogen. We reconstruct S-wave velocity profiles applying a trans-dimensional Monte Carlo method for the inversion of RF data. Using this method, the resolution at the different depth level is completely dictated by the data and we avoid introducing artifacts in the crustal structure. We focus our study on three different key-elements: the Moho depth, the lower crust S-velocity, and the fine-structure of the AMP. We find a well defined and relatively flat Moho discontinuity below the region at 28-32 km depth, possibly indicating that the original Moho is still preserved in the area. The lower crust appears as a generally low velocity layer (average Vs = 3.7 km/s in the 15-26 km depth interval), likely suggestive of a felsic composition, with no significant velocity discontinuities except for its upper and lower boundaries where we find layering. Finally, for the shallow structure, the comparison of RF results with deep well stratigraphic and sonic log data allowed us to constrain the structure of the AMP and the presence of underlying Permo-Triassic (P-T) sediments. We find that the AMP structure displays small-scale heterogeneities in the region, with a thickness of the carbonates layers varying between 4 and 12 km, and is underlain by a thin, discontinuous layer of P-T terrigenous sediments, that are lacking in some areas. This fact may be due to the roughness in the original topography of the continental margins or to heterogeneities in its shallow structure due to the rifting process.

The occurrence of extreme events a tsunami and storm deposit in Chilcatay formation, Ica, Peru.

NASA Astrophysics Data System (ADS)

Poma Porras, O. A.; Cayo, R., Jr.; Casas, N.; Figueroa, F.

2016-12-01

The Chilcatay Formation (Oligocene to middle Miocene) south of Peru is in the Pisco Basin contains a thick sequence of Cenozoic sediments that record at least three marine transgressions characterized by successions of fine sandstones, siltstones, and diatomaceous mudstones. The sequence records certain facies that are typical of high-energy events, including extreme storms, tsunamis and earthquakes. The studied deposit is characterized by the presence of two layers of varying thickness. The lower layer, which is in markedly erosive contact with the underlying layer, is a very coarse-grained sandstone, highly sorted and with subrounded to subangular grains. The thickness varies laterally from one to 50 cm. The top layer, which is 40-60 cm thick and exposed for approximately 200 m, consists of a dense matrix of coarse-grained size fragments of molluscs (oysters), barnacles, and lithoclasts. The biogenic matrix contains many igneous (gabbro, granite) and metamorphic cobbles and boulders, and lithic tuffs, clusters of barnacles, and fragments consisting of vermetid gastropods reefs. The abundant igneous and metamorphic cobbles and boulders are rounded and subrounded, with a larger diameter between 3 and 140 cm, and occurring at a density of 3-8 clasts by square meter. The lithic tuffs are subrounded, have an ovoid morphology and a greater diameter between 1 and 44 cm. All these clasts occur scattered and 'floating' in the bioclastic matrix. The characteristics of the studied layer suggest that it was deposited by an extreme event that eroded the area between shoreface and backshore redepositing the materials and leaving a chaotic facies distribution with cobbles and boulders of different lithology. The large waves caused heavy erosion of the sediments in the shallow seafloor and the basement, mixing the biogenic and lithogenic clasts. The large size of these clasts suggests that such an event may have been a tsunami.

Impacts of solar-absorbing aerosol layers on the transition of stratocumulus to trade cumulus clouds

DOE PAGES

Zhou, Xiaoli; Ackerman, Andrew S.; Fridlind, Ann M.; ...

2017-10-26

Here, the effects of an initially overlying layer of solar-absorbing aerosol on the transition of stratocumulus to trade cumulus clouds are examined using large-eddy simulations. For lightly drizzling cloud the transition is generally hastened, resulting mainly from increased cloud droplet number concentration ( N c) induced by entrained aerosol. The increased N c slows sedimentation of cloud droplets and shortens their relaxation time for diffusional growth, both of which accelerate entrainment of overlying air and thereby stratocumulus breakup. However, the decrease in albedo from cloud breakup is more than offset by redistributing cloud water over a greater number of droplets,more » such that the diurnal-average shortwave forcing at the top of the atmosphere is negative. The negative radiative forcing is enhanced by sizable longwave contributions, which result from the greater cloud breakup and a reduced boundary layer height associated with aerosol heating. A perturbation of moisture instead of aerosol aloft leads to a greater liquid water path and a more gradual transition. Adding absorbing aerosol to that atmosphere results in substantial reductions in liquid water path (LWP) and cloud cover that lead to positive shortwave and negative longwave forcings on average canceling each other. Only for heavily drizzling clouds is the breakup delayed, as inhibition of precipitation overcomes cloud water loss from enhanced entrainment. Considering these simulations as an imperfect proxy for biomass burning plumes influencing Namibian stratocumulus, we expect regional indirect plus semi-direct forcings to be substantially negative to negligible at the top of the atmosphere, with its magnitude sensitive to background and perturbation properties.« less

Impacts of solar-absorbing aerosol layers on the transition of stratocumulus to trade cumulus clouds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Xiaoli; Ackerman, Andrew S.; Fridlind, Ann M.

Here, the effects of an initially overlying layer of solar-absorbing aerosol on the transition of stratocumulus to trade cumulus clouds are examined using large-eddy simulations. For lightly drizzling cloud the transition is generally hastened, resulting mainly from increased cloud droplet number concentration ( N c) induced by entrained aerosol. The increased N c slows sedimentation of cloud droplets and shortens their relaxation time for diffusional growth, both of which accelerate entrainment of overlying air and thereby stratocumulus breakup. However, the decrease in albedo from cloud breakup is more than offset by redistributing cloud water over a greater number of droplets,more » such that the diurnal-average shortwave forcing at the top of the atmosphere is negative. The negative radiative forcing is enhanced by sizable longwave contributions, which result from the greater cloud breakup and a reduced boundary layer height associated with aerosol heating. A perturbation of moisture instead of aerosol aloft leads to a greater liquid water path and a more gradual transition. Adding absorbing aerosol to that atmosphere results in substantial reductions in liquid water path (LWP) and cloud cover that lead to positive shortwave and negative longwave forcings on average canceling each other. Only for heavily drizzling clouds is the breakup delayed, as inhibition of precipitation overcomes cloud water loss from enhanced entrainment. Considering these simulations as an imperfect proxy for biomass burning plumes influencing Namibian stratocumulus, we expect regional indirect plus semi-direct forcings to be substantially negative to negligible at the top of the atmosphere, with its magnitude sensitive to background and perturbation properties.« less

Impacts of solar-absorbing aerosol layers on the transition of stratocumulus to trade cumulus clouds

NASA Astrophysics Data System (ADS)

Zhou, Xiaoli; Ackerman, Andrew S.; Fridlind, Ann M.; Wood, Robert; Kollias, Pavlos

2017-10-01

The effects of an initially overlying layer of solar-absorbing aerosol on the transition of stratocumulus to trade cumulus clouds are examined using large-eddy simulations. For lightly drizzling cloud the transition is generally hastened, resulting mainly from increased cloud droplet number concentration (Nc) induced by entrained aerosol. The increased Nc slows sedimentation of cloud droplets and shortens their relaxation time for diffusional growth, both of which accelerate entrainment of overlying air and thereby stratocumulus breakup. However, the decrease in albedo from cloud breakup is more than offset by redistributing cloud water over a greater number of droplets, such that the diurnal-average shortwave forcing at the top of the atmosphere is negative. The negative radiative forcing is enhanced by sizable longwave contributions, which result from the greater cloud breakup and a reduced boundary layer height associated with aerosol heating. A perturbation of moisture instead of aerosol aloft leads to a greater liquid water path and a more gradual transition. Adding absorbing aerosol to that atmosphere results in substantial reductions in liquid water path (LWP) and cloud cover that lead to positive shortwave and negative longwave forcings on average canceling each other. Only for heavily drizzling clouds is the breakup delayed, as inhibition of precipitation overcomes cloud water loss from enhanced entrainment. Considering these simulations as an imperfect proxy for biomass burning plumes influencing Namibian stratocumulus, we expect regional indirect plus semi-direct forcings to be substantially negative to negligible at the top of the atmosphere, with its magnitude sensitive to background and perturbation properties.

Impacts of Solar-Absorbing Aerosol Layers on the Transition of Stratocumulus to Trade Cumulus Clouds

NASA Technical Reports Server (NTRS)

Zhou, Xiaoli; Ackerman, Andrew S.; Fridlind, Ann M.; Wood, Robert; Kollias, Pavlos

2017-01-01

The effects of an initially overlying layer of solar-absorbing aerosol on the transition of stratocumulus to trade cumulus clouds are examined using large-eddy simulations. For lightly drizzling cloud the transition is generally hastened, resulting mainly from increased cloud droplet number concentration (Nc) induced by entrained aerosol. The increased Nc slows sedimentation of cloud droplets and shortens their relaxation time for diffusional growth, both of which accelerate entrainment of overlying air and thereby stratocumulus breakup. However, the decrease in albedo from cloud breakup is more than offset by redistributing cloud water over a greater number of droplets, such that the diurnal-average shortwave forcing at the top of the atmosphere is negative. The negative radiative forcing is enhanced by sizable longwave contributions, which result from the greater cloud breakup and a reduced boundary layer height associated with aerosol heating. A perturbation of moisture instead of aerosol aloft leads to a greater liquid water path and a more gradual transition. Adding absorbing aerosol to that atmosphere results in substantial reductions in liquid water path (LWP) and cloud cover that lead to positive short-wave and negative longwave forcings on average canceling each other. Only for heavily drizzling clouds is the breakup delayed, as inhibition of precipitation overcomes cloud water loss from enhanced entrainment. Considering these simulations as an imperfect proxy for biomass burning plumes influencing Namibian stratocumulus, we expect regional indirect plus semi-direct forcings to be substantially negative to negligible at the top of the atmosphere, with its magnitude sensitive to background and perturbation properties.

Hydrocarbon pollution in the sediment from the Jarzouna-Bizerte coastal area of Tunisia (Mediterranean Sea).

PubMed

Zrafi-Nouira, I; Khedir-Ghenim, Z; Zrafi, F; Bahri, R; Cheraeif, I; Rouabhia, M; Saidane-Mosbahi, D

2008-06-01

This study investigated the presence and origin of hydrocarbon pollution in industrial waste water sediments found near the Jarzouna (Bizerte, Tunisia) oil refinery. Analyses of surface sediments (layer 1) and deep sediments (layer 2) showed that Total Hydrocarbon (TH) concentrations ranged from 602 +/- 7.638 microg/g in layer-1 to 1270 +/- 2.176 microg/g in layer-2. The results suggest that the deeper the sediment, the higher the level of total hydrocarbon found. The sedimentary Non Aromatic Hydrocarbon (NAH) and Aromatic Hydrocarbon (AH) concentrations ranged from 66.22 +/- 1.516 to 211.82 +/- 10.670 microg/g for NAH, and from 13.84 +/- 0.180 to 115.60 +/- 2.479 microg/g for AH. The high variability of these concentrations was associated with the location of the sediment collection sites. Aliphatic biomarker analysis revealed petroleum contamination close to the refinery rejection site, and biogenic sources further away. Petroleum contamination may be associated with increased industrial activity in the area of Jarzouna-Bizerte in the Mediterranean Sea.

Polygonal deformation bands in sandstone

NASA Astrophysics Data System (ADS)

Antonellini, Marco; Nella Mollema, Pauline

2017-04-01

We report for the first time the occurrence of polygonal faults in sandstone, which is compelling given that layer-bound polygonal fault systems have been observed so far only in fine-grained sediments such as clay and chalk. The polygonal faults are dm-wide zones of shear deformation bands that developed under shallow burial conditions in the lower portion of the Jurassic Entrada Fm (Utah, USA). The edges of the polygons are 1 to 5 meters long. The shear deformation bands are organized as conjugate faults along each edge of the polygon and form characteristic horst-like structures. The individual deformation bands have slip magnitudes ranging from a few mm to 1.5 cm; the cumulative average slip magnitude in a zone is up to 10 cm. The deformation bands heaves, in aggregate form, accommodate a small isotropic horizontal extension (strain < 0.005). The individual shear deformation bands show abutting T-junctions, veering, curving, and merging where they mechanically interact. Crosscutting relationships are rare. The interactions of the deformation bands are similar to those of mode I opening fractures. Density inversion, that takes place where under-compacted and over-pressurized layers (Carmel Fm) lay below normally compacted sediments (Entrada Sandstone), may be an important process for polygonal deformation bands formation. The gravitational sliding and soft sediment structures typically observed within the Carmel Fm support this hypothesis. Soft sediment deformation may induce polygonal faulting in the section of the Entrada Sandstone just above the Carmel Fm. The permeability of the polygonal deformation bands is approximately 10-14 to 10-13 m2, which is less than the permeability of the host, Entrada Sandstone (range 10-12 to 10-11 m2). The documented fault networks have important implications for evaluating the geometry of km-scale polygonal fault systems in the subsurface, top seal integrity, as well as constraining paleo-tectonic stress regimes.

Atomic-Level Properties of Thermal Barrier Coatings: Characterization of Metal-Ceramic Interfaces

DTIC Science & Technology

2001-01-01

these cases metal - metal bonds were stronger than metal - substrate bonds, thus predicting a 3D (cluster) growth mode as opposed to layer-by-layer...coat layer must be deposited. The top coat serves as the insulator and the bond coat mediates contact between the top coat and metal alloy substrate ...in thermomechanical properties between a YSZ top coat and a metal -alloy substrate is enough to require the introduction of an intermediate layer. This

EPA Office of Water (OW): Nutrient, Sediment, and Pathogens Water Impairments

EPA Pesticide Factsheets

National dataset consisting of a snapshot of 303(d) Listed Impaired Waters combined with Impaired Waters with TMDLs whose parent cause is Nutrients, Sediments, and Pathogens. The snapshot constitutes the top water impairments. The Impaired Waters with TMDLs and the 303(d) Listed Impaired Waters are combined into three mapping service layers in MyWaters Mapper application to provide a comprehensive view of each of these impairments. These waters are linked to the 303(d) information stored in EPAs Assessment and TMDL Tracking and Implementation System (ATTAINS). Below is a brief description of the two programs.The 303(d) Listed Impaired Waters program system provides impaired water data and impaired water features reflecting river segments, lakes, and estuaries designated under Section 303(d) of the Clean Water Act. Each State will establish Total Maximum Daily Loads (TMDLs) for these waters. Note the CWA Section 303(d) list of impaired waters does not represent waters that are impaired but have an EPA-approved TMDL established, impaired waters for which other pollution control mechanisms are in place and expected to attain water quality standards, or waters impaired as a result of pollution and is not caused by a pollutant; therefore, the Impaired Waters layers do not represent all impaired waters reported in a state's Integrated Report, but only the waters comprised of a state's approved 303(d) list. For more information regarding impaired waters refer to EPA's

Solar modulation of flood frequency in Central Europe during spring and summer on inter-annual to millennial time-scales

NASA Astrophysics Data System (ADS)

Czymzik, M.; Muscheler, R.; Brauer, A.

2015-10-01

Solar influences on climate variability are one of the most controversially discussed topics in climate research. We analyze solar forcing of flood frequency in Central Europe on inter-annual to millennial time-scales using daily discharge data of River Ammer (southern Germany) back to AD 1926 and revisiting the 5500 year flood layer time-series from varved sediments of the downstream Lake Ammersee. Flood frequency in the discharge record is significantly correlated to changes in solar activity during solar cycles 16-23 (r = -0.47, p < 0.0001, n = 73). Flood layer frequency (n = 1501) in the sediment record depicts distinct multi-decadal variability and significant correlations to 10Be fluxes from a Greenland ice core (r = 0.45, p < 0.0001) and 14C production rates (r =0.36, p < 0.0001), proxy records of solar activity. Flood frequency is higher when solar activity is reduced. These correlations between flood frequency and solar activity might provide empirical support for the solar top-down mechanism expected to modify the mid-latitude storm tracks over Europe by model studies. A lag of flood frequency responses in the Ammer discharge record to changes in solar activity of about one to three years could be explained by a modelled ocean-atmosphere feedback delaying the atmospheric reaction to solar activity variations up to a few years.

Potentiometric Detection of Pathogens

DTIC Science & Technology

2012-01-01

nanosize organic electrode (conducting polymer top-layer) surface. This approach has then been changed to the gate modification in ion sensitive field...electrode (conducting polymer top-layer) surface. This approach has then been changed to the gate modification in ion sensitive field effect transistors, in...the conducting polymer top-layer, which makes the devices very functional and competitive. Secondly, the device development is discussed and finally

A Finite Element Procedure for Analysis of Laminated Composite Plates

DTIC Science & Technology

1991-06-18

71 14. X-stress at midsurface of the top layer with refinement in x- direction; Angle-ply specimen, using edge elements...72 15. X-stress at midsurface of top layer with thickness refinement; Angle- ply specimen ............................................ 73 16...XY-stress at midsurface of top layer with refinement in y-direction; Angle-ply specimen ........................................ 74 17. XY-stress at

A Finite Element Procedure for Analysis of Laminated Composite Plates

DTIC Science & Technology

1991-06-18

71 14. X-stress at midsurface of the top layer with refinement in x- direction; Angle-ply specimen, using edge elements...72 15. X-stress at midsurface of top layer with thickness refinement; Angle- ply specimen ............................................. 73 16. XY...stress at midsurface of top layer with refinement in y-direction; Angle-ply specimen ........................................ 74 17. XY-stress at

Geochemical effects of rapid sedimentation in aquatic systems: Minimal diagenesis and the preservation of historical metal signatures

USGS Publications Warehouse

Callender, E.

2000-01-01

Rapid sedimentation exerts a pronounced influence on early sedimentary diagenesis in that there is insufficient time for a sediment particle to equilibrate in any one sediment layer before that layer may be displaced vertically by another layer. These sedimentation patterns are common in surface-water reservoirs whose sedimentation rates (1-10 cm yr-1) are several orders of magnitude greater than those for natural lakes (0.01-0.5 cm yr-1). Two examples of the effects of rapid sedimentation on geochemical metal signatures are presented here. Interstitial-water data (Fe) from two sites in the Cheyenne River Embayment of Lake Oahe on the Missouri River illustrate the effects of changing sedimentation rates on dissolved species. Rapid burial during high-flow yrs appears to limit early sedimentary diagenesis to aerobic respiration. Solid-phase metal data (Pb) from a site in Pueblo Reservoir on the upper Arkansas River in Colorado appear to record historical releases by flooding of abandoned mine sites upstream in Leadville, Colorado. Interstitial-water ammonia and ferrous Fe data indicate that at least one interval at depth in the sediment where solid metal concentrations peak is a zone of minimal diagenesis. The principal diagenetic reactions that occur in these sediments are aerobic respiration and the reduction of Mn and Fe oxides. Under slower sedimentation conditions, there is sufficient time for particulate organic matter to decompose and create a diagenetic environment where metal oxides may not be stable. The quasi-steady-state interstitial Fe profiles from Tidal Potomac River sediments are an example of such a situation. This occurs primarily because the residence time of particles in the surficial sediment column is long enough to allow benthic organisms and bacteria to perform their metabolic functions. When faster sedimentation prevails, there is less time for these metabolic reactions to occur since the organisms do not occupy a sediment layer for any length of time. Also, the quantity and quality of the organic matter input to the sediment layer is important in that reservoirs often receive more terrestrial organic matter than natural lakes and this terrestrial organic matter is generally more refractory than autochthonous aquatic organic matter.

Year-Long Vertical Velocity Statistics Derived from Doppler Lidar Data for the Continental Convective Boundary Layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berg, Larry K.; Newsom, Rob K.; Turner, David D.

One year of Coherent Doppler Lidar (CDL) data collected at the U.S. Department of Energy’s Atmospheric Radiation Measurement (ARM) site in Oklahoma is analyzed to provide profiles of vertical velocity variance, skewness, and kurtosis for cases of cloud-free convective boundary layers. The variance was scaled by the Deardorff convective velocity scale, which was successful when the boundary layer depth was stationary but failed in situations when the layer was changing rapidly. In this study the data are sorted according to time of day, season, wind direction, surface shear stress, degree of instability, and wind shear across the boundary-layer top. Themore » normalized variance was found to have its peak value near a normalized height of 0.25. The magnitude of the variance changes with season, shear stress, and degree of instability, but was not impacted by wind shear across the boundary-layer top. The skewness was largest in the top half of the boundary layer (with the exception of wintertime conditions). The skewness was found to be a function of the season, shear stress, wind shear across the boundary-layer top, with larger amounts of shear leading to smaller values. Like skewness, the vertical profile of kurtosis followed a consistent pattern, with peak values near the boundary-layer top (also with the exception of wintertime data). The altitude of the peak values of kurtosis was found to be lower when there was a large amount of wind shear at the boundary-layer top.« less

Integration of the stratigraphic aspects of very large sea-floor databases using information processing

USGS Publications Warehouse

Jenkins, Clinton N.; Flocks, J.; Kulp, M.; ,

2006-01-01

Information-processing methods are described that integrate the stratigraphic aspects of large and diverse collections of sea-floor sample data. They efficiently convert common types of sea-floor data into database and GIS (geographical information system) tables, visual core logs, stratigraphic fence diagrams and sophisticated stratigraphic statistics. The input data are held in structured documents, essentially written core logs that are particularly efficient to create from raw input datasets. Techniques are described that permit efficient construction of regional databases consisting of hundreds of cores. The sedimentological observations in each core are located by their downhole depths (metres below sea floor - mbsf) and also by a verbal term that describes the sample 'situation' - a special fraction of the sediment or position in the core. The main processing creates a separate output event for each instance of top, bottom and situation, assigning top-base mbsf values from numeric or, where possible, from word-based relative locational information such as 'core catcher' in reference to sampler device, and recovery or penetration length. The processing outputs represent the sub-bottom as a sparse matrix of over 20 sediment properties of interest, such as grain size, porosity and colour. They can be plotted in a range of core-log programs including an in-built facility that better suits the requirements of sea-floor data. Finally, a suite of stratigraphic statistics are computed, including volumetric grades, overburdens, thicknesses and degrees of layering. ?? The Geological Society of London 2006.

Shallow velocity structure of the Alaska Peninsula subduction zone and implications for controls on seismic behavior

NASA Astrophysics Data System (ADS)

Li, J.; Shillington, D. J.; Becel, A.; Nedimovic, M. R.; Kuehn, H.; Webb, S. C.; Abers, G. A.; Keranen, K. M.; Saffer, D. M.

2014-12-01

Downdip and along-strike variations in the seismic behavior of subduction zone megathrust faults are thought to be strongly controlled by changes in the material properties along the plate boundary. Roughness and hydration of the incoming plate, fluid pressure and lithology in the subducting sediment channel are likely to control the distribution of shallower rupture. Here, we focus on the subduction zone offshore of the Alaska Peninsula. In 2011, the ALEUT program acquired deep penetration multichannel seismic (MCS) reflection and ocean bottom seismometer (OBS) data across the apparently freely sliding Shumagin Gap, the locked Semidi segment that last ruptured in 1938 M8.2 earthquake, and the locked western Kodiak asperity, which ruptured in the 1964 M9.2 earthquake. Seismic reflection data from the ALEUT cruise reveal significant variability in the thickness of sediment on the incoming plate and entering the trench, and the roughness and degree of hydration of the incoming plate. Oceanic crust entering the trench in the Shumagin gap is rugged with extensive faults and only a thin layer of sediment (<0.5 km thick). Farther east in the Semidi segment, the subducting plate has a smoother surface with thicker sediments (~1 km thick) and less faulting/hydration. To better constrain the properties of the accretionary prism and shallow part of the plate boundary, we are undertaking travel time tomography using reflection/refraction phases in OBS and MCS data, and constraints on the interface geometry from MCS images to estimate the detailed shallow velocity structure, with particular focus on properties within the shallow subduction channel. We observe refractions and reflections in OBS data from the shallow part of the subduction zone in both the Shumagin Gap and Semidi segment, including reflections off the top and base of what appears to be a layer of subducting sediment, which can be used for this work. We plan to present initial models of the shallow part of the subduction zone from both segments and discuss comparisons between the two.

Mid-term variation of vertical distribution of acid volatile sulphide and simultaneously extracted metals in sediment cores from Lake Albufera (Valencia, Spain).

PubMed

Hernández-Crespo, Carmen; Martín, Miguel

2013-11-01

Lake Albufera is one of the most eutrophic bodies of water in Spain due to point and diffuse pollution over past decades, and its sediments are likely to be anoxic because of high organic matter flux. Hence, sulphides can play an important role in limiting the mobility of heavy metals. This study aimed to study the vertical variation of acid volatile sulphide (AVS) and simultaneously extracted metals (SEM) in sediment cores collected from Lake Albufera; other sediment characteristics, such as organic matter, biochemical oxygen, demand or total metals, were also studied. Three sites were selected, and four sampling campaigns were performed to study spatial and temporal variation as well as to obtain information regarding historical variation in the composition of sediments. AVS and SEM were analysed by the purge-and-trap method. The vertical distribution of AVS and SEM varied depending on the sampling site-concentrations of AVS and SEM were higher at sites close to mouths of inflowing channels. A decreasing trend of AVS has been found at these sites over time: In the two first samplings, AVS increased with depth reaching maximum concentrations of 40 and 21 μmol g(-1), but from then on AVS were lower and decreased with depth. SEM decreased with depth from 3 μmol g(-1) in surface layers to approximately 1 μmol g(-1) at deeper segments at these sites. However, the central site was more uniform with respect to depth as well as with time; it presented lower values of SEM and AVS (mean 0.9 and 2.0 μmol g(-1) respectively), and the maximum value of AVS (7 μmol g(-1)) was found at the top layer (0-3 cm). According to the (SEM-AVS)/fOC approach, every site, and throughout the cores, can be classified as containing nontoxic metals because the values were <130 μmol g(-1).

Tulelake, California: The last 3 million years

USGS Publications Warehouse

Adam, D.P.; Sarna-Wojcicki, A. M.; Rieck, Hugh J.; Bradbury, J.P.; Dean, W.E.; Forester, R.M.

1989-01-01

The Tulelake basin, formed by east-west extension and faulting during the past several million years, contains at least 550 m of lacustrine sediment. Interdisciplinary studies of a 334 m-long cored section from the town of Tulelake, California, near the center of the basin, document a 3-m.y. record of environmental changes. The core consists of a thick sequence of diatomaceous clayey, silty, and marly lacustrine sediments interbedded with numerous tephra layers. Paleomagnetic study puts the base of the core at about 3.0 Ma. Twelve widespread silicic tephra units provide correlations with other areas and complement age control provided by magnetostratigraphy; mafic and silicic tephra units erupted from local sources are also common in the core. Widespread tephra units include the Llao Rock pumice (=Tsoyawata, 7 ka), the Trego Hot Springs Bed (23 ka), and the Rockland (0.40 Ma), Lava Creek (0.62 Ma), and Rio Dell (1.5 Ma) ash beds, as well as several ash beds also found at Summer Lake, Oregon, and an ash bed originally recognized in DSDP hole 173 in the northeastern Pacific. Several tephra layers found in the core also occur in lacustrine beds exposed around the margins of the basin and elsewhere in the ancestral lacustrine system. Diatoms are present throughout the section. Pollen is present in most of the section, but some barren zones are found in the interval between 50 and 140 m; the greatest change in behavior of the pollen record takes place just above the top of the Olduvai Normal-Polarity Subchronozone. Ostracodes are present only in high-carbonate (>10% CaCO3) intervals. Evolutionary changes are found in the diatom and ostracode records. Bulk geochemical analyses show significant changes in elemental composition of the sediment through time. ?? 1989.

Development of low-ash, planar peat swamps in an alluvial-plain setting: The no. 5 Block beds (westphalian D) of southern West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staub, J.R.; Richards, B.K.

1993-07-01

Coals from the No. 5 Block coal beds (Westphalian D) of the central Appalachian basin are noted for their blocky, dull character and their low ash and low sulfur content. The beds are multiple benched, with rock partings separating benches. Individual benches have limited lateral extent and, where thick, are dominated by bright, high-ash coal at the base and dull, low-ash coal in the upper parts. The duller coals contain more exinite-group and inertinite-group macerals than the brighter coals. These coal beds are encased in sandstone units dominated by fining-upward sequences. The overall depositional setting is an alluvial-plain environment withmore » northwest-flowing channels spaced approximately 20 km apart. The channels were flanked by clastic swamps about 7 km wide. Low-ash peat accumulated in areas of the flood plain most distant from the channels. These peat-accumulating swamps were about 8 km across. In a few instances low-frequency flood events introduced fine siliciclastic sediment into the peat swamps, depositing a thin layer of sediment on top of the peat. This sediment layer is thicker where the underlying coal is the thickest. These thick coal areas are topographically lower than surrounding coal areas. This relationship between coal thickness, parting thickness, and topography indicates that these peat swamps were planar at the time of deposition. Individual coal benches contain abundant preserved cellular tissue (telocollinite, semifusinite, and fusinite) at most locations, suggesting that robust vegetation was widespread in the swamps and that the morphology was planar. The high concentrations of exinite-group an inertinite-group macerals in the upper parts of benches resulted from selective decomposition and oxidation of the peat in subaerial and aquatic planar-swamp environments.« less

Low ash, planar peat swamp development in an alluvial plain setting: The No. 5 block beds of southern West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staub, J.R.; Richards, B.K.

1992-01-01

Coals from the No. 5 Block beds (Westphalian D) are noted for their low ash and sulfur content. Beds are multiple benched, with rock partings separating individual benches. Benches have limited continuity and, where thick are dominated by bright, high ash coal at the base and dull, low ash coal in their upper portions. The duller coals contain more exinite and inertinite group macerals than the brighter coals. The depositional setting is an alluvial plain environment with channel systems separated by distances of about 20 km. The channel systems were flanked by clastic swamps for distances of up to 7more » km or more on either side. Areas of flood plain most distant from the channels were sites where peat accumulated and these zones were about 8 km across. High energy, low frequency flood events introduced fine grained sediment into the peat swamps resulting in thin layers of sediment being deposited on top of the peat. These sediment layers are thicker in areas where the underlying coal is the thickest. These thick coal areas are topographically negative. This relationship between coal and parting thickness and topography indicates that these peat swamps were low-lying or planar. Individual coal benches contain abundant amounts of preserved cellular tissue (telocollinite, semifusinite, fusinite) at most locations indicating that woody arborescent like vegetation was widespread in the swamps suggesting a planar morphology. The high concentrations of exinite and inertinite group macerals found in the upper portions of individual benches resulted from decomposition and oxidation of the peat in subaerial to aquatic planar swamp environments.« less

3D multidisciplinary numerical model of polychlorinated biphenyl dynamics on the Black Sea north-western shelf

NASA Astrophysics Data System (ADS)

Bagaiev, Andrii; Ivanov, Vitaliy

2014-05-01

The Black Sea north-western shelf plays a key role in economics of the developing countries such as Ukraine due to food supply, invaluable recreational potential and variety of the relevant maritime shipping routes. On the other hand, a shallow flat shelf is mostly affected by anthropogenic pollution, eutrophication, hypoxia and harmful algae blooms. The research is focused on modeling the transport and transformation of PCBs (PolyChlorinated Biphenyls) because they are exceedingly toxic and highly resistant to degradation, hence cumulatively affect marine ecosystems. Being lipophilic compounds, PCBs demonstrate the distinguishing sorption/desorption activity taking part in the biogeochemical fluxes via the organic matter particles and sediments. In the framework of the research, the coastal in-situ data on PCB concentration in the water column and sediments are processed, visualized and analyzed. It is concluded that the main sources of PCBs are related to the Danube discharge and resuspension from the shallow-water sediments. Developed 3D numerical model is aimed at simulation of PCB contamination of the water column and sediment. The model integrates the full physics hydrodynamic block as well as modules, which describe detritus transport and transformation and PCB dynamics. Three state variables are simulated in PCB transport module: concentration in solute, on the settling particles of detritus and in the top layer of sediments. PCB adsorption/desorption on detritus; the reversible PCB fluxes at the water-sediment boundary; destruction of detritus are taken into consideration. Formalization of PCB deposition/resuspension in the sediments is adapted from Van Rijn's model of the suspended sediment transport. The model was spun up to reconstruct the short term scenario of the instantaneous PCB release from the St. George Arm of Danube. It has been shown that PCB transport on sinking detritus represents the natural buffer mechanism damping the spreading PCB contamination in the Black Sea shelf ecosystem. Special numerical experiments were carried out to evaluate the artificial sorbent efficiency as a possible post-accidental counter-measure. End-user application is implemented to provide operational PCB forecast in order to support decision making and minimize ecological risks. The graphical user interface allows specifying instantaneous or continuous PCB release scenarios and quick updating the prediction of PCB release trajectory and temporal variability of the mass balance components. It provides visualization of PCB contamination at the sea surface, in the water column and in the upper layer of sediments over time, including the animations of PCB movement. The integrated ocean-ecosystem-sediment-pollution approach developed is applicable to any coastal area and allows further implementation related to advances in the model representation of natural processes and to improvements of PCB monitoring.

Lutz's spontaneous sedimentation technique and the paleoparasitological analysis of sambaqui (shell mound) sediments

PubMed Central

Camacho, Morgana; Pessanha, Thaíla; Leles, Daniela; Dutra, Juliana MF; Silva, Rosângela; de Souza, Sheila Mendonça; Araujo, Adauto

2013-01-01

Parasite findings in sambaquis (shell mounds) are scarce. Although the 121 shell mound samples were previously analysed in our laboratory, we only recently obtained the first positive results. In the sambaqui of Guapi, Rio de Janeiro, Brazil, paleoparasitological analysis was performed on sediment samples collected from various archaeological layers, including the superficial layer as a control. Eggs of Acanthocephala, Ascaridoidea and Heterakoidea were found in the archaeological layers. We applied various techniques and concluded that Lutz's spontaneous sedimentation technique is effective for concentrating parasite eggs in sambaqui soil for microscopic analysis. PMID:23579793

Lutz's spontaneous sedimentation technique and the paleoparasitological analysis of sambaqui (shell mound) sediments.

PubMed

Camacho, Morgana; Pessanha, Thaíla; Leles, Daniela; Dutra, Juliana M F; Silva, Rosângela; Souza, Sheila Mendonça de; Araujo, Adauto

2013-04-01

Parasite findings in sambaquis (shell mounds) are scarce. Although the 121 shell mound samples were previously analysed in our laboratory, we only recently obtained the first positive results. In the sambaqui of Guapi, Rio de Janeiro, Brazil, paleoparasitological analysis was performed on sediment samples collected from various archaeological layers, including the superficial layer as a control. Eggs of Acanthocephala, Ascaridoidea and Heterakoidea were found in the archaeological layers. We applied various techniques and concluded that Lutz's spontaneous sedimentation technique is effective for concentrating parasite eggs in sambaqui soil for microscopic analysis.

Seasonal patterns of bacterial communities in the coastal brackish sediments of the Gulf of Finland, Baltic Sea

NASA Astrophysics Data System (ADS)

Vetterli, Adrien; Hyytiäinen, Kirsi; Ahjos, Minttu; Auvinen, Petri; Paulin, Lars; Hietanen, Susanna; Leskinen, Elina

2015-11-01

Coastal areas are critical in mitigating the impact of nutrient runoffs and downstream eutrophication of aquatic ecosystems. In the Gulf of Finland, the easternmost sub-basin of the Baltic Sea, seasonal and long-term oxygen depletion at the surface of the sediment feeds back the eutrophication loop by promoting the release of nutrients locked in the sediment matrix. In order to understand how the bacterial community responds to the seasonal variations, we sequenced ribosomal gene fragments from the top sediment layer at two coastal sites in southern Finland in spring, summer and late autumn during two consecutive years. Analysis of the samples collected at a shallow (11 m) and deep site (33 m) revealed that the overall community composition was rather constant over time with an extensive collection of shared operational taxonomic units (OTU) between sites. The dominant taxa were related to organoheterotrophs and sulfate reducers and the variation in community structure was linked to the availability of organic matter in the surface sediment. Proteobacteria formed the most abundant and diverse group. The taxa characteristic of spring samples belonged primarily to Actinobacteria, possibly of fresh water origin and linked to humic carbon. Summer communities were characterized by an increase in the number of reads associated with heterotrophic bacteria such as Bacteroidetes which feed on labile organic matter from spring bloom. Taxa typical of autumn samples were linked to Cyanobacteria and other bloom-forming bacteria from the overlying water and to bacteria feeding on organic matter drifting from the phytal zone.

A multi-proxy study of sedimentary humic substances in the salt marsh of the Changjiang Estuary, China

NASA Astrophysics Data System (ADS)

Zhang, Yaoling; Du, Jinzhou; Zhao, Xin; Wu, Wangsuo; Peng, Bo; Zhang, Jing

2014-12-01

To better understand the origin, composition, and reactivity of sedimentary humic substances (HSs) in salt marshes in the Changjiang Estuary, HS samples were isolated from a sediment core that was collected from the Eastern Chongming salt marsh. Chemical and spectroscopic methods were used to analyze the features of these HSs. The results indicate that the studied HSs in the salt marsh sediments are mainly terrestrial-derived and that the sedimentary organic matter (SOM) in the top layer may contain more organic matter from marine sources and/or autochthonous materials due to the dramatic decreasing of the sediment supply as a result of damming. The degradation of labile carbohydrates and proteins and the preservation of refractory lignin components dominate the early diagenetic reactions of SOM in the salt marsh area. The average contents of the carboxylic groups in FAs and HAs are 11.64 ± 1.08 and 7.13 ± 0.16 meq/gC, and those of phenolic groups are 1.95 ± 0.13 and 2.40 ± 0.44 meq/gC, respectively. The content of carboxylic groups increased with increasing depth, while there were no obvious changes in the content of phenolic groups. The average concentration of total proton-binding sites is approximately 12.5 μmol/g sediment for the studied HSs. These values may provide insight into the migration and fate of HS-bound contaminants in sediments and the overlying sea water in the salt marsh areas of the Changjiang Estuary.

Frequency of event deposits reflecting glacial/interglacial conditions during the last ca. 50,000 years in the south Patagonian maar lake Laguna Potrok Aike, Argentina

NASA Astrophysics Data System (ADS)

Kliem, Pierre; Hahn, Annette; Ohlendorf, Christian; Zolitschka, Bernd; Pasado Science Team

2010-05-01

Laguna Potrok Aike is a 100m deep maar lake located in the dry steppe of southern Patagonia. The catchment area of >200km² mainly consists of till from Bella Vista and Río Ciaike Glaciations as well as of alkali-olivine basalts of the Pali Aike Volcanic Field. Today's regional climate is affected by the Southern Hemispheric Westerlies and the rainshadow effect of the north-south striking Andean mountain chain. Since lakes are valuable terrestrial paleoclimate archives, sediments of Laguna Potrok Aike should reflect shifts of mid latitude wind and pressure fields as well as precipitation changes in southeastern South America. Aiming at the reconstruction of past climate, the deep drilling at Laguna Potrok Aike was accomplished in the framework of the ICDP project PASADO during Sept. to Dec. 2008. By correlation of three holes drilled at Site 2 ca. 700 m south of the lake's center, a composite profile of 106.09 mcd (meters composite depth) was established. According to the lowermost 14C-age of aquatic macro remains from 80.6 mcd, the entire record comprises at least 50,000 years. The initial lithological description indicates that 50.74 m (i.e. 47.8%) of the sediment record consists of remobilized sediment (turbidity currents; homogenites; ball and pillow structures, gravel layers, slumps). Such deposits are almost absent in the top 12 mcd, where laminated clays and silts dominate. Correlation with an existing piston core allows a temporal relation to the Holocene. Apart from obviously remobilized deposits Holocene sediments are distinguished from Late Glacial deposits by a lower frequency of coarse silt/fine sand layers within a silt/clay matrix. Frequency and thickness of remobilized deposits increase with sediment depth. Most reworked sections are composed of three units: (1) a dark, coarse and fining upward base overlain by (2) a homogeneous layer of silt and (3) clay capped by a relatively thin light colored clay layer. Such sequences were often described as homogenites from marine sediments but are only rarely known from lakes. In the record from Laguna Potrok Aike thickest homogenites reach up to 3 m in thickness. In contrast, turbidites are characterized by a fining-upward pattern of the entire sequence. Homogenites in lake and marine sediments are generally regarded as representing a record for regional seismicity or tsunami activity. Since homogenites are not only triggered by seismotectonic activity and no such deposits are represented in the Holocene sediments of Laguna Potrok Aike, we hypothesize that homogenite generation could be linked to different climate conditions during glacial times. Reasons for this climate link may be (1) higher clastic input through the main tributary or (2) an extremely low lake level. The first option could be the result of more intense geomorphodynamic processes in the catchment area than today due to periglacial conditions with permafrost, forcing precipitation and melt water to run off superficially. Evidence for permafrost conditions in this region until the end of the last glacial is given by an OSL-dated sand wedge in the catchment area (19.1 ± 1.4ka). The latter explanation is supported by the occurrence of coarse gravel at the bases of some homogenites as well as by one chaotic gravel-dominated unit between 87 and 89 mcd, considering that the distal core is located 1.8 km from the main tributary.

Soft-sediment deformation structures in the late Miocene Şelmo Formation around Adıyaman area, Southeastern Turkey

NASA Astrophysics Data System (ADS)

Koç Taşgın, Calibe; Orhan, Hükmü; Türkmen, İbrahim; Aksoy, Ercan

2011-04-01

The Şelmo Formation was deposited in the basins associated with the Southeastern Anatolian Thrust Belt and East Anatolian Fault Zone in SE Turkey. These structures developed as a result of compressional stresses created by the movement of the Arabian plate to the north and the Eurasian plate to the west from early Miocene to late Pliocene. The outcrops of the Şelmo Formation in the Adýyaman area (SE Turkey) comprise braided river deposits (lower alluvial unit) at the base, lacustrine and deltaic deposits in the middle (lacustrine unit) and low sinuousity river and alluvial deposits at the top (upper alluvial unit). Soft-sediment deformation structures were developed in sandstone, siltstone and marl of the deltaic and lacustrine unit of the Şelmo Formation. These are slumps, recumbent folds, load casts, ball-and-pillow structures, flame structures, neptunian dykes, chaotically associated structures and synsedimentary faults. The tectonic setting of the basin, the lateral extent of the soft-sediment deformation structures over tens of kilometers, their similarities to deformation structures interpreted as being induced seismically in other regions worldwide or in a laboratory setting, and being confined by undeformed layers suggest that the main trigger system was related to seismic activity in the area.

Characterization and origin of spongillite-hosting sediment from João Pinheiro, Minas Gerais, Brazil

NASA Astrophysics Data System (ADS)

Almeida, A. C. S.; Varajão, A. F. D. C.; Gomes, N. S.; Varajão, C. A. C.; Volkmer-Ribeiro, C.

2010-03-01

Spongillite from João Pinheiro, Minas Gerais, Brazil is mainly known for its use in brick production and in the refractory industry. Very few studies have focused on its geological context. Spongillite-rich deposits occur in shallow ponds on a karstic planation surface developed on rocks of the Neoproterozoic São Francisco Supergroup. Cenozoic siliciclastic sediments are related to this surface. A field study of these deposits and analysis of multispectral images showed a SE-NW preferential drainage system at SE, suggesting that Mesozoic Areado Group sandstones were the source area of the spongillite-hosting sediments. Mineralogical and textural characterization by optical microscopic analysis, X-ray diffraction (XRD), differential and gravimetric thermal analysis (DTA-GTA), infrared spectroscopy (IR) and scanning electron microscopy (SEM) of seven open-pit spongillite-rich deposits (Avião, Carvoeiro, Vânio, Preguiça, Divisa, Severino, Feijão) showed a sedimentological similarity between the deposits. They are lens-shaped and are characterized at the bottom by sand facies, in the middle by spicules-rich muddy-sand facies and at the top by organic matter-rich muddy-sand facies. Petrographically, the spongillite-hosting sediments and the siliclastic sediments of the Areado Group show detrital phases with similar mineralogical and textural features, such as the presence of well-sorted quartz grains and surface features of abrasion typical of aeolian reworking that occurred in the depositional environment in which the sandstones of the Areado Group were formed. Detrital heavy minerals, such as staurolite, zircon, tourmaline, and clay minerals, such as kaolinite, low amounts of illite, scarce chlorite and mixed-layer chlorite/smectite and illite/smectite occur in the spongillite-hosting sediments and in sandstones from the Areado Group. In both formations, staurolite has similar chemical composition. These mineralogical and textural features show that the sediments of the Areado Group constitute the main source of the pond sediments that host spongillite.

Rock-avalanche and ocean-resurge deposits in the late Eocene Chesapeake Bay impact structure: Evidence from the ICDP-USGS Eyreville cores, Virginia, USA

USGS Publications Warehouse

Gohn, G.S.; Powars, D.S.; Dypvik, H.; Edwards, L.E.

2009-01-01

An unusually thick section of sedimentary breccias dominated by target-sediment clasts is a distinctive feature of the late Eocene Chesapeake Bay impact structure. A cored 1766-m-deep section recovered from the central part of this marine-target structure by the International Continental Scientific Drilling Program (ICDP)-U.S. Geological Survey (USGS) drilling project contains 678 m of these breccias and associated sediments and an intervening 275-m-thick granite slab. Two sedimentary breccia units consist almost entirely of Cretaceous nonmarine sediments derived from the lower part of the target sediment layer. These sediments are present as coherent clasts and as autoclastic matrix between the clasts. Primary (Cretaceous) sedimentary structures are well preserved in some clasts, and liquefaction and fluidization structures produced at the site of deposition occur in the clasts and matrix. These sedimentary breccias are interpreted as one or more rock avalanches from the upper part of the transient-cavity wall. The little-deformed, unshocked granite slab probably was transported as part of an extremely large slide or avalanche. Water-saturated Cretaceous quartz sand below the slab was transported into the seafloor crater prior to, or concurrently with, the granite slab. Two sedimentary breccia units consist of polymict diamictons that contain cobbles, boulders, and blocks of Cretaceous nonmarine target sediments and less common shocked-rock and melt ejecta in an unsorted, unstratified, muddy, fossiliferous, glauconitic quartz matrix. Much of the matrix material was derived from Upper Cretaceous and Paleogene marine target sediments. These units are interpreted as the deposits of debris flows initiated by the resurge of ocean water into the seafloor crater. Interlayering of avalanche and debris-flow units indicates a partial temporal overlap of the earlier avalanche and later resurge processes. A thin unit of stratified turbidite deposits and overlying laminated fine-grained deposits at the top of the section represents the transition to normal shelf sedimentation. ?? 2009 The Geological Society of America.

Hydrochemistry of the Tumen River Estuary, Sea of Japan

NASA Astrophysics Data System (ADS)

Tishchenko, P. Ya.; Semkin, P. Yu.; Pavlova, G. Yu.; Tishchenko, P. P.; Lobanov, V. B.; Marjash, A. A.; Mikhailik, T. A.; Sagalaev, S. G.; Sergeev, A. F.; Tibenko, E. Yu.; Khodorenko, N. D.; Chichkin, R. V.; Shvetsova, M. G.; Shkirnikova, E. M.

2018-03-01

The hydrological and hydrochemical parameters of the Tumen River estuary were collected at 13 stations in May and October 2015. Vertical temperature, conductivity, dissolved oxygen, chlorophyll fluorescence, and turbidity profiles were obtained. Water was sampled from the surface and bottom layer. The water samples were analyzed for major ions, pH, salinity, concentrations of dissolved oxygen, major nutrients, dissolved organic carbon, humic matter, and δ18O and δD isotopes. This estuary is attributed to microtidal type with a flushing time of about 10 h. A phytoplakton bloom occurred in the top layer of the estuary. For surface horizons, the hydrochemical parameters show a linear correlation with salinity. In the bottom horizons, all these parameters, except for major ions and δ18O and δD isotopes, reveal substantial nonconservative behavior. The nonconservative behavior of the hydrochemical parameters in the bottom waters was mainly caused by degradation of the phytoplankton biomass at the water/sediment interface. Hypoxic conditions were established in the bottom waters of the estuary in May.

The Impacts of Episodic Storm and Flood Events on Carbon and Sediment Delivery to Gulf of Mexico Sediments

NASA Astrophysics Data System (ADS)

Schreiner, K. M.; Carlin, J. A.; Sayers, L.; Swenson, J.

2017-12-01

Marine sediments are an important long-term reservoir for both recently fixed organic carbon (OC) and ancient rock derived OC, much of which is delivered by rivers. The ratio between these two sources of OC in turn regulates atmospheric levels of oxygen and carbon dioxide over geologic time, making this riverine delivery of OC, primarily carried by sediments, an important flux in the global carbon cycle. However, while the overall magnitude of these fluxes are relatively well known, it remains to be determined the importance of episodic events, like storms and floods, in the flux of OC from terrestrial to marine environments. Here, we present data from a 34 cm core collected from the Gulf of Mexico at a mid-shelf distal depocenter for the Brazos River in 2015, during a strong El Nino when that area of the country was experiencing 100-year flood events and anomalously high river flow. Based on analysis of the radioactive isotope 7Be, approximately the top 7-8 cm of the sediment in this core was deposited during this flood event. Both bulk elemental (C, N, and stable carbon isotopes) and chemical biomarker (lignin-phenol) data has been combined to provide information of the origin and chemistry of the OC in this core both before and during flooding. C:N and d13C indicate a mixture of marine-sourced and terrestrially-sourced OC throughout the length of the core with very little variation between the flood layer and deeper sediments. However, lignin-phenol concentrations are higher in flood-deposited sediment, indicating that this sediment is likely terrestrially-sourced. Lignin-phenol indicators of OC degradation state (Acid:Aldehyde ratios) indicate that flood sediment is fresher and less degraded than deeper sediments. Taken together, these results indicate that 1. Bulk analyses are not enough to determine OC source and the importance of flood events in OC cycling and 2. Episodic events like floods could have an oversized impact on OC storage in marine sediments.

Refinement and Verification of Predictive Models of Suspended Sediment Dispersion and Desorption of Toxics from Dredged Sediments.

DTIC Science & Technology

1982-07-01

C ~ DO 680 J=1,NSTEP FOREX =SQRT(ADELX(J+1) *4.* (EZ* ( +EXPCO*EXP( - ’ADELX(J+1)/100.)))) DO 680 IZ=1,21 AZ=(IZ-1) *DELZ TOP=(AZ+XL )/ FOREX - 166 ET...ERF(TOP) BOT= (AZ-XL )/ FOREX EB=ERF (BOT) Z( IZ,J+1)=0. 5*(ET-EB) 680 CONTINUE C C START FINITE DIFFERENCE SOLUTION IF(ISCE.EQ.3)GO TO 25 DO 100 I=IUP

Using Kettle Lake Records to Date and Interpret Holocene Ash Deposition in Upper Cook Inlet, Anchorage, AK

NASA Astrophysics Data System (ADS)

Werner, A.; Kathan, K. M.; Kaufman, D. S.; Hancock, J. R.; Waythomas, C. F.; Wallace, K. L.

2004-12-01

Fourteen sediment cores recovered from three kettle lakes (Goose, Little Campbell and Lorraine) near Anchorage, AK were used to document and date Holocene volcanic ash deposition in the upper Cook Inlet area. Small lakes (<0.5 km2) with small (<1.5 km2), low relief (<50 m), and well-vegetated drainage areas were selected in order to minimize ash remobilization by mass wasting and fluvial processes. The resulting stratigraphic records are interpreted as primary terpha-fall stratigraphies. Relative to the surrounding lacustrine sediments, the ash layers exhibit low organic-matter content (as determined by loss-on-ignition, LOI), high magnetic susceptibility (MS), increased density (X-radiographs), and bubble-wall glass shards. Some ash layers are up to 1 cm thick (macrotephra) consisting of pure glass, some occur as light bands, while others (microtephra) can only be located using non-visual techniques (MS, LOI and X-radiography). The thinnest microtephras observed occur either as discrete (1 mm) layers or diffuse laminations composed of tephra mixed with ambient lake sediment. Forty-five AMS C-14 dates on terrestrial macro fossils were used to constrain sedimentation-rate models for the cores, and to assign absolute ages to ash units. Comparison of inferred tephra ages corroborates our intra and inter basin stratigraphic correlations (+/- 200 yrs) based on physical and MS stratigraphy. Ten out of 12 macrotephras can be confidently correlated among all three lakes, whereas, two of the prominent tephras occur in one basin but not in the others. This suggests subtle differences in ash plume extents or differences in tephra preservation between lakes. A total of 24 Holocene ash units (12 macro and 12 micro) have been recognized and dated in the Anchorage area, suggesting an ash-fall frequency of about 2.4/1000 yrs. By comparison, historical records suggest more frequent ash-fall events (120/1000 yrs). Our data indicate that, either the ash layers are not consistently preserved in the kettle basins, or more likely, these records lack the resolution to differentiate closely spaced ash-fall events. Core top stratigraphies support the latter interpretation: The 10-12 historically observed ash-fall events are represented by two diffuse zones in the upper 15 cm of the cores. As such, ash records from small kettle lakes should be regarded as conservative statements of ash deposition. Further, ash plumes can have narrow geographic distributions and ash-fall thicknesses can change markedly over short distances. Therefore distal ash-fall stratigraphies underestimate eruption frequencies.

Top of head scarp and internal scarps for landslide deposits in the Little North Santiam River Basin, Oregon

USGS Publications Warehouse

Sobieszczyk, Steven

2010-01-01

Data points represent head scarps, flank scarps, and minor internal scarps (linear) associated with landslide deposits in the Little North Santiam River Basin, Oregon. This work was completed as part of the Master's thesis "Turbidity Monitoring and LiDAR Imagery Indicate Landslides are Primary Source of Suspended-Sediment Load in the Little North Santiam River Basin, Oregon, Winter 2009-2010" by Steven Sobieszczyk, Portland State University and U.S. Geological Survey. Data layers in this geodatabase include: landslide deposit boundaries (Deposits); field-verfied location imagery (Photos); head scarp or scarp flanks (Scarp_Flanks); and secondary scarp features (Scarps).The geodatabase template was developed by the Oregon Department of Geology and Mineral Industries (Burns and Madin, 2009).

Processes that generate and deplete liquid water and snow in thin midlevel mixed-phase clouds

NASA Astrophysics Data System (ADS)

Smith, Adam J.; Larson, Vincent E.; Niu, Jianguo; Kankiewicz, J. Adam; Carey, Lawrence D.

2009-06-01

This paper uses a numerical model to investigate microphysical, radiative, and dynamical processes in mixed-phase altostratocumulus clouds. Three cloud cases are chosen for study, each of which was observed by aircraft during the fifth or ninth Complex Layered Cloud Experiment (CLEX). These three clouds are numerically modeled using large-eddy simulation (LES). The observed and modeled clouds consist of a mixed-phase layer with a quasi-adiabatic profile of liquid, and a virga layer below that consists of snow. A budget of cloud (liquid) water mixing ratio is constructed from the simulations. It shows that large-scale ascent/descent, radiative cooling/heating, turbulent transport, and microphysical processes are all significant. Liquid is depleted indirectly via depositional growth of snow (the Bergeron-Findeisen process). This process is more influential than depletion of liquid via accretional growth of snow. Also constructed is a budget of snow mixing ratio, which turns out to be somewhat simpler. It shows that snow grows by deposition in and below the liquid (mixed-phase) layer, and sublimates in the remainder of the virga region below. The deposition and sublimation are balanced primarily by sedimentation, which transports the snow from the growth region to the sublimation region below. In our three clouds, the vertical extent of the virga layer is influenced more by the profile of saturation ratio below the liquid (mixed-phase) layer than by the mixing ratio of snow at the top of the virga layer.

On the relevance of droplet sedimentation in stratocumulus-top mixing

NASA Astrophysics Data System (ADS)

Mellado, Juan Pedro; de Lozar, Alberto

2017-11-01

The interaction between droplet sedimentation, turbulent mixing, evaporative cooling, and radiative cooling at the top of stratocumulus clouds has been studied using direct numerical simulations. This interaction is important to determine the mixing rate of the cloud and dry air above it, which eventually determines the cloud lifetime. By investigating the entrainment-rate equation, which is an analytical relationship between the contributions to cloud-top entrainment from the phenomena indicated above, we have found that the reduction of entrainment velocity by droplet sedimentation can be 2 to 3 times larger than previously conjectured. The reason is twofold. First, the reduction of evaporative cooling as droplets fall out of the inversion is stronger than previously observed in large-eddy simulations, where excessive mixing by turbulence models and numerical artifacts may have partially masked this effect of sedimentation on entrainment. Second, there is a non-negligible direct contribution from mass loading, as falling droplets leave behind more buoyant air in the inversion. This contribution is proportional to the fifth moment of the droplet-size distribution, which provides further evidence for the need to better understand the evolution of the droplet-size distribution.

Surface sediment quality relative to port activities: A contaminant-spectrum assessment.

PubMed

Yu, Shen; Hong, Bing; Ma, Jun; Chen, Yongshan; Xi, Xiuping; Gao, Jingbo; Hu, Xiuqin; Xu, Xiangrong; Sun, Yuxin

2017-10-15

Ports are facing increasing environmental concerns with their importance to the global economy. Numerous studies indicated sediment quality deterioration in ports; however, the deterioration is not discriminated for each port activity. This study investigated a spectrum of contaminants (metals and organic pollutants) in surface sediments at 20 sampling points in Port Ningbo, China, one of the top five world ports by volume. The spectrum of contaminants (metals and organic pollutants) was quantified following marine sediment quality guidelines of China and USA and surface sediment quality was assessed according to thresholds of the two guidelines. Coupling a categorical matrix of port activities with the matrix of sedimentary contaminants revealed that contaminants were highly associated with the port operations. Ship repair posed a severe chemical risk to sediment. Operations of crude oil and coal loadings were two top activities related to organic pollutants in sediments while port operations of ore and container loadings discharged metals. Among the 20 sampling points, Cu, Zn, Pb, and DDT and its metabolites were the priority contaminants influencing sediment quality. Overall, surface sediments in Port Ningbo had relatively low environmental risks but ship repair is an environmental concern that must be addressed. This study provides a practical approach for port activity-related quality assessment of surface sediments in ports that could be applicable in many world sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Sediment Flux of Particulate Organic Phosphorus in the Open Black Sea

NASA Astrophysics Data System (ADS)

Parkhomenko, A. V.; Kukushkin, A. S.

2018-03-01

The interannual variation of the monthly average (weighted average) concentrations of particulate organic phosphorus (PPOM) in the photosynthetic layer, oxycline, redox zone, and H2S zone in the open Black Sea is estimated based on long-term observation data. The suspension sedimentation rates from the studied layers are assessed using model calculations and published data. The annual variation of PPOM sediment fluxes from the photosynthetic layer, oxycline, redox zone, and upper H2S zone to the anaerobic zone of the sea and the correspondingly annual average values are estimated for the first time. A regular decrease in the PPOM annual average flux with depth in the upper active layer is demonstrated. A correlation between the annual average values of PPOM sediment flux from the photosynthetic layer and ascending phosphate flux to this layer is shown, which suggests their balance in the open sea. The results are discussed in terms of the phosphorus biogeochemical cycle and the concept of new and regenerative primary production in the open Black Sea.

Organic matter in sediment layers of an acidic mining lake as assessed by lipid analysis. Part II: Neutral lipids.

PubMed

Poerschmann, Juergen; Koschorreck, Matthias; Górecki, Tadeusz

2017-02-01

Natural neutralization of acidic mining lakes is often limited by organic matter. The knowledge of the sources and degradability of organic matter is crucial for understanding alkalinity generation in these lakes. Sediments collected at different depths (surface sediment layer from 0 to 1 cm and deep sediment layer from 4 to 5cm) from an acidic mining lake were studied in order to characterize sedimentary organic matter based on neutral signature markers. Samples were exhaustively extracted, subjected to pre-chromatographic derivatizations and analyzed by GC/MS. Herein, molecular distributions of diagnostic alkanes/alkenes, terpenes/terpenoids, polycyclic aromatic hydrocarbons, aliphatic alcohols and ketones, sterols, and hopanes/hopanoids were addressed. Characterization of the contribution of natural vs. anthropogenic sources to the sedimentary organic matter in these extreme environments was then possible based on these distributions. With the exception of polycyclic aromatic hydrocarbons, combined concentrations across all marker classes proved higher in the surface sediment layer as compared to those in the deep sediment layer. Alkane and aliphatic alcohol distributions pointed to predominantly allochthonous over autochthonous contribution to sedimentary organic matter. Sterol patterns were dominated by phytosterols of terrestrial plants including stigmasterol and β-sitosterol. Hopanoid markers with the ββ-biohopanoid "biological" configuration were more abundant in the surface sediment layer, which pointed to higher bacterial activity. The pattern of polycyclic aromatic hydrocarbons pointed to prevailing anthropogenic input. Pyrolytic makers were likely to due to atmospheric deposition from a nearby former coal combustion facility. The combined analysis of the array of biomarkers provided new insights into the sources and transformations of organic matter in lake sediments. Copyright © 2016 Elsevier B.V. All rights reserved.

Stochastic Modelling of the Hydraulic Anisotropy of Ash Impoundment Sediment

NASA Astrophysics Data System (ADS)

Slávik, Ivan

2017-12-01

In the case reported here the impoundments of a 400 MW coal heated power plant with an annual production of about 1.5 million tons of fuel ash are of the cross-valley type, operated by the simple and cheap „upstream method”. The aim of the research was to determine overall and local values of the permeability in horizontal as well as in vertical direction and the anisotropy of the thin-layered sedimented ash. The coal ashes are hydraulically transported through pipelines in form of a slurry and periodically floated on the beach of the impoundment. The ashes are deposited in the form of a thin-layered sediment, with random alternation of layers with a coarser or finer granularity. The ash impoundment sediment is anthropogenic sediment with horizontally laminated texture. Therefore, the sediment is anisotropic from the viewpoint of water seepage. The knowledge of the permeability and the seepage anisotropy of the sediment is a basic requirement for the design of an appropriate dewatering system. The seepage anisotropy of the ash sediment has been checked by means of stochastic modelling, based on the correlation between the effective grain diameter and the coefficient of permeability of the ash: the effective grain diameter and the thickness of individual layers have been proposed to be random events.

Recent sediment remolding on a deep shelf, Ross Sea: implications for radiocarbon dating of Antarctic marine sediments

NASA Astrophysics Data System (ADS)

Domack, Eugene W.; Taviani, Marco; Rodriguez, Anthonio

1999-11-01

Coarse, bioclastic rich sands have been widely reported from the banks of the Antarctic continental shelf but their origin is still poorly known. We report on a suite of coarse sediments recovered from the top of the Mawson Bank in the northwestern Ross Sea. Radiocarbon ages of biogenic calcite, for modern and apparently late Pleistocene deposits, range from 1085±45 to 20,895±250 yr B.P.. Discovery of soft tissue (Ascidian) preserved as an incrustation on a pebble at 2 m depth indicates aggregation of the sediment within several months or a year of core recovery. Radiocarbon ages of acid insoluble organic matter (aiom) are less than those of the foraminifera calcite. The aiom ages are also reversed in sequence, indicating reworking of the sediment during deposition. These observations and a review of recently published literature suggest that much of the bank top sediment in Antarctica is presently undergoing remobilization, under the influence of strong currents and/or icebergs even under interglacical (high-stand) sea levels. These observations point out the need for careful, integrated studies on high latitude marine sediment cores before resultant "ages" alone are used as the foundation for paleoglacial reconstructions.

Drizzle formation in stratocumulus clouds: Effects of turbulent mixing

DOE PAGES

Magaritz-Ronen, L.; Pinsky, M.; Khain, A.

2016-02-17

The mechanism of drizzle formation in shallow stratocumulus clouds and the effect of turbulent mixing on this process are investigated. A Lagrangian–Eularian model of the cloud-topped boundary layer is used to simulate the cloud measured during flight RF07 of the DYCOMS-II field experiment. The model contains ~ 2000 air parcels that are advected in a turbulence-like velocity field. In the model all microphysical processes are described for each Lagrangian air volume, and turbulent mixing between the parcels is also taken into account. It was found that the first large drops form in air volumes that are closest to adiabatic andmore » characterized by high humidity, extended residence near cloud top, and maximum values of liquid water content, allowing the formation of drops as a result of efficient collisions. The first large drops form near cloud top and initiate drizzle formation in the cloud. Drizzle is developed only when turbulent mixing of parcels is included in the model. Without mixing, the cloud structure is extremely inhomogeneous and the few large drops that do form in the cloud evaporate during their sedimentation. Lastly, it was found that turbulent mixing can delay the process of drizzle initiation but is essential for the further development of drizzle in the cloud.« less

Drizzle formation in stratocumulus clouds: Effects of turbulent mixing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magaritz-Ronen, L.; Pinsky, M.; Khain, A.

The mechanism of drizzle formation in shallow stratocumulus clouds and the effect of turbulent mixing on this process are investigated. A Lagrangian–Eularian model of the cloud-topped boundary layer is used to simulate the cloud measured during flight RF07 of the DYCOMS-II field experiment. The model contains ~ 2000 air parcels that are advected in a turbulence-like velocity field. In the model all microphysical processes are described for each Lagrangian air volume, and turbulent mixing between the parcels is also taken into account. It was found that the first large drops form in air volumes that are closest to adiabatic andmore » characterized by high humidity, extended residence near cloud top, and maximum values of liquid water content, allowing the formation of drops as a result of efficient collisions. The first large drops form near cloud top and initiate drizzle formation in the cloud. Drizzle is developed only when turbulent mixing of parcels is included in the model. Without mixing, the cloud structure is extremely inhomogeneous and the few large drops that do form in the cloud evaporate during their sedimentation. Lastly, it was found that turbulent mixing can delay the process of drizzle initiation but is essential for the further development of drizzle in the cloud.« less

Kinematics and dynamics of salt movement driven by sub-salt normal faulting and supra-salt sediment accumulation - combined analogue experiments and analytical calculations

NASA Astrophysics Data System (ADS)

Warsitzka, Michael; Kukowski, Nina; Kley, Jonas

2017-04-01

In extensional sedimentary basins, the movement of ductile salt is mainly controlled by the vertical displacement of the salt layer, differential loading due to syn-kinematic deposition, and tectonic shearing at the top and the base of the salt layer. During basement normal faulting, salt either tends to flow downward to the basin centre driven by its own weight or it is squeezed upward due to differential loading. In analogue experiments and analytical models, we address the interplay between normal faulting of the sub-salt basement, compaction and density inversion of the supra-salt cover and the kinematic response of the ductile salt layer. The analogue experiments consist of a ductile substratum (silicone putty) beneath a denser cover layer (sand mixture). Both layers are displaced by normal faults mimicked through a downward moving block within the rigid base of the experimental apparatus and the resulting flow patterns in the ductile layer are monitored and analysed. In the computational models using an analytical approximative solution of the Navier-Stokes equation, the steady-state flow velocity in an idealized natural salt layer is calculated in order to evaluate how flow patterns observed in the analogue experiments can be translated to nature. The analytical calculations provide estimations of the prevailing direction and velocity of salt flow above a sub-salt normal fault. The results of both modelling approaches show that under most geological conditions salt moves downwards to the hanging wall side as long as vertical offset and compaction of the cover layer are small. As soon as an effective average density of the cover is exceeded, the direction of the flow velocity reverses and the viscous material is squeezed towards the elevated footwall side. The analytical models reveal that upward flow occurs even if the average density of the overburden does not exceed the density of salt. By testing various scenarios with different layer thicknesses, displacement rate or lithological parameters of the cover, our models suggest that the reversal of material flow usually requires vertical displacements between 700 and 2000 m. The transition from downward to upward flow occurs at smaller fault displacements, if the initial overburden thickness and the overburden density are high and if sedimentation rate keeps pace with the displacement rate of the sub-salt normal fault.

A laboratory study of sediment and contaminant release during gas ebullition.

PubMed

Yuan, Qingzhong; Valsaraj, Kalliat T; Reible, Danny D; Willson, Clinton S

2007-09-01

Significant quantities of gas are generated from labile organic matter in contaminated sediments. The implications for the gas generation and subsequent release of contaminants from sediments are unknown but may include enhanced direct transport such as pore water advection and diffusion. The behavior of gas in sediments and the resulting migration of a polyaromatic hydrocarbon, viz phenanthrene, were investigated in an experimental system with methane injection at the base of a sediment column. Hexane above the overlying water layer was used to trap any phenanthrene migrating out of the sediment layer. The rate of suspension of solid particulate matter from the sediment bed into the overlying water layer was also monitored. The experiments indicated that significant amounts of both solid particulate matter and contaminant can be released from a sediment bed by gas movement with the amount of release related to the volume of gas released. The effective mass transfer coefficient of gas bubble-facilitated contaminant release was estimated under field conditions, being around three orders of magnitude smaller than that of bioturbation. A thin sand-capping layer (2 cm) was found to dramatically reduce the amount of contaminant or particles released with the gas because it could prevent or at least reduce sediment suspension. Based on the experimental observations, gas bubble-facilitated contaminant transport pathways for both uncapped and capped systems were proposed. Sediment cores were sliced to obtain phenanthrene concentration. X-ray computed tomography (CT) was used to investigate the void space distribution in the sediment penetrated by gas bubbles. The results showed that gas bubble migration could redistribute the sediment void spaces and may facilitate pore water circulation in the sediment.

Ciliate diversity and distribution patterns in the sediments of a seamount and adjacent abyssal plains in the tropical Western Pacific Ocean.

PubMed

Zhao, Feng; Filker, Sabine; Stoeck, Thorsten; Xu, Kuidong

2017-09-12

Benthic ciliates and the environmental factors shaping their distribution are far from being completely understood. Likewise, deep-sea systems are amongst the least understood ecosystems on Earth. In this study, using high-throughput DNA sequencing, we investigated the diversity and community composition of benthic ciliates in different sediment layers of a seamount and an adjacent abyssal plain in the tropical Western Pacific Ocean with water depths ranging between 813 m and 4566 m. Statistical analyses were used to assess shifts in ciliate communities across vertical sediment gradients and water depth. Nine out of 12 ciliate classes were detected in the different sediment samples, with Litostomatea accounting for the most diverse group, followed by Plagiopylea and Oligohymenophorea. The novelty of ciliate genetic diversity was extremely high, with a mean similarity of 93.25% to previously described sequences. On a sediment depth gradient, ciliate community structure was more similar within the upper sediment layers (0-1 and 9-10 cm) compared to the lower sediment layers (19-20 and 29-30 cm) at each site. Some unknown ciliate taxa which were absent from the surface sediments were found in deeper sediments layers. On a water depth gradient, the proportion of unique OTUs was between 42.2% and 54.3%, and that of OTUs shared by all sites around 14%. However, alpha diversity of the different ciliate communities was relatively stable in the surface layers along the water depth gradient, and about 78% of the ciliate OTUs retrieved from the surface layer of the shallowest site were shared with the surface layers of sites deeper than 3800 m. Correlation analyses did not reveal any significant effects of measured environmental factors on ciliate community composition and structure. We revealed an obvious variation in ciliate community along a sediment depth gradient in the seamount and the adjacent abyssal plain and showed that water depth is a less important factor shaping ciliate distribution in deep-sea sediments unlike observed for benthic ciliates in shallow seafloors. Additionally, an extremely high genetic novelty of ciliate diversity was found in these habitats, which points to a hot spot for the discovery of new ciliate species.

Light emitting ceramic device and method for fabricating the same

DOEpatents

Valentine, Paul; Edwards, Doreen D.; Walker Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

2004-11-30

A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, and alternative methods of fabrication for the same are claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

Improvement in top-gate MoS2 transistor performance due to high quality backside Al2O3 layer

NASA Astrophysics Data System (ADS)

Bolshakov, Pavel; Zhao, Peng; Azcatl, Angelica; Hurley, Paul K.; Wallace, Robert M.; Young, Chadwin D.

2017-07-01

A high quality Al2O3 layer is developed to achieve high performance in top-gate MoS2 transistors. Compared with top-gate MoS2 field effect transistors on a SiO2 layer, the intrinsic mobility and subthreshold slope were greatly improved in high-k backside layer devices. A forming gas anneal is found to enhance device performance due to a reduction in the charge trap density of the backside dielectric. The major improvements in device performance are ascribed to the forming gas anneal and the high-k dielectric screening effect of the backside Al2O3 layer. Top-gate devices built upon these stacks exhibit a near-ideal subthreshold slope of ˜69 mV/dec and a high Y-Function extracted intrinsic carrier mobility (μo) of 145 cm2/V.s, indicating a positive influence on top-gate device performance even without any backside bias.

Radiocarbon dating of planktonic foraminifer shells: A cautionary tale

NASA Astrophysics Data System (ADS)

Mekik, Figen

2014-01-01

rate, bioturbation, winnowing, and calcite dissolution produce significant radiocarbon age offsets among multiple species of coexisting planktonic foraminifers and pteropod fragments. We compare the radiocarbon age of foraminifer species and pteropod fragments with estimates of percent calcite dissolved made with a sedimentary proxy (Globorotalia menardii fragmentation index—MFI) to delineate the effect of dissolution on radiocarbon age of foraminifers. Data from two core top transects on the Rio Grande Rise (RIO) and Ontong Java Plateau (OJP) and from down core sediments of varying sedimentation rates in the tropical Pacific (ME-27, MD98 2177, and MW91-9 56GGC) reveal that sediments with the greatest accumulation rates produce the least age offsets among coexisting species. Age offsets among coexisting foraminifers are about 3500 years on RIO, and 1000 years on OJP. Two core tops from RIO yield an age of the Last Glacial Maximum possibly due to mass displacement of younger sediments downslope. Foraminifer age increases with increasing dissolution and there is a consistent pattern of older foraminifer fragments coexisting with younger whole shells of the same species. The only exception is sediments which have experienced high dissolution where fragments are younger than whole shells. The age offset between fragments of G. menardii and its coexisting whole shells does not exceed the age offset among other coexisting foraminifer species in the same core tops.

The relative contribution of near-bed vs. intragravel horizontal transport to fine sediment accumulation processes in river gravel beds

NASA Astrophysics Data System (ADS)

Casas-Mulet, Roser; Lakhanpal, Garima; Stewardson, Michael J.

2018-02-01

Understanding flow-sediment interactions is important for comprehending river functioning. Fine sediment accumulation processes, in particular, have key implications for ecosystem health. However, the amount of fines generated by intragravel flows and later accumulated in gravel streambeds may have been underestimated, as the hydraulic-related driving transport mechanisms in play are not clearly identified. Specifically, the relative contribution of fines from upper vs. lower sediment layers in gravel beds is not well understood. By recreating flooded and dewatered conditions in an experimental flume filled with natural sediment, we estimated such contributions by observing and collecting intragravel transported fines that were later accumulated into a void in the middle of the sediment matrix. Near-bed transport in the upper sediment layers (named Brinkman load) during flooded conditions accounted for most (90%) of the accumulated fines. Intragravel transport in the lower sediment layers (named Interstitial load) was the sole source of transport and accumulation during dewatered conditions with steeper hydraulic gradients. Interstitial load accounted for 10% of the total transport during flooded conditions. Although small, such estimations demonstrate that hydraulic-gradient transport in the lower sediment layers occurs in spite of the contradicting analytical assessments. We provide a case study to challenge the traditional approaches of assessing intragravel transport, and a useful framework to understand the origin and relative contribution of fine sediment accumulation in gravel beds. Such knowledge will be highly useful for the design of monitoring programs aiding river management, particularly in regulated rivers.

In situ observation of the water-sediment interface in combined sewers, using endoscopy.

PubMed

Oms, C; Gromaire, M C; Chebbo, G

2003-01-01

A new method for water-sediment interface observation has been designed. This system is based on a small diameter endoscope protected by a graduated plastic tube. It makes it possible to visualise in a non-destructive manner the sediments and the water-sediment interface. The endoscope was used to investigate Le Marais catchment (Paris): an immobile organic layer was observed at the water-sediment interface. This layer appears in pools of gross bed sediment, at the upstream of collectors, in zones where velocity is slow and where bed shear stress is less than 0.03 N/m2.

Transparent flexible nanogenerator as self-powered sensor for transportation monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhong Lin; Hu, Youfan; Lin, Long

2016-06-14

A traffic sensor includes a flexible substrate having a top surface. A piezoelectric structure extends from the first electrode layer. The piezoelectric structure has a top end. An insulating layer is infused into the piezoelectric structure. A first electrode layer is disposed on top of the insulating layer. A second electrode layer is disposed below the flexible substrate. A packaging layer is disposed around the substrate, the first electrode layer, the piezoelectric structure, the insulating layer and the second electrode layer. In a method of sensing a traffic parameter, a piezoelectric nanostructure-based traffic sensor is applied to a roadway. Anmore » electrical event generated by the piezoelectric nanostructure-based traffic sensor in response to a vehicle interacting with the piezoelectric nanostructure-based traffic sensor is detected. The electrical event is correlated with the traffic parameter.« less

Characterization of a New Organosilicon Photoresist

NASA Astrophysics Data System (ADS)

Cunningham, Wells C.

1987-08-01

For a number of years, there has lo'ep. great interest in organometallic based photoresists for use as the top layer in multilevel resist schemes.-' In general, bilevel approaches to lithography are forced upon the industry as a means of planarizing topography for a subsequent patterning step. This pattern is initially defined by exposure and development of a thin top layer (0.3 to 0.5μm) over the thicker bottom layer (1.0 to 2.0μm). (See Figure 1). In a conventional bilevel approach, the chosen bottom layer is photoactive at a wavelength for which the top is relatively opaque. The top level acts as a portable conformable mask (PCM) for image transfer through the bottom layer after its exposure and wet development. By using a silicon containing photoresist on the top image transfer may be accomplished using an oxygen plasma instead of a second exposure and development. The PCM in this case acts as an etch mask by forming a silicon dioxide crust in the plasma which slows the etch rate of the top versus the bottom layer. A generic curve of etch rate of a photoresist versus percent silicon by weight is shown in Figure 2. The shape is similar over a wide range of organosilicon polymers.5,6

Coating with overlay metallic-cermet alloy systems

NASA Technical Reports Server (NTRS)

Gedwill, M. A.; Levine, S. R.; Glasgow, T. K. (Inventor)

1984-01-01

A base layer of an oxide dispersed, metallic alloy (cermet) is arc plasma sprayed onto a substrate, such as a turbine blade, vane, or the like, which is subjected to high temperature use. A top layer of an oxidation, hot corrosion, erosion resistant alloy of nickel, cobalt, or iron is then arc plasma sprayed onto the base layer. A heat treatment is used to improve the bonding. The base layer serves as an inhibitor to interdiffusion between the protective top layer and the substrate. Otherwise, the 10 protective top layer would rapidly interact detrimentally with the substrate and degrade by spalling of the protective oxides formed on the outer surface at elevated temperatures.

Coastal Change Along the Shore of Northeastern South Carolina - The South Carolina Coastal Erosion Study

USGS Publications Warehouse

Schwab, W.C.; Gayes, P.T.; Morton, R.A.; Driscoll, N.W.; Baldwin, W.E.; Barnhardt, W.A.; Denny, J.F.; Harris, M.S.; Katuna, M.P.; Putney, T.R.; Voulgaris, G.; Warner, J.C.; Wright, E.E.; Barnhardt, Walter A.

2009-01-01

The U.S. Geological Survey, in cooperation with the South Carolina Sea Grant Consortium, conducted a 7-year, multidisciplinary study of coastal erosion in northeastern South Carolina. Shoreline behavior along the coast of Long Bay is dictated by waves, tidal currents, and sediment supply that act within the overall constraints of the regional geologic setting. Beaches are thin ribbons of sand that sit on top of layered sedimentary rocks, which have been deeply eroded by rivers and coastal processes over millions of years. Offshore of the beaches, these sedimentary rocks are exposed as hardgrounds over large expanses of shallow seafloor and are locally overlain by a discontinuous veneer of sandy sediment generally less than 1 m thick. Rates of shoreline retreat largely depend on the geologic framework of the shoreface that is being excavated by ocean processes. Mainland-attached beaches have remained relatively stable, whereas barrier islands have experienced large shifts in shoreline position. In this sediment-limited region, erosion of the shoreface and inner shelf probably contributes a significant amount of new material to the beach system. Oceanographic studies and numerical modeling show that sediment transport varies along the coast, depending on the type and travel path of storms that impact Long Bay, but the long-term net transport direction is generally from north to south. Changes in storm activity that might accompany climate change, coupled with anticipated increases in sea-level rise, are expected to strongly affect low-lying, heavily developed areas of the coast.

Multi-layer coatings

DOEpatents

Maghsoodi, Sina; Brophy, Brenor L.; Abrams, Ze'ev R.; Gonsalves, Peter R.

2016-06-28

Disclosed herein are coating materials and methods for applying a top-layer coating that is durable, abrasion resistant, highly transparent, hydrophobic, low-friction, moisture-sealing, anti-soiling, and self-cleaning to an existing conventional high temperature anti-reflective coating. The top coat imparts superior durability performance and new properties to the under-laying conventional high temperature anti-reflective coating without reducing the anti-reflectiveness of the coating. Methods and data for optimizing the relative thickness of the under-layer high temperature anti-reflective coating and the top-layer thickness for optimizing optical performance are also disclosed.

Cyclotron Orbits of Composite Fermions in the Fractional Quantum Hall Regime

NASA Astrophysics Data System (ADS)

Jo, Insun; Deng, Hao; Liu, Yang; Pfeiffer, L. N.; West, K. W.; Baldwin, K. W.; Shayegan, M.

2018-01-01

We study a bilayer GaAs hole system that hosts two distinct many-body phases at low temperatures and high perpendicular magnetic fields. The higher-density (top) layer develops a Fermi sea of composite fermions (CFs) in its half-filled lowest Landau level, while the lower-density (bottom) layer forms a Wigner crystal (WC) as its filling becomes very small. Owing to the interlayer interaction, the CFs in the top layer feel the periodic Coulomb potential of the WC in the bottom layer. We measure the magnetoresistance of the top layer while changing the bottom-layer density. As the WC layer density increases, the resistance peaks separating the adjacent fractional quantum Hall states in the top layer change nonmonotonically and attain maximum values when the cyclotron orbit of the CFs encloses one WC lattice point. These features disappear at T =275 mK when the WC melts. The observation of such geometric resonance features is unprecedented and surprising as it implies that the CFs retain a well-defined cyclotron orbit and Fermi wave vector even deep in the fractional quantum Hall regime, far from half-filling.

The Grain-size Patchiness of Braided Gravel-Bed Streams: Example of the Urumqi River (northeast Tian Shan, China)

NASA Astrophysics Data System (ADS)

Guerit, L.; Barrier, L.; Narteau, C.; Métivier, F.; Liu, Y.; Lajeunesse, E.; Gayer, E.; Malverti, L.; Meunier, P.; Ye, B.

2012-04-01

In gravel-beds rivers, sediments are sorted into patches of different grain-sizes. For single-thread streams, it has long been shown that this local granulometric sorting is closely linked to the channel morpho-sedimentary elements. For braided streams, this relation is still unclear. In such rivers, many observations of vertical sediment sorting has led to the definition of a surface and a subsurface layers. Because of this common stratification, methods for sampling gravel-bed rivers have been divided in two families. The surface layer is generally sampled by surface methods and the subsurface layer by volumetric methods. Yet, the equivalency between the two kind of techniques is still a key question. In this study, we characterized the grain-size distribution of the surface layer of the Urumqi River, a shallow braided gravel-bed river in China, by surface-count (Wolman grid-by-number) and volumetric (sieve-by-weight) sampling methods. An analysis of two large samples (212 grains and 3226 kg) show that these two methods are equivalent to characterize the river-bed surface layer. Then, we looked at the grain-size distributions of the river-bed morpho-sedimentary elements: (1) chutes at flow constrictions, which pass downstream to (2) anabranches and (3) bars at flow expansions. Using both sampling methods, we measured the diameter of more than 2300 grains and weight more than 6000 kg of grains larger than 4 mm. Our results show that the three morpho-sedimentary elements correspond only to two kinds of grain-size patches: (1) chutes composed of one coarse-grained top layer lying on finer deposits, and (2) anabranches and bars made up of finer-grained deposits more homogeneous in depth. On the basis of these quantitative observations, together with the concave or convex morphology of the different elements, we propose that chute patches form by erosion and transit with size-selective entrainment, whereas anabranch and bar patches rather develop and migrate by transit and deposition. These patch features may be typical of shallow braided gravel-bed rivers and should be considered in future works about on bedload transport processes and their geomorphologic and stratigraphic results.

Low-pass filtered continuum streambed and bedload sediment mass balance laws for an alluvial, gravel-bed stream

NASA Astrophysics Data System (ADS)

DeTemple, B.; Wilcock, P.

2011-12-01

In an alluvial, gravel-bed stream governed by a plane-bed bedload transport regime, the physicochemical properties, size distribution, and granular architecture of the sediment grains that constitute the streambed surface influence many hydrodynamic, geomorphic, chemical, and ecological processes. Consequently, the abilities to accurately characterize the morphology and model the morphodynamics of the streambed surface and its interaction with the bedload above and subsurface below are necessary for a more complete understanding of how sediment, flow, organisms, and biogeochemistry interact. We report on our progress in the bottom-up development of low-pass filtered continuum streambed and bedload sediment mass balance laws for an alluvial, gravel-bed stream. These balance laws are assembled in a four stage process. First, the stream sediment-water system is conceptually abstracted as a nested, multi-phase, multi-species, structured continuum. Second, the granular surface of an aggregate of sediment grains is mathematically defined. Third, an integral approach to mass balance, founded in the continuum theory of multiphase flow, is used to formulate primordial, differential, instantaneous, local, continuum, mass balance laws applicable at any material point within a gravel-bed stream. Fourth, area averaging and time-after-area averaging, employing planform, low-pass filtering expressed as correlation or convolution integrals and based on the spatial and temporal filtering techniques found in the fields of multiphase flow, porous media flow, and large eddy simulation of turbulent fluid flow, are applied to smooth the primordial equations while maximizing stratigraphic resolution and preserving the definitions of relevant morphodynamic surfaces. Our approach unifies, corrects, contextualizes, and generalizes prior efforts at developing stream sediment continuity equations, including the top-down derivations of the surface layer (or "active layer") approach of Hirano [1971a,b] and probabilistic approach of Parker et al. [2000], as well as the bottom-up, low-pass filtered continuum approach of Coleman & Nikora [2009] which employed volume and volume-after-time averaging. It accommodates partial transport (e.g., Wilcock & McArdell [1997], Wilcock [1997a,b]). Additionally, it provides: (1) precise definitions of the geometry and kinematics of sediment in a gravel-bed stream required to collect and analyze the high resolution spatial and temporal datasets that are becoming ever more present in both laboratory and field investigations, (2) a mathematical framework for the use of tracer grains in gravel-bed streams, including the fate of streambed-emplaced tracers as well as the dispersion of tracers in the bedload, (3) spatial and temporal averaging uncompromised by the Reynolds rules necessary to assess the nature of scale separation, and (4) a kinematic foundation for hybrid Langrangian-Eulerian models of sediment morphodynamics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Werne, Roger W.; Sampayan, Stephen; Harris, John Richardson

This patent document discloses high voltage switches that include one or more electrically floating conductor layers that are isolated from one another in the dielectric medium between the top and bottom switch electrodes. The presence of the one or more electrically floating conductor layers between the top and bottom switch electrodes allow the dielectric medium between the top and bottom switch electrodes to exhibit a higher breakdown voltage than the breakdown voltage when the one or more electrically floating conductor layers are not present between the top and bottom switch electrodes. This increased breakdown voltage in the presence of onemore » or more electrically floating conductor layers in a dielectric medium enables the switch to supply a higher voltage for various high voltage circuits and electric systems.« less

Influence of Surrounding Dielectrics on the Data Retention Time of Doped Sb2Te Phase Change Material

NASA Astrophysics Data System (ADS)

Jedema, Friso; in `t Zandt, Micha; Wolters, Rob; Gravesteijn, Dirk

2011-02-01

The crystallization properties of as-deposited and laser written amorphous marks of doped Sb2Te phase change material are found to be only dependent on the top dielectric layer. A ZnS:SiO2 top dielectric layer yields a higher crystallization temperature and a larger crystal growth activation energy as compared to a SiO2 top dielectric layer, leading to superior data retention times at ambient temperatures. The observed correlation between the larger crystallization temperatures and larger crystal growth activation energies indicates that the viscosity of the phase change material in the amorphous state is dependent on the interfacial energy between the phase change material and the top dielectric layer.

The capability of estuarine sediments to remove nitrogen: implications for drinking water resource in Yangtze Estuary.

PubMed

Liu, Lin; Wang, Dongqi; Deng, Huanguang; Li, Yangjie; Chang, Siqi; Wu, Zhanlei; Yu, Lin; Hu, Yujie; Yu, Zhongjie; Chen, Zhenlou

2014-09-01

Water in the Yangtze Estuary is fresh most of the year because of the large discharge of Yangtze River. The Qingcaosha Reservoir built on the Changxing Island in the Yangtze Estuary is an estuarine reservoir for drinking water. Denitrification rate in the top 10 cm sediment of the intertidal marshes and bare mudflat of Yangtze Estuarine islands was measured by the acetylene inhibition method. Annual denitrification rate in the top 10 cm of sediment was 23.1 μmol m(-2) h(-1) in marshes (ranged from 7.5 to 42.1 μmol m(-2) h(-1)) and 15.1 μmol m(-2) h(-1) at the mudflat (ranged from 6.6 to 26.5 μmol m(-2) h(-1)). Annual average denitrification rate is higher at mashes than at mudflat, but without a significant difference (p = 0.084, paired t test.). Taking into account the vegetation and water area of the reservoir, a total 1.42 × 10(8) g N could be converted into nitrogen gas (N2) annually by the sediment, which is 97.7 % of the dissolved inorganic nitrogen input through precipitation. Denitrification in reservoir sediment can control the bioavailable nitrogen level of the water body. At the Yangtze estuary, denitrification primarily took place in the top 4 cm of sediment, and there was no significant spatial or temporal variation of denitrification during the year at the marshes and mudflat, which led to no single factor determining the denitrification process but the combined effects of the environmental factors, hydrologic condition, and wetland vegetation.

Hydrogeologic framework of the middle San Pedro watershed, southeastern Arizona

USGS Publications Warehouse

Dickinson, Jesse; Kennedy, Jeffrey R.; Pool, D.R.; Cordova, Jeffrey T.; Parker, John T.; Macy, J.P.; Thomas, Blakemore

2010-01-01

Water managers in rural Arizona are under increasing pressure to provide sustainable supplies of water despite rapid population growth and demands for environmental protection. This report describes the results of a study of the hydrogeologic framework of the middle San Pedro watershed. The components of this report include: (1) a description of the geologic setting and depositional history of basin fill sediments that form the primary aquifer system, (2) updated bedrock altitudes underlying basin fill sediments calculated using a subsurface density model of gravity data, (3) delineation of hydrogeologic units in the basin fill using lithologic descriptions in driller's logs and models of airborne electrical resistivity data, (4) a digital three-dimensional (3D) hydrogeologic framework model (HFM) that represents spatial extents and thicknesses of the hydrogeologic units (HGUs), and (5) description of the hydrologic properties of the HGUs. The lithologic interpretations based on geophysical data and unit thickness and extent of the HGUs included in the HFM define potential configurations of hydraulic zones and parameters that can be incorporated in groundwater-flow models. The hydrogeologic framework comprises permeable and impermeable stratigraphic units: (1) bedrock, (2) sedimentary rocks predating basin-and-range deformation, (3) lower basin fill, (4) upper basin fill, and (5) stream alluvium. The bedrock unit includes Proterozoic to Cretaceous crystalline rocks, sedimentary rocks, and limestone that are relatively impermeable and poor aquifers, except for saturated portions of limestone. The pre-basin-and-range sediments underlie the lower basin fill but are relatively impermeable owing to cementation. However, they may be an important water-bearing unit where fractured. Alluvium of the lower basin fill, the main water-bearing unit, was deposited in the structural trough between the uplifted ridges of bedrock and (or) pre-basin-and-range sediments. Alluvium of the upper basin fill may be more permeable than the lower basin fill, but it is generally unsaturated in the study area. The lower basin fill stratigraphic unit was delineated into three HGUs on the basis of lithologic descriptions in driller?s logs and one-dimensional (1D) electrical models of airborne transient electromagnetic (TEM) surveys. The interbedded lower basin fill (ILBF) HGU represents an upper sequence having resistivity values between 5 and 40 ohm-m identified as interbedded sand, gravel, and clay in driller?s logs. Below this upper sequence, fine-grained lower basin fill (FLBF) HGU represents a thick silt and clay sequence having resistivity values between 5 and 20 ohm-m. Within the coarse-grained lower basin fill (CLBF) HGU, which underlies the silt and clay of the FLBF, the resistivity values on logs and 1D models increase to several hundred ohm-m and are highly variable within sand and gravel layers. These sequences match distinct resistivity and lithologic layers identified by geophysical logs in the adjacent Sierra Vista subwatershed, suggesting that these sequences are laterally continuous within both the Benson and Sierra Vista subwatersheds in the Upper San Pedro Basin. A subsurface density model based on gravity data was constructed to identify the top of bedrock and structures that may affect regional groundwater flow. The subsurface density model contains six layers having uniform density values, which are assigned on the basis of geophysical logs. The density values for the layers range between 1.65 g/cm3 for unsaturated sediments near the land surface and 2.67 g/cm3 for bedrock. Major features include three subbasins within the study area, the Huachuca City subbasin, the Tombstone subbasin, and the Benson subbasin, which have no expression in surface topography or lithology. Bedrock altitudes from the subsurface density model defined top altitudes of the bedrock HGU. The HFM includes the following HGUs in ascending stratigr

Devices, systems, and methods for conducting assays with improved sensitivity using sedimentation

DOEpatents

Schaff, Ulrich Y.; Koh, Chung-Yan; Sommer, Gregory J.

2016-04-05

Embodiments of the present invention are directed toward devices, systems, and method for conducting assays using sedimentation. In one example, a method includes layering a mixture on a density medium, subjecting sedimentation particles in the mixture to sedimentation forces to cause the sedimentation particles to move to a detection area through a density medium, and detecting a target analyte in a detection region of the sedimentation channel. In some examples, the sedimentation particles and labeling agent may have like charges to reduce non-specific binding of labeling agent and sedimentation particles. In some examples, the density medium is provided with a separation layer for stabilizing the assay during storage and operation. In some examples, the sedimentation channel may be provided with a generally flat sedimentation chamber for dispersing the particle pellet over a larger surface area.

Devices, systems, and methods for conducting assays with improved sensitivity using sedimentation

DOEpatents

Schaff, Ulrich Y; Koh, Chung-Yan; Sommer, Gregory J

2015-02-24

Embodiments of the present invention are directed toward devices, systems, and method for conducting assays using sedimentation. In one example, a method includes layering a mixture on a density medium, subjecting sedimentation particles in the mixture to sedimentation forces to cause the sedimentation particles to move to a detection area through a density medium, and detecting a target analyte in a detection region of the sedimentation channel. In some examples, the sedimentation particles and labeling agent may have like charges to reduce non-specific binding of labeling agent and sedimentation particles. In some examples, the density medium is provided with a separation layer for stabilizing the assay during storage and operation. In some examples, the sedimentation channel may be provided with a generally flat sedimentation chamber for dispersing the particle pellet over a larger surface area.

Intersection of All Top Quantile

EPA Pesticide Factsheets

This layer combines the Top quantiles of the CES, CEVA, and EJSM layers so that viewers can see the overlap of 00e2??hot spots00e2?? for each method. This layer was created by James Sadd of Occidental College of Los Angeles

Are the Element Budget and the Occurrence of Polymetallic Nodules influenced by Fluids Circulating through the Oceanic Crust or/and Sediments?

NASA Astrophysics Data System (ADS)

Heller, C.; Kuhn, T.

2016-12-01

Hydrothermal fluids can extract significant amounts of heat from oceanic lithosphere by lateral fluid flow through permeable basaltic crust of an age of up to 65 Ma. Fluid recharge and discharge occur at basement outcrops in between impermeable pelagic sediments. Recharge of oxic seawater causes upward oxygen diffusion into sediments overlying the permeable basalt in areas proximal to recharge sites. It is suggested that this oxygen have a strong impact on sediments and Mn nodules during fluid exposure time. The aim of this study is to investigate if and how fluid flow through oceanic crust influence the distribution and element budget of the Mn nodules. For that purpose, Mn nodules were examined which were collected during the research cruise SO240 in the equatorial NE Pacific at sites with and without faults in the upper basement and overlying sediments. Faults are thought to be preferred fluid pathways. Nodules were found on the sediment surface as well as in the sediment and consist of different nm- to µm-thick, dense and porous layers. The geochemical composition of bulk nodules and single nodule layers were determined by XRF, ICP-MS/OES and by high resolution analyses with EMPA and LA-ICP-MS. Dense layers have low Mn/Fe ratios (<4) and high concentrations of Co, Zr and REY, while porous layers are characterized by high Mn/Fe ratios (> 10) and high Ni+Cu and Li concentrations (Koschinsky et al., 2010; Kuhn et al., 2010). The different compositions depends on different formation processes of the layers. Dense layers are formed by element precipitation from oxygen rich seawater and/or pore water and are called hydrogenetic, while porous layers were formed by precipitation from almost oxygen-free (suboxic) pore water (Burns & Burns, 1978; Glasby, 2006) and are called diagenetic (Halbach et al., 1988). Preliminary results show that there are significant differences between the geochemical composition of nodules grown at sediment surface and those found within sediments. Compared to surface nodules, buried nodules are enriched in Co and W, but has lower concentration of Mo, Ba, Zn, Li. Distribution of Rare Earth Elements (REY) are also different. Especially, the element distribution in the bulk samples and the single layers of the buried nodules could be used to find a possible influence of circulating fluids on nodule formation.

Remedy and Recontamination Assessment Array

DTIC Science & Technology

2017-03-01

of silica sand visual tracer at interface, (C) addition of thin sand layer, and (D) final result with treatment and overlying water added...Final result for thin clean sediment layer treatment after final installation of treatment and overlying water ... treatment sediments were held in the sediment cells or tubs with overlying surface water under cool conditions overnight prior to application of the

Seismic evidence of exhumed mantle rock basement at the Gorringe Bank and the adjacent Horseshoe and Tagus abyssal plains (SW Iberia)

NASA Astrophysics Data System (ADS)

Sallarès, Valentí; Martínez-Loriente, Sara; Prada, Manel; Gràcia, Eulàlia; Ranero, César; Gutscher, Marc-André; Bartolome, Rafael; Gailler, Audrey; Dañobeitia, Juan José; Zitellini, Nevio

2013-03-01

The Gorringe Bank is a gigantic seamount that separates the Horseshoe and Tagus abyssal plains offshore SW Iberia, in a zone that hosts the convergent boundary between the Africa and Eurasia plates. Although the region has been the focus of numerous investigations since the early 1970s, the lack of appropriate geophysical data makes the nature of the basement, and thus the origin of the structures, still debated. In this work, we present combined P-wave seismic velocity and gravity models along a transect that crosses the Gorringe Bank from the Tagus to the Horseshoe abyssal plains. The P-wave velocity structure of the basement is similar in the Tagus and Horseshoe plains. It shows a 2.5-3.0 km-thick top layer with a velocity gradient twice stronger than oceanic Layer 2 and an abrupt change to an underlying layer with a five-fold weaker gradient. Velocity and density is lower beneath the Gorringe Bank probably due to enhanced fracturing, that have led to rock disaggregation in the sediment-starved northern flank. In contrast to previous velocity models of this region, there is no evidence of a sharp crust-mantle boundary in any of the record sections. The modelling results indicate that the sediment overlays directly serpentinite rock, exhumed from the mantle with a degree of serpentinization decreasing from a maximum of 70-80% under the top of Gorringe Bank to less than 5% at a depth of ˜20 km. We propose that the three domains were originally part of a single serpentine rock band, of nature and possibly origin similar to the Iberia Abyssal Plain ocean-continent transition, which was probably generated during the earliest phase of the North Atlantic opening that followed continental crust breakup (Early Cretaceous). During the Miocene, the NW-SE trending Eurasia-Africa convergence resulted in thrusting of the southeastern segment of the exhumed serpentinite band over the northwestern one, forming the Gorringe Bank. The local deformation associated to plate convergence and uplift could have promoted pervasive rock fracturing of the overriding plate, leading eventually to rock disaggregation in the northern flank of the GB, which could be now a potential source of rock avalanches and tsunamis.

Durable superhydrophobic surfaces made by intensely connecting a bipolar top layer to the substrate with a middle connecting layer.

PubMed

Zhi, Jinghui; Zhang, Li-Zhi

2017-08-30

This study reported a simple fabrication method for a durable superhydrophobic surface. The superhydrophobic top layer of the durable superhydrophobic surface was connected intensely to the substrate through a middle connecting layer. Glycidoxypropyltrimethoxysilane (KH-560) after hydrolysis was used to obtain a hydrophilic middle connecting layer. It could be adhered to the hydrophilic substrate by covalent bonds. Ring-open reaction with octadecylamine let the KH-560 middle layer form a net-like structure. The net-like sturcture would then encompass and station the silica particles that were used to form the coarse micro structures, intensely to increase the durability. The top hydrophobic layer with nano-structures was formed on the KH-560 middle layer. It was obtained by a bipolar nano-silica solution modified by hexamethyldisilazane (HMDS). This layer was connected to the middle layer intensely by the polar Si hydroxy groups, while the non-polar methyl groups on the surface, accompanied by the micro and nano structures, made the surface rather hydrophobic. The covalently interfacial interactions between the substrate and the middle layer, and between the middle layer and the top layer, strengthened the durability of the superhydrophobic surface. The abrasion test results showed that the superhydrophobic surface could bear 180 abrasion cycles on 1200 CW sandpaper under 2 kPa applied pressure.

Manganese cycles in Arctic marine sediments - Climate signals or diagenesis?

NASA Astrophysics Data System (ADS)

März, C.; Stratmann, A.; Eckert, S.; Schnetger, B.; Brumsack, H.-J.

2009-04-01

In comparison to sediments from other parts of the world ocean, the inorganic geochemistry of Arctic Ocean sediments is poorly investigated. However, marked light to dark brown layers are well-known features of Quaternary Arctic sediments, and have been related to variable Mn contents. Brown layers represent intervals relatively rich in Mn (often > 1 wt.%), while yellowish-greyish intervals contain less Mn. As these brown layers are widespread in pelagic Quaternary deposits of the Arctic Ocean, there are attempts to use them as stratigraphic, age-equivalent marker horizons that are genetically related to global climate changes (e.g. Jakobsson et al., 2000; Löwemark et al., 2008). In the Arctic Ocean, other conventional stratigraphic methods often fail, therefore the use of Mn-rich layers as a chemostratigraphic tool seems to be a promising approach. However, several inorganic-geochemical and modelling studies of Mn cycles in the Arctic as well as in other parts of the world ocean have shown that multiple Mn layers in marine sediments can be created by non-steady state diagenetic processes, i.e. secondary Mn redistribution in the sediment due to microbially mediated dissolution-reprecipitation reactions (e.g. Li et al., 1969; Gobeil et al., 1997; Burdige, 2006; Katsev et al., 2006). Such biogeochemical processes can lead to rapid migration or fixation of redox boundaries in the sediment, resulting in the formation or (partial) destruction of metal-rich layers several thousands of years after sediment deposition. As this clearly would alter primary paleoenvironmental signals recorded in the sediments, we see an urgent need to unravel the real stratigraphic potential of Arctic Mn cycles before they are readily established as standard tools. For this purpose, we are studying Mn cycles in Arctic Ocean sediments recovered during R/V Polarstern expedition ARK XXIII/3 on the Mendeleev Ridge (East Siberian Sea). First results of pore water and sediment composition (analysed by ICP-OES and WD-XRF) indicate that certain Mn-rich layers are currently dissolving, while others are forming. This internal Mn re-distribution, while being more pronounced in some locations than in others, also has an impact on related trace metal distributions (e.g. Co, Cu, Ni, Mo). As Mn diagenesis obviously occurs in most cores studied so far (pelagic depositional areas unaffected by turbidites), we conclude that caution has to be taken when applying Mn layers as stratigraphic tools. In addition to more sensitive analyses (acid digestions and HR-ICP-MS measurements), we will apply methods like sequential Mn extraction, X-ray diffraction and electron microscopy to study these Mn-rich layers. These data will be put into a broader context by comparing them to parameters like magnetic susceptibility, grain size distribution, sediment colour or porosity. Hopefully, this will result in a better understanding of Mn biogeochemistry in the Arctic Ocean, including its application as paleoenvironmental proxy. Burdige, D.J. (2006) Geochemistry of marine sediments. Princeton University Press, 609 pp. Gobeil, C., Macdonald, R.W., Sundby, B. (1997) Diagenetic separation of cadmium and manganese in suboxic continental margin sediments. Geochim. Cosmochim. Acta 61, 4647-4654. Jakobsson, M., Løvlie, R., Al-Hanbali, H., Arnold, E.M., Backman, J., Mörth, M. (2000) Manganese and color cycles in Artic Ocean sediments constrain Pleistocene chronology. Geology 8, 23-26. Katsev, S., Sundby, B., Mucci, A. (2006) Modeling vertical excursions of the redox boundary in sediments: Application to deep basins of the Arctic Ocean. Limnol. Oceanogr. 51, 1581-1593. Li, Y.-H., Bischoff, J. Mathieu, G. (1969) Migration of manganese in Arctic Basin sediments. Earth Planet. Sci. Lett. 7, 265-270. Löwemark, L., Jakobsson, M., Mörth, M., Backman, J. (2008) Arctic Ocean manganese contents and sediment colour cycles. Polar. Res. 27, 105-113.

[Influence of Vallisneria spiralis on the physicochemical properties of black-odor sediment in urban sluggish river].

PubMed

Xu, Kuan; Liu, Bo; Wang, Guo-Xiang; Ma, Jiu-Yuan; Cao, Xun; Zhou, Feng

2013-07-01

Using Indoor simulation method, the effect of Vallisneria spiralis on the physicochemical propertise of black and stink sediment was investigated. The surface sediment of urban sluggish river which had been heavily polluted was used as material in the study. The results showed that the redox environment of the sediment was significantly improved by Vallisneria spiralis. During the experiment, the Eh of surface sediment rose from -70 mV to 90 mV. The ferrous content was reduced by 25% in the experiment group while increased by 38% in the control group; the organic matter was decomposed effectively, prevented from natural decomposition to the smelly substances. There was a 3 mm thick greyish yellow oxide layer after 7 days in the experimental group, and the oxide layer gradually thickened over time. The thickness of the oxide layer reached 11 mm at the end of the experiment, and no significant odor was detected. On the contrary, the oxide layer in the control group was only 1 mm thick and the thickness remained unchanged. Meanwhile, an obnoxious odor existed during the whole experiment. The roots of Vallisneria spiralis had significant influence on the porosity of sediment. On one hand, the densification of sediment could be improved by Vallisneria spiralis. On the other hand, Vallisneria spiralis was able to change the state of the surface sediment flows, reduce the erosion of river sediment and inhibit the transfer of black-odor substances, which has a positive ecological meaning.

Hydrogeologic framework, arsenic distribution, and groundwater geochemistry of the glacial-sediment aquifer at the Auburn Road landfill superfund site, Londonderry, New Hampshire

USGS Publications Warehouse

Degnan, James R.; Harte, Philip T.

2013-01-01

Leachate continues to be generated from landfills at the Auburn Road Landfill Superfund Site in Londonderry, New Hampshire. Impermeable caps on the three landfills at the site inhibit direct infiltration of precipitation; however, high water-table conditions allow groundwater to interact with landfill materials from below, creating leachate and ultimately reducing conditions in downgradient groundwater. Reducing conditions can facilitate arsenic transport by allowing it to stay in solution or by liberating arsenic adsorbed to surfaces and from geologic sources, such as glacial sediments and bedrock. The site occupies a 180-acre parcel of land containing streams, ponds, wetlands, and former gravel pits located in glacial sediment. Four areas, totaling 14 acres, including three landfills and one septage lagoon, were used for waste disposal. The site was closed in 1980 after volatile organic compounds associated with industrial waste dumping were detected. The site was added to the U.S. Environmental Protection Agency National Priority List in 1982, and the landfills were capped in 1996. Although volatile organic compound concentrations in groundwater have declined substantially, some measurable concentrations remain. Temporally variable and persistent elevated arsenic concentrations have been measured in groundwater affected by the landfill leachate. Microbial consumption of carbon found in leachate is a driver of reducing conditions that liberate arsenic at the site. In addition to sources of carbon in landfill leachate, wetland areas throughout the site also could contribute carbon to groundwater, but it is currently unknown if any of the wetland areas have downward or reversing gradients that could allow the infiltration of surface water to groundwater. Red-stained sediments and water indicate iron-rich groundwater discharge to surface water and are also associated with elevated concentrations of arsenic in sediment and groundwater. Ironrich groundwater seeps have been observed in the wetland, streams, and pond downgradient of the landfills. Piezometers were installed in some of these locations to confirm groundwater discharge, measure vertical-flow gradients, and to provide a way to sample the discharging groundwater. Understanding the movement of leachate in groundwater is complicated by the presence of preferential flow paths through aquifer materials with differing hydraulic properties; these preferential flow paths can affect rates of recharge, geochemical conditions, and contaminant fluxes. In areas adjacent to the three capped landfills, infiltration of precipitation containing oxygenated water through permeable deltaic sediments in the former gravel pit area causes increases in dissolved oxygen concentrations and decreases in arsenic concentrations. Layered deltaic sediments produce anisotropic hydraulic characteristics and zones of high hydraulic conductivity. The glacial-sediment aquifer also includes glaciolacustrine sediments that have low permeability and limit infiltration at the surface Discharge of leachate-affected groundwater may be limited in areas of organic muck on the bottom of Whispering Pines Pond because the muck may act as a semiconfining layer. Geophysical survey results were used to identify several areas with continuous beds of muck and an underlying highresistivity layer on top of a layer of low resistivity that may represent leachate-affected groundwater. The high-resistivity layer is likely groundwater associated with oxygenated recharge, which would cause arsenic to adsorb onto aquifer sediments and reduce concentrations of dissolved arsenic in groundwater. Surface and borehole geophysical data collected in 2011 were used to identify potentially high-permeability or contaminated zones in the aquifer (preferential flowpaths) as well as low-permeability zones that may promote contamination through back diffusion. Some groundwater in parts of the glacial-sediment aquifer where the leachate plumes were present had low electrical resistivity, low dissolved oxygen, and high concentrations of arsenic. Low-resistivity zones in the underlying bedrock were associated with fractures that also may contain leachate. Although surveying the fractured bedrock was not a specific objective of this study, the results suggest that such a survey would help to determine if leachate and associated concentrations of arsenic are migrating downward into the fractured-bedrock-aquifer system. An uncalibrated, one-dimensional, reactive-transport model was used to assess several conditions that affect arsenic mobility. The results indicate that reductive dissolution and desorption from glacial sediments control dissolved arsenic concentrations. Parameter sensitivity analysis was used to identify key data that are needed in order to accurately assess the time required for arsenic concentrations to fall to levels below the maximum contaminant level at the site. Quantifying this time will require accurate characterization of carbon, sediment-surface sorption sites, and groundwater fluxes at the site.

Stretchable Metamaterial Absorber Using Liquid Metal-Filled Polydimethylsiloxane (PDMS)

PubMed Central

Kim, Kyeongseob; Lee, Dongju; Eom, Seunghyun; Lim, Sungjoon

2016-01-01

A stretchable metamaterial absorber is proposed in this study. The stretchability was achieved by liquid metal and polydimethylsiloxane (PDMS). To inject liquid metal, microfluidic channels were fabricated using PDMS powers and microfluidic-channel frames, which were built using a three-dimensional printer. A top conductive pattern and ground plane were designed after considering the easy injection of liquid metal. The proposed metamaterial absorber comprises three layers of PDMS substrate. The top layer is for the top conductive pattern, and the bottom layer is for the meandered ground plane. Flat PDMS layers were inserted between the top and bottom PDMS layers. The measured absorptivity of the fabricated absorber was 97.8% at 18.5 GHz, and the absorption frequency increased from 18.5 to 18.65 GHz as the absorber was stretched from its original length (5.2 cm) to 6.4 cm. PMID:27077861

Photovoltaic healing of non-uniformities in semiconductor devices

DOEpatents

Karpov, Victor G.; Roussillon, Yann; Shvydka, Diana; Compaan, Alvin D.; Giolando, Dean M.

2006-08-29

A method of making a photovoltaic device using light energy and a solution to normalize electric potential variations in the device. A semiconductor layer having nonuniformities comprising areas of aberrant electric potential deviating from the electric potential of the top surface of the semiconductor is deposited onto a substrate layer. A solution containing an electrolyte, at least one bonding material, and positive and negative ions is applied over the top surface of the semiconductor. Light energy is applied to generate photovoltage in the semiconductor, causing a redistribution of the ions and the bonding material to the areas of aberrant electric potential. The bonding material selectively bonds to the nonuniformities in a manner such that the electric potential of the nonuniformities is normalized relative to the electric potential of the top surface of the semiconductor layer. A conductive electrode layer is then deposited over the top surface of the semiconductor layer.

Ceramic substrate including thin film multilayer surface conductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolf, Joseph Ambrose; Peterson, Kenneth A.

2017-05-09

A ceramic substrate comprises a plurality of ceramic sheets, a plurality of inner conductive layers, a plurality of vias, and an upper conductive layer. The ceramic sheets are stacked one on top of another and include a top ceramic sheet. The inner conductive layers include electrically conductive material that forms electrically conductive features on an upper surface of each ceramic sheet excluding the top ceramic sheet. The vias are formed in each of the ceramic sheets with each via being filled with electrically conductive material. The upper conductive layer includes electrically conductive material that forms electrically conductive features on anmore » upper surface of the top ceramic sheet. The upper conductive layer is constructed from a stack of four sublayers. A first sublayer is formed from titanium. A second sublayer is formed from copper. A third sublayer is formed from platinum. A fourth sublayer is formed from gold.« less

Method of Fabricating Schottky Barrier solar cell

NASA Technical Reports Server (NTRS)

Stirn, R. J.; Yeh, Y. C. M. (Inventor)

1982-01-01

On a thin substrate of low cost material with at least the top surface of the substrate being electrically conductive is deposited a thin layer of heavily doped n-type polycrystalline germanium, with crystalline sizes in the submicron range. A passivation layer may be deposited on the substrate to prevent migration of impurities into the polycrystalline germanium. The polycrystalline germanium is recrystallized to increase the crystal sizes in the germanium layer to not less than 5 micros to serve as a base layer on which a thin layer of gallium arsenide is vapor epitaxially grown to a selected thickness. A thermally-grown oxide layer of a thickness of several tens of angstroms is formed on the gallium arsenide layer. A metal layer, of not more about 100 angstroms thick, is deposited on the oxide layer, and a grid electrode is deposited to be in electrical contact with the top surface of the metal layer. An antireflection coating may be deposited on the exposed top surface of the metal layer.

The effect of sediment thermal conductivity on vertical groundwater flux estimates

NASA Astrophysics Data System (ADS)

Sebok, Eva; Müller, Sascha; Engesgaard, Peter; Duque, Carlos

2015-04-01

The interaction between groundwater and surface water is of great importance both from ecological and water management perspective. The exchange fluxes are often estimated based on vertical temperature profiles taken from shallow sediments assuming a homogeneous standard value of sediment thermal conductivity. Here we report on a field investigation in a stream and in a fjord, where vertical profiles of sediment thermal conductivity and temperatures were measured in order to, (i) define the vertical variability in sediment thermal conductivity, (ii) quantify the effect of heterogeneity in sediment thermal conductivity on the estimated vertical groundwater fluxes. The study was carried out at field sites located in Ringkøbing fjord and Holtum stream in Western Denmark. Both locations have soft, sandy sediments with an upper organic layer at the fjord site. First 9 and 12 vertical sediment temperature profiles up to 0.5 m depth below the sediment bed were collected in the fjord and in the stream, respectively. Later sediment cores of 0.05 m diameter were removed at the location of the temperature profiles. Sediment thermal conductivity was measured in the sediment cores at 0.1 m intervals with a Decagon KD2 Pro device. A 1D flow and heat transport model (HydroGeoSphere) was set up and vertical groundwater fluxes were estimated based on the measured vertical sediment temperature profiles by coupling the model with PEST. To determine the effect of heterogeneity in sediment thermal conductivity on estimated vertical groundwater fluxes, the model was run by assigning (i) a homogeneous thermal conductivity for all sediment layers, calculated as the average sediment thermal conductivity of the profile, (ii) measured sediment thermal conductivities to the different model layers. The field survey showed that sediment thermal conductivity over a 0.5 m profile below the sediment bed is not uniform, having the largest variability in the fjord where organic sediments were also present. Using the measured sediment thermal conductivity for the different model layers instead of a homogeneous distribution did not result in a better fit between observed and simulated sediment temperature profiles. The estimated groundwater fluxes however were greatly affected by using the measured thermal conductivities resulting in changes of ± 45% in estimated vertical fluxes.

Mesoarchean black shale -iron sedimentary sequences in Cleaverville Formation, Pilbara Australia: drilling preliminary result of DXCL2

NASA Astrophysics Data System (ADS)

Kiyokawa, S.; Ito, T.; Ikehara, M.; Yamaguchi, K. E.; Onoue, T.; Horie, K.; Sakamoto, R.; Teraji, S.; Aihara, Y.

2012-12-01

The 3.2-3.1 Ga Dixon island-Cleaverville formations are well-preserved hydrothermal oceanic sequence at oceanic island arc setting (Kiyokawa et al., 2002, 2006, 2012). The Dixon Island (3195+15 Ma) - Cleaverville (3108+13 Ma) formations formed volcano-sedimentary sequences with hydrothermal chert, black shale and banded iron formation to the top. Based on the scientific drilling as DXCL1 at 2007 and DXCL2 at 2011, lithology was clearly understood. Four drilling holes had been done at coastal sites; the Dixon Island Formation is DX site (100m) and the Cleaverville Formation is CL2 (40m), CL1 (60m) and CL3 (200m) sites and from stratigraphic bottom to top. These sequences formed coarsening and thickening upward black shale-BIF sequences. The Dixon Island Formation consists komatiite-rhyolite sequences with many hydrothermal veins and very fine laminated cherty rocks above them. The Cleaverville Formation contains black shale, fragments-bearing pyroclastic beds, white chert, greenish shale and BIF. Especially, CL3 core, which drilled through the Iron formation, shows siderite-chert beds above black shale identified before magnetite lamination bed. The magnetite bed formed very thin laminated bed with siderite lamination. This magnetite bed was covered by black shale beds again. New U-Pb SHRIMP data of the pyroclastic in black shale is 3109Ma. Estimated 2-8 cm/1000year sedimentation rate are identified in these sequences. Our preliminary result show that siderite and chert layers formed before magnetite iron sedimentation. The lower-upper sequence of organic carbon rich black shales are similar amount of organic content and 13C isotope (around -30per mill). So we investigate that the Archean iron formation, especially Cleaverville iron formation, was highly related by hydrothermal input and started pre-syn iron sedimentation at anoxic oceanic condition.

Geomicrobiology of Fe-rich crusts in Lake Superior sediment

NASA Astrophysics Data System (ADS)

Dittrich, M.; Monreau, L.; Quazi, S.; Raoof, B.; Chesnyuk, A.; Katsev, S.; Fulthorpe, R.

2012-04-01

The limnological puzzles of Lake Superior are increasingly attracting scientists, and very little is known about the sediments and their associated microflora. The sediments are organic poor (less than 5%C) and the lake is deep oligotrophic, with water temperatures at the bottom around 3C. Previous studies reveal Fe-rich layers in the sediments at multiple loccations around the lake. The origin and mechanisms of formation of this layer remain unknown. In this study we investigated geochemical and microbiological processes that may lead to the formation of a two cm thick iron layer about 10 cm below the sediment surface. Sediment cores from two stations (EM, 230m water depth and ED, 310m water depth) in the East Basin were used. We monitored oxygen and pH depth profiles with microsensors, porewater and sediment solid matter were analyzed for nutrient and metal contents. Furthermore, phosphorus and iron sequantial extractions of sediment cores have been perfomed. The total cell count was determined using DAPI epifluoresence microscopy. DNA was extracted from the sediment samples and 16S ribosonal RNA amplicons were analyzed with denaturing gradient gel electrophoresis (DGGE). For a more in depth analysis, DNA samples from 8-10 cm and 10-12 cm were sent to the Research and Testing Lab (Texas) for pyrosequencing of 16S rRNA gene amplicons amplified using barcoded universal primers 27f-519r. The scanning electron microscope (SEM) images from the iron layer 10-12cm show filaments that were encrusted with spheres ca. 20 nm in diameter. SEM observations of thin sections also indicate the presence of very fine particles showing various morphologies. Analyses of the deposit material by SEM and energy dispersive X-ray spectroscopy (EDS) indicate that bacteria cells surfaces served as nucleation surfaces for Fe-oxide formation. EDS line-scans through bacterial cells covered with precipitates reveal phosphorus and carbon peaks at interface between cell surface and Fe-particles. The cluster analysis performed on the DGGE separation of ribosomal RNA gene fragments revealed that the two iron layers were not highly similar to each other. We obtained a total of 26,062 16S rRNA gene sequence reads from the two iron layers and the layers directly above them, which were clustered into operational taxonomic units sharing 80% similarity or more. 64-70% of these clusters could not be classified below the phylum level. While the 8-10 cm sediment layers were dominated (46.5% of reads) by relatives of Paenisporosarcina, the iron layers contained far fewer gram positive organisms, far more proteobacteria, and an a high proportion of Nitrospira species which show relatively high similarity to organisms found in an iron II rich seep.

Optical Properties of Hybrid Inorganic/Organic Thin Film Encapsulation Layers for Flexible Top-Emission Organic Light-Emitting Diodes.

PubMed

An, Jae Seok; Jang, Ha Jun; Park, Cheol Young; Youn, Hongseok; Lee, Jong Ho; Heo, Gi-Seok; Choi, Bum Ho; Lee, Choong Hun

2015-10-01

Inorganic/organic hybrid thin film encapsulation layers consist of a thin Al2O3 layer together with polymer material. We have investigated optical properties of thin film encapsulation layers for top-emission flexible organic light-emitting diodes. The transmittance of hybrid thin film encapsulation layers and the electroluminescent spectrum of organic light-emitting diodes that were passivated by hybrid organic/inorganic thin film encapsulation layers were also examined as a function of the thickness of inorganic Al203 and monomer layers. The number of interference peaks, their intensity, and their positions in the visible range can be controlled by varying the thickness of inorganic Al2O3 layer. On the other hand, changing the thickness of monomer layer had a negligible effect on the optical properties. We also verified that there is a trade-off between transparency in the visible range and the permeation of water vapor in hybrid thin film encapsulation layers. As the number of dyads decreased, optical transparency improved while the water vapor permeation barrier was degraded. Our study suggests that, in top-emission organic light-emitting diodes, the thickness of each thin film encapsulation layer, in particular that of the inorganic layer, and the number of dyads should be controlled for highly efficient top-emission flexible organic light-emitting diodes.

Shifts among Eukaryota, Bacteria, and Archaea define the vertical organization of a lake sediment.

PubMed

Wurzbacher, Christian; Fuchs, Andrea; Attermeyer, Katrin; Frindte, Katharina; Grossart, Hans-Peter; Hupfer, Michael; Casper, Peter; Monaghan, Michael T

2017-04-08

Lake sediments harbor diverse microbial communities that cycle carbon and nutrients while being constantly colonized and potentially buried by organic matter sinking from the water column. The interaction of activity and burial remained largely unexplored in aquatic sediments. We aimed to relate taxonomic composition to sediment biogeochemical parameters, test whether community turnover with depth resulted from taxonomic replacement or from richness effects, and to provide a basic model for the vertical community structure in sediments. We analyzed four replicate sediment cores taken from 30-m depth in oligo-mesotrophic Lake Stechlin in northern Germany. Each 30-cm core spanned ca. 170 years of sediment accumulation according to 137 Cs dating and was sectioned into layers 1-4 cm thick. We examined a full suite of biogeochemical parameters and used DNA metabarcoding to examine community composition of microbial Archaea, Bacteria, and Eukaryota. Community β-diversity indicated nearly complete turnover within the uppermost 30 cm. We observed a pronounced shift from Eukaryota- and Bacteria-dominated upper layers (<5 cm) to Bacteria-dominated intermediate layers (5-14 cm) and to deep layers (>14 cm) dominated by enigmatic Archaea that typically occur in deep-sea sediments. Taxonomic replacement was the prevalent mechanism in structuring the community composition and was linked to parameters indicative of microbial activity (e.g., CO 2 and CH 4 concentration, bacterial protein production). Richness loss played a lesser role but was linked to conservative parameters (e.g., C, N, P) indicative of past conditions. By including all three domains, we were able to directly link the exponential decay of eukaryotes with the active sediment microbial community. The dominance of Archaea in deeper layers confirms earlier findings from marine systems and establishes freshwater sediments as a potential low-energy environment, similar to deep sea sediments. We propose a general model of sediment structure and function based on microbial characteristics and burial processes. An upper "replacement horizon" is dominated by rapid taxonomic turnover with depth, high microbial activity, and biotic interactions. A lower "depauperate horizon" is characterized by low taxonomic richness, more stable "low-energy" conditions, and a dominance of enigmatic Archaea.

Temporal and spatial variability of the sediment grain-size distribution on the Eel shelf: The flood layer of 1995

USGS Publications Warehouse

Drake, D.E.

1999-01-01

Sediment grain-size characteristics observed on the Eel shelf have been analyzed using a wet-sieving technique that minimizes breakage of aggregates. At several sites on the 70-m isobath north of the river, where a 1995 flood layer attained a maximum thickness of about 9 cm, replicate box cores were collected on seven cruises during February 1995 to January 1997. These samples provide a unique opportunity to follow the evolution of a flood layer over a two-year period as it was modified and gradually buried. One month after the flood, a layer of tan-colored, high-porosity sediment with up to 96% of its particles in the size range of 0-20 ??m had accumulated on the central part of the shelf, 7-30 km north of the river and principally between the 50-m and 90-m isobaths. Substantial coarsening of this layer occurred between February 1995 and May 1995, particularly along the southern and the landward edge of the deposit in water depths of <70 m. The early stage of coarsening was probably caused by physical reworking of the surface 0.5-cm of the deposit and by addition of new sediment from shallower regions of the shelf. Temporal changes in inventories of several grain-size fractions show that physical processes continued to add coarse sediment to the flood layer after May 1995, but the large increases in thickness of the surface mixed layer could only be attributed to bioturbation by a recovering, or seasonally fluctuating, benthic community. The 1995 flood layer has evolved from exhibiting limited variability and normal grading (i:e., upward fining) to a layer that (1) shows significant spatial variability on scales from centimeters to 10's of meters, (2) is substantially coarser owing to additions of sediment from the inner shelf, (3) is inversely graded (i.e., coarsens upward), and (4) is intensely bioturbated to depths of 4-5 cm.

Core evidence of paleoseismic events in Paleogene deposits of the Shulu Sag in the Bohai Bay Basin, east China, and their petroleum geologic significance

NASA Astrophysics Data System (ADS)

Zheng, Lijing; Jiang, Zaixing; Liu, Hui; Kong, Xiangxin; Li, Haipeng; Jiang, Xiaolong

2015-10-01

The Shulu Sag, located in the southwestern corner of the Jizhong Depression, Bohai Bay Basin of east China, is a NE-SW trending, elongate Cenozoic half-graben basin. The lowermost part of the third member of the Shahejie Formation in this basin is characterized by continental rudstone and calcilutite to calcisiltite facies. Based on core observation and regional geologic analysis, seismites are recognized in these lacustrine deposits, which include soft-sediment deformation structures (sedimentary dikes, hydraulic shattering, diapir structures, convolute lamination, load-flame structures, ball-and-pillow structures, loop bedding, and subsidence structures), synsedimentary faults, and seismoturbidites. In addition, mixed-source rudstones, consisting of the Paleozoic carbonate clasts and in situ calcilutite clasts in the lowermost submember of Shahejie 3, appear in the seismites, suggesting an earthquake origin. A complete representative vertical sequence in the lowermost part of the third member found in well ST1H located in the central part of the Shulu Sag shows, from the base to the top: underlying undeformed layers, synsedimentary faults, liquefied carbonate rocks, allogenetic seismoturbidites, and overlying undeformed layers. Seismites are widely distributed around this well and there are multiple sets of stacked seismites separated by undeformed sediment. The nearby NW-trending Taijiazhuang fault whose fault growth index is from 1.1 to 1.8 and the NNE-trending Xinhe fault with a fault growth index of 1.3-1.9 may be the source of the instability to create the seismites. These deformed sedimentary layers are favorable for the accumulation of oil and gas; for example, sedimentary dikes can cut through many layers and serve as conduits for fluid migration. Sedimentary faults and fractures induced by earthquakes can act as oil and gas migration channels or store petroleum products as well. Seismoturbidites and mixed-source rudstones are excellent reservoirs due to their abundant primary or dissolved pores.

U.S. Geological Survey ArcMap Sediment Classification tool

USGS Publications Warehouse

O'Malley, John

2007-01-01

The U.S. Geological Survey (USGS) ArcMap Sediment Classification tool is a custom toolbar that extends the Environmental Systems Research Institute, Inc. (ESRI) ArcGIS 9.2 Desktop application to aid in the analysis of seabed sediment classification. The tool uses as input either a point data layer with field attributes containing percentage of gravel, sand, silt, and clay or four raster data layers representing a percentage of sediment (0-100%) for the various sediment grain size analysis: sand, gravel, silt and clay. This tool is designed to analyze the percent of sediment at a given location and classify the sediments according to either the Folk (1954, 1974) or Shepard (1954) as modified by Schlee(1973) classification schemes. The sediment analysis tool is based upon the USGS SEDCLASS program (Poppe, et al. 2004).

Paper plant effluent revisited-southern Lake Champlain, Vermont and New York

USGS Publications Warehouse

Haupt, R.S.; Folger, D.W.

1993-01-01

We used geologic and geochemical techniques to document the change with time of the distribution and concentration of contaminated bottom sediments in southern Lake Champlain near an International Paper Company plant. Our work, initiated in 1972, was expanded on behalf of Vermont citizens in a class-action suit against the International Paper Company. To update our 1972-1973 results, we collected nine cores in 1988 upstream and downstream from the paper plant effluent diffuser. Water content, volatile solids, organic carbon, and three ratios, Al/Si, Cl/Si, and S/Si, in addition to megascopic and microscopic observations, were evaluated to identify and trace the distribution of effluent and to measure the thickness of sediment affected by or containing components of effluent. Analyses were carried out on samples from the cores as well as from effluent collected directly from the plant's waste treatment facility. In 1973, two years after the plant opened, we cored near the diffuser; sediment contaminated with effluent was 4.5 cm thick. In 1988, in the same area, sediment contaminated with effluent was 17 cm thick. In 15 years, water content increased from 72 to 85 percent, volatile solids from 7 to 20 percent, and organic carbon from 2 to 12 percent. Cl/Si and S/Si were high only near the diffuser and were zero elsewhere. In the area of the diffuser, contaminated sediment appears to be accumulating at a rate of about 1 cm/yr. At a control location 22 km upstream (south) from the plant, the top, poorly consoli-dated layer was only 1 cm or less thick both in 1973 and in 1988. The class-action suit was settled in favor of the plaintiffs for $5 million. ?? 1993 Springer-Verlag.

Paleoceanographic history of the Lower Bengal Fan during the last glacial cycle - IODP Expedition 354

NASA Astrophysics Data System (ADS)

Dekens, P. S.; Weber, M. E.; Lantzsch, H.; Das, S. K.; Williams, T.; Adhikari, R. R.; Jia, G.; Fox, L. R.; Ge, J.; Manoj, M. C.; Savian, J. F.; Reilly, B. T.; Selkin, P. A.; Meynadier, L.; Spiess, V.; France-Lanord, C.; Sharma, B.

2015-12-01

IODP Expedition 354 drilled a ~320 km long transect of seven sites on the Lower Bengal Fan at 8o N in the Northern Indian Ocean. The sediments cores recovered record a complex relationship between turbiditic and hemipelagic environments. This variability offers a unique opportunity to link our understanding of tectonic and terrestrial processes with climate and oceanography. With the exception the westernmost Site U1454, all sites show a several meter thick, hemipelagic top layer, usually representing Late Quaternary sediment. We present physical, geochemical and stable isotopic properties of this interval to establish a time frame and assess the paleoceanographic development of the region during the last glacial cycle. We sampled Site U1452C-1H continuously for the uppermost 480 cm of hemipelagic sediment in 2-cm increments. Preliminary results indicate the Toba Ash 1 (0.74 ka) is a distinct time marker in all physical properties. Furthermore, wet-bulk density as well as color reflectance b* (the red-green component) and L* (the lightness) show a dominant precession cyclicity. Hence, we are able to provide an insolation-tuned chronology for the last 200 ka (MIS1 - 7) as a preliminary age model. These records agree well with d18O records retrieved from Chinese caves. We will present a preliminary paleoceanographic proxy data to reconstruct sea-surface temperature (SST), sea-surface salinity (SSS), ice volume, marine biological productivity, nutrient supply, and deep-water circulation. These oceanographic and climate conditions are linked to changes in monsoonal strength and terrestrial input using sedimentary proxies to reconstruct chemical weathering and sediment sources and transport time. This work addresses one of the primary cruise objectives - linking monsoon variability, regional and global climate, and Bay of Bengal sediment deposition.

Viral infections stimulate the metabolism and shape prokaryotic assemblages in submarine mud volcanoes.

PubMed

Corinaldesi, Cinzia; Dell'Anno, Antonio; Danovaro, Roberto

2012-06-01

Mud volcanoes are geological structures in the oceans that have key roles in the functioning of the global ecosystem. Information on the dynamics of benthic viruses and their interactions with prokaryotes in mud volcano ecosystems is still completely lacking. We investigated the impact of viral infection on the mortality and assemblage structure of benthic prokaryotes of five mud volcanoes in the Mediterranean Sea. Mud volcano sediments promote high rates of viral production (1.65-7.89 × 10(9) viruses g(-1) d(-1)), viral-induced prokaryotic mortality (VIPM) (33% cells killed per day) and heterotrophic prokaryotic production (3.0-8.3 μgC g(-1) d(-1)) when compared with sediments outside the mud volcano area. The viral shunt (that is, the microbial biomass converted into dissolved organic matter as a result of viral infection, and thus diverted away from higher trophic levels) provides 49 mgC m(-2) d(-1), thus fuelling the metabolism of uninfected prokaryotes and contributing to the total C budget. Bacteria are the dominant components of prokaryotic assemblages in surface sediments of mud volcanoes, whereas archaea dominate the subsurface sediment layers. Multivariate multiple regression analyses show that prokaryotic assemblage composition is not only dependant on the geochemical features and processes of mud volcano ecosystems but also on synergistic interactions between bottom-up (that is, trophic resources) and top-down (that is, VIPM) controlling factors. Overall, these findings highlight the significant role of the viral shunt in sustaining the metabolism of prokaryotes and shaping their assemblage structure in mud volcano sediments, and they provide new clues for our understanding of the functioning of cold-seep ecosystems.

Viral infections stimulate the metabolism and shape prokaryotic assemblages in submarine mud volcanoes

PubMed Central

Corinaldesi, Cinzia; Dell'Anno, Antonio; Danovaro, Roberto

2012-01-01

Mud volcanoes are geological structures in the oceans that have key roles in the functioning of the global ecosystem. Information on the dynamics of benthic viruses and their interactions with prokaryotes in mud volcano ecosystems is still completely lacking. We investigated the impact of viral infection on the mortality and assemblage structure of benthic prokaryotes of five mud volcanoes in the Mediterranean Sea. Mud volcano sediments promote high rates of viral production (1.65–7.89 × 109 viruses g−1 d−1), viral-induced prokaryotic mortality (VIPM) (33% cells killed per day) and heterotrophic prokaryotic production (3.0–8.3 μgC g−1 d−1) when compared with sediments outside the mud volcano area. The viral shunt (that is, the microbial biomass converted into dissolved organic matter as a result of viral infection, and thus diverted away from higher trophic levels) provides 49 mgC m−2 d−1, thus fuelling the metabolism of uninfected prokaryotes and contributing to the total C budget. Bacteria are the dominant components of prokaryotic assemblages in surface sediments of mud volcanoes, whereas archaea dominate the subsurface sediment layers. Multivariate multiple regression analyses show that prokaryotic assemblage composition is not only dependant on the geochemical features and processes of mud volcano ecosystems but also on synergistic interactions between bottom-up (that is, trophic resources) and top-down (that is, VIPM) controlling factors. Overall, these findings highlight the significant role of the viral shunt in sustaining the metabolism of prokaryotes and shaping their assemblage structure in mud volcano sediments, and they provide new clues for our understanding of the functioning of cold-seep ecosystems. PMID:22170423

Two layer structure for reinforcing pothole repair

NASA Astrophysics Data System (ADS)

Yuan, Wei; Yuan, Kuo-Yao; Zou, Linhua; Yang, Jenn-Ming; Ju, Jiann-Wen; Kao, Wei; Carlson, Larry

2013-04-01

We have applied dicyclopentadiene (DCPD) resin for reinforcing pothole patch materials due to its unique properties - low cost, low viscosity at beginning and ultra-toughness after curing, chemical compatibility with tar, tunable curing profile through catalyst design. In this paper, we have designed a two layer structure - well compacted base layer and DCPD reinforced 1-1.5" top layer - for pothole repair. By choosing two graded asphalt mixes, a porous top layer and fully compacted base layer was prepared after compaction and ready for DCPD resin infiltration. The DCPD curing and infiltration profile within this porous top layer was measured with thermocouples. The rutting resistance was tested with home-made wheel rutter. The cage effect due to the p-DCPD wrapping was characterized with wheel penetration test. The results showed that this two layer structure pothole repair has greatly improved properties and can be used for pothole repair to increase the service life.

Device for thermal transfer and power generation

DOEpatents

Weaver, Stanton Earl [Northville, NY; Arik, Mehmet [Niskayuna, NY

2011-04-19

A system is provided. The system includes a device that includes top and bottom thermally conductive substrates positioned opposite to one another, wherein a top surface of the bottom thermally conductive substrate is substantially atomically flat and a thermal blocking layer disposed between the top and bottom thermally conductive substrates. The device also includes top and bottom electrodes separated from one another between the top and bottom thermally conductive substrates to define a tunneling path, wherein the top electrode is disposed on the thermal blocking layer and the bottom electrode is disposed on the bottom thermally conductive substrate.

Sediment unmixing using detrital geochronology

USGS Publications Warehouse

Sharman, Glenn R.; Johnstone, Samuel

2017-01-01

Sediment mixing within sediment routing systems can exert a strong influence on the preservation of provenance signals that yield insight into the influence of environmental forcings (e.g., tectonism, climate) on the earth’s surface. Here we discuss two approaches to unmixing detrital geochronologic data in an effort to characterize complex changes in the sedimentary record. First we summarize ‘top-down’ mixing, which has been successfully employed in the past to characterize the different fractions of prescribed source distributions (‘parents’) that characterize a derived sample or set of samples (‘daughters’). Second we propose the use of ‘bottom-up’ methods, previously used primarily for grain size distributions, to model parent distributions and the abundances of these parents within a set of daughters. We demonstrate the utility of both top-down and bottom-up approaches to unmixing detrital geochronologic data within a well-constrained sediment routing system in central California. Use of a variety of goodness-of-fit metrics in top-down modeling reveals the importance of considering the range of allowable mixtures over any single best-fit mixture calculation. Bottom-up modeling of 12 daughter samples from beaches and submarine canyons yields modeled parent distributions that are remarkably similar to those expected from the geologic context of the sediment-routing system. In general, mixture modeling has potential to supplement more widely applied approaches in comparing detrital geochronologic data by casting differences between samples as differing proportions of geologically meaningful end-member provenance categories.

Sediment unmixing using detrital geochronology

NASA Astrophysics Data System (ADS)

Sharman, Glenn R.; Johnstone, Samuel A.

2017-11-01

Sediment mixing within sediment routing systems can exert a strong influence on the preservation of provenance signals that yield insight into the effect of environmental forcing (e.g., tectonism, climate) on the Earth's surface. Here, we discuss two approaches to unmixing detrital geochronologic data in an effort to characterize complex changes in the sedimentary record. First, we summarize 'top-down' mixing, which has been successfully employed in the past to characterize the different fractions of prescribed source distributions ('parents') that characterize a derived sample or set of samples ('daughters'). Second, we propose the use of 'bottom-up' methods, previously used primarily for grain size distributions, to model parent distributions and the abundances of these parents within a set of daughters. We demonstrate the utility of both top-down and bottom-up approaches to unmixing detrital geochronologic data within a well-constrained sediment routing system in central California. Use of a variety of goodness-of-fit metrics in top-down modeling reveals the importance of considering the range of allowable that is well mixed over any single best-fit mixture calculation. Bottom-up modeling of 12 daughter samples from beaches and submarine canyons yields modeled parent distributions that are remarkably similar to those expected from the geologic context of the sediment-routing system. In general, mixture modeling has the potential to supplement more widely applied approaches in comparing detrital geochronologic data by casting differences between samples as differing proportions of geologically meaningful end-member provenance categories.

75 FR 447 - In the Matter of Certain Semiconductor Chips With Minimized Chip Package Size and Products...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

... review (1) the finding that the claim term ``top layer'' recited in claim 1 of the '106 patent means ``an outer layer of the chip assembly upon which the terminals are fixed,'' the requirement that ``the `top layer' is a single layer,'' and the effect of the findings on the infringement analysis, invalidity...

Structural and electrical investigations of MBE-grown SiGe nanoislands

NASA Astrophysics Data System (ADS)

Şeker, İsa; Karatutlu, Ali; Gürbüz, Osman; Yanık, Serhat; Bakış, Yakup; Karakız, Mehmet

2018-01-01

SiGe nanoislands were grown by Molecular Beam Epitaxy (MBE) method on Si (100) substrates with comparative growth parameters such as annealing temperature, top Ge content and layer-by-layer annealing (LBLA). XRD and Raman data suggest that annealing temperature, top Ge content and layer-by-layer annealing (LBLA) can overall give a control not only over the amorphous content but also over yielding the strained Ge layer formation in addition to mostly Ge crystallites. Depending on the layer design and growth conditions, size of the crystallites was observed to be changed. Four Point Probe (FPP) Method via Semiconductor Analyzer shows that 100 °C rise in annealing temperature of the samples with Si0.25Ge0.75 top layers caused rougher islands with vacancies which further resulted in the formation of laterally higher resistive thin film sheets. However, vertically performed I-AFM analysis produced higher I-V values which suggest that the vertical and horizantal conductance mechanisms appear to be different. Ge top-layered samples gained greater crystalline structure and better surface conductivity where LBLA resulted in the formation of Ge nucleation and tight 2D stacking resulting in enhanced current values.

Erosion and sedimentation from the 17 July, 1998 Papua New Guinea tsunami

USGS Publications Warehouse

Gelfenbaum, G.; Jaffe, B.

2003-01-01

This paper describes erosion and sedimentation associated with the 17 July 1998 Papua New Guinea tsunami. Observed within two months of the tsunami, distinct deposits of a layer averaging 8-cm thick of gray sand rested on a brown muddy soil. In most cases the sand is normally graded, with more coarse sand near the base and fine sand at the top. In some cases the deposit contains rip-up clasts of muddy soil and in some locations it has a mud cap. Detailed measurements of coastal topography, tsunami flow height and direction indicators, and deposit thickness were made in the field, and samples of the deposit were collected for grain-size analysis in the laboratory. Four shore-normal transects were examined in detail to assess the shore-normal and along shore distribution of the tsunami deposit. Near the shoreline, the tsunami eroded approximately 10-25 cm of sand from the beach and berm. The sandy layer deposited by the tsunami began 50-150 m inland from the shoreline and extended across the coastal plain to within about 40 m of the limit of inundation; a total distance of up to 750 m from the beach. As much as 2/3 of the sand in the deposit originated from offshore. Across most of the coastal plain the deposit thickness and mean grain size varied little. In the along-shore direction the deposit thickness varied with the tsunami wave height; both largest near the entrance to Sissano Lagoon.

High-resolution near-surface velocity model building using full-waveform inversion—a case study from southwest Sweden

NASA Astrophysics Data System (ADS)

Adamczyk, A.; Malinowski, M.; Malehmir, A.

2014-06-01

Full-waveform inversion (FWI) is an iterative optimization technique that provides high-resolution models of subsurface properties. Frequency-domain, acoustic FWI was applied to seismic data acquired over a known quick-clay landslide scar in southwest Sweden. We inverted data from three 2-D seismic profiles, 261-572 m long, two of them shot with small charges of dynamite and one with a sledgehammer. To our best knowledge this is the first published application of FWI to sledgehammer data. Both sources provided data suitable for waveform inversion, the sledgehammer data containing even wider frequency spectrum. Inversion was performed for frequency groups between 27.5 and 43.1 Hz for the explosive data and 27.5-51.0 Hz for the sledgehammer. The lowest inverted frequency was limited by the resonance frequency of the standard 28-Hz geophones used in the survey. High-velocity granitic bedrock in the area is undulated and very shallow (15-100 m below the surface), and exhibits a large P-wave velocity contrast to the overlying normally consolidated sediments. In order to mitigate the non-linearity of the inverse problem we designed a multiscale layer-stripping inversion strategy. Obtained P-wave velocity models allowed to delineate the top of the bedrock and revealed distinct layers within the overlying sediments of clays and coarse-grained materials. Models were verified in an extensive set of validating procedures and used for pre-stack depth migration, which confirmed their robustness.

Role of organic phosphorus in sediment in a shallow eutrophic lake

NASA Astrophysics Data System (ADS)

Shinohara, Ryuichiro; Hiroki, Mikiya; Kohzu, Ayato; Imai, Akio; Inoue, Tetsunori; Furusato, Eiichi; Komatsu, Kazuhiro; Satou, Takayuki; Tomioka, Noriko; Shimotori, Koichi; Miura, Shingo

2017-08-01

We tested the hypothesis that mineralization of molybdenum unreactive phosphorus (MUP) in pore water is the major pathway for the changes in the concentration of molybdenum-reactive P (MRP) in pore water and inorganic P in sediment particles. The concentration of inorganic P in the sediment particles increased from December to April in Lake Kasumigaura, whereas concentrations of organic P in the sediment particles and MUP in pore water decreased. These results suggest that MUP mineralization plays a key role as the source of MRP, whereas desorption of inorganic P from the sediment particles into the pore water is a minor process. One-dimensional numerical simulation of sediment particles and the pore water supported the hypothesis. Diffusive flux of MUP was small in pore water, even in near-surface layers, so mineralization was the dominant process for changing the MUP concentration in the pore water. For MRP, diffusion was the dominant process in the surface layer, whereas adsorption onto the sediment was the dominant process in deeper layers. Researchers usually ignore organic P in the sediment, but organic P in sediment particles and the pore water is a key source of inorganic P in the sediment particles and pore water; our results suggest that in Lake Kasumigaura, organic P in the sediment is an important source, even at depths more than 1 cm below the sediment surface. In contrast, the large molecular size of MUP in pore water hampers diffusion of MUP from the sediment into the overlying water.

Reprint of: A numerical investigation of fine sediment resuspension in the wave boundary layer-Uncertainties in particle inertia and hindered settling

NASA Astrophysics Data System (ADS)

Cheng, Zhen; Yu, Xiao; Hsu, Tian-Jian; Balachandar, S.

2016-05-01

The wave bottom boundary layer is a major conduit delivering fine terrestrial sediments to continental margins. Hence, studying fine sediment resuspensions in the wave boundary layer is crucial to the understanding of various components of the earth system, such as carbon cycles. By assuming the settling velocity to be a constant in each simulation, previous turbulence-resolving numerical simulations reveal the existence of three transport modes in the wave boundary layer associated with sediment availabilities. As the sediment availability and hence the sediment-induced stable stratification increases, a sequence of transport modes, namely, (I) well-mixed transport, (II) formulation of lutocline resembling a two-layer system, and (III) completely laminarized transport are observed. In general, the settling velocity is a flow variable due to hindered settling and particle inertia effects. Present numerical simulations including the particle inertia suggest that for a typical wave condition in continental shelves, the effect of particle inertia is negligible. Through additional numerical experiments, we also confirm that the particle inertia tends (up to the Stokes number St = 0.2) to attenuate flow turbulence. On the other hand, for flocs with lower gelling concentrations, the hindered settling can play a key role in sustaining a large amount of suspended sediments and results in the laminarized transport (III). For the simulation with a very significant hindered settling effect due to a low gelling concentration, results also indicate the occurrence of gelling ignition, a state in which the erosion rate is always higher than the deposition rate. A sufficient condition for the occurrence of gelling ignition is hypothesized for a range of wave intensities as a function of sediment/floc properties and erodibility parameters.

7 CFR 51.1527 - Standard pack.

Code of Federal Regulations, 2010 CFR

2010-01-01

... plums or prunes in the top layer of any package shall be reasonably representative in quality and size... minimum diameter, or number of fruit per package, or in accordance with the arrangement of the top layer... peach boxes, lug boxes and small consumer packages. In layer-packed California peach boxes or lug boxes...

Determination of radiocarbon reservoir age of Lake Van by mineral magnetic and geochemical analysis

NASA Astrophysics Data System (ADS)

Makaroglu, Ozlem; Namik Cagatay, M.; Pesonen, Lauri J.; Orbay, Naci

2017-04-01

Lake Van is the largest soda lake in the world, located on the east Anatolian Plateau in Turkey. Its varved sediments provide an excellent archive of high-resolution paleoclimate record for the Near East. Varve counting and radiocarbon methods are therefore important dating techniques for investigating the Lake Van sedimentary paleoclimate record. In here we present detailed magnetic and geochemical record of Lake Van. We have studied 4.56 m (core VP0801) and 4.70 m (core VP0807) long cores recovered from 80 m and 65 m water depths located in SE and SW of Lake Van, respectively. Here, we have benefited from magnetic properties with associated remanent magnetization of the sediments from Lake Van to correlate the cores which contain of tephra layers. The cores cover the last 8.4 ka and lithologically include three laminated sedimentary units. From top to the bottom, the units were dated 4.2 ka BP-present, 5.4-4.2 ka BP and older than 5.4 ka BP. We identified tephra layers previously dated by varve counting, and used the varve ages to obtain age models for the cores. We also obtained a total of eight Accelerator Mass Spectrometry (AMS) 14C dates from total organic carbon (TOC) in the two cores, close to the tephra layers. Comparison of the varve ages of the AMS 14C dated samples with their corresponding AMS 14C dates indicates large differences, suggesting significant reservoir ages that range from 2.8 to 2.5 ka for 3.0-2.4 varve ka BP and from 2.8 to 3.3 ka for 8.0-5.9 varve ka BP. The results suggest that the reservoir age of the organic matter increases with the varve age of the sediments. This increase is mainly related to the rate of supply of "dead" carbon from the old carbonate rocks in the watershed of Lake Van, which was relatively higher during 8.4-5.9 ka than during 3.0-2.4 ka BP because of the higher atmospheric precipitation and higher rate of biochemical weathering during the former period.

Low-Noise Large-Area Photoreceivers with Low Capacitance Photodiodes

NASA Technical Reports Server (NTRS)

Joshi, Abhay M. (Inventor); Datta, Shubhashish (Inventor)

2013-01-01

A quad photoreceiver includes a low capacitance quad InGaAs p-i-n photodiode structure formed on an InP (100) substrate. The photodiode includes a substrate providing a buffer layer having a metal contact on its bottom portion serving as a common cathode for receiving a bias voltage, and successive layers deposited on its top portion, the first layer being drift layer, the second being an absorption layer, the third being a cap layer divided into four quarter pie shaped sections spaced apart, with metal contacts being deposited on outermost top portions of each section to provide output terminals, the top portions being active regions for detecting light. Four transimpedance amplifiers have input terminals electrically connected to individual output terminals of each p-i-n photodiode.

Hydrogeologic Framework in Three Drainage Basins in the New Jersey Pinelands, 2004-06

USGS Publications Warehouse

Walker, Richard L.; Reilly, Pamela A.; Watson, Kara M.

2008-01-01

The U.S. Geological Survey, in cooperation with the New Jersey Pinelands Commission, began a multi-phase hydrologic investigation in 2004 to characterize the hydrologic system supporting the aquatic and wetland communities of the New Jersey Pinelands area (Pinelands). The Pinelands is an ecologically diverse area in the southern New Jersey Coastal Plain underlain by the Kirkwood-Cohansey aquifer system. The demand for ground water from this aquifer system is increasing as local development increases. To assess the effects of ground-water withdrawals on Pinelands stream and wetland water levels, three drainage basins were selected for detailed hydrologic assessments, including the Albertson Brook, McDonalds Branch and the Morses Mill Stream basins. Study areas were defined surrounding the three drainage basins to provide sub-regional hydrogeologic data for the ground-water flow modeling phase of this study. In the first phase of the hydrologic assessments, a database of hydrogeologic information and a hydrogeologic framework model for each of the three study areas were produced. These framework models, which illustrate typical hydrogeologic variations among different geographic subregions of the Pinelands, are the structural foundation for predictive ground-water flow models to be used in assessing the hydrologic effects of increased ground-water withdrawals. During 2004-05, a hydrogeologic database was compiled using existing and new geophysical and lithologic data including suites of geophysical logs collected at 7 locations during the drilling of 21 wells and one deep boring within the three study areas. In addition, 27 miles of ground-penetrating radar (GPR) surface geophysical data were collected and analyzed to determine the depth and extent of shallow clays in the general vicinity of the streams. On the basis of these data, the Kirkwood-Cohansey aquifer system was divided into 7 layers to construct a hydrogeologic framework model for each study area. These layers are defined by their predominant sediment textures as aquifers and leaky confining layers. The confining layer at the base of the Kirkwood-Cohansey aquifer system, depending on location, is defined as one of two distinct clays of the Kirkwood Formation. The framework models are described using hydrogeologic sections, maps of structure tops of layers, and thickness maps showing variations of sediment textures of the various model layers. The three framework models are similar in structure but unique to their respective study areas. The hydraulic conductivity of the Kirkwood-Cohansey aquifer system in the vicinity of the three study areas was determined from analysis of 16 slug tests and 136 well-performance tests. The mean values for hydraulic conductivity in the three study areas ranged from about 84 feet per day to 130 feet per day. With the exception of the basal confining layers, the variable and discontinuous nature of clay layers within the Kirkwood-Cohansey aquifer system was confirmed by the geophysical and lithologic records. Leaky confining layers and discontinuous clays are generally more common in the upper part of the aquifer system. Although the Kirkwood-Cohansey aquifer system generally has been considered a water-table aquifer in most areas, localized clays in the aquifer layers and the effectiveness of the leaky confining layers may act to impede the flow of ground water in varying amounts depending on the degree of confinement and the location, duration, and magnitude of the hydraulic stresses applied. Considerable variability exists in the different sediment textures. The extent to which this hydrogeologic variability can be characterized is constrained by the extent of the available data. Thus, the hydraulic properties of the modeled layers were estimated on the basis of available horizontal hydraulic conductivity data and the range of sediment textures estimated from geophysical and lithologic data.

Observations of the R reflector and sediment interface reflection at the Shallow Water '06 Central Site.

PubMed

Choi, Jee Woong; Dahl, Peter H; Goff, John A

2008-09-01

Acoustic bottom-interacting measurements from the Shallow Water '06 experiment experiment (frequency range 1-20 kHz) are presented. These are co-located with coring and stratigraphic studies showing a thin (approximately 20 cm) higher sound speed layer overlaying a thicker (approximately 20 m) lower sound speed layer ending at a high-impedance reflector (R reflector). Reflections from the R reflector and analysis of the bottom reflection coefficient magnitude for the upper two sediment layers confirm both these features. Geoacoustic parameters are estimated, dispersion effects addressed, and forward modeling using the parabolic wave equation undertaken. The reflection coefficient measurements suggest a nonlinear attenuation law for the thin layer of sandy sediments.

Interdigitated photovoltaic power conversion device

DOEpatents

Ward, James Scott; Wanlass, Mark Woodbury; Gessert, Timothy Arthur

1999-01-01

A photovoltaic power conversion device has a top surface adapted to receive impinging radiation. The device includes at least two adjacent, serially connected cells. Each cell includes a semi-insulating substrate and a lateral conductivity layer of a first doped electrical conductivity disposed on the substrate. A base layer is disposed on the lateral conductivity layer and has the same electrical charge conductivity thereof. An emitter layer of a second doped electrical conductivity of opposite electrical charge is disposed on the base layer and forms a p-n junction therebetween. A plurality of spaced channels are formed in the emitter and base layers to expose the lateral conductivity layer at the bottoms thereof. A front contact grid is positioned on the top surface of the emitter layer of each cell. A first current collector is positioned along one outside edge of at least one first cell. A back contact grid is positioned in the channels at the top surface of the device for engagement with the lateral conductivity layer. A second current collector is positioned along at least one outside edge of at least one oppositely disposed second cell. Finally, an interdigitation mechanism is provided for serially connecting the front contact grid of one cell to the back contact grid of an adjacent cell at the top surface of the device.

Interdigitated photovoltaic power conversion device

DOEpatents

Ward, J.S.; Wanlass, M.W.; Gessert, T.A.

1999-04-27

A photovoltaic power conversion device has a top surface adapted to receive impinging radiation. The device includes at least two adjacent, serially connected cells. Each cell includes a semi-insulating substrate and a lateral conductivity layer of a first doped electrical conductivity disposed on the substrate. A base layer is disposed on the lateral conductivity layer and has the same electrical charge conductivity thereof. An emitter layer of a second doped electrical conductivity of opposite electrical charge is disposed on the base layer and forms a p-n junction therebetween. A plurality of spaced channels are formed in the emitter and base layers to expose the lateral conductivity layer at the bottoms thereof. A front contact grid is positioned on the top surface of the emitter layer of each cell. A first current collector is positioned along one outside edge of at least one first cell. A back contact grid is positioned in the channels at the top surface of the device for engagement with the lateral conductivity layer. A second current collector is positioned along at least one outside edge of at least one oppositely disposed second cell. Finally, an interdigitation mechanism is provided for serially connecting the front contact grid of one cell to the back contact grid of an adjacent cell at the top surface of the device. 15 figs.

Mechanical Controls on Halokinesis in Layered Evaporite Sequences: Insights from 2D Geomechanical Forward Models

NASA Astrophysics Data System (ADS)

Goteti, Rajesh; Agar, Susan M.; Brown, John P.; Ball, Philip; Zuhlke, Rainer

2017-04-01

Mechanical stratification in LES (Layered Evaporate Sequences) can have a distinct impact on structural and depositional styles in rifted margin salt tectonics. The bulk mechanical response of an LES under geological loading is dependent, among other factors, on the relative proportions of salt and sediment, salt mobility and sedimentation rate. To assess the interactions among the aforementioned factors in a physically consistent manner, we present 2D, large-strain finite element models of an LES salt minibasin and diapirs. Loading from the deposition of alternating salt and sediment layers (i.e., LES), gravity and a prescribed geothermal gradient provide the driving force for halokinesis in the models. To accurately capture the mechanical impact of stratification within the modeled LES, salt is assigned a temperature-dependent visco-plastic rheology, whereas the sediments are assigned a non-associative cap-plasticity model that supports both compaction and shear localization. Perturbations in the initial salt-sediment interface are used to initiate the salt diapirs. Model results suggest that active diapirism in the basal halite layer initiates when the pressure at the base of the incipient salt diapir exceeds that beneath the minibasin. Vertical growth of the diapir is also accompanied by its lateral expansion at higher structural levels where it preferentially intrudes the adjacent pre- and syn-kinematic salt layers. This pressure pumping of deeper salt into shallow salt layers, can result in rapid thickness changes between successive sediment layers within the LES. Caution needs to be exercised as such thickness changes observed in seismic images may not be entirely due to the shifting of depocenters but also due to the lateral pumping of salt within the LES. The presence of salt layers at multiple structural levels decouples the deformation between successive clastic layers resulting in disharmomic folding with contrasting strain histories in the sedimentary stringers. A significant proportion of the bulk deviatoric strain is preferentially partitioned into the salt layers. Effective plastic shear strains within the sediment stringers generally remain low in the minibasin but can be significantly higher with attendant intense folding near the diapirs. In non-LES systems, the shape of a salt diapir is often used as indicator of relative rates of salt supply and sedimentation over geological time. However our models suggest that this rule-of-thumb may not apply in LES where the shape of the salt diapir is a function of the mechanical properties of the salt layers at various structural levels in addition to the relative rates of salt supply and sedimentation. Imaging challenges in LES may preclude placing strong constraints on structural timing based on interpretation of interfaces between the stringers and the salt diapir. In such situations, geomechanical forward modeling can be a useful tool in placing physics-based quantitative constraints on the timing of LES structures.

GDGT and alkenone flux in the northern Gulf of Mexico: Implications for the TEX86 and UK137 paleothermometers

USGS Publications Warehouse

Richey, Julie; Tierney, Jessica E.

2016-01-01

The TEX86 and molecular biomarker proxies have been broadly applied in down-core marine sediments to reconstruct past sea surface temperature (SST). Although both TEX86 and have been interpreted as proxies for mean annual SST throughout the global ocean, regional studies of GDGTs and alkenones in sinking particles are required to understand the influence of seasonality, depth distribution and diagenesis on downcore variability. We measure GDGT and alkenone flux, as well as the TEX86 and indices in a 4-year sediment trap time series (2010-2014) in the northern Gulf of Mexico (nGoM), and compare these data with core-top sediments at the same location. GDGT and alkenone fluxes do not show a consistent seasonal cycle, however the largest flux peaks for both occurs in winter. co-varies with SST over the 4-year sampling interval, but the -SST relationship in this data set implies a smaller slope or non-linearity at high temperatures when compared with existing calibrations. Furthermore, the flux-weighted value from sinking particles is significantly lower than that of underlying core-top sediments, suggesting preferential diagenetic loss of the tri-unsaturated alkenone in sediments. TEX86 does not co-vary with SST, suggesting production in the subsurface upper water column. The flux-weighted mean TEX86 matches that of core-top sediments, confirming that TEX86 in the nGoM reflects local planktonic production rather than allochthonous or in-situ sedimentary production. We explore potential sources of uncertainty in both proxies in the nGoM, but demonstrate that they show nearly identical trends in 20th century SST, despite these factors.

Geophysical and hydrologic studies of lake seepage variability

USGS Publications Warehouse

Toran, Laura; Nyquist, Jonathan E.; Rosenberry, Donald O.; Gagliano, Michael P.; Mitchell, Natasha; Mikochik, James

2014-01-01

Variations in lake seepage were studied along a 130 m shoreline of Mirror Lake NH. Seepage was downward from the lake to groundwater; rates measured from 28 seepage meters varied from 0 to −282 cm/d. Causes of this variation were investigated using electrical resistivity surveys and lakebed sediment characterization. Two-dimensional (2D) resistivity surveys showed a transition in lakebed sediments from outwash to till that correlated with high- and low-seepage zones, respectively. However, the 2D survey was not able to predict smaller scale variations within these facies. In the outwash, fast seepage was associated with permeability variations in a thin (2 cm) layer of sediments at the top of the lakebed. In the till, where seepage was slower than that in the outwash, a three-dimensional resistivity survey mapped a point of high seepage associated with heterogeneity (lower resistivity and likely higher permeability). Points of focused flow across the sediment–water interface are difficult to detect and can transmit a large percentage of total exchange. Using a series of electrical resistivity geophysical methods in combination with hydrologic data to locate heterogeneities that affect seepage rates can help guide seepage meter placement. Improving our understanding of the causes and types of heterogeneity in lake seepage will provide better data for lake budgets and prediction of mass transfer of solutes or contaminants between lakes and groundwater.

Splay fault branching from the Hikurangi subduction shear zone: Implications for slow slip and fluid flow

NASA Astrophysics Data System (ADS)

Plaza-Faverola, A.; Henrys, S.; Pecher, I.; Wallace, L.; Klaeschen, D.

2016-12-01

Prestack depth migration data across the Hikurangi margin, East Coast of the North Island, New Zealand, are used to derive subducting slab geometry, upper crustal structure, and seismic velocities resolved to ˜14 km depth. We investigate the potential relationship between the crustal architecture, fluid migration, and short-term geodetically determined slow slip events. The subduction interface is a shallow dipping thrust at <7 km depth near the trench and steps down to 14 km depth along an ˜18 km long ramp, beneath Porangahau Ridge. This apparent step in the décollement is associated with splay fault branching and coincides with a zone of maximum slip (90 mm) inferred on the subduction interface during slow slip events in June and July 2011. A low-velocity zone beneath the plate interface, updip of the plate interface ramp, is interpreted as fluid-rich overpressured sediments capped with a low permeability condensed layer of chalk and interbedded mudstones. Fluid-rich sediments have been imbricated by splay faults in a region that coincides with the step down in the décollement from the top of subducting sediments to the oceanic crust and contribute to spatial variation in frictional properties of the plate interface that may promote slow slip behavior in the region. Further, transient fluid migration along splay faults at Porangahau Ridge may signify stress changes during slow slip.

Sunset

NASA Technical Reports Server (NTRS)

1992-01-01

This cross section of the Earth's atmosphere at sunset and earth limb (24.5S, 43.5E) displays an unusual layering believed to be caused by temperature inversions which effectively concentrate smoke, dust and aerosols into narrow layers. the top of the stratosphere can be seen as the top of the white layer thought to contain volcanic debris. The purple layer is the troposphere containing smoke from landclearing biomass burning.

Sunset

NASA Image and Video Library

1992-11-01

This cross section of the Earth's atmosphere at sunset and earth limb (24.5S, 43.5E) displays an unusual layering believed to be caused by temperature inversions which effectively concentrate smoke, dust and aerosols into narrow layers. the top of the stratosphere can be seen as the top of the white layer thought to contain volcanic debris. The purple layer is the troposphere containing smoke from landclearing biomass burning.

The atomic geometries of GaP(110) and ZnS(110) revisited - A structural ambiguity and its resolution

NASA Technical Reports Server (NTRS)

Duke, C. B.; Paton, A.; Kahn, A.

1984-01-01

The atomic geometries of GaP(110) and ZnS(110) are reexamined using the R-factor minimization procedure, developed for GaAs(110) and previously applied to GaSb(110), ZnTe(110), InAs(110), and AlP(110), to analyze experimental elastic low-energy electron diffraction intensities. Unlike most of the earlier cases, both GaP(110) and ZnS(110) exhibit two distinct minimum-Rx structures which cannot be distinguished by analysis of the shapes of the intensity profiles alone. One region of best-fit structures exhibits top-layer displacements normal to the surface characterized by a small bond-length-conserving, top-layer rotation (omega aproximately 2-3 deg), a small relaxation of the top layer away from the surface, and a 10 percent expansion of the top-layer bond length. The other region of best-fit structures is the conventional one: nearly bond-length-conserving rotations of omega = 26-28 deg in the top layer and a small (approximately 0.1 A) contraction of the uppermost layer spacing. This ambiguity may be removed, however, by consideration of the integrated beam intensities. The conventional region of structural parameters provides a decisively better description of the relative magnitudes of the integrated beam intensities and hence is the preferred structure.

A Novel, Diazonium-Phenolic Resin Two-Layer Resist System Utilizing Photoinduced Interfacial Insolubilization

NASA Astrophysics Data System (ADS)

Uchino, Shou-ichi; Iwayanagi, Takao; Ueno, Takumi; Hashimoto, Michiaki; Nonogaki, Saburo

1987-08-01

This paper deals with a negative two-layer photoresist system utilizing a photoinduced insolubilization process at the interface. The bottom layer is a phenolic resin either with or without aromatic azide and the top layer is a photosensitive layer comprised of an aromatic diazonium compound and a water soluble polymer. Upon exposure to light, the diazo compound decomposes to cause insolubilization at the interface between the two layers. The system exhibits high contrast due to the combination of interfacial insolubilization and contrast enhancement by photobleaching of the diazonium compound. Patterns of 0.5 um lines and spaces are obtained using an i-line stepper and a resist system containing 4-diazo-N,N-dimethylaniline chloride zinc chloride in the top layer and 3-(4-azidostyry1)- 5,5-dimethyl- 2-cyclohexen-1-one in the bottom layer. Resists with varying spectral responses from mid-UV to g-line can be designed by selecting the kind of diazo compound used in the top layer.

Compaction and sedimentary basin analysis on Mars

NASA Astrophysics Data System (ADS)

Gabasova, Leila R.; Kite, Edwin S.

2018-03-01

Many of the sedimentary basins of Mars show patterns of faults and off-horizontal layers that, if correctly understood, could serve as a key to basin history. Sediment compaction is a possible cause of these patterns. We quantified the possible role of differential sediment compaction for two Martian sedimentary basins: the sediment fill of Gunjur crater (which shows concentric graben), and the sediment fill of Gale crater (which shows outward-dipping layers). We assume that basement topography for these craters is similar to the present-day topography of complex craters that lack sediment infill. For Gunjur, we find that differential compaction produces maximum strains consistent with the locations of observed graben. For Gale, we were able to approximately reproduce the observed layer orientations measured from orbiter image-based digital terrain models, but only with a >3 km-thick donut-shaped past overburden. It is not immediately obvious what geologic processes could produce this shape.

InGaN laser diode with metal-free laser ridge using n+-GaN contact layers

NASA Astrophysics Data System (ADS)

Malinverni, Marco; Tardy, Camille; Rossetti, Marco; Castiglia, Antonino; Duelk, Marcus; Vélez, Christian; Martin, Denis; Grandjean, Nicolas

2016-06-01

We report on InGaN edge emitting laser diodes with a top metal electrode located beside the laser ridge. Current spreading over the ridge is achieved via a highly doped n+-type GaN layer deposited on top of the structure. The low sheet resistance of the n+-GaN layer ensures excellent lateral current spreading, while carrier injection is confined all along the ridge thanks to current tunneling at the interface between the n+-GaN top layer and the p++-GaN layer. Continuous-wave lasing at 400 nm with an output power of 100 mW is demonstrated on uncoated facet devices with a threshold current density of 2.4 kA·cm-2.

Salt flow direction and velocity during subsalt normal faulting and syn-kinematic sedimentation—implications from analytical calculations

NASA Astrophysics Data System (ADS)

Warsitzka, M.; Kukowski, N.; Kley, J.

2018-04-01

Salt flow induced by subsalt normal faulting is mainly controlled by tilting of the salt layer, the amount of differential loading due to syn-kinematic deposition, and tectonic shearing at the top or the base of the salt layer. Our study addresses the first two mechanisms and aims to examine salt flow patterns above a continuously moving subsalt normal fault and beneath a syn-kinematic minibasin. In such a setting, salt either tends to flow down towards the basin centre driven by its own weight or is squeezed up towards the footwall side owing to loading differences between the minibasin and the region above the footwall block. Applying isostatic balancing in analytical models, we calculated the steady-state flow velocity in a salt layer. This procedure gives insights into (1) the minimum vertical offset required for upward flow to occur, (2) the magnitude of the flow velocity, and (3) the average density of the supra-salt cover layer at the point at which upward flow starts. In a sensitivity study, we examined how the point of flow reversal and the velocity patterns are influenced by changes of the salt and cover layer thickness, the geometry of the cover flexure, the dip of the subsalt fault, compaction parameters of the supra-salt cover, the salt viscosity and the salt density. Our model results reveal that in most geological scenarios, salt flow above a continuously displacing subsalt normal fault goes through an early phase of downward flow. At sufficiently high fault offset in the range of 700-2600 m, salt is later squeezed upward towards the footwall side. This flow reversal occurs at smaller vertical fault displacement, if the thickness of the pre-kinematic layer is larger, the sedimentation rate of the syn-kinematic cover is higher, the compaction coefficient of cover sediments (i.e. the density increase with depth) is larger or the average density of the salt is lower. Other geometrical parameters such as the width of the cover monocline, the dip of the basement fault or the thickness of the salt layer have no significant influence on the point of reversal, but modify the velocity of the salt flow.

A numerical investigation of fine sediment resuspension in the wave boundary layer - effect of hindered settling and bedforms

NASA Astrophysics Data System (ADS)

Hsu, T. J.; Cheng, Z.; Yu, X.

2016-02-01

The wave bottom boundary layer is a major conduit delivering fine terrestrial sediments to the continental margin. Hence, studying the fine sediment resuspension in the wave boundary layer is crucial to the understanding of various components of the earth system, such as carbon cycle. By assuming the settling velocity to be a constant in each simulation, previous turbulence-resolving numerical simulations reveal the existence of three transport modes in the wave boundary layer associated with the sediment availability. As the sediment availability and hence the sediment-induced stable stratification increase, a sequence of transport modes, namely, (I) well-mixed transport, (II) formulation of lutocline resembling a two-layer system, and (III) completely laminarized transport are observed. In general, the settling velocity is a flow variable due to the floc dynamics and hindered settling. This study further investigate the effect of hindered settling. Particularly, for flocs with lower gelling concentrations, the hindered settling effect can play a key role in sustaining large amount of suspended sediment load and results in the laminarized transport (III). For the simulation with a very significant hindered settling effect due to a low gelling concentration, results also indicate the occurrence of gelling ignition, a state in which the erosion rate is always higher than the deposition rate. A condition for the occurrence of gelling ignition is proposed for a range of wave intensities as a function of sediment/floc properties and erodibility parameters. These aforementioned studies are limited to fine sediment transport over a flat bed. However, recent field and laboratory observation show that a small amount of sand fraction can lead to the formation of small bedforms, which can armor the bed while in the meantime enhance near bed turbulence. Preliminary investigation on the effect of bedforms on the resulting transport modes will also be presented.

Mixed sand and gravel beaches: accurate measurement of active layer depth and sediment transport volumes using PIT tagged tracer pebbles

NASA Astrophysics Data System (ADS)

Holland, A.; Moses, C.; Sear, D. A.; Cope, S.

2016-12-01

As sediments containing significant gravel portions are increasingly used for beach replenishment projects globally, the total number of beaches classified as `mixed sand and gravel' (MSG) increases. Calculations for required replenishment sediment volumes usually assume a uniform layer of sediment transport across and along the beach, but research into active layer (AL) depth has shown variations both across shore and according to sediment size distribution. This study addresses the need for more accurate calculations of sediment transport volumes on MSG beaches by using more precise measurements of AL depth and width, and virtual velocity of tracer pebbles. Variations in AL depth were measured along three main profile lines (from MHWS to MLWN) at Eastoke, Hayling Island (Hampshire, UK). Passive Integrated Transponder (PIT) tagged pebbles were deployed in columns, and their new locations repeatedly surveyed with RFID technology. These data were combined with daily dGPS beach profiles and sediment sampling for detailed analysis of the influence of beach morphodynamics on sediment transport volumes. Data were collected over two consecutive winter seasons: 2014-15 (relatively calm, average wave height <1 m) and 2015-16 (prolonged periods of moderate storminess, wave heights of 1-2 m). The active layer was, on average, 22% of wave height where beach slope (tanβ) is 0.1, with variations noted according to slope angle, sediment distribution, and beach groundwater level. High groundwater levels and a change in sediment proportions in the sandy lower foreshore reduced the AL to 10% of wave height in this area. The disparity in AL depth across the beach profile indicates that traditional models are not accurately representing bulk sediment transport on MSG beaches. It is anticipated that by improving model inputs, beach managers will be better able to predict necessary volumes and sediment grain size proportions of replenishment material for effective management of MSG beaches.

Metalliferous sediments from Eolo Seamount (Tyrrhenian Sea): Hydrothermal deposition and re-deposition in a zone of oxygen depletion

USGS Publications Warehouse

Dekov, V.M.; Kamenov, George D.; Savelli, C.; Stummeyer, Jens; Thiry, M.; Shanks, Wayne C.; Willingham, A.L.; Boycheva, T.B.; Rochette, P.; Kuzmann, E.; Fortin, D.; Vertes, A.

2009-01-01

A sediment core taken from the south-east slope of the Eolo Seamount is composed of alternating red-brown and light-brown to bluish-grey layers with signs of re-deposition in the middle-upper section. The red-brown layers are Fe-rich metalliferous sediments formed as a result of low-temperature (??? 77????C) hydrothermal discharge, whereas the bluish-grey layers most probably originated from background sedimentation of Al-rich detrital material. The metalliferous layers are composed mainly of Si-rich goethite containing some Al. Co-precipitation of hydrothermally released SiO44- and Fe2+ as amorphous or poorly crystalline Fe-Si-oxyhydroxides explains the high Si concentration in goethite. The elevated Al content of the goethite is fairly unusual, but reflects the extremely high background Al content of the Tyrrhenian seawater due to the high eolian terrigenous flux from the Sahara desert. The Sr and Nd isotope data suggest that the Eolo metalliferous sediments are the product of a 3-component mixture: hydrothermal fluid, seawater, and detrital material (Saharan dust and Aeolian Arc material). The enrichment in Fe, P, As, Mo, Cd, Be, Sb, W, Y, V, depletion in REE and transition elements (Cu, Co, Ni, Zn) and the REE distribution patterns support the low-temperature hydrothermal deposition of the metalliferous layers. The hydrothermal field is located in a seawater layer of relative O2 depletion, which led to a significant fractionation of the hydrothermally emitted Fe and Mn. Fe-oxyhydroxides precipitated immediately around the vents whereas Mn stayed in solution longer and the Mn-oxides precipitated higher up on the seamount slope in seawater with relatively higher O2 levels. High seismic activity led to sediment re-deposition and slumping of the Mn-rich layers down slope and mixing with the Fe-rich layers. ?? 2009 Elsevier B.V. All rights reserved.

Paint Removal from Composites and Protective Coating Development

DTIC Science & Technology

1991-01-01

bonds between these layers relax, and the removal of the top layer is facilitated. This phenomena is known as fracking . Cold Jet has completed an initial...sublimed carbon dioxide "atmosphere" and the top layer of material, so that fracking occurs. Cold Jet adds that removal tends to occur layer by layer...often removed faster (than thinner coatings) as a result of the fracking mechanism. The paint residue from the stripping process is comprised of varying

Accumulation of bank-top sediment on the western slope of Great Bahama Bank: rapid progradation of a carbonate megabank

USGS Publications Warehouse

Wilber, R. Jude; Milliman, John D.; Halley, Robert B.

1990-01-01

High-resolution seismic profiles and submersible observations along the leeward slope of western Great Bahama Bank show large-scale export of bank-top sediment and rapid progradation of the slope during the Holocene. A wedge-shaped sequence, up to 90 m thick, is present along most of the slope and consists of predominantly aragonite mud derived from the bank since flooding of the platform 6-8 ka. Total sediment volume of the slope sequence is 40%-80% that of Holocene sediment currently retained on the bank. Maximum rates of vertical accumulation and lateral progradation are 11-15 m/ka and 80-110 m/ka, respectively: 10 to 100 times greater than previously known for periplatform muds. Slope deposition of exported mud during sea-level highs appears to have been a major mechanism for the westward progradation of Great Bahama Bank throughout the Quaternary; this may provide a critical modern analogue for ancient progradational margins.

Crosslayer Survivability in Overlay-IP-WDM Networks

ERIC Educational Resources Information Center

Pacharintanakul, Peera

2010-01-01

As the Internet moves towards a three-layer architecture consisting of overlay networks on top of the IP network layer on top of WDM-based physical networks, incorporating the interaction between and among network layers is crucial for efficient and effective implementation of survivability. This dissertation has four major foci as follows:…

Thermodynamic Behavior of Nano-sized Gold Clusters on the (001) Surface

NASA Technical Reports Server (NTRS)

Paik, Sun M.; Yoo, Sung M.; Namkung, Min; Wincheski, Russell A.; Bushnell, Dennis M. (Technical Monitor)

2001-01-01

We have studied thermal expansion of the surface layers of the hexagonally reconstructed Au (001) surface using a classical Molecular Dynamics (MD) simulation technique with an Embedded Atomic Method (EAM) type many-body potential. We find that the top-most hexagonal layer contracts as temperature increases, whereas the second layer expands or contracts depending on the system size. The magnitude of expansion coefficient of the top layer is much larger than that of the other layers. The calculated thermal expansion coefficients of the top-most layer are about -4.93 x 10(exp -5)Angstroms/Kelvin for the (262 x 227)Angstrom cluster and -3.05 x 10(exp -5)Angstroms/Kelvin for (101 x 87)Angstrom cluster. The Fast Fourier Transform (FFT) image of the atomic density shows that there exists a rotated domain of the top-most hexagonal cluster with rotation angle close to 1 degree at temperature T less than 1000Kelvin. As the temperature increases this domain undergoes a surface orientational phase transition. These predictions are in good agreement with previous phenomenological theories and experimental studies.

Paleo-environments of Late Pliocene to Early Pleistocene Foreland-Basin Deposits in the Western Foothills of South-Central Taiwan

NASA Astrophysics Data System (ADS)

Chiu, Tzu-Hsuan; Tien-Shun Lin, Andrew; Chi, Wen-Rong; Wang, Shih-Wei

2017-04-01

Lithofacies and paleo-environmental analyses of the Pliocene-Pleistocene deposits of Taiwan provide a framework to understand the stratigraphic development of foreland basin to the west of the orogenic belt. In this study, we performed lithofacies analyses and biostratigraphic studies on calcareous nannofossils in two areas in south-central Taiwan, the Jhuoshuei River, and the Hushan Reservoir, respectively. The studied lithostratigraphic units are the Chinshui Shale, the Cholan Formation, and the Toukoshan Formation, in an ascending order, with a total stratigraphic thickness more than 3500 m in central Taiwan. Sixteen lithofacies and four lithofacies associations are identified, pertaining to tide-dominated deltaic systems bordering a shallow marine setting in the foreland basin. A few wide-spread layers of thickly-bedded sandstones featuring ball-and-pillow structures are interpreted as resulting from earthquake shaking (i.e., seismites). In addition, the vertical facies change shows a coarsening and shallowing-upward succession, indicating the gradually filling up of the foreland basin by sediment progradation. The progradation is interpreted to result from westward migrating orogenic belt and an increase in sediment supply. The top 2000-m thick foreland succession (i.e., the uppermost part of the Cholan Formation, and the Toukoshan Formation) is dominantly fluvial deposits with occasional intercalations of shoreface sediments, indicating an extremely rapid and balanced rate of basin subsidence and sediment supply for the past 1.5 Ma. Vertebrate fossils of deer and elephants are identified in the upper Cholan Formation deposited in coastal to fluvial settings. Keywords: Pliocene-Pleistocene Epoch, lithofacies, foreland basin, Taiwan

Estimating the free gas content in Baltic Sea sediments using compressional wave velocity from marine seismic data

NASA Astrophysics Data System (ADS)

Tóth, Zsuzsanna; Spiess, Volkhard; Mogollón, José M.; Jensen, Jørn Bo

2014-12-01

A 2-D high-resolution velocity field was obtained from marine seismic data to quantify free gas content in shallow muddy sediments at in situ pressure and temperature. The velocities were acquired applying Migration Velocity Analysis on prestack time-migrated data. Compressional wave velocities are highly sensitive to free gas as very small amounts of gas can cause a significant decrease in the medium velocity. The analyzed profile crosses a depression filled with organic-rich Holocene mud in the Bornholm Basin, Baltic Sea. The interval velocity field reveals two low-velocity patches, which extend from the reversed polarity reflections marking the top of the gassy sediment layer down to the base of the Holocene mud. Average interval velocities within the gassy mud are lower than the seafloor migration velocity by up to ˜500 m/s. This decrease, using a geoacoustic model, is caused by an average 0.046% gas volume fraction. The interval velocities in individual cells of the velocity field are reduced to ˜200 m/s predicting up to 3.4% gas content. The velocity field is limited in resolution due to velocity determination at and between reflections; however, together with the stratigraphic interpretation, geological units containing free gas could be identified. Shallow gas occurs vertically throughout most of the Holocene mud in the gassy area. Comparison with biogeochemical studies at other Baltic Sea sites suggests that the distribution of free gas is likely to be patchy in the sediment, but the gas concentration may peak below the sulfate-methane transition zone and gradually decrease below.

"Complexity" in Polarity Transitions at the Matuyama-Brunhes Boundary and top Jaramillo in North Atlantic Deep-sea Sediments

NASA Astrophysics Data System (ADS)

Channell, J. E. T.

2016-12-01

Integrated Ocean Drilling Program (IODP) Expedition 303 to the North Atlantic provided 16 records of the Matuyama-Brunhes polarity transition (MBT) and the top Jaramillo transition, based on u-channel and discrete samples, from holes drilled at three sites (Sites U1304, U1305 and U1306) that have mean Brunhes sedimentation rates of 16-18 cm/kyr. The MBT occurs during the transition from marine isotope stage (MIS) 19.3 to MIS 18.4, with mid-point at 773 ka, and a transition duration of 5-8 kyr. The top Jaramillo occurs during MIS 28 at 992 ka with a similar 5 kyr transition duration. Combining the new records with previously published North Atlantic records (ODP Sites 983, 984 and 1063) yields a total of 24 high sedimentation rate records. The MBT yields a repetitive pattern of transitional field states as virtual geomagnetic poles (VGPs) move from high southern latitudes to loop over the Pacific, cluster in NE Asia, and transit into the mid-latitude South Atlantic before reaching high latitudes in the Northern Hemisphere. The VGPs for the top Jaramillo transition feature a loop over the Pacific, then occupation of the NE Asia cluster before transit over the Indian Ocean to high southerly latitudes. The North Atlantic MBT records described here are very different to the longitudinally constrained North Atlantic VGP paths from MBT records that are the basis for a 2007 Bayesian inversion of the MBT field. We conclude that the relatively low sedimentation rate ( 4 cm/kyr) records utilized in the Bayesian inversion have been heavily smoothed by the remanence acquisition process, and do not adequately represent the MBT field. The VGPs at the MBT and top Jaramillo, as measured in the North Atlantic, have similarities with excursion (Iceland Basin) VGP paths, and are apparently guided by maxima in downward vertical flux in the modern non-dipole (ND) field, implying longevity in ND features through time.

Sediment tracing in the upper Hunter catchment using elemental and mineralogical compositions: Implications for catchment-scale suspended sediment (dis)connectivity and management

NASA Astrophysics Data System (ADS)

Fryirs, Kirstie; Gore, Damian

2013-07-01

River bed colmation layers clog the interstices of gravel-bed rivers, impeding the vertical exchange of water and nutrients that drives ecosystem function in the hyporheic zone. In catchments where fine-grained sediment supply has increased since human disturbance, understanding sediment provenance and the (dis)connectivity of supply allows practitioners to target sediment source problems and treat them within catchment management plans. Release of alluvial fine-grained sediment from channel bank erosion since European settlement has resulted in the formation of a colmation layer along the upper Hunter River at Muswellbrook, eastern Australia. X-ray fluorescence spectrometry (XRF) and X-ray diffractometry (XRD) are used to determine the elemental and mineralogical signatures of colmation layer and floodplain sediment sources across this 4480 km2 catchment. This sediment tracing technique is used to construct a picture of how suspended sediment supply and (dis)connectivity operates in this catchment. In this system, the primary source areas are subcatchments in which sediments are stored largely in partly confined floodplain pockets, but from which sediment supply is unimpeded and directly connected to the receiving reach. Subcatchments in which alluvial sediment storage is significant — and which contain large, laterally unconfined valleys — are essentially 'switched off' or disconnected from the receiving reach. This is because large sediment sinks act to trap fine-grained sediment before it reaches the receiving reach, forming a buffer along the sediment conveyor belt. Given the age structure of floodplains in the receiving reach, this pattern of source area contributions and (dis)connectivity must have occurred throughout the Holocene.

Possible Mud Cracks Preserved in Martian Rock

NASA Image and Video Library

2017-01-17

The network of cracks in this Martian rock slab called "Old Soaker" may have formed from the drying of a mud layer more than 3 billion years ago. The view spans about 4 feet (1.2 meters) left-to-right and combines three images taken by the Mars Hand Lens Imager (MAHLI) camera on the arm of NASA's Curiosity Mars rover. Mud cracks would be evidence of a time when dry intervals interrupted wetter periods that supported lakes in the area. Curiosity has found evidence of ancient lakes in older, lower-lying rock layers and also in younger mudstone that is above Old Soaker. MAHLI was positioned about 3 feet (90 centimeters) above the surface when it took the component images on Dec. 31, 2016, during the 1,566th Martian day, or sol, of Curiosity's work on Mars. This observation was planned as part of assessing a hypothesis that the target preserves evidence of drying mud. The location is within an exposure of Murray formation mudstone on lower Mount Sharp inside Gale Crater. The slab bears a network of four- and five-sided polygons about half an inch to 1 inch (1 to 2 centimeters) across, which matches the pattern commonly formed when a thin layer of mud dries. Some edges of the polygons are ridges of material the same color as the surrounding rock. This could result from a three-step process after cracks form due to drying: Wind-blown sediments accumulate in the open cracks. Later, these sediments and the dried mud become rock under the pressure of multiple younger layers that accumulate on top of them. Most recently, after the overlying layers were eroded away by wind, the vein-filling material resists erosion better than the once-muddy material, so the pattern that began as cracks appears as ridges. Note that some of the cracks contain material much brighter than the surrounding rock. These are mineral veins. Curiosity has found such bright veins of calcium sulfate in many rock layers the rover has investigated. These veins form from circulation of mineral-laden groundwater through underground cracks. Rover-team scientists suggest that a likely scenario for the history of Old Soaker is more than one generation of fracturing: mud cracks first, with sediment accumulating in them, then a later episode of underground fracturing and vein forming. The target rock's name comes from the name of an island off the coast of Maine. The names informally assigned by the rover team to features in the area of lower Mount Sharp that includes this slab are from a list of islands, hills and other sites in or near Maine's Bar Harbor. http://photojournal.jpl.nasa.gov/catalog/PIA21261

Geochemistry and microbiology at gas hydrate and mud volcano sites in the black sea

NASA Astrophysics Data System (ADS)

Drews, M.; Schmaljohann, R.; Wallmann, K.

2003-04-01

We present geochemical and microbiological results which were obtained from sediments at gas hydrate and mud volcano sites in the Sorokin Trough (northern Black Sea, south east of the Crimean peninsula) at water depths of about 1800 to 2100 m during the METEOR cruise 52-1. The surface near sub-bottom accumulations of gas hydrates (occuring at depths of several meters or less beneath the sea floor) in the Black Sea are associated with numerous mud volcanos. At stations we investigated gas hydrates occurred below 10 cm to 100 cm with a significant influence on the sediment biochemistry. Analyses revealed high methane concentrations, anoxic and sulfidic conditions, a steep sulfate gradient, carbonate precipitation, and high anaerobic methane oxidation rates. In proximity of the so called Odessa mud volcano one investigated sampling station showed maximum methane oxidation rates in the depth horizon of a firm 2 cm thick carbonate crust layer, adhered to by a bacterial mat. This observation is taken to indicate that the bacteria are causing or mediating the crust formation by their anaerobic methane oxidation metabolism. The station was further characterised by two layers of gas hydrate fragments and lenses below 1 m depth. A 2 to 4 cm thick carbonate crust with attached bacterial mat from a Yalta mud vulcano sample (2124 m water depth) was investigated under the scanning electron microscope. The stiff gelatinous mat showed a dense and morphologically uniform population of rod shaped bacteria with only a few nests of coccoid cells. Purified mat material exhibited anaerobic methane oxidation activity. These mats resemble the type previously found in the shallow NW methane seep area of the Black Sea, where it covers carbonate chimneys. Samples from two sites atop the summit of the active but flat-topped Dvurechenskii mud volcano were characterised by very high methane oxidation rates (up to 563 nmol/cm3/d) at the sediment surface. Strong pore water gradients of chloride, bromide, ammonium, methane, and temperature proved the existence of a rich upward flow of warm fluids from the deeper sediment. At both stations no carbonate crusts or bacterial mats were found. The lack of hemipelagic sediments and at the same time abundance of mud breccia gives ample evidence of the recency of the mud flow.

Ill-posedness in modeling mixed sediment river morphodynamics

NASA Astrophysics Data System (ADS)

Chavarrías, Víctor; Stecca, Guglielmo; Blom, Astrid

2018-04-01

In this paper we analyze the Hirano active layer model used in mixed sediment river morphodynamics concerning its ill-posedness. Ill-posedness causes the solution to be unstable to short-wave perturbations. This implies that the solution presents spurious oscillations, the amplitude of which depends on the domain discretization. Ill-posedness not only produces physically unrealistic results but may also cause failure of numerical simulations. By considering a two-fraction sediment mixture we obtain analytical expressions for the mathematical characterization of the model. Using these we show that the ill-posed domain is larger than what was found in previous analyses, not only comprising cases of bed degradation into a substrate finer than the active layer but also in aggradational cases. Furthermore, by analyzing a three-fraction model we observe ill-posedness under conditions of bed degradation into a coarse substrate. We observe that oscillations in the numerical solution of ill-posed simulations grow until the model becomes well-posed, as the spurious mixing of the active layer sediment and substrate sediment acts as a regularization mechanism. Finally we conduct an eigenstructure analysis of a simplified vertically continuous model for mixed sediment for which we show that ill-posedness occurs in a wider range of conditions than the active layer model.

Regional-scale input of dispersed and discrete volcanic ash to the Izu-Bonin and Mariana subduction zones

NASA Astrophysics Data System (ADS)

Scudder, Rachel P.; Murray, Richard W.; Schindlbeck, Julie C.; Kutterolf, Steffen; Hauff, Folkmar; McKinley, Claire C.

2014-11-01

We have geochemically and statistically characterized bulk marine sediment and ash layers at Ocean Drilling Program Site 1149 (Izu-Bonin Arc) and Deep Sea Drilling Project Site 52 (Mariana Arc), and have quantified that multiple dispersed ash sources collectively comprise ˜30-35% of the hemipelagic sediment mass entering the Izu-Bonin-Mariana subduction system. Multivariate statistical analyses indicate that the bulk sediment at Site 1149 is a mixture of Chinese Loess, a second compositionally distinct eolian source, a dispersed mafic ash, and a dispersed felsic ash. We interpret the source of these ashes as, respectively, being basalt from the Izu-Bonin Front Arc (IBFA) and rhyolite from the Honshu Arc. Sr-, Nd-, and Pb isotopic analyses of the bulk sediment are consistent with the chemical/statistical-based interpretations. Comparison of the mass accumulation rate of the dispersed ash component to discrete ash layer parameters (thickness, sedimentation rate, and number of layers) suggests that eruption frequency, rather than eruption size, drives the dispersed ash record. At Site 52, the geochemistry and statistical modeling indicates that Chinese Loess, IBFA, dispersed BNN (boninite from Izu-Bonin), and a dispersed felsic ash of unknown origin are the sources. At Site 1149, the ash layers and the dispersed ash are compositionally coupled, whereas at Site 52 they are decoupled in that there are no boninite layers, yet boninite is dispersed within the sediment. Changes in the volcanic and eolian inputs through time indicate strong arc-related and climate-related controls.

Identification of in-sewer sources of organic solids contributing to combined sewer overflows.

PubMed

Ahyerre, M; Chebbo, G

2002-09-01

Previous research has shown that combined sewer systems are the main source of particle and organic pollution during rainfall events contributing to combined sewer overflow. The aim of this article is to identify in an urban catchment area called "Le Marais", in the center of Paris, the types of sediments that are eroded and contribute to the pollution of combined sewer overflow. Three sediment types are considered: granular material found in the inverts of pipes, organic biofilms and organic sediment at the water bed interface, identified as an immobile layer in the "Le Marais" catchment area. The method used consist, firstly, of sampling and assessing the organic pollutant loads and metallic loads of the particles in each type of sediment. Then, the mass of each type of sediment is assessed. The mass and the characteristics of each type of sediment is finally compared to the mass and characteristics of the particles eroded in the catchment area, estimated by mass balances, in order to find the source of eroded particles. The only identified type of deposit that can contribute to combined sewer overflows is the organic layer. Indeed, the solids of this layer have mean and metallic loads that are of the same order of magnitude as the eroded particles. Moreover, the mass of the organic layer considered over different time scales is of the same order of magnitude as the eroded masses during rainfall events and an erosion experiment showed that the organic layer is actually eroded.

A Possible Origin of the Gas Hydrate in Southwest Taiwan Offshore Area

NASA Astrophysics Data System (ADS)

Lee, C.; Lee, J.; Oung, J.

2003-12-01

The southwest Taiwan locate at the eastward subduction zone of the Eurasian plate, which is currently converging with the Philippine Sea plate at a rate of several few centimeters per year. The geological setting of this region is characterized by the appearance of thick accreted sediments up to several kilometers, numerous submarine canyons, active faults, and mud diapirs/volcanoes. The origin of mud diapir/volcano is probably related to the plate convergence. During the tectonic processes, the organic matters were "cooked" thermogenically and biogenically to produce the natural gases, and possibly the oil in the sediment. Beneath the seafloor, if the natural gases were at the appropriate temperature and pressure condition, they would become the gas hydrate, and preserved in the top sediment layers. The formation of gas hydrate is situated under the water depth at about 300 to 3000 meters in this region. In the seismic profiles, the Bottom Simulation Reflector (BSR) probably represents the boundary between the solid-state and gas-state natural gas. The BSR is also regarded as an important marker as an existence of gas hydrate. It is extensively distributed in the continental margin off southwest Taiwan, but unstable, especially along the active fault zones. The natural gas as well as the mud and hydraulic fluid in the deep sediment are pushed into the surface layer. In order to investigate the relationship between mud diapir and gas hydrate, we conduct the geophysical and geological methods: using a 38/150 kHz high-frequency echo sounder system to guide and select the sites for mud diapirs, and take 1-3 m gravity core samples. We, then, adopt an up-side-down "headspace" tin-can technique to preserve the gases, and use a gas chromatography to analyze its contents. Oil companies commonly use the method. The first result shows that the existence of methane, ethane, propane and possible other higher hydrocarbon contents in the core samples. The methane is the most abundant gas, up to 1859 parts per million in volume (ppm); the others are not significant, probably due to a leaking in the sampling and transportation. We have reduced the "headspace" in order to preserve more concentrated gases in the second attempt, and the result shows similar. Nonetheless, our results suggest that the gases are probably a mixture of thermogenic and biogenic origin. Due to the existence of higher hydrocarbon contents, we believe that the thermogenic gases are produced in the deep source sediments, while the shallow biogenic methane is mixing with them in the top sediment. In the mud diapir/volcano area, the contents of natural gases are usually higher than that in a flat seafloor. As several high gas values have been founded in the near shore area (e.g., 1604 ppm of C1 plus C2 and C3 found at a water depth of 23 m), we suggest that the 300-3000 m gas hydrate zone is probably in a dynamic balance of which the deep gases are continuously migrating to the BSR and the free gases are being evaporating from this zone. Our data illustrate the potential existence of natural gases in this region; however, we cannot quantify the reserve at this time. Further investigations with a long core and better-improved techniques are needed.

Rethinking Recycling in Arcs

NASA Astrophysics Data System (ADS)

Kelemen, P.; Behn, M. D.; Jagoutz, O.

2012-12-01

Hacker et al EPSL 2011 and Behn et al Nature Geosci 2011 investigated pathways for return of buoyant, subducted material to arc crust. These include (1) diapirs rising into the hot mantle wedge, with extensive melts adding a component to arc magmas, (2) flow of material back up a relatively cold "subduction channel", adding solids to the lower crust and small-degree partial melts to the upper crust, (3) flow from the forearc along the base of arc crust, and (4) imbrication of forearc material into arc crust. These processes add felsic, incompatible-element-rich components to arc crust. The flux of incompatible elements such as Th in arc lavas, thought to be mainly recycled from subducted sediments, is > sediment subduction flux. There are large uncertainties: arc crustal growth rates are imprecise; young, primitive arc lavas may not be representative of magmatic flux into arc crust; sediment subduction flux may have varied. Nevertheless, this result is found for all arcs examined, using recently published growth rates. Perhaps arc growth rates that include subduction erosion are systematically overestimated. Instead or in addition, maybe significant Th comes from material other than sediments. Here, we consider the implications of pathways 1-4 for arc growth rates and incompatible element enrichment, in the context of subduction erosion and arc-arc collision. Subducting arc lithologies can become separated, with only felsic components returned to arc crust. Buoyant lithologies are mobile in viscous instabilities at > 700-800°C. Whereas thin layers such as sediments may become mobile all at once, instabilities may periodically strip the hottest parts from the top of thick buoyant layers, replacing them with hot mantle. In arc-arc collision, the top of a subducting plate starts at about 0°C on the seafloor, so heating is slow. In subduction erosion, forearc material in the subducting package can be > 200°C before erosion so buoyant lithologies reach 700-800°C faster, and in larger volumes at a given time. Subduction erosion rarely, if ever, transports significant amounts of buoyant material deep into the convecting mantle. Because buoyant material can remain part of the crust, it may often be a mistake to add all of the eroded material to the observed arc volume to derive crustal growth rates. Buoyancy instabilities during subduction erosion or arc-arc collision will accumulate felsic arc crust. For example, > 50% of Aleutian arc lavas and exposed plutons are more buoyant than mantle peridotite at 700-800°C, 3-4 GPa. The buoyant material has an average of 60-62 wt% SiO2, molar Mg/(Mg+Fe) 0.4-0.5, and trace elements identical to bulk continental crust, though western Aleutian lavas have the most depleted Sr, Nd and Pb isotope ratios of all arc lavas worldwide. In general, density sorting of arc lithologies, and subsequent partial melting as buoyant rocks rise through the mantle wedge or along a subduction channel, could lead to a kind of double and triple distillation. Incompatible elements such as Th would be enriched in arc crust, retaining correlations with isotopic indicators of a recycled sediment component, while Th-poor, dense, mafic lavas and lower crustal cumulates return to the convecting mantle.

Large-Eddy Simulation in Planetary Boundary-Layer Research

NASA Technical Reports Server (NTRS)

Wyngaard, J. C.

1985-01-01

The structure and dynamics of the convective boundary layer are discussed. The vertical transport of a conservative, passive scalar was simulated. Also studied were the statistics by top-down and bottom-up scalar fields. Substantial differences were found between them due, presumably, to the asymmetry in the convective boundary layer. A generalization of mixed-layer scaling was developed which allows one to include the effects of top-down diffusion.

δ13C and δ15N Values of Sediment-trap Particles in the Japan and Yamato Basins and Comparison with the Core-top Values in the East/Japan Sea

NASA Astrophysics Data System (ADS)

Khim, Boo-Keun; Otosaka, Shigeyoshi; Park, Kyung-Ae; Noriki, Shinichiro

2018-03-01

Investigation of sediment-trap deployments in the East/Japan Sea (EJS) showed that distinct seasonal variations in particulate organic carbon (POC) fluxes of intermediate-water sediment-traps clearly corresponded to changes in chlorophyll a concentrations estimated from SeaWiFS data. The prominent high POC flux periods (e.g., March) were strongly correlated with the enhanced surface-water phytoplankton blooms. Deep-water sedimenttraps exhibited similar variation patterns to intermediate-water sediment-traps. However, their total flux and POC flux were higher than those of intermediate-water sediment-traps during some months (e.g., April and May), indicating the lateral delivery of some particles to the deep-water sediment-traps. Distinct seasonal δ13C and δ15N variations in settling particles of the intermediate-water sediment-traps were observed, strongly supporting the notion of seasonal primary production. Seasonal variations in δ13C and δ15N values from the deep-water sediment-traps were similar to those of the intermediate-water sediment-traps. However, the difference in δ13C and δ15N values between the intermediate-water and the deepwater sediment-traps may be attributed to degradation of organic matter as it sank through the water column. Comparison of fluxweighted δ13C and δ15N mean values between the deep-water sediment-traps and the core-top sediments showed that strong selective loss of organic matter components (lipids) depleted in 13C and 15N occurred during sediment burial. Nonetheless, the results of our study indicate that particles in the deep-water sediment-trap deposited as surface sediments on the seafloor preserve the record of surface-water conditions, highlighting the usefulness of sedimentary δ13C and δ15N values as a paleoceanographic application in the EJS.

Influence of sediment-organic matter quality on growth and polychlorobiphenyl bioavailability in Echinodermata (Amphiura filiformis)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunnarsson, J.S.; Granberg, M.E.; Nilsson, H.C.

Sediment total organic carbon (TOC) content is considered to be a primary food source for benthic invertebrates and a major factor influencing the partitioning and bioavailability of sediment-associated organic contaminants. Most studies report that both toxicity and uptake of sediment-associated contaminants by benthic organisms are inversely proportional to sediment TOC content. The aim of this study was to determine the importance of the TOC quality for the bioavailability of sediment-associated organic contaminants and the growth of benthic macrofauna. The common infaunal brittle star Amphiura filiformis was exposed to a base sediment covered by a {sup 14}C-polychlorobipenyl (3,3{prime}4,4{prime}-{sup 14}C-tetrachlorobiphenyl (TCB)) contaminatedmore » top layer (0--2 cm), enriched to the same TOC content with 31 g TOC/m{sup 2} of different quality and origin. The following carbon sources, ranging from labile to refractory, were used: (1) green macroalga (Ulva lactuca), (2) brown macroalga (Ascophyllum nodosum), (3) eelgrass (Zostera Marina), (4) phytoplankton (Ceratium spp.), and (5) lignins of terrestrial origin. Characterization of the organic matter quality was accomplished by measuring the content of amino acids, lipids, C, N, and polyphenolic compounds. The reactivity of the sedimentary organic matter was assessed by means of respiration and dissolved inorganic nitrogen flux measurements. The experiment was carried out in 1-L glass jars, each containing four brittle stars and the contaminated and enriched sediment. The jars were circulated in a flow-through mode with filtered seawater. Somatic growth (regeneration of a precut arm) and bioaccumulation of {sup 14}C-TCB were measured at 10 sampling occasions during 48 d of exposure. Growth rates, TCB uptake rates, and steady-state concentrations differed significantly between treatments and were correlated to the qualities of the organic substrates. The greatest TCB accumulation and growth were observed in treatments with the most labile organic substrates and the lowest accumulation and growth were seen with the most refractory substrates. Results from this experiment suggest that the bioaccumulation of organic contaminants in benthic infauna is dependent on the nutritional quality of the sedimentary organic matter.« less

Field Validation of Molybdenum Accumulation as an Indicator of Hypoxic Water Conditions

EPA Science Inventory

Laboratory experiments have shown that the accumulation rate of authigenic molybdenum (Mo) in marine sediments may serve as a quantitative surrogate for direct measurement of hypoxic conditions in overlying waters: Mo accumulation in the top 1 cm of sediment is linearly related t...

Tuning SPT-3G Transition-Edge-Sensor Electrical Properties with a Four-Layer Ti-Au-Ti-Au Thin-Film Stack

NASA Astrophysics Data System (ADS)

Carter, F. W.; Ade, P. A. R.; Ahmed, Z.; Anderson, A. J.; Austermann, J. E.; Avva, J. S.; Thakur, R. Basu; Bender, A. N.; Benson, B. A.; Carlstrom, J. E.; Cecil, T.; Chang, C. L.; Cliche, J. F.; Cukierman, A.; Denison, E. V.; de Haan, T.; Ding, J.; Divan, R.; Dobbs, M. A.; Dutcher, D.; Everett, W.; Foster, A.; Gannon, R. N.; Gilbert, A.; Groh, J. C.; Halverson, N. W.; Harke-Hosemann, A. H.; Harrington, N. L.; Henning, J. W.; Hilton, G. C.; Holzapfel, W. L.; Huang, N.; Irwin, K. D.; Jeong, O. B.; Jonas, M.; Khaire, T.; Kofman, A. M.; Korman, M.; Kubik, D.; Kuhlmann, S.; Kuo, C. L.; Kutepova, V.; Lee, A. T.; Lowitz, A. E.; Meyer, S. S.; Michalik, D.; Miller, C. S.; Montgomery, J.; Nadolski, A.; Natoli, T.; Nguyen, H.; Noble, G. I.; Novosad, V.; Padin, S.; Pan, Z.; Pearson, J.; Posada, C. M.; Rahlin, A.; Ruhl, J. E.; Saunders, L. J.; Sayre, J. T.; Shirley, I.; Shirokoff, E.; Smecher, G.; Sobrin, J. A.; Stan, L.; Stark, A. A.; Story, K. T.; Suzuki, A.; Tang, Q. Y.; Thompson, K. L.; Tucker, C.; Vale, L. R.; Vanderlinde, K.; Vieira, J. D.; Wang, G.; Whitehorn, N.; Yefremenko, V.; Yoon, K. W.; Young, M. R.

2018-04-01

We have developed superconducting Ti transition-edge sensors with Au protection layers on the top and bottom for the South Pole Telescope's third-generation receiver (a cosmic microwave background polarimeter, due to be upgraded this austral summer of 2017/2018). The base Au layer (deposited on a thin Ti glue layer) isolates the Ti from any substrate effects; the top Au layer protects the Ti from oxidation during processing and subsequent use of the sensors. We control the transition temperature and normal resistance of the sensors by varying the sensor width and the relative thicknesses of the Ti and Au layers. The transition temperature is roughly six times more sensitive to the thickness of the base Au layer than to that of the top Au layer. The normal resistance is inversely proportional to sensor width for any given film configuration. For widths greater than five micrometers, the critical temperature is independent of width.

Bi-layered nanocomposite bandages for controlling microbial infections and overproduction of matrix metalloproteinase activity.

PubMed

Anjana, J; Mohandas, Annapoorna; Seethalakshmy, S; Suresh, Maneesha K; Menon, Riju; Biswas, Raja; Jayakumar, R

2018-04-15

Chronic diabetic wounds is characterised by increased microbial contamination and overproduction of matrix metalloproteases that would degrade the extracellular matrix. A bi-layer bandage was developed, that promotes the inhibition of microbial infections and matrix metalloprotease (MMPs) activity. Bi-layer bandage containing benzalkonium chloride loaded gelatin nanoparticles (BZK GNPs) in chitosan-Hyaluronic acid (HA) as a bottom layer and sodium alendronate containing chitosan as top layer was developed. We hypothesized that the chitosan-gelatin top layer with sodium alendronate could inhibit the MMPs activity, whereas the chitosan-HA bottom layer with BZK GNPs (240±66nm) would enable the elimination of microbes. The porosity, swelling and degradation nature of the prepared Bi-layered bandage was studied. The bottom layer could degrade within 4days whereas the top layer remained upto 7days. The antimicrobial activity of the BZK NPs loaded bandage was determined using normal and clinical strains. Gelatin zymography shows that the proteolytic activity of MMP was inhibited by the bandage. Copyright © 2017 Elsevier B.V. All rights reserved.

Scaling oxygen microprofiles at the sediment interface of deep stratified waters

NASA Astrophysics Data System (ADS)

Schwefel, Robert; Hondzo, Miki; Wüest, Alfred; Bouffard, Damien

2017-02-01

Dissolved oxygen microprofiles at the sediment-water interface of Lake Geneva were measured concurrently with velocities 0.25 to 2 m above the sediment. The measurements and scaling analyses indicate dissolved oxygen fluctuations and turbulent fluxes in exceedance of molecular diffusion in the proximity of the sediment-water interface. The measurements allowed the parameterization of the turbulent diffusion as a function of the dimensionless height above the sediment and the turbulence above the sediment-water interface. Turbulent diffusion depended strongly on the friction velocity and differed from formulations reported in the literature that are based on concepts of turbulent and developed wall-bounded flows. The dissolved oxygen microprofiles and proposed parameterization of turbulent diffusion enable a foundation for the similarity scaling of oxygen microprofiles in proximity to the sediment. The proposed scaling allows the estimation of diffusive boundary layer thickness, oxygen flux, and oxygen microprofile distribution in the near-sediment boundary layer.

Historical record of mercury contamination in sediments from the Babeni Reservoir in the Olt River, Romania.

PubMed

Bravo, Andrea Garcia; Loizeau, Jean-Luc; Ancey, Lydie; Ungureanu, Viorel Gheorghe; Dominik, Janusz

2009-08-01

Mercury (Hg) is a ubiquitous and hazardous contaminant in the aquatic environment showing a strong biomagnification effect along the food chain. The most common transfer path of Hg to humans is contaminated fish consumption. In severely exposed humans, Hg poisoning may lead to damage in the central nervous system. Thus, it is important to examine current and past contamination levels of Hg in aquatic milieu. The Olt River is the largest Romanian tributary of the Danube River. The use of Hg as an electrode in a chlor-alkali plant contributed to the contamination of the aquatic environment in the Rm Valcea region. The purpose of this study was to compare the current state of Hg contamination with the past contamination using a historical record obtained from a dated sediment core from one of the Olt River reservoirs (Babeni) located downstream from the chlor-alkali plant. To our knowledge, no published data on Hg contamination in this region are available. The Babeni Reservoir was selected for this study because it is situated downstream from the chlor-alkali plant, whilst the other reservoirs only retain the pollutants coming from the upstream part of the watershed. Preliminary analyses (unpublished) showed high Hg concentrations in the surface sediment of the Babeni Reservoir. One core was taken in the upstream Valcea Reservoir to provide a local background level of Hg concentrations in sediments. Sediment texture was uniform in the cores from both reservoirs. Laminated sediment structure, without any obvious discontinuities, was observed. Hg concentrations in the sediment core from the Valcea Reservoir were low and constant (0.01-0.08 mg/kg). In Babeni Reservoir sediments, Hg concentrations were very high in the deeper core section (up to 45 mg/kg in the longest core) and decreased to lower concentrations toward the top of the cores (1.3-2.4 mg/kg). This decrease probably reflects technological progress in control of emissions from the Hg-cell-based chlor-alkali industry. Two strong peaks could be distinguished in older sediments. The mean rate of sedimentation (5.9 cm/year) was calculated from the depth of the (137)Cs Chernobyl peak. This was in good agreement with the sedimentation rate estimated at this site from a bathymetric study. Assuming a constant sedimentation rate, the two Hg peaks would reflect two contamination events in 1987 and 1991, respectively. However, it is also possible that the two peaks belong to the same contamination event in 1987 but were separated by a sediment layer richer in sand and silt. This layer had a low Hg concentration, which can be interpreted as a mass deposition event related to a major flood bringing Hg-free sediments. Whilst the chlor-alkali plant partly switched to a cleaner technology in 1999, no obvious decrease of Hg concentrations was observed in recent decade. Results from the sediment core reflected the historical trend of Hg release from the chlor-alkali plant, revealed important contamination episodes and confirmed a legacy of contamination of Hg in recent sediments even if the concentrations of Hg decreased toward the surface due to a more efficient emission control. Although the Hg concentrations in Babeni Reservoir sediments were extremely high in the late eighties and they remain one order of magnitude higher in the surface sediments than in sediments from the upstream reservoir, little is known about the transfer of Hg to the biota and human population. Our initial measurements indicate the presence of monomethyl-Hg (MMHg) in pore water, but further studies are necessary to evaluate fluxes of MMHg at the sediment-water interface. Samples of fish and hair from various groups of the local population were recently collected to evaluate the potential hazard of Hg contamination to human health in the Rm Valcea region.

Microbial diversity in methane hydrate-bearing deep marine sediments core preserved in the original pressure.

NASA Astrophysics Data System (ADS)

Takahashi, Y.; Hata, T.; Nishida, H.

2017-12-01

In normal coring of deep marine sediments, the sampled cores are exposed to the pressure of the atmosphere, which results in dissociation of gas-hydrates and might change microbial diversity. In this study, we analyzed microbial composition in methane hydrate-bearing sediment core sampled and preserved by Hybrid-PCS (Pressure Coring System). We sliced core into three layers; (i) outside layer, which were most affected by drilling fluids, (ii) middle layer, and (iii) inner layer, which were expected to be most preserved as the original state. From each layer, we directly extracted DNA, and amplified V3-V4 region of 16S rRNA gene. We determined at least 5000 of nucleotide sequences of the partial 16S rDNA from each layer by Miseq (Illumina). In the all layers, facultative anaerobes, which can grow with or without oxygen because they can metabolize energy aerobically or anaerobically, were detected as majority. However, the genera which are often detected anaerobic environment is abundant in the inner layer compared to the outside layer, indicating that condition of drilling and preservation affect the microbial composition in the deep marine sediment core. This study was conducted as a part of the activity of the Research Consortium for Methane Hydrate Resources in Japan [MH21 consortium], and supported by JOGMEC (Japan Oil, Gas and Metals National Corporation). The sample was provided by AIST (National Institute of Advanced Industrial Science and Technology).

Geochemistry driven trends in microbial diversity and function across a temperature transect of a shallow water hydrothermal system off Milos (Greece)

NASA Astrophysics Data System (ADS)

Bühring, Solveig I.; Amend, Jan P.; Gómez Sáez, Gonzalo V.; Häusler, Stefan; Hinrichs, Kai-Uwe; Pichler, Thomas; Pop Ristova, Petra; Price, Roy E.; Santi, Ioulia; Sollich, Miriam

2014-05-01

The shallow water hydrothermal vents off Milos Island, Greece, discharge hot, slightly acidic, reduced fluids into colder, slightly alkaline, oxygenated seawater. Gradients in temperature, pH, and geochemistry are established as the two fluids mix, leading to the formation of various microbial microniches. In contrast to deep-sea hydrothermal systems, the availability of sun light allows for a combination of photo- and chemotrophic carbon fixation. Despite the comparably easy accessibility of shallow water hydrothermal systems, little is known about their microbial diversity and functioning. We present data from a shallow hydrothermal system off Milos Island, one of the most hydrothermally active regions in the Mediterranean Sea. The physico-chemical changes from ambient seafloor to hydrothermal area were investigated and documented by in situ microsensor profiling of temperature, pH, total reduced sulfur and dissolved oxygen alongside porewater geochemistry. The spatial microbial diversity was determined using a combination of gene- and lipid-based approaches, whereas microbial functioning was assessed by stable isotope probing experiments targeting lipid biomarkers. In situ microprofiles indicated an extreme environment with steep gradients, offering a variety of microniches for metabolically diverse microbial communities. We sampled a transect along a hydrothermal patch, following an increase in sediment surface temperature from background to 90°C, including five sampling points up to 20 cm sediment depth. Investigation of the bacterial diversity using ARISA revealed differences in the community structure along the geochemical gradients, with the least similarity between the ambient and highly hydrothermally impacted sites. Furthermore, using multivariate statistical analyses it was shown that variations in the community structure could be attributed to differences in the sediment geochemistry and especially the sulfide content, and only indirectly to shifts in temperature. Results from intact polar lipid analyses were consistent with the ARISA data and clearly differentiated those samples located close to the vent from those found in less affected areas. Changes from phospho- and betaine lipids within the top layer of the unaffected area to glyco- and ornithine lipids in the hydrothermally influenced sediment layers reflected a change from photoautotrophic algae to a bacteria-dominated community as predominant lipid sources. A clear dominance of archaeal lipids indicated archaea as key players in the deeper, hotter layers of the hydrothermal sediment. We performed stable isotope probing experiments with 13C-bicarbonate in the dark to investigate if chemolithotrophy, as opposed to phototrophy, plays any significant role for carbon fixation in shallow vent systems. Different amendments revealed that not only chemolithotrophy represents an important pathway for carbon fixation in these ecosystems, but that diverse ways of dark CO2 fixation exist, with hydrogen being the most effective electron donor under high temperature conditions.

The influence of buried nodules on the mobility of metals in deep sea sediments

NASA Astrophysics Data System (ADS)

Heller, Christina; Kuhn, Thomas

2017-04-01

Hydrothermal fluids can extract significant amounts of heat from oceanic lithosphere by lateral fluid flow through permeable basaltic crust of an age of up to 65 Ma. Fluid recharge and discharge occur at basement outcrops in between impermeable pelagic deep sea sediments. Recharge of oxic seawater causes upward oxygen diffusion into sediments overlying the permeable basalt in areas proximal to recharge sites. It is suggested that this oxygen has a strong impact on sediments and Mn-nodules during fluid exposure time. The aim of this study is to investigate if/how fluid flow through oceanic crust influence the distribution and element budget of Mn-nodules. Nodules occur widespread at the seafloor of the Clarion-Clipperton Zone (CCZ) in the equatorial North Pacific and were analyzed in many studies worldwide. Nodules buried in the deep sea sediments could be found only rarely (von Stackelberg, 1997, Geol. Soc. Spec. Publ., 119: 153-176). High resolution side-scan sonar recordings (unpublished Data BGR Hannover) indicate that there exist a coherent layer of nodules buried in the sediments of the working area. During the expedition SO 240/FLUM nodules were found on the sediment surface in 4200 to 4300 m water depth as well as in the sediment down to 985 cm below seafloor. In general, nodules consist of different nm- to µm-thick, dense and porous layers. The geochemical composition of bulk nodules and single nodule layers were determined by XRF, ICP-MS/OES, XRD and by high resolution analyses with electron microprobe and LA-ICP-MS. Dense layers have low Mn/Fe ratios (<4) and high concentrations of Co, Zr and REY, while porous layers are characterized by high Mn/Fe ratios (> 10) and high Ni+Cu and Li concentrations. The different compositions depend on different formation processes of the layers. They were formed by metal precipitation from oxic (hydrogenetic) and suboxic (diagenetic) bottom-near seawater and/or pore water (Wegorzewski and Kuhn, 2014, Mar. Geol. 357, 123-138). Preliminary results show that there are significant differences between the geochemical composition of nodules grown at sediment surface and those found within sediments. Compared to surface nodules, buried nodules are enriched in Co and W, but have lower concentration of Mo, Ba, Zn and Li. The distribution of Rare Earth Elements and Y(REY) is also different. Furthermore, the locations of the buried manganese nodules correlates with increased contents of Mn, Co and other elements in the suboxic pore water. It seems that the hydrogenetic layers of the buried nodules were dissolved and/ or recrystallized due to diagenetic processes in the sediment. As a result, a new Fe-rich layer type was formed, with Mn being released into the pore water and/or being used to form todorokite in the nodules. The mineralogical analyses of surface and buried nodules support this assumption. Until now, it couldńt be proven that the hydrothermal fluid flow in the basalts underneath the sediments has an influence on the nodule geochemistry.

Microbial life in continental salt pan sediments and their response to climate variability in Northern South Africa

NASA Astrophysics Data System (ADS)

Genderjahn, Steffi; Mangelsdorf, Kai; Alawi, Mashal; Belz, Lukas; Kallmeyer, Jens; Wagner, Dirk

2016-04-01

The environmental history of southwestern African mainland is largely unknown. Since there are no lacustrine systems with constant water coverage in this area, we investigated a continental salt pan as a terrestrial geoarchive with the potential to preserve climate signals. Within the frame of the research project "GeoArchives" (part of the SPACES program, funded by the German Federal Ministry of Education and Research, BMBF) we aimed to reconstruct climate variabilities during the late Pleistocene to Holocene. The presented study is focused on variations within the microbial community structure and abundance of key organisms in a salt pan with special regards to sediment age and geochemical parameters. A combined approach of a 16S rDNA-based quantification method and lipid biomarker analysis was used to demonstrate the response of the microbial communities with respect to environmental changes. The phospholipid derived fatty acids (PLFAs) in sedimentary deposits are characteristic markers for living Bacteria, whereby their side chain represents a fingerprint of the community structure on a broad taxonomic level. Archaeol and isoprenoid glycerol dialkyl glycerol tetraethers (iGDGTs) were used as characteristic makers for Archaea whereas branched GDGTs (brGDGTs) are typical biomarkers for Bacteria. In contrast to PLFAs, they represent dead microbial biomass and thus the past microbial communities in older sediments, since they are already partly degraded. Samples from the Witpan, located in the northwest of South Africa and representing a depths profile from the Late Pleistocene to Holocene, were gathered. Despite the extreme environment with rather low TOC values, restricted availability of water and high salt concentration markers for Bacteria and Archaea were observed. A series of saturated, branched and unsaturated PLFAs were identified. The diversity and concentration of PLFAs were highest in the top layers (up to 30000 ng gsed-1, 0-10 cm) and characteristic markers for cyanobacteria were most abundant. The community composition changed with depths and both the copy numbers of 16S rDNA genes of bacteria (varied from 102 to 105 cell gsed-1) and the amount of PLFAs (up to 3000 ng gsed-1) reflected a low abundance of microorganisms despite increasing feedstock in deeper sediments. Thus, the actual salt pan microbial community is mainly located in the top layers and decreases with depth. In contrast archaeol and GDGTs increased at the transition from Holocene to deeper Late Pleistocene sediments (from 40 up to 3400 ng gsed-1) indicating a higher past microbial abundance during the Late Pleistocene. The increase of GDGTs, TOC, acetate and formate suggested a higher supply of organic matter and a higher microbial activity in this period. Therefore, we assumed an increased precipitation during the Late Pleistocene compared to the arid Holocene in southwestern Africa. We could show the potential of continental salt pans to preserve climate signals during deposition and we demonstrated their potential as a Late Quaternary geoarchive by means of lipid biomarker studies. To describe the environmental habitat, a detailed analysis of diversity and abundance of microorganisms using Next Generation Sequencing is planned.

Assessing and modeling sediment mobility in estuarine and coastal settings due to extreme climate events from natural short-lived isotope distribution

NASA Astrophysics Data System (ADS)

Ghaleb, Bassam; Hillaire-Marcel, Claude; Ruiz Fernandez, Ana-Carolina; Sanchez Cabeza, Joan-Albert

2016-04-01

Climatic events (e.g. floods, storminess) and management activities (e.g. dredging) may result in the burial or removal and re-suspension of sediments in estuaries and coastal areas. When such sediments are contaminated, such processes may either help restoring better chemical environments or lead to their long-term contamination. Geochemical signatures in surface sediments may help identifying such sedimentological events. However, short-lived isotope data are generally required to set time-constraints on their occurrence. Whereas 210Pb and radioactive fallout isotope contents can help setting time constraints at ~50 to ~100 yr-time scales, natural disequilibria in the 232Th-228Ra-228Th sequence do provide information on processes which occurred within the last 30 yrs, as illustrated in the present study. Box-cored sediments from the Saguenay Fjord and lower estuary of the St. Lawrence (Canada) as well as from estuaries and lagoons from the Sinaloa Coast (Mexico) are used to document the behavior of these isotopes either under relatively steady conditions (St. Lawrence estuary) or under high-frequency extreme climate events (storms and floods; Saguenay Fjord, Coastal Sinaloa). 228Th/232Th activity ratios were determined by chemical extraction of Th and alpha counting of unspiked samples, rapidly after sampling (228Th/232Th). The activity of the intermediate isotope 228Ra was then estimated based on replicate measurements on aliquot samples made a few years later. Under steady conditions, core-top sediment shows an excess in 228Th vs 232Th (AR ~ 1.6), whereas the intermediate 228Ra depicts a deficit vs its parent 232Th (AR ~0.6). Downcore, radioactive decay carries rapidly 228Th-activities to those of the parent 228Ra within about 10 yrs (i.e., ~ 5 half-lives of 228Th), then both move during the next ~20 yrs (~ i.e., ~ 5 half-lives of 228Ra, when added to the 10 yrs of 228Th-excess) towards secular equilibrium with the parent long-lived 232Th. A few algorithms provide simple models governing these processes under relatively high sedimentation rates, i.e., when Ra-diffusion from the sediment towards the water column may be neglected. In sites characterized by extreme sedimentologival events, 228Th/232Th profiles depict departures from this model, thus bearing information on the timing and processes involved. Examples from the Saguenay Fjord (Canada) illustrate the case of fast-deposited layers due to floods, whereas examples from estuaries and coastal areas of Sinaloa show evidence for re-suspension and/or erosion events linked notably to storminess and/or land use changes. In the first case, the fast accumulation of flood layers has sealed most of the early 20th-century contamination, whereas in the second case, erosion and re-suspension events led to either some removal of sediments contaminated by heavy metals, or their secondary release into the environment.

Stabilizing Effects of Bacterial Biofilms: EPS Penetration and Redistribution of Bed Stability Down the Sediment Profile

NASA Astrophysics Data System (ADS)

Chen, X. D.; Zhang, C. K.; Zhou, Z.; Gong, Z.; Zhou, J. J.; Tao, J. F.; Paterson, D. M.; Feng, Q.

2017-12-01

Biofilms, consisting of microorganisms and their secreted extracellular polymeric substances (EPSs), serve as "ecosystem engineers" stabilizing sedimentary environments. Natural sediment bed provides an excellent substratum for biofilm growth. The porous structure and rich nutrients allow the EPS matrix to spread deeper into the bed. A series of laboratory-controlled experiments were conducted to investigate sediment colonization of Bacillus subtilis and the penetration of EPS into the sediment bed with incubation time. In addition to EPS accumulation on the bed surface, EPS also penetrated downward. However, EPS distribution developed strong vertical heterogeneity with a much higher content in the surface layer than in the bottom layer. Scanning electron microscope images of vertical layers also displayed different micromorphological properties of sediment-EPS matrix. In addition, colloidal and bound EPSs exhibited distinctive distribution patterns. After the full incubation, the biosedimentary beds were eroded to test the variation of bed stability induced by biological effects. This research provides an important reference for the prediction of sediment transport and hence deepens the understanding of the biologically mediated sediment system and broadens the scope of the burgeoning research field of "biomorphodynamics."

Advanced Water Quality Modelling in Marine Systems: Application to the Wadden Sea, the Netherlands

NASA Astrophysics Data System (ADS)

Boon, J.; Smits, J. G.

2006-12-01

There is an increasing demand for knowledge and models that arise from water management in relation to water quality, sediment quality (ecology) and sediment accumulation (ecomorphology). Recently, models for sediment diagenesis and erosion developed or incorporated by Delft Hydraulics integrates the relevant physical, (bio)chemical and biological processes for the sediment-water exchange of substances. The aim of the diagenesis models is the prediction of both sediment quality and the return fluxes of substances such as nutrients and micropollutants to the overlying water. The resulting so-called DELWAQ-G model is a new, generic version of the water and sediment quality model of the DELFT3D framework. One set of generic water quality process formulations is used to calculate process rates in both water and sediment compartments. DELWAQ-G involves the explicit simulation of sediment layers in the water quality model with state-of-the-art process kinetics. The local conditions in a water layer or sediment layer such as the dissolved oxygen concentration determine if and how individual processes come to expression. New processes were added for sulphate, sulphide, methane and the distribution of the electron-acceptor demand over dissolved oxygen, nitrate, sulphate and carbon dioxide. DELWAQ-G also includes the dispersive and advective transport processes in the sediment and across the sediment-water interface. DELWAQ-G has been applied for the Wadden Sea. A very dynamic tidal and ecologically active estuary with a complex hydrodynamic behaviour located at the north of the Netherlands. The predicted profiles in the sediment reflect the typical interactions of diagenesis processes.

Taking into Account Interelement Interference in X-Ray Fluorescence Analysis of Thin Two-Layer Ti/V Systems

NASA Astrophysics Data System (ADS)

Mashin, N. I.; Razuvaev, A. G.; Cherniaeva, E. A.; Gafarova, L. M.; Ershov, A. V.

2018-03-01

We propose a new method for determining the thickness of layers in x-ray fluorescence analysis of two-layer Ti/V systems, using easily fabricated standardized film layers obtained by sputter deposition of titanium on a polymer film substrate. We have calculated correction factors taking into account the level of attenuation for the intensity of the primary emission from the x-ray tube and the analytical line for the element of the bottom layer in the top layer, and the enhancement of the fluorescence intensity for the top layer by the emission of atoms in the bottom layer.

STM/STS study of superconducting properties in Ca10(Pt4As8)(Fe2As2)5

NASA Astrophysics Data System (ADS)

Kim, Jisun; Nam, Hyoungdo; Li, Guorong; Karki, Amar; Shih, Chih-Kang; Zhang, Jiandi; Jin, Rongying; Plummer, E. W.

2014-03-01

Newly discovered iron-based superconductor, Ca10(Pt4As8)(Fe2As2)5 (Tc = 34 K) is studied using scanning tunneling microscopy/spectroscopy (STM/S). Given the symmetry of the crystal structure, several surface terminations are expected with roughly same probability: 1) Ca or partial Ca layer on top Fe2As2; 2) Ca or partial Ca layer on top Pt4As8 layer; 3) A Fe2As2 layer, and; 4) A Pt4As8layer.Surprisingly,Fe2As2 related layers (1 & 3) are rarely observed (less than 1%). Instead, we observe Pt4As8 layers separated by unit-cell-high (~ 1 nm) steps accompanied with Ca or partial Ca layer on top Pt4As8 layer (1 - 2 Å step height). Scanning tunneling spectroscopy reveals different spectra for each surface, with superconducting coherence peaks seen only on Ca layers. We argue that intermediary layers are proximity-coupled to superconducting Fe2As2 layers. The results from Ca10(Pt4As8)(Fe2As2)5 are discussed with the properties observed in other iron-based superconductors. Funded by NSF

Top-Down Visual Saliency via Joint CRF and Dictionary Learning.

PubMed

Yang, Jimei; Yang, Ming-Hsuan

2017-03-01

Top-down visual saliency is an important module of visual attention. In this work, we propose a novel top-down saliency model that jointly learns a Conditional Random Field (CRF) and a visual dictionary. The proposed model incorporates a layered structure from top to bottom: CRF, sparse coding and image patches. With sparse coding as an intermediate layer, CRF is learned in a feature-adaptive manner; meanwhile with CRF as the output layer, the dictionary is learned under structured supervision. For efficient and effective joint learning, we develop a max-margin approach via a stochastic gradient descent algorithm. Experimental results on the Graz-02 and PASCAL VOC datasets show that our model performs favorably against state-of-the-art top-down saliency methods for target object localization. In addition, the dictionary update significantly improves the performance of our model. We demonstrate the merits of the proposed top-down saliency model by applying it to prioritizing object proposals for detection and predicting human fixations.

Physical subdivision and description of the water-bearing sediments of the Santa Clara Valley, California

USGS Publications Warehouse

Wentworth, Carl M.; Jachens, Robert C.; Williams, Robert A.; Tinsley, John C.; Hanson, Randall T.

2015-01-01

Maps and cross sections show the elevations of cycle boundaries and the underlying bedrock surface, the varying thicknesses of the cycles and of their fine tops and coarse bottoms, and the aggregate thickness of coarse layers in those bottom intervals. Coarse sediment is more abundant toward some parts of the basin margin and in the southern part of the basin. Cycle boundary surfaces are relatively smooth, and their shapes are consistent with having been intercycle topographic surfaces. The underlying bedrock surface has a relief of more than 1,200 feet and deepens toward the center of the basin and the west edge of the fault-bounded Evergreen Basin, which is concealed beneath the east side of the Quaternary basin. The absence of consistent abrupt changes in thicknesses or boundary elevations across the basin or in cross section indicates that the interior of the basin is largely unfaulted, with the Silver Creek strand of the San Andreas system at the west edge of the Evergreen Basin being the sole exception. The east and west margins of the Santa Clara Basin, in contrast, are marked by reverse and thrust fault systems.

­­­­Submarine Mass Wasting on Hovgaard Ridge, Fram Strait, European Arctic

NASA Astrophysics Data System (ADS)

Forwick, M.; Laberg, J. S.; Husum, K.; Gales, J. A.

2015-12-01

Hovgaard Ridge is an 1800 m high bathymetric high in the Fram Strait, the only deep-water gateway between the Arctic Ocean and the other World's oceans. The slopes of the ridge provide evidence of various types of sediment reworking, including 1) up to 12 km wide single and merged slide scars with maximum ~30 m high headwalls and some secondary escarpments; 2) maximum 3 km wide and 130 m deep slide scars with irregular internal morphology, partly narrowing towards the foot of the slope; 3) up to 130 m deep, 1.5 km wide and maximum 8 km long channels/gullies originating from areas of increasing slope angle at the margins of a plateau on top of the ridge. Most slide scars result presumably from retrogressive failure related to weak layers in contourites or ash. The most likely trigger mechanism is seismicity related to tectonic activity within the nearby mid-ocean fracture zone. Gully/channel formation is suggested to result from cascading water masses and/or from sediment gravity flows originating from failure at the slope break after winnowing on the plateau of the ridge.

The effect of annealing on the MR and exchange bias characteristics in dual spin valve with nano-oxide layer

NASA Astrophysics Data System (ADS)

Jang, S. H.; Kang, T.; Kim, H. J.; Kim, K. Y.

2002-02-01

We investigated magnetoresistance (MR) and exchange bias properties by annealing in the dual spin valve (SV) with nano-oxide layer (NOL). By analyzing effects of NOL in top and bottom pinned simple SVs, MR enhancement effect of NOL inserted in the bottom pinned layer was higher than that of NOL in the top pinned layer with annealing. By the enhanced specular scattering of electrons by NOL, the MR ratio of dual SV with NOL was increased to 15.5-15.9% with an annealing of 200-250°C. Exchange coupling constant Jex was improved rapidly as 0.13-0.16 erg/cm 2 by annealing in the bottom pinned layer, whereas the effect of annealing was not large in the top pinned layer with Jex of about 0.09-0.116 erg/cm 2.

Linear segmentation algorithm for detecting layer boundary with lidar.

PubMed

Mao, Feiyue; Gong, Wei; Logan, Timothy

2013-11-04

The automatic detection of aerosol- and cloud-layer boundary (base and top) is important in atmospheric lidar data processing, because the boundary information is not only useful for environment and climate studies, but can also be used as input for further data processing. Previous methods have demonstrated limitations in defining the base and top, window-size setting, and have neglected the in-layer attenuation. To overcome these limitations, we present a new layer detection scheme for up-looking lidars based on linear segmentation with a reasonable threshold setting, boundary selecting, and false positive removing strategies. Preliminary results from both real and simulated data show that this algorithm cannot only detect the layer-base as accurate as the simple multi-scale method, but can also detect the layer-top more accurately than that of the simple multi-scale method. Our algorithm can be directly applied to uncalibrated data without requiring any additional measurements or window size selections.

Determination of boundary layer top on the basis of the characteristics of atmospheric particles

NASA Astrophysics Data System (ADS)

Liu, Boming; Ma, Yingying; Gong, Wei; Zhang, Ming; Yang, Jian

2018-04-01

The planetary boundary layer (PBL) is the lowest layer of the atmosphere that can be directly influenced with the Earth's surface. This layer can also respond to surface forcing. The determination of the PBL is significant to environmental and climate research. PBL can also serve as an input parameter for further data processing with atmospheric models. Traditional detection algorithms are susceptible to errors associated with the vertical distribution of aerosol concentrations. To overcome this limitation, a maximum difference search (MDS) algorithm was proposed to calculate the top of the boundary layer based on differences in particle characteristics. The top positions of the PBL from MDS algorithm under different convection states were compared with those from conventional methods. Experimental results demonstrated that the MDS method can determine the top of the boundary layer precisely. The proposed algorithm can also be used to calculate the top of the PBL accurately under weak convection conditions where the traditional methods cannot be applied. Finally, experimental data from June 2015 to December 2015 were analysed to verify the reliability of the MDS algorithm. The correlation coefficients R2 (RMSE) between the results of MDS algorithm and radiosonde measurements were 0.53 (115 m), 0.79 (141 m) and 0.96 (43 m) under weak, moderate and strong convections, respectively. These findings indicated that the proposed method possessed a good feasibility and stability.

Effect of topographic characteristics on compound topographic index for identification of gully channel initiation locations

USDA-ARS?s Scientific Manuscript database

Sediment loads from gully erosion can be a significant sediment source within watershed resulting in major contributions to water quality problems, reduction of crop productivity by removal of nutrient rich top soil, and damaging downstream ecosystems. Areas containing a high probability of forming ...

ASSESSING WATER QUALITY CHANGES IN THE LAKES OF THE NORTHEASTERN UNITED STATES USING SEDIMENT DIATOMS

EPA Science Inventory

Diatom assemblages were selected as indicators of lake condition and to assess historical lake water quality changes in 257 lakes in the northeastern United States. The "top" (surface sediments, present-day) and "bottom" (generally from >30 cm deep, representing historical condit...

Sediment Accretion During Horst and Graben Subduction associated with the Tohoku Oki M9 Earthquake, Northern Japan

NASA Astrophysics Data System (ADS)

Moore, J. C.; Chester, F. M.

2015-12-01

The stratigraphic sequence within the frontal accretionary prism of the Japan Trench, the site of large slip during the Tohoku earthquake, is unique due to horst and graben subduction. Boreholes at IODP Site C0019, penetrating the toe of the Tohoku accretionary prism, document a younger over older intraprism thrust contact with a 9 Ma age gap across the basal plate boundary fault. The anomalously young (Quaternary to Pliocene), fault-bounded sediment package is 130 m thick, of a total of 820 m of sediment above the plate boundary fault. In contrast, typical accretionary prism structure consists of stacked sediment packages on imbricate faults above the basal decollement resulting in an overall increase in age downward. Site C0019 penetrates the prism directly above a horst of the subducting Pacific oceanic crust. Here the plate-boundary fault consists of a thin, weak smectitic pelagic clay that is probably the principal slip surface of ~50 m offset in the 2011 Tohoku earthquake. The fault continues seaward deepening off the seaward edge of the horst and beneath the sediment fill of the adjacent graben, dying out at the landward base of the next incoming horst. The plate boundary fault and its splays in the graben form a narrow-taper protoprism and a small sedimentary basin of trench fill marking the seaward edge of the upper plate. The modern fault and sediment distributions within the graben are used to motivate a viable model for the presence of anomalously young sediments directly above the plate boundary fault. In this model sediments in the trench are thrust over the incoming horst by propagation of the plate boundary thrust up the landward-dipping fault of the incoming horst and along the smectitic clay layer to emplace Quaternary and Pliocene trench deposits directly on top of the incoming horst. These young deposits are in turn overlain by sediments 9 Ma or older that have been transported out of the graben along imbricate faults associated with the necessary increase in the taper of the prism above the graben. The Quaternary to Pliocene units thicken due to internal deformation accounting for the 130 m thickness now observed over the plate boundary fault at Site C0019. Conversely emplacement of very young sediment directly above a basal detachment would be unexpected in accretionary prisms subducting smoother oceanic crust.

Tuning the magnetism of the top-layer FeAs on BaFe2As2 (001): First-principles study

NASA Astrophysics Data System (ADS)

Zhang, Bing-Jing; Liu, Kai; Lu, Zhong-Yi

2018-04-01

Magnetism may play an important role in inducing the superconductivity in iron-based superconductors. As a prototypical system, the surface of BaFe2As2 provides a good platform for studying related magnetic properties. We have designed systematic first-principles calculations to clarify the surface magnetism of BaFe2As2 (001), which previously has received little attention in comparison with surface structures and electronic states. We find that the surface environment has an important influence on the magnetic properties of the top-layer FeAs. For As-terminated surfaces, the magnetic ground state of the top-layer FeAs is in the staggered dimer antiferromagnetic (AFM) order, distinct from that of the bulk, while for Ba-terminated surfaces the collinear (single-stripe) AFM order is the most stable, the same as that in the bulk. When a certain coverage of Ba or K atoms is deposited onto the As-terminated surface, the calculated energy differences among different AFM orders for the top-layer FeAs on BaFe2As2 (001) can be much reduced, indicating enhanced spin fluctuations. To compare our results with available scanning tunneling microscopy (STM) measurements, we have simulated the STM images of several structural/magnetic terminations. Astonishingly, when the top-layer FeAs is in the staggered dimer AFM order, a stripe pattern appears in the simulated STM image even when the surface Ba atoms adopt a √{2 }×√{2 } structure, while a √{2 }×√{2 } square pattern comes out for the 1 ×1 full As termination. Our results suggest: (i) the magnetic state at the BaFe2As2 (001) surface can be quite different from that in the bulk; (ii) the magnetic properties of the top-layer FeAs can be tuned effectively by surface doping, which may likely induce superconductivity at the surface layer; (iii) both the surface termination and the AFM order in the top-layer FeAs can affect the STM image of BaFe2As2 (001), which needs to be taken into account when identifying the surface termination.

Cryofacies evidences of a Yedoma (?) development during the last glacial maximum in Yukon (Canada) along the current Alaska border

NASA Astrophysics Data System (ADS)

Stephani, E.; Fortier, D.; Shur, Y.

2012-12-01

In some areas that remained unglaciated during the Late Pleistocene, inorganic and organic sedimentation supported syngenetic upward permafrost development and the creation of so-called yedoma deposits (Ice Complex). This type of periglacial deposit is usually very ice-rich and is highly unstable upon thawing. As this deposit thaws, the landscape goes from a carbon sink to a carbon and inorganic sediment source. This carbon can be released into the environment or transformed to CH4. Yedoma deposits have been extensively studied in Russia and more recently in Alaska. However, very few studies have focused on yedomas of Yukon. With the objective to provide regional information on yedoma distribution in North America, we present here preliminary field evidences of a yedoma deposit near Beaver Creek, close to current Alaska border. 28 boreholes were core-drilled, and cores were described and analyzed in the laboratory. Well-developed microlenticular cryostructures in silt and numerous small rootlets are typical of yedoma deposit. Tiny ice lenses are formed in fine-grained sediment by cryosuction and rootlets gets incorporated into the permafrost as the table rises syngenetically in response to surface sedimentation. During sedimentary accumulation, when sedimentation slows down, peat layers can be formed at the surface. This change in material properties often lead to the development of belt-like cryostructures (thick ice lenses separated by reticulate ice veins). At Beaver Creek, the microlenticular and belt-like cryofacies with rootlets (typical of syngenetic ice-rich yedoma) were abundant in Units 2A and 2C. The average ice content of Units 2A and 2C was respectively 91 % and 109 %, and the organic matter content (loss on ignition) was 6 % and 8 %. Significant thaw strain was measured in Units 2A (50%) and 2C (35%). Interestingly Unit 2B was very ice-poor (gravimetric ice content: 47 %, thaw strain: 9 %) and showed only porous cryostructure (interstitial ice) in silt (3 % organic matter). This was interpreted as ice-rich fine-grained soils that thawed, drained, and refroze afterward. This ice-poor layer with sediment deformations (e.g. fold, fault, diapir) is called 'taberal deposit' in the Russian literature. This layer can be observed in yedoma deposit in areas which were affected by permafrost degradation. Yedoma deposits are usually characterized by the presence of tall and wide ice wedges. These wedges form continuously as the permafrost table rises in response to surface sedimentation and their size is thus a function of sedimentation rate and time. In our study, we observed ice wedges at least 8 m tall (tip of the wedge > maximum coring depth). The bottom of the ice wedges was located in lodgement till (> 11 m below surface). This deposit was covered by woody peat deposit up to 4.9 m thick and was thus interpreted to be older than MIS 3. We propose that frost cracking first occurred in the peat and the underlying diamicton after the last interglacial and that upward syngenetic ice wedge growth followed silt accumulation over thousands of years sometimes during the last glacial period. The top of the ice wedges were located at about 2.5 m depth in Unit 2B. This indicates that ice wedge growth was interrupted by an episode of permafrost degradation and resumed afterward during accumulation of unit 2A.

Seismically-triggered soft-sediment deformation structures close to a major strike-slip fault system in the Eastern Alps (Hirlatz cave, Austria)

NASA Astrophysics Data System (ADS)

Salomon, Martina Lan; Grasemann, Bernhard; Plan, Lukas; Gier, Susanne; Schöpfer, Martin P. J.

2018-05-01

We investigate episodic soft-sediment deformation structures cross-cut by normal faults preserved in unlithified finely laminated calcite rich sediments in the Hirlatz cave in the Northern Calcareous Alps (Austria). These sediments comprise varve-like alternations of brighter carbonate/quartz rich layers, and darker clay mineral rich layers. The deformed sediments contain abundant millimeter to centimeter-scale soft-sediment structures (load casts, ball-and-pillow structures), sheet slumps (thrust faults and folds), erosive channels filled with slides and chaotic slumps. After deposition and soft-sediment deformation normal faults developed within the entire sedimentary succession, an event that probably correlates with an offset of c. 10 cm of the passage wall above the outcrop. Our major conclusions are: (i) The sediments have a glacial origin and were deposited in the Hirlatz cave under phreatic fluvio-lacustrine conditions. The deposition and the soft-sediment deformation occurred most likely during the last glaciation (i.e. around 25 ka ago); (ii) The liquefaction and formation of the soft-sediment structures in water-saturated stratified layers was triggered by episodic seismic events; (iii) The internally deformed sediments were later displaced by normal faults; (iv) A possible source for the seismic events is the active sinistral Salzach-Ennstal-Mariazeller-Puchberger (SEMP) strike-slip fault which is located about 10 km south of the outcrop and plays a major role in accommodating the extrusion of the Eastern Alps towards the Pannonian Basin. To our knowledge, the described structures are the first report of liquefaction and seismically induced soft-sediment deformations in Quaternary sediments in the Eastern Alps.

Two-layer anti-reflection strategies for implant applications

NASA Astrophysics Data System (ADS)

Guerrero, Douglas J.; Smith, Tamara; Kato, Masakazu; Kimura, Shigeo; Enomoto, Tomoyuki

2006-03-01

A two-layer bottom anti-reflective coating (BARC) concept in which a layer that develops slowly is coated on top of a bottom layer that develops more rapidly was demonstrated. Development rate control was achieved by selection of crosslinker amount and BARC curing conditions. A single-layer BARC was compared with the two-layer BARC concept. The single-layer BARC does not clear out of 200-nm deep vias. When the slower developing single-layer BARC was coated on top of the faster developing layer, the vias were cleared. Lithographic evaluation of the two-layer BARC concept shows the same resolution advantages as the single-layer system. Planarization properties of a two-layer BARC system are better than for a single-layer system, when comparing the same total nominal thicknesses.

Provenance and depositional conditions of Cretaceous-Paleogene boundary sandstones from northeastern Mexico

NASA Astrophysics Data System (ADS)

Rehrmann, Stephanie; Augustsson, Carita; Izaguirre Valdez, Rocio Nereyda; Jenchen, Uwe; Schulte, Peter

2012-12-01

We compare Late Maastrichtian siliciclastic sandstone in northeastern Mexico with those representing the Cretaceous-Paleogene (K-Pg) boundary to reveal differences in provenance and depositional conditions between background sedimentation and K-Pg sand. Lithology and compositional variations are presented for the deep-water Burgos Basin and the shallow-water La Popa Basin. The Late Maastrichtian sandstones in the Burgos Basin have sharp lower contacts, contain abundant trace fossils and are separated by meter-thick marl layers. They represent sporadic mass flows from coastal areas separated by long phases of hemipelagic sedimentation. The K-Pg sandstone layers are amalgamated, contain thin marl intercalations only in the uppermost part and trace fossils are present in the top sandstone layer only. Also this succession represents mass-flow deposits, but the sand may have been deposited during a very short period. The La Popa Basin sandstones represent deltaic sedimentation interrupted by submarine channel deposition during the K-Pg boundary transition with abundant rip-up clasts and bioclasts at the base. The sandstones of the Burgos Basin are quartz to akosic wacke dominated by quartz (> 90%) and some feldspar (< 10%) in calcite cement and matrix. Lithic fragments are rare and dominated by chert and bioclasts. Ultra-stable heavy minerals (ZTR = 50-80) and plutonic quartz grains (ca. 40% of the total quartz population) are particularly common in the K-Pg sandstones. In the Maastrichtian sandstones, metamorphic heavy minerals, particularly chlorite, clinozoisite, and tourmaline (20-50% of the heavy mineral population), and metamorphic quartz (80% of the quartz population) have higher abundances. The La Popa sandstones are subarkose to arkose and arkosic wacke and have a high abundance of feldspar (15-30%) and lithic fragments (5-20%), mainly of siltstone and carbonate. The sandstones from both basins have chemical compositions typical for recycling (Zr/Sc = 12-27 and 17-140 in the Burgos and La Popa Basin, respectively) and influences from mafic source rocks (Th/Sc = 0.4-1.1; Ti/Nb = 350-510). Therefore we suggest that all studied successions share a common provenance with transport of recycled orogenic metasedimentary components from northwestern Mexico and magmatic arc material from western Mexico. Subsequently, longshore currents mixed the detritus with limestone clasts derived from the tectonically active Sierra Madre Oriental, which probably is the cause for compositional changes in the sandstones. Due to increased sediment input from western Mexico at the K-Pg boundary, provenance changes cannot be related to the Chicxulub impact.

Layer-by-layer modification of thin-film metal-semiconductor multilayers with ultrashort laser pulses

NASA Astrophysics Data System (ADS)

Romashevskiy, S. A.; Tsygankov, P. A.; Ashitkov, S. I.; Agranat, M. B.

2018-05-01

The surface modifications in a multilayer thin-film structure (50-nm alternating layers of Si and Al) induced by a single Gaussian-shaped femtosecond laser pulse (350 fs, 1028 nm) in the air are investigated by means of atomic-force microscopy (AFM), scanning electron microscopy (SEM), and optical microscopy (OM). Depending on the laser fluence, various modifications of nanometer-scale metal and semiconductor layers, including localized formation of silicon/aluminum nanofoams and layer-by-layer removal, are found. While the nanofoams with cell sizes in the range of tens to hundreds of nanometers are produced only in the two top layers, layer-by-layer removal is observed for the four top layers under single pulse irradiation. The 50-nm films of the multilayer structure are found to be separated at their interfaces, resulting in a selective removal of several top layers (up to 4) in the form of step-like (concentric) craters. The observed phenomenon is associated with a thermo-mechanical ablation mechanism that results in splitting off at film-film interface, where the adhesion force is less than the bulk strength of the used materials, revealing linear dependence of threshold fluences on the film thickness.

Sedimentary record of sub-glacial outburst floods at Laurentian Fan

NASA Astrophysics Data System (ADS)

Leng, Wei; von Dobeneck, Tilo

2016-04-01

Large-scale glacial meltwater discharge could be widely recognized off the eastern Canadian continental margin. At Laurentian Fan, sub-glacial outburst floods eroded Permian-Carboniferous redbeds at Gulf of St. Lawrence and then delivered the reddish sediments by Laurentian Channel. Sedimentary record from four gravity cores (GeoB18514-2, 18515-1, 18516-2 and 18517-1) at the SW slope of the Grand Banks of Newfoundland revealed the major depositional processes since Heinrich event 2 (ca. 22 ka). In the cores, the upper thick Holocene olive-grey silty mud units overly IRD-rich Heinrich 1 layer, five reddish units are distinguished in the lower part. Reddish units get proportionally thinner along the SW slope at higher and more distal positions; instead, separating olive-grey layers get thicker with height and distance. Reddish and olive grey units have sharp boundaries and no signs of erosion. Mean grain size changes abruptly from coarse in grey layers to fine in reddish layers, terrigenous elements (as Al, K, Ti, Fe) and clays (Al/Si) are highly elevated in reddish layers and low in Heinrich layers, which are instead enriched in detrital continental carbonates. Both Heinrich layers and reddish layers have enhanced magnetic susceptibility, but Heinrich layer have higher ferromagnetic (SIRM) content (mafic rocks), while reddish layers have more hematite (HIRM). These five reddish layers differ from event to event, which seems to reflect different mixing ratios of event-related and background sedimentation. This mixing will allow estimating event-specific sedimentation rates. Using mixing ratio combined with 14C dating data could contribute to estimate the sedimentation rate and duration of outburst floods, which could help to build ice sheet retreat history and find the connection with paleoclimate changes.

A model for the estimation of the surface fluxes of momentum, heat and moisture of the cloud topped marine atmospheric boundary layer from satellite measurable parameters. M.S. Thesis

NASA Technical Reports Server (NTRS)

Allison, D. E.

1984-01-01

A model is developed for the estimation of the surface fluxes of momentum, heat, and moisture of the cloud topped marine atmospheric boundary layer by use of satellite remotely sensed parameters. The parameters chosen for the problem are the integrated liquid water content, q sub li, the integrated water vapor content, q sub vi, the cloud top temperature, and either a measure of the 10 meter neutral wind speed or the friction velocity at the surface. Under the assumption of a horizontally homogeneous, well-mixed boundary layer, the model calculates the equivalent potential temperature and total water profiles of the boundary layer along with the boundary layer height from inputs of q sub li, q sub vi, and cloud top temperature. These values, along with the 10m neutral wind speed or friction velocity and the sea surface temperature are then used to estimate the surface fluxes. The development of a scheme to parameterize the integrated water vapor outside of the boundary layer for the cases of cold air outbreak and California coastal stratus is presented.

Stable carbon and oxygen isotope record of central Lake Erie sediments

USGS Publications Warehouse

Tevesz, M.J.S.; Spongberg, A.L.; Fuller, J.A.

1998-01-01

Stable carbon and oxygen isotope data from mollusc aragonite extracted from sediment cores provide new information on the origin and history of sedimentation in the southwestern area of the central basin of Lake Erie. Sediments infilling the Sandusky subbasin consist of three lithologic units overlying glacial deposits. The lowest of these is a soft gray mud overlain by a shell hash layer containing Sphaerium striatinum fragments. A fluid mud unit caps the shell hash layer and extends upwards to the sediment-water interface. New stable isotope data suggest that the soft gray mud unit is of postglacial, rather than proglacial, origin. These data also suggest that the shell hash layer was derived from erosional winnowing of the underlying soft gray mud layer. This winnowing event may have occurred as a result of the Nipissing flood. The Pelee-Lorain moraine, which forms the eastern boundary of the Sandusky subbasin, is an elevated area of till capped by a sand deposit that originated as a beach. The presence of both the shell hash layer and relict beach deposit strengthens the interpretation that the Nipissing flood was a critical event in the development of the southwestern area of the central basin of Lake Erie. This event, which returned drainage from the upper lakes to the Lake Erie basin, was a dominant influence on regional stratigraphy, bathymetry, and depositional setting.

Sensing Shallow Seafloor and Sediment Properties, Recent History

DTIC Science & Technology

2008-09-01

instances, larger samplers, i.e. box corers, can be further subsampled with small push-in tubes , yielding relatively undisturbed specimens. Corers...sediment within the sampling tube 3 during retrieval. Generally, common gravity corers can retrieve up to 5m (in softer sediments) of soil, whereas... tube that can be generated. Vibro-corers are similar to the gravity corers but have a motorized unit added to the top of the assembly, generating an

Sedimentation from flocculated suspensions in the presence of settling-driven gravitational interface instabilities

NASA Astrophysics Data System (ADS)

Rouhnia, Mohamad; Strom, Kyle

2015-09-01

We experimentally examine sedimentation from a freshwater suspension of clay flocs overlying saltwater in the presence of gravitational instabilities. The study seeks to determine: (1) if flocculation hampers or alters interface instability formation; (2) how the removal rates of sediment from the buoyant layer compare to those predicted by individual floc settling; and (3) whether or not it is possible to develop a model for effective settling velocity. The experiments were conducted in a tank at isothermal conditions. All experiments were initially stably stratified but later developed instabilities near the interface that grew into downward convecting plumes of fluid and sediment. Throughout, we measured sediment concentration in the upper and lower layers, floc size, and plume descent rates. The data showed that flocculation modifies the mixture settling velocity, and therefore shifts the mode of interface instability from double-diffusive (what one would expect from unflocculated clay) to settling-driven leaking and Rayleigh-Taylor instability formation. Removal rates of sediment from the upper layer in the presence of these instabilities were on the same order of magnitude as those predicted by individual floc settling. However, removal rates were found to better correlate with the speed of the interface plumes. A simple force-balance model was found to be capable of reasonably describing plume velocity based on concentration in the buoyant layer. This relation, coupled with a critical Grashof number and geometry relations, allowed us to develop a model for the effective settling velocity of the mixture based solely on integral values of the upper layer.

Optimized capping layers for EUV multilayers

DOEpatents

Bajt, Sasa [Livermore, CA; Folta, James A [Livermore, CA; Spiller, Eberhard A [Livermore, CA

2004-08-24

A new capping multilayer structure for EUV-reflective Mo/Si multilayers consists of two layers: A top layer that protects the multilayer structure from the environment and a bottom layer that acts as a diffusion barrier between the top layer and the structure beneath. One embodiment combines a first layer of Ru with a second layer of B.sub.4 C. Another embodiment combines a first layer of Ru with a second layer of Mo. These embodiments have the additional advantage that the reflectivity is also enhanced. Ru has the best oxidation resistance of all materials investigated so far. B.sub.4 C is an excellent barrier against silicide formation while the silicide layer formed at the Si boundary is well controlled.

Release of Methane from Bering Sea Sediments During the Last Glacial Period

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mea Cook; Lloyd Keigwin

2007-11-30

Several lines of evidence suggest that during times of elevated methane flux the sulfate-methane transition zone (SMTZ) was positioned near the sediment-water interface. We studied two cores (from 700 m and 1457 m water depth) from the Umnak Plateau region. Anomalously low d13C and high d18O in benthic and planktonic foraminifera in these cores are the consequence of diagenetic overgrowths of authigenic carbonates. There are multiple layers of authigenic-carbonate-rich sediment in these cores, and the stable isotope compositions of the carbonates are consistent with those formed during anaerobic oxidation of methane (AOM). The carbonate-rich layers are associated with biomarkers producedmore » by methane-oxidizing archaea, archaeol and glyceryl dibiphytanyl glyceryl tetraether (GDGT). The d13C of the archaeol and certain GDGTs are isotopically depleted. These carbonate- and AOM-biomarker-rich layers were emplaced in the SMTZ during episodes when there was a high flux of methane or methane-rich fluids upward in the sediment column. The sediment methane in the Umnak Plateau region appears to have been very dynamic during the glacial period, and interacted with the ocean-atmosphere system at millennial time scales. The upper-most carbonate-rich layers are in radiocarbon-dated sediment deposited during interstitials 2 and 3, 28-20 ka, and may be associated with the climate warming during this time.« less

Quasi-two-layer morphodynamic model for bedload-dominated problems: bed slope-induced morphological diffusion

NASA Astrophysics Data System (ADS)

Maldonado, Sergio; Borthwick, Alistair G. L.

2018-02-01

We derive a two-layer depth-averaged model of sediment transport and morphological evolution for application to bedload-dominated problems. The near-bed transport region is represented by the lower (bedload) layer which has an arbitrarily constant, vanishing thickness (of approx. 10 times the sediment particle diameter), and whose average sediment concentration is free to vary. Sediment is allowed to enter the upper layer, and hence the total load may also be simulated, provided that concentrations of suspended sediment remain low. The model conforms with established theories of bedload, and is validated satisfactorily against empirical expressions for sediment transport rates and the morphodynamic experiment of a migrating mining pit by Lee et al. (1993 J. Hydraul. Eng. 119, 64-80 (doi:10.1061/(ASCE)0733-9429(1993)119:1(64))). Investigation into the effect of a local bed gradient on bedload leads to derivation of an analytical, physically meaningful expression for morphological diffusion induced by a non-zero local bed slope. Incorporation of the proposed morphological diffusion into a conventional morphodynamic model (defined as a coupling between the shallow water equations, Exner equation and an empirical formula for bedload) improves model predictions when applied to the evolution of a mining pit, without the need either to resort to special numerical treatment of the equations or to use additional tuning parameters.

Quasi-two-layer morphodynamic model for bedload-dominated problems: bed slope-induced morphological diffusion.

PubMed

Maldonado, Sergio; Borthwick, Alistair G L

2018-02-01

We derive a two-layer depth-averaged model of sediment transport and morphological evolution for application to bedload-dominated problems. The near-bed transport region is represented by the lower (bedload) layer which has an arbitrarily constant, vanishing thickness (of approx. 10 times the sediment particle diameter), and whose average sediment concentration is free to vary. Sediment is allowed to enter the upper layer, and hence the total load may also be simulated, provided that concentrations of suspended sediment remain low. The model conforms with established theories of bedload, and is validated satisfactorily against empirical expressions for sediment transport rates and the morphodynamic experiment of a migrating mining pit by Lee et al. (1993 J. Hydraul. Eng. 119 , 64-80 (doi:10.1061/(ASCE)0733-9429(1993)119:1(64))). Investigation into the effect of a local bed gradient on bedload leads to derivation of an analytical, physically meaningful expression for morphological diffusion induced by a non-zero local bed slope. Incorporation of the proposed morphological diffusion into a conventional morphodynamic model (defined as a coupling between the shallow water equations, Exner equation and an empirical formula for bedload) improves model predictions when applied to the evolution of a mining pit, without the need either to resort to special numerical treatment of the equations or to use additional tuning parameters.

Observations of Lower Mississippi River Estuarine Dynamics: Effects of the Salt Wedge on Sediment Deposition

NASA Astrophysics Data System (ADS)

Ramirez, M. T.; Allison, M. A.

2017-12-01

The lowermost Mississippi River is subject to salt-wedge estuarine conditions during seasonally low flow, when seaward flow is unable to overcome density stratification. Previous studies in the Mississippi River salt wedge have shown the deposition of a fine sediment layer accumulating several mm/day beneath the reach where the salt wedge is present. Field studies were conducted during low flow in 2012-2015 utilizing ADCP, CTD, LISST, and physical samples to observe the physics of the salt wedge reach and to calculate rates and character of sediment trapping beneath the salt wedge. The field observations were summarized using a two-layer box-model representation of the reach to calculate water and sediment budgets entering, exiting, and stored within the reach. The salt wedge reach was found to be net depositional at rates up to 1.8 mm/day. The mechanism for transferring sediment mass from the downstream-flowing fluvial layer to the upstream-flowing marine layer appears to be flocculation, evidenced in LISST data by a spike in sediment particle diameters at the halocline. Applying reach-averaged rates of sediment trapping to a time-integrated model of salt-wedge position, we calculated annual totals ranging from 0.025 to 2.2 million tons of sediment deposited beneath the salt wedge, depending on salt-wedge persistence and upstream extent. Most years this seasonal deposit is remobilized during spring flood following the low-flow estuarine season, which may affect the timing of sediment delivery to the Gulf of Mexico, as well as particulate organic carbon, whose transport trajectory mirrors that of mineral sediment. These results are also relevant to ongoing dredging efforts necessary to maintain the economically-important navigation pathway through the lower Mississippi River, as well as planned efforts to use Mississippi River sedimentary resources to build land in the degrading Louisiana deltaic coast.

Sediment Transport over a Dredge Pit, Sandy Point Southeast, west flank of the Mississippi River during Summer Upcoast Currents: a Coupled Wave, Current and Sediment Numerical Model

NASA Astrophysics Data System (ADS)

Chaichitehrani, N.; Li, C.; Xu, K.; Bentley, S. J.; Miner, M. D.

2017-12-01

Sandy Point southeast, an elongated sand resource, was dredged in November 2012 to restore Pelican Island, Louisiana. Hydrodynamics and wave propagation patterns along with fluvial sediments from the Mississippi River influence the sediment and bottom boundary layer dynamics over Sandy Point. A state-of-the-art numerical model, Delft3D, was implemented to investigate current variations and wave transformation on Sandy Point as well as sediment transport pattern. Delft3d FLOW and WAVE modules were coupled and validated using WAVCIS and NDBC data. Sediment transport model was run by introducing both bed and river sediments, consisted of mainly mud and a small fraction of sand. A sediment transport model was evaluated for surface sediment concentration using data derived from satellite images. The model results were used to study sediment dynamics and bottom boundary layer characteristics focused on the Sandy Point area during summer. Two contrasting bathymetric configurations, with and without the Sandy Point dredge pit, were used to conduct an experiment on the sediment and bottom boundary layer dynamics. Preliminary model results showed that the presence of the Sandy Point pit has very limited effect on the hydrodynamics and wave pattern at the pit location. Sediments from the Mississippi River outlets, especially in the vicinity of the pit, get trapped in the pit under the easterly to the northeasterly upcoast current which prevails in August. We also examined the wave-induced sediment reworking and river-borne fluvial sediment over Sandy Point. The effect of wind induced orbital velocity increases the bottom shear stress compared to the time with no waves, relatively small wave heights (lower than 1.5 meters) along the deepest part of the pit (about 20 meters) causes little bottom sediment rework during this period. The results showed that in the summertime, river water is more likely the source of sedimentation in the pit.

A method for the division of the conglomerate depositional cycle under Milankovitch cycles

NASA Astrophysics Data System (ADS)

Chen, Panpan; Fang, Nianqiao; Li, Cunlei; Liu, Jianmei

2017-06-01

The conglomerate layer at the upper section of the 4th member of the Shahejie formation ({{{{S}}}4}{{u}}) of the Yongan district at the Donying depression is a well-developed sedimentation of several periods. It lacks stable muddy layers and sophisticated classification of the sedimentation periods and the proportion of sedimentary layering in each period has long been a difficult task for geologists. In addressing this problem, this paper attempts to introduce the theory of climatic cycles driven by astronomical periods from astronomical stratigraphy on the basis of the characteristics of the sedimentation under the turbidity current in the region of study. Through studying the conditions for the formation of the conglomerate layer and the factors of control, we pinpoint the formation of the layer in chronology and differentiate the cycle interface and correlation in the same formation period. Milankovitch analysis is conducted on the sedimentation of the conglomerate layer in the region of study to determine if the stratigraphy cycle of the region is primarily controlled by the eccentricity cycle and calculate MSC1 and MSC2 thicknesses of 189.3 m and 78.05 m, respectively. Milankovitch theory is the primary tool used in the analysis, in conjunction with petrographic analysis. The stratum at the {{{{S}}}4}{{u}} is classified into four IV-grade sequences and 11 V-grade sequences. The information on the dominant cycle frequency is used for wave filtering of the well logs and to determine the significant Milankovitch wave log. With the data from this curve, we may compare the stratigraphy cycle with the characteristics of the standard cycle and classify and compare the sedimentation periods of the conglomerate layers in further detail.

Structured wafer for device processing

DOEpatents

Okandan, Murat; Nielson, Gregory N

2014-05-20

A structured wafer that includes through passages is used for device processing. Each of the through passages extends from or along one surface of the structured wafer and forms a pattern on a top surface area of the structured wafer. The top surface of the structured wafer is bonded to a device layer via a release layer. Devices are processed on the device layer, and are released from the structured wafer using etchant. The through passages within the structured wafer allow the etchant to access the release layer to thereby remove the release layer.

Structured wafer for device processing

DOEpatents

Okandan, Murat; Nielson, Gregory N

2014-11-25

A structured wafer that includes through passages is used for device processing. Each of the through passages extends from or along one surface of the structured wafer and forms a pattern on a top surface area of the structured wafer. The top surface of the structured wafer is bonded to a device layer via a release layer. Devices are processed on the device layer, and are released from the structured wafer using etchant. The through passages within the structured wafer allow the etchant to access the release layer to thereby remove the release layer.

Sedimentation, bioturbation, and sedimentary fabric evolution on a modern mesotidal mudflat: A multi-tracer study of processes, rates, and scales

NASA Astrophysics Data System (ADS)

Bentley, Samuel J.; Swales, Andrew; Pyenson, Benjamin; Dawe, Justin

2014-03-01

A study of muddy tidal-flat sedimentation and bioturbation was undertaken in the Waitetuna Arm of Raglan Harbor, New Zealand, to evaluate the physical and biological processes that control cycling of sediment between the intertidal seabed and sediment-water interface, and also the formation of tidal flat sedimentary fabric and fine-scale stratigraphy. Cores were collected along an intertidal transect, and analyzed for sedimentary fabric, 210Pb and 7Be radiochemical distributions, and grain size. At the same locations, a new approach for time-series core-X-radiography study was undertaken (spanning 191 days), using magnetite-rich sand as a tracer for sedimentation and bioturbation processes in shallow tidal flat sediments. Sedimentary fabric consists of a shallow stratified layer overlying a deeper zone of intensely bioturbated shelly mud. Bioadvection mixes the deeper zone and contributes fine sediment to the surface stratified layer, via biodeposition. Physical resuspension and deposition of surface muds by wave and tidal flow are also likely contributors to formation of the surficial stratified layer, but physical stratification is not observed below this depth. The deliberate tracer study allowed calculation of bioadvection rates that control strata formation, and can be used to model diagenetic processes. Results suggest that the upper ˜15 cm of seabed can be fully mixed over timescales <1.75 y. Such mixing will erase pre-existing sedimentary fabric and transport buried sediment and chemical compounds back to the tidal-flat surface. Shallow biodiffusion also exists, but produces much slower and shallower mass transport. Best fits for 210Pb profiles using a diagenetic bioadvection/sedimentation model and independently measured tiered bioadvection rates suggest that sediment accumulation rates (SARs) on the tidal flat are ˜0.25 cm/y, near the low end of contemporary New Zealand muddy intertidal SARs. Frequent deposition and erosion of the surface layer demonstrates that long-term sediment accumulation captures only a small fraction of sediment deposited at any one time. Model results also suggest that our magnetite tracer method may slightly underestimate short-term shallow mixing rates (demonstrated by 7Be profiles), and slightly overestimate longer-term, deeper bioturbation rates (demonstrated by 210Pb profiles).

Long-term stability of crystal-stabilized water-in-oil emulsions.

PubMed

Ghosh, Supratim; Pradhan, Mamata; Patel, Tejas; Haj-Shafiei, Samira; Rousseau, Dérick

2015-12-15

The impact of cooling rate and mixing on the long-term kinetic stability of wax-stabilized water-in-oil emulsions was investigated. Four cooling/mixing protocols were investigated: cooling from 45°C to either 25°C or 4°C with/without stirring and two cooling rates - slow (1°C/min) and fast (5°C/min). The sedimentation behaviour of the emulsions was significantly affected by cooling protocol. Stirring was critical to the stability of all emulsions, with statically-cooled (no stirring) emulsions suffering from extensive aqueous phase separation. Emulsions stirred while cooling showed sedimentation of a waxy emulsion layer leaving a clear oil layer at the top, with a smaller separation and droplet size distribution at 4°C compared to 25°C, indicating the importance of the amount of crystallized wax on emulsion stability. Light microscopy revealed that crystallized wax appeared both on the droplet surface and in the continuous phase, suggesting that stirring ensured dispersibility of the water droplets during cooling as the wax was crystallizing. Wax crystallization on the droplet surface provided stability against droplet coalescence while continuous phase wax crystals minimized inter-droplet collisions. The key novel aspect of this research is in the simplicity to tailor the spatial distribution of wax crystals, i.e., either at the droplet surface or in the continuous phase via use of a surfactant and judicious stirring and/or cooling. Knowledge gained from this research can be applied to develop strategies for long-term storage stability of crystal-stabilized W/O emulsions. Copyright © 2015 Elsevier Inc. All rights reserved.

Low Reynolds number suspension gravity currents.

PubMed

Saha, Sandeep; Salin, Dominique; Talon, Laurent

2013-08-01

The extension of a gravity current in a lock-exchange problem, proceeds as square root of time in the viscous-buoyancy phase, where there is a balance between gravitational and viscous forces. In the presence of particles however, this scenario is drastically altered, because sedimentation reduces the motive gravitational force and introduces a finite distance and time at which the gravity current halts. We investigate the spreading of low Reynolds number suspension gravity currents using a novel approach based on the Lattice-Boltzmann (LB) method. The suspension is modeled as a continuous medium with a concentration-dependent viscosity. The settling of particles is simulated using a drift flux function approach that enables us to capture sudden discontinuities in particle concentration that travel as kinematic shock waves. Thereafter a numerical investigation of lock-exchange flows between pure fluids of unequal viscosity, reveals the existence of wall layers which reduce the spreading rate substantially compared to the lubrication theory prediction. In suspension gravity currents, we observe that the settling of particles leads to the formation of two additional fronts: a horizontal front near the top that descends vertically and a sediment layer at the bottom which aggrandises due to deposition of particles. Three phases are identified in the spreading process: the final corresponding to the mutual approach of the two horizontal fronts while the laterally advancing front halts indicating that the suspension current stops even before all the particles have settled. The first two regimes represent a constant and a decreasing spreading rate respectively. Finally we conduct experiments to substantiate the conclusions of our numerical and theoretical investigation.

Phylogenetic analysis of Archaea in the deep-sea sediments of west Pacific Warm Pool.

PubMed

Wang, Peng; Xiao, Xiang; Wang, Fengping

2005-06-01

Archaea are known to play important roles in carbon cycling in marine sediments. The main compositions of archaeal community in five deep-sea sediment samples collected from west Pacific Warm Pool area (WP-0, WP-1, WP-2, WP-3, WP-4), and in five sediment layers (1 cm-, 3 cm-, 6 cm-, 10 cm-, 12 cm- layer) of the 12 cm sediment core of WP-0 were checked and compared by denaturing gradient gel electrophoresis and 16 S rRNA gene sequencing. It was revealed that all the deep-sea sediment samples checked contained members of non-thermophilic marine group I crenarchaeota as the predominant archaeal group. To further detect groups of archaea possibly relating with C1 metabolism, PCR amplification was carried out using primers targeting methane-oxidizing archaea. Although no methane-oxidizing archaea was detected, a group of novel archaea (named as WPA) was instead identified from all these five WP samples by clone analysis. They could be placed in the euryarchaeota kingdom, separated into two distinct groups, the main group was peripherally related with methanogens, the other group related with Thermoplasma. The vertical distributions of WPA, archaea and bacteria along the WP-0 sediment column were determined by quantitative-PCR. It was found that bacteria dominated at all depths, the numbers of bacteria were 10-10(4) times more than those of archaea. The proportion of archaea versus bacteria had a depth related increasing tendency, it was lowest at the first layer (0.01%), reached highest at the 12 cm- layer (10%). WPA only constituted a small proportion of the archaeal community (0.05% to 5%) of west Pacific Warm Pool sediment.

Detailed seismic velocity of the incoming subducting sediments in the 2004 great Sumatra earthquake rupture zone from full waveform inversion of long offset seismic data

NASA Astrophysics Data System (ADS)

Qin, Yanfang; Singh, Satish C.

2017-04-01

The nature of incoming sediments defines the locking mechanism on the megathrust, and the development and evolution of the accretionary wedge. Here we present results from seismic full waveform inversion of 12 km long offset seismic reflection data within the trench in the 2004 Sumatra earthquake rupture zone area that provide detailed quantitative information on the incoming oceanic sediments and the trench-fill sediments. The thickness of sediments in this area is 3-4 km, and P wave velocity is as much as 4.5 km/s just above the oceanic crust, suggesting the presence of silica-rich highly compacted and lithified sediments leading to a strong coupling up to the subduction front. We also find an 70-80 m thick low-velocity layer, capped by a high-velocity layer, at 0.8 km above the subducting plate. This low-velocity layer, previously identified as high-amplitude negative polarity reflection, could have porosity of up to 30% containing overpressured fluids, which could act as a protodécollement seaward from the accretionary prism and décollement beneath the forearc. This weak protodécollement combined with the high-velocity indurated sediments above the basement possibly facilitated the rupture propagating up to the front during the 2004 earthquake and enhancing the tsunami. We also find another low-velocity layer within the sediments that may act as a secondary décollement observed offshore central Sumatra, forming bivergent pop-up structures and acting as a conveyer belt in preserving these pop-up structures in the forearc region.

Hydrothermal sediments are a source of water column Fe and Mn in the Bransfield Strait, Antarctica

NASA Astrophysics Data System (ADS)

Aquilina, Alfred; Homoky, William B.; Hawkes, Jeffrey A.; Lyons, Timothy W.; Mills, Rachel A.

2014-07-01

Short sediment cores were collected from ∼1100 m water depth at the top of Hook Ridge, a submarine volcanic edifice in the Central Basin of the Bransfield Strait, Antarctica, to assess Fe and Mn supply to the water column. Low-temperature hydrothermal fluids advect through these sediments and, in places, subsurface H2S is present at high enough concentrations to support abundant Sclerolinum sp., an infaunal tubeworm that hosts symbiotic thiotrophic bacteria. The water column is fully oxic, and oxygen penetration depths at all sites are 2-5 cmbsf. Pore water Fe and Mn content is high within the subsurface ferruginous zone (max. 565 μmol Fe L-1, >3-7 cmbsf)-14-18 times higher than values measured at a nearby, background site of equivalent water depth. Diffusion and advection of pore waters supply significant Fe and Mn to the surface sediment. Sequential extraction of the sediment demonstrates that there is a significant enrichment in a suite of reactive, authigenic Fe minerals in the upper 0-5 cm of sediment at one site characterised by weathered crusts at the seafloor. At a site with only minor authigenic mineral surface enrichment we infer that leakage of pore water Fe and Mn from the sediment leads to enriched total dissolvable Fe and Mn in bottom waters. An Eh sensor mounted on a towed package mapped a distinct Eh signature above this coring site which is dispersed over several km at the depth of Hook Ridge. We hypothesise that the main mechanism for Fe and Mn efflux from the sediment is breach of the surface oxic layer by the abundant Sclerolinum sp., along with episodic enhancements by physical mixing and resuspension of sediment in this dynamic volcanic environment. We propose that Hook Ridge sediments are an important source of Fe and Mn to the deep waters of the Central Basin in the Bransfield Strait, where concentrations are sustained by the benthic flux, and Fe is stabilised in the water column as either colloidal phases or ligand-bound dissolved species. Entrainment of this water mass into the Drake Passage and thereby the Antarctic Circumpolar Current could provide a significant metal source to this HNLC region of the Southern Ocean if mixing and upwelling occurs before removal of this metal pool to underlying sediments. Sediment-covered volcanic ridges are common within rifted margins and may play a previously overlooked role in the global Fe cycle.

Holocene evolution of the Tonle Sap Lake: valley network infill and rates of sedimentation in Cambodia's Great Lake

NASA Astrophysics Data System (ADS)

Best, J.; Darby, S. E.; Langdon, P. G.; Hackney, C. R.; Leyland, J.; Parsons, D. R.; Aalto, R. E.; Marti, M.

2017-12-01

Tonle Sap Lake, the largest freshwater lake in SE Asia (c. 120km long and 35 km wide), is a vital ecosystem that provides 40-60% of the protein for the population of Cambodia. The lake is fed by flow from the Mekong River that causes the lake rise in level by c. 8m during monsoonal and cyclone-related floods, with drainage of the lake following the monsoon. Hydropower dam construction on the Mekong River has raised concerns as to the fragility of the Tonle Sap habitat due to any changing water levels and sedimentation rates within the lake. This paper details results of sub-bottom profiling surveys of Tonle Sap Lake in October 2014 that detailed the stratigraphy of the lake and assessed rates of infill. An Innomar Parametric Echo Sounder (PES) was used to obtain c. 250 km of sub-bottom profiles, with penetration up to 15m below the lake bed at a vertical resolution of c. 0.20m. These PES profiles were linked to cores from the north of the lake and previous literature. The PES profiles reveal a network of valleys, likely LGM, with relief up to c. 15-20m, that have been infilled by a suite of Holocene sediments. The valley surface is picked out as a strong reflector throughout the lake, and displays a series of valleys that are up to c. 15m deep and commonly 50-200m wide, although some of the largest valleys are 1.2km in width. Modelling of channel network incision during LGM conditions generates landscapes consistent with our field observations. The Tonle Sap valley network is infilled by sediments that show firstly fluvial and/or subaerial slope sedimentation, and then by extensive, parallel-bedded, lacustrine sedimentation. Lastly, the top c. 1m of sedimentation is marked by a distinct basal erosional surface that can be traced over much of the Tonle Sap Lake, and that is overlain by a series of parallel PES reflections. This upper sediment layer is interpreted to represent sedimentation in the Tonle Sap lake due to sediment suspension settling but after a period of widespread erosion that generated the extensive erosion surface. This paper will detail the characteristics and interpretation of the PES facies, their correlation to cores and estimates of sedimentation rates. Dating and PES profiles indicate that infill of the lake was complete by c. 6ka and that minimal sedimentation has occurred since then, likely due to reworking by wave resuspension.

Resistivity profiling for mapping gravel layers that may control contaminant migration at the Amargosa Desert Research Site, Nevada

USGS Publications Warehouse

Lucius, Jeffrey E.; Abraham, Jared D.; Burton, Bethany L.

2008-01-01

Gaseous contaminants, including CFC 113, chloroform, and tritiated compounds, move preferentially in unsaturated subsurface gravel layers away from disposal trenches at a closed low-level radioactive waste-disposal facility in the Amargosa Desert about 17 kilometers south of Beatty, Nevada. Two distinct gravel layers are involved in contaminant transport: a thin, shallow layer between about 0.5 and 2.2 meters below the surface and a layer of variable thickness between about 15 and 30 meters below land surface. From 2003 to 2005, the U.S. Geological Survey used multielectrode DC and AC resistivity surveys to map these gravel layers. Previous core sampling indicates the fine-grained sediments generally have higher water content than the gravel layers or the sediments near the surface. The relatively higher electrical resistivity of the dry gravel layers, compared to that of the surrounding finer sediments, makes the gravel readily mappable using electrical resistivity profiling. The upper gravel layer is not easily distinguished from the very dry, fine-grained deposits at the surface. Two-dimensional resistivity models, however, clearly identify the resistive lower gravel layer, which is continuous near the facility except to the southeast. Multielectrode resistivity surveys provide a practical noninvasive method to image hydrogeologic features in the arid environment of the Amargosa Desert.

Microfossil biostratigraphy of prograding Neogene platform-margin carbonates, Bahamas: Age constraints and alternatives

USGS Publications Warehouse

Lidz, B.H.; Bralower, T.J.

1994-01-01

Benthic and planktic foraminifera and calcareous nannofossils were recovered in shallow-water carbonate rock cores from two continuous boreholes drilled 7.5 km apart on the west platform margin of the Great Bahama Bank. The microfossils define six biostratigraphic units in each hole. One unit in each hole represents a correlative condensed section. Seven foraminiferal biozones are recognized in 11 of the units between the holes: middle Miocene Globorotalia fohsi robusta Zone N12, late Miocene G. acostaensis Zone N16 and G. humerosa Zone N17, early Pliocene G. margaritae evoluta Subzone N19, late Pliocene G. exilis Subzone N21 and, tentatively, G. tosaensis tosaensis Zone N21, and early Pleistocene G. crassaformis viola Subzone N22. The twelfth unit is inferred to be of G. crassaformis viola Subzone N22 age. The oldest unit is onshore, the youngest is offshore. As presently interpreted, the nannofossil and foraminiferal zonations are partially correlative. Although the microfossils unequivocally constrain the series ages of the sediments, the incompleteness of the fossil record allows for alternative biozonal age models within the series. The Miocene and Pliocene biozones are common to both holes, but the greatest similarities between the holes are the significant mixing of middle and late Miocene, and late Miocene-early Pliocene faunas, the greatly condensed intervals at the Miocene/Pliocene boundary, and the early Pliocene influx of deep-water benthic and pelagic foraminifera. Of particular importance is the tentative recognition of late Pliocene G. tosaensis tosaensis Zone N21 in one borehole. Subsequent data not available to this phase of the study indicate that much of the zone is likely missing. Its absence will lend support to speculations of a regional unconformity in the Bahamas. The microfossils indicate that (1) several transgressions occurred from the middle Miocene to at least the earliest Pleistocene (> 11.5-> 0.46 Ma), during which banktop-derived sediments accumulating at the margin prograded the platform seaward; (2) a condensed interval on the bank top may represent a late Miocene lowstand, a period of sediment bypassing, or a lack of accommodation space; (3) the slope received thin layers of pelagic sediments in a condensed interval during the late Miocene and early Pliocene, while the bank top accommodated early Pliocene (4.2-3.4 Ma) deep-water indicators prior to a likely period of exposure (2.35 - 1.89 Ma); (4) two cycles of banktop sediment production and starvation occurred during the Pliocene; (5) the Pliocene transgression was punctuated by stillstands or low-amplitude reversals during which parts of biozones did not accumulate; and (6) the sediments containing the most complete microfossil-datum record are the thin pelagic strata that mark interruptions in the regular shedding of transgressive deposits from the platform. Sedimentation-rate patterns varied but were generally higher offshore than onshore. ?? 1994.

Experimental and theoretical investigation of the role of clay in subaqueous sediment flows and its effect on run-out distance

NASA Astrophysics Data System (ADS)

Hermidas, Navid; Luthi, Stefan; Eggenhuisen, Joris; Silva Jacinto, Ricardo; Toth, Ferenc; Pohl, Florian; de Leeuw, Jan

2016-04-01

Debris flows are driven by gravity, which in the tail region is overcome by the yield strength of the flow, forcing it to freeze. These flows are capable of achieving staggeringly large run-out distances on low gradients. The case in point, described in previous publications, is the flow which resulted in the deposit of Bed 5 of the Agadir megaslide on the north-west African margin. Debrites of this flow have been recorded several hundred kilometres away from the original landslide. Previous studies have attributed such long run-out distances to hydroplaning, low yield strength, and flow transformation. It is known that the net force acting on a volume of fluid in equilibrium is zero. In this work we show that clay-laden flows are capable of approaching equilibrium. The flows which can achieve the maximum run-out distance are cohesive enough to resist some of the surrounding disturbances, that can upset the equilibrium, and reach close to equilibrium conditions, yet are dilute enough to have low viscous stress, and relatively low yield strength and lose little sediment due to deposition. A flow that is not in equilibrium will always seek to approach equilibrium conditions by speeding up or slowing down, depositing sediment, eroding the substrate, contracting in the form of the tail approaching the head, stretching, entraining water and growing in height, or dewatering and collapsing. Here we present a theory that shows that two dimensional (2D) flows in equilibrium do not grow in height. 2D flume experiments were conducted on different mixtures of kaolinite, sand, silt, and water, on varying slopes and a transitionally rough bed (sand glued), and using various discharge rates, in order to map out different stages in the evolution of a density flow from a cohesive plug flow into a turbidity current. The following flow types were observed: high density turbidity currents, plug flows, and no flow. From the velocity profiles, certain runs demonstrated close to equilibrium behaviour. For these flows, very little flow height growth and velocity variation was observed over the length of the flume. In all cases the flow appeared to be laminar within the boundary layer with Kelvin-Helmholtz instabilities at the top which were suppressed to a large extent for higher sediment concentrations. A deposit consisting of thick muddy sand, with approximately uniform thickness, was observed for higher sediment concentrations, indicating relatively higher yield strength values, while a thinner more sandy deposit was observed for more dilute flows. It was concluded that high sediment concentrations on more moderate slopes result in slower moving plug flows which are capable of suppressing turbulence at the top, while lower sediment concentrations on steeper slopes result in faster moving, more turbulent currents. The flows which can achieve the largest run-out distance are located between these two extremes.

Spiders on Mounds

NASA Image and Video Library

2016-12-21

This terrain looks like lumpy sediment on top of patterned ground. The lumpy sediment is likely just loosely consolidated because it is covered with spidery channels. This landform is uniquely Martian, formed in the spring as seasonal dry ice turns directly into gas that erodes channels in the surface. http://photojournal.jpl.nasa.gov/catalog/PIA14452

The distribution of sediments grain size along the depth in source of the Yangtze River, Tibetan Plateau, China

NASA Astrophysics Data System (ADS)

Zhou, Y.; Yao, S.; Zhou, S.; Liu, X.; Yan, X.; Lu, J.

2017-12-01

Sediment was the one result of river process, in alluvial rive, it can reflect the hydrodynamic characteristic, even the hydrology and climate. In the source region of the Yangtze River with few human activities, The Qumalai Reach of the Tongtianhe River was selected to research the distribution of sediments grain size along the depth. The vertical drilling tools were used to obtain 7 boreholes along the river cross section, and the sedimentary cores were made analysis of stratification and granularity. The results show: The sediments are dominated by sand and grail, the sediment transport capacity of river sources is strong; the grain size frequency distribution curve with 2 3 kurtosis, main peak is sharp, it is typical deposit sediment of the suspended load; The grain size coarsen from the stream terrace to the main channel, sediment transport capacity of main stream is bigger; There are several coarse and fine sediments layers in the sedimentary core of the terrace and flood plain, medium diameters of each layer are various from 0.4mm to 80mm, different layer with different grain size can reflect the different hydrodynamic characteristic of each historical period. This result can provide the original data and enlightenment to support the research for historical river process and hydrology so much as the climate change.

Microbial Iron(II) Oxidation in Littoral Freshwater Lake Sediment: The Potential for Competition between Phototrophic vs. Nitrate-Reducing Iron(II)-Oxidizers

PubMed Central

Melton, E. D.; Schmidt, C.; Kappler, A.

2012-01-01

The distribution of neutrophilic microbial iron oxidation is mainly determined by local gradients of oxygen, light, nitrate and ferrous iron. In the anoxic top part of littoral freshwater lake sediment, nitrate-reducing and phototrophic Fe(II)-oxidizers compete for the same e− donor; reduced iron. It is not yet understood how these microbes co-exist in the sediment and what role they play in the Fe cycle. We show that both metabolic types of anaerobic Fe(II)-oxidizing microorganisms are present in the same sediment layer directly beneath the oxic-anoxic sediment interface. The photoferrotrophic most probable number counted 3.4·105 cells·g−1 and the autotrophic and mixotrophic nitrate-reducing Fe(II)-oxidizers totaled 1.8·104 and 4.5·104 cells·g−1 dry weight sediment, respectively. To distinguish between the two microbial Fe(II) oxidation processes and assess their individual contribution to the sedimentary Fe cycle, littoral lake sediment was incubated in microcosm experiments. Nitrate-reducing Fe(II)-oxidizing bacteria exhibited a higher maximum Fe(II) oxidation rate per cell, in both pure cultures and microcosms, than photoferrotrophs. In microcosms, photoferrotrophs instantly started oxidizing Fe(II), whilst nitrate-reducing Fe(II)-oxidizers showed a significant lag-phase during which they probably use organics as e− donor before initiating Fe(II) oxidation. This suggests that they will be outcompeted by phototrophic Fe(II)-oxidizers during optimal light conditions; as phototrophs deplete Fe(II) before nitrate-reducing Fe(II)-oxidizers start Fe(II) oxidation. Thus, the co-existence of the two anaerobic Fe(II)-oxidizers may be possible due to a niche space separation in time by the day-night cycle, where nitrate-reducing Fe(II)-oxidizers oxidize Fe(II) during darkness and phototrophs play a dominant role in Fe(II) oxidation during daylight. Furthermore, metabolic flexibility of Fe(II)-oxidizing microbes may play a paramount role in the conservation of the sedimentary Fe cycle. PMID:22666221

Technogenic and natural radionuclides in the bottom sediments of the Sea of Azov: regularities of distribution and application to the study of pollutants accumulation chronology

NASA Astrophysics Data System (ADS)

Kuznetsov, A. N.; Fedorov, Yu A.; Yaroslavtsev, V. M.

2018-01-01

The study of pollutants vertical distribution in seabed sediments is of high interest as they conserve the information on the chronology of pollution level in the past. In the present paper, the results of layer by layer study of Cs-137, Am-241, Pb-210 specific activities as well as concentrations of petroleum components, lead and mercury in 48 sediment cores of the Sea of Azov, the Don River and the Kuban River are examined. In most sediment cores, two peaks of Cs-137 and Am-241 are detected. The upper of them was formed due to the Chernobyl accident in 1986 and the other is related to the global nuclear fallout of 1960s. The specific activity of naturally occurring atmospheric Lead-210 decreases exponentially with the sediment core depth. However, it is influenced by fluvial run-off, coastal erosion, Radium-226 and Radon-222 decay. The data on the radionuclides distribution in the seabed sediments is used to date them. According to the results of dating, most of petroleum components, lead and mercury quantities are concentrated in the upper sediment layer formed in the last 50 to 70 years i.e. in the period of the most important anthropogenic pressure.

CO2 leakage from carbon dioxide capture and storage (CCS) systems affects organic matter cycling in surface marine sediments.

PubMed

Rastelli, Eugenio; Corinaldesi, Cinzia; Dell'Anno, Antonio; Amaro, Teresa; Greco, Silvestro; Lo Martire, Marco; Carugati, Laura; Queirós, Ana M; Widdicombe, Stephen; Danovaro, Roberto

2016-12-01

Carbon dioxide capture and storage (CCS), involving the injection of CO 2 into the sub-seabed, is being promoted worldwide as a feasible option for reducing the anthropogenic CO 2 emissions into the atmosphere. However, the effects on the marine ecosystems of potential CO 2 leakages originating from these storage sites have only recently received scientific attention, and little information is available on the possible impacts of the resulting CO 2 -enriched seawater plumes on the surrounding benthic ecosystem. In the present study, we conducted a 20-weeks mesocosm experiment exposing coastal sediments to CO 2 -enriched seawater (at 5000 or 20,000 ppm), to test the effects on the microbial enzymatic activities responsible for the decomposition and turnover of the sedimentary organic matter in surface sediments down to 15 cm depth. Our results indicate that the exposure to high-CO 2 concentrations reduced significantly the enzymatic activities in the top 5 cm of sediments, but had no effects on subsurface sediment horizons (from 5 to 15 cm depth). In the surface sediments, both 5000 and 20,000 ppm CO 2 treatments determined a progressive decrease over time in the protein degradation (up to 80%). Conversely, the degradation rates of carbohydrates and organic phosphorous remained unaltered in the first 2 weeks, but decreased significantly (up to 50%) in the longer term when exposed at 20,000 ppm of CO 2 . Such effects were associated with a significant change in the composition of the biopolymeric carbon (due to the accumulation of proteins over time in sediments exposed to high-pCO 2 treatments), and a significant decrease (∼20-50% at 5000 and 20,000 ppm respectively) in nitrogen regeneration. We conclude that in areas immediately surrounding an active and long-lasting leak of CO 2 from CCS reservoirs, organic matter cycling would be significantly impacted in the surface sediment layers. The evidence of negligible impacts on the deeper sediments should be considered with caution and further investigated simulating the intrusion of CO 2 from a subsurface source, as occurring during real CO 2 leakages from CCS sites. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evidence for sub-lacustrine volcanic activity in Lake Bolsena (central Italy) revealed by high resolution seismic data sets

NASA Astrophysics Data System (ADS)

Lindhorst, Katja; Krastel, Sebastian; Wagner, Bernd; Schuerer, Anke

2017-06-01

The Bolsena caldera that formed between 0.6 and 0.2 Ma has a well preserved structural rim, which makes it an ideal site to study the tectonic and volcanic evolution of calderas. However, the main area is covered by a 150 m deep lake which makes it rather difficult to investigate the subsurface structure directly. To overcome this problem new high resolution hydro-acoustic surveys using a multichannel reflection seismic system and a sediment echo-sounder system were conducted in September 2012. As space was limited we used a rowing boat towed by a rubber boat to handle a 36 m long and 24 channel streamer to receive seismic reflections produced using a Mini GI-Gun (0.25 l). The subsurface structure of Lake Bolsena was imaged up to a sediment depth of 190 m, which is estimated to have filled over a period of 333 kyrs. However, massive pyroclastic flow deposits found in the deeper parts of the basin indicate an initial infill of volcanic deposits from two adjacent younger calderas, the Latera (W) and Montefiascone (SE) calderas. Our data suggest that the caldera has a long history of active volcanism, because the lacustrine sediments show post-sedimentary influences of geothermal fluids. We mapped several mound structures at various stratigraphic depths. Two volcanic structures outcrop at the modern lake surface implying recent activity. One of these structures is hardly covered by sediments and has a crater-like feature in its summit. The other structure shows a pockmark-like depression on top. Another observable feature is a partially sediment filled crater located in the western part of the lake which further implies the existence of a magma chamber located beneath the Bolsena caldera. Since the late Pleistocene and Holocene, the sedimentation was mainly hemipelagic evidenced by a sediment drape of up to 10 m thick sediment drape on the uppermost sediments. Beneath the drape we found evidence for a distal tephra layer likely related to an explosive eruption from the Campanian Volcanic Province occurring as the Neapolitan Yellow Tuff. Our new geophysical data set is a valuable record with a potential to constrain the sedimentary and volcanic evolution of the Vulsini Volcanic District in areas that have not been assessed previously due to logistical challenges of conducting surveys in water-filled settings.

Sediment resuspension characteristics in Baltimore Harbor, Maryland

USGS Publications Warehouse

Maa, J.P.-Y.; Sanford, L.; Halka, J.P.

1998-01-01

Critical bed shear stress for sediment resuspension and sediment erosion rate were measured in-situ at sites from inner to outer Baltimore Harbor using the VIMS Sea Carousel. Clay mineral contents and biological conditions were almost the same at the four study sites. The experimental results indicated that the erosion rate increased from the outer harbor toward the inner harbor with a maximum difference of about 10 times at an excess bed shear stress of 0.1 Pa. The measured critical bed shear stress strongly depended on the existence of a fluff layer. It was approximately 0.05 Pa if a fluff layer existed, and increases to about 0.1 Pa in the absence of a fluff layer.

Benthic boundary layer processes in the Lower Florida Keys

USGS Publications Warehouse

Lavoie, D.L.; Richardson, M.D.; Holmes, C.

1997-01-01

This special issue of Geo-Marine Letters, "Benthic Boundary Layer Processes in the Lower Florida Keys," includes 12 papers that present preliminary results from the Key West Campaign. The Dry Tortugas and Marquesas Keys test sites were selected by a group of 115 scientists and technicians to study benthic boundary layer processes in a carbonate environment controlled by bioturbation and biogeochemical processes. Major activities included remote sediment classification; high-frequency acoustic scattering experiments; sediment sampling for radiological, geotechnical, biological, biogeochemical, physical, and geoacoustic studies; and hydrodynamic studies using an instrumented tetrapod. All these data are being used to improve our understanding of the effects of environmental processes on sediment structure and behavior.

Transport and transformation of nutrients and sediment in two agricultural watersheds in northeast Arkansas

USDA-ARS?s Scientific Manuscript database

Agriculture is vital to Arkansas economy as it contributes $20 billion annually, double the average national contribution to the state GDP. Arkansas is ranked in the top 5 in rice, cotton seed and sorghum, and top 20 in soybean, corn for grain, and wheat production nationally. Despite the importance...

Density-dependent groundwater flow and dissolution potential along a salt diapir in the Transylvanian Basin, Romania

NASA Astrophysics Data System (ADS)

Zechner, Eric; Danchiv, Alex; Dresmann, Horst; Mocuţa, Marius; Huggenberger, Peter; Scheidler, Stefan; Wiesmeier, Stefan; Popa, Iulian; Zlibut, Alexandru; Zamfirescu, Florian

2016-04-01

Salt diapirs and the surrounding sediments are often involved in a variety of human activities, such as salt mining, exploration and storage of hydrocarbons, and also storage of radioactive waste material. The presence of highly soluble evaporitic rocks, a complex tectonic setting related to salt diapirsm, and human activities can lead to significant environmental problems, e.g. land subsidence, sinkhole development, salt cavern collapse, and contamination of water resources with brines. In the Transylvanian town of Ocna Mures. rock salt of a near-surface diapir has been explored since the Roman ages in open excavations, and up to the 20th century in galleries and with solution mining. Most recently, in 2010 a sudden collapse in the adjacent Quaternary unconsolidated sediments led to the formation of a 70-90m wide salt lake with a max. depth of 23m. Over the last 3 years a Romanian-Swiss research project has led to the development of 3D geological and hydrogeological information systems in order to improve knowledge on possible hazards related to uncontrolled salt dissolution. One aspect which has been investigated is the possibility of density-driven flow along permeable subvertical zones next to the salt dome, and the potential for subsaturated groundwater to dissolve the upper sides of the diapir. Structural 3D models of the salt diapir, the adjacent basin sediments, and the mining galleries, led to the development of 2D numerical vertical density-dependent models of flow and transport along the diapir. Results show that (1) increased rock permeability due to diapirsm, regional tectonic thrusting and previous dissolution, and (2) more permeable sandstone layers within the adjacent basin sediments may lead to freshwater intrusion towards the top of the diapir, and, therefore, to increased potential for salt dissolution.

Splay Fault Branching from the Hikurangi Subduction Shear Zone: Implications for Slow Slip and Fluid Flow

NASA Astrophysics Data System (ADS)

Henrys, S. A.; Plaza-Faverola, A. A.; Pecher, I. A.; Klaeschen, D.; Wallace, L.

2016-12-01

Seismic reflection data along the East Coast of the New Zealand North Island are used to map the offshore character and geometry of the central Hikurangi subduction thrust and outer wedge in a region of short term ( 2-3 weeks duration) geodetically determined slow-slip events (SSEs). Pre-stack depth migration of line 05CM-38 was used to derive subducting slab geometry and upper crustal structure together with a Vp image of the crust that is resolved to 14 km depth. The subduction interface is a shallow dipping thrust at < 7 km deep near the trench and steps down to 14 km depth along an approximately 18 km long ramp, beneath Porangahau Ridge. This bend in the subducted plate is associated with splay fault branching and coincides with the zone of maximum slip (90 mm) inferred on the subduction interface during slow slip events in June and July 2011. We infer that the step down in the décollement transfers slip on the plate interface from the top of subducting sediments to the oceanic crust and drives underplating beneath the inner margin of central Hikurangi margin. Low-velocity subducting sediments (LVZ) beneath the plate interface, updip of the plate interface ramp, are interpreted as being capped with a low permeability condensed layer of chalk and interbedded mudstones. We interpret this LVZ as fluid-rich overpressured sediments that have been displaced and later imbricated by splay faults in a region that may mark the up-dip transition from seismic to aseismic behavior. Further, we hypothesize that fluids derived from the overpressured sediment are channeled along splay faults to the shallow sub-seafloor near Porangahau Ridge where seafloor seepage and an upwarping of the gas hydrate Bottom-Simulating Reflector have been documented.

GDGT and alkenone flux in the northern Gulf of Mexico: Implications for the TEX86 and UK'37 paleothermometers

NASA Astrophysics Data System (ADS)

Richey, Julie N.; Tierney, Jessica E.

2016-12-01

The TEX86 and U37K' molecular biomarker proxies have been broadly applied in downcore marine sediments to reconstruct past sea surface temperature (SST). Although both TEX86 and U37K' have been interpreted as proxies for mean annual SST throughout the global ocean, regional studies of glycerol dibiphytanyl glycerol tetraethers (GDGTs) and alkenones in sinking particles are required to understand the influence of seasonality, depth distribution, and diagenesis on downcore variability. We measure GDGT and alkenone flux, as well as the TEX86 and U37K' indices in a 4 year sediment trap time series (2010-2014) in the northern Gulf of Mexico (nGoM), and compare these data with core-top sediments at the same location. GDGT and alkenone fluxes do not show a consistent seasonal cycle; however, the largest flux peaks for both occurs in winter. U37K' covaries with SST over the 4 year sampling interval, but the U37K'-SST relationship in this data set implies a smaller slope or nonlinearity at high temperatures when compared with existing calibrations. Furthermore, the flux-weighted U37K' value from sinking particles is significantly lower than that of underlying core-top sediments, suggesting preferential diagenetic loss of the tri-unsaturated alkenone in sediments. TEX86 does not covary with SST, suggesting production in the subsurface upper water column. The flux-weighted mean TEX86 matches that of core-top sediments, confirming that TEX86 in the nGoM reflects local planktonic production rather than allochthonous or in situ sedimentary production. We explore potential sources of uncertainty in both proxies in the nGoM but demonstrate that they show nearly identical trends in twentieth century SST, despite these factors.

Erosion Characteristics and Horizontal Variability for Small Erosion Depths in the Sacramento - San Joaquin River Delta, California, USA

NASA Astrophysics Data System (ADS)

Schoellhamer, D. H.; Manning, A. J.; Work, P. A.

2015-12-01

Cohesive sediment in the Sacramento-San Joaquin River Delta affects pelagic fish habitat, contaminant transport, and marsh accretion. Observations of suspended-sediment concentration in the delta indicate that about 0.05 to 0.20 kg/m2 are eroded from the bed during a tidal cycle. If erosion is horizontally uniform, the erosion depth is about 30 to 150 microns, the typical range in diameter of suspended flocs. Application of an erosion microcosm produces similarly small erosion depths. In addition, core erodibility in the microcosm calculated with a horizontally homogeneous model increases with depth, contrary to expectations for a consolidating bed, possibly because the eroding surface area increases as applied shear stress increases. Thus, field observations and microcosm experiments, combined with visual observation of horizontally varying biota and texture at the surface of sediment cores, indicate that a conceptual model of erosion that includes horizontally varying properties may be more appropriate than assuming horizontally homogeneous erosive properties. To test this hypothesis, we collected five cores and measured the horizontal variability of shear strength within each core in the top 5.08 cm with a shear vane. Small tubes built by a freshwater worm and macroalgae were observed on the surface of all cores. The shear vane was inserted into the sediment until the top of the vane was at the top of the sediment, torque was applied to the vane until the sediment failed and the vane rotated, and the corresponding dial reading in Nm was recorded. The dial reading was assumed to be proportional to the surface strength. The horizontal standard deviation of the critical shear stress was about 30% of the mean. Results of the shear vane test provide empirical evidence that surface strength of the bed varies horizontally. A numerical simulation of erosion with an areally heterogeneous bed reproduced erosion characteristics observed in the microcosm.

A Mechanism for Stratifying Lava Flows

NASA Astrophysics Data System (ADS)

Rice, A.

2005-12-01

Relict lava flows (e.g., komatiites) are often reported to be zoned in the vertical, each zone separated by a sharp contact. Such stratifications in igneous flows, both intrusive and extrusive, can be treated as analogues of suspended loads of sediments in rivers and streams, and hence amenable to quantitative treatment derived for the hydraulic environment as long as dynamic similitude is assured. Situations typically encountered in the hydraulic environment are streams carrying a bed load at the bottom of the stream, the bed load separated by a sharp horizon from a sediment load carried above it. This sediment load may be topped by others of decreasing density as one moves to the surface of the flow, with perhaps the uppermost layer clear of any suspended matter. Rules exist for estimating the thickness D of these loads: one of them is given by D ~ 4.4V3/rgcvs where V is the shear velocity or average velocity of the flow, r = (ρs - ρl)/ρl where ρs is the density of the suspended solid matter, ρl the density of the fluid, g the acceleration of gravity, c the concentration of the particulate content and vs the settling velocity. The settling velocity is secured through Stoke's Law and the velocity of the flow is given by V = R2/3S1/2/n where R is the hydraulic radius, S the gradient along which the fluid flows and n is the Manning Coefficient. In the igneous case, the bed load would be composed of primocrysts, i.e., of the first crystals to come out of solution as the flow cools along its run. This would leave the upper portions of the flow more evolved except perhaps for a quenched crust riding atop the flow. As the viscosity of the flow is dependent not only on temperature but on composition and crystal content, the mean velocity of each layer will be different from the layer above and below it. This requires shear at the interface of adjoining stratifications, which brings into play another mechanism: dispersive pressure (the Bagnold effect). Dispersive pressure will drive primocrysts into boundary layers such as that attending the bottom of the flow and at those separating stratifications. For instance, if the primocrysts were spinals, then a Cr high might be expected at the interfaces separating stratifications. Since the melt throughout is evolving as it moves down stream, compositional variations along strike (as well is in the vertical) might be expected. Application of the above notions falls within the confines of field observation.

Modeling Small-Scale Nearshore Processes

NASA Astrophysics Data System (ADS)

Slinn, D.; Holland, T.; Puleo, J.; Puleo, J.; Hanes, D.

2001-12-01

In recent years advances in high performance computing have made it possible to gain new qualitative and quantitative insights into the behavior and effects of coastal processes using high-resolution physical-mathematical models. The Coastal Dynamics program at the U.S. Office of Naval Research under the guidance of Dr. Thomas Kinder has encouraged collaboration between modelers, theoreticians, and field and laboratory experimentalists and supported innovative modeling efforts to examine a wide range of nearshore processes. An area of emphasis has been small-scale, time-dependent, turbulent flows, such as the wave bottom boundary layer, breaking surface waves, and the swash zone and their effects on shoaling waves, mean currents, and sediment transport that integrate to impact the long-term and large-scale response of the beach system to changing environmental conditions. Examples of small-scale modeling studies supported by CD-321 related to our work include simulation of the wave bottom boundary layer. Under mild wave field conditions the seabed forms sand ripples and simulations demonstrate that the ripples cause increases in the bed friction, the kinetic energy dissipation rates, the boundary layer thickness, and turbulence in the water column. Under energetic wave field conditions the ripples are sheared smooth and sheet flow conditions can predominate, causing the top few layers of sand grains to move as a fluidized bed, making large aggregate contributions to sediment transport. Complementary models of aspects of these processes have been developed simultaneously in various directions (e.g., Jenkins and Hanes, JFM 1998; Drake and Calantoni, 2001; Trowbridge and Madsen, JGR, 1984). Insight into near-bed fluid-sediment interactions has also been advanced using Navier-Stokes based models of swash events. Our recent laboratory experiments at the Waterways Experiment Station demonstrate that volume-of-fluid models can predict salient features of swash uprush-backwash interactions under controlled conditions. While much has been achieved towards understanding the intricacies of these natural systems using nonlinear models, many questions remain to challenge future engineers and scientists. During his tenure at ONR, Tom Kinder has championed the importance of nearshore science and increased resources within the area, made accomplishments visible to the broader ocean community, increased communication between researchers through comprehensive initiatives, field experiments and workshops, helped develop 10 year plans focusing future priorities, maintained a stable environment for researchers, and encouraged them to tackle the hardest (most interesting) problems and to develop new tools along the way with which to solve them.

Ferromagnetic resonance investigation in as-prepared NiFe/FeMn/NiFe trilayer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan, S. J.; Xu, K.; Yu, L. M.

2007-06-01

NiFe/FeMn/NiFe trilayer prepared by dc magnetron sputtering was systematically investigated by ferromagnetic resonance technique (FMR) at room temperature. For NiFe/FeMn/NiFe trilayer, there are two distinct resonance peaks both in in-plane and out-of-plane FMR spectra, which are attributed to the two NiFe layers, respectively. The isotropic in-plane resonance field shift is negative for the bottom NiFe layer, while positive for the top NiFe layer. And, such phenomena result from the negative interfacial perpendicular anisotropy at the bottom NiFe/FeMn interface and positive interfacial perpendicular anisotropy at the top FeMn/NiFe interface. The linewidth of the bottom NiFe layer is larger than that ofmore » the top NiFe layer, which might be related to the greater exchange coupling at the bottom NiFe/FeMn interface.« less

Bottom Penetration at Shallow Grazing Angles II

DTIC Science & Technology

1992-06-19

Millwater , "Wave Reflection from a Sediment Layer with Depth-Dependent Properties," J. Acoust. Soc. Am. 77, 1781- 1788 (1985). 35 8. N. P. Chotiros, ’High...Acoust. Soc. Am. 8B1 S131 (1990). 12. M. Stern, A. Bedford, and H. R. Millwater , "Wave Reflection from a Sediment Layer with Depth-Dependent

Current-induced switching in CoGa/L10 MnGa/(CoGa)/Pt structure with different thicknesses

NASA Astrophysics Data System (ADS)

Ranjbar, R.; Suzuki, K. Z.; Mizukami, S.

2018-06-01

In this paper, we present the results of our study into current-induced spin-orbit torque (SOT) switching in perpendicularly magnetized CoGa/MnGa/Pt trilayers with different thicknesses of MnGa and Pt. The SOT switching was observed for all films that undergo Joule heating. We also investigate SOT switching in the bottom (CoGa)/MnGa/top(CoGa/Pt) films with different top layers. Although both the bottom and top layers contribute to the SOT, the relative magnitudes of the switching current densities JC in the top and bottom layers indicate that the SOT is dominant in the top layer. The JC as a function of thickness is discussed in terms of the magnetic properties and resistivity. Experimental data suggested that the MnGa thickness dependence of JC may originate from the perpendicular magnetic anisotropy thickness product Kueff t value. On the other hand, JC as a function of the Pt thickness shows weak dependence. This may be attributed to the slight change of spin-Hall angle θSH value with different thicknesses of Pt, when we assumed that the SOT switching is primarily due to the spin-Hall effect.

Seabed roughness parameters from joint backscatter and reflection inversion at the Malta Plateau.

PubMed

Steininger, Gavin; Holland, Charles W; Dosso, Stan E; Dettmer, Jan

2013-09-01

This paper presents estimates of seabed roughness and geoacoustic parameters and uncertainties on the Malta Plateau, Mediterranean Sea, by joint Bayesian inversion of mono-static backscatter and spherical wave reflection-coefficient data. The data are modeled using homogeneous fluid sediment layers overlying an elastic basement. The scattering model assumes a randomly rough water-sediment interface with a von Karman roughness power spectrum. Scattering and reflection data are inverted simultaneously using a population of interacting Markov chains to sample roughness and geoacoustic parameters as well as residual error parameters. Trans-dimensional sampling is applied to treat the number of sediment layers and the order (zeroth or first) of an autoregressive error model (to represent potential residual correlation) as unknowns. Results are considered in terms of marginal posterior probability profiles and distributions, which quantify the effective data information content to resolve scattering/geoacoustic structure. Results indicate well-defined scattering (roughness) parameters in good agreement with existing measurements, and a multi-layer sediment profile over a high-speed (elastic) basement, consistent with independent knowledge of sand layers over limestone.

Research on spatial distribution of photosynthetic characteristics of Winter Wheat

NASA Astrophysics Data System (ADS)

Yan, Q. Q.; Zhou, Q. Y.; Zhang, B. Z.; Han, X.; Han, N. N.; Li, S. M.

2018-03-01

In order to explore the spatial distribution of photosynthetic characteristics of winter wheat leaf, the photosynthetic rate on different parts of leaf (leaf base-leaf middle-leaf apex) and that on each canopy (top layer-middle layer-bottom layer) leaf during the whole growth period of winter wheat were measured. The variation of photosynthetic rate with PAR and the spatial distribution of winter wheat leaf during the whole growth periods were analysed. The results showed that the photosynthetic rate of different parts of winter wheat increased with the increase of PAR, which was showed as leaf base>leaf middle>leaf apex. In the same growth period, photosynthetic rate in different parts of the tablet was showed as leaf middle>leaf base>leaf apex. For the different canopy layer of winter wheat, the photosynthetic rate of the top layer leaf was significantly greater than that of the middle layer and lower layer leaf. The photosynthetic rate of the top layer leaf was the largest in the leaf base position. The photosynthetic rate of leaf of the same canopy layer at different growth stages were showed as tasseling stage >grain filling stage > maturation stage.

The volume of fine sediment in pools: An index of sediment supply in gravel-bed streams

Treesearch

Thomas E. Lisle; Sue Hilton

1992-01-01

Abstract - During waning flood flows in gravel-bed streams, fine-grained bedload sediment (sand and fine gravel) is commonly winnowed from zones of high shear stress, such as riffles, and deposited in pools, where it mantles an underlying coarse layer. As sediment load increases, more fine sediment becomes availabe to fill pools. The volume of fine sediment in pools...

Kerr microscopy study of exchange-coupled FePt/Fe exchange spring magnets

NASA Astrophysics Data System (ADS)

Hussain, Zaineb; Kumar, Dileep; Reddy, V. Raghavendra; Gupta, Ajay

2017-05-01

Magnetization reversal and magnetic microstructure of top soft magnetic layer (Fe) in exchange spring coupled L10 FePt/Fe is studied using high resolution Kerr microscopy. With remnant state of the hard magnetic layer (L10 FePt) as initial condition, magnetization loops along with magnetic domains are recorded for the top soft magnetic layer (Fe) using Kerr microscopy. Considerable shifting of Fe layer hysteresis loop from center which is similar to exchange bias phenomena is observed. It is also observed that one can tune the magnitude of hysteresis shift by reaching the remanent state from different saturating fields (HSAT) and also by varying the angle between measuring field and HSAT. The hysteresis loops and magnetic domains of top soft Fe layer demonstrate unambiguously that soft magnetic layer at remanent state in such exchange coupled system is having unidirectional anisotropy. An analogy is drawn and the observations are explained in terms of established model of exchange bias phenomena framed for field-cooled ferromagnetic - antiferromagnetic bilayer systems.

Tracing subducted sediment inputs to the Ryukyu arc-Okinawa Trough system: Evidence from thallium isotopes

NASA Astrophysics Data System (ADS)

Shu, Yunchao; Nielsen, Sune G.; Zeng, Zhigang; Shinjo, Ryuichi; Blusztajn, Jerzy; Wang, Xiaoyuan; Chen, Shuai

2017-11-01

Sediments are actively subducted in virtually every arc worldwide. However, quantifying their contributions to arc lavas and thereby establishing budgets of how sediments participate in slab-mantle interaction is challenging. In this contribution we use thallium (Tl) abundances and isotopic compositions of lavas from the Ryukyu arc (including south Kyushu) and its back-arc basin, Okinawa Trough, to investigate the influence of sediments from arc to back-arc. We also present extensive geochemical data for sediments and altered oceanic crust (AOC) outboard of the northern (DSDP Sites 296, 442B, 443 and 444) and central (DSDP Sites 294 and 295) part of the Ryukyu arc. The Tl isotopic compositions of sediments change systematically from lighter outboard of northern Ryukyu arc to heavier outboard of central Ryukyu arc. The feature reflects the dominance of terrigenous material and pelagic sedimentation outboard of the northern and central Ryukyu arc, respectively. Central and northern sections of Ryukyu arc and Okinawa Trough display larger range of Tl isotopic variation than southern section, which is consistent with more pelagic provenance for sediments outboard of central and northern Ryukyu arcs than that of expected sediments outboard of southern Ryukyu arc. Identical Tl, Sr, Nd and Pb isotope variations are found when comparing arc and back arc lavas, which indicates that sediments fluxes also account for the Tl isotopic variations in the Okinawa Trough lavas. Two-end-member mixing models of Tl with Pb, Sr and Nd isotopes require sediment inputs of< 1%, 0.1-1% and 0.3-2% by weight to the depleted mantle source to account for all these isotopic compositions of lavas from northern, central and southern portion of the Ryukyu arc and Okinawa Trough. Bulk mixing between mantle and sediment end members predict very similar sediment fluxes when using Tl, Sr, Nd and Pb isotopes, which indicates that fractionation of these elements must have happened after mixing between mantle and sediments. This conclusion is corroborated by model calculations of mixing between sediment melts with fractionated Sr/Nd ratios and mantle wedge, which show that no arc lava plot on such mixing lines. Thus bulk sediment mixing, rather than sediment melt, is required for the generation of the lavas from the Ryukyu arc and Okinawa Trough. The requirement of bulk sediment mixing occurring before trace element fractionation in the sub-arc mantle is consistent with models where mélange layers form at the top of the slab and are the principle source material for arc lavas. In addition, the fact that sediment components observed in the Ryukyu arc and Okinawa Trough lavas are similar, suggests that transport of mélange material to the source regions of the arc and back arc is equally efficient. This feature is most readily explained if mélange material is transported from the slab as diapirs.

Buffer layers on metal alloy substrates for superconducting tapes

DOEpatents

Jia, Quanxi; Foltyn, Stephen R.; Arendt, Paul N.; Groves, James R.

2004-06-29

An article including a substrate, a layer of an inert oxide material upon the surface of the substrate, a layer of an amorphous oxide or oxynitride material upon the inert oxide material layer, a layer of an oriented cubic oxide material having a rock-salt-like structure upon the amorphous oxide material layer, and a layer of a SrRuO.sub.3 buffer material upon the oriented cubic oxide material layer is provided together with additional layers such as a HTS top-layer of YBCO directly upon the layer of a SrRuO.sub.3 buffer material layer. With a HTS top-layer of YBCO upon at least one layer of the SrRuO.sub.3 buffer material in such an article, J.sub.c 's of up to 1.3.times.10.sup.6 A/cm.sup.2 have been demonstrated with projected IC's of over 200 Amperes across a sample 1 cm wide.

The evaluation of hydrochemical parameters and lithological characteristics of sediments in some lakes from Danube Delta - Romania Study case: Matita, Babina, Rosu, Uzlina and Isacova Lakes - 2010.

NASA Astrophysics Data System (ADS)

Catianis, I.; Grosu, D.; Radan, S.

2012-04-01

This study attempts to estimate the quality of water and sediments from five lakes of Danube Delta - Romania. Due to the great variety of plant and animal species, delta lakes are considered sensitive ecosystems which may become quite susceptible to anthropogenic influences. The water and sediment samples were gathered from a considerable number of sampling stations during the two campaigns performed in the summer and autumn of 2010. Different techniques were applied to assay variations in surface waters and lacustrine sediment quality. Water samples measured parameters were: dissolved oxygen, temperature, electrical conductivity, total dissolved solids, pH, redox potential, nitrates, nitrites, phosphates, sulphates etc. The main lithological parameters studied were: total organic matter, carbonates and siliciclastic material. The preliminary results indicate that these investigated lakes are quite influenced by external factors as: morphological features, climatic parameters (pressure, humidity, temperature, wind-speed, rainfall etc) and their position within the deltaic hydrological network. Performed analyses showed that the correlations between different parameters differ with respect to sampling station positions. The physico-chemical characteristics of the lakes and connection canals show small variation ranges. In some sampling stations, lower concentration of oxygen and medium pH change from slightly alkaline to alkaline were incidentally observed. The registered data also confirmed the influences of seasonal characteristics. Chemical analyses do not show high values for nitrates, nitrites and sulphates. As regards to phosphate concentration we found out some higher values. In this respect, we have to perform other detailed chemical analyses in order to establish their origin in water. Overall the physico-chemical investigations reveal normal values, which are in agreement with environmental quality standards for surface waters. Sediment cores present uniform profiles, being homogenous in color, varying from light grey brown to dark grey brown, showing sometimes gradual colored particular layers. The water content indicate a general decrease with depth, all cores having a high content of water in the top (fluffy sediments) which decrease downcore, where the sediments become more compact. The bottom sediment samples are quite similar in terms of sedimentology (textural and structural), belonging to the category which range from silty to silty clayey (fine and very fine) and sometimes sandy deposits. Every examined core presents an individual high percentage of organic matter at the top, a subsidiary low content of carbonates and the rest being represented by siliciclastic material. The preliminary assessments performed in 2010 indicate that all five investigated lakes presents a normal environmental status for such water systems with no evident pollution trace. Further detailed chemical analyses are needed to argue the origin and mineralogical composition of organic matter and carbonates which were found out in these reservoirs. Acknowledgments: "This work was supported by the strategic grant POSDRU/89/1.5/S/58852, Project "Postdoctoral program for training scientific researchers" co-financed by the European Social Found within the Sectorial Operational Program Human Resources Development 2007 - 2013", and also was performed with scientific and technical assistance, logistical support and field site access provided by NIRD GeoEcoMar - Romania.

Schottky barrier solar cell

NASA Technical Reports Server (NTRS)

Stirn, R. J.; Yeh, Y. C. M. (Inventor)

1981-01-01

A method of fabricating a Schottky barrier solar cell is described. The cell consists of a thin substrate of low cost material with at least the top surface of the substrate being electrically conductive. A thin layer of heavily doped n-type polycrystalling germanium is deposited on the substrate after a passivation layer is deposited to prevent migration of impurities into the polycrystalline germanium. The polycrystalline germanium is recrystallized to increase the crystal sizes to serve as a base layer on which a thin layer of gallium arsenide is vapor-epitaxilly grown followed by a thermally-grown oxide layer. A metal layer is deposited on the oxide layer and a grid electrode is deposited to be in electrical contact with the top surface of the metal layer.

Quaternary sediment architecture in the Orkhon Valley (central Mongolia) inferred from capacitive coupled resistivity and Georadar measurements

NASA Astrophysics Data System (ADS)

Mackens, Sonja; Klitzsch, Norbert; Grützner, Christoph; Klinger, Riccardo

2017-09-01

Detailed information on shallow sediment distribution in basins is required to achieve solutions for problems in Quaternary geology, geomorphology, neotectonics, (geo)archaeology, and climatology. Usually, detailed information is obtained by studying outcrops and shallow drillings. Unfortunately, such data are often sparsely distributed and thus cannot characterise entire basins in detail. Therefore, they are frequently combined with remote sensing methods to overcome this limitation. Remote sensing can cover entire basins but provides information of the land surface only. Geophysical methods can close the gap between detailed sequences of the shallow sediment inventory from drillings at a few spots and continuous surface information from remote sensing. However, their interpretation in terms of sediment types is often challenging, especially if permafrost conditions complicate their interpretation. Here we present an approach for the joint interpretation of the geophysical methods ground penetrating radar (GPR) and capacitive coupled resistivity (CCR), drill core, and remote sensing data. The methods GPR and CCR were chosen because they allow relatively fast surveying and provide complementary information. We apply the approach to the middle Orkhon Valley in central Mongolia where fluvial, alluvial, and aeolian processes led to complex sediment architecture. The GPR and CCR data, measured on profiles with a total length of about 60 km, indicate the presence of two distinct layers over the complete surveying area: (i) a thawed layer at the surface, and (ii) a frozen layer below. In a first interpretation step, we establish a geophysical classification by considering the geophysical signatures of both layers. We use sedimentological information from core logs to relate the geophysical classes to sediment types. This analysis reveals internal structures of Orkhon River sediments, such as channels and floodplain sediments. We also distinguish alluvial fan deposits and aeolian sediments by their distinct geophysical signature. With this procedure we map aeolian sediments, debris flow sediments, floodplains, and channel sediments along the measured profiles in the entire basin. We show that the joint interpretation of drillings and geophysical profile measurements matches the information from remote sensing data, i.e., the sediment architecture of vast areas can be characterised by combining these techniques. The method presented here proves powerful for characterising large areas with minimal effort and can be applied to similar settings.

Mask fabrication process

DOEpatents

Cardinale, Gregory F.

2000-01-01

A method for fabricating masks and reticles useful for projection lithography systems. An absorber layer is conventionally patterned using a pattern and etch process. Following the step of patterning, the entire surface of the remaining top patterning photoresist layer as well as that portion of an underlying protective photoresist layer where absorber material has been etched away is exposed to UV radiation. The UV-exposed regions of the protective photoresist layer and the top patterning photoresist layer are then removed by solution development, thereby eliminating the need for an oxygen plasma etch and strip and chances for damaging the surface of the substrate or coatings.

Observations of transitional tidal boundary layers and their impact on sediment transport in the Great Bay, NH

NASA Astrophysics Data System (ADS)

Koetje, K. M.; Foster, D. L.; Lippmann, T. C.

2017-12-01

Observations of the vertical structure of tidal flows obtained in 2016 and 2017 in the Great Bay Estuary, NH show evidence of transitional tidal boundary layers at deployment locations on shallow mudflats. High-resolution bottom boundary layer currents, hydrography, turbidity, and bed characteristics were observed with an acoustic Doppler current profiler (ADCP), an acoustic Doppler velocimeter (ADV), conductivity-depth-temperature (CTD) sensors, optical backscatter sensors, multibeam bathymetric surveys, and sediment grab samples and cores. Over the 2.5 m tidal range and at water depths ranging from 0.3 m to 1.5 m at mean lower low water, peak flows ranged from 10 cm/s to 30 cm/s and were primarily driven by the tides. A downward-looking ADCP captured the velocity profile over the lowest 1 m of the water column. Results consistently show a dual-log layer system, with evidence of a lower layer within 15 cm of the bed, another layer above approximately 30 cm from the bed, and a transitional region where the flow field rotates between that the two layers that can be as much as 180 degrees out of phase. CTD casts collected over a complete tidal cycle suggest that the weak thermohaline stratification is not responsible for development of the two layers. On the other hand, acoustic and optical backscatter measurements show spatial and temporal variability in suspended sediments that are dependant on tidal phase. Current work includes an examination of the relationship between sediment concentrations in the water column and velocity profile characteristics, along with an effort to quantify the impact of rotation and dual-log layers on bed stress.

An experimental study of the role of particle diffusive convection on the residence time of volcanic ash clouds

NASA Astrophysics Data System (ADS)

Deal, E.; Carazzo, G.; Jellinek, M.

2013-12-01

The longevity of volcanic ash clouds generated by explosive volcanic plumes is difficult to predict. Diffusive convective instabilities leading to the production of internal layering are known to affect the stability and longevity of these clouds, but the detailed mechanisms controlling particle dynamics and sedimentation are poorly understood. We present results from a series of analog experiments reproducing diffusive convection in a 2D (Hele-Shaw) geometry, which allow us to constrain conditions for layer formation, sedimentation regime and cloud residence time as a function of only the source conditions. We inject a turbulent particle-laden jet sideways into a tank containing a basal layer of salt water and an upper layer of fresh water, which ultimately spreads as a gravity current. After the injection is stopped, particles in suspension settle through the cloud to form particle boundary layers (PBL) at the cloud base. We vary the initial particle concentration of the plume and the injection velocity over a wide range of conditions to identify and characterize distinct regimes of sedimentation. Our experiments show that convective instabilities driven as a result of differing diffusivities of salt and particles lead to periodic layering over a wide range of conditions expected in nature. The flux of particles from layered clouds and the thicknesses of the layers are understood using classical theory for double diffusive convection adjusted for the hydrodynamic diffusion of particles. Although diffusive convection increases sedimentation rates for the smallest particles (<30 μm) its overall effect is to extend the cloud residence time to several hours by maintaining larger particles in suspension within the layers, which is several orders of magnitude longer than expected when considering individual settling rates.

Enhancement of magnetoresistance with low interlayer coupling by insertion of a nano-oxide layer into a free magnetic layer

NASA Astrophysics Data System (ADS)

Nam, Chunghee; Lee, Ki-Su; Cho, B. K.

2005-05-01

We studied the interlayer coupling strength (Hin) and GMR ratio of a spin-valve with the top free layer, separated by a nano-oxide layer (NOL). With the total thickness of the top free layer being fixed at 60Å, the physical properties of the NOL spin-valve were studied with the thickness (tf) of the free layer under the inserted NOL and compared with those of the normal spin-valve with the same thickness as tf. It was found that the spin-valve with NOL has a higher GMR ratio than that of the normal spin-valve at the optimal condition (tf=40Å) after thermal annealing at T =250°C. The NOL spin-valve also shows a lower Hin than that of the optimal normal spin-valve with tf=40Å, which is comparable to that of the normal spin-valve with tf=60Å. This indicates that the enhancement of GMR, while keeping the Hin to be low, can be achieved by inserting a NOL into the top free layer.

Phase-resolved reflectance spectroscopy on layered turbid media

NASA Astrophysics Data System (ADS)

Hielscher, Andreas H.; Liu, Hanli; Chance, Britton; Tittel, Frank K.; Jacques, Steven L.

1995-05-01

In this study, we investigate the influence of layered tissue structures on the phase-resolved reflectance. As a particular example, we consider the affect of the skin, skull, and meninges on noninvasive blood oxygenation determination of the brain. In this case, it's important to know how accurate one can measure the absorption coefficient of the brain through the enclosing layers of different tissues. Experiments were performed on layered gelatin tissue phantoms and the results compared to diffusion theory. It is shown that when a high absorbing medium is placed on top of a low absorbing medium, the absorption coefficient of the lower layer is accessible. In the inverse case, where a low absorbing medium is placed on top of a high absorbing medium, the absorption coefficient of the underlying medium can only be determined if the differences in the absorption coefficient are small, or the top layer is very thin. Investigations on almost absorption and scattering free layers, like the cerebral fluid filled arachnoid, reveal that the determination of the absorption coefficient is barely affected by these kinds of structures.

Multilayer (TiN, TiAlN) ceramic coatings for nuclear fuel cladding

NASA Astrophysics Data System (ADS)

Alat, Ece; Motta, Arthur T.; Comstock, Robert J.; Partezana, Jonna M.; Wolfe, Douglas E.

2016-09-01

In an attempt to develop an accident-tolerant fuel (ATF) that can delay the deleterious consequences of loss-of-coolant-accidents (LOCA), multilayer coatings were deposited onto ZIRLO® coupon substrates by cathodic arc physical vapor deposition (CA-PVD). Coatings were composed of alternating TiN (top) and Ti1-xAlxN (2-layer, 4-layer, 8-layer and 16-layer) layers. The minimum TiN top coating thickness and coating architecture were optimized for good corrosion and oxidation resistance. Corrosion tests were performed in static pure water at 360 °C and 18.7 MPa for up to 90 days. The optimized coatings showed no spallation/delamination and had a maximum of 6 mg/dm2 weight gain, which is 6 times smaller than that of a control sample of uncoated ZIRLO® which showed a weight gain of 40.2 mg/dm2. The optimized architecture features a ∼1 μm TiN top layer to prevent boehmite phase formation during corrosion and a TiN/TiAlN 8-layer architecture which provides the best corrosion performance.

High Temperature Superconducting Thick Films

DOEpatents

Arendt, Paul N.; Foltyn, Stephen R.; Groves, James R.; Holesinger, Terry G.; Jia, Quanxi

2005-08-23

An article including a substrate, a layer of an inert oxide material upon the surface of the substrate, (generally the inert oxide material layer has a smooth surface, i.e., a RMS roughness of less than about 2 nm), a layer of an amorphous oxide or oxynitride material upon the inert oxide material layer, a layer of an oriented cubic oxide material having a rock-salt-like structure upon the amorphous oxide material layer is provided together with additional layers such as at least one layer of a buffer material upon the oriented cubic oxide material layer or a HTS top-layer of YBCO directly upon the oriented cubic oxide material layer. With a HTS top-layer of YBCO upon at least one layer of a buffer material in such an article, Jc's of 1.4×106 A/cm2 have been demonstrated with projected Ic's of 210 Amperes across a sample 1 cm wide.

Ice crystal number concentration measured at mountain-top research stations - What do we measure?

NASA Astrophysics Data System (ADS)

Beck, A.; Henneberger, J.; Fugal, J. P.; David, R.; Larcher, L.; Lohmann, U.

2017-12-01

To assess the impact of surface processes (e.g. blowing snow and hoar frost) on the ice crystal number concentrations (ICNCs) measured at mountain-top research stations, vertical profiles of ICNCs were observed up to a height of 10 m at the Sonnblick Observatory (SBO) in the Hohen Tauern Region, Austria. Independent of the presence of a cloud, the observed ICNCs decrease with height. This suggests a strong impact of surface processes on ICNCs measured at mountain-top research stations. Consequently, the measured ICNCs are not representative of the cloud, which limits the relevance of ground-based measurements for atmospheric studies. When the SBO was cloud free, the observed ICNCs reached several hundreds per liter near the surface and gradually decreased by more than two orders of magnitudes within the observed height interval of 10 m. The observed ice crystals had predominantly irregular habits, which is expected from surface processes. During in-cloud conditions, the ICNCs decreased between a factor of five and ten, if the ICNC at the surface was larger than 100 l-1. For one case study, the ICNC for regular and irregular ice crystals showed a similar relative decrease with height, which is not expected from surface processes. Therefore, we propose two near-surface processes that potentially enrich ICNCs near the surface and explain these findings: Either sedimenting ice crystals are captured in a turbulent layer above the surface or the ICNC is enhanced in a convergence zone, as the cloud is forced over a mountain. These two processes would also have an impact on ICNCs measured at mountain-top stations if the surrounding surface is not snow covered. Thus, ground-based measured ICNCs are uncharacteristic of the cloud properties aloft.

Geophysical Surveys of the Hydrologic Basin Underlying Yosemite Valley, California.

NASA Astrophysics Data System (ADS)

Maher, E. L.; Shaw, K. A.; Carey, C.; Dunn, M. E.; Whitman, S.; Bourdeau, J.; Eckert, E.; Louie, J. N.; Stock, G. M.

2017-12-01

UNR students in an Applied Geophysics course conducted geophysical investigations in Yosemite Valley during the months of March and August 2017. The goal of the study is to understand better the depth to bedrock, the geometry of the bedrock basin, and the properties of stratigraphy- below the valley floor. Gutenberg and others published the only prior geophysical investigation in 1956, to constrain the depth to bedrock. We employed gravity, resistivity, and refraction microtremor(ReMi) methods to investigate the interface between valley fill and bedrock, as well as shallow contrasts. Resistivity and ReMi arrays along three north-south transects investigated the top 50-60m of the basin fill. Gravity results constrained by shallow measurements suggest a maximum depth of 1000 m to bedrock. ReMi and resistivity techniques identified shallow contrasts in shear velocity and electrical resistivity that yielded information about the location of the unconfined water table, the thickness of the soil zone, and spatial variation in shallow sediment composition. The upper several meters of sediment commonly showed shear velocities below 200 m/s, while biomass-rich areas and sandy river banks could be below 150 m/s. Vs30 values consistently increased towards the edge of the basin. The general pattern for resistivity profiles was a zone of relatively high resistivity, >100 ohm-m, in the top 4 meters, followed by one or more layers with decreased resistivity. According to gravity measurements, assuming either -0.5 g/cc or -0.7 g/cc density contrast between bedrock and basin sediments, a maximum depth to bedrock is found south of El Capitan at respectively, 1145 ± 215 m or 818 ± 150 m. Longitudinal basin geometry coincides with the basin depth geometry discussed by Gutenberg in 1956. Their results describe a "double camel" shape where the deepest points are near El Capitan and the Ahwahnee Hotel and is shallowest near Yosemite Falls, in a wider part of the valley. An August Deep ReMi measurement campaign might provide further corroboration between gravity and seismic results for basement depth. This investigation should be useful for refining geologic and hydrologic models, and informing future scientific pursuits in Yosemite Valley.

Dynamic Turbulence Modelling in Large-eddy Simulations of the Cloud-topped Atmospheric Boundary Layer

NASA Technical Reports Server (NTRS)

Kirkpatrick, M. P.; Mansour, N. N.; Ackerman, A. S.; Stevens, D. E.

2003-01-01

The use of large eddy simulation, or LES, to study the atmospheric boundary layer dates back to the early 1970s when Deardor (1972) used a three-dimensional simulation to determine velocity and temperature scales in the convective boundary layer. In 1974 he applied LES to the problem of mixing layer entrainment (Deardor 1974) and in 1980 to the cloud-topped boundary layer (Deardor 1980b). Since that time the LES approach has been applied to atmospheric boundary layer problems by numerous authors. While LES has been shown to be relatively robust for simple cases such as a clear, convective boundary layer (Mason 1989), simulation of the cloud-topped boundary layer has proved more of a challenge. The combination of small length scales and anisotropic turbulence coupled with cloud microphysics and radiation effects places a heavy burden on the turbulence model, especially in the cloud-top region. Consequently, over the past few decades considerable effort has been devoted to developing turbulence models that are better able to parameterize these processes. Much of this work has involved taking parameterizations developed for neutral boundary layers and deriving corrections to account for buoyancy effects associated with the background stratification and local buoyancy sources due to radiative and latent heat transfer within the cloud (see Lilly 1962; Deardor 1980a; Mason 1989; MacVean & Mason 1990, for example). In this paper we hope to contribute to this effort by presenting a number of turbulence models in which the model coefficients are calculated dynamically during the simulation rather than being prescribed a priori.

Ñuagapua (Chaco, Bolivia): Evidence for the latest occurrence of megafauna in association with human remains in South America

NASA Astrophysics Data System (ADS)

Coltorti, Mauro; Della Fazia, Jacopo; Paredes Rios, Freddy; Tito, Giuseppe

2012-02-01

Quebrada (stream) Ñuagapua, which is located in the Bolivian Chaco in the Andean foothill generates an alluvial fan many kilometres in length. Three major lithostratigraphic units characterise the sedimentary sequence in this region. The lower and upper parts are formed from predominantly sandy sediments that demonstrate rapid growth of the alluvial fan, associated with an intense erosion of barren slopes. The intermediate unit consists of forest soil that seals deep channels containing bones together with a forest association. The remains of a wooden plank, dated 140 yr BP, were found at the top of this soil, which laterally contains charcoals, ash layers and large charred trunks, sometimes in growth positions. Roots localised in this layer also sustain a number of very large still living trees. These findings are evidence of a recent phase of alluvial fan sedimentation resulting from slope erosion activated by forest clearing. The Chaco has been intensively settled for agricultural and pastoral purposes since the 18th century. The lower unit contains a hearth, scattered burnt bones, flint flakes and ceramic artefacts. Radiometric dating indicates a middle Holocene human occupation, between ca. 7.79 and 6.65 ka cal yr BP. We suggest that the sedimentary unit is associated with intense soil erosion processes triggered by early Neolithic deforestation. A sandy layer of the lower unit, slightly above the archaeological remains, contains transported bones of megafaunal elements that apparently represent the South American latest occurrence of some extinct taxa. The mammal association is highly heterogeneous, containing species living in aquatic, forest, prairie and savannah environments from a very specific layer that represents the almost simultaneous burial of animals killed slightly up-valley. This anomalous association is probably the result of human impact as opening the forest favoured the introduction of open environment fauna that had previously survived on the southernmost part of the continent. Therefore, humans may have played a role in mammalian extinctions in this region, either directly, due to hunting, or due to changing the paleoenvironmental conditions on a wider scale.

Geochemistry records from laminated sediments of Shira Lake (Russian Asia)

NASA Astrophysics Data System (ADS)

Phedorin, M.; Vologina, E.; Drebuschak, M.; Tolomeev, A.; Kirichenko, I.; Toyabin, A.

2009-04-01

We measured downcore elements distributions in five cores collected across the Shira Lake situated in Central part of Asia (E90o12', N54o30'). The lake is small (32km2), saline (ca.20g/l SO4-, Cl-, Na+, Mg+, K+), being filled with regional precipitation of about 300mm/year (mainly through one major tributary, river Son) and has no surface outflow. The aim of our study was to reconstruct history of changes in the regime of the lake that happened both before and during period of instrumental meteorological observations. In particular, we were interested in lake-level changes due to evaporation, water supply from surface and from underground sources, and in changes of bioproduction in the lake as well. To construct depth-age model for the cores, we measured Cs-137 and unsupported Pb-210 in top layers of the cores. The sedimentation rate thus identified varied in the range of 1-2 mm/year for different cores. We visually observed fine sedimentation ‘rhythms' having thickness of about 0.x-2.x mm: these layers may now be reliably identified as annual lamination. We also determined concentrations of elements in the sediments by recording x-ray fluorescence (XRF) spectra when continuously scanning the halves of the cores under sharp synchrotron radiation (SR) beam, using an instrument described in (Zolotarev et al., 2001). The resolution of the scanning was 0.1 mm. After processing of the measured XRF-SR data as in (Phedorin and Goldberg, 2005) we obtained downcore records of 20 elements. We correlated all five cores employing elements patterns. We qualitatively identified variations in surface-water supply treating markers of ‘clastic' material (Ti, Rb, Zr). We identified downcore variations in authgenic mineralization, which appeared to have different kinds: Ca-related, Sr-related, Ba-related, Fe-related. We tried to assess biogenic production changes from Br distribution, admitting analogy of Br in Shira sediments to Br in Lake Baikal sediments (Phedorin et al., 2000) and in Lake Khubsugul sediments (Phedorin et al., 2008). The cores we studied provide us with high-resolution geochemical records of last century for further meteorological correlations and regressions back to the past. We plan to reconstruct regional trends proceeding with the investigation of this kind and studying sediments of some other Khakas lakes. The investigation was supported by the grant from RFBR (09-05-98027) and grant from the Siberian Branch of Russian Academy of Science. Phedorin M.A., Goldberg E.L., Grachev M.A., Levina O.L., Khlystov O.M., Dolbnya I.P. The Comparison of Biogenic Silica, Br and Nd Distributions in the Sediments of Lake Baikal as Proxies of Changing Paleoclimates of the Last 480 ky. // Nuclear Instruments and Methods in Physics Research, 2000, V. A448, № 1-2, pp. 400-406. Phedorin M.A., Goldberg E.L. Prediction of absolute concentrations of elements from SR XRF scan measurements of natural wet sediments. Nuclear Instruments and Methods in Physics Research A 543 (2005), p. 274-279. Phedorin M.A., Fedotov A.P., Vorobieva S.S., Ziborova G.A.. Signature of long supercycles in the Pleistocene history of Asian limnic systems. J Paleolimnol, 2008, 40/1, pp. 445-452. Zolotarev K.V., Goldberg E.L., Kondratyev V.I., Kulipanov G.N., Miginsky E.G., Tsukanov V.M., Phedorin M.A., Kolmogorov Y.P. Scanning SR-XRF beamline for analysis of bottom sediments. // Nuclear Instruments and Methods in Physics Research, 2001, V. A470, N 1-2, pp. 376-379.

Chembio extraction on a chip by nanoliter droplet ejection.

PubMed

Yu, Hongyu; Kwon, Jae Wan; Kim, Eun Sok

2005-03-01

This paper describes a novel liquid separation technique for chembio extraction by an ultrasonic nanoliter-liquid-droplet ejector built on a PZT sheet. This technique extracts material from an aqueous two-phase system (ATPS) in a precise amount through digital control of the number of nanoliter droplets, without any mixing between the two liquids in the ATPS. The ultrasonic droplet ejector uses an acoustic streaming effect produced by an acoustic beam focused on the liquid surface, and ejects liquid droplets only from the liquid surface without disturbing most of the liquid below the surface. This unique characteristic of the focused acoustic beam is perfect (1) for separating a top-layer liquid (from the bulk of liquid) that contains particles of interest or (2) for recovering a top-layer liquid that has different phase from a bottom-layer liquid. Three kinds of liquid extraction are demonstrated with the ultrasonic droplet ejector: (1) 16 microl of top layer in Dextran-polyethylene glycol-water ATPS (aqueous two-phase system) is recovered within 20 s; (2) micron sized particles that float on water surface are ejected out with water droplets; and (3) oil layer on top of water is separated out.

Research of Houjiayao Unit in North China

NASA Astrophysics Data System (ADS)

Ji, Y.

2012-12-01

"Houjiayao Group" is the standard stratigraphic unit of late Pleistocene in northern China, which was created by Jia Lanpo and Wei Qi during their research on Houjiayao site. Based on the mammal, ancient human fossils and Paleolithic features, "Houjiayao Group" was thought as late Pleistocene sediments. "Houjiayao Group" was defined as late Pleistocene stratigraphic units. However, the problems of the age of "Houjiayao Group", stratigraphic division and other issues, have not yet been well resolved. These issues include: the differences of age-dating results, the unclear comparison between stratigraphic units and regional contrast, the uncertain relationship between "Houjiayao Group" and "Nihewan Layer ", and so on. Houjiayao site which located in the southeast of Houjiayao village in Dongjingji town Yangyuan County, Hebei province of China, is a very important paleolithic site. But some researches show that Houjiayao site is located at the 3th terrace of Liyigou valley and there are many opinions about the age of Houjiayao site, which varies from 20-500 thousand years. Combined with former research results and many research methods, our study was mainly focused on the key problems existing in the study of "Houjiayao Group". Through the use of sequence stratigraphy, chronostratigraphy, biostratigraphy and other theoretical methods, stratigraphic section was studied in the late Pleistocene stratigraphy and sedimentary environment. Through environmental indicators and the age-dating tests, the evolution of ancient geography and environment were identified elementarily. After analyzing informations of this area, geomorphologic investigation and stratum comparation in and around Houjiayao site were done. Houjiayao site is located on the west bank of Liyigou river, which has a tributary named Black Stone River. Two or three layers of volcanic materials were found in this area, those sediments are from a buried paleovolcano in upstream of Black Stone River. The volcanic material layers played an important role in the track of stratum, especially the lower strata. Heights of volcanic sediments become lower south of paleovolcano along the Liyigou River and Black Stone River. The stratum in Houjiayao site shows that the sand-clayey silt-silty clay sediments which are more than 6 meters thick have river sediments characters and they are covered on the culture layers. Culture layers were formed by river and lake. Among the cultural layers, there were two sub-clay layers weak pedogenesis. There is an unconformity sedimentary sequence between the culture layers and the underlying yellow-green lacustrine strata (Nihewan layer). Some volcanic sediments with the K-Ar ages between 0.4-0.5Ma were found in the gray-green Nihewan formation under the culture layers. In general, detailed stratum surveys of this area have not been done before, so this work provided the Lithostratigraphic information for the area research. And with this work, we get the conclusion that Houjiayao site is not located on the 3th terrace of Liyigou valley, and its sediment is one part of Nihewan layers with the age of late Pleistocene.

Effects of gravel on infiltration, runoff, and sediment yield in landslide deposit slope in Wenchuan earthquake area, China.

PubMed

Li, Tianyang; He, Binghui; Chen, Zhanpeng; Zhang, Yi; Liang, Chuan; Wang, Renxin

2016-06-01

Amounts of landslide deposits were triggered by the Wenchuan earthquake with magnitude 8.0 on May 12, 2008. The landslide deposits were composed of soil and rock fragments, which play important roles in hydrological and erosion processes in the steep slope of landslide deposits. The mixtures of soil and gravels are common in the top layers of landslide deposits, and its processes are obviously different with the soil without gravels. Based on the data of field investigation, a series of simulated scouring flow experiments with four proportion of gravel (0, 25, 33.3, and 50 %) and three scouring flow rates (4, 8, 12 L/min) under two steep slopes (67.5, 72.7 %) were conducted sequentially to know the effects of proportion of gravel on infiltration capacity, runoff generation, and sediment production in the steep slope of landslide deposit. Results indicated that gravel had promoted or reduced effects on infiltration capacity which could affect further the cumulative runoff volume and cumulative sediment mass increase or decrease. The cumulative infiltration volume in 25 % proportion of gravel was less than those in 0, 33.3, and 50 % proportion of gravel. The cumulative runoff volume was in an order of 25 > 0 > 33.3 > 50 % while cumulative sediment mass ranked as 25 > 33.3 > 0 > 50 % with different proportions of gravel. A significant power relationship was found between scouring time and cumulative runoff volume as well as cumulative sediment mass. The relationship between average soil and water loss rate and proportion of gravel was able to express by quadratic function, with a high degree of reliability. The results have important implications for soil and water conservation and modeling in landslide deposit but also provide useful information for the similar conditions.

Sediment sound velocities from Sonobuoys: Sunda Trench and forearc basins, Nicobar and Central Bengal Fans, and Andaman Sea Basins

NASA Astrophysics Data System (ADS)

Bachman, Richard T.; Hamilton, Edwin L.; Curray, Joseph R.

1983-11-01

Supplement is available with entire article on microfiche. Order from American Geophysical Union, 2000 Florida Avenue, N.W., Washington, DC 20009. Document B83-007; $2.50. Payment must accompany order. Measurements of mean sound velocities in the first, largely unlithified layers in the seafloor were made using the sonobuoy technique in several areas in the northern Indian Ocean. Older measurements were added to new measurements, and regressions for mean and instantaneous velocity versus one-way travel time of sound are presented for the central Bengal Fan, the central Andaman Sea Basin, the Nicobar Fan, and the Sunda Trench. New data and regression equations are presented for the Mergui-north Sumatra Basin and for four forearc basins between Sumatra and Java and the Sunda Trench. Minimum velocity gradients were found in those areas where sedimentation rates were high, and sediments have accumulated in thick sections which have not had time to fully consolidate (porosity in the top of the sediment section has not been fully reduced under overburden pressure). These minimum velocity gradients (just under the seafloor) were found in the four forearc basins where they ranged from 0.34 s-1 to 0.84 s-1 with an average of 0.58 s-1. The near-surface velocity gradient in the Sunda Trench was 1.33 s-1, but was higher in the adjacent, fossil Nicobar Fan (1.62 s-1). In the surface of the Bengal Fan the velocity gradient was low in the upper fan (0.86 s-1), high in the central fan (1.94 s-1), and again lower in the southern fan (1.18 s-1), which may support sedimentation models calling for bypassing of the central fan and higher rates of accumulation on the southern fan.

Particulate export and lateral advection in the Antarctic Polar Front (Southern Pacific Ocean): One-year mooring deployment

NASA Astrophysics Data System (ADS)

Tesi, T.; Langone, L.; Ravaioli., M.; Giglio, F.; Capotondi, L.

2012-12-01

An instrumented mooring line with sediment traps, current meters and recorders of temperature and conductivity was deployed just south of the Antarctic Polar Front (63° 26‧ S, 178° 03‧E; water depth 4400 m) from January 9th 1999 to January 10th 2000. Sediment traps at 900 and 3700 m had a single large cup to collect particulate material throughout the 1-year study whereas time-series sediment traps were used to characterize the temporal variability at 1300 and 2400 m. Samples were characterized via several parameters including total mass flux, elemental composition (organic carbon, total nitrogen, biogenic silica, and calcium carbonate), concentration of metals (aluminum, iron, barium, and manganese), 210Pb activity, and foraminifera identification. High vertical fluxes of biogenic particles were observed in both summer 1999 and 2000 as a result of seasonal algal blooms associated with sea ice retreat and water column stratification. During autumn and winter, several high energy events occurred and resulted in advecting resuspended biogenic particles from flat-topped summits of the Pacific Antarctic Ridge. Whereas the distance between seabed and uppermost sediment traps was sufficient to avoid lateral advection processes, resuspension was significant in the lowermost sediment traps accounting for ~ 60 and ~ 90% of the material caught at 2400 and 3700 m, respectively. Although resuspended material showed an elemental composition relatively similar to vertical summer fluxes, samples collected during high energy events contained benthic foraminifera and exhibited significantly higher 210Pb activity indicating a longer residence time in the water column. In addition, during quiescent periods characterized by low mass fluxes, the content of lithogenic particles increased at the expense of phytodetritus indicating the influence of material advected through the benthic nepheloid layer. Organic matter content was particularly high during these periods and showed statistically significant linear correlations with metals suggesting adsorption of organic coatings onto the mineral surface of lithogenic particles.

A FIRE-ACE/SHEBA Case Study of Mixed-Phase Arctic Boundary Layer Clouds: Entrainment Rate Limitations on Rapid Primary Ice Nucleation Processes

NASA Technical Reports Server (NTRS)

Fridlin, Ann; vanDiedenhoven, Bastiaan; Ackerman, Andrew S.; Avramov, Alexander; Mrowiec, Agnieszka; Morrison, Hugh; Zuidema, Paquita; Shupe, Matthew D.

2012-01-01

Observations of long-lived mixed-phase Arctic boundary layer clouds on 7 May 1998 during the First International Satellite Cloud Climatology Project (ISCCP) Regional Experiment (FIRE)Arctic Cloud Experiment (ACE)Surface Heat Budget of the Arctic Ocean (SHEBA) campaign provide a unique opportunity to test understanding of cloud ice formation. Under the microphysically simple conditions observed (apparently negligible ice aggregation, sublimation, and multiplication), the only expected source of new ice crystals is activation of heterogeneous ice nuclei (IN) and the only sink is sedimentation. Large-eddy simulations with size-resolved microphysics are initialized with IN number concentration N(sub IN) measured above cloud top, but details of IN activation behavior are unknown. If activated rapidly (in deposition, condensation, or immersion modes), as commonly assumed, IN are depleted from the well-mixed boundary layer within minutes. Quasi-equilibrium ice number concentration N(sub i) is then limited to a small fraction of overlying N(sub IN) that is determined by the cloud-top entrainment rate w(sub e) divided by the number-weighted ice fall speed at the surface v(sub f). Because w(sub c)< 1 cm/s and v(sub f)> 10 cm/s, N(sub i)/N(sub IN)<< 1. Such conditions may be common for this cloud type, which has implications for modeling IN diagnostically, interpreting measurements, and quantifying sensitivity to increasing N(sub IN) (when w(sub e)/v(sub f)< 1, entrainment rate limitations serve to buffer cloud system response). To reproduce observed ice crystal size distributions and cloud radar reflectivities with rapidly consumed IN in this case, the measured above-cloud N(sub IN) must be multiplied by approximately 30. However, results are sensitive to assumed ice crystal properties not constrained by measurements. In addition, simulations do not reproduce the pronounced mesoscale heterogeneity in radar reflectivity that is observed.

Transport mechanisms of contaminants released from fine sediment in rivers

NASA Astrophysics Data System (ADS)

Cheng, Pengda; Zhu, Hongwei; Zhong, Baochang; Wang, Daozeng

2015-12-01

Contaminants released from sediment into rivers are one of the main problems to study in environmental hydrodynamics. For contaminants released into the overlying water under different hydrodynamic conditions, the mechanical mechanisms involved can be roughly divided into convective diffusion, molecular diffusion, and adsorption/desorption. Because of the obvious environmental influence of fine sediment (D_{90}= 0.06 mm), non-cohesive fine sediment, and cohesive fine sediment are researched in this paper, and phosphorus is chosen for a typical adsorption of a contaminant. Through theoretical analysis of the contaminant release process, according to different hydraulic conditions, the contaminant release coupling mathematical model can be established by the N-S equation, the Darcy equation, the solute transport equation, and the adsorption/desorption equation. Then, the experiments are completed in an open water flume. The simulation results and experimental results show that convective diffusion dominates the contaminant release both in non-cohesive and cohesive fine sediment after their suspension, and that they contribute more than 90 % of the total release. Molecular diffusion and desorption have more of a contribution for contaminant release from unsuspended sediment. In unsuspension sediment, convective diffusion is about 10-50 times larger than molecular diffusion during the initial stages under high velocity; it is close to molecular diffusion in the later stages. Convective diffusion is about 6 times larger than molecular diffusion during the initial stages under low velocity, it is about a quarter of molecular diffusion in later stages, and has a similar level with desorption/adsorption. In unsuspended sediment, a seepage boundary layer exists below the water-sediment interface, and various release mechanisms in that layer mostly dominate the contaminant release process. In non-cohesive fine sediment, the depth of that layer increases linearly with shear stress. In cohesive fine sediment, the range seepage boundary is different from that in non-cohesive sediment, and that phenomenon is more obvious under a lower shear stress.

In situ measurement of radioactive contamination of bottom sediments.

PubMed

Zhukouski, A; Anshakou, O; Kutsen, S

2018-04-30

A gamma spectrometric method is presented for in situ radiation monitoring of bottom sediments with contaminated layer of unknown thickness to be determined. The method, based on the processing of experimental spectra using the results of their simulation by the Monte Carlo method, is proposed and tested in practice. A model for the transport of gamma radiation from deposited radionuclides 137 Cs and 134 Cs to a scintillation detection unit located on the upper surface of the contaminated layer of sediments is considered. The relationship between the effective radius of the contaminated site and the thickness of the layer has been studied. The thickness of the contaminated layer is determined by special analysis of experimental and thickness-dependent simulated spectra. The technique and algorithm developed are verified as a result of full-scale studies performed with the submersible gamma-spectrometer. Copyright © 2018 Elsevier Ltd. All rights reserved.

Field monitoring of toxic organic pollution in the sediments of Pearl River estuary and its tributaries.

PubMed

Fu, J; Wang, Z; Mai, B; Kang, Y

2001-01-01

Field monitoring of the toxic organic compounds (PCBs, PAHs, organochlorine pesticides) in the top sediments of Pearl River Estuary and its up-streams were made. It was found that the highest concentrations of these toxic organic compounds occurred in the sediment sampled at Macau inner harbor (ZB013), which is a sink of suspended fine particles transported from the upstream waterways. Because of the affinity of the hydrophobic organic compounds (PAHs, PCBs) for the solid phase, these fine particle depositions led to accumulation of these compounds in the sediment of Macau. The atmospheric dry deposition may be another source of the toxic organic pollution in the sediment.

Dynamics of a cliff top dune

NASA Astrophysics Data System (ADS)

Rasmussen, K. R.

2012-12-01

Morphological changes during more than 100 years have been investigated for a cliff-top dune complex at Rubjerg at the Danish North Sea coast. Here the lower 50 m of the cliff front is composed of Pleistocene steeply inclined floes of silt and clay with coarse sand in between which gives it a saw-tooth appearance. On top of this the dunes are found for several kilometres along the coastline. Due to erosion by the North Sea the cliff has retreated about 120 m between approximately 1880 and 1970 as indicated from two national surveys, and recent GPS-surveys indicate that erosion is continuing at a similar rate. Nevertheless the cliff top dune complex has survived, but its morphology has undergone some changed. The old maps indicate that around 1880 the dune complex was composed of several up to about 20 m high dunes streamlined in the East-West direction which is parallel to the prevailing wind direction. When protective planting started during the first half of the 20th Century the cliff top dunes gradually merged together forming a narrow, tall ridge parallel to the shore line with the highest part reaching about 90 m near 1970. In 1993 the highest points along the ridge was almost 95 m high, but then the protective planting was considerably reduced and recent annual GPS-surveys indicate that the dunes respond quickly to this by changing their morphology towards the original appearance. It is remarkable that despite the mass wasting caused by the constant erosion of the cliff front the dunes have remained more or less intact. Theoretical studies of hill flow indicate given the proper geometry of the cliff then suspension of even coarse grains can be a very effective agent for carrying sand from the exposed parts of the cliff front to and beyond the cliff-top. Mostly the sand grains are deposited within some hundred meters downwind of the cliff dune while silt is often carried more than 10 km inland. Field observations indicate that where the dislodged floes and beds of coarse sand are missing the cliff is steep and dunes are absent at the cliff top. On the other hand when floes are present then some parts of the cliff are less steep and where sand is abundant cliff top dunes seem to be abundant, too. In order to investigate how flow conditions at the cliff front responds to its geometry, scale models of the cliff front approximately 1:10, but with different steepness have been tested in a boundary layer wind tunnel. All runs have been made with proper roughness scaling and besides a variation in their longitudinal profiles some variation in their transverse profiles has also been tested. The surface-near flow has been mapped with high resolution 2-D laser-Doppler profiling, and one of the important aims is to demonstrate the interaction between sediment and geological structure on one side and flow and dune state on the other side. A particular aim is to investigate if and how the separation bubble may have a profound control on mobilization and transport of sediment.

Buffer layers on metal alloy substrates for superconducting tapes

DOEpatents

Jia, Quanxi; Foltyn, Stephen R.; Arendt, Paul N.; Groves, James R.

2004-10-05

An article including a substrate, at least one intermediate layer upon the surface of the substrate, a layer of an oriented cubic oxide material having a rock-salt-like structure upon the at least one intermediate layer, and a layer of a SrRuO.sub.3 buffer material upon the oriented cubic oxide material layer is provided together with additional layers such as a HTS top-layer of YBCO directly upon the layer of a SrRuO.sub.3 buffer material layer. With a HTS top-layer of YBCO upon at least one layer of the SrRuO.sub.3 buffer material in such an article, J.sub.c 's of up to 1.3.times.10.sup.6 A/cm.sup.2 have been demonstrated with projected I.sub.c 's of over 200 Amperes across a sample 1 cm wide.

Structural deformation and sedimentation in an active Caldera, Rabaul, Papua New Guinea

USGS Publications Warehouse

Greene, H. Gary; Tiffin, D.L.; McKee, C.O.

1986-01-01

Recent seismic and tectonic activity in Rabaul Caldera, Papua New Guinea, suggests that magma is accumulating at a shallow depth beneath this partially submerged structure and that a new volcano may be developing. Changes in onshore elevation since 1971 (as much as 2 m on south Matupit Island) indicate that rapid and large-scale uplifts have occurred on the seafloor near the center of the caldera. The frequency of seismic events within the caldera has also increased during this period. Earthquake locations define an elliptical ring surrounding the center of this uplift within the caldera. A marine geophysical survey in 1982 by the U.S. Geological Survey's R/V "S.P. Lee" in Rabaul Caldera shows the development of a bulge in the seafloor near the center of the caldera. High-resolution seismic reflection profiles show that this bulge consists of two domal uplifts bounded and separated by two major north-south-trending fault zones. Deformed sediments overlie these zones; a prominent slump flanks the area of the bulge. Five major acoustic units were identified in the seismic reflection profiles: an acoustic basement and four sedimentary units consisting of irregularly layered, cross-layered, contorted, and well-layered sequences. The acoustic basement is probably composed of crystalline volcanic rocks, and the layered acoustic units are probably sediments, primarily ash deposited in different environments. The cross-layered, irregularly layered, and contorted units appear to have been deposited in a dynamic environment subjected to strong currents, seismicity, and/or mass wasting, while the well-layered units were deposited in a low-energy environment. Locally, well-layered sequences interfinger with the other sedimentary units, indicating a transitional environment that alternated between high-energy and low-energy depositional processes. A submarine channel cuts most of the acoustic units and appears to be the conduit for sediment transport out of the caldera; it occupies an older buried channel north of the caldera that is presently being exhumed. In the south, active erosion of well-layered sediments is taking place. What are believed to be several young volcanic cones also disrupt the depositional layers. We conclude that the bulge in the seafloor and the associated fault zones are a result of emplacement of magma at a shallow depth. Contorted sediment and slumps adjacent to the bulge are probably the result of uplift and seismic activity. The pattern of seismicity appears to reflect increased magma pressure at depth beneath the caldera floor. This activity may eventually lead to an eruption. ?? 1986.

Dynamics of the Sediment Plume Over the Yangtze Bank in the Yellow and East China Seas

NASA Astrophysics Data System (ADS)

Luo, Zhifa; Zhu, Jianrong; Wu, Hui; Li, Xiangyu

2017-12-01

A distinct sediment plume exists over the Yangtze Bank in the Yellow and East China Seas (YECS) in winter, but it disappears in summer. Based on satellite color images, there are two controversial viewpoints about the formation mechanism for the sediment plume. One viewpoint is that the sediment plume forms because of cross-shelf sediment advection of highly turbid water along the Jiangsu coast. The other viewpoint is that the formation is caused by local bottom sediment resuspension and diffused to the surface layer through vertical turbulent mixing. The dynamic mechanism of the sediment plume formation has been unclear until now. This issue was explored by using a numerical sediment model in the present paper. Observed wave, current, and sediment data from 29 December 2016 to 16 January 2017 were collected near the Jiangsu coast and used to validate the model. The results indicated that the model can reproduce the hydrodynamic and sediment processes. Numerical experiments showed that the bottom sediment could be suspended by the bottom shear stress and diffuse to the surface layer by vertical mixing in winter; however, the upward diffusion is restricted by the strong stratification in summer. The sediment plume is generated locally due to bottom sediment resuspension primarily via tide-induced bottom shear stress rather than by cross-shelf sediment advection over the Yangtze Bank.

Long range wetting transparency on top of layered metal dielectric substrates

DTIC Science & Technology

2015-11-20

multi-layered stacks were deposited onto glass substrates ( silica -based Micro cover glass , 22mmx22mm from VWR (48366-067), index of refraction n...necessarily endorsed by the United States Government. Long-range wetting transparency on top of layered metal-dielectric substrates M. A...as far as ~100 nm beneath the water/MgF2 interface. We refer to this phenomenon as long range wetting transparency . The latter effect cannot be

Modeling interface roughness scattering in a layered seabed for normal-incident chirp sonar signals.

PubMed

Tang, Dajun; Hefner, Brian T

2012-04-01

Downward looking sonar, such as the chirp sonar, is widely used as a sediment survey tool in shallow water environments. Inversion of geo-acoustic parameters from such sonar data precedes the availability of forward models. An exact numerical model is developed to initiate the simulation of the acoustic field produced by such a sonar in the presence of multiple rough interfaces. The sediment layers are assumed to be fluid layers with non-intercepting rough interfaces.

Influence of silver nanoparticles on benthic oxygen consumption of microbial communities in freshwater sediments determined by microelectrodes.

PubMed

Miao, Lingzhan; Wang, Chao; Hou, Jun; Wang, Peifang; Ao, Yanhui; Li, Yi; Yao, Yu; Lv, Bowen; Yang, Yangyang; You, Guoxiang; Xu, Yi

2017-05-01

The increased use of silver nanoparticles (AgNPs) will inevitably result in the release of these particles into aquatic environments, with sediments as a substantial sink. However, we do not know whether AgNPs present potential impacts in sediment functioning. In this study, a microcosm approach was constructed, and the potential impacts of AgNPs and PVP-coated AgNPs on oxygen consumption in freshwater sediments (collected from Taihu Lake) were determined using oxygen microelectrodes. To our knowledge, this is the first time that microelectrodes have been used to estimate the impacts of AgNPs in sediments. The steady-state oxygen microprofiles showed that environmental relevant concentration (1 mg/L nano-Ag) did not lead to an apparent change in the oxygen consumption rates of benthic microbial communities in sediment. The addition of 10 mg/L uncoated AgNPs resulted in remarkable differences in the oxygen concentration profiles within 4-5 h and significantly inhibited the oxygen consumption of benthic microbial communities in the upper sediment layer (∼1 mm) after 100 h. Simultaneously, an increase of oxygen consumption in sediment lower zones was observed. These results may suggest that aerobic microorganisms in the upper layer of the sediment reduced metabolic activity to avoid the toxic stress from AgNPs. Concomitantly, facultative aerobes below the metabolically active upper layer switched from fermentation or anaerobic respiration to aerobic respiration as oxygen bioavailability increased in the lower zones of the sediment. In addition, PVP coating reduced the nanotoxicity of AgNPs in benthic microorganisms due to the decreased dissolution of AgNPs in the filtered overlying water, a phenomenon that merits further investigation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Layered Outcrops of Far West Candor Chasma

NASA Technical Reports Server (NTRS)

2000-01-01

[figure removed for brevity, see original site]

Images from Mariner 9 in 1972 revealed that some of the mesas and mounds found within the chasms of the martian 'Grand Canyon'--the Valles Marineris--have layers in them. Speculations as to the origin of these interior layered materials ranged from volcanic ash deposits to sediments laid down in lakes that could have partially filled the Vallis Marineris troughs, much as lakes now occupy portions of the rift valleys of eastern Africa. The proposal that the Valles Marineris once hosted deep martian lakes led to additional speculation as to the prospects for finding fossil evidence of martian life.

Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) images have ten or more times better resolution than the Mariner 9 and Viking orbiter images taken in the 1970s. MOC images have indeed confirmed the presence of layered outcrops within the Valles Marineris. They have also shown places previously not suspected to have layered rock, and they have shown that these materials might not have formed in the Valles Marineris, but were instead deposited in craters that were subsequently buried long before the chasms opened up (see discussion below). The layered rock is now visible because of faulting and erosion.

The high resolution picture shown here (B, above right) was the first image received by MOC scientists that began to hint at a larger story of layered sedimentary rock on Mars. The picture shows a 1.5 km by 2.9 km (0.9 mi by 1.8 mi) area in far southwestern Candor Chasma (A, above left) that was--based on Mariner 9 and Viking orbiter images--not previously expected to exhibit layers. The MOC image reveals that the floor of western Candor Chasma at this location is indeed layered. What is most striking about the picture is the large number and uniformity of the layers, or beds. There are over 100 beds in this area, and each has about the same thickness (estimated to be about 10 meters (11 yards) thick). Each layer has a relatively smooth upper surface, and each is hard enough to form steep cliffs at its margins.

Layers indicate change. The uniform pattern seen here--beds of similar properties and thickness repeated over a hundred times--suggest that the deposition of materials that made the layers was interrupted at regular or episodic intervals. Patterns like this, when found on Earth, usually indicate the presence of sediment deposited in dynamic, energetic, underwater environments. On Mars, these same patterns could very well indicate that the materials were deposited in a lake or shallow sea. Other MOC images suggest that these layers would not have formed in a lake in Candor Chasma, but instead were deposited in a crater or other basin that existed before Candor Chasma was cut (by faulting and erosion) into the surrounding terrain. However, it is not known for certain that these materials actually formed underwater, for it is possible that there were uniquely Martian processes occurring in the distant past that would mimic the pattern of sedimentation in water. For example, if the early Martian atmosphere was denser than it is today, and if the planet's atmospheric pressure changed on a cyclic basis (as it does today), then perhaps these materials are simply deposits of airborne dust that were later buried and cemented to create cliff-forming rock.

Sunlight illuminates both the wide angle context view and the narrow angle high resolution image from the left/upper left. In both, north is toward the top and east to the right.

Interplay between dewetting and layer inversion in poly(4-vinylpyridine)/polystyrene bilayers.

PubMed

Thickett, Stuart C; Harris, Andrew; Neto, Chiara

2010-10-19

We investigated the morphology and dynamics of the dewetting of metastable poly(4-vinylpyridine) (P4VP) thin films situated on top of polystyrene (PS) thin films as a function of the molecular weight and thickness of both films. We focused on the competition between the dewetting process, occurring as a result of unfavorable intermolecular interactions at the P4VP/PS interface, and layer inversion due to the lower surface energy of PS. By means of optical and atomic force microscopy (AFM), we observed how both the dynamics of the instability and the morphology of the emerging patterns depend on the ratio of the molecular weights of the polymer films. When the bottom PS layer was less viscous than the top P4VP layer (liquid-liquid dewetting), nucleated holes in the P4VP film typically stopped growing at long annealing times because of a combination of viscous dissipation in the bottom layer and partial layer inversion. Full layer inversion was achieved when the viscosity of the top P4VP layer was significantly greater (>10⁴) than the viscosity of the PS layer underneath, which is attributed to strongly different mobilities of the two layers. The density of holes produced by nucleation dewetting was observed for the first time to depend on the thickness of the top film as well as the polymer molecular weight. The final (completely dewetted) morphology of isolated droplets could be achieved only if the time frame of layer inversion was significantly slower than that of dewetting, which was characteristic of high-viscosity PS underlayers that allowed dewetting to fall into a liquid-solid regime. Assuming a simple reptation model for layer inversion occurring at the dewetting front, the observed surface morphologies could be predicted on the basis of the relative rates of dewetting and layer inversion.

Identity and abundance of active sulfate-reducing bacteria in deep tidal flat sediments determined by directed cultivation and CARD-FISH analysis.

PubMed

Gittel, Antje; Mussmann, Marc; Sass, Henrik; Cypionka, Heribert; Könneke, Martin

2008-10-01

The identity and abundance of potentially active sulfate-reducing bacteria (SRB) in several metre deep sediments of a tidal sand flat in the German Wadden Sea were assessed by directed cultivation and cultivation-independent CARD-FISH analysis (catalysed reporter deposition fluorescence in situ hybridization). Presumably abundant SRB from different sediment layers between 0.5 and 4 m depth were selectively enriched in up to million-fold diluted cultures supplemented with lactate, acetate or hydrogen. Partial 16S rRNA gene sequences obtained from highest dilution steps showing sulfide formation indicated growth of deltaproteobacterial SRB belonging to the Desulfobulbaceae and the Desulfobacteraceae as well as of members of the Firmicutes. Subsequent isolation resulted in 10 novel phylotypes of both litho- and organotrophic sulfate-reducing Deltaproteobacteria. Molecular pre-screening identified six isolates as members of the Desulfobulbaceae, sharing highest identities with either candidatus 'Desulfobacterium corrodens' (95-97%) or Desulfobacterium catecholicum (98%), and four isolates as members of Desulfobacteraceae, being related to either Desulfobacter psychrotolerans (98%) or Desulfobacula phenolica (95-97%). Relatives of D. phenolica were exlusively isolated from 50 and 100 cm deep sediments with 10 and 2 mM of pore water sulfate respectively. In contrast, relatives of D. corrodens, D. psychrotolerans and D. catecholicum were also obtained from layers deeper than 100 cm and with less than 2 mM sulfate. The high in situ abundance of members of both families in sediment layers beneath 50 cm could be confirmed via CARD-FISH analysis performed with a set of six SRB-specific oligonucleotide probes. Moreover, SRB represented a numerically significant fraction of the microbial community throughout the sediment (up to 7%) and reached even higher cell numbers in deep, sulfate-poor layers than in the sulfate-rich surface sediment. This relatively large community size of potentially active SRB in deep sandy sediments might on the one hand be a result of their syntrophic association with other anaerobes. Our results furthermore support the hypothesis that enhanced advective pore water transport might supply nutrients to microbial communities in deep sandy sediments and point to their so far unrecognized contribution to biogeochemical processes in Wadden Sea sediments.

Plasmon resonance imaging apparatus having nano-lycurgus-cup arrays and methods of use

DOEpatents

Liu, Gang Logan; Gartia, Manas Ranjan; Hsiao, Austin Yin Kyai

2016-10-11

Apparatus and methods are disclosed that are configured to permit nanoplasmonic spectroscopy sensing in the form of colorimetric sensing. An example apparatus involves: (a) an array layer having a top surface and a bottom surface, wherein a plurality of nanoholes are defined in the top surface of the array layer, wherein the plurality of nanoholes each have at least one sidewall surface and a bottom surface, (b) a thin metal film disposed on the top surface of the array layer and on the bottom surface of each of the plurality of nanoholes, and (c) a plurality of nanoparticles disposed on the at least one sidewall surface of the plurality of nanoholes.

Trace Metals and Lead Isotopes in modern Sediments Near Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Boyle, E. A.; Lazzari, L.; Wagener, A. L.; Carreira, R.; Godoy, J. M.; Noble, A.; Carrasco, G. G.; Moos, S. B.

2014-12-01

This work focuses on the export of trace metals and combustion residues from land to ocean and on the Southeast continental margin of Brazil and its historical variability using stable lead isotopes. Two sediment cores were collected, one in highly impacted Guanabara Bay and the other on the Southeast continental shelf. Continental shelf samples were analyzed for trace element concentrations [Mn (117±50 ppm), Ni (6.5±2.3 ppm), Zn (5.0±1.5), (233±46 ppm), ], Pb (5.4±2.4 ppm), as well as Cu, Ag, Cd, Sr, Ba, Tl, U and Pb isotope ratios & Pb-210. Most of the elements show higher concentrations on the upper part of the core compared to the bottom. Downcore changes of the concentrations of these elements were similar. The sediments of adjacent rivers and bays around the upper section of the southeast continental shelf of Brazil are considered highly enriched with Pb, Zn, Cu and Cr such as Guanabara Bay, Sepetiba Bay and Paraíba do Sul River compared with the natural concentrations and other regions in the world. A [Pb] maximum is seen between samples from 24 to 43 cm (~8 ppm). Utilization of tetraethyl lead (TEL) gasoline in Brazil was phased out beginning in 1983 and was largely completed by 1988. Continental shelf Pb-206/Pb-207 varies between 1.174 near the core top to 1.190 at 100 cm, with a sharp difference between samples at 6 and 8 cm. Higher core top Pb, Zn, and Ni corroborate the recent anthropogenic influence on the southeast continental shelf of Brazil. For Guanabara Bay sediment samples [Pb] varies between 90 ppm near the top to 1 ppm at the bottom. Pb-206/Pb-207 varies between 1.161 near the core top to 1.165 near the bottom. Using triple isotope plots we can discern different sources of lead to the region and how these vary with time.

[Pollution and Potential Ecology Risk Evaluation of Heavy Metals in River Water, Top Sediments on Bed and Soils Along Banks of Bortala River, Northwest China].

PubMed

Zhang, Zhao-yong; Abuduwaili, Jilili; Jiang, Feng-qing

2015-07-01

This paper focuses on the sources, pollution status and potential ecology risks of heavy metals (Cr, Cu, Hg, As, Cd, Pb, and Zn) in the surface water, top sediment of river bed and soil along banks of Bortala River, which locates in the oasis region of Xinjiang, northwest China. Results showed that: (1) As a whole, contents of 7 tested heavy metals of Bortala River were low, while the maximum values of Hg, Cd, Pb, and Cr in the river water were significantly higher than those of Secondary Category of the Surface Water Quality Standards of People's Republic of China (GB 3838-2002) and Drinking Water Guideline from WHO. Analysis showed that the heavy metals contents of top sediment on river bed and soils along river banks were significantly higher than those of the river water. (Correlation analysis and enrichment factor (EF) calculation showed that in the river water, top sediment on river bed and soils along river banks, Hg, Cd, Pb, and Cr mainly originated from industrial emissions, urban and rural anthropogenic activities, transportation and agricultural production activities; While Cu, Zn, and As mainly originated from natural geological background and soil parent materials. (3) Pollution assessment showed that in three matrices, the single factor pollution index(Pi) and the integrated pollution index (Pz) of 7 heavy metals were all lower than 1, and they all belonged to safe and clean levels. (4) Potential ecology risk evaluation showed that as a whole the single factor potential ecological risk (Eir) and the integrated potential ecology risks (RI) of 7 heavy metals were relatively low, and would not cause threats to the health of water and soil environment of river basin, while the potential ecology risks of Cd, Hg, Pb, and Cr were significantly higher than those of other heavy metals.

Neodymium isotopes in authigenic phases, bottom waters and detrital sediments in the Gulf of Alaska and their implications for paleo-circulation reconstruction

NASA Astrophysics Data System (ADS)

Du, Jianghui; Haley, Brian A.; Mix, Alan C.

2016-11-01

The isotopic composition of neodymium (εNd) extracted from sedimentary Fe-Mn oxyhydroxide offers potential for reconstructing paleo-circulation, but its application depends on extraction methodology and the mechanisms that relate authigenic εNd to bottom water. Here we test methods to extract authigenic εNd from Gulf of Alaska (GOA) sediments and assess sources of leachate Nd, including potential contamination from trace dispersed volcanic ash. We show that one dominant phase is extracted via leaching of core-top sediments. Major and trace element geochemistry demonstrate that this phase is authigenic Fe-Mn oxyhydroxide. Contamination of leachate (authigenic) Nd from detrital sources is insignificant (<1%); our empirical results are consistent with established kinetic mineral dissolution rates and theory. Contamination of extracted εNd from leaching of volcanic ash is below analytical uncertainty. However, the εNd of core-top leachates in the GOA is consistently more radiogenic than bottom water. We infer that authigenic phases record pore water εNd, and the relationships of εNd among bottom waters, pore waters, authigenic phases and detrital sediments are primarily governed by the exposure time of bottom water to sea-floor sediments, rate of exchange across the sediment-water interface and the reactivity and composition of detrital sediments. We show that this conceptual model is applicable on the Pacific basin scale and provide a new framework to understand the role of authigenic phases in both modern and paleo-applications, including the use of authigenic εNd as a paleo-circulation tracer.

Bioturbation by the Fungus-Gardening Ant, Trachymyrmex septentrionalis

PubMed Central

Tschinkel, Walter R.; Seal, Jon N.

2016-01-01

Soil invertebrates such as ants are thought to be important manipulators of soils in temperate and tropical ecosystems. The fungus gardening ant, Trachymyrmex septentrionalis, is an important agent of biomantling, that is, of depositing soil excavated from below onto the surface, and has been suggested as an agent of bioturbation (moving soil below ground) as well. The amount of bioturbation by this ant was quantified by planting queenright colonies in sand columns consisting of 5 layers of different colored sand. The amount of each color of sand deposited on the surface was determined from April to November 2015. In November, colonies were excavated and the color and amount of sand deposited below ground (mostly as backfill in chambers) was determined. Extrapolated to one ha, T. septentrionalis deposited 800 kg of sand per annum on the surface, and an additional 200 kg (17% of the total excavated) below ground. On average, this mixes 1.3% of the sand from other layers within the top meter of soil per millennium, but this mixing is unlikely to be homogeneous, and probably occurs as "hotspots" in both horizontal and vertical space. Such mixing is discussed as a challenge to sediment dating by optically stimulated luminescence (OSL). PMID:27391485

Bioturbation by the Fungus-Gardening Ant, Trachymyrmex septentrionalis.

PubMed

Tschinkel, Walter R; Seal, Jon N

2016-01-01

Soil invertebrates such as ants are thought to be important manipulators of soils in temperate and tropical ecosystems. The fungus gardening ant, Trachymyrmex septentrionalis, is an important agent of biomantling, that is, of depositing soil excavated from below onto the surface, and has been suggested as an agent of bioturbation (moving soil below ground) as well. The amount of bioturbation by this ant was quantified by planting queenright colonies in sand columns consisting of 5 layers of different colored sand. The amount of each color of sand deposited on the surface was determined from April to November 2015. In November, colonies were excavated and the color and amount of sand deposited below ground (mostly as backfill in chambers) was determined. Extrapolated to one ha, T. septentrionalis deposited 800 kg of sand per annum on the surface, and an additional 200 kg (17% of the total excavated) below ground. On average, this mixes 1.3% of the sand from other layers within the top meter of soil per millennium, but this mixing is unlikely to be homogeneous, and probably occurs as "hotspots" in both horizontal and vertical space. Such mixing is discussed as a challenge to sediment dating by optically stimulated luminescence (OSL).

Long-term recovery of PCB-contaminated surface sediments at the Sangamo-westonl Twelvemile Creek/lake Hartwell Superfund Site.

PubMed

Brenner, Richard C; Magar, Victor S; Ickes, Jennifer A; Foote, Eric A; Abbott, James E; Bingler, Linda S; Crecelius, Eric A

2004-04-15

Natural recovery of contaminated sediments relies on burial of contaminated sediments with increasingly clean sediments over time (i.e., natural capping). Natural capping reduces the risk of resuspension of contaminated surface sediments, and it reduces the potential for contaminant transport into the food chain by limiting bioturbation of contaminated surface or near-surface sediments. This study evaluated the natural recovery of surface sediments contaminated with polychlorinated biphenyls (PCBs) at the Sangamo-Weston/Twelvemile Creek/Lake Hartwell Superfund Site (Lake Hartwell), Pickens County, SC. The primary focus was on sediment recovery resulting from natural capping processes. Total PCB (t-PCB), lead-210 (210Pb), and cesium-137 (137Cs) sediment core profiles were used to establish vertical t-PCB concentration profiles, age date sediments, and determine surface sedimentation and surface sediment recovery rates in 18 cores collected along 10 transects. Four upgradient transects in the headwaters of Lake Hartwell were impacted by historical sediment releases from three upgradient sediment impoundments. These transects were characterized by silt/ clay and sand layering. The highest PCB concentrations were associated with silt/clay layers (1.8-3.5% total organic carbon (TOC)), while sand layers (0.05-0.32% TOC) contained much lower PCB concentrations. The historical sediment releases resulted in substantial burial of PCB-contaminated sediment in the vicinity of these four cores; each core contained less than 1 mg/kg t-PCBs in the surface sand layers. Cores collected from six downgradient Lake Hartwell transects consisted primarily of silt and clay (0.91-5.1% TOC) and were less noticeably impacted by the release of sand from the impoundments. Vertical t-PCB concentration profiles in these cores began with relatively low PCB concentrations at the sediment-water interface and increased in concentration with depth until maximum PCB concentrations were measured at approximately 30-60 cm below the sediment-water interface, ca. 1960-1980. Maximum t-PCB concentrations were followed by progressively decreasing concentrations with depth until the t-PCB concentrations approached the detection limit, where sediments were likely deposited before the onset of PCB use at the Sangamo-Weston plant. The sediments containing the maximum PCB concentrations are associated with the period of maximum PCB release into the watershed. Sedimentation rates averaged 2.1 +/- 1.5 g/(cm2 yr) for 12 of 18 cores collected. The 1994 Record of Decision cleanup requirement is 1.0 mg/kg; two more goals (0.4 and 0.05 mg/kg t-PCBs) also were identified. Average surface sedimentation requirements to meet the three goals were 1.4 +/- 3.7, 11 +/- 4.2, and 33 +/- 11 cm, respectively. Using the age dating results, the average recovery dates to meet these goals were 2000.6 +/- 2.7, 2007.4 +/- 3.5, and 2022.7 +/- 11 yr, respectively. (The 95% prediction limits for these values also are provided.) Despite the reduction in surface sediment PCB concentrations, PCB concentrations measured in largemouth bass and hybrid bass filets continue to exceed the 2.0 mg/kg FDA fish tolerance level.

Estimation of Nutrients Flux of Water-sediment Interface in the Chukchi Sea, the Western Arctic Ocean

NASA Astrophysics Data System (ADS)

Zhang, H.

2016-02-01

Nutrients regeneration in pore water is one of the important ways to supply nutrients of upper water column in the shelf. The pore water in sediment of the central Chukchi Sea continental shelf, showed a typical benthic distribution of nutrients at water-sediment interface, in where physical and bioturbation was weak. The nutrient samples in multi-tubular short column sediment and water column were obtained from the Forth Chinese National Arctic Research Expedition, to measure the nutrient concentrations of pore water, overlying water and water column. The results show that, the typical distribution can be separated into three layers. The first layer is the exponential increasing layer (I), in which the concentrations of nutrients increased rapidly with depth. Then was the steady layer (II), the sediment demineralization was equal to the nutrient transference and nutrients' concentrations were substantially constant at this stage. The third layer was a slowly descending layer (III), in which NO3- and PO43- were reduced by bacteria and lost oxygen ions due to organic materials degradation depleting oxygen. By a two-layer mode and the Fick's first law of diffusion, diffusive fluxes of silicate, phosphate and nitrate in R06 station of the Chukchi Sea shelf can be calculated, and the fluxes were 1.660 mmol/(m2 · d), 0.008 mmol/(m2 · d) and 0.117 mmol/(m2 · d), respectively. The diffusive fluxes of silicate for CC1, R06, C07 and S23 stations were 3.101 mmol/(m2 · d), 1.660 mmol/(m2 · d), 1.307 mmol/(m2 · d) and mmol/(m2 · d), respectively, which show obvious distribution characteristics with latitude. Distribution of N * in the pore water suggested that a strong denitrification process in sedimentary environment of the Chukchi Sea shelf, which is an important sink for nitrate.

Mechanical stratification of autochthonous salt: Implications from basin-scale numerical models of rifted margin salt tectonics

NASA Astrophysics Data System (ADS)

Ings, Steven; Albertz, Markus

2014-05-01

Deformation of salt and sediments owing to the flow of weak evaporites is a common phenomenon in sedimentary basins worldwide, and the resulting structures and thermal regimes have a significant impact on hydrocarbon exploration. Evaporite sequences ('salt') of significant thickness (e.g., >1km) are typically deposited in many cycles of seawater inundation and evaporation in restricted basins resulting in layered autochthonous evaporite packages. However, analogue and numerical models of salt tectonics typically treat salt as a homogeneous viscous material, often with properties of halite, the weakest evaporite. In this study, we present results of two-dimensional plane-strain numerical experiments designed to illustrate the effects of variable evaporite viscosity and embedded frictional-plastic ('brittle') sediment layers on the style of salt flow and associated deformation of the sedimentary overburden. Evaporite viscosity is a first-order control on salt flow rate and the style of overburden deformation. Near-complete evacuation of low-viscosity salt occurs beneath expulsion basins, whereas significant salt is trapped when viscosity is high. Embedded frictional-plastic sediment layers (with finite yield strength) partition salt flow and develop transient contractional structures (folds, thrust faults, and folded faults) in a seaward salt-squeeze flow regime. Multiple internal sediment layers reduce the overall seaward salt flow during sediment aggradation, leaving more salt behind to be re-mobilized during subsequent progradation. This produces more seaward extensive allochthonous salt sheets. If there is a density difference between the embedded layers and the surrounding salt, then the embedded layers 'fractionate' during deformation and either float to the surface or sink to the bottom (depending on density), creating a thick zone of pure halite. Such a process of 'buoyancy fractionation' may partially explain the apparent paradox of layered salt in autochthonous salt basins and thick packages of pure halite in allochthonous salt sheets.

Distribution of hydrothermal fluid around the ore body in the subseafloor of the Izena hydrothermal field

NASA Astrophysics Data System (ADS)

Toki, T.; Otake, T.; Ishibashi, J. I.; Matsui, Y.; Kawagucci, S.; Kato, H.; Fuchida, S.; Miyahara, R.; Tsutsumi, A.; Kawakita, R.; Uza, H.; Uehara, R.; Shinjo, R.; Nozaki, T.; Kumagai, H.; Maeda, L.

2017-12-01

From 16th November to 15th December 2016, D/V Chikyu drilled the sea bottom around hydrothermal fields at HAKUREI site in the Izena Hole, Okinawa Trough. Site C9025, C9026, C9027, C9028, and C9032 are located along the transect line from the top of the northern mound of HAKUREI site to the eastward, and Site C9030 for the control site is located about 500 m northwest of the mound. Mg concentrations have generally been used to estimate mixing ratios between hydrothermal end-member and seawater in samples from hydrothermal vents. Higher Mg concentrations, however, were detected in the interstitial water than that of seawater, which could be due to artificially dissolution of Mg-bearing minerals that had formed in in-situ environments, when the cored sediments had become cool after their recovery on ship. Similar features were observed with regard to sulfate concentrations, and it suggests that these chemical species are not suitable to estimate quantitatively the contribution of hydrothermally-derived components. In some layers, chloride concentrations were different from that of seawater, indicating that hydrothermal fluids that had been suffered from phase separation flowed into the layers. The deviation, however, was positive or negative relative to that of seawater for an influence of brine or vapor phase, respectively. Therefore chloride concentrations are also not suitable to evaluate a quantitative contribution of hydrothermal end-member. On the other hand, K and B showed only enrichments relative to the seawater, and their highest concentrations are consistent with the reported hydrothermal end-members of each species at HAKUREI site. Using the concentrations of K and B can be evaluated for an influence of hydrothermal components. Furthermore, the headspace gas data are useful in the layers of sulfide minerals and silicified rocks, even though the interstitial waters could not be obtained because of their hardness. Based on these indices, hydrothermal fluids would be distributed in the upper and lower layers of the ore body. The hydrothermally altered sediment layers above the ore body contain relatively unstable minerals that dissociate immediately in a room temperature, which could play a role as a boundary between hydrothermal fluids and intruded seawater in in-situ environments.

A Combined Field and Laboratory Study on Activated Carbon-Based Thin Layer Capping in a PCB-Contaminated Boreal Lake.

PubMed

Abel, Sebastian; Akkanen, Jarkko

2018-04-17

The in situ remediation of aquatic sediments with activated carbon (AC)-based thin layer capping is a promising alternative to traditional methods, such as sediment dredging. Applying a strong sorbent like AC directly to the sediment can greatly reduce the bioavailability of organic pollutants. To evaluate the method under realistic field conditions, a 300 m 2 plot in the PCB-contaminated Lake Kernaalanjärvi, Finland, was amended with an AC cap (1.6 kgAC/m 2 ). The study lake showed highly dynamic sediment movements over the monitoring period of 14 months. This led to poor retention and rapid burial of the AC cap under a layer of contaminated sediment from adjacent sites. As a result, the measured impact of the AC amendment was low: Both the benthic community structure and PCB bioaccumulation were similar on the plot and in surrounding reference sites. Corresponding follow-up laboratory studies using Lumbriculus variegatus and Chironomus riparius showed that long-term remediation success is possible, even when an AC cap is covered with contaminated sediment. To retain a measurable effectiveness (reduction in contaminant bioaccumulation), a sufficient intensity and depth of bioturbation is required. On the other hand, the magnitude of the adverse effect induced by AC correlated positively with the measured remediation success.

Unexpectedly higher metazoan meiofauna abundances in the Kuril-Kamchatka Trench compared to the adjacent abyssal plains

NASA Astrophysics Data System (ADS)

Schmidt, Christina; Martínez Arbizu, Pedro

2015-01-01

We studied meiofauna standing stocks and community structure in the Kuril-Kamchatka Trench and its adjacent abyssal plains in the northwestern Pacific Ocean. In general, the Nematoda were dominant (93%) followed by the Copepoda (4%). Nematode abundances ranged from 87% to 96%; those of copepods from 2% to 7%. The most diverse deployment yielded 17 taxa: Acari, Amphipoda, Annelida, Bivalvia, Coelenterata, Copepoda, Cumacea, Gastrotricha, Isopoda, Kinorhyncha, Loricifera, Nematoda, Ostracoda, Priapulida, Tanaidacea, Tantulocarida, and Tardigrada. Nauplii were also present. Generally, the trench slope and the southernmost deployments had the highest abundances (850-1392 individuals/cm2). The results of non-metric multidimensional scaling indicated that these deployments were similar to each other in meiofauna community structure. The southernmost deployments were located in a zone of higher particulate organic carbon (POC) flux (g Corg m-2 yr-1), whereas the trench slope should have low POC flux due to depth attenuation. Also, POC and abundance were significantly correlated in the abyssal plains. This correlation may explain the higher abundances at the southernmost deployments. Lateral transport was also assumed to explain high meiofauna abundances on the trench slope. Abundances were generally higher than expected from model results. ANOSIM revealed significant differences between the trench slope and the northern abyssal plains, between the central abyssal plains and the trench slope, between the trench slope and the southern abyssal plains, between the central and the southern abyssal plains, and between the central and northern deployments. The northern and southern abyssal plains did not differ significantly. In addition, a U-test revealed highly significant differences between the trench-slope and abyssal deployments. The taxa inhabited mostly the upper 0-3 cm of the sediment layer (Nematoda 80-90%; Copepoda 88-100%). The trench-slope and abyssal did not differ in occupancy of the top layer. Furthermore, sediment depth and abundance were strongly correlated, but the sediment texture itself and the grain sizes showed only slight correlations with abundance. In the trench slope no correlation between sediment texture and abundance was found. We suggest that sediment is not the only factor that affects meiofauna abundance in the study area. The results of our study were compared with other trench and nontrench studies, and in most cases, the abundance decreases with depth initially but increases again below a certain depth, especially in deep-sea trenches below productive waters. No generalization can be made, however, about the depth at which the reversal occurs; it depends on the area of investigation and on a mixture of many other factors (e.g., sediment heterogeneity, oxygen, redox potential, proximity to land masses, and season).

Effects of Different Materials Used for Internal Floating Electrode on the Photovoltaic Properties of Tandem Type Organic Solar Cell

NASA Astrophysics Data System (ADS)

Triyana, Kuwat; Yasuda, Takeshi; Fujita, Katsuhiko; Tsutsui, Tetsuo

2004-04-01

Three thin heterojunctions sandwiched between indium tin oxide (ITO) and the top electrode as triple-heterojunction organic solar cells have been fabricated. Each heterojunction cell consists of CuPc as a donor layer and perilene tetracrboxylic-bis-benzimidazole (PTCBI) as an acceptor layer. Ultra thin (1 nm average thickness) layers of Ag or Au have been inserted between two heterojunctions as an internal electrode. Ag and Au were chosen as materials both for internal floating and top electrodes. Influences of different deposition sequences of the organic layer in each heterojunction cell and different electrode materials were also investigated. The optimum devices were obtained when the same material was used both as an internal electrode and a top electrode. When the deposition sequence of the heterojunction is PTCBI/CuPc, the most suitable electrode is Au and the ITO is negative relative to the top electrode. Meanwhile, Ag is suitable for an electrode when the deposition sequence is CuPc/PTCBI. In this second deposition sequence, the ITO is positive relative to the top electrode. The open circuit voltage (Voc) of both optimum devices is on the order of 1.35-1.5 V. These values are approximately three times higher than that in single-heterojunction organic solar cells.

A modified gradient approach for the growth of low-density InAs quantum dot molecules by molecular beam epitaxy

NASA Astrophysics Data System (ADS)

Sharma, Nandlal; Reuter, Dirk

2017-11-01

Two vertically stacked quantum dots that are electronically coupled, so called quantum dot molecules, are of great interest for the realization of solid state building blocks for quantum communication networks. We present a modified gradient approach to realize InAs quantum dot molecules with a low areal density so that single quantum dot molecules can be optically addressed. The individual quantum dot layers were prepared by solid source molecular beam epitaxy depositing InAs on GaAs(100). The bottom quantum dot layer has been grown without substrate rotation resulting in an In-gradient across the surface, which translated into a density gradient with low quantum dot density in a certain region of the wafer. For the top quantum dot layer, separated from the bottom quantum dot layer by a 6 nm thick GaAs barrier, various InAs amounts were deposited without an In-gradient. In spite of the absence of an In-gradient, a pronounced density gradient is observed for the top quantum dots. Even for an In-amount slightly below the critical thickness for a single dot layer, a density gradient in the top quantum dot layer, which seems to reproduce the density gradient in the bottom layer, is observed. For more or less In, respectively, deviations from this behavior occur. We suggest that the obvious influence of the bottom quantum dot layer on the growth of the top quantum dots is due to the strain field induced by the buried dots.

An Unusual Inverted Saline Microbial Mat Community in an Interdune Sabkha in the Rub' Alkhali (the Empty Quarter), UAE: an Analog for Habitats on Present Mars

NASA Technical Reports Server (NTRS)

McKay, Christopher P.; Rask, Jon C.; Detweiler, Angela M.; Bebout, Brad M.; Everroad, R. Craig; Chanton, Jeffrey P.; Mayer, Marisa H.; Caraballo, Adrian A. L.; Kapili, Bennett

2016-01-01

Salt flats (sabkha) are a recognized habitat for microbial life in desert environments and as analogs for habitats for life on Mars. Here we report on the physical setting and microbiology of interdune sabkhas among the large dunes in the Rub' al Khali (the Empty Quarter) in Liwa Oasis, United Arab Emirates. The salt flats, composed of gypsum and halite, between the dunes are moistened by relatively fresh ground water from below. The result is a salinity gradient that is inverted compared to most salt flat communities with the hypersaline layer at the top and freshwater layers below. We describe and characterize a rich photosynthetically-based microbial ecosystem that is protected from the arid outside environment below the translucent salt crust. Gases collected from sediments under shallow ponds in the sabkha contain methane in concentrations as high as 3400 ppm. The salt layer provides environmental protection to the habitat below and could preserve biomarkers and other evidence for life in the salt after it dries out. Chloride-filled depressions have been identified on Mars and although the surface flow of water is unlikely on Mars today, ground water is possible. Such a near surface system with modern groundwater flowing under ancient salt deposits could be present on Mars and could be accessed by surface rovers.

The frequency-domain approach for apparent density mapping

NASA Astrophysics Data System (ADS)

Tong, T.; Guo, L.

2017-12-01

Apparent density mapping is a technique to estimate density distribution in the subsurface layer from the observed gravity data. It has been widely applied for geologic mapping, tectonic study and mineral exploration for decades. Apparent density mapping usually models the density layer as a collection of vertical, juxtaposed prisms in both horizontal directions, whose top and bottom surfaces are assumed to be horizontal or variable-depth, and then inverts or deconvolves the gravity anomalies to determine the density of each prism. Conventionally, the frequency-domain approach, which assumes that both top and bottom surfaces of the layer are horizontal, is usually utilized for fast density mapping. However, such assumption is not always valid in the real world, since either the top surface or the bottom surface may be variable-depth. Here, we presented a frequency-domain approach for apparent density mapping, which permits both the top and bottom surfaces of the layer to be variable-depth. We first derived the formula for forward calculation of gravity anomalies caused by the density layer, whose top and bottom surfaces are variable-depth, and the formula for inversion of gravity anomalies for the density distribution. Then we proposed the procedure for density mapping based on both the formulas of inversion and forward calculation. We tested the approach on the synthetic data, which verified its effectiveness. We also tested the approach on the real Bouguer gravity anomalies data from the central South China. The top surface was assumed to be flat and was on the sea level, and the bottom surface was considered as the Moho surface. The result presented the crustal density distribution, which was coinciding well with the basic tectonic features in the study area.

Extreme Events on a Low-Gradient River and Delta: Evidence for Sediment Mass Movements on the Subaqueous Delta and a Mechanism for Creating Hyperpycnal Flow onto the Shelf

NASA Astrophysics Data System (ADS)

Dellapenna, T. M.; Carlin, J. A.; Williams, J. R.

2016-02-01

The Brazos River empties into the Gulf of Mexico (GOM) forming a wave-influenced, muddy, subaqueous delta (SAD). Recent research in the estuarine reach of the river and on the SAD, however, found evidence for significant mass wasting of the delta-front and potential evidence of hyperpycnal flow, a processes typically associated with higher gradient and higher sediment yield rivers. The study used high-resolution geophysics on the SAD and water-column profiling in the lower river to investigate the transfer to and fate of fluvial sediment on the shelf. The SAD side scan mosaic combined with core data reveal that the eastern portion was dominated by exposed relict, consolidated sediment; an erosional scarp along the upper shoreface; and a thinning of the Holocene strata immediately downslope of the scarp. Holocene strata thickness increases into deeper water. These features suggest sediment mass wasting on the delta front. After rapidly prograding during the early and mid 20th century, reductions in sediment load due anthropogenic influences, and a shift in the primary depocenter lead to erosion on these abandoned portions of the delta. During an elevated fluvial discharge event, a >1 m thick fluid mud layer was found along a 6 km span of the river 2 km upstream from the mouth. The river's salt wedge was shown to inhibit sediment export from the river to the GOM, and facilitate deposition of mud in the lower river. We believe that the mud layer in the lower river builds during moderate and low discharge periods and remobilized during increased discharge, potentially resulting in hyperpyncnal flow to the shelf. We observed suspended sediment concentrations up to 100 g/l in the fluid mud layer during this event. While our observations did not capture the transition from fluid mud to hyperpycnal flow, we believe that with persistent increased discharge the fluid mud layer could transition to hyperpycnal flow.

Electron trapping in the photo-induced conductivity decay in GaAs/SnO2 heterostructure

NASA Astrophysics Data System (ADS)

de Freitas Bueno, Cristina; de Andrade Scalvi, Luis Vicente

2018-06-01

The decay of photo-induced conductivity is measured for GaAs/SnO2 heterostructure, after illumination with appropriate wavelength. The top oxide layer is deposited by sol-gel-dip-coating and doped with Eu3+, and the GaAs bottom layer is deposited by resistive evaporation. It shows quite unusual behavior since the decay rate gets slower as the temperature is raised. The trapping by intrabandgap defects in the SnO2 top layer is expected, but a GaAs/SnO2 interface arrest becomes also evident, mainly for temperatures below 100 K. Concerning the SnO2 layer, trapping by different defects is possible, due to the observed distinct capture time range. Besides Eu3+ centers and oxygen vacancies, this sort of heterostructure also leads to Eu3+ agglomerate areas in the SnO2 top layer surface, which may contribute for electron scattering. The electrical behavior reported here aims to contribute for the understanding of the electrical transport mechanisms which, combined with emission from Eu3+ ions from the top layer of the heterostructure, opens new possibilities for optoelectronic devices because samples in the form of films are desirable for circuit integration. The modeling of the photo-induced decay data yields the capture barrier in the range 620-660 meV, and contributes for the defect rules on the electrical properties of this heterostructure.

Long-term performance and bacterial community dynamics in biocovers for mitigating methane and malodorous gases.

PubMed

Lee, Eun-Hee; Moon, Kyung-Eun; Cho, Kyung-Suk

2017-01-20

The long-term performance of lab-scale biocovers for the simulation of engineered landfill cover soils was evaluated. Methane (CH 4 ), trimethylamine (TMA), and dimethyl sulfide (DMS) were introduced into the biocovers as landfill gases for 134 days and the removal performance was evaluated. The biocover systems were capable of simultaneously removing methane, TMA, and DMS. Methane was mostly eliminated in the top layer of the systems, while TMA and DMS were removed in the bottom layer. Overall, the methane removal capacity and efficiency were 224.8±55.6g-CH 4 m -2 d -1 and 66.6±12.8%, respectively, whereas 100% removal efficiencies of both TMA and DMS were achieved. Using quantitative PCR and pyrosequencing assay, the bacterial and methanotrophic communities in the top and bottom layers were analyzed along with the removal performance of landfill gases in the biocovers. The top and bottom soil layers possessed distinct communities from the original inoculum, but their structure dynamics were different from each other. While the structures of the bacterial and methanotrophic communities showed little change in the top layer, both communities in the bottom layer were considerably shifted by adding TMA and DMA. These findings provide information that can extend the understanding of full-scale biocover performance in landfills. Copyright © 2016 Elsevier B.V. All rights reserved.

Particulate export vs lateral advection in the Antarctic Polar Front (Southern Pacific Ocean)

NASA Astrophysics Data System (ADS)

Tesi, T.; Langone, L.; Ravaioli, M.; Capotondi, L.; Giglio, F.

2012-04-01

The overarching goal of our study was to describe and quantify the influence of lateral advection relative to the vertical export in the Antarctic Polar Front (Southern Pacific Ocean). In areas where lateral advection of particulate material is significant, budgets of bioactive elements can be inaccurate if fluxes through the water column and to the seabed are exclusively interpreted as passive sinking of particles. However, detailed information on the influence of lateral advection in the water column in the southern ocean is lacking. With this in mind, our study focused between the twilight zone (i.e. mesopelagic) and the benthic nepheloid layer to understand the relative importance of lateral flux with increasing water depth. Measurements were performed south of the Antarctic Polar Front for 1 year (January 10th 1999-January 3rd 2000) at 900, 1300, 2400, and 3700 m from the sea surface. The study was carried out using a 3.5 km long mooring line instrumented with sediment traps, current meters and sensors of temperature and conductivity. Sediment trap samples were characterized via several parameters including total mass flux, elemental composition (organic carbon, total nitrogen, biogenic silica, and calcium carbonate), concentration of metals (aluminum, iron, barium, and manganese), 210Pb activity, and foraminifera taxonomy. High fluxes of biogenic particles were observed in both summer 1999 and 2000 as a result of seasonal algal blooms associated with sea ice retreat and water column stratification. During no-productive periods, several high energy events occurred and resulted in advecting resuspended biogenic particles from flat-topped summits of the Pacific Antarctic Ridge. Whereas the distance between seabed and uppermost sediment traps was sufficient to avoid lateral advection processes, resuspension was significant in the lowermost sediment traps accounting for ~60 and ~90% of the material caught at 2400 and 3700 m, respectively. Samples collected during high energy events contained benthic foraminifera and exhibited significantly higher 210Pb activity indicating a longer residence time in the water column. In addition, during winter quiescent periods characterized by low mass fluxes, the content of lithogenic particles increased at the expenses of phytodetritus suggesting the presence of lateral advection of fine particles permanently in suspension within the benthic nepheloid layer. In spite of the low mass flux, organic matter content was particularly high during these periods accounting for almost 10% of the global pool of organic matter.

Distribution and bioavailability of cadmium in ornithogenic coral-sand sediments of the Xisha archipelago, South China Sea.

PubMed

Liu, Xiaodong; Lou, Chuangneng; Xu, Liqiang; Sun, Liguang

2012-09-01

Total cadmium (Cd) concentrations in four ornithogenic coral-sand sedimentary profiles displayed a strong positive correlation with guano-derived phosphorus, but had no correlation with plant-originated organic matter in the top sediments. These results indicate that the total Cd distributions were predominantly controlled by guano input. Bioavailable Cd and zinc (Zn) had a greater input rate in the top sediments with respect to total Cd and total Zn, and a positive correlation with total organic carbon (TOC) derived from plant humus. Multi-regression analysis showed that the total Cd and TOC explained over 80% of the variation of bioavailable Cd, suggesting that both guano and plant inputs could significantly influence the distribution of bioavailable Cd, and that plant biocycling processes contribute more to the recent increase of bioavailable Cd. A pollution assessment indicates that the Yongle archipelago is moderately to strongly polluted with guano-derived Cd. Copyright © 2012 Elsevier Ltd. All rights reserved.

A bilayer model for bedload sediment transport as generalization of Exner models

NASA Astrophysics Data System (ADS)

Escalante, Cipriano; Fernandez-Nieto, Enrique; Morales de Luna, Tomas; Narbona Reina, Gladys

2017-04-01

Sediment can be transported in several ways by the action of a river. During low transport stages, particles move by sliding and rolling over the surface of the bed. This type of transport is usually called bedload transport. The usual approach to model these phenomena is to use the Saint-Venant-Exner model (SVE) which consists in a shallow water model coupled with a morphodynamical component for the bedload transport. The bedload transport depends on an empirical flux. Nevertheless, this approach presents some drawbacks, for instance, gravitational effects for bedload transport is neglected and the momentum equation for the sediment is missing. In this work we present a two-layer shallow water type model in order to better describe bedload transport. We consider an upper layer consisting in clear water and a lower layer which accounts for the sediment material. This allows to better describe the phenomena. The key point is the definition of the friction laws between the two layers. The model is a generalization of classic models as it allows to recover SVE system when the ratio between the hydrodynamic and morphodynamic time scales is small, as commonly done to derive SVE models.

Oceanographic controls over sediment water content: northern Bermuda rise

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, M.; Laine, E.P.

1985-01-01

Cores taken from the plateaus of Northern Bermuda Rise show that the region is underlain at depths of 1-5 m by a 1-3 m thick layer of hemipelagic lutites with anomalously high water contents. The lack of visually apparent textural and lithological changes in this extremely fine grained sediment rule out these common causes for variation in water content. The water content averages 175% within this layer and 100% immediately above and below it. This is an increase of 9.5% in porosity. The high water content sediment is confined to a period between 12 and 16 ka. Current work onmore » the mineralogy of the sediments which comprise this layer suggest two oceanographic factors that may have influenced its formation. A meltwater spike associated with deglaciation may have altered the ecological conditions above the thermocline sufficiently to promote the increased production of radiolaria, resulting in the deposition of silica enriched sediment on the sea floor. A combination of textural and perhaps chemical factors caused by the silica enrichment may have influenced the increase in water content. Intensified bottom currents at this time also may have eroded smectite rich sediments from exposures of Neogene age and deposited them on the plateaus. An increase in smectite would increase the water content due to the extremely fine grain size and the chemistry of the clay. Thus, the lateral continuity and isochroniety of this layer, combined with its mineralogical characteristics suggests that oceanographic changes can influence water content and perhaps other geotechnical properties on a regional scale.« less

Spectral ellipsometry as a method for characterization of nanosized films with ferromagnetic layers

NASA Astrophysics Data System (ADS)

Hashim, H.; Singkh, S. P.; Panina, L. V.; Pudonin, F. A.; Sherstnev, I. A.; Podgornaya, S. V.; Shpetnyi, I. A.; Beklemisheva, A. V.

2017-11-01

Nanosized films with ferromagnetic layers are widely used in nanoelectronics, sensor systems and telecommunications. Their properties may strongly differ from those of bulk materials that is on account of interfaces, intermediate layers and diffusion. In the present work, spectral ellipsometry and magnetooptical methods are adapted for characterization of the optical parameters and magnetization processes in two- and three-layer Cr/NiFe, Al/NiFe and Cr(Al)/Ge/NiFe films onto a sitall substrate for various thicknesses of Cr and Al layers. At a layer thickness below 20 nm, the complex refractive coefficients depend pronouncedly on the thickness. In two-layer films, remagnetization changes weakly over a thickness of the top layer, but the coercive force in three-layer films increases by more than twice upon remagnetization, while increasing the top layer thickness from 4 to 20 nm.

Observations of marine decoupled boundary layer during the ICOS campaign at the GAW Mace Head station, Ireland.

NASA Astrophysics Data System (ADS)

Milroy, Conor; Martucci, Giovanni; O'Dowd, Colin

2010-05-01

The planetary boundary layer (PBL) top height detections have been retrieved by two ceilometers (Vaisala CL31 and Jenoptik CHM15K) and a microwave radiometer (RPG-HATPRO) based at the Mace Head Research station, Ireland, from the 8th to the 28th of June 2009 during the ICOS Mace Head campaign. Characteristic of this region, with warm waters, the marine boundary layer is typically 2-layered with a surface mixed layer (SML) and a decoupled residual or convective layer (DRCL), above which is the free troposphere (Kunz et al. 2002). The PBL data have been analyzed using a newly developed Temporal Height-Tracking (THT) algorithm (Martucci et al., 2010) for automatic detection of the independent SML and DRCL tops. Daily and weekly averages of the PBL data have been performed to smooth out the short term variability and assess the dependence of the PBL depth on different air masses advected over the Mace Head station. Moreover, a qualitative comparison between the ceilometer and radiometer PBL top detected values has been done to assess their consistency.

Formation of anomalous eutectic in Ni-Sn alloy by laser cladding

NASA Astrophysics Data System (ADS)

Wang, Zhitai; Lin, Xin; Cao, Yongqing; Liu, Fencheng; Huang, Weidong

2018-02-01

Ni-Sn anomalous eutectic is obtained by single track laser cladding with the scanning velocity from 1 mm/s to 10 mm/s using the Ni-32.5 wt.%Sn eutectic powders. The microstructure of the cladding layer and the grain orientations of anomalous eutectic were investigated. It is found that the microstructure is transformed from primary α-Ni dendrites and the interdendritic (α-Ni + Ni3Sn) eutectic at the bottom of the cladding layer to α-Ni and β-Ni3Sn anomalous eutectic at the top of the cladding layer, whether for single layer or multilayer laser cladding. The EBSD maps and pole figures indicate that the spatially structure of α-Ni phase is discontinuous and the Ni3Sn phase is continuous in anomalous eutectic. The transformation from epitaxial growth columnar at bottom of cladding layer to free nucleation equiaxed at the top occurs, i.e., the columnar to equiaxed transition (CET) at the top of cladding layer during laser cladding processing leads to the generation of anomalous eutectic.

Doubled heterogeneous crystal nucleation in sediments of hard sphere binary-mass mixtures

NASA Astrophysics Data System (ADS)

Löwen, Hartmut; Allahyarov, Elshad

2011-10-01

Crystallization during the sedimentation process of a binary colloidal hard spheres mixture is explored by Brownian dynamics computer simulations. The two species are different in buoyant mass but have the same interaction diameter. Starting from a completely mixed system in a finite container, gravity is suddenly turned on, and the crystallization process in the sample is monitored. If the Peclet numbers of the two species are both not too large, crystalline layers are formed at the bottom of the cell. The composition of lighter particles in the sedimented crystal is non-monotonic in the altitude: it is first increasing, then decreasing, and then increasing again. If one Peclet number is large and the other is small, we observe the occurrence of a doubled heterogeneous crystal nucleation process. First, crystalline layers are formed at the bottom container wall which are separated from an amorphous sediment. At the amorphous-fluid interface, a secondary crystal nucleation of layers is identified. This doubled heterogeneous nucleation can be verified in real-space experiments on colloidal mixtures.

Assessing the continuity of the upland sediment cascade, fluvial geomorphic response of an upland river to an extreme flood event: Storm Desmond, Cumbria, UK.

NASA Astrophysics Data System (ADS)

Joyce, Hannah; Hardy, Richard; Warburton, Jeff

2017-04-01

Hillslope erosion and accelerated lake sedimentation are often viewed as the source and main storage elements in the upland sediment cascade. However, the continuity of sediment transfer through intervening valley systems has rarely been evaluated during extreme events. Storm Desmond (4th - 6th December, 2015) produced record-breaking rainfall maximums in the UK: 341.4 mm rainfall was recorded in a 24 hour period at Honister Pass, Western Lake District, and 405 mm of rainfall was recorded in a 38 hour period at Thirlmere, central Lake District. The storm was the largest in a 150 year local rainfall series, and exceeded previous new records set in the 2005 and 2009 floods. During this exceptional event, rivers over topped flood defences, and caused damage to over 257 bridges, flooded over 5000 homes and businesses, and caused substantial geomorphic change along upland rivers. This research quantifies the geomorphic and sedimentary response to Storm Desmond along a regulated gravel-bed river: St John's Beck. St John's Beck (length 7.8 km) is a channelised low gradient river (0.005) downstream of Thirlmere Reservoir, which joins the River Greta, and flows through Keswick, where major flooding has occurred, before discharging into Bassenthwaite Lake. St John's Beck has a history of chronic sediment aggradation, erosion and reports of historic flooding date back to 1750. During Storm Desmond, riverbanks were eroded, coarse sediment was deposited across valuable farmland and access routes were destroyed, including a bridge and footpaths, disrupting local business. A sediment budget framework has been used to quantify geomorphic change and sedimentary characteristics of the event along St John's Beck. The volume and sediment size distribution of flood deposits, channel bars, tributary deposits, floodplain scour, riverbank erosion and in-channel bars were measured directly in the field and converted to mass using local estimates of coarse and fine sediment bulk densities. During the event 5000 tonnes of sediment was deposited on floodplains surrounding St John's Beck; 65% of this sediment was deposited in the first 3 km of the reach downstream of Thirlmere Reservoir where the channel is unconfined and channel slope and capacity rapidly decrease. Flood sediment deposits were composed of a single layer of sediment of a similar grain size distribution (mean D90 116 mm), with fines generally sparse. The main source of sediment deposited during the event originated from the channel bed and banks; 1500 tonnes of sediment was stored within channel bars. Approximately 2000 tonnes of sediment was eroded from the riverbanks during the event; with local lateral riverbank recession exceeding 12 m. An estimated 500 tonnes of sediment was scoured from the floodplains along the first 3 km of the reach downstream of Thirlmere Reservoir, with local floodplain scour around a bridge estimated at 300 tonnes. Overall, this sediment budget study demonstrates the importance of valley systems as a major source and sink of sediment along the upland sediment cascade during an extreme flood event.

Exploring geothermal structures in the Ilan Plain, Taiwan

NASA Astrophysics Data System (ADS)

Wang, Chien-Ying; Shih, Ruey-Chan; Chung, Chen-Tung; Huang, Ming-Zi; Kuo, Hsuan-Yu

2017-04-01

The Ilan Plain in northeast Taiwan is located at the southwestern tip of the Okinawa Trough, which extends westward into the Taiwan orogeny. The Ilan Plain covered by thick sediments is clipped by the Hsuehshan Range in the northern side and the Central Range in the southern side. High geothermal gradients with plenteous hot springs of this area may result from igneous intrusion associated with the back-arc spreading of the Okinawa Trough. In this study, we use reflection seismic survey to explore underground structures in the whole Ilan Plain, especially in SanShin, Wujie, and Lize area. We aim to find the relationship between underground structures and geothermal forming mechanism. The research uses reflection seismic survey to investigate the high geothermal gradient area with two mini-vibrators and 240-channel system. The total length of seismic lines is more than 30 kilometers. The results show that alluvial sediments covering the area about 400 600 meters thick and then thin out to the west in SanShin area. In SanShin , the Taiyaqiao anticline in Hsuehshan Range has entered the plain area and is bounded by the Zhuoshui fault (south) and the Zailian fault (north). In Wujie and Lize , Zhuoshui fault cut through a strong reflector which is the top of the gravel layer near the bottom of the alluvial layer, while the SanShin fault seems to cut near very shallow strata. These two faults are a strike-slip fault with a bit of normal fault component distributing over a range of 600 meters. In Ilan Plain, the geothermal forming mechanism is controlled by anticlines and faults. The hydrothermal solution which migrates upward along these anticline or fault zones to the shallow part causing high geothermal gradients in these areas.

Chabazite and dolomite formation in a dolocrete profile: An example of a complex alkaline paragenesis in Lanzarote, Canary Islands

NASA Astrophysics Data System (ADS)

Alonso-Zarza, Ana M.; Bustamante, Leticia; Huerta, Pedro; Rodríguez-Berriguete, Álvaro; Huertas, María José

2016-05-01

This paper studies the weathering and soil formation processes operating on detrital sediments containing alkaline volcanic rock fragments of the Mirador del Río dolocrete profile. The profile consists of a lower horizon of removilised weathered basalts, an intermediate red sandy mudstones horizon with irregular carbonate layers and a topmost horizon of amalgamated carbonate layers with root traces. Formation occurred in arid to semiarid climates, giving place to a complex mineralogical association, including Mg-carbonates and chabazite, rarely described in cal/dolocretes profiles. Initial vadose weathering processes occurred in the basalts and in directly overlying detrital sediments, producing (Stage 1) red-smectites and dolomicrite. Dominant phreatic (Stage 2) conditions allowed precipitation of coarse-zoned dolomite and chabazite filling porosities. In Stages 3 and 4, mostly pedogenic, biogenic processes played an important role in dolomite and calcite accumulation in the profile. Overall evolution of the profile and its mineralogical association involved initial processes dominated by alteration of host rock, to provide silica and Mg-rich alkaline waters, suitable for chabazite and dolomite formation, without a previous carbonate phase. Dolomite formed both abiogenically and biogenically, but without a previous carbonate precursor and in the absence of evaporites. Dominance of calcite towards the profile top is the result of Mg/Ca decrease in the interstitial meteoric waters due to decreased supply of Mg from weathering, and increased supply of Ca in aeolian dust. Meteoric origin of the water is confirmed by C and O isotope values, which also indicate lack of deep sourced CO2. The dolocrete studied and its complex mineral association reveal the complex interactions that occur at surface during weathering and pedogenesis of basalt-sourced rocks.

The Caldas Novas dome, central Brazil: structural evolution and implications for the evolution of the Neoproterozoic Brasília belt

NASA Astrophysics Data System (ADS)

D'el-Rey Silva, Luiz José Homem; Wolf Klein, Percy Boris; Walde, Detlef Hans-Gert

2004-10-01

The Caldas Novas dome (Goiaás state, central Brazil) lies in the southern segment of the Neoproterozoic Brasília belt (center of the Tocantins Province) between the Goiás magmatic arc and the margin of the ancient São Francisco plate. The core of the dome comprises rocks of the Meso-Neoproterozoic Paranoá group (passive margin psamitic-pelitic sediments and subgreenschist facies) covered by a nappe of the Neoproterozoic Araxá group (backarc basin pelitic-psamitic sediments and volcanics of greenschist facies, bitotite zone). Hot underground waters that emerge along fractures in the Paranoá quartzite and wells in the Araxá schist have made the Caldas Novas dome an international tourist attraction. A recent detailed structural analysis demonstrates that the dome area was affected by a D 1-D 3 Brasiliano cycle progressive deformation in the ˜750-600 Ma interval (published U-Pb and Sm-Nd data). During event D 1, a pervasive layer-parallel foliation developed coeval the regional metamorphism. Event D 2 (intense F 2 isoclinal folding) was responsible for the emplacement of the nappe. D 1 and D 2 record a regime of simple shear (top-to-SE relative regional movement) due to a WNW-ESE subhorizontal compression ( σ1). Event D 3 records a WSW-ENE compression, during which the dome rose as a large-scale F 3 fold, possibly associated with a duplex structure at depth. During the dome's uplift, the layers slid back and down in all directions, giving way to gravity-slide folds and an extensional crenulation cleavage. A set of brittle fractures and quartz veins constitutes the record of a late-stage D 4 event important for understanding the thermal water reservoir.

Paleo-environmental interpretation of Paleocene Sepultura Formation in type locality, Mesa La sepultura, Baja California, Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arzate-Hernandez, L.; Tellezduarte, M.

1988-03-01

The Sepultura Formation in its type locality consists of two major lithostratigraphic units. The basal A unit overlies the Cretaceous Rosario Formation. It consists predominantly of fine-grained, poorly consolidated sandstones; some conglomerates; and thin beds of well-consolidated lenticular fossiliferous sandstones, which show some cyclic sedimentation. The poorly consolidated sandstones contain glauconitic layers; abundant shark teeth, benthic forams, and ostracods; and sparse mollusks, brachiopods, and Ophiomorpha-like trace fossils. These faunas indicate deposition in nearshore shallow waters. The interbedded consolidated lenticular sandstones probably indicate storm-induced deposition below wave base. This mechanism is assumed to be responsible for the high concentration of fossilsmore » consisting predominantly of unworn molluscan shells, scaphopods, echinoid spines, corals, and forams. In places, the elongated shells of Turritella pachecoensis show a preferential orientation to the southwest. At the top of the unit, a poorly fossiliferous red conglomerate indicates deltaic conditions. Overlying the conglomerate is unit B which shows a change in the sedimentary environment. It consists of a calcareous shallowing upward sequence of nodular to massive algal limestone with caliche at top. The microfossils of this unit show glauconitization in places, and consist, in addition to algal fragments, of forams, microscopic mollusks, and some ostracods and calcispherules from shallow waters (less than 30 m deep).« less

Mars mission relevant investigations on a ~ 3.5 Ga Mars analogue rock from the Pilbara and Barberton

NASA Astrophysics Data System (ADS)

Westall, F.; Pullan, D.; Schröder, C.; Klingelhöfer, G.; Fernández-Sánchez, J.; Jorge, S.; Edwards, H.; Cressey, G.

2007-08-01

Volcaniclastic sediments deposited in shallow water basins on the early Earth represent ideal analogues for Noachian volcanic sediments since the environmental conditions and settings for both were quite similar: important volcanic and hydrothermal activity (somewhat less on Mars), period of late heavy bombardment (~4.0 Ga), water bodies with a slightly acidic pH, higher salt content, atmosphere with minimal O2 (<0.2 % PAL), high UV flux to the surface. Life apparently thrived in these conditions on Earth, leaving structural and geochemical signatures in the Early Archaean sediments. Within the framework of the PAFS-net* programme, using space qualified instrumentation, we analysed previously well-characterised volcanic sedimentary rocks from a number of locations in the 3.5-3.3 Ga-old greenstone belts of the Pilbara (Australia) and Barberton (South Africa). They included mud flat sediments containing traces of probable chemolithotrophic and anoxygenic photosynthetic microorganisms, a small stromatolite (some microfossil traces) and a banded iron formation sample (also some microfossil traces). All the sediments were silicified by early diagenetic processes. The instruments used were the Beagle2 Development Model (DM) stereo camera for proximal (~100 cm) and macroscopic (~10 cm) imaging, the Beagle 2 microscope for microscopic (~1 cm) imaging, a Nuance multi-spectral imager, a TN Technologies Spectrace 9000 commercial energy dispersive XRF spectrometer, a Philips PW1710 diffractometer for XRD, and the Beagle2 spare Mössbauer spectrometer. The camera systems were well able to depict the fine-scale sedimentological structures of the rock samples that, in the case of the volcaniclastic sediment and the stromatolite, can be used to interpret a shallow water environment of deposition (the flaser-linsen bedding of the former and the convex, sinuous layering of the latter). The massively quartz-rich (chert) composition of the silicified sediments was picked up by the XRD and the Raman spectrometers. The silicified volcanics also contain feldspar, identified by the Raman, whereas the XRF analyses showed that they are K-feldspars. The traces of Ba and Cu in this sample are probably related to the mostly hydothermal origin of the silica that cemented the volcanic sediments. Raman spectroscopy also identified a greater abundance of carbon (matured kerogen) in the black layers of this sample (finer grained volcaniclastics). The stromatolite sample, on the other hand, consists largely of quartz although Raman showed some dolomite and carbon (mature kerogen) in the grey layers (silicified stromatolitic layers). The layering in the laminated volcaniclastic sediment was too fine for the Mössbauer spectrometer to pick up any details. The Mössbauer was able to detect a very thin layer of Fe oxide <<0.2 mm on the surface of the stromatolite. Compositional layering in the BIF was clearly visible using multispectral imaging with the Nuance camera and the Mössbauer could identify highly crystalline and chemically pure goethite in the Fe-rich layers with minor goethite and hematite occurring in the quartz-rich layers. The combination of the instrumentation used for imaging and chemical analysis was quite sufficient to identify the sedimentary origin of the finely laminated volcaniclastic and stromatolite rocks and to demonstrate their pervasive silicification. The presence of carbon in these rocks would, in a Mars scenario, make them ideal subjects for organo-geochemical analysis. The same suite of instruments was also able to demonstrate the origin of the BIF, again, a suitable candidate for further analysis. * Planetary Analogue Field Study network (main coordinator D. Pullan)

Genomic analysis reveals a tight link between transcription factor dynamics and regulatory network architecture.

PubMed

Jothi, Raja; Balaji, S; Wuster, Arthur; Grochow, Joshua A; Gsponer, Jörg; Przytycka, Teresa M; Aravind, L; Babu, M Madan

2009-01-01

Although several studies have provided important insights into the general principles of biological networks, the link between network organization and the genome-scale dynamics of the underlying entities (genes, mRNAs, and proteins) and its role in systems behavior remain unclear. Here we show that transcription factor (TF) dynamics and regulatory network organization are tightly linked. By classifying TFs in the yeast regulatory network into three hierarchical layers (top, core, and bottom) and integrating diverse genome-scale datasets, we find that the TFs have static and dynamic properties that are similar within a layer and different across layers. At the protein level, the top-layer TFs are relatively abundant, long-lived, and noisy compared with the core- and bottom-layer TFs. Although variability in expression of top-layer TFs might confer a selective advantage, as this permits at least some members in a clonal cell population to initiate a response to changing conditions, tight regulation of the core- and bottom-layer TFs may minimize noise propagation and ensure fidelity in regulation. We propose that the interplay between network organization and TF dynamics could permit differential utilization of the same underlying network by distinct members of a clonal cell population.

Nitrate retention capacity of milldam-impacted legacy sediments and relict A horizon soils

NASA Astrophysics Data System (ADS)

Weitzman, Julie N.; Kaye, Jason P.

2017-05-01

While eutrophication is often attributed to contemporary nutrient pollution, there is growing evidence that past practices, like the accumulation of legacy sediment behind historic milldams, are also important. Given their prevalence, there is a critical need to understand how N flows through, and is retained in, legacy sediments to improve predictions and management of N transport from uplands to streams in the context of climatic variability and land-use change. Our goal was to determine how nitrate (NO3-) is cycled through the soil of a legacy-sediment-strewn stream before and after soil drying. We extracted 10.16 cm radius intact soil columns that extended 30 cm into each of the three significant soil horizons at Big Spring Run (BSR) in Lancaster, Pennsylvania: surface legacy sediment characterized by a newly developing mineral A horizon soil, mid-layer legacy sediment consisting of mineral B horizon soil and a dark, organic-rich, buried relict A horizon soil. Columns were first preincubated at field capacity and then isotopically labeled nitrate (15NO3-) was added and allowed to drain to estimate retention. The columns were then air-dried and subsequently rewet with N-free water and allowed to drain to quantify the drought-induced loss of 15NO3- from the different horizons. We found the highest initial 15N retention in the mid-layer legacy sediment (17 ± 4 %) and buried relict A soil (14 ± 3 %) horizons, with significantly lower retention in the surface legacy sediment (6 ± 1 %) horizon. As expected, rewetting dry soil resulted in 15N losses in all horizons, with the greatest losses in the buried relict A horizon soil, followed by the mid-layer legacy sediment and surface legacy sediment horizons. The 15N remaining in the soil following the post-drought leaching was highest in the mid-layer legacy sediment, intermediate in the surface legacy sediment, and lowest in the buried relict A horizon soil. Fluctuations in the water table at BSR which affect saturation of the buried relict A horizon soil could lead to great loses of NO3- from the soil, while vertical flow through the legacy-sediment-rich soil profile that originates in the surface has the potential to retain more NO3-. Restoration that seeks to reconnect the groundwater and surface water, which will decrease the number of drying-rewetting events imposed on the relict A horizon soils, could initially lead to increased losses of NO3- to nearby stream waters.

Field observation and analysis of wave-current-sediment movement in Caofeidian Sea area in the Bohai Bay, China

NASA Astrophysics Data System (ADS)

Zuo, Li-qin; Lu, Yong-jun; Wang, Ya-ping; Liu, Huai-xiang

2014-06-01

In order to study the mechanism of flow-sediment movement, it is essential to obtain measured data of water hydrodynamic and sediment concentration process with high spatial and temporal resolution in the bottom boundary layer (BBL). Field observations were carried out in the northwest Caofeidian sea area in the Bohai Bay. Near 2 m isobath (under the lowest tidal level), a tripod system was installed with AWAC (Acoustic Wave And Current), ADCP (Acoustic Doppler Current Profilers), OBS-3A (Optical Backscatter Point Sensor), ADV (Acoustic Doppler Velocimeters), etc. The accurate measurement of the bottom boundary layer during a single tidal period was carried out, together with a long-term sediment concentration measurement under different hydrological conditions. All the measured data were used to analyze the characteristics of wave-current-sediment movement and the BBL. Analysis was performed on flow structure, shear stress, roughness, eddy viscosity and other parameters of the BBL. Two major findings were made. Firstly, from the measured data, the three-layer distribution model of the velocity profiles and eddy viscosities in the wave-current BBL are proposed in the observed sea area; secondly, the sediment movement is related closely to wind-waves in the muddy coast area where sediment is clayey silt: 1) The observed suspended sediment concentration under light wind conditions is very low, with the peak value generally smaller than 0.1 kg/m3 and the average value being 0.03 kg/m3; 2) The sediment concentration increases continuously under the gales over 6-7 in Beaufort scale, under a sustained wind action. The measured peak sediment concentration at 0.4 m above the seabed is 0.15-0.32 kg/m3, and the average sediment concentration during wind-wave action is 0.08-0.18 kg/m3, which is about 3-6 times the value under light wind conditions. The critical wave height signaling remarkable changes of sediment concentration is 0.5 m. The results show that the suspended load sediment concentration is mainly influenced by wave-induced sediment suspension.

A multi-level pore-water sampler for permeable sediments

USGS Publications Warehouse

Martin, J.B.; Hartl, K.M.; Corbett, D.R.; Swarzenski, P.W.; Cable, J.E.

2003-01-01

The construction and operation of a multi-level piezometer (multisampler) designed to collect pore water from permeable sediments up to 230 cm below the sediment-water interface is described. Multisamplers are constructed from 1 1/2 inch schedule 80 PVC pipe. One-quarter-inch flexible PVC tubing leads from eight ports at variable depths to a 1 1/2 inch tee fitting at the top of the PVC pipe. Multisamplers are driven into the sediments using standard fence-post drivers. Water is pumped from the PVC tubing with a peristaltic pump. Field tests in Banana River Lagoon, Florida, demonstrate the utility of multisamplers. These tests include collection of multiple samples from the permeable sediments and reveal mixing between shallow pore water and overlying lagoon water.

In Situ, High-Resolution Profiles of Labile Metals in Sediments of Lake Taihu

PubMed Central

Wang, Dan; Gong, Mengdan; Li, Yangyang; Xu, Lv; Wang, Yan; Jing, Rui; Ding, Shiming; Zhang, Chaosheng

2016-01-01

Characterizing labile metal distribution and biogeochemical behavior in sediments is crucial for understanding their contamination characteristics in lakes, for which in situ, high-resolution data is scare. The diffusive gradient in thin films (DGT) technique was used in-situ at five sites across Lake Taihu in the Yangtze River delta in China to characterize the distribution and mobility of eight labile metals (Fe, Mn, Zn, Ni, Cu, Pb, Co and Cd) in sediments at a 3 mm spatial resolution. The results showed a great spatial heterogeneity in the distributions of redox-sensitive labile Fe, Mn and Co in sediments, while other metals had much less marked structure, except for downward decreases of labile Pb, Ni, Zn and Cu in the surface sediment layers. Similar distributions were found between labile Mn and Co and among labile Ni, Cu and Zn, reflecting a close link between their geochemical behaviors. The relative mobility, defined as the ratio of metals accumulated by DGT to the total contents in a volume of sediments with a thickness of 10 mm close to the surface of DGT probe, was the greatest for Mn and Cd, followed by Zn, Ni, Cu and Co, while Pb and Fe had the lowest mobility; this order generally agreed with that defined by the modified BCR approach. Further analyses showed that the downward increases of pH values in surface sediment layer may decrease the lability of Pb, Ni, Zn and Cu as detected by DGT, while the remobilization of redox-insensitive metals in deep sediment layer may relate to Mn cycling through sulphide coprecipitation, reflected by several corresponding minima between these metals and Mn. These in situ data provided the possibility for a deep insight into the mechanisms involved in the remobilization of metals in freshwater sediments. PMID:27608033

Improvement of resist profile roughness in bilayer resist process

NASA Astrophysics Data System (ADS)

Jeong, Chang-Young; Ryu, Sang-Wook; Park, Ki-Yeop; Lee, Won-Kyu; Lee, Seung-Woog; Lee, Dai-Hoon

2000-06-01

The bi-layer resist (BLR) process, which first accomplish imaging on a thin top layer and transfer it down to a thick organic layer, is one of newly emerging patterning techniques in silicon processing. In this work, we studied the lithographic performance of the BLR process adopting FK- SPTM (Fujifilm Olin Co.) as top layer material and various organic material as bottom layer. Generally, considerable advantages of planarization, reduced substrate reflection, improved process latitude, and of enhanced resolution are achieved. However, the resolution and the process latitude are highly affected by surface interaction between the top resist and the bottom material. Moreover, the BLR process has a sidewall roughness problem related to the material factors of the resist and the degraded aerial image contrast, which can affect the reliability of the device. We found that thermal curing treatment applied after development with the consideration of the glass transition temperature are very effective in reducing the line edge roughness. More smooth and steep patterning is achieved by the thermal treatment. The linewidth controllability is below 10 nm and the k1 value is reduced from 0.5 down to 0.32 in this process. The reactive ion etching adopting O2 gas demonstrated selectivity of the top resist over bottom material more than 15:1, together with residue-free and vertical wall profile.

Ripple structure of crystalline layers in ion-beam-induced Si wafers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hazra, S.; Chini, T.K.; Sanyal, M.K.

Ion-beam-induced ripple formation in Si wafers was studied by two complementary surface sensitive techniques, namely atomic force microscopy (AFM) and depth-resolved x-ray grazing incidence diffraction (GID). The formation of ripple structure at high doses ({approx}7x10{sup 17} ions/cm{sup 2}), starting from initiation at low doses ({approx}1x10{sup 17} ions/cm{sup 2}) of ion beam, is evident from AFM, while that in the buried crystalline region below a partially crystalline top layer is evident from GID study. Such ripple structure of crystalline layers in a large area formed in the subsurface region of Si wafers is probed through a nondestructive technique. The GID techniquemore » reveals that these periodically modulated wavelike buried crystalline features become highly regular and strongly correlated as one increases the Ar ion-beam energy from 60 to 100 keV. The vertical density profile obtained from the analysis of a Vineyard profile shows that the density in the upper top part of ripples is decreased to about 15% of the crystalline density. The partially crystalline top layer at low dose transforms to a completely amorphous layer for high doses, and the top morphology was found to be conformal with the underlying crystalline ripple.« less

Titanium aluminide intermetallic alloys with improved wear resistance

DOEpatents

Qu, Jun; Lin, Hua-Tay; Blau, Peter J.; Sikka, Vinod K.

2014-07-08

The invention is directed to a method for producing a titanium aluminide intermetallic alloy composition having an improved wear resistance, the method comprising heating a titanium aluminide intermetallic alloy material in an oxygen-containing environment at a temperature and for a time sufficient to produce a top oxide layer and underlying oxygen-diffused layer, followed by removal of the top oxide layer such that the oxygen-diffused layer is exposed. The invention is also directed to the resulting oxygen-diffused titanium aluminide intermetallic alloy, as well as mechanical components or devices containing the improved alloy composition.

Convection in an ideal gas at high Rayleigh numbers.

PubMed

Tilgner, A

2011-08-01

Numerical simulations of convection in a layer filled with ideal gas are presented. The control parameters are chosen such that there is a significant variation of density of the gas in going from the bottom to the top of the layer. The relations between the Rayleigh, Peclet, and Nusselt numbers depend on the density stratification. It is proposed to use a data reduction which accounts for the variable density by introducing into the scaling laws an effective density. The relevant density is the geometric mean of the maximum and minimum densities in the layer. A good fit to the data is then obtained with power laws with the same exponent as for fluids in the Boussinesq limit. Two relations connect the top and bottom boundary layers: The kinetic energy densities computed from free fall velocities are equal at the top and bottom, and the products of free fall velocities and maximum horizontal velocities are equal for both boundaries.

Magnetic signatures of Heinrich-like detrital layers in the Quaternary of the North Atlantic

NASA Astrophysics Data System (ADS)

Channell, J. E. T.; Hodell, D. A.

2013-05-01

Magnetic parameters are useful for distinguishing North Atlantic Heinrich-like detrital layers from background sediments. Here we compare magnetic properties with XRF scanning data back to 700 ka and 1.3 Ma at IODP Sites U1302-U1303 and U1308, respectively. Multi-domain magnetite, with grain sizes >20 µm, is characteristic of both Ca- and Si-rich detrital layers, as defined by XRF core scanning, confirming the contribution of ice rafting. Reflectance spectra and magnetic parameters distinguish Ca- and Si-rich IRD layers due the presence of high coercivity hematite in Si-rich layers. Heinrich layer 6 (H6) at Site U1302-U1303 is unlike other detrital layers, being marked by a 45-cm thick homogeneous cream-colored clay layer underlain by a thin (5-cm) graded coarse-sand. Comparison of Site U1302/03 and Site U1308 detrital layers implies a dominant Laurentide source for both Ca- and Si-rich detrital layers. At Site U1308, low benthic δ13C values during stadials are in-step with magnetic grain-size coarsening associated with Si-rich detrital layers back to 1.3 Ma, indicating a link between deep-sea ventilation and ice rafting. The surface-sediment tan-colored oxic layer (~2 m thick at Site U1308) yields magnetic hysteresis ratios that are offset from the single-domain to multi-domain (SD-MD) magnetite mixing-line in hysteresis-ratio diagrams. This offset is attributed to maghemite grain-coatings, that form on magnetite in surface sediment, and undergo dissolution as they pass through the oxic/anoxic boundary.

Velocity of water flow along saturated loess slopes under erosion effects

NASA Astrophysics Data System (ADS)

Huang, Yuhan; Chen, Xiaoyan; Li, Fahu; Zhang, Jing; Lei, Tingwu; Li, Juan; Chen, Ping; Wang, Xuefeng

2018-06-01

Rainfall or snow-melted water recharge easily saturates loose top soils with a less permeable underlayer, such as cultivated soil slope and partially thawed top soil layer, and thus, may influence the velocity of water flow. This study suggested a methodology and device system to supply water from the bottom soil layer at the different locations of slopes. Water seeps into and saturates the soil, when the water level is controlled at the same height of the soil surface. The structures and functions of the device, the components, and the operational principles are described in detail. A series of laboratory experiments were conducted under slope gradients of 5°, 10°, 15°, and 20° and flow rates of 2, 4, and 8 L min-1 to measure the water flow velocities over eroding and non-eroded loess soil slopes, under saturated conditions by using electrolyte tracing. Results showed that flow velocities on saturated slopes were 17% to 88% greater than those on non-saturated slopes. Flow velocity increased rapidly under high flow rates and slope gradients. Saturation conditions were suitable in maintaining smooth rill geomorphology and causing fast water flow. The saturated soil slope had a lubricant effect on the soil surface to reduce the frictional force, resulting in high flow velocity. The flow velocities of eroding rills under different slope gradients and flow rates were approximately 14% to 33% lower than those of non-eroded rills on saturated loess slopes. Compared with that on a saturated loess slope, the eroding rill on a non-saturated loess slope can produce headcuts to reduce the flow velocity. This study helps understand the hydrodynamics of soil erosion and sediment transportation of saturated soil slopes.

Geology of the Carnegie museum dinosaur quarry site of Diplodocus carnegii, Sheep Creek, Wyoming

USGS Publications Warehouse

Brezinski, D.K.; Kollar, A.D.

2008-01-01

The holotype of Diplodocus carnegii Hatcher, 1901, consists of a partial skeleton (CM 84) that was recovered, along with a second partial skeleton of the same species (CM 94), from the upper 10 m of the Talking Rock facies of the Brushy Basin Member of the Morrison Formation exposed along Bone Quarry Draw, a tributary of Sheep Creek in Albany County, Wyoming. A composite measured section of the stratigraphic interval exposed adjacent to the quarry indicates that the Brushy Basin Member in this area is a stacked succession of lithofacies consisting of hackly, greenish gray, calcareous mudstone and greenish brown, dense, fine-grained limestone. The more erosion resistant limestone layers can be traced over many hundreds of meters. Thus, these strata do not appear to represent a highly localized deposit such as a stream channel, oxbow lake, or backwater pond. The Sheep Creek succession is interpreted as representing a clastic-dominated lake where high turbidity and sediment influx produced deposition of calcareous mudstone. During drier periods the lake's turbidity decreased and limestone and dolomite precipitation replaced mud deposition. Microkarsting at the top of some limestone/ dolomite layers suggests subaerial deposition may have prevailed during these dry episodes. The quarry of D. carnegii was excavated within the top strata of one of the numerous intervals of hackly, greenish gray, calcareous mudstone that represent an ephemeral freshwater lake. The quarry strata are directly overlain by 0.3 m of dolomite-capped limestone that was deposited shortly after interment of D. carnegii in the lake mudstones. The close vertical proximity of the overlying limestone to the skeleton's stratigraphic: level suggests that the animal's carcass may have been buried beneath the drying lake deposits during a period of decreased rainfall.

Structure and development of the Southeast Georgia Embayment and northern Blake Plateau: Preliminary analysis

USGS Publications Warehouse

Dillon, William P.; Paull, Charles K.; Buffler, Richard T.; Fail, Jean-Pierre

1979-01-01

Multichannel seismic reflection profiles from the Southeast Georgia Embayment and northern Blake Plateau show reflectors that have been correlated tentatively with horizons of known age. The top of the Cretaceous extends smoothly seaward beneath the continental shelf and Blake Plateau, unaffected at the present shelf edge. A reflector inferred to correspond approximately to the top of the Jurassic section onlaps and pinches out against rocks below. A widespread smooth reflector probably represents a volcanic layer of Early Jurassic age that underlies only the northwestern part of the research area. A major unconformity beneath the inferred volcanic layer is probably of Late Triassic or Early Jurassic age. This unconformity dips rather smoothly seaward beneath the northern Blake Plateau, but south of a geological boundary near 31°N, it has subsided much more rapidly, and reaches depths of more than 12 km. Development of the continental margin north of the boundary began with rifting and subsidence of continental basement in the Triassic. An episode of volcanism may have been due to stresses associated with a spreading center jump at about 175 million years ago. Jurassic and Cretaceous deposits form an onlapping wedge above the inferred early Jurassic volcanics and Triassic sedimentary rocks. During Cenozoic times, development of Gulf Stream flow caused a radical decrease in sedimentation rates so that a shelf that was much narrower than the Mesozoic shelf was formed by progradation against the inner edge of the stream. South of the 31°N geological boundary, the basement probably is semi-oceanic and reef growth, unlike that in the area to the north, has been very active at the outer edge of the plateau.

Processes of Geology

NASA Technical Reports Server (NTRS)

2003-01-01

[figure removed for brevity, see original site]

Released 16 July 2003

This THEMIS visible image captures a complex process of deposition, burial and exhumation. The crater ejecta in the top of the image is in the form of flow lobes, indicating that the crater was formed in volatile-rich terrain. While a radial pattern can be seen in the ejecta, the pattern is sharper in the lower half of the ejecta. This is because the top half of the ejecta is still buried by a thin layer of sediment. It is most likely that at one time the entire area was covered. Wind, and perhaps water erosion have started to remove this layer, once again exposing the what was present underneath.

Image information: VIS instrument. Latitude -34.3, Longitude 181.2 East (178.8 West). 19 meter/pixel resolution.

Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

Depth-dependent erodibility: representing burnt soils as a two-layered cohesive/non-cohesive system

NASA Astrophysics Data System (ADS)

Nyman, P.; Sheridan, G. J.; Moody, J. A.; Smith, H. G.; Lane, P. N.

2011-12-01

Immediately after wildfire there is an abundant supply of non-cohesive ash, soil and gravel which is easily entrained by overland flow. Under these conditions the sediment flux on hillslopes can be assumed to be equal to the transport capacity of the flow. However, the supply of material is finite and at some point the hillslope could shift towards a system where entrainment is restricted by armouring and soil cohesion. In this study we test the notion that burnt hillslopes can be represented as a two-layered system of non-cohesive and cohesive soils. Using a combination of i) shear vane measurements, ii) confined hillslope flow experiments and iii) a laboratory flume, we demonstrate how erosion on burnt hillslopes primarily takes place in a distinct layer of non-cohesive soil with erosion properties that are very different to the underlying soil matrix. Shear vane measurements were taken at 5 soil depths at more than 50 points along transects in order to quantify the depth and spatial distribution of non-cohesive soil in two small (0.5 ha) and steep (30 deg) convergent basins (SE Australia) that were burnt at high severity. The measurements showed that the recently burnt hillslopes were mantled with non-cohesive soil to an average depth of 18mm and 20mm at the two sites which were situated in different geologic terrain but in similar eucalyptus dominated forests. In the hillslope flow experiments, the rapid entrainment of non-cohesive material resulted in very high sediment concentration (50-60% by volume) in the initial surge from the test area. During the flow experiments the sediment concentration decreased exponentially with time until the erosion rate reached a steady state reflecting the erodibility of the underlying cohesive soil. The formation of shallow rills and the presence of large clasts (>16cm) within the test area resulted in incomplete removal of the non-cohesive material at shear stress < 50 Ncm-2. At shear stress > 50 Ncm-2 all material was removed, and the erosion depth at the end of the experiments was equal to the depth of non-cohesive material measured using the shear vane. In a separate set of experiments, a laboratory flume was used to measure the erodibility at different soil depths using soil cores that were burnt at moderate to high severity. Unlike the field based flow experiments, the erodibility measurements of non-cohesive soils in the flume were not restricted by the transport capacity of the flow. Results from the flume experiments showed a two order of magnitude decrease in erodibility within the top 2cm of the soil profile for soil cores from both chaparral and coniferous forests (western US). In summary, these results indicate that a majority of hillslope sediment may be generated from a relatively shallow layer of non-cohesive and highly erodible material. The depth of this material may be an important property that can help determine the post-fire erosion and debris flow potential, particularly in systems where other sources of sediment are limited. The study confirms that erodibility of burnt soil shows strong variation with depth and that the assumption of a constant erodibility factor may lead to misrepresentation of important processes.

Identification And Survival Of Bacteriohopanepolyol In A Hot Spring Microbial Mat

NASA Technical Reports Server (NTRS)

Janke, Linda L.; Chang, Sherwood (Technical Monitor)

1995-01-01

The polar lipids of a hot spring microbial mat located in Yellowstone National Park were examined for the presence of bacteriohopanepolvols (BHP). BHP are a group of molecules consisting of a hopanoid (peotacyclic triterpene) linked via a n-alkyl polyhydroxylated chain to a variety of polar end groups. BHP have been isolated in varying amounts from phylogenetically diverse eubacterial groups including cyanobacteria, methanotrophs and the Rhodospirillaceae. The hopanoids are excellent biomarkers and have been detected in sedimentary rocks as old as 1.7 bya. In order to interpret the ancient organic record, it is important to understand the abundance, source and fate of such biomarker compounds in microbial mats. A 40 sq cm mat section was taken from a 52 to 55 C site in the effluent channel of Octopus Spring and was sampled vertically over approximately 16 mm. The first 5-6 mm was sectioned into a top green layer (310 mg dry weight) and several subjacent, deep orange layers (240 and 250 mg, respectively). The lower 10 mm of the mat was sectioned into two gelatinous orange layers containing a siliceous gritty material (260 and 440 mg) which increased with depth, and a bottom layer composed almost exclusively of siliceous sinter (4.1 g). The progressive decrease in total organic carbon from 45% in the top green layer to only 4% in the bottom layer reflects the observed increase in siliceous deposition. GC-MS analysis of the phospholipid and glycolipid fatty acids yielded predominantly saturated normal chain acids, n-15 to n-18, and iso-branched acids, i-15 to i-17. Small amounts of unsaturated fatty acids (16:1, two positional isomers of 18:1, and two cyclopropyl acids, C(sub 17) and C(sub 19)) were present mainly in the top layer. Esterified fatty acid which is a good index for intact cellular membrane, i.e. viable organisms, was highest in the top two layers (203 and 231 micro g/mg total lipid, respectively) and gradually decreased to 66 micro g/mg total lipid in the bottom layer. Small amounts of BHP were present in all six layers, however in this case, BHP was lowest in the top green and subjacent deep-orange layers (118 and 172 micro g/mg total lipid, respectively) and increased with depth reaching almost 400 micro g/mg in the bottom two layers. This data suggest that BHP are survivina the initial phase of mat degradation and may be preferentially enriched in any organic record of such thermal environments. The relatively low level of BHP in the top layer also suggests that cyanobacteria may not be the major source of BHP in this mat. Since Chloroflexus a major component of the deep-orange layer has been reported to lack BHP, this material may prove a valuable biomarker for some other mat inhabitant. Further isotopic characterization of this BHP should help resolve this finding.

Enhanced sorption of PAHs in natural-fire-impacted sediments from Oriole Lake, California.

PubMed

Sullivan, Julia; Bollinger, Kevyn; Caprio, Anthony; Cantwell, Mark; Appleby, Peter; King, John; Ligouis, Bertrand; Lohmann, Rainer

2011-04-01

Surface sediment cores from Oriole Lake (CA) were analyzed for organic carbon (OC), black carbon (BC), and their δ(13)C isotope ratios. Sediments displayed high OC (20-25%) and increasing BC concentrations from ∼0.40% (in 1800 C.E.) to ∼0.60% dry weight (in 2000 C.E.). Petrographic analysis confirmed the presence of fire-derived carbonaceous particles/BC at ∼2% of total OC. Natural fires were the most likely cause of both elevated polycyclic aromatic hydrocarbon (PAH) concentrations and enhanced sorption in Oriole Lake sediments prior to 1850, consistent with their tree-ring-based fire history. In contrast to other PAHs, retene and perylene displayed decreasing concentrations during periods with natural fires, questioning their use as fire tracers. The occurrence of natural fires, however, did not result in elevated concentrations of black carbon or chars in the sediments. Only the 1912-2007 sediment layer contained anthropogenic particles, such as soot BC. In this layer, combining OC absorption with adsorption to soot BC (using a Freundlich coefficient n = 0.7) explained the observed sorption well. In the older layers, n needed to be 0.3 and 0.5 to explain the enhanced sorption to the sediments, indicating the importance of natural chars/inertinites in sorbing PAHs. For phenanthrene, values of n differed significantly between sorption to natural chars (0.1-0.4) and sorption to anthropogenic black carbon (>0.5), suggesting it could serve as an in situ probe of sorbents.