Short daily exposure to hand-arm vibrations in Swedish car mechanics.

PubMed

Barregård, Lars

2003-01-01

The aim of the study was to examine the daily exposure times to hand-arm vibrations in Swedish car mechanics, to test a method for estimating the exposure time without observing the workers for whole days, and to use the results for predicting the prevalence of vibration-induced white fingers (VWF) by the ISO 5349-model. Six garages were surveyed. In each garage, 5-10 car mechanics were observed in random order every 30 seconds throughout working days. The daily exposure time for each mechanic was estimated from the fraction of the observations that the mechanic was exposed. A total of 51 mechanics were observed, most of them on two different working days, yielding estimates for 95 days. The median effective exposure time was 10 minutes per day (95% confidence interval 5-15 minutes, arithmetic mean 14 minutes, maximum 80 minutes), and most of the exposure time was attributable to fastening and loosening nuts. The within-worker and between-worker variability was high (total sigma2 0.99, geometric standard deviation of 2.7). Using the observed exposure time and data on vibration levels of the main tools in Swedish car mechanics (average weighted acceleration level of 3.5 m/s2), the model in ISO-standard 5349 would predict that only three percent of the car mechanics will suffer from VWF after 20 years of exposure. In contrast, a recent survey of VWF showed the prevalence to be 25 percent. The precision of the observation method was estimated and was found to be good for the group daily mean. On the individual level the precision was only acceptable if the daily exposure time was > or = 40 minutes. In conclusion, the daily exposure time was short and the vibration level was limited. Nevertheless, hand-arm vibrations cause VWF in a significant number of car mechanics. The method of observing workers intermittently seemed to work well.

Characterizing new compositions of [001]C relaxor ferroelectric single crystals using a work-energy model

NASA Astrophysics Data System (ADS)

Gallagher, John A.

2016-04-01

The desired operating range of ferroelectric materials with compositions near the morphotropic phase boundary is limited by field induced phase transformations. In [001]C cut and poled relaxor ferroelectric single crystals the mechanically driven ferroelectric rhombohedral to ferroelectric orthorhombic phase transformation is hindered by antagonistic electrical loading. Instability around the phase transformation makes the current experimental technique for characterization of the large field behavior very time consuming. Characterization requires specialized equipment and involves an extensive set of measurements under combined electrical, mechanical, and thermal loads. In this work a mechanism-based model is combined with a more limited set of experiments to obtain the same results. The model utilizes a work-energy criterion that calculates the mechanical work required to induce the transformation and the required electrical work that is removed to reverse the transformation. This is done by defining energy barriers to the transformation. The results of the combined experiment and modeling approach are compared to the fully experimental approach and error is discussed. The model shows excellent predictive capability and is used to substantially reduce the total number of experiments required for characterization. This decreases the time and resources required for characterization of new compositions.

Research concerning the balancing of a plane mechanism

NASA Astrophysics Data System (ADS)

Bădoiu, D.; Petrescu, M. G.; Antonescu, N. N.; Toma, G.

2018-01-01

By statically balancing of the plane mechanisms and especially those functioning at high speeds is being pursued the decrease of the value of the resultant force of all inertia forces that work on the component elements, thus obtaining a significant decrease in vibrations and shocks during the functioning. On the other hand, the existence of balancing masses which ensure the balancing of the mechanism leads to increased gauge and its mass. In this paper are presented some possibilities of statically balancing a plane mechanism which is composed of three independent contours. First is analyzed the case when the mechanism is totally balanced. Then a solution is proposed for a partial balancing of the mechanism based on the balancing of the first harmonic of the inertia force developed in a piston of the mechanism. Finally, are presented some simulation results concerning the variation of the value of the resultant inertia force during a cinematic cycle when the mechanism is unbalanced and when it is partially balanced. Also, it is analyzed the variation of the motor moment when the mechanism is unbalanced and when is totally and partially balanced.

Do work-related mechanical and psychosocial factors contribute to the social gradient in long-term sick leave: a prospective study of the general working population in Norway.

PubMed

Sterud, Tom; Johannessen, Håkon A

2014-05-01

A social gradient in long-term sick leave (LTSL) rates is well established, but only a few studies have examined to what extent this gradient may be explained by mechanical and psychosocial work environment factors. A randomly drawn cohort from the general population in Norway, aged 18-69 years, was interviewed in the second half of 2009 (n=12,255, response at baseline 60.9%) and followed up in national registries to the end of 2010. Eligible respondents were registered with an active employee relationship of at least 100 actual working days in 2009 and 2010 (n=6758). Based on administrative register data, respondents were coded into five educational levels (university/college ≥4 years was set as the reference group). Eight work-related psychosocial factors and 10 mechanical exposures were measured. The outcome of interest was medically confirmed LTSL ≥40 working days during 2010. In total, 9.4% (635 individuals) were classified with LTSL during 2010. There was a strong social gradient ranging from 12.4% (elementary) to 3.3% (university/college ≥4 years) among men. The corresponding figures among women were 15.4 and 4.6%. Adjusting for work-related mechanical and psychosocial factors explained between 41 and 44% of the social gradient in men. Among women, the corresponding figures were 31 and 54%. Work-related mechanical and psychosocial factors contribute to the social gradient in LTSL. The work-related factors that accounted for this gradient were rather similar for men and women.

Biomechanical evaluation of an innovative spring-loaded axillary crutch design.

PubMed

Zhang, Yanxin; Liu, Guangyu; Xie, Shengquan; Liger, Aurélien

2011-01-01

We evaluated an innovative spring-loaded crutch design by comparing its performance with standard crutches through a biomechanical approach. Gait analysis was conducted for 7 male subjects under two conditions: walking with standard crutches and with spring-loaded crutches. Three-dimensional kinematic data and ground reaction force were recorded. Spatiotemporal variables, external mechanical work, and elastic energy (for spring crutches) were calculated based on recorded data. The trajectories of vertical ground reaction forces with standard crutches had two main peaks before and after mid-stance, and those with optimized spring-loaded crutches had only one main peak. The magnitude of external mechanical work was significantly higher with spring-loaded crutches than with standard crutches for all subjects, and the transferred elastic energy made an important contribution to the total external work for spring-loaded crutches. No significant differences in the spatiotemporal parameters were observed. Optimized spring-loaded crutches can efficiently propel crutch walkers and could reduce the total energy expenditure in crutch walking. Further research using optimized spring-loaded crutches with respect to energy efficiency is recommended.

Changes in Energy Cost and Total External Work of Muscles in Elite Race Walkers Walking at Different Speeds

PubMed Central

Chwała, Wiesław; Klimek, Andrzej; Mirek, Wacław

2014-01-01

The aim of the study was to assess energy cost and total external work (total energy) depending on the speed of race walking. Another objective was to determine the contribution of external work to total energy cost of walking at technical, threshold and racing speed in elite competitive race walkers. The study involved 12 competitive race walkers aged 24.9 4.10 years with 6 to 20 years of experience, who achieved a national or international sports level. Their aerobic endurance was determined by means of a direct method involving an incremental exercise test on the treadmill. The participants performed three tests walking each time with one of the three speeds according to the same protocol: an 8-minute walk with at steady speed was followed by a recovery phase until the oxygen debt was repaid. To measure exercise energy cost, an indirect method based on the volume of oxygen uptake was employed. The gait of the participants was recorded using the 3D Vicon opto-electronic motion capture system. Values of changes in potential energy and total kinetic energy in a gate cycle were determined based on vertical displacements of the centre of mass. Changes in mechanical energy amounted to the value of total external work of muscles needed to accelerate and lift the centre of mass during a normalised gait cycle. The values of average energy cost and of total external work standardised to body mass and distance covered calculated for technical speed, threshold and racing speeds turned out to be statistically significant (p 0.001). The total energy cost ranged from 51.2 kJ.m-1 during walking at technical speed to 78.3 kJ.m-1 during walking at a racing speed. Regardless of the type of speed, the total external work of muscles accounted for around 25% of total energy cost in race walking. Total external work mainly increased because of changes in the resultant kinetic energy of the centre of mass movement. PMID:25713673

Work-related gender differences in physician-certified sick leave: a prospective study of the general working population in Norway.

PubMed

Sterud, Tom

2014-07-01

This study aimed to examine gender differences in physician-certified sick leave and the extent to which these differences can be explained by work-related psychosocial and mechanical risk factors. Randomly drawn from the general population in Norway, the cohort comprised working men and women aged 18-69 years (N=12 255, response rate at baseline = 60.9%). Eligible respondents were interviewed in 2009 and registered with an active employee relationship of ≥ 100 actual working days in 2009 and 2010 (N=3688 men and 3070 women). The study measured 11 work-related psychosocial factors and 11 mechanical exposures, and outcomes of interest were physician-certified general sick leave (GSL) >0 days and long-term sick leave (LTSL) ≥ 40 working days during 2010. Women reported a significantly higher level of exposure to 9 of the 11 psychosocial factors evaluated. For mechanical factors, the reporting was mixed. After controlling for age, educational level, sick leave during 2009, housework, working hours and family status, a 1.7-fold risk for GSL and LTSL were found among women. In comparison with the initial model, adjusting for psychosocial factors reduced the excess risk by 21% and 27% for GSL and LTSL, respectively. The total effect of mechanical factors was negligible. Differences between occupations held by women and men explained an additional one-tenth of the excess risk for LTSL among women. Work-related psychosocial factors contributed significantly to a higher level of GSL and LTSL among women. The most important factors were demands for hiding emotions, emotional demands, and effort-payment imbalance.

Consumable and Refundable Supplies Items for Production Agriculture Mechanics Laboratories as Influenced by Selected Characteristics of Vocational Agriculture Program and Teacher. Final Report.

ERIC Educational Resources Information Center

Gerstenlauer, David L.

This study was conducted to develop a list of basic consumable and refundable supplies to be used in a secondary agricultural production mechanics laboratory program in Pennsylvania. A total of 72 surveys were sent to selected teachers: 24 in the area of woodworking, 24 in the area of metal working, and 24 covering all other areas of agricultural…

Soft Tissue Deformations Contribute to the Mechanics of Walking in Obese Adults

PubMed Central

Fu, Xiao-Yu; Zelik, Karl E.; Board, Wayne J.; Browning, Raymond C.; Kuo, Arthur D.

2014-01-01

Obesity not only adds to the mass that must be carried during walking, but also changes body composition. Although extra mass causes roughly proportional increases in musculoskeletal loading, less well understood is the effect of relatively soft and mechanically compliant adipose tissue. Purpose To estimate the work performed by soft tissue deformations during walking. The soft tissue would be expected to experience damped oscillations, particularly from high force transients following heel strike, and could potentially change the mechanical work demands for walking. Method We analyzed treadmill walking data at 1.25 m/s for 11 obese (BMI > 30 kg/m2) and 9 non-obese (BMI < 30 kg/m2) adults. The soft tissue work was quantified with a method that compares the work performed by lower extremity joints as derived using assumptions of rigid body segments, with that estimated without rigid body assumptions. Results Relative to body mass, obese and non-obese individuals perform similar amounts of mechanical work. But negative work performed by soft tissues was significantly greater in obese individuals (p= 0.0102), equivalent to about 0.36 J/kg vs. 0.27 J/kg in non-obese individuals. The negative (dissipative) work by soft tissues occurred mainly after heel strike, and for obese individuals was comparable in magnitude to the total negative work from all of the joints combined (0.34 J/kg vs. 0.33 J/kg for obese and non-obese adults, respectively). Although the joints performed a relatively similar amount of work overall, obese individuals performed less negative work actively at the knee. Conclusion The greater proportion of soft tissues in obese individuals results in substantial changes in the amount, location, and timing of work, and may also impact metabolic energy expenditure during walking. PMID:25380475

The effects of real and artificial Leg Length Discrepancy on mechanical work and energy cost during the gait.

PubMed

Assogba, T F; Boulet, S; Detrembleur, C; Mahaudens, P

2018-01-01

The impacts of Leg Length Discrepancy (LLD) on the kinematic and dynamic parameters of walking have been widely discussed. But little is known on total mechanical work and energy cost. These two variables are more representative of the functional impairment undergone by the LLD patients. To assess the changes of the mechanical work and energy cost of walking in subjects with real LLD and to compare their results with healthy subjects in whom the LLD has been simulated. The mechanical work and energy cost data of 60 healthy subjects (speed: 4km/h) with artificial LLD induced by soles (2 and 4cm), 20 patients (speed: 3.75±0.5km/h) with real LLD and 20 matched subjects (speed: 3.75±0.5km/h) were collected. Statistical comparisons between the groups were performed using a t-paired test and ANOVA. Patients with a real LLD showed a significant decrease in mechanical work and energy cost when compared to norms. Patients with real LLD provide a better recovery when compared to subjects with artificial LLD of 2cm, and a decrease of energy cost and higher muscular efficiency (mechanical work/energy cost) when compared to subjects with artificial LLD of 4cm. Our results showed that patients with a real LLD develop compensatory strategies during gait, probably to minimize the displacement of the body center of mass and consequently reduce the amount of energy expenditure useful for their displacement. Moreover, they adopt a better gait strategy compared to the subjects in whom LLD was simulated. Copyright © 2017 Elsevier B.V. All rights reserved.

The Total Library *

PubMed Central

Annan, Gertrude L.

1968-01-01

Changing functions and techniques of today's libraries have led to questioning the very substance of the library of the future. Ralph Shaw points out that the total library must be “a living force for the enrichment of mankind.” The Medical Research Library of Brooklyn at its very inauguration is uniquely prepared and equipped to work toward that goal. It imaginatively serves the needs of the immediate area by generous sharing of resources, use of its computerized program, and participation in a state-wide system. The large collection of the Academy of Medicine of Brooklyn offers thousands of volumes for the historian, both great works as highlights of medical achievements and more modest contributions of both early and recent date. The total library must serve as an intellectual resource, as well as a mechanism for the rapid transfer of current information. PMID:5644795

Even with rehydration, preservation in ethanol influences the mechanical properties of bone and how bone responds to experimental manipulation.

PubMed

Vesper, Evan O; Hammond, Max A; Allen, Matthew R; Wallace, Joseph M

2017-04-01

Typically, bones are harvested at the time of animal euthanasia and stored until mechanical testing. However, storage methods are not standardized, and differential effects on mechanical properties are possible between methods. The goal of this study was to investigate the effects that two common preservation methods (freezing wrapped in saline-soaked gauze and refrigerating ethanol fixed samples) have on bone mechanical properties in the context of an in vitro ribosylation treatment designed to modify mechanical integrity. It was hypothesized that there would be an interactive effect between ribose treatment and preservation method. Tibiae from twenty five 11week old female C57BL/6 mice were separated into 2 preservation groups. Micro-CT scans of contralateral pairs assessed differences in geometry prior to storage. After 7weeks of storage, bones in each pair of tibiae were soaked in a solution containing either 0M or 0.6M ribose for 1week prior to 4 point bending tests. There were no differences in any cortical geometric parameters between contralateral tibiae. There was a significant main effect of ethanol fixation on displacement to yield (-16.3%), stiffness (+24.5%), strain to yield (-13.9%), and elastic modulus (+18.5%) relative to frozen specimens. There was a significant main effect of ribose treatment for yield force (+13.9%), ultimate force (+9.2%), work to yield (+22.2%), yield stress (+14.1%), and resilience (+21.9%) relative to control-soaked bones. Postyield displacement, total displacement, postyield work, total work, total strain, and toughness were analyzed separately within each preservation method due to significant interactions. For samples stored frozen, all six properties were lower in the ribose-soaked group (49%-68%) while no significant effects of ribose were observed in ethanol fixed bones. Storage in ethanol likely caused changes to the collagen matrix which prevented or masked the embrittling effects of ribosylation that were seen in samples stored frozen wrapped in saline-soaked gauze. These data illustrate the clear importance of maintaining hydration if the eventual goal is to use bones for mechanical assessments and further show that storage in ethanol can alter potential to detect effects of experimental manipulation (in this case ribosylation). Copyright © 2017 Elsevier Inc. All rights reserved.

Abnormal Neural Network of Primary Insomnia: Evidence from Spatial Working Memory Task fMRI.

PubMed

Li, Yongli; Liu, Liya; Wang, Enfeng; Zhang, Hongju; Dou, Shewei; Tong, Li; Cheng, Jingliang; Chen, Chuanliang; Shi, Dapeng

2016-01-01

Contemporary functional MRI (fMRI) methods can provide a wealth of information about the neural mechanisms associated with primary insomnia (PI), which centrally involve neural network circuits related to spatial working memory. A total of 30 participants diagnosed with PI and without atypical brain anatomy were selected along with 30 age- and gender-matched healthy controls. Subjects were administered the Pittsburgh Sleep Quality Index (PSQI), Hamilton Rating Scale for Depression and clinical assessments of spatial working memory, followed by an MRI scan and fMRI in spatial memory task state. Statistically significant differences between PSQI and spatial working memory were observed between PI patients and controls (p < 0.01). Activation of neural networks related to spatial memory task state in the PI group was observed at the left temporal lobe, left occipital lobe and right frontal lobe. Lower levels of activation were observed in the left parahippocampal gyrus, right parahippocampal gyrus, bilateral temporal cortex, frontal cortex and superior parietal lobule. Participants with PI exhibited characteristic abnormalities in the neural network connectivity related to spatial working memory. These results may be indicative of an underlying pathological mechanism related to spatial working memory deterioration in PI, analogous to recently described mechanisms in other mental health disorders. © 2016 S. Karger AG, Basel.

Mechanical energy profiles of the combined ankle-foot system in normal gait: insights for prosthetic designs.

PubMed

Takahashi, Kota Z; Stanhope, Steven J

2013-09-01

Over the last half-century, the field of prosthetic engineering has continuously evolved with much attention being dedicated to restoring the mechanical energy properties of ankle joint musculatures during gait. However, the contributions of 'distal foot structures' (e.g., foot muscles, plantar soft tissue) have been overlooked. Therefore, the purpose of this study was to quantify the total mechanical energy profiles (e.g., power, work, and work-ratio) of the natural ankle-foot system (NAFS) by combining the contributions of the ankle joint and all distal foot structures during stance in level-ground steady state walking across various speeds (0.4, 0.6, 0.8 and 1.0 statures/s). The results from eleven healthy subjects walking barefoot indicated ankle joint and distal foot structures generally performed opposing roles: the ankle joint performed net positive work that systematically increased its energy generation with faster walking speeds, while the distal foot performed net negative work that systematically increased its energy absorption with faster walking speeds. Accounting for these simultaneous effects, the combined ankle-foot system exhibited increased work-ratios with faster walking. Most notably, the work-ratio was not significantly greater than 1.0 during the normal walking speed of 0.8 statures/s. Therefore, a prosthetic design that strategically exploits passive-dynamic properties (e.g., elastic energy storage and return) has the potential to replicate the mechanical energy profiles of the NAFS during level-ground steady-state walking. Copyright © 2013 Elsevier B.V. All rights reserved.

Reprobing the mechanism of negative thermal expansion in siliceous faujasite

DOE PAGES

Attfield, Martin P.; Feygenson, Mikhail; Neuefeind, Joerg C.; ...

2016-02-11

A combination of Rietveld refinement and PDF analysis of total neutron scattering data are used to provide further insight into the negative thermal expansion mechanism of siliceous faujasite. The negative thermal expansion mechanism of siliceous faujasite is attributed to the transverse vibrations of bridging oxygen atoms resulting in the coupled librations of the SiO 4 tetrahedra. The constituent SiO 4 tetrahedra are revealed to expand in size with temperature which is a behaviour that has not been determined directly previously and they are also shown to undergo some distortion as temperature is increased. However, these distortions are not distinct enoughmore » in any geometric manner for the average behaviour of the SiO 4 tetrahedra not to be considered as that of a rigid units. The work further displays the benefits of using total scattering experiments to unveil the finer details of dynamic thermomechanical processes within crystalline materials.« less

Thermogravimetric analysis for the determination of water release rate from microcrystalline cellulose dry powder and wet bead systems.

PubMed

Mayville, Francis C; Wigent, Rodney J; Schwartz, Joseph B

2006-01-01

The purpose of this work was to determine the total amount of water contained in dry powder and wet bead samples of microcrystalline cellulose, MCC, (Avicel PH-101), taken from various stages of the extrusion/marumerization process used to make beads and to determine the kinetic rates of water release from each sample. These samples were allowed to equilibrate in controlled humidity chambers at 25 degrees C. The total amount of water in each sample, after equilibration, was determined by thermogravimetric analysis (TGA) as a function of temperature. The rates of water release from these samples were determined by using isothermal gravimetric analysis (ITGA) as a function of time. Analysis of the results for these studies suggest that water was released from these systems by several different kinetic mechanisms. The water release mechanisms for these systems include: zero order, second order, and diffusion controlled kinetics. It is believed that all three kinetic mechanisms will occur at the same time, however; only one mechanism will be prominent. The prominent mechanism was based on the amount of water present in the sample.

Exploring structural properties of small carbon clusters Cn (n = 1, 2, 3) using molecular mechanics and energy minimization

NASA Astrophysics Data System (ADS)

Miswan, M. A.; Gopir, G.; Anas, M. M.

2016-11-01

Geometry optimization is one of the most widely used methods to study in carbon cluster Cn to understand its structural properties. The total energy for each of the structures was calculated using Octopus software with conjugate gradient Broyden-Fletcher-Goldfarb-Shanno (CG-BFGS). Our calculation and other studies indicate that the linear forms are the most stable structures. However, the C3 isomers have equal probability to form, as the differences in our calculation of total energy are statistically insignificant. Despite there are two cohort of total energy, the calculations are acceptable due to the energy ratio between C3 to C2 and C2 to C1 are comparable to others work. Meanwhile, the bond properties of the C2 and C3 bonds also gives significant difference between our work and previous study.

Metabolic and mechanical aspects of foot landing type, forefoot and rearfoot strike, in human running.

PubMed

Ardigò, L P; Lafortuna, C; Minetti, A E; Mognoni, P; Saibene, F

1995-09-01

The study was undertaken to assess the metabolic and the mechanical aspects of two different foot strike patterns in running, i.e. forefoot and rearfoot striking (FFS and RFS), and to understand whether there is some advantage for a runner to use one or the other of the two landing styles. Eight subjects performed two series of runs (FFS and RFS) on a treadmill at an average speed of 2.50, 2.78, 3.06, 3.33, 3.61, 3.89, 4.17 m s-1. Step frequency, oxygen uptake, mechanical work, and its two components, external and internal, were measured. No differences were found for step frequency, mechanical internal work per unit time and oxygen uptake, while external and total mechanical work per unit time were significantly higher, 7-12%, for FFS. The higher external work was the result of an increase of the work performed against both gravitational and inertial forces. As the energy expenditure was the same it has been speculated that a higher storage and release of energy takes place in the elastic structures of the lower leg with FFS. In a different series of experiments on six subjects contact time, time of deceleration and time of acceleration were measured by means of a video camera while running on the treadmill at 2.50, 3.33 and 4.17 m s-1, both FFS and RFS. Time of deceleration is similar for FFS and RFS, but contact time and time of acceleration are shorter, respectively 12 and 25%, for FFS.(ABSTRACT TRUNCATED AT 250 WORDS)

Thermostability analysis of line-tension-associated nucleation at a gas-liquid interface.

PubMed

Singha, Sanat Kumar; Das, Prasanta Kumar; Maiti, Biswajit

2017-01-01

The influence of line tension on the thermostability of a droplet nucleated from an oversaturated vapor at the interface of the vapor and another immiscible liquid is investigated. Along with the condition of mechanical equilibrium, the notion of extremization of the reversible work of formation is considered to obtain the critical parameters related to heterogeneous nucleation. From the energetic formulation, the critical reversible work of formation is found to be greater than that of homogeneous nucleation for high value of the positive line tension. On the other hand, for high value of the negative line tension, the critical reversible work of formation becomes negative. Therefore, these thermodynamic instabilities under certain substrate wettability situations necessitate a free-energetics-based stability of the nucleated droplet, because the system energy is not minimized under these conditions. This thermostability is analogous to the transition-based stability proposed by Widom [B. Widom, J. Phys. Chem. 99, 2803 (1995)]10.1021/j100009a041 in the case of partial wetting phenomena along with the positive line tension. The thermostability analysis limits the domain of the solution space of the present critical-value problem as the thermodynamic transformation in connection with homogeneous and workless nucleation is considered. Within the stability range of the geometry-based wetting parameters, three limiting modes of nucleation, i.e., total-dewetting-related homogeneous nucleation, and total-wetting-associated and total-submergence-associated workless nucleation scenarios, are identified. Either of the two related limiting wetting scenarios of workless nucleation, namely, total wetting and total submergence, is found to be favorable depending on the geometry-based wetting conditions. The line-tension-associated nucleation on a liquid surface can be differentiated from that on a rigid substrate, as in the former, the stability based on mechanical equilibrium and a typical case of workless nucleation with complete submergence are observed.

The mechanics of sprint running

PubMed Central

Cavagna, Giovanni A.; Komarek, L.; Mazzoleni, Stefania

1971-01-01

1. The effect of the velocity of shortening on the power developed by the muscles in sprint running was studied by measuring the mechanical work done to accelerate the body forward from the start to about 34 km/hr. 2. The work was measured at each step from the data obtained by means of a platform sensitive to the force impressed by the foot. 3. Almost the totality of the positive work done during the first second from the start is found as an increase of the kinetic energy of the body. However, as the speed of the run rises, air resistance and particularly the deceleration of the body forward, taking place at each step, rapidly increase, limiting the speed of the run. 4. The average power developed by the muscles during the push at each step increases with the velocity of running reaching 3-4 h.p. at the maximal speed attained. 5. At low speed the contractile component of the muscles seems to be mainly responsible for the power output, whereas at high speed (25-34 km/hr) an appreciable fraction of the power appears to be sustained by the mechanical energy stored in the `series elastic elements' during stretching the contracted muscles (negative work) and released immediately after in the positive work phase. ImagesFig. 1 PMID:5098087

Controlling the mechanical properties of carbon steel by thermomechanical treatment

NASA Astrophysics Data System (ADS)

Balavar, Mohsen; Mirzadeh, Hamed

2018-01-01

The effect of thermomechanical processing and heat treatment on the microstructure and mechanical properties of low carbon steel was studied. It was revealed that the dual phase ferritic-martensitic microstructure shows a good combination of tensile strength and ductility along with superior work hardening response. On the other hand, the bimodal-sized structure containing ultrafine grained (UFG) and micron-sized ferrite phase can be easily produced by cold rolling and annealing of the dual phase starting microstructure. This steel showed high yield stress, tensile strength, and ductility, but poor work hardening ability. The full annealed ferritic-pearlitic sheet with banded morphology exhibited low strength and high total elongation with the appearance of the yield point phenomenon. The martensitic steels, however, had high tensile strength and low ductility. By comparing the tensile properties of these steels, it was shown that it is possible to control the mechanical properties of low carbon steel by simple processing routes.

Output of skeletal muscle contractions. a study of isokinetic plantar flexion in athletes.

PubMed

Fugl-Meyer, A R; Mild, K H; Hörnsten, J

1982-06-01

Maximum torques, total work and mean power of isokinetic plantar flexions were measured with simultaneous registrations. The integrated electromyograms (iEMG) were obtained by surface electrodes from all three heads of the m. triceps surae. The method applied offers possibilities for adequate description of dynamic muscular work which in the case of plantar flexion in trained man declines as a negative exponential function of angular motion velocity. The decline is parallel to that of maximum torques. The summed triceps surae iEMG was inversely proportional to the velocity and direct proportional to time suggesting that structural rather than neural factors determine the relationships between velocity of angular motion and maximum torque/total work of single Mmaneuvers. Moreover, the fact that maximum mean power as well as maximum electrical efficiency were reached at the functional velocity of toe-off during gait suggests an influence of pragmatic demands on plantar flexion mechanical output.

Chrysotile asbestos exposure associated with removal of automobile exhaust systems (ca. 1945-1975) by mechanics: results of a simulation study.

PubMed

Paustenbach, Dennis J; Madl, Amy K; Donovan, Ellen; Clark, Katherine; Fehling, Kurt; Lee, Terry C

2006-03-01

For decades, asbestos-containing gaskets were used in virtually every system that involved the transport of fluids or gases. Prior to the mid-1970s, some automobile exhaust systems contained asbestos gaskets either at flanges along the exhaust pipes or at the exhaust manifolds of the engine. A limited number of automobile mufflers were lined with asbestos paper. This paper describes a simulation study that characterized personal and bystander exposures to asbestos during the removal of automobile exhaust systems (ca. 1945-1975) containing asbestos gaskets. A total of 16 pre-1974 vehicles with old or original exhaust systems were studied. Of the 16 vehicles, 12 contained asbestos gaskets in the exhaust system and two vehicles had asbestos lining inside the muffler. A total of 82 samples (23 personal, 38 bystander, and 21 indoor background) were analyzed by Phase Contrast Microscopy (PCM) and 88 samples (25 personal, 41 bystander, and 22 indoor background) by Transmission Electron Microscopy (TEM). Only seven of 25 worker samples analyzed by TEM detected asbestos fibers and 18 were below the analytical sensitivity limit (mean 0.013 f/cc, range 0.001-0.074 f/cc). Applying the ratio of asbestos fibers:total fibers (including non-asbestos) as determined by TEM to the PCM results showed an average (1 h) adjusted PCM worker exposure of 0.018 f/cc (0.002-0.04 f/cc). The average (1 h) adjusted PCM airborne concentration for bystanders was 0.008 f/cc (range 0.0008-0.015 f/cc). Assuming a mechanic can replace four automobile single exhaust systems in 1 workday, the estimated 8-h time-weighted average (TWA) for a mechanic performing this work was 0.01 f/cc. Under a scenario where a mechanic might repeatedly conduct exhaust work, these results suggest that exposures to asbestos from work with automobile exhaust systems during the 1950s through the 1970s containing asbestos gaskets were substantially below 0.1 f/cc, the current PEL for chrysotile asbestos, and quite often were not detectable.

Development of a database for chemical mechanism assignments for volatile organic emissions.

PubMed

Carter, William P L

2015-10-01

The development of a database for making model species assignments when preparing total organic gas (TOG) emissions input for atmospheric models is described. This database currently has assignments of model species for 12 different gas-phase chemical mechanisms for over 1700 chemical compounds and covers over 3000 chemical categories used in five different anthropogenic TOG profile databases or output by two different biogenic emissions models. This involved developing a unified chemical classification system, assigning compounds to mixtures, assigning model species for the mechanisms to the compounds, and making assignments for unknown, unassigned, and nonvolatile mass. The comprehensiveness of the assignments, the contributions of various types of speciation categories to current profile and total emissions data, inconsistencies with existing undocumented model species assignments, and remaining speciation issues and areas of needed work are also discussed. The use of the system to prepare input for SMOKE, the Speciation Tool, and for biogenic models is described in the supplementary materials. The database, associated programs and files, and a users manual are available online at http://www.cert.ucr.edu/~carter/emitdb . Assigning air quality model species to the hundreds of emitted chemicals is a necessary link between emissions data and modeling effects of emissions on air quality. This is not easy and makes it difficult to implement new and more chemically detailed mechanisms in models. If done incorrectly, it is similar to errors in emissions speciation or the chemical mechanism used. Nevertheless, making such assignments is often an afterthought in chemical mechanism development and emissions processing, and existing assignments are usually undocumented and have errors and inconsistencies. This work is designed to address some of these problems.

[Physiological mechanisms of the etiology of visual fatigue during work involving visual stress].

PubMed

Korniushina, T A

2000-01-01

Physiological parameters of vision were studied in three professional groups (a total of 1204 subjects): microscope operators, subjects working with magnifying glasses, and computer users. General and specific features of visual system fatigue formation were identified. Because of complete (in microscope operators) or partial (in subjects working with magnifying glasses and display users) "deprivation" of accommodation, these subjects develop early presbyopia (at the age of 30-35 years). In microscope operators long strain of accommodation system leads to professional myopia, while display users develop pseudomyopia. The highest overstrain is observed after 4 years of work in microscope operators, after 5 years in magnifying glass users, and after 6 years in computer users.

Issues of intergranular embrittlement of VVER-type nuclear reactors pressure vessel materials

NASA Astrophysics Data System (ADS)

Zabusov, O.

2016-04-01

In light of worldwide tendency to extension of service life of operating nuclear power plants - VVER-type in the first place - recently a special attention is concentrated on phenomena taking place in reactor pressure vessel materials that are able to lead to increased level of mechanical characteristics degradation (resistibility to brittle fracture) during long term of operation. Formerly the hardening mechanism of degradation (increase in the yield strength under influence of irradiation) mainly had been taken into consideration to assess pressure vessel service life limitations, but when extending the service life up to 60 years and more the non-hardening mechanism (intergranular embrittlement of the steels) must be taken into account as well. In this connection NRC “Kurchatov Institute” has initiated a number of works on investigations of this mechanism contribution to the total embrittlement of reactor pressure vessel steels. The main results of these investigations are described in this article. Results of grain boundary phosphorus concentration measurements in specimens made of first generation of VVER-type pressure vessels materials as well as VVER-1000 surveillance specimens are presented. An assessment of non-hardening mechanism contribution to the total ductile-to- brittle transition temperature shift is given.

The effect of heavy work on the musculoskeletal system of dockers.

PubMed

Waśkiewicz, J

1996-01-01

In compass of 1989-1995 all in all 388 dockers were examined, including 136 stevedores, 128 operators of mechanic equipment, 74 hoistmen and 73 retired stevedores. Out of the group of 508 stevedores that in 1989 was selected for the purpose of the study, at the end of 1995 there were 136 still working, and out of 141 operators 128 remained in employment. The number of the hoistmen working did not change. The stevedores perform heavy and a very heavy loading labour, the rest moderate and light. The highest number of changes was found in the lumbar segment of the spine-totally 56.2%, then in the sacroiliac articulations-totally 50.6%, in the cervical spine-totally 34.4%, within the shoulder girdle-33.1% and in the thoracic segment of the spine-26.3%. In stevedores these proportions were higher. A transfer to a lighter work or retirement could not inhibit the degenerative process within the musculoskeletal system. Evaluating the development of the disease in the period of observation, a progress of the pathological process was observed. No relation between the loss of fitness in stevedores and their body mass could be found. The mean time of the disease tended to increase with age of the examined. In a considerable number of the subjects a casual connection between the changes in the musculoskeletal system and the work performed was revealed.

Lower extremity work is associated with club head velocity during the golf swing in experienced golfers.

PubMed

McNally, M P; Yontz, N; Chaudhari, A M

2014-08-01

While the golf swing is a complex whole body movement requiring coordination of all joints to achieve maximum ball velocity, the kinetic contribution of the lower extremities to club head velocity has not been quantified, despite the perception that the legs are a primary source of power during the swing. Mechanical power at the hips, knees, and ankles was estimated during the downswing phase of a full swing with a driver using a passive optical motion capture system and 2 force plates for adult males across a range of age and self-reported skill levels. Total work by the lower extremities was calculated by integrating the powers of all 6 joints over the downswing. Regression analyses showed that total lower extremity work was a strong predictor of club head velocity (R=0.63). Secondary analyses showed different relationships to club head velocity in lead and trail leg lower extremity joints, but none of these were as predictive of club head velocity as the total work performed by the lower extremities. These results provide quantitative evidence that the lower body's kinetic contribution may be an important factor in achieving greater club head velocity, contributing to greater driving distance and overall golf performance. © Georg Thieme Verlag KG Stuttgart · New York.

[Night work, shift work: Breast cancer risk factor?].

PubMed

Benabu, J-C; Stoll, F; Gonzalez, M; Mathelin, C

2015-12-01

The aim of this review was to determine the link between night/shift work and breast cancer. The analysed articles were taken from the PUBMED database between 1996 and 2015. The keywords used were "breast cancer risk", "night work" and "shift work". In total, 25 articles were selected. Night/shift workers are more at risk to develop a breast cancer (relative risk (RR) between 1.09; 95% CI: 1.02-1.20 and 1.48; 95% CI: 1.36-1.61 in the meta-analyses). However, this risk is not found by some cohort and case-control studies. The circadian rhythm disruption, responsible of disorderliness of melatonin secretion, could be one of the mechanisms involved in the increase of that risk. Hormonal status of night/shift workers, their geographic origin, their lifestyle and their vitamin D deficiency appear as other mechanisms potentially responsible for increased risk of cancer in this professional population. Moreover, a dose-effect connection may exist, with an increase of the risk with the number of years of night/shift work. Night/shift work is associated with a moderate increased risk of breast cancer, especially among women who worked over 20 years. Recommendations concerning the breast monitoring in this population could be diffused. The benefit of melatonin supplementation remains to be assessed. Copyright © 2015. Published by Elsevier SAS.

Short term total sleep deprivation in the rat increases antioxidant responses in multiple brain regions without impairing spontaneous alternation behavior

PubMed Central

Ramanathan, Lalini; Hu, Shuxin; Frautschy, Sally A.; Siegel, Jerome M.

2009-01-01

Total sleep deprivation (TSD) induces a broad spectrum of cognitive, behavioral and cellular changes. We previously reported that long term (5–11 days) TSD in the rat, by the disk-over-water method, decreases the activity of the antioxidant enzyme superoxide dismutase (SOD) in the brainstem and hippocampus. To gain insight into the mechanisms causing cognitive impairment, here we explore the early associations between metabolic activity, antioxidant responses and working memory (one form of cognitive impairment). Specifically we investigated the impact of short term (6 h) TSD, by gentle handling, on the levels of the endogenous antioxidant, total glutathione (GSHt), and the activities of the antioxidative enzymes, SOD and glutathione peroxidase (GPx). Short term TSD had no significant impact on SOD activity, but increased GSHt levels in the rat cortex, brainstem and basal forebrain, and GPx activity in the rat hippocampus and cerebellum. We also observed increased activity of hexokinase, (HK), the rate limiting enzyme of glucose metabolism, in the rat cortex and hypothalamus. We further showed that 6h of TSD leads to increased exploratory behavior to a new environment, without impairing spontaneous alternation behavior (SAB) in the Y maze. We conclude that acute (6h) sleep loss may trigger compensatory mechanisms (like increased antioxidant responses) that prevent initial deterioration in working memory. PMID:19850085

A new infant hybrid respiratory simulator: preliminary evaluation based on clinical data.

PubMed

Stankiewicz, Barbara; Pałko, Krzysztof J; Darowski, Marek; Zieliński, Krzysztof; Kozarski, Maciej

2017-11-01

A new hybrid (numerical-physical) simulator of the respiratory system, designed to simulate spontaneous and artificial/assisted ventilation of preterm and full-term infants underwent preliminary evaluation. A numerical, seven-compartmental model of the respiratory system mechanics allows the operator to simulate global and peripheral obstruction and restriction of the lungs. The physical part of the simulator is a piston-based construction of impedance transformer. LabVIEW real-time software coordinates the work of both parts of the simulator and its interaction with a ventilator. Using clinical data, five groups of "artificial infants" were examined: healthy full-term infants, very low-birth-weight preterm infants successfully (VLBW) and unsuccessfully extubated (VLBWun) and extremely low-birth-weight preterm infants without (ELBW) and with bronchopulmonary dysplasia (ELBW_BPD). Pressure-controlled ventilation was simulated to measure peak inspiratory pressure, mean airway pressure, total (patient + endotracheal tube) airway resistance (R), total dynamic compliance of the respiratory system (C), and total work of breathing by the ventilator (WOB). The differences between simulation and clinical parameters were not significant. High correlation coefficients between both types of data were obtained for R, C, and WOB (γ R  = 0.99, P < 0.0005; γ C  = 0.85, P < 0.005; γ WOB  = 0.96, P < 0.05, respectively). Thus, the simulator accurately reproduces infant respiratory system mechanics.

Math anxiety and math performance in children: The mediating roles of working memory and math self-concept.

PubMed

Justicia-Galiano, M José; Martín-Puga, M Eva; Linares, Rocío; Pelegrina, Santiago

2017-12-01

Numerous studies, most of them involving adolescents and adults, have evidenced a moderate negative relationship between math anxiety and math performance. There are, however, a limited number of studies that have addressed the mechanisms underlying this relation. This study aimed to investigate the role of two possible mediational mechanisms between math anxiety and math performance. Specifically, we sought to test the simultaneous mediating role of working memory and math self-concept. A total of 167 children aged 8-12 years participated in this study. Children completed a set of questionnaires used to assess math and trait anxiety, math self-concept as well as measures of math fluency and math problem-solving. Teachers were asked to rate each student's math achievement. As measures of working memory, two backward span tasks were administered to the children. A series of multiple mediation analyses were conducted. Results indicated that both mediators (working memory and math self-concept) contributed to explaining the relationship between math anxiety and math achievement. Results suggest that working memory and self-concept could be worth considering when designing interventions aimed at helping students with math anxiety. Longitudinal designs could also be used to better understand the mediational mechanisms that may explain the relationship between math anxiety and math performance. © 2017 The British Psychological Society.

Inkjet Printing in Liquid Environments.

PubMed

Zhang, Yanzhen; Li, Dege; Liu, Yonghong; Wittstock, Gunther

2018-05-28

Inkjet printing (IJP) is an old but still vivifying technique for flexible and cost-effective printing of various kinds of functional inks. Normally, IJP can only work in gaseous environments. Here, it is shown that traditional piezoelectric IJP can be performed in liquid environments with a totally different droplet dispensing and manipulating mechanism. With the same piezoelectric nozzle, the volume of the droplets printed in a carrier liquid can be thousands of times smaller than those printed in air. Therefore, this work demonstrates a working mode of traditional IJP with a highly improved resolution opening possibilities for novel applications of the IJP technique. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Muscles do more positive than negative work in human locomotion

PubMed Central

DeVita, Paul; Helseth, Joseph; Hortobagyi, Tibor

2008-01-01

Summary Muscle work during level walking and ascent and descent ramp and stairway walking was assessed in order to explore the proposition that muscles perform more positive than negative work during these locomotion tasks. Thirty four healthy human adults were tested while maintaining a constant average walking velocity in the five gait conditions. Ground reaction force and sagittal plane kinematic data were obtained during the stance phases of these gaits and used in inverse dynamic analyses to calculate joint torques and powers at the hip, knee and ankle. Muscle work was derived as the area under the joint power vs time curves and was partitioned into positive, negative and net components. Dependent t-tests were used to compare positive and negative work in level walking and net joint work between ascent and descent gaits on the ramp and stairs (P<0.010). Total negative and positive work in level walking was −34 J and 50 J, respectively, with the difference in magnitude being statistically significant (P<0.001). Level walking was therefore performed with 16 J of net positive muscle work per step. The magnitude of the net work in ramp ascent was 25% greater than the magnitude of net work in ramp descent (89 vs −71 J m−1, P<0.010). Similarly, the magnitude of the net work in stair ascent was 43% greater than the magnitude of net work in stair descent (107 vs −75 J step−1, P<0.000). We identified three potential causes for the reduced negative vs positive work in these locomotion tasks: (1) the larger magnitude of the accelerations induced by the larger ground reaction forces in descending compared to ascending gaits elicited greater energy dissipation in non-muscular tissues, (2) the ground reaction force vector was directed closer to the joint centers in ramp and stair descent compared to ascent, which reduced the load on the muscular tissues and their energy dissipating response, and (3) despite the need to produce negative muscle work in descending gaits, both ramp and stair descent also had positive muscle work to propel the lower extremity upward and forward into the swing phase movement trajectory. We used these data to formulate two novel hypotheses about human locomotion. First, level walking requires muscles to generate a net positive amount of work per gait cycle to overcome energy losses by other tissues. Second, skeletal muscles generate more mechanical energy in gait tasks that raise the center of mass compared to the mechanical energy they dissipate in gait tasks that lower the center of mass, despite equivalent changes in total mechanical energy. PMID:17872990

Muscles do more positive than negative work in human locomotion.

PubMed

DeVita, Paul; Helseth, Joseph; Hortobagyi, Tibor

2007-10-01

Muscle work during level walking and ascent and descent ramp and stairway walking was assessed in order to explore the proposition that muscles perform more positive than negative work during these locomotion tasks. Thirty four healthy human adults were tested while maintaining a constant average walking velocity in the five gait conditions. Ground reaction force and sagittal plane kinematic data were obtained during the stance phases of these gaits and used in inverse dynamic analyses to calculate joint torques and powers at the hip, knee and ankle. Muscle work was derived as the area under the joint power vs time curves and was partitioned into positive, negative and net components. Dependent t-tests were used to compare positive and negative work in level walking and net joint work between ascent and descent gaits on the ramp and stairs (P<0.010). Total negative and positive work in level walking was -34 J and 50 J, respectively, with the difference in magnitude being statistically significant (P<0.001). Level walking was therefore performed with 16 J of net positive muscle work per step. The magnitude of the net work in ramp ascent was 25% greater than the magnitude of net work in ramp descent (89 vs -71 J m(-1), P<0.010). Similarly, the magnitude of the net work in stair ascent was 43% greater than the magnitude of net work in stair descent (107 vs -75 J step(-1), P<0.000). We identified three potential causes for the reduced negative vs positive work in these locomotion tasks: (1) the larger magnitude of the accelerations induced by the larger ground reaction forces in descending compared to ascending gaits elicited greater energy dissipation in non-muscular tissues, (2) the ground reaction force vector was directed closer to the joint centers in ramp and stair descent compared to ascent, which reduced the load on the muscular tissues and their energy dissipating response, and (3) despite the need to produce negative muscle work in descending gaits, both ramp and stair descent also had positive muscle work to propel the lower extremity upward and forward into the swing phase movement trajectory. We used these data to formulate two novel hypotheses about human locomotion. First, level walking requires muscles to generate a net positive amount of work per gait cycle to overcome energy losses by other tissues. Second, skeletal muscles generate more mechanical energy in gait tasks that raise the center of mass compared to the mechanical energy they dissipate in gait tasks that lower the center of mass, despite equivalent changes in total mechanical energy.

Modeling subduction earthquake sources in the central-western region of Colombia using waveform inversion of body waves

NASA Astrophysics Data System (ADS)

Monsalve-Jaramillo, Hugo; Valencia-Mina, William; Cano-Saldaña, Leonardo; Vargas, Carlos A.

2018-05-01

Source parameters of four earthquakes located within the Wadati-Benioff zone of the Nazca plate subducting beneath the South American plate in Colombia were determined. The seismic moments for these events were recalculated and their approximate equivalent rupture area, slip distribution and stress drop were estimated. The source parameters for these earthquakes were obtained by deconvolving multiple events through teleseismic analysis of body waves recorded in long period stations and with simultaneous inversion of P and SH waves. The calculated source time functions for these events showed different stages that suggest that these earthquakes can reasonably be thought of being composed of two subevents. Even though two of the overall focal mechanisms obtained yielded similar results to those reported by the CMT catalogue, the two other mechanisms showed a clear difference compared to those officially reported. Despite this, it appropriate to mention that the mechanisms inverted in this work agree well with the expected orientation of faulting at that depth as well as with the wave forms they are expected to produce. In some of the solutions achieved, one of the two subevents exhibited a focal mechanism considerably different from the total earthquake mechanism; this could be interpreted as the result of a slight deviation from the overall motion due the complex stress field as well as the possibility of a combination of different sources of energy release analogous to the ones that may occur in deeper earthquakes. In those cases, the subevents with very different focal mechanism compared to the total earthquake mechanism had little contribution to the final solution and thus little contribution to the total amount of energy released.

Thermodynamic and Mechanical Analysis of a Thermomagnetic Rotary Engine

NASA Astrophysics Data System (ADS)

Fajar, D. M.; Khotimah, S. N.; Khairurrijal

2016-08-01

A heat engine in magnetic system had three thermodynamic coordinates: magnetic intensity ℋ, total magnetization ℳ, and temperature T, where the first two of them are respectively analogous to that of gaseous system: pressure P and volume V. Consequently, Carnot cycle that constitutes the principle of a heat engine in gaseous system is also valid on that in magnetic system. A thermomagnetic rotary engine is one model of it that was designed in the form of a ferromagnetic wheel that can rotates because of magnetization change at Curie temperature. The study is aimed to describe the thermodynamic and mechanical analysis of a thermomagnetic rotary engine and calculate the efficiencies. In thermodynamic view, the ideal processes are isothermal demagnetization, adiabatic demagnetization, isothermal magnetization, and adiabatic magnetization. The values of thermodynamic efficiency depend on temperature difference between hot and cold reservoir. In mechanical view, a rotational work is determined through calculation of moment of inertia and average angular speed. The value of mechanical efficiency is calculated from ratio between rotational work and heat received by system. The study also obtains exergetic efficiency that states the performance quality of the engine.

A Measure of Total Research Impact Independent of Time and Discipline

PubMed Central

Pepe, Alberto; Kurtz, Michael J.

2012-01-01

Authorship and citation practices evolve with time and differ by academic discipline. As such, indicators of research productivity based on citation records are naturally subject to historical and disciplinary effects. We observe these effects on a corpus of astronomer career data constructed from a database of refereed publications. We employ a simple mechanism to measure research output using author and reference counts available in bibliographic databases to develop a citation-based indicator of research productivity. The total research impact (tori) quantifies, for an individual, the total amount of scholarly work that others have devoted to his/her work, measured in the volume of research papers. A derived measure, the research impact quotient (riq), is an age-independent measure of an individual's research ability. We demonstrate that these measures are substantially less vulnerable to temporal debasement and cross-disciplinary bias than the most popular current measures. The proposed measures of research impact, tori and riq, have been implemented in the Smithsonian/NASA Astrophysics Data System. PMID:23144782

Does office space occupation matter? The role of the number of persons per enclosed office space, psychosocial work characteristics, and environmental satisfaction in the physical and mental health of employees.

PubMed

Herbig, B; Schneider, A; Nowak, D

2016-10-01

The study examined the effects of office space occupation, psychosocial work characteristics, and environmental satisfaction on physical and mental health of office workers in small-sized and open-plan offices as well as possible underlying mechanisms. Office space occupation was characterized as number of persons per one enclosed office space. A total of 207 office employees with similar jobs in offices with different space occupation were surveyed regarding their work situation (psychosocial work characteristics, satisfaction with privacy, acoustics, and control) and health (psychosomatic complaints, irritation, mental well-being, and work ability). Binary logistic and linear regression analyses as well as bootstrapped mediation analyses were used to determine associations and underlying mechanisms. Employee health was significantly associated with all work characteristics. Psychosocial work stressors had the strongest relation to physical and mental health (OR range: 1.66-3.72). The effect of office space occupation on employee health was mediated by stressors and environmental satisfaction, but not by psychosocial work resources. As assumed by sociotechnical approaches, a higher number of persons per enclosed office space was associated with adverse health effects. However, the strongest associations were found with psychosocial work stressors. When revising office design, a holistic approach to work (re)design is needed. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Interlimb relation during the double support phase of gait: an electromyographic, mechanical and energy-based analysis.

PubMed

Sousa, Andreia S P; Silva, Augusta; Tavares, João Manuel R S

2013-03-01

The purpose of this study is to analyse the interlimb relation and the influence of mechanical energy on metabolic energy expenditure during gait. In total, 22 subjects were monitored as to electromyographic activity, ground reaction forces and VO2 consumption (metabolic power) during gait. The results demonstrate a moderate negative correlation between the activity of tibialis anterior, biceps femoris and vastus medialis of the trailing limb during the transition between mid-stance and double support and that of the leading limb during double support for the same muscles, and between these and gastrocnemius medialis and soleus of the trailing limb during double support. Trailing limb soleus during the transition between mid-stance and double support was positively correlated to leading limb tibialis anterior, vastus medialis and biceps femoris during double support. Also, the trailing limb centre of mass mechanical work was strongly influenced by the leading limbs, although only the mechanical power related to forward progression of both limbs was correlated to metabolic power. These findings demonstrate a consistent interlimb relation in terms of electromyographic activity and centre of mass mechanical work, being the relations occurred in the plane of forward progression the more important to gait energy expenditure.

Productivity cost calculations in health economic evaluations: correcting for compensation mechanisms and multiplier effects.

PubMed

Krol, Marieke; Brouwer, Werner B F; Severens, Johan L; Kaper, Janneke; Evers, Silvia M A A

2012-12-01

Productivity costs related to paid work are commonly calculated in economic evaluations of health technologies by multiplying the relevant number of work days lost with a wage rate estimate. It has been argued that actual productivity costs may either be lower or higher than current estimates due to compensation mechanisms and/or multiplier effects (related to team dependency and problems with finding good substitutes in cases of absenteeism). Empirical evidence on such mechanisms and their impact on productivity costs is scarce, however. This study aims to increase knowledge on how diminished productivity is compensated within firms. Moreover, it aims to explore how compensation and multiplier effects potentially affect productivity cost estimates. Absenteeism and compensation mechanisms were measured in a randomized trial among Dutch citizens examining the cost-effectiveness of reimbursement for smoking cessation treatment. Multiplier effects were extracted from published literature. Productivity costs were calculated applying the Friction Cost Approach. Regular estimates were subsequently adjusted for (i) compensation during regular working hours, (ii) job dependent multipliers and (iii) both compensation and multiplier effects. A total of 187 respondents included in the trial were useful for inclusion in this study, based on being in paid employment, having experienced absenteeism in the preceding six months and completing the questionnaire on absenteeism and compensation mechanisms. Over half of these respondents stated that their absenteeism was compensated during normal working hours by themselves or colleagues. Only counting productivity costs not compensated in regular working hours reduced the traditional estimate by 57%. Correcting for multiplier effects increased regular estimates by a quarter. Combining both impacts decreased traditional estimates by 29%. To conclude, large amounts of lost production are compensated in normal hours. Productivity costs estimates are strongly influenced by adjustment for compensation mechanisms and multiplier effects. The validity of such adjustments needs further examination, however. Copyright © 2012 Elsevier Ltd. All rights reserved.

How Work Organization Affects the Prevalence of WMSDs: A Case-control Study.

PubMed

Liu, Lu; Chen, Song Gen; Tang, Shi Chuan; Wang, Sheng; He, Li Hua; Guo, Ze Hua; Li, Jing Yun; Yu, Shan Fa; Wang, Zhong Xu

2015-09-01

In this study, we aimed at exploring the association between work-related musculoskeletal disorders (WMSDs) and work organization based on a case-control study. A total of 1938 workers who claimed to suffer from WMSDs were selected from Beijing, Henan, Hubei, and the Guangdong province. The control group consisted of 2009 workers employed in similar industries without severe disease or musculoskeletal discomforts. We used a modified version of the questionnaire developed by the NMQ and the DMQ to investigate individual and work-related factors. A total of 13 variables (P<0.1) were selected by the chi-square test and finally, 7 variables entered into the equation, with 6 variables reaching statistical significance (P<0.05). The odds ratios (OR) of 'work changing with season' and 'sufficient rest time' did not reach 1 (0.749 and 0.441, respectively). In addition, 'sufficient rest time' seemed to be the stronger protective factor according to its higher standardized coefficient. And 'repetitive work every minute', 'constantly repetitive work' (every day), 'shortage of site personnel', and 'often switching shifts with others' seemed to be the risk factors. Work organization may have comprehensive effects on the occurrence of WMSDs. This pattern of associations suggests that further investigation into the mechanism of how work organization affects the prevalence of WMSDs is required. Copyright © 2015 The Editorial Board of Biomedical and Environmental Sciences. Published by China CDC. All rights reserved.

ON THE BIOMECHANICS OF HEART VALVE FUNCTION

PubMed Central

Sacks, Michael S.; Merryman, W. David; Schmidt, David E.

2009-01-01

Heart valves (HVs) are fluidic control components of the heart that ensure unidirectional blood flow during the cardiac cycle. However, this description does not adequately describe the biomechanical ramifications of their function in that their mechanics are multi-modal. Moreover, they must replicate their cyclic function over an entire lifetime, with an estimated total functional demand of least 3×109 cycles. The focus of the present review is on the functional biomechanics of heart valves. Thus, the focus of the present review is on functional biomechanics, referring primarily to biosolid as well as several key biofluid mechanical aspects underlying heart valve physiological function. Specifically, we refer to the mechanical behaviors of the extra-cellular matrix structural proteins, underlying cellular function, and their integrated relation to the major aspects of valvular hemodynamic function. While we focus on the work from the author’s laboratories, relevant works of other investigators have been included whenever appropriate. We conclude with a summary of important future trends. PMID:19540499

Verbal Short-Term Memory in Individuals with Congenital Articulatory Disorders: New Empirical Data and Review of the Literature

ERIC Educational Resources Information Center

Carlesimo, G. A.; Galloni, F.; Bonanni, R.; Sabbadini, M.

2006-01-01

Background: To investigate the nature of the articulatory rehearsal mechanism of the Articulatory Loop in Baddeley's Working Memory model, it seems particularly important to study individuals who developed a deficit (dysarthria) or total abolition (anarthria) of the ability to articulate language following a cerebral lesion. Method: In this study,…

RNA sequencing to determine the contribution of kinase receptor transactivation to G protein coupled receptor signalling in vascular smooth muscle cells.

PubMed

Kamato, Danielle; Bhaskarala, Venkata Vijayanand; Mantri, Nitin; Oh, Tae Gyu; Ling, Dora; Janke, Reearna; Zheng, Wenhua; Little, Peter J; Osman, Narin

2017-01-01

G protein coupled receptor (GPCR) signalling covers three major mechanisms. GPCR agonist engagement allows for the G proteins to bind to the receptor leading to a classical downstream signalling cascade. The second mechanism is via the utilization of the β-arrestin signalling molecule and thirdly via transactivation dependent signalling. GPCRs can transactivate protein tyrosine kinase receptors (PTKR) to activate respective downstream signalling intermediates. In the past decade GPCR transactivation dependent signalling was expanded to show transactivation of serine/threonine kinase receptors (S/TKR). Kinase receptor transactivation enormously broadens the GPCR signalling paradigm. This work utilizes next generation RNA-sequencing to study the contribution of transactivation dependent signalling to total protease activated receptor (PAR)-1 signalling. Transactivation, assessed as gene expression, accounted for 50 percent of the total genes regulated by thrombin acting through PAR-1 in human coronary artery smooth muscle cells. GPCR transactivation of PTKRs is approximately equally important as the transactivation of the S/TKR with 209 and 177 genes regulated respectively, via either signalling pathway. This work shows that genome wide studies can provide powerful insights into GPCR mediated signalling pathways.

"It's Totally Destroyed Our Life": Exploring the Pathways and Mechanisms Between Precarious Employment and Health and Well-being Among Immigrant Men and Women in Toronto.

PubMed

Premji, Stephanie

2018-01-01

Precarious employment is rapidly growing, but qualitative data on pathways to and mechanisms for health and well-being is lacking. This article describes the cumulative and intersecting micro-level pathways and mechanisms between precarious employment and health among immigrant men and women in Toronto. It draws on semi-structured interviews conducted in 2014 with 15 women and 12 men from 11 countries of origin. The article describes how precarious employment, conceptualized by workers as encompassing powerlessness, economic insecurity, work for multiple employers, nonstandard and unpredictable schedules, hazardous working conditions, and lack of benefits and protections, negatively impacts workers' physical and mental health as well as that of their spouses or partners and children. It documents pathways to health and well-being, including stress, material and social deprivation, and exposure to hazards, as well as commuting difficulties and childcare challenges. Throughout, gender and migration are shown to influence experiences of work and health. The findings draw attention to dimensions of precarity and pathways to health that are not always highlighted in research and discourse on precarious employment and provide valuable insights into the vicious circle of precarious employment and health.

Interrelation of changes in the total content of ozone in the northern hemisphere with the velocity of the stratosphere circumpolar vortex

NASA Astrophysics Data System (ADS)

Kolyada, Maria N.; Kashkin, Valentin B.

2004-12-01

Considering the high significance of the ozone for preservation and maintenance of the biosphere and the temperature balance of the atmosphere the investigation of the ozone layer is a very important part of the investigation of the planet"s atmosphere. In this work results of investigations of TOC variability in the Northern Hemisphere and the influence of variability of the circumpolar vortex rotation velocity on the ozone layer are presented. Mean values of total ozone concentration in the Northern Hemisphere (by satellite data) and rotation velocities of the circumpolar vortex are calculated for each month from February to April during 1998-2004. Also in this work the mechanism of the influence of the natural factors on TOC variability solar activity during the spring is suggested.

Cations Modulate Actin Bundle Mechanics, Assembly Dynamics, and Structure.

PubMed

Castaneda, Nicholas; Zheng, Tianyu; Rivera-Jacquez, Hector J; Lee, Hyun-Ju; Hyun, Jaekyung; Balaeff, Alexander; Huo, Qun; Kang, Hyeran

2018-04-12

Actin bundles are key factors in the mechanical support and dynamic reorganization of the cytoskeleton. High concentrations of multivalent counterions promote bundle formation through electrostatic attraction between actin filaments that are negatively charged polyelectrolytes. In this study, we evaluate how physiologically relevant divalent cations affect the mechanical, dynamic, and structural properties of actin bundles. Using a combination of total internal reflection fluorescence microscopy, transmission electron microscopy, and dynamic light scattering, we demonstrate that divalent cations modulate bundle stiffness, length distribution, and lateral growth. Molecular dynamics simulations of an all-atom model of the actin bundle reveal specific actin residues coordinate cation-binding sites that promote the bundle formation. Our work suggests that specific cation interactions may play a fundamental role in the assembly, structure, and mechanical properties of actin bundles.

Boron Nitride Coated Carbon Nanotube Arrays with Enhanced Compressive Mechanical Property

NASA Astrophysics Data System (ADS)

Jing, Lin; Tay, Roland Yingjie; Li, Hongling; Tsang, Siu Hon; Tan, Dunlin; Zhang, Bowei; Tok, Alfred Iing Yoong; Teo, Edwin Hang Tong

Vertically aligned carbon nanotube (CNT) array is one of the most promising energy dissipating materials due to its excellent temperature invariant mechanical property. However, the CNT arrays with desirable recoverability after compression is still a challenge. Here, we report on the mechanical enhancement of the CNT arrays reinforced by coating with boron nitride (BN) layers. These BN coated CNT (BN/CNT) arrays exhibit excellent compressive strength and recoverability as compared to those of the as-prepared CNT arrays which totally collapsed after compression. In addition, the BN coating also provides better resistance to oxidation due to its intrinsic thermal stability. This work presented here opens a new pathway towards tuning mechanical behavior of any arbitrary CNT arrays for promising potential such as damper, vibration isolator and shock absorber applications.

The maximum work principle regarded as a consequence of an optimization problem based on mechanical virtual power principle and application of constructal theory

NASA Astrophysics Data System (ADS)

Gavrus, Adinel

2017-10-01

This scientific paper proposes to prove that the maximum work principle used by theory of continuum media plasticity can be regarded as a consequence of an optimization problem based on constructal theory (prof. Adrian BEJAN). It is known that the thermodynamics define the conservation of energy and the irreversibility of natural systems evolution. From mechanical point of view the first one permits to define the momentum balance equation, respectively the virtual power principle while the second one explains the tendency of all currents to flow from high to low values. According to the constructal law all finite-size system searches to evolve in such configurations that flow more and more easily over time distributing the imperfections in order to maximize entropy and to minimize the losses or dissipations. During a material forming process the application of constructal theory principles leads to the conclusion that under external loads the material flow is that which all dissipated mechanical power (deformation and friction) become minimal. On a mechanical point of view it is then possible to formulate the real state of all mechanical variables (stress, strain, strain rate) as those that minimize the total dissipated power. So between all other virtual non-equilibrium states, the real state minimizes the total dissipated power. It can be then obtained a variational minimization problem and this paper proof in a mathematical sense that starting from this formulation can be finding in a more general form the maximum work principle together with an equivalent form for the friction term. An application in the case of a plane compression of a plastic material shows the feasibility of the proposed minimization problem formulation to find analytical solution for both cases: one without friction influence and a second which take into account Tresca friction law. To valid the proposed formulation, a comparison with a classical analytical analysis based on slices, upper/lower bound methods and numerical Finite Element simulation is also presented.

Nonverbal working memory of humans and monkeys: rehearsal in the sketchpad?

NASA Technical Reports Server (NTRS)

Washburn, D. A.; Astur, R. S.; Rumbaugh, D. M. (Principal Investigator)

1998-01-01

Investigations of working memory tend to focus on the retention of verbal information. The present experiments were designed to characterize the active maintenance rehearsal process used in the retention of visuospatial information. Rhesus monkeys (Macaca mulatta; N = 6) were tested as well as humans (total N = 90) because these nonhuman primates have excellent visual working memory but, unlike humans, cannot verbally recode the stimuli to employ verbal rehearsal mechanisms. A series of experiments was conducted using a distractor-task paradigm, a directed forgetting procedure, and a dual-task paradigm. No evidence was found for an active maintenance process for either species. Rather, it appears that information is maintained in the visuospatial sketchpad without active rehearsal.

Do Work-Related Mechanical and Psychosocial Factors Contribute to the Social Gradient in Low Back Pain?: A 3-Year Follow-Up Study of the General Working Population in Norway.

PubMed

Sterud, Tom; Johannessen, Håkon A; Tynes, Tore

2016-07-01

A prospective cohort study. The aim of the study was to investigate the extent to which work-related factors contribute to the social gradient in low back pain (LBP). A social gradient in LBP is well established, but only a few studies have examined the extent to which exposure to mechanical and psychosocial work environment factors is a pathway for this gradient. A randomly drawn cohort from the general population in Norway aged 18 to 66 years was followed up for 3 years (n = 12,550, response rate at baseline = 67%). Eligible respondents were in paid work during 2006 and 2009 (n = 6819). Based on administrative register data respondents were coded into five educational levels (university/college ≥4 years was set as the reference group). Outcome of interest was self-reported moderate or severe LBP at follow-up adjusted for baseline LBP. In total, 11.2% (397 individuals) men and 14.5% (461 individual) women reported LBP at follow-up. There was a strong social gradient ranging from 16.4% (elementary) to 6.4% (university/college ≥4 years). The corresponding figures among women were 22.4% and 7.5%. Corrected for age, LBP at baseline and working hours, educational level was a significant predictor of LBP at follow-up (odds ratios 1.8-2.3 in men and 1.7-3.1 in women). Adjusting for mechanical factors reduced the gradient by 39% to 43% in men and 28% to 34% in women. Adjusting for psychosocial factors reduced the gradient by 5% to 12% in men and increased the gradient by 7% to 11% in women. Work-related mechanical factors contributed substantially to the social gradient in LBP among both men and women. The impact of psychosocial factors was modest among men and contributed to an increased gradient among women. 3.

Work-related agricultural fatalities in Australia, 1982-1984.

PubMed

Erlich, S M; Driscoll, T R; Harrison, J E; Frommer, M S; Leigh, J

1993-06-01

Work-related agricultural fatalities were examined as part of a larger population-based study of all work-related fatalities in Australia in the period 1982-1984. A total of 257 farm-related fatalities were identified, of which 223 were deaths of persons in the employed civilian labor force (19.4 deaths per 100,000 persons per year) and 34 were deaths of children less than 15 years of age. The fatality incidence was higher among men, older age groups, and nonmanagers in general and in certain occupations in particular. Mobile mechanical equipment (particularly tractors) was the main fatal agent, roll-overs accounting for many of the fatalities. Better provision of information to agricultural workers, improvements in compliance to and enforcement of legislation, and changes in farming work practices are recommended to improve the safety of farms and farm work.

The contribution of volume, technique, and load to single-repetition and total-repetition kinematics and kinetics in response to three loading schemes.

PubMed

Crewther, Blair T; Cronin, John; Keogh, Justin W L

2008-11-01

This study examined the effect of volume, technique, and load upon single-repetition and total-repetition kinematics and kinetics during three loading schemes. Eleven recreationally trained males each performed a power (8 sets of 6 repetitions at 45% of one-repetition maximum [1RM], 3-minute rest periods, explosive and ballistic movements), hypertrophy (10 sets of 10 repetitions at 75% 1RM, 2-minute rest periods, controlled movements), and maximal strength (6 sets of 4 repetitions at 88% 1RM, 4-minute rest periods, explosive intent) scheme involving squats. Examination of repetition data showed that load intensity (% 1RM) generally had a direct effect on forces, contraction times, impulses, and work (i.e., increasing with load), whereas power varied across loads (p < 0.001). However, total-repetition forces, contraction times, impulses, work, and power were all greater in the hypertrophy scheme (p < 0.001), because of the greater number of repetitions performed (volume) as well as lifting technique. No differences in total forces were found between the equal-volume power and maximal strength schemes, but the former did produce greater total contraction times, work, and power (p < 0.001), which may also be attributed to repetition and technique differences. Total impulses were the only variable greater in the maximal strength scheme (p < 0.001). Thus, the interaction of load, volume, and technique plays an important role in determining the mechanical responses (stimuli) afforded by these workouts. These findings may explain disparities cited within research, regarding the effectiveness of different loading strategies for hypertrophy, maximal strength, and power adaptation.

The mechanics and energetics of human walking and running: a joint level perspective.

PubMed

Farris, Dominic James; Sawicki, Gregory S

2012-01-07

Humans walk and run at a range of speeds. While steady locomotion at a given speed requires no net mechanical work, moving faster does demand both more positive and negative mechanical work per stride. Is this increased demand met by increasing power output at all lower limb joints or just some of them? Does running rely on different joints for power output than walking? How does this contribute to the metabolic cost of locomotion? This study examined the effects of walking and running speed on lower limb joint mechanics and metabolic cost of transport in humans. Kinematic and kinetic data for 10 participants were collected for a range of walking (0.75, 1.25, 1.75, 2.0 m s(-1)) and running (2.0, 2.25, 2.75, 3.25 m s(-1)) speeds. Net metabolic power was measured by indirect calorimetry. Within each gait, there was no difference in the proportion of power contributed by each joint (hip, knee, ankle) to total power across speeds. Changing from walking to running resulted in a significant (p = 0.02) shift in power production from the hip to the ankle which may explain the higher efficiency of running at speeds above 2.0 m s(-1) and shed light on a potential mechanism behind the walk-run transition.

The optimization of total laboratory automation by simulation of a pull-strategy.

PubMed

Yang, Taho; Wang, Teng-Kuan; Li, Vincent C; Su, Chia-Lo

2015-01-01

Laboratory results are essential for physicians to diagnose medical conditions. Because of the critical role of medical laboratories, an increasing number of hospitals use total laboratory automation (TLA) to improve laboratory performance. Although the benefits of TLA are well documented, systems occasionally become congested, particularly when hospitals face peak demand. This study optimizes TLA operations. Firstly, value stream mapping (VSM) is used to identify the non-value-added time. Subsequently, batch processing control and parallel scheduling rules are devised and a pull mechanism that comprises a constant work-in-process (CONWIP) is proposed. Simulation optimization is then used to optimize the design parameters and to ensure a small inventory and a shorter average cycle time (CT). For empirical illustration, this approach is applied to a real case. The proposed methodology significantly improves the efficiency of laboratory work and leads to a reduction in patient waiting times and increased service level.

[Increase of physical activity by improvement of the nutritional status].

PubMed

Torún, B

1989-09-01

Physical activity is affected by nutritional modifications and, in turn, influences growth, cognition, social behavior, work performance and other functions. Studies in preschool children showed that: 1. A decrease in energy intake during four to seven days reduced the time allocated to energy-demanding activities and increased sedentary activities. 2. Children with mild weight deficit were more sedentary than well-nourished counterparts. 3. Children became more active when nutritional status improved. 4. A 10% reduction in energy intake reduced total energy expenditure by 15% without affecting weight gain nor basal metabolism. Studies of men working in non-mechanized agriculture showed that: 1. Dietary improvements led to faster salaried work, reduction of napping time and greater physical activity after work. 2. An increase in energy intake increased total daily energy expenditure, tending to maintain energy balance and relatively stable body weight within the cyclic variations of the agricultural year. 3. Food supplementation did not necessarily improve productivity. Other labor incentives without dietary improvements increased energy expenditure during working hours, which resulted in weight loss. In conclusion, good health and nutrition provide the biological basis for adequate physical activity that may improve cognitive development, social interactions, economic productivity and the quality of life of an individual or a population, but other incentives are required for the optimal expression of that biologic potential.

Nonlinear Multiscale Modeling of 3D Woven Fiber Composites under Ballistic Loading

DTIC Science & Technology

2013-07-11

contact parameters on the underlying damage processes is being studied and worked on. We further develop a material model suitable particularly for...of Material and Process Engineering. 2011/05/23 00:00:00, . : , TOTAL: 1 (d) Manuscripts Number of Peer-Reviewed Conference Proceeding publications...continuum damage mechanics suitable for polymer materials. The effect of contact parameters on the underlying damage processes is being studied and

A numerical investigation into the influence of the properties of cobalt chrome cellular structures on the load transfer to the periprosthetic femur following total hip arthroplasty.

PubMed

Hazlehurst, Kevin Brian; Wang, Chang Jiang; Stanford, Mark

2014-04-01

Stress shielding of the periprosthetic femur following total hip arthroplasty is a problem that can promote the premature loosening of femoral stems. In order to reduce the need for revision surgery it is thought that more flexible implant designs need to be considered. In this work, the mechanical properties of laser melted square pore cobalt chrome molybdenum cellular structures have been incorporated into the design of a traditional monoblock femoral stem. The influence of incorporating the properties of cellular structures on the load transfer to the periprosthetic femur was investigated using a three dimensional finite element model. Eleven different stiffness configurations were investigated by using fully porous and functionally graded approaches. This investigation confirms that the periprosthetic stress values depend on the stiffness configuration of the stem. The numerical results showed that stress shielding is reduced in the periprosthetic Gruen zones when the mechanical properties of cobalt chrome molybdenum cellular structures are used. This work identifies that monoblock femoral stems manufactured using a laser melting process, which are designed for reduced stiffness, have the potential to contribute towards reducing stress shielding. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Occupational injuries identified by an emergency department based injury surveillance system in Nicaragua

PubMed Central

Noe, R; Rocha, J; Clavel-Arcas, C; Aleman, C; Gonzales, M; Mock, C

2004-01-01

Objectives: To identify and describe the work related injuries in both the formal and informal work sectors captured in an emergency department based injury surveillance system in Managua, Nicaragua. Setting: Urban emergency department in Managua, Nicaragua serving 200–300 patients per day. Methods: Secondary analysis from the surveillance system data. All cases indicating an injury while working and seen for treatment at the emergency department between 1 August 2001 and 31 July 2002 were included. There was no exclusion based on place of occurrence (home, work, school), age, or gender. Results: There were 3801 work related injuries identified which accounted for 18.6% of the total 20 425 injures captured by the surveillance system. Twenty seven work related fatalities were recorded, compared with the 1998 International Labor Organization statistic of 25 occupational fatalities for all of Nicaragua. Injuries occurring outside of a formal work location accounted for more than 60% of the work related injuries. Almost half of these occurred at home, while 19% occurred on the street. The leading mechanisms for work related injuries were falls (30%), blunt objects (28%), and stabs/cuts (23%). Falls were by far the most severe mechanism in the study, causing 37% of the work related deaths and more than half of the fractures. Conclusions: Occupational injuries are grossly underreported in Nicaragua. This study demonstrated that an emergency department can be a data source for work related injuries in developing countries because it captures both the formal and informal workforce injuries. Fall prevention initiatives could significantly reduce the magnitude and severity of occupational injuries in Managua, Nicaragua. PMID:15314050

Experimental Investigations on the Surface-Driven Capillary Flow of Aqueous Microparticle Suspensions in the Microfluidic Laboratory-On Systems

NASA Astrophysics Data System (ADS)

Mukhopadhyay, Subhadeep

In this work, total 1592 individual leakage-free polymethylmethacrylate (PMMA) microfluidic devices as laboratory-on-a-chip systems are fabricated by maskless lithography, hot embossing lithography, and direct bonding technique. Total 1094 individual Audio Video Interleave Files as experimental outputs related to the surface-driven capillary flow have been recorded and analyzed. The influence of effective viscosity, effect of surface wettability, effect of channel aspect ratio, and effect of centrifugal force on the surface-driven microfluidic flow of aqueous microparticle suspensions have been successfully and individually investigated in these laboratory-on-a-chip systems. Also, 5 micron polystyrene particles have been separated from the aqueous microparticle suspensions in the microfluidic lab-on-a-chip systems of modified design with 98% separation efficiency, and 10 micron polystyrene particles have been separated with 100% separation efficiency. About the novelty of this work, the experimental investigations have been performed on the surface-driven microfluidic flow of aqueous microparticle suspensions with the investigations on the separation time in particle-size based separation mechanism to control these suspensions in the microfluidic lab-on-a-chip systems. This research work contains a total of 10,112 individual experimental outputs obtained using total 30 individual instruments by author’s own hands-on completely during more than three years continuously. Author has performed the experimental investigations on both the fluid statics and fluid dynamics to develop an automated fluid machine.

Costs and outcome for serious hand and arm injuries during the first year after trauma - a prospective study.

PubMed

Rosberg, Hans-Eric; Carlsson, Katarina Steen; Cederlund, Ragnhild I; Ramel, Eva; Dahlin, Lars B

2013-05-24

To study costs and outcome for serious hand and arm injuries during the first year after the trauma. In patients with a Hand Injury Severity Score (HISS) > 50, DASH and EQ-5D scores as well as factors related to costs within the health care sector, costs due to lost production and total costs were evaluated. Cox-regression analysis stratifying for mechanism of injury was used to analyse return to work. The majority of the 45 included patients (median 42 years 16-64) were men with severe (n = 9) or major (n = 36) injuries with different type of injuries (amputations n = 13; complex injuries n = 18; major nerve injuries/full house n = 13; burn injury n = 1). DASH and EQ-5D decreased and increased, respectively, significantly over time during one year. Total costs (+34%) and costs of lost production were highest for persons injured at work. Factors associated with higher health care costs were age >50 years (+52%), injury at work (+40%) and partial labour market activity (+66%). Costs of lost production had a significant role in total costs of injury. Patients with major injuries had longer duration of sick leave. Patients with severe injuries were more likely to return to work [(RR 3.76 (95% CI 1.38-10.22) from Cox regression, controlling for age, gender and presence of nerve injury]. Despite the fact that work environments have constantly improved over the last decades, we found that hand injuries at work were most costly both in terms of health care and costs of lost production, although the severity, i.e. HISS, did not differ from injuries occurring at home or during leisure.

Analysis of GaAs and Si solar energy hybrid systems

NASA Technical Reports Server (NTRS)

Heinbockel, J. H.; Roberts, A. S., Jr.

1977-01-01

Various silicon hybrid systems are modeled and compared with a gallium arsenide hybrid system. The hybrid systems modeled produce electric power and also thermal power which can be used for heating or air conditioning. Various performance indices are defined and used to compare the system performance: capital cost per electric power out; capital cost per total power out; capital cost per electric power plus mechanical power; annual cost per annual electric energy; and annual cost per annual electric energy plus annual mechanical work. These performance indices indicate that concentrator hybrid systems can be cost effective when compared with present day energy costs.

Evaluating the Effect of Rainfall Infiltration on the Slope Stability of T16 tower of Taipei Mao-kong Gondola by Numerical Methods

NASA Astrophysics Data System (ADS)

RUNG, J.

2013-12-01

In this study, a series of rainfall-stability analyses were performed to simulate the failure mechanism and the function of remediation works of the down slope of T-16 tower pier, Mao-Kong gondola (or T-16 Slope) at the hillside of Taipei City using two-dimensional finite element method. The failure mechanism of T-16 Slope was simulated using the rainfall hyetograph of Jang-Mi typhoon in 2008 based on the field investigation data, monitoring data, soil/rock mechanical testing data and detail design plots of remediation works. Eventually, the numerical procedures and various input parameters in the analysis were verified by comparing the numerical results with the field observations. In addition, 48 hrs design rainfalls corresponding to 5, 10, 25 and 50 years return periods were prepared using the 20 years rainfall data of Mu-Zha rainfall observation station, Central Weather Bureau for the rainfall-stability analyses of T-16 Slope to inspect the effect of the compound stabilization works on the overall stability of the slope. At T-16 Slope, without considering the longitudinal and transverse drainages on the ground surface, there totally 4 types of stabilization works were installed to stabilize the slope. From the slope top to the slope toe, the stabilization works of T-16 Slope consists of RC-retaining wall with micro-pile foundation at the up-segment, earth anchor at the up-middle-segment, soil nailing at the middle-segment and retaining pile at the down-segment of the slope. The effect of each individual stabilization work on the slope stability under rainfall condition was examined and evaluated by raising field groundwater level.

Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong.

PubMed

Wong, Francis K W; Chan, Albert P C; Wong, Andy K D; Hon, Carol K H; Choi, Tracy N Y

2018-03-10

A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the "Public Works Programme Construction Site Safety and Environmental Statistics" (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to 'fall of person from height'; (2) electricians with zero to five years of experience were prone to 'slip, trip or fall on same level'; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched.

Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong

PubMed Central

Wong, Francis K. W.; Chan, Albert P. C.; Wong, Andy K. D.; Choi, Tracy N. Y.

2018-01-01

A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the “Public Works Programme Construction Site Safety and Environmental Statistics” (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to ‘fall of person from height’; (2) electricians with zero to five years of experience were prone to ‘slip, trip or fall on same level’; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched. PMID:29534429

Dynamics of in vivo power output and efficiency of Nasonia asynchronous flight muscle.

PubMed

Lehmann, Fritz-Olaf; Heymann, Nicole

2006-06-25

By simultaneously measuring aerodynamic performance, wing kinematics, and metabolic activity, we have estimated the in vivo limits of mechanical power production and efficiency of the asynchronous flight muscle (IFM) in three species of ectoparasitoid wasps genus Nasonia (N. giraulti, N. longicornis, and N. vitripennis). The 0.6 mg animals were flown under tethered flight conditions in a flight simulator that allowed modulation of power production by employing an open-loop visual stimulation technique. At maximum locomotor capacity, flight muscles of Nasonia are capable to sustain 72.2 +/- 18.3 W kg(-1) muscle mechanical power at a chemo-mechanical conversion efficiency of approximately 9.8 +/- 0.9%. Within the working range of the locomotor system, profile power requirement for flight dominates induced power requirement suggesting that the cost to overcome wing drag places the primary limit on overall flight performance. Since inertial power is only approximately 25% of the sum of induced and profile power requirements, Nasonia spp. may not benefit from elastic energy storage during wing deceleration phases. A comparison between wing size-polymorphic males revealed that wing size reduction is accompanied by a decrease in total flight muscle volume, muscle mass-specific mechanical power production, and total flight efficiency. In animals with small wings maximum total flight efficiency is below 0.5%. The aerodynamic and power estimates reported here for Nasonia are comparable to values reported previously for the fruit fly Drosophila flying under similar experimental conditions, while muscle efficiency of the tiny wasp is more at the lower end of values published for various other insects.

Spring-like Ankle Foot Orthoses reduce the energy cost of walking by taking over ankle work.

PubMed

Bregman, D J J; Harlaar, J; Meskers, C G M; de Groot, V

2012-01-01

In patients with central neurological disorders, gait is often limited by a reduced ability to push off with the ankle. To overcome this reduced ankle push-off, energy-storing, spring-like carbon-composite Ankle Foot Orthoses (AFO) can be prescribed. It is expected that the energy returned by the AFO in late stance will support ankle push-off, and reduce the energy cost of walking. In 10 patients with multiple sclerosis and stroke the energy cost of walking, 3D kinematics, joint power, and joint work were measured during gait, with and without the AFO. The mechanical characteristics of the AFO were measured separately, and used to calculate the contribution of the AFO to the ankle kinetics. We found a significant decrease of 9.8% in energy cost of walking when walking with the AFO. With the AFO, the range of motion of the ankle was reduced by 12.3°, and the net work around the ankle was reduced by 29%. The total net work in the affected leg remained unchanged. The AFO accounted for 60% of the positive ankle work, which reduced the total amount of work performed by the leg by 11.1% when walking with the AFO. The decrease in energy cost when walking with a spring-like energy-storing AFO in central neurological patients is not induced by an augmented net ankle push-off, but by the AFO partially taking over ankle work. Copyright © 2011 Elsevier B.V. All rights reserved.

Respiratory mechanics in infants with severe bronchiolitis on controlled mechanical ventilation.

PubMed

Cruces, Pablo; González-Dambrauskas, Sebastián; Quilodrán, Julio; Valenzuela, Jorge; Martínez, Javier; Rivero, Natalia; Arias, Pablo; Díaz, Franco

2017-10-06

Analysis of respiratory mechanics during mechanical ventilation (MV) is able to estimate resistive, elastic and inertial components of the working pressure of the respiratory system. Our aim was to discriminate the components of the working pressure of the respiratory system in infants on MV with severe bronchiolitis admitted to two PICU's. Infants younger than 1 year old with acute respiratory failure caused by severe bronchiolitis underwent neuromuscular blockade, tracheal intubation and volume controlled MV. Shortly after intubation studies of pulmonary mechanics were performed using inspiratory and expiratory breath hold. The maximum inspiratory and expiratory flow (QI and QE) as well as peak inspiratory (PIP), plateau (PPL) and total expiratory pressures (tPEEP) were measured. Inspiratory and expiratory resistances (RawI and RawE) and Time Constants (K TI and K TE ) were calculated. We included 16 patients, of median age 2.5 (1-5.8) months. Bronchiolitis due to respiratory syncytial virus was the main etiology (93.8%) and 31.3% had comorbidities. Measured respiratory pressures were PIP 29 (26-31), PPL 24 (20-26), tPEEP 9 [8-11] cmH2O. Elastic component of the working pressure was significantly higher than resistive and both higher than threshold (tPEEP - PEEP) (P < 0.01). QI was significantly lower than QE [5 (4.27-6.75) v/s 16.5 (12-23.8) L/min. RawI and RawE were 38.8 (32-53) and 40.5 (22-55) cmH2O/L/s; K TI and K TE [0.18 (0.12-0.30) v/s 0.18 (0.13-0.22) s], and K TI :K TE ratio was 1:1.04 (1:0.59-1.42). Analysis of respiratory mechanics of infants with severe bronchiolitis receiving MV shows that the elastic component of the working pressure of the respiratory system is the most important. The elastic and resistive components in conjunction with flow profile are characteristic of restrictive diseases. A better understanding of lung mechanics in this group of patients may lead to change the traditional ventilatory approach to severe bronchiolitis.

Biophysical Characteristics of Chemical Protective Ensemble With and Without Body Armor

DTIC Science & Technology

2015-07-01

Environmental Medicine Natick, MA 01760-5007 Standard Form 298 (Rev. 8/98) REPORT DOCUMENTATION PAGE Prescribed by ANSI Std. Z39.18 Form Approved OMB...members deployed to Iraq/Afghanistan, heat injuries totally 909, 58 of these being heat stroke [1]. While these incidences are relatively high across...As homeotherms, metabolic energy production (?̇?) in humans is a natural process, where ~20% of this energy results in useful mechanical work and

Corrosion behaviour and mechanical properties of functionally gradient materials developed for possible hard-tissue applications.

PubMed

Becker, B S; Bolton, J D

1997-12-01

Artificial hip joints have an average lifetime of 10 years due to aseptic loosening of the femoral stem attributed to polymeric wear debris; however, there is a steadily increasing demand from younger osteoarthritis patients aged between 15 and 40 year for a longer lasting joint of 25 years or more. Compliant layers incorporated into the acetabular cup generate elastohydrodynamic lubrication conditions between the bearing surfaces, reduce joint friction coefficients and wear debris production and could increase the average life of total hip replacements, and other human load-bearing joint replacements, i.e. total knee replacements. Poor adhesion between a fully dense substrate and the compliant layer has so far prevented any further exploitation. This work investigated the possibility of producing porous metallic, functionally gradient type acetabular cups using powder metallurgy techniques - where a porous surface was supported by a denser core - into which the compliant layers could be incorporated. The corrosion behaviour and mechanical properties of three biomedically approved alloys containing two levels of total porosity (>30% and <10%) were established, resulting in Ti-6Al-4V being identified as the most promising biocompatible functionally graded material, not only for this application but for other hard-tissue implants.

Structural, mechanical and myothermic properties of rabbit rectococcygeus muscle.

PubMed Central

Davey, D F; Gibbs, C L; McKirdy, H C

1975-01-01

1. The fine structure of rabbit rectococcygeus muscle has been studied with the electron microscope. 2. The mechanical performance and the heat production of this muscle has been investigated during tetanic contractions at 27 degrees C. 3. In isometric contractions a force of 164 +/- 27 mN/mm2 (mean +/- S.D., n = 17) is developed and the heat production is linearly related to the force. 4. There is a relationship between the duration of stimulation (t) and the total heat production (H) of the type H = A plus bt, where A and b are constants. 5. After-loaded isotonic experiments show that the relationship between force and velocity can be fitted by the 'characteristic equation' of Hill (1938). 6. The value of a/P0 (0-302 +/- 0-093, mean +/- S.D.) is slightly higher than in frog skeletal muscle but the constant b is about 50 times smaller. 7. The ratio of work/total energy production, for the stimulus conditions employed, was maximally 0-185. 8. The ratio of total enthalpy to initial enthalpy is difficult to measure accurately but is probably about 2. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 Plate 2 PMID:1151809

Contributions to Crustal Mechanics on Europa from Subterranean Ocean Vibrations

NASA Astrophysics Data System (ADS)

Hayes, Robert

2016-03-01

The recent discovery of subduction zones on Europa demonstrated a significant step forward in understanding the moon's surface mechanics. This work promotes the additional consideration that the surface mechanics have contributions from small relative pressure differentials in the subsurface ocean that create cracks in the surface which are then filled, sealed and healed. Crack formation can be small, as interior pressure can relatively easily breach the surface crust, generating cracks followed by common fracture formation backfilled with frozen liquid. This process will slowly increase the overall surface area of the moon with each sealed crack and fracture increasing the total surface area. This creeping growth of surface area monotonically decreases subsurface pressure which can eventually catastrophically subduct large areas of surface and so is consistent with current knowledge of observational topology on Europa. This tendency is attributed to a relatively lower energy threshold to crack the surface from interior overpressures, but a higher energy threshold to crush the spherical surface due to subsurface underpressures. Proposed mechanisms for pressure differentials include tidal forces whose Fourier components build up the resonant oscillatory modes of the subsurface ocean creating periodic under and overpressure events below the crust. This mechanism provides a means to continually reform the surface of the moon over short geological time scales. This work supported in part by federal Grant NRC-HQ-84-14-G-0059.

[Health effects and psychological stress in pregnant women engaged in work outside the home].

PubMed

Anan, Ayumi; Shiiba, Michiyo; Sibata, Eiji; Kawamoto, Rieko

2010-12-01

Modern society demands working conditions in which pregnant women can successfully deliver children and maintain a professional position. The aim of this study is to investigate the effects of work on the health and psychological stress in working women and their newborns. We reviewed twenty-eight publications and found that health problems in working women occur at high rates. However, there is no report investigating the mechanism by which health problems occur, or describing the precise working conditions and symptoms in pregnant women who are engaged in work outside the home. In addition, the literature uses subjective evaluations, including psychological tests, to quantify stress and anxiety, but no biochemical analyses of stress-related substances were conducted. We suggest that a standard index to represent working conditions and job category, as well as an investigation of the workload of house-keeping, is needed to understand the total work effort by pregnant women in modern times. Finally, measurement of stress-related biological markers may be effective in the investigation from various perspectives of occupational stress in pregnant women.

Teachers' work ability: a study of relationships between collective efficacy and self-efficacy beliefs.

PubMed

Guidetti, Gloria; Viotti, Sara; Bruno, Andreina; Converso, Daniela

2018-01-01

Work ability constitutes one of the most studied well-being indicators related to work. Past research highlighted the relationship with work-related resources and demands, and personal resources. However, no studies highlight the role of collective and self-efficacy beliefs in sustaining work ability. The purpose of this study was to examine whether and by which mechanism work ability is linked with individual and collective efficacies in a sample of primary and middle school teachers. Using a dataset consisting of 415 primary and middle school Italian teachers, the analysis tested for the mediating role of self-efficacy between collective efficacy and work ability. Mediational analysis highlights that teachers' self-efficacy totally mediates the relationship between collective efficacy and perceived work ability. Results of this study enhance the theoretical knowledge and empirical evidence regarding the link between teachers' collective efficacy and self-efficacy, giving further emphasis to the concept of collective efficacy in school contexts. Moreover, the results contribute to the study of well-being in the teaching profession, highlighting a process that sustains and promotes levels of work ability through both collective and personal resources.

Effects of acute handling stress on short-term central expression of orexigenic/anorexigenic genes in zebrafish.

PubMed

Cortés, Raul; Teles, Mariana; Oliveira, Miguel; Fierro-Castro, Camino; Tort, Lluis; Cerdá-Reverter, José Miguel

2018-02-01

Physiological mechanisms driving stress response in vertebrates are evolutionarily conserved. These mechanisms involve the activation of both the hypothalamic-sympathetic-chromaffin cell (HSC) and the hypothalamic-pituitary-adrenal (HPA) axes. In fish, the reduction of food intake levels is a common feature of the behavioral response to stress but the central mechanisms coordinating the energetic response are not well understood yet. In this work, we explore the effects of acute stress on key central systems regulating food intake in fish as well as on total body cortisol and glucose levels. We show that acute stress induced a rapid increase in total body cortisol with no changes in body glucose, at the same time promoting a prompt central response by activating neuronal pathways. All three orexigenic peptides examined, i.e., neuropeptide y (npy), agouti-related protein (agrp), and ghrelin, increased their central expression level suggesting that these neuronal systems are not involved in the short-term feeding inhibitory effects of acute stress. By contrast, the anorexigenic precursors tested, i.e., cart peptides and pomc, exhibited increased expression after acute stress, suggesting their involvement in the anorexigenic effects.

Manganese phytate dotted polyaniline shell enwrapped carbon nanotube: Towards the reinforcements in fire safety and mechanical property of polymer.

PubMed

Wang, Junling; Zhan, Jing; Mu, Xiaowei; Jin, Xin; Chu, Fukai; Kan, Yongchun; Xing, Weiyi

2018-06-19

High fire hazard of epoxy resin (EP) has been an unavoidable obstruction on its wide application. Here, a manganese phytate dotted polyaniline shell enwrapped carbon nanotube (MPCNT) is facilely constructed and employed as flame retardant for EP. By adding 4.0 wt% MPCNT, the peak heat release rate, total heat release values, peak CO yields and total CO yields are decreased by 27.2, 12.3, 44.8, and 23.3%, respectively. The decreased absorbance intensity of toxic aromatic volatiles is also observed. Then, a tripartite cooperative flame retardant mechanism (a continuous barrier network, catalytic charring function of phytate, and catalytic activity of MnP/C system) is proposed. Furthermore, the storage modulus of EP composites with 2.0 and 4.0 wt% MPCNT are increased by 23.0 and 25.8% at 40 °C, respectively. Thus, the simultaneous reinforcements in fire safety and mechanical performance of EP are successfully achieved. This work may represent a significant step forward in the facile construction of functionalized carbon materials for achieving their whole potentials in polymer-matrix composite. Copyright © 2018. Published by Elsevier Inc.

Constitutive Modelling and Deformation Band Angle Predictions for High Porosity Sandstones

NASA Astrophysics Data System (ADS)

Richards, M. C.; Issen, K. A.; Ingraham, M. D.

2017-12-01

The development of a field-scale deformation model requires a constitutive framework that is capable of representing known material behavior and able to be calibrated using available mechanical response data. This work employs the principle of hyperplasticity (e.g., Houlsby and Puzrin, 2006) to develop such a constitutive framework for high porosity sandstone. Adapting the works of Zimmerman et al. (1986) and Collins and Houlsby (1997), the mechanical data set of Ingraham et al. (2013 a, b) was used to develop a specific constitutive framework for Castlegate sandstone, a high porosity fluvial-deposited reservoir analog rock. Using the mechanical data set of Ingraham et al. (2013 a, b), explicit expressions and material parameters of the elastic moduli and strain tensors were obtained. With these expressions, analytical and numerical techniques were then employed to partition the total mechanical strain into elastic, coupled, and plastic strain components. With the partitioned strain data, yield surfaces in true-stress space, coefficients of internal friction, dilatancy factors, along with the theorectical predictions of the deformation band angles were obtained. These results were also evaluated against band angle values obtained from a) measurements on specimen jackets (Ingraham et al., 2013a), b) plane fits through located acoustic emissions (AE) events (Ingraham et al. 2013b), and c) X-ray micro-computed tomography (micro-CT) calculations.

Insights into the Anaerobic Biodegradation Pathway of n-Alkanes in Oil Reservoirs by Detection of Signature Metabolites

PubMed Central

Bian, Xin-Yu; Maurice Mbadinga, Serge; Liu, Yi-Fan; Yang, Shi-Zhong; Liu, Jin-Feng; Ye, Ru-Qiang; Gu, Ji-Dong; Mu, Bo-Zhong

2015-01-01

Anaerobic degradation of alkanes in hydrocarbon-rich environments has been documented and different degradation strategies proposed, of which the most encountered one is fumarate addition mechanism, generating alkylsuccinates as specific biomarkers. However, little is known about the mechanisms of anaerobic degradation of alkanes in oil reservoirs, due to low concentrations of signature metabolites and lack of mass spectral characteristics to allow identification. In this work, we used a multidisciplinary approach combining metabolite profiling and selective gene assays to establish the biodegradation mechanism of alkanes in oil reservoirs. A total of twelve production fluids from three different oil reservoirs were collected and treated with alkali; organic acids were extracted, derivatized with ethanol to form ethyl esters and determined using GC-MS analysis. Collectively, signature metabolite alkylsuccinates of parent compounds from C1 to C8 together with their (putative) downstream metabolites were detected from these samples. Additionally, metabolites indicative of the anaerobic degradation of mono- and poly-aromatic hydrocarbons (2-benzylsuccinate, naphthoate, 5,6,7,8-tetrahydro-naphthoate) were also observed. The detection of alkylsuccinates and genes encoding for alkylsuccinate synthase shows that anaerobic degradation of alkanes via fumarate addition occurs in oil reservoirs. This work provides strong evidence on the in situ anaerobic biodegradation mechanisms of hydrocarbons by fumarate addition. PMID:25966798

Estimation of physical work load by statistical analysis of the heart rate in a conveyor-belt worker.

PubMed

Kontosic, I; Vukelić, M; Pancić, M; Kunisek, J

1994-12-01

Physical work load was estimated in a female conveyor-belt worker in a bottling plant. Estimation was based on continuous measurement and on calculation of average heart rate values in three-minute and one-hour periods and during the total measuring period. The thermal component of the heart rate was calculated by means of the corrected effective temperature, for the one-hour periods. The average heart rate at rest was also determined. The work component of the heart rate was calculated by subtraction of the resting heart rate and the heart rate measured at 50 W, using a regression equation. The average estimated gross energy expenditure during the work was 9.6 +/- 1.3 kJ/min corresponding to the category of light industrial work. The average estimated oxygen uptake was 0.42 +/- 0.06 L/min. The average performed mechanical work was 12.2 +/- 4.2 W, i.e. the energy expenditure was 8.3 +/- 1.5%.

All-graphene-battery: bridging the gap between supercapacitors and lithium ion batteries

NASA Astrophysics Data System (ADS)

Kim, Haegyeom; Park, Kyu-Young; Hong, Jihyun; Kang, Kisuk

2014-06-01

Herein, we propose an advanced energy-storage system: all-graphene-battery. It operates based on fast surface-reactions in both electrodes, thus delivering a remarkably high power density of 6,450 W kg-1total electrode while also retaining a high energy density of 225 Wh kg-1total electrode, which is comparable to that of conventional lithium ion battery. The performance and operating mechanism of all-graphene-battery resemble those of both supercapacitors and batteries, thereby blurring the conventional distinction between supercapacitors and batteries. This work demonstrates that the energy storage system made with carbonaceous materials in both the anode and cathode are promising alternative energy-storage devices.

All-graphene-battery: bridging the gap between supercapacitors and lithium ion batteries.

PubMed

Kim, Haegyeom; Park, Kyu-Young; Hong, Jihyun; Kang, Kisuk

2014-06-13

Herein, we propose an advanced energy-storage system: all-graphene-battery. It operates based on fast surface-reactions in both electrodes, thus delivering a remarkably high power density of 6,450 W kg(-1)(total electrode) while also retaining a high energy density of 225 Wh kg(-1)(total electrode), which is comparable to that of conventional lithium ion battery. The performance and operating mechanism of all-graphene-battery resemble those of both supercapacitors and batteries, thereby blurring the conventional distinction between supercapacitors and batteries. This work demonstrates that the energy storage system made with carbonaceous materials in both the anode and cathode are promising alternative energy-storage devices.

Total Synthesis of Ionic Liquid Systems for Dissolution of Lunar Simulant

NASA Technical Reports Server (NTRS)

Sharpe, Robert J.; Karr, Laurel J.; Paley, Mark S.

2010-01-01

For purposes of Space Resource Utilization, work in the total synthesis of a new ionic liquid system for the extraction of oxygen and metals from lunar soil is studied and described. Reactions were carried out according to procedures found in the chemical literature, analyzed via Thin-Layer Chromatography and 1H Nuclear Magnetic Resonance Spectroscopy and purified via vacuum distillation and rotary evaporation. Upon final analysis via 1H NMR, it was found that while the intermediates of the synthesis had been achieved, unexpected side products were also present. The mechanisms and constraints of the synthesis are described as well as the final results of the project and recommendations for continued study

All-graphene-battery: bridging the gap between supercapacitors and lithium ion batteries

PubMed Central

Kim, Haegyeom; Park, Kyu-Young; Hong, Jihyun; Kang, Kisuk

2014-01-01

Herein, we propose an advanced energy-storage system: all-graphene-battery. It operates based on fast surface-reactions in both electrodes, thus delivering a remarkably high power density of 6,450 W kg−1total electrode while also retaining a high energy density of 225 Wh kg−1total electrode, which is comparable to that of conventional lithium ion battery. The performance and operating mechanism of all-graphene-battery resemble those of both supercapacitors and batteries, thereby blurring the conventional distinction between supercapacitors and batteries. This work demonstrates that the energy storage system made with carbonaceous materials in both the anode and cathode are promising alternative energy-storage devices. PMID:24923290

Evaluation of mechanical deformation and distributive magnetic loads with different mechanical constraints in two parallel conducting bars

NASA Astrophysics Data System (ADS)

Lee, Ho-Young; Lee, Se-Hee

2017-08-01

Mechanical deformation, bending deformation, and distributive magnetic loads were evaluated numerically and experimentally for conducting materials excited with high current. Until now, many research works have extensively studied the area of magnetic force and mechanical deformation by using coupled approaches such as multiphysics solvers. In coupled analysis for magnetoelastic problems, some articles and commercial software have presented the resultant mechanical deformation and stress on the body. To evaluate the mechanical deformation, the Lorentz force density method (LZ) and the Maxwell stress tensor method (MX) have been widely used for conducting materials. However, it is difficult to find any experimental verification regarding mechanical deformation or bending deformation due to magnetic force density. Therefore, we compared our numerical results to those from experiments with two parallel conducting bars to verify our numerical setup for bending deformation. Before showing this, the basic and interesting coupled simulation was conducted to test the mechanical deformations by the LZ (body force density) and the MX (surface force density) methods. This resulted in MX gave the same total force as LZ, but the local force distribution in MX introduced an incorrect mechanical deformation in the simulation of a solid conductor.

Mechanical work and efficiency of 5 + 5 m shuttle running.

PubMed

Zamparo, Paola; Pavei, Gaspare; Nardello, Francesca; Bartolini, Davide; Monte, Andrea; Minetti, Alberto E

2016-10-01

Acceleration and deceleration phases characterise shuttle running (SR) compared to constant speed running (CR); mechanical work is thus expected to be larger in the former compared to the latter, at the same average speed (v mean). The aim of this study was to measure total mechanical work (W tot (+) , J kg(-1) m(-1)) during SR as the sum of internal (W int (+) ) and external (W ext (+) ) work and to calculate the efficiency of SR. Twenty males were requested to perform shuttle runs over a distance of 5 + 5 m at different speeds (slow, moderate and fast) to record kinematic data. Metabolic data were also recorded (at fast speed only) to calculate energy cost (C, J kg(-1) m(-1)) and mechanical efficiency (eff(+) = W tot (+) C (-1)) of SR. Work parameters significantly increased with speed (P < 0.001): W ext (+)  = 1.388 + 0.337 v mean; W int (+)  = -1.002 + 0.853 v mean; W tot (+)  = 1.329 v mean. At the fastest speed C was 27.4 ± 2.6 J kg(-1) m(-1) (i.e. about 7 times larger than in CR) and eff(+) was 16.2 ± 2.0 %. W ext (+) is larger in SR than in CR (2.5 vs. 1.4 J kg(-1) m(-1) in the range of investigated speeds: 2-3.5 m s(-1)) and W int (+) , at fast speed, is about half of W tot (+) . eff(+) is lower in SR (16 %) than in CR (50-60 % at comparable speeds) and this can be attributed to a lower elastic energy reutilization due to the acceleration/deceleration phases over this short shuttle distance.

Use of natural clinoptilolite for the removal of lead, copper and zinc in fixed bed column.

PubMed

Stylianou, Marinos A; Hadjiconstantinou, Michalis P; Inglezakis, Vasilis J; Moustakas, Konstantinos G; Loizidou, Maria D

2007-05-08

This work deals with the removal of lead, copper and zinc from aqueous solutions by using natural zeolite (clinoptilolite). Fixed bed experiments were performed, using three different volumetric flow rates of 5, 7 and 10bed volume/h, under a total normality of 0.01N, at initial pH of 4 and ambient temperature (25 degrees C). The removal efficiency increased when decreasing the flow rate and the following selectivity series was found: Pb(2+)>Zn(2+)> or =Cu(2+). Conductivity measurements showed that lead removal follows mainly ion exchange mechanism, while copper and zinc removal follows ion exchange and sorption mechanism as well.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pestehe, S. J., E-mail: sjpest@tabrizu.ac.ir; Mohammadnejad, M.; Research Institute for Applied Physics and Astronomy, University of Tabriz, Tabriz

A theoretical model is developed to study the signals from a typical dynamic Faraday cup, and using this model the output signals from this structure are obtained. A detailed discussion on the signal structure, using different experimental conditions, is also given. It is argued that there is a possibility of determining the total charge of the generated ion pulse, the maximum velocity of the ions, ion velocity distribution, and the number of ion species for mixed working gases, under certain conditions. In addition, the number of different ionization stages, the number of different pinches in one shot, and the numbermore » of different existing acceleration mechanisms can also be determined provided that the mentioned conditions being satisfied. An experiment is carried out on the Filippov type 90 kJ Sahand plasma focus using Ar as the working gas at the pressure of 0.25 Torr. The data from a typical shot are fitted to a signal from the model and the total charge of the related energetic ion pulse is deduced using the values of the obtained fit parameters. Good agreement between the obtained amount of the total charge and the values obtained during other experiments on the same plasma focus device is observed.« less

Individual characteristics in occupational accidents due to imbalance: a case-control study of the employees of a railway company.

PubMed

Gauchard, G C; Chau, N; Touron, C; Benamghar, L; Dehaene, D; Perrin, PhP; Mur, J-M

2003-05-01

Falls are frequent occupational accidents, and are responsible for a significant amount of lost working time and, more importantly, for a high mortality. The factors involved in falling mechanisms can be of external or individual origin, the latter being less well identified. To assess the relations between certain individual characteristics and occupational accidents due to imbalance. A total of 427 male employees, who had been victims of at least one occupational accident with sick leave due to imbalance (cases) and 427 controls were recruited among the employees of a large French railway company. A standardised questionnaire on life conditions and professional factors, and a description of the accidents was filled in by an occupational physician for each subject. Some job categories were more affected by a specific release mechanism of work related falls. Certain individual characteristics such as smoking, alcohol consumption, inactivity, sleep disorders, and request for a job change were correlated with the occurrence of occupational accidents. Sick leaves of eight days or over were more frequent in older and overweight injured workers. Some lesions were linked with the specific fall released mechanisms. Individual characteristics can increase the risk of occupational accidents, especially falling. This study identified subjects most at risk on whom prevention related to working conditions and falls could be focused.

Old men running: mechanical work and elastic bounce.

PubMed

Cavagna, G A; Legramandi, M A; Peyré-Tartaruga, L A

2008-02-22

It is known that muscular force is reduced in old age. We investigate what are the effects of this phenomenon on the mechanics of running. We hypothesized that the deficit in force would result in a lower push, causing reduced amplitude of the vertical oscillation, with smaller elastic energy storage and increased step frequency. To test this hypothesis, we measured the mechanical energy of the centre of mass of the body during running in old and young subjects. The amplitude of the oscillation is indeed reduced in the old subjects, resulting in an approximately 20% smaller elastic recovery and a greater step frequency (3.7 versus 2.8 Hz, p=1.9x10(-5), at 15-17 km h(-1)). Interestingly, the greater step frequency is due to a lower aerial time, and not to a greater natural frequency of the system, which is similar in old and young subjects (3.6 versus 3.4 Hz, p=0.2). Moreover, we find that in the old subjects, the step frequency is always similar to the natural frequency, even at the highest speeds. This is at variance with young subjects who adopt a step frequency lower than the natural frequency at high speeds, to contain the aerobic energy expenditure. Finally, the external work to maintain the motion of the centre of mass is reduced in the old subjects (0.9 versus 1.2 J kg(-1) m(-1), p=5.1x10(-6)) due to the lower work done against gravity, but the higher step frequency involves a greater internal work to reset the limbs at each step. The net result is that the total work increases with speed more steeply in the old subjects than in young subjects.

Grizzly bear (Ursus arctos horribilis) locomotion: forelimb joint mechanics across speed in the sagittal and frontal planes.

PubMed

Shine, Catherine L; Robbins, Charles T; Nelson, O Lynne; McGowan, Craig P

2017-04-01

The majority of terrestrial locomotion studies have focused on parasagittal motion and paid less attention to forces or movement in the frontal plane. Our previous research has shown that grizzly bears produce higher medial ground reaction forces (lateral pushing from the animal) than would be expected for an upright mammal, suggesting frontal plane movement may be an important aspect of their locomotion. To examine this, we conducted an inverse dynamics analysis in the sagittal and frontal planes, using ground reaction forces and position data from three high-speed cameras of four adult female grizzly bears. Over the speed range collected, the bears used walks, running walks and canters. The scapulohumeral joint, wrist and the limb overall absorb energy (average total net work of the forelimb joints, -0.97 W kg -1 ). The scapulohumeral joint, elbow and total net work of the forelimb joints have negative relationships with speed, resulting in more energy absorbed by the forelimb at higher speeds (running walks and canters). The net joint moment and power curves maintain similar patterns across speed as in previously studied species, suggesting grizzly bears maintain similar joint dynamics to other mammalian quadrupeds. There is no significant relationship with net work and speed at any joint in the frontal plane. The total net work of the forelimb joints in the frontal plane was not significantly different from zero, suggesting that, despite the high medial ground reaction forces, the forelimb acts as a strut in that plane. © 2017. Published by The Company of Biologists Ltd.

Effect of the sagittal ankle angle at initial contact on energy dissipation in the lower extremity joints during a single-leg landing.

PubMed

Lee, Jinkyu; Song, Yongnam; Shin, Choongsoo S

2018-05-01

During landing, the ankle angle at initial contact (IC) exhibits relatively wide individual variation compared to the knee and hip angles. However, little is known about the effect of different IC ankle angles on energy dissipation. The purpose of this study was to investigate the relationship between individual ankle angles at IC and energy dissipation in the lower extremity joints. Twenty-seven adults performed single-leg landings from a 0.3-m height. Kinetics and kinematics of the lower extremity joints were measured. The relationship between ankle angles at IC and negative work, range of motion, the time to peak ground reaction force, and peak loading rate were analyzed. The ankle angle at IC was positively correlated with ankle negative work (r = 0.80, R 2  = 0.64, p < 0.001) and the contribution of the ankle to total (ankle, knee and hip joint) negative work (r = 0.84, R 2  = 0.70, p < 0.001), but the ankle angle was negatively correlated with hip negative work (r = -0.46, R 2  = 0.21, p = 0.01) and the contribution of the hip to total negative work (r = -0.61, R 2  = 0.37, p < 0.001). The knee negative work and the contribution of the knee to total negative work were not correlated with the ankle angle at IC. The ankle angle at IC was positively correlated with total negative work (r = 0.50, R 2  = 0.25, p < 0.01) and negatively correlated with the peak loading rate (r = -0.76, R 2  = 0.57, p < 0.001). These results indicated that landing mechanics changed as the ankle angle at IC increased, such that the ankle energy dissipation increased and redistributed the energy dissipation in the ankle and hip joints. Further, these results suggest that increased ankle energy dissipation with a higher IC plantar flexion angle may be a potential landing technique for reducing the risk of injury to the anterior cruciate ligament and hip musculature. Copyright © 2018 Elsevier B.V. All rights reserved.

Sensor data security level estimation scheme for wireless sensor networks.

PubMed

Ramos, Alex; Filho, Raimir Holanda

2015-01-19

Due to their increasing dissemination, wireless sensor networks (WSNs) have become the target of more and more sophisticated attacks, even capable of circumventing both attack detection and prevention mechanisms. This may cause WSN users, who totally trust these security mechanisms, to think that a sensor reading is secure, even when an adversary has corrupted it. For that reason, a scheme capable of estimating the security level (SL) that these mechanisms provide to sensor data is needed, so that users can be aware of the actual security state of this data and can make better decisions on its use. However, existing security estimation schemes proposed for WSNs fully ignore detection mechanisms and analyze solely the security provided by prevention mechanisms. In this context, this work presents the sensor data security estimator (SDSE), a new comprehensive security estimation scheme for WSNs. SDSE is designed for estimating the sensor data security level based on security metrics that analyze both attack prevention and detection mechanisms. In order to validate our proposed scheme, we have carried out extensive simulations that show the high accuracy of SDSE estimates.

Sensor Data Security Level Estimation Scheme for Wireless Sensor Networks

PubMed Central

Ramos, Alex; Filho, Raimir Holanda

2015-01-01

Due to their increasing dissemination, wireless sensor networks (WSNs) have become the target of more and more sophisticated attacks, even capable of circumventing both attack detection and prevention mechanisms. This may cause WSN users, who totally trust these security mechanisms, to think that a sensor reading is secure, even when an adversary has corrupted it. For that reason, a scheme capable of estimating the security level (SL) that these mechanisms provide to sensor data is needed, so that users can be aware of the actual security state of this data and can make better decisions on its use. However, existing security estimation schemes proposed for WSNs fully ignore detection mechanisms and analyze solely the security provided by prevention mechanisms. In this context, this work presents the sensor data security estimator (SDSE), a new comprehensive security estimation scheme for WSNs. SDSE is designed for estimating the sensor data security level based on security metrics that analyze both attack prevention and detection mechanisms. In order to validate our proposed scheme, we have carried out extensive simulations that show the high accuracy of SDSE estimates. PMID:25608215

Mechanical energy patterns in nordic walking: comparisons with conventional walking.

PubMed

Pellegrini, Barbara; Peyré-Tartaruga, Leonardo Alexandre; Zoppirolli, Chiara; Bortolan, Lorenzo; Savoldelli, Aldo; Minetti, Alberto Enrico; Schena, Federico

2017-01-01

The use of poles during Nordic Walking (NW) actively engages the upper body to propel the body forward during walking. Evidence suggests that NW leads to a longer stride and higher speed, and sometimes to increased ground reaction forces with respect to conventional walking (W). The aim of this study was to investigate if NW is associated with different changes in body centre of mass (COM) motion and limbs energy patterns, mechanical work and efficiency compared to W. Eight experienced Nordic Walkers performed 5-min W and NW trials on a treadmill at 4kmh -1 . Steady state oxygen consumption and movements of body segments and poles were measured during each trial. We found greater fluctuation of kinetic (KE) and potential (PE) energy associated with COM displacement for NW compared to W. An earlier increase of KE for NW than for W, probably due to the propulsive action of poles, modified the synchronization between PE and KE oscillations so that a 10.9% higher pendular recovery between these energies was found in NW. The 10.2% higher total mechanical work found for NW was mainly due to the greater work required to move upper limbs and poles. NW was 20% less efficient and was metabolically more demanding than W, this difference could be ascribed to isometric contraction and low efficiency of upper musculature. Concluding, NW can be considered a highly dynamic gait, with distinctive mechanical features compared to conventional gait, due to pole propulsion and arm/pole swing. Copyright © 2016 Elsevier B.V. All rights reserved.

Analysis of Three-Dimensional Roller Performance in a Micro-g Environment

NASA Technical Reports Server (NTRS)

Roberts, B.; Shook, L.; Hossaini, L.; Cohen, R.

1999-01-01

Approximately 960 hours of extravehicular activity (EVA), or spacewalks, are planned for the construction of the International Space Station over the next six years. This is over two-and-a-half times the total number of EVA hours accumulated by the National Aeronautics and Space Administration (NASA) in the past 35 years of U.S. spaceflight. Therefore, it is advantageous to explore ways to assist astronauts in being more efficient while working in space. The Space Systems Laboratory at the University of Maryland is investigating ways of improving conventional ratcheting tools that do not work effectively in confined spaces and have been seen to exhibit other limitations that restrict their use during EVA. By replacing the traditional ratchet mechanism with a NASA/Goddard Space Flight Center-developed three-dimensional (3-D) sprag and roller mechanism, ratcheting tools can be made more efficient. In October of 1998, a 3-D roller mechanism was flown on space shuttle mission STS-95 as part of the Space Experiment Module program. The goal of the experiment was to quantify the roller's performance when operating for an extended period in a micro-g environment. This paper discusses the design of the experiment, as well as the results obtained.

A Method for Dynamically Selecting the Best Frequency Hopping Technique in Industrial Wireless Sensor Network Applications

PubMed Central

Fernández de Gorostiza, Erlantz; Mabe, Jon

2018-01-01

Industrial wireless applications often share the communication channel with other wireless technologies and communication protocols. This coexistence produces interferences and transmission errors which require appropriate mechanisms to manage retransmissions. Nevertheless, these mechanisms increase the network latency and overhead due to the retransmissions. Thus, the loss of data packets and the measures to handle them produce an undesirable drop in the QoS and hinder the overall robustness and energy efficiency of the network. Interference avoidance mechanisms, such as frequency hopping techniques, reduce the need for retransmissions due to interferences but they are often tailored to specific scenarios and are not easily adapted to other use cases. On the other hand, the total absence of interference avoidance mechanisms introduces a security risk because the communication channel may be intentionally attacked and interfered with to hinder or totally block it. In this paper we propose a method for supporting the design of communication solutions under dynamic channel interference conditions and we implement dynamic management policies for frequency hopping technique and channel selection at runtime. The method considers several standard frequency hopping techniques and quality metrics, and the quality and status of the available frequency channels to propose the best combined solution to minimize the side effects of interferences. A simulation tool has been developed and used in this work to validate the method. PMID:29473910

A Method for Dynamically Selecting the Best Frequency Hopping Technique in Industrial Wireless Sensor Network Applications.

PubMed

Fernández de Gorostiza, Erlantz; Berzosa, Jorge; Mabe, Jon; Cortiñas, Roberto

2018-02-23

Industrial wireless applications often share the communication channel with other wireless technologies and communication protocols. This coexistence produces interferences and transmission errors which require appropriate mechanisms to manage retransmissions. Nevertheless, these mechanisms increase the network latency and overhead due to the retransmissions. Thus, the loss of data packets and the measures to handle them produce an undesirable drop in the QoS and hinder the overall robustness and energy efficiency of the network. Interference avoidance mechanisms, such as frequency hopping techniques, reduce the need for retransmissions due to interferences but they are often tailored to specific scenarios and are not easily adapted to other use cases. On the other hand, the total absence of interference avoidance mechanisms introduces a security risk because the communication channel may be intentionally attacked and interfered with to hinder or totally block it. In this paper we propose a method for supporting the design of communication solutions under dynamic channel interference conditions and we implement dynamic management policies for frequency hopping technique and channel selection at runtime. The method considers several standard frequency hopping techniques and quality metrics, and the quality and status of the available frequency channels to propose the best combined solution to minimize the side effects of interferences. A simulation tool has been developed and used in this work to validate the method.

Total Ambient Dose Equivalent Buildup Factor Determination for Nbs04 Concrete.

PubMed

Duckic, Paulina; Hayes, Robert B

2018-06-01

Buildup factors are dimensionless multiplicative factors required by the point kernel method to account for scattered radiation through a shielding material. The accuracy of the point kernel method is strongly affected by the correspondence of analyzed parameters to experimental configurations, which is attempted to be simplified here. The point kernel method has not been found to have widespread practical use for neutron shielding calculations due to the complex neutron transport behavior through shielding materials (i.e. the variety of interaction mechanisms that neutrons may undergo while traversing the shield) as well as non-linear neutron total cross section energy dependence. In this work, total ambient dose buildup factors for NBS04 concrete are calculated in terms of neutron and secondary gamma ray transmission factors. The neutron and secondary gamma ray transmission factors are calculated using MCNP6™ code with updated cross sections. Both transmission factors and buildup factors are given in a tabulated form. Practical use of neutron transmission and buildup factors warrants rigorously calculated results with all associated uncertainties. In this work, sensitivity analysis of neutron transmission factors and total buildup factors with varying water content has been conducted. The analysis showed significant impact of varying water content in concrete on both neutron transmission factors and total buildup factors. Finally, support vector regression, a machine learning technique, has been engaged to make a model based on the calculated data for calculation of the buildup factors. The developed model can predict most of the data with 20% relative error.

Mechanical Design of High Lift Systems for High Aspect Ratio Swept Wings

NASA Technical Reports Server (NTRS)

Rudolph, Peter K. C.

1998-01-01

The NASA Ames Research Center is working to develop a methodology for the optimization and design of the high lift system for future subsonic airliners with the involvement of two partners. Aerodynamic analysis methods for two dimensional and three dimensional wing performance with flaps and slats deployed are being developed through a grant with the aeronautical department of the University of California Davis, and a flap and slat mechanism design procedure is being developed through a contract with PKCR, Inc., of Seattle, WA. This report documents the work that has been completed in the contract with PKCR on mechanism design. Flap mechanism designs have been completed for seven (7) different mechanisms with a total of twelve (12) different layouts all for a common single slotted flap configuration. The seven mechanisms are as follows: Simple Hinge, Upside Down/Upright Four Bar Linkage (two layouts), Upside Down Four Bar Linkages (three versions), Airbus A330/340 Link/Track Mechanism, Airbus A320 Link/Track Mechanism (two layouts), Boeing Link/Track Mechanism (two layouts), and Boeing 767 Hinged Beam Four Bar Linkage. In addition, a single layout has been made to investigate the growth potential from a single slotted flap to a vane/main double slotted flap using the Boeing Link/Track Mechanism. All layouts show Fowler motion and gap progression of the flap from stowed to a fully deployed position, and evaluations based on spanwise continuity, fairing size and number, complexity, reliability and maintainability and weight as well as Fowler motion and gap progression are presented. For slat design, the options have been limited to mechanisms for a shallow leading edge slat. Three (3) different layouts are presented for maximum slat angles of 20 deg, 15 deg and 1O deg all mechanized with a rack and pinion drive similar to that on the Boeing 757 airplane. Based on the work of Ljungstroem in Sweden, this type of slat design appears to shift the lift curve so that higher lift is achieved with the deployed slat with no increase in angle of attack. The layouts demonstrate that these slat systems can be designed with no need for slave links, and an experimental test program is outlined to experimentally validate the lift characteristics of the shallow slat.

Motivation and Justice at Work: The Role of Emotion and Cognition Components of Personal and Collective Work Identity

PubMed Central

Nordhall, Ola; Knez, Igor

2018-01-01

The aim of this study was to investigate the role of personal and collective work identity (including emotion and cognition components), in predicting work motivation (operationalized as work self-determined motivation) and organizational justice (operationalized as organizational pay justice). Digitized questionnaires were distributed by e-mail to 2905 members, teachers, of a Swedish trade union. A total of 768 individuals answered the questionnaire and by that participated in this study. Personal- compared to collective work identity was shown to positively associate with self-determined motivation accounted for by the emotion component of personal work identity. Collective compared to personal work identity was reported to positively associate with organizational pay justice accounted for by the cognition component of collective work identity. All this suggests that both work-related motivation and organizational justice might be, to some extent, accounted for by the psychological mechanisms of work identity and that, as predicted, different types of work identity, play different significant roles in predicting motivation and justice at work. More precisely, the emotion component of work identity was more pronounced in personal work-bonding relationships, and the cognitive component, of work identity in contrast, was more pronounced in collective work-bonding relationships. PMID:29379454

Motivation and Justice at Work: The Role of Emotion and Cognition Components of Personal and Collective Work Identity.

PubMed

Nordhall, Ola; Knez, Igor

2017-01-01

The aim of this study was to investigate the role of personal and collective work identity (including emotion and cognition components), in predicting work motivation (operationalized as work self-determined motivation) and organizational justice (operationalized as organizational pay justice). Digitized questionnaires were distributed by e-mail to 2905 members, teachers, of a Swedish trade union. A total of 768 individuals answered the questionnaire and by that participated in this study. Personal- compared to collective work identity was shown to positively associate with self-determined motivation accounted for by the emotion component of personal work identity. Collective compared to personal work identity was reported to positively associate with organizational pay justice accounted for by the cognition component of collective work identity. All this suggests that both work-related motivation and organizational justice might be, to some extent, accounted for by the psychological mechanisms of work identity and that, as predicted, different types of work identity, play different significant roles in predicting motivation and justice at work. More precisely, the emotion component of work identity was more pronounced in personal work-bonding relationships, and the cognitive component, of work identity in contrast, was more pronounced in collective work-bonding relationships.

Age differences in coping and locus of control: a study of managerial stress in Hong Kong.

PubMed

Siu, O; Cooper, C L; Spector, P E; Donald, I

2001-12-01

The present study involved data collection from 3 samples of Hong Kong managers to examine mechanisms by which age would relate to work well-being. A total of 634 managers was drawn by random sampling and purposive sampling methods. The results showed that age was positively related to well-being (job satisfaction and mental well-being). Furthermore, older managers reported fewer sources of stress, better coping, and a more internal locus of control. Multiple regression analyses suggested that the relations of age with 2 well-being indicators can be attributed to various combinations of coping, work locus of control, sources of stress, managerial level, and organizational tenure.

Increased mechanical cost of walking in children with diplegia: the role of the passenger unit cannot be neglected.

PubMed

Van de Walle, P; Hallemans, A; Truijen, S; Gosselink, R; Heyrman, L; Molenaers, G; Desloovere, K

2012-01-01

Gait efficiency in children with cerebral palsy is decreased. To date, most research did not include the upper body as a separate functional unit when exploring these changes in gait efficiency. Since children with spastic diplegia often experience problems with trunk control, they could benefit from separate evaluation of the so-called 'passenger unit'. Therefore, the aim of the current study was to improve insights in the role of the passenger unit in decreased gait efficiency in children with diplegia. Mechanical cost of walking was investigated by calculating work by the integrated joint power approach in 18 children with diplegia and 25 age-related typical developing controls. The total mechanical work in children with diplegia was 1.5 times higher than in typical children. In children with diplegia work at the lower limbs was increased by 37% compared to typical children. Substantially higher increases, up to 222%, were noted at the passenger unit. Trunk and head were the main contributors to the increased work of the passenger unit, but the role of the arms cannot be neglected. Due to these disproportional increases in locomotor and passenger unit, the demands of the passenger unit in pathological gait can no longer be considered minor, as in typical gait. Therefore, the role of the passenger unit must be recognized in the decrease of gait efficiency in children with spastic diplegia and should be part of the evaluation of gait efficiency in clinical practice. Copyright © 2012 Elsevier Ltd. All rights reserved.

Work-related fatal injuries in Brescia County (Northern Italy), 1982 to 2015: A forensic analysis.

PubMed

Perotti, Silvia; Russo, Maria Cristina

2018-06-06

Work-related deaths represent an important social problem. We report all the occupational fatal injuries recorded by the Brescia Institute of Forensic Medicine from 1982 to 2015. A total of 426 post-mortem examinations due to accidental work injuries were retrospectively analysed according to temporal distribution (year, month and day of the workplace accident); workers' characteristics (sex, age, nationality); type of occupation; cause of death; anatomical region of fatal injuries and timing of death. The accidental occupational events occurred with a mean of 12.5 cases per year. Almost all the workers were male (99%) and Italians (87%), aged between 35 and 49 years old (34.27%). The occupation with more fatalities was construction (36.62%), followed by mechanical industry (19.25%) and agriculture (13.15%). Most of deaths were connected to a mechanical trauma (77.69%) such as falls, machinery-related events, blunt forces or explosions. The predominant site of the lethal wound was the head (33.56%), with a high percentage of death resulting from a traumatic brain injury. In 30.75% of cases death occurred after a short period of hospitalization. Copyright © 2018 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

In vivo performance of an acellular disc-like angle ply structure (DAPS) for total disc replacement in a small animal model.

PubMed

Martin, John T; Kim, Dong Hwa; Milby, Andrew H; Pfeifer, Christian G; Smith, Lachlan J; Elliott, Dawn M; Smith, Harvey E; Mauck, Robert L

2017-01-01

Total intervertebral disc replacement with a biologic engineered disc may be an alternative to spinal fusion for treating end-stage disc disease. In previous work, we developed disc-like angle ply structures (DAPS) that replicate the structure and function of the native disc and a rat tail model to evaluate DAPS in vivo. Here, we evaluated a strategy in which, after in vivo implantation, endogenous cells could colonize the acellular DAPS and form an extracellular matrix organized by the DAPS topographical template. To do so, acellular DAPS were implanted into the caudal spines of rats and evaluated over 12 weeks by mechanical testing, histology, and microcomputed tomography. An external fixation device was used to stabilize the implant site and various control groups were included to evaluate the effect of immobilization. There was robust tissue formation within the DAPS after implantation and compressive mechanical properties of the implant matched that of the native motion segment. Immobilization provided a stable site for fibrous tissue formation after either a discectomy or a DAPS implantation, but bony fusion eventually resulted, with segments showing intervertebral bridging after long-term implantation, a process that was accelerated by the implanted DAPS. Thus, while compressive mechanical properties were replicated after DAPS implantation, methods to actively prevent fusion must be developed. Future work will focus on limiting fusion by remobilizing the motion segment after a period of integration, delivering pro-chondrogenic factors, and pre-seeding DAPS with cells prior to implantation. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:23-31, 2017. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Breaststroke swimmers moderate internal work increases toward the highest stroke frequencies.

PubMed

Lauer, Jessy; Olstad, Bjørn Harald; Minetti, Alberto Enrico; Kjendlie, Per-Ludvik; Rouard, Annie Hélène

2015-09-18

A model to predict the mechanical internal work of breaststroke swimming was designed. It allowed us to explore the frequency-internal work relationship in aquatic locomotion. Its accuracy was checked against internal work values calculated from kinematic sequences of eight participants swimming at three different self-chosen paces. Model predictions closely matched experimental data (0.58 ± 0.07 vs 0.59 ± 0.05 J kg(-1)m(-1); t(23)=-0.30, P=0.77), which was reflected in a slope of the major axis regression between measured and predicted total internal work whose 95% confidence intervals included the value of 1 (β=0.84, [0.61, 1.07], N=24). The model shed light on swimmers ability to moderate the increase in internal work at high stroke frequencies. This strategy of energy minimization has never been observed before in humans, but is present in quadrupedal and octopedal animal locomotion. This was achieved through a reduced angular excursion of the heaviest segments (7.2 ± 2.9° and 3.6 ± 1.5° for the thighs and trunk, respectively, P<0.05) in favor of the lightest ones (8.8 ± 2.3° and 7.4 ± 1.0° for the shanks and forearms, respectively, P<0.05). A deeper understanding of the energy flow between the body segments and the environment is required to ascertain the possible dependency between internal and external work. This will prove essential to better understand swimming mechanical cost determinants and power generation in aquatic movements. Copyright © 2015 Elsevier Ltd. All rights reserved.

Magnetic properties of Fe-Si steel depending on compressive and tensile stresses under sinusoidal and distorted excitations

NASA Astrophysics Data System (ADS)

Permiakov, V.; Pulnikov, A.; Dupré, L.; De Wulf, M.; Melkebeek, J.

2003-05-01

In this article, the magnetic properties of nonoriented electrical steel under sinusoidal and distorted excitations are investigated for the whole range of unidirectional mechanical stresses. The distorted flux obtained from the tooth tip of 3 kW induction machine at no-load test was put into the measurement system. The total losses increase for compressive stress both under sinusoidal and distorted excitations. For tensile elastic stresses, the total losses first decrease and then increase in a very similar way for both excitations. In contrast, the difference between total losses under sinusoidal and distorted magnetic fluxes becomes smaller with increase of the plastic strain. This work is a serious step toward complete characterization of the magnetic properties of electrical steel in the teeth area of induction machines. A deeper insight of that problem can improve the design of induction machines and other electromagnetic devices.

Failure mechanisms and lifetime prediction methodology for polybutylene pipe in water distribution system

NASA Astrophysics Data System (ADS)

Niu, Xiqun

Polybutylene (PB) is a semicrystalline thermoplastics. It has been widely used in potable water distribution piping system. However, field practice shows that failure occurs much earlier than the expected service lifetime. What are the causes and how to appropriately evaluate its lifetime motivate this study. In this thesis, three parts of work have been done. First is the understanding of PB, which includes material thermo and mechanical characterization, aging phenomena and notch sensitivity. The second part analyzes the applicability of the existing lifetime testing method for PB. It is shown that PB is an anomaly in terms of the temperature-lifetime relation because of the fracture mechanism transition across the testing temperature range. The third part is the development of the methodology of lifetime prediction for PB pipe. The fracture process of PB pipe consists of three stages, i.e., crack initiation, slow crack growth (SCG) and crack instability. The practical lifetime of PB pipe is primarily determined by the duration of the first two stages. The mechanism of crack initiation and the quantitative estimation of the time to crack initiation are studied by employing environment stress cracking technique. A fatigue slow crack growth testing method has been developed and applied in the study of SCG. By using Paris-Erdogan equation, a model is constructed to evaluate the time for SCG. As a result, the total lifetime is determined. Through this work, the failure mechanisms of PB pipe has been analyzed and the lifetime prediction methodology has been developed.

[A sign of the rotational impact of the gunshot projectile on the flat bone].

PubMed

Leonov, S V

2014-01-01

The objective of the present work was to study the mechanisms of formation of the gunshot fracture of the flat bones with special reference to the translational and rotational motion of the projectile. A total of 120 real and experimental injuries of this type were available for the investigation with the use of simulation by the finite-elemental analysis. A set of morphological features has been identified that make it possible to determine the direction of rotation of the gunshot projectile.

Solar radiation effects on glasses

NASA Technical Reports Server (NTRS)

Kinser, Donald L.

1994-01-01

This work was begun in 1978 under NASA grant NAS8-32695 which prepared the samples that were included in the assemblage of samples on LDEF which was placed in earth orbit by Challenger crew members during mission 41C on April 1984. Those samples, recovered in February 1990, were exposed to earth orbit environment for a total of approximately 5.8 years. Following their recovery the optical and mechanical properties were characterized and sample surfaces were examined so as to characterize micrometeorite impact sites.

Numerical Implementation of a Multiple-ISV Thermodynamically-Based Work Potential Theory for Modeling Progressive Damage and Failure in Fiber-Reinforced Laminates

NASA Technical Reports Server (NTRS)

Pineda, Evan J.; Waas, Anthony M.

2011-01-01

A thermodynamically-based work potential theory for modeling progressive damage and failure in fiber-reinforced laminates is presented. The current, multiple-internal state variable (ISV) formulation, enhanced Schapery theory (EST), utilizes separate ISVs for modeling the effects of damage and failure. Damage is considered to be the effect of any structural changes in a material that manifest as pre-peak non-linearity in the stress versus strain response. Conversely, failure is taken to be the effect of the evolution of any mechanisms that results in post-peak strain softening. It is assumed that matrix microdamage is the dominant damage mechanism in continuous fiber-reinforced polymer matrix laminates, and its evolution is controlled with a single ISV. Three additional ISVs are introduced to account for failure due to mode I transverse cracking, mode II transverse cracking, and mode I axial failure. Typically, failure evolution (i.e., post-peak strain softening) results in pathologically mesh dependent solutions within a finite element method (FEM) setting. Therefore, consistent character element lengths are introduced into the formulation of the evolution of the three failure ISVs. Using the stationarity of the total work potential with respect to each ISV, a set of thermodynamically consistent evolution equations for the ISVs is derived. The theory is implemented into commercial FEM software. Objectivity of total energy dissipated during the failure process, with regards to refinements in the FEM mesh, is demonstrated. The model is also verified against experimental results from two laminated, T800/3900-2 panels containing a central notch and different fiber-orientation stacking sequences. Global load versus displacement, global load versus local strain gage data, and macroscopic failure paths obtained from the models are compared to the experiments.

A Thermodynamically-Based Mesh Objective Work Potential Theory for Predicting Intralaminar Progressive Damage and Failure in Fiber-Reinforced Laminates

NASA Technical Reports Server (NTRS)

Pineda, Evan J.; Waas, Anthony M.

2012-01-01

A thermodynamically-based work potential theory for modeling progressive damage and failure in fiber-reinforced laminates is presented. The current, multiple-internal state variable (ISV) formulation, enhanced Schapery theory (EST), utilizes separate ISVs for modeling the effects of damage and failure. Damage is considered to be the effect of any structural changes in a material that manifest as pre-peak non-linearity in the stress versus strain response. Conversely, failure is taken to be the effect of the evolution of any mechanisms that results in post-peak strain softening. It is assumed that matrix microdamage is the dominant damage mechanism in continuous fiber-reinforced polymer matrix laminates, and its evolution is controlled with a single ISV. Three additional ISVs are introduced to account for failure due to mode I transverse cracking, mode II transverse cracking, and mode I axial failure. Typically, failure evolution (i.e., post-peak strain softening) results in pathologically mesh dependent solutions within a finite element method (FEM) setting. Therefore, consistent character element lengths are introduced into the formulation of the evolution of the three failure ISVs. Using the stationarity of the total work potential with respect to each ISV, a set of thermodynamically consistent evolution equations for the ISVs is derived. The theory is implemented into commercial FEM software. Objectivity of total energy dissipated during the failure process, with regards to refinements in the FEM mesh, is demonstrated. The model is also verified against experimental results from two laminated, T800/3900-2 panels containing a central notch and different fiber-orientation stacking sequences. Global load versus displacement, global load versus local strain gage data, and macroscopic failure paths obtained from the models are compared to the experiments.

Correlation between mechanical and chemical degradation after outdoor and accelerated laboratory aging for multilayer photovoltaic backsheets

NASA Astrophysics Data System (ADS)

Lin, Chiao-Chi; Lyu, Yadong; Yu, Li-Chieh; Gu, Xiaohong

2016-09-01

Channel cracking fragmentation testing and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy were utilized to study mechanical and chemical degradation of a multilayered backsheet after outdoor and accelerated laboratory aging. A model sample of commercial PPE backsheet, namely polyethylene terephthalate/polyethylene terephthalate/ethylene vinyl acetate (PET/PET/EVA) was investigated. Outdoor aging was performed in Gaithersburg, Maryland, USA for up to 510 days, and complementary accelerated laboratory aging was conducted on the NIST (National Institute of Standards and Technology) SPHERE (Simulated Photodegradation via High Energy Radiant Exposure). Fracture energy, mode I stress intensity factor and film strength were analyzed using an analytical model based on channel cracking fragmentation testing results. The correlation between mechanical and chemical degradation was discussed for both outdoor and accelerated laboratory aging. The results of this work provide preliminary understanding on failure mechanism of backsheets after weathering, laying the groundwork for linking outdoor and indoor accelerated laboratory testing for multilayer photovoltaic backsheets.

Teachers’ work ability: a study of relationships between collective efficacy and self-efficacy beliefs

PubMed Central

Guidetti, Gloria; Viotti, Sara; Bruno, Andreina; Converso, Daniela

2018-01-01

Introduction Work ability constitutes one of the most studied well-being indicators related to work. Past research highlighted the relationship with work-related resources and demands, and personal resources. However, no studies highlight the role of collective and self-efficacy beliefs in sustaining work ability. Purpose The purpose of this study was to examine whether and by which mechanism work ability is linked with individual and collective efficacies in a sample of primary and middle school teachers. Materials and methods Using a dataset consisting of 415 primary and middle school Italian teachers, the analysis tested for the mediating role of self-efficacy between collective efficacy and work ability. Results Mediational analysis highlights that teachers’ self-efficacy totally mediates the relationship between collective efficacy and perceived work ability. Conclusion Results of this study enhance the theoretical knowledge and empirical evidence regarding the link between teachers’ collective efficacy and self-efficacy, giving further emphasis to the concept of collective efficacy in school contexts. Moreover, the results contribute to the study of well-being in the teaching profession, highlighting a process that sustains and promotes levels of work ability through both collective and personal resources. PMID:29861646

Mechanics and geometry in the seashell-like (Turritella) surface

NASA Astrophysics Data System (ADS)

Guo, Qiaohang; Chen, Zi; Li, Wei; Ren, Kun; Lin, Junjie; Taber, Larry A.; Chen, Wenzhe

2013-03-01

Helical structures are ubiquitous in nature and engineering, ranging from DNA molecules to plant tendrils, from sea snail shells to nanoribbons. While the helical shapes in natural and engineered systems often exhibit nearly uniform radius and pitch, helical shell structures with changing radius and pitch, such as seashells and some plant tendrils, adds to the variety of this family of aesthetic beauty. Here we report the first biomimetic seashell-like structure resulting from mechanics of geometric frustration. In previous studies, the total potential energy is everywhere minimized when the system achieves an equilibrium. In this study, however, the local energy minimization cannot be realized because of the geometric incompatibility, and hence the whole system deforms into a shape with a global energy minimum whereby the energy in each segment may not necessary be locally optimized. This novel approach can be applied to develop materials and systems with desirable geometries by exploiting mechanics of geometric frustration. The authors would like to thank Yushan Huang, Zhen Liu, Si Chen for their assistance in the experimental demonstration. This work has been in part supported by NSFC (Grant No.11102040 and No.11201001044), the Sigma Xi Grants-in-Aid of Research (GIAR) program, American Academy of Mechanics Founder's Award from the Robert M. and Mary Haythornthwaite Foundation, and Society in Science, The Branco Weiss Fellowship, administered by ETH Zurich. Qiaohang Guo and Zi Chen contributed equally to this work.

A coupled piezoelectric-electromagnetic energy harvesting technique for achieving increased power output through damping matching

NASA Astrophysics Data System (ADS)

Challa, Vinod R.; Prasad, M. G.; Fisher, Frank T.

2009-09-01

Vibration energy harvesting is being pursued as a means to power wireless sensors and ultra-low power autonomous devices. From a design standpoint, matching the electrical damping induced by the energy harvesting mechanism to the mechanical damping in the system is necessary for maximum efficiency. In this work two independent energy harvesting techniques are coupled to provide higher electrical damping within the system. Here the coupled energy harvesting device consists of a primary piezoelectric energy harvesting device to which an electromagnetic component is added to better match the total electrical damping to the mechanical damping in the system. The first coupled device has a resonance frequency of 21.6 Hz and generates a peak power output of ~332 µW, compared to 257 and 244 µW obtained from the optimized, stand-alone piezoelectric and electromagnetic energy harvesting devices, respectively, resulting in a 30% increase in power output. A theoretical model has been developed which closely agrees with the experimental results. A second coupled device, which utilizes the d33 piezoelectric mode, shows a 65% increase in power output in comparison to the corresponding stand-alone, single harvesting mode devices. This work illustrates the design considerations and limitations that one must consider to enhance device performance through the coupling of multiple harvesting mechanisms within a single energy harvesting device.

Simultaneous Observation of Lightning and Terrestrial Gamma-ray Flashes

NASA Astrophysics Data System (ADS)

Alnussirat, S.; Christian, H. J., Jr.; Fishman, G. J.; Burchfield, J. C.

2017-12-01

The relative timing between TGFs and lightning optical emissions is a critical parameter that may elucidate the production mechanism(s) of TGFs. In this work, we study the correlation between optical emissions detected by the Geostationary Lightning Mapper (GLM) and TGFs triggered by the Fermi-GBM. The GLM is the only instrument that detects total lightning activities (IC and CG) continuously (day and night) over a large area of the Earth, with very high efficiency and location accuracy. The unique optical emission data from the GLM will enable us to study, for the first time, the lightning activity before and after the TGF production. From this investigation, we hope to clarify the production mechanism of TGFs and the characteristics of thundercloud cells that produce them. A description of the GLM concept and operation will be presented and as well as the preliminary results of the TGF-optical emission correlation.

A Variational Method in Out-of-Equilibrium Physical Systems

PubMed Central

Pinheiro, Mario J.

2013-01-01

We propose a new variational principle for out-of-equilibrium dynamic systems that are fundamentally based on the method of Lagrange multipliers applied to the total entropy of an ensemble of particles. However, we use the fundamental equation of thermodynamics on differential forms, considering U and S as 0-forms. We obtain a set of two first order differential equations that reveal the same formal symplectic structure shared by classical mechanics, fluid mechanics and thermodynamics. From this approach, a topological torsion current emerges of the form , where Aj and ωk denote the components of the vector potential (gravitational and/or electromagnetic) and where ω denotes the angular velocity of the accelerated frame. We derive a special form of the Umov-Poynting theorem for rotating gravito-electromagnetic systems. The variational method is then applied to clarify the working mechanism of particular devices. PMID:24316718

Singular structure of Mueller matrices images of biological crystal networks for diagnostic human tissues pathological changes

NASA Astrophysics Data System (ADS)

Sakhnovskiy, M. Y.; Ushenko, V. A.

2013-09-01

The process of converting of laser radiation by optically anisotropic crystals of biological networks are singular in the sense of total (simultaneous) of mechanisms of orientation and phase (birefringence) anisotropy the formation of polarization-inhomogeneous field of scattered radiation. This work is aimed at developing a method of polarization selection mechanisms of blood plasma polycrystalline networks anisotropy. The relationship between statistics, correlation and fractal parameters of polarization-inhomogeneous images of blood plasma and by linear dichroism and linear birefringence of polycrystalline networks albumin and globulin was found. The criteria of differentiation and diagnostic images of polarization-inhomogeneous plasma samples of the control group (donor) and a group of patients with malignant changes of breast tissue was identified.

Update of the NEXT Ion Thruster Service Life Assessment with Post-Test Correlation to the Long Duration Test

NASA Technical Reports Server (NTRS)

Yim, John T.; Soulas, George C.; Shastry, Rohit; Choi, Maria; Mackey, Jonathan A.; Sarver-Verhey, Timothy R.

2017-01-01

The service life assessment for NASA's Evolutionary Xenon Thruster is updated to incorporate the results from the successful and voluntarily early completion of the 51,184 hour long duration test which demonstrated 918 kg of total xenon throughput. The results of the numerous post-test investigations including destructive interrogations have been assessed against all of the critical known and suspected failure mechanisms to update the life and throughput expectations for each major component. Analysis results of two of the most acute failure mechanisms, namely pit-and-groove erosion and aperture enlargement of the accelerator grid, are not updated in this work but will be published at a future time after analysis completion.

Carrier recombination mechanisms and efficiency droop in GaInN/GaN light-emitting diodes

DOE PAGES

Dai, Qi; Shan, Qifeng; Wang, Jing; ...

2010-09-30

In this work, we model the carrier recombination mechanisms in GaInN/GaN light-emitting diodes as R=An+Bn 2+Cn 3+f(n), where f(n) represents carrier leakage out of the active region. The term f(n) is expanded into a power series and shown to have higher-than-third-order contributions to the recombination. The total third-order nonradiative coefficient (which may include an f(n) leakage contribution and an Auger contribution) is found to be 8×10 -29 cm 6 s -1. Finally, comparison of the theoretical ABC+f(n) model with experimental data shows that a good fit requires the inclusion of the f(n) term.

Neural Network Models of Simple Mechanical Systems Illustrating the Feasibility of Accelerated Life Testing

NASA Technical Reports Server (NTRS)

Fusaro, Robert L.; Jones, Steven P.; Jansen, Ralph

1996-01-01

A complete evaluation of the tribological characteristics of a given material/mechanical system is a time-consuming operation since the friction and wear process is extremely systems sensitive. As a result, experimental designs (i.e., Latin Square, Taguchi) have been implemented in an attempt to not only reduce the total number of experimental combinations needed to fully characterize a material/mechanical system, but also to acquire life data for a system without having to perform an actual life test. Unfortunately, these experimental designs still require a great deal of experimental testing and the output does not always produce meaningful information. In order to further reduce the amount of experimental testing required, this study employs a computer neural network model to investigate different material/mechanical systems. The work focuses on the modeling of the wear behavior, while showing the feasibility of using neural networks to predict life data. The model is capable of defining which input variables will influence the tribological behavior of the particular material/mechanical system being studied based on the specifications of the overall system.

Empirical prediction of mechanical properties of flexible pavement through GPR

NASA Astrophysics Data System (ADS)

Bianchini Ciampoli, Luca; Benedetto, Andrea

2017-04-01

To date, it is well known that the frequency of accidental events recorded on a road, is related to the deterioration rate of its pavement. In this sense, the monitoring of the pavement health over a road network is a crucial task for the administrations, to define a priority scale for maintenance works, and accordingly to lower the risk of accidents. Several studies suggest the possibility to employ Ground-penetrating Radar (GPR) to overcome the limits of traditional bearing tests, which due to their low productivity and high costs, can only give a discrete knowledge about the strength of the pavement. This work presents a GPR-based empirical model for the prediction of the bearing capacity of a road pavement, expressed as Young's Modulus. The model exploits the GPR to extract information on the thickness of the base course and the clay content, by referring to the signal velocity and attenuation, respectively. To test the effectiveness of the model, experimental activities have been accounted for. In particular, multi-frequency GPR tests have been performed along road sections of rural roads, composed of a flexible pavement, for a total of 45 Km. As ground-truth, light falling weight deflectometer (LFWD) and Curviameter have been employed. Both the electromagnetic and the mechanical datasets have been properly processed, in order to reduce misinterpretations and to raise the statistical significance of the procedure. Hence, the calibration of the parameters composing the model was run in a subsection, equal to 8% of the total length, randomly selected within the surveyed track. Finally, as validation, the model has been applied to the whole analysed dataset. As a result, the empirical model showed a good effectiveness in predicting the mechanical response of the pavement, with a normalised root mean squared deviation equal to 0.27. Finally, by averaging the measured and predicted mechanical data every 50 m and sorting the results into strength classes, a qualitative approach useful for a visual detection of low-resistance areas has been also proposed. This study demonstrates the efficiency and reliability of GPR in mechanical assessment of flexible pavements. This empirical approach can represent a useful tool for administrations and companies managing road assets, for a non-destructive detection of the areas interested by early stage deterioration processes, and the definition of a priority-based scheduling of maintenance works. Acknowledgements The Authors thank COST, for funding the Action TU1208 "Civil Engineering Applications of Ground Penetrating Radar."

Prone position improves lung mechanical behavior and enhances gas exchange efficiency in mechanically ventilated chronic obstructive pulmonary disease patients.

PubMed

Mentzelopoulos, Spyros D; Zakynthinos, Spyros G; Roussos, Charris; Tzoufi, Maria J; Michalopoulos, Argyris S

2003-06-01

Pronation might favorably affect respiratory system (rs) mechanics and function in volume-controlled, mode-ventilated chronic obstructive pulmonary disease (COPD) patients. We studied 10 COPD patients, initially positioned supine (baseline supine [supine(BAS)]) and then randomly and consecutively changed to protocol supine (supine(PROT)), semirecumbent, and prone positions. Rs mechanics and inspiratory work (W(I)) were assessed at baseline (0.6 L) (all postures) and sigh (1.2 L) (supine(BAS) excluded) tidal volume (V(T)) with rapid airway occlusion during constant-flow inflation. Hemodynamics and gas exchange were assessed in all postures. There were no complications. Prone positioning resulted in (a) increased dynamic-static chest wall (cw) elastance (at both V(Ts)) and improved oxygenation versus supine(BAS), supine(PROT), and semirecumbent, (b) decreased additional lung (L) resistance-elastance versus supine(PROT) and semirecumbent at sigh V(T), (c) decreased L-static elastance (at both V(Ts)) and improved CO(2) elimination versus supine(BAS) and supine(PROT), and (d) improved oxygenation versus all other postures. Semirecumbent positioning increased mainly additional cw-resistance versus supine(BAS) and supine(PROT) at baseline. V(T) W(I)-sub-component changes were consistent with changes in rs, cw, and L mechanical properties. Total rs-W(I) and hemodynamics were unaffected by posture change. After pronation, five patients were repositioned supine (supine(POSTPRO)). In supine(POSTPRO), static rs-L elastance were lower, and oxygenation was still improved versus supine(BAS). Pronation of mechanically ventilated COPD patients exhibits applicability and effectiveness and improves oxygenation and sigh-L mechanics versus semirecumbent ("gold standard") positioning. By assessing respiratory mechanics, inspiratory work, hemodynamics, and gas exchange, we showed that prone positioning of mechanically ventilated chronic obstructed pulmonary disease patients improves oxygenation and lung mechanics during sigh versus semirecumbent positioning. Furthermore, certain pronation-related benefits versus preprone-supine positioning (reduced lung elastance and improved oxygenation) are maintained in the postprone supine position.

Mechanical Prophylaxis after Lower Extremity Total Joint Arthroplasty: A Review.

PubMed

Chughtai, Morad; Newman, Jared M; Solow, Max; Davidson, Iyooh U; Sodhi, Nipun; Gaal, Benjamin; Khlopas, Anton; Sultan, Assem A; Mont, Michael A

2017-12-22

Venous thromboembolism (VTE) is a serious complication that can occur after total hip and knee arthroplasty, and can potentially lead to significant morbidity and even mortality. While various modalities have been used to prevent VTE development, the medications can be associated with a number of adverse events. Therefore, mechanical prophylaxis with pumps and compressive devices has been used more frequently alone, or in combination, with medications. Therefore, the purpose of this study was to review the current literature on mechanical prophylaxis for VTEs after lower extremity total joint arthroplasty. Specifically, we reviewed mechanical prophylaxis after: 1) total hip arthroplasty and 2) total knee arthroplasty.

Optimal healthcare delivery to care homes in the UK: a realist evaluation of what supports effective working to improve healthcare outcomes

PubMed Central

Goodman, Claire; Davies, Sue L; Dening, Tom; Gage, Heather; Meyer, Julienne; Schneider, Justine; Bell, Brian; Jordan, Jake; Martin, Finbarr C; Iliffe, Steve; Bowman, Clive; Gladman, John R F; Victor, Christina; Mayrhofer, Andrea; Handley, Melanie; Zubair, Maria

2018-01-01

Abstract Introduction care home residents have high healthcare needs not fully met by prevailing healthcare models. This study explored how healthcare configuration influences resource use. Methods a realist evaluation using qualitative and quantitative data from case studies of three UK health and social care economies selected for differing patterns of healthcare delivery to care homes. Four homes per area (12 in total) were recruited. A total of 239 residents were followed for 12 months to record resource-use. Overall, 181 participants completed 116 interviews and 13 focus groups including residents, relatives, care home staff, community nurses, allied health professionals and General Practitioners. Results context-mechanism-outcome configurations were identified explaining what supported effective working between healthcare services and care home staff: (i) investment in care home-specific work that legitimises and values work with care homes; (ii) relational working which over time builds trust between practitioners; (iii) care which ‘wraps around’ care homes; and (iv) access to specialist care for older people with dementia. Resource use was similar between sites despite differing approaches to healthcare. There was greater utilisation of GP resource where this was specifically commissioned but no difference in costs between sites. Conclusion activities generating opportunities and an interest in healthcare and care home staff working together are integral to optimal healthcare provision in care homes. Outcomes are likely to be better where: focus and activities legitimise ongoing contact between healthcare staff and care homes at an institutional level; link with a wider system of healthcare; and provide access to dementia-specific expertise. PMID:29315370

Assessment of Blend PVDF Membranes, and the Effect of Polymer Concentration and Blend Composition

PubMed Central

Bamaga, Omar A.; Abdel-Aziz, M. H.

2018-01-01

In this work, PVDF homopolymer was blended with PVDF-co-HFP copolymer and studied in terms of morphology, porosity, pore size, hydrophobicity, permeability, and mechanical properties. Different solvents, namely N-Methyl-2 pyrrolidone (NMP), Tetrahydrofuran (THF), and Dimethylformamide (DMF) solvents, were used to fabricate blended PVDF flat sheet membranes without the introduction of any pore forming agent, through a non-solvent induced phase separation (NIPS) technique. Furthermore, the performance of the fabricated membranes was investigated for pressure and thermal driven applications. The porosity of the membranes was slightly increased with the increase in the overall content of PVDF and by the inclusion of PVDF copolymer. Total PVDF content, copolymer content, and mixed-solvent have a positive effect on mechanical properties. The addition of copolymer increased the hydrophobicity when the total PVDF content was 20%. At 25% and with the inclusion of mixed-solvent, the hydrophobicity was adversely affected. The permeability of the membranes increased with the increase in the overall content of PVDF. Mixed-solvents significantly improved permeability. PMID:29510555

Energy cost and mechanical work of walking during load carriage in soldiers.

PubMed

Grenier, Jordane G; Peyrot, Nicolas; Castells, Josiane; Oullion, Roger; Messonnier, Laurent; Morin, Jean-Benoit

2012-06-01

In the military context, soldiers carry equipments of total mass often exceeding 30%-40% of their body mass (BM) and complexly distributed around their body (backpack, weapons, electronics, protections, etc.), which represents severe load carrying conditions. This study aimed to better understand the effects of load carriage on walking energetics and mechanics during military-type walking. Ten male infantrymen recently retired from the French Foreign Legion performed 3-min walking trials at a constant speed of 4 km·h(-1) on an instrumented treadmill, during which walking pattern spatiotemporal parameters, energy cost (C(W)), external mechanical work (W(ext)), and the work done by one leg against the other during the double-contact period (W(int,dc)) were specifically assessed. Three conditions were tested: (i) light sportswear (SP, reference condition considered as unloaded), (ii) battle equipment (BT, ∼22 kg, ∼27% of subjects' BM, corresponding to a military intermediate load), and (iii) road march equipment (RM, ∼38 kg, ∼46% of subjects' BM, corresponding to a military high load). Repeated-measures ANOVA showed that military equipment carriage significantly (i) altered the spatiotemporal pattern of walking (all P < 0.01), (ii) increased absolute gross and net CW (P < 0.0001), and (iii) increased both absolute and mass-relative W(ext) (P < 0.01) and W(int,dc) (P < 0.0001) but did not alter the inverted pendulum recovery or locomotor efficiency. Military equipments carriage induced significant changes in walking mechanics and energetics, but these effects appeared not greater than those reported with loads carried around the waist and close to the center of mass. This result was not expected because the latter has been hypothesized to be the optimal method of load carriage from a metabolic standpoint.

To flap or not to flap: a discussion between a fish and a jellyfish

NASA Astrophysics Data System (ADS)

Martin, Nathan; Roh, Chris; Idrees, Suhail; Gharib, Morteza

2016-11-01

Fish and jellyfish are known to swim by flapping and by periodically contracting respectively, but which is the more effective propulsion mechanism? In an attempt to answer this question, an experimental comparison is made between simplified versions of these motions to determine which generates the greatest thrust for the least power. The flapping motion is approximated by pitching plates while periodic contractions are approximated by clapping plates. A machine is constructed to operate in either a flapping or a clapping mode between Reynolds numbers 1,880 and 11,260 based on the average plate tip velocity and span. The effect of the total sweep angle, total sweep time, plate flexibility, and duty cycle are investigated. The average thrust generated and power required per cycle are compared between the two modes when their total sweep angle and total sweep time are identical. In general, operating in the clapping mode required significantly more power to generate a similar thrust compared to the flapping mode. However, modifying the duty cycle for clapping caused the effectiveness to approach that of flapping with an unmodified duty cycle. These results suggest that flapping is the more effective propulsion mechanism within the range of Reynolds numbers tested. This work was supported by the Charyk Bio-inspired Laboratory at the California Institute of Technology, the National Science Foundation Graduate Research Fellowship under Grant No. DGE-1144469, and the Summer Undergraduate Research Fellowships program.

Delayed Recall and Working Memory MMSE Domains Predict Delirium following Cardiac Surgery.

PubMed

Price, Catherine C; Garvan, Cynthia; Hizel, Loren P; Lopez, Marcos G; Billings, Frederic T

2017-01-01

Reduced preoperative cognition is a risk factor for postoperative delirium. The significance for type of preoperative cognitive deficit, however, has yet to be explored and could provide important insights into mechanisms and prediction of delirium. Our goal was to determine if certain cognitive domains from the general cognitive screener, the Mini-Mental State Exam (MMSE), predict delirium after cardiac surgery. Patients completed a preoperative MMSE prior to undergoing elective cardiac surgery. Following surgery, delirium was assessed throughout ICU stay using the Confusion Assessment Method for ICU delirium and the Richmond Agitation and Sedation Scale. Cardiac surgery patients who developed delirium (n = 137) had lower total MMSE scores than patients who did not develop delirium (n = 457). In particular, orientation to place, working memory, delayed recall, and language domain scores were lower. Of these, only the working memory and delayed recall domains predicted delirium in a regression model adjusting for history of chronic obstructive pulmonary disease, age, sex, and duration of cardiopulmonary bypass. For each word not recalled on the three-word delayed recall assessment, the odds of delirium increased by 50%. For each item missed on the working memory index, the odds of delirium increased by 36%. Of the patients who developed delirium, 47% had a primary impairment in memory, 21% in working memory, and 33% in both domains. The area under the receiver operating characteristics curve using only the working memory and delayed recall domains was 0.75, compared to 0.76 for total MMSE score. Delirium risk is greater for individuals with reduced MMSE scores on the delayed recall and working memory domains. Research should address why patients with memory and executive vulnerabilities are more prone to postoperative delirium than those with other cognitive limitations.

Correlations between leaf toughness and phenolics among species in contrasting environments of Australia and New Caledonia

PubMed Central

Read, Jennifer; Sanson, Gordon D.; Caldwell, Elizabeth; Clissold, Fiona J.; Chatain, Alex; Peeters, Paula; Lamont, Byron B.; De Garine-Wichatitsky, Michel; Jaffré, Tanguy; Kerr, Stuart

2009-01-01

Background and Aims Plants are likely to invest in multiple defences, given the variety of sources of biotic and abiotic damage to which they are exposed. However, little is known about syndromes of defence across plant species and how these differ in contrasting environments. Here an investigation is made into the association between carbon-based chemical and mechanical defences, predicting that species that invest heavily in mechanical defence of leaves will invest less in chemical defence. Methods A combination of published and unpublished data is used to test whether species with tougher leaves have lower concentrations of phenolics, using 125 species from four regions of Australia and the Pacific island of New Caledonia, in evergreen vegetation ranging from temperate shrubland and woodland to tropical shrubland and rainforest. Foliar toughness was measured as work-to-shear and specific work-to-shear (work-to-shear per unit leaf thickness). Phenolics were measured as ‘total phenolics’ and by protein precipitation (an estimate of tannin activity) per leaf dry mass. Key Results Contrary to prediction, phenolic concentrations were not negatively correlated with either measure of leaf toughness when examined across all species, within regions or within any plant community. Instead, measures of toughness (particularly work-to-shear) and phenolics were often positively correlated in shrubland and rainforest (but not dry forest) in New Caledonia, with a similar trend suggested for shrubland in south-western Australia. The common feature of these sites was low concentrations of soil nutrients, with evidence of P limitation. Conclusions Positive correlations between toughness and phenolics in vegetation on infertile soils suggest that additive investment in carbon-based mechanical and chemical defences is advantageous and cost-effective in these nutrient-deficient environments where carbohydrate may be in surplus. PMID:19098067

Biomechanics and energetics of walking in powered ankle exoskeletons using myoelectric control versus mechanically intrinsic control.

PubMed

Koller, Jeffrey R; Remy, C David; Ferris, Daniel P

2018-05-25

Controllers for assistive robotic devices can be divided into two main categories: controllers using neural signals and controllers using mechanically intrinsic signals. Both approaches are prevalent in research devices, but a direct comparison between the two could provide insight into their relative advantages and disadvantages. We studied subjects walking with robotic ankle exoskeletons using two different control modes: dynamic gain proportional myoelectric control based on soleus muscle activity (neural signal), and timing-based mechanically intrinsic control based on gait events (mechanically intrinsic signal). We hypothesized that subjects would have different measures of metabolic work rate between the two controllers as we predicted subjects would use each controller in a unique manner due to one being dependent on muscle recruitment and the other not. The two controllers had the same average actuation signal as we used the control signals from walking with the myoelectric controller to shape the mechanically intrinsic control signal. The difference being the myoelectric controller allowed step-to-step variation in the actuation signals controlled by the user's soleus muscle recruitment while the timing-based controller had the same actuation signal with each step regardless of muscle recruitment. We observed no statistically significant difference in metabolic work rate between the two controllers. Subjects walked with 11% less soleus activity during mid and late stance and significantly less peak soleus recruitment when using the timing-based controller than when using the myoelectric controller. While walking with the myoelectric controller, subjects walked with significantly higher average positive and negative total ankle power compared to walking with the timing-based controller. We interpret the reduced ankle power and muscle activity with the timing-based controller relative to the myoelectric controller to result from greater slacking effects. Subjects were able to be less engaged on a muscle level when using a controller driven by mechanically intrinsic signals than when using a controller driven by neural signals, but this had no affect on their metabolic work rate. These results suggest that the type of controller (neural vs. mechanical) is likely to affect how individuals use robotic exoskeletons for therapeutic rehabilitation or human performance augmentation.

Catchment Dispersion Mechanisms in an Urban Context

NASA Astrophysics Data System (ADS)

Gironas, J. A.; Mejia, A.; Rossel, F.; Rinaldo, A.; Rodriguez, F.

2014-12-01

Dispersion mechanisms have been examined in-depth in natural catchments in previous studies. However, these dispersion mechanisms have been studied little in urban catchments, where artificial transport elements and morphological arrangements are expected to modify travel times and mobilize excess rainfall from spatially distributed impervious sites. Thus, these features can modify the variance of the catchment's travel times and hence the total dispersion. This work quantifies the dispersion mechanisms in an urban catchment using the theory of transport by travel times as represented by the Urban Morpho-climatic Instantaneous Unit Hydrograph (U-McIUH) model. This model computes travel times based on kinematic wave theory and accounts explicitly for the path heterogeneities and altered connectivity patterns characteristic of an urban drainage network. The analysis is illustrated using the Aubinière urban catchment (France) as a case study. We found that kinematic dispersion is dominant for small rainfall intensities, whereas geomorphologic dispersion becomes more dominant for larger intensities. The total dispersion scales with the drainage area in a power law fashion. The kinematic dispersion is dominant across spatial scales up to a threshold of approximately 2-3 km2, after which the geomorphologic dispersion becomes more dominant. Overall, overland flow is responsible for most of the dispersion, while conduits tend to counteract the increase of the geomorphologic dispersion with a negative kinematic dispersion. Further studies with other catchments are needed to assess whether the latter is a general feature of urban drainage networks.

Spatial characterization of catchment dispersion mechanisms in an urban context

NASA Astrophysics Data System (ADS)

Rossel, Florian; Gironás, Jorge; Mejía, Alfonso; Rinaldo, Andrea; Rodriguez, Fabrice

2014-12-01

Previous studies have examined in-depth the dispersion mechanisms in natural catchments. In contrast, these dispersion mechanisms have been studied little in urban catchments, where artificial transport elements and morphological arrangements are expected to modify travel times and mobilize excess rainfall from spatially distributed impervious sites. This has the ability to modify the variance of the catchment's travel times and hence the total dispersion. This work quantifies the dispersion mechanisms in an urban catchment using the theory of transport by travel times as represented by the Urban Morpho-climatic Instantaneous Unit Hydrograph (U-McIUH) model. The U-McIUH computes travel times based on kinematic wave theory and accounts explicitly for the path heterogeneities and altered connectivity patterns characteristic of an urban drainage network. The analysis is illustrated using the Aubinière urban catchment in France as a case study. We found that kinematic dispersion is dominant for small rainfall intensities, whereas geomorphologic dispersion becomes more dominant for larger intensities. The total dispersion scales with the drainage area in a power law fashion. The kinematic dispersion is dominant across spatial scales up to a threshold of approximately 2-3 km2, after which the geomorphologic dispersion becomes more dominant. Overall, overland flow is responsible for most of the dispersion in the catchment, while conduits tend to counteract the increase of the geomorphologic dispersion with a negative kinematic dispersion. Further study with other catchments is needed to asses if the latter is a general feature of urban drainage networks.

29 CFR 516.23 - Employees of hospitals and residential care facilities compensated for overtime work on the basis...

Code of Federal Regulations, 2010 CFR

2010-07-01

... employee's 14-day work period begins, (2) Hours worked each workday and total hours worked each 14-day work period, (3) Total straight-time wages paid for hours worked during the 14-day period, (4) Total overtime excess compensation paid for hours worked in excess of 8 in a workday and 80 in the work period. (b) A...

A qualitative assessment of safe work practices in logging in the southern United States.

PubMed

Conway, Sadie H; Pompeii, Lisa A; Casanova, Vanessa; Douphrate, David I

2017-01-01

The logging industry is recognized as one of the most dangerous professions in the U.S., but little is known about safety management practices on remote logging sites. A total of six focus group sessions were held among logging supervisors and front line crew members in Arkansas, Louisiana, and Texas (N = 27 participants). Participants perceived that logging was a dangerous profession, but its risks had been mitigated in several ways, most notably through mechanization of timber harvesting. Log trucking-related incidents were widely identified as the primary source of risk for injury and death on logging work sites. Human error, in general, and being out of the machinery on the work site were highlighted as additional sources of risk. Participants indicated high levels of personal motivation to work in a safe manner but tended to underestimate workplace hazards and expressed widely varying levels of co-worker trust. Am. J. Ind. Med. 60:58-68, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

The effect of temperature and drawing ratio on the mechanical properties of polypropylene monofilaments

NASA Astrophysics Data System (ADS)

Taheri, Hesam; Nóbrega, João Miguel; Samyn, Pieter; Covas, José Antonio

2014-05-01

In this work, the simultaneous effect of both temperature and drawing ratio during processing of polypropylene monofilaments has been investigated. The basis of this work specifically aims at emphasizing the conditions of temperature and drawing ratio applied in the cooling bath, in order to find out under which conditions the named parameters can be applied in a processing line under continuous extrusion. The effects of temperature are studied for a constant total drawing ratio to analyze the influences on mechanical properties and structural differences of the final polypropylene monofilament. The quenched monofilaments were drawn around an adjustable guide assembly in the quench bath and first drawing stage, imparting thermal and mechanical treatments to the filaments. In the heating stage, monofilaments are affected to high-speed draw rolls while passing through the oven. As such, the best conditions to produce a polypropylene monofilament with high tenacity strength were determined. Results of this study show that the monofilament properties are significantly affected by temperature in the cooling zone. The nature of the first drawing had a significant effect on the end properties and monofilaments with modulus of 637 MPa have finally been manufactured. We have also proposed a new hypothesis, which is termed "gap nucleation" and determine this phenomenon in the gap between die and cooling bath.

Mechanical, Electronic and Optical Properties of Two Phases of NbB4: First-Principles Calculations

NASA Astrophysics Data System (ADS)

Yang, Ruike; Ma, Shaowei; Wei, Qun; Zhang, Dongyun

2018-05-01

As transition metal borides have been successfully synthesised, the study of the combination of transition metal and boron is another effective way to investigate the properties of boride. We have predicted the novel phase Amm2-NbB4. Using the Cambridge Serial Total Energy Package (CASTEP) code, we further researched on the mechanical, electronic and optical properties of C2/c- and Amm2-NbB4. It is found that both the phases of NbB4 are dynamically and mechanically stable at 0 and 100 GPa. Their Vickers hardness values are both 34 GPa, which indicate that they are hard materials. The band gap of C2/c-NbB4 is 0.145 eV, which indicates that it is a semiconductor (or metalloid) at 0 GPa. For the Amm2-NbB4, the band structure without band gap indicates it is a metal at 0 GPa. The optical properties of these two structures are similar. At 0 eV, the real part of dielectric function is 28.8 for C2/c-NbB4, and the real part value for Amm2-NbB4 is 43. We hope our work will provide some help to the experimental work about the technology of the material.

Estimation of the cost of electro-mechanical equipment for small hydropower plants - review and comparison of methods

NASA Astrophysics Data System (ADS)

Lipiński, Seweryn; Olkowski, Tomasz

2017-10-01

The estimate of the cost of electro-mechanical equipment for new small hydropower plants most often amounts to about 30-40% of the total budget. In case of modernization of existing installations, this estimation represents the main cost. This matter constitutes a research problem for at least few decades. Many models have been developed for that purpose. The aim of our work was to collect and analyse formulas that allow estimation of the cost of investment in electro-mechanical equipment for small hydropower plants. Over a dozen functions were analysed. To achieve the aim of our work, these functions were converted into the form allowing their comparison. Then the costs were simulated with respect to plants' powers and net heads; such approach is novel and allows deeper discussion of the problem, as well as drawing broader conclusions. The following conclusions can be drawn: significant differences in results obtained by using various formulas were observed; there is a need for a wide study based on national investments in small hydropower plants that would allow to develop equations based on local data; the obtained formulas would let to determinate the costs of modernization or a new construction of small hydropower plant more precisely; special attention should be payed to formulas considering turbine type.

The Time-Varying Relationship between Mortality and Business Cycles in the USA.

PubMed

Lam, Jean-Paul; Piérard, Emmanuelle

2017-02-01

We examine the relationship between total mortality, deaths due to motor vehicle accidents, cardiovascular disease and measures of business cycles for the USA, using a time-varying parameter model for the periods 1961-2010. We first present a theoretical model to outline the transmission mechanism from business cycles to health status, to motivate our empirical framework and to explain why the relationship between mortality and the economy may have changed over time. We find overwhelming evidence of structural breaks in the relationship between mortality and business cycles over the sample period. Overall, the relationship between total mortality, cardiovascular mortality and the economy has become less procyclical over time and even countercyclical in recent times for certain age groups. Deaths due to motor vehicle accidents have remained strongly procyclical. Using drugs and medical patent data and data on hours worked, we argue that important advances in medical technology and changes in the effects that working hours have on health are important reasons for this time-varying relationship. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

A gender approach to work ability and its relationship to professional and domestic work hours among nursing personnel.

PubMed

Rotenberg, Lúcia; Portela, Luciana Fernandes; Banks, Bahby; Griep, Rosane Harter; Fischer, Frida Marina; Landsbergis, Paul

2008-09-01

The association between working hours and work ability was examined in a cross-sectional study of male (N=156) and female (N=1092) nurses in three public hospitals. Working hours were considered in terms of their professional and domestic hours per week and their combined impact; total work load. Logistic regression analysis showed a significant association between total work load and inadequate work ability index (WAI) for females only. Females reported a higher proportion of inadequate WAI, fewer professional work hours but longer domestic work hours. There were no significant differences in total work load by gender. The combination of professional and domestic work hours in females seemed to best explain their lower work ability. The findings suggest that investigations into female well-being need to consider their total work load. Our male sample may have lacked sufficient power to detect a relationship between working hours and work ability.

Shift work parameters and disruption of diurnal cortisol production in female hospital employees.

PubMed

Hung, Eleanor Wai Man; Aronson, Kristan J; Leung, Michael; Day, Andrew; Tranmer, Joan

2016-01-01

Shift work is associated with an increased risk of cardiovascular diseases (CVD). Disruption of cortisol production is a potential underlying mechanism. This study explored the associations of diurnal quantity and pattern of cortisol production in relation to (1) current shift work status (exclusive day versus rotating days and nights), (2) years of past shift work and (3) parameters of rotating shift work (timing, length and intensity). Female hospital employees (160 day workers and 168 rotating shift workers) from southeastern Ontario, Canada, participated in a cross-sectional study. Participants completed a baseline questionnaire and measures of body height, weight, and waist circumference were taken. Midstream urine samples were collected over two separate 24-hour periods to measure creatinine-adjusted cortisol. Total diurnal cortisol production and pattern were described with two measures of the area under the curve. The effect of shift work on cortisol was modeled using multivariable linear regression analyses. Cortisol production in day workers and shift workers on their day shift were similar; however, shift workers on the night shift had flatter diurnal cortisol curves and produced less cortisol. This suggests that night work is associated with an acute attenuation of cortisol production.

The use of synthetic ligaments in the design of an enhanced stability total knee joint replacement.

PubMed

Stokes, Michael D; Greene, Brendan C; Pietrykowski, Luke W; Gambon, Taylor M; Bales, Caroline E; DesJardins, John D

2018-03-01

Current total knee replacement designs work to address clinically desired knee stability and range of motion through a balance of retained anatomy and added implant geometry. However, simplified implant geometries such as bearing surfaces, posts, and cams are often used to replace complex ligamentous constraints that are sacrificed during most total knee replacement procedures. This article evaluates a novel total knee replacement design that incorporates synthetic ligaments to enhance the stability of the total knee replacement system. It was hypothesized that by incorporating artificial cruciate ligaments into a total knee replacement design at specific locations and lengths, the stability of the total knee replacement could be significantly altered while maintaining active ranges of motion. The ligament attachment mechanisms used in the design were evaluated using a tensile test, and determined to have a safety factor of three with respect to expected ligamentous loading in vivo. Following initial computational modeling of possible ligament orientations, a physical prototype was constructed to verify the function of the design by performing anterior/posterior drawer tests under physiologic load. Synthetic ligament configurations were found to increase total knee replacement stability up to 94% compared to the no-ligament case, while maintaining total knee replacement flexion range of motion between 0° and 120°, indicating that a total knee replacement that incorporates synthetic ligaments with calibrated location and lengths should be able to significantly enhance and control the kinematic performance of a total knee replacement system.

Final Scientific Report - Electromagnetic Interactions in Self-Assembled Metallo-Dielectric Biomaterials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dragnea, Bogdan G.

Achievements which resulted from previous DOE funding include: templated virus-like particle assembly thermodynamics, development of single particle photothermal absorption spectroscopy and dark- field spectroscopy instrumentation for the measurement of optical properties of virus-like nanoparticles, electromagnetic simulations of coupled nanoparticle cluster systems, virus contact mechanics, energy transfer and fluorescence quenching in multichromophore systems supported on biomolecular templates, and photo physical work on virus-aptamer systems. A current total of eight published research articles and a book chapter are acknowledging DOE support for the period 2013-2016.

The Error in Total Error Reduction

PubMed Central

Witnauer, James E.; Urcelay, Gonzalo P.; Miller, Ralph R.

2013-01-01

Most models of human and animal learning assume that learning is proportional to the discrepancy between a delivered outcome and the outcome predicted by all cues present during that trial (i.e., total error across a stimulus compound). This total error reduction (TER) view has been implemented in connectionist and artificial neural network models to describe the conditions under which weights between units change. Electrophysiological work has revealed that the activity of dopamine neurons is correlated with the total error signal in models of reward learning. Similar neural mechanisms presumably support fear conditioning, human contingency learning, and other types of learning. Using a computational modelling approach, we compared several TER models of associative learning to an alternative model that rejects the TER assumption in favor of local error reduction (LER), which assumes that learning about each cue is proportional to the discrepancy between the delivered outcome and the outcome predicted by that specific cue on that trial. The LER model provided a better fit to the reviewed data than the TER models. Given the superiority of the LER model with the present data sets, acceptance of TER should be tempered. PMID:23891930

Has the participation of older employees in the workforce increased? Study of the total Swedish population regarding exit from working life

PubMed Central

Nilsson, Kerstin; Östergren, Per-Olof; Kadefors, Roland; Albin, Maria

2016-01-01

Aims: This study investigated: (i) the workforce participation in Sweden among older employees before and after changes in eligibility for sickness absence and unemployment compensation by a social insurance reform; and (ii) absence and early exit mechanisms from the workforce for different professions by looking at sickness benefits, disability pension and unemployment, early statutory pension, employment pension and unregistered economic supply. Methods: A register-based follow-up study of the total Swedish workforce population of 55–64-year-olds, measured in 2004 and 2011. Results: The total proportion of individuals aged 55–64 in the workforce increased between 2004 and 2011, but the increase was mostly in professions with lower educational requirements, a lower salary and dominated by women. Both in 2004 and in 2011, men in professions with higher educational requirements more often exit working life with an early statutory pension and employment pension. In contrast, professions with lower educational requirements more often absence working life with sickness benefits, disability pension and unemployment compensation than other professions in both 2004 and 2011. Conclusions: The change in regulations seems to have contributed to an overall shrinking proportion of individuals within the sickness benefit and disability pension schemes. At the same time the proportion of individuals taking an early pension has increased. The results indicated a tendency of passing on the costs of labour-market exit within different economic compensation arrangements, as well as to the individuals themselves; for example, less sickness benefit, disability pension, but more statutory pension and employment pension earlier. PMID:26988576

Has the participation of older employees in the workforce increased? Study of the total Swedish population regarding exit from working life.

PubMed

Nilsson, Kerstin; Östergren, Per-Olof; Kadefors, Roland; Albin, Maria

2016-07-01

This study investigated: (i) the workforce participation in Sweden among older employees before and after changes in eligibility for sickness absence and unemployment compensation by a social insurance reform; and (ii) absence and early exit mechanisms from the workforce for different professions by looking at sickness benefits, disability pension and unemployment, early statutory pension, employment pension and unregistered economic supply. A register-based follow-up study of the total Swedish workforce population of 55-64-year-olds, measured in 2004 and 2011. The total proportion of individuals aged 55-64 in the workforce increased between 2004 and 2011, but the increase was mostly in professions with lower educational requirements, a lower salary and dominated by women. Both in 2004 and in 2011, men in professions with higher educational requirements more often exit working life with an early statutory pension and employment pension. In contrast, professions with lower educational requirements more often absence working life with sickness benefits, disability pension and unemployment compensation than other professions in both 2004 and 2011. CONCLUSIONS THE CHANGE IN REGULATIONS SEEMS TO HAVE CONTRIBUTED TO AN OVERALL SHRINKING PROPORTION OF INDIVIDUALS WITHIN THE SICKNESS BENEFIT AND DISABILITY PENSION SCHEMES AT THE SAME TIME THE PROPORTION OF INDIVIDUALS TAKING AN EARLY PENSION HAS INCREASED THE RESULTS INDICATED A TENDENCY OF PASSING ON THE COSTS OF LABOUR-MARKET EXIT WITHIN DIFFERENT ECONOMIC COMPENSATION ARRANGEMENTS, AS WELL AS TO THE INDIVIDUALS THEMSELVES; FOR EXAMPLE, LESS SICKNESS BENEFIT, DISABILITY PENSION, BUT MORE STATUTORY PENSION AND EMPLOYMENT PENSION EARLIER. © 2016 the Nordic Societies of Public Health.

Documentation and Control of Flow Separation on a Low Pressure Turbine Linear Cascade of Pak-B Blades Using Plasma Actuators

NASA Technical Reports Server (NTRS)

Corke, Thomas c.; Thomas, FLint, O.; Huang, Junhui

2007-01-01

This work involved the documentation and control of flow separation that occurs over low pressure turbine (LPT) blades at low Reynolds numbers. A specially constructed linear cascade was utilized to study the flow field over a generic LPT cascade consisting of Pratt & Whitney "Pak-B" shaped blades. Flow visualization, surface pressure measurements, LDV measurements, and hot-wire anemometry were conducted to examine the flow fields with and without separation control. Experimental conditions were chosen to give a range of chord Reynolds numbers (based on axial chord and inlet velocity) from 10,000 to 100,000, and a range of freestream turbulence intensities from u'/U(infinity) = 0.08 to 2.85 percent. The blade pressure distributions were measured and used to identify the region of separation that depends on Reynolds number and the turbulence intensity. Separation control was performed using dielectric barrier discharge (DBD) plasma actuators. Both steady and unsteady actuation were implemented and found to work well. The comparison between the steady and unsteady actuators showed that the unsteady actuators worked better than the steady ones. For the steady actuators, it was found that the separated region is significantly reduced. For the unsteady actuators, where the signal was pulsed, the separation was eliminated. The total pressure losses (a low Reynolds number) was reduced by approximately a factor of two. It was also found that lowest plasma duty cycle (10 percent in this work) was as effective as the highest plasma duty cycle (50 percent in this work). The mechanisms of the steady and unsteady plasma actuators were studied. It was suggested by the experimental results that the mechanism for the steady actuators is turbulence tripping, while the mechanism for the unsteady actuators is to generate a train of spanwise structures that promote mixing.

Optimal healthcare delivery to care homes in the UK: a realist evaluation of what supports effective working to improve healthcare outcomes.

PubMed

Gordon, Adam L; Goodman, Claire; Davies, Sue L; Dening, Tom; Gage, Heather; Meyer, Julienne; Schneider, Justine; Bell, Brian; Jordan, Jake; Martin, Finbarr C; Iliffe, Steve; Bowman, Clive; Gladman, John R F; Victor, Christina; Mayrhofer, Andrea; Handley, Melanie; Zubair, Maria

2018-01-05

care home residents have high healthcare needs not fully met by prevailing healthcare models. This study explored how healthcare configuration influences resource use. a realist evaluation using qualitative and quantitative data from case studies of three UK health and social care economies selected for differing patterns of healthcare delivery to care homes. Four homes per area (12 in total) were recruited. A total of 239 residents were followed for 12 months to record resource-use. Overall, 181 participants completed 116 interviews and 13 focus groups including residents, relatives, care home staff, community nurses, allied health professionals and General Practitioners. context-mechanism-outcome configurations were identified explaining what supported effective working between healthcare services and care home staff: (i) investment in care home-specific work that legitimises and values work with care homes; (ii) relational working which over time builds trust between practitioners; (iii) care which 'wraps around' care homes; and (iv) access to specialist care for older people with dementia. Resource use was similar between sites despite differing approaches to healthcare. There was greater utilisation of GP resource where this was specifically commissioned but no difference in costs between sites. activities generating opportunities and an interest in healthcare and care home staff working together are integral to optimal healthcare provision in care homes. Outcomes are likely to be better where: focus and activities legitimise ongoing contact between healthcare staff and care homes at an institutional level; link with a wider system of healthcare; and provide access to dementia-specific expertise. © The Author(s) 2018. Published by Oxford University Press on behalf of the British Geriatrics Society.

Gait in adolescent idiopathic scoliosis: energy cost analysis.

PubMed

Mahaudens, P; Detrembleur, C; Mousny, M; Banse, X

2009-08-01

Walking is a very common activity for the human body. It is so common that the musculoskeletal and cardiovascular systems are optimized to have the minimum energetic cost at 4 km/h (spontaneous speed). A previous study showed that lumbar and thoracolumbar adolescent idiopathic scoliosis (AIS) patients exhibit a reduction of shoulder, pelvic, and hip frontal mobility during gait. A longer contraction duration of the spinal and pelvic muscles was also noted. The energetic cost (C) of walking is normally linked to the actual mechanical work muscles have to perform. This total mechanical work (W(tot)) can be divided in two parts: the work needed to move the shoulders and lower limbs relative to the center of mass of the body (COM(b)) is known as the internal work (W(int)), whereas additional work, known as external work (W(ext)), is needed to accelerate and lift up the COM(b) relative to the ground. Normally, the COM(b) goes up and down by 3 cm with every step. Pathological walking usually leads to an increase in W (tot) (often because of increased vertical displacement of the COM(b)), and consequently, it increases the energetic cost. The goal of this study is to investigate the effects of scoliosis and scoliosis severity on the mechanical work and energetic cost of walking. Fifty-four female subjects aged 12 to 17 were used in this study. Thirteen healthy girls were in the control group, 12 were in scoliosis group 1 (Cobb angle [Cb] < or = 20 degrees), 13 were in scoliosis group 2 (20 degrees < Cb < 40 degrees), and 16 were in scoliosis group 3 (Cb > or = 40 degrees). They were assessed by physical examination and gait analysis. The 41 scoliotic patients had an untreated progressive left thoracolumbar or lumbar AIS. During gait analysis, the subject was asked to walk on a treadmill at 4 km h(-1). Movements of the limbs were followed by six infrared cameras, which tracked markers fixed on the body. W(int) was calculated from the kinematics. The movements of the COM(b) were derived from the ground reaction forces, and W(ext) was calculated from the force signal. W(tot) was equal to W(int) + W(ext). Oxygen consumption VO2 was measured with a mask to calculate energetic cost (C) and muscular efficiency (W(tot)/C). Statistical comparisons between the groups were performed using an analysis of variance (ANOVA). The external work (W(ext)) and internal work (W(int)) were both reduced from 7 to 22% as a function of the severity of the scoliosis curve. Overall, the total muscular mechanical work (W(tot)) was reduced from 7% to 13% in the scoliosis patients. Within scoliosis groups, the W(ext) for the group 1 (Cb > or = 20 degrees) and 2 (20 < or = Cb < or = 40 degrees) was significantly different from group 3 (Cb > or = 40 degrees). No significant differences were observed between scoliosis groups for the W(int). The W(tot) did not showed any significant difference between scoliosis groups except between group 1 and 3. The energy cost and VO2 were increased by around 30%. As a result Muscle efficiency was significantly decreased by 23% to 32%, but no significant differences related to the severity of the scoliosis were noted. This study shows that scoliosis patients have inefficient muscles during walking. Muscle efficiency was so severely decreased that it could be used as a diagnostic tool, since every scoliosis patient had an average muscle efficiency below 27%, whereas every control had an average muscle efficiency above 27%. The reduction of mechanical work found in scoliotic patients has never been observed in any pathological gait, but it is interpreted as a long term adaptation to economize energy and face poor muscle efficiency. With a relatively stiff gait, scoliosis patients also limit vertical movement of the COM(b) (smoothing the gait) and consequently, reduce W(ext) and W(int). Inefficiency of scoliosis muscles was obvious even in mild scoliosis (group 1, Cb < 20 degrees) and could be related to the prolonged muscle contraction time observed in a previous study (muscle co-contraction).

Contact mechanics of modular metal-on-polyethylene total hip replacement under adverse edge loading conditions

PubMed Central

Hua, Xijin; Li, Junyan; Wang, Ling; Jin, Zhongmin; Wilcox, Ruth; Fisher, John

2014-01-01

Edge loading can negatively impact the biomechanics and long-term performance of hip replacements. Although edge loading has been widely investigated for hard-on-hard articulations, limited work has been conducted for hard-on-soft combinations. The aim of the present study was to investigate edge loading and its effect on the contact mechanics of a modular metal-on-polyethylene (MoP) total hip replacement (THR). A three-dimensional finite element model was developed based on a modular MoP bearing. Different cup inclination angles and head lateral microseparation were modelled and their effect on the contact mechanics of the modular MoP hip replacement were examined. The results showed that lateral microseparation caused loading of the head on the rim of the cup, which produced substantial increases in the maximum von Mises stress in the polyethylene liner and the maximum contact pressure on both the articulating surface and backside surface of the liner. Plastic deformation of the liner was observed under both standard conditions and microseparation conditions, however, the maximum equivalent plastic strain in the liner under microseparation conditions of 2000 µm was predicted to be approximately six times that under standard conditions. The study has indicated that correct positioning the components to avoid edge loading is likely to be important clinically even for hard-on-soft bearings for THR. PMID:25218504

About thermometers and temperature

NASA Astrophysics Data System (ADS)

Baldovin, M.; Puglisi, A.; Sarracino, A.; Vulpiani, A.

2017-11-01

We discuss a class of mechanical models of thermometers and their minimal requirements to determine the temperature for systems out of the common scope of thermometry. In particular we consider: (1) anharmonic chains with long time of thermalization, such as the Fermi-Pasta-Ulam (FPU) model; (2) systems with long-range interactions where the equivalence of ensembles does not always hold; (3) systems featuring absolute negative temperatures. We show that for all the three classes of systems a mechanical thermometer model can be designed: a temporal average of a suitable mechanical observable of the thermometer is sufficient to get an estimate of the system’s temperature. Several interesting lessons are learnt from our numerical study: (1) the long thermalization times in FPU-like systems do not affect the thermometer, which is not coupled to normal modes but to a group of microscopic degrees of freedom; (2) a thermometer coupled to a long-range system measures its microcanonical temperature, even at values of the total energy where its canonical temperature would be very different; (3) a thermometer to read absolute negative temperatures must have a bounded total energy (as the system), otherwise it heavily perturbs the system changing the sign of its temperature. Our study shows that in order to also work in a correct way in ‘non standard’ cases, the proper model of thermometer must have a special functional form, e.g. the kinetic part cannot be quadratic.

An Adaptive Tradeoff Algorithm for Multi-issue SLA Negotiation

NASA Astrophysics Data System (ADS)

Son, Seokho; Sim, Kwang Mong

Since participants in a Cloud may be independent bodies, mechanisms are necessary for resolving different preferences in leasing Cloud services. Whereas there are currently mechanisms that support service-level agreement negotiation, there is little or no negotiation support for concurrent price and timeslot for Cloud service reservations. For the concurrent price and timeslot negotiation, a tradeoff algorithm to generate and evaluate a proposal which consists of price and timeslot proposal is necessary. The contribution of this work is thus to design an adaptive tradeoff algorithm for multi-issue negotiation mechanism. The tradeoff algorithm referred to as "adaptive burst mode" is especially designed to increase negotiation speed and total utility and to reduce computational load by adaptively generating concurrent set of proposals. The empirical results obtained from simulations carried out using a testbed suggest that due to the concurrent price and timeslot negotiation mechanism with adaptive tradeoff algorithm: 1) both agents achieve the best performance in terms of negotiation speed and utility; 2) the number of evaluations of each proposal is comparatively lower than previous scheme (burst-N).

Short mechanical biological treatment of municipal solid waste allows landfill impact reduction saving waste energy content.

PubMed

Scaglia, Barbara; Salati, Silvia; Di Gregorio, Alessandra; Carrera, Alberto; Tambone, Fulvia; Adani, Fabrizio

2013-09-01

The aim of this work was to evaluate the effects of full scale MBT process (28 d) in removing inhibition condition for successive biogas (ABP) production in landfill and in reducing total waste impact. For this purpose the organic fraction of MSW was treated in a full-scale MBT plant and successively incubated vs. untreated waste, in simulated landfills for one year. Results showed that untreated landfilled-waste gave a total ABP reduction that was null. On the contrary MBT process reduced ABP of 44%, but successive incubation for one year in landfill gave a total ABP reduction of 86%. This ABP reduction corresponded to a MBT process of 22 weeks length, according to the predictive regression developed for ABP reduction vs. MBT-time. Therefore short MBT allowed reducing landfill impact, preserving energy content (ABP) to be produced successively by bioreactor technology since pre-treatment avoided process inhibition because of partial waste biostabilization. Copyright © 2013 Elsevier Ltd. All rights reserved.

Shift work and cardiovascular disease - pathways from circadian stress to morbidity.

PubMed

Puttonen, Sampsa; Härmä, Mikko; Hublin, Christer

2010-03-01

In order to establish a causal relation between shift work and cardiovascular disease (CVD), we need to verify the pathways from the former to the latter. This paper aims to review the current knowledge of the mechanisms between shift work and CVD. Shift work can increase the risk of CVD by several interrelated psychosocial, behavioral, and physiological mechanisms. The psychosocial mechanisms relate to difficulties in controlling working hours, decreased work-life balance, and poor recovery following work. The most probable behavioral changes are weight gain and smoking. The plausible physiological and biological mechanisms are related to the activation of the autonomic nervous system, inflammation, changed lipid and glucose metabolism, and related changes in the risk for atherosclerosis, metabolic syndrome, and type II diabetes. The data provide evidence for possible disease mechanisms between shift work and CVD, but compelling evidence on any specific mechanism is missing.

Mechanical factors direct mouse aortic remodelling during early maturation

PubMed Central

Le, Victoria P.; Cheng, Jeffrey K.; Kim, Jungsil; Staiculescu, Marius C.; Ficker, Shawn W.; Sheth, Saahil C.; Bhayani, Siddharth A.; Mecham, Robert P.; Yanagisawa, Hiromi; Wagenseil, Jessica E.

2015-01-01

Numerous diseases have been linked to genetic mutations that lead to reduced amounts or disorganization of arterial elastic fibres. Previous work has shown that mice with reduced amounts of elastin (Eln+/−) are able to live a normal lifespan through cardiovascular adaptations, including changes in haemodynamic stresses, arterial geometry and arterial wall mechanics. It is not known if the timeline and presence of these adaptations are consistent in other mouse models of elastic fibre disease, such as those caused by the absence of fibulin-5 expression (Fbln5−/−). Adult Fbln5−/− mice have disorganized elastic fibres, decreased arterial compliance and high blood pressure. We examined mechanical behaviour of the aorta in Fbln5−/− mice through early maturation when the elastic fibres are being assembled. We found that the physiologic circumferential stretch, stress and modulus of Fbln5−/− aorta are maintained near wild-type levels. Constitutive modelling suggests that elastin contributions to the total stress are decreased, whereas collagen contributions are increased. Understanding how collagen fibre structure and mechanics compensate for defective elastic fibres to meet the mechanical requirements of the maturing aorta may help to better understand arterial remodelling in human elastinopathies. PMID:25652465

Mechanical properties in crumple-formed paper derived materials subjected to compression.

PubMed

Hanaor, D A H; Flores Johnson, E A; Wang, S; Quach, S; Dela-Torre, K N; Gan, Y; Shen, L

2017-06-01

The crumpling of precursor materials to form dense three dimensional geometries offers an attractive route towards the utilisation of minor-value waste materials. Crumple-forming results in a mesostructured system in which mechanical properties of the material are governed by complex cross-scale deformation mechanisms. Here we investigate the physical and mechanical properties of dense compacted structures fabricated by the confined uniaxial compression of a cellulose tissue to yield crumpled mesostructuring. A total of 25 specimens of various densities were tested under compression. Crumple formed specimens exhibited densities in the range 0.8-1.3 g cm -3 , and showed high strength to weight characteristics, achieving ultimate compressive strength values of up to 200 MPa under both quasi-static and high strain rate loading conditions and deformation energy that compares well to engineering materials of similar density. The materials fabricated in this work and their mechanical attributes demonstrate the potential of crumple-forming approaches in the fabrication of novel energy-absorbing materials from low-cost precursors such as recycled paper. Stiffness and toughness of the materials exhibit density dependence suggesting this forming technique further allows controllable impact energy dissipation rates in dynamic applications.

Contrast statistics for foveated visual systems: fixation selection by minimizing contrast entropy

NASA Astrophysics Data System (ADS)

Raj, Raghu; Geisler, Wilson S.; Frazor, Robert A.; Bovik, Alan C.

2005-10-01

The human visual system combines a wide field of view with a high-resolution fovea and uses eye, head, and body movements to direct the fovea to potentially relevant locations in the visual scene. This strategy is sensible for a visual system with limited neural resources. However, for this strategy to be effective, the visual system needs sophisticated central mechanisms that efficiently exploit the varying spatial resolution of the retina. To gain insight into some of the design requirements of these central mechanisms, we have analyzed the effects of variable spatial resolution on local contrast in 300 calibrated natural images. Specifically, for each retinal eccentricity (which produces a certain effective level of blur), and for each value of local contrast observed at that eccentricity, we measured the probability distribution of the local contrast in the unblurred image. These conditional probability distributions can be regarded as posterior probability distributions for the ``true'' unblurred contrast, given an observed contrast at a given eccentricity. We find that these conditional probability distributions are adequately described by a few simple formulas. To explore how these statistics might be exploited by central perceptual mechanisms, we consider the task of selecting successive fixation points, where the goal on each fixation is to maximize total contrast information gained about the image (i.e., minimize total contrast uncertainty). We derive an entropy minimization algorithm and find that it performs optimally at reducing total contrast uncertainty and that it also works well at reducing the mean squared error between the original image and the image reconstructed from the multiple fixations. Our results show that measurements of local contrast alone could efficiently drive the scan paths of the eye when the goal is to gain as much information about the spatial structure of a scene as possible.

20 CFR 655.122 - Contents of job offers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... employment for a total number of work hours equal to at least three-fourths of the workdays of the total... holidays. The employer must offer a total number of hours to ensure the provision of sufficient work to reach the three-fourths guarantee. The work hours must be offered during the work period specified in...

Seroepidemiological survey of health care workers in Maharashtra.

PubMed

Taishete, S; Chowdhary, A

2016-01-01

HCWs all over the world carry occupational risk of getting infected with major blood borne infections through needle stick injuries (NSIs). As health care industry has been expanding, risk of nosocomial infections is increasing proportionately. Measures to prevent it and put in place a mechanism to control these injuries are needed urgently, especially in India where there is not only increase in domestic demand but impetus in health tourism. To determine HBs Ag, HBc IgM level and to assess anti-HBs level prevalence in HCWs, in a tertiary care hospital and to study the influence of factors like age and sex in the vaccinated HCWs and formulate mechanism to increase awareness to create a safe working environment in the hospitals. 437 HCWs, working in Laboratories, Surgical, Medical or Dental departments in 11 Civil Hospitals and Sub-district Hospitals covering 8 circles of the State. Qualitative and Quantitative estimation of HBs Ag and Anti-HBs by sandwich ELISA technique and qualitative HBc IgM level by antibody-capture, non-competitive test. Liver profile (SGPT, SGOT and Alkaline Phosphatase) by IFCC method done. Tabulation and Pie Circle Result: 193 of the total 229 vaccinated HCWs tested positive for core antibody, meaning that they were infected prior to HBs Ag vaccination, leaving a total of 36 'truly' vaccinated HCWs. 11 HBs Ag positive HCWs were tested for Liver Profile and all had ALAT, ASAT and ALP within normal range. Out of total number of 141 HCWs having 10 and below IU/L anti HBs, 5 HCWs were positive for HBS Ag, showing a positivity of 3.5%. Need of vaccination and for post-vaccination serological testing of all HCWs considering the high rates of non-responders and low responders (anti-HBs-34.2%). Importance of educating the HCWs of safety precautions while handling body fluids, and the management of ' sharps ' injuries.

Earthquake Energy Dissipation in Light of High-Velocity, Slip-Pulse Shear Experiments

NASA Astrophysics Data System (ADS)

Reches, Z.; Liao, Z.; Chang, J. C.

2014-12-01

We investigated the energy dissipation during earthquakes by analysis of high-velocity shear experiments conducted on room-dry, solid samples of granite, tonalite, and dolomite sheared at slip-velocity of 0.0006-1m/s, and normal stress of 1-11.5MPa. The experimental fault were loaded in one of three modes: (1) Slip-pulse of abrupt, intense acceleration followed by moderate deceleration; (2) Impact by a spinning, heavy flywheel (225 kg); and (3) Constant velocity loading. We refer to energy dissipation in terms of power-density (PD=shear stress*slip-velocity; units of MW/m^2), and Coulomb-energy-density (CED= mechanical energy/normal stress; units of m). We present two aspects: Relative energy dissipation of the above loading modes, and relative energy dissipation between impact experiments and moderate earthquakes. For the first aspect, we used: (i) the lowest friction coefficient of the dynamic weakening; (ii) the work dissipated before reaching the lowest friction; and (iii) the cumulative mechanical work during the complete run. The results show that the slip-pulse/impact modes are energy efficient relatively to the constant-velocity mode as manifested by faster, more intense weakening and 50-90% lower energy dissipation. Thus, for a finite amount of pre-seismic crustal energy, the efficiency of slip-pulse would amplify earthquake instability. For the second aspect, we compare the experimental CED of the impact experiments to the reported breakdown energy (EG) of moderate earthquakes, Mw = 5.6 to 7.2 (Chang et al., 2012). In is commonly assumed that the seismic EG is a small fraction of the total earthquake energy, and as expected in 9 out of 11 examined earthquakes, EG was 0.005 to 0.07 of the experimental CED. We thus speculate that the experimental relation of Coulomb-energy-density to total slip distance, D, CED = 0.605 × D^0.933, is a reasonable estimate of total earthquake energy, a quantity that cannot be determined from seismic data.

The independent effects of speed and propulsive force on joint power generation in walking

PubMed Central

Browne, Michael G.; Franz, Jason R.

2017-01-01

Walking speed is modulated using propulsive forces (FP) during push-off and both preferred speed and FP decrease with aging. However, even prior to walking slower, reduced FP may be accompanied by potentially unfavorable changes in joint power generation. For example, compared to young adults, older adults exhibit a redistribution of mechanical power generation from the propulsive plantarflexor muscles to more proximal muscles acting across the knee and hip. Here, we used visual biofeedback based on real-time FP measurements to decouple and investigate the interaction between joint-level coordination, whole-body FP, and walking speed. 12 healthy young subjects walked on a dual-belt instrumented treadmill at a range of speeds (0.9 – 1.3 m/s). We immediately calculated the average FP from each speed. Subjects then walked at 1.3 m/s while completing a series of biofeedback trials with instructions to match their instantaneous FP to their averaged FP from slower speeds. Walking slower decreased FP and total positive joint work with little effect on relative joint-level contributions. Conversely, subjects walked at a constant speed with reduced FP, not by reducing total positive joint work, but by redistributing the mechanical demands of each step from the plantarflexor muscles during push-off to more proximal leg muscles during single support. Interestingly, these naturally emergent joint- and limb-level biomechanical changes, in the absence of neuromuscular constraints, resemble those due to aging. Our findings provide important reference data to understand the presumably complex interactions between joint power generation, whole-body FP, and walking speed in our aging population. PMID:28262285

Mechanical Anisotropic and Electronic Properties of Amm2-carbon under Pressure*

NASA Astrophysics Data System (ADS)

Xing, Meng-Jiang; Li, Xiao-Zhen; Yu, Shao-Jun; Wang, Fu-Yan

2017-09-01

Structural, electronic properties and mechanical anisotropy of Amm2-carbon are investigated utilizing frist-principles calculations by Cambridge Serial Total Energy Package (CASTEP) code. The work is performed with the generalized gradient approximation in the form of Perdew-Burke-Ernzerhof (PBE), PBEsol, Wu and Cohen (WC) and local density approximation in the form of Ceperley and Alder data as parameterized by Perdew and Zunger (CA-PZ). The mechanical anisotropy calculations show that Amm2-carbon exhibit large anisotropy in elastic moduli, such as Poisson’s ratio, shear modulus and Young’s modulus, and other anisotropy factors, such as the shear anisotropic factor and the universal anisotropic index AU. It is interestingly that the anisotropy in shear modulus and Young’s modulus, universal anisotropic index and the shear anisotropic factor all increases with increasing pressure, but the anisotropy in Poisson’s ratio decreases. The band structure calculations reveal that Amm2-carbon is a direct-band-gap semiconductor at ambient pressure, but with the pressure increasing, it becomes an indirect-band-gap semiconductor.

Effect of EVA on thermal stability, flammability, mechanical properties of HDPE/EVA/Mg(OH)2 composites

NASA Astrophysics Data System (ADS)

Cao, R.; Deng, Z. L.; Ma, Y. H.; Chen, X. L.

2017-06-01

In this work, ethylene vinyl acetate (EVA) is introduced to improve the properties of high-density polyethylene (HDPE)/magnesium hydroxide (MH) composites. The thermal stability, flame retardancy and mechanical properties of HDPE/EVA/MH composites are investigated and discussed. With increasing content of EVA, the limiting oxygen index (LOI) of the composites increases. The thermal stability analysis shows that the initial decomposition temperature begins at a low temperature; however, the residues of the composites at 600°C increase when HDPE is replaced by small amounts of EVA. The early degradation absorbs heat, dilute oxygen and residue. During this process, it protects the matrix inside. Compared with the HDPE/MH and EVA/MH composites, the ternary HDPE/EVA/MH composites exhibit better flame retardancy by increasing the LOI values, and reducing the heat release rate (HRR) and total heat release (THR). With increasing content of EVA, the mechanical properties can also be improved, which is attributed to the good affinity between EVA and MH particles.

Effect of chemical treatment of Kevlar fibers on mechanical interfacial properties of composites.

PubMed

Park, Soo-Jin; Seo, Min-Kang; Ma, Tae-Jun; Lee, Douk-Rae

2002-08-01

In this work, the effects of chemical treatment on Kevlar 29 fibers have been studied in a composite system. The surface characteristics of Kevlar 29 fibers were characterized by pH, acid-base value, X-ray photoelectron spectroscopy (XPS), and FT-IR. The mechanical interfacial properties of the final composites were studied by interlaminar shear strength (ILSS), critical stress intensity factor (K(IC)), and specific fracture energy (G(IC)). Also, impact properties of the composites were investigated in the context of differentiating between initiation and propagation energies and ductile index (DI) along with maximum force and total energy. As a result, it was found that chemical treatment with phosphoric acid solution significantly affected the degree of adhesion at interfaces between fibers and resin matrix, resulting in improved mechanical interfacial strength in the composites. This was probably due to the presence of chemical polar groups on Kevlar surfaces, leading to an increment of interfacial binding force between fibers and matrix in a composite system.

Interpreting activity in H(2)O-H(2)SO(4) binary nucleation.

PubMed

Bein, Keith J; Wexler, Anthony S

2007-09-28

Sulfuric acid-water nucleation is thought to be a key atmospheric mechanism for forming new condensation nuclei. In earlier literature, measurements of sulfuric acid activity were interpreted as the total (monomer plus hydrate) concentration above solution. Due to recent reinterpretations, most literature values for H(2)SO(4) activity are thought to represent the number density of monomers. Based on this reinterpretation, the current work uses the most recent models of H(2)O-H(2)SO(4) binary nucleation along with perturbation analyses to predict a decrease in critical cluster mole fraction, increase in critical cluster diameter, and orders of magnitude decrease in nucleation rate. Nucleation rate parameterizations available in the literature, however, give opposite trends. To resolve these discrepancies, nucleation rates were calculated for both interpretations of H(2)SO(4) activity and directly compared to the available parameterizations as well as the perturbation analysis. Results were in excellent agreement with older parameterizations that assumed H(2)SO(4) activity represents the total concentration and duplicated the predicted trends from the perturbation analysis, but differed by orders of magnitude from more recent parameterizations that assume H(2)SO(4) activity represents only the monomer. Comparison with experimental measurements available in the literature revealed that the calculations of the current work assuming a(a) represents the total concentration are most frequently in agreement with observations.

Antioxidant response of Phragmites australis to Cu and Cd contamination.

PubMed

Rocha, A Cristina S; Almeida, C Marisa R; Basto, M Clara P; Vasconcelos, M Teresa S D

2014-11-01

Metals are known to induce oxidative stress in plant cells. Antioxidant thiolic compounds are known to play an important role in plants׳ defence mechanisms against metal toxicity but, regarding salt marsh plants, their role is still very poorly understood. In this work, the involvement of non-protein thiols (NPT), such as cysteine (Cys), reduced glutathione (GSH), oxidised glutathione (GSSG) and total acid-soluble SH compounds (total thiols), in the tolerance mechanisms of the marsh plant Phragmites australis against Cu and Cd toxicity was assessed. Specimens of this plant, freshly harvested in an estuarine salt marsh, were exposed, for 7 days, to rhizosediment soaked with the respective elutriate contaminated with Cu (0, 10 and 100 mg/L) or Cd (0, 1, 10 mg/L). In terms of NPT production, Cu and Cd contamination induced different responses in P. australis. The content of Cys increased in plant tissue after plant exposure to Cu, whereas Cd contamination led to a decrease in GSSG levels. In general, metal contamination did not cause a significant variation on GSH levels. Both metals influenced, to some extent, the production of other thiolic compounds. Despite the accumulation of considerable amounts of Cu and Cd in belowground tissues, no visible toxicity signs were observed. So, antioxidant thiolic compounds were probably involved in the mechanisms used by P. australis to alleviate metal toxicity. As P. australis is considered suitable for phytostabilising metal-contaminated sediments, understanding its tolerance mechanisms to toxic metals is important to optimise the conditions for applying this plant in phytoremediation procedures. Copyright © 2014 Elsevier Inc. All rights reserved.

Dynamic Strain Aging Phenomena and Tensile Response of Medium-Mn TRIP Steel

NASA Astrophysics Data System (ADS)

Field, Daniel M.; Van Aken, David C.

2018-04-01

Dynamic strain aging (DSA) and rapid work hardening are typical behaviors observed in medium-Mn transformation-induced plasticity (TRIP) steel. Three alloys with manganese ranging from 10.2 to 13.8 wt pct with calculated room temperature stacking fault energies varying from - 2.1 to 0.7 mJ/m2 were investigated. Significant serrations were observed in the stress-strain behavior for two of the steels and the addition of 4.6 wt pct chromium was effective in significantly reducing the occurrence of DSA. Addition of chromium to the alloy reduced DSA by precipitation of M23(C,N)6 during batch annealing at 873 K (600 °C) for 20 hours. Three distinct DSA mechanisms were identified: one related to manganese ordering in stacking faults associated with ɛ-martensite and austenite interface, with activation energies for the onset and termination of DSA being 145 and 277 kJ/mol. A second mechanism was associated with carbon diffusion in γ-austenite where Mn-C bonding added to the total binding energy, and activation energies of 88 and 155 kJ/mol were measured for the onset and termination of DSA. A third mechanism was attributed to dislocation pinning and unpinning by nitrogen in α-ferrite with activation energies of 64 and 123 kJ/mol being identified. Tensile behaviors of the three medium manganese steels were studied in both the hot band and batch annealed after cold working conditions. Ultimate tensile strengths ranged from 1310 to 1404 MPa with total elongation of 24.1 to 34.1 pct. X-ray diffraction (XRD) was used to determine the transformation response of the steels using interrupted tensile tests at room temperature. All three of the processed steels showed evidence of two-stage TRIP where γ-austenite first transformed to ɛ-martensite, and subsequently transformed to α-martensite.

Electrically charged: An effective mechanism for soft EOS supporting massive neutron star

NASA Astrophysics Data System (ADS)

Jing, ZhenZhen; Wen, DeHua; Zhang, XiangDong

2015-10-01

The massive neutron star discoverer announced that strange particles, such as hyperons should be ruled out in the neutron star core as the soft Equation of State (EOS) can-not support a massive neutron star. However, many of the nuclear theories and laboratory experiments support that at high density the strange particles will appear and the corresponding EOS of super-dense matters will become soft. This situation promotes a challenge between the astro-observation and nuclear physics. In this work, we introduce an effective mechanism to answer this challenge, that is, if a neutron star is electrically charged, a soft EOS will be equivalently stiffened and thus can support a massive neutron star. By employing a representative soft EOS, it is found that in order to obtain an evident effect on the EOS and thus increasing the maximum stellar mass by the electrostatic field, the total net charge should be in an order of 1020 C. Moreover, by comparing the results of two kind of charge distributions, it is found that even for different distributions, a similar total charge: ~ 2.3 × 1020 C is needed to support a ~ 2.0 M ⊙ neutron star.

BAG3 regulates total MAP1LC3B protein levels through a translational but not transcriptional mechanism.

PubMed

Rodríguez, Andrea E; López-Crisosto, Camila; Peña-Oyarzún, Daniel; Salas, Daniela; Parra, Valentina; Quiroga, Clara; Morawe, Tobias; Chiong, Mario; Behl, Christian; Lavandero, Sergio

2016-01-01

Autophagy is mainly regulated by post-translational and lipid modifications of ATG proteins. In some scenarios, the induction of autophagy is accompanied by increased levels of certain ATG mRNAs such as MAP1LC3B/LC3B, ATG5 or ATG12. However, little is known about the regulation of ATG protein synthesis at the translational level. The cochaperone of the HSP70 system BAG3 (BCL2-associated athanogene 3) has been associated to LC3B lipidation through an unknown mechanism. In the present work, we studied how BAG3 controls autophagy in HeLa and HEK293 cells. Our results showed that BAG3 regulates the basal amount of total cellular LC3B protein by controlling its mRNA translation. This effect was apparently specific to LC3B because other ATG protein levels were not affected. BAG3 knockdown did not affect LC3B lipidation induced by nutrient deprivation or proteasome inhibition. We concluded that BAG3 maintains the basal amount of LC3B protein by controlling the translation of its mRNA in HeLa and HEK293 cells.

BAG3 regulates total MAP1LC3B protein levels through a translational but not transcriptional mechanism

PubMed Central

Rodríguez, Andrea E.; López-Crisosto, Camila; Peña-Oyarzún, Daniel; Salas, Daniela; Parra, Valentina; Quiroga, Clara; Morawe, Tobias; Chiong, Mario; Behl, Christian; Lavandero, Sergio

2016-01-01

ABSTRACT Autophagy is mainly regulated by post-translational and lipid modifications of ATG proteins. In some scenarios, the induction of autophagy is accompanied by increased levels of certain ATG mRNAs such as MAP1LC3B/LC3B, ATG5 or ATG12. However, little is known about the regulation of ATG protein synthesis at the translational level. The cochaperone of the HSP70 system BAG3 (BCL2-associated athanogene 3) has been associated to LC3B lipidation through an unknown mechanism. In the present work, we studied how BAG3 controls autophagy in HeLa and HEK293 cells. Our results showed that BAG3 regulates the basal amount of total cellular LC3B protein by controlling its mRNA translation. This effect was apparently specific to LC3B because other ATG protein levels were not affected. BAG3 knockdown did not affect LC3B lipidation induced by nutrient deprivation or proteasome inhibition. We concluded that BAG3 maintains the basal amount of LC3B protein by controlling the translation of its mRNA in HeLa and HEK293 cells. PMID:26654586

Dynamic mode decomposition of Fontan hemodynamics in an idealized total cavopulmonary connection

NASA Astrophysics Data System (ADS)

Delorme, Yann T.; Kerlo, Anna-Elodie M.; Anupindi, Kameswararao; Rodefeld, Mark D.; Frankel, Steven H.

2014-08-01

Univentricular heart disease is the leading cause of death from any birth defect in the first year of life. Typically, patients have to undergo three open heart surgical procedures within the first few years of their lives to eventually directly connect the superior and inferior vena cavae to the left and right pulmonary arteries forming the total cavopulmonary connection (TCPC). The end result is a weak circulation where the single working ventricle pumps oxygenated blood to the body and de-oxygenated blood flows passively through the TCPC into the lungs. The fluid dynamics of the TCPC junction involve confined impinging jets resulting in a highly unstable flow, significant mechanical energy dissipation and undesirable pressure loss. Understanding and predicting such flows is important for improving the surgical procedure and for the design of mechanical cavopulmonary assist devices. In this study, dynamic mode decomposition (DMD) is used to analyze previously obtained stereoscopic particle imaging velocimetry (SPIV) data and large eddy simulation (LES) results for an idealized TCPC. Analysis of the DMD modes from the SPIV and LES serves to both highlight the unsteady vortical dynamics and the qualitative agreement between measurements and simulations.

Radiation effects in concrete for nuclear power plants Part I: Quantification of radiation exposure and radiation effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, Kevin G; Pape, Yann Le; Remec, Igor

A large fraction of light water reactor (LWR) construction utilizes concrete, including safety-related structures such as the biological shielding and containment building. Concrete is an inherently complex material, with the properties of concrete structures changing over their lifetime due to the intrinsic nature of concrete and influences from local environment. As concrete structures within LWRs age, the total neutron fluence exposure of the components, in particular the biological shield, can increase to levels where deleterious effects are introduced as a result of neutron irradiation. This work summarizes the current state of the art on irradiated concrete, including a review ofmore » the current literature and estimates the total neutron fluence expected in biological shields in typical LWR configurations. It was found a first-order mechanism for loss of mechanical properties of irradiated concrete is due to radiation-induced swelling of aggregates, which leads to volumetric expansion of the concrete. This phenomena is estimated to occur near the end of life of biological shield components in LWRs based on calculations of estimated peak neutron fluence in the shield after 80 years of operation.« less

Comparison of the efficiency of rat papillary muscles during afterloaded isotonic contractions and contractions with sinusoidal length changes.

PubMed

Mellors, L J; Gibbs, C L; Barclay, C J

2001-05-01

The results of previous studies suggest that the maximum mechanical efficiency of rat papillary muscles is lower during a contraction protocol involving sinusoidal length changes than during one involving afterloaded isotonic contractions. The aim of this study was to compare directly the efficiency of isolated rat papillary muscle preparations in isotonic and sinusoidal contraction protocols. Experiments were performed in vitro (27 degrees C) using left ventricular papillary muscles from adult rats. Each preparation performed three contraction protocols: (i) low-frequency afterloaded isotonic contractions (10 twitches at 0.2 Hz), (ii) sinusoidal length change contractions with phasic stimulation (40 twitches at 2 Hz) and (iii) high-frequency afterloaded isotonic contractions (40 twitches at 2 Hz). The first two protocols resembled those used in previous studies and the third combined the characteristics of the first two. The parameters for each protocol were adjusted to those that gave maximum efficiency. For the afterloaded isotonic protocols, the afterload was set to 0.3 of the maximum developed force. The sinusoidal length change protocol incorporated a cycle amplitude of +/-5% resting length and a stimulus phase of -10 degrees. Measurements of force output, muscle length change and muscle temperature change were used to calculate the work and heat produced during and after each protocol. Net mechanical efficiency was defined as the proportion of the energy (enthalpy) liberated by the muscle that appeared as work. The efficiency in the low-frequency, isotonic contraction protocol was 21.1+/-1.4% (mean +/- s.e.m., N=6) and that in the sinusoidal protocol was 13.2+/-0.7%, consistent with previous results. This difference was not due to the higher frequency or greater number of twitches because efficiency in the high-frequency, isotonic protocol was 21.5+/-1.0%. Although these results apparently confirm that efficiency is protocol-dependent, additional experiments designed to measure work output unambiguously indicated that the method used to calculate work output in isotonic contractions overestimated actual work output. When net work output, which excludes work done by parallel elastic elements, rather than total work output was used to determine efficiency in afterloaded isotonic contractions, efficiency was similar to that for sinusoidal contractions. The maximum net mechanical efficiency of rat papillary muscles performing afterloaded isotonic or sinusoidal length change contractions was between 10 and 15%.

Psychosocial job conditions, fear avoidance beliefs and expected return to work following acute coronary syndrome: a cross-sectional study of fear-avoidance as a potential mediator.

PubMed

Söderberg, Mia; Rosengren, Annika; Gustavsson, Sara; Schiöler, Linus; Härenstam, Annika; Torén, Kjell

2015-12-21

Despite improvements in treatment, acute coronary syndrome remains a substantial cause for prolonged sick absences and premature retirement. Knowledge regarding what benefits return to work is limited, especially the effect of psychological processes and psychosocial work factors. The purposes of this cross-sectional study were two-fold: to examine associations between adverse psychosocial job conditions and fear-avoidance beliefs towards work, and to determine whether such beliefs mediated the relationship between work conditions and expected return to work in acute coronary syndrome survivors. Study inclusion criteria: acute myocardial infarction or unstable angina diagnosis, below 65 years of age, being a resident in the West county of Sweden and currently working. In all, 509 individuals (21.8 % women) accepted study participation and for whom all data of study interest were available for analysis. Psychosocial work variables; job demand-control and effort-reward imbalance, were assessed with standard questionnaire batteries. Linear regression models were used to investigate relationships between psychosocial factors and fear-avoidance, and to evaluate mediator effects for fear-avoidance. Both total sample and gender stratified analyses were calculated. Fear-avoidance beliefs about work were associated to psychosocial job environments characterized by high strain (β 1.4; CI 1.2-1.6), active and passive work and high effort-reward imbalance (β 0.6; CI 0.5-0.7). Further, such beliefs also mediated the relationship between adverse work conditions and expected time for return to work. However, these results were only observed in total sample analyses or among or male participants. For women only high strain was linked to fear-avoidance, and these relationships became non-significant when entering chosen confounders. This cross-sectional study showed that acute coronary syndrome survivors, who laboured under adverse psychosocial work conditions, held fear-avoidance beliefs towards their workplace. Furthermore, these beliefs mediated the relationships between - high strained or high effort-reward imbalanced work - and expected return to work. However, mentioned results were primarily found among men, which could results from few female study participants or gender differences in return to work mechanisms. Still, an earlier return to work might be promoted by interventions focusing on improved psychosocial work conditions and cognitive behavioural therapy targeting fear-avoidance beliefs.

Outgas analysis of mechanical cryocoolers for long lifetime

NASA Astrophysics Data System (ADS)

Sato, Yoichi; Shinozaki, Keisuke; Sawada, Kenichiro; Sugita, Hiroyuki; Mitsuda, Kazuhisa; Yamasaki, Noriko Y.; Nakagawa, Takao; Tsunematsu, Shoji; Otsuka, Kiyomi; Kanao, Kenichi; Yoshida, Seiji; Narasaki, Katsuhiro

2017-12-01

Mechanical cryocoolers for space applications are required to have high reliability to achieve long-term operation in orbit. ASTRO-H (Hitomi), the 6th Japanese X-ray astronomy mission, has a major scientific instrument onboard-the Soft X-ray Spectrometer (SXS) with several 20K-class two-stage Stirling (2ST) coolers and a 4K-class Joule Thomson (JT) cooler, which must operate for 3 years to ensure the lifetime of liquid helium as a cryogen for cooling of its detectors [1,2]. Other astronomical missions such as SPICA [3,4], LiteBIRD [5], and Athena [6] also have top requirements for these mechanical cryocoolers, including a 1K-class JT cooler to be operated for more than 3-5 years with no cryogen system. The reliability and lifetime of mechanical cryocoolers are generally understood to depend on (1) mechanical wear of the piston seal and valve seal, and (2) He working gas contaminated by impurity outgases, mainly H2O and CO2 released from the materials in the components of the cryocoolers. The second factor could be critical relative to causing blockage in the JT heat exchanger plumbing and the JT orifice or resulting in blockage in the Stirling regenerator and thereby degrading its performance. Thus, reducing the potential for outgassing in the cryocooler design and fabrication process, and predicting the total amount of outgases in the cryocooler are very important to ensure cryocooler lifetime and cooling performance in orbit. This paper investigates the outgas analysis of the 2ST and the 1K/4K-JT coolers for achieving a long lifetime. First, gas analysis was conducted for the materials and components of the mechanical cryocoolers, focusing on non-metallic materials as impurity gas sources. Then gas analysis of the mechanical wear effect of the piston seal materials and linear ball bearings was investigated. Finally, outgassing from a fully assembled cryocooler was measured to evaluate whether the outgas reduction process works properly to meet the requirement levels.

The Use of Micro and Nano Particulate Fillers to Modify the Mechanical and Material Properties of Acrylic Bone Cement

NASA Astrophysics Data System (ADS)

Slane, Joshua A.

Acrylic bone cement (polymethyl methacrylate) is widely used in total joint replacements to provide long-term fixation of implants. In essence, bone cement acts as a grout by filling in the voids left between the implant and the patient's bone, forming a mechanical interlock. While bone cement is considered the `gold standard' for implant fixation, issues such as mechanical failure of the cement mantle (aseptic loosening) and the development of prosthetic joint infection (PJI) still plague joint replacement procedures and often necessitate revision arthroplasty. In an effort to address these failures, various modifications are commonly made to bone cement such as mechanical reinforcement with particles/fibers and the addition of antibiotics to mitigate PJI. Despite these attempts, issues such as poor particle interfacial adhesion, inadequate drug release, and the development of multidrug resistant bacteria limit the effectiveness of bone cement modifications. Therefore, the overall goal of this work was to use micro and nanoparticles to enhance the properties of acrylic bone cement, with particular emphasis placed on improving the mechanical properties, cumulative antibiotic release, and antimicrobial properties. An acrylic bone cement (Palacos R) was modified with three types of particles in various loading ratios: mesoporous silica nanoparticles (for mechanical reinforcement), xylitol microparticles (for increased antibiotic release), and silver nanoparticles (as an antimicrobial agent). These particles were used as sole modifications, not in tandem with one another. The resulting cement composites were characterized using a variety of mechanical (macro to nano, fatigue, fracture, and dynamic), imaging, chemical, thermal, biological, and antimicrobial testing techniques. The primary outcomes of this dissertation demonstrate that: (1) mesoporous silica, as used in this work, is a poor reinforcement phase for acrylic bone cement, (2) xylitol can significantly increase the cumulative antibiotic release from acrylic cement, and (3) silver nanoparticles are a potential alternative to traditional antibiotics in cement, such as gentamicin.

An improved method for quantitatively measuring the sequences of total organic carbon and black carbon in marine sediment cores

NASA Astrophysics Data System (ADS)

Xu, Xiaoming; Zhu, Qing; Zhou, Qianzhi; Liu, Jinzhong; Yuan, Jianping; Wang, Jianghai

2018-01-01

Understanding global carbon cycle is critical to uncover the mechanisms of global warming and remediate its adverse effects on human activities. Organic carbon in marine sediments is an indispensable part of the global carbon reservoir in global carbon cycling. Evaluating such a reservoir calls for quantitative studies of marine carbon burial, which closely depend on quantifying total organic carbon and black carbon in marine sediment cores and subsequently on obtaining their high-resolution temporal sequences. However, the conventional methods for detecting the contents of total organic carbon or black carbon cannot resolve the following specific difficulties, i.e., (1) a very limited amount of each subsample versus the diverse analytical items, (2) a low and fluctuating recovery rate of total organic carbon or black carbon versus the reproducibility of carbon data, and (3) a large number of subsamples versus the rapid batch measurements. In this work, (i) adopting the customized disposable ceramic crucibles with the microporecontrolled ability, (ii) developing self-made or customized facilities for the procedures of acidification and chemothermal oxidization, and (iii) optimizing procedures and carbon-sulfur analyzer, we have built a novel Wang-Xu-Yuan method (the WXY method) for measuring the contents of total organic carbon or black carbon in marine sediment cores, which includes the procedures of pretreatment, weighing, acidification, chemothermal oxidation and quantification; and can fully meet the requirements of establishing their highresolution temporal sequences, whatever in the recovery, experimental efficiency, accuracy and reliability of the measurements, and homogeneity of samples. In particular, the usage of disposable ceramic crucibles leads to evidently simplify the experimental scenario, which further results in the very high recovery rates for total organic carbon and black carbon. This new technique may provide a significant support for revealing the mechanism of carbon burial and evaluating the capacity of marine carbon accumulation and sequestration.

In vivo degradation in modern orthopaedic UHMWPE bearings and structural characterization of a novel alternative UHMWPE material

NASA Astrophysics Data System (ADS)

Reinitz, Steven D.

Ultra-high molecular weight polyethylene (UHMWPE) remains the most common bearing material for total joint arthroplasty. Advances in radiation cross-linking and other post-consolidation treatments have led to a rapid differentiation of polyethylene products on the market, with more than twenty unique materials currently being sold by the five largest orthopaedic manufacturers alone. Through oxidation, cross-link density, and free radical measurements, this work demonstrates for the first time that in vivo material degradation is occurring in cross-linked UHMWPE materials. Based on the rate of the reaction in certain materials, it is concluded that oxidative degradation may compromise the mechanical properties of the bearings in as few as ten years, potentially leading to early clinical failure of the devices. Using the knowledge gained from this work as well as previously published observations about UHMWPE oxidation, a two-mechanism model of oxidation is proposed that offers an explanation for the observed in vivo changes. From this model it is concluded that oxidative degradation is in part the result of in vivo chemical species. The two-mechanism model of oxidation suggests that different processing techniques for UHMWPE may reduce the risk of oxidative degradation. It is concluded that by avoiding any radiation cross-linking step, Equal Channel Angular Processing (ECAP) can produce UHMWPE materials with a reduced risk for in vivo oxidation while at the same time offering superior mechanical properties compared to commercially available UHMWPE materials, as well as similar wear behavior. Using dynamic mechanical analysis, the entanglement density in ECAP materials is quantified, and is related back to the ECAP processing parameters. The relationship between entanglement density and resultant material properties is established. The results will allow informed processing parameter selection for producing optimized materials for orthopaedics and other applications.

Effects of ultrasonic energy on dyeing of polyamide (microfibre)/Lycra blends.

PubMed

Merdan, Nigar; Akalin, Mehmet; Kocak, Dilara; Usta, Ismail

2004-04-01

Although ultrasonic energy is widely used cleaning and degreasing of parts and assemblies in automotive and other industries, the use of ultrasonic energy in an industrial scale for textile washing is very new. This is due to the complexity of controlling the combination of chemical and mechanical effects, whereas with degreasing of machine parts only the mechanical effects is applied. The use of ultrasonic energy in dyeing PA/Lycra fabrics with reactive dyes has been studied spectrophotometrically in this work. PA/Lycra (85/15) blends have been dyed using conventional and ultrasonic dyeing techniques with three reactive dyes containing different chromophore and reactive groups. The dyeing carried out conventionally and by the use of ultrasonic techniques. The results were compared in terms of percentage exhaustion; total dye transferred to the washing bath after dyeing and the fastness properties.

Quenching of para-H{sub 2} with an ultracold antihydrogen atom H{sub 1s}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sultanov, Renat A.; Guster, Dennis; Adhikari, Sadhan K.

2010-02-15

In this work we report the results of calculation for quantum-mechanical rotational transitions in molecular hydrogen, H{sub 2}, induced by an ultracold ground-state antihydrogen atom H{sub 1s}. The calculations are accomplished using a nonreactive close-coupling quantum-mechanical approach. The H{sub 2} molecule is treated as a rigid rotor. The total elastic-scattering cross section {sigma}{sub el}({epsilon}) at energy {epsilon}, state-resolved rotational transition cross sections {sigma}{sub jj}{sup '}({epsilon}) between states j and j{sup '}, and corresponding thermal rate coefficients k{sub jj}{sup '}(T) are computed in the temperature range 0.004 K < or approx. T < or approx. 4 K. Satisfactory agreement with othermore » calculations (variational) has been obtained for {sigma}{sub el}({epsilon}).« less

[Functional targets of Chinese herbal medicine].

PubMed

Xiao, Bin; Wang, Yun

2010-12-01

In order to elucidate the mechanisms of Chinese herbal medicine, much work has been done based on chemical constituent-target in the molecular system. It cannot comply with the holistic efficacy of Chinese herbal medicine. Thus, the authors of this paper proposed to study the functional target adopted from Western medicine. The data of Chinese herbal function were collected from 2005 edition of The People's Republic of China Pharmacopoeia. A total of 135 functional targets were found, and a network about functional target and mode of action was built. The authors also explored the applications of functional target and the network combined with Sijunzi Decoction and Mahuang Decoction. The results, reflecting the feature of Chinese herbal medicine, will not only be helpful to elucidate the holistic mechanisms of Chinese herbal medicine, but also beneficial to studying the theory of Chinese formulas and developing new formulas.

Occupational Burnout levels in Emergency Medicine–a stage 2 nationwide study and analysis

PubMed Central

Popa, F; Arafat, R; Purcărea, VL; Popa–Velea, O; Bobirnac, G

2010-01-01

Introduction: The first stage of this nationwide study and analysis of the occupational burnout and psychological risk parameters showed a high consistency of emotional exhaustion, depersonalization and low personal accomplishment for doctors working in Emergency Departments and Emergency and Resuscitation Services. These workers were then set in the highest risk group for burnout syndrome and depression. This stageⅡ of our research will focus on those two groups analyzing causal factors, coping mechanisms and possible repercussions of these findings. Material and methods: Demographics: We have issued a total of 272 surveys from which we have received a total of 263 complete and valid ones (n=263, response rate=96, 69%). Instruments: The Maslach Burnout Inventory–Human Services Survey MBI–HSS is an instrument designed to assess the three components of the burnout syndrome: emotional exhaustion (EE), depersonalization (DP), and reduced personal accomplishment (PA). The COPE questionnaire is a 52 item addressing different ways of coping with stress. The Center for Epidemiologic Studies Depression Scale (CES-D) has been shown to be a reliable measure in assessing the number, types, and duration of depressive symptoms across racial, gender, and age categories. Results and discussion: Results were not correlated with gender, age or marital status, but an important correlation was found with professional experience in the Emergency Departments. We have shown that during the first 4 years of experience, the EE factor has been at a satisfying average of 2.4, this variable rising to an average of 2.85 after another 3 years of work. The same type of correlation was found with the CES–D results. Conclusions: Of the two surveyed groups, the EMD group showed higher values for all risk parameters and low personal accomplishment on the MBI–HSS survey. Also, emotional exhaustion and depression were found to have a powerful correlation with work experience. Coping mechanisms were found to be invariable to the general population, with a slight incline towards active coping and behavioral disengagement PMID:21254747

Development of an ash particle deposition model considering build-up and removal mechanisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kjell Strandstroem; Christian Muellera; Mikko Hupa

2007-12-15

Slagging and fouling on heat exchanger surfaces in power boilers fired with fossil fuels and fuel mixtures has a significant influence on boiler efficiency and availability. Mathematical modelling has long been considered a suitable method to assist boiler operators to determine optimized operating conditions for an existing furnace. The ultimate goal in ash deposition prediction is hereby the determination of the total amount of material deposited and hence the determination of the total reduction in efficiency. Depending on the fuels fired the total deposited mass is a combination of ash particle deposition and ash particle erosion due to non-sticky particles.more » The novel ash particle deposition model presented in this work considers deposition of sticky ash particles, cleansing of deposit by non-sticky sand particles and sticking of sand due to contact with sticky ash. The steady-state modelling results for the total amount of ash deposited on the deposition probe of an entrained flow reactor presented in this work agree well with the experimental data. Only at very high fractions of sand added as non-sticky material, a significant influence of the sand on the overall mass deposited was found. Since the model considers sticking of non-sticking sand due to contact with sticky ash, the fraction of sand deposited on the probe was especially studied. Using a correction factor to consider the influence of operating time on the steady-state simulations led to good agreement between simulations and experimental data. 12 refs., 10 figs.« less

Measuring relative work values for home care nursing services in Japan.

PubMed

Ogata, Yasuko; Kobayashi, Yasuki; Fukuda, Takashi; Mori, Katsumi; Hashimoto, Michio; Otosaka, Kayo

2004-01-01

Japan's system of Home Visit Nursing Care Stations (Station) began in 1991. To maintain the quality of services in home health nursing provided by Stations, reimbursement needs to account not only for the number of home visits, but also for the time and intensity of nursing services. This study aimed primarily to investigate the total work value and the three dimensions (time, mental effort, and physical effort) of actual visiting nursing services for the aged, and to quantify the contribution made by the three dimensions of nursing services to total work. The secondary purpose was to determine whether patient characteristics, nurse characteristics, and types of nursing services contributed to the variance in total work. Total work is defined as comprehensive work input of nursing services, with careful consideration given to both the intensity and duration of work. Self-report questionnaires about actual visiting nursing services, based on the Resource-Based Relative Value Scale, were answered by 32 nurses from three Stations in urban Yokohama, Japan. Regression analysis showed that time and intensity (physical effort and mental effort) explained 96% the variance in total work. Time alone accounted for only 39% of the variance in total work. Patient characteristics, nurse characteristics, and service type accounted for less variance in total work than did time and intensity. The study findings indicate that reimbursement of nursing services should reflect not only the time required for each visit, but also the intensity of nursing services provided, including mental effort and physical effort.

The impact of menopausal symptoms on work ability.

PubMed

Geukes, Marije; van Aalst, Mariëlle P; Nauta, Mary C E; Oosterhof, Henk

2012-03-01

Menopause is an important life event that may have a negative influence on quality of life. Work ability, a concept widely used in occupational health, can predict both future impairment and duration of sickness absence. The aim of this study was to examine the impact of menopausal symptoms on work ability. This was a cross-sectional study that used a sample of healthy working Dutch women aged 44 to 60 years. Work ability was measured using the Work Ability Index, and menopausal symptoms were measured using the Greene Climacteric Scale. Stepwise multiple linear regression models were used to examine the relationship between menopausal symptoms and work ability. A total of 208 women were included in this study. There was a significant negative correlation between total Greene Climacteric Scale score and Work Ability Index score. Total Greene Climacteric Scale score predicted 33.8% of the total variance in the Work Ability Index score. Only the psychological and somatic subscales of the Greene Climacteric Scale were significant predictors in multiple linear regression analysis. Together, they accounted for 36.5% of total variance in Work Ability Index score. Menopausal symptoms are negatively associated with work ability and may increase the risk of sickness absence.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maurer, D.

In January 1986, the Becon Construction Company - an open-shop contractor based in Houston, Texas - mobilized a work force to a construction project location at the Belridge Oil Field, near Bakersfield, California. The construction craftsmen and helpers in Becon's work force were expected to improve their level of productivity as the work proceeded because of the knowledge and skills that they would acquire as a result of the repetitive nature of the work. As it was originally organized, the Becon HOTS project represented almost a pure laboratory environment in which to collect data concerning the learning effect on workermore » productivity as well as to statistically isolate the impact on productivity of such external factors as weather, absenteeism, turnover, and especially work methods improvement techniques and pay incentives. From the outset of the HOTS project, the project manager had established an accurate system to quantitatively measure and compare the total manhours that each crew - civil, mechanical, electrical, and prefabrication -- performed at individual HOTS construction locations. Additionally, it was initially assumed that the project manager would be relatively free to implement changes to the job site conditions involving incentive pay and work methods improvement. The subsequent effect of these changes on the productivity of separate work crews could then be evaluated in terms of measured manhours per crew per HOTS.« less

Universal timescales in the rheology of spheroid cell aggregates

NASA Astrophysics Data System (ADS)

Yu, Miao; Mahtabfar, Aria; Beleen, Paul; Foty, Ramsey; Zahn, Jeffrey; Shreiber, David; Liu, Liping; Lin, Hao

2017-11-01

The rheological properties of tissue play important roles in key biological processes including embryogenesis, cancer metastasis, and wound healing. Spheroid cell aggregate is a particularly interesting model system for the study of these phenomena. In the long time, they behave like drops with a surface tension. In the short, viscoelasticity also needs to be considered. In this work, we discover two coupled and universal timescales for spheroid aggregates. A total of 12 aggregate types (total aggregate number n =290) derived from L and GBM (glioblastoma multiforme) cells are studied with microtensiometer to obtain their surface tension. They are also allowed to relax upon release of the compression forces. The two timescales are observed during the relaxation process; their values do not depend on compression time nor the degree of deformation, and are consistent among all 12 types. Following prior work (Yu et al., Phys. Rev. Lett., 115:128303; Liu et al., J. Mech. Phys. Solids, 98:309-329) we use a rigorous mathematical theory to interpret the results, which reveals intriguing properties of the aggregates on both tissue and cellular levels. The mechanics of multicellular organization reflects both complexity and regularity due to strong active regulation.

PREFACE: XXI Fluid Mechanics Conference

NASA Astrophysics Data System (ADS)

Szmyd, Janusz S.; Fornalik-Wajs, Elzbieta; Jaszczur, Marek

2014-08-01

This Conference Volume contains the papers presented at the 21st Fluid Mechanics Conference (XXI FMC) held at AGH - University of Science and Technology in Krakow, Poland, 15-18 June 2014, and accepted for Proceedings published in the Journal of Physics: Conference Series. The Fluid Mechanics Conferences have been taking place every two years since 1974, a total of forty years. The 21st Fluid Mechanics Conference (XXI FMC) is being organized under the auspices of the Polish Academy of Sciences, Committee of Mechanics. The goal of this conference is to provide a forum for the exposure and exchange of ideas, methods and results in fluid mechanics. Conference topics include, but are not limited to Aerodynamics, Atmospheric Science, Bio-Fluids, Combustion and Reacting Flows, Computational Fluid Dynamics, Experimental Fluid Mechanics, Flow Machinery, General Fluid Dynamics, Hydromechanics, Heat and Fluid Flow, Measurement Techniques, Micro- and Nano- Flow, Multi-Phase Flow, Non-Newtonian Fluids, Rotating and Stratified Flows, Turbulence. Within the general subjects of this conference, the Professor Janusz W. Elsner Competition for the best fluid mechanics paper presented during the Conference is organized. Authors holding a M.Sc. or a Ph.D. degree and who are not older than 35 years of age may enter the Competition. Authors with a Ph.D. degree must present individual papers; authors with a M.Sc. degree may present papers with their supervisor as coauthor, including original results of experimental, numerical or analytic research. Six state-of-the-art keynote papers were delivered by world leading experts. All contributed papers were peer reviewed. Recommendations were received from the International Scientific Committee, reviewers and the advisory board. Accordingly, of the 163 eligible extended abstracts submitted, after a review process by the International Scientific Committee, 137 papers were selected for presentation at the 21st Fluid Mechanics Conference, 68 papers were accepted for Proceedings published in the Journal of Physics: Conference Series. The total number of submitted and accepted papers for this year's conference represents a significant increase over previous Fluid Mechanics Conferences, and has expanded its initial national character and borders which speaks to the great vitality of fluid mechanics. We hope that these proceedings will be used not only as a document of the event but also to assess achievements and new paths to be taken in fluid mechanics research. Finally, we would like to congratulate the winners of the 2014 Professor Janusz W Elsner Competition Ruri Hidema from Japan, Fernando Tejero from Spain and Lukasz Laniewski-Wollk from Poland. Acknowledgements We would like to express grateful appreciation to our colleagues from the Polish Academy of Sciences, Committee of Mechanics, as well as to the International Scientific Committee i.e. Members and the Advisory Board. Their advice and efforts have helped us to overcome the problems normally associated with organising international meetings. Special thanks goes to the reviewers for their work in encouraging the submission of papers and the subsequent review of all papers. Their contribution cannot be overestimated. The 21st Fluid Mechanics Conference was organised by AGH University of Science and Technology, the Polish Academy of Sciences the Committee of Mechanics and the AGH-UST Foundation. Proceedings was published in the Journal of Physics: Conference Series. The demanding work involved could not have been done without the contribution of so many individuals from all institutions as well as numerous external co-workers. Without their extremely valuable help such a meeting would have been impossible. Thank you all so much! Details of the committees are available in the PDF

Unit Costs of Interlibrary Loans and Photocopies at a Regional Medical Library: Preliminary Report *

PubMed Central

Spencer, Carol C.

1970-01-01

Unit costs of providing interlibrary loans and photocopies were determined by a method not previously used for library cost studies: random time sampling with self-observation. The working time of all appropriate personnel was sampled using Random Alarm Mechanisms and a structured checklist of tasks. The total lender's unit cost per request received, including direct labor, materials, fringe benefits, and overhead, was $1.526 for originals mailed postpaid by lender, and $1.534 for photocopies mailed. Corresponding unit costs per request filled were: originals, $1.932, and photocopies, $1.763. PMID:5439910

Nonthermal Hawking radiation from NUT-Taub-like black hole

NASA Astrophysics Data System (ADS)

Zhao, GuoMing; Li, PengZhang

2012-04-01

Using Damour-Ruffini method, we investigate Hawking radiation from NUT-Taub-like (NT-like) black hole. Considering the total energy conservation and the back reaction of the particle to the spacetime, we get the radiation spectrum on the black hole event horizon, which is related to the change of Bekenstein-Hawking entropy. Meanwhile, we find that the radiation is not exactly thermal, and can take out information from the black hole, which can be used to explain the information loss paradox. The result that we get satisfies the unitary theory of quantum mechanics and is consistent with the work finished before.

Total Longitudinal Moment Calculation and Reliability Analysis of Yacht Structures

NASA Astrophysics Data System (ADS)

Zhi, Wenzheng; Lin, Shaofen

In order to check the reliability of the yacht in FRP (Fiber Reinforce Plastic) materials, in this paper, the vertical force and the calculation method of the overall longitudinal bending moment on yacht was analyzed. Specially, this paper focuses on the impact of speed on the still water bending moment on yacht. Then considering the mechanical properties of the cap type stiffeners in composite materials, the ultimate bearing capacity of the yacht has been worked out, finally the reliability of the yacht was calculated with using response surface methodology. The result can be used in yacht design and yacht driving.

Radiation research society 1952-2002. Physics as an element of radiation research.

PubMed

Inokuti, Mitio; Seltzer, Stephen M

2002-07-01

Since its inception in 1954, Radiation Research has published an estimated total of about 8700 scientific articles up to August 2001, about 520, or roughly 6%, of which are primarily related to physics. This average of about 11 articles per year indicates steadily continuing contributions by physicists, though there are appreciable fluctuations from year to year. These works of physicists concern radiation sources, dosimetry, instrumentation for measurements of radiation effects, fundamentals of radiation physics, mechanisms of radiation actions, and applications. In this review, we have selected some notable accomplishments for discussion and present an outlook for the future.

Mechanical ventilation and thoracic artificial lung assistance during mechanical circulatory support with PUCA pump: in silico study.

PubMed

De Lazzari, Claudio; Genuini, Igino; Quatember, Bernhard; Fedele, Francesco

2014-02-01

Patients assisted with left ventricular assist device (LVAD) may require prolonged mechanical ventilatory assistance secondary to postoperative respiratory failure. The goal of this work is the study of the interdependent effects LVAD like pulsatile catheter (PUCA) pump and mechanical ventilatory support or thoracic artificial lung (TAL), by the hemodynamic point of view, using a numerical simulator of the human cardiovascular system. In the simulator, different circulatory sections are described using lumped parameter models. Lumped parameter models have been designed to describe the hydrodynamic behavior of both PUCA pump and thoracic artificial lung. Ventricular behavior atrial and septum functions were reproduced using variable elastance model. Starting from simulated pathological conditions we studied the effects produced on some hemodynamic variables by simultaneous PUCA pump, thoracic artificial lung or mechanical ventilation assistance. Thoracic artificial lung was applied in parallel or in hybrid mode. The effects of mechanical ventilation have been simulated by changing mean intrathoracic pressure value from -4 mmHg to +5 mmHg. The hemodynamic variables observed during the simulations, in different assisted conditions, were: left and right ventricular end systolic (diastolic) volume, systolic/diastolic aortic pressure, mean pulmonary arterial pressure, left and right mean atrial pressure, mean systemic venous pressure and the total blood flow. Results show that the application of PUCA (without mechanical ventilatory assistance) increases the total blood flow, reduces the left ventricular end systolic volume and increases the diastolic aortic pressure. Parallel TAL assistance increases the right ventricular end diastolic (systolic) volume reduction both when PUCA is switched "ON" and both when PUCA is switched "OFF". By switching "OFF" the PUCA pump, it seems that parallel thoracic artificial lung assistance produces a greater cardiac output (respect to hybrid TAL assistance). Results concerning PUCA and TAL interaction produced by simulations cannot be compared with "in vivo" results since they are not presented in literature. But results concerning the effects produced by LVAD and mechanical ventilation have a trend consistent with those presented in literature. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Inclusive and exclusive measurements of alpha particle production mechanisms in the 7Li + 144Sm system

NASA Astrophysics Data System (ADS)

Carnelli, P. F. F.; Martinez Heimann, D.; Pacheco, A. J.; Arazi, A.; Capurro, O. A.; Fernández Niello, J. O.; Cardona, M. A.; de Barbará, E.; Figueira, J. M.; Hojman, D. L.; Martí, G. V.; Negri, A. E.

2018-01-01

In this work we have studied the production of alpha particles emitted as a consequence of different reactions in the 7Li + 144Sm system at near-barrier energies. We have obtained absolute cross sections of the total yield at backward angles and at bombarding energies of 24 and 30 MeV. We have also performed complementary exclusive measurements of non-capture breakup processes at 30 MeV. In particular, the neutron transfer followed by non-capture breakup of the 6Li ejectile, which was found to be the dominant process in the studied region, could be accounted for by estimations of a classical dynamical model. This contribution, together with estimations for the incomplete fusion and alpha particle evaporation following compound-nucleus formation, are compared to the experimental inclusive angular distributions obtained in this work.

The role of working memory capacity and interference resolution mechanisms in task switching.

PubMed

Pettigrew, Corinne; Martin, Randi C

2016-12-01

Theories of task switching have emphasized a number of control mechanisms that may support the ability to flexibly switch between tasks. The present study examined the extent to which individual differences in working memory (WM) capacity and two measures of interference resolution, response-distractor inhibition and resistance to proactive interference (PI), account for variability in task switching, including global costs, local costs, and N-2 repetition costs. A total of 102 young and 60 older adults were tested on a battery of tasks. Composite scores were created for WM capacity, response-distractor inhibition, and resistance to PI; shifting was indexed by rate residual scores, which combine response time and accuracy and account for individual differences in processing speed. Composite scores served as predictors of task switching. WM was significantly related to global switch costs. While resistance to PI and WM explained some variance in local costs, these effects did not reach significance. In contrast, none of the control measures explained variance in N-2 repetition costs. Furthermore, age effects were only evident for N-2 repetition costs, with older adults demonstrating larger costs than young adults. Results are discussed within the context of theoretical models of task switching.

Effect of Sodium Hydroxide Molarity on Physical, Mechanical and Thermal Conductivity of Metakaolin Geopolymers

NASA Astrophysics Data System (ADS)

Ain Jaya, Nur; Yun-Ming, Liew; Bakri Abdullah, Mohd Mustafa Al; Cheng-Yong, Heah; Hussin, Kamarudin

2018-03-01

In the present work, the effect of different sodium hydroxide (NaOH) molarity (6M, 8M, 10M, 12M and 14M) on the physical, mechanical and thermal conductivity of metakaolin geopolymers (MkGPs) was investigated. Geopolymers were prepared by activating the metakaolin with a mixture of NaOH with sodium silicate (Na2SiO3). The products obtained were characterized after 28 days of curing. The density, porosity, compressive strength and thermal conductivity (TC) were determined. In general, the NaOH molarity has a significant effect on the compressive strength of the MkGPs. The highest compressive strength was 14.6 MPa achieved with 10M of NaOH solution. The thermal conductivity of MkGPs measured in this work was low in the range between 0.71-0.97 W/mK. NaOH molarity had a significant effect on compressive strength but a marginal effect on thermal conductivity of MkGPs. The thermal conductivity was mainly affected by the bulk density and thus the total porosity. The results showed that the geopolymer can be considered to be used as the thermal insulating material.

Microencapsulation of Self Healing Agents for Corrosion Control Coatings

NASA Technical Reports Server (NTRS)

Jolley, S. T.; Li, W.; Buhrow, J. W.; Calle, L. M.

2011-01-01

Corrosion, the environmentally induced degradation of materials, is a very costly problem that has a major impact on the global economy. Results from a 2-year breakthrough study released in 2002 by the U.S. Federal Highway Administration (FHWA) showed that the total annual estimated direct cost associated with metallic corrosion in nearly every U.S. industry sector was a staggering $276 billion, approximately 3.1% of the nation's Gross Domestic Product (GOP). Corrosion protective coatings are widely used to protect metallic structures from the detrimental effects of corrosion but their effectiveness can be seriously compromised by mechanical damage, such as a scratch, that exposes the metallic substrate. The incorporation of a self healing mechanism into a corrosion control coating would have the potential to significantly increase its effectiveness and useful lifetime. This paper describes work performed to incorporate a number of microcapsule-based self healing systems into corrosion control coatings. The work includes the preparation and evaluation of self-healing systems based on curable epoxy, acrylate, and siloxane resins, as well as, microencapsulated systems based on passive, solvent born, healing agent delivery. The synthesis and optimization of microcapsule-based self healing systems for thin coating (less than 100 micron) will be presented.

Work-Family Conflict, Perceived Organizational Support and Professional Commitment: A Mediation Mechanism for Chinese Project Professionals

PubMed Central

2018-01-01

Projects are characterized by long working hours, complex tasks and being a kind of temporary organization. As such, work-family conflict is particularly prominent for project employees. This research examined whether and how work-family conflict affects professional commitment among Chinese project professionals. Research hypotheses were developed to explore the relationship between work-family conflict, professional commitment to the project and the mediating effects of perceived organizational support. Data were collected from 327 project managers or professionals working in construction enterprises in China; data were analyzed using structural equation modeling, applying the bootstrapping method. Results showed that there were three dimensions of work-family conflict: time-based conflict, strain-based conflict and behavior-based conflict. There were two dimensions of perceived organizational support: emotional support and instrumental support. The study also tested the negative effect of work-family conflict on professional commitment and the positive effect of perceived organizational support on professional commitment. Specifically, time-based conflict and emotional support had positive effects on professional commitment. Perceived organizational support had a total mediating effect between work-family conflict and professional commitment. The strain-based conflict dimension of work-family conflict had negative impacts on professional commitment through perceived emotional support and instrumental support. Overall, our findings extend a better understanding of work-family conflict and professional commitment in the project setting and verify the importance of social support in balancing work and family and improving employee mobility. PMID:29462860

Work-Family Conflict, Perceived Organizational Support and Professional Commitment: A Mediation Mechanism for Chinese Project Professionals.

PubMed

Zheng, Junwei; Wu, Guangdong

2018-02-15

Projects are characterized by long working hours, complex tasks and being a kind of temporary organization. As such, work-family conflict is particularly prominent for project employees. This research examined whether and how work-family conflict affects professional commitment among Chinese project professionals. Research hypotheses were developed to explore the relationship between work-family conflict, professional commitment to the project and the mediating effects of perceived organizational support. Data were collected from 327 project managers or professionals working in construction enterprises in China; data were analyzed using structural equation modeling, applying the bootstrapping method. Results showed that there were three dimensions of work-family conflict: time-based conflict, strain-based conflict and behavior-based conflict. There were two dimensions of perceived organizational support: emotional support and instrumental support. The study also tested the negative effect of work-family conflict on professional commitment and the positive effect of perceived organizational support on professional commitment. Specifically, time-based conflict and emotional support had positive effects on professional commitment. Perceived organizational support had a total mediating effect between work-family conflict and professional commitment. The strain-based conflict dimension of work-family conflict had negative impacts on professional commitment through perceived emotional support and instrumental support. Overall, our findings extend a better understanding of work-family conflict and professional commitment in the project setting and verify the importance of social support in balancing work and family and improving employee mobility.

The Working Memory and Dorsolateral Prefrontal-Hippocampal Functional Connectivity Changes in Long-Term Survival Breast Cancer Patients Treated with Tamoxifen

PubMed Central

Chen, Xingui; Tao, Longxiang; Li, Jingjing; Wu, Jiaonan; Zhu, Chunyan; Yu, Fengqiong; Zhang, Lei; Zhang, Jingjie; Qiu, Bensheng; Yu, Yongqiang; He, Xiaoxuan

2017-01-01

Abstract Background: Tamoxifen is the most widely used drug for treating patients with estrogen receptor-sensitive breast cancer. There is evidence that breast cancer patients treated with tamoxifen exhibit cognitive dysfunction. However, the underlying neural mechanism remains unclear. The present study aimed to investigate the neural mechanisms underlying working memory deficits in combination with functional connectivity changes in premenopausal women with breast cancer who received long-term tamoxifen treatment. Methods: A total of 31 premenopausal women with breast cancer who received tamoxifen and 32 matched healthy control participants were included. The participants completed n-back tasks and underwent resting-state functional magnetic resonance imaging, which measure working memory performance and brain functional connectivity, respectively. A seed-based functional connectivity analysis within the whole brain was conducted, for which the dorsolateral prefrontal cortex was chosen as the seed region. Results: Our results indicated that the tamoxifen group had significant deficits in working memory and general executive function performance and significantly lower functional connectivity of the right dorsolateral prefrontal cortex with the right hippocampus compared with the healthy controls. There were no significant changes in functional connectivity in the left dorsolateral prefrontal cortex within the whole brain between the tamoxifen group and healthy controls. Moreover, significant correlations were found in the tamoxifen group between the functional connectivity strength of the dorsolateral prefrontal cortex with the right hippocampus and decreased working memory performance. Conclusion: This study demonstrates that the prefrontal cortex and hippocampus may be affected by tamoxifen treatment, supporting an antagonistic role of tamoxifen in the long-term treatment of breast cancer patients. PMID:28177081

The error in total error reduction.

PubMed

Witnauer, James E; Urcelay, Gonzalo P; Miller, Ralph R

2014-02-01

Most models of human and animal learning assume that learning is proportional to the discrepancy between a delivered outcome and the outcome predicted by all cues present during that trial (i.e., total error across a stimulus compound). This total error reduction (TER) view has been implemented in connectionist and artificial neural network models to describe the conditions under which weights between units change. Electrophysiological work has revealed that the activity of dopamine neurons is correlated with the total error signal in models of reward learning. Similar neural mechanisms presumably support fear conditioning, human contingency learning, and other types of learning. Using a computational modeling approach, we compared several TER models of associative learning to an alternative model that rejects the TER assumption in favor of local error reduction (LER), which assumes that learning about each cue is proportional to the discrepancy between the delivered outcome and the outcome predicted by that specific cue on that trial. The LER model provided a better fit to the reviewed data than the TER models. Given the superiority of the LER model with the present data sets, acceptance of TER should be tempered. Copyright © 2013 Elsevier Inc. All rights reserved.

Male-male competition, female mate choice and their interaction: determining total sexual selection.

PubMed

Hunt, John; Breuker, Casper J; Sadowski, Jennifer A; Moore, Allen J

2009-01-01

Empirical studies of sexual selection typically focus on one of the two mechanisms of sexual selection without integrating these into a description of total sexual selection, or study total sexual selection without quantifying the contributions of all of the mechanisms of sexual selection. However, this can provide an incomplete or misleading view of how sexually selected traits evolve if the mechanisms of sexual selection are opposing or differ in form. Here, we take a two-fold approach to advocate a direction for future studies of sexual selection. We first show how a quantitative partitioning and examination of sexual selection mechanisms can inform by identifying illustrative studies that describe both male-male competition and female mate choice acting on the same trait. In our sample, the most common trait where this occurred was body size, and selection was typically linear. We found that male-male competition and female mate choice can be reinforcing or opposing, although the former is most common in the literature. The mechanisms of sexual selection can occur simultaneously or sequentially, and we found they were more likely to be opposing when the mechanisms operated sequentially. The degree and timing that these mechanisms interact have important implications for the operation of sexual selection and needs to be considered in designing studies. Our examples highlight where empirical data are needed. We especially lack standardized measures of the form and strength of selection imposed by each mechanism of sexual selection and how they combine to determine total sexual selection. Secondly, using quantitative genetic principles, we outline how the selection imposed by individual mechanisms can be measured and combined to estimate the total strength and form of sexual selection. We discuss the evolutionary consequences of combining the mechanisms of sexual selection and interpreting total sexual selection. We suggest how this approach may result in empirical progress in the field of sexual selection.

Thermal-Fatigue Crack-Growth Characteristics and Mechanical Strain Cycling Behavior of A-286 Discaloy, and 16-25-6 Austenitic Steels

NASA Technical Reports Server (NTRS)

Smith, Robert W.; Smith, Gordon T.

1960-01-01

Thermal-fatigue crack-growth characteristics of notched- and unnotched-disk specimens of A-286, Discaloy, hot-cold worked 16-25-6, and overaged 16-25-6 were experimentally studied. Separately controlled variables were total strain range (0.0043 to 0.0079 in./in.), maximum cycle temperature (1300 and 1100 F), and hold time at maximum temperature (O and 5 min). A limited number of mechanical, push-pull, constant-strain cycle tests at room temperature were made using notched and un-notched bars of the same materials. In these tests the number of cycles to failure as well as the variation of load change with accumulated cycles was measured, and the effects of mean stress were observed. Constant-strain-range mechanical-fatigue tests at room temperature revealed notched-bar fatigue life to be strongly influenced by mean stress. For a specific strain range, the longest fatigue life was always found to be associated with the least-tensile (or most compressive) mean stress. By defining thermal-fatigue life as the number of cycles required to produce a crack area of 6000 square mils, the relative thermal-fatigue resistances of the test materials were established. Notched-disk specimens of A-286 and Discaloy steels exhibited longer fatigue lives than either hot-cold worked or overaged 16-25-6. On the other hand, unnotched-disk specimens of Discaloy and hot-cold worked 16-25-6 had longer lives than A-286 and overaged 16-25-6. Separation of the crack-growth data into microstage and macrostage periods revealed that the macrostage period accounted for the greatest part of the difference among materials when tested in the notched configuration, while the microstage was largely responsible for the differences encountered in unnotched disks.

Structural stability and electronic behaviors of Co1-xOsxSi and macroscopic magnetic susceptibilities of CoSi and OsSi: GGA-PBEsol, GW-approximation and QTAIM investigations

NASA Astrophysics Data System (ADS)

Bouafia, H.; Sahli, B.; Timaoui, M. A.; Djebour, B.; Hiadsi, S.; Abidri, B.

2018-02-01

The present work represents a theoretical investigation based on FP-(L)APW + lo method of structural properties, mechanical stability and electronic properties of Co1-xOsxSi as well as the macroscopic magnetic susceptibilities of CoSi and OsSi. The structural properties such as cell parameter, bulk modulus, internal parameters and total energy of non-magnetic NM, ferromagnetic FM and antiferromagnetic AFM phases were predicted by GGA-PBEsol semilocal functional. The obtained results for CoSi and OsSi are in good agreement with those found previously. The spin, orbital and total macroscopic magnetic susceptibilities of CoSi and OsSi have been estimated and confirmed that these compounds are diamagnetic. The total energy of the ferromagnetic phase of Co1-xOsxSi (with x = 0.25, 0.5 and 0.75) is the lowest indicating that they are ferromagnetic materials. The generalized stability criteria indicate that Co1-xOsxSi maintain their mechanical stabilities under a hydrostatic pressure less than 10 GPa. The electronic properties calculated by GW-approximation indicate that CoSi and Co1-xOsxSi (with x = 0.25, 0.50 and 0.75) are semimetals whereas OsSi is a semiconductor with a pseudo-direct band-gap. The topological analysis by QTAIM and the charge density plots indicate that the strong covalent character is predominant for Cosbnd Si, Ossbnd Si and Cosbnd Os bonds.

What works in school-based energy balance behaviour interventions and what does not? A systematic review of mediating mechanisms.

PubMed

van Stralen, M M; Yildirim, M; te Velde, S J; Brug, J; van Mechelen, W; Chinapaw, M J M

2011-10-01

Obesity prevention requires effective interventions targeting the so-called energy balance-related behaviours (that is, physical activity, sedentary and dietary behaviours). To improve (cost-)effectiveness of these interventions, one needs to know the working mechanisms underlying behavioural change. Mediation analyses evaluates whether an intervention works via hypothesised working mechanisms. Identifying mediators can prompt intervention developers to strengthen effective intervention components and remove/adapt ineffective components. This systematic review aims to identify psychosocial and environmental mediators of energy balance-related behaviours interventions for youth. Studies were identified by a systematic search of electronic databases (PubMed, Embase, PsycINFO, ERIC and SPORTDiscus). Studies were included if they (1) were school-based randomised controlled or quasi-experimental studies; (2) targeted energy balance behaviours; (3) conducted among children and adolescents (4-18 years of age); (4) written in English; and (5) conducted mediation analyses. A total of 24 studies were included. We found strong evidence for self-efficacy and moderate evidence for intention as mediators of physical activity interventions. Indications were found for attitude, knowledge and habit strength to be mediators of dietary behaviour interventions. The few sedentary behaviour interventions reporting on mediating effects prevented us from forming strong conclusions regarding mediators of sedentary behaviour interventions. The majority of interventions failed to significantly change hypothesised mediators because of ineffective intervention strategies, low power and/or use of insensitive measures. Despite its importance, few studies published results of mediation analysis, and more high-quality research into relevant mediators is necessary. On the basis of the limited number of published studies, self-efficacy and intention appear to be relevant mediators for physical activity interventions. Future intervention developers are advised to provide information on the theoretical base of their intervention including the strategies applied to provide insight into which strategies are effective in changing relevant mediators. In addition, future research is advised to focus on the development, validity, reliability and sensitivity of mediator measures.

What works in school-based energy balance behaviour interventions and what does not? A systematic review of mediating mechanisms

PubMed Central

van Stralen, M M; Yildirim, M; Velde, SJ te; Brug, J; van Mechelen, W; Chinapaw, M J M

2011-01-01

Objective: Obesity prevention requires effective interventions targeting the so-called energy balance-related behaviours (that is, physical activity, sedentary and dietary behaviours). To improve (cost-)effectiveness of these interventions, one needs to know the working mechanisms underlying behavioural change. Mediation analyses evaluates whether an intervention works via hypothesised working mechanisms. Identifying mediators can prompt intervention developers to strengthen effective intervention components and remove/adapt ineffective components. This systematic review aims to identify psychosocial and environmental mediators of energy balance-related behaviours interventions for youth. Method: Studies were identified by a systematic search of electronic databases (Pubmed, Embase, PsycINFO, ERIC and SPORTDiscus). Studies were included if they (1) were school-based randomised controlled or quasi-experimental studies; (2) targeted energy balance behaviours; (3) conducted among children and adolescents (4–18 years of age); (4) written in English; and (5) conducted mediation analyses. Results: A total of 24 studies were included. We found strong evidence for self-efficacy and moderate evidence for intention as mediators of physical activity interventions. Indications were found for attitude, knowledge and habit strength to be mediators of dietary behaviour interventions. The few sedentary behaviour interventions reporting on mediating effects prevented us from forming strong conclusions regarding mediators of sedentary behaviour interventions. The majority of interventions failed to significantly change hypothesised mediators because of ineffective intervention strategies, low power and/or use of insensitive measures. Conclusion: Despite its importance, few studies published results of mediation analysis, and more high-quality research into relevant mediators is necessary. On the basis of the limited number of published studies, self-efficacy and intention appear to be relevant mediators for physical activity interventions. Future intervention developers are advised to provide information on the theoretical base of their intervention including the strategies applied to provide insight into which strategies are effective in changing relevant mediators. In addition, future research is advised to focus on the development, validity, reliability and sensitivity of mediator measures. PMID:21487398

Lower limb joint work and joint work contribution during downhill and uphill walking at different inclinations.

PubMed

Alexander, Nathalie; Strutzenberger, Gerda; Ameshofer, Lisa Maria; Schwameder, Hermann

2017-08-16

Work performance and individual joint contribution to total work are important information for creating training protocols, but were not assessed so far for sloped walking. Therefore, the purpose of this study was to analyze lower limb joint work and joint contribution of the hip, knee and ankle to total lower limb work during sloped walking in a healthy population. Eighteen male participants (27.0±4.7yrs, 1.80±0.05m, 74.5±8.2kg) walked on an instrumented ramp at inclination angles of 0°, ±6°, ±12° and ±18° at 1.1m/s. Kinematic and kinetic data were captured using a motion-capture system (Vicon) and two force plates (AMTI). Joint power curves, joint work (positive, negative, absolute) and each joint's contribution to total lower limb work were analyzed throughout the stance phase using an ANOVA with repeated measures. With increasing inclination positive joint work increased for the ankle and hip joint and in total during uphill walking. Negative joint work increased for each joint and in total work during downhill walking. Absolute work was increased during both uphill (all joints) and downhill (ankle & knee) walking. Knee joint contribution to total negative and absolute work increased during downhill walking while hip and ankle contributions decreased. This study identified, that, when switching from level to a 6° and from 6° to a 12° inclination the gain of individual joint work is more pronounced compared to switching from 12° to an 18° inclination. The results might be used for training recommendations and specific training intervention with respect to sloped walking. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanical Characterization of the Human Lumbar Intervertebral Disc Subjected to Impact Loading Conditions

NASA Astrophysics Data System (ADS)

Jamison, David, IV

Low back pain is a large and costly problem in the United States. Several working populations, such as miners, construction workers, forklift operators, and military personnel, have an increased risk and prevalence of low back pain compared to the general population. This is due to exposure to repeated, transient impact shocks, particularly while operating vehicles or other machinery. These shocks typically do not cause acute injury, but rather lead to pain and injury over time. The major focus in low back pain is often the intervertebral disc, due to its role as the major primary load-bearing component along the spinal column. The formation of a reliable standard for human lumbar disc exposure to repeated transient shock could potentially reduce injury risk for these working populations. The objective of this project, therefore, is to characterize the mechanical response of the lumbar intervertebral disc subjected to sub-traumatic impact loading conditions using both cadaveric and computational models, and to investigate the possible implications of this type of loading environment for low back pain. Axial, compressive impact loading events on Naval high speed boats were simulated in the laboratory and applied to human cadaveric specimen. Disc stiffness was higher and hysteresis was lower than quasi-static loading conditions. This indicates a shift in mechanical response when the disc is under impact loads and this behavior could be contributing to long-term back pain. Interstitial fluid loss and disc height changes were shown to affect disc impact mechanics in a creep study. Neutral zone increased, while energy dissipation and low-strain region stiffness decreased. This suggests that the disc has greater clinical instability during impact loading with progressive creep and fluid loss, indicating that time of day should be considered for working populations subjected to impact loads. A finite element model was developed and validated against cadaver specimen subjected to impacts in the laboratory. Analysis showed greater total von Mises stress and pore pressure in the components of the disc under transient shocks compared to static or quasi-static loading. These findings support the idea that impact shocks cause a change in mechanical response and are potentially damaging to the disc in the long term.

Prediction of Temperatures of Austenite Equilibrium Transformations in Steels During Thermomechanical Processing

NASA Astrophysics Data System (ADS)

Samadian, Pedram; Parsa, Mohammad Habibi; Ahmadabadi, M. Nili; Mirzadeh, Hamed

2014-10-01

Knowledge about the transformation temperatures is crucial in processing of steels especially in thermomechanical processes because microstructures and mechanical properties after processing are closely related to the extent and type of transformations. The experimental determination of critical temperatures is costly, and therefore, it is preferred to predict them by mathematical methods. In the current work, new thermodynamically based models were developed for computing the Ae3 and Acm temperatures in the equilibrium cooling conditions when austenite is deformed at elevated temperatures. The main advantage of the proposed models is their capability to predict the temperatures of austenite equilibrium transformations in steels with total alloying elements (Mn + Si + Ni + Cr + Mo + Cu) less than 5 wt.% and Si less than 1 wt.% under the deformation conditions just by using the chemical potential of constituents, without the need for determining the total Gibbs free energy of steel which requires many experiments and computations.

Theoretical modeling and experimental study of dielectric loss of the multi-push-pull mode magnetoelectric laminate composites

NASA Astrophysics Data System (ADS)

Xu, Bingbing; Ma, Jiashuai; Fang, Cong; Yao, Meng; Di, Wenning; Li, Xiaobing; Luo, Haosu

2018-02-01

In this work, we establish a dielectric loss model for multi-push-pull mode ME laminate composites. It deduces that the total dielectric loss of the ME composites equals the linear average of the dielectric loss of piezoelectric plate and epoxy resin. But further analysis of this model has indicated that we can ignore the dielectric loss of epoxy resin. To verify this model, we use three kinds of epoxy resin with different dielectric loss to fabricate multi-push-pull mode PMNT/Metglas ME laminate composites respectively. It turns out that the different kinds of epoxy resin have little influence on the total dielectric loss, capacitance and piezoelectricity of the composites, which demonstrates that our model conforms to the practical case. Therefore, we can pay more attention to the mechanical properties of epoxy resin rather than its dielectric loss on fabricating the ME laminate composites.

How Fast is Collapse of Proteins During Folding?

NASA Astrophysics Data System (ADS)

Chahine, J.; Onuchic, J. N.; Socci, N. D.

1998-03-01

Recent experiments in fast folding proteins are now starting to address the question of how fast is collapse relative to the total folding time. Using minimalist models, we are able to investigate the way in which different scenarios of folding can arise depending on the interplay between the collapse order parameter and the order parameter sensitive to specific tertiary contacts. Most of our earlier studies have focused on the limit that collapse is very fast compared to the total folding time. In this work we focus on the opposite limit, i.e., at the folding temperature, collapse and folding occurs simultaneously. The folding mechanism becomes very different in this limit. Particularly, the non-specific collapse transition, that occurs at temperatures higher than the folding temperature for the fast collapse limit, now occurs between the folding and the glass temperature. We show how this transition can be identified and its consequences for the folding kinetics.

Influence of the normalized ion flux on the constitution of alumina films deposited by plasma-assisted chemical vapor deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurapov, Denis; Reiss, Jennifer; Trinh, David H.

2007-07-15

Alumina thin films were deposited onto tempered hot working steel substrates from an AlCl{sub 3}-O{sub 2}-Ar-H{sub 2} gas mixture by plasma-assisted chemical vapor deposition. The normalized ion flux was varied during deposition through changes in precursor content while keeping the cathode voltage and the total pressure constant. As the precursor content in the total gas mixture was increased from 0.8% to 5.8%, the deposition rate increased 12-fold, while the normalized ion flux decreased by approximately 90%. The constitution, morphology, impurity incorporation, and the elastic properties of the alumina thin films were found to depend on the normalized ion flux. Thesemore » changes in structure, composition, and properties induced by normalized ion flux may be understood by considering mechanisms related to surface and bulk diffusion.« less

Enhanced magnetocaloric effect tuning efficiency in Ni-Mn-Sn alloy ribbons

NASA Astrophysics Data System (ADS)

Quintana-Nedelcos, A.; Sánchez Llamazares, J. L.; Daniel-Perez, G.

2017-11-01

The present work was undertaken to investigate the effect of microstructure on the magnetic entropy change of Ni50Mn37Sn13 ribbon alloys. Unchanged sample composition and cell parameter of austenite allowed us to study strictly the correlation between the average grain size and the total magnetic field induced entropy change (ΔST). We found that a size-dependent martensitic transformation tuning results in a wide temperature range tailoring (>40 K) of the magnetic entropy change with a reasonably small variation on the peak value of the total field induced entropy change. The peak values varied from 6.0 J kg-1 K-1 to 7.7 J kg-1 K-1 for applied fields up to 2 T. Different tuning efficiencies obtained by diverse MCE tailoring approaches are compared to highlight the advantages of the herein proposed mechanism.

Is Canadian surgical residency training stressful?

PubMed

Aminazadeh, Nasser; Farrokhyar, Forough; Naeeni, Amir; Naeeni, Marjan; Reid, Susan; Kashfi, Arash; Kahnamoui, Kamyar

2012-08-01

Surgical residency has the reputation of being arduous and stressful. We sought to determine the stress levels of surgical residents, the major causes of stress and the coping mechanisms used. We developed and distributed a survey among surgical residents across Canada. A total of 169 participants responded: 97 (57%) male and 72 (43%) female graduates of Canadian (83%) or foreign (17%) medical schools. In all, 87% reported most of the past year of residency as somewhat stressful to extremely stressful, with time pressure (90%) being the most important stressor, followed by number of working hours (83%), residency program (73%), working conditions (70%), caring for patients (63%) and financial situation (55%). Insufficient sleep and frequent call was the component of residency programs that was most commonly rated as highly stressful (31%). Common coping mechanisms included staying optimistic (86%), engaging in enjoyable activities (83%), consulting others (75%) and exercising (69%). Mental or emotional problems during residency were reported more often by women (p = 0.006), who were also more likely than men to seek help (p = 0.026), but men reported greater financial stress (p = 0.036). Foreign graduates reported greater stress related to working conditions (p < 0.001), residency program (p = 0.002), caring for family members (p = 0.006), discrimination (p < 0.001) and personal and family safety (p < 0.001) than Canadian graduates. Time pressure and working hours were the most common stressors overall, and lack of sleep and call frequency were the most stressful components of the residency program. Female sex and graduating from a non-Canadian medical school increased the likelihood of reporting stress in certain areas of residency.

Airway Complications of Total Artificial Heart.

PubMed

Pathak, Vikas; Donovan, Colin; Malhotra, Rajiv

2017-02-01

The total artificial heart is the mechanical device which is used as a bridge to the heart transplant in patients with biventricular failure. Due to the mechanical nature of the device, patients receiving total artificial heart (TAH) require to be on anticoagulation therapy. Hemorrhage and coagulopathy are few of the known complications of TAH.

Biodecoloration of Reactive Black 5 by the methylotrophic yeast Candida boidinii MM 4035.

PubMed

Martorell, María M; Pajot, Hipólito F; Ahmed, Pablo M; de Figueroa, Lucía I C

2017-03-01

Azo dyes are extensively used in textile dyeing and other industries. Effluents of dying industries are specially colored and could cause severe damage to the environment. The anaerobic treatment of textile dying effluents is nowadays the preferred option, but it could generate carcinogenic aromatic amines. Recently, yeasts have become a promising alternative, combining unicellular growth with oxidative mechanisms. This work reports the characterization of the first methylotrophic yeast with dye decolorizing ability, Candida boidinii MM 4035 and some insights into its decoloration mechanism. The analysis of two selected media revealed a possible two stages mechanism of Reactive Black 5 decoloration. In glucose poor media, decoloration is incomplete and only the first stage proceeds, leading to the accumulation of a purple compound. In media with higher glucose concentrations, the yeast is able to decolorize totally an initial concentration of 200mg/L. The entire process is co-metabolic, being largely dependent on glucose concentration but being able to proceed with several nitrogen sources. Manganese dependent peroxidase but not laccase activity could be detected during decoloration. Aromatic amines do not accumulate in culture media, supporting an oxidative decoloration mechanism of unknown ecophysiological relevance. Copyright © 2016. Published by Elsevier B.V.

Preparation, characterization and dynamical mechanical properties of dextran-coated iron oxide nanoparticles (DIONPs).

PubMed

Can, Hatice Kaplan; Kavlak, Serap; ParviziKhosroshahi, Shahed; Güner, Ali

2018-03-01

Dextran-coated iron oxide nanoparticles (DIONPs) with appropriate surface chemistry exhibit many interesting properties that can be exploited in a variety of biomedical applications such as magnetic resonance imaging (MRI) contrast enhancement, tissue repair, hyperthermia, drug delivery and in cell separation. This paper reports the experimental detail for preparation, characterization and investigation of thermal and dynamical mechanical characteristics of the dextran-coated Fe 3 O 4 magnetic nanoparticles. In our work, DIONPs were prepared in a 1:2 ratio of Fe(II) and Fe(III) salt in the HCl solution with NaOH at given temperature. The obtained dextran-coated iron-oxide nanoparticles structure-property correlation was characterized by spectroscopic methods; attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and XRD. Coating dextran on the iron-oxide proof of important peaks can be seen from the ATR-FTIR. Dramatic crystallinity increment can be observed from the XRD pattern of the iron-oxide dextran nanoparticles. The thermal analysis was examined by differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA) and differential thermal analysis (DTA). Dynamical mechanical properties of dextran nanoparticles were analysed by dynamic mechanical analysis (DMA). Thermal stability of the iron oxide dextran nanoparticles is higher than that of the dextran.

Hydrolytically degradable poly(ethylene glycol) hydrogel scaffolds with tunable degradation and mechanical properties

PubMed Central

Zustiak, Silviya P.

2011-01-01

The objective of this work was to create three-dimensional (3D) hydrogel matrices with defined mechanical properties, as well as tunable degradability for use in applications involving protein delivery and cell encapsulation. Thus, we report the synthesis and characterization of a novel hydrolytically degradable poly(ethylene glycol) (PEG) hydrogel composed of PEG vinyl sulfone (PEG-VS) cross-linked with PEG-diester-dithiol. Unlike previously reported degradable PEG-based hydrogels, these materials are homogeneous in structure, fully hydrophilic and have highly specific cross-linking chemistry. We characterized hydrogel degradation and associated trends in mechanical properties, i.e., storage modulus (G′), swelling ratio (QM), and mesh size (ξ). Degradation time and the monitored mechanical properties of the hydrogel correlated with cross-linker molecular weight, cross-linker functionality, and total polymer density; these properties changed predictably as degradation proceeded (G′ decreased, whereas QM and ξ increased) until the gels reached complete degradation. Balb/3T3 fibroblast adhesion and proliferation within the 3D hydrogel matrices were also verified. In sum, these unique properties indicate that the reported degradable PEG hydrogels are well poised for specific applications in protein and cell delivery to repair soft tissue. PMID:20355705

Man-equivalent telepresence through four fingered human-like hand system

NASA Technical Reports Server (NTRS)

Jau, Bruno M.

1992-01-01

The author describes a newly developed mechanical hand system. The robot hand is in human-like configuration with a thumb and three fingers, a palm, a wrist, and the forearm in which the hand and wrist actuators are located. Each finger and the wrist has its own active electromechanical compliance system, allowing the joint drive trains to be stiffened or loosened. This mechanism imitates the human muscle dual function of positioner and stiffness controller. This is essential for soft grappling operations. The hand-wrist assembly has 16 finger joints, three wrist joints, and five compliance mechanisms for a total of 24 degrees of freedom. The strength of the hand is roughly half that of the human hand and its size is comparable to a male hand. The hand is controlled through an exoskeleton glove controller that the operator wears. The glove provides the man-machine interface in telemanipulation control mode: it senses the operator's inputs to guide the mechanical hand in hybrid position and force control. The hand system is intended for dexterous manipulations in structured environments. Typical applications will include work in hostile environment such as space operations and nuclear power plants.

Experimental estimation of migration and transfer of organic substances from consumer articles to cotton wipes: Evaluation of underlying mechanisms.

PubMed

Clausen, Per Axel; Spaan, Suzanne; Brouwer, Derk H; Marquart, Hans; le Feber, Maaike; Engel, Roel; Geerts, Lieve; Jensen, Keld Alstrup; Kofoed-Sørensen, Vivi; Hansen, Brian; De Brouwere, Katleen

2016-01-01

The aim of this work was to identify the key mechanisms governing transport of organic chemical substances from consumer articles to cotton wipes. The results were used to establish a mechanistic model to improve assessment of dermal contact exposure. Four types of PVC flooring, 10 types of textiles and one type of inkjet printed paper were used to establish the mechanisms and model. Kinetic extraction studies in methanol demonstrated existence of matrix diffusion and indicated the presence of a substance surface layer on some articles. Consequently, the proposed substance transfer model considers mechanical transport from a surface film and matrix diffusion in an article with a known initial total substance concentration. The estimated chemical substance transfer values to cotton wipes were comparable to the literature data (relative transfer ∼ 2%), whereas relative transfer efficiencies from spiked substrates were high (∼ 50%). For consumer articles, high correlation (r(2)=0.92) was observed between predicted and measured transfer efficiencies, but concentrations were overpredicted by a factor of 10. Adjusting the relative transfer from about 50% used in the model to about 2.5% removed overprediction. Further studies are required to confirm the model for generic use.

Dental glass ionomer cement reinforced by cellulose microfibers and cellulose nanocrystals.

PubMed

Silva, Rafael M; Pereira, Fabiano V; Mota, Felipe A P; Watanabe, Evandro; Soares, Suelleng M C S; Santos, Maria Helena

2016-01-01

The aim of this work was to evaluate if the addition of cellulose microfibers (CmF) or cellulose nanocrystals (CNC) would improve the mechanical properties of a commercial dental glass ionomer cement (GIC). Different amounts of CmF and CNC were previously prepared and then added to reinforce the GIC matrix while it was being manipulated. Test specimens with various concentrations of CmF or CNC in their total masses were fabricated and submitted to mechanical tests (to evaluate their compressive and diametral tensile strength,modulus, surface microhardness and wear resistance) and characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FTIR). The incorporation of CmF in the GIC matrix did not greatly improve the mechanical properties of GIC. However, the addition of a small amount of CNC in the GIC led to significant improvements in all of the mechanical properties evaluated: compressive strength (increased up to 110% compared with the control group), elastic modulus increased by 161%, diametral tensile strength increased by 53%, and the mass loss decreased from 10.95 to 3.87%. Because the composites presented a considerable increase in mechanical properties, the modification of the conventional GIC with CNC can represent a new and promising dental restorative material.

Integrating new practices: a qualitative study of how hospital innovations become routine.

PubMed

Brewster, Amanda L; Curry, Leslie A; Cherlin, Emily J; Talbert-Slagle, Kristina; Horwitz, Leora I; Bradley, Elizabeth H

2015-12-05

Hospital quality improvement efforts absorb substantial time and resources, but many innovations fail to integrate into organizational routines, undermining the potential to sustain the new practices. Despite a well-developed literature on the initial implementation of new practices, we have limited knowledge about the mechanisms by which integration occurs. We conducted a qualitative study using a purposive sample of hospitals that participated in the State Action on Avoidable Rehospitalizations (STAAR) initiative, a collaborative to reduce hospital readmissions that encouraged members to adopt new practices. We selected hospitals where risk-standardized readmission rates (RSRR) had improved (n = 7) or deteriorated (n = 3) over the course of the first 2 years of the STAAR initiative (2010-2011 to 2011-2012) and interviewed a range of staff at each site (90 total). We recruited hospitals until reaching theoretical saturation. The constant comparative method was used to conduct coding and identification of key themes. When innovations were successfully integrated, participants consistently reported that a small number of key staff held the innovation in place for as long as a year while more permanent integrating mechanisms began to work. Depending on characteristics of the innovation, one of three categories of integrating mechanisms eventually took over the role of holding new practices in place. Innovations that proved intrinsically rewarding to the staff, by making their jobs easier or more gratifying, became integrated through shifts in attitudes and norms over time. Innovations for which the staff did not perceive benefits to themselves were integrated through revised performance standards if the innovation involved complex tasks and through automation if the innovation involved simple tasks. Hospitals have an opportunity to promote the integration of new practices by planning for the extended effort required to hold a new practice in place while integration mechanisms take hold. By understanding how integrating mechanisms correspond to innovation characteristics, hospitals may be able to foster integrating mechanisms most likely to work for particular innovations.

The independent effects of speed and propulsive force on joint power generation in walking.

PubMed

Browne, Michael G; Franz, Jason R

2017-04-11

Walking speed is modulated using propulsive forces (F P ) during push-off and both preferred speed and F P decrease with aging. However, even prior to walking slower, reduced F P may be accompanied by potentially unfavorable changes in joint power generation. For example, compared to young adults, older adults exhibit a redistribution of mechanical power generation from the propulsive plantarflexor muscles to more proximal muscles acting across the knee and hip. Here, we used visual biofeedback based on real-time F P measurements to decouple and investigate the interaction between joint-level coordination, whole-body F P , and walking speed. 12 healthy young subjects walked on a dual-belt instrumented treadmill at a range of speeds (0.9-1.3m/s). We immediately calculated the average F P from each speed. Subjects then walked at 1.3m/s while completing a series of biofeedback trials with instructions to match their instantaneous F P to their averaged F P from slower speeds. Walking slower decreased F P and total positive joint work with little effect on relative joint-level contributions. Conversely, subjects walked at a constant speed with reduced F P , not by reducing total positive joint work, but by redistributing the mechanical demands of each step from the plantarflexor muscles during push-off to more proximal leg muscles during single support. Interestingly, these naturally emergent joint- and limb-level biomechanical changes, in the absence of neuromuscular constraints, resemble those due to aging. Our findings provide important reference data to understand the presumably complex interactions between joint power generation, whole-body F P , and walking speed in our aging population. Copyright © 2017 Elsevier Ltd. All rights reserved.

Red blood cells in sports: effects of exercise and training on oxygen supply by red blood cells

PubMed Central

Mairbäurl, Heimo

2013-01-01

During exercise the cardiovascular system has to warrant substrate supply to working muscle. The main function of red blood cells in exercise is the transport of O2 from the lungs to the tissues and the delivery of metabolically produced CO2 to the lungs for expiration. Hemoglobin also contributes to the blood's buffering capacity, and ATP and NO release from red blood cells contributes to vasodilation and improved blood flow to working muscle. These functions require adequate amounts of red blood cells in circulation. Trained athletes, particularly in endurance sports, have a decreased hematocrit, which is sometimes called “sports anemia.” This is not anemia in a clinical sense, because athletes have in fact an increased total mass of red blood cells and hemoglobin in circulation relative to sedentary individuals. The slight decrease in hematocrit by training is brought about by an increased plasma volume (PV). The mechanisms that increase total red blood cell mass by training are not understood fully. Despite stimulated erythropoiesis, exercise can decrease the red blood cell mass by intravascular hemolysis mainly of senescent red blood cells, which is caused by mechanical rupture when red blood cells pass through capillaries in contracting muscles, and by compression of red cells e.g., in foot soles during running or in hand palms in weightlifters. Together, these adjustments cause a decrease in the average age of the population of circulating red blood cells in trained athletes. These younger red cells are characterized by improved oxygen release and deformability, both of which also improve tissue oxygen supply during exercise. PMID:24273518

Impact of Different Binders on the Roughness, Adhesion Strength, and Other Properties of Mortars with Expanded Cork.

PubMed

Barnat-Hunek, Danuta; Widomski, Marcin K; Szafraniec, Małgorzata; Łagód, Grzegorz

2018-03-01

The aim of the research that is presented in this paper was to evaluate the physical and mechanical properties of heat-insulating mortars with expanded cork aggregates and different binders. In this work, the measurements of surface roughness and adhesion strength, supported by determination of basic mechanical and physical parameters, such as density, bulk density, open porosity, total porosity, absorbability, thermal conductivity coefficient, compressive strength, flexural strength, and frost resistance of mortars containing expanded oak cork, were performed. The scanning electron microscope (SEM) investigations demonstrated the microstructure, contact zone, and distribution of pores in the heat-insulating mortars containing expanded cork. The results indicated that the addition of expanded cork and different binders in heat-insulating mortars triggers changes in their roughness and adhesion strength. The SEM research confirmed the very good adhesion of the paste to the cork aggregate.

Impact of Different Binders on the Roughness, Adhesion Strength, and Other Properties of Mortars with Expanded Cork

PubMed Central

Barnat-Hunek, Danuta; Widomski, Marcin K.; Szafraniec, Małgorzata; Łagód, Grzegorz

2018-01-01

The aim of the research that is presented in this paper was to evaluate the physical and mechanical properties of heat-insulating mortars with expanded cork aggregates and different binders. In this work, the measurements of surface roughness and adhesion strength, supported by determination of basic mechanical and physical parameters, such as density, bulk density, open porosity, total porosity, absorbability, thermal conductivity coefficient, compressive strength, flexural strength, and frost resistance of mortars containing expanded oak cork, were performed. The scanning electron microscope (SEM) investigations demonstrated the microstructure, contact zone, and distribution of pores in the heat-insulating mortars containing expanded cork. The results indicated that the addition of expanded cork and different binders in heat-insulating mortars triggers changes in their roughness and adhesion strength. The SEM research confirmed the very good adhesion of the paste to the cork aggregate. PMID:29494525

Influence of beta-radiation sterilisation in properties of new chitosan/soybean protein isolate membranes for guided bone regeneration.

PubMed

Silva, R M; Elvira, C; Mano, J F; San Román, J; Reis, R L

2004-04-01

Novel chitosan (cts) and soybean protein isolate (SI) blended membranes were prepared. These membranes were produced by solvent casting. Besides combining the advantages of both materials, cts/SI membranes exhibit a biphasic structure that will eventually originate in situ porous formation, through a two-step degradation mechanism. In this particular work the effect of beta-radiation over the properties of these membranes was evaluated. beta-radiation sterilisation was performed at three different doses (25, 50 and 100 kGy) and eventual surface chemical changes were evaluated by Fourier transformed infrared--with attenuated total reflection and contact angle measurements. Moreover, eventual bulk properties changes due to beta-radiation were assessed by means of mechanical tensile tests and water uptake measurements. In general, no substantial changes were detected on the studied properties, with the exception of the surface energy that was found to be slightly increased for higher applied doses.

Cognitive mechanisms underlying third graders' arithmetic skills: Expanding the pathways to mathematics model.

PubMed

Träff, Ulf; Olsson, Linda; Skagerlund, Kenny; Östergren, Rickard

2018-03-01

A modified pathways to mathematics model was used to examine the cognitive mechanisms underlying arithmetic skills in third graders. A total of 269 children were assessed on tasks tapping the four pathways and arithmetic skills. A path analysis showed that symbolic number processing was directly supported by the linguistic and approximate quantitative pathways. The direct contribution from the four pathways to arithmetic proficiency varied; the linguistic pathway supported single-digit arithmetic and word problem solving, whereas the approximate quantitative pathway supported only multi-digit calculation. The spatial processing and verbal working memory pathways supported only arithmetic word problem solving. The notion of hierarchical levels of arithmetic was supported by the results, and the different levels were supported by different constellations of pathways. However, the strongest support to the hierarchical levels of arithmetic were provided by the proximal arithmetic skills. Copyright © 2017 Elsevier Inc. All rights reserved.

Hot rolling and annealing effects on the microstructure and mechanical properties of ODS austenitic steel fabricated by electron beam selective melting

NASA Astrophysics Data System (ADS)

Gao, Rui; Ge, Wen-jun; Miao, Shu; Zhang, Tao; Wang, Xian-ping; Fang, Qian-feng

2016-03-01

The grain morphology, nano-oxide particles and mechanical properties of oxide dispersion strengthened (ODS)-316L austenitic steel synthesized by electron beam selective melting (EBSM) technique with different post-working processes, were explored in this study. The ODS-316L austenitic steel with superfine nano-sized oxide particles of 30-40 nm exhibits good tensile strength (412 MPa) and large total elongation (about 51%) due to the pinning effect of uniform distributed oxide particles on dislocations. After hot rolling, the specimen exhibits a higher tensile strength of 482 MPa, but the elongation decreases to 31.8% owing to the introduction of high-density dislocations. The subsequent heat treatment eliminates the grain defects induced by hot rolling and increases the randomly orientated grains, which further improves the strength and ductility of EBSM ODS-316L steel.

Molecular spectroscopic study for suggested mechanism of chrome tanned leather

NASA Astrophysics Data System (ADS)

Nashy, Elshahat H. A.; Osman, Osama; Mahmoud, Abdel Aziz; Ibrahim, Medhat

2012-03-01

Collagen represents the structural protein of the extracellular matrix, which gives strength of hides and/or skin under tanning process. Chrome tan is the most important tanning agent all over the world. The methods for production of leather evolved over several centuries as art and engineering with little understanding of the underlying science. The present work is devoted to suggest the most probable mechanistic action of chrome tan on hide proteins. First the affect of Cr upon hide protein is indicated by the studied mechanical properties. Then the spectroscopic characterization of the hide protein as well as chrome tanned leather was carried out with Horizontal Attenuated Total Reflection (HATR) FT-IR. The obtained results indicate how the chromium can attached with the active sites of collagen. Molecular modeling confirms that chromium can react with amino as well as carboxylate groups. Four schemes were obtained to describe the possible interactions of chrome tan with hide proteins.

Analysis of intelligent hinged shell structures: deployable deformation and shape memory effect

NASA Astrophysics Data System (ADS)

Shi, Guang-Hui; Yang, Qing-Sheng; He, X. Q.

2013-12-01

Shape memory polymers (SMPs) are a class of intelligent materials with the ability to recover their initial shape from a temporarily fixable state when subjected to external stimuli. In this work, the thermo-mechanical behavior of a deployable SMP-based hinged structure is modeled by the finite element method using a 3D constitutive model with shape memory effect. The influences of hinge structure parameters on the nonlinear loading process are investigated. The total shape memory of the processes the hinged structure goes through, including loading at high temperature, decreasing temperature with load carrying, unloading at low temperature and recovering the initial shape with increasing temperature, are illustrated. Numerical results show that the present constitutive theory and the finite element method can effectively predict the complicated thermo-mechanical deformation behavior and shape memory effect of SMP-based hinged shell structures.

Nursing work hours: individual needs versus working conditions.

PubMed

Silva, Amanda Aparecida; Rotenberg, Lúcia; Fischer, Frida Marina

2011-12-01

To assess factors associated with professional and total hours of work (work + home) among nursing staff. Cross-sectional study conducted in a university hospital in the city of São Paulo, southeastern Brazil, between 2004 and 2005. A total of 696 workers (nurses, nurse technicians and aids), mostly women (87.8%) working day and/or night shifts, participated in the study. A self-administered questionnaire was used to collected information on demographic characteristics, and working and life conditions. Translated and adapted into Portuguese versions of the Job Stress Scale, Effort-reward imbalance, Short-Form-Health-related quality of life and the Work Ability Index were also administered. Logistic regression models were used for data analysis. Sole breadwinner, working night shifts and effort-reward imbalance were the variables associated with both professional (OR = 3.38, OR = 10.43, OR = 2.07, respectively) and total hours of work (OR = 1.57, OR = 3.37, OR = 2.75, respectively). There was no significant association between the variables related to hours of work and low Work Ability Index. Inadequate rest at home was statistically associated with professional (OR = 2.47) and total hours of work (OR = 1.48). Inadequate leisure time was significantly associated with professional hours of work (OR = 1.58) and barely associated with total hours of work (OR = 1.43). The sole breadwinner, working night shifts and effort-reward imbalance are variables that need to be further investigated in studies on work hours among nursing staff. These studies should explore workers' income and the relationship between effort and reward, taking into consideration gender issues.

Considerations about projectile and target X-rays induced during heavy ion bombardment

NASA Astrophysics Data System (ADS)

Fernandes, F.; Bauer, D. V.; Duarte, A.; Ferrari, T. M.; Niekraszewicz, L. A. B.; Amaral, L.; Dias, J. F.

2018-02-01

In this work we present some results concerning the X-rays emitted by heavy ions during target bombardment. In this case, Cl4+ and Cl5+ ions with energies from 4 MeV to 10 MeV were employed to irradiate vitreous carbon planchets. Moreover, total X-ray production cross sections of titanium X-rays induced by chlorine ions were obtained as well for the same energy range. Only inner shell transitions were considered in the present work. The titanium target consisted of a thin film deposited over vitreous carbon planchets. The results indicate that the projectile X-ray yields increase as a function of the bombarding energy for the present energy range. Effects due to projectile charge state appears to be of minor importance at these low ion velocities. It is shown that a simple exponential function can represent the continuum background of such complex spectra. The chlorine transition rates Kβ/Kα obtained from chlorine acting as a projectile interacting with a carbon target are about half the value when compared to the chlorine Kβ/Kα ratios obtained when a LiCl target is bombarded with C+ and C3+ ions with energies from 2 MeV to 6 MeV. As far as the total X-ray production cross sections of Ti induced by chlorine ions are concerned, the ECPSSR theory underestimates the Ti total X-rays production cross sections by several orders of magnitude. The role of electron capture and possible mechanisms responsible for these effects are discussed.

Ab initio study of charge transfer in B2+ low-energy collisions with atomic hydrogen

NASA Astrophysics Data System (ADS)

Turner, A. R.; Cooper, D. L.; Wang, J. G.; Stancil, P. C.

2003-07-01

Charge transfer processes due to collisions of ground state B2+(2s 2S) ions with atomic hydrogen are investigated using the quantum-mechanical molecular-orbital close-coupling (MOCC) method. The MOCC calculations utilize ab initio adiabatic potentials and nonadiabatic radial and rotational coupling matrix elements obtained with the spin-coupled valence-bond approach. Total and state-selective cross sections and rate coefficients are presented. Comparison with the existing experiments shows our results to be in good agreement. When E<80 eV/u, the differences between the current total MOCC cross sections with and without rotational coupling are small (<3%). Rotational coupling becomes more important with increasing energy: for collision energies E>400 eV/u, inclusion of rotational coupling increases the total cross section by 50% 80%, improving the agreement between the current calculations and experiments. For state-selective cross sections, rotational coupling induces mixing between different symmetries; however, its effect, especially at low collision energies, is not as important as had been suggested in previous work.

Solar updraft power generator with radial and curved vanes

NASA Astrophysics Data System (ADS)

Hafizh, Hadyan; Hamsan, Raziff; Zamri, Aidil Azlan Ahmad; Keprawi, Mohamad Fairuz Mohamad; Shirato, Hiromichi

2018-02-01

Solar radiation is the largest source of energy available on earth and the solar updraft power generator (SUPG) is a renewable energy facility capable of harnessing its abundant power. Unlike the conventional wind turbines that harness natural wind in the atmosphere and often encounter with the intermittent issue or even complete cut-off from airflow, the SUPG creates artificial wind as a result of solar-induced convective flows. However, the SUPG has an inherent low total efficiency due to the conversion of thermal energy into pressure energy. Acknowledging the low efficiency and considering its potential as a renewable energy facility, the current work aims to increase the total efficiency by installing a series of guide walls inside the collector. Two types of guide walls were used i.e. radial and curved vanes. The result with curved vanes showed that the updraft velocity is higher compare to those without vanes. About 18% and 64% improvement of updraft velocity and mechanical power were attained respectively. Furthermore, it was observed that the role of radial vanes configuration was more to produce a smooth updraft velocity profile rather than increasing the total efficiency.

The use of the articulated total body model as a robot dynamics simulation tool

NASA Technical Reports Server (NTRS)

Obergfell, Louise A.; Avula, Xavier J. R.; Kalegs, Ints

1988-01-01

The Articulated Total Body (ATB) model is a computer sumulation program which was originally developed for the study of aircrew member dynamics during ejection from high-speed aircraft. This model is totally three-dimensional and is based on the rigid body dynamics of coupled systems which use Euler's equations of motion with constraint relations of the type employed in the Lagrange method. In this paper the use of the ATB model as a robot dynamics simulation tool is discussed and various simulations are demonstrated. For this purpose the ATB model has been modified to allow for the application of torques at the joints as functions of state variables of the system. Specifically, the motion of a robotic arm with six revolute articulations with joint torques prescribed as functions of angular displacement and angular velocity are demonstrated. The simulation procedures developed in this work may serve as valuable tools for analyzing robotic mechanisms, dynamic effects, joint load transmissions, feed-back control algorithms employed in the actuator control and end-effector trajectories.

Quantifying the influence of twin boundaries on the deformation of nanocrystalline copper using atomistic simulations

DOE PAGES

Tucker, Garritt J.; Foiles, Stephen Martin

2014-09-22

Over the past decade, numerous efforts have sought to understand the influence of twin boundaries on the behavior of polycrystalline materials. Early results suggested that twin boundaries within nanocrystalline face-centered cubic metals have a considerable effect on material behavior by altering the activated deformation mechanisms. In this work, we employ molecular dynamics simulations to elucidate the role of twin boundaries on the deformation of <100> columnar nanocrystalline copper at room temperature under uniaxial strain. We leverage non-local kinematic metrics, formulated from continuum mechanics theory, to compute atomically-resolved rotational and strain fields during plastic deformation. These results are then utilized tomore » compute the distribution of various nanoscale mechanisms during straining, and quantitatively resolve their contribution to the total strain accommodation within the microstructure, highlighting the fundamental role of twin boundaries. Our results show that nanoscale twins influence nanocrystalline copper by altering the cooperation of fundamental deformation mechanisms and their contributed role in strain accommodation, and we present new methods for extracting useful information from atomistic simulations. The simulation results suggest a tension–compression asymmetry in the distribution of deformation mechanisms and strain accommodation by either dislocations or twin boundary mechanisms. In highly twinned microstructures, twin boundary migration can become a significant deformation mode, in comparison to lattice dislocation plasticity in non-twinned columnar microstructures, especially during compression.« less

Characterization of the anisotropic mechanical behavior of human abdominal wall connective tissues.

PubMed

Astruc, Laure; De Meulaere, Maurice; Witz, Jean-François; Nováček, Vit; Turquier, Frédéric; Hoc, Thierry; Brieu, Mathias

2018-06-01

Abdominal wall sheathing tissues are commonly involved in hernia formation. However, there is very limited work studying mechanics of all tissues from the same donor which prevents a complete understanding of the abdominal wall behavior and the differences in these tissues. The aim of this study was to investigate the differences between the mechanical properties of the linea alba and the anterior and posterior rectus sheaths from a macroscopic point of view. Eight full-thickness human anterior abdominal walls of both genders were collected and longitudinal and transverse samples were harvested from the three sheathing connective tissues. The total of 398 uniaxial tensile tests was conducted and the mechanical characteristics of the behavior (tangent rigidities for small and large deformations) were determined. Statistical comparisons highlighted heterogeneity and non-linearity in behavior of the three tissues under both small and large deformations. High anisotropy was observed under small and large deformations with higher stress in the transverse direction. Variabilities in the mechanical properties of the linea alba according to the gender and location were also identified. Finally, data dispersion correlated with microstructure revealed that macroscopic characterization is not sufficient to fully describe behavior. Microstructure consideration is needed. These results provide a better understanding of the mechanical behavior of the abdominal wall sheathing tissues as well as the directions for microstructure-based constitutive model. Copyright © 2018 Elsevier Ltd. All rights reserved.

Mechanical work for step-to-step transitions is a major determinant of the metabolic cost of human walking.

PubMed

Donelan, J Maxwell; Kram, Rodger; Kuo, Arthur D

2002-12-01

In the single stance phase of walking, center of mass motion resembles that of an inverted pendulum. Theoretically, mechanical work is not necessary for producing the pendular motion, but work is needed to redirect the center of mass velocity from one pendular arc to the next during the transition between steps. A collision model predicts a rate of negative work proportional to the fourth power of step length. Positive work is required to restore the energy lost, potentially exacting a proportional metabolic cost. We tested these predictions with humans (N=9) walking over a range of step lengths (0.4-1.1 m) while keeping step frequency fixed at 1.8 Hz. We measured individual limb external mechanical work using force plates, and metabolic rate using indirect calorimetry. As predicted, average negative and positive external mechanical work rates increased with the fourth power of step length (from 1 W to 38 W; r(2)=0.96). Metabolic rate also increased with the fourth power of step length (from 7 W to 379 W; r(2)=0.95), and linearly with mechanical work rate. Mechanical work for step-to-step transitions, rather than pendular motion itself, appears to be a major determinant of the metabolic cost of walking.

Influences of the shielding cylinder on the length of radio-frequency cold atmospheric plasma jets

NASA Astrophysics Data System (ADS)

Li, He-Ping; Li, Jing; Zhang, Xiao-Fei; Guo, Heng; Chen, Jian; Department of Engineering Physics Team

2017-10-01

Cold atmospheric plasma jets driven by a radio frequency power supply contain abundant species and complex chemical reactions, which have wide applications in the fields of materials processing and modifications, food engineering, bio-medical science, etc. Our previous experiments have shown that the total length of a radio-frequency cold atmospheric plasma (RF-CAP) jet can exceed 1 meter with the shielding of a quartz tube. However, the shielding mechanisms of the solid cylinder has not been studied systematically. In this study, a two-dimensional, quasi-steady fluid model is used to investigate the influences of the shielding tube on the length of the RF-CAP jets under different conditions. The simulation results show that the total jet length grows monotonously; while simultaneously, the jet length out of the tube shows a non-monotonic variation trend, with the increase of the tube length, which is in good agreement with the experimental observations. The shielding mechanisms of the solid cylinder on the RF-CAP jet is also discussed in detail based on the modeling results. This work was supported by the National Natural Science Foundation of China (11475103, 21627812), the National Key Research and Development Program of China (2016YFD0102106) and Tsinghua University Initiative Scientific Program (20161080108).

Relational particle models: I. Reconciliation with standard classical and quantum theory

NASA Astrophysics Data System (ADS)

Anderson, Edward

2006-04-01

This paper concerns the absolute versus relative motion debate. The Barbour and Bertotti (1982) work may be viewed as an indirectly set up relational formulation of a portion of Newtonian mechanics. I consider further direct formulations of this and argue that the portion in question—universes with zero total angular momentum that are conservative and with kinetic terms that are (homogeneous) quadratic in their velocities—is capable of accommodating a wide range of classical physics phenomena. Furthermore, as I develop in paper II, this relational particle model is a useful toy model for canonical general relativity. I consider what happens if one quantizes relational rather than absolute mechanics, indeed whether the latter is misleading. By exploiting Jacobi coordinates, I show how to access many examples of quantized relational particle models and then interpret these from a relational perspective. By these means, previous suggestions of bad semiclassicality for such models can be eluded. I show how small (particle number) universe relational particle model examples display eigenspectrum truncation, gaps, energy interlocking and counterbalanced total angular momentum. These features mean that these small universe models make interesting toy models for some aspects of closed-universe quantum cosmology. Meanwhile, these features do not compromise the recovery of reality as regards the practicalities of experimentation in a large universe such as our own.

A novel method for preparation of high dense tetragonal Li7La3Zr2O12

NASA Astrophysics Data System (ADS)

Zhao, Pengcheng; Wen, Yuehua; Cheng, Jie; Cao, Gaoping; Jin, Zhaoqing; Ming, Hai; Xu, Yan; Zhu, Xiayu

2017-03-01

For conventional preparation methods of Li7La3Zr2O12 (LLZO) solid state electrolytes, there is a stereotype that higher density always comes from higher pressure enforced upon the LLZO pellets. In this paper, a different way with an auto-consolidation mechanism is provided and discussed. No pressing operations are employed during the whole preparation process. Due to the surface tension of liquid melted Li2O at sintering temperature, LLZO particles could aggregate together freely and automatically. The preparation process for dense LLZO is greatly simplified. A dense tetragonal LLZO with high relative density about 93% has been prepared successfully by this auto-consolidation method. And there are no voids observed in the SEM images. At 30 °C, the total conductivity is about 5.67 × 10-5 S cm-1, which is the highest one for tetragonal LLZO in the reported issues, even two times higher than that prepared by hot-pressing method. The activation energy for total conductivity is ∼0.35 eV atom-1 at 30-120 °C, slightly lower than the previous reported values. This work sheds light on the understanding of the consolidation mechanism for solid electrolytes and suggests a reliable route to syhthesize cemanic solid electrolytes.

Precipitation recycling as a mechanism for ecoclimatological stability through local and non-local interactions

NASA Astrophysics Data System (ADS)

Dominguez, Francina

This study is the first to analyze the mechanisms that drive precipitation recycling variability at the daily to intraseasonal timescale. A new Dynamic Precipitation Recycling model is developed which, unlike previous models, includes the moisture storage term in the equation of conservation of atmospheric moisture. As shown using scaling analysis, the moisture storage term is non-negligible at small time scales, so the new model enables us to analyze precipitation recycling variability at shorter timescales than traditional models. The daily to intraseasonal analysis enables us to uncover key relationships between recycling and the moisture and energy fluxes. In the second phase of this work, a spatiotemporal analysis of daily precipitation recycling is performed over two regions of North America: the Midwestern United States, and the North American Monsoon System (NAMS) region. These regions were chosen because they present contrasting land-atmosphere interactions. Different physical mechanisms drive precipitation recycling in each region. In the Midwestern United States, evapotranspiration is not significantly affected by soil moisture anomalies, and there is a high recycling ratio during periods of reduced total precipitation. The reason is that, during periods of drier atmospheric conditions, transpiration will continue to provide moisture to the overlying atmosphere and contribute to total rainfall. Consequently, precipitation recycling variability in not driven by changes in evapotranspiration. Precipitable water, sensible heat and moisture fluxes are the main drivers of recycling variability in the Midwest. However, the drier soil moisture conditions over the NAMS region limit evapotranspiration, which will drive recycling variability. In this region, evapotranspiration becomes an important contribution to precipitation after Monsoon onset when total precipitation and evapotranspiration are highest. The precipitation recycling process in the NAMS region relocates moisture from regions of high evapotranspiration like the seasonally dry tropical forests of Mexico to drier regions downwind. During long monsoons, when soil moisture is abundant for a prolonged period of time, precipitation recycling significantly contributes to precipitation during periods of reduced total rainfall. In both the moisture abundant Midwestern region and the drier NAMS region, precipitation recycling plays an important role in maintaining a favorable hydroclimatological environment for vegetation.

On heart rate variability and autonomic activity in homeostasis and in systemic inflammation.

PubMed

Scheff, Jeremy D; Griffel, Benjamin; Corbett, Siobhan A; Calvano, Steve E; Androulakis, Ioannis P

2014-06-01

Analysis of heart rate variability (HRV) is a promising diagnostic technique due to the noninvasive nature of the measurements involved and established correlations with disease severity, particularly in inflammation-linked disorders. However, the complexities underlying the interpretation of HRV complicate understanding the mechanisms that cause variability. Despite this, such interpretations are often found in literature. In this paper we explored mathematical modeling of the relationship between the autonomic nervous system and the heart, incorporating basic mechanisms such as perturbing mean values of oscillating autonomic activities and saturating signal transduction pathways to explore their impacts on HRV. We focused our analysis on human endotoxemia, a well-established, controlled experimental model of systemic inflammation that provokes changes in HRV representative of acute stress. By contrasting modeling results with published experimental data and analyses, we found that even a simple model linking the autonomic nervous system and the heart confound the interpretation of HRV changes in human endotoxemia. Multiple plausible alternative hypotheses, encoded in a model-based framework, equally reconciled experimental results. In total, our work illustrates how conventional assumptions about the relationships between autonomic activity and frequency-domain HRV metrics break down, even in a simple model. This underscores the need for further experimental work towards unraveling the underlying mechanisms of autonomic dysfunction and HRV changes in systemic inflammation. Understanding the extent of information encoded in HRV signals is critical in appropriately analyzing prior and future studies. Copyright © 2014 Elsevier Inc. All rights reserved.

On heart rate variability and autonomic activity in homeostasis and in systemic inflammation

PubMed Central

Scheff, Jeremy D.; Griffel, Benjamin; Corbett, Siobhan A.; Calvano, Steve E.; Androulakis, Ioannis P.

2014-01-01

Analysis of heart rate variability (HRV) is a promising diagnostic technique due to the noninvasive nature of the measurements involved and established correlations with disease severity, particularly in inflammation-linked disorders. However, the complexities underlying the interpretation of HRV complicate understanding the mechanisms that cause variability. Despite this, such interpretations are often found in literature. In this paper we explored mathematical modeling of the relationship between the autonomic nervous system and the heart, incorporating basic mechanisms such as perturbing mean values of oscillating autonomic activities and saturating signal transduction pathways to explore their impacts on HRV. We focused our analysis on human endotoxemia, a well-established, controlled experimental model of systemic inflammation that provokes changes in HRV representative of acute stress. By contrasting modeling results with published experimental data and analyses, we found that even a simple model linking the autonomic nervous system and the heart confound the interpretation of HRV changes in human endotoxemia. Multiple plausible alternative hypotheses, encoded in a model-based framework, equally reconciled experimental results. In total, our work illustrates how conventional assumptions about the relationships between autonomic activity and frequency-domain HRV metrics break down, even in a simple model. This underscores the need for further experimental work towards unraveling the underlying mechanisms of autonomic dysfunction and HRV changes in systemic inflammation. Understanding the extent of information encoded in HRV signals is critical in appropriately analyzing prior and future studies. PMID:24680646

Multiscale Concrete Modeling of Aging Degradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammi, Yousseff; Gullett, Philipp; Horstemeyer, Mark F.

In this work a numerical finite element framework is implemented to enable the integration of coupled multiscale and multiphysics transport processes. A User Element subroutine (UEL) in Abaqus is used to simultaneously solve stress equilibrium, heat conduction, and multiple diffusion equations for 2D and 3D linear and quadratic elements. Transport processes in concrete structures and their degradation mechanisms are presented along with the discretization of the governing equations. The multiphysics modeling framework is theoretically extended to the linear elastic fracture mechanics (LEFM) by introducing the eXtended Finite Element Method (XFEM) and based on the XFEM user element implementation of Ginermore » et al. [2009]. A damage model that takes into account the damage contribution from the different degradation mechanisms is theoretically developed. The total contribution of damage is forwarded to a Multi-Stage Fatigue (MSF) model to enable the assessment of the fatigue life and the deterioration of reinforced concrete structures in a nuclear power plant. Finally, two examples are presented to illustrate the developed multiphysics user element implementation and the XFEM implementation of Giner et al. [2009].« less

Effects of glucose load on cognitive functions in elderly people.

PubMed

van der Zwaluw, Nikita L; van de Rest, Ondine; Kessels, Roy P C; de Groot, Lisette C P G M

2015-02-01

Glucose is the main fuel for the brain, and manipulation of the glucose supply may consequently affect brain function. The present review was conducted to provide an overview of studies that investigated the acute effects of glucose load on memory and other cognitive functions in elderly people. The effects of sucrose on cognition and suggested mechanisms were also explored. A total of twenty studies met the inclusion criteria. In the majority of studies, episodic memory was investigated and a beneficial role for glucose in that specific cognitive domain was suggested. Other cognitive domains, i.e., working memory, semantic memory, visual memory, information-processing speed, attention, executive function, and visual/spatial function, have been studied less frequently and evidence for a beneficial effect of glucose was equivocal. Mechanisms are suggested to be mainly related to the human body's need for glucose as a metabolic substrate for physiological mechanisms in both central and peripheral processes. © The Author(s) 2015. Published by Oxford University Press on behalf of the International Life Sciences Institute. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

ISO 9001 in a neonatal intensive care unit (NICU).

PubMed

Vitner, Gad; Nadir, Erez; Feldman, Michael; Yurman, Shmuel

2011-01-01

The aim of this paper is to present the process for approving and certifying a neonatal intensive care unit to ISO 9001 standards. The process started with the department head's decision to improve services quality before deciding to achieve ISO 9001 certification. Department processes were mapped and quality management mechanisms were developed. Process control and performance measurements were defined and implemented to monitor the daily work. A service satisfaction review was conducted to get feedback from families. In total, 28 processes and related work instructions were defined. Process yields showed service improvements. Family satisfaction improved. The paper is based on preparing only one neonatal intensive care unit to the ISO 9001 standard. The case study should act as an incentive for hospital managers aiming to improve service quality based on the ISO 9001 standard. ISO 9001 is becoming a recommended tool to improve clinical service quality.

Work stress, poor recovery and burnout in teachers.

PubMed

Gluschkoff, K; Elovainio, M; Kinnunen, U; Mullola, S; Hintsanen, M; Keltikangas-Järvinen, L; Hintsa, T

2016-10-01

Both work stress and poor recovery have been shown to contribute to the development of burnout. However, the role of recovery as a mediating mechanism that links work stress to burnout has not been sufficiently addressed in research. To examine recovery as a mediator in the relationship between work stress and burnout among teachers. A cross-sectional study of Finnish primary school teachers, in whom burnout was measured with the Maslach Burnout Inventory-General Survey and work stress was conceptualized using the effort-reward imbalance (ERI) model. Recovery was measured with the Recovery Experience Questionnaire and the Jenkins Sleep Problems Scale. Multiple linear regression analyses and bootstrap mediation analyses adjusted for age, gender and total working hours were performed. Among the 76 study subjects, high ERI was associated with burnout and its dimensions of exhaustion, cynicism and reduced professional efficacy. Poor recovery experiences, in terms of low relaxation during leisure time, partially mediated the relationship between ERI and reduced professional efficacy. Sleep problems, in the form of non-restorative sleep, partially mediated the relationship between ERI and both burnout and exhaustion. Supporting a balance between effort and reward at work may enhance leisure time recovery and improve sleep quality, as well as help to reduce burnout rates. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Microstructure and Mechanical Properties of Porous Mullite

NASA Astrophysics Data System (ADS)

Hsiung, Chwan-Hai Harold

Mullite (3 Al2O3 : 2 SiO2) is a technologically important ceramic due to its thermal stability, corrosion resistance, and mechanical robustness. One variant, porous acicular mullite (ACM), has a unique needle-like microstructure and is the material platform for The Dow Chemical Company's diesel particulate filter AERIFY(TM). The investigation described herein focuses on the microstructure-mechanical property relationships in acicular mullites as well as those with traditional porous microstructures with the goal of illuminating the critical factors in determining their modulus, strength, and toughness. Mullites with traditional pore morphologies were made to serve as references via slipcasting of a kaolinite-alumina-starch slurry. The starch was burned out to leave behind a pore network, and the calcined body was then reaction-sintered at 1600C to form mullite. The samples had porosities of approximately 60%. Pore size and shape were altered by using different starch templates, and pore size was found to influence the stiffness and toughness. The ACM microstructure was varied along three parameters: total porosity, pore size, and needle size. Total porosity was found to dominate the mechanical behavior of ACM, while increases in needle and pore size increased the toughness at lower porosities. ACM was found to have much improved (˜130%) mechanical properties relative to its non-acicular counterpart at the same porosity. A second set of investigations studied the role of the intergranular glassy phase which wets the needle intersections of ACM. Removal of the glassy phase via an HF etch reduced the mechanical properties by ˜30%, highlighting the intergranular phase's importance to the enhanced mechanical properties of ACM. The composition of the glassy phase was altered by doping the ACM precursor with magnesium and neodymium. Magnesium doping resulted in ACM with greatly reduced fracture strength and toughness. Studies showed that the mechanical properties of the two doped intergranular glasses and their interfaces with mullite were quite similar. The reductions in strength and toughness were traced to differences in the ACM network structure and mass-distribution that are hypothesized to result from dopant-altered ACM nucleation and growth kinetics. X-ray computed tomography, a non-destructive 3-D imaging technique, played a key role in this work, enabling the measurement of needle diameters, quantification of the ACM structural network, and finite element analysis of ACM's mechanical response.

The Mechanization of Work.

ERIC Educational Resources Information Center

Ginzberg, Eli

1982-01-01

Discusses how mechanization of work has been treated by economists, what its effect has been on the past U.S. economy, and what its future effect is likely to be. Emphasizes the impact of mechanization on the shifting structure and character of the labor force and evolution of the work environment. (Author/JN)

Time-dependent deformation of gas shales - role of rock framework versus reservoir fluids

NASA Astrophysics Data System (ADS)

Hol, Sander; Zoback, Mark

2013-04-01

Hydraulic fracturing operations are generally performed to achieve a fast, drastic increase of permeability and production rates. Although modeling of the underlying short-term mechanical response has proven successful via conventional geomechanical approaches, predicting long-term behavior is still challenging as the formation interacts physically and chemically with the fluids present in-situ. Recent experimental work has shown that shale samples subjected to a change in effective stress deform in a time-dependent manner ("creep"). Although the magnitude and nature of this behavior is strongly related to the composition and texture of the sample, also the choice of fluid used in the experiments affects the total strain response - strongly adsorbing fluids result in more, recoverable creep. The processes underlying time-dependent deformation of shales under in-situ stresses, and the long-term impact on reservoir performance, are at present poorly understood. In this contribution, we report triaxial mechanical tests, and theoretical/thermodynamic modeling work with the aim to identify and describe the main mechanisms that control time-dependent deformation of gas shales. In particular, we focus on the role of the shale solid framework versus the type and pressure of the present pore fluid. Our experiments were mainly performed on Eagle Ford Shale samples. The samples were subjected to cycles of loading and unloading, first in the dry state, and then again after equilibrating them with (adsorbing) CO2 and (non-adsorbing) He at fluid pressures of 4 MPa. Stresses were chosen close to those persisting under in-situ conditions. The results of our tests demonstrate that likely two main types of deformation mechanisms operate that relate to a) the presence of microfractures as a dominating feature in the solid framework of the shale, and b) the adsorbing potential of fluids present in the nanoscale voids of the shale. To explain the role of adsorption in the observed compaction creep, we postulate a serial coupling between 1) stress-driven desorption of the fluid species, 2) diffusion of the desorbed species out of the solid, and 3) consequent shrinkage. We propose a model in which the total shrinkage of the solid (Step 3) that is measured as bulk compaction, is driven by a change in stress state (Step 1), and evolves in time controlled by the diffusion characteristics of the system (Step 2). Our experimental and modeling study shows that both the nature of the solid framework of the shale, as well as the type and pressure of pore fluids affect the long-term in-situ mechanical behavior of gas shale reservoirs.

Applications and assessment of QM:QM electronic embedding using generalized asymmetric Mulliken atomic charges.

PubMed

Parandekar, Priya V; Hratchian, Hrant P; Raghavachari, Krishnan

2008-10-14

Hybrid QM:QM (quantum mechanics:quantum mechanics) and QM:MM (quantum mechanics:molecular mechanics) methods are widely used to calculate the electronic structure of large systems where a full quantum mechanical treatment at a desired high level of theory is computationally prohibitive. The ONIOM (our own N-layer integrated molecular orbital molecular mechanics) approximation is one of the more popular hybrid methods, where the total molecular system is divided into multiple layers, each treated at a different level of theory. In a previous publication, we developed a novel QM:QM electronic embedding scheme within the ONIOM framework, where the model system is embedded in the external Mulliken point charges of the surrounding low-level region to account for the polarization of the model system wave function. Therein, we derived and implemented a rigorous expression for the embedding energy as well as analytic gradients that depend on the derivatives of the external Mulliken point charges. In this work, we demonstrate the applicability of our QM:QM method with point charge embedding and assess its accuracy. We study two challenging systems--zinc metalloenzymes and silicon oxide cages--and demonstrate that electronic embedding shows significant improvement over mechanical embedding. We also develop a modified technique for the energy and analytic gradients using a generalized asymmetric Mulliken embedding method involving an unequal splitting of the Mulliken overlap populations to offer improvement in situations where the Mulliken charges may be deficient.

A Mechanical Coil Insertion System for Endovascular Coil Embolization of Intracranial Aneurysms

PubMed Central

Haraguchi, K.; Miyachi, S.; Matsubara, N.; Nagano, Y.; Yamada, H.; Marui, N.; Sano, A.; Fujimoto, H.; Izumi, T.; Yamanouchi, T.; Asai, T.; Wakabayashi, T.

2013-01-01

Summary Like other fields of medicine, robotics and mechanization might be introduced into endovascular coil embolization of intracranial aneurysms for effective treatment. We have already reported that coil insertion force could be smaller and more stable when the coil delivery wire is driven mechanically at a constant speed. Another background is the difficulty in synchronizing operators' minds and hands when two operators control the microcatheter and the coil respectively. We have therefore developed a mechanical coil insertion system enabling a single operator to insert coils at a fixed speed while controlling the microcatheter. Using our new system, the operator manipulated the microcatheter with both hands and drove the coil using foot switches simultaneously. A delivery wire force sensor previously reported was used concurrently, allowing the operator to detect excessive stress on the wire. In vitro coil embolization was performed using three methods: simple mechanical advance of the coil; simple mechanical advance of the coil with microcatheter control; and driving (forward and backward) of the coil using foot switches in addition to microcatheter control. The system worked without any problems, and did not interfere with any procedures. In experimental coil embolization, delivery wire control using the foot switches as well as microcatheter manipulation helped to achieve successful insertion of coils. This system could offer the possibility of developing safer and more efficient coil embolization. Although we aim at total mechanization and automation of procedures in the future, microcatheter manipulation and synchronized delivery wire control are still indispensable using this system. PMID:23693038

Compensatory dynamics stabilize aggregate community properties in response to multiple types of perturbations.

PubMed

Brown, Bryan L; Downing, Amy L; Leibold, Mathew A

2016-08-01

Compensatory dynamics are an important suite of mechanisms that can stabilize community and ecosystem attributes in systems subject to environmental fluctuations. However, few experimental investigations of compensatory dynamics have addressed these mechanisms in systems of real-world complexity, and existing evidence relies heavily on correlative analyses, retrospective examination, and experiments in simple systems. We investigated the potential for compensatory dynamics to stabilize plankton communities in plankton mesocosm systems of real-world complexity. We employed four types of perturbations including two types of nutrient pulses, shading, and acidification. To quantify how communities responded to these perturbations, we used a measure of community-wide synchrony combined with spectral analysis that allowed us to assess timescale-specific community dynamics, for example, whether dynamics were synchronous at some timescales but compensatory at others. The 150-d experiment produced 32-point time series of all zooplankton taxa in the mesocosms. We then used those time series to evaluate total zooplankton biomass as an aggregate property and to evaluate community dynamics. For three of our four perturbation types, total zooplankton biomass was significantly less variable in systems with environmental variation than in constant environments. For the same three perturbation types, community-wide synchrony was much lower in fluctuating environments than in the constant environment, particularly at longer timescales (periods ≈ 60 d). Additionally, there were strong negative correlations between population temporal variances and the level of community-wide synchrony. Taken together, these results strongly imply that compensatory interactions between species stabilized total biomass in response to perturbations. Diversity did not differ significantly across either treatments or perturbation types, thus ruling out several classes of mechanisms driven by changes in diversity. We also used several pieces of secondary evidence to evaluate the particular mechanism behind compensatory responses since a wide variety of mechanisms are hypothesized to produce compensatory dynamics. We concluded that fluctuation dependent endogenous cycles that occur as a consequence of consumer-resource interactions in competitive communities were the most likely explanation for the compensatory dynamics observed in our experiment. As with our previous work, scale-dependent dynamics were also a key to understanding compensatory dynamics in these experimental communities. © 2016 by the Ecological Society of America.

Experimental estimation of energy absorption during heel strike in human barefoot walking.

PubMed

Baines, Patricia M; Schwab, A L; van Soest, A J

2018-01-01

Metabolic energy expenditure during human gait is poorly understood. Mechanical energy loss during heel strike contributes to this energy expenditure. Previous work has estimated the energy absorption during heel strike as 0.8 J using an effective foot mass model. The aim of our study is to investigate the possibility of determining the energy absorption by more directly estimating the work done by the ground reaction force, the force-integral method. Concurrently another aim is to compare this method of direct determination of work to the method of an effective foot mass model. Participants of our experimental study were asked to walk barefoot at preferred speed. Ground reaction force and lower leg kinematics were collected at high sampling frequency (3000 Hz; 1295 Hz), with tight synchronization. The work done by the ground reaction force is 3.8 J, estimated by integrating this force over the foot-ankle deformation. The effective mass model is improved by dropping the assumption that foot-ankle deformation is maximal at the instant of the impact force peak. On theoretical grounds it is clear that in the presence of substantial damping that peak force and peak deformation do not occur simultaneously. The energy absorption results, due the vertical force only, corresponding to the force-integral method is similar to the results of the improved application of the effective mass model (2.7 J; 2.5 J). However the total work done by the ground reaction force calculated by the force-integral method is significantly higher than that of the vertical component alone. We conclude that direct estimation of the work done by the ground reaction force is possible and preferable over the use of the effective foot mass model. Assuming that energy absorbed is lost, the mechanical energy loss of heel strike is around 3.8 J for preferred walking speeds (≈ 1.3 m/s), which contributes to about 15-20% of the overall metabolic cost of transport.

NCI at a Glance

Cancer.gov

This infographic provides a high-level overview of NCI's historical milestones, funding process, the NCI-designated cancer centers, and training numbers for fiscal year (FY) 2017. The work we do includes genomics, public health, clinical trials, surveillance, scientific review, basic research, funding, drug development, cancer research, survivorship research, and more. Funds available to the NCI in FY 2018 totaled $5.67 billion which reflects an increase of $254 million from the previous fiscal year. In FY 2017, NCI supported 3,795 emerging cancer researchers through training and career development grants and intramural research experiences (not including students and postdoctoral fellows supported by NCI research project grants, cancer center grants, and other non-training mechanisms).

[Palatograms and linguograms for studying misarticulation following surgery for tumors of the tongue and oral cavity floor].

PubMed

Lewandowski, Leszek

2006-01-01

This work deals with the mechanism of misarticulation following surgery for malignancies in the oral cavity. The underlying cause was dysfunction of the tongue due to partial or total resection, consequences of the resection of the mandible together with the oral cavity floor, or dysfunkction of the lower lip failing to seal the space of Donders. Anatomic alternations reveal themselves as shifts in the points of contact between structures of the articulation system noticeable on palatograms or linguograms. Limited mobility of tongue tip may affect speech, particularly in the case of sounds of the first and second articulation zone.

Demystification of Bell inequality

NASA Astrophysics Data System (ADS)

Khrennikov, Andrei

2009-08-01

The main aim of this review is to show that the common conclusion that Bell's argument implies that any attempt to proceed beyond quantum mechanics induces a nonlocal model was not totally justified. Our analysis of Bell's argument demonstrates that violation of Bell's inequality implies neither "death of realism" nor nonlocality. This violation is just a sign of non-Kolmogorovness of statistical data - impossibility to put statistical data collected in a few different experiments (corresponding to incompatible settings of polarization beam splitters) in one probability space. This inequality was well known in theoretical probability since 19th century (from works of Boole). We couple non-Kolmogorovness of data with design of modern detectors of photons.

Bringing Managed Care Incentives to Medicare's Fee-for-Service Sector

PubMed Central

Tompkins, Christopher P.; Wallack, Stanley S.; Bhalotra, Sarita; Chilingerian, Jon A.; Glavin, Mitchell P.V.; Ritter, Grant A.; Hodgkin, Dominic

1996-01-01

The Health Care Financing Administration (HCFA) could work with eligible physician organizations to generate savings in total reimbursements for their Medicare patients. Medicare would continue to reimburse all providers according to standard payment policies and mechanisms, and beneficiaries would retain the freedom to choose providers. However, implementation of new financial incentives, based on meeting targets called Group-Specific Volume Performance Standards (GVPS), would encourage cost-effective service delivery patterns. HCFA could use new and existing data systems to monitor access, utilization patterns, cost outcomes and quality of care. In short, HCFA could manage providers, who, in turn, would manage their patients' care. PMID:10165712

[The influence of tobacco-smoke toxic components on glucosaminoglycans in biologic tissues].

PubMed

Zurabashvili, D Z; Chanturiia, I R; Kapanadze, L R; Kikalishvili, B Iu; Daneliia, G G

2010-04-01

The aim of the work is detailed analysis of glucosaminoglikans and glukuronic acid in chisel tooth and molars of tobacco-smokers and non-smokers. The total number of 140 patients (tobacco-smokers - 60) by acute serous pulpit is investigated. The conducted quantative and qualitative analyzes show that tobacco-smokers tooth contains les glucosaminoglikans (chondroitinsulfats A and C) and more glucuronic acid than non-smokers individuals. The chisel tooth pulp contained considerably more glucuronic acid as compared with molars. These studies support the hypothesis of important role of cigarette smoke toxical components in the tooth support mechanisms. The studies are necessary to be held in different directions.

Mechanism of Na-Ion Storage in Hard Carbon Anodes Revealed by Heteroatom Doping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Zhifei; Bommier, Clement; Chong, Zhi Sen

Hard carbon is the candidate anode material for the commercialization of Na-ion batteries the batteries that by virtue of being constructed from inexpensive and abundant components open the door for massive scale up of battery-based storage of electrical energy. Holding back the development of these batteries is that a complete understanding of the mechanism of Na-ion storage in hard carbon has remained elusive. Although as an amorphous carbon, hard carbon possesses a subtle and complex structure composed of domains of layered rumpled sheets that have local order resembling graphene within each layer but complete disorder along the c-axis between layers.more » Here, we present two key discoveries: first that characteristics of hard carbon s structure can be modified systematically by heteroatom doping, and second, that these changes greatly affect Na-ion storage properties, which reveal the mechanisms for Na storage in hard carbon. Specifically, P, S and B doping was used to engineer the density of local defects in graphenic layers, and to modify the spacing between the layers. While opening the interlayer spacing through P or S doping extends the low-voltage capacity plateau, and increasing the defect concentration with P or B doping high first sodiation capacity is achieved. Furthermore, we observe that the highly defective B-doped hard carbon suffers a tremendous irreversible capacity in the first desodiation cycle. Our combined first principles calculations and experimental studies revealed a new trapping mechanism, showing that the high binding energies between B-doping induced defects and Na-ions are responsible for the irreversible capacity. The understanding generated in this work provides a totally new set of guiding principles for materials engineers working to optimize hard carbon for Na-ion battery applications.« less

A Three-Dimensional Kinematic and Kinetic Study of the College-Level Female Softball Swing

PubMed Central

Milanovich, Monica; Nesbit, Steven M.

2014-01-01

This paper quantifies and discusses the three-dimensional kinematic and kinetic characteristics of the female softball swing as performed by fourteen female collegiate amateur subjects. The analyses were performed using a three-dimensional computer model. The model was driven kinematically from subject swings data that were recorded with a multi-camera motion analysis system. Each subject used two distinct bats with significantly different inertial properties. Model output included bat trajectories, subject/bat interaction forces and torques, work, and power. These data formed the basis for a detailed analysis and description of fundamental swing kinematic and kinetic quantities. The analyses revealed that the softball swing is a highly coordinated and individual three-dimensional motion and subject-to-subject variations were significant in all kinematic and kinetic quantities. In addition, the potential effects of bat properties on swing mechanics are discussed. The paths of the hands and the centre-of-curvature of the bat relative to the horizontal plane appear to be important trajectory characteristics of the swing. Descriptions of the swing mechanics and practical implications are offered based upon these findings. Key Points The female softball swing is a highly coordinated and individual three-dimensional motion and subject-to-subject variations were significant in all kinematic and kinetic quantities. The paths of the grip point, bat centre-of-curvature, CG, and COP are complex yet reveal consistent patterns among subjects indicating that these patterns are fundamental components of the swing. The most important mechanical quantity relative to generating bat speed is the total work applied to the bat from the batter. Computer modeling of the softball swing is a viable means for study of the fundamental mechanics of the swing motion, the interactions between the batter and the bat, and the energy transfers between the two. PMID:24570623

Mechanism of Na-Ion Storage in Hard Carbon Anodes Revealed by Heteroatom Doping

DOE PAGES

Li, Zhifei; Bommier, Clement; Chong, Zhi Sen; ...

2017-05-23

Hard carbon is the candidate anode material for the commercialization of Na-ion batteries the batteries that by virtue of being constructed from inexpensive and abundant components open the door for massive scale up of battery-based storage of electrical energy. Holding back the development of these batteries is that a complete understanding of the mechanism of Na-ion storage in hard carbon has remained elusive. Although as an amorphous carbon, hard carbon possesses a subtle and complex structure composed of domains of layered rumpled sheets that have local order resembling graphene within each layer but complete disorder along the c-axis between layers.more » Here, we present two key discoveries: first that characteristics of hard carbon s structure can be modified systematically by heteroatom doping, and second, that these changes greatly affect Na-ion storage properties, which reveal the mechanisms for Na storage in hard carbon. Specifically, P, S and B doping was used to engineer the density of local defects in graphenic layers, and to modify the spacing between the layers. While opening the interlayer spacing through P or S doping extends the low-voltage capacity plateau, and increasing the defect concentration with P or B doping high first sodiation capacity is achieved. Furthermore, we observe that the highly defective B-doped hard carbon suffers a tremendous irreversible capacity in the first desodiation cycle. Our combined first principles calculations and experimental studies revealed a new trapping mechanism, showing that the high binding energies between B-doping induced defects and Na-ions are responsible for the irreversible capacity. The understanding generated in this work provides a totally new set of guiding principles for materials engineers working to optimize hard carbon for Na-ion battery applications.« less

A three-dimensional kinematic and kinetic study of the college-level female softball swing.

PubMed

Milanovich, Monica; Nesbit, Steven M

2014-01-01

This paper quantifies and discusses the three-dimensional kinematic and kinetic characteristics of the female softball swing as performed by fourteen female collegiate amateur subjects. The analyses were performed using a three-dimensional computer model. The model was driven kinematically from subject swings data that were recorded with a multi-camera motion analysis system. Each subject used two distinct bats with significantly different inertial properties. Model output included bat trajectories, subject/bat interaction forces and torques, work, and power. These data formed the basis for a detailed analysis and description of fundamental swing kinematic and kinetic quantities. The analyses revealed that the softball swing is a highly coordinated and individual three-dimensional motion and subject-to-subject variations were significant in all kinematic and kinetic quantities. In addition, the potential effects of bat properties on swing mechanics are discussed. The paths of the hands and the centre-of-curvature of the bat relative to the horizontal plane appear to be important trajectory characteristics of the swing. Descriptions of the swing mechanics and practical implications are offered based upon these findings. Key PointsThe female softball swing is a highly coordinated and individual three-dimensional motion and subject-to-subject variations were significant in all kinematic and kinetic quantities.The paths of the grip point, bat centre-of-curvature, CG, and COP are complex yet reveal consistent patterns among subjects indicating that these patterns are fundamental components of the swing.The most important mechanical quantity relative to generating bat speed is the total work applied to the bat from the batter.Computer modeling of the softball swing is a viable means for study of the fundamental mechanics of the swing motion, the interactions between the batter and the bat, and the energy transfers between the two.

Assessment and validation of CT scanogram to compare per-operative and post-operative mechanical axis after navigated total knee replacement

PubMed Central

Jain, Sunil

2008-01-01

Our objective was to assess and validate low-dose computed tomography (CT) scanogram as a post-operative imaging modality to measure the mechanical axis after navigated total knee replacement. A prospective study was performed to compare intra-operative and post-operative mechanical axis after navigated total knee replacements. All consecutive patients who underwent navigated total knee replacement between May and December 2006 were included. The intra-operative final axis was recorded, and post-operatively a CT scanogram of lower limbs was performed. The mechanical axis was measured and compared against the intra-operative measurement. There were 15 patients ranging in age from 57 to 80 (average 70) years. The average final intra-operative axis was 0.56° varus (4° varus to 1.5° valgus) and post-operative CT scanogram axis was 0.52° varus (3.1° varus to 1.8° valgus). The average deviation from final axes to CT scanogram axes was 0.12° valgus with a correlation coefficient of 0.9. Our study suggests that CT scanogram is an imaging modality with reasonable accuracy for measuring mechanical axis despite significantly low radiation. It also confirms a high level of correlation between intra-operative and post-operative mechanical axis after navigated total knee replacement. PMID:18696064

A review of 3D first-pass, whole-heart, myocardial perfusion cardiovascular magnetic resonance.

PubMed

Fair, Merlin J; Gatehouse, Peter D; DiBella, Edward V R; Firmin, David N

2015-08-01

A comprehensive review is undertaken of the methods available for 3D whole-heart first-pass perfusion (FPP) and their application to date, with particular focus on possible acceleration techniques. Following a summary of the parameters typically desired of 3D FPP methods, the review explains the mechanisms of key acceleration techniques and their potential use in FPP for attaining 3D acquisitions. The mechanisms include rapid sequences, non-Cartesian k-space trajectories, reduced k-space acquisitions, parallel imaging reconstructions and compressed sensing. An attempt is made to explain, rather than simply state, the varying methods with the hope that it will give an appreciation of the different components making up a 3D FPP protocol. Basic estimates demonstrating the required total acceleration factors in typical 3D FPP cases are included, providing context for the extent that each acceleration method can contribute to the required imaging speed, as well as potential limitations in present 3D FPP literature. Although many 3D FPP methods are too early in development for the type of clinical trials required to show any clear benefit over current 2D FPP methods, the review includes the small but growing quantity of clinical research work already using 3D FPP, alongside the more technical work. Broader challenges concerning FPP such as quantitative analysis are not covered, but challenges with particular impact on 3D FPP methods, particularly with regards to motion effects, are discussed along with anticipated future work in the field.

Onset of decreased heart work is correlated with increased heart rate and shortened QT interval in high-carbohydrate fed overweight rats.

PubMed

Durak, Aysegul; Olgar, Yusuf; Tuncay, Erkan; Karaomerlioglu, Irem; Kayki Mutlu, Gizem; Arioglu Inan, Ebru; Altan, Vecdi Melih; Turan, Belma

2017-11-01

Mechanical activity of the heart is adversely affected in metabolic syndrome (MetS) characterized by increased body mass and marked insulin resistance. Herein, we examined the effects of high carbohydrate intake on cardiac function abnormalities by evaluating in situ heart work, heart rate, and electrocardiograms (ECGs) in rats. MetS was induced in male Wistar rats by adding 32% sucrose to drinking water for 22-24 weeks and was confirmed by insulin resistance, increased body weight, increased blood glucose and serum insulin, and increased systolic and diastolic blood pressures in addition to significant loss of left ventricular integrity and increased connective tissue around myofibrils. Analysis of in situ ECG recordings showed a markedly shortened QT interval and decreased QRS amplitude with increased heart rate. We also observed increased oxidative stress and decreased antioxidant defense characterized by decreases in serum total thiol level and attenuated paraoxonase and arylesterase activities. Our data indicate that increased heart rate and a shortened QT interval concomitant with higher left ventricular developed pressure in response to β-adrenoreceptor stimulation as a result of less cyclic AMP release could be regarded as a natural compensation mechanism in overweight rats with MetS. In addition to the persistent insulin resistance and obesity associated with MetS, one should consider the decreased heart work, increased heart rate, and shortened QT interval associated with high carbohydrate intake, which may have more deleterious effects on the mammalian heart.

20 CFR 410.426 - Determining total disability: Age, education, and work experience criteria.

Code of Federal Regulations, 2011 CFR

2011-04-01

... ADMINISTRATION FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, TITLE IV-BLACK LUNG BENEFITS (1969- ) Total Disability or Death Due to Pneumoconiosis § 410.426 Determining total disability: Age, education, and work...

Stability Error Budget for an Aggressive Coronagraph on a 3.8 m Telescope

NASA Technical Reports Server (NTRS)

Shaklan, Stuart B.; Marchen, Luis; Krist, John; Rud, Mayer

2011-01-01

We evaluate in detail the stability requirements for a band-limited coronagraph with an inner working angle as small as 2 lambda/D coupled to an off-axis, 3.8-m diameter telescope. We have updated our methodologies since presenting a stability error budget for the Terrestrial Planet Finder Coronagraph mission that worked at 4 lambda/D and employed an 8th-order mask to reduce aberration sensitives. In the previous work, we determined the tolerances relative to the total light leaking through the coronagraph. Now, we separate the light into a radial component, which is readily separable from a planet signal, and an azimuthal component, which is easily confused with a planet signal. In the current study, throughput considerations require a 4th-order coronagraph. This, combined with the more aggressive working angle, places extraordinarily tight requirements on wavefront stability and opto-mechanical stability. We find that the requirements are driven mainly by coma that leaks around the coronagraph mask and mimics the localized signal of a planet, and pointing errors that scatter light into the background, decreasing SNR. We also show how the requirements would be relaxed if a low-order aberration detection system could be employed.

Work stressors and partner social undermining: Comparing negative affect and psychological detachment as mechanisms.

PubMed

Meier, Laurenz L; Cho, Eunae

2018-05-14

With the mounting evidence that employees' work experiences spill over into the family domain and cross over to family members, it is important to understand the underlying mechanism through which work experiences affect the family domain and what factors may alleviate the adverse impact of work stress. Expanding previous research that mainly focused on the affect-based mechanism (negative affect), the present research investigated a resource-based mechanism (psychological detachment from work) in the relationship linking two work stressors (high workload and workplace incivility) with social undermining toward the partner at home. We also explored the relative strength of the mediating effects of the two mechanisms. In addition, we tested whether relationship satisfaction moderates the proposed effect of detachment on partner undermining. We tested these research questions using two studies with differing designs: a five-wave longitudinal study (N = 470) and a multisource study (N = 131). The results suggest that stressful work experiences affect the family domain via lack of detachment as well as negative affect, that the two pathways have comparable strength, and that high relationship satisfaction mitigates the negative effect of lack of detachment on partner undermining. In sum, this research extends the spillover-crossover model by establishing that poor psychological detachment from work during leisure time is an additional mechanism that links work and family. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Effects of soil mechanical resistance on nematode community structure under conventional sugarcane and remaining of Atlantic Forest.

PubMed

de Oliveira Cardoso, Mércia; Pedrosa, Elvira M R; Rolim, Mário M; Silva, Enio F F E; de Barros, Patrícia A

2012-06-01

Nematodes present high potential as a biological indicator of soil quality. In this work, it was evaluated relations between soil physical properties and nematode community under sugarcane cropping and remaining of Atlantic Forest areas in Northeastern Pernambuco, Brazil. Soil samples were collected from September to November 2009 along two 200-m transects in both remaining of Atlantic Forest and sugarcane field at deeps of 0-10, 10-20, 20-30, 30-40, and 40-50 cm. For soil characterization, it was carried out analysis of soil size, water content, total porosity, bulk density, and particle density. The level of soil mechanical resistance was evaluated through a digital penetrometer. Nematodes were extracted per 300 cm(3) of soil through centrifugal flotation in sucrose being quantified, classified according trophic habit, and identified in level of genus or family. Data were analyzed using Pearson correlation at 5% of probability. Geostatistical analysis showed that the penetration resistance, water content, total porosity, and bulk density on both forest and cultivated area exhibited spatial dependence at the sampled scale, and their experimental semivariograms were fitted to spherical and exponential models. In forest area, the ectoparasites and free-living nematodes exhibited spherical model. In sugarcane field, the soil nematodes exhibited pure nugget effect. Pratylenchus sp. and Helicotylenchus sp. were prevalent in sugarcane field, but in forest, there was prevalence of Dorylaimidae and Rhabditidae. Total amount of nematode did not differ between environments; however, community trophic structure in forest presented prevalence of free-living nematodes: omnivores followed by bacterial-feeding soil nematodes, while plant-feeding nematodes were prevalent in sugarcane field. The nematode diversity was higher in the remaining of Atlantic Forest. However, the soil mechanical resistance was higher under sugarcane cropping, affecting more directly the free-living nematodes; especially Dorylaimidae which was the most sensible to changes in soil physical properties.

Sediment Transport Dynamics and Bedform Evolution During Unsteady Flows

NASA Astrophysics Data System (ADS)

Hu, H.; Parsons, D. R.; Ockelford, A.; Hardy, R. J.; Ashworth, P. J.; Best, J.

2016-12-01

Dunes are ubiquitous features in sand bed rivers and estuaries, and their formation, growth and kinematics play a dominant role in boundary flow structure, flow resistance and sediment transport processes. However, bedform evolution and dynamics during the rising/falling limb of a flood wave remain poorly understood. Herein, we report on a series of flume experiments, undertaken at the University of Hull's Total Environment Simulator flume/wave tank facility, with imposed flow variations and different hydrographs: i) a sudden (shock) change, ii) a fast flood wave and iii) a slow flood wave. Our analysis shows that, because of changes of sediment transport mechanisms with discharge, the sediment flux rather than bedform migration rate is a more appropriate parameter to relate to transport stage. This is particularly the case during bedload transport dominated periods at lower flow discharge, where a strong power law relationship was detected. In terms of varying processes across the hydrograph limbs, bedform evolution during the rising limb is dominated not only by bedform amalgamation but also by the washing out of smaller-scale bedforms. Furthermore, bedform growth is independent of the rising rate of the hydrograph limb, while evolution of bedform decay is affected by the rate of discharge decrease. This results in an anticlockwise hysteresis between transport stage and total flux was found in fast wave experiment, indicating a significant role of the change in sediment transport mechanisms on bedform evolution. Moreover, analysis on the variation of deformation fraction (F, ratio of the deformation flux to the total bed material flux) suggests that net degradation of the bed enhances bedform deformation and leads to a higher F ( 0.65). This work extends our knowledge on how dunes generate and develop under variable flows and has begun to explore how variations in transport stage can be coupled with the variation in sediment transport mechanisms, and/or sediment supply which can help improve the modelling of sediment transport processes.

A multi-particle crushing apparatus for studying rock fragmentation due to repeated impacts

NASA Astrophysics Data System (ADS)

Huang, S.; Mohanty, B.; Xia, K.

2017-12-01

Rock crushing is a common process in mining and related operations. Although a number of particle crushing tests have been proposed in the literature, most of them are concerned with single-particle crushing, i.e., a single rock sample is crushed in each test. Considering the realistic scenario in crushers where many fragments are involved, a laboratory crushing apparatus is developed in this study. This device consists of a Hopkinson pressure bar system and a piston-holder system. The Hopkinson pressure bar system is used to apply calibrated dynamic loads to the piston-holder system, and the piston-holder system is used to hold rock samples and to recover fragments for subsequent particle size analysis. The rock samples are subjected to three to seven impacts under three impact velocities (2.2, 3.8, and 5.0 m/s), with the feed size of the rock particle samples limited between 9.5 and 12.7 mm. Several key parameters are determined from this test, including particle size distribution parameters, impact velocity, loading pressure, and total work. The results show that the total work correlates well with resulting fragmentation size distribution, and the apparatus provides a useful tool for studying the mechanism of crushing, which further provides guidelines for the design of commercial crushers.

Modeling elasto-viscoplasticity in a consistent phase field framework

DOE PAGES

Cheng, Tian -Le; Wen, You -Hai; Hawk, Jeffrey A.

2017-05-19

Existing continuum level phase field plasticity theories seek to solve plastic strain by minimizing the shear strain energy. However, rigorously speaking, for thermodynamic consistency it is required to minimize the total strain energy unless there is proof that hydrostatic strain energy is independent of plastic strain which is unfortunately absent. In this work, we extend the phase-field microelasticity theory of Khachaturyan et al. by minimizing the total elastic energy with constraint of incompressibility of plastic strain. We show that the flow rules derived from the Ginzburg-Landau type kinetic equation can be in line with Odqvist's law for viscoplasticity and Prandtl-Reussmore » theory. Free surfaces (external surfaces or internal cracks/voids) are treated in the model. Deformation caused by a misfitting spherical precipitate in an elasto-plastic matrix is studied by large-scale three-dimensional simulations in four different regimes in terms of the matrix: (a) elasto-perfectly-plastic, (b) elastoplastic with linear hardening, (c) elastoplastic with power-law hardening, and (d) elasto-perfectly-plastic with a free surface. The results are compared with analytical/numerical solutions of Lee et al. for (a-c) and analytical solution derived in this work for (d). Additionally, the J integral of a fixed crack is calculated in the phase-field model and discussed in the context of fracture mechanics.« less

Modeling elasto-viscoplasticity in a consistent phase field framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Tian -Le; Wen, You -Hai; Hawk, Jeffrey A.

Existing continuum level phase field plasticity theories seek to solve plastic strain by minimizing the shear strain energy. However, rigorously speaking, for thermodynamic consistency it is required to minimize the total strain energy unless there is proof that hydrostatic strain energy is independent of plastic strain which is unfortunately absent. In this work, we extend the phase-field microelasticity theory of Khachaturyan et al. by minimizing the total elastic energy with constraint of incompressibility of plastic strain. We show that the flow rules derived from the Ginzburg-Landau type kinetic equation can be in line with Odqvist's law for viscoplasticity and Prandtl-Reussmore » theory. Free surfaces (external surfaces or internal cracks/voids) are treated in the model. Deformation caused by a misfitting spherical precipitate in an elasto-plastic matrix is studied by large-scale three-dimensional simulations in four different regimes in terms of the matrix: (a) elasto-perfectly-plastic, (b) elastoplastic with linear hardening, (c) elastoplastic with power-law hardening, and (d) elasto-perfectly-plastic with a free surface. The results are compared with analytical/numerical solutions of Lee et al. for (a-c) and analytical solution derived in this work for (d). Additionally, the J integral of a fixed crack is calculated in the phase-field model and discussed in the context of fracture mechanics.« less

45 CFR 2543.84 - Contract Work Hours and Safety Standards Act.

Code of Federal Regulations, 2013 CFR

2013-10-01

... contracts and in excess of $2500 for other contracts that involve the employment of mechanics or laborers... Section 102 of the Act, each contractor shall be required to compute the wages of every mechanic and... to construction work and provides that no laborer or mechanic shall be required to work in...

45 CFR 2543.84 - Contract Work Hours and Safety Standards Act.

Code of Federal Regulations, 2011 CFR

2011-10-01

... contracts and in excess of $2500 for other contracts that involve the employment of mechanics or laborers... Section 102 of the Act, each contractor shall be required to compute the wages of every mechanic and... to construction work and provides that no laborer or mechanic shall be required to work in...

45 CFR 2543.84 - Contract Work Hours and Safety Standards Act.

Code of Federal Regulations, 2012 CFR

2012-10-01

... contracts and in excess of $2500 for other contracts that involve the employment of mechanics or laborers... Section 102 of the Act, each contractor shall be required to compute the wages of every mechanic and... to construction work and provides that no laborer or mechanic shall be required to work in...

48 CFR 52.222-4 - Contract Work Hours and Safety Standards-Overtime Compensation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... laborers or mechanics (see Federal Acquisition Regulation 22.300) shall require or permit them to work over... basic payroll records for all laborers and mechanics working on the contract during the contract and... the employment of laborers and mechanics and require subcontractors to include these provisions in any...

45 CFR 2543.84 - Contract Work Hours and Safety Standards Act.

Code of Federal Regulations, 2014 CFR

2014-10-01

... contracts and in excess of $2500 for other contracts that involve the employment of mechanics or laborers... Section 102 of the Act, each contractor shall be required to compute the wages of every mechanic and... to construction work and provides that no laborer or mechanic shall be required to work in...

Elucidating the nature and mechanism of tic improvement in tourette syndrome: a pilot study.

PubMed

Shprecher, David R; Gannon, Keenan; Agarwal, Nivedita; Shi, Xianfeng; Anderson, Jeffrey S

2014-01-01

For unclear reasons, many Tourette syndrome (TS) children report near-complete tic remission by young adulthood. Immature maturation of brain networks, observed with resting-state functional MRI (rs-fc-MRI) in adolescents and adults with TS, might evolve to a mature pattern in adults who experience tic improvement or remission. We explored the feasibility of testing this hypothesis in our population of young adult TS males, each with prior clinical assessments completed during childhood as part of a separate TS Association Genetics Consortium study. A total of 10 TS males (off tic suppressing drugs for at least 6 months) aged 19-32 years, mean follow-up interval 7.5 (2 to 13) years, and 11 neurologically normal controls were enrolled and underwent 3-Tesla structural and rs-fc-MRI sequences. The mean change in Yale Global Tic Severity Scale (YGTSS) was -31.5% (total) and -26.6% (YGTSS motor+vocal). Two subjects reported resolution of tic-related disability, with drops from mean 45 to 16.5 (YGTSS-total) and 25 to 11.5 (YGTSS motor+vocal.). Rs-fc-MRI revealed significantly increased connectivity between the ipsilateral anterior and mid cingulate cortex and striatum, increased connectivity between local connections, and decreased connectivity between more distant connections; representing an immature connectivity pattern. Similar to previous reports, we found immature patterns of functional connectivity in adult TS subjects. Despite a lack of complete tic remission, two subjects exhibited dramatic drops in tic severity that correlated with tic-related disability improvement. More work is needed to elucidate the mechanism of such dramatic improvement in TS.

Measurement-induced randomness and state-merging

NASA Astrophysics Data System (ADS)

Chakrabarty, Indranil; Deshpande, Abhishek; Chatterjee, Sourav

In this work we introduce the randomness which is truly quantum mechanical in nature arising as an act of measurement. For a composite classical system, we have the joint entropy to quantify the randomness present in the total system and that happens to be equal to the sum of the entropy of one subsystem and the conditional entropy of the other subsystem, given we know the first system. The same analogy carries over to the quantum setting by replacing the Shannon entropy by the von Neumann entropy. However, if we replace the conditional von Neumann entropy by the average conditional entropy due to measurement, we find that it is different from the joint entropy of the system. We call this difference Measurement Induced Randomness (MIR) and argue that this is unique of quantum mechanical systems and there is no classical counterpart to this. In other words, the joint von Neumann entropy gives only the total randomness that arises because of the heterogeneity of the mixture and we show that it is not the total randomness that can be generated in the composite system. We generalize this quantity for N-qubit systems and show that it reduces to quantum discord for two-qubit systems. Further, we show that it is exactly equal to the change in the cost quantum state merging that arises because of the measurement. We argue that for quantum information processing tasks like state merging, the change in the cost as a result of discarding prior information can also be viewed as a rise of randomness due to measurement.

Racial Differences in the Association Between Night Shift Work and Melatonin Levels Among Women

PubMed Central

Bhatti, Parveen; Mirick, Dana K.; Davis, Scott

2013-01-01

Reduced suppression of melatonin in response to working the night shift among people of Asian ancestry has been suggested as a possible explanation for the null results observed in a recent analysis of shift work and breast cancer risk in a Chinese cohort. The authors analyzed the impact of Asian versus white race on previously reported differences in urinary 6-sulfatoxymelatonin levels in a 2003–2008 study in Seattle, Washington, of female health-care workers that exclusively worked night or day shifts. A total of 225 white and 51 Asian participants were included in the analysis. Although 6-sulfatoxymelatonin levels were affected by night shift work in both racial groups, Asian night shift workers consistently showed 6-sulfatoxymelatonin levels that were closer to levels in day shift workers than did white night shift workers. Furthermore, differences in 6-sulfatoxymelatonin levels between white and Asian night shift workers relative to day shift workers were statistically significant in every instance (P < 0.05). These results suggest that Asians may be better able to maintain a “normal” circadian pattern of melatonin production compared with whites and suggest a biological mechanism by which Asian night shift workers may be at a reduced risk of cancer. PMID:23380044

Mechanical energy expenditures and movement efficiency in full body reaching movements.

PubMed

Sha, Daohang; France, Christopher R; Thomas, James S

2010-02-01

The effect of target location, speed, and handedness on the average total mechanical energy and movement efficiency is studied in 15 healthy subjects (7 males and 8 females with age 22.9 +/- 1.79 years old) performing full body reaching movements. The average total mechanical energy is measured as the time average of integration of joint power, potential energy, and kinetic energy respectively. Movement efficiency is calculated as the ratio of total kinetic energy to the total joint power and potential energy. Results show that speed and target location have significant effects on total mechanical energy and movement efficiency, but reaching hand only effects kinetic energy. From our findings we conclude that (1) efficiency in whole body reaching is dependent on whether the height of the body center of mass is raised or lowered during the task; (2) efficiency is increased as movement speed is increased, in part because of greater changes in potential energy; and (3) the CNS does not appear to use movement efficiency as a primary planning variable in full body reaching. It may be dependent on a combination of other factors or constraints.

The effects of different preservation processes on the total protein and growth factor content in a new biological product developed from human amniotic membrane.

PubMed

Russo, Alessandra; Bonci, Paola; Bonci, Paolo

2012-06-01

The aim of this work is to quantify the total protein and growth factors content in a tissue-suspension obtained from processed human amniotic membrane (hAM). hAM was collected, frozen, freeze dried, powdered and sterilized by γ-irradiation. At each step of the process, samples were characterized for the total protein amounts by a Bradford protein assay and for the growth factor concentrations by ELISA test of the tissue suspensions. Frozen-hAM samples show higher release of total proteins and specific growth factors in the tissue suspension in comparison with freeze-dried hAM. We observed that even if the protein extraction is hindered once the tissue is dried, the powdering process allows a greater release in the tissue suspension of total proteins and growth factors after tissue re-solubilization in comparison with only the freeze-drying process (+91 ± 13% for EGF, +16 ± 4% for HGF, +11 ± 5% for FGF, +16 ± 9% for TGF-β1), and a greater release of EGF (85 ± 10%) in comparison with only the freezing process, because proteins become much readily solubilized in the solution. According with these results, we describe a protocol to obtain a new sterile biological product from hAM tissue, with well-known effects of thermal, mechanical and physical processes on the total protein and grow factors contents.

20 CFR 10.400 - What is total disability?

Code of Federal Regulations, 2010 CFR

2010-04-01

..., such as evidence of continued ability to work and to earn wages despite the loss. (b) Temporary total... equivalent wages, or to perform other gainful employment, due to the work-related injury. Except as presumed... pending return to work. ...

20 CFR 10.400 - What is total disability?

Code of Federal Regulations, 2011 CFR

2011-04-01

..., such as evidence of continued ability to work and to earn wages despite the loss. (b) Temporary total... equivalent wages, or to perform other gainful employment, due to the work-related injury. Except as presumed... pending return to work. ...

Evaluation of a bisphosphonate enriched ultra-high molecular weight polyethylene for enhanced total joint replacement bearing surface functionality

NASA Astrophysics Data System (ADS)

Wright-Walker, Cassandra Jane

Each year in the United States there is an increasing trend of patients receiving total joint replacement (TJR) procedures. Approximately a half million total knee replacements (TKRs) are performed annually in the United States with increasing prevalence attributed to baby-boomers, obesity, older, and younger patients. This trend is also seen for total hip replacements (THRs) as well. The use of ultra high molecular weight polyethylene (UHMWPE) inserts in TJRs results in wear particle-induced osteolysis, which is the predominant cause for prosthesis failure and revision surgery. Sub-micron size particle generation is inevitable despite the numerous efforts in improving this bearing material. Work by others has shown that the use of oral and intravenous systemic bisphosphonates (BP) can significantly minimize periprosthetic osteolysis. However, the systemic delivery and the high solubility of BPs results in a predominant portion of the drug being excreted via the kidney without reaching its target, bone. This doctoral research project is focused on the development and evaluation of a novel method to administer BPs locally using the inherent wear of UHMWPE for possible use as an anti-osteolysis treatment. For new materials to be considered, they must be mechanically and tribologically comparable to the current gold standard, UHMWPE. In order to evaluate this material, mechanical, drug elution and tribological experiments were performed to allow assessment of material properties. Tensile tests showed comparable yield stress and pin-on-disk testing showed comparable wear to standard virgin UHMWPE. Further, drug elution tests have shown that BP was released from the enriched material both in static and dynamic conditions. Additionally, an aggressive 2 million cycle total knee simulator experiment has shown statistically similar wear results for the two materials. Overall, this research has provided the groundwork for further characterization and development of a new potential material for total joint replacements as an enhancement to standard UHMWPE. This material shows significant potential as an alternative bearing material to indirectly increase TJR longevity by addressing osteolysis related issues.

Frictional heating processes during laboratory earthquakes

NASA Astrophysics Data System (ADS)

Aubry, J.; Passelegue, F. X.; Deldicque, D.; Lahfid, A.; Girault, F.; Pinquier, Y.; Escartin, J.; Schubnel, A.

2017-12-01

Frictional heating during seismic slip plays a crucial role in the dynamic of earthquakes because it controls fault weakening. This study proposes (i) to image frictional heating combining an in-situ carbon thermometer and Raman microspectrometric mapping, (ii) to combine these observations with fault surface roughness and heat production, (iii) to estimate the mechanical energy dissipated during laboratory earthquakes. Laboratory earthquakes were performed in a triaxial oil loading press, at 45, 90 and 180 MPa of confining pressure by using saw-cut samples of Westerly granite. Initial topography of the fault surface was +/- 30 microns. We use a carbon layer as a local temperature tracer on the fault plane and a type K thermocouple to measure temperature approximately 6mm away from the fault surface. The thermocouple measures the bulk temperature of the fault plane while the in-situ carbon thermometer images the temperature production heterogeneity at the micro-scale. Raman microspectrometry on amorphous carbon patch allowed mapping the temperature heterogeneities on the fault surface after sliding overlaid over a few micrometers to the final fault roughness. The maximum temperature achieved during laboratory earthquakes remains high for all experiments but generally increases with the confining pressure. In addition, the melted surface of fault during seismic slip increases drastically with confining pressure. While melting is systematically observed, the strength drop increases with confining pressure. These results suggest that the dynamic friction coefficient is a function of the area of the fault melted during stick-slip. Using the thermocouple, we inverted the heat dissipated during each event. We show that for rough faults under low confining pressure, less than 20% of the total mechanical work is dissipated into heat. The ratio of frictional heating vs. total mechanical work decreases with cumulated slip (i.e. number of events), and decreases with increasing confining pressure and normal stress. Our results suggest that earthquakes are less dispersive under large normal stress. We linked this observation with fault roughness heterogeneity, which also decreases with applied normal stress. Keywords: Frictional heating, stick-slip, carbon, dynamic rupture, fault weakening.

Work-related back discomfort and associated factors among automotive maintenance mechanics in Eastern Nigeria: A cross sectional study.

PubMed

Abaraogu, Ukachukwu Okoroafor; Ezema, Charles Ikechukwu; Igwe, S E; Egwuonwu, Afamefuna Victor; Okafor, Udoka Chris

2016-02-15

Back pain has been identified as a common cause of disability in the working population. Automotive mechanics habitually use awkward back posture in their course of manual activity and hence may be at risk of work-related back pain. To investigate the prevalence, pattern and severity of back pain among automotive maintenance mechanics, as well as the personal and job variables associated with or predicting occurrence of back pain. Using a cross-sectional design, information about self-reported back pain and the associated variables were collected among 684 randomly recruited automotive mechanics. Prevalence of back pain was 76.02%; with the majority experiencing low back pain. 63.3% of the workers reported they limited their activity due to the back pain. Older workers (>50 years), daily work lasting ≥5 hours duration, no more than primary education, being normal weight, frequent use of kneeling and sustained postures, and lack of knowledge of ergonomic postures were associated with increased prevalence of back pain. Lack of job autonomy, inadequate task clarity, heavy physical work load, manual material handling, strenuous posture, noisy environment, vibrations, work schedule and inadequate auxiliary support were also associated with increased prevalence of back pain among the mechanics. Work-related back pain is prevalent among automotive maintenance mechanics. Work-related back pain is high among automotive maintenance mechanics. Workstation policy and legislation on reduction of risks with combined health literacy and ergonomic education programs in this occupational group are imperative.

Rescue therapy by switching to total face mask after failure of face mask-delivered noninvasive ventilation in do-not-intubate patients in acute respiratory failure.

PubMed

Lemyze, Malcolm; Mallat, Jihad; Nigeon, Olivier; Barrailler, Stéphanie; Pepy, Florent; Gasan, Gaëlle; Vangrunderbeeck, Nicolas; Grosset, Philippe; Tronchon, Laurent; Thevenin, Didier

2013-02-01

To evaluate the impact of switching to total face mask in cases where face mask-delivered noninvasive mechanical ventilation has already failed in do-not-intubate patients in acute respiratory failure. Prospective observational study in an ICU and a respiratory stepdown unit over a 12-month study period. Switching to total face mask, which covers the entire face, when noninvasive mechanical ventilation using facial mask (oronasal mask) failed to reverse acute respiratory failure. Seventy-four patients with a do-not-intubate order and treated by noninvasive mechanical ventilation for acute respiratory failure. Failure of face mask-delivered noninvasive mechanical ventilation was associated with a three-fold increase in in-hospital mortality (36% vs. 10.5%; p = 0.009). Nevertheless, 23 out of 36 patients (64%) in whom face mask-delivered noninvasive mechanical ventilation failed to reverse acute respiratory failure and, therefore, switched to total face mask survived hospital discharge. Reasons for switching from facial mask to total face mask included refractory hypercapnic acute respiratory failure (n = 24, 66.7%), painful skin breakdown or facial mask intolerance (n = 11, 30%), and refractory hypoxemia (n = 1, 2.7%). In the 24 patients switched from facial mask to total face mask because of refractory hypercapnia, encephalopathy score (3 [3-4] vs. 2 [2-3]; p < 0.0001), PaCO2 (87 ± 25 mm Hg vs. 70 ± 17 mm Hg; p < 0.0001), and pH (7.24 ± 0.1 vs. 7.32 ± 0.09; p < 0.0001) significantly improved after 2 hrs of total face mask-delivered noninvasive ventilation. Patients switched early to total face mask (in the first 12 hrs) developed less pressure sores (n = 5, 24% vs. n = 13, 87%; p = 0.0002), despite greater length of noninvasive mechanical ventilation within the first 48 hrs (44 hrs vs. 34 hrs; p = 0.05) and less protective dressings (n = 2, 9.5% vs. n = 8, 53.3%; p = 0.007). The optimal cutoff value for face mask-delivered noninvasive mechanical ventilation duration in predicting facial pressure sores was 11 hrs (area under the receiver operating characteristic curve, 0.86 ± 0.04; 95% confidence interval 0.76-0.93; p < 0.0001; sensitivity, 84%; specificity, 71%). In patients in hypercapnic acute respiratory failure, for whom escalation to intubation is deemed inappropriate, switching to total face mask can be proposed as a last resort therapy when face mask-delivered noninvasive mechanical ventilation has already failed to reverse acute respiratory failure. This strategy is particularly adapted to provide prolonged periods of continuous noninvasive mechanical ventilation while preventing facial pressure sores.

[Barriers and facilitators to health care coordination in two integrated health care organizations in Catalonia (Spain)].

PubMed

Vargas Lorenzo, Ingrid; Vázquez Navarrete, M Luisa

2007-01-01

To analyze 2 integrated delivery systems (IDS) in Catalonia and identify areas for future development to improve their effectiveness. An exploratory, descriptive, qualitative study was carried out based on case studies by means of document analysis and semi-structured individual interviews. A criterion sample of cases and, for each case, of documents and informants was selected. Study cases consisted of the Consorci Sanitari del Maresme (CSdM) and the Consorci Sanitari de Terrassa/Fundació Hospital Sant Llàtzer (FHSLL). A total of 127 documents were analyzed and 29 informants were interviewed: IDS managers (n = 10), technical staff (n = 5), operational unit managers (n = 5) and health professionals (n = 9). Content analysis was conducted, with mixed generation of categories and segmentation by cases and subjects. CSdM and CSdT/FHSLL are health care organizations with backward vertical integration, total services production, and real (CSdM) and virtual (CSdT/FHSLL) ownership. Funds are allocated by care level. The governing body is centralized in CSdM and decentralized in CSdT/FHSLL. In both organizations, the global objectives are oriented toward improving coordination and efficiency but are not in line with those of the operational units. Both organizations present a functional structure with integration of support functions and utilize mechanisms for collaboration between care levels based on work processes standardization. Both IDS present facilitators and barriers to health care coordination. To improve coordination, changes in external elements (payment mechanism) and in internal elements (governing body role, organizational structure and coordination mechanisms) are required.

Unsteady motion, finite Reynolds numbers, and wall effect on Vorticella convallaria contribute contraction force greater than the stokes drag.

PubMed

Ryu, Sangjin; Matsudaira, Paul

2010-06-02

Contraction of Vorticella convallaria, a sessile ciliated protozoan, is completed within a few milliseconds and results in a retraction of its cell body toward the substratum by coiling its stalk. Previous studies have modeled the cell body as a sphere and assumed a drag force that satisfies Stokes' law. However, the contraction-induced flow of the medium is transient and bounded by the substrate, and the maximum Reynolds number is larger than unity. Thus, calculations of contractile force from the drag force are incomplete. In this study, we analyzed fluid flow during contraction by the particle tracking velocimetry and computational fluid dynamics simulations to estimate the contractile force. Particle paths show that the induced flow is limited by the substrate. Simulation-based force estimates suggest that the combined effect of the flow unsteadiness, the finite Reynolds number, and the substrate comprises 35% of the total force. The work done in the early stage of contraction and the maximum power output are similar regardless of the medium viscosity. These results suggest that, during the initial development of force, V. convallaria uses a common mechanism for performing mechanical work irrespective of viscous loading conditions. Copyright (c) 2010 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Effect of Voriconazole on Candida tropicalis Biofilms: Relation with ERG Genes Expression.

PubMed

Fernandes, Tânia; Silva, Sónia; Henriques, Mariana

2016-10-01

Candida tropicalis has emerged as the third most prevalent fungal pathogens and its ability to form biofilms has been considered one of the most important virulence factors, since biofilms represent high tolerance to antifungal agents. However, the mechanisms of C. tropicalis biofilm resistance to antifungals remain poorly understood. Thus, the main aim of this work was to infer about the effect of voriconazole on the formation and control of C. tropicalis biofilms and disclose its relationship with ERG genes' expression. Planktonic cells tolerance of several C. tropicalis clinical isolates to voriconazole was determined through of antifungal susceptibility test, and the effect of this azole against C. tropicalis biofilm formation and pre-formed biofilms was evaluated by cultivable cells determination and total biomass quantification. ERG genes expression was analyzed by quantitative real-time polymerase chain reaction. This work showed that C. tropicalis resistance to voriconazole is strain dependent and that voriconazole was able to partially control biofilm formation, but was unable to eradicate C. tropicalis pre-formed biofilms. Moreover, C. tropicalis biofilms resistance to voriconazole seems to be associated with alterations of sterol content in the cell membrane, resulting in ERG genes overexpression. Voriconazole is unable to control C. tropicalis biofilms, and the overexpression of ERG genes is a possible mechanism of biofilm resistance.

Music therapy for palliative care: A realist review.

PubMed

McConnell, Tracey; Porter, Sam

2017-08-01

Music therapy has experienced a rising demand as an adjunct therapy for symptom management among palliative care patients. We conducted a realist review of the literature to develop a greater understanding of how music therapy might benefit palliative care patients and the contextual mechanisms that promote or inhibit its successful implementation. We searched electronic databases (CINAHL, Embase, Medline, and PsychINFO) for literature containing information on music therapy for palliative care. In keeping with the realist approach, we examined all relevant literature to develop theories that could explain how music therapy works. A total of 51 articles were included in the review. Music therapy was found to have a therapeutic effect on the physical, psychological, emotional, and spiritual suffering of palliative care patients. We also identified program mechanisms that help explain music therapy's therapeutic effects, along with facilitating contexts for implementation. Music therapy may be an effective nonpharmacological approach to managing distressing symptoms in palliative care patients. The findings also suggest that group music therapy may be a cost-efficient and effective way to support staff caring for palliative care patients. We encourage others to continue developing the evidence base in order to expand our understanding of how music therapy works, with the aim of informing and improving the provision of music therapy for palliative care patients.

Skin disease symptoms and related risk factors among young workers in high-risk jobs.

PubMed

Aktas, Emine; Esin, M Nihal

2016-08-01

Occupational skin diseases are the one of the most frequent diseases in many industrialized countries. The studies about skin disease (SD) on young workers were limited. In this study, we aim to evaluate the prevalence of SD symptoms and related risk factors among young workers in high-risk occupations. This cross-sectional study was undertaken between 2011 and 2012 in two vocational training centres. We included 455 young workers who were working as hairdressers, jewellers, or car mechanics. Data were collected with the Nordic Occupational Skin Questionnaire, which was adapted to Turkish for young workers. The average age of the young workers was 17.9 ± 1.7 years. Of the 455 young workers, 52.7% were female and 47.3% were male. During the previous 12 months, the prevalences of the total SD symptoms, hand/forearm eczema symptoms and urticaria symptoms were 49.7%, 44.4%, and 13.4%, respectively. Those who worked as car mechanics were 5.8 times more likely [odds ratio (OR) 5.81, 95%CI: 2.58-13.10) to have a dry skin type, 2.9 times more likely (OR 2.86, 95%CI: 1.72-4.75) to work for >12 h daily, 2.6 times more likely (OR 2.59, 95%CI: 1.25-5.35) to have worked for >5 years, and 3.0 times more likely (OR 3.05, 95%CI: 1.14-8.14) to have SD symptoms. The results indicate that young workers in high-risk jobs have a high frequency of skin symptoms. These results could provide a basis for occupational health professionals to plan prevention programmes for young workers. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

In vivo evaluation of some biophysical parameters of the facial skin of Indian subjects living in Mumbai. Part II: Variability with age and gender.

PubMed

Colomb, L; Flament, F; Wagle, A; Idelcaid, Y; Agrawal, D

2018-04-01

A previously published work explored the diversity of some biophysical parameters (colour, elasticity, sebum production, skin microrelief, etc.) of the skin of 1204 Indian women, differently aged, living in four Indian cities (Chennai, Delhi, Kolkata and Mumbai). The present work aimed at completing such research by focusing on possible gender-related differences in the same skin parameters, between Indian men and women living in the same Indian city (Mumbai). A total of 297 Indian men, differently aged (18-70y), were recruited in Mumbai, completing the panel of 303 women who were previously recruited in this same city. The same instrumental measurements of facial skin colour and its homogeneity, its mechanical properties, the sebum production, skin pores size, skin relief, etc. as in the previous work, were conducted. Overall, the facial skin colour shows a darker complexion in men as compared to women, on forehead, ocular region, lips, chin and cheek. The skin colour unevenness, which increases with age, was found higher in men, as compared to women. At comparable age, women and men present a same density of skin pores, whereas those of men appear larger, up to 55y. The deepness of Crow's feet wrinkles does not significantly differ between genders. A lesser extensibility was found on the cheeks of men. In men, the sebum production was found significantly higher than that of women at ages above 40y. This work indicates some commonly shared age-related skin features between women and men from Mumbai, despite slight different characteristics such as skin pigmentation, forehead/cheek colour contrast, mechanical properties and sebum production. © 2018 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Work stressors, perseverative cognition and objective sleep quality: a longitudinal study among Dutch Helicopter Emergency Medical Service (HEMS) Pilots.

PubMed

Radstaak, Mirjam; Geurts, Sabine A E; Beckers, Debby G J; Brosschot, Jos F; Kompier, Michiel A J

2014-01-01

This longitudinal study examined the associations between work stressors, perseverative cognition and subjective and objective sleep quality. We hypothesized work stressors to be associated with (i) poor nocturnal sleep quality and (ii) higher levels of perseverative cognition during a free evening. We further hypothesized (iii) perseverative cognition to be associated with poor nocturnal sleep quality and (iv) the association between work stressors and sleep quality to be mediated by perseverative cognition. The participants were 24 pilots working for the Dutch Helicopter Emergency Medical Service (HEMS). They completed six questionnaires: at the end of three consecutive day shifts and each morning following the shifts. The questionnaires addressed work stressors (workload, distressing shifts and work-related conflicts), subjective sleep quality and perseverative cognition. Participants wore actigraphs to assess sleep onset latency, total sleep time and number of awakenings. Correlation analysis revealed that (i) distressing shifts were related to delayed sleep onset (r=0.50, p=0.026) and that workload was related to impaired sleep quality (e.g., subjective sleep quality: r=-0.42, p=0.044). Moreover, (ii) distressing shifts were positively related to perseverative cognition (r=0.62, p=0.002), (iii) perseverative cognition delayed sleep onset (r=0.74, p<0.001) and (iv) mediated the association between distressing shifts and sleep onset latency. Perseverative cognition may be an explanatory mechanism in the association between work stressors and poor sleep.

Drift in Neural Population Activity Causes Working Memory to Deteriorate Over Time.

PubMed

Schneegans, Sebastian; Bays, Paul M

2018-05-23

Short-term memories are thought to be maintained in the form of sustained spiking activity in neural populations. Decreases in recall precision observed with increasing number of memorized items can be accounted for by a limit on total spiking activity, resulting in fewer spikes contributing to the representation of each individual item. Longer retention intervals likewise reduce recall precision, but it is unknown what changes in population activity produce this effect. One possibility is that spiking activity becomes attenuated over time, such that the same mechanism accounts for both effects of set size and retention duration. Alternatively, reduced performance may be caused by drift in the encoded value over time, without a decrease in overall spiking activity. Human participants of either sex performed a variable-delay cued recall task with a saccadic response, providing a precise measure of recall latency. Based on a spike integration model of decision making, if the effects of set size and retention duration are both caused by decreased spiking activity, we would predict a fixed relationship between recall precision and response latency across conditions. In contrast, the drift hypothesis predicts no systematic changes in latency with increasing delays. Our results show both an increase in latency with set size, and a decrease in response precision with longer delays within each set size, but no systematic increase in latency for increasing delay durations. These results were quantitatively reproduced by a model based on a limited neural resource in which working memories drift rather than decay with time. SIGNIFICANCE STATEMENT Rapid deterioration over seconds is a defining feature of short-term memory, but what mechanism drives this degradation of internal representations? Here, we extend a successful population coding model of working memory by introducing possible mechanisms of delay effects. We show that a decay in neural signal over time predicts that the time required for memory retrieval will increase with delay, whereas a random drift in the stored value predicts no effect of delay on retrieval time. Testing these predictions in a multi-item memory task with an eye movement response, we identified drift as a key mechanism of memory decline. These results provide evidence for a dynamic spiking basis for working memory, in contrast to recent proposals of activity-silent storage. Copyright © 2018 Schneegans and Bays.

Contribution of psychological, social, and mechanical work exposures to low work ability: a prospective study.

PubMed

Emberland, Jan S; Knardahl, Stein

2015-03-01

To determine the contribution of specific psychological, social, and mechanical work exposures to the self-reported low level of work ability. Employees from 48 organizations were surveyed over a 2-year period (n = 3779). Changes in 16 work exposures and 3 work ability measures-the work ability index score, perceived current, and future work ability-were tested with Spearman rank correlations. Binary logistic regressions were run to determine contribution of work exposures to low work ability. Role conflict, human resource primacy, and positive challenge were the most consistent predictors of low work ability across test designs. Role clarity and fair leadership were less consistent but prominent predictors. Mechanical exposures were not predictive. To protect employee work ability, work place interventions would benefit from focusing on reducing role conflicts and on promoting positive challenges and human resource primacy.

Contribution of Psychological, Social, and Mechanical Work Exposures to Low Work Ability

PubMed Central

Knardahl, Stein

2015-01-01

Objective: To determine the contribution of specific psychological, social, and mechanical work exposures to the self-reported low level of work ability. Methods: Employees from 48 organizations were surveyed over a 2-year period (n = 3779). Changes in 16 work exposures and 3 work ability measures—the work ability index score, perceived current, and future work ability—were tested with Spearman rank correlations. Binary logistic regressions were run to determine contribution of work exposures to low work ability. Results: Role conflict, human resource primacy, and positive challenge were the most consistent predictors of low work ability across test designs. Role clarity and fair leadership were less consistent but prominent predictors. Mechanical exposures were not predictive. Conclusions: To protect employee work ability, work place interventions would benefit from focusing on reducing role conflicts and on promoting positive challenges and human resource primacy. PMID:25470453

Victor Henri: 111 years of his equation.

PubMed

Cornish-Bowden, Athel; Mazat, Jean-Pierre; Nicolas, Serge

2014-12-01

Victor Henri's great contribution to the understanding of enzyme kinetics and mechanism is not always given the credit that it deserves. In addition, his earlier work in experimental psychology is totally unknown to biochemists, and his later work in spectroscopy and photobiology almost equally so. Applying great rigour to his analysis he succeeded in obtaining a model of enzyme action that explained all of the observations available to him, and he showed why the considerable amount of work done in the preceding decade had not led to understanding. His view was that only physical chemistry could explain the behaviour of enzymes, and that models should be judged in accordance with their capacity not only to explain previously known facts but also to predict new observations against which they could be tested. The kinetic equation usually attributed to Michaelis and Menten was in reality due to him. His thesis of 1903 is now available in English. Copyright © 2014 Elsevier B.V. and Société française de biochimie et biologie Moléculaire (SFBBM). All rights reserved.

[Examination of work-related stress and coping strategies among ambulance- and air-ambulance workers].

PubMed

Schiszler, Bence; Karamánné Pakai, Annamária; Szabó, Zoltán; Raposa, László Bence; Pónusz, Róbert; Radnai, Balázs; Endrei, Dóra

2016-11-01

Among Hungary's health sector workers the presence of a high level of stress is known, which can affect the individual. The aim of the authors was to uncover major risk factors causing work-related stress, as well as its extent, and positive and negative coping strategies among ground and aerial rescue workers. From June until October 2015, a national survey was conducted among Hungarian rescue workers. An own questionnaire and Rahe Stress and coping validated short questionnaire online form were used. A total of 141 persons took part in the survey. As compared to air-ambulance workers, ground rescue workers were exposed to higher work-related stress effects (p<0.01), resulting in a much larger variety of physical and psychological symptoms (p<0.05). Based on Global Stress and Coping Index effective coping mechanisms were observed among air rescue workers (p<0.01). It is important to perform regular professional theoretical and practical training. Human resource management should pay attention on occupational stress reduction. Orv. Hetil., 2016, 157(45), 1802-1808.

Development of nanostructures on plasma facing components

NASA Astrophysics Data System (ADS)

Ruzic, David; Fiflis, Peter; Kalathiparambil, Kishor Kumar

2015-11-01

Exposure to low temperature helium plasma, with parameters similar to tokamak edge plasmas, have been found to induce the growth of nanostructures on tungsten. These nanostructures results in an increase in the effective surface area, and will alter the physical properties of the components. Although this has several potential applications in the industrial scenario, it is an undesired effect for fusion reactor components, and is hence necessary to understand their growth mechanisms in order to figure out suitable remedial schemes. Work done using a high density, low temperature helicon discharge plasma source with a resistively heated tungsten wire immersed in the discharge as the substrate have demonstrated the well-defined stages of the growth as a function of total fluence. The required fluence was attained by extending the exposure time. Extensive research work has also shown that a variety of other materials are also prone to develop such structures under similar conditions. In the present work, the effect of the experimental conditions on the various stages of structure development will be presented and a comparison between the structures developed on different types of substrates will be shown.

2 CFR Appendix A to Part 215 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

34 CFR Appendix A to Part 74 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

7 CFR Appendix A to Part 3019 - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

36 CFR Appendix A to Part 1210 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

36 CFR Appendix A to Part 1210 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

34 CFR Appendix A to Part 74 - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

34 CFR Appendix A to Part 74 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

7 CFR Appendix A to Part 3019 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

2 CFR Appendix A to Part 215 - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

7 CFR Appendix A to Part 3019 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

Arch structure is associated with unique joint work, relative joint contributions and stiffness during landing.

PubMed

Powell, Douglas W; Queen, Robin M; Williams, D S Blaise

2016-10-01

To examine lower extremity joint contributions to a landing task in high-(HA) and low-arched (LA) female athletes by quantifying vertical stiffness, joint work and relative joint contributions to landing. Twenty healthy female recreational athletes (10 HA and 10 LA) performed five barefoot drop landings from a height of 30cm. Three-dimensional kinematics (240Hz) and ground reaction forces (960Hz) were recorded simultaneously. Vertical stiffness, joint work values and relative joint work values were calculated using Visual 3D and MatLab. HA athletes had significantly greater vertical stiffness compared to LA athletes (p=0.013). Though no differences in ankle joint work were observed (p=0.252), HA athletes had smaller magnitudes of knee (p=0.046), hip (p=0.019) and total lower extremity joint work values (p=0.016) compared to LA athletes. HA athletes had greater relative contributions of the ankle (p=0.032) and smaller relative contributions of the hip (p=0.049) compared to LA athletes. No differences in relative contributions of the knee were observed (p=0.255). These findings demonstrate that aberrant foot structure is associated with unique contributions of lower extremity joints to load attenuation during landing. These data may provide insight into the unique injury mechanisms associated with arch height in female athletes. Copyright © 2016 Elsevier B.V. All rights reserved.

Immediate total-body CT scanning versus conventional imaging and selective CT scanning in patients with severe trauma (REACT-2): a randomised controlled trial.

PubMed

Sierink, Joanne C; Treskes, Kaij; Edwards, Michael J R; Beuker, Benn J A; den Hartog, Dennis; Hohmann, Joachim; Dijkgraaf, Marcel G W; Luitse, Jan S K; Beenen, Ludo F M; Hollmann, Markus W; Goslings, J Carel

2016-08-13

Published work suggests a survival benefit for patients with trauma who undergo total-body CT scanning during the initial trauma assessment; however, level 1 evidence is absent. We aimed to assess the effect of total-body CT scanning compared with the standard work-up on in-hospital mortality in patients with trauma. We undertook an international, multicentre, randomised controlled trial at four hospitals in the Netherlands and one in Switzerland. Patients aged 18 years or older with trauma with compromised vital parameters, clinical suspicion of life-threatening injuries, or severe injury were randomly assigned (1:1) by ALEA randomisation to immediate total-body CT scanning or to a standard work-up with conventional imaging supplemented with selective CT scanning. Neither doctors nor patients were masked to treatment allocation. The primary endpoint was in-hospital mortality, analysed in the intention-to-treat population and in subgroups of patients with polytrauma and those with traumatic brain injury. The χ(2) test was used to assess differences in mortality. This trial is registered with ClinicalTrials.gov, number NCT01523626. Between April 22, 2011, and Jan 1, 2014, 5475 patients were assessed for eligibility, 1403 of whom were randomly assigned: 702 to immediate total-body CT scanning and 701 to the standard work-up. 541 patients in the immediate total-body CT scanning group and 542 in the standard work-up group were included in the primary analysis. In-hospital mortality did not differ between groups (total-body CT 86 [16%] of 541 vs standard work-up 85 [16%] of 542; p=0.92). In-hospital mortality also did not differ between groups in subgroup analyses in patients with polytrauma (total-body CT 81 [22%] of 362 vs standard work-up 82 [25%] of 331; p=0.46) and traumatic brain injury (68 [38%] of 178 vs 66 [44%] of 151; p=0.31). Three serious adverse events were reported in patients in the total-body CT group (1%), one in the standard work-up group (<1%), and one in a patient who was excluded after random allocation. All five patients died. Diagnosing patients with an immediate total-body CT scan does not reduce in-hospital mortality compared with the standard radiological work-up. Because of the increased radiation dose, future research should focus on the selection of patients who will benefit from immediate total-body CT. ZonMw, the Netherlands Organisation for Health Research and Development. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mechanisms of Pb(II) sorption on a biogenic manganese oxide.

PubMed

Villalobos, Mario; Bargar, John; Sposito, Garrison

2005-01-15

Macroscopic Pb(II) uptake experiments and Pb L3-edge extended X-ray absorption fine structure (EXAFS) spectroscopy were combined to examine the mechanisms of Pb(II) sequestration by a biogenic manganese oxide and its synthetic analogues, all of which are layer-type manganese oxides (phyllomanganates). Relatively fast Pb(II) sorption was observed, as well as extremely high sorption capacities, suggesting Pb incorporation into the structure of the oxides. EXAFS analysis revealed similar uptake mechanisms regardless of the specific nature of the phyllomanganate, electrolyte background, total Pb(II) loading, or equilibration time. One Pb-O and two Pb-Mn shells at distances of 2.30, 3.53, and 3.74 A, respectively, were found, as well as a linear relationship between Brunauer-Emmett-Teller (BET; i.e., external) specific surface area and maximum Pb(II) sorption that also encompassed data from previous work. Both observations support the existence of two bonding mechanisms in Pb(II) sorption: a triple-corner-sharing complex in the interlayers above/ below cationic sheet vacancies (N theoretical = 6), and a double-corner-sharing complex on particle edges at exposed singly coordinated -O(H) bonds (N theoretical = 2). General prevalence of external over internal sorption is predicted, but the two simultaneous sorption mechanisms can account for the widely noted high affinity of manganese oxides for Pb(ll) in natural environments.

Manual calf massage and passive ankle motion reduce the incidence of deep vein thromboembolism after total hip arthroplasty.

PubMed

Imai, Norio; Ito, Tomoyuki; Suda, Ken; Miyasaka, Dai; Endo, Naoto

2017-07-01

Venous thromboembolism is one of the general complications following total hip arthroplasty, wherein various preventive treatments have been recommended. Several studies reported that venous thromboembolism incidence after total hip arthroplasty was similar in patients who were administered prophylaxis with a conventional mechanical procedure alone, and those who were administered pharmacological anticoagulation therapy. Therefore, the optimum methods of prophylaxis are still controversial. The purpose of this study was to investigate whether manual calf massage and passive ankle motion could lower the risk for venous thromboembolism after total hip arthroplasty. We retrospectively reviewed the data of 126 consecutive patients undergoing elective primary unilateral total hip arthroplasty wherein manual calf massage and passive ankle motion were performed after the surgery at our hospitals between January and October 2014. The 138 patients of the control group underwent total hip arthroplasty using the same surgical approach and pre- and postoperative protocols without this mechanical prophylaxis between January and December 2013. This mechanical prophylaxis was performed simultaneously 30 times during approximately 10 s; these procedures were repeated thrice immediately after total hip arthroplasty. Duplex ultrasonography was performed to observe the veins of both legs in all the patients on postoperative day 7. The incidence of deep vein thrombosis was 6.52% and 0.79% in the control and manual calf massage and passive ankle motion groups, respectively. The odds ratio for the manual calf massage and passive ankle motion groups was 8.72. Performing this mechanical prophylaxis reduced the incidence of venous thromboembolism after total hip arthroplasty. This mechanical prophylaxis is not only simple and easy, but is also safe and inexpensive. We therefore recommend that manual calf massage and passive ankle motion be performed in patients who will undergo total hip arthroplasty, if deep vein thrombosis does not exist before the surgery. Copyright © 2017 The Japanese Orthopaedic Association. Published by Elsevier B.V. All rights reserved.

Energetic costs of producing muscle work and force in a cyclical human bouncing task

PubMed Central

Kuo, Arthur D.

2011-01-01

Muscles expend energy to perform active work during locomotion, but they may also expend significant energy to produce force, for example when tendons perform much of the work passively. The relative contributions of work and force to overall energy expenditure are unknown. We therefore measured the mechanics and energetics of a cyclical bouncing task, designed to control for work and force. We hypothesized that near bouncing resonance, little work would be performed actively by muscle, but the cyclical production of force would cost substantial metabolic energy. Human subjects (n = 9) bounced vertically about the ankles at inversely proportional frequencies (1–4 Hz) and amplitudes (15–4 mm), such that the overall rate of work performed on the body remained approximately constant (0.30 ± 0.06 W/kg), but the forces varied considerably. We used parameter identification to estimate series elasticity of the triceps surae tendon, as well as the work performed actively by muscle and passively by tendon. Net metabolic energy expenditure for bouncing at 1 Hz was 1.15 ± 0.31 W/kg, attributable mainly to active muscle work with an efficiency of 24 ± 3%. But at 3 Hz (near resonance), most of the work was performed passively, so that active muscle work could account for only 40% of the net metabolic rate of 0.76 ± 0.28 W/kg. Near resonance, a cost for cyclical force that increased with both amplitude and frequency of force accounted for at least as much of the total energy expenditure as a cost for work. Series elasticity reduces the need for active work, but energy must still be expended for force production. PMID:21212245

Comparison of high‐intensity sound and mechanical vibration for cleaning porous titanium cylinders fabricated using selective laser melting

PubMed Central

Seiffert, Gary; Sutcliffe, Chris

2015-01-01

Abstract Orthopedic components, such as the acetabular cup in total hip joint replacement, can be fabricated using porous metals, such as titanium, and a number of processes, such as selective laser melting. The issue of how to effectively remove loose powder from the pores (residual powder) of such components has not been addressed in the literature. In this work, we investigated the feasibility of two processes, acoustic cleaning using high‐intensity sound inside acoustic horns and mechanical vibration, to remove residual titanium powder from selective laser melting‐fabricated cylinders. With acoustic cleaning, the amount of residual powder removed was not influenced by either the fundamental frequency of the horn used (75 vs. 230 Hz) or, for a given horn, the number of soundings (between 1 and 20). With mechanical vibration, the amount of residual powder removed was not influenced by the application time (10 vs. 20 s). Acoustic cleaning was found to be more reliable and effective in removal of residual powder than cleaning with mechanical vibration. It is concluded that acoustic cleaning using high‐intensity sound has significant potential for use in the final preparation stages of porous metal orthopedic components. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 117–123, 2017. PMID:26426906

CFD analysis of municipal solid waste combustion using detailed chemical kinetic modelling.

PubMed

Frank, Alex; Castaldi, Marco J

2014-08-01

Nitrogen oxides (NO x ) emissions from the combustion of municipal solid waste (MSW) in waste-to-energy (WtE) facilities are receiving renewed attention to reduce their output further. While NO x emissions are currently 60% below allowed limits, further reductions will decrease the air pollution control (APC) system burden and reduce consumption of NH3. This work combines the incorporation of the GRI 3.0 mechanism as a detailed chemical kinetic model (DCKM) into a custom three-dimensional (3D) computational fluid dynamics (CFD) model fully to understand the NO x chemistry in the above-bed burnout zones. Specifically, thermal, prompt and fuel NO formation mechanisms were evaluated for the system and a parametric study was utilized to determine the effect of varying fuel nitrogen conversion intermediates between HCN, NH3 and NO directly. Simulation results indicate that the fuel nitrogen mechanism accounts for 92% of the total NO produced in the system with thermal and prompt mechanisms accounting for the remaining 8%. Results also show a 5% variation in final NO concentration between HCN and NH3 inlet conditions, demonstrating that the fuel nitrogen intermediate assumed is not significant. Furthermore, the conversion ratio of fuel nitrogen to NO was 0.33, revealing that the majority of fuel nitrogen forms N2. © The Author(s) 2014.

Pulmonary blood flow distribution in sheep: effects of anesthesia, mechanical ventilation, and change in posture

NASA Technical Reports Server (NTRS)

Walther, S. M.; Domino, K. B.; Glenny, R. W.; Hlastala, M. P.

1997-01-01

BACKGROUND: Recent studies providing high-resolution images of pulmonary perfusion have questioned the classical zone model of pulmonary perfusion. Hence the present work was undertaken to provide detailed maps of regional pulmonary perfusion to examine the influence of anesthesia, mechanical ventilation, and posture. METHODS: Pulmonary perfusion was analyzed with intravenous fluorescent microspheres (15 microm) in six sheep studied in four conditions: prone and awake, prone with pentobarbital-anesthesia and breathing spontaneously, prone with anesthesia and mechanical ventilation, and supine with anesthesia and mechanical ventilation. Lungs were air dried at total lung capacity and sectioned into approximately 1,100 pieces (about 2 cm3) per animal. The pieces were weighed and assigned spatial coordinates. Fluorescence was read on a spectrophotometer, and signals were corrected for piece weight and normalized to mean flow. Pulmonary blood flow heterogeneity was assessed using the coefficient of variation of flow data. RESULTS: Pentobarbital anesthesia and mechanical ventilation did not influence perfusion heterogeneity, but heterogeneity increased when the animals were in the supine posture (P < 0.01). Gravitational flow gradients were absent in the prone position but present in the supine (P < 0.001 compared with zero). Pulmonary perfusion was distributed with a hilar-to-peripheral gradient in animals breathing spontaneously (P < 0.05). CONCLUSIONS: The influence of pentobarbital anesthesia and mechanical ventilation on pulmonary perfusion heterogeneity is small compared with the effect of changes in posture. Analysis of flow gradients indicate that gravity plays a small role in determining pulmonary blood flow distribution.

Pharyngocutaneous fistula after total laryngectomy: Less common with mechanical stapler closure.

PubMed

Calli, Caglar; Pinar, Ercan; Oncel, Semih

2011-05-01

The aim of the study was to compare the incidences of pharyngocutaneous fistula after total laryngectomy between patients who underwent manual and mechanical suturing for pharyngoesophageal closure. In a retrospective and prospective nonrandomized clinical study conducted at a single tertiary medical center between May 2002 and April 2009, we compared the incidence of pharyngocutaneous salivary fistula between two groups of patients after total laryngectomy. Sixty-one consecutive patients who underwent mechanical suturing with a 60-mm linear stapler (group A) were prospectively enrolled, and 121 patients who had undergone manual suturing (group B) were retrospectively reviewed. The groups were similar in terms of age, gender, comorbidities, TNM (tumor, node, metastasis) stage, and laryngeal tumor extension. The incidence of pharyngocutaneous salivary fistula was 4.9% in group A and 19.8% in group B (p = 0.014). Mechanical stapler closure of the pharynx after total laryngectomy was associated with a significant reduction in the incidence of pharyngocutaneous fistula compared with manual suture in selected cases.

41 CFR Appendix A to Part 105 - 72-Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-07-01

... required to pay wages to laborers and mechanics at a rate not less than the minimum wages specified in a... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

49 CFR Appendix A to Part 19 - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-10-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

41 CFR Appendix A to Part 105 - 72-Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-01-01

... required to pay wages to laborers and mechanics at a rate not less than the minimum wages specified in a... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

10 CFR Appendix A to Subpart B of... - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

10 CFR Appendix A to Subpart B of... - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

41 CFR Appendix A to Part 105 - 72-Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-01-01

... required to pay wages to laborers and mechanics at a rate not less than the minimum wages specified in a... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

49 CFR Appendix A to Part 19 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-10-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

49 CFR Appendix A to Part 19 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-10-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

22 CFR Appendix A to Part 518 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-04-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2,500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

10 CFR Appendix A to Subpart B of... - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-01-01

..., contractors shall be required to pay wages to laborers and mechanics at a rate not less than the minimum wages... construction contracts and in excess of $2500 for other contracts that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work...

Effects of a work injury prevention program for housekeeping in the hotel industry.

PubMed

Landers, Merrill; Maguire, Lynn

2004-01-01

The aim of this retrospective study was to determine the effectiveness of a work injury prevention program in the housekeeping department of a hotel. Studies have validated the use of different injury prevention strategies to decrease the incidence of work-related injuries. Few studies, however, have reported the efficacy of an on-site work injury prevention program by a physical therapist. In 1995, implementation of a work injury prevention program by a physical therapist to 50 housekeeping supervisors, 60 house persons and 340 guest room attendants at a large hotel began. This program included a detailed work risk analysis of the work environment, development of job descriptions, identification of injury-related problematic work situations, and implementation of a job specific supervisor-training program. Supervisor, house person and guest room attendant training was also conducted at the end of 1995 and the beginning of 1997. Data of injury reports in 1995, 1996, and 1997 were analyzed to determine the results of the program. There was a reduction in total injury claims, total medical expenses, total lost work time and total restricted duty time. These results demonstrate the cost effectiveness of implementing a work injury prevention program for housekeeping guest room attendants in the hotel industry. Copyright 2004 IOS Press

A pilot trial comparing the tear-out behavior in screw-sockets and cemented polyethylene acetabular components - a cadaveric study.

PubMed

Möbius, R; Schleifenbaum, S; Grunert, R; Löffler, S; Werner, M; Prietzel, T; Hammer, N

2016-10-01

The removal of well-fixed acetabular components following THA (total hip arthroplasty) is a difficult operation and could be accompanied by the loss of acetabular bone stock. The optimal method for fixation is still under debate. The aim of this pilot study was to compare the tear-out resistance and failure behavior between osseo-integrated and non-integrated screw cups. Furthermore, we examined whether there are differences in the properties mentioned between screw sockets and cemented polyethylene cups. Tear-out resistance and related mechanical work required for the tear-out of osseo-integrated screw sockets are higher than in non-integrated screw sockets. Ten human coxal bones from six cadavers with osseo-integrated screw sockets (n=4), non-integrated (implanted post-mortem, n=3) screw sockets and cemented polyethylene cups (n=3) were used for tear-out testing. The parameters axial failure load and mechanical work for tear-out were introduced as measures for determining the stability of acetabular components following THA. The osseo-integrated screw sockets yielded slightly higher tear-out resistance (1.61±0.26kN) and related mechanical work compared to the non-integrated screw sockets (1.23±0.39kN, P=0.4). The cemented polyethylene cups yielded the lowest tear-out resistance with a failure load of 1.18±0.24kN. Compared to the screw cups implanted while alive, they also differ on a non-significant level (P=0.1). Osseous failure patterns differed especially for the screw sockets compared to the cemented polyethylene cups. Osseo-integration did not greatly influence the tear-out stability in cementless screw sockets following axial loading. Furthermore, the strength of the bone-implant-interface of cementless screw sockets appears to be similar to cemented polyethylene cups. However, given the high failure load, high mechanical load and because of the related bone failure patterns, removal should not be performed by means of tear-out but rather by osteotomes or other curved cutting devices to preserve the acetabular bone stock. Level III, case-control-study. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Worksite adjustments and work ability among employed cancer survivors.

PubMed

Torp, Steffen; Nielsen, Roy A; Gudbergsson, Sævar B; Dahl, Alv A

2012-09-01

This study was conducted to determine how many cancer survivors (CSs) make worksite adjustments and what kinds of adjustments they make. Changes in work ability among employed CSs were explored, and clinical, sociodemographic, and work-related factors associated with the current total work ability were studied. CSs of the ten most common invasive types of cancer for men and women in Norway completed a mailed questionnaire 15-39 months after being diagnosed with cancer. Included in the analyses were all participants who worked both at the time of diagnosis and at the time of the survey and who had not changed their labor force status since diagnosis (n = 563). The current total work ability was compared to the lifetime best (0-10 score). Twenty-six percent of the employed CSs had made adjustments at work, and the most common adjustment was changing the number of work hours per week. Despite the fact that 31% and 23% reported reduced physical and mental work abilities, respectively, more than 90% of the CSs reported that they coped well with their work demands. The mean total work ability score was high (8.6) among both men and women. Being self-employed and working part-time at the time of diagnosis showed significant negative correlations with total work ability, while a favorable psychosocial work environment showed a significant positive correlation. CSs with low work ability were more often in contact with the occupational health service and also made more worksite adjustments than others. The prospects of future work life seem optimistic for Norwegian employed CSs who return to work relatively soon after primary treatment.

Modified sprint interval training protocols: physiological and psychological responses to 4 weeks of training.

PubMed

McKie, Greg L; Islam, Hashim; Townsend, Logan K; Robertson-Wilson, Jennifer; Eys, Mark; Hazell, Tom J

2018-06-01

Sprint interval training (SIT) protocols involving brief (≤15 s) work bouts improve aerobic and anaerobic performance, highlighting peak speed generation as a potentially important adaptive stimulus. To determine the physiological and psychological effects of reducing the SIT work bout duration, while maintaining total exercise and recovery time, 43 healthy males (n = 27) and females (n = 16) trained for 4 weeks (3 times/week) using one of the following running SIT protocols: (i) 30:240 (n = 11; 4-6 × 30-s bouts, 4 min rest); (ii) 15:120 (n = 11; 8-12 × 15-s bouts, 2 min rest); (iii) 5:40 (n = 12; 24-36 × 5-s bouts, 40 s rest); or (iv) served as a nonexercising control (n = 9). Protocols were matched for total work (2-3 min) and rest (16-24 min) durations, as well as the work-to-rest ratio (1:8 s). Pre- and post-training measures included a graded maximal oxygen consumption test, a 5-km time trial, and a 30-s maximal sprint test. Self-efficacy, enjoyment, and intentions were assessed following the last training session. Training improved maximal oxygen consumption (5.5%; P = 0.006) and time-trial performance (5.2%; P = 0.039), with a main effect of time for peak speed (1.7%; P = 0.042), time to peak speed (25%; P < 0.001), and body fat percentage (1.4%; P < 0.001) that appeared to be driven by the training. There were no group effects for self-efficacy (P = 0.926), enjoyment (P = 0.249), or intentions to perform SIT 3 (P = 0.533) or 5 (P = 0.951) times/week. This study effectively demonstrated that the repeated generation of peak speed during brief SIT work bouts sufficiently stimulates adaptive mechanisms promoting increases in aerobic and anaerobic capacity.

State mandatory overtime regulations and newly licensed nurses' mandatory and voluntary overtime and total work hours.

PubMed

Bae, Sung-Heui; Brewer, Carol S; Kovner, Christine T

2012-01-01

Nurse overtime has been used to handle normal variations in patient census and to control chronic understaffing. By 2010, 16 states had regulations to limit nurse overtime. We examined mandatory overtime regulations and their association with mandatory and voluntary overtime and total hours worked by newly licensed registered nurses (NLRNs). For this secondary data analysis, we used a panel survey of NLRNs; the final dataset consisted of 1,706 NLRNs. Nurses working in states that instituted overtime regulations after 2003 or in states that restricted any type of mandatory overtime had a lower probability of experiencing mandatory overtime than those nurses working in states without regulations. Nurses who worked in states with mandatory overtime regulations reported fewer total hours worked per week. The findings of this study provided insight into how mandatory overtime regulations were related to nurse mandatory and voluntary overtime and the total number of hours worked. Future research should investigate institutions' compliance with regulations and the impact of regulations on nurse and patient outcomes. Copyright © 2012 Elsevier Inc. All rights reserved.

Linking Mechanisms of Work-Family Conflict and Segmentation

ERIC Educational Resources Information Center

Michel, Jesse S.; Hargis, Michael B.

2008-01-01

Despite the abundance of work and family research, few studies have compared the linking mechanisms specified in theoretical models of work-family conflict and segmentation. Accordingly, the current study provides a greater degree of empirical clarity concerning the interplay of work and family by directly examining the indirect effects of…

Thermal and mechanical treatments for nickel and some nickel-base alloys: Effects on mechanical properties

NASA Technical Reports Server (NTRS)

Hall, A. M.; Beuhring, V. F.

1972-01-01

This report deals with heat treating and working nickel and nickel-base alloys, and with the effects of these operations on the mechanical properties of the materials. The subjects covered are annealing, solution treating, stress relieving, stress equalizing, age hardening, hot working, cold working, combinations of working and heat treating (often referred to as thermomechanical treating), and properties of the materials at various temperatures. The equipment and procedures used in working the materials are discussed, along with the common problems that may be encountered and the precautions and corrective measures that are available.

Long working hours and overweight and obesity in working adults.

PubMed

Kim, Byung-Mi; Lee, Bo-Eun; Park, Hye-Sook; Kim, Young-Ju; Suh, Young-Ju; Kim, Jeong-Youn; Shin, Ji-Young; Ha, Eun-Hee

2016-01-01

Previous studies have identified a link between gender and the various risk factors associated with obesity. We examined obesity risk factors in working adults to identify the effects of differences in body mass index (BMI) and percentage body fat (PBF) between women and men. A total of 1,120 adults agreed to participate in the study. Data from 711 participants, including 411 women and 300 men, were analyzed. Multiple logistic regression analysis was used to estimate the effects of risk factors on obesity and being overweight. In addition, the least-squares (LS) means of both BMI and PBF were estimated by analysis of covariance (ANCOVA) in a generalized linear model. Increases in BMI and PBF were significantly related to an age > 50 years and long working hours in women after compensating for confounding factors. Using the PBF criterion, the odds ratio (OR) of being overweight or obese in women > 50 years of age who worked for > 9 h a day was 3.9 (95% confidence interval [CI], 1.05-11.00). For BMI, women who were > 50 years of age and worked for > 9 h a day were 3.82 times (95% CI, 1.31-11.14) more likely to be overweight or obese than those who were < 50 years of age and worked for < 9 h a day. Obesity in working adults was associated with > 50 years of age and long working hours in women. Further studies are needed to investigate the underlying mechanisms of this relationship and its potential implications for the prevention and management of excess weight and obesity.

48 CFR 52.222-6 - Construction Wage Rate Requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of a contract. (b)(1) All laborers and mechanics employed or working upon the site of the work will... relationship which may be alleged to exist between the Contractor and such laborers and mechanics. Any wage... mechanics are considered wages paid to such laborers or mechanics, subject to the provisions of paragraph (e...

Double differential cross sections for proton induced electron emission from molecular analogues of DNA constituents for energies in the Bragg peak region

NASA Astrophysics Data System (ADS)

Rudek, Benedikt; Bennett, Daniel; Bug, Marion U.; Wang, Mingjie; Baek, Woon Yong; Buhr, Ticia; Hilgers, Gerhard; Champion, Christophe; Rabus, Hans

2016-09-01

For track structure simulations in the Bragg peak region, measured electron emission cross sections of DNA constituents are required as input for developing parameterized model functions representing the scattering probabilities. In the present work, double differential cross sections were measured for the electron emission from vapor-phase pyrimidine, tetrahydrofuran, and trimethyl phosphate that are structural analogues to the base, the sugar, and the phosphate residue of the DNA, respectively. The range of proton energies was from 75 keV to 135 keV, the angles ranged from 15° to 135°, and the electron energies were measured from 10 eV to 200 eV. Single differential and total electron emission cross sections are derived by integration over angle and electron energy and compared to the semi-empirical Hansen-Kocbach-Stolterfoht (HKS) model and a quantum mechanical calculation employing the first Born approximation with corrected boundary conditions (CB1). The CB1 provides the best prediction of double and single differential cross section, while total cross sections can be fitted with semi-empirical models. The cross sections of the three samples are proportional to their total number of valence electrons.

Case Studies of Rock Bursts Under Complicated Geological Conditions During Multi-seam Mining at a Depth of 800 m

NASA Astrophysics Data System (ADS)

Zhao, Tong-bin; Guo, Wei-yao; Tan, Yun-liang; Yin, Yan-chun; Cai, Lai-sheng; Pan, Jun-feng

2018-05-01

A serious rock burst ("4.19" event) occurred on 19 April 2016 in the No. 4 working face of the No. 10 coal seam in Da'anshan Coal Mine, Jingxi Coalfield. According to the China National Seismological Network, a 2.7 magnitude earthquake was simultaneously recorded in this area. The "4.19" event resulted in damage to the entire longwall face and two gateways that were 105 m in long. In addition, several precursor bursts and mine earthquakes had occurred between October 2014 and April 2016 in the two uphill roadways and the No. 4 working face. In this paper, the engineering geological characteristics and in situ stress field are provided, and then the rock burst distributions are introduced. Next, the temporal and spatial characteristics, geological and mining conditions, and other related essential information are reviewed in detail. The available evidence and possible explanations for the rock burst mechanisms are also presented and discussed. Based on the description and analysis of these bursts, a detailed classification system of rock burst mechanisms is established. According to the main causes and different disturbance stresses (i.e., high/low disturbance stresses and far-field/near-field high disturbance stresses), there are a total of nine types of rock bursts. Thus, some guidelines for controlling or mitigating different types of rock bursts are provided. These experiences and strategies not only provide an essential reference for understanding the different rock burst mechanisms, but also build a critical foundation for selecting mitigation measures and optimizing the related technical parameters during mining or tunnelling under similar conditions.

How Cannabis Causes Paranoia: Using the Intravenous Administration of ∆9-Tetrahydrocannabinol (THC) to Identify Key Cognitive Mechanisms Leading to Paranoia

PubMed Central

Freeman, Daniel; Dunn, Graham; Murray, Robin M.; Evans, Nicole; Lister, Rachel; Antley, Angus; Slater, Mel; Godlewska, Beata; Cornish, Robert; Williams, Jonathan; Di Simplicio, Martina; Igoumenou, Artemis; Brenneisen, Rudolf; Tunbridge, Elizabeth M.; Harrison, Paul J.; Harmer, Catherine J.; Cowen, Philip; Morrison, Paul D.

2015-01-01

Paranoia is receiving increasing attention in its own right, since it is a central experience of psychotic disorders and a marker of the health of a society. Paranoia is associated with use of the most commonly taken illicit drug, cannabis. The objective was to determine whether the principal psychoactive ingredient of cannabis—∆9-tetrahydrocannabinol (THC)—causes paranoia and to use the drug as a probe to identify key cognitive mechanisms underlying paranoia. A randomized, placebo-controlled, between-groups test of the effects of intravenous THC was conducted. A total of 121 individuals with paranoid ideation were randomized to receive placebo, THC, or THC preceded by a cognitive awareness condition. Paranoia was assessed extensively via a real social situation, an immersive virtual reality experiment, and standard self-report and interviewer measures. Putative causal factors were assessed. Principal components analysis was used to create a composite paranoia score and composite causal variables to be tested in a mediation analysis. THC significantly increased paranoia, negative affect (anxiety, worry, depression, negative thoughts about the self), and a range of anomalous experiences, and reduced working memory capacity. The increase in negative affect and in anomalous experiences fully accounted for the increase in paranoia. Working memory changes did not lead to paranoia. Making participants aware of the effects of THC had little impact. In this largest study of intravenous THC, it was definitively demonstrated that the drug triggers paranoid thoughts in vulnerable individuals. The most likely mechanism of action causing paranoia was the generation of negative affect and anomalous experiences. PMID:25031222

The relevance of gene transfer to the safety of food and feed derived from genetically modified (GM) plants.

PubMed

van den Eede, G; Aarts, H; Buhk, H-J; Corthier, G; Flint, H J; Hammes, W; Jacobsen, B; Midtvedt, T; van der Vossen, J; von Wright, A; Wackernagel, W; Wilcks, A

2004-07-01

In 2000, the thematic network ENTRANSFOOD was launched to assess four different topics that are all related to the testing or assessment of food containing or produced from genetically modified organisms (GMOs). Each of the topics was linked to a European Commission (EC)-funded large shared cost action (see http://www.entransfood.com). Since the exchange of genetic information through horizontal (lateral) gene transfer (HGT) might play a more important role, in quantity and quality, than hitherto imagined, a working group dealing with HGT in the context of food and feed safety was established. This working group was linked to the GMOBILITY project (GMOBILITY, 2003) and the results of the deliberations are laid down in this review paper. HGT is reviewed in relation to the potential risks of consuming food or feed derived from transgenic crops. First, the mechanisms for obtaining transgenic crops are described. Next, HGT mechanisms and its possible evolutionary role are described. The use of marker genes is presented in detail as a special case for genes that may pose a risk. Furthermore, the exposure to GMOs and in particular to genetically modified (GM) deoxyribonucleic acid (DNA) is discussed as part of the total risk assessment. The review finishes off with a number of conclusions related to GM food and feed safety. The aim of this paper is to provide a comprehensive overview to assist risk assessors as well as regulators and the general public in understanding the safety issues related to these mechanisms. Copryright 2004 Elsevier Ltd.

The Influence of Altering Push Force Effectiveness on Upper Extremity Demand during Wheelchair Propulsion

PubMed Central

Rankin, Jeffery W.; Kwarciak, Andrew M.; Richter, W. Mark; Neptune, Richard R.

2010-01-01

Manual wheelchair propulsion has been linked to a high incidence of overuse injury and pain in the upper extremity, which may be caused by the high load requirements and low mechanical efficiency of the task. Previous studies have suggested that poor mechanical efficiency may be due to a low effective handrim force (i.e. applied force that is not directed tangential to the handrim). As a result, studies attempting to reduce upper extremity demand have used various measures of force effectiveness (e.g. fraction effective force, FEF) as a guide for modifying propulsion technique, developing rehabilitation programs and configuring wheelchairs. However, the relationship between FEF and upper extremity demand is not well understood. The purpose of this study was to use forward dynamics simulations of wheelchair propulsion to determine the influence of FEF on upper extremity demand by quantifying individual muscle stress, work and handrim force contributions at different values of FEF. Simulations maximizing and minimizing FEF resulted in higher average muscle stresses (23% and 112%) and total muscle work (28% and 71%) compared to a nominal FEF simulation. The maximal FEF simulation also shifted muscle use from muscles crossing the elbow to those at the shoulder (e.g. rotator cuff muscles), placing greater demand on shoulder muscles during propulsion. The optimal FEF value appears to represent a balance between increasing push force effectiveness to increase mechanical efficiency and minimizing upper extremity demand. Thus, care should be taken in using force effectiveness as a metric to reduce upper extremity demand. PMID:20674921

Widening and diversifying the proteome capture by combinatorial peptide ligand libraries via Alcian Blue dye binding.

PubMed

Candiano, Giovanni; Santucci, Laura; Petretto, Andrea; Lavarello, Chiara; Inglese, Elvira; Bruschi, Maurizio; Ghiggeri, Gian Marco; Boschetti, Egisto; Righetti, Pier Giorgio

2015-01-01

Combinatorial peptide ligand libraries (CPLLs) tend to bind complex molecules such as dyes due to their aromatic, heterocyclic, hydrophobic, and ionic nature that may affect the protein capture specificity. In this experimental work Alcian Blue 8GX, a positively charged phthalocyanine dye well-known to bind to glycoproteins and to glucosaminoglycans, was adsorbed on a chemically modified CPLL solid phase, and the behavior of the resulting conjugate was then investigated. The control and dye-adsorbed beads were used to harvest the human urinary proteome at physiological pH, this resulting in a grand total of 1151 gene products identified after the capture. Although the Alcian Blue-modified CPLL incremented the total protein capture by 115 species, it particularly enriched some families among the harvested proteins, such as glycoproteins and nucleotide-binding proteins. This study teaches that it is possible, via the two combined harvest mechanisms, to drive the CPLL capture toward the enrichment of specific protein categories.

Radioactivity of natural medicinal preparations contained extracts from peat mud available in retail trade used externally.

PubMed

Karpińska, Maria; Kapała, Jacek; Raciborska, Agnieszka; Kulesza, Grzegorz; Milewska, Anna; Mnich, Stanisław

2017-08-01

In this work were identified and measured the activity of radioactive isotopes present in medicinal preparations from peat mud and estimated the doses obtained from them during therapy. Radioactivity of 22 preparations from peat mud and 20 water samples from water of the North-East region of Poland was studied. The median of the total activity was 24.8 Bq kg -1 . Total maximal isotope activity was observed in the Iwonicka Cube 146 Bq kg -1 while considerable amounts of isotopes were found in the Kolobrzeska Peat Mud Paste 112 Bq kg -1 . The doses obtained during therapy were within the range of 11 nSv-13 μSv depending on extracts of medicinal preparations from peat mud. The probability that such a small dose would stimulate biological effects is low. However, some clinicians believe that one of the possible therapeutic mechanisms in the treatment of rheumatoid disorders is the induction of immune response by ionising radiation.

A hydrologic retention system and water quality monitoring program for a human decomposition research facility: concept and design.

PubMed

Wozniak, Jeffrey R; Thies, Monte L; Bytheway, Joan A; Lutterschmidt, William I

2015-01-01

Forensic taphonomy is an essential research field; however, the decomposition of human cadavers at forensic science facilities may lead to nutrient loading and the introduction of unique biological compounds to adjacent areas. The infrastructure of a water retention system may provide a mechanism for the biogeochemical processing and retention of nutrients and compounds, ensuring the control of runoff from forensic facilities. This work provides a proof of concept for a hydrologic retention system and an autonomous water quality monitoring program designed to mitigate runoff from The Southeast Texas Applied Forensic Science (STAFS) Facility. Water samples collected along a sample transect were analyzed for total phosphorous, total nitrogen, NO3-, NO2-, NH4, F(-), and Cl(-). Preliminary water quality analyses confirm the overall effectiveness of the water retention system. These results are discussed with relation to how this infrastructure can be expanded upon to monitor additional, more novel, byproducts of forensic science research facilities. © 2014 American Academy of Forensic Sciences.

Increased and mistimed sex hormone production in night shift workers.

PubMed

Papantoniou, Kyriaki; Pozo, Oscar J; Espinosa, Ana; Marcos, Josep; Castaño-Vinyals, Gemma; Basagaña, Xavier; Juanola Pagès, Elena; Mirabent, Joan; Martín, Jordi; Such Faro, Patricia; Gascó Aparici, Amparo; Middleton, Benita; Skene, Debra J; Kogevinas, Manolis

2015-05-01

Night shift work has been associated with an increased risk for breast and prostate cancer. The effect of circadian disruption on sex steroid production is a possible underlying mechanism, underinvestigated in humans. We have assessed daily rhythms of sex hormones and melatonin in night and day shift workers of both sexes. We recruited 75 night and 42 day workers, ages 22 to 64 years, in different working settings. Participants collected urine samples from all voids over 24 hours on a working day. Urinary concentrations of 16 sex steroid hormones and metabolites (estrogens, progestagens, and androgens) and 6-sulfatoxymelatonin were measured in all samples. Mean levels and peak time of total and individual metabolite production were compared between night and day workers. Night workers had higher levels of total progestagens [geometric mean ratio (GMR) 1.65; 95% confidence intervals (CI), 1.17-2.32] and androgens (GMR: 1.44; 95% CI, 1.03-2.00), compared with day workers, after adjusting for potential confounders. The increased sex hormone levels among night shift workers were not related to the observed suppression of 6-sulfatoxymelatonin. Peak time of androgens was significantly later among night workers, compared with day workers (testosterone: 12:14 hours; 10:06-14:48 vs. 08:35 hours; 06:52-10:46). We found increased levels of progestagens and androgens as well as delayed peak androgen production in night shift workers compared with day workers. The increase and mistiming of sex hormone production may explain part of the increased risk for hormone-related cancers observed in night shift workers. ©2015 American Association for Cancer Research.

Compact 2100 nm laser diode module for next-generation DIRCM

NASA Astrophysics Data System (ADS)

Dvinelis, Edgaras; Greibus, Mindaugas; TrinkÅ«nas, Augustinas; NaujokaitÄ--, Greta; Vizbaras, Augustinas; Vizbaras, Dominykas; Vizbaras, Kristijonas

2017-10-01

Compact high-power 2100 nm laser diode module for next-generation directional infrared countermeasure (DIRCM) systems is presented. Next-generation DIRCM systems require compact, light-weight and robust laser modules which could provide intense IR light emission capable of disrupting the tracking sensor of heat-seeking missile. Currently used solid-state and fiber laser solutions for mid-IR band are bulky and heavy making them difficult to implement in smaller form-factor DIRCM systems. Recent development of GaSb laser diode technology greatly improved optical output powers and efficiencies of laser diodes working in 1900 - 2450 nm band [1] while also maintaining very attractive size, weight, power consumption and cost characteristics. 2100 nm laser diode module presented in this work performance is based on high-efficiency broad emitting area GaSb laser diode technology. Each laser diode emitter is able to provide 1 W of CW output optical power with working point efficiency up to 20% at temperature of 20 °C. For output beam collimation custom designed fast-axis collimator and slow-axis collimator lenses were used. These lenses were actively aligned and attached using UV epoxy curing. Total 2 emitters stacked vertically were used in 2100 nm laser diode module. Final optical output power of the module goes up to 2 W at temperature of 20 °C. Total dimensions of the laser diode module are 35 x 25 x 16 mm (L x W x H) with a weight of 28 grams. Finally output beam is bore-sighted to mechanical axes of the module housing allowing for easy integration into next-generation DIRCM systems.

32 CFR Appendix A to Part 34 - Contract Provisions

Code of Federal Regulations, 2014 CFR

2014-07-01

... in excess of $100,000 for construction and other purposes that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work... basic rate of pay for all hours worked in excess of 40 hours in the work week. Section 107 of the Act is...

32 CFR Appendix A to Part 34 - Contract Provisions

Code of Federal Regulations, 2011 CFR

2011-07-01

... in excess of $100,000 for construction and other purposes that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work... basic rate of pay for all hours worked in excess of 40 hours in the work week. Section 107 of the Act is...

32 CFR Appendix A to Part 34 - Contract Provisions

Code of Federal Regulations, 2013 CFR

2013-07-01

... in excess of $100,000 for construction and other purposes that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work... basic rate of pay for all hours worked in excess of 40 hours in the work week. Section 107 of the Act is...

32 CFR Appendix A to Part 34 - Contract Provisions

Code of Federal Regulations, 2012 CFR

2012-07-01

... in excess of $100,000 for construction and other purposes that involve the employment of mechanics or... mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work... basic rate of pay for all hours worked in excess of 40 hours in the work week. Section 107 of the Act is...

Stretching of short monatomic gold chains-some model calculations

NASA Astrophysics Data System (ADS)

Sumali, Priyanka, Verma, Veena; Dharamvir, Keya

2012-06-01

The Mechanical properties of zig-zag monatomic gold chains containing 5 and 7 atoms were studied using the Siesta Code (SC), which works within the framework of DFT formalism and Gupta Potential (GP), which is an effective atom-atom potential. The zig-zag chains were stretched by keeping the end atoms fixed while rest of the atoms were relaxed till minimum energy is obtained. Energy, Force and Young's Modulus found using GP and SC were plotted as functions of total length. It is found that the breaking force in case of GP is of order of 1.6nN while for SIESTA is of the order of 2.9nN for both the chains.

Muon-Induced Neutrons Do Not Explain the DAMA Data

NASA Astrophysics Data System (ADS)

Klinger, J.; Kudryavtsev, V. A.

2015-04-01

We present an accurate model of the muon-induced background in the DAMA/LIBRA experiment. Our work challenges proposed mechanisms which seek to explain the observed DAMA signal modulation with muon-induced backgrounds. Muon generation and transport are performed using the MUSIC /MUSUN code, and subsequent interactions in the vicinity of the DAMA detector cavern are simulated with Geant4. We estimate the total muon-induced neutron flux in the detector cavern to be Φnν=1.0 ×10-9 cm-2 s-1 . We predict 3.49 ×10-5 counts /day /kg /keV , which accounts for less than 0.3% of the DAMA signal modulation amplitude.

Predicting organizational citizenship behavior from the functional analysis and role identity perspectives: further evidence in Spanish employees.

PubMed

Dávila, Ma Celeste; Finkelstein, Marcia A

2010-05-01

Organizational citizenship behavior (OCB) is a prosocial activity with similarities to volunteerism. The purpose of this work is to contribute new evidence about the relevance to OCB of two models of sustained volunteerism, functional analysis and role identity theory. A total of 983 Spanish employees at49 organizations completed surveys measuring amount of OCB, motives for engaging in citizenship behavior, and the degree to which respondents developed an organizational citizen role identity. The results showed that both motives and role identity were significant predictors of OCB, with motive partially mediating the role identity-OCB relationship. The findings suggest that similar mechanisms are involved in sustaining volunteerism and OCB.

Advanced Ignition in Supersonic Airflow by Tunable Plasma System

NASA Astrophysics Data System (ADS)

Firsov, A. A.; Dolgov, E. V.; Leonov, S. B.; Yarantsev, D. A.

2017-10-01

The plasma-based technique was studied for ignition and flameholding in a supersonic airflow in different laboratories for a long time. It was shown that flameholding of gaseous and liquid hydrocarbon fuel is feasible by means of surface DC discharge without employing mechanical flameholders in a supersonic combustion chamber. However, a high power consumption may limit application of this method in a real apparatus. This experimental and computational work explores a distributed plasma system, which allows reducing the total energy consumption and extending the life cycle of the electrode system. Due to the circuit flexibility, this approach may be potentially enriched with feedbacks for design of a close loop control system.

[The possibility of three-dimensional modeling of the mechanisms of damage formation in the framework of situational expertise].

PubMed

Shakir'yanova, Yu P; Leonov, S V; Pinchuk, P V; Sukhareva, M A

This article was designed to share the experience gained with the three-dimensional modeling for the purpose of situational expertise intended to reconstruct the occurrence circumstances and check up the alternative investigative leads concerning formation of potential injuries to a concrete person. Simulation was performed with the use of the dimensionally scaled model of the place of occurrence as well as the models of the human head and body totally consistent with the anthropometric characteristics of the victim. The results of this work made it possible to reject several potential opportunities for the formation of injuries to the victim and identify the most probable version.

Reducing work-related musculoskeletal symptoms through implementation of Kiken Yochi training intervention approach.

PubMed

Ya'acob, Noor Afifah; Abidin, Emilia Zainal; Rasdi, Irniza; Rahman, Anita Abd; Ismail, Suriani

2018-05-01

Work tasks in pineapple plantations in Malaysia are characterised by non-ergonomic work postures, repetitive tasks, awkward posture and manual handling of work tools that contribute to the reporting of musculoskeletal symptoms (MSS). There have been very limited studies performed among pineapple plantation workers focusing on ergonomic intervention programs to specifically reduce MSS. The aim of this study was to assess the effects of work improvement module using a Kiken Yochi participatory approach intervention in reducing MSS among male migrant pineapple farm plantation workers in Pontian, Johor. In this interventional study, a total of 68 male migrant workers from two plantation farms were invited to become a participant in this study. In total, 45 participants that consisted of 27 workers for the intervention group and 18 workers for the control group were recruited. The background of workers and MSS were assessed using questionnaires. Ergonomic and postural risks were evaluated and the work tasks with the highest risk were used as a basis for the development of the Kiken Yochi training module. MSS education and training intervention that provided information on proper lifting techniques and education on body mechanics and ergonomics to reduce MSS were implemented to both groups of workers. Kiken Yochi Training was given to the intervention group only. MSS were reassessed after 2 months of the follow-up period. Data was entered into statistical software and were analysed according to objectives. In terms of the postural risk assessment, almost two-third of the participants (68.5%) had working postures categorized as high risk for MSS. Ergonomic risk assessment identified cultivation, manual weeding and harvesting of pineapples as the work tasks contributing the highest health risks to workers. The most commonly reported MSS between both groups of workers were at the knees, lower back and shoulder area. Upon completion of the delivery of intervention module to both groups of workers, the MSS prevalence reported (after 2 months) were significantly lower for the ankles and feet area within the intervention group. This study suggested that development and implementation of programs using effective participatory approach training methods are able to prevent selected musculoskeletal problems for this occupation. To enhance the effects of such trainings, modifications of work tools in this occupation are desirable.

Efficient preloading of the ventricles by a properly timed atrial contraction underlies stroke work improvement in the acute response to cardiac resynchronization therapy

PubMed Central

Hu, Yuxuan; Gurev, Viatcheslav; Constantino, Jason; Trayanova, Natalia

2013-01-01

Background The acute response to cardiac resynchronization therapy (CRT) has been shown to be due to three mechanisms: resynchronization of ventricular contraction, efficient preloading of the ventricles by a properly timed atrial contraction, and mitral regurgitation reduction. However, the contribution of each of the three mechanisms to the acute response of CRT, specifically stroke work improvement, has not been quantified. Objective The goal of this study was to use an MRI-based anatomically accurate 3D model of failing canine ventricular electromechanics to quantify the contribution of each of the three mechanisms to stroke work improvement and identify the predominant mechanisms. Methods An MRI-based electromechanical model of the failing canine ventricles assembled previously by our group was further developed and modified. Three different protocols were used to dissect the contribution of each of the three mechanisms to stroke work improvement. Results Resynchronization of ventricular contraction did not lead to significant stroke work improvement. Efficient preloading of the ventricles by a properly timed atrial contraction was the predominant mechanism underlying stroke work improvement. Stroke work improvement peaked at an intermediate AV delay, as it allowed ventricular filling by atrial contraction to occur at a low diastolic LV pressure but also provided adequate time for ventricular filling before ventricular contraction. Diminution of mitral regurgitation by CRT led to stroke work worsening instead of improvement. Conclusion Efficient preloading of the ventricles by a properly timed atrial contraction is responsible for significant stroke work improvement in the acute CRT response. PMID:23928177

EFFECTS OF TRITIUM GAS EXPOSURE ON EPDM ELASTOMER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, E.

2009-12-11

Samples of four formulations of ethylene-propylene diene monomer (EPDM) elastomer were exposed to initially pure tritium gas at one atmosphere and ambient temperature for various times up to about 420 days in closed containers. Two formulations were carbon-black-filled commercial formulations, and two were the equivalent formulations without filler synthesized for this work. Tritium effects on the samples were characterized by measuring the sample volume, mass, flexibility, and dynamic mechanical properties and by noting changes in appearance. The glass transition temperature was determined by analysis of the dynamic mechanical properties. The glass transition temperature increased significantly with tritium exposure, and themore » unfilled formulations ceased to behave as elastomers after the longest tritium exposure. The filled formulations were more resistant to tritium exposure. Tritium exposure made all samples significantly stiffer and therefore much less able to form a reliable seal when employed as O-rings. No consistent change of volume or density was observed; there was a systematic lowering of sample mass with tritium exposure. In addition, the significant radiolytic production of gas, mainly protium (H{sub 2}) and HT, by the samples when exposed to tritium was characterized by measuring total pressure in the container at the end of each exposure and by mass spectroscopy of a gas sample at the end of each exposure. The total pressure in the containers more than doubled after {approx}420 days tritium exposure.« less

An energy balance of front crawl.

PubMed

Zamparo, P; Pendergast, D R; Mollendorf, J; Termin, A; Minetti, A E

2005-05-01

With the aim of computing a complete energy balance of front crawl, the energy cost per unit distance (C = Ev(-1), where E is the metabolic power and v is the speed) and the overall efficiency (eta(o) = W(tot)/C, where W(tot) is the mechanical work per unit distance) were calculated for subjects swimming with and without fins. In aquatic locomotion W(tot) is given by the sum of: (1) W(int), the internal work, which was calculated from video analysis, (2) W(d), the work to overcome hydrodynamic resistance, which was calculated from measures of active drag, and (3) W(k), calculated from measures of Froude efficiency (eta(F)). In turn, eta(F) = W(d)/(W(d) + W(k)) and was calculated by modelling the arm movement as that of a paddle wheel. When swimming at speeds from 1.0 to 1.4 m s(-1), eta(F) is about 0.5, power to overcome water resistance (active body drag x v) and power to give water kinetic energy increase from 50 to 100 W, and internal mechanical power from 10 to 30 W. In the same range of speeds E increases from 600 to 1,200 W and C from 600 to 800 J m(-1). The use of fins decreases total mechanical power and C by the same amount (10-15%) so that eta(o) (overall efficiency) is the same when swimming with or without fins [0.20 (0.03)]. The values of eta(o) are higher than previously reported for the front crawl, essentially because of the larger values of W(tot) calculated in this study. This is so because the contribution of W(int) to W(tot )was taken into account, and because eta(F) was computed by also taking into account the contribution of the legs to forward propulsion.

DEMONSTRATION OF A CLOSED LOOP REUSE SYSTEM IN A FIBERGLAS TEXTILE PLANT

EPA Science Inventory

The report describes work done toward providing a totally recycled water system for Owens-Corning's textile fiber manufacturing plant at Anderson, SC. (The work was based on pre-1968 pilot plant work by Owens-Corning that resulted in development of totally recycled industrial was...

Interleukin-6 Level among Shift and Night Workers in Japan: Cross-Sectional Analysis of the J-HOPE Study.

PubMed

Amano, Hoichi; Fukuda, Yoshiharu; Yokoo, Takashi; Yamaoka, Kazue

2018-03-27

Shift workers have a high risk of cardiovascular disease (CVD). Systemic inflammation measured has been associated with the risk of CVD onset, in addition to classical risk factors. However, the association between work schedule and inflammatory cytokine levels remains unclear. The purpose of this study was to examine the association between work schedule and interleukin-6 (IL-6)/high-sensitivity C-reactive protein (hs-CRP) levels among Japanese workers. The present cross-sectional study was a part of the Japanese Study of Health, Occupation and Psychosocial Factors Related Equity (J-HOPE). A total of 5259 persons who measured inflammatory cytokine were analyzed in this study. One-way analysis of variance was used to test log-transformed IL-6/hs-CRP differences by work schedule. Multiple regression analysis was used to examine the difference adjusted for other possible CVD risk factors. There were 3660 participants who had a regular work schedule; the remaining schedules were shift work without night work for 181 participants, shift work with night work for 1276 participants, and only night work for 142 participants. The unadjusted model showed that only night workers were significantly related to high levels of IL-6 compared with regular workers. Even in the multiple regression analysis, the higher level of IL-6 among only night workers remained significant (β=0.058, P=0.01). On the contrary, hs-CRP was not. The present study revealed that only night shift work is significantly associated with high levels of IL-6 in Japanese workers. These observations help us understand the mechanism for the association between work schedule and CVD onset.

Six degree-of-freedom analysis of hip, knee, ankle and foot provides updated understanding of biomechanical work during human walking.

PubMed

Zelik, Karl E; Takahashi, Kota Z; Sawicki, Gregory S

2015-03-01

Measuring biomechanical work performed by humans and other animals is critical for understanding muscle-tendon function, joint-specific contributions and energy-saving mechanisms during locomotion. Inverse dynamics is often employed to estimate joint-level contributions, and deformable body estimates can be used to study work performed by the foot. We recently discovered that these commonly used experimental estimates fail to explain whole-body energy changes observed during human walking. By re-analyzing previously published data, we found that about 25% (8 J) of total positive energy changes of/about the body's center-of-mass and >30% of the energy changes during the Push-off phase of walking were not explained by conventional joint- and segment-level work estimates, exposing a gap in our fundamental understanding of work production during gait. Here, we present a novel Energy-Accounting analysis that integrates various empirical measures of work and energy to elucidate the source of unexplained biomechanical work. We discovered that by extending conventional 3 degree-of-freedom (DOF) inverse dynamics (estimating rotational work about joints) to 6DOF (rotational and translational) analysis of the hip, knee, ankle and foot, we could fully explain the missing positive work. This revealed that Push-off work performed about the hip may be >50% greater than conventionally estimated (9.3 versus 6.0 J, P=0.0002, at 1.4 m s(-1)). Our findings demonstrate that 6DOF analysis (of hip-knee-ankle-foot) better captures energy changes of the body than more conventional 3DOF estimates. These findings refine our fundamental understanding of how work is distributed within the body, which has implications for assistive technology, biomechanical simulations and potentially clinical treatment. © 2015. Published by The Company of Biologists Ltd.

Effect of Cold Rolling on Age Hardening in Excess Mg-Type Al-Mg-Si Alloys Including Some Minor Elements

NASA Astrophysics Data System (ADS)

Ogawa, Yurie; Matsuda, Kenji; Kawabata, Tokimasa; Uetani, Yasuhiro; Ikeno, Susumu

It has been known that transition metals improve the mechanical property of Al-Mg-Si alloy. The thermo-mechanical treatment is also effective to improve the strength of Al-Mg-Si alloy. In this work, the aging behavior of deformed excess Mg-type Al-Mg-Si alloy including Ag,Cu,Pt was investigated by hardness test and TEM observation. The value of the maximum hardness increased and the aging time to the maximum hardness became shorter by increasing the amount of the deformation. The age-hardening ability (ΔHV) was decreased with increasing amount of the deformation. The effect of additional element on AHV was also similar to the result of the deformation described above. Comparing the value of the maximum hardness for the alloys aged at 423-523 K, the ex. Mg-Cu alloy was the highest, the ex. Mg-Ag alloy was middle, and the ex. Mg and ex. Mg-Pt alloys were the lowest because of total amounts of added elements.

Silver nanoparticle aggregation not triggered by an ionic strength mechanism

NASA Astrophysics Data System (ADS)

Botasini, Santiago; Méndez, Eduardo

2013-04-01

The synthesis of stable colloidal solutions of silver nanoparticles is a major goal in the industry to control their fate in aqueous solutions. The present work studies 10-20-nm silver nanoparticle aggregation triggered by the presence of chloride ions. The aggregation process was followed by UV-Vis-NIR spectroscopy and transmission electron microscopy. We found that the mechanism involved differs from the classic explanation of nanoparticle aggregation triggered by an increase in the ionic strength. Moreover, our results give evidence that even when nanoparticles are resistant to an increment of the total amount of ions, the formation of insoluble salts in the vicinity of the nanoparticle is enough to induce the aggregation. The presence of silver chloride around the silver nanoparticles was documented by an X-ray diffraction pattern and electrochemical methods because chloride anions are ubiquitous in real media; this alternative process jeopardized the development of many applications with silver nanoparticles that depend on the use of stable colloids.

Mechanics of tunable helices and geometric frustration in biomimetic seashells

NASA Astrophysics Data System (ADS)

Guo, Qiaohang; Chen, Zi; Li, Wei; Dai, Pinqiang; Ren, Kun; Lin, Junjie; Taber, Larry A.; Chen, Wenzhe

2014-03-01

Helical structures are ubiquitous in nature and engineering, ranging from DNA molecules to plant tendrils, from sea snail shells to nanoribbons. While the helical shapes in natural and engineered systems often exhibit nearly uniform radius and pitch, helical shell structures with changing radius and pitch, such as seashells and some plant tendrils, add to the variety of this family of aesthetic beauty. Here we develop a comprehensive theoretical framework for tunable helical morphologies, and report the first biomimetic seashell-like structure resulting from mechanics of geometric frustration. In previous studies, the total potential energy is everywhere minimized when the system achieves equilibrium. In this work, however, the local energy minimization cannot be realized because of the geometric incompatibility, and hence the whole system deforms into a shape with a global energy minimum whereby the energy in each segment may not necessarily be locally optimized. This novel approach can be applied to develop materials and devices of tunable geometries with a range of applications in nano/biotechnology.

Infrared Spectroscopy of Bilberry Extract Water-in-Oil Emulsions: Sensing the Water-Oil Interface

PubMed Central

Kiefer, Johannes; Frank, Kerstin; Zehentbauer, Florian M.; Schuchmann, Heike P.

2016-01-01

Water-in-oil (w/o) emulsions are of great interest in many areas of the life sciences, including food technology, bioprocess engineering, and pharmaceuticals. Such emulsions are complex multi-component systems and the molecular mechanisms which lead to a stable emulsion are yet to be fully understood. In this work, attenuated total reflection (ATR) infrared (IR) spectroscopy is applied to a series of w/o emulsions of an aqueous anthocyanin-rich bilberry extract dispersed in a medium chain triglyceride (MCT) oil phase. The content of the emulsifier polyglycerin-polyricinoleat (PGPR) has been varied systematically in order to investigate whether or not its concentration has an impact on the molecular stabilization mechanisms. The molecular stabilization is accessed by a careful analysis of the IR spectrum, where changes in the vibrational frequencies and signal strengths indicate alterations of the molecular environment at the water/oil interface. The results suggest that adding emulsifier in excess of 1% by weight does not lead to an enhanced stabilization of the emulsion. PMID:27089376

[The geometry of the keel determines the behaviour of the tibial tray against torsional forces in total knee replacement].

PubMed

García David, S; Cortijo Martínez, J A; Navarro Bermúdez, I; Maculé, F; Hinarejos, P; Puig-Verdié, L; Monllau, J C; Hernández Hermoso, J A

2014-01-01

The keel design of the tibial tray is essential for the transmission of the majority of the forces to the peripheral bone structures, which have better mechanical proprieties, thus reducing the risk of loosening. The aim of the present study was to compare the behaviour of different tibial tray designs submitted to torsional forces. Four different tibial components were modelled. The 3-D reconstruction was made using the Mimics software. The solid elements were generated by SolidWorks. The finite elements study was done by Unigraphics. A torsional force of 6 Nm. applied to the lateral aspects of each tibial tray was simulated. The GENUTECH® tibial tray, with peripheral trabecular bone support, showed a lower displacement and less transmitted tensions under torsional forces. The results suggest that a tibial tray with more peripheral support behaves mechanically better than the other studied designs. Copyright © 2013 SECOT. Published by Elsevier Espana. All rights reserved.

Shock-turbulence interaction in core-collapse supernovae

NASA Astrophysics Data System (ADS)

Abdikamalov, Ernazar; Zhaksylykov, Azamat; Radice, David; Berdibek, Shapagat

2016-10-01

Nuclear shell burning in the final stages of the lives of massive stars is accompanied by strong turbulent convection. The resulting fluctuations aid supernova explosion by amplifying the non-radial flow in the post-shock region. In this work, we investigate the physical mechanism behind this amplification using a linear perturbation theory. We model the shock wave as a one-dimensional planar discontinuity and consider its interaction with vorticity and entropy perturbations in the upstream flow. We find that, as the perturbations cross the shock, their total turbulent kinetic energy is amplified by a factor of ˜2, while the average linear size of turbulent eddies decreases by about the same factor. These values are not sensitive to the parameters of the upstream turbulence and the nuclear dissociation efficiency at the shock. Finally, we discuss the implication of our results for the supernova explosion mechanism. We show that the upstream perturbations can decrease the critical neutrino luminosity for producing explosion by several per cent.

Correlation between electrical, mechanical and chemical properties of fresh and used aircraft engine oils

NASA Astrophysics Data System (ADS)

Gajewski, Juliusz B.; Głogowski, Marek J.; Paszkowski, Maciej; Czarnik-Matusewicz, Bogusława

2011-06-01

In this paper the results are presented of measurements of electrical, mechanical and chemical properties of fresh and used aircraft engine oils. Oils were used in a four-stroke aircraft engine and their samples were taken after the 50-hour work of the engine. The resistivity, permittivity and viscosity of oils were measured as a function of temperature. Additionally, some measurements of the absorbance spectra and size of particles contained in the oils were carried out. The significant reduction in the resistivity of the used Total oil was observed. The relative permittivity of both used oils was slightly increased. The oil's relative viscosity depends on temperature of oil and given time that elapsed from the very first moment when the shear force was applied in a rheometer. The results obtained allowed one to identify more precisely the chemical and physico-chemical interactions occurring in the tested samples, as compared with a typical infrared spectroscopy.

Mechanical properties of steel/kenaf (hybrid) fibers added into concrete mixtures

NASA Astrophysics Data System (ADS)

Baarimah, A. O.; Syed Mohsin, S. M.

2018-04-01

This paper investigates the potential advantages of adding hybrid steel-kenaf fibers to concrete mixtures. Compression and flexural test were conducted on six concrete mixtures at 28 days to investigate the mechanical properties of the concrete. The experimental work consists of six concrete mixtures, in which the first mixture was a control mixture without adding any fiber. The following five concrete mixtures contain a total of 1% of volume fraction for steel, kenaf and a mixture of steel-kenaf (hybrid) fibers. Three ratios were considered for hybrid fibers with the ratios of 0.25/0.75, 0.5/0.5 and 0.75/0.25 for steel and kenaf fibers, respectively. From the investigation, it was observed that fibers have minimal effect on compressive strength of the concrete. However, the findings suggest promising improvement on the flexural strength of the concrete added with hybrid fiber (up to 86%) as well as manages to change the mode of failure of the beam from brittle to a more ductile manner.

ITRAQ-based quantitative proteomic analysis of Cynops orientalis limb regeneration.

PubMed

Tang, Jie; Yu, Yuan; Zheng, Hanxue; Yin, Lu; Sun, Mei; Wang, Wenjun; Cui, Jihong; Liu, Wenguang; Xie, Xin; Chen, Fulin

2017-09-22

Salamanders regenerate their limbs after amputation. However, the molecular mechanism of this unique regeneration remains unclear. In this study, isobaric tags for relative and absolute quantification (iTRAQ) coupled with liquid chromatography tandem mass spectrometry (LC-MS/MS) was employed to quantitatively identify differentially expressed proteins in regenerating limbs 3, 7, 14, 30 and 42 days post amputation (dpa). Of 2636 proteins detected in total, 253 proteins were differentially expressed during different regeneration stages. Among these proteins, Asporin, Cadherin-13, Keratin, Collagen alpha-1(XI) and Titin were down-regulated. CAPG, Coronin-1A, AnnexinA1, Cathepsin B were up-regulated compared with the control. The identified proteins were further analyzed to obtain information about their expression patterns and functions in limb regeneration. Functional analysis indicated that the differentially expressed proteins were associated with wound healing, immune response, cellular process, metabolism and binding. This work indicated that significant proteome alternations occurred during salamander limb regeneration. The results may provide fundamental knowledge to understand the mechanism of limb regeneration.

Molecular spectroscopic study for suggested mechanism of chrome tanned leather.

PubMed

Nashy, Elshahat H A; Osman, Osama; Mahmoud, Abdel Aziz; Ibrahim, Medhat

2012-03-01

Collagen represents the structural protein of the extracellular matrix, which gives strength of hides and/or skin under tanning process. Chrome tan is the most important tanning agent all over the world. The methods for production of leather evolved over several centuries as art and engineering with little understanding of the underlying science. The present work is devoted to suggest the most probable mechanistic action of chrome tan on hide proteins. First the affect of Cr upon hide protein is indicated by the studied mechanical properties. Then the spectroscopic characterization of the hide protein as well as chrome tanned leather was carried out with Horizontal Attenuated Total Reflection (HATR) FT-IR. The obtained results indicate how the chromium can attached with the active sites of collagen. Molecular modeling confirms that chromium can react with amino as well as carboxylate groups. Four schemes were obtained to describe the possible interactions of chrome tan with hide proteins. Copyright © 2011 Elsevier B.V. All rights reserved.

Peace-building and reconciliation dividends of integrated health services delivery in post-conflict Burundi: qualitative assessments of providers and community members.

PubMed

Christensen, Cathryn; Edward, Anbrasi

2015-01-01

While demonstrating causality remains challenging, several 'health-peace' mechanisms have been proposed to describe how health systems contribute to peace-building and stability in post-conflict settings. A qualitative study was undertaken in southern Burundi to identify drivers of social tension and reconciliation in the catchment area of Village Health Works, a health services organisation. Key informant interviews and focus group discussions were conducted in early 2014 with a total of one hundred and twenty community members and staff representing a range of conflict and recovery experience. Themes emerging from these interviews indicated mechanisms at the individual, household, community, and regional levels through which health provision mitigates tensions and promotes social cohesion. This peace dividend was amplified by the clinic's integrated model, which facilitates further community interaction through economic, agricultural and education programmes. Land pressure and the marginalisation of repatriated refugees were cited as drivers of local tension.

Phosphine polymerization by nitric oxide: experimental characterization and theoretical predictions of mechanism.

PubMed

Zhao, Yi-Lei; Flora, Jason W; Thweatt, William David; Garrison, Stephen L; Gonzalez, Carlos; Houk, K N; Marquez, Manuel

2009-02-02

A yellow solid material [P(x)H(y)] has been obtained in the reaction of phosphine (PH(3)) and nitric oxide (NO) at room temperature and characterized by thermogravimetric analysis mass spectrometry (TGA-MS) and attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. In this work using complete basis set (CBS-QB3) methods a plausible mechanism has been investigated for phosphine polymerization in the presence of nitric oxide (NO). Theoretical explorations with the ab initio method suggest (a) instead of the monomer the nitric oxide dimer acts as an initial oxidant, (b) the resulting phosphine oxides (H(3)P=O <--> H(3)P(+)O(-)) in the gas phase draw each other via strong dipolar interactions between the P-O groups, and (c) consequently an autocatalyzed polymerization occurs among the phosphine oxides, forming P-P chemical bonds and losing water. The possible structures of polyhydride phosphorus polymer were discussed. In the calculations a series of cluster models was computed to simulate polymerization.

All-Phononic Digital Transistor on the Basis of Gap-Soliton Dynamics in an Anharmonic Oscillator Ladder.

PubMed

Malishava, Merab; Khomeriki, Ramaz

2015-09-04

A conceptual mechanism of amplification of phonons by phonons on the basis of a nonlinear band-gap transmission (supratransmission) phenomenon is presented. As an example, a system of weakly coupled chains of anharmonic oscillators is considered. One (source) chain is driven harmonically by a boundary with a frequency located in the upper band close to the band edge of the ladder system. Amplification happens when a second (gate) chain is driven by a small signal in the counterphase and with the same frequency as the first chain. If the total driving of both chains overcomes the band-gap transmission threshold, the large amplitude band-gap soliton emerges and the amplification scenario is realized. The mechanism is interpreted as the nonlinear superposition of evanescent and propagating nonlinear modes manifesting in a single or double soliton generation working in band-gap or bandpass regimes, respectively. The results could be straightforwardly generalized for all-optical or all-magnonic contexts and have all the promise of logic gate operations.

Quantum-mechanical predictions of electron-induced ionization cross sections of DNA components

NASA Astrophysics Data System (ADS)

Champion, Christophe

2013-05-01

Ionization of biomolecules remains still today rarely investigated on both the experimental and the theoretical sides. In this context, the present work appears as one of the first quantum mechanical approaches providing a multi-differential description of the electron-induced ionization process of the main DNA components for impact energies ranging from the target ionization threshold up to about 10 keV. The cross section calculations are here performed within the 1st Born approximation framework in which the ejected electron is described by a Coulomb wave whereas the incident and the scattered electrons are both described by a plane wave. The biological targets of interest, namely, the DNA nucleobases and the sugar-phosphate backbone, are here described by means of the GAUSSIAN 09 system using the restricted Hartree-Fock method with geometry optimization. The theoretical predictions also obtained have shown a reasonable agreement with the experimental total ionization cross sections while huge discrepancies have been pointed out with existing theoretical models, mainly developed within a semi-classical framework.

Acculturation and nutritional health of immigrants in Canada: a scoping review.

PubMed

Sanou, Dia; O'Reilly, Erin; Ngnie-Teta, Ismael; Batal, Malek; Mondain, Nathalie; Andrew, Caroline; Newbold, Bruce K; Bourgeault, Ivy L

2014-02-01

Although recent immigrants to Canada are healthier than Canadian born (i.e., the Healthy Immigrant Effect), they experience a deterioration in their health status which is partly due to transitions in dietary habits. Since pathways to these transitions are under-documented, this scoping review aims to identify knowledge gaps and research priorities related to immigrant nutritional health. A total of 49 articles were retrieved and reviewed using electronic databases and a stakeholder consultation was undertaken to consolidate findings. Overall, research tends to confirm the Healthy Immigrant Effect and suggests that significant knowledge gaps in nutritional health persist, thereby creating a barrier to the advancement of health promotion and the achievement of maximum health equity. Five research priorities were identified including (1) risks and benefits associated with traditional/ethnic foods; (2) access and outreach to immigrants; (3) mechanisms and coping strategies for food security; (4) mechanisms of food choice in immigrant families; and (5) health promotion strategies that work for immigrant populations.

Herbicide resistance work in the United States Department of Agriculture-Agricultural Research Service.

PubMed

Vaughn, Kevin C

2003-01-01

Herbicide-resistant weed biotypes are an increasing problem in agriculture, with reports of resistance to almost every herbicide class at some place in the world, and the total number of resistant biotypes at over 250. Agricultural Research Service (ARS) scientists have been key players in this area since the first substantiated occurrence of these resistant biotypes in the 1970s. The most significant of their contributions is the complete unraveling of the mechanism of triazine resistance by Arntzen and colleagues, then with ARS at the University of Illinois. These studies established a high benchmark for research in this area and are a model for all studies in this area. Other ARS scientists have investigated a large number of weed biotypes with resistance to a wide range of herbicide classes and mechanisms of resistance. Collectively, these studies have been used to generate herbicide resistance-management schemes for growers, based upon the herbicide site and the potential for resistance development.

Insight into resolution enhancement in generalized two-dimensional correlation spectroscopy.

PubMed

Ma, Lu; Sikirzhytski, Vitali; Hong, Zhenmin; Lednev, Igor K; Asher, Sanford A

2013-03-01

Generalized two-dimensional correlation spectroscopy (2D-COS) can be used to enhance spectral resolution in order to help differentiate highly overlapped spectral bands. Despite the numerous extensive 2D-COS investigations, the origin of the 2D spectral resolution enhancement mechanism(s) is not completely understood. In the work here, we studied the 2D-COS of simulated spectra in order to develop new insights into the dependence of 2D-COS spectral features on the overlapping band separations, their intensities and bandwidths, and their band intensity change rates. We found that the features in the 2D-COS maps that are derived from overlapping bands were determined by the spectral normalized half-intensities and the total intensity changes of the correlated bands. We identified the conditions required to resolve overlapping bands. In particular, 2D-COS peak resolution requires that the normalized half-intensities of a correlating band have amplitudes between the maxima and minima of the normalized half-intensities of the overlapping bands.

Insight into Resolution Enhancement in Generalized Two-Dimensional Correlation Spectroscopy

PubMed Central

Ma, Lu; Sikirzhytski, Vitali; Hong, Zhenmin; Lednev, Igor K.; Asher, Sanford A.

2014-01-01

Generalized two-dimensional correlation spectroscopy (2D COS) can be used to enhance spectral resolution in order to help differentiate highly overlapped spectral bands. Despite the numerous extensive 2D COS investigations, the origin of the 2D spectral resolution enhancement mechanism(s) are not completely understood. In the work here we studied the 2D COS of simulated spectra in order to develop new insights into the dependence of the 2D COS spectral features on the overlapping band separations, their intensities and bandwidths, and their band intensity change rates. We find that the features in the 2D COS maps that derive from overlapping bands are determined by the spectral normalized half-intensities and the total intensity changes of the correlated bands. We identify the conditions required to resolve overlapping bands. In particular, 2D COS peak resolution requires that the normalized half-intensities of a correlating band have amplitudes between the maxima and minima of the normalized half-intensities of the overlapping bands. PMID:23452492

All-Phononic Digital Transistor on the Basis of Gap-Soliton Dynamics in an Anharmonic Oscillator Ladder

NASA Astrophysics Data System (ADS)

Malishava, Merab; Khomeriki, Ramaz

2015-09-01

A conceptual mechanism of amplification of phonons by phonons on the basis of a nonlinear band-gap transmission (supratransmission) phenomenon is presented. As an example, a system of weakly coupled chains of anharmonic oscillators is considered. One (source) chain is driven harmonically by a boundary with a frequency located in the upper band close to the band edge of the ladder system. Amplification happens when a second (gate) chain is driven by a small signal in the counterphase and with the same frequency as the first chain. If the total driving of both chains overcomes the band-gap transmission threshold, the large amplitude band-gap soliton emerges and the amplification scenario is realized. The mechanism is interpreted as the nonlinear superposition of evanescent and propagating nonlinear modes manifesting in a single or double soliton generation working in band-gap or bandpass regimes, respectively. The results could be straightforwardly generalized for all-optical or all-magnonic contexts and have all the promise of logic gate operations.

Factors influencing intercultural doctor-patient communication: a realist review.

PubMed

Paternotte, Emma; van Dulmen, Sandra; van der Lee, Nadine; Scherpbier, Albert J J A; Scheele, Fedde

2015-04-01

Due to migration, doctors see patients from different ethnic backgrounds. This causes challenges for the communication. To develop training programs for doctors in intercultural communication (ICC), it is important to know which barriers and facilitators determine the quality of ICC. This study aimed to provide an overview of the literature and to explore how ICC works. A systematic search was performed to find literature published before October 2012. The search terms used were cultural, communication, healthcare worker. A realist synthesis allowed us to use an explanatory focus to understand the interplay of communication. In total, 145 articles met the inclusion criteria. We found ICC challenges due to language, cultural and social differences, and doctors' assumptions. The mechanisms were described as factors influencing the process of ICC and divided into objectives, core skills and specific skills. The results were synthesized in a framework for the development of training. The quality of ICC is influenced by the context and by the mechanisms. These mechanisms translate into practical points for training, which seem to have similarities with patient-centered communication. Training for improving ICC can be developed as an extension of the existing training for patient-centered communication. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Emerging memories

NASA Astrophysics Data System (ADS)

Baldi, Livio; Bez, Roberto; Sandhu, Gurtej

2014-12-01

Memory is a key component of any data processing system. Following the classical Turing machine approach, memories hold both the data to be processed and the rules for processing them. In the history of microelectronics, the distinction has been rather between working memory, which is exemplified by DRAM, and storage memory, exemplified by NAND. These two types of memory devices now represent 90% of all memory market and 25% of the total semiconductor market, and have been the technology drivers in the last decades. Even if radically different in characteristics, they are however based on the same storage mechanism: charge storage, and this mechanism seems to be near to reaching its physical limits. The search for new alternative memory approaches, based on more scalable mechanisms, has therefore gained new momentum. The status of incumbent memory technologies and their scaling limitations will be discussed. Emerging memory technologies will be analyzed, starting from the ones that are already present for niche applications, and which are getting new attention, thanks to recent technology breakthroughs. Maturity level, physical limitations and potential for scaling will be compared to existing memories. At the end the possible future composition of memory systems will be discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pyatina, Tatiana; Sugama, Toshifumi; Moon, Juhyuk

An alkali-activated blend of aluminum cement and class F fly ash is an attractive solution for geothermal wells where cement is exposed to significant thermal shocks and aggressive environments. Set-control additives enable the safe cement placement in a well but may compromise its mechanical properties. Here, this work evaluates the effect of a tartaric-acid set retarder on phase composition, microstructure, and strength development of a sodium-metasilicate-activated calcium aluminate/fly ash class F blend after curing at 85 °C, 200 °C or 300 °C. The hardened materials were characterized with X-ray diffraction, thermogravimetric analysis, X-ray computed tomography, and combined scanning electron microscopy/energy-dispersivemore » X-ray spectroscopy and tested for mechanical strength. With increasing temperature, a higher number of phase transitions in non-retarded specimens was found as a result of fast cement hydration. The differences in the phase compositions were also attributed to tartaric acid interactions with metal ions released by the blend in retarded samples. The retarded samples showed higher total porosity but reduced percentage of large pores (above 500 µm) and greater compressive strength after 300 °C curing. Lastly, mechanical properties of the set cements were not compromised by the retarder.« less

Analysis of absorption and reflection mechanisms in a three-dimensional plate silencer

NASA Astrophysics Data System (ADS)

Wang, Chunqi; Huang, Lixi

2008-06-01

When a segment of a rigid duct is replaced by a plate backed by a hard-walled cavity, grazing incident sound waves induce plate vibration, hence sound reflection. Based on this mechanism, a broadband plate silencer, which works effectively from low-to-medium frequencies have been developed recently. A typical plate silencer consists of an expansion chamber with two side-branch cavities covered by light but extremely stiff plates. Such a configuration is two-dimensional in nature. In this paper, numerical study is extended to three-dimensional configurations to investigate the potential improvement in sound reflection. Finite element simulation shows that the three-dimensional configurations perform better than the corresponding two-dimensional design, especially in the relatively high frequency region. Further analysis shows that the three-dimensional design gives better plate response at higher axial modes than the simple two-dimensional design. Sound absorption mechanism is also introduced to the plate silencer by adding two dissipative chambers on the two lateral sides of a two-cavity wave reflector, hence a hybrid silencer. Numerical simulation shows that the proposed hybrid silencer is able to achieve a good moderate bandwidth with much reduced total length in comparison with pure absorption design.

Morton et al. Reply

NASA Technical Reports Server (NTRS)

Morton, Douglas C.; Nagol, Jyoteshwar; Carabajal, Claudia C.; Rosette, Jacqueline; Palace, Michael; Cook, Bruce D.; Vermote, Eric F.; Harding, David J.; North, Peter R. J.

2016-01-01

Multiple mechanisms could lead to up-regulation of dry-season photosynthesis in Amazon forests, including canopy phenology and illumination geometry. We specifically tested two mechanisms for phenology-driven changes in Amazon forests during dry-season months, and the combined evidence from passive optical and lidar satellite data was incompatible with large net changes in canopy leaf area or leaf reflectance suggested by previous studies. We therefore hypothesized that seasonal changes in the fraction of sunlit and shaded canopies, one aspect of bidirectional reflectance effects in Moderate Resolution Imaging Spectroradiometer (MODIS) data, could alter light availability for dry-season photosynthesis and the photosynthetic capacity of Amazon forests without large net changes in canopy composition. Subsequent work supports the hypothesis that seasonal changes in illumination geometry and diffuse light regulate light saturation in Amazon forests. These studies clarify the physical mechanisms that govern light availability in Amazon forests from seasonal variability in direct and diffuse illumination. Previously, in the debate over light limitation of Amazon forest productivity, seasonal changes in the distribution of light within complex Amazon forest canopies were confounded with dry-season increases in total incoming photosynthetically active radiation. In the accompanying Comment, Saleska et al. do not fully account for this confounding effect of forest structure on photosynthetic capacity.

Preoperative predictors of returning to work following primary total knee arthroplasty.

PubMed

Styron, Joseph F; Barsoum, Wael K; Smyth, Kathleen A; Singer, Mendel E

2011-01-05

There is little in the literature to guide clinicians in advising patients regarding their return to work following a primary total knee arthroplasty. In this study, we aimed to identify which factors are important in estimating a patient's time to return to work following primary total knee arthroplasty, how long patients can anticipate being off from work, and the types of jobs to which patients are able to return following primary total knee arthroplasty. A prospective cohort study was performed in which patients scheduled for a primary total knee arthroplasty completed a validated questionnaire preoperatively and at four to six weeks, three months, and six months postoperatively. The questionnaire assessed the patient's occupational physical demands, ability to perform job responsibilities, physical status, and motivation to return to work as well as factors that may impact his or her recovery and other workplace characteristics. Two survival analysis models were constructed to evaluate the time to return to work either at least part-time or full-time. Acceleration factors were calculated to indicate the relative percentage of time until the patient returned to work. The median time to return to work was 8.9 weeks. Patients who reported a sense of urgency about returning to work were found to return in half the time taken by other employees (acceleration factor = 0.468; p < 0.001). Other preoperative factors associated with a faster return to work included being female (acceleration factor = 0.783), self-employment (acceleration factor = 0.792), higher mental health scores (acceleration factor = 0.891), higher physical function scores (acceleration factor = 0.809), higher Functional Comorbidity Index scores (acceleration factor = 0.914), and a handicap accessible workplace (acceleration factor = 0.736). A slower return to work was associated with having less pain preoperatively (acceleration factor = 1.132), having a more physically demanding job (acceleration factor = 1.116), and receiving Workers' Compensation (acceleration factor = 4.360). Although the physical demands of a patient's job have a moderate influence on the patient's ability to return to work following a primary total knee arthroplasty, the patient's characteristics, particularly motivation, play a more important role.

Work hours and sleep/wake behavior of Australian hospital doctors.

PubMed

Ferguson, Sally A; Thomas, Matthew J W; Dorrian, Jillian; Jay, Sarah M; Weissenfeld, Adrian; Dawson, Drew

2010-07-01

The objective of the study was to describe the work and sleep patterns of doctors working in Australian hospitals. Specifically, the aim was to examine the influence of work-related factors, such as hospital type, seniority, and specialty on work hours and their impact on sleep. A total of 635 work periods from 78 doctors were analyzed together with associated sleep history. Work and sleep diary information was validated against an objective measure of sleep/wake activity to provide the first comprehensive database linking work and sleep for individual hospital doctors in Australia. Doctors in large and small facilities had fewer days without work than those doctors working in medium-sized facilities. There were no significant differences in the total hours worked across these three categories of seniority; however, mid-career and senior doctors worked more overnight and weekend on-call periods than junior doctors. With respect to sleep, although higher work hours were related to less sleep, short sleeps (< 5 h in the 24 h prior to starting work) were observed at all levels of prior work history (including no work). In this population of Australian hospital doctors, total hours worked do impact sleep, but the pattern of work, together with other nonwork factors are also important mediators.

Quantum mechanical force field for water with explicit electronic polarization.

PubMed

Han, Jaebeom; Mazack, Michael J M; Zhang, Peng; Truhlar, Donald G; Gao, Jiali

2013-08-07

A quantum mechanical force field (QMFF) for water is described. Unlike traditional approaches that use quantum mechanical results and experimental data to parameterize empirical potential energy functions, the present QMFF uses a quantum mechanical framework to represent intramolecular and intermolecular interactions in an entire condensed-phase system. In particular, the internal energy terms used in molecular mechanics are replaced by a quantum mechanical formalism that naturally includes electronic polarization due to intermolecular interactions and its effects on the force constants of the intramolecular force field. As a quantum mechanical force field, both intermolecular interactions and the Hamiltonian describing the individual molecular fragments can be parameterized to strive for accuracy and computational efficiency. In this work, we introduce a polarizable molecular orbital model Hamiltonian for water and for oxygen- and hydrogen-containing compounds, whereas the electrostatic potential responsible for intermolecular interactions in the liquid and in solution is modeled by a three-point charge representation that realistically reproduces the total molecular dipole moment and the local hybridization contributions. The present QMFF for water, which is called the XP3P (explicit polarization with three-point-charge potential) model, is suitable for modeling both gas-phase clusters and liquid water. The paper demonstrates the performance of the XP3P model for water and proton clusters and the properties of the pure liquid from about 900 × 10(6) self-consistent-field calculations on a periodic system consisting of 267 water molecules. The unusual dipole derivative behavior of water, which is incorrectly modeled in molecular mechanics, is naturally reproduced as a result of an electronic structural treatment of chemical bonding by XP3P. We anticipate that the XP3P model will be useful for studying proton transport in solution and solid phases as well as across biological ion channels through membranes.

Hybrid Vapor Compression Ejector Cycle: Presentation to IAPG Mechanical Working Group

DTIC Science & Technology

2011-08-01

Compression Ejector Cycle: Presentation to IAPG Mechanical Working Group Parmesh Verma and Tom Radcliff, United Technologies Research Center UNCLASSIFIED... Ejector Cycle Presentation to IAPG Mechanical Working Group 5a. CONTRACT NUMBER W909MY-10-C-0005 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...hybrid vapor compression ejector heat pump cycle developed under an American Recovery and Reinvestment Act funded contract is provided. 15. SUBJECT

Revealing the Mystery of the Galilean Principle of Relativity. Part I: Basic Assertions

NASA Astrophysics Data System (ADS)

Yarman, Tolga

2009-08-01

As Galileo has formulated, one cannot detect, once embarked in a uniform translational motion, and not receiving any information from the outside, how fast he is moving. Why? No one that we recall of, has worked out the answer of this question, although the Galilean Principle of Relativity ( GPR), constituted a major ingredient of the Special Theory of Relativity (STR). Thus, consider a quantum mechanical object of “ clock mass” M 0 ( which is just a mass), doing a “ clock motion”, such as rotation, vibration, etc., with a total energy E 0, in a space of size ℛ0. Previously we have established that, if the mass M 0 is multiplied by an arbitrary number γ, then through the relativistic or non-relativistic quantum mechanical description of the object ( which ever is appropriate to describe the case in hand), the size ℛ0 of it, shrinks as much, and the total energy E 0, concomitantly, increases as much. This quantum mechanical occurrence yields, at once, the invariance of the quantity E 0 M 0ℛ{0/2} with regards to the mass change in question, the object being overall at rest; this latter quantity is, on the other hand, as induced by the quantum mechanical framework, necessarily strapped to h 2, the square of the Planck Constant. But this constant is already, dimension wise, Lorentz invariant. Thus, any quantity bearing the dimension of h 2, is Lorentz invariant, too. So is then, the quantity E 0 M 0ℛ{0/2} ( no matter how the size of concern lies with respect to the direction of uniform translational motion) that would come into play. Thence, the quantum mechanical invariance of the quantity E 0 M 0ℛ{0/2} with regards to an arbitrary mass change, comes to be identical to the Lorentz invariance of this quantity, were the object brought to a uniform translational motion. It is this prevalence, which displays, amazingly, the underlying mechanism, securing the end results of the STR, and this via quantum mechanics. The Lorentz invariant quantum mechanical architecture, E 0 M 0ℛ{0/2}˜ h 2, more fundamentally, constitutes the answer of the mystery drawn by the GPR. In this article, we frame the basic assertions, which will be used in a subsequent article, to display the quantum mechanical machinery making the GPR, and to draw the bridge between the GPR and the architecture, we disclose.

[Total artificial heart].

PubMed

Antretter, H; Dumfarth, J; Höfer, D

2015-09-01

To date the CardioWest™ total artificial heart is the only clinically available implantable biventricular mechanical replacement for irreversible cardiac failure. This article presents the indications, contraindications, implantation procedere and postoperative treatment. In addition to a overview of the applications of the total artificial heart this article gives a brief presentation of the two patients treated in our department with the CardioWest™. The clinical course, postoperative rehabilitation, device-related complications and control mechanisms are presented. The total artificial heart is a reliable implant for treating critically ill patients with irreversible cardiogenic shock. A bridge to transplantation is feasible with excellent results.

Population-based incidence and cost of non-fatal injuries in Iran: a consistent under-recognized public health concern.

PubMed

Hafezi-Nejad, Nima; Rahimi-Movaghar, Afarin; Motevalian, Abbas; Amin-Esmaeili, Masoumeh; Sharifi, Vandad; Hajebi, Ahmad; Radgoodarzi, Reza; Hefazi, Mitra; Eslami, Vahid; Karimi, Hasti; Saadat, Soheil; Mohammad, Kazem; Rahimi-Movaghar, Vafa

2015-05-01

To investigate the incidence and determinants of non-fatal injuries, and the cost imposed on victims in an Iranian population aged 15-64 years. Cross-sectional household survey. Three-stage probability sampling was conducted for selection of a representative sample of Iranians. Data on the demographics, history and cost of injury were obtained from face-to-face interviews and telephone calls. In total, 7886 subjects were included in this study. The annual incidence rate of all injuries was 905 (95% confidence interval 853-957) per 1000 population (approximately nine injuries per ten Iranians). The mean (±standard error) incidence rates of first aid injuries (FAIs; medical care not required) and medical-attended injuries (MAIs; medical treatment sought) were 737 ± 24 and 168 ± 12 per 1000 population, respectively. Young, urban females were at highest risk for FAIs, and single males were at highest risk for MAIs. The most common injury description was as follows: non-paid work (activity), home (place), inanimate mechanical force (mechanism), upper limb (site of injury) and open wound (type of injury). For MAIs, the most common place of treatment was hospital. Traffic-related injuries had the highest total cost and the lowest out-of-pocket cost. Total and out-of-pocket costs of non-fatal injuries in Iran in 2011 have been estimated to be US$6,111,138,000 and US$1,480,411,000, respectively. Non-fatal injuries are an under-recognized public health problem. Cost-control policies are essential to reduce the out-of-pocket cost of injuries. Copyright © 2015 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Use of transcriptome sequencing to understand the pistillate flowering in hickory (Carya cathayensis Sarg.).

PubMed

Huang, You-Jun; Liu, Li-Li; Huang, Jian-Qin; Wang, Zheng-Jia; Chen, Fang-Fang; Zhang, Qi-Xiang; Zheng, Bing-Song; Chen, Ming

2013-10-10

Different from herbaceous plants, the woody plants undergo a long-period vegetative stage to achieve floral transition. They then turn into seasonal plants, flowering annually. In this study, a preliminary model of gene regulations for seasonal pistillate flowering in hickory (Carya cathayensis) was proposed. The genome-wide dynamic transcriptome was characterized via the joint-approach of RNA sequencing and microarray analysis. Differential transcript abundance analysis uncovered the dynamic transcript abundance patterns of flowering correlated genes and their major functions based on Gene Ontology (GO) analysis. To explore pistillate flowering mechanism in hickory, a comprehensive flowering gene regulatory network based on Arabidopsis thaliana was constructed by additional literature mining. A total of 114 putative flowering or floral genes including 31 with differential transcript abundance were identified in hickory. The locations, functions and dynamic transcript abundances were analyzed in the gene regulatory networks. A genome-wide co-expression network for the putative flowering or floral genes shows three flowering regulatory modules corresponding to response to light abiotic stimulus, cold stress, and reproductive development process, respectively. Totally 27 potential flowering or floral genes were recruited which are meaningful to understand the hickory specific seasonal flowering mechanism better. Flowering event of pistillate flower bud in hickory is triggered by several pathways synchronously including the photoperiod, autonomous, vernalization, gibberellin, and sucrose pathway. Totally 27 potential flowering or floral genes were recruited from the genome-wide co-expression network function module analysis. Moreover, the analysis provides a potential FLC-like gene based vernalization pathway and an 'AC' model for pistillate flower development in hickory. This work provides an available framework for pistillate flower development in hickory, which is significant for insight into regulation of flowering and floral development of woody plants.

Use of transcriptome sequencing to understand the pistillate flowering in hickory (Carya cathayensis Sarg.)

PubMed Central

2013-01-01

Background Different from herbaceous plants, the woody plants undergo a long-period vegetative stage to achieve floral transition. They then turn into seasonal plants, flowering annually. In this study, a preliminary model of gene regulations for seasonal pistillate flowering in hickory (Carya cathayensis) was proposed. The genome-wide dynamic transcriptome was characterized via the joint-approach of RNA sequencing and microarray analysis. Results Differential transcript abundance analysis uncovered the dynamic transcript abundance patterns of flowering correlated genes and their major functions based on Gene Ontology (GO) analysis. To explore pistillate flowering mechanism in hickory, a comprehensive flowering gene regulatory network based on Arabidopsis thaliana was constructed by additional literature mining. A total of 114 putative flowering or floral genes including 31 with differential transcript abundance were identified in hickory. The locations, functions and dynamic transcript abundances were analyzed in the gene regulatory networks. A genome-wide co-expression network for the putative flowering or floral genes shows three flowering regulatory modules corresponding to response to light abiotic stimulus, cold stress, and reproductive development process, respectively. Totally 27 potential flowering or floral genes were recruited which are meaningful to understand the hickory specific seasonal flowering mechanism better. Conclusions Flowering event of pistillate flower bud in hickory is triggered by several pathways synchronously including the photoperiod, autonomous, vernalization, gibberellin, and sucrose pathway. Totally 27 potential flowering or floral genes were recruited from the genome-wide co-expression network function module analysis. Moreover, the analysis provides a potential FLC-like gene based vernalization pathway and an 'AC’ model for pistillate flower development in hickory. This work provides an available framework for pistillate flower development in hickory, which is significant for insight into regulation of flowering and floral development of woody plants. PMID:24106755

Patterns and Processes in Marine Microeukaryotic Community Biogeography from Xiamen Coastal Waters and Intertidal Sediments, Southeast China

PubMed Central

Chen, Weidong; Pan, Yongbo; Yu, Lingyu; Yang, Jun; Zhang, Wenjing

2017-01-01

Microeukaryotes play key roles in the structure and functioning of marine ecosystems. Little is known about the relative importance of the processes that drive planktonic and benthic microeukaryotic biogeography in subtropical offshore areas. This study compares the microeukaryotic community compositions (MCCs) from offshore waters (n = 12) and intertidal sediments (n = 12) around Xiamen Island, southern China, using high-throughput sequencing of 18S rDNA. This work further quantifies the relative contributions of spatial and environmental variables on the distribution of marine MCCs (including total, dominant, rare and conditionally rare taxa). Our results showed that planktonic and benthic MCCs were significantly different, and the benthic richness (6627 OTUs) was much higher than that for plankton (4044 OTUs) with the same sequencing effort. Further, we found that benthic MCCs exhibited a significant distance-decay relationship, whereas the planktonic communities did not. After removing two unique sites (N2 and N3), however, 72% variation in planktonic community was explained well by stochastic processes. More importantly, both the environmental and spatial factors played significant roles in influencing the biogeography of total and dominant planktonic and benthic microeukaryotic communities, although their relative effects on these community variations were different. However, a high proportion of unexplained variation in the rare taxa (78.1–97.4%) and conditionally rare taxa (49.0–81.0%) indicated that more complex mechanisms may influence the assembly of the rare subcommunity. These results demonstrate that patterns and processes in marine microeukaryotic community assembly differ among the different habitats (coastal water vs. intertidal sediment) and different communities (total, dominant, rare and conditionally rare microeukaryotes), and provide novel insight on the microeukaryotic biogeography and ecological mechanisms in coastal waters and intertidal sediments at local scale. PMID:29075237

Identification and Characterization of New Materials for Construction of Heating Plates for High-Temperature Guarded Hot Plates

NASA Astrophysics Data System (ADS)

Hameury, J.; Koenen, A.; Hay, B.; Wu, J.; Hammerschmidt, U.; Rafeld, E. K.; Pennewitz, E.; Turzó-András, E.; Strnad, R.; Blahut, A.

2018-01-01

The selection of a material for making the hot and cold plates of high-temperature guarded hot plates (HTGHPs) working up to 800°C is still an issue. The material must be machinable, have a high mechanical stability to keep the high level of flatness of the plates and have a high thermal conductivity and a high resistance to oxidation when used in air. Nickel 201 alloy has been used in several instruments, but has shown, sometimes, problems of mechanical stability. The total hemispherical emissivity of the plates must be higher than 0.8 as recommended by the standards. Three ceramic materials, a silicon infiltrated silicon carbide (SiSiC), a machinable aluminum nitride and a sintered aluminum nitride (AlN) with high thermal conductivity claimed at ambient temperature, were selected for tests in thermal conductivity and opacity to thermal radiation. Three paints withstanding high temperatures were tested in total hemispherical emissivity and durability at high temperature. Above 600°C, Nickel 201 alloy has a higher thermal conductivity than the three ceramics. Below 600°C, the SiSiC and the sintered AlN have a thermal conductivity significantly higher than Nickel 201, but the sintered AlN shows a wide transparency spectral band at short wavelengths (below 6.5 μ m). Above 300°C, the three paints have a total hemispherical emissivity above 0.8. One of the paints has polluted the specimens of an insulation material tested in thermal conductivity up to 650°C. The other two can be recommended to coat the hot and cold plates of HTGHPs used up to 800°C.

[Exploring the mechanism of rhizoma coptidis in treating type II diabetes mellitus based on metabolomics by gas chromatography-mass spectrometry].

PubMed

Wang, Jing; Yuan, Zimin; Kong, Hongwei; Li, Yong; Lu, Xin; Xu, Guowang

2012-01-01

Metabolomics was used to explore the mechanism of Rhizoma coptidis in treating type II diabetes mellitus. The rat model of type II diabetes mellitus was constructed by an injection of streptozocin (40 mg/kg), along with diets of fat emulsion. The rats were divided into four groups, the control group, the model group, the Rhizoma coptidis group (10 g/kg) and the metformin group (0.08 g/kg). After the treatment for 30 d, blood samples were collected to test biomedical indexes, and 24 h urine samples were collected for the metabolomics experiment. In the Rhizoma coptidis group, fasting blood glucose (FBG), total cholesterol (TC) and total plasma triglycerides (TG) were significantly decreased by 59.26%, 58.66% and 42.18%, respectively, compared with those in the model group. Based on gas chromatography-mass spectrometry, a urinary metabolomics method was used to study the mechanism of Rhizoma coptidis in treating diabetes mellitus. Based on the principal component analysis, it was found that the model group and control group were separated into two different clusters. The Rhizoma coptidis group was located between the model group and the control group, closer to the control group. Twelve significantly changed metabolites of diabetes mellitus were detected and identified, including 4-methyl phenol, benzoic acid, aminomalonic acid, and so on. After diabetic rats were administered with Rhizoma coptidis, 7 metabolites were significantly changed, and L-ascorbic acid and aminomalonic acid which related with the oxidative stress were significantly regulated to normal. The pharmacological results showed that Rhizoma coptidis could display anti-hyperglycemic and anti-hyperlipidemic effects. The Rhizoma coptidis had antioxidation function in preventing the occurrence of complications with diabetes mellitus to some extent. The work illustrates that the metabolomics method is a useful tool to study the treatment mechanism of traditional Chinese medicine.

A Novel Method to Assess Wear Rates of Retrieved Tibial Inserts Following in-vivo Use

NASA Astrophysics Data System (ADS)

Paniogue, Tanille J.

Ultra-high molecular weight polyethylene (UHMWPE) on cobalt chrome is the bearing couple of choice for total knee arthroplasty. The number of patients undergoing total knee arthroplasty has been steadily growing and is projected to continue increasing rapidly in the near future. Many of these patients are younger and more active and therefore need a longer lasting device. However, many of these devices fail prematurely and often the primary reason for failure and ultimately revision is due to wear related issues. Therefore, examining how wear rates of the UHMWPE tibial insert change during in-vivo use can help elucidate the mechanisms of accelerated wear and hopefully aid in finding solutions to combat wear related failures. Different crosslinking treatments have been employed by manufacturers to improve wear resistance of the polyethylene. While this has been shown to be an effective way to reduce wear, crosslinking has led to other issues such as oxidative instability and a decline in mechanical properties. The purpose of this body of work is to examine how changes in oxidation, after in-vivo use, affect wear resistance. A novel testing method was developed to test the native articular surface from retrieved tibial inserts in a laboratory Pin-on-Disk (POD) simulator. The method was validated using short-duration implant articular surfaces and non-articular control pins. In the absence of high surface oxidation or severe surface damage, the articular surface pins had comparable steady state wear rates to their bulk counterparts. Tests of devices with longer in-vivo service show chemical changes consistent with a free-radical mediated oxidation mechanism. Tribological assessment of the articular surfaces shows increasing wear rates as a function of oxidation. While this relationship has been hypothesized in the literature, these experiments represent the first physical demonstration of the phenomenon. The wear mechanism is further explored through infrared spectroscopy, assessment of the wear scar, and documentation of evolution of the contact surfaces in the articulation.

Ibuprofen Differentially Affects Supraspinatus Muscle and Tendon Adaptations to Exercise in a Rat Model.

PubMed

Rooney, Sarah Ilkhanipour; Baskin, Rachel; Torino, Daniel J; Vafa, Rameen P; Khandekar, Pooja S; Kuntz, Andrew F; Soslowsky, Louis J

2016-09-01

Previous studies have shown that ibuprofen is detrimental to tissue healing after acute injury; however, the effects of ibuprofen when combined with noninjurious exercise are debated. Administration of ibuprofen to rats undergoing a noninjurious treadmill exercise protocol will abolish the beneficial adaptations found with exercise but will have no effect on sedentary muscle and tendon properties. Controlled laboratory study. A total of 167 male Sprague-Dawley rats were divided into exercise or cage activity (sedentary) groups and acute (a single bout of exercise followed by 24 hours of rest) and chronic (2 or 8 weeks of repeated exercise) response times. Half of the rats were administered ibuprofen to investigate the effects of this drug over time when combined with different activity levels (exercise and sedentary). Supraspinatus tendons were used for mechanical testing and histologic assessment (organization, cell shape, cellularity), and supraspinatus muscles were used for morphologic (fiber cross-sectional area, centrally nucleated fibers) and fiber type analysis. Chronic intake of ibuprofen did not impair supraspinatus tendon organization or mechanical adaptations (stiffness, modulus, maximum load, maximum stress, dynamic modulus, or viscoelastic properties) to exercise. Tendon mechanical properties were not diminished and in some instances increased with ibuprofen. In contrast, total supraspinatus muscle fiber cross-sectional area decreased with ibuprofen at chronic response times, and some fiber type-specific changes were detected. Chronic administration of ibuprofen does not impair supraspinatus tendon mechanical properties in a rat model of exercise but does decrease supraspinatus muscle fiber cross-sectional area. This fundamental study adds to the growing literature on the effects of ibuprofen on musculoskeletal tissues and provides a solid foundation on which future work can build. The study findings suggest that ibuprofen does not detrimentally affect regulation of supraspinatus tendon adaptations to exercise but does decrease muscle growth. Individuals should be advised on the risk of decreased muscle hypertrophy when consuming ibuprofen. © 2016 The Author(s).

Relational regulation theory and the role of social support and organisational fairness for nurses in a general acute context.

PubMed

Rodwell, John; Munro, Louise

2013-11-01

To present a novel approach to nurse stress by exploring the demand-control-support model with organisational justice through the lens of relational regulation theory. Nursing is often stressful due to high demands and dissatisfaction with pay, which impacts the mental well-being and productivity of nurses. A cross-sectional design. A validated questionnaire was sent to the work addresses of all nursing and midwifery staff in a medium-sized general acute hospital in Australia. A total of 190 nurses and midwives returned completed questionnaires for the analyses. The multiple regression analyses demonstrated that the model applies to the prototypical context of a general acute hospital and that job control, supervisor support and outside work support improve the job satisfaction and mental health of nurses. Most importantly, supervisor support was found to buffer the impact of excessive work demands. Fairness of procedures, distribution of resources and the quality and consistency of information are also beneficial. Relational regulation theory is applied to these findings as a novel way to conceptualise the mechanisms of support and fairness in nursing. The importance of nurses' well-being and job satisfaction is a priority for improving clinical outcomes. Practically, this means nurse managers should be encouraging nurses in the pursuit of diverse relational activities both at work and outside work. © 2013 John Wiley & Sons Ltd.

Effects of front-loading and stagger angle on endwall losses of high lift low pressure turbine vanes

NASA Astrophysics Data System (ADS)

Lyall, M. Eric

Past efforts to reduce the airfoil count in low pressure turbines have produced high lift profiles with unacceptably high endwall loss. The purpose of the current work is to suggest alternative approaches for reducing endwall losses. The effects of the fluid mechanics and high lift profile geometry are considered. Mixing effects of the mean flow and turbulence fields are decoupled to show that mean flow shear in the endwall wake is negligible compared to turbulent shear, indicating that turbulence dissipation is the primary cause of total pressure loss. The mean endwall flow field does influence total pressure loss by causing excessive wake growth and perhaps outright separation on the suction surface. For equivalent stagger angles, a front-loaded high lift profile will produce less endwall loss than one aft-loaded, primarily by suppressing suction surface flow separation. Increasing the stagger setting, however, increases the endwall loss due to the static pressure field generating a stronger blockage relative to the incoming endwall boundary layer flow and causing a larger mass of fluid to become entrained in the horseshoe vortex. In short, front-loading the pressure distribution suppresses suction surface separation whereas limiting the stagger angle suppresses inlet boundary layer separation. Results of this work suggest that a front-loaded low stagger profile be used at the endwall to reduce the endwall loss.

Overcoming the drawback of lower sense margin in tunnel FET based dynamic memory along with enhanced charge retention and scalability

NASA Astrophysics Data System (ADS)

Navlakha, Nupur; Kranti, Abhinav

2017-11-01

The work reports on the use of a planar tri-gate tunnel field effect transistor (TFET) to operate as dynamic memory at 85 °C with an enhanced sense margin (SM). Two symmetric gates (G1) aligned to the source at a partial region of intrinsic film result into better electrostatic control that regulates the read mechanism based on band-to-band tunneling, while the other gate (G2), positioned adjacent to the first front gate is responsible for charge storage and sustenance. The proposed architecture results in an enhanced SM of ˜1.2 μA μm-1 along with a longer retention time (RT) of ˜1.8 s at 85 °C, for a total length of 600 nm. The double gate architecture towards the source increases the tunneling current and also reduces short channel effects, enhancing SM and scalability, thereby overcoming the critical bottleneck faced by TFET based dynamic memories. The work also discusses the impact of overlap/underlap and interface charges on the performance of TFET based dynamic memory. Insights into device operation demonstrate that the choice of appropriate architecture and biases not only limit the trade-off between SM and RT, but also result in improved scalability with drain voltage and total length being scaled down to 0.8 V and 115 nm, respectively.

Boundary conditions for a one-sided numerical model of evaporative instabilities in sessile drops of ethanol on heated substrates

NASA Astrophysics Data System (ADS)

Semenov, Sergey; Carle, Florian; Medale, Marc; Brutin, David

2017-12-01

The work is focused on obtaining boundary conditions for a one-sided numerical model of thermoconvective instabilities in evaporating pinned sessile droplets of ethanol on heated substrates. In the one-sided model, appropriate boundary conditions for heat and mass transfer equations are required at the droplet surface. Such boundary conditions are obtained in the present work based on a derived semiempirical theoretical formula for the total droplet's evaporation rate, and on a two-parametric nonisothermal approximation of the local evaporation flux. The main purpose of these boundary conditions is to be applied in future three-dimensional (3D) one-sided numerical models in order to save a lot of computational time and resources by solving equations only in the droplet domain. Two parameters, needed for the nonisothermal approximation of the local evaporation flux, are obtained by fitting computational results of a 2D two-sided numerical model. Such model is validated here against parabolic flight experiments and the theoretical value of the total evaporation rate. This study combines theoretical, experimental, and computational approaches in convective evaporation of sessile droplets. The influence of the gravity level on evaporation rate and contributions of different mechanisms of vapor transport (diffusion, Stefan flow, natural convection) are shown. The qualitative difference (in terms of developing thermoconvective instabilities) between steady-state and unsteady numerical approaches is demonstrated.

Evaluating degradation of silk's fibroin by attenuated total reflectance infrared spectroscopy: Case study of ancient banners from Polish collections

NASA Astrophysics Data System (ADS)

Koperska, M. A.; Łojewski, T.; Łojewska, J.

2015-01-01

In this study a part of research where artificially aged model samples were used as a guideline to the mechanism of degradation is presented. In previous work Bombyx Mori silk samples were exposed to various environments such as different oxygen, water vapour and volatile organic products content, all at the temperature of 150 °C [11]. Based on those results gathered with by Attenuated Total Reflectance/Fourier Transform Infrared Spectroscopy (ATR-FTIR) the degradation estimators were proposed and classified as follows: Primary functional groups estimators EAmideI/II - intensity ratios of Amide I Cdbnd O stretching vibration to Amide II Nsbnd H in-plane bending and Csbnd N stretching vibrations A1620/A1514. ECOOH - band 1318 cm-1 integral to band integral of CH3 bending vibration band located at 1442 cm-1P1318/P1442. Secondary conformational estimators EcCdbndO2 - intensity ratios within Amide I Cdbnd O stretching vibration of parallel β-sheet to antiparallel β-sheet A1620/A1699. In this work estimators were verified against estimators calculated from spectra of silk samples from 8 museum objects: 3 from 19th, 2 from 18th, 1 from 17th and 2 from 16th century including 3 banners from the storage resources of the Wawel Royal Castle in Cracow, Poland.

Influence of Temperature and Grain Size on Austenite Stability in Medium Manganese Steels

NASA Astrophysics Data System (ADS)

Zhang, Yulong; Wang, Li; Findley, Kip O.; Speer, John G.

2017-05-01

With an aim to elucidate the influence of temperature and grain size on austenite stability, a commercial cold-rolled 7Mn steel was annealed at 893 K (620 °C) for times varying between 3 minutes and 96 hours to develop different grain sizes. The austenite fraction after 3 minutes was 34.7 vol pct, and at longer times was around 40 pct. An elongated microstructure was retained after shorter annealing times while other conditions exhibited equiaxed ferrite and austenite grains. All conditions exhibit similar temperature dependence of mechanical properties. With increasing test temperature, the yield and tensile strength decrease gradually, while the uniform and total elongation increase, followed by an abrupt drop in strength and ductility at 393 K (120 °C). The Olson-Cohen model was applied to fit the transformed austenite fractions for strained tensile samples, measured by means of XRD. The fit results indicate that the parameters α and β decrease with increasing test temperature, consistent with increased austenite stability. The 7Mn steels exhibit a distinct temperature dependence of the work hardening rate. Optimized austenite stability provides continuous work hardening in the temperature range of 298 K to 353 K (25 °C to 80 °C). The yield and tensile strengths have a strong dependence on grain size, although grain size variations have less effect on uniform and total elongation.

Paid and unpaid working hours among Swedish men and women in relation to depressive symptom trajectories: results from four waves of the Swedish Longitudinal Occupational Survey of Health.

PubMed

Peristera, Paraskevi; Westerlund, Hugo; Magnusson Hanson, Linda L

2018-06-07

Long working hours and unpaid work are possible risk factors for depressive symptoms. However, little is known about how working hours influence the course of depressive symptoms. This study examined the influence of paid, unpaid working hours and total working hours on depressive symptoms trajectories. The study was based on data from four waves of the Swedish Longitudinal Occupational Survey of Health (SLOSH 2008-2014). We applied group-based trajectory modelling in order to identify trajectories of depressive symptoms and studied paid and unpaid working hours and total working hours as risk factors. Six trajectory groups were identified with symptoms: 'very low stable', 'low stable', 'doubtful increasing', 'high decreasing', 'mild decreasing' and 'high stable'. More time spent on unpaid work was associated with the 'low stable' (OR 1.16, 95% CI 1.04 to 1.30) and the 'high stable (OR 1.40, 95% CI 1.18 to 1.65) symptom trajectories compared with being in the 'very low stable' symptom group. In addition, more total working hours was associated with a higher probability of having 'high decreasing' (OR 1.30, 95% CI 1.14 to 1.48) and 'high stable' (OR 1.22, 95% CI 1.01 to 1.47) symptoms, when adjusting for sex, age, civil status and socioeconomic status. The results, however, differed somewhat for men and women. More unpaid working hours was more clearly associated with higher symptom trajectories among women. More total working hours was associated with 'high stable' symptoms among women only. This study supported heterogeneous individual patterns of depressive symptoms over time among the Swedish working population. The results also indicate that a higher burden of unpaid work and longer total working hours, which indicate a double burden from paid and unpaid work, may be associated with higher depressive symptom trajectories, especially among women. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Absence from work due to occupational and non-occupational accidents.

PubMed

Jørgensen, Kirsten; Laursen, Bjarne

2013-02-01

The aim of the present study was to investigate absence from work in Denmark due to occupational and non-occupational accidents. Since the beginning of the last decade, political focus has been placed on the population's working capacity and the scope of absence due to illness. Absence from work is estimated at between 3% and 6% of working hours in the EU and costs are estimated at approximately 2.5% of GNP. Victims of accidents treated at two emergency departments were interviewed regarding absence for the injured, the family and others. All answers were linked to the hospital information on the injury, so that it was possible to examine the relation between absence and injury type, and cause of the accident. In total, 1,479 injured persons were interviewed. 36% of these reported absence from work by themselves or others. In mean, an injury caused 3.21 days of absence. Based on this the total absence due to injuries in Denmark was estimated to 1,822,000 workdays, corresponding to approximately 6% of the total absence from work due to all types of illness. Non-occupational injuries resulted in more absence than did occupational injuries. Absence due to accidents contributed to a considerable part of the total absence from work, and non-occupational accidents caused more absence than did occupational accidents.

Recovery after shift work: Relation to coronary risk factors in women.

PubMed

Axelsson, John; Lowden, Arne; Kecklund, Göran

2006-01-01

Shift work increases the risk for developing cardiovascular disease. There is, however, little knowledge of what aspects of shift scheduling that are detrimental and what characteristics promote good health. The aim of the present study was to evaluate whether coronary risk factors deteriorate after a hard work period and whether recovery, in the form of a week off, was sufficient to improve them. A total of 19 women worked an extremely rapidly rotating and clockwise shift schedule at a paper and pulp factory. They underwent two health examinations, one at the end of the work period and one after the week off. In addition, the women were divided into a tolerant and a vulnerable group, depending on their satisfaction with their work hours. Most risk factors did not change, but total cholesterol and low-density lipoprotein (LDL)-cholesterol were lower after the working period than after the week-off. In addition, vulnerable women had higher levels of total cholesterol and a higher ratio of total cholesterol/high-density lipoprotein (HDL) than tolerant ones. In conclusion, the finding that a week-off worsens cholesterol levels was against our hypothesis and suggests further studies on how activities/responsibilities outside the workplace affect shift-working women. It was also shown that susceptible shift workers had worse lipid profiles.

Nonverbal auditory working memory: Can music indicate the capacity?

PubMed

Jeong, Eunju; Ryu, Hokyoung

2016-06-01

Different working memory (WM) mechanisms that underlie words, tones, and timbres have been proposed in previous studies. In this regard, the present study developed a WM test with nonverbal sounds and compared it to the conventional verbal WM test. A total of twenty-five, non-music major, right-handed college students were presented with four different types of sounds (words, syllables, pitches, timbres) that varied from two to eight digits in length. Both accuracy and oxygenated hemoglobin (oxyHb) were measured. The results showed significant effects of number of targets on accuracy and sound type on oxyHb. A further analysis showed prefrontal asymmetry with pitch being processed by the right hemisphere (RH) and timbre by the left hemisphere (LH). These findings suggest a potential for employing musical sounds (i.e., pitch and timbre) as a complementary stimuli for conventional nonverbal WM tests, which can additionally examine its asymmetrical roles in the prefrontal regions. Copyright © 2016 Elsevier Inc. All rights reserved.

ZINGRS: CO2-1 observations of strong C+ emitters at z~2

NASA Astrophysics Data System (ADS)

Scrabeck, Alex; Ferkinhoff, Carl; Brisbin, Drew; Lamarche, Cody; Vishwas, Amit; Nikola, Thomas; Stacey, Gordon J.; Higdon, James L.; Higdon, Sarah; Walter, Fabian; Decarli, Roberto

2018-06-01

We present new CO(2-1) line observations from NOEMA of five strong C+ emitting galaxies at high redshift. These galaxies, pulled from the Zeus INvestigated Galaxy Reference Sample (ZINGRS), were observed in their [CII] 158 micron line with the ZEUS instrument showing strong emission, 1 to 2% of their total far-IR luminosity. Our previous work suggests this emission is produced by normal star forming processes in photo-dissociation regions (PDRs), albeit on a galaxy wide scale fueled by cold-flow accretion. However, we could not fully exclude other mechanisms accounting for some or all of the emission. The work presented here, combining the CO emission with the [CII] 158 micron line, is consistent with PDRs being the source of the extreme C+ emission. It is further evidence for the existence of gas-rich galaxies in the early Universe undergoing galaxy-wide starbursts. These systems are not present in the nearby Universe, so represent a unique yet import evolutionary stage at early epochs.

Operation of the WWR-S Reactor in Poland and in the Period 1961-1962; DOKLAD OB ISPOL'ZOVANII I EKSPLUATATSII REAKTORA TIPA VVR-C V POL'SHE ZA 1961-1962 GODA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aleksandrowicz, J.

1963-03-01

The experimental equipment used in the work at the horizontal reactor channels is listed. Diagrams of the utilization of the nominal reactor power and core loading are given, the reactivity fractions of the separate fuel assemblies are detonated, together with the diagram of reactivity versus burnup. Reactor channels and space used for sample irradiation and isotope production are described, and the total number of irradiations is given. Results of the measurements connected with the routine reactor operation are quoted, namely: analysis of water purity in the primary circuit, analysis of the work of the ion exchanger and mechanical filter, andmore » analysis of air activity in the special ventilation system. Data are given concerning radiation protection of personnel, including individual monitoring. Leak testing of the fuel elements is discussed. Damage of the reactor equipment and appearance of alarm signals are described. (auth)« less

Use of Parallel Micro-Platform for the Simulation the Space Exploration

NASA Astrophysics Data System (ADS)

Velasco Herrera, Victor Manuel; Velasco Herrera, Graciela; Rosano, Felipe Lara; Rodriguez Lozano, Salvador; Lucero Roldan Serrato, Karen

The purpose of this work is to create a parallel micro-platform, that simulates the virtual movements of a space exploration in 3D. One of the innovations presented in this design consists of the application of a lever mechanism for the transmission of the movement. The development of such a robot is a challenging task very different of the industrial manipulators due to a totally different target system of requirements. This work presents the study and simulation, aided by computer, of the movement of this parallel manipulator. The development of this model has been developed using the platform of computer aided design Unigraphics, in which it was done the geometric modeled of each one of the components and end assembly (CAD), the generation of files for the computer aided manufacture (CAM) of each one of the pieces and the kinematics simulation of the system evaluating different driving schemes. We used the toolbox (MATLAB) of aerospace and create an adaptive control module to simulate the system.

Negative-hydrogen-ion production from a nanoporous 12CaO • 7Al2O3 electride surface

NASA Astrophysics Data System (ADS)

Sasao, Mamiko; Moussaoui, Roba; Kogut, Dmitry; Ellis, James; Cartry, Gilles; Wada, Motoi; Tsumori, Katsuyoshi; Hosono, Hideo

2018-06-01

A high production rate of negative hydrogen ions (H‑) was observed from a nanoporous 12CaO • 7Al2O3 (C12A7) electride surface immersed in hydrogen/deuterium low-pressure plasmas. The target was negatively biased at 20–130 V, and the target surface was bombarded by H3 + ions from the plasma. The production rate was compared with that from a clean molybdenum surface. Using the pseudo-exponential work-function dependence of the H‑ production rate, the total H‑ yield from the C12A7 electride surface bombarded at 80 V was evaluated to be 25% of that from a cesiated molybdenum surface with the lowest work-function. The measured H‑ energy spectrum indicates that the major production mechanism is desorption by sputtering. This material has potential to be used as a production surface of cesium-free negative ion sources for accelerators, heating beams in nuclear fusion, and surface modification for industrial applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christon, Mark A.; Baksoi, Jozsef; Barnett, Nathan

This report describes the work carried out for completion of the Thermal Hydraulics Methods (THM) Level 2 Milestone THM.CFD.P5.01 for the Consortium for Advanced Simulation of Light Water Reactors (CASL). This milestone focused primarily on the initial integration of Hydra-TH in VERA. The primary objective for this milestone was the integration of Hydra-TH as a standalone executable in VERA. A series of code extensions/modifications have been made to Hydra-TH to facilitate integration of Hydra-TH in VERA and to permit future tighter integration and physics coupling. A total of 61 serial and 64 parallel regression tests have been supplied with Hydra-TH.more » These tests are are being executed in the TriBITS environment. Once the VERA team enables the full suite of tests, the results can be posted to the VERA CDash site. Future work will consider the use of the LIME 2.0 interface for tighter integration in VERA with additional efforts focused on multiphysics coupling with radiation transport, fuel performance, and solid/structural mechanics.« less

Conductive diamond sono-electrochemical disinfection (CDSED) for municipal wastewater reclamation.

PubMed

Llanos, Javier; Cotillas, Salvador; Cañizares, Pablo; Rodrigo, Manuel A

2015-01-01

In the present work, the disinfection of actual effluents from a municipal wastewater treatment plant (WWTP) by a conductive diamond sono-electrochemical process was assessed. First, efficiency of single electrodisinfection process with diamond anodes (without the contribution of ultrasounds) was studied, finding that the total disinfection can be attained at current charges applied below 0.02kAhm(-3). It was also found that the main disinfection mechanism is the attack of Escherichia coli (E. coli) by the disinfectants produced in the electrochemical cell and that the production of chlorates is avoided when working at current densities not higher than 1.27Am(-2). Next, a marked synergistic effect was found when coupling ultrasound (US) irradiation to the electrochemical system (sono-electrochemical disinfection). This increase in the disinfection rate was found to be related to the suppression of the agglomeration of E. coli cells and the enhancement in the production of disinfectant species. Copyright © 2014 Elsevier B.V. All rights reserved.

Do nurses who work in a fair organization sleep and perform better and why? Testing potential psychosocial mediators of organizational justice.

PubMed

Hietapakka, Laura; Elovainio, Marko; Heponiemi, Tarja; Presseau, Justin; Eccles, Martin; Aalto, Anna-Mari; Pekkarinen, Laura; Kuokkanen, Liisa; Sinervo, Timo

2013-10-01

We examined whether organizational justice is associated with sleep quality and performance in a population-based sample of 1,729 Finnish registered nurses working full time. In addition, we tested psychological mechanisms mediating the potential association. The results of multivariate linear regression analyses showed higher organizational justice to be associated with fewer sleeping problems (β values range from -.20 to -.11) and higher self-reported performance (β values range from .05 to .35). Furthermore, psychological distress (related to the psychological stress model) and job involvement (related to the psychosocial resource model) mediated the association between organizational justice and sleep. Sleeping problems partly mediated the association between organizational justice and performance. Psychological distress explained 51% to 83% and job involvement explained 10% to 15% of the total effects of justice variables on sleeping problems. The findings provide support for the psychological stress model and offer practical implications for reducing nurses' sleeping problems.

What happens between pure hydraulic and buckling mechanisms of blowout fractures?

PubMed

Nagasao, Tomohisa; Miyamoto, Junpei; Shimizu, Yusuke; Jiang, Hua; Nakajima, Tatsuo

2010-06-01

The present study aims to evaluate how the ratio of the hydraulic and buckling mechanisms affects blowout fracture patterns, when these two mechanisms work simultaneously. Three-dimensional computer-aided-design (CAD)models were generated simulating ten skulls. To simulate impact, 1.2J was applied on the orbital region of these models in four patterns. Pattern 1: All the energy works to cause the hydraulic effect. Pattern 2: Two-thirds of the energy works to cause the hydraulic effect; one-third of the energy works to cause the buckling effect. Pattern 3: One-third of the energy works to cause the hydraulic effect; two-thirds of the energy works to cause the buckling effect. Pattern 4: The entire energy quantum works to cause the buckling effect. Using the finite element method, the regions where fractures were theoretically expected to occur were calculated and were compared between the four patterns. More fracture damage occurred for Pattern 1 than Pattern 2, and for Pattern 3 than for Pattern 4. The hydraulic and buckling mechanisms interact with one another. When these two mechanisms are combined, the orbital walls tend to develop serious fractures. Copyright (c) 2009 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

DNA Polymerase ζ is essential for hexavalent chromium-induced mutagenesis

PubMed Central

O'Brien, Travis J.; Witcher, Preston; Brooks, Bradford; Patierno, Steven R.

2009-01-01

Translesion synthesis (TLS) is a unique DNA damage tolerance mechanism involved in the replicative bypass of genetic lesions in favor of uninterrupted DNA replication. TLS is critical for the generation of mutations by many different chemical and physical agents, however, there is no information available regarding the role of TLS in carcinogenic metal-induced mutagenesis. Hexavalent chromium (Cr(VI))-containing compounds are highly complex genotoxins possessing both mutagenic and clastogenic activities. The focus of this work was to determine the impact that TLS has on Cr(VI)-induced mutagenesis in S. cerevisiae. Wild-type yeast and strains deficient in TLS polymerases (i.e. Polζ (rev3), Polη (rad30)) were exposed to Cr(VI) and monitored for cell survival and forward mutagenesis at the CAN1 locus. In general, TLS deficiency had little impact on Cr(VI)-induced clonogenic lethality or cell growth. rad30 yeast exhibited higher levels of basal and induced mutagenesis compared to Wt and rev3 yeast. In contrast, rev3 yeast displayed attenuated Cr(VI)-induced mutagenesis. Moreover, deletion of REV3 in rad30 yeast (rad30 rev3) resulted in a significant decrease in basal and Cr(VI) mutagenesis relative to Wt and rad30 single mutants indicating that mutagenesis primarily depended upon Polζ. Interestingly, rev3 yeast were similar to Wt yeast in susceptibility to Cr(VI)-induced frameshift mutations. Mutational analysis of the CAN1 gene revealed that Cr(VI)-induced base substitution mutations accounted for 83.9% and 100.0% of the total mutations in Wt and rev3 yeast, respectively. Insertions and deletions comprised 16.1% of the total mutations in Cr(VI) treated Wt yeast but were not observed rev3 yeast. This work provides novel information regarding the molecular mechanisms of Cr(VI)-induced mutagenesis and is the first report demonstrating a role for TLS in the fixation of mutations induced by a carcinogenic metal. PMID:19428373

Mechanics and energetics of human locomotion on sand.

PubMed

Lejeune, T M; Willems, P A; Heglund, N C

1998-07-01

Moving about in nature often involves walking or running on a soft yielding substratum such as sand, which has a profound effect on the mechanics and energetics of locomotion. Force platform and cinematographic analyses were used to determine the mechanical work performed by human subjects during walking and running on sand and on a hard surface. Oxygen consumption was used to determine the energetic cost of walking and running under the same conditions. Walking on sand requires 1.6-2.5 times more mechanical work than does walking on a hard surface at the same speed. In contrast, running on sand requires only 1.15 times more mechanical work than does running on a hard surface at the same speed. Walking on sand requires 2.1-2.7 times more energy expenditure than does walking on a hard surface at the same speed; while running on sand requires 1.6 times more energy expenditure than does running on a hard surface. The increase in energy cost is due primarily to two effects: the mechanical work done on the sand, and a decrease in the efficiency of positive work done by the muscles and tendons.

Cost optimization for buildings with hybrid ventilation systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ji, Kun; Lu, Yan

A method including: computing a total cost for a first zone in a building, wherein the total cost is equal to an actual energy cost of the first zone plus a thermal discomfort cost of the first zone; and heuristically optimizing the total cost to identify temperature setpoints for a mechanical heating/cooling system and a start time and an end time of the mechanical heating/cooling system, based on external weather data and occupancy data of the first zone.

Design and Optimization of an Austenitic TRIP Steel for Blast and Fragment Protection

NASA Astrophysics Data System (ADS)

Feinberg, Zechariah Daniel

In light of the pervasive nature of terrorist attacks, there is a pressing need for the design and optimization of next generation materials for blast and fragment protection applications. Sadhukhan used computational tools and a systems-based approach to design TRIP-120---a fully austenitic transformation-induced plasticity (TRIP) steel. Current work more completely evaluates the mechanical properties of the prototype, optimizes the processing for high performance in tension and shear, and builds models for more predictive power of the mechanical behavior and austenite stability. Under quasi-static and dynamic tension and shear, the design exhibits high strength and high uniform ductility as a result of a strain hardening effect that arises with martensitic transformation. Significantly more martensitic transformation occurred under quasi-static loading conditions (69% in tension and 52% in shear) compared to dynamic loading conditions (13% tension and 5% in shear). Nonetheless, significant transformation occurs at high-strain rates which increases strain hardening, delays the onset of necking instability, and increases total energy absorption under adiabatic conditions. Although TRIP-120 effectively utilizes a TRIP effect to delay necking instability, a common trend of abrupt failure with limited fracture ductility was observed in tension and shear at all strain rates. Further characterization of the structure of TRIP-120 showed that an undesired grain boundary cellular reaction (η phase formation) consumed the fine dispersion of the metastable gamma' phase and limited the fracture ductility. A warm working procedure was added to the processing of TRIP-120 in order to eliminate the grain boundary cellular reaction from the structure. By eliminating η formation at the grain boundaries, warm-worked TRIP-120 exhibits a drastic improvement in the mechanical properties in tension and shear. In quasi-static tension, the optimized warm-worked TRIP-120 with an Mssigma( u.t.) of -13°C has a yield strength of 180 ksi (1241 MPa), uniform ductility of 0.303, and fracture ductility of 0.95, which corresponds to a 48% increase in yield strength, a 43% increase in uniform ductility, and a 254% increase in fracture ductility relative to the designed processing of TRIP-120. The highest performing condition of warm-worked TRIP-120 in quasi-static shear with an Mssigma( sh) of 58°C exhibits a shear yield strength of 95.1 ksi (656 MPa), shear fracture strain of 144%, and energy dissipation density of 1099 MJ/m3, which corresponds to a shear yield strength increase of 61%, a shear fracture strain increase of 55%, and an energy dissipation density increase of 76%. A wide range of austenite stabilities can be achieved by altering the heat treatment times and temperatures, which significantly alters the mechanical properties. Although performance cannot be optimized for tension and shear simultaneously, different heat treatments can be applied to warm-worked TRIP-120 to achieve high performance in tension or shear. Parametric models calibrated with three-dimensional atom probe data played a crucial role in guiding the predictive process optimization of TRIP-120. Such models have been built to provide the predictive capability of inputting warm working and aging conditions and outputting the resulting structure, austenite stability, and mechanical properties. The predictive power of computational models has helped identify processing conditions that have improved the performance of TRIP-120 in tension and shear and can be applied to future designs that optimize for adiabatic conditions.

[Design of an external prosthetic system with a polycentric mechanism].

PubMed

Valentino Orozco, Gerardo Alejandro; Guerrero Beltrán, Leobardo; Obregón Velasco, Dinora; Avalos Fernández, Oscar

2008-01-01

This medical and engineering work explains the process carried out to build a four-barred polycentric knee mechanism using a mechanical actuator for modular prosthetics. Imitation of the knee performance was the main goal, as well as to cover the basic needs of amputated patients with a low production cost. The polycentric knee mechanism was developed in three stages. The first one was the design and building of the four-barred mechanism using materials as stainless steel 304 and aluminum 6,061 which both have high reliability, corrosion resistance and a relatively easy modeling capability. The total mass was of 700 g. Autocad was used for design and effort analysis was done by using ANSYS. At the end of the first stage, it was observed that its density did not allow mass optimization and no assistant actuator was available for the walking movement. In the second stage, mechanism mass estimation was done by using Alumold 400; this material brings lower density than stainless steel keeping strength and fatigue resistance higher than aluminum 6061. The better ergonomic device was built; a mechanical actuator based on a spring was implemented and tested on two female patients, one geriatric and one 16 years old. The third stage will be described in a future publication, the device mass was optimized by using poly-tetra-fluor-ethylene enhanced with carbon and carbon fiber. Also, the mechanical actuator was complemented with reo-magnetic liquid addition and an electronic control. At the end of this research, an external polycentric knee mechanism was developed, by observing movement stages, velocities, ergonomics, shapes, sizes and significant weights of Mexican patients. Effort analysis by finite element was done and it was determined that the mechanism was capable of modifying its center of rotation according to the knee flexion angle making it a polycentric mechanisms. Also, it was tested on two patients, both females, one 16 and one 75 years old.

Empirical retrocausality: Testing physics hypotheses with parapsychological experiments

NASA Astrophysics Data System (ADS)

Dobyns, York

2017-05-01

In 2011, Daryl Bem published a report of nine parapsychological experiments showing evidence of retrocausal information transfer. Earlier in 2016, the team of Bem, Tressoldi, Rabeyron, and Duggan published the results of a meta-analysis containing 81 independent replications of the original Bem experiments (total of 90 with the originals).[1] This much larger database continues to show positive results of generally comparable effect size, thus demonstrating that the effects claimed by Bem can be replicated by independent researchers and greatly strengthening the case for empirically observed retrocausation. Earlier (2011) work by this author showed how a modification of one of Bem's original experiments could be used to test the mechanism implicitly proposed by Echeverria, Klinkhammer, and Thorne to explain how retrocausal phenomena can exist without any risk of self-contradictory event sequences (time paradoxes). In light of the new publication and new evidence, the current work generalizes the previous analysis which was restricted to only one of Bem's experimental genres (precognitive approach and avoidance). The current analysis shows how minor modifications can be made in Bem's other experimental genres of retroactive priming, retroactive habituation, and retroactive facilitation of recall to test the EKT anti-paradox mechanism. If the EKT hypothesis is correct, the modified experiments, while continuing to show replicable retrocausal phenomena, will also show a characteristic pattern of distortion in the statistics of the random selections used to drive the experiments.

COAGGREGATION OCCURS AMONGST BACTERIA WITHIN AND BETWEEN DOMESTIC SHOWERHEAD BIOFILMS

PubMed Central

Vornhagen, Jay; Stevens, Michael; McCormick, David; Dowd, Scot E.; Eisenberg, Joseph N.S.; Boles, Blaise R.; Rickard, Alexander H.

2014-01-01

Showerheads support the development multi-species biofilms that can be unsightly, produce malodor, and may harbor pathogens. The outer surface spray plates of many showerheads support visible biofilms that likely contain a mixture of bacteria from freshwater and potentially from human users. Coaggregation, a mechanism by which genetically distinct bacteria specifically recognize one another, may contribute to the retention and enrichment of different species within these biofilms. The aim of this work was to identify the bacterial composition of outer spray plate biofilms of three domestic shower heads and to determine the inter- and intra-biofilm coaggregation ability of each culturable isolate. The bacterial composition of the three biofilms was determined by using bacterial tag-encoded FLX amplicon pyrosequencing (bTEFAP) and by culturing on R2A medium. An average of 31 genera per biofilm were identified using bTEFAP and a total of 30 isolates were cultured. Even though the microbial diversity of each showerhead biofilm differed, every cultured isolate was able to coaggregate with at least one other isolate from the same or different showerhead biofilm. Promiscuous coaggregating isolates belonged to the genera Brevundimonas, Micrococcus, and Lysobacter. This work suggests that coaggregation may be a common feature of showerhead biofilms. Characterization of the mechanisms mediating coaggregation, and the inter-species interactions they facilitate, may allow for novel strategies to inhibit biofilm development. PMID:23194413

The 2017 Nonlinear Mechanics and Dynamics Research Institute.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuether, Robert J.; Allensworth, Brooke Marie; Peebles, Diane E.

The 2017 Nonlinear Mechanics and Dynamics (NOMAD) Research Institute was successfully held from June 19 to July 28, 2017. NOMAD seeks to bring together participants with diverse tec hnical backgrounds to work in small teams to utilize an interactive approach to cultivate new ideas and approaches in engineering . NOMAD provides an opportunity for researchers - especially early career researchers - to develop lasting collaborations that go beyond what can be established from the limited interactions at their institutions or at annual conferences. A total of 17 students from around the world came to Albuquerque, New Mexico to participate inmore » the six - week long program held at the University of New Mexico campus. The students collaborated on one of six research projects that were developed by various mentors from Sandia National Laboratories, academia, and other government laboratories. In addition to the research activities, the students atte nded weekly technical seminars, toured the National Museum of Nuclear Science & History, and socialized at various off - hour events including an Albuquerque Isotopes baseball game. At the end of the summer, the students gave a final technical presentation o n their research findings that was broadcast via Skype. Many of the research discoveries made at NOMAD are published as proceedings at t echnical conference s and have direct alignment with the critical mission work performed at Sandia.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sills, Alison; Glebbeek, Evert; Chatterjee, Sourav

We created artificial color-magnitude diagrams of Monte Carlo dynamical models of globular clusters and then used observational methods to determine the number of blue stragglers in those clusters. We compared these blue stragglers to various cluster properties, mimicking work that has been done for blue stragglers in Milky Way globular clusters to determine the dominant formation mechanism(s) of this unusual stellar population. We find that a mass-based prescription for selecting blue stragglers will select approximately twice as many blue stragglers than a selection criterion that was developed for observations of real clusters. However, the two numbers of blue stragglers aremore » well-correlated, so either selection criterion can be used to characterize the blue straggler population of a cluster. We confirm previous results that the simplified prescription for the evolution of a collision or merger product in the BSE code overestimates their lifetimes. We show that our model blue stragglers follow similar trends with cluster properties (core mass, binary fraction, total mass, collision rate) as the true Milky Way blue stragglers as long as we restrict ourselves to model clusters with an initial binary fraction higher than 5%. We also show that, in contrast to earlier work, the number of blue stragglers in the cluster core does have a weak dependence on the collisional parameter Γ in both our models and in Milky Way globular clusters.« less

Interactive mechanism of working environments and construction behaviors with cognitive work analysis: an elevator installation case study.

PubMed

Wang, Yanqing; Chong, Heap-Yih; Liao, Pin-Chao; Ren, Hantao

2017-09-25

Unsafe behavior is a leading factor in accidents, and the working environment significantly affects behaviors. However, few studies have focused on detailed mechanisms for addressing unsafe behaviors resulting from environmental constraints. This study aims to delineate these mechanisms using cognitive work analysis (CWA) for an elevator installation case study. Elevator installation was selected for study because it involves operations at heights: falls from heights remain a major cause of construction worker mortality. This study adopts a mixed research approach based on three research methodology stages. This research deconstructs the details of the working environment, the workers' decision-making processes, the strategies chosen given environmental conditions and the conceptual model for workers' behaviors, which jointly depict environment-behavior mechanisms at length. By applying CWA to the construction industry, environmental constraints can easily be identified, and targeted engineering suggestions can be generated.

Influence of strong perturbations on wall-bounded flows

NASA Astrophysics Data System (ADS)

Buxton, O. R. H.; Ewenz Rocher, M.; Rodríguez-López, E.

2018-01-01

Single-point hot-wire measurements are made downstream of a series of spanwise repeating obstacles that are used to generate an artificially thick turbulent boundary layer. The measurements are made in the near field, in which the turbulent boundary layer is beginning to develop from the wall-bounded wakes of the obstacles. The recent paper of Rodríguez-López et al. [E. Rodríguez-López et al., Phys. Rev. Fluids 1, 074401 (2016), 10.1103/PhysRevFluids.1.074401] broadly categorized the mechanisms by which canonical turbulent boundary layers eventually develop from wall-bounded wakes into two distinct mechanisms, the wall-driven and wake-driven mechanisms. In the present work we attempt to identify the geometric parameters of tripping arrays that trigger these two mechanisms by examining the spectra of the streamwise velocity fluctuations and the intermittent outer region of the flow. Using a definition reliant upon the magnitude of the velocity fluctuations, an intermittency function is devised that can discriminate between turbulent and nonturbulent flow. These results are presented along with the spectra in order to try to ascertain which aspects of a trip's geometry are more likely to favor the wall-driven or wake-driven mechanism. The geometrical aspects of the trips tested are the aspect ratio, the total blockage, and the blockage at the wall. The results indicate that the presence, or not, of perforations is the most significant factor in affecting the flow downstream. The bleed of fluid through the perforations reenergizes the mean recirculation and leads to a narrower intermittent region with a more regular turbulent-nonturbulent interface. The near-wall turbulent motions are found to recover quickly downstream of all of the trips with a wall blockage of 50%, but a clear influence of the outer fluctuations, generated by the tip vortices of the trips, is observed in the near-wall region for the high total blockage trips. The trip with 100% wall blockage is found to modify the nature of the inner-wall peak of turbulent kinetic energy.

Acute decrease of left ventricular mechanical dyssynchrony and improvement of contractile state and energy efficiency after left ventricular restoration.

PubMed

Schreuder, Jan J; Castiglioni, Alessandro; Maisano, Francesco; Steendijk, Paul; Donelli, Andrea; Baan, Jan; Alfieri, Ottavio

2005-01-01

Surgical left ventricular restoration by means of endoventricular patch aneurysmectomy in patients with postinfarction aneurysm should result in acute improved left ventricular performance by decreasing mechanical dyssynchrony and increasing energy efficiency. Nine patients with left ventricular postinfarction aneurysm were studied intraoperatively before and after ventricular restoration with a conductance volume catheter to analyze pressure-volume relationships, energy efficiency, and mechanical dyssynchrony. The end-systolic elastance was used as a load-independent index of contractile state. Left ventricular energy efficiency was calculated from stroke work and total pressure-volume area. Segmental volume changes perpendicular to the long axis were used to calculate mechanical dyssynchrony. Statistical analysis was performed with the paired t test and least-squares linear regression. Endoventricular patch aneurysmectomy reduced end-diastolic volume by 37% (P < .001), with unchanged stroke volume. Systolic function improved, as derived from increased +dP/dt(max), by 42% (P < .03), peak ejection rate by 28% (P < .02), and ejection fraction by 16% (P < .0002). Early diastolic function improved, as shown by reduction of -dP/dt(max) by 34% (P < .006) and shortened tau by 30% (P < .001). Left ventricular end-systolic elastance increased from 1.2 +/- 0.6 to 2.2 +/- 1 mm Hg/mL (P < .001). Left ventricular energy efficiency increased by 36% (P < .002). Left ventricular mechanical dyssynchrony decreased during systole by 33% (P < .001) and during diastole by 20% (P < .005). Left ventricular restoration induced acute improvements in contractile state, energy efficiency, and relaxation, together with a decrease in left ventricular mechanical dyssynchrony.

A survey of the relationship between work schedule and its effect on the fatigue of rescue personnel in Isfahan with a standard method of CIS202

PubMed Central

Habibi, Ehsanollah; Soury, Shiva; Vardanjani, Hassan Rajabi; Khodarahmi, Behnam; Dehghan, Habibollah; Hosseini, Mohsen; Esmaeli, Hamid; Khademi, Abolfazl

2015-01-01

Context: Fatigue is a factor that can have negative effects on family life, social relationship and work. Work schedule is one of the affective factors on personnel's fatigue in different jobs. In this study, the work schedule and its effect on rescue personnel in Isfahan are explored. Aims: The purpose of this study was to investigate the relationship between work schedules and fatigue among rescue personnel. Settings and Design: This study is periodical and has been conducted on 72 employees of rescue personnel in Isfahan. Materials and Methods: Random sampling was done and the primary data that was collected through fatigue assessment questionnaire after being conducted as a pilot study on 10% of samples were collected to confirm the validity of this study. Finally, the data was given to SPSS11.5 software and were analyzed by descriptive statistics and linear digression. Results: The results showed that from the statistical point of view some parts of work schedules like work hours satisfaction, resting time and work order on total fatigue are effective in linear and inverse way but the item “predictibility of work conditions” does not have a meaningful relationship with total fatigue. Furthermore, the results showed that there is a meaningful and inverse relationship with work hours, resting time and work order with mental fatigue and also the work schedule has a meaningful, linear and inverse relation with mental fatigue and total fatigue. Conclusions: By increasing the satisfaction of working hours, increasing resting time and also with an increase of work order the total fatigue of rescue personnel will decrease. PMID:27462640

Surgical Thoracic Transplant Training: Super Fellowship-Is It Super?

PubMed

Makdisi, George; Makdisi, Tony; Caldeira, Christiano C; Wang, I-Wen

2017-10-11

The quality of training provided to thoracic transplant fellows is a critical step in the care of complex patients undergoing transplant. The training varies since it is not an accreditation council for graduate medical education accredited fellowship. A total of 104 heart or lung transplant program directors throughout the United States were sent a survey of 24 questions focusing on key aspects of training, fellowship training content and thoracic transplant job satisfaction. Out of the 104 programs surveyed 45 surveys (43%) were returned. In total, 26 programs offering a transplant fellowship were included in the survey. Among these programs 69% currently have fellows of which 56% are American Board of Thoracic Surgery board eligible. According to the United Network for Organ Sharing (UNOS) requirements, 46% of the programs do not meet the requirements to be qualified as a primary heart transplant surgeon. A total of 23% of lung transplant programs also perform less than the UNOS minimum requirements. Only 24% have extra-surgical curriculum. Out of the participating programs, only 38% of fellows secured a job in a hospital setting for performing transplants. An astounding 77% of replies site an unpredictable work schedule as the main reason that makes thoracic transplant a less than favorable profession among new graduates. Long hours were also a complaint of 69% of graduates who agreed that their personal life is affected by excessive work hours. Annually, almost half of all thoracic transplant programs perform fewer than the UNOS requirements to be a primary thoracic surgeon. This results in a majority of transplant fellows not finding a suitable transplant career. The current and future needs for highly qualified thoracic transplant surgeons will not be met through our existing training mechanisms. Copyright © 2017 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Dust exposure during small-scale mining in Tanzania: a pilot study.

PubMed

Bratveit, Magne; Moen, Bente E; Mashalla, Yohana J S; Maalim, Hatua

2003-04-01

Small-scale mining in developing countries is generally labour-intensive and carried out with low levels of mechanization. In the Mererani area in the northern part of Tanzania, there are about 15000 underground miners who are constantly subjected to a poor working environment. Gemstones are found at depths down to 500 m. The objectives of this pilot study were to monitor the exposure to dust during work processes, which are typical of small-scale mining in developing countries, and to make a rough estimation of whether there is a risk of chronic pulmonary diseases for the workers. Personal sampling of respirable dust (n = 15) and 'total' dust (n = 5) was carried out during three consecutive days in one mine, which had a total of 50 workers in two shifts. Sampling started immediately before the miners entered the shaft, and lasted until they reappeared at the mine entrance after 5-8 h. The median crystalline silica content and the combustible content of the respirable dust samples were 14.2 and 5.5%, respectively. When drilling, blasting and shovelling were carried out, the exposure measurements showed high median levels of respirable dust (15.5 mg/m(3)), respirable crystalline silica (2.4 mg/m(3)), respirable combustible dust (1.5 mg/m(3)) and 'total' dust (28.4 mg/m(3)). When only shovelling and loading of sacks took place, the median exposures to respirable dust and respirable crystalline silica were 4.3 and 1.1 mg/m(3). This study shows that the exposure to respirable crystalline silica was high during underground small-scale mining. In the absence of personal protective equipment, the miners in the Mererani area are presumably at a high risk of developing chronic silicosis.

Pre-gravid physical activity and reduced risk of glucose intolerance in pregnancy: the role of insulin sensitivity.

PubMed

Retnakaran, Ravi; Qi, Ying; Sermer, Mathew; Connelly, Philip W; Zinman, Bernard; Hanley, Anthony J G

2009-04-01

Pre-gravid physical activity has been associated with a reduced risk of gestational diabetes mellitus (GDM), although neither the types of exercise nor the physiologic mechanisms underlying this protective effect have been well-studied. Thus, we sought to study the relationships between types of pre-gravid physical activity and metabolic parameters in pregnancy, including glucose tolerance, insulin sensitivity and beta-cell function. A total of 851 women underwent a glucose challenge test (GCT) and a 3-h oral glucose tolerance test (OGTT) in late pregnancy, yielding four glucose tolerance groups: (i) GDM; (ii) gestational impaired glucose tolerance (GIGT); (iii) abnormal GCT with normal glucose tolerance on OGTT (abnormal GCT NGT); and (iv) normal GCT with NGT on OGTT (normal GCT NGT). Pre-gravid physical activity was assessed using the Baecke questionnaire, which measures (i) total physical activity and (ii) its three component domains: work, nonsport leisure-time, and vigorous/sports activity. Glucose tolerance status improved across increasing quartiles of pre-gravid total physical activity (P = 0.0244). Whereas neither work nor nonsport leisure-time activity differed between glucose tolerance groups, pre-gravid vigorous/sports activity was significantly higher in women with normal GCT NGT compared to women with (i) abnormal GCT NGT (P = 0.0018) (ii) GIGT (P = 0.0025), and (iii) GDM (P = 0.0044). In particular, vigorous/sports activity correlated with insulin sensitivity (measured by IS(OGTT)) (r = 0.21, P < 0.0001). Furthermore, on multiple linear regression analysis, pre-gravid vigorous/sports activity emerged as a significant independent predictor of IS(OGTT) in pregnancy (t = 4.97, P < 0.0001). Pre-gravid vigorous/sports activity is associated with a reduced risk of glucose intolerance in pregnancy, an effect likely mediated by enhanced insulin sensitivity.

Total and domain-specific sitting time among employees in desk-based work settings in Australia.

PubMed

Bennie, Jason A; Pedisic, Zeljko; Timperio, Anna; Crawford, David; Dunstan, David; Bauman, Adrian; van Uffelen, Jannique; Salmon, Jo

2015-06-01

To describe the total and domain-specific daily sitting time among a sample of Australian office-based employees. In April 2010, paper-based surveys were provided to desk-based employees (n=801) in Victoria, Australia. Total daily and domain-specific (work, leisure-time and transport-related) sitting time (minutes/day) were assessed by validated questionnaires. Differences in sitting time were examined across socio-demographic (age, sex, occupational status) and lifestyle characteristics (physical activity levels, body mass index [BMI]) using multiple linear regression analyses. The median (95% confidence interval [CI]) of total daily sitting time was 540 (531-557) minutes/day. Insufficiently active adults (median=578 minutes/day, [95%CI: 564-602]), younger adults aged 18-29 years (median=561 minutes/day, [95%CI: 540-577]) reported the highest total daily sitting times. Occupational sitting time accounted for almost 60% of total daily sitting time. In multivariate analyses, total daily sitting time was negatively associated with age (unstandardised regression coefficient [B]=-1.58, p<0.001) and overall physical activity (minutes/week) (B=-0.03, p<0.001) and positively associated with BMI (B=1.53, p=0.038). Desk-based employees reported that more than half of their total daily sitting time was accrued in the work setting. Given the high contribution of occupational sitting to total daily sitting time among desk-based employees, interventions should focus on the work setting. © 2014 Public Health Association of Australia.

Impact of total laryngectomy on return to work.

PubMed

Costa, Jose Miguel; López, Montserrat; García, Jacinto; León, Xavier; Quer, Miquel

Total laryngectomy is one of the most mutilating oncological operations. There are no specific studies evaluating return to work after this surgery. A cross-sectional study was performed on a sample of 116 laryngectomized patients who were disease- free and had a minimum follow-up of 2 years from total laryngectomy. A survey was conducted to find out their employment situation before and after surgery. At the time of surgery, 62 (53%) were working, 40 (35%) were retired and 14 (12%) were in a disability situation. 60% had professions with low qualification requirements, the largest group being construction workers. Of the 62 patients active at the time of total laryngectomy, 29 became inactive and 33 (53%) maintained their work activity. The most important factors in maintaining work activity were the level of professional qualification and the method of vocal rehabilitation. Eighty percent of the patients with high-intermediate qualification maintained their jobs, compared to 35% of those with low professional qualifications (P<.001). Seventy percent of the patients with voice prostheses maintained their work activity, compared to 31% of the patients rehabilitated with oesophageal voice (P=.004). Logistic regression confirmed these as independent variables for continuing to work. This is the first study that analyzes the impact of total laryngectomy on the work situation. The most important factors for a return to work were having a high-intermediate skilled job and the use of voice prosthesis as a method of vocal rehabilitation. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Otorrinolaringología y Cirugía de Cabeza y Cuello. All rights reserved.

A Guide to Laboratory Practicum on Mechanics

NASA Astrophysics Data System (ADS)

Rusu, A. S.; Rusu, S. S.; Pirtac, C.

2012-12-01

The Guide represent a Laboratory practicum in mechanics for students from the Technical University of Moldova. The works are modernized as compared with older ones put in 1964 by Computer assistance. Each work contains theoretical framework, a work instruction and control questions. The Guide contains 27 figures.

Successful Training of Filtering Mechanisms in Multiple Object Tracking Does Not Transfer to Filtering Mechanisms in a Visual Working Memory Task: Behavioral and Electrophysiological Evidence

ERIC Educational Resources Information Center

Arend, Anna M.; Zimmer, Hubert D.

2012-01-01

In this training study, we aimed to selectively train participants' filtering mechanisms to enhance visual working memory (WM) efficiency. The highly restricted nature of visual WM capacity renders efficient filtering mechanisms crucial for its successful functioning. Filtering efficiency in visual WM can be measured via the lateralized change…

Computer-aided analysis of star shot films for high-accuracy radiation therapy treatment units

NASA Astrophysics Data System (ADS)

Depuydt, Tom; Penne, Rudi; Verellen, Dirk; Hrbacek, Jan; Lang, Stephanie; Leysen, Katrien; Vandevondel, Iwein; Poels, Kenneth; Reynders, Truus; Gevaert, Thierry; Duchateau, Michael; Tournel, Koen; Boussaer, Marlies; Cosentino, Dorian; Garibaldi, Cristina; Solberg, Timothy; De Ridder, Mark

2012-05-01

As mechanical stability of radiation therapy treatment devices has gone beyond sub-millimeter levels, there is a rising demand for simple yet highly accurate measurement techniques to support the routine quality control of these devices. A combination of using high-resolution radiosensitive film and computer-aided analysis could provide an answer. One generally known technique is the acquisition of star shot films to determine the mechanical stability of rotations of gantries and the therapeutic beam. With computer-aided analysis, mechanical performance can be quantified as a radiation isocenter radius size. In this work, computer-aided analysis of star shot film is further refined by applying an analytical solution for the smallest intersecting circle problem, in contrast to the gradient optimization approaches used until today. An algorithm is presented and subjected to a performance test using two different types of radiosensitive film, the Kodak EDR2 radiographic film and the ISP EBT2 radiochromic film. Artificial star shots with a priori known radiation isocenter size are used to determine the systematic errors introduced by the digitization of the film and the computer analysis. The estimated uncertainty on the isocenter size measurement with the presented technique was 0.04 mm (2σ) and 0.06 mm (2σ) for radiographic and radiochromic films, respectively. As an application of the technique, a study was conducted to compare the mechanical stability of O-ring gantry systems with C-arm-based gantries. In total ten systems of five different institutions were included in this study and star shots were acquired for gantry, collimator, ring, couch rotations and gantry wobble. It was not possible to draw general conclusions about differences in mechanical performance between O-ring and C-arm gantry systems, mainly due to differences in the beam-MLC alignment procedure accuracy. Nevertheless, the best performing O-ring system in this study, a BrainLab/MHI Vero system, and the best performing C-arm system, a Varian Truebeam system, showed comparable mechanical performance: gantry isocenter radius of 0.12 and 0.09 mm, respectively, ring/couch rotation of below 0.10 mm for both systems and a wobble of 0.06 and 0.18 mm, respectively. The methodology described in this work can be used to monitor mechanical performance constancy of high-accuracy treatment devices, with means available in a clinical radiation therapy environment.

29 CFR 516.23 - Employees of hospitals and residential care facilities compensated for overtime work on the basis...

Code of Federal Regulations, 2011 CFR

2011-07-01

... paragraphs (a) (5) and (7) through (9), and in addition: (1) Time of day and day of week on which the... period, (3) Total straight-time wages paid for hours worked during the 14-day period, (4) Total overtime... compensated for overtime work on the basis of a 14-day work period pursuant to section 7(j) of the Act. 516.23...

Selection of software for mechanical engineering undergraduates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheah, C. T.; Yin, C. S.; Halim, T.

A major problem with the undergraduate mechanical course is the limited exposure of students to software packages coupled with the long learning curve on the existing software packages. This work proposes the use of appropriate software packages for the entire mechanical engineering curriculum to ensure students get sufficient exposure real life design problems. A variety of software packages are highlighted as being suitable for undergraduate work in mechanical engineering, e.g. simultaneous non-linear equations; uncertainty analysis; 3-D modeling software with the FEA; analysis tools for the solution of problems in thermodynamics, fluid mechanics, mechanical system design, and solid mechanics.

Influence of social presence on eye movements in visual search tasks.

PubMed

Liu, Na; Yu, Ruifeng

2017-12-01

This study employed an eye-tracking technique to investigate the influence of social presence on eye movements in visual search tasks. A total of 20 male subjects performed visual search tasks in a 2 (target presence: present vs. absent) × 2 (task complexity: complex vs. simple) × 2 (social presence: alone vs. a human audience) within-subject experiment. Results indicated that the presence of an audience could evoke a social facilitation effect on response time in visual search tasks. Compared with working alone, the participants made fewer and shorter fixations, larger saccades and shorter scan path in simple search tasks and more and longer fixations, smaller saccades and longer scan path in complex search tasks when working with an audience. The saccade velocity and pupil diameter in the audience-present condition were larger than those in the working-alone condition. No significant change in target fixation number was observed between two social presence conditions. Practitioner Summary: This study employed an eye-tracking technique to examine the influence of social presence on eye movements in visual search tasks. Results clarified the variation mechanism and characteristics of oculomotor scanning induced by social presence in visual search.

On total noncommutativity in quantum mechanics

NASA Astrophysics Data System (ADS)

Lahti, Pekka J.; Ylinen, Kari

1987-11-01

It is shown within the Hilbert space formulation of quantum mechanics that the total noncommutativity of any two physical quantities is necessary for their satisfying the uncertainty relation or for their being complementary. The importance of these results is illustrated with the canonically conjugate position and momentum of a free particle and of a particle closed in a box.

12 CFR 3.131 - Mechanics for calculating total wholesale and retail risk-weighted assets.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 1 2014-01-01 2014-01-01 false Mechanics for calculating total wholesale and...: (1) Phase 1—categorization of exposures; (2) Phase 2—assignment of wholesale obligors and exposures... amounts. (b) Phase 1—Categorization. The national bank or Federal savings association must determine which...

Comparison of high-intensity sound and mechanical vibration for cleaning porous titanium cylinders fabricated using selective laser melting.

PubMed

Seiffert, Gary; Hopkins, Carl; Sutcliffe, Chris

2017-01-01

Orthopedic components, such as the acetabular cup in total hip joint replacement, can be fabricated using porous metals, such as titanium, and a number of processes, such as selective laser melting. The issue of how to effectively remove loose powder from the pores (residual powder) of such components has not been addressed in the literature. In this work, we investigated the feasibility of two processes, acoustic cleaning using high-intensity sound inside acoustic horns and mechanical vibration, to remove residual titanium powder from selective laser melting-fabricated cylinders. With acoustic cleaning, the amount of residual powder removed was not influenced by either the fundamental frequency of the horn used (75 vs. 230 Hz) or, for a given horn, the number of soundings (between 1 and 20). With mechanical vibration, the amount of residual powder removed was not influenced by the application time (10 vs. 20 s). Acoustic cleaning was found to be more reliable and effective in removal of residual powder than cleaning with mechanical vibration. It is concluded that acoustic cleaning using high-intensity sound has significant potential for use in the final preparation stages of porous metal orthopedic components. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 117-123, 2017. © 2015 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc.

Variation of mechanical properties and oxidation with radiation dose and source in highly crosslinked remelted UHMWPE.

PubMed

Fung, Mitchell; Bowsher, John G; Van Citters, Douglas W

2018-06-01

Ultra-high molecular weight polyethylene (UHMWPE) is the current gold standard for bearing materials used in total joint arthroplasty. High-dose radiation is commonly used to crosslink UHMWPE, thereby improving its wear resistance. A subsequent remelting step eliminates trapped residual free radicals to promote oxidative stability on the shelf, and to prevent material degradation over the long term. Assessment of clinically retrieved, highly crosslinked UHMWPE devices shows signs of unanticipated oxidation occurring in vivo, despite the absence of free radicals prior to implantation. These findings warrant further investigation into possible factors impacting this phenomenon along with its clinical implications. The overall objective of this work is to quantify the influence of irradiation dose and source on UHMWPE's oxidative stability, along with the effects of oxidation on the ultimate mechanical properties, including strength, ductility, and toughness. The results showed a strong positive correlation between maximum oxidation and initial transvinylene content. Critical oxidation levels in the context of mechanical property loss were determined for e-beam and gamma treatments at various radiation doses. Further, it was shown that critical oxidation was more dependent on radiation dose and less dependent on source. If in vivo oxidation persists in these devices, this can potentially lead to mechanical failure (e.g. fatigue damage) as observed in terminally gamma-sterilized devices. Copyright © 2018 Elsevier Ltd. All rights reserved.

Date palm biochar-polymer composites: An investigation of electrical, mechanical, thermal and rheological characteristics.

PubMed

Poulose, Anesh Manjaly; Elnour, Ahmed Yagoub; Anis, Arfat; Shaikh, Hamid; Al-Zahrani, S M; George, Justin; Al-Wabel, Mohammad I; Usman, Adel R; Ok, Yong Sik; Tsang, Daniel C W; Sarmah, Ajit K

2018-04-01

The application of biochar (BC) as a filler in polymers can be viewed as a sustainable approach that incorporates pyrolysed waste based value-added material and simultaneously mitigate bio-waste in a smart way. The overarching aim of this work was to investigate the electrical, mechanical, thermal and rheological properties of biocomposite developed by utilizing date palm waste-derived BC for the reinforcing of polypropylene (PP) matrix. Date palm waste derived BC prepared at (700 and 900°C) were blended at different proportions with polypropylene and the resultant composites (BC/PP) were characterized using an array of techniques (scanning electron microscope, energy-dispersive X-ray spectroscopy and Fourier transform infra-red spectroscopy). Additionally the thermal, mechanical, electrical and rheological properties of the BC/PP composites were evaluated at different loading of BC content (from 0 to15% w/w). The mechanical properties of BC/PP composites showed an improvement in the tensile modulus while that of electrical characterization revealed an enhanced electrical conductivity with increased BC loading. Although the BC incorporation into the PP matrix has significantly reduced the total crystallinity of the resulted composites, however; a positive effect on the crystallization temperature (T c ) was observed. The rheological characterization of BC/PP composites revealed that the addition of BC had minimal effect on the storage modulus (G') compared to the neat (PP). Copyright © 2017 Elsevier B.V. All rights reserved.

Psychocultural Mechanisms of the Propensity toward Criminal Homicide: A Multidimensional View of the Culture of Honor

PubMed Central

Souza, Monica G. T. C.; Souza, Bruno C.; Roazzi, Antonio; da Silva, Edson S.

2017-01-01

Introduction: Theory of the Culture of Honor is one of the few models in criminology specifically geared toward homicide. It proposes that, in certain societies, men must never show weakness and are required to react violently to any perceived threats to their reputation, thereby increasing their probability of committing a homicide. This has been suggested as the main explanation for the high rates of this type of crime in Brazil, particularly in the Northeast. Underlying this explanation there are complex mechanisms and processes that have yet to be clarified. Objectives: The present research aimed to investigate the workings of the possible psychocultural mechanisms underlying the culture of honor and the process through which they might affect the individual propensity toward homicide. Methods: A total of 336 Brazilian adults were assessed regarding a broad range of sociodemographic, psychological, and sociocultural variables, including their attitudes toward homicide. The resulting dataset was analyzed using Smallest Space Analysis and Facet Theory. Results: It seems that certain cultural elements associated to traditional masculinity and enhanced anger tend to promote negative personality traits and increase one’s propensity toward committing homicide. Conclusion: The findings obtained not only confirm the Theory of the Culture of Honor for the propensity toward homicide, but also explicit and clarify some of the psychocultural processes and mechanisms involved, suggesting a new scientific framework. PMID:29163264

The epidemiology and possible mechanisms of disinfection by-products in drinking water.

PubMed

Nieuwenhuijsen, Mark J; Grellier, James; Smith, Rachel; Iszatt, Nina; Bennett, James; Best, Nicky; Toledano, Mireille

2009-10-13

This paper summarizes the epidemiological evidence for adverse health effects associated with disinfection by-products (DBPs) in drinking water and describes the potential mechanism of action. There appears to be good epidemiological evidence for a relationship between exposure to DBPs, as measured by trihalomethanes (THMs), in drinking water and bladder cancer, but the evidence for other cancers including colorectal cancer is inconclusive and inconsistent. There appears to be some evidence for an association between exposure to DBPs, specifically THMs, and little for gestational age/intrauterine growth retardation and, to a lesser extent, pre-term delivery, but evidence for relationships with other outcomes such as low birth weight, stillbirth, congenital anomalies and semen quality is inconclusive and inconsistent. Major limitations in exposure assessment, small sample sizes and potential biases may account for the inconclusive and inconsistent results in epidemiological studies. Moreover, most studies have focused on total THMs as the exposure metric, whereas other DBPs appear to be more toxic than the THMs, albeit generally occurring at lower levels in the water. The mechanisms through which DBPs may cause adverse health effects including cancer and adverse reproductive effects have not been well investigated. Several mechanisms have been suggested, including genotoxicity, oxidative stress, disruption of folate metabolism, disruption of the synthesis and/or secretion of placental syncytiotrophoblast-derived chorionic gonadotropin and lowering of testosterone levels, but further work is required in this area.

[Analysis of the mechanisms of minor occupational injuries in the construction industry in Spain].

PubMed

Benavides, F G; Giráldez, M T; Castejón, E; Catot, N; Zaplana, M; Delclós, J; Benach, J; Gimeno, D

2003-01-01

The construction industry produces the highest number of occupational injuries in Spain (25.6%). Of these, 98.5% were minor injuries with 5 million workdays lost in 2000. This occurred even after the recent introduction of numerous health and occupational safety regulations. The objective of the present study was to identify the specific mechanisms of minor occupational injuries in the construction sector. In 2000, there were 235,853 minor occupational injuries in the construction industry. From these, injuries in general construction and civil engineering were selected (n = 155,044). These injuries affected both the total number of workers in the sector as well as bricklayers and unskilled construction workers. Insurance and financial activities (n = 2,019) were selected as a reference economic sector. Minor occupational injuries due to nontraumatic processes (heart attack, etc.) were taken as a control group (n = 167), assuming that the risk of nontraumatic processes was independent of economic activities. Odds ratios (OR) were adjusted by age, sex, years of work experience, type of employment and company size through nonconditional logistic regression models. The mechanisms with the highest risk of minor occupational lesions in construction workers as a group compared with employees in the financial sector were projection of fragments (OR = 33.0; 95% CI, 15.3-70.8) and being struck by objects (OR = 18.2; CI 95%, 9.7-34.1). These were also the most specific mechanisms of injury in the subgroup of bricklayers and unskilled construction workers. Activities aimed at preventing minor occupational injuries in the construction sector should be orientated towards these mechanisms, especially projection of fragments despite the low frequency of this mechanism compared with that of other mechanisms. Case-control design is a useful alternative approach for research into occupational injuries.

New mechanism for autocatalytic decomposition of H2CO3 in the vapor phase.

PubMed

Ghoshal, Sourav; Hazra, Montu K

2014-04-03

In this article, we present high level ab initio calculations investigating the energetics of a new autocatalytic decomposition mechanism for carbonic acid (H2CO3) in the vapor phase. The calculation have been performed at the MP2 level of theory in conjunction with aug-cc-pVDZ, aug-cc-pVTZ, and 6-311++G(3df,3pd) basis sets as well as at the CCSD(T)/aug-cc-pVTZ level. The present study suggests that this new decomposition mechanism is effectively a near-barrierless process at room temperature and makes vapor phase of H2CO3 unstable even in the absence of water molecules. Our calculation at the MP2/aug-cc-pVTZ level predicts that the effective barrier, defined as the difference between the zero-point vibrational energy (ZPE) corrected energy of the transition state and the total energy of the isolated starting reactants in terms of bimolecular encounters, is nearly zero for the autocatalytic decomposition mechanism. The results at the CCSD(T)/aug-cc-pVTZ level of calculations suggest that the effective barrier, as defined above, is sensitive to some extent to the levels of calculations used, nevertheless, we find that the effective barrier height predicted at the CCSD(T)/aug-cc-pVTZ level is very small or in other words the autocatalytic decomposition mechanism presented in this work is a near-barrierless process as mentioned above. Thus, we suggest that this new autocatalytic decomposition mechanism has to be considered as the primary mechanism for the decomposition of carbonic acid, especially at its source, where the vapor phase concentration of H2CO3 molecules reaches its highest levels.

Synthesis of wrinkled mesoporous silica and its reinforcing effect for dental resin composites.

PubMed

Wang, Ruili; Habib, Eric; Zhu, X X

2017-10-01

The aim of this work is to explore the reinforcing effect of wrinkled mesoporous silica (WMS), which should allow micromechanical resin matrix/filler interlocking in dental resin composites, and to investigate the effect of silica morphology, loading, and compositions on their mechanical properties. WMS (average diameter of 496nm) was prepared through the self-assembly method and characterized by the use of the electron microscopy, dynamic light scattering, and the N 2 adsorption-desorption measurements. The mechanical properties of resin composites containing silanized WMS and nonporous smaller silica were evaluated with a universal mechanical testing machine. Field-emission scanning electron microscopy was used to study the fracture morphology of dental composites. Resin composites including silanized silica particles (average diameter of 507nm) served as the control group. Higher filler loading of silanized WMS substantially improved the mechanical properties of the neat resin matrix, over the composites loaded with regular silanized silica particles similar in size. The impregnation of smaller secondary silica particles with diameters of 90 and 190nm, denoted respectively as Si90 and Si190, increased the filler loading of the bimodal WMS filler (WMS-Si90 or WMS-Si190) to 60wt%, and the corresponding composites exhibited better mechanical properties than the control fillers made with regular silica particles. Among all composites, the optimal WMS-Si190- filled composite (mass ratio WMS:Si190=10:90, total filler loading 60wt%) exhibited the best mechanical performance including flexural strength, flexural modulus, compressive strength and Vickers microhardness. The incorporation of WMS and its mixed bimodal fillers with smaller silica particles led to the design and formulation of dental resin composites with superior mechanical properties. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Work-Home Interference, Perceived Total Workload, and the Risk of Future Sickness Absence Due to Stress-Related Mental Diagnoses Among Women and Men: a Prospective Twin Study.

PubMed

Svedberg, Pia; Mather, Lisa; Bergström, Gunnar; Lindfors, Petra; Blom, Victoria

2018-02-01

Work-home interference has been proposed as an important explanation for sickness absence (SA). Previous studies show mixed results, have not accounted for familial factors (genetics and shared everyday environment), or investigated diagnosis specific SA. The aim was to study whether work-home interference and perceived total workload predict SA due to stress-related mental diagnoses, or SA due to other mental diagnoses, among women and men, when adjusting for various confounders and familial factors. This study included 11,916 twins, 19-47 years (49% women). Data on work-to-home and home-to-work conflicts, perceived total workload, and relevant confounders were derived from a 2005 survey, and national register data on SA spells until 2013 were obtained. Odds ratios (ORs) with 95% confidence intervals (CIs) were calculated. Discordant twin pair design was applied to adjust for familial factors. Each one unit increase in work-to-home and home-to-work conflicts, and perceived total workload was associated with higher odds for SA due to stress-related mental diagnoses and to SA due to other mental diagnoses among women, when adjusting for sociodemographic factors (ORs 1.15-1.31). Including health or familial factors, no associations remained. For men, each one unit increase in work-to-home conflicts was associated with higher odds for SA due to stress-related diagnoses (ORs 1.23-1.35), independently of confounders. Work-to-home conflict was independently associated with future SA due to stress-related diagnoses among men only. Health- and work-related factors seem to be important confounders when researching work-home interference, perceived total workload, and SA. Not including such confounders involves risking drawing incorrect conclusions. Further studies are needed to confirm sex differences and whether genetic factors are important for the associations studied.

Aggregation work at polydisperse micellization: ideal solution and "dressed micelle" models comparing to molecular dynamics simulations.

PubMed

Burov, S V; Shchekin, A K

2010-12-28

General thermodynamic relations for the work of polydisperse micelle formation in the model of ideal solution of molecular aggregates in nonionic surfactant solution and the model of "dressed micelles" in ionic solution have been considered. In particular, the dependence of the aggregation work on the total concentration of nonionic surfactant has been analyzed. The analogous dependence for the work of formation of ionic aggregates has been examined with regard to existence of two variables of a state of an ionic aggregate, the aggregation numbers of surface active ions and counterions. To verify the thermodynamic models, the molecular dynamics simulations of micellization in nonionic and ionic surfactant solutions at two total surfactant concentrations have been performed. It was shown that for nonionic surfactants, even at relatively high total surfactant concentrations, the shape and behavior of the work of polydisperse micelle formation found within the model of the ideal solution at different total surfactant concentrations agrees fairly well with the numerical experiment. For ionic surfactant solutions, the numerical results indicate a strong screening of ionic aggregates by the bound counterions. This fact as well as independence of the coefficient in the law of mass action for ionic aggregates on total surfactant concentration and predictable behavior of the "waterfall" lines of surfaces of the aggregation work upholds the model of "dressed" ionic aggregates.

Impact of endometriosis on quality of life and work productivity: a multicenter study across ten countries.

PubMed

Nnoaham, Kelechi E; Hummelshoj, Lone; Webster, Premila; d'Hooghe, Thomas; de Cicco Nardone, Fiorenzo; de Cicco Nardone, Carlo; Jenkinson, Crispin; Kennedy, Stephen H; Zondervan, Krina T

2011-08-01

To assess the impact of endometriosis on health-related quality of life (HRQoL) and work productivity. Multicenter cross-sectional study with prospective recruitment. Sixteen clinical centers in ten countries. A total of 1,418 premenopausal women, aged 18-45 years, without a previous surgical diagnosis of endometriosis, having laparoscopy to investigate symptoms or to be sterilized. None. Diagnostic delay, HRQoL, and work productivity. There was a delay of 6.7 years, principally in primary care, between onset of symptoms and a surgical diagnosis of endometriosis, which was longer in centers where women received predominantly state-funded health care (8.3 vs. 5.5 years). Delay was positively associated with the number of pelvic symptoms (chronic pelvic pain, dysmenorrhoea, dyspareunia, and heavy periods) and a higher body mass index. Physical HRQoL was significantly reduced in affected women compared with those with similar symptoms and no endometriosis. Each affected woman lost on average 10.8 hours (SD 12.2) of work weekly, mainly owing to reduced effectiveness while working. Loss of work productivity translated into significant costs per woman/week, from US$4 in Nigeria to US$456 in Italy. Endometriosis impairs HRQoL and work productivity across countries and ethnicities, yet women continue to experience diagnostic delays in primary care. A higher index of suspicion is needed to expedite specialist assessment of symptomatic women. Future research should seek to clarify pain mechanisms in relation to endometriosis severity. Copyright © 2011 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Impact of endometriosis on quality of life and work productivity: a multicenter study across ten countries

PubMed Central

Nnoaham, Kelechi E.; Hummelshoj, Lone; Webster, Premila; d’Hooghe, Thomas; Nardone, Fiorenzo de Cicco; Nardone, Carlo de Cicco; Jenkinson, Crispin; Kennedy, Stephen H.; Zondervan, Krina T.

2013-01-01

Objective To assess the impact of endometriosis on health-related quality of life (HRQoL) and work productivity. Design Multicenter cross-sectional study with prospective recruitment. Setting Sixteen clinical centers in ten countries. Patient(s) A total of 1,418 premenopausal women, aged 18–45 years, without a previous surgical diagnosis of endometriosis, having laparoscopy to investigate symptoms or to be sterilized. Intervention(s) None. Main Outcome Measure(s) Diagnostic delay, HRQoL, and work productivity. Result(s) There was a delay of 6.7 years, principally in primary care, between onset of symptoms and a surgical diagnosis of endometriosis, which was longer in centers where women received predominantly state-funded health care (8.3 vs. 5.5 years). Delay was positively associated with the number of pelvic symptoms (chronic pelvic pain, dysmenorrhoea, dyspareunia, and heavy periods) and a higher body mass index. Physical HRQoL was significantly reduced in affected women compared with those with similar symptoms and no endometriosis. Each affected woman lost on average 10.8 hours (SD 12.2) of work weekly, mainly owing to reduced effectiveness while working. Loss of work productivity translated into significant costs per woman/week, from US$4 in Nigeria to US$456 in Italy. Conclusion(s) Endometriosis impairs HRQoL and work productivity across countries and ethnicities, yet women continue to experience diagnostic delays in primary care. A higher index of suspicion is needed to expedite specialist assessment of symptomatic women. Future research should seek to clarify pain mechanisms in relation to endometriosis severity. PMID:21718982

A methodologic approach for normalizing angular work and velocity during isotonic and isokinetic eccentric training.

PubMed

Guilhem, Gaël; Cornu, Christophe; Guével, Arnaud

2012-01-01

Resistance exercise training commonly is performed against a constant external load (isotonic) or at a constant velocity (isokinetic). Researchers comparing the effectiveness of isotonic and isokinetic resistance-training protocols need to equalize the mechanical stimulus (work and velocity) applied. To examine whether the standardization protocol could be adjusted and applied to an eccentric training program. Controlled laboratory study. Controlled research laboratory. Twenty-one sport science male students (age = 20.6 ± 1.5 years, height = 178.0 ± 4.0 cm, mass = 74.5 ± 9.1 kg). Participants performed 9 weeks of isotonic (n = 11) or isokinetic (n = 10) eccentric training of knee extensors that was designed so they would perform the same amount of angular work at the same mean angular velocity. Angular work and angular velocity. The isotonic and isokinetic groups performed the same total amount of work (-185.2 ± 6.5 kJ and -184.4 ± 8.6 kJ, respectively) at the same angular velocity (21 ± 1°/s and 22°/s, respectively) with the same number of repetitions (8.0 and 8.0, respectively). Bland-Altman analysis showed that work (bias = 2.4%) and angular velocity (bias = 0.2%) were equalized over 9 weeks between the modes of training. The procedure developed allows angular work and velocity to be standardized over 9 weeks of isotonic and isokinetic eccentric training of the knee extensors. This method could be useful in future studies in which researchers compare neuromuscular adaptations induced by each type of training mode with respect to rehabilitating patients after musculoskeletal injury.

Work-Related Unintentional Injuries Associated With Hurricane Sandy in New Jersey.

PubMed

Marshall, Elizabeth G; Lu, Shou-En; Shi, Zhengyang; Swerdel, Joel; Borjan, Marija; Lumia, Margaret E

2016-06-01

We aimed to evaluate the occurrence of work-related injuries after Hurricane Sandy potentially related to response and recovery. Emergency and hospital discharges (patients aged 18-65 years) with a diagnosis of unintentional injury were obtained from the New Jersey Department of Health. Work-related injuries were identified as those with a workers' compensation payer or other work-related codes. Counties were categorized as high-, medium-, or low-impact areas. Poisson regression analysis was used to compare the rate of work-related injury the year following Sandy landfall with the 3 previous years. Total work-related injuries declined the week immediately after Sandy (rate ratio [RR]: 0.85; 95% confidence interval [CI]: 0.69-1.05) and no overall increase was found in the year after Hurricane Sandy. However, high-impact counties showed an elevated risk of work-related injuries in the first and third quarters after Hurricane Sandy among men, especially for blacks and Hispanics. The greatest excesses occurred in the third quarter after the storm, May to July, for falls (RR: 1.30; 95% CI: 1.08-1.57), cut/pierce injuries (RR: 1.24; 95% CI: 1.09-1.40), struck-by injuries (RR: 1.17; 95% CI: 1.02-1.34), and overexertion (RR: 1.26; 95% CI: 1.10-1.44). Hospital data suggested an increase in injuries associated with rebuilding and recovery rather than with initial response. Future efforts aimed at prevention should evaluate the mechanisms and circumstances of injury in more detail. (Disaster Med Public Health Preparedness. 2016;10:394-404).

Federal Employees’ Compensation Act: DOD Access to DOL Data is Generally Sufficient, but Monitoring Timelines Could Help Return-to-Work Efforts

DTIC Science & Technology

2016-09-01

percent of FECA claimants in 2015, and DOD total- disability beneficiaries (i.e., with no capacity to work) were generally older than those from the...including the nearly 20 percent receiving partial- or total- disability benefits. About 56 percent of DOD total- disability beneficiaries were at or...DOD Federal Employees’ Compensation Act (FECA) Total- Disability Beneficiaries at or above Their Full Social Security Retirement Age, 2015 Notes

How cannabis causes paranoia: using the intravenous administration of ∆9-tetrahydrocannabinol (THC) to identify key cognitive mechanisms leading to paranoia.

PubMed

Freeman, Daniel; Dunn, Graham; Murray, Robin M; Evans, Nicole; Lister, Rachel; Antley, Angus; Slater, Mel; Godlewska, Beata; Cornish, Robert; Williams, Jonathan; Di Simplicio, Martina; Igoumenou, Artemis; Brenneisen, Rudolf; Tunbridge, Elizabeth M; Harrison, Paul J; Harmer, Catherine J; Cowen, Philip; Morrison, Paul D

2015-03-01

Paranoia is receiving increasing attention in its own right, since it is a central experience of psychotic disorders and a marker of the health of a society. Paranoia is associated with use of the most commonly taken illicit drug, cannabis. The objective was to determine whether the principal psychoactive ingredient of cannabis-∆(9)-tetrahydrocannabinol (THC)-causes paranoia and to use the drug as a probe to identify key cognitive mechanisms underlying paranoia. A randomized, placebo-controlled, between-groups test of the effects of intravenous THC was conducted. A total of 121 individuals with paranoid ideation were randomized to receive placebo, THC, or THC preceded by a cognitive awareness condition. Paranoia was assessed extensively via a real social situation, an immersive virtual reality experiment, and standard self-report and interviewer measures. Putative causal factors were assessed. Principal components analysis was used to create a composite paranoia score and composite causal variables to be tested in a mediation analysis. THC significantly increased paranoia, negative affect (anxiety, worry, depression, negative thoughts about the self), and a range of anomalous experiences, and reduced working memory capacity. The increase in negative affect and in anomalous experiences fully accounted for the increase in paranoia. Working memory changes did not lead to paranoia. Making participants aware of the effects of THC had little impact. In this largest study of intravenous THC, it was definitively demonstrated that the drug triggers paranoid thoughts in vulnerable individuals. The most likely mechanism of action causing paranoia was the generation of negative affect and anomalous experiences. © The Author 2014. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center.

A Study for the Restoration of Hong Dae-Yong Honsangui - Focusing on the structure and operating mechanism

NASA Astrophysics Data System (ADS)

Lee, Yong Sam; Kim, Sang Hyuk; Park, Je Hoon

2013-09-01

Honsangui (celestial globe) which is a water-hammering method astronomical clock is recorded in "Juhaesuyong" which is Volume VI of supplement from "Damheonseo", written by Hong Dae-Yong (1731~1783). We made out the conceptual design of Hong Dae-Yong's Honsangui through the study on its structure and working mechanism. Honsangui consist of three rings and two layers, the structure of rings which correspond to outer layer is similar to his own Tongcheonui (armillary sphere) which is a kind of armillary sphere. Honsang sphere which correspond to inner layer depicts constellations and milky way and two beads hang on it as Sun and Moon respectively for realize the celestial motion. Tongcheonui is operated by the pendulum power but Honsangui is operated by water-hammering method mechanism. This Honsangui's working mechanism is the traditional way of Joseon and it was simplified the working mechanism of Shui y'n i hsiang t'ai which is a representative astronomical clock of China. This record of Honsangui is the only historical record about the water-hammering method working mechanism of Joseon Era and it provide the study of water-hammering method mechanism with a vital clue.

Influence of stretch-shortening cycle on mechanical behaviour of triceps surae during hopping.

PubMed

Belli, A; Bosco, C

1992-04-01

Six subjects performed a first series of vertical plantar flexions and a second series of vertical rebounds, both involving muscle triceps surae exclusively. Vertical displacements, vertical forces and ankle angles were recorded during the entire work period of 60 seconds per series. In addition, expired gases were collected during the test and recovery for determination of the energy expenditure. Triceps surae was mechanically modelled with a contractile component and with an elastic component. Mechanical behaviour and work of the different muscle components were determined in both series. The net muscular efficiency calculated from the work performed by the centre of gravity was 17.5 +/- 3.0% (mean +/- SD) in plantar flexions and 29.9 +/- 4.8% in vertical rebounds. The net muscle efficiency calculated from the work performed by the contractile component was 17.4 +/- 2.9% in plantar flexions and 16.1 +/- 1.4% in vertical rebounds. These results suggest that the muscular efficiency differences do not reflect muscle contractile component efficiency but essentially the storage and recoil of elastic energy. This is supported by the relationship (P less than 0.01) found in vertical rebounds between the extra work and the elastic component work. A detailed observation of the mechanical behaviour of muscle mechanical components showed that the strategy to maximize the elastic work depends also on the force-velocity characteristics of the movement and that the eccentric-concentric work of the contractile component does not always correspond respectively to the ankle extension-flexion.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Prashant; Harbola, Manoj K.; Johnson, Duane D.

Here, this work constitutes a comprehensive and improved account of electronic-structure and mechanical properties of silicon-nitride (more » $${\\rm Si}_{3}$$ $${\\rm N}_{4}$$ ) polymorphs via van Leeuwen and Baerends (LB) exchange-corrected local density approximation (LDA) that enforces the exact exchange potential asymptotic behavior. The calculated lattice constant, bulk modulus, and electronic band structure of $${\\rm Si}_{3}$$ $${\\rm N}_{4}$$ polymorphs are in good agreement with experimental results. We also show that, for a single electron in a hydrogen atom, spherical well, or harmonic oscillator, the LB-corrected LDA reduces the (self-interaction) error to exact total energy to ~10%, a factor of three to four lower than standard LDA, due to a dramatically improved representation of the exchange-potential.« less

New Insights in Tropospheric Ozone and its Variability

NASA Technical Reports Server (NTRS)

Oman, Luke D.; Douglass, Anne R.; Ziemke, Jerry R.; Rodriquez, Jose M.

2011-01-01

We have produced time-slice simulations using the Goddard Earth Observing System Version 5 (GEOS-5) coupled to a comprehensive stratospheric and tropospheric chemical mechanism. These simulations are forced with observed sea surface temperatures over the past 25 years and use constant specified surface emissions, thereby providing a measure of the dynamically controlled ozone response. We examine the model performance in simulating tropospheric ozone and its variability. Here we show targeted comparisons results from our simulations with a multi-decadal tropical tropospheric column ozone dataset obtained from satellite observations of total column ozone. We use SHADOZ ozonesondes to gain insight into the observed vertical response and compare with the simulated vertical structure. This work includes but is not limited to ENSO related variability.

Failure models for textile composites

NASA Technical Reports Server (NTRS)

Cox, Brian

1995-01-01

The goals of this investigation were to: (1) identify mechanisms of failure and determine how the architecture of reinforcing fibers in 3D woven composites controlled stiffness, strength, strain to failure, work of fracture, notch sensitivity, and fatigue life; and (2) to model composite stiffness, strength, and fatigue life. A total of 11 different angle and orthogonal interlock woven composites were examined. Composite properties depended on the weave architecture, the tow size, and the spatial distributions and strength of geometrical flaws. Simple models were developed for elastic properties, strength, and fatigue life. A more complicated stochastic model, called the 'Binary Model,' was developed for damage tolerance and ultimate failure. These 3D woven composites possessed an extraordinary combination of strength, damage tolerance, and notch insensitivity.

Removal of gadolinium nitrate from heavy water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilde, E.W.

2000-03-22

Work was conducted to develop a cost-effective process to purify 181 55-gallon drums containing spent heavy water moderator (D2O) contaminated with high concentrations of gadolinium nitrate, a chemical used as a neutron poison during former nuclear reactor operations at the Savannah River Site (SRS). These drums also contain low level radioactive contamination, including tritium, which complicates treatment options. Presently, the drums of degraded moderator are being stored on site. It was suggested that a process utilizing biological mechanisms could potentially lower the total cost of heavy water purification by allowing the use of smaller equipment with less product loss andmore » a reduction in the quantity of secondary waste materials produced by the current baseline process (ion exchange).« less

Superasymmetric fission of heavy nuclei induced by intermediate-energy protons

NASA Astrophysics Data System (ADS)

Deppman, A.; Andrade-II, E.; Guimarães, V.; Karapetyan, G. S.; Tavares, O. A. P.; Balabekyan, A. R.; Demekhina, N. A.; Adam, J.; Garcia, F.; Katovsky, K.

2013-12-01

In this work we present the results for the investigation of intermediate-mass fragment (IMF) production with the proton-induced reaction at 660 MeV on 238U and 237Np target. The data were obtained with the LNR Phasotron U-400M Cyclotron at Joint Institute for Nuclear Research (JINR), Dubna, Russia. A total of 93 isotopes, in the mass range of 30

29 CFR 5.15 - Limitations, variations, tolerances, and exemptions under the Contract Work Hours and Safety...

Code of Federal Regulations, 2011 CFR

2011-07-01

...). (iii) The time in question does not involve productive work or performance of the apprentice's or... receives gross wages of not less than $300 per week regardless of the total number of hours worked in any workweek, and (B) Within any workweek the total wages which an employee receives are not less than the...

Selective attention on representations in working memory: cognitive and neural mechanisms.

PubMed

Ku, Yixuan

2018-01-01

Selective attention and working memory are inter-dependent core cognitive functions. It is critical to allocate attention on selected targets during the capacity-limited working memory processes to fulfill the goal-directed behavior. The trends of research on both topics are increasing exponentially in recent years, and it is considered that selective attention and working memory share similar underlying neural mechanisms. Different types of attention orientation in working memory are introduced by distinctive cues, and the means using retrospective cues are strengthened currently as it is manipulating the representation in memory, instead of the perceptual representation. The cognitive and neural mechanisms of the retro-cue effects are further reviewed, as well as the potential molecular mechanism. The frontal-parietal network that is involved in both attention and working memory is also the neural candidate for attention orientation during working memory. Neural oscillations in the gamma and alpha/beta oscillations may respectively be employed for the feedforward and feedback information transfer between the sensory cortices and the association cortices. Dopamine and serotonin systems might interact with each other subserving the communication between memory and attention. In conclusion, representations which attention shifts towards are strengthened, while representations which attention moves away from are degraded. Studies on attention orientation during working memory indicates the flexibility of the processes of working memory, and the beneficial way that overcome the limited capacity of working memory.

Selective attention on representations in working memory: cognitive and neural mechanisms

PubMed Central

2018-01-01

Selective attention and working memory are inter-dependent core cognitive functions. It is critical to allocate attention on selected targets during the capacity-limited working memory processes to fulfill the goal-directed behavior. The trends of research on both topics are increasing exponentially in recent years, and it is considered that selective attention and working memory share similar underlying neural mechanisms. Different types of attention orientation in working memory are introduced by distinctive cues, and the means using retrospective cues are strengthened currently as it is manipulating the representation in memory, instead of the perceptual representation. The cognitive and neural mechanisms of the retro-cue effects are further reviewed, as well as the potential molecular mechanism. The frontal-parietal network that is involved in both attention and working memory is also the neural candidate for attention orientation during working memory. Neural oscillations in the gamma and alpha/beta oscillations may respectively be employed for the feedforward and feedback information transfer between the sensory cortices and the association cortices. Dopamine and serotonin systems might interact with each other subserving the communication between memory and attention. In conclusion, representations which attention shifts towards are strengthened, while representations which attention moves away from are degraded. Studies on attention orientation during working memory indicates the flexibility of the processes of working memory, and the beneficial way that overcome the limited capacity of working memory. PMID:29629245

An energy harvesting converter to power sensorized total human knee prosthesis

NASA Astrophysics Data System (ADS)

Luciano, V.; Sardini, E.; Serpelloni, M.; Baronio, G.

2014-02-01

Monitoring the internal loads acting in a total knee prosthesis (TKP) is fundamental aspect to improve their design. One of the main benefits of this improvement is the longer duration of the tibial inserts. In this work, an electromagnetic energy harvesting system, which is implantable in a TKP, is presented. This is conceived for powering a future implantable system that is able to monitor the loads (and, possibly, other parameters) that could influence the working conditions of a TKP in real-time. The energy harvesting system (EHS) is composed of two series of NdFeB magnets, positioned into each condyle, and a coil that is placed in a pin of the tibial insert and connected to an implantable power management circuit. The magnetic flux variation and the induced voltage are generated by the knee's motion. A TKP prototype has been realized in order to reproduce the knee mechanics and to test the EHS performance. In the present work, the experimental results are obtained by adopting a resistive load of 2.2 kΩ, in order to simulate a real implanted autonomous system with a current consumption of 850 µA and voltage of 2 V. The tests showed that, after 7 to 30 s of walking with a gait cycle frequency of about 1.0 Hz, the EHS can generate an energy of about 70 μJ, guaranteeing a voltage between 2 and 1.4 V every 7.6 s. With this prototype we can verify that it is possible to power for 16 ms a circuit having a power consumption of 1.7 mW every 7.6 s. The proposed generator is a viable solution to power an implanted electronic system that is conceived for measuring and transmitting the TKP load parameters.