Reactivity of the cadmium ion in concentrated phosphoric acid solutions.

PubMed

De Gyves, J; Gonzales, J; Louis, C; Bessiere, J

1989-07-01

The solvation transfer coefficients which characterize the changes of ion reactivity with phosphoric acid concentration have been calculated for cadmium from the constants of the successive chloride complexes, and for silver and diethyldithiophosphate from potentiometric measurements. They evidence the strong desolvation of the cadmium species in concentrated phosphoric acid media, causing a remarkable increase of its reactivity. They allow the results of liquid-liquid extraction, precipitation and flotation reactions to be correctly interpreted and their changes to be foreseen when the reagents are modified.

Characterization and recovery of mercury from spent fluorescent lamps.

PubMed

Jang, Min; Hong, Seung Mo; Park, Jae K

2005-01-01

Fluorescent lamps rely on mercury as the source of ultraviolet radiation for the production of visible light. Partitioning of mercury among vapor phase, loose phosphor powders produced during breaking and washing steps, glass matrices, phosphor powders attached on the glass and aluminum end caps was examined from simulated laboratory lamp recycling tests for different types of spent and new fluorescent lamps. Mercury concentrations in lamp glasses taken from commercial lamp recyclers were also analyzed for comparison with the simulated results of spent and new lamps of different types. The mercury content of the glass from spent lamps was highly variable depending on the lamp type and manufacturer; the median values of the mercury concentration in glasses for spent 26- (T8) and 38-mm (T12) diameter fluorescent lamps were approximately 30 and 45 microg/g, respectively. The average mercury concentration of samples taken from recycler A was 29.6 microg/g, which was about 64% of median value measured from the spent T12 lamps. Over 94% of total mercury in lamps remained either as a component of phosphor powders attached inside the lamp or in glass matrices. New T12 lamps had a higher partitioning percentage of elemental mercury in the vapor phase (0.17%) than spent T12 lamps (0.04%), while spent lamps had higher partitioning percentages of mercury resided on end-caps and phosphor powders detached from the breaking and washing steps. The TCLP values of simulated all lamp-glasses and samples obtained from recyclers were higher than the limit of LDR standard (0.025 mg/L). After investigating acid treatment and high temperature treatment as mercury reclamation techniques, it was found that heating provided the most effective mercury capture. Although the initial mercury concentrations of individual sample were different, the mercury concentrations after 1 h exposure at 100 degrees C were below 4 mug/g for all samples (i.e., <1% remaining). Therefore, it is recommended that heating be used for recovering mercury from spent fluorescent lamps.

Comparison of Four Strong Acids on the Precipitation Potential of Gypsum in Brines During Distillation of Pretreated, Augmented Urine

NASA Technical Reports Server (NTRS)

Muirhead, Dean

2011-01-01

Two batches of nominally pretreated and augmented urine were prepared with the baseline pretreatment formulation of sulfuric acid and chromium trioxide. The urine was augmented with inorganic salts and organic compounds in order to simulate a urinary ionic concentrations representing the upper 95 percentile on orbit. Three strong mineral acids: phosphoric, hydrochloric, and nitric acid, were substituted for the sulfuric acid for comparison to the baseline sulfuric acid pretreatment formulation. Three concentrations of oxidizer in the pretreatment formulation were also tested. Pretreated urine was distilled to 85% water recovery to determine the effect of each acid and its conjugate base on the precipitation of minerals during distillation. The brines were analyzed for calcium and sulfate ion, total, volatile, and fixed suspended solids. Test results verified that substitution of phosphoric, hydrochloric, or nitric acids for sulfuric acid would prevent the precipitation of gypsum up to 85% recovery from pretreated urine representing the upper 95 percentile calcium concentration on orbit.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubey, Vikas, E-mail: jsvikasdubey@gmail.com; Kaur, Jagjeet

Present paper reports synthesis and characterization of trivalent cerium (Ce{sup 3+}) doped zirconium dioxide (ZrO{sub 2}) phosphors. Effect of variable concentration of cerium on photoluminescence (PL) is studied. Samples were prepared by combustion synthesis technique which is suitable for less time taking techniques also for large scale production for phosphors. Starting material used for sample preparation are Zr(NO{sub 3}){sub 3} and Ce(NO{sub 3}){sub 3} and urea used as a fuel. All prepared phosphor with variable concentration of Ce{sup 3+} (0.1 to 2mol%) was studied by photoluminescence analysis it is found that the excitation spectra of prepared phosphor shows broad excitationmore » centred at 390nm. The excitation spectra with variable concentration of Ce{sup 3+} show strong peaks at 447nm. Spectrophotometric determinations of peaks are evaluated by Commission Internationale de I’Eclairage technique. Using this phosphor, the desired CIE values including emissions throughout the violet (390 nm) and blue (427 nm) of the spectra were achieved. Efficient blue light emitting diodes were fabricated using Ce{sup 3+} doped phosphor based on near ultraviolet (NUV) excited LED lights.« less

Thermo and mechanoluminescence of Dy3+ activated K2Mg2(SO4)3 phosphor

NASA Astrophysics Data System (ADS)

Panigrahi, A. K.; Dhoble, S. J.; Kher, R. S.; Moharil, S. V.

2003-08-01

A solid state diffusion method for the preparation of (K2 : Dy)Mg2(SO4)3 and (K2 : Dy,P)Mg2(SO4)3 phosphors is reported. Thermoluminescence (TL) and mechanoluminescence (ML) characteristics are studied. TL, shown by the (K2 : Dy,P)Mg2(SO4)3 phosphor is 60% as intense as the conventional CaSO4 : Dy phosphor used in the TLD of ionization radiation. It has a linear TL dose response and a negligible fading. These properties of (K2 : Dy,P)Mg2(SO4)3 should be suitable in dosimetry of ionization radiation using TL technique. ML of (K2 : Dy)Mg2(SO4)3 shows one peak which has been observed in ML intensity versus time curve. The ML peak shows the recombination of electrons with free radicals (anion radicals produced by γ-irradiation) released from traps during the mechanical pressure applied on the Dy activated K2Mg2(SO4)3 phosphor. This ML mechanism is proposed for γ-irradiated sulfate based phosphors. It has been found that the total light output, i.e. ML intensity, increases with concentration of dopant, strain rate and irradiation dose of the phosphor. Mechanoluminescence and ML emission spectra of (K2 : Dy)Mg2(SO4)3 were recorded for better understanding of the ML process. The TL and ML measurements have also been performed to elucidate the mechanism of ML. Some correlation between ML and TL has also been found.

Electroformed Nanocrystalline Coatings: An Advanced Alternative to Hard Chrome Electroplating

DTIC Science & Technology

2003-11-21

hypo/ phosphorous acid was included in the estimate. The cost analysis is given in Table 2-3. The relative consumable cost for the nanocrystalline...concentrations and phosphorous acid concentrations. While the internal stress of the Co- P deposit was affected by changes in the above-mentioned...may be occurring which consumes the phosphorous acid in solution (see Section 2.2). Table 5-1 Hardness at distance from deposit/substrate

Production of technical grade phosphoric acid from incinerator sewage sludge ash (ISSA).

PubMed

Donatello, S; Tong, D; Cheeseman, C R

2010-01-01

The recovery of phosphorus from sewage sludge ash samples obtained from 7 operating sludge incinerators in the UK using a sulfuric acid washing procedure to produce a technical grade phosphoric acid product has been investigated. The influences of reaction time, sulfuric acid concentration, liquid to solid ratio and source of ISSA on P recovery have been examined. The optimised conditions were the minimum stoichiometric acid requirement, a reaction time of 120 min and a liquid to solid ratio of 20. Under these conditions, average recoveries of between 72% and 91% of total phosphorus were obtained. Product filtrate was purified by passing through a cation exchange column, concentrated to 80% H(3)PO(4) and compared with technical grade H(3)PO(4) specifications. The economics of phosphate recovery by this method are briefly discussed. 2010 Elsevier Ltd. All rights reserved.

Full down-conversion of amber-emitting phosphor-converted light-emitting diodes with powder phosphors and a long-wave pass filter.

PubMed

Oh, Jeong Rok; Cho, Sang-Hwan; Park, Hoo Keun; Oh, Ji Hye; Lee, Yong-Hee; Do, Young Rag

2010-05-24

This paper reports the possibility of a facile optical structure to realize a highly efficient monochromatic amber-emitting light-emitting diode (LED) using a powder-based phosphor-converted LED combined with a long-wave pass filter (LWPF). The capping of a blue-reflecting and amber-passing LWPF enhances both the amber emission from the silicate amber phosphor layer and the color purity due to the blocking and recycling of the pumping blue light from the InGaN LED. The enhancement of the luminous efficacy of the amber pc-LED with a LWPF (phosphor concentration 20 wt%, 39.4 lm/W) is 34% over that of an amber pc-LED without a LWPF (phosphor concentration 55 wt%, 29.4 lm/W) at 100 mA and a high color purity (>96%) with Commission International d'Eclairage (CIE) color coordinates of x=0.57 and y=0.42.

The effects of apple pomace, bentonite and calcium superphosphate on swine manure aerobic composting.

PubMed

Jiang, Jishao; Huang, Yimei; Liu, Xueling; Huang, Hua

2014-09-01

The effects of additives such as apple pomace, bentonite and calcium superphosphate on swine manure composting were investigated in a self-built aerated static box (90 L) by assessing their influences on the transformation of nitrogen, carbon, phosphorous and compost maturity. The results showed that additives all prolonged the thermophilic stage in composting compared to control. Nitrogen losses amounted to 34-58% of the initial nitrogen, in which ammonia volatilization accounted for 0.3-4.6%. Calcium superphosphate was helpful in facilitating composting process as it significantly reduced the ammonia volatilization during thermophilic stage and increased the contents of total nitrogen and phosphorous in compost, but bentonite increased the ammonia volatilization and reduced the total nitrogen concentration. It suggested that calcium superphosphate is an effective additive for keeping nitrogen during swine manure composting. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sol–gel synthesis, structure and luminescence properties of Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yuntong; Liu, Xiaohua, E-mail: xhliuxhliu@tom.com

2015-04-15

Graphical abstract: The phosphor powders of Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} were prepared by sol–gel method. The dependence of luminescence intensity on the Eu{sup 3+} concentration was investigated. - Highlights: • We synthesize Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} phosphors by the sol–gel method. • The effect of temperature on the crystallinity and morphology is investigated. • The phosphor presents an intense CT band in near UV range (370–410 nm). • The concentration quenching mechanism is the exchange interaction. - Abstract: Double-perovskite Ba{sub 2}Zn{sub 1−x}MoO{sub 6}:xEu{sup 3+} (x = 0, 0.02, 0.04, 0.06, 0.08, 0.1) orange–red emitting phosphors were synthesized by using themore » sol–gel method. The crystalline structure and photoluminescence properties of the phosphors were investigated. The X-ray diffraction (XRD) patterns indicate that the structure of matrix Ba{sub 2}ZnMoO{sub 6} is cubic double-perovskite with space group Fm-3m. The Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} phosphors present an intense broad charge transfer (CT) band absorption in near UV range (370–410 nm), which attributes to the charge transfer state of MoO{sub 6}, and performs orange–red emission of Eu{sup 3+} ({sup 5}D{sub 0} → {sup 7}F{sub 1} transition) at around 596 nm. A low concentration quenching occurs in Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} and the optimal doping concentration is about 6 mol%. The Ba{sub 2}ZnMoO{sub 6}:Eu{sup 3+} phosphors are considered to be a promising orange–red emitting phosphor for near ultraviolet GaN-based white light emitting diode.« less

Influence of Annealing Temperature and Gd and Eu Concentrations on Structure and Luminescence Properties of (Y,Gd)BO3:Eu3+ Phosphors Prepared by Sol-Gel Method

NASA Astrophysics Data System (ADS)

Lien, N. T. K.; Thang, N. V.; Hung, N. D.; Cuong, N. D.; Kien, N. D. T.; Thang, C. X.; Vuong, P. H.; Viet, D. X.; Khoi, N. T.; Huy, P. T.

2017-06-01

Red-emitting Eu3+-doped (Y,Gd)BO3 phosphors have been synthesized by a sol-gel process using metal oxides and boric acid as starting materials and citric acid as chelating agent. The main factors affecting the structure and luminescence properties of the product, such as sintering temperature, chemical composition, and Eu3+ doping concentration, were investigated. X-ray diffraction (XRD) analysis indicated that the phosphors begin to crystallize at sintering temperature of 700°C and become phase pure at 900°C. The average size of the phosphor particles after sintering at 1000°C was determined to be about 30 nm to 50 nm. The (Y,Gd)BO3:Eu3+ phosphors were found to exhibit strong red emission at 611 nm and 625 nm corresponding to the 5D0-7F2 transitions of Eu3+ in the host lattice. The photoluminescence intensity was enhanced by posttreatment at 900°C and remained unchanged at 1000°C. It was also found that the optimal concentration of Gd3+ ions for Eu3+ emission was 35%, and no concentration quenching of the photoluminescence was observed even at Eu3+ doping concentration up to 30%.

Baseline sediment trace metals investigation: Steinhatchee River estuary, Florida, Northeast Gulf of Mexico

USGS Publications Warehouse

Trimble, C.A.; Hoenstine, R.W.; Highley, A.B.; Donoghue, J.F.; Ragland, P.C.

1999-01-01

This Florida Geological Survey/U.S. Department of the Interior, Minerals Management Service Cooperative Study provides baseline data for major and trace metal concentrations in the sediments of the Steinhatchee River estuary. These data are intended to provide a benchmark for comparison with future metal concentration data measurements. The Steinhatchee River estuary is a relatively pristine bay located within the Big Bend Wildlife Management Area on the North Central Florida Gulf of Mexico coastline. The river flows 55 km through woodlands and planted pines before emptying into the Gulf at Deadman Harbor. Water quality in the estuary is excellent at present. There is minimal development within the watershed. The estuary is part of an extensive system of marshes that formed along the Florida Gulf coast during the Holocene marine transgression. Sediment accretion rate measurements range from 1.4 to 4.1 mm/yr on the basis of lead-210 measurements. Seventy-nine short cores were collected from 66 sample locations, representing four lithofacies: clay- and organic-rich sands, organic-rich sands, clean quartz sands, and oyster bioherms. Samples were analyzed for texture, total organic matter, total carbon, total nitrogen, clay mineralogy, and major and trace-metal content. Following these analyses, metal concentrations were normalized against geochemical reference elements (aluminum and iron) and against total weight percent organic matter. Metals were also normalized granulometrically against total weight percent fines (<0.062 mm). Concentrations were determined by inductively coupled plasma-atomic emission spectrometry (ICP-AES) for all metals except mercury. Mercury concentrations were determined by cold-flameless atomic absorption spectrometry (AAS). Granulometric measurements were made by sieve and pipette analyses. Organic matter was determined by two methods: weight loss upon ignition and elemental analysis (by Carlo-Erba Furnace) of carbon and nitrogen. X-ray diffraction was used to determine clay mineralogy. Trace-metal concentrations were best correlated when normalized with respect to sediment aluminum concentrations. Normalizations indicate that most major and trace-metal concentrations fall within 95% prediction limits of the expected value. This finding suggests that little significant metal contamination occurred within this system prior to 1994 sediment sampling. Exceptions include lead, mercury, copper, zinc, potassium, and phosphorous. Lead and mercury are elements that generally enter this watershed through atmospheric deposition; thus, anomalous levels of these metals are not necessarily associated with activities within the watershed of the Steinhatchee River estuary. Anomalous concentrations of other metals such as zinc, copper, and phosphorous probably do originate within the Steinhatchee watershed. Copper failed to correlate well with any geochemical or granulometric normalizer, and this condition was not limited to a single facies or area within the estuary. This finding may indicate copper contamination in the system. Increased zinc and copper levels may be attributed to marine paints. Phosphorous levels also appeared to be elevated in a few locations in the two marsh facies sampled. This may be due to nutrient loading from two small communities, Jena and Steinhatchee, or from the application of this element in fertilizer to reduce moisture stress to young planted pines on tree farms within the watershed.The Florida Geological Survey/US Department of the Interior, Minerals Management Service Cooperative Study provides baseline data for major and trace metal concentrations in the sediments of the Steinhatchee River estuary. The data are intended to provide a benchmark for comparison with metal concentration data measurements. Seventy nine short cores were collected from 66 sample locations and analyzed. Metal concentrations were normalized against geochemical reference elements and against total weight percen

Synthesis, structure, and luminescence properties of SrSiAl2O3N2:Eu(2+) phosphors for light-emitting devices and field emission displays.

PubMed

Wang, Xicheng; Zhao, Zhengyan; Wu, Quansheng; Li, Yanyan; Wang, Chuang; Mao, Aijun; Wang, Yuhua

2015-06-28

A series of SrSiAl2O3N2:Eu(2+) (0.005 ≤x≤ 0.05) phosphors were successfully synthesized through a pressureless, facile, and efficient solid state route. The crystal structure, band structure, and their photoluminescence and cathodoluminescence properties were investigated in detail. The phosphors exhibit rod shape morphology with a uniform Eu(2+) distribution. Under n-UV excitation the emission spectra shift from 477 to 497 nm with an increase of Eu(2+) concentration. The concentration quenching mechanism of Eu(2+) emission was dominated by the dipole-dipole interaction. The thermal stability is comparable to that of the commercial Ba2SiO4:Eu(2+) phosphor. The phosphor also exhibits high current saturation and high resistance under low voltage electron bombardment. All the results indicate that the SrSiAl2O3N2:Eu(2+) phosphors can be considered as candidates for application in both white LEDs and FEDs.

Sediment and Total Phosphorous Contributors in Rock River Watershed

EPA Science Inventory

Total phosphorous (TP) and total suspended sediment (TSS) pollution is a problem in the US Midwest and is of particular concern in the Great Lakes region where many water bodies are already eutrophic. Increases in monoculture corn planting to feed ethanol based biofuel productio...

Variations of physicochemical properties in Kalpakkam coastal waters, east coast of India, during southwest to northeast monsoon transition period.

PubMed

Satpathy, Kamala Kanta; Mohanty, Ajit K; Sahu, Gouri; Sarkar, Santosh K; Natesan, Usha; Venkatesan, R; Prasad, M V R

2010-12-01

A significant variation in physicochemical properties of the Kalpakkam coastal waters, eastern part of India, was observed during the event of southwest to northeast monsoon transition. Increase in nitrate, total nitrogen, and silicate concentrations were noticed during post-transition period. Ammonia concentration was at peak during transition period as compared to pre- and post-transition periods. Hypo-saline condition (~23 psu) was observed during post-transition as the surface water salinity decreased by ~10 psu from the pre-transitional values. Turbidity, suspended particulate matter, phosphate and total phosphorous values decreased marginally, coinciding with northward to southward current reversal. A drastic decrease (eightfold) in chlorophyll-a concentration was observed in the coastal water during post-transition period.

Thermoluminescence glow curve analysis and CGCD method for erbium doped CaZrO{sub 3} phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tiwari, Ratnesh, E-mail: 31rati@gmail.com; Chopra, Seema

2016-05-06

The manuscript report the synthesis, thermoluminescence study at fixed concentration of Er{sup 3+} (1 mol%) doped CaZrO{sub 3} phosphor. The phosphors were prepared by modified solid state reaction method. The powder sample was characterized by thermoluminescence (TL) glow curve analysis. In TL glow curve the optimized concentration in 1mol% for UV irradiated sample. The kinetic parameters were calculated by computerized glow curve deconvolution (CGCD) techniaue. Trapping parameters gives the information of dosimetry loss in prepared phosphor and its usability in environmental monitoring and for personal monitoring. CGCD is the advance tool for analysis of complicated TL glow curves.

Super-bright and short-lived photoluminescence of textured Zn2SiO4:Mn2+ phosphor film on quartz glass

NASA Astrophysics Data System (ADS)

Park, Jehong; Park, Kwangwon; Lee, Jaebum; Kim, Jongsu; Seo, Kwangil; Kwon, Kevin; Kung, Patrick; Kim, Seongsin M.

2010-02-01

Green-emissive textured Zn2SiO4:Mn2+ phosphor film was fabricated by a thermal diffusion of ZnO:Mn on quartz glass. The characterization has been performed in terms of Mn2+ ions concentration (Mn/Zn=1~9 mol %). As an increase of Mn2+ ions concentration in the Zn2SiO4:Mn2+ phosphor film, the emission peak was red shifted from 519 nm to 526 nm, and the decay time to 10% of the maximum intensity was shorter from 20 ms to 0.5 ms. All annealed Zn2SiO4:Mn2+ phosphor films became textured along some hexagonal directions on the amorphous quartz glass. The brightest Zn2SiO4:Mn2+ film at optimal Mn2+ concentration of 5 % showed the photoluminescence brightness of 65 % and the shortened decay time of 4.4 ms in comparison with a commercially Zn2SiO4: Mn2+ powder phosphor screen. The excellencies can be attributed to a unique textured structure.

Limnological characterization of freshwater systems of the Thomas Point Oasis (Admiralty Bay, King George Island, West Antarctica)

NASA Astrophysics Data System (ADS)

Nędzarek, Arkadiusz; Pociecha, Agnieszka

2010-12-01

Hydrochemical research into the small, shallow water bodies and wetland areas around the Henryk Arctowski Polish Antarctic Station (King George Island) is presented. Concentrations of nitrite, nitrate, ammonium, and total nitrogen in these waters were determined, as were those of reactive and total phosphorous, inorganic carbon, organic carbon, total carbon, silicate, and chloride and sulfate ions. Conductivity and pH were also measured. Average concentrations ranged widely, e.g., total nitrogen 0.176-29.21 mg L -1, total phosphorus 0.022-18.35 mg L -1, total carbon 1.38-26.90 mg L -1, Cl - 30.17-850 mg L -1, and SO 42- 2.11-236 mg L -1. The trophic status was influenced by influxes of nitrogen and phosphorus from penguin rookeries. Selected water bodies supported 31 taxa of algae and 11 invertebrate taxa, with Euglenophyta dominating in waters with high concentrations of ammonium-nitrogen, whereas diatoms characterized Lake Wujka, with low ammonium concentrations. All water bodies studied had rotifers, but crustaceans were only represented in Lake Wujka.

Enhanced photoluminescence of SrWO{sub 4}:Eu{sup 3+} red phosphor synthesized by mechanochemically assisted solid state metathesis reaction method at room temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peter, Anthuvan John, E-mail: quantajohn@gmail.com; Banu, I. B. Shameem

2015-06-24

Optically efficient europium activated alkaline earth metal tungstate nano phosphor (SrWO{sub 4}) with different doping concentrations have been synthesized by mechanochemically assisted solid state metathesis reaction at room temperature for the first time. The XRD and Raman spectra results indicated that the prepared powders exhibit a scheelite-type tetragonal structure. FTIR spectra exhibited a high absorption band situated at around 854 cm{sup −1}, which was ascribed to the W–O antisymmetric stretching vibrations into the [WO{sub 4}]{sup 2−} tetrahedron groups. Analysis of the emission spectra with different Eu{sup 3+} concentrations revealed that the optimum dopant concentration for SrWO{sub 4}: x Eu{sup 3+} phosphormore » is about 8 mol% of Eu{sup 3+}.The red emission intensity of the SSM prepared SrWO{sub 4}: 0.08Eu{sup 3+} phosphors are 2 times greater than that of the commercial Y{sub 2}O{sub 2}S: Eu{sup 3+} red phosphor prepared by the conventional solid state reaction method. All the results indicate that the phosphor is a promising red phosphor pumped by NUV InGaN chip for fabricating WLED.« less

Enhanced emission of encaged-OH--free Ca12(1-x)Sr12xAl14O33:0.1%Gd3+ conductive phosphors via tuning the encaged-electron concentration for low-voltage FEDs.

PubMed

Zhang, Meng; Liu, Yuxue; Yang, Jian; Zhu, Hancheng; Yan, Duanting; Zhang, Xinyang; Liu, Chunguang; Xu, Changshan; Zhang, Hong

2017-05-24

Encaged-OH - -free Ca 12(1-x) Sr 12x Al 14 O 33 :0.1%Gd 3+ conductive phosphors were prepared through a melt-solidification process in combination with a subsequent heat treatment. Absorption spectra showed that the maximum encaged-electron concentration was increased to 1.08 × 10 21 cm -3 through optimizing the doping amount of Sr 2+ (x = 0.005). Meanwhile, FTIR and Raman spectra indicated that pure Ca 11.94 Sr 0.06 Al 14 O 33 :0.1%Gd 3+ conductive phosphor without encaged OH - and C 2 2- anions was acquired. For the conductive powders heat-treated in air for different times, the encaged-electron concentrations were tuned from 1.02 × 10 21 to 8.3 × 10 20 cm -3 . ESR, photoluminescence, and luminescence kinetics analyses indicated that the emission at 312 nm mainly originated from Gd 3+ ions surrounded by encaged O 2- anions, while Gd 3+ ions surrounded by encaged electrons had a negative contribution to the UV emission due to the existence of an energy transfer process. Under low-voltage electron-beam excitation (3 kV), enhanced cathodoluminescence (CL) of the conductive phosphors could be achieved by tuning the encaged-electron concentrations. In particular, for the encaged-OH - -free conductive phosphor, the emission intensity of the CL was about one order of magnitude higher than that of the conductive phosphor containing encaged OH - anions. Our results suggested that the encaged-OH - -free conductive phosphors have potential application in low-voltage FEDs.

Luminescence concentration quenching and site-occupancy of Eu2+ ions in Na2Ca2Si3O9 phosphors derived from 45S5 glass-ceramics

NASA Astrophysics Data System (ADS)

Zhu, Yangguang; Tong, Chao; Xu, Chuanyan; Li, Yadong; Seo, Hyo Jin

2016-04-01

The phosphors of Na2Ca2-2xEu2xSi3O9 (x = 0, 0.03, 0.05, 0.07, 0.09) were first synthesized by sol-gel method. The crystal phase formations of the phosphors were detected by X-ray powder diffraction (XRD) measurements and the structure refinement. The photoluminescence spectra, the concentration quenching, the luminescence decay curves and the luminescence color chromaticity were measured, respectively. The excitation spectra indicate that the phosphors can be effectively excited by near UV-LED chips. Two kinds of Eu2+ sites centered at 545 nm and 505 nm were discussed by analyzing the spectra, concentration-dependent luminescence intensity and lifetimes. This is a potential tool for monitoring the bioactivity of 45S5 glass-ceramics in situ.

A novel optical ozone sensor based on purely organic phosphor.

PubMed

Lee, Dongwook; Jung, Jaehun; Bilby, David; Kwon, Min Sang; Yun, Jaesook; Kim, Jinsang

2015-02-11

An optical ozone sensor was developed based on the finding that a purely organic phosphor linearly loses its phosphorescence emission intensity in the presence of varying concentration of ozone gas and ozonated water. Compared to conventional conductance-based inorganic sensors, our novel sensory film has many advantages such as easy fabrication, low-cost, and portability. NMR data confirmed that phosphorescence drop is attributed to oxidation of the core triplet generating aldehyde group of the phosphor. We observed that linear correlation between phosphorescence and ozone concentration and it can detect ozone concentrations of 0.1 ppm that is the threshold concentration harmful to human tissue and respiratory organs. Like a litmus paper, this ozone sensor can be fabricated as a free-standing and disposable film.

Photoluminescence properties of NaPbB{sub 5}O{sub 9}:Dy{sup 3+} new material for white light applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajesh, D., E-mail: ratnakaramsvu@gmail.com; Ratnakaram, Y. C., E-mail: ratnakaramsvu@gmail.com

2014-04-24

Keeping in view of the recent increased interest towards phosphor materials and its applications, an attempt has been made in the present paper to analyze the new NaPbB{sub 5}O{sub 9}:Dy{sub 3+} phosphor with different Dy{sub 3+} concentrations. Special attention is paid to investigate their crystal structure, morphology and luminescence properties. X-ray diffraction (XRD) results confirm the formation of NaPbB{sub 5}O{sub 9}:Dy{sub 3+} phosphor powder. The scanning electron microscope (SEM) images show that the grains are in micrometer range. Photoluminescence spectra are recorded with different excitation wavelengths for the investigated phosphor and analyzed the variation of intensity of emission bands withmore » Dy{sub 3+} ion concentration. Color co-ordinates are calculated and are used to characterize the color of the phosphor.« less

Fog and Phosphorous:Mist Connections?

NASA Astrophysics Data System (ADS)

Weathers, K. C.; Caraco, N. F.; Ewing, H. A.

2005-12-01

Fog (or cloud) is an important vector for delivering water, nutrients and pollutants to many coastal and montane ecosystems worldwide. Previous research has demonstrated that elements and ions whose sources are thought to be atmospheric, such as nitrogen and sulfur, can be deposited in substantial quantities via fog water deposition. However, the ecologically-important nutrient, phosphorous (P), is thought to derive primarily from guano or terrestrial sources; it has not been demonstrated to be deposited in significant quantities via rain water, for example. Here we suggest that phosphorous may be quite prevalent in fog water and that the atmospheric deposition of phosphorous to the forest floor is significant. Phosphate appears to be either immobilized or utilized in the forest floor. We examine the concentrations of phosphorous in fog water from several ecosystems in the Americas and the spatial patterns of P movement in a fog-dominated, redwood forest in Sonoma County, CA. Phosphate concentrations were surprisingly high, ranging from 0.002 to 2.9 mg/L, in fog samples from near-coast and montane ecosystems. Phosphate in fog water appears to be derived from a crustal source as demonstrated by the strong relationship between phosphorous concentrations in fog and K:Na ratios. Fog water phosphorous inputs to the forest floor were observed to decline exponentially and vary significantly from edge to interior in a redwood forest. Phosphate via fog deposition can be detected in shallow soil zones but not at greater depths, and only at the forest edge, during the summer fog season.

A water-quality assessment of the Burnham Creek Watershed, Polk County, Minnesota

USGS Publications Warehouse

Have, M.R.

1975-01-01

A water-quality assessment of the Burnham Creek watershed, Polk County, Minn., was made in May 1975. Surface waters were calcium magnesium bicarbonate types with 0.11 mg/liter or less of nitrite plus nitrate nitrogen and 0.10 mg/liter or less of total phosphorous. Fecal coliform bacteria concentrations were between 3 and 720 colonies per 100 milliliters and fecal Streptococci concentrations ranged between 19 and 1600 colonies per 100 milliliters. Pesticide concentrations were low in the stream bottom materials, but an increasing trend was apparent in the downstream direction. The benthic community was dominated by blackfly larvae.

Quantifying phosphoric acid in high-temperature polymer electrolyte fuel cell components by X-ray tomographic microscopy.

PubMed

Eberhardt, S H; Marone, F; Stampanoni, M; Büchi, F N; Schmidt, T J

2014-11-01

Synchrotron-based X-ray tomographic microscopy is investigated for imaging the local distribution and concentration of phosphoric acid in high-temperature polymer electrolyte fuel cells. Phosphoric acid fills the pores of the macro- and microporous fuel cell components. Its concentration in the fuel cell varies over a wide range (40-100 wt% H3PO4). This renders the quantification and concentration determination challenging. The problem is solved by using propagation-based phase contrast imaging and a referencing method. Fuel cell components with known acid concentrations were used to correlate greyscale values and acid concentrations. Thus calibration curves were established for the gas diffusion layer, catalyst layer and membrane in a non-operating fuel cell. The non-destructive imaging methodology was verified by comparing image-based values for acid content and concentration in the gas diffusion layer with those from chemical analysis.

Physical Limitations of Phosphor layer thickness and concentration for White LEDs.

PubMed

Tan, Cher Ming; Singh, Preetpal; Zhao, Wenyu; Kuo, Hao-Chung

2018-02-05

Increasing phosphor layer thickness and concentration can enhance the lumen flux of white LED (W-LED). In this work, we found that increasing the phosphor layer thickness and concentration can increase its temperature, and there is also a maximum thickness and concentration beyond which their increase will not lead to lumen increase, but only temperature increase. Higher thickness and higher concentration also results in warm light instead of White light. The maximum thickness and concentration are found to be limited by the scattering of light rays with higher % decrease of blue light rays than the yellow light rays. The results obtained in this work can also be used to compute the temperature and thermo-mechanical stress distribution of an encapsulated LED, demonstrating its usefulness to the design of encapsulated LED packages. Simulation software like ANSYS and TracePro are used extensively to verify the root cause mechanisms.

Optical properties of Dy3+ and Eu3+ -Codoped SrWO4 phosphors for white light-emitting diodes

NASA Astrophysics Data System (ADS)

Cho, Shinho

2018-01-01

Dy3+ - and Eu3+ -codoped SrWO4 phosphor powders were prepared using a solid-state reaction technique by changing the molar concentration of Eu3+ within the range of 0 to 15 mol% at a fixed Dy3+ concentration of 5 mol%. The effects of Dy3+ and Eu3+ doping on the structural, morphological, and optical properties of SrWO4:Dy3+, Eu3+ phosphors were investigated via Xray diffraction, scanning electron microscopy, and photoluminescence spectrophotometry, respectively. Irrespective of the concentrations of Dy3+ and Eu3+ ions, the crystal structures of all the phosphors were tetragonal, and the grains exhibited a tendency to agglomerate. The emission spectra of Sr0.925WO4:5 mol% Dy3+ contained an intense yellow band at 573 nm arising from the 4 F 9/2 → 6 H 13/2 electric dipole transition of Dy3+, as well as three weak emission lines. When the Eu3+ ions were incorporated into the SrWO4:Dy3+ phosphors, a strong red emission peak at 615 nm originating from the 5D0 → 7F2 transition of Eu3+ appeared in addition to the four emission bands centered at 481, 573, 662, and 750 nm, which result from the 4 f-4 f transitions of Dy3+. The emission intensity decreased as the Eu3+ concentration increased up to 15 mol% due to concentration quenching, which resulted from dipole-dipole interactions. The results suggest that the color emissions and intensities of SrWO4:Dy3+, Eu3+ phosphors can be tuned from yellow to white to red by varying the types of ions used and the ratio of Dy3+ to Eu3+ ions.

Photoluminescence studies of high-efficient red-emitting K{sub 2}Y(WO{sub 4})(PO{sub 4}):Eu{sup 3+} phosphor for NUV LED

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xinguo; State Key Laboratory of Optoelectronic Materials and Technologies, School of Chemistry and Chemical Engineering, Sun Yat-Sen University, Guangzhou 510275; Chen, Mengyang

Highlights: • Novel K{sub 2}Y(WO{sub 4})(PO{sub 4}):Eu{sup 3+} red phosphors were prepared by solid-state method. • Phosphors exhibit strong red light under NUV excitation with quantum efficiency of 70.5 %. • Judd–Ofelt analysis ascertains the presence of Eu{sup 3+} in a highly asymmetric environment. • The red LED prototype was fabricated with KYWP:Eu{sup 3+} phosphor and InGaN chip. - Abstract: A series of high-efficient red-emitting phosphors K{sub 2}Y(WO{sub 4})(PO{sub 4}):Eu{sup 3+} have been successfully synthesized by conventional solid-state reaction, and its photoluminescence (PL) properties have been investigated. The phosphors can be excited efficiently by NUV light, then exhibit strong redmore » emission with quantum efficiency of 70.5%. The concentration quenching takes place at relatively high concentration of Eu{sup 3+} (x = 0.70), which is further confirmed by the variation of decay curves of the entitled phosphors. Judd–Ofelt analysis ascertains the presence of Eu{sup 3+} in a highly asymmetric environment. The phosphor exhibits good thermal stability (92.5% at 100 °C and 84.1% at 180 °C). The red LED prototype fabricated by opyimized-composition K{sub 2}Y(WO{sub 4})(PO{sub 4}):0.70Eu{sup 3+} phosphor and 395 nm-emitting InGaN chips exhibit bright red emission. The results indicate that the K{sub 2}Y(WO{sub 4})(PO{sub 4}):Eu{sup 3+} phosphors are promising red phosphors for NUV LED.« less

Analysis of serum and cerebrospinal fluid in clinically normal adult miniature donkeys.

PubMed

Mozaffari, A A; Samadieh, H

2013-09-01

To establish reference intervals for serum and cerebrospinal fluid (CSF) parameters in clinically healthy adult miniature donkeys. Experiments were conducted on 10 female and 10 male clinically normal adult miniature donkeys, randomly selected from five herds. Lumbosacral CSF collection was performed with the sedated donkey in the standing position. Cell analysis was performed immediately after the samples were collected. Blood samples were obtained from the jugular vein immediately after CSF sample collection. Sodium, potassium, glucose, urea nitrogen, total protein, calcium, chloride, phosphorous and magnesium concentrations were measured in CSF and serum samples. A paired t-test was used to compare mean values between female and male donkeys. The CSF was uniformly clear, colourless and free from flocculent material, with a specific gravity of 1.002. The range of total nucleated cell counts was 2-4 cells/μL. The differential white cell count comprised only small lymphocytes. No erythrocytes or polymorphonuclear cells were observed on cytological examination. Reference values were obtained for biochemical analysis of serum and CSF. Gender had no effect on any variables measured in serum or CSF (p>0.05). CSF analysis can provide important information in addition to that gained by clinical examination. CSF analysis has not previously been performed in miniature donkeys; this is the first report on the subject. In the present study, reference intervals for total nucleated cell count, total protein, glucose, urea nitrogen, sodium, potassium, chloride, calcium, phosphorous and magnesium concentrations of serum and CSF were determined for male and female miniature donkeys.

High Resolution Spectrometry of Leaf and Canopy Chemistry for Biochemical Cycling

NASA Technical Reports Server (NTRS)

Spanner, M. A.; Peterson, D. L.; Acevedo, W.; Matson, P.

1985-01-01

High-resolution laboratory spectrophotometer and Airborne Imaging Spectrometer (AIS) data were used to analyze forest leaf and canopy chemistry. Fundamental stretching frequencies of organic bonds in the visible, near infrared and short-wave infrared are indicative of concentrations and total content of nitrogen, phosphorous, starch and sugar. Laboratory spectrophotometer measurements showed very strong negative correlations with nitrogen (measured using wet chemistry) in the visible wavelengths. Strong correlations with green wet canopy weight in the atmospheric water absorption windows were observed in the AIS data. A fairly strong negative correlation between the AIS data at 1500 nm and total nitrogen and nitrogen concentration was evident. This relationship corresponds very closely to protein absorption features near 1500 nm.

Synthesis and Luminescence Characteristics of Cr 3+ doped Y 3Al 5O 12 Phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Brenda A.; Dabestani, Reza T.; Lewis, Linda A.

2015-10-01

Luminescence performance of yttrium aluminum garnet (Y 3Al 5O 12) phosphors as a function of Cr 3+ concentration has been investigated via two different wet-chemical synthesis techniques, direct- (DP) and hydrothermal-precipitation (HP). Using either of these methods, the red-emitting phosphor [Y 3Al 5-xCr xO 12 (YAG: Cr 3+)] showed similar photoluminescence (PL) intensities once the dopant concentration was optimized. Specifically, the YAG: Cr 3+ PL emission intensity reached a maximum at Cr3+ concentrations of x = 0.02 (0.4 at.%) and x = 0.13 (2.6 at.%) for DP and HP processed samples, respectively. The results indicated the strong influence of themore » processing method on the optimized YAG: Cr 3+ performance, where a more effective energy transfer rate between a pair of Cr3+ activators at low concentration levels was observed by using the DP synthesis technique. Development of a highly efficient phosphor, using a facile synthesis approach, could significantly benefit consumer and industrial applications by improving the operational efficiency of a wide range of practical devices.« less

TL-OSL study of Li{sub 3}PO{sub 4}: Mg, Cu phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahangdale, S. R., E-mail: sachin.rahangdale1@gmail.com; Wankhede, S. P.; Dhabekar, B. S.

In the present work, we report the thermoluminescence and optically stimulated luminescence properties of Mg and Cu doped Li{sub 3}PO{sub 4} phosphor. The phosphor was synthesized by precipitation method. The thermoluminescence dosimetric peak temperature for the phosphor varies with concentrations of Mg and Cu. Li{sub 3}PO{sub 4} shows good response to 470nm optical stimulation. The OSL sensitivity of the phosphor is approximately 12 times than that of standard Lithium magnesium phosphate. This study may help to develop this material for the application in real time dosimetry using optically stimulated luminescence.

TL-OSL study of Li3PO4: Mg, Cu phosphor

NASA Astrophysics Data System (ADS)

Rahangdale, S. R.; Wankhede, S. P.; Dhabekar, B. S.; Palikundwar, U. A.; Moharil, S. V.

2015-08-01

In the present work, we report the thermoluminescence and optically stimulated luminescence properties of Mg and Cu doped Li3PO4 phosphor. The phosphor was synthesized by precipitation method. The thermoluminescence dosimetric peak temperature for the phosphor varies with concentrations of Mg and Cu. Li3PO4 shows good response to 470nm optical stimulation. The OSL sensitivity of the phosphor is approximately 12 times than that of standard Lithium magnesium phosphate. This study may help to develop this material for the application in real time dosimetry using optically stimulated luminescence.

Influencing of various phosphor parameters on the LED performance

NASA Astrophysics Data System (ADS)

Wu, Yi Ping; Zhang, Shu Qin; Jin, Shang-zhong; Shi, Chang Shou; Li, Liang; Yu, RenYong

2012-10-01

In this paper ,the advantages and disadvantages of the methods to achieve White LED are reviewed, and phosphor-converted white LEDs are discussed in detail. In the case of blue chip exciting YAG phosphor to get white LED, use Mie scattering theory to construct physical model, then analyze how the package, concentration, thickness and particle size of phosphor work on extraction efficiency, spatial Chroma uniformity and color temperature of white LED. The conclusion of this paper advances the application of LED solid-state light source. In the end, the paper puts forward the direction and focus of phosphor research.

Temporal trends and spatial patterns in nutrient export along the Mississippi River and its Tributaries

NASA Astrophysics Data System (ADS)

Stewart, B.; Li, L.

2017-12-01

The Mississippi River, the largest river in the U. S., exports excessive nutrients from the land to the sea, causing the problem of hypoxia in the Gulf of Mexico. In this research, we examined nutrient export along the Mississippi River and its tributaries to understand its trends and patterns and to identify the major factors contributing to these trends. We examined nutrient data from 1950 - 2017 for four sites along the Mississippi River and four tributary sites from the U. S. Geological Survey. The species included: total nitrogen, organic nitrogen, ammonia, nitrate, orthophosphate, and phosphorous. We analyzed the power law relationship of concentration and discharge, for which the export of nutrient species exhibited several trends. Both nitrogen (N) and phosphorous (P) species exhibited mostly chemodynamic behavior. This is in contrast to previous observations in smaller agricultural land where N and P export was mostly chemostatic with no significant change in concentration as discharge varies, suggesting possible scaling effects at different spatial scales. We also compared the average annual concentration over time at each site. The N concentration decreased from upstream to downstream, likely due to greater agricultural activities in the upstream Mississippi river and possible denitrification along the river. The N concentration also increased with time. The P species, however, fluctuated from site to site with no clear spatial patterns, but consistently exhibited higher concentrations at upstream sites with greater agricultural activities. The P species also fluctuated over time, likely due to patterns in discharge and agricultural activities. The results of this research can be further explored by calculating the total export of nutrients into the Gulf of Mexico to determine limits and drivers of nutrient export for better water management, thus helping prevent hypoxia and eutrophication within the Mississippi River basin.

A combined time-of-flight and depth-of-interaction detector for total-body positron emission tomography.

PubMed

Berg, Eric; Roncali, Emilie; Kapusta, Maciej; Du, Junwei; Cherry, Simon R

2016-02-01

In support of a project to build a total-body PET scanner with an axial field-of-view of 2 m, the authors are developing simple, cost-effective block detectors with combined time-of-flight (TOF) and depth-of-interaction (DOI) capabilities. This work focuses on investigating the potential of phosphor-coated crystals with conventional PMT-based block detector readout to provide DOI information while preserving timing resolution. The authors explored a variety of phosphor-coating configurations with single crystals and crystal arrays. Several pulse shape discrimination techniques were investigated, including decay time, delayed charge integration (DCI), and average signal shapes. Pulse shape discrimination based on DCI provided the lowest DOI positioning error: 2 mm DOI positioning error was obtained with single phosphor-coated crystals while 3-3.5 mm DOI error was measured with the block detector module. Minimal timing resolution degradation was observed with single phosphor-coated crystals compared to uncoated crystals, and a timing resolution of 442 ps was obtained with phosphor-coated crystals in the block detector compared to 404 ps without phosphor coating. Flood maps showed a slight degradation in crystal resolvability with phosphor-coated crystals; however, all crystals could be resolved. Energy resolution was degraded by 3%-7% with phosphor-coated crystals compared to uncoated crystals. These results demonstrate the feasibility of obtaining TOF-DOI capabilities with simple block detector readout using phosphor-coated crystals.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, Yaoqing; School of Materials Science and Engineering, Shanghai Institute of Technology, Shanghai 201418; Zhang, Qinghong

A new silicate garnet phosphor, Lu{sub 2−x}CaMg{sub 2}Si{sub 2.9}Ti{sub 0.1}O{sub 12}:xCe was synthesized by a high temperature solid-state reaction under reductive atmosphere. X-ray diffraction (XRD) showed that the powder was pure garnet phase. The emission and excitation spectrum indicated that the Lu{sub 2−x}CaMg{sub 2}Si{sub 2.9}Ti{sub 0.1}O{sub 12}:xCe phosphors could absorb blue light in the spectral range of 400–550 nm efficiently and exhibit bright yellow–orange emission in the range of 520–750 nm. With the increase of Ce{sup 3+} concentration, the emission band of Ce{sup 3+} showed a red shift. Interestingly, the concentration quenching occurred when the Ce{sup 3+} concentration exceeded 4more » mol%. The temperature-dependent luminescent properties of the phosphors were discussed and the Lu{sub 1.96}CaMg{sub 2}Si{sub 2.9}Ti{sub 0.1}O{sub 12}:0.04Ce phosphors showed good performances in color temperature (2430 K) and potential applications for warm white LEDs. - Graphical Abstract: This image shows that the phosphor of Lu{sub 1.96}CaMg{sub 2}Si{sub 2.9}Ti{sub 0.1}O{sub 12}:0.04Ce can generate a uniform yellow tint under natural light illumination and emit orange–red light when excited by blue light. With a fixed 467 nm emission light, warm white light can be produced by this phosphor, which indicates that the phosphor is potentially applicable in warm white light emitting diodes based on GaN chips. - Highlights: • A new silicate garnet phosphor was synthesized by solid-state method. • Secondary phases can be avoided when a small amount of Si{sup 4+} were replaced by Ti{sup 4+}. • A broad emission band of Ce{sup 3+} in the phosphors was described. • The phosphors are potentially applicable in warm white light emitting diodes.« less

Synthesis and luminescent properties of spindle-like CaWO{sub 4}:Sm{sup 3+} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Yue; Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026; Liu, Yu

2012-01-15

Graphical abstract: In this paper, spindle-like CaWO{sub 4}:Sm{sup 3+} phosphors were prepared via a polyvinylpyrrolidone (PVP)-assisted sonochemical process. Dependence of emission intensity on Sm{sup 3+} ions concentration in the CaWO{sub 4}:Sm{sup 3+} phosphor were also calculated via a nonlinear fitting by using the formula y = ax/(1 + bx{sup c}). Highlights: Black-Right-Pointing-Pointer The samples were prepared via a PVP assisted sonochemical process. Black-Right-Pointing-Pointer The color coordinates for 1 mol% Sm{sup 3+} doped CaWO{sub 4} phosphor were calculated. Black-Right-Pointing-Pointer The D-D interaction is responsible for concentration quenching between Sm{sup 3+} ions. Black-Right-Pointing-Pointer The critical energy transfer distances (R{sub c}) were obtained.more » -- Abstract: Spindle-like CaWO{sub 4}:Sm{sup 3+} phosphors were prepared via a Polyvinylpyrrolidone (PVP)-assisted sonochemical process, and characterized by using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and photoluminescence spectroscopy (PL). The XRD results suggested that the prepared samples are single-phase. The FE-SEM images indicated that the prepared CaWO{sub 4}:Sm{sup 3+} phosphors are composed of many spindles with maximum average diameter of 150 nm and maximum average length of 500 nm. Under 404 nm excitation, the characteristic emissions corresponding to {sup 4}G{sub 5/2} {yields} {sup 6}H{sub J} (J = 5/2, 7/2, 9/2 and 11/2) transitions of Sm{sup 3+} in CaWO{sub 4} phosphors were observed. The color coordinates for 1 mol% Sm{sup 3+} doped CaWO{sub 4} phosphor were calculated to be (0.595, 0.404). The fluorescent concentration quenching of Sm{sup 3+} doped spindle-like phosphors was studied based on the Van Uitert's model, and it was found that the electric dipole-dipole (D-D) interaction is the dominant energy transfer mechanism between Sm{sup 3+} ions in the CaWO{sub 4}:Sm{sup 3+} phosphors. The critical energy transfer distance was estimated.« less

Polymer Based Thin Film Screen Preparation Technique

NASA Astrophysics Data System (ADS)

Valais, I.; Michail, C.; Fountzoula, C.; Fountos, G.; Saatsakis, G.; Karabotsos, A.; Panayiotakis, G. S.; Kandarakis, I.

2017-11-01

Phosphor screens, mainly prepared by electrophoresis, demonstrate brightness equal to the standard sedimentation on glass or quartz substrate process and are capable of very high resolution. Nevertheless, they are very fragile, the shape of the screen is limited to the substrate shape and in order to achieve adequate surface density for application in medical imaging, a significant quantity of the phosphor will be lost. Fluorescent films prepared by the dispersion of phosphor particles into a polymer matrix could solve the above disadvantages. The aim of this study is to enhance the stability of phosphor screens via the incorporation of phosphor particles into a PMMA (PolyMethyl MethAcrylate) matrix. PMMA is widely used as a plastic optical fiber, it shows almost nearly no dispersion effects and it is transparent in the whole visible spectral range. Different concentrations of PMMA in MMA (Methyl Methacrylate) were examined and a 37.5 % w/w solution was used for the preparation of the thin polymer film, since optical quality characteristics were found to depend on PMMA in MMA concentration. Scanning Electron Microscopy (SEM) images of the polymer screens demonstrated high packing density and uniform distribution of the phosphor particles. This method could be potentially used for phosphor screen preparation of any size and shape.

Synthesis and luminescence characterization of a new yellowish-orange phosphor: Ba2 B10 O17 :Sm3.

PubMed

Li, Jiangong; Yan, Huifang; Yan, Fengmei

2017-02-01

A new yellowish-orange emitting phosphor, Ba 2 B 10 O 17 :Sm 3 + for use as a white light-emitting diode (W-LED) was synthesized by a solid-state reaction method. The X-ray diffraction results indicated that a pure Ba 2 B 10 O 17 material was obtained. As a potential yellowish-orange luminescent material for W-LEDs, the Ba 2 B 10 O 17 :Sm 3 + phosphor could be excited effectively by near-ultraviolet (n-UV) light and exhibited yellowish-orange emission centered at 560 nm corresponding to the 4 G 5/2  →  6 H 5/2 transition of Sm 3 + ions. The optimum concentration of Sm 3 + ions in Ba 2 B 10 O 17 , critical transfer distance (Ra) and concentration quenching mechanism of the presented phosphor were investigated. Moreover, CIE chromaticity coordinates and color purity performance of the Ba 2 B 10 O 17 :Sm 3 + phosphor were also discussed. The present work suggests that the Ba 2 B 10 O 17 :Sm 3 + phosphor has potential as a type of yellowish-orange emitting phosphor. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

A potential green emitting citrate gel synthesized NaSrBO3:Tb3+ phosphor for display application

NASA Astrophysics Data System (ADS)

Bedyal, A. K.; Kumar, Vinay; Swart, H. C.

2018-04-01

A potential green emitting NaSrBO3:Tb3+ (1-9 mol%) phosphor was synthesized by a citrate gel combustion method. X-ray diffraction patterns confirmed the monoclinic phase of the phosphor. The phosphor emitted intense green emission under near-UV and electron excitation due to the characteristic transitions 5D4→7F6(488 nm),5D4→7F5(544 nm),5D4→7F4(586 nm) and 5D4→7F3(622 nm) of Tb3+ ions. The optimal molar concentration of Tb3+ ions was found to be 6 mol%, after that concentration quenching occurred. The dipole-dipole interaction was found to be accountable for energy transfer between the Tb3+ ions. X-ray photoelectron spectroscopy was carried out to analyze the chemical states of the elements and suggest that terbium was mostly presented in the (+3) valance state in the phosphor. The approximated Commission Internationale de l‧Eclairage coordinates for the PL (0.31, 0.61) and CL (0.33, 0.57) were found to be very close to the well-known green emitting phosphor. The obtained results suggest that the studied phosphor could be an ultimate choice for green emission in display applications.

Converter slag-coal cinder columns for the removal of phosphorous and other pollutants.

PubMed

Yang, Jian; Wang, Su; Lu, Zhibo; Yang, Jian; Lou, Shanjie

2009-08-30

A mixture of converter slag and coal cinder as adsorbent for the removal of phosphorous and other pollutants was studied in the paper. The maximum P adsorption capacity, pH of solution, contact time and initial phosphate concentration were evaluated in batch experiments for the two materials firstly. The data of P sorption were best fitted to Langumir equation, and the maximum adsorption capacities of converter slag and coal cinder were 2.417 and 0.398 mg P/g, respectively. The pH of solutions with converter slag and coal cinder changed dramatically with time and closed to 8 in 8h, and the influence of initial pH on phosphate removal by coal cinder was more significant than by converter slag. Phosphate removal rate by converter slag decreased with increase of initial phosphate concentrations. Subsequently, two flow-through columns (Column 1#, V(converter slag):V(coal cinder)=1:5; Column 2#, V(converter slag):V(coal cinder)=1:3) were operated for the removal of phosphorous and other pollutants from the effluents of a vermifilter for nearly eleven months. Results indicated the average removal efficiency of total phosphorus, dissolved phosphorus, COD and NH(4)(+)-N by Column 1# were 44%, 56%, 31% and 67%, and by Column 2# were 42%, 54%, 24% and 57%, respectively. Column 1# had higher removal efficiency for P and other pollutants.

Preparation and Luminescence Properties of Ca9NaZn(PO4)7:Dy3+ Single-Phase White Light-Emitting Phosphor

NASA Astrophysics Data System (ADS)

Zhu, Daoyun; Liao, Min; Mu, Zhongfei; Wu, Fugen

2018-05-01

Dy3+-doped Ca9NaZn(PO4)7 has been synthesized by high-temperature solid-state reaction. X-ray diffraction analysis revealed that the obtained phosphors existed as single phase. Doping with Dy3+ at low concentration had no obvious effect on the crystal structure of the host. Dy3+-doped samples showed strong emission at approximately 480 nm and 571 nm under excitation at 350 nm. The blue and yellow emissions showed almost the peak intensity. The combination of blue and yellow light formed white light. The color coordinates (0.323, 0.372) of the composite light are located in the white light region. The optimum doping concentration of Dy3+ ions was experimentally determined to be 10 mol.%. The concentration quenching mechanism was ascertained to be electric dipole-dipole interaction among Dy3+ ions. The obtained phosphors exhibited good thermal stability. These results indicate potential applications as single-phase white light-emitting phosphors.

Water-quality assessment of the Trinity River Basin, Texas - Nutrients in streams draining an agricultural and an urban area, 1993-95

USGS Publications Warehouse

Land, Larry F.; Shipp, Allison A.

1996-01-01

Water samples collected from streams draining an agricultural area in the west-central part of the Trinity River Basin upstream from the Richland-Chambers Reservoir and from streams draining an urban area in the Dallas-Fort Worth metropolitan area during March 1993 - September 1995 were analyzed for nutrients (nitrogen and phosphorus compounds). A comparison of the data for agricultural and urban streams shows the maximum concentration of total nitrogen is from an urban stream and the maximum concentration of total phosphorus is from an agricultural stream. One-half of the samples have total nitrogen concentrations equal to or less than 1.1 and 1.0 milligrams per liter in the agricultural and urban streams, respectively; and one-half of the samples have total phosphorous concentrations equal to or less than 0.04 and 0.05 milligram per liter in the agricultural and urban streams, respectively. The highest concentrations of total nitrogen in both types of streams are in the spring. The minimum concentrations of total nitrogen are during the summer in the agricultural streams and during the winter in the urban streams. Concentrations of total phosphorus in agricultural streams show negligible seasonal variability. The highest concentrations of total phosphorus are in spring and possibly late summer in the urban streams. In the midrange of streamflow in the urban streams and throughout the range of streamflow in the agricultural streams, concentrations of total nitrogen increase. Concentrations of total phosphorus increase with streamflow in the middle and upper ranges of streamflow in both agricultural and urban streams.

Potential of hydrolysis of particulate COD in extended anaerobic conditions to enhance biological phosphorous removal.

PubMed

Jabari, P; Yuan, Q; Oleszkiewicz, J A

2016-11-01

The effect of anaerobic hydrolysis of particulate COD (pCOD) on biological phosphorous removal in extended anaerobic condition was investigated through (i) sequencing batch reactors (SBR)s with anaerobic hydraulic retention time (HRT) of 0.8, 2, and 4 h; (ii) batch tests using biomass from a full scale biological nutrient removal (BNR) plant; and (iii) activated sludge modeling (BioWin 4.1 simulation). The results from long-term SBRs operation showed that phosphorus removal was correlated to the ratio of filtered COD (FCOD) to total phosphorus (TP) in the influent. Under conditions with low FCOD/TP ratio (average of 20) in the influent, extending anaerobic HRT to 4 h in the presence of pCOD did not significantly improve overall phosphorous removal. During the period with high FCOD/TP ratio (average of 37) in the influent, all SBRs removed phosphorous completely, and the long anaerobic HRT did not have negative effect on overall phosphorous removal. The batch tests also showed that pCOD at different concentration during 4 h test did not affect the rate of anaerobic phosphorus release. The rate of anaerobic hydrolysis of pCOD was significantly low and extending the anaerobic HRT was ineffective. The simulation (BioWin 4.1) of SBRs with low influent FCOD/TP ratio showed that the default kinetics of anaerobic hydrolysis in ASM2d overestimated phosphorous removal in the SBRs (high anaerobic hydrolysis of pCOD). The default anaerobic hydrolysis rate in BioWin 4.1 (ten times lower) could produce similar phosphorous removal to that in the experiment. Results showed that the current kinetics of anaerobic hydrolysis in ASM2d could lead to considerable error in predicting phosphorus removal in processes with extended anaerobic HRT. Biotechnol. Bioeng. 2016;113: 2377-2385. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Photoluminescence properties and thermal stability of blue-emitting Ba5-xCl(PO4)3:xEu2+ (0.004≤x≤0.016) phosphors.

PubMed

Liu, Jie; Zhang, Zhi-Ming; Wu, Zhan-Chao; Wang, Fang-Fang; Li, Zhen-Jiang; Kuang, Shao-Ping; Wu, Ming-Mei

2017-01-15

A series of blue-emitting Ba 5-x Cl(PO 4 ) 3 :xEu 2+ (0.004≤x≤0.016) phosphors were synthesized by conventional high-temperature solid state reaction. The structure and photoluminescence (PL) properties of the phosphors were investigated. The as-prepared phosphors exhibit broad excitation band ranging from 250 to 420nm, and strong asymmetric blue emission band peaking at 436nm. The optimum concentration of Eu 2+ in the Ba 5 Cl(PO 4 ) 3 :Eu 2+ phosphor is x=0.01, and the concentration quenching mechanism is verified to be the combined actions of dipole-dipole interaction and radiation re-absorption mechanism. The thermal stability of Ba 5 Cl(PO 4 ) 3 :Eu 2+ was evaluated by temperature-dependent PL spectra. Compared with that of commercial BaMgAl 10 O 17 :Eu 2+ (BAM) phosphor, the Ba 5-x Cl(PO 4 ) 3 :xEu 2+ phosphors exhibit similarly excellent thermal quenching property. In addition, the CIE chromaticity coordinates of Ba 5-x Cl(PO 4 ) 3 :xEu 2+ (0.004≤x≤0.016) were calculated to evaluate the color quality. All the results indicate that Ba 5 Cl(PO 4 ) 3 :Eu 2+ is a promising candidate phosphor for near-ultraviolet (n-UV) pumped LED. Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis and Photoluminescence Properties of BaWO4:RE3+ (RE = Eu or Sm) Phosphors

NASA Astrophysics Data System (ADS)

Cho, Shinho

2018-04-01

BaWO4:RE3+ (RE = Eu or Sm) phosphor powders were prepared with different doping concentrations of the activator ion by using the conventional solid-state reaction method. The dependences in the crystal structure, luminescence intensity, and morphology on the Eu3+ and the Sm3+ concentrations in BaWO4 were investigated using X-ray diffraction (XRD), photoluminescence spectrophotometry, and scanning electron microscopy (SEM), respectively. XRD analysis showed tetragonal BaWO4 structures for all the phosphors synthesized, regardless of the type and the doping concentration of the activator ion. SEM images indicated that as the concentration of activator ions was increased, the crystalline particles showed an increasing tendency to agglomerate irregularly. The room temperature excitation spectra of Eu3+- or Sm3+-doped BaWO4 phosphors consisted of a broad charge transfer band in the ultraviolet region and several sharp 4 f-4 f transitions. When Eu3+-doped BaWO4 phosphors were excited at 274 nm, the emission spectra exhibited sharp bands due to inner shell transitions occurring from the excited energy state 5 D 0 to the lower energy levels 7 F J ( J = 1, 2, 3, and 4). For Sm3+-doped BaWO4 phosphors, three intense emission peaks at 568, 603, and 649 nm and a very weak line at 712 nm were observed. The highest asymmetry ratio-the intensity ratio of the 4 G 5/2 → 6 H 9/2 electric dipole to the 4 G 5/2 → 6 H 5/2 magnetic dipole transitions-was obtained for 1 mol% doping of Sm3+, indicating that the Sm3+ ions occupied the non-inversion symmetry sites.

A combined time-of-flight and depth-of-interaction detector for total-body positron emission tomography

PubMed Central

Berg, Eric; Roncali, Emilie; Kapusta, Maciej; Du, Junwei; Cherry, Simon R.

2016-01-01

Purpose: In support of a project to build a total-body PET scanner with an axial field-of-view of 2 m, the authors are developing simple, cost-effective block detectors with combined time-of-flight (TOF) and depth-of-interaction (DOI) capabilities. Methods: This work focuses on investigating the potential of phosphor-coated crystals with conventional PMT-based block detector readout to provide DOI information while preserving timing resolution. The authors explored a variety of phosphor-coating configurations with single crystals and crystal arrays. Several pulse shape discrimination techniques were investigated, including decay time, delayed charge integration (DCI), and average signal shapes. Results: Pulse shape discrimination based on DCI provided the lowest DOI positioning error: 2 mm DOI positioning error was obtained with single phosphor-coated crystals while 3–3.5 mm DOI error was measured with the block detector module. Minimal timing resolution degradation was observed with single phosphor-coated crystals compared to uncoated crystals, and a timing resolution of 442 ps was obtained with phosphor-coated crystals in the block detector compared to 404 ps without phosphor coating. Flood maps showed a slight degradation in crystal resolvability with phosphor-coated crystals; however, all crystals could be resolved. Energy resolution was degraded by 3%–7% with phosphor-coated crystals compared to uncoated crystals. Conclusions: These results demonstrate the feasibility of obtaining TOF–DOI capabilities with simple block detector readout using phosphor-coated crystals. PMID:26843254

A combined time-of-flight and depth-of-interaction detector for total-body positron emission tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berg, Eric, E-mail: eberg@ucdavis.edu; Roncali, Emilie; Du, Junwei

Purpose: In support of a project to build a total-body PET scanner with an axial field-of-view of 2 m, the authors are developing simple, cost-effective block detectors with combined time-of-flight (TOF) and depth-of-interaction (DOI) capabilities. Methods: This work focuses on investigating the potential of phosphor-coated crystals with conventional PMT-based block detector readout to provide DOI information while preserving timing resolution. The authors explored a variety of phosphor-coating configurations with single crystals and crystal arrays. Several pulse shape discrimination techniques were investigated, including decay time, delayed charge integration (DCI), and average signal shapes. Results: Pulse shape discrimination based on DCI providedmore » the lowest DOI positioning error: 2 mm DOI positioning error was obtained with single phosphor-coated crystals while 3–3.5 mm DOI error was measured with the block detector module. Minimal timing resolution degradation was observed with single phosphor-coated crystals compared to uncoated crystals, and a timing resolution of 442 ps was obtained with phosphor-coated crystals in the block detector compared to 404 ps without phosphor coating. Flood maps showed a slight degradation in crystal resolvability with phosphor-coated crystals; however, all crystals could be resolved. Energy resolution was degraded by 3%–7% with phosphor-coated crystals compared to uncoated crystals. Conclusions: These results demonstrate the feasibility of obtaining TOF–DOI capabilities with simple block detector readout using phosphor-coated crystals.« less

Synthesis and luminescent properties of CaCO3:Eu3+@SiO2 phosphors with core-shell structure

NASA Astrophysics Data System (ADS)

Liu, Min; Kang, Ming; Chen, Kexu; Mou, Yongren; Sun, Rong

2018-03-01

Integrating the processes of preparation of CaCO3:Eu3+ and its surface-coating, core-shell structured CaCO3:Eu3+@SiO2 phosphors with red emission were synthesized by the carbonation method and surface precipitation procedure using sodium silicate as silica source. The phase structure, thermal stability, morphology and luminescent property of the as-synthesized samples were characterized by X-ray diffraction, Fourier transform infrared spectrum, thermal analysis, field-emission scanning electron microscopy, transmission electron microscope and photoluminescence spectra. The experimental results show that Eu3+ ions as the luminescence center are divided into two types: one is at the surface of the CaCO3 and the other inhabits the site of Ca2+. For CaCO3:Eu3+@SiO2 phosphors, the SiO2 layers are continuously coated on the surface of CaCO3:Eu3+ and show a typical core-shell structure. After coated with SiO2 layer, the luminous intensity and the compatibility with the rubber matrix increase greatly. Additionally, the luminous intensity increases with the increasing of Eu3+ ions concentration in CaCO3 core and concentration quenching occurs when Eu3+ ions concentration exceeds 7.0 mol%, while it is 5.0 mol% for CaCO3:Eu3+ phosphors. Therefore, preparation of CaCO3:Eu3+@SiO2 phosphors can not only simplify the experimental process through integrating the preparation of CaCO3:Eu3+ and SiO2 layer, but also effectively increase the luminous intensities of CaCO3:Eu3+ phosphors. The as-obtained phosphors may have potential applications in the fields of optical materials and functional polymer composite materials, such as plastics and rubbers.

A novel greenish yellow-orange red Ba3Y4O9:Bi(3+),Eu(3+) phosphor with efficient energy transfer for UV-LEDs.

PubMed

Li, Kai; Lian, Hongzhou; Shang, Mengmeng; Lin, Jun

2015-12-21

A series of novel color-tunable Ba3Y4O9:Bi(3+),Eu(3+) phosphors were prepared for the first time via the high-temperature solid-state reaction route. The effect of Bi(3+) concentration on the emission intensity of Ba3Y4O9:Bi(3+) was investigated. The emission spectra of the Ba3Y4O9:Bi(3+),Eu(3+) phosphors present both a greenish yellow band of Bi(3+) emission centered at 523 nm, and many characteristic emission lines of Eu(3+), derived from the allowed (3)P1-(1)S0 transition of the Bi(3+) ion and the (5)D0-(7)FJ transition of the Eu(3+) ion, respectively. The energy transfer phenomenon from Bi(3+) to Eu(3+) ions is observed under UV excitation in Bi(3+), Eu(3+) co-doped Ba3Y4O9 phosphors, and their transfer mechanism is demonstrated to be a resonant type via dipole-quadrupole interaction. The critical distance between Bi(3+) and Eu(3+) for the energy transfer effect was calculated via the concentration quenching and spectral overlap methods. Results show that color tuning from greenish yellow to orange red can be realized by adjusting the mole ratio of Bi(3+) and Eu(3+) concentrations based on the principle of energy transfer. Moreover, temperature-dependent PL properties, CIE chromaticity coordinates and quantum yields of Ba3Y4O9:Bi(3+),Eu(3+) phosphors were also supplied. It is illustrated that the as-prepared Ba3Y4O9:Bi(3+),Eu(3+) phosphors can be potential candidates for color-tunable phosphors applied in UV-pumped LEDs.

Enhanced Photoluminescent Properties and Crystalline Morphology of LiBaPO4:Tm3+ Phosphor through Microwave Sintering Method

PubMed Central

Lai, Hsuan-Lin; Weng, Min-Hang; Yang, Ru-Yuan; Chang, Shoou-Jinn

2016-01-01

An investigation of the photoluminescent properties and crystalline morphology of blue emitting LiBa1−xPO4:xTm3+ phosphors with various concentrations (x = 0.005–0.030) of Tm3+ ions were synthesized by microwave sintering. For comparison, the LiBa1−xPO4:xTm3+ powders sintered at the same sintering condition but in a conventional furnace were also investigated. LiBaPO4 without second phase was formed no matter which furnace was used. More uniform grain size distributions are obtained by microwave sintering. When the concentration of Tm3+ ion was x = 0.015, the luminescence intensity reached a maximum value, and then decreased with the increases of the Tm3+ concentration due to concentration quenching effect. The microwave sintering significantly enhanced the emission intensity of LiBa1−xPO4:xTm3+ phosphors. Additionally, the d-d interaction is the key mechanism of concentration quenching for LiBaPO4:Tm3+. The chromaticity (x, y) for all LiBa1−xPO4:xTm3+ phosphors are located at (0.16, 0.05), which will be classified as a blue region. PMID:28773483

Tunable Luminescence in Sr2MgSi2O7:Tb3+, Eu3+Phosphors Based on Energy Transfer

PubMed Central

Li, Minhong; Wang, Lili; Ran, Weiguang; Deng, Zhihan; Shi, Jinsheng; Ren, Chunyan

2017-01-01

A series of Tb3+, Eu3+-doped Sr2MgSi2O7 (SMSO) phosphors were synthesized by high temperature solid-state reaction. X-ray diffraction (XRD) patterns, Rietveld refinement, photoluminescence spectra (PL), and luminescence decay curves were utilized to characterize each sample’s properties. Intense green emission due to Tb3+ 5D4→7F5 transition was observed in the Tb3+ single-doped SMSO sample, and the corresponding concentration quenching mechanism was demonstrated to be a diople-diople interaction. A wide overlap between Tb3+ emission and Eu3+ excitationspectraresults in energy transfer from Tb3+ to Eu3+. This has been demonstrated by the emission spectra and decay curves of Tb3+ in SMSO:Tb3+, Eu3+ phosphors. Energy transfer mechanism was determined to be a quadrupole-quadrupole interaction. And critical distance of energy transfer from Tb3+ to Eu3+ ions is calculated to be 6.7 Å on the basis of concentration quenching method. Moreover, white light emission was generated via adjusting concentration ratio of Tb3+ and Eu3+ in SMSO:Tb3+, Eu3+ phosphors. All the results indicate that SMSO:Tb3+, Eu3+ is a promising single-component white light emitting phosphor. PMID:28772587

The effect of Ce3+ concentration and heat treatment on the luminescence efficiency of YAG phosphor

NASA Astrophysics Data System (ADS)

Valiev, Damir; Han, Tao; Vaganov, Vitaly; Stepanov, Sergey

2018-05-01

Y3Al5O12 (YAG) phosphor powders doped with Ce3+ at different concentrations (YAG:xCe, x = 0.02, 0.04, 0.06, 0.08, 0.1 wt%) were synthesized by the solid-state reaction method with the addition of BaF2 flux. The effects of cerium concentration and heat treatment on the luminescence efficiency of the YAG:Ce3+ phosphor were investigated. The introduction of Ce3+ ions leads to an increase in luminescent intensity of the YAG phosphor at 560 nm. The band at 530 nm is attributed to Ce3+ ions (optical transitions from the 4f-5d excited state). We assumed that such an increase in the luminescent intensity is due to the ability of Ce3+ to act as a luminescence sensitizer of intrinsic defects in YAG phosphor. The analysis of luminescence decay kinetics in the investigated samples has shown that the decay time in all samples does not differ significantly and equals τ ≈ 60 ± 3 ns. We showed experimentally that increasing the luminescence intensity has an effect observed with relatively low temperature treatment (T = 400 K). The nature of possible luminescence centers and the effect of low heat treatment on the luminescence properties of the powders are discussed.

Infrared spectroscopy and upconversion luminescence behaviour of erbium doped yttrium (III) oxide phosphor

NASA Astrophysics Data System (ADS)

Dubey, Vikas; Tiwari, Ratnesh; Tamrakar, Raunak Kumar; Rathore, Gajendra Singh; Sharma, Chitrakant; Tiwari, Neha

2014-11-01

The paper reports upconversion luminescence behaviour and infra-red spectroscopic pattern of erbium doped yttrium (III) oxide phosphor. Sample was synthesized by solid state reaction method with variable concentration or erbium (0.5-2.5 mol%). The conventional solid state method is suitable for large scale production and eco-friendly method. The prepared sample was characterized by X-ray diffraction (XRD) technique. From structural analysis by XRD technique shows cubic structure of prepared sample with variable concentration of erbium and no impurity phase were found when increase the concentration of Er3+. Particle size was calculated by Scherer's formula and it varies from 67 nm to 120 nm. The surface morphology of prepared phosphor was determined by field emission gun scanning electron microscopy (FEGSEM) technique. The surface morphology of the sample shows good connectivity with grains as well as some agglomerates formation occurs in sample. The functional group analysis was done by Fourier transform infra-red technique (FTIR) analysis which confirm the formation of Y2O3:Er3+ phosphor was prepared. The results indicated that the Y2O3:Er3+ phosphors might have high upconversion efficiency because of their low vibrational energy. Under 980 nm laser excitation sample shows intense green emission at 555 nm and orange emission at 590 nm wavelength. For green emission transition occurs 2H11/2 → 4I15/2, 4S3/2 → 4I15/2 for upconversion emissions. Excited state absorption and energy transfer process were discussed as possible upconversion mechanisms. The near infrared luminescence spectra was recorded. The upconversion luminescence intensity increase with increasing the concentration or erbium up to 2 mol% after that luminescence intensity decreases due to concentration quenching occurs. Spectrophotometric determinations of peaks are evaluated by Commission Internationale de I'Eclairage (CIE) technique. From CIE technique the dominant peak of from PL spectra shows intense green emission so the prepared phosphor is may be useful for green light emitting diode (GLED) application.

A potential amber-emitting KCaVO4:Sm3+ nanophosphor for near-UV LEDs

NASA Astrophysics Data System (ADS)

Biswas, Pankaj; Kumar, Vinay

2018-05-01

The Sm3+ doped KCaVO4 phosphor powders were synthesized via combustion route. The powder X-ray diffraction (pXRD) analysis established the crystalline structure and phase of the phosphor material. Williamson-Hall technique was employed to approximate the mean grain size and lattice micro-strain. The transmission electron microscope (TEM) studies were carried out to confirm the nano-sized grain formation. On 405 nm excitation, the phosphor gave amber emission which was assigned to 4G5/2 → 6HJ/2 (J = 7/2, 9/2) transitions of the Sm3+ ion. The concentration quenching mechanism was studied and the optimum dopant concentration in the phosphor was obtained as 2.0 mol%. The diffuse reflectance (DR) studies were carried out to obtain optical band gap (Eg) and Urbach energy (Ec) of the KCaVO4 phosphor which were estimated as 3.63 eV and 98.6 meV, respectively. The color coordinates (x = 0.61, y = 0.39) of the nanophosphor signified the amber shade in the color gamut. The high luminescent properties of KCaVO4:Sm3+ phosphor suggests that the material can be explored as a potential phosphor to be profitably excited by near-UV LEDs to bridge the amber gap in light emitting diodes (LEDs) for solid state lighting (SSL) applications.

Photoluminescence studies on holmium (III) and praseodymium (III) doped calcium borophosphate (CBP) phosphors

NASA Astrophysics Data System (ADS)

Reddy Prasad, V.; Damodaraiah, S.; Devara, S. N.; Ratnakaram, Y. C.

2018-05-01

Using solid state reaction method, Ho3+ and Pr3+ doped calcium borophosphate (CBP) phosphors were prepared. These phosphors were characterized using XRD, SEM, FT-IR, 31P solid state NMR, photoluminescence (PL) and decay profiles. Structural details were discussed from XRD and FT-IR spectra. From 31P NMR spectra of these phosphors, mono-phosphate complexes Q0-(PO43-) were observed. Photoluminescence spectra were measured for both Ho3+ and Pr3+ doped calcium borophosphate phosphors and the spectra were studied for different concentrations. Decay curves were obtained for the excited level, 5F4+5S2 of Ho3+ and 1D2 level of Pr3+ in these calcium borophosphate phosphors and lifetimes were measured. CIE color chromaticity diagrams are drawn for these two rare earth ions in calcium borophosphate phosphors. Results show that Ho3+ and Pr3+ doped CBP phosphors might be served as green and red luminescence materials.

Synthesis, energy transfer and tunable emission properties of SrSb2O6:Eu3 +, Bi3 + phosphor

NASA Astrophysics Data System (ADS)

Cao, Renping; Fu, Ting; Peng, Dedong; Cao, Chunyan; Ruan, Wen; Yu, Xiaoguang

2016-12-01

Host SrSb2O6, SrSb2O6:Bi3 +, SrSb2O6:Eu3 +, and SrSb2O6:Eu3 +, Bi3 + phosphors are synthesized by solid state reaction method in air. Host SrSb2O6 with excitation 254 nm shows weak green-yellow emission in the range of 320-780 nm due to Sb5 + → O2- transition. SrSb2O6:Bi3 + phosphor with excitation 365 nm emits green light within the range 400-650 nm owing to the 3P1 → 1S0 transition of Bi3 + ion. SrSb2O6:Eu3 + phosphor with excitation 254 nm exhibits a systematically varied hue from green to orange-red light by increasing Eu3 + concentration from 0 to 7 mol%, and that with excitation 394 nm only shows orange-red light. The optimal Eu3 + concentration is 4 mol% in SrSb2O6:Eu3 + phosphor. SrSb2O6:Eu3 +, Bi3 + phosphor with excitation 254 and 394 nm emits orange-red light. Emission intensity of SrSb2O6:Eu3 + phosphor may be enhanced > 2 times by co-doping Bi3 + ion because of the fluxing agent and energy transfer roles of Bi3 + ion in SrSb2O6:Eu3 +, Bi3 + phosphor. The luminous mechanism of SrSb2O6:Eu3 +, Bi3 + phosphor is analyzed and explained by the simplified energy level diagrams of Sb2O62 - group, Bi3 + and Eu3 + ions, and energy transfer processes between them.

Hydrology, Water Quality, and Causes of Changes in Vegetation in the Vicinity of the Spring Bluff Nature Preserve, Lake County, Illinois, May 2007-August 2008

USGS Publications Warehouse

Kay, Robert T.; Miner, James J.; Maurer, Debbie A.; Knight, Charles W.

2010-01-01

Agriculture and urbanization have altered the hydrology and water quality of the coastal wetland complex along the shore of Lake Michigan at the Spring Bluff Nature Preserve and Illinois Beach State Park in northeastern Lake County, Ill., and the adjacent Chiwaukee Prairie State Natural Area in southeastern Wisconsin. Culverts, roads, ditches, and berms installed within the wetland complex have altered the natural directions of surface-water flow and likely have increased the natural hydroperiod in the Spring Bluff Nature Preserve and decreased it in the northern part of the Illinois Beach State Park. Relative to presettlement conditions, surface-water runoff into the wetlands likely is greater in quantity and higher in concentrations of several constituents, including chloride, nitrate, phosphorous, and suspended sediment. These constituent concentrations are affected by a variety of factors, including the amount of agricultural and urban land use in the watersheds. Hydrologic, chemical, and biologic processes within the wetland communities reduce the concentrations of these constituents in surface water before the water discharges to Lake Michigan by as much as 75 percent for chloride, 85 percent for nitrate, 66 percent for phosphorous, and more than an order of magnitude for suspended sediment. However, concentrations of phosphorous and suspended sediment in surface water increased within parts of the wetland complex. Given these changes, the floristic quality of these wetlands has been altered from the historic condition. Specifically, Typha spp. and Phragmites australis occur in greater numbers and over a larger area than in the past. The spread of Typha spp. and Phragmites australis appears to be enhanced by anthropogenic alterations within the wetland complex, such as increased water levels and duration of inundation and, possibly, increases in the total concentration of dissolved constituents in water.

Luminescence properties of Y2O3:Bi3+, Yb3+ co-doped phosphor for application in solar cells

NASA Astrophysics Data System (ADS)

Lee, E.; Kroon, R. E.; Terblans, J. J.; Swart, H. C.

2018-04-01

Bismuth (Bi3+) and ytterbium (Yb3+) co-doped yttrium oxide (Y2O3) phosphor powder was successfully synthesised using the co-precipitation technique. The X-ray diffraction (XRD) patterns confirmed that a single phase cubic structure with a Ia-3 space group was formed. The visible emission confirmed the two symmetry sites, C2 and S6, found in the Y2O3 host material and revealed that Bi3+ ions preferred the S6 site as seen the stronger emission intensity. The near-infrared (NIR) emission of Yb3+ increased significantly by the presence of the Bi3+ ions when compared to the singly doped Y2O3:Yb3+ phosphor with the same Yb3+ concentration. An increase in the NIR emission intensity was also observed by simply increasing the Yb3+ concentration in the Y2O3:Bi3+, Yb3+ phosphor material where the intensity increased up to x = 5.0 mol% of Yb3+ before decreasing due to concentration quenching.

Preparation and photoluminescence properties of red-emitting phosphor ZnAl2O4:Eu3+ with an intense 5D0 → 7F2 transition

NASA Astrophysics Data System (ADS)

He, Can; Ji, Haipeng; Huang, Zhaohui; Zhang, Xiaoguang; Liu, Haitao; Liu, Silin; Liu, Yangai; Fang, Minghao; Wu, Xiaowen; Min, Xin

2018-02-01

A series of ZnAl2-x O4:xEu3+ phosphors was synthesized by a modified co-precipitation method. The phase structure and photoluminescence properties were examined and extensively discussed. Composition-optimized ZnAl1.97O4:0.03Eu3+ exhibited sharp, intense red characteristic emissions with the Commission Internationale de l’Eclairage coordinates of (0.62, 0.33) peaking at 620 nm under an excitation at 394 nm, corresponding to the 5D0 → 7F2 transition of Eu3+. The quenching concentration of Eu3+ in ZnAl2-x O4:xEu3+ phosphors was approximately 0.03. In addition, the concentration quenching mechanism, fluorescence decay curves, and thermally stable luminescence properties of ZnAl2-x O4:xEu3+ phosphors were investigated. The results indicated that ZnAl2-x O4:xEu3+ phosphors demonstrate potential applications in near-ultraviolet light-emitting diode pumped white light lamps.

Synthesis and photoluminescence study in Eu3+:Y2WO6 phosphors

NASA Astrophysics Data System (ADS)

Sonali, Mondal, Manisha; Rai, Vineet Kumar

2018-05-01

Eu3+ doped Y2WO6 phosphors were synthesized by solid state reaction method. The photoluminescence properties of the Eu3+:Y2WO6 phosphors were studied for different concentration of Eu3+ ions. The luminescence intensity is found maximum at 0.3 mol% of Eu3+ ions. The excitation spectra monitored at ˜617 nm lies in the 220 - 350 nm region occurs due to charge transfer state (CTS) band of the europium-oxygen interactions, which is caused by an electron transfer from oxygen 2p orbital to an empty 4f shell of europium ions. The phosphors effectively excited by ˜393 nm near-ultraviolet (NUV) light gives efficient red emission band (˜ 617 nm) corresponding to 5D0 → 7F2 transition. The concentration dependence photoluminescence study and the mechanisms behind the photoluminescence properties have been explored with the help of suitable energy level diagram. Moreover, the CIE colour coordinate lie in the near white region so the prepared phosphors can be suitably use in making visible downconverter and in making visible light display devices.

Optimization of photoluminescence of GdAl3(BO3)4:Sm3+ phosphors for solid state lighting devices

NASA Astrophysics Data System (ADS)

Jamalaiah, Bungala Chinna

2017-10-01

The GdAl3(BO3)4:Sm3+ phosphors prepared by solid-state reaction method were characterized through thermal, structural and photoluminescence studies at room temperature only. The observed X-ray diffraction peaks were well consistent with JCPDS No. 83-1907. When excited with 406 nm wavelength, the studied phosphors exhibit orange-red luminescence through 4G5/2 → 6H5/2, 4G5/2 → 6H7/2 and 4G5/2 → 6H9/2 transitions. The concentration of Sm3+ ions was optimized to be 0.01 mol% for intense luminescence in GdAl3(BO3)4:Sm3+ phosphors. Beyond 0.01 mol% of Sm3+ ions concentration, luminescence quenching was observed due to energy transfer among the excited Sm3+ ions through cross-relaxation and dipole-dipole interaction mechanisms. The GdAl3(BO3)4:0.01 mol% Sm3+ phosphor was identified as a notable host material to emit intense orange-red luminescence for various solid state lighting devices under 406 nm excitation.

Photoluminescence properties of novel KBaBP2O8:M (M = Pb2+ and Bi3+) phosphors

NASA Astrophysics Data System (ADS)

Han, Bing; Zhang, Jie; Li, Pengju; Li, Jianliang; Bian, Yang; Shi, Hengzhen

2014-11-01

A series of novel inorganic phosphors KBa1-xPbxBP2O8 and K1+xBa1-2xBixBP2O8 (0.01 ⩽ x ⩽ 0.08) were synthesized by using a solid-state reaction technique at high-temperature and their photoluminescence properties were investigated. The dependence of the emission intensity on the Pb2+ and Bi3+ concentration for the KBa1-xPbxBP2O8 and K1+xBa1-2xBixBP2O8 was studied, in which the optimal concentration as well as the critical transfer distance Rc for Pb2+ and Bi3+ was obtained and determined. The as-prepared phosphors can be effectively excited with ultraviolet (UV), and exhibit UV - blue emission with large Stokes shift. The above work indicates these phosphors could be potential candidates for application in UV lamps industry.

Instense red phosphors for UV light emitting diode devices.

PubMed

Cao, Fa-Bin; Tian, Yan-Wen; Chen, Yong-Jie; Xiao, Lin-Jiu; Liu, Yun-Yi

2010-03-01

Ca(x)Sr1-x-1.5y-0.5zMoO4:yEu3+ zNa+ red phosphors were prepared by solid-state reaction using Na+ as charge supply for LEDs (light emitting diodes). The content of charge compensator, Ca2+ concentration, synthesis temperature, reaction time, and Eu3+ concentration were the keys to improving the properties of luminescence and crystal structure of red phosphors. The photoluminescence spectra shows the red phosphors are effectively excited at 616 nm by 311 nm, 395 nm, and 465 nm light. The wavelengths of 395 and 465 nm nicely match the widely applied emission wavelengths of ultraviolet or blue LED chips. Its chromaticity coordinates (CIE) are calculated to be x = 0.65, y = 0.32. Bright red light can be observed by the naked eye from the LED-based Ca0.60Sr0.25MoO4:0.08Eu3+ 0.06Na+.

Synthesis and photoluminescence properties of Pb2+ doped inorganic borate phosphor NaSr4(BO3)3

NASA Astrophysics Data System (ADS)

Chauhan, A. O.; Koparkar, K. A.; Bajaj, N. S.; Omanwar, S. K.

2016-05-01

A series of Inorganic borate phosphors NaSr4(BO3)3 doped with Pb2+ was successfully synthesized by modified solid state diffusion method. The crystal structure and the phase purity of sample were characterized by powder X-ray diffraction (XRD). The photoluminescence properties of synthesized materials were investigated using spectrofluorometer at room temperature. The phosphor show strong broad band emission spectra in UVA region maximum at 370 nm under the excitation of 289 nm. The dependence of the emission intensity on the Pb2+ concentration for the NaSr4(BO3)3 were studied in details. The concentration quenching of Pb2+ doped NaSr4(BO3)3 was observed at 0.02 mol. The Stokes shifts of NaSr4(BO3)3: Pb2+ phosphor was calculated to be 7574 cm-1.

Potential of Sm3+ doped LiSrVO4 nanophosphor to fill amber gap in LEDs

NASA Astrophysics Data System (ADS)

Biswas, P.; Kumar, Vinay; Sharma, Vishal; Bedyal, A. K.; Padha, Naresh; Swart, H. C.

2018-04-01

The LiSrVO4:Sm3+ phosphor powders were synthesized by the combustion method by varying the concentration of the Sm3+ ions from 0.25 mol% to 2.5 mol%. The powder X-ray diffraction (XRD) studies confirmed that the phosphors were crystallized as monoclinic structure belonging to space group P2/m and the transmission electron microscopy (TEM) revealed nanosized grains of the powders. The Fourier transform infrared studies (FTIR) established the formation of non-hygroscopic vanadate powders. The photoluminescence (PL) and diffused reflectance studies (DRS) were also carried out and discussed. Under 401 nm excitation, the optimized phosphor exhibited the characteristic 568, 600, 646 and 704 nm emissions of Sm3+ which corresponded to the orange-red (amber) color with (0.59, 0.41) Commission Internationale de' Eclairage (CIE) chromaticity coordinates. Concentration quenching of phosphor intensity on account of non-radiative energy transfer was ascribed to dipole-dipole interaction between activators. DRS study reveals that the host of the phosphor is a wide bandgap material which accommodates the dopant successfully. The present results signify that the LiSrVO4:Sm3+ phosphor can suitably be excited by the GaN family of UV-LEDs chips for efficient amber LEDs applications.

Photoluminescence properties and structure of double perovskite Ba2ZnWO6:Eu3+, Li+ as a novel red emitting phosphor

NASA Astrophysics Data System (ADS)

Chen, Peng; Yang, Dingming; Hu, Wenyuan; Zhang, Jing; Wu, Yadong

2017-12-01

Novel red-emitting Ba2Zn1-x-yWO6:xEu3+, yLi+ phosphors were prepared using a high-temperature solid-state method, and the crystal structure, the photoluminescence properties and the doping concentrations of Eu3+ and Li+ were investigated. The results show that these phosphors can be excited by near-ultraviolet light (250-400 nm) and co-doped Li+ can significantly enhance their PL performance. An intense red emission peak at 598 nm (5D0-7F1 transitions) was observed with an excitation wavelength of 316 nm. The CIE chromaticity coordinates of the phosphors are located in the red region, indicating that the BZW:Eu3+, Li+ phosphor holds promise as a red phosphor for near-ultraviolet excited WLEDs.

Synthesis and Photoluminescence Properties of Li2SrSiO4 Activated with Dy3+ and Sm3+

NASA Astrophysics Data System (ADS)

Erdoğmuş, E.

2015-01-01

Li2SrSiO4:M (M: Dy3+ and Sm3+) phosphors were synthesized by the conventional solid state reaction. The synthesized materials were characterized by powder XRD. The emission and excitation spectra of these phosphors were measured at room temperature with a spectrofluorometer. The first phosphor, Li2SrSiO4:Dy3+, emits at 479, 573, and 666 nm upon 351 nm excitation. The second phosphor, Li2SrSiO4:Sm3+, emits at 561-571, 594, 647-655, and 703-713 nm upon 399 nm excitation. Also, the dependence of the photoluminescence properties of both phosphors on boric acid concentration was investigated. The results showed that boric acid was effective in improving the photoluminescence intensity of both phosphors.

Effect of phosphorous concentrations on sedimentary distributions and isotopic composition of algal lipid biomarkers in lakes from central Switzerland

NASA Astrophysics Data System (ADS)

Ladd, N.; Dubois, N.; Schubert, C. J.

2015-12-01

Lakes in the Swiss central plateau experienced increasing anthropogenic phosphorous loading throughout much of the 20th century. Since the 1980s concerted remediation efforts on the part of the Swiss government have significantly reduced P concentrations in most lakes and reversed previous eutrophication. However, P concentrations remain elevated above their preindustrial levels in many sites. High quality monitoring of lake nutrient levels since the 1950s, along with several lakes of wide-ranging P concentrations in close proximity, make central Switzerland an ideal location for studying the ways in which nutrient loading affects the organic composition of lacustrine sediments. Results of such studies can be used to develop proxies of eutrophication in sites where fewer historical data exist, and to reconstruct historical P concentrations in local lakes from the time before record keeping began. We analyzed the distributions of algal lipid biomarkers from surface sediment and sediment traps collected in the spring of 2015 from ten lakes with variable P concentrations in central Switzerland. Sedimentary lipid distributions from these lakes confirm that biomarkers associated with algal and cyanobacterial sources are more abundant in the sediment of lakes with greater P loading. The dry sedimentary concentrations of biomarkers such as brassicasterol (primarily diatom source) and diplopterol (cyanobacteria source), as well as the less source specific short-chain n-alkanols, linearly increase from 0.3 - 1.9 μg/g as total phosphorous in the upper water column increases by 1 μg/L over a range of 7 - 50 μg/L. We also present preliminary hydrogen isotope data from these biomarkers. Hydrogen isotopes of algal lipids primarily reflect the source water in which the algae grew, and this relationship has been developed as a paleohydrologic proxy. However, laboratory cultures of marine algae demonstrate that they discriminate more against 2H under nutrient replete conditions. We present the first field assessment of how nutrient availability influences 2H fractionation in freshwater algae, and demonstrate how such measurements can be used to infer past information about anthropogenic nutrient loading.

Microalgal cultivation in wastewater from the fermentation effluent in Riboflavin (B2) manufacturing for biodiesel production.

PubMed

Sun, Xuefei; Wang, Cunwen; Li, Zihao; Wang, Weiguo; Tong, Yanjie; Wei, Jiang

2013-09-01

In this work, the acclimation of Chlorella pyrenoidosa in diluted wastewater was studied to produce biomass and remove chemical oxygen demand (COD), ammonia-N and phosphorous. The results indicated that the optimal conditions (the volume ratio of wastewater, light intensity, culture temperature, CO2 concentration in feeding gas) which could influence the wastewater treatment efficiency were 0.05, 250 photons m(-2) s(-1), 28 °C and 5%, respectively. Under these conditions, the removal efficiency of COD reached up to 89.2%, while the total nitrogen and total phosphorous decreased by 64.52% and 82.20%, respectively. With the second treatment, COD in the wastewater was further reduced to less than 100 mg/L while it was only reduced to 542.9 mg/L after the first treatment. The treated wastewater could be discharged directly or subjected to for further treatment for recycling. In addition, 1.25 g/L of the biomass and 38.27% (dry basis, w%) of lipid content were reached after microalgal cultivation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Color tunable emission through energy transfer from Yb3+ co-doped SrSnO3: Ho3+ perovskite nano-phosphor

NASA Astrophysics Data System (ADS)

Jain, Neha; Singh, Rajan Kr.; Sinha, Shriya; Singh, R. A.; Singh, Jai

2018-04-01

First time color tunable lighting observed from Ho3+ and Yb3+ co-doped SrSnO3 perovskite. Down-conversion and up-conversion (UC) photoluminescence emission spectra were recorded to understand the whole mechanism of energy migration between Ho3+ and Yb3+ ions. The intensity of green and red emission varies with Yb3+ doping which causes multicolour emissions from nano-phosphor. The intensity of UC red emission (654 nm) obtained from 1 at.% Ho3+ and 3 at.% Yb3+ co-doped nano-phosphor is nine times higher than from 1 at.% Ho3+ doped SrSnO3 nano-phosphor. Enhanced brightness of 654 nm in UC process belongs in biological transparency window so that it might be a promising phosphor in the bio-medical field. Moreover, for the other Yb3+ co-doped nano-phosphor, Commission Internationale de l'Éclairage chromaticity co-ordinates were found near the white region and their CCT values lie in the range 4900-5100 K indicating cool white. Decay time was measured for 545 nm emission of Ho3+ ion found in 7.652 and 8.734 µs at 355 nm excitation. The variation in lifetime was observed in ascending order with increasing Yb3+ concentration which supports PL emission spectra observation that with increasing Yb3+ concentration, rate of transition has changed. These studies reveal that Ho3+ and Yb3+ co-doped phosphor is useful for fabrication of white LEDs.

Method and apparatus for reading thermoluminescent phosphors

DOEpatents

Braunlich, Peter F.; Tetzlaff, Wolfgang

1987-01-01

An apparatus and method for rapidly reading thermoluminescent phosphors to determine the amount of luminescent energy stored therein. The stored luminescent energy is interpreted as a measure of the total exposure of the thermoluminescent phosphor to ionizing radiation. The thermoluminescent phosphor reading apparatus uses a laser to generate a laser beam. The laser beam power level is monitored by a laser power detector and controlled to maintain the power level nearly constant. A shutter or other laser beam interrupting means is used to control exposure of the thermoluminescent phosphor to the laser beam. The laser beam can be equalized using an optical equalizer so that the laser beam has an approximately uniform power density across the beam. The heated thermoluminescent phosphor emits a visible or otherwise detectable luminescent emission which is measured as an indication of the radiation exposure of the thermoluminescent phosphors. Also disclosed are preferred signal processing and control circuits.

Francis E. Walter Dam and Reservoir Project, Water Quality Data Report (RCS-DAEN-CWE-15).

DTIC Science & Technology

1980-12-01

downstream, as well as within, the lake. Analysis of these samples rives an understanding of the effect of the lake on water quality: • . The...regulation, are available for analysis . Water quality data;I (temperature, dissolved oxygen, conductivity, pH, phosphorous, total dissolved solids...depresses the pH following a rain storm. If the source of tre acid water is Fhallow lakes and swamps~lignin and tannin concentrations would be high

Electrocatalysis of fuel cell reactions: Investigation of alternate electrolytes

NASA Technical Reports Server (NTRS)

Chin, D. T.; Hsueh, K. L.; Chang, H. H.

1983-01-01

Oxygen reduction and transport properties of the electrolyte in the phosphoric acid fuel cell are studied. A theoretical expression for the rotating ring-disk electrode technique; the intermediate reaction rate constants for oxygen reduction on platinum in phosphoric acid electrolyte; oxygen reduction mechanism in trifluoromethanesulfonic acid (TFMSA), considered as an alternate electrolyte for the acid fuel cells; and transport properties of the phosphoric acid electrolyte at high concentrations and temperatures are covered.

Efficient rare-earth free red-emitting Ca2YSbO6:Mn4+,M(M = Li+, Na+, K+, Mg2+) phosphors for white light-emitting diodes.

PubMed

Zhong, Jiasong; Chen, Daqin; Chen, Xiao; Wang, Keyuan; Li, Xinyue; Zhu, Yiwen; Ji, Zhenguo

2018-05-08

Owing to its low-cost and satisfactory luminescent-emission performance in warm white light-emitting diodes (w-LEDs), the non-rare-earth Mn4+-activated red phosphor has become a promising competitor of commercial rare-earth doped phosphor. In this study, a series of novel red-light emitting phosphors based on Ca2YSbO6:Mn4+ have been developed successfully by a conventional solid-state reaction. The structural and luminescent properties of these phosphors are systematically investigated. The as-prepared Ca2YSbO6:Mn4+ product exhibits a broad excitation band ranging from 250 to 600 nm and an abnormal intense deep-red emission centered at 680 nm with a full width at half maximum (FWHM) of ∼46 nm. The optimal Mn4+ doping concentration is about 0.3 mol%, and the concentration quenching mechanism is determined to be a dipole-dipole interaction. Impressively, the Ca2YSbO6:0.003Mn4+ phosphor shows an outstanding quantum efficiency of 62.6% and an excellent thermal stability. In addition, the effect of Li+, Mg2+, Na+ and K+ dopants on the luminescent properties of Mn4+-doped Ca2YSbO6 phosphors is elucidated. Furthermore, by employing the as-prepared Ca2YSbO6:Mn4+ as a red component, a warm w-LED with high color rendering index (Ra = 87.5) and low correlated color temperature (CCT = 3255 K) can be acquired. It is believed that the present phosphor has a potential application as a supplement of the red component for warm w-LEDs.

Composite phase ceramic phosphor of Al₂O₃-Ce:YAG for high efficiency light emitting.

PubMed

Tang, Yanru; Zhou, Shengming; Chen, Chong; Yi, Xuezhuan; Feng, Yue; Lin, Hui; Zhang, Shuai

2015-07-13

We present our achievement which is a ceramic plate phosphorable to produce white light when directly combined with commercially available blue light emitting diodes. The ceramic phase structure is that the Al₂O₃ particle is uniformly distributed in the Ce:YAG matrix. The Al₂O₃-Ce:YAG ceramic phosphor has a better luminous efficacy than the transparent Ce:YAG ceramic phosphor under the same test condition. The Al₂O₃ particle plays an important role in promoting the luminous efficacy. The Al₂O₃ particle changes the propagation of the light in ceramic, and it reduces the total internal reflection. That is why the composite phase ceramic phosphor improves extraction efficiency of light.

Counting the Photons: Determining the Absolute Storage Capacity of Persistent Phosphors

PubMed Central

Rodríguez Burbano, Diana C.; Capobianco, John A.

2017-01-01

The performance of a persistent phosphor is often determined by comparing luminance decay curves, expressed in cd/m2. However, these photometric units do not enable a straightforward, objective comparison between different phosphors in terms of the total number of emitted photons, as these units are dependent on the emission spectrum of the phosphor. This may lead to incorrect conclusions regarding the storage capacity of the phosphor. An alternative and convenient technique of characterizing the performance of a phosphor was developed on the basis of the absolute storage capacity of phosphors. In this technique, the phosphor is incorporated in a transparent polymer and the measured afterglow is converted into an absolute number of emitted photons, effectively quantifying the amount of energy that can be stored in the material. This method was applied to the benchmark phosphor SrAl2O4:Eu,Dy and to the nano-sized phosphor CaS:Eu. The results indicated that only a fraction of the Eu ions (around 1.6% in the case of SrAl2O4:Eu,Dy) participated in the energy storage process, which is in line with earlier reports based on X-ray absorption spectroscopy. These findings imply that there is still a significant margin for improving the storage capacity of persistent phosphors. PMID:28773228

The Preparation and Optical Properties of Novel LiLa(MoO4)2:Sm3+,Eu3+ Red Phosphor

PubMed Central

Luo, Li; Huang, Baoyu; He, Jingqi; Zhang, Wei; Zhao, Weiren; Wang, Jianqing

2018-01-01

Novel LiLa1−x−y(MoO4)2:xSm3+,yEu3+ (in short: LL1−x−yM:xSm3+,yEu3+) double molybdate red phosphors were synthesized by a solid-state reaction at as low temperature as 610 °C. The optimal doping concentration of Sm3+ in LiLa1−x(MoO4)2:xSm3+ (LL1−xM:xSm3+) phosphor is x = 0.05 and higher concentrations lead to emission quenching by the electric dipole—electric dipole mechanism. In the samples co-doped with Eu3+ ions, the absorption spectrum in the near ultraviolet and blue regions became broader and stronger than these of the Sm3+ single-doped samples. The efficient energy transfer from Sm3+ to Eu3+ was found and the energy transfer efficiency was calculated. Under the excitation at 403 nm, the chromaticity coordinates of LL0.95−yM:0.05Sm3+,yEu3+ approach to the NTSC standard values (0.670, 0.330) continuously with increasing Eu3+ doping concentration. The phosphor exhibits high luminous efficiency under near UV or blue light excitation and remarkable thermal stability. At 150 °C, the integrated emission intensity of the Eu3+ remained 85% of the initial intensity at room temperature and the activation energy is calculated to be 0.254 eV. The addition of the LL0.83M:0.05Sm3+,0.12Eu3+ red phosphors can improve the color purity and reduce the correlated color temperature of WLED lamps. Hence, LL1−x−yM:xSm3+,yEu3+ is a promising WLED red phosphor. PMID:29443910

The Preparation and Optical Properties of Novel LiLa(MoO4)2:Sm3+,Eu3+ Red Phosphor.

PubMed

Wang, Jiaxi; Luo, Li; Huang, Baoyu; He, Jingqi; Zhang, Wei; Zhao, Weiren; Wang, Jianqing

2018-02-14

Novel LiLa1-x-y(MoO4)2:xSm3+,yEu3+ (in short: LL1-x-yM:xSm3+,yEu3+) double molybdate red phosphors were synthesized by a solid-state reaction at as low temperature as 610 °C. The optimal doping concentration of Sm3+ in LiLa1-x(MoO4)2:xSm3+ (LL1-xM:xSm3+) phosphor is x = 0.05 and higher concentrations lead to emission quenching by the electric dipole-electric dipole mechanism. In the samples co-doped with Eu3+ ions, the absorption spectrum in the near ultraviolet and blue regions became broader and stronger than these of the Sm3+ single-doped samples. The efficient energy transfer from Sm3+ to Eu3+ was found and the energy transfer efficiency was calculated. Under the excitation at 403 nm, the chromaticity coordinates of LL0.95-yM:0.05Sm3+,yEu3+ approach to the NTSC standard values (0.670, 0.330) continuously with increasing Eu3+ doping concentration. The phosphor exhibits high luminous efficiency under near UV or blue light excitation and remarkable thermal stability. At 150 °C, the integrated emission intensity of the Eu3+ remained 85% of the initial intensity at room temperature and the activation energy is calculated to be 0.254 eV. The addition of the LL0.83M:0.05Sm3+,0.12Eu3+ red phosphors can improve the color purity and reduce the correlated color temperature of WLED lamps. Hence, LL1-x-yM:xSm3+,yEu3+ is a promising WLED red phosphor.

Iron Redox Transformations And Phosphorous Cycling In Tropical Soils

NASA Astrophysics Data System (ADS)

Peretyazhko, T.; Sposito, G.

2003-12-01

We are investigating the hypothesis that in highly weathered tropical soils iron oxidation-reduction reactions may mediate phosphorous solubility. In these soils phosphorous may be removed from the plant-available soil pool by sorption to Fe(III) oxides and by precipitation with Fe(III) to form insoluble minerals. The reduction of iron during episodic anoxic conditions has the potential to release phosphorous in a plant available form. We aim to explore the factors controlling Fe reduction and to evaluate the role of Fe reduction in P solubilization. Soil samples were collected along a toposequence (ridge-slope-valley) in the Luquillo Experimental Forest, Puerto Rico. Besides precipitation, the valley soils receive additional water through subsurface and upland runoff. These soils are poorly-drained and, therefore, periodically saturated with water, which creates anoxic conditions. Two series of incubation experiments were carried out on air-dried and freshly-sampled valley soils. During a 14-day incubation period, increasing production of Fe(II) was detected in both types of soil sample. We also found positive correlations between the concentrations of soluble Fe(II), pH, and soluble P. In general, the total amounts of Fe(II) and P produced were higher in the air-dried soil, mainly due to differences in microbial activity. To examine further the factors controlling Fe reduction and P solubilization, we are performing soil incubation experiments in the presence of "electron shuttle" compound (AQDS). SEM and STXM techniques will be applied to detect the formation of Fe(II) secondary minerals.

Thermoluminescent properties of rare earth doped lithium strontium borate phosphors

NASA Astrophysics Data System (ADS)

Jakathamani, S.; Annalakshmi, O.; Jose, M. T.

2018-04-01

Thermoluminescence (TL) of borates is remarkable in the field of radiation dosimetry because they can detect both neutron and gamma radiations. Usually, the TL efficiency of pure borates is low and hence dopants have to be added to increase their TL output. Their sensitivity and thermal stability vary widely and depend strongly on the preparation method. In this study polycrystalline powders of different rare earth doped thermoluminescent phosphors of Lithium Strontium borate (LSB) were synthesized by solid state sintering technique. Among the different rare earth dopants, the phosphor doped with cerium was found to have a simple glow curve structure with a dosimetric peak at around 265°C for a heating rate of 5°C/s. In order to study the effect of dopant on the TL characteristics, LSB phosphor with different concentrations of Ce dopant was synthesized and the TL intensity was found to be maximum for a dopant concentration of 0.7 mol%. All other important dosimetric characteristics like dose response and fading were carried out for the LSB:Ce (0.7 mol%) phosphor. Kinetic parameters like trap depth and frequency factor were determined using Peak shape method from Chen's equation.

Ionic liquid-assisted hydrothermal synthesis of dendrite-like NaY(MoO4)2:Tb3+ phosphor

NASA Astrophysics Data System (ADS)

Tian, Yue; Chen, Baojiu; Tian, Bining; Sun, Jiashi; Li, Xiangping; Zhang, Jinsu; Cheng, Lihong; Zhong, Haiyang; Zhong, Hua; Meng, Qingyu; Hua, Ruinian

2012-07-01

Micro-sized NaY(MoO4)2:Tb3+ phosphors with dendritic morphology was synthesized by a ionic liquid-assisted hydrothermal process. X-ray diffraction (XRD) indicated that the as-prepared product is pure tetragonal phase of NaY(MoO4)2. Field emission scanning electron microscopy (FE-SEM) images showed that the as-prepared NaY(MoO4)2:Tb3+ phosphors have dendritic morphology. The photoluminescent (PL) spectra displayed that the as-prepared NaY(MoO4)2:Tb3+ phosphors show a stronger green emission with main emission wavelength 545 nm corresponding to the 5D4→7F5 transition of Tb3+ ion, and the optimal Tb3+ doping concentration for obtaining maximum emission intensity was confirmed to be 10 mol%. Based on Van Uitert's and Dexter's models the electric dipole-dipole (D-D) interaction was confirmed to be responsible for the concentration quenching of 5D4 fluorescence of Tb3+ in the NaY(MoO4)2:Tb3+ phosphors. The intrinsic radiative transition lifetime of 5D4 level is found to be 0.703 ms.

Synthesis and luminescence properties of blue-emitting phosphor Ca12 Al14 O32 F2 :Eu2+ for white light-emitting diode.

PubMed

Chen, Wanping; Zhang, Xinzhu; Wang, Liping

2017-09-01

A blue-emitting phosphor Ca 12 Al 14 O 32 F 2 :Eu 2+ was synthesized using a high-temperature solid-state reaction under a reductive atmosphere. The X-ray diffraction measurements indicate that a pure phase Ca 12 Al 14 O 32 F 2 :Eu 2+ can be obtained for low doping concentration of Eu 2+ . The phosphor has a strong absorption in the range 270-420 nm with a maximum at ~340 nm and blue emission in the range 400-500 nm with chromatic coordination of (0.152, 0.045). The optimal doping concentration is ~0.24. In addition, the luminescence properties of the as-synthesized phosphor were evaluated by comparison with those of Ca 12 Al 14 O 32 Cl 2 :Eu 2+ and the commercially available phosphor BaMgAl 10 O 17 :Eu 2+ . The emission intensity of Ca 12 Al 14 O 32 F 2 :Eu 2+ was ~72% that of BaMgAl 10 O 17 :Eu 2+ under excitation at λ = 375 nm. The results indicate that Ca 12 Al 14 O 32 F 2 :Eu 2+ has potential application as a near-UV-convertible blue phosphor for white light-emitting diodes. Copyright © 2017 John Wiley & Sons, Ltd.

Enhancing luminescence of Lu{sub 2}MoO{sub 6}:Eu{sup 3+} phosphors by doping with Li{sup +} ions for near ultraviolet based solid state lighting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Li, E-mail: lilic@cqupt.edu.cn; Shen, Jun; Pan, Yu

Graphical abstract: The emission spectra of Lu{sub 2}MoO{sub 6}:3%Eu{sup 3+}, x%Li{sup +} phosphors under 365 nm excitation. The inset represents emission intensity of 610 nm as a function of Li{sup +} molar concentration. - Highlights: • Lu{sub 2}MoO{sub 6}:3%Eu{sup 3+}, x%Li{sup +} phosphors were synthesized by solid-state reaction method. • All the prepared phosphors can be assigned to its monoclinic phase. • The optimal concentration of Li{sup +} ions is 30mol%. • The luminescent intensity of Lu{sub 2}MoO{sub 6}:Eu{sup 3+} phosphors has been greatly enhanced by codoping Li{sup +} ions. - Abstract: Lu{sub 2}MoO{sub 6}: 3% Eu{sup 3+} co-doped withmore » x% Li{sup +} (x = 0–40 mol) phosphors were synthesized by high-temperature solid-state reaction method. The structure and luminescent properties of these phosphors were investigated. The X-ray diffraction (XRD) results show that all prepared phosphors can be assigned to monoclinic phase and codoping with Li{sup +} ions does not change their crystallographic structure. The excitation and emission spectra show that the samples can be effectively excited by the near ultraviolet light at 365 nm and exhibit strong red emission centered at 610 nm. The experimental results indicate the red luminescent intensity of Lu{sub 2}MoO{sub 6}:Eu{sup 3+} phosphors has been greatly enhanced by codoping with Li{sup +} ions. The enhancement of the luminescent intensity can be the consequence of the modification of the local field symmetry around the Eu{sup 3+} ion, improved crystallization, and the enlarged grain size induced by the Li{sup +} ions.« less

White light emission and effect of annealing on the Ho{sup 3+}–Yb{sup 3+} codoped BaCa{sub 2}Al{sub 8}O{sub 15} phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumari, Astha; Rai, Vineet Kumar, E-mail: vineetkrrai@yahoo.co.in

Graphical abstract: The upconversion emission spectra of the Ho{sup 3+}/Yb{sup 3+} doped/codoped BaCa{sub 2}Al{sub 8}O{sub 15} phosphors with different doping concentrations of Ho{sup 3+}/Yb{sup 3+} ions along with UC emission spectrum of the white light emitting phosphor annealed at 800 °C. - Highlights: • BaCa{sub 2}Al{sub 8}O{sub 15} phosphors codoped with Ho{sup 3+}–Yb{sup 3+} have been prepared by combustion method. • Phosphor annealed at 800 °C, illuminate an intense white light upon NIR excitation. • The sample annealed at higher temperatures emits in the pure green region. • The colour emitted persists in the white region even at high pumpmore » power density. • Developed phosphor is suitable for making upconverters and WLEDs. - Abstract: The BaCa{sub 2}Al{sub 8}O{sub 15} (BCAO) phosphors codoped with suitable Ho{sup 3+}–Yb{sup 3+} dopant concentration prepared by combustion method illuminate an intense white light upon near infrared diode laser excitation. The structural analysis of the phosphors and the detection of impurity contents have been performed by using the X-Ray Diffraction, FESEM and FTIR analysis. The purity of white light emitted from the sample has been confirmed by the CIE chromaticity diagram. Also, the white light emitted from the sample persists with the variation of pump power density. The phosphors emit upconversion (UC) emission bands in the blue, green and red region (three primary colours required for white light emission) along with one more band in the near infrared region of the electromagnetic spectrum. On annealing the white light emitting sample at higher temperatures, the sample starts to emit green colour and also the intensity of green and red UC emission bands get enhanced largely.« less

Photoluminescence analysis of Ce3+:Zn2SiO4 & Li++ Ce3+:Zn2SiO4: phosphors by a sol-gel method

NASA Astrophysics Data System (ADS)

Babu, B. Chandra; Vandana, C. Sai; Guravamma, J.; Rudramadevi, B. Hemalatha; Buddhudu, S.

2015-06-01

Here, we report on the development and photoluminescence analysis of Zn2SiO4, Ce3+:Zn2SiO4 & Li+ + Ce3+: Zn2SiO4 novel powder phosphors prepared by a sol-gel technique. The total amount of Ce3+ ions was kept constant in this experiment at 0.05 mol% total doping. The excitation and emission spectra of undoped (Zn2SiO4) and Ce3+ doped Zn2SiO4 and 0.05 mol% Li+ co-doped samples have been investigated. Cerium doped Zn2SiO4 powder phosphors had broad blue emission corresponding to the 2D3/2→2FJ transition at 443nm. Stable green-yellow-red emission has been observed from Zn2SiO4 host matrix and also we have been observed the enhanced luminescence of Li+ co-doped Zn2SiO4:Ce3+. Excitation and emission spectra of these blue luminescent phosphors have been analyzed in evaluating their potential as luminescent screen coating phosphors.

Influence of anodization parameters on the volume expansion of anodic aluminum oxide formed in mixed solution of phosphoric and oxalic acids

NASA Astrophysics Data System (ADS)

Kao, Tzung-Ta; Chang, Yao-Chung

2014-01-01

The growth of anodic alumina oxide was conducted in the mixed solution of phosphoric and oxalic acids. The influence of anodizing voltage, electrolyte temperature, and concentration of phosphoric and oxalic acids on the volume expansion of anodic aluminum oxide has been investigated. Either anodizing parameter is chosen to its full extent of range that allows the anodization process to be conducted without electric breakdown and to explore the highest possible volume expansion factor. The volume expansion factors were found to vary between 1.25 and 1.9 depending on the anodizing parameters. The variation is explained in connection with electric field, ion transport number, temperature effect, concentration, and activity of acids. The formation of anodic porous alumina at anodizing voltage 160 V in 1.1 M phosphoric acid mixed with 0.14 M oxalic acid at 2 °C showed the peak volume expansion factor of 1.9 and the corresponding moderate growth rate of 168 nm/min.

Synthesis and photoluminescence properties of Pb{sup 2+} doped inorganic borate phosphor NaSr{sub 4}(BO{sub 3}){sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chauhan, A. O., E-mail: abhi2718@gmail.com; Koparkar, K. A.; Omanwar, S. K.

2016-05-06

A series of Inorganic borate phosphors NaSr{sub 4}(BO{sub 3}){sub 3} doped with Pb{sup 2+} was successfully synthesized by modified solid state diffusion method. The crystal structure and the phase purity of sample were characterized by powder X-ray diffraction (XRD). The photoluminescence properties of synthesized materials were investigated using spectrofluorometer at room temperature. The phosphor show strong broad band emission spectra in UVA region maximum at 370 nm under the excitation of 289 nm. The dependence of the emission intensity on the Pb{sup 2+} concentration for the NaSr{sub 4}(BO{sub 3}){sub 3} were studied in details. The concentration quenching of Pb{sup 2+}more » doped NaSr{sub 4}(BO{sub 3}){sub 3} was observed at 0.02 mol. The Stokes shifts of NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+} phosphor was calculated to be 7574 cm{sup −1}.« less

Phosphorus vertical migration in aquic brown soil and light chernozem under different phosphorous application rate: a soil column leaching experiment.

PubMed

Zhao, Muqiu; Chen, Xin; Shi, Yi; Zhou, Quanlai; Lu, Caiyan

2009-01-01

A soil column leaching experiment was conducted to study the vertical migration of phosphorus in aquic brown soil and light chernozem under different phosphorus fertilization rates. The results showed that total dissolved phosphorus concentration in the leachates from the two soils was nearly the same, but dissolved inorganic phosphorus concentration was obviously different. In all fertilization treatments, aquic brown soil had a higher content of phosphorus in calcium chloride extracts compared with light chernozem. But Olsen phosphorus content was higher at the soil depth beneath 0-20 cm, and increased with increasing phosphorus application rate.

Tunable Yellow-Red Photoluminescence and Persistent Afterglow in Phosphors Ca4LaO(BO3)3:Eu3+ and Ca4EuO(BO3)3.

PubMed

Chen, Zhen; Pan, Yuexiao; Xi, Luqing; Pang, Ran; Huang, Shaoming; Liu, Guokui

2016-11-07

In most Eu 3+ activated phosphors, only red luminescence from the 5 D 0 is obtainable, and efficiency is limited by concentration quenching. Herein we report a new phosphor of Ca 4 LaO(BO 3 ) 3 :Eu 3+ (CLBO:Eu) with advanced photoluminescence properties. The yellow luminescence emitted from the 5 D 1,2 states is not thermally quenched at room temperature. The relative intensities of the yellow and red emission bands depend strongly on the Eu 3+ doping concentration. More importantly, concentration quenching of Eu 3+ photoluminescence is absent in this phosphor, and the stoichiometric compound of Ca 4 EuO(BO 3 ) 3 emits stronger luminescence than the Eu 3+ doped compounds of CLBO:Eu; it is three times stronger than that of a commercial red phosphor of Y 2 O 3 :Eu 3+ . Another beneficial phenomenon is that ligand-to-metal charge transfer (CT) transitions occur in the long UV region with the lowest charge transfer band (CTB) stretched down to about 3.67 eV (∼330 nm). The CT transitions significantly enhance Eu 3+ excitation, and thus result in stronger photoluminescence and promote trapping of excitons for persistent afterglow emission. Along with structure characterization, optical spectra and luminescence dynamics measured under various conditions as a function of Eu 3+ doping, temperature, and excitation wavelength are analyzed for a fundamental understanding of electronic interactions and for potential applications.

Photoluminescence and thermal stability of yellow-emitting Na{sub 2}Ba{sub 2}Si{sub 2}O{sub 7}:Sm{sup 3+} phosphor for light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Jiayue, E-mail: jiayue_sun@126.com; Di, Qiumei; Cui, Dianpeng

2014-12-15

Highlights: • Na{sub 2}Ba{sub 2}Si{sub 2}O{sub 7}:Sm{sup 3+} phosphors are obtained via a solid-state reaction method. • Excitation at 402 nm, the yellow color purity is close to 100%. • The mechanism of concentration quenching is dipole–dipole interaction. • The temperature-dependent luminescence property exceed that of YAG:Ce{sup 3+}. - Abstract: A series of yellow-emitting Na{sub 2}(Ba{sub 2−x}Sm{sub x})Si{sub 2}O{sub 7} phosphors have been prepared via solid-state reaction technique. X-ray diffraction (XRD), photoluminescence (PL) spectra, temperature-dependent luminescence property, concentration quenching mechanism and luminescence lifetime are applied to characterize the obtained samples. Under 402 nm near ultraviolent excitation, the samples emit yellowmore » light and the color purity is close to 100%. The critical quenching concentration of Sm{sup 3+} in the Na{sub 2}Ba{sub 2}Si{sub 2}O{sub 7} host is about 3.6 mol% and corresponding quenching behavior is ascribed to be electric dipole–dipole interaction. Furthermore, the phosphor has good thermal stability property, superior to the commercial yellow Y{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} phosphor and the activation energy for thermal quenching is calculated as 0.18 eV.« less

Comparison analysis on the properties of the phosphor film according to the various composition ratio of phosphor slurry

NASA Astrophysics Data System (ADS)

Park, Jeong Yeon; Lee, Jeong Won; Heo, Young Moo; Won, Si Tae; Yoon, Gil Sang

2016-03-01

The conventional method of making a phosphor layer on the LED package by using a dispensing method is difficult to implement the specific color coordinate, color temperature and optical efficiency because the thickness of the phosphor layer is non-uniform due to precipitation of the phosphor. Besides, the dispensing method consume a large amount of phosphor and silicone to fill the LED package. Thus, studies that manufacture phosphor layer with a uniform thickness such as spray coating, screen printing, electrophoresis are active recently. The purpose of this study is to perform the basic research about the change of the characteristics of phosphor film that is molded with uniform thickness using the phosphor slurry according to various silicone resin and phosphor composition ratio. It is expected to be used as useful information for the fabricating properties when production environment of phosphor layer is changed dispensing method into phosphor film fabrication. In the experiment, it was selected three kinds of methyl-phenyl silicone based resin as the phosphor slurry constituents, and mixed with phosphor various amount of 20 ˜ 60wt% content per one silicone resin. Using this mixed phosphor slurry, it was molded the phosphor film with 300 μm thickness and analyzed the mechanical properties and optical properties of the phosphor film. Finally, the results of this study are presented below: (a) As the phenyl group content is increased, the total heat of reaction need to cure the silicone resin is decrease, and also lower the durometer hardness of the phosphor sheet. On the other hand, it was confirmed that there is no relationship between the phenyl group content in the phosphor film and optical characteristics of the phosphor film. (b) If the amount of the phosphor within the film are increased, then the values of shore hardness and CIE color coordinates are increased gradually but the value of CIE color temperature is decreased gradually in case of being applied same silicone resin to the phosphor film.

Enhanced photoluminescence property and broad color emission of ZnGa2O4 phosphor due to the synergistic role of Eu3+ and carbon dots

NASA Astrophysics Data System (ADS)

Huo, Qiuyue; Tu, Weixia; Guo, Lin

2017-10-01

ZnGa2O4 phosphors co-composited with nanoscale carbon dots (CDs) and Eu3+ were presented for the tunable color emission. Novel single phase CDs or/and Eu3+ composited ZnGa2O4 phosphors were synthesized by microwave hydrothermal method and their optical properties were investigated. The ZnGa2O4 phosphors composited with CDs exhibited an intense broad blue light emission at 421 nm and a more enhanced photoluminescence intensity than those without CDs. The Eu3+ composited ZnGa2O4 phosphors gave an ideal red color emission. The CDs/Eu3+ co-composited ZnGa2O4 phosphors exhibited a wide emission band peak at 450 nm and narrow emission peak at 618 nm. Furthermore, the tunable color emissions of CDs/Eu3+ co-composited ZnGa2O4 phosphors from blue to the white light region, and then to red were obtained with the increasing Eu3+ concentration, which can be a promising single phased phosphor candidate in light emitting diodes. Broadly tunable emission single phased phosphor is tuned firstly through the synergistic role of the non-metal element and the rare earth metal ions.

Apparatuses and methods for laser reading of thermoluminescent phosphors

DOEpatents

Braunlich, Peter F.; Tetzlaff, Wolfgang

1989-01-01

Apparatuses and methods for rapidly reading thermoluminescent phosphors to determine the amount of luminescent energy stored therein. The stored luminescent energy is interpreted as a measure of the total exposure of the thermoluminescent phosphor to ionizing radiation. The thermoluminescent phosphor reading apparatus uses a laser to generate a laser beam. The laser beam power level is monitored by a laser power detector and controlled to maintain the power level at a desired value or values which can vary with time. A shutter or other laser beam interrupting means is used to control exposure of the thermoluminescent phosphor to the laser beam. The laser beam can be equalized using an opitcal equalizer so that the laser beam has an approximately uniform power density across the beam. The heated thermoluminescent phosphor emits a visible or otherwise detectable luminescent emission which is measured as an indication of the radiation exposure of the thermoluminscent phosphors. Also disclosed are preferred signal processing and control circuits including one system using a digital computer. Also disclosed are time-profiled laser power cycles for pre-anneal, read and post-anneal treatment of phosphors.

High-brightness and high-color purity red-emitting Ca3Lu(AlO)3(BO3)4:Eu3+ phosphors with internal quantum efficiency close to unity for near-ultraviolet-based white-light-emitting diodes.

PubMed

Huang, Xiaoyong; Wang, Shaoying; Li, Bin; Sun, Qi; Guo, Heng

2018-03-15

In this work, we reported on high-brightness Eu 3+ -activated Ca 3 Lu(AlO) 3 (BO 3 ) 4 (CLAB) red-emitting phosphors. Under 397 nm excitation, the CLAB:Eu 3+ phosphors showed intense red emissions at around 621 nm with CIE coordinates of (0.657, 0.343). The optimal doping concentration of Eu 3+ ions was found to be 30 mol. %, and the CLAB:0.3Eu 3+ sample possessed high-color purity of 93% and ultra-high internal quantum efficiency as great as 98.5%. Importantly, the CLAB:0.3Eu 3+ also had good thermal stability. Finally, a white-light-emitting diode (WLED) lamp with good color-rendering index was fabricated by using a 365 nm ultraviolet chip and the phosphor blends of CLAB:0.3Eu 3+ red-emitting phosphors, (Ba,Sr) 2 SiO 4 :Eu 2+ green-emitting phosphors, and BaMgAl 10 O 7 :Eu 2+ blue-emitting phosphors.

Water Quality of the Upper Delaware Scenic and Recreational River and Tributary Streams, New York and Pennsylvania

USGS Publications Warehouse

Siemion, Jason; Murdoch, Peter S.

2010-01-01

Water-quality samples were collected from the Upper Delaware Scenic and Recreational River (UPDE) and its tributaries during the period October 1, 2005, to September 30, 2007, to document existing water quality, determine relations between land use and water quality, and identify areas of water-quality concern. A tiered water-quality monitoring framework was used, with the tiers consisting of intensively sampled sites, gradient sites representing the range of land uses present in the basin, and regional stream-survey sites. Median nitrate and total phosphorous concentrations were 1.15 and 0.01 mg/L (milligrams per liter) for three sites on the mainstem Delaware River, 1.27 and 0.009 mg/L for the East Branch Delaware River, 2.04 and 0.01 mg/L for the West Branch Delaware River, and 0.68 and 0.006 mg/L for eight tributaries that represent the range of land uses resent in the basin, respectively. The percentage of agricultural land varied by basin from 0 to 30 percent and the percentage of suburbanization varied from 0 to 17 percent. There was a positive correlation between the percentage of agricultural land use in a basin and observed concentrations of acid neutralizing capacity, calcium, potassium, nitrate, and total dissolved nitrogen, whereas no correlation between the percentage of suburbanization and water quality was detected. Results of stream surveys showed that nitrate concentrations in 55 to 65 percent of the UPDE Basin exceeded the nitrate reference condition and a suggested water-quality guideline for ecological impairment in New York State (0.98 mg/L) during the spring. Many of the affected parts of the basin were more than 90 percent forested and showed signs of episodic acidification, indicating that the long-term effects of acid deposition play a role in the high nitrate levels. Nitrate concentrations in 75 percent of samples collected from agricultural sites exceeded the suggested nitrate water-quality guideline for ecological impairment. Concentrations of nitrate and total phosphorous in samples collected from agricultural sites also were twice and 25 percent higher than those in samples from reference sites, respectively.

Comparison of microleakage on one composite etched with phosphoric acid or a combination of phosphoric and hydrofluoric acids and bonded with several different systems.

PubMed

Szep, Susanne; Langner, Nicole; Bayer, Silja; Börnichen, Diana; Schulz, Christoph; Gerhardt, Thomas; Schriever, Anette; Becker, Joachim; Heidemann, Detlef

2003-02-01

There are no data available on whether or to what extent hydrofluoric acid affects the marginal integrity of dentin-bonded composite restorations when it is used instead of phosphoric acid in the total-etch technique. This in vitro study examined the etching effects of phosphoric acid versus a combination of phosphoric and hydrofluoric acid by evaluation of microleakage in a composite restoration bonded with different dentin adhesive systems. Extracted teeth (n = 90) containing 2 class II preparations, mesial occlusal (MO) and distal occlusal (DO) standarized (cervical margins in dentin) were perfused with Ringer solution and etched in 1 of 2 ways: with phosphoric acid only or with phosphoric combined with hydrofluoric acid. Different dentin bonding agents were then applied (Etch & Prime 3.0, Optibond Solo, Prime & Bond NT, Scotchbond 1, Syntac Single Component, or Syntac Sprint; (n = 15 for each etching material)). The preparations were restored with a hybrid composite (Herculite XRV) and submitted to 5000 thermocycles (5 degrees C to 55 degrees C) to simulate the in vivo situation. Microleakage was assessed with 2% methylene blue diffusion for 24 hours. Dye penetration was calculated as a percentage of the total length of the gingival margins of the preparation with light microscopy at original magnification x 32. The results were analyzed with the Kruskal-Wallis multiple comparison z-value assay (alpha = .05). Differences in dye penetration were significant, both as a function of the dentin adhesive and the conditioning mode applied. In the specimen groups conditioned with phosphoric acid, Optibond Solo (54% +/- 44%) and Syntac Sprint (74% +/- 39%) demonstrated the lowest penetration values. Higher values were obtained for Prime & Bond NT (81% +/- 34%), Scotchbond 1 (83% +/- 31%), Etch & Prime 3.0 (85% +/- 33%), and Syntac Single Component (95% +/- 16%), with no significant differences (alpha=.05) between specimen groups. The best results were obtained for Syntac Sprint (24% +/- 26% dye penetration) after conditioning with a mixture of phosphoric and hydrofluoric acid. The least favorable result was obtained for Optibond Solo (65% +/- 31%). It was significantly different from Prime & Bond NT (76% +/- 37%), Scotchbond 1 (85% +/- 29%), and Etch & Prime 3.0 (88% +/- 24%). Syntac Single Component (75% +/- 32%) was significantly different from Syntac Sprint. Syntac Single Component and Syntac Sprint exhibited significantly better results when conditioned with a combination of phosphoric acid and hydrofluoric acid than with phosphoric acid only. Within the limitations of this in vitro study, total-etching water-based (Syntac Single Component) and acetone-based (Syntac Sprint) bonding agents with a combination of phosphoric acid and hydrofluoric acid led to significant reductions (alpha=.05) in dye penetration compared to phosphoric acid conditioning only. Ethanol-based dentin bonding agents (Etch & Prime 3.0, Optibond Solo, and Scotchbond 1) were not significantly influenced by the type of conditioner used.

A promising red-emitting phosphor for white-light-emitting diodes prepared by a modified solid-state reaction

NASA Astrophysics Data System (ADS)

Ren, Fuqiang; Chen, Donghua

2010-02-01

Using urea, boric acid and polyethylene glycol (PEG) as auxiliary reagents, the novel red-emitting phosphors Ca 19Zn 2 (PO 4) 14:Eu 3+ have been successfully synthesized by a modified solid-state reaction. Thermogravimetric (TG) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence (PL) spectra were used to characterize the resulting phosphors. The dependence of the photoluminescence properties of Ca 19Zn 2 (PO 4) 14:Eu 3+ phosphors upon urea, boric acid and PEG concentration and the quadric-sintered temperature were investigated. Luminescent measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a red light with a peak wavelength of 616 nm. The material has potential application as a fluorescent material for ultraviolet light-emitting diodes (UV-LEDs).

Synthesis, energy transfer and luminescence properties of Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Renping, E-mail: jxcrp@163.com; Xu, Haidong; Luo, Wenjie

Graphical abstract: PL spectra of Ca{sub 2}MgWO{sub 6}:Sm{sup 3+} and Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphors with excitation at 407 nm, and the corresponding CIE chromaticity diagram and chromaticity coordinates. - Highlights: • Novel Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphor is synthesized by solid-state reaction method in air. • Emission intensity of Ca{sub 2}MgWO{sub 6}:Sm{sup 3+} phosphor is enhanced ∼2 times after co-doped Bi{sup 3+} ion. • Charge compensation and energy transfer may be explained via luminescence properties. • Luminous mechanism is analyzed by energy level diagrams of WO{sub 6}{sup 6−} group, Sm{sup 3+} and Bi{sup 3+} ions.more » - Abstract: Novel Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphor is synthesized by solid-state reaction method in air. Host Ca{sub 2}MgWO{sub 6} with excitation 300 nm emits blue light. Ca{sub 2}MgWO{sub 6}:Bi{sup 3+} phosphor with excitation 300 and 338 nm emits yellow light. Ca{sub 2}MgWO{sub 6}:Sm{sup 3+} phosphor with excitation 300 nm exhibits tunable emission from blue to red light by increasing Sm{sup 3+} doping concentration from 0 to 8 mol%, however, only emits red light with excitation 407 nm. Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphor with excitation 300 and 338 nm emits red light. The optimal Sm{sup 3+} doping concentration is ∼5 mol% in Ca{sub 2}MgWO{sub 6}:Sm{sup 3+} phosphor. After Bi{sup 3+} ion is co-doped, luminescence properties of Ca{sub 2}MgWO{sub 6}:Sm{sup 3+} phosphor can be improved obviously because of Bi{sub 2}O{sub 3} as fluxing agent role and energy transfer from Bi{sup 3+} to Sm{sup 3+} ions. The possible luminous mechanism of Ca{sub 2}MgWO{sub 6}:Sm{sup 3+}, Bi{sup 3+} phosphor is analyzed and explained by simplified energy level diagrams of WO{sub 6}{sup 6−} group, Bi{sup 3+} and Sm{sup 3+} ions.« less

Synthesis and Luminescence Properties of Blue Na(Sr0.97-xCa(x))PO4:0.03Eu2+ Phosphors for White Light Emitting Diode Applications.

PubMed

Hakeem, D A; Park, K

2015-07-01

The crystal structure and luminescence properties of Na(Sr0.97-xCax)PO4:0.03Eu2+ (0 < x < 1.0) phosphors were studied, depending on the Ca2+ concentration. All the Na(Sr0.97-xCax)PO4:0.03Eu2+ phosphors had a hexagonal crystal structure. The excitation spectra of the prepared phosphors showed a broad band ranging from 250 to 420 nm, which arises due to the 4f-5d transitions of Eu2+ ions. Upon the excitation of 334 nm wavelength, the emission spectra showed a broad blue band ranging from 400 to 700 nm peaking at 450 nm. Among the prepared phosphors, the Na(Sr0.72Ca0.25)PO4:0.03Eu2+ showed the strongest emission intensity and could be applied as a blue emitting phosphor for UV-based w-LEDs.

Spectral downshifting from blue to near infer red region in Ce3+-Nd3+ co-doped YAG phosphor

NASA Astrophysics Data System (ADS)

Sawala, N. S.; Omanwar, S. K.

2016-07-01

The YAG phosphors co-doped with Ce3+-Nd3+ ions by varying concentration of Nd3+ ion from 1 mol% to 15 mol% were successfully synthesized by conventional solid state reaction method. The phosphors were characterized by powder X-ray powder diffraction (XRD) and surface morphology was studied by scanning electronic microscope (SEM). The photoluminescence (PL) properties were studied in near infra red (NIR) and ultra violet visible (UV-VIS) region. The synthesized phosphors can convert a blue region photon (453 nm) into photons of NIR region (1063 nm). The energy transfer (ET) process was studied by time decay curve and PL spectra. The theoretical value of energy transfer efficiency (ETE) was calculated from time decay luminescence measurement and the maximum efficiency approached up to 82.23%. Hence this phosphor could be prime candidate as a downshifting (DS) luminescent convertor (phosphor) in front of crystalline silicon solar cell (c-Si) panels to reduce thermalization loss in the solar cells.

High power laser-driven ceramic phosphor plate for outstanding efficient white light conversion in application of automotive lighting

PubMed Central

Song, Young Hyun; Ji, Eun Kyung; Jeong, Byung Woo; Jung, Mong Kwon; Kim, Eun Young; Yoon, Dae Ho

2016-01-01

We report on Y3Al5O12: Ce3+ ceramic phosphor plate (CPP) using nano phosphor for high power laser diode (LD) application for white light in automotive lighting. The prepared CPP shows improved luminous properties as a function of Ce3+ concentration. The luminous properties of the Y3Al5O12: Ce3+ CPP nano phosphor are improved when compared to the Y3Al5O12: Ce3+ CPP with bulk phosphor, and hence, the luminous emittance, luminous flux, and conversion efficiency are improved. The Y3Al5O12: Ce3+ CPP with an optimal Ce3+ content of 0.5 mol % shows 2733 lm/mm2 value under high power blue radiant flux density of 19.1 W/mm2. The results indicate that Y3Al5O12: Ce3+ CPP using nano phosphor can serve as a potential material for solid-state laser lighting in automotive applications. PMID:27502730

High power laser-driven ceramic phosphor plate for outstanding efficient white light conversion in application of automotive lighting.

PubMed

Song, Young Hyun; Ji, Eun Kyung; Jeong, Byung Woo; Jung, Mong Kwon; Kim, Eun Young; Yoon, Dae Ho

2016-08-09

We report on Y3Al5O12: Ce(3+) ceramic phosphor plate (CPP) using nano phosphor for high power laser diode (LD) application for white light in automotive lighting. The prepared CPP shows improved luminous properties as a function of Ce(3+) concentration. The luminous properties of the Y3Al5O12: Ce(3+) CPP nano phosphor are improved when compared to the Y3Al5O12: Ce(3+) CPP with bulk phosphor, and hence, the luminous emittance, luminous flux, and conversion efficiency are improved. The Y3Al5O12: Ce(3+) CPP with an optimal Ce(3+) content of 0.5 mol % shows 2733 lm/mm(2) value under high power blue radiant flux density of 19.1 W/mm(2). The results indicate that Y3Al5O12: Ce(3+) CPP using nano phosphor can serve as a potential material for solid-state laser lighting in automotive applications.

Proliferation of dinoflagellates in Kochi estuary, Kerala.

PubMed

Kumar, M Ratheesh; Vishnu, S Raj; Sudhanandh, V S; Faisal, A K; Shibu, R; Vimexen, V; Ajmal, K; Aneesh, K S; Antony, Sibin; Krishnan, Anoop K

2014-09-01

Phytoplankton community structure and dynamics of Kochi estuary (bar mouth) have been studied seasonally. Three seasonal samplings namely pre-monsoon, monsoon and post-monsoon were made, and a wide variation was observed in phytoplankton community with respect to nutrients and other physicochemical parameters. Contrary to other seasons, dinoflagellate cell density increased during pre-monsoon season though species diversity was less pronounced (D > 0.15). Peridinium oceanicum was the dominant dinoflagellate during pre-monsoon season. Significant fluctuation in three principal nutrients namely total nitrogen, total phosphorous and silicate were observed during pre-monsoon (TP < 1.8 micromol l(-1), TN > 40 micromol l(-1) and SiO4 < 20 micromol l(-1)) season as compared to monsoon season (TP > 3.20 micromol l(-1), TN < 20 micromol l(-1) and SiO4 > 27 micromol l(-1)). Salinity values were also found to be high during pre-monsoon ( > 25 psu). Study suggests that variation in salinity and nutrient concentration during transition of seasons could result in succession of species, thereby causing change in phytoplankton community structure. High salinity and nitrogen values along with low values of silicate and phosphorous resulted in proliferation of dinoflagellates during pre-monsoon season.

Investigation on optical band gap, photoluminescence properties and concentration quenching mechanism of Pb1 - x Tb3 +xWO4 green-emitting phosphors

NASA Astrophysics Data System (ADS)

Chanu, Thokchom Taru Taru; Rajmuhon Singh, N.

2018-02-01

A series of monophasic Tb3 + (2, 5, 7, 10 and 15 at%) doped PbWO4 phosphors were successfully prepared via hydrothermal method. X-ray diffraction patterns revealed that the prepared samples possess a high crystallinity with tetragonal scheelite-type structure. FT-IR and Raman analysis exhibited a Wsbnd O stretching peak of WO42 - group, which is also related to the scheelite structure. UV-visible diffuse reflectance spectra indicated a reduction in the optical band gap with the replacement of Pb2 + by Tb3 + ions. The presence of strong and intense emission peaks characteristic of Tb3 + with the dominant peak at 545 nm (green, 5D4 → 7F5 transition) under UV irradiation at 320 nm demonstrated an efficient energy transfer from the host to Tb3 + ions. Using Van Uitert's model, the concentration quenching mechanism between Tb3 + ions in PbWO4:Tb3 + phosphor was attributed to a dipole-dipole interaction and the critical distance was determined to be 12 Å. The decay lifetimes and CIE chromaticity co-ordinates of PbWO4:Tb3 + phosphors were also investigated in detail. These prepared materials might serve as a potential phosphor for LED applications.

Estimation of mercury amount in the components of spent U-type lamp.

PubMed

Rhee, Seung-Whee

2017-05-01

Spent U-type lamps are strongly encouraged to be separately managed in Korea, because U-type lamps are categorized as a household waste and thereby could not be managed properly. Determination of mercury amount in the components of U-type lamp, such as plastics, glass tube and phosphor powder from 3 U-type lamp manufacturers (A, B and C), is carried out to estimate the mercury content in spent U-type lamps. Regardless of lamp manufacturers, the portion of mercury in phosphor powder was higher than 90%, but that in plastics and others was less than 1%. At an air flow rate of 1.0 L/min, the range of the initial mercury concentration in vapor phase for U-type lamp was between 849 and 2076 µg/m 3 from 3 companies. The estimated mercury amount in vapor phase of U-type lamp was in the range from 0.206 mg for company A to 0.593 mg for company B. And the portion of mercury in vapor phase in the total amount of mercury was estimated in the range from 3.0% for company A to 6.7% for company B. Hence, it is desirable to get rid of mercury from phosphor powder in order to perform U-type lamps recycling.

The synthesis and luminescence properties of a novel red-emitting phosphor: Eu3+-doped Ca9La(PO4)7

NASA Astrophysics Data System (ADS)

Liang, Zehui; Mu, Zhongfei; Wang, Qiang; Zhu, Daoyun; Wu, Fugen

2017-10-01

A series of novel red-emitting phosphors Ca9La1- x (PO4)7: xEu3+ were synthesized by high-temperature solid state reactions. The photoluminescence excitation and photoluminescence spectra of these phosphors were investigated in detail. O2--Eu3+ charge transfer band peaking at about 261 nm is dominant in the PLE spectra of Eu3+-doped Ca9La(PO4)7, indicating that the phosphors are suitable for tricolor fluorescent lamps. The phosphors also show a good absorption in near ultraviolet (around 395 nm) and blue (around 465 nm) spectral region, which indicates that it can be pumped with NUV and blue chips for white light-emitting diodes. The transition of 5D0 → 7F2 of Eu3+ in this lattice can emit bright red light. Ca9La(PO4)7 could accommodate a large amount of Eu3+ with an optimal concentration of 60 mol%. The dipole-dipole interaction between Eu3+ is the dominant mechanism for concentration quenching of Eu3+. The calculated color coordinates lie in red region ( x = 0.64, y = 0.36), which is close to Y2O3: 0.05Eu3+ ( x = 0.65, y = 0.34). The integral emission intensity of Ca9La0.4(PO4)7: 0.6Eu3+ is 1.9 times stronger than that of widely used commercial red phosphor Y2O3: 0.05Eu3+. All these results indicate that Eu3+-doped Ca9La(PO4)7 is a promising red-emitting phosphor which can be used in tricolor fluorescent lamps and white light-emitting diodes.

Study on TL and OSL characteristics of indigenously developed CaF 2:Mn phosphor

NASA Astrophysics Data System (ADS)

Bakshi, A. K.; Dhabekar, Bhushan; Rawat, N. S.; Singh, S. G.; Joshi, V. J.; Kumar, Vijay

2009-02-01

CaF 2:Mn phosphor is known for its high thermoluminescent sensitivity and dose linearity up to few kGy. In the present study CaF 2 phosphor with different concentration of Mn dopant was prepared and was characterized through different techniques. The phosphor was prepared through chemical root using CaCO 3, HF acid and MnCl 2 as raw materials following co-precipitation method. TL sensitivity of the prepared phosphor was compared with other well established phosphors used for radiation dosimetry. It was found that the TL sensitivity is higher by a factor of 10 with respect to LiF:Mg, Ti, TLD-100 and half to that of CaSO 4:Dy (0.05 mol%) phosphor. X-ray diffraction, TL emission spectrum and ESR spectrum taken of the prepared phosphor confirms the crystal structure, Mn 2+ emission and incorporation Mn in the crystal, respectively. No significant fading of the dosimetric peak was observed of the prepared phosphor for a storage period of 45 days. The dose linearity of the phosphor was found to be in the range of 50 Gy-3 kGy within an uncertainty of about 10%. An attempt was made to determine the kinetic parameters of TL glow curve and the parameters related to optically stimulated luminescence. In view of its long range of dose linearity, it can be used for the dosimetry of commercial irradiator generally used for the irradiation of food and grains in our country.

Determination of mercury distribution inside spent compact fluorescent lamps by atomic absorption spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rey-Raap, Natalia; Gallardo, Antonio, E-mail: gallardo@emc.uji.es

Highlights: Black-Right-Pointing-Pointer New treatments for CFL are required considering the aim of Directive 202/96/CE. Black-Right-Pointing-Pointer It is shown that most of the mercury introduced into a CFL is in the phosphor powder. Black-Right-Pointing-Pointer Experimental conditions for microwave-assisted sample digestion followed by AAS measurements are described. Black-Right-Pointing-Pointer By washing the glass it is possible to reduce the concentration below legal limits. - Abstract: In this study, spent compact fluorescent lamps were characterized to determine the distribution of mercury. The procedure used in this research allowed mercury to be extracted in the vapor phase, from the phosphor powder, and the glass matrix.more » Mercury concentration in the three phases was determined by the method known as cold vapor atomic absorption spectrometry. Median values obtained in the study showed that a compact fluorescent lamp contained 24.52 {+-} 0.4 ppb of mercury in the vapor phase, 204.16 {+-} 8.9 ppb of mercury in the phosphor powder, and 18.74 {+-} 0.5 ppb of mercury in the glass matrix. There are differences in mercury concentration between the lamps since the year of manufacture or the hours of operation affect both mercury content and its distribution. The 85.76% of the mercury introduced into a compact fluorescent lamp becomes a component of the phosphor powder, while more than 13.66% is diffused through the glass matrix. By washing and eliminating all phosphor powder attached to the glass surface it is possible to classified the glass as a non-hazardous waste.« less

Addition of Grape Seed Extract Renders Phosphoric Acid a Collagen-stabilizing Etchant.

PubMed

Liu, Y; Dusevich, V; Wang, Y

2014-08-01

Previous studies found that grape seed extract (GSE), which is rich in proanthocyanidins, could protect demineralized dentin collagen from collagenolytic activities following clinically relevant treatment. Because of proanthocyanidin's adverse interference to resin polymerization, it was believed that GSE should be applied and then rinsed off in a separate step, which in effect increases the complexity of the bonding procedure. The present study aimed to investigate the feasibility of combining GSE treatment with phosphoric acid etching to address the issue. It is also the first attempt to formulate collagen-cross-linking dental etchants. Based on Fourier-transformed infrared spectroscopy and digestion assay, it was established that in the presence of 20% to 5% phosphoric acid, 30 sec of GSE treatment rendered demineralized dentin collagen inert to bacterial collagenase digestion. Based on this positive result, the simultaneous dentin etching and collagen protecting of GSE-containing phosphoric acid was evaluated on the premise of a 30-second etching time. According to micro-Raman spectroscopy, the formulation containing 20% phosphoric acid was found to lead to overetching. Based on scanning and transmission electronic microscopy, this same formulation exhibited unsynchronized phosphoric acid and GSE penetration. Therefore, addition of GSE did render phosphoric acid a collagen-stabilizing etchant, but the preferable phosphoric acid concentration should be <20%. © International & American Associations for Dental Research.

Structure and photoluminescence properties of Ba2-xSi4O10:2xSm3+

NASA Astrophysics Data System (ADS)

Ramteke, D. D.; Swart, H. C.

2018-04-01

We investigated the structure and photoluminescence properties of novel Ba2-xSi4O10:2xSm3+ phosphor prepared by the solid state reaction method. In the prepared phosphor the high temperature monoclinic phase was dominant over the low temperature orthorhombic phase. The shifting of the X-ray diffraction peaks with the Sm3+ ion addition was explained on the basis of the refinement results. The photoluminescence study showed that on excitation with 402 nm the phosphor emitted at 560 nm, 600 nm and 645 nm which corresponds to the 4G5/2→4H5/2, 4G5/2→4H7/2 and 4G5/2→4H9/2 transitions, respectively. Concentration quenching effect was also observed in the prepared phosphor. CIE chromaticity coordinates showed that the phosphor can be further developed for display applications.

Interfacial characteristics of an epoxy composite reinforced with phosphoric acid-functionalized Kevlar fibers

NASA Astrophysics Data System (ADS)

Li, J.; Xia, Y. C.

2010-07-01

A Kevlar fiber was functionalized with the phosphoric acid (PA) of different concentrations. The surface characteristics of the fiber were examined by using the X-ray photoelectron spectroscopy. It was found that the PA functionalization considerably increased the bond strength between the Kevlar fiber and an epoxy matrix.

Controllable upconversion luminescence and temperature sensing behavior in NaGdF4:Yb3+/Ho3+/Ce3+ nano-phosphors

NASA Astrophysics Data System (ADS)

Pang, Tao; Wang, Jiajun

2018-01-01

The hexagonal NaGdF4:Yb3+/Ho3+/Ce3+ nano-phosphors are synthesized by a hydrothermal method. Under 980 nm excitation, the phosphor emits green, red and far-red light in the visible wavelength region, corresponding to the 5S2/5F4 → 5I8, 5F5 → 5I8 and 5S2/5F4 → 5I7 transitions of Ho3+ ions, respectively. When adjusting the Ce3+ concentration from 0% to 16%, the dominant wavelength shifts ˜43 nm toward the longer wavelength. Two cross-relaxation processes between Ho3+ and Ce3+ are responsible for the change in chromaticity. Also, the ability of the Ce3+ concentration to regulate the luminescence color depends on the pumping power and temperature of samples. More interestingly, the phosphors are potentially applicable as the optical thermometric materials. In the case of 16% Ce3+ doping, the maximum sensitivity (0.1446 K-1) about 4-35 times as high as the reported values of several typical thermometric materials is obtained.

Synergistic dynamics of nitrogen and phosphorous influences lipid productivity in Chlorella minutissima for biodiesel production.

PubMed

Arora, Neha; Patel, Alok; Pruthi, Parul A; Pruthi, Vikas

2016-08-01

The study synergistically optimized nitrogen and phosphorous concentrations for attainment of maximum lipid productivity in Chlorella minutissima. Nitrogen and phosphorous limited cells (N(L)P(L)) showed maximum lipid productivity (49.1±0.41mg/L/d), 1.47 folds higher than control. Nitrogen depletion resulted in reduced cell size with large sized lipid droplets encompassing most of the intracellular space while discrete lipid bodies were observed under nitrogen sufficiency. Synergistic N/P starvations showed more prominent effect on photosynthetic pigments as to individual deprivations. Phosphorous deficiency along with N starvation exhibited 17.12% decline in carbohydrate while no change in nitrogen sufficient cells were recorded. The optimum N(L)P(L) concentration showed balance between biomass and lipid by maintaining intermediate cell size, pigments, carbohydrate and proteins. FAME profile showed C14-C18 carbon chains in N(L)P(L) cells with biodiesel properties comparable to plant oil methyl esters. Hence, synergistic N/P limitation was effective for enhancing lipid productivity with reduced consumption of nutrients. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electrocatalysis of fuel cell reactions: Investigation of alternate electrolytes

NASA Technical Reports Server (NTRS)

Chin, D. T.; Hsueh, K. L.; Chang, H. H.

1984-01-01

Oxygen reduction and transport properties of the electrolyte in the phosphoric acid fuel cell are studied. The areas covered were: (1) development of a theoretical expression for the rotating ring disk electrode technique; (2) determination of the intermediate reaction rate constants for oxygen reduction on platinum in phosphoric acid electrolyte; (3) determination of oxygen reduction mechanism in trifluoreomethanesulfonic acid (TFMSA) which was considered as an alternate electrolyte for the acid fuel cells; and (4) the measurement of transport properties of the phosphoric acid electrolyte at high concentrations and temperatures.

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

SrMoO4:Er3+-Yb3+ upconverting phosphor for photonic and forensic applications

NASA Astrophysics Data System (ADS)

Soni, Abhishek Kumar; Rai, Vineet Kumar

2016-08-01

The Er3+-Yb3+ codoped strontium molybdate (SrMoO4) phosphors have been synthesized via chemical co-precipitation method by adding ammonium hydroxide as a base reagent. The phase, crystal structure and formation of spindle-like particles present in the prepared phosphors have been recognized by using the X-ray powder diffraction (XRPD) and Field emission scanning electron microscopy (FE-SEM) techniques. The Fourier transform infrared (FTIR) spectroscopy of the developed phosphors has been analyzed to mark the different functional groups present in synthesized phosphors. The multicolour upconversion emissions observed upon excitation with 980 nm and 808 nm laser diode have been explained on the basis of dopants ions concentration, pump power dependence, energy level structure and decay curve analysis. The colour co-ordinate study confirmed that the codoped phosphor emits non-tunable green colour when excited with the 980 nm laser diode, whereas it shows the colour tunability from yellow to green region upon excitation with the 808 nm laser diode. The applicability of non-tunable green colour emission has been demonstrated in the security ink and latent finger print detection. This shows the utility of the developed phosphors in the photonic and forensic applications.

The effects of boric acid and phosphoric acid on the compressive strength of glass-ionomer cements.

PubMed

Prentice, Leon H; Tyas, Martin J; Burrow, Michael F

2006-01-01

Both boric acid (H3BO3) and phosphoric acid (H3PO4) are components of dental cements, commonly incorporated into glass (as ingredients in the melt) and occasionally added to the powder or liquid components. This study investigated the effect of boric acid addition to an experimental glass-ionomer powder and the effect of phosphoric acid addition to a glass-ionomer liquid on the 24-h compressive strength. Boric acid powder was added in various concentrations to an experimental glass-ionomer powder and, separately, phosphoric acid was added to an experimental glass-ionomer liquid. Powders and liquids were dosed into capsules at various powder:liquid ratios and cements thus formed were assessed for 24-h compressive strength. Incorporation of boric acid in glass-ionomer powder resulted in a pronounced decrease (p < 0.05 at 1% boric acid) in compressive strength. Addition of phosphoric acid produced initially stronger cements (up to 13% increase at 1% phosphoric acid) before also declining. The incorporation of less than 2% w/w phosphoric acid in glass-ionomer liquids may improve cement strengths without compromising clinical usefulness. The incorporation of boric acid in glass-ionomer cements is contraindicated.

Characterization and luminescence properties of Sr3Gd): Sm3+ orange-red phosphor

NASA Astrophysics Data System (ADS)

Yang, Zaifa; Xu, Denghui; Sun, Jiayue; Sun, Yumei; Du, Haiyan

2015-10-01

Reddish-orange emitting phosphors, Sr3Gd): Sm3+, were successfully synthesized by a conventional solid-state reaction. The crystal structure of the phosphors was characterized by x-ray diffraction. The excitation spectra and emission spectra were utilized to characterize the luminescence properties of the as-prepared phosphors. The results show that the phosphor consisted of some sharp emission peaks of Sm3+ ions centered at 564, 600, 647, and 707 nm, respectively. The critical distance of Sr3Gd0.93): 0.07Sm3+ was calculated to be 19.18 Å and the lifetime value of the sample was 1.63 ms. The band gap of Sr3Gd) was estimated to be about 2.74 eV from the diffuse reflection spectrum. The optimum doping concentration is 7 mol. % and the quenching occurs via dipole-dipole interaction according to Dexter's theory. The Commission Internationale de L'Eclairage value of Sr3Gd): Sm3+ phosphors presented that it has high color purity. These results indicated that the Sr3Gd): Sm3+ may be a promising reddish-orange emitting phosphor for cost-effective near ultraviolet white light-emitting diodes.

The Levels and Distribution of TN, TP and TOC in the South China Sea

NASA Astrophysics Data System (ADS)

Wang, H.; Han, D.

2012-04-01

The marine biogeochemistries of carbon, nitrogen and phosphorous have come under increased scrutiny because of their close involvement in climate change and coastal eutrophication. The South China Sea is unique in that located in a subtropical zone, and therefore represents an important regime for biogeochemical studies. However, to our knowledge, few data are available for total nitrogen (TN), total phosphorous (TP) and total organic carbon (TOC) in South Sea, China. The present study aims to contribute to the knowledge of their status through investigating the level and distribution of TN, TP and TOC in South China Sea. A total of 108 seawater samples of 11 sites in south sea, china were collected during August 29- September 4, 2006. An automated and simultaneous method for determination of TN and TOC was applied to all seawater samples. The combined system allowed simultaneous determination for TOC and TN in the same sample using a single injection and provided low detection limits and excellent linear ranges for both TOC and TN. The risk of contamination has been remarkably reduced due to the minimal sample manipulation and automated analyses. And quantitative analyses of TP in seawater were accomplished by a typical chemical method. Concentration ranges of TN and TP were 0.06-0.67, and 0.003-0.071 mg/L, respectively, as well as that of TOC were 0.23-2.51mg/L. The values of TN and TP showed that the status of nutrition is relatively better in south china sea than other marine areas. Moreover, the upright change trend of TN concentration level as well as TP and TOC according to the experimental results at the total 11 sites are simultaneity studied. The concentration of TN initial increases with the increasing of the depth, later the value becomes almost constant. In contrast, the concentration of TOC reduces with the increasing of the depth, later the value becomes almost unchangeable. Compared with the trend of TN and TOC, that of TP appears relatively stable. Thus, TP could be regarded as the key factor about eutrophication. This work should provide some useful information to better understand the environmental status of south china sea. Keywords: Concentration level, distribution, TN, TP, TOC, South China Sea. Acknowledgments The work was supported by The National Natural Science Foundation of China (No. 40976050), and the National Public Benefit (Ocean) Research Foundation of China (201105013).

Luminescence study of Eu(3+) doped Li6 Y(BO3 )3 phosphor for solid-state lighting.

PubMed

Yawalkar, Mrunal M; Zade, G D; Dabre, K V; Dhoble, S J

2016-06-01

In this study, Li6 Y1-x Eux (BO3 )3 phosphor was successfully synthesized using a modified solid-state diffusion method. The Eu(3+) ion concentration was varied at 0.05, 0.1, 0.2, 0.5 and 1 mol%. The phosphor was characterized for phase purity, morphology, luminescent properties and molecular transmission at room temperature. The XRD pattern suggests a result closely matching the standard JCPDS file (#80-0843). The emission and excitation spectra were followed to discover the luminescence traits. The excitation spectra indicate that the current phosphor can be efficiently excited at 395 nm and at 466 nm (blue light) to give emission at 595 and 614 nm due to the (5) D0  → (7) Fj transition of Eu(3+) ions. Concentration quenching was observed at 0.5 mol% Eu(3+) in the Li6 Y1-x Eux (BO3 )3 host lattice. Strong red emission with CIE chromaticity coordinates of phosphor is x = 0.63 and y = 0.36 achieved with dominant red emission at 614 nm the (5) D0  → (7)  F2 electric dipole transition of Eu(3+) ions. The novel Li6 Y1-x Eux (BO3 )3 phosphor may be a suitable red-emitting component for solid-state lighting using double-excited wavelengths, i.e. near-UV at 395 nm and blue light at 466 nm. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Sr(1.7)Zn(0.3)CeO4: Eu3+ novel red-emitting phosphors: synthesis and photoluminescence properties.

PubMed

Li, Haifeng; Zhao, Ran; Jia, Yonglei; Sun, Wenzhi; Fu, Jipeng; Jiang, Lihong; Zhang, Su; Pang, Ran; Li, Chengyu

2014-03-12

A series of novel red-emitting Sr1.7Zn0.3CeO4:Eu(3+) phosphors were synthesized through conventional solid-state reactions. The powder X-ray diffraction patterns and Rietveld refinement verified the similar phase of Sr1.7Zn0.3CeO4:Eu(3+) to that of Sr2CeO4. The photoluminescence spectrum exhibits that peak located at 614 nm ((5)D0-(7)F2) dominates the emission of Sr1.7Zn0.3CeO4:Eu(3+) phosphors. Because there are two regions in the excitation spectrum originating from the overlap of the Ce(4+)-O(2-) and Eu(3+)-O(2-) charge-transfer state band from 200 to 440 nm, and from the intra-4f transitions at 395 and 467 nm, the Sr1.7Zn0.3CeO4:Eu(3+) phosphors can be well excited by the near-UV light. The investigation of the concentration quenching behavior, luminescence decay curves, and lifetime implies that the dominant mechanism type leading to concentration quenching is the energy transfer among the nearest neighbor or next nearest neighbor activators. The discussion about the dependence of photoluminescence spectra on temperature shows the better thermal quenching properties of Sr1.7Zn0.3CeO4:0.3Eu(3+) than that of Sr2CeO4:Eu(3+). The experimental data indicates that Sr1.7Zn0.3CeO4:Eu(3+) phosphors have the potential as red phosphors for white light-emitting diodes.

High color rendering index of remote-type white LEDs with multi-layered quantum dot-phosphor films and short-wavelength pass dichroic filters

NASA Astrophysics Data System (ADS)

Yoon, Hee Chang; Oh, Ji Hye; Do, Young Rag

2014-09-01

This paper introduces high color rendering index (CRI) white light-emitting diodes (W-LEDs) coated with red emitting (Sr,Ca)AlSiN3:Eu phosphors and yellowish-green emitting AgIn5S8/ZnS (AIS/ZS) quantum dots (QDs) on glass or a short-wavelength pass dichroic filter (SPDF), which transmit blue wavelength regions and reflect yellow wavelength regions. The red emitting (Sr,Ca)AlSiN3:Eu phosphor film is coated on glass and a SPDF using a screen printing method, and then the yellowish-green emitting AIS/ZS QDs are coated on the red phosphor (Sr,Ca)AlSiN3:Eu film-coated glass and SPDF using the electrospray (e-spray) method.To fabricate the red phosphor film, the optimum amount of phosphor is dispersed in a silicon binder to form a red phosphor paste. The AIS/ZS QDs are mixed with dimethylformamide (DMF), toluene, and poly(methyl methacrylate) (PMMA) for the e-spray coating. The substrates are spin-coated with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) to fabricate a conductive surface. The CRI of the white LEDs is improved through inserting the red phosphor film between the QD layer and the glass substrate. Furthermore, the light intensities of the multi-layered phosphor films are enhanced through changing the glass substrate to the SPDF. The correlated color temperatures (CCTs) vary as a function of the phosphor concentration in the phosphor paste. The optical properties of the yellowish-green AIS/ZS QDs and red (Sr,Ca)AlSiN3:Eu phosphors are characterized using photoluminescence (PL), and the multi-layered QD-phosphor films are measured using electroluminescence (EL) with an InGaN blue LED (λmax = 450 nm) at 60 mA.

Corrosion of graphite composites in phosphoric acid fuel cells

NASA Technical Reports Server (NTRS)

Christner, L. G.; Dhar, H. P.; Farooque, M.; Kush, A. K.

1986-01-01

Polymers, polymer-graphite composites and different carbon materials are being considered for many of the fuel cell stack components. Exposure to concentrated phosphoric acid in the fuel cell environment and to high anodic potential results in corrosion. Relative corrosion rates of these materials, failure modes, plausible mechanisms of corrosion and methods for improvement of these materials are investigated.

A Technique for the Microstructural Examination of Polycrystalline Graphites

DTIC Science & Technology

1959-02-01

dichromate in concentrated phosphoric acid . This etchsnt reacted quite readily with the graphite surface, yet at a rate that was...formation of lamellar compounds, and carbide formation at high temperatues . Of the three classes of reaction, oxidation seems to...reagents and conditions were directed toward preliminary studies of such chemical oxidants as potassium dichromate-phosphoric acid mixtures

Investigation on optical band gap, photoluminescence properties and concentration quenching mechanism of Pb1-x Tb3+xWO4 green-emitting phosphors.

PubMed

Chanu, Thokchom Taru Taru; Rajmuhon Singh, N

2018-02-15

A series of monophasic Tb 3+ (2, 5, 7, 10 and 15at%) doped PbWO 4 phosphors were successfully prepared via hydrothermal method. X-ray diffraction patterns revealed that the prepared samples possess a high crystallinity with tetragonal scheelite-type structure. FT-IR and Raman analysis exhibited a WO stretching peak of WO 4 2- group, which is also related to the scheelite structure. UV-visible diffuse reflectance spectra indicated a reduction in the optical band gap with the replacement of Pb 2+ by Tb 3+ ions. The presence of strong and intense emission peaks characteristic of Tb 3+ with the dominant peak at 545nm (green, 5 D 4 → 7 F 5 transition) under UV irradiation at 320nm demonstrated an efficient energy transfer from the host to Tb 3+ ions. Using Van Uitert's model, the concentration quenching mechanism between Tb 3+ ions in PbWO 4 :Tb 3+ phosphor was attributed to a dipole-dipole interaction and the critical distance was determined to be ~12Å. The decay lifetimes and CIE chromaticity co-ordinates of PbWO 4 :Tb 3+ phosphors were also investigated in detail. These prepared materials might serve as a potential phosphor for LED applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Ultratrace determination of total and available cyanides in industrial wastewaters through a rapid headspace-based sample preparation and gas chromatography with nitrogen phosphorous detection analysis.

PubMed

Marton, Daniele; Tapparo, Andrea; Di Marco, Valerio B; Repice, Carla; Giorio, Chiara; Bogialli, Sara

2013-07-26

A new analytical method for the determination of both available (free and weak acid dissociable, WAD) and total cyanides in industrial wastewaters has been developed. It is based on the static headspace (HS) sampling procedure followed by a GC separation and the selective nitrogen-phosphorous detection (NPD), in which different thermal treatment allows the speciation of total and available cyanides. Detection limits (0.5μg/L), recovery (84.7-114.6% for free and 76.8-121.5% for total cyanides) and precision (5% at 5μg/L), evaluated on both real and synthetic samples, were fit-for-purpose for the legal requirement (5μg/L) enforced in the Venice lagoon, without significant interfering species. In addition, analytical results of the HS-GC-NPD method have been compared with those obtained using the 4500 CN and EN ISO 14403 official methods for the determination of total and free cyanides, respectively. The new method has been successfully applied for the determination of cyanide concentrations in main influent and final effluent to the Venice lagoon to verify the efficiency of the industrial wastewater treatment plant of Porto Marghera (Venice, Italy). The capability of the proposed method to detect the WAD cyanides has been tested by studying the acid dissociation of K2[Ni(CN)4]. An unexpected speciation picture was obtained for this complex, which suggests that the present definition and analytical strategy of this cyanide class should be reconsidered. Copyright © 2013 Elsevier B.V. All rights reserved.

Phosphorescent nanoparticles for quantitative measurements of oxygen profiles in vitro and in vivo

PubMed Central

Choi, Nak Won; Verbridge, Scott S.; Williams, Rebecca M.; Chen, Jin; Kim, Ju-Young; Schmehl, Russel; Farnum, Cornelia E.; Zipfel, Warren R.; Fischbach, Claudia; Stroock, Abraham D.

2012-01-01

We present the development and characterization of nanoparticles loaded with a custom phosphor; we exploit these nanoparticles to perform quantitative measurements of the concentration of oxygen within three-dimensional (3-D) tissue cultures in vitro and blood vessels in vivo. We synthesized a customized ruthenium (Ru)-phosphor and incorporated it into polymeric nanoparticles via self-assembly. We demonstrate that the encapsulated phosphor is non-toxic with and without illumination. We evaluated two distinct modes of employing the phosphorescent nanoparticles for the measurement of concentrations of oxygen: 1) in vitro, in a 3-D microfluidic tumor model via ratiometric measurements of intensity with an oxygen-insensitive fluorophore as a reference, and 2) in vivo, in mouse vasculature using measurements of phosphorescence lifetime. With both methods, we demonstrated micrometer-scale resolution and absolute calibration to the dissolved oxygen concentration. Based on the ease and customizability of the synthesis of the nanoparticles and the flexibility of their application, these oxygen-sensing polymeric nanoparticles will find a natural home in a range of biological applications, benefiting studies of physiological as well as pathological processes in which oxygen availability and concentration play a critical role. PMID:22240511

Evaluation and use of U.S. Environmental Protection Agency Clean Watersheds Needs Survey data to quantify nutrient loads to surface water, 1978–2012

USGS Publications Warehouse

Ivahnenko, Tamara I.

2017-12-07

Changes in municipal and industrial point-source discharges over time have been an important factor affecting nutrient trends in many of the Nation’s streams and rivers. This report documents how three U.S. Environmental Protection Agency (EPA) national datasets—the Permit Compliance System, the Integrated Compliance Information System, and the Clean Watersheds Needs Survey—were evaluated for use in the U.S. Geological Survey National Water-Quality Assessment project to assess the causes of nutrient trends. This report also describes how a database of total nitrogen load and total phosphorous load was generated for select wastewater treatment facilities in the United States based on information reported in the EPA Clean Watersheds Needs Survey. Nutrient loads were calculated for the years 1978, 1980, 1982, 1984, 1986, 1988, 1990, 1992, 1996, 2000, 2004, 2008, and 2012 based on average nitrogen and phosphorous concentrations for reported treatment levels and on annual reported flow values.The EPA Permit Compliance System (PCS) and Integrated Compliance Information System (ICIS), which monitor point-source facility discharges, together are the Nation’s most spatially comprehensive dataset for nutrients released to surface waters. However, datasets for many individual facilities are incomplete, the PCS/ICIS historical data date back only to 1989, and historical data are available for only a limited number of facilities. Additionally, inconsistencies in facility reporting make it difficult to track or identify changes in nutrient discharges over time. Previous efforts made by the U.S. Geological Survey to “fill in” gaps in the PCS/ICIS data were based on statistical methods—missing data were filled in through the use of a statistical model based on the Standard Industrial Classification code, size, and flow class of the facility and on seasonal nutrient discharges of similar facilities. This approach was used to estimate point-source loads for a single point in time; it was not evaluated for use in generating a consistent data series over time.Another national EPA dataset that is available is the Clean Watersheds Needs Survey (CWNS), conducted every 4 years beginning 1973. The CWNS is an assessment of the capital needs of wastewater facilities to meet the water-quality goals set in the Clean Water Act. Data collected about these facilities include location and contact information for the facilities; population served; flow and treatment level of the facility; estimated capital needs to upgrade, repair, or improve facilities for water quality; and nonpoint-source best management practices.Total nitrogen and total phosphorous load calculations for each of the CWNS years were based on treatment level information and average annual outflow (in million gallons per day) from each of the facilities that had reported it. Treatment levels categories (such as Primary, Secondary, or Advanced) were substituted with average total nitrogen and total phosphorous concentrations for each treatment level based on those reported in literature. The CWNS dataset, like the PCS/ICIS dataset, has years where facilities did not report either a treatment level or an annual average outflow, or both. To fill in the data gaps, simple linear assumptions were made based on each facility’s responses to the survey in years bracketing the data gap or immediately before or after the data gap if open ended. Treatment level and flow data unique to each facility were used to complete the CWNS dataset for that facility.

Synchrotron-based analysis of chromium distributions in multicrystalline silicon for solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jensen, Mallory Ann; Hofstetter, Jasmin; Morishige, Ashley E.

Chromium (Cr) can degrade silicon wafer-based solar cell efficiencies at concentrations as low as 10(10) cm(-3). In this contribution, we employ synchrotron-based X-ray fluorescence microscopy to study chromium distributions in multicrystalline silicon in as-grown material and after phosphorous diffusion. We complement quantified precipitate size and spatial distribution with interstitial Cr concentration and minority carrier lifetime measurements to provide insight into chromium gettering kinetics and offer suggestions for minimizing the device impacts of chromium. We observe that Cr-rich precipitates in as-grown material are generally smaller than iron-rich precipitates and that Cri point defects account for only one-half of the total Crmore » in the as-grown material. This observation is consistent with previous hypotheses that Cr transport and CrSi2 growth are more strongly diffusion-limited during ingot cooling. We apply two phosphorous diffusion gettering profiles that both increase minority carrier lifetime by two orders of magnitude and reduce [Cr-i] by three orders of magnitude to approximate to 10(10) cm(-3). Some Cr-rich precipitates persist after both processes, and locally high [Cri] after the high-temperature process indicates that further optimization of the chromium gettering profile is possible. (C) 2015 AIP Publishing LLC.« less

[The spectrogram characteristics of organic blue-emissive light-emitting excitated YAG : Ce phosphor].

PubMed

Xi, Jian-Fei; Zhang, Fang-Hui; Mu, Qiang; Zhang, Mai-Li

2011-09-01

It is demonstrated that the panchromatic luminescence devices with organic blue-emissive light-emitting was fabricated. This technique used down conversion, which was already popular in inorganic power LEDs to obtain white light emission. A blue OLED device with a configuration of ITO/2T-NATA (30 nm)/AND : TBPe (50 Wt%, 40 nm)/Alq3 (100 nm)/LiF(1 nm)/Al(100 nm) was prepared via vacuum deposition process, and then coated with YAG : Ce phosphor layers of different thicknesses to obtain a controllable and uniform shape while the CIE coordinates were fine tuned. This development not only decreased steps of technics and degree of difficulty, but also applied the mature technology of phosphor. The results showed that steady spectrogram was obtained in the devices with phosphor, with a best performance of a maximum luminance of 13 840 cd x m(-2) which was about 2 times of that of the devices without phosphor; a maximum current efficiency of 17.3 cd x A(-1) was increased more two times more than the devices without phosphor. The emission spectrum could be adjusted by varying the concentration and thickness of the phosphor layers. Absoulte spectrogram of devices was in direct proportion with different driving current corresponding.

New life of recycled rare earth-oxides powders for lighting applications.

NASA Astrophysics Data System (ADS)

Carlo Ricci, Pier; Murgia, Massimiliano; Carbonaro, Carlo Maria; Sgariotto, Serena; Stagi, Luigi; Corpino, Riccardo; Chiriu, Daniele; Grilli, Maria Luisa

2018-03-01

In this work we analysed the optical and structural properties of Ce:YAG regenerated phosphors. The concentrate resulted as the final product of an industrial recycling process of waste electrical and electronic equipment (WEEE), and in particular fluorescent powders coming from spent lamps treatment plant. The waste pristine materials were re-utilized without any further purification and or separation process as starting materials to obtain a YAG matrix (Y2Al5O12) doped with Cerium ions. We tested out the recovered concentrate against commercial Ce:YAG phosphors comparing their structural and optical properties by means of XRD measurements and steady time and time resolved luminescence. The analysis reveals that the new phosphors obtained by scrap powder have the same crystal structure as the commercial reference sample and comparable optical properties. In particular, the Ce-related emission efficiency has a quantum yield of about 0.75 when excited at 450 nm, in good agreement with our reference sample and with the one of commercial powder presently exploited in white LED. This achievement strongly suggests the possibility of a new life for the exhausted phosphors and a possible step forward to a complete circular process for lighting equipment.

Determination of mercury distribution inside spent compact fluorescent lamps by atomic absorption spectrometry.

PubMed

Rey-Raap, Natalia; Gallardo, Antonio

2012-05-01

In this study, spent compact fluorescent lamps were characterized to determine the distribution of mercury. The procedure used in this research allowed mercury to be extracted in the vapor phase, from the phosphor powder, and the glass matrix. Mercury concentration in the three phases was determined by the method known as cold vapor atomic absorption spectrometry. Median values obtained in the study showed that a compact fluorescent lamp contained 24.52±0.4ppb of mercury in the vapor phase, 204.16±8.9ppb of mercury in the phosphor powder, and 18.74±0.5ppb of mercury in the glass matrix. There are differences in mercury concentration between the lamps since the year of manufacture or the hours of operation affect both mercury content and its distribution. The 85.76% of the mercury introduced into a compact fluorescent lamp becomes a component of the phosphor powder, while more than 13.66% is diffused through the glass matrix. By washing and eliminating all phosphor powder attached to the glass surface it is possible to classified the glass as a non-hazardous waste. Copyright © 2011 Elsevier Ltd. All rights reserved.

Synthesis and Optical Spectroscopy of YPO4:Eu3+ Orange-Red Phosphors

NASA Astrophysics Data System (ADS)

Yahiaoui, Z.; Hassairi, M. A.; Dammak, M.

2017-08-01

YPO4: x mol.% Eu3+ phosphors with different dopant concentrations ( x = 3, 5, 8, 11, 13) have been synthesized via high-temperature solid-state reaction. X-ray diffraction analysis and Raman and infrared (IR) spectroscopy were applied for detailed structural characterization. Under excitation at wavelength of 395 nm, the photoluminescence spectra displayed the 5D0 → 7F J ( J = 1, 2, 3, 4) intra-4 f shell transitions related to Eu3+ ion. The radiative lifetime was estimated using the Ω 2 and Ω 4 Judd-Ofelt intensity parameters. The highest luminescence intensity was achieved for an optimal europium concentration of 11 mol.%. The critical energy-transfer distance for Eu3+ ions was evaluated to be 10.74 Å. We also studied the temperature-dependent photoluminescence and Commission Internationale de l'Éclairage chromaticity diagram. It was found that Eu3+-doped YPO4 exhibited good thermal stability and its emission intensity decreased slightly above room temperature. In addition, the color purity of this phosphor was as high as 91% for the YPO4:13% Eu3+ sample, making it a potential orange-red phosphor for application in ultraviolet-pumped white light-emitting diodes.

Impulsive excitation of mechanoluminescence in gamma-irradiated CaSO4:Eu phosphors

NASA Astrophysics Data System (ADS)

Kher, R. S.; Dhoble, S. J.; Pandey, R. K.; Upadhyay, A. K.; Khokhar, M. S. K.

2011-01-01

The mechanoluminescence (ML) and thermoluminescence (TL) of γ-irradiated CaSO4:Eu phosphor have been studied. CaSO4 samples having different concentrations of Eu were prepared by dissolving CaSO4.2H2O in sulphuric acid and evaporating the excess acid around 300 °C. ML was excited impulsively by dropping a load onto the sample. Three distinct peaks have been observed in the ML intensity versus time curve. The ML intensity increases with the increasing concentration of the dopant. The effect of temperature on the shape and peak of ML intensity was also recorded. Growth, saturation and broadening in an ML peak were observed. TL glow curves of CaSO4:Eu phosphors at different concentrations contain two TL peaks: the first peak was observed at around 110 °C and the other at 210 °C. Experimental results suggest that the ML excitation is related to the movement of dislocation with defect centres, the increase in ML with temperature is due to the enhancement in dislocation capture probability, and the reduction is due to the thermal bleaching of defect centres.

Up-conversion white light of Tm 3+/Er 3+/Yb 3+ tri-doped CaF 2 phosphors

NASA Astrophysics Data System (ADS)

Cao, Chunyan; Qin, Weiping; Zhang, Jisen; Wang, Yan; Wang, Guofeng; Wei, Guodong; Zhu, Peifen; Wang, Lili; Jin, Longzhen

2008-03-01

Tm3+/Er3+/Yb3+ tri-doped CaF2 phosphors were synthesized using a hydrothermal method. The phosphors were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and up-conversion (UC) emission spectra. After annealing, the phosphors emitted white light under a 980 nm continuous wave diode laser (CW LD 2 W) excitation. As the excitation power density changed in the range of 20-260 W/cm2, the chromaticity coordinates of the UC light of the phosphor Ca0.885Tm0.005Er0.01Yb0.1F2 fell well in the white region of the 1931 CIE diagram. For the proportion of red, green and blue (RGB) in white light is strict, key factors for achieving UC white light, such as host materials, rare earth ions doping concentrations, annealing temperatures, as well as the excitation power densities, were investigated and discussed.

Effects of nitrogen and phosphorous stress on the formation of high value LC-PUFAs in Porphyridium cruentum.

PubMed

Hu, Hao; Wang, Hou-Feng; Ma, Lin-Lin; Shen, Xiao-Fei; Zeng, Raymond Jianxiong

2018-04-18

This study systematically examined the effect of nitrogen and phosphorous stress on the formation of linoleic acid (LA), arachidonic acid (ARA), and eicosapentaenoic acid (EPA) in Porphyridium cruentum gy-h56. P. cruentum was cultivated in six different media conferring different conditions of nitrogen (N) sufficiency/deprivation and phosphorous (P) sufficiency/limitation/deprivation. Over a 16-day cultivation process, the dry-weight content, proportion of total fatty acids (TFAs), and the concentration in the medium of linoleic acid (LA) were greatly improved by a maximum of 2.5-, 1.6-, and 1.1-fold, respectively, under conditions of N or P deprivation compared with N and P sufficiency. In contrast, levels of EPA or ARA were not enhanced under N or P stress conditions. Additionally, the results showed that N deprivation weakened the impact of P deficiency on the content and proportions of LA and EPA, while P deprivation enhanced the impact of N starvation on the content and proportions of LA and EPA. The conditions of N sufficiency and P deprivation (N+P-) were the optimal conditions for the production of LA, while the optimal conditions for EPA, ARA, and TFAs production were N sufficiency and P limitation (N+P-lim). This study suggests the potential application of combining N removal from saline wastewater with the production of LA, ARA, EPA, and biodiesel.

Color-tunable photoluminescence phosphors of Ce{sup 3+} and Tb{sup 3+} co-doped Sr{sub 2}La{sub 8}(SiO{sub 4}){sub 6}O{sub 2} for UV w-LEDs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Qingfeng; Liao, Libing, E-mail: clayl@cugb.edu.cn; Mei, Lefu

2015-05-15

A series of new luminescent emission-tunable phosphors Sr{sub 2}La{sub 8}(SiO{sub 4}){sub 6}O{sub 2}:Ce{sup 3+}, Tb{sup 3+} with apatite structure have been synthesized by a high temperature solid-state reaction. The phase structure, photoluminescence emission and excitation spectra, lifetime, as well as the effect of Tb{sup 3+} concentration are investigated to characterize the resulting samples. The critical distance was calculated to be 8.26 Å by using the concentration quenching method. The intense green emission was observed in the Sr{sub 2}La{sub 8}(SiO{sub 4}){sub 6}O{sub 2}:Ce{sup 3+}, Tb{sup 3+} phosphors on the basis of the efficient energy transfer from Ce{sup 3+} to Tb{sup 3+}more » with an efficiency of 68.55%. And a possible mechanism of the energy-transfer from Ce{sup 3+} to Tb{sup 3+} ion is also proposed. The results indicate that Sr{sub 2}La{sub 8}(SiO{sub 4}){sub 6}O{sub 2}:Ce{sup 3+}, Tb{sup 3+} phosphors have potential applications to be used as near UV-convertible phosphors for white light-emitting diodes because of the broad excitation in the near-ultraviolet range and the efficient green emission light. - Graphical abstract: Crystal structure and luminescence properties of Sr{sub 2}La{sub 8}(SiO{sub 4}){sub 6}O{sub 2}:Ce{sup 3+},Tb{sup 3+} phosphors have been discussed. - Highlights: • Ce{sup 3+} and Tb{sup 3+} ions entered both La sites in SLSO. • The energy transfer efficiency can reach at 68.55%. • The emitting color of SLSO phosphors shifted from the blue to green region.« less

Luminescence studies and infrared emission of erbium-doped calcium zirconate phosphor.

PubMed

Tiwari, Neha; Dubey, Vikas

2016-05-01

The near-infrared-to-visible upconversion luminescence behaviour of Er(3+)-doped CaZrO3 phosphor is discussed in this manuscript. The phosphor was prepared by a combustion synthesis technique that is suitable for less-time-taking techniques for nanophosphors. The starting materials used for sample preparation were Ca(NO3)2.4H2O, Zr(NO3)4 and Er(NO3)2, and urea was used as a fuel. The prepared sample was characterized by X-ray diffraction (XRD). The surface morphology of prepared phosphor was determined by field emission gun scanning electron microscopy (FEGSEM). The functional group analysis was determined by Fourier transform infrared (FTIR) spectroscopy. All prepared phosphors with variable Er(3+) concentrations (0.5-2.5 mol%) were studied by photoluminescence analysis. It was found that the excitation spectra of the prepared phosphor showed a sharp excitation peak centred at 980 nm. The emission spectra with variable Er(3+) concentrations showed strong peaks in the 555 nm and 567 nm range, with a dominant peak at 555 nm due to the ((2)H(11/2),(4)S(3/2)) transition and a weaker transition at 567 nm associated with 527 nm. Spectrophotometric determination of the peak was evaluated by the Commission Internationale de I'Eclairage (CIE) method These upconverted emissions were attributed to a two-photon process. The excitation wavelength dependence of the upconverted luminescence, together with its time evolution after infrared pulsed excitation, suggested that energy transfer upconversion processes were responsible for the upconversion luminescence. The upconversion mechanisms were studied in detail through laser power dependence. Excited state absorption and energy transfer processes were discussed as possible upconversion mechanisms. The cross-relaxation process in Er(3+) was also investigated. Copyright © 2015 John Wiley & Sons, Ltd.

Luminescence and Luminescence Quenching of K2Bi(PO4)(MoO4):Eu3+ Phosphors with Efficiencies Close to Unity.

PubMed

Grigorjevaite, Julija; Katelnikovas, Arturas

2016-11-23

A very good light emitting diode (LED) phosphor must have strong absorption, high quantum efficiency, high color purity, and high quenching temperature. Our synthesized K 2 Bi(PO 4 )(MoO 4 ):Eu 3+ phosphors possess all of the mentioned properties. The excitation of these phosphors with the near-UV or blue radiation results in a bright red luminescence dominated by the 5 D 0 → 7 F 2 transition at ∼615 nm. Color coordinates are very stable when changing Eu 3+ concentration or temperature in the range of 77-500 K. Furthermore, samples doped with 50% and 75% Eu 3+ showed quantum efficiencies close to 100% which is a huge benefit for practical application. Temperature dependent luminescence measurements showed that phosphor performance increases with increasing Eu 3+ concentration. K 2 Eu(PO 4 )(MoO 4 ) sample at 400 K lost only 20% of the initial intensity at 77 K and would lose half of the intensity only at 578 K. Besides, the ceramic disks with thicknesses of 0.33 and 0.89 mm were prepared from K 2 Eu(PO 4 )(MoO 4 ) powder, and it turned out that they efficiently converted the radiation of 375 nm LED to the red light. The conversion of 400 nm LED radiation to the red light was not complete; thus, the light sources with various tints of purple color were obtained. The combination of ceramic disks with 455 nm LED yielded the light sources with tints of blue color due to the low absorption of ceramic disk in this spectral range. In addition, these phosphors possess a very unique emission spectra; thus, they could also be applied in luminescent security pigments.

High-Temperature Surface Thermometry Technique based on Upconversion Nano-Phosphors

NASA Astrophysics Data System (ADS)

Combs, C.; Clemens, N.; Guo, X.; Song, H.; Zhao, H.; Li, K. K.; Zou, Y. K.; Jiang, H.

2011-11-01

Downconversion thermographic phosphors have been extensively used for high-temperature surface thermometry applications (e.g., aerothermodynamics, turbine blades) where temperature-sensitive paint is not viable. In downconversion techniques the phosphorescence is at longer wavelengths than the excitation source. We are developing a new upconversion thermographic phosphor technique that employs rare-earth-doped ceramics whose phosphorescence exhibit a strong temperature dependence. In the upconversion technique the phosphor is excited with near-IR light and emission is at visible wavelengths; thus, it does not require expensive UV windows and does not suffer from interference from background fluorescence. In this work the upconversion phosphors have been characterized in terms of their intensity, lifetimes and spectral content over a temperature range of 300K to 1500K. The technique has been evaluated for applications of 2D surface temperature measurements by using the total integrated intensity and the ratio of emission in different visible color bands. The results indicate that upconversion phosphor thermometry is a promising technique for making non-contact high-surface temperature measurements with good accuracy. Work supported by NASA under contract NNX11CG89P.

White long-lasting phosphorescence generation in a CaAl2Si2O8 : Eu2+, Mn2+, Dy3+ system through persistent energy transfer

NASA Astrophysics Data System (ADS)

Zhang, Jinsu; Chen, Baojiu; Sun, Jiashi; Li, Xiangping; Cheng, Lihong; Zhong, Haiyang

2012-08-01

Based on the persistent energy transfer principle, Mn2+ was introduced into a CaAl2Si2O8 : Eu2+/Dy3+ phosphor to achieve white long-lasting emissions. Eu2+, Mn2+ and Dy3+ tri-doped CaAl2Si2O8 phosphors with various Mn2+ concentrations were prepared via a solid-state reaction, and the crystal structure of the phosphors was identified by the x-ray diffraction technique. The luminescent properties of the Eu2+, Mn2+ and Dy3+ tri-doped CaAl2Si2O8 phosphors were studied. The energy transfer behaviour from Eu2+ to Mn2+ was analysed within the framework of Dexter theory. The physical mechanism of energy transfer was assigned to the electric dipole-quadrupole interaction. It was also demonstrated that the colour coordinates of the phosphors can be tuned from the blue region to the white region in the colour space. Furthermore, the afterglow decay and thermoluminescence curves were measured, indicating excellent phosphorescence properties of the current phosphors.

Luminescence in microcrystalline green emitting Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor

NASA Astrophysics Data System (ADS)

Panse, V. R.; Kokode, N. S.; Shinde, K. N.; Dhoble, S. J.

2018-03-01

Green emitting Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor powders were synthesized via the wet chemical synthesis and the luminescent proprieties were studied when excited at 380 nm and present a dominant and strong green luminescence peak at 543 nm, due to D-F transition. The preparation of Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor powders were confirmed by X-ray diffraction (XRD) results without any secondary or impurity phases. The size and morphology of the Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor powders were further examined by scanning electron microscopy (SEM). Photoluminescence (PL) results have shown strongest green emission at 543 nm, which is originated due to 5D4-7F5 transition of Tb3+ ion, for the Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor. The addition of concentration Tb3+ was greatly improved the photoluminescence properties of present phosphors. The present study suggests that the Li2Mg1-xZrO4:xTb3+ (0.1 ≤ x ≤ 2.0) phosphor is a strong candidate as a green component for phosphor-converted white light-emitting diodes (LEDs).

Effect of particle size and dopant concentration on photophysical properties of Eu3+-doped rare earth oxysulphide phosphor coatings.

PubMed

Chakradhar, R P S; Basu, Bharathibai J; Lakshmi, R V

2011-02-01

Europium-doped rare-earth oxysulphides (red phosphors) are often used as reference luminophore in pyrene-based pressure sensor coatings for aerodynamic applications. Different red phosphor samples were characterized for their particle size, chemical composition, photoluminescent properties and temperature sensitivity. The red phosphor samples were characterized using energy-dispersive X-ray spectroscopy (EDX) for elemental analysis and scanning electron microscopy (SEM) for morphology and particle size measurement. The particle size was in the range of 1.5-5.7 μm with morphology of hexagonal or spherical shape. It was found that phosphor with higher europium content exhibited higher luminescent emission intensity. The phosphor coatings were prepared by spraying a dispersion of the material in silicone resin. Smooth coatings were obtained by using phosphor samples with smaller particle size. Upon 334 nm excitation, the coatings showed characteristic luminescence 5D0→7FJ (J=0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 626 nm (5D0→7F2) of Eu3+ ions was stronger than the magnetic dipole transition located at 595 nm (5D0→7F1). Luminescence decay curves obeyed double exponential behaviour. The phosphor samples showed temperature sensitivity of -0.012 to -0.168%/°C in the temperature range of 25-50 °C. Copyright © 2010 Elsevier B.V. All rights reserved.

Enhancing the Photocatalytic Activity of Sr4 Al14 O25 : Eu2+ , Dy3+ Persistent Phosphors by Codoping with Bi3+ Ions.

PubMed

García, Carlos R; Oliva, Jorge; Romero, Maria Teresa; Diaz-Torres, Luis A

2016-03-01

The photocatalytic activity of Bismuth-codoped Sr 4 Al 14 O 25 : Eu 2+ , Dy 3+ persistent phosphors is studied by monitoring the degradation of the blue methylene dye UV light irradiation. Powder phosphors are obtained by a combustion synthesis method and a postannealing process in reductive atmosphere. The XRD patterns show a single orthorhombic phase Sr 4 Al 14 O 25 : Eu 2+ , Dy 3+ , Bi 3+ phosphors even at high Bismuth dopant concentrations of 12 mol%, suggesting that Bi ions are well incorporated into the host lattice. SEM micrographs show irregular micrograins with sizes in the range of 0.5-20 μm. The samples present an intense greenish-blue fluorescence and persistent emissions at 495 nm, attributed to the 5d-4f allowed transitions of Eu 2+ . The fluorescence decreases as Bi concentration increases; that suggest bismuth-induced traps formation that in turn quench the luminescence. The photocatalytic evaluation of the powders was studied under both 365 nm UV and solar irradiations. Sample with 12 mol% of Bi presented the best MB degradation activity; 310 min of solar irradiation allow 100% MB degradation, whereas only 62.49% MB degradation is achieved under UV irradiation. Our results suggest that codoping the persistent phosphors with Bi 3+ can be an alternative to enhance their photocatalytic activity. © 2016 The American Society of Photobiology.

Estimates of the occupational exposure to tenorm in the phosphoric acid production plant in Iran.

PubMed

Fathabadi, N; Vasheghani Farahani, M; Moradi, M; Hadadi, B

2012-09-01

Phosphate rock is used world wide for manufacturing phosphoric acid and several chemical fertilisers. It is known that the phosphate rock contains various concentrations of uranium, thorium, radium and their daughters. The subject of this study is the evaluation of the radiation exposure to workers in the phosphoric acid production plant due to technologically enhanced naturally occurring radioactive materials that can result from the presence of naturally occurring radioactive materials in phosphate ores used in the manufacturing of phosphoric acid. Radiation exposure due to direct gamma radiation, dust inhalation and radon gas has been investigated and external and internal doses of exposed workers have been calculated. Natural radioactivity due to (40)K, (226)Ra and (232)Th have been measured in phosphate rock, phosphogypsum, chemical fertilisers and other samples by gamma spectrometry system with a high-purity germanium. The average concentrations of (226)Ra and (40)K observed in the phosphate rock are 760 and 80 Bq kg(-1), respectively. Annual effective dose from external radiation had a mean value of ∼0.673 mSv y(-1). Dust sampling revealed greatest values in the storage area. The annual average effective dose from inhalation of long-lived airborne was 0.113 mSv y(-1). Radon gas concentrations in the processing plant and storage area were found to be of the same value as the background. In this study the estimated annual effective doses to workers were below 1 mSv y(-1).

Photoluminescence analysis of Ce{sup 3+}:Zn{sub 2}SiO{sub 4} & Li{sup +}+ Ce{sup 3+}:Zn{sub 2}SiO{sub 4}: phosphors by a sol-gel method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babu, B. Chandra, E-mail: chandrababuphd@gmail.com; Vandana, C. Sai; Guravamma, J.

2015-06-24

Here, we report on the development and photoluminescence analysis of Zn{sub 2}SiO{sub 4}, Ce{sup 3+}:Zn{sub 2}SiO{sub 4} & Li{sup +} + Ce{sup 3+}: Zn{sub 2}SiO{sub 4} novel powder phosphors prepared by a sol-gel technique. The total amount of Ce{sup 3+} ions was kept constant in this experiment at 0.05 mol% total doping. The excitation and emission spectra of undoped (Zn{sub 2}SiO{sub 4}) and Ce{sup 3+} doped Zn{sub 2}SiO{sub 4} and 0.05 mol% Li{sup +} co-doped samples have been investigated. Cerium doped Zn{sub 2}SiO{sub 4} powder phosphors had broad blue emission corresponding to the 2D{sub 3/2}→2F{sub J} transition at 443nm. Stable green-yellow-red emissionmore » has been observed from Zn{sub 2}SiO{sub 4} host matrix and also we have been observed the enhanced luminescence of Li{sup +} co-doped Zn{sub 2}SiO{sub 4}:Ce{sup 3+}. Excitation and emission spectra of these blue luminescent phosphors have been analyzed in evaluating their potential as luminescent screen coating phosphors.« less

Effect of the PVA (polyvinyl alcohol) concentration on the optical properties of Eu-doped YAG phosphors

NASA Astrophysics Data System (ADS)

Hora, Daniela A.; Andrade, Adriano B.; Ferreira, Nilson S.; Teixeira, Verônica C.; dos S. Rezende, Marcos V.

2016-10-01

The influence of the polyvinyl alcohol (PVA) concentration on the synthesis and structural, morphological and optical properties of Y3Al5O13: Eu (Eu-doped YAG) was systematically investigated in this work. The final concentration of PVA in the preparation step influenced the crystallite size and also the degree of particle agglomeration in Eu-doped YAG phosphors. X-ray excited optical luminescence (XEOL) emission spectra results indicated typical Eu3+ emission lines and an abnormally intense 5D0 → 7F4. The intensity parameters Ω2 and Ω4 were calculated and indicated the PVA concentration affects the ratio Ω2:Ω4. X-ray absorption spectroscopy (XAS) results showed Eu valence did not change and the symmetry around the Eu3+ is influenced by the PVA concentration. XEOL-XAS showed the luminescence increases as a function of energy.

Thermoluminescence properties of Li2B4O7:Cu, B phosphor synthesized using solution combustion technique

NASA Astrophysics Data System (ADS)

Ozdemir, A.; Altunal, V.; Kurt, K.; Depci, T.; Yu, Y.; Lawrence, Y.; Nur, N.; Guckan, V.; Yegingil, Z.

2017-12-01

To determine the effects of various concentrations of the activators copper (Cu) and boron (B) on the thermoluminescence (TL) properties of lithium tetraborate, the phosphor was first synthesized and doped with five different concentrations of copper (0.1-0.005 wt%) using solution combustion method. 0.01 wt% Cu was the concentration which showed the most significant increase in the sensitivity of the phosphor. The second sort of Li2B4O7:Cu material was prepared by adding B (0.001-0.03 wt%) to it. The newly developed copper-boron activated lithium tetraborate (Li2B4O7:Cu, B) material with 0.01 wt% Cu and 0.001 wt% B impurity concentrations was shown to have promise as a TL phosphor. The material formation was examined using powder x-Ray Diffraction (XRD) analysis and Scanning Electron Microscope (SEM) imaging. Fourier Transform Infrared (FT-IR) spectrum of the synthesized polycrystalline powder sample was also recorded. The TL glow curves were analyzed to determine various dosimetric characteristics of the synthesized luminophosphors. The dose response increased in a ;linear; way with the beta-ray exposure between 0.1-20 Gy, a dose range being interested in medical dosimetry. The response with changing photon and electron energy was studied. The rate of decay of the TL signal was investigated both for dark storage and under direct sunlight. Li2B4O7:Cu, B showed no individual variation of response in 9 recycling measurements. The fluorescence spectrum was determined. The kinetic parameters were estimated by different methods and the results discussed. The studied properties of synthesized Li2B4O7:Cu, B were found all favorable for dosimetric purposes.

Crystal structure, thermally stability and photoluminescence properties of novel Sr{sub 10}(PO{sub 4}){sub 6}O:Eu{sup 2+} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Qingfeng; Liao, Libing, E-mail: clayl@cugb.edu.cn; Mei, Lefu

2015-03-15

A series of novel luminescent phosphors Sr{sub 10}(PO{sub 4}){sub 6}O:Eu{sup 2+} with apatite structure were synthesized via a high temperature solid-state reaction. The phase structure, photoluminescence (PL) properties, the PL thermal stability, as well as the fluorescence decay curves of the samples were investigated to characterize the resulting samples, and the selected Sr{sub 9.97}(PO{sub 4}){sub 6}O:0.03Eu{sup 2+} phosphor exhibits strong thermal quenching resistance, retaining the luminance of 88.73% at 150 °C. The quenching concentration of Eu{sup 2+} in Sr{sub 10}(PO{sub 4}){sub 6}O was about 0.03 attributing to the dipole–quadrupole interaction. The Sr{sub 10}(PO{sub 4}){sub 6}O:Eu{sup 2+} phosphor exhibited a broad-bandmore » blue emission at 439 nm upon excitation at 346 nm. The results indicate that Sr{sub 10}(PO{sub 4}){sub 6}O:Eu{sup 2+} phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Graphical abstract: Sr{sub 10}(PO{sub 4}){sub 6}O:Eu{sup 2+} phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Highlights: • Sr{sub 9.97}(PO{sub 4}){sub 6}O:0.03Eu{sup 2+} phosphor exhibits strong thermal quenching resistance. • Two different Eu{sup 2+} emission centers exists in Sr{sub 10}(PO{sub 4}){sub 6}O. • The activation energy was also estimated for the Eu{sup 2+} luminescence center.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Peican; Zhou, Liya, E-mail: zhouliyatf@163.com; Mo, Fuwang

Graphical abstract: - Highlights: • Novel Eu{sup 2+} doped Sr{sub 6}Ca{sub 4}(PO{sub 4}){sub 6}F{sub 2} phosphors was synthesized for the first time. • The Sr{sub 6}Ca{sub 4}(PO{sub 4}){sub 6}F{sub 2}:Eu{sup 2+} phosphors produced blue light when irradiated at 368 nm. • The emission band of the sample could be decomposed into two Gaussian profiles. - Abstract: For the first time, a series of novel blue light-emitting phosphors Sr{sub 6}Ca{sub 4}(PO{sub 4}){sub 6}F{sub 2}:Eu{sup 2+} were synthesized by a traditional solid-state reaction. The phosphors exhibited a broad and intense excitation band that could be pumped by near ultraviolet to exhibit amore » broad photoluminescence band ranging from 400 nm to 530 nm peaking at 452 nm. Quenching concentration was 0.05 mol. Furthermore, the mechanism of concentration quenching involving SCPF:Eu{sup 2+} was demonstrated to be a dipole–dipole interaction with critical distance of 27.95 Å. Decay time curves were also measured to validate energy transfer, and quantum efficiency is investigated. The chromaticity diagram of Commission Internationale de l’Eclairage indicated that SCPF:Eu{sup 2+} may be used as a blue-emitting component for white light-emitting diode applications.« less

Synthesis and luminescence studies of Eu (III) doped Sr2P2O7 phosphor for white LED applications

NASA Astrophysics Data System (ADS)

Khan, Z. S.; Ingale, N. B.; Omanwar, S. K.

2018-05-01

Europium (III) doped distrontium diphosphate (Sr2P2O7) is synthesized by slow vaporization method and its luminescence properties are carried out. Using X-Ray diffraction, the crystal structure of this material was confirmed. Photoluminescence (PL) measurement make clear the phosphor exhibited intense emission at 593 nm (yellow) and 612 nm (orange) respectively corresponding to 5D0→7F1 and 5D0→7F2 transitions of Eu3+ on excitation with most favourable 394 nm wavelengths. The remaining excitation peaks at 381 nm and 465 nm with broad band 200-310 nm are also witness in the excitation spectra. The particle morphology using SEM images shows micro level particles for this phosphor. The effect of concentration of Eu3+ ions on the PL intensity has also been investigated. It has been observed that the powder sample exhibits highest PL emission intensity for Eu3+ concentration of about 0.02 moles. The emission spectra exhibit orange performance (CIE chromaticity coordinates: X = 0.672, Y = 0.328), which is due to the 5D0→7F2 transitions of Eu3+ ions. This phosphor is very good for white LED applications.

Cathode catalysts for primary phosphoric acid fuel cells

NASA Technical Reports Server (NTRS)

1981-01-01

Alkylation or carbon Vulcan XC-72, the support carbon, was shown to provide the most stable bond type for linking cobalt dehydrodibenzo tetraazannulene (CoTAA) to the surface of the carbon; this result is based on data obtained by cyclic voltammetry, pulse voltammetry and by release of 14C from bonded CoTAA. Half-cell tests at 100 C in 85% phosphoric acid showed that CoTAA bonded to the surface of carbon (Vulcan XC-72) via an alkylation procedure is a more active catalyst than is platinum based on a factor of two improvement in Tafel slope; dimeric CoTAA had catalytic activity equal to platinum. Half-cell tests also showed that bonded CoTAA catalysts do not suffer a loss in potential when air is used as a fuel rather than oxygen. Commercially available polytetrafluroethylene (PTFE) was shown to be unstable in the fuel cell environment with degradation occurring in 2000 hours or less. The PTFE was stressed at 200 C in concentrated phosphoric acid as well as electrochemically stressed in 150 C concentrated phosphoric acid; the surface chemistry of PTFE was observed to change significantly. Radiolabeled PTFE was prepared and used to verify that such chemical changes also occur in the primary fuel cell environment.

Tuning transport selectivity of ionic species by phosphoric acid gradient in positively charged nanochannel membranes.

PubMed

Yang, Meng; Yang, Xiaohai; Wang, Kemin; Wang, Qing; Fan, Xin; Liu, Wei; Liu, Xizhen; Liu, Jianbo; Huang, Jin

2015-02-03

The transport of ionic species through a nanochannel plays important roles in fundamental research and practical applications of the nanofluidic device. Here, we demonstrated that ionic transport selectivity of a positively charged nanochannel membrane can be tuned under a phosphoric acid gradient. When phosphoric acid solution and analyte solution were connected by the positively charged nanochannel membrane, the faster-moving analyte through the positively charged nanochannel membrane was the positively charged dye (methylviologen, MV(2+)) instead of the negatively charged dye (1,5-naphthalene disulfonate, NDS(2-)). In other words, a reversed ion selectivity of the nanochannel membranes can be found. It can be explained as a result of the combination of diffusion, induced electroosmosis, and induced electrophoresis. In addition, the influencing factors of transport selectivity, including concentration of phosphoric acid, penetration time, and volume of feed solution, were also investigated. The results showed that the transport selectivity can further be tuned by adjusting these factors. As a method of tuning ionic transport selectivity by establishing phosphoric acid gradient, it will be conducive to improving the separation of ionic species.

Photoluminescence properties and energy transfer of color tunable MgZn₂(PO₄)₂:Ce³⁺,Tb³⁺ phosphors.

PubMed

Xu, Mengjiao; Wang, Luxiang; Jia, Dianzeng; Zhao, Hongyang

2015-11-21

A series of Ce(3+)/Tb(3+) co-doped MgZn2(PO4)2 phosphors have been synthesized by the co-precipitation method. Their structure, morphology, photoluminescence properties, decay lifetime, thermal stability and luminous efficiency were investigated. The possible energy transfer mechanism was proposed based on the experimental results and detailed luminescence spectra and decay curves of the phosphors. The critical distance between Ce(3+) and Tb(3+) ions was calculated by both the concentration quenching method and the spectral overlap method. The energy transfer mechanism from the Ce(3+) to Tb(3+) ion was determined to be dipole-quadrupole interaction, and the energy transfer efficiency was 85%. By utilizing the principle of energy transfer and appropriate tuning of Ce(3+)/Tb(3+) contents, the emission color of the obtained phosphors can be tuned from blue to green light. The MgZn2(PO4)2:Ce(3+),Tb(3+) phosphor is proved to be a promising UV-convertible material capable of green light emitting in UV-LEDs due to its excellent thermal stability and luminescence properties.

Eu2+-doped Ba2GaB4O9Cl blue-emitting phosphor with high color purity for near-UV-pumped white light-emitting diodes

NASA Astrophysics Data System (ADS)

Gao, Zhiwen; Deng, Huajuan; Xue, Na; Jeong, Jung Hyun; Yu, Ruijin

2018-01-01

Eu2+-doped borate fluoride Ba2GaB4O9Cl was synthesized by the conventional high-temperature solid-state reaction. The crystal structure and luminescence properties of the phosphors, as well as their thermal luminescence quenching capabilities and CIE chromaticity coordinates were systematically investigated. Under the excitation at 340 nm, the phosphor exhibited an asymmetric broad-band blue emission with a peak at 445 nm, which is ascribed to the 4f-5d transition of Eu2+. It was further proved that energy transfer among the nearest neighbor ions is the major mechanism for concentration quenching of Eu2+ in Ba2-xGaB4O9Cl:xEu2+ phosphors. The luminescence quenching temperature is 432 K. The CIE color coordinates are very close to those of BaMgAl10O17:Eu2+ (BAM). All the properties indicated that the blue-emitting Ba2GaB4O9Cl:Eu2+ phosphor has potential application in white LEDs.

Luminescent properties of MAl(SO4)2 Br:Eu(3+) (M = Sr or Mg) red phosphors for near-UV light-emitting diodes.

PubMed

Deshmukh, Priti B; Puppalwar, S P; Dhoble, N S; Dhoble, S J

2015-02-01

Eu(3+) -activated MAl(SO4 )2 Br phosphors (where M = Mg or Sr) are successfully prepared using a wet chemical reaction technique. The samples are characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopies. The XRD pattern revealed that both the samples are microcrystalline in nature. PL of Eu(3+) -doped SrAl(SO4 )2 Br and MgAl(SO4 )2 Br phosphors exhibited characteristic red emission coming from the (5) D0  → (7) F2 (616 nm) electron transition, when excited by 396 nm wavelength of light. The maximum intensity of luminescence was observed at a concentration of 1 mol% Eu(3+) . The intensity of the electric dipole transition at 616 nm is greater than that of the magnetic dipole transition at 594 nm. The results showed that MAl(SO4 )2 Br:Eu(3+) , (M = Mg, Sr) phosphors have potential application in near-UV light-emitting diodes as efficient red-emitting phosphor. Copyright © 2014 John Wiley & Sons, Ltd.

Method of extracting iodine from liquid mixtures of iodine, water and hydrogen iodide

DOEpatents

Mysels, Karol J.

1979-01-01

The components of a liquid mixture consisting essentially of HI, water and at least about 50 w/o iodine are separated in a countercurrent extraction zone by treating with phosphoric acid containing at least about 90 w/o H.sub.3 PO.sub.4. The bottom stream from the extraction zone is substantially completely molten iodine, and the overhead stream contains water, HI, H.sub.3 PO.sub.4 and a small fraction of the amount of original iodine. When the water and HI are present in near-azeotropic proportions, there is particular advantage in feeding the overhead stream to an extractive distillation zone wherein it is treated with additional concentrated phosphoric acid to create an anhydrous HI vapor stream and bottoms which contain at least about 85 w/o H.sub.3 PO.sub.4. Concentration of these bottoms provides phosphoric acid infeed for both the countercurrent extraction zone and for the extractive distillation zone.

Enhanced Emission from Li2CaSiO4:Dy3+ Phosphors by Doping with Al3+ and B3+

NASA Astrophysics Data System (ADS)

Erdoğmuş, E.

2016-05-01

Pure Li2CaSiO4, Li2CaSiO4:Dy3+ and Al3+, B3+ co-doped materials were prepared by a solid-state reaction in air at 900°C for 6 h and characterized by using powder XRD. The luminescence properties of the synthesized phosphors were measured at room temperature with a spectrofluorometer. Li2CaSiO4:Dy3+ emits at 484, 575, and 660 nm upon 352 nm excitation. The emission spectrum intensity of Dy3+ increased from 0.01 to 0.06 mol.%, and beyond 0.06 mol.%, concentration quenching was observed. Also, in this study, the effects of boric acid and aluminum oxide concentration on the photoluminescence properties of Dy3+ doped phosphors were investigated. The results showed that boric acid and aluminum oxide were effective in improving the photoluminescence intensity of Li2CaSiO4:Dy3+ compounds.

Catalyst evaluation for oxygen reduction reaction in concentrated phosphoric acid at elevated temperatures

NASA Astrophysics Data System (ADS)

Hu, Yang; Jiang, Yiliang; Jensen, Jens Oluf; Cleemann, Lars N.; Li, Qingfeng

2018-01-01

Phosphoric acid is the common electrolyte for high-temperature polymer electrolyte fuel cells (HT-PEMFCs) that have advantages such as enhanced CO tolerance and simplified heat and water management. The currently used rotating disk electrode technique is limited to tests in dilute solutions at low temperatures and hence is not suitable for catalyst evaluation for HT-PEMFCs. In this study, we have designed and constructed a half-cell setup to measure the intrinsic activities of catalysts towards the oxygen reduction reaction (ORR) in conditions close to HT-PEMFC cathodes. By optimization of the hydrophobic characteristics of electrodes and the catalyst layer thickness, ORR activities of typical Pt/C catalysts are successfully measured in concentrated phosphoric acid at temperatures above 100 °C. In terms of mass-specific activities, the catalyst exhibits about two times higher activity in the half-cell electrode than that observed in fuel cells, indicating the feasibility of the technique as well as the potential for further improvement of fuel cell electrode performance.

[Distribution of soil organic carbon, total nitrogen, total phosphorus and water stable aggregates of cropland with different soil textures on the Loess Plateau, Northwest China].

PubMed

Ge, Nan Nan; Shi, Yun; Yang, Xian Long; Zhang, Qing Yin; Li, Xue Zhang; Jia, Xiao Xu; Shao, Ming An; Wei, Xiao Rong

2017-05-18

In this study, combined with field investigation and laboratory analyses, we assessed the distribution of soil organic carbon, nitrogen, phosphorous contents and their stoichiometric ratios, and the distribution of soil water stable aggregates along a soil texture gradient in the cropland of the Loess Plateau to understand the effect of soil texture and the regulation of soil aggregates on soil fertility in cropland. The results showed that, with the change from fine soils to coarse soils along the texture gradient (loam clay→ clay loam→ sandy loam), the contents of macroaggregates, organic carbon, nitrogen, phosphorous and their stoichiometric ratios decreased, while pH value and microaggregates content showed an opposite changing pattern. The contents of macroaggregates, organic carbon, nitrogen, phosphorous, and C/P and N/P were significantly increased, but pH value and microaggregates content were significantly decreased with increasing the soil clay content. Furthermore, the contents of organic carbon, nitrogen, phosphorous, and C/P and N/P increased with the increase of macroaggregates content. These results indicated that soil fertility in croplands at a regional scale was mainly determined by soil texture, and was regulated by soil macroaggregates.

Investigation of Pu(IV)-acetohydroxamic acid complex by solvent extraction with di(2-ethylhexyl) phosphoric acid

NASA Astrophysics Data System (ADS)

Brown, M. Alex; Paulenova, Alena; Tkac, Peter

2010-03-01

The stability constant of the Pu(IV)-acetohydroxamic acid complex Pu(AHA)3+ at 1 M ionic strength (pH = 0) has been investigated by method of solvent extraction. Di(2-ethylhexyl) phosphoric acid (HDEHP) was used to extract Pu(IV) from perchloric and nitric acid media at various AHA concentrations. Distribution ratios over a range of ligand concentrations were used in conjunction with graphical methods to obtain logβ1 = 14.3 ± 0.03 in perchloric acid. The stability constant determined from solutions in nitric acid was excluded because of the uncertainty in plutonium speciation.

The effect of Eu{sup 2+} doping concentration on luminescence properties of Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+} yellow phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Yue; Liu, Quansheng, E-mail: liuqs@cust.edu.cn; School of Physics, JiLin University, No. 2699 Qianjin Street, Changchun 130012

2013-10-15

Graphical abstract: - Highlights: • The concentration quenching mechanism of Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+}can be interpreted by the dipole–dipole (d–d) interaction of Eu{sup 2+} ions. • The average electronegativity of O{sup 2−} ions located around Eu{sup 2+} ion is 1.9991 eV. • The optimum concentration of Eu{sup 2+} ions in Sr{sub 3}B{sub 2}O{sub 6} is 7 mol%. • Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+} is a hexagonal crystal structure. - Abstract: The Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+} yellow phosphors were synthesized by high-temperature solid state reaction method. The crystal structure and optical properties of the Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+}more » phosphor was studied. Results indicate that Sr{sub 3}B{sub 2}O{sub 6}:Eu{sup 2+} has a hexagonal crystal structure. The excitation spectrum indicates that this phosphor can be effectively excited by ultraviolet light of near 390 nm and blue light of 460 nm. The emission spectrum shows a intense broad band spectrum peaking at 566 nm, which corresponds to the 4f{sup 6}({sup 7}F)5d ({sup 2}e{sub g})→{sup 8}S{sub 7/2} (4f{sup 7})transition of Eu{sup 2+} ion. The excitation spectrum is a broad asymmetric excitation band extending from 300 nm to 500 nm and the main excitation peak is at 468 nm. The average electronegativity of O{sup 2−} ions located around Eu{sup 2+} ion is 1.9991 eV. The optimum concentration of Eu{sup 2+} is 7 mol%. The concentration quenching mechanism can be interpreted by the dipole–dipole (d–d) interaction of Eu{sup 2+} ions.« less

Color-tunable and white luminescence properties via energy transfer in single-phase KNaCa2(PO4)2:A (A = Ce3+, Eu2+, Tb3+, Mn2+, Sm3+) phosphors.

PubMed

Geng, Dongling; Shang, Mengmeng; Zhang, Yang; Lian, Hongzhou; Lin, Jun

2013-12-02

A series of single-phase phosphors based on KNaCa2(PO4)2 (KNCP):A (A = Ce(3+), Eu(2+), Tb(3+), Mn(2+), Sm(3+)) have been prepared via the Pechini-type sol-gel method. Photoluminescence (PL) and cathodoluminescence (CL) properties of Ce(3+)-, Eu(2+)-, Tb(3+)-, Mn(2+)-, and Sm(3+)-activated KNCP phosphors were investigated. For the A singly doped KNCP samples, they exhibit the characteristic emissions of the A activator. Na(+) ions exhibit the best charge compensation result among Li(+), Na(+), and K(+) ions for Ce(3+)-, Tb(3+)-, and Sm(3+)-doped KNCP samples. The energy transfers from Ce(3+) to Tb(3+) and Mn(2+) ions as well as Eu(2+) to Tb(3+) and Mn(2+) have been validated. The emission colors of KNCP:Ce(3+)/Eu(2+), Tb(3+)/Mn(2+), Na(+) samples can be adjusted by energy transfer process and changing the Tb(3+)/Mn(2+) concentration. More importantly, white light emission in KNCP:Eu(2+), Mn(2+) system has been obtained. The KNCP:Tb(3+), Na(+) sample shows tunable luminescence from blue to cyan and then to green with the change of Tb(3+) concentration due to the cross-relaxation from (5)D3 to (5)D4. A white emission can also be realized in the single-phase KNCP host by reasonably adjusting the doping concentrations of Tb(3+) and Sm(3+) (reddish-orange emission) under low-voltage electron beam excitation. Additionally, the temperature-dependent PL properties of as-prepared phosphors reveal that the KNCP host has good thermal stability. Therefore, the KNCP:A (A = Ce(3+), Eu(2+), Tb(3+), Mn(2+), Sm(3+)) phosphors could be regarded as good candidates for UV W-LEDs and FEDs.

Synthesis and luminescence properties of CaSnO3 :Bi3+ blue phosphor and the emission improvement by Li+ ion.

PubMed

Cao, Renping; Zhang, Jinlong; Wang, Wudi; Hu, Qianglin; Li, Wensheng; Ruan, Wen; Ao, Hui

2017-09-01

CaSnO 3 :Bi 3+ blue-emitting phosphor was synthesized using a high-temperature solid-state reaction method in air. The crystal structures and luminescence properties were investigated. A broad emission band peaking at ~448 nm upon excitation at 262 and 308 nm was observed in the range 330-680 nm at room temperature due to 3 P 1  →  1 S 0 transition of the Bi 3+ ion. The chromaticity coordinate was (0.1786, 0.1665). The optimal Bi 3+ ion concentration was ~0.6 mol% in CaSnO 3 :Bi 3+ phosphor. The emission spectrum of CaSnO 3 :Bi 3+ phosphor showed a blue-shift with increasing temperature from 50 to 300 K due to the influence of temperature on the electron transition of the Bi 3+ ion. The emission intensity of CaSnO 3 :Bi 3+ phosphor may be increased ~1.45 times by co-doping Li + ions as a charge compensator and fluxing agent. The luminescence mechanism is explained by a configurational coordinate diagram of Bi 3+ ion in CaSnO 3 :Bi 3+ phosphor. Copyright © 2017 John Wiley & Sons, Ltd.

Host sensitized near-infrared emission in Nd3+ doped different alkaline-sodium-phosphate phosphors

NASA Astrophysics Data System (ADS)

Balakrishna, A.; Swart, H. C.; Kroon, R. E.; Ntwaeaborwa, O. M.

2018-04-01

Near-infrared (NIR) emitting phosphors of different alkaline based sodium-phosphate (MNa[PO4], where M = Mg, Ca, Sr and Ba were prepared by a conventional solution combustion method with fixed doping concentration of Nd3+ (1.0 mol%). The phosphors were characterized by powder X-ray diffraction, field emission scanning electron microscope, Fourier transform infrared spectroscopy, UV-vis spectroscopy and fluorescent spectrophotometry. The optical properties including reflectance, excitation and emission were investigated. The excitation spectra of the phosphors were characterized by a broadband extending from 450 to 900 nm. Upon excitation with a wavelength of 580 nm, the phosphor emits intensely infrared region at 872 nm, 1060 nm and 1325 nm which correspond to the 4F3/2 → 4I9/2, 4F3/2 → 4I11/2 and 4F3/2 → 4I13/2 transitions of Nd3+ ions and were found to vary for the different hosts. The strongest emission wavelength reaches 1060 nm. The most intense emission of Nd3+ was observed from Ca2+ incorporated host. The down conversion emissions of the material fall in the NIR region suggesting that the prepared phosphors have potential application in the development of photonic devices emitting in the NIR.

Preparation and luminescence properties of orange-red Ba3Y(PO4)3:Sm3+ phosphors

NASA Astrophysics Data System (ADS)

Xu, Qiguang; Xu, Denghui; Sun, Jiayue

2015-04-01

Ba3Y(PO4)3:Sm3+ phosphors were prepared by a high temperature solid-state reaction in air. X-ray diffraction (XRD), photoluminescence spectra and temperature-dependent emission spectra were utilized to characterize the structure and luminescence properties of the as-prepared phosphor. The results show that the phosphor can be efficiently excited by ultraviolet light and emit a satisfactory orange-red performance, nicely, fitting in well with the widely used UV LED chip. Under 403 nm excitation, the 4G5/2 → 6HJ (J = 5/2, 7/2, 9/2, and 11/2) emissions of Sm3+ are obviously observed. The optimum doping concentration is 5 mol% and corresponding quenching behavior is ascribed to be electric dipole-dipole interaction according to Dexter's theory. The temperature dependent luminescence of Ba3Y(PO4)3:Sm3+ phosphor is also discussed, and the activation energy for thermal quenching is calculated as 0.34 eV. Furthermore, the chromaticity coordinates of Ba3Y(PO4)3:Sm3+ phosphor are calculated to be (0.5558, 0.4380) and the lifetime values of Ba3Y0.995(PO4)3:0.005Sm3+ was 2.45 ms.

Instability of phosphorous doped SiO2 in 4H-SiC MOS capacitors at high temperatures

NASA Astrophysics Data System (ADS)

Idris, M. I.; Weng, M. H.; Chan, H.-K.; Murphy, A. E.; Clark, D. T.; Young, R. A. R.; Ramsay, E. P.; Wright, N. G.; Horsfall, A. B.

2016-12-01

In this paper, the effect of inclusion of phosphorous (at a concentration below 1%) on the high temperature characteristics (up to 300 °C) of the SiO2/SiC interface is investigated. Capacitance-voltage measurements taken for a range of frequencies have been utilized to extract parameters including flatband voltage, threshold voltage, effective oxide charge, and interface state density. The variation of these parameters with temperature has been investigated for bias sweeps in opposing directions and a comparison made between phosphorous doped and as-grown oxides. At room temperature, the effective oxide charge for SiO2 may be reduced by the phosphorous termination of dangling bonds at the interface. However, at high temperatures, the effective charge in the phosphorous doped oxide remains unstable and effects such as flatband voltage shift and threshold voltage shift dominate the characteristics. The instability in these characteristics was found to result from the trapped charges in the oxide (±1012 cm-3) or near interface traps at the interface of the gate oxide and the semiconductor (1012-1013 cm-2 eV-1). Hence, the performance enhancements observed for phosphorous doped oxides are not realised in devices operated at elevated temperatures.

Responses of microalgae Coelastrella sp. to stress of cupric ions in treatment of anaerobically digested swine wastewater.

PubMed

Li, Xiang; Yang, William L; He, Huijun; Wu, Shaohua; Zhou, Qi; Yang, Chunping; Zeng, Guangming; Luo, Le; Lou, Wei

2018-03-01

Microalgae Coelastrella sp. could remove nutrients from anaerobically digested swine wastewater (ADSW) effectively, while its responses to the stress of Cu(II) were not well understood. In this paper, nutrients removal and growth of Coelastrella sp. were investigated at the presence of Cu(II) in ADSW. Results showed ammonium nitrogen concentration in ADSW decreased with culturing duration, while increased with an increased Cu(II) concentration. Total phosphorous concentration decreased with time, while did not drop in 4 days at Cu(II) concentration ≥1.0 mg/L. Microalgal growth was inhibited at all the Cu(II) concentrations, and ceased in about 6-8 days at Cu(II) concentration ≥1.0 mg/L. With an increased Cu(II) concentration, the contents of chlorophyll a and proteins decreased, those of malondialdehyde and superoxide dismutase, and ratios of octadecanoic acid (C18:0), hexadecanoic acid (C16:0) and octadecenoic acid (C18:1) to fatty acids in Coelastrella sp. increased, while octadecatrienoic acid (C18:3) gradually disappeared. Copyright © 2017 Elsevier Ltd. All rights reserved.

Physical Mechanisms Routing Nutrients in the Central Red Sea

NASA Astrophysics Data System (ADS)

Zarokanellos, Nikolaos D.; Kürten, Benjamin; Churchill, James H.; Roder, Cornelia; Voolstra, Christian R.; Abualnaja, Yasser; Jones, Burton H.

2017-11-01

Mesoscale eddies and boundary currents play a key role in the upper layer circulation of the Red Sea. This study assesses the physical and biochemical characteristics of an eastern boundary current (EBC) and recurrent eddies in the central Red Sea (CRS) using a combination of in situ and satellite observations. Hydrographic surveys in November 2013 (autumn) and in April 2014 (spring) in the CRS (22.15°N-24.1°N) included a total of 39 and 27 CTD stations, respectively. In addition, high-resolution hydrographic data were acquired in spring 2014 with a towed undulating vehicle (ScanFish). In situ measurements of salinity, temperature, chlorophyll fluorescence, colored dissolved organic matter (CDOM), and dissolved nitrate: phosphorous ratios reveal distinct water mass characteristics for the two periods. An EBC, observed in the upper 150 m of the water column during autumn, transported low-salinity and warm water from the south toward the CRS. Patches of the low-salinity water of southern origin tended to contain relatively high concentrations of chlorophyll and CDOM. The prominent dynamic feature observed in spring was a cyclonic/anticyclonic eddy pair. The cyclonic eddy was responsible for an upward nutrient flux into the euphotic zone. Higher chlorophyll and CDOM concentrations, and concomitant lower nitrate:phosphorous ratios indicate the influence of the EBC in the CRS at the end of the stratified summer period.

Study of formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors.

PubMed

Dubey, Vikas; Kaur, Jagjeet; Parganiha, Yogita; Suryanarayana, N S; Murthy, K V R

2016-04-01

This paper reports the thermoluminescence properties of Eu(3+) doped different host matrix phosphors (SrY2O4 and Y4Al2O9). The phosphor is prepared by high temperature solid state reaction method. The method is suitable for large scale production and fixed concentration of boric acid using as a flux. The prepared samples were characterized by X-ray diffraction technique and the crystallite size calculated by Scherer's formula. The prepared phosphor characterized by Scanning Electron Microscopic (SEM), Fourier Transform Infrared (FTIR), Energy Dispersive X-ray analysis (EDX), thermoluminescence (TL) and Transmission Electron Microscopic (TEM) techniques. The prepared phosphors for different concentration of Eu(3+) ions were examined by TL glow curve for UV, beta and gamma irradiation. The UV 254nm source used for UV irradiation, Sr(90) source was used for beta irradiation and Co(60) source used for gamma irradiation. SrY2O4:Eu(3+)and Y4Al2O9:Eu(3+) phosphors which shows both higher temperature peaks and lower temperature peaks for UV, beta and gamma irradiation. Here UV irradiated sample shows the formation of shallow trap (surface trapping) and the gamma irradiated sample shows the formation of deep trapping. The estimation of trap formation was evaluated by knowledge of trapping parameters. The trapping parameters such as activation energy, order of kinetics and frequency factor were calculated by peak shape method. Here most of the peak shows second order of kinetics. The effect of gamma, beta and UV exposure on TL studies was also examined and it shows linear response with dose which indicate that the samples may be useful for TL dosimetry. Formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors is discussed in this paper. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of europium ion concentration on the structural and photoluminescence properties of novel Li2BaZrO4: Eu3+ nanocrystals

NASA Astrophysics Data System (ADS)

Ahemen, I.; Dejene, F. B.; Kroon, R. E.; Swart, H. C.

2017-12-01

This work reports the influence of Eu3+ ion concentration on the structure and photoluminescence properties of Li2BaZrO4 nanocrystals including its intrinsic quantum efficiency (IQE). Chemical bath method was employed in the synthesis procedure. X-ray diffraction results showed tetragonal phase for Eu3+ ion concentration in the range 1 and 7 mol% and cubic phase at 8 mol%. The presence of barium oxide (BaO) was confirmed from selected area electron diffraction (SAED). The excitation spectra for these phosphors consisted of broad charge transfer (CT) bands due to the combination of Zr4+ - O2- and Eu3+-O2- charge transfer states. Superimposed on the CT band were direct excitation levels of Eu3+ and Ba2+ ions, in the range 320-450 nm. At high Eu3+ ions concentrations, the intensities of CT bands decreased because some of the ions were coordinated with Ba2+ ions. Photoluminescence emissions for all the doped samples at room temperature appeared to be entirely from intraconfigurational Eu3+ emissions and depended both on the site symmetry as well as the ion concentration. The quadrupole-quadrupole multipolar process was found to be solely responsible for the luminescence quenching. The intensity parameters (Ω2 ,Ω4), asymmetry ratio, R0 and the average decay lifetime of the nanocrystals showed dependence on concentration. High internal quantum efficiency (IQE) values were obtained at low Eu3+ ion concentrations, but efficiency decreased with increasing ion concentration. The CIE coordinates values were comparable to existing red phosphors and in combination with the high IQE make this phosphor a good candidate for red light emitting applications.

Photoluminescence properties of a new orange-red-emitting Sm(3+)-La3SbO7 phosphor.

PubMed

Li, Zeng-Mei; Deng, Li-Gang; Zhao, Shan-Cang; Zhang, Shu-Qiu; Guo, Chang-Ying; Liang, Jing-Yun; Yue, Hui; Wan, Chun-Yan

2016-03-01

The antimonate compound La3SbO7 has high chemical stability, lattice stiffness and thermal stability. Orange-red-emitting antimonate-based phosphors La3SbO7:xSm(3+) (x = 0.02, 0.05, 0.08, 0.10, 0.15, 0.20 and 0.25) were synthesized. The phase structure and photoluminescence properties of these phosphors were investigated. The emission spectrum obtained on excitation at 407 nm contained exclusively the characteristic emissions of Sm(3+) at 568, 608, 654 and 716 nm, which correspond to the transitions from (4)G5/2 to (6)H5/2, (6)H7/2, (6)H9/2 and (6)H11/2 of Sm(3+), respectively. The strongest emission was located at 608 nm due to the (4)G5/2→(6)H7/2 transition of Sm(3+), generating bright orange-red light. The critical quenching concentration of Sm(3+) in La3SbO7:Sm(3+) phosphor was determined as 10% and the energy transfer between Sm(3+) was found to be through an exchange interaction. The International Commission on Illumination chromaticity coordinates of the La3SbO7:0.10Sm(3+) phosphors are located in the orange-red region. The La3SbO7:Sm(3+) phosphors may be potentially used as red phosphors for white light-emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.

Zero-reabsorption doped-nanocrystal luminescent solar concentrators.

PubMed

Erickson, Christian S; Bradshaw, Liam R; McDowall, Stephen; Gilbertson, John D; Gamelin, Daniel R; Patrick, David L

2014-04-22

Optical concentration can lower the cost of solar energy conversion by reducing photovoltaic cell area and increasing photovoltaic efficiency. Luminescent solar concentrators offer an attractive approach to combined spectral and spatial concentration of both specular and diffuse light without tracking, but they have been plagued by luminophore self-absorption losses when employed on practical size scales. Here, we introduce doped semiconductor nanocrystals as a new class of phosphors for use in luminescent solar concentrators. In proof-of-concept experiments, visibly transparent, ultraviolet-selective luminescent solar concentrators have been prepared using colloidal Mn(2+)-doped ZnSe nanocrystals that show no luminescence reabsorption. Optical quantum efficiencies of 37% are measured, yielding a maximum projected energy concentration of ∼6× and flux gain for a-Si photovoltaics of 15.6 in the large-area limit, for the first time bounded not by luminophore self-absorption but by the transparency of the waveguide itself. Future directions in the use of colloidal doped nanocrystals as robust, processable spectrum-shifting phosphors for luminescent solar concentration on the large scales required for practical application of this technology are discussed.

Reduction and Analysis of Phosphor Thermography Data With the IHEAT Software Package

NASA Technical Reports Server (NTRS)

Merski, N. Ronald

1998-01-01

Detailed aeroheating information is critical to the successful design of a thermal protection system (TPS) for an aerospace vehicle. This report describes NASA Langley Research Center's (LaRC) two-color relative-intensity phosphor thermography method and the IHEAT software package which is used for the efficient data reduction and analysis of the phosphor image data. Development of theory is provided for a new weighted two-color relative-intensity fluorescence theory for quantitatively determining surface temperatures on hypersonic wind tunnel models; an improved application of the one-dimensional conduction theory for use in determining global heating mappings; and extrapolation of wind tunnel data to flight surface temperatures. The phosphor methodology at LaRC is presented including descriptions of phosphor model fabrication, test facilities and phosphor video acquisition systems. A discussion of the calibration procedures, data reduction and data analysis is given. Estimates of the total uncertainties (with a 95% confidence level) associated with the phosphor technique are shown to be approximately 8 to 10 percent in the Langley's 31-Inch Mach 10 Tunnel and 7 to 10 percent in the 20-Inch Mach 6 Tunnel. A comparison with thin-film measurements using two-inch radius hemispheres shows the phosphor data to be within 7 percent of thin-film measurements and to agree even better with predictions via a LATCH computational fluid dynamics solution (CFD). Good agreement between phosphor data and LAURA CFD computations on the forebody of a vertical takeoff/vertical lander configuration at four angles of attack is also shown. In addition, a comparison is given between Mach 6 phosphor data and laminar and turbulent solutions generated using the LAURA, GASP and LATCH CFD codes. Finally, the extrapolation method developed in this report is applied to the X-34 configuration with good agreement between the phosphor extrapolation and LAURA flight surface temperature predictions. The phosphor process outlined in the paper is believed to provide the aerothermodynamic community with a valuable capability for rapidly obtaining (4 to 5 weeks) detailed heating information needed in TPS design.

Cross-sectional study of the association of abomasal displacement or volvulus with serum electrolyte and mineral concentrations in dairy cows.

PubMed Central

Delgado-Lecaroz, R; Warnick, L D; Guard, C L; Smith, M C; Barry, D A

2000-01-01

The objective of this study was to evaluate serum mineral and electrolyte concentrations at the time of on-farm diagnosis of left displaced abomasum, right displaced abomasum, or abomasal volvulus in dairy cows. Data were collected from 104 affected cows and 96 control cows matched with cases, based on herd, parity, and stage of lactation. Cows with abomasal displacement or volvulus had significantly lower calcium, phosphorous, magnesium, potassium, and chloride concentrations and increased anion gap at the time of diagnosis compared with control cows from the same herds. The percentages of cases and controls with total serum calcium concentrations below the lower limit of the laboratory reference range (2.08 mmol/L [8.3 mg/dL]) were 70% and 23%, respectively. Based on the large percentage of cases with hypocalcemia, administering calcium salts at the time of treatment of field cases of abomasal displacement or volvulus may be beneficial. PMID:10769767

Hybrid 2D photonic crystal-assisted Lu3Al5O12:Ce ceramic-plate phosphor and free-standing red film phosphor for white LEDs with high color-rendering index.

PubMed

Park, Hoo Keun; Oh, Ji Hye; Kang, Heejoon; Zhang, Jian; Do, Young Rag

2015-03-04

This paper reports the combined optical effects of a two-dimensional (2D) SiNx photonic crystal layer (PCL)-assisted Lu3Al5O12:Ce (LuAG:Ce) green ceramic-plate phosphor (CPP) and a free-standing (Sr,Ca)AlSiN3:Eu red film phosphor to enhance luminous efficacy, color rendering index (CRI), and special CRI (R9) of LuAG:Ce CPP-capped white light-emitting diodes (LEDs) for high-power white LEDs at 350 mA. By introducing the 2D SiNx PCL, the luminous efficacy was improved by a factor of 1.25 and 1.15 compared to that of the conventional flat CPP-capped LED and the thickness-increased CPP-capped LED (with a thickness of 0.15 mm), respectively, while maintaining low color-rendering properties. The combining of the free-standing red film phosphor in the flat CPP-capped, the 2D PCL-assisted CPP-capped, and the thickness-increased CPP-capped LEDs led to enhancement of the CRI and the special CRI (R9); it also led to a decrease of the correlated color temperature (CCT) due to broad wavelength coverage via the addition of red emission. High CRI (94), natural white CCT (4450 K), and acceptable luminous efficacy (71.1 lm/W) were attained from the 2D PCL-assisted LuAG:Ce CPP/free-standing red film phosphor-based LED using a red phosphor concentration of 7.5 wt %. It is expected that the combination of the 2D PCL and the free-standing red film phosphor will be a good candidate for achieving a high-power white CPP-capped LED with excellent CRI.

Host-Sensitized and Tunable Luminescence of GdNbO4:Ln3+ (Ln3+ = Eu3+/Tb3+/Tm3+) Nanocrystalline Phosphors with Abundant Color.

PubMed

Liu, Xiaoming; Chen, Chen; Li, Shuailong; Dai, Yuhua; Guo, Huiqin; Tang, Xinghua; Xie, Yu; Yan, Liushui

2016-10-17

Up to now, GdNbO 4 has always been regarded as an essentially inert material in the visible region with excitation of UV light and electron beams. Nevertheless, here we demonstrate a new recreating blue emission of GdNbO 4 nanocrystalline phosphors with a quantum efficiency of 41.6% and host sensitized luminescence in GdNbO 4 :Ln 3+ (Ln 3+ = Eu 3+ /Tb 3+ /Tm 3+ ) nanocrystalline phosphors with abundant color in response to UV light and electron beams. The GdNbO 4 and GdNbO 4 :Ln 3+ (Ln 3+ = Eu 3+ /Tb 3+ /Tm 3+ ) nanocrystalline phosphors were synthesized by a Pechini-type sol-gel process. With excitation of UV light and low-voltage electron beams, the obtained GdNbO 4 nanocrystalline phosphor presents a strong blue luminescence from 280 to 650 nm centered around 440 nm, and the GdNbO 4 :Ln 3+ nanocrystalline phosphors show both host emission and respective emission lines derived from the characterize f-f transitions of the doping Eu 3+ , Tb 3+ , and Tm 3+ ions. The luminescence color of GdNbO 4 :Ln 3+ nanocrystalline phosphors can be tuned from blue to green, red, blue-green, orange, pinkish, white, etc. by varying the doping species, concentration, and relative ratio of the codoping rare earth ions in GdNbO 4 host lattice. A single-phase white-light-emission has been realized in Eu 3+ /Tb 3+ /Tm 3+ triply doped GdNbO 4 nanocrystalline phosphors. The luminescence properties and mechanisms of GdNbO 4 and GdNbO 4 :Ln 3+ (Ln 3+ = Eu 3+ /Tb 3+ /Tm 3+ ) are updated.

An experimental and theoretical study of new phosphors for full color field emission displays

NASA Astrophysics Data System (ADS)

Zhang, Fu-Li

An in depth study is reported of the cathodoluminescent (CL) properties of three new highly efficiency blue phosphors for field emission display (FED) applications doped with fast activators. The superior performance of a new Eu-doped green SrGa2S4 will also be reported. This work addresses four main topics: (1) a detailed study of the dependence of the luminescent intensity on activator concentration, as a function of electron beam voltage and current density; (2) the optical properties of thew phosphors and the development of a CL efficiency characterization technique using a critical screen weight method, which can obtain maximum light output and improve measurement accuracy; (3) understanding the low voltage CL mechanism associated with nanocrystal size by developing a thin film and disk model based on transportation theory and experimental results; (4) Development of a comprehensive evaluation method of red, green, and blue (RGB) phosphors for full color displays by calculation of luminance ratios, required luminance, and measurements of spectra, efficiency and saturation behavior. For FEDs which combine the best properties of CRT and flat panel displays, the development of efficient phosphors at low voltages and high current densities is shown to be critical to meet the luminance and power requirement demands for portable displays. Of particular importance is the need for a good blue phosphor, and to understand the dependence of the CL efficiency on nanocrystal size, penetration depth, diffusion length and surface recombination rate. This has been obtained from the thin film and disk models and fits to experiment. Comparisons between full color phosphor sets show that the performance of a display can vary by over a factor of three depending on the choice of the RGB set. Other factors that are important for optimizing the performance of FED phosphors are reviewed.

Synthesis and photoluminescence properties of Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14}:Sm{sup 3+} red phosphor for white light emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Ge; Ci, Zhipeng; Shi, Yurong

2014-07-01

Highlights: • A novel red phosphor Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14}:Sm{sup 3+} was synthesized and investigated firstly. • The structure and characteristic luminescence properties are discussed. • The excellent thermal stability was found and investigated. • It has good color saturation, the CIE is close to that of commercial Y{sub 2}O{sub 3}:Eu{sup 3+}. - Abstract: A series of Sm{sup 3+} doped Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14} red phosphors were successfully synthesized. X-ray diffraction analysis indicates that all the samples are single phased. The luminescence property is investigated in detail by measuring their photoluminescence excitation and emission spectra. Ca{sub 19}Mg{sub 2}(PO{submore » 4}){sub 14}:Sm{sup 3+} phosphors show strong absorption in 400–410 nm region, which is suitable for application in LEDs. When excited at 403 nm, Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14}:Sm{sup 3+} phosphor can emit red emission with CIE chromaticity coordinates (0.615, 0.384). The optimal doping concentration of Sm{sup 3+} doped Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14} is measured to be 0.02. The thermal quenching property is also measured and compared with the commercial red phosphor Y{sub 2}O{sub 3}:Eu{sup 3+} (Topstar, TXC-RIA). The results indicate Ca{sub 19}Mg{sub 2}(PO{sub 4}){sub 14}:Sm{sup 3+} phosphors have potential to serve as a red phosphor for white LEDs.« less

The effects of wildfire on mercury and stable isotopes (δ(15)N, δ(13)C) in water and biota of small boreal, acidic lakes in southern Norway.

PubMed

Moreno, Clara E; Fjeld, Eirik; Lydersen, Espen

2016-03-01

Effects of wildfire on main water chemistry and mercury (Hg) in water and biota were studied during the first 4 post-fire years. After severe water chemical conditions during hydrological events a few months following the wildfire, the major water chemical parameters were close to pre-fire conditions 4 years after the fire. Concentrations of total Hg and methyl Hg in the surface water 4 years after the fire ranged between 1.17-2.63 ng L(-1) and 0.053-0.188 ng L(-1), respectively. Both variables were positive and strongly correlated with total organic carbon (TOC), TOC-related variables (color, UV absorbance), total phosphorous, and total iron. In addition, MeHg was positively correlated with total nitrogen and chlorophyll-a. The concurrence of increased concentrations of nutrients and chlorophyll-a in the lakes, the more enriched δ(15)N-signatures and higher Hg levels in fish 2 years after the fire, might be a result of the wildfire. However, natural factors as year-to-year variations in thermocline depth and suboxic status in the lakes make it difficult to draw any strong conclusions about wildfire effects on Hg in the biota from our investigated lakes.

Aggressive Treatment of Life-Threatening Hypophosphatemia During Recovery From Fulminant Hepatic Failure: A Case Report.

PubMed

Bissell, Brittany D; Davis, Jason E; Flannery, Alexander H; Adkins, David A; Thompson Bastin, Melissa L

2018-06-01

Acute liver failure secondary to acetaminophen overdose can be a life-threatening condition, characterized by severe electrolyte derangements. Hepatocyte regeneration is associated with phosphorous utilization and is a known complication of liver recovery following injury. We report the case of profound, life-threatening hypophosphatemia following recovery from acute fulminant liver failure. As the liver enzymes normalized, serum phosphorous levels plummeted. Our patient required an aggressive, individualized phosphorus replacement regimen, which resulted in a continuous infusion of intravenous (IV) sodium phosphate, titrated to a maximum rate of 30 mmol/h or 0.5 mmol/kg/h. The patient required over 400 mmol of total IV and oral phosphorous over the course of 48 hours. An aggressive approach to phosphorous replacement was done safely and effectively. Traditional replacement protocols are not adequate to sustain patients with this degree of hypophosphatemia. This is the first report to utilize a continuous infusion of phosphate with a maximum reported rate (0.5 mmol/kg/h). Our report summarizes a novel and safe approach for clinicians to maximally support these patients through high-dose, continuous infusion phosphorous administration.

Behavioral-Physiological Effects of Red Phosphorous Smoke Inhalation on Two Wildlife Species. Task 1. Inhalation Equipment Development/Ambient CO evaluation/Aerosol Distribution and Air Quality Study

DTIC Science & Technology

1987-12-01

occurred in only negligible quantities. Carbo /monoxide was found-to occur in measurable amounts during practically all burns , wit average readings of from...generation. This involved a total of 64 RP/BR burns at target concentrations of 0.4, 1.5, and 3.0 mg/l and 3.0, 4.5, and 6.0 mg/l with air-flow rates of...500 and 250 I/min, respectively. Each burn lasted approximately 1 h and 45 min. Spatial uniformity of RP/BR concentra- tion was assessed by sampling

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution.

PubMed

Liu, Hu; Zhang, Shengen; Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin; Volinsky, Alex A

2014-05-15

This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y0.95Eu0.05)2O3 in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce0.67Tb0.33MgAl11O19) and the Blue phosphor (Ba0.9Eu0.1MgAl10O17) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO2 are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications. Copyright © 2014 Elsevier B.V. All rights reserved.

Ba2ZnWO6:Sm3+ as promising orange-red emitting phosphors: Photoluminescence properties and energy transfer process

NASA Astrophysics Data System (ADS)

Chen, Peng; Hu, Wenyuan; Yang, Dingming; Zhu, Jiayi; Zhang, Jing; Wu, Yadong

2018-02-01

Novel orange-red emitting phosphors, Ba2Zn1-xWO6:xSm3+ (x = 0.03, 0.04, 0.05, 0.06 and 0.07) (BZW:Sm3+), were prepared using a high-temperature solid-state reaction method. Their crystal structure and photoluminescence properties were characterized and the mechanism of energy transfers between Ba2ZnWO6 and Sm3+ elucidated in detail. It was found that the phosphors had a cubic structure with space group Fm 3 bar m . They can be excited by near-ultraviolet light, and the characteristic emissions of Sm3+ ions are observed at 564 nm, 598 nm and 645 nm, corresponding to 4G5/2 → 6H5/2, 4G5/2 → 6H7/2 and 4G5/2 → 6H9/2 transitions, respectively. The 4G5/2 → 6H9/2 transitions shows the greatest intensity, which indicates that Sm3+ ions occupy the noncentrosymmetric sites. The optimal doping concentration of Sm3+ ions in Ba2ZnWO6 is about 5 mol% and the phenomenon of concentration quenching occurs when the content of Sm3+ ions exceeds 5 mol%. All results show that the Ba2ZnWO6:Sm3+ phosphor holds great promise for use in high-quality white light-emitting diodes.

In vivo X-Ray excited optical luminescence from phosphor-doped aerogel and Sylgard 184 composites

NASA Astrophysics Data System (ADS)

Allison, Stephen W.; Baker, Ethan S.; Lynch, Kyle J.; Sabri, Firouzeh

2017-06-01

X-Ray excited optical luminescence (XEOL) is a new and noninvasive diagnostic technique suitable for in situ biochemical imaging and disease detection. The X-Ray excited optical luminescence of phosphor doping in crosslinked silica aerogel and Sylgard 184 hosts was investigated in this study. Composite silica aerogels and Sylgard 184 samples of 5%, 15%, and 50% concentrations by weight of La2O2S:Eu phosphor were prepared and inserted subcutaneously in a Sprague-Dawley rat and excited by X-Ray emission at 70 and 100 kV. A fiber optic bundle positioned within 5 mm of the sample collected the luminescence signal and conveyed it to a photomultiplier detector. The signal intensity scaled with dopant concentration. The time dependence of the predominantly red luminescence consisted of 60 cycle bursts of approximately 8 ms duration. The amplitude was modulated at about 10 Hz with a 60% depth. This indicates the time dependence of the X-Ray source. A simulation showed how to observe phosphor decay between individual burst pulses. The emission from the two types of composite samples was easily detected from the outside of the skin layer. Both Sylgard 184 and crosslinked silica aerogels are biocompatible and bio stable materials that could serve a variety of potential XEOL applications. These very strong signals imply potential for creating new In-vivo sensing applications and diagnostic tools.

Nutrients removal in hybrid fluidised bed bioreactors operated with aeration cycles.

PubMed

Martin, Martin; Enríquez, L López; Fernández-Polanco, M; Villaverde, S; Garcia-Encina, P A

2007-01-01

Abstract Two hybrid fluidised bed reactors filled with sepiolite and granular activated carbon (GAC) were operated with short cycled aeration for removing organic matter, total nitrogen and phosphorous, respectively. Both reactors were continuously operated with synthetic and/or industrial wastewater containing 350-500 mg COD/L, 110-130 mg NKT/L, 90-100 mg NH3-N/L and 12-15 mg P/L for 8 months. The reactor filled with sepiolite, treating only synthetic wastewater, removed COD, ammonia, total nitrogen and phosphorous up to 88, 91, 55 and 80% with a hydraulic retention time (HRT) of 10 h, respectively. These efficiencies correspond to removal rates of 0.95 kgCODm(-3)d(-1) and 0.16 kg total N m(-3)d(-1). The reactor filled with GAC was operated for 4 months with synthetic wastewater and 4 months with industrial wastewater, removing 98% of COD, 96% of ammonia, and 66% of total nitrogen, with an HRT of 13.6 h. No significant phosphorous removing activity was observed in this reactor. Microbial communities growing with both reactors were followed using polymerase chain reaction (PCR) and denaturing gradient gel electrophoresis (DGGE) techniques. The microbial fingerprints, i.e. DGGE profiles, indicated that biological communities in both reactors were stable along the operational period even when the operating conditions were changed.

Inhomogenous Broadening, Charge Compensation, and Luminescence Quenching in Ce 3+-Doped Sr 3AlO 4F Phosphors

DOE PAGES

Setlur, A. A.; Porob, D. G.; Happek, U.; ...

2015-09-24

The local coordination around luminescent ions in phosphors can affect the properties of these materials. Here, we analyze the Ce 3+ luminescence for the various Ce 3+ centers in Sr 3AlO 4F-based phosphors and use the excitation, emission, and quenching of these phosphors to infer aspects of the local coordination. It is shown that Ce 3+ centers with lower energy 4f 1→5d 1 absorption bands are likely from charge compensation effects by the replacement of F - by O 2-. In addition, at higher RE 3+ concentrations, additional Ce 3+ centers with even lower energy 4f 1→5d 1 absorption bandsmore » are present, presumably due to Ce 3+-RE 3+ pair formation and O 2- charge compensation. These Ce 3+ centers with lower energy 4f 1→5d 1 absorption bands have their luminescence strongly quenched at room temperature. The relationships between composition and Ce 3+ luminescence quenching for Sr 3AlO 4F-based phosphors are also discussed, giving evidence that Ce 3+(5d 1) ionization is the main cause for luminescence quenching in these materials.« less

Tunable photoluminescence and magnetic properties of Dy(3+) and Eu(3+) doped GdVO4 multifunctional phosphors.

PubMed

Liu, Yanxia; Liu, Guixia; Dong, Xiangting; Wang, Jinxian; Yu, Wensheng

2015-10-28

A series of Dy(3+) or/and Eu(3+) doped GdVO4 phosphors were successfully prepared by a simple hydrothermal method and characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectrometry (EDS), photoluminescence (PL) spectroscopy and vibrating sample magnetometry (VSM). The results indicate that the as-prepared samples are pure tetragonal phase GdVO4, taking on nanoparticles with an average size of 45 nm. Under ultraviolet (UV) light excitation, the individual Dy(3+) or Eu(3+) ion activated GdVO4 phosphors exhibit excellent emission properties in their respective regions. The mechanism of energy transfer from the VO4(3-) group and the charge transfer band (CTB) to Dy(3+) and Eu(3+) ions is proposed. Color-tunable emissions in GdVO4:Dy(3+),Eu(3+) phosphors are realized through adopting different excitation wavelengths or adjusting the appropriate concentration of Dy(3+) and Eu(3+) when excited by a single excitation wavelength. In addition, the as-prepared samples show paramagnetic properties at room temperature. This kind of multifunctional color-tunable phosphor has great potential applications in the fields of photoelectronic devices and biomedical sciences.

Luminescence properties of Na3SrB5O10:Dy3+ plate-like microstructures for solid state lighting applications

NASA Astrophysics Data System (ADS)

Dillip, G. R.; Dhoble, S. J.; Raju, B. Deva Prasad

2013-10-01

A series of novel plate-like microstructure Na3SrB5O10 doped with various Dy3+ ions concentration have been synthesized for the first time by solid-state reaction (SSR) method. X-ray diffraction (XRD) results demonstrated that the prepared Na3SrB5O10:Dy3+ phosphors are single-phase pentaborates with triclinic structure. The plate-like morphology of the phosphor is examined by Field emission scanning electron microscopy (FE-SEM). The existence of both BO3 and BO4 groups in Na3SrB5O10:Dy3+ phosphors are identified by Fourier transform infrared (FT-IR) spectroscopy. Upon excitation at 385 nm, the PL spectra mainly comprising of two broad bands: one is a blue light emission (˜486 nm) and another is a yellow light emission (˜581 nm), originating from the transitions of 4F9/2 → 6H15/2 and 4F9/2 → 6H13/2 in 4f9 configuration of Dy3+ ions, respectively and the optimized dopant concentration is determined to be 3 at.%. Interestingly, the yellow-to-blue (Y/B) emission integrated intensity ratio is close to unity (0.99) for 3 at.% Dy3+ ions, suggesting that the phosphors are favor for white illumination. Moreover, the calculated Commission International de l'Eclairage (CIE) chromaticity coordinates of Na3SrB5O10:Dy3+ phosphors shows the values lie in white light region and the estimated CCT values are located in cool/day white light region.

Synthesis and photoluminescence properties of multicolor tunable GdNbO4: Tb3+, Eu3+ phosphors based on energy transfer

NASA Astrophysics Data System (ADS)

Zhang, Lu; Yi, Shuangping; Hu, Xiaoxue; Liang, Boxin; Zhao, Weiren; Wang, Yinhai

2017-03-01

A color-tunable phosphor based on Tb3+/Eu3+ co-doped GdNbO4 were synthesized by a traditional solid-state reaction method. X-ray powder diffraction (XRD), diffuse reflectance spectra, photoluminescence spectra and decay curves were utilized to characterize the as-prepared phosphors. XRD result indicated that various concentrations Tb3+/Eu3+ single-doped and co-doped phosphors were well indexed to the pure GdNbO4 phase. The GdNbO4 host was proved to be a self-activated phosphor with broad absorption range from 200 nm to 325 nm. When Tb3+ ions were added into the host lattice, the energy transferring from host to Tb3+ was identified. And the broad absorption in the UV region was changed and enhanced. Therefore, we selected Tb3+ as the sensitizer ion, and adjusted red component from Eu3+ to control the emission color. The energy transfer from Tb3+ to Eu3+ was confirmed based on the luminescence spectra and decay curves. Furthermore, the energy transmission mechanism was deduced to be the dipole-quadrupole interaction. On the whole, the obtained GdNbO4, GdNbO4:Tb3+, and GdNbO4:Tb3+, Eu3+ phosphors may have potential application in the UV white-light-emitting diodes (w-LEDs) and display devices.

Synthesis and luminescent properties of Tb3Al5O12:Ce3+ phosphors for warm white light emitting diodes

NASA Astrophysics Data System (ADS)

Meng, Qinghuan; Liu, Ying; Fu, Yujie; Zu, Yuangang; Zhou, Zhenbao

2018-01-01

A series of Tb3Al5O12:Ce3+ phosphors were successfully synthesized by a precipitation method. The pure Tb3Al5O12 phase was obtained in the synthesized Tb3Al5O12:Ce3+ phosphors after heat treatments at 500 °C in air for 3 h. The excitation spectra of Tb3Al5O12:Ce3+ phosphors include excitation bands corresponding to Tb3+ and Ce3+ ions. Under the excitation at 455 nm, Tb3Al5O12:Ce3+ phosphors show emission band at around 553 nm. The critical doping concentration of Ce3+ in Tb3Al5O12 is 6mol%, which shows the highest emission intensity. White light-emitting diodes were fabricated by combining InGaN-based blue light-emitting diodes with Tb3Al5O12:Ce3+ and Y3Al5O12:Ce3+ phosphors. The Tb3Al5O12:Ce3+ based white light-emitting diode shows a lower color temperature than that of Y3Al5O12:Ce3+ based white light-emitting diode. The experimental results clearly indicate that the prepared Tb3Al5O12:Ce3+ has potential applications in white light emitting diodes.

Dispersion of fine phosphor particles by newly developed beads mill

NASA Astrophysics Data System (ADS)

Joni, I. Made; Panatarani, C.; Maulana, Dwindra W.

2016-02-01

Fine phosphor Y2O3:Eu3+ particles has advanced properties compare to conventional particles applied for compact fluorescent lamp (CFL) as three band phosphor. However, suspension of fine particles easily agglomerated during preparation of spray coating of the CFL tube. Therefore, it is introduced newly developed beads mill system to disperse fine phosphor. The beads mill consist of glass beads, dispersing chamber (impellers), separator chamber, slurry pump and motors. The first important performance of beads mill is the performance of the designed on separating the beads with the suspended fine particles. We report the development of beads mill and its separation performance vary in flow rate and separator rotation speeds. The 27 kg of glass beads with 30 µm in size was poured into dispersing chamber and then water was pumped continuously through the slurry pump. The samples for the separation test was obtained every 1 hours vary in rotation speed and slurry flow rate. The results shows that the separation performance was 99.99 % obtained for the rotation speed of >1000 rpm and flow rate of 8 L/minute. The performances of the system was verified by dispersing fine phosphor Y2O3:Eu3+ particles with concentration 1 wt.%. From the observed size distribution of particles after beads mill, it is concluded that the current design of bead mill effectively dispersed fine phosphor Y2O3:Eu3+.

Development of Eu3+ activated monoclinic, perovskite, and garnet compounds in the Gd2O3-Al2O3 phase diagram as efficient red-emitting phosphors

NASA Astrophysics Data System (ADS)

Li, Jinkai; Li, Ji-Guang; Li, Jing; Liu, Shaohong; Li, Xiaodong; Sun, Xudong; Sakka, Yoshio

2013-10-01

Eu3+ doped Gd4Al2O9 (GdAM), GdAlO3 (GdAP), and Gd3Al5O12 (GdAG, containing 10 at% of Lu3+ for lattice stabilization) have been developed in this work as efficient red-emitting phosphors. With coprecipitated carbonate precursors, phase evolution studies found minimum processing temperatures of ~1000, 1100, and 1300 °C for the three phosphors to crystallize as pure phases, respectively. Compared with their yttrium aluminate counterparts, the gadolinium-based phosphors exhibit red-shifted O2--Eu3+ charge transfer excitation band (CTB) centers due to the lower electronegativity of Gd3+ and appreciably higher quantum yields of photoluminescence owing to the occurrence of efficient Gd3+→Eu3+energy transfer. The optimal Eu3+ contents were determined to be ~7.5 at% for GdAM and 5.0 at% for both GdAP and GdAG, and concentration quenching of luminescence was suggested to be due to exchange interactions. Fluorescence decay analysis found a shorter lifetime for the phosphor powder processed at a higher temperature or with a higher Eu3+ content, and the underlying mechanism was discussed. Fluorescence lifetimes were also compared between the yttrium and gadolinium phosphor systems for the dominant emissions.

Phytotoxicity testing of winery wastewater for constructed wetland treatment.

PubMed

Arienzo, Michele; Christen, Evan W; Quayle, Wendy C

2009-09-30

Rapid and inexpensive phytotoxicity bioassays for winery wastewater (WW) are important when designing winery wastewater treatment systems involving constructed wetlands. Three macrophyte wetland species (Phragmites australis, Schoenoplectus validus and Juncus ingens) were tested using a pot experiment simulating a wetland microcosm. The winery wastewater concentration was varied (0.5%, 5%, 10%, 25%, 50%, 75% and 100%) and pH was corrected for some concentrations using lime as an amendment. The tolerance of the three aquatic macrophytes species to winery wastewater was studied through biomass production, total chlorophyll and nitrogen, phosphorous and potassium tissue concentrations. The results showed that at greater than 25% wastewater concentration all the macrophytes died and that Phragmites was the least hardy species. At less than 25% wastewater concentration the wetland microcosms were effective in reducing chemical oxygen demand, phenols and total soluble solids. We also evaluated the performance of two laboratory phytotoxicity assays; (1) Garden Cress (Lepidium sativum), and (2) Onion (Allium coepa). The results of these tests revealed that the effluent was highly toxic with effective concentration, EC(50), inhibition values, as low as 0.25%. Liming the WW increased the EC(50) by 10 fold. Comparing the cress and onion bioassays with the wetland microcosm results indicated that the thresholds for toxicity were of the same order of magnitude. As such we suggest that the onion and cress bioassays could be effectively used in the wine industry for rapid wastewater toxicity assessment.

Post-treatment of secondary wastewater treatment plant effluent using a two-stage fluidized bed bioreactor system

PubMed Central

2013-01-01

The aim of this study was to investigate the performance of a two-stage fluidized bed reactor (FBR) system for the post-treatment of secondary wastewater treatment plant effluents (Shahrak Gharb, Tehran, Iran). The proposed treatment scheme was evaluated using pilot-scale reactors (106-L of capacity) filled with PVC as the fluidized bed (first stage) and gravel for the filtration purpose (second stage). Aluminum sulfate (30 mg/L) and chlorine (1 mg/L) were used for the coagulation and disinfection of the effluent, respectively. To monitor the performance of the FBR system, variation of several parameters (biochemical oxygen demand (BOD5), chemical oxygen demand (COD), turbidity, total phosphorous, total coliform and fecal coliform) were monitored in the effluent wastewater samples. The results showed that the proposed system could effectively reduce BOD5 and COD below 1.95 and 4.06 mg/L, respectively. Turbidity of the effluent could be achieved below 0.75 NTU, which was lower than those reported for the disinfection purpose. The total phosphorus was reduced to 0.52 mg/L, which was near the present phosphorous standard for the prevention of eutrophication process. Depending on both microorganism concentration and applied surface loading rates (5–10 m/h), about 35 to 75% and 67 to 97% of coliform were removed without and with the chlorine addition, respectively. Findings of this study clearly confirmed the efficiency of the FBR system for the post-treatment of the secondary wastewater treatment plant effluents without any solid problem during the chlorination. PMID:24499570

Subclinical hypocalcaemia in captive Asian elephants (Elephas maximus).

PubMed

van der Kolk, J H; van Leeuwen, J P T M; van den Belt, A J M; van Schaik, R H N; Schaftenaar, W

2008-04-12

The hypothesis that hypocalcaemia may play a role in dystocia in captive Asian elephants (Elephas maximus) was investigated. The objectives of the study were to measure the total calcium concentration in elephant plasma; assess the changes in parameters of calcium metabolism during a feeding trial; investigate a possible relationship between calcium metabolism and dystocia; and assess bone mineralisation in captive Asian elephants in vivo. The following parameters were measured: total and ionised calcium, inorganic phosphorous and magnesium, the fractional excretions of these minerals, intact parathyroid hormone, 25-OH-D(3) and 1,25-OH-D(3). Radiographs were taken from tail vertebrae for assessment of bone mineralisation. The mean (sd) heparinised plasma total calcium concentration was 2.7 (0.33) mmol/l (n=43) ranging from 0.84 to 3.08 mmol/l in 11 Asian elephants. There was no significant correlation between plasma total calcium concentration and age. Following feeding of a calcium rich ration to four captive Asian elephant cows, plasma total and ionised calcium peaked at 3.6 (0.24) mmol/l (range 3.4 to 3.9 mmol/l) and 1.25 (0.07) mmol/l (range 1.17 to 1.32 mmol/l), respectively. Plasma ionised calcium concentrations around parturition in four Asian elephant cows ranged from 0.37 to 1.1 mmol/l only. The present study indicates that captive Asian elephants might be hypocalcaemic, and that, in captive Asian elephants, the normal plasma concentration of total calcium should actually be around 3.6 mmol/l and normal plasma concentration of ionised calcium around 1.25 mmol/l. Given the fact that elephants absorb dietary calcium mainly from the intestine, it could be concluded that elephants should be fed calcium-rich diets at all times, and particularly around parturition. In addition, normal values for ionised calcium in captive Asian elephants should be reassessed.

Solubility limits of dibutyl phosphoric acid in uranium-nitric acid solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.A.

2000-01-04

The Savannah River Site has enriched uranium (EU) solution that has been stored since being purified in its solvent extraction processes. The concentrations in solution are approximately 6 g/L U and 0.1 M nitric acid. Residual tributylphosphate in solution has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 30--50 mg/L. Dibutyl phosphoric acid, in turn, is in equilibrium with (HDBP){sub 2} and DBP{sup {minus}}. Uranium can form compounds with the dibutylphosphate ion (DBP{sup {minus}}) which have limited solubility, thereby creating a nuclear criticality safety issue. Literature reports and earlier SRTC tests have shown that it is feasiblemore » to precipitate U-DBP solid during the storage and processing of EU solutions. As a result, a series of solubility experiments were run at nitric acid concentrations from 0--4.0 M HNO{sub 3}, uranium at 0--90 g/L, and temperatures from 0--30 C. The data shows temperature and nitric acid concentration dependence consistent with what would be expected. With respect to uranium concentration, U-DBP solubility passes through a minimum between 6 and 12 g/L U at the acid concentrations and temperatures studied. However, the minimum shows a slight shift toward lower uranium concentrations at lower nitric acid concentrations. The shifts in solubility are strongly dependent upon the overall ionic strength of the solution. The data also reveal a shift to higher DBP solubility above 0.5 M HNO{sub 3} for both 6 g/L and 12 g/L uranium solutions. Analysis of U-DBP solids from the tests identified distinct differences between precipitates from less than 0.5 M solutions and those from greater than 4 M acid. Analyses identified UO{sub 2}(DBP){sub 2} as the dominant compound present at low acid concentrations in accordance with literature reports. As the acid concentration increases, the crystalline UO{sub 2}(DBP){sub 2} shows molecular substitutions and an increase in amorphous content.« less

Efficiency of temporary storage of geothermal waters in a lake system: Monitoring the changes of water quality and bacterial community structures.

PubMed

Szirányi, Barbara; Krett, Gergely; Kosáros, Tünde; Janurik, Endre; Pekár, Ferenc; Márialigeti, Károly; Borsodi, Andrea K

2017-12-01

Disposal of used geothermal waters in Hungary often means temporary storage in reservoir lakes to reduce temperature and improve water quality. In this study, the physical and chemical properties and changes in the bacterial community structure of a reservoir lake system in southeast region of Hungary were monitored and compared through 2 years, respectively. The values of biological oxygen demand, concentrations of ammonium ion, total inorganic nitrogen, total phosphorous, and total phenol decreased, whereas oxygen saturation, total organic nitrogen, pH, and conductivity increased during the storage period. Bacterial community structure of water and sediment samples was compared by denaturing gradient gel electrophoresis (DGGE) following the amplification of the 16S rRNA gene. According to the DGGE patterns, greater seasonal than spatial differences of bacterial communities were revealed in both water and sediment of the lakes. Representatives of the genera Arthrospira and Anabaenopsis (cyanobacteria) were identified as permanent and dominant members of the bacterial communities.

Highly Efficient Green-Emitting Phosphors Ba2Y5B5O17 with Low Thermal Quenching Due to Fast Energy Transfer from Ce3+ to Tb3.

PubMed

Xiao, Yu; Hao, Zhendong; Zhang, Liangliang; Xiao, Wenge; Wu, Dan; Zhang, Xia; Pan, Guo-Hui; Luo, Yongshi; Zhang, Jiahua

2017-04-17

This paper demonstrates a highly thermally stable and efficient green-emitting Ba 2 Y 5 B 5 O 17 :Ce 3+ , Tb 3+ phosphor prepared by high-temperature solid-state reaction. The phosphor exhibits a blue emission band of Ce 3+ and green emission lines of Tb 3+ upon Ce 3+ excitation in the near-UV spectral region. The effect of Ce 3+ to Tb 3+ energy transfer on blue to green emission color tuning and on luminescence thermal stability is studied in the samples codoped with 1% Ce 3+ and various concentrations (0-40%) of Tb 3+ . The green emission of Tb 3+ upon Ce 3+ excitation at 150 °C can keep, on average, 92% of its intensity at room temperature, with the best one showing no intensity decreasing up to 210 °C for 30% Tb 3+ . Meanwhile, Ce 3+ emission intensity only keeps 42% on average at 150 °C. The high thermal stability of the green emission is attributed to suppression of Ce 3+ thermal de-excitation through fast energy transfer to Tb 3+ , which in the green-emitting excited states is highly thermally stable such that no lifetime shortening is observed with raising temperature to 210 °C. The predominant green emission is observed for Tb 3+ concentration of at least 10% due to efficient energy transfer with the transfer efficiency approaching 100% for 40% Tb 3+ . The internal and external quantum yield of the sample with Tb 3+ concentration of 20% can be as high as 76% and 55%, respectively. The green phosphor, thus, shows attractive performance for near-UV-based white-light-emitting diodes applications.

Simultaneous determination of total nitrogen and total phosphorus in environmental waters using alkaline persulfate digestion and ion chromatography.

PubMed

De Borba, Brian M; Jack, Richard F; Rohrer, Jeffrey S; Wirt, Joan; Wang, Dongmei

2014-11-21

An ion chromatography (IC) method was developed for the simultaneous determination of total nitrogen and total phosphorus after alkaline persulfate digestion. This study takes advantage of advances in construction of high-resolution, high-capacity anion-exchange columns that can better tolerate the matrices typically encountered when a determination of total nitrogen and total phosphorous is required. Here, we used an electrolytically generated hydroxide eluent combined with a high-capacity, hydroxide-selective, anion-exchange column for the determination of total nitrogen (as nitrate-N) and total phosphorus (as phosphate-P) in environmental samples by IC. This method yielded LODs for nitrate-N and phosphate-P of 1.0 and 1.3 μg/L, respectively. The LOQs determined for these analytes were 3.4 and 4.2 μg/L, respectively. Due to the dilution factor required and the blank nitrate-N concentration after the persulfate digestion, the quantification limits increased for nitrate-N and phosphate-P to 171 and 63 μg/L, respectively. The suitability of the method was evaluated by determining the nitrogen and phosphorus concentrations from known concentrations of organic-containing nitrogen and phosphorus compounds. In addition, environmental samples consisting of six different wastewaters and 48 reservoir samples were evaluated for total nitrogen and phosphorus. The recoveries of nitrogen and phosphorus from the organic-containing compounds ranged from 93.1 to 100.1% and 85.2 to 97.1%, respectively. In addition, good correlation between results obtained by the colorimetric method and IC was also observed. The linearity, accuracy, and evaluation of potential interferences for determining TN and TP will be discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of effluent spray irrigation on ground water at a test site near Tarpon Springs, Florida

USGS Publications Warehouse

Brown, D.P.

1982-01-01

Secondary-treated effluent was applied to a 7.2-acre test site near Tarpon Springs, Fla., for about 1 year at an average rate of 0.06 million gallons per day and 3 years at 0.11 million gallons per day. Chemical fertilizer was applied periodically to the test site and adjacent areas. Periodic mounding of the water table occurred due to effluent irrigation, inducing radial flow from the test site. Physical, geochemical, biochemical processes effectively reduced total nitrogen concentration 90% and total phosphorous concentration more than 95% in the ground water of the surficial aquifer about 300 feet downgradient from the test site from that of the applied effluent. Downgradient, total nitrogen averaged 2.4 milligrams per liter and total phosphorus averaged 0.17 milligrams per liter. Substantial increases in total phosphorus were observed when the pH of the ground water increased. Total coliform bacteria in the ground water of the surficial aquifer were generally less than 100 colonies per 100 milliliters. Fecal coliform bacteria were generally less than 25 colonies per 100 milliliters at the test site and were not detected downgradient or near the test site. Fecal streptococcal bacteria were generally less than 100 colonies per 100 milliliters at the test site, but were detected on three occasions near the test site. (USGS)

Synthesis and photoluminescence properties of Dy{sup 3+} doped white light emitting CdTa{sub 2}O{sub 6} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

İlhan, Mustafa, E-mail: mustafa.ilhan@marmara.edu.tr; Ekmekçi, Mete Kaan

2015-03-15

The undoped and CdTa{sub 2}O{sub 6}:Dy{sup 3+} (0.2≤x≤2.0 mol%) phosphors were synthesized at 1100 °C for 12 h by the conventional solid state reaction method. The synthesized CdTa{sub 2}O{sub 6}:Dy{sup 3+} phosphors were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS) and Photoluminescence (PL) analyses. The PL spectra showed the presence of excitation peaks between 310 and 440 nm due to the 4f–4f transitions of Dy{sup 3+}. The emission of Dy{sup 3+} ions at 353.0 nm excitation was observed at 487.1 nm (blue) and 577.8 nm (yellow) due to the {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2}more » transitions and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} transitions, respectively. The PL analysis results also showed that the emissions increase with the increasing Dy{sup 3+} ion content. The emissions increased with the doping concentration of up to 1 mol%, and above this level decreased due to concentration quenching effect. The CIE chromaticity color coordinates (x,y) of the CdTa{sub 2}O{sub 6}:Dy{sup 3+} phosphors were found to be in the white light region of the chromaticity diagram. - Graphical abstract: Emission spectra at λ{sub ex}=353.0 nm and CIE chromaticity coordinate diagram of CdTa{sub 2}O{sub 6}:Dy{sup 3+} phosphors. - Highlights: • Pure and CdTa{sub 2}O{sub 6}:Dy{sup 3+} was produced by solid state reaction method. • CdTa{sub 2}O{sub 6}:Dy{sup 3+} phosphor exhibited blue and yellow emissions due to the {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} transitions. • The CCT value for 1.0 mol% CdTa{sub 2}O{sub 6}:Dy{sup 3+} was 5133 K which was located in the cool white daylight region. • Dy{sup 3+} doped CdTa{sub 2}O{sub 6} phosphor has potential in the production of white LEDs.« less

A modeling understanding on the phosphorous removal performances of A2O and reversed A2O processes in a full-scale wastewater treatment plant.

PubMed

Xie, Wen-Ming; Zeng, Raymond J; Li, Wen-Wei; Wang, Guo-Xiang; Zhang, Li-Min

2018-05-31

Reversed A 2 O process (anoxic-anaerobic-aerobic) and conventional A 2 O process (anaerobic-anoxic-aerobic) are widely used in many wastewater treatment plants (WWTPs) in Asia. However, at present, there are still no consistent results to figure out which process has better total phosphorous (TP) removal performance and the mechanism for this difference was not clear yet. In this study, the treatment performances of both processes were compared in the same full-scale WWTP and the TP removal dynamics was analyzed by a modeling method. The treatment performance of full-scale WWTP showed the TP removal efficiency of the reversed A 2 O process was more efficient than in the conventional A 2 O process. The modeling results further reveal that the TP removal depends highly on the concentration and composition of influent COD. It had more efficient TP removal than the conventional A 2 O process only under conditions of sufficient influent COD and high fermentation products content. This study may lay a foundation for appropriate selection and optimization of treatment processes to suit practical wastewater properties.

Solvent directed morphologies and enhanced luminescent properties of BaWO4:Tm3+,Dy3+ for white light emitting diodes

NASA Astrophysics Data System (ADS)

Wu, Hongyue; Yang, Junfeng; Wang, Xiaoxue; Gan, Shucai; Li, Linlin

2018-05-01

A series of Tm3+ and Dy3+ codoped BaWO4 phosphors with tunable shapes were controllably synthesized by a facile solvothermal method. The effects of ratio of ethylene glycol (EG) and water on the morphologies of BaWO4 structures are systematically studied. It was discovered that the reason for these morphological changes is based on the reaction speed of the kinetic control, which relates to the strong chelating abilities of ethylene glycol. And when the solvent is pure ethylene glycol, the peanut-like BaWO4:Dy3+ has the strongest emission intensity. Moreover, the emission color of the phosphors varied from blue (0.232, 0.180) to white (0.268, 0.250) by controlling Dy3+ ions content with a fixed Tm3+ concentration. The energy transfer mechanism was investigated in detail. With increasing the doped concentration of Dy3+ ions, the energy transfer efficiency of BaWO4:0.005Tm3+,yDy3+ increased gradually and reached as high as 63% when the Dy3+ doped concentration is 0.03. The critical distance RC calculated by the spectral overlap method is about 19.93 Å, and it is in good agreement with that obtained using the concentration quenching method (19.70 Å), indicating that the electric dipole-dipole interaction is the main energy transfer mechanism for BaWO4:Tm3+,Dy3+ phosphors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pathak, A. A., E-mail: anuapathak@yahoo.com; Yadav, P. J.; Talewar, R. A.

Blue-emitting phosphor LaMgAl{sub 11}O{sub 19}:Eu{sup 2+} has been synthesized successfully at 500 °C by one step combustion synthesis method. The as-synthesized materials were characterized by powder x-ray diffraction (XRD) and photoluminescence (PL) techniques. Upon 365 nm excitation, emission spectra of the LaMgAl{sub 11}O{sub 19}:Eu{sup 2+} phosphors show a blue band at 450 nm. The excitation spectra corresponding to 4f{sup 7}-4f{sup 6}5d transition of Eu{sup 2+} cover the spectral range of 280–430 nm. The concentration quenching of Eu{sup 2+} in the LaMgAl{sub 11}O{sub 19} host was determined to be 3 mol%. The CIE chromaticity of LAM: Eu{sup 2+} phosphors was compared with the commercial BAM.

Microgreens of brassicaceae: mineral composition and content of 30 varieties

USDA-ARS?s Scientific Manuscript database

The aim of the present study was to analyze the mineral content and concentration of 30 species of microgreens, representative 10 genera of the Brassicaceae family. Brassicaceae microgreens were assayed for concentrations of macroelements, including calcium (Ca), magnesium (Mg), phosphorous (P), sod...

Percentile Distributions of Median Nitrite Plus Nitrate as Nitrogen, Total Nitrogen, and Total Phosphorus Concentrations in Oklahoma Streams, 1973-2001

USGS Publications Warehouse

Haggard, Brian E.; Masoner, Jason R.; Becker, Carol J.

2003-01-01

Nutrients are one of the primary causes of water-quality impairments in streams, lakes, reservoirs, and estuaries in the United States. The U.S. Environmental Protection Agency has developed regional-based nutrient criteria using ecoregions to protect streams in the United States from impairment. However, nutrient criteria were based on nutrient concentrations measured in large aggregated nutrient ecoregions with little relevance to local environmental conditions in states. The Oklahoma Water Resources Board is using a dichotomous process known as Use Support Assessment Protocols to define nutrient criteria in Oklahoma streams. The Oklahoma Water Resources Board is modifying the Use Support Assessment Protocols to reflect nutrient informa-tion and environmental characteristics relevant to Oklahoma streams, while considering nutrient information grouped by geographic regions based on level III ecoregions and state boundaries. Percentile distributions of median nitrite plus nitrate as nitrogen, total nitrogen, and total phosphorous concentrations were calculated from 563 sites in Oklahoma and 4 sites in Arkansas near the Oklahoma and Arkansas border to facilitate development of nutrient criteria for Oklahoma streams. Sites were grouped into four geographic regions and were categorized into eight stream categories by stream slope and stream order. The 50th percentiles of median nitrite plus nitrate as nitrogen, total nitrogen, and total phosphorus concentrations were greater in the Ozark Highland ecoregion and were less in the Ouachita Mountains ecoregion when compared to other geographic areas used to group sites. The 50th percentiles of median concentrations of nitrite plus nitrate as nitrogen, total nitrogen, and total phosphorus were least in first, second, and third order streams. The 50th percentiles of median nitrite plus nitrate as nitrogen, total nitrogen and total phosphorus concentrations in the Ozark Highland and Ouachita Mountains ecoregions were least in first, second, and third order streams with streams slopes greater than 17 feet per mile. Nitrite plus nitrate as nitrogen and total nitrogen criteria determined by the U.S. Environmental Protection Agency for the Ozark Highland ecoregion were less than the 25th percentiles of median nitrite plus nitrate as nitrogen, total nitrogen, and total phosphorus concentrations in the Ozark Highland ecoregion calculated for this report. Nitrite plus nitrate as nitrogen and total nitrogen criteria developed by the U.S. Environmental Protection Agency for the Ouachita Mountains ecoregion were similar to the 25th percentiles of median nitrite plus nitrate as nitrogen and total nitrogen concentrations in the Ouachita Mountains ecoregion calculated for this report. Nitrate as nitrogen and total phosphorus concentrations currently (2002) used in the Use Support Assessment Protocols for Oklahoma were greater than the 75th percentiles of median nitrite plus nitrate as nitrogen and total phosphorus concentrations calculated for this report.

Photovoltaic Performance Enhancement of Silicon Solar Cells Based on Combined Ratios of Three Species of Europium-Doped Phosphors.

PubMed

Ho, Wen-Jeng; You, Bang-Jin; Liu, Jheng-Jie; Bai, Wen-Bin; Syu, Hong-Jhang; Lin, Ching-Fuh

2018-05-18

This paper presents a scheme for the enhancement of silicon solar cells in terms of luminescent emission band and photovoltaic performance. The proposed devices are coated with an luminescent down-shifting (LDS) layer comprising three species of europium (Eu)-doped phosphors mixed within a silicate film (SiO₂) using a spin-on film deposition. The three species of phosphor were mixed at ratios of 0.5:1:1.5, 1:1:1, or 1.5:1:0.5 in weight percentage (wt %). The total quantity of Eu-doped phosphors in the silicate solution was fixed at 3 wt %. The emission wavelengths of the Eu-doped phosphors were as follows: 518 nm (specie-A), 551 nm (specie-B), and 609 nm (specie-C). We examined the extended luminescent emission bands via photoluminescence measurements at room temperature. Closely matching the luminescent emission band to the high responsivity band of the silicon semiconductor resulted in good photovoltaic performance. Impressive improvements in efficiency were observed in all three samples: 0.5:1:1.5 (20.43%), 1:1:1 (19.67%), 1.5:1:0.5 (16.81%), compared to the control with a layer of pure SiO₂ (13.80%).

Luminescence properties of phosphate phosphor Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Fu; Liu, Yufeng, E-mail: liuyufeng4@126.com; Tian, Xiaodong

2015-05-15

A series of reddish orange-emitting phosphate phosphors Ba{sub 3}Y{sub 1−x}(PO{sub 4}){sub 3}:xSm{sup 3+}(0.01≤x≤0.20) were synthesized by solid-state reaction. X-ray diffraction and photoluminescence spectra were utilized to characterize the structure and luminescence properties of as-synthesized phosphors. The optimized phosphors Ba{sub 3}Y{sub 0.95}(PO{sub 4}){sub 3}:0.05Sm{sup 3+} present several excitation bands from 300 to 500 nm, and exhibit intense reddish orange-emitting properties. The energy transfer type between Sm{sup 3+} ions was confirmed as d–d interaction by using Van Uitert model. The chromatic properties of the typical sample Ba{sub 3}Y(PO{sub 4}){sub 3}:0.05Sm{sup 3+} phosphor have been found to have chromaticity coordinates of (0.583, 0.405),more » which are located in reddish orange region under the excitation of 401 nm. These results indicated that Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors have potential applications in the field of lighting and display due to their effective excitation in the near-ultraviolet range. - Graphical abstract: The color coordinates for 5 mol% Sm{sup 3+} doped Ba{sub 3}Y(PO{sub 4}){sub 3} phosphor were calculated to be (0.583, 0.405), which are located in reddish orange region under the excitation of 401 nm. The peaks of Ba{sub 3}Y{sub 0.95}(PO{sub 4}){sub 3}:0.05Sm{sup 3+} phosphor with the highest emission intensity at 600 nm are broader than those of Y{sub 2}O{sub 3}:Eu{sup 3+} and Y{sub 2}O{sub 2}S:Eu{sup 3+} phosphors. All these characteristics suggest that Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors are suitable for near-UV (370–410 nm) excitation and can be applicable to near UV-based WLEDs. ▪ - Highlights: • Different concentration Sm{sup 3+}-doped Ba{sub 3}Y(PO{sub 4}){sub 3} phosphors were fabricated by solid state method. • The optimized phosphors present the several excitation bands from 300 to 500 nm. • The Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} shows bright reddish orange emissions under 401 nm excitation.« less

Effects of chromium and chromium + vitamin C combination on metabolic, oxidative, and fear responses of broilers transported under summer conditions

NASA Astrophysics Data System (ADS)

Perai, A. H.; Kermanshahi, H.; Moghaddam, H. Nassiri; Zarban, A.

2015-04-01

A total of 240 female broilers (42 days old) were randomly assigned to four groups with six replicates and fed either a basal diet (two control groups) or a basal diet supplemented with either 1,200 μg Cr+3 from chromium (Cr) methionine/kg (Cr group) or 1,200 μg Cr+3 from Cr methionine plus 800 mg vitamin C (Vit C)/kg of diet (Cr + Vit C group). After 7 days on the dietary treatment, all groups except one of the controls were transported for 3 h under the summer conditions. Performance parameters were not influenced by dietary treatments. The plasma concentrations of insulin, triiodothyronine, triglyceride, and the ratio of triiodothyronine/thyroxin were decreased and the ratio of glucose/insulin was increased due to transport process. Road transportation also increased the plasma concentrations of protein, cholesterol, aspartate aminotransferase, and creatine kinase and decreased the concentration of low-density lipoprotein cholesterol in the Cr + Vit C group. The pretransport concentrations of insulin and triiodothyronine were highest in the Cr + Vit C group. The concentration of phosphorous was lower in the Cr group than that in the other groups after transport. No significant effects of dietary treatments were observed on the other biochemical parameters. Transport increased malondialdehyde concentration in the control group and did not change plasma total antioxidant capacity and erythrocyte glutathione peroxidase activity. Either in combination or alone, Cr increased plasma total antioxidant capacity (before transport P ≤ 0.05, after transport P = 0.07) but did not affect the concentration of malondialdehyde and activity of glutathione peroxidase. The duration of tonic immobility (TI) was similar between nontransported control chicks and transported chicks without any supplements. Pretreatment with Cr + Vit C significantly reduced the duration of TI.

The impact of individual materials parameters on color temperature reproducibility among phosphor converted LED sources

NASA Astrophysics Data System (ADS)

Schweitzer, Susanne; Nemitz, Wolfgang; Sommer, Christian; Hartmann, Paul; Fulmek, Paul; Nicolics, Johann; Pachler, Peter; Hoschopf, Hans; Schrank, Franz; Langer, Gregor; Wenzl, Franz P.

2014-09-01

For a systematic approach to improve the white light quality of phosphor converted light-emitting diodes (LEDs) for general lighting applications it is imperative to get the individual sources of error for color temperature reproducibility under control. In this regard, it is imperative to understand how compositional, optical and materials properties of the color conversion element (CCE), which typically consists of phosphor particles embedded in a transparent matrix material, affect the constancy of a desired color temperature of a white LED source. In this contribution we use an LED assembly consisting of an LED die mounted on a printed circuit board (PCB) by chip-on-board technology and a CCE with a glob-top configuration as a model system and discuss the impact of potential sources for color temperature deviation among individual devices. Parameters that are investigated include imprecisions in the amount of materials deposition, deviations from the target value for the phosphor concentration in the matrix material, deviations from the target value for the particle sizes of the phosphor material, deviations from the target values for the refractive indexes of phosphor and matrix material as well as deviations from the reflectivity of the substrate surface. From these studies, some general conclusions can be drawn which of these parameters have the largest impact on color deviation and have to be controlled most precisely in a fabrication process in regard of color temperature reproducibility among individual white LED sources.

Treating low carbon/nitrogen (C/N) wastewater in simultaneous nitrification-endogenous denitrification and phosphorous removal (SNDPR) systems by strengthening anaerobic intracellular carbon storage.

PubMed

Wang, Xiaoxia; Wang, Shuying; Xue, Tonglai; Li, Baikun; Dai, Xian; Peng, Yongzhen

2015-06-15

A novel simultaneous nitrification denitrification and phosphorous removal-sequencing batch reactor (SNDPR-SBR) enriched with PAOs (phosphorus accumulating organisms), DPAOs (denitrifying PAOs), and GAOs (glycogen accumulating organisms) at the ratio of 2:1:1 was developed to achieve the simultaneous nutrient and carbon removal treating domestic wastewater with low carbon/nitrogen ratio (≤3.5). The SNDPR system was operated for 120 days at extended anaerobic stage (3 h) and short aerobic stage at low oxygen concentration (2.5 h) with short sludge retention time (SRT) of 10.9 d and hydraulic retention time (HRT) of 14.6 h. The results showed that at the stable operating stage, the average effluent chemical oxygen demand (COD) and PO4(3-)-P concentrations were 47.2 and 0.2 mg L(-1), respectively, the total nitrogen (TN) removal efficiency was 77.7%, and the SND efficiency reached 49.3%. Extended anaerobic stage strengthened the intracellular carbon (mainly poly-β-hydroxybutyrate, PHB) storage, efficiently utilized the organic substances in wastewater, and provided sufficient carbon sources for denitrification and phosphorus uptake without external carbon addition. Short aerobic stage at low oxygen concentration (dissolved oxygen (DO): 1 ± 0.3 mg L(-1)) achieved a concurrence of nitrification, endogenous denitrification, denitrifying and aerobic phosphorus uptake, and saved about 65% energy consumption for aeration. Microbial community analysis demonstrated that P removal was mainly performed by aerobic PAOs while N removal was mainly carried out by denitrifying GAOs (DGAOs), even though DPAOs were also participated in both N and P removal. Copyright © 2015 Elsevier Ltd. All rights reserved.

Process for the removal of acid forming gases from exhaust gases and production of phosphoric acid

DOEpatents

Chang, Shih-Ger; Liu, David K.

1992-01-01

Exhaust gases are treated to remove NO or NO.sub.x and SO.sub.2 by contacting the gases with an aqueous emulsion or suspension of yellow phosphorous preferably in a wet scrubber. The addition of yellow phosphorous in the system induces the production of O.sub.3 which subsequently oxidizes NO to NO.sub.2. The resulting NO.sub.2 dissolves readily and can be reduced to form ammonium ions by dissolved SO.sub.2 under appropriate conditions. In a 20 acfm system, yellow phosphorous is oxidized to yield P.sub.2 O.sub.5 which picks up water to form H.sub.3 PO.sub.4 mists and can be collected as a valuable product. The pressure is not critical, and ambient pressures are used. Hot water temperatures are best, but economics suggest about 50.degree. C. The amount of yellow phosphorus used will vary with the composition of the exhaust gas, less than 3% for small concentrations of NO, and 10% or higher for concentrations above say 1000 ppm. Similarly, the pH will vary with the composition being treated, and it is adjusted with a suitable alkali. For mixtures of NO.sub.x and SO.sub.2, alkalis that are used for flue gas desulfurization are preferred. With this process, better than 90% of SO.sub.2 and NO in simulated flue gas can be removed. Stoichiometric ratios (P/NO) ranging between 0.6 and 1.5 were obtained.

Single-crystal phosphors for high-brightness white LEDs/LDs

NASA Astrophysics Data System (ADS)

Víllora, Encarnación G.; Arjoca, Stelian; Inomata, Daisuke; Shimamura, Kiyoshi

2016-03-01

White light-emitting diodes (wLEDs) are the new environmental friendly sources for general lighting purposes. For applications requiring a high-brightness, current wLEDs present overheating problems, which drastically decrease their emission efficiency, color quality and lifetime. This work gives an overview of the recent investigations on single-crystal phosphors (SCPs), which are proposed as novel alternative to conventional ceramic powder phosphors (CPPs). This totally new approach takes advantage of the superior properties of single-crystals in comparison with ceramic materials. SCPs exhibit an outstanding conversion efficiency and thermal stability up to 300°C. Furthermore, compared with encapsulated CPPs, SCPs possess a superior thermal conductivity, so that generated heat can be released efficiently. The conjunction of all these characteristics results in a low temperature rise of SCPs even under high blue irradiances, where conventional CPPs are overheated or even burned. Therefore, SCPs represent the ideal, long-demanded all-inorganic phosphors for high-brightness white light sources, especially those involving the use of high-density laser-diode beams.

Enhancement of red emission intensity of Ca2Al2SiO7:Eu3+ phosphor by MoO3 doping or excess SiO2 addition for application to white LEDs

NASA Astrophysics Data System (ADS)

Jiao, H. Y.; LiMao, C. R.; Chen, Q.; Wang, P. Y.; Cai, R. C.

2018-01-01

Ca1.86Al2(Si1-xMox)O7:0.14Eu3+ and Ca1.86Al2Si1+yO7+2y:0.14 Eu3+ were synthesized by solid-state reaction. X-ray powder diffraction, excitation and emission spectra were used to investigate their structures and photoluminescence properties. The results shows that the phosphor Ca1.86Al2SiO7:0.14Eu3+ cannot be excited efficiently by light of 393 nm. The introduced Mo ion does not change the position of the excitation peak, but increases both the absorption at 400nm and the emission intensity of Eu3+. The intense red emitting phosphor Ca1.86Al2(Si0.95Mo0.05)O7:0.14Eu3+ was obtained, which has 67% enhanced luminous intensity compared to that of the undoped sample Ca1.86Al2SiO7:0.14Eu3+. Otherwise, SiO2 excess of non-stoichiometric phosphors Ca1.86Al2Si1+yO7+2y:0.14Eu3+ showed the characteristic pattern of a tetragonal structure with a small SiO2 concentration. The optimal phosphor of Ca1.86Al2Si1.1O7.2:0.14Eu3+ has a luminous intensity about two times higher than that of the original stoichiometric phosphor Ca1.86Al2SiO7:0.14Eu3+. We confirmed that the photoluminescence intensity of the obtained phosphors is fairly enhanced by excessive SiO2. The mechanism of this photoluminescence enhancement is discussed in this paper.

Multichannel Luminescence Properties of Mixed-Valent Eu2+/Eu3+ Coactivated SrAl3BO7 Nanocrystalline Phosphors for Near-UV LEDs.

PubMed

Liu, Xiaoming; Xie, Weijie; Lü, Ying; Feng, Jingchun; Tang, Xinghua; Lin, Jun; Dai, Yuhua; Xie, Yu; Yan, Liushui

2017-11-20

Up to now, orchestrating the coexistence of Eu 2+ and Eu 3+ activators in a single host lattice has been an extremely difficult task, especially for the appearance of the characteristic emission of Eu 2+ and Eu 3+ in order to generate white light. Nevertheless, here we demonstrate a new Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphor with abundant and excellent multichannel luminescence properties. A series of Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphors were prepared through a Pechini-type sol-gel method followed by a reduction process. With excitation of UV/NUV light, the prepared SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphors show not only the characteristic f-f transitions of Eu 3+ ion ( 5 D J → 7 F J,J' , J, J' = 0-3), but also the 5d → 4f transitions of Eu 2+ ion with comparable intensity from 400 to 700 nm in the whole visible spectral region. The luminescence color of the SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor can be tuned from blue, blue-green, white, and orange to orange-red by changing the excitation wavelength, the overall doping concentration of europium ions (Eu 2+ , Eu 3+ ), and the relative ratio of Eu 2+ to Eu 3+ ions to some extent. A single-phase white-light emission has been realized in SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor. The obtained SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor has potential application in the area of NUV white-light-emitting diodes.

Potential uranium supply from phosphoric acid: A U.S. analysis comparing solvent extraction and Ion exchange recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Haeyeon; G. Eggert, Roderick; W. Carlsen, Brett

Phosphate rock contains significant amounts of uranium, although in low concentrations. Recovery of uranium as a by-product from phosphoric acid, an intermediate product produced during the recovery of phosphorus from phosphate rock, is not unprecedented. Phosphoric acid plants ceased to produce uranium as a by-product in the early 1990s with the fall of uranium prices. In the last decade, this topic has regained attention due to higher uranium prices and expected increase in demand for uranium. Our study revisits the topic and estimates how much uranium might be recoverable from current phosphoric acid production in the United States and whatmore » the associated costs might be considering two different recovery processes: solvent extraction and ion exchange. Based on U.S. phosphoric acid production in 2014, 5.5 million pounds of U 3O 8 could have been recovered, more than domestic U.S. mine production of uranium in the same year. Annualized costs for a hypothetical uranium recovery plant are US$48-66 per pound U 3O 8 for solvent extraction, the process used historically in the United States to recover uranium from phosphoric acid. For ion exchange, not yet proven at a commercial scale for uranium recovery, the estimated costs are US$33-54 per pound U 3O 8. Our results suggest that it is technically possible for the United States to recover significant quantities of uranium from current phosphoric acid production. And for this type of uranium production to be economically attractive on a large scale, either recovery costs must fall or uranium prices rise.« less

Potential uranium supply from phosphoric acid: A U.S. analysis comparing solvent extraction and Ion exchange recovery

DOE PAGES

Kim, Haeyeon; G. Eggert, Roderick; W. Carlsen, Brett; ...

2016-06-16

Phosphate rock contains significant amounts of uranium, although in low concentrations. Recovery of uranium as a by-product from phosphoric acid, an intermediate product produced during the recovery of phosphorus from phosphate rock, is not unprecedented. Phosphoric acid plants ceased to produce uranium as a by-product in the early 1990s with the fall of uranium prices. In the last decade, this topic has regained attention due to higher uranium prices and expected increase in demand for uranium. Our study revisits the topic and estimates how much uranium might be recoverable from current phosphoric acid production in the United States and whatmore » the associated costs might be considering two different recovery processes: solvent extraction and ion exchange. Based on U.S. phosphoric acid production in 2014, 5.5 million pounds of U 3O 8 could have been recovered, more than domestic U.S. mine production of uranium in the same year. Annualized costs for a hypothetical uranium recovery plant are US$48-66 per pound U 3O 8 for solvent extraction, the process used historically in the United States to recover uranium from phosphoric acid. For ion exchange, not yet proven at a commercial scale for uranium recovery, the estimated costs are US$33-54 per pound U 3O 8. Our results suggest that it is technically possible for the United States to recover significant quantities of uranium from current phosphoric acid production. And for this type of uranium production to be economically attractive on a large scale, either recovery costs must fall or uranium prices rise.« less

Preparation and luminescence properties of Ce3+ and Ce3+/Tb(3+)-activated Y4Si2O7N2 phosphors.

PubMed

Xia, Zhiguo; Wu, Weiwei

2013-09-28

Ce(3+) and Ce(3+)/Tb(3+)-activated Y4Si2O7N2 phosphors are synthesized by the solid-state method, which can be efficiently excited by near ultraviolet (UV) light emitting diode (LED) chips. The PL spectrum of Y4Si2O7N2:Ce(3+) shows a broad hump between 380 and 650 nm, assigned to the electron transition from the 4f energy level to different 5d sub levels of the Ce(3+) ions at different Y(3+) sites. The color of the Y4Si2O7N2:Ce(3+) phosphor can shift from blue to green by introducing Tb(3+). In addition, the energy transfer process from Ce(3+) to Tb(3+) in the Y4Si2O7N2 host was investigated and discussed in terms of both the luminescence spectra and decay curves. The energy transfer critical distance has been calculated and evaluated by the concentration quenching method. Therefore, the Ce(3+) and Ce(3+)/Tb(3+)-activated Y4Si2O7N2 phosphors can serve as key materials for phosphor-converted white-light UV-LEDs.

Blue-green tunable color of Ce3+/Tb3+ coactivated NaBa3La3Si6O20 phosphor via energy transfer

PubMed Central

Jia, Zhen; Xia, Mingjun

2016-01-01

A series of color tunable phosphors NaBa3La3Si6O20:Ce3+, Tb3+ were synthesized via the high-temperature solid-state method. NaBa3La3Si6O20 crystallizes in noncentrosymmetric space group Ama2 with the cell parameters of a = 14.9226(4) Å, b = 24.5215(5) Å and c = 5.6241(2) Å by the Rietveld refinement method. The Ce3+ ions doped NaBa3La3Si6O20 phosphors have a strong absorption band from 260 to 360 nm and show near ultraviolet emission light centered at 378 nm. The Ce3+ and Tb3+ ions coactivated phosphors exhibit color tunable emission light from deep blue to green by adjusting the concentration of the Tb3+ ions. An energy transfer of Ce3+ → Tb3+ investigated by the photoluminescence properties and lifetime decay, is demonstrated to be dipole–quadrupole interaction. These results indicate the NaBa3La3Si6O20:Ce3+, Tb3+ phosphors can be considered as potential candidates for blue-green components for white light emitting diodes. PMID:27628111

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, Bipin Kumar, E-mail: bipinbhu@yahoo.com; Kumar, Arun; Amity Institute of Applied Science, Amity University, Noida, Uttar Pradesh 201303

Herein, a novel green emitting long-persistent Sr{sub 3}SiAl{sub 4}O{sub 11}:Eu{sup 2+}/Dy{sup 3+} phosphor was synthesized in a single phase form using facile solid state reaction method under the reducing atmosphere of 10% H{sub 2} and 90% N{sub 2}. The resulting phosphor exhibits hyper-sensitive strong broad green emission, peaking at 510 nm upon 340 nm excitation wavelength, which is attributed to the 4f{sup 6}5d{sup 1}-4f{sup 7} transitions of emission center of europium (Eu{sup 2+}) ions. Moreover, the incorporation of dysprosium (Dy{sup 3+}) ions, which act as effective hole trap centers with appropriate depth, largely enhances the photoluminescence characteristics and greatly improves the persistentmore » intense luminescence behavior of Sr{sub 3}SiAl{sub 4}O{sub 11}:Eu{sup 2+}/Dy{sup 3+} phosphor under ultraviolet (UV) excitation. In addition, with the optimum doping concentration and sufficient UV excitation time period, the as-synthesized phosphor can be persisted afterglow for time duration ∼4 h with maximum luminescence intensity. Thus, these results suggest that this phosphor could be expected as an ultimate choice for next generation advanced luminescent materials in security applications such as latent finger-marks detection, photo-masking induced phosphorescent images, and security code detection.« less

Ion conduction mechanisms and thermal properties of hydrated and anhydrous phosphoric acids studied with 1H, 2H, and 31P NMR.

PubMed

Aihara, Yuichi; Sonai, Atsuo; Hattori, Mineyuki; Hayamizu, Kikuko

2006-12-14

To understand the behaviors of phosphoric acids in fuel cells, the ion conduction mechanisms of phosphoric acids in condensed states without free water and in a monomer state with water were studied by measuring the ionic conductivity (sigma) using AC impedance, thermal properties, and self-diffusion coefficients (D) and spin-lattice relaxation times (T1) with multinuclear NMR. The self-diffusion coefficient of the protons (H+ or H3O+), H2O, and H located around the phosphate were always larger than the diffusion coefficients of the phosphates and the disparity increased with increasing phosphate concentration. The diffusion coefficients of the samples containing D2O paralleled those in the protonated samples. Since the 1H NMR T1 values exhibited a minimum with temperature, it was possible to determine the correlation times and they were found to be of nanosecond order for a distance of nanometer order for a flip. The agreement of the ionic conductivities measured directly and those calculated from the diffusion coefficients indicates that the ion conduction obeys the Nernst-Einstein equation in the condensed phosphoric acids. The proton diffusion plays a dominant role in the ion conduction, especially in the condensed phosphoric acids.

Dissolved organic carbon concentration controls benthic primary production: results from in situ chambers in north-temperate lakes

USGS Publications Warehouse

Godwin, Sean C.; Jones, Stuart E.; Weidel, Brian C.; Solomon, Christopher T.

2014-01-01

We evaluated several potential drivers of primary production by benthic algae (periphyton) in north-temperate lakes. We used continuous dissolved oxygen measurements from in situ benthic chambers to quantify primary production by periphyton at multiple depths across 11 lakes encompassing a broad range of dissolved organic carbon (DOC) and total phosphorous (TP) concentrations. Light-use efficiency (primary production per unit incident light) was inversely related to average light availability (% of surface light) in 7 of the 11 study lakes, indicating that benthic algal assemblages exhibit photoadaptation, likely through physiological or compositional changes. DOC alone explained 86% of the variability in log-transformed whole-lake benthic production rates. TP was not an important driver of benthic production via its effects on nutrient and light availability. This result is contrary to studies in other systems, but may be common in relatively pristine north-temperate lakes. Our simple empirical model may allow for the prediction of whole-lake benthic primary production from easily obtained measurements of DOC concentration.

Performance of high-recovery recycling reverse osmosis with wash water

NASA Technical Reports Server (NTRS)

Herrmann, Cal C.

1993-01-01

Inclusion of a recycling loop for partially-desalted water from second-stage reverse-osmosis permeate has been shown useful for achieving high-recovery at moderate applied pressures. This approach has now been applied to simulated wash waters, to obtain data on retention by the membranes of solutes in a mixture comparable to anticipated spacecraft hygiene wastewaters, and to generate an estimate of the maximum concentration that can be expected without causing membrane fouling. A first experiment set provides selectivity information from a single membrane and an Igepon detergent, as a function of final concentration. A reject concentration of 3.1% Total Organic Carbon has been reached, at a pressure of 1.4 Mega Pascals, without membrane fouling. Further experiments have generated selectivity values for the recycle configuration from two washwater simulations, as a function of applied pump pressure. Reverse osmosis removal has also been tested for washwater containing detergent formulated for plant growth compatibility (containing nitrogen, phosphorous and potassium functional groups.)

Combined effect of Nitrogen, Phosphorus and Potassium fertilizers on the contents of glucosinolates in rocket salad (Eruca sativa Mill.).

PubMed

Chun, Jin-Hyuk; Kim, Silbia; Arasu, Mariadhas Valan; Al-Dhabi, Naif Abdullah; Chung, Doug Young; Kim, Sun-Ju

2017-02-01

Nitrogen (N), phosphorous (P) and potassium (K) are the most limiting factors in crop production. N often affects the amino acid composition of protein and in turn its nutritional quality. In Brassica plants, abundant supply of N fertilizer decreases the relative proportion of glucosinolates (GSLs), thus reducing the biological and medical values of the vegetables. Hence effort was made to evaluate the influence of different proportions of nutrient solutions containing N-P-K on the GSL profiles of rocket salad ( Eruca sativa Mill.). Fifteen desulpho-(DS) GSLs were isolated and identified using liquid chromatography-mass spectrometry (LC/MS) analysis. Rocket salad plants supplied with lesser amount of N, P or higher concentrations of K showed a typical improvement in total GSL contents. In contrast, total GSL levels were less at higher N supply. Furthermore, with N concentrations above 5 mM and K concentrations less than 2.5 mM, the GSL amounts were on average 13.51 and 13.75 μmol/g dry weight (DW), respectively. Aliphatic GSLs predominated in all concentrations of NPK while indolyl GSLs made up marginally less amount of the total compositions. Five and 2 mM N and P possessed much higher levels of several types of aliphatic GSLs than other concentrations, including glucoerucin, glucoraphanin and dimeric 4-mercaptobutyl GSL. From this perspective, it is contended that supply of less N results in enhancing the metabolic pathway for the synthesis of GSLs in rocket salad.

Photoluminescence properties of a new orange–red emitting Sm{sup 3+}-doped Y{sub 2}Mo{sub 4}O{sub 15} phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Huajuan; Zhao, Ze; Wang, Jing

2015-08-15

A series of novel Y{sub 2}Mo{sub 4}O{sub 15}:xSm{sup 3+} ( (0.01 ≤ x ≤ 0.20) phosphors for white light-emitting (W-LEDs) were successfully prepared by the solid state reaction technology at 973 K for 12 h. X-ray diffraction and photoluminescence spectra were utilized to characterize the structure and luminescence properties of the as-synthesized phosphors. The emission spectra of the Y{sub 2}Mo{sub 4}O{sub 15}:Sm{sup 3+} phosphors consisted of some sharp emission peaks of Sm{sup 3+} ions centered at 565 nm, 605 nm, 650 nm, and 712 nm. The strongest one is located at 605 nm due to {sup 4}G{sub 5/2}–{sup 6}H{sub 7/2}more » transition of Sm{sup 3+}, generating bright orange–red light. The optimum dopant concentration of Sm{sup 3+} ions in Y{sub 2}Mo{sub 4}O{sub 15}:xSm{sup 3+} is around 5 mol% and the critical transfer distance of Sm{sup 3+} is calculated as 23.32 Å. The CIE chromaticity coordinates of the Y{sub 2}Mo{sub 4}O{sub 15}:0.05Sm{sup 3+} phosphors were located in the orange reddish region. The Y{sub 2}Mo{sub 4}O{sub 15}:Sm{sup 3+} phosphors may be potentially used as red phosphors for white light-emitting diodes. - Graphical abstract: The excitation spectrum of Y{sub 2}Mo{sub 4}O{sub 15}:Sm{sup 3+} is composed of a broad band and some sharp f–f transitions. Under 407 nm excitation, the phosphor presents some sharp emission peaks of Sm{sup 3+} ions. - Highlights: • An orange–red emitting Y{sub 2}Mo{sub 4}O{sub 15}:Sm{sup 3+} phosphor has been firstly synthesized. • Their structures, luminescent properties have also been investigated. • The optical absorption edge for the molybdate lies around 325 nm. • The CIE chromaticity coordinates were located in the orange reddish region.« less

Extraction of cellulose nano-crystals from old corrugated container fiber using phosphoric acid and enzymatic hydrolysis followed by sonication.

PubMed

Tang, Yanjun; Shen, Xiaochuang; Zhang, Junhua; Guo, Daliang; Kong, Fangong; Zhang, Nan

2015-07-10

Due to its amazing physicochemical properties and high environmental compatibility, cellulose nano-crystals (CNC) hold great promise for serving as a strategic platform for sustainable development. Now, there has been growing interest in the development of processes using waste or residual biomass as CNC source for addressing economic and environmental concerns. In the present work, a combined process involving phosphoric acid hydrolysis, enzymatic hydrolysis and sonication was proposed aiming to efficiently exact CNC from low-cost old corrugated container (OCC) pulp fiber. The effect of enzymatic hydrolysis on the yield and microstructure of resulting CNC was highlighted. Results showed that the enzymatic hydrolysis was effective in enhancing CNC yield after phosphoric acid hydrolysis. CNC was obtained with a yield of 23.98 wt% via the combined process with phosphoric acid concentration of 60 wt%, cellulase dosage of 2 mL (84 EGU) per 2g fiber and sonication intensity of 200 W. Moreover, the presence of enzymatic hydrolysis imparted the obtained CNC with improved dispersion, increased crystallinity and thermal stability. Copyright © 2015 Elsevier Ltd. All rights reserved.

Energy transfer from Pr3+ to Gd3+ ions in BaB8O13 phosphor for phototherapy lamps

NASA Astrophysics Data System (ADS)

Tamboli, Sumedha; Nair, Govind B.; Dhoble, S. J.; Burghate, D. K.

2018-04-01

A series of BaB8O13 phosphors doped with different concentrations of Gd3+ ions and co-doped with Pr3+ ions were synthesized by solid state synthesis method. X-ray powder diffraction (XRD) analysis confirmed the formation of the compound in a crystalline and homogeneous form. Scanning Electron Microscopy (SEM) was performed to study the surface morphology of the compound and Fourier Transform Infrared (FT-IR) spectroscopy measurements determined the nature of bonding between elements of the compounds. The photoluminescence (PL) excitation spectra of BaB8O13:Gd3+ phosphor showed excitation peaks at 246 nm, 252 nm and 274 nm. The prominent emission peak was observed at 313 nm which is in narrow band ultraviolet B (NB-UVB) range. Energy transfer was achieved by co-doping Pr3+ ions with Gd3+ ions. PL decay time was also measured for BaB8O13: Gd3+, Pr3+ phosphor. Emission at 313 nm can be used for the treatment of skin diseases.

Nutrient composition of plants consumed by black and white ruffed lemurs, Varecia variegata, in the Betampona Natural Reserve, Madagascar.

PubMed

Schmidt, Debra A; Iambana, R Bernard; Britt, Adam; Junge, Randall E; Welch, Charles R; Porton, Ingrid J; Kerley, Monty S

2010-01-01

The purpose of this study was to quantify the concentrations of crude protein, fat, ash, neutral detergent fiber, acid detergent fiber, lignin, nonstructural carbohydrates, and gross energy in plant foods consumed by wild black and white ruffed lemurs (Varecia variegata). Calcium, phosphorous, magnesium, potassium, sodium, iron, zinc, copper, manganese, molybdenum, and selenium concentrations were also determined. A total of 122 samples from 33 plant families and more than 60 species were collected and analyzed for their nutritional content. The specific nutrient needs of black and white ruffed lemurs are unknown, but quantifying the nutritional composition of the foods they consume in the wild will help nutritionists and veterinarians formulate more appropriate diets for captive ruffed lemurs. This information will also supply information on how man-induced habitat changes affect the nutritional composition of foods consumed by free-ranging lemurs. (c) 2009 Wiley-Liss, Inc.

Microwave Synthesis of BCNO/SiO2 Nanocomposite Material

NASA Astrophysics Data System (ADS)

Faryuni, I. D.; Ramdhani, F.; Sampurno, J.; Nuryadin, B. W.; Noor, F. A.; Iskandar, F.

2017-07-01

In the present work, we report the preparation of BCNO/SiO2 phosphor synthesized using a microwave-assisted method. This method allows a lower temperature and a shorter reaction time than simple heating (furnace). The phosphors were prepared from precursors containing, boric acid, urea, citric acid and SiO2 nanoparticles. To These precursors, silica nanoparticles were added at various concentrations from 0 to 5 %wt. The emission wavelength produced by the phosphor was varied by varying the fraction mass of the silica that were added to the precursors. The results showed that higher photoluminescence (PL) intensity was produced by the BCNO/SiO2 with 3 %wt silica addition. The novelty of this research is using microwave heating for BCNO/SiO2 synthesis, which is usually conducted using a simple heating method.

Reductive stripping process for the recovery of uranium from wet-process phosphoric acid

DOEpatents

Hurst, Fred J.; Crouse, David J.

1984-01-01

A reductive stripping flow sheet for recovery of uranium from wet-process phosphoric acid is described. Uranium is stripped from a uranium-loaded organic phase by a redox reaction converting the uranyl to uranous ion. The uranous ion is reoxidized to the uranyl oxidation state to form an aqueous feed solution highly concentrated in uranium. Processing of this feed through a second solvent extraction cycle requires far less stripping reagent as compared to a flow sheet which does not include the reductive stripping reaction.

Near-UV and blue wavelength excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} high efficiency red phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khanna, A.; Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180; Dutta, P.S., E-mail: duttap@rpi.edu

Red phosphors with narrow emission around 615 nm (with FWHM~5–10 nm) having chemical compositions of A{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} (A=Mg, Sr) have been found to exhibit the highest luminescence amongst the molybdate–tungstate family when excited by sources in the 380–420 nm wavelength range. Thus they are most suitable for enhancing color rendering index and lowering color temperature in phosphor converted white LEDs (pc-WLEDs) with near-UV/blue LED excitation sources. The excitation band edge in the near UV/blue wavelength in the reported phosphor has been attributed to the coordination environment of the transition metal ionmore » (Mo{sup 6+}, W{sup 6+}) and host crystal structure. Furthermore the quantum efficiency of the phosphors has been enhanced by adjusting activator concentration, suitable compositional alloying using substitutional alkaline earth metal cations and charge compensation mechanisms. - Graphical abstract: The charge transfer excitation of orthorhombic Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} is significantly higher than tetragonal CaMoO{sub 4}: Eu{sup 3+} phosphors making Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} prime candidates for fabrication of warm white phosphor-converted LEDs. - Highlights: • LED excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} phosphors were synthesized. • These phosphors are 10 times more intense than CaMoO{sub 4}: Eu{sup 3+} red phosphors. • Their intensity and efficiency were enhanced by materials optimization techniques. • Such techniques include compositional alloying, charge compensation, etc.« less

PRO-ACT

EPA Pesticide Factsheets

Technical product bulletin: aka OILCLEAN w/ACTIVATOR, this bioremediation agent (biological additive) used in oil spill cleanups consists of two parts: liquid microbes and activator nutrient.Works best with desired concentrations nitrogen and phosphorous

Optical properties of highly n-doped germanium obtained by in situ doping and laser annealing

NASA Astrophysics Data System (ADS)

Frigerio, J.; Ballabio, A.; Gallacher, K.; Giliberti, V.; Baldassarre, L.; Millar, R.; Milazzo, R.; Maiolo, L.; Minotti, A.; Bottegoni, F.; Biagioni, P.; Paul, D.; Ortolani, M.; Pecora, A.; Napolitani, E.; Isella, G.

2017-11-01

High n-type doping in germanium is essential for many electronic and optoelectronic applications especially for high performance Ohmic contacts, lasing and mid-infrared plasmonics. We report on the combination of in situ doping and excimer laser annealing to improve the activation of phosphorous in germanium. An activated n-doping concentration of 8.8  ×  1019 cm-3 has been achieved starting from an incorporated phosphorous concentration of 1.1  ×  1020 cm-3. Infrared reflectivity data fitted with a multi-layer Drude model indicate good uniformity over a 350 nm thick layer. Photoluminescence demonstrates clear bandgap narrowing and an increased ratio of direct to indirect bandgap emission confirming the high doping densities achieved.

Nickel-Phosphorous Development for Total Solar Irradiance Measurement

NASA Astrophysics Data System (ADS)

Carlesso, F.; Berni, L. A.; Vieira, L. E. A.; Savonov, G. S.; Nishimori, M.; Dal Lago, A.; Miranda, E.

2017-10-01

The development of an absolute radiometer instrument is currently a effort at INPE for TSI measurements. In this work, we describe the development of black Ni-P coatings for TSI radiometers absorptive cavities. We present a study of the surface blackening process and the relationships between morphological structure, chemical composition and coating absorption. Ni-P deposits with different phosphorous content were obtained by electroless techniques on aluminum substrates with a thin zincate layer. Appropriate phosphorus composition and etching parameters process produce low reflectance black coatings.

Facile synthesis of Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} microbelts mat with the enhanced fluorescence and mechanical performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Hailei; Cui, Bo; Wang, Hongzhi, E-mail: wanghz@dhu.edu.cn

2016-01-15

Yellow-emitting phosphor mat consisting of Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} microbelts was prepared by electrospinning and subsequent nitridation. The as-prepared fiber precursor is smooth and uniform with diameter of 800 to 900 nm. After removing organic templates and nitridation, the morphology of the fiber is well retained and thus a smooth microbelts phosphor mat was obtained. X-ray diffraction and the photoluminescence (PL) spectra reveals that a relatively pure Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16} phase and the highest spectral intensity could be obtained at a relatively low temperature of 1500 °C and Eu{sup 2+} doping molar concentration of 0.1. Themore » excitation spectra exhibits a broad band, ranging from 300 to 550 nm, which could be excited by blue LED chip at room temperature. The emission spectra of all exhibits a single broad band in the 400 to 700 nm region, with the maximum intensity always being at 580 nm. The Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} microbelts phosphor mat has the bending strength about 4.5 MPa with a photoluminescence quantum yield as high as 65%. By employing it as yellow phosphor, a high-performance warm white LED could be fabricated with low correlated color temperature (2985 K), high-color-rendering index (Ra=86) and luminous efficacy of 129.5 lm W{sup −1}. Different color temperatures also could be tuned by employing microbelts phosphor mats with different thicknesses. - Graphical abstract: Yellow-emitting phosphor mat consisting of Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} microbelts fibers were prepared by electrospinning the fiber precursor and subsequent nitridation. Because the good mechanical strength it could be utilized to realize LEDs remote packaging. By employing it as yellow phosphor, a high-performance warm white LED could be fabricated. Different color temperatures also could be tuned by employing microbelts phosphor mats with different thicknesses. - Highlights: • Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} microbelts mats were synthesized by electrospinning method. • The optimum doping concentration of Eu{sup 2+} ion is 0.1 mole. • The microbelts mats show strong yellow emission at 580 nm. • The Ca{sub 0.68}Si{sub 9}Al{sub 3}(ON){sub 16}:Eu{sup 2+} mat had the bending strength about 4.5 Mp. • Different color temperatures could be turned with different thicknesses of the mats.« less

Metaheuristics-Assisted Combinatorial Screening of Eu2+-Doped Ca-Sr-Ba-Li-Mg-Al-Si-Ge-N Compositional Space in Search of a Narrow-Band Green Emitting Phosphor and Density Functional Theory Calculations.

PubMed

Lee, Jin-Woong; Singh, Satendra Pal; Kim, Minseuk; Hong, Sung Un; Park, Woon Bae; Sohn, Kee-Sun

2017-08-21

A metaheuristics-based design would be of great help in relieving the enormous experimental burdens faced during the combinatorial screening of a huge, multidimensional search space, while providing the same effect as total enumeration. In order to tackle the high-throughput powder processing complications and to secure practical phosphors, metaheuristics, an elitism-reinforced nondominated sorting genetic algorithm (NSGA-II), was employed in this study. The NSGA-II iteration targeted two objective functions. The first was to search for a higher emission efficacy. The second was to search for narrow-band green color emissions. The NSGA-II iteration finally converged on BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphors in the Eu 2+ -doped Ca-Sr-Ba-Li-Mg-Al-Si-Ge-N compositional search space. The BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphor, which was synthesized with no human intervention via the assistance of NSGA-II, was a clear single phase and gave an acceptable luminescence. The BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphor as well as all other phosphors that appeared during the NSGA-II iterations were examined in detail by employing powder X-ray diffraction-based Rietveld refinement, X-ray absorption near edge structure, density functional theory calculation, and time-resolved photoluminescence. The thermodynamic stability and the band structure plausibility were confirmed, and more importantly a novel approach to the energy transfer analysis was also introduced for BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphors.

Remarkable changes in the photoluminescent properties of Y2Ce2O7:Eu(3+) red phosphors through modification of the cerium oxidation states and oxygen vacancy ordering.

PubMed

Raj, Athira K V; Prabhakar Rao, P; Sreena, T S; Sameera, S; James, Vineetha; Renju, U A

2014-11-21

A new series of red phosphors based on Eu(3+)-doped yttrium cerate [Y1.9Ce2O7:0.1Eu(3+), Y2Ce1.9O7:0.1Eu(3+) and Y2Ce2-xO7:xEu(3+) (x = 0.05, 0.10, 0.15, 0.20, 0.25 and 0.50)] was prepared via a conventional solid-state method. The influence of the substitution of Eu(3+) at the aliovalent site on the photoluminescent properties was determined by powder X-ray diffraction, FT Raman spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, scanning electron microscopy with energy-dispersive spectroscopy, UV-visible absorption spectroscopy, photoluminescence spectroscopy and lifetime measurements. The substitution of Eu(3+) at the Ce(4+) site induces a structural transition from a defect fluorite to a C-type structure, which increases the oxygen vacancy ordering and the distortion of the Eu(3+) environment, and decreases the formation of Ce(3+) states. In contrast, phosphors with isovalent substitution at the Y(3+) site exhibit the biphasic nature of defect fluorite and a C-type structure, thereby increasing the number of Ce(3+) oxidation states. These modifications resulted in remarkable changes in the photoluminescent properties of Y2Ce1.9O7:0.1Eu(3+) red phosphors, with emission intensities 3.8 times greater than those of the Ce0.9O2:0.1Eu(3+) and Y1.9Ce2O7:0.1Eu(3+). The photoluminescent properties of Y2Ce2-xO7:xEu(3+) were studied at different Eu(3+) concentrations under excitation with blue light. These phosphors emit intense red light due to the (5)D0-(7)F2 transition under excitation at 466 nm and no concentration quenching is observed with up to 50 mol% Eu(3+). They show increased lifetimes in the range 0.62-0.72 ms at Eu(3+) concentrations. The cation ordering linked to the oxygen vacancy ordering led to the uniform distribution of Eu(3+) ions in the lattice, thus allowing higher doping concentrations without quenching and consequently increasing the lifetime of the (5)D0 states. Our results demonstrate that significant improvements in the photoluminescence properties can be achieved by the structural alteration of a fluorite CeO2 to a C-type lattice.

A novel blue-greenish emitting phosphor Ba{sub 3}LaK(PO{sub 4}){sub 3}F:Tb{sup 3+} with high thermal stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Chao; Huang, Hongwei, E-mail: hhw@cugb.edu.cn; Hu, Yingmo, E-mail: huyingmo@cugb.edu.cn

Highlights: • The Ba{sub 3}LaK(PO{sub 4}){sub 3}F:Tb{sup 3+} phosphors exhibit a broad excitation band. • The Ba{sub 3}LaK(PO{sub 4}){sub 3}F:Tb{sup 3+} emission color adjust from blue to green. • The Ba{sub 3}LaK(PO{sub 4}){sub 3}F:Tb{sup 3+} show superior thermal stability. - Abstract: Ba{sub 3}La{sub 1−m}K(PO{sub 4}){sub 3}F:mTb{sup 3+}(m = 0.01–0.50) phosphors have been prepared by a traditional high temperature solid-state reaction. XRD analysis verified the apatite-type phase structure of the as-prepared samples, and the morphology has been checked by the Scanning electron microscope (SEM). The emission spectrum of Ba{sub 3}LaK(PO{sub 4}){sub 3}F:Tb{sup 3+} phosphor consists of two regions, blue emission bandmore » from 380 to 470 nm and green emission band from 470 to 650 nm. With increasing Tb{sup 3+} ions doped concentration (m), the color hue of Ba{sub 3}La{sub 1−m}K(PO{sub 4}){sub 3}F:mTb{sup 3+}adjusts from blue to green. On the basis of concentration quenching method, the critical distance between Tb{sup 3+} ions is calculated to be 7.98 Å, suggesting that multipolar interaction predominate in quenching process. In addition, the temperature-dependence PL spectra of Ba{sub 3}LaK(PO{sub 4}){sub 3}F:0.01Tb{sup 3+} and Ba{sub 3}LaK(PO{sub 4}){sub 3}F:0.40Tb{sup 3+} phosphor are given,which exhibit superior thermal stability.« less

Tune color of single-phase LiGd(MoO4)2-X(WO4)X: Sm3+, Tb3+ via adjusting the proportion of matrix and energy transfer to create white-light phosphor

NASA Astrophysics Data System (ADS)

Wu, Hongyue; Yang, Junfeng; Wang, Xiaoxue; Gan, Shucai; Li, Linlin

2018-03-01

A series of LiGd(MO4)2: Sm3+, Tb3+ (M = Mo, W) phosphors was prepared by a conventional solid state reaction method. Powder X-Ray diffraction (XRD) analysis reveals that the compounds are of the same structure type. Their luminescent properties have been studied. The optimal doping concentrations are 8% for Sm3+ and 18% for Tb3+ in the LiGd(MoO4)2 host. Sm3+ and Tb3+ have different sensitivity to the Mo/W ratio. For LiGd(MoO4)2-X(WO4)X: Sm3+ (X = 0, 0.4, 0.8, 1.2, 1.6, 2.0), the strongest emission intensity is 1.766 times than that of the weakest, while 171 times for LiGd(MoO4)2-X(WO4)X: Tb3+. The experimental results show that Mo/W ratio strong influences on the properties of LiGd(MoO4)2-X(WO4)X: Tb3+. With the increasing of WO42- groups concentration, the shape of characteristic excitation peaks of Tb3+ is almost the same and the excitation intensity gradually increase. Moreover, the energy transfer from Tb3+ to Sm3+ has been realized in the co-doped phosphors. The experimental analysis and theoretical calculations reveal that the quadrupole-quadrupole interaction is the dominant mechanism for the Tb3+→Sm3+ energy transfer. Therefore, luminous intensity can be adjusted by different sensitivities to matrix composition and energy transfer from Tb3+→Sm3+. By this tuning color method, white-light-emitting phosphor has been prepared. The excitation wavelength is 378 nm, and this indicates that the white-light-emitting phosphor could be pumped by near-UV light.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Yue; College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600; Chen, Baojiu, E-mail: chenmbj@sohu.com

Tb{sup 3+}, Eu{sup 3+} codoped YF{sub 3} nano- and micro-crystals with the morphologies of ellipsoid-like nanoplate, spindle, sandwich-structural rhombus and nanoaggregate were synthesized through a solvothermal method. The morphologies of the prepared products can be tailored by controlling the volume ratio of ethylene glycol (EG) to H{sub 2}O, solvent type or the reaction time. A possible formation mechanism of the sandwich-structural rhombus like YF{sub 3} phosphor was proposed. The emitting colors of YF{sub 3}:Tb{sup 3+},Eu{sup 3+} phosphors can be easily tuned from yellowish green, yellow to orange by increasing Eu{sup 3+} concentration. The energy transfer from Tb{sup 3+} to Eu{supmore » 3+} in YF{sub 3} phosphors was studied. It was found that the interaction type between Tb{sup 3+} and Eu{sup 3+} is electric dipole-dipole interaction. - Graphical abstract: Sandwich-structural rhombus like YF{sub 3}:Tb{sup 3+}, Eu{sup 3+} phosphors were synthesized through a solvothermal process. The formation mechanism of the sandwich-structural rhombus like YF{sub 3}:Tb{sup 3+}, Eu{sup 3+} phosphors was studied. Highlights: Black-Right-Pointing-Pointer YF{sub 3} nano- and micro-crystals were synthesized through solvothermal route. Black-Right-Pointing-Pointer A formation mechanism of the sandwich-structural rhombus like YF{sub 3} was proposed. Black-Right-Pointing-Pointer The emitting colors of YF{sub 3}:Tb{sup 3+},Eu{sup 3+} phosphors can be tuned. Black-Right-Pointing-Pointer Energy transfer from Tb{sup 3+} to Eu{sup 3+} is confirmed as electric dipole-dipole interaction.« less

Crystal structure and Temperature-Dependent Luminescence Characteristics of KMg4(PO4)3:Eu2+ phosphor for White Light-emitting diodes

PubMed Central

Chen, Jian; Liu, Yangai; Mei, Lefu; Liu, Haikun; Fang, Minghao; Huang, Zhaohui

2015-01-01

The KMg4(PO4)3:Eu2+ phosphor was prepared by the conventional high temperature solid-state reaction. The crystal structure, luminescence and reflectance spectra, thermal stability, quantum efficiency and the application for N-UV LED were studied respectively. The phase formation and crystal structure of KMg4(PO4)3:Eu2+ were confirmed from the powder X-ray diffraction and the Rietveld refinement. The concentration quenching of Eu2+ in the KMg4(PO4)3 host was determined to be 1mol% and the quenching mechanism was certified to be the dipole–dipole interaction. The energy transfer critical distance of as-prepared phosphor was calculated to be about 35.84Å. Furthermore, the phosphor exhibited good thermal stability and the corresponding activation energy ΔE was reckoned to be 0.24eV. Upon excitation at 365nm, the internal quantum efficiency of the optimized KMg4(PO4)3:Eu2+ was estimated to be 50.44%. The white N-UV LEDs was fabricated via KMg4(PO4)3:Eu2+, green-emitting (Ba,Sr)2SiO4:Eu2+, and red-emitting CaAlSiN3:Eu2+ phosphors with a near-UV chip. The excellent color rendering index (Ra = 96) at a correlated color temperature (5227.08K) with CIE coordinates of x = 0.34, y = 0.35 of the WLED device indicates that KMg4(PO4)3:Eu2+ is a promising blue-emitting phosphor for white N-UV light emitting diodes (LEDs). PMID:25855866

Crystal structure and temperature-dependent luminescence characteristics of KMg4(PO4)3:Eu(2+) phosphor for white light-emitting diodes.

PubMed

Chen, Jian; Liu, Yangai; Mei, Lefu; Liu, Haikun; Fang, Minghao; Huang, Zhaohui

2015-04-09

The KMg4(PO4)3:Eu(2+) phosphor was prepared by the conventional high temperature solid-state reaction. The crystal structure, luminescence and reflectance spectra, thermal stability, quantum efficiency and the application for N-UV LED were studied respectively. The phase formation and crystal structure of KMg4(PO4)3:Eu(2+) were confirmed from the powder X-ray diffraction and the Rietveld refinement. The concentration quenching of Eu(2+) in the KMg4(PO4)3 host was determined to be 1 mol% and the quenching mechanism was certified to be the dipole-dipole interaction. The energy transfer critical distance of as-prepared phosphor was calculated to be about 35.84 Å. Furthermore, the phosphor exhibited good thermal stability and the corresponding activation energy ΔE was reckoned to be 0.24 eV. Upon excitation at 365 nm, the internal quantum efficiency of the optimized KMg4(PO4)3:Eu(2+) was estimated to be 50.44%. The white N-UV LEDs was fabricated via KMg4(PO4)3:Eu(2+), green-emitting (Ba,Sr)2SiO4:Eu(2+), and red-emitting CaAlSiN3:Eu(2+) phosphors with a near-UV chip. The excellent color rendering index (Ra = 96) at a correlated color temperature (5227.08 K) with CIE coordinates of x = 0.34, y = 0.35 of the WLED device indicates that KMg4(PO4)3:Eu(2+) is a promising blue-emitting phosphor for white N-UV light emitting diodes (LEDs).

Photovoltaic Performance Enhancement of Silicon Solar Cells Based on Combined Ratios of Three Species of Europium-Doped Phosphors

PubMed Central

You, Bang-Jin; Liu, Jheng-Jie; Bai, Wen-Bin; Syu, Hong-Jhang; Lin, Ching-Fuh

2018-01-01

This paper presents a scheme for the enhancement of silicon solar cells in terms of luminescent emission band and photovoltaic performance. The proposed devices are coated with an luminescent down-shifting (LDS) layer comprising three species of europium (Eu)-doped phosphors mixed within a silicate film (SiO2) using a spin-on film deposition. The three species of phosphor were mixed at ratios of 0.5:1:1.5, 1:1:1, or 1.5:1:0.5 in weight percentage (wt %). The total quantity of Eu-doped phosphors in the silicate solution was fixed at 3 wt %. The emission wavelengths of the Eu-doped phosphors were as follows: 518 nm (specie-A), 551 nm (specie-B), and 609 nm (specie-C). We examined the extended luminescent emission bands via photoluminescence measurements at room temperature. Closely matching the luminescent emission band to the high responsivity band of the silicon semiconductor resulted in good photovoltaic performance. Impressive improvements in efficiency were observed in all three samples: 0.5:1:1.5 (20.43%), 1:1:1 (19.67%), 1.5:1:0.5 (16.81%), compared to the control with a layer of pure SiO2 (13.80%). PMID:29783716

Luminescent properties of Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} and its potential application in white light emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhijun, E-mail: wangzhijunmail@yahoo.com.cn; Li, Panlai; Li, Ting

2013-06-01

Graphical abstract: Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} phosphor can be effectively excited by an ultraviolet and near-ultraviolet light, and produce a bright blue emission centered at 436 nm. The CIE chromaticity coordinations (x, y) of Na{sub 2}CaSiO{sub 4}:Eu{sup 2+}(NSCE)/Li{sub 2}SrSiO{sub 4}:Eu{sup 2+}(LSSE) vary with the molar ratio of the two constituents. When NSCE/LSSE is 1:3, the CIE chromaticity coordination is (0.332, 0.346), which is close to that of the natural sunlight (0.33, 0.33). The results indicate that Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} may be a promising blue phosphor for UV chip-based multi-phosphor converted white light emitting diodes. Highlights: ► Na{sub 2}CaSiO{sub 4}:Eu{supmore » 2+} shows the blue emission with a peak at 436 nm and broad excitation band in the UV/n-UV range. ► White light with CIE coordinates (0.332, 0.346) is generated by mixing the blue phosphor with the Li{sub 2}SrSiO{sub 4}:Eu{sup 2+} yellow phosphor. ► Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} would be a promising blue phosphor candidate for UV chip-based multi-phosphor converted white LEDs. - Abstract: A novel blue phosphor Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} is synthesized by a high temperature solid-state reaction, and its luminescent properties are systematically studied. Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} can be effectively excited by the 354 nm radiation, and create blue emission (436 nm). The emission intensity of Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} is influenced by the Eu{sup 2+} doping content, and the optimal doping content is 1.5%, and the concentration quenching mechanism of Eu{sup 2+} in Na{sub 2}CaSiO{sub 4} can be attributed to the multipolar interaction. The white light with CIE coordinates (0.332, 0.346) is generated by mixing the blue phosphor Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} with the yellow phosphor Li{sub 2}SrSiO{sub 4}:Eu{sup 2+}. The results indicate that Na{sub 2}CaSiO{sub 4}:Eu{sup 2+} may be a potential blue emitting phosphor for UV chip-based multi-phosphor converted white light emitting diodes.« less

Impact of a moderate/high-severity prescribed eucalypt forest fire on soil phosphorous stocks and partitioning.

PubMed

Santín, Cristina; Otero, Xose L; Doerr, Stefan H; Chafer, Chris J

2018-04-15

This study examines the direct impact of a moderate/high-severity prescribed fire on phosphorous (P) stocks and partitioning in oligotrophic soils of a dry eucalypt forest within Sydney's water supply catchments, Australia. We also quantify and characterize the P present in the ash produced in this fire, and explore its relationships with the maximum temperatures recorded in the litter layer during the burn. In these oligotrophic soils, P concentrations were already relatively low before the fire (<130mgkg -1 , mainly in organic forms). The fire consumed the entire litter layer and the thin Oa soil horizon, creating 6.3±3.1tha -1 of ash, and resulted into direct net P losses of ~7kgha -1 . The P lost was mostly organic and there was a moderate net gain of inorganic and non-reactive P forms. Importantly, only a small proportion of the post-fire P was bioavailable (equivalent to ~3% of the total P lost during fire). Higher total P concentrations in ash corresponded with higher maximum temperatures (>650°C) recorded in the burning litter layer, but effects of fire temperature on ash P partitioning were not significant. Fire not only transformed P chemically, but also physically. Our results show that, immediately after fire, up to 2kgha -1 of P was present in the ash layer and, therefore, highly erodible and susceptible to be transported off-site by wind- and water erosion. Even if most of this P was, initially, of low bioavailability, its transfer to depositional environments with different geochemical conditions (e.g. anoxic sediments in water reservoirs) can alter its geochemical forms and availability. Further investigation of potential P transformations off-site is therefore essential, particularly given that SE-Australian water supply catchments are subject to recurrent perturbation by prescribed fire and wildfires. The latter have already resulted in major algal blooms in water supply reservoirs. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of acid etching and adhesive treatments on host-derived cysteine cathepsin activity in dentin.

PubMed

Zhang, Wenhao; Yang, Weixiang; Wu, Shuyi; Zheng, Kaibin; Liao, Weili; Chen, Boli; Yao, Ke; Liang, Guobin; Li, Yan

2014-10-01

To analyze the effects of different processes during bonding on endogenous cysteine cathepsin activity in dentin. Dentin powder, prepared from extracted human third molars, was divided into 10 groups. Two lots of dentin powder were used to detect the effects of the procedure of protein extraction on endogenous cathepsin activity. The others were used to study effects of different acid-etching or adhesive treatments on enzyme activity. Concentrations of 37% phosphoric acid or 10% phosphoric acid, two etch-and-rinse adhesive systems, and two self-etching adhesive systems were used as dentin powder treatments. The untreated mineralized dentin powder was set as the control. After treatment, the proteins of each group were extracted. The total cathepsin activity in the extracts of each group was monitored with a fluorescence reader. In the control group, there were no significant differences in cathepsin activity between the protein extract before EDTA treatment and the protein extract after EDTA treatment (p > 0.05). The cathepsin activities of the three different extracts in the 37% phosphoric acid-treated group were different from each other (p < 0.05). The two acid-etching groups and two etch-and-rinse groups showed significant enzyme activity reduction vs the control group (p < 0.05). There were no significant differences between those four groups (p > 0.05). Treating the dentin powder with any of the two self-etching adhesives resulted in an increase in cathepsin activity (p < 0.05). The activity of cysteine cathepsins can be detected in dentin powder. Treatment with EDTA during protein extraction exerted an influence on cathepsin activity. Acid etching or etch-and-rinse adhesive systems may reduce the activity of endogenous cathepsins in dentin. Self-etching adhesive systems may increase the enzyme activity.

Synthesis, structure, and photoluminescence properties of novel KBaSc2 (PO4 )3 :Ce(3+) /Eu(2+) /Tb(3+) phosphors for white-light-emitting diodes.

PubMed

Jiao, Mengmeng; Lü, Wei; Shao, Baiqi; Zhao, Lingfei; You, Hongpeng

2015-08-24

A series of novel KBaSc2 (PO4 )3 :Ce(3+) /Eu(2+) /Tb(3+) phosphors are prepared using a solid-state reaction. X-ray diffraction analysis and Rietveld structure refinement are used to check the phase purity and crystal structure of the prepared samples. Ce(3+) - and Eu(2+) -doped phosphors both have broad excitation and emission bands, owing to the spin- and orbital-allowed electron transition between the 4f and 5d energy levels. By co-doping the KBaSc2 (PO4 )3 :Eu(2+) and KBaSc2 (PO4 )3 :Ce(3+) phosphors with Tb(3+) ions, tunable colors from blue to green can be obtained. The critical distance between the Eu(2+) and Tb(3+) ions is calculated by a concentration quenching method and the energy-transfer mechanism for Eu(2+) →Tb(3+) is studied by utilizing the Inokuti-Hirayama model. In addition, the quantum efficiencies of the prepared samples are measured. The results indicate that KBaSc2 (PO4 )3 :Eu(2+) ,Tb(3+) and KBaSc2 (PO4 )3 :Ce(3+) ,Tb(3+) phosphors might have potential applications in UV-excited white-light-emitting diodes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Molten-salt synthesis and composition-dependent luminescent properties of barium tungsto-molybdate-based solid solution phosphors

NASA Astrophysics Data System (ADS)

Xiang-Hong, He; Zhao-Lian, Ye; Ming-Yun, Guan; Ning, Lian; Jian-Hua, Sun

2016-02-01

Pr3+-activated barium tungsto-molybdate solid solution phosphor Ba(Mo1-zWz)O4:Pr3+ is successfully fabricated via a facile molten-salt approach. The as-synthesized microcrystal is of truncated octahedron and exhibits deep-red-emitting upon blue light excitation. Powder x-ray diffraction and Raman spectroscopy techniques are utilized to investigate the formation of solid solution phosphor. The luminescence behaviors depend on the resulting composition of the microcrystals with fixed Pr3+-doping concentration, while the host lattices remain in a scheelite structure. The forming solid solution via the substitution of [WO4] for [MoO4] can significantly enhance its luminescence, which may be due to the fact that Ba(Mo1-zWz)O4:Pr3+ owns well-defined facets and uniform morphologies. Owing to its properties of high phase purity, well-defined facets, highly uniform morphologies, exceptional chemical and thermal stabilities, and stronger emission intensity, the resulting solid solution phosphor is expected to find potential applications in phosphor-converted white light-emitting diodes (LEDs). Project supported by the Construction Fund for Science and Technology Innovation Group from Jiangsu University of Technology, China, the Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, China (Grant No. KHK1409), the Priority Academic Program Development of Jiangsu Higher Education Institutions, China, and the National Natural Science Foundation of China (Grant No. 21373103).

3D fabrication and characterization of phosphoric acid scaffold with a HA/β-TCP weight ratio of 60:40 for bone tissue engineering applications.

PubMed

Wang, Yanen; Wang, Kai; Li, Xinpei; Wei, Qinghua; Chai, Weihong; Wang, Shuzhi; Che, Yu; Lu, Tingli; Zhang, Bo

2017-01-01

A key requirement for three-dimensional printing (3-DP) at room temperature of medical implants depends on the availability of printable and biocompatible binder-powder systems. Different concentration polyvinyl alcohol (PVA) and phosphoric acid solutions were chosen as the binders to make the artificial stent biocompatible with sufficient compressive strength. In order to achieve an optimum balance between the bioceramic powder and binder solution, the biocompatibility and mechanical properties of these artificial stent samples were tested using two kinds of binder solutions. This study demonstrated the printable binder formulation at room temperature for the 3D artificial bone scaffolds. 0.6 wt% PVA solution was ejected easily via inkjet printing, with a supplementation of 0.25 wt% Tween 80 to reduce the surface tension of the polyvinyl alcohol solution. Compared with the polyvinyl alcohol scaffolds, the phosphoric acid scaffolds had better mechanical properties. Though both scaffolds supported the cell proliferation, the absorbance of the polyvinyl alcohol scaffolds was higher than that of the phosphoric acid scaffolds. The artificial stents with a hydroxyapatite/beta-tricalcium phosphate (HA/β-TCP) weight ratios of 60:40 depicted good biocompatibility for both scaffolds. Considering the scaffolds' mechanical and biocompatible properties, the phosphoric acid scaffolds with a HA/β-TCP weight ratio of 60:40 may be the best combination for bone tissue engineering applications.

The development of Ce3+-activated (Gd,Lu)3Al5O12 garnet solid solutions as efficient yellow-emitting phosphors

NASA Astrophysics Data System (ADS)

Li, Jinkai; Li, Ji-Guang; Liu, Shaohong; Li, Xiaodong; Sun, Xudong; Sakka, Yoshio

2013-10-01

Ce3+-activated Gd3Al5O12 garnet, effectively stabilized by Lu3+ doping, has been developed for new yellow-emitting phosphors. The powder processing of [(Gd1-xLux)1-yCey]3Al5O12 solid solutions was achieved through precursor synthesis via carbonate precipitation, followed by annealing. The resultant (Gd,Lu)AG:Ce3+ phosphor particles exhibit typical yellow emission at ˜570 nm (5d-4f transition of Ce3+) upon blue-light excitation at ˜457 nm (the 2F5/2-5d transition of Ce3+). The quenching concentration of Ce3+ was determined to be ˜1.0 at% (y = 0.01) and the quenching mechanism was suggested to be driven by exchange interactions. The best luminescent [(Gd0.9Lu0.1)0.99Ce0.01]AG phosphor is comparative to the well-known YAG:Ce3+ in emission intensity but has a substantially red-shifted emission band that is desired for warm-white lighting. The effects of processing temperature (1000-1500 °C) on the spectroscopic properties of the phosphors, especially those of Lu3+/Ce3+, were thoroughly investigated and discussed from the centroid position and crystal field splitting of the Ce3+ 5d energy levels.

Antimicrobial efficiency of ethanol and 2-propanol alcohols used on contaminated storage phosphor plates and impact on durability of the plate

PubMed Central

Wenzel, A; Kornum, F; Knudsen, MR; Lau, E Frandsen

2013-01-01

Objectives: To assess (1) antimicrobial efficiency of wiping intraoral phosphor plates with alcohol tissues based on ethanol or 2-propanol alcohols after contamination with Candida albicans and Streptococcus oralis, (2) a concept for autodisinfection with ultraviolet light of the transport ramp in a scanner for phosphor plates and (3) the impact of wiping with alcohol tissues on durability of the plate. Methods: Suspensions of C. albicans and S. oralis were prepared in concentrations of 109 and 105 organisms per ml, and Digora (Digora® Optime Imaging Plate, size 2; Soredex, PalaDEx Group Brenntag Nordic A/S, Hellerup, Denmark) and Vista (VistaScan® Imaging Plate PLUS, size 2; Dürr Dental AG, Bietigheim-Bissingen, Germany) plates were contaminated. The plates were wiped with ethanol or 2-propanol disinfectant tissues and imprints obtained on agar. Number of microbial colonies after culturing was recorded. The scanner ramp was contaminated with C. albicans or S. oralis, respectively, the ultraviolet light (UV light) disinfection in the scanner was activated and the number of colonies after culturing was recorded. Plates from each system were sequentially wiped (5–60 times) with ethanol and 2-propanol, exposed and scanned. 48 images from each system were scored blind: 1 = no artefact, 2 = small artefacts and 3 = severe artefacts. Results: Ethanol eliminated C. albicans and S. oralis in high and low concentrations from both types of plates, whereas 2-propanol did not eliminate all micro-organisms at high concentrations. The UV light eliminated all micro-organisms from the ramp. Ethanol degraded the plates to a larger extent than did 2-propanol. Images from Vista plates showed severe artefacts after wiping with ethanol; those from Digora plates did not. Conclusions: Ethanol eliminated all micro-organisms but degraded phosphor plates, whereas 2-propanol did not eliminate all micro-organisms and still degraded plates from Vista but not from Digora. PMID:23420856

Antimicrobial efficiency of ethanol and 2-propanol alcohols used on contaminated storage phosphor plates and impact on durability of the plate.

PubMed

Wenzel, A; Kornum, F; Knudsen, Mr; Lau, E Frandsen

2013-01-01

To assess (1) antimicrobial efficiency of wiping intraoral phosphor plates with alcohol tissues based on ethanol or 2-propanol alcohols after contamination with Candida albicans and Streptococcus oralis, (2) a concept for autodisinfection with ultraviolet light of the transport ramp in a scanner for phosphor plates and (3) the impact of wiping with alcohol tissues on durability of the plate. Suspensions of C. albicans and S. oralis were prepared in concentrations of 10(9) and 10(5) organisms per ml, and Digora (Digora(®) Optime Imaging Plate, size 2; Soredex, PalaDEx Group Brenntag Nordic A/S, Hellerup, Denmark) and Vista (VistaScan(®) Imaging Plate PLUS, size 2; Dürr Dental AG, Bietigheim-Bissingen, Germany) plates were contaminated. The plates were wiped with ethanol or 2-propanol disinfectant tissues and imprints obtained on agar. Number of microbial colonies after culturing was recorded. The scanner ramp was contaminated with C. albicans or S. oralis, respectively, the ultraviolet light (UV light) disinfection in the scanner was activated and the number of colonies after culturing was recorded. Plates from each system were sequentially wiped (5-60 times) with ethanol and 2-propanol, exposed and scanned. 48 images from each system were scored blind: 1 = no artefact, 2 = small artefacts and 3 = severe artefacts. Ethanol eliminated C. albicans and S. oralis in high and low concentrations from both types of plates, whereas 2-propanol did not eliminate all micro-organisms at high concentrations. The UV light eliminated all micro-organisms from the ramp. Ethanol degraded the plates to a larger extent than did 2-propanol. Images from Vista plates showed severe artefacts after wiping with ethanol; those from Digora plates did not. Ethanol eliminated all micro-organisms but degraded phosphor plates, whereas 2-propanol did not eliminate all micro-organisms and still degraded plates from Vista but not from Digora.

Removal of phosphorus-rich phase from high-phosphorous iron ore by melt separation at 1573 K in a super-gravity field

NASA Astrophysics Data System (ADS)

Gao, Jin-tao; Guo, Lei; Zhong, Yi-wei; Ren, Hong-ru; Guo, Zhan-cheng

2016-07-01

A new approach of removing the phosphorus-rich phase from high-phosphorous iron ore by melt separation at 1573 K in a super- gravity field was investigated. The iron-slag separation by super-gravity resulted in phosphorus being effectively removed from the iron-rich phase and concentrated as a phosphorus-rich phase at a temperature below the melting point of iron. The samples obtained by super-gravity exhibited obvious layered structures. All the iron grains concentrated at the bottom of the sample along the super-gravity direction, whereas the molten slag concentrated in the upper part of the sample along the opposite direction. Meanwhile, fine apatite crystals collided and grew into larger crystals and concentrated at the slag-iron interface. Consequently, in the case of centrifugation with a gravity coefficient of G = 900, the mass fractions of the slag phase and iron-rich phase were similar to their respective theoretical values. The mass fraction of MFe in the iron-rich phase was as high as 97.77wt% and that of P was decreased to 0.092wt%.

Microsphere morphology tuning and photo-luminescence properties of monoclinic Y2WO6

NASA Astrophysics Data System (ADS)

Gao, Hong; Bai, Yulong; Zhang, Junying; Tang, Zilong

2015-04-01

Effects of the solution pH value and reaction time on the precursor morphology and photoluminescence properties are investigated for hydrothermally prepared monoclinic Y2WO6 phosphors. In the near-neutral environment, sodium dodecyl benzene sulfonate (SDBS) surfactant forms small microspheres micelles as template to synthesize microspherical precursor. H+ ions concentration affects the arrangement of negative ionic surfactant SDBS. As a result, jujube-liked and popcorn-like loose microspheres formed at low pH value. When the pH value is 5.2 and the hydrothermal reaction time reaches 24 h, respectively, the strongest luminescent intensity can be obtained. Under this condition, the precursor presented regular microsphere with diameter of 4.0 μm. After high-temperature heat treatment, the obtained phosphor particles still exhibit microsphere-like shape. Therefore, we provide an effective method to tune the morphology of Y2WO6 phosphors and study the relationship between morphology and luminescent performance.

Research on optical biosensor with up-converting phosphor marker

NASA Astrophysics Data System (ADS)

Zhao, Yongkai; Zhou, Lei; Wang, Jing; Huang, Lihua; Yan, Zhongqiang; Huang, Huijie; Yang, Ruifu; Liu, Lei; Ren, Bingqiang; Wang, Xiangzhao

2006-08-01

An optical biosensor with up-converting phosphor (UCP) marker is developed for the sensitive rapid immunoassay to the specific biomolecule. UCP can emit visible light when excited by infrared light. Through detecting and analyzing the content of UCP particles on the test strip after immunoreaction, the concentration of target analyte in the sample can be obtained. The detection sensitivity to plague IgG is better than 5 ng/ml; to plague FI-Ab is better than 100 pg/ml; to plague Yersinia pestis cell is better than 3*10^(4) CFU/ml. Good linear response characteristics and an excellent correlation (R2>=0.95) have been verified by quantitative detection results. In the practical application, detection results to 167 analytic samples have an excellent consistency with those obtained by reverse hemagglutination test. The up-converting phosphor technology (UPT) based biosensor has stable, reliable, and sensitive performances. It can meet the need of various bioassay applications.

Performance of vegetated swales for improving road runoff quality in a moderate traffic urban area.

PubMed

Leroy, Marie-Charlotte; Portet-Koltalo, Florence; Legras, Marc; Lederf, Franck; Moncond'huy, Vincent; Polaert, Isabelle; Marcotte, Stéphane

2016-10-01

In recent years, due to their economic and ecological advantages, green infrastructures for stormwater management have been widely implemented. The present study focused on vegetated swales and compared two vegetated covers, grassed or planted with macrophytes in order to evaluate their performance in terms of water quality improvement. These swales collected runoff of a moderately busy road (<2500vehday(-1)) in a commercial area. Twelve storm events were analyzed over a two year period with measurement of total suspended solids (TSS), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total hydrocarbons (THC), total phosphorous (TP), total Kjeldahl nitrogen (TKN), trace elements and 16 polycyclic aromatic hydrocarbons (PAHs). The grass cover led to poor results due to lower retention of soil particles on which trace elements and PAHs are bounded. The swales planted with macrophytes, with a deeper root system more capable of retaining soil particles, led to reductions of concentrations from 17 to 45% for trace elements such as lead, zinc and copper and 30% for the 16 PAHs in infiltrated waters. In addition, the macrophyte cover showed lower variability of pollutant concentrations in infiltrated waters compared to incoming waters. This buffering capacity is interesting to mitigate the impact of moderate peak pollution on surface water or ground water quality. Copyright © 2016 Elsevier B.V. All rights reserved.

Estimation of phosphorus flux in rivers during flooding.

PubMed

Chen, Yen-Chang; Liu, Jih-Hung; Kuo, Jan-Tai; Lin, Cheng-Fang

2013-07-01

Reservoirs in Taiwan are inundated with nutrients that result in algal growth, and thus also reservoir eutrophication. Controlling the phosphorus load has always been the most crucial issue for maintaining reservoir water quality. Numerous agricultural activities, especially the production of tea in riparian areas, are conducted in watersheds in Taiwan. Nutrients from such activities, including phosphorus, are typically flushed into rivers during flooding, when over 90% of the yearly total amount of phosphorous enters reservoirs. Excessive or enhanced soil erosion from rainstorms can dramatically increase the river sediment load and the amount of particulate phosphorus flushed into rivers. When flow rates are high, particulate phosphorus is the dominant form of phosphorus, but sediment and discharge measurements are difficult during flooding, which makes estimating phosphorus flux in rivers difficult. This study determines total amounts of phosphorus transport by measuring flood discharge and phosphorous levels during flooding. Changes in particulate phosphorus, dissolved phosphorus, and their adsorption behavior during a 24-h period are analyzed owing to the fact that the time for particulate phosphorus adsorption and desorption approaching equilibrium is about 16 h. Erosion of the reservoir watershed was caused by adsorption and desorption of suspended solids in the river, a process which can be summarily described using the Lagmuir isotherm. A method for estimating the phosphorus flux in the Daiyujay Creek during Typhoon Bilis in 2006 is presented in this study. Both sediment and phosphorus are affected by the drastic discharge during flooding. Water quality data were collected during two flood events, flood in June 9, 2006 and Typhoon Bilis, to show the concentrations of suspended solids and total phosphorus during floods are much higher than normal stages. Therefore, the drastic changes of total phosphorus, particulate phosphorus, and dissolved phosphorus in rivers during flooding should be monitored to evaluate the loading of phosphorus more precisely. The results show that monitoring and controlling phosphorus transport during flooding can help prevent the eutrophication of a reservoir.

[Effect of phosphor on accumulation and chemical forms of cadmium, and physiological characterization in different varieties of Capsicum annuum L].

PubMed

Zhang, Xiao-Jing; Liu, Ji-Zhen; Xu, Wei-Hong; Chen, Gui-Qing; Wang, Hui-Xian; Zhang, Hai-Bo; Han, Gui-Qi; Zeng, Hong-Jun; Lan, Chun-Tao; Xiong, Zhi-Ting; Wei, Song-Qing

2011-04-01

Pot experiments were carried out to investigate the influence of different Phosphor (P) levels (0, 0.3% and 0.5%) on the plant growth, activities of antioxidant enzymes, accumulation and chemical forms of cadmium (Cd) in Capsicum annuum L. when exposed to Cd (10 mg x kg(-1)). The results showed that dry weights of leaf, fruit, roots and total dry weights of plant, and concentration and accumulation of Cd significantly differed between two varieties of Capsicum annuum L. Dry weights of fruit and total plant of Chaotianjiao increased by P (0.3% and 0.5%), while that of Yanjiao425 was inhibited. Activities of catalase (CAT) were increased at first, and then reduced in the presence of P; Activities of superoxide dismutase (SOD) and peroxidase (POD) of Chaotianjiao increased with increasing levels of P, but activities of SOD and POD of Yanjiao425 decreased with increasing levels of P. Chemical forms of Cd in fruit of Capsicum annuum L. were in order of F(NaCl) > F(HAC) > F(E) > Fr > F(HC) > F(W). The total extractable Cd, ethanol-extractable Cd, hydrochloric acid-extractable Cd and residual Cd in fruit of Ynajiao425 obviously decreased in the presence of P compared to the control, while the total extractable Cd, water-extractable Cd, acetic acid-extractable Cd and residual Cd in fruit of Chaotianjiao increased. Cadmium accumulations of Capsicum annuum L. were in order of roots > stew > leaf > fruit. Cadmium accumulations in fruit and plant of Yanjiao425 were decreased by 47.7% and 58.5% , 5.5% and 13. 1% in the presence of 0.3% and 0.5% P when exposed to Cd, and Cd accumulations in fruit and plant of Chaotianjiao were decreased by 23.6% in the presence of 0.3% P.

Nitrification denitrification enhanced biological phosphorous removal (NDEBPR) occurs in a lab-scale alternating hypoxic/oxic membrane bioreactor.

PubMed

Sibag, Mark; Kim, Han-Seung

2012-01-01

Strict anaerobic or anoxic maintenance of the system and process susceptibility to low organic loading are major concerns in nitrification denitrification enhanced biological phosphorous removal (NDEBPR). The study has initiated NDEBPR in a lab-scale alternating hypoxic/oxic membrane bioreactor by developing an enhanced mixed microbial culture capable of removing 97±2% COD, 99±0.84% NH(3)-N, 90±3% TN, and 96±1% TP-PO(4)(3-) with 20-day SRT. The viable cells ranging from 1.6×10(8) to 2.0×10(8)cells/ml estimated from the total bacterial genomic DNA (6.43-7.83 μg DNA/ml) represented only 5% of the MLVSS indicating low microbial biomass concentration. Reducing the organic load from 1250 to 750 mg COD/ml as glucose did not deteriorate the effluent quality (3.77±1.0 mg N-TN/l; 0.08±0.24 mg NH(3)-N/l; and 0.32±0.10 mg PO(4)(3-)-P/l). These observations are characteristics of activated sludge that harbors denitrifying polyphosphate accumulating organisms (DPAOs). The results showed that NDEBPR can be achieved under alternating hypoxic/oxic conditions. Copyright © 2011 Elsevier Ltd. All rights reserved.

Novel yellow-emitting Sr8MgLn(PO4)7:Eu2+ (Ln=Y, La) phosphors for applications in white LEDs with excellent color rendering index.

PubMed

Huang, Chien-Hao; Chen, Teng-Ming

2011-06-20

Eu(2+)-activated Sr(8)MgY(PO(4))(7) and Sr(8)MgLa(PO(4))(7) yellow-emitting phosphors were successfully synthesized by solid-state reactions for applications in excellent color rendering index white light-emitting diodes (LEDs). The excitation and reflectance spectra of these phosphors show broad band excitation and absorption in the 250-450 nm near-ultraviolet region, which is ascribed to the 4f(7) → 4f(6)5d(1) transitions of Eu(2+). Therefore, these phosphors meet the application requirements for near-UV LED chips. Upon excitation at 400 nm, the Sr(8)MgY(PO(4))(7):Eu(2+) and Sr(8)MgLa(PO(4))(7):Eu(2+) phosphors exhibit strong yellow emissions centered at 518, 610, and 611 nm with better thermal stability than (Ba,Sr)(2)SiO(4) (570 nm) commodity phosphors. The composition-optimized concentrations of Eu(2+) in Sr(8)MgLa(PO(4))(7):Eu(2+) and Sr(8)MgY(PO(4))(7):Eu(2+) phosphors were determined to be 0.01 and 0.03 mol, respectively. A warm white-light near-UV LED was fabricated using a near-UV 400 nm chip pumped by a phosphor blend of blue-emitting BaMgAl(10)O(17):Eu(2+) and yellow-emitting Sr(8)MgY(PO(4))(7):0.01Eu(2+) or Sr(8)MgLa(PO(4))(7):0.03Eu(2+), driven by a 350 mA current. The Sr(8)MgY(PO(4))(7):0.01Eu(2+) and Sr(8)MgLa(PO(4))(7):0.03Eu(2+) containing LEDs produced a white light with Commission International de I'Eclairage (CIE) chromaticity coordinates of (0.348, 0.357) and (0.365, 0.328), warm correlated color temperatures of 4705 and 4100 K, and excellent color rendering indices of 95.375 and 91.75, respectively. © 2011 American Chemical Society

Highly Regular, Uniform K3ScF6:Mn4+ Phosphors: Facile Synthesis, Microstructures, Photoluminescence Properties, and Application in Light-Emitting Diode Devices.

PubMed

Ming, Hong; Liu, Shuifu; Liu, Lili; Peng, Jiaqing; Fu, Junxiang; Du, Fu; Ye, Xinyu

2018-06-13

A new generation of red phosphors of complex fluoride matrices activated with Mn 4+ has gained a broad interest in getting high color quality and low color temperature of solid-state white light-emitting diodes (WLEDs). However, besides their instability toward moisture, the extremely irregular and nonuniform morphologies of these phosphors have limited their practical industry applications. In the present study, a novel type of K 3 ScF 6 :Mn 4+ red phosphor with highly regular, uniform, and high color purity was obtained successfully through a facile coprecipitation route under mild conditions. The crystal structure was identified with aids of the powder X-ray diffraction, Rietveld refinement, and density functional theory calculations. The prototype crystallizes in the space group Fm3 m with a cubic structure, and the lattice parameters are fitted well to be a = b = c = 8.4859(8) Å and V = 611.074(2) Å 3 . The Mn 4+ ions occupy Sc 3+ sites and locate at the centers of the distorted ScF 6 octahedrons. A wide band gap of approximately 6.15 eV can provide sufficient space to accommodate impurity energy levels. Unlike most other Mn 4+ ion-activated fluoride phosphors, the as-prepared K 3 ScF 6 :Mn 4+ phosphors demonstrate highly uniform and regular morphologies with shapes transforming from cube to octahedron with increasing Mn 4+ ion concentration. Under blue light excitation, the as-prepared K 3 ScF 6 :Mn 4+ sample exhibits intense sharp-line red fluorescence (the strongest peak located at 631 nm) with high color purity. An excellent recovery in luminescence upon heating and cooling processes implies high stability of K 3 ScF 6 :Mn 4+ . Furthermore, a warm WLED fabricated with blue GaN chips merged with the mixture of K 3 ScF 6 :Mn 4+ and the well-known commercial YAG:Ce 3+ yellow phosphors exhibits wonderful color quality with lower correlated color temperature (3250 K) and higher color-rendering index ( R a = 86.4). These results suggest that the K 3 ScF 6 :Mn 4+ phosphor possesses stupendous potentiality for practical applications.

Health impairments arising from drinking water polluted with domestic sewage and excreta in China.

PubMed

Ling, B

2000-01-01

Raw water of poor quality still causes many drinking-water associated health problems all over China, largely because of poor sanitation, inadequate disposal of sewage and excreta. Eutrophication due to excess of total nitrogen and phosphorous in some sources for drinking-water has led to massive proliferation of cyanobacteria. The dominant species of cyanophyta can produce microcystins, a potent liver cancer promotor. As in previous studies, high incidence of liver cancer coincided with high microcystin concentration in the source water, especially in pond water. A frequent consequence of heavy pollution of source water is further the high incidence of infectious intestinal diseases, which are more than 10-100 times as frequent in China than in developed countries.

Effect of Silica Nanoparticles on the Photoluminescence Properties of BCNO Phosphor

NASA Astrophysics Data System (ADS)

Nuryadin, Bebeh W.; Faryuni, Irfana Diah; Iskandar, Ferry; Abdullah, Mikrajuddin; Khairurrijal, Khairurrijal

2011-12-01

Effect of additional silica nanoparticles on the photoluminescence (PL) performance of boron carbon oxy-nitride (BCNO) phosphor was investigated. As a precursor, boric acid and urea were used as boron and nitrogen sources, respectively. The carbon sources was polyethylene glycol (PEG) with average molecule weight 20000 g/mol.. Precursor solutions were prepared by mixing these raw materials in pure water, followed by stirring to achieve homogeneous solutions. In this precursor, silica nanoparticles were added at various mass ratio from 0 to 7 %wt in the solution. The precursors were then heated at 750 °C for 60 min in a ceramic crucible under atmospheric pressure. The photoluminescence (PL) spectrum that characterized by spectrophotometer showed a single, distinct, and broad emission band varied from blue to near red color, depend on the PEG, boric acid and urea ratio in the precursor. The addition of silica nanoparticles caused the increasing of PL intensity as well as the shifting of peak wavelength of PL spectrum. The peak shifting of PL was affected by the concentration of silica nanoparticles that added into the precursor. We believe that the BCNO-silica composite phosphor becomes a promising material for the phosphor conversion-based white light-emitting diodes.

Color tunable emission in Ce3+ and Tb3+ co-doped Ba2Ln(BO3)2Cl (Ln=Gd and Y) phosphors for white light-emitting diodes.

PubMed

Zhang, Niumiao; Guo, Chongfeng; Jing, Heng; Jeong, Jung Hyun

2013-12-01

Ce(3+) and Tb(3+) co-doped Ba2Ln(BO3)2Cl (Ln=Y and Gd) green emitting phosphors were prepared by solid state reaction in reductive atmosphere. The emission and excitation spectra as well as luminescence decays were investigated, showing the occurrence of efficient energy transfer from Ce(3+) to Tb(3+) in this system. The phosphors exhibit both a blue emission from Ce(3+) and a green emission from Tb(3+) under near ultraviolet light excitation with 325-375 nm wavelength. Emission colors of phosphors could be tuned from deep blue through cyan to green by adjusting the Tb(3+) concentrations. The energy transfer efficiency and emission intensity of Ba2Y(BO3)2Cl:Ce(3+), Tb(3+) precede those of Ba2Gd(BO3)2Cl:Ce(3+), Tb(3+), and the sample Ba2Y(BO3)2Cl:0.03Ce(3+), 0.10Tb(3+) is the best candidate for n-UV LEDs. Copyright © 2013 Elsevier B.V. All rights reserved.

Triple energy transfer and color tuning in Tb3+ and Eu3+-coactivated apatite-type gadolinium-containing phosphors

NASA Astrophysics Data System (ADS)

Guo, Ning; Liang, Qimeng; Li, Shuo; Ouyang, Ruizhuo; Lü, Wei

2017-11-01

A family of apatite-type fluorophosphate phosphors with general formula Sr3Gd(1-m-n)Na(PO4)3F:mTb3+,nEu3+ (SGN:mTb3+,nEu3+) have been synthesized via the high-temperature solid-state reaction method. Triple energy transfer processes from Gd3+ in the host to both Tb3+ and Eu3+, as well as from Tb3+ to Eu3+ have been verified by the photoluminescence spectra. Under the excitation of UV light, both green line from the transitions of Tb3+ and red line origin from the transitions of Eu3+ have been simultaneously observed in a single phase phosphor, which makes a promise for tunable color emissions from yellowish-green through yellow and ultimately to reddish-orange by simply adjusting the Eu3+ content (n) in SGN:0.20Tb3+,nEu3+ phosphors. Additionally, the energy transfer from the Tb3+ to the Eu3+ ions has been demonstrated to be a resonant type via a quadrupole-quadrupole mechanism based on the Dexter's theoretical model, and the energy transfer efficiency increases with an increase in Eu3+ concentration.

Luminescence Properties of Ca19Ce(PO4)14:A (A = Eu3+/Tb3+/Mn2+) Phosphors with Abundant Colors: Abnormal Coexistence of Ce4+/3+-Eu3+ and Energy Transfer of Ce3+ → Tb3+/Mn2+ and Tb3+-Mn2.

PubMed

Shang, Mengmeng; Liang, Sisi; Lian, Hongzhou; Lin, Jun

2017-06-05

A series of Eu 3+ /Tb 3+ /Mn 2+ -ion-doped Ca 19 Ce(PO 4 ) 14 (CCPO) phosphors have been prepared via the conventional high-temperature solid-state reaction process. Under UV radiation, the CCPO host presents a broad blue emission band from Ce 3+ ions, which are generated during the preparation process because of the formation of deficiency. The Eu 3+ -doped CCPO phosphors can exhibit magenta to red-orange emission as a result of the abnormal coexistence of Ce 3+ /Ce 4+ /Eu 3+ and the metal-metal charge-transfer (MMCT) effect between Ce 3+ and Eu 3+ . When Tb 3+ /Mn 2+ are doped into the hosts, the samples excited with 300 nm UV light present multicolor emissions due to energy transfer (ET) from the host (Ce 3+ ) to the activators with increasing activator concentrations. The emitting colors of CCPO:Tb 3+ phosphors can be tuned from blue to green, and the CCPO:Mn 2+ phosphors can emit red light. The ET mechanism from the host (Ce 3+ ) to Tb 3+ /Mn 2+ is demonstrated to be a dipole-quadrapole interaction for Ce 3+ → Tb 3+ and an exchange interaction for Ce 3+ → Mn 2+ in CCPO:Tb 3+ /Mn 2+ . Abundant emission colors containing white emission were obtained in the Tb 3+ - and Mn 2+ -codoped CCPO phosphors through control of the levels of doped Tb 3+ and Mn 2+ ions. The white-emitted CCPO:Tb 3+ /Mn 2+ phosphor exhibited excellent thermal stability. The photoluminescence properties have shown that these materials might have potential for UV-pumped white-light-emitting diodes.

A single-phase white light emitting Pr3+ doped Ba2CaWO6 phosphor: synthesis, photoluminescence and optical properties

NASA Astrophysics Data System (ADS)

Sreeja, E.; Vidyadharan, Viji; Jose, Saritha K.; George, Anns; Joseph, Cyriac; Unnikrishnan, N. V.; Biju, P. R.

2018-04-01

Pr3+ doped Ba2CaWO6 phosphor were prepared by traditional high-temperature solid-state reaction technique. The structure evolution was systematically investigated by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. The X-ray powder diffraction patterns indicate that the prepared phosphors crystallized in the cubic double-perovskite structure. The functional groups were identified using FTIR spectra and the elements present in the composition were confirmed by the EDS profile. The morphology of the phosphor was identified using SEM and TEM analysis. The PL spectra illustrated that these phosphors could be efficiently excited by charge transfer band of host and the maximum luminescence intensity was observed at 0.06 wt% of Pr3+ ion. Upon the charge transfer band excitation, emission spectra showed peaks at 489, 532, 647, 685 and 737 nm corresponding to 3P0→3H4, 3P1→3H5, 3P0→3F2, 3P0→3F3 and 3P0→3F4 transitions respectively. The concentration quenching of Ba2CaWO6:Pr3+ phosphor can be mainly attributed to dipole-dipole interaction. The CIE coordinates were estimated to be close to the white region. The decay curves are well fitted with double exponential decay models. The standard and modified Judd-Ofelt (JO) theories were used to determine the Judd-Ofelt intensity parameters, radiative transition probabilities and branching ratios. The optical properties indicate that Ba2CaWO6:Pr3+ phosphors can produce white light emission from a single phase host and its potential application for solid-state lighting and display devices.

Effect of phosphoric acid pretreatment of corncobs on the fermentability of Clostridium beijerinckii TISTR 1461 for biobutanol production.

PubMed

Boonsombuti, Akarin; Luengnaruemitchai, Apanee; Wongkasemjit, Sujitra

2015-01-01

Corncobs pretreated with H2SO4, HNO3, and H3PO4 were compared to evaluate the fermentation ability of Clostridium beijerinckii TISTR 1461 to produce biobutanol via acetone-butanol-ethanol (ABE) fermentation. It was found that the hydrolysate from H3PO4 pretreatment could be used as a substrate without any inhibitor removal methods. However, in terms of sugar yield, it gave the lowest total sugars in both pretreatment and enzymatic hydrolysis. Response surface methodology was applied to optimize enzymatic hydrolysis of the pretreated corncobs. The optimized conditions reduced the consumption of enzymes and hydrolysis time to 7.68 FPU/g biomass and 63.88 hr, respectively, and yielded 51.82 g/L reducing sugars. The Celluclast 1.5 L and Novozyme 188 enzyme ratio were varied to maximize the hydrolyzed sugars. The ABE fermentation, using substrate from phosphoric acid pretreatment of corncobs, with 10 g/L glucose supplementation produced 11.64 g/L of total ABE, which was close to the control experiment using synthetic medium. This study showed that corncobs pretreated with phosphoric acid could potentially be used as a substrate without using a detoxification process.

Photoluminescence properties and energy transfer in Ce(3+) /Dy(3+) co-doped Sr(3) MgSi(2) O(8) phosphors for potential application in ultraviolet white light-emitting diodes.

PubMed

Yu, Hong; Zi, Wenwen; Lan, Shi; Gan, Shucai; Zou, Haifeng; Xu, Xuechun; Hong, Guangyan

2013-01-01

Sr(3) MgSi(2) O(8) :Ce(3+) , Dy(3+) phosphors were prepared by a solid-state reaction technique and the photoluminescence properties were investigated. The emission spectra show not only a band due to Ce(3+) ions (403 nm) but also as a band due to Dy(3+) ions (480, 575 nm) (UV light excitation). The photoluminescence properties reveal that effective energy transfer occurs in Ce(3+) /Dy(3+) co-doped Sr(3) MgSi(2) O(8)phosphors, and the co-doping of Ce(3+) could enhance the emission intensity of Dy(3+) to a certain extent by transferring its energy to Dy(3+) . The Ce(3+) /Dy(3+) energy transfer was investigated by emission/excitation spectra, and photoluminescence decay behaviors. In Sr2.94 MgSi2 O8 :0.01Ce(3+) , 0.05Dy(3+) phosphors, the fluorescence lifetime of Dy(3+) (from 3.35 to 27.59 ns) is increased whereas that of Ce(3+) is greatly decreased (from 43.59 to 13.55 ns), and this provides indirect evidence of the Ce(3+) to Dy(3+) energy transfer. The varied emitted color of Sr(3) MgSi(2) O(8):Ce(3+) , Dy(3+) phosphors from blue to white were achieved by altering the concentration ratio of Ce(3+) and Dy(3+) . These results indicate Sr(3) MgSi(2) O(8):Ce(3+) , Dy(3+) may be as a candidate phosphor for white light-emitting diodes. Copyright © 2012 John Wiley & Sons, Ltd.

Temperature dependent luminescence and energy transfer properties of Na2SrMg(PO4)2:Eu2+, Mn2+ phosphors.

PubMed

Geng, Dongling; Shang, Mengmeng; Zhang, Yang; Lian, Hongzhou; Lin, Jun

2013-11-21

Eu(2+) singly and Eu(2+)/Mn(2+) co-doped Na2SrMg(PO4)2 (NSMP) phosphors have been prepared via a high-temperature solid-state reaction process. Upon UV excitation of 260-360 nm, the NSMP:xEu(2+) phosphors exhibit a violet band located at 399 nm and a blue band centered at 445 nm, which originate from Eu(2+) ions occupying two different crystallographic sites: Eu(2+)(I) and Eu(2+)(II), respectively. Excitation wavelengths longer than 380 nm can selectively excite Eu(2+)(II) to emit blue light. Energy transfer processes in the Eu(2+)(I)-Eu(2+)(II) and Eu(2+)-Mn(2+) pairs have been observed and investigated by luminescence spectra and decay curves. The emission color of as-prepared samples can be tuned by changing the relative concentrations of Eu(2+) and Mn(2+) ions and adjusting the excitation wavelength. Under UV excitation of 323 nm, the absolute quantum yield of NSMP:0.005Eu(2+) is 91%, which is higher than most of the other Eu(2+)-doped phosphors reported previously. The temperature dependent luminescence properties and decay curves (4.3-450 K) of NSMP:Eu(2+) and NSMP:Eu(2+), Mn(2+) phosphors have been studied in detail. Thermal quenching of Eu(2+) has been observed while the emission band of Mn(2+) shows a blue-shift and an abnormal increase of intensity with increasing temperature. The unusual thermal quenching behavior indicates that the NSMP compound can serve as a good lattice host for Mn(2+) ions which can be used as a red-emitting phosphor. Additionally, the lifetimes for Eu(2+)(I) and Eu(2+)(II) increase with increasing temperatures.

Cell surface acid-base properties of Escherichia coli and Bacillus brevis and variation as a function of growth phase, nitrogen source and C:N ratio.

PubMed

Hong, Yongsuk; Brown, Derick G

2006-07-01

Potentiometric titration has been conducted to systematically examine the acid-base properties of the cell surfaces of Escherichia coli K-12 and Bacillus brevis as a function of growth phase, nitrogen source (ammonium or nitrate), and carbon to nitrogen (C:N) ratio of the growth substrate. The two bacterial species revealed four distinct proton binding sites, with pK(a) values in the range of 3.08-4.05 (pK(1)), 4.62-5.57 (pK(2)), 6.47-7.30 (pK(3)), and 9.68-10.89 (pK(4)) corresponding to phosphoric/carboxylic, carboxylic, phosphoric, and hydroxyl/amine groups, respectively. Two general observations in the data are that for B. brevis the first site concentration (N(1)), corresponding to phosphoric/carboxylic groups (pK(1)), varied as a function of nitrogen source, while for E. coli the fourth site concentration (N(4)), corresponding to hydroxyl/amine groups (pK(4)), varied as a function of C:N ratio. Correspondingly, it was found that N(1) was the highest of the four site concentrations for B. brevis and N(4) was the highest for E. coli. The concentrations of the remaining sites showed little variation. Finally, comparison between the titration data and a number of cell surface compositional studies in the literature indicates one distinct difference between the two bacteria is that pK(4) of the Gram-negative E. coli can be attributed to hydroxyl groups while that of the Gram-positive B. brevis can be attributed to amine groups.

Arctic foxes as ecosystem engineers: increased soil nutrients lead to increased plant productivity on fox dens

NASA Astrophysics Data System (ADS)

Gharajehdaghipour, Tazarve; Roth, James D.; Fafard, Paul M.; Markham, John H.

2016-04-01

Top predators can provide fundamental ecosystem services such as nutrient cycling, and their impact can be even greater in environments with low nutrients and productivity, such as Arctic tundra. We estimated the effects of Arctic fox (Vulpes lagopus) denning on soil nutrient dynamics and vegetation production near Churchill, Manitoba in June and August 2014. Soils from fox dens contained higher nutrient levels in June (71% more inorganic nitrogen, 1195% more extractable phosphorous) and in August (242% more inorganic nitrogen, 191% more extractable phosphorous) than adjacent control sites. Inorganic nitrogen levels decreased from June to August on both dens and controls, whereas extractable phosphorous increased. Pup production the previous year, which should enhance nutrient deposition (from urine, feces, and decomposing prey), did not affect soil nutrient concentrations, suggesting the impact of Arctic foxes persists >1 year. Dens supported 2.8 times greater vegetation biomass in August, but δ15N values in sea lyme grass (Leymus mollis) were unaffected by denning. By concentrating nutrients on dens Arctic foxes enhance nutrient cycling as an ecosystem service and thus engineer Arctic ecosystems on local scales. The enhanced productivity in patches on the landscape could subsequently affect plant diversity and the dispersion of herbivores on the tundra.

Arctic foxes as ecosystem engineers: increased soil nutrients lead to increased plant productivity on fox dens.

PubMed

Gharajehdaghipour, Tazarve; Roth, James D; Fafard, Paul M; Markham, John H

2016-04-05

Top predators can provide fundamental ecosystem services such as nutrient cycling, and their impact can be even greater in environments with low nutrients and productivity, such as Arctic tundra. We estimated the effects of Arctic fox (Vulpes lagopus) denning on soil nutrient dynamics and vegetation production near Churchill, Manitoba in June and August 2014. Soils from fox dens contained higher nutrient levels in June (71% more inorganic nitrogen, 1195% more extractable phosphorous) and in August (242% more inorganic nitrogen, 191% more extractable phosphorous) than adjacent control sites. Inorganic nitrogen levels decreased from June to August on both dens and controls, whereas extractable phosphorous increased. Pup production the previous year, which should enhance nutrient deposition (from urine, feces, and decomposing prey), did not affect soil nutrient concentrations, suggesting the impact of Arctic foxes persists >1 year. Dens supported 2.8 times greater vegetation biomass in August, but δ(15)N values in sea lyme grass (Leymus mollis) were unaffected by denning. By concentrating nutrients on dens Arctic foxes enhance nutrient cycling as an ecosystem service and thus engineer Arctic ecosystems on local scales. The enhanced productivity in patches on the landscape could subsequently affect plant diversity and the dispersion of herbivores on the tundra.

Optimization of cellulose nanocrystal length and surface charge density through phosphoric acid hydrolysis

NASA Astrophysics Data System (ADS)

Vanderfleet, Oriana M.; Osorio, Daniel A.; Cranston, Emily D.

2017-12-01

Cellulose nanocrystals (CNCs) are emerging nanomaterials with a large range of potential applications. CNCs are typically produced through acid hydrolysis with sulfuric acid; however, phosphoric acid has the advantage of generating CNCs with higher thermal stability. This paper presents a design of experiments approach to optimize the hydrolysis of CNCs from cotton with phosphoric acid. Hydrolysis time, temperature and acid concentration were varied across nine experiments and a linear least-squares regression analysis was applied to understand the effects of these parameters on CNC properties. In all but one case, rod-shaped nanoparticles with a high degree of crystallinity and thermal stability were produced. A statistical model was generated to predict CNC length, and trends in phosphate content and zeta potential were elucidated. The CNC length could be tuned over a relatively large range (238-475 nm) and the polydispersity could be narrowed most effectively by increasing the hydrolysis temperature and acid concentration. The CNC phosphate content was most affected by hydrolysis temperature and time; however, the charge density and colloidal stability were considered low compared with sulfuric acid hydrolysed CNCs. This study provides insight into weak acid hydrolysis and proposes `design rules' for CNCs with improved size uniformity and charge density. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

Arctic foxes as ecosystem engineers: increased soil nutrients lead to increased plant productivity on fox dens

PubMed Central

Gharajehdaghipour, Tazarve; Roth, James D.; Fafard, Paul M.; Markham, John H.

2016-01-01

Top predators can provide fundamental ecosystem services such as nutrient cycling, and their impact can be even greater in environments with low nutrients and productivity, such as Arctic tundra. We estimated the effects of Arctic fox (Vulpes lagopus) denning on soil nutrient dynamics and vegetation production near Churchill, Manitoba in June and August 2014. Soils from fox dens contained higher nutrient levels in June (71% more inorganic nitrogen, 1195% more extractable phosphorous) and in August (242% more inorganic nitrogen, 191% more extractable phosphorous) than adjacent control sites. Inorganic nitrogen levels decreased from June to August on both dens and controls, whereas extractable phosphorous increased. Pup production the previous year, which should enhance nutrient deposition (from urine, feces, and decomposing prey), did not affect soil nutrient concentrations, suggesting the impact of Arctic foxes persists >1 year. Dens supported 2.8 times greater vegetation biomass in August, but δ15N values in sea lyme grass (Leymus mollis) were unaffected by denning. By concentrating nutrients on dens Arctic foxes enhance nutrient cycling as an ecosystem service and thus engineer Arctic ecosystems on local scales. The enhanced productivity in patches on the landscape could subsequently affect plant diversity and the dispersion of herbivores on the tundra. PMID:27045973

All-in-one light-tunable borated phosphors with chemical and luminescence dynamical control resolution.

PubMed

Lin, Chun Che; Liu, Yun-Ping; Xiao, Zhi Ren; Wang, Yin-Kuo; Cheng, Bing-Ming; Liu, Ru-Shi

2014-06-25

Single-composition white-emitting phosphors with superior intrinsic properties upon excitation by ultraviolet light-emitting diodes are important constituents of next-generation light sources. Borate-based phosphors, such as NaSrBO3:Ce(3+) and NaCaBO3:Ce(3+), have stronger absorptions in the near-ultraviolet region as well as better chemical/physical stability than oxides. Energy transfer effects from sensitizer to activator caused by rare-earth ions are mainly found in the obtained photoluminescence spectra and lifetime. The interactive mechanisms of multiple dopants are ambiguous in most cases. We adjust the doping concentration in NaSrBO3:RE (RE = Ce(3+), Tb(3+), Mn(2+)) to study the energy transfer effects of Ce(3+) to Tb(3+) and Mn(2+) by comparing the experimental data and theoretical calculation. The vacuum-ultraviolet experimental determination of the electronic energy levels for Ce(3+) and Tb(3+) in the borate host regarding the 4f-5d and 4f-4f configurations are described. Evaluation of the Ce(3+)/Mn(2+) intensity ratios as a function of Mn(2+) concentration is based on the analysis of the luminescence dynamical process and fluorescence lifetime measurements. The results closely agree with those directly obtained from the emission spectra. Density functional calculations are performed using the generalized gradient approximation plus an on-site Coulombic interaction correction scheme to investigate the forbidden mechanism of interatomic energy transfer between the NaSrBO3:Ce(3+) and NaSrBO3:Eu(2+) systems. Results indicate that the NaSrBO3:Ce(3+), Tb(3+), and Mn(2+) phosphors can be used as a novel white-emitting component of UV radiation-excited devices.

Photoluminescence properties of Tb3Al5O12:Ce3+ garnet synthesized by the metal organic decomposition method

NASA Astrophysics Data System (ADS)

Onishi, Yuya; Nakamura, Toshihiro; Adachi, Sadao

2017-02-01

Tb3Al5O12:Ce3+ garnet (TAG:Ce3+) phosphor was synthesized by the metal organic decomposition (MOD) method and subsequent calcination at Tc = 800-1200°C for 1 h in air. The effects of Ce3+ concentration on the phosphor properties were investigated in detail using X-ray diffraction (XRD) analysis, photoluminescence (PL) analysis, PL excitation (PLE) spectroscopy, and PL decay measurements. The maximum intensity in the Ce3+ yellow emission was observed at the Ce3+ concentration of ∼0.20%. PLE and PL decay measurements suggested an evidence of the energy transfer from Tb3+ to Ce3+. Calcination temperature dependence of the XRD and PL intensities yielded an energy of ∼1.5 eV both for the TAG formation in the MOD process and for the optical activation of Ce3+ in its lattice sites. Temperature dependences of the PL intensity for the TAG:Ce3+ yellow-emitting and K2SiF6:Mn4+ red-emitting phosphors were also examined for the future solid-state lighting applications at T = 20-500 K in 10-K steps. The data of TAG:Ce3+ were analyzed using a theoretical model with considering a reservoir level of Et ∼9 meV, yielding a quenching energy of Eq ∼0.35 eV, whereas the K2SiF6:Mn4+ red-emitting phosphor data yielded a value of Eq ∼1.0 eV. The schematic energy-level diagrams for Tb3+ and Ce3+ were proposed for the sake of a better understanding of these ions in the TAG host.

Synthesis and characterization of Mg2SiO4:Tb3+, Eu3+ phosphors for white light generation

NASA Astrophysics Data System (ADS)

Cho, Shinho

2016-09-01

The effect of Eu3+ codoping on the structural, morphological, and optical properties of Mg2SiO4:Tb3+ was investigated. The phosphor powders were synthesized by changing the molar concentration of Eu3+ at a fixed Tb3+ content of 5 mol% by using a conventional solid-state reaction. The X-ray diffraction patterns revealed that the crystal structure of all the phosphors, irrespective of the Eu3+ and the Tb3+ contents, showed an orthorhombic structure, and the surface morphology exhibited pebble-like crystalline grains. The emission spectra of Eu3+ and Tb3+-codoped Mg2SiO4 phosphors under an ultraviolet excitation of 252 nm consisted of one intense red band at 619 nm and five weak bands at 448, 488, 598, 658, and 707 nm originating from the transitions of Eu3+, in addition to the several emission bands located at 492, 552, 592, and 628 nm arising from the transitions of Tb3+. As the Eu3+ content was increased, the intensity of the main green emission band at 552 nm decreased markedly and disappeared at 10 mol% Eu3+, when complete energy transfer from Tb3+ to Eu3+ was observed. The results suggest that the emission wavelength and the luminescent intensity of the phosphors can be tuned by modulating the Eu3+ and the Tb3+ contents incorporated into the host matrix.

Preparation and physical properties of (PVA)0.7(NaBr)0.3(H3PO4)xM solid acid membrane for phosphoric acid – Fuel cells

PubMed Central

Ahmad, F.; Sheha, E.

2012-01-01

A solid acid membranes based on poly (vinyl alcohol) (PVA), sodium bromide (NaBr) and phosphoric acid (H3PO4) were prepared by a solution casting method. The morphological, IR, electrical and optical properties of the (PVA)0.7(NaBr)0.3(H3PO4)xM solid acid membranes where x = 0.00, 0.85, 1.7, 3.4, 5.1 M were investigated. The variation of film morphology was examined by scanning electron microscopy (SEM) studies. FTIR spectroscopy has been used to characterize the structure of polymer and confirms the complexation of phosphoric acid with host polymeric matrix. The temperature dependent nature of ionic conductivity and the impedance of the polymer electrolytes were determined along with the associated activation energy. The ionic conductivity at room temperature was found to be strongly depends on the H3PO4 concentration which it has been achieved to be of the order 4.3 × 10−3 S/cm at ambient temperature. Optical measurements showed a decrease in optical band gap and an increase in band tail width with the increase of phosphoric acid. The data shows that the (PVA)0.7(NaBr)0.3(H3PO4)xM solid acid membrane is promising for intermediate temperature phosphoric acid fuel cell applications. PMID:25685413

Luminescence properties and warm white LED application of a ternary-alkaline fluoride red phosphor K2NaAlF6:Mn4+ .

PubMed

Wang, L Y; Song, E H; Deng, T T; Zhou, Y Y; Liao, Z F; Zhao, W R; Zhou, B; Zhang, Q Y

2017-08-14

Herein, a Mn 4+ ion doped complex ternary-alkaline fluoride red phosphor K 2 NaAlF 6 :Mn 4+ has been synthesized through a facile two-step co-precipitation method at room temperature. The crystal structure, morphological properties and influence of the dopant concentration, temperature and humidity on luminescence properties as well as the performance of the as-synthesized phosphor used in white light emitting diodes (WLEDs) were investigated carefully. Intense absorption in the blue region (∼460 nm) and bright narrow-band red emission (∼630 nm) with high color purity were observed from this resultant powder. Temperature-dependent investigation and reliability examination in a HTHH environment (85 °C high temperature and 85% high humidity) indicate that the obtained ternary-alkaline fluoride phosphor K 2 NaAlF 6 :Mn 4+ presents more exceptional thermal quenching behavior and longevity compared to some other binary-alkaline fluorides. Moreover, using K 2 NaAlF 6 :Mn 4+ as a red light component, a warm WLED with a preferable color rendering index (R a = 85.5) and luminous efficacy (LE = 91.2 lm W -1 ) as well as a low corresponding color temperature (CCT = 3650 K) is easily achieved, further revealing the great potential of the as-prepared ternary-alkaline fluoride red phosphor K 2 NaAlF 6 :Mn 4+ for WLED applications.

Recent progress in low-voltage cathodoluminescent materials: synthesis, improvement and emission properties.

PubMed

Li, Guogang; Lin, Jun

2014-01-01

Nowadays there are several technologies used for flat panel displays (FPDs) and the development of FPDs with enhanced energy efficiency and improved display quality is strongly required. Field emission displays (FEDs) have been considered as one of the most promising next generation flat panel display technologies due to their excellent display performance and low energy consumption. For the development of FEDs, phosphors are irreplaceable components. In the past decade, the study of highly efficient low-voltage cathodoluminescent materials, namely FED phosphors, has become the focus of enhancing energy efficiency and realizing high-quality displays. This review summaries the recent progress in the chemical synthesis and improvement of novel, rare-earth and transition metal ions activated inorganic cathodoluminescent materials in powder and thin film forms. The discussion is focused on the modification of morphology, size, surface, composition and conductivity of phosphors and the corresponding effects on their cathodoluminescent properties. Special emphases are given to the selection of host and luminescent centers, the adjustment of emission colors through doping concentration optimization, energy transfer and mono- or co-doping activator ions, the improvement of chromaticity, color stability and color gamut as well as the saturation behavior and the degradation behavior of phosphors under the excitation of a low-voltage electron beam. Finally, the research prospects and future directions of FED phosphors are discussed with recommendations to facilitate the further study of new and highly efficient low-voltage cathodoluminescent materials.

Structural refinement, band-gap analysis and optical properties of GdAlO3 nanophosphors influenced by Dy3+ ion concentrations for white light emitting device applications

NASA Astrophysics Data System (ADS)

Jisha, P. K.; Naik, Ramachandra; Prashantha, S. C.; Nagaswarupa, H. P.; Nagabhushana, H.; Basavaraj, R. B.; Sharma, S. C.; Prasad, Daruka

2016-04-01

Nanosized GdAlO3 phosphors activated with Dy3+ were prepared by a combustion method. Synthesized phosphors were calcined at 1000 °C for 3 h in order to achieve crystallinity. Powder x-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis was used to characterize the prepared product. The orthorhombic phase was observed in the XRD pattern. The particle size of the samples was calculated as around 25 nm. The SEM images show an irregular shape of the prepared nanophosphor. Functional groups of the phosphors were examined by Fourier transform infrared (FTIR) spectroscopy. Photoluminescence (PL) properties of Dy3+ doped GdAlO3 for near-ultraviolet excitation (352 nm) were studied in order to investigate the possibility of its use in white light emitting device applications. Judd-Ofelt intensity parameters, radiative transition rate (A T) and radiative lifetimes (τ rad) were evaluated from the emission spectrum by adopting a standard procedure. The Commission International de l’Eclairage (CIE) color coordinates and correlated color temperature (CCT) are studied for the optimized phosphor. It is found that the color coordinates of Dy3+ doped GdAlO3 powders fall in the white region of the CIE diagram, and the average CCT value was found to be about 6276 K. Therefore, the present phosphor is highly useful for display applications.

On the origin of temperature dependence of the emission maxima of Eu2+and Ce3+- activated phosphors

NASA Astrophysics Data System (ADS)

Yan, Shirun

2018-05-01

In this paper, temperature dependence of the emission maxima of Eu2+ and Ce3+-activated phosphors and various explanations for the thermal red-shift or blue-shift proposed by different authors are reviewed. Depending on the host lattice, doping concentration of Eu2+ or Ce3+, or the temperature range at which the PL spectrum was monitored, both the way and magnitude of emission spectrum shifting were quite different. Various explanations for the thermal shifts of the emission maxima were proposed. Nonetheless, a close inspection of a collection of the data indicates that some popular explanations seemingly plausible for the thermal red/blue-shifts of the emission maxima of Eu2+ and Ce3+-activated phosphors are highly questionable, because they either misused the Varshni equation or discussed the energy of the 5d-4f transitions of Eu2+ and Ce3+ in isolation without considering simultaneous change of the host lattice. An explanation of lattice dynamic induced thermal shifts of the emission maxima of Eu2+ and Ce3+-activated phosphors is proposed in this paper. By considering the dominant contribution to the energy of the 5d-4f transitions either from a lattice dilatation or from the interactions between the 5d electrons and phonons, the complex temperature dependences of the emission maxima of various Eu2+ and Ce3+-activated phosphors experimentally observed in literature could be explained reasonably.

Gas diffusion electrode setup for catalyst testing in concentrated phosphoric acid at elevated temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiberg, Gustav K. H., E-mail: gustav.wiberg@gmail.com, E-mail: m.arenz@chem.ku.dk; Fleige, Michael; Arenz, Matthias, E-mail: gustav.wiberg@gmail.com, E-mail: m.arenz@chem.ku.dk

2015-02-15

We present a detailed description of the construction and testing of an electrochemical cell setup allowing the investigation of a gas diffusion electrode containing carbon supported high surface area catalysts. The setup is designed for measurements in concentrated phosphoric acid at elevated temperature, i.e., very close to the actual conditions in high temperature proton exchange membrane fuel cells (HT-PEMFCs). The cell consists of a stainless steel flow field and a PEEK plastic cell body comprising the electrochemical cell, which exhibits a three electrode configuration. The cell body and flow field are braced using a KF-25 vacuum flange clamp, which allowsmore » an easy assembly of the setup. As demonstrated, the setup can be used to investigate temperature dependent electrochemical processes on high surface area type electrocatalysts, but it also enables quick screening tests of HT-PEMFC catalysts under realistic conditions.« less

Effect of Pr 3+ concentration on thermoluminescence from K 2Y 1- xPr xF 5 crystals

NASA Astrophysics Data System (ADS)

Marcazzo, J.; Santiago, M.; Caselli, E.; Nariyama, N.; Khaidukov, N. M.

2004-06-01

Thermoluminescence dosimetric characteristics of K 2YF 5 crystals doped with Pr 3+ are reported for the first time. The efficiency of the 0.5 at.% Pr 3+ doped K 2YF 5 crystal has been found to be maximum for this concentration series and three times higher than that of the commercial dosimeter TLD-700. The thermoluminescence glow curve of this novel phosphor has no appreciable fading. Furthermore, it bears linear dose response and good stability after reutilization. According to these results, K 2YF 5:Pr 3+ appears to be a promising base for developing effective phosphors for TL solid state dosimetry. In this context, the spectral composition of the TL emission is also mentioned along with the values obtained by glow curve deconvolution for the trap parameters characterising electron trap centres involved in thermoluminescence.

Preparation and evaluation of advanced electrocatalysts for phosphoric acid fuel cells

NASA Technical Reports Server (NTRS)

Stonehart, P.; Baris, J.; Pagliaro, P.

1980-01-01

Results are presented for hydrogen oxidation and hydrogen oxidation poisoned by carbon monoxide at levels between 0 and 30%. Due to the high activities that are now being observed for our platinum based electrocatalysts, the hydrogen concentrations were reduced to 10% levels in the gas supplies. Perturbation techniques were used to determine that a mechanism for the efficient operation of our porous gas diffusion electrodes is diffusion of the carbon monoxide out of the electrode structure through the electrolyte film on the electro-catalyst. A survey of the literature on platinum group materials (PGM) was carried out so that an identification of successful electrocatalysts could be made. Two PGM electrocatalysts were prepared and performance data for hydrogen oxidation in hot phosphoric acid in the presence of high carbon monoxide concentrations showed that they matched the best platinum on carbon electrocatalysts but with an electrocatalyst cost that was half of the platinum catalyst cost.

Extraction equilibrium of indium(III) from nitric acid solutions by di(2-ethylhexyl)phosphoric acid dissolved in kerosene.

PubMed

Tsai, Hung-Sheng; Tsai, Teh-Hua

2012-01-04

The extraction equilibrium of indium(III) from a nitric acid solution using di(2-ethylhexyl) phosphoric acid (D2EHPA) as an acidic extractant of organophosphorus compounds dissolved in kerosene was studied. By graphical and numerical analysis, the compositions of indium-D2EHPA complexes in organic phase and stoichiometry of the extraction reaction were examined. Nitric acid solutions with various indium concentrations at 25 °C were used to obtain the equilibrium constant of InR₃ in the organic phase. The experimental results showed that the extraction distribution ratios of indium(III) between the organic phase and the aqueous solution increased when either the pH value of the aqueous solution and/or the concentration of the organic phase extractant increased. Finally, the recovery efficiency of indium(III) in nitric acid was measured.

Gas diffusion electrode setup for catalyst testing in concentrated phosphoric acid at elevated temperatures

NASA Astrophysics Data System (ADS)

Wiberg, Gustav K. H.; Fleige, Michael; Arenz, Matthias

2015-02-01

We present a detailed description of the construction and testing of an electrochemical cell setup allowing the investigation of a gas diffusion electrode containing carbon supported high surface area catalysts. The setup is designed for measurements in concentrated phosphoric acid at elevated temperature, i.e., very close to the actual conditions in high temperature proton exchange membrane fuel cells (HT-PEMFCs). The cell consists of a stainless steel flow field and a PEEK plastic cell body comprising the electrochemical cell, which exhibits a three electrode configuration. The cell body and flow field are braced using a KF-25 vacuum flange clamp, which allows an easy assembly of the setup. As demonstrated, the setup can be used to investigate temperature dependent electrochemical processes on high surface area type electrocatalysts, but it also enables quick screening tests of HT-PEMFC catalysts under realistic conditions.

Color-tunable properties of Eu3+- and Dy3+-codoped Y2O3 phosphor particles

PubMed Central

2012-01-01

Rare-earth phosphors are commonly used in display panels, security printing, and fluorescent lamps, and have potential applications in lasers and bioimaging. In the present study, Eu3+- and Dy3+-codoped uniform-shaped Y2O3 submicron particles were prepared using the urea homogeneous precipitation method. The structure and morphology of the resulting particles were characterized by X-ray diffraction, field emission scanning electron microscope, and field emission transmission electron microscope, whereas their optical properties were monitored by photoluminescence spectroscopy. The room-temperature luminescence color emission of the synthesized particles can be tuned from red to yellow by switching the excitation wavelength from 254 to 350 nm. The luminescence intensities of red and yellow emissions could be altered by varying the dopant concentration. Strong quenching was observed at high Eu3+ and Dy3+ concentrations in the Y2O3 host lattice. PMID:23043645

Water quality in the St Croix National Scenic Riverway, Wisconsin

USGS Publications Warehouse

Graczyk, D.J.

1986-01-01

Yields for suspended sediment, total phosphorus, total nitrogen, and dissolved solids at the study stations were consistently lower than at other stations in the State. Suspendedsediment yields ranged from 1.9 to 13.3 tons per square mile. The average suspended-sediment yield for Wisconsin is 80 tons per square mile. Total phosphorous and the other constituents exhibited the same trend.

Implant decontamination with phosphoric acid during surgical peri-implantitis treatment: a RCT.

PubMed

Hentenaar, Diederik F M; De Waal, Yvonne C M; Strooker, Hans; Meijer, Henny J A; Van Winkelhoff, Arie-Jan; Raghoebar, Gerry M

2017-12-01

Peri-implantitis is known as an infectious disease that affects the peri-implant soft and hard tissue. Today, scientific literature provides very little evidence for an effective intervention protocol for treatment of peri-implantitis. The aim of the present randomized controlled trial is to evaluate the microbiological and clinical effectiveness of phosphoric acid as a decontaminating agent of the implant surface during surgical peri-implantitis treatment. Peri-implantitis lesions were treated with resective surgical treatment aimed at peri-implant granulation tissue removal, bone recontouring, and pocket elimination. Fifty-three implant surfaces in 28 patients were mechanically cleaned and treated with either 35% phosphoric etching gel (test group) or sterile saline (control group). Microbiological samples were obtained during surgery; clinical parameters were recorded at baseline and at 3 months after treatment. Data were analyzed using multi-variable linear regression analysis and multilevel statistics. Significant immediate reductions in total anaerobic bacterial counts on the implant surface were found in both groups. Immediate reduction was greater when phosphoric acid was used. The difference in log-transformed mean anaerobic counts between both procedures was not statistical significant (p = 0.108), but there were significantly less culture-positive implants after the decontamination procedure in the phosphoric acid group (p = 0.042). At 3 months post-surgery, 75% of the implants in the control group and 63.3% of the implants in the test group showed disease resolution. However, no significant differences in clinical and microbiological outcomes between both groups were found. The application of 35% phosphoric acid after mechanical debridement is superior to mechanical debridement combined with sterile saline rinsing for decontamination of the implant surface during surgical peri-implantitis treatment. However, phosphoric acid as implant surface decontaminant does not seem to enhance clinical outcomes on a 3-month follow-up. Netherlands National Trial Register, NTR5185 (www.trialregister.nl).

Investigations on surface chemical analysis using X-ray photoelectron spectroscopy and optical properties of Dy3+-doped LiNa3P2O7 phosphor

NASA Astrophysics Data System (ADS)

Munirathnam, K.; Dillip, G. R.; Chaurasia, Shivanand; Joo, S. W.; Deva Prasad Raju, B.; John Sushma, N.

2016-08-01

Near white-light emitting LiNa3P2O7:Dy3+ phosphors were prepared by a conventional solid-state reaction method. The orthorhombic crystal structure of the phosphors was confirmed using X-ray diffraction (XRD), and the valence states of the surface elements were determined from the binding energies of Li 1s, O 1s, Na 1s, P 2p, and Dy 3d by X-ray photoelectron spectroscopy (XPS). Attenuated total reflectance (ATR) - Fourier transform infrared (FT-IR) spectroscopy was employed to identify the pyrophosphate groups in the phosphors. Diffuse reflectance spectra (DRS) show the absorption bands of the Dy3+ ions in the host material. Intense blue (481 nm) and yellow (575 nm) emissions were obtained at an excitation wavelength of 351 nm and are attributed to the 4F9/2 → 6H15/2 and 4F9/2 → 6H13/2 transitions of Dy3+ ions, respectively. The combination of these two intense bands generates light emission in the near-white region of the chromaticity diagram.

Testing of Candidate Polymeric Materials for Compatibility with Pure Alternate Pretreat as Part of the Universal Waste Management System (UWMS)

NASA Technical Reports Server (NTRS)

Wingard, C. D.

2018-01-01

The Universal Waste Management System (UWMS) is an improved Waste Collection System for astronauts living and working in low Earth orbit spacecraft. Polymeric materials used in water recovery on International Space Station are regularly exposed to phosphoric acid-treated 'pretreated' urine. Polymeric materials used in UWMS are not only exposed to pretreated urine, but also to concentrated phosphoric acid with oxidizer before dilution known as 'pure pretreat.' Samples of five different polymeric materials immersed in pure pretreat for 1 year were tested for liquid compatibility by measuring changes in storage modulus with a dynamic mechanical analyzer.

The effect of enriched chicory inulin on liver enzymes, calcium homeostasis and hematological parameters in patients with type 2 diabetes mellitus: A randomized placebo-controlled trial.

PubMed

Farhangi, Mahdieh Abbasalizad; Javid, Ahmad Zare; Dehghan, Parvin

2016-08-01

Type 2 diabetic mellitus (T2DM) as one of the main causes of morbidity and mortality is associated with immune system disturbances and metabolic abnormalities. In the current study we aimed to evaluate the effects of enriched chicory inulin supplementation on liver enzymes, serum calcium and phosphorous concentrations and hematological parameters in patients with T2DM. Forty-six diabetic females patients were randomly allocated into intervention (n=27) and control (n=22) groups. Subjects in the intervention group received a daily dose of 10g of chicory and subjects in control group received a placebo for two months. Anthropometric variables, glucose homeostasis, hematological parameters and metabolic indices including serum alanine aminotransfersae (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), calcium and phosphorous as well as creatinine concentrations, glomerular filtration rate (GFR) and blood pressure were assessed at the beginning and end of the trial. Significant reductions in fasting serum glucose (FSG), Hb A1C, AST and ALP concentrations were observed in chicory-treated group. Systolic and diastolic blood pressures were also reduced in chicory-treated group. Serum calcium significantly increased after chicory supplementation but no change in placebo treated group has been occurred (P=0.014). Supplementation with enriched chicory for two months significantly reduced hematocrit and mean corpuscular volume (MCV) values (P<0.05). Changes in serum insulin, creatinine and GFR were not significant. The present study showed beneficial effects of oligofructose-enriched chicory on the improvement of the glucose and calcium homeostasis, liver function tests, blood pressure and reduction in hematologic risk factors of diabetes in female patients with T2DM. Further studies in both genders are needed to generalize these findings to total population. Copyright © 2016 Primary Care Diabetes Europe. Published by Elsevier Ltd. All rights reserved.

Preparation and evaluation of advanced catalysts for phosphoric acid fuel cells

NASA Technical Reports Server (NTRS)

Stonehart, P.; Baris, J.; Hockmuth, J.; Pagliaro, P.

1984-01-01

The platinum electrocatalysts were characterized for their crystallite sizes and the degree of dispersion on the carbon supports. One application of these electrocatalysts was for anodic oxidation of hydrogen in hot phosphoric acid fuel cells, coupled with the influence of low concentrations of carbon monoxide in the fuel gas stream. In a similar way, these platinum on carbon electrocatalysts were evaluated for oxygen reduction in hot phosphoric acid. Binary noble metal alloys were prepared for anodic oxidation of hydrogen and noble metal-refractory metal mixtures were prepared for oxygen reduction. An exemplar alloy of platinum and palladium (50/50 atom %) was discovered for anodic oxidation of hydrogen in the presence of carbon monoxide, and patent disclosures were submitted. For the cathode, platinum-vanadium alloys were prepared showing improved performance over pure platinum. Preliminary experiments on electrocatalyst utilization in electrode structures showed low utilization of the noble metal when the electrocatalyst loading exceeded one weight percent on the carbon.

The influence of SRT on phosphorus removal and sludge characteristics in the HA-A/A-MCO sludge reduction process

NASA Astrophysics Data System (ADS)

Zuo, N.; Ji, F. Y.

2013-02-01

By researching the influence of sludge age (SRT) on phosphorous removal and sludge characteristics in the HA-A/A-MCO (hydrolysis-acidification-anaerobic/anoxic-multistep continuous oxic tank) process, which has the effect of simultaneous phosphorous and nitrogen removal and sludge reduction, it is found that extended SRT is helpful for improving the ability of anaerobic phosphorous release and chemical recovery of phosphate, but the hosphorous removal efficiency is not affected. Extended SRT causes the system to have even more active sludge; it can also lead to the system having a powerful ability of biochemical reaction by using superiority of concentration. Meanwhile, extended SRT can still reduce sludge yield. Extended SRT cannot make soluble metabolic product (SMP) accumulate in the reactor, so that the pollutant removal power is reduced; it also cannot affect the activity of the sludge. However, extended SRT is able to make the coagulation of the sludge hard, and cause the sludge volume index value increase, but cannot cause sludge bulking.

Luminescent Enhancement of Na+ and Sm3+ Co-doping Reddish Orange SrCa3Si2O8 Phosphors

NASA Astrophysics Data System (ADS)

Chun, Fengjun; Zhang, Binbin; Li, Wen; Liu, Honggang; Deng, Wen; Chu, Xiang; Osman, Hanan; Zhang, Haitao; Yang, Weiqing

2018-04-01

Reddish orange SrCa3Si2O8 phosphors, prepared by the facile solid state reaction method, are a luminescent enhancement of Na+ and Sm3+ co-doping luminescent material. Na+ was designed to compensate the charge imbalance of Sm3+ ion substituting for the Sr2+ ion of orthorhombic SrCa3Si2O8 crystals. The results suggest that Na+ can effectively enhance the luminescent intensity of the reddish orange light peaked at about 562 nm (4 G 5/2 → 6 H 5/2), 600 nm (4 G 5/2 → 6 H 7/2) and 645 nm (4 G 5/2 → 6 H 9/2) excited by the near ultraviolet excited light 404 nm (4 L 13/2 → 6 H 5/2). The energy transfer has been further verified by the florescence lifetime. Additionally, the luminescent lifetime τ of as-grown phosphors was separated into two parts, a rapid lifetime and a slow lifetime. The average lifetime results ranged from 2.098 to 1.329 ms which were influenced by the concentration of Sm3+ doping. The systematic researches of as-grown phosphors have clearly suggested a potential application for white-light-emitting diodes ( w-LEDs).

Crystal structure, energy transfer and tunable luminescence properties of Ca8ZnCe(PO4)7:Eu2+,Mn2+ phosphor

NASA Astrophysics Data System (ADS)

Ding, Chong; Tang, Wanjun

2018-02-01

Single-phased Ca8ZnCe(PO4)7:Eu2+,Mn2+ phosphors with whitlockite-type structure have been prepared via the combustion-assisted synthesis technique. The XRD pattern show that the as-obtained phosphors crystallize in a trigonal phase with space group of R-3c (161). Ca8ZnCe(PO4)7 host is full of sensitizers (Ce3+) and the Ce3+ emission at different lattice sites has been discussed. The efficient energy transfers from Ce3+ ions to Eu2+/Mn2+ ions and from Eu2+ to Mn2+ have been validated. Under UV excitation, the emitting color of Ca8ZnCe(PO4)7:Eu2+/Mn2+ samples can be modulated from violet blue to green and from violet blue to red-orange by the energy transfers of Ce3+→Eu2+ and Ce3+→Mn2+, respectively. Additionally, white emission has been obtained through adjusting the relative concentrations of Eu2+ and Mn2+ ions in the Ca8ZnCe(PO4)7 host under UV excitation. These results indicate that as-prepared Ca8ZnCe(PO4)7:Eu2+,Mn2+ may be a potential candidate as color-tunable white light-emitting phosphors.

Controlling Blue and Red Light Emissions from Europium (Eu2+)/Manganese (Mn2+)-Codoped Beta-Tricalcium Phosphate [β-Ca3(PO4)2 (TCP)] Phosphors

NASA Astrophysics Data System (ADS)

Van, Hoang Nhu; Hoan, Bui Thi; Nguyen, Khoi Thi; Tam, Phuong Dinh; Huy, Pham Thanh; Pham, Vuong-Hung

2018-03-01

Tunable light emission from europium (Eu2+)/manganese (Mn2+)-codoped beta-tricalcium phosphate [β-Ca3(PO4)2 (TCP)] has been investigated as a function of the Mn2+ and Eu2+ concentrations and annealing temperature. Eu2+/Mn2+-doped TCP phosphor (Eu/Mn-TCP) was synthesized by coprecipitation method followed by thermal annealing at temperature up to 1100°C. The Eu2+/Mn2+-doped TCP particles have diameter of about 1 μm. The light emission from TCP is enhanced in the sample with 7.5 mol.% Mn2+ and 0.3 mol.% Eu2+ annealed in Ar + 5% H2 atmosphere at 1100°C. The blue band at 430 nm is attributed to the 4f 6 5d 1-4f 7 transition of Eu2+. The sharp peak at 660 nm is ascribed to the 4T1-6A1 transition of Mn2+ in TCP. These results suggest codoping of Eu2+/Mn2+ to TCP phosphor to obtain β-Ca3(PO4)2:Eu2+,Mn2+ phosphors with tunable luminescence, having potential applications in agricultural lighting.

Energy transfer and color tunable emission in Tb3 +,Eu3 + co-doped Sr3LaNa(PO4)3F phosphors

NASA Astrophysics Data System (ADS)

Li, Shuo; Guo, Ning; Liang, Qimeng; Ding, Yu; Zhou, Huitao; Ouyang, Ruizhuo; Lü, Wei

2018-02-01

A group of color tunable Sr3LaNa(PO4)3F:Tb3 +,Eu3 + phosphors were prepared by conventional high temperature solid state method. The phase structures, luminescence properties, fluorescence lifetimes and energy transfer were investigated in detail. Under 369 nm excitation, owing to efficient energy transfer of Tb3 + → Eu3 +, the emission spectra both have green emission of Tb3 + and red emission of Eu3 +. An efficient energy transfer occur in Tb3 +, Eu3 + co-doped Sr3LaNa(PO4)3F phosphors. The most possible mechanism of energy transfer is dipole-dipole interaction by Dexter's theoretical model. The energy transfer of Tb3 + and Eu3 + was confirmed by the variations of emission and excitation spectra and Tb3 +/Eu3 + decay lifetimes in Sr3LaNa(PO4)3F:Tb3 +,Eu3 +. The color tone can tuned from yellowish-green through yellow and eventually to reddish-orange with fixed Tb3 + content by changing Eu3 + concentrations. The results show that the prepared Tb3 +, Eu3 + co-doped color tunable Sr3LaNa(PO4)3F phosphor can be used for white LED.

Removal of ammonia from landfill leachate by struvite precipitation with the use of low-cost phosphate and magnesium sources.

PubMed

Huang, Haiming; Xiao, Dean; Zhang, Qingrui; Ding, Li

2014-12-01

This paper presents a study concerning ammonia removal from landfill leachate by struvite precipitation with the use of waste phosphoric acid as the phosphate source. The results indicated that the Al(3+) ions present in the waste phosphoric acid significantly affected the struvite precipitation, and a removal ratio of ammonia close to that of pure phosphate salts could be achieved. Nevertheless, large amounts of NaOH were necessary to neutralize the H(+) present in the waste phosphoric acid. To overcome this problem, a low-cost magnesium source was proposed to be used as well as an alkali reagent in the struvite precipitation. The ammonia removal ratios were found to be 83%, with a remaining phosphate of 56 mg/L, by dosing the low-cost MgO in the Mg:N:P molar ratio of 3:1:1. An economic analysis showed that using waste phosphoric acid plus the low-cost MgO could save chemical costs by 68% compared with the use of pure chemicals. Post-treatment employment of a biological anaerobic filter process demonstrated that the high concentration of Mg(2+) remaining in the effluent of the struvite precipitation has no inhibitory effect on the performance of the biological treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

Photon up-conversion increases biomass yield in Chlorella vulgaris.

PubMed

Menon, Kavya R; Jose, Steffi; Suraishkumar, Gadi K

2014-12-01

Photon up-conversion, a process whereby lower energy radiations are converted to higher energy levels via the use of appropriate phosphor systems, was employed as a novel strategy for improving microalgal growth and lipid productivity. Photon up-conversion enables the utilization of regions of the solar spectrum, beyond the typical photosynthetically active radiation, that are usually wasted or are damaging to the algae. The effects of up-conversion of red light by two distinct sets of up-conversion phosphors were studied in the model microalgae Chlorella vulgaris. Up-conversion by set 1 phosphors led to a 2.85 fold increase in biomass concentration and a 3.2 fold increase in specific growth rate of the microalgae. While up-conversion by set 2 phosphors resulted in a 30% increase in biomass and 12% increase in specific intracellular neutral lipid, while the specific growth rates were comparable to that of the control. Furthermore, up-conversion resulted in higher levels of specific intracellular reactive oxygen species in C. vulgaris. Up-conversion of red light (654 nm) was shown to improve biomass yields in C. vulgaris. In principle, up-conversion can be used to increase the utilization range of the electromagnetic spectrum for improved cultivation of photosynthetic systems such as plants, algae, and microalgae. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Colour gamut enhancement with remote light conversion mechanism

NASA Astrophysics Data System (ADS)

Koseoglu, D.; Sezer, Y. S.; Karsli, K.

2018-01-01

The backlight unit spectrum of liquid crystal displays (LCD) directly affects the colour gamut. With the invention of GaN based blue light emitting diodes (LED), phosphors and quantum dots (QD) have gained considerable scientific interest due to their broad range of applications especially in lighting and display technologies. These phosphors and QDs are used to convert the blue light of the LEDs into white in general lighting. On the other hand, in display systems, they are used to generate red and green bands. There are different application methods such as on-chip and remote configurations. In this study, we concentrate on remote phosphor and QD backlight configurations where the light conversion is done away from the chips. In our display designs, we used GaN based blue LED lateral chips as an excitation source, on the other hand, light conversion layers were placed in backlight units as a thin film for the emission of green and red bands. The mixing ratios of these composite layers were arranged to match the emission spectrum of the blue LEDs and the light conversion layer to the colour filters of the LCD, so that the green, blue, and red bands efficiently widens the colour space. The results were also compared with the on-chip phosphor arrangements.

Distribution and contamination status of chromium in surface sediments of northern Kaohsiung Harbor, Taiwan.

PubMed

Dong, Cheng-Di; Chen, Chiu-Wen; Chen, Chih-Feng

2013-07-01

The distribution, enrichment, accumulation, and potential ecological risk of chromium (Cr) in the surface sediments of northern Kaohsiung Harbor, Taiwan, China were investigated. Sediment samples from ten locations located between the river mouths and harbor entrance of northern Kaohsiung Harbor were collected quarterly in 2011 and characterized for Cr, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease, and grain size. Results showed that the Cr concentrations varied from 27.0 to 361.9 mg/kg with an average of (113.5 +/- 87.0) mg/kg. High Cr concentration was observed near the Jen-Gen River mouth. The mean Cr concentration was high at 255.5 mg/kg, which was at least 2 to 7 times than that of other sites. This might imply significant Cr contribution from upstream receiving tanneries wastewater into the Jen-Gen River. The spatial distribution of Cr reveals relatively high in the river mouth region, especially in Jen-Gen River, and gradually diminishes toward the harbor entrance region. This indicates that the major sources of Cr pollution from upstream industrial and municipal wastewaters discharged along the river bank; and Cr may drift with sea current and be dispersed into open sea. Moreover, Cr concentrations correlated closely to the physical-chemical properties of the sediments, which suggested the influence of industrial and municipal wastewaters discharged from the neighboring industrial parks and river basins. Results from the enrichment factor and geo-accumulation index analyses imply that the Jen-Gen River sediments can be characterized as moderate enrichment and none to medium accumulation of Cr, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk. The results can provide valuable information to developing future strategies for the management of river mouth and harbor.

Digital imaging with solid state x-ray image intensifiers

NASA Astrophysics Data System (ADS)

Damento, Michael A.; Radspinner, Rachel; Roehrig, Hans

1999-10-01

X-ray cameras in which a CCD is lens coupled to a large phosphor screen are known to suffer from a loss of x-ray signal due to poor light collection from conventional phosphors, making them unsuitable for most medical imaging applications. By replacing the standard phosphor with a solid-state image intensifier, it may be possible to improve the signal-to-noise ratio of the images produced with these cameras. The solid-state x-ray image intensifier is a multi- layer device in which a photoconductor layer controls the light output from an electroluminescent phosphor layer. While prototype devices have been used for direct viewing and video imaging, they are only now being evaluated in a digital imaging system. In the present work, the preparation and evaluation of intensifiers with a 65 mm square format are described. The intensifiers are prepared by screen- printing or doctor blading the following layers onto an ITO coated glass substrate: ZnS phosphor, opaque layer, CdS photoconductor, and carbon conductor. The total thickness of the layers is approximately 350 micrometers , 350 VAC at 400 Hz is applied to the device for operation. For a given x-ray dose, the intensifiers produce up to three times the intensity (after background subtracting) of Lanex Fast Front screens. X-ray images produced with the present intensifiers are somewhat noisy and their resolution is about half that of Lanex screens. Modifications are suggested which could improve the resolution and noise of the intensifiers.

Determination of trace concentrations of chlorine in aqueous solutions by high-resolution continuum source graphite furnace molecular absorption spectrometry

NASA Astrophysics Data System (ADS)

Machyňák, Ľubomír; Čacho, František; Němeček, Martin; Beinrohr, Ernest

2016-11-01

Trace concentrations of total chlorine were determined by means of molecular absorption of indium mono-chloride (InCl) at 267.217 nm using high-resolution continuum source graphite furnace molecular absorption spectrometry. The effects of chemical modifiers and the amount of In on the sensitivity and accuracy were investigated. The optimum pyrolysis and vaporization temperatures were 600 °C and 1400 °C, respectively. The limit of detection and characteristic mass were found to be 0.10 ng and 0.21 ng, respectively. Potential non-spectral and spectral interferences were tested for various metals and non-metals at concentrations up to 50 mg L- 1 and for phosphoric, sulphuric and nitric acids. No spectral interferences were observed. Significant non-spectral interferences were observed with F, Br, and I at concentrations higher than 1 mg L- 1, 5 mg L- 1 and 25 mg L- 1, respectively, which is probably caused by formation of competitive indium halogen molecules. Higher concentrations of mineral acids depressed the signal owing to the formation of volatile HCl. The calibration curve was linear in the range between 0.3 and 10 ng with a correlation coefficient of R = 0.993. The elaborated method was used for the chlorine determination in various waters and a drug sample.

Spatiotemporal Dynamics of Biogeochemical Species around Karadiyana Solid Waste Landfill, Sri Lanka

NASA Astrophysics Data System (ADS)

Koliyabandara, P. A.; Cooray, P. L. A. T.; Liyanage, S.; Siriwardana, C.

2017-12-01

Leachate from solid waste landfills is a significant environmental issue throughout the world. Most of the developed countries have strict guidelines for solid waste landfills as opposed to the open solid waste dumps in developing countries. Karadiyana solid waste management facility is located in Western province, Sri Lanka having a total area about 25 acres. Several Local Authorities use this facility as the final disposal site for their daily collected garbage. About 575 tons/day of Municipal Solid Waste reach the project site. This novel study was carried out to understand the spatiotemporal variation of nutrients around the site surrounded by a marshy land which directly has a connection to Weras River. Leachate, surface water and ground water samples were collected from pre-determined locations and analyzed to assess the interaction of leachate with surrounding water bodies. Sample locations were selected based on topography, areas close to dumpsite and flow regimes. Sampling was done monthly over eight months starting from September 2016 data and they were preserved, and analyzed according to the Standard Methods for the Examination of Water and wastewater analysis. Ammonia Nitrogen, Nitrate Nitrogen, Total Phosphorous (TP) of surface water ranged in between 0.08-320, 10-6000, 0.2-50 mg/L. For leachate samples, the above parameters varied in the range of 0.22-320, 18-13000 and 0.04-15 mg/L. Highest concentrations for Nitrogenous species and Phosphorous were observed at the sampling point closer to the site (latitude 6.816538 and longitude of 79.902250). Higher concentrations measured during the rainy period may be attributed to rainwater that infiltrated into the landfill that promotes solubilisation of pollutants and enhanced leaching of nutrients from actively decomposing waste mass into leachates. Interestingly, though high concentration of nitrogen and TP observed in surface waters, dense algae growth was not observed. This may be due to the presence of Cu at level in the range of 0.1 to 0.2 ppm. Ammonia Nitrogen, Nitrate Nitrogen, TP in ground water of monitoring wells ranged in between 400-500, 40-62, 1.6- 160 mg/L. Our results emphasizes there is a greater threat by the cumulative load discharged to the river annually. Proper treatment prior to disposal is recommended.

[An analysis of nutritional and harmful components of vegetables grown in plastic greenhouses].

PubMed

Yao, H; Yan, W; Li, G; Chen, Y; Guo, W; Wang, G; Xu, Z; Feng, C; Liu, K; Jin, D

1999-09-01

To study the changes in nutritional and harmful components of vegetables grown in plastic greenhouses. In plastic greenhouses, microclimate and air concentrations of carbon monoxide, carbon dioxide, fluoride and respirable particulate were measured, and chlorophyll, total sugar, crude fiber, nitrite, fluoride, arsenic and some mineral elements in vegetables were determined as compared with those grown in the open-air fields. Greenhouse appeared a lower wind speed and darker illumination. Contents of chlorophyll a an b, total chlorophyll, reduced vitamin C, crude fiber in vegetables grown in greenhouse all were lower than those grown in open-air fields. Contents of potassium, calcium, magnesium, iron, zinc, copper and phosphorous were all lower in the vegetables grown in greenhouse than those grown in open-air fields. The contents of chlorophyll reducing Vitamin C. Lower wind speed and inadequate illumination in greenhouse affected photosynthesis and uptake of water in vegetables causing changes in their nutritional components. But, no contamination of burning coal was found in vegetables grown in greenhouse.

Performance and cost evaluation of constructed wetland for domestic waste water treatment.

PubMed

Deeptha, V T; Sudarsan, J S; Baskar, G

2015-09-01

Root zone treatment through constructed wetlands is an engineered method of purifying wastewater. The aim of the present research was to study the potential of wetland plants Phragmites and Typha in treatment of wastewater and to compare the cost of constructed wetlands with that of conventional treatment systems. A pilot wetland unit of size 2x1x0.9 m was constructed in the campus. 3x3 rows of plants were transplanted into the pilot unit and subjected to wastewater from the hostels and other campus buildings. The raw wastewater and treated wastewater were collected periodically and tested for Total nitrogen (TN),Total Phosphorous (TP), Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD). It was observed that this pilot unit reduced the concentrations of TN, TP, BOD and COD by 76, 73, 83 and 86%, respectively, on an average. Root zone system achieved standards for tertiary treatment with low operating costs, low maintenance costs, enhance the landscape, provide a natural habitat for birds, and did not emit any odour.

Evaluation of natural materials as exogenous carbon sources for biological treatment of low carbon-to-nitrogen wastewater.

PubMed

Ramírez-Godínez, Juan; Beltrán-Hernández, Icela; Álvarez-Hernández, Alejandro; Coronel-Olivares, Claudia; Contreras-López, Elizabeth; Quezada-Cruz, Maribel; Vázquez-Rodríguez, Gabriela

2015-01-01

In the bacterial processes involved in the mitigation of nitrogen pollution, an adequately high carbon-to-nitrogen (C : N) ratio is key to sustain denitrification. We evaluated three natural materials (woodchips, barley grains, and peanut shells) as carbon sources for low C : N wastewater. The amount of organic matter released from these materials to aqueous media was evaluated, as well as their pollution swapping potential by measuring the release of total Kjeldahl nitrogen, N-NH4 (+), NO2 (-), and NO3 (-), and total phosphorous. Barley grains yielded the highest amount of organic matter, which also showed to be the most easily biodegradable. Woodchips and peanut shells released carbon rather steadily and so they would not require frequent replenishment from biological reactors. These materials produced eluates with lower concentrations of nutrients than the leachates from barley grains. However, as woodchips yielded lower amounts of suspended solids, they constitute an adequate exogenous source for the biological treatment of carbon-deficient effluents.

Evaluation of Natural Materials as Exogenous Carbon Sources for Biological Treatment of Low Carbon-to-Nitrogen Wastewater

PubMed Central

Ramírez-Godínez, Juan; Beltrán-Hernández, Icela; Álvarez-Hernández, Alejandro; Coronel-Olivares, Claudia; Contreras-López, Elizabeth; Quezada-Cruz, Maribel

2015-01-01

In the bacterial processes involved in the mitigation of nitrogen pollution, an adequately high carbon-to-nitrogen (C : N) ratio is key to sustain denitrification. We evaluated three natural materials (woodchips, barley grains, and peanut shells) as carbon sources for low C : N wastewater. The amount of organic matter released from these materials to aqueous media was evaluated, as well as their pollution swapping potential by measuring the release of total Kjeldahl nitrogen, N-NH4 +, NO2 −, and NO3 −, and total phosphorous. Barley grains yielded the highest amount of organic matter, which also showed to be the most easily biodegradable. Woodchips and peanut shells released carbon rather steadily and so they would not require frequent replenishment from biological reactors. These materials produced eluates with lower concentrations of nutrients than the leachates from barley grains. However, as woodchips yielded lower amounts of suspended solids, they constitute an adequate exogenous source for the biological treatment of carbon-deficient effluents. PMID:26495313

Li{sub 3}Gd{sub 3}Te{sub 2}O{sub 12}:Eu{sup 3+}- an intense red phosphor for solid state lighting applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tiwari, Hansnath; Asiri Naidu, S.; Varadaraju, U.V., E-mail: varada@iitm.ac.in

Li{sub 3}Gd{sub 3−3x}Eu{sub 3x}Te{sub 2}O{sub 12} (x=0.05−1.0) phases with garnet structure were synthesized by high temperature solid state reaction and the photoluminescence properties were investigated. The appearance of bands due to intra 4 f transitions of Gd{sup 3+} in the excitation spectra recorded by monitoring the 612 nm emission line of the activator indicates Gd{sup 3+}→Eu{sup 3+} energy transfer in this host lattice. Under 395 nm excitation, the electric dipole transition is predominant in the emission spectrum of Eu{sup 3+} and is in agreement with the C{sub 2} point group (noncentrosymmetric) of the EuO{sub 8} polyhedron. The critical concentration ofmore » the Eu{sup 3+} activator in this series was found to be 0.6 (x=0.2) above which, concentration quenching occurs. The emission intensity of the phosphor composition, Li{sub 3}Gd{sub 2.4}Eu{sub 0.6}Te{sub 2}O{sub 12} is ~4 times that of the commercial sample of Y{sub 2}O{sub 3}:Eu{sup 3+} phosphor. - Highlights: • New Eu{sup 3+} doped garnet. • Intense electric dipole emission. • Gd{sup 3+}→Eu{sup 3+} energy transfer.« less

Structural and optical properties of Tb and Na-Tb co-doped Ca3V2O8 phosphors prepared by sol-gel process

NASA Astrophysics Data System (ADS)

Parab, Shambhu S.; Salker, A. V.

2018-01-01

A malic acid assisted sol-gel route was successfully employed to prepare two distinct series of green emitting Ca3V2O8 phosphors. In the first series, Tb was solely doped whereas in the second series Na and Tb were doped simultaneously in the Ca3V2O8 crystal lattice. X-ray diffraction studies proved the utility of adopted preparative method by confirming the monophasic formation of all compounds from both the series. Spectral analysis like Raman spectroscopy, UV-DRS were undertaken to analyse the local structure, crystallinity and absorptive characteristics. XPS validated the presence of desired oxidation states of all the elements present. Finally, photoluminescence studies were done to elucidate the scope of prepared compounds as green emitting phosphors and also to understand the effect of both doping schemes on the luminescence. Intense green emission was observed in both the cases. Tb concentration of 0.08 was found to be optimum in case of Tb singly doped compounds whereas Tb = 0.12 showed highest intensity among the Na-Tb co-doped samples. Moreover, a red shift in the excitation wavelength was observed after Na doping signifying a change in the local electronic environment which in turn has affected the luminescence pattern. Local crystallinity and vacancy concentrations were found to have a major say on the emission intensities.

Photoluminescence properties of aeschynite-type LaNbTiO6:RE3+ (RE = Tb, Dy, Ho) down-converting phosphors.

PubMed

Ma, Qian; Lu, Mengkai; Yang, Ping; Zhang, Aiyu; Cao, Yongqiang

2014-06-01

In this study, a series of LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) down-converting phosphors were synthesized using a modified sol-gel combustion method, and their photoluminescence (PL) properties were investigated as a function of activator concentration and annealing temperature. The resultant particles were characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, UV/Vis diffuse reflectance spectroscopy and PL spectra. The highly crystalline LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) phosphors with an average size of 200-300 nm obtained at 1100°C have an orthorhombic aeschynite-type structure and exhibit the highest luminescent intensity in our study range. The emission spectra of LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) phosphors under excitations at UV/blue sources are mainly composed of characteristic peaks arising from the f-f transitions of RE(3+), including 489 nm ((5) D4 → (7) F6) and 545 nm ((5) D4 → (7) F5) for Tb(3+), 476 and 482 nm ((4) F9/2 → (6) H15/2) and 571 nm ((4) F9/2 → (6) H13/2) for Dy(3+), and 545 nm ((5) F4 + (5) S2 → (5) I8) for Ho(3+), respectively. The luminescent mechanisms were further investigated. It can be expected that these phosphors are of intense interest and potential importance for many optical applications. Copyright © 2013 John Wiley & Sons, Ltd.

Sol-gel syntheses, luminescence, and energy transfer properties of α-GdB5O9:Ce(3+)/Tb(3+) phosphors.

PubMed

Sun, Xiaorui; Gao, Wenliang; Yang, Tao; Cong, Rihong

2015-02-07

Sol-gel method was applied to prepare homogenous and highly crystalline phosphors with the formulas α-GdB5O9:xTb(3+) (0 ≤ x ≤ 1), α-Gd1-xCexB5O9 (0 ≤ x ≤ 0.40), α-GdB5O9:xCe(3+), 0.30Tb(3+) (0 ≤ x ≤ 0.15) and α-GdB5O9:0.20Ce(3+), xTb(3+) (0 ≤ x ≤ 0.10). The success of the syntheses was proved by the linear shrinkage or expansion of the cell volumes against the substitution contents. In α-GdB5O9:xTb(3+), an efficient energy transfer from Gd(3+) to Tb(3+) was observed and there was no luminescence quenching. The exceptionally high efficiency of the f-f excitations of Tb(3+) implies that these phosphors may be good green-emitting UV-LED phosphors. For α-Gd1-xCexB5O9, Ce(3+) absorbs the majority of the energy and transfers it to Gd(3+). Therefore, the co-doping of Ce(3+) and Tb(3+) leads to a significant enhancement in the green emission of Tb(3+). Our current results together with the study on α-GdB5O9:xEu(3+) in the literature indicate that α-GdB5O9 is a good phosphor host with advantages including controllable preparation, diverse cationic doping, the absence of concentration quenching, and effective energy transfer.

Formation of Deep Electron Trap by Yb3+ Codoping Leads into Super-Long Persistent Luminescence in Ce3+-doped Yttrium Aluminum Gallium Garnet Phosphors.

PubMed

Ueda, Jumpei; Miyano, Shun; Tanabe, Setsuhisa

2018-05-23

The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Cr 3+ compound is one of the brightest persistent phosphors, but its persistent luminescence (PersL) duration is not so long due to the relatively shallow Cr 3+ electron trap. Comparing the vacuum referred binding energy of the electron trapping state by Cr 3+ and those by lanthanide ions, we selected Yb 3+ as a deeper electron trapping center. The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Yb 3+ phosphors show Ce 3+ :5d→4f green persistent luminescence after ceasing blue light excitation. The formation of Yb 2+ was confirmed by the increased intensity of absorption at 585 nm during the charging process. This result indicates that the Yb 3+ ions act as electron traps by capturing an electron. From the thermoluminescence glow curves, it was found the Yb 3+ trap makes much deeper electron trap with 1.01 eV depth than the Cr 3+ electron trap with 0.81 eV depth. This deeper Yb 3+ trap provides much slower detrapping rate of filled electron traps than the Cr 3+ -codoped persistent phosphor. In addition, by preparing transparent ceramics and optimizing Ce 3+ and Yb 3+ concentrations, the Y 3 Al 2 Ga 3 O 12 :Ce 3+ (0.2%)-Yb 3+ (0.1%) as-made transparent ceramic phosphor showed super long persistent luminescence for over 138.8 hours after ceasing blue light charging.

Evaluation of phytochemical content, nutritional value and antioxidant activity of Phanji - Rivea hypocrateriformis (Desr.) Choisy leaf

PubMed Central

Borkar, Sneha D.; Naik, Raghavendra; Shukla, Vinay J.; Acharya, Rabinarayan

2015-01-01

Background: Rivea hypocrateriformis (Desr.) Choisy is known to be the source plant of Phanji, a classically delineated leafy vegetable which is till date used by some hill dwelling Kandha tribes of Odisha. Though it is in use since a long time, it is not yet evaluated for its nutritive value. Aim: The leaves of R. hypocrateriformis were evaluated for its nutritive value and antioxidant potential. Materials and Methods: The in vitro antioxidant properties of the leaf of R. hypocrateriformis were screened through 1,1-diphenyl-2-picrylhydrazyl (DPPH) and total antioxidant capacity. Phytochemicals, crude protein, fat, carbohydrate, energy value, and mineral content of the leaves of the plant were evaluated with standard procedures. Results: In phytochemical analysis, tannin, alkaloids, flavonoids, and carbohydrates were present in leaf powder of R. hypocrateriformis. Energy content was found to be highest (331.54 kcals/100 g). Carbohydrate, fat, protein, calcium, magnesium, phosphorous, and zinc were present in 57.63%, 2.66%, 19.27%, 0.99%, 0.34%, 0.32%, and 0.011%, respectively. The IC50 values of the extract and ascorbic acid were found to be 254 ± 5.29 μg/ml and 11.67 ± 0.58 μg/ml, respectively. Percentage scavenging of DPPH radical was found to rise with increasing concentration of the crude extract. Total antioxidant capacity of the extract was found to be 111.30 ± 0.003 mcg. Conclusion: The results of this study indicate that the leaves of R. hypocrateriformis contain secondary metabolites such as tannin and possess mild antioxidant properties. Nutritional analysis indicates the presence of energy in highest amount, carbohydrates, proteins, fats, calcium, phosphorous, zinc, and magnesium. PMID:27313417

Evaluation of phytochemical content, nutritional value and antioxidant activity of Phanji - Rivea hypocrateriformis (Desr.) Choisy leaf.

PubMed

Borkar, Sneha D; Naik, Raghavendra; Shukla, Vinay J; Acharya, Rabinarayan

2015-01-01

Rivea hypocrateriformis (Desr.) Choisy is known to be the source plant of Phanji, a classically delineated leafy vegetable which is till date used by some hill dwelling Kandha tribes of Odisha. Though it is in use since a long time, it is not yet evaluated for its nutritive value. The leaves of R. hypocrateriformis were evaluated for its nutritive value and antioxidant potential. The in vitro antioxidant properties of the leaf of R. hypocrateriformis were screened through 1,1-diphenyl-2-picrylhydrazyl (DPPH) and total antioxidant capacity. Phytochemicals, crude protein, fat, carbohydrate, energy value, and mineral content of the leaves of the plant were evaluated with standard procedures. In phytochemical analysis, tannin, alkaloids, flavonoids, and carbohydrates were present in leaf powder of R. hypocrateriformis. Energy content was found to be highest (331.54 kcals/100 g). Carbohydrate, fat, protein, calcium, magnesium, phosphorous, and zinc were present in 57.63%, 2.66%, 19.27%, 0.99%, 0.34%, 0.32%, and 0.011%, respectively. The IC50 values of the extract and ascorbic acid were found to be 254 ± 5.29 μg/ml and 11.67 ± 0.58 μg/ml, respectively. Percentage scavenging of DPPH radical was found to rise with increasing concentration of the crude extract. Total antioxidant capacity of the extract was found to be 111.30 ± 0.003 mcg. The results of this study indicate that the leaves of R. hypocrateriformis contain secondary metabolites such as tannin and possess mild antioxidant properties. Nutritional analysis indicates the presence of energy in highest amount, carbohydrates, proteins, fats, calcium, phosphorous, zinc, and magnesium.

Development of urban runoff model FFC-QUAL for first-flush water-quality analysis in urban drainage basins.

PubMed

Hur, Sungchul; Nam, Kisung; Kim, Jungsoo; Kwak, Changjae

2018-01-01

An urban runoff model that is able to compute the runoff, the pollutant loadings, and the concentrations of water-quality constituents in urban drainages during the first flush was developed. This model, which is referred to as FFC-QUAL, was modified from the existing ILLUDAS model and added for use during the water-quality analysis process for dry and rainy periods. For the dry period, the specifications of the coefficients for the discharge and water quality were used. During rainfall, we used the Clark and time-area methods for the runoff analyses of pervious and impervious areas to consider the effects of the subbasin shape; moreover, four pollutant accumulation methods and the washoff equation for computing the water quality each time were used. According to the verification results, FFC-QUAL provides generally similar output as the measured data for the peak flow, total runoff volume, total loadings, peak concentration, and time of peak concentration for three rainfall events in the Gunja subbasin. In comparison with the ILLUDAS, SWMM, and MOUSE models, there is little difference between these models and the model developed in this study. The proposed model should be useful in urban watersheds because of its simplicity and its capacity to model common pollutants (e.g., biological oxygen demand, chemical oxygen demand, Escherichia coli, suspended solids, and total nitrogen and phosphorous) in runoff. The proposed model can also be used in design studies to determine how changes in infrastructure will affect the runoff and pollution loads. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

[Distribution characteristics and correlations of phosphorus in sediment and interstitial water of Nansi Lake, Shandong Province of East China in summer and winter].

PubMed

Li, Bao; Wang, Zhi-Qi; Wang, Qian-Suo; Cuan, Jing-Bo

2013-06-01

By using cylindrical sediment sampler and Peeper' s interstitial water sampler, the intact sediment and interstitial water were collected from different zones of Nansi Lake in Shandong Province in summer and winter. The distribution characteristics of the sediment phosphorus forms and of the phosphate (PO4(3-)-P) in interstitial water were analyzed, and their correlations were discussed. In the sediments of Nansi Lake, phosphorus was richer, and had a significant spatial differentiation, with an overall decreasing trend from north to south, which was related to the seriously polluted Northern Nansi Lake near Jining City. Among the phosphorous forms, inorganic phosphorus (IP) had the highest concentration, accounting for 52.3%-87.2% and 60.6%-88.3% of the total phosphorus (TP) in summer and winter, respectively. The TP concentrations in 5 cm surface sediment of four sub-lakes were all higher in summer than in winter, which could be related to the human activities such as exuberant aquaculture, more chemical fertilizers application around lake, and frequent tourism activities, etc. in summer. In vertical direction, the PO4(3-)-P concentration in interstitial water decreased after an initial increase in summer and winter, and was obviously higher in summer than in winter, suggesting that the phosphorous in sediment had a higher potential to release to the overlying water in summer. The organic phosphorus (OP) and IP in sediment had a significant correlation in summer but less correlation in winter, indicating that the transformation between sediment IP and OP was more active in summer than in winter. The iron and aluminum bound phosphorus (Fe/Al-P) and IP in sediment were significantly positively correlated with the PO4(3-)-P in interstitial water. In summer and winter, the average PO4(3-)-P concentration in interstitial water collected by Peeper' s interstitial water sampler was about 20%-50% higher than that collected by the conventional centrifugal method, suggesting that using Peeper' s interstitial water sampler could be more precise.

Parking Lot Runoff Quality and Treatment Efficiency of a Stormwater-Filtration Device, Madison, Wisconsin, 2005-07

USGS Publications Warehouse

Horwatich, Judy A.; Bannerman, Roger T.

2010-01-01

To evaluate the treatment efficiency of a stormwater-filtration device (SFD) for potential use at Wisconsin Department of Transportation (WisDOT) park-and-ride facilities, a SFD was installed at an employee parking lot in downtown Madison, Wisconsin. This type of parking lot was chosen for the test site because the constituent concentrations and particle-size distributions (PSDs) were expected to be similar to those of a typical park-and-ride lot operated by WisDOT. The objective of this particular installation was to reduce loads of total suspended solids (TSS) in stormwater runoff to Lake Monona. This study also was designed to provide a range of treatment efficiencies expected for a SFD. Samples from the inlet and outlet were analyzed for 33 organic and inorganic constituents, including 18 polycyclic aromatic hydrocarbons (PAHs). Samples were also analyzed for physical properties, including PSD. Water-quality samples were collected for 51 runoff events from November 2005 to August 2007. Samples from all runoff events were analyzed for concentrations of suspended sediment (SS). Samples from 31 runoff events were analyzed for 15 constituents, samples from 15 runoff events were analyzed for PAHs, and samples from 36 events were analyzed for PSD. The treatment efficiency of the SFD was calculated using the summation of loads (SOL) and the efficiency ratio methods. Constituents for which the concentrations and (or) loads were decreased by the SFD include TSS, SS, volatile suspended solids, total phosphorous (TP), total copper, total zinc, and PAHs. The efficiency ratios for these constituents are 45, 37, 38, 55, 22, 5, and 46 percent, respectively. The SOLs for these constituents are 32, 37, 28, 36, 23, 8, and 48 percent, respectively. The SOL for chloride was -21 and the efficiency ratio was -18. Six chemical constituents or properties-dissolved phosphorus, chemical oxygen demand, dissolved zinc, total dissolved solids, dissolved chemical oxygen demand, and dissolved copper-were not included in the efficiency or SOL, because the difference between concentrations in samples from the inlet and outlet were not significant. Concentrations of TP and TSS were inexplicably high in samples at the inlet for one event.

CONTRIBUTION OF NUTRIENTS AND E. COLI TO SURFACE WATER CONDITION IN THE OZARKS I. USING PARTIAL LEAST SQUARES PREDICTIONS WHEN STANDARD REGRESSION ASSUMPTIONS ARE VIOLATED

EPA Science Inventory

We present here the application of PLS regression to predicting surface water total phosphorous, total ammonia and Escherichia coli from landscape metrics. The amount of variability in surface water constituents explained by each model reflects the composition of the contributi...

Preparation of a YAG:Ce phosphor glass by screen-printing technology and its application in LED packaging.

PubMed

Yang, Liang; Chen, Mingxiang; Lv, Zhicheng; Wang, Simin; Liu, Xiaogang; Liu, Sheng

2013-07-01

A simple and practical method for preparing phosphor glass is proposed. Phosphor distribution and element analysis are investigated by optical microscope and field emission scanning electron microscope (FE-SEM). The phosphor particles dispersed in the matrix are vividly observed, and their distributions are uniform. Spectrum distribution and color coordinates dependent on the thickness of the screen-printed phosphor layer coupled with a blue light emitting diode (LED) chip are studied. The luminous efficacy of the 75 μm printed phosphor-layer phosphor glass packaged white LED is 81.24 lm/W at 350 mA. This study opens up many possibilities for applications using the phosphor glass on a selected chip in which emission is well absorbed by all phosphors. The screen-printing technique also offers possibilities for the design and engineering of complex phosphor layers on glass substrates. Phosphor screen-printing technology allows the realization of high stability and thermal conductivity for the phosphor layer. This phosphor glass method provides many possibilities for LED packing, including thin-film flip chip and remote phosphor technology.

GEOGRAPHIC TARGETING OF INCREASES IN NUTRIENT EXPORT DUE TO FUTURE URBANIZATION

EPA Science Inventory

Urbanization replaces the extant natural resource base (e.g., forests, wet- lands) with an infrastructure that is capable of supporting humans. One ecological consequence of urbanization is higher concentrations of nitrogen (N) and phosphorous (P) in streams, lakes, and estuaries...

ADSORPTION OF PHOSPHOROUS BY CATTAIL CALLUS CELLS

EPA Science Inventory

Data from this study demonstrates that cattail callus cells can be used to predict the phosphorus concentration in cattail leaves when they are supplied with similar phosphorus levels. If this relationship between callus cells and whole plants is found applicable to other marsh p...

Synthesis, characterization and luminescent properties of mixed phase bismuth molybdate-doped with Eu3+ ions

NASA Astrophysics Data System (ADS)

Wang, Liyong; Guo, Xiaoqing; Cai, Xiaomeng; Song, Qingwei; Han, Yuanyuan; Jia, Guang

2018-02-01

Red phosphors of Eu3+-doped bismuth molybdate (BMO) are prepared by a low temperature hydrothermal method assisting with Phenol Formaldehyde resin (PFr), and characterized by X-ray diffraction (XRD) patterns, Fourier transform infrared-spectroscopy (FT-IR), thermogravimetric analyzer (TGA), differential thermal analyzer (DTA), and photoluminescence (PL) spectroscopy. PL properties influence factors including molar ratio of Bi3+ and Mo3+ ions, PFr dosage and dopants concentration are discussed in detail. The results show that BMO can act as a useful host for Eu3+ ions doping, and energy transferring from Bi3+ to Eu3+ achieved efficiently, the BMO phosphors displayed intense red color emission under ultraviolet light excitation.

Fabrication and characterization of thin-film phosphor combinatorial libraries

NASA Astrophysics Data System (ADS)

Mordkovich, V. Z.; Jin, Zhengwu; Yamada, Y.; Fukumura, T.; Kawasaki, M.; Koinuma, H.

2002-05-01

The laser molecular beam epitaxy method was employed to fabricate thin-film combinatorial libraries of ZnO-based phosphors on different substrates. Fabrication of both pixel libraries, on the example of Fe-doped ZnO, and spread libraries, on the example of Eu-doped ZnO, has been demonstrated. Screening of the Fe-doped ZnO libraries led to the discovery of weak green cathodoluminescence with the maximum efficiency at the Fe content of 0.58 mol %. Screening of the Eu-doped ZnO libraries led to the discovery of unusual reddish-violet cathodoluminescence which is observed in a broad range of Eu concentration. No photoluminescence was registered in either system.

[Phosphoric acid ester preparations used in cattle, swine and sheep with special reference to cholinesterase activity. 4. Use of phosphoric acid esters and their effect on acetylcholinesterase activity in sheep].

PubMed

Mieth, K; Beier, D; Losch, K

1975-01-01

The use of organophosphorus preparations for the control of ectoparasites and endoparasites of sheep, particularly systemic application, is discussed. Experiments on 13 groups of sheep with five preparations produced in the German Democratic Republic in various formulations and concentrations showed that external application had good contact activity, but little was absorbed. Acetylcholinesterase activity was not inhibited, except by pour-on application of doses several times the normal dose. The preparations were arranged in order of cholinesterase inhibition. In contrast to cattle, diminished cholinesterase activity was unreliable as in indicator of systemic toxicity of organophosphorus preparations in sheep.

Incorporation of impurity to a tetragonal lysozyme crystal

NASA Astrophysics Data System (ADS)

Kurihara, Kazuo; Miyashita, Satoru; Sazaki, Gen; Nakada, Toshitaka; Durbin, Stephen D.; Komatsu, Hiroshi; Ohba, Tetsuhiko; Ohki, Kazuo

1999-01-01

Concentration of a phosphor-labeled impurity (ovalbumin) incorporated into protein (hen egg white lysozyme) crystals during growth was measured by fluorescence.This technique enabled us to measure the local impurity concentration in a crystal quantitatively. Impurity concentration increased with growth rate, which could not be explained by two conventional models (equilibrium adsorption model and Burton-Prim-Slichter model); a modified model is proposed. Impurity concentration also increased with the pH of the solution. This result is discussed considering the electrostatic interaction between the impurity and the crystallizing species.

Optimization of sintering conditions for cerium-doped yttrium aluminum garnet

NASA Astrophysics Data System (ADS)

Cranston, Robert Wesley McEachern

YAG:Ce phosphors have become widely used as blue/yellow light converters in camera projectors, white light emitting diodes (WLEDs) and general lighting applications. Many studies have been published on the production, characterization, and analysis of this optical ceramic but few have been done on determining optimal synthesis conditions. In this work, YAG:Ce phosphors were synthesized through solid state mixing and sintering. The synthesized powders and the highest quality commercially available powders were pressed and sintered to high densities and their photoluminescence (PL) intensity measured. The optimization process involved the sintering temperature, sintering time, annealing temperature and the level of Ce concentration. In addition to the PL intensity, samples were also characterized using particle size analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The PL data was compared with data produced from a YAG:Ce phosphor sample provided by Christie Digital. The peak intensities of the samples were converted to a relative percentage of this industry product. The highest value for the intensity of the commercial powder was measured for a Ce concentration of 0.3 mole% with a sintering temperature of 1540°C and a sintering dwell time of 7 hours. The optimal processing parameters for the in-house synthesized powder were slightly different from those of commercial powders. The optimal Ce concentration was 0.4 mole% Ce, sintering temperature was 1560°C and sintering dwell time was 10 hours. These optimal conditions produced a relative intensity of 94.20% and 95.28% for the in-house and commercial powders respectively. Polishing of these samples resulted in an increase of 5% in the PL intensity.

Solvent Extraction of Rare Earth Elements from a Nitric Acid Leach Solution of Apatite by Mixtures of Tributyl Phosphate and Di-(2-ethylhexyl) Phosphoric Acid

NASA Astrophysics Data System (ADS)

Ferdowsi, Ali; Yoozbashizadeh, Hossein

2017-12-01

Solvent extraction of rare earths from nitrate leach liquor of apatite using mixtures of tributyl phosphate (TBP) and di-(2-ethylhexyl) phosphoric acid (D2EHPA) was studied. The effects of nitrate and hydrogen ion concentration of the aqueous phase as well as the composition and concentration of extractants in the organic phase on the extraction behavior of lanthanum, cerium, neodymium, and yttrium were investigated. The distribution ratio of REEs increases by increasing the nitrate concentration in aqueous phase and concentration of extractants in organic phase, but the hydrogen ion concentration in aqueous phase has a decreasing effect. Yttrium as a heavy rare earth is more sensitive to these parameters than light rare earth elements. Although the composition of organic phase has a minor effect on the extraction of light rare earths, the percent of extraction of yttrium decreases dramatically by increasing the TBP content of organic phase. Mixtures of TBP and D2EHPA can show either synergism or antagonism extraction depending on the concentration and composition of extractants in organic phase. The best condition for separating rare earth elements in groups of heavy and light REEs can be achieved at high nitrate concentration, low H+ concentration, and high concentration of D2EHPA in organic phase. Separation of Ce and La by TBP and D2EHPA is practically impossible in the studied conditions; however, low nitrate concentration and high hydrogen ion concentration in aqueous phase and low concentration of extractants in organic phase favor the separation of Nd from other light rare earth elements.

Red phosphors for use in high CRI fluorescent lamps

DOEpatents

Srivastava, Alok; Comanzo, Holly; Manivannan, Vankatesan; Setlur, Anant Achyut

2005-11-15

Novel red emitting phosphors for use in fluorescent lamps resulting in superior color rendering index values compared to conventional red phosphors. Also disclosed is a fluorescent lamp including a phosphor layer comprising blends of one or more of a blue phosphor, a blue-green phosphor, a green phosphor and a red a phosphor selected from the group consisting of SrY.sub.2 O.sub.4 :Eu.sup.3+, (Y,Gd)Al.sub.3 B.sub.4 O.sub.12 :Eu.sup.3+, and [(Y.sub.1-x-y-m La.sub.y)Gd.sub.x ]BO.sub.3 :Eu.sub.m wherein y<0.50 and m=0.001-0.3. The phosphor layer can optionally include an additional deep red phosphor and a yellow emitting phosphor. The resulting lamp will exhibit a white light having a color rendering index of 90 or higher with a correlated color temperature of from 2500 to 10000 Kelvin. The use of the disclosed red phosphors in phosphor blends of lamps results in high CRI light sources with increased stability and acceptable lumen maintenance over the course of the lamp life.

Effect of belimbing wuluh (averrhoa bilimbi l.) extract gel exposure duration to surface roughness of enamel

NASA Astrophysics Data System (ADS)

Karima, F.; Eriwati, Y. K.; Triaminingsih, S.

2017-08-01

The purpose of this study was to analyze the effect of Belimbing Wuluh Gel Extract to surface roughness of enamel. Thirty-six premolars teeth that divided into 4 groups (n = 9), were exposed to 37% phosphoric acid gel (pH = 1) for 15 seconds as a control group, and belimbing wuluh extract gel with a concentration of 80% (pH = 1.8) for 15 seconds, 20 seconds, and 25 seconds as the treatment groups. The statistical analysis of paired and unpaired T-test shows that all treatment groups experienced a significant change (p <0.05). The greatest changes in surface roughness of enamel occurred after exposed by belimbing extract gel with an exposure duration of 25 seconds, but the roughness of 37% phosphoric acid gel is still greater. There was a correlation between roughness on the surface of tooth enamel with prolonged exposure belimbing wuluh extract gel with a concentration of 80%.

Study on luminescence characteristics of blue OLED with phosphor-doped host-guest structure

NASA Astrophysics Data System (ADS)

Wang, Zhen; Liu, Fei; Zheng, Xin; Chen, Ai; Xie, Jia-feng; Zhang, Wen-xia

2018-05-01

In this study, we design and fabricate phosphor-doped host-guest structure organic light-emitting diodes (OLEDs), where the blue-ray iridium complex electrophosphorescent material FIrpic acts as object material. Properties of the device can be accommodated by changing the host materials, dopant concentration and thickness of the light-emitting layer. The study shows that the host material N,N'-dicarbazolyl-3,5-benzene (mCP) has a higher triplet excited state energy level, which can effectively prevent FIrpic triplet excited state energy backtracking to host material, thus the luminous efficiency is improved. When mCP is selected as the host material, the thickness of the light-emitting layer is 30 nm and the dopant concentration is 8 wt%, the excitons can be effectively confined in the light-emitting region. As a result, the maximum current efficiency and the maximum brightness of the blue device can reach 15.5 cd/A and 7 196.3 cd/m2, respectively.

NIR emitting K2SrCl4:Eu2+, Nd3+ phosphor as a spectral converter for CIGS solar cell

NASA Astrophysics Data System (ADS)

Tawalare, P. K.; Bhatkar, V. B.; Omanwar, S. K.; Moharil, S. V.

2018-05-01

Intense near-infrared emitting phosphor K2SrCl4:Eu2+,Nd3+ with various concentrations of Nd3+ were synthesized. These are characterized with X-ray diffraction, reflectance, photoluminescence emission and photoluminescence excitation spectroscopy, PL lifetime measurements. The emission can be excited by a broad band in near ultra violet region as a consequence of Eu2+→Nd3+ energy transfer. The efficiency of Eu2+→Nd3+ energy transfer is as high as 95%. Fluorescence decay curves for Eu2+ doped samples are almost exponential and described by τ = 500 ns. Eu2+ lifetimes are shortened after Nd3+ doping. Near infrared Emission intensity is limited by Nd3+→Nd3+ energy transfer and the consequent concentration quenching. Nd3+ emission matches well with the spectral response of CIGS and CIS solar cells. Absorption of near ultra violet radiations followed by conversion to near infrared indicates the potential application in solar photovoltaics.

Blue emission in photoluminescence spectra of the red phosphor CaAlSiN3:Eu2+ at low Eu2+ concentration

NASA Astrophysics Data System (ADS)

Suda, Yoriko; Kamigaki, Yoshiaki; Yamamoto, Hajime

2018-04-01

In red phosphor CaAlSiN3:Eu2+, unintentional blue emission occurs with increasing intensity at low Eu2+ concentrations and also at low measurement temperatures. Time-resolved photoluminescence measurements were used to confirm the decrease in red emission and increase in blue emission with the decreasing Eu2+ concentration. The peak timing of blue emission occurred faster than that of red emission, and long lasting luminescence of red emission was observed as well as that of blue emission. The Eu2+ concentration dependences of the red and blue emissions were similar to those of the g values 4.75 (Eu2+) and 2.0025 (nitrogen vacancies), respectively, which were observed from electron spin resonance (ESR) measurements. The origin of the blue emission is proposed to be nitrogen vacancy defects, which had about the same ESR signal intensity as that of Eu2+ ions in CaAlSiN3:Eu2+ containing 0.01 at. % Eu2+. The possibility of red emission also arising from excited electron tunneling or thermal pathways via nitrogen vacancies is discussed. Long lasting red emission was observed, which is proposed to involve trapped electrons remaining at nitrogen vacancies, yielding blue emission and inducing red emission from Eu2+ ions.

Green emitting phosphors and blends thereof

DOEpatents

Setlur, Anant Achyut; Siclovan, Oltea Puica; Nammalwar, Prasanth Kumar; Sathyanarayan, Ramesh Rao; Porob, Digamber G.; Chandran, Ramachandran Gopi; Heward, William Jordan; Radkov, Emil Vergilov; Briel, Linda Jane Valyou

2010-12-28

Phosphor compositions, blends thereof and light emitting devices including white light emitting LED based devices, and backlights, based on such phosphor compositions. The devices include a light source and a phosphor material as described. Also disclosed are phosphor blends including such a phosphor and devices made therefrom.

Nanoporous anodic aluminum oxide with a long-range order and tunable cell sizes by phosphoric acid anodization on pre-patterned substrates

PubMed Central

Surawathanawises, Krissada; Cheng, Xuanhong

2014-01-01

Nanoporous anodic aluminum oxide (AAO) has been explored for various applications due to its regular cell arrangement and relatively easy fabrication processes. However, conventional two-step anodization based on self-organization only allows the fabrication of a few discrete cell sizes and formation of small domains of hexagonally packed pores. Recent efforts to pre-pattern aluminum followed with anodization significantly improve the regularity and available pore geometries in AAO, while systematic study of the anodization condition, especially the impact of acid composition on pore formation guided by nanoindentation is still lacking. In this work, we pre-patterned aluminium thin films using ordered monolayers of silica beads and formed porous AAO in a single-step anodization in phosphoric acid. Controllable cell sizes ranging from 280 nm to 760 nm were obtained, matching the diameters of the silica nanobead molds used. This range of cell size is significantly greater than what has been reported for AAO formed in phosphoric acid in the literature. In addition, the relationships between the acid concentration, cell size, pore size, anodization voltage and film growth rate were studied quantitatively. The results are consistent with the theory of oxide formation through an electrochemical reaction. Not only does this study provide useful operational conditions of nanoindentation induced anodization in phosphoric acid, it also generates significant information for fundamental understanding of AAO formation. PMID:24535886

Achieving High Luminescent Performance K2SiF6:Mn4+ Phosphor by Co-precipitation Process with Controlling the Reaction Temperature

NASA Astrophysics Data System (ADS)

Tran, Tat-Dat; Nguyen, Duy-Hung; Pham, Thanh-Huy; Nguyen, Duy-Cuong; Duong, Thanh-Tung

2018-05-01

K2SiF6:Mn4+ (KSF:Mn) phosphor was synthesized by the one-step co-precipitation process, at different temperatures. It was found that the reaction temperature played a key role in photoluminescence performance of the product. When the reaction temperature decreased from 0°C to - 20°C, the doping concentration, Mn/Si ratio, increased from 2% to 10%. However, further decrement of temperature (to - 30°C) reduced the Mn/Si ratio to 7%. The photo-luminescence (PL) intensity was maximized at the highest Mn/Si (10%), which corresponds to a reaction temperature of - 20°C. The KSF:Mn phosphor showed excellent luminescent properties at a wide range of temperatures (from room temperature to 470 K), especially after being dispersed in a polymer matrix. When combined with a commercial white light emitting diode (WLED), KSF:Mn significantly improved luminescent properties, such as color rendering index (CRI), correlated color temperature (CCT) and luminous efficiency. In particular, CRI increased from 67.3 to 87.4, while the CCT decreased from 7800 K to 3204 K. The luminous efficiency increased from 82.0 lm/W to 95.3 lm/W. The results indicated that the high quality KSF:Mn red phosphor could be achieved by a simple one-step co-precipitation method with a fine control of reaction temperature.

Energy transfer and color tunable emission in Tb3+,Eu3+ co-doped Sr3LaNa(PO4)3F phosphors.

PubMed

Li, Shuo; Guo, Ning; Liang, Qimeng; Ding, Yu; Zhou, Huitao; Ouyang, Ruizhuo; Lü, Wei

2018-02-05

A group of color tunable Sr 3 LaNa(PO 4 ) 3 F:Tb 3+ ,Eu 3+ phosphors were prepared by conventional high temperature solid state method. The phase structures, luminescence properties, fluorescence lifetimes and energy transfer were investigated in detail. Under 369nm excitation, owing to efficient energy transfer of Tb 3+ →Eu 3+ , the emission spectra both have green emission of Tb 3+ and red emission of Eu 3+ . An efficient energy transfer occur in Tb 3+ , Eu 3+ co-doped Sr 3 LaNa(PO 4 ) 3 F phosphors. The most possible mechanism of energy transfer is dipole-dipole interaction by Dexter's theoretical model. The energy transfer of Tb 3+ and Eu 3+ was confirmed by the variations of emission and excitation spectra and Tb 3+ /Eu 3+ decay lifetimes in Sr 3 LaNa(PO 4 ) 3 F:Tb 3+ ,Eu 3+ . The color tone can tuned from yellowish-green through yellow and eventually to reddish-orange with fixed Tb 3+ content by changing Eu 3+ concentrations. The results show that the prepared Tb 3+ , Eu 3+ co-doped color tunable Sr 3 LaNa(PO 4 ) 3 F phosphor can be used for white LED. Copyright © 2017 Elsevier B.V. All rights reserved.

Investigation of energy transfer in terbium doped Y 2SiO5 phosphor particles

NASA Astrophysics Data System (ADS)

Salis, M.; Carbonaro, C. M.; Corpino, R.; Anedda, A.; Ricci, P. C.

2012-07-01

The kinetics of luminescence of sol-gel synthesized terbium doped Y 2SiO5 (YSO) phosphor particles is investigated in detail with reference to Tb concentration in the 0.001%-10% range. By increasing the dopant concentration, the luminescence profile changes from a blue to a green peaked emission spectrum because of the energy transfer among centers. The inter-center energy transfer mechanism is well accounted for by the Inokuti-Hirayama (IH) kinetic model which is based on a statistical average of inter-center distance dependent decay modes of the donor luminescence. The distribution of the decay modes is implemented from the Förster-Dexter resonance theory of energy transfer by assuming a rate constant for the energy transfer by multipolar interactions between donors and acceptors. However, the experimental results recorded in the low concentration limit show the presence of green emission contributions in the luminescence spectrum which cannot be related to the Tb concentration; for this reason an additional internal energy transfer mechanism, occurring among levels of the same center, is proposed to account for the recorded emission properties. Thus, a new and more exhaustive model which includes both the internal and external energy transfer processes is considered; the proposed model allows a better explanation of the spectroscopic features of Tb related centers in YSO crystals and discloses the critical concentration and the quantum yields of the different energy transfer mechanisms.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tong, Tao; Letoquin, Ronan; Keller, Bernd

An LED lamp or bulb is disclosed that comprises a light source, a heat sink structure and a remote planar phosphor carrier having at least one conversion material. The phosphor carrier can be remote to the light sources and mounted to the heat sink so that heat from the phosphor carrier spreads into the heat sink. The phosphor carrier can comprise a thermally conductive transparent material and a phosphor layer, with an LED based light source mounted to the heat sink such that light from the light source passes through the phosphor carrier. At least some of the LED lightmore » is converted by the phosphor carrier, with some lamp embodiments emitting a white light combination of LED and phosphor light. The phosphor arranged according to the present invention can operate at lower temperature to thereby operate at greater phosphor conversion efficiency and with reduced heat related damage to the phosphor.« less

Role of Gd{sup 3+} ion on downshifting and upconversion emission properties of Pr{sup 3+}, Yb{sup 3+} co-doped YNbO{sub 4} phosphor and sensitization effect of Bi{sup 3+} ion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dwivedi, A.; Rai, S. B., E-mail: sbrai49@yahoo.co.in; Mishra, Kavita

Dual-mode luminescence (downshifting-DS and upconversion-UC) properties of Pr{sup 3+}/Yb{sup 3+} co-doped Y{sub 1−x}Gd{sub x}NbO{sub 4} (x = 0.0, 0.5, and 1.0) phosphors synthesized by solid state reaction technique have been explored with and without Gd{sup 3+} ion. The structural characterizations (XRD, SEM, and FTIR) confirm the pure phase of YNbO{sub 4} phosphor. Further, with the Gd{sup 3+} ion co-doping, the YNbO{sub 4} phosphors having a random shape and the large particle size are found to be transformed into nearly spherical shape particles with the reduced particle size. The optical band gaps (E{sub g}) of Y{sub 1−x}Gd{sub x}NbO{sub 4} (x = 0.00, 0.25, 0.50, andmore » 1.00) calculated from UV-Vis-NIR measurements are ∼3.69, 4.00, 4.38, and 4.44 eV, respectively. Moreover, YNbO{sub 4} phosphor is a promising blue emitting material, whereas Y{sub 1−x−y−z}Pr{sub y}Yb{sub z}Gd{sub x}NbO{sub 4} phosphor gives intense green, blue, and red emissions via dual-mode optical processes. The broad blue emission arises due to (NbO{sub 4}){sup 3−} group of the host with λ{sub ex} = 264 nm, whereas Pr{sup 3+} doped YNbO{sub 4} phosphor gives dominant red and blue emissions along with comparatively weak green emission on excitation with λ{sub ex} = 300 nm and 491 nm. The concentration dependent variation in emission intensity at 491 nm ({sup 3}P{sub 0}→{sup 3}H{sub 4} transition) and 612 nm ({sup 1}D{sub 2}→{sup 3}H{sub 4} transition); at 612 nm ({sup 1}D{sub 2}→{sup 3}H{sub 4} transition) and 658 nm ({sup 3}P{sub 0}→{sup 3}F{sub 2} transition) of Pr{sup 3+} ion in YNbO{sub 4} phosphor with λ{sub ex} = 300 nm and 491 nm excitations, respectively, has been thoroughly explored and explained by the cross-relaxation process through different channels. The sensitization effect of Bi{sup 3+} ion co-doping on DS properties of the phosphor has also been studied. The observed DS results have been optimized by varying the concentration of Pr{sup 3+} and Bi{sup 3+} ions, and the results are explained by the well-known simple band structure model. The study of Gd{sup 3+} co-doping reveals noticeable differences in DS characteristics of Y{sub 1−x}Pr{sub x}NbO{sub 4} phosphors: the overall decrement and increment (except for 612 nm emission) in intensity of DS emission on excitation with λ{sub ex} = 264 nm and 491 nm, respectively. These observations have been thoroughly explained, and the {sup 1}D{sub 2}→{sup 3}H{sub 4} transition (612 nm) of Pr{sup 3+} ion is found to be strongly dependent on surrounding environment of the host matrix. The UC properties of Y{sub 0.95−x}Pr{sub x}Yb{sub 0.05}NbO{sub 4} phosphors have been explored using Near Infra-Red (NIR) excitation. The material gives intense green and relatively weak blue and red UC emissions with λ{sub ex} = 980 nm. Interestingly, the UC emission intensity is further enhanced in the case of Y{sub 0.949−x}Pr{sub 0.001}Yb{sub 0.05}Gd{sub x}NbO{sub 4} phosphors. In addition, the less explored laser induced heating effect with the pump power as well as the irradiation time on the UC emission has been explored in Y{sub 0.949−x}Pr{sub 0.001}Yb{sub 0.05}Gd{sub x}NbO{sub 4} (x = 0, 0.5, and 0.949) phosphor samples, and subsequently, this feature has been found to be superior for Gd{sub 0.949}Pr{sub 0.001}Yb{sub 0.05}NbO{sub 4} phosphor. The comparative study between the two hosts, viz., YNbO{sub 4} and GdNbO{sub 4} shows that GdNbO{sub 4} is better than YNbO{sub 4} for UC emission behavior; however, a reverse is observed as for as DS behavior is concerned only for the particular excitation wavelength (λ{sub ex} = 264 nm).« less

Structural and photoluminescence properties of stannate based displaced pyrochlore-type red phosphors: Ca(3-x)Sn₃Nb₂O₁₄:xEu³⁺.

PubMed

Sreena, T S; Prabhakar Rao, P; Francis, T Linda; Raj, Athira K V; Babu, Parvathi S

2015-05-14

New stannate based displaced pyrochlore-type red phosphors, Ca(3-x)Sn3Nb2O14:xEu(3+), were prepared via a conventional solid state method. The influence of partial occupancy of Sn in both A and B sites of the pyrochlore-type oxides on the photoluminescence properties was studied using powder X-ray diffraction, FT-Raman, transmission electron microscopy, scanning electron microscopy with energy dispersive spectrometry, UV-visible absorption spectroscopy, and photoluminescence excitation and emission spectra with lifetime measurements. The structural analysis establishes that these oxides belong to a cubic displaced pyrochlore type structure with a space group Fd3̄m. These phosphors exhibit strong absorptions at near UV and blue wavelength regions and emit intense multiband emissions due to Eu(3+ 5)D0-(7)F(0, 1, 2) transitions. The absence of characteristic MD transition splitting points out that local cation disorder exists in this type of displaced pyrochlores, reducing the D(3d) inversion symmetry, which is not evidenced by such disorder in the X-ray diffraction analysis. The unusual forbidden intense sharp (5)D0-(7)F0 transition indicates single site occupancy of Eu(3+) with a narrower range of bonding environment, preventing the cluster formation. This is supported by the stable (5)D0 lifetime with Eu(3+) concentration. The Judd-Ofelt intensity parameter assessment corroborates these results. The CIE color coordinates of these phosphors were found to be (0.60, 0.40), which are close to the NTSC standard values (0.67, 0.33) for a potential red phosphor.

Effect of rare earth doping on optical and spectroscopic characteristics of BaZrO3:Eu3+,Tb3+ perovskites.

PubMed

Katyayan, Shambhavi; Agrawal, Sadhana

2018-04-04

This paper reports structural investigations of rare earth doped BaZrO 3 phosphors synthesized by Solid state reaction technique with varying concentrations of Eu 3+ and Tb 3+ from 0 mol% to 2 mol%. The synthesized phosphors show enhanced variable emissions in the visible region corresponding to different hypersensitive electronic transitions of Eu 3+ and Tb 3+ ions. With cubic structure confirmed in XRD analysis, the FESEM images show uniform grain connectivity and homogeneity of prepared samples. The TEM micrographs of the synthesized phosphors show agglomerated irregular structures. The synthesized phosphors were also subjected to FTIR, Raman, EDXS analysis along with studies of thermoluminescent and photoluminescent characteristics. On subjecting to 229 nm (UV) excitation, the phosphors show enhanced PL emissions corresponding to 571 nm ( 5 D 0 - 7 F 0 ), 591 nm ( 5 D 0 - 7 F 1 ), 615 nm ( 5 D 0 - 7 F 2 ) and 678 nm ( 5 D 0 - 7 F 4 ) hypersensitive transitions of Eu 3+ ions and emission peaks at 489 nm ( 5 D 4 - 7 F 6 ), 539 nm ( 5 D 4 - 7 F 5 ), 589 nm ( 5 D 4 - 7 F 4 ) and 632 nm ( 5 D 4 - 7 F 3 ) accounting for electronic transitions of Tb 3+ ions respectively. The computed average PL lifetime is 14.014 s. In the TL analysis, the second order of kinetics with the activation energy varying from 5.0 × 10 -1 eV to 6.6 × 10 -1 eV is reported. The maximum TL lifetime is estimated as 19.4985 min in the TL lifetime analysis.

Effect of rare earth doping on optical and spectroscopic characteristics of BaZrO3:Eu3+,Tb3+ perovskites

NASA Astrophysics Data System (ADS)

Katyayan, Shambhavi; Agrawal, Sadhana

2018-06-01

This paper reports structural investigations of rare earth doped BaZrO3 phosphors synthesized by Solid state reaction technique with varying concentrations of Eu3+ and Tb3+ from 0 mol% to 2 mol%. The synthesized phosphors show enhanced variable emissions in the visible region corresponding to different hypersensitive electronic transitions of Eu3+ and Tb3+ ions. With cubic structure confirmed in XRD analysis, the FESEM images show uniform grain connectivity and homogeneity of prepared samples. The TEM micrographs of the synthesized phosphors show agglomerated irregular structures. The synthesized phosphors were also subjected to FTIR, Raman, EDXS analysis along with studies of thermoluminescent and photoluminescent characteristics. On subjecting to 229 nm (UV) excitation, the phosphors show enhanced PL emissions corresponding to 571 nm (5D0-7F0), 591 nm (5D0-7F1), 615 nm (5D0-7F2) and 678 nm (5D0-7F4) hypersensitive transitions of Eu3+ ions and emission peaks at 489 nm (5D4-7F6), 539 nm (5D4-7F5), 589 nm (5D4-7F4) and 632 nm (5D4-7F3) accounting for electronic transitions of Tb3+ ions respectively. The computed average PL lifetime is 14.014 s. In the TL analysis, the second order of kinetics with the activation energy varying from 5.0 × 10‑1 eV to 6.6 × 10‑1 eV is reported. The maximum TL lifetime is estimated as 19.4985 min in the TL lifetime analysis.

Formation of titanium phosphate composites during phosphoric acid decomposition of natural sphene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maslova, Marina V.; Rusanova, Daniela; Naydenov, Valeri

2008-12-15

Decomposition of mineral sphene, CaTiOSiO{sub 4}, by H{sub 3}PO{sub 4} is investigated in detail. During the dissolution process, simultaneous calcium leaching and formation of titanium phosphate (TiP) take place. The main product of decomposition is a solid titanium phosphate-silica composite. The XRD, solid-sate NMR, IR, TGA, SEM and BET data were used to identify and characterize the composite as a mixture of crystalline Ti(HPO{sub 4}){sub 2}.H{sub 2}O and silica. When 80% phosphoric acid is used the decomposition degree is higher than 98% and calcium is completely transferred into the liquid phase. Formation of Ti(HPO{sub 4}){sub 2}.H{sub 2}O proceeds via formationmore » of meta-stable titanium phosphate phases, Ti(H{sub 2}PO{sub 4})(PO{sub 4}).2H{sub 2}O and Ti(H{sub 2}PO{sub 4})(PO{sub 4}). The sorption affinities of TiP composites were examined in relation to caesium and strontium ions. A decrease of H{sub 3}PO{sub 4} concentration leads to formation of composites with greater sorption properties. The maximum sorption capacity of TiP is observed when 60% H{sub 3}PO{sub 4} is used in sphene decomposition. The work demonstrates a valuable option within the Ti(HPO{sub 4}){sub 2}.H{sub 2}O-SiO{sub 2} composite synthesis scheme, to use phosphoric acid flows for isolation of CaHPO{sub 4}.2H{sub 2}O fertilizer. - Graphical abstract: A new synthesis scheme for preparation of composite titanium phosphate (TiP) ion-exchangers upon one-stage decomposition process of natural sphene with phosphoric acid is presented. Syntheses of {alpha}-TiP-silica composites proceed via formation of meta-stable titanium phosphate phases. The concentration of H{sub 3}PO{sub 4} determines the porosity of final products and their sorption affinities.« less

A novel single-phase white phosphor NaBaBO{sub 3}:Dy{sup 3+},K{sup +} for near-UV white light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Jianghui; Cheng, Qijin; Wu, Jieyang

Highlights: • A white phosphor NaBaBO{sub 3}:Dy{sup 3+},K{sup +} with CIE coordinate (0.301, 0.308) was synthesized. • The optimum doping concentration of Dy{sup 3+} ions was found. • The effect and mechanism of K{sup +} ion as a charge compensator were discussed. • Temperature-dependent PL property of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} was studied. • PL decay and quantum efficiency behaviors of the samples were investigated. - Abstract: A novel Dy{sup 3+}-doped NaBaBO{sub 3} white-emitting phosphor has been prepared by high temperature solid-state reaction method. The phase structure and luminescence properties of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} samples were investigated. Photoluminescence resultsmore » show that the as-prepared samples could be effectively excited by near-ultraviolet (NUV) light and generate white light emission due to the {sup 4}F{sub 9/2} → {sup 6}H{sub 15/2} (blue) transition and {sup 4}F{sub 9/2} → {sup 6}H{sub 13/2} (yellow) transition of Dy{sup 3+} ions, respectively. The optimum doping concentration of Dy{sup 3+} ions in the NaBaBO{sub 3} host was determined to be 5.0 mol% and the CIE chromaticity of the sample was determined to be (0.301, 0.308). Moreover, the mechanism of K{sup +} ion as a charge compensator on the improvement of photoluminescence property and the effect of temperature on the photoluminescence property of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} were investigated. Furthermore, photoluminescence decay and quantum efficiency behaviors of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} were also studied. The present work demonstrates that the NaBaBO{sub 3}:Dy{sup 3+},K{sup +} phosphor is a potential candidate for NUV white light emitting diodes.« less

Toward scatter-free phosphors in white phosphor-converted light-emitting diodes

PubMed Central

Park, Hoo Keun; Oh, Ji Hye; Rag Do, Young

2012-01-01

Scatter-free phosphors promise to suppress the scattering loss of conventional micro-size powder phosphors in white phosphor-converted light-emitting diodes (pc-LEDs). Large micro-size cube phosphors (~100 μm) are newly designed and prepared as scatter-free phosphors, combining the two scatter-free conditions of particles based on Mie’s scattering theory; the grain size or grain boundary was smaller than 50 nm and the particle size was larger than 30 μm. A careful evaluation of the conversion efficiency and packaging efficiency of the large micro-size cube phosphor-based white pc-LED demonstrated that large micro-size cube phosphors are an outstanding potential candidate for scatter-free phosphors in white pc-LEDs. The luminous efficacy and packaging efficiency of the Y3Al5O12:Ce3+ large micro-size cube phosphor-based pc-LEDs were 123.0 lm/W and 0.87 at 4300 K under 300 mA, which are 17% and 34% higher than those of commercial powder phosphor-based white LEDs (104.8 lm/W and 0.65), respectively. In addition, the introduction of large micro-size cube phosphors can reduce the wide variation in optical properties as a function of both the ambient temperature and applied current compared with those of conventional powder phosphor-based white LEDs. PMID:22535113

γδT Cells Exacerbate Podocyte Injury via the CD28/B7-1-Phosphor-SRC Kinase Pathway

PubMed Central

Chen, Wanbing; Zhang, Gaofu; Wang, Mo; Yang, Haiping

2018-01-01

Primary nephrotic syndrome (PNS) is a devastating pediatric disorder. However, its mechanism remains unclear. Previous studies detected B7-1 in podocytes; meanwhile, γδT cells play pivotal roles in immune diseases. Therefore, this study aimed to assess whether and how γδT cells impact podocytes via the CD28/B7-1 pathway. WT and TCRδ−/− mice were assessed. LPS was used to induce nephropathy. Total γδT and CD28+γδT cells were quantitated in mouse spleen and kidney samples. B7-1 and phosphor-SRC levels in the kidney were detected as well. In vitro, γδT cells from the mouse spleen were cocultured with mouse podocytes, and apoptosis rate and phosphor-SRC expression in podocytes were assessed. Compared with control mice, WT mice with LPS nephropathy showed increased amounts of γδT cells in the kidney. Kidney injury was alleviated in TCRδ−/− mice. Meanwhile, B7-1 and phosphor-SRC levels were increased in the kidney from WT mice with LPS nephropathy. CD28+γδT cells were decreased, indicating CD28 may play a role in LPS nephropathy. Immunofluorescence colocalization analysis revealed a tight association of γδT cells with B7-1 in the kidney. High B7-1 expression was detected in podocytes treated with LPS. Podocytes cocultured with γδT cells showed higher phosphor-SRC and apoptosis rate than other cell groups. Furthermore, CD28/B7-1 blockage with CTLA4-Ig in vitro relieved podocyte injury. γδT cells exacerbate podocyte injury via CD28/B7-1 signaling, with downstream involvement of phosphor-SRC. The CD28/B7-1 blocker CTLA4-Ig prevented progressive podocyte injury, providing a potential therapeutic tool for PNS. PMID:29862277

Evaluation and Comparison of High-Resolution (HR) and High-Light (HL) Phosphors in the Micro-Angiographic Fluoroscope (MAF) using Generalized Linear Systems Analyses (GMTF, GDQE) that include the Effect of Scatter, Magnification and Detector Characteristics.

PubMed

Gupta, Sandesh K; Jain, Amit; Bednarek, Daniel R; Rudin, Stephen

2011-01-01

In this study, we evaluated the imaging characteristics of the high-resolution, high-sensitivity micro-angiographic fluoroscope (MAF) with 35-micron pixel-pitch when used with different commercially-available 300 micron thick phosphors: the high resolution (HR) and high light (HL) from Hamamatsu. The purpose of this evaluation was to see if the HL phosphor with its higher screen efficiency could be replaced with the HR phosphor to achieve improved resolution without an increase in noise resulting from the HR's decreased light-photon yield. We designated the detectors MAF-HR and MAF-HL and compared them with a standard flat panel detector (FPD) (194 micron pixel pitch and 600 micron thick CsI(Tl)). For this comparison, we used the generalized linear-system metrics of GMTF, GNNPS and GDQE which are more realistic measures of total system performance since they include the effect of scattered radiation, focal spot distribution, and geometric un-sharpness. Magnifications (1.05-1.15) and scatter fractions (0.28 and 0.33) characteristic of a standard head phantom were used. The MAF-HR performed significantly better than the MAF-HL at high spatial frequencies. The ratio of GMTF and GDQE of the MAF-HR compared to the MAF-HL at 3(6) cycles/mm was 1.45(2.42) and 1.23(2.89), respectively. Despite significant degradation by inclusion of scatter and object magnification, both MAF-HR and MAF-HL provide superior performance over the FPD at higher spatial frequencies with similar performance up to the FPD's Nyquist frequency of 2.5 cycles/mm. Both substantially higher resolution and improved GDQE can be achieved with the MAF using the HR phosphor instead of the HL phosphor.

Effects of melamine formaldehyde resin and CaCO3 diffuser-loaded encapsulation on correlated color temperature uniformity of phosphor-converted LEDs.

PubMed

Yang, Liang; Lv, Zhicheng; Jiaojiao, Yuan; Liu, Sheng

2013-08-01

Phosphor-free dispensing is the most widely used LED packaging method, but this method results in poor quality in angular CCT uniformity. This study proposes a diffuser-loaded encapsulation to solve the problem; the effects of melamine formaldehyde (MF) resin and CaCO3 loaded encapsulation on correlated color temperature (CCT) uniformity and luminous efficiency reduction of the phosphor-converted LEDs are investigated. Results reveal that MF resin loaded encapsulation has better light diffusion performance compared to MF resin loaded encapsulation at the same diffuser concentration, but CaCO3 loaded encapsulation has better luminous efficiency maintenance. The improvements in angular color uniformity for the LEDs emitting with MF resin and CaCO3 loaded encapsulation can be explained by the increase in photon scattering. The utility of this low cost and controllable mineral diffuser packaging method provides a practical approach for enhancing the angular color uniformity of LEDs. The diffuser mass ratio of 1% MF resin or 10% CaCO3 is the optimum condition to obtain low angular CCT variance and high luminous efficiency.

High quantum yield of the Egyptian blue family of infrared phosphors (MCuSi4O10, M = Ca, Sr, Ba)

NASA Astrophysics Data System (ADS)

Berdahl, Paul; Boocock, Simon K.; Chan, George C.-Y.; Chen, Sharon S.; Levinson, Ronnen M.; Zalich, Michael A.

2018-05-01

The alkaline earth copper tetra-silicates, blue pigments, are interesting infrared phosphors. The Ca, Sr, and Ba variants fluoresce in the near-infrared (NIR) at 909, 914, and 948 nm, respectively, with spectral widths on the order of 120 nm. The highest quantum yield ϕ reported thus far is ca. 10%. We use temperature measurements in sunlight to determine this parameter. The yield depends on the pigment loading (mass per unit area) ω with values approaching 100% as ω → 0 for the Ca and Sr variants. Although maximum quantum yield occurs near ω = 0, maximum fluorescence occurs near ω = 70 g m-2, at which ϕ = 0.7. The better samples show fluorescence decay times in the range of 130 to 160 μs. The absorbing impurity CuO is often present. Good phosphor performance requires long fluorescence decay times and very low levels of parasitic absorption. The strong fluorescence enhances prospects for energy applications such as cooling of sunlit surfaces (to reduce air conditioning requirements) and luminescent solar concentrators.

Optimization of preparation of activated carbon from cotton stalk by microwave assisted phosphoric acid-chemical activation.

PubMed

Deng, Hui; Zhang, Genlin; Xu, Xiaolin; Tao, Guanghui; Dai, Jiulei

2010-10-15

The preparation of activated carbon (AC) from cotton stalk was investigated in this paper. Orthogonal array experimental design method was used to optimize the preparation of AC using microwave assisted phosphoric acid. Optimized parameters were radiation power of 400 W, radiation time of 8 min, concentration of phosphoric acid of 50% by volume and impregnation time of 20 h, respectively. The surface characteristics of the AC prepared under optimized condition were examined by pore structure analysis, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR). Pore structure analysis shows that mecropores constitute more of the porosity of the prepared AC. Compared to cotton stalk, different functionalities and morphology on the carbon surfaces were formed in the prepared process. The adsorption capacity of the AC was also investigated by removing methylene blue (MB) in aqueous solution. The equilibrium data of the adsorption was well fitted to the Langmuir isotherm. The maximum adsorption capacity of MB on the prepared AC is 245.70 mg/g. The adsorption process follows the pseudo-second-order kinetic model. 2010 Elsevier B.V. All rights reserved.

X-ray absorption spectroscopy and photoluminescence study of rare earth ions doped strontium sulphide phosphors

NASA Astrophysics Data System (ADS)

Vij, Ankush; Gautam, Sanjeev; Kumar, Vinay; Brajpuriya, R.; Kumar, Ravi; Singh, Nafa; Chae, Keun Hwa

2013-01-01

We present here the electronic structure and photoluminescence properties of Sm (0.1-1.0 mol%) doped SrS phosphors. The doping in SrS was probed by near-edge X-ray absorption fine structure (NEXAFS) at M5,4-edges of Sm in total electron yield mode. The simulated absorption edges using atomic multiplet calculations were correlated with experimental results, which clearly reveal the presence of trivalent state of Sm in SrS matrix. However, for Sm (1 mol%), very minor traces of Sm2+ were also observed, which have been explained by comparing the NEXAFS spectra in total electron and florescence yield mode. The PL emission of SrS:Sm comprises of three sharp bands at 567, 602 and 650 nm owing to the well-known intra 4f transitions from 4G5/2 to 6HJ (J = 5/2, 7/2, 9/2) levels of Sm3+ ions in SrS host. The effect of Ce co-doping on SrS:Sm phosphors was also investigated, which exhibits characteristic PL emission of independent ions at their respective excitation wavelengths. However, at an excitation wavelength of 393 nm, SrS:Ce,Sm exhibits the simultaneous characteristic PL emission of both ions spanning into blue-green-red region. The CIE chromaticity coordinates also clearly show the influence of excitation wavelengths on the emission colour of SrS:Ce,Sm.

Investigation of Upconversion, downshifting and quantum –cutting behavior of Eu3+, Yb3+, Bi3+ co-doped LaNbO4 phosphor as a spectral conversion material

NASA Astrophysics Data System (ADS)

Dwivedi, A.; Mishra, K.; Rai, S. B.

2018-06-01

This work presents the spectral conversion characteristics [upconversion (UC), downshifting (DS) and quantum–cutting (QC) optical processes] of Eu3+, Yb3+ and Bi3+ co-doped LaNbO4 (LBO) phosphor samples synthesized by solid state reaction technique. The crystal structure and the pure phase formation have been confirmed by x-ray diffraction (XRD) measurements. The surface morphology and particle size are studied by scanning electron microscopy (SEM). The rarely observed intense red UC emission from Eu3+ ion has been successfully obtained in Eu3+/Yb3+ co-doped LaNbO4 phosphor (on excitation with 980 nm) by optimizing the concentrations of Eu3+ and Yb3+ ions. The downshifting (DS) behavior has been studied by photoluminescence (PL) measurements on excitation with 265 nm wavelength from a Xe lamp source. A broad blue emission in the region 300–550 nm with its maximum ∼415 nm due to charge transfer band (CTB) of the host and large number of sharp peaks due to f-f transitions of Eu3+ ion have been observed. The energy transfer has been observed from (NbO4)3‑ to Eu3+ ion and the fluorescence emission has been optimized by varying the concentration of Eu3+ ion. An intense red emission has also been observed corresponding to 5D0 → 7F2 transition of Eu3+ ion at 611 nm in LBO: 0.09Eu3+ phosphor on excitation with 394 nm. The luminescence properties of Eu3+ ion are enhanced further through the sensitization effect of Bi3+ ion. The near infra-red (NIR) quantum cutting (QC) behavior due to Yb3+ ion has been monitored on excitation with 265 as well as 394 nm. The NIR QC is observed due to 2F5/2 → 2F7/2 transition of Yb3+ ion via co-operative energy transfer (CET) process from (NbO4)3‑ as well as Eu3+ ions to Yb3+ ion. This multimodal behavior (UC, DS and QC) makes this a promising phosphor material for multi-purpose spectral converter.

Luminescence properties of ZrW{sub 2}O{sub 8}:Eu{sup 3+} nanophosphors for white light emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, Jinsheng, E-mail: jsliao1209@126.com; Liu, Shaohua; Wen, He-Rui

2015-10-15

Highlights: • Eu{sup 3+} ions occupy C{sub 1} point group of the Zr{sup 4+} site in ZrW{sub 2}O{sub 8} crystals. • The optimum doping concentration of Eu{sup 3+} was determined for the red emission. • ZrW{sub 2}O{sub 8}:Eu possess high quantum efficiency and suitable chromaticity coordinates. - Abstract: ZrW{sub 2}O{sub 8}:Eu{sup 3+} nanophosphors (ca. 60 nm) with different Eu{sup 3+} doping concentrations were obtained using hydrothermal syntheses. X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), photoluminescence excitation and emission spectra as well as decay curve measurements were used for the characterization. Under 466 nm excitation, strong redmore » emission at 616 nm corresponding to {sup 5}D{sub 0}–{sup 7}F{sub 2} transition of Eu{sup 3+} was observed for ZrW{sub 2}O{sub 8}:Eu{sup 3+} (9 mol%) phosphors. The values of intensity parameter Ω{sub 2} and Ω{sub 4} are 17.82 × 10{sup −20} cm{sup 2} and 1.092 × 10{sup −20} cm{sup 2}, respectively. The high quantum efficiency of 83.5% of the ZrW{sub 2}O{sub 8}:Eu{sup 3+} (9 mol%) suggests this material could be promising red phosphor for generating white light in phosphor-converted white light-emitting diodes (LED)« less

Shape tailored green synthesis of CeO2:Ho3+ nanopowders, its structural, photoluminescence and gamma radiation sensing properties

NASA Astrophysics Data System (ADS)

Malleshappa, J.; Nagabhushana, H.; Kavyashree, D.; Prashantha, S. C.; Sharma, S. C.; Premkumar, H. B.; Shivakumara, C.

2015-06-01

CeO2:Ho3+ (1-9 mol%) nanopowders have been prepared by efficient and environmental friendly green combustion method using Aloe vera gel as fuel for the first time. The final products are well characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), fourier transform infrared (FTIR). Bell, urchin, core shell and flower like morphologies are observed with different concentrations of the A. vera gel. It is apparent that by adjusting the concentration of the gel, considerable changes in the formation of CeO2:Ho3+ nano structures can be achieved. Photoluminescence (PL) studies show green (543, 548 nm) and red (645, 732 nm) emissions upon excited at 400 nm wavelength. The emission peaks at ∼526, 548, 655 and 732 nm are associated with the transitions of 5F3 → 5I8, 5S2 → 5I8, 5F5 → 5I8 and 5S2 → 5I7, respectively. Three TL glow peaks are observed at 118, 267 and 204 °C for all the γ irradiated samples which specify the surface and deeper traps. Linear TL response in the range 0.1-2 kGy shows that phosphor is fairly useful as γ radiation dosimeter. Kinetic parameters associated with the glow peaks are estimated using Chen's half width method. The CIE coordinate values show that phosphor is quite useful for the possible applications in WLEDs as orange red phosphor.

Source-specific sewage pollution detection in urban river waters using pharmaceuticals and personal care products as molecular indicators.

PubMed

Kiguchi, Osamu; Sato, Go; Kobayashi, Takashi

2016-11-01

Source-specific elucidation of domestic sewage pollution caused by various effluent sources in an urban river water, as conducted for this study, demands knowledge of the relation between concentrations of pharmaceuticals and personal care products (PPCPs) as molecular indicators (caffeine, carbamazepine, triclosan) and water quality concentrations of total nitrogen (T-N) and total phosphorous (T-P). River water and wastewater samples from the Asahikawa River Basin in northern Japan were analyzed using derivatization-gas chromatography/mass spectrometry. Caffeine, used as an indicator of domestic sewage in the Asahikawa River Basin, was more ubiquitous than either carbamazepine or triclosan (92-100 %). Its concentration was higher than any target compound used to assess the basin: <4.4-370 ng/L for caffeine, <0.6-3.9 ng/L for carbamazepine, and <1.1-13 ng/L for triclosan. Higher caffeine concentrations detected in wastewater effluents and the strongly positive mutual linear correlation between caffeine and T-N or T-P (R 2  > 0.759) reflect the contribution of septic tank system effluents to the lower Asahikawa River Basin. Results of relative molecular indicators in combination with different molecular indicators (caffeine/carbamazepine and triclosan/carbamazepine) and cluster analysis better reflect the contribution of sewage than results obtained using concentrations of respective molecular indicators and cluster analysis. Relative molecular indicators used with water quality parameters (e.g., caffeine/T-N ratio) in this study provide results more clearly, relatively, and quantitatively than results obtained using molecular indicators alone. Moreover, the caffeine/T-N ratio reflects variations of caffeine flux from effluent sources. These results suggest strongly relative molecular indicators are also useful indicators, reflecting differences in spatial contributions of domestic sources for PPCPs in urban areas.

Sources of nitrogen and phosphorous to northern San Francisco Bay

USGS Publications Warehouse

Hager, Stephen W.; Schemel, Laurence E.

1992-01-01

We studied nutrient sources to the Sacramento River and Suisun Bay (northern San Francisco Bay) and the influence which these sources have on the distributions of dissolved inorganic nitrogen (DIN) and dissolved reactive phosphorus (DRP) in the river and bay. We found that agricultural return flow drains and a municipal wastewater treatment plant were the largest sources of nutrients to the river during low river flow. The Sutter and Colusa agricultural drains contributed about 70% of the transport of DIN and DRP by the river above Sacramento (about 20% of the total transport by the river) between August 8 and September 26, 1985. Further downstream, the Sacramento Regional Wastewater Treatment Plant discharged DIN and DRP at rates that were roughly 70% of total DIN and DRP transport by the river at that time. Concentrations at Rio Vista on the tidal river below the Sacramento plant and at the head of the estuary were related to the reciprocals of the river flows, indicating the importance of dilution of the Sacramento waste by river flows. During very dry years, elevated DIN and DRP concentrations were observed in Suisun Bay. We used a steady-state, one-dimensional, single-compartment box model of the bay, incorporating terms for advection, exchange, and waste input, to calculate a residual rate for all processes not included in the model. We found that the residual for DIN was related to concentrations of chlorophylla (Chla). The residual for DRP was also related to Chla at high concentrations of Chla, but showed significant losses of DRP at low Chla concentrations. These losses were typically equivalent to about 80% of the wastewater input rate.

Site Occupancies, Luminescence, and Thermometric Properties of LiY9(SiO4)6O2:Ce3+ Phosphors.

PubMed

Zhou, Weijie; Pan, Fengjuan; Zhou, Lei; Hou, Dejian; Huang, Yan; Tao, Ye; Liang, Hongbin

2016-10-04

In this work, we report the tunable emission properties of Ce 3+ in an apatite-type LiY 9 (SiO 4 ) 6 O 2 compound via adjusting the doping concentration or temperature. The occupancies of Ce 3+ ions at two different sites (Wyckoff 6h and 4f sites) in LiY 9 (SiO 4 ) 6 O 2 have been determined by Rietveld refinements. Two kinds of Ce 3+ f-d transitions have been studied in detail and then assigned to certain sites. The effects of temperature and doping concentration on Ce 3+ luminescence properties have been systematically investigated. It is found that the Ce 3+ ions prefer occupying Wyckoff 6h sites and the energy transfer between Ce 3+ at two sites becomes more efficient with an increase in doping concentration. In addition, the charge-transfer vibronic exciton (CTVE) induced by the existence of free oxygen ion plays an important role in the thermal quenching of Ce 3+ at 6h sites. Because of the tunable emissions from cyan to blue with increasing temperature, the phosphors LiY 9 (SiO 4 ) 6 O 2 :Ce 3+ are endowed with possible thermometric applications.

Thermal management of the remote phosphor layer in LED systems

NASA Astrophysics Data System (ADS)

Perera, Indika U.; Narendran, Nadarajah

2013-09-01

Generally in a white light-emitting diode (LED), a phosphor slurry is placed around the semiconductor chip or the phosphor is conformally coated over the chip to covert the narrowband, short-wavelength radiation to a broadband white light. Over the past few years, the remote-phosphor method has provided significant improvement in overall system efficiency by reducing the photons absorbed by the LED chip and reducing the phosphor quenching effects. However, increased light output and smaller light engine requirements are causing high radiant energy density on the remotephosphor plates, thus heating the phosphor layer. The phosphor layer temperature rise increases when the phosphor material conversion efficiency decreases. Phosphor layer heating can negatively affect performance in terms of luminous efficacy, color shift, and life. In such cases, the performance of remote-phosphor LED lighting systems can be improved by suitable thermal management to reduce the temperature of the phosphor layer. To verify this hypothesis and to understand the factors that influence the reduction in temperature, a phosphor layer was embedded in a perforated metal heatsink to remove the heat; the parameters that influence the effectiveness of heat extraction were then studied. These parameters included the heatsink-to-phosphor layer interface area and the thermal conductivity of the heatsink. The temperature of the remote-phosphor surface was measured using IR thermography. The results showed that when the heat conduction area of the heatsink increased, the phosphor layer temperature decreased, but at the same time the overall light output of the remote phosphor light engine used in this study decreased due to light absorption by the metal areas.

Porous texture of activated carbons prepared by phosphoric acid activation of woods

NASA Astrophysics Data System (ADS)

Díaz-Díez, M. A.; Gómez-Serrano, V.; Fernández González, C.; Cuerda-Correa, E. M.; Macías-García, A.

2004-11-01

Activated carbons (ACs) have been prepared using chestnut, cedar and walnut wood shavings from furniture industries located in the Comunidad Autónoma de Extremadura (SW Spain). Phosphoric acid (H3PO4) at different concentrations (i.e. 36 and 85 wt.%) has been used as activating agent. ACs have been characterized from the results obtained by N2 adsorption at 77 K. Moreover, the fractal dimension (D) has been calculated in order to determine the AC surface roughness degree. Optimal textural properties of ACs have been obtained by chemical activation with H3PO4 36 wt.%. This is corroborated by the slightly lower values of D for samples treated with H3PO4 85 wt.%.

The effect of doping Mg2+ on structure and properties of Sr(1.992-x)MgxSiO4: 0.008Eu2+ blue phosphor synthesized by co-precipitation method

NASA Astrophysics Data System (ADS)

Yang, Lingxiang; Wang, Jin-shan; Zhu, Da-chuan; Pu, Yong; Zhao, Cong; Han, Tao

2018-01-01

In order to improve the luminescence property of silicate phosphors, a series of Sr(1.992-x)MgxSiO4: 0.008Eu2+(x = 0, 0.25, 0.50, 0.75) blue phosphors have been synthesized using one-step calcination of a precursor prepared by chemical co-precipitation. And then the crystal structure and luminescence properties of the phosphors are investigated by means of X-Ray Diffraction and spectrophotometer. The results show that β-phase existed in the mixed phases of Sr2SiO4 (β+α‧) would transform to α‧-phase with Mg2+ ions doping into the silicate host until it disappeared. On the other hand, the introduction of Mg2+ ions can enhance the intensity of the excitation spectrum and promote the excitation sensitivity of Sr(1.992-x)MgxSiO4: 0.008Eu2+ phosphors in NUV region. Under NUV excitation at 350 nm, all samples exhibit a broadband emission in range of 400-550 nm due to the 4f65d1→4f7(8S7/2) transition of Eu2+ ions. According to Multi-peak fitting to emission spectra by Gauss method, the broad emission band consists of two single bands with peaks Em1 and Em2 locating at 460 and 490 nm, which corresponds to Eu2+ ions occupying the ten-fold oxygen-coordinated Sr1 site and the nine-fold oxygen-coordinated Sr2 site, respectively. The luminescence intensity of Sr(1.992-x)MgxSiO4:0.008Eu2+(x = 0, 0.25, 0.50, 0.75) blue phosphors has been enhanced remarkably after Mg2+ ions are added. Meanwhile, the chromaticity coordinates change from the blue-green region to the blue region as x moves from 0 to 0.75. Moreover, the decay curves are measured and can be well fitted with double exponential decay equation. It shows that the average lifetime is extended with the concentration of Mg2+ ions increasing. These results indicate that Sr(1.992-x)MgxSiO4: 0.008Eu2+(x = 0, 0.25, 0.50, 0.75) can be used as a potential blue phosphor in near UV-excited white LEDs.

Micro-electro-mechanical systems phosphoric acid fuel cell

DOEpatents

Sopchak, David A [Livermore, CA; Morse, Jeffrey D [Martinez, CA; Upadhye, Ravindra S [Pleasanton, CA; Kotovsky, Jack [Oakland, CA; Graff, Robert T [Modesto, CA

2010-08-17

A phosphoric acid fuel cell system comprising a porous electrolyte support, a phosphoric acid electrolyte in the porous electrolyte support, a cathode electrode contacting the phosphoric acid electrolyte, and an anode electrode contacting the phosphoric acid electrolyte.

Micro-electro-mechanical systems phosphoric acid fuel cell

DOEpatents

Sopchak, David A.; Morse, Jeffrey D.; Upadhye, Ravindra S.; Kotovsky, Jack; Graff, Robert T.

2010-12-21

A phosphoric acid fuel cell system comprising a porous electrolyte support, a phosphoric acid electrolyte in the porous electrolyte support, a cathode electrode contacting the phosphoric acid electrolyte, and an anode electrode contacting the phosphoric acid electrolyte.

Evaluation of ice-tea quality by DART-TOF/MS.

PubMed

Rajchl, Aleš; Prchalová, Jana; Kružík, Vojtěch; Ševčík, Rudolf; Čížková, Helena

2015-11-01

DART (Direct Analysis in Real Time) coupled with Time-of-Flight Mass Spectrometry (TOF/MS) has been used for analyses of ice-teas. The article focuses on quality and authenticity of ice-teas as one of the most important tea-based products on the market. Twenty-one samples of ice-teas (black and green) were analysed. Selected compounds of ice-teas were determined: theobromine, caffeine, total phenolic compounds, total soluble solids, total amino acid concentration, preservatives and saccharides were determined. Fingerprints of DART-TOF/MS spectra were used for comprehensive assessment of the ice-tea samples. The DART-TOF/MS method was used for monitoring the following compounds: citric acid, caffeine, saccharides, artificial sweeteners (saccharin, acesulphame K), and preservatives (sorbic and benzoic acid), phosphoric acid and phenolic compounds. The measured data were subjected to a principal components analysis. The HPLC and DART-TOF/MS methods were compared in terms of determination of selected compounds (caffeine, benzoic acid, sorbic acid and saccharides) in the ice-teas. The DART-TOF/MS technique seems to be a suitable method for fast screening, testing quality and authenticity of tea-based products. Copyright © 2015 John Wiley & Sons, Ltd.

Effect of potassium ferrate on disintegration of waste activated sludge (WAS).

PubMed

Ye, Fenxia; Ji, Haizhuang; Ye, Yangfang

2012-06-15

The activated sludge process of wastewater treatment results in the generation of a considerable amount of excess activated sludge. Increased attention has been given to minimization of waste activated sludge recently. This paper investigated the effect of potassium ferrate oxidation pretreatment on the disintegration of the waste activated sludge at various dosages of potassium ferrate. The results show that potassium ferrate pretreatment disintegrated the sludge particle, resulting in the reduction of total solid content by 31%. The solubility (SCOD/TCOD) of the sludge increased with the increase of potassium ferrate dosage. Under 0.81 g/g SS dosage of potassium ferrate, SCOD/TCOD reached 0.32. Total nitrogen (TN) and total phosphorous (TP) concentrations in the solution all increased significantly after potassium ferrate pretreatment. The sludge particles reduced from 116 to 87 μm. The settleability of the sludge (SVI) was enhanced by 17%, which was due to the re-flocculation by the by-product, Fe(III), during potassium ferrate oxidation and the decrease of the viscosity. From the result of the present investigations, it can be concluded that potassium ferrate oxidation is a feasible method for disintegration of excess activated sludge. Copyright © 2012 Elsevier B.V. All rights reserved.

Understanding fine sediment and phosphorous delivery in upland catchments

NASA Astrophysics Data System (ADS)

Perks, M. T.; Reaney, S. M.

2013-12-01

The uplands of UK are heavily impacted by land management including; farming and forestry operations, moorland burning, peat extraction, metal mining, artificial drainage and channelisation. It has been demonstrated that such land management activity may modify hillslope processes, resulting in enhanced runoff generation and changing the spatial distribution and magnitude of erosion. Resultantly, few upland river systems of the UK are operating in a natural state, with land management activity often resulting in increased fluxes of suspended sediment (< 2 mm) and associated pollutants (such as phosphorous). Most recent Environment Agency (EA) data reveals that 60% of monitored water bodies within upland areas of the UK are currently at risk of failing the Water Framework Directive (WFD) due to poor ecological status. In order to prevent the continual degradation of many upland catchments, riverine systems and their diverse ecosystems, a range of measures to control diffuse pollution will need to be implemented. Future mitigation options and measures in the UK may be tested and targeted through the EA's catchment pilot scheme; DEFRA's Demonstration Test Catchment (DTC) programmes and through the catchment restoration fund. However, restoring the physical and biological processes of past conditions in inherently sensitive upland environments is extremely challenging requiring the development of a solid evidence base to determine the effectiveness of resource allocation and to enable reliable and transparent decisions to be made about future catchment operations. Such evidence is rarely collected, with post-implementation assessments often neglected. This paper presents research conducted in the Morland sub-catchment of the River Eden within Cumbria; UK. 80% of this headwater catchment is in upland areas and is dominated by improved grassland and rough grazing. The catchment is heavily instrumented with a range of hydro-meteorological equipment. A high-tech monitoring station at the 12.5 km2 outlet provides flow, turbidity, total phosphorous (TP), total reactive phosphorous (TRP), conductivity, temperature and pH measurements at 15-minute intervals. Within this catchment, two additional monitoring stations along adjacent tributaries with catchment areas of 2.3 km2 and 3.8 km2 provide continuous flow and turbidity data with soluble reactive phosphorous and TP collected during storms. Collection and analysis of this data over two full hydrological years has proved effective in; a) producing load estimates; b) producing better assessments of the magnitude and duration of aquatic organisms exposure to detrimental levels of suspended sediment and phosphorous; c) exploring the processes responsible for the delivery and transfer of fine sediment and phosphorous to and from the channel and; d) enhancing our understanding and prediction of the fluvial sediment system. The process understanding achieved using this monitoring framework has facilitated the production of a mitigation plan for the Morland catchment. Following this plan, a range of measures are currently being implemented to reduce the movement of diffuse pollutants across the hillslopes and channels whilst in-stream monitoring continues. The adopted mitigation measures may act as a trial for other upland catchments facing similar pressures.

Effect of the transit through the gut of earthworm (Eisenia fetida) on fractionation of Cu and Zn in pig manure.

PubMed

Li, Lingxiangyu; Wu, Jianyang; Tian, Guangming; Xu, Zhenlan

2009-08-15

To investigate the effect of the transit through the gut of earthworm (Eisenia fetida) on the fractionation of Cu and Zn in pig manure, earthworms were reared with pig manure in the greenhouse. Both the pig manure and the earthworm casts were subjected to a five-step sequential extraction of Cu and Zn. The content of Cu bound to organic matter in pig manure increased from 60% to 75% after transit through the gut of earthworm, whereas that of Zn decreased from 50% to 25%. It demonstrated that Cu had a strong affinity towards organic matter. The share of Cu and Zn in the exchangeable fraction was reduced by the transit through the gut of earthworm. Based on these changes, Cu was more bioavailable, whereas Zn was less bioavailable. The factors affecting metal fractionation, like pH, organic matter (OM) and total phosphorous (TP) contents, and total metal concentration, were also affected significantly by the transit through the gut of earthworm. Stepwise multiple regression analysis revealed that the fractionation of Cu in the earthworm casts was influenced by OM, TP and the amount of Cu in the earthworm casts. The total Zn concentration in the earthworm casts was the primary factor that explained most of the variation in Zn fractionation. The present study demonstrated that the digestive activity in the gut of E. fetida played an important role in the fraction redistribution of Cu and Zn in pig manure.

The Daily Consumption of Cola Can Determine Hypocalcemia: A Case Report of Postsurgical Hypoparathyroidism-Related Hypocalcemia Refractory to Supplemental Therapy with High Doses of Oral Calcium.

PubMed

Guarnotta, Valentina; Riela, Serena; Massaro, Marina; Bonventre, Sebastiano; Inviati, Angela; Ciresi, Alessandro; Pizzolanti, Giuseppe; Benvenga, Salvatore; Giordano, Carla

2017-01-01

The consumption of soft drinks is a crucial factor in determining persistent hypocalcemia. The aim of the study is to evaluate the biochemical mechanisms inducing hypocalcemia in a female patient with usual high consumption of cola drink and persistent hypocalcemia, who failed to respond to high doses of calcium and calcitriol supplementation. At baseline and after pentagastrin injection, gastric secretion (Gs) and duodenal secretion (Ds) samples were collected and calcium and total phosphorus (P tot ) concentrations were evaluated. At the same time, blood calcium, P tot , sodium, potassium, chloride, magnesium concentrations, and vitamin D were sampled. After intake of cola (1 L) over 180 min, Gs and Ds and blood were collected and characterized in order to analyze the amount of calcium and P tot or sodium, potassium, magnesium, and chloride ions, respectively. A strong pH decrease was observed after cola intake with an increase in phosphorus concentration. Consequently, a decrease in calcium concentration in Gs and Ds was observed. A decrease in calcium concentration was also observed in blood. In conclusion, we confirm that in patients with postsurgical hypoparathyroidism, the intake of large amounts of cola containing high amounts of phosphoric acid reduces calcium absorption efficiency despite the high doses of calcium therapy.

Comparison between mixed and spatially separated remote phosphor fabricated via a screen-printing process

NASA Astrophysics Data System (ADS)

Kim, Byung-Ho; Hwang, Jonghee; Lee, Young Jin; Kim, Jin-Ho; Jeon, Dae-Woo; Lee, Mi Jai

2016-08-01

We developed a fabrication method for remote phosphor by a screen-printing process, using green phosphor, red phosphor, and thermally stable glass frit. The glass frit was introduced for long-term stability. The optical properties of the remote phosphor were observed via an integrating sphere; the photoluminescence spectrum dramatically changed on incorporating a minor amount of the red phosphor. These unique optical properties were elucidated using four factors: phosphor ratio, scattering induced by packing density, light intensity per unit volume, and reabsorption. The thermal stability of the remote phosphor was investigated at 500°C, demonstrating its outstanding thermal properties.

Exploring Soil Ecosystems.

ERIC Educational Resources Information Center

Finley, Deborah R.

1991-01-01

Describes a soil lab that can be performed with a minimum of equipment and time, utilizing a lawn, field, or woodlot. Students dig a 1-meter-deep pit and observe the litter and humus layers where most microbial and fungal decomposition occurs. Describes comparing different locations by pH level and concentration of potassium, phosphorous, and…

Aquatic Nutrient Simulation Modules (NSMs) Developed for Hydrologic and Hydraulic Models

DTIC Science & Technology

2016-02-01

effect of temperature on algal growth unitless FOxpi oxygen attenuation for algal respiration unitless FOxb oxygen attenuation for benthic algal... effect of temperature below T0p on benthic algal growth 0C-2 ktb2 effect of temperature above T0p on benthic algal growth 0C-2 ka(T) oxygen ...Si Silica SOD Sediment Oxygen Demand SO4 TEMP Sulfate Water Temperature Simulation Module TN Total Nitrogen TP Total Phosphorous TIC Total

Trophic status and assessment of non-point nutrient enrichment of Lake Crescent Olympic National Park

USGS Publications Warehouse

Boyle, Terence P.; Beeson, David R.

1991-01-01

A limited effort study was conducted in Lake Crescent, Olympic National Park to determine the trophic status and assess whether non-point nutrients were leaching into the lake and affecting biological resources. The concentration of chlorophyll a, total nitrogen concentration, and Secchi disk transparency used as parameters of the Trophic Status Index revealed that Lake Crescent in Olympic National Park was in the oligotrophic range. Evaluation of the nitrogen to phosphorous ration revealed that nitrogen was the nutrient limiting to overall lake productivity. Single species and community bioassays indicated that other nutrients, possibly iron, had some secondary control over community composition of the algal community. Assessment of six near-shore sites for the presence and effects of non-point nutrients revealed that La Poel Point which formerly was the site of a resort had slightly higher algal bioassay and periphyton response than the other sites. No conditions that would require immediate action by resource management of Olympic National Park were identified. The general recommendations for a long term lake monitoring plan are discussed.

High-power laser phosphor light source with liquid cooling for digital cinema applications

NASA Astrophysics Data System (ADS)

Li, Kenneth

2014-02-01

Laser excited phosphor has been used to excite phosphor material, producing high intensity light output with smaller etendue than that of LEDs with the same long lifetime. But due to the high intensity of the laser light, phosphor with organic binder burns at low power, which requires the phosphor to be deposited on a rotating wheel in practical applications. Phosphor with inorganic binders, commonly known as ceramic phosphor, on the other hand, does not burn, but efficiency goes down as temperature goes up under high power excitation. This paper describes cooling schemes in sealed chambers such that the phosphor materials using organic or inorganic binders can be liquid cooled for high efficiency operations. Confined air bubbles are introduced into the sealed chamber accommodating the differential thermal expansion of the liquid and the chamber. For even higher power operation suitable for digital cinema, a suspension of phosphor in liquid is described suitable for screen brightness of over 30,000 lumens. The aging issues of phosphor can also be solved by using replaceable phosphor cartridges.

Structural and optical investigation in Er3+ doped Y2MoO6 phosphors

NASA Astrophysics Data System (ADS)

Mondal, Manisha; Rai, Vineet Kumar

2018-05-01

The Er3+ doped Y2MoO6 phosphors have been structurally and optically characterized by X-ray Diffraction (XRD), Field emission scanning electron microscopy (FESEM), UV-Vis absorption spectroscopy and frequency upconversion (UC) emission studies. The crystal and the particles size are found to be ˜ 85 nm and ˜ 200 nm from XRD and FESEM analysis. The intense peak at ˜ 206 nm in the UV-Vis absorption spectroscopy is attributed due to the charge transfer transition between the Mo6+ and the O2- ions in the MoO4 group in the host molybdate. The frequency UC emission studies of the prepared phosphors under 980 nm diode laser excitation shows the intense UC emission in the 0.3 mol% concentrations for the Er3+ ions. In the UC emission spectra, the emission peaks at green (˜ 525 nm and ˜ 546 nm) and red (˜ 656 nm) bands are corresponding to the 2H11/2, 4S3/2 → 4I15/2 and 4F9/2 → 4I15/2 transitions of Er3+ ions. The mechanisms involved in the UC process have been explored with the help of energy level diagram. Moreover, the CIE point (0.31, 0.60) lie in the green colour region which indicates that the developed phosphor have suitable applications in NIR to visible upconverter and in making green light display devices.

Temperature-dependent OSL properties of nano-phosphors LiAlO2:C and α-Al2O3:C

NASA Astrophysics Data System (ADS)

Agarwal, Mini; Garg, Sandeep K.; Asokan, K.; Kumar, Pratik

2018-06-01

The present study focuses on the synthesis and characterization of carbon doped nano-phosphors, LiAlO2 and α-Al2O3 and their temperature-dependent optically stimulated luminescence (TA-OSL) characteristics in the temperature ranges of 25-350 °C. These nano-phosphors with the carbon concentration of 0.01 mol% exhibits high luminescent intensity for LiAlO2:C in the low dose range of 1 mGy-7 Gy and for α-Al2O3:C in the range of 100 mGy-1 kGy. Both these nano-phosphors are of polycrystalline in nature, having grain size 15-50 nm as confirmed by the X-ray diffraction (XRD) and Transmission Electron Microscopy (TEM), respectively. The maximum TA-OSL intensities are observed at 125 °C for LiAlO2:C and 200 °C for Al2O3:C, and reveal the presence of deep defect centres. The Arrhenius analysis shows the activation energies Ea = 0.06 ± 0.02 eV for LiAlO2:C and Ea = 0.04 ± 0.01 eV, & Eb = 0.48 ± 0.07 eV for Al2O3:C. The TA-OSL and OSL characteristics are discussed with special reference to the medical and high radiation dosimetry. These compounds, LiAlO2:C and α-Al2O3:C, are non-toxic, robust and are potential candidates for reusable dosimetry.

Tunable color and energy transfer in single-phase white-emitting Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68}:Ce{sup 3+},Dy{sup 3+} phosphors for UV white light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan, Bo; Song, Yanhua; Sheng, Ye

Ce{sup 3+} and/or Dy{sup 3+} activated Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68} phosphors were synthesized by high temperature solid state reaction and their luminescent properties were studied. There are two emissions peaking at 407 and 577 nm in the emission spectra of Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68}:Ce{sup 3+}, Dy{sup 3+}, which are due to the transitions of Ce{sup 3+} and Dy{sup 3+} ions, respectively. More importantly, the effective energy transfer from Ce{sup 3+} to Dy{sup 3+} ions has been confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and mechanism of energy transfermore » were investigated and it was demonstrated to be resonant type via dipole–dipole reaction. Under the excitation of 345 nm, the emitting color can change from blue to white by adjusting the relative doping concentration of Ce{sup 3+} and Dy{sup 3+} ions, indicating that the phosphors Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68}:Ce{sup 3+}, Dy{sup 3+} are promising single-phase white-emitting phosphors for application in pc-white LEDs. - Highlights: • The Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68}:Ce{sup 3+},Dy{sup 3+} are novel luminescent materials that have not been reported before. • The crystal structure of Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68} and energy transfer from Ce{sup 3+} to Dy{sup 3+} were investigated. • The emission color of Ca{sub 20}Al{sub 26}Mg{sub 3}Si{sub 3}O{sub 68}:Ce{sup 3+},Dy{sup 3+} can be adjusted from blue to white. • The phosphors have great application value in WLEDs as a kind of blue-to-white emitting phosphors.« less

Properties of blue emitting CaAl2O4:Eu2+, Nd3+ phosphor by optimizing the amount of flux and fuel

NASA Astrophysics Data System (ADS)

Wako, A. H.; Dejene, B. F.; Swart, H. C.

2014-04-01

Long afterglow CaAl2O4:0.03Eu2+, 0.03Nd3+ phosphor was prepared by solution-combustion synthesis. The active role of boric acid (H3BO3) as a flux in enhancing the Eu2+ photoluminescence and the effect of a varied amount of urea (CO (NH2)2) as a fuel on the morphological, structural and photoluminescent (PL) properties of the CaAl2O4:0.03Eu2+, 0.03Nd3+ systems were investigated. The results of X-ray diffraction, scanning electron microscopy, and PL spectra revealed the influence of the dosage of urea and hence the heated process on the crystallinity, morphology, and luminescence of the phosphor. The addition of H3BO3 favoured the formation of a monoclinic CaAl2O4 phase while the variation of the amount of CO (NH2)2 showed mixed phases although still predominantly monoclinic. Both H3BO3 and CO(NH2)2 to some extent influence the luminescence intensity of the obtained phosphor but unlike the case of CO(NH2)2, the presence of H3BO3 did not evidently shift the emission peak due to no obvious change in the energy level difference of the 4f-5d levels. The broad blue emissions consisting mainly of symmetrical bands having maxima between 440 and 445 nm originate from the energy transitions between the ground state (4f7) and the excited state (4f65d1) of the Eu2+ ions while the narrow emissions in the red region (600-630 nm) arise from the 5D0→7F2 transitions of the remnant unreduced Eu3+ions. Higher concentrations of H3BO3 (0.228 mol and 0.285 mol) reduce both intensity and lifetime of the phosphor. The optimized content of H3BO3 was 0.171 mol for the obtained phosphor with the best optical properties.

Selecting the optimal synthesis parameters of InP/CdxZn1-xSe quantum dots for a hybrid remote phosphor white LED for general lighting applications.

PubMed

Ryckaert, Jana; Correia, António; Tessier, Mickael D; Dupont, Dorian; Hens, Zeger; Hanselaer, Peter; Meuret, Youri

2017-11-27

Quantum dots can be used in white LEDs for lighting applications to fill the spectral gaps in the combined emission spectrum of the blue pumping LED and a broad band phosphor, in order to improve the source color rendering properties. Because quantum dots are low scattering materials, their use can also reduce the amount of backscattered light which can increase the overall efficiency of the white LED. The absorption spectrum and narrow emission spectrum of quantum dots can be easily tuned by altering their synthesis parameters. Due to the re-absorption events between the different luminescent materials and the light interaction with the LED package, determining the optimal quantum dot properties is a highly non-trivial task. In this paper we propose a methodology to select the optimal quantum dot to be combined with a broad band phosphor in order to realize a white LED with optimal luminous efficacy and CRI. The methodology is based on accurate and efficient simulations using the extended adding-doubling approach that take into account all the optical interactions. The method is elaborated for the specific case of a hybrid, remote phosphor white LED with YAG:Ce phosphor in combination with InP/CdxZn 1-x Se type quantum dots. The absorption and emission spectrum of the quantum dots are generated in function of three synthesis parameters (core size, shell size and cadmium fraction) by a semi-empirical 'quantum dot model' to include the continuous tunability of these spectra. The sufficiently fast simulations allow to scan the full parameter space consisting of these synthesis parameters and luminescent material concentrations in terms of CRI and efficacy. A conclusive visualization of the final performance allows to make a well-considered trade-off between these performance parameters. For the hybrid white remote phosphor LED with YAG:Ce and InP/CdxZn 1-x Se quantum dots a CRI Ra = 90 (with R9>50) and an overall efficacy of 110 lm/W is found.

Modeled long-term changes of DIN:DIP ratio in the Changjiang River in relation to Chl-α and DO concentrations in adjacent estuary

NASA Astrophysics Data System (ADS)

Wang, Jianing; Yan, Weijin; Chen, Nengwang; Li, Xinyan; Liu, Lusan

2015-12-01

In the past four decades (1970-2013), nitrogen and phosphorous inputs to the Changjiang River basin, mainly from human activities, have increased 3-fold and 306-fold, respectively. The riverine nutrient fluxes to the estuary have also grown exponentially. Dissolved inorganic nitrogen (DIN) and dissolved inorganic phosphorous (DIP) fluxes of the Changjiang River increased by 338% and 574% during 1970-2013 period, and red tides and benthic hypoxia have been observed in the outflow region of the Changjiang River in the East China Sea (ECS). We assumed that time series changes in the DIN:DIP ratio from the Changjiang River could have a significant impact on Chlorophyll-α (Chl-α) concentration in the surface sea water and dissolved oxygen (DO) concentration in the bottom sea water of the Changjiang estuary. Our study showed that the DIN:DIP ratio from the Changjiang River increased from 76 to 384 between 1970 and 1985, and decreased from 255 to 149 between 1986 and 2013. The observed Chl-α concentration increased by 146% from 1992 to 2010 in the Changjiang estuary, and was negatively related to the DIN:DIP ratio in 1992-2010. Bottom sea water DO concentration decreased by 24.6% during 1992-2010 and a "low oxygen zone" (122°∼123°E, 32°∼33°N) was observed during summer since 1999. The anthropogenically enhanced nutrient inputs dominated river DIN and DIP fluxes and influenced Chl-α concentrations as well as bottom DO concentrations in the estuary. Scenarios emphasizing global collaboration and proactive environmental problem-solving may result in reductions in the river nutrient exports and in Chl-α and DO concentration in the Changjiang estuary by 2050.

Enzymatic glucose sensor compensation for variations in ambient oxygen concentration

NASA Astrophysics Data System (ADS)

Collier, Bradley B.; McShane, Michael J.

2013-02-01

Due to the increasing prevalence of diabetes, research toward painless glucose sensing continues. Oxygen sensitive phosphors with glucose oxidase (GOx) can be used to determine glucose levels indirectly by monitoring oxygen consumption. This is an attractive combination because of its speed and specificity. Packaging these molecules together in "smart materials" for implantation will enable non-invasive glucose monitoring. As glucose levels increase, oxygen levels decrease; consequently, the luminescence intensity and lifetime of the phosphor increase. Although the response of the sensor is dependent on glucose concentration, the ambient oxygen concentration also plays a key role. This could lead to inaccurate glucose readings and increase the risk of hyper- or hypoglycemia. To mitigate this risk, the dependence of hydrogel glucose sensor response on oxygen levels was investigated and compensation methods explored. Sensors were calibrated at different oxygen concentrations using a single generic logistic equation, such that trends in oxygen-dependence were determined as varying parameters in the equation. Each parameter was found to be a function of oxygen concentration, such that the correct glucose calibration equation can be calculated if the oxygen level is known. Accuracy of compensation will be determined by developing an overall calibration, using both glucose and oxygen sensors in parallel, correcting for oxygen fluctuations in real time by intentionally varying oxygen, and calculating the error in actual and predicted glucose levels. While this method was developed for compensation of enzymatic glucose sensors, in principle it can also be implemented with other kinds of sensors utilizing oxidases.

A Volumetric Method for Titrimetric Analysis of Hydrogen Peroxide

DTIC Science & Technology

1985-05-06

fairly satisfactory indicator. Sulfuric acid solutions of cerium are stable over long periods of time, unlike the less stable nitric and hydrochloric acid ...Fisher number D141-5. 5. Sulfuric acid , concentrated (95-98 percent). For example, Fisher number A 300-212. 6. O-Phosphoric acid , 85 percent:. For example...Fisher number A 242-500. 7. 5 N sulfuric acid (Reference 11): Slowly pour 75 mL of concentrated sulfuric acid (95-98 percent) into approximately 200

Saliva with reduced calcium and phosphorous concentrations: Effect on erosion dental lesions.

PubMed

Denucci, Giovanna Corrêa; Mantilla, Taís Fonseca; Amaral, Flávia Lucisano Botelho; Basting, Roberta Tarkany; França, Fabiana Mantovani Gomes; Turssi, Cecilia Pedroso

2018-02-08

To investigate whether saliva formulations with reduced calcium (Ca) and inorganic phosphorous (Pi) concentration would affect dental erosion caused by hydrochloric acid (HCl). Enamel and root dentine bovine slabs were embedded, polished and measured for surface Knoop microhardness (SMH). After reference areas were created, specimens were exposed to HCl solution (0.01M; pH 2; 120s) and immersed in artificial salivas (6h) containing three different Ca/Pi concentrations (n=15), which simulate serum conditions of normo-, mild- or severe hypocalcaemia. The control group was immersed in Ca/Pi-free saliva. The study protocol was carried out 2x/day for 5 days. Surface loss of enamel and root dentine was assessed using an optical profilometer and SMH was remeasured for enamel. ANOVA (p<0.001) and Tukey's test showed that enamel loss in groups subjected to artificial salivas that simulated mild- or severe hypocalcaemia did not differ from that resembling normocalcemia. %SMH was lower when saliva was mildly- and normally-concentrated in Ca/Pi (p<0.001). Root dentine loss was higher in saliva simulating severe hypocalcaemia than in those referring to mild, hypo- and normocalcemia. Depending on the dental substrate, salivary formulations resembling serum hypocalcaemia affected surface loss due to erosion and rehardening thereof. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Use of Landsat data to predict the trophic state of Minnesota lakes

NASA Technical Reports Server (NTRS)

Lillesand, T. M.; Johnson, W. L.; Deuell, R. L.; Lindstrom, O. M.; Meisner, D. E.

1983-01-01

Near-concurrent Landsat Multispectral Scanner (MSS) and ground data were obtained for 60 lakes distributed in two Landsat scene areas. The ground data included measurement of secchi disk depth, chlorophyll-a, total phosphorous, turbidity, color, and total nitrogen, as well as Carlson Trophic State Index (TSI) values derived from the first three parameters. The Landsat data best correlated with the TSI values. Prediction models were developed to classify some 100 'test' lakes appearing in the two analysis scenes on the basis of TSI estimates. Clouds, wind, poor image data, small lake size, and shallow lake depth caused some problems in lake TSI prediction. Overall, however, the Landsat-predicted TSI estimates were judged to be very reliable for the secchi-derived TSI estimation, moderately reliable for prediction of the chlorophyll-a TSI, and unreliable for the phosphorous value. Numerous Landsat data extraction procedures were compared, and the success of the Landsat TSI prediction models was a strong function of the procedure employed.

Method to produce nanocrystalline powders of oxide-based phosphors for lighting applications

DOEpatents

Loureiro, Sergio Paulo Martins; Setlur, Anant Achyut; Williams, Darryl Stephen; Manoharan, Mohan; Srivastava, Alok Mani

2007-12-25

Some embodiments of the present invention are directed toward nanocrystalline oxide-based phosphor materials, and methods for making same. Typically, such methods comprise a steric entrapment route for converting precursors into such phosphor material. In some embodiments, the nanocrystalline oxide-based phosphor materials are quantum splitting phosphors. In some or other embodiments, such nanocrystalline oxide based phosphor materials provide reduced scattering, leading to greater efficiency, when used in lighting applications.

Phosphor blends for high-CRI fluorescent lamps

DOEpatents

Setlur, Anant Achyut [Niskayuna, NY; Srivastava, Alok Mani [Niskayuna, NY; Comanzo, Holly Ann [Niskayuna, NY; Manivannan, Venkatesan [Clifton Park, NY; Beers, William Winder [Chesterland, OH; Toth, Katalin [Pomaz, HU; Balazs, Laszlo D [Budapest, HU

2008-06-24

A phosphor blend comprises at least two phosphors each selected from one of the groups of phosphors that absorb UV electromagnetic radiation and emit in a region of visible light. The phosphor blend can be applied to a discharge gas radiation source to produce light sources having high color rendering index. A phosphor blend is advantageously includes the phosphor (Tb,Y,LuLa,Gd).sub.x(Al,Ga).sub.yO.sub.12:Ce.sup.3+, wherein x is in the range from about 2.8 to and including 3 and y is in the range from about 4 to and including 5.

A flux-free method for synthesis of Ce{sup 3+}-doped YAG phosphor for white LEDs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiang, Yaochun; Yu, Yuxi, E-mail: yu_heart@xmu.edu.cn; Chen, Guolong

2016-02-15

Highlights: • A series of CeF{sub 3}-doped YAG phosphors were successfully synthesized. • CeF{sub 3} not only can be used as the Ce{sup 3+} source but also can play the role of a flux. • The QY of YAG:CeF{sub 3} phosphor is 91% but the QY of YAG:Ce{sub 2}O{sub 3} phosphor is just 80%. • YAG:CeF{sub 3} phosphor exhibits excellent thermal stability. • Using CeF{sub 3} as the Ce{sup 3+} source is a promising flux-free method to prepare YAG:Ce{sup 3+}. - Abstract: A series of CeF{sub 3}-doped Y{sub 3}Al{sub 5}O{sub 12} (YAG:CeF{sub 3}) phosphor, CeO{sub 2}-doped Y{sub 3}Al{sub 5}O{sub 12}more » (YAG:Ce{sub 2}O{sub 3}) phosphor and 5 wt% BaF{sub 2} added YAG:Ce{sub 2}O{sub 3} (YAG:Ce{sub 2}O{sub 3} + BaF{sub 2}) phosphor were successfully synthesized by a solid-state reaction method. The microstructure, morphology, luminescence spectra, luminescence quantum yield (QY) and thermal quenching of the phosphors were investigated. The QY of YAG:CeF{sub 3} phosphor is 91% but the QY of YAG:Ce{sub 2}O{sub 3} phosphor is just 80%. At 150 °C, the luminescence intensity of YAG:CeF{sub 3} phosphor, YAG:Ce{sub 2}O{sub 3} phosphor and YAG:Ce{sub 2}O{sub 3} + BaF{sub 2} phosphor was 85%, 86% and 89% of that measured at 25 °C, respectively. The comprehensive performance of the white LED lamp employing YAG:CeF{sub 3} phosphor is even better than that of the white LED lamp employing YAG:Ce{sub 2}O{sub 3} + BaF{sub 2} phosphor. The experimental results show that it is a promising flux-free method to synthesize Ce{sup 3+}-doped YAG phosphor by employing CeF{sub 3} as the Ce{sup 3+} source.« less

Biogeochemical Cycling of Iron and Phosphorous in Deep Saprolite

NASA Astrophysics Data System (ADS)

Buss, H. L.; Bruns, M. A.; Williams, J. Z.; White, A. F.; Brantley, S. L.

2006-12-01

Few microbiological studies have been conducted within the unsaturated zones between rooting depth and bedrock and thus the relationships between biological activity and mineral nutrient cycling in deep regolith are poorly understood. Here we investigate the weathering of primary minerals containing iron (hornblende and biotite) and phosphorous (apatite) and the role of resident microorganisms in the cycling of these elements in the deep saprolite of the Rio Icacos watershed in Puerto Rico's Luquillo Mountains. In the Rio Icacos watershed, which has one of the fastest documented chemical weathering rates of granitic rock in the world, the quartz diorite bedrock weathers spheroidally, producing a complex interface comprised of partially weathered rock layers called rindlets. This rindlet zone (0.2-2 m thick) is overlain by saprolite (2-8 m) topped by soil (0.5-1 m). With the objective of understanding interactions among mineral weathering, substrate availability and resident microorganisms, we made geochemical and microbiological measurements as a function of depth in 5 m of regolith (soil + saprolite) and examined mineral weathering reactions within a 0.5 m thick spheroidally weathering rindlet zone. We measured total cell densities, culturable aerobic chemoorganotrophs, and microbial DNA yields; and performed biochemical tests for iron-oxidizing bacteria in the regolith samples. Total cell densities, which ranged from 2.5 x 106 to 1.6 x 1010 g-1 regolith, were higher than 108 g-1 at three depths: in the upper 1 m, at 2.1 m, and between 3.7-4.9 m, just above the rindlet zone. Biochemical tests for aerobic iron-oxidizers were also positive at 0.15-0.6 m, at 2.1-2.4 m, and at 4.9 m depths. High proportions of inactive or unculturable cells were indicated throughout the profile by very low percentages of culturable chemoorganotrophs. The observed increases in total and culturable cells and DNA yields at lower depths were correlated with an increase in HCl-extractable Fe in the deep saprolite and coincided with decreases in mineral bound iron and phosphorous due to hornblende and apatite weathering, respectively. Within a 0.07 m zone spanning the rindlet-saprolite interface, we documented the fastest rate of hornblende dissolution in the field ever reported: 6.0 x 10^{-13 mol m-2 s-1. To interpret microbial populations within the context of weathering reactions, we developed a model for estimating growth rates of lithoautotrophs and chemoorganotrophs based on measured substrate fluxes. The calculations and observations are consistent with a model wherein electron donor flux driving bacterial growth at the saprolite-bedrock interface is dominated by the rapid release of Fe(II) during hornblende dissolution and where fixation of CO2 by autotrophic iron-oxidizing bacteria supports growth of chemoorganotrophic bacteria. Apatite weathering, which is the primary source of phosphorous to the deep saprolite ecosystem, occurs at a rate of 4.7 x 10^{-15} mol m-2 s-1 within the rindlet zone. Further measurements of phosphorous within the saprolite are underway and the influence of the phosphorous flux on the lithoautotrophic and chemoorganotrophic growth rates in the deep saprolite will be presented.

Characterization of streamflow, suspended sediment, and nutrients entering Galveston Bay from the Trinity River, Texas, May 2014–December 2015

USGS Publications Warehouse

Lucena, Zulimar; Lee, Michael T.

2017-02-21

The U.S. Geological Survey (USGS), in cooperation with the Texas Water Development Board and the Galveston Bay Estuary Program, collected streamflow and water-quality data at USGS streamflow-gaging stations in the lower Trinity River watershed from May 2014 to December 2015 to characterize and improve the current understanding of the quantity and quality of freshwater inflow entering Galveston Bay from the Trinity River. Continuous streamflow records at four USGS streamflow-gaging stations were compared to quantify differences in streamflow magnitude between upstream and downstream reaches of the lower Trinity River. Water-quality conditions were characterized from discrete nutrient and sedi­ment samples collected over a range of hydrologic conditions at USGS streamflow-gaging station 08067252 Trinity River at Wallisville, Tex. (hereinafter referred to as the “Wallisville site”), approximately 4 river miles upstream from where the Trinity River enters Galveston Bay.Based on streamflow records, annual mean outflow from Livingston Dam into the lower Trinity River was 2,240 cubic feet per second (ft3/s) in 2014 and 22,400 ft3/s in 2015, the second lowest and the highest, respectively, during the entire period of record (1966–2015). During this study, only about 54 percent of the total volume measured at upstream sites was accounted for at the Wallisville site as the Trinity River enters Galveston Bay. This difference in water volumes between upstream sites and the Wallisville site indicates that at high flows a large part of the volume released from Lake Livingston does not reach Galveston Bay through the main channel of the Trinity River. These findings indicate that water likely flows into wetlands and water bodies surrounding the main channel of the Trinity River before reaching the Wallisville site and is being stored or discharged through other channels that flow directly into Galveston Bay.To characterize suspended-sediment concentrations and loads in Trinity River inflow to Galveston Bay, a regression model was developed to estimate suspended-sediment concentrations by using acoustic backscatter data as a surrogate. The model yielded an adjusted coefficient of determination value of 0.92 and a root mean square error of 1.65 milligrams per liter (mg/L). The mean absolute percentage error between measured and estimated suspended-sediment concentration was 35 percent. During this study, estimated suspended-sediment concentrations ranged from 2 to 701 mg/L, with a mean of 97 mg/L. Suspended-sediment concentrations varied in response to changes in discharge, with peak suspended-sediment concentrations occurring 1 to 2 days before the peak discharge for each event. The total suspended-sediment load at the Wallisville site during May 2014–December 2015 was approximately 2,200,000 tons, with a minimum monthly suspended-sediment load of 100 tons in October 2014 and a maximum monthly load of 441,000 tons in November 2015.Results from nutrient samples collected at the Wallisville site indicate that total nitrogen and total phosphorus concen­trations fluctuated at a similar rate, with the highest nutrient concentrations occurring during periods of high flow corresponding to releases from Lake Livingston. The mean concen­trations of total nitrogen and total phosphorus were approxi­mately 75 percent higher during high flow releases than during periods of low flow, overshadowing variations in nutrient concentrations caused by seasonality at the Wallisville site.Results from the study indicate nutrient delivery to Galveston Bay from the main channel of the Trinity River is likely controlled primarily by high-flow releases from Lake Livingston. For most samples collected at the Wallisville site, organic nitrogen was the predominant form of nitrogen; however, when discharge increased because of releases from Lake Livingston, the percentage of organic nitrogen typically decreased and the percentage of nitrate increased. The concentrations of total phosphorus also increased during high-flow events, likely as a result of suspended sediment within Lake Livingston releases and mobilization of sediment particles in the river channel and flood plain during these periods of high flow. The predominant source of phosphorous to Galveston Bay from the Trinity River is in particulate form closely tied to suspended-sediment concentrations. The changes in nutrient concentration and composition caused by releases from Lake Livingston during this study indicate the reservoir may play an important role in the delivery of nutrients into Galveston Bay. Further study is required to better understand the processes in Lake Livingston influencing the characteristics of nutrient and sediment inflow to Galveston Bay. With phosphorous concentrations correlated to suspended-sediment concentra­tions (coefficient of determination value of 0.75) and with the concentrations of nutrients changing as the discharge changes, the diversion of water and suspended sediment into surround­ing wetlands and channels outside of the main channel of the Trinity River may play a large role in regulating nutrient inputs into Galveston Bay.

Plasma impregnation of wood with fire retardants

NASA Astrophysics Data System (ADS)

Pabeliña, Karel G.; Lumban, Carmencita O.; Ramos, Henry J.

2012-02-01

The efficacy of chemical and plasma treatments with phosphate and boric compounds, and nitrogen as flame retardants on wood are compared in this study. The chemical treatment involved the conventional method of spraying the solution over the wood surface at atmospheric condition and chemical vapor deposition in a vacuum chamber. The plasma treatment utilized a dielectric barrier discharge ionizing and decomposing the flame retardants into innocuous simple compounds. Wood samples are immersed in either phosphoric acid, boric acid, hydrogen or nitrogen plasmas or a plasma admixture of two or three compounds at various concentrations and impregnated by the ionized chemical reactants. Chemical changes on the wood samples were analyzed by Fourier transform infrared spectroscopy (FTIR) while the thermal changes through thermo gravimetric analysis (TGA). Plasma-treated samples exhibit superior thermal stability and fire retardant properties in terms of highest onset temperature, temperature of maximum pyrolysis, highest residual char percentage and comparably low total percentage weight loss.

Two-photon luminescence lifetime imaging microscopy (LIM) to follow up cell metabolism and oxygen consumption during theranostic applications

NASA Astrophysics Data System (ADS)

Rück, A.; Breymayer, J.; Lilge, L.; Mandel, A.; Schäfer, P.; von Einem, B.; von Arnim, C.; Kalinina, S.

2018-02-01

A common property during tumor development is altered energy metabolism, which could lead to a switch from oxidative phosphorylation and glycolysis. The impact of this switch for theranostic applications could be significant. Interestingly altered metabolism could be correlated with a change in the fluorescence lifetimes of both NAD(P)H and FAD. However, as observed in a variety of investigations, the situation is complex and the result is influenced by parameters like oxidative stress, pH or viscosity. Besides metabolism, oxygen levels and consumption has to be taken into account in order to understand treatment responses. For this, correlated imaging of phosphorescence and fluorescence lifetime parameters has been investigated by us and used to observe metabolic markers simultaneously with oxygen concentrations. The technique is based on time correlated single photon counting to detect the fluorescence lifetime of NAD(P)H and FAD by FLIM and the phosphorescence lifetime of newly developed phosphors and photosensitizers by PLIM. For this, the photosensitizer TLD1433 from Theralase, which is based on a ruthenium (II) coordination complex, was used. TLD1433 which acts as a redox indicator was mainly found in cytoplasmatic organelles. The most important observation was that TLD1433 can be used as a phosphor to follow up local oxygen concentration and consumption during photodynamic therapy. Oxygen consumption was accompanied by a change in cell metabolism, observed by simultaneous FLIM/PLIM. The combination of autofluorescence-FLIM and phosphor-PLIM in luminescence lifetime microscopy provides new insights in light induced reactions.

Improved urban stormwater treatment and pollutant removal pathways in amended wet detention ponds.

PubMed

Istenič, Darja; Arias, Carlos A; Vollertsen, Jes; Nielsen, Asbjørn H; Wium-Andersen, Tove; Hvitved-Jacobsen, Thorkild; Brix, Hans

2012-01-01

Dissolved and colloidal bound pollutants are generally poorly removed from stormwater in wet detention ponds. These fractions are, however, the most bio-available, and therefore three wet detention ponds were amended with planted sand filters, sorption filters and addition of precipitation chemicals to enhance the removal of dissolved pollutants and pollutants associated with fine particles and colloids. The three systems treated runoff from industrial, residential and combined (residential and highway) catchments and had permanent volumes of 1,990, 6,900 and 2,680 m(3), respectively. The treatment performance of the ponds for elimination of total suspended solids (TSS), total nitrogen (Tot-N), total phosphorous (Tot-P), PO(4)-P, Pb, Zn, Cd, Ni, Cr, Cu, Hg were within the range typically reported for wet detention ponds, but the concentrations of most of the pollutants were efficiently reduced by the planted sand filters at the outlets. The sorption filters contributed to further decrease the concentration of PO(4)-P from 0.04 ± 0.05 to 0.01 ± 0.01 mg L(-1) and were also efficient in removing heavy metals. Dosing of iron sulphate to enrich the bottom sediment with iron and dosing of aluminium salts to the inlet water resulted in less growth of phytoplankton, but treatment performance was not significantly affected. Heavy metals (Pb, Zn, Cd, Ni, Cr and Cu) accumulated in the sediment of the ponds. The concentrations of Zn, Ni, Cu and Pb in the roots of the wetland plants were generally correlated to the concentrations in the sediments. Among 13 plant species investigated, Rumex hydrolapathum accumulated the highest concentrations of heavy metals in the roots (Concentration Factor (CF) of 4.5 and 5.9 for Zn and Ni, respectively) and Iris pseudacorus the lowest (CF < 1). The translocation of heavy metals from roots to the aboveground tissues of plants was low. Therefore the potential transfer of heavy metals from the metal-enriched sediment to the surrounding ecosystem via plant uptake and translocation is negligible.

46 CFR 151.50-23 - Phosphoric acid.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Phosphoric acid. 151.50-23 Section 151.50-23 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-23 Phosphoric acid. (a) The term phosphoric acid as used in this subpart shall include, in addition to phosphoric acid, aqueous solutions of...

46 CFR 151.50-23 - Phosphoric acid.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Phosphoric acid. 151.50-23 Section 151.50-23 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-23 Phosphoric acid. (a) The term phosphoric acid as used in this subpart shall include, in addition to phosphoric acid, aqueous solutions of...

Preparation of balanced trichromatic white phosphors for solid-state white lighting.

PubMed

Al-Waisawy, Sara; George, Anthony F; Jadwisienczak, Wojciech M; Rahman, Faiz

2017-08-01

High quality white light-emitting diodes (LEDs) employ multi-component phosphor mixtures to generate light of a high color rendering index (CRI). The number of distinct components in a typical phosphor mix usually ranges from two to four. Here we describe a systematic experimental technique for starting with phosphors of known chromatic properties and arriving at their respective proportions for creating a blended phosphor to produce light of the desired chromaticity. This method is applicable to both LED pumped and laser diode (LD) pumped white light sources. In this approach, the radiometric power in the down-converted luminescence of each phosphor is determined and that information is used to estimate the CIE chromaticity coordinate of light generated from the mixed phosphor. A suitable method for mixing multi-component phosphors is also described. This paper also examines the effect of light scattering particles in phosphors and their use for altering the spectral characteristics of LD- and LED-generated light. This is the only approach available for making high efficiency phosphor-converted single-color LEDs that emit light of wide spectral width. Copyright © 2016 John Wiley & Sons, Ltd.

RAPID AND PRECISE METHOD FOR MEASURING STABLE CARBON ISOTOPE RATIOS OF DISSOLVED INORGANIC CARBON

EPA Science Inventory

We describe a method for rapid preparation, concentration and stable isotopic analysis of dissolved inorganic carbon (d13C-DIC). Liberation of CO2 was accomplished by placing 100 ?l phosphoric acid and 0.9 ml water in an evacuated 1.7-ml gas chromatography (GC) injection vial. Fo...

Luminescence properties of europium?terbium double activated calcium tungstate phosphor*1

NASA Astrophysics Data System (ADS)

Nazarov, M. V.; Jeon, D. Y.; Kang, J. H.; Popovici, E.-J.; Muresan, L.-E.; Zamoryanskaya, M. V.; Tsukerblat, B. S.

2004-08-01

Double incorporation of Eu 3+ and Tb 3+ ions into a CaWO 4 crystalline lattice modifies the luminescence spectrum due to the formation of new emission centers. Depending on the activators concentration and nature, as well as on the interaction between the activators themselves, the luminescence color can be varied within the entire range of the visible spectrum. Variable luminescence was obtained when CaWO 4:Eu,Tb phosphors with 0-5 mol% activator ions were exposed to relatively low excitation energies as UV (365 and 254 nm). Under high energy excitation such as VUV (147 nm) radiation or electron beam, white light has been observed. This material with controlled properties seems to be promising for the applications in fluorescent lamps, colored lightning for advertisement industries, and other optoelectronic devices.

Two-step fabrication of ZnO-PVP composites with tunable visible emissions

NASA Astrophysics Data System (ADS)

Agulto, Verdad C.; Empizo, Melvin John F.; Kawano, Keisuke; Minami, Yuki; Yamanoi, Kohei; Sarukura, Nobuhiko; Yago, Allan Christopher C.; Sarmago, Roland V.

2018-02-01

We report a two-step fabrication of zinc oxide-polyvinylpyrrolidone (ZnO-PVP) composites for potential phosphor-based applications. The composites are fabricated by initially preparing ZnO microrods using hydrothermal growth method and then dip-coating the microrods into aqueous PVP solutions with varying molar concentrations. The as-prepared ZnO microrods exhibit smooth surfaces and broad visible emissions, while the ZnO-PVP composites have pitted surfaces with shifted and reduced visible emissions. These changes in the structural and optical properties, which are found to depend on the PVP concentration, are attributed to the adsorption of PVP on the microrod surface. Although the surface morphology and visible emission are modified by PVP, the composites still maintain a hexagonal wurtzite crystal structure and near-band-edge ultraviolet (UV) emission similar with the as-prepared microrods. Our results therefore suggest that the ZnO-PVP composites can be used as phosphors that offer not only properties found in both ZnO and PVP but also tunable visible emissions which can be controlled during material fabrication.

Thermoluminescence response of rare earth activated zinc lithium borate glass

NASA Astrophysics Data System (ADS)

Saidu, A.; Wagiran, H.; Saeed, M. A.; Obayes, H. K.; Bala, A.; Usman, F.

2018-03-01

New glasses of zinc lithium borate doped with terbium oxide were synthesized by high temperature solid-state reaction. The amorphous nature of the glasses was confirmed using x-ray diffraction analysis (XRD). Thermoluminescence (TL) response of pure zinc lithium borate (ZLB) and zinc lithium borate doped with terbium (ZLB: Tb) exposed to gamma radiation was measured and compared. There is significant enhancement in the TL yields of ZLB: Tb compared to that of pure ZLB. Effect of varying concentration of dopant (Tb4O7) on the TL response of zinc lithium borate was investigated. 0.3 mol% concentration of Tb exhibited strongest TL intensity. Thermoluminescence curve of the phosphor consist of single isolated peak. The TL response of the new materials to the exposed radiation is linear within 0.5-100 Gy range of dose with sublinearity at the lower region of the curve. High sensitivity was exhibited by the new amorphous materials. Reproducibility, thermal fading and energy response of the proposed TLD were investigated and shows remarkable result that made the phosphor suitable for radiation dosimetry.

Pretreating wheat straw by phosphoric acid plus hydrogen peroxide for enzymatic saccharification and ethanol production at high solid loading.

PubMed

Qiu, Jingwen; Ma, Lunjie; Shen, Fei; Yang, Gang; Zhang, Yanzong; Deng, Shihuai; Zhang, Jing; Zeng, Yongmei; Hu, Yaodong

2017-08-01

Wheat straw was pretreated by phosphoric acid plus hydrogen peroxide (PHP) for enzymatic hydrolysis and ethanol fermentation at high solid loadings. Results indicated solid loading could reach 20% with 77.4% cellulose-glucose conversion and glucose concentration of 164.9g/L in hydrolysate, it even was promoted to 25% with only 3.4% decrease on cellulose-glucose conversion as the pretreated-wheat straw was dewatered by air-drying. 72.9% cellulose-glucose conversion still was achieved as the minimized enzyme input of 20mg protein/g cellulose was employed for hydrolysis at 20% solid loading. In the corresponding conditions, 100g wheat straw can yield 11.2g ethanol with concentration of 71.2g/L by simultaneous saccharification and fermentation. Thus, PHP-pretreatment benefitted the glucose or ethanol yield at high solid loadings with lower enzyme input. Additionally, decreases on the maximal cellulase adsorption and the direct-orange/direct-blue indicated drying the PHP-pretreated substrates negatively affected the hydrolysis due to the shrinkage of cellulase-size-accommodable pores. Copyright © 2017 Elsevier Ltd. All rights reserved.

Low thermal budget n-type doping into Ge(001) surface using ultraviolet laser irradiation in phosphoric acid solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takahashi, Kouta, E-mail: ktakahas@alice.xtal.nagoya-u.ac.jp, E-mail: kurosawa@alice.xtal.nagoya-u.ac.jp; Sakashita, Mitsuo; Takeuchi, Wakana

2016-02-01

We have investigated phosphorus (P) doping into Ge(001) surfaces by using ultraviolet laser irradiation in phosphoric acid solution at room temperature. We demonstrated that the diffusion depth of P in Ge and the concentration of electrically activated P can be controlled by the number of laser shots. Indeed, a high concentration of electrically activated P of 2.4 × 10{sup 19} cm{sup −3} was realized by 1000-times laser shots at a laser energy of 1.0 J/cm{sup 2}, which is comparable or better than the counterparts of conventional n-type doping using a high thermal budget over 600 °C. The generation current is dominant in the reverse biasmore » condition for the laser-doped pn-junction diodes independent on the number of laser shots, thus indicating low-damage during the pn-junction formation. These results open up the possibility for applicable low thermal budget doping process for Ge-based devices fabricated on flexible substrates as well as Si electronics.« less

Phosphoric acid activation of sugarcane bagasse for removal of o-toluidine and benzidine

NASA Astrophysics Data System (ADS)

Adib, M. R. M.; Attahirah, M. H. M. N.; Amirza, A. R. M.

2018-04-01

In the effort to find alternatives for low cost adsorbent, activated carbon using sugarcane bagasse (SBAC) has been introduced in this study that has undergo chemical treatment using phosphoric acid to determine the effectiveness of adsorption process in removing o-toluidine and benzidine. Throughout this study, 92.9% of o-toluidine has been successfully removed by SBAC at optimum value of 1.1 g of dosage with contact time of 10 minutes and concentration of 10 mg/L. While benzidine was remove by 83.1% at optimum dosage of 1.1 g with 60 minutes of contact time and at 20 mg/L concentrations. Testing of SEM proves that SBAC has high porosity and comparable to CAC. In FTIR results, shows that CAC has high number of double bond while SBAC shows no double bond at all. Presence of double bond in CAC lead to increase in percentage of removal of adsorbate. After considering other factor such as cost, energy and environmental friendly, it shows that SBAC was considerable to replaced CAC.

Phytase modulates ileal microbiota and enhances growth performance of the broiler chickens.

PubMed

Ptak, Anna; Bedford, Michael R; Świątkiewicz, Sylwester; Żyła, Krzysztof; Józefiak, Damian

2015-01-01

Phytase is well studied and explored, however, little is known about its effects on the microbial ecology of the gastrointestinal tract. In total, 400 one-day-old female Ross 308 chicks were randomly distributed to four experimental groups. The dietary treatments were arranged as a 2 × 2 complete factorial design, with the factors being adequate (PC) or insufficient calcium (Ca) and digestible phosphor (dP)(NC) and with or without 5000 phytase units (FTU)/kg of Escherichia coli 6-phytase. The gastrointestinal tract pH values, ileal microbial communities and short-chain fatty acid concentrations in the digesta were determined. The reduction in Ca and dP concentration significantly affected pH in the crop and caeca, and addition of phytase to the NC resulted in a pH increase in the ileum. The reduction in Ca and dP concentration significantly lowered, while phytase supplementation increased ileal total bacterial counts. Additionally, the deficient diet reduced butyrate- but increased lactate-producing bacteria. The addition of phytase increased Lactobacillus sp./Enterococcus sp. whereas in case of Clostridium leptum subgroup, Clostridium coccoides-Eubacterium rectale cluster, Bifidobacterium sp. and Streptococcus/Lactococcus counts, a significant Ca and dP level x phytase interaction was found. However, the recorded interactions indicated that the effects of phytase and Ca and dP levels were not consistent. Furthermore, the reduction of Ca and dP level lowered Clostridium perfringens and Enterobacteriaceae counts. The analysis of fermentation products showed that reducing the Ca and dP content in the diet reduced total SCFA, DL-lactate, and acetic acid in the ileum whereas phytase increased concentrations of these acids in the NC group. This suggests that P is a factor which limits fermentation in the ileum. It may be concluded that phytase plays a role in modulating the gut microbiota of chicken, however, this is clearly linked with the levels of P and Ca in a diet.

Phytase Modulates Ileal Microbiota and Enhances Growth Performance of the Broiler Chickens

PubMed Central

Ptak, Anna; Bedford, Michael R.; Świątkiewicz, Sylwester; Żyła, Krzysztof; Józefiak, Damian

2015-01-01

Phytase is well studied and explored, however, little is known about its effects on the microbial ecology of the gastrointestinal tract. In total, 400 one-day-old female Ross 308 chicks were randomly distributed to four experimental groups. The dietary treatments were arranged as a 2 × 2 complete factorial design, with the factors being adequate (PC) or insufficient calcium (Ca) and digestible phosphor (dP)(NC) and with or without 5000 phytase units (FTU)/kg of Escherichia coli 6-phytase. The gastrointestinal tract pH values, ileal microbial communities and short-chain fatty acid concentrations in the digesta were determined. The reduction in Ca and dP concentration significantly affected pH in the crop and caeca, and addition of phytase to the NC resulted in a pH increase in the ileum. The reduction in Ca and dP concentration significantly lowered, while phytase supplementation increased ileal total bacterial counts. Additionally, the deficient diet reduced butyrate- but increased lactate-producing bacteria. The addition of phytase increased Lactobacillus sp./Enterococcus sp. whereas in case of Clostridium leptum subgroup, Clostridium coccoides - Eubacterium rectale cluster, Bifidobacterium sp. and Streptococcus/Lactococcus counts, a significant Ca and dP level x phytase interaction was found. However, the recorded interactions indicated that the effects of phytase and Ca and dP levels were not consistent. Furthermore, the reduction of Ca and dP level lowered Clostridium perfringens and Enterobacteriaceae counts. The analysis of fermentation products showed that reducing the Ca and dP content in the diet reduced total SCFA, DL-lactate, and acetic acid in the ileum whereas phytase increased concentrations of these acids in the NC group. This suggests that P is a factor which limits fermentation in the ileum. It may be concluded that phytase plays a role in modulating the gut microbiota of chicken, however, this is clearly linked with the levels of P and Ca in a diet. PMID:25781608

Blue-green phosphor for fluorescent lighting applications

DOEpatents

Srivastava, Alok; Comanzo, Holly; Manivannan, Venkatesan; Setlur, Anant Achyut

2005-03-15

A fluorescent lamp including a phosphor layer including Sr.sub.4 Al.sub.14 O.sub.25 :Eu.sup.2+ (SAE) and at least one of each of a red, green and blue emitting phosphor. The phosphor layer can optionally include an additional, deep red phosphor and a yellow emitting phosphor. The resulting lamp will exhibit a white light having a color rendering index of 90 or higher with a correlated color temperature of from 2500 to 10000 Kelvin. The use of SAE in phosphor blends of lamps results in high CRI light sources with increased stability and acceptable lumen maintenance over, the course of the lamp life.

Influence of iron precipitated condition and light intensity on microalgae activated sludge based wastewater remediation.

PubMed

Anbalagan, Anbarasan; Schwede, Sebastian; Lindberg, Carl-Fredrik; Nehrenheim, Emma

2017-02-01

The indigenous microalgae-activated sludge (MAAS) process during remediation of municipal wastewater was investigated by studying the influence of iron flocculation step and light intensity. In addition, availability of total phosphorous (P) and photosynthetic activity was examined in fed-batch and batch mode under northern climatic conditions and limited lighting. This was followed by a semi-continuous operation with 4 d of hydraulic retention time and mean cell residence time of 6.75 d in a photo-bioreactor (PBR) with varying P availability. The fed-batch condition showed that P concentrations of 3-4 mg L -1 were effective for photosynthetic chl. a development in iron flocculated conditions. In the PBR, the oxygen evolution rate increased with increase in the concentration of MAAS (from 258 to 573 mg TSS L -1 ) at higher surface photosynthetic active radiation (250 and 500 μmol m -2 s -1 ). Additionally, the rate approached a saturation phase at low MAAS (110 mg L -1 ) with higher light intensities. Semi-continuous operation with luxury P uptake and effective P condition showed stable average total nitrogen removal of 88 and 92% respectively, with residual concentrations of 3.77 and 2.21 mg L -1 . The corresponding average P removal was 68 and 59% with residual concentrations of 2.32 and 1.75 mg L -1 . The semi-continuous operation produced a rapidly settleable MAAS under iron flocculated condition with a settling velocity of 92-106 m h -1 and sludge volume index of 31-43 ml g -1 in the studied cases. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improvement of the performance of the positive electrode in the lead/acid battery by addition of boric acid

NASA Astrophysics Data System (ADS)

Badawy, W. A.; El-Egamy, S. S.

A major disadvantage of the lead/acid battery is the decrease in voltage during operation which makes it unsuitable for systems sensitive to voltage fluctuations. Additives like BaSO 4 or SrSO 4, which are isomorphous to PbSO 4, have been used to overcome this problem. Phosphoric acid and the various phosphates have long been used to improve the performance of the positive electrode of the battery. A beneficial effect of phosphoric acid is to inhibit the rate of the self-discharge reaction of the positive electrode in the lead/acid battery. However, adverse effects of phosphoric acid include capacity loss in the initial cycles, excessive mossing, especially at high H 3PO 4 concentrations, and poor low-temperature performance (decrease in the rate of PbSO 4 oxidation). The effect of boric acid as an additive substituting for H 3PO 4 has been investigated using linear sweep voltammetry, constant potential and impedance measurements. The results show that boric acid markedly improves the kinetics of the {PbO 2}/{PbSO 4} couple and removes the problems encountered during the usage of H 3PO 4.

Enhancing the photovoltaic performance of CdTe/CdS solar cell via luminescent downshifting using K{sub 2}SiF{sub 6}:Mn{sup 4+} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Talewar, R. A., E-mail: talewarrupesh@gmail.com; Joshi, C. P.; Moharil, S. V.

2016-05-23

The efficiency of CdTe/CdS solar cell can be significantly improved by using luminescent down-shifting material on their front surface. Taking this into account a red emitting phosphor K{sub 2}Si{sub 1-x}F{sub 6}:xMn{sup 4+} (x=10 to 25 mol %) has been synthesized through wet chemical method. The as-synthesized materials were characterized by powder x-ray diffraction (XRD) and photoluminescence (PL) techniques. The photoluminescence studies of K{sub 2}SiF{sub 6}:Mn{sup 4+} revealed enhancement in the emission intensity, when Mn{sup 4+} concentration was increased from 10 mol % to 25 mol %. This red emitting phosphor efficiently absorbs the photons typically in the region 300-500 nmmore » and re-emits in the region where the photovoltaic device exhibits significantly better response. The results show the possibility of enhancing the photovoltaic conversion efficiency of CdTe thin film solar cell by modifying the absorption spectra and utilising the energy in the UV-blue part of the solar spectrum.« less

Nationwide Distribution of Per- and Polyfluoroalkyl Substances in Outdoor Dust in Mainland China From Eastern to Western Areas.

PubMed

Yao, Yiming; Sun, Hongwen; Gan, Zhiwei; Hu, Hongwei; Zhao, Yangyang; Chang, Shuai; Zhou, Qixing

2016-04-05

From eastern to western areas, per- and polyfluoroalkyl substances (PFASs) were detected at substantial levels in the outdoor dust across mainland China. Urban samples generally showed higher levels compared with those of rural samples. Compared with neutral PFASs, ionizable PFASs (C4-C12 perfluoroalkyl carboxylic acids and C4/C8 perfluoroalkyl sulfonic acids) were more abundant, with the highest total concentration up to 1.6 × 10(2) ng/g and perfluorooctanoic acid (PFOA) being a predominant analogue. Fluorotelomer alcohols (FTOHs) and polyfluoroalkyl phosphoric acid diesters (DiPAPs) were both detected in most samples with total concentrations of 0.12-32 and 0.030-20 ng/g, respectively. Perfluorooctane sulfonamidoethanols/sulfonamides (FOSE/As) were detected at low frequencies (<30%). In addition to partitioning to organic moiety, specific adsorption onto mineral particles can be important for PFASs to bind onto outdoor dust, especially for short-chain ionizable PFASs. The eastern plain areas were characterized by a higher contribution of long-chain ionizable PFASs; whereas the western high plateau areas were characterized by the dominating contribution of short-chain analogues. The difference suggests that the long-range atmospheric transport potential of PFASs from source regions to the inland is probably limited by the increase in altitude, and different sources from adjacent regions may influence the western border area of China.

Soil, Leaf and Root Ecological Stoichiometry of Caragana korshinskii on the Loess Plateau of China in Relation to Plantation Age

PubMed Central

Zeng, Quanchao; Lal, Rattan; Chen, Yanan; An, Shaoshan

2017-01-01

Caragana korshinskii, a leguminous shrub, a common specie, is widely planted to prevent soil erosion on the Loess Plateau. The objective of this study was to determine how the plantation ages affected soil, leaf and root nutrients and ecological stoichiometry. The chronosequence ages of C. korshinskii plantations selected for this study were 10, 20 and 30 years. Soil organic carbon (SOC) and soil total nitrogen (STN) of C. korshinskii plantations significantly increased with increase in the chronosequence age. However, soil total phosphorous (STP) was not affected by the chronosequence age. The soil C: N ratio decreased and the soil C: P and N: P ratios increased with increasing plantation age. The leaf and root concentrations of C, N, and P increased and the ratios C: N, C: P, and N: P decreased with age increase. Leaf N: P ratios were >20, indicating that P was the main factor limiting the growth of C. korshinskii. This study also demonstrated that the regeneration of natural grassland (NG) effectively preserved and enhanced soil nutrient contents. Compared with NG, shrub lands (C. korshinskii) had much lower soil nutrient concentrations, especially for long (>20 years) chronosequence age. Thus, the regeneration of natural grassland is an ecologically beneficial practice for the recovery of degraded soils in this area. PMID:28076357

Per- and poly-fluoroalkyl substances (PFASs) in the urban, industrial, and background atmosphere of Northeastern China coast around the Bohai Sea: Occurrence, partitioning, and seasonal variation

NASA Astrophysics Data System (ADS)

Yao, Yiming; Chang, Shuai; Zhao, Yangyang; Tang, Jianhui; Sun, Hongwen; Xie, Zhiyong

2017-10-01

Air samples were collected using high-volume samplers at two coastal towns on the Bohai Sea in China, 320 km apart, and at a background site (North Huangcheng Island) in the Bohai Sea, 50 km from the coast. A suite of neutral and ionic per- and poly-fluoroalkyl substances (PFASs) was investigated. Urban activity was related to high levels of neutral PFASs at Tianjin while perfluorooctanoic carboxylic acid (PFOA) was dominant in the atmosphere at Weifang, possibly due to industrial sources. Polyfluoroalkyl phosphoric acid diesters (diPAPs) occurred in the particle phase only, with a total concentration range of 0.02-6.72 pg m-3. The dominant homologue was 6:2 diPAP. PFASs profiles at NHI suggested direct atmospheric transport of neutral and ionic PFASs from source regions. Temperature-dependent partitioning of fluorotelomer alcohols (FTOHs) was observed in winter, when total concentrations and particle-phase fractions of FTOHs were significantly higher as compared to those in summer. Correlation analyses suggested more active gas-phase degradation of FTOHs in summer and likely heterogeneous degradation in both seasons. Overall, it is necessary to account for ionic PFASs in both gas and particle phases and particulate matter was important for atmospheric transport and for determining the fate of PFASs, especially in areas close to a source region.

A colloidal quantum dot photonic crystal phosphor: nanostructural engineering of the phosphor for enhanced color conversion.

PubMed

Min, Kyungtaek; Jung, Hyunho; Park, Yeonsang; Cho, Kyung-Sang; Roh, Young-Geun; Hwang, Sung Woo; Jeon, Heonsu

2017-06-29

Phosphors, long-known color-converting photonic agents, are gaining increasing attention owing to the interest in white LEDs and related applications. Conventional material-based approaches to phosphors focus on obtaining the desired absorption/emission wavelengths and/or improving quantum efficiency. Here, we report a novel approach for enhancing the performance of phosphors: structural modification of phosphors. We incorporated inorganic colloidal quantum dots (CQDs) into a lateral one-dimensional (1D) photonic crystal (PhC) thin-film structure, with its photonic band-edge (PBE) modes matching the energy of 'excitation photons' (rather than 'emitted photons', as in most other PBE application devices). At resonance, we observed an approximately 4-fold enhancement of fluorescence over the reference bulk phosphor, which reflects an improved absorption of the excitation photons. This nano-structural engineering approach is a paradigm shift in the phosphor research area and may help to develop next-generation higher efficiency phosphors with novel characteristics.

Up-conversion luminescence properties and energy transfer of Tm{sup 3+}/Yb{sup 3+} co-doped BaLa{sub 2}ZnO{sub 5}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Jing; Mei, Lefu, E-mail: mlf@cugb.edu.cn; Deng, Junru

2015-11-15

Tm{sup 3+}/Yb{sup 3+} co-doped BaLa{sub 2}ZnO{sub 5} up-conversion (UC) phosphors were successfully synthesized by high temperature solid-state reaction method. The X-ray diffraction (XRD) results show that synthesized phosphor co-doped with 0.75% Tm/10% Yb has the optimum pure phase of BaLa{sub 2}ZnO{sub 5} among different co-doping concentrations. The structure of BaLa{sub 2}ZnO{sub 5}:0.75% Tm/10% Yb phosphor was refined by the Rietveld method and results show the decreased unit cell parameters and cell volume after doping Tm{sup 3+}/Yb{sup 3+}, indicating that Tm{sup 3+}/Yb{sup 3+} have successfully replaced La{sup 3+}. Under excitation at 980 nm, Tm{sup 3+}/Yb{sup 3+} co-doped BaLa{sub 2}ZnO{sub 5} phosphorsmore » present bright blue emission near 478 nm generated by the {sup 1}G{sub 4}→{sup 3}H{sub 6} transition and weak red emissions around 653 nm and 692 nm generated by the {sup 1}G{sub 4}→{sup 3}F{sub 4} and {sup 3}F{sub 3}→{sup 3}H{sub 6} transitions of Tm{sup 3+}, respectively. The UC luminescence properties of BaLa{sub 2}ZnO{sub 5} phosphors co-doped with different Tm{sup 3+}/Yb{sup 3+} concentrations were investigated, and the related UC mechanisms of Tm{sup 3+}/Yb{sup 3+} co-doped BaLa{sub 2}ZnO{sub 5} depending on pump power were studied in detail. - Graphical abstract: Up-conversion luminescence of BaLa{sub 2}ZnO{sub 5}:Tm{sup 3+}/Yb{sup 3+} and its crystal structure and up-conversion mechanisms. - Highlights: • Up-conversion phosphors BaLa{sub 2}ZnO{sub 5} co-doped with Tm{sup 3+}/Yb{sup 3+} were synthesized by high temperature solid-state reaction method. • The crystal structure of BaLa{sub 2}ZnO{sub 5} and the changes of cell parameters and volume of BaLa{sub 2}ZnO{sub 5} after doping Tm{sup 3+} and Yb{sup 3+} have been discussed. • Up-conversion luminescence properties and energy transfer between Tm{sup 3+} and Yb{sup 3+} in BaLa{sub 2}ZnO{sub 5} have been discussed in detail.« less

Spectral properties of Dy3+ doped ZnAl2O4 phosphor

NASA Astrophysics Data System (ADS)

Prakash, Ram; Kumar, Sandeep; Mahajan, Rubby; Khajuria, Pooja; Kumar, Vinay; Choudhary, R. J.; Phase, D. M.

2018-05-01

Herein, Dy3+ doped ZnAl2O4 phosphor was synthesized by the solution combustion method. The synthesized phosphor was characterized by X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, UV-Vis spectroscopy and X-ray photoelectron spectroscopy (XPS). The phase purity of the phosphor was confirmed by the XRD studies that showed cubic symmetry of the synthesized phosphor. Under UV excitation (388 nm) the PL emission spectrum of the phosphor shows characteristic transition from the Dy3+ ion. A band gap of 5.2 eV was estimated from the diffused reflectance spectroscopy. The surface properties of the phosphor were studied using the X-ray photoelectron spectroscopy.

Phosphors with long-persistent green phosphorescence

DOEpatents

Yen, William M; Jia, Weiyi; Lu, Lizhu; Yuan, Huabiao

2001-01-01

This invention relates to phosphors including long-persistence green phosphors. Phosphors of the invention are represented by the general formula: M.sub.k Al.sub.2 O.sub.4 :2xEu.sup.2+,2yR.sup.3+ wherein k-1-2x-2y, x is a number ranging from about 0.0001 to about 0.05, y is a number ranging from about x to about 3x, M is an alkaline earth metal, and R.sup.3+ is one or more trivalent metal ions. Phosphors of this invention include powders, ceramics, single crystals and single crystal fibers. A method of manufacturing improved phosphors and a method of manufacturing single crystal phosphors are also provided.

Temperature Sensing Above 1000 C Using Cr-Doped GdAlO3 Spin-Allowed Broadband Luminescence

NASA Technical Reports Server (NTRS)

Eldridge, Jeffrey I.; Chambers, Matthew D.

2012-01-01

Cr-doped GdAlO3 (Cr:GdAlO3) is shown to produce remarkably high-intensity spin-allowed broadband luminescence with sufficiently long decay times to make effective luminescence-decay-time based temperature measurements above 1000 C. This phosphor is therefore an attractive alternative to the much lower luminescence intensity rare-earth-doped thermographic phosphors that are typically utilized at these elevated temperatures. In particular, Cr:GdAlO3 will be preferred over rare-earth-doped phosphors, such as Dy:YAG, at temperatures up to 1200 C for intensity-starved situations when the much lower emission intensity from rare-earth-doped phosphors is insufficient for accurate temperature measurements in the presence of significant radiation background. While transition-metal-doped phosphors such as Cr:Al2O3 (ruby) are known to exhibit high luminescence intensity at low dopant concentrations, quenching due to nonradiative decay pathways competing with the (sup 2)E to (sup 4)A(sub 2) radiative transition (R line) has typically restricted their use for temperature sensing to below 600 C. Thermal quenching of the broadband (sup 4)T(sub 2) to (sup 4)A(sub 2) radiative transition from Cr:GdAlO3, however, is delayed until much higher temperatures (above 1000 C). This spin-allowed broadband emission persists to high temperatures because the lower-lying (sup 2)E energy level acts as a reservoir to thermally populate the higher shorter-lived (sup 4)T(sub 2) energy level and because the activation energy for nonradiative crossover relaxation from the (sup 4)T(sub 2) level to the (sup 4)A(sub 2) ground state is high. The strong crystal field associated with the tight bonding of the AlO6 octahedra in the GdAlO3 perovskite structure is responsible for this behavior.

Color-tunable up-conversion emission from Yb{sup 3+}/Er{sup 3+}/Tm{sup 3+} tri-doped T-AgGd(W,Mo){sub 2}O{sub 8} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jijian; Liu, Ni; Xu, Ling, E-mail: xuling@snnu.edu.cn

Graphical abstract: The doping ions tune the UC luminescence of the T- AgGd(W,Mo){sub 2}O{sub 8}:Yb{sup 3+}/Er{sup 3+}/Tm{sup 3+} material. - Highlights: • AgGd(W,Mo){sub 2}O{sub 8}:Yb{sup 3+}/Er{sup 3+}/Tm{sup 3+} phosphors show color-tunable blue, green, and red UC emissions. • The samples’ UC emission color can be switched with the concentrations of doped ions. • The blue, green and red UC mechanisms are interpreted reasonably as three- and two- photon process. - Abstract: Tetragonal Yb{sup 3+}/Er{sup 3+}/Tm{sup 3+} tri-doped AgGd(W,Mo){sub 2}O{sub 8} phosphors were prepared by the high-temperature solid-state method. When the phosphors were excited at 980 nm, the UC emission ofmore » blue at 475 nm, green at 525 and 550 nm, and red at 656 nm were corresponding to the {sup 1}G{sub 4} → {sup 3}H{sub 6} transition of Tm{sup 3+} ions, the {sup 2}H{sub 11/2},{sup 4}S{sub 3/2} → {sup 4}I{sub 15/2} transitions of Er{sup 3+} ions, and the {sup 4}F{sub 9/2} → {sup 4}I{sub 15/2} transition of Er{sup 3+} ions, respectively. The blue UC emissions originate from a three-photon mechanism, while the green and red ones of Er{sup 3+} from two-photon process. The UC emission color of the Yb{sup 3+}/Er{sup 3+}/Tm{sup 3+} tri-doped AgGdW{sub 2}O{sub 8} samples switched from green to white, and then to red depending on the concentrations of Er{sup 3+} and Tm{sup 3+}. After doping with Mo(VI), tetragonal AgGdW{sub 2}O{sub 8} was transformed into tetragonal AgGdMo{sub 2}O{sub 8}, resulting in a slightly enhanced UC luminescence intensity with the favor of the red emission of Er{sup 3+} ion.« less

Physical and chemical characteristics of lakes across heterogeneous landscapes in arctic and subarctic Alaska

NASA Astrophysics Data System (ADS)

Larsen, A. S.; O'Donnell, J. A.; Schmidt, J. H.; Kristenson, H. J.; Swanson, D. K.

2017-04-01

Lakes are an important component of high-latitude regions, providing habitat for fish and wildlife and playing a critical role in biogeochemical and global carbon cycles. High-latitude lakes are sensitive to climate change, in part due to their development within permafrost soils. Considerable heterogeneity exists across arctic and subarctic landscapes, yet little is known about how this landscape variability influences chemical and physical attributes of lakes. We investigated the physical and chemical limnology of 617 lakes in Alaska's boreal forest and boreal-arctic transition zone. We categorized lakes into 10 basin types based on parent material, topography, genesis, and permafrost characteristics. Physical parameters varied across lake basin types, with the deepest lakes occurring in ice-poor glacial deposits and ice-rich terrain, while the shallowest lakes were observed in floodplain deposits and coastal lowlands. Dissolved inorganic nitrogen (N) and phosphorous (P) concentrations were generally low across all landscapes, whereas total N and P were highest in lakes underlain by ice-rich Pleistocene loess. Total N and P concentrations were significantly correlated with chlorophyll a, indicating a possible colimitation of primary productivity in these systems. Base cation concentrations helped elucidate lake basin hydrology and the relative influence of shallow versus deep groundwater inputs to surface water. Using these results, we developed a simple conceptual model for each lake and landscape type based on differences in physical and chemical parameters. Overall, we expect that the vulnerability of lake ecosystems to climate change will vary across lake basin types and will be mediated by spatial patterns in permafrost characteristics and subsurface hydrology.

APEX simulation of runoff and total phosphorous for three adjacent row-crop watersheds with claypan soils

USDA-ARS?s Scientific Manuscript database

The Agricultural Policy Environmental Extender (APEX) model can simulate crop yields, runoff, and the transport of sediment and nutrients in small watersheds that have combinations of farm level landscapes, cropping systems and/or management practices. The objectives of the study were to parameteri...

URANIUM COMPOSITIONS

DOEpatents

Allen, N.P.; Grogan, J.D.

1959-05-12

This patent relates to high purity uranium alloys characterized by improved stability to thermal cycling and low thermal neutron absorption. The high purity uranium alloy contains less than 0.1 per cent by weight in total amount of any ore or more of the elements such as aluminum, silicon, phosphorous, tin, lead, bismuth, niobium, and zinc.

Depth-Penetrating Measurements Developed for Thermal Barrier Coatings Incorporating Thermographic Phosphors

NASA Technical Reports Server (NTRS)

Eldridge, Jeffrey I.; Bencic, Timothy J.

2004-01-01

The insulating properties of thermal barrier coatings (TBCs) provide highly beneficial thermal protection to turbine engine components by reducing the temperature sustained by those components. Therefore, measuring the temperature beneath the TBC is critical for determining whether the TBC is performing its insulating function. Currently, noncontact temperature measurements are performed by infrared pyrometry, which unfortunately measures the TBC surface temperature rather than the temperature of the underlying component. To remedy this problem, the NASA Glenn Research Center, under the Information Rich Test Instrumentation Project, developed a technique to measure the temperature beneath the TBC by incorporating a thin phosphor layer beneath the TBC. By performing fluorescence decay-time measurements on light emission from this phosphor layer, Glenn successfully measured temperatures from the phosphor layer up to 1100 C. This is the first successful demonstration of temperature measurements that penetrate beneath the TBC. Thermographic phosphors have a history of providing noncontact surface temperature measurements. Conventionally, a thermographic phosphor is applied to the material surface and temperature measurements are performed by exciting the phosphor with ultraviolet light and then measuring the temperature-dependent decay time of the phosphor emission at a longer wavelength. The innovative feature of the new approach is to take advantage of the relative transparency of the TBC (composed of yttria-stabilized zirconia) in order to excite and measure the phosphor emission beneath the TBC. The primary obstacle to achieving depth-penetrating temperature measurements is that the TBCs are completely opaque to the ultraviolet light usually employed to excite the phosphor. The strategy that Glenn pursued was to select a thermographic phosphor that could be excited and emit at wavelengths that could be transmitted through the TBC. The phosphor that was selected was yttria doped with europia (Y2O3:Eu), which has a minor excitation peak at 532 nm (green) and an emission peak at 611 nm (red)--both are wavelengths that exhibit significant transmission through the TBC. The measurements were performed on specimens consisting of a 25- m-thick phosphor layer beneath a 100- m-thick TBC. The 532-nm (green) excitation light was provided by a frequency-doubled YAG:Nd (yttrium-aluminum-garnet:neodymium) laser, and the fluorescence decay time measurements were acquired with a modified Raman microscope. The preceding graph compares the intensity of the phosphor emission of the phosphor layer above the TBC versus that of the phosphor layer beneath the TBC. Although there was considerable attenuation of the phosphor signal (a factor of 30), the phosphor emission at the reduced intensity was more than sufficient to perform fluorescence decay time measurements. The following graph shows the fluorescence lifetime temperature dependency for the Y2O3:Eu phosphor layers both above and below the TBC. These curves show an excellent match and indicate that, despite the attenuation due to the overlying TBC, the phosphor layer beneath the TBC still functions as an effective temperature indicator.

Photoluminescence in Sm3+ doped Ba2P2O7 phosphor prepared by solution combustion method

NASA Astrophysics Data System (ADS)

Ghawade, Sonal P.; Deshmukh, Kavita A.; Dhoble, S. J.; Deshmukh, Abhay D.

2018-05-01

In this paper, Sm3+ doped Ba2P2O7 phosphors were synthesized via a Solution combustion method. The crystal structure of the phosphor was characterized by XRD. Orange-red emission was observed from these phosphors under near-ultraviolet (UV) excitation at 404 nm. The luminescence properties of the obtained phosphors were characterized by different techniques. The Ba2P2O7:Sm3+ phosphor can be efficiently excited by near-UV and blue light, and their emission spectrum consists of three emission peaks, at 564, 602, and 646 nm, respectively. Based on the results, the as prepared Ba2P2O7:Sm3+ phosphors are promising orange-red-emitting phosphors exhibit great potential may be applicable as a spectral convertor in c-Si solar cell to enhance the efficiency of solar cell in future.

A relative-intensity two-color phosphor thermography system

NASA Technical Reports Server (NTRS)

Merski, N. Ronald

1991-01-01

The NASA LaRC has developed a relative-intensity two-color phosphor thermography system. This system has become a standard technique for acquiring aerothermodynamic data in LaRC Hypersonic Facilities Complex (HFC). The relative intensity theory and its application to the LaRC phosphor thermography system is discussed along with the investment casting technique which is critical to the utilization of the phosphor method for aerothermodynamic studies. Various approaches to obtaining quantitative heat transfer data using thermographic phosphors are addressed and comparisons between thin-film data and thermographic phosphor data on an orbiter-like configuration are presented. In general, data from these two techniques are in good agreement. A discussion is given on the application of phosphors to integration heat transfer data reduction techniques (the thin film method) and preliminary heat transfer data obtained on a calibration sphere using thin-film equations are presented. Finally, plans for a new phosphor system which uses target recognition software are discussed.

Calculation of Manure Production and Excretion of Nitrogen, Phosphorous and Potassium by Dairy Cattle in the Comarca Lagunera

USDA-ARS?s Scientific Manuscript database

The objective of this study is to show how to calculate dairy manure production and the manure content of N, P and K. At the regional level, 7.5 x 106 ton yr-1 of fresh manure is produced, with 12.3% of dry matter (DM) content, for a total of 925,000 ton yr-1 (DM). Total N excreted is 46,200 ton yr-...

Photoluminescence Characteristics of Yag:Ce, Gd Based Phosphors with Different Prehistories

NASA Astrophysics Data System (ADS)

Lisitsyn, V. M.; Soshchin, N. P.; Yang yang, Yu; Stepanov, S. A.; Lisitsyna, L. A.; Tulegenova, A. T.; Abdullin, Kh. A.

2017-09-01

Luminescence characteristics of yttrium-aluminum garnet based phosphor samples differed by their elemental composition and prehistory of synthesis are studied. The morphology, structure, and elemental composition of phosphor samples, their excitation and emission spectra, efficiency of phosphor conversion of chip emission, and kinetics of luminescence decay are measured. The emission characteristics of phosphors are compared with their structural properties and elemental composition.

Examining diapirs as a nutrient source for plants in a High Arctic polar desert.

NASA Astrophysics Data System (ADS)

Hardy, Sarah; Siciliano, Steven

2014-05-01

Polar deserts cover a quarter of ice-free land in the Canadian Arctic, yet little is known about the key ecological processes that take place. This understudied ecosystem is becoming increasingly vulnerable to climate change and growth of the natural resource industry. In polar deserts, below ground soil masses called diapirs occur in some patterned ground features such as frost boils. Diapirs are formed above permafrost soil where increases in moisture and temperature stimulate biological activity when thawing occurs to create an organic rich, Bhy horizon. Vascular plants are scarce (< 5% cover) and nutrients for survival are likely supplied by diapirs but this interaction is poorly understood. To determine if diapirs are an important nutrient source, nitrogen and phosphorous were traced from the diapir Bhy to vascular plants using δ15N and δ18O stable isotope signatures. Recent developments have shown that the oxygen isotopes of orthophosphate (18OP) can be used to trace plant-available phosphorous. At a polar desert site at Alexandra Fjord, Canada, diapir (n=12) and non-diapir (n=12) frost boils were identified in 12 blocks with a field-portable vis-NIR (visible and near infrared spectrometer) device. Soil cores and Salix arctica plant tissue were collected from each frost boil for stable isotope analysis. The δ15N of Salix arctica plant tissue (n=144) shows a significant relationship between block location and diapir presence (p=0.003). There was a consistent pattern in average δ15N in plant tissue parts with increasing concentration from leaf, stem to root in all frost boils. There was no significant difference in total plant δ15N between diapir and non-diapir frost boils but δ15N in soil cores will be measured to determine if these signatures are attributed to the Bhy horizon or biological nitrogen fixation. These results highlight the potential for stable isotopes to be used as a nutrient tracer in polar desert ecosystems and further analysis of phosphorous stable isotopes will provide a clearer picture of the role of diapirs as a nutrient source.

Co-operative energy transfer in Yb3+-Er3+ co-doped SrGdxOy upconverting phosphor

NASA Astrophysics Data System (ADS)

Kumar, Ashwini; Pathak, Trilok K.; Dhoble, S. J.; . Terblans, J. J.; Swart, H. C.

2018-04-01

Upconversion nanoparticles (UCNPs) have shown considerable interest in many fields; however, low upconversion efficiency of UCNPs is still the most severe limitation of their applications. Yb3+ and Er3+ co-doped SrGd4O7/Gd2O3(SGO) upconversion (UC) phosphors were synthesized by a modified co-precipitation process. The UC properties were investigated by direct excitation with a 980 nm laser. It was observed that the as prepared materials showed relatively strong green emission, while upon the incorporation of the Er3+ ion, there was an increase in the upconversion luminescence intensity for the red component. The effect of different doping concentration of Er3+on the emission spectra and X-ray diffraction patterns of the UC materials have also been studied. The luminescence lifetimes and Commission Internationale de L'Eclairage coordinates for these as prepared samples were determined to understand the energy transfer (ET) mechanisms occurring between Yb3+ and Er3+ in the SGO host matrix. The UC luminescence intensity as a function of laser pump power was monitored and it was confirmed that the UC process in SGO:Yb3+/Er3+is a two-photon absorption process. The findings reported here are expected to provide a better approach for understanding of the ET mechanisms in the oxide based Yb3+/Er3+ co-doped UC phosphors. This study might be helpful in precisely defined applications where optical transitions are essential criterion and this can be easily achieved by smart tuning of the emission properties of Yb3+/Er3+ co-doped UC phosphors.

White-emission in single-phase Ba2Gd2Si4O13:Ce3 +,Eu2 +,Sm3 + phosphor for white-LEDs

NASA Astrophysics Data System (ADS)

Jiang, Xiumin; Zhang, Yuqian; Zhang, Jia

2018-03-01

To develop new white-light-emitting phosphor, a series of Ce3 +-Eu2 +-Sm3 + doped Ba2Gd2Si4O13 (BGS) phosphors were prepared by the solid-state reaction method, and their photoluminescence properties were studied. The Ce3 + and Eu2 + single-doped BGS show broad emission bands around in the region of 350-550 and 420-650 nm, respectively. By co-doping Ce3 +-Eu2 + into BGS, the energy transfer (ET) from Ce3 + to Eu2 + is inefficient, which could be due to the competitive absorption between the two activator ions. The Sm3 +-activated BGS exhibits an orangey-red emission in the region of 550-750 nm. To achieve white emission, the BGS:0.06Ce3 +,0.04Eu2 +,ySm3 + (0 ≤ y ≤ 0.18) phosphors were designed, in which the ET from Ce3 +/Eu2 + to Sm3 + was observed. The emission color can be tuned by controlling the Sm3 + concentration, and white emission was obtained in the BGS:0.06Ce3 +,0.04Eu2 +,0.06Sm3 + sample. The investigation of thermal luminescence stability for the typical BGS:0.06Ce3 +,0.04Eu2 +,0.06Sm3 + sample reveals that the emission intensities of both Eu2 + and Sm3 + demonstrate continuous decrease but the Ce3 + emission is enhanced gradually with increasing temperature. The corresponding reason has been discussed.

Optical heat flux gauge

DOEpatents

Noel, Bruce W.; Borella, Henry M.; Cates, Michael R.; Turley, W. Dale; MacArthur, Charles D.; Cala, Gregory C.

1991-01-01

A heat flux gauge comprising first and second thermographic phosphor layers separated by a layer of a thermal insulator wherein each thermographic layer comprises a plurality of respective thermographic phosphors. The gauge may be mounted on a surface with the first thermographic phosphor in contact with the surface. A light source is directed at the gauge, causing the phosphors to luminesce. The luminescence produced by the phosphors is collected and its spectra analyzed in order to determine the heat flux on the surface. First and second phosphor layers must be different materials to assure that the spectral lines collected will be distinguishable.

Fundamental study of phosphor separation by controlling magnetic force

NASA Astrophysics Data System (ADS)

Wada, Kohei; Mishima, Fumihito; Akiyama, Yoko; Nishijima, Shigehiro

2013-11-01

The phosphor wastes consist of phosphors with different emission colors, green (LAP), red (YOX), blue (BAM) and white (HP). It is required to recover and reuse the rare earth phosphors with high market value. In this study, we tried to separate the phosphor using the magnetic separation by HTS bulk magnet utilizing the differences of magnetic susceptibility by the type of phosphors. We succeeded in the successive separation of HP with low market value from YOX and BAM including the rare earth using the magnetic Archimedes method. In this method, vertical and radial components of the magnetic force were used.

Trace, Minor Elements, and Stable Isotopes in Montastraea faveolata as an Indicator of Stress

NASA Astrophysics Data System (ADS)

Holmes, C. W.; Buster, N. A.; Hudson, J. H.

2004-12-01

Coral cores were obtained along the fore reef from Looe Key Reef, Florida Keys, and analyzed for minor and trace elements by laser ablation ICP-MS and stable oxygen and carbon isotopes. Sample locations within the corals were chosen based on the location of annual bands as determined by x-radiographs. The LA-ICP-MS data were obtained along the corallite wall. Boron, magnesium, and phosphorous concentrations can be correlated among the corals analyzed. The highest elemental concentrations and the carbon and oxygen isotopic records in the Looe Key Montastraea faveolata were linked to times of reported bleaching. Boron, a common element in sea water, exists as two species, B(OH)3 below a pH of 8.0 and B(OH)4- above a pH of 8. Hemming and others (1998) determined that boron varied positively with 13C, both being coincident with high-density bands. They proposed that photosynthetic activity of zooxanthellae is the driving process, causing the shift in pH. During periods of stress, energy that would be used for normal coral activity (reproduction and growth) is diverted for tissue repair, food gathering, and waste removal. At extreme stress, these activities are reduced. As a result of decreased zooxanthellate activity, the chemistry at the organic-inorganic boundary may change as follows. 1. The pH rises, increasing the boron levels in the carbonate skeleton. 2. Phosphorous, expelled during normal growth activity, is retained, inhibiting the precipitation of "normal" aragonite. 3. The Mg/Ca ratio changes as calcium is being used preferentially. In the Looe Key Reef corals, boron, magnesium, and phosphorous all were elevated during times of reported bleaching. Within the same time intervals, the δ 13C, which displayed values of between -2 % and -3 % in the "normal" light-density portion of the skeleton, approached a δ 13C of 0 % in the stressed, high-density portion of the skeleton. Thus, the combination of high magnesium, boron, and phosphorous concentrations, coupled with the stable isotopic records of carbon and oxygen, correlate to stress events, such as bleaching in the Looe Key corals. These relations seem to confirm the model proposed by Hemming and others, and this chemistry may be useful in determining the record of stress events in other corals. Hemming, N.G., Guilderson, T.P. and Fairbanks, R.G., 1998, Seasonal variations in the boron isotopic composition of corals, a productivity signal?, Global Biogeochemical Cycles, v. 12, p.581-586.

Synthesis and effect of Sr substitution on fluorescence of new Ba 2-xSr xZnS 3: Eu 2+ red phosphor: Considerable enhancement of emission intensity

NASA Astrophysics Data System (ADS)

Lee, Chi-Woo; Petrykin, Valery; Kakihana, Masato

2009-01-01

A series of 0.5 mol% Eu 2+-activated Ba 2-xSr xZnS 3 phosphor materials were synthesized using precursors prepared by the polymerizable complex method and their fluorescent properties were studied for the first time. It was found that Sr substitution for Ba leads to the considerable improvement of internal quantum efficiency and emission intensity in these materials compared to Ba 2ZnS 3, while emission peak wavelength exhibits a blue shift from 680 to 660 nm. Rietveld refinement of crystal structure of sample with x=0.7 suggests that Sr ions preferentially occupy one of two Ba sites in this compound. Such a structural re-arrangement might be responsible for the observed quantum efficiency dependence on Sr concentration.

Preparation and thermoluminescent dosimetry features of high sensitivity LiF:Mg,Ce phosphor

NASA Astrophysics Data System (ADS)

Shoushtari, M. K.; Zahedifar, M.; Sadeghi, E.

2018-04-01

Thermoluminescence (TL) kinetics and dosimetry features of newly produced LiF doped with Mg and Ce were investigated. Different contents of Mg (0-1 mol%) and Ce (0-2 mol%) were introduced in host material by melting method. The most TL sensitivity of the fabricated phosphor was obtained at 0.7 and 0.05 mol% concentrations of Mg and Ce impurities, respectively. The optimum pre-irradiation annealing regime of the synthesized LiF-based material was found at 350 °C for 10 min. Kinetic parameters of LiF:Mg,Ce dosimeter were obtained using different methods of computerized glow curve deconvolution (CGCD), initial rise (IR) and isothermal decay (ID). A good conformity are observed between the results obtained from different kinetic analysis methods. Other TL features such as fading, dose response and reusability were also examined.

Deciphering the role and nature of phosphate species at the surface of stainless steel immersed in phosphoric acid solutions

NASA Astrophysics Data System (ADS)

Liascukiene, I.; Ben Salah, M.; Sabot, R.; Refait, Ph.; Dhouibi, L.; Méthivier, C.; Landoulsi, J.; Jeannin, M.

2018-03-01

We investigate the evolution of the surface of a highly alloyed stainless steel (Sanicro 28) upon immersion in aqueous phosphoric acid solutions. For this purpose, both short- (few hours) and long-term immersion (several days) were carried out. A detailed analysis of XPS spectra allowed a distinction to be made between oxygen originating from the organic adlayer (adventitious contamination), the passive oxide layer, and adsorbed phosphate species. By estimating the fraction of oxygen due to phosphate species (Oph), it was shown that the Oph/P molar concentration ratio was ranging from about 2 to 3. This suggests the presence of a polyphosphate layer at the stainless steel surface, as also supported by Raman analysis, which influence the electrochemical behavior of SS in the acidic media.

Comparison of the up-conversion photoluminescence for GAP, GAG and GAM phosphors

NASA Astrophysics Data System (ADS)

Deng, Taoli; Jiang, Xianbang

2018-04-01

GdAlO3:Er3+/Yb3+, Gd3Al5O12:Er3+/Yb3+ and Gd4Al2O9:Er3+/Yb3+ phosphors were prepared by co-precipitation. The effects for Gd2O3-Al2O3 composite oxides as the host materials with different crystal structures such as GdAlO3, Gd3Al5O12 and Gd4Al2O9 were investigated. It was found that the perovskite structured GdAlO3:Er3+/Yb3+ (GAP phosphor) could be obtained from the precursor when the calcination temperature was 1000 °C, while the garnet structured Gd3Al5O12:Er3+/Yb3+ (GAG phosphor) could be formed when the calcination temperature was 1300 °C, but the monoclinic-structured Gd4Al2O9:Er3+/Yb3+ (GAM phosphor) could be formed only when the calcination temperature was raised up to 1500 °C. The difference of the up-conversion photoluminescence (UCPL) spectra under 980 nm between the GAP, GAG and GAM phosphors was studied. The result showed that the UCPL intensity of the GAP phosphor was close to that of the GAM phosphor with much higher red-to-green intensity ratio than that of GAP phosphor. The UCPL intensity of GAG phosphor was the weakest among them. Finally, the factors which influenced on the UCPL of the GAP, GAG and GAM phosphors were discussed.

Management of food industry waste employing vermicomposting technology.

PubMed

Garg, V K; Suthar, S; Yadav, Anoop

2012-12-01

This paper reports the vermicomposting of food industry sludges (FIS) mixed with different organic wastes employing Eisenia fetida. A total of 10 vermicomposting units containing different wastes combinations were established. After 15 weeks significant increase in total nitrogen (N(total)) (60-214%), total available phosphorous (P(avail)) (35.8-69.6%), total sodium (Na(total)) (39-95%), and total potassium (K(total)) (43.7-74.1%), while decrease in pH (8.45-19.7%), total organic carbon (OC(total)) (28.4-36.1%) and C:N ratio (61.2-77.8%) was recorded. The results indicated that FIS may be converted into good quality manure by vermicomposting if spiked with other organic wastes in appropriate quantities. Copyright © 2011 Elsevier Ltd. All rights reserved.

X-Ray Microanalysis of Human Cementum

NASA Astrophysics Data System (ADS)

Alvarez-Pérez, Marco Antonio; Alvarez-Fregoso, Octavio; Ortiz-López, Jaime; Arzate, Higinio

2005-08-01

An energy dispersive x-ray microanalysis study was performed throughout the total length of cementum on five impacted human teeth. Mineral content of calcium, phosphorous, and magnesium were determined with an electron probe from the cemento-enamel junction to the root apex on the external surface of the cementum. The concentration profiles for calcium, phosphorous, and magnesium were compared by using Ca/P and Mg/Ca atomic percent ratio. Our findings demonstrated that the Ca/P ratio at the cemento-enamel junction showed the highest values (1.8 2.2). However, the area corresponding to the acellular extrinsic fiber cementum (AEFC) usually located on the coronal one-third of the root surface showed a Ca/P media value of 1.65. Nevertheless, on the area representing the fulcrum of the root there is an abrupt change in the Ca/P ratio, which decreases to 1.3. Our results revealed that Mg2+ distribution throughout the length of human cementum reached its maximum Mg/Ca ratio value of 1.3 1.4 at.% around the fulcrum of the root and an average value of 0.03%. A remarkable finding was that the Mg/Ca ratio pattern distribution showed that in the region where the Ca/P ratio showed a decreasing tendency, the Mg/Ca ratio reached its maximum value, showing a negative correlation. In conclusion, this study has established that clear compositional differences exist between AEFC and cellular mixed stratified cementum varieties and adds new knowledge about Mg2+ distribution and suggests its provocative role regulating human cementum metabolism.

Improving Water Use Efficiency of Lettuce (Lactuca sativa L.) Using Phosphorous Fertilizers.

PubMed

Alkhader, Asad M F; Abu Rayyan, Azmi M

2013-01-01

A greenhouse pot experiment was conducted to evaluate the effect of phosphorous (P) fertilizers application to an alkaline calcareous soil on the water use efficiency (WUE) of lettuce cultivar "robinson" of iceberg type. Head fresh and dry weights, total water applied and WUE were affected significantly by the P fertilizer type and rate. P fertilizers addition induced a significant enhancement in the WUE and fresh and dry weights of the crop. A local phosphate rock (PR) applied directly was found to be inferior to the other types of P fertilizers (Mono ammonium phosphate (MAP), Single superphosphate (SSP), and Di ammonium phosphate ((DAP)). MAP fertilizer at 375 and 500 kg P2O5/ha application rates recorded the highest significant values of head fresh weight and WUE, respectively.

Energy transfer and tunable multicolor emission and paramagnetic properties of GdF3:Dy(3+),Tb(3+),Eu(3+) phosphors.

PubMed

Guan, Hongxia; Sheng, Ye; Xu, Chengyi; Dai, Yunzhi; Xie, Xiaoming; Zou, Haifeng

2016-07-20

A series of Dy(3+), Tb(3+), Eu(3+) singly or doubly or triply doped GdF3 phosphors were synthesized by a glutamic acid assisted one-step hydrothermal method. The samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and photoluminescence (PL) spectroscopy. The results show that the synthesized samples are all pure GdF3. The obtained samples have a peanut-like morphology with a diameter of about 270 nm and a length of about 600 nm. Under UV excitation, GdF3:Dy(3+), GdF3:Tb(3+) and GdF3:Eu(3+) samples exhibit strong blue, green and red emissions, respectively. By adjusting their relative doping concentrations in the GdF3 host, the different color hues of green and red light are obtained by co-doped Dy(3+), Tb(3+) and Tb(3+), Eu(3+) ions in the GdF3 host, respectively. Besides, there exist two energy transfer pairs in the GdF3 host: (1) Dy(3+) → Tb(3+) and (2) Tb(3+) → Eu(3+). More significantly, in the Dy(3+), Tb(3+), and Eu(3+) tri-doped GdF3 phosphors, white light can also be achieved upon excitation of UV light by adjusting the doping concentration of Eu(3+). In addition, the obtained samples also exhibit paramagnetic properties at room temperature (300 K) and low temperature (2 K). It is obvious that multifunctional Dy(3+), Tb(3+), Eu(3+) tri-doped GdF3 materials including tunable multicolors and intrinsic paramagnetic properties may have potential applications in the field of full-color displays.

40 CFR 63.600 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Hazardous Air Pollutants From Phosphoric Acid Manufacturing Plants § 63.600 Applicability. (a... apply to the owner or operator of each phosphoric acid manufacturing plant. (b) The requirements of this... affected sources at a phosphoric acid manufacturing plant: (1) Each wet-process phosphoric acid process...

40 CFR 63.600 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants From Phosphoric Acid Manufacturing Plants § 63.600 Applicability. (a... apply to the owner or operator of each phosphoric acid manufacturing plant. (b) The requirements of this... affected sources at a phosphoric acid manufacturing plant: (1) Each wet-process phosphoric acid process...

Enhancing Photovoltaic Performance Using Broadband Luminescent Down-Shifting by Combining Multiple Species of Eu-Doped Silicate Phosphors.

PubMed

Ho, Wen-Jeng; Shen, Yu-Tang; Liu, Jheng-Jie; You, Bang-Jin; Ho, Chun-Hung

2017-10-21

This paper demonstrates the application of a broadband luminescent downshifting (LDS) layer with multiple species of europium (Eu)-doped silicate phosphors using spin-on film technique to enhance the photovoltaic efficiency of crystalline silicon solar cells. The surface morphology of the deposited layer was examined using a scanning electron microscope (SEM). The chemical composition of the Eu-doped silicate phosphors was analyzed using energy-dispersive X-ray spectroscopy (EDS). The fluorescence emission of the Eu-doped silicate phosphors was characterized using photoluminescence (PL) measurements at room temperature. We also compared the optical reflectance and external quantum efficiency (EQE) response of cells with combinations of various Eu-doped phosphors species. The cell coated with two species of Eu-doped phosphors achieved a conversion efficiency enhancement (∆ η ) of 19.39%, far exceeding the ∆ η = 15.08% of the cell with one species of Eu-doped phosphors and the ∆ η = 8.51% of the reference cell with the same silicate layer without Eu-doped phosphors.

Modeling on the cathodoluminescence properties of the thin film phosphors for field emission flat panel displays

NASA Astrophysics Data System (ADS)

Cho, Kyu-Gong

2000-12-01

In order to investigate the effects of the film roughness with the fundamental luminance parameters of thin film phosphors, Y2 O3:Eu films with different thickness and roughness values were deposited on various substrate materials using a pulsed laser deposition technique under a controlled experimental procedure. The best luminous efficiency was observed from the Y2O3:Eu films on quartz substrates due to the smaller refractive index and low absorption characteristics of the quartz substrates which produce a larger amount of total internal reflection in the film and low loss of light intensity during the multiple internal reflections. The trapped light inside the film can escape the film more easily due to rougher film surface. The better epitaxial growth capability of the Y2O 3:Eu films with the LaAlO3 substrates resulted in higher luminous efficiency in the small surface roughness region. Higher luminous efficiency was observed in reflection mode than in transmission mode due to the contribution of diffusely scattered light at the air-film interface. A new theoretical model based on the diffraction scattering theory of light, the steady-state diffusion condition of carriers and the Kanaya-Okayama's electron- beam-solid interaction range satisfactorily explains all the experimental results mentioned above. The model also provides solid understandings on the cathodoluminescence properties of the thin film phosphors with the effects of other single or multiple luminance parameters. The parameters encountered for the model are surface roughness, electron-beam-solid interaction, surface recombination rate of carriers, charge carrier diffusion properties, multiple scattering at the interfaces (air- film, film-substrate, and substrate-air), optical properties of the material, film thickness, and substrate type. The model supplies a general solution in both qualitative and quantitative ways to estimate the luminance properties of the thin film phosphors and it can be utilized to optimize the thin film phosphor properties for the application of field emission flat panel displays.

Complex study on photoluminescence properties of YAG:Ce,Gd phosphors

NASA Astrophysics Data System (ADS)

Lisitsyn, V. M.; Ju, Yangyang; Stepanov, S. A.; Soschin, N. M.

2017-05-01

Luminescence characteristics of gadolinium co-doped yttrium aluminium garnet doped with cerium phosphors were studied. In this work, powder X-ray diffraction (XRD) spectra, elemental composition analyses, excitation and emission spectra, conversion efficiency of emission phosphor, corresponding (CIE) chromaticity colour coordinates and pulsed photoluminescence decay kinetic curves were investigated, all the measurements were performed at room temperature. The properties of the phosphors were studied by comparing the composition of the phosphors and their luminescent properties.

The improvement of moisture resistance and thermal stability of Ca 3SiO 4Cl 2:Eu 2+ phosphor coated with SiO 2

NASA Astrophysics Data System (ADS)

Zhuang, Jiaqing; Xia, Zhiguo; Liu, Haikun; Zhang, Zepeng; Liao, Libing

2011-02-01

Green-emitting phosphors Ca3SiO4Cl2:Eu2+ were prepared by the high temperature solid-state method. Sol-gel process was adopted to encapsulate the as-prepared phosphors with tetraethylorthosilicate (TEOS) as silicon coating reagent. Fluorescence spectrometer, scanning electron microscopy (SEM) and powder X-ray diffraction (XRD) patterns were employed to characterize the emission spectra, the surface morphologies and the phase structures, respectively. The chemical stability testing was operated by the method of soaking the phosphors in deionized water and roasting them at different temperatures. The results indicated that the surfaces of the green phosphors were evenly coated by SiO2 and the phase structure of the coated phosphors remained the same as the uncoated samples. The luminance centre of Eu2+ did not shift after surface treatment and the luminance intensity of coated phosphors was lower than that of the uncoated samples. The results demonstrated that the water-resistance stability of the coated phosphor was improved to some degree because the pH value and the luminance intensity variation were both smaller than the uncoated phosphor after steeping within the same time. Moreover, the thermal stability of coated phosphors was enhanced obviously compared to the original samples based on the temperature dependent emission spectra measurement.

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida

PubMed Central

Wani, K.A.; Mamta; Rao, R.J.

2013-01-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste. PMID:23961230

Long-persistence blue phosphors

NASA Technical Reports Server (NTRS)

Yen, William M. (Inventor); Jia, Weiyi (Inventor); Lu, Lizhu (Inventor); Yuan, Huabiao (Inventor)

2000-01-01

This invention relates to phosphors including long-persistence blue phosphors. Phosphors of the invention are represented by the general formula: MO . mAl.sub.2 O.sub.3 :Eu.sup.2+,R.sup.3+ wherein m is a number ranging from about 1.6 to about 2.2, M is Sr or a combination of Sr with Ca and Ba or both, R.sup.3+ is a trivalent metal ion or trivalent Bi or a mixture of these trivalent ions, Eu.sup.2+ is present at a level up to about 5 mol % of M, and R.sup.3+ is present at a level up to about 5 mol % of M. Phosphors of this invention include powders, ceramics, single crystals and single crystal fibers. A method of manufacturing improved phosphors and a method of manufacturing single crystal phosphors are also provided.

Phosphors for LED lamps

DOEpatents

Murphy, James Edward; Manepalli, Satya Kishore; Kumar, Prasanth Nammalwar

2013-08-13

A phosphor, a phosphor blend including the phosphor, a phosphor prepared by a process, and a lighting apparatus including the phosphor blend are disclosed. The phosphor has the formula (Ca.sub.1-p-qCe.sub.pK.sub.q).sub.xSc.sub.y(Si.sub.1-rGa.sub.r).sub.zO.su- b.12+.delta. or derived from a process followed using disclosed amounts of reactants. In the formula, (0

Bacterial and Archaeal Communities Variability Associated with Upwelling and Anthropogenic Pressures in the Protection Area of Arraial do Cabo (Cabo Frio region - RJ).

PubMed

Coelho-Souza, Sergio A; Araújo, Fábio V; Cury, Juliano C; Jesus, Hugo E; Pereira, Gilberto C; Guimarães, Jean R D; Peixoto, Raquel S; Dávila, Alberto M R; Rosado, Alexandre S

2015-09-01

Upwelling systems contain a high diversity of pelagic microorganisms and their composition and activity are defined by factors like temperature and nutrient concentration. Denaturing gradient gel electrophoresis (DGGE) technique was used to verify the spatial and temporal genetic variability of Bacteria and Archaea in two stations of the Arraial do Cabo coastal region, one under upwelling pressure and another under anthropogenic pressure. In addition, biotic and abiotic variables were measured in surface and deep waters from three other stations between these stations. Six samplings were done during a year and adequately represented the degrees of upwelling and anthropogenic pressures to the system. Principal Component Analysis (PCA) showed negative correlations between the concentrations of ammonia and phosphorous with prokaryotic secondary production and the total heterotrophic bacteria. PCA also showed negative correlation between temperature and the abundance of prokaryotic cells. Bacterial and archaeal compositions were changeable as were the oceanographic conditions, and upwelling had a regional pressure while anthropogenic pressure was punctual. We suggest that the measurement of prokaryotic secondary production was associated with both Bacteria and Archaea activities, and that substrate availability and temperature determine nutrients cycling.

Impact of Distillery Spent Wash Irrigation on Agricultural Soil

NASA Astrophysics Data System (ADS)

Jadhav, Ramanand N.; Sarode, Dhananjay B.; Narkhede, Sachin D.; Khatik, Vasimshaikh A.; Attarde, Sanjay B.

2011-07-01

The disposal of wastes from industrial sources is becoming a serious problem throughout the world. In India, a total of approximately 40 million m3 of distillery spent wash is generated annually from 295 distilleries. The distillery spent wash is acidic and high levels of biological oxygen demand and chemical oxygen demand and contains nutrient elements such as potassium (K), nitrogen (N), and phosphorous (P). It is used as a source of plant nutrients and organic matter for various agricultural crops. It is usually applied to arable land near the distilleries as irrigation water or as a soil amendment. However, indiscriminate disposal of it has resulted in adverse impact on soil environments. This paper aims to identify the impact of distillery spent wash application for irrigation and on soil environment. The distillery spent wash can be a good source of nutrients necessary for plant growth. Application of various concentrations of spent wash on plant species was studied. A plot having 20-30% concentration of spent wash observed good growth. At higher doses, spent wash application is found harmful to crop growth and soil fertility and its use at lower doses remarkably improves germination and growth of crops.

Utilization of molasses and sugar cane bagasse for production of fungal invertase in solid state fermentation using Aspergillus niger GH1

PubMed Central

Veana, F.; Martínez-Hernández, J.L.; Aguilar, C.N.; Rodríguez-Herrera, R.; Michelena, G.

2014-01-01

Agro-industrial wastes have been used as substrate-support in solid state fermentation for enzyme production. Molasses and sugarcane bagasse are by-products of sugar industry and can be employed as substrates for invertase production. Invertase is an important enzyme for sweeteners development. In this study, a xerophilic fungus Aspergillus niger GH1 isolated of the Mexican semi-desert, previously reported as an invertase over-producer strain was used. Molasses from Mexico and Cuba were chemically analyzed (total and reducer sugars, nitrogen and phosphorous contents); the last one was selected based on chemical composition. Fermentations were performed using virgin and hydrolyzate bagasse (treatment with concentrated sulfuric acid). Results indicated that, the enzymatic yield (5231 U/L) is higher than those reported by other A. niger strains under solid state fermentation, using hydrolyzate bagasse. The acid hydrolysis promotes availability of fermentable sugars. In addition, maximum invertase activity was detected at 24 h using low substrate concentration, which may reduce production costs. This study presents an alternative method for invertase production using a xerophilic fungus isolated from Mexican semi-desert and inexpensive substrates (molasses and sugarcane bagasse). PMID:25242918

40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

21 CFR 175.260 - Partial phosphoric acid esters of polyester resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Partial phosphoric acid esters of polyester resins... of polyester resins. Partial phosphoric acid esters of polyester resins identified in this section... prescribed conditions: (a) For the purpose of this section, partial phosphoric acid esters of polyester...

40 CFR 721.10220 - Phosphoric acid, polymer with cycloaliphatic diglycidyl ether, alkylethers (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Phosphoric acid, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10220 Phosphoric acid, polymer with... to reporting. (1) The chemical substance identified generically as phosphoric acid, polymer with...

40 CFR 721.10685 - Phosphoric acid, mixed esters (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphoric acid, mixed esters (generic... Specific Chemical Substances § 721.10685 Phosphoric acid, mixed esters (generic). (a) Chemical substance... phosphoric acid, mixed esters (PMN P-13-170) is subject to reporting under this section for the significant...

40 CFR 721.6110 - Alkyldi(alkyloxyhydroxypropyl) derivative, phosphoric acid esters, potassium salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) derivative, phosphoric acid esters, potassium salts. 721.6110 Section 721.6110 Protection of Environment...) derivative, phosphoric acid esters, potassium salts. (a) Chemical substance and significant new uses subject...) derivative, phosphoric acid esters, potassium salts (PMN P-91-818) is subject to reporting under this section...

40 CFR 721.6110 - Alkyldi(alkyloxyhydroxypropyl) derivative, phosphoric acid esters, potassium salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) derivative, phosphoric acid esters, potassium salts. 721.6110 Section 721.6110 Protection of Environment...) derivative, phosphoric acid esters, potassium salts. (a) Chemical substance and significant new uses subject...) derivative, phosphoric acid esters, potassium salts (PMN P-91-818) is subject to reporting under this section...

40 CFR 721.6110 - Alkyldi(alkyloxyhydroxypropyl) derivative, phosphoric acid esters, potassium salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) derivative, phosphoric acid esters, potassium salts. 721.6110 Section 721.6110 Protection of Environment...) derivative, phosphoric acid esters, potassium salts. (a) Chemical substance and significant new uses subject...) derivative, phosphoric acid esters, potassium salts (PMN P-91-818) is subject to reporting under this section...

40 CFR 721.6110 - Alkyldi(alkyloxyhydroxypropyl) derivative, phosphoric acid esters, potassium salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) derivative, phosphoric acid esters, potassium salts. 721.6110 Section 721.6110 Protection of Environment...) derivative, phosphoric acid esters, potassium salts. (a) Chemical substance and significant new uses subject...) derivative, phosphoric acid esters, potassium salts (PMN P-91-818) is subject to reporting under this section...

40 CFR 721.10220 - Phosphoric acid, polymer with cycloaliphatic diglycidyl ether, alkylethers (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Phosphoric acid, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10220 Phosphoric acid, polymer with... to reporting. (1) The chemical substance identified generically as phosphoric acid, polymer with...

40 CFR 721.10220 - Phosphoric acid, polymer with cycloaliphatic diglycidyl ether, alkylethers (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Phosphoric acid, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10220 Phosphoric acid, polymer with... to reporting. (1) The chemical substance identified generically as phosphoric acid, polymer with...

40 CFR 721.10220 - Phosphoric acid, polymer with cycloaliphatic diglycidyl ether, alkylethers (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphoric acid, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10220 Phosphoric acid, polymer with... to reporting. (1) The chemical substance identified generically as phosphoric acid, polymer with...

Evaluation of Microencapsulated Phosphors.

DTIC Science & Technology

1979-05-01

microencapsulated phosphors of the same control lot with nominal 0.5, 1.0, and 3.0-micron walls. Light output was normalized with respect to the amount of phosphor...had indicated that microencapsulation enhanced the light output of phosphors. The original results were not confirmed although the same procedures and material lots were used. (Author)

40 CFR 721.6097 - Phosphoric acid derivative (generic name).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphoric acid derivative (generic... Specific Chemical Substances § 721.6097 Phosphoric acid derivative (generic name). (a) Chemical substance... phosphoric acid derivative (PMN P-95-284) is subject to reporting under this section for the significant new...

40 CFR 721.6097 - Phosphoric acid derivative (generic name).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Phosphoric acid derivative (generic... Specific Chemical Substances § 721.6097 Phosphoric acid derivative (generic name). (a) Chemical substance... phosphoric acid derivative (PMN P-95-284) is subject to reporting under this section for the significant new...

40 CFR 721.6110 - Alkyldi(alkyloxyhydroxypropyl) derivative, phosphoric acid esters, potassium salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) derivative, phosphoric acid esters, potassium salts. 721.6110 Section 721.6110 Protection of Environment...) derivative, phosphoric acid esters, potassium salts. (a) Chemical substance and significant new uses subject...) derivative, phosphoric acid esters, potassium salts (PMN P-91-818) is subject to reporting under this section...