Method and apparatus for transfer function simulator for testing complex systems

NASA Technical Reports Server (NTRS)

Kavaya, M. J. (Inventor)

1985-01-01

A method and apparatus for testing the operation of a complex stabilization circuit in a closed loop system is presented. The method is comprised of a programmed analog or digital computing system for implementing the transfer function of a load thereby providing a predictable load. The digital computing system employs a table stored in a microprocessor in which precomputed values of the load transfer function are stored for values of input signal from the stabilization circuit over the range of interest. This technique may be used not only for isolating faults in the stabilization circuit, but also for analyzing a fault in a faulty load by so varying parameters of the computing system as to simulate operation of the actual load with the fault.

Active ankle dorsiflexion and the Mingazzini manoeuvre: two clinical bedside tests related to prognosis of postural transferring, standing and walking ability in patients with stroke.

PubMed

Smania, N; Gambarin, M; Paolucci, S; Girardi, P; Bortolami, M; Fiaschi, A; Santilli, V; Picelli, A

2011-09-01

Lower limb paresis is one of the main determinants of postural transferring, standing and walking disability in patients with stroke. Early prognosis of recovery of lower limb function and of related functional disability is an important issue in neurorehabilitation clinical practice. Aim of this study was to assess the relationship between active ankle dorsiflexion and the Mingazzini manoeuvre with the prognosis of lower limb function and of postural transferring, standing and walking ability in patients with stroke. This was a longitudinal study with prospectively collected data. University hospital. The study included 53 patients with first unilateral brain ischemic stroke. Patients were evaluated initially (mean 4.02 days) and approximately at six months (mean 178.6 days) after stroke. Initial assessment included active ankle dorsiflexion and the Mingazzini manoeuvre. The assessment after six months included three outcome measures evaluating the rate of improvement of lower limb function and of postural transferring, standing and walking ability (Postural Assessment Scale for Stroke patients, Functional Ambulation Category, Motricity Index leg subtest). The active ankle dorsiflexion showed to be related with the prognosis of lower limb function and of walking ability, while the Mingazzini manoeuvre was related with the improvement of postural transferring and standing ability. Active ankle dorsiflexion and the Mingazzini manoeuvre are related with the prognosis of lower limb function and of postural transferring, standing and walking ability in patients with stroke. These simple bedside tests give a picture of improvement potential of motor activities connected to lower limb function in patients with acute stroke.

Ground Test of the Urine Processing Assembly for Accelerations and Transfer Functions

NASA Technical Reports Server (NTRS)

Houston, Janice; Almond, Deborah F. (Technical Monitor)

2001-01-01

This viewgraph presentation gives an overview of the ground test of the urine processing assembly for accelerations and transfer functions. Details are given on the test setup, test data, data analysis, analytical results, and microgravity assessment. The conclusions of the tests include the following: (1) the single input/multiple output method is useful if the data is acquired by tri-axial accelerometers and inputs can be considered uncorrelated; (2) tying coherence with the matrix yields higher confidence in results; (3) the WRS#2 rack ORUs need to be isolated; (4) and future work includes a plan for characterizing performance of isolation materials.

The transfer of Crel contextual control (same, opposite, less than, more than) through equivalence relations.

PubMed

Perez, William F; Kovac, Roberta; Nico, Yara C; Caro, Daniel M; Fidalgo, Adriana P; Linares, Ila; de Almeida, João Henrique; de Rose, Júlio C

2017-11-01

According to Relational Frame Theory (RFT) C rel denotes a contextual stimulus that controls a particular type of relational response (sameness, opposition, comparative, temporal, hierarchical etc.) in a given situation. Previous studies suggest that contextual functions may be indirectly acquired via transfer of function. The present study investigated the transfer of C rel contextual control through equivalence relations. Experiment 1 evaluated the transfer of C rel contextual functions for relational responses based on sameness and opposition. Experiment 2 extended these findings by evaluating transfer of function using comparative C rel stimuli. Both experiments followed a similar sequence of phases. First, abstract forms were established as C rel stimuli via multiple exemplar training (Phase 1). The contextual cues were then applied to establish arbitrary relations among nonsense words and to test derived relations (Phase 2). After that, equivalence relations involving the original C rel stimuli and other abstract forms were trained and tested (Phase 3). Transfer of function was evaluated by replacing the directly established C rel stimuli with their equivalent stimuli in the former experimental tasks (Phases 1 and 2). Results from both experiments suggest that C rel contextual control may be extended via equivalence relations, allowing other arbitrarily related stimuli to indirectly acquire C rel functions and regulate behavior by evoking appropriate relational responses in the presence of both previously known and novel stimuli. © 2017 Society for the Experimental Analysis of Behavior.

Automatic transfer function design for medical visualization using visibility distributions and projective color mapping.

PubMed

Cai, Lile; Tay, Wei-Liang; Nguyen, Binh P; Chui, Chee-Kong; Ong, Sim-Heng

2013-01-01

Transfer functions play a key role in volume rendering of medical data, but transfer function manipulation is unintuitive and can be time-consuming; achieving an optimal visualization of patient anatomy or pathology is difficult. To overcome this problem, we present a system for automatic transfer function design based on visibility distribution and projective color mapping. Instead of assigning opacity directly based on voxel intensity and gradient magnitude, the opacity transfer function is automatically derived by matching the observed visibility distribution to a target visibility distribution. An automatic color assignment scheme based on projective mapping is proposed to assign colors that allow for the visual discrimination of different structures, while also reflecting the degree of similarity between them. When our method was tested on several medical volumetric datasets, the key structures within the volume were clearly visualized with minimal user intervention. Copyright © 2013 Elsevier Ltd. All rights reserved.

The partial coherence modulation transfer function in testing lithography lens

NASA Astrophysics Data System (ADS)

Huang, Jiun-Woei

2018-03-01

Due to the lithography demanding high performance in projection of semiconductor mask to wafer, the lens has to be almost free in spherical and coma aberration, thus, in situ optical testing for diagnosis of lens performance has to be established to verify the performance and to provide the suggesting for further improvement of the lens, before the lens has been build and integrated with light source. The measurement of modulation transfer function of critical dimension (CD) is main performance parameter to evaluate the line width of semiconductor platform fabricating ability for the smallest line width of producing tiny integrated circuits. Although the modulation transfer function (MTF) has been popularly used to evaluation the optical system, but in lithography, the contrast of each line-pair is in one dimension or two dimensions, analytically, while the lens stand along in the test bench integrated with the light source coherent or near coherent for the small dimension near the optical diffraction limit, the MTF is not only contributed by the lens, also by illumination of platform. In the study, the partial coherence modulation transfer function (PCMTF) for testing a lithography lens is suggested by measuring MTF in the high spatial frequency of in situ lithography lens, blended with the illumination of partial and in coherent light source. PCMTF can be one of measurement to evaluate the imperfect lens of lithography lens for further improvement in lens performance.

Linear modeling of steady-state behavioral dynamics.

PubMed Central

Palya, William L; Walter, Donald; Kessel, Robert; Lucke, Robert

2002-01-01

The observed steady-state behavioral dynamics supported by unsignaled periods of reinforcement within repeating 2,000-s trials were modeled with a linear transfer function. These experiments employed improved schedule forms and analytical methods to improve the precision of the measured transfer function, compared to previous work. The refinements include both the use of multiple reinforcement periods that improve spectral coverage and averaging of independently determined transfer functions. A linear analysis was then used to predict behavior observed for three different test schedules. The fidelity of these predictions was determined. PMID:11831782

Neurocognitive enhancement in older adults: comparison of three cognitive training tasks to test a hypothesis of training transfer in brain connectivity.

PubMed

Strenziok, Maren; Parasuraman, Raja; Clarke, Ellen; Cisler, Dean S; Thompson, James C; Greenwood, Pamela M

2014-01-15

The ultimate goal of cognitive enhancement as an intervention for age-related cognitive decline is transfer to everyday cognitive functioning. Development of training methods that transfer broadly to untrained cognitive tasks (far transfer) requires understanding of the neural bases of training and far transfer effects. We used cognitive training to test the hypothesis that far transfer is associated with altered attentional control demands mediated by the dorsal attention network and trained sensory cortex. In an exploratory study, we randomly assigned 42 healthy older adults to six weeks of training on Brain Fitness (BF-auditory perception), Space Fortress (SF-visuomotor/working memory), or Rise of Nations (RON-strategic reasoning). Before and after training, cognitive performance, diffusion-derived white matter integrity, and functional connectivity of the superior parietal cortex (SPC) were assessed. We found the strongest effects from BF training, which transferred to everyday problem solving and reasoning and selectively changed integrity of occipito-temporal white matter associated with improvement on untrained everyday problem solving. These results show that cognitive gain from auditory perception training depends on heightened white matter integrity in the ventral attention network. In BF and SF (which also transferred positively), a decrease in functional connectivity between SPC and inferior temporal lobe (ITL) was observed compared to RON-which did not transfer to untrained cognitive function. These findings highlight the importance for cognitive training of top-down control of sensory processing by the dorsal attention network. Altered brain connectivity - observed in the two training tasks that showed far transfer effects - may be a marker for training success. © 2013 Elsevier Inc. All rights reserved.

Testing time-dependent density functional theory with depopulated molecular orbitals for predicting electronic excitation energies of valence, Rydberg, and charge-transfer states and potential energies near a conical intersection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Shaohong L.; Truhlar, Donald G., E-mail: truhlar@umn.edu

2014-09-14

Kohn-Sham (KS) time-dependent density functional theory (TDDFT) with most exchange-correlation functionals is well known to systematically underestimate the excitation energies of Rydberg and charge-transfer excited states of atomic and molecular systems. To improve the description of Rydberg states within the KS TDDFT framework, Gaiduk et al. [Phys. Rev. Lett. 108, 253005 (2012)] proposed a scheme that may be called HOMO depopulation. In this study, we tested this scheme on an extensive dataset of valence and Rydberg excitation energies of various atoms, ions, and molecules. It is also tested on a charge-transfer excitation of NH{sub 3}-F{sub 2} and on the potentialmore » energy curves of NH{sub 3} near a conical intersection. We found that the method can indeed significantly improve the accuracy of predicted Rydberg excitation energies while preserving reasonable accuracy for valence excitation energies. However, it does not appear to improve the description of charge-transfer excitations that are severely underestimated by standard KS TDDFT with conventional exchange-correlation functionals, nor does it perform appreciably better than standard TDDFT for the calculation of potential energy surfaces.« less

Testing the Kerr Black Hole Hypothesis Using X-Ray Reflection Spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bambi, Cosimo; Nampalliwar, Sourabh; Cárdenas-Avendaño, Alejandro

We present the first X-ray reflection model for testing the assumption that the metric of astrophysical black holes is described by the Kerr solution. We employ the formalism of the transfer function proposed by Cunningham. The calculations of the reflection spectrum of a thin accretion disk are split into two parts: the calculation of the transfer function and the calculation of the local spectrum at any emission point in the disk. The transfer function only depends on the background metric and takes into account all the relativistic effects (gravitational redshift, Doppler boosting, and light bending). Our code computes the transfermore » function for a spacetime described by the Johannsen metric and can easily be extended to any stationary, axisymmetric, and asymptotically flat spacetime. Transfer functions and single line shapes in the Kerr metric are compared to those calculated from existing codes to check that we reach the necessary accuracy. We also simulate some observations with NuSTAR and LAD/eXTP and fit the data with our new model to show the potential capabilities of current and future observations to constrain possible deviations from the Kerr metric.« less

Electronic Coupling Calculations for Bridge-Mediated Charge Transfer Using Constrained Density Functional Theory (CDFT) and Effective Hamiltonian Approaches at the Density Functional Theory (DFT) and Fragment-Orbital Density Functional Tight Binding (FODFTB) Level

DOE PAGES

Gillet, Natacha; Berstis, Laura; Wu, Xiaojing; ...

2016-09-09

In this paper, four methods to calculate charge transfer integrals in the context of bridge-mediated electron transfer are tested. These methods are based on density functional theory (DFT). We consider two perturbative Green's function effective Hamiltonian methods (first, at the DFT level of theory, using localized molecular orbitals; second, applying a tight-binding DFT approach, using fragment orbitals) and two constrained DFT implementations with either plane-wave or local basis sets. To assess the performance of the methods for through-bond (TB)-dominated or through-space (TS)-dominated transfer, different sets of molecules are considered. For through-bond electron transfer (ET), several molecules that were originally synthesizedmore » by Paddon-Row and co-workers for the deduction of electronic coupling values from photoemission and electron transmission spectroscopies, are analyzed. The tested methodologies prove to be successful in reproducing experimental data, the exponential distance decay constant and the superbridge effects arising from interference among ET pathways. For through-space ET, dedicated p-stacked systems with heterocyclopentadiene molecules were created and analyzed on the basis of electronic coupling dependence on donor-acceptor distance, structure of the bridge, and ET barrier height. The inexpensive fragment-orbital density functional tight binding (FODFTB) method gives similar results to constrained density functional theory (CDFT) and both reproduce the expected exponential decay of the coupling with donor-acceptor distances and the number of bridging units. Finally, these four approaches appear to give reliable results for both TB and TS ET and present a good alternative to expensive ab initio methodologies for large systems involving long-range charge transfers.« less

Electronic Coupling Calculations for Bridge-Mediated Charge Transfer Using Constrained Density Functional Theory (CDFT) and Effective Hamiltonian Approaches at the Density Functional Theory (DFT) and Fragment-Orbital Density Functional Tight Binding (FODFTB) Level

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gillet, Natacha; Berstis, Laura; Wu, Xiaojing

In this paper, four methods to calculate charge transfer integrals in the context of bridge-mediated electron transfer are tested. These methods are based on density functional theory (DFT). We consider two perturbative Green's function effective Hamiltonian methods (first, at the DFT level of theory, using localized molecular orbitals; second, applying a tight-binding DFT approach, using fragment orbitals) and two constrained DFT implementations with either plane-wave or local basis sets. To assess the performance of the methods for through-bond (TB)-dominated or through-space (TS)-dominated transfer, different sets of molecules are considered. For through-bond electron transfer (ET), several molecules that were originally synthesizedmore » by Paddon-Row and co-workers for the deduction of electronic coupling values from photoemission and electron transmission spectroscopies, are analyzed. The tested methodologies prove to be successful in reproducing experimental data, the exponential distance decay constant and the superbridge effects arising from interference among ET pathways. For through-space ET, dedicated p-stacked systems with heterocyclopentadiene molecules were created and analyzed on the basis of electronic coupling dependence on donor-acceptor distance, structure of the bridge, and ET barrier height. The inexpensive fragment-orbital density functional tight binding (FODFTB) method gives similar results to constrained density functional theory (CDFT) and both reproduce the expected exponential decay of the coupling with donor-acceptor distances and the number of bridging units. Finally, these four approaches appear to give reliable results for both TB and TS ET and present a good alternative to expensive ab initio methodologies for large systems involving long-range charge transfers.« less

Electronic Coupling Calculations for Bridge-Mediated Charge Transfer Using Constrained Density Functional Theory (CDFT) and Effective Hamiltonian Approaches at the Density Functional Theory (DFT) and Fragment-Orbital Density Functional Tight Binding (FODFTB) Level.

PubMed

Gillet, Natacha; Berstis, Laura; Wu, Xiaojing; Gajdos, Fruzsina; Heck, Alexander; de la Lande, Aurélien; Blumberger, Jochen; Elstner, Marcus

2016-10-11

In this article, four methods to calculate charge transfer integrals in the context of bridge-mediated electron transfer are tested. These methods are based on density functional theory (DFT). We consider two perturbative Green's function effective Hamiltonian methods (first, at the DFT level of theory, using localized molecular orbitals; second, applying a tight-binding DFT approach, using fragment orbitals) and two constrained DFT implementations with either plane-wave or local basis sets. To assess the performance of the methods for through-bond (TB)-dominated or through-space (TS)-dominated transfer, different sets of molecules are considered. For through-bond electron transfer (ET), several molecules that were originally synthesized by Paddon-Row and co-workers for the deduction of electronic coupling values from photoemission and electron transmission spectroscopies, are analyzed. The tested methodologies prove to be successful in reproducing experimental data, the exponential distance decay constant and the superbridge effects arising from interference among ET pathways. For through-space ET, dedicated π-stacked systems with heterocyclopentadiene molecules were created and analyzed on the basis of electronic coupling dependence on donor-acceptor distance, structure of the bridge, and ET barrier height. The inexpensive fragment-orbital density functional tight binding (FODFTB) method gives similar results to constrained density functional theory (CDFT) and both reproduce the expected exponential decay of the coupling with donor-acceptor distances and the number of bridging units. These four approaches appear to give reliable results for both TB and TS ET and present a good alternative to expensive ab initio methodologies for large systems involving long-range charge transfers.

Neurophysiological evidence for transfer appropriate processing of memory: processing versus feature similarity.

PubMed

Schendan, Haune E; Kutas, Malra

2007-08-01

Transfer appropriate processing (TAP) accounts propose that memory is a function of the degree to which the same neural processes transfer appropriately from the study experience to the memory test. However, in prior research, study and test stimuli were often similar physically. In two experiments, event-related brain potentials (ERPs) were recorded to fragmented objects during an indirect memory test to isolate transfer of a specific perceptual process from overlap of physical features between experiences. An occipitotemporoparietal P2(00) at 200 msec showed implicit memory effects only when similar perceptual grouping processes of good continuation were repeatedly engaged-despite physical feature differences--as TAP accounts hypothesize. This result provides direct neurophysiological evidence for the critical role of process transfer across experiences for memory.

Comparison of Commercial Electromagnetic Interface Test Techniques to NASA Electromagnetic Interference Test Techniques

NASA Astrophysics Data System (ADS)

Smith, V.

2000-11-01

This report documents the development of analytical techniques required for interpreting and comparing space systems electromagnetic interference test data with commercial electromagnetic interference test data using NASA Specification SSP 30237A "Space Systems Electromagnetic Emission and Susceptibility Requirements for Electromagnetic Compatibility." The PSpice computer simulation results and the laboratory measurements for the test setups under study compare well. The study results, however, indicate that the transfer function required to translate test results of one setup to another is highly dependent on cables and their actual layout in the test setup. Since cables are equipment specific and are not specified in the test standards, developing a transfer function that would cover all cable types (random, twisted, or coaxial), sizes (gauge number and length), and layouts (distance from the ground plane) is not practical.

Comparison of Commercial Electromagnetic Interface Test Techniques to NASA Electromagnetic Interference Test Techniques

NASA Technical Reports Server (NTRS)

Smith, V.; Minor, J. L. (Technical Monitor)

2000-01-01

This report documents the development of analytical techniques required for interpreting and comparing space systems electromagnetic interference test data with commercial electromagnetic interference test data using NASA Specification SSP 30237A "Space Systems Electromagnetic Emission and Susceptibility Requirements for Electromagnetic Compatibility." The PSpice computer simulation results and the laboratory measurements for the test setups under study compare well. The study results, however, indicate that the transfer function required to translate test results of one setup to another is highly dependent on cables and their actual layout in the test setup. Since cables are equipment specific and are not specified in the test standards, developing a transfer function that would cover all cable types (random, twisted, or coaxial), sizes (gauge number and length), and layouts (distance from the ground plane) is not practical.

Modulation transfer function measurement technique for small-pixel detectors

NASA Technical Reports Server (NTRS)

Marchywka, Mike; Socker, Dennis G.

1992-01-01

A modulation transfer function (MTF) measurement technique suitable for large-format, small-pixel detector characterization has been investigated. A volume interference grating is used as a test image instead of the bar or sine wave target images normally used. This technique permits a high-contrast, large-area, sinusoidal intensity distribution to illuminate the device being tested, avoiding the need to deconvolve raw data with imaging system characteristics. A high-confidence MTF result at spatial frequencies near 200 cycles/mm is obtained. We present results at several visible light wavelengths with a 6.8-micron-pixel CCD. Pixel response functions are derived from the MTF results.

Causal transfer function analysis to describe closed loop interactions between cardiovascular and cardiorespiratory variability signals.

PubMed

Faes, L; Porta, A; Cucino, R; Cerutti, S; Antolini, R; Nollo, G

2004-06-01

Although the concept of transfer function is intrinsically related to an input-output relationship, the traditional and widely used estimation method merges both feedback and feedforward interactions between the two analyzed signals. This limitation may endanger the reliability of transfer function analysis in biological systems characterized by closed loop interactions. In this study, a method for estimating the transfer function between closed loop interacting signals was proposed and validated in the field of cardiovascular and cardiorespiratory variability. The two analyzed signals x and y were described by a bivariate autoregressive model, and the causal transfer function from x to y was estimated after imposing causality by setting to zero the model coefficients representative of the reverse effects from y to x. The method was tested in simulations reproducing linear open and closed loop interactions, showing a better adherence of the causal transfer function to the theoretical curves with respect to the traditional approach in presence of non-negligible reverse effects. It was then applied in ten healthy young subjects to characterize the transfer functions from respiration to heart period (RR interval) and to systolic arterial pressure (SAP), and from SAP to RR interval. In the first two cases, the causal and non-causal transfer function estimates were comparable, indicating that respiration, acting as exogenous signal, sets an open loop relationship upon SAP and RR interval. On the contrary, causal and traditional transfer functions from SAP to RR were significantly different, suggesting the presence of a considerable influence on the opposite causal direction. Thus, the proposed causal approach seems to be appropriate for the estimation of parameters, like the gain and the phase lag from SAP to RR interval, which have a large clinical and physiological relevance.

Naming and Categorization in Young Children: IV: Listener Behavior Training and Transfer of Function

PubMed Central

Horne, Pauline J; Hughes, J. Carl; Lowe, C. Fergus

2006-01-01

Following pretraining with everyday objects, 14 children aged from 1 to 4 years were trained, for each of three pairs of different arbitrary wooden shapes (Set 1), to select one stimulus in response to the spoken word /zog/, and the other to /vek/. When given a test for the corresponding tacts (“zog” and “vek”), 10 children passed, showing that they had learned common names for the stimuli, and 4 failed. All children were trained to clap to one stimulus of Pair 1 and wave to the other. All those who named showed either transfer of the novel functions to the remaining two pairs of stimuli in Test 1, or novel function comprehension for all three pairs in Test 2, or both. Three of these children next participated in, and passed, category match-to-sample tests. In contrast, all 4 children who had learned only listener behavior failed both the category transfer and category match-to-sample tests. When 3 of them were next trained to name the stimuli, they passed the category transfer and (for the 2 subjects tested) category match-to-sample tests. Three children were next trained on the common listener relations with another set of arbitrary stimuli (Set 2); all succeeded on the tact and category tests with the Set 2 stimuli. Taken together with the findings from the other studies in the series, the present experiment shows that (a) common listener training also establishes the corresponding names in some but not all children, and (b) only children who learn common names categorize; all those who learn only listener behavior fail. This is good evidence in support of the naming account of categorization. PMID:16673828

Transfer of Learning Relates to Intrinsic Connectivity between Hippocampus, Ventromedial Prefrontal Cortex, and Large-Scale Networks

PubMed Central

Gerraty, Raphael T.; Davidow, Juliet Y.; Wimmer, G. Elliott; Kahn, Itamar

2014-01-01

An important aspect of adaptive learning is the ability to flexibly use past experiences to guide new decisions. When facing a new decision, some people automatically leverage previously learned associations, while others do not. This variability in transfer of learning across individuals has been demonstrated repeatedly and has important implications for understanding adaptive behavior, yet the source of these individual differences remains poorly understood. In particular, it is unknown why such variability in transfer emerges even among homogeneous groups of young healthy participants who do not vary on other learning-related measures. Here we hypothesized that individual differences in the transfer of learning could be related to relatively stable differences in intrinsic brain connectivity, which could constrain how individuals learn. To test this, we obtained a behavioral measure of memory-based transfer outside of the scanner and on a separate day acquired resting-state functional MRI images in 42 participants. We then analyzed connectivity across independent component analysis-derived brain networks during rest, and tested whether intrinsic connectivity in learning-related networks was associated with transfer. We found that individual differences in transfer were related to intrinsic connectivity between the hippocampus and the ventromedial prefrontal cortex, and between these regions and large-scale functional brain networks. Together, the findings demonstrate a novel role for intrinsic brain dynamics in flexible learning-guided behavior, both within a set of functionally specific regions known to be important for learning, as well as between these regions and the default and frontoparietal networks, which are thought to serve more general cognitive functions. PMID:25143610

Flight Controllability Limits and Related Human Transfer Functions as Determined from Simulator and Flight Tests

NASA Technical Reports Server (NTRS)

Taylor, Lawrence W., Jr.; Day, Richard E.

1961-01-01

A simulator study and flight tests were performed to determine the levels of static stability and damping necessary to enable a pilot to control the longitudinal and lateral-directional dynamics of a vehicle for short periods of time. Although a basic set of aerodynamic characteristics was used, the study was conducted so that the results would be applicable to a wide range of flight conditions and configurations. Novel piloting techniques were found which enabled the pilot to control the vehicle at conditions that were otherwise uncontrollable. The influence of several critical factors in altering the controllability limits was also investigated. Several human transfer functions were used which gave fairly good representations of the controllability limits determined experimentally for the short-period longitudinal, directional, and lateral modes. A transfer function with approximately the same gain and phase angle as the pilot at the controlling frequencies along the controllability limits was also derived.

Revealed and stated preference valuation and transfer: A within-sample comparison of water quality improvement values

NASA Astrophysics Data System (ADS)

Ferrini, Silvia; Schaafsma, Marije; Bateman, Ian

2014-06-01

Benefit transfer (BT) methods are becoming increasingly important for environmental policy, but the empirical findings regarding transfer validity are mixed. A novel valuation survey was designed to obtain both stated preference (SP) and revealed preference (RP) data concerning river water quality values from a large sample of households. Both dichotomous choice and payment card contingent valuation (CV) and travel cost (TC) data were collected. Resulting valuations were directly compared and used for BT analyses using both unit value and function transfer approaches. WTP estimates are found to pass the convergence validity test. BT results show that the CV data produce lower transfer errors, below 20% for both unit value and function transfer, than TC data especially when using function transfer. Further, comparison of WTP estimates suggests that in all cases, differences between methods are larger than differences between study areas. Results show that when multiple studies are available, using welfare estimates from the same area but based on a different method consistently results in larger errors than transfers across space keeping the method constant.

Characterization and Comparison of Vibration Transfer Paths in a Helicopter Gearbox and a Fixture Mounted Gearbox

NASA Technical Reports Server (NTRS)

Islam, Akm Anwarul; Dempsey, Paula J.; Feldman, Jason; Larsen, Chris

2014-01-01

Health monitoring of rotorcraft components, currently being performed by Health and Usage Monitoring Systems through analyses of vibration signatures of dynamic mechanical components, is very important for their safe and economic operation. HUMS analyze vibration signatures associated with faults and quantify them as condition indicators to predict component behavior. Vibration transfer paths are characterized by frequency response functions derived from the input/output relationship between applied force and dynamic response through a structure as a function of frequency. With an objective to investigate the differences in transfer paths, transfer path measurements were recorded under similar conditions in the left and right nose gearboxes of an AH-64 helicopter and in an isolated left nose gearbox in a test fixture at NASA Glenn Research Center. The test fixture enabled the application of measured torques-common during an actual operation. An impact hammer as well as commercial and lab piezo shakers, were used in conjunction with two types of commercially available accelerometers to collect the vibration response under various test conditions. The frequency response functions measured under comparable conditions of both systems were found to be consistent. Measurements made on the fixture indicated certain real-world installation and maintenance issues, such as sensor alignments, accelerometer locations and installation torques, had minimal effect. However, gear vibration transfer path dynamics appeared to be somewhat dependent on the presence of oil, and the transfer path dynamics were notably different if the force input was on the internal ring gear rather than on the external gearbox case.

Development and evaluation of the impulse transfer function technique

NASA Technical Reports Server (NTRS)

Mantus, M.

1972-01-01

The development of the test/analysis technique known as the impulse transfer function (ITF) method is discussed. This technique, when implemented with proper data processing systems, should become a valuable supplement to conventional dynamic testing and analysis procedures that will be used in the space shuttle development program. The method can relieve many of the problems associated with extensive and costly testing of the shuttle for transient loading conditions. In addition, the time history information derived from impulse testing has the potential for being used to determine modal data for the structure under investigation. The technique could be very useful in determining the time-varying modal characteristics of structures subjected to thermal transients, where conventional mode surveys are difficult to perform.

Effect of color on pilot performance and transfer functions using a full-spectrum, calligraphic, color display system

NASA Technical Reports Server (NTRS)

Chase, W. D.

1976-01-01

The use of blue and red color in out-of-window cockpit displays, in full-spectrum calligraphic computer-generated display systems, is studied with attention given to pilot stereographic depth perception and response to visual cues. Displays for vertical approach, with dynamic and frozen-range landing approach and perspective arrays, are analyzed. Pilot transfer function and the transfer function associated with the contrasted approach and perspective arrays are discussed. Out-of-window blue lights are perceived by pilots as indicating greater distance depth, red lights as indicating proximity. The computer-generated chromatic display was adapted to flight simulators for the tests.

Dynamic Stiffness Transfer Function of an Electromechanical Actuator Using System Identification

NASA Astrophysics Data System (ADS)

Kim, Sang Hwa; Tahk, Min-Jea

2018-04-01

In the aeroelastic analysis of flight vehicles with electromechanical actuators (EMAs), an accurate prediction of flutter requires dynamic stiffness characteristics of the EMA. The dynamic stiffness transfer function of the EMA with brushless direct current (BLDC) motor can be obtained by conducting complicated mathematical calculations of control algorithms and mechanical/electrical nonlinearities using linearization techniques. Thus, system identification approaches using experimental data, as an alternative, have considerable advantages. However, the test setup for system identification is expensive and complex, and experimental procedures for data collection are time-consuming tasks. To obtain the dynamic stiffness transfer function, this paper proposes a linear system identification method that uses information obtained from a reliable dynamic stiffness model with a control algorithm and nonlinearities. The results of this study show that the system identification procedure is compact, and the transfer function is able to describe the dynamic stiffness characteristics of the EMA. In addition, to verify the validity of the system identification method, the simulation results of the dynamic stiffness transfer function and the dynamic stiffness model were compared with the experimental data for various external loads.

Accounting for substitution and spatial heterogeneity in a labelled choice experiment.

PubMed

Lizin, S; Brouwer, R; Liekens, I; Broeckx, S

2016-10-01

Many environmental valuation studies using stated preferences techniques are single-site studies that ignore essential spatial aspects, including possible substitution effects. In this paper substitution effects are captured explicitly in the design of a labelled choice experiment and the inclusion of different distance variables in the choice model specification. We test the effect of spatial heterogeneity on welfare estimates and transfer errors for minor and major river restoration works, and the transferability of river specific utility functions, accounting for key variables such as site visitation, spatial clustering and income. River specific utility functions appear to be transferable, resulting in low transfer errors. However, ignoring spatial heterogeneity increases transfer errors. Copyright © 2016 Elsevier Ltd. All rights reserved.

Latissimus dorsi transfer for irreparable subscapularis tendon tears.

PubMed

Mun, Sang Won; Kim, Ji Young; Yi, Seung Hoon; Baek, Chang Hee

2018-06-01

There are several tendon transfers for reconstruction of irreparable subscapularis tears. The latissimus dorsi (LD) could be used because its direction and function are similar to those of the subscapularis. We performed LD transfers for irreparable subscapularis tears and evaluated clinical outcomes. The study enrolled 24 consecutive patients who underwent LD transfers. Clinical and functional outcomes were evaluated using the Constant score, American Shoulder and Elbow Surgeons score, pain visual analog scale, and range of shoulder motion preoperatively and at last follow-up. The lift-off and belly-press tests were performed to assess subscapularis integrity and function. Magnetic resonance imaging was performed preoperatively and 1 year postoperatively to evaluate tendon integrity. Mean Constant, American Shoulder and Elbow Surgeons, and pain scores improved from 46 ± 6 to 69 ± 5 (P < .001), from 40 ± 3 to 70 ± 5 (P < .001), and from 6 ± 1 to 2 ± 1 (P = .006), respectively. The mean range of motion for forward elevation and internal rotation increased from 135° ± 17° to 166° ± 15° (P = .016) and from L5 to L1 (P = .010), respectively. Improvement in the range of motion for external rotation was not significant (51° ± 7° to 68° ± 7°; P = .062). At final follow-up, the belly-press test results were negative for 18 of 24 patients, and the lift-off test results were negative for 16 of 20 patients. No complications related to tendon transfer, including axillary and radial nerve injuries, were found. No retearing of the transferred LD was observed. LD transfer resulted in pain relief and restoration of shoulder range of motion and function. LD transfer could be considered an effective and safe salvage treatment for irreparable subscapularis tears. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Direct repeat sequences are essential for function of the cis-acting locus of transfer (clt) of Streptomyces phaeochromogenes plasmid pJV1.

PubMed

Franco, Bernardo; González-Cerón, Gabriela; Servín-González, Luis

2003-11-01

The functionality of direct and inverted repeat sequences inside the cis acting locus of transfer (clt) of the Streptomyces plasmid pJV1 was determined by testing the effect of different deletions on plasmid transfer. The results show that the single most important element for pJV1 clt function is a series of evenly spaced 9 bp long direct repeats which match the consensus CCGCACA(C/G)(C/G), since their deletion caused a dramatic reduction in plasmid transfer. The presence of these repeats in the absence of any other clt sequences allowed plasmid transfer to occur at a frequency that was at least two orders of magnitude higher than that obtained in the complete absence of clt. A database search revealed regions with a similar organization, and in the same position, in Streptomyces plasmids pSN22 and pSLS, which have transfer proteins homologous to those of pJV1.

Dynamics of cavitating cascades. [transfer functions

NASA Technical Reports Server (NTRS)

Brennen, C. E.; Acosta, A. J.

1980-01-01

The unsteady dynamics of cavitating cascades and inducer pumps were studied with a view to understanding (and possibly predicting) the dynamic characteristics of these devices. The chronology of the research is summarized as well as the final conculsions for each task. The construction of a dynamic pump test facility and its use in making experimental measurements of the transfer function is described as well as tests conducted using a scale model of the low pressure liquid oxygen turbopump inducer in the shuttle main engine. Auto-oscillation and unsteady inlet flow characteristics are discussed in addition to blade cavity influence and bubbly cavitation.

Subcooled forced convection boiling of trichlorotrifluoroethane

NASA Technical Reports Server (NTRS)

Dougall, R. S.; Panian, D. J.

1972-01-01

Experimental heat-transfer data were obtained for the forced-convection boiling of trichlorotrifluoroethane (R-113 or Freon-113) in a vertical annular test annular test section. The 97 data points obtained covered heat transfer by forced convection, local boiling, and fully-developed boiling. Correlating methods were obtained which accurately predicted the heat flux as a function of wall superheat (boiling curve) over the range of parameters studied.

Methodology Investigation of AI(Artificial Intelligence) Test Officer Support Tool. Volume 2

DTIC Science & Technology

1989-03-01

a mathematical representation of a PE and its connections. This representation describes the " neurodynamics " of a PE. A sigmoid transfer function is...Element(i) Neurodynamics : Summation Function: Wo*XO + W,*X + W*X "X 0 0 1 1 2 W~fn Transfer Function: F(k) = (1 + e k) Output: x. - F(I) Figure 2-4...simplifies the description of the network operations. Thus, one or more PEs grouped together, with the same neurodynamics , is a layer [reference 5]. A

Transfer of learning relates to intrinsic connectivity between hippocampus, ventromedial prefrontal cortex, and large-scale networks.

PubMed

Gerraty, Raphael T; Davidow, Juliet Y; Wimmer, G Elliott; Kahn, Itamar; Shohamy, Daphna

2014-08-20

An important aspect of adaptive learning is the ability to flexibly use past experiences to guide new decisions. When facing a new decision, some people automatically leverage previously learned associations, while others do not. This variability in transfer of learning across individuals has been demonstrated repeatedly and has important implications for understanding adaptive behavior, yet the source of these individual differences remains poorly understood. In particular, it is unknown why such variability in transfer emerges even among homogeneous groups of young healthy participants who do not vary on other learning-related measures. Here we hypothesized that individual differences in the transfer of learning could be related to relatively stable differences in intrinsic brain connectivity, which could constrain how individuals learn. To test this, we obtained a behavioral measure of memory-based transfer outside of the scanner and on a separate day acquired resting-state functional MRI images in 42 participants. We then analyzed connectivity across independent component analysis-derived brain networks during rest, and tested whether intrinsic connectivity in learning-related networks was associated with transfer. We found that individual differences in transfer were related to intrinsic connectivity between the hippocampus and the ventromedial prefrontal cortex, and between these regions and large-scale functional brain networks. Together, the findings demonstrate a novel role for intrinsic brain dynamics in flexible learning-guided behavior, both within a set of functionally specific regions known to be important for learning, as well as between these regions and the default and frontoparietal networks, which are thought to serve more general cognitive functions. Copyright © 2014 the authors 0270-6474/14/3411297-07$15.00/0.

Transferring embryos with genetic anomalies detected in preimplantation testing: an Ethics Committee Opinion.

PubMed

2017-05-01

Patient requests for transfer of embryos with genetic anomalies linked to serious health-affecting disorders detected in preimplantation testing are rare but do exist. This Opinion sets out the possible rationales for a provider's decision to assist or decline to assist in such transfers. The Committee concludes in most clinical cases it is ethically permissible to assist or decline to assist in transferring such embryos. In circumstances in which a child is highly likely to be born with a life-threatening condition that causes severe and early debility with no possibility of reasonable function, provider transfer of such embryos is ethically problematic and highly discouraged. Copyright © 2017 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Influence of the type of training task on intermanual transfer effects in upper-limb prosthesis training: A randomized pre-posttest study.

PubMed

Romkema, Sietske; Bongers, Raoul M; van der Sluis, Corry K

2017-01-01

Intermanual transfer, the transfer of motor skills from the trained hand to the untrained hand, can be used to train upper limb prosthesis skills. The aim of this study was to determine the relation between the magnitude of the intermanual transfer effect and the type of training task. The used tasks were based on different aspects of prosthetic handling: reaching, grasping, grip-force production and functional tasks. A single-blinded clinical trial, with a pre-posttest design was executed. Seventy-one able-bodied, right-handed participants were randomly assigned to four training and two control groups. The training groups performed a training program with an upper-limb prosthesis simulator. One control group performed a sham training (a dummy training without the prosthesis simulator) and another control group received no training at all. The training groups and sham group trained on five consecutive days. To determine the improvement in skills, a test was administered before, immediately after, and one week after the training. Training was performed with the 'unaffected' arm; tests were performed with the 'affected' arm, with the latter resembling the amputated limb. In this study half of the participants trained with the dominant hand, while the other half trained with the non-dominant hand. Participants executed four tests that corresponded to the different training tasks. The tests measured the reaching (movement time and symmetry ratio), grasping (opening time, duration of maximum hand opening, and closing time), grip-force production (deviation of asked grip-force) and functional (movement time) performance. Half of the participants were tested with their dominant arm and half of the participants with their non-dominant arm. Intermanual transfer effects were not found for reaching, grasping or functional tasks. However, we did find intermanual transfer effects for grip-force production tasks. Possibly, the study design contributed to the negative results due to the duration of the training sessions and test sessions. The positive results of the grip-force production might be an effect of the specificity of the training, that was totally focused on training grip-force production. When using intermanual transfer training in novice amputees, specific training should be devoted to grip-force.

Influence of the type of training task on intermanual transfer effects in upper-limb prosthesis training: A randomized pre-posttest study

PubMed Central

Romkema, Sietske; Bongers, Raoul M.; van der Sluis, Corry K.

2017-01-01

Intermanual transfer, the transfer of motor skills from the trained hand to the untrained hand, can be used to train upper limb prosthesis skills. The aim of this study was to determine the relation between the magnitude of the intermanual transfer effect and the type of training task. The used tasks were based on different aspects of prosthetic handling: reaching, grasping, grip-force production and functional tasks. A single-blinded clinical trial, with a pre-posttest design was executed. Seventy-one able-bodied, right-handed participants were randomly assigned to four training and two control groups. The training groups performed a training program with an upper-limb prosthesis simulator. One control group performed a sham training (a dummy training without the prosthesis simulator) and another control group received no training at all. The training groups and sham group trained on five consecutive days. To determine the improvement in skills, a test was administered before, immediately after, and one week after the training. Training was performed with the ‘unaffected’ arm; tests were performed with the ‘affected’ arm, with the latter resembling the amputated limb. In this study half of the participants trained with the dominant hand, while the other half trained with the non-dominant hand. Participants executed four tests that corresponded to the different training tasks. The tests measured the reaching (movement time and symmetry ratio), grasping (opening time, duration of maximum hand opening, and closing time), grip-force production (deviation of asked grip-force) and functional (movement time) performance. Half of the participants were tested with their dominant arm and half of the participants with their non-dominant arm. Intermanual transfer effects were not found for reaching, grasping or functional tasks. However, we did find intermanual transfer effects for grip-force production tasks. Possibly, the study design contributed to the negative results due to the duration of the training sessions and test sessions. The positive results of the grip-force production might be an effect of the specificity of the training, that was totally focused on training grip-force production. When using intermanual transfer training in novice amputees, specific training should be devoted to grip-force. PMID:29190727

Vent System Analysis for the Cryogenic Propellant Storage Transfer Ground Test Article

NASA Technical Reports Server (NTRS)

Hedayat, A

2013-01-01

To test and validate key capabilities and technologies required for future exploration elements such as large cryogenic propulsion stages and propellant depots, NASA is leading the efforts to develop and design the Cryogenic Propellant Storage and Transfer (CPST) Cryogenic Fluid Management (CFM) payload. The primary objectives of CPST payload are to demonstrate: 1) in-space storage of cryogenic propellants for long duration applications; and 2) in-space transfer of cryogenic propellants. The Ground Test Article (GTA) is a technology development version of the CPST payload. The GTA consists of flight-sized and flight-like storage and transfer tanks, liquid acquisition devices, transfer, and pressurization systems with all of the CPST functionality. The GTA is designed to perform integrated passive and active thermal storage and transfer performance testing with liquid hydrogen (LH2) in a vacuum environment. The GTA storage tank is designed to store liquid hydrogen and the transfer tank is designed to be 5% of the storage tank volume. The LH2 transfer subsystem is designed to transfer propellant from one tank to the other utilizing pressure or a pump. The LH2 vent subsystem is designed to prevent over-pressurization of the storage and transfer tanks. An in-house general-purpose computer program was utilized to model and simulate the vent subsystem operation. The modeling, analysis, and the results will be presented in the final paper.

TRANSFER OF AVERSIVE RESPONDENT ELICITATION IN ACCORDANCE WITH EQUIVALENCE RELATIONS

PubMed Central

Valverde, Miguel RodrÍguez; Luciano, Carmen; Barnes-Holmes, Dermot

2009-01-01

The present study investigates the transfer of aversively conditioned respondent elicitation through equivalence classes, using skin conductance as the measure of conditioning. The first experiment is an attempt to replicate Experiment 1 in Dougher, Augustson, Markham, Greenway, and Wulfert (1994), with different temporal parameters in the aversive conditioning procedure employed. Match-to-sample procedures were used to teach 17 participants two 4-member equivalence classes. Then, one member of one class was paired with electric shock and one member of the other class was presented without shock. The remaining stimuli from each class were presented in transfer tests. Unlike the findings in the original study, transfer of conditioning was not achieved. In Experiment 2, similar procedures were used with 30 participants, although several modifications were introduced (formation of five-member classes, direct conditioning with several elements of each class, random sequences of stimulus presentation in transfer tests, reversal in aversive conditioning contingencies). More than 80% of participants who had shown differential conditioning also showed the transfer of function effect. Moreover, this effect was replicated within subjects for 3 participants. This is the first demonstration of the transfer of aversive respondent elicitation through stimulus equivalence classes with the presentation of transfer test trials in random order. The latter prevents the possibility that transfer effects are an artefact of transfer test presentation order. PMID:20119523

Transferability of species distribution models: a functional habitat approach for two regionally threatened butterflies.

PubMed

Vanreusel, Wouter; Maes, Dirk; Van Dyck, Hans

2007-02-01

Numerous models for predicting species distribution have been developed for conservation purposes. Most of them make use of environmental data (e.g., climate, topography, land use) at a coarse grid resolution (often kilometres). Such approaches are useful for conservation policy issues including reserve-network selection. The efficiency of predictive models for species distribution is usually tested on the area for which they were developed. Although highly interesting from the point of view of conservation efficiency, transferability of such models to independent areas is still under debate. We tested the transferability of habitat-based predictive distribution models for two regionally threatened butterflies, the green hairstreak (Callophrys rubi) and the grayling (Hipparchia semele), within and among three nature reserves in northeastern Belgium. We built predictive models based on spatially detailed maps of area-wide distribution and density of ecological resources. We used resources directly related to ecological functions (host plants, nectar sources, shelter, microclimate) rather than environmental surrogate variables. We obtained models that performed well with few resource variables. All models were transferable--although to different degrees--among the independent areas within the same broad geographical region. We argue that habitat models based on essential functional resources could transfer better in space than models that use indirect environmental variables. Because functional variables can easily be interpreted and even be directly affected by terrain managers, these models can be useful tools to guide species-adapted reserve management.

Description of the docking module ECS for the Apollo-Soyuz Test Project.

NASA Technical Reports Server (NTRS)

Guy, W. W.; Jaax, J. R.

1973-01-01

The role of the Docking Module ECS (Environmental Control System) to be used on the Apollo-Soyuz Test mission is to provide a means for crewmen to transfer safely between the Apollo and Soyuz vehicles in a shirtsleeve environment. This paper describes the Docking Module ECS and includes the philosophy and rationale used in evaluating and selecting the capabilities that are required to satisfy the Docking Module's airlock function: (1) adjusting the pressure and composition of the atmosphere to effect crew transfer and (2) providing a shirtsleeve environment during transfer operations. An analytical evaluation is given of the environmental parameters (including CO2 level, humidity, and temperature) during a normal transfer timeline.

Consistent Parameter and Transfer Function Estimation using Context Free Grammars

NASA Astrophysics Data System (ADS)

Klotz, Daniel; Herrnegger, Mathew; Schulz, Karsten

2017-04-01

This contribution presents a method for the inference of transfer functions for rainfall-runoff models. Here, transfer functions are defined as parametrized (functional) relationships between a set of spatial predictors (e.g. elevation, slope or soil texture) and model parameters. They are ultimately used for estimation of consistent, spatially distributed model parameters from a limited amount of lumped global parameters. Additionally, they provide a straightforward method for parameter extrapolation from one set of basins to another and can even be used to derive parameterizations for multi-scale models [see: Samaniego et al., 2010]. Yet, currently an actual knowledge of the transfer functions is often implicitly assumed. As a matter of fact, for most cases these hypothesized transfer functions can rarely be measured and often remain unknown. Therefore, this contribution presents a general method for the concurrent estimation of the structure of transfer functions and their respective (global) parameters. Note, that by consequence an estimation of the distributed parameters of the rainfall-runoff model is also undertaken. The method combines two steps to achieve this. The first generates different possible transfer functions. The second then estimates the respective global transfer function parameters. The structural estimation of the transfer functions is based on the context free grammar concept. Chomsky first introduced context free grammars in linguistics [Chomsky, 1956]. Since then, they have been widely applied in computer science. But, to the knowledge of the authors, they have so far not been used in hydrology. Therefore, the contribution gives an introduction to context free grammars and shows how they can be constructed and used for the structural inference of transfer functions. This is enabled by new methods from evolutionary computation, such as grammatical evolution [O'Neill, 2001], which make it possible to exploit the constructed grammar as a search space for equations. The parametrization of the transfer functions is then achieved through a second optimization routine. The contribution explores different aspects of the described procedure through a set of experiments. These experiments can be divided into three categories: (1) The inference of transfer functions from directly measurable parameters; (2) The estimation of global parameters for given transfer functions from runoff data; and (3) The estimation of sets of completely unknown transfer functions from runoff data. The conducted tests reveal different potentials and limits of the procedure. In concrete it is shown that example (1) and (2) work remarkably well. Example (3) is much more dependent on the setup. In general, it can be said that in that case much more data is needed to derive transfer function estimations, even for simple models and setups. References: - Chomsky, N. (1956): Three Models for the Description of Language. IT IRETr. 2(3), p 113-124 - O'Neil, M. (2001): Grammatical Evolution. IEEE ToEC, Vol.5, No. 4 - Samaniego, L.; Kumar, R.; Attinger, S. (2010): Multiscale parameter regionalization of a grid-based hydrologic model at the mesoscale. WWR, Vol. 46, W05523, doi:10.1029/2008WR007327

Binaural Simulation Experiments in the NASA Langley Structural Acoustics Loads and Transmission Facility

NASA Technical Reports Server (NTRS)

Grosveld, Ferdinand W.; Silcox, Richard (Technical Monitor)

2001-01-01

A location and positioning system was developed and implemented in the anechoic chamber of the Structural Acoustics Loads and Transmission (SALT) facility to accurately determine the coordinates of points in three-dimensional space. Transfer functions were measured between a shaker source at two different panel locations and the vibrational response distributed over the panel surface using a scanning laser vibrometer. The binaural simulation test matrix included test runs for several locations of the measuring microphones, various attitudes of the mannequin, two locations of the shaker excitation and three different shaker inputs including pulse, broadband random, and pseudo-random. Transfer functions, auto spectra, and coherence functions were acquired for the pseudo-random excitation. Time histories were acquired for the pulse and broadband random input to the shaker. The tests were repeated with a reflective surface installed. Binary data files were converted to universal format and archived on compact disk.

Dynamic response of NASA Rotor Test Apparatus and Sikorsky S-76 hub mounted in the 80- by 120-Foot Wind Tunnel

NASA Technical Reports Server (NTRS)

Peterson, Randall L.; Hoque, Muhammed S.

1994-01-01

A shake test was conducted in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center, using the NASA Ames Rotor Test Apparatus (RTA) and the Sikorsky S-76 rotor hub. The primary objective of this shake test was to determine the modal properties of the RTA, the S-76 rotor hub, and the model support system installed in the wind tunnel. Random excitation was applied at the rotor hub, and vibration responses were measured using accelerometers mounted at various critical locations on the model and the model support system. Transfer functions were computed using the load cell data and the accelerometer responses. The transfer function data were used to compute the system modal parameters with the aid of modal analysis software.

Development of a new pan-European testate amoeba transfer function for reconstructing peatland palaeohydrology

NASA Astrophysics Data System (ADS)

Amesbury, Matthew J.; Swindles, Graeme T.; Bobrov, Anatoly; Charman, Dan J.; Holden, Joseph; Lamentowicz, Mariusz; Mallon, Gunnar; Mazei, Yuri; Mitchell, Edward A. D.; Payne, Richard J.; Roland, Thomas P.; Turner, T. Edward; Warner, Barry G.

2016-11-01

In the decade since the first pan-European testate amoeba-based transfer function for peatland palaeohydrological reconstruction was published, a vast amount of additional data collection has been undertaken by the research community. Here, we expand the pan-European dataset from 128 to 1799 samples, spanning 35° of latitude and 55° of longitude. After the development of a new taxonomic scheme to permit compilation of data from a wide range of contributors and the removal of samples with high pH values, we developed ecological transfer functions using a range of model types and a dataset of ∼1300 samples. We rigorously tested the efficacy of these models using both statistical validation and independent test sets with associated instrumental data. Model performance measured by statistical indicators was comparable to other published models. Comparison to test sets showed that taxonomic resolution did not impair model performance and that the new pan-European model can therefore be used as an effective tool for palaeohydrological reconstruction. Our results question the efficacy of relying on statistical validation of transfer functions alone and support a multi-faceted approach to the assessment of new models. We substantiated recent advice that model outputs should be standardised and presented as residual values in order to focus interpretation on secure directional shifts, avoiding potentially inaccurate conclusions relating to specific water-table depths. The extent and diversity of the dataset highlighted that, at the taxonomic resolution applied, a majority of taxa had broad geographic distributions, though some morphotypes appeared to have restricted ranges.

Parameter Estimation of Actuators for Benchmark Active Control Technology (BACT) Wind Tunnel Model with Analysis of Wear and Aerodynamic Loading Effects

NASA Technical Reports Server (NTRS)

Waszak, Martin R.; Fung, Jimmy

1998-01-01

This report describes the development of transfer function models for the trailing-edge and upper and lower spoiler actuators of the Benchmark Active Control Technology (BACT) wind tunnel model for application to control system analysis and design. A simple nonlinear least-squares parameter estimation approach is applied to determine transfer function parameters from frequency response data. Unconstrained quasi-Newton minimization of weighted frequency response error was employed to estimate the transfer function parameters. An analysis of the behavior of the actuators over time to assess the effects of wear and aerodynamic load by using the transfer function models is also presented. The frequency responses indicate consistent actuator behavior throughout the wind tunnel test and only slight degradation in effectiveness due to aerodynamic hinge loading. The resulting actuator models have been used in design, analysis, and simulation of controllers for the BACT to successfully suppress flutter over a wide range of conditions.

Service life evaluation of rigid explosive transfer lines

NASA Technical Reports Server (NTRS)

Bement, L. J.; Kayser, E. G.; Schimmel, M. L.

1983-01-01

This paper describes a joint Army/NASA-sponsored research program on the service life evaluation of rigid explosive transfer lines. These transfer lines are used to initiate emergency crew escape functions on a wide variety of military and NASA aircraft. The purpose of this program was to determine quantitatively the effects of service, age, and degradation on rigid explosive transfer lines to allow responsible, conservative, service life determination. More than 800 transfer lines were removed from the U.S. Army AH-1G and AH-1S, the U.S. Air Force B-1 and F-111, and the U.S. Navy F-14 aircraft for testing. The results indicated that the lines were not adversely affected by age, service, or a repeat of the thermal qualification tests on full-service lines. Extension of the service life of rigid explosive transfer lines should be considered, since considerable cost savings could be realized with no measurable decrease in system reliability.

The Mediating Role of Insight for Long-Term Improvements in Psychodynamic Therapy

ERIC Educational Resources Information Center

Johansson, Paul; Hoglend, Per; Ulberg, Randi; Amlo, Svein; Marble, Alice; Bogwald, Kjell-Petter; Sorbye, Oystein; Sjaastad, Mary Cosgrove; Heyerdahl, Oscar

2010-01-01

Objective: According to psychoanalytic theory, interpretation of transference leads to increased insight that again leads to improved interpersonal functioning over time. In this study, we performed a full mediational analysis to test whether insight gained during treatment mediates the long-term effects of transference interpretation in dynamic…

An experimental test of whether habitat corridors affect pollen transfer.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Townsend, Patricia A.; Levey, Douglas J.

Abstract. Negative effects of habitat fragmentation are thought to be diminished when habitat patches are joined by a corridor. A key assumption is that corridors facilitate exchange rates of organisms between otherwise isolated patches. If the organisms are pollinators, corridors may be important for maintaining genetically viable populations of the plants that they pollinate. We tested the hypothesis that corridors increase the movement of insect pollinators into patches of habitat and thereby increase pollen transfer for two species of plants, one pollinated by butterflies (Lantana camara) and the other by bees and wasps (Rudbeckia hirta). We worked in an experimentalmore » landscape consisting of 40 greater than or equal to 1-ha patches of early-successional habitat in a matrix of forest. Within each of eight experimental units, two patches were connected by a corridor (150 X 25 m), and three were not. Patch shape varied to control for the area added by the presence of a corridor. Differences in patch shape also allowed us to test alternative hypotheses of how corridors might function. The Traditional Corridor Hypothesis posits that corridors increase immigration and emigration by functioning as movement conduits between patches. The Drift Fence Hypothesis posits that corridors function by ‘‘capturing’’ organisms dispersing through the matrix, redirecting them into associated habitat patches. Using fluorescent powder to track pollen, we found that pollen transfer by butterflies between patches connected by a corridor was significantly higher than between unconnected patches (all values mean plus or minus 1 SE: 59% plus or minus 9.2% vs. 25% plus or minus 5.2% of flowers receiving pollen). Likewise, pollen transfer by bees and wasps was significantly higher between connected patches than between unconnected patches (30% plus or minus 4.2% vs. 14.5% plus or minus 2.2%). These results support the Traditional Corridor Hypothesis. There was little support, however, for the Drift Fence Hypothesis. To generalize our results to a larger scale, we measured the probability of pollen transfer by butterflies as a function of distance along a 2000 X 75 m corridor. Pollen transfer probability exponentially declined with respect to distance and successfully predicted pollen transfer probability on the scale of our previous experiment. These results suggest that corridors facilitate pollen transfer in fragmented landscapes.« less

Photon-phonon-photon transfer in optomechanics

PubMed Central

Rakhubovsky, Andrey A.; Filip, Radim

2017-01-01

We consider transfer of a highly nonclassical quantum state through an optomechanical system. That is we investigate a protocol consisting of sequential upload, storage and reading out of the quantum state from a mechanical mode of an optomechanical system. We show that provided the input state is in a test-bed single-photon Fock state, the Wigner function of the recovered state can have negative values at the origin, which is a manifest of nonclassicality of the quantum state of the macroscopic mechanical mode and the overall transfer protocol itself. Moreover, we prove that the recovered state is quantum non-Gaussian for wide range of setup parameters. We verify that current electromechanical and optomechanical experiments can test this complete transfer of single photon. PMID:28436461

Thematic mapper flight model preshipment review data package. Volume 4: Appendix. Part G: Miscellaneous system data

NASA Technical Reports Server (NTRS)

1982-01-01

Functional and design data from various thematic mapper subsystems are presented. Coarse focus, modulation transfer function, and shim requirements are addressed along with spectral matching and spatial coverage tests.

14 CFR 120.109 - Types of drug testing required.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-sensitive function listed in § 120.105 unless the employer first conducts a pre-employment test and receives... conduct another pre-employment test and receive a verified negative drug test result before hiring or... pre-employment test required by paragraphs (a)(1) or (2) of this section and hiring or transferring...

14 CFR 120.109 - Types of drug testing required.

Code of Federal Regulations, 2011 CFR

2011-01-01

...-sensitive function listed in § 120.105 unless the employer first conducts a pre-employment test and receives... conduct another pre-employment test and receive a verified negative drug test result before hiring or... pre-employment test required by paragraphs (a)(1) or (2) of this section and hiring or transferring...

14 CFR 120.109 - Types of drug testing required.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-sensitive function listed in § 120.105 unless the employer first conducts a pre-employment test and receives... conduct another pre-employment test and receive a verified negative drug test result before hiring or... pre-employment test required by paragraphs (a)(1) or (2) of this section and hiring or transferring...

14 CFR 120.109 - Types of drug testing required.

Code of Federal Regulations, 2012 CFR

2012-01-01

...-sensitive function listed in § 120.105 unless the employer first conducts a pre-employment test and receives... conduct another pre-employment test and receive a verified negative drug test result before hiring or... pre-employment test required by paragraphs (a)(1) or (2) of this section and hiring or transferring...

14 CFR 120.109 - Types of drug testing required.

Code of Federal Regulations, 2010 CFR

2010-01-01

...-sensitive function listed in § 120.105 unless the employer first conducts a pre-employment test and receives... conduct another pre-employment test and receive a verified negative drug test result before hiring or... pre-employment test required by paragraphs (a)(1) or (2) of this section and hiring or transferring...

A probabilistic approach to radiative energy loss calculations for optically thick atmospheres - Hydrogen lines and continua

NASA Technical Reports Server (NTRS)

Canfield, R. C.; Ricchiazzi, P. J.

1980-01-01

An approximate probabilistic radiative transfer equation and the statistical equilibrium equations are simultaneously solved for a model hydrogen atom consisting of three bound levels and ionization continuum. The transfer equation for L-alpha, L-beta, H-alpha, and the Lyman continuum is explicitly solved assuming complete redistribution. The accuracy of this approach is tested by comparing source functions and radiative loss rates to values obtained with a method that solves the exact transfer equation. Two recent model solar-flare chromospheres are used for this test. It is shown that for the test atmospheres the probabilistic method gives values of the radiative loss rate that are characteristically good to a factor of 2. The advantage of this probabilistic approach is that it retains a description of the dominant physical processes of radiative transfer in the complete redistribution case, yet it achieves a major reduction in computational requirements.

Shear transfer capacity of reinforced concrete exposed to fire

NASA Astrophysics Data System (ADS)

Ahmad, Subhan; Bhargava, Pradeep; Chourasia, Ajay

2018-04-01

Shear transfer capacity of reinforced concrete elements is a function of concrete compressive strength and reinforcement yield strength. Exposure of concrete and steel to elevated temperature reduces their mechanical properties resulting in reduced shear transfer capacity of RC elements. The objective of present study is to find the effect of elevated temperature on shear transfer capacity of reinforced concrete. For this purpose pushoff specimens were casted using normal strength concrete. After curing, specimens were heated to 250°C and 500°C in an electric furnace. Cooled specimens were tested for shear transfer capacity in a universal testing machine. It was found that shear transfer capacity and stiffness (slope of load-slip curve) were reduced when the specimens were heated to 250°C and 500°C. Load level for the initiation of crack slip was found to be decreased as the temperature was increased. A simple analytical approach is also proposed to predict the shear transfer capacity of reinforced concrete after elevated temperature.

A multicontext approach to promoting transfer of strategy use and self regulation after brain injury: An exploratory study.

PubMed

Toglia, Joan; Johnston, Mark V; Goverover, Yael; Dain, Barry

2010-01-01

Persons with brain injury frequently demonstrate decreased ability to monitor and apply strategies learned in treatment to everyday situations. The aim of this study is to refine, explore and provide preliminary testing of the multicontext approach in promoting strategy use across situations and increasing self-regulation, awareness and functional performance. This study used a single-subject design with repeated measures pre- and post-intervention, with data analysed descriptively and graphically. Four persons with difficulty following multi-step directions, 3-5 years post-TBI, received a nine session intervention programme. Outcome measures included the Awareness Questionnaire, Self-Regulation Skills Interview, Behavior Rating Inventory of Executive Function, Multiple Errands Test and an Executive Function Performance Test sub-task. The process of change within each treatment session was examined with strategy and awareness ratings. All participants demonstrated positive changes in self-regulatory skills and strategy use that was observed across tasks. As expected, general awareness of deficits remained unchanged. Examination of individual participants revealed important, varying patterns of change in strategy use, learning transfer and self-awareness across intervention. Results provide preliminary support for the feasibility and efficacy of the multicontext approach in promoting transfer of strategy use to enhance functional performance and selective aspects of awareness. Further investigation, including a larger controlled study, is needed to confirm or limit these observations.

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

NASA Technical Reports Server (NTRS)

Brenner, Martin J.

1993-01-01

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed in this paper using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated in this paper by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-18 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

NASA Technical Reports Server (NTRS)

Brenner, Martin J.

1993-01-01

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-l8 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Tests of Exoplanet Atmospheric Radiative Transfer Codes

NASA Astrophysics Data System (ADS)

Harrington, Joseph; Challener, Ryan; DeLarme, Emerson; Cubillos, Patricio; Blecic, Jasmina; Foster, Austin; Garland, Justin

2016-10-01

Atmospheric radiative transfer codes are used both to predict planetary spectra and in retrieval algorithms to interpret data. Observational plans, theoretical models, and scientific results thus depend on the correctness of these calculations. Yet, the calculations are complex and the codes implementing them are often written without modern software-verification techniques. In the process of writing our own code, we became aware of several others with artifacts of unknown origin and even outright errors in their spectra. We present a series of tests to verify atmospheric radiative-transfer codes. These include: simple, single-line line lists that, when combined with delta-function abundance profiles, should produce a broadened line that can be verified easily; isothermal atmospheres that should produce analytically-verifiable blackbody spectra at the input temperatures; and model atmospheres with a range of complexities that can be compared to the output of other codes. We apply the tests to our own code, Bayesian Atmospheric Radiative Transfer (BART) and to several other codes. The test suite is open-source software. We propose this test suite as a standard for verifying current and future radiative transfer codes, analogous to the Held-Suarez test for general circulation models. This work was supported by NASA Planetary Atmospheres grant NX12AI69G and NASA Astrophysics Data Analysis Program grant NNX13AF38G.

Analysis of an electrohydraulic aircraft control surface servo and comparison with test results

NASA Technical Reports Server (NTRS)

Edwards, J. W.

1972-01-01

An analysis of an electrohydraulic aircraft control-surface system is made in which the system is modeled as a lumped, two-mass, spring-coupled system controlled by a servo valve. Both linear and nonlinear models are developed, and the effects of hinge-moment loading are included. Transfer functions of the system and approximate literal factors of the transfer functions for several cases are presented. The damping action of dynamic pressure feedback is analyzed. Comparisons of the model responses with results from tests made on a highly resonant rudder control-surface servo indicate the adequacy of the model. The effects of variations in hinge-moment loading are illustrated.

The 32nd CDC: System identification using interval dynamic models

NASA Technical Reports Server (NTRS)

Keel, L. H.; Lew, J. S.; Bhattacharyya, S. P.

1992-01-01

Motivated by the recent explosive development of results in the area of parametric robust control, a new technique to identify a family of uncertain systems is identified. The new technique takes the frequency domain input and output data obtained from experimental test signals and produces an 'interval transfer function' that contains the complete frequency domain behavior with respect to the test signals. This interval transfer function is one of the key concepts in the parametric robust control approach and identification with such an interval model allows one to predict the worst case performance and stability margins using recent results on interval systems. The algorithm is illustrated by applying it to an 18 bay Mini-Mast truss structure.

Testing and development of transfer functions for weighing precipitation gauges in WMO-SPICE

NASA Astrophysics Data System (ADS)

Kochendorfer, John; Nitu, Rodica; Wolff, Mareile; Mekis, Eva; Rasmussen, Roy; Baker, Bruce; Earle, Michael E.; Reverdin, Audrey; Wong, Kai; Smith, Craig D.; Yang, Daqing; Roulet, Yves-Alain; Meyers, Tilden; Buisan, Samuel; Isaksen, Ketil; Brækkan, Ragnar; Landolt, Scott; Jachcik, Al

2018-02-01

Weighing precipitation gauges are used widely for the measurement of all forms of precipitation, and are typically more accurate than tipping-bucket precipitation gauges. This is especially true for the measurement of solid precipitation; however, weighing precipitation gauge measurements must still be adjusted for undercatch in snowy, windy conditions. In WMO-SPICE (World Meteorological Organization Solid Precipitation InterComparison Experiment), different types of weighing precipitation gauges and shields were compared, and adjustments were determined for the undercatch of solid precipitation caused by wind. For the various combinations of gauges and shields, adjustments using both new and previously existing transfer functions were evaluated. For most of the gauge and shield combinations, previously derived transfer functions were found to perform as well as those more recently derived. This indicates that wind shield type (or lack thereof) is more important in determining the magnitude of wind-induced undercatch than the type of weighing precipitation gauge. It also demonstrates the potential for widespread use of the previously developed transfer functions. Another overarching result was that, in general, the more effective shields, which were associated with smaller unadjusted errors, also produced more accurate measurements after adjustment. This indicates that although transfer functions can effectively reduce measurement biases, effective wind shielding is still required for the most accurate measurement of solid precipitation.

Distinct Transfer Effects of Training Different Facets of Working Memory Capacity

ERIC Educational Resources Information Center

von Bastian, Claudia C.; Oberauer, Klaus

2013-01-01

The impact of working memory training on a broad set of transfer tasks was examined. Each of three groups of participants trained one specific functional category of working memory capacity: storage and processing, relational integration, and supervision. A battery comprising tests to measure working memory, task shifting, inhibition, and…

Microassembly of Heterogeneous Materials using Transfer Printing and Thermal Processing

PubMed Central

Keum, Hohyun; Yang, Zining; Han, Kewen; Handler, Drew E.; Nguyen, Thong Nhu; Schutt-Aine, Jose; Bahl, Gaurav; Kim, Seok

2016-01-01

Enabling unique architectures and functionalities of microsystems for numerous applications in electronics, photonics and other areas often requires microassembly of separately prepared heterogeneous materials instead of monolithic microfabrication. However, microassembly of dissimilar materials while ensuring high structural integrity has been challenging in the context of deterministic transferring and joining of materials at the microscale where surface adhesion is far more dominant than body weight. Here we present an approach to assembling microsystems with microscale building blocks of four disparate classes of device-grade materials including semiconductors, metals, dielectrics, and polymers. This approach uniquely utilizes reversible adhesion-based transfer printing for material transferring and thermal processing for material joining at the microscale. The interfacial joining characteristics between materials assembled by this approach are systematically investigated upon different joining mechanisms using blister tests. The device level capabilities of this approach are further demonstrated through assembling and testing of a microtoroid resonator and a radio frequency (RF) microelectromechanical systems (MEMS) switch that involve optical and electrical functionalities with mechanical motion. This work opens up a unique route towards 3D heterogeneous material integration to fabricate microsystems. PMID:27427243

How Spreadsheets Boost Productivity.

ERIC Educational Resources Information Center

Ross, James

1988-01-01

Explains the use of computerized bookkeeping systems called spreadsheets to perform mathematical and accounting functions such as totaling expenditures, averaging test grades, and transferring funds. Advises about adapting spreadsheet programs and discusses several essential features, including linkage, macro functions, and sharing capabilities.…

Full-Scale Turbofan-Engine Turbine-Transfer Function Determination Using Three Internal Sensors

NASA Technical Reports Server (NTRS)

Hultgren, Lennart S.

2012-01-01

Noise-source separation techniques, using three engine-internal sensors, are applied to existing static-engine test data to determine the turbine transfer function for the currently subdominant combustion noise. The results are used to assess the combustion-noise prediction capability of the Aircraft Noise Prediction Program (ANOPP) and an improvement to the combustion-noise module GECOR is suggested. The work was carried out in response to the NASA Fundamental Aeronautics Subsonic Fixed Wing Program s Reduced-Perceived-Noise Technical Challenge.

Implementation and Validation of the Viscoelastic Continuum Damage Theory for Asphalt Mixture and Pavement Analysis in Brazil

NASA Astrophysics Data System (ADS)

Nascimento, Luis Alberto Herrmann do

This dissertation presents the implementation and validation of the viscoelastic continuum damage (VECD) model for asphalt mixture and pavement analysis in Brazil. It proposes a simulated damage-to-fatigue cracked area transfer function for the layered viscoelastic continuum damage (LVECD) program framework and defines the model framework's fatigue cracking prediction error for asphalt pavement reliability-based design solutions in Brazil. The research is divided into three main steps: (i) implementation of the simplified viscoelastic continuum damage (S-VECD) model in Brazil (Petrobras) for asphalt mixture characterization, (ii) validation of the LVECD model approach for pavement analysis based on field performance observations, and defining a local simulated damage-to-cracked area transfer function for the Fundao Project's pavement test sections in Rio de Janeiro, RJ, and (iii) validation of the Fundao project local transfer function to be used throughout Brazil for asphalt pavement fatigue cracking predictions, based on field performance observations of the National MEPDG Project's pavement test sections, thereby validating the proposed framework's prediction capability. For the first step, the S-VECD test protocol, which uses controlled-on-specimen strain mode-of-loading, was successfully implemented at the Petrobras and used to characterize Brazilian asphalt mixtures that are composed of a wide range of asphalt binders. This research verified that the S-VECD model coupled with the GR failure criterion is accurate for fatigue life predictions of Brazilian asphalt mixtures, even when very different asphalt binders are used. Also, the applicability of the load amplitude sweep (LAS) test for the fatigue characterization of the asphalt binders was checked, and the effects of different asphalt binders on the fatigue damage properties of the asphalt mixtures was investigated. The LAS test results, modeled according to VECD theory, presented a strong correlation with the asphalt mixtures' fatigue performance. In the second step, the S-VECD test protocol was used to characterize the asphalt mixtures used in the 27 selected Fundao project test sections and subjected to real traffic loading. Thus, the asphalt mixture properties, pavement structure data, traffic loading, and climate were input into the LVECD program for pavement fatigue cracking performance simulations. The simulation results showed good agreement with the field-observed distresses. Then, a damage shift approach, based on the initial simulated damage growth rate, was introduced in order to obtain a unique relationship between the LVECD-simulated shifted damage and the pavement-observed fatigue cracked areas. This correlation was fitted to a power form function and defined as the averaged reduced damage-to-cracked area transfer function. The last step consisted of using the averaged reduced damage-to-cracked area transfer function that was developed in the Fundao project to predict pavement fatigue cracking in 17 National MEPDG project test sections. The procedures for the material characterization and pavement data gathering adopted in this step are similar to those used for the Fundao project simulations. This research verified that the transfer function defined for the Fundao project sections can be used for the fatigue performance predictions of a wide range of pavements all over Brazil, as the predicted and observed cracked areas for the National MEPDG pavements presented good agreement, following the same trends found for the Fundao project pavement sites. Based on the prediction errors determined for all 44 pavement test sections (Fundao and National MEPDG test sections), the proposed framework's prediction capability was determined so that reliability-based solutions can be applied for flexible pavement design. It was concluded that the proposed LVECD program framework has very good fatigue cracking prediction capability.

A Wireless Interface for Replacing the Cables in Bridge-Sensor Applications

PubMed Central

Pavlin, Marko; Novak, Franc

2012-01-01

This paper presents a solution in which a wireless interface is employed to replace the cables in bridge-sensor measurement applications. The most noticeable feature of the presented approach is the fact that the wireless interface simply replaces the cables without any additional hardware modification to the existing system. In this approach, the concept of reciprocal topology is employed, where the transmitter side acquires signals with its own transfer function and the receiver side reconstructs them with the transfer function reciprocal to the transmitter transfer function. In this paper the principle of data acquisition and reconstruction is described together with the implementation details of the signal transfer from the sensor to the signal-monitoring equipment. The wireless data communication was investigated and proprietary data-reduction methods were developed. The proposed methods and algorithms were implemented using two different wireless technologies. The performance was evaluated with a dedicated data-acquisition system and finally, the test results were analyzed. The two different sets of results indicated the high level of amplitude and the temporal accuracy of the wirelessly transferred sensor signals. PMID:23112585

Putting brain training to the test.

PubMed

Owen, Adrian M; Hampshire, Adam; Grahn, Jessica A; Stenton, Robert; Dajani, Said; Burns, Alistair S; Howard, Robert J; Ballard, Clive G

2010-06-10

'Brain training', or the goal of improved cognitive function through the regular use of computerized tests, is a multimillion-pound industry, yet in our view scientific evidence to support its efficacy is lacking. Modest effects have been reported in some studies of older individuals and preschool children, and video-game players outperform non-players on some tests of visual attention. However, the widely held belief that commercially available computerized brain-training programs improve general cognitive function in the wider population in our opinion lacks empirical support. The central question is not whether performance on cognitive tests can be improved by training, but rather, whether those benefits transfer to other untrained tasks or lead to any general improvement in the level of cognitive functioning. Here we report the results of a six-week online study in which 11,430 participants trained several times each week on cognitive tasks designed to improve reasoning, memory, planning, visuospatial skills and attention. Although improvements were observed in every one of the cognitive tasks that were trained, no evidence was found for transfer effects to untrained tasks, even when those tasks were cognitively closely related.

Improvements in hip flexibility do not transfer to mobility in functional movement patterns.

PubMed

Moreside, Janice M; McGill, Stuart M

2013-10-01

The purpose of this study was to analyze the transference of increased passive hip range of motion (ROM) and core endurance to functional movement. Twenty-four healthy young men with limited hip mobility were randomly assigned to 4 intervention groups: group 1, stretching; group 2, stretching plus hip/spine disassociation exercises; group 3, core endurance; and group 4, control. Previous work has documented the large increase in passive ROM and core endurance that was attained over the 6-week interventions, but whether these changes transferred to functional activities was unclear. Four dynamic activities were analyzed before and after the 6-week interventions: active standing hip extension, lunge, a standing twist/reach maneuver, and exercising on an elliptical trainer. A Vicon motion capture system collected body segment kinematics, with hip and lumbar spine angles subsequently calculated in Visual 3D. Repeated measures analyses of variance determined group effects on various hip and spine angles, with paired t-tests on specific pre/post pairs. Despite the large increases in passive hip ROM, there was no evidence of increased hip ROM used during functional movement testing. Similarly, the only significant change in lumbar motion was a reduction in lumbar rotation during the active hip extension maneuver (p < 0.05). These results indicate that changes in passive ROM or core endurance do not automatically transfer to changes in functional movement patterns. This implies that training and rehabilitation programs may benefit from an additional focus on 'grooving' new motor patterns if newfound movement range is to be used.

Variationally consistent approximation scheme for charge transfer

NASA Technical Reports Server (NTRS)

Halpern, A. M.

1978-01-01

The author has developed a technique for testing various charge-transfer approximation schemes for consistency with the requirements of the Kohn variational principle for the amplitude to guarantee that the amplitude is correct to second order in the scattering wave functions. Applied to Born-type approximations for charge transfer it allows the selection of particular groups of first-, second-, and higher-Born-type terms that obey the consistency requirement, and hence yield more reliable approximation to the amplitude.

Fluid Mechanics and Heat Transfer Spirally Fluted Tubing,

DTIC Science & Technology

1981-08-01

Condensation of Helically Fluted Tubes in a Vertical Configuration 7 2. EXPERIMENTAL PROGRAM 2.1 Water Flow Facility 13 2.2 Test Section Construction...transfer on the outside of the tube is achieved. In a vertical orientation with fluid condensing on the outside of the helically fluted tube, the...transfer performance on the inside of helically fluted tubes as indicated by the Nusselt modulus, Nu/Pr0 .4 . as a function of the Reynolds number is

Training Data Requirement for a Neural Network to Predict Aerodynamic Coefficients

NASA Technical Reports Server (NTRS)

Korsmeyer, David (Technical Monitor); Rajkumar, T.; Bardina, Jorge

2003-01-01

Basic aerodynamic coefficients are modeled as functions of angle of attack, speed brake deflection angle, Mach number, and side slip angle. Most of the aerodynamic parameters can be well-fitted using polynomial functions. We previously demonstrated that a neural network is a fast, reliable way of predicting aerodynamic coefficients. We encountered few under fitted and/or over fitted results during prediction. The training data for the neural network are derived from wind tunnel test measurements and numerical simulations. The basic questions that arise are: how many training data points are required to produce an efficient neural network prediction, and which type of transfer functions should be used between the input-hidden layer and hidden-output layer. In this paper, a comparative study of the efficiency of neural network prediction based on different transfer functions and training dataset sizes is presented. The results of the neural network prediction reflect the sensitivity of the architecture, transfer functions, and training dataset size.

Implementation and extension of the impulse transfer function method for future application to the space shuttle project. Volume 1: Analysis and correlation studies

NASA Technical Reports Server (NTRS)

Mantus, M.; Pardo, H.

1973-01-01

Computer programming, data processing, and a correlation study that employed data collected in the first phase test were used to demonstrate that standard test procedures and equipment could be used to collect a significant number of transfer functions from tests of the Lunar Module test article LTA-11. The testing consisted of suspending the vehicle from the apex fittings of the outrigger trusses through a set of air springs to simulate the free-free state. Impulsive loadings were delivered, one at a time, at each of the landing gear's attachment points, in three mutually perpendicular directions; thus a total of 36 impulses were applied to the vehicle. Time histories of each pulse were recorded on magnetic tape along with 40 channels of strain gage response and 28 channels of accelerometer response. Since an automated data processing system was not available, oscillograph playbacks were made of all 2400 time histories as a check on the validity of the data taken. In addition, one channel of instrumentation was processed to determine its response to a set of forcing functions from a prior LTA-11 drop test. This prediction was compared with drop test results as a first measure of accuracy.

Development of rotorcraft interior noise control concepts. Phase 2: Full scale testing, revision 1

NASA Technical Reports Server (NTRS)

Yoerkie, C. A.; Gintoli, P. J.; Moore, J. A.

1986-01-01

The phase 2 effort consisted of a series of ground and flight test measurements to obtain data for validation of the Statistical Energy Analysis (SEA) model. Included in the gound tests were various transfer function measurements between vibratory and acoustic subsystems, vibration and acoustic decay rate measurements, and coherent source measurements. The bulk of these, the vibration transfer functions, were used for SEA model validation, while the others provided information for characterization of damping and reverberation time of the subsystems. The flight test program included measurements of cabin and cockpit sound pressure level, frame and panel vibration level, and vibration levels at the main transmission attachment locations. Comparisons between measured and predicted subsystem excitation levels from both ground and flight testing were evaluated. The ground test data show good correlation with predictions of vibration levels throughout the cabin overhead for all excitations. The flight test results also indicate excellent correlation of inflight sound pressure measurements to sound pressure levels predicted by the SEA model, where the average aircraft speech interference level is predicted within 0.2 dB.

Heat-transfer processes in air-cooled engine cylinders

NASA Technical Reports Server (NTRS)

Pinkel, Benjamin

1938-01-01

From a consideration of heat-transfer theory, semi-empirical expressions are set up for the transfer of heat from the combustion gases to the cylinder of an air-cooled engine and from the cylinder to the cooling air. Simple equations for the average head and barrel temperatures as functions of the important engine and cooling variables are obtained from these expressions. The expressions involve a few empirical constants, which may be readily determined from engine tests. Numerical values for these constants were obtained from single-cylinder engine tests for cylinders of the Pratt & Whitney 1535 and 1340-h engines. The equations provide a means of calculating the effect of the various engine and cooling variables on the cylinder temperatures and also of correlating the results of engine cooling tests. An example is given of the application of the equations to the correlation of cooling-test data obtained in flight.

Analysis of electromagnetic forces and causality in electron microscopy.

PubMed

Reyes-Coronado, Alejandro; Ortíz-Solano, Carlos Gael; Zabala, Nerea; Rivacoba, Alberto; Esquivel-Sirvent, Raúl

2018-09-01

The non-physical effects on the transverse momentum transfer from fast electrons to gold nanoparticles associated to the use of non-causal dielectric functions are studied. A direct test of the causality based on the surface Kramers-Kronig relations is presented. This test is applied to the different dielectric function used to describe gold nanostructures in electron microscopy. Copyright © 2018. Published by Elsevier B.V.

Development and testing of transfer functions for generating quantitative climatic estimates from Australian pollen data

NASA Astrophysics Data System (ADS)

Cook, Ellyn J.; van der Kaars, Sander

2006-10-01

We review attempts to derive quantitative climatic estimates from Australian pollen data, including the climatic envelope, climatic indicator and modern analogue approaches, and outline the need to pursue alternatives for use as input to, or validation of, simulations by models of past, present and future climate patterns. To this end, we have constructed and tested modern pollen-climate transfer functions for mainland southeastern Australia and Tasmania using the existing southeastern Australian pollen database and for northern Australia using a new pollen database we are developing. After testing for statistical significance, 11 parameters were selected for mainland southeastern Australia, seven for Tasmania and six for northern Australia. The functions are based on weighted-averaging partial least squares regression and their predictive ability evaluated against modern observational climate data using leave-one-out cross-validation. Functions for summer, annual and winter rainfall and temperatures are most robust for southeastern Australia, while in Tasmania functions for minimum temperature of the coldest period, mean winter and mean annual temperature are the most reliable. In northern Australia, annual and summer rainfall and annual and summer moisture indexes are the strongest. The validation of all functions means all can be applied to Quaternary pollen records from these three areas with confidence. Copyright

Generation of Leishmania Hybrids by Whole Genomic DNA Transformation

PubMed Central

Coelho, Adriano C.; Leprohon, Philippe; Ouellette, Marc

2012-01-01

Genetic exchange is a powerful tool to study gene function in microorganisms. Here, we tested the feasibility of generating Leishmania hybrids by electroporating genomic DNA of donor cells into recipient Leishmania parasites. The donor DNA was marked with a drug resistance marker facilitating the selection of DNA transfer into the recipient cells. The transferred DNA was integrated exclusively at homologous locus and was as large as 45 kb. The independent generation of L. infantum hybrids with L. major sequences was possible for several chromosomal regions. Interfering with the mismatch repair machinery by inactivating the MSH2 gene enabled an increased efficiency of recombination between divergent sequences, hence favouring the selection of hybrids between species. Hybrids were shown to acquire the phenotype derived from the donor cells, as demonstrated for the transfer of drug resistance genes from L. major into L. infantum. The described method is a first step allowing the generation of in vitro hybrids for testing gene functions in a natural genomic context in the parasite Leishmania. PMID:23029579

The transfer function method for gear system dynamics applied to conventional and minimum excitation gearing designs

NASA Technical Reports Server (NTRS)

Mark, W. D.

1982-01-01

A transfer function method for predicting the dynamic responses of gear systems with more than one gear mesh is developed and applied to the NASA Lewis four-square gear fatigue test apparatus. Methods for computing bearing-support force spectra and temporal histories of the total force transmitted by a gear mesh, the force transmitted by a single pair of teeth, and the maximum root stress in a single tooth are developed. Dynamic effects arising from other gear meshes in the system are included. A profile modification design method to minimize the vibration excitation arising from a pair of meshing gears is reviewed and extended. Families of tooth loading functions required for such designs are developed and examined for potential excitation of individual tooth vibrations. The profile modification design method is applied to a pair of test gears.

The transfer of Cfunc contextual control through equivalence relations.

PubMed

Perez, William F; Fidalgo, Adriana P; Kovac, Roberta; Nico, Yara C

2015-05-01

Derived relational responding is affected by contextual stimuli (Cfunc) that select specific stimulus functions. The present study investigated the transfer of Cfunc contextual control through equivalence relations by evaluating both (a) the maintenance of Cfunc contextual control after the expansion of a relational network, and (b) the establishment of novel contextual stimuli by the transfer of Cfunc contextual control through equivalence relations. Initially, equivalence relations were established and contingencies were arranged so that colors functioned as Cfunc stimuli controlling participants' key-pressing responses in the presence of any stimulus from a three-member equivalence network. To investigate the first research question, the three-member equivalence relations were expanded to five members and the novel members were presented with the Cfunc stimuli in the key-pressing task. To address the second goal of this study, the colors (Cfunc) were established as equivalent to certain line patterns. The transfer of contextual cue function (Cfunc) was tested replacing the colored backgrounds with line patterns in the key-pressing task. Results suggest that the Cfunc contextual control was transferred to novel stimuli that were added to the relational network. In addition, the line patterns indirectly acquired the contextual cue function (Cfunc) initially established for the colored backgrounds. The conceptual and applied implications of Cfunc contextual control are discussed. © Society for the Experimental Analysis of Behavior.

Horizontal gene transfer of microbial cellulases into nematode genomes is associated with functional assimilation and gene turnover

PubMed Central

2011-01-01

Background Natural acquisition of novel genes from other organisms by horizontal or lateral gene transfer is well established for microorganisms. There is now growing evidence that horizontal gene transfer also plays important roles in the evolution of eukaryotes. Genome-sequencing and EST projects of plant and animal associated nematodes such as Brugia, Meloidogyne, Bursaphelenchus and Pristionchus indicate horizontal gene transfer as a key adaptation towards parasitism and pathogenicity. However, little is known about the functional activity and evolutionary longevity of genes acquired by horizontal gene transfer and the mechanisms favoring such processes. Results We examine the transfer of cellulase genes to the free-living and beetle-associated nematode Pristionchus pacificus, for which detailed phylogenetic knowledge is available, to address predictions by evolutionary theory for successful gene transfer. We used transcriptomics in seven Pristionchus species and three other related diplogastrid nematodes with a well-defined phylogenetic framework to study the evolution of ancestral cellulase genes acquired by horizontal gene transfer. We performed intra-species, inter-species and inter-genic analysis by comparing the transcriptomes of these ten species and tested for cellulase activity in each species. Species with cellulase genes in their transcriptome always exhibited cellulase activity indicating functional integration into the host's genome and biology. The phylogenetic profile of cellulase genes was congruent with the species phylogeny demonstrating gene longevity. Cellulase genes show notable turnover with elevated birth and death rates. Comparison by sequencing of three selected cellulase genes in 24 natural isolates of Pristionchus pacificus suggests these high evolutionary dynamics to be associated with copy number variations and positive selection. Conclusion We could demonstrate functional integration of acquired cellulase genes into the nematode's biology as predicted by theory. Thus, functional assimilation, remarkable gene turnover and selection might represent key features of horizontal gene transfer events in nematodes. PMID:21232122

Horizontal gene transfer of microbial cellulases into nematode genomes is associated with functional assimilation and gene turnover.

PubMed

Mayer, Werner E; Schuster, Lisa N; Bartelmes, Gabi; Dieterich, Christoph; Sommer, Ralf J

2011-01-13

Natural acquisition of novel genes from other organisms by horizontal or lateral gene transfer is well established for microorganisms. There is now growing evidence that horizontal gene transfer also plays important roles in the evolution of eukaryotes. Genome-sequencing and EST projects of plant and animal associated nematodes such as Brugia, Meloidogyne, Bursaphelenchus and Pristionchus indicate horizontal gene transfer as a key adaptation towards parasitism and pathogenicity. However, little is known about the functional activity and evolutionary longevity of genes acquired by horizontal gene transfer and the mechanisms favoring such processes. We examine the transfer of cellulase genes to the free-living and beetle-associated nematode Pristionchus pacificus, for which detailed phylogenetic knowledge is available, to address predictions by evolutionary theory for successful gene transfer. We used transcriptomics in seven Pristionchus species and three other related diplogastrid nematodes with a well-defined phylogenetic framework to study the evolution of ancestral cellulase genes acquired by horizontal gene transfer. We performed intra-species, inter-species and inter-genic analysis by comparing the transcriptomes of these ten species and tested for cellulase activity in each species. Species with cellulase genes in their transcriptome always exhibited cellulase activity indicating functional integration into the host's genome and biology. The phylogenetic profile of cellulase genes was congruent with the species phylogeny demonstrating gene longevity. Cellulase genes show notable turnover with elevated birth and death rates. Comparison by sequencing of three selected cellulase genes in 24 natural isolates of Pristionchus pacificus suggests these high evolutionary dynamics to be associated with copy number variations and positive selection. We could demonstrate functional integration of acquired cellulase genes into the nematode's biology as predicted by theory. Thus, functional assimilation, remarkable gene turnover and selection might represent key features of horizontal gene transfer events in nematodes.

No Evidence for True Training and Transfer Effects after Inhibitory Control Training in Young Healthy Adults

ERIC Educational Resources Information Center

Enge, Sören; Behnke, Alexander; Fleischhauer, Monika; Küttler, Lena; Kliegel, Matthias; Strobel, Alexander

2014-01-01

Recent studies reported that training of working memory may improve performance in the trained function and beyond. Other executive functions, however, have been rarely or not yet systematically examined. The aim of this study was to test the effectiveness of inhibitory control (IC) training to produce true training-related function improvements…

Testing complex animal cognition: Concept learning, proactive interference, and list memory.

PubMed

Wright, Anthony A

2018-01-01

This article describes an approach for assessing and comparing complex cognition in rhesus monkeys and pigeons by training them in a sequence of synergistic tasks, each yielding a whole function for enhanced comparisons. These species were trained in similar same/different tasks with expanding training sets (8, 16, 32, 64, 128 … 1024 pictures) followed by novel-stimulus transfer eventually resulting in full abstract-concept learning. Concept-learning functions revealed better rhesus transfer throughout and full concept learning at the 128 set, versus pigeons at the 256 set. They were then tested in delayed same/different tasks for proactive interference by inserting occasional tests within trial-unique sessions where the test stimulus matched a previous sample stimulus (1, 2, 4, 8, 16 trials prior). Proactive-interference functions revealed time-based interference for pigeons (1, 10 s delays), but event-based interference for rhesus (no effect of 1, 10, 20 s delays). They were then tested in list-memory tasks by expanding the sample to four samples in trial-unique sessions (minimizing proactive interference). The four-item, list-memory functions revealed strong recency memory at short delays, gradually changing to strong primacy memory at long delays over 30 s for rhesus, and 10 s for pigeons. Other species comparisons and future directions are discussed. © 2018 Society for the Experimental Analysis of Behavior.

Hybrid fusions show that inter-monomer electron transfer robustly supports cytochrome bc{sub 1} function in vivo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ekiert, Robert; Czapla, Monika; Sarewicz, Marcin

2014-08-22

Highlights: • We used hybrid fusion bc{sub 1} complex to test inter-monomer electron transfer in vivo. • Cross-inactivated complexes were able to sustain photoheterotrophic growth. • Inter-monomer electron transfer supports catalytic cycle in vivo. • bc{sub 1} dimer is functional even when cytochrome b subunits come from different species. - Abstract: Electronic connection between Q{sub o} and Q{sub i} quinone catalytic sites of dimeric cytochrome bc{sub 1} is a central feature of the energy-conserving Q cycle. While both the intra- and inter-monomer electron transfers were shown to connect the sites in the enzyme, mechanistic and physiological significance of the lattermore » remains unclear. Here, using a series of mutated hybrid cytochrome bc{sub 1}-like complexes, we show that inter-monomer electron transfer robustly sustains the function of the enzyme in vivo, even when the two subunits in a dimer come from different species. This indicates that minimal requirement for bioenergetic efficiency is to provide a chain of cofactors for uncompromised electron flux between the catalytic sites, while the details of protein scaffold are secondary.« less

How Well Can Modern Density Functionals Predict Internuclear Distances at Transition States?

PubMed

Xu, Xuefei; Alecu, I M; Truhlar, Donald G

2011-06-14

We introduce a new database called TSG48 containing 48 transition state geometrical data (in particular, internuclear distances in transition state structures) for 16 main group reactions. The 16 reactions are the 12 reactions in the previously published DBH24 database (which includes hydrogen transfer reactions, heavy-atom transfer reactions, nucleophilic substitution reactions, and association reactions plus one unimolecular isomerization) plus four H-transfer reactions in which a hydrogen atom is abstracted by the methyl or hydroperoxyl radical from the two different positions in methanol. The data in TSG48 include data for four reactions that have previously been treated at a very high level in the literature. These data are used to test and validate methods that are affordable for the entire test suite, and the most accurate of these methods is found to be the multilevel BMC-CCSD method. The data that constitute the TSG48 database are therefore taken to consist of these very high level calculations for the four reactions where they are available and BMC-CCSD calculations for the other 12 reactions. The TSG48 database is used to assess the performance of the eight Minnesota density functionals from the M05-M08 families and 26 other high-performance and popular density functionals for locating transition state geometries. For comparison, the MP2 and QCISD wave function methods have also been tested for transition state geometries. The MC3BB and MC3MPW doubly hybrid functionals and the M08-HX and M06-2X hybrid meta-GGAs are found to have the best performance of all of the density functionals tested. M08-HX is the most highly recommended functional due to the excellent performance for all five subsets of TSG48, as well as having a lower cost when compared to doubly hybrid functionals. The mean absolute errors in transition state internuclear distances associated with breaking and forming bonds as calculated by the B2PLYP, MP2, and B3LYP methods are respectively about 2, 3, and 5 times larger than those calculated by MC3BB and M08-HX.

Evaluating lotion transfer from products to skin using the behind-the-knee test.

PubMed

Farage, Miranda A

2010-05-01

Adding lotions or emollients to the surface of a variety of paper products confers a number of benefits to the skin of consumers. A modification of the 'behind-the-knee (BTK)' test model was used as a means of measuring the effectiveness of lotion transfer to the skin. Two series of feminine protection pads were prepared: (1) identically constructed pads differing only in the amount of lotion applied to the surface and (2) pads of various compositions to compare the influence of other product characteristics. For the first series, pads were applied for 3 h using the BTK protocol, and lotion transfer was evaluated. For the second series of products, two sample pads were applied consecutively for 3 h each, and lotion transfer was evaluated a both time points (e.g., 3 and 6 h). In addition, a clinical in-use study was used to evaluate lotion transfer for the second product series. In the BTK model using pads of identical composition, lotion transfer was a function of the amount of lotion placed on the pad. However, results from the second product series indicated that when pads were prepared using different absorbant materials (supreabsorbent gelling material, or AGM and cellulose), pads with the AGM core transferred lotion more effectively than pads with a cellulose core. Other product characteristics, i.e., pad thickness and lotion configuration, did not detectibly influence lotion transfer. The results of an in-use clinical study conducted on the second series of test products were directionally similar to those from the BTK, but statistical significance was not reached. An adaptation of the BTK test method provides an effective means of evaluating the transfer of lotion formulations from feminine protection pads at a fraction of the cost of clinical in-use studies.

Spectrally-Invariant Approximation Within Atmospheric Radiative Transfer

NASA Technical Reports Server (NTRS)

Marshak, A.; Knyazikhin, Y.; Chiu, J. C.; Wiscombe, W. J.

2011-01-01

Certain algebraic combinations of single scattering albedo and solar radiation reflected from, or transmitted through, vegetation canopies do not vary with wavelength. These "spectrally invariant relationships" are the consequence of wavelength independence of the extinction coefficient and scattering phase function in vegetation. In general, this wavelength independence does not hold in the atmosphere, but in clouddominated atmospheres the total extinction and total scattering phase function vary only weakly with wavelength. This paper identifies the atmospheric conditions under which the spectrally invariant approximation can accurately describe the extinction. and scattering properties of cloudy atmospheres. The validity of the assumptions and the accuracy of the approximation are tested with ID radiative transfer calculations using publicly available radiative transfer models: Discrete Ordinate Radiative Transfer (DISORT) and Santa Barbara DISORT Atmospheric Radiative Transfer (SBDART). It is shown for cloudy atmospheres with cloud optical depth above 3, and for spectral intervals that exclude strong water vapor absorption, that the spectrally invariant relationships found in vegetation canopy radiative transfer are valid to better than 5%. The physics behind this phenomenon, its mathematical basis, and possible applications to remote sensing and climate are discussed.

H2-norm for mesh optimization with application to electro-thermal modeling of an electric wire in automotive context

NASA Astrophysics Data System (ADS)

Chevrié, Mathieu; Farges, Christophe; Sabatier, Jocelyn; Guillemard, Franck; Pradere, Laetitia

2017-04-01

In automotive application field, reducing electric conductors dimensions is significant to decrease the embedded mass and the manufacturing costs. It is thus essential to develop tools to optimize the wire diameter according to thermal constraints and protection algorithms to maintain a high level of safety. In order to develop such tools and algorithms, accurate electro-thermal models of electric wires are required. However, thermal equation solutions lead to implicit fractional transfer functions involving an exponential that cannot be embedded in a car calculator. This paper thus proposes an integer order transfer function approximation methodology based on a spatial discretization for this class of fractional transfer functions. Moreover, the H2-norm is used to minimize approximation error. Accuracy of the proposed approach is confirmed with measured data on a 1.5 mm2 wire implemented in a dedicated test bench.

Surfactant effects on alpha-factors in aeration systems.

PubMed

Rosso, Diego; Stenstrom, Michael K

2006-04-01

Aeration in wastewater treatment processes accounts for the largest fraction of plant energy costs. Aeration systems function by shearing the surface (surface aerators) or releasing bubbles at the bottom of the tank (coarse- or fine-bubble aerators). Surfactant accumulation on gas-liquid interfaces reduces mass transfer rates, and this reduction in general is larger for fine-bubble aerators. This study evaluates mass transfer effects on the characterization and specification of aeration systems in clean and process water conditions. Tests at different interfacial turbulence regimes show higher gas transfer depression for lower turbulence regimes. Contamination effects can be offset at the expense of operating efficiency, which is characteristic of surface aerators and coarse-bubble diffusers. Results describe the variability of alpha-factors measured at small scale, due to uncontrolled energy density. Results are also reported in dimensionless empirical correlations describing mass transfer as a function of physiochemical and geometrical characteristics of the aeration process.

The effects of video-game training on broad cognitive transfer in multiple sclerosis: A pilot randomized controlled trial.

PubMed

Janssen, Alisha; Boster, Aaron; Lee, HyunKyu; Patterson, Beth; Prakash, Ruchika Shaurya

2015-01-01

Multiple sclerosis (MS) is a neurodegenerative disease of the central nervous system that results in diffuse nerve damage and associated physical and cognitive impairments. Of the few comprehensive rehabilitation options that exist for populations with lower baseline cognitive functioning, those that have been successful at eliciting broad cognitive improvements have focused on a multimodal training approach, emphasizing complex cognitive processing that utilizes multiple domains simultaneously. The current study sought to determine the feasibility of an 8-week, hybrid-variable priority training (HVT) program, with a secondary aim to assess the success of this training paradigm at eliciting broad cognitive transfer effects. Capitalizing on the multimodal training modalities offered by the Space Fortress platform, we compared the HVT strategy-based intervention with a waitlist control group, to primarily assess skill acquisition and secondarily determine presence of cognitive transfer. Twenty-eight participants met inclusionary criteria for the study and were randomized to either training or waitlist control groups. To assess broad transfer effects, a battery of neuropsychological tests was administered pre- and post-intervention. The results indicated an overall improvement in skill acquisition and evidence for the feasibility of the intervention, but a lack of broad transfer to tasks of cognitive functioning. Participants in the training group, however, did show improvements on a measure of spatial short-term memory. The current investigation provided support for the feasibility of a multimodal training approach, using the HVT strategy, within the MS population, but lacked broad transfer to multiple domains of cognitive functioning. Future improvements to obtain greater cognitive transfer efficacy would include a larger sample size, a longer course of training to evoke greater game score improvement, the inclusion of only cognitively impaired individuals, and integration of subjective measures of improvement in addition to objective tests of cognitive performance.

A study of the flow boiling heat transfer in an annular heat exchanger with a mini gap

NASA Astrophysics Data System (ADS)

Musiał, Tomasz; Piasecka, Magdalena; Hożejowska, Sylwia

In this paper the research on flow boiling heat transfer in an annular mini gap was discussed. A one- dimensional mathematical approach was proposed to describe stationary heat transfer in the gap. The mini gap 1 mm wide was created between a metal pipe with enhanced exterior surface and an external tempered glass pipe positioned along the same axis. The experimental test stand consists of several systems: the test loop in which distilled water circulates, the data and image acquisition system and the supply and control system. Known temperature distributions of the metal pipe with enhanced surface and of the working fluid helped to determine, from the Robin boundary condition, the local heat transfer coefficients at the fluid - heated surface contact. In the proposed mathematical model it is assumed that the cylindrical wall is a planar multilayer wall. The numerical results are presented on a chart as function of the heat transfer coefficient along the length of the mini gap.

Neural correlates of training and transfer effects in working memory in older adults.

PubMed

Heinzel, Stephan; Lorenz, Robert C; Pelz, Patricia; Heinz, Andreas; Walter, Henrik; Kathmann, Norbert; Rapp, Michael A; Stelzel, Christine

2016-07-01

As indicated by previous research, aging is associated with a decline in working memory (WM) functioning, related to alterations in fronto-parietal neural activations. At the same time, previous studies showed that WM training in older adults may improve the performance in the trained task (training effect), and more importantly, also in untrained WM tasks (transfer effects). However, neural correlates of these transfer effects that would improve understanding of its underlying mechanisms, have not been shown in older participants as yet. In this study, we investigated blood-oxygen-level-dependent (BOLD) signal changes during n-back performance and an untrained delayed recognition (Sternberg) task following 12sessions (45min each) of adaptive n-back training in older adults. The Sternberg task used in this study allowed to test for neural training effects independent of specific task affordances of the trained task and to separate maintenance from updating processes. Thirty-two healthy older participants (60-75years) were assigned either to an n-back training or a no-contact control group. Before (t1) and after (t2) training/waiting period, both the n-back task and the Sternberg task were conducted while BOLD signal was measured using functional Magnetic Resonance Imaging (fMRI) in all participants. In addition, neuropsychological tests were performed outside the scanner. WM performance improved with training and behavioral transfer to tests measuring executive functions, processing speed, and fluid intelligence was found. In the training group, BOLD signal in the right lateral middle frontal gyrus/caudal superior frontal sulcus (Brodmann area, BA 6/8) decreased in both the trained n-back and the updating condition of the untrained Sternberg task at t2, compared to the control group. fMRI findings indicate a training-related increase in processing efficiency of WM networks, potentially related to the process of WM updating. Performance gains in untrained tasks suggest that transfer to other cognitive tasks remains possible in aging. Copyright © 2016 Elsevier Inc. All rights reserved.

Valence and charge-transfer optical properties for some SinCm (m, n ≤ 12) clusters: Comparing TD-DFT, complete-basis-limit EOMCC, and benchmarks from spectroscopy

NASA Astrophysics Data System (ADS)

Lutz, Jesse J.; Duan, Xiaofeng F.; Ranasinghe, Duminda S.; Jin, Yifan; Margraf, Johannes T.; Perera, Ajith; Burggraf, Larry W.; Bartlett, Rodney J.

2018-05-01

Accurate optical characterization of the closo-Si12C12 molecule is important to guide experimental efforts toward the synthesis of nano-wires, cyclic nano-arrays, and related array structures, which are anticipated to be robust and efficient exciton materials for opto-electronic devices. Working toward calibrated methods for the description of closo-Si12C12 oligomers, various electronic structure approaches are evaluated for their ability to reproduce measured optical transitions of the SiC2, Si2Cn (n = 1-3), and Si3Cn (n = 1, 2) clusters reported earlier by Steglich and Maier [Astrophys. J. 801, 119 (2015)]. Complete-basis-limit equation-of-motion coupled-cluster (EOMCC) results are presented and a comparison is made between perturbative and renormalized non-iterative triples corrections. The effect of adding a renormalized correction for quadruples is also tested. Benchmark test sets derived from both measurement and high-level EOMCC calculations are then used to evaluate the performance of a variety of density functionals within the time-dependent density functional theory (TD-DFT) framework. The best-performing functionals are subsequently applied to predict valence TD-DFT excitation energies for the lowest-energy isomers of SinC and Sin-1C7-n (n = 4-6). TD-DFT approaches are then applied to the SinCn (n = 4-12) clusters and unique spectroscopic signatures of closo-Si12C12 are discussed. Finally, various long-range corrected density functionals, including those from the CAM-QTP family, are applied to a charge-transfer excitation in a cyclic (Si4C4)4 oligomer. Approaches for gauging the extent of charge-transfer character are also tested and EOMCC results are used to benchmark functionals and make recommendations.

Multi-hundred kilowatt roll ring assembly

NASA Technical Reports Server (NTRS)

Jacobson, Peter E.

1985-01-01

A program was completed to develop an evaluation unit of a high power rotary transfer device for potential application in a space environment. This device was configured around a Roll Ring concept which performs the same function as a slip ring/brush assembly with a rolling instead of sliding interface. An eight circuit Evaluation Unit (EU) and a portable Test Fixture (TF) were designed and fabricated. The EU was designed to transfer currents to 200 amperes at a potential of as high as 500 volts for an ultimate 100 kW/circuit transfer capability. The EU was evaluated in vacuum at dc transfer currents of 50 to 200 amperes at voltages to 10 volts and at 500 volts at 2 amperes. Power transfer to levels of 2 kW through each of the eight circuits was completed. Power transfer in vacuum at levels and efficiencies not previously achieved was demonstrated. The terminal-to-terminal resistance was measured to be greater than 0.42 milliohms which translates to an efficiency at 100 kW of 99.98 percent. The EU and TF have been delivered to the Lewis Research Center and are being prepared tor testing at increased power levels and for life testing, which will include both dc and ac power.

Environmental Test Screening Procedure

NASA Technical Reports Server (NTRS)

Zeidler, Janet

2000-01-01

This procedure describes the methods to be used for environmental stress screening (ESS) of the Lightning Mapper Sensor (LMS) lens assembly. Unless otherwise specified, the procedures shall be completed in the order listed, prior to performance of the Acceptance Test Procedure (ATP). The first unit, S/N 001, will be subjected to the Qualification Vibration Levels, while the remainder will be tested at the Operational Level. Prior to ESS, all units will undergo Pre-ESS Functional Testing that includes measuring the on-axis and plus or minus 0.95 full field Modulation Transfer Function and Back Focal Length. Next, all units will undergo ESS testing, and then Acceptance testing per PR 460.

[Carbon monoxide tests in a steady state. Uptake and transfer capacity, normal values and lower limits].

PubMed

Ramonatxo, M; Préfaut, C; Guerrero, H; Moutou, H; Bansard, X; Chardon, G

1982-01-01

The aim of this study was to establish data which would best demonstrate the variations of different tests using Carbon Monoxide as a tracer gas (total and partial functional uptake coefficient and transfer capacity) to establish mean values and lower limits of normal of these tests. Multivariate statistical analysis was used; in the first stage a connection was sought between the fractional uptake coefficient (partial and total) to other parameters, comparing subjects and data. In the second stage the comparison was refined by eliminating the least useful data, trying, despite a small loss of material, to reveal the most important connections, linear or otherwise. The fractional uptake coefficients varied according to sex, also the variation of the partial alveolar-expired fractional uptake equivalent (DuACO) was largely a function of respiratory rate and tidal volume. The alveolar-arterial partial fractional uptake equivalent (DuaCO) depended more on respiratory frequency and age. Finally the total fractional uptake coefficient (DuCO) and the transfer capacity corrected per liter of ventilation (TLCO/V) were functions of these parameters. The last stage of this work, after taking account of the statistical observations consistent with the facts of these physiological hypotheses led to a search for a better way of approaching the laws linking the collected data to the fractional uptake coefficient. The lower limits of normal were arbitrarily defined, separating those 5% of subjects deviating most strongly from the mean. As a result, the relationship between the lower limit of normal and the theoretical mean value was 90% for the partial and total fractional uptake coefficient and 70% for the transfer capacity corrected per liter of ventilation.

No evidence for true training and transfer effects after inhibitory control training in young healthy adults.

PubMed

Enge, Sören; Behnke, Alexander; Fleischhauer, Monika; Küttler, Lena; Kliegel, Matthias; Strobel, Alexander

2014-07-01

Recent studies reported that training of working memory may improve performance in the trained function and beyond. Other executive functions, however, have been rarely or not yet systematically examined. The aim of this study was to test the effectiveness of inhibitory control (IC) training to produce true training-related function improvements in a sample of 122 healthy adults using a randomized, double-blind pretest/posttest/follow-up design. Two groups performed either adaptive (training group) or nonadaptive (active control) versions of go/no-go and stop-signal tasks for 3 weeks. Training gains as well as near-transfer to an untrained Stroop task and far-transfer to psychometric fluid intelligence were explored. Although the adaptive group could substantially improve overall IC task performance after training, no differences to the active control group occurred, neither at posttest nor at follow-up testing. A large decrease in response latency from pre- to posttest (and from pretest to 4 months' follow-up testing) was found when the training group was compared to the passive control group, which, however, does not sufficiently control for possible confounds. Thus, no conclusive evidence was found that this performance increase mirrors a true increase in IC function. The fact that training improvement was mainly related to response latency may indicate that individuals were more focused on performance gains in the prepotent go trials but less on the stop trials to meet the requirements of the tasks as well as possible. The challenges for response inhibition training studies are extensively discussed. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Dynamic MTF, an innovative test bench for detector characterization

NASA Astrophysics Data System (ADS)

Emmanuel, Rossi; Raphaël, Lardière; Delmonte, Stephane

2017-11-01

PLEIADES HR are High Resolution satellites for Earth observation. Placed at 695km they reach a 0.7m spatial resolution. To allow such performances, the detectors are working in a TDI mode (Time and Delay Integration) which consists in a continuous charge transfer from one line to the consecutive one while the image is passing on the detector. The spatial resolution, one of the most important parameter to test, is characterized by the MTF (Modulation Transfer Function). Usually, detectors are tested in a staring mode. For a higher level of performances assessment, a dedicated bench has been set-up, allowing detectors' MTF characterization in the TDI mode. Accuracy and reproducibility are impressive, opening the door to new perspectives in term of HR imaging systems testing.

Measuring surgeons' treatment preferences and satisfaction with nerve reconstruction techniques for children with unique brachial plexus birth palsies.

PubMed

Shah, Amee K; Zurakowski, David; Jessel, Rebecca H; Kuo, Anne; Waters, Peter M

2006-09-15

This study surveyed microsurgeons on treatments chosen for infants with brachial plexus birth palsies who have had failure of antigravity biceps and/or triceps function due to nerve surgery or natural history. Questionnaires were sent to surgeons participating in a prospective multicenter brachial plexus birth palsy study. With a response rate of 82 percent, the sample comprised 22 surgeons with extensive experience in treating brachial plexus birth palsy. The survey gathered collective information on two unique clinical groups: (1) infants with no antigravity biceps function but intact antigravity deltoid and radial nerve function and (2) infants with no antigravity radial nerve function (wrist and digital extension, triceps) but intact antigravity biceps and deltoid function. Analysis of data and age-based trends was performed using the Fisher's exact test. With failure of biceps recovery, surgeons preferred microsurgery for children 6 to 18 months old and tendon transfers for children older than 18 months. Both procedures were preferred over observation alone (p < 0.001). With regard to microsurgery techniques, with increasing age, surgeons used nerve transfers more than resected neuroma and grafting. With tendon transfers, regional transfers were performed more than 90 percent of the time at all ages. For patients with no antigravity radial nerve function, most cases at all ages were managed by observation rather than microsurgery or tendon transfers (p < 0.001). The authors' data indicate a general consensus in treatment choices for the two cases of microsurgical failure in infants with brachial plexus birth palsies as well as in satisfaction among experienced surgeons in using these treatments.

Patterns of Transfer of Adaptation Among Body Segments

NASA Technical Reports Server (NTRS)

Seidler, R. D.; Bloomberg, J. J.; Stelmach, George E.

2000-01-01

Two experiments were conducted in order to determine the patterns of transfer of visuomotor adaptation between arm and head pointing. An altered gain of display of pointing movements was used to induce a conflict between visual and somatosensory representations. Two subject groups participated in Experiment One: group 1 adapted shoulder pointing movements, and group 2 adapted wrist pointing movements to a 0.5 gain of display. Following the adaptation regimen, subjects performed a transfer test in which the shoulder group performed wrist movements and the wrist group performed shoulder movements. The results demonstrated that both groups displayed typical adaptation curves, initially undershooting the target followed by a return to baseline performance. Transfer tests revealed that both groups had high transfer of the acquired adaptation to the other joint. Experiment Two followed a similar design except that group 1 adapted head pointing movements and group 2 adapted arm pointing movements. The arm adaptation had high transfer to head pointing while the head adaptation had very little transfer to arm pointing. These results imply that, while the arm segments may share a common target representation for goal-directed actions, individual but functionally dependent target representations may exist for the control of head and arm movements.

Using frequency-domain methods to identify XV-15 aeroelastic modes

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.; Tischler, Mark B.

1987-01-01

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed) with cross spectral and transfer function methods. Modal frequencies and damping were determined by performing curve fits to transfer function magnitude and phase data and to cross spectral magnitude data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with earlier predictions.

Environmental Testing and Thermal Analysis of the NPS Solar Cell Array Tester (NPS-SCAT) CubeSat

DTIC Science & Technology

2011-06-01

BCR Battery Charge Regulator C&DH Command and Data Handling CAD Computer Aided Design CDR Critical Design Review CFT Comprehensive Functional Test ...CPT Comprehensive Performance Test CoM Center of Mass COTS Commercial Off-the-Shelf CTB Cargo Transfer Bag EDU Engineering Design Unit EPS...and inexpensive solution. 2 C. ENVIRONMENTAL TESTING Environmental testing is an important element of the design and testing of a satellite. By

An Examination of Mediators of the Transfer of Cognitive Speed of Processing Training to Everyday Functional Performance

PubMed Central

Edwards, Jerri D.; Ruva, Christine L.; O’Brien, Jennifer L.; Haley, Christine B.; Lister, Jennifer J.

2013-01-01

The purpose of these analyses was to examine mediators of the transfer of cognitive speed of processing training to improved everyday functional performance (Edwards, Wadley, Vance, Roenker, & Ball, 2005). Cognitive speed of processing and visual attention (as measured by the Useful Field of View Test; UFOV) were examined as mediators of training transfer. Secondary data analyses were conducted from the Staying Keen in Later Life (SKILL) study, a randomized cohort study including 126 community dwelling adults 63 to 87 years of age. In the SKILL study, participants were randomized to an active control group or cognitive speed of processing training (SOPT), a non-verbal, computerized intervention involving perceptual practice of visual tasks. Prior analyses found significant effects of training as measured by the UFOV and Timed Instrumental Activities of Daily Living (TIADL) Tests. Results from the present analyses indicate that speed of processing for a divided attention task significantly mediated the effect of SOPT on everyday performance (e.g., TIADL) in a multiple mediation model accounting for 91% of the variance. These findings suggest that everyday functional improvements found from SOPT are directly attributable to improved UFOV performance, speed of processing for divided attention in particular. Targeting divided attention in cognitive interventions may be important to positively affect everyday functioning among older adults. PMID:23066808

Transfer function analysis of dynamic cerebral autoregulation in humans

NASA Technical Reports Server (NTRS)

Zhang, R.; Zuckerman, J. H.; Giller, C. A.; Levine, B. D.; Blomqvist, C. G. (Principal Investigator)

1998-01-01

To test the hypothesis that spontaneous changes in cerebral blood flow are primarily induced by changes in arterial pressure and that cerebral autoregulation is a frequency-dependent phenomenon, we measured mean arterial pressure in the finger and mean blood flow velocity in the middle cerebral artery (VMCA) during supine rest and acute hypotension induced by thigh cuff deflation in 10 healthy subjects. Transfer function gain, phase, and coherence function between changes in arterial pressure and VMCA were estimated using the Welch method. The impulse response function, calculated as the inverse Fourier transform of this transfer function, enabled the calculation of transient changes in VMCA during acute hypotension, which was compared with the directly measured change in VMCA during thigh cuff deflation. Beat-to-beat changes in VMCA occurred simultaneously with changes in arterial pressure, and the autospectrum of VMCA showed characteristics similar to arterial pressure. Transfer gain increased substantially with increasing frequency from 0.07 to 0.20 Hz in association with a gradual decrease in phase. The coherence function was > 0.5 in the frequency range of 0.07-0.30 Hz and < 0.5 at < 0.07 Hz. Furthermore, the predicted change in VMCA was similar to the measured VMCA during thigh cuff deflation. These data suggest that spontaneous changes in VMCA that occur at the frequency range of 0.07-0.30 Hz are related strongly to changes in arterial pressure and, furthermore, that short-term regulation of cerebral blood flow in response to changes in arterial pressure can be modeled by a transfer function with the quality of a high-pass filter in the frequency range of 0.07-0.30 Hz.

Relationships between the decoupled and coupled transfer functions: Theoretical studies and experimental validation

NASA Astrophysics Data System (ADS)

Wang, Zengwei; Zhu, Ping; Liu, Zhao

2018-01-01

A generalized method for predicting the decoupled transfer functions based on in-situ transfer functions is proposed. The method allows predicting the decoupled transfer functions using coupled transfer functions, without disassembling the system. Two ways to derive relationships between the decoupled and coupled transfer functions are presented. Issues related to immeasurability of coupled transfer functions are also discussed. The proposed method is validated by numerical and experimental case studies.

Advances on the Transfer of Lipids by Lipid Transfer Proteins.

PubMed

Wong, Louise H; Čopič, Alenka; Levine, Tim P

2017-07-01

Transfer of lipid across the cytoplasm is an essential process for intracellular lipid traffic. Lipid transfer proteins (LTPs) are defined by highly controlled in vitro experiments. The functional relevance of these is supported by evidence for the same reactions inside cells. Major advances in the LTP field have come from structural bioinformatics identifying new LTPs, and from the development of countercurrent models for LTPs. However, the ultimate aim is to unite in vitro and in vivo data, and this is where much progress remains to be made. Even where in vitro and in vivo experiments align, rates of transfer tend not to match. Here we set out some of the advances that might test how LTPs work. Copyright © 2017. Published by Elsevier Ltd.

High resolution optical surface metrology with the slope measuring portable optical test system

NASA Astrophysics Data System (ADS)

Maldonado, Alejandro V.

New optical designs strive to achieve extreme performance, and continually increase the complexity of prescribed optical shapes, which often require wide dynamic range and high resolution. SCOTS, or the Software Configurable Optical Test System, can measure a wide range of optical surfaces with high sensitivity using surface slope. This dissertation introduces a high resolution version of SCOTS called SPOTS, or the Slope measuring Portable Optical Test System. SPOTS improves the metrology of surface features on the order of sub-millimeter to decimeter spatial scales and nanometer to micrometer level height scales. Currently there is no optical surface metrology instrument with the same utility. SCOTS uses a computer controlled display (such as an LCD monitor) and camera to measure surface slopes over the entire surface of a mirror. SPOTS differs in that an additional lens is placed near the surface under test. A small prototype system is discussed in general, providing the support for the design of future SPOTS devices. Then the SCOTS instrument transfer function is addressed, which defines the way the system filters surface heights. Lastly, the calibration and performance of larger SPOTS device is analyzed with example measurements of the 8.4-m diameter aspheric Large Synoptic Survey Telescope's (LSST) primary mirror. In general optical systems have a transfer function, which filters data. In the case of optical imaging systems the instrument transfer function (ITF) follows the modulation transfer function (MTF), which causes a reduction of contrast as a function of increasing spatial frequency due to diffraction. In SCOTS, ITF is shown to decrease the measured height of surface features as their spatial frequency increases, and thus the SCOTS and SPOTS ITF is proportional to their camera system's MTF. Theory and simulations are supported by a SCOTS measurement of a test piece with a set of lithographically written sinusoidal surface topographies. In addition, an example of a simple inverse filtering technique is provided. The success of a small SPOTS proof of concept instrument paved the way for a new larger prototype system, which is intended to measure subaperture regions on large optical mirrors. On large optics, the prototype SPOTS is light weight and it rests on the surface being tested. One advantage of this SPOTS is stability over time in maintaining its calibration. Thus the optician can simply place SPOTS on the mirror, perform a simple alignment, collect measurement data, then pick the system up and repeat at a new location. The entire process takes approximately 5 to 10 minutes, of which 3 minutes is spent collecting data. SPOTS' simplicity of design, light weight, robustness, wide dynamic range, and high sensitivity make it a useful tool for optical shop use during the fabrication and testing process of large and small optics.

Unstable Memories Create a High-Level Representation that Enables Learning Transfer.

PubMed

Mosha, Neechi; Robertson, Edwin M

2016-01-11

A memory is unstable, making it susceptible to interference and disruption, after its acquisition [1-4]. The function or possible benefit of a memory being unstable at its acquisition is not well understood. Potentially, instability may be critical for the communication between recently acquired memories, which would allow learning in one task to be transferred to the other subsequent task [1, 5]. Learning may be transferred between any memories that are unstable, even between different types of memory. Here, we test the link between a memory being unstable and the transfer of learning to a different type of memory task. We measured how learning in one task transferred to and thus improved learning in a subsequent task. There was transfer from a motor skill to a word list task and, vice versa, from a word list to a motor skill task. What was transferred was a high-level relationship between elements, rather than knowledge of the individual elements themselves. Memory instability was correlated with subsequent transfer, suggesting that transfer was related to the instability of the memory. Using different methods, we stabilized the initial memory, preventing it from being susceptible to interference, and found that these methods consistently prevented transfer to the subsequent memory task. This suggests that the transfer of learning across diverse tasks is due to a high-level representation that can only be formed when a memory is unstable. Our work has identified an important function of memory instability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Absolute calibration technique for broadband ultrasonic transducers

NASA Technical Reports Server (NTRS)

Yost, William T. (Inventor); Cantrell, John H. (Inventor)

1994-01-01

Calibrating an ultrasonic transducer can be performed with a reduced number of calculations and testing. A wide-band pulser is connected to an ultrasonic transducer under test to generate ultrasonic waves in a liquid. A single frequency is transmitted to the electrostatic acoustic transducer (ESAT) and the voltage change produced is monitored. Then a broadband ultrasonic pulse is generated by the ultrasonic transducer and received by the ESAT. The output of the ESAT is amplified and input to a digitized oscilloscope for fast Fourier transform. The resulting plot is normalized with the monitored signal from the single frequency pulse. The plot is then corrected for characteristics of the membrane and diffraction effects. The transfer function of the final plot is determined. The transfer function gives the final sensitivity of the ultrasonic transducer as a function of frequency. The advantage of the system is the speed of calibrating the transducer by a reduced number of measurements and removal of the membrane and diffraction effects.

Development of a Simple Electron Transfer and Polarization Model and Its Application to Biological Systems.

PubMed

Diller, David J

2017-01-10

Here we present a new method for point charge calculation which we call Q ET (charges by electron transfer). The intent of this work is to develop a method that can be useful for studying charge transfer in large biological systems. It is based on the intuitive framework of the Q EQ method with the key difference being that the Q ET method tracks all pairwise electron transfers by augmenting the Q EQ pseudoenergy function with a distance dependent cost function for each electron transfer. This approach solves the key limitation of the Q EQ method which is its handling of formally charged groups. First, we parametrize the Q ET method by fitting to electrostatic potentials calculated using ab initio quantum mechanics on over 11,000 small molecules. On an external test set of over 2500 small molecules the Q ET method achieves a mean absolute error of 1.37 kcal/mol/electron when compared to the ab initio electrostatic potentials. Second, we examine the conformational dependence of the charges on over 2700 tripeptides. With the tripeptide data set, we show that the conformational effects account for approximately 0.4 kcal/mol/electron on the electrostatic potentials. Third, we test the Q ET method for its ability to reproduce the effects of polarization and electron transfer on 1000 water clusters. For the water clusters, we show that the Q ET method captures about 50% of the polarization and electron transfer effects. Finally, we examine the effects of electron transfer and polarizability on the electrostatic interaction between p38 and 94 small molecule ligands. When used in conjunction with the Generalized-Born continuum solvent model, polarization and electron transfer with the Q ET model lead to an average change of 17 kcal/mol on the calculated electrostatic component of ΔG.

Horizontal gene transfer is more frequent with increased heterotrophy and contributes to parasite adaptation.

PubMed

Yang, Zhenzhen; Zhang, Yeting; Wafula, Eric K; Honaas, Loren A; Ralph, Paula E; Jones, Sam; Clarke, Christopher R; Liu, Siming; Su, Chun; Zhang, Huiting; Altman, Naomi S; Schuster, Stephan C; Timko, Michael P; Yoder, John I; Westwood, James H; dePamphilis, Claude W

2016-10-24

Horizontal gene transfer (HGT) is the transfer of genetic material across species boundaries and has been a driving force in prokaryotic evolution. HGT involving eukaryotes appears to be much less frequent, and the functional implications of HGT in eukaryotes are poorly understood. We test the hypothesis that parasitic plants, because of their intimate feeding contacts with host plant tissues, are especially prone to horizontal gene acquisition. We sought evidence of HGTs in transcriptomes of three parasitic members of Orobanchaceae, a plant family containing species spanning the full spectrum of parasitic capabilities, plus the free-living Lindenbergia Following initial phylogenetic detection and an extensive validation procedure, 52 high-confidence horizontal transfer events were detected, often from lineages of known host plants and with an increasing number of HGT events in species with the greatest parasitic dependence. Analyses of intron sequences in putative donor and recipient lineages provide evidence for integration of genomic fragments far more often than retro-processed RNA sequences. Purifying selection predominates in functionally transferred sequences, with a small fraction of adaptively evolving sites. HGT-acquired genes are preferentially expressed in the haustorium-the organ of parasitic plants-and are strongly biased in predicted gene functions, suggesting that expression products of horizontally acquired genes are contributing to the unique adaptive feeding structure of parasitic plants.

The new diatom training set from the Polish Baltic coast and diatom-based transfer functions as a tool for understanding past changes in the southern Baltic coastal lakes

NASA Astrophysics Data System (ADS)

Lutyńska, Monika; Szpikowska, Grażyna; Woszczyk, Michał; Suchińska, Anita; Burchardt, Lubomira; Messyasz, Beata

2014-05-01

The transfer function method has been developed as a useful tool for reconstruction of the past environmental changes. It is based on the assumption that the modern species, which ecological requirements are known, can be used to quantitative reconstructions of the past changes. The aim of the study was to gather test sets and to build diatom-based transfer function, which can be used to reconstruct changes in the trophic state and salinity in the coastal lakes on the Polish Baltic coast. In the previous years there were several attempts made to reconstruct these parameters in lagoonal waters on the Baltic coasts in Germany, Denmark, Finland, Netherland, Sweden and Norway. But so far there is no diatom test set and transfer function was built for the Polish coastal lakes. We sample diatoms form 12 lakes located along the polish Baltic coast. At the same time we monitor the physical-chemical conditions in the lakes, which includes lake water chemical composition (chlorides, phosphorous and sulphur), pH, salinity, conductivity, temperature, dissolved oxygen. We collect samples form the lakes as well as from the Baltic Sea and we analyse the whole phytoplankton composition, however the special focus in put on diatoms. The results of the analysis show seasonal changes in the chemical and physical water properties. The diatom assemblage composition and species frequency also changed significantly. This study is a contribution to the projects: NN 306 064 640 financed by National Science Centre, Poland and Virtual Institute ICLEA (Integrated Climate and Landscape Evolution Analysis) funded by the Helmholtz Association.

Characterization of identification errors and uses in localization of poor modal correlation

NASA Astrophysics Data System (ADS)

Martin, Guillaume; Balmes, Etienne; Chancelier, Thierry

2017-05-01

While modal identification is a mature subject, very few studies address the characterization of errors associated with components of a mode shape. This is particularly important in test/analysis correlation procedures, where the Modal Assurance Criterion is used to pair modes and to localize at which sensors discrepancies occur. Poor correlation is usually attributed to modeling errors, but clearly identification errors also occur. In particular with 3D Scanning Laser Doppler Vibrometer measurement, many transfer functions are measured. As a result individual validation of each measurement cannot be performed manually in a reasonable time frame and a notable fraction of measurements is expected to be fairly noisy leading to poor identification of the associated mode shape components. The paper first addresses measurements and introduces multiple criteria. The error measures the difference between test and synthesized transfer functions around each resonance and can be used to localize poorly identified modal components. For intermediate error values, diagnostic of the origin of the error is needed. The level evaluates the transfer function amplitude in the vicinity of a given mode and can be used to eliminate sensors with low responses. A Noise Over Signal indicator, product of error and level, is then shown to be relevant to detect poorly excited modes and errors due to modal property shifts between test batches. Finally, a contribution is introduced to evaluate the visibility of a mode in each transfer. Using tests on a drum brake component, these indicators are shown to provide relevant insight into the quality of measurements. In a second part, test/analysis correlation is addressed with a focus on the localization of sources of poor mode shape correlation. The MACCo algorithm, which sorts sensors by the impact of their removal on a MAC computation, is shown to be particularly relevant. Combined with the error it avoids keeping erroneous modal components. Applied after removal of poor modal components, it provides spatial maps of poor correlation, which help localizing mode shape correlation errors and thus prepare the selection of model changes in updating procedures.

Fluorinion transfer in silver-assisted chemical etching for silicon nanowires arrays

NASA Astrophysics Data System (ADS)

Feng, Tianyu; Xu, Youlong; Zhang, Zhengwei; Mao, Shengchun

2015-08-01

Uniform silicon nanowires arrays (SiNWAs) were fabricated on unpolished rough silicon wafers through KOH pretreatment followed by silver-assisted chemical etching (SACE). Density functional theory (DFT) calculations were used to investigate the function of silver (Ag) at atomic scale in the etching process. Among three adsorption sites of Ag atom on Si(1 0 0) surface, Ag(T4) above the fourth-layer surface Si atoms could transfer fluorinion (F-) to adjacent Si successfully due to its stronger electrostatic attraction force between Ag(T4) and F-, smaller azimuth angle of Fsbnd Ag(T4)sbnd Si, shorter bond length of Fsbnd Si compared with Fsbnd Ag. As F- was transferred to adjacent Si by Ag(T4) one by one, the Si got away from the wafer in the form of SiF4 when it bonded with enough F- while Ag(T4) was still attached onto the Si wafer ready for next transfer. Cyclic voltammetry tests confirmed that Ag can improve the etching rate by transferring F- to Si.

Application of unsteady flow rate evaluations to identify the dynamic transfer function of a cavitatingVenturi

NASA Astrophysics Data System (ADS)

Marie-Magdeleine, A.; Fortes-Patella, R.; Lemoine, N.; Marchand, N.

2012-11-01

This study concerns the simulation of the implementation of the Kinetic Differential Pressure (KDP) method used for the unsteady mass flow rate evaluation in order to identify the dynamic transfer matrix of a cavitatingVenturi. Firstly, the equations of the IZ code used for this simulation are introduced. Next, the methodology for evaluating unsteady pressures and mass flow rates at the inlet and the outlet of the cavitatingVenturi and for identifying the dynamic transfer matrix is presented. Later, the robustness of the method towards measurement uncertainties implemented as a Gaussian white noise is studied. The results of the numerical simulations let us estimate the system linearity domain and to perform the Empirical Transfer Function Evaluation on the inlet frequency per frequency signal and on the chirp signal tests. Then the pressure data obtained with the KDP method is taken and the identification procedure by ETFE and by the user-made Auto-Recursive Moving-Average eXogenous algorithms is performed and the obtained transfer matrix coefficients are compared with those obtained from the simulated input and output data.

The mediating role of insight for long-term improvements in psychodynamic therapy.

PubMed

Johansson, Paul; Høglend, Per; Ulberg, Randi; Amlo, Svein; Marble, Alice; Bøgwald, Kjell-Petter; Sørbye, Oystein; Sjaastad, Mary Cosgrove; Heyerdahl, Oscar

2010-06-01

According to psychoanalytic theory, interpretation of transference leads to increased insight that again leads to improved interpersonal functioning over time. In this study, we performed a full mediational analysis to test whether insight gained during treatment mediates the long-term effects of transference interpretation in dynamic psychotherapy. This study is a randomized clinical trial with a dismantling design. One hundred outpatients seeking psychotherapy for depression, anxiety, personality disorders, and interpersonal problems were randomly assigned to 1 year of weekly sessions of dynamic psychotherapy with transference interpretation or to the same type and duration of treatment with the same therapists but without the use of transference interpretation. Interpersonal functioning and insight were measured pretreatment, posttreatment, and 1 year and 3 years after treatment termination. Contrary to common expectation, patients with a life-long pattern of low quality of object relations and personality disorder pathology profited more from therapy with transference interpretation than from therapy with no transference interpretation. This long-term effect was mediated by an increase in the level of insight during treatment. Insight seems to be a key mechanism of change in dynamic psychotherapy. Our results bridge the gap between clinical theory and empirical research.

Practice and transfer of the frequency structures of continuous isometric force.

PubMed

King, Adam C; Newell, Karl M

2014-04-01

The present study examined the learning, retention and transfer of task outcome and the frequency-dependent properties of isometric force output dynamics. During practice participants produced isometric force to a moderately irregular target pattern either under a constant or variable presentation. Immediate and delayed retention tests examined the persistence of practice-induced changes of force output dynamics and transfer tests investigated performance to novel (low and high) irregular target patterns. The results showed that both constant and variable practice conditions exhibited similar reductions in task error but that the frequency-dependent properties were differentially modified across the entire bandwidth (0-12Hz) of force output dynamics as a function of practice. Task outcome exhibited persistent properties on the delayed retention test whereas the retention of faster time scales processes (i.e., 4-12Hz) of force output was mediated as a function of frequency structure. The structure of the force frequency components during early practice and following a rest interval was characterized by an enhanced emphasis on the slow time scales related to perceptual-motor feedback. The findings support the proposition that there are different time scales of learning at the levels of task outcome and the adaptive frequency bandwidths of force output dynamics. Copyright © 2014 Elsevier B.V. All rights reserved.

Computerized Adaptive Tests Detect Change Following Orthopaedic Surgery in Youth with Cerebral Palsy.

PubMed

Mulcahey, M J; Slavin, Mary D; Ni, Pengsheng; Vogel, Lawrence C; Kozin, Scott H; Haley, Stephen M; Jette, Alan M

2015-09-16

The Cerebral Palsy Computerized Adaptive Test (CP-CAT) is a parent-reported outcomes instrument for measuring lower and upper-extremity function, activity, and global health across impairment levels and a broad age range of children with cerebral palsy (CP). This study was performed to examine whether the Lower Extremity/Mobility (LE) CP-CAT detects change in mobility following orthopaedic surgery in children with CP. This multicenter, longitudinal study involved administration of the LE CP-CAT, the Pediatric Outcomes Data Collection Instrument (PODCI) Transfer/Mobility and Sports/Physical Functioning domains, and the Timed "Up & Go" test (TUG) before and after elective orthopaedic surgery in a convenience sample of 255 children, four to twenty years of age, who had CP and a Gross Motor Function Classification System (GMFCS) level of I, II, or III. Standardized response means (SRMs) and 95% confidence intervals (CIs) were calculated for all measures at six, twelve, and twenty-four months following surgery. SRM estimates for the LE CP-CAT were significantly greater than the SRM estimates for the PODCI Transfer/Mobility domain at twelve months, the PODCI Sports/Physical Functioning domain at twelve months, and the TUG at twelve and twenty-four months. When the results for the children at GMFCS levels I, II, and III were grouped together, the improvements in function detected by the LE CP-CAT at twelve and twenty-four months were found to be greater than the changes detected by the PODCI Transfer/Mobility and Sports/Physical Functioning scales. The LE CP-CAT outperformed the PODCI scales for GMFCS levels I and III at both of these follow-up intervals; none of the scales performed well for patients with GMFCS level II. The results of this study showed that the LE CP-CAT displayed superior sensitivity to change than the PODCI and TUG scales after musculoskeletal surgery in children with CP. Copyright © 2015 by The Journal of Bone and Joint Surgery, Incorporated.

Electromyographic activity after latissimus dorsi transfer: testing of coactivation as a simple tool to assess latissimus dorsi motor learning.

PubMed

Plath, Johannes E; Seiberl, Wolfgang; Beitzel, Knut; Minzlaff, Philipp; Schwirtz, Ansgar; Imhoff, Andreas B; Buchmann, Stefan

2014-08-01

The purpose of this study was to investigate coactivation (CoA) testing as a clinical tool to monitor motor learning after latissimus dorsi tendon transfer. We evaluated 20 patients clinically with the American Shoulder and Elbow Surgeons (ASES) and University of California-Los Angeles (UCLA) outcomes scores, visual analog scale, active external rotation (aER), and isometric strength testing in abduction and external rotation. Measurements of aER were performed while the latissimus dorsi was activated in its new function of external rotation with concomitant activation (coactivation) of its native functions (adduction and extension). Bilateral surface electromyographic (EMG) activity was recorded during aER measurements and the strength testing procedure (EMG activity ratio: with/without CoA). Patients were divided into two groups (excellent/good vs fair/poor) according to the results of the ASES and UCLA scores. The mean follow-up was 57.8 ± 25.2 months. Subdivided by clinical scores, the superior outcome group lost aER with CoA, whereas the inferior outcome group gained aER (UCLA score: -2.2° ± 7.4° vs +4.3° ± 4.1°; P = .031). Patients with inferior outcomes in the ASES score showed higher latissimus dorsi EMG activity ratios (P = .027), suggesting an inadequate motor learning process. Isometric strength testing revealed that the latissimus dorsi transfer had significantly greater activity compared with the contralateral side (external rotation, P = .008; abduction, P = .006) but did not have comparable strength (external rotation, P = .017; abduction, P = .009). Patients with inferior clinical results were more likely to be dependent on CoA to gain external rotation. Therefore, CoA testing may be used as a tool to evaluate the status of postoperative motor learning after latissimus dorsi transfer. Copyright © 2014 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

Short-term music training enhances verbal intelligence and executive function.

PubMed

Moreno, Sylvain; Bialystok, Ellen; Barac, Raluca; Schellenberg, E Glenn; Cepeda, Nicholas J; Chau, Tom

2011-11-01

Researchers have designed training methods that can be used to improve mental health and to test the efficacy of education programs. However, few studies have demonstrated broad transfer from such training to performance on untrained cognitive activities. Here we report the effects of two interactive computerized training programs developed for preschool children: one for music and one for visual art. After only 20 days of training, only children in the music group exhibited enhanced performance on a measure of verbal intelligence, with 90% of the sample showing this improvement. These improvements in verbal intelligence were positively correlated with changes in functional brain plasticity during an executive-function task. Our findings demonstrate that transfer of a high-level cognitive skill is possible in early childhood.

Multi-Instance Metric Transfer Learning for Genome-Wide Protein Function Prediction.

PubMed

Xu, Yonghui; Min, Huaqing; Wu, Qingyao; Song, Hengjie; Ye, Bicui

2017-02-06

Multi-Instance (MI) learning has been proven to be effective for the genome-wide protein function prediction problems where each training example is associated with multiple instances. Many studies in this literature attempted to find an appropriate Multi-Instance Learning (MIL) method for genome-wide protein function prediction under a usual assumption, the underlying distribution from testing data (target domain, i.e., TD) is the same as that from training data (source domain, i.e., SD). However, this assumption may be violated in real practice. To tackle this problem, in this paper, we propose a Multi-Instance Metric Transfer Learning (MIMTL) approach for genome-wide protein function prediction. In MIMTL, we first transfer the source domain distribution to the target domain distribution by utilizing the bag weights. Then, we construct a distance metric learning method with the reweighted bags. At last, we develop an alternative optimization scheme for MIMTL. Comprehensive experimental evidence on seven real-world organisms verifies the effectiveness and efficiency of the proposed MIMTL approach over several state-of-the-art methods.

Performance verification and system parameter identification of spacecraft tape recorder control servo

NASA Technical Reports Server (NTRS)

Mukhopadhyay, A. K.

1979-01-01

Design adequacy of the lead-lag compensator of the frequency loop, accuracy checking of the analytical expression for the electrical motor transfer function, and performance evaluation of the speed control servo of the digital tape recorder used on-board the 1976 Viking Mars Orbiters and Voyager 1977 Jupiter-Saturn flyby spacecraft are analyzed. The transfer functions of the most important parts of a simplified frequency loop used for test simulation are described and ten simulation cases are reported. The first four of these cases illustrate the method of selecting the most suitable transfer function for the hysteresis synchronous motor, while the rest verify and determine the servo performance parameters and alternative servo compensation schemes. It is concluded that the linear methods provide a starting point for the final verification/refinement of servo design by nonlinear time response simulation and that the variation of the parameters of the static/dynamic Coulomb friction is as expected in a long-life space mission environment.

Magnetization Transfer Ratio Relates to Cognitive Impairment in Normal Elderly

PubMed Central

Seiler, Stephan; Pirpamer, Lukas; Hofer, Edith; Duering, Marco; Jouvent, Eric; Fazekas, Franz; Mangin, Jean-Francois; Chabriat, Hugues; Dichgans, Martin; Ropele, Stefan; Schmidt, Reinhold

2014-01-01

Magnetization transfer imaging (MTI) can detect microstructural brain tissue changes and may be helpful in determining age-related cerebral damage. We investigated the association between the magnetization transfer ratio (MTR) in gray and white matter (WM) and cognitive functioning in 355 participants of the Austrian stroke prevention family study (ASPS-Fam) aged 38–86 years. MTR maps were generated for the neocortex, deep gray matter structures, WM hyperintensities, and normal appearing WM (NAWM). Adjusted mixed models determined whole brain and lobar cortical MTR to be directly and significantly related to performance on tests of memory, executive function, and motor skills. There existed an almost linear dose-effect relationship. MTR of deep gray matter structures and NAWM correlated to executive functioning. All associations were independent of demographics, vascular risk factors, focal brain lesions, and cortex volume. Further research is needed to understand the basis of this association at the tissue level, and to determine the role of MTR in predicting cognitive decline and dementia. PMID:25309438

Detecting regional lung properties using audio transfer functions of the respiratory system.

PubMed

Mulligan, K; Adler, A; Goubran, R

2009-01-01

In this study, a novel instrument has been developed for measuring changes in the distribution of lung fluid the respiratory system. The instrument consists of a speaker that inputs a 0-4kHz White Gaussian Noise (WGN) signal into a patient's mouth and an array of 4 electronic stethoscopes, linked via a fully adjustable harness, used to recover signals on the chest surface. The software system for processing the data utilizes the principles of adaptive filtering in order to obtain a transfer function that represents the input-output relationship for the signal as the volume of fluid in the lungs is varied. A chest phantom model was constructed to simulate the behavior of fluid related diseases within the lungs through the injection of varying volumes of water. Tests from the phantom model were compared to healthy subjects. Results show the instrument can obtain similar transfer functions and sound propagation delays between both human and phantom chests.

Performance of the dot product function in radiative transfer code SORD

NASA Astrophysics Data System (ADS)

Korkin, Sergey; Lyapustin, Alexei; Sinyuk, Aliaksandr; Holben, Brent

2016-10-01

The successive orders of scattering radiative transfer (RT) codes frequently call the scalar (dot) product function. In this paper, we study performance of some implementations of the dot product in the RT code SORD using 50 scenarios for light scattering in the atmosphere-surface system. In the dot product function, we use the unrolled loops technique with different unrolling factor. We also considered the intrinsic Fortran functions. We show results for two machines: ifort compiler under Windows, and pgf90 under Linux. Intrinsic DOT_PRODUCT function showed best performance for the ifort. For the pgf90, the dot product implemented with unrolling factor 4 was the fastest. The RT code SORD together with the interface that runs all the mentioned tests are publicly available from ftp://maiac.gsfc.nasa.gov/pub/skorkin/SORD_IP_16B (current release) or by email request from the corresponding (first) author.

Helium Transfer System for the Superconducting Devices at NSRRC

NASA Astrophysics Data System (ADS)

Li, H. C.; Hsiao, F. Z.; Chang, S. H.; Chiou, W. S.

2006-04-01

A helium cryogenic plant with a maximum cooling power of 450 W at 4.5K was installed at the end of the year 2003. This plant has provide the cooling power for the test of one superconducting cavity and the commission of one superconducting magnet for nine months. In November 2004, we installed one helium transfer system in NSRRC's storage ring to fulfill the cooling requirement for the operation of one superconducting cavity and two superconducting magnets. This helium transfer system consists of a switch valve box and the nitrogen-shielding multi-channel transfer lines. The averaged heat leak to the helium process line (including the straight section, the joint, the elbow, the coupling) at liquid helium temperature is specified to be less than 0.1 W/m at 4.2K; the total heat leak of the switching valve box to helium process lines is less than 16 W at 4.2K. In this paper we present the function, design parameters and test result of the helium transfer system. Commissioning results of both the cavity and the magnets using this helium transfer system will be shown as well.

Transfer printing techniques for materials assembly and micro/nanodevice fabrication.

PubMed

Carlson, Andrew; Bowen, Audrey M; Huang, Yonggang; Nuzzo, Ralph G; Rogers, John A

2012-10-09

Transfer printing represents a set of techniques for deterministic assembly of micro-and nanomaterials into spatially organized, functional arrangements with two and three-dimensional layouts. Such processes provide versatile routes not only to test structures and vehicles for scientific studies but also to high-performance, heterogeneously integrated functional systems, including those in flexible electronics, three-dimensional and/or curvilinear optoelectronics, and bio-integrated sensing and therapeutic devices. This article summarizes recent advances in a variety of transfer printing techniques, ranging from the mechanics and materials aspects that govern their operation to engineering features of their use in systems with varying levels of complexity. A concluding section presents perspectives on opportunities for basic and applied research, and on emerging use of these methods in high throughput, industrial-scale manufacturing. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Integrated control and health monitoring capacitive displacement sensor development task. Orbit transfer rocket engine technology program

NASA Technical Reports Server (NTRS)

Collamore, Frank N.

1989-01-01

The development of a miniature multifunction turbomachinery shaft displacement sensor using state-of-the-art non-contract capacitive sensing technology is described. Axial displacement, radial displacement, and speed are sensed using a single probe within the envelope normally required for a single function. A survey of displacement sensing technology is summarized including inductive, capacitive, optical and ultrasonic techniques. The design and operation of an experimental triple function sensor is described. Test results are included showing calibration tests and simultaneous dynamic testing of multiple functions. Recommendations for design changes are made to improve low temperature performance, reliability, and for design of a flight type signal conditioning unit.

Holographic disk with high data transfer rate: its application to an audio response memory.

PubMed

Kubota, K; Ono, Y; Kondo, M; Sugama, S; Nishida, N; Sakaguchi, M

1980-03-15

This paper describes a memory realized with a high data transfer rate using the holographic parallel-processing function and its application to an audio response system that supplies many audio messages to many terminals simultaneously. Digitalized audio messages are recorded as tiny 1-D Fourier transform holograms on a holographic disk. A hologram recorder and a hologram reader were constructed to test and demonstrate the holographic audio response memory feasibility. Experimental results indicate the potentiality of an audio response system with a 2000-word vocabulary and 250-Mbit/sec bit transfer rate.

Mechanical system diagnostics using vibration testing techniques

NASA Technical Reports Server (NTRS)

Mcleod, Catherine D.; Raju, P. K.; Crocker, M. J.

1990-01-01

The 'Cepstrum' technique of vibration-path identification allows the recovery of the transfer function of a system with little knowledge as to its excitation force, by means of a mathematical manipulation of the system output in conjunction with subtraction of part of the output and suitable signal processing. An experimental program has been conducted to evaluate the usefulness of this technique in the cases of simple, cantilever-beam and free-free plate structures as well as in that of a complex mechanical system. On the basis of the transfer functions thus recovered, it was possible to evaluate the shifts in the resonance frequencies of a structure due to the presence of defects.

Acceptance and commissioning of a treatment planning system based on Monte Carlo calculations.

PubMed

Lopez-Tarjuelo, J; Garcia-Molla, R; Juan-Senabre, X J; Quiros-Higueras, J D; Santos-Serra, A; de Marco-Blancas, N; Calzada-Feliu, S

2014-04-01

The Monaco Treatment Planning System (TPS), based on a virtual energy fluence model of the photon beam head components of the linac and a dose computation engine made with Monte Carlo (MC) algorithm X-Ray Voxel MC (XVMC), has been tested before being put into clinical use. An Elekta Synergy with 6 MV was characterized using routine equipment. After the machine's model was installed, a set of functionality, geometric, dosimetric and data transfer tests were performed. The dosimetric tests included dose calculations in water, heterogeneous phantoms and Intensity Modulated Radiation Therapy (IMRT) verifications. Data transfer tests were run for every imaging device, TPS and the electronic medical record linked to Monaco. Functionality and geometric tests were run properly. Dose calculations in water were in accordance with measurements so that, in 95% of cases, differences were up to 1.9%. Dose calculation in heterogeneous media showed expected results found in the literature. IMRT verification results with an ionization chamber led to dose differences lower than 2.5% for points inside a standard gradient. When an 2-D array was used, all the fields passed the g (3%, 3 mm) test with a percentage of succeeding points between 90% and 95%, of which the majority of the mentioned fields had a percentage of succeeding points between 95% and 100%. Data transfer caused problems that had to be solved by means of changing our workflow. In general, tests led to satisfactory results. Monaco performance complied with published international recommendations and scored highly in the dosimetric ambit. However, the problems detected when the TPS was put to work together with our current equipment showed that this kind of product must be completely commissioned, without neglecting data workflow, before treating the first patient.

Quality parameters analysis of optical imaging systems with enhanced focal depth using the Wigner distribution function

PubMed

Zalvidea; Colautti; Sicre

2000-05-01

An analysis of the Strehl ratio and the optical transfer function as imaging quality parameters of optical elements with enhanced focal length is carried out by employing the Wigner distribution function. To this end, we use four different pupil functions: a full circular aperture, a hyper-Gaussian aperture, a quartic phase plate, and a logarithmic phase mask. A comparison is performed between the quality parameters and test images formed by these pupil functions at different defocus distances.

Rational functional representation of flap noise spectra including correction for reflection effects

NASA Technical Reports Server (NTRS)

Miles, J. H.

1974-01-01

A rational function is presented for the acoustic spectra generated by deflection of engine exhaust jets for under-the-wing and over-the-wing versions of externally blown flaps. The functional representation is intended to provide a means for compact storage of data and for data analysis. The expressions are based on Fourier transform functions for the Strouhal normalized pressure spectral density, and on a correction for reflection effects based on Thomas' (1969) N-independent-source model extended by use of a reflected ray transfer function. Curve fit comparisons are presented for blown-flap data taken from turbofan engine tests and from large-scale cold-flow model tests. Application of the rational function to scrubbing noise theory is also indicated.

Aerogel Hybrid Composite Materials: Designs and Testing for Multifunctional Applications

NASA Technical Reports Server (NTRS)

Williams, Martha K.; Fesmire, James E.

2016-01-01

This webinar will introduce the broad spectrum of aerogel composites and their diverse performance properties such as reduced heat transfer to energy storage, and expands specifically on the aerogel/fiber laminate systems and testing methodologies. The multi-functional laminate composite system, AeroFiber, and its construction is designed by varying the type of fiber (e.g. polyester, carbon, Kevlar®, Spectra® or Innegral(TradeMark) and combinations thereof), the aerogel panel type and thickness, and overall layup configuration. The combination and design of materials may be customized and tailored to achieve a range of desired properties in the resulting laminate system. Multi-functional properties include structural strength, impact resistance, reduction in heat transfer, increased fire resistance, mechanical energy absorption, and acoustic energy dampening. Applications include aerospace, aircraft, automotive, boating, building and construction, lightweight portable structures, liquefied natural gas, cryogenics, transportation and energy, sporting equipment, and military protective gear industries.

A study of interior noise levels, noise sources and transmission paths in light aircraft

NASA Technical Reports Server (NTRS)

Hayden, R. E.; Murray, B. S.; Theobald, M. A.

1983-01-01

The interior noise levels and spectral characteristics of 18 single-and twin-engine propeller-driven light aircraft, and source-path diagnosis of a single-engine aircraft which was considered representative of a large part of the fleet were studied. The purpose of the flight surveys was to measure internal noise levels and identify principal noise sources and paths under a carefully controlled and standardized set of flight procedures. The diagnostic tests consisted of flights and ground tests in which various parts of the aircraft, such as engine mounts, the engine compartment, exhaust pipe, individual panels, and the wing strut were instrumented to determine source levels and transmission path strengths using the transfer function technique. Predominant source and path combinations are identified. Experimental techniques are described. Data, transfer function calculations to derive source-path contributions to the cabin acoustic environment, and implications of the findings for noise control design are analyzed.

Laser induced forward transfer of SnO2 for sensing applications using different precursors systems

NASA Astrophysics Data System (ADS)

Mattle, Thomas; Hintennach, Andreas; Lippert, Thomas; Wokaun, Alexander

2013-02-01

This paper presents the transfer of SnO2 by laser induced forward transfer (LIFT) for gas sensor applications. Different donor substrates of SnO2 with and without triazene polymer (TP) as a dynamic release layer were prepared. Transferring these films under different conditions were evaluated by optical microscopy and functionality. Transfers of sputtered SnO2 films do not lead to satisfactory results and transfers of SnO2 nanoparticles are difficult. Transfers of SnO2 nanoparticles can only be achieved when applying a second laser pulse to the already transferred material, which improves the adhesion resulting in a complete pixel. A new approach of decomposing the transfer material during LIFT transfer was developed. Donor films based on UV absorbing metal complex precursors namely, SnCl2(acac)2 were prepared and transferred using the LIFT technique. Transfer conditions were optimized for the different systems, which were deposited onto sensor-like microstructures. The conductivity of the transferred material at temperatures of about 400 ∘C are in a range usable for SnO2 gas sensors. First sensing tests were carried out and the transferred material proved to change conductivity when exposed to ethanol, acetone, and methane.

Goal Management Training and Mindfulness Meditation improve executive functions and transfer to ecological tasks of daily life in polysubstance users enrolled in therapeutic community treatment.

PubMed

Valls-Serrano, Carlos; Caracuel, Alfonso; Verdejo-Garcia, Antonio

2016-08-01

We have previously shown that Goal Management Training+Mindfulness Meditation (GMT+MM) improves executive functions in polysubstance users enrolled in outpatient treatment. The aim of this study was to establish if GMT+MM has similar positive effects on executive functions in polysubstance users in residential treatment, and if executive functions' gains transfer to more ecologically valid goal-oriented tasks. Thirty-two polysbustance users were randomly allocated to eight weeks of GMT+MM (n=16) or control, i.e., no-intervention (n=16); both groups received treatment as usual. Outcome measures included performance in laboratory tasks of basic and complex executive functions (i.e., basic: working memory and inhibition; complex: planning and self-regulation) and in an ecological task of goal-directed behavior (the Multiple Errands Test - contextualized version, MET-CV) measured post-interventions. Results showed that GMT+MM was superior to control in improving basic measures of working memory (Letter-number sequencing; F=4.516, p=0.049) and reflection impulsivity (Information Sampling Test; F=6.217, p=0.018), along with initial thinking times during planning (Zoo Map Test; F=8.143, p=0.008). In addition, GMT+MM was superior to control in improving performance in the MET-CV (task failures; F=8.485, p=0.007). Our findings demonstrate that GMT+MM increases reflective processes and the achievement of goals in daily activities, furthermore ecological test can detects changes easily than laboratory tasks. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Various heterologous cells exhibit interferon induced transfer of viral resistance.

PubMed

Hughes, T K; Blalock, J E; Baron, S

1978-01-01

Previously it was shown that cocultivation of mouse L and human WISH or baby hamster kidney cells in the presence of mouse interferon resulted in decreased viral yield from both cell species. We now show that this phenomenon also occurs when rabbit kidney and human WISH cells, with their corresponding interferons, are cocultivated with human WISH and baby hamster kidney cells, respectively. This finding increases the number of donor cell types to three. The related finding that monkey VERO and chick embryo cells can be recipients of transferred resistance expands the number of heterologous recipient cell species capable of receiving transferred resistence to five. Not all cell types tested have been shown to function in this transfer system. The fact that VERO cells, which do not produce interferon, are capable of receiving transferred resistence is significant because it indicates that the mechanism of transfer does not involve production or interferon by the recipient cells.

Motor learning, retention and transfer after virtual-reality-based training in Parkinson's disease--effect of motor and cognitive demands of games: a longitudinal, controlled clinical study.

PubMed

dos Santos Mendes, Felipe Augusto; Pompeu, José Eduardo; Modenesi Lobo, Alexandra; Guedes da Silva, Keyte; Oliveira, Tatiana de Paula; Peterson Zomignani, Andrea; Pimentel Piemonte, Maria Elisa

2012-09-01

To evaluate the learning, retention and transfer of performance improvements after Nintendo Wii Fit™ training in patients with Parkinson's disease and healthy elderly people. Longitudinal, controlled clinical study. Sixteen patients with early-stage Parkinson's disease and 11 healthy elderly people. Warm-up exercises and Wii Fit training that involved training motor (shifts centre of gravity and step alternation) and cognitive skills. A follow-up evaluative Wii Fit session was held 60 days after the end of training. Participants performed a functional reach test before and after training as a measure of learning transfer. Learning and retention were determined based on the scores of 10 Wii Fit games over eight sessions. Transfer of learning was assessed after training using the functional reach test. Patients with Parkinson's disease showed no deficit in learning or retention on seven of the 10 games, despite showing poorer performance on five games compared with the healthy elderly group. Patients with Parkinson's disease showed marked learning deficits on three other games, independent of poorer initial performance. This deficit appears to be associated with cognitive demands of the games which require decision-making, response inhibition, divided attention and working memory. Finally, patients with Parkinson's disease were able to transfer motor ability trained on the games to a similar untrained task. The ability of patients with Parkinson's disease to learn, retain and transfer performance improvements after training on the Nintendo Wii Fit depends largely on the demands, particularly cognitive demands, of the games involved, reiterating the importance of game selection for rehabilitation purposes. Copyright © 2012 Chartered Society of Physiotherapy. Published by Elsevier Ltd. All rights reserved.

Executive Functioning in Three Groups of Pupils in D-KEFSs: Selected Issues in Adapting the Test Battery for Slovakia

ERIC Educational Resources Information Center

Ferjencík, Ján; Slavkovská, Miriam; Kresila, Juraj

2015-01-01

The paper reports on the adaptation of a D-KEFS test battery for Slovakia. Drawing on concrete examples, it describes and illustrates the key issues relating to the transfer of test items from one socio-cultural environment to another. The standardisation sample of the population of Slovak pupils in the fourth year of primary school included 250…

The use of fractional order derivatives for eddy current non-destructive testing

NASA Astrophysics Data System (ADS)

Sikora, Ryszard; Grzywacz, Bogdan; Chady, Tomasz

2018-04-01

The paper presents the possibility of using the fractional derivatives for non-destructive testing when a multi-frequency method based on eddy current is applied. It is shown that frequency characteristics obtained during tests can be approximated by characteristics of a proposed model in the form of fractional order transfer function, and values of parameters of this model can be utilized for detection and identification of defects.

Valence and charge-transfer optical properties for some SinCm (m, n ≤ 12) clusters: Comparing TD-DFT, complete-basis-limit EOMCC, and benchmarks from spectroscopy.

PubMed

Lutz, Jesse J; Duan, Xiaofeng F; Ranasinghe, Duminda S; Jin, Yifan; Margraf, Johannes T; Perera, Ajith; Burggraf, Larry W; Bartlett, Rodney J

2018-05-07

Accurate optical characterization of the closo-Si 12 C 12 molecule is important to guide experimental efforts toward the synthesis of nano-wires, cyclic nano-arrays, and related array structures, which are anticipated to be robust and efficient exciton materials for opto-electronic devices. Working toward calibrated methods for the description of closo-Si 12 C 12 oligomers, various electronic structure approaches are evaluated for their ability to reproduce measured optical transitions of the SiC 2 , Si 2 C n (n = 1-3), and Si 3 C n (n = 1, 2) clusters reported earlier by Steglich and Maier [Astrophys. J. 801, 119 (2015)]. Complete-basis-limit equation-of-motion coupled-cluster (EOMCC) results are presented and a comparison is made between perturbative and renormalized non-iterative triples corrections. The effect of adding a renormalized correction for quadruples is also tested. Benchmark test sets derived from both measurement and high-level EOMCC calculations are then used to evaluate the performance of a variety of density functionals within the time-dependent density functional theory (TD-DFT) framework. The best-performing functionals are subsequently applied to predict valence TD-DFT excitation energies for the lowest-energy isomers of Si n C and Si n-1 C 7-n (n = 4-6). TD-DFT approaches are then applied to the Si n C n (n = 4-12) clusters and unique spectroscopic signatures of closo-Si 12 C 12 are discussed. Finally, various long-range corrected density functionals, including those from the CAM-QTP family, are applied to a charge-transfer excitation in a cyclic (Si 4 C 4 ) 4 oligomer. Approaches for gauging the extent of charge-transfer character are also tested and EOMCC results are used to benchmark functionals and make recommendations.

Breadboard stellar tracker system test report

NASA Technical Reports Server (NTRS)

Kollodge, J. C.; Parrish, K. A.

1984-01-01

BASD has, in the past, developed several unique position tracking algorithms for charge transfer device (CTD) sensors. These algorithms provide an interpixel transfer function with the following characteristics: (1) high linearity; (2) simplified track logic; (3) high gain; and (4) high noise rejection. A previous test program using the GE charge injection device (CID) showed that accuracy for BASD's breadboard was limited to approximately 2% of a pixel (1 sigma) whereas analysis and simulation indicated the limit should be less than 0.5% of a pixel, assuming the limit to be detector response and dark current noise. The test program was conducted under NASA contract No. NAS8-34263. The test approach for that program did not provide sufficient data to identify the sources of error and left open the amount of contribution from parameters such as image distribution, geometric distortion and system alignment errors.

Round robin test on V-shape bio-imaging transfer standard for determination of the instrument transfer function of 3D optical profilers

NASA Astrophysics Data System (ADS)

Bermudez, Carlos; Artigas, Roger; Martinez, Pol; Nolvi, Anton; Järvinen, Miikka; Hæggström, Edward; Kassamakov, Ivan

2018-02-01

A V-shape Bio-Transfer-Standard (V-BTS), developed and produced at the University of Helsinki (UH), was measured in two laboratories. In comparison to Siemens Star calibration specimens, the V-BTS performs better at high lateral frequencies close to the diffraction limit of the optical instrument. This permits determining of the Instrument Transfer Function (ITF). The V-BTS features two lipid bilayer steps that partly overlap each other at an angle of 20°, with an average height of 4.6 +/- 0.1 nm. The Round Robin (RR) test aims to determine whether the V-BTS and the developed application protocol work with different optical profilers in different laboratories. First the artefact was measured at Sensofar-Tech, S.L. using an S-neox profiler working in Phase Shifting Interferometry mode. Then V-BTS was measured at UH using a custom-built Scanning White Light Interferometer. All measurements done by four different operators at the two laboratories have a range or standard deviation of +/-0.1 nm which agrees with the theoretical estimates and with measurements done using an atomic force microscope and with a surface plasmon resonance based instrument. The RR results show the applicability of the V-BTS for calibration and for ITF characterization of 3D optical profilers.

Physical instrumental vetoes for gravitational-wave burst triggers

NASA Astrophysics Data System (ADS)

Ajith, P.; Hewitson, M.; Smith, J. R.; Grote, H.; Hild, S.; Strain, K. A.

2007-08-01

We present a robust strategy to veto certain classes of instrumental glitches that appear at the output of interferometric gravitational-wave detectors. This veto method is “physical” in the sense that, in order to veto a burst trigger, we make use of our knowledge of the coupling of different detector subsystems to the main detector output. The main idea behind this method is that the noise in an instrumental channel X can be transferred to the detector output (channel H) using the transfer function from X to H, provided the noise coupling is linear and the transfer function is unique. If a nonstationarity in channel H is causally related to one in channel X, the two have to be consistent with the transfer function. We formulate two methods for testing the consistency between the burst triggers in channel X and channel H. One method makes use of the null stream constructed from channel H and the transferred channel X, and the second involves cross correlating the two. We demonstrate the efficiency of the veto by “injecting” instrumental glitches in the hardware of the GEO 600 detector. The veto safety is demonstrated by performing gravitational-wave like hardware injections. We also show an example application of this method using 5 days of data from the fifth science run of GEO 600. The method is found to have very high veto efficiency with a very low accidental veto rate.

Horizontal gene transfer is more frequent with increased heterotrophy and contributes to parasite adaptation

PubMed Central

Yang, Zhenzhen; Zhang, Yeting; Wafula, Eric K.; Honaas, Loren A.; Ralph, Paula E.; Jones, Sam; Clarke, Christopher R.; Liu, Siming; Su, Chun; Zhang, Huiting; Altman, Naomi S.; Schuster, Stephan C.; Timko, Michael P.; Yoder, John I.; dePamphilis, Claude W.

2016-01-01

Horizontal gene transfer (HGT) is the transfer of genetic material across species boundaries and has been a driving force in prokaryotic evolution. HGT involving eukaryotes appears to be much less frequent, and the functional implications of HGT in eukaryotes are poorly understood. We test the hypothesis that parasitic plants, because of their intimate feeding contacts with host plant tissues, are especially prone to horizontal gene acquisition. We sought evidence of HGTs in transcriptomes of three parasitic members of Orobanchaceae, a plant family containing species spanning the full spectrum of parasitic capabilities, plus the free-living Lindenbergia. Following initial phylogenetic detection and an extensive validation procedure, 52 high-confidence horizontal transfer events were detected, often from lineages of known host plants and with an increasing number of HGT events in species with the greatest parasitic dependence. Analyses of intron sequences in putative donor and recipient lineages provide evidence for integration of genomic fragments far more often than retro-processed RNA sequences. Purifying selection predominates in functionally transferred sequences, with a small fraction of adaptively evolving sites. HGT-acquired genes are preferentially expressed in the haustorium—the organ of parasitic plants—and are strongly biased in predicted gene functions, suggesting that expression products of horizontally acquired genes are contributing to the unique adaptive feeding structure of parasitic plants. PMID:27791104

Radiative heat transfer in strongly forward scattering media using the discrete ordinates method

NASA Astrophysics Data System (ADS)

Granate, Pedro; Coelho, Pedro J.; Roger, Maxime

2016-03-01

The discrete ordinates method (DOM) is widely used to solve the radiative transfer equation, often yielding satisfactory results. However, in the presence of strongly forward scattering media, this method does not generally conserve the scattering energy and the phase function asymmetry factor. Because of this, the normalization of the phase function has been proposed to guarantee that the scattering energy and the asymmetry factor are conserved. Various authors have used different normalization techniques. Three of these are compared in the present work, along with two other methods, one based on the finite volume method (FVM) and another one based on the spherical harmonics discrete ordinates method (SHDOM). In addition, the approximation of the Henyey-Greenstein phase function by a different one is investigated as an alternative to the phase function normalization. The approximate phase function is given by the sum of a Dirac delta function, which accounts for the forward scattering peak, and a smoother scaled phase function. In this study, these techniques are applied to three scalar radiative transfer test cases, namely a three-dimensional cubic domain with a purely scattering medium, an axisymmetric cylindrical enclosure containing an emitting-absorbing-scattering medium, and a three-dimensional transient problem with collimated irradiation. The present results show that accurate predictions are achieved for strongly forward scattering media when the phase function is normalized in such a way that both the scattered energy and the phase function asymmetry factor are conserved. The normalization of the phase function may be avoided using the FVM or the SHDOM to evaluate the in-scattering term of the radiative transfer equation. Both methods yield results whose accuracy is similar to that obtained using the DOM along with normalization of the phase function. Very satisfactory predictions were also achieved using the delta-M phase function, while the delta-Eddington phase function and the transport approximation may perform poorly.

Transfer of short-term motor learning across the lower limbs as a function of task conception and practice order.

PubMed

Stöckel, Tino; Wang, Jinsung

2011-11-01

Interlimb transfer of motor learning, indicating an improvement in performance with one limb following training with the other, often occurs asymmetrically (i.e., from non-dominant to dominant limb or vice versa, but not both). In the present study, we examined whether interlimb transfer of the same motor task could occur asymmetrically and in opposite directions (i.e., from right to left leg vs. left to right leg) depending on individuals' conception of the task. Two experimental conditions were tested: In a dynamic control condition, the process of learning was facilitated by providing the subjects with a type of information that forced them to focus on dynamic features of a given task (force impulse); and in a spatial control condition, it was done with another type of information that forced them to focus on visuomotor features of the same task (distance). Both conditions employed the same leg extension task. In addition, a fully-crossed transfer paradigm was used in which one group of subjects initially practiced with the right leg and were tested with the left leg for a transfer test, while the other group used the two legs in the opposite order. The results showed that the direction of interlimb transfer varied depending on the condition, such that the right and the left leg benefited from initial training with the opposite leg only in the spatial and the dynamic condition, respectively. Our finding suggests that manipulating the conception of a leg extension task has a substantial influence on the pattern of interlimb transfer in such a way that the direction of transfer can even be opposite depending on whether the task is conceived as a dynamic or spatial control task. Copyright © 2011 Elsevier Inc. All rights reserved.

Modulation transfer function cascade model for a sampled IR imaging system.

PubMed

de Luca, L; Cardone, G

1991-05-01

The performance of the infrared scanning radiometer (IRSR) is strongly stressed in convective heat transfer applications where high spatial frequencies in the signal that describes the thermal image are present. The need to characterize more deeply the system spatial resolution has led to the formulation of a cascade model for the evaluation of the actual modulation transfer function of a sampled IR imaging system. The model can yield both the aliasing band and the averaged modulation response for a general sampling subsystem. For a line scan imaging system, which is the case of a typical IRSR, a rule of thumb that states whether the combined sampling-imaging system is either imaging-dependent or sampling-dependent is proposed. The model is tested by comparing it with other noncascade models as well as by ad hoc measurements performed on a commercial digitized IRSR.

Orbital Transfer Vehicle Oxygen Turbopump Technology. Final Report, Volume 1. Design, Fabrication, and Hydrostatic Bearing Testing

DTIC Science & Technology

1990-12-01

Temperature Distance Sensors -. ...................... 188 Start Transient 4.5-7 Distance Sensor Signal as a Function of Speed...189 4.5-8 Distance Sensor Signal as a Function of Speed ......................................... 190 4.5-9 Cryogenic Operation of...Distance Sensors at 72,000 RPM ........................ 192 Steady State 4.5-10 Cryogenic Operation of Distance Sensor Through Start

Enhancing Executive Functions Among Dutch Elementary School Children Using the Train Your Mind Program: Protocol for a Cluster Randomized Trial.

PubMed

Bervoets, Joachim; Jonkman, Lisa M; Mulkens, Sandra; de Vries, Hein; Kok, Gerjo

2018-06-07

Executive functions are higher cognitive control functions, which are essential to physical and psychological well-being, academic performance, and healthy social relationships. Executive functions can be trained, albeit without broad transfer, to this date. Broad transfer entails the translation of improved cognitive functions to daily life (behaviors). The intervention Train your Mind was designed to train executive functions among elementary school children aged 9 to 11 years, and obtain broad transfer in terms of enhanced physical activity, healthy eating, and socioemotional regulation. This paper aims to describe the cluster randomized trial to test the effectiveness of the Train your Mind intervention. Train your Mind was integrated into the existing school curriculum for 8 months (25 weeks excluding holidays). The effectiveness of the intervention was tested in a cluster randomized trial comprising 13 schools, 34 groups (school classes), and 800 children, using a battery of 6 computer tasks at pre- and postmeasurement. Each of the 3 core executive functions was measured by 2 tasks (Flanker and Go/No-Go; N-Back and Running Span; Attention Switching Task and Dots/Triangles). Moreover, we administered questionnaires that measure emotion-regulation, cognitive errors, physical activity, dietary habits, and the psycho-social determinants of diet and physical activity. Body mass index was also measured. Multilevel analyses will account for clustering at the school and group levels, and randomization took place at the school level. Results are currently being analyzed. The main purpose of this study is to test Train your Mind's effectiveness in enhancing executive functions. Second, we investigate whether increased executive functions lead to improved physical activity and healthy eating. If found effective, executive function training could easily be integrated into school curricula everywhere, and as such, boost health, academic performance, and emotion-regulation of elementary school children, in a cost-effective manner. Netherlands Trial Register NTR5804; http://www.trialregister.nl/trialreg/admin/rctview.asp?TC=5804 (Archived by WebCite at http://www.webcitation.org/6z9twosJ8). RR1-10.2196/7908. ©Joachim Bervoets, Lisa M Jonkman, Sandra Mulkens, Hein de Vries, Gerjo Kok. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 07.06.2018.

Patient-reported outcome measures versus inertial performance-based outcome measures: A prospective study in patients undergoing primary total knee arthroplasty.

PubMed

Bolink, S A A N; Grimm, B; Heyligers, I C

2015-12-01

Outcome assessment of total knee arthroplasty (TKA) by subjective patient reported outcome measures (PROMs) may not fully capture the functional (dis-)abilities of relevance. Objective performance-based outcome measures could provide distinct information. An ambulant inertial measurement unit (IMU) allows kinematic assessment of physical performance and could potentially be used for routine follow-up. To investigate the responsiveness of IMU measures in patients following TKA and compare outcomes with conventional PROMs. Patients with end stage knee OA (n=20, m/f=7/13; age=67.4 standard deviation 7.7 years) were measured preoperatively and one year postoperatively. IMU measures were derived during gait, sit-stand transfers and block step-up transfers. PROMs were assessed by using the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) and Knee Society Score (KSS). Responsiveness was calculated by the effect size, correlations were calculated with Spearman's rho correlation coefficient. One year after TKA, patients performed significantly better at gait, sit-to-stand transfers and block step-up transfers. Measures of time and kinematic IMU measures demonstrated significant improvements postoperatively for each performance-based test. The largest improvement was found in block step-up transfers (effect size=0.56-1.20). WOMAC function score and KSS function score demonstrated moderate correlations (Spearman's rho=0.45-0.74) with some of the physical performance-based measures pre- and postoperatively. To characterize the changes in physical function after TKA, PROMs could be supplemented by performance-based measures, assessing function during different activities and allowing kinematic characterization with an ambulant IMU. Copyright © 2015 Elsevier B.V. All rights reserved.

Prior schemata transfer as an account for assessing the intuitive use of new technology.

PubMed

Fischer, Sandrine; Itoh, Makoto; Inagaki, Toshiyuki

2015-01-01

New devices are considered intuitive when they allow users to transfer prior knowledge. Drawing upon fundamental psychology experiments that distinguish prior knowledge transfer from new schema induction, a procedure was specified for assessing intuitive use. This procedure was tested with 31 participants who, prior to using an on-board computer prototype, studied its screenshots in reading vs. schema induction conditions. Distinct patterns of transfer or induction resulted for features of the prototype whose functions were familiar or unfamiliar, respectively. Though moderated by participants' cognitive style, these findings demonstrated a means for quantitatively assessing transfer of prior knowledge as the operation that underlies intuitive use. Implications for interface evaluation and design, as well as potential improvements to the procedure, are discussed. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The Evolution of a More Rigorous Approach to Benefit Transfer: Benefit Function Transfer

NASA Astrophysics Data System (ADS)

Loomis, John B.

1992-03-01

The desire for economic values of recreation for unstudied recreation resources dates back to the water resource development benefit-cost analyses of the early 1960s. Rather than simply applying existing estimates of benefits per trip to the study site, a fairly rigorous approach was developed by a number of economists. This approach involves application of travel cost demand equations and contingent valuation benefit functions from existing sites to the new site. In this way the spatial market of the new site (i.e., its differing own price, substitute prices and population distribution) is accounted for in the new estimate of total recreation benefits. The assumptions of benefit transfer from recreation sites in one state to another state for the same recreation activity is empirically tested. The equality of demand coefficients for ocean sport salmon fishing in Oregon versus Washington and for freshwater steelhead fishing in Oregon versus Idaho is rejected. Thus transfer of either demand equations or average benefits per trip are likely to be in error. Using the Oregon steelhead equation, benefit transfers to rivers within the state are shown to be accurate to within 5-15%.

Motor strategies and bilateral transfer in sensorimotor learning of patients with subacute stroke and healthy subjects. A randomized controlled trial.

PubMed

Iosa, M; Morone, G; Ragaglini, M R; Fusco, A; Paolucci, S

2013-06-01

Bilateral transfer, i.e. the capacity to transfer from one to the other hand a learned motor skill, may help the recovery of upper limb functions after stroke. To investigate the motor strategies at the basis of sensorimotor learning involved in bilateral transfer. Randomized controlled trial. Neurorehabilitation Hospital. Eighty right-handed participants (65 ± 13 years old): 40 patients with subacute stroke, 40 control healthy subjects. Subjects performed the 9 hole-peg-test twice in an order defined by random allocation: first with low and then with high skilled hand (LS-HS) or the reverse (HS-LS). Time spent to complete the test and filling sequence were recorded, together with maximum pinch force (assessed using a dynamometer), upper limb functioning (Motricity Index), spasticity (modified Ashworth Scale), limb dominance (Edinburgh Handeness Inventory). As expected, in patients, the performance was found related to the residual pinch force (P<0.001), upper limb motricity (P=0.006) and side of hemiparesis (P=0.016). The performances of all subjects improved more in HS-LS than in LS-HS subgroups (P=0.043). The strategy adopted in the first trial influenced the velocity in the second one (P=0.030). Bilateral transfer was observed from high to low skilled hand. Learning was not due to a mere sequence repetition, but on a strategy chosen on the basis of the previous performance. The affected hand of patients with subacute stroke may benefit from sensorimotor learning occurred with the un-affected hand.

Performance and heat transfer characteristics of a carbon monoxide/oxygen rocket engine

NASA Technical Reports Server (NTRS)

Linne, Diane L.

1993-01-01

The combustion and heat transfer characteristics of a carbon monoxide and oxygen rocket engine were evaluated. The test hardware consisted of a calorimeter combustion chamber with a heat sink nozzle and an eighteen element concentric tube injector. Experimental results are given at chamber pressures of 1070 and 3070 kPa, and over a mixture ratio range of 0.3 to 1.0. Experimental C efficiency was between 95 and 96.5 percent. Heat transfer results are discussed both as a function of mixture ratio and axial distance in the chamber. They are also compared to a Nusselt number correlation for fully developed turbulent flow.

Multisensory perceptual learning of temporal order: audiovisual learning transfers to vision but not audition.

PubMed

Alais, David; Cass, John

2010-06-23

An outstanding question in sensory neuroscience is whether the perceived timing of events is mediated by a central supra-modal timing mechanism, or multiple modality-specific systems. We use a perceptual learning paradigm to address this question. Three groups were trained daily for 10 sessions on an auditory, a visual or a combined audiovisual temporal order judgment (TOJ). Groups were pre-tested on a range TOJ tasks within and between their group modality prior to learning so that transfer of any learning from the trained task could be measured by post-testing other tasks. Robust TOJ learning (reduced temporal order discrimination thresholds) occurred for all groups, although auditory learning (dichotic 500/2000 Hz tones) was slightly weaker than visual learning (lateralised grating patches). Crossmodal TOJs also displayed robust learning. Post-testing revealed that improvements in temporal resolution acquired during visual learning transferred within modality to other retinotopic locations and orientations, but not to auditory or crossmodal tasks. Auditory learning did not transfer to visual or crossmodal tasks, and neither did it transfer within audition to another frequency pair. In an interesting asymmetry, crossmodal learning transferred to all visual tasks but not to auditory tasks. Finally, in all conditions, learning to make TOJs for stimulus onsets did not transfer at all to discriminating temporal offsets. These data present a complex picture of timing processes. The lack of transfer between unimodal groups indicates no central supramodal timing process for this task; however, the audiovisual-to-visual transfer cannot be explained without some form of sensory interaction. We propose that auditory learning occurred in frequency-tuned processes in the periphery, precluding interactions with more central visual and audiovisual timing processes. Functionally the patterns of featural transfer suggest that perceptual learning of temporal order may be optimised to object-centered rather than viewer-centered constraints.

Changes in permeability of the alveolar-capillary barrier in firefighters.

PubMed Central

Minty, B D; Royston, D; Jones, J G; Smith, D J; Searing, C S; Beeley, M

1985-01-01

The effect on alveolar-capillary barrier permeability of chronic exposure to a smoke produced by the partial combusion of diesel oil, paraffin, and wood was examined. An index of permeability was determined from the rate of transfer from the lung into the blood of the hydrophilic, labelled chelate 99mTc diethylene triamine penta-acetate (MW 492 dalton). The results of this test were expressed as the half time clearance of the tracer from the lung into the blood (T1/2 LB). The study was carried out at the Royal Naval Firefighting School, HMS Excellent. Permeability index was measured on seven non-smoking naval firefighting instructors who had worked at the school for periods of longer than two and a half months. Tests of airway function and carbon monoxide transfer factor were performed on four of these seven instructors. The results of the permeability index showed a T1/2 LB of 26 min +/- 5 (SEM) which differed significantly from that of normal non-smokers. By contrast all other lung function tests had values within the predicted normal range. PMID:3899161

Changes in permeability of the alveolar-capillary barrier in firefighters.

PubMed

Minty, B D; Royston, D; Jones, J G; Smith, D J; Searing, C S; Beeley, M

1985-09-01

The effect on alveolar-capillary barrier permeability of chronic exposure to a smoke produced by the partial combusion of diesel oil, paraffin, and wood was examined. An index of permeability was determined from the rate of transfer from the lung into the blood of the hydrophilic, labelled chelate 99mTc diethylene triamine penta-acetate (MW 492 dalton). The results of this test were expressed as the half time clearance of the tracer from the lung into the blood (T1/2 LB). The study was carried out at the Royal Naval Firefighting School, HMS Excellent. Permeability index was measured on seven non-smoking naval firefighting instructors who had worked at the school for periods of longer than two and a half months. Tests of airway function and carbon monoxide transfer factor were performed on four of these seven instructors. The results of the permeability index showed a T1/2 LB of 26 min +/- 5 (SEM) which differed significantly from that of normal non-smokers. By contrast all other lung function tests had values within the predicted normal range.

5 CFR 351.303 - Identification of positions with a transferring function.

Code of Federal Regulations, 2013 CFR

2013-01-01

... transferring function. 351.303 Section 351.303 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS REDUCTION IN FORCE Transfer of Function § 351.303 Identification of positions with a transferring function. (a) The competitive area losing the function is responsible for identifying the...

5 CFR 351.303 - Identification of positions with a transferring function.

Code of Federal Regulations, 2014 CFR

2014-01-01

... transferring function. 351.303 Section 351.303 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS REDUCTION IN FORCE Transfer of Function § 351.303 Identification of positions with a transferring function. (a) The competitive area losing the function is responsible for identifying the...

Probabilistic migration modelling focused on functional barrier efficiency and low migration concepts in support of risk assessment.

PubMed

Brandsch, Rainer

2017-10-01

Migration modelling provides reliable migration estimates from food-contact materials (FCM) to food or food simulants based on mass-transfer parameters like diffusion and partition coefficients related to individual materials. In most cases, mass-transfer parameters are not readily available from the literature and for this reason are estimated with a given uncertainty. Historically, uncertainty was accounted for by introducing upper limit concepts first, turning out to be of limited applicability due to highly overestimated migration results. Probabilistic migration modelling gives the possibility to consider uncertainty of the mass-transfer parameters as well as other model inputs. With respect to a functional barrier, the most important parameters among others are the diffusion properties of the functional barrier and its thickness. A software tool that accepts distribution as inputs and is capable of applying Monte Carlo methods, i.e., random sampling from the input distributions of the relevant parameters (i.e., diffusion coefficient and layer thickness), predicts migration results with related uncertainty and confidence intervals. The capabilities of probabilistic migration modelling are presented in the view of three case studies (1) sensitivity analysis, (2) functional barrier efficiency and (3) validation by experimental testing. Based on the predicted migration by probabilistic migration modelling and related exposure estimates, safety evaluation of new materials in the context of existing or new packaging concepts is possible. Identifying associated migration risk and potential safety concerns in the early stage of packaging development is possible. Furthermore, dedicated material selection exhibiting required functional barrier efficiency under application conditions becomes feasible. Validation of the migration risk assessment by probabilistic migration modelling through a minimum of dedicated experimental testing is strongly recommended.

7T Magnetization Transfer and Chemical Exchange Saturation Transfer MRI of Cortical Gray Matter: Can We Detect Neurochemical and Macromolecular Abnormalities?

DTIC Science & Technology

2014-10-21

measures working memory • Trail making test (both A and B): measures planning/executive function • "Black Box” (choice reaction time, critical flicker ...associated with SIR imaging. The former of these was mitigated by developing a novel B+ and !1B insensitive in- version composite pulse (Fig. 2) and...employing a low-flip angle TFE readout; the latter was mitigated by the efficiency of the TFE readout along with additional protocol optimization

Test Operations Procedure (TOP) 6-3-044. Optical Transfer Function

DTIC Science & Technology

2009-07-27

Mounting Fixtures As required Alignment Periscope See section 4.1.6 TOP 6-3-040 27 July 2009 3 3. REQUIRED TEST CONDITIONS. 3.1 Pre-test...carefully selected. The stabilized cast iron lathe bed type, typically 2-3 m long, provides adequate support for mounting the various assemblies...combined size and weight of some vehicle mounted sights, a special mounting fixture , perhaps including a periscopic system may be required. It is

Exact and conceptual repetition dissociate conceptual memory tests: problems for transfer appropriate processing theory.

PubMed

McDermott, K B; Roediger, H L

1996-03-01

Three experiments examined whether a conceptual implicit memory test (specifically, category instance generation) would exhibit repetition effects similar to those found in free recall. The transfer appropriate processing account of dissociations among memory tests led us to predict that the tests would show parallel effects; this prediction was based upon the theory's assumption that conceptual tests will behave similarly as a function of various independent variables. In Experiment 1, conceptual repetition (i.e., following a target word [e.g., puzzles] with an associate [e.g., jigsaw]) did not enhance priming on the instance generation test relative to the condition of simply presenting the target word once, although this manipulation did affect free recall. In Experiment 2, conceptual repetition was achieved by following a picture with its corresponding word (or vice versa). In this case, there was an effect of conceptual repetition on free recall but no reliable effect on category instance generation or category cued recall. In addition, we obtained a picture superiority effect in free recall but not in category instance generation. In the third experiment, when the same study sequence was used as in Experiment 1, but with instructions that encouraged relational processing, priming on the category instance generation task was enhanced by conceptual repetition. Results demonstrate that conceptual memory tests can be dissociated and present problems for Roediger's (1990) transfer appropriate processing account of dissociations between explicit and implicit tests.

Electromagnetic Compatibility Testing Studies

NASA Technical Reports Server (NTRS)

Trost, Thomas F.; Mitra, Atindra K.

1996-01-01

This report discusses the results on analytical models and measurement and simulation of statistical properties from a study of microwave reverberation (mode-stirred) chambers performed at Texas Tech University. Two analytical models of power transfer vs. frequency in a chamber, one for antenna-to-antenna transfer and the other for antenna to D-dot sensor, were experimentally validated in our chamber. Two examples are presented of the measurement and calculation of chamber Q, one for each of the models. Measurements of EM power density validate a theoretical probability distribution on and away from the chamber walls and also yield a distribution with larger standard deviation at frequencies below the range of validity of the theory. Measurements of EM power density at pairs of points which validate a theoretical spatial correlation function on the chamber walls and also yield a correlation function with larger correlation length, R(sub corr), at frequencies below the range of validity of the theory. A numerical simulation, employing a rectangular cavity with a moving wall shows agreement with the measurements. The determination that the lowest frequency at which the theoretical spatial correlation function is valid in our chamber is considerably higher than the lowest frequency recommended by current guidelines for utilizing reverberation chambers in EMC testing. Two suggestions have been made for future studies related to EMC testing.

Assessing spectral and temporal processing in children and adults using temporal modulation transfer function (TMTF), Iterated Ripple Noise (IRN) perception, and spectral ripple discrimination (SRD).

PubMed

Peter, Varghese; Wong, Kogo; Narne, Vijaya Kumar; Sharma, Mridula; Purdy, Suzanne C; McMahon, Catherine

2014-02-01

There are many clinically available tests for the assessment of auditory processing skills in children and adults. However, there is limited data available on the maturational effects on the performance on these tests. The current study investigated maturational effects on auditory processing abilities using three psychophysical measures: temporal modulation transfer function (TMTF), iterated ripple noise (IRN) perception, and spectral ripple discrimination (SRD). A cross-sectional study. Three groups of subjects were tested: 10 adults (18-30 yr), 10 older children (12-18 yr), and 10 young children (8-11 yr) Temporal envelope processing was measured by obtaining thresholds for amplitude modulation detection as a function of modulation frequency (TMTF; 4, 8, 16, 32, 64, and 128 Hz). Temporal fine structure processing was measured using IRN, and spectral processing was measured using SRD. The results showed that young children had significantly higher modulation thresholds at 4 Hz (TMTF) compared to the other two groups and poorer SRD scores compared to adults. The results on IRN did not differ across groups. The results suggest that different aspects of auditory processing mature at different age periods and these maturational effects need to be considered while assessing auditory processing in children. American Academy of Audiology.

An examination of mediators of the transfer of cognitive speed of processing training to everyday functional performance.

PubMed

Edwards, Jerri D; Ruva, Christine L; O'Brien, Jennifer L; Haley, Christine B; Lister, Jennifer J

2013-06-01

The purpose of these analyses was to examine mediators of the transfer of cognitive speed of processing training to improved everyday functional performance (J. D. Edwards, V. G. Wadley,, D. E. Vance, D. L. Roenker, & K. K. Ball, 2005, The impact of speed of processing training on cognitive and everyday performance. Aging & Mental Health, 9, 262-271). Cognitive speed of processing and visual attention (as measured by the Useful Field of View Test; UFOV) were examined as mediators of training transfer. Secondary data analyses were conducted from the Staying Keen in Later Life (SKILL) study, a randomized cohort study including 126 community dwelling adults 63 to 87 years of age. In the SKILL study, participants were randomized to an active control group or cognitive speed of processing training (SOPT), a nonverbal, computerized intervention involving perceptual practice of visual tasks. Prior analyses found significant effects of training as measured by the UFOV and Timed Instrumental Activities of Daily Living (TIADL) Tests. Results from the present analyses indicate that speed of processing for a divided attention task significantly mediated the effect of SOPT on everyday performance (e.g., TIADL) in a multiple mediation model accounting for 91% of the variance. These findings suggest that everyday functional improvements found from SOPT are directly attributable to improved UFOV performance, speed of processing for divided attention in particular. Targeting divided attention in cognitive interventions may be important to positively affect everyday functioning among older adults. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Calibration of the modulation transfer function of surface profilometers with binary pseudo-random test standards: expanding the application range

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yashchuk, Valeriy V.; Anderson, Erik H.; Barber, Samuel K.

2011-03-14

A modulation transfer function (MTF) calibration method based on binary pseudo-random (BPR) gratings and arrays [Proc. SPIE 7077-7 (2007), Opt. Eng. 47, 073602 (2008)] has been proven to be an effective MTF calibration method for a number of interferometric microscopes and a scatterometer [Nucl. Instr. and Meth. A616, 172 (2010)]. Here we report on a further expansion of the application range of the method. We describe the MTF calibration of a 6 inch phase shifting Fizeau interferometer. Beyond providing a direct measurement of the interferometer's MTF, tests with a BPR array surface have revealed an asymmetry in the instrument's datamore » processing algorithm that fundamentally limits its bandwidth. Moreover, the tests have illustrated the effects of the instrument's detrending and filtering procedures on power spectral density measurements. The details of the development of a BPR test sample suitable for calibration of scanning and transmission electron microscopes are also presented. Such a test sample is realized as a multilayer structure with the layer thicknesses of two materials corresponding to BPR sequence. The investigations confirm the universal character of the method that makes it applicable to a large variety of metrology instrumentation with spatial wavelength bandwidths from a few nanometers to hundreds of millimeters.« less

Relative performance of several inexpensive accelerometers

USGS Publications Warehouse

Evans, John R.; Rogers, John A.

1995-01-01

We examined the performance of several low-cost accelerometers for highly cost-driven applications in recording earthquake strong motion. We anticipate applications for such sensors in providing the lifeline and emergency-response communities with an immediate, comprehensive picture of the extent and characteristics of likely damage. We also foresee their use as 'filler' instruments sited between research-grade instruments to provide spatially detailed and near-field records of large earthquakes (on the order of 1000 stations at 600-m intervals in San Fernando Valley, population 1.2 million, for example). The latter applications would provide greatly improved attenuation relationships for building codes and design, the first examples of mainshock information (that is, potentially nonlinear regime) for microzonation, and a suite of records for structural engineers. We also foresee possible applications in monitoring structural inter-story drift during earthquakes, possibly leading to local and remote alarm functions as well as design criteria. This effort appears to be the first of its type at the USGS. It is spurred by rapid advances in sensor technology and the recognition of potential non-classical applications. In this report, we estimate sensor noise spectra, relative transfer functions and cross-axis sensitivity of six inexpensive sensors. We tested three micromachined ('silicon-chip') sensors in addition to classical force-balance and piezoelectric examples. This sample of devices is meant to be representative, not comprehensive. Sensor noise spectra were estimated by recording system output with the sensor mounted on a pneumatically supported 545-kg optical-bench isolation table. This isolation table appears to limit ground motion to below our system noise level. These noise estimates include noise introduced by signal-conditioning circuitry, the analog-to-digital converter (ADC), and noise induced in connecting wiring by ambient electromagnetic fields in our suburban laboratory. These latter sources are believed to dominate sensor noise in the quieter sensors we tested. Transfer functions were obtained relative to a research grade force-balance accelerometer (a Kinemetrics TM FBA-11) by shaking the sensors simultaneously on the same shake table and taking spectral ratios with the output of the FBA- 11. This reference sensor is said to have 120 db dynamic range (-+20 bits, though we only digitized it at 16 bits resolution and drove it with relatively small signals). We did not test temperature sensitivity, which is thought to be a significant issue at least for the silicon devices. Though these tests were not designed to be definitive (our anticipated applications do not demand research-grade precision), our tests do appear to have been successful in estimating relative transfer functions from about 0.3 to 50 Hz. Most sensors performed adequately in this range, with essentially fiat relative transfer functions. Noise tests appear to measure sensor noise well for the noisier (generally less expensive) instruments from about 0.1 to 50 Hz.

A neural model of hippocampal-striatal interactions in associative learning and transfer generalization in various neurological and psychiatric patients

PubMed Central

Moustafa, Ahmed A.; Keri, Szabolcs; Herzallah, Mohammad M.; Myers, Catherine E.; Gluck, Mark A.

2010-01-01

Building on our previous neurocomputational models of basal ganglia and hippocampal-region function (and their modulation by dopamine and acetylcholine, respectively), we show here how an integration of these models can inform our understanding of the interaction between the basal ganglia and hippocampal region in associative learning and transfer generalization across various patient populations. As a common test bed for exploring interactions between these brain regions and neuromodulators, we focus on the acquired equivalence task, an associative learning paradigm in which stimuli that have been associated with the same outcome acquire a functional similarity such that subsequent generalization between these stimuli increases. This task has been used to test cognitive dysfunction in various patient populations with damages to the hippocampal region and basal ganglia, including studies of patients with Parkinson’s disease (PD), schizophrenia, basal forebrain amnesia, and hippocampal atrophy. Simulation results show that damage to the hippocampal region—as in patients with hippocampal atrophy (HA), hypoxia, mild Alzheimer’s (AD), or schizophrenia—leads to intact associative learning but impaired transfer generalization performance. Moreover, the model demonstrates how PD and anterior communicating artery (ACoA) aneurysm—two very different brain disorders that affect different neural mechanisms—can have similar effects on acquired equivalence performance. In particular, the model shows that simulating a loss of dopamine function in the basal ganglia module (as in PD) leads to slow acquisition learning but intact transfer generalization. Similarly, the model shows that simulating the loss of acetylcholine in the hippocampal region (as in ACoA aneurysm) also results in slower acquisition learning. We argue from this that changes in associative learning of stimulus-action pathways (in the basal ganglia) or changes in the learning of stimulus representations (in the hippocampal region) can have similar functional effects. PMID:20728258

Degree of Handedness Affects Intermanual Transfer of Skill Learning

PubMed Central

Chase, Cori; Seidler, Rachael

2008-01-01

Intermanual transfer of skill learning has often been used as a paradigm to study functional specialization and hemispheric interactions in relation to handedness. This literature has not evaluated whether degree of handedness impacts learning and intermanual transfer. Because handedness scores are related to factors that might influence intermanual transfer, such as engagement of the ipsilateral hemisphere during movement and corpus callosum volume, we tested whether degree of handedness is correlated with transfer magnitude. We had groups of left and right handed participants perform a sensorimotor adaptation task and a sequence learning task. Following learning with either the dominant or nondominant hand, participants transferred to task performance with the other hand. We evaluated whether the magnitude of learning and intermanual transfer were influenced by either direction and / or degree of handedness. Participants exhibited faster sensorimotor adaptation with the right hand, regardless of whether they were right or left handed. In addition, less strongly left handed individuals exhibited better intermanual transfer of sensorimotor adaptation, while less strongly right handed individuals exhibited better intermanual transfer of sequence learning. The findings suggest that involvement of the ipsilateral hemisphere during learning may influence intermanual transfer magnitude. PMID:18592225

Functional Outcomes Following Anterior Transfer of the Tibialis Posterior Tendon for Foot Drop Secondary to Peroneal Nerve Palsy.

PubMed

Cho, Byung-Ki; Park, Kyoung-Jin; Choi, Seung-Myung; Im, Se-Hyuk; SooHoo, Nelson F

2017-06-01

This retrospective comparative study reports the practical function in daily and sports activities after tibialis posterior tendon transfer for foot drop secondary to peroneal nerve palsy. Seventeen patients were followed for a minimum of 3 years after tibialis posterior tendon transfer for foot drop secondary to peroneal nerve palsy. Matched controls were used to evaluate the level of functional restoration. Functional evaluations included American Orthopaedic Foot & Ankle Society (AOFAS) scores, Foot and Ankle Outcome Score (FAOS), Foot and Ankle Ability Measure (FAAM) scores, and isokinetic muscle strength test. Radiographic evaluation for the changes of postoperative foot alignment included Meary angle, calcaneal pitch angle, hindfoot alignment angle, and navicular height. Mean AOFAS, FAOS, and FAAM scores significantly improved from 65.1 to 86.2, 55.6 to 87.8, and 45.7 to 84.4 points at final follow-up, respectively. However, all functional evaluation scores were significantly lower as compared to the control group ( P < .001). Mean peak torque (60 degrees/sec) of ankle dorsiflexors, plantarflexors, invertors, and evertors at final follow-up were 7.1 (deficit ratio of 65.4%), 39.2, 9.8, and 7.3 Nm, respectively. These muscle strengths were significantly lower compared to the control group ( P < .001). No significant differences in radiographic measurements were found, and no patients presented with a postoperative flat foot deformity. One patient (5.9%) needed an ankle-foot orthosis for occupational activity. Anterior transfer of the tibialis posterior tendon appears to be an effective surgical option for paralytic foot drop secondary to peroneal nerve palsy. Although restoration of dorsiflexion strength postoperatively was about 33% of the normal ankle, function in daily activities and gait ability were satisfactorily improved. In addition, tibialis posterior tendon transfer demonstrated no definitive radiographic or clinical progression to postoperative flat foot deformity at intermediate-term follow-up. Level IV, retrospective case series.

Transfer function characteristics of super resolving systems

NASA Technical Reports Server (NTRS)

Milster, Tom D.; Curtis, Craig H.

1992-01-01

Signal quality in an optical storage device greatly depends on the optical system transfer function used to write and read data patterns. The problem is similar to analysis of scanning optical microscopes. Hopkins and Braat have analyzed write-once-read-many (WORM) optical data storage devices. Herein, transfer function analysis of magnetooptic (MO) data storage devices is discussed with respect to improving transfer-function characteristics. Several authors have described improving the transfer function as super resolution. However, none have thoroughly analyzed the MO optical system and effects of the medium. Both the optical system transfer function and effects of the medium of this development are discussed.

The (virtual) conceptual necessity of quantum probabilities in cognitive psychology.

PubMed

Blutner, Reinhard; beim Graben, Peter

2013-06-01

We propose a way in which Pothos & Busemeyer (P&B) could strengthen their position. Taking a dynamic stance, we consider cognitive tests as functions that transfer a given input state into the state after testing. Under very general conditions, it can be shown that testable properties in cognition form an orthomodular lattice. Gleason's theorem then yields the conceptual necessity of quantum probabilities (QP).

How Do Alternative Ways of Responding Influence 3- and 4-Year-Olds' Performance on Tests of Executive Function and Theory of Mind?

ERIC Educational Resources Information Center

Carroll, Daniel J.; Riggs, Kevin J.; Apperly, Ian A.; Graham, Kate; Geoghegan, Ceara

2012-01-01

A total of 69 preschool children were tested on measures of false belief understanding (the Unexpected Transfer task), inhibitory control (the Grass/Snow task), and strategic reasoning (the Windows task). For each task, children indicated their response either by pointing with their index finger or by using a nonstandard response mode (pointing…

Examination of swallowing maneuver training and transfer of practiced behaviors to laryngeal vestibule kinematics in functional swallowing of healthy adults

PubMed Central

Guedes, Renata; Azola, Alba; Macrae, Phoebe; Sunday, Kirstyn; Mejia, Veerley; Vose, Alicia; Humbert, Ianessa A.

2017-01-01

Swallowing maneuvers are routinely trained in dysphagia rehabilitation with the assumption that practiced behaviors transfer to functional swallowing, however transfer is rarely examined in the deglutition literature. The goal of this study was to train the volitional laryngeal vestibule closure (vLVC) maneuver, which is a swallowing maneuver that targets prolonged laryngeal vestibule closure (LVC). In two different training experiments, 69 healthy adults underwent Long-hold (hold vLVC as long as possible) or Short-hold vLVC training (hold vLVC for 2 seconds). Before and after vLVC training, natural swallows (swallowing without a therapeutic technique) were completed. The outcome variables included laryngeal vestibule closure reaction time and the duration of laryngeal vestibule closure. Results indicate that during both Long-hold and Short-hold vLVC trainings, vLVC swallows had faster laryngeal vestibule closure reaction times and longer durations of laryngeal vestibule closure than in pre-training 5ml liquid swallows. However, only faster laryngeal vestibule closure reaction times transferred to post-training 5ml liquid swallows (20–24% faster), but not prolonged durations of laryngeal vestibule closure. Our findings suggest that swallowing maneuver training has the potential to induce transfer of what was practiced to functional swallowing behavior, although not all practiced behaviors may generalize. These findings are significant for bolstering the effectiveness of dysphagia management medical settings and should be tested in individuals with dysphagia. PMID:28322908

Examination of swallowing maneuver training and transfer of practiced behaviors to laryngeal vestibule kinematics in functional swallowing of healthy adults.

PubMed

Guedes, Renata; Azola, Alba; Macrae, Phoebe; Sunday, Kirstyn; Mejia, Veerley; Vose, Alicia; Humbert, Ianessa A

2017-05-15

Swallowing maneuvers are routinely trained in dysphagia rehabilitation with the assumption that practiced behaviors transfer to functional swallowing, however transfer is rarely examined in the deglutition literature. The goal of this study was to train the volitional laryngeal vestibule closure (vLVC) maneuver, which is a swallowing maneuver that targets prolonged laryngeal vestibule closure (LVC). In two different training experiments, 69 healthy adults underwent Long-hold (hold vLVC as long as possible) or Short-hold vLVC training (hold vLVC for 2s). Before and after vLVC training, natural swallows (swallowing without a therapeutic technique) were completed. The outcome variables included laryngeal vestibule closure reaction time and the duration of laryngeal vestibule closure. Results indicate that during both Long-hold and Short-hold vLVC trainings, vLVC swallows had faster laryngeal vestibule closure reaction times and longer durations of laryngeal vestibule closure than in pre-training 5ml liquid swallows. However, only faster laryngeal vestibule closure reaction times transferred to post-training 5ml liquid swallows (20-24% faster), but not prolonged durations of laryngeal vestibule closure. Our findings suggest that swallowing maneuver training has the potential to induce transfer of what was practiced to functional swallowing behavior, although not all practiced behaviors may generalize. These findings are significant for bolstering the effectiveness of dysphagia management in medical settings and should be tested in individuals with dysphagia. Copyright © 2017 Elsevier Inc. All rights reserved.

Rational function representation of flap noise spectra including correction for reflection effects. [acoustic properties of engine exhaust jets deflected for externally blown flaps

NASA Technical Reports Server (NTRS)

Miles, J. H.

1974-01-01

A rational function is presented for the acoustic spectra generated by deflection of engine exhaust jets for under-the-wing and over-the-wing versions of externally blown flaps. The functional representation is intended to provide a means for compact storage of data and for data analysis. The expressions are based on Fourier transform functions for the Strouhal normalized pressure spectral density, and on a correction for reflection effects based on the N-independent-source model of P. Thomas extended by use of a reflected ray transfer function. Curve fit comparisons are presented for blown flap data taken from turbofan engine tests and from large scale cold-flow model tests. Application of the rational function to scrubbing noise theory is also indicated.

Targeting latent function: Encouraging effective encoding for successful memory training and transfer

PubMed Central

Lustig, Cindy; Flegal, Kristin E.

2009-01-01

Cognitive training programs for older adults often result in improvements at the group level. However, there are typically large age and individual differences in the size of training benefits. These differences may be related to the degree to which participants implement the processes targeted by the training program. To test this possibility, we tested older adults in a memory-training procedure either under specific strategy instructions designed to encourage semantic, integrative encoding, or in a condition that encouraged time and attention to encoding but allowed participants to choose their own strategy. Both conditions improved the performance of old-old adults relative to an earlier study (Bissig & Lustig, 2007) and reduced self-reports of everyday memory errors. Performance in the strategy-instruction group was related to pre-existing ability, performance in the strategy-choice group was not. The strategy-choice group performed better on a laboratory transfer test of recognition memory, and training performance was correlated with reduced everyday memory errors. Training programs that target latent but inefficiently-used abilities while allowing flexibility in bringing those abilities to bear may best promote effective training and transfer. PMID:19140647

Validation of the MEPDG transfer functions using the LTPP test sections in Georgia task 2 interim report.

DOT National Transportation Integrated Search

2013-07-16

The Georgia Department of Transportation (GDOT) is transitioning from empirical design procedures to the MEPDG : procedure for designing new and rehabilitated highway pavements. GDOT currently uses the 1972 AASHTO Interim : Guide for Design of Paveme...

Function Transfer in Human Operant Experiments: The Role of Stimulus Pairings

ERIC Educational Resources Information Center

Tonneau, Francois; Gonzalez, Carmen

2004-01-01

Although function transfer often has been studied in complex operant procedures (such as matching to sample), whether operant reinforcement actually produces function transfer in such settings has not been established. The present experiments, with high school students as subjects, suggest that stimulus pairings can promote function transfer in…

Cerebellar activation during motor sequence learning is associated with subsequent transfer to new sequences.

PubMed

Shimizu, Renee E; Wu, Allan D; Knowlton, Barbara J

2016-12-01

Effective learning results not only in improved performance on a practiced task, but also in the ability to transfer the acquired knowledge to novel, similar tasks. Using a modified serial reaction time (RT) task, the authors examined the ability to transfer to novel sequences after practicing sequences in a repetitive order versus a nonrepeating interleaved order. Interleaved practice resulted in better performance on new sequences than repetitive practice. In a second study, participants practiced interleaved sequences in a functional MRI (fMRI) scanner and received a transfer test of novel sequences. Transfer ability was positively correlated with cerebellar blood oxygen level dependent activity during practice, indicating that greater cerebellar engagement during training resulted in better subsequent transfer performance. Interleaved practice may thus result in a more generalized representation that is robust to interference, and the degree of activation in the cerebellum may be a reflection of the instantiation and engagement of internal models. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Spectral Analysis and Experimental Modeling of Ice Accretion Roughness

NASA Technical Reports Server (NTRS)

Orr, D. J.; Breuer, K. S.; Torres, B. E.; Hansman, R. J., Jr.

1996-01-01

A self-consistent scheme for relating wind tunnel ice accretion roughness to the resulting enhancement of heat transfer is described. First, a spectral technique of quantitative analysis of early ice roughness images is reviewed. The image processing scheme uses a spectral estimation technique (SET) which extracts physically descriptive parameters by comparing scan lines from the experimentally-obtained accretion images to a prescribed test function. Analysis using this technique for both streamwise and spanwise directions of data from the NASA Lewis Icing Research Tunnel (IRT) are presented. An experimental technique is then presented for constructing physical roughness models suitable for wind tunnel testing that match the SET parameters extracted from the IRT images. The icing castings and modeled roughness are tested for enhancement of boundary layer heat transfer using infrared techniques in a "dry" wind tunnel.

A randomized controlled trial of an activity specific exercise program for individuals with Alzheimer disease in long-term care settings.

PubMed

Roach, Kathryn E; Tappen, Ruth M; Kirk-Sanchez, Neva; Williams, Christine L; Loewenstein, David

2011-01-01

To determine whether an activity specific exercise program could improve ability to perform basic mobility activities in long-term care residents with Alzheimer disease (AD). Randomized, controlled, single-blinded clinical trial. Residents of 7 long-term care facilities. Eighty-two long-term care residents with mild to severe AD. An activity specific exercise program was compared to a walking program and to an attention control. Ability to perform bed mobility and transfers was assessed using the subscales of the Acute Care Index of Function; functional mobility was measured using the 6-Minute Walk test. Subjects receiving the activity specific exercise program improved in ability to perform transfers, whereas subjects in the other 2 groups declined.

Auditory temporal perceptual learning and transfer in Chinese-speaking children with developmental dyslexia.

PubMed

Zhang, Manli; Xie, Weiyi; Xu, Yanzhi; Meng, Xiangzhi

2018-03-01

Perceptual learning refers to the improvement of perceptual performance as a function of training. Recent studies found that auditory perceptual learning may improve phonological skills in individuals with developmental dyslexia in alphabetic writing system. However, whether auditory perceptual learning could also benefit the reading skills of those learning the Chinese logographic writing system is, as yet, unknown. The current study aimed to investigate the remediation effect of auditory temporal perceptual learning on Mandarin-speaking school children with developmental dyslexia. Thirty children with dyslexia were screened from a large pool of students in 3th-5th grades. They completed a series of pretests and then were assigned to either a non-training control group or a training group. The training group worked on a pure tone duration discrimination task for 7 sessions over 2 weeks with thirty minutes per session. Post-tests immediately after training and a follow-up test 2 months later were conducted. Analyses revealed a significant training effect in the training group relative to non-training group, as well as near transfer to the temporal interval discrimination task and far transfer to phonological awareness, character recognition and reading fluency. Importantly, the training effect and all the transfer effects were stable at the 2-month follow-up session. Further analyses found that a significant correlation between character recognition performance and learning rate mainly existed in the slow learning phase, the consolidation stage of perceptual learning, and this effect was modulated by an individuals' executive function. These findings indicate that adaptive auditory temporal perceptual learning can lead to learning and transfer effects on reading performance, and shed further light on the potential role of basic perceptual learning in the remediation and prevention of developmental dyslexia. Copyright © 2018 Elsevier Ltd. All rights reserved.

ωB97M-V: A combinatorially optimized, range-separated hybrid, meta-GGA density functional with VV10 nonlocal correlation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mardirossian, Narbe; Head-Gordon, Martin

2016-06-07

A combinatorially optimized, range-separated hybrid, meta-GGA density functional with VV10 nonlocal correlation is presented in this paper. The final 12-parameter functional form is selected from approximately 10 × 10 9 candidate fits that are trained on a training set of 870 data points and tested on a primary test set of 2964 data points. The resulting density functional, ωB97M-V, is further tested for transferability on a secondary test set of 1152 data points. For comparison, ωB97M-V is benchmarked against 11 leading density functionals including M06-2X, ωB97X-D, M08-HX, M11, ωM05-D, ωB97X-V, and MN15. Encouragingly, the overall performance of ωB97M-V on nearlymore » 5000 data points clearly surpasses that of all of the tested density functionals. Finally, in order to facilitate the use of ωB97M-V, its basis set dependence and integration grid sensitivity are thoroughly assessed, and recommendations that take into account both efficiency and accuracy are provided.« less

Body weight supported treadmill training versus traditional training in patients dependent on walking assistance after stroke: a randomized controlled trial.

PubMed

Høyer, Ellen; Jahnsen, Reidun; Stanghelle, Johan Kvalvik; Strand, Liv Inger

2012-01-01

Treadmill training with body weight support (TTBWS) for relearning walking ability after brain damage is an approach under current investigation. Efficiency of this method beyond traditional training is lacking evidence, especially in patients needing walking assistance after stroke. The objective of this study was to investigate change in walking and transfer abilities, comparing TTBWS with traditional walking training. A single-blinded, randomized controlled trial was conducted. Sixty patients referred for multi-disciplinary primary rehabilitation were assigned into one of two intervention groups, one received 30 sessions of TTBWS plus traditional training, the other traditional training alone. Daily training was 1 hr. Outcome measures were Functional Ambulation Categories (FAC), Walking, Functional Independence Measure (FIM); shorter transfer and stairs, 10 m and 6-min walk tests. Substantial improvements in walking and transfer were shown within both groups after 5 and 11 weeks of intervention. Overall no statistical significant differences were found between the groups, but 12 of 17 physical measures tended to show improvements in favour of the treadmill approach. Both training strategies provided significant improvements in the tested activities, suggesting that similar outcomes can be obtained in the two modalities by systematic, intensive and goal directed training.

Validation of the plain chest radiograph for epidemiologic studies of airflow obstruction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musk, A.W.

The chest radiographs of 125 industrial workers from rural New South Wales were examined for overinflated lungs, with and without attenuated midzonal vessels. Although the mean values of a comprehensive range of pulmonary function tests in the whole group were within normal limits, the nine subjects whose radiographs showed overinflated lungs and attenuated vessels had significantly impaired pulmonary function in comparison with 85 subjects with normal radiographs. The mean values for these nine subjects, expressed as a percentage of the mean value for subjects with normal radiographs, were: forced expiratory volume in 1 second, 75%; total lung capacity, 107%; residualmore » volume, 143%; transpulmonary pressure at maximum inspiration, 60%; static deflation compliance, 158%; lung volume at transpulmonary pressure 10 cm H/sub 2/O, 132%; transfer factor, 79%; and transfer factor/alveolar volume, 77%. Similar results were obtained by a second observer. Those subjects with overinflation but no vascular attenuation had significantly larger mean values for vital capacity and alveolar volume but no significant difference in total lung capacity or other tests of the mechanical properties of the lungs. Agreement on the presence of a positive sign between the two observers expressed as a percentage of those considered positive by either was 81% for overinflation and 62% for attenuated midzonal vessels. The results indicate that in groups of subjects with normal-average values of pulmonary function, the plain chest radiograph may provide information concerning pulmonary structure that is reflected in tests of function.« less

Production Maintenance Infrastructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jason Gabler, David Skinner

2005-11-01

PMI is a XML framework for formulating tests of software and software environments which operate in a relatively push button manner, i.e., can be automated, and that provide results that are readily consumable/publishable via RSS. Insofar as possible the tests are carried out in manner congruent with real usage. PMI drives shell scripts via a perl program which is charge of timing, validating each test, and controlling the flow through sets of tests. Testing in PMI is built up hierarchically. A suite of tests may start by testing basic functionalities (file system is writable, compiler is found and functions, shellmore » environment behaves as expected, etc.) and work up to large more complicated activities (execution of parallel code, file transfers, etc.) At each step in this hierarchy a failure leads to generation of a text message or RSS that can be tagged as to who should be notified of the failure. There are two functionalities that PMI has been directed at. 1) regular and automated testing of multi user environments and 2) version-wise testing of new software releases prior to their deployment in a production mode.« less

First-and Second-Order Displacement Transfer Functions for Structural Shape Calculations Using Analytically Predicted Surface Strains

NASA Technical Reports Server (NTRS)

Ko, William L.; Fleischer, Van Tran

2012-01-01

New first- and second-order displacement transfer functions have been developed for deformed shape calculations of nonuniform cross-sectional beam structures such as aircraft wings. The displacement transfer functions are expressed explicitly in terms of beam geometrical parameters and surface strains (uniaxial bending strains) obtained at equally spaced strain stations along the surface of the beam structure. By inputting the measured or analytically calculated surface strains into the displacement transfer functions, one could calculate local slopes, deflections, and cross-sectional twist angles of the nonuniform beam structure for mapping the overall structural deformed shapes for visual display. The accuracy of deformed shape calculations by the first- and second-order displacement transfer functions are determined by comparing these values to the analytically predicted values obtained from finite element analyses. This comparison shows that the new displacement transfer functions could quite accurately calculate the deformed shapes of tapered cantilever tubular beams with different tapered angles. The accuracy of the present displacement transfer functions also are compared to those of the previously developed displacement transfer functions.

Transfer of learning between unimanual and bimanual rhythmic movement coordination: transfer is a function of the task dynamic.

PubMed

Snapp-Childs, Winona; Wilson, Andrew D; Bingham, Geoffrey P

2015-07-01

Under certain conditions, learning can transfer from a trained task to an untrained version of that same task. However, it is as yet unclear what those certain conditions are or why learning transfers when it does. Coordinated rhythmic movement is a valuable model system for investigating transfer because we have a model of the underlying task dynamic that includes perceptual coupling between the limbs being coordinated. The model predicts that (1) coordinated rhythmic movements, both bimanual and unimanual, are organised with respect to relative motion information for relative phase in the coupling function, (2) unimanual is less stable than bimanual coordination because the coupling is unidirectional rather than bidirectional, and (3) learning a new coordination is primarily about learning to perceive and use the relevant information which, with equal perceptual improvement due to training, yields equal transfer of learning from bimanual to unimanual coordination and vice versa [but, given prediction (2), the resulting performance is also conditioned by the intrinsic stability of each task]. In the present study, two groups were trained to produce 90° either unimanually or bimanually, respectively, and tested in respect to learning (namely improved performance in the trained 90° coordination task and improved visual discrimination of 90°) and transfer of learning (to the other, untrained 90° coordination task). Both groups improved in the task condition in which they were trained and in their ability to visually discriminate 90°, and this learning transferred to the untrained condition. When scaled by the relative intrinsic stability of each task, transfer levels were found to be equal. The results are discussed in the context of the perception-action approach to learning and performance.

Nonparametric Transfer Function Models

PubMed Central

Liu, Jun M.; Chen, Rong; Yao, Qiwei

2009-01-01

In this paper a class of nonparametric transfer function models is proposed to model nonlinear relationships between ‘input’ and ‘output’ time series. The transfer function is smooth with unknown functional forms, and the noise is assumed to be a stationary autoregressive-moving average (ARMA) process. The nonparametric transfer function is estimated jointly with the ARMA parameters. By modeling the correlation in the noise, the transfer function can be estimated more efficiently. The parsimonious ARMA structure improves the estimation efficiency in finite samples. The asymptotic properties of the estimators are investigated. The finite-sample properties are illustrated through simulations and one empirical example. PMID:20628584

Self-interaction effects on charge-transfer collisions

DOE PAGES

Quashie, Edwin E.; Saha, Bidhan C.; Andrade, Xavier; ...

2017-04-27

In this article, we investigate the role of the self-interaction error in the simulation of collisions using time-dependent density functional theory (TDDFT) and Ehrenfest dynamics. In addition, we compare many different approximations of the exchange and correlation potential, using as a test system the collision of H + + CH 4 at 30 eV. We find that semilocal approximations, like the Perdew-Burke- Ernzerhof (PBE), and even hybrid functionals, such as the Becke, 3-parameter, Lee-Yang-Parr (B3LYP), produce qualitatively incorrect predictions for the scattering of the proton. This discrepancy appears because the self-interaction error allows the electrons to jump too easily tomore » the proton, leading to radically different forces with respect to the non-self-interacting case. Lastly, from our results, we conclude that using a functional that is self-interaction free is essential to properly describing charge-transfer collisions between ions and molecules in TDDFT.« less

Off-Axis Nulling Transfer Function Measurement: A First Assessment

NASA Technical Reports Server (NTRS)

Vedova, G. Dalla; Menut, J.-L.; Millour, F.; Petrov, R.; Cassaing, F.; Danchi, W. C.; Jacquinod, S.; Lhome, E.; Lopez, B.; Lozi, J.;

Artificial neural network and classical least-squares methods for neurotransmitter mixture analysis.

PubMed

Schulze, H G; Greek, L S; Gorzalka, B B; Bree, A V; Blades, M W; Turner, R F

1995-02-01

Identification of individual components in biological mixtures can be a difficult problem regardless of the analytical method employed. In this work, Raman spectroscopy was chosen as a prototype analytical method due to its inherent versatility and applicability to aqueous media, making it useful for the study of biological samples. Artificial neural networks (ANNs) and the classical least-squares (CLS) method were used to identify and quantify the Raman spectra of the small-molecule neurotransmitters and mixtures of such molecules. The transfer functions used by a network, as well as the architecture of a network, played an important role in the ability of the network to identify the Raman spectra of individual neurotransmitters and the Raman spectra of neurotransmitter mixtures. Specifically, networks using sigmoid and hyperbolic tangent transfer functions generalized better from the mixtures in the training data set to those in the testing data sets than networks using sine functions. Networks with connections that permit the local processing of inputs generally performed better than other networks on all the testing data sets. and better than the CLS method of curve fitting, on novel spectra of some neurotransmitters. The CLS method was found to perform well on noisy, shifted, and difference spectra.

International Space Station Alpha's bearing, motor, and roll ring module developmental testing and results

NASA Technical Reports Server (NTRS)

Obrien, David L.

1994-01-01

This paper presents the design and developmental testing associated with the bearing, motor, and roll ring module (BMRRM) used for the beta rotation axis on International Space Station Alpha (ISSA). The BMRRM with its controllers located in the electronic control unit (ECU), provides for the solar array pointing and tracking functions as well as power and signal transfer across a rotating interface.

Proceedings of the Symposium of Medical (Ophthalmic) Surveillance of Personnel Potentially Exposed to Laser Radiation Held on 8-9 September 1982.

DTIC Science & Technology

1982-01-01

Hardy, Rand, and Rittler (HRR) pseudoisochromatic plates and the Farnsworth D15 color panel; these tests were normal. However, in an anomaloscopic...measures (e.g., slit-lamp and ophthalmoscopic examinations ) rather than quantitative visual function tests (e.g., Snellen acuity, contrast transfer, color...arose from eye examination programs ii ..’ 1C- following field tests at Fort Hunter Liggett, California and at Yuma Proving Ground, Arizona. Most, if

Closed-loop spontaneous baroreflex transfer function is inappropriate for system identification of neural arc but partly accurate for peripheral arc: predictability analysis

PubMed Central

Kamiya, Atsunori; Kawada, Toru; Shimizu, Shuji; Sugimachi, Masaru

2011-01-01

Abstract Although the dynamic characteristics of the baroreflex system have been described by baroreflex transfer functions obtained from open-loop analysis, the predictability of time-series output dynamics from input signals, which should confirm the accuracy of system identification, remains to be elucidated. Moreover, despite theoretical concerns over closed-loop system identification, the accuracy and the predictability of the closed-loop spontaneous baroreflex transfer function have not been evaluated compared with the open-loop transfer function. Using urethane and α-chloralose anaesthetized, vagotomized and aortic-denervated rabbits (n = 10), we identified open-loop baroreflex transfer functions by recording renal sympathetic nerve activity (SNA) while varying the vascularly isolated intracarotid sinus pressure (CSP) according to a binary random (white-noise) sequence (operating pressure ± 20 mmHg), and using a simplified equation to calculate closed-loop-spontaneous baroreflex transfer function while matching CSP with systemic arterial pressure (AP). Our results showed that the open-loop baroreflex transfer functions for the neural and peripheral arcs predicted the time-series SNA and AP outputs from measured CSP and SNA inputs, with r2 of 0.8 ± 0.1 and 0.8 ± 0.1, respectively. In contrast, the closed-loop-spontaneous baroreflex transfer function for the neural arc was markedly different from the open-loop transfer function (enhanced gain increase and a phase lead), and did not predict the time-series SNA dynamics (r2; 0.1 ± 0.1). However, the closed-loop-spontaneous baroreflex transfer function of the peripheral arc partially matched the open-loop transfer function in gain and phase functions, and had limited but reasonable predictability of the time-series AP dynamics (r2, 0.7 ± 0.1). A numerical simulation suggested that a noise predominantly in the neural arc under resting conditions might be a possible mechanism responsible for our findings. Furthermore, the predictabilities of the neural arc transfer functions obtained in open-loop and closed-loop conditions were validated by closed-loop pharmacological (phenylephrine and nitroprusside infusions) pressure interventions. Time-series SNA responses to drug-induced AP changes predicted by the open-loop transfer function matched closely the measured responses (r2, 0.9 ± 0.1), whereas SNA responses predicted by closed-loop-spontaneous transfer function deviated greatly and were the inverse of measured responses (r, −0.8 ± 0.2). These results indicate that although the spontaneous baroreflex transfer function obtained by closed-loop analysis has been believed to represent the neural arc function, it is inappropriate for system identification of the neural arc but is essentially appropriate for the peripheral arc under resting conditions, when compared with open-loop analysis. PMID:21486839

The Anatomy of Action Systems: Task Differentiation When Learning an EMG Controlled Game

PubMed Central

van Dijk, Ludger; Heerschop, Anniek; van der Sluis, Corry K.; Bongers, Raoul M.

2016-01-01

This study aims to determine to what extent the task for an action system in its initial development relies on functional and anatomical components. Fifty-two able-bodied participants were randomly assigned to one of three experimental groups or to a control group. As a pre- and post-test all groups performed a computer game with the same goal and using the same musculature. One experimental group also trained to perform this test, while the other two experimental groups learned to perform a game that differed either in its goal or in the musculature used. The observed change in accuracy indicated that retaining the goal of the task or the musculature used equally increased transfer performance relative to controls. Conversely, changing either the goal or the musculature equally decreased transfer relative to training the test. These results suggest that in the initial development of an action system, the task to which the system pertains is not specified solely by either the goal of the task or the anatomical structures involved. It is suggested that functional specificity and anatomical dependence might equally be outcomes of continuously differentiating activity. PMID:28018278

Validation Tests of Fiber Optic Strain-Based Operational Shape and Load Measurements

NASA Technical Reports Server (NTRS)

Bakalyar, John A.; Jutte, Christine

2012-01-01

Aircraft design has been progressing toward reduced structural weight to improve fuel efficiency, increase performance, and reduce cost. Lightweight aircraft structures are more flexible than conventional designs and require new design considerations. Intelligent sensing allows for enhanced control and monitoring of aircraft, which enables increased structurally efficiency. The NASA Dryden Flight Research Center (DFRC) has developed an instrumentation system and analysis techniques that combine to make distributed structural measurements practical for lightweight vehicles. Dryden's Fiber Optic Strain Sensing (FOSS) technology enables a multitude of lightweight, distributed surface strain measurements. The analysis techniques, referred to as the Displacement Transfer Functions (DTF) and Load Transfer Functions (LTF), use surface strain values to calculate structural deflections and operational loads. The combined system is useful for real-time monitoring of aeroelastic structures, along with many other applications. This paper describes how the capabilities of the measurement system were demonstrated using subscale test articles that represent simple aircraft structures. Empirical FOSS strain data were used within the DTF to calculate the displacement of the article and within the LTF to calculate bending moments due to loads acting on the article. The results of the tests, accuracy of the measurements, and a sensitivity analysis are presented.

Dynamic characteristics of the thorax connected with the heart action.

PubMed

Juznic, G; Emri, I; Peterec, D; Prepadnik, M

1979-01-01

We determined the indices of local vibrations (resonance frequency, damping coefficient, stiffness constant, extinction time) and transfer function H(s) . 10(-6) for three somatotypes and three respiratory positions on 88 points of the thorax. The examinees were males (age 21 years). We found the resonance frequencies of 36.86--54.75 cps, damping coefficient (delta) 0.121--0.217. This means the damping is less than critical (delta = 1). We applied shocks (a force of 2 N) with a reflex hammer on 88 points of the thorax. The force diminished from the exciting place (say ictus) to the recording place (accelerometer on the sternum) from 2 to 0.2 N. The athletic type has the highest resonance frequency and stiffness constant; the leptosomic type has the highest damping; the longest extinction time belongs to the pyknic type. The pyknic type has also the highest value of the transfer function. The respiratory position (quiet respiration, Valsalva and Müller experiment) influences the values of the indices of local vibrations and of the transfer function. The influence is evident especially on the intercostal points: the transfer of the oscillations is alleviated at a higher stiffness of the thorax (Valsalva; the value of H(S) . 10(-6) rises from 7.00 to 9.39 sec2), it deteriorates at a small stiffness of the thorax (in Müller's experiment falls to 2.78 sec2). With the fall in the intrathoracic pressure the damping in the intercostal points decreases. On the basis of experiments the conclusion was made that a short testing of the thorax of an examinee will give the dynamic characteristics of the thorax (indices of local vibrations and transfer functions) of the individual. This procedure will alleviate the quantitative use of noninvasive mechanical methods in the assessment of the cardiovascular function.

Work function determination of promising electrode materials for thermionic energy converters

NASA Technical Reports Server (NTRS)

Jacobson, D.; Storms, E.; Skaggs, B.; Kouts, T.; Jaskie, J.; Manda, M.

1976-01-01

The work function determinations of candidate materials for low temperature (1400 K) thermionics through vacuum emission tests are discussed. Two systems, a vacuum emission test vehicle and a thermionic emission microscope are used for emission measurements. Some nickel and cobalt based super alloys were preliminarily examined. High temperature physical properties and corrosion behavior of some super alloy candidates are presented. The corrosion behavior of sodium is of particular interest since topping cycles might use sodium heat transfer loops. A Marchuk tube was designed for plasma discharge studies with the carbide and possibly some super alloy samples. A series of metal carbides and other alloys were fabricated and tested in a special high temperature mass spectrometer. This information coupled with work function determinations was evaluated in an attempt to learn how electron bonding occurs in transition alloys.

Calibration of the modulation transfer function of surface profilometers with binary pseudo-random test standards: Expanding the application range

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yashchuk, Valeriy V; Anderson, Erik H.; Barber, Samuel K.

2010-07-26

A modulation transfer function (MTF) calibration method based on binary pseudo-random (BPR) gratings and arrays [Proc. SPIE 7077-7 (2007), Opt. Eng. 47(7), 073602-1-5 (2008)] has been proven to be an effective MTF calibration method for a number of interferometric microscopes and a scatterometer [Nucl. Instr. and Meth. A 616, 172-82 (2010]. Here we report on a significant expansion of the application range of the method. We describe the MTF calibration of a 6 inch phase shifting Fizeau interferometer. Beyond providing a direct measurement of the interferometer's MTF, tests with a BPR array surface have revealed an asymmetry in the instrument'smore » data processing algorithm that fundamentally limits its bandwidth. Moreover, the tests have illustrated the effects of the instrument's detrending and filtering procedures on power spectral density measurements. The details of the development of a BPR test sample suitable for calibration of scanning and transmission electron microscopes are also presented. Such a test sample is realized as a multilayer structure with the layer thicknesses of two materials corresponding to BPR sequence. The investigations confirm the universal character of the method that makes it applicable to a large variety of metrology instrumentation with spatial wavelength bandwidths from a few nanometers to hundreds of millimeters.« less

Breakdown of local information processing may underlie isoflurane anesthesia effects.

PubMed

Wollstadt, Patricia; Sellers, Kristin K; Rudelt, Lucas; Priesemann, Viola; Hutt, Axel; Fröhlich, Flavio; Wibral, Michael

2017-06-01

The disruption of coupling between brain areas has been suggested as the mechanism underlying loss of consciousness in anesthesia. This hypothesis has been tested previously by measuring the information transfer between brain areas, and by taking reduced information transfer as a proxy for decoupling. Yet, information transfer is a function of the amount of information available in the information source-such that transfer decreases even for unchanged coupling when less source information is available. Therefore, we reconsidered past interpretations of reduced information transfer as a sign of decoupling, and asked whether impaired local information processing leads to a loss of information transfer. An important prediction of this alternative hypothesis is that changes in locally available information (signal entropy) should be at least as pronounced as changes in information transfer. We tested this prediction by recording local field potentials in two ferrets after administration of isoflurane in concentrations of 0.0%, 0.5%, and 1.0%. We found strong decreases in the source entropy under isoflurane in area V1 and the prefrontal cortex (PFC)-as predicted by our alternative hypothesis. The decrease in source entropy was stronger in PFC compared to V1. Information transfer between V1 and PFC was reduced bidirectionally, but with a stronger decrease from PFC to V1. This links the stronger decrease in information transfer to the stronger decrease in source entropy-suggesting reduced source entropy reduces information transfer. This conclusion fits the observation that the synaptic targets of isoflurane are located in local cortical circuits rather than on the synapses formed by interareal axonal projections. Thus, changes in information transfer under isoflurane seem to be a consequence of changes in local processing more than of decoupling between brain areas. We suggest that source entropy changes must be considered whenever interpreting changes in information transfer as decoupling.

Breakdown of local information processing may underlie isoflurane anesthesia effects

PubMed Central

Sellers, Kristin K.; Priesemann, Viola; Hutt, Axel

2017-01-01

The disruption of coupling between brain areas has been suggested as the mechanism underlying loss of consciousness in anesthesia. This hypothesis has been tested previously by measuring the information transfer between brain areas, and by taking reduced information transfer as a proxy for decoupling. Yet, information transfer is a function of the amount of information available in the information source—such that transfer decreases even for unchanged coupling when less source information is available. Therefore, we reconsidered past interpretations of reduced information transfer as a sign of decoupling, and asked whether impaired local information processing leads to a loss of information transfer. An important prediction of this alternative hypothesis is that changes in locally available information (signal entropy) should be at least as pronounced as changes in information transfer. We tested this prediction by recording local field potentials in two ferrets after administration of isoflurane in concentrations of 0.0%, 0.5%, and 1.0%. We found strong decreases in the source entropy under isoflurane in area V1 and the prefrontal cortex (PFC)—as predicted by our alternative hypothesis. The decrease in source entropy was stronger in PFC compared to V1. Information transfer between V1 and PFC was reduced bidirectionally, but with a stronger decrease from PFC to V1. This links the stronger decrease in information transfer to the stronger decrease in source entropy—suggesting reduced source entropy reduces information transfer. This conclusion fits the observation that the synaptic targets of isoflurane are located in local cortical circuits rather than on the synapses formed by interareal axonal projections. Thus, changes in information transfer under isoflurane seem to be a consequence of changes in local processing more than of decoupling between brain areas. We suggest that source entropy changes must be considered whenever interpreting changes in information transfer as decoupling. PMID:28570661

Within-Site Variation in Feather Stable Hydrogen Isotope (δ2Hf) Values of Boreal Songbirds: Implications for Assignment to Molt Origin.

PubMed

Nordell, Cameron J; Haché, Samuel; Bayne, Erin M; Sólymos, Péter; Foster, Kenneth R; Godwin, Christine M; Krikun, Richard; Pyle, Peter; Hobson, Keith A

2016-01-01

Understanding bird migration and dispersal is important to inform full life-cycle conservation planning. Stable hydrogen isotope ratios from feathers (δ2Hf) can be linked to amount-weighted long-term, growing season precipitation δ2H (δ2Hp) surfaces to create δ2Hf isoscapes for assignment to molt origin. However, transfer functions linking δ2Hp with δ2Hf are influenced by physiological and environmental processes. A better understanding of the causes and consequences of variation in δ2Hf values among individuals and species will improve the predictive ability of geographic assignment tests. We tested for effects of species, land cover, forage substrate, nest substrate, diet composition, body mass, sex, and phylogenetic relatedness on δ2Hf from individuals at least two years old of 21 songbird species captured during the same breeding season at a site in northeastern Alberta, Canada. For four species, we also tested for a year × species interaction effect on δ2Hf. A model including species as single predictor received the most support (AIC weight = 0.74) in explaining variation in δ2Hf. A species-specific variance parameter was part of all best-ranked models, suggesting variation in δ2Hf was not consistent among species. The second best-ranked model included a forage substrate × diet interaction term (AIC weight = 0.16). There was a significant year × species interaction effect on δ2Hf suggesting that interspecific differences in δ2Hf can differ among years. Our results suggest that within- and among-year interspecific variation in δ2Hf is the most important source of variance typically not being explicitly quantified in geographic assignment tests using non-specific transfer functions to convert δ2Hp into δ2Hf. However, this source of variation is consistent with the range of variation from the transfer functions most commonly being propagated in assignment tests of geographic origins for passerines breeding in North America.

The transfer of skills from cognitive and physical training to activities of daily living: a randomised controlled study.

PubMed

Hagovska, Magdalena; Nagyova, Iveta

2017-06-01

Ageing is associated with the deterioration of all cognitive functions, including attention, memory and psychomotor speed. It has not yet been clearly confirmed whether the effects of cognitive and physical interventions can improve activities of daily living (ADL). This study compared the effectiveness of cognitive and physical training on cognitive functions and the transfer to ADL. Eighty older people with mild cognitive impairment (mean age 67.07 ± 4.3 years) were randomly divided into an experimental group ( n  = 40) and a control group ( n  = 40). Data were collected in an outpatient psychiatric clinic in a randomised controlled trial. Primary outcome measures included the following: cognitive functions were evaluated using the mini mental state examination, the AVLT-Auditory verbal learning test, the Stroop test, the TMT-trail making test, the DRT-disjunctive reaction time and the NHPT-nine hole peg test. Secondary outcome measure was the Bristol activities of daily living scale. The experimental group underwent a CogniPlus and physical training; consisting of 20 training sessions over 10 weeks. Both groups went through 30 min of daily physical training for 10 weeks. After the training, significant differences in favour of the experimental group were found in almost all the tests. In memory (AVLT) (p ≤ 0.0001, effect size (ES) η 2  = 0.218. In reduction of the response time on attention tasks (Stroop tasks) ( p  ≤ 0.006, ES = 0.092-0.115). In lower error rates in all tests: Stroop tasks, DRT, TMT, NHPT ( p  ≤ 0.02-0.001, ES = 0.062-0.176). In ADL ( p  ≤ 0.0001, ES = 0.176). The combined cognitive and physical training had better efficacy for most cognitive functions and for ADL when compared with the physical training only.

System and method of active vibration control for an electro-mechanically cooled device

DOEpatents

Lavietes, Anthony D.; Mauger, Joseph; Anderson, Eric H.

2000-01-01

A system and method of active vibration control of an electro-mechanically cooled device is disclosed. A cryogenic cooling system is located within an environment. The cooling system is characterized by a vibration transfer function, which requires vibration transfer function coefficients. A vibration controller generates the vibration transfer function coefficients in response to various triggering events. The environments may differ by mounting apparatus, by proximity to vibration generating devices, or by temperature. The triggering event may be powering on the cooling system, reaching an operating temperature, or a reset action. A counterbalance responds to a drive signal generated by the vibration controller, based on the vibration signal and the vibration transfer function, which adjusts vibrations. The method first places a cryogenic cooling system within a first environment and then generates a first set of vibration transfer function coefficients, for a vibration transfer function of the cooling system. Next, the cryogenic cooling system is placed within a second environment and a second set of vibration transfer function coefficients are generated. Then, a counterbalance is driven, based on the vibration transfer function, to reduce vibrations received by a vibration sensitive element.

Transfer Function Identification Using Orthogonal Fourier Transform Modeling Functions

NASA Technical Reports Server (NTRS)

Morelli, Eugene A.

2013-01-01

A method for transfer function identification, including both model structure determination and parameter estimation, was developed and demonstrated. The approach uses orthogonal modeling functions generated from frequency domain data obtained by Fourier transformation of time series data. The method was applied to simulation data to identify continuous-time transfer function models and unsteady aerodynamic models. Model fit error, estimated model parameters, and the associated uncertainties were used to show the effectiveness of the method for identifying accurate transfer function models from noisy data.

Applications of Displacement Transfer Functions to Deformed Shape Predictions of the G-III Swept-Wing Structure

NASA Technical Reports Server (NTRS)

Lung, Shun-Fat; Ko, William L.

2016-01-01

In support of the Adaptive Compliant Trailing Edge [ACTE] project at the NASA Armstrong Flight Research Center, displacement transfer functions were applied to the swept wing of a Gulfstream G-III airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) to obtain deformed shape predictions. Four strainsensing lines (two on the lower surface, two on the upper surface) were used to calculate the deformed shape of the G III wing under bending and torsion. There being an insufficient number of surface strain sensors, the existing G III wing box finite element model was used to generate simulated surface strains for input to the displacement transfer functions. The resulting predicted deflections have good correlation with the finite-element generated deflections as well as the measured deflections from the ground load calibration test. The convergence study showed that the displacement prediction error at the G III wing tip can be reduced by increasing the number of strain stations (for each strain-sensing line) down to a minimum error of l.6 percent at 17 strain stations; using more than 17 strain stations yielded no benefit because the error slightly increased to 1.9% when 32 strain stations were used.

Transfer of training between distinct motor tasks after stroke: implications for task-specific approaches to upper-extremity neurorehabilitation.

PubMed

Schaefer, Sydney Y; Patterson, Chavelle B; Lang, Catherine E

2013-09-01

Although task-specific training is emerging as a viable approach for recovering motor function after stroke, there is little evidence for whether the effects of such training transfer to other functional motor tasks not directly practiced in therapy. The purpose of the current study was to test whether training on one motor task in individuals with chronic hemiparesis poststroke would transfer to untrained tasks that were either spatiotemporally similar or different. In all, 11 participants with chronic mild to moderate hemiparesis following stroke completed 5 days of supervised massed practice of a feeding task with their affected side. Performance on the feeding task, along with 2 other untrained functional upper-extremity motor tasks (sorting, dressing) was assessed before and after training. Performance of all 3 tasks improved significantly after training exclusively on 1 motor task. The amount of improvement in the untrained tasks was comparable and was not dependent on the degree of similarity to the trained task. Because the number and type of tasks that can be practiced are often limited within standard stroke rehabilitation, results from this study will be useful for designing task-specific training plans to maximize therapy benefits.

Experimental Determination of the Dynamic Hydraulic Transfer Function for the J-2X Oxidizer Turbopump. Part One; Methodology

NASA Technical Reports Server (NTRS)

Zoladz, Tom; Patel, Sandeep; Lee, Erik; Karon, Dave

2011-01-01

An advanced methodology for extracting the hydraulic dynamic pump transfer matrix (Yp) for a cavitating liquid rocket engine turbopump inducer+impeller has been developed. The transfer function is required for integrated vehicle pogo stability analysis as well as optimization of local inducer pumping stability. Laboratory pulsed subscale waterflow test of the J-2X oxygen turbo pump is introduced and our new extraction method applied to the data collected. From accurate measures of pump inlet and discharge perturbational mass flows and pressures, and one-dimensional flow models that represents complete waterflow loop physics, we are able to derive Yp and hence extract the characteristic pump parameters: compliance, pump gain, impedance, mass flow gain. Detailed modeling is necessary to accurately translate instrument plane measurements to the pump inlet and discharge and extract Yp. We present the MSFC Dynamic Lump Parameter Fluid Model Framework and describe critical dynamic component details. We report on fit minimization techniques, cost (fitness) function derivation, and resulting model fits to our experimental data are presented. Comparisons are made to alternate techniques for spatially translating measurement stations to actual pump inlet and discharge.

Multiconfiguration Pair-Density Functional Theory Outperforms Kohn-Sham Density Functional Theory and Multireference Perturbation Theory for Ground-State and Excited-State Charge Transfer.

PubMed

Ghosh, Soumen; Sonnenberger, Andrew L; Hoyer, Chad E; Truhlar, Donald G; Gagliardi, Laura

2015-08-11

The correct description of charge transfer in ground and excited states is very important for molecular interactions, photochemistry, electrochemistry, and charge transport, but it is very challenging for Kohn-Sham (KS) density functional theory (DFT). KS-DFT exchange-correlation functionals without nonlocal exchange fail to describe both ground- and excited-state charge transfer properly. We have recently proposed a theory called multiconfiguration pair-density functional theory (MC-PDFT), which is based on a combination of multiconfiguration wave function theory with a new type of density functional called an on-top density functional. Here we have used MC-PDFT to study challenging ground- and excited-state charge-transfer processes by using on-top density functionals obtained by translating KS exchange-correlation functionals. For ground-state charge transfer, MC-PDFT performs better than either the PBE exchange-correlation functional or CASPT2 wave function theory. For excited-state charge transfer, MC-PDFT (unlike KS-DFT) shows qualitatively correct behavior at long-range with great improvement in predicted excitation energies.

Application of 'Six Sigma{sup TM}' and 'Design of Experiment' for Cementation - Recipe Development for Evaporator Concentrate for NPP Ling AO, Phase II (China) - 12555

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fehrmann, Henning; Perdue, Robert

2012-07-01

Cementation of radioactive waste is a common technology. The waste is mixed with cement and water and forms a stable, solid block. The physical properties like compression strength or low leach ability depends strongly on the cement recipe. Due to the fact that this waste cement mixture has to fulfill special requirements, a recipe development is necessary. The Six Sigma{sup TM}' DMAIC methodology, together with the Design of experiment (DoE) approach, was employed to optimize the process of a recipe development for cementation at the Ling Ao nuclear power plant (NPP) in China. The DMAIC offers a structured, systematical andmore » traceable process to derive test parameters. The DoE test plans and statistical analysis is efficient regarding the amount of test runs and the benefit gain by getting a transfer function. A transfer function enables simulation which is useful to optimize the later process and being responsive to changes. The DoE method was successfully applied for developing a cementation recipe for both evaporator concentrate and resin waste in the plant. The key input parameters were determined, evaluated and the control of these parameters were included into the design. The applied Six Sigma{sup TM} tools can help to organize the thinking during the engineering process. Data are organized and clearly presented. Various variables can be limited to the most important ones. The Six Sigma{sup TM} tools help to make the thinking and decision process trace able. The tools can help to make data driven decisions (e.g. C and E Matrix). But the tools are not the only golden way. Results from scoring tools like the C and E Matrix need close review before using them. The DoE is an effective tool for generating test plans. DoE can be used with a small number of tests runs, but gives a valuable result from an engineering perspective in terms of a transfer function. The DoE prediction results, however, are only valid in the tested area. So a careful selection of input parameter and their limits for setting up a DoE is very important. An extrapolation of results is not recommended because the results are not reliable out of the tested area. (authors)« less

Development of the Coastal Zone Color Scanner for NIMBUS 7. Volume 2: Test and performance data, revision A

NASA Technical Reports Server (NTRS)

1979-01-01

The results of the Coastal Zone Color Scanner protoflight tests are examined in detail while some of the test results are evaluated with respect to expected performance. Performance characteristics examined include spectral response, signal to noise ratio as a function of radiance input, radiance response, the modulation transfer function, and the field of view and coregistration. The results of orbital sequence tests are also included. The in orbit performance or return of radiometric data in the six spectral bands is evaluated along with the data processing sequence necessary to derive the final data products. Examples of the raw data are given and the housekeeping or diagnostic data which provides information on the day to day health or status of the instrument are discussed.

Sub-scale Waterflow Cavitation and Dynamic Transfer Function Testing of an Oxidizer Turbo-Pump Combined Inducer and Impeller

NASA Technical Reports Server (NTRS)

Karon, D. M.; Patel, S. K.; Zoladz, T. F.

2016-01-01

In 2009 and 2010, Concepts NREC prepared for and performed a series of tests on a 52% scale of a version of the Pratt & Whitney Rocketdyne J-2X Oxidizer Turbopump under a Phase III SBIR with NASA MSFC. The test article was a combined inducer and impeller, tested as a unit. This paper presents an overview of the test rig and facility, instrumentation, signal conditioning, data acquisition systems, testing approach, measurement developments, and lessons learned. Results from these tests were presented in the form of two papers at the previous JANNAF joint propulsion conference, in December of 2011.

Multilevel microvibration test for performance predictions of a space optical load platform

NASA Astrophysics Data System (ADS)

Li, Shiqi; Zhang, Heng; Liu, Shiping; Wang, Yue

2018-05-01

This paper presents a framework for the multilevel microvibration analysis and test of a space optical load platform. The test framework is conducted on three levels, including instrument, subsystem, and system level. Disturbance source experimental investigations are performed to evaluate the vibration amplitude and study vibration mechanism. Transfer characteristics of space camera are validated by a subsystem test, which allows the calculation of transfer functions from various disturbance sources to optical performance outputs. In order to identify the influence of the source on the spacecraft performance, a system level microvibration measurement test has been performed on the ground. From the time domain analysis and spectrum analysis of multilevel microvibration tests, we concluded that the disturbance source has a significant effect on its installation position. After transmitted through mechanical links, the residual vibration reduces to a background noise level. In addition, the angular microvibration of the platform jitter is mainly concentrated in the rotation of y-axes. This work is applied to a real practical application involving the high resolution satellite camera system.

Computer method for identification of boiler transfer functions

NASA Technical Reports Server (NTRS)

Miles, J. H.

1971-01-01

An iterative computer method is described for identifying boiler transfer functions using frequency response data. An objective penalized performance measure and a nonlinear minimization technique are used to cause the locus of points generated by a transfer function to resemble the locus of points obtained from frequency response measurements. Different transfer functions can be tried until a satisfactory empirical transfer function to the system is found. To illustrate the method, some examples and some results from a study of a set of data consisting of measurements of the inlet impedance of a single tube forced flow boiler with inserts are given.

Evaluation of modulation transfer function of optical lens system by support vector regression methodologies - A comparative study

NASA Astrophysics Data System (ADS)

Petković, Dalibor; Shamshirband, Shahaboddin; Saboohi, Hadi; Ang, Tan Fong; Anuar, Nor Badrul; Rahman, Zulkanain Abdul; Pavlović, Nenad T.

2014-07-01

The quantitative assessment of image quality is an important consideration in any type of imaging system. The modulation transfer function (MTF) is a graphical description of the sharpness and contrast of an imaging system or of its individual components. The MTF is also known and spatial frequency response. The MTF curve has different meanings according to the corresponding frequency. The MTF of an optical system specifies the contrast transmitted by the system as a function of image size, and is determined by the inherent optical properties of the system. In this study, the polynomial and radial basis function (RBF) are applied as the kernel function of Support Vector Regression (SVR) to estimate and predict estimate MTF value of the actual optical system according to experimental tests. Instead of minimizing the observed training error, SVR_poly and SVR_rbf attempt to minimize the generalization error bound so as to achieve generalized performance. The experimental results show that an improvement in predictive accuracy and capability of generalization can be achieved by the SVR_rbf approach in compare to SVR_poly soft computing methodology.

Rapid Transfer of Abstract Rules to Novel Contexts in Human Lateral Prefrontal Cortex

PubMed Central

Cole, Michael W.; Etzel, Joset A.; Zacks, Jeffrey M.; Schneider, Walter; Braver, Todd S.

2011-01-01

Flexible, adaptive behavior is thought to rely on abstract rule representations within lateral prefrontal cortex (LPFC), yet it remains unclear how these representations provide such flexibility. We recently demonstrated that humans can learn complex novel tasks in seconds. Here we hypothesized that this impressive mental flexibility may be possible due to rapid transfer of practiced rule representations within LPFC to novel task contexts. We tested this hypothesis using functional MRI and multivariate pattern analysis, classifying LPFC activity patterns across 64 tasks. Classifiers trained to identify abstract rules based on practiced task activity patterns successfully generalized to novel tasks. This suggests humans can transfer practiced rule representations within LPFC to rapidly learn new tasks, facilitating cognitive performance in novel circumstances. PMID:22125519

Horizontal gene transfer in parasitic plants.

PubMed

Davis, Charles C; Xi, Zhenxiang

2015-08-01

Horizontal gene transfer (HGT) between species has been a major focus of plant evolutionary research during the past decade. Parasitic plants, which establish a direct connection with their hosts, have provided excellent examples of how these transfers are facilitated via the intimacy of this symbiosis. In particular, phylogenetic studies from diverse clades indicate that parasitic plants represent a rich system for studying this phenomenon. Here, HGT has been shown to be astonishingly high in the mitochondrial genome, and appreciable in the nuclear genome. Although explicit tests remain to be performed, some transgenes have been hypothesized to be functional in their recipient species, thus providing a new perspective on the evolution of novelty in parasitic plants. Copyright © 2015 Elsevier Ltd. All rights reserved.

Implementation and extension of the impulse transfer function method for future application to the space shuttle project. Volume 2: Program description and user's guide

NASA Technical Reports Server (NTRS)

Patterson, G.

1973-01-01

The data processing procedures and the computer programs were developed to predict structural responses using the Impulse Transfer Function (ITF) method. There are three major steps in the process: (1) analog-to-digital (A-D) conversion of the test data to produce Phase I digital tapes (2) processing of the Phase I digital tapes to extract ITF's and storing them in a permanent data bank, and (3) predicting structural responses to a set of applied loads. The analog to digital conversion is performed by a standard package which will be described later in terms of the contents of the resulting Phase I digital tape. Two separate computer programs have been developed to perform the digital processing.

A Two-Time Scale Decentralized Model Predictive Controller Based on Input and Output Model

PubMed Central

Niu, Jian; Zhao, Jun; Xu, Zuhua; Qian, Jixin

2009-01-01

A decentralized model predictive controller applicable for some systems which exhibit different dynamic characteristics in different channels was presented in this paper. These systems can be regarded as combinations of a fast model and a slow model, the response speeds of which are in two-time scale. Because most practical models used for control are obtained in the form of transfer function matrix by plant tests, a singular perturbation method was firstly used to separate the original transfer function matrix into two models in two-time scale. Then a decentralized model predictive controller was designed based on the two models derived from the original system. And the stability of the control method was proved. Simulations showed that the method was effective. PMID:19834542

Quantitative phase imaging method based on an analytical nonparaxial partially coherent phase optical transfer function.

PubMed

Bao, Yijun; Gaylord, Thomas K

2016-11-01

Multifilter phase imaging with partially coherent light (MFPI-PC) is a promising new quantitative phase imaging method. However, the existing MFPI-PC method is based on the paraxial approximation. In the present work, an analytical nonparaxial partially coherent phase optical transfer function is derived. This enables the MFPI-PC to be extended to the realistic nonparaxial case. Simulations over a wide range of test phase objects as well as experimental measurements on a microlens array verify higher levels of imaging accuracy compared to the paraxial method. Unlike the paraxial version, the nonparaxial MFPI-PC with obliquity factor correction exhibits no systematic error. In addition, due to its analytical expression, the increase in computation time compared to the paraxial version is negligible.

Advancing Autonomous Operations for Deep Space Vehicles

NASA Technical Reports Server (NTRS)

Haddock, Angie T.; Stetson, Howard K.

2014-01-01

Starting in Jan 2012, the Advanced Exploration Systems (AES) Autonomous Mission Operations (AMO) Project began to investigate the ability to create and execute "single button" crew initiated autonomous activities [1]. NASA Marshall Space Flight Center (MSFC) designed and built a fluid transfer hardware test-bed to use as a sub-system target for the investigations of intelligent procedures that would command and control a fluid transfer test-bed, would perform self-monitoring during fluid transfers, detect anomalies and faults, isolate the fault and recover the procedures function that was being executed, all without operator intervention. In addition to the development of intelligent procedures, the team is also exploring various methods for autonomous activity execution where a planned timeline of activities are executed autonomously and also the initial analysis of crew procedure development. This paper will detail the development of intelligent procedures for the NASA MSFC Autonomous Fluid Transfer System (AFTS) as well as the autonomous plan execution capabilities being investigated. Manned deep space missions, with extreme communication delays with Earth based assets, presents significant challenges for what the on-board procedure content will encompass as well as the planned execution of the procedures.

Detectability matters: conspicuous nestling mouth colours make prey transfer easier for parents in a cavity nesting bird.

PubMed

Dugas, Matthew B

2015-11-01

An often underappreciated function of signals is to notify receivers of the presence and position of senders. The colours that ornament the mouthparts of nestling birds, for example, have been hypothesized to evolve via selective pressure generated by parents' inability to efficiently detect and feed nestlings without such visually conspicuous targets. This proposed mechanism has primarily been evaluated with comparative studies and experimental tests for parental allocation bias, leaving untested the central assumption of this detectability hypothesis, that provisioning offspring is a visually challenging task for avian parents and conspicuous mouths help. To test this assumption, I manipulated the mouths of nestling house sparrows to appear minimally and maximally conspicuous, and quantified prey transfer difficulty as the total duration of a feeding event and the number of transfer attempts required. Prey transfer to inconspicuous nestlings was, as predicted, more difficult. While this suggests that detectability constraints could shape nestling mouth colour evolution, even minimally conspicuous nestlings were not prohibitively difficult for parents to feed, indicating that a more nuanced explanation for interspecific diversity in this trait is needed. © 2015 The Author(s).

Gene transfer, expression, and sarcomeric incorporation of a headless myosin molecule in cardiac myocytes: evidence for a reserve in myofilament motor function

PubMed Central

Vandenboom, Rene; Herron, Todd; Favre, Elizabeth; Albayya, Faris P.

2011-01-01

The purpose of this study was to implement a living myocyte in vitro model system to test whether a motor domain-deleted headless myosin construct could be incorporated into the sarcomere and affect contractility. To this end we used gene transfer to express a “headless” myosin heavy chain (headless-MHC) in complement with the native full-length myosin motors in the cardiac sarcomere. An NH2-terminal Flag epitope was used for unique detection of the motor domain-deleted headless-MHC. Total MHC content (i.e., headless-MHC + endogenous MHC) remained constant, while expression of the headless-MHC in transduced myocytes increased from 24 to 72 h after gene transfer until values leveled off at 96 h after gene transfer, at which time the headless-MHC comprised ∼20% of total MHC. Moreover, immunofluorescence labeling and confocal imaging confirmed expression and demonstrated incorporation of the headless-MHC in the A band of the cardiac sarcomere. Functional measurements in intact myocytes showed that headless-MHC modestly reduced amplitude of dynamic twitch contractions compared with controls (P < 0.05). In chemically permeabilized myocytes, maximum steady-state isometric force and the tension-pCa relationship were unaltered by the headless-MHC. These data suggest that headless-MHC can express to 20% of total myosin and incorporate into the sarcomere yet have modest to no effects on dynamic and steady-state contractile function. This would indicate a degree of functional tolerance in the sarcomere for nonfunctional myosin molecules. PMID:21112946

A 3,000-year quantitative drought record derived from XRF element data from a south Texas playa

NASA Astrophysics Data System (ADS)

Livsey, D. N.; Simms, A.; Hangsterfer, A.; Nisbet, R.; DeWitt, R.

2013-12-01

Recent droughts throughout the central United States highlight the need for a better understanding of the past frequency and severity of drought occurrence. Current records of past drought for the south Texas coast are derived from tree-ring data that span approximately the last 900 years before present (BP). In this study we utilize a supervised learning routine to create a transfer function between X-Ray Fluorescence (XRF) derived elemental data from Laguna Salada, Texas core LS10-02 to a locally derived tree-ring drought record. From this transfer function the 900 BP tree-ring drought record was extended to 3,000 BP. The supervised learning routine was trained on the first 100 years of XRF element data and tree-ring drought data to create the transfer function and training data set output. The model was then projected from the XRF elemental data for the next 800 years to create a deployed data set output and to test the transfer function parameters. The coefficients of determination between the model output and observed values are 0.77 and 0.70 for the 100-year training data set and 900-year deployed data set respectively. Given the relatively high coefficients of determination for both the training data set and deployed data set we interpret the model parameters are fairly robust and that a high-resolution drought record can be derived from the XRF element data. These results indicate that XRF element data can be used as a quantitative tool to reconstruct past drought records.

Longitudinal Analysis of Music Education on Executive Functions in Primary School Children

PubMed Central

Jaschke, Artur C.; Honing, Henkjan; Scherder, Erik J. A.

2018-01-01

Background: Research on the effects of music education on cognitive abilities has generated increasing interest across the scientific community. Nonetheless, longitudinal studies investigating the effects of structured music education on cognitive sub-functions are still rare. Prime candidates for investigating a relationship between academic achievement and music education appear to be executive functions such as planning, working memory, and inhibition. Methods: One hundred and forty-seven primary school children, Mage = 6.4 years, SD = 0.65 were followed for 2.5 years. Participants were randomized into four groups: two music intervention groups, one active visual arts group, and a no arts control group. Neuropsychological tests assessed verbal intelligence and executive functions. Additionally, a national pupil monitor provided data on academic performance. Results: Children in the visual arts group perform better on visuospatial memory tasks as compared to the three other conditions. However, the test scores on inhibition, planning and verbal intelligence increased significantly in the two music groups over time as compared to the visual art and no arts controls. Mediation analysis with executive functions and verbal IQ as mediator for academic performance have shown a possible far transfer effect from executive sub-function to academic performance scores. Discussion: The present results indicate a positive influence of long-term music education on cognitive abilities such as inhibition and planning. Of note, following a two-and-a-half year long visual arts program significantly improves scores on a visuospatial memory task. All results combined, this study supports a far transfer effect from music education to academic achievement mediated by executive sub-functions. PMID:29541017

Longitudinal Analysis of Music Education on Executive Functions in Primary School Children.

PubMed

Jaschke, Artur C; Honing, Henkjan; Scherder, Erik J A

2018-01-01

Background: Research on the effects of music education on cognitive abilities has generated increasing interest across the scientific community. Nonetheless, longitudinal studies investigating the effects of structured music education on cognitive sub-functions are still rare. Prime candidates for investigating a relationship between academic achievement and music education appear to be executive functions such as planning, working memory, and inhibition. Methods: One hundred and forty-seven primary school children, M age = 6.4 years, SD = 0.65 were followed for 2.5 years. Participants were randomized into four groups: two music intervention groups, one active visual arts group, and a no arts control group. Neuropsychological tests assessed verbal intelligence and executive functions. Additionally, a national pupil monitor provided data on academic performance. Results: Children in the visual arts group perform better on visuospatial memory tasks as compared to the three other conditions. However, the test scores on inhibition, planning and verbal intelligence increased significantly in the two music groups over time as compared to the visual art and no arts controls. Mediation analysis with executive functions and verbal IQ as mediator for academic performance have shown a possible far transfer effect from executive sub-function to academic performance scores. Discussion: The present results indicate a positive influence of long-term music education on cognitive abilities such as inhibition and planning. Of note, following a two-and-a-half year long visual arts program significantly improves scores on a visuospatial memory task. All results combined, this study supports a far transfer effect from music education to academic achievement mediated by executive sub-functions.

Fabrication of functional fibronectin patterns by nanosecond excimer laser direct write for tissue engineering applications.

PubMed

Grigorescu, S; Hindié, M; Axente, E; Carreiras, F; Anselme, K; Werckmann, J; Mihailescu, I N; Gallet, O

2013-07-01

Laser direct write techniques represent a prospective alternative for engineering a new generation of hybrid biomaterials via the creation of patterns consisting of biological proteins onto practically any type of substrate. In this paper we report on the characterization of fibronectin features obtained onto titanium substrates by UV nanosecond laser transfer. Fourier-transform infrared spectroscopy measurements evidenced no modification in the secondary structure of the post-transferred protein. The molecular weight of the transferred protein was identical to the initial fibronectin, no fragment bands being found in the transferred protein's Western blot migration profile. The presence of the cell-binding domain sequence and the mannose groups within the transferred molecules was revealed by anti-fibronectin monoclonal antibody immunolabelling and FITC-Concanavalin-A staining, respectively. The in vitro tests performed with MC3T3-E1 osteoblast-like cells and Swiss-3T3 fibroblasts showed that the cells' morphology and spreading were strongly influenced by the presence of the fibronectin spots.

Integration Of Heat Transfer Coefficient In Glass Forming Modeling With Special Interface Element

NASA Astrophysics Data System (ADS)

Moreau, P.; César de Sá, J.; Grégoire, S.; Lochegnies, D.

2007-05-01

Numerical modeling of the glass forming processes requires the accurate knowledge of the heat exchange between the glass and the forming tools. A laboratory testing is developed to determine the evolution of the heat transfer coefficient in different glass/mould contact conditions (contact pressure, temperature, lubrication…). In this paper, trials are performed to determine heat transfer coefficient evolutions in experimental conditions close to the industrial blow-and-blow process conditions. In parallel of this work, a special interface element is implemented in a commercial Finite Element code in order to deal with heat transfer between glass and mould for non-meshing meshes and evolutive contact. This special interface element, implemented by using user subroutines, permits to introduce the previous heat transfer coefficient evolutions in the numerical modelings at the glass/mould interface in function of the local temperatures, contact pressures, contact time and kind of lubrication. The blow-and-blow forming simulation of a perfume bottle is finally performed to assess the special interface element performance.

[Interpretation and use of routine pulmonary function tests: Spirometry, static lung volumes, lung diffusion, arterial blood gas, methacholine challenge test and 6-minute walk test].

PubMed

Bokov, P; Delclaux, C

2016-02-01

Resting pulmonary function tests (PFT) include the assessment of ventilatory capacity: spirometry (forced expiratory flows and mobilisable volumes) and static volume assessment, notably using body plethysmography. Spirometry allows the potential definition of obstructive defect, while static volume assessment allows the potential definition of restrictive defect (decrease in total lung capacity) and thoracic hyperinflation (increase in static volumes). It must be kept in mind that this evaluation is incomplete and that an assessment of ventilatory demand is often warranted, especially when facing dyspnoea: evaluation of arterial blood gas (searching for respiratory insufficiency) and measurement of the transfer coefficient of the lung, allowing with the measurement of alveolar volume to calculate the diffusing capacity of the lung for CO (DLCO: assessment of alveolar-capillary wall and capillary blood volume). All these pulmonary function tests have been the subject of an Americano-European Task force (standardisation of lung function testing) published in 2005, and translated in French in 2007. Interpretative strategies for lung function tests have been recommended, which define abnormal lung function tests using the 5th and 95th percentiles of predicted values (lower and upper limits of normal values). Thus, these recommendations need to be implemented in all pulmonary function test units. A methacholine challenge test will only be performed in the presence of an intermediate pre-test probability for asthma (diagnostic uncertainty), which is an infrequent setting. The most convenient exertional test is the 6-minute walk test that allows the assessment of walking performance, the search for arterial desaturation and the quantification of dyspnoea complaint. Copyright © 2015 Société nationale française de médecine interne (SNFMI). Published by Elsevier SAS. All rights reserved.

An experimental study of the velocity-forced flame response of a lean-premixed multi-nozzle can combustor for gas turbines

NASA Astrophysics Data System (ADS)

Szedlmayer, Michael Thomas

The velocity forced flame response of a multi-nozzle, lean-premixed, swirl-stabilized, turbulent combustor was investigated at atmospheric pressure. The purpose of this study was to analyze the mechanisms that allowed velocity fluctuations to cause fluctuations in the rate of heat release in a gas turbine combustor experiencing combustion instability. Controlled velocity fluctuations were introduced to the combustor by a rotating siren device which periodically allowed the air-natural gas mixture to flow. The velocity fluctuation entering the combustor was measured using the two-microphone method. The resulting heat release rate fluctuation was measured using CH* chemiluminescence. The global response of the flame was quantified using the flame transfer function with the velocity fluctuation as the input and the heat release rate fluctuation as the output. Velocity fluctuation amplitude was initially maintained at 5% of the inlet velocity in order to remain in the linear response regime. Flame transfer function measurements were acquired at a wide range of operating conditions and forcing frequencies. The selected range corresponds to the conditions and instability frequencies typical of real gas turbine combustors. Multi-nozzle flame transfer functions were found to bear a qualitative similarity to the single-nozzle flame transfer functions in the literature. The flame transfer function gain exhibited alternating minima and maxima while the phase decreased linearly with increasing forcing frequency. Several normalization techniques were applied to all flame transfer function data in an attempt to collapse the data into a single curve. The best collapse was found to occur using a Strouhal number which was the ratio of the characteristic flame length to the wavelength of the forced disturbance. Critical values of Strouhal number are used to predict the shedding of vortical structures in shear layers. Because of the collapse observed when the flame transfer functions are plotted versus Strouhal number, vortical structures are thought to have a strong influence on the response of this multi-nozzle configuration. The structure of heat release rate fluctuations throughout the flame is analyzed using CH* chemiluminescence acquired with a high speed camera. Flames with a similar level of flame transfer function gain are found to exhibit similarity in the spatial distribution of their heat release rate fluctuations, regardless of the operating condition. Flames with high gain are found to have high amplitude fluctuations near the downstream end of the flame, with weak fluctuations near the flame base. The phase of the downstream fluctuations changes minimally across the downstream region, indicating that they occur inphase. Flames with low gain exhibit stronger fluctuations near the flame base, but weak fluctuations in the downstream region. The phase of the fluctuations near the flame base changes continuously along the flame axis, indicating that parts of the flame will fluctuate out-of-phase. Accordingly, from a global perspective, destructive interference between heat release rate fluctuations in different parts of the flame can be expected. The behavior observed in the flame is ascribed to the interaction of acoustic velocity fluctuations, vortical disturbances and swirl fluctuations. The response of the multi-nozzle flame to high amplitude velocity fluctuations was tested for a single operating condition. Based on the global flame response, most frequencies responded linearly over the tested range of amplitudes. Nonlinear effects were found to occur at three frequencies. The behaviors observed at these frequencies matched those observed in the literature and included flame response saturation and mode triggering. For conditions which responded linearly at all amplitudes, the structure of heat release rate fluctuations was found to remain nearly constant. For conditions with nonlinear behavior, the structure of the fluctuations was a function of the forcing amplitude, particularly in the downstream region. The behavior of the multi-nozzle flame was compared directly to that of a single-nozzle flame of the same nozzle design. The multi-nozzle characteristic flame length was found to be on average 10% longer than for the single-nozzle flame. The flame transfer functions from the two cases were found to exhibit qualitative similarity, where the frequencies at which the extrema occur are similar. The actual value of gain for the same operating condition and frequency does, however, vary by more than a factor of two in some cases. The phase value can also vary by as much as pi radians. These differences indicate that single-nozzle flame transfer functions should not be used directly to predict the instability driving force of real gas turbine combustors.

Development of InSb charge-coupled infrared imaging devices: Linear imager

NASA Technical Reports Server (NTRS)

Phillips, J. D.

1976-01-01

The following results were accomplished in the development of charge coupled infrared imaging devices: (1) a four-phase overlapping gate with 9 transfers (2-bits) and 1.0-mil gate lengths was successfully operated, (2) the measured transfer efficiency of 0.975 for this device is in excellent agreement with predictions for the reduced gate length device, (3) mask revisions of the channel stop metal on the 8582 mask have been carried out with the result being a large increase in the dc yield of the tested devices, (4) partial optical sensitivity to chopped blackbody radiation was observed for an 8582 9-bit imager, (5) analytical consideration of the modulation transfer function degradation caused by transfer inefficiency in the CCD registers was presented, and (6) for larger array lengths or for the insertion of isolated bits between sensors, improvements in InSb fabrication technology with corresponding decrease in the interface state density are required.

Prism adaptation in alternately exposed hands.

PubMed

Redding, Gordon M; Wallace, Benjamin

2013-08-01

We assessed intermanual transfer of the proprioceptive realignment aftereffects of prism adaptation in right-handers by examining alternate target pointing with the two hands for 40 successive trials, 20 with each hand. Adaptation for the right hand was not different as a function of exposure sequence order or postexposure test order, in contrast with adaptation for the left hand. Adaptation was greater for the left hand when the right hand started the alternate pointing than when the sequence of target-pointing movements started with the left hand. Also, the largest left-hand adaptation appeared when that hand was tested first after exposure. Terminal error during exposure varied in cycles for the two hands, converging on zero when the right hand led, but no difference appeared between the two hands when the left hand led. These results suggest that transfer of proprioceptive realignment occurs from the right to the left hand during both exposure and postexposure testing. Such transfer reflects the process of maintaining spatial alignment between the two hands. Normally, the left hand appears to be calibrated with the right-hand spatial map, and when the two hands are misaligned, the left-hand spatial map is realigned with the right-hand spatial map.

Targeting latent function: encouraging effective encoding for successful memory training and transfer.

PubMed

Lustig, Cindy; Flegal, Kristin E

2008-12-01

Cognitive training programs for older adults often result in improvements at the group level. However, there are typically large age and individual differences in the size of training benefits. These differences may be related to the degree to which participants implement the processes targeted by the training program. To test this possibility, we tested older adults in a memory-training procedure either under specific strategy instructions designed to encourage semantic, integrative encoding, or in a condition that encouraged time and attention to encoding but allowed participants to choose their own strategy. Both conditions improved the performance of old-old adults relative to an earlier study (D. Bissig & C. Lustig, 2007) and reduced self-reports of everyday memory errors. Performance in the strategy-instruction group was related to preexisting ability; performance in the strategy?choice group was not. The strategy-choice group performed better on a laboratory transfer test of recognition memory, and training performance was correlated with reduced everyday memory errors. Training programs that target participants' latent but inefficiently used abilities while allowing flexibility in bringing those abilities to bear may best promote effective training and transfer. Copyright (c) 2009 APA, all rights reserved.

The benefits of using a vacuum-assisted socket system to improve balance and gait in elderly transtibial amputees.

PubMed

Samitier, C Beatriz; Guirao, Lluis; Costea, Maria; Camós, Josep M; Pleguezuelos, Eulogio

2016-02-01

Lower limb amputation leads to impaired balance, ambulation, and transfers. Proper fit of the prosthesis is a determining factor for successful ambulation. Vacuum-assisted socket systems extract air from the socket, which decreases pistoning and probability of soft-tissue injuries and increases proprioception and socket comfort. To investigate the effect of vacuum-assisted socket system on transtibial amputees' performance-based and perceived balance, transfers, and gait. Quasi-experimental before-and-after study. Subjects were initially assessed using their prosthesis with the regular socket and re-evaluated 4 weeks after fitting including the vacuum-assisted socket system. We evaluated the mobility grade using Medicare Functional Classification Level, Berg Balance Scale, Four Square Step Test, Timed Up and Go Test, the 6-Min Walk Test, the Locomotor Capabilities Index, Satisfaction with Prosthesis (SAT-PRO questionnaire), and Houghton Scale. A total of 16 unilateral transtibial dysvascular amputees, mean age 65.12 (standard deviation = 10.15) years. Using the vacuum-assisted socket system, the patients significantly improved in balance, gait, and transfers: scores of the Berg Balance Scale increased from 45.75 (standard deviation = 6.91) to 49.06 (standard deviation = 5.62) (p < 0.01), Four Square Step Test decreased from 18.18 (standard deviation = 3.84) s to 14.97 (3.9) s (p < 0.01), Timed Up and Go Test decreased from 14.3 (standard deviation = 3.29) s to 11.56 (2.46) s (p < 0.01). The distance walked in the 6-Min Walk Test increased from 288.53 (standard deviation = 59.57) m to 321.38 (standard deviation = 72.81) m (p < 0.01). Vacuum-assisted socket systems are useful for improving balance, gait, and transfers in over-50-year-old dysvascular transtibial amputees. This study gives more insight into the use of vacuum-assisted socket systems to improve elderly transtibial dysvascular amputees' functionality and decrease their risk of falls. The use of an additional distal valve in the socket should be considered in patients with a lower activity level. © The International Society for Prosthetics and Orthotics 2014.

Artificial Neural Network with Hardware Training and Hardware Refresh

NASA Technical Reports Server (NTRS)

Duong, Tuan A. (Inventor)

2003-01-01

A neural network circuit is provided having a plurality of circuits capable of charge storage. Also provided is a plurality of circuits each coupled to at least one of the plurality of charge storage circuits and constructed to generate an output in accordance with a neuron transfer function. Each of a plurality of circuits is coupled to one of the plurality of neuron transfer function circuits and constructed to generate a derivative of the output. A weight update circuit updates the charge storage circuits based upon output from the plurality of transfer function circuits and output from the plurality of derivative circuits. In preferred embodiments, separate training and validation networks share the same set of charge storage circuits and may operate concurrently. The validation network has a separate transfer function circuits each being coupled to the charge storage circuits so as to replicate the training network s coupling of the plurality of charge storage to the plurality of transfer function circuits. The plurality of transfer function circuits may be constructed each having a transconductance amplifier providing differential currents combined to provide an output in accordance with a transfer function. The derivative circuits may have a circuit constructed to generate a biased differential currents combined so as to provide the derivative of the transfer function.

Identification of boiler inlet transfer functions and estimation of system parameters

NASA Technical Reports Server (NTRS)

Miles, J. H.

1972-01-01

An iterative computer method is described for identifying boiler transfer functions using frequency response data. An objective penalized performance measure and a nonlinear minimization technique are used to cause the locus of points generated by a transfer function to resemble the locus of points obtained from frequency response measurements. Different transfer functions can be tried until a satisfactory empirical transfer function of the system is found. To illustrate the method, some examples and some results from a study of a set of data consisting of measurements of the inlet impedance of a single tube forced flow boiler with inserts are given.

Information theory and robotics meet to study predator-prey interactions

NASA Astrophysics Data System (ADS)

Neri, Daniele; Ruberto, Tommaso; Cord-Cruz, Gabrielle; Porfiri, Maurizio

2017-07-01

Transfer entropy holds promise to advance our understanding of animal behavior, by affording the identification of causal relationships that underlie animal interactions. A critical step toward the reliable implementation of this powerful information-theoretic concept entails the design of experiments in which causal relationships could be systematically controlled. Here, we put forward a robotics-based experimental approach to test the validity of transfer entropy in the study of predator-prey interactions. We investigate the behavioral response of zebrafish to a fear-evoking robotic stimulus, designed after the morpho-physiology of the red tiger oscar and actuated along preprogrammed trajectories. From the time series of the positions of the zebrafish and the robotic stimulus, we demonstrate that transfer entropy correctly identifies the influence of the stimulus on the focal subject. Building on this evidence, we apply transfer entropy to study the interactions between zebrafish and a live red tiger oscar. The analysis of transfer entropy reveals a change in the direction of the information flow, suggesting a mutual influence between the predator and the prey, where the predator adapts its strategy as a function of the movement of the prey, which, in turn, adjusts its escape as a function of the predator motion. Through the integration of information theory and robotics, this study posits a new approach to study predator-prey interactions in freshwater fish.

Rapid determination of soil quality and earthworm impacts on soil microbial communities using fluorescence-based respirometry

NASA Astrophysics Data System (ADS)

Prendergast-Miller, Miranda T.; Thurston, Josh; Taylor, Joe; Helgason, Thorunn; Ashauer, Roman; Hodson, Mark E.

2017-04-01

We applied a fluorescence-based respirometry method currently devised for aquatic ecotoxicology studies to rapidly measure soil microbial oxygen consumption as a function of soil quality. In this study, soil was collected from an arable wheat field and the field margin. These two soil habitats are known to differ in their soil quality due to differences in their use and management as well as plant, microbial and earthworm community. The earthworm Lumbricus terrestris was incubated in arable or margin soil for three weeks. After this initial phase, a transfer experiment was then conducted to test the hypothesis that earthworm 'migration' alters soil microbial community function and diversity. In this transfer experiment, earthworms incubated in margin soil were transferred to arable soil. The converse transfer (i.e. earthworms incubated in arable soil) was also conducted. Soils of each type with no earthworms were also incubated as controls. After a further four week incubation, the impact of earthworm migration on the soil microbial community was tested by measuring oxygen consumption. Replicated soil slurry subsamples were aliquoted into individual respirometer wells (600 μl volume) on a glass 24-well microplate (Loligo Systems, Denmark) fitted with non-invasive, reusable oxygen sensor spots. The sealed microplate was then attached to an oxygen fluorescence sensor (SDR SensorDish Reader, PreSens, Germany). Oxygen consumption was measured in real-time over a 2 hr period following standard operating procedures. Soil microbial activity was measured with and without an added carbon source (glucose or cellulose, 50 mg C L-1). Using this system, we were able to differentiate between soil type, earthworm treatment and C source. Earthworm-driven impacts on soil microbial oxygen consumption were also supported by changes in soil microbial community structure and diversity revealed using DNA-based sequencing techniques. This method provides a simple and rapid system for measuring soil quality and has the potential for use in a variety of scenarios investigating impacts on soil microbial function.

Derived Manding in Children with Autism: Synthesizing Skinner's Verbal Behavior with Relational Frame Theory

ERIC Educational Resources Information Center

Murphy, Carol; Barnes-Holmes, Dermot; Barnes-Holmes, Yvonne

2005-01-01

Mand functions for two stimuli (A1 and A2) were trained for 3 children with autism and were then incorporated into two related conditional discriminations (A1-B1/A2 -B2 and B1-C1/B2-C2). Tests were conducted to probe for a derived transfer of mand response functions from Al and A2 to C1 and C2, respectively. When 1 participant failed to…

Research on target information optics communications transmission characteristic and performance in multi-screens testing system

NASA Astrophysics Data System (ADS)

Li, Hanshan

2016-04-01

To enhance the stability and reliability of multi-screens testing system, this paper studies multi-screens target optical information transmission link properties and performance in long-distance, sets up the discrete multi-tone modulation transmission model based on geometric model of laser multi-screens testing system and visible light information communication principle; analyzes the electro-optic and photoelectric conversion function of sender and receiver in target optical information communication system; researches target information transmission performance and transfer function of the generalized visible-light communication channel; found optical information communication transmission link light intensity space distribution model and distribution function; derives the SNR model of information transmission communication system. Through the calculation and experiment analysis, the results show that the transmission error rate increases with the increment of transmission rate in a certain channel modulation depth; when selecting the appropriate transmission rate, the bit error rate reach 0.01.

Detection of nonlinear transfer functions by the use of Gaussian statistics

NASA Technical Reports Server (NTRS)

Sheppard, J. G.

1972-01-01

The possibility of using on-line signal statistics to detect electronic equipment nonlinearities is discussed. The results of an investigation using Gaussian statistics are presented, and a nonlinearity test that uses ratios of the moments of a Gaussian random variable is developed and discussed. An outline for further investigation is presented.

Optically coded nanocrystal taggants and optical frequency IDs

NASA Astrophysics Data System (ADS)

Williams, George M., Jr.; Allen, Thomas; Dupuy, Charles; Novet, Thomas; Schut, David

2010-04-01

A series of nanocrystal and nanocrystal quantum dot taggant technologies were developed for covertly tagging and tracking objects of interest. Homogeneous and heterogeneous nanocrystal taggant designs were developed and optimized for ultraviolet through infrared emissions, utilizing either Dexter energy transfer or Förster resonant energy transfer (FRET) between specific absorbing and emitting functionalities. The conversion efficiency, target-specific identification, and adhesion properties of the taggants were engineered by means of various surface ligand chemistries. The ability to engineer poly-functional ligands was shown effective in the detection of a biological agent simulant, detected through a NC photoluminescence that is altered in the presence of the agent of interest; the technique has broad potential applicability to chemical, biological, and explosive (CBE) agent detection. The NC photoluminescence can be detected by a remote LIDAR system; the performance of a taggant system has been modeled and subsequently verified in a series of controlled field tests. LIDAR detection of visible-emitting taggants was shown to exceed 2.8 km in calibrated field tests, and from these field data and calibrated laboratory measurements we predict >5 km range in the covert shortwavelength infrared (SWIR) spectral region.

Computer method for identification of boiler transfer functions

NASA Technical Reports Server (NTRS)

Miles, J. H.

1972-01-01

Iterative computer aided procedure was developed which provides for identification of boiler transfer functions using frequency response data. Method uses frequency response data to obtain satisfactory transfer function for both high and low vapor exit quality data.

Proceedings and findings of the 1976 Workshop on Ride Quality. [passenger acceptance of transportation systems

NASA Technical Reports Server (NTRS)

Kuhlthau, A. R. (Editor)

1976-01-01

The workshop was organized around the study of the three basic transfer functions required to evaluate and/or predict passenger acceptance of transportation systems: These are the vehicle, passenger, and value transfer functions. For the purpose of establishing working groups corresponding to the basic transfer functions, it was decided to split the vehicle transfer function into two distinct groups studying surface vehicles and air/marine vehicles, respectively.

Hydrogen slush density reference system

NASA Technical Reports Server (NTRS)

Weitzel, D. H.; Lowe, L. T.; Ellerbruch, D. A.; Cruz, J. E.; Sindt, C. F.

1971-01-01

A hydrogen slush density reference system was designed for calibration of field-type instruments and/or transfer standards. The device is based on the buoyancy principle of Archimedes. The solids are weighed in a low-mass container so arranged that solids and container are buoyed by triple-point liquid hydrogen during the weighing process. Several types of hydrogen slush density transducers were developed and tested for possible use as transfer standards. The most successful transducers found were those which depend on change in dielectric constant, after which the Clausius-Mossotti function is used to relate dielectric constant and density.

Skylab Rescue Space Vehicle OAT No. 1 Plugs in Test

NASA Technical Reports Server (NTRS)

Jevitt, S. J.

1973-01-01

A test is described which demonstrates the compatibility of the Skylab Rescue Space Vehicle systems, the ground support equipment, and off-site support facilities by proceeding through a simulated launch countdown, liftoff, and flight. The functions of propellant loading, umbilical ejection, holddown arm release, service arm retraction, liftoff, and inflight separation are simulated. An external power source supplies transfer power to internal, and instrument unit commands are simulated by the digital command system. The test outline is presented along with a list of references, intercommunications information, radio frequency matrix, and interface control chart.

5 CFR 351.302 - Transfer of employees.

Code of Federal Regulations, 2011 CFR

2011-01-01

... is not identified with an operating function specifically authorized at the time of transfer to... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Transfer of employees. 351.302 Section... FORCE Transfer of Function § 351.302 Transfer of employees. (a) Before a reduction in force is made in...

5 CFR 351.302 - Transfer of employees.

Code of Federal Regulations, 2010 CFR

2010-01-01

... is not identified with an operating function specifically authorized at the time of transfer to... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Transfer of employees. 351.302 Section... FORCE Transfer of Function § 351.302 Transfer of employees. (a) Before a reduction in force is made in...

5 CFR 351.302 - Transfer of employees.

Code of Federal Regulations, 2012 CFR

2012-01-01

... is not identified with an operating function specifically authorized at the time of transfer to... 5 Administrative Personnel 1 2012-01-01 2012-01-01 false Transfer of employees. 351.302 Section... FORCE Transfer of Function § 351.302 Transfer of employees. (a) Before a reduction in force is made in...

5 CFR 351.302 - Transfer of employees.

Code of Federal Regulations, 2014 CFR

2014-01-01

... is not identified with an operating function specifically authorized at the time of transfer to... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Transfer of employees. 351.302 Section... FORCE Transfer of Function § 351.302 Transfer of employees. (a) Before a reduction in force is made in...

5 CFR 351.302 - Transfer of employees.

Code of Federal Regulations, 2013 CFR

2013-01-01

... is not identified with an operating function specifically authorized at the time of transfer to... 5 Administrative Personnel 1 2013-01-01 2013-01-01 false Transfer of employees. 351.302 Section... FORCE Transfer of Function § 351.302 Transfer of employees. (a) Before a reduction in force is made in...

Testing promotes effector transfer.

PubMed

Boutin, Arnaud; Panzer, Stefan; Salesse, Robin N; Blandin, Yannick

2012-11-01

The retrieval of information from memory during testing has recently been shown to promote transfer in the verbal domain. Motor-related research, however, has ignored testing as a relevant method to enhance motor transfer. We thus investigated whether testing has the potential to induce generalised motor memories by favouring effector transfer. Participants were required to reproduce a spatial-temporal pattern of elbow extensions and flexions with their dominant right arm. We tested the ability of participants to transfer the original pattern (extrinsic transformation; i.e., goal-based configuration) or the mirrored pattern (intrinsic transformation; i.e., movement-based configuration) to the unpractised non-dominant left arm. To evaluate how testing affects motor transfer at 24-h testing, participants were either administered an initial testing session during early practice (early testing group) or shortly after the end of practice (late testing group; i.e., no alternation between practice and testing sessions). No initial testing session was completed for the control group. We found better effector transfer at 24-h testing for the early testing group for both extrinsic and intrinsic transformations of the movement pattern when compared with the control group, while no testing benefit was observed for the late testing group. This indicates that testing positively affects motor learning, yielding enhanced long-term transfer capabilities. We thus demonstrate the critical role of retrieval practice via testing during the process of motor memory encoding, and provide the conditions under which testing effectively contributes to the generalisation of motor memories. Copyright © 2012 Elsevier B.V. All rights reserved.

Testing a Method for Quantifying the Output of Implantable Middle Ear Hearing Devices

PubMed Central

Rosowski, J.J.; Chien, W.; Ravicz, M.E.; Merchant, S.N.

2008-01-01

This report describes tests of a standard practice for quantifying the performance of implantable middle ear hearing devices (also known as implantable hearing aids). The standard and these tests were initiated by the Food and Drug Administration of the United States Government. The tests involved measurements on two hearing devices, one commercially available and the other home built, that were implanted into ears removed from human cadavers. The tests were conducted to investigate the utility of the practice and its outcome measures: the equivalent ear canal sound pressure transfer function that relates electrically driven middle ear velocities to the equivalent sound pressure needed to produce those velocities, and the maximum effective ear canal sound pressure. The practice calls for measurements in cadaveric ears in order to account for the varied anatomy and function of different human middle ears. PMID:17406105

Characterization of vibration transfer paths in nose gearboxes of an AH-64 Apache

NASA Astrophysics Data System (ADS)

Islam, A. K. M. Anwarul; Dempsey, Paula J.; Feldman, Jason; Larsen, Chris

2014-03-01

Health monitoring of rotorcraft components, which is currently being performed by Health and Usage Monitoring Systems (HUMS) through analyzing vibration signatures of dynamic mechanical components, is very important for their safe and economic operation. Vibration diagnostic algorithms in HUMS analyze vibration signatures associated with faults and quantify them as condition indicators (CI) to predict component behavior. Vibration transfer paths (VTP) play important roles in CI response and are characterized by frequency response functions (FRF) derived from vibration signatures of dynamic mechanical components of a helicopter. With an objective to investigate the difference in VTP of a component in a helicopter and test stand, and to relate that to the CI response, VTP measurements were recorded from 0-50 kHz under similar conditions in the left and right nose gearboxes (NGBs) of an AH-64 Apache and an isolated left NGB in a test stand at NASA Glenn Research Center. The test fixture enabled the application of measured torques - common during an actual operation. Commercial and lab piezo shakers, and an impact hammer were used in both systems to collect the vibration response using two types of commercially available accelerometers under various test conditions. The FRFs of both systems were found to be consistent, and certain real-world installation and maintenance issues, such as sensor alignments, locations and installation torques, had minimal effect on the VTP. However, gear vibration transfer path dynamics appeared to be somewhat dependent on presence of oil, and the lightly-damped ring gear produced sharp and closer transfer path resonances.

Nerve transfers in tetraplegia I: Background and technique

PubMed Central

Brown, Justin M.

2011-01-01

Background: The recovery of hand function is consistently rated as the highest priority for persons with tetraplegia. Recovering even partial arm and hand function can have an enormous impact on independence and quality of life of an individual. Currently, tendon transfers are the accepted modality for improving hand function. In this procedure, the distal end of a functional muscle is cut and reattached at the insertion site of a nonfunctional muscle. The tendon transfer sacrifices the function at a lesser location to provide function at a more important location. Nerve transfers are conceptually similar to tendon transfers and involve cutting and connecting a healthy but less critical nerve to a more important but paralyzed nerve to restore its function. Methods: We present a case of a 28-year-old patient with a C5-level ASIA B (international classification level 1) injury who underwent nerve transfers to restore arm and hand function. Intact peripheral innervation was confirmed in the paralyzed muscle groups corresponding to finger flexors and extensors, wrist flexors and extensors, and triceps bilaterally. Volitional control and good strength were present in the biceps and brachialis muscles, the deltoid, and the trapezius. The patient underwent nerve transfers to restore finger flexion and extension, wrist flexion and extension, and elbow extension. Intraoperative motor-evoked potentials and direct nerve stimulation were used to identify donor and recipient nerve branches. Results: The patient tolerated the procedure well, with a preserved function in both elbow flexion and shoulder abduction. Conclusions: Nerve transfers are a technically feasible means of restoring the upper extremity function in tetraplegia in cases that may not be amenable to tendon transfers. PMID:21918736

Transfer function concept for ultrasonic characterization of material microstructures

NASA Technical Reports Server (NTRS)

Vary, A.; Kautz, H. E.

1986-01-01

The approach given depends on treating material microstructures as elastomechanical filters that have analytically definable transfer functions. These transfer functions can be defined in terms of the frequency dependence of the ultrasonic attenuation coefficient. The transfer function concept provides a basis for synthesizing expressions that characterize polycrystalline materials relative to microstructural factors such as mean grain size, grain-size distribution functions, and grain boundary energy transmission. Although the approach is nonrigorous, it leads to a rational basis for combining the previously mentioned diverse and fragmented equations for ultrasonic attenuation coefficients.

Reliability and Validity of the Floor Transfer Test as a Measure of Readiness for Independent Living Among Older Adults.

PubMed

Ardali, Gunay; Brody, Lori T; States, Rebecca A; Godwin, Ellen M

2017-10-20

The ability to get up from the floor after a fall is a basic skill required for functional independence. Consequently, the inability to safely get down and up from the floor or to perform a floor transfer (FT) may indicate decreased mobility and/or increased frailty. A reliable and valid test of FT ability is a critical part of the clinical decision-making process. The FT test is a simple, performance-based test that can be administered quickly and easily to determine a patient's ability to safely and successfully get down and up from the floor using any movement strategy and without time restriction. The primary purpose of this cross-sectional study was to determine the intrarater reliability and validity of the FT test as a practical alternative to several widely used yet time-consuming measures of physical disability, frailty, and functional mobility. A total of 61 community-dwelling older adults (65-96 years of age) participated in the study divided into 2 separate subsamples: 15 of them in the intrarater reliability part, while the other 46 in the concurrent validity one. In both subsamples, the participants were stratified on the basis of the self-reported levels of FT ability as independent, assisted, and dependent. Intrarater reliability was assessed in 2 separate occasions and scores were analyzed by intraclass correlation coefficient and κ statistics. Concurrent validity of the FT test was assessed against the self-reported FT ability questionnaire, Physical Functioning Scale, Phenotype of Physical Frailty, and the Short Physical Performance Battery. Known-groups validity was tested by determining whether the FT test distinguished between (1) community-dwelling older adults with physical disabilities versus those who without physical disabilities; and (2) community-dwelling older adults who were functionally dependent versus those who were independent. Participants were also categorized on the basis of FT test outcome as independent, assisted, or dependent. The Spearman correlation coefficients were calculated to examine the strength of the relationships between the FT test and physical status measures. The Kruskal-Wallis test was used to determine whether the FT test significantly discriminated between groups as categorized by the Physical Functioning Scale and Short Physical Performance Battery, and to examine the significance level of the sociodemographic data across the 3 FT test outcome groups. The intrarater reliabilities of the measures were good (0.73-1.00). There were statistically positive and strong correlations between the FT test and all physical status measures (ρ ranged from 0.86 to 0.93, P < .001). Older adults who passed the FT test were collectively categorized as those without physical disabilities and functionally independent, whereas older adults who failed the FT test were categorized as those with physical disabilities and functionally dependent (P < .001). The FT test is a reliable and valid measure for screening for physical disability, frailty, and functional mobility. It can determine which older adults have physical disabilities and/or functional dependence and hence may be useful in assessing readiness for independent living. Inclusion of the FT test at initial evaluation may reveal the presence of these conditions and address the safety of older adults in the community.

The Use of Structural-Acoustic Techniques to Assess Potential Structural Damage From Sonic Booms

NASA Technical Reports Server (NTRS)

Garrelick, Joel; Martini, Kyle

1996-01-01

The potential impact of supersonic operations includes structural damage from the sonic boom overpressure. This paper describes a study of how structural-acoustic modeling and testing techniques may be used to assess the potential for such damage in the absence of actual flyovers. Procedures are described whereby transfer functions relating structural response to sonic boom signature may be obtained with a stationary acoustic source and appropriate data processing. Further, by invoking structural-acoustic reciprocity, these transfer functions may also be acquired by measuring the radiated sound from the structure under a mechanical drive. The approach is based on the fundamental assumption of linearity, both with regard to the (acoustic) propagation of the boom in the vicinity of the structure and to the structure's response. Practical issues revolve around acoustic far field and source directivity requirements. The technique was implemented on a specially fabricated test structure at Edwards AFB, CA with the support of Wyle Laboratories, Inc. Blank shots from a cannon served as our acoustic source and taps from an instrumented hammer generated the mechanical drive. Simulated response functions were constructed. Results of comparisons with corresponding measurements recorded during dedicated supersonic flyovers with F-15 aircraft are presented for a number of sensor placements.

Can Driving-Simulator Training Enhance Visual Attention, Cognition, and Physical Functioning in Older Adults?

PubMed

Haeger, Mathias; Bock, Otmar; Memmert, Daniel; Hüttermann, Stefanie

2018-01-01

Virtual reality offers a good possibility for the implementation of real-life tasks in a laboratory-based training or testing scenario. Thus, a computerized training in a driving simulator offers an ecological valid training approach. Visual attention had an influence on driving performance, so we used the reverse approach to test the influence of a driving training on visual attention and executive functions. Thirty-seven healthy older participants (mean age: 71.46 ± 4.09; gender: 17 men and 20 women) took part in our controlled experimental study. We examined transfer effects from a four-week driving training (three times per week) on visual attention, executive function, and motor skill. Effects were analyzed using an analysis of variance with repeated measurements. Therefore, main factors were group and time to show training-related benefits of our intervention. Results revealed improvements for the intervention group in divided visual attention; however, there were benefits neither in the other cognitive domains nor in the additional motor task. Thus, there are no broad training-induced transfer effects from such an ecologically valid training regime. This lack of findings could be addressed to insufficient training intensities or a participant-induced bias following the cancelled randomization process.

Repeatability Evaluation of a Contrast Sensitivity System for Transfer to the Eye Clinic

NASA Astrophysics Data System (ADS)

Alcalde, N. G.; Castillo, L. R.; Filgueira, C. Paz; Colombo, E. M.

2016-04-01

The Contrast Sensitivity Function (CSF) is a valuable tool which can be used to characterize functional vision and also for the diagnosis and management of patients with different eye diseases. In spite of its usefulness, the CSF is currently hardly ever used in clinical practice. The aim of this study was to validate the use of the system called FVC-100 (Tecnovinc-UNT-CONICET, Argentina), which calculates the CSF, in order to transfer this important tool to ophthalmological clinics. The validation was carried out through the design of a repeatability test and the subsequent analysis of the results. Furthermore, we evaluated the impact of different factors influencing the repeatability of the measurements such as age and previous training. The tests were based on the discrimination of sinusoidal gratings for different spatial frequencies (1, 4 and 12 c/°) in both eyes of 12 people, aged between 20 and 70. The results show that the calculated values of SC of each subject have a high repeatability and are not dependent on age or training. These results allow us to conclude positively regarding the effectiveness of the FVC-100, and to validate its use in clinics for the calculation of the FSC as a standard measure of functional vision quality.

Multilayer thin-film phantoms for axial contrast transfer function measurement in optical coherence tomography.

PubMed

Agrawal, Anant; Chen, Chao-Wei; Baxi, Jigesh; Chen, Yu; Pfefer, T Joshua

2013-07-01

In optical coherence tomography (OCT), axial resolution is one of the most critical parameters impacting image quality. It is commonly measured by determining the point spread function (PSF) based on a specular surface reflection. The contrast transfer function (CTF) provides more insights into an imaging system's resolving characteristics and can be readily generated in a system-independent manner, without consideration for image pixel size. In this study, we developed a test method for determination of CTF based on multi-layer, thin-film phantoms, evaluated using spectral- and time-domain OCT platforms with different axial resolution values. Phantoms representing six spatial frequencies were fabricated and imaged. The fabrication process involved spin coating silicone films with precise thicknesses in the 8-40 μm range. Alternating layers were doped with a specified concentration of scattering particles. Validation of layer optical properties and thicknesses were achieved with spectrophotometry and stylus profilometry, respectively. OCT B-scans were used to calculate CTFs and results were compared with convetional PSF measurements based on specular reflections. Testing of these phantoms indicated that our approach can provide direct access to axial resolution characteristics highly relevant to image quality. Furthermore, tissue phantoms based on our thin-film fabrication approach may have a wide range of additional applications in optical imaging and spectroscopy.

Evaluating the integrity of the reinforced concrete structure repaired by epoxy injection using simulated transfer function of impact-echo response

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Chia-Chi; Yu, Chih-peng; Wu, Jiunn-Hong

2014-02-18

Cracks and honeycombs are often found inside reinforced concrete (RC) structure caused by excessive external force, or improper casting of concrete. The repairing method usually involves epoxy injection. The impact-echo method, which is a sensitive for detecting of the interior voids, may not be applicable to assess the integrity of the repaired member as both air and epoxy are less in acoustic impedances. In this study, the repaired RC structure was evaluated by the simulated transfer function of the IE displacement waveform where the R-wave displacement waveform is used as a base of a simulated force-time function. The effect ofmore » different thickness of the epoxy layer to the amplitude corresponding to the interface is studied by testing on specimen containing repaired naturally delaminated cracks with crack widths about 1 mm, 3 mm and 5 mm. The impact-echo responses were compared with the drilling cores at the test positions. The results showed the cracks were not fully filled with epoxy when the peak amplitude corresponding to the interface dropped less than 20%. The peak corresponding to the thicker epoxy layer tends to be larger in amplitude. A field study was also performed on a column damaged by earthquake before and after repairing.« less

VALIDATION OF BENEFIT-TRANSFER FUNCTIONS

EPA Science Inventory

1. Identification of benefit-transfer functions that are the most credible. 2. Identification of benefit-transfer issues that are related to transfer method and those related to data limitations. 3. Clarification of issues t...

Proposal of experimental setup on boiling two-phase flow on-orbit experiments onboard Japanese experiment module "KIBO"

NASA Astrophysics Data System (ADS)

Baba, S.; Sakai, T.; Sawada, K.; Kubota, C.; Wada, Y.; Shinmoto, Y.; Ohta, H.; Asano, H.; Kawanami, O.; Suzuki, K.; Imai, R.; Kawasaki, H.; Fujii, K.; Takayanagi, M.; Yoda, S.

2011-12-01

Boiling is one of the efficient modes of heat transfer due to phase change, and is regarded as promising means to be applied for the thermal management systems handling a large amount of waste heat under high heat flux. However, gravity effects on the two-phase flow phenomena and corresponding heat transfer characteristics have not been clarified in detail. The experiments onboard Japanese Experiment Module "KIBO" in International Space Station on boiling two-phase flow under microgravity conditions are proposed to clarify both of heat transfer and flow characteristics under microgravity conditions. To verify the feasibility of ISS experiments on boiling two-phase flow, the Bread Board Model is assembled and its performance and the function of components installed in a test loop are examined.

World's first telepathology experiments employing WINDS ultra-high-speed internet satellite, nicknamed “KIZUNA”

PubMed Central

Sawai, Takashi; Uzuki, Miwa; Miura, Yasuhiro; Kamataki, Akihisa; Matsumura, Tsubasa; Saito, Kenji; Kurose, Akira; Osamura, Yoshiyuki R.; Yoshimi, Naoki; Kanno, Hiroyuki; Moriya, Takuya; Ishida, Yoji; Satoh, Yohichi; Nakao, Masahiro; Ogawa, Emiko; Matsuo, Satoshi; Kasai, Hiroyuki; Kumagai, Kazuhiro; Motoda, Toshihiro; Hopson, Nathan

2013-01-01

Background: Recent advances in information technology have allowed the development of a telepathology system involving high-speed transfer of high-volume histological figures via fiber optic landlines. However, at present there are geographical limits to landlines. The Japan Aerospace Exploration Agency (JAXA) has developed the “Kizuna” ultra-high speed internet satellite and has pursued its various applications. In this study we experimented with telepathology in collaboration with JAXA using Kizuna. To measure the functionality of the Wideband InterNet working engineering test and Demonstration Satellite (WINDS) ultra-high speed internet satellite in remote pathological diagnosis and consultation, we examined the adequate data transfer speed and stability to conduct telepathology (both diagnosis and conferencing) with functionality, and ease similar or equal to telepathology using fiber-optic landlines. Materials and Methods: We performed experiments for 2 years. In year 1, we tested the usability of the WINDS for telepathology with real-time video and virtual slide systems. These are state-of-the-art technologies requiring massive volumes of data transfer. In year 2, we tested the usability of the WINDS for three-way teleconferencing with virtual slides. Facilities in Iwate (northern Japan), Tokyo, and Okinawa were connected via the WINDS and voice conferenced while remotely examining and manipulating virtual slides. Results: Network function parameters measured using ping and Iperf were within acceptable limits. However; stage movement, zoom, and conversation suffered a lag of approximately 0.8 s when using real-time video, and a delay of 60-90 s was experienced when accessing the first virtual slide in a session. No significant lag or inconvenience was experienced during diagnosis and conferencing, and the results were satisfactory. Our hypothesis was confirmed for both remote diagnosis using real-time video and virtual slide systems, and also for teleconferencing using virtual slide systems with voice functionality. Conclusions: Our results demonstrate the feasibility of ultra-high-speed internet satellite networks for use in telepathology. Because communications satellites have less geographical and infrastructural requirements than landlines, ultra-high-speed internet satellite telepathology represents a major step toward alleviating regional disparity in the quality of medical care. PMID:24244882

Real-Time Kinetic Probes Support Monothiol Glutaredoxins As Intermediate Carriers in Fe-S Cluster Biosynthetic Pathways.

PubMed

Vranish, James N; Das, Deepika; Barondeau, David P

2016-11-18

Iron-sulfur (Fe-S) clusters are protein cofactors that are required for many essential cellular functions. Fe-S clusters are synthesized and inserted into target proteins by an elaborate biosynthetic process. The insensitivity of most Fe-S assembly and transfer assays requires high concentrations for components and places major limits on reaction complexity. Recently, fluorophore labels were shown to be effective at reporting cluster content for Fe-S proteins. Here, the incorporation of this labeling approach allowed the design and interrogation of complex Fe-S cluster biosynthetic reactions that mimic in vivo conditions. A bacterial Fe-S assembly complex, composed of the cysteine desulfurase IscS and scaffold protein IscU, was used to generate [2Fe-2S] clusters for transfer to mixtures of putative intermediate carrier and acceptor proteins. The focus of this study was to test whether the monothiol glutaredoxin, Grx4, functions as an obligate [2Fe-2S] carrier protein in the Fe-S cluster distribution network. Interestingly, [2Fe-2S] clusters generated by the IscS-IscU complex transferred to Grx4 at rates comparable to previous assays using uncomplexed IscU as a cluster source in chaperone-assisted transfer reactions. Further, we provide evidence that [2Fe-2S]-Grx4 delivers clusters to multiple classes of Fe-S targets via direct ligand exchange in a process that is both dynamic and reversible. Global fits of cluster transfer kinetics support a model in which Grx4 outcompetes terminal target proteins for IscU-bound [2Fe-2S] clusters and functions as an intermediate cluster carrier. Overall, these studies demonstrate the power of chemically conjugated fluorophore reporters for unraveling mechanistic details of biological metal cofactor assembly and distribution networks.

A Randomized Controlled Trial of an Activity Specific Exercise Program for Individuals With Alzheimer Disease in Long-term Care Settings

PubMed Central

Roach, Kathryn E.; Tappen, Ruth M.; Kirk-Sanchez, Neva; Williams, Christine L.; Loewenstein, David

2011-01-01

Objective To determine whether an activity specific exercise program could improve ability to perform basic mobility activities in long-term care residents with Alzheimer disease (AD). Design Randomized, controlled, single-blinded clinical trial. Setting Residents of 7 long-term care facilities. Participants Eighty-two long-term care residents with mild to severe AD. Intervention An activity specific exercise program was compared to a walking program and to an attention control. Measurements Ability to perform bed mobility and transfers were assessed using the subscales of the Acute Care Index of Function; functional mobility was measured using the 6-Minute Walk test. Results Subjects receiving the activity specific exercise program improved in ability to perform transfers, whereas subjects in the other 2 groups declined. PMID:21937893

Optimized Signaling Method for High-Speed Transmission Channels with Higher Order Transfer Function

NASA Astrophysics Data System (ADS)

Ševčík, Břetislav; Brančík, Lubomír; Kubíček, Michal

2017-08-01

In this paper, the selected results from testing of optimized CMOS friendly signaling method for high-speed communications over cables and printed circuit boards (PCBs) are presented and discussed. The proposed signaling scheme uses modified concept of pulse width modulated (PWM) signal which enables to better equalize significant channel losses during data high-speed transmission. Thus, the very effective signaling method to overcome losses in transmission channels with higher order transfer function, typical for long cables and multilayer PCBs, is clearly analyzed in the time and frequency domain. Experimental results of the measurements include the performance comparison of conventional PWM scheme and clearly show the great potential of the modified signaling method for use in low power CMOS friendly equalization circuits, commonly considered in modern communication standards as PCI-Express, SATA or in Multi-gigabit SerDes interconnects.

Four-electron model for singlet and triplet excitation energy transfers with inclusion of coherence memory, inelastic tunneling and nuclear quantum effects

NASA Astrophysics Data System (ADS)

Suzuki, Yosuke; Ebina, Kuniyoshi; Tanaka, Shigenori

2016-08-01

A computational scheme to describe the coherent dynamics of excitation energy transfer (EET) in molecular systems is proposed on the basis of generalized master equations with memory kernels. This formalism takes into account those physical effects in electron-bath coupling system such as the spin symmetry of excitons, the inelastic electron tunneling and the quantum features of nuclear motions, thus providing a theoretical framework to perform an ab initio description of EET through molecular simulations for evaluating the spectral density and the temporal correlation function of electronic coupling. Some test calculations have then been carried out to investigate the dependence of exciton population dynamics on coherence memory, inelastic tunneling correlation time, magnitude of electronic coupling, quantum correction to temporal correlation function, reorganization energy and energy gap.

Optical properties reconstruction using the adjoint method based on the radiative transfer equation

NASA Astrophysics Data System (ADS)

Addoum, Ahmad; Farges, Olivier; Asllanaj, Fatmir

2018-01-01

An efficient algorithm is proposed to reconstruct the spatial distribution of optical properties in heterogeneous media like biological tissues. The light transport through such media is accurately described by the radiative transfer equation in the frequency-domain. The adjoint method is used to efficiently compute the objective function gradient with respect to optical parameters. Numerical tests show that the algorithm is accurate and robust to retrieve simultaneously the absorption μa and scattering μs coefficients for lowly and highly absorbing medium. Moreover, the simultaneous reconstruction of μs and the anisotropy factor g of the Henyey-Greenstein phase function is achieved with a reasonable accuracy. The main novelty in this work is the reconstruction of g which might open the possibility to image this parameter in tissues as an additional contrast agent in optical tomography.

Liver function testing on the Abaxis Piccolo Xpress: Use in Ebola virus disease protocols.

PubMed

Owen, William E; Caron, Justin E; Genzen, Jonathan R

2015-06-15

Laboratories that choose a point-of-care approach for liver function testing in patients undergoing evaluation for Ebola virus disease (EVD) have few options to choose from. The primary objective of this study was to conduct a performance characterization of a Clinical Laboratory Improvement Amendments (CLIA)-waived liver function panel on the Abaxis Piccolo® Xpress chemistry analyzer. The secondary objectives were to evaluate multiple specimen types, characterize whole blood specimen stability, and validate disposable exact transfer pipettes. Our final objective was to assess instrument airflow from a biosafety perspective. An instrument performance characterization, including precision, linearity, accuracy, reference interval verification, and specimen type evaluation was conducted using Liver Panel Plus reagent discs on the Piccolo® Xpress. All assays demonstrated acceptable linearity (slopes, 0.938-1.061; observed error, 0.8-6.3%). Assay precision was 0.0-3.6% (%CV; within-day studies) and 0.9-5.6% (between-day studies). Method comparison experiments (versus Roche cobas c502/c702 chemistry analyzers) showed excellent correlation for most assays, although a few notable differences were observed (Piccolo versus Roche): alkaline phosphatase, -18.6%; amylase, -29.0%; total bilirubin, +0.3mg/dl. Pre-programmed reference intervals were verified except for the alkaline phosphatase (male and female) and alanine aminotransferase (female), which had greater than 10% of results fall below the programmed ranges. Piccolo instrument results were largely consistent across specimen types tested (lithium-heparin whole blood, lithium-heparin plasma, and serum), although some statistical differences were observed for aspartate aminotransferase, gamma glutamyltransferase, and total protein. Whole blood time course studies demonstrated that some analytes (albumin, amylase, and total protein) showed remarkable stability, while others (such as aspartate aminotransferase) showed a slight trend toward decreased activity over time. Exact volume transfer pipettes provided an effective disposable option for disc loading. Finally, airflow studies suggested that, in the context of EVD protocols, instrument placement in a biosafety level (BSL) 2 cabinet or greater is justified. Given its analytical performance and ease of operation, the Piccolo Xpress was transferred to a BSL-2 cabinet in our BSL-3 suite for use in our hospital's diagnostic protocol for providing liver function testing in patients undergoing evaluation for EVD. Copyright © 2015 Elsevier B.V. All rights reserved.

Number of children and upstream intergenerational financial transfers: evidence from Hong Kong.

PubMed

Chou, Kee-Lee

2010-03-01

This study examined financial transfers from adult children to elderly parents in Hong Kong and tested three hypotheses about the motives for such transfers. We address previous research, suggesting that family financial support for retirees will decline in the coming decades as a consequence of the reduction in the fertility rate; we also examine whether financial transfers are a function of the number of adult children in the family. We used multiple regression models based on data from a representative sample of parents aged 60 years and older to identify the correlates of the amount of transfers from adult children to their elderly parents. We found evidence for the hypothesis that upstream transfers to elderly parents are their way of withdrawing savings from a "support bank" in which they made contribution for their children's education earlier in life and that transfers are altruistic in nature, but our results provide only moderate support to the old age security hypothesis that perceives family as a source of capital. The number of children has a ceiling effect on transfers, which calls into question common assumptions about the extent to which the decline in fertility will pose a severe threat to the extent of familial support of older persons over the coming decades.

Mitochondrial Retroprocessing Promoted Functional Transfers of rpl5 to the Nucleus in Grasses.

PubMed

Wu, Zhiqiang; Sloan, Daniel B; Brown, Colin W; Rosenblueth, Mónica; Palmer, Jeffrey D; Ong, Han Chuan

2017-09-01

Functional gene transfers from the mitochondrion to the nucleus are ongoing in angiosperms and have occurred repeatedly for all 15 ribosomal protein genes, but it is not clear why some of these genes are transferred more often than others nor what the balance is between DNA- and RNA-mediated transfers. Although direct insertion of mitochondrial DNA into the nucleus occurs frequently in angiosperms, case studies of functional mitochondrial gene transfer have implicated an RNA-mediated mechanism that eliminates introns and RNA editing sites, which would otherwise impede proper expression of mitochondrial genes in the nucleus. To elucidate the mechanisms that facilitate functional gene transfers and the evolutionary dynamics of the coexisting nuclear and mitochondrial gene copies that are established during these transfers, we have analyzed rpl5 genes from 90 grasses (Poaceae) and related monocots. Multiple lines of evidence indicate that rpl5 has been functionally transferred to the nucleus at least three separate times in the grass family and that at least seven species have intact and transcribed (but not necessarily functional) copies in both the mitochondrion and nucleus. In two grasses, likely functional nuclear copies of rpl5 have been subject to recent gene conversion events via secondarily transferred mitochondrial copies in what we believe are the first described cases of mitochondrial-to-nuclear gene conversion. We show that rpl5 underwent a retroprocessing event within the mitochondrial genome early in the evolution of the grass family, which we argue predisposed the gene towards successful, DNA-mediated functional transfer by generating a "pre-edited" sequence. © The Author 2017. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Fast computation of the electrolyte-concentration transfer function of a lithium-ion cell model

NASA Astrophysics Data System (ADS)

Rodríguez, Albert; Plett, Gregory L.; Trimboli, M. Scott

2017-08-01

One approach to creating physics-based reduced-order models (ROMs) of battery-cell dynamics requires first generating linearized Laplace-domain transfer functions of all cell internal electrochemical variables of interest. Then, the resulting infinite-dimensional transfer functions can be reduced by various means in order to find an approximate low-dimensional model. These methods include Padé approximation or the Discrete-Time Realization algorithm. In a previous article, Lee and colleagues developed a transfer function of the electrolyte concentration for a porous-electrode pseudo-two-dimensional lithium-ion cell model. Their approach used separation of variables and Sturm-Liouville theory to compute an infinite-series solution to the transfer function, which they then truncated to a finite number of terms for reasons of practicality. Here, we instead use a variation-of-parameters approach to arrive at a different representation of the identical solution that does not require a series expansion. The primary benefits of the new approach are speed of computation of the transfer function and the removal of the requirement to approximate the transfer function by truncating the number of terms evaluated. Results show that the speedup of the new method can be more than 3800.

The transfer functions of cardiac tissue during stochastic pacing.

PubMed

de Lange, Enno; Kucera, Jan P

2009-01-01

The restitution properties of cardiac action potential duration (APD) and conduction velocity (CV) are important factors in arrhythmogenesis. They determine alternans, wavebreak, and the patterns of reentrant arrhythmias. We developed a novel approach to characterize restitution using transfer functions. Transfer functions relate an input and an output quantity in terms of gain and phase shift in the complex frequency domain. We derived an analytical expression for the transfer function of interbeat intervals (IBIs) during conduction from one site (input) to another site downstream (output). Transfer functions can be efficiently obtained using a stochastic pacing protocol. Using simulations of conduction and extracellular mapping of strands of neonatal rat ventricular myocytes, we show that transfer functions permit the quantification of APD and CV restitution slopes when it is difficult to measure APD directly. We find that the normally positive CV restitution slope attenuates IBI variations. In contrast, a negative CV restitution slope (induced by decreasing extracellular [K(+)]) amplifies IBI variations with a maximum at the frequency of alternans. Hence, it potentiates alternans and renders conduction unstable, even in the absence of APD restitution. Thus, stochastic pacing and transfer function analysis represent a powerful strategy to evaluate restitution and the stability of conduction.

Lunar-edge based on-orbit modulation transfer function (MTF) measurement

NASA Astrophysics Data System (ADS)

Cheng, Ying; Yi, Hongwei; Liu, Xinlong

2017-10-01

Modulation transfer function (MTF) is an important parameter for image quality evaluation of on-orbit optical image systems. Various methods have been proposed to determine the MTF of an imaging system which are based on images containing point, pulse and edge features. In this paper, the edge of the moon can be used as a high contrast target to measure on-orbit MTF of image systems based on knife-edge methods. The proposed method is an extension of the ISO 12233 Slanted-edge Spatial Frequency Response test, except that the shape of the edge is a circular arc instead of a straight line. In order to get more accurate edge locations and then obtain a more authentic edge spread function (ESF), we choose circular fitting method based on least square to fit lunar edge in sub-pixel edge detection process. At last, simulation results show that the MTF value at Nyquist frequency calculated using our lunar edge method is reliable and accurate with error less than 2% comparing with theoretical MTF value.

Host-derived transferrin is maintained and transferred from midgut to ovary in Haemaphysalis longicornis ticks.

PubMed

Mori, Hiroyuki; Galay, Remil Linggatong; Maeda, Hiroki; Matsuo, Tomohide; Umemiya-Shirafuji, Rika; Mochizuki, Masami; Fujisaki, Kozo; Tanaka, Tetsuya

2014-03-01

Transferrin is known to be an iron transporter in vertebrates and several arthropods. Iron from host blood is essential for ovarian development in blood-sucking arthropods. However, tick transferrin has been identified in only a few species, and its function has yet to be elucidated, resulting in incomplete understanding of iron metabolism in ticks. Here, we investigated the transfer of host-derived transferrin in the hard tick Haemaphysalis longicornis using immunological methods. Western blot showed that host-derived transferrin was maintained in all developmental stages of ticks up to 28 days after engorgement and was detected in the midgut and the ovary of adult females following blood feeding. However, no host-derived transferrin was detected in eggs after laying or in larvae after hatching, indicating that host-derived transferrin is not transferred to offspring transovarially. Indirect immunofluorescent antibody testing showed the localization of host-derived transferrin in digestive cells of the midgut and oocytes of the ovary from engorged adult females. These results suggest that host-derived transferrin is transferred to the ovary through the midgut and the hemolymph, and raise the possibility of the function of host-derived transferrin as an iron source in the ovary, providing additional insight on iron metabolism in ticks. Copyright © 2013 Elsevier GmbH. All rights reserved.

"Self-Peel-Off" Transfer Produces Ultrathin Polyvinylidene-Fluoride-Based Flexible Nanodevices.

PubMed

Tai, Yanlong; Lubineau, Gilles

2017-04-01

Here, a new strategy, self-peel-off transfer, for the preparation of ultrathin flexible nanodevices made from polyvinylidene-fluoride (PVDF) is reported. In this process, a functional pattern of nanoparticles is transferred via peeling from a temporary substrate to the final PVDF film. This peeling process takes advantage of the differences in the work of adhesion between the various layers (the PVDF layer, the nanoparticle-pattern layer and the substrate layer) and of the high stresses generated by the differential thermal expansion of the layers. The work of adhesion is mainly guided by the basic physical/chemical properties of these layers and is highly sensitive to variations in temperature and moisture in the environment. The peeling technique is tested on a variety of PVDF-based functional films using gold/palladium nanoparticles, carbon nanotubes, graphene oxide, and lithium iron phosphate. Several PVDF-based flexible nanodevices are prepared, including a single-sided wireless flexible humidity sensor in which PVDF is used as the substrate and a double-sided flexible capacitor in which PVDF is used as the ferroelectric layer and the carrier layer. Results show that the nanodevices perform with high repeatability and stability. Self-peel-off transfer is a viable preparation strategy for the design and fabrication of flexible, ultrathin, and light-weight nanodevices.

Accelerated Testing and Modeling of Potential-Induced Degradation as a Function of Temperature and Relative Humidity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hacke, Peter; Spataru, Sergiu; Terwilliger, Kent

2015-06-14

An acceleration model based on the Peck equation was applied to power performance of crystalline silicon cell modules as a function of time and of temperature and humidity, the two main environmental stress factors that promote potential-induced degradation. This model was derived from module power degradation data obtained semi-continuously and statistically by in-situ dark current-voltage measurements in an environmental chamber. The modeling enables prediction of degradation rates and times as functions of temperature and humidity. Power degradation could be modeled linearly as a function of time to the second power; additionally, we found that coulombs transferred from the active cellmore » circuit to ground during the stress test is approximately linear with time. Therefore, the power loss could be linearized as a function of coulombs squared. With this result, we observed that when the module face was completely grounded with a condensed phase conductor, leakage current exceeded the anticipated corresponding degradation rate relative to the other tests performed in damp heat.« less

Applications of aerospace technology in industry: A technology transfer profile, nondestructive testing

NASA Technical Reports Server (NTRS)

1972-01-01

The development of nondestructive testing procedures by NASA and the transfer of nondestructive testing to technology to civilian industry are discussed. The subjects presented are: (1) an overview of the nondestructive testing field, (2) NASA contributions to the field of nondestructive testing, (3) dissemination of NASA contributions, and (4) a transfer profile. Attachments are included which provide a brief description of common nondestructive testing methods and summarize the technology transfer reports involving NASA generated nondestructive testing technology.

Microparticle-mediated transfer of the viral receptors CAR and CD46, and the CFTR channel in a CHO cell model confers new functions to target cells.

PubMed

Gonzalez, Gaëlle; Vituret, Cyrielle; Di Pietro, Attilio; Chanson, Marc; Boulanger, Pierre; Hong, Saw-See

2012-01-01

Cell microparticles (MPs) released in the extracellular milieu can embark plasma membrane and intracellular components which are specific of their cellular origin, and transfer them to target cells. The MP-mediated, cell-to-cell transfer of three human membrane glycoproteins of different degrees of complexity was investigated in the present study, using a CHO cell model system. We first tested the delivery of CAR and CD46, two monospanins which act as adenovirus receptors, to target CHO cells. CHO cells lack CAR and CD46, high affinity receptors for human adenovirus serotype 5 (HAdV5), and serotype 35 (HAdV35), respectively. We found that MPs derived from CHO cells (MP-donor cells) constitutively expressing CAR (MP-CAR) or CD46 (MP-CD46) were able to transfer CAR and CD46 to target CHO cells, and conferred selective permissiveness to HAdV5 and HAdV35. In addition, target CHO cells incubated with MP-CD46 acquired the CD46-associated function in complement regulation. We also explored the MP-mediated delivery of a dodecaspanin membrane glycoprotein, the CFTR to target CHO cells. CFTR functions as a chloride channel in human cells and is implicated in the genetic disease cystic fibrosis. Target CHO cells incubated with MPs produced by CHO cells constitutively expressing GFP-tagged CFTR (MP-GFP-CFTR) were found to gain a new cellular function, the chloride channel activity associated to CFTR. Time-course analysis of the appearance of GFP-CFTR in target cells suggested that MPs could achieve the delivery of CFTR to target cells via two mechanisms: the transfer of mature, membrane-inserted CFTR glycoprotein, and the transfer of CFTR-encoding mRNA. These results confirmed that cell-derived MPs represent a new class of promising therapeutic vehicles for the delivery of bioactive macromolecules, proteins or mRNAs, the latter exerting the desired therapeutic effect in target cells via de novo synthesis of their encoded proteins.

Exploring the limit of accuracy for density functionals based on the generalized gradient approximation: Local, global hybrid, and range-separated hybrid functionals with and without dispersion corrections

DOE PAGES

Mardirossian, Narbe; Head-Gordon, Martin

2014-03-25

The limit of accuracy for semi-empirical generalized gradient approximation (GGA) density functionals is explored in this paper by parameterizing a variety of local, global hybrid, and range-separated hybrid functionals. The training methodology employed differs from conventional approaches in 2 main ways: (1) Instead of uniformly truncating the exchange, same-spin correlation, and opposite-spin correlation functional inhomogeneity correction factors, all possible fits up to fourth order are considered, and (2) Instead of selecting the optimal functionals based solely on their training set performance, the fits are validated on an independent test set and ranked based on their overall performance on the trainingmore » and test sets. The 3 different methods of accounting for exchange are trained both with and without dispersion corrections (DFT-D2 and VV10), resulting in a total of 491 508 candidate functionals. For each of the 9 functional classes considered, the results illustrate the trade-off between improved training set performance and diminished transferability. Since all 491 508 functionals are uniformly trained and tested, this methodology allows the relative strengths of each type of functional to be consistently compared and contrasted. Finally, the range-separated hybrid GGA functional paired with the VV10 nonlocal correlation functional emerges as the most accurate form for the present training and test sets, which span thermochemical energy differences, reaction barriers, and intermolecular interactions involving lighter main group elements.« less

Extracting electron transfer coupling elements from constrained density functional theory

NASA Astrophysics Data System (ADS)

Wu, Qin; Van Voorhis, Troy

2006-10-01

Constrained density functional theory (DFT) is a useful tool for studying electron transfer (ET) reactions. It can straightforwardly construct the charge-localized diabatic states and give a direct measure of the inner-sphere reorganization energy. In this work, a method is presented for calculating the electronic coupling matrix element (Hab) based on constrained DFT. This method completely avoids the use of ground-state DFT energies because they are known to irrationally predict fractional electron transfer in many cases. Instead it makes use of the constrained DFT energies and the Kohn-Sham wave functions for the diabatic states in a careful way. Test calculations on the Zn2+ and the benzene-Cl atom systems show that the new prescription yields reasonable agreement with the standard generalized Mulliken-Hush method. We then proceed to produce the diabatic and adiabatic potential energy curves along the reaction pathway for intervalence ET in the tetrathiafulvalene-diquinone (Q-TTF-Q) anion. While the unconstrained DFT curve has no reaction barrier and gives Hab≈17kcal /mol, which qualitatively disagrees with experimental results, the Hab calculated from constrained DFT is about 3kcal /mol and the generated ground state has a barrier height of 1.70kcal/mol, successfully predicting (Q-TTF-Q)- to be a class II mixed-valence compound.

Transfer of training between distinct motor tasks after stroke: Implications for task- specific approaches to upper extremity neurorehabilitation

PubMed Central

Schaefer, Sydney Y.; Patterson, Chavelle B.; Lang, Catherine E.

2013-01-01

Background Although task-specific training is emerging as a viable approach for recovering motor function after stroke, there is little evidence for whether the effects of such training transfer to other functional motor tasks not directly practiced in therapy. Objective The purpose of the current study was to test whether training on one motor task would transfer to untrained tasks that were either spatiotemporally similar or different in individuals with chronic hemiparesis post-stroke. Methods Eleven participants with chronic mild-to-moderate hemiparesis following stroke completed five days of supervised massed practice of a feeding task with their affected side. Performance on the feeding task, along with two other untrained functional upper extremity motor tasks (sorting, dressing) was assessed before and after training. Results Performance of all three tasks improved significantly after training exclusively on one motor task. The amount of improvement in the untrained tasks was comparable, and was not dependent on the degree of similarity to the trained task. Conclusions Because the number and type of tasks that can be practiced are often limited within standard stroke rehabilitation, results from this study will be useful for designing task-specific training plans to maximize therapy benefits. PMID:23549521

Imaging quality analysis of multi-channel scanning radiometer

NASA Astrophysics Data System (ADS)

Fan, Hong; Xu, Wujun; Wang, Chengliang

2008-03-01

Multi-channel scanning radiometer, on boarding FY-2 geostationary meteorological satellite, plays a key role in remote sensing because of its wide field of view and continuous multi-spectral images acquirements. It is significant to evaluate image quality after performance parameters of the imaging system are validated. Several methods of evaluating imaging quality are discussed. Of these methods, the most fundamental is the MTF. The MTF of photoelectric scanning remote instrument, in the scanning direction, is the multiplication of optics transfer function (OTF), detector transfer function (DTF) and electronics transfer function (ETF). For image motion compensation, moving speed of scanning mirror should be considered. The optical MTF measurement is performed in both the EAST/WEST and NORTH/SOUTH direction, whose values are used for alignment purposes and are used to determine the general health of the instrument during integration and testing. Imaging systems cannot perfectly reproduce what they see and end up "blurring" the image. Many parts of the imaging system can cause blurring. Among these are the optical elements, the sampling of the detector itself, post-processing, or the earth's atmosphere for systems that image through it. Through theory calculation and actual measurement, it is proved that DTF and ETF are the main factors of system MTF and the imaging quality can satisfy the requirement of instrument design.

Treatment of peroneal nerve injuries with simultaneous tendon transfer and nerve exploration.

PubMed

Ho, Bryant; Khan, Zubair; Switaj, Paul J; Ochenjele, George; Fuchs, Daniel; Dahl, William; Cederna, Paul; Kung, Theodore A; Kadakia, Anish R

2014-08-06

Common peroneal nerve palsy leading to foot drop is difficult to manage and has historically been treated with extended bracing with expectant waiting for return of nerve function. Peroneal nerve exploration has traditionally been avoided except in cases of known traumatic or iatrogenic injury, with tendon transfers being performed in a delayed fashion after exhausting conservative treatment. We present a new strategy for management of foot drop with nerve exploration and concomitant tendon transfer. We retrospectively reviewed a series of 12 patients with peroneal nerve palsies that were treated with tendon transfer from 2005 to 2011. Of these patients, seven were treated with simultaneous peroneal nerve exploration and repair at the time of tendon transfer. Patients with both nerve repair and tendon transfer had superior functional results with active dorsiflexion in all patients, compared to dorsiflexion in 40% of patients treated with tendon transfers alone. Additionally, 57% of patients treated with nerve repair and tendon transfer were able to achieve enough function to return to running, compared to 20% in patients with tendon transfer alone. No patient had full return of native motor function resulting in excessive dorsiflexion strength. The results of our limited case series for this rare condition indicate that simultaneous nerve repair and tendon transfer showed no detrimental results and may provide improved function over tendon transfer alone.

Synthesis of Natural Electric and Magnetic Time Series Using Impulse Responses of Inter-station Transfer Functions and a Reference

NASA Astrophysics Data System (ADS)

Wang, H.; Cheng, J.

2017-12-01

A method to Synthesis natural electric and magnetic Time series is proposed whereby the time series of local site are derived using an Impulse Response and a reference (STIR). The method is based on the assumption that the external source of magnetic fields are uniform, and the electric and magnetic fields acquired at the surface satisfy a time-independent linear relation in frequency domain.According to the convolution theorem, we can synthesize natural electric and magnetic time series using the impulse responses of inter-station transfer functions with a reference. Applying this method, two impulse responses need to be estimated: the quasi-MT impulse response tensor and the horizontal magnetic impulse response tensor. These impulse response tensors relate the local horizontal electric and magnetic components with the horizontal magnetic components at a reference site, respectively. Some clean segments of times series are selected to estimate impulse responses by using least-square (LS) method. STIR is similar with STIN (Wang, 2017), but STIR does not need to estimate the inter-station transfer functions, and the synthesized data are more accurate in high frequency, where STIN fails when the inter-station transfer functions are contaminated severely. A test with good quality of MT data shows that synthetic time-series are similar to natural electric and magnetic time series. For contaminated AMT example, when this method is used to remove noise present at the local site, the scatter of MT sounding curves are clear reduced, and the data quality are improved. *This work is funded by National Key R&D Program of China(2017YFC0804105),National Natural Science Foundation of China (41604064, 51574250), State Key Laboratory of Coal Resources and Safe Mining ,China University of Mining & Technology,(SKLCRSM16DC09)

Nerve Transfers for Improved Hand Function Following Cervical Spinal Cord Injury

DTIC Science & Technology

the cervical spine resulting in diminished or complete loss of arm and/or hand function. Cervical SCI patients consistently rank hand function as the...most desired function above bowel and bladder function, sexual function, standing, and pain control. The overall goal of the proposed study is to...evaluate the efficacy of nerve transfers to treat patients with cervical SCIs. Over the last decade, nerve transfers have been used with increasing

The effect of electromagnetic interference from mobile communication on the performance of intensive care ventilators.

PubMed

Jones, R P; Conway, D H

2005-08-01

Electromagnetic interference produced by wireless communication can affect medical devices and hospital policies exist to address this risk. During the transfer of ventilated patients, these policies may be compromised by essential communication between base and receiving hospitals. Local wireless networks (e.g. Bluetooth) may reduce the 'spaghetti syndrome' of wires and cables seen on intensive care units, but also generate electromagnetic interference. The aim of this study was to investigate these effects on displayed and actual ventilator performance. Five ventilators were tested: Drager Oxylog 2000, BREAS LTV-1000, Respironics BiPAP VISION, Puritan Bennett 7200 and 840. Electromagnetic interference was generated by three devices: Simoco 8020 radio handset, Nokia 7210 and Nokia 6230 mobile phone, Nokia 6230 communicating via Bluetooth with a Palm Tungsten T Personal Digital Assistant. We followed the American National Standard Recommended Practice for On-Site, Ad Hoc Testing (ANSI C63) for electromagnetic interference. We used a ventilator tester, to simulate healthy adult lungs and measure ventilator performance. The communication device under test was moved in towards each ventilator from a distance of 1 m in six axes. Alarms or error codes on the ventilator were recorded, as was ventilator performance. All ventilators tested, except for the Respironics VISION, showed a display error when subjected to electromagnetic interference from the Nokia phones and Simoco radio. Ventilator performance was only affected by the radio which caused the Puritan Bennett 840 to stop functioning completely. The transfer ventilators' performance were not affected by radio or mobile phone, although the mobile phone did trigger a low-power alarm. Effects on intensive care ventilators included display reset, with the ventilator restoring normal display function within 2 s, and low-power/low-pressure alarms. Bluetooth transmission had no effect on the function of all the ventilators tested. In a clinical setting, high-power-output devices such as a two-way radio may cause significant interference in ventilator function. Medium-power-output devices such as mobile phones may cause minor alarm triggers. Low-power-output devices such as Bluetooth appear to cause no interference with ventilator function.

Influence of acoustic impedance of multilayer acoustic systems on the transfer function of ultrasonic airborne transducers.

PubMed

Gudra, Tadeusz; Opieliński, Krzysztof J

2002-05-01

In different solutions of ultrasonic transducers radiating acoustic energy into the air there occurs the problem of the proper selection of the acoustic impedance of one or more matching layers. The goal of this work was a computer analysis of the influence of acoustic impedance on the transfer function of piezoceramic transducers equipped with matching layers. Cases of resonance and non-resonance matching impedance in relation to the transfer function and the energy transmission coefficient for solid state-air systems were analysed. With stable thickness of matching layers the required shape of the transfer function can be obtained through proper choice of acoustic impedance were built (e.g. maximal flat function). The proper choice of acoustic impedance requires an elaboration of precise methods of synthesis of matching systems. Using the known matching criteria (Chebyshev's, DeSilets', Souquet's), the transfer function characteristics of transducers equipped with one, two, and three matching layers as well as the optimisation methods of the energy transmission coefficient were presented. The influence of the backside load of the transducer on the shape of transfer function was also analysed. The calculation results of this function for different loads of the transducer backside without and with the different matching layers were presented. The proper load selection allows us to obtain the desired shape of the transfer function, which determines the pulse shape generated by the transducer.

Significance of a Recurring Function in Energy Transfer

NASA Astrophysics Data System (ADS)

Mishra, Subodha

2017-05-01

The appearance of a unique function in the energy transfer from one system to the other in different physical situations such as electrical, mechanical, optical, and quantum mechanical processes is established in this work. Though the laws governing the energy transformation and its transfer from system to system are well known, here we notice a unity in diversity; a unique function appears in various cases of energy transfer whether it is a classical or a quantum mechanical process. We consider four examples, well known in elementary physics, from the fields of electricity, mechanics, optics, and quantum mechanics. We find that this unique function is in fact the transfer function corresponding to all these physical situations, and the interesting and intriguing finding is that the inverse Laplace transform of this transfer function, which is the impulse-response function of the systems when multiplied by a factor of -½, is the solution of a linear differential equation for an "instantly forced critically damped harmonic oscillator." It is important to note that though the physical phenomena considered are quite distinct, the underlying process in the language of impulse-response of the system in the time domain is a unique one. To the best of our knowledge we have not seen anywhere the above analysis of determining the unique function or its description as a transfer function in literature.

Using nerve transfer to restore prehension and grasp 12 years following spinal cord injury: a case report.

PubMed

Fox, Ida K; Novak, Christine B; Kahn, Lorna C; Mackinnon, Susan E; Ruvinskaya, Rimma; Juknis, Neringa

2018-01-01

Nerve transfers are used routinely for reconstruction of hand function following lower motor neuron lesions. In people with cervical spinal cord injury (SCI), this novel and alternate reconstruction option may be useful to restore prehension and grasp, and improve hand function. A 34-year-old male presented 12 years post-mid-cervical SCI. Pre-operative electrodiagnostic studies revealed intact lower motor neurons below the SCI level. He elected to undergo nerve transfer surgery to restore hand function. Intraoperative evaluation led to the transfer of a brachialis nerve to several median nerve recipient branches. Post surgery, he was discharged home and resumed activities of daily living. He achieved independent thumb and finger flexion function and continued to exhibit functional improvement at 4 years post surgery. These results should prompt referral for consideration of nerve transfer surgery-an exciting alternative to tendon transfer and neuroprostheses.

A functional electrical stimulation system for human walking inspired by reflexive control principles.

PubMed

Meng, Lin; Porr, Bernd; Macleod, Catherine A; Gollee, Henrik

2017-04-01

This study presents an innovative multichannel functional electrical stimulation gait-assist system which employs a well-established purely reflexive control algorithm, previously tested in a series of bipedal walking robots. In these robots, ground contact information was used to activate motors in the legs, generating a gait cycle similar to that of humans. Rather than developing a sophisticated closed-loop functional electrical stimulation control strategy for stepping, we have instead utilised our simple reflexive model where muscle activation is induced through transfer functions which translate sensory signals, predominantly ground contact information, into motor actions. The functionality of the functional electrical stimulation system was tested by analysis of the gait function of seven healthy volunteers during functional electrical stimulation-assisted treadmill walking compared to unassisted walking. The results demonstrated that the system was successful in synchronising muscle activation throughout the gait cycle and was able to promote functional hip and ankle movements. Overall, the study demonstrates the potential of human-inspired robotic systems in the design of assistive devices for bipedal walking.

Designs and test results for three new rotational sensors

USGS Publications Warehouse

Jedlicka, P.; Kozak, J.T.; Evans, J.R.; Hutt, C.R.

2012-01-01

We discuss the designs and testing of three rotational seismometer prototypes developed at the Institute of Geophysics, Academy of Sciences (Prague, Czech Republic). Two of these designs consist of a liquid-filled toroidal tube with the liquid as the proof mass and providing damping; we tested the piezoelectric and pressure transduction versions of this torus. The third design is a wheel-shaped solid metal inertial sensor with capacitive sensing and magnetic damping. Our results from testing in Prague and at the Albuquerque Seismological Laboratory of the US Geological Survey of transfer function and cross-axis sensitivities are good enough to justify the refinement and subsequent testing of advanced prototypes. These refinements and new testing are well along.

Rocket Propulsion 21 Steering Committee Meeting (RP21) NASA In-Space Propulsion Update

NASA Technical Reports Server (NTRS)

Klem, Mark

2015-01-01

In-house Support of NEXT-C Contract Status Thruster NEXT Long Duration Test post-test destructive evaluation in progress Findings will be used to verify service life models identify potential design improvements Cathode heater fabrication initiated for cyclic life testing Thruster operating algorithm definition verification initiated to provide operating procedures for mission users High voltage propellant isolator life test voluntarily terminated after successfully operating 51,200 h Power processor unit (PPU) Replaced all problematic stacked multilayer ceramic dual inline pin capacitors within PPU Test bed Rebuilt installed discharge power supply primary power board Completed full functional performance characterization Final test report in progress Transferred PPU Testbed to contractor to support prototype design effort.

Designs and test results for three new rotational sensors

NASA Astrophysics Data System (ADS)

Jedlička, P.; Kozák, J. T.; Evans, J. R.; Hutt, C. R.

2012-10-01

We discuss the designs and testing of three rotational seismometer prototypes developed at the Institute of Geophysics, Academy of Sciences (Prague, Czech Republic). Two of these designs consist of a liquid-filled toroidal tube with the liquid as the proof mass and providing damping; we tested the piezoelectric and pressure transduction versions of this torus. The third design is a wheel-shaped solid metal inertial sensor with capacitive sensing and magnetic damping. Our results from testing in Prague and at the Albuquerque Seismological Laboratory of the US Geological Survey of transfer function and cross-axis sensitivities are good enough to justify the refinement and subsequent testing of advanced prototypes. These refinements and new testing are well along.

Development of a Gene Cloning System in Methanogens.

DTIC Science & Technology

1987-03-27

Genetic transfer via DNA-dependent natural transformation was achieved for two markers, 5-fluorouracil-resistance, and 6- mercaptopurine resistance...resistance genes, and genes coding for enzymes that produce colored products will be tested as markers for plasmid transformation. A functional plasmid...clones, which include resistances to mercaptopurine , azahypoxanthine, diazauracil, kanamycin, mitomycin C, and fluorouracil- mercaptopurine and

USGS VDP Infrasound Sensor Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slad, George William; Merchant, Bion J.

2016-10-01

Sandia National Laboratories has tested and evaluated two infrasound sensors, the model VDP100 and VDP250, built in-house at the USGS Cascades Volcano Observatory. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, self-noise, dynamic range and nominal transfer function. Notable features of the VDP sensors include novel and durable construction and compact size.

Effects of Consecutive Wideband Tympanometry Trials on Energy Absorbance Measures of the Middle Ear

ERIC Educational Resources Information Center

Burdiek, Laina M.; Sun, Xiao-Ming

2014-01-01

Purpose: Wideband acoustic immittance (WAI) is a new technique for assessing middle ear transfer function. It includes energy absorbance (EA) measures and can be acquired with the ear canal pressure varied, known as "wideband tympanometry" (WBTymp). The authors of this study aimed to investigate effects of consecutive WBTymp testing on…

Learning from Scientific Texts: Personalizing the Text Increases Transfer Performance and Task Involvement

ERIC Educational Resources Information Center

Dutke, Stephan; Grefe, Anna Christina; Leopold, Claudia

2016-01-01

In an experiment with 65 high-school students, we tested the hypothesis that personalizing learning materials would increase students' learning performance and motivation to study the learning materials. Students studied either a 915-word standard text on the anatomy and functionality of the human eye or a personalized version of the same text in…

An exploration of exercise-induced cognitive enhancement and transfer effects to dietary self-control.

PubMed

Lowe, Cassandra J; Kolev, Dimitar; Hall, Peter A

2016-12-01

The primary objective of this study was to examine the effects of aerobic exercise on executive function, specifically inhibitory control, and the transfer to self-control in the dietary domain. It was hypothesized that exercise would enhance inhibitory control, and that this enhancement would facilitate self-control in a laboratory taste test paradigm. Using a crossover design, 51 participants completed counterbalanced sessions of both moderate exercise (experimental condition) and minimal effort walking (control condition) using a treadmill; the intersession interval was 7days. Prior to each exercise bout participants completed a Stroop task. Following each bout participants completed a second Stoop task, as well as a bogus taste test involving three appetitive calorie dense snack foods and two control foods; the amount of each food type consumed during the taste test was covertly measured. Results revealed that moderate exercise significantly improved performance on the Stroop task, and also reduced food consumption during the taste test for appetitive calorie dense snack foods; there was no exercise effect on control food consumption. Exercise-induced gains in Stroop performance mediated the effects of moderate exercise on appetitive snack food consumption. Together these findings provide evidence that a bout of a moderate aerobic exercise can enhance inhibitory control, and support for cross-domain transfer effects to dietary self-control. Copyright © 2016 Elsevier Inc. All rights reserved.

Understanding the Importance of the Teres Minor for Shoulder Function: Functional Anatomy and Pathology.

PubMed

Williams, Matthew D; Edwards, Thomas Bradley; Walch, Gilles

2018-03-01

Although the teres minor is often overlooked in a normal shoulder, it becomes a key component in maintaining shoulder function when other rotator cuff tendons fail. The teres minor maintains a balanced glenohumeral joint and changes from an insignificant to the most significant external rotator in the presence of major rotator cuff pathology. The presence or absence of the teres minor provides prognostic information on the outcomes of reverse total shoulder arthroplasty and tendon transfers. Clinical tests include the Patte test, the Neer dropping sign, the external rotation lag sign, and the Hertel drop sign. Advanced imaging of the teres minor can be used for classification using the Walch system. Understanding the function and pathology surrounding the teres minor is paramount in comprehensive management of the patient with shoulder pathology. Appropriate clinical examination and imaging of the teres minor are important for preoperative stratification and postoperative expectations.

Simple and easy assessment of falling risk in the elderly by functional reach test using elastic stick.

PubMed

Demura, Shin-Ichi; Yamada, Takayoshi

2007-10-01

Dynamic balance ability related to maintaining postural stability during movement is closely tied to fall risk in the elderly. The functional reach (FR) test has been developed to evaluate their dynamic balance. Although a simple and new FR test using an elastic stick has been proposed by modifying the above original FR test, the abilities related to both FR tests are judged to differ because of the large difference in the testing method. This study aimed to compare center of gravity fluctuation, muscle activity and functional reach distance as measured by the original FR test and the elastic stick FR test. First, reach distance, back/forth and right/left moving distance of the center of gravity, and activity of the lower leg muscles (soleus and tibialis anterior) were compared between both tests based on data obtained from 30 young male adults. All parameters except for the right/left moving distance were significantly larger in the elastic stick FR test. Next, the reach distance was examined in both FR tests using 53 elderly subjects; it was significantly longer in the elastic stick FR test, but showed no significant sex difference. The reach distance in both tests was significantly shorter (about 7 cm) in the elderly than in young adults. In conclusion, the elastic stick FR test involves greater leg muscle strength exertion and forward transferring of the center of gravity as compared with the original FR test. Because the elastic stick FR test relates largely to leg muscle function and equilibrium function, it may be more useful for evaluating the dynamic balance ability of the elderly.

Test results of the STI GPS time transfer receiver

NASA Technical Reports Server (NTRS)

Hall, D. L.; Handlan, J.; Wheeler, P.

1983-01-01

Global time transfer, or synchronization, between a user clock and USNO UTC time can be performed using the Global Positioning System (GPS), and commercially available time transfer receivers. This paper presents the test results of time transfer using the GPS system and a Stanford Telecommunications, Inc. (STI) Time Transfer System (TTS) Model 502. Tests at the GPS Master Control Site (MCS) in Vandenburg, California and at the United States Naval Observatory (USNO) in Washington, D.C. are described. An overview of GPS, and the STI TTS 502 is presented. A discussion of the time transfer process and test concepts is included.

Hyperion 5113/A Infrasound Sensor Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion John

2015-09-01

Sandia National Laboratories has tested and evaluated an infrasound sensor, the 5113/A manufactured by Hyperion. These infrasound sensors measure pressure output by a methodology developed by the University of Mississippi. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, transfer function, power, self-noise, and dynamic range. The 5113/A infrasound sensor is a new revision of the 5000 series intended to meet the infrasound application requirements for use in the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO).

Development of a Dynamic Visco-elastic Vehicle-Soil Interaction Model for Rut Depth, and Power Determinations

DTIC Science & Technology

2011-09-06

Presentation Outline A) Review of Soil Model governing equations B) Development of pedo -transfer functions (terrain database to engineering properties) C...lateral earth pressure) UNCLASSIFIED B) Development of pedo -transfer functions Engineering parameters needed by soil model - compression index - rebound...inches, RCI for fine- grained soils, CI for coarse-grained soils. UNCLASSIFIED Pedo -transfer function • Need to transfer existing terrain database

Adaptive Same Frequency Repeater (SFR) Study

DTIC Science & Technology

1976-03-01

Formulation 13 (2) Evaluation of the Steady State Weights!.’.’.’!.*!!."!! 21 (3) Evaluation of the Composite Transfer Function.... 2^ (4) Simplified...well as possible the amplitude and phase of the composite coupling path. Because the coupling paths have frequency-dependent transfer functions...34), (35) and the notch filter and channel transfer .’unctions (3fi) and (39). The composite transfer function Hc(f ’ ^’.f) is then found and

Postoperative physical therapy program for latissimus dorsi and teres major tendons transfer to rotator cuff in children with obstetrical brachial plexus injury.

PubMed

Safoury, Yasser A; Eldesoky, Mohamed T; Abutaleb, Enas E; Atteya, Mohamed R; Gabr, Ahmed M

2017-04-01

The transfer of latissimus dorsi and teres major tendons to rotator cuff have been developed to rebalance the muscular dysfunction and improve shoulder range of motion in children with obstetrical brachial plexus palsy (OBPP). No previous study reported the ideal postoperative physical therapy program for these cases. The aim of the present study was to design appropriate postoperative physical therapy (PT) program after latissimus dorsi and teres major tendons transfer to rotator cuff in OBPP to improve upper limb function. Time series design. The patients were recruited from outpatient clinic of Kasr EL Aini Hospital, Cairo, Egypt. Forty seven OBPP infants (4.64±1.21 years with a range of 2.5 to 7 years, 21male and26 female) were allocated to one group. All patients had functional limitation in the involved arm due to muscle paralysis and contracture. Twenty-five patients had C5-C6 nerve root lesions while 22 had C5-C6-C7 nerve root lesions. The children underwent the surgical procedures of the transfer of latissimus dorsi and teres major tendons to rotator cuff. After the surgery the children participated in a designed physical therapy program for 6 months. Active shoulder abduction, flexion and external rotation range of motion (ROM) were assessed by electrogoniometer, and functional assessments were measured using the modified Mallet scale. All measurements were taken preoperative, 6 weeks, 3 months, and 6 months postoperatively after the application of the designed PT program. Repeated measure analysis of variance (ANOVA) followed by Bonferroni post-hoc test were used to show the improvement in all measured variables. Analysis revealed that shoulder abduction, flexion and external rotation ROM and shoulder function measured by modified Mallet scale were significantly improved (P<0.0001) after the designed postoperative PT program. It can be concluded that the combination treatment of surgical procedure and the postoperative physical therapy program seem to be effective in improving shoulder and arm functions in children with OBPP. This study describes a detailed physical therapy program after latissimus dorsi and teres major tendons transfer to rotator cuff in OBPP.

pH sensitive quantum dot-anthraquinone nanoconjugates

NASA Astrophysics Data System (ADS)

Ruedas-Rama, Maria Jose; Hall, Elizabeth A. H.

2014-05-01

Semiconductor quantum dots (QDs) have been shown to be highly sensitive to electron or charge transfer processes, which may alter their optical properties. This feature can be exploited for different sensing applications. Here, we demonstrate that QD-anthraquinone conjugates can function as electron transfer-based pH nanosensors. The attachment of the anthraquinones on the surface of QDs results in the reduction of electron hole recombination, and therefore a quenching of the photoluminescence intensity. For some anthraquinone derivatives tested, the quenching mechanism is simply caused by an electron transfer process from QDs to the anthraquinone, functioning as an electron acceptor. For others, electron transfer and energy transfer (FRET) processes were found. A detailed analysis of the quenching processes for CdSe/ZnS QD of two different sizes is presented. The photoluminescence quenching phenomenon of QDs is consistent with the pH sensitive anthraquinone redox chemistry. The resultant family of pH nanosensors shows pKa ranging ˜5-8, being ideal for applications of pH determination in physiological samples like blood or serum, for intracellular pH determination, and for more acidic cellular compartments such as endosomes and lysosomes. The nanosensors showed high selectivity towards many metal cations, including the most physiologically important cations which exist at high concentration in living cells. The reversibility of the proposed systems was also demonstrated. The nanosensors were applied in the determination of pH in samples mimicking the intracellular environment. Finally, the possibility of incorporating a reference QD to achieve quantitative ratiometric measurements was investigated.

Uncertainty Analysis on Heat Transfer Correlations for RP-1 Fuel in Copper Tubing

NASA Technical Reports Server (NTRS)

Driscoll, E. A.; Landrum, D. B.

2004-01-01

NASA is studying kerosene (RP-1) for application in Next Generation Launch Technology (NGLT). Accurate heat transfer correlations in narrow passages at high temperatures and pressures are needed. Hydrocarbon fuels, such as RP-1, produce carbon deposition (coke) along the inside of tube walls when heated to high temperatures. A series of tests to measure the heat transfer using RP-1 fuel and examine the coking were performed in NASA Glenn Research Center's Heated Tube Facility. The facility models regenerative cooling by flowing room temperature RP-1 through resistively heated copper tubing. A Regression analysis is performed on the data to determine the heat transfer correlation for Nusselt number as a function of Reynolds and Prandtl numbers. Each measurement and calculation is analyzed to identify sources of uncertainty, including RP-1 property variations. Monte Carlo simulation is used to determine how each uncertainty source propagates through the regression and an overall uncertainty in predicted heat transfer coefficient. The implications of these uncertainties on engine design and ways to minimize existing uncertainties are discussed.

Integration Of Heat Transfer Coefficient In Glass Forming Modeling With Special Interface Element

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreau, P.; Gregoire, S.; Lochegnies, D.

2007-05-17

Numerical modeling of the glass forming processes requires the accurate knowledge of the heat exchange between the glass and the forming tools. A laboratory testing is developed to determine the evolution of the heat transfer coefficient in different glass/mould contact conditions (contact pressure, temperature, lubrication...). In this paper, trials are performed to determine heat transfer coefficient evolutions in experimental conditions close to the industrial blow-and-blow process conditions. In parallel of this work, a special interface element is implemented in a commercial Finite Element code in order to deal with heat transfer between glass and mould for non-meshing meshes and evolutivemore » contact. This special interface element, implemented by using user subroutines, permits to introduce the previous heat transfer coefficient evolutions in the numerical modelings at the glass/mould interface in function of the local temperatures, contact pressures, contact time and kind of lubrication. The blow-and-blow forming simulation of a perfume bottle is finally performed to assess the special interface element performance.« less

Image Processing, Coding, and Compression with Multiple-Point Impulse Response Functions.

NASA Astrophysics Data System (ADS)

Stossel, Bryan Joseph

1995-01-01

Aspects of image processing, coding, and compression with multiple-point impulse response functions are investigated. Topics considered include characterization of the corresponding random-walk transfer function, image recovery for images degraded by the multiple-point impulse response, and the application of the blur function to image coding and compression. It is found that although the zeros of the real and imaginary parts of the random-walk transfer function occur in continuous, closed contours, the zeros of the transfer function occur at isolated spatial frequencies. Theoretical calculations of the average number of zeros per area are in excellent agreement with experimental results obtained from computer counts of the zeros. The average number of zeros per area is proportional to the standard deviations of the real part of the transfer function as well as the first partial derivatives. Statistical parameters of the transfer function are calculated including the mean, variance, and correlation functions for the real and imaginary parts of the transfer function and their corresponding first partial derivatives. These calculations verify the assumptions required in the derivation of the expression for the average number of zeros. Interesting results are found for the correlations of the real and imaginary parts of the transfer function and their first partial derivatives. The isolated nature of the zeros in the transfer function and its characteristics at high spatial frequencies result in largely reduced reconstruction artifacts and excellent reconstructions are obtained for distributions of impulses consisting of 25 to 150 impulses. The multiple-point impulse response obscures original scenes beyond recognition. This property is important for secure transmission of data on many communication systems. The multiple-point impulse response enables the decoding and restoration of the original scene with very little distortion. Images prefiltered by the random-walk transfer function yield greater compression ratios than are obtained for the original scene. The multiple-point impulse response decreases the bit rate approximately 40-70% and affords near distortion-free reconstructions. Due to the lossy nature of transform-based compression algorithms, noise reduction measures must be incorporated to yield acceptable reconstructions after decompression.

Gravity and Heater Size Effects on Pool Boiling Heat Transfer

NASA Technical Reports Server (NTRS)

Kim, Jungho; Raj, Rishi

2014-01-01

The current work is based on observations of boiling heat transfer over a continuous range of gravity levels between 0g to 1.8g and varying heater sizes with a fluorinert as the test liquid (FC-72/n-perfluorohexane). Variable gravity pool boiling heat transfer measurements over a wide range of gravity levels were made during parabolic flight campaigns as well as onboard the International Space Station. For large heaters and-or higher gravity conditions, buoyancy dominated boiling and heat transfer results were heater size independent. The power law coefficient for gravity in the heat transfer equation was found to be a function of wall temperature under these conditions. Under low gravity conditions and-or for smaller heaters, surface tension forces dominated and heat transfer results were heater size dependent. A pool boiling regime map differentiating buoyancy and surface tension dominated regimes was developed along with a unified framework that allowed for scaling of pool boiling over a wide range of gravity levels and heater sizes. The scaling laws developed in this study are expected to allow performance quantification of phase change based technologies under variable gravity environments eventually leading to their implementation in space based applications.

Acquisition, retention and transfer of simulated laparoscopic tasks using fNIR and a contextual interference paradigm.

PubMed

Shewokis, Patricia A; Shariff, Faiz U; Liu, Yichuan; Ayaz, Hasan; Castellanos, Andres; Lind, D Scott

2017-02-01

Using functional near infrared spectroscopy, a noninvasive, optical brain imaging tool that monitors changes in hemodynamics within the prefrontal cortex (PFC), we assessed performance and cognitive effort during the acquisition, retention and transfer of multiple simulated laparoscopic tasks by novice learners within a contextual interference paradigm. Third-year medical students (n = 10) were randomized to either a blocked or random practice schedule. Across 3 days, students performed 108 acquisition trials of 3 laparoscopic tasks on the LapSim ® simulator followed by delayed retention and transfer tests. Performance metrics (Global score, Total time) and hemodynamic responses (total hemoglobin (μm)) were assessed during skill acquisition, retention and transfer. All acquisition tasks resulted in significant practice schedule X trial block interactions for the left medial anterior PFC. During retention and transfer, random performed the skills in less time and had lower total hemoglobin change in the right dorsolateral PFC than blocked. Compared with blocked, random practice resulted in enhanced learning through better performance and less cognitive load for retention and transfer of simulated laparoscopic tasks. Copyright © 2016 Elsevier Inc. All rights reserved.

Using transfer learning to detect galaxy mergers

NASA Astrophysics Data System (ADS)

Ackermann, Sandro; Schawinksi, Kevin; Zhang, Ce; Weigel, Anna K.; Turp, M. Dennis

2018-05-01

We investigate the use of deep convolutional neural networks (deep CNNs) for automatic visual detection of galaxy mergers. Moreover, we investigate the use of transfer learning in conjunction with CNNs, by retraining networks first trained on pictures of everyday objects. We test the hypothesis that transfer learning is useful for improving classification performance for small training sets. This would make transfer learning useful for finding rare objects in astronomical imaging datasets. We find that these deep learning methods perform significantly better than current state-of-the-art merger detection methods based on nonparametric systems like CAS and GM20. Our method is end-to-end and robust to image noise and distortions; it can be applied directly without image preprocessing. We also find that transfer learning can act as a regulariser in some cases, leading to better overall classification accuracy (p = 0.02). Transfer learning on our full training set leads to a lowered error rate from 0.0381 down to 0.0321, a relative improvement of 15%. Finally, we perform a basic sanity-check by creating a merger sample with our method, and comparing with an already existing, manually created merger catalogue in terms of colour-mass distribution and stellar mass function.

Description, Analysis and Simulation of a New Realization of Digital Filters.

DTIC Science & Technology

1987-09-01

together with its staircase representation h,.(t) . ..... .. ... ... .. 79 6.3 The-RDC LPF transfer function when Td includes 2 zeroes of hc(t) 81 6.4 The...RDC LPF transfer function when Td includes 6 zeroes of hc(t) 82 6.5 The RDC LPF transfer function when Td includes 8 zeroes of h,(t) 83 6.6 The RDC LPF...transfer function when Td includes 6 zeroes of h,(t) and when rectangular and Hamming windows are used ........ ... 84 6.7 The input z(t) and its

a Middle-Ear Reverse Transfer Function Computed from Vibration Measurements of Otoacoustic Emissions on the Ear Drum of the Guinea PIG

NASA Astrophysics Data System (ADS)

Dalhoff, Ernst; Turcanu, Diana; Gummer, Anthony W.

2009-02-01

Using distortion products measured as vibration of the umbo and as sound pressure in the ear canal of guinea pigs, we calculated the corresponding reverse transfer function. We compare the measurements with a middle-ear model taken from the literature and adapted to the guinea pig. A reasonable fit could be achieved. We conclude that the reverse transfer function will be useful to aid fitting a middle-ear model to measured transfer functions of human subjects.

Transfer Function Bounds for Partial-unit-memory Convolutional Codes Based on Reduced State Diagram

NASA Technical Reports Server (NTRS)

Lee, P. J.

1984-01-01

The performance of a coding system consisting of a convolutional encoder and a Viterbi decoder is analytically found by the well-known transfer function bounding technique. For the partial-unit-memory byte-oriented convolutional encoder with m sub 0 binary memory cells and (k sub 0 m sub 0) inputs, a state diagram of 2(K) (sub 0) was for the transfer function bound. A reduced state diagram of (2 (m sub 0) +1) is used for easy evaluation of transfer function bounds for partial-unit-memory codes.

Research of x-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes

NASA Astrophysics Data System (ADS)

Wang, Junfeng; Miao, Changyun; Wang, Wei; Lu, Xiaocui

2008-03-01

An X-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes is researched in the paper. The principle of X-ray nondestructive testing (NDT) is analyzed, the general scheme of the X-ray nondestructive testing system is proposed, and the nondestructive detector for high-speed running conveyor belt with steel wire ropes is developed. The hardware of system is designed with Xilinx's VIRTEX-4 FPGA that embeds PowerPC and MAC IP core, and its network communication software based on TCP/IP protocol is programmed by loading LwIP to PowerPC. The nondestructive testing of high-speed conveyor belt with steel wire ropes and network transfer function are implemented. It is a strong real-time system with rapid scanning speed, high reliability and remotely nondestructive testing function. The nondestructive detector can be applied to the detection of product line in industry.

Determining A Purely Symbolic Transfer Function from Symbol Streams: Theory and Algorithms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, Christopher H

Transfer function modeling is a \\emph{standard technique} in classical Linear Time Invariant and Statistical Process Control. The work of Box and Jenkins was seminal in developing methods for identifying parameters associated with classicalmore » $(r,s,k)$$ transfer functions. Discrete event systems are often \\emph{used} for modeling hybrid control structures and high-level decision problems. \\emph{Examples include} discrete time, discrete strategy repeated games. For these games, a \\emph{discrete transfer function in the form of} an accurate hidden Markov model of input-output relations \\emph{could be used to derive optimal response strategies.} In this paper, we develop an algorithm \\emph{for} creating probabilistic \\textit{Mealy machines} that act as transfer function models for discrete event dynamic systems (DEDS). Our models are defined by three parameters, $$(l_1, l_2, k)$ just as the Box-Jenkins transfer function models. Here $$l_1$$ is the maximal input history lengths to consider, $$l_2$$ is the maximal output history lengths to consider and $k$ is the response lag. Using related results, We show that our Mealy machine transfer functions are optimal in the sense that they maximize the mutual information between the current known state of the DEDS and the next observed input/output pair.« less

Online games training aging brains: limited transfer to cognitive control functions.

PubMed

van Muijden, Jesse; Band, Guido P H; Hommel, Bernhard

2012-01-01

The prevalence of age-related cognitive decline will increase due to graying of the global population. The goal of the present study was to test whether playing online cognitive training games can improve cognitive control (CC) in healthy older adults. Fifty-four older adults (age 60-77) played five different cognitive training games online for 30 min a day over a period of seven weeks (game group). Another group of 20 older adults (age 61-73) instead answered quiz questions about documentaries online (documentary group). Transfer was assessed by means of a cognitive test battery administered before and after the intervention. The test battery included measures of working memory updating, set shifting, response inhibition, attention, and inductive reasoning. Compared with the documentary group, the game group showed larger improvement of inhibition (Stop-Signal task) and inductive reasoning (Raven-SPM), whereas the documentary group showed more improvement in selective attention (UFoV-3). These effects qualify as transfer effects, because response inhibition, inductive reasoning and selective attention were not targeted by the interventions. However, because seven other indicators of CC did not show benefits of game training and some of those that did suffered from potential baseline differences, the study as a whole provides only modest support for the potential of videogame training to improve CC in healthy older adults.

Digital control algorithms for microgravity isolation systems

NASA Technical Reports Server (NTRS)

Sinha, Alok; Wang, Yung-Peng

1992-01-01

New digital control algorithms were developed to achieve the desired acceleration transmissibility function. The attractive electromagnets have been taken as actuators. The relative displacement and the acceleration of the mass were used as feedback signals. Two approaches were developed to find that controller transfer function in Z-domain, which yields the desired transmissibility at each frequency. In the first approach, the controller transfer function is obtained by assuming that the desired transmissibility is known in Z-domain. Since the desired transmissibility H sub d(S) = 1/(tauS+1)(exp 2) is given in S-domain, the first task is to obtain the desired transmissibility in Z-domain. There are three methods to perform this task: bilinear transformation, and backward and forward rectangular rules. The bilinear transformation and backward rectangular rule lead to improper controller transfer functions, which are physically not realizable. The forward rectangular rule does lead to a physically realizable controller. However, this controller is found to be marginally stable because of a pole at Z=1. In order to eliminate this pole, a hybrid control structure is proposed. Here the control input is composed of two parts: analog and digital. The analog input simply represents the velocity (or the integral of acceleration) feedback; and the digital controller which uses only relative displacement signal, is then obtained to achieve the desired closed-loop transfer function. The stability analysis indicates that the controller transfer function is stable for typical values of sampling period. In the second approach, the aforementioned hybrid control structure is again used. First, an analog controller transfer function corresponding to relative displacement feedback is obtained to achieve the transmissibility as 1/(tauS+1)(exp 2). Then the transfer function for the digital control input is obtained by discretizing this analog controller transfer function via bilinear transformation. The stability of the resulting Z-domain closed loop system is analyzed. Also, the frequency response of the Z-domain closed-loop transfer function is determined to evaluate the performance of the control system.

Rehabilitation, Using Guided Cerebral Plasticity, of a Brachial Plexus Injury Treated with Intercostal and Phrenic Nerve Transfers.

PubMed

Dahlin, Lars B; Andersson, Gert; Backman, Clas; Svensson, Hampus; Björkman, Anders

2017-01-01

Recovery after surgical reconstruction of a brachial plexus injury using nerve grafting and nerve transfer procedures is a function of peripheral nerve regeneration and cerebral reorganization. A 15-year-old boy, with traumatic avulsion of nerve roots C5-C7 and a non-rupture of C8-T1, was operated 3 weeks after the injury with nerve transfers: (a) terminal part of the accessory nerve to the suprascapular nerve, (b) the second and third intercostal nerves to the axillary nerve, and (c) the fourth to sixth intercostal nerves to the musculocutaneous nerve. A second operation-free contralateral gracilis muscle transfer directly innervated by the phrenic nerve-was done after 2 years due to insufficient recovery of the biceps muscle function. One year later, electromyography showed activation of the biceps muscle essentially with coughing through the intercostal nerves, and of the transferred gracilis muscle by deep breathing through the phrenic nerve. Voluntary flexion of the elbow elicited clear activity in the biceps/gracilis muscles with decreasing activity in intercostal muscles distal to the transferred intercostal nerves (i.e., corresponding to eighth intercostal), indicating cerebral plasticity, where neural control of elbow flexion is gradually separated from control of breathing. To restore voluntary elbow function after nerve transfers, the rehabilitation of patients operated with intercostal nerve transfers should concentrate on transferring coughing function, while patients with phrenic nerve transfers should focus on transferring deep breathing function.

Toward Construct Validation of a Transfer Climate Instrument. [and] Improving Positive Transfer: A Test of Relapse Prevention Training on Transfer Outcomes.

ERIC Educational Resources Information Center

Holton, Elwood F., III; And Others

1997-01-01

Includes "Toward Construct Validation of a Transfer Climate Instrument" (Holton et al.); "Improving Positive Transfer: A Test of Relapse Prevention Training on Transfer Outcomes" (Burke); "Invited Reaction: Progress or Relapse?" (Newstrom); "Invited Reaction: Theory, Research, and Practice" (Tang);…

Growth factor transgenes interactively regulate articular chondrocytes.

PubMed

Shi, Shuiliang; Mercer, Scott; Eckert, George J; Trippel, Stephen B

2013-04-01

Adult articular chondrocytes lack an effective repair response to correct damage from injury or osteoarthritis. Polypeptide growth factors that stimulate articular chondrocyte proliferation and cartilage matrix synthesis may augment this response. Gene transfer is a promising approach to delivering such factors. Multiple growth factor genes regulate these cell functions, but multiple growth factor gene transfer remains unexplored. We tested the hypothesis that multiple growth factor gene transfer selectively modulates articular chondrocyte proliferation and matrix synthesis. We tested the hypothesis by delivering combinations of the transgenes encoding insulin-like growth factor I (IGF-I), fibroblast growth factor-2 (FGF-2), transforming growth factor beta1 (TGF-β1), bone morphogenetic protein-2 (BMP-2), and bone morphogenetic protien-7 (BMP-7) to articular chondrocytes and measured changes in the production of DNA, glycosaminoglycan, and collagen. The transgenes differentially regulated all these chondrocyte activities. In concert, the transgenes interacted to generate widely divergent responses from the cells. These interactions ranged from inhibitory to synergistic. The transgene pair encoding IGF-I and FGF-2 maximized cell proliferation. The three-transgene group encoding IGF-I, BMP-2, and BMP-7 maximized matrix production and also optimized the balance between cell proliferation and matrix production. These data demonstrate an approach to articular chondrocyte regulation that may be tailored to stimulate specific cell functions, and suggest that certain growth factor gene combinations have potential value for cell-based articular cartilage repair. Copyright © 2012 Wiley Periodicals, Inc.

Development of a new assessment scale for measuring interaction during staff-assisted transfer of residents in dementia special care units.

PubMed

Thunborg, Charlotta; von Heideken Wågert, Petra; Götell, Eva; Ivarsson, Ann-Britt; Söderlund, Anne

2015-02-10

Mobility problems and cognitive deficits related to transferring or moving persons suffering from dementia are associated with dependency. Physical assistance provided by staff is an important component of residents' maintenance of mobility in dementia care facilities. Unfortunately, hands-on assistance during transfers is also a source of confusion in persons with dementia, as well as a source of strain in the caregiver. The bidirectional effect of actions in a dementia care dyad involved in transfer is complicated to evaluate. This study aimed to develop an assessment scale for measuring actions related to transferring persons with dementia by dementia care dyads. This study was performed in four phases and guided by the framework of the biopsychosocial model and the approach presented by Social Cognitive Theory. These frameworks provided a starting point for understanding reciprocal effects in dyadic interaction. The four phases were 1) a literature review identifying existing assessment scales; 2) analyses of video-recorded transfer of persons with dementia for further generation of items, 3) computing the item content validity index of the 93 proposed items by 15 experts; and 4) expert opinion on the response scale and feasibility testing of the new assessment scale by video observation of the transfer situations. The development process resulted in a 17-item scale with a seven-point response scale. The scale consists of two sections. One section is related to transfer-related actions (e.g., capability of communication, motor skills performance, and cognitive functioning) of the person with dementia. The other section addresses the caregivers' facilitative actions (e.g., preparedness of transfer aids, interactional skills, and means of communication and interaction). The literature review and video recordings provided ideas for the item pool. Expert opinion decreased the number of items by relevance ratings and qualitative feedback. No further development of items was performed after feasibility testing of the scale. To enable assessment of transfer-related actions in dementia care dyads, our new scale shows potential for bridging the gap in this area. Results from this study could provide health care professionals working in dementia care facilities with a useful tool for assessing transfer-related actions.

Horizontal gene transfer in an acid mine drainage microbial community.

PubMed

Guo, Jiangtao; Wang, Qi; Wang, Xiaoqi; Wang, Fumeng; Yao, Jinxian; Zhu, Huaiqiu

2015-07-04

Horizontal gene transfer (HGT) has been widely identified in complete prokaryotic genomes. However, the roles of HGT among members of a microbial community and in evolution remain largely unknown. With the emergence of metagenomics, it is nontrivial to investigate such horizontal flow of genetic materials among members in a microbial community from the natural environment. Because of the lack of suitable methods for metagenomics gene transfer detection, microorganisms from a low-complexity community acid mine drainage (AMD) with near-complete genomes were used to detect possible gene transfer events and suggest the biological significance. Using the annotation of coding regions by the current tools, a phylogenetic approach, and an approximately unbiased test, we found that HGTs in AMD organisms are not rare, and we predicted 119 putative transferred genes. Among them, 14 HGT events were determined to be transfer events among the AMD members. Further analysis of the 14 transferred genes revealed that the HGT events affected the functional evolution of archaea or bacteria in AMD, and it probably shaped the community structure, such as the dominance of G-plasma in archaea in AMD through HGT. Our study provides a novel insight into HGT events among microorganisms in natural communities. The interconnectedness between HGT and community evolution is essential to understand microbial community formation and development.

Outcome of Lateral Transfer of the FHL or FDL for Concomitant Peroneal Tendon Tears.

PubMed

Seybold, Jeffrey D; Campbell, John T; Jeng, Clifford L; Short, Kelly W; Myerson, Mark S

2016-06-01

Concomitant tears of the peroneus longus and brevis tendons are rare injuries, with literature limited to case reports and small patient series. Only 1 recent study directly compared the results of single-stage lateral deep flexor transfer, and no previous series objectively evaluated power and balance following transfer. The purpose of this study was to evaluate clinical outcomes, patient satisfaction, and objective power and balance data following single-stage flexor hallucis longus (FHL) and flexor digitorum longus (FDL) tendon transfers for treatment of concomitant peroneus longus and brevis tears. Over an 8-year period (2005-2012), 9 patients underwent lateral transfer of the FHL or FDL tendon for treatment of concomitant peroneus longus and brevis tears. All but 1 patient underwent additional procedures to address hindfoot malalignment or other contributing deformity at the time of surgery. Mean age was 56.9 years, and average body mass index was 27.9. Lateral transfer of the FHL was performed in 5 patients, and FDL transfer performed in 4 with mean follow-up 35.7 months (range: 11-94). Eight of 9 patients completed SF-12 and Foot Function Index (FFI) scores, and 7 returned for range of motion (ROM) and manual strength testing of the involved and normal extremities. These 7 patients also completed force plate balance tests, in addition to peak force and power testing on a PrimusRS machine with a certified physical therapist. All patients were satisfied with the results of the procedure. Mean SF-12 physical and mental scores were 32 and 55, respectively; mean FFI total score was 56.7. No postoperative infections were noted. Two patients continued to utilize orthotics or braces, and 2 patients reported occasional pain with weightbearing activity. Three patients noted mild paresthesias in the distribution of the sural nerve and 2 demonstrated tibial neuritis. All patients demonstrated 4/5 eversion strength in the involved extremity. Average loss of inversion and eversion ROM were 24.7% and 27.2% of normal, respectively. Mean postoperative eversion peak force and power were decreased greater than 55% relative to the normal extremity. Patients demonstrated nearly 50% increases in both center-of-pressure tracing length and velocity during balance testing. There were no statistically significant differences between the FHL and FDL transfer groups with regards to clinical examination or objective power and balance tests. The FHL and FDL tendons were both successful options for lateral transfer in cases of concomitant peroneus longus and brevis tears. Objective measurements of strength and balance demonstrated significant deficits in the operative extremity, even years following the procedure. These differences, however, did not appear to alter or inhibit patient activity levels or high satisfaction rates with the procedure. Although anatomic studies have demonstrated benefits of FHL transfer over the FDL tendon, further studies with increased patient numbers are needed to determine if these differences are clinically significant. Level IV, retrospective case series. © The Author(s) 2016.

The role of external and internal mass transfer in the process of Cu2+ removal by natural mineral sorbents.

PubMed

Sljivić, M; Smiciklas, I; Plećas, I; Pejanović, S

2011-07-01

The kinetics of Cu2+ sorption on to zeolite, clay and diatomite was investigated as a function of initial metal concentrations. For consideration of the mass transfer phenomena, single resistance models based on both film and intraparticle diffusion were tested and compared. The obtained results suggested that the rate-limiting step in Cu2+ sorption strongly depended on the sorbent type, as well as on initial cation concentration. The decrease in external mass transfer coefficients with the increase in initial metal concentrations was in excellent agreement with expressions based on Sherwood and Schmidt dimensionless numbers. The internal diffusivities through zeolite particles were in the range 1.0 x 10(-11) to 1.0 x 10(-13) m2/min, depending on the Cu2+ concentration and the applied theoretical model.

BIOCHEM-ORCHESTRA: a tool for evaluating chemical speciation and ecotoxicological impacts of heavy metals on river flood plain systems.

PubMed

Vink, J P M; Meeussen, J C L

2007-08-01

The chemical speciation model BIOCHEM was extended with ecotoxicological transfer functions for uptake of metals (As, Cd, Cu, Ni, Pb, and Zn) by plants and soil invertebrates. It was coupled to the object-oriented framework ORCHESTRA to achieve a flexible and dynamic decision support system (DSS) to analyse natural or anthropogenic changes that occur in river systems. The DSS uses the chemical characteristics of soils and sediments as input, and calculates speciation and subsequent uptake by biota at various scenarios. Biotic transfer functions were field-validated, and actual hydrological conditions were derived from long-term monitoring data. The DSS was tested for several scenarios that occur in the Meuse catchment areas, such as flooding and sedimentation of riverine sediments on flood plains. Risks are expressed in terms of changes in chemical mobility, and uptake by flood plain key species (flora and fauna).

Multi-step optimization strategy for fuel-optimal orbital transfer of low-thrust spacecraft

NASA Astrophysics Data System (ADS)

Rasotto, M.; Armellin, R.; Di Lizia, P.

2016-03-01

An effective method for the design of fuel-optimal transfers in two- and three-body dynamics is presented. The optimal control problem is formulated using calculus of variation and primer vector theory. This leads to a multi-point boundary value problem (MPBVP), characterized by complex inner constraints and a discontinuous thrust profile. The first issue is addressed by embedding the MPBVP in a parametric optimization problem, thus allowing a simplification of the set of transversality constraints. The second problem is solved by representing the discontinuous control function by a smooth function depending on a continuation parameter. The resulting trajectory optimization method can deal with different intermediate conditions, and no a priori knowledge of the control structure is required. Test cases in both the two- and three-body dynamics show the capability of the method in solving complex trajectory design problems.

Optimizing an Actuator Array for the Control of Multi-Frequency Noise in Aircraft Interiors

NASA Technical Reports Server (NTRS)

Palumbo, D. L.; Padula, S. L.

1997-01-01

Techniques developed for selecting an optimized actuator array for interior noise reduction at a single frequency are extended to the multi-frequency case. Transfer functions for 64 actuators were obtained at 5 frequencies from ground testing the rear section of a fully trimmed DC-9 fuselage. A single loudspeaker facing the left side of the aircraft was the primary source. A combinatorial search procedure (tabu search) was employed to find optimum actuator subsets of from 2 to 16 actuators. Noise reduction predictions derived from the transfer functions were used as a basis for evaluating actuator subsets during optimization. Results indicate that it is necessary to constrain actuator forces during optimization. Unconstrained optimizations selected actuators which require unrealistically large forces. Two methods of constraint are evaluated. It is shown that a fast, but approximate, method yields results equivalent to an accurate, but computationally expensive, method.

Enhancements to the SSME transfer function modeling code

NASA Technical Reports Server (NTRS)

Irwin, R. Dennis; Mitchell, Jerrel R.; Bartholomew, David L.; Glenn, Russell D.

1995-01-01

This report details the results of a one year effort by Ohio University to apply the transfer function modeling and analysis tools developed under NASA Grant NAG8-167 (Irwin, 1992), (Bartholomew, 1992) to attempt the generation of Space Shuttle Main Engine High Pressure Turbopump transfer functions from time domain data. In addition, new enhancements to the transfer function modeling codes which enhance the code functionality are presented, along with some ideas for improved modeling methods and future work. Section 2 contains a review of the analytical background used to generate transfer functions with the SSME transfer function modeling software. Section 2.1 presents the 'ratio method' developed for obtaining models of systems that are subject to single unmeasured excitation sources and have two or more measured output signals. Since most of the models developed during the investigation use the Eigensystem Realization Algorithm (ERA) for model generation, Section 2.2 presents an introduction of ERA, and Section 2.3 describes how it can be used to model spectral quantities. Section 2.4 details the Residue Identification Algorithm (RID) including the use of Constrained Least Squares (CLS) and Total Least Squares (TLS). Most of this information can be found in the report (and is repeated for convenience). Section 3 chronicles the effort of applying the SSME transfer function modeling codes to the a51p394.dat and a51p1294.dat time data files to generate transfer functions from the unmeasured input to the 129.4 degree sensor output. Included are transfer function modeling attempts using five methods. The first method is a direct application of the SSME codes to the data files and the second method uses the underlying trends in the spectral density estimates to form transfer function models with less clustering of poles and zeros than the models obtained by the direct method. In the third approach, the time data is low pass filtered prior to the modeling process in an effort to filter out high frequency characteristics. The fourth method removes the presumed system excitation and its harmonics in order to investigate the effects of the excitation on the modeling process. The fifth method is an attempt to apply constrained RID to obtain better transfer functions through more accurate modeling over certain frequency ranges. Section 4 presents some new C main files which were created to round out the functionality of the existing SSME transfer function modeling code. It is now possible to go from time data to transfer function models using only the C codes; it is not necessary to rely on external software. The new C main files and instructions for their use are included. Section 5 presents current and future enhancements to the XPLOT graphics program which was delivered with the initial software. Several new features which have been added to the program are detailed in the first part of this section. The remainder of Section 5 then lists some possible features which may be added in the future. Section 6 contains the conclusion section of this report. Section 6.1 is an overview of the work including a summary and observations relating to finding transfer functions with the SSME code. Section 6.2 contains information relating to future work on the project.

Modeling collision energy transfer in APCI/CID mass spectra of PAHs using thermal-like post-collision internal energy distributions

NASA Astrophysics Data System (ADS)

Solano, Eduardo A.; Mohamed, Sabria; Mayer, Paul M.

2016-10-01

The internal energy transferred when projectile molecular ions of naphthalene collide with argon gas atoms was extracted from the APCI-CID (atmospheric-pressure chemical ionization collision-induced dissociation) mass spectra acquired as a function of collision energy. Ion abundances were calculated by microcanonical integration of the differential rate equations using the Rice-Ramsperger-Kassel-Marcus rate constants derived from a UB3LYP/6-311G+(3df,2p)//UB3LYP/6-31G(d) fragmentation mechanism and thermal-like vibrational energy distributions p M (" separators=" E , T char ) . The mean vibrational energy excess of the ions was characterized by the parameter Tchar ("characteristic temperature"), determined by fitting the theoretical ion abundances to the experimental breakdown graph (a plot of relative abundances of the ions as a function of kinetic energy) of activated naphthalene ions. According to these results, the APCI ion source produces species below Tchar = 1457 K, corresponding to 3.26 eV above the vibrational ground state. Subsequent collisions heat the ions up further, giving rise to a sigmoid curve of Tchar as a function of Ecom (center-of-mass-frame kinetic energy). The differential internal energy absorption per kinetic energy unit (dEvib/dEcom) changes with Ecom according to a symmetric bell-shaped function with a maximum at 6.38 ± 0.32 eV (corresponding to 6.51 ± 0.27 eV of vibrational energy excess), and a half-height full width of 6.30 ± 1.15 eV. This function imposes restrictions on the amount of energy that can be transferred by collisions, such that a maximum is reached as kinetic energy is increased. This behavior suggests that the collisional energy transfer exhibits a pronounced increase around some specific value of energy. Finally, the model is tested against the CID mass spectra of anthracene and pyrene ions and the corresponding results are discussed.

Modeling collision energy transfer in APCI/CID mass spectra of PAHs using thermal-like post-collision internal energy distributions.

PubMed

Solano, Eduardo A; Mohamed, Sabria; Mayer, Paul M

2016-10-28

The internal energy transferred when projectile molecular ions of naphthalene collide with argon gas atoms was extracted from the APCI-CID (atmospheric-pressure chemical ionization collision-induced dissociation) mass spectra acquired as a function of collision energy. Ion abundances were calculated by microcanonical integration of the differential rate equations using the Rice-Ramsperger-Kassel-Marcus rate constants derived from a UB3LYP/6-311G+(3df,2p)//UB3LYP/6-31G(d) fragmentation mechanism and thermal-like vibrational energy distributions p M E,T char . The mean vibrational energy excess of the ions was characterized by the parameter T char ("characteristic temperature"), determined by fitting the theoretical ion abundances to the experimental breakdown graph (a plot of relative abundances of the ions as a function of kinetic energy) of activated naphthalene ions. According to these results, the APCI ion source produces species below T char = 1457 K, corresponding to 3.26 eV above the vibrational ground state. Subsequent collisions heat the ions up further, giving rise to a sigmoid curve of T char as a function of E com (center-of-mass-frame kinetic energy). The differential internal energy absorption per kinetic energy unit (dE vib /dE com ) changes with E com according to a symmetric bell-shaped function with a maximum at 6.38 ± 0.32 eV (corresponding to 6.51 ± 0.27 eV of vibrational energy excess), and a half-height full width of 6.30 ± 1.15 eV. This function imposes restrictions on the amount of energy that can be transferred by collisions, such that a maximum is reached as kinetic energy is increased. This behavior suggests that the collisional energy transfer exhibits a pronounced increase around some specific value of energy. Finally, the model is tested against the CID mass spectra of anthracene and pyrene ions and the corresponding results are discussed.

Macrophage function in murine allogeneic bone marrow radiation chimeras in the early phase after transplantation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roesler, J.; Baccarini, M.; Vogt, B.

1989-08-01

We tested several of the functions of macrophages (M phi) in the early phase after allogeneic bone marrow transfer to get information about this important aspect of the nonspecific immune system in the T-cell-deficient recipient. On days 3-5 after transfer, the number of M phi was reduced in the spleen, liver, lungs, and peritoneal cavity (Pe). The phagocytosis of sheep red blood cells (SRBC) by these M phi was normal or even enhanced, as in the case of Pe-M phi. Already on days 8-12 after transfer, the number of M phi in spleen and liver exceeded that of controls, whereasmore » the number was still reduced in lungs and Pe. We examined their ability to kill P815 tumor cells, to produce tumor necrosis factor-alpha (TNF alpha), to phagocytose SRBC, to produce reactive oxygen intermediates (ROI) in vitro and to kill Listeria monocytogenes in vivo. Most functions were normal and often even enhanced, depending on the organ origin, but the ability of Pe-M phi to produce ROI was reduced. Proliferative response to macrophage colony-stimulating factor (M-CSF) and killing of YAC-1 tumor cells revealed a high frequency of macrophage precursor cells in the spleen and liver and a high natural killer (NK) activity in the liver. Altogether, enhanced nonspecific immune function, especially preactivated M phi, may enable chimeras to survive attacks by opportunistic pathogens.« less

Crystalline lens MTF measurement during simulated accommodation

NASA Astrophysics Data System (ADS)

Borja, David; Takeuchi, Gaku; Ziebarth, Noel; Acosta, Ana C.; Manns, Fabrice; Parel, Jean-Marie

2005-04-01

Purpose: To design and test an optical system to measure the optical quality of post mortem lenses during simulated accommodation. Methods: An optical bench top system was designed to measure the point spread function and calculate the modulation transfer function (MTF) of monkey and human ex-vivo crystalline lenses. The system consists of a super luminescent diode emitting at 850nm, collimated into a 3mm beam which is focused by the ex-vivo lens under test. The intensity distribution at the focus (point spread function) is re-imaged and magnified onto a beam profiler CCD camera. The optical quality in terms of spatial frequency response (modulation transfer function) is calculated by Fourier transform of the point spread function. The system was used on ex-vivo lenses with attached zonules, ciliary body and sclera. The sclera was glued to 8 separate PMMA segments and stretched radial by 5mm on an accommodation simulating lens stretching device. The point spread function was measured for each lens in the relaxed and stretched state for 5 human (ages 38-86 years) and 5 cynomolgus monkey (ages 53 - 67 months) fresh post mortem crystalline lenses. Results: Stretching induced measurable changes in the MTF. The cutoff frequency increased from 54.4+/-13.6 lp/mm unstretched to 59.5+/-21.4 lp/mm stretched in the post-presbyopic human and from 51.9+/-24.7 lp/mm unstretched to 57.7+/-18.5 lp/mm stretched cynomolgus monkey lenses. Conclusion: The results demonstrate the feasibility of measuring the optical quality of ex-vivo human and cynomolgus monkey lenses during simulated accommodation. Additional experiments are underway to quantify changes in optical quality induced by stretching.

SAR Processing Based On Two-Dimensional Transfer Function

NASA Technical Reports Server (NTRS)

Chang, Chi-Yung; Jin, Michael Y.; Curlander, John C.

1994-01-01

Exact transfer function, ETF, is two-dimensional transfer function that constitutes basis of improved frequency-domain-convolution algorithm for processing synthetic-aperture-radar, SAR data. ETF incorporates terms that account for Doppler effect of motion of radar relative to scanned ground area and for antenna squint angle. Algorithm based on ETF outperforms others.

Effects of a recreational ice skating program on the functional mobility of a child with cerebral palsy.

PubMed

Walsh, Sharon Fleming; Scharf, Michael G

2014-04-01

The purpose of this study was to describe the effects of an ice skating program on the ambulation, strength, posture and balance of a child with cerebral palsy (CP). The subject was a five-year-old female with a diagnosis of CP and a Gross Motor Classification System level of III. The subject was a slow and labored household ambulator on level surfaces with bilateral forearm crutches and bilateral ankle foot orthoses. She was unable to transfer to and from the floor to stand independently, stand unsupported or take steps independently. Until the initiation of this study she was receiving physical therapy services 2×/week. For the purpose of this study she participated in a 1 h/week local ice skating program for people with disabilities for a period of four months. The subject displayed clinically significant improvements in functional mobility including: improved standing posture; independent transfer to and from the floor to stand; maintenance of independent standing for 3 min; independent walking for 10 feet; increased ability to isolate extremity musculature; increased strength; improved Gross Motor Function Measure-88 scores and increased endurance. A subsequent testing session four months after the ice skating program had ended displayed declines but not to pre-intervention levels in muscle strength; ability to transfer to and from the floor to stand; functional mobility and standing balance. The results appear to suggest that the participation in an ice skating program clinically improved this child's functional mobility. Further research needs to be done with regard to physical recreational programs and the benefit they can have on the function of children with activity limitations.

Prediction of the vibroacoustic behavior of a submerged shell with non-axisymmetric internal substructures by a condensed transfer function method

NASA Astrophysics Data System (ADS)

Meyer, V.; Maxit, L.; Guyader, J.-L.; Leissing, T.

2016-01-01

The vibroacoustic behavior of axisymmetric stiffened shells immersed in water has been intensively studied in the past. On the contrary, little attention has been paid to the modeling of these shells coupled to non-axisymmetric internal frames. Indeed, breaking the axisymmetry couples the circumferential orders of the Fourier series and considerably increases the computational costs. In order to tackle this issue, we propose a sub-structuring approach called the Condensed Transfer Function (CTF) method that will allow assembling a model of axisymmetric stiffened shell with models of non-axisymmetric internal frames. The CTF method is developed in the general case of mechanical subsystems coupled along curves. A set of orthonormal functions called condensation functions, which depend on the curvilinear abscissa along the coupling line, is considered. This set is then used as a basis for approximating and decomposing the displacements and the applied forces at the line junctions. Thanks to the definition and calculation of condensed transfer functions for each uncoupled subsystem and by using the superposition principle for passive linear systems, the behavior of the coupled subsystems can be deduced. A plane plate is considered as a test case to study the convergence of the method with respect to the type and the number of condensation functions taken into account. The CTF method is then applied to couple a submerged non-periodically stiffened shell described using the Circumferential Admittance Approach (CAA) with internal substructures described by Finite Element Method (FEM). The influence of non-axisymmetric internal substructures can finally be studied and it is shown that it tends to increase the radiation efficiency of the shell and can modify the vibrational and acoustic energy distribution.

Reverse shoulder arthroplasty for massive rotator cuff tear: risk factors for poor functional improvement.

PubMed

Hartzler, Robert U; Steen, Brandon M; Hussey, Michael M; Cusick, Michael C; Cottrell, Benjamin J; Clark, Rachel E; Frankle, Mark A

2015-11-01

Some patients unexpectedly have poor functional improvement after reverse shoulder arthroplasty (RSA) for massive rotator cuff tear without glenohumeral arthritis. Our aim was to identify risk factors for this outcome. We also assessed the value of RSA for cases with poor functional improvement vs. The study was a retrospective case-control analysis for primary RSA performed for massive rotator cuff tear without glenohumeral arthritis with minimum 2-year follow-up. Cases were defined as Simple Shoulder Test (SST) score improvement of ≤1, whereas controls improved SST score ≥2. Risk factors were chosen on the basis of previous association with poor outcomes after shoulder arthroplasty. Latissimus dorsi tendon transfer results were analyzed as a subgroup. Value was defined as improvement in American Shoulder and Elbow Surgeons (ASES) score per $10,000 hospital cost. In a multivariate binomial logistic regression analysis, neurologic dysfunction (P = .006), age <60 years (P = .02), and high preoperative SST score (P = .03) were independently associated with poor functional improvement. Latissimus dorsi tendon transfer patients significantly improved in active external rotation (-0.3° to 38.7°; P < .01). The value of RSA (ΔASES/$10,000 cost) for cases was 0.8 compared with 17.5 for controls (P < .0001). Young age, high preoperative function, and neurologic dysfunction were associated with poor functional improvement. Surgeons should consider these associations in counseling and selection of patients. Concurrent latissimus dorsi transfer was successful in restoring active external rotation in a subgroup of patients. The critical economic importance of improved patient selection is emphasized by the very low value of the procedure in the case group. Copyright © 2015 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Accelerated Recovery of Consciousness after General Anesthesia Is Associated with Increased Functional Brain Connectivity in the High-Gamma Bandwidth.

PubMed

Li, Duan; Hambrecht-Wiedbusch, Viviane S; Mashour, George A

2017-01-01

Recent data from our laboratory demonstrate that high-frequency gamma connectivity across the cortex is present during consciousness and depressed during unconsciousness. However, these data were derived from static and well-defined states of arousal rather than during transitions that would suggest functional relevance. We also recently found that subanesthetic ketamine administered during isoflurane anesthesia accelerates recovery upon discontinuation of the primary anesthetic and increases gamma power during emergence. In the current study we re-analyzed electroencephalogram (EEG) data to test the hypothesis that functional cortical connectivity between anterior and posterior cortical regions would be increased during accelerated recovery induced by ketamine when compared to saline-treated controls. Rodents were instrumented with intracranial EEG electrodes and general anesthesia was induced with isoflurane anesthesia. After 37.5 min of continuous isoflurane anesthesia, a subanesthetic dose of ketamine (25 mg/kg intraperitoneal) was administered, with evidence of a 44% reduction in emergence time. In this study, we analyzed gamma and theta coherence (measure of undirected functional connectivity) and normalized symbolic transfer entropy (measure of directed functional connectivity) between frontal and parietal cortices during various levels of consciousness, with a focus on emergence from isoflurane anesthesia. During accelerated emergence in the ketamine-treated group, there was increased frontal-parietal coherence { p = 0.005, 0.05-0.23 [95% confidence interval (CI)]} and normalized symbolic transfer entropy [frontal to parietal: p < 0.001, 0.010-0.026 (95% CI); parietal to frontal: p < 0.001, 0.009-0.025 (95% CI)] in high-frequency gamma bandwidth as compared with the saline-treated group. Surrogates of cortical information exchange in high-frequency gamma are increased in association with accelerated recovery from anesthesia. This finding adds evidence suggesting a functional significance of high-gamma information transfer in consciousness.

Propagation of eigenmodes and transfer functions in waveguide WDM structures

NASA Astrophysics Data System (ADS)

Mashkov, Vladimir A.; Francoeur, S.; Geuss, U.; Neiser, K.; Temkin, Henryk

1998-02-01

A method of propagation functions and transfer amplitudes suitable for the design of integrated optical circuits is presented. The method is based on vectorial formulation of electrodynamics: the distributions and propagation of electromagnetic fields in optical circuits is described by equivalent surface sources. This approach permits a division of complex optical waveguide structures into sets of primitive blocks and to separately calculate the transfer function and the transfer amplitude for each block. The transfer amplitude of the entire optical system is represented by a convolution of transfer amplitudes of its primitive blocks. The eigenvalues and eigenfunctions of arbitrary waveguide structure are obtained in the WKB approximation and compared with other methods. The general approach is illustrated with the transfer amplitude calculations for Dragone's star coupler and router.

FILM-30: A Heat Transfer Properties Code for Water Coolant

DOE Office of Scientific and Technical Information (OSTI.GOV)

MARSHALL, THERON D.

2001-02-01

A FORTRAN computer code has been written to calculate the heat transfer properties at the wetted perimeter of a coolant channel when provided the bulk water conditions. This computer code is titled FILM-30 and the code calculates its heat transfer properties by using the following correlations: (1) Sieder-Tate: forced convection, (2) Bergles-Rohsenow: onset to nucleate boiling, (3) Bergles-Rohsenow: partially developed nucleate boiling, (4) Araki: fully developed nucleate boiling, (5) Tong-75: critical heat flux (CHF), and (6) Marshall-98: transition boiling. FILM-30 produces output files that provide the heat flux and heat transfer coefficient at the wetted perimeter as a function ofmore » temperature. To validate FILM-30, the calculated heat transfer properties were used in finite element analyses to predict internal temperatures for a water-cooled copper mockup under one-sided heating from a rastered electron beam. These predicted temperatures were compared with the measured temperatures from the author's 1994 and 1998 heat transfer experiments. There was excellent agreement between the predicted and experimentally measured temperatures, which confirmed the accuracy of FILM-30 within the experimental range of the tests. FILM-30 can accurately predict the CHF and transition boiling regimes, which is an important advantage over current heat transfer codes. Consequently, FILM-30 is ideal for predicting heat transfer properties for applications that feature high heat fluxes produced by one-sided heating.« less

Carotenoid-to-bacteriochlorophyll energy transfer through vibronic coupling in LH2 from Phaeosprillum molischianum.

PubMed

Thyrhaug, Erling; Lincoln, Craig N; Branchi, Federico; Cerullo, Giulio; Perlík, Václav; Šanda, František; Lokstein, Heiko; Hauer, Jürgen

2018-03-01

The peripheral light-harvesting antenna complex (LH2) of purple photosynthetic bacteria is an ideal testing ground for models of structure-function relationships due to its well-determined molecular structure and ultrafast energy deactivation. It has been the target for numerous studies in both theory and ultrafast spectroscopy; nevertheless, certain aspects of the convoluted relaxation network of LH2 lack a satisfactory explanation by conventional theories. For example, the initial carotenoid-to-bacteriochlorophyll energy transfer step necessary on visible light excitation was long considered to follow the Förster mechanism, even though transfer times as short as 40 femtoseconds (fs) have been observed. Such transfer times are hard to accommodate by Förster theory, as the moderate coupling strengths found in LH2 suggest much slower transfer within this framework. In this study, we investigate LH2 from Phaeospirillum (Ph.) molischianum in two types of transient absorption experiments-with narrowband pump and white-light probe resulting in 100 fs time resolution, and with degenerate broadband 10 fs pump and probe pulses. With regard to the split Q x band in this system, we show that vibronically mediated transfer explains both the ultrafast carotenoid-to-B850 transfer, and the almost complete lack of transfer to B800. These results are beyond Förster theory, which predicts an almost equal partition between the two channels.

Determination of the mass transfer limiting step of dye adsorption onto commercial adsorbent by using mathematical models.

PubMed

Marin, Pricila; Borba, Carlos Eduardo; Módenes, Aparecido Nivaldo; Espinoza-Quiñones, Fernando R; de Oliveira, Silvia Priscila Dias; Kroumov, Alexander Dimitrov

2014-01-01

Reactive blue 5G dye removal in a fixed-bed column packed with Dowex Optipore SD-2 adsorbent was modelled. Three mathematical models were tested in order to determine the limiting step of the mass transfer of the dye adsorption process onto the adsorbent. The mass transfer resistance was considered to be a criterion for the determination of the difference between models. The models contained information about the external, internal, or surface adsorption limiting step. In the model development procedure, two hypotheses were applied to describe the internal mass transfer resistance. First, the mass transfer coefficient constant was considered. Second, the mass transfer coefficient was considered as a function of the dye concentration in the adsorbent. The experimental breakthrough curves were obtained for different particle diameters of the adsorbent, flow rates, and feed dye concentrations in order to evaluate the predictive power of the models. The values of the mass transfer parameters of the mathematical models were estimated by using the downhill simplex optimization method. The results showed that the model that considered internal resistance with a variable mass transfer coefficient was more flexible than the other ones and this model described the dynamics of the adsorption process of the dye in the fixed-bed column better. Hence, this model can be used for optimization and column design purposes for the investigated systems and similar ones.

Introduction to Flight Test Engineering (Introduction aux techniques des essais en vol)

DTIC Science & Technology

2005-07-01

or aircraft parameters • Calculations in the frequency domain ( Fast Fourier Transform) • Data analysis with dedicated software for: • Signal...density Fast Fourier Transform Transfer function analysis Frequency response analysis Etc. PRESENTATION Color/black & white Display screen...envelope by operating the airplane at increasing ranges - representing increasing risk - of engine operation, airspeeds both fast and slow, altitude

Naming and Categorization in Young Children: IV: Listener Behavior Training and Transfer of Function

ERIC Educational Resources Information Center

Horne, Pauline J.; Hughes, J. Carl; Lowe, C. Fergus

2006-01-01

Following pretraining with everyday objects, 14 children aged from 1 to 4 years were trained, for each of three pairs of different arbitrary wooden shapes (Set 1), to select one stimulus in response to the spoken word /zog/, and the other to /vek/. When given a test for the corresponding tacts ("zog" and "vek"), 10 children…

Designing and testing a wearable, wireless fNIRS patch.

PubMed

Abtahi, Mohammadreza; Cay, Gozde; Saikia, Manob Jyoti; Mankodiya, Kunal

2016-08-01

Optical brain monitoring using near infrared (NIR) light has got a lot of attention in order to study the complexity of the brain due to several advantages as oppose to other methods such as EEG, fMRI and PET. There are a few commercially available functional NIR spectroscopy (fNIRS) brain monitoring systems, but they are still non-wearable and pose difficulties in scanning the brain while the participants are in motion. In this work, we present our endeavors to design and test a low-cost, wireless fNIRS patch using NIR light sources at wavelengths of 770 and 830nm, photodetectors and a microcontroller to trigger the light sources, read photodetector's output and transfer data wirelessly (via Bluetooth) to a smart-phone. The patch is essentially a 3-D printed wearable system, recording and displaying the brain hemodynamic responses on smartphone, also eliminates the need for complicated wiring of the electrodes. We have performed rigorous lab experiments on the presented system for its functionality. In a proof of concept experiment, the patch detected the NIR absorption on the arm. Another experiment revealed that the patch's battery could last up to several hours with continuous fNIRS recording with and without wireless data transfer.

Optical testbed for the LISA phasemeter

NASA Astrophysics Data System (ADS)

Schwarze, T. S.; Fernández Barranco, G.; Penkert, D.; Gerberding, O.; Heinzel, G.; Danzmann, K.

2016-05-01

The planned spaceborne gravitational wave detector LISA will allow the detection of gravitational waves at frequencies between 0.1 mHz and 1 Hz. A breadboard model for the metrology system aka the phasemeter was developed in the scope of an ESA technology development project by a collaboration between the Albert Einstein Institute, the Technical University of Denmark and the Danish industry partner Axcon Aps. It in particular provides the electronic readout of the main interferometer phases besides auxiliary functions. These include clock noise transfer, ADC pilot tone correction, inter-satellite ranging and data transfer. Besides in LISA, the phasemeter can also be applied in future satellite geodesy missions. Here we show the planning and advances in the implementation of an optical testbed for the full metrology chain. It is based on an ultra-stable hexagonal optical bench. This bench allows the generation of three unequal heterodyne beatnotes with a zero phase combination, thus providing the possibility to probe the phase readout for non-linearities in an optical three signal test. Additionally, the utilization of three independent phasemeters will allow the testing of the auxiliary functions. Once working, components can individually be replaced with flight-qualified hardware in this setup.

Spatially Controlled Noncovalent Functionalization of 2D Materials Based on Molecular Architecture.

PubMed

Bang, Jae Jin; Porter, Ashlin G; Davis, Tyson C; Hayes, Tyler R; Claridge, Shelley A

2018-05-15

Polymerizable amphiphiles can be assembled into lying-down phases on 2D materials such as graphite and graphene to create chemically orthogonal surface patterns at 5-10 nm scales, locally modulating functionality of the 2D basal plane. Functionalization can be carried out through Langmuir-Schaefer conversion, in which a subset of molecules is transferred out of a standing phase film on water onto the 2D substrate. Here, we leverage differences in molecular structure to spatially control transfer at both nanoscopic and microscopic scales. We compare transfer properties of five different single- and dual-chain amphiphiles, demonstrating that those with strong lateral interactions (e.g., hydrogen-bonding networks) exhibit the lowest transfer efficiencies. Since molecular structures also influence microscopic domain morphologies in Langmuir films, we show that it is possible to transfer such microscale patterns, taking advantage of variations in the local transfer rates based on the structural heterogeneity in Langmuir films. Nanoscale domain morphologies also vary in ways that are consistent with predicted relative transfer and diffusion rates. These results suggest strategies to tailor noncovalent functionalization of 2D substrates through controlled LS transfer.

The influence of a wall function on turbine blade heat transfer prediction

NASA Technical Reports Server (NTRS)

Whitaker, Kevin W.

1989-01-01

The second phase of a continuing investigation to improve the prediction of turbine blade heat transfer coefficients was completed. The present study specifically investigated how a numeric wall function in the turbulence model of a two-dimensional boundary layer code, STAN5, affected heat transfer prediction capabilities. Several sources of inaccuracy in the wall function were identified and then corrected or improved. Heat transfer coefficient predictions were then obtained using each one of the modifications to determine its effect. Results indicated that the modifications made to the wall function can significantly affect the prediction of heat transfer coefficients on turbine blades. The improvement in accuracy due the modifications is still inconclusive and is still being investigated.

Performance of Frozen Density Embedding for Modeling Hole Transfer Reactions.

PubMed

Ramos, Pablo; Papadakis, Markos; Pavanello, Michele

2015-06-18

We have carried out a thorough benchmark of the frozen density-embedding (FDE) method for calculating hole transfer couplings. We have considered 10 exchange-correlation functionals, 3 nonadditive kinetic energy functionals, and 3 basis sets. Overall, we conclude that with a 7% mean relative unsigned error, the PBE and PW91 functionals coupled with the PW91k nonadditive kinetic energy functional and a TZP basis set constitute the most stable and accurate levels of theory for hole transfer coupling calculations. The FDE-ET method is found to be an excellent tool for computing diabatic couplings for hole transfer reactions.

AU-FREDI - AUTONOMOUS FREQUENCY DOMAIN IDENTIFICATION

NASA Technical Reports Server (NTRS)

Yam, Y.

1994-01-01

The Autonomous Frequency Domain Identification program, AU-FREDI, is a system of methods, algorithms and software that was developed for the identification of structural dynamic parameters and system transfer function characterization for control of large space platforms and flexible spacecraft. It was validated in the CALTECH/Jet Propulsion Laboratory's Large Spacecraft Control Laboratory. Due to the unique characteristics of this laboratory environment, and the environment-specific nature of many of the software's routines, AU-FREDI should be considered to be a collection of routines which can be modified and reassembled to suit system identification and control experiments on large flexible structures. The AU-FREDI software was originally designed to command plant excitation and handle subsequent input/output data transfer, and to conduct system identification based on the I/O data. Key features of the AU-FREDI methodology are as follows: 1. AU-FREDI has on-line digital filter design to support on-orbit optimal input design and data composition. 2. Data composition of experimental data in overlapping frequency bands overcomes finite actuator power constraints. 3. Recursive least squares sine-dwell estimation accurately handles digitized sinusoids and low frequency modes. 4. The system also includes automated estimation of model order using a product moment matrix. 5. A sample-data transfer function parametrization supports digital control design. 6. Minimum variance estimation is assured with a curve fitting algorithm with iterative reweighting. 7. Robust root solvers accurately factorize high order polynomials to determine frequency and damping estimates. 8. Output error characterization of model additive uncertainty supports robustness analysis. The research objectives associated with AU-FREDI were particularly useful in focusing the identification methodology for realistic on-orbit testing conditions. Rather than estimating the entire structure, as is typically done in ground structural testing, AU-FREDI identifies only the key transfer function parameters and uncertainty bounds that are necessary for on-line design and tuning of robust controllers. AU-FREDI's system identification algorithms are independent of the JPL-LSCL environment, and can easily be extracted and modified for use with input/output data files. The basic approach of AU-FREDI's system identification algorithms is to non-parametrically identify the sampled data in the frequency domain using either stochastic or sine-dwell input, and then to obtain a parametric model of the transfer function by curve-fitting techniques. A cross-spectral analysis of the output error is used to determine the additive uncertainty in the estimated transfer function. The nominal transfer function estimate and the estimate of the associated additive uncertainty can be used for robust control analysis and design. AU-FREDI's I/O data transfer routines are tailored to the environment of the CALTECH/ JPL-LSCL which included a special operating system to interface with the testbed. Input commands for a particular experiment (wideband, narrowband, or sine-dwell) were computed on-line and then issued to respective actuators by the operating system. The operating system also took measurements through displacement sensors and passed them back to the software for storage and off-line processing. In order to make use of AU-FREDI's I/O data transfer routines, a user would need to provide an operating system capable of overseeing such functions between the software and the experimental setup at hand. The program documentation contains information designed to support users in either providing such an operating system or modifying the system identification algorithms for use with input/output data files. It provides a history of the theoretical, algorithmic and software development efforts including operating system requirements and listings of some of the various special purpose subroutines which were developed and optimized for Lahey FORTRAN compilers on IBM PC-AT computers before the subroutines were integrated into the system software. Potential purchasers are encouraged to purchase and review the documentation before purchasing the AU-FREDI software. AU-FREDI is distributed in DEC VAX BACKUP format on a 1600 BPI 9-track magnetic tape (standard media) or a TK50 tape cartridge. AU-FREDI was developed in 1989 and is a copyrighted work with all copyright vested in NASA.

Improved Displacement Transfer Functions for Structure Deformed Shape Predictions Using Discretely Distributed Surface Strains

NASA Technical Reports Server (NTRS)

Ko, William L.; Fleischer, Van Tran

2012-01-01

In the formulations of earlier Displacement Transfer Functions for structure shape predictions, the surface strain distributions, along a strain-sensing line, were represented with piecewise linear functions. To improve the shape-prediction accuracies, Improved Displacement Transfer Functions were formulated using piecewise nonlinear strain representations. Through discretization of an embedded beam (depth-wise cross section of a structure along a strain-sensing line) into multiple small domains, piecewise nonlinear functions were used to describe the surface strain distributions along the discretized embedded beam. Such piecewise approach enabled the piecewise integrations of the embedded beam curvature equations to yield slope and deflection equations in recursive forms. The resulting Improved Displacement Transfer Functions, written in summation forms, were expressed in terms of beam geometrical parameters and surface strains along the strain-sensing line. By feeding the surface strains into the Improved Displacement Transfer Functions, structural deflections could be calculated at multiple points for mapping out the overall structural deformed shapes for visual display. The shape-prediction accuracies of the Improved Displacement Transfer Functions were then examined in view of finite-element-calculated deflections using different tapered cantilever tubular beams. It was found that by using the piecewise nonlinear strain representations, the shape-prediction accuracies could be greatly improved, especially for highly-tapered cantilever tubular beams.

Heat convection in a micro impinging jet system

NASA Astrophysics Data System (ADS)

Mai, John Dzung Hoang

2000-10-01

This thesis covers the development of an efficient micro impinging jet heat exchanger, using MEMS technology, to provide localized cooling for present and next generation microelectronic computer chips. Before designing an efficient localized heat exchanger, it is necessary to investigate fluid dynamics and heat transfer in the micro scale. MEMS technology has been used in this project because it is the only tool currently available that can provide a large array of batch-fabricated, micro-scale nozzles for localized cooling. Our investigation of potential MEMS heat exchanger designs begins with experiments that measure the pressure drops and temperature changes in a micro scale tubing system that will be necessary to carry fluid to the impingement point. Our basic MEMS model is a freestanding micro channel with integrated temperature microsensors. The temperature distribution along the channel in a vacuum is measured. The measured flow rates are compared with an analytical model developed for capillary flow that accounts for 2-D, slip and compressibility effects. The work is focused on obtaining correlations in the form of the Nussult number, the Reynolds number and a H/d geometric factor. A set of single MEMS nozzles have been designed to test heat transfer effectiveness as a function of nozzle diameter, ranging from 1.0 mm to 250 um. In addition, nozzle and slot array MEMS devices have been fabricated. In order to obtain quantitative measurements from these micron scale devices, a series of target temperature sensor chips were custom made and characterized for these experiments. The heat transfer characteristics of various MEMS nozzle configurations operating at various steady inlet pressures, at different heights above the heated substrate, have been characterized. These steady results showed that the average heat transfer coefficient, averaged over a 1 cm2 test area, was usually less than 0.035 W/cm 2K for any situation. However, the local heat transfer coefficient, as measured by a single 4mum x 4mum temperature sensor, was as high as 0.5 W/cm2K. Using a mechanical valve and piezo actuator to perturb the flow at frequencies from 10 Hz to 1 kHz, we identify that enhanced heat transfer can occur in an unsteady forced jet. The functional dependence of the enhanced heat transfer on the mean jet speed, perturbation level and perturbing frequency has been established. The expected trend that increased heat transfer at higher values of St number was noticed. In addition the effect of a confined and free jet geometry on an unsteady flow was observed.

A Systematic Review of Commercial Cognitive Training Devices: Implications for Use in Sport

PubMed Central

Harris, David J.; Wilson, Mark R.; Vine, Samuel J.

2018-01-01

Background: Cognitive training (CT) aims to develop a range of skills, like attention and decision-making, through targeted training of core cognitive functions. While CT can target context specific skills, like movement anticipation, much CT is domain general, focusing on core abilities (e.g., selective attention) for transfer to a range of real-world tasks, such as spotting opponents. Commercial CT (CCT) devices are highly appealing for athletes and coaches due to their ease of use and eye-catching marketing claims. The extent to which this training transfers to performance in the sporting arena is, however, unclear. Therefore, this paper sought to provide a systematic review of evidence for beneficial training effects of CCT devices and evaluate their application to sport. Methods: An extensive search of electronic databases (PubMed, PsychInfo, GoogleScholar, and SportDiscus) was conducted to identify peer-reviewed evidence of training interventions with commercially available CT devices. Forty-three studies met the inclusion criteria and were retained for quality assessment and synthesis of results. Seventeen studies assessed transfer effects beyond laboratory cognitive tests, but only 1 directly assessed transfer to a sporting task. Results: The review of evidence showed limited support for far transfer benefits from CCT devices to sporting tasks, mainly because studies did not target the sporting environment. Additionally, a number of methodological issues with the CCT literature were identified, including small sample sizes, lack of retention tests, and limited replication of findings by researchers independent of the commercial product. Therefore, evidence for sporting benefits is currently limited by the paucity of representative transfer tests and a focus on populations with health conditions. Conclusions: Currently there is little direct evidence that the use of CCT devices can transfer to benefits for sporting performance. This conclusion, however, stems more from a lack of experimental studies in the sporting field and a lack of experimental rigor, rather than convincing null effects. Subsequently, there is an opportunity for researchers to develop more reliable findings in this area through systematic assessment in athletic populations and major methodological improvements.

Towards programmable plant genetic circuits.

PubMed

Medford, June I; Prasad, Ashok

2016-07-01

Synthetic biology enables the construction of genetic circuits with predictable gene functions in plants. Detailed quantitative descriptions of the transfer function or input-output function for genetic parts (promoters, 5' and 3' untranslated regions, etc.) are collected. These data are then used in computational simulations to determine their robustness and desired properties, thereby enabling the best components to be selected for experimental testing in plants. In addition, the process forms an iterative workflow which allows vast improvement to validated elements with sub-optimal function. These processes enable computational functions such as digital logic in living plants and follow the pathway of technological advances which took us from vacuum tubes to cell phones. © 2016 The Authors The Plant Journal © 2016 John Wiley & Sons Ltd.

Spectral response analysis of PVDF capacitive sensors

NASA Astrophysics Data System (ADS)

Reyes-Ramírez, B.; García-Segundo, C.; García-Valenzuela, A.

2013-06-01

We investigate the spectral response to ultrasound waves in water of low-noise capacitive sensors based on PVDF polymer piezoelectric films. First, we analyze theoretically the mechanical-to-electrical transduction as a function of the frequency of ultrasonic signals and derive an analytic expression of the sensor's transfer function. Then we present experimental results of the frequency response of a home-made PDVF in water to test signals from 1 to 20 MHz induced by a commercial hydrophone powered by a signal generator and compare with our theoretical model.

Does test-enhanced learning transfer for triple associates?

PubMed

Pan, Steven C; Wong, Carol M; Potter, Zachary E; Mejia, Jonathan; Rickard, Timothy C

2016-01-01

Test-enhanced learning and transfer for triple-associate word stimuli was assessed in three experiments. In each experiment, training and final-test trials involved the presentation of two words per triple associate (triplet), with the third word having to be retrieved. In agreement with the prior literature on different stimuli, training through testing with feedback yielded markedly better final-test performance than did restudy. However, in contrast to the positive transfer reported for paired associate stimuli, minimal or no positive transfer was observed, relative to a restudy control, from a trained cue combination (e.g., A, B, ?) to other cue combinations from the same triplet that required a different response (e.g., B, C, ?). That result also held when two unique cue combinations per triplet were tested during training, and for triplets with low and high average associative strengths. Supplementary analyses provided insight into the overall transfer effect: An incorrect response during training appears to yield positive transfer relative to restudy, whereas a correct response appears to yield no, or even negative, transfer. Cross-experiment analyses indicated that test-enhanced learning is not diminished when two or three cue combinations are presented during training. Thus, even though learning through testing is highly specific, testing on all possible stimulus-response combinations remains the most efficient strategy for the learning of triple associates.

Heat transfer in pipes

NASA Technical Reports Server (NTRS)

Burbach, T.

1985-01-01

The heat transfer from hot water to a cold copper pipe in laminar and turbulent flow condition is determined. The mean flow through velocity in the pipe, relative test length and initial temperature in the vessel were varied extensively during tests. Measurements confirm Nusselt's theory for large test lengths in laminar range. A new equation is derived for heat transfer for large starting lengths which agrees satisfactorily with measurements for large starting lengths. Test results are compared with the new Prandtl equation for heat transfer and correlated well. Test material for 200- and to 400-diameter test length is represented at four different vessel temperatures.

Electronic structure and charge transfer excited states of endohedral fullerene containing electron donoracceptor complexes utilized in organic photovoltaics

NASA Astrophysics Data System (ADS)

Amerikheirabadi, Fatemeh

Organic Donor-Acceptor complexes form the main component of the organic photovoltaic devices (OPVs). The open circuit voltage of OPVs is directly related to the charge transfer excited state energies of these complexes. Currently a large number of different molecular complexes are being tested for their efficiency in photovoltaic devices. In this work, density functional theory as implemented in the NRLMOL code is used to investigate the electronic structure and related properties of these donor-acceptor complexes. The charge transfer excitation energies are calculated using the perturbative delta self-consistent field method recently developed in our group as the standard time dependent density functional approaches fail to accurately provide them. The model photovoltaics systems analyzed are as follows: Sc3N C 80--ZnTPP, Y3 N C80-- ZnTPP and Sc3 N C80-- ZnPc. In addition, a thorough analysis of the isolated donor and acceptor molecules is also provided. The studied acceptors are chosen from a class of fullerenes named trimetallic nitride endohedral fullerenes. These molecules have shown to possess advantages as acceptors such as long lifetimes of the charge-separated states.

Music training and inhibitory control: a multidimensional model.

PubMed

Moreno, Sylvain; Farzan, Faranak

2015-03-01

Training programs aimed to improve cognitive skills have either yielded mixed results or remain to be validated. The limited benefits of such regimens are largely attributable to weak understanding of (1) how (and which) interventions provide the most cognitive improvements; and (2) how brain networks and neural mechanisms that underlie specific cognitive abilities can be modified selectively. Studies indicate that music training leads to robust and long-lasting benefits to behavior. Importantly, behavioral advantages conferred by music extend beyond perceptual abilities to even nonauditory functions, such as inhibitory control (IC) and its neural correlates. Alternative forms of arts engagement or brain training do not appear to yield such enhancements, which suggests that music uniquely taps into brain networks subserving a variety of auditory as well as domain-general mechanisms such as IC. To account for such widespread benefits of music training, we propose a framework of transfer effects characterized by three dimensions: level of processing, nature of the transfer, and involvement of executive functions. We suggest that transfer of skills is mediated through modulation of general cognitive processes, in particular IC. We believe that this model offers a viable framework to test the extent and limitations of music-related changes. © 2014 New York Academy of Sciences.

Extracting electron transfer coupling elements from constrained density functional theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu Qin; Van Voorhis, Troy

2006-10-28

Constrained density functional theory (DFT) is a useful tool for studying electron transfer (ET) reactions. It can straightforwardly construct the charge-localized diabatic states and give a direct measure of the inner-sphere reorganization energy. In this work, a method is presented for calculating the electronic coupling matrix element (H{sub ab}) based on constrained DFT. This method completely avoids the use of ground-state DFT energies because they are known to irrationally predict fractional electron transfer in many cases. Instead it makes use of the constrained DFT energies and the Kohn-Sham wave functions for the diabatic states in a careful way. Test calculationsmore » on the Zn{sub 2}{sup +} and the benzene-Cl atom systems show that the new prescription yields reasonable agreement with the standard generalized Mulliken-Hush method. We then proceed to produce the diabatic and adiabatic potential energy curves along the reaction pathway for intervalence ET in the tetrathiafulvalene-diquinone (Q-TTF-Q) anion. While the unconstrained DFT curve has no reaction barrier and gives H{sub ab}{approx_equal}17 kcal/mol, which qualitatively disagrees with experimental results, the H{sub ab} calculated from constrained DFT is about 3 kcal/mol and the generated ground state has a barrier height of 1.70 kcal/mol, successfully predicting (Q-TTF-Q){sup -} to be a class II mixed-valence compound.« less

Bilateral transfer phenomenon: A functional magnetic resonance imaging pilot study of healthy subjects.

PubMed

Uggetti, Carla; Ausenda, Carlo D; Squarza, Silvia; Cadioli, Marcello; Grimoldi, Ludovico; Cerri, Cesare; Cariati, Maurizio

2016-08-01

The bilateral transfer of a motor skill is a physiological phenomenon: the development of a motor skill with one hand can trigger the development of the same ability of the other hand. The purpose of this study was to verify whether bilateral transfer is associated with a specific brain activation pattern using functional magnetic resonance imaging (fMRI). The motor task was implemented as the execution of the Nine Hole Peg Test. Fifteen healthy subjects (10 right-handers and five left-handers) underwent two identical fMRI runs performing the motor task with the non-dominant hand. Between the first and the second run, each subject was intensively trained for five minutes to perform the same motor task with the dominant hand. Comparing the two functional scans across the pool of subjects, a change of the motor activation pattern was observed. In particular, we observed, in the second run, a change in the activation pattern both in the cerebellum and in the cerebral cortex. We found activations in cortical areas involved in somatosensory integration, areas involved in procedural memory. Our study shows, in a small group of healthy subjects, the modification of the fMRI activation pathway of a motor task performed by the non-dominant hand after intensive exercise performing the same task with the dominant hand. © The Author(s) 2016.

Evaluation of nerve transfer options for treating total brachial plexus avulsion injury: a retrospective study of 73 participants

PubMed Central

Gao, Kai-ming; Hu, Jing-jing; Lao, Jie; Zhao, Xin

2018-01-01

Despite recent great progress in diagnosis and microsurgical repair, the prognosis in total brachial plexus-avulsion injury remains unfavorable. Insufficient number of donors and unreasonable use of donor nerves might be key factors. To identify an optimal treatment strategy for this condition, we conducted a retrospective review. Seventy-three patients with total brachial plexus avulsion injury were followed up for an average of 7.3 years. Our analysis demonstrated no significant difference in elbow-flexion recovery between phrenic nerve-transfer (25 cases), phrenic nerve-graft (19 cases), intercostal nerve (17 cases), or contralateral C7-transfer (12 cases) groups. Restoration of shoulder function was attempted through anterior accessory nerve (27 cases), posterior accessory nerve (10 cases), intercostal nerve (5 cases), or accessory + intercostal nerve transfer (31 cases). Accessory nerve + intercostal nerve transfer was the most effective method. A significantly greater amount of elbow extension was observed in patients with intercostal nerve transfer (25 cases) than in those with contralateral C7 transfer (10 cases). Recovery of median nerve function was noticeably better for those who received entire contralateral C7 transfer (33 cases) than for those who received partial contralateral C7 transfer (40 cases). Wrist and finger extension were reconstructed by intercostal nerve transfer (31 cases). Overall, the recommended surgical treatment for total brachial plexus-avulsion injury is phrenic nerve transfer for elbow flexion, accessory nerve + intercostal nerve transfer for shoulder function, intercostal nerves transfer for elbow extension, entire contralateral C7 transfer for median nerve function, and intercostal nerve transfer for finger extension. The trial was registered at ClinicalTrials.gov (identifier: NCT03166033). PMID:29623932

Evaluation of nerve transfer options for treating total brachial plexus avulsion injury: A retrospective study of 73 participants.

PubMed

Gao, Kai-Ming; Hu, Jing-Jing; Lao, Jie; Zhao, Xin

2018-03-01

Despite recent great progress in diagnosis and microsurgical repair, the prognosis in total brachial plexus-avulsion injury remains unfavorable. Insufficient number of donors and unreasonable use of donor nerves might be key factors. To identify an optimal treatment strategy for this condition, we conducted a retrospective review. Seventy-three patients with total brachial plexus avulsion injury were followed up for an average of 7.3 years. Our analysis demonstrated no significant difference in elbow-flexion recovery between phrenic nerve-transfer (25 cases), phrenic nerve-graft (19 cases), intercostal nerve (17 cases), or contralateral C 7 -transfer (12 cases) groups. Restoration of shoulder function was attempted through anterior accessory nerve (27 cases), posterior accessory nerve (10 cases), intercostal nerve (5 cases), or accessory + intercostal nerve transfer (31 cases). Accessory nerve + intercostal nerve transfer was the most effective method. A significantly greater amount of elbow extension was observed in patients with intercostal nerve transfer (25 cases) than in those with contralateral C 7 transfer (10 cases). Recovery of median nerve function was noticeably better for those who received entire contralateral C 7 transfer (33 cases) than for those who received partial contralateral C 7 transfer (40 cases). Wrist and finger extension were reconstructed by intercostal nerve transfer (31 cases). Overall, the recommended surgical treatment for total brachial plexus-avulsion injury is phrenic nerve transfer for elbow flexion, accessory nerve + intercostal nerve transfer for shoulder function, intercostal nerves transfer for elbow extension, entire contralateral C 7 transfer for median nerve function, and intercostal nerve transfer for finger extension. The trial was registered at ClinicalTrials.gov (identifier: NCT03166033).

Designing Artificial Neural Networks Using Particle Swarm Optimization Algorithms

PubMed Central

Vázquez, Roberto A.

2015-01-01

Artificial Neural Network (ANN) design is a complex task because its performance depends on the architecture, the selected transfer function, and the learning algorithm used to train the set of synaptic weights. In this paper we present a methodology that automatically designs an ANN using particle swarm optimization algorithms such as Basic Particle Swarm Optimization (PSO), Second Generation of Particle Swarm Optimization (SGPSO), and a New Model of PSO called NMPSO. The aim of these algorithms is to evolve, at the same time, the three principal components of an ANN: the set of synaptic weights, the connections or architecture, and the transfer functions for each neuron. Eight different fitness functions were proposed to evaluate the fitness of each solution and find the best design. These functions are based on the mean square error (MSE) and the classification error (CER) and implement a strategy to avoid overtraining and to reduce the number of connections in the ANN. In addition, the ANN designed with the proposed methodology is compared with those designed manually using the well-known Back-Propagation and Levenberg-Marquardt Learning Algorithms. Finally, the accuracy of the method is tested with different nonlinear pattern classification problems. PMID:26221132

Proactive interference by cues presented without outcomes: Differences in context specificity of latent inhibition and conditioned inhibition.

PubMed

Miguez, Gonzalo; McConnell, Bridget; Polack, Cody W; Miller, Ralph R

2018-01-08

This report is part of a larger project examining associative interference as a function of the nature of the interfering and target associations. Lick suppression experiments with rats assessed the effects of context shifts on proactive outcome interference by latent inhibition (LI) and Pavlovian conditioned inhibition (CI) treatments on subsequently trained Pavlovian conditioned excitation treatment. LI and CI were trained in Context A during Phase 1, and then excitation treatment was administered in Context B during Phase 2, followed by tests for conditioned excitation in Contexts A, B, or C. Experiment 1 preliminarily established our LI and CI treatments and resulted in equally retarded acquisition of behavioral control when the target cue was subsequently trained as a conditioned excitor and tested in Context A. However, only CI treatment caused the target to pass a summation test for inhibition. Centrally, Experiment 2 consisted of LI and CI treatments in Context A followed by excitatory training in Context B. Testing found low excitatory control by both LI and CI cues in Context A relative to strong excitatory control in Context B, but CI treatment transferred to Context C more strongly than LI treatment. Experiment 3 determined that LI treatment failed to transfer to Context C even when the number of LI trials was greatly increased. Thus, first-learned LI appears to be relatively context specific, whereas first-learned CI generalizes to a neutral context. These observations add to existing evidence that LI and CI treatments result in different types of learning that diverge sharply in transfer to a novel test context.

Radiology compared with xenon—133 scanning and bronchoscopic lobar sampling as methods for assessing regional lung function in patients with emphysema

PubMed Central

Barter, C. E.; Hugh-Jones, P.; Laws, J. W.; Crosbie, W. A.

1973-01-01

Regional lung function was assessed by radiographic methods, by regional function studies using xenon-133 scans, and by lobar sampling with a mass spectrometer flow-meter at bronchoscopy in 12 patients who subsequently had bullae resected at operation. The information given by these three methods of regional assessment was subsequently compared with the findings at operation. When only one lobe was abnormal on the radiographs, these alone were adequate to locate the major site of the emphysema and the regional tests gave relatively little extra information. The xenon scan was sometimes helpful in assessing the state of the remaining lung, but this information could be deduced from the radiographs and overall lung function tests, especially the carbon monoxide transfer and mechanical measurements. Bronchoscopic sampling was helpful in determining whether the affected lobe was acting as a ventilated dead-space. When more than one lobe was affected the regional function tests supplemented the radiographs in defining the site of bullous change as well as locating dead space. Xenon scans, although widely employed for such preoperative assessments, added little to the topographical information obtained by careful radiology. The combination of radiology, lobar sampling, and overall function tests is recommended for assessing which emphysematous patients are likely to benefit from surgery. Images PMID:4685209

Molecular changes in hepatic metabolism and transport in cirrhosis and their functional importance

PubMed Central

Dietrich, Christoph G; Götze, Oliver; Geier, Andreas

2016-01-01

Liver cirrhosis is the common endpoint of many hepatic diseases and represents a relevant risk for liver failure and hepatocellular carcinoma. The progress of liver fibrosis and cirrhosis is accompanied by deteriorating liver function. This review summarizes the regulatory and functional changes in phase I and phase II metabolic enzymes as well as transport proteins and provides an overview regarding lipid and glucose metabolism in cirrhotic patients. Interestingly, phase I enzymes are generally downregulated transcriptionally, while phase II enzymes are mostly preserved transcriptionally but are reduced in their function. Transport proteins are regulated in a specific way that resembles the molecular changes observed in obstructive cholestasis. Lipid and glucose metabolism are characterized by insulin resistance and catabolism, leading to the disturbance of energy expenditure and wasting. Possible non-invasive tests, especially breath tests, for components of liver metabolism are discussed. The heterogeneity and complexity of changes in hepatic metabolism complicate the assessment of liver function in individual patients. Additionally, studies in humans are rare, and species differences preclude the transferability of data from rodents to humans. In clinical practice, some established global scores or criteria form the basis for the functional evaluation of patients with liver cirrhosis, but difficult treatment decisions such as selection for transplantation or resection require further research regarding the application of existing non-invasive tests and the development of more specific tests. PMID:26755861

Hip Abductor Strengthening Improves Physical Function Following Total Knee Replacement: One-Year Follow-Up of a Randomized Pilot Study.

PubMed

Harikesavan, Karvannan; Chakravarty, Raj D; Maiya, Arun G; Hegde, Sanjay P; Y Shivanna, Shivakumar

2017-01-01

Total knee replacement (TKR) is the commonest surgical procedure for patients with severe pain and impaired physical function following end stage knee osteoarthritis. The hip abductors are well renowned in stabilization of the trunk and hip during walking, maintaining the lower limb position, and transferring the forces from the lower limbs to the pelvis. To assess the efficacy of hip abductor strengthening exercise on functional outcome using performance based outcome measures following total knee replacement. An observer blinded randomized pilot trial design was conducted at Manipal hospital, Bangalore, India. Participants designated for elective TKR were randomized to experimental group hip abductor strengthening along with standard rehabilitation (n=10) or control group standard rehabilitation alone (n=10). Participants followed for one year to assess physical function using performance based outcomes, such as timed up and go test, single leg stance test, six minute walk test, knee extensor strength and hip abductor strength. Eighteen participants with a mean age of 63.1 ± 5.5 years (8 Males and 10 Females) completed the study. Improvement in hip abduction strength, single leg stand test was superior in hip abductor strengthening group at 3 months and 1 year when compared to standard rehabilitation alone. Hip abductor strengthening showed superior improvements in single leg stance test and six minute walk test. Hip abductor strengthening exercises has the potential to improve physical function following total knee replacement.

Hip Abductor Strengthening Improves Physical Function Following Total Knee Replacement: One-Year Follow-Up of a Randomized Pilot Study

PubMed Central

Harikesavan, Karvannan; Chakravarty, Raj D.; Maiya, Arun G; Hegde, Sanjay P.; Y. Shivanna, Shivakumar

2017-01-01

Background: Total knee replacement (TKR) is the commonest surgical procedure for patients with severe pain and impaired physical function following end stage knee osteoarthritis. The hip abductors are well renowned in stabilization of the trunk and hip during walking, maintaining the lower limb position, and transferring the forces from the lower limbs to the pelvis. Objective: To assess the efficacy of hip abductor strengthening exercise on functional outcome using performance based outcome measures following total knee replacement. Methods: An observer blinded randomized pilot trial design was conducted at Manipal hospital, Bangalore, India. Participants designated for elective TKR were randomized to experimental group hip abductor strengthening along with standard rehabilitation (n=10) or control group standard rehabilitation alone (n=10). Participants followed for one year to assess physical function using performance based outcomes, such as timed up and go test, single leg stance test, six minute walk test, knee extensor strength and hip abductor strength. Result: Eighteen participants with a mean age of 63.1 ± 5.5 years (8 Males and 10 Females) completed the study. Improvement in hip abduction strength, single leg stand test was superior in hip abductor strengthening group at 3 months and 1 year when compared to standard rehabilitation alone. Conclusion: Hip abductor strengthening showed superior improvements in single leg stance test and six minute walk test. Hip abductor strengthening exercises has the potential to improve physical function following total knee replacement. PMID:28567148

5 CFR 630.212 - Use of annual leave to establish initial eligibility for retirement or continuation of health...

Code of Federal Regulations, 2010 CFR

2010-01-01

... decline relocation (including transfer of function). (b)(1) Annual leave that may be used for the purposes... transfer of function) and annual leave earned by an employee while in a paid leave status after the effective date of the reduction in force or relocation (including transfer of function). (2) Annual leave...

Dispersion relations of elastic waves in one-dimensional piezoelectric/piezomagnetic phononic crystal with functionally graded interlayers.

PubMed

Guo, Xiao; Wei, Peijun; Lan, Man; Li, Li

2016-08-01

The effects of functionally graded interlayers on dispersion relations of elastic waves in a one-dimensional piezoelectric/piezomagnetic phononic crystal are studied in this paper. First, the state transfer equation of the functionally graded interlayer is derived from the motion equation by the reduction of order (from second order to first order). The transfer matrix of the functionally graded interlayer is obtained by solving the state transfer equation with the spatial-varying coefficient. Based on the transfer matrixes of the piezoelectric slab, the piezomagnetic slab and the functionally graded interlayers, the total transfer matrix of a single cell is obtained. Further, the Bloch theorem is used to obtain the resultant dispersion equations of in-plane and anti-plane Bloch waves. The dispersion equations are solved numerically and the numerical results are shown graphically. Five kinds of profiles of functionally graded interlayers between a piezoelectric slab and a piezomagnetic slab are considered. It is shown that the functionally graded interlayers have evident influences on the dispersion curves and the band gaps. Copyright © 2016 Elsevier B.V. All rights reserved.

Variable-Domain Displacement Transfer Functions for Converting Surface Strains into Deflections for Structural Deformed Shape Predictions

NASA Technical Reports Server (NTRS)

Ko, William L.; Fleischer, Van Tran

2015-01-01

Variable-Domain Displacement Transfer Functions were formulated for shape predictions of complex wing structures, for which surface strain-sensing stations must be properly distributed to avoid jointed junctures, and must be increased in the high strain gradient region. Each embedded beam (depth-wise cross section of structure along a surface strain-sensing line) was discretized into small variable domains. Thus, the surface strain distribution can be described with a piecewise linear or a piecewise nonlinear function. Through discretization, the embedded beam curvature equation can be piece-wisely integrated to obtain the Variable-Domain Displacement Transfer Functions (for each embedded beam), which are expressed in terms of geometrical parameters of the embedded beam and the surface strains along the strain-sensing line. By inputting the surface strain data into the Displacement Transfer Functions, slopes and deflections along each embedded beam can be calculated for mapping out overall structural deformed shapes. A long tapered cantilever tubular beam was chosen for shape prediction analysis. The input surface strains were analytically generated from finite-element analysis. The shape prediction accuracies of the Variable- Domain Displacement Transfer Functions were then determined in light of the finite-element generated slopes and deflections, and were fofound to be comparable to the accuracies of the constant-domain Displacement Transfer Functions

Modified Displacement Transfer Functions for Deformed Shape Predictions of Slender Curved Structures with Varying Curvatives

NASA Technical Reports Server (NTRS)

Ko, William L.; Fleischer, Van Tran

2014-01-01

To eliminate the need to use finite-element modeling for structure shape predictions, a new method was invented. This method is to use the Displacement Transfer Functions to transform the measured surface strains into deflections for mapping out overall structural deformed shapes. The Displacement Transfer Functions are expressed in terms of rectilinearly distributed surface strains, and contain no material properties. This report is to apply the patented method to the shape predictions of non-symmetrically loaded slender curved structures with different curvatures up to a full circle. Because the measured surface strains are not available, finite-element analysis had to be used to analytically generate the surface strains. Previously formulated straight-beam Displacement Transfer Functions were modified by introducing the curvature-effect correction terms. Through single-point or dual-point collocations with finite-elementgenerated deflection curves, functional forms of the curvature-effect correction terms were empirically established. The resulting modified Displacement Transfer Functions can then provide quite accurate shape predictions. Also, the uniform straight-beam Displacement Transfer Function was applied to the shape predictions of a section-cut of a generic capsule (GC) outer curved sandwich wall. The resulting GC shape predictions are quite accurate in partial regions where the radius of curvature does not change sharply.

A Non-parametric Approach to Constrain the Transfer Function in Reverberation Mapping

NASA Astrophysics Data System (ADS)

Li, Yan-Rong; Wang, Jian-Min; Bai, Jin-Ming

2016-11-01

Broad emission lines of active galactic nuclei stem from a spatially extended region (broad-line region, BLR) that is composed of discrete clouds and photoionized by the central ionizing continuum. The temporal behaviors of these emission lines are blurred echoes of continuum variations (I.e., reverberation mapping, RM) and directly reflect the structures and kinematic information of BLRs through the so-called transfer function (also known as the velocity-delay map). Based on the previous works of Rybicki and Press and Zu et al., we develop an extended, non-parametric approach to determine the transfer function for RM data, in which the transfer function is expressed as a sum of a family of relatively displaced Gaussian response functions. Therefore, arbitrary shapes of transfer functions associated with complicated BLR geometry can be seamlessly included, enabling us to relax the presumption of a specified transfer function frequently adopted in previous studies and to let it be determined by observation data. We formulate our approach in a previously well-established framework that incorporates the statistical modeling of continuum variations as a damped random walk process and takes into account long-term secular variations which are irrelevant to RM signals. The application to RM data shows the fidelity of our approach.

Boundary layer development as a function of chamber pressure in the NASA Lewis 1030:1 area ratio rocket nozzle

NASA Technical Reports Server (NTRS)

Smith, Tamara A.

1988-01-01

Through the use of theoretical predictions of fluid properties and experimental heat transfer and thrust measurements, the zones of laminar, transitional, and turbulent boundary layer flow were defined for the NASA Lewis 1039:1 area ratio rocket nozzle. Tests were performed on the nozzle at chamber pressures from 350 to 100 psia. For these conditions, the throat diameter Reynolds numbers varied from 300,000 to 1 million. The propellants used were gaseous hydrogen and gaseous oxygen. Thrust measurements and nozzle outer wall temperature measurements were taken during the 3-sec test runs. Comparison of experimental heat transfer and thrust data with the corresponding predictions from the Two-Dimensional Kinetics (TDK) nozzle analysis program indicated laminar flow in the nozzle at a throat diameter Reynolds number of 320,000 or chamber pressure of 360 psia. Comparison of experimental and predicted heat transfer data indicated transitional flow up to and including a chamber pressure of 1000 psia. Predicted values of the axisymmetric acceleration parameter within the convergent and divergent nozzle were consistent with the above results. Based upon an extrapolation of the heat transfer data and predicted distributions of the axisymmetric acceleration parameter, transitional flow was predicted up to a throat diameter Reynolds number of 220,000 or 2600-psia chamber pressure. Above 2600-psia chamber pressure, fully developed turbulent flow was predicted.

Boundary layer development as a function of chamber pressure in the NASA Lewis 1030:1 area ratio rocket nozzle

NASA Technical Reports Server (NTRS)

Smith, Tamara A.

1988-01-01

Through the use of theoretical predictions of fluid properties and experimental heat transfer and thrust measurements, the zones of laminar, transitional, and turbulent boundary layer flow were defined for the NASA Lewis 1030:1 area ratio rocket nozzle. Tests were performed on the nozzle at chamber pressures from 350 to 100 psia. For these conditions, the throat diameter Reynolds numbers varied from 300,000 to 1 million. The propellants used were gaseous hydrogen and gaseous oxygen. Thrust measurements and nozzle outer wall temperature measurements were taken during the 3-sec test runs. Comparison of experimental heat transfer and thrust data with the corresponding predictions from the Two-Dimensional Kinetics (TDK) nozzle analysis program indicated laminar flow in the nozzle at a throat diameter Reynolds number of 320,000 or chamber pressure of 360 psia. Comparison of experimental and predicted heat transfer data indicated transitional flow up to and including a chamber pressure of 1000 psia. Predicted values of the axisymmetric acceleration parameter within the convergent and divergent nozzle were consistent with the above results. Based upon an extrapolation of the heat transfer data and predicted distributions of the axisymmetric acceleration parameter, transitional flow was predicted up to a throat diameter Reynolds number of 220,000 or 2600-psia chamber pressure. Above 2600-psia chamber pressure, fully developed turbulent flow was predicted.

Systems of meaning and transference: Implicit significant-other activation evokes shared reality.

PubMed

Przybylinski, Elizabeth; Andersen, Susan M

2015-10-01

Evidence shows that representations of significant others (SOs) are used in interpersonal relations-for example, in the social-cognitive process of transference (see Andersen & Chen, 2002), a process that is assumed to serve meaning-making functions (Glassman & Andersen, 1999b). Five studies tested the more specific notion that implicit activation of an SO representation in transference should indirectly activate the worldview shared with the SO, leading to its active pursuit, validation, and protection. Shared worldviews were assessed beforehand, both idiographically, as values (Studies 1 and 4), and nomothetically, as political ideology or religious beliefs (Studies 2, 3, and 5). In each experiment, participants learned about new persons, one subtly resembling their own SO. Transference was assessed (memory bias; positive evaluation; see Andersen, Reznik, & Manzella, 1996) and, crucially, as predicted, when considering the new person resembling their SO (vs. the control persons), participants showed faster response latencies in a lexical decision task to words reflecting the worldview shared with the SO (vs. held only personally, Studies 1-3, or only by the SO, Study 3). With this person, they also anticipated a more meaningful interaction and actively socially tuned to the SO-shared worldview, selecting conversation topics reflecting the SO-shared worldview (vs. personally held or SO-held topics, Studies 1-3). Finally, threatening the SO-shared worldview with this person (vs. threatening personally held, SO-held, or irrelevant worldviews) prompted goal activation to restore the disrupted meaning (Studies 4 and 5), assessed by response latency in a lexical decision task. Transference thus evokes shared meaning systems and serves epistemic functions. (c) 2015 APA, all rights reserved).

An improved ray theory and transfer matrix method-based model for lightning electromagnetic pulses propagating in Earth-ionosphere waveguide and its applications

NASA Astrophysics Data System (ADS)

Qin, Zilong; Chen, Mingli; Zhu, Baoyou; Du, Ya-ping

2017-01-01

An improved ray theory and transfer matrix method-based model for a lightning electromagnetic pulse (LEMP) propagating in Earth-ionosphere waveguide (EIWG) is proposed and tested. The model involves the presentation of a lightning source, parameterization of the lower ionosphere, derivation of a transfer function representing all effects of EIWG on LEMP sky wave, and determination of attenuation mode of the LEMP ground wave. The lightning source is simplified as an electric point dipole standing on Earth surface with finite conductance. The transfer function for the sky wave is derived based on ray theory and transfer matrix method. The attenuation mode for the ground wave is solved from Fock's diffraction equations. The model is then applied to several lightning sferics observed in central China during day and night times within 1000 km. The results show that the model can precisely predict the time domain sky wave for all these observed lightning sferics. Both simulations and observations show that the lightning sferics in nighttime has a more complicated waveform than in daytime. Particularly, when a LEMP propagates from east to west (Φ = 270°) and in nighttime, its sky wave tends to be a double-peak waveform (dispersed sky wave) rather than a single peak one. Such a dispersed sky wave in nighttime may be attributed to the magneto-ionic splitting phenomenon in the lower ionosphere. The model provides us an efficient way for retrieving the electron density profile of the lower ionosphere and hence to monitor its spatial and temporal variations via lightning sferics.

The estimation of the rates of lead exchange between body compartments of smelter employees.

PubMed

Behinaein, Sepideh; Chettle, David R; Egden, Lesley M; McNeill, Fiona E; Norman, Geoff; Richard, Norbert; Stever, Susan

2014-07-01

The overwhelming proportion of the mass of lead (Pb) is stored in bone and the residence time of Pb in bone is much longer than that in other tissues. Hence, in a metabolic model that we used to solve the differential equations governing the transfer of lead between body compartments, three main compartments are involved: blood (as a transfer compartment), cortical bone (tibia), and trabecular bone (calcaneus). There is a bidirectional connection between blood and the other two compartments. A grid search chi-squared minimization method was used to estimate the initial values of lead transfer rate values from tibia (λTB) and calcaneus (λCB) to blood of 209 smelter employees whose bone lead measurements are available from 1994, 1999, and 2008, and their blood lead level from 1967 onwards (depending on exposure history from once per month to once per year), and then the initial values of kinematic parameters were used to develop multivariate models in order to express λTB and λCB as a function of employment time, age, body lead contents and their interaction. We observed a significant decrease in the transfer rate of lead from bone to blood with increasing body lead contents. The model was tested by calculating the bone lead concentration in 1999 and 2008, and by comparing those values with the measured ones. A good agreement was found between the calculated and measured tibia/calcaneus lead values. Also, we found that the transfer rate of lead from tibia to blood can be expressed solely as a function of cumulative blood lead index.

Optical design and testing: introduction.

PubMed

Liang, Chao-Wen; Koshel, John; Sasian, Jose; Breault, Robert; Wang, Yongtian; Fang, Yi Chin

2014-10-10

Optical design and testing has numerous applications in industrial, military, consumer, and medical settings. Assembling a complete imaging or nonimage optical system may require the integration of optics, mechatronics, lighting technology, optimization, ray tracing, aberration analysis, image processing, tolerance compensation, and display rendering. This issue features original research ranging from the optical design of image and nonimage optical stimuli for human perception, optics applications, bio-optics applications, 3D display, solar energy system, opto-mechatronics to novel imaging or nonimage modalities in visible and infrared spectral imaging, modulation transfer function measurement, and innovative interferometry.

A new energy transfer model for turbulent free shear flow

NASA Technical Reports Server (NTRS)

Liou, William W.-W.

1992-01-01

A new model for the energy transfer mechanism in the large-scale turbulent kinetic energy equation is proposed. An estimate of the characteristic length scale of the energy containing large structures is obtained from the wavelength associated with the structures predicted by a weakly nonlinear analysis for turbulent free shear flows. With the inclusion of the proposed energy transfer model, the weakly nonlinear wave models for the turbulent large-scale structures are self-contained and are likely to be independent flow geometries. The model is tested against a plane mixing layer. Reasonably good agreement is achieved. Finally, it is shown by using the Liapunov function method, the balance between the production and the drainage of the kinetic energy of the turbulent large-scale structures is asymptotically stable as their amplitude saturates. The saturation of the wave amplitude provides an alternative indicator for flow self-similarity.

Transferable Force Field for Metal–Organic Frameworks from First-Principles: BTW-FF

PubMed Central

2014-01-01

We present an ab-initio derived force field to describe the structural and mechanical properties of metal–organic frameworks (or coordination polymers). The aim is a transferable interatomic potential that can be applied to MOFs regardless of metal or ligand identity. The initial parametrization set includes MOF-5, IRMOF-10, IRMOF-14, UiO-66, UiO-67, and HKUST-1. The force field describes the periodic crystal and considers effective atomic charges based on topological analysis of the Bloch states of the extended materials. Transferable potentials were developed for the four organic ligands comprising the test set and for the associated Cu, Zn, and Zr metal nodes. The predicted materials properties, including bulk moduli and vibrational frequencies, are in agreement with explicit density functional theory calculations. The modal heat capacity and lattice thermal expansion are also predicted. PMID:25574157

Screening fungicides for use in fish culture: Evaluation of the agar plug transfer, cellophane transfer, and agar dilution methods

USGS Publications Warehouse

Bailey, Tom A.

1983-01-01

The reliability, reproducibility, and usefulness of three screening methods -- the cellophane transfer, the agar plug transfer, and the agar dilution -- to screen aquatic fungicides were evaluated. Achlya flagellata and Saprolegnia hypogyna were exposed to 1, 10, and 100 mg/L of malachite green to test each method. The cellophane transfer and agar plug transfer techniques had similar reliability and reproducibility in rating fungicidal activity, and were both superior to the agar dilution technique. The agar plug transfer and agar dilution techniques adequately projected in vivo activity of malachite green, but the cellophane transfer technique overestimated its activity. Overall, the agar plug transfer technique most accurately rated the activity of malachite green and was the easiest test to perform. It therefore appears to be the method of choice for testing aquatic fungicides.

Tail Service Mast Umbilical Arrival

NASA Image and Video Library

2016-08-02

A technician monitors the progress as a crane lifts the first Tail Service Mast Umbilical (TSMU) for transfer to a test stand at the Launch Equipment Test Facility at NASA’s Kennedy Space Center in Florida. Two TSMUs will provide liquid propellants and power to the Space Launch System (SLS) rocket’s core stage engine. Both TSMUs will connect to the zero-level deck on the mobile launcher, providing fuel and electricity to the SLS rocket before it launches on Exploration Mission 1. The TSMU will undergo testing and validation at the LETF to verify it is functioning properly. The center’s Engineering Directorate and the Ground Systems Development and Operations Program are overseeing processing and testing of the umbilicals.

Characterizing Behavioral and Brain Changes Associated with Practicing Reasoning Skills

PubMed Central

Mackey, Allyson P.; Miller Singley, Alison T.; Wendelken, Carter; Bunge, Silvia A.

2015-01-01

We have reported previously that intensive preparation for a standardized test that taxes reasoning leads to changes in structural and functional connectivity within the frontoparietal network. Here, we investigated whether reasoning instruction transfers to improvement on unpracticed tests of reasoning, and whether these improvements are associated with changes in neural recruitment during reasoning task performance. We found behavioral evidence for transfer to a transitive inference task, but no evidence for transfer to a rule generation task. Across both tasks, we observed reduced lateral prefrontal activation in the trained group relative to the control group, consistent with other studies of practice-related changes in brain activation. In the transitive inference task, we observed enhanced suppression of task-negative, or default-mode, regions, consistent with work suggesting that better cognitive skills are associated with more efficient switching between networks. In the rule generation task, we found a pattern consistent with a training-related shift in the balance between phonological and visuospatial processing. Broadly, we discuss general methodological considerations related to the analysis and interpretation of training-related changes in brain activation. In summary, we present preliminary evidence for changes in brain activation associated with practice of high-level cognitive skills. PMID:26368278

Automated Dissolution for Enteric-Coated Aspirin Tablets: A Case Study for Method Transfer to a RoboDis II.

PubMed

Ibrahim, Sarah A; Martini, Luigi

2014-08-01

Dissolution method transfer is a complicated yet common process in the pharmaceutical industry. With increased pharmaceutical product manufacturing and dissolution acceptance requirements, dissolution testing has become one of the most labor-intensive quality control testing methods. There is an increased trend for automation in dissolution testing, particularly for large pharmaceutical companies to reduce variability and increase personnel efficiency. There is no official guideline for dissolution testing method transfer from a manual, semi-automated, to automated dissolution tester. In this study, a manual multipoint dissolution testing procedure for an enteric-coated aspirin tablet was transferred effectively and reproducibly to a fully automated dissolution testing device, RoboDis II. Enteric-coated aspirin samples were used as a model formulation to assess the feasibility and accuracy of media pH change during continuous automated dissolution testing. Several RoboDis II parameters were evaluated to ensure the integrity and equivalency of dissolution method transfer from a manual dissolution tester. This current study provides a systematic outline for the transfer of the manual dissolution testing protocol to an automated dissolution tester. This study further supports that automated dissolution testers compliant with regulatory requirements and similar to manual dissolution testers facilitate method transfer. © 2014 Society for Laboratory Automation and Screening.

Toe-to-hand transfer in symbrachydactyly.

PubMed

Richardson, Philip W F; Johnstone, Bruce R; Coombs, Christopher J

2004-07-01

Symbrachydactyly, or central atypical cleft, is classified as a failure of formation. For the adactylous or monodactylous forms, free toe transfer is the treatment of choice. We present 18 free toe transfers in 13 patients for symbrachydactyly. Despite abnormal anatomy, the functional building blocks have always been available and transfer technically possible. The result has been improved function and high levels of parental satisfaction.

DISTRIBUTED RC NETWORKS WITH RATIONAL TRANSFER FUNCTIONS,

DTIC Science & Technology

A distributed RC circuit analogous to a continuously tapped transmission line can be made to have a rational short-circuit transfer admittance and...one rational shortcircuit driving-point admittance. A subcircuit of the same structure has a rational open circuit transfer impedance and one rational ...open circuit driving-point impedance. Hence, rational transfer functions may be obtained while considering either generator impedance or load

Mission analysis for cross-site transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riesenweber, S.D.; Fritz, R.L.; Shipley, L.E.

1995-11-01

The Mission Analysis Report describes the requirements and constraints associated with the Transfer Waste Function as necessary to support the Manage Tank Waste, Retrieve Waste, and Process Tank Waste Functions described in WHC-SD-WM-FRD-020, Tank Waste Remediation System (TWRS) Functions and Requirements Document and DOE/RL-92-60, Revision 1, TWRS Functions and Requirements Document, March 1994. It further assesses the ability of the ``initial state`` (or current cross-site transfer system) to meet the requirements and constraints.

Exercise in claudicants increase or decrease walking ability and the response relates to mitochondrial function.

PubMed

van Schaardenburgh, Michel; Wohlwend, Martin; Rognmo, Øivind; Mattsson, Erney J R

2017-06-07

Exercise of patients with intermittent claudication improves walking performance. Exercise does not usually increase blood flow, but seems to increase muscle mitochondrial enzyme activities. Although exercise is beneficial in most patients, it might be harmful in some. The mitochondrial response to exercise might therefore differ between patients. Our hypothesis was that changes in walking performance relate to changes in mitochondrial function after 8 weeks of exercise. At a subgroup level, negative responders decrease and positive responders increase mitochondrial capacity. Two types of exercise were studied, calf raising and walking (n = 28). We wanted to see whether there were negative and positive responders, independent of type of exercise. Measurements of walking performance, peripheral hemodynamics, mitochondrial respiration and content (citrate synthase activity) were obtained on each patient before and after the intervention period. Multiple linear regression was used to test whether changes in peak walking time relate to mitochondrial function. Subgroups of negative (n = 8) and positive responders (n = 8) were defined as those that either decreased or increased peak walking time following exercise. Paired t test and analysis of covariance was used to test changes within and between subgroups. Changes in peak walking time were related to changes in mitochondrial respiration supported by electron transferring flavoprotein (ETF + CI) P (p = 0.004), complex I (CI + ETF) P (p = 0.003), complex I + complex II (CI + CII + ETF) P (p = 0.037) and OXPHOS coupling efficiency (p = 0.046) in the whole group. Negative responders had more advanced peripheral arterial disease. Mitochondrial respiration supported by electron transferring flavoprotein (ETF + CI) P (p = 0.0013), complex I (CI + ETF) P (p = 0.0005), complex I + complex II (CI + CII + ETF) P (p = 0.011) and electron transfer system capacity (CI + CII + ETF) E (p = 0.021) and OXPHOS coupling efficiency decreased in negative responders (p = 0.0007) after exercise. Positive responders increased citrate synthase activity (p = 0.010). Changes in walking performance seem to relate to changes in mitochondrial function after exercise. Negative responders have more advanced peripheral arterial disease and decrease, while positive responders increase mitochondrial capacity. Trial registration ClinicalTrials.gov ID: NCT023110256.

33 CFR 150.405 - How must a cargo transfer system be tested and inspected?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false How must a cargo transfer system..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Cargo Transfer Operations § 150.405 How must a cargo transfer system be tested and inspected? (a) No person may transfer oil...

33 CFR 150.405 - How must a cargo transfer system be tested and inspected?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false How must a cargo transfer system..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Cargo Transfer Operations § 150.405 How must a cargo transfer system be tested and inspected? (a) No person may transfer oil...

33 CFR 150.405 - How must a cargo transfer system be tested and inspected?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false How must a cargo transfer system..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Cargo Transfer Operations § 150.405 How must a cargo transfer system be tested and inspected? (a) No person may transfer oil...

Characterization of the space shuttle reaction control system engine

NASA Technical Reports Server (NTRS)

Wilson, M. S.; Stechman, R. C.; Edelman, R. B.; Fortune, O. F.; Economos, C.

1972-01-01

A computer program was developed and written in FORTRAN 5 which predicts the transient and steady state performance and heat transfer characteristics of a pulsing GO2/GH2 rocket engine. This program predicts the dynamic flow and ignition characteristics which, when combined in a quasi-steady state manner with the combustion and mixing analysis program, will provide the thrust and specific impulse of the engine as a function of time. The program also predicts the transient and steady state heat transfer characteristics of the engine using various cooling concepts. The computer program, test case, and documentation are presented. The program is applicable to any system capable of utilizing the FORTRAN 4 or FORTRAN 5 language.

Thunder-induced ground motions: 1. Observations

NASA Astrophysics Data System (ADS)

Lin, Ting-L.; Langston, Charles A.

2009-04-01

Acoustic pressure from thunder and its induced ground motions were investigated using a small array consisting of five three-component short-period surface seismometers, a three-component borehole seismometer, and five infrasound microphones. We used the array to constrain wave parameters of the incident acoustic and seismic waves. The incident slowness differences between acoustic pressure and ground motions suggest that ground reverberations were first initiated somewhat away from the array. Using slowness inferred from ground motions is preferable to obtain the seismic source parameters. We propose a source equalization procedure for acoustic/seismic deconvolution to generate the time domain transfer function, a procedure similar to that of obtaining teleseismic earthquake receiver functions. The time domain transfer function removes the incident pressure time history from the seismogram. An additional vertical-to-radial ground motion transfer function was used to identify the Rayleigh wave propagation mode of induced seismic waves complementing that found using the particle motions and amplitude variations in the borehole. The initial motions obtained by the time domain transfer functions suggest a low Poisson's ratio for the near-surface layer. The acoustic-to-seismic transfer functions show a consistent reverberation series at frequencies near 5 Hz. This gives an empirical measure of site resonance that depends on the ratio of the layer velocity to layer thickness for earthquake P and S waves. The time domain transfer function approach by transferring a spectral division into the time domain provides an alternative method for studying acoustic-to-seismic coupling.

Functional Latissimus Dorsi Transfer for Upper-Extremity Reconstruction: A Case Report and Review of the Literature.

PubMed

Sood, Aditya; Therattil, Paul J; Russo, Gerardo; Lee, Edward S

2017-01-01

Objective: The latissimus dorsi flap is a workhorse for plastic surgeons, being used for many years for soft-tissue coverage of the upper extremity as well as for functional reconstruction to restore motion to the elbow and shoulder. The authors present a case of functional latissimus dorsi transfer for restoration of elbow flexion and review the literature on technique and outcomes. Methods: A literature review was performed using MEDLINE and the Cochrane Collaboration Library for primary research articles on functional latissimus dorsi flap transfer. Data related to surgical techniques and outcomes were extracted. Results: The literature search yielded 13 relevant studies, with a total of 52 patients who received pedicled, functional latissimus dorsi flaps for upper-extremity reconstruction. The most common etiology requiring reconstruction was closed brachial plexus injury (n = 13). After flap transfer, 98% of patients were able to flex the elbow against gravity and 82.3% were able to flex against resistance. In the presented case, a 77-year-old man underwent resection of myxofibrosarcoma of the upper arm with elbow prosthesis placement and functional latissimus dorsi transfer. The patient was able to actively flex against gravity at 3-month follow-up. Conclusions: A review of the literature shows that nearly all patients undergoing functional latissimus dorsi transfer for upper-extremity reconstruction regain at least motion against gravity whereas a large proportion regain motion against resistance. Considerations when planning for functional latissimus dorsi transfer include patient positioning, appropriate tensioning of the muscle, safe inset, polarity, management of other affected upper-extremity joints, and educating patients on the expected outcomes.

Functional Latissimus Dorsi Transfer for Upper-Extremity Reconstruction: A Case Report and Review of the Literature

PubMed Central

Therattil, Paul J.; Russo, Gerardo; Lee, Edward S.

2017-01-01

Objective: The latissimus dorsi flap is a workhorse for plastic surgeons, being used for many years for soft-tissue coverage of the upper extremity as well as for functional reconstruction to restore motion to the elbow and shoulder. The authors present a case of functional latissimus dorsi transfer for restoration of elbow flexion and review the literature on technique and outcomes. Methods: A literature review was performed using MEDLINE and the Cochrane Collaboration Library for primary research articles on functional latissimus dorsi flap transfer. Data related to surgical techniques and outcomes were extracted. Results: The literature search yielded 13 relevant studies, with a total of 52 patients who received pedicled, functional latissimus dorsi flaps for upper-extremity reconstruction. The most common etiology requiring reconstruction was closed brachial plexus injury (n = 13). After flap transfer, 98% of patients were able to flex the elbow against gravity and 82.3% were able to flex against resistance. In the presented case, a 77-year-old man underwent resection of myxofibrosarcoma of the upper arm with elbow prosthesis placement and functional latissimus dorsi transfer. The patient was able to actively flex against gravity at 3-month follow-up. Conclusions: A review of the literature shows that nearly all patients undergoing functional latissimus dorsi transfer for upper-extremity reconstruction regain at least motion against gravity whereas a large proportion regain motion against resistance. Considerations when planning for functional latissimus dorsi transfer include patient positioning, appropriate tensioning of the muscle, safe inset, polarity, management of other affected upper-extremity joints, and educating patients on the expected outcomes. PMID:28293330

Evaluation of Markov-Decision Model for Instructional Sequence Optimization. Semi-Annual Technical Report for the period 1 July-31 December 1975. Technical Report No. 76.

ERIC Educational Resources Information Center

Wollmer, Richard D.; Bond, Nicholas A.

Two computer-assisted instruction programs were written in electronics and trigonometry to test the Wollmer Markov Model for optimizing hierarchial learning; calibration samples totalling 110 students completed these programs. Since the model postulated that transfer effects would be a function of the amount of practice, half of the students were…

Hyperion 5113/GP Infrasound Sensor Evaluation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.

2015-08-01

Sandia National Laboratories has tested and evaluated an infrasound sensor, the 5113/GP manufactured by Hyperion. These infrasound sensors measure pressure output by a methodology developed by the University of Mississippi. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, transfer function, power, self-noise, dynamic range, and seismic sensitivity. These sensors are being evaluated prior to deployment by the U.S. Air Force.

Acute effects of ethanol on the transfer of nicotine and two dietary carcinogens in human placental perfusion.

PubMed

Veid, Jenni; Karttunen, Vesa; Myöhänen, Kirsi; Myllynen, Päivi; Auriola, Seppo; Halonen, Toivo; Vähäkangas, Kirsi

2011-09-10

Many mothers use, against instructions, alcohol during pregnancy. Simultaneously mothers are exposed to a wide range of other environmental chemicals. These chemicals may also harm the developing fetus, because almost all toxic compounds can go through human placenta. Toxicokinetic effects of ethanol on the transfer of other environmental compounds through human placenta have not been studied before. It is known that ethanol has lytic properties and increases the permeability and fluidity of cell membranes. We studied the effects of ethanol on the transfer of three different environmental toxins: nicotine, PhIP (2-amino-1-methyl-6-phenylimidazo(4,5-b)pyridine) and NDMA (N-nitrosodimethylamine) in placental perfusion. We tested in human breast cancer adenocarcinoma cell line MCF-7 whether ethanol affects ABCG2/BCRP, which is also the major transporter in human placenta. We found that the transfer of ethanol is comparable to that of antipyrine, which points to passive diffusion as the transfer mechanism. Unexpectedly, ethanol had no statistically significant effect on the transfer of the other studied compounds. Neither did ethanol inhibit the function of ABCG2/BCRP. These experiments represent only the effects of acute exposure to ethanol and chronic exposure remains to be studied. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Effects of cooling system parameters on heat transfer in PAFC stack. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Abdul-Aziz, Ali A.

1985-01-01

Analytical and experimental study for the effects of cooling system parameters on the heat transfer and temperature distribution in the electrode plates of a phosphoric acid fuel-cell has been conducted. An experimental set-up that simulates the operating conditions prevailing in a phosphoric-acid fuel-cell stack was designed and constructed. The set-up was then used to measure the overall heat transfer coefficient, the thermal contact resistance, and the electrode temperature distribution for two different cooling plate configurations. Two types of cooling plate configurations, serpentine and straight, were tested. Air, water, and oil were used as coolants. Measurements for the heat transfer coefficient and the thermal contact resistance were made for various flow rates ranging from 16 to 88 Kg/hr, and stack clamping pressure ranging from O to 3448 Kpa. The experimental results for the overall heat transfer coefficient were utilized to derive mathematical relations for the overall heat transfer coefficient as a function of stack clamping pressure and Reynolds number for the three coolants. The empirically derived formulas were incorporated in a previously developed computer program to predict electrodes temperature distribution and the performance of the stack cooling system. The results obtained were then compared with those available in the literature. The comparison showed maximum deviation of +/- 11%.

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

NASA Technical Reports Server (NTRS)

Frady, Gregory P.; Duvall, Lowery D.; Fulcher, Clay W. G.; Laverde, Bruce T.; Hunt, Ronald A.

2011-01-01

A rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for a curved orthogrid panel typical of launch vehicle skin structures. Several test article configurations were produced by adding component equipment of differing weights to the flight-like vehicle panel. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was employed to describe the assumed correlation of phased input sound pressures across the energized panel. This application demonstrates the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software modules developed for the RPTF method can be easily adapted for quick replacement of the diffuse acoustic field with other pressure field models; for example a turbulent boundary layer (TBL) model suitable for vehicle ascent. Wind tunnel tests have been proposed to anchor the predictions and provide new insight into modeling approaches for this type of environment. Finally, component vibration environments for design were developed from the measured and predicted responses and compared with those derived from traditional techniques such as Barrett scaling methods for unloaded and component-loaded panels.

Nerve Transfers to Restore Shoulder Function.

PubMed

Leechavengvongs, Somsak; Malungpaishorpe, Kanchai; Uerpairojkit, Chairoj; Ng, Chye Yew; Witoonchart, Kiat

2016-05-01

The restoration of shoulder function after brachial plexus injury represents a significant challenge facing the peripheral nerve surgeons. This is owing to a combination of the complex biomechanics of the shoulder girdle, the multitude of muscles and nerves that could be potentially injured, and a limited number of donor options. In general, nerve transfer is favored over tendon transfer, because the biomechanics of the musculotendinous units are not altered. This article summarizes the surgical techniques and clinical results of nerve transfers for restoration of shoulder function. Copyright © 2016 Elsevier Inc. All rights reserved.

Outcome following phrenic nerve transfer to musculocutaneous nerve in patients with traumatic brachial palsy: a qualitative systematic review.

PubMed

de Mendonça Cardoso, Marcio; Gepp, Ricardo; Correa, José Fernando Guedes

2016-09-01

The phrenic nerve can be transferred to the musculocutaneous nerve in patients with traumatic brachial plexus palsy in order to recover biceps strength, but the results are controversial. There is also a concern about pulmonary function after phrenic nerve transection. In this paper, we performed a qualitative systematic review, evaluating outcomes after this procedure. A systematic review of published studies was undertaken in accordance with the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) statement. Data were extracted from the selected papers and related to: publication, study design, outcome (biceps strength in accordance with BMRC and pulmonary function) and population. Study quality was assessed using the "strengthening the reporting of observational studies in epidemiology" (STROBE) standard or the CONSORT checklist, depending on the study design. Seven studies were selected for this systematic review after applying inclusion and exclusion criteria. One hundred twenty-four patients completed follow-up, and most of them were graded M3 or M4 (70.1 %) for biceps strength at the final evaluation. Pulmonary function was analyzed in five studies. It was not possible to perform a statistical comparison between studies because the authors used different parameters for evaluation. Most of the patients exhibited a decrease in pulmonary function tests immediately after surgery, with recovery in the following months. Study quality was determined using STROBE in six articles, and the global score varied from 8 to 21. Phrenic nerve transfer to the musculocutaneous nerve can recover biceps strength ≥M3 (BMRC) in most patients with traumatic brachial plexus injury. Early postoperative findings revealed that the development of pulmonary symptoms is rare, but it cannot be concluded that the procedure is safe because there is no study evaluating pulmonary function in old age.

BIOLOGICALLY ENHANCED OXYGEN TRANSFER IN THE ACTIVATED SLUDGE PROCESS (JOURNAL)

EPA Science Inventory

Biologically enhanced oxgyen transfer has been a hypothesis to explain observed oxygen transfer rates in activated sludge systems that were well above that predicted from aerator clean-water testing. The enhanced oxygen transfer rates were based on tests using BOD bottle oxygen ...

Transfer of Learning.

ERIC Educational Resources Information Center

1999

This document contains four symposium papers on transfer of learning. In "Learning Transfer in a Social Service Agency: Test of an Expectancy Model of Motivation" (Reid A. Bates) structural equation modeling is used to test the validity of a valence-instrumentality-expectancy approach to motivation to transfer learning. "The…

Bidirectional Transfer between Metaphorical Related Domains in Implicit Learning of Form-Meaning Connections

PubMed Central

Yang, Zhiliang; Dienes, Zoltan

2013-01-01

People can implicitly learn a connection between linguistic forms and meanings, for example between specific determiners (e.g. this, that…) and the type of nouns to which they apply. Li et al (2013) recently found that transfer of form-meaning connections from a concrete domain (height) to an abstract domain (power) was achieved in a metaphor-consistent way without awareness, showing that unconscious knowledge can be abstract and flexibly deployed. The current study aims to determine whether people transfer knowledge of form-meaning connections not only from a concrete domain to an abstract one, but also vice versa, consistent with metaphor representation being bi-directional. With a similar paradigm as used by Li et al, participants learnt form- meaning connections of different domains (concrete vs. abstract) and then were tested on two kinds of generalizations (same and different domain generalization). As predicted, transfer of form-meaning connections occurred bidirectionally when structural knowledge was unconscious. Moreover, the present study also revealed that more transfer occurred between metaphorically related domains when judgment knowledge was conscious (intuition) rather than unconscious (guess). Conscious and unconscious judgment knowledge may have different functional properties. PMID:23844159

Completion processing for data communications instructions

DOEpatents

Blocksome, Michael A.; Kumar, Sameer; Parker, Jeffrey J.

2014-06-03

Completion processing of data communications instructions in a distributed computing environment, including receiving, in an active messaging interface (`AMI`) data communications instructions, at least one instruction specifying a callback function; injecting into an injection FIFO buffer of a data communication adapter, an injection descriptor, each slot in the injection FIFO buffer having a corresponding slot in a pending callback list; listing in the pending callback list any callback function specified by an instruction, incrementing a pending callback counter for each listed callback function; transferring payload data as per each injection descriptor, incrementing a transfer counter upon completion of each transfer; determining from counter values whether the pending callback list presently includes callback functions whose data transfers have been completed; calling by the AMI any such callback functions from the pending callback list, decrementing the pending callback counter for each callback function called.

Dynamic Modeling and Testing of MSRR-1 for Use in Microgravity Environments Analysis

NASA Technical Reports Server (NTRS)

Gattis, Christy; LaVerde, Bruce; Howell, Mike; Phelps, Lisa H. (Technical Monitor)

2001-01-01

Delicate microgravity science is unlikely to succeed on the International Space Station if vibratory and transient disturbers corrupt the environment. An analytical approach to compute the on-orbit acceleration environment at science experiment locations within a standard payload rack resulting from these disturbers is presented. This approach has been grounded by correlation and comparison to test verified transfer functions. The method combines the results of finite element and statistical energy analysis using tested damping and modal characteristics to provide a reasonable approximation of the total root-mean-square (RMS) acceleration spectra at the interface to microgravity science experiment hardware.

Assessment of Laminar, Convective Aeroheating Prediction Uncertainties for Mars Entry Vehicles

NASA Technical Reports Server (NTRS)

Hollis, Brian R.; Prabhu, Dinesh K.

2011-01-01

An assessment of computational uncertainties is presented for numerical methods used by NASA to predict laminar, convective aeroheating environments for Mars entry vehicles. A survey was conducted of existing experimental heat-transfer and shock-shape data for high enthalpy, reacting-gas CO2 flows and five relevant test series were selected for comparison to predictions. Solutions were generated at the experimental test conditions using NASA state-of-the-art computational tools and compared to these data. The comparisons were evaluated to establish predictive uncertainties as a function of total enthalpy and to provide guidance for future experimental testing requirements to help lower these uncertainties.

Assessment of Laminar, Convective Aeroheating Prediction Uncertainties for Mars-Entry Vehicles

NASA Technical Reports Server (NTRS)

Hollis, Brian R.; Prabhu, Dinesh K.

2013-01-01

An assessment of computational uncertainties is presented for numerical methods used by NASA to predict laminar, convective aeroheating environments for Mars-entry vehicles. A survey was conducted of existing experimental heat transfer and shock-shape data for high-enthalpy reacting-gas CO2 flows, and five relevant test series were selected for comparison with predictions. Solutions were generated at the experimental test conditions using NASA state-of-the-art computational tools and compared with these data. The comparisons were evaluated to establish predictive uncertainties as a function of total enthalpy and to provide guidance for future experimental testing requirements to help lower these uncertainties.

Online games training aging brains: limited transfer to cognitive control functions

PubMed Central

van Muijden, Jesse; Band, Guido P. H.; Hommel, Bernhard

2011-01-01

The prevalence of age-related cognitive decline will increase due to graying of the global population. The goal of the present study was to test whether playing online cognitive training games can improve cognitive control (CC) in healthy older adults. Fifty-four older adults (age 60–77) played five different cognitive training games online for 30 min a day over a period of seven weeks (game group). Another group of 20 older adults (age 61–73) instead answered quiz questions about documentaries online (documentary group). Transfer was assessed by means of a cognitive test battery administered before and after the intervention. The test battery included measures of working memory updating, set shifting, response inhibition, attention, and inductive reasoning. Compared with the documentary group, the game group showed larger improvement of inhibition (Stop-Signal task) and inductive reasoning (Raven-SPM), whereas the documentary group showed more improvement in selective attention (UFoV-3). These effects qualify as transfer effects, because response inhibition, inductive reasoning and selective attention were not targeted by the interventions. However, because seven other indicators of CC did not show benefits of game training and some of those that did suffered from potential baseline differences, the study as a whole provides only modest support for the potential of videogame training to improve CC in healthy older adults. PMID:22912609

Gas Transfer in Cellularized Collagen-Membrane Gas Exchange Devices.

PubMed

Lo, Justin H; Bassett, Erik K; Penson, Elliot J N; Hoganson, David M; Vacanti, Joseph P

2015-08-01

Chronic lower respiratory disease is highly prevalent in the United States, and there remains a need for alternatives to lung transplant for patients who progress to end-stage lung disease. Portable or implantable gas oxygenators based on microfluidic technologies can address this need, provided they operate both efficiently and biocompatibly. Incorporating biomimetic materials into such devices can help replicate native gas exchange function and additionally support cellular components. In this work, we have developed microfluidic devices that enable blood gas exchange across ultra-thin collagen membranes (as thin as 2 μm). Endothelial, stromal, and parenchymal cells readily adhere to these membranes, and long-term culture with cellular components results in remodeling, reflected by reduced membrane thickness. Functionally, acellular collagen-membrane lung devices can mediate effective gas exchange up to ∼288 mL/min/m(2) of oxygen and ∼685 mL/min/m(2) of carbon dioxide, approaching the gas exchange efficiency noted in the native lung. Testing several configurations of lung devices to explore various physical parameters of the device design, we concluded that thinner membranes and longer gas exchange distances result in improved hemoglobin saturation and increases in pO2. However, in the design space tested, these effects are relatively small compared to the improvement in overall oxygen and carbon dioxide transfer by increasing the blood flow rate. Finally, devices cultured with endothelial and parenchymal cells achieved similar gas exchange rates compared with acellular devices. Biomimetic blood oxygenator design opens the possibility of creating portable or implantable microfluidic devices that achieve efficient gas transfer while also maintaining physiologic conditions.

Non-destructive testing of ceramic materials using mid-infrared ultrashort-pulse laser

NASA Astrophysics Data System (ADS)

Sun, S. C.; Qi, Hong; An, X. Y.; Ren, Y. T.; Qiao, Y. B.; Ruan, Liming M.

2018-04-01

The non-destructive testing (NDT) of ceramic materials using mid-infrared ultrashort-pulse laser is investigated in this study. The discrete ordinate method is applied to solve the transient radiative transfer equation in 2D semitransparent medium and the emerging radiative intensity on boundary serves as input for the inverse analysis. The sequential quadratic programming algorithm is employed as the inverse technique to optimize objective function, in which the gradient of objective function with respect to reconstruction parameters is calculated using the adjoint model. Two reticulated porous ceramics including partially stabilized zirconia and oxide-bonded silicon carbide are tested. The retrieval results show that the main characteristics of defects such as optical properties, geometric shapes and positions can be accurately reconstructed by the present model. The proposed technique is effective and robust in NDT of ceramics even with measurement errors.

Cysteine-Accelerated Methanogenic Propionate Degradation in Paddy Soil Enrichment.

PubMed

Zhuang, Li; Ma, Jinlian; Tang, Jia; Tang, Ziyang; Zhou, Shungui

2017-05-01

Propionate degradation is a critical step during the conversion of complex organic matter under methanogenic conditions, and it requires a syntrophic cooperation between propionate-oxidizing bacteria and methanogenic archaea. Increasing evidences suggest that interspecies electron transfer for syntrophic metabolism is not limited to the reducing equivalents of hydrogen and formate. This study tested the ability of an electron shuttle to mediate interspecies electron transfer in syntrophic methanogenesis. We found that cysteine supplementation (100, 400, and 800 μM) accelerated CH 4 production from propionate in paddy soil enrichments. Of the concentrations tested, 100 μM cysteine was the most effective at enhancing propionate degradation to CH 4 , and the rates of CH 4 production and propionate degradation were increased by 109 and 79%, respectively, compared with the cysteine-free control incubations. We eliminated the possibility that the stimulatory effect of cysteine on methanogenesis was attributable to the function of cysteine as a methanogenic substrate in the presence of propionate. The potential catalytic effect involved cysteine serving as an electron carrier to mediate interspecies electron transfer in syntrophic propionate oxidization. The redox potential of cystine/cysteine, which is dependent on the concentration, might be more suitable to facilitate interspecies electron transfer between syntrophic partners at a concentration of 100 μM. Pelotomaculum, obligately syntrophic, propionate-oxidizing bacteria, and hydrogenotrophic methanogens of the family Methanobacteriaceae are predominant in cysteine-mediated methanogenic propionate degradation. The stimulatory effect of cysteine on syntrophic methanogenesis offers remarkable potential for improving the performance of anaerobic digestion and conceptually broaden strategies for interspecies electron transfer in syntrophic metabolism.

Subjective Learning Discounts Test Type: Evidence from an Associative Learning and Transfer Task

PubMed Central

Touron, Dayna R.; Hertzog, Christopher; Speagle, James Z.

2011-01-01

We evaluated the extent to which memory test format and test transfer influence the dynamics of metacognitive judgments. Participants completed 2 study-test phases for paired-associates, with or without transferring test type, in one of four conditions: (1) recognition then recall, (2) recall then recognition, (3) recognition throughout, or (4) recall throughout. Global judgments were made pre-study, post-study, and post-test for each phase; judgments of learning (JOLs) following item study were also collected. Results suggest that metacognitive judgment accuracy varies substantially by memory test type. Whereas underconfidence in JOLs and global predictions increases with recall practice (Koriat’s underconfidence-with-practice effect), underconfidence decreases with recognition practice. Moreover, performance changes when transferring test type were not fully anticipated by pre-test judgments. PMID:20178957

Development of zwitterionic sulfobetaine block copolymer conjugation strategies for reduced platelet deposition in respiratory assist devices.

PubMed

Malkin, Alexander D; Ye, Sang-Ho; Lee, Evan J; Yang, Xiguang; Zhu, Yang; Gamble, Lara J; Federspiel, William J; Wagner, William R

2018-02-09

Respiratory assist devices, that utilize ∼2 m 2 of hollow fiber membranes (HFMs) to achieve desired gas transfer rates, have been limited in their adoption due to such blood biocompatibility limitations. This study reports two techniques for the functionalization and subsequent conjugation of zwitterionic sulfobetaine (SB) block copolymers to polymethylpentene (PMP) HFM surfaces with the intention of reducing thrombus formation in respiratory assist devices. Amine or hydroxyl functionalization of PMP HFMs (PMP-A or PMP-H) was accomplished using plasma-enhanced chemical vapor deposition. The generated functional groups were conjugated to low molecular weight SB block copolymers with N-hydroxysuccinimide ester or siloxane groups (SBNHS or SBNHSi) that were synthesized using reversible addition fragmentation chain transfer polymerization. The modified HFMs (PMP-A-SBNHS or PMP-H-SBNHSi) showed 80-95% reduction in platelet deposition from whole ovine blood, stability under the fluid shear of anticipated operating conditions, and uninhibited gas exchange performance relative to non-modified HFMs (PMP-C). Additionally, the functionalization and SBNHSi conjugation technique was shown to reduce platelet deposition on polycarbonate and poly(vinyl chloride), two other materials commonly found in extracorporeal circuits. The observed thromboresistance and stability of the SB modified surfaces, without degradation of HFM gas transfer performance, indicate that this approach is promising for longer term pre-clinical testing in respiratory assist devices and may ultimately allow for the reduction of anticoagulation levels in patients being supported for extended periods. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc.

Interactive dual-volume rendering visualization with real-time fusion and transfer function enhancement

NASA Astrophysics Data System (ADS)

Macready, Hugh; Kim, Jinman; Feng, David; Cai, Weidong

2006-03-01

Dual-modality imaging scanners combining functional PET and anatomical CT constitute a challenge in volumetric visualization that can be limited by the high computational demand and expense. This study aims at providing physicians with multi-dimensional visualization tools, in order to navigate and manipulate the data running on a consumer PC. We have maximized the utilization of pixel-shader architecture of the low-cost graphic hardware and the texture-based volume rendering to provide visualization tools with high degree of interactivity. All the software was developed using OpenGL and Silicon Graphics Inc. Volumizer, tested on a Pentium mobile CPU on a PC notebook with 64M graphic memory. We render the individual modalities separately, and performing real-time per-voxel fusion. We designed a novel "alpha-spike" transfer function to interactively identify structure of interest from volume rendering of PET/CT. This works by assigning a non-linear opacity to the voxels, thus, allowing the physician to selectively eliminate or reveal information from the PET/CT volumes. As the PET and CT are rendered independently, manipulations can be applied to individual volumes, for instance, the application of transfer function to CT to reveal the lung boundary while adjusting the fusion ration between the CT and PET to enhance the contrast of a tumour region, with the resultant manipulated data sets fused together in real-time as the adjustments are made. In addition to conventional navigation and manipulation tools, such as scaling, LUT, volume slicing, and others, our strategy permits efficient visualization of PET/CT volume rendering which can potentially aid in interpretation and diagnosis.

Heat transfer measurements from a NACA 0012 airfoil in flight and in the NASA Lewis icing research tunnel. M.S. Thesis Final Report

NASA Technical Reports Server (NTRS)

Poinsatte, Philip E.

1990-01-01

Local heat transfer coefficients from a smooth and roughened NACA 0012 airfoil were measured using a steady state heat flux method. Heat transfer measurements on the specially constructed 0.533 meter chord airfoil were made both in flight on the NASA Lewis Twin Otter Research Aircraft and in the NASA Lewis Icing Research Tunnel (IRT). Roughness was obtained by the attachment of small, 2 mm diameter, hemispheres of uniform size to the airfoil surface in four distinct patterns. The flight data was taken for the smooth and roughened airfoil at various Reynolds numbers based on chord in the range of 1.24x10(exp 6) to 2.50x10(exp 6) and at various angles of attack up to 4 degrees. During these flight tests the free stream velocity turbulence intensity was found to be very low (less than 0.1 percent). The wind tunnel data was taken in the Reynolds number range of 1.20x10(exp 6) to 4.52x10(exp 6) and at angles of attack from -4 degrees to +8 degrees. The turbulence intensity in the IRT was 0.5 to 0.7 percent with the cloud making spray off. Results for both the flight and tunnel tests are presented as Frossling number based on chord versus position on the airfoil surface for various roughnesses and angle of attack. A table of power law curve fits of Nusselt number as a function of Reynolds number is also provided. The higher level of turbulence in the IRT versus flight had little effect on heat transfer for the lower Reynolds numbers but caused a moderate increase in heat transfer at the higher Reynolds numbers. Turning on the cloud making spray air in the IRT did not alter the heat transfer. Roughness generally increased the heat transfer by locally disturbing the boundary layer flow. Finally, the present data was not only compared with previous airfoil data where applicable, but also with leading edge cylinder and flat plate heat transfer values which are often used to estimate airfoil heat transfer in computer codes.

Förster-Induced Energy Transfer in Functionalized Graphene

PubMed Central

2014-01-01

Carbon nanostructures are ideal substrates for functionalization with molecules since they consist of a single atomic layer giving rise to an extraordinary sensitivity to changes in their surrounding. The functionalization opens a new research field of hybrid nanostructures with tailored properties. Here, we present a microscopic view on the substrate–molecule interaction in the exemplary hybrid material consisting of graphene functionalized with perylene molecules. First experiments on similar systems have been recently realized illustrating an extremely efficient transfer of excitation energy from adsorbed molecules to the carbon substrate, a process with a large application potential for high-efficiency photovoltaic devices and biomedical imaging and sensing. So far, there has been no microscopically founded explanation for the observed energy transfer. Based on first-principle calculations, we have explicitly investigated the different transfer mechanisms revealing the crucial importance of Förster coupling. Due to the efficient Coulomb interaction in graphene, we obtain strong Förster rates in the range of 1/fs. We investigate its dependence on the substrate–molecule distance R and describe the impact of the momentum transfer q for an efficient energy transfer. Furthermore, we find that the Dexter transfer mechanism is negligibly small due to the vanishing overlap between the involved strongly localized orbital functions. The gained insights are applicable to a variety of carbon-based hybrid nanostructures. PMID:24808936

Occupational Rhinoconjunctivitis due to Maize in a Snack Processor: A Cross-Reactivity Study Between Lipid Transfer Proteins From Different Cereals and Peach.

PubMed

Guillen, Daiana; Barranco, Pilar; Palacín, Arantxa; Quirce, Santiago

2014-09-01

We report the case of a snack processor who developed occupational rhinoconjunctivitis due to maize brand exposure during the extrusion process, and who experienced abdominal pain upon drinking beer. The allergens implicated and the cross-reactivity between non-specific lipid transfer proteins (LTPs) from different cereals and peach were investigated. Skin prick tests and specific IgE to cereal flours, pulmonary functions tests and specific conjunctival and inhalation challenges to maize extract were performed. In vitro studies included IgE immunoblotting and ELISA inhibition assays. Skin prick tests with maize flour, maize brand and wheat flour extracts were positive, whereas serum specific IgE was positive only to maize flour. Specific inhalation challenge (SIC) to maize flour did not elicit an asthmatic reaction; however, conjunctival challenge test with the same extract was positive. Patient's serum recognized IgE-binding bands in the maize and beer extracts corresponding to LTPs. In the ELISA inhibition assays, a significant degree of allergenic cross-reactivity was found between maize and beer LTPs, whereas no cross-reactivity was observed between maize LTP and wheat and peach LTPs.

Hydrophobic and optical characteristics of graphene and graphene oxide films transferred onto functionalized silica particles deposited glass surface

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Ibrahim, A.; Ali, H.; Khaled, M.; Laoui, T.

2018-06-01

Hydrophobic and optical transmittance characteristics of the functionalized silica particles on the glass surface prior and after transfer of graphene and graphene oxide films on the surface are examined. Nano-size silica particles are synthesized and functionalized via chemical grafting and deposited onto a glass surface. Graphene film, grown on copper substrate, was transferred onto the functionalized silica particles surface through direct fishing method. Graphene oxide layer was deposited onto the functionalized silica particles surface via spin coating technique. Morphological, hydrophobic, and optical characteristics of the functionalized silica particles deposited surface prior and after graphene and graphene oxide films transfer are examined using the analytical tools. It is found that the functionalized silica particles are agglomerated at the surface forming packed structures with few micro/nano size pores. This arrangement gives rise to water droplet contact angle and contact angle hysteresis in the order of 163° and 2°, respectively, and remains almost uniform over the entire surface. Transferring graphene and depositing graphene oxide films over the functionalized silica particles surface lowers the water droplet contact angle slightly (157-160°) and increases the contact angle hysteresis (4°). The addition of the graphene and graphene oxide films onto the surface of the deposited functionalized silica particles improves the optical transmittance.

CD8+ T Cells Cause Disability and Axon Loss in a Mouse Model of Multiple Sclerosis

PubMed Central

Schmalstieg, William F.; Sauer, Brian M.; Wang, Huan; German, Christopher L.; Windebank, Anthony J.; Rodriguez, Moses; Howe, Charles L.

2010-01-01

Background The objective of this study was to test the hypothesis that CD8+ T cells directly mediate motor disability and axon injury in the demyelinated central nervous system. We have previously observed that genetic deletion of the CD8+ T cell effector molecule perforin leads to preservation of motor function and preservation of spinal axons in chronically demyelinated mice. Methodology/Principal Findings To determine if CD8+ T cells are necessary and sufficient to directly injure demyelinated axons, we adoptively transferred purified perforin-competent CD8+ spinal cord-infiltrating T cells into profoundly demyelinated but functionally preserved perforin-deficient host mice. Transfer of CD8+ spinal cord-infiltrating T cells rapidly and irreversibly impaired motor function, disrupted spinal cord motor conduction, and reduced the number of medium- and large-caliber spinal axons. Likewise, immunodepletion of CD8+ T cells from chronically demyelinated wildtype mice preserved motor function and limited axon loss without altering other disease parameters. Conclusions/Significance In multiple sclerosis patients, CD8+ T cells outnumber CD4+ T cells in active lesions and the number of CD8+ T cells correlates with the extent of ongoing axon injury and functional disability. Our findings suggest that CD8+ T cells may directly injure demyelinated axons and are therefore a viable therapeutic target to protect axons and motor function in patients with multiple sclerosis. PMID:20814579

Hydrogen bonding in malonaldehyde: a density functional and reparametrized semiempirical approach

NASA Astrophysics Data System (ADS)

Kovačević, Goran; Hrenar, Tomica; Došlić, Nadja

2003-08-01

Intramolecular proton transfer in malonaldehyde (MA) has been investigated by density functional theory (DFT). The DFT results were used for the construction of a high quality semiempirical potential energy surface with a reparametrized PM3 Hamiltonian. A two-step reparameterization procedure is proposed in which (i) the PM3-MAIS core-core functions for the O-H and H-H interactions were used and a new functional form for the O-O correction function was proposed and (ii) a set of specific reaction parameters (SRP) has been obtained via genetic algorithm optimization. The quality of the reparametrized semiempirical potential energy surfaces was tested by calculating the tunneling splitting of vibrational levels and the anharmonic vibrational frequencies of the system. The applicability to multi-dimensional dynamics in large molecular systems is discussed.

Comparison of Regression Analysis and Transfer Function in Estimating the Parameters of Central Pulse Waves from Brachial Pulse Wave.

PubMed

Chai, Rui; Xu, Li-Sheng; Yao, Yang; Hao, Li-Ling; Qi, Lin

2017-01-01

This study analyzed ascending branch slope (A_slope), dicrotic notch height (Hn), diastolic area (Ad) and systolic area (As) diastolic blood pressure (DBP), systolic blood pressure (SBP), pulse pressure (PP), subendocardial viability ratio (SEVR), waveform parameter (k), stroke volume (SV), cardiac output (CO), and peripheral resistance (RS) of central pulse wave invasively and non-invasively measured. Invasively measured parameters were compared with parameters measured from brachial pulse waves by regression model and transfer function model. Accuracy of parameters estimated by regression and transfer function model, was compared too. Findings showed that k value, central pulse wave and brachial pulse wave parameters invasively measured, correlated positively. Regression model parameters including A_slope, DBP, SEVR, and transfer function model parameters had good consistency with parameters invasively measured. They had same effect of consistency. SBP, PP, SV, and CO could be calculated through the regression model, but their accuracies were worse than that of transfer function model.

Analyzing Community College Student Transfer Rates.

ERIC Educational Resources Information Center

Cohen, Arthur M.

The community college mission includes such diverse goals as preparing students for job entry, teaching literacy, and satisfying students' personal interests. Measuring the colleges' transfer rates by no means tacitly elevates the transfer function above these other functions; it merely helps institutions estimate the effects of interventions on…

Laser induced forward transfer of graphene

NASA Astrophysics Data System (ADS)

Smits, Edsger C. P.; Walter, Arnaud; de Leeuw, Dago M.; Asadi, Kamal

2017-10-01

Transfer of graphene and other two-dimensional materials is still a technical challenge. The 2D-materials are typically patterned after transfer, which leads to a major loss of material. Here, we present laser induced forward transfer of chemical vapor deposition grown graphene layers with well-defined shapes and geometries. The transfer is based on photo-decomposition of a triazene-based transfer layer that produces N2 gas, which propels a graphene layer from the donor to the acceptor substrate. The functionality of the graphene-metal junction was verified by realizing functional bottom contact bottom gate field-effect transistors.

Comparison of two different rehabilitation programmes for thrust plate prosthesis: a randomized controlled study.

PubMed

Unver, Bayram; Karatosun, Vasfi; Gunal, Izge; Angin, Salih

2004-02-01

Weight bearing after total hip arthroplasty is postponed in order to prevent early loosening, but this negatively affects the rehabilitation programme. For the force transfer characteristics of thrust plate prosthesis (TPP), a new type of hip prosthesis used without cement is similar to the normal hip. We evaluated the possibilities of early weight bearing after TPP by comparing early partial with early full weight bearing. Randomized controlled study. Department of orthopaedics and traumatology in a university hospital. Sixty hips of 51 patients who underwent total hip arthroplasty with TPP were randomly assigned into two groups. Both groups received accelerated rehabilitation programmes: group 1 with early partial weight bearing and group 2 with early full weight bearing. Patients were evaluated by a blind observer preoperatively, at three months after surgery by clinical (measurement of range of hip motion (universal goniometry), muscle strength (Manual Muscle Test), functional test (6-minute walk test), hip function (Harris Hip Scoring System)) and radiographical parameters and one year after surgery by clinical (Harris Hip Scoring System) and radiographical parameters. Group 2 performed transfer activities earlier, had more walking distance at the time of discharge and shorter hospital stay than group 1. At three months, Harris Hip Score, muscle strength, 6-minute walk test, and duration of crutch use were significantly (p < 0.05) in favour of group 2. None of the patients in either group showed signs of loosening one year after the operation. These results suggest that patients with TPP can tolerate an accelerated rehabilitation programme with early weight bearing and will gain the goals of rehabilitation earlier.

Coordinating Upper and Lower Body During FES-Assisted Transfers in Persons With Spinal Cord Injury in Order to Reduce Arm Support.

PubMed

Jovic, Jovana; Azevedo Coste, Christine; Fraisse, Philippe; Henkous, Sonia; Fattal, Charles

2015-12-01

The goal of this study is to minimize arm forces applied during sit-to-stand (STS) transfers in persons with spinal cord injury (SCI) by using functional electrical stimulation (FES) applied to lower limbs muscles. A new FES system has been used to automatically trigger muscle stimulation of the lower limbs, at the desired moment in regards to trunk motion. The objective was to decrease arm participation during STS motion of a person with complete paraplegia and low-level tetraplegia. Six participants with chronic SCI participated in the study. Participants with SCI were recruited to complete STS movement using a new system for FES-assisted STS transfer. All participants attended one muscle mapping session to test their muscles condition, two training sessions to become familiarized with the experimental setup, and two measurement sessions using the proposed system for FES-assisted STS movement. The applied arm forces during STS movement were recorded and analyzed for different stimulation onset values with respect to the maximal trunk acceleration signal using one-way ANOVA statistical test. Post-hoc analysis was performed using Tukey's method. The results of this study showed that the moment of the stimulation onset has an influence on the arm forces applied during the STS motion. The lowest values of arm forces were obtained for STS movements where the electrical stimulation was triggered before and around the time corresponding to the maximal value of the trunk acceleration signal. Lowest arm forces values were obtained for STS motions that were similar to those of healthy persons in terms of trunk movements and beginning of lower limb movements in regards to maximal trunk acceleration signal. The FES system was able to mimic the rising motion of a healthy individual by triggering the FES at the appropriate moment. This method could prove useful for pivot transfer, therapeutic or functional verticalization. © 2015 International Neuromodulation Society.

Children and adolescents' performance on a medium-length/nonsemantic word-list test.

PubMed

Flores-Lázaro, Julio César; Salgado Soruco, María Alejandra; Stepanov, Igor I

2017-01-01

Word-list learning tasks are among the most important and frequently used tests for declarative memory evaluation. For example, the California Verbal Learning Test-Children's Version (CVLT-C) and Rey Auditory Verbal Learning Test provide important information about different cognitive-neuropsychological processes. However, the impact of test length (i.e., number of words) and semantic organization (i.e., type of words) on children's and adolescents' memory performance remains to be clarified, especially during this developmental stage. To explore whether a medium-length non-semantically organized test can produce the typical curvilinear performance that semantically organized tests produce, reflecting executive control, we studied and compared the cognitive performance of normal children and adolescents by utilizing mathematical modeling. The model is based on the first-order system transfer function and has been successfully applied to learning curves for the CVLT-C (15 words, semantically organized paradigm). Results indicate that learning nine semantically unrelated words produces typical curvilinear (executive function) performance in children and younger adolescents and that performance could be effectively analyzed with the mathematical model. This indicates that the exponential increase (curvilinear performance) of correctly learned words does not solely depend on semantic and/or length features. This type of test controls semantic and length effects and may represent complementary tools for executive function evaluation in clinical populations in which semantic and/or length processing are affected.

Surfactant effects on alpha factors in full-scale wastewater aeration systems.

PubMed

Rosso, D; Larson, L E; Stenstrom, M K

2006-01-01

Aeration is an essential process in the majority of wastewater treatment processes, and accounts for the largest fraction of plant energy costs. Aeration systems can achieve wastewater oxygenation by shearing the surface (surface aerators) or releasing bubbles at the bottom of the tank (coarse- or fine-bubble aerators). Surfactants accumulate on gas-liquid interfaces and reduce mass transfer rates. This reduction in general is larger for fine-bubble aerators. This study was conducted to evaluate mass transfer effects on the characterization and specification of aeration systems in clean and process water conditions. Tests at different interfacial turbulence regimes were analysed, showing higher gas transfer depression for lower turbulence regimes. Higher turbulence regimes can offset contamination effects, at the expense of operating efficiency. This phenomenon is characteristic of surface aerators and coarse bubble diffusers and is here discussed. The results explain the variability of alpha factors measured at small scale, due to uncontrolled energy density. Results are also reported in dimensionless empirical correlations that describe mass transfer as a function of physiochemical and geometrical characteristics of the aeration process.

First FAMU observation of muon transfer from μp atoms to higher-Z elements

NASA Astrophysics Data System (ADS)

Mocchiutti, E.; Bonvicini, V.; Carbone, R.; Danailov, M.; Furlanetto, E.; Gadedjisso-Tossou, K. S.; Guffanti, D.; Pizzolotto, C.; Rachevski, A.; Stoychev, L.; Vallazza, E.; Zampa, G.; Niemela, J.; Ishida, K.; Adamczak, A.; Baccolo, G.; Benocci, R.; Bertoni, R.; Bonesini, M.; Chignoli, F.; Clemenza, M.; Curioni, A.; Maggi, V.; Mazza, R.; Moretti, M.; Nastasi, M.; Previtali, E.; Bakalov, D.; Danev, P.; Stoilov, M.; Baldazzi, G.; Campana, G.; D'Antone, I.; Furini, M.; Fuschino, F.; Labanti, C.; Margotti, A.; Meneghini, S.; Morgante, G.; Rignanese, L. P.; Rossi, P. L.; Zuffa, M.; Cervi, T.; De Bari, A.; Menegolli, A.; De Vecchi, C.; Nardò, R.; Rossella, M.; Tomaselli, A.; Colace, L.; De Vincenzi, M.; Iaciofano, A.; Somma, F.; Tortora, L.; Ramponi, R.; Vacchi, A.

2018-02-01

The FAMU experiment aims to accurately measure the hyperfine splitting of the ground state of the muonic hydrogen atom. A measurement of the transfer rate of muons from hydrogen to heavier gases is necessary for this purpose. In June 2014, within a preliminary experiment, a pressurized gas-target was exposed to the pulsed low-energy muon beam at the RIKEN RAL muon facility (Rutherford Appleton Laboratory, U.K.). The main goal of the test was the characterization of both the noise induced by the pulsed beam and the X-ray detectors. The apparatus, to some extent rudimental, has served admirably to this task. Technical results have been published that prove the validity of the choices made and pave the way for the next steps. This paper presents the results of physical relevance of measurements of the muon transfer rate to carbon dioxide, oxygen, and argon from non-thermalized excited μp atoms. The analysis methodology and the approach to the systematics errors are useful for the subsequent study of the transfer rate as function of the kinetic energy of the μp currently under way.

Synthesis and characterization of Nd3+: Yb3+ co-doped near infrared sensitive fluorapatite nanoparticles as a bioimaging probe

NASA Astrophysics Data System (ADS)

Karthi, S.; Kumar, G. A.; Sardar, D. K.; Santhosh, C.; Girija, E. K.

2018-03-01

Trivalent Nd and Yb co-doped rod shaped hexagonal phase fluorapatite (FAP) nanoparticles of length and width about 32 and 13 nm, respectively were prepared by hydrothermal method and investigated the ability for 980 nm emission via Nd3+ → Yb3+ energy transfer with the objective of utilizing them in biomedical imaging. Nd3+ → Yb3+ energy transfer in FAP was studied as a function of both Nd3+ and Yb3+ concentrations and found that when Yb3+ concentration was 10 mol% the FAP phase has partially turned in to YbPO4 phase. The Yb3+ emission intensity at 980 nm significantly increased up to 5 mol% Yb3+ doping and then reduced drastically for further increase in its concentration. Nd3+ →Yb3+ energy transfer rates were evaluated from the decay curves and found that a transfer rate of 71% for 2 mol% Nd3+ co-doped with 5 mol% Yb3+. The cytocompatibility test with fibroblast like cells using MTT assay revealed that the nanoparticles are compatible with the cells.

How to precisely measure the volume velocity transfer function of physical vocal tract models by external excitation

PubMed Central

Mainka, Alexander; Kürbis, Steffen; Birkholz, Peter

2018-01-01

Recently, 3D printing has been increasingly used to create physical models of the vocal tract with geometries obtained from magnetic resonance imaging. These printed models allow measuring the vocal tract transfer function, which is not reliably possible in vivo for the vocal tract of living humans. The transfer functions enable the detailed examination of the acoustic effects of specific articulatory strategies in speaking and singing, and the validation of acoustic plane-wave models for realistic vocal tract geometries in articulatory speech synthesis. To measure the acoustic transfer function of 3D-printed models, two techniques have been described: (1) excitation of the models with a broadband sound source at the glottis and measurement of the sound pressure radiated from the lips, and (2) excitation of the models with an external source in front of the lips and measurement of the sound pressure inside the models at the glottal end. The former method is more frequently used and more intuitive due to its similarity to speech production. However, the latter method avoids the intricate problem of constructing a suitable broadband glottal source and is therefore more effective. It has been shown to yield a transfer function similar, but not exactly equal to the volume velocity transfer function between the glottis and the lips, which is usually used to characterize vocal tract acoustics. Here, we revisit this method and show both, theoretically and experimentally, how it can be extended to yield the precise volume velocity transfer function of the vocal tract. PMID:29543829

Completion processing for data communications instructions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blocksome, Michael A; Kumar, Sameer; Parker, Jeffrey J

Completion processing of data communications instructions in a distributed computing environment, including receiving, in an active messaging interface (`AMI`) data communications instructions, at least one instruction specifying a callback function; injecting into an injection FIFO buffer of a data communication adapter, an injection descriptor, each slot in the injection FIFO buffer having a corresponding slot in a pending callback list; listing in the pending callback list any callback function specified by an instruction, incrementing a pending callback counter for each listed callback function; transferring payload data as per each injection descriptor, incrementing a transfer counter upon completion of each transfer;more » determining from counter values whether the pending callback list presently includes callback functions whose data transfers have been completed; calling by the AMI any such callback functions from the pending callback list, decrementing the pending callback counter for each callback function called.« less

Parametric dependence of ocean wave-radar modulation transfer functions

NASA Technical Reports Server (NTRS)

Plant, W. J.; Keller, W. C.; Cross, A.

1983-01-01

Microwave techniques at X and L band were used to determine the dependence of ocean-wave radar modulation transfer functions (MTFs) on various environmental and radar parameters during the Marine Remote Sensing experiment of 1979 (MARSEN 79). These MIF are presented, as are coherence functions between the AM and FM parts of the backscattered microwave signal. It is shown that they both depend on several of these parameters. Besides confirming many of the properties of transfer functions reported by previous authors, indications are found that MTFs decrease with increasing angle between wave propagation and antenna-look directions but are essentially independent of small changes in air-sea temperature difference. However, coherence functions are much smaller when the antennas are pointed perpendicular to long waves. It is found that X band transfer functions measured with horizontally polarized microwave radiation have larger magnitudes than those obtained by using vertical polarization.

Transfer effects of errorless Goal Management Training on cognitive function and quality of life in brain-injured persons.

PubMed

Bertens, Dirk; Kessels, Roy P C; Boelen, Danielle H E; Fasotti, Luciano

2016-01-01

Previous findings had shown that the addition of errorless learning to traditional Goal Management Training (GMT) resulted in superior results when training everyday tasks in persons with executive deficits after brain injury. To investigate the additional effects of an errorless GMT on cognitive function and quality of life after acquired brain injury. This is a supplementary analysis of findings from an RCT in which 67 patients with executive impairments after acquired brain injury were randomly allocated to an experimental errorless GMT (n = 33) or conventional GMT (n = 34) to train two individually chosen everyday tasks. Objective cognitive function using neuropsychological tests, subjective cognitive complaints and quality of life using questionnaires were assessed before and after training. No significant interaction effects between these three types of outcome measures and the two forms of GMT were found. Irrespective of treatment, performance on two executive tests (Modified Six Elements Test; p = 0.006, Zoo Map test; p = 0.001) improved and daily executive function problems as reported by the participants (EFI; p = 0.001) and proxies (DEX; p = 0.01) diminished. Besides the previously found superiority of errorless GMT when training everyday tasks, additional improvements in cognition and quality of life did not differ between the two treatments.

Effect on child cognitive function of increasing household expenditure in Indonesia: application of a marginal structural model and simulation of a cash transfer programme.

PubMed

Maika, Amelia; Mittinty, Murthy N; Brinkman, Sally; Lynch, John

2015-02-01

Parental investments in children are an important determinant of human capability formation. We investigated the causal effect of household expenditure on Indonesian children's cognitive function between 2000 and 2007. We also investigated the effect of change in mean cognitive function from a simulation of a hypothetical cash transfer intervention. A longitudinal analysis using data from the Indonesian Family Life Survey (IFLS) was conducted including 6136 children aged 7 to 14 years in 2000 and still alive in 2007. We used the inverse probability of treatment weighting of a marginal structural model to estimate the causal effect of household expenditure on children's cognitive function. Cumulative household expenditure was positively associated with cognitive function z-score. From the marginal structural model, a 74534 rupiah/month (about US$9) increase in household expenditure resulted in a 0.03 increase in cognitive function z-score [β=0.32, 95% confidence interval (CI) 0.30-0.35] Based on our simulations, among children in the poorest households in 2000 an additional ≈ US$6-10 of cash transfer resulted in a 0.01 unit increase in cognitive function z-score, equivalent to about 6% increase from the mean z-score prior to cash transfer. In contrast, children in the poorest household in 2007 did not benefit from an additional ≈ US$10 cash transfer. We found no overall effect of cash transfers at the total population level. Greater household expenditure had a small causal effect on children's cognitive function. Although cash transfer interventions had a positive effect for poor children, this effect was quite small. Multi-faceted interventions that combine nutrition, cash transfer, improved living conditions and women's education are required to benefit children's cognitive development in Indonesia. © The Author 2015; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association.

Explicit construction of quadratic Lyapunov functions for the small gain, positivity, circle, and Popov theorems and their application to robust stability

NASA Technical Reports Server (NTRS)

Haddad, Wassim M.; Bernstein, Dennis S.

1991-01-01

Lyapunov function proofs of sufficient conditions for asymptotic stability are given for feedback interconnections of bounded real and positive real transfer functions. Two cases are considered: (1) a proper bounded real (resp., positive real) transfer function with a bounded real (resp., positive real) time-varying memoryless nonlinearity; and (2) two strictly proper bounded real (resp., positive real) transfer functions. A similar treatment is given for the circle and Popov theorems. Application of these results to robust stability with time-varying bounded real, positive real, and sector-bounded uncertainty is discussed.

Water table tests of proposed heat transfer tunnels for small turbine vanes

NASA Technical Reports Server (NTRS)

Meitner, P. L.

1974-01-01

Water-table flow tests were conducted for proposed heat-transfer tunnels which were designed to provide uniform flow into their respective test sections of a single core engine turbine vane and a full annular ring of helicopter turbine vanes. Water-table tests were also performed for the single-vane test section of the core engine tunnel. The flow in the heat-transfer tunnels was shown to be acceptable.

Resolution of Transverse Electron Beam Measurements using Optical Transition Radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ischebeck, Rasmus; Decker, Franz-Josef; Hogan, Mark

2005-06-22

In the plasma wakefield acceleration experiment E-167, optical transition radiation is used to measure the transverse profile of the electron bunches before and after the plasma acceleration. The distribution of the electric field from a single electron does not give a point-like distribution on the detector, but has a certain extension. Additionally, the resolution of the imaging system is affected by aberrations. The transverse profile of the bunch is thus convolved with a point spread function (PSF). Algorithms that deconvolve the image can help to improve the resolution. Imaged test patterns are used to determine the modulation transfer function ofmore » the lens. From this, the PSF can be reconstructed. The Lucy-Richardson algorithm is used to deconvolute this PSF from test images.« less

Assessment of inlet efficiency through a 3D simulation: numerical and experimental comparison.

PubMed

Gómez, Manuel; Recasens, Joan; Russo, Beniamino; Martínez-Gomariz, Eduardo

2016-10-01

Inlet efficiency is a requirement for characterizing the flow transfers between surface and sewer flow during rain events. The dual drainage approach is based on the joint analysis of both upper and lower drainage levels, and the flow transfer is one of the relevant elements to define properly this joint behaviour. This paper presents the results of an experimental and numerical investigation about the inlet efficiency definition. A full scale (1:1) test platform located in the Technical University of Catalonia (UPC) reproduces both the runoff process in streets and the water entering the inlet. Data from tests performed on this platform allow the inlet efficiency to be estimated as a function of significant hydraulic and geometrical parameters. A reproduction of these tests through a numerical three-dimensional code (Flow-3D) has been carried out simulating this type of flow by solving the RANS equations. The aim of the work was to reproduce the hydraulic performance of a previously tested grated inlet under several flow and geometric conditions using Flow-3D as a virtual laboratory. This will allow inlet efficiencies to be obtained without previous experimental tests. Moreover, the 3D model allows a better understanding of the hydraulics of the flow interception and the flow patterns approaching the inlet.

Bipolar Latissimus Dorsi Transfer for Restoration of Pectoralis Major Function in Poland Syndrome.

PubMed

Buchanan, Patrick; Leyngold, Mark; Mast, Bruce A

2016-01-01

Poland syndrome typically presents as a unilateral congenital complete or partial absence of the pectoralis major muscle, variably with other associated anomalies. Reconstruction of the defect typically concentrates on aesthetic restoration with functional outcomes being unsuccessful or limited. We present an innovative means of true muscle transfer that provided functional benefit to increase upper extremity strength. A 16-year-old adolescent boy with Poland syndrome manifesting as left pectoralis major muscle agenesis wished to undergo functional reconstruction. He wanted to play on his high school football team, but could not meet the minimum weightlifting requirements. An ipsilateral latissimus dorsi muscle bipolar functional transfer was done with bone-anchored inset into the sternum and humerus so that muscle flexion would replace the absent pectoralis major. A progressive weight training program was then instituted postoperatively. At 9 months, a significant increase in left upper extremity strength was confirmed. The patient ultimately was able to surpass the weightlifting requirements for his high school football team, and joined the team. Our highlighted procedure restored functional outcome using both plastic surgical principles and orthopedic techniques for muscle and tendon repair: bipolar muscle transfer and load-bearing muscle inset. Heretofore, transfer of the latissimus for provision of pectoralis major function has not been reported. Functional reconstruction was possible due to stable, bipolar muscle transfer with load-bearing muscle attachments into cortical bone of the anterior sternum and anteromedial aspect of the humerus. The techniques described should be within the skill set of most plastic surgeons, so that functional restoration for those with Poland syndrome is possible and accessible.

Using 25 Percent / 75 Percent ATJ/JP-8 Blend Rotary Fuel Injection Pump Wear Testing at Elevated Temperature

DTIC Science & Technology

2015-09-01

Transfer Pump Liner before Testing with 25/75 ATJ/JP-8 Fuel with 9-ppm CI/LI...46 Figure 26. Pump SN:16756534 Transfer Pump Liner with 251-hours Testing with 25/75 ATJ/JP-8 Fuel...Transfer Pump Liner before Testing with 25/75 ATJ/JP-8 Fuel with 9-ppm CI/LI

Testing of Prototype Magnetic Suspension Cryogenic Transfer Line

NASA Astrophysics Data System (ADS)

Fesmire, J. E.; Augustynowicz, S. D.; Nagy, Z. F.; Sojourner, S. J.; Shu, Q. S.; Cheng, G.; Susta, J. T.

2006-04-01

A 6-meter prototype cryogenic transfer line with magnetic suspension was tested for its mechanical and thermal performance at the Cryogenics Test Laboratory of NASA Kennedy Space Center (KSC). A test facility with two cryogenic end-boxes was designed and commissioned for the testing. Suspension mechanisms were verified through a series of tests with liquid nitrogen. The thermal performance of the prototype was determined using the new test apparatus. The tested prototype has incorporated temperature and vacuum pressure data acquisition ports, customized interfaces to cryogenic end-boxes, and instrumentation. All tests were conducted under simulated onsite transfer line working conditions. A static (boiloff rate measurement) testing method was employed to demonstrate the gross heat leak in the tested article. The real-time temperature distribution, vacuum level, levitation distance, and mass flow rate were measured. The main purpose of this paper is to summarize the testing facility design and preparation, test procedure, and primary test results. Special arrangements (such as turning on/off mechanical support units, observing levitation gap, and setting up the flowmeter) in testing of such a magnetically levitated transfer line are also discussed. Preliminary results show that the heat leak reduction of approximately one-third to one-half is achievable through such transfer lines with a magnetic suspension system.

T-Pharmacytes for Prostate Cancer Immunotherapy

DTIC Science & Technology

2013-06-01

Overexpression of CD70 by endogenous APCs enhances priming of T cells against the EL4 -NP and B6F10 tumor cell lines (9, 28). Furthermore, activation of...Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Adoptive cell therapy (ACT) of cancer with ex vivo activated/expanded T- cells is one...of the promising treatments currently being tested in patients. One challenge of the approach is that the transferred T cells become functionally

Mitochondrial Transfer from Wharton's Jelly Mesenchymal Stem Cell to MERRF Cybrid Reduces Oxidative Stress and Improves Mitochondrial Bioenergetics

PubMed Central

Liou, Chia-Wei; Chen, Shang-Der; Wang, Pei-Wen; Chuang, Jiin-Haur; Tiao, Mao-Meng; Hsu, Te-Yao

2017-01-01

Myoclonus epilepsy associated with ragged-red fibers (MERRF) is a maternally inherited mitochondrial disease affecting neuromuscular functions. Mt.8344A>G mutation in mitochondrial DNA (mtDNA) is the most common cause of MERRF syndrome and has been linked to an increase in reactive oxygen species (ROS) level and oxidative stress, as well as impaired mitochondrial bioenergetics. Here, we tested whether WJMSC has therapeutic potential for the treatment of MERRF syndrome through the transfer of mitochondria. The MERRF cybrid cells exhibited a high mt.8344A>G mutation ratio, enhanced ROS level and oxidative damage, impaired mitochondrial bioenergetics, defected mitochondria-dependent viability, exhibited an imbalance of mitochondrial dynamics, and are susceptible to apoptotic stress. Coculture experiments revealed that mitochondria were intercellularly conducted from the WJMSC to the MERRF cybrid. Furthermore, WJMSC transferred mitochondria exclusively to cells with defective mitochondria but not to cells with normal mitochondria. MERRF cybrid following WJMSC coculture (MF+WJ) demonstrated improvement of mt.8344A>G mutation ratio, ROS level, oxidative damage, mitochondrial bioenergetics, mitochondria-dependent viability, balance of mitochondrial dynamics, and resistance against apoptotic stress. WJMSC-derived mitochondrial transfer and its therapeutic effect were noted to be blocked by F-actin depolymerizing agent cytochalasin B. Collectively, the WJMSC ability to rescue cells with defective mitochondrial function through donating healthy mitochondria may lead to new insights into the development of more efficient strategies to treat diseases related to mitochondrial dysfunction. PMID:28607632

Does self-efficacy mediate transfer effects in the learning of easy and difficult motor skills?

PubMed

Stevens, David; Anderson, David I; O'Dwyer, Nicholas J; Mark Williams, A

2012-09-01

The effect of task difficulty on inter-task transfer is a classic issue in motor learning. We examined the relation between self-efficacy and transfer of learning after practicing different versions of a stick balancing task. Practicing the same task or an easier version led to significant pre- to post-test transfer of learning, whereas practicing a more difficult version did not. Self-efficacy increased modestly from pre- to post-test with easy practice, but decreased significantly with difficult practice. In addition, self-efficacy immediately prior to the post-test was significantly lower after difficult practice than easy or intermediate practice. Self-efficacy immediately prior to the post-test, performance at the end of practice, and pre-test performance explained 75% of the variance in post-test performance. The mediating role of self-efficacy on transfer of learning offers an alternative explanation for recent findings on the superiority of easy-to-difficult transfer and may help clarify inconsistencies in earlier research. Copyright © 2012 Elsevier Inc. All rights reserved.

Binary pseudo-random patterned structures for modulation transfer function calibration and resolution characterization of a full-field transmission soft x-ray microscope

DOE PAGES

Yashchuk, V. V.; Fischer, P. J.; Chan, E. R.; ...

2015-12-09

We present a modulation transfer function (MTF) calibration method based on binary pseudo-random (BPR) one-dimensional sequences and two-dimensional arrays as an effective method for spectral characterization in the spatial frequency domain of a broad variety of metrology instrumentation, including interferometric microscopes, scatterometers, phase shifting Fizeau interferometers, scanning and transmission electron microscopes, and at this time, x-ray microscopes. The inherent power spectral density of BPR gratings and arrays, which has a deterministic white-noise-like character, allows a direct determination of the MTF with a uniform sensitivity over the entire spatial frequency range and field of view of an instrument. We demonstrate themore » MTF calibration and resolution characterization over the full field of a transmission soft x-ray microscope using a BPR multilayer (ML) test sample with 2.8 nm fundamental layer thickness. We show that beyond providing a direct measurement of the microscope's MTF, tests with the BPRML sample can be used to fine tune the instrument's focal distance. Finally, our results confirm the universality of the method that makes it applicable to a large variety of metrology instrumentation with spatial wavelength bandwidths from a few nanometers to hundreds of millimeters.« less

Predicting vertically-nonsequential wetting patterns with a source-responsive model

USGS Publications Warehouse

Nimmo, John R.; Mitchell, Lara

2013-01-01

Water infiltrating into soil of natural structure often causes wetting patterns that do not develop in an orderly sequence. Because traditional unsaturated flow models represent a water advance that proceeds sequentially, they fail to predict irregular development of water distribution. In the source-responsive model, a diffuse domain (D) represents flow within soil matrix material following traditional formulations, and a source-responsive domain (S), characterized in terms of the capacity for preferential flow and its degree of activation, represents preferential flow as it responds to changing water-source conditions. In this paper we assume water undergoing rapid source-responsive transport at any particular time is of negligibly small volume; it becomes sensible at the time and depth where domain transfer occurs. A first-order transfer term represents abstraction from the S to the D domain which renders the water sensible. In tests with lab and field data, for some cases the model shows good quantitative agreement, and in all cases it captures the characteristic patterns of wetting that proceed nonsequentially in the vertical direction. In these tests we determined the values of the essential characterizing functions by inverse modeling. These functions relate directly to observable soil characteristics, rendering them amenable to evaluation and improvement through hydropedologic development.

Performance of Optimized Actuator and Sensor Arrays in an Active Noise Control System

NASA Technical Reports Server (NTRS)

Palumbo, D. L.; Padula, S. L.; Lyle, K. H.; Cline, J. H.; Cabell, R. H.

1996-01-01

Experiments have been conducted in NASA Langley's Acoustics and Dynamics Laboratory to determine the effectiveness of optimized actuator/sensor architectures and controller algorithms for active control of harmonic interior noise. Tests were conducted in a large scale fuselage model - a composite cylinder which simulates a commuter class aircraft fuselage with three sections of trim panel and a floor. Using an optimization technique based on the component transfer functions, combinations of 4 out of 8 piezoceramic actuators and 8 out of 462 microphone locations were evaluated against predicted performance. A combinatorial optimization technique called tabu search was employed to select the optimum transducer arrays. Three test frequencies represent the cases of a strong acoustic and strong structural response, a weak acoustic and strong structural response and a strong acoustic and weak structural response. Noise reduction was obtained using a Time Averaged/Gradient Descent (TAGD) controller. Results indicate that the optimization technique successfully predicted best and worst case performance. An enhancement of the TAGD control algorithm was also evaluated. The principal components of the actuator/sensor transfer functions were used in the PC-TAGD controller. The principal components are shown to be independent of each other while providing control as effective as the standard TAGD.

Category inference as a function of correlational structure, category discriminability, and number of available cues.

PubMed

Lancaster, Matthew E; Shelhamer, Ryan; Homa, Donald

2013-04-01

Two experiments investigated category inference when categories were composed of correlated or uncorrelated dimensions and the categories overlapped minimally or moderately. When the categories minimally overlapped, the dimensions were strongly correlated with the category label. Following a classification learning phase, subsequent transfer required the selection of either a category label or a feature when one, two, or three features were missing. Experiments 1 and 2 differed primarily in the number of learning blocks prior to transfer. In each experiment, the inference of the category label or category feature was influenced by both dimensional and category correlations, as well as their interaction. The number of cues available at test impacted performance more when the dimensional correlations were zero and category overlap was high. However, a minimal number of cues were sufficient to produce high levels of inference when the dimensions were highly correlated; additional cues had a positive but reduced impact, even when overlap was high. Subjects were generally more accurate in inferring the category label than a category feature regardless of dimensional correlation, category overlap, or number of cues available at test. Whether the category label functioned as a special feature or not was critically dependent upon these embedded correlations, with feature inference driven more strongly by dimensional correlations.

Optical analysis of electro-optical systems by MTF calculus

NASA Astrophysics Data System (ADS)

Barbarini, Elisa Signoreto; Dos Santos, Daniel, Jr.; Stefani, Mário Antonio; Yasuoka, Fátima Maria Mitsue; Castro Neto, Jarbas C.; Rodrigues, Evandro Luís Linhari

2011-08-01

One of the widely used methods for performance analysis of an optical system is the determination of the Modulation Transfer Function (MTF). The MTF represents a quantitative and direct measure of image quality, and, besides being an objective test, it can be used on concatenated optical system. This paper presents the application of software called SMTF (software modulation transfer function), built in C++ and Open CV platforms for MTF calculation on electro-optical system. Through this technique, it is possible to develop specific method to measure the real time performance of a digital fundus camera, an infrared sensor and an ophthalmological surgery microscope. Each optical instrument mentioned has a particular device to measure the MTF response, which is being developed. Then the MTF information assists the analysis of the optical system alignment, and also defines its resolution limit by the MTF graphic. The result obtained from the implemented software is compared with the theoretical MTF curve from the analyzed systems.

Measurement of Motion Transfer Functions for Mirror Suspensions

NASA Astrophysics Data System (ADS)

Stuver, Amber; Beilby, Mark; Glancy, Aran; Gonzalez, Gabriela

2001-04-01

Interferometric gravitational wave detectors, such as LIGO, use mirrors suspended in pendulums. The current LIGO dectors use simple pendulums, but advanced LIGO detectors will use multiple pendulums with some stages on soft vertical springs. A drawback of the a multiple pendulum design is that it is difficult to model and predict cross couplings from one vibrational mode to another due to slight unavoidable asymmetries in the real system. Of most concern are the couplings to motion along the optical axis and into angular motions, which have the most potential to contaminate data. Our research focuses on the experimental testing of the pendulum designs for cross couplings with a special dedicated shaking stage. The cross couplings in each degree of freedom, their isolation and damping are investigated in this research though the measurement of transfer functions as filtered though the suspension system. This research is supported by The Pennsylvania State University, the NSF Grant no. PHY-9870032, and the REU program at The Pennsylvania State University.

Quantitative phase microscopy via optimized inversion of the phase optical transfer function.

PubMed

Jenkins, Micah H; Gaylord, Thomas K

2015-10-01

Although the field of quantitative phase imaging (QPI) has wide-ranging biomedical applicability, many QPI methods are not well-suited for such applications due to their reliance on coherent illumination and specialized hardware. By contrast, methods utilizing partially coherent illumination have the potential to promote the widespread adoption of QPI due to their compatibility with microscopy, which is ubiquitous in the biomedical community. Described herein is a new defocus-based reconstruction method that utilizes a small number of efficiently sampled micrographs to optimally invert the partially coherent phase optical transfer function under assumptions of weak absorption and slowly varying phase. Simulation results are provided that compare the performance of this method with similar algorithms and demonstrate compatibility with large phase objects. The accuracy of the method is validated experimentally using a microlens array as a test phase object. Lastly, time-lapse images of live adherent cells are obtained with an off-the-shelf microscope, thus demonstrating the new method's potential for extending QPI capability widely in the biomedical community.

Reduced order modeling of head related transfer functions for virtual acoustic displays

NASA Astrophysics Data System (ADS)

Willhite, Joel A.; Frampton, Kenneth D.; Grantham, D. Wesley

2003-04-01

The purpose of this work is to improve the computational efficiency in acoustic virtual applications by creating and testing reduced order models of the head related transfer functions used in localizing sound sources. State space models of varying order were generated from zero-elevation Head Related Impulse Responses (HRIRs) using Kungs Single Value Decomposition (SVD) technique. The inputs to the models are the desired azimuths of the virtual sound sources (from minus 90 deg to plus 90 deg, in 10 deg increments) and the outputs are the left and right ear impulse responses. Trials were conducted in an anechoic chamber in which subjects were exposed to real sounds that were emitted by individual speakers across a numbered speaker array, phantom sources generated from the original HRIRs, and phantom sound sources generated with the different reduced order state space models. The error in the perceived direction of the phantom sources generated from the reduced order models was compared to errors in localization using the original HRIRs.

Perceptual attributes for the comparison of head-related transfer functions.

PubMed

Simon, Laurent S R; Zacharov, Nick; Katz, Brian F G

2016-11-01

The benefit of using individual head-related transfer functions (HRTFs) in binaural audio is well documented with regards to improving localization precision. However, with the increased use of binaural audio in more complex scene renderings, cognitive studies, and virtual and augmented reality simulations, the perceptual impact of HRTF selection may go beyond simple localization. In this study, the authors develop a list of attributes which qualify the perceived differences between HRTFs, providing a qualitative understanding of the perceptual variance of non-individual binaural renderings. The list of attributes was designed using a Consensus Vocabulary Protocol elicitation method. Participants followed an Individual Vocabulary Protocol elicitation procedure, describing the perceived differences between binaural stimuli based on binauralized extracts of multichannel productions. This was followed by an automated lexical reduction and a series of consensus group meetings during which participants agreed on a list of relevant attributes. Finally, the proposed list of attributes was then evaluated through a listening test, leading to eight valid perceptual attributes for describing the perceptual dimensions affected by HRTF set variations.

A new modelling and identification scheme for time-delay systems with experimental investigation: a relay feedback approach

NASA Astrophysics Data System (ADS)

Pandey, Saurabh; Majhi, Somanath; Ghorai, Prasenjit

2017-07-01

In this paper, the conventional relay feedback test has been modified for modelling and identification of a class of real-time dynamical systems in terms of linear transfer function models with time-delay. An ideal relay and unknown systems are connected through a negative feedback loop to bring the sustained oscillatory output around the non-zero setpoint. Thereafter, the obtained limit cycle information is substituted in the derived mathematical equations for accurate identification of unknown plants in terms of overdamped, underdamped, critically damped second-order plus dead time and stable first-order plus dead time transfer function models. Typical examples from the literature are included for the validation of the proposed identification scheme through computer simulations. Subsequently, the comparisons between estimated model and true system are drawn through integral absolute error criterion and frequency response plots. Finally, the obtained output responses through simulations are verified experimentally on real-time liquid level control system using Yokogawa Distributed Control System CENTUM CS3000 set up.

Systematic study on the TD-DFT calculated electronic circular dichroism spectra of chiral aromatic nitro compounds: A comparison of B3LYP and CAM-B3LYP.

PubMed

Komjáti, Balázs; Urai, Ákos; Hosztafi, Sándor; Kökösi, József; Kováts, Benjámin; Nagy, József; Horváth, Péter

2016-02-15

B3LYP is one of the most widely used functional for the prediction of electronic circular dichroism spectra, however if the studied molecule contains aromatic nitro group computations may fail to produce reliable results. A test set of molecules of known stereochemistry were synthesized to study this phenomenon in detail. Spectra were computed by B3LYP and CAM-B3LYP functionals with 6-311++G(2d,2p) basis set. It was found that the range separated CAM-B3LYP gives better predictions than B3LYP for all test molecules. Fragment population analysis revealed that the nitro groups form highly localized molecule orbitals but the exact composition depends on the functional. CAM-B3LYP allows sufficient spatial overlap between the nitro group and distant parts of the molecule, which is necessary for the accurate description of excited states especially for charge transfer states. This phenomenon and the synthesized test molecules can be used to benchmark theoretical methods as well as to help the development of new functionals intended for spectroscopical studies. Copyright © 2015 Elsevier B.V. All rights reserved.

LANDSAT-D investigations in snow hydrology

NASA Technical Reports Server (NTRS)

Dozier, J.

1983-01-01

The atmospheric radiative transfer calculation program (ATARD) and its supporting programs (setting up atmospheric profile, making Mie tables and an exponential-sum-fitting table) were completed. More sophisticated treatment of aerosol scattering (including angular phase function or asymmetric factor) and multichannel analysis of results from ATRAD are being developed. Some progress was made on a Monte Carlo program for examining two dimensional effects, specifically a surface boundary condition that varies across a scene. The MONTE program combines ATRAD and the Monte Carlo method together to produce an atmospheric point spread function. Currently the procedure passes monochromatic tests and the results are reasonable.

Delegation to automaticity: the driving force for cognitive evolution?

PubMed

Shine, J M; Shine, R

2014-01-01

The ability to delegate control over repetitive tasks from higher to lower neural centers may be a fundamental innovation in human cognition. Plausibly, the massive neurocomputational challenges associated with the mastery of balance during the evolution of bipedality in proto-humans provided a strong selective advantage to individuals with brains capable of efficiently transferring tasks in this way. Thus, the shift from quadrupedal to bipedal locomotion may have driven the rapid evolution of distinctive features of human neuronal functioning. We review recent studies of functional neuroanatomy that bear upon this hypothesis, and identify ways to test our ideas.

Paraplegia due to adrenomyeloneuropathy.

PubMed

Lamid, S; El Ghatit, A Z

1984-04-01

Only nine cases of adrenomyeloneuropathy have been reported in the literature. It manifested as adrenal insufficiency, spastic paraparesis, loss of bowel, bladder and sexual functions, and peripheral neuropathy. Our paper describes a patient with the diagnosis of adrenomyeloneuropathy who was admitted to our hospital for rehabilitation. Family and neurological history, physical examination and special laboratory studies such as ACTH stimulation test, electrodiagnostic findings, cystometrogram and sexual function evaluation were essential to establish the diagnosis of this disease. His rehabilitation consisted of bowel and bladder training, ambulation with long-leg braces and crutches, wheelchair mobilization and transfers, and independence of all activities of daily living.

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

NASA Technical Reports Server (NTRS)

Frady, Gregory P.; Duvall, Lowery D.; Fulcher, Clay W. G.; Laverde, Bruce T.; Hunt, Ronald A.

2011-01-01

rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for component-loaded curved orthogrid panels typical of launch vehicle skin structures. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was applied to correlate the measured input sound pressures across the energized panel. This application quantifies the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software developed for the RPTF method allows easy replacement of the diffuse acoustic field with other pressure fields such as a turbulent boundary layer (TBL) model suitable for vehicle ascent. Structural responses using a TBL model were demonstrated, and wind tunnel tests have been proposed to anchor the predictions and provide new insight into modeling approaches for this environment. Finally, design load factors were developed from the measured and predicted responses and compared with those derived from traditional techniques such as historical Mass Acceleration Curves and Barrett scaling methods for acreage and component-loaded panels.

Statistical Time Series Models of Pilot Control with Applications to Instrument Discrimination

NASA Technical Reports Server (NTRS)

Altschul, R. E.; Nagel, P. M.; Oliver, F.

1984-01-01

A general description of the methodology used in obtaining the transfer function models and verification of model fidelity, frequency domain plots of the modeled transfer functions, numerical results obtained from an analysis of poles and zeroes obtained from z plane to s-plane conversions of the transfer functions, and the results of a study on the sequential introduction of other variables, both exogenous and endogenous into the loop are contained.

Transfer Function Control for Biometric Monitoring System

NASA Technical Reports Server (NTRS)

Chmiel, Alan J. (Inventor); Grodinsky, Carlos M. (Inventor); Humphreys, Bradley T. (Inventor)

2015-01-01

A modular apparatus for acquiring biometric data may include circuitry operative to receive an input signal indicative of a biometric condition, the circuitry being configured to process the input signal according to a transfer function thereof and to provide a corresponding processed input signal. A controller is configured to provide at least one control signal to the circuitry to programmatically modify the transfer function of the modular system to facilitate acquisition of the biometric data.

Graphic design of pinhole cameras

NASA Technical Reports Server (NTRS)

Edwards, H. B.; Chu, W. P.

1979-01-01

The paper describes a graphic technique for the analysis and optimization of pinhole size and focal length. The technique is based on the use of the transfer function of optical elements described by Scott (1959) to construct the transfer function of a circular pinhole camera. This transfer function is the response of a component or system to a pattern of lines having a sinusoidally varying radiance at varying spatial frequencies. Some specific examples of graphic design are presented.

An asymptotic preserving unified gas kinetic scheme for frequency-dependent radiative transfer equations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Wenjun, E-mail: sun_wenjun@iapcm.ac.cn; Jiang, Song, E-mail: jiang@iapcm.ac.cn; Xu, Kun, E-mail: makxu@ust.hk

This paper presents an extension of previous work (Sun et al., 2015 [22]) of the unified gas kinetic scheme (UGKS) for the gray radiative transfer equations to the frequency-dependent (multi-group) radiative transfer system. Different from the gray radiative transfer equations, where the optical opacity is only a function of local material temperature, the simulation of frequency-dependent radiative transfer is associated with additional difficulties from the frequency-dependent opacity. For the multiple frequency radiation, the opacity depends on both the spatial location and the frequency. For example, the opacity is typically a decreasing function of frequency. At the same spatial region themore » transport physics can be optically thick for the low frequency photons, and optically thin for high frequency ones. Therefore, the optical thickness is not a simple function of space location. In this paper, the UGKS for frequency-dependent radiative system is developed. The UGKS is a finite volume method and the transport physics is modeled according to the ratio of the cell size to the photon's frequency-dependent mean free path. When the cell size is much larger than the photon's mean free path, a diffusion solution for such a frequency radiation will be obtained. On the other hand, when the cell size is much smaller than the photon's mean free path, a free transport mechanism will be recovered. In the regime between the above two limits, with the variation of the ratio between the local cell size and photon's mean free path, the UGKS provides a smooth transition in the physical and frequency space to capture the corresponding transport physics accurately. The seemingly straightforward extension of the UGKS from the gray to multiple frequency radiation system is due to its intrinsic consistent multiple scale transport modeling, but it still involves lots of work to properly discretize the multiple groups in order to design an asymptotic preserving (AP) scheme in all regimes. The current scheme is tested in a few frequency-dependent radiation problems, and the results are compared with the solutions from the well-defined implicit Monte Carlo (IMC) method. The UGKS is much more efficient than IMC, and the computational times of both schemes for all test cases are listed. The UGKS seems to be the first discrete ordinate method (DOM) for the accurate capturing of multiple frequency radiative transport physics from ballistic particle motion to the diffusive wave propagation.« less