Joint Transmit Power Allocation and Splitting for SWIPT Aided OFDM-IDMA in Wireless Sensor Networks.

PubMed

Li, Shanshan; Zhou, Xiaotian; Wang, Cheng-Xiang; Yuan, Dongfeng; Zhang, Wensheng

2017-07-04

In this paper, we propose to combine Orthogonal Frequency Division Multiplexing-Interleave Division Multiple Access (OFDM-IDMA) with Simultaneous Wireless Information and Power Transfer (SWIPT), resulting in SWIPT aided OFDM-IDMA scheme for power-limited sensor networks. In the proposed system, the Receive Node (RN) applies Power Splitting (PS) to coordinate the Energy Harvesting (EH) and Information Decoding (ID) process, where the harvested energy is utilized to guarantee the iterative Multi-User Detection (MUD) of IDMA to work under sufficient number of iterations. Our objective is to minimize the total transmit power of Source Node (SN), while satisfying the requirements of both minimum harvested energy and Bit Error Rate (BER) performance from individual receive nodes. We formulate such a problem as a joint power allocation and splitting one, where the iteration number of MUD is also taken into consideration as the key parameter to affect both EH and ID constraints. To solve it, a sub-optimal algorithm is proposed to determine the power profile, PS ratio and iteration number of MUD in an iterative manner. Simulation results verify that the proposed algorithm can provide significant performance improvement.

Power allocation strategies to minimize energy consumption in wireless body area networks.

PubMed

Kailas, Aravind

2011-01-01

The wide scale deployment of wireless body area networks (WBANs) hinges on designing energy efficient communication protocols to support the reliable communication as well as to prolong the network lifetime. Cooperative communications, a relatively new idea in wireless communications, offers the benefits of multi-antenna systems, thereby improving the link reliability and boosting energy efficiency. In this short paper, the advantages of resorting to cooperative communications for WBANs in terms of minimized energy consumption are investigated. Adopting an energy model that encompasses energy consumptions in the transmitter and receiver circuits, and transmitting energy per bit, it is seen that cooperative transmission can improve energy efficiency of the wireless network. In particular, the problem of optimal power allocation is studied with the constraint of targeted outage probability. Two strategies of power allocation are considered: power allocation with and without posture state information. Using analysis and simulation-based results, two key points are demonstrated: (i) allocating power to the on-body sensors making use of the posture information can reduce the total energy consumption of the WBAN; and (ii) when the channel condition is good, it is better to recruit less relays for cooperation to enhance energy efficiency.

Optimal Resource Allocation for NOMA-TDMA Scheme with α-Fairness in Industrial Internet of Things.

PubMed

Sun, Yanjing; Guo, Yiyu; Li, Song; Wu, Dapeng; Wang, Bin

2018-05-15

In this paper, a joint non-orthogonal multiple access and time division multiple access (NOMA-TDMA) scheme is proposed in Industrial Internet of Things (IIoT), which allowed multiple sensors to transmit in the same time-frequency resource block using NOMA. The user scheduling, time slot allocation, and power control are jointly optimized in order to maximize the system α -fair utility under transmit power constraint and minimum rate constraint. The optimization problem is nonconvex because of the fractional objective function and the nonconvex constraints. To deal with the original problem, we firstly convert the objective function in the optimization problem into a difference of two convex functions (D.C.) form, and then propose a NOMA-TDMA-DC algorithm to exploit the global optimum. Numerical results show that the NOMA-TDMA scheme significantly outperforms the traditional orthogonal multiple access scheme in terms of both spectral efficiency and user fairness.

Optimal power allocation and joint source-channel coding for wireless DS-CDMA visual sensor networks

NASA Astrophysics Data System (ADS)

Pandremmenou, Katerina; Kondi, Lisimachos P.; Parsopoulos, Konstantinos E.

2011-01-01

In this paper, we propose a scheme for the optimal allocation of power, source coding rate, and channel coding rate for each of the nodes of a wireless Direct Sequence Code Division Multiple Access (DS-CDMA) visual sensor network. The optimization is quality-driven, i.e. the received quality of the video that is transmitted by the nodes is optimized. The scheme takes into account the fact that the sensor nodes may be imaging scenes with varying levels of motion. Nodes that image low-motion scenes will require a lower source coding rate, so they will be able to allocate a greater portion of the total available bit rate to channel coding. Stronger channel coding will mean that such nodes will be able to transmit at lower power. This will both increase battery life and reduce interference to other nodes. Two optimization criteria are considered. One that minimizes the average video distortion of the nodes and one that minimizes the maximum distortion among the nodes. The transmission powers are allowed to take continuous values, whereas the source and channel coding rates can assume only discrete values. Thus, the resulting optimization problem lies in the field of mixed-integer optimization tasks and is solved using Particle Swarm Optimization. Our experimental results show the importance of considering the characteristics of the video sequences when determining the transmission power, source coding rate and channel coding rate for the nodes of the visual sensor network.

Performance analysis of optimal power allocation in wireless cooperative communication systems

NASA Astrophysics Data System (ADS)

Babikir Adam, Edriss E.; Samb, Doudou; Yu, Li

2013-03-01

Cooperative communication has been recently proposed in wireless communication systems for exploring the inherent spatial diversity in relay channels.The Amplify-and-Forward (AF) cooperation protocols with multiple relays have not been sufficiently investigated even if it has a low complexity in term of implementation. We consider in this work a cooperative diversity system in which a source transmits some information to a destination with the help of multiple relay nodes with AF protocols and investigate the optimality of allocating powers both at the source and the relays system by optimizing the symbol error rate (SER) performance in an efficient way. Firstly we derive a closedform SER formulation for MPSK signal using the concept of moment generating function and some statistical approximations in high signal to noise ratio (SNR) for the system under studied. We then find a tight corresponding lower bound which converges to the same limit as the theoretical upper bound and develop an optimal power allocation (OPA) technique with mean channel gains to minimize the SER. Simulation results show that our scheme outperforms the equal power allocation (EPA) scheme and is tight to the theoretical approximation based on the SER upper bound in high SNR for different number of relays.

Optimal Time Allocation in Backscatter Assisted Wireless Powered Communication Networks.

PubMed

Lyu, Bin; Yang, Zhen; Gui, Guan; Sari, Hikmet

2017-06-01

This paper proposes a wireless powered communication network (WPCN) assisted by backscatter communication (BackCom). This model consists of a power station, an information receiver and multiple users that can work in either BackCom mode or harvest-then-transmit (HTT) mode. The time block is mainly divided into two parts corresponding to the data backscattering and transmission periods, respectively. The users first backscatter data to the information receiver in time division multiple access (TDMA) during the data backscattering period. When one user works in the BackCom mode, the other users harvest energy from the power station. During the data transmission period, two schemes, i.e., non-orthogonal multiple access (NOMA) and TDMA, are considered. To maximize the system throughput, the optimal time allocation policies are obtained. Simulation results demonstrate the superiority of the proposed model.

Optimal Time Allocation in Backscatter Assisted Wireless Powered Communication Networks

PubMed Central

Lyu, Bin; Yang, Zhen; Gui, Guan; Sari, Hikmet

2017-01-01

This paper proposes a wireless powered communication network (WPCN) assisted by backscatter communication (BackCom). This model consists of a power station, an information receiver and multiple users that can work in either BackCom mode or harvest-then-transmit (HTT) mode. The time block is mainly divided into two parts corresponding to the data backscattering and transmission periods, respectively. The users first backscatter data to the information receiver in time division multiple access (TDMA) during the data backscattering period. When one user works in the BackCom mode, the other users harvest energy from the power station. During the data transmission period, two schemes, i.e., non-orthogonal multiple access (NOMA) and TDMA, are considered. To maximize the system throughput, the optimal time allocation policies are obtained. Simulation results demonstrate the superiority of the proposed model. PMID:28587171

Budget Allocation in a Competitive Communication Spectrum Economy

NASA Astrophysics Data System (ADS)

Lin, Ming-Hua; Tsai, Jung-Fa; Ye, Yinyu

2009-12-01

This study discusses how to adjust "monetary budget" to meet each user's physical power demand, or balance all individual utilities in a competitive "spectrum market" of a communication system. In the market, multiple users share a common frequency or tone band and each of them uses the budget to purchase its own transmit power spectra (taking others as given) in maximizing its Shannon utility or pay-off function that includes the effect of interferences. A market equilibrium is a budget allocation, price spectrum, and tone power distribution that independently and simultaneously maximizes each user's utility. The equilibrium conditions of the market are formulated and analyzed, and the existence of an equilibrium is proved. Computational results and comparisons between the competitive equilibrium and Nash equilibrium solutions are also presented, which show that the competitive market equilibrium solution often provides more efficient power distribution.

Power Saving Control for Battery-Powered Portable WLAN APs

NASA Astrophysics Data System (ADS)

Ogawa, Masakatsu; Hiraguri, Takefumi

This paper proposes a power saving control function for battery-powered portable wireless LAN (WLAN) access points (APs) to extend the battery life. The IEEE802.11 standard does not support power saving control for APs. To enable a sleep state for an AP, the AP forces the stations (STAs) to refrain from transmitting frames using the network allocation vector (NAV) while the AP is sleeping. Thus the sleep state for the AP can be employed without causing frame loss at the STAs. Numerical analysis and computer simulation reveal that the newly proposed control technique conserves power compared to the conventional control.

Power allocation for SWIPT in K-user interference channels using game theory

NASA Astrophysics Data System (ADS)

Wen, Zhigang; Liu, Ying; Liu, Xiaoqing; Li, Shan; Chen, Xianya

2018-12-01

A simultaneous wireless information and power transfer system in interference channels of multi-users is considered. In this system, each transmitter sends one data stream to its targeted receiver, which causes interference to other receivers. Since all transmitter-receiver links want to maximize their own average transmission rate, a power allocation problem under the transmit power constraints and the energy-harvesting constraints is developed. To solve this problem, we propose a game theory framework. Then, we convert the game into a variational inequalities problem by establishing the connection between game theory and variational inequalities and solve the variational inequalities problem. Through theoretical analysis, the existence and uniqueness of Nash equilibrium are both guaranteed by the theory of variational inequalities. A distributed iterative alternating optimization water-filling algorithm is derived, which is proved to converge. Numerical results show that the proposed algorithm reaches fast convergence and achieves a higher sum rate than the unaided scheme.

Power-efficient distributed resource allocation under goodput QoS constraints for heterogeneous networks

NASA Astrophysics Data System (ADS)

Andreotti, Riccardo; Del Fiorentino, Paolo; Giannetti, Filippo; Lottici, Vincenzo

2016-12-01

This work proposes a distributed resource allocation (RA) algorithm for packet bit-interleaved coded OFDM transmissions in the uplink of heterogeneous networks (HetNets), characterized by small cells deployed over a macrocell area and sharing the same band. Every user allocates its transmission resources, i.e., bits per active subcarrier, coding rate, and power per subcarrier, to minimize the power consumption while both guaranteeing a target quality of service (QoS) and accounting for the interference inflicted by other users transmitting over the same band. The QoS consists of the number of information bits delivered in error-free packets per unit of time, or goodput (GP), estimated at the transmitter by resorting to an efficient effective SNR mapping technique. First, the RA problem is solved in the point-to-point case, thus deriving an approximate yet accurate closed-form expression for the power allocation (PA). Then, the interference-limited HetNet case is examined, where the RA problem is described as a non-cooperative game, providing a solution in terms of generalized Nash equilibrium. Thanks to the closed-form of the PA, the solution analysis is based on the best response concept. Hence, sufficient conditions for existence and uniqueness of the solution are analytically derived, along with a distributed algorithm capable of reaching the game equilibrium.

An Adaptive Cooperative Strategy for Underlay MIMO Cognitive Radio Networks: An Opportunistic and Low-Complexity Approach

NASA Astrophysics Data System (ADS)

Mazoochi, M.; Pourmina, M. A.; Bakhshi, H.

2015-03-01

The core aim of this work is the maximization of the achievable data rate of the secondary user pairs (SU pairs), while ensuring the QoS of primary users (PUs). All users are assumed to be equipped with multiple antennas. It is assumed that when PUs are present, the direct communications between SU pairs introduces intolerable interference to PUs and thereby SUs transmit signal using the cooperation of other SUs and avoid transmitting in the direct channel. In brief, an adaptive cooperative strategy for multiple-input/multiple-output (MIMO) cognitive radio networks is proposed. At the presence of PUs, the issue of joint relay selection and power allocation in Underlay MIMO Cooperative Cognitive Radio Networks (U-MIMO-CCRN) is addressed. The optimal approach for determining the power allocation and the cooperating SU is proposed. Besides, the outage probability of the proposed communication protocol is further derived. Due to high complexity of the optimal approach, a low-complexity approach is further proposed and its performance is evaluated using simulations. The simulation results reveal that the performance loss due to the low-complexity approach is only about 14%, while the complexity is greatly reduced.

Joint subchannel pairing and power control for cognitive radio networks with amplify-and-forward relaying.

PubMed

Shen, Yanyan; Wang, Shuqiang; Wei, Zhiming

2014-01-01

Dynamic spectrum sharing has drawn intensive attention in cognitive radio networks. The secondary users are allowed to use the available spectrum to transmit data if the interference to the primary users is maintained at a low level. Cooperative transmission for secondary users can reduce the transmission power and thus improve the performance further. We study the joint subchannel pairing and power allocation problem in relay-based cognitive radio networks. The objective is to maximize the sum rate of the secondary user that is helped by an amplify-and-forward relay. The individual power constraints at the source and the relay, the subchannel pairing constraints, and the interference power constraints are considered. The problem under consideration is formulated as a mixed integer programming problem. By the dual decomposition method, a joint optimal subchannel pairing and power allocation algorithm is proposed. To reduce the computational complexity, two suboptimal algorithms are developed. Simulations have been conducted to verify the performance of the proposed algorithms in terms of sum rate and average running time under different conditions.

Waveform Design for Wireless Power Transfer

NASA Astrophysics Data System (ADS)

Clerckx, Bruno; Bayguzina, Ekaterina

2016-12-01

Far-field Wireless Power Transfer (WPT) has attracted significant attention in recent years. Despite the rapid progress, the emphasis of the research community in the last decade has remained largely concentrated on improving the design of energy harvester (so-called rectenna) and has left aside the effect of transmitter design. In this paper, we study the design of transmit waveform so as to enhance the DC power at the output of the rectenna. We derive a tractable model of the non-linearity of the rectenna and compare with a linear model conventionally used in the literature. We then use those models to design novel multisine waveforms that are adaptive to the channel state information (CSI). Interestingly, while the linear model favours narrowband transmission with all the power allocated to a single frequency, the non-linear model favours a power allocation over multiple frequencies. Through realistic simulations, waveforms designed based on the non-linear model are shown to provide significant gains (in terms of harvested DC power) over those designed based on the linear model and over non-adaptive waveforms. We also compute analytically the theoretical scaling laws of the harvested energy for various waveforms as a function of the number of sinewaves and transmit antennas. Those scaling laws highlight the benefits of CSI knowledge at the transmitter in WPT and of a WPT design based on a non-linear rectenna model over a linear model. Results also motivate the study of a promising architecture relying on large-scale multisine multi-antenna waveforms for WPT. As a final note, results stress the importance of modeling and accounting for the non-linearity of the rectenna in any system design involving wireless power.

Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks.

PubMed

Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

2017-05-16

In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks.

Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks

PubMed Central

Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

2017-01-01

In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks. PMID:28509841

Antenna Allocation in MIMO Radar with Widely Separated Antennas for Multi-Target Detection

PubMed Central

Gao, Hao; Wang, Jian; Jiang, Chunxiao; Zhang, Xudong

2014-01-01

In this paper, we explore a new resource called multi-target diversity to optimize the performance of multiple input multiple output (MIMO) radar with widely separated antennas for detecting multiple targets. In particular, we allocate antennas of the MIMO radar to probe different targets simultaneously in a flexible manner based on the performance metric of relative entropy. Two antenna allocation schemes are proposed. In the first scheme, each antenna is allocated to illuminate a proper target over the entire illumination time, so that the detection performance of each target is guaranteed. The problem is formulated as a minimum makespan scheduling problem in the combinatorial optimization framework. Antenna allocation is implemented through a branch-and-bound algorithm and an enhanced factor 2 algorithm. In the second scheme, called antenna-time allocation, each antenna is allocated to illuminate different targets with different illumination time. Both antenna allocation and time allocation are optimized based on illumination probabilities. Over a large range of transmitted power, target fluctuations and target numbers, both of the proposed antenna allocation schemes outperform the scheme without antenna allocation. Moreover, the antenna-time allocation scheme achieves a more robust detection performance than branch-and-bound algorithm and the enhanced factor 2 algorithm when the target number changes. PMID:25350505

Antenna allocation in MIMO radar with widely separated antennas for multi-target detection.

PubMed

Gao, Hao; Wang, Jian; Jiang, Chunxiao; Zhang, Xudong

2014-10-27

In this paper, we explore a new resource called multi-target diversity to optimize the performance of multiple input multiple output (MIMO) radar with widely separated antennas for detecting multiple targets. In particular, we allocate antennas of the MIMO radar to probe different targets simultaneously in a flexible manner based on the performance metric of relative entropy. Two antenna allocation schemes are proposed. In the first scheme, each antenna is allocated to illuminate a proper target over the entire illumination time, so that the detection performance of each target is guaranteed. The problem is formulated as a minimum makespan scheduling problem in the combinatorial optimization framework. Antenna allocation is implemented through a branch-and-bound algorithm and an enhanced factor 2 algorithm. In the second scheme, called antenna-time allocation, each antenna is allocated to illuminate different targets with different illumination time. Both antenna allocation and time allocation are optimized based on illumination probabilities. Over a large range of transmitted power, target fluctuations and target numbers, both of the proposed antenna allocation schemes outperform the scheme without antenna allocation. Moreover, the antenna-time allocation scheme achieves a more robust detection performance than branch-and-bound algorithm and the enhanced factor 2 algorithm when the target number changes.

Hybrid digital-analog video transmission in wireless multicast and multiple-input multiple-output system

NASA Astrophysics Data System (ADS)

Liu, Yu; Lin, Xiaocheng; Fan, Nianfei; Zhang, Lin

2016-01-01

Wireless video multicast has become one of the key technologies in wireless applications. But the main challenge of conventional wireless video multicast, i.e., the cliff effect, remains unsolved. To overcome the cliff effect, a hybrid digital-analog (HDA) video transmission framework based on SoftCast, which transmits the digital bitstream with the quantization residuals, is proposed. With an effective power allocation algorithm and appropriate parameter settings, the residual gains can be maximized; meanwhile, the digital bitstream can assure transmission of a basic video to the multicast receiver group. In the multiple-input multiple-output (MIMO) system, since nonuniform noise interference on different antennas can be regarded as the cliff effect problem, ParCast, which is a variation of SoftCast, is also applied to video transmission to solve it. The HDA scheme with corresponding power allocation algorithms is also applied to improve video performance. Simulations show that the proposed HDA scheme can overcome the cliff effect completely with the transmission of residuals. What is more, it outperforms the compared WSVC scheme by more than 2 dB when transmitting under the same bandwidth, and it can further improve performance by nearly 8 dB in MIMO when compared with the ParCast scheme.

A power allocation method for 2 × 2 VLC-MIMO indoor communication

NASA Astrophysics Data System (ADS)

Dai, Mingjun; Yuan, Jing; Feng, Renhai; Wang, Hui; Chen, Bin; Lin, Xiaohui

2016-08-01

Visible light communication (VLC) has been a promising field of optical communications which focuses on visible light spectrum that humans can see. Unlike existing studies which mainly discuss point-to-point communication, in this paper, we consider a VLC network, in particular a 2 × 2 system. Our focus is on dealing with interference in this network. The objective is to maximize the signal to interference plus noise ratio (SINR) of one receiver for a given SINR of another receiver. We formulate a power allocation optimization problem to deal with such interference, and introduce dichotomy to solve this optimization problem. Simulation results have twofold meaning: First, SINR_1 increases with the growth of SINR_2, which are the SINR of the two receivers, respectively. Second, our proposed scheme outperforms the classical time-division multiple access technique in terms of transmit powers of both light sources when the data rate for these two schemes are set to be identical for each user, respectively.

Framework for power and activity factor allocation in a multiclass CDMA system

NASA Astrophysics Data System (ADS)

Wu, Xinzhou; Srikant, Rayadurgam

2001-07-01

We consider a multimedia CDMA uplink where there are multiple classes of users with different Quality-of-Service (QoS) requirements. Each user is modeled as an ON-OFF source, where in the ON state, the user transmits a fixed number of bits in each time slot and in the OFF state, the user is silent. The probability of being in the ON state, known as the activity factor, could be different for different users. Assuming a constant channel gain, we first characterize the set of transmit power levels, activity factors and number of users in each class that can be supported by a system with a given spreading gain under the constraint that each user's QoS requirement must be met. Using this characterization, we then present a utility function-based algorithm for choosing the activity factors of elastic users in the network.

Motion-related resource allocation in dynamic wireless visual sensor network environments.

PubMed

Katsenou, Angeliki V; Kondi, Lisimachos P; Parsopoulos, Konstantinos E

2014-01-01

This paper investigates quality-driven cross-layer optimization for resource allocation in direct sequence code division multiple access wireless visual sensor networks. We consider a single-hop network topology, where each sensor transmits directly to a centralized control unit (CCU) that manages the available network resources. Our aim is to enable the CCU to jointly allocate the transmission power and source-channel coding rates for each node, under four different quality-driven criteria that take into consideration the varying motion characteristics of each recorded video. For this purpose, we studied two approaches with a different tradeoff of quality and complexity. The first one allocates the resources individually for each sensor, whereas the second clusters them according to the recorded level of motion. In order to address the dynamic nature of the recorded scenery and re-allocate the resources whenever it is dictated by the changes in the amount of motion in the scenery, we propose a mechanism based on the particle swarm optimization algorithm, combined with two restarting schemes that either exploit the previously determined resource allocation or conduct a rough estimation of it. Experimental simulations demonstrate the efficiency of the proposed approaches.

Wireless Power Transfer for Distributed Estimation in Sensor Networks

NASA Astrophysics Data System (ADS)

Mai, Vien V.; Shin, Won-Yong; Ishibashi, Koji

2017-04-01

This paper studies power allocation for distributed estimation of an unknown scalar random source in sensor networks with a multiple-antenna fusion center (FC), where wireless sensors are equipped with radio-frequency based energy harvesting technology. The sensors' observation is locally processed by using an uncoded amplify-and-forward scheme. The processed signals are then sent to the FC, and are coherently combined at the FC, at which the best linear unbiased estimator (BLUE) is adopted for reliable estimation. We aim to solve the following two power allocation problems: 1) minimizing distortion under various power constraints; and 2) minimizing total transmit power under distortion constraints, where the distortion is measured in terms of mean-squared error of the BLUE. Two iterative algorithms are developed to solve the non-convex problems, which converge at least to a local optimum. In particular, the above algorithms are designed to jointly optimize the amplification coefficients, energy beamforming, and receive filtering. For each problem, a suboptimal design, a single-antenna FC scenario, and a common harvester deployment for colocated sensors, are also studied. Using the powerful semidefinite relaxation framework, our result is shown to be valid for any number of sensors, each with different noise power, and for an arbitrarily number of antennas at the FC.

Optimal Pricing and Power Allocation for Collaborative Jamming with Full Channel Knowledge in Wireless Sensor Networks

PubMed Central

Jeong, Dae-Kyo; Kim, Insook; Kim, Dongwoo

2017-01-01

This paper presents a price-searching model in which a source node (Alice) seeks friendly jammers that prevent eavesdroppers (Eves) from snooping legitimate communications by generating interference or noise. Unlike existing models, the distributed jammers also have data to send to their respective destinations and are allowed to access Alice’s channel if it can transmit sufficient jamming power, which is referred to as collaborative jamming in this paper. For the power used to deliver its own signal, the jammer should pay Alice. The price of the jammers’ signal power is set by Alice and provides a tradeoff between the signal and the jamming power. This paper presents, in closed-form, an optimal price that maximizes Alice’s benefit and the corresponding optimal power allocation from a jammers’ perspective by assuming that the network-wide channel knowledge is shared by Alice and jammers. For a multiple-jammer scenario where Alice hardly has the channel knowledge, this paper provides a distributed and interactive price-searching procedure that geometrically converges to an optimal price and shows that Alice by a greedy selection policy achieves certain diversity gain, which increases log-linearly as the number of (potential) jammers grows. Various numerical examples are presented to illustrate the behavior of the proposed model. PMID:29165373

Optimal Pricing and Power Allocation for Collaborative Jamming with Full Channel Knowledge in Wireless Sensor Networks.

PubMed

Jeong, Dae-Kyo; Kim, Insook; Kim, Dongwoo

2017-11-22

This paper presents a price-searching model in which a source node (Alice) seeks friendly jammers that prevent eavesdroppers (Eves) from snooping legitimate communications by generating interference or noise. Unlike existing models, the distributed jammers also have data to send to their respective destinations and are allowed to access Alice's channel if it can transmit sufficient jamming power, which is referred to as collaborative jamming in this paper. For the power used to deliver its own signal, the jammer should pay Alice. The price of the jammers' signal power is set by Alice and provides a tradeoff between the signal and the jamming power. This paper presents, in closed-form, an optimal price that maximizes Alice's benefit and the corresponding optimal power allocation from a jammers' perspective by assuming that the network-wide channel knowledge is shared by Alice and jammers. For a multiple-jammer scenario where Alice hardly has the channel knowledge, this paper provides a distributed and interactive price-searching procedure that geometrically converges to an optimal price and shows that Alice by a greedy selection policy achieves certain diversity gain, which increases log-linearly as the number of (potential) jammers grows. Various numerical examples are presented to illustrate the behavior of the proposed model.

Distributed Optimization of Multi Beam Directional Communication Networks

DTIC Science & Technology

2017-06-30

kT is the noise figure of the receiver. The path loss from node i to the central station is denoted as fi,C and is similarly defined. We seek to...optimally allocate power among several transmit beams per node in order to maximize the total signal-to- interference noise ratio at the central station...Computing, vol. 15, no. 9, September 2016. [6] X. Quan, Y. Liu, S. Shao, C. Huang, and Y. Tang, “Impacts of Phase Noise on Digital Self-Iinterference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rey, D.; Ryan, W.; Ross, M.

A method for more efficiently utilizing the frequency bandwidth allocated for data transmission is presented. Current space and range communication systems use modulation and coding schemes that transmit 0.5 to 1.0 bits per second per Hertz of radio frequency bandwidth. The goal in this LDRD project is to increase the bandwidth utilization by employing advanced digital communications techniques. This is done with little or no increase in the transmit power which is usually very limited on airborne systems. Teaming with New Mexico State University, an implementation of trellis coded modulation (TCM), a coding and modulation scheme pioneered by Ungerboeck, wasmore » developed for this application and simulated on a computer. TCM provides a means for reliably transmitting data while simultaneously increasing bandwidth efficiency. The penalty is increased receiver complexity. In particular, the trellis decoder requires high-speed, application-specific digital signal processing (DSP) chips. A system solution based on the QualComm Viterbi decoder and the Graychip DSP receiver chips is presented.« less

75 FR 37883 - Transmission Planning and Cost Allocation by Transmission Owning and Operating Public Utilities

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-30

... Planning and Cost Allocation by Transmission Owning and Operating Public Utilities; Proposed Rule #0;#0...] Transmission Planning and Cost Allocation by Transmission Owning and Operating Public Utilities Issued June 17... Transmission Services by Public Utilities; Recovery of Stranded Costs by Public Utilities and Transmitting...

Interference from the Deep Space Network's 70-m High Power Transmitter in Goldstone, CA to 3G Mobile Users Operating in the Surrounding Area

NASA Technical Reports Server (NTRS)

Ho, Christian

2004-01-01

The International Telecommunications Union (ITU) has allocated 2110-2200 MHz for the third generation (3G) mobile services. Part of the spectrum (2110-2120 MHz) is allocated for space research service and has been used by the DSN for years for sending command uplinks to deep space missions. Due to the extremely high power transmitted, potential interference to 3G users in areas surrounding DSN Goldstone exists. To address this issue, a preliminary analytical study has been performed and computer models have been developed. The goal is to provide theoretical foundation and tools to estimate the strength of interference as a function of distance from the transmitter for various interference mechanisms, (or propagation modes), and then determine the size of the area in which 3G users are susceptible to interference from the 400-kW transmitter in Goldstone. The focus is non-line-of-sight interference, taking into account of terrain shielding, anomalous propagation mechanisms, and technical and operational characteristics of the DSN and the 3G services.

Auction-based Security Game for Multiuser Cooperative Networks

NASA Astrophysics Data System (ADS)

Wang, An; Cai, Yueming; Yang, Wendong; Cheng, Yunpeng

2013-04-01

In this paper, we develop an auction-based algorithm to allocate the relay power efficiently to improve the system secrecy rate in a cooperative network, where several source-destination pairs and one cooperative relay are involved. On the one hand, the cooperative relay assists these pairs to transmit under a peak power constraint. On the other hand, the relay is untrusty and is also a passive eavesdropper. The whole auction process is completely distributed and no instantaneous channel state information exchange is needed. We also prove the existence and uniqueness of the Nash Equilibrium (NE) for the proposed power auction game. Moreover, the Pareto optimality is also validated. Simulation results show that our proposed auction-based algorithm can effectively improve the system secrecy rate. Besides, the proposed auction-based algorithm can converge to the unique NE point within a finite number of iterations. More interestingly, we also find that the proposed power auction mechanism is cheat-proof.

Energy Efficiency Maximization for WSNs with Simultaneous Wireless Information and Power Transfer

PubMed Central

Yu, Hongyan; Zhang, Yongqiang; Yang, Yuanyuan; Ji, Luyue

2017-01-01

Recently, the simultaneous wireless information and power transfer (SWIPT) technique has been regarded as a promising approach to enhance performance of wireless sensor networks with limited energy supply. However, from a green communication perspective, energy efficiency optimization for SWIPT system design has not been investigated in Wireless Rechargeable Sensor Networks (WRSNs). In this paper, we consider the tradeoffs between energy efficiency and three factors including spectral efficiency, the transmit power and outage target rate for two different modes, i.e., power splitting (PS) and time switching modes (TS), at the receiver. Moreover, we formulate the energy efficiency maximization problem subject to the constraints of minimum Quality of Service (QoS), minimum harvested energy and maximum transmission power as non-convex optimization problem. In particular, we focus on optimizing power control and power allocation policy in PS and TS modes to maximize energy efficiency of data transmission. For PS and TS modes, we propose the corresponding algorithm to characterize a non-convex optimization problem that takes into account the circuit power consumption and the harvested energy. By exploiting nonlinear fractional programming and Lagrangian dual decomposition, we propose suboptimal iterative algorithms to obtain the solutions of non-convex optimization problems. Furthermore, we derive the outage probability and effective throughput from the scenarios that the transmitter does not or partially know the channel state information (CSI) of the receiver. Simulation results illustrate that the proposed optimal iterative algorithm can achieve optimal solutions within a small number of iterations and various tradeoffs between energy efficiency and spectral efficiency, transmit power and outage target rate, respectively. PMID:28820496

Energy Efficiency Maximization for WSNs with Simultaneous Wireless Information and Power Transfer.

PubMed

Yu, Hongyan; Zhang, Yongqiang; Guo, Songtao; Yang, Yuanyuan; Ji, Luyue

2017-08-18

Recently, the simultaneous wireless information and power transfer (SWIPT) technique has been regarded as a promising approach to enhance performance of wireless sensor networks with limited energy supply. However, from a green communication perspective, energy efficiency optimization for SWIPT system design has not been investigated in Wireless Rechargeable Sensor Networks (WRSNs). In this paper, we consider the tradeoffs between energy efficiency and three factors including spectral efficiency, the transmit power and outage target rate for two different modes, i.e., power splitting (PS) and time switching modes (TS), at the receiver. Moreover, we formulate the energy efficiency maximization problem subject to the constraints of minimum Quality of Service (QoS), minimum harvested energy and maximum transmission power as non-convex optimization problem. In particular, we focus on optimizing power control and power allocation policy in PS and TS modes to maximize energy efficiency of data transmission. For PS and TS modes, we propose the corresponding algorithm to characterize a non-convex optimization problem that takes into account the circuit power consumption and the harvested energy. By exploiting nonlinear fractional programming and Lagrangian dual decomposition, we propose suboptimal iterative algorithms to obtain the solutions of non-convex optimization problems. Furthermore, we derive the outage probability and effective throughput from the scenarios that the transmitter does not or partially know the channel state information (CSI) of the receiver. Simulation results illustrate that the proposed optimal iterative algorithm can achieve optimal solutions within a small number of iterations and various tradeoffs between energy efficiency and spectral efficiency, transmit power and outage target rate, respectively.

Coalition Formation and Spectrum Sharing of Cooperative Spectrum Sensing Participants.

PubMed

Zhensheng Jiang; Wei Yuan; Leung, Henry; Xinge You; Qi Zheng

2017-05-01

In cognitive radio networks, self-interested secondary users (SUs) desire to maximize their own throughput. They compete with each other for transmit time once the absence of primary users (PUs) is detected. To satisfy the requirement of PU protection, on the other hand, they have to form some coalitions and cooperate to conduct spectrum sensing. Such dilemma of SUs between competition and cooperation motivates us to study two interesting issues: 1) how to appropriately form some coalitions for cooperative spectrum sensing (CSS) and 2) how to share transmit time among SUs. We jointly consider these two issues, and propose a noncooperative game model with 2-D strategies. The first dimension determines coalition formation, and the second indicates transmit time allocation. Considering the complexity of solving this game, we decompose the game into two more tractable ones: one deals with the formation of CSS coalitions, and the other focuses on the allocation of transmit time. We characterize the Nash equilibria (NEs) of both games, and show that the combination of these two NEs corresponds to the NE of the original game. We also develop a distributed algorithm to achieve a desirable NE of the original game. When this NE is achieved, the SUs obtain a Dhp-stable coalition structure and a fair transmit time allocation. Numerical results verify our analyses, and demonstrate the effectiveness of our algorithm.

11 CFR 106.2 - State allocation of expenditures incurred by authorized committees of Presidential primary...

Code of Federal Regulations, 2011 CFR

2011-01-01

... expenditures shall be based on consistent data for each State to which an allocation is made. (i) Media... estimated audience. This allocation of expenditures, shall be made using industry market data. If industry market data is not available, the committee shall obtain market data from the media carrier transmitting...

Development of a mobile satellite communication unit

NASA Technical Reports Server (NTRS)

Suzuki, Ryutaro; Ikegami, Tetsushi; Hamamoto, Naokazu; Taguchi, Tetsu; Endo, Nobuhiro; Yamamoto, Osamu; Ichiyoshi, Osamu

1988-01-01

A compact 210(W) x 280(H) x 330(D) mm mobile terminal capable of transmitting voice and data through L-band mobile satellites is described. The Voice Codec can convert an analog voice to or from digital codes at rates of 9.6, 8 and 4.8 kb/s by an MPC algorithm. The terminal functions with a single 12 V power supplied vehicle battery. The equipment can operate at any L-band frequency allocated for mobile uses in a full duplex mode and will soon be put into a field test via Japans's ETS-V satellite.

Large-Scale Multiantenna Multisine Wireless Power Transfer

NASA Astrophysics Data System (ADS)

Huang, Yang; Clerckx, Bruno

2017-11-01

Wireless Power Transfer (WPT) is expected to be a technology reshaping the landscape of low-power applications such as the Internet of Things, Radio Frequency identification (RFID) networks, etc. Although there has been some progress towards multi-antenna multi-sine WPT design, the large-scale design of WPT, reminiscent of massive MIMO in communications, remains an open challenge. In this paper, we derive efficient multiuser algorithms based on a generalizable optimization framework, in order to design transmit sinewaves that maximize the weighted-sum/minimum rectenna output DC voltage. The study highlights the significant effect of the nonlinearity introduced by the rectification process on the design of waveforms in multiuser systems. Interestingly, in the single-user case, the optimal spatial domain beamforming, obtained prior to the frequency domain power allocation optimization, turns out to be Maximum Ratio Transmission (MRT). In contrast, in the general weighted sum criterion maximization problem, the spatial domain beamforming optimization and the frequency domain power allocation optimization are coupled. Assuming channel hardening, low-complexity algorithms are proposed based on asymptotic analysis, to maximize the two criteria. The structure of the asymptotically optimal spatial domain precoder can be found prior to the optimization. The performance of the proposed algorithms is evaluated. Numerical results confirm the inefficiency of the linear model-based design for the single and multi-user scenarios. It is also shown that as nonlinear model-based designs, the proposed algorithms can benefit from an increasing number of sinewaves.

Patch Network for Power Allocation and Distribution in Smart Materials

NASA Technical Reports Server (NTRS)

Golembiewski, Walter T.

2000-01-01

The power allocation and distribution (PAD) circuitry is capable of allocating and distributing a single or multiple sources of power over multi-elements of a power user grid system. The purpose of this invention is to allocate and distribute power that is collected by individual patch rectennas to a region of specific power-user devices, such as actuators. The patch rectenna converts microwave power into DC power. Then this DC power is used to drive actuator devices. However, the power from patch rectennas is not sufficient to drive actuators unless all the collected power is effectively used to drive another group by allocation and distribution. The power allocation and distribution (PAD) circuitry solves the shortfall of power for devices in a large array. The PAD concept is based on the networked power control in which power collected over the whole array of rectennas is allocated to a sub domain where a group of devices is required to be activated for operation. Then the allocated power is distributed to individual element of power-devices in the sub domain according to a selected run-mode.

76 FR 45551 - Post-2014 Resource Pool; Loveland Area Projects, Proposed Power Allocation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

... Proposed Power Allocation. SUMMARY: Western Area Power Administration (Western), a Federal power marketing... Pool Proposed Power Allocation developed under the requirements of the Power Marketing Initiative of Western's Energy Planning and Management Program (Program). Western notified the public of allocation...

Dynamic advance reservation with delayed allocation

DOEpatents

Vokkarane, Vinod; Somani, Arun

2014-12-02

A method of scheduling data transmissions from a source to a destination, includes the steps of: providing a communication system having a number of channels and a number of paths, each of the channels having a plurality of designated time slots; receiving two or more data transmission requests; provisioning the transmission of the data; receiving data corresponding to at least one of the two or more data transmission requests; waiting until an earliest requested start time T.sub.s; allocating at the current time each of the two or more data transmission requests; transmitting the data; and repeating the steps of waiting, allocating, and transmitting until each of the two or more data transmission requests that have been provisioned for a transmission of data is satisfied. A system to perform the method of scheduling data transmissions is also described.

A Subcarrier-Pair Based Resource Allocation Scheme Using Proportional Fairness for Cooperative OFDM-Based Cognitive Radio Networks

PubMed Central

Ma, Yongtao; Zhou, Liuji; Liu, Kaihua

2013-01-01

The paper presents a joint subcarrier-pair based resource allocation algorithm in order to improve the efficiency and fairness of cooperative multiuser orthogonal frequency division multiplexing (MU-OFDM) cognitive radio (CR) systems. A communication model where one source node communicates with one destination node assisted by one half-duplex decode-and-forward (DF) relay is considered in the paper. An interference-limited environment is considered, with the constraint of transmitted sum-power over all channels and aggregate average interference towards multiple primary users (PUs). The proposed resource allocation algorithm is capable of maximizing both the system transmission efficiency and fairness among secondary users (SUs). Besides, the proposed algorithm can also keep the interference introduced to the PU bands below a threshold. A proportional fairness constraint is used to assure that each SU can achieve a required data rate, with quality of service guarantees. Moreover, we extend the analysis to the scenario where each cooperative SU has no channel state information (CSI) about non-adjacent links. We analyzed the throughput and fairness tradeoff in CR system. A detailed analysis of the performance of the proposed algorithm is presented with the simulation results. PMID:23939586

47 CFR 95.135 - Maximum authorized transmitting power.

Code of Federal Regulations, 2010 CFR

2010-10-01

... transmitting power. (a) No station may transmit with more than 50 watts output power. (b) [Reserved] (c) A small control station at a point north of Line A or east of Line C must transmit with no more than 5 watts ERP. (d) A fixed station must transmit with no more than 15 watts output power. (e) A small base...

77 FR 5406 - Amateur Radio Use of the Allocation at 5 MHz

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-03

... transmit emission types in addition to those proposed in the NPRM? (3) Would a Voice-Operated Transmit (VOX... carrier frequency is set to the center frequency. 22. VOX Requirement. The Commission requested comment on whether amateur operators should be required to use VOX in the phone emission mode, which ARRL stated...

GNSS satellite transmit power and its impact on orbit determination

NASA Astrophysics Data System (ADS)

Steigenberger, Peter; Thoelert, Steffen; Montenbruck, Oliver

2018-06-01

Antenna thrust is a small acceleration acting on Global Navigation Satellite System satellites caused by the transmission of radio navigation signals. Knowledge about the transmit power and the mass of the satellites is required for the computation of this effect. The actual transmit power can be obtained from measurements with a high-gain antenna and knowledge about the properties of the transmit and receive antennas as well as losses along the propagation path. Transmit power measurements for different types of GPS, GLONASS, Galileo, and BeiDou-2 satellites were taken with a 30-m dish antenna of the German Aerospace Center (DLR) located at its ground station in Weilheim. For GPS, total L-band transmit power levels of 50-240 W were obtained, 20-135 W for GLONASS, 95-265 W for Galileo, and 130-185 W for BeiDou-2. The transmit power differs usually only slightly for individual spacecraft within one satellite block. An exception are the GLONASS-M satellites where six subgroups with different transmit power levels could be identified. Considering the antenna thrust in precise orbit determination of GNSS satellites decreases the orbital radius by 1-27 mm depending on the transmit power, the satellite mass, and the orbital period.

76 FR 64085 - Post-2014 Resource Pool-Loveland Area Projects, Final Power Allocation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... power allocation. SUMMARY: The Western Area Power Administration (Western), a Federal power marketing..., Final Power Allocation developed under the requirements of subpart C-Power Marketing Initiative of the Energy Planning and Management Program (Program) Final Rule, 10 CFR part 905. These final power...

Space transportation alternatives for large space programs - The International Space University summer session - 1992

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan

1993-01-01

The issues discussed in this paper are the result of a 10-week study by the Space Solar Power Program design project members and the Space Transportation Group at the International Space University (ISU) summer session of 1992 to investigate new paradigms in space propulsion and how those paradigms might reduce the costs for large space programs. The program plan was to place a series of power satellites in Earth orbit. Several designs were studied where many kW, MW or GW of power would be transmitted to Earth or to other spacecraft in orbit. During the summer session, a space solar power system was also detailed and analyzed. At ISU, the focus of the study was to foster and develop some of the new paradigms that may eliminate the barriers to low cost for space exploration and exploitation. Many international and technical aspects of a large multinational program were studied. Environmental safety, space construction and maintenance, legal and policy issues of frequency allocation, technology transfer and control and many other areas were addressed.

System for a displaying at a remote station data generated at a central station and for powering the remote station from the central station

NASA Technical Reports Server (NTRS)

Perry, J. C. (Inventor)

1980-01-01

A system for displaying at a remote station data generated at a central station and for powering the remote station from the central station is presented. A power signal is generated at the central station and time multiplexed with the data and then transmitted to the remote station. An energy storage device at the remote station is responsive to the transmitted power signal to provide energizing power for the circuits at the remote station during the time interval data is being transmitted to the remote station. Energizing power for the circuits at the remote station is provided by the power signal itself during the time this signal is transmitted. Preferably the energy storage device is a capacitor which is charged by the power signal during the time the power is transmitted and is slightly discharged during the time the data is transmitted to energize the circuits at the remote station.

Does Funding for HIV and Sexually Transmitted Disease Prevention Matter? Evidence from Panel Data

ERIC Educational Resources Information Center

Chesson, Harrell W.; Harrison, Paul; Scotton, Carol R.; Varghese, Beena

2005-01-01

Since the onset of the AIDS epidemic, the Centers for Disease Control and Prevention (CDC) has allocated several billion dollars for the prevention of HIV and other sexually transmitted diseases (STDs) in the United States. Using state-level data from 1981 to 1998, the authors found that greater amounts of prevention funding in a given year are…

47 CFR 22.809 - Transmitting power limits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transmitting power limits. The transmitting power of ground and airborne mobile transmitters operating on the... Watts, except as provided in § 22.811. (b) Airborne mobile transmitters. The transmitter power output of airborne mobile transmitters must not exceed 25 Watts and must not be less than 4 Watts. ...

Predicting the epidemiological impact of antiretroviral allocation strategies in KwaZulu-Natal: the effect of the urban-rural divide.

PubMed

Wilson, David P; Kahn, James; Blower, Sally M

2006-09-19

Antiretroviral therapy (ART) is becoming available in South Africa. Demand will exceed supply; thus, difficult decisions will have to be made in allocating ART. The majority of those treated for HIV are likely to be in cities, because health infrastructure and personnel are concentrated in urban centers. We predict the epidemiological impact of drug allocation strategies (DAS) by using a spatially explicit model that links urban and rural epidemics. We parameterize our model by using data from the KwaZulu-Natal province in South Africa. We model the South African government's treatment plan from 2004-2008, and we predict the consequences of one DAS that allocates drugs only to Durban and of two DAS that allocate drugs to both urban and rural areas. All three strategies would treat 500,000 people by 2008. Not surprisingly, the Durban-only DAS would prevent the greatest number of infections (an additional 15,000 infections by 2008). However, it may have been expected that this DAS would generate the highest levels of transmitted resistance, because it concentrates ART in one location. Paradoxically, we found that this DAS would generate the lowest levels of transmitted resistance. Concentrating treatment in Durban would also avert the greatest number of AIDS-related deaths. We discuss the difference between using the principle of treatment equity versus using the principle of utilitarianism/efficiency to allocate ART. Decisions about allocating scarce drugs should consider treatment equity as well as epidemiological consequences. Notably, a Durban-only DAS would lead to new disparities in healthcare between urban and rural areas in KwaZulu-Natal.

Microwave power transmission system wherein level of transmitted power is controlled by reflections from receiver

NASA Technical Reports Server (NTRS)

Robinson, W. J., Jr. (Inventor)

1974-01-01

A microwave, wireless, power transmission system is described in which the transmitted power level is adjusted to correspond with power required at a remote receiving station. Deviations in power load produce an antenna impedance mismatch causing variations in energy reflected by the power receiving antenna employed by the receiving station. The variations in reflected energy are sensed by a receiving antenna at the transmitting station and used to control the output power of a power transmitter.

Space-Time Processing for Tactical Mobile Ad Hoc Networks

DTIC Science & Technology

2007-08-01

rates in mobile ad hoc networks. In addition, he has considered the design of a cross-layer multi-user resource allocation framework using a... framework for many-to-one communication. In this context, multiple nodes cooperate to transmit their packets simultaneously to a single node using multi...spatially multiplexed signals transmitted from multiple nodes. Our goal is to form a framework that activates different sets of communication links

Power Allocation and Outage Probability Analysis for SDN-based Radio Access Networks

NASA Astrophysics Data System (ADS)

Zhao, Yongxu; Chen, Yueyun; Mai, Zhiyuan

2018-01-01

In this paper, performance of Access network Architecture based SDN (Software Defined Network) is analyzed with respect to the power allocation issue. A power allocation scheme PSO-PA (Particle Swarm Optimization-power allocation) algorithm is proposed, the proposed scheme is subjected to constant total power with the objective of minimizing system outage probability. The entire access network resource configuration is controlled by the SDN controller, then it sends the optimized power distribution factor to the base station source node (SN) and the relay node (RN). Simulation results show that the proposed scheme reduces the system outage probability at a low complexity.

46 CFR 111.79-9 - Transmitting power between receptacles.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Transmitting power between receptacles. 111.79-9 Section 111.79-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Receptacles § 111.79-9 Transmitting power between receptacles. (a) If...

46 CFR 111.79-9 - Transmitting power between receptacles.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Transmitting power between receptacles. 111.79-9 Section 111.79-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Receptacles § 111.79-9 Transmitting power between receptacles. (a) If...

46 CFR 111.79-9 - Transmitting power between receptacles.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Transmitting power between receptacles. 111.79-9 Section 111.79-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Receptacles § 111.79-9 Transmitting power between receptacles. (a) If...

46 CFR 111.79-9 - Transmitting power between receptacles.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Transmitting power between receptacles. 111.79-9 Section 111.79-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Receptacles § 111.79-9 Transmitting power between receptacles. (a) If...

46 CFR 111.79-9 - Transmitting power between receptacles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Transmitting power between receptacles. 111.79-9 Section 111.79-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Receptacles § 111.79-9 Transmitting power between receptacles. (a) If...

47 CFR 97.313 - Transmitter power standards.

Code of Federal Regulations, 2010 CFR

2010-10-01

... station may transmit with a transmitter power exceeding 1.5 kW PEP. (c) No station may transmit with a transmitter power output exceeding 200 W PEP: (1) On the 10.10-10.15 MHz segment; (2) On the 3.525-3.60 MHz, 7... within ITU Regions 1 or 3. (d) No station may transmit with a transmitter power exceeding 25 W PEP on the...

47 CFR 97.313 - Transmitter power standards.

Code of Federal Regulations, 2013 CFR

2013-10-01

... station may transmit with a transmitter power exceeding 1.5 kW PEP. (c) No station may transmit with a transmitter power output exceeding 200 W PEP: (1) On the 10.10-10.15 MHz segment; (2) On the 3.525-3.60 MHz, 7... Regions 1 or 3. (d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m...

47 CFR 97.313 - Transmitter power standards.

Code of Federal Regulations, 2014 CFR

2014-10-01

... station may transmit with a transmitter power exceeding 1.5 kW PEP. (c) No station may transmit with a transmitter power output exceeding 200 W PEP: (1) On the 10.10-10.15 MHz segment; (2) On the 3.525-3.60 MHz, 7... Regions 1 or 3. (d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m...

47 CFR 97.313 - Transmitter power standards.

Code of Federal Regulations, 2011 CFR

2011-10-01

... station may transmit with a transmitter power exceeding 1.5 kW PEP. (c) No station may transmit with a transmitter power output exceeding 200 W PEP: (1) On the 10.10-10.15 MHz segment; (2) On the 3.525-3.60 MHz, 7... Regions 1 or 3. (d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m...

47 CFR 97.313 - Transmitter power standards.

Code of Federal Regulations, 2012 CFR

2012-10-01

... station may transmit with a transmitter power exceeding 1.5 kW PEP. (c) No station may transmit with a transmitter power output exceeding 200 W PEP: (1) On the 10.10-10.15 MHz segment; (2) On the 3.525-3.60 MHz, 7... Regions 1 or 3. (d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m...

Multiple beam antenna/switch system study

NASA Technical Reports Server (NTRS)

1989-01-01

In the study of the Multiple Beam Antenna/Switch for the space to ground link (SGL) uplink and downlink services, several issues related to system engineering, antenna, transmit/receive, and switch systems were addressed and the results are provided. Bandwidth allocation at Ku band is inadequate to serve the data rate requirements for the forward and return services. Rain and depolarization effects at EHF, especially at Ka band, pose a significant threat to the link availabilities at heavy rain areas. Hardware induced effects such as the nonlinear characteristics of the power amplifier may necessitate the use of linearizers and limiters. It is also important to identify the components that are susceptible to the space radiation effects and shield or redesign them with rad-hard technologies for meeting the requirements of the space environment.

10 CFR Appendix D to Subpart D of... - Classes of Actions that Normally Require EISs

Code of Federal Regulations, 2012 CFR

2012-01-01

...] D7Contracts, policies, and marketing and allocation plans for electric power D8Import or export of natural gas... and Allocation Plans for Electric Power Establishment and implementation of contracts, policies, and marketing and allocation plans related to electric power acquisition that involve (1) The interconnection of...

10 CFR Appendix D to Subpart D of... - Classes of Actions that Normally Require EISs

Code of Federal Regulations, 2013 CFR

2013-01-01

...] D7Contracts, policies, and marketing and allocation plans for electric power D8Import or export of natural gas... and Allocation Plans for Electric Power Establishment and implementation of contracts, policies, and marketing and allocation plans related to electric power acquisition that involve (1) The interconnection of...

Market power in auction and efficiency in emission permits allocation.

PubMed

Jiang, Min Xing; Yang, Dong Xiao; Chen, Zi Yue; Nie, Pu Yan

2016-12-01

This paper analyzes how to achieve the cost-effectiveness by initial allocation of CO 2 emission permits when a single dominant firm in production market has market power in auction, and compare two prevalent allocation patterns, mixed allocation and single auction. We show how the firm with market power may manipulate the auction price, thereby this leads to fail to achieve cost-effective solution by auction unless the total permits for allocation equal to the effective emissions cap. Provided that the market power firm receives strictly positive free permits, the effective emissions cap of mixed allocation is larger than that of single auction. The production market share of dominant firm is increasing with the free permits it holds. Finally, we examine the compliance costs and welfare of mixed allocation and single auction, the result show that the former is preferred to the later when policy makers consider economic welfare without welfare cost due to CO 2 emissions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Real-Time and Secure Wireless Health Monitoring

PubMed Central

Dağtaş, S.; Pekhteryev, G.; Şahinoğlu, Z.; Çam, H.; Challa, N.

2008-01-01

We present a framework for a wireless health monitoring system using wireless networks such as ZigBee. Vital signals are collected and processed using a 3-tiered architecture. The first stage is the mobile device carried on the body that runs a number of wired and wireless probes. This device is also designed to perform some basic processing such as the heart rate and fatal failure detection. At the second stage, further processing is performed by a local server using the raw data transmitted by the mobile device continuously. The raw data is also stored at this server. The processed data as well as the analysis results are then transmitted to the service provider center for diagnostic reviews as well as storage. The main advantages of the proposed framework are (1) the ability to detect signals wirelessly within a body sensor network (BSN), (2) low-power and reliable data transmission through ZigBee network nodes, (3) secure transmission of medical data over BSN, (4) efficient channel allocation for medical data transmission over wireless networks, and (5) optimized analysis of data using an adaptive architecture that maximizes the utility of processing and computational capacity at each platform. PMID:18497866

Adaptive limited feedback for interference alignment in MIMO interference channels.

PubMed

Zhang, Yang; Zhao, Chenglin; Meng, Juan; Li, Shibao; Li, Li

2016-01-01

It is very important that the radar sensor network has autonomous capabilities such as self-managing, etc. Quite often, MIMO interference channels are applied to radar sensor networks, and for self-managing purpose, interference management in MIMO interference channels is critical. Interference alignment (IA) has the potential to dramatically improve system throughput by effectively mitigating interference in multi-user networks at high signal-to-noise (SNR). However, the implementation of IA predominantly relays on perfect and global channel state information (CSI) at all transceivers. A large amount of CSI has to be fed back to all transmitters, resulting in a proliferation of feedback bits. Thus, IA with limited feedback has been introduced to reduce the sum feedback overhead. In this paper, by exploiting the advantage of heterogeneous path loss, we first investigate the throughput of IA with limited feedback in interference channels while each user transmits multi-streams simultaneously, then we get the upper bound of sum rate in terms of the transmit power and feedback bits. Moreover, we propose a dynamic feedback scheme via bit allocation to reduce the throughput loss due to limited feedback. Simulation results demonstrate that the dynamic feedback scheme achieves better performance in terms of sum rate.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hao, He; Sun, Yannan; Carroll, Thomas E.

We propose a coordination algorithm for cooperative power allocation among a collection of commercial buildings within a campus. We introduced thermal and power models of a typical commercial building Heating, Ventilation, and Air Conditioning (HVAC) system, and utilize model predictive control to characterize their power flexibility. The power allocation problem is formulated as a cooperative game using the Nash Bargaining Solution (NBS) concept, in which buildings collectively maximize the product of their utilities subject to their local flexibility constraints and a total power limit set by the campus coordinator. To solve the optimal allocation problem, a distributed protocol is designedmore » using dual decomposition of the Nash bargaining problem. Numerical simulations are performed to demonstrate the efficacy of our proposed allocation method« less

Radio Frequency Compatibility Evaluation of S Band Navigation Signals for Future BeiDou

PubMed Central

Sun, Yanbo; Xue, Rui; Zhao, Danfeng; Wang, Dun

2017-01-01

With L band frequency allocations for satellite navigation getting more crowded, S band (2483.5–2500 MHz) is already allocated for navigation services, where Globalstar broadcasts downlink communications to user terminals. The Indian Regional Navigation Satellite System (IRNSS) is transmitting navigation signals and Galileo exploits some potential signals in S band. Also, several candidate S band signals based on binary offset carrier (BOC), binary phase shift keying (BPSK), continuous phase modulation (CPM) and minimum shift keying-BOC (MSK-BOC) are suggested for BeiDou system (BDS). In quite narrow S band, mutual interference among these systems is inevitable, thus the compatibility issue is particularly significant for S band signal design. To explore desired S band signals for BDS, the paper firstly describes a comprehensive compatibility evaluation methods based on effective carrier-to-noise ratio degradation for acquisition and code tracking. Then a real simulation is established using space constellations, modulation schemes and received power. Finally, the worst mutual interference of BDS candidate signals with Galileo, IRNSS and Globalstar is calculated and compared. The results indicate that CPM signal is easier to allow peaceful coexistence of other systems with minimal mutual interference in S band compared to other BDS candidates. PMID:28475142

Radio Frequency Compatibility Evaluation of S Band Navigation Signals for Future BeiDou.

PubMed

Sun, Yanbo; Xue, Rui; Zhao, Danfeng; Wang, Dun

2017-05-05

With L band frequency allocations for satellite navigation getting more crowded, S band (2483.5-2500 MHz) is already allocated for navigation services, where Globalstar broadcasts downlink communications to user terminals. The Indian Regional Navigation Satellite System (IRNSS) is transmitting navigation signals and Galileo exploits some potential signals in S band. Also, several candidate S band signals based on binary offset carrier (BOC), binary phase shift keying (BPSK), continuous phase modulation (CPM) and minimum shift keying-BOC (MSK-BOC) are suggested for BeiDou system (BDS). In quite narrow S band, mutual interference among these systems is inevitable, thus the compatibility issue is particularly significant for S band signal design. To explore desired S band signals for BDS, the paper firstly describes a comprehensive compatibility evaluation methods based on effective carrier-to-noise ratio degradation for acquisition and code tracking. Then a real simulation is established using space constellations, modulation schemes and received power. Finally, the worst mutual interference of BDS candidate signals with Galileo, IRNSS and Globalstar is calculated and compared. The results indicate that CPM signal is easier to allow peaceful coexistence of other systems with minimal mutual interference in S band compared to other BDS candidates.

47 CFR 25.204 - Power limits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... communication services, the equivalent isotropically radiated power transmitted in any direction towards the... coequally with terrestrial radiocommunication services, the equivalent isotropically radiated power... restriction as to the equivalent isotropically radiated power transmitted by an earth station towards the...

47 CFR 25.204 - Power limits.

Code of Federal Regulations, 2012 CFR

2012-10-01

... communication services, the equivalent isotropically radiated power transmitted in any direction towards the... coequally with terrestrial radiocommunication services, the equivalent isotropically radiated power... restriction as to the equivalent isotropically radiated power transmitted by an earth station towards the...

47 CFR 25.204 - Power limits.

Code of Federal Regulations, 2011 CFR

2011-10-01

... communication services, the equivalent isotropically radiated power transmitted in any direction towards the... coequally with terrestrial radiocommunication services, the equivalent isotropically radiated power... restriction as to the equivalent isotropically radiated power transmitted by an earth station towards the...

Sex allocation conflict in insect societies: who wins?

PubMed Central

Helanterä, Heikki; Ratnieks, Francis L. W.

2009-01-01

Sex allocation in colonies of eusocial Hymenoptera is one of the best studied social conflicts. We outline a framework for analysing conflict outcome through power and the costs of manipulation and suggest that the conflict will often be unresolved because both major parties of interest, the queen and the workers, should manipulate allocation even at considerable costs to the colony. We suggest future work for analysing power in the conflict between queen and workers over sex allocation and discuss the extent of male power. PMID:19656859

An Accurate Transmitting Power Control Method in Wireless Communication Transceivers

NASA Astrophysics Data System (ADS)

Zhang, Naikang; Wen, Zhiping; Hou, Xunping; Bi, Bo

2018-01-01

Power control circuits are widely used in transceivers aiming at stabilizing the transmitted signal power to a specified value, thereby reducing power consumption and interference to other frequency bands. In order to overcome the shortcomings of traditional modes of power control, this paper proposes an accurate signal power detection method by multiplexing the receiver and realizes transmitting power control in the digital domain. The simulation results show that this novel digital power control approach has advantages of small delay, high precision and simplified design procedure. The proposed method is applicable to transceivers working at large frequency dynamic range, and has good engineering practicability.

Power balance and loss mechanism analysis in RF transmit coil arrays.

PubMed

Kuehne, Andre; Goluch, Sigrun; Waxmann, Patrick; Seifert, Frank; Ittermann, Bernd; Moser, Ewald; Laistler, Elmar

2015-10-01

To establish a framework for transmit array power balance calculations based on power correlation matrices to accurately quantify the loss contributions from different mechanisms such as coupling, lumped components, and radiation. Starting from Poynting's theorem, power correlation matrices are derived for all terms in the power balance, which is formulated as a matrix equation. Finite-difference time-domain simulations of two 7 T eight-channel head array coils at 297.2 MHz are used to verify the theoretical considerations and demonstrate their application. Care is taken to accurately incorporate all loss mechanisms. The power balance for static B1 phase shims as well as two-dimensional spatially selective transmit SENSE pulses is shown. The simulated power balance shows an excellent agreement with theory, with a maximum power imbalance of less than 0.11%. Power loss contributions from the different loss mechanisms vary significantly between the investigated setups, and depending on the excitation mode imposed on the coil. The presented approach enables a straightforward loss evaluation for an arbitrary excitation of transmit coil arrays. Worst-case power imbalance and losses are calculated in a straightforward manner. This allows for deeper insight into transmit array loss mechanisms, incorporation of radiated power components in specific absorption rate calculations and verification of electromagnetic simulations. © 2014 Wiley Periodicals, Inc.

STARSYS: A view after WARC-92

NASA Astrophysics Data System (ADS)

Kaveeshwar, Ashok; Rodriguez, Raul

1993-01-01

The STARSYS system is aimed at providing low cost global positioning and messaging by satellite. STARSYS is a data only system using very brief message transmission times. Code Division Multiple Access (CDMA) is used for frequency sharing; it enables transmitted data to be coded for unique user identification and also to employ Doppler and radio ranging to determine the geographical location of a transmitting terminal. The STARSYS system is composed of the field receiver/transmitter, the Low Earth Orbit (LEO) satellite constellation and the ground station elements. Each message transmission is able to contain up to thirty two digital characters. Market applications are numerous: theft control, vehicle and logistic tracking and messaging, personal communications, utility and environmental data acquisition and transfer. Co-primary frequency allocation at WARC-92 accelerated interest for potential customers and investors, although the amount of frequency allocation (less than 1 GHz) is small.

Power allocation and range performance considerations for a dual-frequency EBPSK/MPPSK system

NASA Astrophysics Data System (ADS)

Yao, Yu; Wu, Lenan; Zhao, Junhui

2017-12-01

Extended binary phase shift keying/M-ary position phase shift keying (EBPSK/MPPSK)-MODEM provides radar and communication functions on a single hardware platform with a single waveform. However, its range estimation accuracy is worse than continuous-wave (CW) radar because of the imbalance of power in two carrier frequencies. In this article, the power allocation method for dual-frequency EBPSK/MPPSK modulated systems is presented. The power of two signal transmitters is adequately allocated to ensure that the power in two carrier frequencies is equal. The power allocation ratios for two types of modulation systems are obtained. Moreover, considerations regarding the range of operation of the dual-frequency system are analysed. In addition to theoretical considerations, computer simulations are provided to illustrate the performance.

Allocation of Transaction Cost to Market Participants Using an Analytical Method in Deregulated Market

NASA Astrophysics Data System (ADS)

Jeyasankari, S.; Jeslin Drusila Nesamalar, J.; Charles Raja, S.; Venkatesh, P.

2014-04-01

Transmission cost allocation is one of the major challenges in transmission open access faced by the electric power sector. The purpose of this work is to provide an analytical method for allocating transmission transaction cost in deregulated market. This research work provides a usage based transaction cost allocation method based on line-flow impact factor (LIF) which relates the power flow in each line with respect to transacted power for the given transaction. This method provides the impact of line flows without running iterative power flow solution and is well suited for real time applications. The proposed method is compared with the Newton-Raphson (NR) method of cost allocation on sample six bus and practical Indian utility 69 bus systems by considering multilateral transaction.

Multimedia transmission in MC-CDMA using adaptive subcarrier power allocation and CFO compensation

NASA Astrophysics Data System (ADS)

Chitra, S.; Kumaratharan, N.

2018-02-01

Multicarrier code division multiple access (MC-CDMA) system is one of the most effective techniques in fourth-generation (4G) wireless technology, due to its high data rate, high spectral efficiency and resistance to multipath fading. However, MC-CDMA systems are greatly deteriorated by carrier frequency offset (CFO) which is due to Doppler shift and oscillator instabilities. It leads to loss of orthogonality among the subcarriers and causes intercarrier interference (ICI). Water filling algorithm (WFA) is an efficient resource allocation algorithm to solve the power utilisation problems among the subcarriers in time-dispersive channels. The conventional WFA fails to consider the effect of CFO. To perform subcarrier power allocation with reduced CFO and to improve the capacity of MC-CDMA system, residual CFO compensated adaptive subcarrier power allocation algorithm is proposed in this paper. The proposed technique allocates power only to subcarriers with high channel to noise power ratio. The performance of the proposed method is evaluated using random binary data and image as source inputs. Simulation results depict that the bit error rate performance and ICI reduction capability of the proposed modified WFA offered superior performance in both power allocation and image compression for high-quality multimedia transmission in the presence of CFO and imperfect channel state information conditions.

47 CFR 95.135 - Maximum authorized transmitting power.

Code of Federal Regulations, 2011 CFR

2011-10-01

... watts ERP. (d) A fixed station must transmit with no more than 15 watts output power. (e) A small base station must transmit with no more than 5 watts ERP. [48 FR 35237, Aug. 3, 1983, as amended at 53 FR 47717...

Rate Adaptive Based Resource Allocation with Proportional Fairness Constraints in OFDMA Systems

PubMed Central

Yin, Zhendong; Zhuang, Shufeng; Wu, Zhilu; Ma, Bo

2015-01-01

Orthogonal frequency division multiple access (OFDMA), which is widely used in the wireless sensor networks, allows different users to obtain different subcarriers according to their subchannel gains. Therefore, how to assign subcarriers and power to different users to achieve a high system sum rate is an important research area in OFDMA systems. In this paper, the focus of study is on the rate adaptive (RA) based resource allocation with proportional fairness constraints. Since the resource allocation is a NP-hard and non-convex optimization problem, a new efficient resource allocation algorithm ACO-SPA is proposed, which combines ant colony optimization (ACO) and suboptimal power allocation (SPA). To reduce the computational complexity, the optimization problem of resource allocation in OFDMA systems is separated into two steps. For the first one, the ant colony optimization algorithm is performed to solve the subcarrier allocation. Then, the suboptimal power allocation algorithm is developed with strict proportional fairness, and the algorithm is based on the principle that the sums of power and the reciprocal of channel-to-noise ratio for each user in different subchannels are equal. To support it, plenty of simulation results are presented. In contrast with root-finding and linear methods, the proposed method provides better performance in solving the proportional resource allocation problem in OFDMA systems. PMID:26426016

Statistical Power and Optimum Sample Allocation Ratio for Treatment and Control Having Unequal Costs Per Unit of Randomization

ERIC Educational Resources Information Center

Liu, Xiaofeng

2003-01-01

This article considers optimal sample allocation between the treatment and control condition in multilevel designs when the costs per sampling unit vary due to treatment assignment. Optimal unequal allocation may reduce the cost from that of a balanced design without sacrificing any power. The optimum sample allocation ratio depends only on the…

75 FR 6369 - Application To Export Electric Energy; Aquilon Power Ltd.

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... DEPARTMENT OF ENERGY [OE Docket No. EA-361] Application To Export Electric Energy; Aquilon Power.... SUMMARY: Aquilon Power Ltd. (Aquilon Power) has applied for authority to transmit electric energy from the... received an application from Aquilon Power for authority to transmit electric energy from the United States...

77 FR 39689 - Application To Export Electric Energy; Dynasty Power, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-05

... DEPARTMENT OF ENERGY [OE Docket No. EA-385] Application To Export Electric Energy; Dynasty Power.... SUMMARY: Dynasty Power, Inc. (Dynasty Power) has applied for authority to transmit electric energy from... an application from Dynasty Power for authority to transmit electric energy from the United States to...

SU-E-I-71: KVp Dependence of Transmitted Exposure for a Radiography Unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, Y; Lynch, D; So, J

2014-06-01

Purpose: To investigate the kVp dependence of the transmitted exposure for a radiography x-ray unit. Methods: The study used a GE DiscoveryTM XR656 DR unit, a 30 (L) × 30 (W) × 25 cm thick Lucite phantom, two anthropomorphic phantoms (an Alderson RS-310 chest phantom and a 3M skull phantom), an Unfors detector, and a Radcal 10x9-6 ion chamber. We measured the entrance exposure and transmitted exposure of each phantom at 60, 70, 80, 90, 100, 110, 120 kVp for mAs range from 2.5 to 200 mAs, without any additional filter. The FOV is 30×30 cm for the Lucite andmore » chest phantom (AP view), and 20×20 cm for skull phantom (Lateral view). The transmitted exposure was measured at the phantom center of the x-ray exit side. For chest phantom, the transmitted exposures at 3 inch upper right and upper left from the center were also measured. We also checked the reproducibility and accuracy of the DR unit. Results: For each phantom, at every kVp and mAs setting, the transmitted exposure per mAs was calculated and normalized by the relative entrance exposure; the averaged transmitted exposure per mAs at each specific kVp was then determined. For chest phantom, the mean transmitted exposure per mAs was the average of three exit locations. The averaged transmitted exposure per mAs was fit as a power function of kVp. The result showed the transmitted exposure per mAs was approximately proportional to third power of the kVp for two anthropomorphic phantoms and forth power of the kVp for the Lucite phantom. Conclusion: The traditional assumption of fifth power kVp dependence to the transmitted exposure is inaccurate. At the normal radiography kVp range, the transmitted exposure is approximately proportional to third power of the kVp for a typical patient and up to forth power of the kVp for a large patient.« less

Analytical Model and Optimized Design of Power Transmitting Coil for Inductively Coupled Endoscope Robot.

PubMed

Ke, Quan; Luo, Weijie; Yan, Guozheng; Yang, Kai

2016-04-01

A wireless power transfer system based on the weakly inductive coupling makes it possible to provide the endoscope microrobot (EMR) with infinite power. To facilitate the patients' inspection with the EMR system, the diameter of the transmitting coil is enlarged to 69 cm. Due to the large transmitting range, a high quality factor of the Litz-wire transmitting coil is a necessity to ensure the intensity of magnetic field generated efficiently. Thus, this paper builds an analytical model of the transmitting coil, and then, optimizes the parameters of the coil by enlarging the quality factor. The lumped model of the transmitting coil includes three parameters: ac resistance, self-inductance, and stray capacitance. Based on the exact two-dimension solution, the accurate analytical expression of ac resistance is derived. Several transmitting coils of different specifications are utilized to verify this analytical expression, being in good agreements with the measured results except the coils with a large number of strands. Then, the quality factor of transmitting coils can be well predicted with the available analytical expressions of self- inductance and stray capacitance. Owing to the exact estimation of quality factor, the appropriate coil turns of the transmitting coil is set to 18-40 within the restrictions of transmitting circuit and human tissue issues. To supply enough energy for the next generation of the EMR equipped with a Ø9.5×10.1 mm receiving coil, the coil turns of the transmitting coil is optimally set to 28, which can transfer a maximum power of 750 mW with the remarkable delivering efficiency of 3.55%.

47 CFR 2.801 - Radiofrequency device defined.

Code of Federal Regulations, 2011 CFR

2011-10-01

....801 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2.801 Radiofrequency device..., but are not limited to: (a) The various types of radio communication transmitting devices described...

Efficient and equitable spatial allocation of renewable power plants at the country scale

NASA Astrophysics Data System (ADS)

Drechsler, Martin; Egerer, Jonas; Lange, Martin; Masurowski, Frank; Meyerhoff, Jürgen; Oehlmann, Malte

2017-09-01

Globally, the production of renewable energy is undergoing rapid growth. One of the most pressing issues is the appropriate allocation of renewable power plants, as the question of where to produce renewable electricity is highly controversial. Here we explore this issue through analysis of the efficient and equitable spatial allocation of wind turbines and photovoltaic power plants in Germany. We combine multiple methods, including legal analysis, economic and energy modelling, monetary valuation and numerical optimization. We find that minimum distances between renewable power plants and human settlements should be as small as is legally possible. Even small reductions in efficiency lead to large increases in equity. By considering electricity grid expansion costs, we find a more even allocation of power plants across the country than is the case when grid expansion costs are neglected.

18 CFR 366.5 - Allocation of costs for non-power goods and services.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Allocation of costs for non-power goods and services. 366.5 Section 366.5 Conservation of Power and Water Resources FEDERAL... ACT OF 2005, FEDERAL POWER ACT AND NATURAL GAS ACT BOOKS AND RECORDS Definitions and Provisions Under...

18 CFR 366.5 - Allocation of costs for non-power goods and services.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Allocation of costs for non-power goods and services. 366.5 Section 366.5 Conservation of Power and Water Resources FEDERAL... ACT OF 2005, FEDERAL POWER ACT AND NATURAL GAS ACT BOOKS AND RECORDS Definitions and Provisions Under...

Microwave power transmitting phased array antenna research project

NASA Technical Reports Server (NTRS)

Dickinson, R. M.

1978-01-01

An initial design study and the development results of an S band RF power transmitting phased array antenna experiment system are presented. The array was to be designed, constructed and instrumented to permit wireless power transmission technology evaluation measurements. The planned measurements were to provide data relative to the achievable performance in the state of the art of flexible surface, retrodirective arrays, as a step in technically evaluating the satellite power system concept for importing to earth, via microwave beams, the nearly continuous solar power available in geosynchronous orbit. Details of the microwave power transmitting phased array design, instrumentation approaches, system block diagrams, and measured component and breadboard characteristics achieved are presented.

Speaking truth to power: the effect of candid feedback on how individuals with power allocate resources.

PubMed

Oc, Burak; Bashshur, Michael R; Moore, Celia

2015-03-01

Subordinates are often seen as impotent, able to react to but not affect how powerholders treat them. Instead, we conceptualize subordinate feedback as an important trigger of powerholders' behavioral self-regulation and explore subordinates' reciprocal influence on how powerholders allocate resources to them over time. In 2 experiments using a multiparty, multiround dictator game paradigm, we found that when subordinates provided candid feedback about whether they found prior allocations to be fair or unfair, powerholders regulated how self-interested their allocations were over time. However, when subordinates provided compliant feedback about powerholders' prior allocation decisions (offered consistently positive feedback, regardless of the powerholders' prior allocation), those powerholders made increasingly self-interested allocations over time. In addition, we showed that guilt partially mediates this relationship: powerholders feel more guilty after receiving negative feedback about an allocation, subsequently leading to a less self-interested allocation, whereas they feel less guilty after receiving positive feedback about an allocation, subsequently taking more for themselves. Our findings integrate the literature on upward feedback with theory about moral self-regulation to support the idea that subordinates are an important source of influence over those who hold power over them. PsycINFO Database Record (c) 2015 APA, all rights reserved.

Rocket Experiment on Construction of Huge Transmitting Antenna for the SPS Using Furoshiki Satellite System with Robots

NASA Astrophysics Data System (ADS)

Kaya, N.; Iwashita, M.; Nakasuka, S.; Summerer, L.; Mankins, J.

2004-12-01

Construction technology of huge structures is essential for the future space development as well as the Solar Power Satellite (SPS). The SPS needs huge antennas to transmit the generated electric power toward the ground, while the huge antenna have many useful applications in space as well as on the ground, for example, telecommunication for cellular phones, radars for remote sensing, navigation and observation, and so on. A parabola antenna was mostly used for the space antenna. However, it is very difficult for the larger parabola antenna to keep accuracy of the reflectors and the beam control, because the surfaces of the reflectors are mechanically supported and controlled. The huge space antenna with flexible and ultra-light structures is essential and necessary for the future applications. An active phased array antenna is more suitable and promising for the huge flexible antenna than the parabola antenna. We are proposing to apply the Furoshiki satellite [1] with robots for construction of the huge structures. While a web is deployed using the Furoshiki satellite in the same size of the huge antenna, all of the antenna elements crawl on the web with their own legs toward their allocated locations. We are verifying the deployment concept of the Furoshiki satellite using a sounding rocket with robots crawling on the deployed web. The robots are internationally being developed by NASA, ESA and Kobe University. The paper describes the concept of the crawling robot developed by Kobe University as well as the plan of the rocket experiment.

Optimal Power Control in Wireless Powered Sensor Networks: A Dynamic Game-Based Approach

PubMed Central

Xu, Haitao; Guo, Chao; Zhang, Long

2017-01-01

In wireless powered sensor networks (WPSN), it is essential to research uplink transmit power control in order to achieve throughput performance balancing and energy scheduling. Each sensor should have an optimal transmit power level for revenue maximization. In this paper, we discuss a dynamic game-based algorithm for optimal power control in WPSN. The main idea is to use the non-cooperative differential game to control the uplink transmit power of wireless sensors in WPSN, to extend their working hours and to meet QoS (Quality of Services) requirements. Subsequently, the Nash equilibrium solutions are obtained through Bellman dynamic programming. At the same time, an uplink power control algorithm is proposed in a distributed manner. Through numerical simulations, we demonstrate that our algorithm can obtain optimal power control and reach convergence for an infinite horizon. PMID:28282945

A transaction assessment method for allocation of transmission services

NASA Astrophysics Data System (ADS)

Banunarayanan, Venkatasubramaniam

The purpose of this research is to develop transaction assessment methods for allocating transmission services that are provided by an area/utility to power transactions. Transmission services are the services needed to deliver, or provide the capacity to deliver, real and reactive power from one or more supply points to one or more delivery points. As the number of transactions increase rapidly in the emerging deregulated environment, accurate quantification of the transmission services an area/utility provides to accommodate a transaction is becoming important, because then appropriate pricing schemes can be developed to compensate for the parties that provide these services. The Allocation methods developed are based on the "Fair Resource Allocation Principle" and they determine for each transaction the following: the flowpath of the transaction (both real and reactive power components), generator reactive power support from each area/utility, real power loss support from each area/utility. Further, allocation methods for distributing the cost of relieving congestion on transmission lines caused by transactions are also developed. The main feature of the proposed methods is representation of actual usage of the transmission services by the transactions. The proposed method is tested extensively on a variety of systems. The allocation methods developed in this thesis for allocation of transmission services to transactions is not only useful in studying the impact of transactions on a transmission system in a multi-transaction case, but they are indeed necessary to meet the criteria set forth by FERC with regard to pricing based on actual usage. The "consistency" of the proposed allocation methods has also been investigated and tested.

Reactive Power Pricing Model Considering the Randomness of Wind Power Output

NASA Astrophysics Data System (ADS)

Dai, Zhong; Wu, Zhou

2018-01-01

With the increase of wind power capacity integrated into grid, the influence of the randomness of wind power output on the reactive power distribution of grid is gradually highlighted. Meanwhile, the power market reform puts forward higher requirements for reasonable pricing of reactive power service. Based on it, the article combined the optimal power flow model considering wind power randomness with integrated cost allocation method to price reactive power. Meanwhile, considering the advantages and disadvantages of the present cost allocation method and marginal cost pricing, an integrated cost allocation method based on optimal power flow tracing is proposed. The model realized the optimal power flow distribution of reactive power with the minimal integrated cost and wind power integration, under the premise of guaranteeing the balance of reactive power pricing. Finally, through the analysis of multi-scenario calculation examples and the stochastic simulation of wind power outputs, the article compared the results of the model pricing and the marginal cost pricing, which proved that the model is accurate and effective.

Space transportation alternatives for large space programs: The International Space University Summer Session, 1992

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan A.

1993-01-01

In 1992, the International Space University (ISU) held its Summer Session in Kitakyushu, Japan. This paper summarizes and expands upon some aspects of space solar power and space transportation that were considered during that session. The issues discussed in this paper are the result of a 10-week study by the Space Solar Power Program design project members and the Space Transportation Group to investigate new paradigms in space propulsion and how those paradigms might reduce the costs for large space programs. The program plan was to place a series of power satellites in Earth orbit. Several designs were studied where many kW, MW, or GW of power would be transmitted to Earth or to other spacecraft in orbit. During the summer session, a space solar power system was also detailed and analyzed. A high-cost space transportation program is potentially the most crippling barrier to such a space power program. At ISU, the focus of the study was to foster and develop some of the new paradigms that may eliminate the barriers to low cost for space exploration and exploitation. Many international and technical aspects of a large multinational program were studied. Environmental safety, space construction and maintenance, legal and policy issues of frequency allocation, technology transfer and control and many other areas were addressed. Over 120 students from 29 countries participated in this summer session. The results discussed in this paper, therefore, represent the efforts of many nations.

Multicoil resonance-based parallel array for smart wireless power delivery.

PubMed

Mirbozorgi, S A; Sawan, M; Gosselin, B

2013-01-01

This paper presents a novel resonance-based multicoil structure as a smart power surface to wirelessly power up apparatus like mobile, animal headstage, implanted devices, etc. The proposed powering system is based on a 4-coil resonance-based inductive link, the resonance coil of which is formed by an array of several paralleled coils as a smart power transmitter. The power transmitter employs simple circuit connections and includes only one power driver circuit per multicoil resonance-based array, which enables higher power transfer efficiency and power delivery to the load. The power transmitted by the driver circuit is proportional to the load seen by the individual coil in the array. Thus, the transmitted power scales with respect to the load of the electric/electronic system to power up, and does not divide equally over every parallel coils that form the array. Instead, only the loaded coils of the parallel array transmit significant part of total transmitted power to the receiver. Such adaptive behavior enables superior power, size and cost efficiency then other solutions since it does not need to use complex detection circuitry to find the location of the load. The performance of the proposed structure is verified by measurement results. Natural load detection and covering 4 times bigger area than conventional topologies with a power transfer efficiency of 55% are the novelties of presented paper.

[A wireless power transmission system for capsule endoscope].

PubMed

Xin, Wenhui; Yan, Guozheng; Wang, Wenxing

2010-06-01

In order to deliver power to the capsule endoscope, whose position and orientation are always changing when traveling along the alimentary tract, a wireless power transmission system based on electromagnetic coupling was proposed. The system is composed of Helmholtz transmitting coil and three-dimensional receiving coil. Helmholtz coil outside the body generates a uniform magnetic field covering the whole alimentary tract; three-dimensional coil inside retrieves stable power regardless of its position and orientation. The transmitter and receiver were designed and implemented, and the experiments validated the feasibility of the system. The results show that at least 320 mW of usable power can be transmitted to capsule endoscope when its position and orientation are changing at random and the transmitting power is 25W.

Exploiting Artificial Intelligence for Analysis and Data Selection on-board the Puerto Rico CubeSat

NASA Astrophysics Data System (ADS)

Bergman, J. E. S.; Bruhn, F.; Funk, P.; Isham, B.; Rincón-Charris, A. A.; Capo-Lugo, P.; Åhlén, L.

2015-10-01

CubeSat missions are constrained by the limited resources provided by the platform. Many payload providers have learned to cope with the low mass and power but the poor telemetry allocation remains a bottleneck. In the end, it is the data delivered to ground which determines the value of the mission. However, transmitting more data does not necessarily guarantee high value, since the value also depends on the data quality. By exploiting fast on-board computing and efficient artificial intelligence (AI) algorithms for analysis and data selection one could optimize the usage of the telemetry link and so increase the value of the mission. In a pilot project, we attempt to do this on the Puerto Rico CubeSat, where science objectives include the acquisition of space weather data to aid better understanding of the Sun to Earth connection.

Allocation of Load-Loss Cost Caused by Voltage Sag

NASA Astrophysics Data System (ADS)

Gao, X.

2017-10-01

This paper focuses on the allocation of load-loss cost caused by voltage sag in the environment of electricity market. To compensate the loss of loads due to voltage sags, the load-loss cost is allocated to both sources and power consumers. On the basis of Load Drop Cost (LDC), a quantitative evaluation index of load-loss cost caused by voltage sag is identified. The load-loss cost to be allocated to power consumers themselves is calculated according to load classification. Based on the theory of power component the quantitative relation between sources and loads is established, thereby a quantitative calculation method for load-loss cost allocated to each source is deduced and the quantitative compensation from individual source to load is proposed. A simple five-bus system illustrates the main features of the proposed method.

Political model of social evolution

PubMed Central

Acemoglu, Daron; Egorov, Georgy; Sonin, Konstantin

2011-01-01

Almost all democratic societies evolved socially and politically out of authoritarian and nondemocratic regimes. These changes not only altered the allocation of economic resources in society but also the structure of political power. In this paper, we develop a framework for studying the dynamics of political and social change. The society consists of agents that care about current and future social arrangements and economic allocations; allocation of political power determines who has the capacity to implement changes in economic allocations and future allocations of power. The set of available social rules and allocations at any point in time is stochastic. We show that political and social change may happen without any stochastic shocks or as a result of a shock destabilizing an otherwise stable social arrangement. Crucially, the process of social change is contingent (and history-dependent): the timing and sequence of stochastic events determine the long-run equilibrium social arrangements. For example, the extent of democratization may depend on how early uncertainty about the set of feasible reforms in the future is resolved. PMID:22198760

Political model of social evolution.

PubMed

Acemoglu, Daron; Egorov, Georgy; Sonin, Konstantin

2011-12-27

Almost all democratic societies evolved socially and politically out of authoritarian and nondemocratic regimes. These changes not only altered the allocation of economic resources in society but also the structure of political power. In this paper, we develop a framework for studying the dynamics of political and social change. The society consists of agents that care about current and future social arrangements and economic allocations; allocation of political power determines who has the capacity to implement changes in economic allocations and future allocations of power. The set of available social rules and allocations at any point in time is stochastic. We show that political and social change may happen without any stochastic shocks or as a result of a shock destabilizing an otherwise stable social arrangement. Crucially, the process of social change is contingent (and history-dependent): the timing and sequence of stochastic events determine the long-run equilibrium social arrangements. For example, the extent of democratization may depend on how early uncertainty about the set of feasible reforms in the future is resolved.

Coverage Extension and Balancing the Transmitted Power of the Moving Relay Node at LTE-A Cellular Network

PubMed Central

Aldhaibani, Jaafar A.; Yahya, Abid; Ahmad, R. Badlishah

2014-01-01

The poor capacity at cell boundaries is not enough to meet the growing demand and stringent design which required high capacity and throughput irrespective of user's location in the cellular network. In this paper, we propose new schemes for an optimum fixed relay node (RN) placement in LTE-A cellular network to enhance throughput and coverage extension at cell edge region. The proposed approach mitigates interferences between all nodes and ensures optimum utilization with the optimization of transmitted power. Moreover, we proposed a new algorithm to balance the transmitted power of moving relay node (MR) over cell size and providing required SNR and throughput at the users inside vehicle along with reducing the transmitted power consumption by MR. The numerical analysis along with the simulation results indicates that an improvement in capacity for users is 40% increment at downlink transmission from cell capacity. Furthermore, the results revealed that there is saving nearly 75% from transmitted power in MR after using proposed balancing algorithm. ATDI simulator was used to verify the numerical results, which deals with real digital cartographic and standard formats for terrain. PMID:24672378

Coverage extension and balancing the transmitted power of the moving relay node at LTE-A cellular network.

PubMed

Aldhaibani, Jaafar A; Yahya, Abid; Ahmad, R Badlishah

2014-01-01

The poor capacity at cell boundaries is not enough to meet the growing demand and stringent design which required high capacity and throughput irrespective of user's location in the cellular network. In this paper, we propose new schemes for an optimum fixed relay node (RN) placement in LTE-A cellular network to enhance throughput and coverage extension at cell edge region. The proposed approach mitigates interferences between all nodes and ensures optimum utilization with the optimization of transmitted power. Moreover, we proposed a new algorithm to balance the transmitted power of moving relay node (MR) over cell size and providing required SNR and throughput at the users inside vehicle along with reducing the transmitted power consumption by MR. The numerical analysis along with the simulation results indicates that an improvement in capacity for users is 40% increment at downlink transmission from cell capacity. Furthermore, the results revealed that there is saving nearly 75% from transmitted power in MR after using proposed balancing algorithm. ATDI simulator was used to verify the numerical results, which deals with real digital cartographic and standard formats for terrain.

Solar power for the lunar night

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.

1989-01-01

Providing power over the 354 hour lunar night provides a considerable challenge to solar power concepts for a moonbase. Concepts are reviewed for providing night power for a solar powered moonbase. The categories of solutions considered are electrical storage, physical storage, transmitted power, and innovative concepts. Electrical storage is the most well-developed option. Less developed electrical storage options are capacitors and superconducting inductors. Physical storage options include storage of potential energy and storage of energy in flywheels. Thermal storage has potentially high energy/weight, but problems of conduction and radiation losses during the night need to be addressed. Transmitted power considers use of microwave or laser beams to transmit power either from orbit or directly from the Earth. Finally, innovative concepts proposed include reflecting light from orbital mirrors, locating the moonbase at a lunar pole, converting reflected Earthlight, or moving the moonbase to follow the sun.

AeroMACS Interference Simulations for Global Airports

NASA Technical Reports Server (NTRS)

Wilson, Jeffrey D.; Apaza, Rafael D.

2012-01-01

Ran 18 scenarios with Visualyse Professional interference software (presented 2 most realistic scenarios). Scenario A: 85 large airports can transmit 1650 mW on each of 11 channels. 173 medium airports can transmit 825 mW on each of 6 channels. 5951 small airports can transmit 275 mW on one channel. Reducing power allowed for small airports in Scenario B increases allowable power for large and medium airports, but should not be necessary as Scenario A levels are more than adequate. These power limitations are conservative because we are assuming worst case with 100% duty.

Effects of nymphal diet and adult feeding on allocation of resources to glassy-winged sharpshooter egg production

USDA-ARS?s Scientific Manuscript database

The glassy-winged sharpshooter is an invasive insect capable of transmitting the bacterial pathogen Xylella fastidiosa. Pre-oviposition periods of laboratory reared glassy-winged sharpshooters are variable. Here, two questions were addressed: does nymphal diet affect pre-oviposition period and how d...

Systems and assemblies for transferring high power laser energy through a rotating junction

DOEpatents

Norton, Ryan J.; McKay, Ryan P.; Fraze, Jason D.; Rinzler, Charles C.; Grubb, Daryl L.; Faircloth, Brian O.; Zediker, Mark S.

2016-01-26

There are provided high power laser devices and systems for transmitting a high power laser beam across a rotating assembly, including optical slip rings and optical rotational coupling assemblies. These devices can transmit the laser beam through the rotation zone in free space or within a fiber.

Update on the Solar Power Satellite transmitter design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, W.C.

1986-01-01

A number of remaining problems in the conceptual design of the transmitting antenna for the Solar Power Satellite have been solved as a result of additional technology development. Much of the technology was derived from the conceptual design of a ground-based transmitting antenna for beaming power to a high altitude airship or airplane.

Small, Optically-Driven Power Source

NASA Technical Reports Server (NTRS)

Cockrum, Richard H.; Wang, Ke-Li J.

1988-01-01

Power transmitted along fiber-optic cables. Transmitted as infrared light along fiber-optic cable, converted to electricity to supply small electronic circuit. Power source and circuit remains electrically isolated from each other for safety or reduces electromagnetic interference. Array of diodes made by standard integrated-circuit techniques and packaged for mounting at end of fiber-optic cable.

Adaptive power allocation schemes based on IAFS algorithm for OFDM-based cognitive radio systems

NASA Astrophysics Data System (ADS)

Zhang, Shuying; Zhao, Xiaohui; Liang, Cong; Ding, Xu

2017-01-01

In cognitive radio (CR) systems, reasonable power allocation can increase transmission rate of CR users or secondary users (SUs) as much as possible and at the same time insure normal communication among primary users (PUs). This study proposes an optimal power allocation scheme for the OFDM-based CR system with one SU influenced by multiple PU interference constraints. This scheme is based on an improved artificial fish swarm (IAFS) algorithm in combination with the advantage of conventional artificial fish swarm (ASF) algorithm and particle swarm optimisation (PSO) algorithm. In performance comparison of IAFS algorithm with other intelligent algorithms by simulations, the superiority of the IAFS algorithm is illustrated; this superiority results in better performance of our proposed scheme than that of the power allocation algorithms proposed by the previous studies in the same scenario. Furthermore, our proposed scheme can obtain higher transmission data rate under the multiple PU interference constraints and the total power constraint of SU than that of the other mentioned works.

75 FR 1616 - Post-2010 Resource Pool, Pick-Sloan Missouri Basin Program-Eastern Division

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-12

... Allocation for the new customer was calculated using the Procedures. As defined in the Post-1985 Marketing..., a Federal power marketing agency of the Department of Energy (DOE), hereby announces the Post-2010... need to withdraw power from existing customers. The Final Power Allocation is published to show Western...

Energy-efficient routing, modulation and spectrum allocation in elastic optical networks

NASA Astrophysics Data System (ADS)

Tan, Yanxia; Gu, Rentao; Ji, Yuefeng

2017-07-01

With tremendous growth in bandwidth demand, energy consumption problem in elastic optical networks (EONs) becomes a hot topic with wide concern. The sliceable bandwidth-variable transponder in EON, which can transmit/receive multiple optical flows, was recently proposed to improve a transponder's flexibility and save energy. In this paper, energy-efficient routing, modulation and spectrum allocation (EE-RMSA) in EONs with sliceable bandwidth-variable transponder is studied. To decrease the energy consumption, we develop a Mixed Integer Linear Programming (MILP) model with corresponding EE-RMSA algorithm for EONs. The MILP model jointly considers the modulation format and optical grooming in the process of routing and spectrum allocation with the objective of minimizing the energy consumption. With the help of genetic operators, the EE-RMSA algorithm iteratively optimizes the feasible routing path, modulation format and spectrum resources solutions by explore the whole search space. In order to save energy, the optical-layer grooming strategy is designed to transmit the lightpath requests. Finally, simulation results verify that the proposed scheme is able to reduce the energy consumption of the network while maintaining the blocking probability (BP) performance compare with the existing First-Fit-KSP algorithm, Iterative Flipping algorithm and EAMGSP algorithm especially in large network topology. Our results also demonstrate that the proposed EE-RMSA algorithm achieves almost the same performance as MILP on an 8-node network.

78 FR 26765 - Application to Export Electric Energy; ALLETE, Inc., d/b/a Minnesota Power

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-08

... DEPARTMENT OF ENERGY [OE Docket No. EA-196-D] Application to Export Electric Energy; ALLETE, Inc... renew its authority to transmit electric energy from the United States to Canada pursuant to section 202... Power to transmit electric energy from the United States to Canada as a power marketer for a five-year...

Modified Reference SPS with Solid State Transmitting Antenna

NASA Technical Reports Server (NTRS)

Woodcock, G. R.; Sperber, B. R.

1980-01-01

The development of solid state microwave power amplifiers for a solar power satellite transmitting antenna is discussed. State-of-the-art power-added efficiency, gain, and single device power of various microwave solid state devices are compared. The GaAs field effect transistors and the Si-bipolar transistors appear potentially feasible for solar power satellite use. The integration of solid state devices into antenna array elements is examined and issues concerning antenna integration and consequent satellite configurations are examined.

Laser multiplexing system

DOEpatents

Johnson, Steve A.; English, Jr., Ronald Edward; White, Ronald K.

2001-01-01

A plurality of copper lasers, as radiant power sources, emits a beam of power carrying radiation. A plurality of fiber injection assemblies receives power from the plurality of copper lasers and injects such power into a plurality of fibers for individually transmitting the received power to a plurality of power-receiving devices. The power-transmitting fibers of the system are so arranged that power is delivered therethrough to each of the power-receiving devices such that, even if a few of the radiant power sources and/or fibers fail, the power supply to any of the power receiving devices will not completely drop to zero but will drop by the same proportionate amount.

Powertrain with powersplit pump input and method of use thereof

DOEpatents

Johnson, Kris W.; Rose, Charles E.

2009-04-28

A powertrain includes an engine operatively connected to a primary power consuming device to transmit power thereto. The powertrain also includes a motor and a pump. The power output of the motor is independent of the power output of the engine. An epicyclic geartrain includes first, second and third members. The first member is operatively connected to the engine to receive power therefrom. The second member is operatively connected to the motor to receive power therefrom. The third member is operatively connected to the pump to transmit power thereto.

Inter-Vehicle Communication System Utilizing Autonomous Distributed Transmit Power Control

NASA Astrophysics Data System (ADS)

Hamada, Yuji; Sawa, Yoshitsugu; Goto, Yukio; Kumazawa, Hiroyuki

In ad-hoc network such as inter-vehicle communication (IVC) system, safety applications that vehicles broadcast the information such as car velocity, position and so on periodically are considered. In these applications, if there are many vehicles broadcast data in a communication area, congestion incurs a problem decreasing communication reliability. We propose autonomous distributed transmit power control method to keep high communication reliability. In this method, each vehicle controls its transmit power using feed back control. Furthermore, we design a communication protocol to realize the proposed method, and we evaluate the effectiveness of proposed method using computer simulation.

75 FR 76975 - 2015 Resource Pool-Sierra Nevada Region

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-10

...The Western Area Power Administration (Western), a Federal power marketing administration of DOE, announces the Final 2015 Resource Pool allocations pursuant to its 2004 Power Marketing Plan (Marketing Plan) for the Sierra Nevada Customer Service Region (SNR). This notice includes a summary of the comments received on Western's proposed 2015 Resource Pool allocations and Western's responses.

Apparatus and Method for Communication over Power Lines

NASA Technical Reports Server (NTRS)

Krasowski, Michael J. (Inventor); Prokop, Norman F. (Inventor); Greer, III, Lawrence C. (Inventor); Nappier, Jennifer M. (Inventor)

2017-01-01

An apparatus and method are provided for communicating over power lines. The apparatus includes a coupling modem that is situated between a power line and a device. The coupling modem is configured to demodulate a signal received from the power line into a sine signal and a cosine signal. The coupling modem is also configured to modulate a communicated bit stream received from the device into a transmitted signal in order to impose the transmitted signal onto the power line.

Apparatus and Method for Communication over Power Lines

NASA Technical Reports Server (NTRS)

Krasowski, Michael J. (Inventor); Prokop, Norman F. (Inventor); Greer, Lawrence C., III (Inventor); Nappier, Jennifer M. (Inventor)

2015-01-01

An apparatus and method are provided for communicating over power lines. The apparatus includes a coupling modem that is situated between a power line and a device. The coupling modem is configured to demodulate a signal received from the power line into a sine signal and a cosine signal. The coupling modem is also configured to modulate a communicated bit stream received from the device into a transmitted signal in order to impose the transmitted signal onto the power line.

Sexual Relationship Power as a Mediator between Dating Violence and Sexually Transmitted Infections among College Women

ERIC Educational Resources Information Center

Buelna, Christina; Ulloa, Emilio C.; Ulibarri, Monica D.

2009-01-01

This study examined relationship power as a possible mediator of the relationship between dating violence and sexually transmitted infections (STIs). The proposed mediation model was based on the theory of gender and power as well as previous research on intimate partner violence and STI risk. Survey results from a sample of 290 single,…

Design and Construction Multi Output Power Transmition with Single Prime Mover on Agricultural Products Machine

NASA Astrophysics Data System (ADS)

Koten, V. K.; Tanamal, C. E.

2017-03-01

Manufacturing agricultural products by the farmers, people or person who involve in medium industry, small industry, and households industry still be done in separately. Although the power on primemover is enough, in operations, primemover was only to move one of several agricultural products machine. This study attempts to design and construct power transmition multi output with single primemover; a single construction that allows primemover move some agricultur products machine in the same or not. This study begins with the determination of production capacity and the power to destroy products, the determination of resources and rotation, normalization of resources and rotation, the determination of the type material used, the size determination of each machine elements, construction machine elements, and assemble machine elements into a construction multi output power transmition with single primemover on agricultural products machine. The results show that with a input normalization 4 PK (2984 Watt), rotation 2000 rpm, the strength of material 60 kg/mm2, and several operating consideration, thus obtained size of machine elements through calculation. Based on the size, the machine elements is made through the use of some machine tools and assembled to form a multi output power transmition with single primemover.

Distributed Power Allocation for Wireless Sensor Network Localization: A Potential Game Approach.

PubMed

Ke, Mingxing; Li, Ding; Tian, Shiwei; Zhang, Yuli; Tong, Kaixiang; Xu, Yuhua

2018-05-08

The problem of distributed power allocation in wireless sensor network (WSN) localization systems is investigated in this paper, using the game theoretic approach. Existing research focuses on the minimization of the localization errors of individual agent nodes over all anchor nodes subject to power budgets. When the service area and the distribution of target nodes are considered, finding the optimal trade-off between localization accuracy and power consumption is a new critical task. To cope with this issue, we propose a power allocation game where each anchor node minimizes the square position error bound (SPEB) of the service area penalized by its individual power. Meanwhile, it is proven that the power allocation game is an exact potential game which has one pure Nash equilibrium (NE) at least. In addition, we also prove the existence of an ϵ -equilibrium point, which is a refinement of NE and the better response dynamic approach can reach the end solution. Analytical and simulation results demonstrate that: (i) when prior distribution information is available, the proposed strategies have better localization accuracy than the uniform strategies; (ii) when prior distribution information is unknown, the performance of the proposed strategies outperforms power management strategies based on the second-order cone program (SOCP) for particular agent nodes after obtaining the estimated distribution of agent nodes. In addition, proposed strategies also provide an instructional trade-off between power consumption and localization accuracy.

A Quasi-Optical Transmit/Receive Switch for the Goldstone Solar System Radar

NASA Technical Reports Server (NTRS)

Bhanji, Al

1997-01-01

A novel quasi-optical transmit/receive switch design for use with a high transmit power, low receive noise planetary imaging radar system is described. Design tradeoffs and implementation are discussed.

High bandwidth magnetically isolated signal transmission circuit

NASA Technical Reports Server (NTRS)

Repp, John Donald (Inventor)

2005-01-01

Many current electronic systems incorporate expensive or sensitive electrical components. Because electrical energy is often generated or transmitted at high voltages, the power supplies to these electronic systems must be carefully designed. Power supply design must ensure that the electrical system being supplied with power is not exposed to excessive voltages or currents. In order to isolate power supplies from electrical equipment, many methods have been employed. These methods typically involve control systems or signal transfer methods. However, these methods are not always suitable because of their drawbacks. The present invention relates to transmitting information across an interface. More specifically, the present invention provides an apparatus for transmitting both AC and DC information across a high bandwidth magnetic interface with low distortion.

18 CFR 367.28 - Methods of allocation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Methods of allocation... Instructions § 367.28 Methods of allocation. Indirect costs and compensation for use of capital must be allocated to projects in accordance with the service company's applicable and currently effective methods of...

18 CFR 367.28 - Methods of allocation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Methods of allocation... Instructions § 367.28 Methods of allocation. Indirect costs and compensation for use of capital must be allocated to projects in accordance with the service company's applicable and currently effective methods of...

Portable wireless power transmission system for video capsule endoscopy.

PubMed

Zhiwei, Jia; Guozheng, Yan; Bingquan, Zhu

2014-10-01

Wireless power transmission is considered a practical way of overcoming the power shortage of wireless capsule endoscopy (VCE). However, most patients cannot tolerate the long hours of lying in a fixed transmitting coil during diagnosis. To develop a portable wireless power transmission system for VCE, a compact transmitting coil and a portable inverter circuit driven by rechargeable batteries are proposed. The couple coils, optimized considering the stability and safety conditions, are 28 turns of transmitting coil and six strands of receiving coil. The driven circuit is designed according to the portable principle. Experiments show that the integrated system could continuously supply power to a dual-head VCE for more than 8 h at a frame rate of 30 frames per second with resolution of 320 × 240. The portable VCE exhibits potential for clinical applications, but requires further improvement and tests.

Two-way DF relaying assisted D2D communication: ergodic rate and power allocation

NASA Astrophysics Data System (ADS)

Ni, Yiyang; Wang, Yuxi; Jin, Shi; Wong, Kai-Kit; Zhu, Hongbo

2017-12-01

In this paper, we investigate the ergodic rate for a device-to-device (D2D) communication system aided by a two-way decode-and-forward (DF) relay node. We first derive closed-form expressions for the ergodic rate of the D2D link under asymmetric and symmetric cases, respectively. We subsequently discuss two special scenarios including weak interference case and high signal-to-noise ratio case. Then we derive the tight approximations for each of the considered scenarios. Assuming that each transmitter only has access to its own statistical channel state information (CSI), we further derive closed-form power allocation strategy to improve the system performance according to the analytical results of the ergodic rate. Furthermore, some insights are provided for the power allocation strategy based on the analytical results. The strategies are easy to compute and require to know only the channel statistics. Numerical results show the accuracy of the analysis results under various conditions and test the availability of the power allocation strategy.

Fabrication and researching of weathering resistant double cladding power delivery fiber

NASA Astrophysics Data System (ADS)

Rong, Liang; Ren, Junjiang; Li, Rundong; Wang, Lianping; Zou, Huan

2016-01-01

A novel well weathering resistant power delivery fiber which is of double cladding and high optical energy transmitting ability is developed via fluoroplastic out sheath extruding process. The fiber has been comprehensively evaluated including optical performance, mechanical performance, environmental suitability and laser transmitting property. It is shown that the fiber has not only low attenuation, high numerical aperture and better mechanical bending performance, but also outstanding weathering resistance and high power laser transmitting performance, which implies the qualification of the fiber for various kinds of applying situations, such as laser ignition, laser induced expanding sound underwater, ship-based and airborne laser weapon.

Wireless sensors powered by microbial fuel cells.

PubMed

Shantaram, Avinash; Beyenal, Haluk; Raajan, Raaja; Veluchamy, Angathevar; Lewandowski, Zbigniew

2005-07-01

Monitoring parameters characterizing water quality, such as temperature, pH, and concentrations of heavy metals in natural waters, is often followed by transmitting the data to remote receivers using telemetry systems. Such systems are commonly powered by batteries, which can be inconvenient at times because batteries have a limited lifetime and must be recharged or replaced periodically to ensure that sufficient energy is available to power the electronics. To avoid these inconveniences, a microbial fuel cell was designed to power electrochemical sensors and small telemetry systems to transmit the data acquired by the sensors to remote receivers. The microbial fuel cell was combined with low-power, high-efficiency electronic circuitry providing a stable power source for wireless data transmission. To generate enough power for the telemetry system, energy produced by the microbial fuel cell was stored in a capacitor and used in short bursts when needed. Since commercial electronic circuits require a minimum 3.3 V input and our cell was able to deliver a maximum of 2.1 V, a DC-DC converter was used to boost the potential. The DC-DC converter powered a transmitter, which gathered the data from the sensor and transmitted it wirelessly to a remote receiver. To demonstrate the utility of the system, temporal variations in temperature were measured, and the data were wirelessly transmitted to a remote receiver.

Optimal Power Allocation for CC-HARQ-based Cognitive Radio with Statistical CSI in Nakagami Slow Fading Channels

NASA Astrophysics Data System (ADS)

Xu, Ding; Li, Qun

2017-01-01

This paper addresses the power allocation problem for cognitive radio (CR) based on hybrid-automatic-repeat-request (HARQ) with chase combining (CC) in Nakagamimslow fading channels. We assume that, instead of the perfect instantaneous channel state information (CSI), only the statistical CSI is available at the secondary user (SU) transmitter. The aim is to minimize the SU outage probability under the primary user (PU) interference outage constraint. Using the Lagrange multiplier method, an iterative and recursive algorithm is derived to obtain the optimal power allocation for each transmission round. Extensive numerical results are presented to illustrate the performance of the proposed algorithm.

47 CFR 15.709 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... between the transmitter and the antenna. If transmitting antennas of directional gain greater than 6 dBi... gain of the antenna exceeds 6 dBi. (2) For personal/portable TVBDs, the maximum conducted output power... conducted output power shall not exceed 40 milliwatts. If transmitting antennas of directional gain greater...

Sex ratio and Wolbachia infection in the ant Formica exsecta.

PubMed

Keller, L; Liautard, C; Reuter, M; Brown, W D; Sundström, L; Chapuisat, M

2001-08-01

Sex allocation data in social Hymenoptera provide some of the best tests of kin selection, parent-offspring conflict and sex ratio theories. However, these studies critically depend on controlling for confounding ecological factors and on identifying all parties that potentially manipulate colony sex ratio. It has been suggested that maternally inherited parasites may influence sex allocation in social Hymenoptera. If the parasites can influence sex allocation, infected colonies are predicted to invest more resources in females than non-infected colonies, because the parasites are transmitted through females but not males. Prime candidates for such sex ratio manipulation are Wolbachia, because these cytoplasmically transmitted bacteria have been shown to affect the sex ratio of host arthropods by cytoplasmic incompatibility, parthenogenesis, male-killing and feminization. In this study, we tested whether Wolbachia infection is associated with colony sex ratio in two populations of the ant Formica exsecta that have been the subject of extensive sex ratio studies. In these populations colonies specialize in the production of one sex or the other. We found that almost all F. exsecta colonies in both populations are infected with Wolbachia. However, in neither population did we find a significant association in the predicted direction between the prevalence of Wolbachia and colony sex ratio. In particular, colonies with a higher proportion of infected workers did not produce more females. Hence, we conclude that Wolbachia does not seem to alter the sex ratio of its hosts as a means to increase transmission rate in these two populations of ants.

Development of a PLC modem for data transmission over a PWM power supply

NASA Astrophysics Data System (ADS)

Batard, Christophe; Ginot, Nicolas; Mannah, Marc Anthony; Millet, Christophe; Poitiers, Frédéric

2014-04-01

In variable-speed electrical drive and online conditioning monitoring, a feedback loop is required in order to transmit the sensor information from the motor to the controller close to the inverter. Additional cabling is used for signalling. This extra cabling has a significant cost and data transmission may not be reliable. Thus, the use of power line communication (PLC) technology to transmit data in motor drive application is quite interesting. The use of a PLC modem dedicated to the home network in a three-phase inverter-fed motor power cable does not work. Therefore, specific coupling interfaces are developed to transmit data through a pulse-width modulated power supply. Laboratory tests have shown that the couplers are operating properly. They ensure reliable data transmission in a motor drive application.

System for transmitting low frequency analog signals over AC power lines

DOEpatents

Baker, Steven P.; Durall, Robert L.; Haynes, Howard D.

1989-01-01

A system for transmitting low frequency analog signals over AC power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an AC power line. The modulation signal frequency range in selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the AC power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal.

System for transmitting low frequency analog signals over AC power lines

DOEpatents

Baker, Steven P.; Durall, Robert L.; Haynes, Howard D.

1989-09-05

A system for transmitting low frequency analog signals over AC power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an AC power line. The modulation signal frequency range in selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the AC power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal.

A Simplified GCS-DCSK Modulation and Its Performance Optimization

NASA Astrophysics Data System (ADS)

Xu, Weikai; Wang, Lin; Chi, Chong-Yung

2016-12-01

In this paper, a simplified Generalized Code-Shifted Differential Chaos Shift Keying (GCS-DCSK) whose transmitter never needs any delay circuits, is proposed. However, its performance is deteriorated because the orthogonality between substreams cannot be guaranteed. In order to optimize its performance, the system model of the proposed GCS-DCSK with power allocations on substreams is presented. An approximate bit error rate (BER) expression of the proposed model, which is a function of substreams’ power, is derived using Gaussian Approximation. Based on the BER expression, an optimal power allocation strategy between information substreams and reference substream is obtained. Simulation results show that the BER performance of the proposed GCS-DCSK with the optimal power allocation can be significantly improved when the number of substreams M is large.

US objectives generally achieved at broadcasting satellite international conference. Improvements can help in future conferences

NASA Astrophysics Data System (ADS)

1984-08-01

The implementation of broadcasting satellite service for the Western Hemisphere was planned. Broadcasting satellites transmit television programs and other information services from Earth orbit to home or office antennas. At the request of the Senate Appropriations Subcommittee on Commerce, Justice, State and the Judiciary, GAO reviewed conference results as compared to established conference objectives and examined the interagency coordination of U.S. participation in this international conference. The United States basically achieved its two most important conference objectives: adopting a technically and procedurally flexible plan for broadcasting satellite service and obtaining a sufficient allocation of satellite orbit slots and frequencies to meet domestic needs. The U.S. was unable, however, to obtain agreement on adopting a maximum signal power level for satellites. The Department of State could improve its preparation, internal coordination, and administrative support for future international conferences and recommends actions to the Secretary of State to improve its international telecommunications activities.

Beamed microwave power transmitting and receiving subsystems radiation characteristics

NASA Technical Reports Server (NTRS)

Dickinson, R. M.

1980-01-01

Measured characteristics of the spectrum of typical converters and the distribution of radiated Radio Frequency (RF) energy from the terminals (transmitting antenna and rectenna) of a beamed microwave power subsystem are presented for small transmitting and receiving S-band (2.45 GHz) subarrays. Noise and harmonic levels of tube and solid-state RF power amplifiers are shown. The RF patterns and envelope of a 64 element slotted waveguide antenna are given for the fundamental frequency and harmonics through the fifth. Reflected fundamental and harmonic patterns through the fourth for a 42 element rectenna subarray are presented for various dc load and illumination conditions. Bandwidth measurements for the waveguide antenna and rectenna are shown.

The 'Moskva' satellite television broadcasting system

NASA Astrophysics Data System (ADS)

Kantor, L. Ia.; Minashin, V. P.; Povolotskii, I. S.; Sokolov, A. V.; Talyzin, N. V.

1980-01-01

The Moskva television broadcasting system which uses the high-power links from the Gorizont satellite is described. The transmitting device of the ground station is similar to that of the Ekran and Intersputnik systems. The system includes a special television signal processing unit, a unit for introducing dispersion signals, and transmitting equipment for the sound and radio-broadcasting channels. The signal translated by the satellite is received by a network of ground receiving stations and fed to a television transmitter with a power of 1, 10, or 100 W. The signal in the radio-broadcasting channel can be transmitted into the local radio repeater network or transmitted by a USW FM radio-broadcasting transmitter. The results of system tests are provided.

47 CFR 15.407 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the peak power spectral density shall be reduced by the amount in dB that the directional gain of... density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain...

47 CFR 15.407 - General technical requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the peak power spectral density shall be reduced by the amount in dB that the directional gain of... density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain...

47 CFR 15.407 - General technical requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the peak power spectral density shall be reduced by the amount in dB that the directional gain of... density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain...

Game theoretic power allocation and waveform selection for satellite communications

NASA Astrophysics Data System (ADS)

Shu, Zhihui; Wang, Gang; Tian, Xin; Shen, Dan; Pham, Khanh; Blasch, Erik; Chen, Genshe

2015-05-01

Game theory is a useful method to model interactions between agents with conflicting interests. In this paper, we set up a Game Theoretic Model for Satellite Communications (SATCOM) to solve the interaction between the transmission pair (blue side) and the jammer (red side) to reach a Nash Equilibrium (NE). First, the IFT Game Application Model (iGAM) for SATCOM is formulated to improve the utility of the transmission pair while considering the interference from a jammer. Specifically, in our framework, the frame error rate performance of different modulation and coding schemes is used in the game theoretic solution. Next, the game theoretic analysis shows that the transmission pair can choose the optimal waveform and power given the received power from the jammer. We also describe how the jammer chooses the optimal power given the waveform and power allocation from the transmission pair. Finally, simulations are implemented for the iGAM and the simulation results show the effectiveness of the SATCOM power allocation, waveform selection scheme, and jamming mitigation.

Optimal Power Allocation for Downstream xDSL With Per-Modem Total Power Constraints: Broadcast Channel Optimal Spectrum Balancing (BC-OSB)

NASA Astrophysics Data System (ADS)

Le Nir, Vincent; Moonen, Marc; Verlinden, Jan; Guenach, Mamoun

2009-02-01

Recently, the duality between Multiple Input Multiple Output (MIMO) Multiple Access Channels (MAC) and MIMO Broadcast Channels (BC) has been established under a total power constraint. The same set of rates for MAC can be achieved in BC exploiting the MAC-BC duality formulas while preserving the total power constraint. In this paper, we describe the BC optimal power allo- cation applying this duality in a downstream x-Digital Subscriber Lines (xDSL) context under a total power constraint for all modems over all tones. Then, a new algorithm called BC-Optimal Spectrum Balancing (BC-OSB) is devised for a more realistic power allocation under per-modem total power constraints. The capacity region of the primal BC problem under per-modem total power constraints is found by the dual optimization problem for the BC under per-modem total power constraints which can be rewritten as a dual optimization problem in the MAC by means of a precoder matrix based on the Lagrange multipliers. We show that the duality gap between the two problems is zero. The multi-user power allocation problem has been solved for interference channels and MAC using the OSB algorithm. In this paper we solve the problem of multi-user power allocation for the BC case using the OSB algorithm as well and we derive a computational efficient algorithm that will be referred to as BC-OSB. Simulation results are provided for two VDSL2 scenarios: the first one with Differential-Mode (DM) transmission only and the second one with both DM and Phantom- Mode (PM) transmissions.

10 CFR Appendix D to Subpart D of... - Classes of Actions that Normally Require EISs

Code of Federal Regulations, 2014 CFR

2014-01-01

... [Reserved] D7 Contracts, policies, and marketing and allocation plans for electric power D8 Import or export... operational change D10 Treatment, storage, and disposal facilities for high-level waste and spent nuclear fuel... Contracts, Policies, and Marketing and Allocation Plans for Electric Power Establishment and implementation...

75 FR 78988 - Post-2014 Resource Pool-Loveland Area Projects, Allocation Procedures and Call for Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-17

... Administration (Western), a Federal power marketing agency of the Department of Energy (DOE), is publishing this... allocation of Federal electric power. Subpart C of the Energy Planning and Management Program (Program... for applications, in conjunction with the Loveland Area Projects (LAP) Final Post-1989 Marketing Plan...

Bandwidth characteristics of multimedia data traffic on a local area network

NASA Technical Reports Server (NTRS)

Chuang, Shery L.; Doubek, Sharon; Haines, Richard F.

1993-01-01

Limited spacecraft communication links call for users to investigate the potential use of video compression and multimedia technologies to optimize bandwidth allocations. The objective was to determine the transmission characteristics of multimedia data - motion video, text or bitmap graphics, and files transmitted independently and simultaneously over an ethernet local area network. Commercial desktop video teleconferencing hardware and software and Intel's proprietary Digital Video Interactive (DVI) video compression algorithm were used, and typical task scenarios were selected. The transmission time, packet size, number of packets, and network utilization of the data were recorded. Each data type - compressed motion video, text and/or bitmapped graphics, and a compressed image file - was first transmitted independently and its characteristics recorded. The results showed that an average bandwidth of 7.4 kilobits per second (kbps) was used to transmit graphics; an average bandwidth of 86.8 kbps was used to transmit an 18.9-kilobyte (kB) image file; a bandwidth of 728.9 kbps was used to transmit compressed motion video at 15 frames per second (fps); and a bandwidth of 75.9 kbps was used to transmit compressed motion video at 1.5 fps. Average packet sizes were 933 bytes for graphics, 498.5 bytes for the image file, 345.8 bytes for motion video at 15 fps, and 341.9 bytes for motion video at 1.5 fps. Simultaneous transmission of multimedia data types was also characterized. The multimedia packets used transmission bandwidths of 341.4 kbps and 105.8kbps. Bandwidth utilization varied according to the frame rate (frames per second) setting for the transmission of motion video. Packet size did not vary significantly between the data types. When these characteristics are applied to Space Station Freedom (SSF), the packet sizes fall within the maximum specified by the Consultative Committee for Space Data Systems (CCSDS). The uplink of imagery to SSF may be performed at minimal frame rates and/or within seconds of delay, depending on the user's allocated bandwidth. Further research to identify the acceptable delay interval and its impact on human performance is required. Additional studies in network performance using various video compression algorithms and integrated multimedia techniques are needed to determine the optimal design approach for utilizing SSF's data communications system.

A Wind Energy Powered Wireless Temperature Sensor Node

PubMed Central

Zhang, Chuang; He, Xue-Feng; Li, Si-Yu; Cheng, Yao-Qing; Rao, Yang

2015-01-01

A wireless temperature sensor node composed of a piezoelectric wind energy harvester, a temperature sensor, a microcontroller, a power management circuit and a wireless transmitting module was developed. The wind-induced vibration energy harvester with a cuboid chamber of 62 mm × 19.6 mm × 10 mm converts ambient wind energy into electrical energy to power the sensor node. A TMP102 temperature sensor and the MSP430 microcontroller are used to measure the temperature. The power management module consists of LTC3588-1 and LT3009 units. The measured temperature is transmitted by the nRF24l01 transceiver. Experimental results show that the critical wind speed of the harvester was about 5.4 m/s and the output power of the harvester was about 1.59 mW for the electrical load of 20 kΩ at wind speed of 11.2 m/s, which was sufficient to power the wireless sensor node to measure and transmit the temperature every 13 s. When the wind speed increased from 6 m/s to 11.5 m/s, the self-powered wireless sensor node worked normally. PMID:25734649

A wind energy powered wireless temperature sensor node.

PubMed

Zhang, Chuang; He, Xue-Feng; Li, Si-Yu; Cheng, Yao-Qing; Rao, Yang

2015-02-27

A wireless temperature sensor node composed of a piezoelectric wind energy harvester, a temperature sensor, a microcontroller, a power management circuit and a wireless transmitting module was developed. The wind-induced vibration energy harvester with a cuboid chamber of 62 mm × 19.6 mm × 10 mm converts ambient wind energy into electrical energy to power the sensor node. A TMP102 temperature sensor and the MSP430 microcontroller are used to measure the temperature. The power management module consists of LTC3588-1 and LT3009 units. The measured temperature is transmitted by the nRF24l01 transceiver. Experimental results show that the critical wind speed of the harvester was about 5.4 m/s and the output power of the harvester was about 1.59 mW for the electrical load of 20 kΩ at wind speed of 11.2 m/s, which was sufficient to power the wireless sensor node to measure and transmit the temperature every 13 s. When the wind speed increased from 6 m/s to 11.5 m/s, the self-powered wireless sensor node worked normally.

76 FR 60736 - Protection of Stratospheric Ozone: The 2011 Critical Use Exemption From the Phaseout of Methyl...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-30

... Allocations G. The Criteria in Decisions IX/6 and Ex. I/4 H. Emissions Minimization VI. Statutory and... issued several Decisions pertaining to the critical use exemption. These include Decisions IX/6 and Ex. I..., one for post-harvest uses and one for pre-plant uses. The USG transmitted responses to MBTOC on April...

Smart LED allocation scheme for efficient multiuser visible light communication networks.

PubMed

Sewaiwar, Atul; Tiwari, Samrat Vikramaditya; Chung, Yeon Ho

2015-05-18

In a multiuser bidirectional visible light communication (VLC), a large number of LEDs or an LED array needs to be allocated in an efficient manner to ensure sustainable data rate and link quality. Moreover, in order to support an increasing or decreasing number of users in the network, the LED allocation is required to be performed dynamically. In this paper, a novel smart LED allocation scheme for efficient multiuser VLC networks is presented. The proposed scheme allocates RGB LEDs to multiple users in a dynamic and efficient fashion, while satisfying illumination requirements in an indoor environment. The smart LED array comprised of RGB LEDs is divided into sectors according to the location of the users. The allocated sectors then provide optical power concentration toward the users for efficient and reliable data transmission. An algorithm for the dynamic allocation of the LEDs is also presented. To verify its effective resource allocation feature of the proposed scheme, simulations were performed. It is found that the proposed smart LED allocation scheme provides the effect of optical beamforming toward individual users, thereby increasing the collective power concentration of the optical signals on the desirable users and resulting in significantly increased data rate, while ensuring sufficient illumination in a multiuser VLC environment.

76 FR 19069 - Application to Export Electric Energy; Cargill Power Markets, LLC

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-06

... application. SUMMARY: Cargill Power Markets, LLC (CPM) has applied to renew its authority to transmit electric... Order No. EA-209, which authorized CPM to transmit electric energy from the United States to Canada as a... CPM export authorization two additional times: On July 3, 2001 in Order No. EA-209-A and on May 31...

18 CFR 2.20 - Good faith requests for transmission services and good faith responses by transmitting utilities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Good faith requests for transmission services and good faith responses by transmitting utilities. 2.20 Section 2.20 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES...

18 CFR 2.20 - Good faith requests for transmission services and good faith responses by transmitting utilities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Good faith requests for transmission services and good faith responses by transmitting utilities. 2.20 Section 2.20 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES...

18 CFR 2.20 - Good faith requests for transmission services and good faith responses by transmitting utilities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Good faith requests for transmission services and good faith responses by transmitting utilities. 2.20 Section 2.20 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES...

77 FR 15091 - Application To Export Electric Energy; DTE Energy Trading, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-14

... DEPARTMENT OF ENERGY [OE Docket No. EA-211-C] Application To Export Electric Energy; DTE Energy... transmit electric energy from the United States to Canada pursuant to section 202(e) of the Federal Power... transmit electric energy from the United States to Canada as a power marketer for a two-year term using...

18 CFR 36.1 - Notice provisions applicable to applications for transmission services under section 211 of the...

Code of Federal Regulations, 2010 CFR

2010-04-01

... arrangements for the sale or purchase of electric energy to be transmitted pursuant to the particular... Federal Power Act, 16 U.S.C. 796(23), being requested to transmit such electric energy. (3) Affected State... 36.1 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

Multi-Hop Link Capacity of Multi-Route Multi-Hop MRC Diversity for a Virtual Cellular Network

NASA Astrophysics Data System (ADS)

Daou, Imane; Kudoh, Eisuke; Adachi, Fumiyuki

In virtual cellular network (VCN), proposed for high-speed mobile communications, the signal transmitted from a mobile terminal is received by some wireless ports distributed in each virtual cell and relayed to the central port that acts as a gateway to the core network. In this paper, we apply the multi-route MHMRC diversity in order to decrease the transmit power and increase the multi-hop link capacity. The transmit power, the interference power and the link capacity are evaluated for DS-CDMA multi-hop VCN by computer simulation. The multi-route MHMRC diversity can be applied to not only DS-CDMA but also other access schemes (i. e. MC-CDMA, OFDM, etc.).

Research on power source structure optimization for East China Power Grid

NASA Astrophysics Data System (ADS)

Xu, Lingjun; Sang, Da; Zhang, Jianping; Tang, Chunyi; Xu, Da

2017-05-01

The structure of east china power grid is not reasonable for the coal power takes a much higher proportion than hydropower, at present the coal power takes charge of most peak load regulation, and the pressure of peak load regulation cannot be ignored. The nuclear power, wind power, photovoltaic, other clean energy and hydropower, coal power and wind power from outside will be actively developed in future, which increases the pressure of peak load regulation. According to development of economic and social, Load status and load prediction, status quo and planning of power source and the characteristics of power source, the peak load regulation balance is carried out and put forward a reasonable plan of power source allocation. The ultimate aim is to optimize the power source structure and to provide reference for power source allocation in east china.

Small-area low-power heart condition monitoring system using dual-mode SAR-ADC for low-cost wearable healthcare systems.

PubMed

Shin, Young-San; Wee, Jae-Kyung; Song, Inchae; Lee, Seongsoo

2015-01-01

Heart rate monitoring is useful to detect many cardiovascular diseases. It can be implemented in a small device with low power consumption, and it can exploit low-cost piezoelectric pressure sensors to measure heart rate. However, it is also desirable to transmit heartbeat waveform for emergency treatment, which significantly increases transmission power. In this paper, a low-cost wireless heart condition monitoring SoC is proposed. It can monitor and transmit both heart rate and heartbeat waveform, but the hardware is extremely simplified to achieve in a small package. By slight modification of successive-approximation analog-digital converter, it can count heart rate and read out heartbeat waveform with the same hardware. In the normal mode, only an 8-bit heart rate is transmitted for power reduction. If the heart rate is out of a given range, it goes to the emergency mode and a 10-bit heartbeat waveform is transmitted for fast treatment. The fabricated chip size is 1.1 mm2 in 0.11 μ m CMOS technology, including the radio-frequency transmitter. The measured power consumption is 161.8 μ W in normal mode and 507.3 μ W in emergency mode, respectively. The proposed SoC achieves low-cost, small area, and low-power. It is useful as part of a disposable healthcare system.

Design optimization of transmitting antennas for weakly coupled magnetic induction communication systems

PubMed Central

2017-01-01

This work focuses on the design of transmitting coils in weakly coupled magnetic induction communication systems. We propose several optimization methods that reduce the active, reactive and apparent power consumption of the coil. These problems are formulated as minimization problems, in which the power consumed by the transmitting coil is minimized, under the constraint of providing a required magnetic field at the receiver location. We develop efficient numeric and analytic methods to solve the resulting problems, which are of high dimension, and in certain cases non-convex. For the objective of minimal reactive power an analytic solution for the optimal current distribution in flat disc transmitting coils is provided. This problem is extended to general three-dimensional coils, for which we develop an expression for the optimal current distribution. Considering the objective of minimal apparent power, a method is developed to reduce the computational complexity of the problem by transforming it to an equivalent problem of lower dimension, allowing a quick and accurate numeric solution. These results are verified experimentally by testing a number of coil geometries. The results obtained allow reduced power consumption and increased performances in magnetic induction communication systems. Specifically, for wideband systems, an optimal design of the transmitter coil reduces the peak instantaneous power provided by the transmitter circuitry, and thus reduces its size, complexity and cost. PMID:28192463

[An implantable micro-device using wireless power transmission for measuring aortic aneurysm sac pressure].

PubMed

Guo, Xudong; Ge, Bin; Wang, Wenxing

2013-08-01

In order to detect endoleaks after endovascular aneurysm repair (EVAR), we developed an implantable micro-device based on wireless power transmission to measure aortic aneurysm sac pressure. The implantable micro-device is composed of a miniature wireless pressure sensor, an energy transmitting coil, a data recorder and a data processing platform. Power transmission without interconnecting wires is performed by a transmitting coil and a receiving coil. The coupling efficiency of wireless power transmission depends on the coupling coefficient between the transmitting coil and the receiving coil. With theoretical analysis and experimental study, we optimized the geometry of the receiving coil to increase the coupling coefficient. In order to keep efficiency balance and satisfy the maximizing conditions, we designed a closed loop power transmission circuit, including a receiving voltage feedback module based on wireless communication. The closed loop improved the stability and reliability of transmission energy. The prototype of the micro-device has been developed and the experiment has been performed. The experiments showed that the micro-device was feasible and valid. For normal operation, the distance between the transmitting coil and the receiving coil is smaller than 8cm. Besides, the distance between the micro-device and the data recorder is within 50cm.

COOPERATIVE ROUTING FOR DYNAMIC AERIAL LAYER NETWORKS

DTIC Science & Technology

2018-03-01

Advisor, Computing & Communications Division Information Directorate This report is published in the interest of scientific and technical...information accumulation at the physical layer, and study the cooperative routing and resource allocation problems associated with such SU networks...interference power constraint is studied . In [Shi2012Joint], an optimal power and sub-carrier allocation strategy to maximize SUs’ throughput subject to

Joint optimization of regional water-power systems

NASA Astrophysics Data System (ADS)

Pereira-Cardenal, Silvio J.; Mo, Birger; Gjelsvik, Anders; Riegels, Niels D.; Arnbjerg-Nielsen, Karsten; Bauer-Gottwein, Peter

2016-06-01

Energy and water resources systems are tightly coupled; energy is needed to deliver water and water is needed to extract or produce energy. Growing pressure on these resources has raised concerns about their long-term management and highlights the need to develop integrated solutions. A method for joint optimization of water and electric power systems was developed in order to identify methodologies to assess the broader interactions between water and energy systems. The proposed method is to include water users and power producers into an economic optimization problem that minimizes the cost of power production and maximizes the benefits of water allocation, subject to constraints from the power and hydrological systems. The method was tested on the Iberian Peninsula using simplified models of the seven major river basins and the power market. The optimization problem was successfully solved using stochastic dual dynamic programming. The results showed that current water allocation to hydropower producers in basins with high irrigation productivity, and to irrigation users in basins with high hydropower productivity was sub-optimal. Optimal allocation was achieved by managing reservoirs in very distinct ways, according to the local inflow, storage capacity, hydropower productivity, and irrigation demand and productivity. This highlights the importance of appropriately representing the water users' spatial distribution and marginal benefits and costs when allocating water resources optimally. The method can handle further spatial disaggregation and can be extended to include other aspects of the water-energy nexus.

Exploiting artificial intelligence for in-situ analysis of high-resolution radio emission measurements on a CubeSat

NASA Astrophysics Data System (ADS)

Isham, Brett; Bergman, Jan; Krause, Linda; Rincon-Charris, Amilcar; Bruhn, Fredrik; Funk, Peter; Stramkals, Arturs

2016-07-01

CubeSat missions are intentionally constrained by the limitations of their small platform. Mission payloads designed for low volume, mass, and power, may however be disproportionally limited by available telemetry allocations. In many cases, it is the data delivered to the ground which determines the value of the mission. However, transmitting more data does not necessarily guarantee high value, since the value also depends on data quality. By exploiting fast on-board computing and efficient artificial intelligence (AI) algorithms for analysis and data selection, the usage of the telemetry link can be optimized and value added to the mission. This concept is being implemented on the Puerto Rico CubeSat, which will make measurements of ambient ionospheric radio waves and ion irregularities and turbulence. Principle project goals include providing aerospace and systems engineering experiences to students. Science objectives include the study of natural space plasma processes to aid in better understanding of space weather and the Sun to Earth connection, and in-situ diagnostics of ionospheric modification experiments using high-power ground-based radio transmitters. We hope that this project might point the way to the productive use of AI in space and other remote, low-data-bandwidth environments.

Load allocation of power plant using multi echelon economic dispatch

NASA Astrophysics Data System (ADS)

Wahyuda, Santosa, Budi; Rusdiansyah, Ahmad

2017-11-01

In this paper, the allocation of power plant load which is usually done with a single echelon as in the load flow calculation, is expanded into a multi echelon. A plant load allocation model based on the integration of economic dispatch and multi-echelon problem is proposed. The resulting model is called as Single Objective Multi Echelon Economic Dispatch (SOME ED). This model allows the distribution of electrical power in more detail in the transmission and distribution substations along the existing network. Considering the interconnection system where the distance between the plant and the load center is usually far away, therefore the loss in this model is seen as a function of distance. The advantages of this model is its capability of allocating electrical loads properly, as well as economic dispatch information with the flexibility of electric power system as a result of using multi-echelon. In this model, the flexibility can be viewed from two sides, namely the supply and demand sides, so that the security of the power system is maintained. The model was tested on a small artificial data. The results demonstrated a good performance. It is still very open to further develop the model considering the integration with renewable energy, multi-objective with environmental issues and applied to the case with a larger scale.

18 CFR 367.17 - Comprehensive inter-period income tax allocation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Comprehensive inter... NATURAL GAS ACT General Instructions § 367.17 Comprehensive inter-period income tax allocation. (a) Where... tax method. In general, comprehensive inter-period tax allocation should be followed whenever...

Wireless power transmission for battery charging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mi, Chris; Li, Siqi; Nguyen, Trong-Duy

A wireless power transmission system is provided for high power applications. The power transmission system is comprised generally of a charging unit configured to generate an alternating electromagnetic field and a receive unit configured to receive the alternating electromagnetic field from the charging unit. The charging unit includes a power source; an input rectifier; an inverter; and a transmit coil. The transmit coil has a spirangle arrangement segmented into n coil segments with capacitors interconnecting adjacent coil segments. The receive unit includes a receive coil and an output rectifier. The receive coil also has a spirangle arrangement segmented into mmore » coil segments with capacitors interconnecting adjacent coil segments.« less

Inverter communications using output signal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chapman, Patrick L.

Technologies for communicating information from an inverter configured for the conversion of direct current (DC) power generated from an alternative source to alternating current (AC) power are disclosed. The technologies include determining information to be transmitted from the inverter over a power line cable connected to the inverter and controlling the operation of an output converter of the inverter as a function of the information to be transmitted to cause the output converter to generate an output waveform having the information modulated thereon.

An MBS-Assisted Femtocell Transmit Power Control Scheme with Mobile User QoS Guarantee in 2-Tier Heterogeneous Femtocell Networks

PubMed Central

Yang, Chih-Cheng; Sheu, Shiann-Tsong

2013-01-01

This study investigates how to adjust the transmit power of femto base station (FBS) to mitigate interference problems between the FBSs and mobile users (MUs) in the 2-tier heterogeneous femtocell networks. A common baseline of deploying the FBS to increase the indoor access bandwidth requires that the FBS operation will not affect outdoor MUs operation with their quality-of-service (QoS) requirements. To tackle this technical problem, an FBS transmit power adjustment (FTPA) algorithm is proposed to adjust the FBS transmit power (FTP) to avoid unwanted cochannel interference (CCI) with the neighboring MUs in downlink transmission. FTPA reduces the FTP to serve its femto users (FUs) according to the QoS requirements of the nearest neighboring MUs to the FBS so that the MU QoS requirement is guaranteed. Simulation results demonstrate that FTPA can achieve a low MU outage probability as well as serve FUs without violating the MU QoS requirements. Simulation results also reveal that FTPA has better performance on voice and video services which are the major trend of future multimedia communication in the NGN. PMID:24391461

Improving RF Transmit Power and Received Signal Strength in 2.4 GHz ZigBee Based Active RFID System with Embedded Method

NASA Astrophysics Data System (ADS)

Po'ad, F. A.; Ismail, W.; Jusoh, J. F.

2017-08-01

This paper describes the experiments and analysis conducted on 2.4 GHz embedded active Radio Frequency Identification (RFID) - Wireless Sensor Network (WSN) based system that has been developed for the purposes of location tracking and monitoring in indoor and outdoor environments. Several experiments are conducted to test the effectiveness and performance of the developed system and two of them is by measuring the Radio Frequency (RF) transmitting power and Received Signal Strength (RSS) to prove that the embedded active RFID tag is capable to generate higher transmit power during data transmission and able to provide better RSS reading compared to standalone RFID tag. Experiments are carried out on two RFID tags which are active RFID tag embedded with GPS and GSM (ER2G); and standalone RFID tag communicating with the same active RFID reader. The developed ER2G contributes 12.26 % transmit power and 6.47 % RSS reading higher than standalone RFID tag. The results conclude that the ER2G gives better performance compared to standalone RFID tag and can be used as guidelines for future design improvements.

An MBS-assisted femtocell transmit power control scheme with mobile user QoS guarantee in 2-tier heterogeneous femtocell networks.

PubMed

Chen, Jenhui; Yang, Chih-Cheng; Sheu, Shiann-Tsong

2013-01-01

This study investigates how to adjust the transmit power of femto base station (FBS) to mitigate interference problems between the FBSs and mobile users (MUs) in the 2-tier heterogeneous femtocell networks. A common baseline of deploying the FBS to increase the indoor access bandwidth requires that the FBS operation will not affect outdoor MUs operation with their quality-of-service (QoS) requirements. To tackle this technical problem, an FBS transmit power adjustment (FTPA) algorithm is proposed to adjust the FBS transmit power (FTP) to avoid unwanted cochannel interference (CCI) with the neighboring MUs in downlink transmission. FTPA reduces the FTP to serve its femto users (FUs) according to the QoS requirements of the nearest neighboring MUs to the FBS so that the MU QoS requirement is guaranteed. Simulation results demonstrate that FTPA can achieve a low MU outage probability as well as serve FUs without violating the MU QoS requirements. Simulation results also reveal that FTPA has better performance on voice and video services which are the major trend of future multimedia communication in the NGN.

Alcohol, Tobacco and Other Drugs in the Lives of Young Children. Building Community Systems for Young Children.

ERIC Educational Resources Information Center

Gardner, Sid; Young, Nancy

Substance abuse is a family disease, which can be transmitted both genetically and by the family environment. Legal and illegal use of alcohol, tobacco, and other drugs (ATOD) can affect children through a number of avenues. In planning for allocation of Proposition 10 funds, the use, abuse, and dependence on ATOD by parents, siblings, relatives,…

Flexible power and bandwidth allocation in mobile satellites

NASA Astrophysics Data System (ADS)

Keyes, L. A.

The introduction of L-band mobile communication services by spot beam satellites creates a payload design challenge due to uncertainty in the location and size of the new market to be served. A combination of payload technologies that allow a flexible allocation of power and bandwidth to any portion of the coverage area is described. Power flexibility is achieved by a novel combination of a low-level beam-forming network and a matrix power module which ensures equal sharing of power among individual amplifiers. This eliminates the loss of efficiency and increased mass when an amplifier associated with a beam must be over-designed to meet uncertainties in power distribution between beams. Flexibility in allocation of bandwidth to beams is achieved by intermediate frequency subdivision of the L-band service categories defined by ITU. These spectral subdivisions are assigned to beams by an IF interconnect matrix having beam ports and filter ports as inputs and outputs, respectively. Two such filter switch matrices are required, one for the inbound L-band to feeder link transponder, and one for the outbound feeder link to L-band transponder.

Improved minimum cost and maximum power two stage genome-wide association study designs.

PubMed

Stanhope, Stephen A; Skol, Andrew D

2012-01-01

In a two stage genome-wide association study (2S-GWAS), a sample of cases and controls is allocated into two groups, and genetic markers are analyzed sequentially with respect to these groups. For such studies, experimental design considerations have primarily focused on minimizing study cost as a function of the allocation of cases and controls to stages, subject to a constraint on the power to detect an associated marker. However, most treatments of this problem implicitly restrict the set of feasible designs to only those that allocate the same proportions of cases and controls to each stage. In this paper, we demonstrate that removing this restriction can improve the cost advantages demonstrated by previous 2S-GWAS designs by up to 40%. Additionally, we consider designs that maximize study power with respect to a cost constraint, and show that recalculated power maximizing designs can recover a substantial amount of the planned study power that might otherwise be lost if study funding is reduced. We provide open source software for calculating cost minimizing or power maximizing 2S-GWAS designs.

Prediction of light aircraft interior sound pressure level using the room equation

NASA Technical Reports Server (NTRS)

Atwal, M.; Bernhard, R.

1984-01-01

The room equation is investigated for predicting interior sound level. The method makes use of an acoustic power balance, by equating net power flow into the cabin volume to power dissipated within the cabin using the room equation. The sound power level transmitted through the panels was calculated by multiplying the measured space averaged transmitted intensity for each panel by its surface area. The sound pressure level was obtained by summing the mean square sound pressures radiated from each panel. The data obtained supported the room equation model in predicting the cabin interior sound pressure level.

Photonic-powered cable assembly

DOEpatents

Sanderson, Stephen N.; Appel, Titus James; Wrye, IV, Walter C.

2013-01-22

A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

Photonic-powered cable assembly

DOEpatents

Sanderson, Stephen N; Appel, Titus James; Wrye, IV, Walter C

2014-06-24

A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

An Approach for Transmission Loss and Cost Allocation by Loss Allocation Index and Co-operative Game Theory

NASA Astrophysics Data System (ADS)

Khan, Baseem; Agnihotri, Ganga; Mishra, Anuprita S.

2016-03-01

In the present work authors proposed a novel method for transmission loss and cost allocation to users (generators and loads). In the developed methodology transmission losses are allocated to users based on their usage of the transmission line. After usage allocation, particular loss allocation indices (PLAI) are evaluated for loads and generators. Also Cooperative game theory approach is applied for comparison of results. The proposed method is simple and easy to implement on the practical power system. Sample 6 bus and IEEE 14 bus system is used for showing the effectiveness of proposed method.

Dynamic Sensor Networks

DTIC Science & Technology

2004-03-01

turned off. SLEEP Set the timer for 30 seconds before scheduled transmit time, then sleep the processor. WAKE When timer trips, power up the processor...slots where none of its neighbors are schedule to transmit. This allows the sensor nodes to perform a simple power man- agement scheme that puts the...routing This simple case study highlights the following crucial observation: optimal traffic scheduling in energy constrained networks requires future

Guaranteeing synchronous message deadlines with the timed token medium access control protocol

NASA Technical Reports Server (NTRS)

Agrawal, Gopal; Chen, Baio; Zhao, Wei; Davari, Sadegh

1992-01-01

We study the problem of guaranteeing synchronous message deadlines in token ring networks where the timed token medium access control protocol is employed. Synchronous capacity, defined as the maximum time for which a node can transmit its synchronous messages every time it receives the token, is a key parameter in the control of synchronous message transmission. To ensure the transmission of synchronous messages before their deadlines, synchronous capacities must be properly allocated to individual nodes. We address the issue of appropriate allocation of the synchronous capacities. Several synchronous capacity allocation schemes are analyzed in terms of their ability to satisfy deadline constraints of synchronous messages. We show that an inappropriate allocation of the synchronous capacities could cause message deadlines to be missed even if the synchronous traffic is extremely low. We propose a scheme called the normalized proportional allocation scheme which can guarantee the synchronous message deadlines for synchronous traffic of up to 33 percent of available utilization. To date, no other synchronous capacity allocation scheme has been reported to achieve such substantial performance. Another major contribution of this paper is an extension to the previous work on the bounded token rotation time. We prove that the time elapsed between any consecutive visits to a particular node is bounded by upsilon TTRT, where TTRT is the target token rotation time set up at system initialization time. The previous result by Johnson and Sevcik is a special case where upsilon = 2. We use this result in the analysis of various synchronous allocation schemes. It can also be applied in other similar studies.

ETR, TRA642. BASEMENT SPACE ALLOCATION FOR EXPERIMENTERS CA. 1966, SOUTHEAST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR, TRA-642. BASEMENT SPACE ALLOCATION FOR EXPERIMENTERS CA. 1966, SOUTHEAST QUADRANT OF FLOOR. WESTINGHOUSE ATOMIC POWER DIVISION (WAPD) AND BETTIS ATOMIC POWER LABORATORY (BAPL) CONSUME MOST OF THE QUADRANT. PHILLIPS PETROLEUM COMPANY ETR-E-2256, 12/1966. INL INDEX NO. 532-0642-00-706-021256, REV. F. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

A new concept of space solar power satellite

NASA Astrophysics Data System (ADS)

Li, Xun; Duan, Baoyan; Song, Liwei; Yang, Yang; Zhang, Yiqun; Wang, Dongxu

2017-07-01

Space solar power satellite (SSPS) is a tremendous energy system that collects and converts solar power to electric power in space, and then transmits the electric power to earth wirelessly. In this paper, a novel SSPS concept based on ε-near-zero (ENZ) metamaterial is proposed. A spherical condenser made of ENZ metamaterial is developed, by using the refractive property of the ENZ metamaterial sunlight can be captured and redirected to its center. To make the geometric concentration ratio of the PV array reasonable, a hemispherical one located at the center is used to collect and convert the normal-incidence sunlight to DC power, then through a phased array transmitting antenna the DC power is beamed down to the rectenna on the ground. Detailed design of the proposed concept is presented.

Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel

PubMed Central

Sakin, Sayef Azad; Alamri, Atif; Tran, Nguyen H.

2017-01-01

Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies. PMID:29215591

Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel.

PubMed

Sakin, Sayef Azad; Razzaque, Md Abdur; Hassan, Mohammad Mehedi; Alamri, Atif; Tran, Nguyen H; Fortino, Giancarlo

2017-12-07

Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies.

Reducing power consumption during execution of an application on a plurality of compute nodes

DOEpatents

Archer, Charles J.; Blocksome, Michael A.; Peters, Amanda E.; Ratterman, Joseph D.; Smith, Brian E.

2013-09-10

Methods, apparatus, and products are disclosed for reducing power consumption during execution of an application on a plurality of compute nodes that include: powering up, during compute node initialization, only a portion of computer memory of the compute node, including configuring an operating system for the compute node in the powered up portion of computer memory; receiving, by the operating system, an instruction to load an application for execution; allocating, by the operating system, additional portions of computer memory to the application for use during execution; powering up the additional portions of computer memory allocated for use by the application during execution; and loading, by the operating system, the application into the powered up additional portions of computer memory.

Wireless power transfer electric vehicle supply equipment installation and validation tool

DOEpatents

Jones, Perry T.; Miller, John M.

2015-05-19

A transmit pad inspection device includes a magnetic coupling device, which includes an inductive circuit that is configured to magnetically couple to a primary circuit of a charging device in a transmit pad through an alternating current (AC) magnetic field. The inductive circuit functions as a secondary circuit for a set of magnetically coupled coils. The magnetic coupling device further includes a rectification circuit, and includes a controllable load bank or is configured to be connected to an external controllable load back. The transmit pad inspection device is configured to determine the efficiency of power transfer under various coupling conditions. In addition, the transmit pad inspection device can be configured to measure residual magnetic field and the frequency of the input current, and to determine whether the charging device has been installed properly.

The design and construction of a module to demonstrate a method for transmission of data from a medical implant

NASA Astrophysics Data System (ADS)

Morgan, I.; Benjamin, J. D.

1985-08-01

Methods of powering devices to which only ac contact can be made and receiving data transmitted back from them are described. Such devices include medical implants which communicate with the external environment via ultrasound or rf links. Two breadboard systems were built to demonstrate the techniques. In both the device is powered by picking up an ac input and rectifying it. A signal voltage detected by the device is encoded as a frequency, transmitted and decoded. In one case this is performed on a separate channel from that used to power the device. In the other only one channel is used for both signals, and data is transmitted by modulating the impedance presented by the device. The resulting modulation of the input signal is picked up by the external circuit and decoded.

Analysis of the Light Transmission Ability of Reinforcing Glass Fibers Used in Polymer Composites.

PubMed

Hegedűs, Gergely; Sarkadi, Tamás; Czigány, Tibor

2017-06-10

This goal of our research was to show that E-glass fiber bundles used for reinforcing composites can be enabled to transmit light in a common resin without any special preparation (without removing the sizing). The power of the transmitted light was measured and the attenuation coefficient, which characterizes the fiber bundle, was determined. Although the attenuation coefficient depends on temperature and the wavelength of the light, it is independent of the power of incident light, the quality of coupling, and the length of the specimen. The refractive index of commercially available transparent resins was measured and it was proved that a resin with a refractive index lower than that of the fiber can be used to make a composite whose fibers are capable of transmitting light. The effects of temperature, compression of the fibers, and the shape of fiber ends on the power of transmitted light were examined. The measurement of emitted light can provide information about the health of the fibers. This can be the basis of a simple health monitoring system in the case of general-purpose composite structures.

Analysis of the Light Transmission Ability of Reinforcing Glass Fibers Used in Polymer Composites

PubMed Central

Hegedűs, Gergely; Sarkadi, Tamás; Czigány, Tibor

2017-01-01

This goal of our research was to show that E-glass fiber bundles used for reinforcing composites can be enabled to transmit light in a common resin without any special preparation (without removing the sizing). The power of the transmitted light was measured and the attenuation coefficient, which characterizes the fiber bundle, was determined. Although the attenuation coefficient depends on temperature and the wavelength of the light, it is independent of the power of incident light, the quality of coupling, and the length of the specimen. The refractive index of commercially available transparent resins was measured and it was proved that a resin with a refractive index lower than that of the fiber can be used to make a composite whose fibers are capable of transmitting light. The effects of temperature, compression of the fibers, and the shape of fiber ends on the power of transmitted light were examined. The measurement of emitted light can provide information about the health of the fibers. This can be the basis of a simple health monitoring system in the case of general-purpose composite structures. PMID:28772996

Triboelectric Nanogenerator as a Self-Powered Communication Unit for Processing and Transmitting Information.

PubMed

Yu, Aifang; Chen, Xiangyu; Wang, Rui; Liu, Jingyu; Luo, Jianjun; Chen, Libo; Zhang, Yang; Wu, Wei; Liu, Caihong; Yuan, Hongtao; Peng, Mingzeng; Hu, Weiguo; Zhai, Junyi; Wang, Zhong Lin

2016-04-26

In this paper, we demonstrate an application of a triboelectric nanogenerator (TENG) as a self-powered communication unit. An elaborately designed TENG is used to translate a series of environmental triggering signals into binary digital signals and drives an electronic-optical device to transmit binary digital data in real-time without an external power supply. The elaborately designed TENG is built in a membrane structure that can effectively drive the electronic-optical device in a bandwidth from 1.30 to 1.65 kHz. Two typical communication modes (amplitude-shift keying and frequency-shift keying) are realized through the resonant response of TENG to different frequencies, and two digital signals, i.e., "1001" and "0110", are successfully transmitted and received through this system, respectively. Hence, in this study, a simple but efficient method for directly transmitting ambient vibration to the receiver as a digital signal is established using an elaborately designed TENG and an optical communication technique. This type of the communication system, as well as the implementation method presented, exhibits great potential for applications in the smart city, smart home, password authentication, and so on.

Theater Combat Search and Rescue

DTIC Science & Technology

1993-05-06

response to crises requiring the use of military forces. Theater CINCs receive mission taskings through a warning order transmitted from 5 0 the Joint...Chiefs of Staff. This warning order allocates specific military forces that CINCs may use when planning various courses of action. The CINCs complete and...consists of the President and the 5 Secretary of Defense, and is the only approving authority to order execution of a military action. 10 Deliberate

Some dynamic resource allocation problems in wireless networks

NASA Astrophysics Data System (ADS)

Berry, Randall

2001-07-01

We consider dynamic resource allocation problems that arise in wireless networking. Specifically transmission scheduling problems are studied in cases where a user can dynamically allocate communication resources such as transmission rate and power based on current channel knowledge as well as traffic variations. We assume that arriving data is stored in a transmission buffer, and investigate the trade-off between average transmission power and average buffer delay. A general characterization of this trade-off is given and the behavior of this trade-off in the regime of asymptotically large buffer delays is explored. An extension to a more general utility based quality of service definition is also discussed.

Transmit coil design for Wireless Power Transfer for medical implants.

PubMed

Lemdiasov, Rosti; Venkatasubramanian, Arun

2017-07-01

A new design approach for the design of transmit coils for Wireless Power Transfer (WPT) is presented. The theoretical formulation involves a figure of merit that has to be maximized to solve for the surface current. Numerical predictions and comparisons with practical measurements for the coil parameters (inductance. resistance) underscore the success of this approach in terms of achieving strong coupling with a receive coil while maintaining low resistance.

Toward allocative efficiency in the prescription drug industry.

PubMed

Guell, R C; Fischbaum, M

1995-01-01

Traditionally, monopoly power in the pharmaceutical industry has been measured by profits. An alternative method estimates the deadweight loss of consumer surplus associated with the exercise of monopoly power. Although upper and lower bound estimates for this inefficiency are far apart, they at least suggest a dramatically greater welfare loss than measures of industry profitability would imply. A proposed system would have the U.S. government employing its power of eminent domain to "take" and distribute pharmaceutical patents, providing as "just compensation" the present value of the patent's expected future monopoly profits. Given the allocative inefficiency of raising taxes to pay for the program, the impact of the proposal on allocative efficiency would be at least as good at our lower bound estimate of monopoly costs while substantially improving efficiency at or near our upper bound estimate.

Metro-access integrated network based on optical OFDMA with dynamic sub-carrier allocation and power distribution.

PubMed

Zhang, Chongfu; Zhang, Qiongli; Chen, Chen; Jiang, Ning; Liu, Deming; Qiu, Kun; Liu, Shuang; Wu, Baojian

2013-01-28

We propose and demonstrate a novel optical orthogonal frequency-division multiple access (OFDMA)-based metro-access integrated network with dynamic resource allocation. It consists of a single fiber OFDMA ring and many single fiber OFDMA trees, which transparently integrates metropolitan area networks with optical access networks. The single fiber OFDMA ring connects the core network and the central nodes (CNs), the CNs are on demand reconfigurable and use multiple orthogonal sub-carriers to realize parallel data transmission and dynamic resource allocation, meanwhile, they can also implement flexible power distribution. The remote nodes (RNs) distributed in the user side are connected by the single fiber OFDMA trees with the corresponding CN. The obtained results indicate that our proposed metro-access integrated network is feasible and the power distribution is agile.

Efficient Pricing Technique for Resource Allocation Problem in Downlink OFDM Cognitive Radio Networks

NASA Astrophysics Data System (ADS)

Abdulghafoor, O. B.; Shaat, M. M. R.; Ismail, M.; Nordin, R.; Yuwono, T.; Alwahedy, O. N. A.

2017-05-01

In this paper, the problem of resource allocation in OFDM-based downlink cognitive radio (CR) networks has been proposed. The purpose of this research is to decrease the computational complexity of the resource allocation algorithm for downlink CR network while concerning the interference constraint of primary network. The objective has been secured by adopting pricing scheme to develop power allocation algorithm with the following concerns: (i) reducing the complexity of the proposed algorithm and (ii) providing firm power control to the interference introduced to primary users (PUs). The performance of the proposed algorithm is tested for OFDM- CRNs. The simulation results show that the performance of the proposed algorithm approached the performance of the optimal algorithm at a lower computational complexity, i.e., O(NlogN), which makes the proposed algorithm suitable for more practical applications.

Less power or powerless? Egocentric empathy gaps and the irony of having little versus no power in social decision making.

PubMed

Handgraaf, Michel J J; Van Dijk, Eric; Vermunt, Riël C; Wilke, Henk A M; De Dreu, Carsten K W

2008-11-01

The authors investigate the effect of power differences and associated expectations in social decision making. Using a modified ultimatum game, the authors show that allocators lower their offers to recipients when the power difference shifts in favor of the allocator. Remarkably, however, when recipients are completely powerless, offers increase. This effect is mediated by a change in framing of the situation: When the opponent is without power, feelings of social responsibility are evoked. On the recipient side, the authors show that recipients do not anticipate these higher outcomes resulting from powerlessness. They prefer more power over less, expecting higher outcomes when they are more powerful, especially when less power entails powerlessness. Results are discussed in relation to empathy gaps and social responsibility. (c) 2008 APA, all rights reserved.

Allocation and management issues in multiple-transaction open access transmission networks

NASA Astrophysics Data System (ADS)

Tao, Shu

This thesis focuses on some key issues related to allocation and management by the independent grid operator (IGO) of unbundled services in multiple-transaction open access transmission networks. The three unbundled services addressed in the thesis are transmission real power losses, reactive power support requirements from generation sources, and transmission congestion management. We develop the general framework that explicitly represents multiple transactions undertaken simultaneously in the transmission grid. This framework serves as the basis for formulating various problems treated in the thesis. We use this comprehensive framework to develop a physical-flow-based mechanism to allocate the total transmission losses to each transaction using the system. An important property of the allocation scheme is its capability to effectively deal with counter flows that result in the presence of specific transactions. Using the loss allocation results as the basis, we construct the equivalent loss compensation concept and apply it to develop flexible and effective procedures for compensating losses in multiple-transaction networks. We present a new physical-flow-based mechanism for allocating the reactive power support requirements provided by generators in multiple-transaction networks. The allocatable reactive support requirements are formulated as the sum of two specific components---the voltage magnitude variation component and the voltage angle variation component. The formulation utilizes the multiple-transaction framework and makes use of certain simplifying approximations. The formulation leads to a natural allocation as a function of the amount of each transaction. The physical interpretation of each allocation as a sensitivity of the reactive output of a generator is discussed. We propose a congestion management allocation scheme for multiple-transaction networks. The proposed scheme determines the allocation of congestion among the transactions on a physical-flow basis. It also proposes a congestion relief scheme that removes the congestion attributed to each transaction on the network in a least-cost manner to the IGO and determines the appropriate transmission charges to each transaction for its transmission usage. The thesis provides a compendium of problems that are natural extensions of the research results reported here and appear to be good candidates for future work.

Flexible operation strategy for environment control system in abnormal supply power condition

NASA Astrophysics Data System (ADS)

Liping, Pang; Guoxiang, Li; Hongquan, Qu; Yufeng, Fang

2017-04-01

This paper establishes an optimization method that can be applied to the flexible operation of the environment control system in an abnormal supply power condition. A proposed conception of lifespan is used to evaluate the depletion time of the non-regenerative substance. The optimization objective function is to maximize the lifespans. The optimization variables are the allocated powers of subsystems. The improved Non-dominated Sorting Genetic Algorithm is adopted to obtain the pareto optimization frontier with the constraints of the cabin environmental parameters and the adjustable operating parameters of the subsystems. Based on the same importance of objective functions, the preferred power allocation of subsystems can be optimized. Then the corresponding running parameters of subsystems can be determined to ensure the maximum lifespans. A long-duration space station with three astronauts is used to show the implementation of the proposed optimization method. Three different CO2 partial pressure levels are taken into consideration in this study. The optimization results show that the proposed optimization method can obtain the preferred power allocation for the subsystems when the supply power is at a less-than-nominal value. The method can be applied to the autonomous control for the emergency response of the environment control system.

Two essays on efficiency in the electric power industry: Measurement of technical and allocative efficiency

NASA Astrophysics Data System (ADS)

Gardiner, John Corby

The electric power industry market structure has changed over the last twenty years since the passage of the Public Utility Regulatory Policies Act (PURPA). These changes include the entry by unregulated generator plants and, more recently, the deregulation of entry and price in the retail generation market. Such changes have introduced and expanded competitive forces on the incumbent electric power plants. Proponents of this deregulation argued that the enhanced competition would lead to a more efficient allocation of resources. Previous studies of power plant technical and allocative efficiency have failed to measure technical and allocative efficiency at the plant level. In contrast, this study uses panel data on 35 power plants over 59 years to estimate technical and allocative efficiency of each plant. By using a flexible functional form, which is not constrained by the assumption that regulation is constant over the 59 years sampled, the estimation procedure accounts for changes in both state and national regulatory/energy policies that may have occurred over the sample period. The empirical evidence presented shows that most of the power plants examined have operated more efficiently since the passage of PURPA and the resultant increase of competitive forces. Chapter 2 extends the model used in Chapter 1 and clarifies some issues in the efficiency literature by addressing the case where homogeneity does not hold. A more general model is developed for estimating both input and output inefficiency simultaneously. This approach reveals more information about firm inefficiency than the single estimation approach that has previously been used in the literature. Using the more general model, estimates are provided on the type of inefficiency that occurs as well as the cost of inefficiency by type of inefficiency. In previous studies, the ranking of firms by inefficiency has been difficult because of the cardinal and ordinal differences between different types of inefficiency estimates. However, using the general approach, this study illustrates that plants can be ranked by overall efficiency.

The Conference Proceedings of the 1997 Air Transport Research Group (ATRG) of the WCTR Society. Volume 3

NASA Technical Reports Server (NTRS)

Oum, T. H.; Bowen, B. D.

1997-01-01

This paper covers topics such as: Safety and Air Fares; International Airline Safety; Multi-fare Seat Allocation Problem; Dynamic Allocation of Airline Seat Inventory; Seat Allocation on Flights with Two Fares; Effects of Intercontinental Alliances; Domestic Airline Mergers; Simulating the Effects of Airline Deregulation on Frequency Choice; and Firm Size Inequality and Market Power.

Throughput assurance of wireless body area networks coexistence based on stochastic geometry

PubMed Central

Wang, Yinglong; Shu, Minglei; Wu, Shangbin

2017-01-01

Wireless body area networks (WBANs) are expected to influence the traditional medical model by assisting caretakers with health telemonitoring. Within WBANs, the transmit power of the nodes should be as small as possible owing to their limited energy capacity but should be sufficiently large to guarantee the quality of the signal at the receiving nodes. When multiple WBANs coexist in a small area, the communication reliability and overall throughput can be seriously affected due to resource competition and interference. We show that the total network throughput largely depends on the WBANs distribution density (λp), transmit power of their nodes (Pt), and their carrier-sensing threshold (γ). Using stochastic geometry, a joint carrier-sensing threshold and power control strategy is proposed to meet the demand of coexisting WBANs based on the IEEE 802.15.4 standard. Given different network distributions and carrier-sensing thresholds, the proposed strategy derives a minimum transmit power according to varying surrounding environment. We obtain expressions for transmission success probability and throughput adopting this strategy. Using numerical examples, we show that joint carrier-sensing thresholds and transmit power strategy can effectively improve the overall system throughput and reduce interference. Additionally, this paper studies the effects of a guard zone on the throughput using a Matern hard-core point process (HCPP) type II model. Theoretical analysis and simulation results show that the HCPP model can increase the success probability and throughput of networks. PMID:28141841

Wireless power delivery for retinal prostheses.

PubMed

Ng, David C; Williams, Chris E; Allen, Penny J; Bai, Shun; Boyd, Clive S; Meffin, Hamish; Halpern, Mark E; Skafidas, Efstratios

2011-01-01

Delivering power to an implanted device located deep inside the body is not trivial. This problem is made more challenging if the implanted device is in constant motion. This paper describes two methods of transferring power wirelessly by means of magnetic induction coupling. In the first method, a pair of transmit and receive coils is used for power transfer over a large distance (compared to their diameter). In the second method, an intermediate pair of coils is inserted in between transmit and receive coils. Comparison between the power transfer efficiency with and without the intermediate coils shows power transfer efficiency to be 11.5 % and 8.8 %, respectively. The latter method is especially suitable for powering implanted devices in the eye due to immunity to movements of the eye and ease of surgery. Using this method, we have demonstrated wireless power delivery into an animal eye.

Allocating HIV prevention funds in the United States: recommendations from an optimization model.

PubMed

Lasry, Arielle; Sansom, Stephanie L; Hicks, Katherine A; Uzunangelov, Vladislav

2012-01-01

The Centers for Disease Control and Prevention (CDC) had an annual budget of approximately $327 million to fund health departments and community-based organizations for core HIV testing and prevention programs domestically between 2001 and 2006. Annual HIV incidence has been relatively stable since the year 2000 and was estimated at 48,600 cases in 2006 and 48,100 in 2009. Using estimates on HIV incidence, prevalence, prevention program costs and benefits, and current spending, we created an HIV resource allocation model that can generate a mathematically optimal allocation of the Division of HIV/AIDS Prevention's extramural budget for HIV testing, and counseling and education programs. The model's data inputs and methods were reviewed by subject matter experts internal and external to the CDC via an extensive validation process. The model projects the HIV epidemic for the United States under different allocation strategies under a fixed budget. Our objective is to support national HIV prevention planning efforts and inform the decision-making process for HIV resource allocation. Model results can be summarized into three main recommendations. First, more funds should be allocated to testing and these should further target men who have sex with men and injecting drug users. Second, counseling and education interventions ought to provide a greater focus on HIV positive persons who are aware of their status. And lastly, interventions should target those at high risk for transmitting or acquiring HIV, rather than lower-risk members of the general population. The main conclusions of the HIV resource allocation model have played a role in the introduction of new programs and provide valuable guidance to target resources and improve the impact of HIV prevention efforts in the United States.

Spectrum sensing and resource allocation for multicarrier cognitive radio systems under interference and power constraints

NASA Astrophysics Data System (ADS)

Dikmese, Sener; Srinivasan, Sudharsan; Shaat, Musbah; Bader, Faouzi; Renfors, Markku

2014-12-01

Multicarrier waveforms have been commonly recognized as strong candidates for cognitive radio. In this paper, we study the dynamics of spectrum sensing and spectrum allocation functions in cognitive radio context using very practical signal models for the primary users (PUs), including the effects of power amplifier nonlinearities. We start by sensing the spectrum with energy detection-based wideband multichannel spectrum sensing algorithm and continue by investigating optimal resource allocation methods. Along the way, we examine the effects of spectral regrowth due to the inevitable power amplifier nonlinearities of the PU transmitters. The signal model includes frequency selective block-fading channel models for both secondary and primary transmissions. Filter bank-based wideband spectrum sensing techniques are applied for detecting spectral holes and filter bank-based multicarrier (FBMC) modulation is selected for transmission as an alternative multicarrier waveform to avoid the disadvantage of limited spectral containment of orthogonal frequency-division multiplexing (OFDM)-based multicarrier systems. The optimization technique used for the resource allocation approach considered in this study utilizes the information obtained through spectrum sensing and knowledge of spectrum leakage effects of the underlying waveforms, including a practical power amplifier model for the PU transmitter. This study utilizes a computationally efficient algorithm to maximize the SU link capacity with power and interference constraints. It is seen that the SU transmission capacity depends critically on the spectral containment of the PU waveform, and these effects are quantified in a case study using an 802.11-g WLAN scenario.

Optimal Power Allocation Strategy in a Joint Bistatic Radar and Communication System Based on Low Probability of Intercept

PubMed Central

Wang, Fei; Salous, Sana; Zhou, Jianjiang

2017-01-01

In this paper, we investigate a low probability of intercept (LPI)-based optimal power allocation strategy for a joint bistatic radar and communication system, which is composed of a dedicated transmitter, a radar receiver, and a communication receiver. The joint system is capable of fulfilling the requirements of both radar and communications simultaneously. First, assuming that the signal-to-noise ratio (SNR) corresponding to the target surveillance path is much weaker than that corresponding to the line of sight path at radar receiver, the analytically closed-form expression for the probability of false alarm is calculated, whereas the closed-form expression for the probability of detection is not analytically tractable and is approximated due to the fact that the received signals are not zero-mean Gaussian under target presence hypothesis. Then, an LPI-based optimal power allocation strategy is presented to minimize the total transmission power for information signal and radar waveform, which is constrained by a specified information rate for the communication receiver and the desired probabilities of detection and false alarm for the radar receiver. The well-known bisection search method is employed to solve the resulting constrained optimization problem. Finally, numerical simulations are provided to reveal the effects of several system parameters on the power allocation results. It is also demonstrated that the LPI performance of the joint bistatic radar and communication system can be markedly improved by utilizing the proposed scheme. PMID:29186850

Optimal Power Allocation Strategy in a Joint Bistatic Radar and Communication System Based on Low Probability of Intercept.

PubMed

Shi, Chenguang; Wang, Fei; Salous, Sana; Zhou, Jianjiang

2017-11-25

In this paper, we investigate a low probability of intercept (LPI)-based optimal power allocation strategy for a joint bistatic radar and communication system, which is composed of a dedicated transmitter, a radar receiver, and a communication receiver. The joint system is capable of fulfilling the requirements of both radar and communications simultaneously. First, assuming that the signal-to-noise ratio (SNR) corresponding to the target surveillance path is much weaker than that corresponding to the line of sight path at radar receiver, the analytically closed-form expression for the probability of false alarm is calculated, whereas the closed-form expression for the probability of detection is not analytically tractable and is approximated due to the fact that the received signals are not zero-mean Gaussian under target presence hypothesis. Then, an LPI-based optimal power allocation strategy is presented to minimize the total transmission power for information signal and radar waveform, which is constrained by a specified information rate for the communication receiver and the desired probabilities of detection and false alarm for the radar receiver. The well-known bisection search method is employed to solve the resulting constrained optimization problem. Finally, numerical simulations are provided to reveal the effects of several system parameters on the power allocation results. It is also demonstrated that the LPI performance of the joint bistatic radar and communication system can be markedly improved by utilizing the proposed scheme.

Optimal Sensor Allocation for Fault Detection and Isolation

NASA Technical Reports Server (NTRS)

Azam, Mohammad; Pattipati, Krishna; Patterson-Hine, Ann

2004-01-01

Automatic fault diagnostic schemes rely on various types of sensors (e.g., temperature, pressure, vibration, etc) to measure the system parameters. Efficacy of a diagnostic scheme is largely dependent on the amount and quality of information available from these sensors. The reliability of sensors, as well as the weight, volume, power, and cost constraints, often makes it impractical to monitor a large number of system parameters. An optimized sensor allocation that maximizes the fault diagnosibility, subject to specified weight, volume, power, and cost constraints is required. Use of optimal sensor allocation strategies during the design phase can ensure better diagnostics at a reduced cost for a system incorporating a high degree of built-in testing. In this paper, we propose an approach that employs multiple fault diagnosis (MFD) and optimization techniques for optimal sensor placement for fault detection and isolation (FDI) in complex systems. Keywords: sensor allocation, multiple fault diagnosis, Lagrangian relaxation, approximate belief revision, multidimensional knapsack problem.

Two‐phase designs for joint quantitative‐trait‐dependent and genotype‐dependent sampling in post‐GWAS regional sequencing

PubMed Central

Espin‐Garcia, Osvaldo; Craiu, Radu V.

2017-01-01

ABSTRACT We evaluate two‐phase designs to follow‐up findings from genome‐wide association study (GWAS) when the cost of regional sequencing in the entire cohort is prohibitive. We develop novel expectation‐maximization‐based inference under a semiparametric maximum likelihood formulation tailored for post‐GWAS inference. A GWAS‐SNP (where SNP is single nucleotide polymorphism) serves as a surrogate covariate in inferring association between a sequence variant and a normally distributed quantitative trait (QT). We assess test validity and quantify efficiency and power of joint QT‐SNP‐dependent sampling and analysis under alternative sample allocations by simulations. Joint allocation balanced on SNP genotype and extreme‐QT strata yields significant power improvements compared to marginal QT‐ or SNP‐based allocations. We illustrate the proposed method and evaluate the sensitivity of sample allocation to sampling variation using data from a sequencing study of systolic blood pressure. PMID:29239496

An Economic Analysis of Two Groundwater Allocation Programs for the Salinas Valley

DTIC Science & Technology

1994-06-01

monitoring system would establish a definable and 17Each individual well would have a frequency generator, analog/ digital converter, microprocessor with...RTU). The cost for purchasing and installing the frequency generator is estimated to be $1,100. The RTU consists of an analog/ digital converter and a...programmable microprocessor that can accept up to eight inputs and one output. The unit can transmit and receive digital data via LAN network or

Downhole drilling network using burst modulation techniques

DOEpatents

Hall,; David R. , Fox; Joe, [Spanish Fork, UT

2007-04-03

A downhole drilling system is disclosed in one aspect of the present invention as including a drill string and a transmission line integrated into the drill string. Multiple network nodes are installed at selected intervals along the drill string and are adapted to communicate with one another through the transmission line. In order to efficiently allocate the available bandwidth, the network nodes are configured to use any of numerous burst modulation techniques to transmit data.

77 FR 35671 - Conformed Power Marketing Criteria or Regulations for the Boulder Canyon Project

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-14

... DEPARTMENT OF ENERGY Western Area Power Administration Conformed Power Marketing Criteria or... of power marketing criteria in accordance with the Hoover Power Allocation Act of 2011. SUMMARY: The Western Area Power Administration (Western), a Federal power marketing agency of the Department of Energy...

Passenger Transmitters as A Possible Cause of Aircraft Fuel Ignition

NASA Technical Reports Server (NTRS)

Nguyen, Truong X.; Ely, Jay J.; Dudley, Kenneth L.; Scearce, Stephen A.; Hatfield, Michael O.; Richardson, Robert E.

2006-01-01

An investigation was performed to study the potential for radio frequency (RF) power radiated from transmitting Portable Electronic Devices (PEDs) to create an arcing/sparking event within the fuel tank of a large transport aircraft. A survey of RF emissions from typical intentional transmitting PEDs was first performed. Aircraft measurements of RF coupling to the fuel tank and its wiring were also performed to determine the PEDs induced power on the wiring, and the re-radiated power within the fuel tank. Laboratory simulations were conducted to determine the required RF power level for an arcing/sparking event. Data analysis shows large positive safety margins, even with simulated faults on the wiring.

10 CFR 205.305 - Transferability.

Code of Federal Regulations, 2010 CFR

2010-01-01

... OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System Permits and Reports; Applications; Administrative Procedures and Sanctions Application for Authorization to Transmit Electric Energy to A Foreign Country § 205.305 Transferability. (a) An authorization to transmit electric energy from...

10 CFR 205.305 - Transferability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System Permits and Reports; Applications; Administrative Procedures and Sanctions Application for Authorization to Transmit Electric Energy to A Foreign Country § 205.305 Transferability. (a) An authorization to transmit electric energy from...

Worst-Case Energy Efficiency Maximization in a 5G Massive MIMO-NOMA System.

PubMed

Chinnadurai, Sunil; Selvaprabhu, Poongundran; Jeong, Yongchae; Jiang, Xueqin; Lee, Moon Ho

2017-09-18

In this paper, we examine the robust beamforming design to tackle the energy efficiency (EE) maximization problem in a 5G massive multiple-input multiple-output (MIMO)-non-orthogonal multiple access (NOMA) downlink system with imperfect channel state information (CSI) at the base station. A novel joint user pairing and dynamic power allocation (JUPDPA) algorithm is proposed to minimize the inter user interference and also to enhance the fairness between the users. This work assumes imperfect CSI by adding uncertainties to channel matrices with worst-case model, i.e., ellipsoidal uncertainty model (EUM). A fractional non-convex optimization problem is formulated to maximize the EE subject to the transmit power constraints and the minimum rate requirement for the cell edge user. The designed problem is difficult to solve due to its nonlinear fractional objective function. We firstly employ the properties of fractional programming to transform the non-convex problem into its equivalent parametric form. Then, an efficient iterative algorithm is proposed established on the constrained concave-convex procedure (CCCP) that solves and achieves convergence to a stationary point of the above problem. Finally, Dinkelbach's algorithm is employed to determine the maximum energy efficiency. Comprehensive numerical results illustrate that the proposed scheme attains higher worst-case energy efficiency as compared with the existing NOMA schemes and the conventional orthogonal multiple access (OMA) scheme.

Worst-Case Energy Efficiency Maximization in a 5G Massive MIMO-NOMA System

PubMed Central

Jeong, Yongchae; Jiang, Xueqin; Lee, Moon Ho

2017-01-01

In this paper, we examine the robust beamforming design to tackle the energy efficiency (EE) maximization problem in a 5G massive multiple-input multiple-output (MIMO)-non-orthogonal multiple access (NOMA) downlink system with imperfect channel state information (CSI) at the base station. A novel joint user pairing and dynamic power allocation (JUPDPA) algorithm is proposed to minimize the inter user interference and also to enhance the fairness between the users. This work assumes imperfect CSI by adding uncertainties to channel matrices with worst-case model, i.e., ellipsoidal uncertainty model (EUM). A fractional non-convex optimization problem is formulated to maximize the EE subject to the transmit power constraints and the minimum rate requirement for the cell edge user. The designed problem is difficult to solve due to its nonlinear fractional objective function. We firstly employ the properties of fractional programming to transform the non-convex problem into its equivalent parametric form. Then, an efficient iterative algorithm is proposed established on the constrained concave-convex procedure (CCCP) that solves and achieves convergence to a stationary point of the above problem. Finally, Dinkelbach’s algorithm is employed to determine the maximum energy efficiency. Comprehensive numerical results illustrate that the proposed scheme attains higher worst-case energy efficiency as compared with the existing NOMA schemes and the conventional orthogonal multiple access (OMA) scheme. PMID:28927019

Efficacy of an adapted HIV and sexually transmitted infection prevention intervention for incarcerated women: a randomized controlled trial.

PubMed

Fogel, Catherine I; Crandell, Jamie L; Neevel, A M; Parker, Sharon D; Carry, Monique; White, Becky L; Fasula, Amy M; Herbst, Jeffrey H; Gelaude, Deborah J

2015-04-01

We tested the efficacy of an adapted evidence-based HIV-sexually transmitted infection (STI) behavioral intervention (Providing Opportunities for Women's Empowerment, Risk-Reduction, and Relationships, or POWER) among incarcerated women. We conducted a randomized trial with 521 women aged 18 to 60 years in 2 correctional facilities in North Carolina in 2010 and 2011. Intervention participants attended 8 POWER sessions; control participants received a single standard-of-care STI prevention session. We followed up at 3 and 6 months after release. We examined intervention efficacy with mixed-effects models. POWER participants reported fewer male sexual partners than did control participants at 3 months, although this finding did not reach statistical significance; at 6 months they reported significantly less vaginal intercourse without a condom outside of a monogamous relationship and more condom use with a main male partner. POWER participants also reported significantly fewer condom barriers, and greater HIV knowledge, health-protective communication, and tangible social support. The intervention had no significant effects on incident STIs. POWER is a behavioral intervention with potential to reduce risk of acquiring or transmitting HIV and STIs among incarcerated women returning to their communities.

Efficacy of an Adapted HIV and Sexually Transmitted Infection Prevention Intervention for Incarcerated Women: A Randomized Controlled Trial

PubMed Central

Crandell, Jamie L.; Neevel, A. M.; Parker, Sharon D.; Carry, Monique; White, Becky L.; Fasula, Amy M.; Herbst, Jeffrey H.; Gelaude, Deborah J.

2015-01-01

Objectives. We tested the efficacy of an adapted evidence-based HIV–sexually transmitted infection (STI) behavioral intervention (Providing Opportunities for Women’s Empowerment, Risk-Reduction, and Relationships, or POWER) among incarcerated women. Methods. We conducted a randomized trial with 521 women aged 18 to 60 years in 2 correctional facilities in North Carolina in 2010 and 2011. Intervention participants attended 8 POWER sessions; control participants received a single standard-of-care STI prevention session. We followed up at 3 and 6 months after release. We examined intervention efficacy with mixed-effects models. Results. POWER participants reported fewer male sexual partners than did control participants at 3 months, although this finding did not reach statistical significance; at 6 months they reported significantly less vaginal intercourse without a condom outside of a monogamous relationship and more condom use with a main male partner. POWER participants also reported significantly fewer condom barriers, and greater HIV knowledge, health-protective communication, and tangible social support. The intervention had no significant effects on incident STIs. Conclusions. POWER is a behavioral intervention with potential to reduce risk of acquiring or transmitting HIV and STIs among incarcerated women returning to their communities. PMID:25211714

Quasistatic Cavity Resonance for Ubiquitous Wireless Power Transfer.

PubMed

Chabalko, Matthew J; Shahmohammadi, Mohsen; Sample, Alanson P

2017-01-01

Wireless power delivery has the potential to seamlessly power our electrical devices as easily as data is transmitted through the air. However, existing solutions are limited to near contact distances and do not provide the geometric freedom to enable automatic and un-aided charging. We introduce quasistatic cavity resonance (QSCR), which can enable purpose-built structures, such as cabinets, rooms, and warehouses, to generate quasistatic magnetic fields that safely deliver kilowatts of power to mobile receivers contained nearly anywhere within. A theoretical model of a quasistatic cavity resonator is derived, and field distributions along with power transfer efficiency are validated against measured results. An experimental demonstration shows that a 54 m3 QSCR room can deliver power to small coil receivers in nearly any position with 40% to 95% efficiency. Finally, a detailed safety analysis shows that up to 1900 watts can be transmitted to a coil receiver enabling safe and ubiquitous wireless power.

Quasistatic Cavity Resonance for Ubiquitous Wireless Power Transfer

PubMed Central

Shahmohammadi, Mohsen; Sample, Alanson P.

2017-01-01

Wireless power delivery has the potential to seamlessly power our electrical devices as easily as data is transmitted through the air. However, existing solutions are limited to near contact distances and do not provide the geometric freedom to enable automatic and un-aided charging. We introduce quasistatic cavity resonance (QSCR), which can enable purpose-built structures, such as cabinets, rooms, and warehouses, to generate quasistatic magnetic fields that safely deliver kilowatts of power to mobile receivers contained nearly anywhere within. A theoretical model of a quasistatic cavity resonator is derived, and field distributions along with power transfer efficiency are validated against measured results. An experimental demonstration shows that a 54 m3 QSCR room can deliver power to small coil receivers in nearly any position with 40% to 95% efficiency. Finally, a detailed safety analysis shows that up to 1900 watts can be transmitted to a coil receiver enabling safe and ubiquitous wireless power. PMID:28199321

Optical Power Transfer System for Powering a Remote Mobility System for Multiple Missions

NASA Technical Reports Server (NTRS)

Hogan, Bartholomew P. (Inventor); Stone, William C. (Inventor)

2016-01-01

An optical power transfer system for powering a remote mobility system for multiple missions comprising a high power source and a chilling station connected to a laser source. The laser source transmits a high optical energy to a beam switch assembly via an optical fiber. The beam switch assembly is optically connected to actively cooled fiber spoolers. Docking stations are adapted for securing the fiber spoolers until alternatively ready for use by a remote mobility system. The remote mobility system is optically connected to the fiber spoolers and has a receiving port adapted for securing the fiber spoolers thereon. The fiber spooler transmits the optical energy to a power conversion system which converts the optical energy received to another usable form of energy. More than one power source may be used where the remote mobility system transfers from one source to another while maintaining an operational radius to each source.

Mathematical analysis and coordinated current allocation control in battery power module systems

NASA Astrophysics Data System (ADS)

Han, Weiji; Zhang, Liang

2017-12-01

As the major energy storage device and power supply source in numerous energy applications, such as solar panels, wind plants, and electric vehicles, battery systems often face the issue of charge imbalance among battery cells/modules, which can accelerate battery degradation, cause more energy loss, and even incur fire hazard. To tackle this issue, various circuit designs have been developed to enable charge equalization among battery cells/modules. Recently, the battery power module (BPM) design has emerged to be one of the promising solutions for its capability of independent control of individual battery cells/modules. In this paper, we propose a new current allocation method based on charging/discharging space (CDS) for performance control in BPM systems. Based on the proposed method, the properties of CDS-based current allocation with constant parameters are analyzed. Then, real-time external total power requirement is taken into account and an algorithm is developed for coordinated system performance control. By choosing appropriate control parameters, the desired system performance can be achieved by coordinating the module charge balance and total power efficiency. Besides, the proposed algorithm has complete analytical solutions, and thus is very computationally efficient. Finally, the efficacy of the proposed algorithm is demonstrated using simulations.

Safe delivery of optical power from space.

PubMed

Smith, M; Fork, R L; Cole, S

2001-05-07

More than a billion gigawatts of sunlight pass through the area extending from Earth out to geostationary orbit. A small fraction of this clean renewable power appears more than adequate to satisfy the projected needs of Earth, and of human exploration and development of space far into the future. Recent studies suggest safe and efficient access to this power can be achieved within 10 to 40 years. Light, enhanced in spatial and temporal coherence, as compared to natural sunlight, offers a means, and probably the only practical means, of usefully transmitting this power to Earth. We describe safety standards for satellite constellations and Earth based sites designed, respectively, to transmit, and receive this power. The spectral properties, number of satellites, and angle subtended at Earth that are required for safe delivery are identified and discussed.

A novel high-speed PLC communication modem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abraham, K.C.; Roy, S.

1992-10-01

In this paper an innovative design for power line carrier (PLC) communication using digitally modulated signals is presented. The major contribution consists of a new signal coupler to the power line that achieves a stable transmission bandwidth of 4 KHz on distribution lines over long distances. Preliminary field tests achieved half-duplex operation at 1.2 Kbaud over a distribution power line to the 120V network and back with a symbol error rate of about 2% using less than about 10 W of average transmitted power, which is considerably superior to the present state-of-the-art PLC modems. Full-duplex operation over 120/240V intra-building wiringmore » has also been field tested at 9.6 Kbaud over distances of 3000 ft. using 1W of average transmitted power.« less

Spectral variation of high power microwave pulse propagating in a self-generated plasma

NASA Technical Reports Server (NTRS)

Ren, A.; Kuo, S. P.; Kossey, Paul

1995-01-01

A systematic study to understand the spectral variation of a high power microwave pulse propagating in a self-generated plasma is carried out. It includes the theoretical formulation, experimental demonstration, and computer simulations and computer experiments. The experiment of pulse propagation is conducted in a vacuum chamber filled with dry air (approximately 0.2 torr); the chamber is made of a 2 ft. cube of Plexiglas. A rectangular microwave pulse (1 microsec pulse width and 3.27 GHz carrier frequency) is fed into the cube through an S band microwave horn placed at one side of the chamber. A second S-band horn placed at the opposite side of the chamber is used to receive the transmitted pulse. The spectra of the incident pulse and transmitted pulse are then compared. As the power of the incident pulse is only slightly (less than 15%) above the breakdown threshold power of the background air, the peak of the spectrum of the transmitted pulse is upshifted from the carrier frequency 3.27 GHz of the incident pulse. However, as the power of the incident pulse exceeds the breakdown threshold power of the background air by 30%, a different phenomenon appears. The spectrum of the transmitted pulse begins to have two peaks. One is upshifted and the other one downshifted from the single peak location of the incident pulse. The amount of frequency downshift is comparable to that of the upshifted frequency. A theoretical model describing the experiment of pulse propagation in a self-generated plasma is developed. There are excellent agreements between the experimental results and computer simulations based on this theoretical model, which is also used to further carry out computer experiments identifying the role of plasma introduced wave loss on the result of frequency downshift phenomenon.

Optimum sample size allocation to minimize cost or maximize power for the two-sample trimmed mean test.

PubMed

Guo, Jiin-Huarng; Luh, Wei-Ming

2009-05-01

When planning a study, sample size determination is one of the most important tasks facing the researcher. The size will depend on the purpose of the study, the cost limitations, and the nature of the data. By specifying the standard deviation ratio and/or the sample size ratio, the present study considers the problem of heterogeneous variances and non-normality for Yuen's two-group test and develops sample size formulas to minimize the total cost or maximize the power of the test. For a given power, the sample size allocation ratio can be manipulated so that the proposed formulas can minimize the total cost, the total sample size, or the sum of total sample size and total cost. On the other hand, for a given total cost, the optimum sample size allocation ratio can maximize the statistical power of the test. After the sample size is determined, the present simulation applies Yuen's test to the sample generated, and then the procedure is validated in terms of Type I errors and power. Simulation results show that the proposed formulas can control Type I errors and achieve the desired power under the various conditions specified. Finally, the implications for determining sample sizes in experimental studies and future research are discussed.

Study of a wireless power transmission system for an active capsule endoscope.

PubMed

Xin, Wenhui; Yan, Guozheng; Wang, Wenxin

2010-03-01

An active capsule endoscope (ACE) will consume much more energy than can be power by batteries. Its orientation and position are always undetermined when it continues the natural way down the gastrointestinal track. In order to deliver stable and sufficient energy to ACE safely, a wireless power transmission system based on inductive coupling is presented. The system consists of a Helmholtz primary coil outside and a multiple secondary coils inside the body. The Helmholtz primary coil is driven to generate a uniform alternating magnetic field covering the whole of the alimentary tract, and the multiple secondary coils receive energy regardless of the ACE's position and orientation relative to the generated magnetic field. The human tissue safety of the electromagnetic field generated by transmitting coil was evaluated, based on a high-resolution realistic human model. At least 310 mW usable power can be transmitted under the worst geometrical conditions. Outer dimensions of the power receiver, 10 mm diameter x 12 mm; transmitting power, 25 W; resonant frequency, 400 kHz. The maximum specific absorption rate (SAR) and current density of human tissues are 0.329 W/kg and 3.82 A/m(2), respectively, under the basic restrictions of the International Commission on Non-ionizing Radiation Protection (ICNIRP). The designed wireless power transmission is shown to be feasible and potentially safe in a future application. (c) 2010 John Wiley & Sons, Ltd.

Energy-Efficient Next-Generation Passive Optical Networks Based on Sleep Mode and Heuristic Optimization

NASA Astrophysics Data System (ADS)

Zulai, Luis G. T.; Durand, Fábio R.; Abrão, Taufik

2015-05-01

In this article, an energy-efficiency mechanism for next-generation passive optical networks is investigated through heuristic particle swarm optimization. Ten-gigabit Ethernet-wavelength division multiplexing optical code division multiplexing-passive optical network next-generation passive optical networks are based on the use of a legacy 10-gigabit Ethernet-passive optical network with the advantage of using only an en/decoder pair of optical code division multiplexing technology, thus eliminating the en/decoder at each optical network unit. The proposed joint mechanism is based on the sleep-mode power-saving scheme for a 10-gigabit Ethernet-passive optical network, combined with a power control procedure aiming to adjust the transmitted power of the active optical network units while maximizing the overall energy-efficiency network. The particle swarm optimization based power control algorithm establishes the optimal transmitted power in each optical network unit according to the network pre-defined quality of service requirements. The objective is controlling the power consumption of the optical network unit according to the traffic demand by adjusting its transmitter power in an attempt to maximize the number of transmitted bits with minimum energy consumption, achieving maximal system energy efficiency. Numerical results have revealed that it is possible to save 75% of energy consumption with the proposed particle swarm optimization based sleep-mode energy-efficiency mechanism compared to 55% energy savings when just a sleeping-mode-based mechanism is deployed.

Method and Apparatus for Measuring Surface Air Pressure

NASA Technical Reports Server (NTRS)

Lin, Bing (Inventor); Hu, Yongxiang (Inventor)

2014-01-01

The present invention is directed to an apparatus and method for remotely measuring surface air pressure. In one embodiment, the method of the present invention utilizes the steps of transmitting a signal having multiple frequencies into the atmosphere, measuring the transmitted/reflected signal to determine the relative received power level of each frequency and then determining the surface air pressure based upon the attenuation of the transmitted frequencies.

Perceptually tuned low-bit-rate video codec for ATM networks

NASA Astrophysics Data System (ADS)

Chou, Chun-Hsien

1996-02-01

In order to maintain high visual quality in transmitting low bit-rate video signals over asynchronous transfer mode (ATM) networks, a layered coding scheme that incorporates the human visual system (HVS), motion compensation (MC), and conditional replenishment (CR) is presented in this paper. An empirical perceptual model is proposed to estimate the spatio- temporal just-noticeable distortion (STJND) profile for each frame, by which perceptually important (PI) prediction-error signals can be located. Because of the limited channel capacity of the base layer, only coded data of motion vectors, the PI signals within a small strip of the prediction-error image and, if there are remaining bits, the PI signals outside the strip are transmitted by the cells of the base-layer channel. The rest of the coded data are transmitted by the second-layer cells which may be lost due to channel error or network congestion. Simulation results show that visual quality of the reconstructed CIF sequence is acceptable when the capacity of the base-layer channel is allocated with 2 multiplied by 64 kbps and the cells of the second layer are all lost.

Phased Array Focusing for Acoustic Wireless Power Transfer.

PubMed

Tseng, Victor Farm-Guoo; Bedair, Sarah S; Lazarus, Nathan

2018-01-01

Wireless power transfer (WPT) through acoustic waves can achieve higher efficiencies than inductive coupling when the distance is above several times the transducer size. This paper demonstrates the use of ultrasonic phased arrays to focus power to receivers at arbitrary locations to increase the power transfer efficiency. Using a phased array consisting of 37 elements at a distance nearly 5 times the receiver transducer diameter, a factor of 2.6 increase in efficiency was achieved when compared to a case equivalent to a single large transducer with the same peak efficiency distance. The array has a total diameter of 7 cm, and transmits through air at 40 kHz to a 1.1-cm diameter receiver, achieving a peak overall efficiency of 4% at a distance of 5 cm. By adjusting the focal distance, the efficiency can also be maintained relatively constant at distances up to 9 cm. Numerical models were developed and shown to closely match the experimental energy transfer behavior; modeling results indicate that the efficiency can be further doubled by increasing the number of elements. For comparison, an inductive WPT system was also built with the diameters of the transmitting and receiving coils equivalent to the dimensions of the transmitting ultrasonic phased array and receiver transducer, and the acoustic WPT system achieved higher efficiencies than the inductive WPT system when the transmit-to-receive distance is above 5 cm. In addition, beam angle steering was demonstrated by using a simplified seven-element 1-D array, achieving power transfer less dependent on receiver placement.

Solar power satellite system definition study. Volume 3: Laser SPS analysis, phase 3

NASA Technical Reports Server (NTRS)

1980-01-01

The potential use of lasers for transmitting power to Earth from Solar Power Satellites was examined. Free electron lasers appear most promising and would have some benefits over microwave power transmission. Further research in laser technology is needed.

Cross-Layer Resource Allocation for Wireless Visual Sensor Networks and Mobile Ad Hoc Networks

DTIC Science & Technology

2014-10-01

MMD), minimizes the maximum dis- tortion among all nodes of the network, promoting a rather unbiased treatment of the nodes. We employed the Particle...achieve the ideal tradeoff between the transmitted video quality and energy consumption. Each sensor node has a bit rate that can be used for both...Distortion (MMD), minimizes the maximum distortion among all nodes of the network, promoting a rather unbiased treatment of the nodes. For both criteria

A Study on Cost Allocation in Nuclear Power Coupled with Desalination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, ManKi; Kim, SeungSu; Moon, KeeHwan

As for a single-purpose desalination plant, there is no particular difficulty in computing the unit cost of the water, which is obtained by dividing the annual total costs by the output of fresh water. When it comes to a dual-purpose plant, cost allocation is needed between the two products. No cost allocation is needed in some cases where two alternatives producing the same water and electricity output are to be compared. In these cases, the consideration of the total cost is then sufficient. This study assumes MED (Multi-Effect Distillation) technology is adopted when nuclear power is coupled with desalination. Themore » total production cost of the two commodities in dual-purpose plant can easily be obtained by using costing methods, if the necessary raw data are available. However, it is not easy to calculate a separate cost for each product, because high-pressure steam plant costs cannot be allocated to one or the other without adopting arbitrary methods. Investigation on power credit method is carried out focusing on the cost allocation of combined benefits due to dual production, electricity and water. The illustrative calculation is taken from Preliminary Economic Feasibility Study of Nuclear Desalination in Madura Island, Indonesia. The study is being performed by BATAN (National Nuclear Energy Agency), KAERI (Korean Atomic Energy Research Institute) and under support of the IAEA (International Atomic Energy Agency) started in the year 2002 in order to perform a preliminary economic feasibility in providing the Madurese with sufficient power and potable water for the public and to support industrialization and tourism in Madura Region. The SMART reactor coupled with MED is considered to be an option to produce electricity and potable water. This study indicates that the correct recognition of combined benefits attributable to dual production is important in carrying out economics of desalination coupled with nuclear power. (authors)« less

Innovative Approach for Developing Spacecraft Interior Acoustic Requirement Allocation

NASA Technical Reports Server (NTRS)

Chu, S. Reynold; Dandaroy, Indranil; Allen, Christopher S.

2016-01-01

The Orion Multi-Purpose Crew Vehicle (MPCV) is an American spacecraft for carrying four astronauts during deep space missions. This paper describes an innovative application of Power Injection Method (PIM) for allocating Orion cabin continuous noise Sound Pressure Level (SPL) limits to the sound power level (PWL) limits of major noise sources in the Environmental Control and Life Support System (ECLSS) during all mission phases. PIM is simulated using both Statistical Energy Analysis (SEA) and Hybrid Statistical Energy Analysis-Finite Element (SEA-FE) models of the Orion MPCV to obtain the transfer matrix from the PWL of the noise sources to the acoustic energies of the receivers, i.e., the cavities associated with the cabin habitable volume. The goal of the allocation strategy is to control the total energy of cabin habitable volume for maintaining the required SPL limits. Simulations are used to demonstrate that applying the allocated PWLs to the noise sources in the models indeed reproduces the SPL limits in the habitable volume. The effects of Noise Control Treatment (NCT) on allocated noise source PWLs are investigated. The measurement of source PWLs of involved fan and pump development units are also discussed as it is related to some case-specific details of the allocation strategy discussed here.

Surface plasmons in new waveguide structures containing ultra-thin metal and silicon layers

NASA Astrophysics Data System (ADS)

Shabat, M. M.; Ubeid, M. F.; Abu Rahma, M. A.

2018-05-01

Reflected and transmitted powers due to the interaction of electromagnetic waves with a structure containing thin metal and silicon layer are investigated in more detail. The formulations for the transverse electric wave case are provided. Transfer matrix method is used to find the reflection and the transmission coefficients at each interface. Numerical results are presented to show the effect of the structure parameters, the incidence angle and the wavelength on the reflected, transmitted and loss powers.

Linearizing an intermodulation radar transmitter by filtering switched tones

NASA Astrophysics Data System (ADS)

Mazzaro, Gregory J.; Sherbondy, Andrew J.; Ranney, Kenneth I.; Sherbondy, Kelly D.; Martone, Anthony F.

2017-05-01

For nonlinear radar, the transmit power required to measure a detectable response from a target is relatively high, and generating that high power is achieved at the cost of linearity. This paper applies the distortion mitigation technique Linearization by Time-Multiplexed Spectrum (LITMUS) to intermodulation radar, a type of nonlinear radar which receives spectral content produced by the mixing of multiple frequencies at a nonlinear target. By implementing LITMUS, an experimental detection system for an intermodulation radar achieves a signal-to-noise ratio up to 20 dB for a total transmit power of approximately 80 mW and nonlinear targets placed at a standoff distance of 2 meters.

Optimized ECR plasma apparatus with varied microwave window thickness

DOEpatents

Berry, Lee A.

1995-01-01

The present invention describes a technique to control the radial profile of microwave power in an ECR plasma discharge. In order to provide for a uniform plasma density to a specimen, uniform energy absorption by the plasma is desired. By controlling the radial profile of the microwave power transmitted through the microwave window of a reactor, the profile of the transmitted energy to the plasma can be controlled in order to have uniform energy absorption by the plasma. An advantage of controlling the profile using the window transmission characteristics is that variations to the radial profile of microwave power can be made without changing the microwave coupler or reactor design.

Report on Transmission Cost Allocation for RTOs and Others (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coles, L.

2011-06-01

Presented at the MARC 2011 Annual Conference, 6 June 2011, Rapid City, South Dakota. This presentation provides an overview of the latest research findings and policy developments pertaining to cost allocation and new variable generation resources on the power grid.

47 CFR 95.855 - Transmitter effective radiated power limitation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transmitter effective radiated power limitation. The effective radiated power (ERP) of each CTS and RTU shall... with an ERP exceeding 20 watts. No mobile RTU may transmit with an ERP exceeding 4 watts. [64 FR 59663...

47 CFR 95.855 - Transmitter effective radiated power limitation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transmitter effective radiated power limitation. The effective radiated power (ERP) of each CTS and RTU shall... with an ERP exceeding 20 watts. No mobile RTU may transmit with an ERP exceeding 4 watts. [64 FR 59663...

Vibration Power Flow In A Constrained Layer Damping Cylindrical Shell

NASA Astrophysics Data System (ADS)

Wang, Yun; Zheng, Gangtie

2012-07-01

In this paper, the vibration power flow in a constrained layer damping (CLD) cylindrical shell using wave propagation approach is investigated. The dynamic equations of the shell are derived with the Hamilton principle in conjunction with the Donnell shell assumption. With these equations, the dynamic responses of the system under a line circumferential cosine harmonic exciting force is obtained by employing the Fourier transform and the residue theorem. The vibration power flows inputted to the system and transmitted along the shell axial direction are both studied. The results show that input power flow varies with driving frequency and circumferential mode order, and the constrained damping layer can obviously restrict the exciting force from inputting power flow into the base shell especially for a thicker viscoelastic layer, a thicker or stiffer constraining layer (CL), and a higher circumferential mode order, can rapidly attenuate the vibration power flow transmitted along the base shell axial direction.

Choice of antenna geometry for microwave power transmission from solar power satellites

NASA Technical Reports Server (NTRS)

Potter, Seth D.

1992-01-01

A comparison is made between square and circular transmitting antennas for solar power satellite microwave power transmission. It is seen that the exclusion zone around the rectenna needed to protect populations from microwaves is smaller for a circular antenna operating at 2.45 GHz than it is for a square antenna at that frequency. If the frequency is increased, the exclusion zone size remains the same for a square antenna, but becomes even smaller for a circular antenna. Peak beam intensity is the same for both antennas if the frequency and antenna area are equal. The circular antenna puts a somewhat greater amount of power in the main lobe and somewhat less in the side lobes. Since rain attenuation and atmospheric heating remain problems above 10 GHz, it is recommended that future solar power satellite work concentrate on circular transmitting antennas at frequencies of roughly 10 GHz.

47 CFR 74.682 - Station identification.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Station identification. 74.682 Section 74.682... Stations § 74.682 Station identification. (a) Each television broadcast auxiliary station operating with a transmitter output power of 1 watt or more must, when actually transmitting programs, transmit station...

Communication on SWIPT and EH Using Electromagnetic Behaviour for Power Allocation in Wireless Networks

NASA Astrophysics Data System (ADS)

Khan, Sohel Rana; Ajij, Sayyad

2017-12-01

This review paper focuses on the basic relations between wireless power transfer, wireless information transfer and combined phenomenon of simultaneous wireless information and power transfer. The authors reviewed and discussed electromagnetic fields behaviour (EMB) for enhancing the power allocation strategies (PAS) in energy harvesting (EH) wireless communication systems. Further, this paper presents relations between Friis transmission equation and Maxwell's equations to be used in propagation models for reduction in specific absorption rate (SAR). This paper provides a review of various methods and concepts reported in earlier works. This paper also reviews Poynting vector and power densities along with boundary conditions for antennas and human body. Finally, this paper explores the usage of electromagnetic behaviour for the possible enhancement in power saving methods for electromagnetic behaviour centered-wireless energy harvesting (EMBC-WEH). At the same time, possibilities of PAS for reduction in SAR are discussed.

Single frequency RF powered ECG telemetry system

NASA Technical Reports Server (NTRS)

Ko, W. H.; Hynecek, J.; Homa, J.

1979-01-01

It has been demonstrated that a radio frequency magnetic field can be used to power implanted electronic circuitry for short range telemetry to replace batteries. A substantial reduction in implanted volume can be achieved by using only one RF tank circuit for receiving the RF power and transmitting the telemetered information. A single channel telemetry system of this type, using time sharing techniques, was developed and employed to transmit the ECG signal from Rhesus monkeys in primate chairs. The signal from the implant is received during the period when the RF powering radiation is interrupted. The ECG signal is carried by 20-microsec pulse position modulated pulses, referred to the trailing edge of the RF powering pulse. Satisfactory results have been obtained with this single frequency system. The concept and the design presented may be useful for short-range long-term implant telemetry systems.

Control Law-Control Allocation Interaction: F/A-18 PA Simulation Test - Bed

NASA Technical Reports Server (NTRS)

Durham, Wayne; Nelson, Mark

2001-01-01

This report documents the first stage of research into Control Law - Control Allocation Interactions. A three-year research effort was originally proposed: 1. Create a desktop flight simulation environment under which experiments related to the open questions may be conducted. 2. Conduct research to determine which aspects of control allocation have impact upon control law design that merits further research. 3. Conduct research into those aspects of control allocation identified above, and their impacts upon control law design. Simulation code was written utilizing the F/A-18 airframe in the power approach (PA) configuration. A dynamic inversion control law was implemented and used to drive a state-of-the-art control allocation subroutine.

Two-phase designs for joint quantitative-trait-dependent and genotype-dependent sampling in post-GWAS regional sequencing.

PubMed

Espin-Garcia, Osvaldo; Craiu, Radu V; Bull, Shelley B

2018-02-01

We evaluate two-phase designs to follow-up findings from genome-wide association study (GWAS) when the cost of regional sequencing in the entire cohort is prohibitive. We develop novel expectation-maximization-based inference under a semiparametric maximum likelihood formulation tailored for post-GWAS inference. A GWAS-SNP (where SNP is single nucleotide polymorphism) serves as a surrogate covariate in inferring association between a sequence variant and a normally distributed quantitative trait (QT). We assess test validity and quantify efficiency and power of joint QT-SNP-dependent sampling and analysis under alternative sample allocations by simulations. Joint allocation balanced on SNP genotype and extreme-QT strata yields significant power improvements compared to marginal QT- or SNP-based allocations. We illustrate the proposed method and evaluate the sensitivity of sample allocation to sampling variation using data from a sequencing study of systolic blood pressure. © 2017 The Authors. Genetic Epidemiology Published by Wiley Periodicals, Inc.

Solar power satellite system definition study, volume 7

NASA Technical Reports Server (NTRS)

1977-01-01

Guidelines and assumptions used in the design of a system of geosynchronous satellites for transmitting solar power to earth were discussed as well as the design evolutions of the principle types of solar power satellites and space support systems.

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... power control level. Power must be summed across all antennas and antenna elements. The average must not... symbols, during which the average symbol envelope power is constant. (q) RLAN. Radio Local Area Network. (r) Transmit Power Control (TPC). A feature that enables a U-NII device to dynamically switch between...

Fluid Power Technician

ERIC Educational Resources Information Center

Moore, Pam

2008-01-01

Fluid power technicians, sometimes called hydraulic and pneumatic technicians, work with equipment that utilizes the pressure of a liquid or gas in a closed container to transmit, multiply, or control power. Working under the supervision of an engineer or engineering staff, they assemble, install, maintain, and test fluid power equipment.…

10 CFR 205.308 - Filing schedule and annual reports.

Code of Federal Regulations, 2010 CFR

2010-01-01

....308 Energy DEPARTMENT OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System... to Transmit Electric Energy to A Foreign Country § 205.308 Filing schedule and annual reports. (a) Persons authorized to transmit electric energy from the United States shall promptly file all supplements...

10 CFR 205.308 - Filing schedule and annual reports.

Code of Federal Regulations, 2011 CFR

2011-01-01

....308 Energy DEPARTMENT OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System... to Transmit Electric Energy to A Foreign Country § 205.308 Filing schedule and annual reports. (a) Persons authorized to transmit electric energy from the United States shall promptly file all supplements...

77 FR 11515 - Application To Export Electric Energy; Pilot Power Group, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-27

... reliability of the U.S. electric power supply system. Copies of this application will be made available, upon... DEPARTMENT OF ENERGY [OE Docket No. EA-383] Application To Export Electric Energy; Pilot Power... application. SUMMARY: Pilot Power Group, Inc. (Pilot Power) has applied for authority to transmit electric...

Energy Efficiency Maximization of Practical Wireless Communication Systems

NASA Astrophysics Data System (ADS)

Eraslan, Eren

Energy consumption of the modern wireless communication systems is rapidly growing due to the ever-increasing data demand and the advanced solutions employed in order to address this demand, such as multiple-input multiple-output (MIMO) and orthogonal frequency division multiplexing (OFDM) techniques. These MIMO systems are power hungry, however, they are capable of changing the transmission parameters, such as number of spatial streams, number of transmitter/receiver antennas, modulation, code rate, and transmit power. They can thus choose the best mode out of possibly thousands of modes in order to optimize an objective function. This problem is referred to as the link adaptation problem. In this work, we focus on the link adaptation for energy efficiency maximization problem, which is defined as choosing the optimal transmission mode to maximize the number of successfully transmitted bits per unit energy consumed by the link. We model the energy consumption and throughput performances of a MIMO-OFDM link and develop a practical link adaptation protocol, which senses the channel conditions and changes its transmission mode in real-time. It turns out that the brute force search, which is usually assumed in previous works, is prohibitively complex, especially when there are large numbers of transmit power levels to choose from. We analyze the relationship between the energy efficiency and transmit power, and prove that energy efficiency of a link is a single-peaked quasiconcave function of transmit power. This leads us to develop a low-complexity algorithm that finds a near-optimal transmit power and take this dimension out of the search space. We further prune the search space by analyzing the singular value decomposition of the channel and excluding the modes that use higher number of spatial streams than the channel can support. These algorithms and our novel formulations provide simpler computations and limit the search space into a much smaller set; hence reducing the computational complexity by orders of magnitude without sacrificing the performance. The result of this work is a highly practical link adaptation protocol for maximizing the energy efficiency of modern wireless communication systems. Simulation results show orders of magnitude gain in the energy efficiency of the link. We also implemented the link adaptation protocol on real-time MIMO-OFDM radios and we report on the experimental results. To the best of our knowledge, this is the first reported testbed that is capable of performing energy-efficient fast link adaptation using PHY layer information.

Joint Interference Alignment and Power Allocation for K-User Multicell MIMO Channel through Staggered Antenna Switching.

PubMed

Selvaprabhu, Poongundran; Chinnadurai, Sunil; Sarker, Md Abdul Latif; Lee, Moon Ho

2018-01-28

In this paper, we characterise the joint interference alignment (IA) and power allocation strategies for a K -user multicell multiple-input multiple-output (MIMO) Gaussian interference channel. We consider a MIMO interference channel with blind-IA through staggered antenna switching on the receiver. We explore the power allocation and feasibility condition for cooperative cell-edge (CE) mobile users (MUs) by assuming that the channel state information is unknown. The new insight behind the transmission strategy of the proposed scheme is premeditated (randomly generated transmission strategy) and partial cooperative CE MUs, where the transmitter is equipped with a conventional antenna, the receiver is equipped with a reconfigurable multimode antenna (staggered antenna switching pattern), and the receiver switches between preset T modes. Our proposed scheme assists and aligns the desired signals and interference signals to cancel the common interference signals because the received signal must have a corresponding independent signal subspace. The capacity for a K -user multicell MIMO Gaussian interference channel with reconfigurable multimode antennas is completely characterised. Furthermore, we show that the proposed K -user multicell MIMO scheduling and K -user L -cell CEUs partial cooperation algorithms elaborate the generalisation of K -user IA and power allocation strategies. The numerical results demonstrate that the proposed intercell interference scheme with partial-cooperative CE MUs achieves better capacity and signal-to-interference plus noise ratio (SINR) performance compared to noncooperative CE MUs and without intercell interference schemes.

Joint Interference Alignment and Power Allocation for K-User Multicell MIMO Channel through Staggered Antenna Switching

PubMed Central

2018-01-01

In this paper, we characterise the joint interference alignment (IA) and power allocation strategies for a K-user multicell multiple-input multiple-output (MIMO) Gaussian interference channel. We consider a MIMO interference channel with blind-IA through staggered antenna switching on the receiver. We explore the power allocation and feasibility condition for cooperative cell-edge (CE) mobile users (MUs) by assuming that the channel state information is unknown. The new insight behind the transmission strategy of the proposed scheme is premeditated (randomly generated transmission strategy) and partial cooperative CE MUs, where the transmitter is equipped with a conventional antenna, the receiver is equipped with a reconfigurable multimode antenna (staggered antenna switching pattern), and the receiver switches between preset T modes. Our proposed scheme assists and aligns the desired signals and interference signals to cancel the common interference signals because the received signal must have a corresponding independent signal subspace. The capacity for a K-user multicell MIMO Gaussian interference channel with reconfigurable multimode antennas is completely characterised. Furthermore, we show that the proposed K-user multicell MIMO scheduling and K-user L-cell CEUs partial cooperation algorithms elaborate the generalisation of K-user IA and power allocation strategies. The numerical results demonstrate that the proposed intercell interference scheme with partial-cooperative CE MUs achieves better capacity and signal-to-interference plus noise ratio (SINR) performance compared to noncooperative CE MUs and without intercell interference schemes. PMID:29382100

Traffic-Aware Channel Allocation and Routing in Multichannel, Multi-Radio Wireless Networks

DTIC Science & Technology

2012-01-01

come up with interesting ideas that eventually led me to my Ph.D. research topic that is presented in the Chapter 5 of this disserta- tion. Next, I...exam process. Their comments and suggestions helped me im- prove my research topic and project it in a perspective suitable for a wider audience. I...backo , and xed rate header transmissions. These overheads become prominent in short packets that are transmitted at high data rates. We address this

A system for tranmitting low frequency analog signals over ac power lines

DOEpatents

Baker, S.P.; Durall, R.L.; Haynes, H.D.

1987-07-30

A system for transmitting low frequency analog signals over ac power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an ac power line. The modulation signal frequency range is selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the ac power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal. 4 figs.

Air quality and climate benefits of long-distance electricity transmission in China

NASA Astrophysics Data System (ADS)

Peng, Wei; Yuan, Jiahai; Zhao, Yu; Lin, Meiyun; Zhang, Qiang; Victor, David G.; Mauzerall, Denise L.

2017-06-01

China is the world’s top carbon emitter and suffers from severe air pollution. It has recently made commitments to improve air quality and to peak its CO2 emissions by 2030. We examine one strategy that can potentially address both issues—utilizing long-distance electricity transmission to bring renewable power to the polluted eastern provinces. Based on an integrated assessment using state-of-the-science atmospheric modeling and recent epidemiological evidence, we find that transmitting a hybrid of renewable (60%) and coal power (40%) (Hybrid-by-wire) reduces 16% more national air-pollution-associated deaths and decreases three times more carbon emissions than transmitting only coal-based electricity. Moreover, although we find that transmitting coal power (Coal-by-Wire, CbW) is slightly more effective at reducing air pollution impacts than replacing old coal power plants with newer cleaner ones in the east (Coal-by-Rail, CbR) (CbW achieves a 6% greater reduction in national total air-pollution-related mortalities than CbR), both coal scenarios have approximately the same carbon emissions. We thus demonstrate that coordinating transmission planning with renewable energy deployment is critical to maximize both local air quality benefits and global climate benefits.

Progress in Acoustic Transmission of Power through Walls

NASA Technical Reports Server (NTRS)

Sherrit,Stewart; Coty, Benjamin; Bao, Xiaoqi; Bar-Cohen, Yoseph; Badescu, Mircea; Chang, Zensheu

2008-01-01

A document presents updated information on implementation of the wireless acoustic-electric feed-through (WAEF) concept, which was reported in Using Piezoelectric Devices To Transmit Power Through Walls (NPO-41157), NASA Tech Briefs, Vol. 32, No. 6 (June 2008), page 70. To recapitulate: In a basic WAEF setup, a transmitting piezoelectric transducer on one side of a wall is driven at resonance to excite ultrasonic vibrations in the wall. A receiving piezoelectric transducer on the opposite side of the wall converts the vibrations back to an ultrasonic AC electric signal, which is then detected and otherwise processed in a manner that depends on the modulation (if any) applied to the signal and whether the signal is used to transmit power, data, or both. The present document expands upon the previous information concerning underlying physical principles, advantages, and potential applications of WAEF. It discusses the design and construction of breadboard prototype piezoelectric transducers for WAEF. It goes on to present results of computational simulations of performance and results of laboratory tests of the prototypes. In one notable test, a 100-W light bulb was lit by WAEF to demonstrate the feasibility of powering a realistic load.

Compact, high power, energy efficient transmit systems for UUVs using single crystal transducers

NASA Astrophysics Data System (ADS)

Robinson, Harold

2004-05-01

UUVs are currently being designed to perform a multiplitude of tasks in ocean exploration and Naval warfighting. Many of these tasks require the use of active acoustic projectors, and many may require the UUV to operate independently for hours, days, or even weeks. In order for a UUV to be as versatile as possible, its active transmit system must be versatile as well, implying that broad acoustic bandwidths are a must. However, due to size and battery life limitations, this broadband system must also be compact and energy efficient. By virtue of their extraordinary material properties, ferroelectric single crystals are the ideal transduction material for developing such broadband systems. The effect of their high coupling factor on transmit systems shall be illustrated by showing the dramatic impact on amplifier size, power factor, and acoustic response that is possible using these materials. In particular, a transducer built with these materials can be well matched to the power amplifier, i.e., 80% or more of the amplifier power reaches the transducer, over decades of frequency. Measured results from several prototype single crystal transducers shall be presented to demonstrate that the theoretical gains are actually realizable in practical devices. [Work sponsored by DARPA.

Analysis of SAR distribution in human head of antenna used in wireless power transform based on magnetic resonance.

PubMed

Gong, Feixiang; Wei, Zhiqiang; Cong, Yanping; Chi, Haokun; Yin, Bo; Sun, Mingui

2017-07-20

In this paper, a novel wireless power transfer antenna system was designed for human head implantable devices. The antenna system used the structure of three plates and four coils and operated at low frequencies to transfer power via near field. In order to verify the electromagnetic radiation safety on the human head, the electromagnetic intensity and specific absorption rate (SAR) were studied by finite-difference-time-domain (FDTD) method. A three-layer model of human head including skin, bone and brain tissues was constructed. The transmitting and receiving antenna were set outside and inside the model. The local and average SAR were simulated at the resonance frequency of 18.67 MHz in two situations, in one scenario both transmitting and receiving coil worked, while in the other scenario only the transmitting coil worked. The results showed that the maximum of 10 g SAR average value of human thoracic were 0.142 W/kg and 0.148 W/kg, respectively, both were lower than the international safety standards for human body of the ICNIRP and FCC, which verified the safety of the human body in wireless power transmission based on magnetic coupling resonance.

76 FR 20651 - Application To Export Electric Energy; Cargill Power Markets, LLC

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

.... electric power supply system. Copies of this application will be made available, upon request, for public... DEPARTMENT OF ENERGY [OE Docket No. EA-378] Application To Export Electric Energy; Cargill Power... application. SUMMARY: Cargill Power Markets, LLC (CPM) has applied for authority to transmit electric energy...

Wireless visual sensor network resource allocation using cross-layer optimization

NASA Astrophysics Data System (ADS)

Bentley, Elizabeth S.; Matyjas, John D.; Medley, Michael J.; Kondi, Lisimachos P.

2009-01-01

In this paper, we propose an approach to manage network resources for a Direct Sequence Code Division Multiple Access (DS-CDMA) visual sensor network where nodes monitor scenes with varying levels of motion. It uses cross-layer optimization across the physical layer, the link layer and the application layer. Our technique simultaneously assigns a source coding rate, a channel coding rate, and a power level to all nodes in the network based on one of two criteria that maximize the quality of video of the entire network as a whole, subject to a constraint on the total chip rate. One criterion results in the minimal average end-to-end distortion amongst all nodes, while the other criterion minimizes the maximum distortion of the network. Our approach allows one to determine the capacity of the visual sensor network based on the number of nodes and the quality of video that must be transmitted. For bandwidth-limited applications, one can also determine the minimum bandwidth needed to accommodate a number of nodes with a specific target chip rate. Video captured by a sensor node camera is encoded and decoded using the H.264 video codec by a centralized control unit at the network layer. To reduce the computational complexity of the solution, Universal Rate-Distortion Characteristics (URDCs) are obtained experimentally to relate bit error probabilities to the distortion of corrupted video. Bit error rates are found first by using Viterbi's upper bounds on the bit error probability and second, by simulating nodes transmitting data spread by Total Square Correlation (TSC) codes over a Rayleigh-faded DS-CDMA channel and receiving that data using Auxiliary Vector (AV) filtering.

ECR apparatus with magnetic coil for plasma refractive index control

DOEpatents

Berry, L.A.

1994-04-26

The present invention describes a technique to control the radial profile of microwave power in an ECR plasma discharge. In order to provide for a uniform plasma density to a specimen, uniform energy absorption by the plasma is desired. By controlling the radial profile of the microwave power transmitted through the microwave window of a reactor, the profile of the transmitted energy to the plasma can be controlled in order to have uniform energy absorption by the plasma. An advantage of controlling the profile using the window transmission characteristics is that variations to the radial profile of microwave power can be made without changing the microwave coupler or reactor design. 9 figures.

ECR apparatus with magnetic coil for plasma refractive index control

DOEpatents

Berry, Lee A.

1994-01-01

The present invention describes a technique to control the radial profile of microwave power in an ECR plasma discharge. In order to provide for a uniform plasma density to a specimen, uniform energy absorption by the plasma is desired. By controlling the radial profile of the microwave power transmitted through the microwave window of a reactor, the profile of the transmitted energy to the plasma can be controlled in order to have uniform energy absorption by the plasma. An advantage of controlling the profile using the window transmission characteristics is that variations to the radial profile of microwave power can be made without changing the microwave coupler or reactor design.

Optimized ECR plasma apparatus with varied microwave window thickness

DOEpatents

Berry, L.A.

1995-11-14

The present invention describes a technique to control the radial profile of microwave power in an ECR plasma discharge. In order to provide for a uniform plasma density to a specimen, uniform energy absorption by the plasma is desired. By controlling the radial profile of the microwave power transmitted through the microwave window of a reactor, the profile of the transmitted energy to the plasma can be controlled in order to have uniform energy absorption by the plasma. An advantage of controlling the profile using the window transmission characteristics is that variations to the radial profile of microwave power can be made without changing the microwave coupler or reactor design. 9 figs.

Power corrupts co-operation: cognitive and motivational effects in a double EEG paradigm.

PubMed

Kanso, Riam; Hewstone, Miles; Hawkins, Erin; Waszczuk, Monika; Nobre, Anna Christina

2014-02-01

This study investigated the effect of interpersonal power on co-operative performance. We used a paired electro-encephalogram paradigm: pairs of participants performed an attention task, followed by feedback indicating monetary loss or gain on every trial. Participants were randomly allocated to the power-holder, subordinate or neutral group by creating different levels of control over how a joint monetary reward would be allocated. We found that power was associated with reduced behavioural accuracy. Event-related potential analysis showed that power-holders devoted less motivational resources to their targets than did subordinates or neutrals, but did not differ at the level of early conflict detection. Their feedback potential results showed a greater expectation of rewards but reduced subjective magnitude attributed to losses. Subordinates, on the other hand, were asymmetrically sensitive to power-holders' targets. They expected fewer rewards, but attributed greater significance to losses. Our study shows that power corrupts balanced co-operation with subordinates.

Power corrupts co-operation: cognitive and motivational effects in a double EEG paradigm

PubMed Central

Kanso, Riam; Hewstone, Miles; Hawkins, Erin; Waszczuk, Monika; Nobre, Anna Christina

2014-01-01

This study investigated the effect of interpersonal power on co-operative performance. We used a paired electro-encephalogram paradigm: pairs of participants performed an attention task, followed by feedback indicating monetary loss or gain on every trial. Participants were randomly allocated to the power-holder, subordinate or neutral group by creating different levels of control over how a joint monetary reward would be allocated. We found that power was associated with reduced behavioural accuracy. Event-related potential analysis showed that power-holders devoted less motivational resources to their targets than did subordinates or neutrals, but did not differ at the level of early conflict detection. Their feedback potential results showed a greater expectation of rewards but reduced subjective magnitude attributed to losses. Subordinates, on the other hand, were asymmetrically sensitive to power-holders’ targets. They expected fewer rewards, but attributed greater significance to losses. Our study shows that power corrupts balanced co-operation with subordinates. PMID:23160813

Power plant allocation in East Kalimantan considering total cost and emissions

NASA Astrophysics Data System (ADS)

Muslimin; Utomo, D. S.

2018-04-01

The fulfillment of electricity need in East Kalimantan is the responsibility of State Electricity Company/Perusahaan Listrik Negara (PLN). But PLN faces constraints in the lack of generating capacity it has. So the allocation of power loads in East Kalimantan has its own challenges. Additional power supplies from other parties are required. In this study, there are four scenarios tested to meet the electricity needs in East Kalimantan with the goal of minimizing costs and emissions. The first scenario is only by using PLN power plant. The second scenario is by combining PLN + Independent Power Producer (IPP) power plants. The third scenario is by using PLN + Rented power plants. The fourth scenario is by using PLN + Excess capacity generation. Numerical experiment using nonlinear programming is conducted with the help of the solver. The result shows that in the peak load condition, the best combination is scenario 2 (PLN + IPP). While at the lowest load condition, the cheapest scenario is PLN + IPP while the lowest emission is PLN + Rent.

Sexual relationship power as a mediator between dating violence and sexually transmitted infections among college women.

PubMed

Buelna, Christina; Ulloa, Emilio C; Ulibarri, Monica D

2009-08-01

This study examined relationship power as a possible mediator of the relationship between dating violence and sexually transmitted infections (STIs). The proposed mediation model was based on the theory of gender and power as well as previous research on intimate partner violence and STI risk. Survey results from a sample of 290 single, undergraduate women indicated that 85% experienced at least one form of dating violence victimization in the past year, 5.9% tested positive for an STI, and 5.2% received treatment for an STI. Results revealed that women with lower levels of sexual relationship power had higher rates of dating violence victimization and STIs; also, sexual relationship power partially mediated the relationship between dating violence victimization and STIs. Future dating violence and STI-prevention interventions targeting young women may want to use an empowerment approach to decrease their likelihood of dating violence victimization and STI risk.

Parametric analysis of hollow conductor parallel and coaxial transmission lines for high frequency space power distribution

NASA Technical Reports Server (NTRS)

Jeffries, K. S.; Renz, D. D.

1984-01-01

A parametric analysis was performed of transmission cables for transmitting electrical power at high voltage (up to 1000 V) and high frequency (10 to 30 kHz) for high power (100 kW or more) space missions. Large diameter (5 to 30 mm) hollow conductors were considered in closely spaced coaxial configurations and in parallel lines. Formulas were derived to calculate inductance and resistance for these conductors. Curves of cable conductance, mass, inductance, capacitance, resistance, power loss, and temperature were plotted for various conductor diameters, conductor thickness, and alternating current frequencies. An example 5 mm diameter coaxial cable with 0.5 mm conductor thickness was calculated to transmit 100 kW at 1000 Vac, 50 m with a power loss of 1900 W, an inductance of 1.45 micron and a capacitance of 0.07 micron-F. The computer programs written for this analysis are listed in the appendix.

Profitability primer: a guide to profitability analysis in the electric power industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woo, C.K.; Lloyd-Zannetti, D.; Martin, J.

1996-06-01

As the electric power industry is opened to forces of competition, increased attention must be focused to develop products and services that deliver good value to customers and to identify customer segments that are profitable to serve. This primer introduces the concept of profitability analysis and its application to the electric power industry. The primer recognizes that some segments of the business will remain monopolistic and subject to regulations, while other segments will become competitive. The primer also recognizes that customer profitability is critically dependent on a host of related issues such as how internal costs are allocated to variousmore » functions and how revenues are collected and allocated.« less

77 FR 65681 - Boulder Canyon Project-Post-2017 Resource Pool

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-30

... marketing criteria must submit written comments to Western's Desert Southwest Customer Service Regional... defined as ``Schedule D'' to be allocated to new allottees. In accordance with the HPAA, Western allocated... allottee may purchase power only upon the execution of an electric service contract and satisfaction of all...

Status Valued Goal Objects and Performance Expectations

ERIC Educational Resources Information Center

Hysom, Stuart J.

2009-01-01

I designed an experiment to test predictions, derived from expectation states theories, that the unequal allocation of social rewards among collective task-focused actors will affect the actors' rates of power and prestige behavior. Past research shows that allocations of exchangeable resources can have these effects. The prediction, however, is…

Energy-efficient downlink resource management in self-organized OFDMA-based two-tier femtocell networks

NASA Astrophysics Data System (ADS)

Shahid, Adnan; Aslam, Saleem; Kim, Hyung Seok; Lee, Kyung-Geun

2015-12-01

Femtocell is a novel technology that is used for escalating indoor coverage as well as the capacity of traditional cellular networks. However, interference is the limiting factor for performance improvement due to co-channel deployment between macrocells and femtocells. The traditional network planning is not feasible because of the random deployment of femtocells. Therefore, self-organization approaches are the key to having successful deployment of femtocells. This study presents the joint resource block (RB) and power allocation task for the two-tier femtocell network in a self-organizing manner, with the concern to minimizing the impact of interference and maximizing the energy efficiency. In this study, we analyze the performance of the system in terms of the energy efficiency, which is composed of both the transmission and circuit power. Most of the previous studies investigate the performance regarding the throughput requirement of the two-tier femtocell network while the energy efficiency aspect is largely ignored. Here, the joint allocation task is modeled as a non-cooperative game which is demonstrated to exhibit pure and unique Nash equilibrium. In order to reduce the complexity of the proposed non-cooperative game, the joint RB and power allocation task is divided into two subproblems: an RB allocation and a particle swarm optimization-based power allocation. The analysis of the proposed game is carried out in terms of not only energy efficiency but also throughput. With practical 3rd Generation Partnership Project (3GPP) Long-Term Evolution (LTE) parameters, the simulation results illustrate the superior performance of the proposed game as compared to the traditional methods. Also, the comparison is carried out with the joint allocation scheme which only considers the throughput as the objective function. The results illustrate that significant performance improvement is achieved in terms of energy efficiency with slight loss in the throughput. The analysis in regard to energy efficiency and throughput of the two-tier femtocell network is carried out in terms of the performance metrics, which include convergence, impact of varying RBs, impact of femtocell density, and the fairness index.

Wireless Medical Devices for MRI-Guided Interventions

NASA Astrophysics Data System (ADS)

Venkateswaran, Madhav

Wireless techniques can play an important role in next-generation, image-guided surgical techniques with integration strategies being the key. We present our investigations on three wireless applications. First, we validate a position and orientation independent method to noninvasively monitor wireless power delivery using current perturbation measurements of switched load modulation of the RF carrier. This is important for safe and efficient powering without using bulky batteries or invasive cables. Use of MRI transmit RF pulses for simultaneous powering is investigated in the second part. We develop system models for the MRI transmit chain, wireless powering circuits and a typical load. Detailed analysis and validation of nonlinear and cascaded modeling strategies are performed, useful for decoupled optimization of the harvester coil and RF-DC converter. MRI pulse sequences are investigated for suitability for simultaneous powering. Simulations indicate that a 1.8V, 2 mA load can be powered with a 100% duty cycle using a 30° fGRE sequence, despite the RF duty cycle being 44 mW for a 30° flip angle, consistent with model predictions. Investigations on imaging artifacts indicates that distortion is mostly restricted to within the physical span of the harvester coil in the imaging volume, with the homogeneous B1+ transmit field providing positioning flexibility to minimize this for simultaneous powering. The models are potentially valuable in designing wireless powering solutions for implantable devices with simultaneous real-time imaging in MRI-guided surgical suites. Finally in the last section, we model endovascular MRI coil coupling during RF transmit. FEM models for a series-resonant multimode coil and quadrature birdcage coil fields are developed and computationally efficient, circuit and full-wave simulations are used to model inductive coupling. The Bloch Siegert B1 mapping sequence is used for validating at 24, 28 and 34 microT background excitation. Quantitative performance metrics are successfully predicted and the role of simulation in geometric optimization is demonstrated. In a pig study, we demonstrate navigation of a catheter, with tip-tracking and high-resolution intravascular imaging, through the vasculature into the heart, followed by contextual visualization. A potentially significant application is in MRI-guided cardiac ablation procedures.

Increasing throughput of multiplexed electrical bus in pipe-lined architecture

DOEpatents

Asaad, Sameh; Brezzo, Bernard V; Kapur, Mohit

2014-05-27

Techniques are disclosed for increasing the throughput of a multiplexed electrical bus by exploiting available pipeline stages of a computer or other system. For example, a method for increasing a throughput of an electrical bus that connects at least two devices in a system comprises introducing at least one signal hold stage in a signal-receiving one of the two devices, such that a maximum frequency at which the two devices are operated is not limited by a number of cycles of an operating frequency of the electrical bus needed for a signal to propagate from a signal-transmitting one of the two devices to the signal-receiving one of the two devices. Preferably, the signal hold stage introduced in the signal-receiving one of the two devices is a pipeline stage re-allocated from the signal-transmitting one of the two devices.

Game theoretic wireless resource allocation for H.264 MGS video transmission over cognitive radio networks

NASA Astrophysics Data System (ADS)

Fragkoulis, Alexandros; Kondi, Lisimachos P.; Parsopoulos, Konstantinos E.

2015-03-01

We propose a method for the fair and efficient allocation of wireless resources over a cognitive radio system network to transmit multiple scalable video streams to multiple users. The method exploits the dynamic architecture of the Scalable Video Coding extension of the H.264 standard, along with the diversity that OFDMA networks provide. We use a game-theoretic Nash Bargaining Solution (NBS) framework to ensure that each user receives the minimum video quality requirements, while maintaining fairness over the cognitive radio system. An optimization problem is formulated, where the objective is the maximization of the Nash product while minimizing the waste of resources. The problem is solved by using a Swarm Intelligence optimizer, namely Particle Swarm Optimization. Due to the high dimensionality of the problem, we also introduce a dimension-reduction technique. Our experimental results demonstrate the fairness imposed by the employed NBS framework.

7 CFR 1767.22 - Other income and deductions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Cooperative Capital Credits 424Other Capital Credits and Patronage Capital Allocations 425Miscellaneous... Transmission Cooperative Capital Credits This account shall be credited with the annual capital furnished the power supply cooperative through payment of power bills. The amount of capital furnished the power...

7 CFR 1767.22 - Other income and deductions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Cooperative Capital Credits 424Other Capital Credits and Patronage Capital Allocations 425Miscellaneous... Transmission Cooperative Capital Credits This account shall be credited with the annual capital furnished the power supply cooperative through payment of power bills. The amount of capital furnished the power...

Design of a stabilized, compact gimbal for space-based free space optical communications (FSOC)

NASA Astrophysics Data System (ADS)

Cline, A.; Shubert, P.; McNally, J.; Jacka, N.; Pierson, R.

2017-02-01

Data transmits via optical communications through fibers at 10's of Terabits per second. Given the recent rapid explosion for bandwidth and competing demand for radio frequency (RF) spectrum allocations among differing interests, the need for space-based free space optical communications (FSOC) systems is ever increasing. FSOC systems offer advantages of higher data rates, smaller size and weight, narrower beam divergence, and lower power than RF systems. Lightweight, small form factor, and high performance two-axis gimbals are of strong interest for satellite FSOC applications. Small gimbal and optical terminal designs are important for widespread implementation of optical communications systems; in particular, for satellite-to-satellite crosslinks where the advantages of more secure communications links (Lower Probability of Intercept (LPI)/Lower Probability of Detect (LPD)) are very important. We developed design concepts for a small gimbal focusing on the use of commercial off-the-shelf (COTS) subsystems to establish their feasible implementation against the pointing stabilization, size, weight and power (SWaP), and performance challenges. The design drivers for the gimbal were weight, the elevation and azimuth field of regards, the form factor envelope (1U CubeSats), 100 μrad pointing accuracy, and 10 degrees per second slew capability. Innovations required in this development included a continuous fiber passed through an Azimuth Fiber Wrap and Elevation Fiber Wrap, overcoming typical mechanical and stress related limitations encountered with fiber optic cable wraps. In this presentation, we describe the configuration trades and design of such a gimbal.

Evaluation of power system security and development of transmission pricing method

NASA Astrophysics Data System (ADS)

Kim, Hyungchul

The electric power utility industry is presently undergoing a change towards the deregulated environment. This has resulted in unbundling of generation, transmission and distribution services. The introduction of competition into unbundled electricity services may lead system operation closer to its security boundaries resulting in smaller operating safety margins. The competitive environment is expected to lead to lower price rates for customers and higher efficiency for power suppliers in the long run. Under this deregulated environment, security assessment and pricing of transmission services have become important issues in power systems. This dissertation provides new methods for power system security assessment and transmission pricing. In power system security assessment, the following issues are discussed (1) The description of probabilistic methods for power system security assessment; (2) The computation time of simulation methods; (3) on-line security assessment for operation. A probabilistic method using Monte-Carlo simulation is proposed for power system security assessment. This method takes into account dynamic and static effects corresponding to contingencies. Two different Kohonen networks, Self-Organizing Maps and Learning Vector Quantization, are employed to speed up the probabilistic method. The combination of Kohonen networks and Monte-Carlo simulation can reduce computation time in comparison with straight Monte-Carlo simulation. A technique for security assessment employing Bayes classifier is also proposed. This method can be useful for system operators to make security decisions during on-line power system operation. This dissertation also suggests an approach for allocating transmission transaction costs based on reliability benefits in transmission services. The proposed method shows the transmission transaction cost of reliability benefits when transmission line capacities are considered. The ratio between allocation by transmission line capacity-use and allocation by reliability benefits is computed using the probability of system failure.

24. INTERIOR OF CENTRAL ROOM. BASE POWER PANEL VISIBLE ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. INTERIOR OF CENTRAL ROOM. BASE POWER PANEL VISIBLE ON RIGHT WALL OF HALLWAY. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

76 FR 69712 - Application To Export Electric Energy; BP Energy Company

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-09

... DEPARTMENT OF ENERGY [OE Docket No. EA-315-A] Application To Export Electric Energy; BP Energy.... SUMMARY: BP Energy Company (BP Energy) has applied to renew its authority to transmit electric energy from... BP Energy to transmit electric energy from the United States to Canada as a power marketer for a five...

47 CFR 15.709 - General technical requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... to the transmit antenna. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of... from the TVBD shall not be greater than the following values when measured in any 100 kHz band during...

47 CFR 15.709 - General technical requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... to the transmit antenna. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of... from the TVBD shall not be greater than the following values when measured in any 100 kHz band during...

47 CFR 15.709 - General technical requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... to the transmit antenna. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of... from the TVBD shall not be greater than the following values when measured in any 100 kHz band during...

47 CFR 15.709 - General technical requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... to the transmit antenna. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of... 100 kHz band during any time interval of continuous transmission: (i) Fixed devices: 12.2 dBm. (ii...

75 FR 75994 - Application To Export Electric Energy; Sempra Energy Trading LLC

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... DEPARTMENT OF ENERGY [OE Docket No. EA-191-D] Application To Export Electric Energy; Sempra Energy... application. SUMMARY: Sempra Energy Trading LLC (SET) has applied to renew its authority to transmit electric... transmit electric energy from the United States to Canada for a two- year term as a power marketer using...

AIDS funding: competing needs and the politics of priorities.

PubMed

Krieger, N

1988-01-01

Despite the Department of Health and Human Service's 1983 claim that AIDS is the nation's "number one health priority," funding for AIDS research, prevention, and treatment remains inadequate. Worse, it is often marshaled from or juxtaposed against other necessary health allocations. Consequent AIDS-related resource crises include diverting funds for research on other diseases to AIDS investigations, propping up AIDS prevention efforts at the expense of traditional sexually transmitted disease control programs, and pitting the health needs of AIDS patients against the needs of those seeking other urgent health services, e.g., prenatal care. While this forced competition typically is blamed on fiscal constraints, examination of federal spending priorities suggests that it results principally from Reagan Administration policies. This Administration has consistently boosted military spending at the expense of social and health services, and has deliberately undermined efforts to obtain sufficient and new allocations for AIDS. In order to avert political divisions spurred by competition for currently scarce resources, AIDS and other health activists together must argue that excessive military allocations must be shifted to health research and services, and that a national health program must be implemented, if AIDS programs are to be funded appropriately without jeopardizing other necessary health initiatives.

A preliminary design for a satellite power system

NASA Technical Reports Server (NTRS)

Enriquez, Clara V.; Kokaly, Ray; Nandi, Saumya; Timmons, Mike; Garrard, Mark; Mercado, Rommel; Rogers, Brian; Ugaz, Victor

1991-01-01

Outlined here is a preliminary design for a Solar Power Satellite (SPS) system. The SPS will provide a clean, reliable source of energy for mass consumption. The system will use satellites in geostationary orbits around the Earth to capture the sun's energy. The intercepted sunlight will be converted to laser beam energy which can be transmitted to the Earth's surface. Ground systems on the Earth will convert the transmissions from space into electric power. The preliminary design for the SPS consists of one satellite in orbit around the Earth transmitting to one ground station. The SPs technology uses multi-layer solar cell technology arranged on a 20 sq km planar array to intercept sunlight and convert it to an electric voltage. Power conditioning devices then send the electricity to a laser, which transmits the power to the surface of the Earth. A ground station will convert the beam into electricity. Construction will take place in low Earth orbit and array sections, 20 in total, will be sailed on the solar wind out to the GEO location in 150 days. These individual transportation sections are referred to as solar sailing panels (SSAPs). The primary truss elements used to support the arrays are composed on composite tubular members in a pentahedral arrangement. Smart segments consisting of passive and active damping devices will increase the control of dynamic SPS modes.

Radiofrequency energy deposition and radiofrequency power requirements in parallel transmission with increasing distance from the coil to the sample.

PubMed

Deniz, Cem M; Vaidya, Manushka V; Sodickson, Daniel K; Lattanzi, Riccardo

2016-01-01

We investigated global specific absorption rate (SAR) and radiofrequency (RF) power requirements in parallel transmission as the distance between the transmit coils and the sample was increased. We calculated ultimate intrinsic SAR (UISAR), which depends on object geometry and electrical properties but not on coil design, and we used it as the reference to compare the performance of various transmit arrays. We investigated the case of fixing coil size and increasing the number of coils while moving the array away from the sample, as well as the case of fixing coil number and scaling coil dimensions. We also investigated RF power requirements as a function of lift-off, and tracked local SAR distributions associated with global SAR optima. In all cases, the target excitation profile was achieved and global SAR (as well as associated maximum local SAR) decreased with lift-off, approaching UISAR, which was constant for all lift-offs. We observed a lift-off value that optimizes the balance between global SAR and power losses in coil conductors. We showed that, using parallel transmission, global SAR can decrease at ultra high fields for finite arrays with a sufficient number of transmit elements. For parallel transmission, the distance between coils and object can be optimized to reduce SAR and minimize RF power requirements associated with homogeneous excitation. © 2015 Wiley Periodicals, Inc.

Networked Rectenna Array for Smart Material Actuators

NASA Technical Reports Server (NTRS)

Choi, Sang H.; Golembiewski, Walter T.; Song, Kyo D.

2000-01-01

The concept of microwave-driven smart material actuators is envisioned as the best option to alleviate the complexity associated with hard-wired control circuitry. Networked rectenna patch array receives and converts microwave power into a DC power for an array of smart actuators. To use microwave power effectively, the concept of a power allocation and distribution (PAD) circuit is adopted for networking a rectenna/actuator patch array. The PAD circuit is imbedded into a single embodiment of rectenna and actuator array. The thin-film microcircuit embodiment of PAD circuit adds insignificant amount of rigidity to membrane flexibility. Preliminary design and fabrication of PAD circuitry that consists of a few nodal elements were made for laboratory testing. The networked actuators were tested to correlate the network coupling effect, power allocation and distribution, and response time. The features of preliminary design are 16-channel computer control of actuators by a PCI board and the compensator for a power failure or leakage of one or more rectennas.

Evaluation of feasibility of 1.5 Tesla prostate MRI using body coil RF transmit in a patient with an implanted vagus nerve stimulator.

PubMed

Favazza, Christopher P; Edmonson, Heidi A; Ma, Chi; Shu, Yunhong; Felmlee, Joel P; Watson, Robert E; Gorny, Krzysztof R

2017-11-01

To assess risks of RF-heating of a vagus nerve stimulator (VNS) during 1.5 T prostate MRI using body coil transmit and to compare these risks with those associated with MRI head exams using a transmit/receive head coil. Spatial distributions of radio-frequency (RF) B1 fields generated by transmit/receive (T/R) body and head coils were empirically assessed along the long axis of a 1.5 T MRI scanner bore. Measurements were obtained along the center axis of the scanner and laterally offset by 15 cm (body coil) and 7 cm (head coil). RF-field measurements were supplemented with direct measurements of RF-heating of 15 cm long copper wires affixed to and submerged in the "neck" region of the gelled saline-filled (sodium chloride and polyacrylic acid) "head-and-torso" phantom. Temperature elevations at the lead tips were measured using fiber-optic thermometers with the phantom positioned at systematically increased distances from the scanner isocenter. B1 field measurements demonstrated greater than 10 dB reduction in RF power at distances beyond 28 cm and 24 cm from isocenter for body and head coil, respectively. Moreover, RF power from body coil transmit at distances greater than 32 cm from isocenter was found to be lower than from the RF power from head coil transmit measured at locations adjacent to the coil array at its opening. Correspondingly, maximum temperature elevations at the tips of the copper wires decreased with increasing distance from isocenter - from 7.4°C at 0 cm to no appreciable heating at locations beyond 40 cm. For the particular scanner model evaluated in this study, positioning an implanted VNS farther than 32 cm from isocenter (configuration achievable for prostate exams) can reduce risks of RF-heating resulting from the body coil transmit to those associated with using a T/R head coil. © 2017 American Association of Physicists in Medicine.

Fuzzy-logic based Q-Learning interference management algorithms in two-tier networks

NASA Astrophysics Data System (ADS)

Xu, Qiang; Xu, Zezhong; Li, Li; Zheng, Yan

2017-10-01

Unloading from macrocell network and enhancing coverage can be realized by deploying femtocells in the indoor scenario. However, the system performance of the two-tier network could be impaired by the co-tier and cross-tier interference. In this paper, a distributed resource allocation scheme is studied when each femtocell base station is self-governed and the resource cannot be assigned centrally through the gateway. A novel Q-Learning interference management scheme is proposed, that is divided into cooperative and independent part. In the cooperative algorithm, the interference information is exchanged between the cell-edge users which are classified by the fuzzy logic in the same cell. Meanwhile, we allocate the orthogonal subchannels to the high-rate cell-edge users to disperse the interference power when the data rate requirement is satisfied. The resource is assigned directly according to the minimum power principle in the independent algorithm. Simulation results are provided to demonstrate the significant performance improvements in terms of the average data rate, interference power and energy efficiency over the cutting-edge resource allocation algorithms.

Electric vehicle station equipment for grid-integrated vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kempton, Willett; Kiamilev, Fouad; McGee, Rodney

Methods, systems, and apparatus transferring power between the grid and an electric vehicle are disclosed. The apparatus may include at least one vehicle communication port for interfacing with electric vehicle equipment (EVE) and a processor coupled to the at least one vehicle communication port to establish communication with the EVE, receive EVE attributes from the EVE, and transmit electric vehicle station equipment (EVSE) attributes to the EVE. Power may be transferred between the grid and the electric vehicle by maintaining EVSE attributes, establishing communication with the EVE, and transmitting the EVSE maintained attributes to the EVE.

Multi-turn transmit coil to increase b1 efficiency in current source amplification.

PubMed

Gudino, N; Griswold, M A

2013-04-01

A multi-turn transmit surface coil design was presented to improve B1 efficiency when used with current source amplification. Three different coil designs driven by an on-coil current-mode class-D amplifier with current envelope feedback were tested on the benchtop and through imaging in a 1.5 T scanner. Case temperature of the power field-effect transistor at the amplifier output stage was measured to evaluate heat dissipation for the different current levels and coil configurations. In addition, a lower power rated device was tested to exploit the potential gain in B1 obtained with the multi-turn coil. As shown both on the benchtop and in a 1.5 T scanner, B1 was increased by almost 3-fold without increasing heat dissipation on the power device at the amplifier's output using a multi-turn surface coil. Similar gain was obtained when connecting a lower power rated field-effect transistor to the multi-turn coil. In addition to reduce heat dissipation per B1 in the device, higher B1 per current efficiency allows the use of field-effect transistors with lower current ratings and lower port capacitances, which could improve the overall performance of the on-coil current source transmit system. Copyright © 2013 Wiley Periodicals, Inc.

Multi-turn transmit coil to increase B1 efficiency in current source amplification

PubMed Central

Gudino, N.; Griswold, M.A.

2013-01-01

Purpose A multi-turn transmit surface coil design was presented to improve B1 efficiency when used with current source amplification. Methods Three different coil designs driven by an on-coil current-mode class-D (CMCD) amplifier with current envelope feedback were tested on the benchtop and through imaging in a 1.5 T scanner. Case temperature of the power field-effect transistor (FET) at the amplifier output stage was measured to evaluate heat dissipation for the different current levels and coil configurations. In addition, a lower power rated device was tested to exploit the potential gain in B1 obtained with the multi-turn coil. Results As shown both on the benchtop and in a 1.5 T scanner, B1 was increased by almost three-fold without increasing heat dissipation on the power device at the amplifier's output using a multi-turn surface coil. Similar gain was obtained when connecting a lower power rated FET to the multi-turn coil. Conclusion In addition to reduce heat dissipation per B1 in the device, higher B1 per current efficiency allows the use of FETs with lower current ratings and lower port capacitances which could improve the overall performance of the on-coil current source transmit system. PMID:23401060

25. PRIMARY POWER TRANSMISSION BELT HOLES IN 1st FLOOR MILL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. PRIMARY POWER TRANSMISSION BELT HOLES IN 1st FLOOR MILL NO. 1 CEILING. WATER-POWERED MACHINERY LOCATED IN BASEMENT RAN LEATHER BELTS THROUGH THESE HOLES. POWER WAS THEN TRANSMITTED TO SHAFTS AND PULLEYS TO RUN MACHINERY ON MILL FLOORS. - Prattville Manufacturing Company, Number One, 242 South Court Street, Prattville, Autauga County, AL

Phase coded, micro-power impulse radar motion sensor

DOEpatents

McEwan, Thomas E.

1996-01-01

A motion sensing, micro-power impulse radar MIR impresses on the transmitted signal, or the received pulse timing signal, one or more frequencies lower than the pulse repetition frequency, that become intermediate frequencies in a "IF homodyne" receiver. Thus, many advantages of classical RF receivers can be thereby be realized with ultra-wide band radar. The sensor includes a transmitter which transmits a sequence of electromagnetic pulses in response to a transmit timing signal at a nominal pulse repetition frequency. A receiver samples echoes of the sequence of electromagnetic pulses from objects within the field with controlled timing, in response to a receive timing signal, and generates a sample signal in response to the samples. A timing circuit supplies the transmit timing signal to the transmitter and supplies the receive timing signal to the receiver. The relative timing of the transmit timing signal and the receive timing signal is modulated between a first relative delay and a second relative delay at an intermediate frequency, causing the receiver to sample the echoes such that the time between transmissions of pulses in the sequence and samples by the receiver is modulated at the intermediate frequency. Modulation may be executed by modulating the pulse repetition frequency which drives the transmitter, by modulating the delay circuitry which controls the relative timing of the sample strobe, or by modulating amplitude of the transmitted pulses. The electromagnetic pulses will have a nominal center frequency related to pulse width, and the first relative delay and the second relative delay between which the timing signals are modulated, differ by less than the nominal pulse width, and preferably by about one-quarter wavelength at the nominal center frequency of the transmitted pulses.

Phase coded, micro-power impulse radar motion sensor

DOEpatents

McEwan, T.E.

1996-05-21

A motion sensing, micro-power impulse radar MIR impresses on the transmitted signal, or the received pulse timing signal, one or more frequencies lower than the pulse repetition frequency, that become intermediate frequencies in a ``IF homodyne`` receiver. Thus, many advantages of classical RF receivers can be thereby be realized with ultra-wide band radar. The sensor includes a transmitter which transmits a sequence of electromagnetic pulses in response to a transmit timing signal at a nominal pulse repetition frequency. A receiver samples echoes of the sequence of electromagnetic pulses from objects within the field with controlled timing, in response to a receive timing signal, and generates a sample signal in response to the samples. A timing circuit supplies the transmit timing signal to the transmitter and supplies the receive timing signal to the receiver. The relative timing of the transmit timing signal and the receive timing signal is modulated between a first relative delay and a second relative delay at an intermediate frequency, causing the receiver to sample the echoes such that the time between transmissions of pulses in the sequence and samples by the receiver is modulated at the intermediate frequency. Modulation may be executed by modulating the pulse repetition frequency which drives the transmitter, by modulating the delay circuitry which controls the relative timing of the sample strobe, or by modulating amplitude of the transmitted pulses. The electromagnetic pulses will have a nominal center frequency related to pulse width, and the first relative delay and the second relative delay between which the timing signals are modulated, differ by less than the nominal pulse width, and preferably by about one-quarter wavelength at the nominal center frequency of the transmitted pulses. 5 figs.

MTR,TRA603. EXPERIMENTERS' SPACE ALLOCATIONS IN BASEMENT AS OF 1963. SHIELDED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR,TRA-603. EXPERIMENTERS' SPACE ALLOCATIONS IN BASEMENT AS OF 1963. SHIELDED CUBICLES WERE IDENTIFIED BY SPONSORING LABORATORY AND ITS TEST HOLE NUMBER IN THE REACTOR, IE, "KAPL HB-1" SIGNIFIED KNOLLS ATOMIC POWER LABORATORY, HORIZONTAL BEAM NO. 1. "WAPD" WAS WESTINGHOUSE ATOMIC POWER DIVISION. CATCH TANKS AND SAMPLE STATIONS FOR TEST LOOPS WERE ASSOCIATED WITH THESE CUBICLES. NOTE DESKS, STORAGE CABINETS, SWITCH GEAR, INSTRUMENT PANELS. PHILLIPS PETROLEUM COMPANY MTR-E-5205, 4/1963. INL INDEX NO. 531-0603-00-706-009757, REV. 5. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Gender Discrimination in the Allocation of Migrant Household Resources.

PubMed

Antman, Francisca M

2015-07-01

This paper considers the relationship between international migration and gender discrimination through the lens of decision-making power over intrahousehold resource allocation. The endogeneity of migration is addressed with a difference-in-differences style identification strategy and a model with household fixed effects. The results suggest that while a migrant household head is away, a greater share of resources is spent on girls relative to boys and his spouse commands greater decision-making power. Once the head returns home, however, a greater share of resources goes to boys and there is suggestive evidence of greater authority for the head of household.

78 FR 27178 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-09

... Generation and Transmission cooperatives (G&T's) that generate or purchase power and transmit the power to the distribution systems. All RUS and G&T borrowers will enter into a Wholesale Power Contract with... the credit quality and credit worthiness of loans and loan guarantees to G&T borrowers. RUS works...

75 FR 75994 - Application To Export Electric Energy; NRG Power Marketing LLC

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... Marketing LLC AGENCY: Office of Electricity Delivery and Energy Reliability, DOE. ACTION: Notice of application. SUMMARY: NRG Power Marketing LLC (NRGPML) has applied to renew its authority to transmit electric... to Canada would be surplus energy purchased from electric utilities, Federal power marketing agencies...

Supplying the power requirements to a sensor network using radio frequency power transfer.

PubMed

Percy, Steven; Knight, Chris; Cooray, Francis; Smart, Ken

2012-01-01

Wireless power transmission is a method of supplying power to small electronic devices when there is no wired connection. One way to increase the range of these systems is to use a directional transmitting antenna, the problem with this approach is that power can only be transmitted through a narrow beam and directly forward, requiring the transmitter to always be aligned with the sensor node position. The work outlined in this article describes the design and testing of an autonomous radio frequency power transfer system that is capable of rotating the base transmitter to track the position of sensor nodes and transferring power to that sensor node. The system's base station monitors the node's energy levels and forms a charge queue to plan charging order and maintain energy levels of the nodes. Results show a radio frequency harvesting circuit with a measured S11 value of -31.5 dB and a conversion efficiency of 39.1%. Simulation and experimentation verified the level of power transfer and efficiency. The results of this work show a small network of three nodes with different storage types powered by a central base node.

IDMA-Based MAC Protocol for Satellite Networks with Consideration on Channel Quality

PubMed Central

2014-01-01

In order to overcome the shortcomings of existing medium access control (MAC) protocols based on TDMA or CDMA in satellite networks, interleave division multiple access (IDMA) technique is introduced into satellite communication networks. Therefore, a novel wide-band IDMA MAC protocol based on channel quality is proposed in this paper, consisting of a dynamic power allocation algorithm, a rate adaptation algorithm, and a call admission control (CAC) scheme. Firstly, the power allocation algorithm combining the technique of IDMA SINR-evolution and channel quality prediction is developed to guarantee high power efficiency even in terrible channel conditions. Secondly, the effective rate adaptation algorithm, based on accurate channel information per timeslot and by the means of rate degradation, can be realized. What is more, based on channel quality prediction, the CAC scheme, combining the new power allocation algorithm, rate scheduling, and buffering strategies together, is proposed for the emerging IDMA systems, which can support a variety of traffic types, and offering quality of service (QoS) requirements corresponding to different priority levels. Simulation results show that the new wide-band IDMA MAC protocol can make accurate estimation of available resource considering the effect of multiuser detection (MUD) and QoS requirements of multimedia traffic, leading to low outage probability as well as high overall system throughput. PMID:25126592

Artificial Intelligence Based Control Power Optimization on Tailless Aircraft. [ARMD Seedling Fund Phase I

NASA Technical Reports Server (NTRS)

Gern, Frank; Vicroy, Dan D.; Mulani, Sameer B.; Chhabra, Rupanshi; Kapania, Rakesh K.; Schetz, Joseph A.; Brown, Derrell; Princen, Norman H.

2014-01-01

Traditional methods of control allocation optimization have shown difficulties in exploiting the full potential of controlling large arrays of control devices on innovative air vehicles. Artificial neutral networks are inspired by biological nervous systems and neurocomputing has successfully been applied to a variety of complex optimization problems. This project investigates the potential of applying neurocomputing to the control allocation optimization problem of Hybrid Wing Body (HWB) aircraft concepts to minimize control power, hinge moments, and actuator forces, while keeping system weights within acceptable limits. The main objective of this project is to develop a proof-of-concept process suitable to demonstrate the potential of using neurocomputing for optimizing actuation power for aircraft featuring multiple independently actuated control surfaces. A Nastran aeroservoelastic finite element model is used to generate a learning database of hinge moment and actuation power characteristics for an array of flight conditions and control surface deflections. An artificial neural network incorporating a genetic algorithm then uses this training data to perform control allocation optimization for the investigated aircraft configuration. The phase I project showed that optimization results for the sum of required hinge moments are improved by more than 12% over the best Nastran solution by using the neural network optimization process.

78 FR 14779 - Application to Export Electric Energy; Shell Energy North America (US), L.P.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-07

... DEPARTMENT OF ENERGY [OE Docket No. EA-339-A] Application to Export Electric Energy; Shell Energy... its authority to transmit electric energy from the United States to Canada pursuant to section 202(e... transmit electric energy from the United States to Canada as a power marketer for a five-year term using...

78 FR 14778 - Application to Export Electric Energy; Shell Energy North America (US), L.P.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-07

... DEPARTMENT OF ENERGY [OE Docket No. EA-338-A] Application to Export Electric Energy; Shell Energy... its authority to transmit electric energy from the United States to Mexico pursuant to section 202(e... transmit electric energy from the United States to Mexico as a power marketer for a five-year term using...

Time for a new budget allocation model for hospital care in Stockholm?

PubMed

Andersson, Per-Åke; Bruce, Daniel; Walander, Anders; Viberg, Inga

2011-03-01

In Stockholm County Council (SLL), budgets for hospital care have been allocated to geographically responsible authorities for a long time. This hospital care includes all publicly financed specialist care, also privately owned hospitals, except private practitioner care. The old needs-index model, a 6D capitation matrix based on demography and socio-economy, was generated on linked individual data for 1994-96. In this paper the power of the old allocation model is evaluated by the use of new data for 2006. The analysis shows that most of the socioeconomic variables have lost their descriptive power in 10 years. Using a methodical search we also find an improved need-based allocation model for hospital care using the new data for 2006. By focusing on costly diagnoses, where the descriptive power has increased between 1996 and 2006, and by using some new socioeconomic variables, and by relying on birth and death prognoses, we are able to generate a matrix model with much higher coefficients-of-determinations in 1 year predictions. In addition, a more careful modelling of multi-morbidity, part-of-the-year inhabitants, episode definition and cost transformation is developed. The area-level cost residuals of registered versus predicted costs show stable signs over the years, indicating unexplained systematics. For the reduction of the residuals, accepting proven inpatient diagnoses but not the full costs, a mixed capitation/fee-for-service strategy is discussed. Once equivalent (e.g. full-year) observations are determined, the link between background and consumption is not on individual-level but on cell-level, as in current resource allocation studies in the United Kingdom.

Energy-efficient orthogonal frequency division multiplexing-based passive optical network based on adaptive sleep-mode control and dynamic bandwidth allocation

NASA Astrophysics Data System (ADS)

Zhang, Chongfu; Xiao, Nengwu; Chen, Chen; Yuan, Weicheng; Qiu, Kun

2016-02-01

We propose an energy-efficient orthogonal frequency division multiplexing-based passive optical network (OFDM-PON) using adaptive sleep-mode control and dynamic bandwidth allocation. In this scheme, a bidirectional-centralized algorithm named the receiver and transmitter accurate sleep control and dynamic bandwidth allocation (RTASC-DBA), which has an overall bandwidth scheduling policy, is employed to enhance the energy efficiency of the OFDM-PON. The RTASC-DBA algorithm is used in an optical line terminal (OLT) to control the sleep mode of an optical network unit (ONU) sleep and guarantee the quality of service of different services of the OFDM-PON. The obtained results show that, by using the proposed scheme, the average power consumption of the ONU is reduced by ˜40% when the normalized ONU load is less than 80%, compared with the average power consumption without using the proposed scheme.

Claim Your Powers.

ERIC Educational Resources Information Center

Update on Law-Related Education, 1986

1986-01-01

Presents a game which has students interpret Articles I, II, and III of the U.S. Constitution to understand the allocation of powers among the 3 branches of government. The game helps students understand the interaction between the 3 branches of government, stressing the separation of powers and the system of checks and balances. (JDH)

Performance Evaluation of CMUT-Based Ultrasonic Transformers for Galvanic Isolation.

PubMed

Heller, Jacques; Boulme, Audren; Alquier, Daniel; Ngo, Sophie; Certon, Dominique

2018-04-01

This paper presents the development of a novel acoustic transformer with high galvanic isolation dedicated to power switch triggering. The transformer is based on two capacitive micromachined ultrasonic transducers layered on each side of a silicon substrate; one is the primary circuit, and the other is the secondary circuit. The thickness mode resonance of the substrate is leveraged to transmit the triggering signal. The fabrication and characterization of an initial prototype is presented in this paper. All experimental results are discussed, from the electrical impedance measurements to the power efficiency measurements, for different electrical load conditions. A comparison with a specifically developed finite-element method model is done. Simulations are finally used to identify the optimization rules of this initial prototype. It is shown that the power efficiency can be increased from 35% to 60%, and the transmitted power can be increased from 1.6 to 45 mW/Volt.

An Efficient, Lossless Database for Storing and Transmitting Medical Images

NASA Technical Reports Server (NTRS)

Fenstermacher, Marc J.

1998-01-01

This research aimed in creating new compression methods based on the central idea of Set Redundancy Compression (SRC). Set Redundancy refers to the common information that exists in a set of similar images. SRC compression methods take advantage of this common information and can achieve improved compression of similar images by reducing their Set Redundancy. The current research resulted in the development of three new lossless SRC compression methods: MARS (Median-Aided Region Sorting), MAZE (Max-Aided Zero Elimination) and MaxGBA (Max-Guided Bit Allocation).

The dominance of big pharma: power.

PubMed

Edgar, Andrew

2013-05-01

The purpose of this paper is to provide a normative model for the assessment of the exercise of power by Big Pharma. By drawing on the work of Steven Lukes, it will be argued that while Big Pharma is overtly highly regulated, so that its power is indeed restricted in the interests of patients and the general public, the industry is still able to exercise what Lukes describes as a third dimension of power. This entails concealing the conflicts of interest and grievances that Big Pharma may have with the health care system, physicians and patients, crucially through rhetorical engagements with Patient Advocacy Groups that seek to shape public opinion, and also by marginalising certain groups, excluding them from debates over health care resource allocation. Three issues will be examined: the construction of a conception of the patient as expert patient or consumer; the phenomenon of disease mongering; the suppression or distortion of debates over resource allocation.

Remote shock sensing and notification system

DOEpatents

Muralidharan, Govindarajan; Britton, Charles L.; Pearce, James; Jagadish, Usha; Sikka, Vinod K.

2008-11-11

A low-power shock sensing system includes at least one shock sensor physically coupled to a chemical storage tank to be monitored for impacts, and an RF transmitter which is in a low-power idle state in the absence of a triggering signal. The system includes interference circuitry including or activated by the shock sensor, wherein an output of the interface circuitry is coupled to an input of the RF transmitter. The interface circuitry triggers the RF transmitting with the triggering signal to transmit an alarm message to at least one remote location when the sensor senses a shock greater than a predetermined threshold. In one embodiment the shock sensor is a shock switch which provides an open and a closed state, the open state being a low power idle state.

Efficient data communication protocols for wireless networks

NASA Astrophysics Data System (ADS)

Zeydan, Engin

In this dissertation, efficient decentralized algorithms are investigated for cost minimization problems in wireless networks. For wireless sensor networks, we investigate both the reduction in the energy consumption and throughput maximization problems separately using multi-hop data aggregation for correlated data in wireless sensor networks. The proposed algorithms exploit data redundancy using a game theoretic framework. For energy minimization, routes are chosen to minimize the total energy expended by the network using best response dynamics to local data. The cost function used in routing takes into account distance, interference and in-network data aggregation. The proposed energy-efficient correlation-aware routing algorithm significantly reduces the energy consumption in the network and converges in a finite number of steps iteratively. For throughput maximization, we consider both the interference distribution across the network and correlation between forwarded data when establishing routes. Nodes along each route are chosen to minimize the interference impact in their neighborhood and to maximize the in-network data aggregation. The resulting network topology maximizes the global network throughput and the algorithm is guaranteed to converge with a finite number of steps using best response dynamics. For multiple antenna wireless ad-hoc networks, we present distributed cooperative and regret-matching based learning schemes for joint transmit beanformer and power level selection problem for nodes operating in multi-user interference environment. Total network transmit power is minimized while ensuring a constant received signal-to-interference and noise ratio at each receiver. In cooperative and regret-matching based power minimization algorithms, transmit beanformers are selected from a predefined codebook to minimize the total power. By selecting transmit beamformers judiciously and performing power adaptation, the cooperative algorithm is shown to converge to pure strategy Nash equilibrium with high probability throughout the iterations in the interference impaired network. On the other hand, the regret-matching learning algorithm is noncooperative and requires minimum amount of overhead. The proposed cooperative and regret-matching based distributed algorithms are also compared with centralized solutions through simulation results.

Extraordinary Sex Ratios: Cultural Effects on Ecological Consequences

PubMed Central

Molnár, Ferenc; Caraco, Thomas; Korniss, Gyorgy

2012-01-01

We model sex-structured population dynamics to analyze pairwise competition between groups differing both genetically and culturally. A sex-ratio allele is expressed in the heterogametic sex only, so that assumptions of Fisher’s analysis do not apply. Sex-ratio evolution drives cultural evolution of a group-associated trait governing mortality in the homogametic sex. The two-sex dynamics under resource limitation induces a strong Allee effect that depends on both sex ratio and cultural trait values. We describe the resulting threshold, separating extinction from positive growth, as a function of female and male densities. When initial conditions avoid extinction due to the Allee effect, different sex ratios cannot coexist; in our model, greater female allocation always invades and excludes a lesser allocation. But the culturally transmitted trait interacts with the sex ratio to determine the ecological consequences of successful invasion. The invading female allocation may permit population persistence at self-regulated equilibrium. For this case, the resident culture may be excluded, or may coexist with the invader culture. That is, a single sex-ratio allele in females and a cultural dimorphism in male mortality can persist; a low-mortality resident trait is maintained by father-to-son cultural transmission. Otherwise, the successfully invading female allocation excludes the resident allele and culture and then drives the population to extinction via a shortage of males. Finally, we show that the results obtained under homogeneous mixing hold, with caveats, in a spatially explicit model with local mating and diffusive dispersal in both sexes. PMID:22952669

Extraordinary sex ratios: cultural effects on ecological consequences.

PubMed

Molnár, Ferenc; Caraco, Thomas; Korniss, Gyorgy

2012-01-01

We model sex-structured population dynamics to analyze pairwise competition between groups differing both genetically and culturally. A sex-ratio allele is expressed in the heterogametic sex only, so that assumptions of Fisher's analysis do not apply. Sex-ratio evolution drives cultural evolution of a group-associated trait governing mortality in the homogametic sex. The two-sex dynamics under resource limitation induces a strong Allee effect that depends on both sex ratio and cultural trait values. We describe the resulting threshold, separating extinction from positive growth, as a function of female and male densities. When initial conditions avoid extinction due to the Allee effect, different sex ratios cannot coexist; in our model, greater female allocation always invades and excludes a lesser allocation. But the culturally transmitted trait interacts with the sex ratio to determine the ecological consequences of successful invasion. The invading female allocation may permit population persistence at self-regulated equilibrium. For this case, the resident culture may be excluded, or may coexist with the invader culture. That is, a single sex-ratio allele in females and a cultural dimorphism in male mortality can persist; a low-mortality resident trait is maintained by father-to-son cultural transmission. Otherwise, the successfully invading female allocation excludes the resident allele and culture and then drives the population to extinction via a shortage of males. Finally, we show that the results obtained under homogeneous mixing hold, with caveats, in a spatially explicit model with local mating and diffusive dispersal in both sexes.

Decompositions of injection patterns for nodal flow allocation in renewable electricity networks

NASA Astrophysics Data System (ADS)

Schäfer, Mirko; Tranberg, Bo; Hempel, Sabrina; Schramm, Stefan; Greiner, Martin

2017-08-01

The large-scale integration of fluctuating renewable power generation represents a challenge to the technical and economical design of a sustainable future electricity system. In this context, the increasing significance of long-range power transmission calls for innovative methods to understand the emerging complex flow patterns and to integrate price signals about the respective infrastructure needs into the energy market design. We introduce a decomposition method of injection patterns. Contrary to standard flow tracing approaches, it provides nodal allocations of link flows and costs in electricity networks by decomposing the network injection pattern into market-inspired elementary import/export building blocks. We apply the new approach to a simplified data-driven model of a European electricity grid with a high share of renewable wind and solar power generation.

47 CFR 90.542 - Broadband transmitting power limits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Antenna height (AAT) in meters(feet) Effective radiated power (ERP)(watts) Above 1372 (4500) 65 Above 1220... Bandwidth of 1 MHz or Less Antenna height (AAT) in meters(feet) Effective radiated power (ERP)(watts) Above... (3000) To 1067 (3500) 200 Above 763 (2500) To 915 (3000) 280 Above 610 (2000) To 763 (2500) 400 Above...

Multiple-Optimizing Dynamic Sensor Networks with MIMO Technology (PREPRINT)

DTIC Science & Technology

2010-06-01

a) where PAP is the power consumption dependent on the transmit power , cP is the power consumption dependent on the transceiver circuit...w’s parent p received new’s request, p adds new into its backbone list and sets d(p, new) = 2d; p sends the kowledge it holds to new

14 CFR Appendix I to Part 25 - Installation of an Automatic Takeoff Thrust Control System (ATTCS)

Code of Federal Regulations, 2010 CFR

2010-01-01

...) This appendix specifies additional requirements for installation of an engine power control system that... crew to increase thrust or power. I25.2Definitions. (a) Automatic Takeoff Thrust Control System (ATTCS... mechanical and electrical, that sense engine failure, transmit signals, actuate fuel controls or power levers...

Focus expansion and stability of the spread parameter estimate of the power law model for dispersal gradients

USDA-ARS?s Scientific Manuscript database

Empirical and mechanistic modeling indicate that aerially transmitted pathogens follow a power law, resulting in dispersive epidemic waves. The spread parameter (b) of the power law model, which defines the distance travelled by the epidemic wave front, has been found to be approximately 2 for sever...

47 CFR 90.1215 - Power limits.

Code of Federal Regulations, 2011 CFR

2011-10-01

...Bm/MHz. If transmitting antennas of directional gain greater than 9 dBi are used, both the maximum... the directional gain of the antenna exceeds 9 dBi. However, high power point-to-point and point-to... directional gain up to 26 dBi without any corresponding reduction in the maximum conducted output power or...

47 CFR 90.1215 - Power limits.

Code of Federal Regulations, 2014 CFR

2014-10-01

...Bm/MHz. If transmitting antennas of directional gain greater than 9 dBi are used, both the maximum... the directional gain of the antenna exceeds 9 dBi. However, high power point-to-point and point-to... directional gain up to 26 dBi without any corresponding reduction in the maximum conducted output power or...

47 CFR 90.1215 - Power limits.

Code of Federal Regulations, 2013 CFR

2013-10-01

...Bm/MHz. If transmitting antennas of directional gain greater than 9 dBi are used, both the maximum... the directional gain of the antenna exceeds 9 dBi. However, high power point-to-point and point-to... directional gain up to 26 dBi without any corresponding reduction in the maximum conducted output power or...

47 CFR 90.1215 - Power limits.

Code of Federal Regulations, 2012 CFR

2012-10-01

...Bm/MHz. If transmitting antennas of directional gain greater than 9 dBi are used, both the maximum... the directional gain of the antenna exceeds 9 dBi. However, high power point-to-point and point-to... directional gain up to 26 dBi without any corresponding reduction in the maximum conducted output power or...

Rotary Joints With Electrical Connections

NASA Technical Reports Server (NTRS)

Osborn, F. W.

1986-01-01

Power and data transmitted on many channels. Two different rotary joints equipped with electrical connections between rotating and stationary parts. One joint transmits axial thrust and serves as interface between spinning and nonspinning parts of Galileo spacecraft. Other is scanning (limitedrotation) joint that aims scientific instruments from nonspinning part. Selected features of both useful to designers of robots, advanced production equipment, and remotely controlled instruments.

Microwave-Driven Multifunctional Capability of Membrane Structures

NASA Technical Reports Server (NTRS)

Choi, Sang H.; Chu, Sang-Hyong; Song, Kyo D.; King, Glen C.

2002-01-01

A large, ultra lightweight space structure, such as solar sails and Gossamer spacecrafts, requires a distributed power source to alleviate wire networks, unlike the localized on-board power infrastructures typically found in most small spacecrafts. The concept of microwave-driven multifunctional capability for membrane structures is envisioned as the best option to alleviate the complexity associated with hard-wired control circuitry and on-board power infrastructures. A rectenna array based on a patch configuration for high voltage output was developed to drive membrane actuators, sensors, probes, or other devices. Networked patch rectenna array receives and converts microwave power into a DC power for an array of smart actuators. To use microwave power effectively, the concept of a power allocation and distribution (PAD) circuit is adopted for networking a rectenna/actuator patch array. The use of patch rectennas adds a significant amount of rigidity to membrane flexibility and they are relatively heavy. A dipole rectenna array (DRA) appears to be ideal for thin-film membrane structures, since DRA is flexible and light. Preliminary design and fabrication of PAD circuitry that consists of a few nodal elements were made for laboratory testing. The networked actuators were tested to correlate the network coupling effect, power allocation and distribution, and response time.

Range-gated field disturbance sensor with range-sensitivity compensation

DOEpatents

McEwan, T.E.

1996-05-28

A field disturbance sensor operates with relatively low power, provides an adjustable operating range, is not hypersensitive at close range, allows co-location of multiple sensors, and is inexpensive to manufacture. The sensor includes a transmitter that transmits a sequence of transmitted bursts of electromagnetic energy. The transmitter frequency is modulated at an intermediate frequency. The sequence of bursts has a burst repetition rate, and each burst has a burst width and comprises a number of cycles at a transmitter frequency. The sensor includes a receiver which receives electromagnetic energy at the transmitter frequency, and includes a mixer which mixes a transmitted burst with reflections of the same transmitted burst to produce an intermediate frequency signal. Circuitry, responsive to the intermediate frequency signal indicates disturbances in the sensor field. Because the mixer mixes the transmitted burst with reflections of the transmitted burst, the burst width defines the sensor range. The burst repetition rate is randomly or pseudorandomly modulated so that bursts in the sequence of bursts have a phase which varies. 8 figs.

Range-gated field disturbance sensor with range-sensitivity compensation

DOEpatents

McEwan, Thomas E.

1996-01-01

A field disturbance sensor operates with relatively low power, provides an adjustable operating range, is not hypersensitive at close range, allows co-location of multiple sensors, and is inexpensive to manufacture. The sensor includes a transmitter that transmits a sequence of transmitted bursts of electromagnetic energy. The transmitter frequency is modulated at an intermediate frequency. The sequence of bursts has a burst repetition rate, and each burst has a burst width and comprises a number of cycles at a transmitter frequency. The sensor includes a receiver which receives electromagnetic energy at the transmitter frequency, and includes a mixer which mixes a transmitted burst with reflections of the same transmitted burst to produce an intermediate frequency signal. Circuitry, responsive to the intermediate frequency signal indicates disturbances in the sensor field. Because the mixer mixes the transmitted burst with reflections of the transmitted burst, the burst width defines the sensor range. The burst repetition rate is randomly or pseudorandomly modulated so that bursts in the sequence of bursts have a phase which varies.

Loudness of steady sounds - A new theory

NASA Technical Reports Server (NTRS)

Howes, W. L.

1979-01-01

A new mathematical theory for calculating the loudness of steady sounds from power summation and frequency interaction, based on psychoacoustic and physiological information, assuems that loudness is a subjective measure of the electrical energy transmitted along the auditory nerve to the central nervous system. The auditory system consists of the mechanical part modeled by a bandpass filter with a transfer function dependent on the sound pressure, and the electrical part where the signal is transformed into a half-wave reproduction represented by the electrical power in impulsive discharges transmitted along neurons comprising the auditory nerve. In the electrical part the neurons are distributed among artificial parallel channels with frequency bandwidths equal to 'critical bandwidths for loudness', within which loudness is constant for constant sound pressure. The total energy transmitted to the central nervous system is the sum of the energy transmitted in all channels, and the loudness is proportional to the square root of the total filtered sound energy distributed over all channels. The theory explains many psychoacoustic phenomena such as audible beats resulting from closely spaced tones, interaction of sound stimuli which affect the same neurons affecting loudness, and of individually subliminal sounds becoming audible if they lie within the same critical band.

Performance Analysis of Transmit Diversity Systems with Multiple Antenna Replacement

NASA Astrophysics Data System (ADS)

Park, Ki-Hong; Yang, Hong-Chuan; Ko, Young-Chai

Transmit diversity systems based on orthogonal space-time block coding (OSTBC) usually suffer from rate loss and power spreading. Proper antenna selection scheme can help to more effectively utilize the transmit antennas and transmission power in such systems. In this paper, we propose a new antenna selection scheme for such systems based on the idea of antenna switching. In particular, targeting at reducing the number of pilot channels and RF chains, the transmitter now replaces the antennas with the lowest received SNR with unused ones if the output SNR of space time decoder at the receiver is below a certain threshold. With this new scheme, not only the number of pilot channels and RF chains to be implemented is decreased, the average amount of feedback information is also reduced. To analyze the performance of this scheme, we derive the exact integral closed form for the probability density function (PDF) of the received SNR. We show through numerical examples that the proposed scheme offers better performance than traditional OSTBC systems using all available transmitting antennas, with a small amount of feedback information. We also examine the effect of different antenna configuration and feedback delay.

Hoover Power Allocation Act of 2009

THOMAS, 111th Congress

Sen. Reid, Harry [D-NV

2009-12-16

Senate - 06/09/2010 Committee on Energy and Natural Resources Subcommittee on Water and Power. Hearings held. With printed Hearing: S.Hrg. 111-707. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

A METHOD FOR IN-SITU CHARACTERIZATION OF RF HEATING IN PARALLEL TRANSMIT MRI

PubMed Central

Alon, Leeor; Deniz, Cem Murat; Brown, Ryan; Sodickson, Daniel K.; Zhu, Yudong

2012-01-01

In ultra high field magnetic resonance imaging, parallel radio-frequency (RF) transmission presents both opportunities and challenges for specific absorption rate (SAR) management. On one hand, parallel transmission provides flexibility in tailoring electric fields in the body while facilitating magnetization profile control. On the other hand, it increases the complexity of energy deposition as well as possibly exacerbating local SAR by improper design or delivery of RF pulses. This study shows that the information needed to characterize RF heating in parallel transmission is contained within a local power correlation matrix. Building upon a calibration scheme involving a finite number of magnetic resonance thermometry measurements, the present work establishes a way of estimating the local power correlation matrix. Determination of this matrix allows prediction of temperature change for an arbitrary parallel transmit RF pulse. In the case of a three transmit coil MR experiment in a phantom, determination and validation of the power correlation matrix was conducted in less than 200 minutes with induced temperature changes of <4 degrees C. Further optimization and adaptation are possible, and simulations evaluating potential feasibility for in vivo use are presented. The method allows general characteristics indicative of RF coil/pulse safety determined in situ. PMID:22714806

Optical key system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hagans, K.G.; Clough, R.E.

2000-04-25

An optical key system comprises a battery-operated optical key and an isolated lock that derives both its operating power and unlock signals from the correct optical key. A light emitting diode or laser diode is included within the optical key and is connected to transmit a bit-serial password. The key user physically enters either the code-to-transmit directly, or an index to a pseudorandom number code, in the key. Such person identification numbers can be retained permanently, or ephemeral. When a send button is pressed, the key transmits a beam of light modulated with the password information. The modulated beam ofmore » light is received by a corresponding optical lock with a photovoltaic cell that produces enough power from the beam of light to operate a password-screen digital logic. In one application, an acceptable password allows a two watt power laser diode to pump ignition and timing information over a fiberoptic cable into a sealed engine compartment. The receipt of a good password allows the fuel pump, spark, and starter systems to each operate. Therefore, bypassing the lock mechanism as is now routine with automobile thieves is pointless because the engine is so thoroughly disabled.« less

Optical key system

DOEpatents

Hagans, Karla G.; Clough, Robert E.

2000-01-01

An optical key system comprises a battery-operated optical key and an isolated lock that derives both its operating power and unlock signals from the correct optical key. A light emitting diode or laser diode is included within the optical key and is connected to transmit a bit-serial password. The key user physically enters either the code-to-transmit directly, or an index to a pseudorandom number code, in the key. Such person identification numbers can be retained permanently, or ephemeral. When a send button is pressed, the key transmits a beam of light modulated with the password information. The modulated beam of light is received by a corresponding optical lock with a photovoltaic cell that produces enough power from the beam of light to operate a password-screen digital logic. In one application, an acceptable password allows a two watt power laser diode to pump ignition and timing information over a fiberoptic cable into a sealed engine compartment. The receipt of a good password allows the fuel pump, spark, and starter systems to each operate. Therefore, bypassing the lock mechanism as is now routine with automobile thieves is pointless because the engine is so thoroughly disabled.

26 CFR 20.2056(b)-5 - Marital deduction; life estate with power of appointment in surviving spouse.

Code of Federal Regulations, 2011 CFR

2011-04-01

... apportionment between the income and remainder beneficiaries of the total return of the trust and that meets the... absence, by the rules for the management of the trust property and the allocation of receipts and... assets and the rules provided for management of the trust that the allocation to income of such receipts...

Investigation of Optimal Control Allocation for Gust Load Alleviation in Flight Control

NASA Technical Reports Server (NTRS)

Frost, Susan A.; Taylor, Brian R.; Bodson, Marc

2012-01-01

Advances in sensors and avionics computation power suggest real-time structural load measurements could be used in flight control systems for improved safety and performance. A conventional transport flight control system determines the moments necessary to meet the pilot's command, while rejecting disturbances and maintaining stability of the aircraft. Control allocation is the problem of converting these desired moments into control effector commands. In this paper, a framework is proposed to incorporate real-time structural load feedback and structural load constraints in the control allocator. Constrained optimal control allocation can be used to achieve desired moments without exceeding specified limits on monitored load points. Minimization of structural loads by the control allocator is used to alleviate gust loads. The framework to incorporate structural loads in the flight control system and an optimal control allocation algorithm will be described and then demonstrated on a nonlinear simulation of a generic transport aircraft with flight dynamics and static structural loads.

Gender Discrimination in the Allocation of Migrant Household Resources*

PubMed Central

Antman, Francisca M.

2016-01-01

This paper considers the relationship between international migration and gender discrimination through the lens of decision-making power over intrahousehold resource allocation. The endogeneity of migration is addressed with a difference-in-differences style identification strategy and a model with household fixed effects. The results suggest that while a migrant household head is away, a greater share of resources is spent on girls relative to boys and his spouse commands greater decision-making power. Once the head returns home, however, a greater share of resources goes to boys and there is suggestive evidence of greater authority for the head of household. PMID:27546986

DAISY-DAMP: A distributed AI system for the dynamic allocation and management of power

NASA Technical Reports Server (NTRS)

Hall, Steven B.; Ohler, Peter C.

1988-01-01

One of the critical parameters that must be addressed when designing a loosely coupled Distributed AI SYstem (DAISY) has to do with the degree to which authority is centralized or decentralized. The decision to implement the Dynamic Allocation and Management of Power (DAMP) system as a network of cooperating agents mandated this study. The DAISY-DAMP problem is described; the component agents of the system are characterized; and the communication protocols system elucidated. The motivations and advantages in designing the system with authority decentralized is discussed. Progress in the area of Speech Act theory is proposed as playing a role in constructing decentralized systems.

A Bayesian adaptive design for biomarker trials with linked treatments.

PubMed

Wason, James M S; Abraham, Jean E; Baird, Richard D; Gournaris, Ioannis; Vallier, Anne-Laure; Brenton, James D; Earl, Helena M; Mander, Adrian P

2015-09-01

Response to treatments is highly heterogeneous in cancer. Increased availability of biomarkers and targeted treatments has led to the need for trial designs that efficiently test new treatments in biomarker-stratified patient subgroups. We propose a novel Bayesian adaptive randomisation (BAR) design for use in multi-arm phase II trials where biomarkers exist that are potentially predictive of a linked treatment's effect. The design is motivated in part by two phase II trials that are currently in development. The design starts by randomising patients to the control treatment or to experimental treatments that the biomarker profile suggests should be active. At interim analyses, data from treated patients are used to update the allocation probabilities. If the linked treatments are effective, the allocation remains high; if ineffective, the allocation changes over the course of the trial to unlinked treatments that are more effective. Our proposed design has high power to detect treatment effects if the pairings of treatment with biomarker are correct, but also performs well when alternative pairings are true. The design is consistently more powerful than parallel-groups stratified trials. This BAR design is a powerful approach to use when there are pairings of biomarkers with treatments available for testing simultaneously.

Estimating Transmitted-Signal Phase Variations for Uplink Array Antennas

NASA Technical Reports Server (NTRS)

Paal, Leslie; Mukai, Ryan; Vilntrotter, Victor; Cornish, Timothy; Lee, Dennis

2009-01-01

A method of estimating phase drifts of microwave signals distributed to, and transmitted by, antennas in an array involves the use of the signals themselves as phase references. The method was conceived as part of the solution of the problem of maintaining precise phase calibration required for proper operation of an array of Deep Space Network (DSN) antennas on Earth used for communicating with distant spacecraft at frequencies between 7 and 8 GHz. The method could also be applied to purely terrestrial phased-array radar and other radio antenna array systems. In the DSN application, the electrical lengths (effective signal-propagation path lengths) of the various branches of the system for distributing the transmitted signals to the antennas are not precisely known, and they vary with time. The variations are attributable mostly to thermal expansion and contraction of fiber-optic and electrical signal cables and to a variety of causes associated with aging of signal-handling components. The variations are large enough to introduce large phase drifts at the signal frequency. It is necessary to measure and correct for these phase drifts in order to maintain phase calibration of the antennas. A prior method of measuring phase drifts involves the use of reference-frequency signals separate from the transmitted signals. A major impediment to accurate measurement of phase drifts over time by the prior method is the fact that although DSN reference-frequency sources separate from the transmitting signal sources are stable and accurate enough for most DSN purposes, they are not stable enough for use in maintaining phase calibrations, as required, to within a few degrees over times as long as days or possibly even weeks. By eliminating reliance on the reference-frequency subsystem, the present method overcomes this impediment. In a DSN array to which the present method applies (see figure), the microwave signals to be transmitted are generated by exciters in a signal-processing center, then distributed to the antennas via optical fibers. At each antenna, the signals are used to drive a microwave power-amplifier train, the output of which is coupled to the antenna for transmission. A small fraction of the power-amplifier-train output is sent back to the signal-processing center along another optical fiber that is part of the same fiber-optic cable used to distribute the transmitted signal to the antenna. In the signal-processing center, the signal thus returned from each antenna is detected and its phase is compared with the phase of the signal sampled directly from the corresponding exciter. It is known, from other measurements, that the signal-propagation path length from the power-amplifier-train output port to the phase center of each antenna is sufficiently stable and, hence, that sampling the signal at the power-amplifier-train output port suffices for the purpose of characterizing the phase drift of the transmitted signal at the phase center of the antenna

Cluster Cooperation in Wireless-Powered Sensor Networks: Modeling and Performance Analysis.

PubMed

Zhang, Chao; Zhang, Pengcheng; Zhang, Weizhan

2017-09-27

A wireless-powered sensor network (WPSN) consisting of one hybrid access point (HAP), a near cluster and the corresponding far cluster is investigated in this paper. These sensors are wireless-powered and they transmit information by consuming the harvested energy from signal ejected by the HAP. Sensors are able to harvest energy as well as store the harvested energy. We propose that if sensors in near cluster do not have their own information to transmit, acting as relays, they can help the sensors in a far cluster to forward information to the HAP in an amplify-and-forward (AF) manner. We use a finite Markov chain to model the dynamic variation process of the relay battery, and give a general analyzing model for WPSN with cluster cooperation. Though the model, we deduce the closed-form expression for the outage probability as the metric of this network. Finally, simulation results validate the start point of designing this paper and correctness of theoretical analysis and show how parameters have an effect on system performance. Moreover, it is also known that the outage probability of sensors in far cluster can be drastically reduced without sacrificing the performance of sensors in near cluster if the transmit power of HAP is fairly high. Furthermore, in the aspect of outage performance of far cluster, the proposed scheme significantly outperforms the direct transmission scheme without cooperation.

Cluster Cooperation in Wireless-Powered Sensor Networks: Modeling and Performance Analysis

PubMed Central

Zhang, Chao; Zhang, Pengcheng; Zhang, Weizhan

2017-01-01

A wireless-powered sensor network (WPSN) consisting of one hybrid access point (HAP), a near cluster and the corresponding far cluster is investigated in this paper. These sensors are wireless-powered and they transmit information by consuming the harvested energy from signal ejected by the HAP. Sensors are able to harvest energy as well as store the harvested energy. We propose that if sensors in near cluster do not have their own information to transmit, acting as relays, they can help the sensors in a far cluster to forward information to the HAP in an amplify-and-forward (AF) manner. We use a finite Markov chain to model the dynamic variation process of the relay battery, and give a general analyzing model for WPSN with cluster cooperation. Though the model, we deduce the closed-form expression for the outage probability as the metric of this network. Finally, simulation results validate the start point of designing this paper and correctness of theoretical analysis and show how parameters have an effect on system performance. Moreover, it is also known that the outage probability of sensors in far cluster can be drastically reduced without sacrificing the performance of sensors in near cluster if the transmit power of HAP is fairly high. Furthermore, in the aspect of outage performance of far cluster, the proposed scheme significantly outperforms the direct transmission scheme without cooperation. PMID:28953231

Prevalence and intensity of soil transmitted helminths among school children of Mendera Elementary School, Jimma, Southwest Ethiopia.

PubMed

Tefera, Ephrem; Belay, Tariku; Mekonnen, Seleshi Kebede; Zeynudin, Ahmed; Belachew, Tefera

2017-01-01

Soil transmitted helminths are wide spread in developing countries and in Ethiopia the prevalence of STHs varies in different parts of the country. The aim of this study was to determine the prevalence and intensity of soil transmitted helminths among school children of Mendera Elementary School Jimma town, Southwestern Ethiopia. A cross-sectional study was conducted between March 29 and April 9, 2010 to determine the prevalence and intensity of soil transmitted helminths among elementary school children. The study participants were randomly selected from class enrollment list after proportional allocation of the total sample size to each grade. Data about the background characteristics were collected using structured questionnaire. The stool samples were examined by McMaster method for the egg count which was used to determine intensity of infection. Data were analyzed using SPSS for windows version 16 and p-value less than 5% was considered as statistically significant. Of the total 715 stool specimens examined, 346 were positive for at least one intestinal parasite making the prevalence 48.4%. The most prevalent parasites were Ascaris lumbricoides 169 (23.6%) and Trichuris trichiura 165 (23.1%). The prevalence of soil transmitted helminth in this study was 45.6% (326/715). There was statistically significant difference in the prevalence of Trichuriasis between those who use latrine always and who use sometimes (p = 0.010). Females are two times more likely to be positive for Ascaris than males (p = 0.039). Majority of the students had light infection of soil transmitted helminths and none of them had heavy intensity of infection of Trichuriasis and hookworms. Nearly half of the school children were infected with at least one STHs and majority of the students had light infection of soil transmitted helminths. Students who did not wash their hands after defecation were three times more likely to be positive for Ascaris infection than those who washed their hands after defecation. Therefore, measures like health information dissemination on the advantage of washing hands after defecation and on proper use of latrine should be taken into account to alleviate the problem.

Prevalence and intensity of soil transmitted helminths among school children of Mendera Elementary School, Jimma, Southwest Ethiopia

PubMed Central

Tefera, Ephrem; Belay, Tariku; Mekonnen, Seleshi Kebede; Zeynudin, Ahmed; Belachew, Tefera

2017-01-01

Introduction Soil transmitted helminths are wide spread in developing countries and in Ethiopia the prevalence of STHs varies in different parts of the country. The aim of this study was to determine the prevalence and intensity of soil transmitted helminths among school children of Mendera Elementary School Jimma town, Southwestern Ethiopia. Methods A cross-sectional study was conducted between March 29 and April 9, 2010 to determine the prevalence and intensity of soil transmitted helminths among elementary school children. The study participants were randomly selected from class enrollment list after proportional allocation of the total sample size to each grade. Data about the background characteristics were collected using structured questionnaire. The stool samples were examined by McMaster method for the egg count which was used to determine intensity of infection. Data were analyzed using SPSS for windows version 16 and p-value less than 5% was considered as statistically significant. Results Of the total 715 stool specimens examined, 346 were positive for at least one intestinal parasite making the prevalence 48.4%. The most prevalent parasites were Ascaris lumbricoides 169 (23.6%) and Trichuris trichiura 165 (23.1%). The prevalence of soil transmitted helminth in this study was 45.6% (326/715). There was statistically significant difference in the prevalence of Trichuriasis between those who use latrine always and who use sometimes (p = 0.010). Females are two times more likely to be positive for Ascaris than males (p = 0.039). Majority of the students had light infection of soil transmitted helminths and none of them had heavy intensity of infection of Trichuriasis and hookworms. Conclusion Nearly half of the school children were infected with at least one STHs and majority of the students had light infection of soil transmitted helminths. Students who did not wash their hands after defecation were three times more likely to be positive for Ascaris infection than those who washed their hands after defecation. Therefore, measures like health information dissemination on the advantage of washing hands after defecation and on proper use of latrine should be taken into account to alleviate the problem. PMID:28819509

The influence of power and actor relations on priority setting and resource allocation practices at the hospital level in Kenya: a case study.

PubMed

Barasa, Edwine W; Cleary, Susan; English, Mike; Molyneux, Sassy

2016-09-30

Priority setting and resource allocation in healthcare organizations often involves the balancing of competing interests and values in the context of hierarchical and politically complex settings with multiple interacting actor relationships. Despite this, few studies have examined the influence of actor and power dynamics on priority setting practices in healthcare organizations. This paper examines the influence of power relations among different actors on the implementation of priority setting and resource allocation processes in public hospitals in Kenya. We used a qualitative case study approach to examine priority setting and resource allocation practices in two public hospitals in coastal Kenya. We collected data by a combination of in-depth interviews of national level policy makers, hospital managers, and frontline practitioners in the case study hospitals (n = 72), review of documents such as hospital plans and budgets, minutes of meetings and accounting records, and non-participant observations in case study hospitals over a period of 7 months. We applied a combination of two frameworks, Norman Long's actor interface analysis and VeneKlasen and Miller's expressions of power framework to examine and interpret our findings RESULTS: The interactions of actors in the case study hospitals resulted in socially constructed interfaces between: 1) senior managers and middle level managers 2) non-clinical managers and clinicians, and 3) hospital managers and the community. Power imbalances resulted in the exclusion of middle level managers (in one of the hospitals) and clinicians and the community (in both hospitals) from decision making processes. This resulted in, amongst others, perceptions of unfairness, and reduced motivation in hospital staff. It also puts to question the legitimacy of priority setting processes in these hospitals. Designing hospital decision making structures to strengthen participation and inclusion of relevant stakeholders could improve priority setting practices. This should however, be accompanied by measures to empower stakeholders to contribute to decision making. Strengthening soft leadership skills of hospital managers could also contribute to managing the power dynamics among actors in hospital priority setting processes.

Thermal and vibration testing of ruggedized IR-transmitting fiber cables

NASA Astrophysics Data System (ADS)

Busse, Lynda; Kung, Fred; Florea, Catalin; Shaw, Brandon; Aggarwal, Ishwar; Sanghera, Jas

2013-05-01

We present successful results obtained for thermal/ vibration testing of ruggedized, IR-transmitting chalcogenide glass fiber cables using a government facility with state-of-the-art equipment capable of MIL-SPEC environmental testing. We will also present results of a direct imprinting process to create novel "moth eye" patterned surfaces on the IR fiber cable ends that significantly reduces endface reflection losses from 17% to less than 3%. The cables with these imprinted "moth eye" ends transmit much higher IR laser power without damage than was obtained for previous cables with traditional AR coatings.

Design considerations for remotely piloted, high-altitude airplanes powered by microwave energy

NASA Technical Reports Server (NTRS)

Morris, C. E. K., Jr.

1984-01-01

Several types of systems have been considered in a design study of unmanned, microwave-powered, long-endurance, high-altitude airplanes. The study includes vehicles that use power from a continuously transmitted beam and other aircraft that receive intermittent power during cycles of boost-glide flight. Simple design algorithms are presented. Examples of sizing and performance analyses are used to suggest design-procedure guidelines.

AC HTS Transmission Cable for Integration into the Future EHV Grid of the Netherlands

NASA Astrophysics Data System (ADS)

Zuijderduin, R.; Chevtchenko, O.; Smit, J. J.; Aanhaanen, G.; Melnik, I.; Geschiere, A.

Due to increasing power demand, the electricity grid of the Netherlands is changing. The future grid must be capable to transmit all the connected power. Power generation will be more decentralized like for instance wind parks connected to the grid. Furthermore, future large scale production units are expected to be installed near coastal regions. This creates some potential grid issues, such as: large power amounts to be transmitted to consumers from west to east and grid stability. High temperature superconductors (HTS) can help solving these grid problems. Advantages to integrate HTS components at Extra High Voltage (EHV) and High Voltage (HV) levels are numerous: more power with less losses and less emissions, intrinsic fault current limiting capability, better control of power flow, reduced footprint, etc. Today's main obstacle is the relatively high price of HTS. Nevertheless, as the price goes down, initial market penetration for several HTS components is expected by year 2015 (e.g.: cables, fault current limiters). In this paper we present a design of intrinsically compensated EHV HTS cable for future grid integration. Discussed are the parameters of such cable providing an optimal power transmission in the future network.

Power Allocation Based on Data Classification in Wireless Sensor Networks

PubMed Central

Wang, Houlian; Zhou, Gongbo

2017-01-01

Limited node energy in wireless sensor networks is a crucial factor which affects the monitoring of equipment operation and working conditions in coal mines. In addition, due to heterogeneous nodes and different data acquisition rates, the number of arriving packets in a queue network can differ, which may lead to some queue lengths reaching the maximum value earlier compared with others. In order to tackle these two problems, an optimal power allocation strategy based on classified data is proposed in this paper. Arriving data is classified into dissimilar classes depending on the number of arriving packets. The problem is formulated as a Lyapunov drift optimization with the objective of minimizing the weight sum of average power consumption and average data class. As a result, a suboptimal distributed algorithm without any knowledge of system statistics is presented. The simulations, conducted in the perfect channel state information (CSI) case and the imperfect CSI case, reveal that the utility can be pushed arbitrarily close to optimal by increasing the parameter V, but with a corresponding growth in the average delay, and that other tunable parameters W and the classification method in the interior of utility function can trade power optimality for increased average data class. The above results show that data in a high class has priorities to be processed than data in a low class, and energy consumption can be minimized in this resource allocation strategy. PMID:28498346

Handover Control Method Using Resource Reservation in Mobile Multimedia Networks

NASA Astrophysics Data System (ADS)

Lee, Dong Chun; Lee, Jong Chan

When handover events occur during the transmission of multimedia traffic, efficient handover control procedures and radio resource allocation are necessary to maintain the same QoS of transmitted multimedia traffic because the QoS may be degraded by additional delay and information loss. In this paper we propose a new handover control method for the next generation mobile multimedia networks, in which the handover setup process is done in advance of a handover request by predicting the handover cell from mobile terminal's current position. The handover procedures for real-time sessions are performed based on the handover cell information and the resource reservation condition. The radio resources in the estimated adjacent cells should be reserved and allocated to guarantee the continuity of the real-time sessions. We conduct a simulation model that is focused on the handover failure rate and packet loss rate. The simulation results show that our proposed method provides better performance than the previous methods.

Variable disparity estimation based intermediate view reconstruction in dynamic flow allocation over EPON-based access networks

NASA Astrophysics Data System (ADS)

Bae, Kyung-Hoon; Lee, Jungjoon; Kim, Eun-Soo

2008-06-01

In this paper, a variable disparity estimation (VDE)-based intermediate view reconstruction (IVR) in dynamic flow allocation (DFA) over an Ethernet passive optical network (EPON)-based access network is proposed. In the proposed system, the stereoscopic images are estimated by a variable block-matching algorithm (VBMA), and they are transmitted to the receiver through DFA over EPON. This scheme improves a priority-based access network by converting it to a flow-based access network with a new access mechanism and scheduling algorithm, and then 16-view images are synthesized by the IVR using VDE. Some experimental results indicate that the proposed system improves the peak-signal-to-noise ratio (PSNR) to as high as 4.86 dB and reduces the processing time to 3.52 s. Additionally, the network service provider can provide upper limits of transmission delays by the flow. The modeling and simulation results, including mathematical analyses, from this scheme are also provided.

10 CFR 205.303 - Required exhibits.

Code of Federal Regulations, 2010 CFR

2010-01-01

... DEPARTMENT OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System Permits and Reports; Applications; Administrative Procedures and Sanctions Application for Authorization to Transmit Electric Energy... within the corporate power of the applicant, and that the applicant has complied or will comply with all...

Parametric study of intersatellite CO2 laser data links

NASA Astrophysics Data System (ADS)

Bonek, E.; Lutz, H.

The performance capability of current CO2 laser communication tecnology for intersatellite data links is evaluated. The link parameters, such as the distance, bit rate, ac signal-to-noise ratio, are related to the masses and the prime power requirements of satellite laser terminals using variables like the telescope (antenna) aperture diameter and the transmitted laser power. It is found that high data rates could be readily transmitted with telescopes of the order of only 10 cm in diameter, with the complte laser data terminals weighing between 25 kg and 70 kg and consuming prime power in the 90-300 W range. In addition, these terminals would require only about 0.1 cu m or less of volume and a very low movable antenna mass, which would alleviate constraints on satellite attitude control units in remote sensing missions.

Combined Effect of Random Transmit Power Control and Inter-Path Interference Cancellation on DS-CDMA Packet Mobile Communications

NASA Astrophysics Data System (ADS)

Kudoh, Eisuke; Ito, Haruki; Wang, Zhisen; Adachi, Fumiyuki

In mobile communication systems, high speed packet data services are demanded. In the high speed data transmission, throughput degrades severely due to severe inter-path interference (IPI). Recently, we proposed a random transmit power control (TPC) to increase the uplink throughput of DS-CDMA packet mobile communications. In this paper, we apply IPI cancellation in addition to the random TPC. We derive the numerical expression of the received signal-to-interference plus noise power ratio (SINR) and introduce IPI cancellation factor. We also derive the numerical expression of system throughput when IPI is cancelled ideally to compare with the Monte Carlo numerically evaluated system throughput. Then we evaluate, by Monte-Carlo numerical computation method, the combined effect of random TPC and IPI cancellation on the uplink throughput of DS-CDMA packet mobile communications.

47 CFR 73.310 - FM technical definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... transmits the horizontal component of radiation. Antenna power gain. The square of the ratio of the root... millivolts per meter for 1 kW antenna input power to 221.4 mV/m. This ratio is expressed in decibels (dB). If specified for a particular direction, antenna power gain is based on that field strength in the direction...

47 CFR 73.310 - FM technical definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... transmits the horizontal component of radiation. Antenna power gain. The square of the ratio of the root... millivolts per meter for 1 kW antenna input power to 221.4 mV/m. This ratio is expressed in decibels (dB). If specified for a particular direction, antenna power gain is based on that field strength in the direction...

47 CFR 73.310 - FM technical definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... transmits the horizontal component of radiation. Antenna power gain. The square of the ratio of the root... millivolts per meter for 1 kW antenna input power to 221.4 mV/m. This ratio is expressed in decibels (dB). If specified for a particular direction, antenna power gain is based on that field strength in the direction...

47 CFR 73.310 - FM technical definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... transmits the horizontal component of radiation. Antenna power gain. The square of the ratio of the root... millivolts per meter for 1 kW antenna input power to 221.4 mV/m. This ratio is expressed in decibels (dB). If specified for a particular direction, antenna power gain is based on that field strength in the direction...

A High-Performance Portable Transient Electro-Magnetic Sensor for Unexploded Ordnance Detection.

PubMed

Wang, Haofeng; Chen, Shudong; Zhang, Shuang; Yuan, Zhiwen; Zhang, Haiyang; Fang, Dong; Zhu, Jun

2017-11-17

Portable transient electromagnetic (TEM) systems can be well adapted to various terrains, including mountainous, woodland, and other complex terrains. They are widely used for the detection of unexploded ordnance (UXO). As the core component of the portable TEM system, the sensor is constructed with a transmitting coil and a receiving coil. Based on the primary field of the transmitting coil and internal noise of the receiving coil, the design and testing of such a sensor is described in detail. Results indicate that the primary field of the transmitting coil depends on the diameter, mass, and power of the coil. A higher mass-power product and a larger diameter causes a stronger primary field. Reducing the number of turns and increasing the clamp voltage reduces the switch-off time of the transmitting current effectively. Increasing the cross-section of the wire reduces the power consumption, but greatly increases the coil's weight. The study of the receiving coil shows that the internal noise of the sensor is dominated by the thermal noise of the damping resistor. Reducing the bandwidth of the system and increasing the size of the coil reduces the internal noise effectively. The cross-sectional area and the distance between the sections of the coil have little effect on the internal noise. A less damped state can effectively reduce signal distortion. Finally, a portable TEM sensor with both a transmitting coil (constructed with a diameter, number of turns, and transmitting current of 0.5 m, 30, and 5 A, respectively) and a receiving coil (constructed with a length and resonant frequency of 5.6 cm and 50 kHz, respectively) was built. The agreement between experimental and calculated results confirms the theory used in the sensor design. The responses of an 82 mm mortar shell at different distances were measured and inverted by the differential evolution (DE) algorithm to verify system performance. Results show that the sensor designed in this study can not only detect the 82 mm mortar shell within 1.2 m effectively but also locate the target precisely.

ASPEC: Solar power satellite

NASA Technical Reports Server (NTRS)

1991-01-01

The solar power satellite (SPS) will provide a clean, reliable source of energy for large-scale consumption. The system will use satellites in geostationary orbits around the Earth to capture the Sun's energy. The intercepted sunlight will be converted to laser beam energy that can be transmitted to the Earth's surface. Ground systems on the Earth will convert the transmissions from space into electric power. The preliminary design for the SPS consists of one satellite in orbit around the Earth transmitting energy to a single ground station. The SPS design uses multilayer solar cell technology arranged on a 20 km squared planar array to intercept sunlight and convert it to an electric voltage. Power conditioning devices then send the electricity to a laser, which transmits the power to the surface of the Earth. A ground station will convert the beam into electricity. Typically, a single SPS will supply 5 GW of power to the ground station. Due to the large mass of the SPS, about 41 million kg, construction in space is needed in order to keep the structural mass low. The orbit configuration for this design is to operate a single satellite in geosynchronous orbit (GEO). The GEO allows the system to be positioned above a single receiving station and remain in sunlight 99 percent of the time. Construction will take place in low Earth orbit (LEO); array sections, 20 in total, will be sailed on solar wind out to the GEO location in 150 days. These individual transportation sections are referred to as solar sailing array panels (SSAP's). The primary truss elements used to support the array are composed of composite tubular members in a pentahedral arrangement. Smart segments consisting of passive and active damping devices will increase the control of dynamic SPS modes.

AIDS in Africa.

PubMed

Mokhobo, D

1989-03-01

Numerous cultural practices and attitudes in Africa represent formidable obstacles to the prevention of the further spread of acquired immunodeficiency syndrome (AIDS). Polygamy and concubinage are still widely practiced throughout Africa. In fact, sexual promiscuity on the part of males is traditionally viewed as positive--a reflection of male supremacy and male sexual prowess. The disintegration of the rural African family, brought about by urbanization, the migrant labor system, and poverty, has resulted in widespread premarital promiscuity. Contraceptive practices are perceived by many as a white conspiracy aimed at limiting the growth of the black population and thereby diminishing its political power. Condom use is particularly in disfavor. Thus, AIDS prevention campaigns urging Africans to restrict the number of sexual partners and to use condoms are unlikely to be successful. Another problem is that most Africans cannot believe that AIDS is sexually linked in that the disease does not affect the sex organs as is the case with other sexually transmitted diseases. The degree to which African governments are able to allocate resources to AIDS education will determine whether the epidemic can be controlled. Even with a massive outpouring of resources, it may be difficult to arouse public alarm about AIDS since Africans are so acclimated to living with calamities of every kind.

A balloon-borne experiment to investigate the Martian magnetic field

NASA Astrophysics Data System (ADS)

Schwingenschuh, K.; Feldhofer, H.; Koren, W.; Jernej, I.; Stachel, M.; Riedler, W.; Slamanig, H.; Auster, H.-U.; Rustenbach, J.; Fornacon, H. K.; Schenk, H. J.; Hillenmaier, O.; Haerendel, G.; Yeroshenko, Ye.; Styashkin, V.; Zaroutzky, A.; Best, A.; Scholz, G.; Russell, C. T.; Means, J.; Pierce, D.; Luhmann, J. G.

1996-03-01

The Space Research Institute of the Austrian Academy, of Sciences (Graz, Austria) in cooperation with MPE (Berlin, Germany), GFZ Potsdam (Obs. Niemegk, Germany) IZMIRAN/IOFAN (Moscow, Russian) and IGPP/UCLA (Los Angeles, USA) is designing the magnetic field experiment MAGIBAL (MAGnetic field experiment aboard a martian BALloon) to investigate the magnetic field on the surface of Mars. The dual sensor fluxgate magnetometer is part of the MARS-98/MARS-TOGETHER balloon payload. During a ten days period the balloon will float over a distance of about 2000 km at altitudes between 0 and 4 km. Due to the limited power and telemetry allocation the magnetometer can transmit only one vector per ten seconds and spectral information in the frequency range from 2 - 25 Hz. The dynamic range is +/- 2000 nT. The main scientific objectives of the experiment are: • Determination of the magnetism of the Martian rocks • Investigation of the leakage of the solar wind induced magnetosphere using the correlation between orbiter and balloon observations • Measurement of the magnetic field profile between the orbiter and the surface of Mars during the descent phase of the balloon. Terrestrial test flights with a hot air balloon were performed in order to test the original MAGIBAL equipment under balloon flight conditions.

Hybrid digital-analog coding with bandwidth expansion for correlated Gaussian sources under Rayleigh fading

NASA Astrophysics Data System (ADS)

Yahampath, Pradeepa

2017-12-01

Consider communicating a correlated Gaussian source over a Rayleigh fading channel with no knowledge of the channel signal-to-noise ratio (CSNR) at the transmitter. In this case, a digital system cannot be optimal for a range of CSNRs. Analog transmission however is optimal at all CSNRs, if the source and channel are memoryless and bandwidth matched. This paper presents new hybrid digital-analog (HDA) systems for sources with memory and channels with bandwidth expansion, which outperform both digital-only and analog-only systems over a wide range of CSNRs. The digital part is either a predictive quantizer or a transform code, used to achieve a coding gain. Analog part uses linear encoding to transmit the quantization error which improves the performance under CSNR variations. The hybrid encoder is optimized to achieve the minimum AMMSE (average minimum mean square error) over the CSNR distribution. To this end, analytical expressions are derived for the AMMSE of asymptotically optimal systems. It is shown that the outage CSNR of the channel code and the analog-digital power allocation must be jointly optimized to achieve the minimum AMMSE. In the case of HDA predictive quantization, a simple algorithm is presented to solve the optimization problem. Experimental results are presented for both Gauss-Markov sources and speech signals.

Wideband Communications Equipment, Ground Radio Communication, Space Comm Systems Equipment. 304X0/X4/X6. Appendix A - Task Analysis

DTIC Science & Technology

1990-05-01

ALARM LAMPS A CHECK TWT POWER SUPPLY VOLTAGE AND CURRENT A ADJUST POWER ALARM THRESHOLD AND TRANSMITTER OUTPUT A CHECK HELIX MONITOR K INTERPRET AN/FRC...POWER SUPPLY A CHECK TRAVELING WAVE TUBE ( TWT ) POWER SUPPLY HELIX CURRENT AND BEAM CURRENT A CHECK TWT RF POWER OUTPUT A CHECK TRANSMITTER POWER...A ADJUST TRANSMITTER LINEARITY A CALIBRATE TRANSMIT DEVIATION AND ADJUST MODULATION AMPLIFIER A ADJUST TWT PERFORMANCE MONITOR A ADJUST TWT OUTPUT

47 CFR 95.669 - External controls.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Audio frequency power amplifier output connector and selector switch. (5) On-off switch for primary power to transmitter. This switch may be combined with receiver controls such as the receiver on-off switch and volume control. (6) Upper/lower sideband selector switch (for a transmitter that transmits...

47 CFR 74.783 - Station identification.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES Low Power TV, TV Translator, and TV Booster Stations § 74.783 Station identification. (a) Each low power TV and TV translator station not..., whose signal is being rebroadcast, to identify the translator station by transmitting an easily readable...

Hollow fiber optics with improved durability for high-peak-power pulses of Q-switched Nd:YAG lasers.

PubMed

Matsuura, Yuji; Tsuchiuchi, Akio; Noguchi, Hiroshi; Miyagi, Mitsunobu

2007-03-10

To improve the damage threshold of hollow optical waveguides for transmitting Q-switched Nd:YAG laser pulses, we optimize the metallization processes for the inner coating of fibers. For silver-coated hollow fiber as the base, second, and third Nd:YAG lasers, drying silver films at a moderate temperature and with inert gas flow is found to be effective. By using this drying process, the resistance to high-peak-power optical pulse radiation is drastically improved for fibers fabricated with and without the sensitizing process. The maximum peak power transmitted in the fiber is greater than 20 MW. To improve the energy threshold of aluminum-coated hollow fibers for the fourth and fifth harmonics of Nd:YAG lasers, a thin silver film is added between the aluminum film and the glass substrate to increase adhesion of the aluminum coating. By using this primer layer, the power threshold improves to 3 MW for the fourth harmonics of a Q-switched Nd:YAG laser light.

Design of a telemetry system based on wireless power transmission for physiological parameter monitoring

NASA Astrophysics Data System (ADS)

Jia, Zhiwei; Yan, Guozheng; Zhu, Bingquan

2015-04-01

An implanted telemetry system for experimental animals with or without anaesthesia can be used to continuously monitor physiological parameters. This system is significant not only in the study of organisms but also in the evaluation of drug efficacy, artificial organs, and auxiliary devices. The system is composed of a miniature electronic capsule, a wireless power transmission module, a data-recording device, and a processing module. An electrocardiograph, a temperature sensor, and a pressure sensor are integrated in the miniature electronic capsule, in which the signals are transmitted in vitro by wireless communication after filtering, amplification, and A/D sampling. To overcome the power shortage of batteries, a wireless power transmission module based on electromagnetic induction was designed. The transmitting coil of a rectangular-section solenoid and a 3D receiving coil are proposed according to stability and safety constraints. Experiments show that at least 150 mW of power could pick up on the load in a volume of Φ10.5 mm × 11 mm, with a transmission efficiency of 2.56%. Vivisection experiments verified the feasibility of the integrated radio-telemetry system.

Pulse homodyne field disturbance sensor

DOEpatents

McEwan, Thomas E.

1997-01-01

A field disturbance sensor operates with relatively low power, provides an adjustable operating range, is not hypersensitive at close range, allows co-location of multiple sensors, and is inexpensive to manufacture. The sensor includes a transmitter that transmits a sequence of transmitted bursts of electromagnetic energy. The transmitter frequency is modulated at an intermediate frequency. The sequence of bursts has a burst repetition rate, and each burst has a burst width and comprises a number of cycles at a transmitter frequency. The sensor includes a receiver which receives electromagnetic energy at the transmitter frequency, and includes a mixer which mixes a transmitted burst with reflections of the same transmitted burst to produce an intermediate frequency signal. Circuitry, responsive to the intermediate frequency signal indicates disturbances in the sensor field. Because the mixer mixes the transmitted burst with reflections of the transmitted burst, the burst width defines the sensor range. The burst repetition rate is randomly or pseudo-randomly modulated so that bursts in the sequence of bursts have a phase which varies. A second range-defining mode transmits two radio frequency bursts, where the time spacing between the bursts defines the maximum range divided by two.

Pulse homodyne field disturbance sensor

DOEpatents

McEwan, T.E.

1997-10-28

A field disturbance sensor operates with relatively low power, provides an adjustable operating range, is not hypersensitive at close range, allows co-location of multiple sensors, and is inexpensive to manufacture. The sensor includes a transmitter that transmits a sequence of transmitted bursts of electromagnetic energy. The transmitter frequency is modulated at an intermediate frequency. The sequence of bursts has a burst repetition rate, and each burst has a burst width and comprises a number of cycles at a transmitter frequency. The sensor includes a receiver which receives electromagnetic energy at the transmitter frequency, and includes a mixer which mixes a transmitted burst with reflections of the same transmitted burst to produce an intermediate frequency signal. Circuitry, responsive to the intermediate frequency signal indicates disturbances in the sensor field. Because the mixer mixes the transmitted burst with reflections of the transmitted burst, the burst width defines the sensor range. The burst repetition rate is randomly or pseudo-randomly modulated so that bursts in the sequence of bursts have a phase which varies. A second range-defining mode transmits two radio frequency bursts, where the time spacing between the bursts defines the maximum range divided by two. 12 figs.

Symmetric reconfigurable capacity assignment in a bidirectional DWDM access network.

PubMed

Ortega, Beatriz; Mora, José; Puerto, Gustavo; Capmany, José

2007-12-10

This paper presents a novel architecture for DWDM bidirectional access networks providing symmetric dynamic capacity allocation for both downlink and uplink signals. A foldback arrayed waveguide grating incorporating an optical switch enables the experimental demonstration of flexible assignment of multiservice capacity. Different analog and digital services, such as CATV, 10 GHz-tone, 155Mb/s PRBS and UMTS signals have been transmitted in order to successfully test the system performance under different scenarios of total capacity distribution from the Central Station to different Base Stations with two reconfigurable extra channels for each down and upstream direction.

Sexual networks in contemporary Western societies

NASA Astrophysics Data System (ADS)

Liljeros, Fredrik

2004-07-01

Sexually transmitted infections continue to be a severe health problem in contemporary Western societies, despite the considerable funds allocated for control programs. In this article, we present and discuss a variety of explanations that have been advanced on why this type of disease is so hard to eradicate, despite the fact that the contact by which it is spread is far less frequent than is the case with most other infectious diseases. We conclude that several processes and mechanisms facilitate the spread of sexually infected diseases, and that both broad and targeted intervention is therefore needed to eradicate such diseases.

Development of 20 GHz monolithic transmit modules

NASA Technical Reports Server (NTRS)

Higgins, J. A.

1988-01-01

The history of the development of a transmit module for the band 17.7 to 20.2 GHz is presented. The module was to monolithically combine, on one chip, five bits of phase shift, a buffer amplifier and a power amplifier to produce 200 mW to the antenna element. The approach taken was MESFET ion implanted device technology. A common pinch-off voltage was decided upon for each application. The beginning of the total integration phases revealed hitherto unencountered hazards of large microwave circuit integration which were successfully overcome. Yield and customer considerations finally led to two separate chips, one containing the power amplifiers and the other containing the complete five bit phase shifter.

Using Piezoelectric Devices to Transmit Power through Walls

NASA Technical Reports Server (NTRS)

Sherrit, Stewart; Bar-Cohen, Yoseph; Bao, Xiaoqi

2008-01-01

A method denoted wireless acoustic-electric feed-through (WAEF) has been conceived for transmitting power and/or data signals through walls or other solid objects made of a variety of elastic materials that could be electrically conductive or nonconductive. WAEF would make it unnecessary to use wires, optical fibers, tubes, or other discrete wall-penetrating signal-transmitting components, thereby eliminating the potential for structural weakening or leakage at such penetrations. Avoidance of such penetrations could be essential in some applications in which maintenance of pressure, vacuum, or chemical or biological isolation is required. In a basic WAEF setup, a transmitting piezoelectric transducer on one side of a wall would be driven at resonance to excite ultrasonic vibrations in the wall. A receiving piezoelectric transducer on the opposite side of the wall would convert the vibrations back to an ultrasonic AC electric signal, which would then be detected and otherwise processed in a manner that would depend on the modulation (if any) applied to the signal and whether the signal was used to transmit power, data, or both. An electromechanical-network model has been derived as a computationally efficient means of analyzing and designing a WAEF system. This model is a variant of a prior model, known in the piezoelectric-transducer art as Mason's equivalent-circuit model, in which the electrical and mechanical dynamics, including electromechanical couplings, are expressed as electrical circuit elements that can include inductors, capacitors, and lumped-parameter complex impedances. The real parts of the complex impedances are used to account for dielectric, mechanical, and coupling losses in all components (including all piezoelectric-transducer, wall, and intermediate material layers). In an application to a three-layer piezoelectric structure, this model was shown to yield the same results as do solutions of the wave equations of piezoelectricity and acoustic propagation in their full complexity.

DEB Type I Reconstitution Package Deployment Manual (RPDM).

DTIC Science & Technology

1981-05-01

Waveguide Assembly (d) 1177H02 TWT Power Amplifier (e) TCM-6RK-I Transmit and Receive Remote Kits 20 C" I--I- CL* Figure 8. Terminal 21 17 February...Twist Six Waveguide to Coax Adapters 1.2.1.1.1(d) TWT Power Amplifier. The power amplifier utilizes a periodic permanent magnetic focused travelling...possible to adjust input power while observing TWT output with a power meter and directional coupler. The capability of controlling the TWT drive

Photovoltaic receivers for laser beamed power in space

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.

1991-01-01

There has recently been a resurgence of interest in the use of beamed power to support space exploration activities. One of the most promising beamed power concepts uses a laser beam to transmit power to a remote photovoltaic array. Large lasers can be located on cloud-free sites at one or more ground locations and illuminate solar arrays to a level sufficient to provide operating power. Issues involved in providing photovoltaic receivers for such applications are discussed.

47 CFR 2.815 - External radio frequency power amplifiers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false External radio frequency power amplifiers. 2.815 Section 2.815 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2.815...

47 CFR 2.815 - External radio frequency power amplifiers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false External radio frequency power amplifiers. 2.815 Section 2.815 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2.815...

Microwave Driven Actuators Power Allocation and Distribution

NASA Technical Reports Server (NTRS)

Forbes, Timothy; Song, Kyo D.

2000-01-01

Design, fabrication and test of a power allocation and distribution (PAD) network for microwave driven actuators is presented in this paper. Development of a circuit that would collect power from a rectenna array amplify and distribute the power to actuators was designed and fabricated for space application in an actuator array driven by a microwave. A P-SPICE model was constructed initially for data reduction purposes, and was followed by a working real-world model. A voltage up - converter (VUC) is used to amplify the voltage from the individual rectenna. The testing yielded a 26:1 voltage amplification ratio with input voltage at 9 volts and a measured output voltage 230VDC. Future work includes the miniaturization of the circuitry, the use of microwave remote control, and voltage amplification technology for each voltage source. The objective of this work is to develop a model system that will collect DC voltage from an array of rectenna and propagate the voltage to an array of actuators.

Re-insurance in the Swiss health insurance market: Fit, power, and balance.

PubMed

Schmid, Christian P R; Beck, Konstantin

2016-07-01

Risk equalization mechanisms mitigate insurers' incentives to practice risk selection. On the other hand, incentives to limit healthcare spending can be distorted by risk equalization, particularly when risk equalization payments depend on realized costs instead of expected costs. In addition, cost based risk equalization mechanisms may incentivize health insurers to distort the allocation of resources among different services. The incentives to practice risk selection, to limit healthcare spending, and to distort the allocation of resources can be measured by fit, power, and balance, respectively. We apply these three measures to evaluate the risk adjustment mechanism in Switzerland. Our results suggest that it performs very well in terms of power but rather poorly in terms of fit. The latter indicates that risk selection might be a severe problem. We show that re-insurance can reduce this problem while power remains on a high level. In addition, we provide evidence that the Swiss risk equalization mechanism does not lead to imbalances across different services. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

47 CFR 25.212 - Narrowband analog transmissions and digital transmissions in the GSO Fixed Satellite Service.

Code of Federal Regulations, 2014 CFR

2014-10-01

... kHz (or up to 1 MHz for command carriers at the band edge) if the equivalent diameter of the... dBW/4 kHz, transmitted satellite carrier EIRP density will not exceed 17 dBW/4 kHz, and the... greater, input power spectral density into the antenna will not exceed −14 dBW/4 kHz, transmitted...

Constant-current control method of multi-function electromagnetic transmitter.

PubMed

Xue, Kaichang; Zhou, Fengdao; Wang, Shuang; Lin, Jun

2015-02-01

Based on the requirements of controlled source audio-frequency magnetotelluric, DC resistivity, and induced polarization, a constant-current control method is proposed. Using the required current waveforms in prospecting as a standard, the causes of current waveform distortion and current waveform distortion's effects on prospecting are analyzed. A cascaded topology is adopted to achieve 40 kW constant-current transmitter. The responsive speed and precision are analyzed. According to the power circuit of the transmitting system, the circuit structure of the pulse width modulation (PWM) constant-current controller is designed. After establishing the power circuit model of the transmitting system and the PWM constant-current controller model, analyzing the influence of ripple current, and designing an open-loop transfer function according to the amplitude-frequency characteristic curves, the parameters of the PWM constant-current controller are determined. The open-loop transfer function indicates that the loop gain is no less than 28 dB below 160 Hz, which assures the responsive speed of the transmitting system; the phase margin is 45°, which assures the stabilization of the transmitting system. Experimental results verify that the proposed constant-current control method can keep the control error below 4% and can effectively suppress load change caused by the capacitance of earth load.

Constant-current control method of multi-function electromagnetic transmitter

NASA Astrophysics Data System (ADS)

Xue, Kaichang; Zhou, Fengdao; Wang, Shuang; Lin, Jun

2015-02-01

Based on the requirements of controlled source audio-frequency magnetotelluric, DC resistivity, and induced polarization, a constant-current control method is proposed. Using the required current waveforms in prospecting as a standard, the causes of current waveform distortion and current waveform distortion's effects on prospecting are analyzed. A cascaded topology is adopted to achieve 40 kW constant-current transmitter. The responsive speed and precision are analyzed. According to the power circuit of the transmitting system, the circuit structure of the pulse width modulation (PWM) constant-current controller is designed. After establishing the power circuit model of the transmitting system and the PWM constant-current controller model, analyzing the influence of ripple current, and designing an open-loop transfer function according to the amplitude-frequency characteristic curves, the parameters of the PWM constant-current controller are determined. The open-loop transfer function indicates that the loop gain is no less than 28 dB below 160 Hz, which assures the responsive speed of the transmitting system; the phase margin is 45°, which assures the stabilization of the transmitting system. Experimental results verify that the proposed constant-current control method can keep the control error below 4% and can effectively suppress load change caused by the capacitance of earth load.

A novel optical millimeter-wave signal generation approach to overcome chromatic dispersion

NASA Astrophysics Data System (ADS)

Liang, Dong; Jiang, Wei; Tan, Qinggui; Zhu, Zhongbo; Liu, Feng

2014-06-01

In this paper, a novel frequency octupling approach for optical millimeter-wave signal generation to overcome chromatic dispersion is proposed and demonstrated. The frequency octupling mm-wave with the baseband signal carried only by -4th order sideband is generated by properly adjusting a series of parameters, which are the modulation constant, the gain of baseband signal, the direct current bias and the different phase of the modulation arms. As the optical millimeter-wave signal is transmitted along the fiber, there is no time shift caused by chromatic dispersion. Theoretical analyses and simulated results show that when the optical mm-wave carrying 2.5 Gbps baseband signal transmits a distance of over 110 km, the eye diagram still keeps open and clear. The power penalty is about 0.4 dB after the optical signal transmits over 40 km. In additions, given the +4th order sideband carries no data, a full-duplex RoF link based on wavelength reuse is built for the uplink. The bidirectional 2.5 Gbps baseband signal could successfully transmit over 40 km with about 0.8 dB power penalty in the simulation. Both theoretical analyses and simulation results show that the full-duplex RoF link has good performance.

"Printed-circuit" rectenna

NASA Technical Reports Server (NTRS)

Dickinson, R. M.

1977-01-01

Rectifying antenna is less bulky structure for absorbing transmitted microwave power and converting it into electrical current. Printed-circuit approach, using microstrip technology and circularly polarized antenna, makes polarization orientation unimportant and allows much smaller arrays for given performance. Innovation is particularly useful with proposed electric vehicles powered by beam microwaves.

77 FR 24646 - Open Access and Priority Rights on Interconnection Facilities

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-25

... multiple generation facilities to transmit power from the generation facility to the integrated... power flows toward the network grid, with no electrical loads between the generation facilities and the... generator expansion plans with milestones for construction of generation facilities and can demonstrate that...

47 CFR 95.607 - CB transmitter modification.

Code of Federal Regulations, 2010 CFR

2010-10-01

... transmitting frequencies, increased modulation level, a different form of modulation, or increased TP (RF... modulating frequency, typically 0.1 seconds at maximum power) or peak envelope power (TP averaged during 1 RF cycle at the highest crest of the modulation envelope), as measured at the transmitter output antenna...

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Network. (r) Transmit Power Control (TPC). A feature that enables a U-NII device to dynamically switch... control level. Power must be summed across all antennas and antenna elements. The average must not include... modulation techniques and provide a wide array of high data rate mobile and fixed communications for...

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Network. (r) Transmit Power Control (TPC). A feature that enables a U-NII device to dynamically switch... control level. Power must be summed across all antennas and antenna elements. The average must not include... modulation techniques and provide a wide array of high data rate mobile and fixed communications for...

H2-O2 combustion powered steam-MHD central power systems

NASA Technical Reports Server (NTRS)

Seikel, G. R.; Smith, J. M.; Nichols, L. D.

1974-01-01

Estimates are made for both the performance and the power costs of H2-O2 combustion powered steam-MHD central power systems. Hydrogen gas is assumed to be transmitted by pipe from a remote coal gasifier into the city and converted to electricity in a steam MHD plant having an integral gaseous oxygen plant. These steam MHD systems appear to offer an attractive alternative to both in-city clean fueled conventional steam power plants and to remote coal fired power plants with underground electric transmission into the city.

Automated tuning of an eight-channel cardiac transceive array at 7 tesla using piezoelectric actuators.

PubMed

Keith, Graeme A; Rodgers, Christopher T; Hess, Aaron T; Snyder, Carl J; Vaughan, J Thomas; Robson, Matthew D

2015-06-01

Ultra-high field (UHF) MR scanning in the body requires novel coil designs due to B1 field inhomogeneities. In the transverse electromagnetic field (TEM) design, maximum B1 transmit power can only be achieved if each individual transmit element is tuned and matched for different coil loads, which requires a considerable amount of valuable scanner time. An integrated system for autotuning a multichannel parallel transmit (pTx) cardiac TEM array was devised, using piezoelectric actuators, power monitoring equipment and control software. The reproducibility and performance of the system were tested and the power responses of the coil elements were profiled. An automated optimization method was devised and evaluated. The time required to tune an eight-element pTx cardiac RF array was reduced from a mean of 30 min to less than 10 min with the use of this system. Piezoelectric actuators are an attractive means of tuning RF coil arrays to yield more efficient B1 transmission into the subject. An automated mechanism for tuning these elements provides a practical solution for cardiac imaging at UHF, bringing this technology closer to clinical use. © 2014 The Authors. Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine.

On-coil multiple channel transmit system based on class-D amplification and pre-amplification with current amplitude feedback

PubMed Central

Gudino, N.; Heilman, J.A; Riffe, M. J.; Heid, O.; Vester, M.; Griswold, M.A.

2016-01-01

A complete high-efficiency transmit amplifier unit designed to be implemented in on-coil transmit arrays is presented. High power capability, low power dissipation, scalability and cost minimization were some of the requirements imposed to the design. The system is composed of a current mode class-D (CMCD) amplifier output stage and a voltage mode class-D (VMCD) preamplification stage. The amplitude information of the radio frequency pulse was added through a customized step-down DC-DC converter with current amplitude feedback that connects to the CMCD stage. Benchtop measurements and imaging experiments were carried out to analyze system performance. Direct control of B1 was possible and its load sensitivity was reduced to less than 10% variation from unloaded to full loaded condition. When using the amplifiers in an array configuration, isolation above 20 dB was achieved between neighboring coils by the amplifier decoupling method. High output current operation of the transmitter was proved on the benchtop through output power measurements and in a 1.5 T scanner through flip angle quantification. Finally, single and multiple channel excitations with the new hardware were demonstrated by receiving signal with the body coil of the scanner. PMID:22890962

Energy-Efficient ZigBee-Based Wireless Sensor Network for Track Bicycle Performance Monitoring

PubMed Central

Gharghan, Sadik K.; Nordin, Rosdiadee; Ismail, Mahamod

2014-01-01

In a wireless sensor network (WSN), saving power is a vital requirement. In this paper, a simple point-to-point bike WSN was considered. The data of bike parameters, speed and cadence, were monitored and transmitted via a wireless communication based on the ZigBee protocol. Since the bike parameters are monitored and transmitted on every bike wheel rotation, this means the sensor node does not sleep for a long time, causing power consumption to rise. Therefore, a newly proposed algorithm, known as the Redundancy and Converged Data (RCD) algorithm, was implemented for this application to put the sensor node into sleep mode while maintaining the performance measurements. This is achieved by minimizing the data packets transmitted as much as possible and fusing the data of speed and cadence by utilizing the correlation measurements between them to minimize the number of sensor nodes in the network to one node, which results in reduced power consumption, cost, and size, in addition to simpler hardware implementation. Execution of the proposed RCD algorithm shows that this approach can reduce the current consumption to 1.69 mA, and save 95% of the sensor node energy. Also, the comparison results with different wireless standard technologies demonstrate minimal current consumption in the sensor node. PMID:25153141

On-coil multiple channel transmit system based on class-D amplification and pre-amplification with current amplitude feedback.

PubMed

Gudino, Natalia; Heilman, Jeremiah A; Riffe, Matthew J; Heid, Oliver; Vester, Markus; Griswold, Mark A

2013-07-01

A complete high-efficiency transmit amplifier unit designed to be implemented in on-coil transmit arrays is presented. High power capability, low power dissipation, scalability, and cost minimization were some of the requirements imposed to the design. The system is composed of a current mode class-D amplifier output stage and a voltage mode class-D preamplification stage. The amplitude information of the radio frequency pulse was added through a customized step-down DC-DC converter with current amplitude feedback that connects to the current mode class-D stage. Benchtop measurements and imaging experiments were carried out to analyze system performance. Direct control of B1 was possible and its load sensitivity was reduced to less than 10% variation from unloaded to full loaded condition. When using the amplifiers in an array configuration, isolation above 20 dB was achieved between neighboring coils by the amplifier decoupling method. High output current operation of the transmitter was proved on the benchtop through output power measurements and in a 1.5T scanner through flip angle quantification. Finally, single and multiple channel excitations with the new hardware were demonstrated by receiving signal with the body coil of the scanner. Copyright © 2012 Wiley Periodicals, Inc.

Colour-reproduction algorithm for transmitting variable video frames and its application to capsule endoscopy

PubMed Central

Khan, Tareq; Shrestha, Ravi; Imtiaz, Md. Shamin

2015-01-01

Presented is a new power-efficient colour generation algorithm for wireless capsule endoscopy (WCE) application. In WCE, transmitting colour image data from the human intestine through radio frequency (RF) consumes a huge amount of power. The conventional way is to transmit all R, G and B components of all frames. Using the proposed dictionary-based colour generation scheme, instead of sending all R, G and B frames, first one colour frame is sent followed by a series of grey-scale frames. At the receiver end, the colour information is extracted from the colour frame and then added to colourise the grey-scale frames. After a certain number of grey-scale frames, another colour frame is sent followed by the same number of grey-scale frames. This process is repeated until the end of the video sequence to maintain the colour similarity. As a result, over 50% of RF transmission power can be saved using the proposed scheme, which will eventually lead to a battery life extension of the capsule by 4–7 h. The reproduced colour images have been evaluated both statistically and subjectively by professional gastroenterologists. The algorithm is finally implemented using a WCE prototype and the performance is validated using an ex-vivo trial. PMID:26609405

Energy-efficient ZigBee-based wireless sensor network for track bicycle performance monitoring.

PubMed

Gharghan, Sadik K; Nordin, Rosdiadee; Ismail, Mahamod

2014-08-22

In a wireless sensor network (WSN), saving power is a vital requirement. In this paper, a simple point-to-point bike WSN was considered. The data of bike parameters, speed and cadence, were monitored and transmitted via a wireless communication based on the ZigBee protocol. Since the bike parameters are monitored and transmitted on every bike wheel rotation, this means the sensor node does not sleep for a long time, causing power consumption to rise. Therefore, a newly proposed algorithm, known as the Redundancy and Converged Data (RCD) algorithm, was implemented for this application to put the sensor node into sleep mode while maintaining the performance measurements. This is achieved by minimizing the data packets transmitted as much as possible and fusing the data of speed and cadence by utilizing the correlation measurements between them to minimize the number of sensor nodes in the network to one node, which results in reduced power consumption, cost, and size, in addition to simpler hardware implementation. Execution of the proposed RCD algorithm shows that this approach can reduce the current consumption to 1.69 mA, and save 95% of the sensor node energy. Also, the comparison results with different wireless standard technologies demonstrate minimal current consumption in the sensor node.

77 FR 55834 - Notice of Opportunity To Comment on a Methodology for Allocating Greenhouse Gas Emissions to a...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-11

... ethanol plant in Spiritwood, North Dakota, with a nameplate production capacity of 65 million gallons of... factor for the power plant when it is just generating electricity and not diverting steam to the Dakota... from the turbine, and applying the power plant's ``power only'' emissions factor to that value. The...

Nine wave-length THz spectrum for identification using backward wave oscillator

NASA Astrophysics Data System (ADS)

Lv, Mo; Zhong, Hua; Ge, Xin-hao; He, Ting; Mu, Kaijun; Zhang, Cun-lin

2009-11-01

The sensing of the explosive is very important for homeland security and defense. We present a nine-wavelength continuous wave (CW) Terahertz (THz) spectroscopy for identification of explosive compounds (2,4-DNT, RDX and TNT) using three Backward Wave Oscillator (BWO) sources, which emit radiations from 0.2 THz to 0.38THz, 0.18THz to 0.26THz and 0.6THz to 0.7THz, respectively. To identify the target materials, only the transmitted THz power through the explosive pellets are measured at the nine discrete wavelengths. A hole, which is the same size as these pellets, is used as references to normalize the transmitted THz power. The measured discrete spectra was successfully identified and classified by using self-organizing map (SOM). These results prove that the backward wave oscillator is a convenient and powerful solution in future development of a standoff THz sensing and identification unit.

Switchable in-line monitor for multi-dimensional multiplexed photonic integrated circuit.

PubMed

Chen, Guanyu; Yu, Yu; Ye, Mengyuan; Zhang, Xinliang

2016-06-27

A flexible monitor suitable for the discrimination of on-chip transmitted mode division multiplexed (MDM) and wavelength division multiplexed (WDM) signals is proposed and fabricated. By selectively extracting part of the incoming signals through the tunable wavelength and mode dependent drop filter, the in-line and switchable monitor can discriminate the wavelength, mode and power information of the transmitted signals. Being different from a conventional mode and wavelength demultiplexer, the monitor is specifically designed to ensure a flexible in-line monitoring. For demonstration, three mode and three wavelength multiplexed signals are successfully processed. Assisted by the integrated photodetectors (PDs), both the measured photo currents and eye diagrams validate the performance of the proposed device. The bit error ratio (BER) measurement results show less than 0.4 dB power penalty between different modes and ~2 dB power penalty for single wavelength and WDM cases under 10^-9 BER level.

Power selective optical filter devices and optical systems using same

DOEpatents

Koplow, Jeffrey P

2014-10-07

In an embodiment, a power selective optical filter device includes an input polarizer for selectively transmitting an input signal. The device includes a wave-plate structure positioned to receive the input signal, which includes at least one substantially zero-order, zero-wave plate. The zero-order, zero-wave plate is configured to alter a polarization state of the input signal passing in a manner that depends on the power of the input signal. The zero-order, zero-wave plate includes an entry and exit wave plate each having a fast axis, with the fast axes oriented substantially perpendicular to each other. Each entry wave plate is oriented relative to a transmission axis of the input polarizer at a respective angle. An output polarizer is positioned to receive a signal output from the wave-plate structure and selectively transmits the signal based on the polarization state.

On-Chip Power-Combining for High-Power Schottky Diode Based Frequency Multipliers

NASA Technical Reports Server (NTRS)

Siles Perez, Jose Vicente (Inventor); Chattopadhyay, Goutam (Inventor); Lee, Choonsup (Inventor); Schlecht, Erich T. (Inventor); Jung-Kubiak, Cecile D. (Inventor); Mehdi, Imran (Inventor)

2015-01-01

A novel MMIC on-chip power-combined frequency multiplier device and a method of fabricating the same, comprising two or more multiplying structures integrated on a single chip, wherein each of the integrated multiplying structures are electrically identical and each of the multiplying structures include one input antenna (E-probe) for receiving an input signal in the millimeter-wave, submillimeter-wave or terahertz frequency range inputted on the chip, a stripline based input matching network electrically connecting the input antennas to two or more Schottky diodes in a balanced configuration, two or more Schottky diodes that are used as nonlinear semiconductor devices to generate harmonics out of the input signal and produce the multiplied output signal, stripline based output matching networks for transmitting the output signal from the Schottky diodes to an output antenna, and an output antenna (E-probe) for transmitting the output signal off the chip into the output waveguide transmission line.

Intensity modulation of HF heater-induced plasma lines

NASA Technical Reports Server (NTRS)

Kuo, S. P.; Lee, M. C.

1990-01-01

The Arecibo HF heater is normally composed of two separate sets of antenna array, transmitting waves vertically at the same frequency and polarization. However, when these two sets of antenna array radiate at slightly different frequencies, the intensities of HF heater-induced plasma lines (HFPLs) can be drastically modulated. In recent Duncan et al.'s (1989) experiments the 100 percent intensity modulation of HFPLs was seen to persist even when the secondary set of antenna array radiated at a few percent of the power transmitted by the primary set of antenna array. An explanation is offered, and it is shown that there exists a minimum power, Pmin, and if the secondary set of antenna array radiates at a power lower than Pmin, the 100-percent intensity modulation of HFPLs will not be observed. The functional dependence of Pmin on the difference frequency of the two sets of antenna array is also predicted for future experiments to corroborate.

A Heterogeneous Wireless Identification Network for the Localization of Animals Based on Stochastic Movements

PubMed Central

Gutiérrez, Álvaro; González, Carlos; Jiménez-Leube, Javier; Zazo, Santiago; Dopico, Nelson; Raos, Ivana

2009-01-01

The improvement in the transmission range in wireless applications without the use of batteries remains a significant challenge in identification applications. In this paper, we describe a heterogeneous wireless identification network mostly powered by kinetic energy, which allows the localization of animals in open environments. The system relies on radio communications and a global positioning system. It is made up of primary and secondary nodes. Secondary nodes are kinetic-powered and take advantage of animal movements to activate the node and transmit a specific identifier, reducing the number of batteries of the system. Primary nodes are battery-powered and gather secondary-node transmitted information to provide it, along with position and time data, to a final base station in charge of the animal monitoring. The system allows tracking based on contextual information obtained from statistical data. PMID:22412344

Steps Toward Optimal Competitive Scheduling

NASA Technical Reports Server (NTRS)

Frank, Jeremy; Crawford, James; Khatib, Lina; Brafman, Ronen

2006-01-01

This paper is concerned with the problem of allocating a unit capacity resource to multiple users within a pre-defined time period. The resource is indivisible, so that at most one user can use it at each time instance. However, different users may use it at different times. The users have independent, se@sh preferences for when and for how long they are allocated this resource. Thus, they value different resource access durations differently, and they value different time slots differently. We seek an optimal allocation schedule for this resource. This problem arises in many institutional settings where, e.g., different departments, agencies, or personal, compete for a single resource. We are particularly motivated by the problem of scheduling NASA's Deep Space Satellite Network (DSN) among different users within NASA. Access to DSN is needed for transmitting data from various space missions to Earth. Each mission has different needs for DSN time, depending on satellite and planetary orbits. Typically, the DSN is over-subscribed, in that not all missions will be allocated as much time as they want. This leads to various inefficiencies - missions spend much time and resource lobbying for their time, often exaggerating their needs. NASA, on the other hand, would like to make optimal use of this resource, ensuring that the good for NASA is maximized. This raises the thorny problem of how to measure the utility to NASA of each allocation. In the typical case, it is difficult for the central agency, NASA in our case, to assess the value of each interval to each user - this is really only known to the users who understand their needs. Thus, our problem is more precisely formulated as follows: find an allocation schedule for the resource that maximizes the sum of users preferences, when the preference values are private information of the users. We bypass this problem by making the assumptions that one can assign money to customers. This assumption is reasonable; a committee is usually in charge of deciding the priority of each mission competing for access to the DSN within a time period while scheduling. Instead, we can assume that the committee assigns a budget to each mission.This paper is concerned with the problem of allocating a unit capacity resource to multiple users within a pre-defined time period. The resource is indivisible, so that at most one user can use it at each time instance. However, different users may use it at different times. The users have independent, se@sh preferences for when and for how long they are allocated this resource. Thus, they value different resource access durations differently, and they value different time slots differently. We seek an optimal allocation schedule for this resource. This problem arises in many institutional settings where, e.g., different departments, agencies, or personal, compete for a single resource. We are particularly motivated by the problem of scheduling NASA's Deep Space Satellite Network (DSN) among different users within NASA. Access to DSN is needed for transmitting data from various space missions to Earth. Each mission has different needs for DSN time, depending on satellite and planetary orbits. Typically, the DSN is over-subscribed, in that not all missions will be allocated as much time as they want. This leads to various inefficiencies - missions spend much time and resource lobbying for their time, often exaggerating their needs. NASA, on the other hand, would like to make optimal use of this resource, ensuring that the good for NASA is maximized. This raises the thorny problem of how to measure the utility to NASA of each allocation. In the typical case, it is difficult for the central agency, NASA in our case, to assess the value of each interval to each user - this is really only known to the users who understand their needs. Thus, our problem is more precisely formulated as follows: find an allocation schedule for the resource that maximizes the sum ofsers preferences, when the preference values are private information of the users. We bypass this problem by making the assumptions that one can assign money to customers. This assumption is reasonable; a committee is usually in charge of deciding the priority of each mission competing for access to the DSN within a time period while scheduling. Instead, we can assume that the committee assigns a budget to each mission.

Experimental implementation of array-compressed parallel transmission at 7 tesla.

PubMed

Yan, Xinqiang; Cao, Zhipeng; Grissom, William A

2016-06-01

To implement and validate a hardware-based array-compressed parallel transmission (acpTx) system. In array-compressed parallel transmission, a small number of transmit channels drive a larger number of transmit coils, which are connected via an array compression network that implements optimized coil-to-channel combinations. A two channel-to-eight coil array compression network was developed using power splitters, attenuators and phase shifters, and a simulation was performed to investigate the effects of coil coupling on power dissipation in a simplified network. An eight coil transmit array was constructed using induced current elimination decoupling, and the coil and network were validated in benchtop measurements, B1+ mapping scans, and an accelerated spiral excitation experiment. The developed attenuators came within 0.08 dB of the desired attenuations, and reflection coefficients were -22 dB or better. The simulation demonstrated that up to 3× more power was dissipated in the network when coils were poorly isolated (-9.6 dB), versus well-isolated (-31 dB). Compared to split circularly-polarized coil combinations, the additional degrees of freedom provided by the array compression network led to 54% lower squared excitation error in the spiral experiment. Array-compressed parallel transmission was successfully implemented in a hardware system. Further work is needed to develop remote network tuning and to minimize network power dissipation. Magn Reson Med 75:2545-2552, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

18 CFR 284.10 - Rates.

Code of Federal Regulations, 2012 CFR

2012-04-01

... based on the average variable costs which are properly allocated to the service to which the rate... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Rates. 284.10 Section 284.10 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

18 CFR 284.10 - Rates.

Code of Federal Regulations, 2013 CFR

2013-04-01

... based on the average variable costs which are properly allocated to the service to which the rate... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Rates. 284.10 Section 284.10 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

18 CFR 284.10 - Rates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... based on the average variable costs which are properly allocated to the service to which the rate... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Rates. 284.10 Section 284.10 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

18 CFR 284.10 - Rates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... based on the average variable costs which are properly allocated to the service to which the rate... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Rates. 284.10 Section 284.10 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

18 CFR 284.10 - Rates.

Code of Federal Regulations, 2014 CFR

2014-04-01

... based on the average variable costs which are properly allocated to the service to which the rate... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Rates. 284.10 Section 284.10 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF...

A Bayesian adaptive design for biomarker trials with linked treatments

PubMed Central

Wason, James M S; Abraham, Jean E; Baird, Richard D; Gournaris, Ioannis; Vallier, Anne-Laure; Brenton, James D; Earl, Helena M; Mander, Adrian P

2015-01-01

Background: Response to treatments is highly heterogeneous in cancer. Increased availability of biomarkers and targeted treatments has led to the need for trial designs that efficiently test new treatments in biomarker-stratified patient subgroups. Methods: We propose a novel Bayesian adaptive randomisation (BAR) design for use in multi-arm phase II trials where biomarkers exist that are potentially predictive of a linked treatment's effect. The design is motivated in part by two phase II trials that are currently in development. The design starts by randomising patients to the control treatment or to experimental treatments that the biomarker profile suggests should be active. At interim analyses, data from treated patients are used to update the allocation probabilities. If the linked treatments are effective, the allocation remains high; if ineffective, the allocation changes over the course of the trial to unlinked treatments that are more effective. Results: Our proposed design has high power to detect treatment effects if the pairings of treatment with biomarker are correct, but also performs well when alternative pairings are true. The design is consistently more powerful than parallel-groups stratified trials. Conclusions: This BAR design is a powerful approach to use when there are pairings of biomarkers with treatments available for testing simultaneously. PMID:26263479

National Streamflow Information Program: Implementation Status Report

USGS Publications Warehouse

Norris, J. Michael

2009-01-01

The U.S. Geological Survey (USGS) operates and maintains a nationwide network of about 7,500 streamgages designed to provide and interpret long-term, accurate, and unbiased streamflow information to meet the multiple needs of many diverse national, regional, state, and local users. The National Streamflow Information Program (NSIP) was initiated in 2003 in response to Congressional and stakeholder concerns about (1) the decrease in the number of operating streamgages, including a disproportionate loss of streamgages with a long period of record; (2) the inability of the USGS to continue operating high-priority streamgages in an environment of reduced funding through partnerships; and (3) the increasing demand for streamflow information due to emerging resource-management issues and new data-delivery capabilities. The NSIP's mission is to provide the streamflow information and understanding required to meet national, regional, state, and local needs. Most of the existing streamgages are funded through partnerships with more than 850 other Federal, state, tribal, and local agencies. Currently, about 90 percent of the streamgages send data to the World Wide Web in near-real time (some information is transmitted within 15 minutes, whereas some lags by about 4 hours). The streamflow information collected at USGS streamgages is used for many purposes: *In water-resource appraisals and allocations - to determine how much water is available and how it is being allocated; *To provide streamflow information required by interstate agreements, compacts, and court decrees; *For engineering design of reservoirs, bridges, roads, culverts, and treatment plants; *For the operation of reservoirs, the operation of locks and dams for navigation purposes, and power production; *To identify changes in streamflow resulting from changes in land use, water use, and climate; *For streamflow forecasting, flood planning, and flood forecasting; *To support water-quality programs by allowing determination of constituent loads and fluxes; and *For characterizing and evaluating instream conditions for habitat assessments, instream-flow requirements, and recreation.

Space Solar Power: Satellite Concepts

NASA Technical Reports Server (NTRS)

Little, Frank E.

1999-01-01

Space Solar Power (SSP) applies broadly to the use of solar power for space related applications. The thrust of the NASA SSP initiative is to develop concepts and demonstrate technology for applying space solar power to NASA missions. Providing power from satellites in space via wireless transmission to a receiving station either on earth, another celestial body or a second satellite is one goal of the SSP initiative. The sandwich design is a satellite design in which the microwave transmitting array is the front face of a thin disk and the back of the disk is populated with solar cells, with the microwave electronics in between. The transmitter remains aimed at the earth in geostationary orbit while a system of mirrors directs sunlight to the photovoltaic cells, regardless of the satellite's orientation to the sun. The primary advantage of the sandwich design is it eliminates the need for a massive and complex electric power management and distribution system for the satellite. However, it requires a complex system for focusing sunlight onto the photovoltaic cells. In addition, positioning the photovoltaic array directly behind the transmitting array power conversion electronics will create a thermal management challenge. This project focused on developing designs and finding emerging technology to meet the challenges of solar tracking, a concentrating mirror system including materials and coatings, improved photovoltaic materials and thermal management.

Compensating for Tissue Changes in an Ultrasonic Power Link for Implanted Medical Devices.

PubMed

Vihvelin, Hugo; Leadbetter, Jeff; Bance, Manohar; Brown, Jeremy A; Adamson, Robert B A

2016-04-01

Ultrasonic power transfer using piezoelectric devices is a promising wireless power transfer technology for biomedical implants. However, for sub-dermal implants where the separation between the transmitter and receiver is on the order of several acoustic wavelengths, the ultrasonic power transfer efficiency (PTE) is highly sensitive to the distance between the transmitter and receiver. This sensitivity can cause large swings in efficiency and presents a serious limitation on battery life and overall performance. A practical ultrasonic transcutaneous energy transfer (UTET) system design must accommodate different implant depths and unpredictable acoustic changes caused by tissue growth, hydration, ambient temperature, and movement. This paper describes a method used to compensate for acoustic separation distance by varying the transmit (Tx) frequency in a UTET system. In a benchtop UTET system we experimentally show that without compensation, power transfer efficiency can range from 9% to 25% as a 5 mm porcine tissue sample is manipulated to simulate in situ implant conditions. Using an active frequency compensation method, we show that the power transfer efficiency can be kept uniformly high, ranging from 20% to 27%. The frequency compensation strategy we propose is low-power, non-invasive, and uses only transmit-side measurements, making it suitable for active implanted medical device applications.

Free-space microwave-power transmission

NASA Technical Reports Server (NTRS)

Brown, W. C.

1976-01-01

Laboratory-scale wireless transmission of microwave power approaches fifty-four percent efficiency. DC is converted to a 2.45-GHz signal and is transmitted through horn antenna array; microwave signal is received at rectenna and is simultaneously collected and rectified back to dc at receiving sites; dc is then processed for wired distribution.

75 FR 17681 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-07

... generate or purchase power and transmit the power to the distribution systems. All RUS and G&T borrowers... Assistance and Training Grant Program--Recovery Act Funding. OMB Control Number: 0572-0144. Summary of Collection: The American Recovery and Reinvestment Act of 2009 (Recovery Act) provides for the availability...

76 FR 67430 - Application To Export Electric Energy; Tenaska Power Services Co.

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-01

... Services Co. AGENCY: Office of Electricity Delivery and Energy Reliability, DOE. ACTION: Notice of application. SUMMARY: Tenaska Power Services Co. (Tenaska) has applied to renew its authority to transmit... of Electricity Delivery and Energy Reliability, Mail Code: OE-20, U.S. Department of Energy, 1000...

Sub-millimeter wave frequency heterodyne detector system

NASA Technical Reports Server (NTRS)

Siegel, Peter H. (Inventor); Dengler, Robert (Inventor); Mueller, Eric R. (Inventor)

2009-01-01

The present invention relates to sub-millimeter wave frequency heterodyne imaging systems. More specifically, the present invention relates to a sub-millimeter wave frequency heterodyne detector system for imaging the magnitude and phase of transmitted power through or reflected power off of mechanically scanned samples at sub-millimeter wave frequencies.

Sub-millimeter wave frequency heterodyne detector system

NASA Technical Reports Server (NTRS)

Siegel, Peter H. (Inventor); Dengler, Robert (Inventor); Mueller, Eric R. (Inventor)

2010-01-01

The present invention relates to sub-millimeter wave frequency heterodyne imaging systems. More specifically, the present invention relates to a sub-millimeter wave frequency heterodyne detector system for imaging the magnitude and phase of transmitted power through or reflected power off of mechanically scanned samples at sub-millimeter wave frequencies.

Government: Nuclear Safety in Doubt a Year after Accident.

ERIC Educational Resources Information Center

Ember, Lois R.

1980-01-01

A year after the accident at Three Mile Island (TMI), the signals transmitted to the public are still confused. Industry says that nuclear power is safe and that the aftermath of TMI ushers in a new era of safety. Antinuclear activists say TMI sounded nuclear power's death knell. (Author/RE)

Effects of a Meditation Program on Nurses' Power and Quality of Life.

PubMed

Chang, Sun Ju; Kwak, Eun Young; Hahm, Bong-Jin; Seo, Se Hee; Lee, Da Woon; Jang, Sun Joo

2016-07-01

This study evaluated the effects of meditation programs on nurses' power and quality of life. In this study, Barrett's power theory derived from Rogers' unitary human being science was used as a theoretical framework. A randomized controlled design with 50 recruited and randomly allocated participants was used. The results demonstrated that the eight-week meditation program significantly improved nurses' power and quality of life. These results suggest that meditation has positive effects on power and quality of life. © The Author(s) 2016.

Automated electric power management and control for Space Station Freedom

NASA Technical Reports Server (NTRS)

Dolce, James L.; Mellor, Pamela A.; Kish, James A.

1990-01-01

A comprehensive automation design is being developed for Space Station Freedom's electric power system. It strives to increase station productivity by applying expert systems and conventional algorithms to automate power system operation. An integrated approach to the power system command and control problem is defined and used to direct technology development in: diagnosis, security monitoring and analysis, battery management, and cooperative problem-solving for resource allocation. The prototype automated power system is developed using simulations and test-beds.

Invasion fitness for gene-culture co-evolution in family-structured populations and an application to cumulative culture under vertical transmission.

PubMed

Mullon, Charles; Lehmann, Laurent

2017-08-01

Human evolution depends on the co-evolution between genetically determined behaviors and socially transmitted information. Although vertical transmission of cultural information from parent to offspring is common in hominins, its effects on cumulative cultural evolution are not fully understood. Here, we investigate gene-culture co-evolution in a family-structured population by studying the invasion fitness of a mutant allele that influences a deterministic level of cultural information (e.g., amount of knowledge or skill) to which diploid carriers of the mutant are exposed in subsequent generations. We show that the selection gradient on such a mutant, and the concomitant level of cultural information it generates, can be evaluated analytically under the assumption that the cultural dynamic has a single attractor point, thereby making gene-culture co-evolution in family-structured populations with multigenerational effects mathematically tractable. We apply our result to study how genetically determined phenotypes of individual and social learning co-evolve with the level of adaptive information they generate under vertical transmission. We find that vertical transmission increases adaptive information due to kin selection effects, but when information is transmitted as efficiently between family members as between unrelated individuals, this increase is moderate in diploids. By contrast, we show that the way resource allocation into learning trades off with allocation into reproduction (the "learning-reproduction trade-off") significantly influences levels of adaptive information. We also show that vertical transmission prevents evolutionary branching and may therefore play a qualitative role in gene-culture co-evolutionary dynamics. More generally, our analysis of selection suggests that vertical transmission can significantly increase levels of adaptive information under the biologically plausible condition that information transmission between relatives is more efficient than between unrelated individuals. Copyright © 2017 Elsevier Inc. All rights reserved.

Meteor burst communications for LPI applications

NASA Astrophysics Data System (ADS)

Schilling, D. L.; Apelewicz, T.; Lomp, G. R.; Lundberg, L. A.

A technique that enhances the performance of meteor-burst communications is described. The technique, the feedback adaptive variable rate (FAVR) system, maintains a feedback channel that allows the transmitted bit rate to mimic the time behavior of the received power so that a constant bit energy is maintained. This results in a constant probability of bit error in each transmitted bit. Experimentally determined meteor-burst channel characteristics and FAVR system simulation results are presented.

Opportunistic Capacity-Based Resource Allocation for Chunk-Based Multi-Carrier Cognitive Radio Sensor Networks

PubMed Central

Huang, Jie; Zeng, Xiaoping; Jian, Xin; Tan, Xiaoheng; Zhang, Qi

2017-01-01

The spectrum allocation for cognitive radio sensor networks (CRSNs) has received considerable research attention under the assumption that the spectrum environment is static. However, in practice, the spectrum environment varies over time due to primary user/secondary user (PU/SU) activity and mobility, resulting in time-varied spectrum resources. This paper studies resource allocation for chunk-based multi-carrier CRSNs with time-varied spectrum resources. We present a novel opportunistic capacity model through a continuous time semi-Markov chain (CTSMC) to describe the time-varied spectrum resources of chunks and, based on this, a joint power and chunk allocation model by considering the opportunistically available capacity of chunks is proposed. To reduce the computational complexity, we split this model into two sub-problems and solve them via the Lagrangian dual method. Simulation results illustrate that the proposed opportunistic capacity-based resource allocation algorithm can achieve better performance compared with traditional algorithms when the spectrum environment is time-varied. PMID:28106803

Technologies for Lunar Surface Power Systems Power Beaming and Transfer

NASA Astrophysics Data System (ADS)

Marzwell, Neville; Pogorzelski, Ronald J.; Chang, Kai; Little, Frank

2008-01-01

Wireless power transmission within a given working area is required or enabling for many NASA Exploration Systems. Fields of application include robotics, habitats, autonomous rendezvous and docking, life support, EVA, and many others. In robotics applications, for example, the robots must move in the working area without being hampered by power cables and, meanwhile, obtain a continuous and constant power from a power transmitter. The development of modern technology for transmitting electric power over free space has been studied for several decades, but its use in a system has been mainly limited to low power, 1-2 Vdc output voltage at a transmission distance of few meters for which relatively less than 0.5 mW/cm2 is required (e.g., Radio frequency identification RFID). Most of the rectenna conversion efficiency research to date has concentrated in low GHz frequency range of 2.45 to 10 GHz, with some work at 35 GHz. However, for space application, atmospheric adsorbtion is irrelevant and higher frequency systems with smaller transmit and receive apertures may be appropriate. For high power, most of the work on rectennas has concentrated on optimizing the conversion efficiency of the microwave rectifier element; the highest power demonstrated was 35 kW of power over a distance of 1.5 km. The objective of this paper is to establish the manner in which a very large number of very low power microwave devices can be synchronized to provide a beam of microwaves that can be used to efficiently and safely transport a significant amount of power to a remote location where it can be converted to dc (or ac) power by a ``rectenna.'' The proposed system is based on spatial power combining of the outputs of a large number of devices synchronized by mutual injection locking. We have demonstrated at JPL that such power could be achieved by combining 25 sources in a configuration that allows for convenient steering of the resulting beam of microwaves. Retrodirective beam steering for microwave power transmission (the ability to accurately track a moving receiver) has been demonstrated at Texas A&M. It is proposed that the next step in development of this concept is a modest scale up from 25 elements to 435 followed by a further scale up using such 435 element arrays as subarrays for a still larger retrodirective system. Ultimately, transmit antenna sizes on the order of 100 meters are envisioned permitting transfer levels on the order of 30 kW to aerial vehicles up to 20 km.

CARBON AND NITROGEN ALLOCATION MODEL FOR THE SEAGRASS THALASSIA TESTUDUNUM IN LOWER LAGUNA MADRE

EPA Science Inventory

Inverse modeling methods are a powerful tool for understanding complex physiological relationships between seagrasses and their environment. The power of the method is a result of using ranges of data in a system of constraints to describe the biological system, in this case, t...

Full-Duplex Digital Communication on a Single Laser Beam

NASA Technical Reports Server (NTRS)

Hazzard, D. A.; MacCannell, J. A.; Lee, G.; Selves, E. R.; Moore, D.; Payne, J. A.; Garrett, C. D.; Dahlstrom, N.; Shay, T. M.

2006-01-01

A proposed free-space optical communication system would operate in a full-duplex mode, using a single constant-power laser beam for transmission and reception of binary signals at both ends of the free-space optical path. The system was conceived for two-way data communication between a ground station and a spacecraft in a low orbit around the Earth. It has been estimated that in this application, a data rate of 10 kb/s could be achieved at a ground-station-to-spacecraft distance of 320 km, using a laser power of only 100 mW. The basic system concept is also applicable to terrestrial free-space optical communications. The system (see figure) would include a diode laser at one end of the link (originally, the ground station) and a liquid-crystal- based retroreflecting modulator at the other end of the link (originally, the spacecraft). At the laser end, the beam to be transmitted would be made to pass through a quarter-wave plate, which would convert its linear polarization to right circular polarization. For transmission of data from the laser end to the retroreflector end, the laser beam would be modulated with subcarrier phase-shift keying (SC-PSK). The transmitted beam would then pass through an aperture- sharing element (ASE) - basically, a mirror with a hole in it, used to separate the paths of the transmitted and received light beams. The transmitted beam would continue outward through a telescope (which, in the original application, would be equipped with a spacecraft-tracking system) that would launch the transmitted beam along the free-space optical path to the retroreflector end.

High performance monolithic power management system with dynamic maximum power point tracking for microbial fuel cells.

PubMed

Erbay, Celal; Carreon-Bautista, Salvador; Sanchez-Sinencio, Edgar; Han, Arum

2014-12-02

Microbial fuel cell (MFC) that can directly generate electricity from organic waste or biomass is a promising renewable and clean technology. However, low power and low voltage output of MFCs typically do not allow directly operating most electrical applications, whether it is supplementing electricity to wastewater treatment plants or for powering autonomous wireless sensor networks. Power management systems (PMSs) can overcome this limitation by boosting the MFC output voltage and managing the power for maximum efficiency. We present a monolithic low-power-consuming PMS integrated circuit (IC) chip capable of dynamic maximum power point tracking (MPPT) to maximize the extracted power from MFCs, regardless of the power and voltage fluctuations from MFCs over time. The proposed PMS continuously detects the maximum power point (MPP) of the MFC and matches the load impedance of the PMS for maximum efficiency. The system also operates autonomously by directly drawing power from the MFC itself without any external power. The overall system efficiency, defined as the ratio between input energy from the MFC and output energy stored into the supercapacitor of the PMS, was 30%. As a demonstration, the PMS connected to a 240 mL two-chamber MFC (generating 0.4 V and 512 μW at MPP) successfully powered a wireless temperature sensor that requires a voltage of 2.5 V and consumes power of 85 mW each time it transmit the sensor data, and successfully transmitted a sensor reading every 7.5 min. The PMS also efficiently managed the power output of a lower-power producing MFC, demonstrating that the PMS works efficiently at various MFC power output level.

Torque Transmission Device at Zero Leakage

NASA Technical Reports Server (NTRS)

Hendricks, R. C.; Mullen, R. L.

2005-01-01

In a few critical applications, mechanical transmission of power by rotation at low speed is required without leakage at an interface. Herein we examine a device that enables torque to be transmitted across a sealed environmental barrier. The barrier represents the restraint membrane through which the torque is transmitted. The power is transferred through elastic deformation of a circular tube into an elliptical cross-section. Rotation of the principle axis of the ellipse at one end results in a commensurate rotation of an elliptical cross section at the other end of the tube. This transfer requires no rigid body rotation of the tube allowing a membrane to seal one end from the other. Both computational and experimental models of the device are presented.

Long-range, full-duplex, modulated-reflector cell phone for voice/data transmission

DOEpatents

Neagley, Daniel L.; Briles, Scott D.; Coates, Don M.; Freund, Samuel M.

2002-01-01

A long-range communications apparatus utilizing modulated-reflector technology is described. The apparatus includes an energy-transmitting base station and remote units that do not emit radiation in order to communicate with the base station since modulated-reflector technology is used whereby information is attached to an RF carrier wave originating from the base station which is reflected by the remote unit back to the base station. Since the remote unit does not emit radiation, only a low-power power source is required for its operation. Information from the base station is transmitted to the remote unit using a transmitter and receiver, respectively. The range of such a communications system is determined by the properties of a modulated-reflector half-duplex link.

Ka-Band MMIC Subarray Technology Program (Ka-Mist)

NASA Technical Reports Server (NTRS)

Pottinger, W.

1995-01-01

Ka-band monolithic microwave integrated circuit (MMIC) arrays have been considered as having high potential for increasing the capability of space, aircraft, and land mobile communication systems in terms of scan performance, data rate, link margin, and flexibility while offering a significant reduction in size, weight, and power consumption. Insertion of MMIC technology into antenna systems, particularly at millimeter wave frequencies using low power and low noise amplifiers in closed proximity to the radiating elements, offers a significant improvement in the array transmit efficiency, receive system noise figure, and overall array reliability. Application of active array technology also leads to the use of advanced beamforming techniques that can improve beam agility, diversity, and adaptivity to complex signal environments. The objective of this program was to demonstrate the technical feasibility of the 'tile' array packaging architecture at EHF via the insertion of 1990 MMIC technology into a functional tile array or subarray module. The means test of this objective was to demonstrate and deliver to NASA a minimum of two 4 x 4 (16 radiating element) subarray modules operating in a transmit mode at 29.6 GHz. Available (1990) MMIC technology was chosen to focus the program effort on the novel interconnect schemes and packaging requirements rather than focusing on MMIC development. Major technical achievements of this program include the successful integration of two 4 x 4 subarray modules into a single antenna array. This 32 element array demonstrates a transmit EIRP of over 300 watts yielding an effective directive power gain in excess of 55 dB at 29.63 GHz. The array has been actively used as the transmit link in airborne/terrestrial mobile communication experiments accomplished via the ACTS satellite launched in August 1993.

Effect of self-care training program based on Orem's model on the behaviors leading to sexually transmitted disease in vulnerable women.

PubMed

Baghersad, Zahra; Alimohammadi, Nasrollah; Boroumandfar, Zahra; Golshiri, Parastoo

2016-01-01

Vulnerable women are prone to sexually transmitted diseases due to their high-risk behaviors. The present study aimed to investigate the effect of self-care training program based on Orem's model on the behaviors leading to sexually transmitted diseases in vulnerable women. This field trial was initially conducted on 100 women covered under health services and welfare organization in Isfahan city, who were selected by rationing ssampling. For needs assessment, they filled the self-care needs assessment questionnaire in three domains of knowledge, attitude, and practice. Then, at the stage of intervention (self-care training), 64 subjects were selected through convenient sampling and were assigned to experimental and control groups by random allocation. Data were analyzed by descriptive and analytical statistical tests through SPSS 18. Results showed that mean scores of knowledge ( P < 0.001), attitude ( P < 0.001), practice ( P = 0.04), and behavior change ( P = 0.01) were significantly higher immediately after and 3 months after intervention, compared to before intervention, but there was no significant difference in mean scores between immediately after and 3 months after intervention. With regard to these results, it can be concluded that if the educational programs are planned based on clients' real needs assessment, the learners follow the educational materials, related to their problems, more seriously and it results in a notable behavior change in them.

Power Management in Regenerative Life Support Systems

NASA Technical Reports Server (NTRS)

Crawford, Sekou; Pawlowski, Christopher; Finn, Cory; Mead, Susan C. (Technical Monitor)

1999-01-01

Effective management of power can reduce the cost of launch and operation of regenerative life support systems. Variations in power may be quite severe and may manifest as surges or spikes, While the power plant may have some ability to deal with these variations, with batteries for example, over-capacity is expensive and does nothing to address the fundamental issue of excessive demand. Because the power unit must be sized to accommodate the largest demand, avoiding power spikes has the potential to reduce the required size of the power plant while at the same time increasing the dependability of the system. Scheduling of processors can help to reduce potential power spikes. However, not all power-consuming equipment is easily scheduled. Therefore, active power management is needed to further decrease the risk of surges or spikes. We investigate the use of a hierarchical scheme to actively manage power for a model of a regenerative life support system. Local level controllers individually determine subsystem power usage. A higher level controller monitors overall system power and detects surges or spikes. When a surge condition is detected, the higher level controller conducts an 'auction' and describes subsystem power usage to re-allocate power. The result is an overall reduction in total power during a power surge. The auction involves each subsystem making a 'bid' to buy or sell power based on local needs. However, this re-allocation cannot come at the expense of life support function. To this end, participation in the auction is restricted to those processes meeting certain tolerance constraints. These tolerances represent acceptable limits within which system processes can be operated. We present a simulation model and discuss some of our results.

AN/TPN-14 Precision Approach Radar (PAR) Analysis

DTIC Science & Technology

1964-05-01

to install high -pass filters on the transmitter power lines, or (2) change the PRF to, for example, 1400 cps to give maximum separation of the PRF...consist of a high voltage power supply, pulse forming and transmitting circuitry, and necessary control circuitry. It shall have a pulse type...1200 cycles per second and a pulse width of 0. 2 or 0. 8 microseconds selectable. 3. 5. 5. 1 High voltage power supply. - The high voltage power

Electricity production from municipal solid waste using microbial fuel cells.

PubMed

Chiu, H Y; Pai, T Y; Liu, M H; Chang, C A; Lo, F C; Chang, T C; Lo, H M; Chiang, C F; Chao, K P; Lo, W Y; Lo, S W; Chu, Y L

2016-07-01

The organic content of municipal solid waste has long been an attractive source of renewable energy, mainly as a solid fuel in waste-to-energy plants. This study focuses on the potential to use microbial fuel cells to convert municipal solid waste organics into energy using various operational conditions. The results showed that two-chamber microbial fuel cells with carbon felt and carbon felt allocation had a higher maximal power density (20.12 and 30.47 mW m(-2) for 1.5 and 4 L, respectively) than those of other electrode plate allocations. Most two-chamber microbial fuel cells (1.5 and 4 L) had a higher maximal power density than single-chamber ones with corresponding electrode plate allocations. Municipal solid waste with alkali hydrolysis pre-treatment and K3Fe(CN)6 as an electron acceptor improved the maximal power density to 1817.88 mW m(-2) (~0.49% coulomb efficiency, from 0.05-0.49%). The maximal power density from experiments using individual 1.5 and 4 L two-chamber microbial fuel cells, and serial and parallel connections of 1.5 and 4 L two-chamber microbial fuel cells, was found to be in the order of individual 4 L (30.47 mW m(-2)) > serial connection of 1.5 and 4 L (27.75) > individual 1.5 L (20.12) > parallel connection of 1.5 and 4 L (17.04) two-chamber microbial fuel cells . The power density using municipal solid waste microbial fuel cells was compared with information in the literature and discussed. © The Author(s) 2016.

Noninferiority trial designs for odds ratios and risk differences.

PubMed

Hilton, Joan F

2010-04-30

This study presents constrained maximum likelihood derivations of the design parameters of noninferiority trials for binary outcomes with the margin defined on the odds ratio (ψ) or risk-difference (δ) scale. The derivations show that, for trials in which the group-specific response rates are equal under the point-alternative hypothesis, the common response rate, π(N), is a fixed design parameter whose value lies between the control and experimental rates hypothesized at the point-null, {π(C), π(E)}. We show that setting π(N) equal to the value of π(C) that holds under H(0) underestimates the overall sample size requirement. Given {π(C), ψ} or {π(C), δ} and the type I and II error rates, or algorithm finds clinically meaningful design values of π(N), and the corresponding minimum asymptotic sample size, N=n(E)+n(C), and optimal allocation ratio, γ=n(E)/n(C). We find that optimal allocations are increasingly imbalanced as ψ increases, with γ(ψ)<1 and γ(δ)≈1/γ(ψ), and that ranges of allocation ratios map to the minimum sample size. The latter characteristic allows trialists to consider trade-offs between optimal allocation at a smaller N and a preferred allocation at a larger N. For designs with relatively large margins (e.g. ψ>2.5), trial results that are presented on both scales will differ in power, with more power lost if the study is designed on the risk-difference scale and reported on the odds ratio scale than vice versa. 2010 John Wiley & Sons, Ltd.

Attention is allocated closely ahead of the target during smooth pursuit eye movements: Evidence from EEG frequency tagging.

PubMed

Chen, Jing; Valsecchi, Matteo; Gegenfurtner, Karl R

2017-07-28

It is under debate whether attention during smooth pursuit is centered right on the pursuit target or allocated preferentially ahead of it. Attentional deployment was previously probed using a secondary task, which might have altered attention allocation and led to inconsistent findings. We measured frequency-tagged steady-state visual evoked potentials (SSVEP) to measure attention allocation in the absence of any secondary probing task. The observers pursued a moving dot while stimuli flickering at different frequencies were presented at various locations ahead or behind the pursuit target. We observed a significant increase in EEG power at the flicker frequency of the stimulus in front of the pursuit target, compared to the frequency of the stimulus behind. When testing many different locations, we found that the enhancement was detectable up to about 1.5° ahead during pursuit, but vanished by 3.5°. In a control condition using attentional cueing during fixation, we did observe an enhanced EEG response to stimuli at this eccentricity, indicating that the focus of attention during pursuit is narrower than allowed for by the resolution of the attentional system. In a third experiment, we ruled out the possibility that the SSVEP enhancement was a byproduct of the catch-up saccades occurring during pursuit. Overall, we showed that attention is on average allocated ahead of the pursuit target during smooth pursuit. EEG frequency tagging seems to be a powerful technique that allows for the investigation of attention/perception implicitly when an overt task would be confounding. Copyright © 2017 Elsevier Ltd. All rights reserved.

A video wireless capsule endoscopy system powered wirelessly: design, analysis and experiment

NASA Astrophysics Data System (ADS)

Pan, Guobing; Xin, Wenhui; Yan, Guozheng; Chen, Jiaoliao

2011-06-01

Wireless capsule endoscopy (WCE), as a relatively new technology, has brought about a revolution in the diagnosis of gastrointestinal (GI) tract diseases. However, the existing WCE systems are not widely applied in clinic because of the low frame rate and low image resolution. A video WCE system based on a wireless power supply is developed in this paper. This WCE system consists of a video capsule endoscope (CE), a wireless power transmission device, a receiving box and an image processing station. Powered wirelessly, the video CE has the abilities of imaging the GI tract and transmitting the images wirelessly at a frame rate of 30 frames per second (f/s). A mathematical prototype was built to analyze the power transmission system, and some experiments were performed to test the capability of energy transferring. The results showed that the wireless electric power supply system had the ability to transfer more than 136 mW power, which was enough for the working of a video CE. In in vitro experiments, the video CE produced clear images of the small intestine of a pig with the resolution of 320 × 240, and transmitted NTSC format video outside the body. Because of the wireless power supply, the video WCE system with high frame rate and high resolution becomes feasible, and provides a novel solution for the diagnosis of the GI tract in clinic.

A new type of coil structure called pan-shaped coil of wireless charging system based on magnetic resonance

NASA Astrophysics Data System (ADS)

Yue, Z. K.; Liu, Z. Z.; Hou, Y. J.; Zeng, H.; Liang, L. H.; Cui, S.

2017-11-01

The problem that misalignment between the transmitting coil and the receiving coil significantly impairs the transmission power and efficiency of the system has been attached more and more attention. In order to improve the uniformity of the magnetic field between the two coils to solve this problem, a new type of coil called pan-shaped coil is proposed. Three-dimension simulation models of the planar-core coil and the pan-shaped coil are established using Ansoft Maxwell software. The coupling coefficient between the transmitting coil and the receiving coil is obtained by simulating the magnetic field with the receiving coil misalignment or not. And the maximum percentage difference strength along the radial direction which is defined as the magnetic field uniformity factor is calculated. According to the simulation results of the two kinds of coil structures, it is found that the new type of coil structure can obviously improve the uniformity of the magnetic field, coupling coefficient and power transmission properties between the transmitting coil and the receiving coil.

Peak-to-average power ratio reduction in orthogonal frequency division multiplexing-based visible light communication systems using a modified partial transmit sequence technique

NASA Astrophysics Data System (ADS)

Liu, Yan; Deng, Honggui; Ren, Shuang; Tang, Chengying; Qian, Xuewen

2018-01-01

We propose an efficient partial transmit sequence technique based on genetic algorithm and peak-value optimization algorithm (GAPOA) to reduce high peak-to-average power ratio (PAPR) in visible light communication systems based on orthogonal frequency division multiplexing (VLC-OFDM). By analysis of hill-climbing algorithm's pros and cons, we propose the POA with excellent local search ability to further process the signals whose PAPR is still over the threshold after processed by genetic algorithm (GA). To verify the effectiveness of the proposed technique and algorithm, we evaluate the PAPR performance and the bit error rate (BER) performance and compare them with partial transmit sequence (PTS) technique based on GA (GA-PTS), PTS technique based on genetic and hill-climbing algorithm (GH-PTS), and PTS based on shuffled frog leaping algorithm and hill-climbing algorithm (SFLAHC-PTS). The results show that our technique and algorithm have not only better PAPR performance but also lower computational complexity and BER than GA-PTS, GH-PTS, and SFLAHC-PTS technique.

Poynting vector analysis for wireless power transfer between magnetically coupled coils with different loads.

PubMed

Guo, Yunsheng; Li, Jiansheng; Hou, Xiaojuan; Lv, Xiaolong; Liang, Hao; Zhou, Ji; Wu, Hongya

2017-04-07

Wireless power transfer is a nonradiative type of transmission that is performed in the near-field region. In this region, the electromagnetic fields that are produced by both the transmitting and receiving coils are evanescent fields, which should not transmit energy. This then raises the question of how the energy can be transferred. Here we describe a theoretical study of the two evanescent field distributions at different terminal loads. It is shown that the essential principle of wireless energy transfer is the superposition of the two evanescent fields, and the resulting superimposed field is mediated through the terminal load. If the terminal load is either capacitive or inductive, then the superimposed field cannot transfer the energy because its Poynting vector is zero; in contrast, if the load is resistive, energy can then be conveyed from the transmitting coil to the receiving coil. The simulation results for the magnetic field distributions and the time-domain current waveforms agree very well with the results of the theoretical analysis. This work thus provides a comprehensive understanding of the energy transfer mechanism involved in the magnetic resonant coupling system.

Signals of Opportunity Earth Reflectometry (SoOp-ER): Enabling new microwave observations from small satellites

NASA Astrophysics Data System (ADS)

Garrison, J. L.; Piepmeier, J. R.; Shah, R.; Lin, Y. C.; Du Toit, C. F.; Vega, M. A.; Knuble, J. J.

2016-12-01

Several recent experiments have demonstrated remote sensing by reutilizing communication satellite transmissions as sources in a bistatic radar configuration. This technique, referred to as "Signals of Opportunity Earth Reflectometry" (SoOp-ER), combines aspects of passive radiometry, active scatterometry and radar altimetry, but is essentially a new and alternative approach to microwave remote sensing. Reflectometry was first demonstrated with Global Navigation Satellite System (GNSS) signals, enabled by their use of pseudorandom noise (PRN) codes for ranging. Two decades of research in GNSS reflectometry has culminated in the upcoming launches of several satellite missions within the next few years (TechDemoSat-1, CYGNSS, and GEROS-ISS). GNSS signals, however, have low power and are confined to a few L-band frequencies allocated to radionavigation. Communication satellites, in contrast, transmit in nearly all bands penetrating the Earth's atmosphere at very high radiated powers to assure a low bit-error-rate. High transmission power and a forward scatter geometry result in a very high signal to noise ratio at the receiver. Surface resolution is determined by the signal bandwidth, not the antenna beam. In many applications, this will allow small, low gain antennas to be used to make scientifically useful measurements. These features indicate that SoOp-ER instruments would be an ideal technology for microwave remote sensing from small platforms. SoOp-ER observations are referenced at the specular point and a constellation of small satellites, evenly spaced in the same orbit, would provide global coverage through parallel specular point ground tracks. This presentation will summarize the current instrument development work by the authors on three different application of SoOp-ER: P-band (230-270 MHz) sensing of root-zone soil moisture (RZSM), S-band sensing of ocean winds and Ku/Ka-band altimetry. Potential mission scenarios using small satellite constellations using SoOp-ER at these frequencies are under study.

Optimal Time-Resource Allocation for Energy-Efficient Physical Activity Detection

PubMed Central

Thatte, Gautam; Li, Ming; Lee, Sangwon; Emken, B. Adar; Annavaram, Murali; Narayanan, Shrikanth; Spruijt-Metz, Donna; Mitra, Urbashi

2011-01-01

The optimal allocation of samples for physical activity detection in a wireless body area network for health-monitoring is considered. The number of biometric samples collected at the mobile device fusion center, from both device-internal and external Bluetooth heterogeneous sensors, is optimized to minimize the transmission power for a fixed number of samples, and to meet a performance requirement defined using the probability of misclassification between multiple hypotheses. A filter-based feature selection method determines an optimal feature set for classification, and a correlated Gaussian model is considered. Using experimental data from overweight adolescent subjects, it is found that allocating a greater proportion of samples to sensors which better discriminate between certain activity levels can result in either a lower probability of error or energy-savings ranging from 18% to 22%, in comparison to equal allocation of samples. The current activity of the subjects and the performance requirements do not significantly affect the optimal allocation, but employing personalized models results in improved energy-efficiency. As the number of samples is an integer, an exhaustive search to determine the optimal allocation is typical, but computationally expensive. To this end, an alternate, continuous-valued vector optimization is derived which yields approximately optimal allocations and can be implemented on the mobile fusion center due to its significantly lower complexity. PMID:21796237

Wireless power transmission using ultrasonic guided waves

NASA Astrophysics Data System (ADS)

Kural, A.; Pullin, R.; Featherston, C.; Paget, C.; Holford, K.

2011-07-01

The unavailability of suitable power supply at desired locations is currently an important obstacle in the development of distributed, wireless sensor networks for applications such as structural health monitoring of aircraft. Proposed solutions range from improved batteries to energy harvesting from vibration, temperature gradients and other sources. A novel approach is being investigated at Cardiff University School of Engineering in cooperation with Airbus. It aims to utilise ultrasonic guided Lamb waves to transmit energy through the aircraft skin. A vibration generator is to be placed in a location where electricity supply is readily available. Ultrasonic waves generated by this device will travel through the aircraft structure to a receiver in a remote wireless sensor node. The receiver will convert the mechanical vibration of the ultrasonic waves back to electricity, which will be used to power the sensor node. This paper describes the measurement and modelling of the interference pattern which emerges when Lamb waves are transmitted continuously as in this power transmission application. The discovered features of the pattern, such as a large signal amplitude variation and a relatively high frequency, are presented and their importance for the development of a power transmission system is discussed.

Magnetic susceptibility well-logging unit with single power supply thermoregulation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seeley, R. L.

1985-11-05

The magnetic susceptibility well-logging unit with single power supply thermoregulation system provides power from a single surface power supply over a well-logging cable to an integrated circuit voltage regulator system downhole. This voltage regulator system supplies regulated voltages to a temperature control system and also to a Maxwell bridge sensing unit which includes the solenoid of a magnetic susceptibility probe. The temperature control system is provided with power from the voltage regulator system and operates to permit one of several predetermined temperatures to be chosen, and then operates to maintain the solenoid of a magnetic susceptibility probe at this chosenmore » temperature. The temperature control system responds to a temperature sensor mounted upon the probe solenoid to cause resistance heaters concentrically spaced from the probe solenoid to maintain the chosen temperature. A second temperature sensor on the probe solenoid provides a temperature signal to a temperature transmitting unit, which initially converts the sensed temperature to a representative voltage. This voltage is then converted to a representative current signal which is transmitted by current telemetry over the well logging cable to a surface electronic unit which then reconverts the current signal to a voltage signal.« less

Computationally Efficient Power Allocation Algorithm in Multicarrier-Based Cognitive Radio Networks: OFDM and FBMC Systems

NASA Astrophysics Data System (ADS)

Shaat, Musbah; Bader, Faouzi

2010-12-01

Cognitive Radio (CR) systems have been proposed to increase the spectrum utilization by opportunistically access the unused spectrum. Multicarrier communication systems are promising candidates for CR systems. Due to its high spectral efficiency, filter bank multicarrier (FBMC) can be considered as an alternative to conventional orthogonal frequency division multiplexing (OFDM) for transmission over the CR networks. This paper addresses the problem of resource allocation in multicarrier-based CR networks. The objective is to maximize the downlink capacity of the network under both total power and interference introduced to the primary users (PUs) constraints. The optimal solution has high computational complexity which makes it unsuitable for practical applications and hence a low complexity suboptimal solution is proposed. The proposed algorithm utilizes the spectrum holes in PUs bands as well as active PU bands. The performance of the proposed algorithm is investigated for OFDM and FBMC based CR systems. Simulation results illustrate that the proposed resource allocation algorithm with low computational complexity achieves near optimal performance and proves the efficiency of using FBMC in CR context.

A hybrid method for provincial scale energy-related carbon emission allocation in China.

PubMed

Bai, Hongtao; Zhang, Yingxuan; Wang, Huizhi; Huang, Yanying; Xu, He

2014-01-01

Achievement of carbon emission reduction targets proposed by national governments relies on provincial/state allocations. In this study, a hybrid method for provincial energy-related carbon emissions allocation in China was developed to provide a good balance between production- and consumption-based approaches. In this method, provincial energy-related carbon emissions are decomposed into direct emissions of local activities other than thermal power generation and indirect emissions as a result of electricity consumption. Based on the carbon reduction efficiency principle, the responsibility for embodied emissions of provincial product transactions is assigned entirely to the production area. The responsibility for carbon generation during the production of thermal power is borne by the electricity consumption area, which ensures that different regions with resource endowments have rational development space. Empirical studies were conducted to examine the hybrid method and three indices, per capita GDP, resource endowment index and the proportion of energy-intensive industries, were screened to preliminarily interpret the differences among China's regional carbon emissions. Uncertainty analysis and a discussion of this method are also provided herein.

75 FR 33220 - Unlicensed Personal Communications Services Devices in the 1920-1930 MHz Band

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... required minimum number of channels and transmit on the channels with the lowest power. According to DECT... interference to adjacent-band Advanced Wireless Service (AWS) and PCS services. 3. DECT claims that its... with the lowest power and an alternative approach suggested by DECT--could require affected systems to...

Energy Systems Integration News | Energy Systems Integration Facility |

Science.gov Websites

competition hosted by Google, IEEE Power Electronics Society, and NREL. Competing companies' inverters were electronics to operate at higher voltages and temperatures, allowing them to transmit more energy through a Power Electronics March 30 NREL has kicked off a new series of webinars on smart grid-related topics

47 CFR 24.238 - Emission limitations for Broadband PCS equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Broadband Personal Communications Service. (a) Out of band emissions. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. (b) Measurement procedure. Compliance with these rules is based on...

47 CFR 24.238 - Emission limitations for Broadband PCS equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Broadband Personal Communications Service. (a) Out of band emissions. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. (b) Measurement procedure. Compliance with these rules is based on...

47 CFR 24.238 - Emission limitations for Broadband PCS equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Broadband Personal Communications Service. (a) Out of band emissions. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. (b) Measurement procedure. Compliance with these rules is based on...

47 CFR 24.238 - Emission limitations for Broadband PCS equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Broadband Personal Communications Service. (a) Out of band emissions. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. (b) Measurement procedure. Compliance with these rules is based on...

47 CFR 22.565 - Transmitting power limits.

Code of Federal Regulations, 2011 CFR

2011-10-01

... channels listed in § 22.561 must not exceed the limits in this section. (a) Maximum ERP. The effective radiated power (ERP) of base and fixed transmitters must not exceed the applicable limits in this paragraph under any circumstances. Frequency range (MHz) Maximum ERP (watts) 152-153 1400 157-159 150 454-455 3500...

47 CFR 22.565 - Transmitting power limits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... channels listed in § 22.561 must not exceed the limits in this section. (a) Maximum ERP. The effective radiated power (ERP) of base and fixed transmitters must not exceed the applicable limits in this paragraph under any circumstances. Frequency range (MHz) Maximum ERP (watts) 152-153 1400 157-159 150 454-455 3500...

75 FR 30057 - Proposed Issuance of an Incidental Take Permit to Energy Northwest for Construction and Operation...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... consist of up to 32 wind turbines with a generating capacity of 82 megawatts (MW) of electricity. Power generated by the wind turbines would be transmitted to the existing Bonneville Power Administration... conjunction with the construction, operation, maintenance, and decommissioning of the Radar Ridge Wind Project...

47 CFR 15.319 - General technical requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... full bandwidth of the channel. (d) Power spectral density shall not exceed 3 milliwatts in any 3 kHz bandwidth as measured with a spectrum analyzer having a resolution bandwidth of 3 kHz. (e) The peak transmit power shall be reduced by the amount in decibels that the maximum directional gain of the antenna...

47 CFR 15.319 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... full bandwidth of the channel. (d) Power spectral density shall not exceed 3 milliwatts in any 3 kHz bandwidth as measured with a spectrum analyzer having a resolution bandwidth of 3 kHz. (e) The peak transmit power shall be reduced by the amount in decibels that the maximum directional gain of the antenna...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jia, Zhiwei, E-mail: jiayege@hotmail.com; Yan, Guozheng; Zhu, Bingquan

An implanted telemetry system for experimental animals with or without anaesthesia can be used to continuously monitor physiological parameters. This system is significant not only in the study of organisms but also in the evaluation of drug efficacy, artificial organs, and auxiliary devices. The system is composed of a miniature electronic capsule, a wireless power transmission module, a data-recording device, and a processing module. An electrocardiograph, a temperature sensor, and a pressure sensor are integrated in the miniature electronic capsule, in which the signals are transmitted in vitro by wireless communication after filtering, amplification, and A/D sampling. To overcome themore » power shortage of batteries, a wireless power transmission module based on electromagnetic induction was designed. The transmitting coil of a rectangular-section solenoid and a 3D receiving coil are proposed according to stability and safety constraints. Experiments show that at least 150 mW of power could pick up on the load in a volume of Φ10.5 mm × 11 mm, with a transmission efficiency of 2.56%. Vivisection experiments verified the feasibility of the integrated radio-telemetry system.« less

Imaging Arrays With Improved Transmit Power Capability

PubMed Central

Zipparo, Michael J.; Bing, Kristin F.; Nightingale, Kathy R.

2010-01-01

Bonded multilayer ceramics and composites incorporating low-loss piezoceramics have been applied to arrays for ultrasound imaging to improve acoustic transmit power levels and to reduce internal heating. Commercially available hard PZT from multiple vendors has been characterized for microstructure, ability to be processed, and electroacoustic properties. Multilayers using the best materials demonstrate the tradeoffs compared with the softer PZT5-H typically used for imaging arrays. Three-layer PZT4 composites exhibit an effective dielectric constant that is three times that of single layer PZT5H, a 50% higher mechanical Q, a 30% lower acoustic impedance, and only a 10% lower coupling coefficient. Application of low-loss multilayers to linear phased and large curved arrays results in equivalent or better element performance. A 3-layer PZT4 composite array achieved the same transmit intensity at 40% lower transmit voltage and with a 35% lower face temperature increase than the PZT-5 control. Although B-mode images show similar quality, acoustic radiation force impulse (ARFI) images show increased displacement for a given drive voltage. An increased failure rate for the multilayers following extended operation indicates that further development of the bond process will be necessary. In conclusion, bonded multilayer ceramics and composites allow additional design freedom to optimize arrays and improve the overall performance for increased acoustic output while maintaining image quality. PMID:20875996

Infrared system for monitoring movement of objects

DOEpatents

Valentine, Kenneth H.; Falter, Diedre D.; Falter, Kelly G.

1991-01-01

A system for monitoring moving objects, such as the flight of honeybees and other insects, using a pulsed laser light source. This system has a self-powered micro-miniaturized transmitting unit powered, in the preferred embodiment, with an array solar cells. This transmitting unit is attached to the object to be monitored. These solar cells provide current to a storage energy capacitor to produce, for example, five volts for the operation of the transmitter. In the simplest embodiment, the voltage on the capacitor operates a pulse generator to provide a pulsed energizing signal to one or more very small laser diodes. The pulsed light is then received at a receiving base station using substantially standard means which converts the light to an electrical signal for processing in a microprocessor to create the information as to the movement of the object. In the case of a unit for monitoring honeybees and other insects, the transmitting unit weighs less than 50 mg, and has a size no larger than 1.times.3.times.5 millimeters. Also, the preferred embodiment provides for the coding of the light to uniquely identify the particular transmitting unit that is being monitored. A "wake-up" circuit is provided in the preferred embodiment whereby there is no transmission until the voltage on the capacitor has exceeded a pre-set threshold. Various other uses of the motion-detection system are described.

Infrared system for monitoring movement of objects

DOEpatents

Valentine, K.H.; Falter, D.D.; Falter, K.G.

1991-04-30

A system is described for monitoring moving objects, such as the flight of honeybees and other insects, using a pulsed laser light source. This system has a self-powered micro-miniaturized transmitting unit powered, in the preferred embodiment, with an array of solar cells. This transmitting unit is attached to the object to be monitored. These solar cells provide current to a storage energy capacitor to produce, for example, five volts for the operation of the transmitter. In the simplest embodiment, the voltage on the capacitor operates a pulse generator to provide a pulsed energizing signal to one or more very small laser diodes. The pulsed light is then received at a receiving base station using substantially standard means which converts the light to an electrical signal for processing in a microprocessor to create the information as to the movement of the object. In the case of a unit for monitoring honeybees and other insects, the transmitting unit weighs less than 50 mg, and has a size no larger than 1[times]3[times]5 millimeters. Also, the preferred embodiment provides for the coding of the light to uniquely identify the particular transmitting unit that is being monitored. A wake-up' circuit is provided in the preferred embodiment whereby there is no transmission until the voltage on the capacitor has exceeded a pre-set threshold. Various other uses of the motion-detection system are described. 4 figures.

Study on the optimization allocation of wind-solar in power system based on multi-region production simulation

NASA Astrophysics Data System (ADS)

Xu, Zhicheng; Yuan, Bo; Zhang, Fuqiang

2018-06-01

In this paper, a power supply optimization model is proposed. The model takes the minimum fossil energy consumption as the target, considering the output characteristics of the conventional power supply and the renewable power supply. The optimal capacity ratio of wind-solar in the power supply under various constraints is calculated, and the interrelation between conventional power supply and renewable energy is analyzed in the system of high proportion renewable energy integration. Using the model, we can provide scientific guidance for the coordinated and orderly development of renewable energy and conventional power sources.

On Proper Selection of Multihop Relays for Future Enhancement of AeroMACS Networks

NASA Technical Reports Server (NTRS)

Kamali, Behnam; Kerczewski, Robert J.; Apaza, Rafael D.

2015-01-01

As the Aeronautical Mobile Airport Communications System (AeroMACS) has evolved from a technology concept to a deployed communications network over major US airports, it is now time to contemplate whether the existing capacity of AeroMACS is sufficient to meet the demands set forth by all fixed and mobile applications over the airport surface given the AeroMACS constraints regarding bandwidth and transmit power. The underlying idea in this article is to present IEEE 802.16j-based WiMAX as a technology that can address future capacity enhancements and therefore is most feasible for AeroMACS applications. The principal argument in favor IEEE 802.16j technology is the flexible and cost effective extension of radio coverage that is afforded by relay fortified networks, with virtually no increase in the power requirements and virtually no rise in interference levels to co-allocated applications. The IEEE 802.16j-based multihop relay systems are briefly described. The focus is on key features of this technology, frame structure, and its architecture. Next, AeroMACS is described as a WiMAX-based wireless network. The two major relay modes supported by IEEE 802.16j amendment, i.e., transparent and non-transparent are described. The benefits of employing multihop relays are listed. Some key challenges related to incorporating relays into AeroMACS networks are discussed. The selection of relay type in a broadband wireless network affects a number of network parameters such as latency, signal overhead, PHY (Scalable Physical Layer) and MAC (Media Access Layer) layer protocols, consequently it can alter key network quantities of throughput and QoS (Quality of Service).