On the Use of a Molten Salt Fast Reactor to Apply an Idealized Transmutation Scenario for the Nuclear Phase Out

PubMed Central

Merk, Bruno; Rohde, Ulrich; Glivici-Cotruţă, Varvara; Litskevich, Dzianis; Scholl, Susanne

2014-01-01

In the view of transmutation of transuranium (TRU) elements, molten salt fast reactors (MSFRs) offer certain advantages compared to solid fuelled reactor types like sodium cooled fast reactors (SFRs). In the first part these advantages are discussed in comparison with the SFR technology, and the research challenges are analyzed. In the second part cycle studies for the MSFR are given for different configurations – a core with U-238 fertile, a fertile free core, and a core with Th-232 as fertile material. For all cases, the transmutation potential is determined and efficient transmutation performance for the case with thorium as a fertile material as well as for the fertile free case is demonstrated and the individual advantages are discussed. The time evolution of different important isotopes is analyzed. In the third part a strategy for the optimization of the transmutation efficiency is developed. The final aim is dictated by the phase out decision of the German government, which requests to put the focus on the determination of the maximal transmutation efficiency and on an as much as possible reduced leftover of transuranium elements at the end of the reactor life. This minimal leftover is achieved by a two step procedure of a first transmuter operation phase followed by a second deep burning phase. There the U-233, which is bred in the blanket of the core consisting of thorium containing salt, is used as feed. It is demonstrated, that transmutation rates up to more than 90% can be achieved for all transuranium isotopes, while the production of undesired high elements like californium is very limited. Additionally, the adaptations needed for the simulation of a MSFR, and the used tool HELIOS 1.10 is described. PMID:24690768

[Trans-uranium elements in food products (review)].

PubMed

Vasilenko, I Ia

1994-01-01

The data of Russian and foreign authors concerning of level environmental contamination and migration of transuranic elements in food chains, metabolism and biological danger of nuclides entering in human body with foods are reviewed. A level of radionuclide load of population and doses of radiation are discussed and the danger is estimated. The doses of radiation from radionuclide ingestion are lower than level of allowed radiation safety standards.

History of MET Lab Section C-I, April 1942--April 1943

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seaborg, G.T.

A day-to-day account of the work done at the University of Chicago Metallurgical Laboratory from April 1942 to April 1943 is given. The work concerned the development of chemical procedures for the extraction of plutonium, for the purification of plutonium, and, in the later phases, for research on the isotopes of other heavy elements including other transuranium elements. (LK)

Implications of human tissue studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.

1986-10-01

Through radiochemical analysis of voluntary tissue donations, the United States Transuranium and Uranium Registries are gaining improved understanding of the distribution and biokinetics of actinide elements in occupationally exposed persons. Evaluation of the first two whole body contributions to the Transuranium Registry revealed an inverse proportionality between actinide concentration and bone ash fraction. The analysis of a whole body with a documented /sup 241/Am deposition indicated a significantly shorter half-time in liver and a greater fraction resident in the skeleton than predicted by existing models. Other studies of the Registries are designed to evaluate in vivo estimates of actinide depositionmore » with those derived from postmortem tissue analysis, compare results of animal experiments with human data, and reviw histopathologic slides for tissue toxicity that might be attributable to exposure to uranium and the transuranic elements. The implications of these recent findings and other work of the Registries are discussed from the standpoint of their potential impact on biokinetic modeling, internal dose assessment, safety standards, and operational health physics practices.« less

United States transuranium and uranium registries - 25 years of growth, research, and service. Annual report, April 1992--September 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.; Harwick, L.A.; Toohey, R.E.

The Registries originated in 1968 as the National Plutonium Registry with the name changed to the United States Transuranium Registry the following year to reflect a broader concern with the heavier actinides as well. Initially, the scientific effort of the USTR was directed towards study of the distribution and dose of plutonium and americium in occupationally exposed persons, and to assessment of the effects of exposure to the transuranium elements on health. This latter role was reassessed during the 1970`s when it was recognized that the biased cohort of the USTR was inappropriate for epidemiologic analysis. In 1978, the administrativelymore » separate but parallel United States Uranium Registry was created to carry out similar work among persons exposed to uranium and its decay products. A seven member scientific advisory committee provided guidance and scientific oversight. In 1992, the two Registries were administratively combined and transferred from the purview of a Department of Energy contractor to Washington State University under the provisions of a grant. Scientific results for the first twenty-five years of the Registries are summarized, including the 1985 publication of the analysis of the first whole body donor. Current scientific work in progress is summarized along with administrative activities for the period.« less

Organometallic neptunium(III) complexes.

PubMed

Dutkiewicz, Michał S; Farnaby, Joy H; Apostolidis, Christos; Colineau, Eric; Walter, Olaf; Magnani, Nicola; Gardiner, Michael G; Love, Jason B; Kaltsoyannis, Nikolas; Caciuffo, Roberto; Arnold, Polly L

2016-08-01

Studies of transuranic organometallic complexes provide a particularly valuable insight into covalent contributions to the metal-ligand bonding, in which the subtle differences between the transuranium actinide ions and their lighter lanthanide counterparts are of fundamental importance for the effective remediation of nuclear waste. Unlike the organometallic chemistry of uranium, which has focused strongly on U(III) and has seen some spectacular advances, that of the transuranics is significantly technically more challenging and has remained dormant. In the case of neptunium, it is limited mainly to Np(IV). Here we report the synthesis of three new Np(III) organometallic compounds and the characterization of their molecular and electronic structures. These studies suggest that Np(III) complexes could act as single-molecule magnets, and that the lower oxidation state of Np(II) is chemically accessible. In comparison with lanthanide analogues, significant d- and f-electron contributions to key Np(III) orbitals are observed, which shows that fundamental neptunium organometallic chemistry can provide new insights into the behaviour of f-elements.

Organometallic neptunium(III) complexes

NASA Astrophysics Data System (ADS)

Dutkiewicz, Michał S.; Farnaby, Joy H.; Apostolidis, Christos; Colineau, Eric; Walter, Olaf; Magnani, Nicola; Gardiner, Michael G.; Love, Jason B.; Kaltsoyannis, Nikolas; Caciuffo, Roberto; Arnold, Polly L.

2016-08-01

Studies of transuranic organometallic complexes provide a particularly valuable insight into covalent contributions to the metal-ligand bonding, in which the subtle differences between the transuranium actinide ions and their lighter lanthanide counterparts are of fundamental importance for the effective remediation of nuclear waste. Unlike the organometallic chemistry of uranium, which has focused strongly on UIII and has seen some spectacular advances, that of the transuranics is significantly technically more challenging and has remained dormant. In the case of neptunium, it is limited mainly to NpIV. Here we report the synthesis of three new NpIII organometallic compounds and the characterization of their molecular and electronic structures. These studies suggest that NpIII complexes could act as single-molecule magnets, and that the lower oxidation state of NpII is chemically accessible. In comparison with lanthanide analogues, significant d- and f-electron contributions to key NpIII orbitals are observed, which shows that fundamental neptunium organometallic chemistry can provide new insights into the behaviour of f-elements.

Annual report of the United States transuranium and uranium registries, October 1, 1988--September 30, 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.; Swint, M.J.; Dietert, S.E.

1990-04-01

This report summarizes the primary scientific activities of the United States Transuranium and Uranium Registries for the period October 1, 1988 through September 30, 1989. The Registries are parallel human tissue research programs devoted to the study of the actinide elements in man. The emphasis of the Transuranium Registry was directed toward evaluation of six whole body donations. In the five cases whose exposure was through inhalation, approximately half of the total body content of Pu-239 + 240 and a third of the Am-241 was found in the respiratory tract, suggesting that these nuclides are more avidly retained than predictedmore » by the current model of the International Commission on Radiological Protection. A significant fraction of these nuclides is found in soft tissues other than liver, and an uptake fraction of 0.2 is proposed for muscle, with a residence half-time of 10 years. Studies of these and routine autopsy cases indicate that more than 90% of the total respiratory tract plutonium or americium is in the lungs, with the remainder in the lymph nodes, and that a greater fraction is found in the lungs of smokers relative to the lymph nodes. Primary activities of the Uranium Registry centered around the acquisition of a whole body donation from a woman who had received an injection of colloidal thorium dioxide some 38 years prior to death.« less

Californium

NASA Astrophysics Data System (ADS)

Haire, Richard G.

The discovery of californium came in the era of the syntheses and identifications of other transplutonium elements, following the end of World War II. The discovery of the element californium, like many of the other actinide elements, hinged on the development of new experimental techniques in conjunction with predictions based on nuclear systematics. Californium was named after the University and State of California where many of the transuranium elements were first identified. This element was discovered by Thompson, Street, Ghiorso, and Seaborg (Hyde et al., 1971; Seaborg and Loveland, 1990) in February, 1950. The discovery of californium came only 2 months after the preparation and identification of the first isotope of berkelium, element 97 (see Chapter 10). An account of the discovery and reminiscences about the early work on californium has been given by Ghiorso (1983).

Magnetic measurements of the transuranium elements. Progress report, January 1, 1984-December 31, 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huray, P.G.; Nave, S.E.

1984-01-01

Measurements of the magnetic properties of dhcp californium-249 metal indicated the presence of three regions of differing magnetic character. Additional measurements are also reported. Magnetic moments and valence states of terbium in TbF/sub 3/, BaTbO/sub 3/, and TbO/sub 1/ /sub 8/ are discussed. Progress on high-field operation of the micro-magnetic susceptometer is reported.

The development of fuel performance models at the European institute for transuranium elements

NASA Astrophysics Data System (ADS)

Lassmann, K.; Ronchi, C.; Small, G. J.

1989-07-01

The design and operational performance of fuel rods for nuclear power stations has been the subject of detailed experimental research for over thirty years. In the last two decades the continuous demands for greater economy in conjunction with more stringent safety criteria have led to an increasing reliance on computer simulations. Conditions within a fuel rod must be calculated both for normal operation and for proposed reactor faults. It has thus been necessary to build up a reliable, theoretical understanding of the intricate physical, mechanical and chemical processes occurring under a wide range of conditions to obtain a quantitative insight into the behaviour of the fuel. A prime requirement, which has also proved to be the most taxing, is to predict the conditions under which failure of the cladding might occur, particularly in fuel nearing the end of its useful life. In this paper the general requirements of a fuel performance code are discussed briefly and an account is given of the basic concepts of code construction. An overview is then given of recent progress at the European Institute for Transuranium Elements in the development of a fuel rod performance code for general application and of more detailed mechanistic models for fission product behaviour.

Experimental thermochemistry of neptunium oxides: Np2O5 and NpO2

NASA Astrophysics Data System (ADS)

Zhang, Lei; Dzik, Ewa A.; Sigmon, Ginger E.; Szymanowski, Jennifer E. S.; Navrotsky, Alexandra; Burns, Peter C.

2018-04-01

Neptunium (Np) compounds are important in the nuclear fuel cycle because of the buildup and long half-life (2.14 Ma) of Np-237 in nuclear waste, especially during long-term disposal in a geological repository. Neptunium in environmental conditions exists mainly in two oxidation states (+5 and + 4) and can substitute for uranium and/or rare earths in solid phases. Yet thermochemical data for solid neptunium compounds are scarce, despite being critical for evaluating the environmental transport of this radioactive and toxic element. Although high temperature oxide melt solution calorimetry has proven very useful in obtaining thermodynamic data for the formation of uranium and thorium oxide materials, it has not yet been applied to transuranium compounds. Continuing a program at Notre Dame to study the thermodynamics of transuranium compounds, we report the first determination of the enthalpies of drop solution of well-characterized neptunium oxides (Np2O5 and NpO2) using oxide melt solution calorimetry in molten sodium molybdate solvent at 973 K. The enthalpy of the decomposition reaction, Np2O5(cr) = 2NpO2(cr) + 1/2O2(g) at 298 K, is determined to be 7.70 ± 5.86 kJ/mol, and this direct measurement is consistent with existing thermodynamic data. The calorimetric methodology is straightforward and produces reliable data using milligram quantities of radioactive materials, and can be applied to many other transuranium compounds.

Almost twenty years' search of transuranium isotopes in effluents discharged to air from nuclear power plants with VVER reactors.

PubMed

Hölgye, Z; Filgas, R

2006-04-01

Airborne effluents of 5 stacks (stacks 1-5) of three nuclear power plants, with 9 pressurized water reactors VVER of 4,520 MWe total power, were searched for transuranium isotopes in different time periods. The search started in 1985. The subject of this work is a presentation of discharge data for the period of 1998-2003 and a final evaluation. It was found that 238Pu, 239,240Pu, 241Am, 242Cm, and 244Cm can be present in airborne effluents. Transuranium isotope contents in most of the quarterly effluent samples from stacks 2, 4 and 5 were not measurable. Transuranium isotopes were present in the effluents from stack l during all 9 years of the study and from stack 3 since the 3rd quarter of 1996 as a result of a defect in the fuel cladding. A relatively high increase of transuranium isotopes in effluents from stack 3 occurred in the 3rd quarter of 1999, and a smaller increase occurred in the 3rd quarter of 2003. In each instance 242Cm prevailed in the transuranium isotope mixtures. 238Pu/239,240Pu, 241Am/239,240Pu, 242Cm/239,240Pu, and 244Cm/239,240Pu ratios in fuel for different burn-up were calculated, and comparison of these ratios in fuel and effluents was performed.

United States Transuranium and Uranium Registries. Annual report February 1, 2001--January 31, 2002

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehrhart, Susan M.; Filipy, Ronald E.

2002-07-01

This report documents the activities of the United States Transuranium and Uranium Registries (USTUR) from February 2001 through January 2002. Progress in continuing collaborations and several new collaborations is reviewed.

Chemistry Division: Annual progress report for period ending March 31, 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-08-01

This report is divided into the following sections: coal chemistry; aqueous chemistry at high temperatures and pressures; geochemistry of crustal processes to high temperatures and pressures; chemistry of advanced inorganic materials; structure and dynamics of advanced polymeric materials; chemistry of transuranium elements and compounds; separations chemistry; reactions and catalysis in molten salts; surface science related to heterogeneous catalysis; electron spectroscopy; chemistry related to nuclear waste disposal; computational modeling of security document printing; and special topics. (DLC)

Challenges in the quality assurance of elemental and isotopic analyses in the nuclear domain benefitting from high resolution ICP-OES and sector field ICP-MS.

PubMed

Krachler, Michael; Alvarez-Sarandes, Rafael; Van Winckel, Stefaan

Accurate analytical data reinforces fundamentally the meaningfulness of nuclear fuel performance assessments and nuclear waste characterization. Regularly lacking matrix-matched certified reference materials, quality assurance of elemental and isotopic analysis of nuclear materials remains a challenging endeavour. In this context, this review highlights various dedicated experimental approaches envisaged at the European Commission-Joint Research Centre-Institute for Transuranium Elements to overcome this limitation, mainly focussing on the use of high resolution-inductively coupled plasma-optical emission spectrometry (HR-ICP-OES) and sector field-inductively coupled plasma-mass spectrometry (SF-ICP-MS). However, also α- and γ-spectrometry are included here to help characterise extensively the investigated actinide solutions for their actual concentration, potential impurities and isotopic purity.

Evidence for the remobilisation of transuranic elements in the terrestrial environment.

PubMed

Hursthouse, A S; Livens, F R

1993-09-01

The transuranium elements, Np, Pu and Am discharged from the BNFL fuel reprocessing plant at Sellafield have accumulated in the local environment. The processes responsible for their dispersal rely both on physical transportation and their chemical reactivity. The transuranics have a complex chemistry, with multiple oxidation states and a strongly polarising character. In the environment, the particle active III/IV and more mobile VNI oxidation state groups are important and govern their geochemical behaviour and subsequent dispersal.Studies of the behaviour of the transuranics, particularly Pu, in the Irish Sea, have shown that the majority of the radionuclides in the liquid effluent discharged from Sellafield, quickly becomes associated with the marine sediments. Their dispersal and distribution in the environment is then governed primarily by the movement of particulate material and for some sites it has been suggested that sediment profiles preserve the historical record of discharges from the plant.In tidally inundated soils, radionuclide levels are greatly enhanced. These soils are water-logged for long periods of the year, are strongly anoxic and accretion rate are very low. The distribution of Np, Pu and Am in the soil suggests that simple sedimentary accumulation mechanism cannot provide an adequate explanation for the profiles observed. From preliminary studies of soil pore water composition and detailed analysis of the variation of isotopic ratios in the soil cores, it is apparent that a small but significant component of the radionuclide inventory is mobile. In addition, it is clear that the mechanisms responsible for this mobility allows differentiation between the transuranium nuclides.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobart, David E.

In celebrating the centennial anniversary of the birth of Glenn T. Seaborg it is fitting that we recount and pay tribute to his legacy. Many know of the scientific accomplishments of this man who became a legend and anyone who has attended his lectures can attest to how informative, educational, and entertaining he was. He had a beguiling and whimsical sense of humor and used this to drive home his points and share his passion and quest for discovery. The periodic table is a fundamental cornerstone of science and remains a central unifying principal. Seaborg was the architect of themore » actinide series of elements and their proper placement in the periodic table and co-discoverer of ten transuranium elements - one of which bears his name, element 106, seaborgium. The work and achievements of this Nobel laureate have touched the lives of many and his legacy will continue for generations to come.« less

Chemistry Division annual progress report for period ending April 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poutsma, M.L.; Ferris, L.M.; Mesmer, R.E.

1993-08-01

The Chemistry Division conducts basic and applied chemical research on projects important to DOE`s missions in sciences, energy technologies, advanced materials, and waste management/environmental restoration; it also conducts complementary research for other sponsors. The research are arranged according to: coal chemistry, aqueous chemistry at high temperatures and pressures, geochemistry, chemistry of advanced inorganic materials, structure and dynamics of advanced polymeric materials, chemistry of transuranium elements and compounds, chemical and structural principles in solvent extraction, surface science related to heterogeneous catalysis, photolytic transformations of hazardous organics, DNA sequencing and mapping, and special topics.

United States Transuranium and Uranium Registries. Annuary report, February 1, 2004 - June 30, 2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alldredge, J. Richard; Ehrhart, Susan M.; Eliston, James T.

2006-05-31

Three events of significance to the U. S. Transuranium and Uranium Registries (USTUR) occurred during this reporting period: 1. The search for a new Associate Director was successful in that Dr. Anthony C. (Tony) James was appointed to the position, 2. A five-year grant for the operation of the USTUR was approved by the U. S. Department of Energy; the previous grant cycles were for three years, 3. I retired from the USTUR Directorship on July 1, 2005 and Tony James became the new Director.

A Guide to the Elements, Rev. Edition (by Albert Stwertka)

NASA Astrophysics Data System (ADS)

Berger, Reviewed By Daniel

1999-12-01

This edition is identical in format and content to the 1996 edition, now sold as the "library edition", except that the names and information for elements 104-109 have been updated. My earlier review still applies; a page-by-page comparison found this edition identical to the first except as noted in the previous sentence. The major revision has been in size and price. The 50% price reduction is welcome, but the format was not changed when the size was reduced, and the resulting 9-point font puts readers at risk of eyestrain. I would like to correct one of the criticisms in my earlier review There is excellent discussion of the industrial uses of each element, as well as its most common source minerals. The more economically important elements are given extensive discussions, detailing industrial uses of the element and its compounds. However, biological activity is given spotty coverage. There is no mention - under "iron" or elsewhere - of the central biological role of iron in oxygen transport or of magnesium in photosynthesis. When coverage appears it is not bad: the roles of calcium in vertebrate and invertebrate skeletons, of fluorine in reducing tooth decay by changing hydroxyapatite to fluorapatite, and of cobalt in vitamin B12 are discussed. While information on transuranium elements has been updated, there has been no attempt to correct several minor errors in spelling, placement, or even information. On page 14 the 1s subshell appears as part of the L (n = 2) shell, and upon the electrolysis of molten sodium chloride on page 54, "sodium collects atthe cathode, and chloride [sic] at...the anode." On page 73 the etymology of "potash" is still given as "potassium-rich ash" rather than "ash burned down in pots", though it is obvious that the latter is intended. On page 74, a picture caption claims that black powder ("potassium nitrate, wood charcoal, and sulfur") is used in modern, high-powered rifle cartridges. In spite of the mistakes, which are relatively few, there is much good information in this book. The essential chemical properties of each element are detailed so that periodic trends may be easily seen; important industrial uses are presented in some detail; transuranium elements and radioisotopes are given careful coverage; and biological activity is (occasionally) discussed. The presentation is interesting and eye-catching, designed to hold the interest of a student who knows little about chemistry. And now, the price has been made more reasonable. While the hardcover edition remains $35.00, the paperback edition, at half price, should bring this useful book into wider use.

[Carcinogenic efficacy of the transuranium elements americium-241 and curium-244].

PubMed

Rudnitskaia, E I

1984-01-01

Albino female rats were used in the experiments. After a single intraperitoneal administration of 241Am and 244Cm chloride is doses ranging from 0.37 to 185 kBq/kg (14 doses were used) it was established that the doses applied had different effect on the average life of animals. The largest doses shortened and the lowest increased the life span of experimental animals as compared to the controls. The carcinogenic effect of the studied radionuclides and the development of malignant tumors were detected at sufficiently low doses absorbed. Malignant tumors developed in the experimental and control animals were different not only in their incidence but also their localization and spectrum.

Einsteinium

NASA Astrophysics Data System (ADS)

Haire, Richard G.

The discovery of einsteinium, element 99, came about during the analyses of nuclear products produced in and then recovered from test debris following a thermonuclear explosion (weapon test device, ‘Mike', November 1952) at Eniwetok Atoll in the Pacific Ocean. The uranium present in this device was subjected to a very intense neutron flux (integrated fluence of about 1024neutrons) in an extremely short time frame (few nanoseconds), which allowed a large number of multiple neutron captures with a minimal degree of decay of the products formed. Nuclei were formed with usually high neutron/proton ratios (very ‘heavy' uranium isotopes), which then rapidly beta-decayed into new, transuranium isotopes through element 100. Scientists from several U.S. Government laboratories separated and analyzed extensively the debris samplings in the following weeks. From these investigations came the discovery and identification of einsteinium and fermium. The first element was named in honor of Albert Einstein, and assigned the symbol, E (later changed to the current symbol, Es). Additional details and discussions about the discovery of this element and the scientists involved are given in several references (Thompson et al., 1954; Ghiorso et al., 1955; Fields et al., 1956; Hyde et al., 1964; Seaborg and Loveland, 1990).

Nuclear fuel in a reactor accident.

PubMed

Burns, Peter C; Ewing, Rodney C; Navrotsky, Alexandra

2012-03-09

Nuclear accidents that lead to melting of a reactor core create heterogeneous materials containing hundreds of radionuclides, many with short half-lives. The long-lived fission products and transuranium elements within damaged fuel remain a concern for millennia. Currently, accurate fundamental models for the prediction of release rates of radionuclides from fuel, especially in contact with water, after an accident remain limited. Relatively little is known about fuel corrosion and radionuclide release under the extreme chemical, radiation, and thermal conditions during and subsequent to a nuclear accident. We review the current understanding of nuclear fuel interactions with the environment, including studies over the relatively narrow range of geochemical, hydrological, and radiation environments relevant to geological repository performance, and discuss priorities for research needed to develop future predictive models.

Plutonium Story

DOE R&D Accomplishments Database

Seaborg, G. T.

1981-09-01

The first nuclear synthesis and identification (i.e., the discovery) of the synthetic transuranium element plutonium (isotope /sup 238/Pu) and the demonstration of its fissionability with slow neutrons (isotope /sup 239/Pu) took place at the University of California, Berkeley, through the use of the 60-inch and 37-inch cyclotrons, in late 1940 and early 1941. This led to the development of industrial scale methods in secret work centered at the University of Chicago's Metallurgical Laboratory and the application of these methods to industrial scale production, at manufacturing plants in Tennessee and Washington, during the World War II years 1942 to 1945. The chemical properties of plutonium, needed to devise the procedures for its industrial scale production, were studied by tracer and ultramicrochemical methods during this period on an extraordinarily urgent basis. This work, and subsequent investigations on a worldwide basis, have made the properties of plutonium very well known. Its well studied electronic structure and chemical properties give it a very interesting position in the actinide series of inner transition elements.

The Politics of Forgetting: Otto Hahn and the German Nuclear-Fission Project in World War II

NASA Astrophysics Data System (ADS)

Sime, Ruth Lewin

2012-03-01

As the co-discoverer of nuclear fission and director of the Kaiser Wilhelm Institute for Chemistry, Otto Hahn (1879-1968) took part in Germany`s nuclear-fission project throughout the Second World War. I outline Hahn's efforts to mobilize his institute for military-related research; his inclusion in high-level scientific structures of the military and the state; and his institute's research programs in neutron physics, isotope separation, transuranium elements, and fission products, all of potential military importance for a bomb or a reactor and almost all of it secret. These activities are contrasted with Hahn's deliberate misrepresentations after the war, when he claimed that his wartime work had been nothing but "purely scientific" fundamental research that was openly published and of no military relevance.

LECTURES ON PHYSICS, BIOPHYSICS, AND CHEMISTRY FOR HIGH SCHOOL SCIENCE TEACHERS GIVEN AT THE ERNEST O. LAWRENCE RADIATION LABORATORY, BERKELEY, CALIFORNIA, JUNE-AUGUST 1959

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calhoon, E.C.; Starring, P.W. eds.

1959-08-01

Lectures given at the Ernest 0. Lawrence Radiation Laboratory on physics, biophysics, and chemistry for high school science teachers are presented. Topics covered include a mathematics review, atomic physics, nuclear physics, solid-state physics, elementary particles, antiparticies, design of experiments, high-energy particle accelerators, survey of particle detectors, emulsion as a particle detector, counters used in high-energy physics, bubble chambers, computer programming, chromatography, the transuranium elements, health physics, photosynthesis, the chemistry and physics of virus, the biology of virus, lipoproteins and heart disease, origin and evolution of the solar system, the role of space satellites in gathering astronomical data, and radiation andmore » life in space. (M.C.G.)« less

Modeling The Skeleton Weight of an Adult Caucasian Man.

PubMed

Avtandilashvili, Maia; Tolmachev, Sergei Y

2018-05-17

The reference value for the skeleton weight of an adult male (10.5 kg) recommended by the International Commission on Radiological Protection in Publication 70 is based on weights of dissected skeletons from 44 individuals, including two U.S. Transuranium and Uranium Registries whole-body donors. The International Commission on Radiological Protection analysis of anatomical data from 31 individuals with known values of body height demonstrated significant correlation between skeleton weight and body height. The corresponding regression equation, Wskel (kg) = -10.7 + 0.119 × H (cm), published in International Commission on Radiological Protection Publication 70 is typically used to estimate the skeleton weight from body height. Currently, the U.S. Transuranium and Uranium Registries holds data on individual bone weights from a total of 40 male whole-body donors, which has provided a unique opportunity to update the International Commission on Radiological Protection skeleton weight vs. body height equation. The original International Commission on Radiological Protection Publication 70 and the new U.S. Transuranium and Uranium Registries data were combined in a set of 69 data points representing a group of 33- to 95-y-old individuals with body heights and skeleton weights ranging from 155 to 188 cm and 6.5 to 13.4 kg, respectively. Data were fitted with a linear least-squares regression. A significant correlation between the two parameters was observed (r = 0.28), and an updated skeleton weight vs. body height equation was derived: Wskel (kg) = -6.5 + 0.093 × H (cm). In addition, a correlation of skeleton weight with multiple variables including body height, body weight, and age was evaluated using multiple regression analysis, and a corresponding fit equation was derived: Wskel (kg) = -0.25 + 0.046 × H (cm) + 0.036 × Wbody (kg) - 0.012 × A (y). These equations will be used to estimate skeleton weights and, ultimately, total skeletal actinide activities for biokinetic modeling of U.S. Transuranium and Uranium Registries partial-body donation cases.

Contribution of fission to heavy-element nucleosynthesis in an astrophysical r-process

NASA Astrophysics Data System (ADS)

Korneev, I. Yu.; Panov, I. V.

2011-12-01

During the formation of heavy elements in the neutron star merger (NSM) scenario with a fairly long duration of the r-process, most of the seed nuclei rapidly burn out at the initial stage. The nucleosynthesis wave rapidly reaches the region of actinoids, where beta-delayed, neutron-induced, and spontaneous fission are the main reaction channels. The fission products of transuranium elements are again drawn into the r-process as new seed nuclei to form the yields of elements with mass numbers A > 100. The contribution from the various types of fission to the formation of heavy and superheavy nuclei is investigated. The proposed r-process model applied to the NSM scenario describes well the observed abundances of chemical elements, which confirms the formation of the main r-process component in the NSM scenario. Simple extrapolations of the spontaneous fission half-lives are shown to be inapplicable for the region of nuclei with N ˜ 184, because the formulas do not reflect the increase in half-life when the shell structure changes as the number of neutrons approaches 184. The formation of superheavy elements in the r-process is possible, but their survival depends to a large extent on how reliable the predictions of nuclear parameters, including the half-lives of the forming nuclei from the island of long-lived isotopes, are. The contributions from various types of fission—neutron-induced, beta-delayed, and spontaneous one—to the formation of heavy elements in the main r-process have been determined.

Nuclear Data Sheets for A = 239

DOE PAGES

Browne, E.; Tuli, J. K.

2014-11-18

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=239. In general, a relatively small amount of new data on this mass chain has been reported since the previous evaluation in 2003. However, special evaluations, such as ''Database of prompt gamma rays from slow neutron–capture from elemental analysis'' (2007ChZX), have provided additional precise data for levels in 29U. Also, new Coulomb excitation measurements in 239Pu have extended the knowledge of the 1/2[631] rotational band up to Jπ=(55/2+)Jπ=(55/2+), and that of the octupole vibrational band up to Jπ=(53/2-)Jπ=(53/2-). Formore » historical knowledge it is worth mentioning the report on the “Discovery of isotopes of the transuranium elements with 93 <= Z <= 98'' (2013Fr02), where the information for elements Np, Pu, Am, and Cf with mass number A=239 is presented. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r 0) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Nuclear Data Sheets for A = 239

DOE Office of Scientific and Technical Information (OSTI.GOV)

Browne, E.; Tuli, J. K.

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=239. In general, a relatively small amount of new data on this mass chain has been reported since the previous evaluation in 2003. However, special evaluations, such as ''Database of prompt gamma rays from slow neutron–capture from elemental analysis'' (2007ChZX), have provided additional precise data for levels in 29U. Also, new Coulomb excitation measurements in 239Pu have extended the knowledge of the 1/2[631] rotational band up to Jπ=(55/2+)Jπ=(55/2+), and that of the octupole vibrational band up to Jπ=(53/2-)Jπ=(53/2-). Formore » historical knowledge it is worth mentioning the report on the “Discovery of isotopes of the transuranium elements with 93 <= Z <= 98'' (2013Fr02), where the information for elements Np, Pu, Am, and Cf with mass number A=239 is presented. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r 0) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Nuclear Data Sheets for A = 239

DOE Office of Scientific and Technical Information (OSTI.GOV)

Browne, E.; Tuli, J.K.

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=239. In general, a relatively small amount of new data on this mass chain has been reported since the previous evaluation in 2003. However, special evaluations, such as “Database of prompt gamma rays from slow neutron–capture from elemental analysis” (2007ChZX), have provided additional precise data for levels in {sup 239}U. Also, new Coulomb excitation measurements in {sup 239}Pu have extended the knowledge of the 1/2[631] rotational band up to Jπ=(55/2+), and that of the octupole vibrational band up tomore » Jπ=(53/2−). For historical knowledge it is worth mentioning the report on the “Discovery of isotopes of the transuranium elements with 93 <= Z <= 98” (2013Fr02), where the information for elements Np, Pu, Am, and Cf with mass number A=239 is presented. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r{sub 0}) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Determination of (236)U and transuranium elements in depleted uranium ammunition by alpha-spectrometry and ICP-MS.

PubMed

Desideri, D; Meli, M A; Roselli, C; Testa, C; Boulyga, S F; Becker, J S

2002-11-01

It is well known that ammunition containing depleted uranium (DU) was used by NATO during the Balkan conflict. To evaluate the origin of DU (the enrichment of natural uranium or the reprocessing of spent nuclear fuel) it is necessary to directly detect the presence of activation products ((236)U, (239)Pu, (240)Pu, (241)Am, and (237)Np) in the ammunition. In this work the analysis of actinides by alpha-spectrometry was compared with that by inductively coupled plasma mass spectrometry (ICP-MS) after selective separation of ultratraces of transuranium elements from the uranium matrix. (242)Pu and (243)Am were added to calculate the chemical yield. Plutonium was separated from uranium by extraction chromatography, using tri- n-octylamine (TNOA), with a decontamination factor higher than 10(6); after elution plutonium was determined by ICP-MS ((239)Pu and (240)Pu) and alpha-spectrometry ((239+240)Pu) after electroplating. The concentration of Pu in two DU penetrator samples was 7 x 10(-12) g g(-1) and 2 x 10(-11) g g(-1). The (240)Pu/(239)Pu isotope ratio in one penetrator sample (0.12+/-0.04) was significantly lower than the (240)Pu/(239)Pu ratios found in two soil samples from Kosovo (0.35+/-0.10 and 0.27+/-0.07). (241)Am was separated by extraction chromatography, using di(2-ethylhexyl)phosphoric acid (HDEHP), with a decontamination factor as high as 10(7). The concentration of (241)Am in the penetrator samples was 2.7 x 10(-14) g g(-1) and <9.4 x 10(-15) g g(-1). In addition (237)Np was detected at ultratrace levels. In general, ICP-MS and alpha-spectrometry results were in good agreement. The presence of anthropogenic radionuclides ((236)U, (239)Pu,(240)Pu, (241)Am, and (237)Np) in the penetrators indicates that at least part of the uranium originated from the reprocessing of nuclear fuel. Because the concentrations of radionuclides are very low, their radiotoxicological effect is negligible.

Validation of new superheavy elements and IUPAC-IUPAP joint working group

NASA Astrophysics Data System (ADS)

Jarlskog, Cecilia

2016-12-01

The great chemist Glenn Seaborg has written a delightful little book "Man-made Transuranium Elements", published in 1963, in which he points out that: "The former basic criterion for the discovery of a new element - namely, chemical identification and separation from all previously-known elements - had to be changed in the case of lawrencium (element 103). This also may be true for elements beyond lawrencium." Indeed this is what has happened. The elements with Z ≥ 103 are produced in nuclear reactions and are detected by counters. The detectors have undergone substantial refinement. For example one uses multiwire proportional chambers [for which George Charpak received the 1992 Nobel Prize in Physics] as well as solid state micro-strip detectors. In spite of this remarkable shift from chemistry to physics, the managerial staff of the International Union of Pure and Applied Chemistry (IUPAC) does not seem to be aware of what has been going on. The validation of superheavy elements should be done by physicists as the chemists lack the relevant competence as I will discuss here below. This article is about a collaboration between International Union of Pure and Applied Chemistry (IUPAC) and its sister organization International Union of Pure and Applied Physics (IUPAP), to deal with discovery of superheavy elements beyond Z = 112. I spent a great deal of time on this issue. In my opinion, the collaboration turned out to be a failure. For the sake of science, which should be our most important concern (and not politics), the rules for the future collaborations, if any, should be accurately defined and respected. The validation of new elements should be done by people who have the relevant competence - the physicists.

Electrochemical reduction of (U-40Pu-5Np)O 2 in molten LiCl electrolyte

NASA Astrophysics Data System (ADS)

Iizuka, Masatoshi; Sakamura, Yoshiharu; Inoue, Tadashi

2006-12-01

The electrochemical reduction of neptunium-containing MOX ((U-40Pu-5Np)O 2) was performed in molten lithium chloride melt at 923 K to investigate fundamental behavior of the transuranium elements and applicability of the method to reduction process for these materials. The Np-MOX was electrochemically reduced at the potential lower than -0.6 V vs. Bi-35 mol% Li reference electrode. The reduced metal grains in the surface region of the sample cohered with each other and made the layer of relatively high density, although it did not prevent the reduction of the sample toward the center. Complete reduction of the Np-MOX was shown by the weight change measurement through the electrochemical reduction and also by SEM-EDX observation. The chemical composition of the reduction products was homogeneous and agreed to that of the initial Np-MOX, which indicates that the reduction was completed and not selective among the actinides. The concentrations of the actinide elements, especially plutonium and americium in the electrolyte, increased with the progress of the tests, although their absolute values were very small. It is quite likely that plutonium and americium dissolve into the melt in the same manner as the lanthanide elements in the lithium reduction process.

Special Lecture in Memory of Glenn Theodore Seaborg (19 April 1912 - 25 February 1999) Glenn T. Seaborg's Multi-faceted Career

DOE R&D Accomplishments Database

Hoffman, Darleane C.

2001-11-01

Glenn Theodore Seaborg (1912-1999) was a world-renowned nuclear chemist, a Nobel Laureate in chemistry in 1951, co-discoverer of plutonium and nine other transuranium elements, Chairman of the US Atomic Energy Commission from 1961-71, scientific advisor to ten US presidents, active in national and international professional societies, an advocate for nuclear power as well as for a comprehensive nuclear test ban treaty, a prolific writer, an avid hiker, environmentalist, and sports enthusiast. He was known and esteemed not only by chemists and other scientists throughout the world, but also by lay people, politicians, statesmen, and students of all ages. This memorial includes a brief glimpse of Glenn Seaborg's early life and education, describes some of his major contributions to nuclear science over his long and fruitful career, and highlights his profound influence on nuclear science, both in the US and in the international community.

Implications of human tissue studies for radiation protection.

PubMed

Kathren, R L

1988-08-01

Through radiochemical analysis of voluntary tissue donations, the U.S. Transuranium and Uranium Registries (USTR) are gaining improved understanding of the distribution and biokinetics of actinide elements in occupationally exposed persons. Evaluation of the first two whole-body contributions to the USTR revealed an inverse proportionality between actinide concentration and bone ash. The analysis of a whole body with significant 241Am deposition indicated a significantly shorter half-time in liver and a greater fraction resident in the skeleton than predicted by existing models. Other studies with tissues obtained at autopsy suggest that existing biokinetic models for 238Pu and 241Am and the currently accepted models and limits on intake, which use these models as their basis, may be inaccurately implying that revisions of existing safety standards may be necessary. Other studies of the registries are designed to evaluate in-vivo estimates of actinide deposition with those derived from postmortem tissue analysis, to compare results of animal experiments with human data, and to review histopathologic slides for tissue changes that might be attributable to exposure to transuranic elements. The implications of these recent findings and other work of the registries is discussed from the standpoint of this potential effect on biokinetic modeling, internal dose assessment, and safety standards and operational health physics practices.

Implications of human tissue studies for radiation protection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.

1988-08-01

Through radiochemical analysis of voluntary tissue donations, the U.S. Transuranium and Uranium Registries (USTR) are gaining improved understanding of the distribution and biokinetics of actinide elements in occupationally exposed persons. Evaluation of the first two whole-body contributions to the USTR revealed an inverse proportionality between actinide concentration and bone ash. The analysis of a whole body with significant /sup 241/Am deposition indicated a significantly shorter half-time in liver and a greater fraction resident in the skeleton than predicted by existing models. Other studies with tissues obtained at autopsy suggest that existing biokinetic models for /sup 238/Pu and /sup 241/Am andmore » the currently accepted models and limits on intake, which use these models as their basis, may be inaccurately implying that revisions of existing safety standards may be necessary. Other studies of the registries are designed to evaluate in-vivo estimates of actinide deposition with those derived from postmortem tissue analysis, to compare results of animal experiments with human data, and to review histopathologic slides for tissue changes that might be attributable to exposure to transuranic elements. The implications of these recent findings and other work of the registries is discussed from the standpoint of this potential effect on biokinetic modeling, internal dose assessment, and safety standards and operational health physics practices.« less

Ultra-small plutonium oxide nanocrystals: an innovative material in plutonium science.

PubMed

Hudry, Damien; Apostolidis, Christos; Walter, Olaf; Janssen, Arne; Manara, Dario; Griveau, Jean-Christophe; Colineau, Eric; Vitova, Tonya; Prüssmann, Tim; Wang, Di; Kübel, Christian; Meyer, Daniel

2014-08-11

Apart from its technological importance, plutonium (Pu) is also one of the most intriguing elements because of its non-conventional physical properties and fascinating chemistry. Those fundamental aspects are particularly interesting when dealing with the challenging study of plutonium-based nanomaterials. Here we show that ultra-small (3.2±0.9 nm) and highly crystalline plutonium oxide (PuO2 ) nanocrystals (NCs) can be synthesized by the thermal decomposition of plutonyl nitrate ([PuO2 (NO3 )2 ]⋅3 H2 O) in a highly coordinating organic medium. This is the first example reporting on the preparation of significant quantities (several tens of milligrams) of PuO2 NCs, in a controllable and reproducible manner. The structure and magnetic properties of PuO2 NCs have been characterized by a wide variety of techniques (powder X-ray diffraction (PXRD), X-ray absorption fine structure (XAFS), X-ray absorption near edge structure (XANES), TEM, IR, Raman, UV/Vis spectroscopies, and superconducting quantum interference device (SQUID) magnetometry). The current PuO2 NCs constitute an innovative material for the study of challenging problems as diverse as the transport behavior of plutonium in the environment or size and shape effects on the physics of transuranium elements. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nuclear Data Sheets for A = 235

DOE Office of Scientific and Technical Information (OSTI.GOV)

Browne, E.; Tuli, J.K.

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=235. The highlight of this evaluation consists of the precise and comprehensive Coulomb excitation study (2012Wa35) on {sup 235}U, which in addition to the 7/2[743] ground state rotational band, extended the 1/2[631], 5/2[622], 5/2[752], and 3/2[631] rotational bands up to Jπ=53/2+, 49/2+, 441/2−, and 43/2+, respectively. This evaluation presents a study (2010Hu02) of the {sup 237}Np({sup 116}Sn, {sup 118}Snγ) reaction where the ground state rotational band 5/2[642] was observed up to Jπ=(53/2+). It is worth for historical knowledge tomore » mention the report on the “Discovery of isotopes of the transuranium elements with 93≤Z≤98” (2013Fr02), where the information for elements Np, Pu, and Am with mass number A=235 is given. {sup 235}Cf has not been observed. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r{sub 0}) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Nuclear Data Sheets for A = 235

DOE Office of Scientific and Technical Information (OSTI.GOV)

Browne, E.; Tuli, J. K.

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=235. The highlight of this evaluation consists of the precise and comprehensive Coulomb excitation study (2012Wa35) on ²³⁵U, which in addition to the 7/2[743] ground state rotational band, extended the 1/2[631], 5/2[622], 5/2[752], and 3/2[631] rotational bands up to Jπ=53/2+, 49/2+, 441/2–, and 43/2+, respectively. This evaluation presents a study (2010Hu02) of the ²³⁷Np(¹¹⁶Sn, ¹¹⁸Snγ) reaction where the ground state rotational band 5/2[642] was observed up to Jπ=(53/2+). It is worth for historical knowledge to mention the report onmore » the “Discovery of isotopes of the transuranium elements with 93≤Z≤98” (2013Fr02), where the information for elements Np, Pu, and Am with mass number A=235 is given. ²³⁵Cf has not been observed. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r₀) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Nuclear Data Sheets for A = 235

DOE PAGES

Browne, E.; Tuli, J. K.

2014-11-01

Spectroscopic data and level schemes from radioactive decay and nuclear reaction studies are presented here for all nuclei with mass number A=235. The highlight of this evaluation consists of the precise and comprehensive Coulomb excitation study (2012Wa35) on ²³⁵U, which in addition to the 7/2[743] ground state rotational band, extended the 1/2[631], 5/2[622], 5/2[752], and 3/2[631] rotational bands up to Jπ=53/2+, 49/2+, 441/2–, and 43/2+, respectively. This evaluation presents a study (2010Hu02) of the ²³⁷Np(¹¹⁶Sn, ¹¹⁸Snγ) reaction where the ground state rotational band 5/2[642] was observed up to Jπ=(53/2+). It is worth for historical knowledge to mention the report onmore » the “Discovery of isotopes of the transuranium elements with 93≤Z≤98” (2013Fr02), where the information for elements Np, Pu, and Am with mass number A=235 is given. ²³⁵Cf has not been observed. The alpha hindrance factors (HF) presented in this evaluation were calculated using values of the radius parameter (r₀) interpolated from those for even–even adjacent nuclei given by 1998Ak04.« less

Structural Analysis of Technical-Tactical Elements in Table Tennis and their Role in Different Playing Zones

PubMed Central

Munivrana, Goran; Petrinović, Lidija Zekan; Kondrič, Miran

2015-01-01

For the purpose of determining the overall structure of technical-tactical elements in table tennis and evaluating their role in different playing zones around the table, a new measuring instrument (a questionnaire) was formulated that took advantage of the expert knowledge of top, world class table tennis coaches. The results of the hierarchical taxonomic (cluster) analysis showed that the overall structure of the technical-tactical elements forming the table tennis technique could be divided into three basic groups; a group of technical-tactical elements (A) used in the phase of preparing one’s own and disabling the opponent’s attack; a group of technical-tactical elements (B) used in the phase of attack and counterattack; and a group of technical-tactical elements (C) used in the phase of defense. The differences among the obtained groups of table tennis elements were determined by applying the Kruskal-Wallis test, while relations between the groups and their role in different playing zones around the table were analyzed by comparing the average values of the experts’ scores. PMID:26557204

Structural Analysis of Technical-Tactical Elements in Table Tennis and their Role in Different Playing Zones.

PubMed

Munivrana, Goran; Petrinović, Lidija Zekan; Kondrič, Miran

2015-09-29

For the purpose of determining the overall structure of technical-tactical elements in table tennis and evaluating their role in different playing zones around the table, a new measuring instrument (a questionnaire) was formulated that took advantage of the expert knowledge of top, world class table tennis coaches. The results of the hierarchical taxonomic (cluster) analysis showed that the overall structure of the technical-tactical elements forming the table tennis technique could be divided into three basic groups; a group of technical-tactical elements (A) used in the phase of preparing one's own and disabling the opponent's attack; a group of technical-tactical elements (B) used in the phase of attack and counterattack; and a group of technical-tactical elements (C) used in the phase of defense. The differences among the obtained groups of table tennis elements were determined by applying the Kruskal-Wallis test, while relations between the groups and their role in different playing zones around the table were analyzed by comparing the average values of the experts' scores.

The socio-technical organisation of community pharmacies as a factor in the Electronic Prescription Service Release Two implementation: a qualitative study

PubMed Central

2012-01-01

Background The introduction of a new method of transmitting prescriptions from general practices to community pharmacies in England (Electronic Prescription Service Release 2 (EPS2)) has generated debate on how it will change work practice. As EPS2 will be a key technical element in dispensing, we reviewed the literature to find that there were no studies on how social and technical elements come together to form work practice in community pharmacies. This means the debate has little point of reference. Our aim therefore was to study the ways social and technical elements of a community pharmacy are used to achieve dispensing through the development of a conceptual model on pharmacy work practice, and to consider how a core technical element such the EPS2 could change work practice. Method We used ethnographic methods inclusive of case-study observations and interviews to collect qualitative data from 15 community pharmacies that were in the process of adopting or were soon to adopt EPS2. We analysed the case studies thematically and used rigorous multi-dimensional and multi-disciplinary interpretive validation techniques to cross analyse findings. Results In practice, dispensing procedures were not designed to take into account variations in human and technical integration, and assumed that repetitive and collective use of socio-technical elements were at a constant. Variables such as availability of social and technical resources, and technical know-how of staff were not taken into account in formalised procedures. Yet community pharmacies were found to adapt their dispensing in relation to the balance of social and technical elements available, and how much of the social and technical elements they were willing to integrate into dispensing. While some integrated as few technical elements as possible, some depended entirely on technical artefacts. This pattern also applied to the social elements of dispensing. Through the conceptual model development process, we identified three approaches community pharmacies used to appropriate procedures in practice. These were ‘technically oriented’, ‘improvising’ or ‘socially oriented’. Conclusion We offer a model of different work approaches community pharmacies use to dispense, which suggests that when adopting a core technical element such as the EPS2 system of dispensing there could be variations in its successful adoption. Technically oriented pharmacies might find it easiest to integrate a similar artefact into work practice although needs EPS2 to synchronise effectively with existing technologies. Pharmacies adopting an improvising-approach have the potential to improve how they organise dispensing through EPS2 although they will need to improve how they apply their operating procedures. Socially oriented pharmacies will need to dramatically adapt their approach to dispensing since they usually rely on few technical tools. PMID:23256484

The socio-technical organisation of community pharmacies as a factor in the Electronic Prescription Service Release Two implementation: a qualitative study.

PubMed

Harvey, Jasmine; Avery, Anthony J; Waring, Justin; Barber, Nick

2012-12-20

The introduction of a new method of transmitting prescriptions from general practices to community pharmacies in England (Electronic Prescription Service Release 2 (EPS2)) has generated debate on how it will change work practice. As EPS2 will be a key technical element in dispensing, we reviewed the literature to find that there were no studies on how social and technical elements come together to form work practice in community pharmacies. This means the debate has little point of reference. Our aim therefore was to study the ways social and technical elements of a community pharmacy are used to achieve dispensing through the development of a conceptual model on pharmacy work practice, and to consider how a core technical element such the EPS2 could change work practice. We used ethnographic methods inclusive of case-study observations and interviews to collect qualitative data from 15 community pharmacies that were in the process of adopting or were soon to adopt EPS2. We analysed the case studies thematically and used rigorous multi-dimensional and multi-disciplinary interpretive validation techniques to cross analyse findings. In practice, dispensing procedures were not designed to take into account variations in human and technical integration, and assumed that repetitive and collective use of socio-technical elements were at a constant. Variables such as availability of social and technical resources, and technical know-how of staff were not taken into account in formalised procedures. Yet community pharmacies were found to adapt their dispensing in relation to the balance of social and technical elements available, and how much of the social and technical elements they were willing to integrate into dispensing. While some integrated as few technical elements as possible, some depended entirely on technical artefacts. This pattern also applied to the social elements of dispensing. Through the conceptual model development process, we identified three approaches community pharmacies used to appropriate procedures in practice. These were 'technically oriented', 'improvising' or 'socially oriented'. We offer a model of different work approaches community pharmacies use to dispense, which suggests that when adopting a core technical element such as the EPS2 system of dispensing there could be variations in its successful adoption. Technically oriented pharmacies might find it easiest to integrate a similar artefact into work practice although needs EPS2 to synchronise effectively with existing technologies. Pharmacies adopting an improvising-approach have the potential to improve how they organise dispensing through EPS2 although they will need to improve how they apply their operating procedures. Socially oriented pharmacies will need to dramatically adapt their approach to dispensing since they usually rely on few technical tools.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Asok K. Ray

2012-05-22

During the past decades, considerable theoretical efforts have been devoted to studying the electronic and geometric structures and related properties of surfaces. Such efforts are particularly important for systems like the actinides for which experimental work is relatively difficult to perform due to material problems and toxicity. The actinides are characterized by a gradual filling of the 5f-electron shell with the degree of localization increasing with the atomic number Z along the last series of the periodic table. The open shell of the 5f electrons determines the atomic, molecular, and solid state properties of the actinide elements and their compoundsmore » and understanding the quantum mechanics of the 5f electrons is the defining issue in the chemistry and physics of actinide elements. These elements are also characterized by the increasing prominence of relativistic effects and their studies can, in fact, help us understand the role of relativity throughout the periodic table. However, the electronic and geometric structures of the actinides, specifically the trans-uranium actinides and the roles of the 5f electrons in chemical bonding are still not well understood. This is crucial not only for our understanding of the actinides but also for the fact that the actinides constitute 'the missing link' between the d transition elements and the lanthanides. The 5f orbitals have properties intermediate between those of localized 4f and delocalized 3d orbitals. Thus, a proper understanding of the actinides will help us understand the behavior of the lanthanides and transition metals as well. In fact, there is an urgent need for continued extensive and detailed theoretical research in this area to provide significant and deep understandings of the electronic and geometric structures of the actinides. In this work, we have performed electronic structure studies for plutonium (Pu), americium (Am), and curium (Cm) surfaces, and molecular adsorptions on Pu and Am surfaces. In particular, the region at the boundary of Pu and Am, is widely believed to be the crossover region between d-like itinerant and f-like localized behavior The eventual goal is a complete understanding of the surface chemistry and physics processes of all actinide surfaces, defining the chemistry and physics of such heavy elements. Among the actinides, plutonium, with five 5f electrons in the solid state, is arguably the most complex, fascinating, and enigmatic element known to mankind and has attracted extraordinary scientific and technological interests because of its unique properties, generating a significant body of research in diverse areas, including superconductivity. Pu has, at least, six stable allotropes between room temperature and melting at atmospheric pressure, indicating that the valence electrons can hybridize into a number of complex bonding arrangements. Central and critical questions relate to the electronic structure, localization of the 5f electrons and the magnetism of Pu. For the light-actinides, from Th to Pu, the 5f electrons are believed to be delocalized, hybridizing with the 6d and 7s electrons. For the heavier actinides, Am and beyond, the 5f electrons are localized with the 5f orbitals progressively lower in energy relative to the 6d configuration. Hence, Pu is in a position where the 5f electronic behavior changes from itinerant to localized. As far as magnetism is concerned, a majority of the theoretical calculations continues to claim the existence of magnetism while almost all the experimental results do not find any support for such claims. The second element of interest to us, namely americium, occupies a central position in the actinide series with respect to the involvement of 5f electrons in metallic bonding. It is widely believed that the 5f electrons in Am are localized and that Am undergoes a series of crystallographic phase changes with pressure. Fully-relativistic all electron surface studies of the different phases of Am, initially for the dhcp and the fcc surfaces, can and have provided us with valuable information about chemical bonding in Am and the transitions from f-electron delocalization to f-electron localization in trans-uranium compounds. In particular, a comparative study of the electronic structures of the Pu and Am surfaces using the techniques of all-electron modern density functional theory and beyond can provide significant information about the role of 5f electrons in bond formation as also the localization of the 5f electrons, matters of considerable controversies. The change from metallic 5f bonding into local-moment nonbonding configurations that takes place between Pu and Am is rather unique in the periodic table and is at the very heart of our understanding of electronic structure. We believe that, considering the narrow bandwidth of surface states, any transition from itinerant to localized behavior first takes place at the actinide surfaces with possible reconstructions.« less

United States Transuranium and Uranium Registries. Annual report, February 1, 2003 - January 31, 2004

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alldredge, J. R.; Brumbaugh, T. L.; Ehrhart, Susan M.

2004-01-31

This year was my fourteenth year with the U. S. Transuranium and Uranium Registries (USTUR). How time flies! Since I became the director of the program five years ago, one of my primary goals was to increase the usefulness of the large USTUR database that consists of six tables containing personal information, medical histories, radiation exposure histories, causes of death, and the results of radiochemical analysis of organ samples collected at autopsy. It is essential that a query of one or more of these tables by USTUR researchers or by collaborating researchers provides complete and reliable information. Also, some ofmore » the tables (those without personal identifiers) are destined to appear on the USTUR website for the use of the scientific community. I am pleased to report that most of the data in the database have now been verified and formatted for easy query. It is important to note that no data were discarded; copies of the original tables were retained and the original paper documents are still available for further verification of values as needed.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchetti, M.; University of Montpellier, IES, UMR 5214, F-34000, Montpellier; Laux, D.

During irradiation UO{sub 2} nuclear fuel experiences the development of a non-uniform distribution of porosity which contributes to establish varying mechanical properties along the radius of the pellet. Radial variations of the porosity and of elastic properties in high burnup UO{sub 2} pellet can be investigated via high frequency acoustic microscopy. Ultrasound waves are generated by a piezoelectric transducer and focused on the sample, after having travelled through a coupling liquid. The elastic properties of the material are related to the velocity of the generated Rayleigh surface wave (VR). A 67 MWd/kgU UO{sub 2} pellet was characterized using the acousticmore » microscope installed in the hot cells of the Institute of Transuranium Elements: 90 MHz frequency was applied, methanol was used as coupling liquid and VR was measured at different radial positions. By comparing the porosity values obtained via acoustic microscopy with those determined using ceramographic image analysis a good agreement was found, especially in the areas close to the centre. In addition Young's modulus was calculated and its radial profile was correlated to the corresponding burnup profile. (authors)« less

Uptake and effects of americium-241 on a brackishwater amphipod

NASA Astrophysics Data System (ADS)

Hoppenheit, M.; Murray, C. N.; Woodhead, D. S.

1980-03-01

The present paper reports the results of experimental work undertaken using the brackish-water amphipod Gammarus duebeni duebeni and the transuranium nuclide americium-241. Data on the accumulation of this actinide showed that the larger fraction of the total body burden is associated with the exoskeleton. It was found that the body burden remained constant in the range pH 8.0 6.5 even though the water concentrations changed markedly. It would thus appear that the concept of a concentration factor should be re-examined and it is proposed that a factor should be defined in terms of environmental and chemical parameters which represent the bioavailable fraction of the actinide. The effect of americium on survival and moulting was studied at two activity concentrations; the dose rates and absorbed doses under the experimental conditions employed have been estimated. The differences in survival rates between the control and irradiated groups were statistically analyzed and the significant difference at the higher concentration is believed to be due to a synergism between physiological stress and radiotoxicity of americium rather than the chemical toxicity of the element.

Radionuclide concentration processes in marine organisms: A comprehensive review.

PubMed

Carvalho, Fernando P

2018-06-01

The first measurements made of artificial radionuclides released into the marine environment did reveal that radionuclides are concentrated by marine biological species. The need to report radionuclide accumulation in biota in different conditions and geographical areas prompted the use of concentration factors as a convenient way to describe the accumulation of radionuclides in biota relative to radionuclide concentrations in seawater. Later, concentration factors became a tool in modelling radionuclide distribution and transfer in aquatic environments and to predicting radioactivity in organisms. Many environmental parameters can modify the biokinetics of accumulation and elimination of radionuclides in marine biota, but concentration factors remained a convenient way to describe concentration processes of radioactive and stable isotopes in aquatic organisms. Revision of CF values is periodically undertaken by international organizations, such as the International Atomic Energy Agency (IAEA), to make updated information available to the international community. A brief commented review of radionuclide concentration processes and concentration factors in marine organisms is presented for key groups of radionuclides such as fission products, activation products, transuranium elements, and naturally-occurring radionuclides. Copyright © 2017 Elsevier Ltd. All rights reserved.

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of technical assistance to migrant health centers and entities which intend to become migrant health centers... the grant award, such technical and other nonfinancial assistance (such as fiscal and program...

Feasibility study of an Integrated Program for Aerospace vehicle Design (IPAD). Volume 5: Catalog of IPAD technical program elements

NASA Technical Reports Server (NTRS)

Gillette, W. B. (Editor); Southall, J. W. (Editor)

1973-01-01

The catalog is presented of technical program elements which are required to support the design activities for a subsonic and supersonic commercial transport. Information for each element consists of usage and storage information, ownership, status and an abstract describing the purpose of the element.

48 CFR 315.305 - Proposal evaluation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... following elements: (1) An explanation of the evaluation process and the role of evaluators throughout the... include, at a minimum, the following elements: (1) A list of recommended technical evaluation panel... that the technical evaluation will have in the award decision. (2) The technical evaluation process...

Analyses of Radiation and Mesothelioma in the US Transuranium and Uranium Registries

PubMed Central

Fulcher, Keri; Nagarajan, Sumitha; McCord, Stacey; Fallahian, Naz Afarin; Hoffman, Heather J.; Haver, Cary; Tolmachev, Sergei

2013-01-01

Objectives. We examined the relationship between radiation and excess deaths from mesothelioma among deceased nuclear workers who were part of the US Transuranium and Uranium Registries. Methods. We performed univariate analysis with SAS Version 9.1 software. We conducted proportionate mortality ratio (PMR) and proportionate cancer mortality ratio (PCMR) analyses using the National Institute for Occupational Safety and Health Life Table Analysis System with the referent group being all deaths in the United States. Results. We found a PMR of 62.40 (P < .05) and a PCMR of 46.92 (P < .05) for mesothelioma. PMRs for the 4 cumulative external radiation dose quartiles were 61.83, 57.43, 74.46, and 83.31. PCMRs were 36.16, 47.07, 51.35, and 67.73. The PMR and PCMR for trachea, bronchus, and lung cancer were not significantly elevated. Conclusions. The relationship between cumulative external radiation dose and the PMR and PCMR for mesothelioma suggests that external radiation at nuclear facilities is associated with an increased risk of mesothelioma. The lack of a significantly elevated PMR and PCMR for trachea, bronchus, and lung cancer suggests that asbestos did not confound this relationship. PMID:23409888

Glenn T. Seaborg - Contributions to Advancing Science

Science.gov Websites

. Documents: The First Weighing of Plutonium (Atomic Number 94); DOE Technical Report; September 1967 The New Element Americium (Atomic Number 95); DOE Technical Report; January 1948 The New Element Curium (Atomic Number 96); DOE Technical Report; January 1948 Frontiers of Chemistry for Americium and Curium; DOE

[The visual perception of the elements of technical drawings among masking distractions in advanced and nonadvanced students in the building and architectural professions].

PubMed

Balichev, Iu

1997-01-01

To investigation were submitted the particularities of the process of visual perception of technical drawings and schemes in advanced and backward pupils, who were mastering the specialties of "building and architecture", "hydroconstruction", "transport construction", "geodesy". The time was registered, which was necessary to advanced and backward pupils for unveiling the different elements in the drawing, scheme, and such attributes of the drawing as: orientation, length, curves of the lined, the boundary between them; time for identification of the specific designations, symbols, group of symbols, elements of the sketch from the simple to the complex ones. The results of the investigations revealed that in the advanced pupils the perception (unveiling) of the different elements of the technical drawing proceeded very rapidly, almost automatically. In the backward pupils this process elapsed reliably more slowly. It was demonstrated that the growing up pupils, who were distinguished with more rapid perception of the different elements of the drawing (advanced ones) more rapidly and more exactly dealt with solution of the technical tasks as compared with these, who more slowly unveiled the looked for elements (backwardness). Some other individual particularities were also established with respect to the visual perception of the elements of the technical drawing and its properties in advanced and backward pupils who were mastering the investigated professions.

Research and development plan for the Slagging Pyrolysis Incinerator. [For TRU waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hedahl, T.G.; McCormack, M.D.

1979-01-01

Objective is to develop an incinerator for processing disposed transuranium waste. This R and D plan describes the R and D efforts required to begin conceptual design of the Slagging Pyrolysis Incinerator (Andco-Torrax). The program includes: incinerator, off-gas treatment, waste handling, instrumentation, immobilization analyses, migration studies, regulations, Belgium R and D test plan, Disney World test plan, and remote operation and maintenance. (DLC)

Preliminary developments of MTR plates with uranium nitride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Durand, J.P.; Laudamy, P.; Richter, K.

1997-08-01

In the opinion of CERCA, the total weight of Uranium per MTR plate (without changing the external dimensions) cannot be further increased using U{sub 3}Si{sub 2}. Limits have been reached on plates with a thicker meat or loaded to 6g Ut/cm{sup 3}. The use of a denser fuel like Uranium mononitride could permit an increase in these limits. A collaboration between the Institute for Transuranium Elements (ITU), Joint Research Centre of the European Commission, and CERCA has been set ut. The preliminary studies at the ITU to check compatibility between aluminium and UN proved that there are no metallurgical interactionsmore » below 500{degrees}C. Feasibility of the manufacturing, on a laboratory scale at CERCA, of depleted Uranium mononitride plates loaded to 7 g Ut/cm{sup 3} has been demonstrated. The manufacturing process, however, is only one aspect of the development of a new fuel. The experience gained in the case of U{sub 3}Si{sub 2} has shown that the development of a new fuel requires considerable time and financial investment. Such a development certainly represents an effort of about 10 years.« less

Approaches to Manufacturing Alpha Emitters For Radioimmunotherapeutic Drugs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaylord King, A.; Givens, Kenneth R.; Miller, William H.

Several alpha emitting isotopes have been proposed for radioimmunotherapy. To produce these nuclides reliably and in quantities needed, unique manufacturing approaches will be required. This paper describes the approaches that are being developed for the manufacture of 225Actinium (225 Ac) that decays to 213Bismuth (213 Bi) and the commercial manufacturing approaches. Oak Ridge National Laboratory (ORNL) currently supplies the actinium used for research and medical use. Today the ORNL 233U stockpiles only provide sufficient material for research quantities of 213 Bi. At the Institute for Transuranium Elements (ITU), in Karlsruhe, researchers have also developed a method of irradiating radium-226 withmore » protons in a cyclotron to produce actinium- 225 through the reaction 226Ra (p, 2n) 225Ac. Researchers from the Missouri University (MU), the Missouri University Research Reactor (MURR), MedActinium, Inc. and Los Alamos National Laboratory (LANL) are working on a collaborative effort to benchmark and optimize the production of 213Bi via neutron bombardment of 226Ra. MedActinium, Inc., in collaboration with commercial and institutional investigators at PG Research Foundation (PGRF) and Memorial Sloan Kettering Cancer Center (MSKCC), is developing commercial approaches to manufacturing these unique radioimmunotherapeutic drugs.« less

TRANSURANUS: a fuel rod analysis code ready for use

NASA Astrophysics Data System (ADS)

Lassmann, K.

1992-06-01

TRANSURANUS is a computer program for the thermal and mechanical analysis of fuel rods in nuclear reactors and was developed at the European Institute for Transuranium Elements (TUI). The TRANSURANUS code consists of a clearly defined mechanical-mathematical framework into which physical models can easily be incorporated. Besides its flexibility for different fuel rod designs the TRANSURANUS code can deal with very different situations, as given for instance in an experiment, under normal, off-normal and accident conditions. The time scale of the problems to be treated may range from milliseconds to years. The code has a comprehensive material data bank for oxide, mixed oxide, carbide and nitride fuels, Zircaloy and steel claddings and different coolants. During its development great effort was spent on obtaining an extremely flexible tool which is easy to handle, exhibiting very fast running times. The total development effort is approximately 40 man-years. In recent years the interest to use this code grew and the code is in use in several organisations, both research and private industry. The code is now available to all interested parties. The paper outlines the main features and capabilities of the TRANSURANUS code, its validation and treats also some practical aspects.

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B2: Education. Technical Report 49B2

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element, including its purpose, values, base populations and…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements A: Demographics. Technical Report 49A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements C: Employment. Technical Report 49C

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements D: Social. Technical Report 49D

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

Longitudinal Surveys of Australian Youth (LSAY): 1998 Cohort--User Guide. Data Elements D: Social. Technical Report 53D

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 1998 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B1: Education. Technical Report 49B1

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant.…

Technical Elements of Transportation. Grade 11-12. Course #8176 (Semester). Technology Education Course Guide. Industrial Arts/Technology Education.

ERIC Educational Resources Information Center

North Carolina State Dept. of Public Instruction, Raleigh. Div. of Vocational Education.

This guide is intended for use in teaching a course in the history of the development of transportation systems and the individual elements in such systems. The course is designed to break transportation systems down into their individual components so as to make it possible to study system types, media, technical elements, and environmental…

Liver CT image processing: a short introduction of the technical elements.

PubMed

Masutani, Y; Uozumi, K; Akahane, Masaaki; Ohtomo, Kuni

2006-05-01

In this paper, we describe the technical aspects of image analysis for liver diagnosis and treatment, including the state-of-the-art of liver image analysis and its applications. After discussion on modalities for liver image analysis, various technical elements for liver image analysis such as registration, segmentation, modeling, and computer-assisted detection are covered with examples performed with clinical data sets. Perspective in the imaging technologies is also reviewed and discussed.

Technical Information Resource on Rare Earth Elements Now Available to Public and Private Sector Stakeholders

EPA Science Inventory

A new EPA technical information resource, “Rare Earth Elements: A Review of Production, Processing, Recycling, and Associated Environmental Issues” has been produced as an introductory resource for those interested in learning more about REE mining and alternatives to meet demand...

Application of annular centrifugal contactors in the hot test of the improved total partitioning process for high level liquid waste.

PubMed

Duan, Wuhua; Chen, Jing; Wang, Jianchen; Wang, Shuwei; Feng, Xiaogui; Wang, Xinghai; Li, Shaowei; Xu, Chao

2014-08-15

High level liquid waste (HLLW) produced from the reprocessing of the spent nuclear fuel still contains moderate amounts of uranium, transuranium (TRU) actinides, (90)Sr, (137)Cs, etc., and thus constitutes a permanent hazard to the environment. The partitioning and transmutation (P&T) strategy has increasingly attracted interest for the safe treatment and disposal of HLLW, in which the partitioning of HLLW is one of the critical technical issues. An improved total partitioning process, including a TRPO (tri-alkylphosphine oxide) process for the removal of actinides, a CESE (crown ether strontium extraction) process for the removal of Sr, and a CECE (calixcrown ether cesium extraction) process for the removal of Cs, has been developed to treat Chinese HLLW. A 160-hour hot test of the improved total partitioning process was carried out using 72-stage 10-mm-dia annular centrifugal contactors (ACCs) and genuine HLLW. The hot test results showed that the average DFs of total α activity, Sr and Cs were 3.57 × 10(3), 2.25 × 10(4) and 1.68 × 10(4) after the hot test reached equilibrium, respectively. During the hot test, 72-stage 10-mm-dia ACCs worked stable, continuously with no stage failing or interruption of the operation. Copyright © 2014 Elsevier B.V. All rights reserved.

Transmutation of All German Transuranium under Nuclear Phase Out Conditions – Is This Feasible from Neutronic Point of View?

PubMed Central

Merk, Bruno; Litskevich, Dzianis

2015-01-01

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P&T) could be considered as a technological option for the management of highly radioactive waste, therefore a wide study has been conducted. In the study group objectives for P&T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed from neutronics point of view using simulations of a molten salt reactor with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible from neutronic point of view in a time frame of about 60 years. For this task three reactors of a mostly new technology would have to be developed and a twofold life cycle consisting of a transmuter operation and a deep burn phase would be required. A basic insight for the optimization of the time duration of the deep burn phase is given. Further on, a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation in the molten salt fast reactor. The effect of modeling and simulation is investigated based on three different modeling strategies and two different code versions. PMID:26717509

Transmutation of All German Transuranium under Nuclear Phase Out Conditions - Is This Feasible from Neutronic Point of View?

PubMed

Merk, Bruno; Litskevich, Dzianis

2015-01-01

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P&T) could be considered as a technological option for the management of highly radioactive waste, therefore a wide study has been conducted. In the study group objectives for P&T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed from neutronics point of view using simulations of a molten salt reactor with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible from neutronic point of view in a time frame of about 60 years. For this task three reactors of a mostly new technology would have to be developed and a twofold life cycle consisting of a transmuter operation and a deep burn phase would be required. A basic insight for the optimization of the time duration of the deep burn phase is given. Further on, a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation in the molten salt fast reactor. The effect of modeling and simulation is investigated based on three different modeling strategies and two different code versions.

The United States Transuranium and Uranium Registries. Revision 1, [Annual] report, October 1, 1990--April 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.

1992-09-01

This paper describes the history, organization, activities and recent scientific accomplishments of the United States Transuranium and Uranium Registries. Through voluntary donations of tissue obtained at autopsies, the Registries carry out studies of the concentration, distribution and biokinetics of plutonium in occupationally exposed persons. Findings from tissue analyses from more than 200 autopsies include the following: a greater proportion of the americium intake, as compared with plutonium, was found in the skeleton; the half-time of americium in liver is significantly shorter than that of plutonium; the concentration of actinide in the skeleton is inversely proportional to the calcium and ashmore » content of the bone; only a small percentage of the total skeletal deposition of plutonium is found in the marrow, implying a smaller risk from irradiation of the marrow relative to the bone surfaces; estimates of plutonium body burden made from urinalysis typically exceed those made from autopsy data; pathologists were unable to discriminate between a group of uranium workers and persons without known occupational exposure on the basis of evaluation of microscopic kidney slides; the skeleton is an important long term depot for uranium, and that the fractional uptake by both skeleton and kidney may be greater than indicated by current models. These and other findings and current studies are discussed in depth.« less

THE ROLE OF AQUEOUS THIN FILM EVAPORATIVE COOLING ON RATES OF ELEMENTAL MERCURY AIR-WATER EXCHANGE UNDER TEMPERATURE DISEQUILIBRIUM CONDITIONS

EPA Science Inventory

The technical conununity has only recently addressed the role of atmospheric temperature variations on rates of air-water vapor phase toxicant exchange. The technical literature has documented that: 1) day time rates of elemental mercury vapor phase air-water exchange can exceed ...

An Object-Oriented Architecture for Intelligent Tutoring Systems. Technical Report No. LSP-3.

ERIC Educational Resources Information Center

Bonar, Jeffrey; And Others

This technical report describes a generic architecture for building intelligent tutoring systems which is developed around objects that represent the knowledge elements to be taught by the tutor. Each of these knowledge elements, called "bites," inherits both a knowledge organization describing the kind of knowledge represented and…

77 FR 52698 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... training equipment, publications and technical data, U.S. Government and contractor technical and logistics personnel services and other related elements of program and logistics support. (iv) Military Department..., publications and technical data, U.S. Government and contractor technical and logistics personnel services and...

Non-equilibrium radiation nuclear reactor

NASA Technical Reports Server (NTRS)

Thom, K.; Schneider, R. T. (Inventor)

1978-01-01

An externally moderated thermal nuclear reactor is disclosed which is designed to provide output power in the form of electromagnetic radiation. The reactor is a gaseous fueled nuclear cavity reactor device which can operate over wide ranges of temperature and pressure, and which includes the capability of processing and recycling waste products such as long-lived transuranium actinides. The primary output of the device may be in the form of coherent radiation, so that the reactor may be utilized as a self-critical nuclear pumped laser.

Thermionic fuel element for the S-prime reactor

NASA Astrophysics Data System (ADS)

Van Hagan, Thomas H.; Drees, Elizabeth A.

1993-01-01

Technical aspects of the thermionic fuel element (TFE) design proposed for the S-PRIME space nuclear power system are discussed. Topics covered include the rational for selecting a multicell TFE approach, a technical description of the S-PRIME TFE and its estimated performance, and the technology readiness of the design, which emphasizes techology maturity and low risk.

A Preliminary Rhetoric of Technical Copywriting.

ERIC Educational Resources Information Center

Henson, Leigh

1994-01-01

Discusses the rhetorical elements of technical copywriting, including its shared communicative aims with technical writing; authorship considerations such as ethics, education, and professionalism; and the concerns of promotional strategy, audience analysis, choice of media and materials, writing strategy, and style. (SR)

Design and Delivery of Technical Module for the Business Intelligence Course

ERIC Educational Resources Information Center

Wang, Shouhong; Wang, Hai

2013-01-01

IS programs are increasingly being called on to offer courses in business intelligence. This article presents the pedagogical design and the delivery method of a practicable technical module for a non-technically oriented Business Intelligence course. It is a tutorial for the instructors who wish to incorporate a practical technical element in…

The Transuranium Elements: Early History (Nobel Lecture)

DOE R&D Accomplishments Database

McMillan, E. M.

1951-12-12

In this talk the author tells of the circumstances that led to the discovery of neptunium, the first element beyond uranium, and the partial identification of plutonium, the next one beyond that. The part of the story that lies before 1939 has already been recounted here in the Nobel lectures of Fermi and Hahn. Rather the author starts with the discovery of fission by Hahn and Strassmann. News of this momentous discovery reached Berkeley early in 1939. The staff of the Radiation Laboratory was put into a state of great excitement and several experiments of a nature designed to check and extend the announced results were started, using ionization chambers and pulse amplifiers, cloud chambers, chemical methods, and so forth. The author decided to do an experiment of a very simple kind. When a nucleus of uranium absorbs a neutron and fission takes place, the two resulting fragments fly apart with great violence, sufficient to propel them through air or other matter for some distance. This distance, called the "range", is quantity of some interest, and the author undertook to measure it by observing the depth of penetration of the fission fragments in a stack of thin aluminum foils. The fission fragments came from a thin layer of uranium oxide spread on a sheet of paper, and exposed to neutrons from a beryllium target bombarded by 8 Mev deuterons in the 37-inch cyclotron. The aluminum foils, each with a thickness of about half a milligram per square centimeter, were stacked like the pages of a book in immediate contact with the layer of uranium oxide. After exposure to the neutrons, the sheets of aluminum were separated and examined for radioactivity by means of an ionization chamber. The fission fragments of course are radioactive atoms, and their activity is found where they stop.

Technical Preparation: Preparing Students for Success. A Position Paper Presented by the Wisconsin Association of Secondary Vocational Administrators 1991-1992.

ERIC Educational Resources Information Center

Peterson, Charlene; And Others

Technical Preparation (Tech Prep) programs include basic skills and competencies to improve students' school-to-work transition. The following elements characterize Tech Prep: designed for grades 9-14, leading to an technical associate degree; parallels college preparatory program; offers technical program of study in business enterprise,…

Development of a behavioural marker system for scrub practitioners' non-technical skills (SPLINTS system).

PubMed

Mitchell, Lucy; Flin, Rhona; Yule, Steven; Mitchell, Janet; Coutts, Kathy; Youngson, George

2013-04-01

Adverse events still occur despite ongoing efforts to reduce harm to patients. Contributory factors to adverse events are often due to limitations in clinicians' non-technical skills (e.g. communication, situation awareness), rather than deficiencies in technical competence. We developed a behavioural rating system to provide a structured means for teaching and assessing scrub practitioners' (i.e. nurse, technician, operating department practitioner) non-technical skills. Psychologists facilitated focus groups (n = 4) with experienced scrub practitioners (n = 16; 4 in each group) to develop a preliminary taxonomy. Focus groups reviewed lists of non-technical-skill-related behaviours that were extracted from an interview study. The focus groups labelled skill categories and elements and also provided examples of good and poor behaviours for those skills. An expert panel (n = 2 psychologists; n = 1 expert nurse) then used an iterative process to individually and collaboratively review and refine those data to produce a prototype skills taxonomy. A preliminary taxonomy containing eight non-technical skill categories with 28 underlying elements was produced. The expert panel reduced this to three categories (situation awareness, communication and teamwork, task management), each with three underlying elements. The system was called the Scrub Practitioners' List of Intraoperative Non-Technical Skills system. A scoring system and a user handbook were also developed. A prototype behavioural rating system for scrub practitioners' non-technical skills was developed, to aid in teaching and providing formative assessment. This important aspect of performance is not currently explicitly addressed in any educational route to qualify as a scrub practitioner. © 2012 Blackwell Publishing Ltd.

2012 Technical Corrections Fact Sheet

EPA Pesticide Factsheets

Final Rule: 2012 Technical Corrections, Clarifying and Other Amendments to theGreenhouse Gas Reporting Rule, and Confidentiality Determinations for Certain DataElements of the Fluorinated Gas Source Category

Assessing Nurse Anaesthetists' Non-Technical Skills in the operating room.

PubMed

Lyk-Jensen, H T; Jepsen, R M H G; Spanager, L; Dieckmann, P; Østergaard, D

2014-08-01

Incident reporting and fieldwork in operating rooms have shown that some of the errors that arise in anaesthesia relate to inadequate use of non-technical skills. To provide a tool for training and feedback on nurse anaesthetists' non-technical skills, this study aimed to adapt the Anaesthetists' Non-Technical Skills (ANTS) as a behavioural marker system for the formative assessment of nurse anaesthetists' non-technical skills in the operating room. A qualitative approach with focus group interviews was used to identify the non-technical skills of nurse anaesthetists in the operating room. The interview data were transcribed verbatim. Directed content analysis was used to code and sort data deductively into the ANTS categories: task management, team working, situation awareness and decision making. The prototype named Nurse Anaesthetists' Non-Technical Skills (N-ANTS) was presented and discussed in a group of subject matter experts to ensure face validity. The N-ANTS system consists of the same four categories as ANTS and 15 underlying elements. Three to five good and poor behavioural markers for each element were identified. The headings and definitions of the categories and elements were adjusted to encompass the behavioural markers in N-ANTS. The differences that emerged mainly reflected statements regarding the establishment of role, competence, and task delegation. A behavioural marker system, N-ANTS, for nurse anaesthetists was adapted from a behavioural marker system, ANTS, for anaesthesiologists. © 2014 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Technical Report

DTIC Science & Technology

2018-04-01

Technical Report ARWSB-TR-18025 Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Technical Report Lucas B...1. REPORT DATE (DD-MM-YYYY) April 2018 2. REPORT TYPE Technical 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Hydraulic Testing of...Polymer Matrix Composite 102mm Tube Section Technical Report 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER

A theoretical probe of high-valence uranium and transuranium silylamides: Structural and redox properties

NASA Astrophysics Data System (ADS)

Zhong, Yu-Xi; Guo, Yuan-Ru; Pan, Qing-Jiang

2016-02-01

Relativistic density functional theory was used to explore the structural and redox properties of 18 prototypical actinyl silylamides including a variation of metals (U, Np and Pu), metal oxidation states (VI and V) and equatorial ligands. A theoretical approach associated with implicit solvation and spin-orbit/multiplet corrections was proved to be reliable. A marked shift of reduction potentials of actinyl silylamides caused by changes of equatorial coordination ligands and implicit solvation was elucidated by analyses of electronic structures and single-electron reduction mechanism.

Air Force Research Laboratory Wright Site Guide to Technical Publishing

DTIC Science & Technology

2005-04-01

Scientific and Technical Reports—Elements, Organization, and Design manual (and a version modified for documents generated for AFRL) • Merriam-Webster’s...notice page --SF 298 --original graphics /halftones Indicate the following on the letter of transmittal sheet: --quantity of copies required for...Elements, Organization and Design ? The WRS CDRL for a final report requires that the standard be followed. The only exception is SBIR Phase 1

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis project

NASA Technical Reports Server (NTRS)

Baresi, Larry

1989-01-01

The Annual Report presents the fiscal year (FY) 1988 research activities and accomplishments, for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division. The ECUT Biocatalysis Project is managed by the Jet Propulsion Laboratory, California Institute of Technology. The Biocatalysis Project is a mission-oriented, applied research and exploratory development activity directed toward resolution of the major generic technical barriers that impede the development of biologically catalyzed commercial chemical production. The approach toward achieving project objectives involves an integrated participation of universities, industrial companies and government research laboratories. The Project's technical activities were organized into three work elements: (1) The Molecular Modeling and Applied Genetics work element includes research on modeling of biological systems, developing rigorous methods for the prediction of three-dimensional (tertiary) protein structure from the amino acid sequence (primary structure) for designing new biocatalysis, defining kinetic models of biocatalyst reactivity, and developing genetically engineered solutions to the generic technical barriers that preclude widespread application of biocatalysis. (2) The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields and lower separation energetics. Results of work within this work element will be used to establish the technical feasibility of critical bioprocess monitoring and control subsystems. (3) The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the energy-economics of biocatalyzed chemical production processes, and initiation of technology transfer for advanced bioprocesses.

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis project

NASA Astrophysics Data System (ADS)

Baresi, Larry

1989-03-01

The Annual Report presents the fiscal year (FY) 1988 research activities and accomplishments, for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division. The ECUT Biocatalysis Project is managed by the Jet Propulsion Laboratory, California Institute of Technology. The Biocatalysis Project is a mission-oriented, applied research and exploratory development activity directed toward resolution of the major generic technical barriers that impede the development of biologically catalyzed commercial chemical production. The approach toward achieving project objectives involves an integrated participation of universities, industrial companies and government research laboratories. The Project's technical activities were organized into three work elements: (1) The Molecular Modeling and Applied Genetics work element includes research on modeling of biological systems, developing rigorous methods for the prediction of three-dimensional (tertiary) protein structure from the amino acid sequence (primary structure) for designing new biocatalysis, defining kinetic models of biocatalyst reactivity, and developing genetically engineered solutions to the generic technical barriers that preclude widespread application of biocatalysis. (2) The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields and lower separation energetics. Results of work within this work element will be used to establish the technical feasibility of critical bioprocess monitoring and control subsystems. (3) The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the energy-economics of biocatalyzed chemical production processes, and initiation of technology transfer for advanced bioprocesses.

[Improvement of sanitary and epidemiological safety of rail transport--a requirement of the new legislation of the Russian Federation].

PubMed

2012-01-01

Brief analysis of the legal framework in recent years, both in the sphere of technical regulation, and in the field of sanitary and epidemiological welfare of the population is presented in this article. The necessity of inclusion in the technical regulations for the safety of railway rolling stock and elements of railway infrastructure the requirements for sanitary-epidemiological safety and hygiene regulations has been proved. Fragments of technical regulations for railway equipment and infrastructure elements, including the basic requirements for the sanitary-epidemiological security are presented. The position of authors in the processing of the regulatory framework in the field of sanitary-epidemiological welfare of population in standardization documents in accordance with the requirements of federal law "On technical regulation" has been reflected.

76 FR 35103 - Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

... which initial and transition flight training must include an in-flight element. Technical Amendment This.... 28471; Amendment Nos. 121-355 and 135-125] RIN 2120-AF08 Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment AGENCY: Federal Aviation Administration (FAA...

Screen Layout Design: Research into the Overall Appearance of the Screen.

ERIC Educational Resources Information Center

Grabinger, R. Scott

1989-01-01

Examines the current state of research into the visual effects of screen designs used in computer-assisted instruction and suggests areas for future efforts. Topics discussed include technical elements and comprehensibility elements in layout design; single element and multiple element research methodologies; dependent variables; and learning…

Plutonium and americium in the foodchain lichen-reindeer-man

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaakkola, T.; Hakanen, M.; Keinonen, M.

1977-01-01

The atmospheric nuclear tests have produced a worldwide fallout of transuranium elements. In addition to plutonium measurable concentrations of americium are to be found in terrestrial and aquatic environments. The metabolism of plutonium in reindeer was investigated by analyzing plutonium in liver, bone, and lung collected during 1963-1976. To determine the distribution of plutonium in reindeer all tissues of four animals of different ages were analyzed. To estimate the uptake of plutonium from the gastrointestinal tract in reindeer, the tissue samples of elk were also analyzed. Elk which is of the same genus as reindeer does not feed on lichenmore » but mainly on deciduous plants, buds, young twigs, and leaves of trees and bushes. The composition of its feed corresponds fairly well to that of reindeer during the summer. Studies on behaviour of americium along the foodchain lichen-reindeer-man were started by determining the Am-241 concentrations in lichen and reindeer liver. The Am-241 results were compared with those of Pu-239,240. The plutonium contents of the southern Finns, whose diet does not contain reindeer tissues, were determined by analyzing autopsy tissue samples (liver, lung, and bone). The southern Finns form a control group to the Lapps consuming reindeer tissues. Plutonium analyses of the placenta, blood, and tooth samples of the Lapps were performed.« less

47 CFR 51.307 - Duty to provide access on an unbundled basis to network elements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... network elements. 51.307 Section 51.307 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Carriers § 51.307 Duty to provide access on an unbundled basis to network elements. (a) An incumbent LEC... service, nondiscriminatory access to network elements on an unbundled basis at any technically feasible...

47 CFR 51.307 - Duty to provide access on an unbundled basis to network elements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... network elements. 51.307 Section 51.307 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Carriers § 51.307 Duty to provide access on an unbundled basis to network elements. (a) An incumbent LEC... service, nondiscriminatory access to network elements on an unbundled basis at any technically feasible...

41 CFR Appendix C to Chapter 301 - Standard Data Elements for Federal Travel [Traveler Identification

Code of Federal Regulations, 2014 CFR

2014-07-01

... education, in scientific, professional, technical, mechanical, trade, clerical, fiscal, administrative, or... Data Elements for Federal Travel [Accounting & Certification] Group name Data elements Description Accounting Classification Accounting Code Agency accounting code. Non-Federal Source Indicator Per Diem...

Elements of a Research Report.

ERIC Educational Resources Information Center

Schurter, William J.

This guide for writing research or technical reports discusses eleven basic elements of such reports and provides examples of "good" and "bad" wordings. These elements are the title, problem statement, purpose statement, need statement, hypothesis, assumptions, procedures, limitations, terminology, conclusion and recommendations. This guide is…

An arm phantom for in vivo determination of Americium-241 in bone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kephart, G.S.; Palmer, H.E.

1988-04-01

The focus of this research has been to construct a realistic arm phantom as a calibration tool in estimation of /sup 241/Am in the bone. The United States Transuranium Registry (USTR), through its program of whole body donations, continues to provide data on transuranic incorporation in man that would not otherwise be readily available (Norwood 1972; Breitenstein 1981; Swint, et al. 1985). This project uses well-characterized human bones loaned by the USTR for the construction of realistic phantoms for improvement of whole-body counter calibrations. 27 refs., 2 figs., 4 tabs.

Ferro- and antiferro-magnetism in (Np, Pu)BC

NASA Astrophysics Data System (ADS)

Klimczuk, T.; Shick, A. B.; Kozub, A. L.; Griveau, J.-C.; Colineau, E.; Falmbigl, M.; Wastin, F.; Rogl, P.

2015-04-01

Two new transuranium metal boron carbides, NpBC and PuBC, have been synthesized. Rietveld refinements of powder XRD patterns of {Np,Pu}BC confirmed in both cases isotypism with the structure type of UBC. Temperature dependent magnetic susceptibility data reveal antiferromagnetic ordering for PuBC below TN = 44 K, whereas ferromagnetic ordering was found for NpBC below TC = 61 K. Heat capacity measurements prove the bulk character of the observed magnetic transition for both compounds. The total energy electronic band structure calculations support formation of the ferromagnetic ground state for NpBC and the antiferromagnetic ground state for PuBC.

Project Interface Requirements Process Including Shuttle Lessons Learned

NASA Technical Reports Server (NTRS)

Bauch, Garland T.

2010-01-01

Most failures occur at interfaces between organizations and hardware. Processing interface requirements at the start of a project life cycle will reduce the likelihood of costly interface changes/failures later. This can be done by adding Interface Control Documents (ICDs) to the Project top level drawing tree, providing technical direction to the Projects for interface requirements, and by funding the interface requirements function directly from the Project Manager's office. The interface requirements function within the Project Systems Engineering and Integration (SE&I) Office would work in-line with the project element design engineers early in the life cycle to enhance communications and negotiate technical issues between the elements. This function would work as the technical arm of the Project Manager to help ensure that the Project cost, schedule, and risk objectives can be met during the Life Cycle. Some ICD Lessons Learned during the Space Shuttle Program (SSP) Life Cycle will include the use of hardware interface photos in the ICD, progressive life cycle design certification by analysis, test, & operations experience, assigning interface design engineers to Element Interface (EI) and Project technical panels, and linking interface design drawings with project build drawings

A mixed methods investigation into the use of non-technical skills by community and hospital pharmacists.

PubMed

Irwin, A; Weidmann, A E

2015-01-01

Non-technical skills refer to the social and cognitive factors that may influence efficient and safe job performance. Non-technical skills are an important element of patient safety in a variety of health care disciplines, including surgery, anesthesia and nursing. However, the use of non-technical skills in pharmacy practice has not yet been fully assessed. To examine attitudes toward, and use of, non-technical skills by pharmacy personnel. A mixed methods approach was used: An attitude survey explored pharmacy personnel attitudes towards non-technical skills and inter-professional collaboration, with community and hospital pharmacy staff (n = 62). Qualitative interviews were then conducted using the critical incident technique, with community pharmacists (n = 11). The survey results demonstrated differences in the opinions of community and hospital pharmacists on three non-technical skill constructs: team structure, mutual support, and situation monitoring, with community pharmacists reporting significantly more positive attitudes about all three constructs. Both groups reported low levels of collaboration with primary care physicians. The interviews identified five non-technical skills as key elements of successful pharmacist performance from the interview transcripts: teamwork; leadership; task management; situation awareness; decision-making. The survey and interviews identified the non-technical skills that are important to pharmacists. This represents the first step towards the development of a behavioral rating system for training purposes that could potentially improve the non-technical skills of pharmacists and enhance patient safety. Copyright © 2015 Elsevier Inc. All rights reserved.

Pack Cementation Aluminide Coatings on Superalloys: Codeposition of Cr and Reactive Elements (RE). Technical Report 1. Chromium and Reactive Element(RE)- Modified Aluminide Diffusion Coatings on Superalloys: Environmental Testing. Technical Report 2

DTIC Science & Technology

1992-11-01

Godlewska and K. Godlewski, Oxid. Met., 22 (1984) 117. 4. J.E. Restall, U.S. Patent #4,687,684 (1987). 5. P.N. Walsh, in Proceeding of the Fourth...McCarron, N.R. Lindblad, and D. Chatterji, Corrosion, 32 (1976) 476. 34 33. E. Godlewska and K. Godlewski, Oxid. Met., 22 (1984) 117. 34. B. Pieraggi

PREFACE: Proceedings of the 11th European Workshop of the European Microbeam Analysis Society (EMAS) on Modern Developments and Applications in Microbeam Analysis

NASA Astrophysics Data System (ADS)

2010-07-01

This volume of IOP Conference Series: Materials Science and Engineering contains papers from the 11th Workshop of the European Microbeam Analysis Society (EMAS) on Modern Developments and Applications in Microbeam Analysis which took place from 10-14 May 2009 in the Hotel Faltom, Gdynia, Poland. The primary aim of this series of workshops is to assess the state-of-the-art and reliability of microbeam analysis techniques. The workshops also provide a forum where students and young scientists starting out on careers in microbeam analysis can meet and discuss with the established experts. The workshops have a very distinct format comprising invited plenary lectures by internationally recognized experts, poster presentations by the participants and round table discussions on the key topics led by specialists in the field. For this workshop EMAS invited speakers on the following topics: EPMA, EBSD, fast energy-dispersive X-ray spectroscopy, three-dimensional microanalysis, and micro-and nanoanalysis in the natural resources industry. The continuing relevance of the EMAS workshops and the high regard in which they are held internationally can be seen from the fact that 69 posters from 16 countries were on display at the meeting and that the participants came from as far away as Japan and the USA. A number of participants with posters were invited to give short oral presentations of their work in two dedicated sessions. As at previous workshops there was also a special oral session for young scientists. Small cash prizes were awarded for the three best posters and for the best oral presentation by a young scientist. The prize for the best poster went to the contribution by G Tylko, S Dubchak, Z Banach and K Turnau, entitled Monte Carlo simulation for an assessment of standard validity and quantitative X-ray microanalysis in plant. Joanna Wojewoda-Budka of the Institute of Metallurgy and Materials Science, Krakow, received the prize for the best oral presentation by a young scientist for her talk entitled Application of focussed ion beam technique for TEM multilayer materials examination. This volume contains the full texts of 5 of the invited plenary lectures and of 24 papers on related topics originating from the posters presented at the workshop. All the papers have been subjected to peer review by a least two referees. January 2009 Acknowledgements On behalf of the European Microbeam Analysis Society I would like to thank all the invited speakers, session chairs and members of the discussion panels for making the meeting such a great success. Special thanks go to Michal Zelechower and Luc Van't dack who directed the organisation of the workshop giving freely of their time and talents. As was the case for previous workshops, the EMAS board in corpore was responsible for the scientific programme. I am particularly grateful to the exhibiting companies and sustaining members for their generous support of the workshop. In this context I would like particularly to mention: Silesian University of Technology, Gliwice Gdansk University of Technology Polish Society for Microscopy (PTMi), Krakow Polish Academy of Sciences - Materials Science Committee, Warsaw Polish Academy of Sciences - Institute of Metallurgy and Materials Science, Krakow Polish Academy of Sciences - Institute of Physics, Warsaw AGH University of Science and Technology, Krakow Warsaw University of Technology Below is a combined list of the exhibiting companies and sponsors of the workshop: Ametek GmbH (Germany) Blackwell Publishing Ltd (UK) Bruker AXS Microanalysis GmbH (Germany) Cameca SA (France) Carl Zeiss SMT GmbH (Germany) COMEF Aparatura Naukowo-Badawcza (Poland) EU-JRC: Inst. for Transuranium Elements (Germany) FEI Company (The Netherlands) IfG - Institute for Scientific Instruments GmbH (Germany) Jeol (Europe) SAS (France) John Wiley & Sons (UK) Olympus Soft Imaging Solutions GmbH (Germany) Oxford Instruments NanoAnalysis Ltd (UK) Probe Software, Inc. (USA) Roenalytic GmbH (Germany) Target-Messtechnik (Germany) Thermo Fisher Scientific BV (The Netherlands) Clive T Walker EMAS President János L Lábár Research Institute for Technical Physics and Materials Science, HAS, Konkoly-Thege M. u. 29-33, HU-1121 Budapest, Hungary Clive T Walker European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, DE-76125 Karlsruhe, Germany Michal Zelechower Silesian University of Technology, Department of Materials Science, ul. Krasinskiego 8, PL-40019 Katowice, Poland Pawel Zieba Polish Academy of Sciences, Institute of Metallurgy and Materials Science, ul. W. Reymonta 25, PL-30059 Krakow, Poland

The Pioneer Projects - Economical exploration of the solar system

NASA Technical Reports Server (NTRS)

Spahr, J. R.; Hall, C. F.

1975-01-01

The interplanetary Pioneer missions are reviewed in terms of management implications and cost control. The responsibilities, organizational structure, and management practices of the Pioneer Projects are presented. The lines of authority and areas of responsibility of the principal organizational elements supporting the Pioneer missions are identified, and the methods employed for maintaining effective and timely interactions among these elements are indicated. The technical and administrative functions of various organizational elements of the project are described. The management and control of activities prior to and during the hardware procurement phase are described to indicate the basis for obtaining visibility of the technical progress, utilization of resources, and cost performance of the contractors and other institutions supporting the Pioneer projects.

76 FR 68429 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... documentation, U.S. Government and contractor engineering, technical, and logistics personnel support services, and other related elements of logistics support. (iv) Military Department: Navy (USMC) (SDH). (v.... Government and contractor engineering, technical, and logistics personnel [[Page 68432

Calculation of multidimensional potential energy surfaces for even-even transuranium nuclei: systematic investigation of the triaxiality effect on the fission barrier

NASA Astrophysics Data System (ADS)

Chai, Qing-Zhen; Zhao, Wei-Juan; Liu, Min-Liang; Wang, Hua-Lei

2018-05-01

Static fission barriers for 95 even-even transuranium nuclei with charge number Z = 94–118 have been systematically investigated by means of pairing self-consistent Woods-Saxon-Strutinsky calculations using the potential energy surface approach in multidimensional (β 2, γ, β 4) deformation space. Taking the heavier 252Cf nucleus (with the available fission barrier from experiment) as an example, the formation of the fission barrier and the influence of macroscopic, shell and pairing correction energies on it are analyzed. The results of the present calculated β 2 values and barrier heights are compared with previous calculations and available experiments. The role of triaxiality in the region of the first saddle is discussed. It is found that the second fission barrier is also considerably affected by the triaxial deformation degree of freedom in some nuclei (e.g., the Z=112–118 isotopes). Based on the potential energy curves, general trends of the evolution of the fission barrier heights and widths as a function of the nucleon numbers are investigated. In addition, the effects of Woods-Saxon potential parameter modifications (e.g., the strength of the spin-orbit coupling and the nuclear surface diffuseness) on the fission barrier are briefly discussed. Supported by National Natural Science Foundation of China (11675148, 11505157), the Project of Youth Backbone Teachers of Colleges and Universities of Henan Province (2017GGJS008), the Foundation and Advanced Technology Research Program of Henan Province (162300410222), the Outstanding Young Talent Research Fund of Zhengzhou University (1521317002) and the Physics Research and Development Program of Zhengzhou University (32410017)

Analysis on fuel breeding capability of FBR core region based on minor actinide recycling doping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Permana, Sidik; Novitrian,; Waris, Abdul

Nuclear fuel breeding based on the capability of fuel conversion capability can be achieved by conversion ratio of some fertile materials into fissile materials during nuclear reaction processes such as main fissile materials of U-233, U-235, Pu-239 and Pu-241 and for fertile materials of Th-232, U-238, and Pu-240 as well as Pu-238. Minor actinide (MA) loading option which consists of neptunium, americium and curium will gives some additional contribution from converted MA into plutonium such as conversion Np-237 into Pu-238 and it's produced Pu-238 converts to Pu-239 via neutron capture. Increasing composition of Pu-238 can be used to produce fissilemore » material of Pu-239 as additional contribution. Trans-uranium (TRU) fuel (Mixed fuel loading of MOX (U-Pu) and MA composition) and mixed oxide (MOX) fuel compositions are analyzed for comparative analysis in order to show the effect of MA to the plutonium productions in core in term of reactor criticality condition and fuel breeding capability. In the present study, neptunium (Np) nuclide is used as a representative of MAin trans-uranium (TRU) fuel composition as Np-MOX fuel type. It was loaded into the core region gives significant contribution to reduce the excess reactivity in comparing to mixed oxide (MOX) fuel and in the same time it contributes to increase nuclear fuel breeding capability of the reactor. Neptunium fuel loading scheme in FBR core region gives significant production of Pu-238 as fertile material to absorp neutrons for reducing excess reactivity and additional contribution for fuel breeding.« less

77 FR 40026 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-06

... and contractor logistics, Quality Assurance Team support services, engineering and technical support..., engineering and technical support, and other related elements of program support. The estimated cost is $49..., maintenance, or training is Confidential. Reverse engineering could reveal Confidential information...

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

DOT National Transportation Integrated Search

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

Identifying Mental Health Elements among Technical University Students Using Fuzzy Delphi Method

NASA Astrophysics Data System (ADS)

Pua, P. K.; Lai, C. S.; Lee, M. F.

2017-08-01

Mental health is a part of our daily life that is often experienced. As a student, mental health issue often encounters a variety of difficult challenges at the higher education institution. A student with good mental health can handle and cope the normal stress of life, capable work productivity, enhance academic performance and able to make contribute to the community. However, rapidly transformation and changing of society have been impacted on students’ mental health, and it will be deteriorated and negatively impact on students if it absence of preventive controlled. This study aimed to identify the element of mental health among the technical university students. A total of 11 experts were selected to analyze the fuzziness consensus of experts. All collected data was analyzed by using the fuzzy Delphi method and the result shows that there are 4 elements of 8 elements that fulfill the requirement consensus of experts, which threshold value is equal and less than 0.2, the percentage of the expert group is more than 75%. The four elements were depression, anxiety, stress, and fear are often experienced by technical university students. In conclusion, precocious actions have to be taken by university and counseling center, parents and non-government organization in order to mitigate the mental health problem faced by students to improve the quality lifestyle students at the university.

Design Issues for Producing Effective Multimedia Presentations.

ERIC Educational Resources Information Center

Mason, Lisa D.

1997-01-01

Discusses design issues for interactive multimedia. Notes that technical communication instructors must consider navigational aids, the degree of control a user should have, audio cues, color and typographical elements, visual elements, and copyright issues. (RS)

Small sample estimation of the reliability function for technical products

NASA Astrophysics Data System (ADS)

Lyamets, L. L.; Yakimenko, I. V.; Kanishchev, O. A.; Bliznyuk, O. A.

2017-12-01

It is demonstrated that, in the absence of big statistic samples obtained as a result of testing complex technical products for failure, statistic estimation of the reliability function of initial elements can be made by the moments method. A formal description of the moments method is given and its advantages in the analysis of small censored samples are discussed. A modified algorithm is proposed for the implementation of the moments method with the use of only the moments at which the failures of initial elements occur.

Steels For Rolling-Element Bearings

NASA Technical Reports Server (NTRS)

Zaretsky, Erwin V.

1988-01-01

Bearing lives increased by attention to details of processing and applications. NASA technical memorandum discusses selection of steels for long-life rolling-element bearings. After brief review of advances in manufacturing, report discusses effect of cleanliness of bearing material on fatigue in rolling element. Also discusses fracture toughnesses of through-hardened and case-hardened materials.

Technical Elements, Demonstration Projects, and Fiscal Models in Medicaid Managed Care for People with Developmental Disabilities.

ERIC Educational Resources Information Center

Kastner, Theodore A.; Walsh, Kevin K.; Criscione, Teri

1997-01-01

Presents a general model of the structure and functioning of managed care and describes elements (provider networks, fiscal elements, risk estimation, case-mix, management information systems, practice parameters, and quality improvement) critical to people with developmental disabilities. Managed care demonstration projects and a hypothetical…

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

Application of the Rehabilitation Act Section 508 to the NPFC

DOT National Transportation Integrated Search

2001-04-09

This paper provides a brief summary of Section 508 and its associated technical standards in layman's terms. It identifies the elements of the NPFC information technology (IT) that are affected by the technical standards and a brief discussion of how...

Safety Education--An Essential Element of Technical Training

ERIC Educational Resources Information Center

Glazener, Everett R.; Comstock, Thomas W.

1978-01-01

After tracing the background of the safety movement, provisions of recent safety legislation, and the ecological and environmental impact of industrial processes, the author stresses the need for safety education in technical education programs to prepare future employees for industrial safety requirements. (MF)

78 FR 78939 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... Quantity or Quantities of Articles or Services under Consideration for Purchase: C-130J technical, engineering and software support; software updates and patches; familiarization training for Portable Flight... and contractor technical support services; and other related elements of logistics and program support...

International ultraviolet explorer observatory operations

NASA Technical Reports Server (NTRS)

1986-01-01

This volume contains the Final Report for the International Ultraviolet Explorer (IUE) Observatory Operations contract, NAS5-28787. The report summarizes the activities of the IUE Observatory over the 13-month period from November 1985 through November 1986 and is arranged in sections according to the functions specified in the Statement of Work (SOW) of the contract. In order to preserve numerical correspondence between the technical SOW elements specified by the contract and the sections of this report, project management activities (SOW element 0.0.) are reported here in Section 7, following the reports of technical SOW elements 1.0 through 6.0. Routine activities have been summarized briefly whenever possible; statistical compilations, reports, and more lengthy supplementary material are contained in the Appendices.

The pioneer projects: Economical exploration of the solar system

NASA Technical Reports Server (NTRS)

Spahr, J. R.; Hall, C. F.

1975-01-01

The interplanetary Pioneer missions are reviewed in terms of management implications and cost control. The responsibilities, organizational structure, and management practices of the Pioneer Projects are presented. The lines of authority and areas of responsibility of the principal organizational elements supporting the Pioneer missions are identified, and the methods employed for maintaining effective and timely interactions among these elements are indicated. The technical and administrative functions of the various organizational elements of the Pioneer Project Office at Ames Research Center are described in terms of their management responsibilities and interactions with other elements of the Project Office and with external organizations having Pioneer Project responsibilities. The management and control of activities prior to and during the hardware procurement phase are described to indicate the basis for obtaining visibility of the technical progress, utilization of resources, and cost performance of the contractors and other institutions supporting the Pioneer projects.

Satellite power system concept development and evaluation program. Volume 1: Technical assessment summary report

NASA Technical Reports Server (NTRS)

1980-01-01

Candidate satellite power system (SPS) concepts were identified and evaluated in terms of technical and cost factors. A number of alternative technically feasible approaches and system concepts were investigated. A reference system was defined to facilitate economic, environmental, and societal assessments by the Department of Energy. All elements of the reference system were defined including the satellite and all its subsystems, the orbital construction and maintenance bases, all elements of the space transportation system, the ground receiving station, and the associated industrial facilities for manufacturing the required hardware. The reference conclusions and remaining issues are stated for the following topical areas: system definition; energy conversion and power management; power transmission and reception; structures, controls, and materials; construction and operations; and space transportation.

Source-term characterisation and solid speciation of plutonium at the Semipalatinsk NTS, Kazakhstan.

PubMed

Nápoles, H Jiménez; León Vintró, L; Mitchell, P I; Omarova, A; Burkitbayev, M; Priest, N D; Artemyev, O; Lukashenko, S

2004-01-01

New data on the concentrations of key fission/activation products and transuranium nuclides in samples of soil and water from the Semipalatinsk Nuclear Test Site are presented and interpreted. Sampling was carried out at Ground Zero, Lake Balapan, the Tel'kem craters and reference locations within the test site boundary well removed from localised sources. Radionuclide ratios have been used to characterise the source term(s) at each of these sites. The geochemical partitioning of plutonium has also been examined and it is shown that the bulk of the plutonium contamination at most of the sites examined is in a highly refractory, non-labile form.

Sulphursoil - Delano Development Corporation

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1985-06-01

A sizable amount of technical information has been accumulated on the effects of agricultural applications of the natural mineral product called Sul-Fe. This technical information supports the field observations of farmers, landscapers and gardeners who have used the product. Sul-Fe is often evaluated in terms of its sulphur content alone. When compared to elemental sulphur (100% sulphur), the 18 to 21% sulphur content of Sul-Fe seems relatively low. However, as the following technical data indicates, when judged on actual effects, Sul-Fe's complex mixture of minerals has several advantages over elemental sulphur. When judged on the basis of soil acidulation, Sul-Femore » has more immediate effects than elemental sulphur. The rapid acidifying effect is due to Sul-Fe's content of crystalline sulphuric acid. Sul-Fe also has long-term effects on soil pH due to its content of sulphur and sulfides and the time required to oxidize these materials. Elemental sulphur contains sulphur in only one chemical form which must be microbially oxidized before it becomes reactive in the soil solution, a reaction that takes quite some time in some soils. Sul-Fe is thus better than elemental sulphur in terms of immediate effects and comparable in terms of long term effects. Applied blends of Sul-Fe supplemented with elemental sulphur may provide for a maximization of both short and long term effects. An additional benefit derived from the use of Sul-Fe is the addition to the soil of a variety of trace nutrients including iron, calcium, zinc, copper, manganese, magnesium, and molybdenum.« less

Alpha-emitting nuclides in the marine environment

NASA Astrophysics Data System (ADS)

Pentreath, R. J.

1984-06-01

The occurrence of alpha-emitting nuclides and their daughter products in the marine environment continues to be a subject of study for many reasons. Those nuclides which occur naturally, in the uranium, thorium and actinium series, are of interest because of their value in determining the rates of geological and geochemical processes in the oceans. Studies of them address such problems as the determination of rates of transfer of particulate matter, deposition rates, bioturbation rates, and so on. Two of the natural alpha-series nuclides in which a different interest has been expressed are 210Po and 226Ra, because their concentrations in marine organisms are such that they contribute to a significant fraction of the background dose rates sustained both by the organisms themselves and by consumers of marine fish and shellfish. To this pool of naturally-occurring nuclides, human activities have added the transuranium nuclides, both from the atmospheric testing of nuclear devices and from the authorized discharges of radioactive wastes into coastal waters and the deep sea. Studies have therefore been made to understand the chemistry of these radionuclides in sea water, their association with sedimentary materials, and their accumulation by marine organisms, the last of these being of particular interest because the transuranics are essentially "novel" elements to the marine fauna and flora. The need to predict the long-term behaviour of these nuclides has, in turn, stimulated research on those naturally-occurring nuclides which may behave in a similar manner.

Remediation of transuranic-contaminated coral soil at Johnston Atoll using the segmented gate system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bramlitt, E.; Johnson, N.

1994-12-31

Thermo Analytical, Inc. (TMA) has developed a system to remove clean soil from contaminated soil. The system consists of a soil conveyor, an array of radiation detectors toward the conveyor feed end, a gate assembly at the conveyor discharge end, and two additional conveyors which move discharged soil to one or another paths. The gate assembly is as wide as the ``sorter conveyor,`` and it has eight individual gates or segments. The segments automatically open or close depending on the amount of radioactivity present. In one position they pass soil to a clean soil conveyor, and in the other positionmore » they let soil fall to a hot soil conveyor. The soil sorting process recovers clean soil for beneficial use and it substantially reduces the quantity of soil which must be decontaminated or prepared for waste disposal. The Segmented Gate System (SGS) was developed for the cleanup of soil contaminated with some transuranium elements at Johnston Atoll. It has proven to be an effective means for recovering clean soil and verifying that soil is clean, minimizing the quantity of truly contaminated soil, and providing measures of contamination for waste transport and disposal. TMA is constructing a small, transportable soil cleanup as it is confident the SGS technology can be adapted to soils and contaminants other than those at Johnston Atoll. It will use this transportable plant to demonstrate the technology and to develop site specific parameters for use in designing plants to meet cleanup needs.« less

Laser-heating and Radiance Spectrometry for the Study of Nuclear Materials in Conditions Simulating a Nuclear Power Plant Accident.

PubMed

Manara, Dario; Soldi, Luca; Mastromarino, Sara; Boboridis, Kostantinos; Robba, Davide; Vlahovic, Luka; Konings, Rudy

2017-12-14

Major and severe accidents have occurred three times in nuclear power plants (NPPs), at Three Mile Island (USA, 1979), Chernobyl (former USSR, 1986) and Fukushima (Japan, 2011). Research on the causes, dynamics, and consequences of these mishaps has been performed in a few laboratories worldwide in the last three decades. Common goals of such research activities are: the prevention of these kinds of accidents, both in existing and potential new nuclear power plants; the minimization of their eventual consequences; and ultimately, a full understanding of the real risks connected with NPPs. At the European Commission Joint Research Centre's Institute for Transuranium Elements, a laser-heating and fast radiance spectro-pyrometry facility is used for the laboratory simulation, on a small scale, of NPP core meltdown, the most common type of severe accident (SA) that can occur in a nuclear reactor as a consequence of a failure of the cooling system. This simulation tool permits fast and effective high-temperature measurements on real nuclear materials, such as plutonium and minor actinide-containing fission fuel samples. In this respect, and in its capability to produce large amount of data concerning materials under extreme conditions, the current experimental approach is certainly unique. For current and future concepts of NPP, example results are presented on the melting behavior of some different types of nuclear fuels: uranium-plutonium oxides, carbides, and nitrides. Results on the high-temperature interaction of oxide fuels with containment materials are also briefly shown.

IT Labs Proof-of-Concept Project: Technical Data Interoperability (TDI) Pathfinder Via Emerging Standards

NASA Technical Reports Server (NTRS)

Conroy, Mike; Gill, Paul; Ingalls, John; Bengtsson, Kjell

2014-01-01

No known system is in place to allow NASA technical data interoperability throughout the whole life cycle. Life Cycle Cost (LCC) will be higher on many developing programs if action isn't taken soon to join disparate systems efficiently. Disparate technical data also increases safety risks from poorly integrated elements. NASA requires interoperability and industry standards, but breaking legacy ways is a challenge.

Using Finite Element Method to Estimate the Material Properties of a Bearing Cage

DTIC Science & Technology

2018-02-01

UNCLASSIFIED UNCLASSIFIED AD-E403 988 Technical Report ARMET-TR-17035 USING FINITE ELEMENT METHOD TO ESTIMATE THE MATERIAL...TITLE AND SUBTITLE USING FINITE ELEMENT METHOD TO ESTIMATE THE MATERIAL PROPERTIES OF A BEARING CAGE 5a. CONTRACT NUMBER 5b. GRANT...specifications of non-metallic bearing cages are typically not supplied by the manufacturer. In order to setup a finite element analysis of a

2D and 3D Multiscale/Multicomponent Modeling of Impact Response of Heterogeneous Energetic Composites

DTIC Science & Technology

2016-06-01

7 Development of Cohesive Finite Element Method (CFEM) Capability ................................7 3D...Cohesive Finite Element Method (CFEM) framework A new scientific framework and technical capability is developed for the computational analyses of...this section should shift from reporting activities to reporting accomplishments. Development of Cohesive Finite Element Method (CFEM) Capability

Non-technical skills of surgical trainees and experienced surgeons.

PubMed

Gostlow, H; Marlow, N; Thomas, M J W; Hewett, P J; Kiermeier, A; Babidge, W; Altree, M; Pena, G; Maddern, G

2017-05-01

In addition to technical expertise, surgical competence requires effective non-technical skills to ensure patient safety and maintenance of standards. Recently the Royal Australasian College of Surgeons implemented a new Surgical Education and Training (SET) curriculum that incorporated non-technical skills considered essential for a competent surgeon. This study sought to compare the non-technical skills of experienced surgeons who completed their training before the introduction of SET with the non-technical skills of more recent trainees. Surgical trainees and experienced surgeons undertook a simulated scenario designed to challenge their non-technical skills. Scenarios were video recorded and participants were assessed using the Non-Technical Skills for Surgeons (NOTSS) scoring system. Participants were divided into subgroups according to years of experience and their NOTSS scores were compared. For most NOTSS elements, mean scores increased initially, peaking around the time of Fellowship, before decreasing roughly linearly over time. There was a significant downward trend in score with increasing years since being awarded Fellowship for six of the 12 NOTSS elements: considering options (score -0·015 units per year), implementing and reviewing decisions (-0·020 per year), establishing a shared understanding (-0·014 per year), setting and maintaining standards (-0·024 per year), supporting others (-0·031 per year) and coping with pressure (-0·015 per year). The drop in NOTSS score was unexpected and highlights that even experienced surgeons are not immune to deficiencies in non-technical skills. Consideration should be given to continuing professional development programmes focusing on non-technical skills, regardless of the level of professional experience. © 2017 BJS Society Ltd Published by John Wiley & Sons Ltd.

Inventory of available data elements for the San Bernardino, California region

NASA Technical Reports Server (NTRS)

Christenson, J.; Michel, R.

1981-01-01

Elements of data sets that are available to be integrated for the San Bernardino vertical data integration project are given. Each of the data sets has specified for it the ownership, validity, accuracy and technical requirements for integration.

The element of naturalness when evaluating image quality of digital photo documentation after sexual assault.

PubMed

Ernst, E J; Speck, P M; Fitzpatrick, J J

2012-01-01

Digital photography is a valuable adjunct to document physical injuries after sexual assault. In order for a digital photograph to have high image quality, there must exist a high level of naturalness. Digital photo documentation has varying degrees of naturalness; however, for a photograph to be natural, specific technical elements for the viewer must be satisfied. No tool was available to rate the naturalness of digital photo documentation of female genital injuries after sexual assault. The Photo Documentation Image Quality Scoring System (PDIQSS) tool was developed to rate technical elements for naturalness. Using this tool, experts evaluated randomly selected digital photographs of female genital injuries captured following sexual assault. Naturalness of female genital injuries following sexual assault was demonstrated when measured in all dimensions.

A business man views commercial ventures in space.

NASA Technical Reports Server (NTRS)

Scarff, D. D.; Bloom, H. L.

1973-01-01

Paper reviews technical, resource planning and marketing steps an industrial organization must perform in arriving at a decision to undertake space development and production of commercial products or services for Users on the ground. Technical elements are supported by particular examples. Analysis of required resources emphasizes facility and financial inter-relationships between commercial organizations and NASA. Marketing planning covers elements of profitability. Paper addresses questions related to protection of corporate stockholders and public interest, investment decision timing, budget variations. Paper concludes with observations on timeliness of planning shuttle-based commercial ventures and on key industry/NASA problems and decisions.

76 FR 31416 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-31

... ADMINISTRATION 48 CFR Parts 52 and 53 [FAC 2005-52; Item VI; Docket 2011-0078; Sequence 2] Federal Acquisition... publication schedules. Please cite FAC 2005-52, Technical Amendments. SUPPLEMENTARY INFORMATION: In order to update certain elements in 48 CFR parts 52 and 53, this document makes editorial changes to the Federal...

Technical Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project

DTIC Science & Technology

2005-09-30

Technical Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project William R. Metzger Marine...Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

Scientific and Technical Chinese, Volume II. Glossary.

ERIC Educational Resources Information Center

Kao, Kung-yi; And Others

A composite English-to-Chinese glossary of all terms introduced in the individual lessons of "Scientific and Technical Chinese" is presented here. The appendices include lists of weights and measures and chemical elements, and a partial list of Chinese government organizations and research institutes related to science and technology.…

Department of Defense Access to Intellectual Property for Weapon Systems Sustainment

DTIC Science & Technology

2017-05-01

and acquiring technical data rights …  The cost benefit analysis of including a priced contract option for the future delivery of technical data...entail in terms of cost and benefits , while one of the activities to be finalized is the contract-specific technical data elements.66...Virginia 22311-1882 May 2017 Approved for public release; distribution is unlimited. IDA Paper P-8266 Log: H 17-000030 About This Publication This

Finite Element Barotropic Model for the Indian and Western Pacific OceanBasin: Tidal Model Data Comparisons and Sensitivities

DTIC Science & Technology

2018-01-11

From - To) 01/11/2018 Final Technical Report June 01 2016 - Dec 30 2017 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER Finite - Element Barotropic Model...grid finite - element barotropic fully hydrodynamic model in order to understand the shallow-water dynamics of the Indian Ocean and Western Pacific Ocean...dissipative dissipative processes are explored. 15. SUBJECTTERMS finite - element , unstructured grid, barotropic tides, bathymetry, internal tide

Data Element Dictionary: Finance. A Technical Report Concerning Finance Related Data Elements in the WICHE Management Information Systems Program. First Edition.

ERIC Educational Resources Information Center

Thomas, Charles R.

This document is one of the 5 sections of the Data Element Dictionary developed as part of the WICHE Management Information Systems (MIS) Program. The elements in this section apply to both the current and historical data concerning finance. The purpose of the WICHE MIS Program is to make it possible to derive data which will be truly comparable…

Customisation of an instrument to assess anaesthesiologists' non-technical skills.

PubMed

Jepsen, Rikke M H G; Spanager, Lene; Lyk-Jensen, Helle T; Dieckmann, Peter; Østergaard, Doris

2015-02-22

The objectives of the study were to identify Danish anaesthesiologists' non-technical skills and to customise the Scottish-developed Anaesthetists' Non-Technical Skills instrument for Danish anaesthesiologists. Six semi-structured group interviews were conducted with 31 operating room team members: anaes-thesiologists, nurse anaesthetists, surgeons, and scrub nurses. Interviews were transcribed verbatim and analysed using directed content analysis. Anaesthesiologists' non-technical skills were identified, coded, and sorted using the original instrument as a basis. The resulting prototype instrument was discussed with anaesthesiologists from 17 centres to ensure face validity. Interviews lasted 46-67 minutes. Identified examples of anaesthesiologists' good or poor non-technical skills fit the four categories in the original instrument: situation awareness; decision making; team working; and task management. Anaesthesiologists' leadership role in the operating room was emphasised: the original 'Task Management' category was named 'Leadership'. One new element, 'Demonstrating self-awareness' was added under the category 'Situation Awareness'. Compared with the original instrument, half of the behavioural markers were new, which reflected that being aware of and communicating one's own abilities to the team; working systematically; and speaking up to avoid adverse events were important skills. The Anaesthetists' Non-Technical Skills instrument was customised to a Danish setting using the identified non-technical skills for anaesthesiologists and the original instrument as basis. The customised instrument comprises four categories and 16 underpinning elements supported by multiple behavioural markers. Identifying non-technical skills through semi-structured group interviews and analysing them using direct content analysis proved a useful method for customising an assessment instrument to another setting.

PREFACE: EMAS 2011: 12th European Workshop on Modern Developments in Microbeam Analysis

NASA Astrophysics Data System (ADS)

Brisset, François; Dugne, Olivier; Robaut, Florence; Lábár, János L.; Walker, Clive T.

2012-03-01

This volume of IOP Conference Series: Materials Science and Engineering contains papers from the 12th Workshop of the European Microbeam Analysis Society (EMAS) on Modern Developments and Applications in Microbeam Analysis, which took place from the 15-19 May 2011 in the Angers Congress Centre, Angers, France. The primary aim of this series of workshops is to assess the state-of-the-art and reliability of microbeam analysis techniques. The workshops also provide a forum where students and young scientists starting out on a career in microbeam analysis can meet and discuss with the established experts. The workshops have a very specific format comprising invited plenary lectures by internationally recognized experts, poster presentations by the participants and round table discussions on the key topics led by specialists in the field. This workshop was organized in collaboration with GN-MEBA - Groupement National de Microscopie Electronique à Balayage et de microAnalysis, France. The technical programme included the following topics: the limits of EPMA, new techniques, developments and concepts in microanalysis, microanalysis in the SEM, and new and less common applications of micro- and nanoanalysis. As at previous workshops there was also a special oral session for young scientists. The best presentation by a young scientist was awarded with an invitation to attend the 2012 Microscopy and Microanalysis meeting at Phoenix, Arizona. The prize went to Pierre Burdet, of the Federal Institute of Technology of Lausanne (EPFL), for his talk entitled '3D EDS microanalysis by FIB-SEM: enhancement of elemental quantification'. The continuing relevance of the EMAS workshops and the high regard in which they are held internationally can be seen from the fact that 74 posters from 18 countries were on display at the meeting, and that the participants came from as far away as Japan, Canada and the USA. A selection of participants with posters were invited to give a short oral presentation of their work in three dedicated sessions. The prize for the best poster was an invitation to participate in the 22nd Australian Conference on Microscopy and Microanalysis (ACMM 22) at Perth, Western Australia. The prize was awarded to G Samardzija of the Jozef Stefan Institute, Ljubljana, for the poster entitled: 'EPMA-WDS quantitative compositional analysis of barium titanate ceramics doped with cerium'. This proceedings volume contains the full texts of 5 of the invited plenary lectures and of 23 papers on related topics originating from the posters presented at the workshop. All the papers have been subjected to peer review by a least two referees. January 2012 Acknowledgements On behalf of the European Microbeam Analysis Society I would like to thank all the invited speakers, session chairs and members of the discussion panels for making the meeting such a great success. Special thanks go to François Brisset and Luc Van't dack who directed the organisation of the workshop giving freely of their time and talents. As was the case for previous workshops, the EMAS board in corpore was responsible for the scientific programme. The technical exhibition, which occupied 130 sq.m of floor space, was outstanding. It was very encouraging to see new instruments on display, including a FEG electron microprobe as a first worldwide presentation. Moreover, almost all the companies that exhibited provided financial support, either by sponsoring an event or by advertising. Below, in alphabetical order, is a list of exhibiting companies and sponsors of the workshop: Ametek GmbH, Edax Business UnitGN-MEBA Bruker Nano GmbHJeol (Europe) SAS CamecaL'Oréal, Direction Générale Recherche et Innovation Carl Zeiss NTSNanoMEGAS sprl Commissariat à l'Energie AtomiqueOxford Instruments SAS European Institute for Transuranium Elements (Germany)Probe Software, Inc. ElexienceSAMx FEI CompanyTarget-Messtechnik Fondis Electronic SAThermo Fisher Scientific Gatan (France) Clive T. Walker EMAS President

78 FR 59342 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... related elements of logistical and program support. (iv) Military Department: Air Force (QAI) (v) Prior... contractor engineering, technical and logistics support services, and other related elements of logistical and program support. The estimated cost is $60 million. This proposed sale will contribute to the...

Method of Individual Forecasting of Technical State of Logging Machines

NASA Astrophysics Data System (ADS)

Kozlov, V. G.; Gulevsky, V. A.; Skrypnikov, A. V.; Logoyda, V. S.; Menzhulova, A. S.

2018-03-01

Development of the model that evaluates the possibility of failure requires the knowledge of changes’ regularities of technical condition parameters of the machines in use. To study the regularities, the need to develop stochastic models that take into account physical essence of the processes of destruction of structural elements of the machines, the technology of their production, degradation and the stochastic properties of the parameters of the technical state and the conditions and modes of operation arose.

Student Achievement in Identified Workforce Clusters: Understanding Factors that Influence Student Success

ERIC Educational Resources Information Center

D'Amico, Mark M.; Morgan, Grant B.; Robertson, Thashundray C.

2011-01-01

This study blends elements from two South Carolina Technical College System initiatives--Achieving the Dream and a workforce cluster strategy. Achieving the Dream is a national non-profit organization created to help technical and community college students succeed, particularly low-income students and students of color. This initiative, combined…

Engineering an Associate Degree-Level STEM Workforce Education Curriculum

ERIC Educational Resources Information Center

Selwitz, Jason L.; Ahring, Birgitte; Garcia-Perez, Manuel; Morrison, Judith

2018-01-01

Community and technical colleges serve a vital function in STEM education by training workers for medium- and high-skilled technical careers and providing employers the labor necessary to operate and maintain thriving business ventures. A curriculum developed with the elements of a systems-based approach results in a program more relevant to the…

Posters with an artistic flair.

PubMed

Ellerbee, Susan M

2006-01-01

Posters are a popular medium used in the classroom and at conferences. Most published and Internet resources focus on the technical aspects of poster creation. The artist's perspective has rarely been addressed. The author fills that gap by presenting color theory and a balanced appearance as important elements to be considered. Specific technical and artistic considerations are presented.

Examining the Impact of Non-Technical Security Management Factors on Information Security Management in Health Informatics

ERIC Educational Resources Information Center

Imam, Abbas H.

2013-01-01

Complexity of information security has become a major issue for organizations due to incessant threats to information assets. Healthcare organizations are particularly concerned with security owing to the inherent vulnerability of sensitive information assets in health informatics. While the non-technical security management elements have been at…

Measurement of Perceived and Technical Quality of Care for Depression in Racially and Ethnically Diverse Groups.

PubMed

Leff, H Stephen; Chow, Clifton; Wieman, Dow A; Ostrow, Laysha; Cortés, Dharma E; Harris, Treniece

2016-08-01

Measurement of patient satisfaction is now considered essential for providing patient centered care and is an important tool for addressing health care disparities. However, little is known about how ethnically and racially diverse (ERD) groups differ in how they perceive quality, and widely used instruments for measuring perceived quality give little attention to cultural elements of care. This study examined the relationship between the culturally determined beliefs and expectations of four ERD groups (African Americans, Latinos, Portuguese-speakers, and Haitians, total N = 160) and the technical quality of treatment for depression provided in four "culturally-specific" primary care clinics. Using data from the Experiences of Care and Health Outcomes survey, chart reviews and focus groups, the study addressed a set of questions related to the psychometric properties of perceived care measures and the technical quality of care. The groups differed in preferred cultural elements except all preferred inclusion of religion. They did not differ in overall perceived quality. Technical quality was higher for Portuguese and Haitians than for African Americans and Latinos. Implications of group differences for measuring quality are discussed.

Workshop on the Integration of Finite Element Modeling with Geometric Modeling

NASA Technical Reports Server (NTRS)

Wozny, Michael J.

1987-01-01

The workshop on the Integration of Finite Element Modeling with Geometric Modeling was held on 12 May 1987. It was held to discuss the geometric modeling requirements of the finite element modeling process and to better understand the technical aspects of the integration of these two areas. The 11 papers are presented except for one for which only the abstract is given.

The Tolypocladium inflatum CPA element encodes a RecQ helicase-like gene.

PubMed

Kempken, Frank

2008-12-01

Previously, a repetitive CPA element was discovered in the genome of the filamentous fungus Tolypocladium inflatum; however, no further characterization was technically possible at that time. In this study, PCR amplification was used to detect a 4 kb conserved portion of the CPA element that appeared to be present in most, if not all, genomic CPA elements. The amplicons included a large open reading frame that was most similar to a RecQ helicase-like gene from Metarhizium anisopliae. The repetitive nature of the CPA element suggests that it is related to the eukaryotic Helitron class of transposable elements.

Sports Fields: A Manual for Design Construction and Maintenance.

ERIC Educational Resources Information Center

Puhalla, Jim; Krans, Jeff; Goatley, Mike

Comprehensive technical reference information is provided for those responsible for the design, construction, renovation, or maintenance of sports grounds. Chapters illustrate specific design elements of all popular sports facilities, and explain how those elements are integrated in a successful project; explore commonly encountered sports field…

Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results

DTIC Science & Technology

1988-09-01

Test and Evaluation Report Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results by .0 Joseph J...PROGRAM PROJECT TASK WORK UNIT Washington, D.C. 20361 ELEMENT NO. NO. NO. ACCESSION NO. OMN 1820 11. TITLE (Include Security Classification) TEST AND...EVALUATION OF THE NAVY TECHNICAL INFORMATION PRESENTATION SYSTEM (NTIPS) F-14A FIELD TEST RESULTS 12. PERSONAL AUTHOR(S) Fuller, Joseph F. (DTRC) Post

Neuromorphic elements and systems as the basis for the physical implementation of artificial intelligence technologies

NASA Astrophysics Data System (ADS)

Demin, V. A.; Emelyanov, A. V.; Lapkin, D. A.; Erokhin, V. V.; Kashkarov, P. K.; Kovalchuk, M. V.

2016-11-01

The instrumental realization of neuromorphic systems may form the basis of a radically new social and economic setup, redistributing roles between humans and complex technical aggregates. The basic elements of any neuromorphic system are neurons and synapses. New memristive elements based on both organic (polymer) and inorganic materials have been formed, and the possibilities of instrumental implementation of very simple neuromorphic systems with different architectures on the basis of these elements have been demonstrated.

Compilation of Cooperative Data Element Dictionary of Five Federal Agencies’ Systems for Processing of Technical Report Literature

DTIC Science & Technology

1983-03-01

investigator participated with Libary of Congress (LC) Staff and Gov- ernment Printing Office (GPO) catalogers in identifying which data elements...National Standards Institute Standard format, ANSI Z.39-2). This standard includes iden- tif ication of specific data elements by means of 3- digit tags...the closer they can come to efficient exchange. But tags assigned to the core data elements differ: they are all 3- digit tags, but the same 3 digits

14 CFR § 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

14 CFR 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

14 CFR 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

75 FR 51864 - Self-Regulatory Organizations; Municipal Securities Rulemaking Board; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... decisions. Data elements with respect to the SHORT subscription service that would be provided through the... information about technical data elements to support transmission and data-integrity processes between the... for making well-informed investment decisions. Broad access to the information collected by the SHORT...

75 FR 60488 - Self-Regulatory Organizations; Municipal Securities Rulemaking Board; Order Granting Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-30

... decisions. Data elements with respect to the SHORT subscription service that would be provided through the... information about technical data elements to support transmission and data-integrity processes between the... Securities and Exchange Commission (``Commission''), pursuant to Section 19(b)(1) of the Securities [[Page...

DYNALIST II : A Computer Program for Stability and Dynamic Response Analysis of Rail Vehicle Systems : Volume 3. Technical Report Addendum.

DOT National Transportation Integrated Search

1976-07-01

Several new capabilities have been added to the DYNALIST II computer program. These include: (1) a component matrix generator that operates as a 3-D finite element modeling program where elements consist of rigid bodies, flexural bodies, wheelsets, s...

Technical Leadership Development Program

DTIC Science & Technology

2010-12-13

the traditional tenets of leadership and management , systems thinking, understanding SOS issues, and thinking and acting holistically. Our research...international element 2.0 Enterprise Leadership and Management UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 002. TO002, RT 004 Report No...mechanisms for leadership of the overall technical effort, for systems engineering, for requirements, management , and for systems integration. o Develop

A Plan of Organization, Administration, and Elements of Finance for Vocational-Technical Adult Education, Birmingham City School System.

ERIC Educational Resources Information Center

Shelton, John Alton

Designed to help formulate a plan of organization and administration for vocational and technical education and adult education in the Birmingham, Alabama, city schools, this study entailed an extensive literature review on vocational education and administrative matters; a historical review of several Birmingham schools (Paul Hayne School,…

Fiscal Year 1986 Technical Objective Document (TOD).

DTIC Science & Technology

1986-03-01

abilties superior to other IR and manual turrets. - START DATE: FY 88 END DATE: FY 90" PROJECT TITLE: COMPOSITE METAL FIRES EE 62:06 JON: 2673XXXX...TECHNOLOGY: FIRE ELEMENT: INTERACTION DESCRIPTION (TECHNICAL OBJECTIVE) Evaluate a new series of agents "BORALONS" capable of extinguishing metal fires and...PROJECT TITLE: COMPOSITE METAL FIRES PE: 63723 JON: 2104XXXX

NASA Publications Guide for Authors

NASA Technical Reports Server (NTRS)

2015-01-01

This document presents guidelines for use by NASA authors in preparation and publication of their scientific and technical information (STI). Section 2 gives an overview. Section 2 describes types of publication. Section 3 discusses technical, data/information, and dissemination reviews. Section 4 provides recommended standards and gives the elements of a typical report. Section 5 presents miscellaneous preparation recommendations.

Exploring Electrochromics: A Series of Eye-Catching Experiments to Introduce Students to Multidisciplinary Research

ERIC Educational Resources Information Center

Small, Leo J.; Wolf, Steven; Spoerke, Erik D.

2014-01-01

Introducing students to a multidisciplinary research laboratory presents challenges in terms of learning specific technical skills and concepts but also with respect to integrating different technical elements to form a coherent picture of the research. Here we present a multidisciplinary series of experiments we have developed in the Electronic,…

Humanistic Elements in the Educational Practice at a United States Sub-Baccalaureate Technical College

ERIC Educational Resources Information Center

Chen, Peng; Schmidtke, Carsten

2017-01-01

Humanism has never been able to establish a firm place in technical education, which remains predominantly pragmatist in response to industry needs, certification requirements and educational standardisation. However, after a period of decline, humanism has made somewhat of a comeback as part of the movement toward student-centred education.…

Balancing Career and Technical Education with Academic Coursework: The Consequences for Mathematics Achievement in High School

ERIC Educational Resources Information Center

Bozick, Robert; Dalton, Benjamin

2013-01-01

Federal legislation has attempted to move career and technical education (CTE) from a segregated component of the high school curriculum to an integrated element that jointly improves both academic and career readiness. However, concerns remain about the ability of CTE to improve academic learning. Using a nationally representative sample of high…

Elements of Emotional Intelligence that Facilitate Exper-to-Peer Tacit Knowledge Transfer

ERIC Educational Resources Information Center

Berry, Catherine M.

2010-01-01

The purpose of this quantitative study was to compare the emotional intelligence competencies of a group of technical experts with high skills in problem-solving, leadership and mentoring (Group A) with a group of technical experts with lower skills in problem solving, leadership, and mentoring (Group B) at a semiconductor manufacturing factory in…

Adding the Human Element to Ship Manoeuvring Simulations

NASA Astrophysics Data System (ADS)

Aarsæther, Karl Gunnar; Moan, Torgeir

Time-domain simulation of ship manoeuvring has been utilized in risk analysis to assess the effect of changes to the ship-lane, development in traffic volume and the associated risk. The process of ship manoeuvring in a wider socio-technical context consists of the technical systems, operational procedures, the human operators and support functions. Automated manoeuvring simulations without human operators in the simulation loop have often been preferred in simulation studies due to the low time required for simulations. Automatic control has represented the human element with little effort devoted to explain the relationship between the guidance and control algorithms and the human operator which they replace. This paper describes the development and application of a model for the human element for autonomous time-domain manoeuvring simulations. The method is applicable in the time-domain, modular and found to be capable of reproducing observed manoeuvre patterns, but limited to represent the intended behaviour.

Proteomics technique opens new frontiers in mobilome research.

PubMed

Davidson, Andrew D; Matthews, David A; Maringer, Kevin

2017-01-01

A large proportion of the genome of most eukaryotic organisms consists of highly repetitive mobile genetic elements. The sum of these elements is called the "mobilome," which in eukaryotes is made up mostly of transposons. Transposable elements contribute to disease, evolution, and normal physiology by mediating genetic rearrangement, and through the "domestication" of transposon proteins for cellular functions. Although 'omics studies of mobilome genomes and transcriptomes are common, technical challenges have hampered high-throughput global proteomics analyses of transposons. In a recent paper, we overcame these technical hurdles using a technique called "proteomics informed by transcriptomics" (PIT), and thus published the first unbiased global mobilome-derived proteome for any organism (using cell lines derived from the mosquito Aedes aegypti ). In this commentary, we describe our methods in more detail, and summarise our major findings. We also use new genome sequencing data to show that, in many cases, the specific genomic element expressing a given protein can be identified using PIT. This proteomic technique therefore represents an important technological advance that will open new avenues of research into the role that proteins derived from transposons and other repetitive and sequence diverse genetic elements, such as endogenous retroviruses, play in health and disease.

Magnetic Nanofluid Rare Earth Element Extraction Process Report, Techno Economic Analysis, and Results for Geothermal Fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pete McGrail

This GDR submission is an interim technical report and raw data files from the first year of testing on functionalized nanoparticles for rare earth element extraction from geothermal fluids. The report contains Rare Earth Element uptake results (percent removal, mg Rare Earth Element/gram of sorbent, distribution coefficient) for the elements of Neodymium, Europium, Yttrium, Dysprosium, and Cesium. A detailed techno economic analysis is also presented in the report for a scaled up geothermal rare earth element extraction process. All rare earth element uptake testing was done on simulated geothermal brines with one rare earth element in each brine. The raremore » earth element uptake testing was conducted at room temperature.« less

United States Transuranium and Uranium Registries. Annual Report, October 1, 1993--September 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.; Harwick, L.A.

1995-08-01

This report summarizes the salient activities and progress of the United States Transuranium. and Uranium Registries for the period October 1, 1993 through September 30, 1994, along with details of specific programs areas including the National Human Radiobiology Tissue Repository (NHRTR) and tissue radiochemistry analysis project. Responsibility for tissue radioanalysis was transferred from Los Alamos National Laboratory to Washington State University in February 1994. The University of Washington was selected as the Quality Assurance/Quality Control laboratory and a three way intercomparison with them and LANL has been initiated. The results of the initial alpha spectrometry intercomparison showed excellent agreement amongmore » the laboratories and are documented in full in the Appendices to the report. The NHRTR serves as the initial point of receipt for samples received from participants in the USTUR program. Samples are weighed, divided, and reweighed, and a portion retained by the NHRTR as backup or for use in other studies. Tissue specimens retained in the NHRTR are maintained frozen at -70 C and include not only those from USTUR registrants but also those from the radium dial painter and thorium worker studies formerly conducted by Argonne National Laboratory. In addition, there are fixed tissues and a large collection of histopathology slides from all the studies, plus about 20,000 individual solutions derived from donated tissues. These tissues and tissue related materials are made available to other investigators for legitimate research purposes. Ratios of the concentration of actinides in various tissues have been used to evaluate the biokinetics, and retention half times of plutonium and americium. Retention half times for plutonium in various soft tissues range from 10-20 y except for the testes for which a retention half time of 58 y was observed. For americium, the retention half time in various soft tissues studied was 2.2-3.5 y.« less

Engineering directorate technical facilities catalog

NASA Technical Reports Server (NTRS)

Maloy, Joseph E.

1993-01-01

The Engineering Directorate Technical Facilities Catalog is designed to provide an overview of the technical facilities available within the Engineering Directorate at the National Aeronautics and Space Administration (NASA), Lyndon B. Johnson Space Center (JSC) in Houston, Texas. The combined capabilities of these engineering facilities are essential elements of overall JSC capabilities required to manage and perform major NASA engineering programs. The facilities are grouped in the text by chapter according to the JSC division responsible for operation of the facility. This catalog updates the facility descriptions for the JSC Engineering Directorate Technical Facilities Catalog, JSC 19295 (August 1989), and supersedes the Engineering Directorate, Principle test and Development Facilities, JSC, 19962 (November 1984).

Mechanisms of neptunium redox reactions in nitric acid solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chatterjee, Sayandev; Bryan, Samuel A.; Casella, Amanda J.

First transuranium element neptunium (Np) exhibits complicated behavior in acidic solutions because it can adopt wide range of oxidation states typically from +3 to +6 and coordinate large variety of ligands. In particular, accurate determination of Np redox potentials in nitric acid solutions is challenging due to overlapping chemical and electrochemical reactions leading to significant experimental uncertainties. Furthermore, over past decades spectrophotometry has been extensively applied to identify and characterize Np solution species in different oxidation states. However, relevant spectral database of Np in nitric acid solutions that can serve for the reference purposes has yet to be established duemore » to the experimental difficulty to isolate and stabilize Np species in pure oxidation states without compromising solution optical properties. This work demonstrates that combination of voltammetry and controlled-potential in situ thin-layer spectropotentiometry overcomes these challenges so that Np species in pure +3, +4, +5, or +6 oxidation states were electrochemically generated in the systematically varied 0.1 – 5 M nitric acid solutions, and corresponding vis-NIR spectral signatures were obtained. In situ optical monitoring of the interconversion between adjacent Np oxidation states resulted in elucidation of the mechanisms of the involved redox reactions, in-depth understanding of the relative stability of the Np oxidation states, and allowed benchmarking of the redox potentials of the NpO22+/NpO2+, NpO2+/Np4+ and Np4+/Np3+ couples. Notably, the NpO2+/Np4+ couple was distinguished from the proximal Np4+/Np3+ process overcoming previous concerns and challenges encountered in accurate determination of the respective potentials.« less

Laser-heating and Radiance Spectrometry for the Study of Nuclear Materials in Conditions Simulating a Nuclear Power Plant Accident

PubMed Central

Manara, Dario; Soldi, Luca; Mastromarino, Sara; Boboridis, Kostantinos; Robba, Davide; Vlahovic, Luka; Konings, Rudy

2017-01-01

Major and severe accidents have occurred three times in nuclear power plants (NPPs), at Three Mile Island (USA, 1979), Chernobyl (former USSR, 1986) and Fukushima (Japan, 2011). Research on the causes, dynamics, and consequences of these mishaps has been performed in a few laboratories worldwide in the last three decades. Common goals of such research activities are: the prevention of these kinds of accidents, both in existing and potential new nuclear power plants; the minimization of their eventual consequences; and ultimately, a full understanding of the real risks connected with NPPs. At the European Commission Joint Research Centre's Institute for Transuranium Elements, a laser-heating and fast radiance spectro-pyrometry facility is used for the laboratory simulation, on a small scale, of NPP core meltdown, the most common type of severe accident (SA) that can occur in a nuclear reactor as a consequence of a failure of the cooling system. This simulation tool permits fast and effective high-temperature measurements on real nuclear materials, such as plutonium and minor actinide-containing fission fuel samples. In this respect, and in its capability to produce large amount of data concerning materials under extreme conditions, the current experimental approach is certainly unique. For current and future concepts of NPP, example results are presented on the melting behavior of some different types of nuclear fuels: uranium-plutonium oxides, carbides, and nitrides. Results on the high-temperature interaction of oxide fuels with containment materials are also briefly shown. PMID:29286382

Catalysis and biocatalysis program

NASA Technical Reports Server (NTRS)

1991-01-01

The annual report presents the fiscal year (FY) 1990 research activities and accomplishments for the Catalysis and Biocatalysis Program of the Advanced Industrial Concepts Division (AICD), Office of Industrial Technologies of the Department of Energy (DOE). The mission of the AICD is to create a balanced program of high risk, long term, directed interdisciplinary research and development that will improve energy efficiency and enhance fuel flexibility in the industrial sector. The Catalysis and Biocatalysis Program's technical activities were organized into five work elements: the Molecular Modeling and Catalysis by Design element; the Applied Microbiology and Genetics element; the Bioprocess Engineering element; the Separations and Novel Chemical Processes element; and the Process Design and Analysis element.

A CW Gunn Diode Switching Element.

ERIC Educational Resources Information Center

Hurtado, Marco; Rosenbaum, Fred J.

As part of a study of the application of communication satellites to educational development, certain technical aspects of such a system were examined. A current controlled bistable switching element using a CW Gunn diode is reported on here. With modest circuits switching rates of the order of 10 MHz have been obtained. Switching is initiated by…

Edwin M. McMillan, Neptunium, Phase Stability, and the Synchrotron

Science.gov Websites

Elements) * McMillan in LBNL History Edwin M. McMillan Courtesy of Lawrence Berkeley National Laboratory Elements: Early History (Nobel Lecture), DOE Technical Report Download Adobe PDF Reader , December 1951 1907 - 1991, National Academy of Sciences Oral History Transcript -- Dr. Edwin McMillan, American

10 CFR Appendix I to Part 110 - Illustrative List of Reprocessing Plant Components Under NRC Export Licensing Authority

Code of Federal Regulations, 2010 CFR

2010-01-01

... transuranic elements. Different technical processes can accomplish this separation. However, over the years Purex has become the most commonly used and accepted process. Purex involves the dissolution of... facilities have process functions similar to each other, including: irradiated fuel element chopping, fuel...

Reference Manual for Machine-Readable Bibliographic Descriptions.

ERIC Educational Resources Information Center

Martin, M. D., Comp.

UNESCO, in cooperation with several other organizations, has produced a manual, the scope and purpose of which has been to define, for most types of scientific and technical literature, a set of data elements which will constitute an adequate bibliographic citation, and to define the representation of these data elements as they should appear in a…

Assessment of international reference materials for isotope-ratio analysis (IUPAC Technical Report)

USGS Publications Warehouse

Brand, Willi A.; Coplen, Tyler B.; Vogl, Jochen; Rosner, Martin; Prohaska, Thomas

2014-01-01

Since the early 1950s, the number of international measurement standards for anchoring stable isotope delta scales has mushroomed from 3 to more than 30, expanding to more than 25 chemical elements. With the development of new instrumentation, along with new and improved measurement procedures for studying naturally occurring isotopic abundance variations in natural and technical samples, the number of internationally distributed, secondary isotopic reference materials with a specified delta value has blossomed in the last six decades to more than 150 materials. More than half of these isotopic reference materials were produced for isotope-delta measurements of seven elements: H, Li, B, C, N, O, and S. The number of isotopic reference materials for other, heavier elements has grown considerably over the last decade. Nevertheless, even primary international measurement standards for isotope-delta measurements are still needed for some elements, including Mg, Fe, Te, Sb, Mo, and Ge. It is recommended that authors publish the delta values of internationally distributed, secondary isotopic reference materials that were used for anchoring their measurement results to the respective primary stable isotope scale.

Proof of concept of an artificial muscle: theoretical model, numerical model, and hardware experiment.

PubMed

Haeufle, D F B; Günther, M; Blickhan, R; Schmitt, S

2011-01-01

Recently, the hyperbolic Hill-type force-velocity relation was derived from basic physical components. It was shown that a contractile element CE consisting of a mechanical energy source (active element AE), a parallel damper element (PDE), and a serial element (SE) exhibits operating points with hyperbolic force-velocity dependency. In this paper, the contraction dynamics of this CE concept were analyzed in a numerical simulation of quick release experiments against different loads. A hyperbolic force-velocity relation was found. The results correspond to measurements of the contraction dynamics of a technical prototype. Deviations from the theoretical prediction could partly be explained by the low stiffness of the SE, which was modeled analog to the metal spring in the hardware prototype. The numerical model and hardware prototype together, are a proof of this CE concept and can be seen as a well-founded starting point for the development of Hill-type artificial muscles. This opens up new vistas for the technical realization of natural movements with rehabilitation devices. © 2011 IEEE

Development of a system for monitoring technical state of the equipment of a cogeneration steam turbine unit

NASA Astrophysics Data System (ADS)

Aronson, K. E.; Brodov, Yu. M.; Novoselov, V. B.

2012-12-01

Generalized results from the work on developing elements of a comprehensive system for monitoring technical state of the equipment of cogeneration turbines are presented. The parameters of the electrohydraulic turbine control system are considered together with a number of problems concerned with assessing the state of condensers and delivery water heaters.

A Look at Leadership: An Examination of Career and Technical Administrator Preparation in the United States

ERIC Educational Resources Information Center

Clark, Robert W.; Cole, Belinda

2015-01-01

The study is designed to examine the perceptions of U.S. State Directors of Career and Technical Education (CTE) of the state of administrator preparation programs and the needs for training administrators in CTE. The study used descriptive survey research with a 59 element Likert-type questionnaire. The results of the study, from 26 respondents…

An Error Analysis for the Finite Element Method Applied to Convection Diffusion Problems.

DTIC Science & Technology

1981-03-01

D TFhG-]NOLOGY k 4b 00 \\" ) ’b Technical Note BN-962 AN ERROR ANALYSIS FOR THE FINITE ELEMENT METHOD APPLIED TO CONVECTION DIFFUSION PROBLEM by I...Babu~ka and W. G. Szym’czak March 1981 V.. UNVI I Of- ’i -S AN ERROR ANALYSIS FOR THE FINITE ELEMENT METHOD P. - 0 w APPLIED TO CONVECTION DIFFUSION ...AOAO98 895 MARYLAND UNIVYCOLLEGE PARK INST FOR PHYSICAL SCIENCE--ETC F/G 12/I AN ERROR ANALYIS FOR THE FINITE ELEMENT METHOD APPLIED TO CONV..ETC (U

Supersonics Project: Airport Noise Technical Challenge

NASA Technical Reports Server (NTRS)

Bridges, James E.

2008-01-01

This presentation gives an overview of the work being done under the Airport Noise Technical Challenge portion of the Supersonics Project in the Fundamental Aeronautics Program. The objective of the Challenge is to provide technology (e.g. low noise nozzle concepts) and engineering tools required for a viable supersonic aircraft. To accomplish this we have activities divided into Prediction, Diagnostics, and Engineering elements. Each of the tasks reviewed here have potential applications to work being done at other flight regimes and other aircraft and are of interest to the Acoustics Technical Working Group.

Approaches to simulate impact damages on aeronautical composite structures

NASA Astrophysics Data System (ADS)

Sanga, R. P. Lemanle; Garnier, C.; Pantalé, O.

2018-02-01

Impact damage is one of the most critical aggressions for composite structures in aeronautical applications. Consequences of a high/low velocity and high/low energy impacts are very important to investigate. It is usually admitted that the most critical configuration is the Barely Visible Impact Damage (BVID), with impact energy of about 25 J, where some internal damages, invisible on the impacted surface of the specimen, drastically reduce the residual properties of the impacted material. In this work we highlight by the finite element simulation, the damage initiation and propagation process and the size of the defaults created by low velocity impact. Two approaches were developed: the first one is the layup technic and the second one is based on the cohesive element technic. Both technics show the plies damages by the Hashin's criteria. Moreover the second one gives the delamination damages with regards to the Benzeggah-Kenane criteria. The validation of these models is done by confrontation with some experimental results.

Boiler-turbine life extension

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natzkov, S.; Nikolov, M.

1995-12-01

The design life of the main power equipment-boilers and turbines is about 105 working hours. The possibilities for life extension are after normatively regulated control tests. The diagnostics and methodology for Boilers and Turbines Elements Remaining Life Assessment using up to date computer programs, destructive and nondestructive control of metal of key elements of units equipment, metal creep and low cycle fatigue calculations. As well as data for most common damages and some technical decisions for elements life extension are presented.

Application of a boundary element method to the study of dynamical torsion of beams

NASA Technical Reports Server (NTRS)

Czekajski, C.; Laroze, S.; Gay, D.

1982-01-01

During dynamic torsion of beam elements, consideration of nonuniform warping effects involves a more general technical formulation then that of Saint-Venant. Nonclassical torsion constants appear in addition to the well known torsional rigidity. The adaptation of the boundary integral element method to the calculation of these constants for general section shapes is described. The suitability of the formulation is investigated with some examples of thick as well as thin walled cross sections.

36 CFR Appendix D to Part 1191 - Technical

Code of Federal Regulations, 2014 CFR

2014-07-01

... inch (13 mm) high shall be ramped, and shall comply with 405 or 406. 304Turning Space 304.1General... ground space allows a parallel approach to an element and the side reach is unobstructed, the high side....2Obstructed High Reach. Where a clear floor or ground space allows a parallel approach to an element and the...

Proceedings of the 4th Annual Workshop: Advances in Smart Materials for Aerospace Applications

NASA Technical Reports Server (NTRS)

Hardy, Robin C. (Editor); Simpson, Joycelyn O. (Editor)

1996-01-01

The objective of the Fourth Annual Conference on Advances in Smart Materials for Aerospace Applications was to provide a forum for technical dialogue on numerous topics in the area of smart materials. The proceedings presented herein represent the technical contributions of the participants of the workshop. Topics addressed include shape memory alloys, ferroelectrics, fiber optics, finite element simulation, and active control.

Clean Cities Technical Assistance Project (Tiger Teams)

DOE Office of Scientific and Technical Information (OSTI.GOV)

This two-page fact sheet describes Clean Cities' technical assistance (Tiger Teams) capabilities and projects, both completed and ongoing. Tiger Teams are a critical element of the Clean Cities program, providing on-the-ground consultation to help inform program strategies. The knowledge Tiger Team experts gain from these experiences often helps inform other alternative fuels activities, such as needed research, codes and standards revisions, and new training resources.

A Study of Placing Army Requirements on Contract

DTIC Science & Technology

2016-04-01

perhaps being unable to control the external environment, has management authority over business and technical aspects of a specific program. The PM...research is the last element of the planning phase addressing both business and technical considerations. The acquisition team equips themselves with...report is the final product utilizing documented findings and supports the business strategy (DoD, Guidebook for the Acquisition of Services, 2011

Proteomics technique opens new frontiers in mobilome research

PubMed Central

Davidson, Andrew D.; Matthews, David A.

2017-01-01

ABSTRACT A large proportion of the genome of most eukaryotic organisms consists of highly repetitive mobile genetic elements. The sum of these elements is called the “mobilome,” which in eukaryotes is made up mostly of transposons. Transposable elements contribute to disease, evolution, and normal physiology by mediating genetic rearrangement, and through the “domestication” of transposon proteins for cellular functions. Although ‘omics studies of mobilome genomes and transcriptomes are common, technical challenges have hampered high-throughput global proteomics analyses of transposons. In a recent paper, we overcame these technical hurdles using a technique called “proteomics informed by transcriptomics” (PIT), and thus published the first unbiased global mobilome-derived proteome for any organism (using cell lines derived from the mosquito Aedes aegypti). In this commentary, we describe our methods in more detail, and summarise our major findings. We also use new genome sequencing data to show that, in many cases, the specific genomic element expressing a given protein can be identified using PIT. This proteomic technique therefore represents an important technological advance that will open new avenues of research into the role that proteins derived from transposons and other repetitive and sequence diverse genetic elements, such as endogenous retroviruses, play in health and disease. PMID:28932623

Feasibility study of an Integrated Program for Aerospace vehicle Design (IPAD). Volume 1B: Concise review

NASA Technical Reports Server (NTRS)

Miller, R. E., Jr.; Southall, J. W.; Kawaguchi, A. S.; Redhed, D. D.

1973-01-01

Reports on the design process, support of the design process, IPAD System design catalog of IPAD technical program elements, IPAD System development and operation, and IPAD benefits and impact are concisely reviewed. The approach used to define the design is described. Major activities performed during the product development cycle are identified. The computer system requirements necessary to support the design process are given as computational requirements of the host system, technical program elements and system features. The IPAD computer system design is presented as concepts, a functional description and an organizational diagram of its major components. The cost and schedules and a three phase plan for IPAD implementation are presented. The benefits and impact of IPAD technology are discussed.

Automated array assembly task, phase 1

NASA Technical Reports Server (NTRS)

Carbajal, B. G.

1977-01-01

An assessment of state-of-the-art technologies that are applicable to silicon solar cell and solar cell module fabrication is provided. The assessment consists of a technical feasibility evaluation and a cost projection for high-volume production of silicon solar cell modules. The cost projection was approached from two directions; a design-to-cost analysis assigned cost goals to each major process element in the fabrication scheme, and a cost analysis built up projected costs for alternate technologies for each process element. A technical evaluation was used in combination with the cost analysis to identify a baseline low cost process. A novel approach to metal pattern design based on minimum power loss was developed. These design equations were used as a tool in the evaluation of metallization technologies.

NASA Technical Standards Program

NASA Technical Reports Server (NTRS)

Gill, Paul S.; Vaughan, William W.; Parker, Nelson C. (Technical Monitor)

2002-01-01

The NASA Technical Standards Program was officially established in 1997 as result of a directive issued by the Administrator. It is responsible for Agency wide technical standards development, adoption (endorsement), and conversion of Center-unique standards for Agency wide use. One major element of the Program is the review of NSA technical standards products and replacement with non-Government Voluntary Consensus Standards in accordance with directions issued by the Office of Management and Budget. As part of the Program's function, it developed a NASA Integrated Technical Standards Initiative that consists of and Agency wide full-text system, standards update notification system, and lessons learned-standards integration system. The Program maintains a 'one stop-shop' Website for technical standards ad related information on aerospace materials, etc. This paper provides information on the development, current status, and plans for the NAS Technical Standards Program along with metrics on the utility of the products provided to both users within the nasa.gov Domain and the Public Domain.

NASA Technical Standards Program

NASA Technical Reports Server (NTRS)

Gill, Paul S.; Vaughan, WIlliam W.

2003-01-01

The NASA Technical Standards Program was officially established in 1997 as result of a directive issued by the Administrator. It is responsible for Agency wide technical standards development, adoption (endorsement), and conversion of Center-unique standards for Agency wide use. One major element of the Program is the review of NSA technical standards products and replacement with non-Government Voluntary Consensus Standards in accordance with directions issued by the Office of Management and Budget. As part of the Program s function, it developed a NASA Integrated Technical Standards Initiative that consists of and Agency wide full-text system, standards update notification system, and lessons learned - standards integration system. The Program maintains a "one stop-shop" Website for technical standards ad related information on aerospace materials, etc. This paper provides information on the development, current status, and plans for the NAS Technical Standards Program along with metrics on the utility of the products provided to both users within the nasa.gov Domain and the Public Domain.

Synthesis, Crystal Chemistry, and Physical Properties of Ternary Intermetallic Compounds An2T2X( An=Pu, Am; X=ln, Sn; T=Co, Ir, Ni, Pd, Pt, Rh)

NASA Astrophysics Data System (ADS)

Pereira, L. C. J.; Wastin, F.; Winand, J. M.; Kanellakopoulos, B.; Rebizant, J.; Spirlet, J. C.; Almeida, M.

1997-11-01

The synthesis, structural, and physical characterization of nine new ternary intermetallic compounds belonging to the isostructural An2T2Xfamily with the transuranium Pu and Am elements, namely, Pu 2Ni 2In, Pu 2Pd 2In, Pu 2Pt 2In, Pu 2Rh 2In, Pu 2Ni 2Sn, Pu 2Pd 2Sn, Pu 2Pt 2Sn, Am 2Ni 2Sn, and Am 2Pd 2Sn, are reported. From these compounds only Pu 2Rh 2In, Am 2Ni 2Sn, and Am 2Pd 2Sn melt incongruently. All of these compounds crystallize in a tetragonal U 3Si 2-type structure, with the space group P4/ mbm, ( Z=2) as most of the U and Np 2-2-1 compounds already found. In this structure, Anatoms occupy the 4 h( x1, x1+0.5, 0.5), Tthe 4 g( x2, x2+0.5, 0), and Xthe 2 a(0, 0, 0) positions. The average values of x1and x2are, respectively, 0.17 and 0.37. Single-crystal X-ray data were refined to R/ RW=0.045/0.066, 0.043/0.072, 0.066/0.080, 0.070/0.098, 0.029/0.048, 0.055/0.080, 0.073/0.096, 0.048/0.086, 0.048/0.065 for Pu 2Ni 2In, Pu 2Pd 2In, Pu 2Pt 2In, Pu 2Rh 2In, Pu 2Ni 2Sn, Pu 2Pd 2Sn, Pu 2Pt 2Sn, Am 2Ni 2Sn, and Am 2Pd 2Sn, respectively, for seven variables. The variation of the lattice parameters and the range of stability of the 2-2-1 phase are discussed in terms of the substitution of different An(actinide), T(transition metal), and X( p-electron) elements in their crystal structure. The possible role of spin fluctuations in the low-temperature behavior of the Pu samples is indicated by magnetic and electrical resistivity measurements.

Commissioning and first tests of the MAGIC telescope

NASA Astrophysics Data System (ADS)

Baixeras, C.; Bastieri, D.; Bigongiari, C.; Blanch, O.; Blanchot, G.; Bock, R.; Bretz, T.; Chilingarian, A.; Coarasa, J. A.; Colombo, E.; Contreras, J. C.; Corti, D.; Cortina, J.; Domingo, C.; Domingo, E.; Ferenc, D.; Fernández, E.; Flix, J.; Fonseca, V.; Font, L.; Galante, N.; Gaug, M.; Garczarczyk, M.; Gebauer, J.; Giller, M.; Goebel, F.; Hengstebeck, T.; Jacone, P.; de Jager, O. C.; Kalekin, O.; Kestel, M.; Kneiske, T.; Laille, A.; López, M.; López, J.; Lorenz, E.; Mannheim, K.; Mariotti, M.; Martínez, M.; Mase, K.; Merck, M.; Meucci, M.; Miralles, L.; Mirzoyan, R.; Moralejo, A.; Wilhelmi, E. Oña; Orduña, R.; Paneque, D.; Paoletti, R.; Pascoli, D.; Pavel, N.; Pegna, R.; Peruzzo, L.; Piccioli, A.; Roberts, A.; Reyes, R.; Saggion, A.; Sánchez, A.; Sartori, P.; Scalzotto, V.; Schweizer, T.; Sillanpaa, A.; Sobczynska, D.; Stamerra, A.; Stepanian, A.; Stiehler, R.; Takalo, L.; Teshima, M.; Tonello, N.; Torres, A.; Turini, N.; Vitale, V.; Volkov, S.; Wagner, R. M.; Wibig, T.; Wittek, W.

2004-02-01

Major Atmospheric Gamma Imaging Cherenkov telescope is starting its operations with a set of engineering runs to tune the telescope subsystem elements to be ready for the first physics campaign. Many technical improvements have been developed and implemented in several elements of the telescope to reach the lowest energy threshold ever obtained by an Imaging Atmospheric Cherenkov Telescope. A general description of the telescope is presented. The commissioning of the telescope's elements is described and the expected performances are reviewed with the final detector set-up.

CLARIFY (Trademark): An On-Line Guide for Revising Technical Prose,

DTIC Science & Technology

1983-11-01

it appears that writers nominalize in an unconscious attempt to make their prose sound significant. Sociolinguistic studies consistently show that...technical information more effectively than a varied mix of long and short sentences. And there are no empirical studies to suggest that varied sentence...earlier studies , especially those that contrast memory and comprehension - 18 - topic" and "agent." New instance,;--that is, elements of new sentences

Cross-Validation of Predictor Equations for Armor Crewman Performance

DTIC Science & Technology

1980-01-01

Technical Report 447 CROSS-VALIDATION OF PREDICTOR EQUATIONS FOR ARMOR CREWMAN PERFORMANCE Anthony J. Maitland , Newell K. Eaton, and Janet F. Neft...ORG. REPORT NUMBER Anthony J/ Maitland . Newell K/EatorV. and B OTATO RN UBR. 9- PERFORMING ORGANIZATION NAME AND ADDRESS I0. PROGRAM ELEMENT, PROJECT...Technical Report 447 CROSS-VALIDATION OF PREDICTOR EQUATIONS FOR ARMOR CREWMAN PERFORMANCE Anthony J. Maitland , Newell K. Eaton, Accession For and

Building Communities of Engineers to Share Technical Expertise

NASA Technical Reports Server (NTRS)

Topousis, Daria E.; Dennehy, Cornelius J.; Fesq, Lorraine M.

2012-01-01

Developed by the core community to describe our vision of an approach to ensure a sufficiently technically advanced and affordable AR&D technology base is available to support future NASA missions. The goal of this strategy is to create an environment exploiting reusable technology elements for an AR&D system design and development process which is: a) Lower-Risk. b) More Versatile/Scalable. c) Reliable & Crew-Safe. d) More Affordable.

Life as a NATO Engineer

DTIC Science & Technology

2010-08-01

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND...management; leads military in case of specialized survey; supervises more than 25 local civilian employees ; acts as technical expert during contract...Security Assistance Force Head- quarters Camp. I knew I could handle the job of project manager, but wondered about acting as contract manager, technical ex

Issues for Active State Management of the JTPA Title III Grant: A Guide for State Planners and Managers.

ERIC Educational Resources Information Center

Reesman, Cilla J.

This technical assistance guide presents the various options available to state planners and managers in considering five elements of active grant management. Each element is treated in a separate chapter. Chapter 1 addresses issues surrounding the setting of policies that ensure that Title III grants complement state agendas. Chapter 2 concerns…

You Can't Kill a Wasp with a Postage Stamp, or How to Teach 'Em to Pass Element Nine.

ERIC Educational Resources Information Center

Harden, Heather

For student radio broadcasters to acquire a third class operators permit, they must pass Element 9 of the Federal Communications Commission exam. A course was designed to help these amateurs acquire such technical competencies as meter reading, metric conversions, and familiarity with directional antennas. This course description includes a list…

Comparison of the Audio and Video Elements of Instructional Films; (Rapid Mass Learning). Technical Report.

ERIC Educational Resources Information Center

Nelson, H. E.; And Others

Two experiments which compare the effectiveness of the auditory and visual elements in instructional films in order to study their relative contributions to learning are described in this paper. Two films dealing with aerodynamics were used in one experiment, and one film dealing with desert survival was used in the other. Multiple choice item…

A Developmental Study of the Criteria Used by Children to Justify their Affective Response to Arts Experiences.

ERIC Educational Resources Information Center

Murphy, Dennis T.

An empirical study of the way children talk about art experiences is described and the meaning of this talk in terms of the cognition it represents is investigated. The criteria serving as the basis for creation of content analysis categories are subject matter, sensory elements, formal properties, technical competence, expressive elements,…

Optimising technical skills and physical loading in small-sided basketball games.

PubMed

Klusemann, Markus J; Pyne, David B; Foster, Carl; Drinkwater, Eric J

2012-01-01

Differences in physiological, physical, and technical demands of small-sided basketball games related to the number of players, court size, and work-to-rest ratios are not well characterised. A controlled trial was conducted to compare the influence of number of players (2v2/4v4), court size (half/full court) and work-to-rest ratios (4x2.5 min/2x5 min) on the demands of small-sided games. Sixteen elite male and female junior players (aged 15-19 years) completed eight variations of a small-sided game in randomised order over a six-week period. Heart rate responses and rating of perceived exertion (RPE) were measured to assess the physiological load. Movement patterns and technical elements were assessed by video analysis. There were ∼60% more technical elements in 2v2 and ∼20% more in half court games. Heart rate (86 ± 4% & 83 ± 5% of maximum; mean ± SD) and RPE (8 ± 2 & 6 ± 2; scale 1-10) were moderately higher in 2v2 than 4v4 small-sided games, respectively. The 2v2 format elicited substantially more sprints (36 ±12%; mean ±90% confidence limits) and high intensity shuffling (75 ±17%) than 4v4. Full court games required substantially more jogging (9 ±6%) compared to half court games. Fewer players in small-sided basketball games substantially increases the technical, physiological and physical demands.

Dimensioning appropriate technical and economic parameters of elements in urban distribution power nets based on discrete fast marching method

NASA Astrophysics Data System (ADS)

Afanasyev, A. P.; Bazhenov, R. I.; Luchaninov, D. V.

2018-05-01

The main purpose of the research is to develop techniques for defining the best technical and economic trajectories of cables in urban power systems. The proposed algorithms of calculation of the routes for laying cables take into consideration topological, technical and economic features of the cabling. The discrete option of an algorithm Fast marching method is applied as a calculating tool. It has certain advantages compared to other approaches. In particular, this algorithm is cost-effective to compute, therefore, it is not iterative. Trajectories of received laying cables are considered as optimal ones from the point of view of technical and economic criteria. They correspond to the present rules of modern urban development.

04/02/2013 Memorandum

EPA Pesticide Factsheets

Memo about the proposal to amend the Greenhouse Gas Reporting Program (GHGRP), including technical amendments, amendments related to global warming potentials (GWPs), and confidentiality determinations for new or revised data elements.

Civilian Radioactive Waste Management System Requirements Document

DOE Office of Scientific and Technical Information (OSTI.GOV)

C.A. Kouts

2006-05-10

The CRD addresses the requirements of Department of Energy (DOE) Order 413.3-Change 1, ''Program and Project Management for the Acquisition of Capital Assets'', by providing the Secretarial Acquisition Executive (Level 0) scope baseline and the Program-level (Level 1) technical baseline. The Secretarial Acquisition Executive approves the Office of Civilian Radioactive Waste Management's (OCRWM) critical decisions and changes against the Level 0 baseline; and in turn, the OCRWM Director approves all changes against the Level 1 baseline. This baseline establishes the top-level technical scope of the CRMWS and its three system elements, as described in section 1.3.2. The organizations responsible formore » design, development, and operation of system elements described in this document must therefore prepare subordinate project-level documents that are consistent with the CRD. Changes to requirements will be managed in accordance with established change and configuration control procedures. The CRD establishes requirements for the design, development, and operation of the CRWMS. It specifically addresses the top-level governing laws and regulations (e.g., ''Nuclear Waste Policy Act'' (NWPA), 10 Code of Federal Regulations (CFR) Part 63, 10 CFR Part 71, etc.) along with specific policy, performance requirements, interface requirements, and system architecture. The CRD shall be used as a vehicle to incorporate specific changes in technical scope or performance requirements that may have significant program implications. Such may include changes to the program mission, changes to operational capability, and high visibility stakeholder issues. The CRD uses a systems approach to: (1) identify key functions that the CRWMS must perform, (2) allocate top-level requirements derived from statutory, regulatory, and programmatic sources, and (3) define the basic elements of the system architecture and operational concept. Project-level documents address CRD requirements by further defining system element functions, decomposing requirements into significantly greater detail, and developing designs of system components, facilities, and equipment. The CRD addresses the identification and control of functional, physical, and operational boundaries between and within CRWMS elements. The CRD establishes requirements regarding key interfaces between the CRWMS and elements external to the CRWMS. Project elements define interfaces between CRWMS program elements. The Program has developed a change management process consistent with DOE Order 413.3-Change 1. Changes to the Secretarial Acquisition Executive and Program-level baselines must be approved by a Program Baseline Change Control Board. Specific thresholds have been established for identifying technical, cost, and schedule changes that require approval. The CRWMS continually evaluates system design and operational concepts to optimize performance and/or cost. The Program has developed systems analysis tools to assess potential enhancements to the physical system and to determine the impacts from cost saving initiatives, scientific and technological improvements, and engineering developments. The results of systems analyses, if appropriate, are factored into revisions to the CRD as revised Programmatic Requirements.« less

Superexchange coupling and slow magnetic relaxation in a transuranium polymetallic complex.

PubMed

Magnani, N; Colineau, E; Eloirdi, R; Griveau, J-C; Caciuffo, R; Cornet, S M; May, I; Sharrad, C A; Collison, D; Winpenny, R E P

2010-05-14

{Np(VI)O2Cl2}{Np(V)O2Cl(thf)3}2 is the first studied example of a polymetallic transuranic complex displaying both slow relaxation of the magnetization and effective superexchange interactions between 5f centers. The coupling constant for Np(V)-Np(VI) pairs is 10.8 K, more than 1 order of magnitude larger than the common values found for rare-earth ions in similar environments. The dynamic magnetic behavior displays slow relaxation of magnetization of molecular origin with an energy barrier of 140 K, which is nearly twice the size of the highest barrier found in polymetallic clusters of the d block. Our observations also suggest that future actinide-based molecular magnets will have very different behavior to lanthanide-based clusters.

Development of NASA Technical Standards Program Relative to Enhancing Engineering Capabilities

NASA Technical Reports Server (NTRS)

Gill, Paul S.; Vaughan, William W.

2003-01-01

The enhancement of engineering capabilities is an important aspect of any organization; especially those engaged in aerospace development activities. Technical Standards are one of the key elements of this endeavor. The NASA Technical Standards Program was formed in 1997 in response to the NASA Administrator s directive to develop an Agencywide Technical Standards Program. The Program s principal objective involved the converting Center-unique technical standards into Agency wide standards and the adoption/endorsement of non-Government technical standards in lieu of government standards. In the process of these actions, the potential for further enhancement of the Agency s engineering capabilities was noted relative to value of being able to access Agencywide the necessary full-text technical standards, standards update notifications, and integration of lessons learned with technical standards, all available to the user from one Website. This was accomplished and is now being enhanced based on feedbacks from the Agency's engineering staff and supporting contractors. This paper addresses the development experiences with the NASA Technical Standards Program and the enhancement of the Agency's engineering capabilities provided by the Program s products. Metrics are provided on significant aspects of the Program.

Improvement of technical purpose materials performance characteristics with the radio frequency low pressure plasma

NASA Astrophysics Data System (ADS)

Makhotkina, L. Yu; Khristoliubova, V. I.

2017-11-01

The main aim of the work is to solve the actual problem of increasing the competitiveness of tanning products by reducing the prime cost and improving the quality of finished products due to the increased durability of the working elements of tanneries. The impact of the low pressure radio frequency (RF) plasma in the processes of treating for modification of the materials for special purposes is considered in the article. The results of working elements of tanneries and the materials for special purposes sample processing by a RF low pressure plasma are described. As a result of leather materials nano structuring and nano modifying physical, mechanical and hygienic characteristics were increased. Processing of the technical purpose materials allows to increase operational performance of products and extend their lifespan.

New Technical Solution for Vertical Shaft Equipping Using Steel Headframe of Multifunction Purpose

NASA Astrophysics Data System (ADS)

Kassikhina, Elena; Pershin, Vladimir; Glazkov, Yurij

2017-11-01

The article reviews a novel approach to the design of steel angle headframe for vertical shafts of coal and ore mines on the basis of rational design solutions. Practice of construction of coal and ore mines provides application of various designs for steel angle headframes which are divided into separate large assembly blocks and constructive elements during assembling operations. Design of these blocks and elements, their weight and dimensions effect the chose of the method of assembling on which economic and technological indicators, as well as duration of down-time, depend on during performance of construction operations in shaft. The technical solution on equipment provision for mine vertical shaft using headframe of multifunctional purpose will allow changing the management construction of vertical shaft. The constructive design of the headgear allows application of the effective method of assembly and thus to provide improvement of the technical and economic indexes, and high calendar time rate of the shaft construction due to reduction of duration of works on equipment provision for the shaft and to refurbishment of the shaft in order to carry out horizontal mining.

System configuration management plan for 101-SY Hydrogen Mitigation Test Project Mini-Data Acquisition and Control System of Tank Waste Remediation System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vargo, G.F. Jr.

1994-10-11

The DOE Standard defines the configuration management program by the five basic program elements of ``program management,`` ``design requirements,`` ``document control,`` ``change control,`` and ``assessments,`` and the two adjunct recovery programs of ``design reconstitution,`` and ``material condition and aging management. The C-M model of five elements and two adjunct programs strengthen the necessary technical and administrative control to establish and maintain a consistent technical relationship among the requirements, physical configuration, and documentation. Although the DOE Standard was originally developed for the operational phase of nuclear facilities, this plan has the flexibility to be adapted and applied to all life-cycle phasesmore » of both nuclear and non-nuclear facilities. The configuration management criteria presented in this plan endorses the DOE Standard and has been tailored specifically to address the technical relationship of requirements, physical configuration, and documentation during the full life-cycle of the 101-SY Hydrogen Mitigation Test Project Mini-Data Acquisition and Control System of Tank Waste Remediation System.« less

Cambio : a file format translation and analysis application for the nuclear response emergency community.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lasche, George P.

2009-10-01

Cambio is an application intended to automatically read and display any spectrum file of any format in the world that the nuclear emergency response community might encounter. Cambio also provides an analysis capability suitable for HPGe spectra when detector response and scattering environment are not well known. Why is Cambio needed: (1) Cambio solves the following problem - With over 50 types of formats from instruments used in the field and new format variations appearing frequently, it is impractical for every responder to have current versions of the manufacturer's software from every instrument used in the field; (2) Cambio convertsmore » field spectra to any one of several common formats that are used for analysis, saving valuable time in an emergency situation; (3) Cambio provides basic tools for comparing spectra, calibrating spectra, and isotope identification with analysis suited especially for HPGe spectra; and (4) Cambio has a batch processing capability to automatically translate a large number of archival spectral files of any format to one of several common formats, such as the IAEA SPE or the DHS N42. Currently over 540 analysts and members of the nuclear emergency response community worldwide are on the distribution list for updates to Cambio. Cambio users come from all levels of government, university, and commercial partners around the world that support efforts to counter terrorist nuclear activities. Cambio is Unclassified Unlimited Release (UUR) and distributed by internet downloads with email notifications whenever a new build of Cambio provides for new formats, bug fixes, or new or improved capabilities. Cambio is also provided as a DLL to the Karlsruhe Institute for Transuranium Elements so that Cambio's automatic file-reading capability can be included at the Nucleonica web site.« less

Organic and Aqueous Redox Speciation of Cu(III) Periodate Oxidized Transuranium Actinides

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCann, Kevin; Sinkov, Sergey I.; Lumetta, Gregg J.

A hexavalent group actinide separation process could streamline used nuclear fuel recycle and waste management. The limiting factor to such a process compatible with current fuel dissolution practices is obtaining and maintaining hexavalent Am, in molar nitric acid due to the high reduction potential of the Am(VI)/Am(III) couple (1.68 V vs SCE). Two strong oxidants, sodium bismuthate and Cu(III) periodate, have demonstrated quantitative oxidation of Am under molar acid conditions and better than 50% recovery by diamyl amylphosphonate (DAAP) is possible under these same conditions. This work considers the use of Cu(III) periodate to oxidize Np(V) to Np(VI) and Pu(IV)more » to Pu(VI) and recover these elements by extraction with DAAP. A metal:oxidant ratio of 1:1.2 and 1:3 was necessary to quantitatively oxidize Np(V) and Pu(IV), respectively, to the hexavalent state. Extraction of hexavalent Np, Pu, and Am by 1 M DAAP in n-dodecane was measured using UV-Vis [Pu(VI), Am (VI)] and NIR [Np(VI)]. Distribution values of Am(VI) were found to match previous tracer level studies. The organic phase spectra of Np, Pu, and Am are presented and molar absorptivities are calculated for characteristic peaks. Hexavalent Pu was found to be stable in the organic phase while Np(VI) showed some reduction to Np(V) and Am was present as Am(III), Am(V), and Am(VI) species in aqueous and organic phases during the extraction experiments. These results demonstrate, for the first time, the ability to recover macroscopic amounts of americium that would be present during fuel reprocessing and are the first characterization of Am organic phase oxidation state speciation relevant to a hexavalent group actinide separation process under acidic conditions.« less

Dissolution behavior of MgO based inert matrix fuel for the transmutation of minor actinides

NASA Astrophysics Data System (ADS)

Mühr-Ebert, E. L.; Lichte, E.; Bukaemskiy, A.; Finkeldei, S.; Klinkenberg, M.; Brandt, F.; Bosbach, D.; Modolo, G.

2018-07-01

This study explores the dissolution properties of magnesia-based inert matrix nuclear fuel (IMF) containing transuranium elements (TRU). Pure MgO pellets as well as MgO pellets containing CeO2, as surrogate for TRU oxides, and are considered as model systems for genuine magnesia based inert matrix fuel were fabricated. The aim of this study is to identify conditions at which the matrix material can be selectively dissolved during the head-end reprocessing step, allowing a separation of MgO from the actinides, whereas the actinides remain undissolved. The dissolution behavior was studied in macroscopic batch experiments as a function of nitric acid concentration, dissolution medium volume, temperature, stirring velocity, and pellet density (85, 90, 96, and 99%TD). To mimic pellets with various burn-ups the density of the here fabricated pellets was varied. MgO is soluble even under mild conditions (RT, 2.5 mol/L HNO3). The dissolution rates of MgO at different acid concentrations are rather similar, whereas the dissolution rate is strongly dependent on the temperature. Via a microscopic approach, a model was developed to describe the evolution of the pellet surface area during dissolution and determine a surface normalized dissolution rate. Moreover, dissolution rates of the inert matrix fuel containing CeO2 were determined as a function of the acid concentration and temperature. During the dissolution of MgO/CeO2 pellets the MgO dissolves completely, while CeO2 (>99%) remains undissolved. This study intends to provide a profound understanding of the chemical performance of magnesia based IMF containing fissile material. The feasibility of the dissolution of magnesia based IMF with nitric acid is discussed.

Dane Christensen | NREL

Science.gov Websites

-performance building simulation. Dane supports technical efforts for the Building America Program and conducts finite element modeling for building energy simulation. Prior to joining NREL, Dane worked at Atec, Inc

7 CFR 652.38 - Scope of decertification.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE Decertification § 652.38... auspices or to an organizational element of such private sector entity or public agency. The scope of...

04/02/2013 Fact Sheet

EPA Pesticide Factsheets

Fact sheet describing a proposal to amend the Greenhouse Gas Reporting Program (GHGRP), including technical amendments, amendments related to global warming potentials (GWPs), and confidentiality determinations for new or revised data elements.

The Classical Theory of Composition; From Its Origins to the Present: A Historical Survey (University of North Carolina Studies in Comparative Literature, No. 53.)

ERIC Educational Resources Information Center

Scaglione, Aldo

The major purpose of this study is the descriptive analysis of a large body of literature, mainly technical, which attempts to explain the structure of sentences and ordering of their elements, on the linguistic and artistic levels. It is hoped that this study helps to document the relevance of technical material for the proper understanding of…

ECUT: Energy Conversion and Utilization Technologies program. Biocatalysis project

NASA Technical Reports Server (NTRS)

1990-01-01

The Biocatalysis Project is a mission-oriented, applied research and exploratory development activity directed toward resolution of the major generic technical barriers that impede the development of biologically catalyzed commercial chemical production. The approach toward achieving project objectives involves an integrated participation of Universities, Industrial Companies and Government Research Laboratories. The Project's technical activities were organized into three work elements: molecular modeling and applied genetics; bioprocess engineering; and bioprocess design and assessment.

Evolution of Scientific and Technical Information Distribution

NASA Technical Reports Server (NTRS)

Esler, Sandra; Nelson, Michael L.

1998-01-01

World Wide Web (WWW) and related information technologies are transforming the distribution of scientific and technical information (STI). We examine 11 recent, functioning digital libraries focusing on the distribution of STI publications, including journal articles, conference papers, and technical reports. We introduce 4 main categories of digital library projects: based on the architecture (distributed vs. centralized) and the contributor (traditional publisher vs. authoring individual/organization). Many digital library prototypes merely automate existing publishing practices or focus solely on the digitization of the publishing cycle output, not sampling and capturing elements of the input. Still others do not consider for distribution the large body of "gray literature." We address these deficiencies in the current model of STI exchange by suggesting methods for expanding the scope and target of digital libraries by focusing on a greater source of technical publications and using "buckets," an object-oriented construct for grouping logically related information objects, to include holdings other than technical publications.

REQUIREMENT VERIFICATION AND SYSTEMS ENGINEERING TECHNICAL REVIEW (SETR) ON A COMMERCIAL DERIVATIVE AIRCRAFT (CDA) PROGRAM

DTIC Science & Technology

2017-09-01

the SETR entrance criteria of these events. Out of 30 evaluated SETR entrance criteria, 22 map to FAA elements. A case study of a military CDA...evaluated SETR entrance criteria, 22 map to FAA elements. A case study of a military CDA program, the Presidential Helicopter Replacement Program...3 C. SCOPE AND METHODOLOGY .................................................. 4 D. ORGANIZATION OF THESIS

Overview of NASA's Supersonic Cruise Efficiency - Propulsion Research

NASA Technical Reports Server (NTRS)

DeBonis, James R.

2009-01-01

The research in Supersonic Cruise Efficiency Propulsion (SCE-P) Technical Challenge area of NASA's Supersonics project is discussed. The research in SCE-P is being performed to enable efficient supersonic flight over land. Research elements in this area include: Advance Inlet Concepts, High Performance/Wider Operability Fan and Compressor, Advanced Nozzle Concepts, and Intelligent Sensors/Actuators. The research under each of these elements is briefly discussed.

Field Test Report of the Self-Directed, Interpretive, and Creative Reading Elements of the Wisconsin Design for Reading Skill Development. Technical Report No. 330.

ERIC Educational Resources Information Center

Chester, Robert; And Others

This study of the self-directed, interpretive, and creative reading elements of the Wisconsin Design for Reading Skill Development was conducted to gather descriptive data about implementation strategies being developed and practiced by field test teachers and to gather evaluative information about the usability of various management and…

The importance of defining technical issues in interagency environmental negotiations

USGS Publications Warehouse

Lamb, B.L.; Burkardt, N.; Taylor, J.G.

2001-01-01

The role of technical clarity in successful multiparty negotiations was studied. Investigations involved in-depth interviews with the principal participants in six consultations conducted under the U.S. Federal Energy Regulatory Commission’s hydroelectric power project licensing procedures. Technical clarity was especially important in these cases because they concerned science-based questions. The principal issues in the six cases were fish passage, instream flow for fish habitat, and entrainment of fish in hydropower turbines. It was concluded that technical clarity was one of the most critical elements in resolving these conflicts. In the least successful negotiations, parties failed to address the basic values of the dispute before plunging into technical studies. The results of those studies usually highlighted the potential for negative outcomes and increased polarization between the participants. In the most successful negotiations, the various parties shared an understanding of each of their basic values. These shared understandings led to technical studies that cast the negotiation in a positive light and illuminated possible solutions.

Synthetic biology and the technicity of biofuels.

PubMed

Mackenzie, Adrian

2013-06-01

The principal existing real-world application of synthetic biology is biofuels. Several 'next generation biofuel' companies-Synthetic Genomics, Amyris and Joule Unlimited Technologies-claim to be using synthetic biology to make biofuels. The irony of this is that highly advanced science and engineering serves the very mundane and familiar realm of transport. Despite their rather prosaic nature, biofuels could offer an interesting way to highlight the novelty of synthetic biology from several angles at once. Drawing on the French philosopher of technology and biology Gilbert Simondon, we can understand biofuels as technical objects whose genesis involves processes of concretisation that negotiate between heterogeneous geographical, biological, technical, scientific and commercial realities. Simondon's notion of technicity, the degree of concretisation of a technical object, usefully conceptualises this relationality. Viewed in terms of technicity, we might understand better how technical entities, elements, and ensembles are coming into being in the name of synthetic biology. The broader argument here is that when we seek to identify the newness of disciplines, their newness might be less epistemic and more logistic. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Rolling-Element Fatigue Testing and Data Analysis - A Tutorial

NASA Technical Reports Server (NTRS)

Vlcek, Brian L.; Zaretsky, Erwin V.

2011-01-01

In order to rank bearing materials, lubricants and other design variables using rolling-element bench type fatigue testing of bearing components and full-scale rolling-element bearing tests, the investigator needs to be cognizant of the variables that affect rolling-element fatigue life and be able to maintain and control them within an acceptable experimental tolerance. Once these variables are controlled, the number of tests and the test conditions must be specified to assure reasonable statistical certainty of the final results. There is a reasonable correlation between the results from elemental test rigs with those results obtained with full-scale bearings. Using the statistical methods of W. Weibull and L. Johnson, the minimum number of tests required can be determined. This paper brings together and discusses the technical aspects of rolling-element fatigue testing and data analysis as well as making recommendations to assure quality and reliable testing of rolling-element specimens and full-scale rolling-element bearings.

A study of space station needs, attributes and architectural options. Volume 2: Technical. Book 1: Mission requirements. Appendixes 1 and 2

NASA Technical Reports Server (NTRS)

1983-01-01

The space station mission requirements data base consists of 149 attached and free-flying missions each of which is documented by a set of three interrelated documents: (1) NASA LaRC Data Sheets - with three sheets comprising a set for each payload element described. These sheets contain user payload element data necessary to drive Space Station architectural options. (2) GDC-derived operations descriptions that supplement the LaRC payload element data in the operations areas such as further descriptions of crew involvement, EVA, etc. (3) Payload elements synthesis sheets used by GDC to provide requirements traceability to data sources and to provide a narrative describing the basis for formulating the payload element requirements.

Guidelines for the Selection of Chemical Protective Clothing. Volume 2. Technical and Reference Manual.

DTIC Science & Technology

1987-02-01

Handler’s Suit for Protection from Chlorine Trifluoride and Elemental Fluorine Technical Report AFRPL-TR-71-44 (August 1971) NTIS AD731556 199 Masterman’s...Protective Clothing for Chlorine , Edition 1 Chlorine Institute Pamphlet 65, The Chlorine Institute, Inc. New York, New York, (June 1978) 15 Anon...Chemical Company Selection of Gloves for Use With Chlorinated Solvents Chlorinated Solvents Information Midland, Michigan 48640 101 Duffy, R.M., A.R.Beer

[What did bachelard mean by "applied rationalism" ?].

PubMed

Tiles, Mary

2013-01-01

Bachelard was concerned with the processes whereby scientific knowledge is acquired, including the activity of knowing subjects. He did not equate reasoning with logic but rather argued that reasoning resulted from the use of mathematics in organizing both thought and experimental practices, which is why he conceived science as applied mathematics. This had material and technical implications, for Bachelard was concerned with the element of reason inherent in technical materialism as well as the concrete reality inherent in applied rationalism.

An improved finite element modeling of the cerebrospinal fluid layer in the head impact analysis.

PubMed

Wu, John Z; Pan, Christopher S; Wimer, Bryan M; Rosen, Charles L

2017-01-01

The finite element (FE) method has been widely used to investigate the mechanism of traumatic brain injuries (TBIs), because it is technically difficult to quantify the responses of the brain tissues to the impact in experiments. One of technical challenges to build a FE model of a human head is the modeling of the cerebrospinal fluid (CSF) of the brain. In the current study, we propose to use membrane elements to construct the CSF layer. Using the proposed approach, we demonstrate that a head model can be built by using existing meshes available in commercial databases, without using any advanced meshing software tool, and with the sole use of native functions of the FE package Abaqus. The calculated time histories of the intracranial pressures at frontal, posterior fossa, parietal, and occipital positions agree well with the experimental data and the simulations in the literature, indicating that the physical effects of the CSF layer have been accounted for in the proposed modeling approach. The proposed modeling approach would be useful for bioengineers to solve practical problems.

Development of decision- making mechanism in engineering design of phased coal mines technical upgrade

NASA Astrophysics Data System (ADS)

Kulak, V. Yu; Petrova, T. V.; Novichikhin, A. V.

2017-09-01

The approach to a choice of a new mine design and technical upgrade of operating coal mines is substantiated. The choice of the option is made in the following way: the elements of the mine technological system are defined, for each element of the system two levels of costs are allocated - capital and operational; a graph of alternative options of the system is formed by matrix enumeration taking into account the possibility of simultaneous application of different elements, up to 10 000 scenarios are formed; capital and operating costs of options are estimated in the form of coefficients as the cost-to-cost ratio in the base variant, which has already been implemented and the costs of which are already known; ranking of the options at the level of costs and the definition of the 10 preferred are performed. It is established that the application of partial enumeration allows the costs relative to the base variant to be reduced by 10 %; the main constraint of costs reduction is the need to comply with all conditions that ensure industrial safety.

Overview of the NASA Systems Approach to Crashworthiness Program

NASA Technical Reports Server (NTRS)

Jones, Lisa E.

2002-01-01

The NASA Aviation Safety Program was developed in response to the federal government's goal to reduce the fatal accident rate for aviation by 80% within 10 years. Accident Mitigation is a primary element of the Aviation Safety Program. The overall Accident Mitigation goal is to provide technology to the air transport industry to enable a decrease in the rate of fatalities and injury from crash loads and from in-flight and post-crash explosion and/or fire. Accident Mitigation is divided into two main elements - Fire Prevention and Systems Approach to Crashworthiness. The Systems Approach to Crashworthiness goal is to develop and promote technology that will increase the human survival rate or reduce the fatality rate in survivable accidents. The technical background and planning, selected technical activities, and summary of future efforts will be presented in this paper.

The manufacture of LEU fuel elements at Dounreay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gibson, J.

1997-08-01

Two LEU test elements are being manufactured at Dounreay for test irradiation in the HFR at Petten, The Netherlands. This paper describes the installation of equipment and the development of the fabrication and inspection techniques necessary for the manufacture of LEU fuel plates. The author`s experience in overcoming the technical problems of stray fuel particles, dog-boning, uranium homogeneity and the measurement of uranium distribution is also described.

Technical Report on the Behavior of Trace Elements, Stable Isotopes, and Radiogenic Isotopes During the Processing of Uranium Ore to Uranium Ore Concentrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marks, N. E.; Borg, L. E.; Eppich, G. R.

2015-07-09

The goals of this SP-1 effort were to understand how isotopic and elemental signatures behave during mining, milling, and concentration and to identify analytes that might preserve geologic signatures of the protolith ores. The impurities that are preserved through the concentration process could provide useful forensic signatures and perhaps prove diagnostic of sample origin.

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra aids in Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

NASA Image and Video Library

2004-02-03

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra aids in Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, workers check over the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

NASA Image and Video Library

2004-02-03

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, workers check over the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

A Synopsis of Technical Issues of Concern for Monitoring Trace Elements in Highway and Urban Runoff

USGS Publications Warehouse

Breault, Robert F.; Granato, Gregory E.

2000-01-01

Trace elements, which are regulated for aquatic life protection, are a primary concern in highway- and urban-runoff studies because stormwater runoff may transport these constituents from the land surface to receiving waters. Many of these trace elements are essential for biological activity and become detrimental only when geologic or anthropogenic sources exceed concentrations beyond ranges typical of the natural environment. The Federal Highway Administration and State Transportation Agencies are concerned about the potential effects of highway runoff on the watershed scale and for the management and protection of watersheds. Transportation agencies need information that is documented as valid, current, and scientifically defensible to support planning and management decisions. There are many technical issues of concern for monitoring trace elements; therefore, trace-element data commonly are considered suspect, and the responsibility to provide data-quality information to support the validity of reported results rests with the data-collection agency. Paved surfaces are fundamentally different physically, hydraulically, and chemically from the natural surfaces typical of most freshwater systems that have been the focus of many traceelement- monitoring studies. Existing scientific conceptions of the behavior of trace elements in the environment are based largely upon research on natural systems, rather than on systems typical of pavement runoff. Additionally, the logistics of stormwater sampling are difficult because of the great uncertainty in the occurrence and magnitude of storm events. Therefore, trace-element monitoring programs may be enhanced if monitoring and sampling programs are automated. Automation would standardize the process and provide a continuous record of the variations in flow and water-quality characteristics. Great care is required to collect and process samples in a manner that will minimize potential contamination or attenuation of trace elements and other sources of bias and variability in the sampling process. Trace elements have both natural and anthropogenic sources that may affect the sampling process, including the sample-collection and handling materials used in many trace-element monitoring studies. Trace elements also react with these materials within the timescales typical for collection, processing and analysis of runoff samples. To study the characteristics and potential effects of trace elements in highway and urban runoff, investigators typically sample one or more operationally defined matrixes including: whole water, dissolved (filtered water), suspended sediment, bottom sediment, biological tissue, and contaminant sources. The sampling and analysis of each of these sample matrixes can provide specific information about the occurrence and distribution of trace elements in runoff and receiving waters. There are, however, technical concerns specific to each matrix that must be understood and addressed through use of proper collection and processing protocols. Valid protocols are designed to minimize inherent problems and to maximize the accuracy, precision, comparability, and representativeness of data collected. Documentation, including information about monitoring protocols, quality assurance and quality control efforts, and ancillary data also is necessary to establish data quality. This documentation is especially important for evaluation of historical traceelement monitoring data, because trace-element monitoring protocols and analysis methods have been constantly changing over the past 30 years.

Louisiana CVO/ITS business plan : technical summary.

DOT National Transportation Integrated Search

1998-06-01

Louisiana seeks to improve the efficiency and effectiveness of CVO business and operational functions in the state. This overall mission includes three discrete elements designed to address priority needs as identified by state and industry stakehold...

Computer Security Systems Enable Access.

ERIC Educational Resources Information Center

Riggen, Gary

1989-01-01

A good security system enables access and protects information from damage or tampering, but the most important aspects of a security system aren't technical. A security procedures manual addresses the human element of computer security. (MLW)

Method for purifying bidentate organophosphorus compounds

DOEpatents

Schulz, Wallace W.

1977-01-01

Bidentate organophosphorus compounds useful for extracting actinide elements from acidic nuclear waste solutions are purified of undesirable acidic impurities by contacting the compounds with ethylene glycol which preferentially extracts the impurities found in technical grade bidentate compounds.

A Simplified Finite Element Simulation for Straightening Process of Thin-Walled Tube

NASA Astrophysics Data System (ADS)

Zhang, Ziqian; Yang, Huilin

2017-12-01

The finite element simulation is an effective way for the study of thin-walled tube in the two cross rolls straightening process. To determine the accurate radius of curvature of the roll profile more efficiently, a simplified finite element model based on the technical parameters of an actual two cross roll straightening machine, was developed to simulate the complex straightening process. Then a dynamic simulation was carried out using ANSYS LS-DYNA program. The result implied that the simplified finite element model was reasonable for simulate the two cross rolls straightening process, and can be obtained the radius of curvature of the roll profile with the tube’s straightness 2 mm/m.

Proceedings of a Conference on a Comprehensive Technical Review of Human Factors Technology in the Design-for-Maintainers Held at Pensacola Beach, Florida on 9-11 March 1982,

DTIC Science & Technology

1982-03-11

Lowery, 1969; Crawford & Altman, 1972; Rigney, Cremer , & Towne, 1965; Topmiller, 1964; see Hsu & Theisen, these Proceedings for a review) suggest...Factors Technical Memorandum No. 6021-1982-05). Warminster, PA: Naval Air Development Center, August 1982. Rigney, J. W., Cremer , R. H., & Towne, D. M. The...changes in the micro-elements. Several projects have employed time-synthesis simulation with generally positive results (Rigney, Cremer , Towne, & Mason

Probabilistic Structural Analysis Methods for select space propulsion system components (PSAM). Volume 3: Literature surveys and technical reports

NASA Technical Reports Server (NTRS)

1992-01-01

The technical effort and computer code developed during the first year are summarized. Several formulations for Probabilistic Finite Element Analysis (PFEA) are described with emphasis on the selected formulation. The strategies being implemented in the first-version computer code to perform linear, elastic PFEA is described. The results of a series of select Space Shuttle Main Engine (SSME) component surveys are presented. These results identify the critical components and provide the information necessary for probabilistic structural analysis.

P/M Processing of Rare Earth Modified High Strength Steels.

DTIC Science & Technology

1980-12-01

AA094 165 TRW INC CLEVELAND OH MATERIALS TECHNOLOGY F 6 P/N PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS DEC So A A SHEXM(ER NOOŕT76-C...LEVEL’ (7 PIM PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS By A. A. SHEINKER 00 TECHNICAL REPORT Prepared for Office of Naval Research...Processing of Rare Earth Modified High 1 Technical -’ 3t eC"Strength Steels * 1dc4,093Se~ 9PEFRIGOGNZTONAEADADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK

Toxic Hazards Research Unit Annual Technical Report: 1982

DTIC Science & Technology

1982-09-01

AFAMRL-TR-82-62 TOXIC HAZARDS RESEARCH UNIT ANNUAL TECHNICAL REPORT: 1962 J. D . MacERWI E. H. VRNOT UN! VERWflY OF CALIFORIA, IR V2VE P.O. BOX 3067...Government d .-auings, spec f&c-atons, o other data 2re used for an-, pirpose other than a definitely related Government procurement operation, the...GRANT NUMBER(s) J. D . MacEwen, E. H. Vernot F33615-80-C-0512 9 PERFORMING ORGANIZATION NAME: AND ADDRESS 10 PROGRAM ELEMENT. PROJECT. TASK University of

Configuration management plan for waste tank farms and the 242-A evaporator of tank waste remediation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laney, T.

The configuration management architecture presented in this Configuration Management Plan is based on the functional model established by DOE-STD-1073-93, ``Guide for Operational Configuration Management Program.`` The DOE Standard defines the configuration management program by the five basic program elements of ``program management,`` ``design requirements,`` ``document control,`` ``change control,`` and ``assessments,`` and the two adjunct recovery programs of ``design reconstitution,`` and ``material condition and aging management.`` The CM model of five elements and two adjunct programs strengthen the necessary technical and administrative control to establish and maintain a consistent technical relationship among the requirements, physical configuration, and documentation. Although the DOEmore » Standard was originally developed for the operational phase of nuclear facilities, this plan has the flexibility to be adapted and applied to all life-cycle phases of both nuclear and non-nuclear facilities. The configuration management criteria presented in this plan endorses the DOE Standard and has been tailored specifically to address the technical relationship of requirements, physical configuration, and documentation during the full life cycle of the Waste Tank Farms and 242-A Evaporator of Tank Waste Remediation System.« less

Assembling of Steel Angle Headframe of Multifunctional Purpose

NASA Astrophysics Data System (ADS)

Kassikhina, E. G.; Pershin, V. V.; Volkov, V. M.

2017-10-01

The article reviews new technical solution on equipment provision of vertical shaft utilizing steel headframe of multifunctional purpose. Practice of construction of coal and ore mines provides application of various designs for steel angle headframes which are divided into separate large assembly blocks and constructive elements during assembling operations. Design of these blocks and elements, their weight and dimensions effect the chose of the method of assembling on which economic and technological indicators, as well as duration of down-time, depend on during performance of construction operations in shaft. The technical solution on equipment provision for mine vertical shaft using headframe of multifunctional purpose will allow changing the management construction of vertical shaft. The proposed headframe combines the functions of sinking and operation that eliminates costs for assembling/dissembling of temporary headgear. The constructive design of the headgear allows application of the effective method of assembly and thus to provide improvement of the technical and economic indexes, and high calendar time rate of the shaft construction due to reduction of duration of works on equipment provision for the shaft and to refurbishment of the shaft in order to carry out horizontal mining.

Space station System Engineering and Integration (SE and I). Volume 2: Study results

NASA Technical Reports Server (NTRS)

1987-01-01

A summary of significant study results that are products of the Phase B conceptual design task are contained. Major elements are addressed. Study results applicable to each major element or area of design are summarized and included where appropriate. Areas addressed include: system engineering and integration; customer accommodations; test and program verification; product assurance; conceptual design; operations and planning; technical and management information system (TMIS); and advanced development.

Thermo-Physics Technical Note No. 60: thermal analysis of SNAP 10A reactor core during atmospheric reentry and resulting core disintegration and fuel element separation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mouradian, E.M.

1966-02-16

A thermal analysis is carried out to determine the temperature distribution throughout a SNAP 10A reactor core, particularly in the vicinity of the grid plates, during atmospheric reentry. The transient temperatue distribution of the grid plate indicates when sufficient melting occurs so that fuel elements are free to be released and continue their descent individually.

Efficient Computation Of Behavior Of Aircraft Tires

NASA Technical Reports Server (NTRS)

Tanner, John A.; Noor, Ahmed K.; Andersen, Carl M.

1989-01-01

NASA technical paper discusses challenging application of computational structural mechanics to numerical simulation of responses of aircraft tires during taxing, takeoff, and landing. Presents details of three main elements of computational strategy: use of special three-field, mixed-finite-element models; use of operator splitting; and application of technique reducing substantially number of degrees of freedom. Proposed computational strategy applied to two quasi-symmetric problems: linear analysis of anisotropic tires through use of two-dimensional-shell finite elements and nonlinear analysis of orthotropic tires subjected to unsymmetric loading. Three basic types of symmetry and combinations exhibited by response of tire identified.

The Care of Our Hybrid Selves: Ethics in Times of Technical Mediation.

PubMed

Dorrestijn, Steven

2017-01-01

What can the art of living after Foucault contribute to ethics in relation to the mediation of human existence by technology? To develop the relation between technical mediation and ethics, firstly the theme of technical mediation is elaborated in line with Foucault's notion of ethical problematization. Every view of what technology does to us at the same time expresses an ethical concern about technology. The contemporary conception of technical mediation tends towards the acknowledgement of ongoing hybridization, not ultimately good or bad but ambivalent, which means for us the challenge of taking care of ourselves as hybrid beings. Secondly, the work of Foucault provides elements for imagining this care for our hybrid selves, notably his notions of freedom as a practice and of the care of the self. A conclusions about technical mediation and ethics is that whereas the approaches of the delegation of morality to technology by Latour and mediated morality by Verbeek see technical mediation of behavior and moral outlook as an answer in ethics, this should rather be considered the problem that ethics is about.

Transposable elements in cancer.

PubMed

Burns, Kathleen H

2017-07-01

Transposable elements give rise to interspersed repeats, sequences that comprise most of our genomes. These mobile DNAs have been historically underappreciated - both because they have been presumed to be unimportant, and because their high copy number and variability pose unique technical challenges. Neither impediment now seems steadfast. Interest in the human mobilome has never been greater, and methods enabling its study are maturing at a fast pace. This Review describes the activity of transposable elements in human cancers, particularly long interspersed element-1 (LINE-1). LINE-1 sequences are self-propagating, protein-coding retrotransposons, and their activity results in somatically acquired insertions in cancer genomes. Altered expression of transposable elements and animation of genomic LINE-1 sequences appear to be hallmarks of cancer, and can be responsible for driving mutations in tumorigenesis.

Descriptive Chemistry in High School Curriculum.

ERIC Educational Resources Information Center

Rajan, Raj G.

1983-01-01

Discusses incorporation of descriptive chemistry and scientific/technical writing at the high school level. After discussing the periodic table, each student prepares a paper discussing the history, atomic data, occurring/extraction/purification, properties, and uses of an element. (JN)

Perspectives Of Employment Of Pultruded FRP Structural Elements In Seismic Engineering Field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russo, Salvatore; Silvestri, Mirko

2008-07-08

Today the employment of FRP material in structural engineering is in common use, with excellent results in term of applications especially as reinforcement of existing structures. This success is related to the very reduced weight of FRP material, to its performance in term of strength and durability and thanks to the easy use in technical application. There is a modern way to use this material disguised as structural pultruded element (with weight equal to 1600-1800 kg/m{sup 3}) in new constructions, local reinforcements and in other seismic applications. Actually the international technical and scientific literature in form of draft, recommendations andmore » researches on this topic is very rich also taking into account Italian contribution. Some interesting applications of all FRP structures in seismic engineering field are showed in this research in real terms and in form of capability.« less

Technical Reports: Langley Aerospace Research Summer Scholars. Part 1

NASA Technical Reports Server (NTRS)

Schwan, Rafaela (Compiler)

1995-01-01

The Langley Aerospace Research Summer Scholars (LARSS) Program was established by Dr. Samuel E. Massenberg in 1986. The program has increased from 20 participants in 1986 to 114 participants in 1995. The program is LaRC-unique and is administered by Hampton University. The program was established for the benefit of undergraduate juniors and seniors and first-year graduate students who are pursuing degrees in aeronautical engineering, mechanical engineering, electrical engineering, material science, computer science, atmospheric science, astrophysics, physics, and chemistry. Two primary elements of the LARSS Program are: (1) a research project to be completed by each participant under the supervision of a researcher who will assume the role of a mentor for the summer, and (2) technical lectures by prominent engineers and scientists. Additional elements of this program include tours of LARC wind tunnels, computational facilities, and laboratories. Library and computer facilities will be available for use by the participants.

Experimental and Numerical Analysis of Structural Acousticcontrol Interior Noise Reduction

NASA Technical Reports Server (NTRS)

Mei, Chuh; Bevan, Jeffrey S.

1999-01-01

The research results contained in this technical report were performed under the NASA grant entitled "Experimental and Numerical Structural Acoustic Control for Interior Noise Reduction". The report is based essentially on partial progress of the Ph.D. dissertation prepared by Jeffrey S. Bevan under direct guidance of Dr. Chuh Mei. The document presents a finite element formulation and control of sound radiated from cylindrical panels embedded with piezoceramic actuators. The extended MIN6 shallow shell element is fully electrical-structural coupled. A piezoelectric modal actuator participation (PMAP) is defined which indicates the actuator performance to each of the offending modes. Genetic algorithm is also employed to validate the sensor and actuator locations determined by the PMAP criteria. The work was conducted at the Department of Aerospace Engineering, Old Dominion University. Mr. Travis L. Turner, Structural Acoustics Branch, NASA Langley Research Center is the technical monitor.

The role of technical assistance in the replication of effective HIV interventions.

PubMed

O'Donnell, L; Scattergood, P; Adler, M; Doval, A S; Barker, M; Kelly, J A; Kegeles, S M; Rebchook, G M; Adams, J; Terry, M A; Neumann, M S

2000-01-01

This article examines the role of technical assistance (TA) in supporting the replication of proven HIV interventions. A case study of the replication of the VOICES/VOCES intervention elucidates the level and types of TA provided to support new users through the adoption process. TA included help in garnering administrative support, identifying target audiences, recruiting groups for sessions, maintaining fidelity to the intervention's core elements, tailoring the intervention to meet clients' needs, strengthening staff members' facilitation skills, troubleshooting challenges, and devising strategies to sustain the intervention. Two to four hours per month of TA were provided to each agency adopting the intervention, at an estimated monthly cost of $206 to $412. Findings illustrate how TA supports replication by establishing a conversation between the researcher TA providers experienced with the intervention and new users. This communication helps preserve key program elements and contributes to ongoing refinement of the intervention.

An Overview of the NASA FAP Hypersonics Project Airbreathing Propulsion Research

NASA Technical Reports Server (NTRS)

Auslender, A. H.; Suder, Kenneth L.; Thomas, Scott R.

2009-01-01

The propulsion research portfolio of the National Aeronautics and Space Administration Fundamental Aeronautics Program Hypersonics Project encompasses a significant number of technical tasks that are aligned to achieve mastery and intellectual stewardship of the core competencies in the hypersonic-flight regime. An overall coordinated programmatic and technical effort has been structured to advance the state-of-the-art, via both experimental and analytical efforts. A subset of the entire hypersonics propulsion research portfolio is presented in this overview paper. To this end, two programmatic research disciplines are discussed; namely, (1) the Propulsion Discipline, including three associated research elements: the X-51A partnership, the HIFiRE-2 partnership, and the Durable Combustor Rig, and (2) the Turbine-Based Combine Cycle Discipline, including three associated research elements: the Combined Cycle Engine Large Scale Inlet Mode Transition Experiment, the small-scale Inlet Mode Transition Experiment, and the High-Mach Fan Rig.

Isotope-abundance variations and atomic weights of selected elements: 2016 (IUPAC Technical Report)

USGS Publications Warehouse

Coplen, Tyler B.; Shrestha, Yesha

2016-01-01

There are 63 chemical elements that have two or more isotopes that are used to determine their standard atomic weights. The isotopic abundances and atomic weights of these elements can vary in normal materials due to physical and chemical fractionation processes (not due to radioactive decay). These variations are well known for 12 elements (hydrogen, lithium, boron, carbon, nitrogen, oxygen, magnesium, silicon, sulfur, chlorine, bromine, and thallium), and the standard atomic weight of each of these elements is given by IUPAC as an interval with lower and upper bounds. Graphical plots of selected materials and compounds of each of these elements have been published previously. Herein and at the URL http://dx.doi.org/10.5066/F7GF0RN2, we provide isotopic abundances, isotope-delta values, and atomic weights for each of the upper and lower bounds of these materials and compounds.

Space platform expendables resupply concept definition study. Volume 3: Work breakdown structure and work breakdown structure dictionary

NASA Technical Reports Server (NTRS)

1984-01-01

The work breakdown structure (WBS) for the Space Platform Expendables Resupply Concept Definition Study is described. The WBS consists of a list of WBS elements, a dictionary of element definitions, and an element logic diagram. The list and logic diagram identify the interrelationships of the elements. The dictionary defines the types of work that may be represented by or be classified under each specific element. The Space Platform Expendable Resupply WBS was selected mainly to support the program planning, scheduling, and costing performed in the programmatics task (task 3). The WBS is neither a statement-of-work nor a work authorization document. Rather, it is a framework around which to define requirements, plan effort, assign responsibilities, allocate and control resources, and report progress, expenditures, technical performance, and schedule performance. The WBS element definitions are independent of make-or-buy decisions, organizational structure, and activity locations unless exceptions are specifically stated.

Impact of IQ, computer-gaming skills, general dexterity, and laparoscopic experience on performance with the da Vinci surgical system.

PubMed

Hagen, Monika E; Wagner, Oliver J; Inan, Ihsan; Morel, Philippe

2009-09-01

Due to improved ergonomics and dexterity, robotic surgery is promoted as being easily performed by surgeons with no special skills necessary. We tested this hypothesis by measuring IQ elements, computer gaming skills, general dexterity with chopsticks, and evaluating laparoscopic experience in correlation to performance ability with the da Vinci robot. Thirty-four individuals were tested for robotic dexterity, IQ elements, computer-gaming skills and general dexterity. Eighteen surgically inexperienced and 16 laparoscopically trained surgeons were included. Each individual performed three different tasks with the da Vinci surgical system and their times were recorded. An IQ test (elements: logical thinking, 3D imagination and technical understanding) was completed by each participant. Computer skills were tested with a simple computer game (hand-eye coordination) and general dexterity was evaluated by the ability to use chopsticks. We found no correlation between logical thinking, 3D imagination and robotic skills. Both computer gaming and general dexterity showed a slight but non-significant improvement in performance with the da Vinci robot (p > 0.05). A significant correlation between robotic skills, technical understanding and laparoscopic experience was observed (p < 0.05). The data support the conclusion that there are no significant correlations between robotic performance and logical thinking, 3D understanding, computer gaming skills and general dexterity. A correlation between robotic skills and technical understanding may exist. Laparoscopic experience seems to be the strongest predictor of performance with the da Vinci surgical system. Generally, it appears difficult to determine non-surgical predictors for robotic surgery.

Comparison of a traditional with a new approach based on Graph Theory to vulnerability assessment to natural hazards: a study case on a socio-economic complex system

NASA Astrophysics Data System (ADS)

Arosio, Marcello; Martina, Mario L. V.

2017-04-01

The emergent behaviour of the contemporary complex, socio-technical and interconnected society makes the collective risk greater than the sum of the parts and this requires a holistic, systematic and integrated approach. Although there have been major improvements in recent years, there are still some limitation in term of a holistic approach that is able to include the emergent value hidden in the connections between exposed elements and the interactions between the different spheres of the multi-hazards, vulnerability, exposure and resilience. To deal with these challenges it is necessary to consider the connections between the exposed elements (e.g. populations, schools, hospital, etc.) and to quantify the relative importance of the elements and their interconnections (e.g. the need of injured people to go to hospital or children to school). In a system (e.g. road, hospital and ecological network, etc.), or in a System of System (e.g. socio-technical urban service), there are critical elements that, beyond the intrinsic vulnerability, can be characterized by greater or lower vulnerability because of their physical, geographical, cyber or logical connections. To this aim, we propose in this study a comparative analysis between traditional reductionist approach and a new holistic approach to vulnerability assessment to natural hazards. The analysis considers a study case of a socio-economic complex system through an innovative approach based on the properties of graph G=(N,L). A graph consists of two sets N (nodes) and L (links): the nodes represent the single exposed elements (physical, social, environmental, etc.) to a hazard, while the links (or connections) represent the interaction between the elements. The final goal is to illustrate an application of this innovative approach of integrated collective vulnerability assessment.

Lessons Learned and Technical Standards: A Logical Marriage for Future Space Systems Design

NASA Technical Reports Server (NTRS)

Gill, Paul S.; Garcia, Danny; Vaughan, William W.; Parker, Nelson C. (Technical Monitor)

2002-01-01

A comprehensive database of engineering lessons learned that corresponds with relevant technical standards will be a valuable asset to those engaged in studies on future space vehicle developments, especially for structures, materials, propulsion, control, operations and associated elements. In addition, this will enable the capturing of technology developments applicable to the design, development, and operation of future space vehicles as planned in the Space Launch Initiative. Using the time-honored tradition of passing on lessons learned while utilizing the newest information technology, NASA has launched an intensive effort to link lessons learned acquired through various Internet databases with applicable technical standards. This paper will discuss the importance of lessons learned, the difficulty in finding relevant lessons learned while engaged in a space vehicle development, and the new NASA effort to relate them to technical standards that can help alleviate this difficulty.

A Recommendation for the Heavy Division Command Group

DTIC Science & Technology

1994-06-03

Numbers. To include contract from the Standard Distribution for and grant numbers; may include program Unclassified Scientific and Technical element...blank. C - Contract PR - Project G - Grant TA -Task PE - Program WU - Work Unit Block 13. Abstract, Include a brief (Maximum Element Accession No. 200...Ronald E. McConnell, M.B.A., M.A. Accepted this 3rd day of June 1994 by. A •" Director, Graduate Degree Philip Brooes, Ph.D. Program The opinions and

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra (facing camera) aids in Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

NASA Image and Video Library

2004-02-03

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra (facing camera) aids in Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra talks to a technician (off-camera) during Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

NASA Image and Video Library

2004-02-03

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra talks to a technician (off-camera) during Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

Controlled Waveform Magnets

NASA Astrophysics Data System (ADS)

Campbell, L. J.; Schlllig, J. B.

Issues for the design and operation of high field controlled waveform magnets and their power supplies are discussed. The basic technical elements are reviewed and applied to problems specific to this class of magnets. Examples are given along with a guide to the literature.

48 CFR 9.104-1 - General standards.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Section 9.104-1 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION ACQUISITION PLANNING... them (including, as appropriate, such elements as production control procedures, property control... necessary production, construction, and technical equipment and facilities, or the ability to obtain them...

48 CFR 9.104-1 - General standards.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Section 9.104-1 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION ACQUISITION PLANNING... them (including, as appropriate, such elements as production control procedures, property control... necessary production, construction, and technical equipment and facilities, or the ability to obtain them...

48 CFR 9.104-1 - General standards.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Section 9.104-1 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION ACQUISITION PLANNING... them (including, as appropriate, such elements as production control procedures, property control... necessary production, construction, and technical equipment and facilities, or the ability to obtain them...

Use of graphics and symbols on dynamic message signs : technical report.

DOT National Transportation Integrated Search

2009-03-01

This project has taken a step toward defining how graphic and symbol displays can improve or assist communication with drivers. Through three human factors evaluations of alternative designs, researchers identified specific design elements that shoul...

Developing design elements for scenic byways in Virginia : final report.

DOT National Transportation Integrated Search

1991-01-01

Virginia has had a scenic roads program since 1966 that provides for the designation of certain roads as Virginia Byways. This program does not require the application of any special technical requirements in the selection, designation, maintenance, ...

Parallel Algorithms for Groebner-Basis Reduction

DTIC Science & Technology

1987-09-25

22209 ELEMENT NO. NO. NO. ACCESSION NO. 11. TITLE (Include Security Classification) * PARALLEL ALGORITHMS FOR GROEBNER -BASIS REDUCTION 12. PERSONAL...All other editions are obsolete. Productivity Engineering in the UNIXt Environment p Parallel Algorithms for Groebner -Basis Reduction Technical Report

THE RARE EARTH ELEMENTS THULIUM AND PROMETHIUM BECOME TECHNICALLY VALUABLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kogan, B.I.

1957-01-01

A survey of non-Slavic (mainly American) literature on thulium and promethium is given. Their preparation, propenties, and uses are considered. Thulium is used in flow detection, and promethium is used in miniature batteries. 20 references. (TCO)

Designing Clinical Remediation Programs.

ERIC Educational Resources Information Center

Oleszewski, Susan C.

1989-01-01

Elements and considerations in the provision of effective remediation for optometry students not achieving in clinical competence are discussed. Remediation of technical, cognitive, and noncognitive skills are included. A course in professional communication offered by the Pennsylvania College of Optometry is described. (MSE)

U.S. DOE’s Energy Treasure Hunt Exchange In-Plant Trainings – DOE Resources, Early Results and Lessons Learned

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nimbalkar, Sachin U.; Brockway, Walter F.; Lung, Bruce

The primary objective of the Department of Energy’s (DOE) Energy Treasure Hunt In-Plant Training (INPLT) is to train Better Plants partner employees to lead and conduct future energy efficiency Treasure Hunts within their facilities without DOE assistance. By taking a “learning-by-doing” approach, this INPLT, like other DOE INPLT trainings, has the added benefit of uncovering real energy and cost-saving opportunities. This INPLT leverages DOE and Better Plants technical staff, resources and tools and the EPA “Energy Treasure Hunt Guide: Simple Steps to Finding Energy Savings” process. While Treasure Hunts are a relatively well-known approach to identifying energy-savings in manufacturing plants,more » DOE is adding several additional elements in its Treasure Hunt Exchanges. The first element is technical assistance and methodology. DOE provides high-quality technical resources, such as energy efficiency calculators, fact sheets, source books etc., to facilitate the Treasure Hunt process and teaches four fundamentals: 1) how to profile equipment, 2) how to collect data, and 3), data & ROI calculation methodologies. Another element is the “train the trainer” approach wherein the training facilitator will train at least one partner employee to facilitate future treasure hunts. Another element is that DOE provides energy diagnostic equipment and teaches the participants how to use them. Finally, DOE also offers partners the opportunity to exchange teams of employees either within a partners’ enterprise or with other partners to conduct the treasure hunt in each other’s facilities. This exchange of teams is important because each team can bring different insights and uncover energy-saving opportunities that would otherwise be missed. This paper will discuss DOE methodology and the early results and lessons learned from DOE’S Energy Treasure Hunt In-Plant Trainings at Better Plants Partner facilities.« less

Use of energy filtering transmission electron microscopy for image generation and element analysis in plant organisms.

PubMed

Lütz-Meindl, Ursula

2007-01-01

Energy filtering TEM (EFTEM) with modern spectrometers and software offers new possibilities for element analysis and image generation in plant cells. In the present review, applications of EFTEM in plant physiology, such as identification of light elements and ion transport, analyses of natural cell incrustations, determination of element exchange between fungi and rootlets during mycorrhiza development, heavy metal storage and detoxification, and employment in plant physiological experiments are summarized. In addition, it is demonstrated that EFTEM can be successfully used in more practical approaches, for example, in phytoremediation, food and wood industry, and agriculture. Preparation methods for plant material as prerequisites for EFTEM analysis are compared with respect to their suitability and technical problems are discussed.

Geology and assessment of the undiscovered, technically recoverable petroleum resources of Armenia, 2013

USGS Publications Warehouse

Klett, T.R.

2016-02-23

The U.S. Geological Survey (USGS) assessed the undiscovered, technically recoverable oil and gas resources of Armenia in 2013. A Paleozoic and a Cenozoic total petroleum system (TPS) were identified within the country of Armenia. The postulated petroleum system elements are uncertain, resulting in low geologic probabilities for significant oil an gas resources. Two assessment units (AU) were delineated in each TPS—a Paleozoic-Sourced Conventional Reservoirs AU and a Permian Shale Gas AU in the Paleozoic Composite TPS and a Paleogene-Sourced Conventional Reservoirs AU and a Cenozoic Coalbed Gas AU in the Cenozoic Composite TPS. The TPS elements are largely uncertain and risked, and so only the Paleogene-Sourced Conventional Reservoirs AU was quantitatively assessed because the geologic probability is more than the threshold of 10 percent (that is, the probability of at least one conventional oil or gas accumulation of 5 million barrels of oil equivalent or greater based on postulated petroleum-system elements). The USGS estimated fully risked mean volumes of about 1 million barrels of oil (MMBO), about 6 billion cubic feet of natural gas (BCFG), and less than 1 million barrels of natural gas liquids (MMBNGL).

Supersonics--Airport Noise

NASA Technical Reports Server (NTRS)

Bridges, James

2007-01-01

At this, the first year-end meeting of the Fundamental Aeronautics Program, an overview of the Airport Noise discipline of the Supersonics Project leads the presentation of technical plans and achievements in this area of the Project. The overview starts by defining the Technical Challenges targeted by Airport Noise efforts, and the Approaches planned to meet these challenges. These are fleshed out in Elements, namely Prediction, Diagnostics, and Engineering, and broken down into Tasks. The Tasks level is where individual researchers' work is defined and from whence the technical presentations to follow this presentation come. This overview also presents the Milestones accomplished to date and to be completed in the next year. Finally, the NASA Research Announcement cooperative agreement activities are covered and tied to the Tasks and Milestones.

Solar Systems

NASA Technical Reports Server (NTRS)

1979-01-01

The solar collectors shown are elements of domestic solar hot water systems produced by Solar One Ltd., Virginia Beach, Virginia. Design of these systems benefited from technical expertise provided Solar One by NASA's Langley Research Center. The company obtained a NASA technical support package describing the d e sign and operation of solar heating equipment in NASA's Tech House, a demonstration project in which aerospace and commercial building technology are combined in an energy- efficient home. Solar One received further assistance through personal contact with Langley solar experts. The company reports that the technical information provided by NASA influenced Solar One's panel design, its selection of a long-life panel coating which increases solar collection efficiency, and the method adopted for protecting solar collectors from freezing conditions.

Space station related investigations in Europe

NASA Astrophysics Data System (ADS)

Wienss, W.; Vallerain, E.

1984-10-01

Studies pertaining to the definition of Europe's role in the Space Station program are described, with consideration given to such elements as pressurized modules as laboratories for materials processing and life sciences, unpressurized elements, and service vehicles for on-orbit maintenance and repair activities. Candidate elements were selected against such criteria as clean interfaces, the satisfaction of European user needs, new technology items, and European financial capabilities; and their technical and programmatic implications were examined. Different scenarios were considered, ranging from a fully Space-Station-dependent case to a completely autonomous, free-flying man-tendable configuration. Recommendations on a collaboration between Europe and the United States are presented.

High-Performance, Radiation-Hardened Electronics for Space and Lunar Environments

NASA Technical Reports Server (NTRS)

Keys, Andrew S.; Adams, James H.; Cressler, John D.; Darty, Ronald C.; Johnson, Michael A.; Patrick, Marshall C.

2008-01-01

The Radiation Hardened Electronics for Space Environments (RHESE) project develops advanced technologies needed for high performance electronic devices that will be capable of operating within the demanding radiation and thermal extremes of the space, lunar, and Martian environment. The technologies developed under this project enhance and enable avionics within multiple mission elements of NASA's Vision for Space Exploration. including the Constellation program's Orion Crew Exploration Vehicle. the Lunar Lander project, Lunar Outpost elements, and Extra Vehicular Activity (EVA) elements. This paper provides an overview of the RHESE project and its multiple task tasks, their technical approaches, and their targeted benefits as applied to NASA missions.

Multi-element germanium detectors for synchrotron applications

NASA Astrophysics Data System (ADS)

Rumaiz, A. K.; Kuczewski, A. J.; Mead, J.; Vernon, E.; Pinelli, D.; Dooryhee, E.; Ghose, S.; Caswell, T.; Siddons, D. P.; Miceli, A.; Baldwin, J.; Almer, J.; Okasinski, J.; Quaranta, O.; Woods, R.; Krings, T.; Stock, S.

2018-04-01

We have developed a series of monolithic multi-element germanium detectors, based on sensor arrays produced by the Forschungzentrum Julich, and on Application-specific integrated circuits (ASICs) developed at Brookhaven. Devices have been made with element counts ranging from 64 to 384. These detectors are being used at NSLS-II and APS for a range of diffraction experiments, both monochromatic and energy-dispersive. Compact and powerful readout systems have been developed, based on the new generation of FPGA system-on-chip devices, which provide closely coupled multi-core processors embedded in large gate arrays. We will discuss the technical details of the systems, and present some of the results from them.

NASA's 2004 Hall Thruster Program

NASA Technical Reports Server (NTRS)

Jacobson, David T.; Manzella, David H.; Hofer, Richard R.; Peterson, Peter Y.

2004-01-01

An overview of NASA's Hall thruster research and development tasks conducted during fiscal year 2004 is presented. These tasks focus on: raising the technology readiness level of high power Hall thrusters, developing a moderate-power/ moderate specific impulse Hall thruster, demonstrating high-power/high specific impulse Hall thruster operation, and addressing the fundamental technical challenges of emerging Hall thruster concepts. Programmatic background information, technical accomplishments and out year plans for each program element performed under the sponsorship of the In-Space Transportation Program, Project Prometheus, and the Energetics Project are provided.

Experiment Definition Using the Space Laboratory, Long Duration Exposure Facility, and Space Transportation System Shuttle

NASA Technical Reports Server (NTRS)

Sheppard, Albert P.; Wood, Joan M.

1976-01-01

Candidate experiments designed for the space shuttle transportation system and the long duration exposure facility are summarized. The data format covers: experiment title, Experimenter, technical abstract, benefits/justification, technical discussion of experiment approach and objectives, related work and experience, experiment facts space properties used, environmental constraints, shielding requirements, if any, physical description, and sketch of major elements. Information was also included on experiment hardware, research required to develop experiment, special requirements, cost estimate, safety considerations, and interactions with spacecraft and other experiments.

Observation of cosmic-ray particles with Z of 50 or greater and interpretation of the charge spectrum.

NASA Technical Reports Server (NTRS)

Blanford, G. E., Jr.; Friedlander, M. W.; Klarmann, J.; Walker, R. M.; Wefel, J. P.

1973-01-01

Large areas of plastic detectors and nuclear emulsions were exposed to the primary cosmic radiation on two high-altitude balloon flights in May 1968 and September 1969. From measurements on the tracks found in the scanning of the plastic detectors, events with charges Z greater than 50 were selected, and these data were consolidated with those from our earlier flights. Several conclusions can be drawn from the observed charge spectrum. The detection of trans-bismuth nuclei confirms earlier observations of these particles in the cosmic rays. However, no trans-uranium particles were observed. Detailed features of the charge spectrum cannot be explained by nuclei from r-process nucleosynthesis alone. Although the addition of particles following s-process abundances yields improved agreement, the spectrum appears more complicated than would result from a simple combination of r- and s-process abundances with identical propagation histories.

Preparation and X-Ray diffraction studies of curium hydrides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gibson, J.K.; Maire, R.G.

Curium hydrides were prepared by reaction of curium-248 metal with hydrogen and characterized by X-ray powder diffraction. Several of the syntheses resulted in a hexagonal compound with average lattice parameters of a/sub 0/ = 0.3769(8) nm and c/sub 0/ = 0.6732(12) nm. These products are considere to be CmH/sub 3//sup -//sub 8/ by analogy with the behavior of lanthanide-hydrogen and lighter actinide-hydrogen systems. Face-centered cubic products with an average lattice parameter of a/sub 0/ = 0.5322(4) nm were obtained from other curium hydride preparations. This parameter is slightly smaller than that reported previously for cubic curium dihydride, CmH /SUB 2-x/more » (B.M. Bansal and D. Damien. Inorg. Nucl. Chem. Lett. 6 603, 1970). The present results established a continuation of typical heavy trivalent lanthanidelike behavior of the transuranium actinide-hydrogen systems through curium.« less

Preparation and X-ray diffraction studies of curium hydrides

NASA Astrophysics Data System (ADS)

Gibson, J. K.; Haire, R. G.

1985-10-01

Curium hydrides were prepared by reaction of curium-248 metal with hydrogen and characterized by X-ray powder diffraction. Several of the syntheses resulted in a hexagonal compound with average lattice parameters of a0 = 0.3769(8) nm and c0 = 0.6732(12) nm. These products are considered to be CmH 3-δ by analogy with the behavior of lanthanide-hydrogen and lighter actinide-hydrogen systems. Face-centered cubic products with an average lattice parameter of a0 = 0.5322(4) nm were obtained from other curium hydride preparations. This parameter is slightly smaller than that reported previously for cubic curium dihydride, CmH 2+ x (B. M. Bansal and D. Damien, Inorg. Nucl. Chem. Lett., 6, 603, 1970). The present results established a continuation of typical heavy trivalent lanthanide-like behavior of the transuranium actinide-hydrogen systems through curium.

Comprehensive Transit Plan for the Virgin Islands - Technical Report

DOT National Transportation Integrated Search

1989-01-01

This report contains a description of the elements and recommendations of a transportation study of the islands of St. Thomas, St. Croix, and St. John in the U.S. Virgin Island archipelago. An extensive data collection effort, including traffic volum...

The Human Element of Project Management

ERIC Educational Resources Information Center

Gillard, Sharlett

2017-01-01

Much research and dialogue have been published about project management. Studies have been conducted regarding the impact of size, member location, gender composition, cross-functional structure, stakeholder influence, confidence issues, technology usage, management style, generational differences, technical expertise vs. people skills, and a…

Fourteenth NASTRAN (R) Users' Colloquium

NASA Technical Reports Server (NTRS)

1986-01-01

The proceedings of a colloquium are presented along with technical papers contributed during the conference. Reviewed are general applications of finite element methodology and the specific application of the NASA Structural Analysis System, NASTRAN, to a variety of static and dynamic sturctural problems.

United States Air Force Graduate Student Summer Support Program (1987). Program Technical Report. Volume 1.

DTIC Science & Technology

1987-12-01

developed for a large percentage of the participants in the Summer Faculty Research Program in 1979-1983 period through an AFOSR Minigrant Program . On 1...Analysis of a Bimodal Nuclear Rocket Core by Dav,, C. Carpenter ABSTRACT The framework for a general purpose finite element analysis code was developed ...to study the 2-D temperature distribution in a hot-channel S hexagonal fuel element in the core of a bimodal nuclear’ rocket. Prelim- inary thermal

The tracking, calorimeter and muon detectors of the H1 experiment at HERA

NASA Astrophysics Data System (ADS)

Abt, I.; Ahmed, T.; Aid, S.; Andreev, V.; Andrieu, B.; Appuhn, R.-D.; Arnault, C.; Arpagaus, M.; Babaev, A.; Bärwolff, H.; Bán, J.; Banas, E.; Baranov, P.; Barrelet, E.; Bartel, W.; Barth, M.; Bassler, U.; Basti, F.; Baynham, D. E.; Baze, J.-M.; Beck, G. A.; Beck, H. P.; Bederede, D.; Behrend, H.-J.; Beigbeder, C.; Belousov, A.; Berger, Ch.; Bergstein, H.; Bernard, R.; Bernardi, G.; Bernet, R.; Bernier, R.; Berthon, U.; Bertrand-Coremans, G.; Besançon, M.; Beyer, R.; Biasci, J.-C.; Biddulph, P.; Bidoli, V.; Binder, E.; Binko, P.; Bizot, J.-C.; Blobel, V.; Blouzon, F.; Blume, H.; Borras, K.; Boudry, V.; Bourdarios, C.; Brasse, F.; Braunschweig, W.; Breton, D.; Brettel, H.; Brisson, V.; Bruncko, D.; Brune, C.; Buchner, U.; Büngener, L.; Bürger, J.; Büsser, F. W.; Buniatian, A.; Burke, S.; Burmeister, P.; Busata, A.; Buschhorn, G.; Campbell, A. J.; Carli, T.; Charles, F.; Charlet, M.; Chase, R.; Clarke, D.; Clegg, A. B.; Colombo, M.; Commichau, V.; Connolly, J. F.; Cornett, U.; Coughlan, J. A.; Courau, A.; Cousinou, M.-C.; Coutures, Ch.; Coville, A.; Cozzika, G.; Cragg, D. A.; Criegee, L.; Cronström, H. I.; Cunliffe, N. H.; Cvach, J.; Cyz, A.; Dagoret, S.; Dainton, J. B.; Danilov, M.; Dann, A. W. E.; Darvill, D.; Dau, W. D.; David, J.; David, M.; Day, R. J.; Deffur, E.; Delcourt, B.; Del Buono, L.; Descamps, F.; Devel, M.; Dewulf, J. P.; De Roeck, A.; Dingus, P.; Djiki, K.; Dollfus, C.; Dowell, J. D.; Dreis, H. B.; Drescher, A.; Dretzler, U.; Duboc, J.; Ducorps, A.; Düllmann, D.; Dünger, O.; Duhm, H.; Dulny, B.; Dupont, F.; Ebbinghaus, R.; Eberle, M.; Ebert, J.; Ebert, T. R.; Eckerlin, G.; Edwards, B. W. H.; Efremenko, V.; Egli, S.; Eichenberger, S.; Eichler, R.; Eisele, F.; Eisenhandler, E.; Ellis, N. N.; Ellison, R. J.; Elsen, E.; Epifantsev, A.; Erdmann, M.; Erdmann, W.; Ernst, G.; Evrard, E.; Falley, G.; Favart, L.; Fedotov, A.; Feeken, D.; Felst, R.; Feltesse, J.; Feng, Z. Y.; Fensome, I. F.; Fent, J.; Ferencei, J.; Ferrarotto, F.; Finke, K.; Flamm, K.; Flauger, W.; Fleischer, M.; Flieser, M.; Flower, P. S.; Flügge, G.; Fomenko, A.; Fominykh, B.; Forbush, M.; Formánek, J.; Foster, J. M.; Franke, G.; Fretwurst, E.; Fröchtenicht, W.; Fuhrmann, P.; Gabathuler, E.; Gabathuler, K.; Gadow, K.; Gamerdinger, K.; Garvey, J.; Gayler, J.; Gažo, E.; Gellrich, A.; Gennis, M.; Gensch, U.; Genzel, H.; Gerhards, R.; Geske, K.; Giesgen, I.; Gillespie, D.; Glasgow, W.; Godfrey, L.; Godlewski, J.; Goerlach, U.; Goerlich, L.; Gogitidze, N.; Goldberg, M.; Goodall, A. M.; Gorelov, I.; Goritchev, P.; Gosset, L.; Grab, C.; Grässler, H.; Grässler, R.; Greenshaw, T.; Gregory, C.; Greif, H.; Grewe, M.; Grindhammer, G.; Gruber, A.; Gruber, C.; Günther, S.; Haack, J.; Haguenauer, M.; Haidt, D.; Hajduk, L.; Hammer, D.; Hamon, O.; Hampel, M.; Handschuh, D.; Hangarter, K.; Hanlon, E. M.; Hapke, M.; Harder, U.; Harjes, J.; Hartz, P.; Hatton, P. E.; Haydar, R.; Haynes, W. J.; Heatherington, J.; Hedberg, V.; Hedgecock, C. R.; Heinzelmann, G.; Henderson, R. C. W.; Henschel, H.; Herma, R.; Herynek, I.; Hildesheim, W.; Hill, P.; Hill, D. L.; Hilton, C. D.; Hladký, J.; Hoeger, K. C.; Hopes, R. B.; Horisberger, R.; Hrisoho, A.; Huber, J.; Huet, Ph.; Hufnagel, H.; Huot, N.; Huppert, J.-F.; Ibbotson, M.; Imbault, D.; Itterbeck, H.; Jabiol, M.-A.; Jacholkowska, A.; Jacobsson, C.; Jaffré, M.; Janoth, J.; Jansen, T.; Jean, P.; Jeanjean, J.; Jönsson, L.; Johannsen, K.; Johnson, D. P.; Johnson, L.; Jovanovic, P.; Jung, H.; Kalmus, P. I. P.; Kant, D.; Kant, D.; Kantel, G.; Karstensen, S.; Kasarian, S.; Kaschowitz, R.; Kasselmann, P.; Kathage, U.; Kaufmann, H. H.; Kemmerling, G.; Kenyon, I. R.; Kermiche, S.; Keuker, C.; Kiesling, C.; Klein, M.; Kleinwort, C.; Knies, G.; Ko, W.; Kobler, T.; Koch, J.; Köhler, T.; Köhne, J.; Kolander, M.; Kolanoski, H.; Kole, F.; Koll, J.; Kolya, S. D.; Koppitz, B.; Korbel, V.; Korn, M.; Kostka, P.; Kotelnikov, S. K.; Krasny, M. W.; Krehbiel, H.; Krivan, F.; Krücker, D.; Krüger, U.; Krüner-Marquis, U.; Kubantsev, M.; Kubenka, J. P.; Külper, T.; Küsel, H.-J.; Küster, H.; Kuhlen, M.; Kurča, T.; Kurzhöfer, J.; Kuznik, B.; Laforge, B.; Lamarche, F.; Lander, R.; Landon, M. P. J.; Lange, W.; Lange, W.; Langkau, R.; Lanius, P.; Laporte, J.-F.; Laptin, L.; Laskus, H.; Lebedev, A.; Lemler, M.; Lenhardt, U.; Leuschner, A.; Leverenz, C.; Levonian, S.; Lewin, D.; Ley, Ch.; Lindner, A.; Lindström, G.; Linsel, F.; Lipinski, J.; Liss, B.; Loch, P.; Lodge, A. B.; Lohmander, H.; Lopez, G. C.; Lottin, J.-P.; Lubimov, V.; Ludwig, K.; Lüers, D.; Lugetski, N.; Lundberg, B.; Maeshima, K.; Magnussen, N.; Malinovski, E.; Mani, S.; Marage, P.; Marks, J.; Marshall, R.; Martens, J.; Martin, F.; Martin, G.; Martin, R.; Martyn, H.-U.; Martyniak, J.; Masbender, V.; Masson, S.; Mavroidis, A.; Maxfield, S. J.; McMahon, S. J.; Mehta, A.; Meier, K.; Meissner, J.; Mercer, D.; Merz, T.; Meyer, C. A.; Meyer, H.; Meyer, J.; Mikocki, S.; Mills, J. L.; Milone, V.; Möck, J.; Monnier, E.; Montés, B.; Moreau, F.; Moreels, J.; Morgan, B.; Morris, J. V.; Morton, J. M.; Müller, K.; Murín, P.; Murray, S. A.; Nagovizin, V.; Naroska, B.; Naumann, Th.; Nayman, P.; Nepeipivo, A.; Newman, P.; Newman-Coburn, D.; Newton, D.; Neyret, D.; Nguyen, H. K.; Niebergall, F.; Niebuhr, C.; Nisius, R.; Novák, T.; Nováková, H.; Nowak, G.; Noyes, G. W.; Nyberg, M.; Oberlack, H.; Obrock, U.; Olsson, J. E.; Olszowska, J.; Orenstein, S.; Ould-Saada, F.; Pailler, P.; Palanque, S.; Panaro, E.; Panitch, A.; Parey, J.-Y.; Pascaud, C.; Patel, G. D.; Patoux, A.; Paulot, C.; Pein, U.; Peppel, E.; Perez, E.; Perrodo, P.; Perus, A.; Peters, S.; Pharabod, J.-P.; Phillips, H. T.; Phillips, J. P.; Pichler, Ch.; Pieuchot, A.; Pimpl, W.; Pitzl, D.; Porrovecchio, A.; Prell, S.; Prosi, R.; Quehl, H.; Rädel, G.; Raupach, F.; Rauschnabel, K.; Reboux, A.; Reimer, P.; Reinmuth, G.; Reinshagen, S.; Ribarics, P.; Riech, V.; Riedlberger, J.; Riege, H.; Riess, S.; Rietz, M.; Robertson, S. M.; Robmann, P.; Röpnack, P.; Roosen, R.; Rosenbauer, K.; Rostovtsev, A.; Royon, C.; Rudge, A.; Rüter, K.; Rudowicz, M.; Ruffer, M.; Rusakov, S.; Rusinov, V.; Rybicki, K.; Sacton, J.; Sahlmann, N.; Sanchez, E.; Sankey, D. P. C.; Savitski, M.; Schacht, P.; Schiek, S.; Schirm, N.; Schleif, S.; Schleper, P.; von Schlippe, W.; Schmidt, C.; Schmidt, D.; Schmidt, G.; Schmitz, W.; Schmücker, H.; Schröder, V.; Schütt, J.; Schuhmann, E.; Schulz, M.; Schwind, A.; Scobel, W.; Seehausen, U.; Sefkow, F.; Sell, R.; Seman, M.; Semenov, A.; Shatalov, P.; Shekelyan, V.; Sheviakov, I.; Shooshtari, H.; Shtarkov, L. N.; Siegmon, G.; Siewert, U.; Sirois, Y.; Sirous, A.; Skillicorn, I. O.; Škvařil, P.; Smirnov, P.; Smith, J. R.; Smolik, L.; Sole, D.; Soloviev, Y.; Špalek, J.; Spitzer, H.; von Staa, R.; Staeck, J.; Staroba, P.; Šťastný, J.; Steenbock, M.; Štefan, P.; Steffen, P.; Steinberg, R.; Steiner, H.; Stella, B.; Stephens, K.; Stier, J.; Stiewe, J.; Stösslein, U.; Strachota, J.; Straumann, U.; Strowbridge, A.; Struczinski, W.; Sutton, J. P.; Szkutnik, Z.; Tappern, G.; Tapprogge, S.; Taylor, R. E.; Tchernyshov, V.; Tchudakov, V.; Thiebaux, C.; Thiele, K.; Thompson, G.; Thompson, R. J.; Tichomirov, I.; Trenkel, C.; Tribanek, W.; Tröger, K.; Truöl, P.; Turiot, M.; Turnau, J.; Tutas, J.; Urban, L.; Urban, M.; Usik, A.; Valkár, Š.; Valkárová, A.; Vallée, C.; Van Beek, G.; Vanderkelen, M.; Van Lancker, L.; Van Mechelen, P.; Vartapetian, A.; Vazdik, Y.; Vecko, M.; Verrecchia, P.; Vick, R.; Villet, G.; Vogel, E.; Wacker, K.; Wagener, M.; Walker, I. W.; Walther, A.; Weber, G.; Wegener, D.; Wegner, A.; Weissbach, P.; Wellisch, H. P.; West, L.; White, D.; Willard, S.; Winde, M.; Winter, G.-G.; Wolff, Th.; Womersley, L. A.; Wright, A. E.; Wünsch, E.; Wulff, N.; Wyborn, B. E.; Yiou, T. P.; Žáček, J.; Zarbock, D.; Závada, P.; Zeitnitz, C.; Zhang, Z.; Ziaeepour, H.; Zimmer, M.; Zimmermann, W.; Zomer, F.; Zuber, K.; H1 Collaboration

1997-02-01

Technical aspects of the three major components of the H1 detector at the electron-proton storage ring HERA are described. This paper covers the detector status up to the end of 1994 when a major upgrading of some of its elements was undertaken. A description of the other elements of the detector and some performance figures from luminosity runs at HERA during 1993 and 1994 are given in a paper previously published in this journal.

Isotopic compositions of the elements 2013 (IUPAC Technical Report)

USGS Publications Warehouse

Meija, Juris; Coplen, Tyler B.; Berglund, Michael; Brand, Willi A.; De Bièvre, Paul; Gröning, Manfred; Holden, Norman E.; Irrgeher, Johanna; Loss, Robert D.; Walczyk, Thomas; Prohaska, Thomas

2016-01-01

The Commission on Isotopic Abundances and Atomic Weights (ciaaw.org) of the International Union of Pure and Applied Chemistry (iupac.org) has revised the Table of Isotopic Compositions of the Elements (TICE). The update involved a critical evaluation of the recent published literature. The new TICE 2013 includes evaluated data from the “best measurement” of the isotopic abundances in a single sample, along with a set of representative isotopic abundances and uncertainties that accommodate known variations in normal terrestrial materials.

[Efficient identification and analysis of low and medium frequency repeats]. Progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jurka, J.

1991-08-28

The effective starting date of this grant was May 15. In the first three months of this project we focused primarily on organizational and technical aspects of our research which included: organization of the database of repeats in primates; preparation of software for rapid and sensitive search of novel repetitive elements in GenBank; purchase and installation of the Sun workstation; and research on the mammal-specific MAR1 family of repetitive elements (to be communicated in October).

(Efficient identification and analysis of low and medium frequency repeats)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jurka, J.

1991-08-28

The effective starting date of this grant was May 15. In the first three months of this project we focused primarily on organizational and technical aspects of our research which included: organization of the database of repeats in primates; preparation of software for rapid and sensitive search of novel repetitive elements in GenBank; purchase and installation of the Sun workstation; and research on the mammal-specific MAR1 family of repetitive elements (to be communicated in October).

A Non-Linear Finite Element Model for the Determination of Elastic and Thermal Properties of Nanocomposites

DTIC Science & Technology

2009-04-01

individuals who helped me in many ways throughout my research and thesis writing process. First and foremost, my sincere thanks go to my advisor, Dr... go to Professor John Akin who helped me in the technical areas of Finite Element programming. Thank you for your time and efforts beyond the...classroom. Thank you to Dr. Enrique Barrera and Dr. Jun Lou for serving on my thesis committee. Many thanks go to Dr. Jan Hewitt as well for volunteering

News of Higher Educational Institutions, Ministry of Higher Education USSR, Radiophysics Series

DTIC Science & Technology

1960-12-30

formulate the following proposition: • • 2. " Theorem 2. If the elements AyA ^i (i^t j) of the ; determinant D ,, T*ose diagonal elements...34 OFFICE OF TECHNICAL SERVICES Ü. S. DEPARTMENT OF COMMERCE WASHINGTON 1% D * Ce U. S.’ JOINT PUBLICATIONS RESEARCH SERVICE 1636 CONNECTICUT AVE...N.W. WASHINGTON Z% D , C. FOREWORD "il ELIS publication vas ’.prepared under ■ contract "by the \\JKITED SPATES , JOIET’PUBLICATIONS RE- SEARCH

Direct formation of element chlorides from the corresponding element oxides through microwave-assisted carbohydrochlorination reactions.

PubMed

Nordschild, Simon; Auner, Norbert

2008-01-01

A series of technically and economically important element chlorides-such as SiCl4, BCl3, AlCl3, FeCl2, PCl3 and TiCl4-was synthesized through reactions between hydrogen chloride and the corresponding element oxides in the presence of different carbon sources with microwave assistance. This process route was optimized for demonstration purposes for tetrachlorosilane formation and successfully demonstrates the broad applicability of various silicon oxide-containing minerals and materials for carbohydrochlorination. The chlorination reaction occurs at lower temperatures than with conventional heating in a tubular oven, with substantially shorter reaction times and in better yields: quantitatively in the case of tetrachlorosilane, based on the silicon content of the starting material. The experimental procedure is very simple and provides basic information about the suitability of element compounds, especially element oxides, for carbohydrochlorination. According to the general reaction sequence element oxide-->element-->element chloride used in today's technology, this one-step carbohydrochlorination with hydrogen chloride is considerably more efficient, particularly in terms of energy input and reaction times, avoiding the isolation of the pure elements required for chlorination to give the element chlorides with use of the more corrosive and toxic chlorine gas.

Fundamental Technical Elements of Freeze-fracture/Freeze-etch in Biological Electron Microscopy

EPA Science Inventory

Freeze-fracture/freeze-etch describes a process whereby specimens, typically biological or nanomaterial in nature, are frozen, fractured, and replicated to generate a carbon/platinum "cast" intended for examination by transmission electron microscopy. Specimens are subjected to u...

Review of literature and practices for incident management programs : technical report.

DOT National Transportation Integrated Search

2016-06-01

The project team examined project evaluations, best practice summaries, and synthesis documents, and derived a summary of key elements of programs to speed the time to find and clear stalled vehicles and crashes from freeway shoulders and main lanes....

Implementation elements for conversion of general-purpose freeway lane into high-occupancy-vehicle lane

DOT National Transportation Integrated Search

1997-01-01

Conversion of a general-purpose freeway into a high-occupancy-vehicle (HOV) lane is an alternative to infrastructure addition for HOV system implementation. Research indicates that lane conversion is feasible technically if sufficient HOV usage and m...

LRFD software for design and actual ultimate capacity of confined rectangular columns : [technical summary].

DOT National Transportation Integrated Search

2013-04-01

Columns are considered the most critical elements in structures. The unconfined analysis for columns is well established in the literature. Structural design codes dictate reduction factors for safety. It wasnt until very recently that design spec...

Quality in End User Documentation.

ERIC Educational Resources Information Center

Morrison, Ronald

1994-01-01

Discusses quality in end-user documentation for computer applications and explains four approaches to improving quality in end-user documents. Highlights include online help, usability testing, technical writing elements, statistical approaches, and concepts relating to software quality that are also applicable to user manuals. (LRW)

78 FR 48424 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-08

... Notification AGENCY: Defense Security Cooperation Agency, Department of Defense ACTION: Notice. SUMMARY: The..., personnel training and training equipment, site surveys, Quality Assurance Teams, U.S. Government and... Teams, U.S. Government and contractor technical assistance, and other related elements of program and...

Technical challenges of upset recovery training : simulating the element of surprise

DOT National Transportation Integrated Search

2010-07-30

This invited paper is written in the context of a concerted effort by the aviation industry and regulators to reduce the occurrence of Loss of Control (LOC) accidents. LOC accidents have taken the lead among fatal airplane accidents, recently outpaci...

75 FR 5243 - OST Technical Corrections

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-02

...DOT is making corrections to amendments to a number of its regulations that were published in the Federal Register on June 12, 2008 (73 FR 33326-30) to reflect reorganization of some elements of DOT and the move of DOT's Headquarters site in Washington, DC.

Symbiotic Optimization of Behavior

DTIC Science & Technology

2015-05-01

SYMBIOTIC OPTIMIZATION OF BEHAVIOR UNIVERSITY OF WASHINGTON MAY 2015 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED...2014 4. TITLE AND SUBTITLE SYMBIOTIC OPTIMIZATION OF BEHAVIOR 5a. CONTRACT NUMBER FA8750-12-1-0304 5b. GRANT NUMBER N/A 5c. PROGRAM ELEMENT

Game-theoretic cooperativity in networks of self-interested units

NASA Astrophysics Data System (ADS)

Barto, Andrew G.

1986-08-01

The behavior of theoretical neural networks is often described in terms of competition and cooperation. I present an approach to network learning that is related to game and team problems in which competition and cooperation have more technical meanings. I briefly describe the application of stochastic learning automata to game and team problems and then present an adaptive element that is a synthesis of aspects of stochastic learning automata and typical neuron-like adaptive elements. These elements act as self-interested agents that work toward improving their performance with respect to their individual preference orderings. Networks of these elements can solve a variety of team decision problems, some of which take the form of layered networks in which the ``hidden units'' become appropriate functional components as they attempt to improve their own payoffs.

Theoretical aspects of diagnostics of car as mechatronic system

NASA Astrophysics Data System (ADS)

Goncharov, A. E.; Bondarenko, E. V.; Krasnoshtanov, S. Yu

2018-03-01

The article describes transformation of mechanical systems of automobiles into mechatronic ones due to application of electronic control systems. To assess the relationship of mechanical and electronic components of the mechatronic systems with regard to their technical states, the method of equivalent elements was employed. A mathematical model of changes in the technical state of equivalent elements was developed. It allowed us to present changes in operation capacity in a graphic form. The analytical model is used to ensure operating capacity potential stability for the mechatronic system. For this purpose, new resources were identified with regard to the information ‘field’. Therefore, a new approach to the systematization of knowledge about mechatronic transport systems (D-C-R-E system) is required. The D-C-R-E system is examined as a separate unit. The article describes Information unit formation based on the physical component of the D-C-R-E system and external information which is collected and processed in the Information Diagnostic Center (IDC). Using probability theory and Boolean algebra methods, the authors obtained a logistic model describing information relations between elements of the upgraded D-C-R-E system and contribution of each component to the road safety protection. The logistic model helped formulate main IDC tasks. Implementation of those tasks was transformed into the logical sequence of data collection and analysis in the IDC. That approach predetermined development of the multi-level diagnosing system which made it possible to put in order existing and improved image identification methods and algorithms and to create a diagnosing method for mechatronic systems of cars which reduces labor content and increases accuracy. That approach can help assess the technical state of vehicles with characteristics of mechatronic systems and their transport and environmental safety.

Application of Research on the Metallogenic Background in the Assessment of Mineral Resources Potentiality

NASA Astrophysics Data System (ADS)

Jia, D.; Feng, Y.; Liu, J.; Yao, X.; Zhang, Z.; Ye, T.

2017-12-01

1. Working BackgroundCurrent Status of Geological Prospecting: Detecting boundaries and bottoms, making ore search nearby; Seeing the stars, not seeing the Moon; Deep prospecting, undesirable results. The reasons of these problems are the regional metallogenic backgroud unclear and the metallogenic backgroud of the exploration regions unknown. Accordingly, Development and Research Center, CGS organized a geological setting research, in detail investigate metallogenic geological features and acquire mineralization information. 2. Technical SchemeCore research content is prediction elements of Metallogenic Structure. Adopt unified technical requirements from top to bottom, and technical route from bottom to top; Divide elements of mineral forecast and characteristics of geological structure into five elements for research and expression; Make full use of geophysical, geochemical and remote sensing inferences for the interpretation of macro information. After eight years the great project was completed. 3. Main AchievementsInnovation of basic maps compilation content of geological background, reinforce of geological structure data base of potentiality valuation. Preparation of geotectonic facies maps in different scales and professions, providing brand-new geologic background for potentiality assessment, promoting Chinese geotectonic research to the new height. Preparation of 3,375 geological structure thematic base maps of detecting working area in 6 kinds of prediction methods, providing base working maps, rock assemblage, structure of the protolith of geologic body / mineralization / ore controlling for mineral prediction of 25 ores. Enrichment and development of geotectonic facies analysis method, establishment of metallogenic background research thoughts and approach system for assessment of national mineral resources potentiality for the first time. 4. Application EffectOrientation——More and better results with less effort. Positioning——Have a definite object in view. Heart calm down——Confidence.

Design of case report forms based on a public metadata registry: re-use of data elements to improve compatibility of data.

PubMed

Dugas, Martin

2016-11-29

Clinical trials use many case report forms (CRFs) per patient. Because of the astronomical number of potential CRFs, data element re-use at the design stage is attractive to foster compatibility of data from different trials. The objective of this work is to assess the technical feasibility of a CRF editor with connection to a public metadata registry (MDR) to support data element re-use. Based on the Medical Data Models portal, an ISO/IEC 11179-compliant MDR was implemented and connected to a web-based CRF editor. Three use cases were implemented: re-use at the form, item group and data element levels. CRF design with data element re-use from a public MDR is feasible. A prototypic system is available. The main limitation of the system is the amount of available MDR content.

College Graduation Rates for Minority Students in a Selective Technical University: Will Participation in a Summer Bridge Program Contribute to Success?

PubMed

Murphy, Terrence E; Gaughan, Monica; Hume, Robert; Moore, S Gordon

2010-03-01

There are many approaches to solving the problem of underrepresentation of some racial and ethnic groups and women in scientific and technical disciplines. Here, the authors evaluate the association of a summer bridge program with the graduation rate of underrepresented minority (URM) students at a selective technical university. They demonstrate that this 5-week program prior to the fall of the 1st year contains elements reported as vital for successful student retention. Using multivariable survival analysis, they show that for URM students entering as fall-semester freshmen, relative to their nonparticipating peers, participation in this accelerated summer bridge program is associated with higher likelihood of graduation. The longitudinal panel data include more than 2,200 URM students.

NASA Publications Guide for Authors. Revised

NASA Technical Reports Server (NTRS)

2005-01-01

This document presents guidelines for use by NASA authors for preparing and publishing their scientific and technical information (STI). Section 1 gives an overview. Section 2 describes each type of report in the NASA STI Report Series and other forms of publications. It also discusses dissemination and safeguarding of STI. Section 3 gives technical, data quality, and dissemination reviews, including the mandatory review via NASA Form 1676, NASA Scientific and Technical Information (STI) Document Availability Authorization (DAA). It also describes handling unlimited and limited/restricted STI. Section 4 provides recommended standards for document format, composition, and organization and element of a typical report. Section 5 presents miscellaneous preparation recommendations. Section 6 discusses two required forms, Standard Form 298 and NF-1676. The guide cites additional sources of information of standards, guidelines, and review and approval requirements.

The composing process in technical communications

NASA Technical Reports Server (NTRS)

Hertz, V. L.

1981-01-01

The theoretical construct under which technical writing exercises operate and results from a survey distributed to a random sample of teachers of technical writing are described. The survey, part of a study to develop materials that did not stress prescriptive formats, drew on diverse elements in report writing to enhance writing as a process. Areas of agreement and disagreement related to problem solving, paper evaluation, and individualizing instruction were surveyed. Areas of concern in contemplating the composition process include: (1) the need to create an environment that helps students want to succeed, (2) the role of peer group activity in helping some students who might not respond through lecture or individual study, and (3) encouraging growth in abilities and helping motivate students' interest in writing projects through relevant assignments or simulations students perceive as relevant.

College Graduation Rates for Minority Students in a Selective Technical University: Will Participation in a Summer Bridge Program Contribute to Success?

PubMed Central

Murphy, Terrence E.; Gaughan, Monica; Hume, Robert; Moore, S. Gordon

2012-01-01

There are many approaches to solving the problem of underrepresentation of some racial and ethnic groups and women in scientific and technical disciplines. Here, the authors evaluate the association of a summer bridge program with the graduation rate of underrepresented minority (URM) students at a selective technical university. They demonstrate that this 5-week program prior to the fall of the 1st year contains elements reported as vital for successful student retention. Using multivariable survival analysis, they show that for URM students entering as fall-semester freshmen, relative to their nonparticipating peers, participation in this accelerated summer bridge program is associated with higher likelihood of graduation. The longitudinal panel data include more than 2,200 URM students. PMID:23136456

ATF Neutron Irradiation Program Technical Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geringer, J. W.; Katoh, Yutai

The Japan Atomic Energy Agency (JAEA) under the Civil Nuclear Energy Working Group (CNWG) is engaged in a cooperative research effort with the U.S. Department of Energy (DOE) to explore issues related to nuclear energy, including research on accident-tolerant fuels and materials for use in light water reactors. This work develops a draft technical plan for a neutron irradiation program on the candidate accident-tolerant fuel cladding materials and elements using the High Flux Isotope Reactor (HFIR). The research program requires the design of a detailed experiment, development of test vehicles, irradiation of test specimens, possible post-irradiation examination and characterization ofmore » irradiated materials and the shipment of irradiated materials to JAEA in Japan. This report discusses the technical plan of the experimental study.« less

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra (second from right) talks with workers in the Space Station Processing Facility about the Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. . The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

NASA Image and Video Library

2004-02-03

KENNEDY SPACE CENTER, FLA. - Astronaut Tim Kopra (second from right) talks with workers in the Space Station Processing Facility about the Intravehicular Activity (IVA) constraints testing on the Italian-built Node 2, a future element of the International Space Station. . The second of three Station connecting modules, the Node 2 attaches to the end of the U.S. Lab and provides attach locations for several other elements. Kopra is currently assigned technical duties in the Space Station Branch of the Astronaut Office, where his primary focus involves the testing of crew interfaces for two future ISS modules as well as the implementation of support computers and operational Local Area Network on ISS. Node 2 is scheduled to launch on mission STS-120, Station assembly flight 10A.

California ATMS Testbed : PHASE III: Operational Research Implementation : Final Report [Volume 1: Executive Summary ; and, Volume II: Technical Report

DOT National Transportation Integrated Search

2006-10-01

This report summarizes research and development that has been conducted to position the Testbed to support prototype deployment and evaluation of Advanced Transportation Management Systems (ATMS) products and services. The various elements contained ...

Machine Readable Bibliographic Records: Criteria and Creation.

ERIC Educational Resources Information Center

Bregzis, Ritvars

The centrality of bibliographic records in library automation, objectives of the bibliographic record file and elemental factors involved in bibliographic record creation are discussed. The practical work of creating bibliographic records involves: (1) data base environment, (2) technical aspects, (3) cost and (4) operational methodology. The…

Systems biology, adverse outcome pathways, and ecotoxicology in the 21st century

EPA Science Inventory

While many definitions of systems biology exist, the majority of these contain most (if not all) of the following elements: global measurements of biological molecules to the extent technically feasible, dynamic measurements of key biological molecules to establish quantitative r...

Organizational change: Incentives and resistance

NASA Technical Reports Server (NTRS)

Bishop, Peter C.

1992-01-01

Topics concerning Space Exploration Initiative technical interchange are presented in viewgraph form and include the following: models of change, elements of the current period, the signs of change, leaders' contribution, paradigms - our worldview, paradigm change, the effects of revealing paradigms, a checklist for change, and organizational control.

Identification of Causes and Solution Strategies for Deck Cracking in Jointless Bridges : Technical Report Documentation Page

DOT National Transportation Integrated Search

2012-07-30

Bridges have traditionally relied on a system of expansion joints and flexible bearings to accommodate movements due to temperature, creep, and shrinkage loading. Joints and elements in their vicinity experience a high amount of degradation; thus mod...

Teach the Related Sciences for Graphic Arts

ERIC Educational Resources Information Center

Voss, Lawrence

1974-01-01

At Ferris State College, the chemistry and physics related to the particular skill area of the technically-oriented student are taught. The assumption is that a student will better understand the elements of his trade if his experience is broadened through relevant science information. (KP)

West Germany: Federal Structure, Political Influence.

ERIC Educational Resources Information Center

Toogood, Alex

1978-01-01

Describes the organizational structure of the broadcasting industry in West Germany which is unique because of the federal, public, and political elements involved. Special problems that arise from this framework are discussed, including financing, programing, creative vs technical advances, concepts of production values, and political balance.…

Descriptions of Selected Career-Related College Language Courses

ERIC Educational Resources Information Center

Knodel, Arthur J.; And Others

1977-01-01

Seven courses or programs at different colleges emphasizing specific career applications of languages are described. They include: Technical French; Spanish for Law Enforcement and Correctional Personnel; Executive German; Proyecto Desarrollo Economico; Spanish for Medical Professions; Elements of Foreign Language, and Business French and Business…

Discourse Understanding. Technical Report No. 391.

ERIC Educational Resources Information Center

Scha, R. J. H.; And Others

Artificial intelligence research on natural language understanding is discussed in this report using the notions that (1) natural language understanding systems must "see" sentences as elements whose significance resides in the contribution they make to the larger whole, and (2) a natural language understanding computer system must…

STAR - Copperhead Interface.

DTIC Science & Technology

1981-03-01

elements which fall outside the original box initiate new clusters. 65 ELL. CH ECK This routine provides the calculation which determines if a target...US Air Force Project Rand Report 3-152b-PR, March 197 88 INITIAL DISTRIBUTION LIST 1o. Copies 1. Defense Technical Information Center 2 Cameron

Introspection on improper seismic retrofit of Basilica Santa Maria di Collemaggio after 2009 Italian earthquake

NASA Astrophysics Data System (ADS)

Cimellaro, Gian Paolo; Reinhorn, Andrei M.; de Stefano, Alessandro

2011-03-01

The 2009 L'Aquila, Italy earthquake highlighted the seismic vulnerability of historic masonry building structures due to improper "strengthening" retrofit work that has been done in the last 50 years. Italian seismic standards recommend the use of traditional reinforcement techniques such as replacing the original wooden roof structure with new reinforced concrete (RC) or steel elements, inserting RC tie-beams in the masonry and new RC floors, and using RC jacketing on the shear walls. The L'Aquila earthquake revealed the numerous limitations of these interventions, because they led to increased seismic forces (due to greater additional weight) and to deformation incompatibilities of the incorporated elements with the existing masonry walls. This paper provides a discussion of technical issues pertaining to the seismic retrofit of the Santa Maria di Collemaggio Basilica and in particular, the limitations of the last (2000) retrofit intervention. Considerable damage was caused to the church because of questionable actions and incorrect and improper technical choices.

Two innovative solutions based on fibre concrete blocks designed for building substructure

NASA Astrophysics Data System (ADS)

Pazderka, J.; Hájek, P.

2017-09-01

Using of fibers in a high-strength concrete allows reduction of the dimensions of small precast concrete elements, which opens up new ways of solution for traditional construction details in buildings. The paper presents two innovative technical solutions for building substructure: The special shaped plinth block from fibre concrete and the fibre concrete elements for new technical solution of ventilated floor. The main advantages of plinth block from fibre concrete blocks (compared with standard plinth solutions) is: easier and faster assembly, higher durability and thanks to the air cavity between the vertical part of the block, the building substructure reduced moisture level of structures under the waterproofing layer and a comprehensive solution to the final surface of building plinth as well as the surface of adjacent terrain. The ventilated floor based on fibre concrete precast blocks is an attractive structural alternative for tackling the problem of increased moisture in masonry in older buildings, lacking a functional waterproof layer in the substructure.

LCROSS - Lunar Impactor: Pioneering Risk-Tolerant Exploration in Search for Water on the Moon

NASA Technical Reports Server (NTRS)

Andrews, Daniel R.

2010-01-01

The Lunar CRater Observation and Sensing Satellite (LCROSS) was launched with the Lunar Reconnaissance Orbiter (LRO) on June 18, 2009 to determine the presence of water-ice in a permanently shadowed crater on the south pole of the Moon. However, an equally important purpose was to pioneer low-cost, quick-turnaround NASA missions that could accept a higher-than-normal-level of technical risk. When the LCROSS mission proposal was competitively selected by the NASA Exploration Systems Mission Directorate to design, build, and launch a spacecraft in 31 months with a $79M cost-capped budget and a fixed mass allocation, NASA Ames Research Center and its industry partner, Northrop-Grumman, needed a game-changing approach to be successful. That approach was a ground-breaking combination of having a risk-tolerant NASA Class D mission status and finding the right balance point between the inflexible elements of cost and schedule and the newly-flexible element of technical capability.

Transition Core Properties during Conversion of the NBSR from HEU to LEU Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, A. L.; Diamond, D.

2013-10-31

The transition of the NBSR from HEU to LEU fuel is challenging due to reactivity constraints and the need to maintain an uninterrupted science program, the mission of the NBSR. The transition cannot occur with a full change of HEU to LEU fuel elements since the excess reactivity would be large enough that the NBSR would violate the technical specification for shutdown margin. Manufacturing LEU fuel elements to represent irradiated fuel elements would be cost prohibitive since 26 one-of-a-kind fuel elements would need to be manufactured. For this report a gradual transition from the present HEU fuel to the proposedmore » LEU fuel was studied. The gradual change approach would follow the present fuel management scheme and replace four HEU fuel elements with four LEU fuel elements each cycle. This manuscript reports the results of a series of calculations to predict the neutronic characteristics and how the neutronics will change during the transition from HEU to LEU in the NBSR.« less

Development of high-speed rolling-element bearings. A historical and technical perspective

NASA Technical Reports Server (NTRS)

Zaretsky, E. V.

1982-01-01

Research on large-bore ball and roller bearings for aircraft engines is described. Tapered roller bearings and small-bore bearings are discussed. Temperature capabilities of rolling element bearings for aircraft engines have moved from 450 to 589 K (350 to 600 F) with increased reliability. High bearing speeds to 3 million DN can be achieved with a reliability exceeding that which was common in commercial aircraft. Capabilities of available bearing steels and lubricants were defined and established. Computer programs for the analysis and design of rolling element bearings were developed and experimentally verified. The reported work is a summary of NASA contributions to high performance engine and transmission bearing capabilities.

Trace elements and common ions in southeastern Idaho snow: Regional air pollutant tracers for source area emissions

USGS Publications Warehouse

Abbott, M.; Einerson, J.; Schuster, P.; Susong, D.; Taylor, Howard E.; ,

2004-01-01

Snow sampling and analysis methods which produce accurate and ultra-low measurements of trace elements and common ion concentration in southeastern Idaho snow, were developed. Snow samples were collected over two winters to assess trace elements and common ion concentrations in air pollutant fallout across the southeastern Idaho. The area apportionment of apportionment of fallout concentrations measured at downwind location were investigated using pattern recognition and multivariate statistical technical techniques. Results show a high level of contribution from phosphates processing facilities located outside Pocatello in the southern portion of the Eastern Snake River Plain, and no obvious source area profiles other than at Pocatello.

Atomic weights of the elements 2011 (IUPAC Technical Report)

USGS Publications Warehouse

Wieser, Michael E.; Holden, Norman; Coplen, Tyler B.; Böhlke, John K.; Berglund, Michael; Brand, Willi A.; De Bièvre, Paul; Gröning, Manfred; Loss, Robert D.; Meija, Juris; Hirata, Takafumi; Prohaska, Thomas; Schoenberg, Ronny; O'Connor, Glenda; Walczyk, Thomas; Yoneda, Shige; Zhu, Xiang-Kun

2013-01-01

The biennial review of atomic-weight determinations and other cognate data has resulted in changes for the standard atomic weights of five elements. The atomic weight of bromine has changed from 79.904(1) to the interval [79.901, 79.907], germanium from 72.63(1) to 72.630(8), indium from 114.818(3) to 114.818(1), magnesium from 24.3050(6) to the interval [24.304, 24.307], and mercury from 200.59(2) to 200.592(3). For bromine and magnesium, assignment of intervals for the new standard atomic weights reflects the common occurrence of variations in the atomic weights of those elements in normal terrestrial materials.

Ground Vibration Testing Options for Space Launch Vehicles

NASA Technical Reports Server (NTRS)

Patterson, Alan; Smith, Robert K.; Goggin, David; Newsom, Jerry

2011-01-01

New NASA launch vehicles will require development of robust systems in a fiscally-constrained environment. NASA, Department of Defense (DoD), and commercial space companies routinely conduct ground vibration tests as an essential part of math model validation and launch vehicle certification. Although ground vibration testing must be a part of the integrated test planning process, more affordable approaches must also be considered. A study evaluated several ground vibration test options for the NASA Constellation Program flight test vehicles, Orion-1 and Orion-2, which concluded that more affordable ground vibration test options are available. The motivation for ground vibration testing is supported by historical examples from NASA and DoD. The approach used in the present study employed surveys of ground vibration test subject-matter experts that provided data to qualitatively rank six test options. Twenty-five experts from NASA, DoD, and industry provided scoring and comments for this study. The current study determined that both element-level modal tests and integrated vehicle modal tests have technical merits. Both have been successful in validating structural dynamic math models of launch vehicles. However, element-level testing has less overall cost and schedule risk as compared to integrated vehicle testing. Future NASA launch vehicle development programs should anticipate that some structural dynamics testing will be necessary. Analysis alone will be inadequate to certify a crew-capable launch vehicle. At a minimum, component and element structural dynamic tests are recommended for new vehicle elements. Three viable structural dynamic test options were identified. Modal testing of the new vehicle elements and an integrated vehicle test on the mobile launcher provided the optimal trade between technical, cost, and schedule.

Configuration Management Plan for the Tank Farm Contractor

DOE Office of Scientific and Technical Information (OSTI.GOV)

WEIR, W.R.

The Configuration Management Plan for the Tank Farm Contractor describes configuration management the contractor uses to manage and integrate its technical baseline with the programmatic and functional operations to perform work. The Configuration Management Plan for the Tank Farm Contractor supports the management of the project baseline by providing the mechanisms to identify, document, and control the technical characteristics of the products, processes, and structures, systems, and components (SSC). This plan is one of the tools used to identify and provide controls for the technical baseline of the Tank Farm Contractor (TFC). The configuration management plan is listed in themore » management process documents for TFC as depicted in Attachment 1, TFC Document Structure. The configuration management plan is an integrated approach for control of technical, schedule, cost, and administrative processes necessary to manage the mission of the TFC. Configuration management encompasses the five functional elements of: (1) configuration management administration, (2) configuration identification, (3) configuration status accounting, (4) change control, and (5 ) configuration management assessments.« less

Stimulation of dendrogenesis and neural maturation in adult mammals.

PubMed

Soto-Vázquez, Ramón; Labastida-López, Carlos; Romero-Castello, Samuel; Benítez-King, Gloria; Parra-Cervantes, Patricia

2016-05-01

This work is the result of a technical research patent on dendritogenesis and neuronal maturation, in which the existence was determined of patent documents involving the use of melatonin for the treatment of anxiety, obesity and related diseases of the peripheral and CNS. In this study, an analysis of the state of the art in order to collect technical and scientific elements for the drafting of a new patent on the use of the melatonin molecule in stimulating neuronal maturation in dendritogenesis and mammals was conducted in adults. This study is based on an invention related with this novel use of melatonin.

Design of impact-resistant boron/aluminum large fan blade

NASA Technical Reports Server (NTRS)

Salemme, C. T.; Yokel, S. A.

1978-01-01

The technical program was comprised of two technical tasks. Task 1 encompassed the preliminary boron/aluminum fan blade design effort. Two preliminary designs were evolved. An initial design consisted of 32 blades per stage and was based on material properties extracted from manufactured blades. A final design of 36 blades per stage was based on rule-of-mixture material properties. In Task 2, the selected preliminary blade design was refined via more sophisticated analytical tools. Detailed finite element stress analysis and aero performance analysis were carried out to determine blade material frequencies and directional stresses.

33 CFR 385.30 - Master Implementation Sequencing Plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Incorporating New Information Into the Plan § 385.30 Master Implementation Sequencing Plan. (a) Not later than... projects of the Plan, including pilot projects and operational elements, based on the best scientific, technical, funding, contracting, and other information available. The Corps of Engineers and the South...

Total Quality Management Implementation at the Defense Technical Information Center

DTIC Science & Technology

1989-09-01

industry user groups, as well as the contracting process to emphasize the benefits of TQM to the private sector . 5. Demonstrate an Uncompromising... worklife enhancements are important elements in creating the environment in which DTIC personnel will grow, gain new experiences and capabilities, and

Component-Based Approach in Learning Management System Development

ERIC Educational Resources Information Center

Zaitseva, Larisa; Bule, Jekaterina; Makarov, Sergey

2013-01-01

The paper describes component-based approach (CBA) for learning management system development. Learning object as components of e-learning courses and their metadata is considered. The architecture of learning management system based on CBA being developed in Riga Technical University, namely its architecture, elements and possibilities are…

Man-systems distributed system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Lewis, J. L.

1990-01-01

Viewgraphs on man-systems distributed system for Space Station Freedom are presented. Topics addressed include: description of man-systems (definition, requirements, scope, subsystems, and topologies); implementation (approach, tools); man-systems interfaces (system to element and system to system); prime/supporting development relationship; selected accomplishments; and technical challenges.

Report on Assessment of Work Atmosphere.

ERIC Educational Resources Information Center

Platte Technical Community Coll., Columbus, NE.

Seven sets of fifteen bi-polar adjectives corresponding to seven elements of organizational climate were compiled as a testing instrument which was administered to 124 working personnel at Platte Technical Community College in the fall of 1975. Respondents included faculty, students, support staff, and administrative personnel. Analysis of the…

Creating a Collaborative Environment: Instructional and Learning Services

ERIC Educational Resources Information Center

David Diedriech; Lynda LaRoche

2005-01-01

Instructional technology consists of many elements, including information technology, knowledge of pedagogy and faculty needs, technical support, and training. DePauw University has recently reorganized its Information Services staff to include several staff areas, including technicians, library staff and help desk, as well as faculty support…

Acronyms, initialisms, and abbreviations: Fourth Revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolman, B.J.

1994-04-01

This document lists acronyms used in technical writing. The immense list is supplemented by an appendix containing chemical elements, classified information access, common abbreviations used for functions, conversion factors for selected SI units, a flowcharting template, greek alphabet, metrix terminology, proofreader`s marks, signs and symbols, and state abbreviations.

Administrative Utility Analysis: Appendices.

ERIC Educational Resources Information Center

Peat, Marwick, Mitchell and Co., San Juan, Puerto Rico.

Appendixes to a study on administrative utility analysis and vocational education programs for the Area of Vocational and Technical Education (AVTE) in the Puerto Rico Department of Education contain the planning and budgeting system elements, position descriptions, and information on the growth of vocational education in Puerto Rico. The elements…

Erratum to Dynamic stresses, Coulomb failure, and remote triggering and to Surface wave potential for triggering tectonic (nonvolcanic) tremor

USGS Publications Warehouse

Hill, David P.

2012-01-01

Hill (2008) and Hill (2010) contain two technical errors: (1) a missing factor of 2 for computed Love‐wave amplitudes, and (2) a sign error in the off‐diagonal elements in the Euler rotation matrix.

48 CFR 2937.602 - Elements of performance-based contracting.

Code of Federal Regulations, 2010 CFR

2010-10-01

... objectively measurable incentives (e.g., Firm-Fixed-Price, Fixed-Price-Incentive-Fee, or Cost-Plus-Incentive-Fee) is appropriate. However, when contractor performance (e.g., cost control, schedule, or quality/technical) is best evaluated subjectively using qualitative measures, a Cost-Plus-Award-Fee contract may be...

An Architecture for Learning in Projects?

ERIC Educational Resources Information Center

Sense, Andrew J.

2004-01-01

This paper reports upon a two-year, qualitative, case study action research investigation into "learning within a project team". This project team undertook a significant socio-technical redesign project within a major Australian heavy engineering/manufacturing operation. The paper identifies and elaborates upon a number of elements that…

Management/Technical Interaction in Integrated Information System Development.

ERIC Educational Resources Information Center

Bagley, Clarence H.; Gardner, Don E.

The integrated information system element of the management information system concept has practical applications for management in the areas of both information analysis and decision-model building. Four basic options for achieving integration in operational data systems are: a default option, the coordinated file option, the distributed…

The Use of Instructor-Patients to Teach Physical Examination Techniques

ERIC Educational Resources Information Center

Anderson, Karen K.; Meyer, Thomas C.

1978-01-01

Sixteen community residents with relatively stable respiratory, cardiovascular, musculoskeletal, or neurological findings were recruited and trained as instructor-patients to teach the technical elements of the examination of an affected organ system. Faculty recruitment, instructor-patient recruitment and training, and evaluation are discussed.…

PolyPole-1: An accurate numerical algorithm for intra-granular fission gas release

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pizzocri, D.; Rabiti, C.; Luzzi, L.

2016-09-01

This paper describes the development of a new numerical algorithm (called PolyPole-1) to efficiently solve the equation for intra-granular fission gas release in nuclear fuel. The work was carried out in collaboration with Politecnico di Milano and Institute for Transuranium Elements. The PolyPole-1 algorithms is being implemented in INL's fuels code BISON code as part of BISON's fission gas release model. The transport of fission gas from within the fuel grains to the grain boundaries (intra-granular fission gas release) is a fundamental controlling mechanism of fission gas release and gaseous swelling in nuclear fuel. Hence, accurate numerical solution of themore » corresponding mathematical problem needs to be included in fission gas behaviour models used in fuel performance codes. Under the assumption of equilibrium between trapping and resolution, the process can be described mathematically by a single diffusion equation for the gas atom concentration in a grain. In this work, we propose a new numerical algorithm (PolyPole-1) to efficiently solve the fission gas diffusion equation in time-varying conditions. The PolyPole-1 algorithm is based on the analytic modal solution of the diffusion equation for constant conditions, with the addition of polynomial corrective terms that embody the information on the deviation from constant conditions. The new algorithm is verified by comparing the results to a finite difference solution over a large number of randomly generated operation histories. Furthermore, comparison to state-of-the-art algorithms used in fuel performance codes demonstrates that the accuracy of the PolyPole-1 solution is superior to other algorithms, with similar computational effort. Finally, the concept of PolyPole-1 may be extended to the solution of the general problem of intra-granular fission gas diffusion during non-equilibrium trapping and resolution, which will be the subject of future work.« less

Chemistry of transuranium elements in salt-base repository

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borkowski, Marian; Reed, Donald T; Lucchini, Jean - Francois

2010-12-02

The mobility and potential release of actinides into the accessible environment continues to be the key performance assessment concern of nuclear repositories. Actinide, in particular plutonium speciation under the wide range of conditions that can exist in the subsurface is complex and depends strongly on the coupled effects of redox conditions, inorganic/organic complexation, and the extent/nature of aggregation. Understanding the key factors that define the potential for actinide migration is, in this context, an essential and critical part of making and sustaining a licensing case for a nuclear repository. Herein we report on recent progress in a concurrent modeling andmore » experimental study to determine the speciation of plutonium, uranium and americium in high ionic strength Na-CI-Mg brines. This is being done as part of the ongomg recertification effort m the Waste Isolation Pilot Plant (WIPP). The oxidation-state specific solubility of actinides were established in brine as function of pC{sub H+}, brine composition and the presence and absence of organic chelating agents and carbonate. An oxidation-state invariant analog approach using Nd{sup 3+} and Th{sup 4+} was used for An{sup 3+} and An{sup 4+} respectively. These results show that organic ligands and hydrolysis are key factors for An(III) solubility, hydrolysis at pC{sub H+} above 8 is predominate for An(IV) and carbonates are the key factor for U(VI) solubility. The effect of high ionic strength and brine components measured in absence of carbonates leads to measurable increased in overall solubility over analogous low ionic strength groundwater. Less is known about the bioreduction of actinides by halo-tolerant microorganisms, but there is now evidence that bioreduction does occur and is analogous, in many ways, to what occurs with soil bacteria. Results of solubility studies that focus on Pitzer parameter corrections, new species (e.g. borate complexation), and the thermodynamic parameters for modeling are discussed.« less

Degradation Factor Approach for Impacted Composite Structural Assessment: MSFC Center Director's Discretionary Fund Final Report, Project No. 96-17

NASA Technical Reports Server (NTRS)

Ortega, R.; Price, J. M.; Fox, D.

2000-01-01

This technical memorandum documents the results of the research to develop a concept for assessing the structural integrity of impacted composite structures using the strength degradation factor in conjunction with available finite element tools. For this purpose, a literature search was conducted, a plan for conducting impact testing on two laminates was developed, and a finite element model of the impact process was created. Specimens for the impact testing were fabricated to support the impact testing plan.

Surface hardening of cutting elements agricultural machinery vibro arc plasma

NASA Astrophysics Data System (ADS)

Sharifullin, S. N.; Adigamov, N. R.; Adigamov, N. N.; Solovev, R. Y.; Arakcheeva, K. S.

2016-01-01

At present, the state technical policy aimed at the modernization of worn equipment, including agriculture, based on the use of high-performance technology called nanotechnology. By upgrading worn-out equipment meant restoring it with the achievement of the above parameters passport. The existing traditional technologies are not suitable for the repair of worn-out equipment modernization. This is especially true of imported equipment. Out here alone - is the use of high-performance technologies. In this paper, we consider the use of vibro arc plasma for surface hardening of cutting elements of agricultural machinery.

Mg-perovskite/silicate melt and magnesiowuestite/silicate melt partition coefficients for KLB-1 at 250 Kbars

NASA Technical Reports Server (NTRS)

Drake, Michael J.; Rubie, David C.; Mcfarlane, Elisabeth A.

1992-01-01

The partitioning of elements amongst lower mantle phases and silicate melts is of interest in unraveling the early thermal history of the Earth. Because of the technical difficulty in carrying out such measurements, only one direct set of measurements was reported previously, and these results as well as interpretations based on them have generated controversy. Here we report what are to our knowledge only the second set of directly measured trace element partition coefficients for a natural system (KLB-1).

[Structural elements of critical thinking of nurses in emergency care].

PubMed

Crossetti, Maria da Graça Oliveira; Bittencourt, Greicy Kelly Gouveia Dias; Lima, Ana Amélia Antunes; de Góes, Marta Georgina Oliveira; Saurin, Gislaine

2014-09-01

The objective of this study was to analyze the structural elements of critical thinking (CT) of nurses in the clinical decision-making process. This exploratory, qualitative study was conducted with 20 emergency care nurses in three hospitals in southern Brazil. Data were collected from April to June 2009, and a validated clinical case was applied from which nurses listed health problems, prescribed care and listed the structural elements of CT. Content analysis resulted in categories used to determine priority structural elements of CT, namely theoretical foundations and practical relationship to clinical decision making; technical and scientific knowledge and clinical experience, thought processes and clinical decision making: clinical reasoning and basis for clinical judgments of nurses: patient assessment and ethics. It was concluded that thinking critically is a skill that enables implementation of a secure and effective nursing care process.

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis Project

NASA Technical Reports Server (NTRS)

1988-01-01

Fiscal year 1987 research activities and accomplishments for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division are presented. The project's technical activities were organized into three work elements. The Molecular Modeling and Applied Genetics work element includes modeling and simulation studies to verify a dynamic model of the enzyme carboxypeptidase; plasmid stabilization by chromosomal integration; growth and stability characteristics of plasmid-containing cells; and determination of optional production parameters for hyper-production of polyphenol oxidase. The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields, and lower separation energetics. The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the economics and energetics of a given biocatalyst process.

Data precision of X-ray fluorescence (XRF) scanning of discrete samples with the ITRAX XRF core-scanner exemplified on loess-paleosol samples

NASA Astrophysics Data System (ADS)

Profe, Jörn; Ohlendorf, Christian

2017-04-01

XRF-scanning is the state-of-the-art technique for geochemical analyses in marine and lacustrine sedimentology for more than a decade. However, little attention has been paid to data precision and technical limitations so far. Using homogenized, dried and powdered samples (certified geochemical reference standards and samples from a lithologically-contrasting loess-paleosol sequence) minimizes many adverse effects that influence the XRF-signal when analyzing wet sediment cores. This allows the investigation of data precision under ideal conditions and documents a new application of the XRF core-scanner technology at the same time. Reliable interpretations of XRF results require data precision evaluation of single elements as a function of X-ray tube, measurement time, sample compaction and quality of peak fitting. Ten-fold measurement of each sample constitutes data precision. Data precision of XRF measurements theoretically obeys Poisson statistics. Fe and Ca exhibit largest deviations from Poisson statistics. The same elements show the least mean relative standard deviations in the range from 0.5% to 1%. This represents the technical limit of data precision achievable by the installed detector. Measurement times ≥ 30 s reveal mean relative standard deviations below 4% for most elements. The quality of peak fitting is only relevant for elements with overlapping fluorescence lines such as Ba, Ti and Mn or for elements with low concentrations such as Y, for example. Differences in sample compaction are marginal and do not change mean relative standard deviation considerably. Data precision is in the range reported for geochemical reference standards measured by conventional techniques. Therefore, XRF scanning of discrete samples provide a cost- and time-efficient alternative to conventional multi-element analyses. As best trade-off between economical operation and data quality, we recommend a measurement time of 30 s resulting in a total scan time of 30 minutes for 30 samples.

The Role of Project Science in the Chandra X-Ray Observatory

NASA Technical Reports Server (NTRS)

O'Dell, Stephen L.; Weisskopf, Martin C.

2006-01-01

The Chandra X-Ray Observatory, one of NASA's Great Observatories, has an outstanding record of scientific and technical success. This success results from the efforts of a team comprising NASA, its contractors, the Smithsonian Astrophysical Observatory, the instrument groups, and other elements of the scientific community, including thousands of scientists who utilize this powerful facility for astrophysical research. We discuss the role of NASA Project Science in the formulation, development, calibration, and operation of the Chandra X-ray Observatory. In addition to representing the scientific community within the Project, Project Science performed what we term "science systems engineering". This activity encompasses translation of science requirements into technical requirements and assessment of the scientific impact of programmatic and technical trades. We briefly describe several examples of science systems engineering conducted by Chandra Project Science.

Exploration Medical System Technical Development

NASA Technical Reports Server (NTRS)

McGuire, K.; Middour, C.; Cerro, J.; Burba, T.; Hanson, A.; Reilly, J.; Mindock, J.

2017-01-01

The Exploration Medical Capability (ExMC) Element systems engineering goals include defining the technical system needed to implement exploration medical capabilities for Mars. This past year, scenarios captured in the medical system concept of operations laid the foundation for systems engineering technical development work. The systems engineering team analyzed scenario content to identify interactions between the medical system, crewmembers, the exploration vehicle, and the ground system. This enabled the definition of functions the medical system must provide and interfaces to crewmembers and other systems. These analyses additionally lead to the development of a conceptual medical system architecture. The work supports the ExMC community-wide understanding of the functional exploration needs to be met by the medical system, the subsequent development of medical system requirements, and the system verification and validation approach utilizing terrestrial analogs and precursor exploration missions.

A socio-technical critique of tiered services: implications for interprofessional care.

PubMed

Hood, Rick

2015-01-01

In the health and social care sector, tiered services have become an increasingly influential way of organising professional expertise to address the needs of vulnerable people. Drawing on its application to UK child welfare services, this paper discusses the merits of the tiered model from a socio-technical perspective - an approach that has emerged from the fields of accident analysis and systems design. The main elements of a socio-technical critique are outlined and used to explore how tiered services provide support to families and prevent harm to children. Attention is drawn to the distribution of expertise and resources in a tiered system, and to the role of referral and gate-keeping procedures in dispersing accountability for outcomes. An argument is made for designing systems "against demand", and the paper concludes by discussing some alternative models of multi-agency provision.

The strategic relevance of manufacturing technology: An overall quality concept to promote innovation preventing drug shortage.

PubMed

Panzitta, Michele; Ponti, Mauro; Bruno, Giorgio; Cois, Giancarlo; D'Arpino, Alessandro; Minghetti, Paola; Mendicino, Francesca Romana; Perioli, Luana; Ricci, Maurizio

2017-01-10

Manufacturing is the bridge between research and patient: without product, there is no clinical outcome. Shortage has a variety of causes, in this paper we analyse only causes related to manufacturing technology and we use shortage as a paradigm highliting the relevance of Pharmaceutical Technology. Product and process complexity and capacity issues are the main challenge for the Pharmaceutical Industry Supply chain. Manufacturing Technology should be acknowledged as a R&D step and as a very important matter during University degree in Pharmacy and related disciplines, promoting collaboration between Academia and Industry, measured during HTA step and rewarded in terms of price and reimbursement. The above elements are not yet properly recognised, and manufacturing technology is taken in to consideration only when a shortage is in place. In a previous work, Panzitta et al. proposed to perform a full technology assessment at the Health Technological Assessment stage, evaluating three main technical aspects of a medicine: manufacturing process, physicochemical properties, and formulation characteristics. In this paper, we develop the concept of manufacturing appraisal, providing a technical overview of upcoming challenges, a risk based approach and an economic picture of shortage costs. We develop also an overall quality concept, not limited to GMP factors but broaden to all elements leading to a robust supply and promoting technical innovation. Copyright © 2016 Elsevier B.V. All rights reserved.

77 FR 53180 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-31

... logistical and program support. (iv) Military Department: Air Force (CCZ, Amd 7). (v) Prior Related Cases, if.... Government and contractor technical and logistics support services; and other related elements of logistical and program support. The estimated cost is $850 million. This proposed sale will contribute to the...

Sixteenth NASTRAN (R) Users' Colloquium

NASA Technical Reports Server (NTRS)

1988-01-01

These are the proceedings of the Sixteenth NASTRAN Users' Colloquium held in Arlington, Virginia from 25 to 29 April, 1988. Technical papers contributed by participants review general application of finite element methodology and the specific application of the NASA Structural Analysis System (NASTRAN) to a variety of static and dynamic structural problems.

Sensitivity of the International Skating Union's Mathematical Criteria to Flag Potential Scoring Anomalies

ERIC Educational Resources Information Center

Looney, Marilyn A.; Howell, Steven M.

2015-01-01

This article describes the "mathematical criteria" employed by the International Skating Union (ISU) to identify potential judging anomalies within competitive figure skating. The mathematical criteria have greater sensitivity to identify scoring anomalies for technical element scores than for the program component scores. This article…

Utilizing Motivational Interviewing to Address Resistant Behaviors in Clinical Supervision

ERIC Educational Resources Information Center

Wahesh, Edward

2016-01-01

Motivational interviewing is presented as an approach to address resistant behaviors in clinical supervision. A case example is used to illustrate the process in which the relational and technical elements of motivational interviewing can be applied to supervisee resistance. Implications for supervisors and researchers are discussed.

78 FR 75571 - Independent Assessment of the Process for the Review of Device Submissions; High Priority...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-12

... of performing the technical analysis, management assessment, and program evaluation tasks required to.... Analysis of elements of the review process (including the presubmission process, and investigational device... time to facilitate a more efficient process. This includes analysis of root causes for inefficiencies...

Communicating Environment, Health, and Safety Information to Internal and External Audiences.

ERIC Educational Resources Information Center

Davis, Thomas S.

1995-01-01

Argues that today's corporation must keep informed a wide range of individuals who have a stake in environment, health, and safety issues. Describes four elements of an effective communications program for doing so: electronic media to communicate technical information, environmental and safety audits, public communications with company…

Merit Pay and Faculty Evaluation.

ERIC Educational Resources Information Center

Hudgins, James L.

A program linking merit pay and faculty evaluation was initiated at Sumter Area Technical College (SATC) in Sumter, South Carolina, in 1978. The performance-based evaluation system focuses on three elements: the job description, which identifies professional responsibilities and how they relate to the college's mission; the individual action plan;…

A Legacy of Learning

ERIC Educational Resources Information Center

Reese, Susan

2011-01-01

Apprenticeships are a time-honored way of passing along skills in an art, trade, or craft. Apprenticeships have long been an important element of career and technical education (CTE). From automotive technology to the construction trades to the culinary arts and beyond, community colleges across the nation are still using apprenticeships to…

Using Strategic Planning To Improve Rural Schools.

ERIC Educational Resources Information Center

D'Amico, Joseph J.

This paper describes the elements of strategic planning and applies them to educational reform and improvement. The paper also describes how a planning model, Strategic Planning for Educational Reform and Improvement (SPERI), was used by Rural Assistance Councils (RACs) in Pennsylvania and Delaware, with technical assistance from Research for…

Issues in Engineering Self-Aware and Self-Expressive Ensembles

NASA Astrophysics Data System (ADS)

Hölzl, Matthias; Wirsing, Martin

The following sections are included: * Introduction * Classifying Awareness and Self-Expression * Elements of the awareness mechanism * A white-box definition of awareness * Self-expression * A black-box definition of awareness * Awareness Engineering * Socio-Technical Issues * Privacy, ownership and control of data * Discrimination and responsibility * Failuremodes * Summary and Conclusions

10 CFR 52.47 - Contents of applications; technical information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accidents, e.g., challenges to containment integrity caused by core-concrete interaction, steam explosion... such as the service water intake structure and the ultimate heat sink; (2) An application for... design except for site-specific elements such as the service water intake structure and the ultimate heat...

10 CFR 52.47 - Contents of applications; technical information.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accidents, e.g., challenges to containment integrity caused by core-concrete interaction, steam explosion... such as the service water intake structure and the ultimate heat sink; (2) An application for... design except for site-specific elements such as the service water intake structure and the ultimate heat...

10 CFR 52.47 - Contents of applications; technical information.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accidents, e.g., challenges to containment integrity caused by core-concrete interaction, steam explosion... such as the service water intake structure and the ultimate heat sink; (2) An application for... design except for site-specific elements such as the service water intake structure and the ultimate heat...

10 CFR 52.47 - Contents of applications; technical information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... accidents, e.g., challenges to containment integrity caused by core-concrete interaction, steam explosion... such as the service water intake structure and the ultimate heat sink; (2) An application for... design except for site-specific elements such as the service water intake structure and the ultimate heat...

10 CFR 52.47 - Contents of applications; technical information.

Code of Federal Regulations, 2012 CFR

2012-01-01

... accidents, e.g., challenges to containment integrity caused by core-concrete interaction, steam explosion... such as the service water intake structure and the ultimate heat sink; (2) An application for... design except for site-specific elements such as the service water intake structure and the ultimate heat...

Comparing Powerpoint Experts' and University Students' Opinions about Powerpoint Presentations

ERIC Educational Resources Information Center

Mackiewicz, Jo

2008-01-01

Technical communication instructors want to help students, as well as professionals, design effective PowerPoint presentations. Toward this end, I compare the advice of academic and industry experts about effective PowerPoint presentation design to survey responses from university students about slide text, visual elements, animations, and other…

Joining Together for a Common Cause – Interagency Collaboration to Fight disease

USDA-ARS?s Scientific Manuscript database

In addition to the economic and technical benefits of technology transfer, there is the human element-how technology development and technology transfer can make a difference in people’s lives. We will share compelling stories of how individuals have directly benefited from technology development an...

First International Symposium on Strain Gauge Balances. Pt. 1

NASA Technical Reports Server (NTRS)

Tripp, John S. (Editor); Tcheng, Ping (Editor)

1999-01-01

The first International Symposium on Strain Gauge Balances was sponsored and held at NASA Langley Research Center during October 22-25, 1996. The symposium provided an open international forum for presentation, discussion, and exchange of technical information among wind tunnel test technique specialists and strain gauge balance designers. The Symposium also served to initiate organized professional activities among the participating and relevant international technical communities. Over 130 delegates from 15 countries were in attendance. The program opened with a panel discussion, followed by technical paper sessions, and guided tours of the National Transonic Facility (NTF) wind tunnel, a local commercial balance fabrication facility, and the LaRC balance calibration laboratory. The opening panel discussion addressed "Future Trends in Balance Development and Applications." Forty-six technical papers were presented in 11 technical sessions covering the following areas: calibration, automatic calibration, data reduction, facility reports, design, accuracy and uncertainty analysis, strain gauges, instrumentation, balance design, thermal effects, finite element analysis, applications, and special balances. At the conclusion of the Symposium, a steering committee representing most of the nations and several U.S. organizations attending the Symposium was established to initiate planning for a second international balance symposium, to be held in 1999 in the UK.

E-KIT: An Electronic-Knowledge Information Tool for Organizing Site Information and Improving Technical Communication with Stakeholders - 13082

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kautsky, Mark; Findlay, Richard C.; Hodges, Rex A.

2013-07-01

Managing technical references for projects that have long histories is hampered by the large collection of documents, each of which might contain discrete pieces of information relevant to the site conceptual model. A database application has been designed to improve the efficiency of retrieving technical information for a project. Although many databases are currently used for accessing analytical and geo-referenced data, applications designed specifically to manage technical reference material for projects are scarce. Retrieving site data from the array of available references becomes an increasingly inefficient use of labor. The electronic-Knowledge Information Tool (e-KIT) is designed as a project-level resourcemore » to access and communicate technical information. The e-KIT is a living tool that grows as new information becomes available, and its value to the project increases as the volume of site information increases. Having all references assembled in one location with complete reference citations and links to elements of the site conceptual model offers a way to enhance communication with outside groups. The published and unpublished references are incorporated into the e-KIT, while the compendium of references serves as a complete bibliography for the project. (authors)« less

First International Symposium on Strain Gauge Balances. Part 2

NASA Technical Reports Server (NTRS)

Tripp, John S (Editor); Tcheng, Ping (Editor)

1999-01-01

The first International Symposium on Strain Gauge Balances was sponsored and held at NASA Langley Research Center during October 22-25, 1996. The symposium provided an open international forum for presentation, discussion, and exchange of technical information among wind tunnel test technique specialists and strain gauge balance designers. The Symposium also served to initiate organized professional activities among the participating and relevant international technical communities. Over 130 delegates from 15 countries were in attendance. The program opened with a panel discussion, followed by technical paper sessions, and guided tours of the National Transonic Facility (NTF) wind tunnel, a local commercial balance fabrication facility, and the LaRC balance calibration laboratory. The opening panel discussion addressed "Future Trends in Balance Development and Applications." Forty-six technical papers were presented in 11 technical sessions covering the following areas: calibration, automatic calibration, data reduction, facility reports, design, accuracy and uncertainty analysis, strain gauges, instrumentation, balance design, thermal effects, finite element analysis, applications, and special balances. At the conclusion of the Symposium, a steering committee representing most of the nations and several U.S. organizations attending the Symposium was established to initiate planning for a second international balance symposium, to be held in 1999 in the UK.

Multi-element germanium detectors for synchrotron applications

DOE PAGES

Rumaiz, A. K.; Kuczewski, A. J.; Mead, J.; ...

2018-04-27

In this paper, we have developed a series of monolithic multi-element germanium detectors, based on sensor arrays produced by the Forschungzentrum Julich, and on Application-specific integrated circuits (ASICs) developed at Brookhaven. Devices have been made with element counts ranging from 64 to 384. These detectors are being used at NSLS-II and APS for a range of diffraction experiments, both monochromatic and energy-dispersive. Compact and powerful readout systems have been developed, based on the new generation of FPGA system-on-chip devices, which provide closely coupled multi-core processors embedded in large gate arrays. Finally, we will discuss the technical details of the systems,more » and present some of the results from them.« less

NASA's new university engineering space research programs

NASA Technical Reports Server (NTRS)

Sadin, Stanley R.

1988-01-01

The objective of a newly emerging element of NASA's university engineering programs is to provide a more autonomous element that will enhance and broaden the capabilities in academia, enabling them to participate more effectively in the U.S. civil space program. The programs utilize technical monitors at NASA centers to foster collaborative arrangements, exchange of personnel, and the sharing of facilities between NASA and the universities. The elements include: the university advanced space design program, which funds advanced systems study courses at the senior and graduate levels; the university space engineering research program that supports cross-disciplinary research centers; the outreach flight experiments program that offers engineering research opportunities to universities; and the planned university investigator's research program to provide grants to individuals with outstanding credentials.

Multi-element germanium detectors for synchrotron applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rumaiz, A. K.; Kuczewski, A. J.; Mead, J.

In this paper, we have developed a series of monolithic multi-element germanium detectors, based on sensor arrays produced by the Forschungzentrum Julich, and on Application-specific integrated circuits (ASICs) developed at Brookhaven. Devices have been made with element counts ranging from 64 to 384. These detectors are being used at NSLS-II and APS for a range of diffraction experiments, both monochromatic and energy-dispersive. Compact and powerful readout systems have been developed, based on the new generation of FPGA system-on-chip devices, which provide closely coupled multi-core processors embedded in large gate arrays. Finally, we will discuss the technical details of the systems,more » and present some of the results from them.« less

Overview of Marshall Space Flight Center Activities for the Combustion Stability Tool Development Program

NASA Technical Reports Server (NTRS)

Kenny, R. J.; Greene, W. D.

2016-01-01

This presentation covers the overall scope, schedule, and activities associated with the NASA - Marshall Space Flight Center (MSFC) involvement with the Combustion Stability Tool Development (CSTD) program. The CSTD program is funded by the Air Force Space & Missile Systems Center; it is approximately two years in duration and; and it is sponsoring MSFC to: design, fabricate, & execute multi-element hardware testing, support Air Force Research Laboratory (AFRL) single element testing, and execute testing of a small-scale, multi-element combustion chamber. Specific MSFC Engineering Directorate involvement, per CSTD-sponsored task, will be outlined. This presentation serves a primer for the corresponding works that provide details of the technical work performed by individual groups within MSFC.

Neutron Resonance Radiography for Explosives Detection: Technical Challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raas, W L; Blackburn, B; Boyd, E

2005-11-09

Fast Neutron Resonance Radiography (NRR) has recently become a focus of investigation as a supplement to conventional x-ray systems as a non-invasive, non-destructive means of detecting explosive material concealed in checked luggage or cargo containers at airports. Using fast (1-6 MeV) neutrons produced by the D(d,n){sup 3}He reaction, NRR provides both an imaging capability and the ability to determine the chemical composition of materials in baggage or cargo. Elemental discrimination is achieved by exploiting the resonance features of the neutron cross-section for oxygen, nitrogen, carbon, and hydrogen. Simulations have shown the effectiveness of multiple-element NRR through Monte Carlo transport methods;more » this work is focused on the development of a prototype system that will incorporate an accelerator-based neutron source and a neutron detection and imaging system to demonstrate the realistic capabilities of NRR in distinguishing the elemental components of concealed objects. Preliminary experiments have exposed significant technical difficulties unapparent in simulations, including the presence of image contamination from gamma ray production, the detection of low-fluence fast neutrons in a gamma field, and the mechanical difficulties inherent in the use of thin foil windows for gas cell confinement. To mitigate these concerns, a new gas target has been developed to simultaneously reduce gamma ray production and increase structural integrity in high flux gas targets. Development of a neutron imaging system and neutron counting based on characteristic neutron pulse shapes have been investigated as a means of improving signal to noise ratios, reducing irradiation times, and increasing the accuracy of elemental determination.« less

Using FAIRE (Formaldehyde-Assisted Isolation of Regulatory Elements) to isolate active regulatory DNA

PubMed Central

Simon, Jeremy M.; Giresi, Paul G.; Davis, Ian J.; Lieb, Jason D.

2013-01-01

Eviction or destabilization of nucleosomes from chromatin is a hallmark of functional regulatory elements of the eukaryotic genome. Historically identified by nuclease hypersensitivity, these regulatory elements are typically bound by transcription factors or other regulatory proteins. FAIRE (Formaldehyde-Assisted Isolation of Regulatory Elements) is an alternative approach to identify these genomic regions and has proven successful in a multitude of eukaryotic cell and tissue types. Cells or dissociated tissues are crosslinked briefly with formaldehyde, lysed, and sonicated. Sheared chromatin is subjected to phenol-chloroform extraction and the isolated DNA, typically encompassing 1–3% of the human genome, is purified. We provide guidelines for quantitative analysis by PCR, microarrays, or next-generation sequencing. Regulatory elements enriched by FAIRE display high concordance with those identified by nuclease hypersensitivity or ChIP, and the entire procedure can be completed in three days. FAIRE exhibits low technical variability, which allows its use in large-scale studies of chromatin from normal or diseased tissues. PMID:22262007

An Overview of Climatic Elements

NASA Technical Reports Server (NTRS)

Crutcher, H. L.; Johnson, D. L.

2007-01-01

This Technical Publication (TP) addresses some climatic elements with emphasis on atmospheric composition, including gas radiative characteristics. Solar radiation is discussed with considerable information on the mathematical and statistical formulae. On a worldwide basis, temperature and precipitation for the globe are discussed along with interaction in drought. Also included is the simultaneous interaction with winds, humidity, and solar radiation. Volcanology gets minimum treatment. The oceans and seas are treated in chart form along with the interrelationship of oceanic currents and El Nino and La Nina, and ENSO phenomena. Upper air circulations are discussed. Various cloud formations up to 85-95 km altitude are described. Information on tornadoes and hurricanes is also included. One section is devoted to the climate physical-chemical elements. A short discussion is given on the importance for the quality of data and/or information in descriptions of the climate. This TP presents only an overview or survey of these and other various climatic elements.

Probabilistic Structural Analysis Theory Development

NASA Technical Reports Server (NTRS)

Burnside, O. H.

1985-01-01

The objective of the Probabilistic Structural Analysis Methods (PSAM) project is to develop analysis techniques and computer programs for predicting the probabilistic response of critical structural components for current and future space propulsion systems. This technology will play a central role in establishing system performance and durability. The first year's technical activity is concentrating on probabilistic finite element formulation strategy and code development. Work is also in progress to survey critical materials and space shuttle mian engine components. The probabilistic finite element computer program NESSUS (Numerical Evaluation of Stochastic Structures Under Stress) is being developed. The final probabilistic code will have, in the general case, the capability of performing nonlinear dynamic of stochastic structures. It is the goal of the approximate methods effort to increase problem solving efficiency relative to finite element methods by using energy methods to generate trial solutions which satisfy the structural boundary conditions. These approximate methods will be less computer intensive relative to the finite element approach.

Structurally Integrated Antenna Concepts for HALE UAVs

NASA Technical Reports Server (NTRS)

Cravey, Robin L.; Vedeler, Erik; Goins, Larry; Young, W. Robert; Lawrence, Roland W.

2006-01-01

This technical memorandum describes work done in support of the Multifunctional Structures and Materials Team under the Vehicle Systems Program's ITAS (Integrated Tailored Aero Structures) Project during FY 2005. The Electromagnetics and Sensors Branch (ESB) developed three ultra lightweight antenna concepts compatible with HALE UAVs (High Altitude Long Endurance Unmanned Aerial Vehicles). ESB also developed antenna elements that minimize the interaction between elements and the vehicle to minimize the impact of wing flexure on the EM (electromagnetic) performance of the integrated array. In addition, computer models were developed to perform phase correction for antenna arrays whose elements are moving relative to each other due to wing deformations expected in HALE vehicle concepts. Development of lightweight, conformal or structurally integrated antenna elements and compensating for the impact of a lightweight, flexible structure on a large antenna array are important steps in the realization of HALE UAVs for microwave applications such as passive remote sensing and communications.

Technical and economic aspects of the Intelsat system

NASA Astrophysics Data System (ADS)

Jefferis, A. K.

1992-03-01

The paper gives some background on the Intelsat system and explains the financial principles of the organization, which operates as a cost sharing cooperative. The members contribute both capital and operating costs in accordance with their use. The determination of the measure of 'use' in such a complex system requires a careful analysis of the factors which cause the cost. Most of these are technical, based on the use of satellite power, bandwidth and similar factors. Others reflect service related features such as priority, long-term commitment and market elasticity. This last element is only taken into account after ensuring that every service fully contributes the marginal cost of providing it.

Thin EFG octagons

NASA Astrophysics Data System (ADS)

Kalejs, J. P.

1994-06-01

This report describes the impact of the technical achievements made in the first 18 months of the three year PVMaT program at Mobil Solar on lowering the manufacturing costs of its photovoltaic polycrystalline silicon-based modules. Manufacturing cost decreases are being achieved through a reduction of silicon material utilization, increases in productivity and yield in crystal growth, and through improvements in the laser cutting process for EFG wafers. The yield, productivity, and throughput advances made possible by these technical achievements are shown to be able to enhance future market share growth for Mobil Solar products as a consequence of significant reductions in a number of direct manufacturing cost elements in EFG wafer and module production.

Understanding the evolution of rice technology in China - from traditional agriculture to GM rice today.

PubMed

Shen, Xiaobai

2010-01-01

This paper provides an historical survey of the evolution of rice technology in China, from the traditional farming system to genetically modified rice today. Using sociotechnological analytical framework, it analyses rice technology as a socio-technical ensemble - a complex interaction of material and social elements, and discusses the specificity of technology development and its socio-technical outcomes. It points to two imperatives in rice variety development: wholesale transporting agricultural technology and social mechanism to developing countries are likely lead to negative consequences; indigenous innovation including deploying GM technology for seed varietal development and capturing/cultivating local knowledge will provide better solutions.

[The telemedical service centre as an essential element of the conceptual approach for telemonitoring of cardiac patients : Requirements on the service, quality, and technical realization of telemonitoring].

PubMed

Helms, T M; Müller, A; Perings, C; Köhler, F; Leonhardt, V; Rybak, K; Sack, S; Stockburger, M

2017-09-01

Telemonitoring as part of a treatment strategy supports and facilitates the monitoring, disease management and education of patients with heart failure and cardiac arrhythmias. Therefore, telemonitoring affects quality and success of the therapy. Thus, meeting the needs of the patients and of the involved health care professionals is important for the success of the telemonitoring service. Moreover, a high quality of the service has to be ensured. The following article describes several configuration options for telemonitoring services considering technical as well as quality- and service-related aspects.

How elements up to 118 were reached and how to go beyond

NASA Astrophysics Data System (ADS)

Düllmann, Christoph E.

2017-11-01

The new superheavy elements with Z=113, 115, 117, and 118 were recently accepted into the periodic table and have been named. Elements with Z≥112 are predominantly produced in 48Ca-induced fusion reactions on actinide targets. This pathway is exhausted at Z=118 due to the lack of target materials with sufficiently high proton number to reach elements with Z≥119. Search experiments for yet heavier elements were performed at GSI Darmstadt and FLNR Dubna. The reactions 50Ti + 249Bk, which leads to Z=119, as well as 64Ni + 238U, 58Fe + 244Pu, 54Cr + 248Cm, and 50Ti + 249Cf, leading to Z=120, have been studied. Despite a total duration of these experiments of more than one year, neither succeeded in the identification of a new element. To obtain improved guidance for better-informed search experiments, nuclear reaction studies appear necessary and have recently started. Also technical advances will be an important pillar to this end. At GSI, work towards a new continuous-wave linear accelerator is ongoing and is briefly described.

The Innovation Hyperlab - Linking Student Innovation at University and Pre-College Levels

NASA Astrophysics Data System (ADS)

Tagg, Randall

2012-02-01

We have created a laboratory environment to support collaboration between university and pre-college students on innovation and entrepreneurship projects. Called the ``Innovation Hyperlab,'' this facility is located in a K-12 complex called VistaPEAK schools in Aurora, Colorado. The lab is supported by four elements: a research-grade technical infrastructure of supplies and equipment for technical prototyping, a developing curriculum of ``learning modules on demand'' for rapid assimilation of technical skills, mentors from universities / medical schools / industry, and innovation projects stimulated by connections with the regional community. A current focus of projects is on medical technology development, linking tenth graders with university undergraduate research students and coordinated with the University of Colorado Denver's medical school. The Innovation Hyperlab is a work in progress and we will describe challenges that arise in connecting such a collaboration with traditional curriculum at both the university and pre-college levels.

Technical Assessment of the National Full Scale Aerodynamic Complex Fan Blades Repair

NASA Technical Reports Server (NTRS)

Young, Clarence P., Jr.; Dixon, Peter G.; St.Clair, Terry L.; Johns, William E.

1998-01-01

This report describes the principal activities of a technical review team formed to address National Full Scale Aerodynamic Complex (NFAC) blade repair problems. In particular, the problem of lack of good adhesive bonding of the composite overwrap to the Hyduliginum wood blade material was studied extensively. Description of action plans and technical elements of the plans are provided. Results of experiments designed to optimize the bonding process and bonding strengths obtained on a full scale blade using a two-step cure process with adhesive primers are presented. Consensus recommendations developed by the review team in conjunction with the NASA Ames Fan Blade Repair Project Team are provided along with lessons learned on this program. Implementation of recommendations resulted in achieving good adhesive bonds between the composite materials and wooden blades, thereby providing assurance that the repaired fan blades will meet or exceed operational life requirements.

Bioethics for Technical Experts

NASA Astrophysics Data System (ADS)

Asano, Shigetaka

Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

Management of optics. [for HEAO-2 X ray telescope

NASA Technical Reports Server (NTRS)

Kirchner, T. E.; Russell, M.

1981-01-01

American Science and Engineering, Inc., designed the large X-ray optic for the HEAO-2 X-ray Telescope. The key element in this project was the High Resolution Mirror Assembly (HRMA), subcontracting the fabrication of the optical surfaces and their assembly and alignment. The roles and organization of the key participants in the creation of HRMA are defined, and the degree of interaction between the groups is described. Management of this effort was extremely complex because of the intricate weaving of responsibilities, and AS&E, as HEAO-2 Program managers, needed to be well versed in the scientific objectives, the technical requirements, the program requirements, and the subcontract management. Understanding these factors was essential for implementing both technical and management controls, such as schedule and budget constraints, in-process control, residence requirements, and scientist review and feedback. Despite unforeseen technical problems and interaction differences, the HEAO-2 was built on schedule and to specification.

[High voltage objects and radiocommunication investments in view of requirements of the environmental protection act].

PubMed

Szuba, Marek

2006-01-01

This paper presents the most important elements of the localization procedure of high voltage overhead lines and substations and radiocommunication objects which are the source of electromagnetic fields. These fields are perceived as a major threat to human health. The point of departure to make a choice of investments is the special classification of technical installations described in one of the executive directive issued by virtue of the Environmental Protection Act. This special executive directive enumerates a lot of technical objects (installation), classified in the group of investments which have significant impact on the environment and some objects which could be classified in this group. For all this technical installations (e.g., overhead high voltage power lines) the provisions of the Environmental Protection Act impose an obligation to take particular steps to assure transparency of the environmental protection procedures, transborder procedures and the protection of areas included in the Natura 2000 network.

Outdoor Behavioral Healthcare: Definitions, Common Practice, Expected Outcomes, and a Nationwide Survey of Programs. Technical Report.

ERIC Educational Resources Information Center

Russell, Keith C.; Hendee, John C.

Outdoor behavioral healthcare (OBH) is an emerging mental health intervention/treatment to help adolescents overcome emotional, psychological, and addiction problems. Currently, over 100 OBH programs in the United States use elements of wilderness therapy to address adolescents' problem behaviors and foster responsibility and personal growth.…

What Counts As Mathematics?: Technologies of Power in Adult and Vocational Education. Mathematics Education Library.

ERIC Educational Resources Information Center

Fitzsimons, Gail E.

This book, aimed at mathematics and vocational educators and researchers, analyzes the historical, sociological, and practical elements of mathematics within vocational education against the emerging impact of technology. Focus is on the current situation of mathematics within Australian vocational and technical education and how that might be…

Circumventing Graphical User Interfaces in Chemical Engineering Plant Design

ERIC Educational Resources Information Center

Romey, Noel; Schwartz, Rachel M.; Behrend, Douglas; Miao, Peter; Cheung, H. Michael; Beitle, Robert

2007-01-01

Graphical User Interfaces (GUIs) are pervasive elements of most modern technical software and represent a convenient tool for student instruction. For example, GUIs are used for [chemical] process design software (e.g., CHEMCAD, PRO/II and ASPEN) typically encountered in the senior capstone course. Drag and drop aspects of GUIs are challenging for…

77 FR 75173 - Comprehensive Assessment of the Process for the Review of Device Submissions; Request for Comments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-19

... performing the technical analysis, management assessment, and program evaluation tasks required to address... premarket reviews that meet regulatory review standards. 2. Analysis of elements of the review process... process. This includes analysis of root causes for inefficiencies that may affect review performance and...

Creating Meaningful Inquiry in Inclusive Classrooms: Practitioners' Stories of Research

ERIC Educational Resources Information Center

Jones, Phyllis, Ed.; Whitehurst, Teresa, Ed.; Egerton, Jo, Ed.

2012-01-01

In recent years, the concept of teachers as researchers in both special and mainstream school settings has become part of our everyday language. Whilst many educational practitioners will see the need for research within their setting, many may not be familiar with the technical elements they believe are required. "Creating Meaningful Inquiry in…

A Public-Private Consortium Advances Cardiac Safety Evaluation: Achievements of the HESI Cardiac Safety Technical Committee

EPA Science Inventory

The evaluation of cardiovascular side-effects is a critical element in the development of all new drugs and chemicals. Cardiac safety issues have been and continue to be a major cause of attrition and withdrawal due to Adverse Drug Reactions (ADRs) in pharmaceutical drug developm...

Preparing Workers for Successful Careers

ERIC Educational Resources Information Center

Reese, Susan

2010-01-01

No doubt career and technical education (CTE) is integral in preparing a skilled workforce for today's jobs. Hands-on training is an important element of the CTE classroom, and when that occurs in an actual workplace setting, it may be called internship, apprenticeship or cooperative education. Whatever term is applied, it is another way in which…

Space shuttle program: Shuttle Avionics Integration Laboratory. Volume 7: Logistics management plan

NASA Technical Reports Server (NTRS)

1974-01-01

The logistics management plan for the shuttle avionics integration laboratory defines the organization, disciplines, and methodology for managing and controlling logistics support. Those elements requiring management include maintainability and reliability, maintenance planning, support and test equipment, supply support, transportation and handling, technical data, facilities, personnel and training, funding, and management data.

78 FR 76289 - Request for Information To Gather Technical Expertise Pertaining to Data Elements, Metrics, Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-17

... information. To assist us in making a determination on your request, we encourage you to identify any specific... consumer decision-making. Organizations that have developed, or are developing, ratings systems for.... The Department is interested in a PIRS that takes into account information important to the Federal...

The School Technology Primer: A Non-Technical Guide to Understanding School Technology.

ERIC Educational Resources Information Center

Little Inst. for School Facilities Research, Charlotte, NC.

This booklet is designed to provide educational administrators and planners with an easy guide to understanding the constantly evolving elements of school technology. The booklet presents a comprehensive overview of modern information systems in schools and how they can enhance the students' learning environment. Seven sections address a variety…

Pedagogy and Japanese Culture in a Distance Learning Environment

ERIC Educational Resources Information Center

Anderson, Bodi O.

2012-01-01

Current theoretical models of distance learning are driven by two impetuses: a technical CMC element, and a pedagogical foundation rooted strongly in the Western world, and driven by social constructivism. By and large these models have been exported throughout the world as-is. However, previous research has hinted at potential problems with these…

Analytical and experimental investigation of a 1/8-scale dynamic model of the shuttle orbiter. Volume 2: Technical report

NASA Technical Reports Server (NTRS)

Mason, P. W.; Harris, H. G.; Zalesak, J.; Bernstein, M.

1974-01-01

The methods and procedures used in the analysis and testing of the scale model are reported together with the correlation of the analytical and experimental results. The model, the NASTRAN finite element analysis, and results are discussed. Tests and analytical investigations are also reported.

Thermal energy storage

NASA Technical Reports Server (NTRS)

1980-01-01

The planning and implementation of activities associated with lead center management role and the technical accomplishments pertaining to high temperature thermal energy storage subsystems are described. Major elements reported are: (1) program definition and assessment; (2) research and technology development; (3) industrial storage applications; (4) solar thermal power storage applications; and (5) building heating and cooling applications.

std::string Append

DTIC Science & Technology

2015-10-01

UNCLASSIFIED AD-E403 689 Technical Report ARWSE-TR-14026 STD::STRING APPEND Tom Nealis...DATES COVERED (From – To) 4. TITLE AND SUBTITLE STD::STRING APPEND 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...DISTRIBUTION/AVAILABILITY STATEMENT Approved for public release; distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT Appending

Creating a Campus Climate That Supports Academic Excellence.

ERIC Educational Resources Information Center

Adams, Howard G.

This paper discusses the campus climate as a critical element in the academic development of college students, with emphasis on minority and women students pursuing engineering and other technical degrees. Reforming the campus climate to make it more receptive to minority and women students requires: (1) a clear mandate from top administrators to…

Preliminary Results Obtained in Integrated Safety Analysis of NASA Aviation Safety Program Technologies

NASA Technical Reports Server (NTRS)

2000-01-01

This is a quarterly listing of unclassified AGARD and RTO technical publications NASA received and announced in the NASA STI Database. Contents include 1) Sensor Data Fusion and Integration of the Human Element; 2) Planar Optical Measurement Methods for Gas Turbine Components; 3) RTO Highlights 1998, December 1998.

Managing the Transformation to an E-Learning Organisation.

ERIC Educational Resources Information Center

Simpson, Janet

The Douglas Mawson Institute (DMI) of TAFE (technical and further education), which operates more than four campuses in Australia with a diverse student body numbering approximately 17,000 (78 percent studying part-time), has initiated strategies to support the transformation to an e-learning organization. Major elements in the change model are…

Poetry for Today's Child.

ERIC Educational Resources Information Center

Carlson, Ruth Kearney

Ways of introducing children to the pleasures and value of poetry are discussed in this publication. Following a brief survey of various kinds of poems and the needs satisfied by poetry, some of the vocabulary and technical elements of poetic design--meter, stanza, rhyme, figures of speech, and selected verse forms--are explained and illustrated.…

Sustaining Professional and Organizational Growth of the ACTER through the Value of Mentorship

ERIC Educational Resources Information Center

Gordon, Howard R. D.

2016-01-01

The author examines selected aspects of mentorship and its value to the Association for Career and Technical Education Research (ACTER). He describes the Collaborative Mentoring Theory and the key elements of Daloz's Mentoring Model. Highlights of types of mentoring and suggested characteristics of Generation Xers and Millennials are reported. He…

75 FR 12540 - Electronic Tariff Filings; Notice of Technical Conference

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-16

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. RM01-5-000] Electronic... electronically starting April 1, 2010. One of the required electronic tariff filing's data elements is the Type of Filing Code. \\1\\ Electronic Tariff Filings, Order No. 714, 73 FR 57,515 (Oct. 3, 2008), 124 FERC...

Kansas Department of Transportation column expert : ultimate shear capacity of circular columns using the simplified modified compression field theory : [technical summary].

DOT National Transportation Integrated Search

2015-09-01

Even though the behavior of concrete elements subjected to shear force has been : studied for many years, researchers do not have a full agreement on concrete : shear resistance. This is mainly because of the many different mechanisms : that affect t...

TOPEX SDR Processing, October 1998. Volume 4

NASA Technical Reports Server (NTRS)

Lee, Jeffrey E.; Lockwood, Dennis W.

2003-01-01

This document is a compendium of the WFF TOPEX Software Development Team's knowledge regarding Sensor Data Record (SDR) Processing. It includes many elements of a requirements document, a software specification document, a software design document, and a user's manual. In the more technical sections, this document assumes the reader is familiar with TOPEX and instrument files.

The VOICES/VOCES Success Story: Effective Strategies for Training, Technical Assistance and Community-Based Organization Implementation

ERIC Educational Resources Information Center

Hamdallah, Myriam; Vargo, Sue; Herrera, Jennifer

2006-01-01

The Centers for Disease Control and Prevention's Diffusion of Effective Behavioral Interventions (DEBI) project successfully disseminated VOICES/VOCES, a brief video-based HIV risk reduction intervention targeting African American and Latino heterosexual men and women at risk for HIV infection. Elements of the dissemination strategy included a…

Education and Regional Development: An Irish Case Study.

ERIC Educational Resources Information Center

O'Buachalla, Seamus P.

Among the range of resources in the Mid-West Region of Ireland, higher education is an important, if costly, element. Five university institutions, eight colleges of education, two colleges of technology, and since 1970 nine regional technical colleges offer a higher education. The very large second level student body of the Limerick region was…

Role of Special Forces Liaison Elements in Future Multinational Operations

DTIC Science & Technology

2002-05-01

SOF simply with UW and the “old special-ops bugaboo of poor command and control and lack of coordination” that was displayed during Desert One, the...funding and allocating time for training and education in the areas of cultural, tactical, and technical expertise is not only a good investment for

Seeking a Balance: Discussion Strategies That Foster Reading with Authorial Empathy

ERIC Educational Resources Information Center

Brett, Aidan T.

2016-01-01

This study investigates the extent to which students' use of different discussion strategies fosters a balance between attending to the technical elements of authored texts and responding empathetically. Because small-group discussion is a common approach to literary study, the analysis focuses on two small-group discussions of "Charlie…

Search for extraterrestrial intelligence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morrison, P.; Billingham, J.; Wolfe, J.

1979-01-01

The findings of a series of workshops on the search for extraterrestrial intelligence are presented. The major conclusions of the deliberations are presented. Six of the most interesting and significant elements of the debate are presented in the form of Colloquies. A selection of detailed technical arguments about various aspects of the SETI endeavor is documented. (GHT)

The efficiency of the use of composite materials in electrotechnical equipment

NASA Astrophysics Data System (ADS)

Kim, K.; Ivanov, S.

2018-02-01

The indicators of the efficiency of electrical installations are directly connected with the creating and using of new composite materials with the desired performance properties. The practical application of composite materials is one of the perspective scientific and technical directions, providing the increase of the efficiency of electrical installations due to the sealing of current parts by protecting them from the external medium. The technical characteristics of the composite material match to its structure and depend on the properties of the individual components. The verification of the compliance of material parameters is implemented by the methods of the computer analysis of a model of composite material in the form of the structure in which the individual elements have thermodynamic properties of the corresponding phase state. In the study the topology of individual elements in the material structure is defined by the conditional boundaries of the section within the studied composite. The efficiency of using the composite materials includes the raising of electrical safety, increasing the durability, reducing the costs of maintenance and repair and the extension of the scope of installations.

A Hidden Portrait by Edgar Degas

NASA Astrophysics Data System (ADS)

Thurrowgood, David; Paterson, David; de Jonge, Martin D.; Kirkham, Robin; Thurrowgood, Saul; Howard, Daryl L.

2016-08-01

The preservation and understanding of cultural heritage depends increasingly on in-depth chemical studies. Rapid technological advances are forging connections between scientists and arts communities, enabling revolutionary new techniques for non-invasive technical study of culturally significant, highly prized artworks. We have applied a non-invasive, rapid, high definition X-ray fluorescence (XRF) elemental mapping technique to a French Impressionist painting using a synchrotron radiation source, and show how this technology can advance scholarly art interpretation and preservation. We have obtained detailed technical understanding of a painting which could not be resolved by conventional techniques. Here we show 31.6 megapixel scanning XRF derived elemental maps and report a novel image processing methodology utilising these maps to produce a false colour representation of a “hidden” portrait by Edgar Degas. This work provides a cohesive methodology for both imaging and understanding the chemical composition of artworks, and enables scholarly understandings of cultural heritage, many of which have eluded conventional technologies. We anticipate that the outcome from this work will encourage the reassessment of some of the world’s great art treasures.

Dual- and Multi-Energy CT: Principles, Technical Approaches, and Clinical Applications

PubMed Central

Leng, Shuai; Yu, Lifeng; Fletcher, Joel G.

2015-01-01

In x-ray computed tomography (CT), materials having different elemental compositions can be represented by identical pixel values on a CT image (ie, CT numbers), depending on the mass density of the material. Thus, the differentiation and classification of different tissue types and contrast agents can be extremely challenging. In dual-energy CT, an additional attenuation measurement is obtained with a second x-ray spectrum (ie, a second “energy”), allowing the differentiation of multiple materials. Alternatively, this allows quantification of the mass density of two or three materials in a mixture with known elemental composition. Recent advances in the use of energy-resolving, photon-counting detectors for CT imaging suggest the ability to acquire data in multiple energy bins, which is expected to further improve the signal-to-noise ratio for material-specific imaging. In this review, the underlying motivation and physical principles of dual- or multi-energy CT are reviewed and each of the current technical approaches is described. In addition, current and evolving clinical applications are introduced. © RSNA, 2015 PMID:26302388

A Hidden Portrait by Edgar Degas

PubMed Central

Thurrowgood, David; Paterson, David; de Jonge, Martin D.; Kirkham, Robin; Thurrowgood, Saul; Howard, Daryl L.

2016-01-01

The preservation and understanding of cultural heritage depends increasingly on in-depth chemical studies. Rapid technological advances are forging connections between scientists and arts communities, enabling revolutionary new techniques for non-invasive technical study of culturally significant, highly prized artworks. We have applied a non-invasive, rapid, high definition X-ray fluorescence (XRF) elemental mapping technique to a French Impressionist painting using a synchrotron radiation source, and show how this technology can advance scholarly art interpretation and preservation. We have obtained detailed technical understanding of a painting which could not be resolved by conventional techniques. Here we show 31.6 megapixel scanning XRF derived elemental maps and report a novel image processing methodology utilising these maps to produce a false colour representation of a “hidden” portrait by Edgar Degas. This work provides a cohesive methodology for both imaging and understanding the chemical composition of artworks, and enables scholarly understandings of cultural heritage, many of which have eluded conventional technologies. We anticipate that the outcome from this work will encourage the reassessment of some of the world’s great art treasures. PMID:27490856

Comparison of premortem and postmortem estimates of plutonium deposited in the skeleton and liver of six individuals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sula, M.J.; Bihl, D.E.; Carbaugh, E.H.

1988-04-01

Assessment of organ burdens after internal exposures to radionuclides is often necessary to evaluate the health and regulatory implications of the exposure. The assessment of plutonium activity in skeleton and liver is usually estimated from measurements of plutonium excreted via urine. As part of the overall evaluation of internal dose assessment techniques, it is useful to compare the results of organ burden estimates made from evaluation of urinary excretion data with those made at death from tissue samples collected posthumously from the individual. Estimates of plutonium in the skeleton and liver, based on postmortem analysis of tissue samples for sixmore » individuals, were obtained from the US Transuranium Registry (USTR). Bioassay data and other radiation exposure information obtained from the individuals' files were used to estimate their skeleton and liver burdens at the times of their deaths, and these estimates were compared to those obtained through tissue analysis. 6 refs., 2 tabs.« less

United States transuranium and uranium registries. Annual report, October 1, 1995--September 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kathren, R.L.; Ehrhart, S.M.

1997-04-01

This Annual Report covers the period October 1, 1995 through September 30, 1996, and includes both scientific and administrative activities. As of September 30, 1996, the Registries had a total of 886 registrants of whom 350 were deceased and 292 classified as active. An anticipated funding cut of approximately 35% for the period beginning October 1, 1996, necessitated some staff cuts, but it is anticipated that the Registries core research will be maintained albeit at a somewhat slower pace. The Registries received approximately 60 public information requests or inquiries ranging over a wide range of topics, about a third ofmore » which came from the media or official agencies, including Congress. Specific noteworthy inquiries were received from the President`s Advisory Committee on the Gulf War Veterans with regard to uranium biokinetics and toxicity, and from the County of Los Angeles and the State of California with regard to the management and dosimetry of two separate instances of acute accidental intakes of {sup 241}Am.« less

Biotransport of transuranium radionuclides in dairy animals: a data summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sutton, W.W.; Patzer, R.G.; Potter, G.D.

In recent years, the Environmental Monitoring Systems Laboratory at Las Vegas, Nevada (EMSL-LV) has carried out a series of studies on the biological transport of plutonium, americium, neptunium, and curium in lactating dairy cattle and goats. Ruminants in general and cattle in particular form one of the more important links in the human food chain. Milk and milk products constitute a significant portion of the human diet, especially for children. This summary consists of a compilation of detailed data from a series of previously published studies. It has been prepared to present the data from all of these studies inmore » a single source to be used by regulatory agencies in their transport modeling and hazard assessment activities. Selected source materials for the data presented in this document have been published either in the Proceedings of the Nevada Applied Ecology Group (NAEG) or as EMSL-LV publications and are listed in the References section.« less

A Government/Industry Summary of the Design Analysis Methods for Vibrations (DAMVIBS) Program

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G. (Compiler)

1993-01-01

The NASA Langley Research Center in 1984 initiated a rotorcraft structural dynamics program, designated DAMVIBS (Design Analysis Methods for VIBrationS), with the objective of establishing the technology base needed by the rotorcraft industry for developing an advanced finite-element-based dynamics design analysis capability for vibrations. An assessment of the program showed that the DAMVIBS Program has resulted in notable technical achievements and major changes in industrial design practice, all of which have significantly advanced the industry's capability to use and rely on finite-element-based dynamics analyses during the design process.

Study for identification of Beneficial Uses of Space (BUS). Volume 2: Technical report. Book 5: Study methods and trade studies

NASA Technical Reports Server (NTRS)

1975-01-01

A glossary of terms, a work breakdown structure, and work element descriptions, resource needs, and costs are introduced. The generic work breakdown structure was utilized to organize specific structures for each product under study; each structure containing both space and ground elements arrived at via mutual interaction. Concept definition and assessment, provided the study team and the participants visibility of the limits, and the organization of the efforts provided by both groups spelling out where such efforts fit into the generation of processing concepts.

The strategy for improving water-quality monitoring in the United States; final report of the Intergovernmental Task Force on Monitoring Water Quality; technical appendices

USGS Publications Warehouse

,

1995-01-01

The Intergovernmental Task Force on Monitoring Water Quality (ITFM) prepared this report in collaboration with representatives of all levels of government and the private sector. The report recommends a strategy for nationwide water-quality monitoring and technical monitoring improvements to support sound water-quality decisionmaking. The strategy is intended to achieve a better return on public and private investments in monitoring, environmental protection, and natural resources management. It is also designed to expand the base of information useful to a variety of users at multiple geographic scales. Institutional and technical changes are needed to improve water-quality monitoring and to meet the full range of monitoring requirements. Monitoring must be incorporated as a critical element of program planning, implementation, and evaluation. The strategy includes recommendations in many key elements, such as the development of goal-oriented monitoring and indicators, institutional collaboration, and methods comparability. Initial actions have been taken to implement the strategy. Several Federal agencies have jointly purchased and shared remotely sensed land-cover information needed for water assessment. Major agency data systems are using common data-element names and reference tables that will ensure easy sharing of data. A number of States have held meetings with collectors of water information to initiate statewide monitoring strategies. New monitoring guidance has been developed for Federal water-quality grants to States. Many State offices have changed monitoring programs to place emphasis on priority watersheds and to improve assessment of water quality. As the competition increases for adequate supplies of clean water, concerns about public health and the environment escalate, and more demands are placed on the water information infrastructure. To meet these demands, the collaborative approach has already produced benefits, which will continue to grow as the recommendations are implemented

2D and 3D GPR imaging of structural ceilings in historic and existing constructions

NASA Astrophysics Data System (ADS)

Colla, Camilla

2014-05-01

GPR applications in civil engineering are to date quite diversified. With respect to civil constructions and monumental buildings, detection of voids, cavities, layering in structural elements, variation of geometry, of moisture content, of materials, areas of decay, defects, cracks have been reported in timber, concrete and masonry elements. Nonetheless, many more fields of investigation remain unexplored. This contribution gives an account of a variety of examples of structural ceilings investigation by GPR radar in reflection mode, either as 2D or 3D data acquisition and visualisation. Ceilings have a pre-eminent role in buildings as they contribute to a good structural behaviour of the construction. Primarily, the following functions can be listed for ceilings: a) they carry vertical dead and live loads on floors and distribute such loads to the vertical walls; b) they oppose to external horizontal forces such as wind loads and earthquakes helping to transfer such forces from the loaded element to the other walls; c) they contribute to create the box skeleton and behaviour of a building, connecting the different load bearing walls and reducing the slenderness and flexural instability of such walls. Therefore, knowing how ceilings are made in specific buildings is of paramount importance for architects and structural engineers. According to the type of building and age of construction, ceilings may present very different solutions and materials. Moreover, in existing constructions, ceilings may have been substituted, modified or strengthened due to material decay or to change of use of the building. These alterations may often go unrecorded in technical documentation or technical drawings may be unavailable. In many cases, the position, orientation and number of the load carrying elements in ceilings may be hidden or not be in sight, due for example to the presence of false ceilings or to technical plants. GPR radar can constitute a very useful tool for investigating with rapidity and high resolution, thin as well as very thick ceilings, in a non-destructive manner. Ceilings may be made up as masonry vaults or timber/metal/concrete beams and elements laid down in one or two directions or, again, can be made as a combination of the above. A number of cases are here presented reporting on typical features to be recognised in radargrams in order to distinguish the material and possible shape of the relevant objects with the aim of providing a first small catalogue useful to the radar user and to professionals. This abstract is of interest for COST Action TU1208.

Predictors of Attitudes Toward Non-Technical Skills in Farming.

PubMed

Irwin, Amy; Poots, Jill

2018-01-01

Farming is a high-risk sector with up to 170,000 worldwide fatalities reported per year; it is therefore vital to identify methods of mitigating the dangers of this industry. Research within high-risk industries, such as aviation, shipping, and agriculture, has identified the importance of non-technical skills (NTS) in maintaining effective, safe performance and reducing error and injury. However, there is a lack of research evaluating factors that may contribute to NTS attitudes and behaviors. As a first step to address this literature gap, the current study evaluated a range of individual and environmental factors as potential predictors of attitudes toward NTS in agriculture. A sample of 170 farmers from within the United Kingdom and Ireland were surveyed using an online questionnaire. The questionnaire included measures of personality, stress, attitudes toward safety (safety climate, motivation, and risk), environmental stressors (workload, work-life imbalance), and non-technical skills (team and lone worker). Attitudes toward safety climate, compliance, and motivation showed a significant association with both team-based and lone worker NTS. Conscientiousness correlated positively with the majority of the NTS elements. Multiple regression analysis indicated neuroticism and conscientiousness demonstrated capacity to predict NTS attitudes. Concerns about costs and equipment, attitudes toward safety climate, and safety motivation were also found to be significant predictors of NTS attitudes. The results indicate the utility of individual characteristics and environmental factors when predicting farming NTS attitudes. As a result, these elements could be important when evaluating engagement with NTS and developing NTS training initiatives in agriculture.

Elements of the niche for adult stem cell expansion

PubMed Central

Redondo, Patricia A; Pavlou, Marina; Loizidou, Marilena; Cheema, Umber

2017-01-01

Adult stem cells are crucial for tissue homeostasis. These cells reside within exclusive locations in tissues, termed niches, which protect adult stem cell fidelity and regulate their many functions through biophysical-, biochemical- and cellular-mediated mechanisms. There is a growing understanding of how these mechanisms and their components contribute towards maintaining stem cell quiescence, self-renewal, expansion and differentiation patterns. In vitro expansion of adult stem cells is a powerful tool for understanding stem cell biology, and for tissue engineering and regenerative medicine applications. However, it is technically challenging, since adult stem cell removal from their native microenvironment has negative repercussions on their sustainability. In this review, we overview specific elements of the biomimetic niche and how recreating such elements can help in vitro propagation of adult stem cells. PMID:28890779

Elements of the niche for adult stem cell expansion.

PubMed

Redondo, Patricia A; Pavlou, Marina; Loizidou, Marilena; Cheema, Umber

2017-01-01

Adult stem cells are crucial for tissue homeostasis. These cells reside within exclusive locations in tissues, termed niches, which protect adult stem cell fidelity and regulate their many functions through biophysical-, biochemical- and cellular-mediated mechanisms. There is a growing understanding of how these mechanisms and their components contribute towards maintaining stem cell quiescence, self-renewal, expansion and differentiation patterns. In vitro expansion of adult stem cells is a powerful tool for understanding stem cell biology, and for tissue engineering and regenerative medicine applications. However, it is technically challenging, since adult stem cell removal from their native microenvironment has negative repercussions on their sustainability. In this review, we overview specific elements of the biomimetic niche and how recreating such elements can help in vitro propagation of adult stem cells.

[Change management: An analysis of actors; perceptions about technical assistance in the Democratic Republic of Congo].

PubMed

Ribesse, Nathalie; Iyeti, Alain; Macq, Jean

2015-01-01

Technical assistance (TA) is a common component of health system strengthening interventions. This type of intervention is too often designed and evaluated according to a logic that fails to take into account social complexity. Actors' perceptions are one element of this complexity. This article presents a study conducted in the Democratic Republic of Congo designed to identify perceptions concerning two types of technical support providers for health system strengthening: long-term technical assistants (agents of development agencies) and provincial technical advisors (agents of the Ministry of Health). Interviews were conducted with an innovative tool inspired by the principles of systems thinking. Interviewees were actors involved in a TA intervention in the province of Bandundu. Their expectations regarding TA providers were identified in terms of personal characteristics (knowledge, know-how and interpersonal skills), roles, and styles of interaction for capacity building ("interventionist/ prescriptive axes"). Interviewees emphasized the importance of mutual learning and the quality of interactions, which depends on TA provider's interpersonal skills and mutual willingness. Perceptions of TA provider's characteristics tend to be similar, but several differences were observed concerning the expectations about the roles of TAs, and the style that should be adopted for capacity building. Ignoring these differences in expectations may be a threat to the effectiveness of TA.

The Independent Technical Analysis Process Final Report 2006-2007.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duberstein, Corey; Ham, Kenneth; Dauble, Dennis

2007-03-01

The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities. The Independent Technical Analysis Process (ITAP) was created to provide non-routine analysis for fish and wildlife agencies and tribes in particular and the public in general on matters related tomore » juvenile and adult salmon and steelhead passage through the mainstem hydrosystem. The process was designed to maintain the independence of analysts and reviewers from parties requesting analyses, to avoid potential bias in technical products. The objectives identified for this project were to administer a rigorous, transparent process to deliver unbiased technical assistance necessary to coordinate recommendations for storage reservoir and river operations that avoid potential conflicts between anadromous and resident fish. Seven work elements, designated by numbered categories in the Pisces project tracking system, were created to define and accomplish project goals as follows: (1) 118 Coordination - Coordinate technical analysis and review process: (a) Retain expertise for analyst/reviewer roles. (b) Draft research directives. (c) Send directive to the analyst. (d) Coordinate two independent reviews of the draft report. (e) Ensure reviewer comments are addressed within the final report. (2) 162 Analyze/Interpret Data - Implement the independent aspects of the project. (3) 122 Provide Technical Review - Implement the review process for the analysts. (4) 132 Produce Annual Report - FY06 annual progress report with Pisces Disseminate (5) 161 Disseminate Raw/Summary Data and Results - Post technical products on the ITAP web site. (6) 185-Produce Pisces Status Report - Provide periodic status reports to BPA. (7) 119 Manage and Administer Projects - project/contract administration.« less

Systems Integration Processes for NASA Ares I Crew Launch Vehicle

NASA Technical Reports Server (NTRS)

Taylor, James L.; Reuter, James L.; Sexton, Jeffrey D.

2006-01-01

NASA's Exploration Initiative will require development of many new elements to constitute a robust system of systems. New launch vehicles are needed to place cargo and crew in stable Low Earth Orbit (LEO). This paper examines the systems integration processes NASA is utilizing to ensure integration and control of propulsion and nonpropulsion elements within NASA's Crew Launch Vehicle (CLV), now known as the Ares I. The objective of the Ares I is to provide the transportation capabilities to meet the Constellation Program requirements for delivering a Crew Exploration Vehicle (CEV) or other payload to LEO in support of the lunar and Mars missions. The Ares I must successfully provide this capability within cost and schedule, and with an acceptable risk approach. This paper will describe the systems engineering management processes that will be applied to assure Ares I Project success through complete and efficient technical integration. Discussion of technical review and management processes for requirements development and verification, integrated design and analysis, integrated simulation and testing, and the integration of reliability, maintainability and supportability (RMS) into the design will also be included. The Ares I Project is logically divided into elements by the major hardware groupings, and associated management, system engineering, and integration functions. The processes to be described herein are designed to integrate within these Ares I elements and among the other Constellation projects. Also discussed is launch vehicle stack integration (Ares I to CEV, and Ground and Flight Operations integration) throughout the life cycle, including integrated vehicle performance through orbital insertion, recovery of the first stage, and reentry of the upper stage. The processes for decomposing requirements to the elements and ensuring that requirements have been correctly validated, decomposed, and allocated, and that the verification requirements are properly defined to ensure that the system design meets requirements, will be discussed.

US Transuranium and Uranium Registries case study on accidental exposure to uranium hexafluoride.

PubMed

Avtandilashvili, Maia; Puncher, Matthew; McComish, Stacey L; Tolmachev, Sergei Y

2015-03-01

The United States Transuranium and Uranium Registries' (USTUR) whole-body donor (Case 1031) was exposed to an acute inhalation of uranium hexafluoride (UF6) produced from an explosion at a uranium processing plant 65 years prior to his death. The USTUR measurements of tissue samples collected at the autopsy indicated long-term retention of inhaled slightly enriched uranium material (0.85% (235)U) in the deep lungs and thoracic lymph nodes. In the present study, the authors combined the tissue measurement results with historical bioassay data, and analysed them with International Commission on Radiological Protection (ICRP) respiratory tract models and the ICRP Publication 69 systemic model for uranium using maximum likelihood and Bayesian statistical methods. The purpose of the analysis was to estimate intakes and model parameter values that best describe the data, and evaluate their effect on dose assessment. The maximum likelihood analysis, which used the ICRP Publication 66 human respiratory tract model, resulted in a point estimate of 79 mg of uranium for the occupational intake composed of 86% soluble, type F material and 14% insoluble, type S material. For the Bayesian approach, the authors applied the Markov Chain Monte Carlo method, but this time used the revised human respiratory tract model, which is currently being used by ICRP to calculate new dose coefficients for workers. The Bayesian analysis estimated that the mean uranium intake was 160 mg, and calculated the case-specific lung dissolution parameters with their associated uncertainties. The parameters were consistent with the inhaled uranium material being predominantly soluble with a small but significant insoluble component. The 95% posterior range of the rapid dissolution fraction (the fraction of deposited material that is absorbed to blood rapidly) was 0.12 to 0.91 with a median of 0.37. The remaining fraction was absorbed slowly, with a 95% range of 0.000 22 d(-1) to 0.000 36 d(-1) and a median of 0.000 31 d(-1). The effective dose per unit intake calculated using the dissolution parameters derived from the maximum likelihood and the Bayesian analyses was higher than the current ICRP dose coefficient for type F uranium by a factor of 2 or 7, respectively; the higher value of the latter was due to use of the revised respiratory tract model. The dissolution parameter values obtained here may be more appropriate to use for radiation protection purposes when individuals are exposed to a UF6 mixture that contains an insoluble uranium component.

Standardized Cardiovascular Data for Clinical Research, Registries, and Patient Care

PubMed Central

Anderson, H. Vernon; Weintraub, William S.; Radford, Martha J.; Kremers, Mark S.; Roe, Matthew T.; Shaw, Richard E.; Pinchotti, Dana M.; Tcheng, James E.

2013-01-01

Relatively little attention has been focused on standardization of data exchange in clinical research studies and patient care activities. Both are usually managed locally using separate and generally incompatible data systems at individual hospitals or clinics. In the past decade there have been nascent efforts to create data standards for clinical research and patient care data, and to some extent these are helpful in providing a degree of uniformity. Nevertheless these data standards generally have not been converted into accepted computer-based language structures that could permit reliable data exchange across computer networks. The National Cardiovascular Research Infrastructure (NCRI) project was initiated with a major objective of creating a model framework for standard data exchange in all clinical research, clinical registry, and patient care environments, including all electronic health records. The goal is complete syntactic and semantic interoperability. A Data Standards Workgroup was established to create or identify and then harmonize clinical definitions for a base set of standardized cardiovascular data elements that could be used in this network infrastructure. Recognizing the need for continuity with prior efforts, the Workgroup examined existing data standards sources. A basic set of 353 elements was selected. The NCRI staff then collaborated with the two major technical standards organizations in healthcare, the Clinical Data Interchange Standards Consortium and Health Level 7 International, as well as with staff from the National Cancer Institute Enterprise Vocabulary Services. Modeling and mapping were performed to represent (instantiate) the data elements in appropriate technical computer language structures for endorsement as an accepted data standard for public access and use. Fully implemented, these elements will facilitate clinical research, registry reporting, administrative reporting and regulatory compliance, and patient care. PMID:23500238

Defense Technical Information Center Cataloging Guidelines

DTIC Science & Technology

1994-02-01

24 Field 10 - Personal Authors ............................................................ 27 Field 11 - Date of...Stanford, Calif. 24 . If the subordinate element of a heading begins with a personal name, that name is written without rearrangement. APPEARS AS...country is not repeated if ’ncluded in the heading. APPEARS AS: ENTER AS: Centro Brasileiro de Pesquisas Centro Brasileiro de Fisicas, Rio de Janeiro

TOPEX Software Document Series. Volume 5; Rev. 1; TOPEX GDR Processing

NASA Technical Reports Server (NTRS)

Lee, Jeffrey; Lockwood, Dennis; Hancock, David W., III

2003-01-01

This document is a compendium of the WFF TOPEX Software Development Team's knowledge regarding Geophysical Data Record (GDR) Processing. It includes many elements of a requirements document, a software specification document, a software design document, and a user's manual. In the more technical sections, this document assumes the reader is familiar with TOPEX and instrument files.

Social and economic profile technical guide

Treesearch

David Seesholtz; Denise Wickwar; John C. Russell

2006-01-01

A social and economic profile is a key element of a social assessment. A social and economic assessment or profile is used by line officers, planning staff social scientists, and others to inform both forest planning activities and project-level work. It is important to discover how planning and management decisions made by National Forest System staff will affect...

Detailed technical plan for Test Program Element-III (TPE-III) of the first wall/blanket shield engineering test program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, L.R.; Praeg, W.F.

1982-03-01

The experimental requirements, test-bed design, and computational requirements are reviewed and updated. Next, in Sections 3, 4 and 5, the experimental plan, instrumentation, and computer plan, respectively, are described. Finally, Section 6 treats other considerations, such as personnel, outside participation, and distribution of results.

The Ecosystem Factor in Supporting Wiki Initiative for Knowledge Sharing in Malaysian Public Organisation

ERIC Educational Resources Information Center

Khuzaimah, Khairil Hizar Md; Affandi, Haryanti Mohd; Hassan, Fadzil

2015-01-01

The purpose of this paper is to highlight the significance of considering the organizational ecosystem in implementing wikis for knowledge sharing.The findings suggest that a prerequisite of an effective wiki is the appreciation of the factors that make up the organizational ecosystem; technical and organizational factors are variable elements of…

77 FR 23370 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-18

... CONTRACT CLAUSES 52.212-5 [Amended] 0 2. Amend section 52.212-5 by removing from paragraph (b)(7) ``(Jan... ADMINISTRATION 48 CFR Parts 1 and 52 [FAC 2005-58; Item IV; Docket 2012-0079; Sequence 2] Federal Acquisition... update certain elements in 48 CFR parts 1 and 52, this document makes editorial changes to the FAR. List...

A Primer on Decision Analysis for Individually Prescribed Instruction. ACT Technical Bulletin No. 17.

ERIC Educational Resources Information Center

Davis, Charles E.; And Others

A coherent system of decision making is described that may be incorporated into an instructional sequence to provide a supplement to the experience-based judgment of the classroom teacher. The elements of this decision process incorporate prior information such as a teacher's past experience, experimental results such as a test score, and…

Configuration study for a 30 GHz monolithic receive array: Technical assessment

NASA Technical Reports Server (NTRS)

Nester, W. H.; Cleaveland, B.; Edward, B.; Gotkis, S.; Hesserbacker, G.; Loh, J.; Mitchell, B.

1984-01-01

The current status of monolithic microwave integrated circuits (MMICs) in phased array feeds is discussed from the point of view of cost performance, reliability, and design considerations. Transitions to MMICs, compatible antenna radiating elements and reliability considerations are addressed. Hybrid antennas, feed array antenna technology, and offset reflectors versus phased arrays are examined.

Technical Specifications for Hardware and Software, and Maintenance in Support of Computer Literacy Program. Volume II.

ERIC Educational Resources Information Center

District of Columbia Public Schools, Washington, DC.

Designed for use by vendors, this guide provides an overview of the objectives for the 5-year computer literacy program to be implemented in the District of Columbia Public Schools; outlines requirements which are mandatory elements of vendors' bids unless explicitly designated "desirable"; and details specifications for computing…

A Quantitative Comparison of the Relative Performance of VHF and UHF Broadcast Systems. Technical Monograph Number 1.

ERIC Educational Resources Information Center

Rubin, Philip A.; And Others

A study was undertaken to: (1) assess problems with UHF television systems; and (2) identify problem-solving activities on which different broadcast institutions could cooperate, The model for comparing UHF with VHF broadcast/reception services assigned performance disparity figures to each of the following elements: (1) transmitter and…

Axial Magneto-Inductive Effect in Soft Magnetic Microfibers, Test Methodology, and Experiments

DTIC Science & Technology

2016-03-24

NUWC-NPT Technical Report 12,186 24 March 2016 Axial Magneto-Inductive Effect in Soft Magnetic Microfibers, Test Methodology , and...Microfibers, Test Methodology , and Experiments 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Anthony B...5 4 MEASUREMENTS AND EXPERIMENTAL APPARATUS ...........................................9 5 SAMPLE PREPARATION

A Collaborative Capstone to Develop a Mobile Hospital Clinic Application through a Student Team Competition

ERIC Educational Resources Information Center

Wong, Wilson; Pepe, James; Stahl, James; Englander, Irv

2013-01-01

A new collaborative capstone model is presented that consists of three synergistic elements: (1) a capstone course component; (2) a business component; and (3) an advanced technical course component geared towards enhancing the student capstone learning experience. The model was fully implemented at Bentley University in spring 2012 with…

Designing Effective Professional Development: Lessons from the Eisenhower Program [and] Technical Appendices.

ERIC Educational Resources Information Center

Garet, Michael S.; Birman, Beatrice F.; Porter, Andrew C.; Desimone, Laura; Herman, Rebecca

The professional development of teachers is a crucial element of the nation's efforts to improve education. In recent years, these efforts have sought to foster high standards for teaching and learning for all of the nation's children, and almost all states have met federal requirements for developing challenging statewide content standards. Such…

IS/IT Education vs. Business Education: The Plight of Social Collapse in Technical Business Environments

ERIC Educational Resources Information Center

Hall, Brian

2011-01-01

In an age when information, management and technology are supposed to be hand-in-hand, there is often a rift between these elements when considering people and comportment. The detachment is caused by a distressing lack of understanding between Information Systems (IS)/Information Technology (IT) students and professionals and those they interact…

The Concept of Energy in Psychological Theory. Cognitive Science Program, Technical Report No. 86-2.

ERIC Educational Resources Information Center

Posner, Michael I.; Rothbart, Mary Klevjord

This paper describes a basic framework for integration of computational and energetic concepts in psychological theory. The framework is adapted from a general effort to understand the neural systems underlying cognition. The element of the cognitive system that provides the best basis for attempting to relate energetic and computational ideas is…

Attention, Intention and the Structure of Discourse. Technical Report No. 380.

ERIC Educational Resources Information Center

Grosz, B. J.; Sidner, C. L.

Developing and integrating two lines of research, one focusing on discourse and the other on intention recognition in discourse, this paper presents the basic elements of a computational theory of discourse. The paper argues that by specifying the basic units a discourse comprises and the ways in which they can relate, an account of discourse…

Demographic Trends and the Scientific and Engineering Work Force. A Technical Memorandum.

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. Office of Technology Assessment.

The Federal Government has acknowledged its key role in educating and assuring an adequate supply of scientists and engineers since World War II. Although scientists and engineers represent only three percent of the national work force, they are considered by many to be a crucial element in the nation's efforts to improve its economic…

Dynaflow User’s Guide

DTIC Science & Technology

1988-11-01

264 ANALYSIS RESTART. ............. ..... ....... 269 1.0 TITLE CARD. .............. ............. 271 2.0 CONTROL CARDS...stress soil model will provide a tool for such analysis of waterfront structures. To understand the significance of liquefaction, it is important to note...Implementing this effective stress soil model into a finite element computer program would allow analysis of soil and structure together. TECHNICAL BACKGROUND

Common Elements of Risk

DTIC Science & Technology

2006-04-01

8 Figure 5 : Threat and Operational Risk .................................................................... 9 Figure 6: Work Process...technical note might be applied to selected risk management topics. Finally, Section 5 , “Conclusion,” completes the report by summarizing the history...addressed in Section 5 . CMU/SEI-2006-TN-014 5 So far, our discussion has focused on the conceptual aspects of risk . The next section explores risk’s

FY 1991 RDT&E Descriptive Summaries

DTIC Science & Technology

1990-01-01

OF PROJECT : The Defense Sciences program element provides the technical foundation for long-term improvements in military equiment...DESCRIPTION OF PROJECT : Develop the fundamental technology in advanced digital structures and network concepts for smaller, more powerful, less expensive...DESCRIPTION OF PROJECT : The 1985 Defense Science Board (DSB) noted that the United States was behind and failing further behind in armor and